WorldWideScience

Sample records for delaware basin drilling

  1. Delaware basin/Central basin platform margin: The development of a subthrust deep-gas province in the Permian Basin

    Energy Technology Data Exchange (ETDEWEB)

    Purves, W.J. (Mobil Oil Corp., Midland, TX (USA)); Ting, S.C. (Mobil, Farmers Branch, TX (USA))

    1990-05-01

    A deep-gas-prone province was identified along the Delaware basin/Central Basin platform margin, a margin conventionally interpreted to be bounded by high-angle normal or high-angle reverse structures. Redefinition of the tectonic style between the Delaware basin and the adjacent platform resulted in the identification of this Delaware basin/Central Basin platform subthrust province and a giant prospect within it. Definition of a giant-sized gas prospect in northern Pecos County, Texas, revealed that portions of this margin may be characterized by shingled, low-angle, eastward-dipping, basement involved thrust faults. Interpretations suggest that hidden, subthrust footwall structures may trend discontinuously for greater than 100 mi along this structural margin. Subthrust footwall structures formed as basinal buttress points for the Central Basin platform to climb over the Delaware basin. In this area, structural relief of over 19,000 ft over a 10-mi width is believed due to stacking of low-angle thrust sheets. Seismic resolution of this subthrust margin has been complexed by allochtonous hanging-wall gravity-glide blocks and folds and by velocity changes in overlying syn- and posttectonic sediments associated with basin-to-shelf lithofacies changes. Statistical studies indicate that this deep-gas province has a play potential of greater than 10 tcf of gas, with individual prospect sizes exceeding 1 tcfg. The prospects defined along this trend are deep (approximately 20,000 ft) subthrust structural traps that are indigenously sourced and reservoired by dual-matrix porosity. Vitrinite supported maturation modeling suggests that these subthrust structures formed prior to catagenic conversion of the oldest source rocks to oil and later to gas. Tectonically fractured Ordovician Ellenburger and Devonian sediments are considered the principal reservoirs. Shales overlying reservoir intervals form vertical seals.

  2. Reservoir Operations and Flow Modeling to Support Decision Making in the Delaware River Basin

    Science.gov (United States)

    Quinodoz, H. A.

    2006-12-01

    About five percent of the US population depends on the waters from the Delaware River Basin for its water supply, including New York City and Philadelphia. Water management in the basin is governed by a compact signed in 1961 by the four basin states and the federal government. The compact created the Delaware River Basin Commission (DRBC) and gave it broad powers to plan, regulate, and manage the development of the basin water resources. The compact also recognized a pre-existing (1954) U.S. Supreme Court Decree that grants the City of New York the right to export up to 800 million gallons per day out of the basin, provided that a prescribed minimum flow is met at Montague, New Jersey for the use of the lower-basin states. The Delaware River Basin Compact also allows the DRBC to adjust the releases and diversions under the Decree, subject to the unanimous consent of the decree parties. This mechanism has been used several times over the last 30 years, to implement and modify rules governing drought operations, instream flows, minimum flow targets, and control of salinity intrusion. In every case, decision makers have relied upon extensive modeling of alternative proposals, using a basin-wide daily flow model. Often, stakeholders have modified and used the same model to test and refine their proposals prior to consideration by the decision makers. The flow model has been modified over the years, to simulate new features and processes in a river system partially controlled by more than ten reservoirs. The flow model has proved to be an adaptable tool, able to simulate the dynamics of a complex system driven by conflicting objectives. This presentation reviews the characteristics of the daily flow model in its current form, discuss how model simulations are used to inform the decision-making process, and provide a case study of a recent modification of the system-wide drought operating plan.

  3. Records available to September 30, 1956, on use of water in the Delaware Basin Project area

    Science.gov (United States)

    Kammerer, John C.

    1957-01-01

    The purpose of this report is to summarize data on the use of water in the Delaware Basin Project area (fig. 2) and to list the principal data sources that are available in published form. The tables and bibliography will assist Geological Survey personnel assigned to the Delaware Basin Project in evaluating the scope and deficiencies of previous studies of the basin. Information is also given on the use of water by public supplies in the New York-New Jersey region comprising the New York City Metropolitan Area and in the remaining north-central and south-eastern parts of New Jersey. These regions may depend increasingly on water from the Delaware River basin for part of their public supplies. The Geological Survey has the responsibility for appraising and describing the water resources of the Nation as a guide to use, development, control, and conservation of these resources. Cooperative Federal-State water-resources investigations in the Delaware Basin States have been carried on the the Geological Survey for more than 50 years. In July 1956 the Survey began the "Delaware Basin Project," a hydrologic study of the Delaware River basin in order to: 1) Determine present status and trends in water availability, quality, and use, 2) assess and improve the adequacy of the Survey's basic water data program in the basin, 3) interpret and evaluate the water-resources data in terms of past and possible future water-use and land-use practices, and 4) disseminate promptly the results of this investigation for the benefit of all interested agencies and the general public. The Geological Survey is working closely with the U.S. Corps of Engineers and other cooperating Federal and State agencies in providing water data which will contribute to the present coordinated investigation aimed at developing a plan for long-range water development in the Delaware River basin. Estimates of quantities of water used are given for water withdrawn from streams and aquifers during calendar

  4. Groundwater quality in the Delaware and St. Lawrence River Basins, New York, 2010

    Science.gov (United States)

    Nystrom, Elizabeth A.

    2012-01-01

    Water samples were collected from 10 production and domestic wells in the Delaware River Basin in New York and from 20 production and domestic wells in the St. Lawrence River Basin in New York from August through November 2010 to characterize groundwater quality in the basins. The samples were collected and processed by standard U.S. Geological Survey procedures and were analyzed for 147 physiochemical properties and constituents, including major ions, nutrients, trace elements, pesticides, volatile organic compounds (VOCs), radionuclides, and indicator bacteria.

  5. Estimated use of water in the Delaware River Basin in Delaware, New Jersey, New York, and Pennsylvania, 2010

    Science.gov (United States)

    Hutson, Susan S.; Linsey, Kristin S.; Ludlow, Russell A.; Reyes, Betzaida; Shourds, Jennifer L.

    2016-11-07

    The Delaware River Basin (DRB) was selected as a Focus Area Study in 2011 by the U.S. Geological Survey (USGS) as part of the USGS National Water Census. The National Water Census is a USGS research program that focuses on national water availability and use and then develops new water accounting tools and assesses water availability at both the regional and national scales. One of the water management needs that the DRB study addressed, and that was identified by stakeholder groups from the DRB, was to improve the integration of state water use and water-supply data and to provide the compiled water use information to basin users. This water use information was also used in the hydrologic modeling and ecological components of the study.Instream and offstream water use was calculated for 2010 for the DRB based on information received from Delaware, New Jersey, New York, and Pennsylvania. Water withdrawal, interbasin transfers, return flow, and hydroelectric power generation release data were compiled for 11 categories by hydrologic subregion, basin, subbasin, and subwatershed. Data availability varied by state. Site-specific data were used whenever possible to calculate public supply, irrigation (golf courses, nurseries, sod farms, and crops), aquaculture, self-supplied industrial, commercial, mining, thermoelectric, and hydroelectric power withdrawals. Where site-specific data were not available, primarily for crop irrigation, livestock, and domestic use, various techniques were used to estimate water withdrawals.Total water withdrawals in the Delaware River Basin were calculated to be about 7,130 million gallons per day (Mgal/d) in 2010. Calculations of withdrawals by source indicate that freshwater withdrawals were about 4,130 Mgal/d (58 percent of the total) and the remaining 3,000 Mgal/d (42 percent) were from saline water. Total surface-water withdrawals were calculated to be 6,590 Mgal/d, or 92 percent of the total; about 54 percent (3,590 Mgal/d) of surface

  6. Advanced reservoir characterization for improved oil recovery in a New Mexico Delaware basin project

    Energy Technology Data Exchange (ETDEWEB)

    Martin, F.D.; Kendall, R.P.; Whitney, E.M. [Dave Martin and Associates, Inc., Socorro, NM (United States)] [and others

    1997-08-01

    The Nash Draw Brushy Canyon Pool in Eddy County, New Mexico is a field demonstration site in the Department of Energy Class III program. The basic problem at the Nash Draw Pool is the low recovery typically observed in similar Delaware fields. By comparing a control area using standard infill drilling techniques to a pilot area developed using advanced reservoir characterization methods, the goal of the project is to demonstrate that advanced technology can significantly improve oil recovery. During the first year of the project, four new producing wells were drilled, serving as data acquisition wells. Vertical seismic profiles and a 3-D seismic survey were acquired to assist in interwell correlations and facies prediction. Limited surface access at the Nash Draw Pool, caused by proximity of underground potash mining and surface playa lakes, limits development with conventional drilling. Combinations of vertical and horizontal wells combined with selective completions are being evaluated to optimize production performance. Based on the production response of similar Delaware fields, pressure maintenance is a likely requirement at the Nash Draw Pool. A detailed reservoir model of pilot area was developed, and enhanced recovery options, including waterflooding, lean gas, and carbon dioxide injection, are being evaluated.

  7. Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin), Class III

    Energy Technology Data Exchange (ETDEWEB)

    Dutton, Shirley P.; Flanders, William A.

    2001-11-04

    The objective of this Class III project was demonstrate that reservoir characterization and enhanced oil recovery (EOR) by CO2 flood can increase production from slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico. Phase 1 of the project, reservoir characterization, focused on Geraldine Ford and East Ford fields, which are Delaware Mountain Group fields that produce from the upper Bell Canyon Formation (Ramsey sandstone). The demonstration phase of the project was a CO2 flood conducted in East Ford field, which is operated by Orla Petco, Inc., as the East Ford unit.

  8. Estimation of daily mean streamflow for ungaged stream locations in the Delaware River Basin, water years 1960–2010

    Science.gov (United States)

    Stuckey, Marla H.

    2016-06-09

    The ability to characterize baseline streamflow conditions, compare them with current conditions, and assess effects of human activities on streamflow is fundamental to water-management programs addressing water allocation, human-health issues, recreation needs, and establishment of ecological flow criteria. The U.S. Geological Survey, through the National Water Census, has developed the Delaware River Basin Streamflow Estimator Tool (DRB-SET) to estimate baseline (minimally altered) and altered (affected by regulation, diversion, mining, or other anthropogenic activities) and altered streamflow at a daily time step for ungaged stream locations in the Delaware River Basin for water years 1960–2010. Daily mean baseline streamflow is estimated by using the QPPQ method to equate streamflow expressed as a percentile from the flow-duration curve (FDC) for a particular day at an ungaged stream location with the percentile from a FDC for the same day at a hydrologically similar gaged location where streamflow is measured. Parameter-based regression equations were developed for 22 exceedance probabilities from the FDC for ungaged stream locations in the Delaware River Basin. Water use data from 2010 is used to adjust the baseline daily mean streamflow generated from the QPPQ method at ungaged stream locations in the Delaware River Basin to reflect current, or altered, conditions. To evaluate the effectiveness of the overall QPPQ method contained within DRB-SET, a comparison of observed and estimated daily mean streamflows was performed for 109 reference streamgages in and near the Delaware River Basin. The Nash-Sutcliffe efficiency (NSE) values were computed as a measure of goodness of fit. The NSE values (using log10 streamflow values) ranged from 0.22 to 0.98 (median of 0.90) for 45 streamgages in the Upper Delaware River Basin and from -0.37 to 0.98 (median of 0.79) for 41 streamgages in the Lower Delaware River Basin.

  9. Scientific Drilling of the Terrestrial Cretaceous Songliao Basin

    Directory of Open Access Journals (Sweden)

    Terrestrial Scientific Drilling of the Cretaceous Songliao Basin Science Team

    2008-07-01

    Full Text Available Investigations of critical climate changes during the Cretaceous have the potential to enhance our understanding of modern global warming because the extreme variances are the best-known and most recent example of a greenhouse Earth (Bice et al., 2006. Marine Cretaceous climate archives are relatively well explored by scientific ocean drilling programs such as the Integrated Ocean Drilling Program (IODP and its predecessors. However, Cretaceous terrestrial climate records are at best fragmentary (Heimhofer et al., 2005. The long-lived Cretaceous Songliao Basin of NE China is an excellent candidate to fill this gap and provide important ocean-continent linkages in relation to environmental change (Fig. 1. This basin, located within one of the largest Cretaceous landmasses (Scotese, 1988, acted for about 100 million years as an intra-continental sediment trap; the present-day area of the basin is about 260,000 km2. It provides an almost complete terrestrial sedimentary recordfrom the Upper Jurassic to the Paleocene (Chen and Chang, 1994. Large-scale geological and geophysical investigations of lacustrine sediments and basin structures demonstrate that a rich archive of Cretaceous paleoclimate proxies exists. For example, the basin includes the Jehol Biota, a terrestrial response to the Cretaceous oceanic anoxic events (OAEs, and a potential K/T boundary (Qiang et al., 1998. An ongoing drilling program is supported by the Ministry of Science and Technology of China and by the Daqing Oilfield. It allowed for recovering of nearly complete cores from Upper Albian to the Uppermost Cretaceous in two boreholes (SK-I, SK II; commenced in 2006, Fig. 1. However, the older Cretaceous sedimentary record of Songliao Basin has not yet been cored. For that reason, a scientific drilling program has been proposed to the International Continental Scientific Drilling Program (ICDP to sample the deeper sedimentaryrecord of the Songliao Basin through a new drill hole

  10. Dynamic Management of Releases for the Delaware River Basin using NYC's Operations Support Tool

    Science.gov (United States)

    Weiss, W.; Wang, L.; Murphy, T.; Muralidhar, D.; Tarrier, B.

    2011-12-01

    The New York City Department of Environmental Protection (DEP) has initiated design of an Operations Support Tool (OST), a state-of-the-art decision support system to provide computational and predictive support for water supply operations and planning. Using an interim version of OST, DEP and the New York State Department of Environmental Conservation (DEC) have developed a provisional, one-year Delaware River Basin reservoir release program to succeed the existing Flexible Flow Management Program (FFMP) which expired on May 31, 2011. The FFMP grew out of the Good Faith Agreement of 1983 among the four Basin states (New York, New Jersey, Pennsylvania, and Delaware) that established modified diversions and flow targets during drought conditions. It provided a set of release schedules as a framework for managing diversions and releases from New York City's Delaware Basin reservoirs in order to support multiple objectives, including water supply, drought mitigation, flood mitigation, tailwaters fisheries, main stem habitat, recreation, and salinity repulsion. The provisional program (OST-FFMP) defines available water based on current Upper Delaware reservoir conditions and probabilistic forecasts of reservoir inflow. Releases are then set based on a set of release schedules keyed to the water availability. Additionally, OST-FFMP attempts to provide enhanced downstream flood protection by making spill mitigation releases to keep the Delaware System reservoirs at a seasonally varying conditional storage objective. The OST-FFMP approach represents a more robust way of managing downstream releases, accounting for predicted future hydrologic conditions by making more water available for release when conditions are forecasted to be wet and protecting water supply reliability when conditions are forecasted to be dry. Further, the dynamic nature of the program allows the release decision to be adjusted as hydrologic conditions change. OST simulations predict that this

  11. 18 CFR 430.11 - Advance notice of exploratory drilling.

    Science.gov (United States)

    2010-04-01

    ... exploratory drilling. 430.11 Section 430.11 Conservation of Power and Water Resources DELAWARE RIVER BASIN... exploratory drilling. The Commission encourages consultation with any project sponsor who is considering... project and prior to initiation of exploratory drilling. (a) Any person, firm corporation or other...

  12. User’s guide for the Delaware River Basin Streamflow Estimator Tool (DRB-SET)

    Science.gov (United States)

    Stuckey, Marla H.; Ulrich, James E.

    2016-06-09

    IntroductionThe Delaware River Basin Streamflow Estimator Tool (DRB-SET) is a tool for the simulation of streamflow at a daily time step for an ungaged stream location in the Delaware River Basin. DRB-SET was developed by the U.S. Geological Survey (USGS) and funded through WaterSMART as part of the National Water Census, a USGS research program on national water availability and use that develops new water accounting tools and assesses water availability at the regional and national scales. DRB-SET relates probability exceedances at a gaged location to those at an ungaged stream location. Once the ungaged stream location has been identified by the user, an appropriate streamgage is automatically selected in DRB-SET using streamflow correlation (map correlation method). Alternately, the user can manually select a different streamgage or use the closest streamgage. A report file is generated documenting the reference streamgage and ungaged stream location information, basin characteristics, any warnings, baseline (minimally altered) and altered (affected by regulation, diversion, mining, or other anthropogenic activities) daily mean streamflow, and the mean and median streamflow. The estimated daily flows for the ungaged stream location can be easily exported as a text file that can be used as input into a statistical software package to determine additional streamflow statistics, such as flow duration exceedance or streamflow frequency statistics.

  13. Some hydrological impacts of climate change for the Delaware River Basin

    Science.gov (United States)

    Tasker, Gary D.

    1990-01-01

    To gain insight into possible impacts of climate change on water availability in the Delaware River, two models are linked. The first model is a monthly water balance model that converts the temperature and precipitation values generated by a random number generator to monthly streamflow values. The monthly streamflow values are input to a second model that simulates the operation of reservoirs and diversions within the basin. The output for the two linked models consists of time series of reservoir levels and streamflow at key points in the basin. Model results for a base case, in which monthly temperature and precipitation statistics are unchanged from historical records, are compared to several changed-climate scenarios under a standard set of rules of operation.

  14. Sensitivity of water resources in the Delaware River basin to climate variability and change

    Science.gov (United States)

    Ayers, Mark A.; Wolock, David M.; McCabe, Gregory J.; Hay, Lauren E.; Tasker, Gary D.

    1994-01-01

    Because of the greenhouse effect, projected increases in atmospheric carbon dioxide levels might cause global warming, which in turn could result in changes in precipitation patterns and evapotranspiration and in increases in sea level. This report describes the greenhouse effect; discusses the problems and uncertainties associated with the detection, prediction, and effects of climate change; and presents the results of sensitivity analyses of how climate change might affect water resources in the Delaware River basin. Sensitivity analyses suggest that potentially serious shortfalls of certain water resources in the basin could result if some scenarios for climate change come true . The results of model simulations of the basin streamflow demonstrate the difficulty in distinguishing the effects that climate change versus natural climate variability have on streamflow and water supply . The future direction of basin changes in most water resources, furthermore, cannot be precisely determined because of uncertainty in current projections of regional temperature and precipitation . This large uncertainty indicates that, for resource planning, information defining the sensitivities of water resources to a range of climate change is most relevant . The sensitivity analyses could be useful in developing contingency plans for evaluating and responding to changes, should they occur.

  15. Application of advanced reservoir characterization, simulation, and production optimization strategies to maximize recovery in slope and basin clastic reservoirs, West Texas (Delaware Basin), Class III

    Energy Technology Data Exchange (ETDEWEB)

    Dutton, Shirley P.; Flanders, William A.; Zirczy, Helena H.

    2000-05-24

    The objective of this Class 3 project was to demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost effective way to recover a higher percentage of the original oil in place through strategic placement of infill wells and geologically based field development. Phase 1 of the project, reservoir characterization, was completed this year, and Phase 2 began. The project is focused on East Ford field, a representative Delaware Mountain Group field that produces from the upper Bell Canyon Formation (Ramsey sandstone). The field, discovered in 1960, is operated by Oral Petco, Inc., as the East Ford unit. A CO{sub 2} flood is being conducted in the unit, and this flood is the Phase 2 demonstration for the project.

  16. Initial Report on MexiDrill: The Basin of Mexico Drilling Program

    Science.gov (United States)

    Brown, Erik; Werne, Josef; Caballero, Margarita; Cabral, Enrique; Fawcett, Peter; Lozano, Socorro; Morales, Eric; Myrbo, Amy; Noren, Anders; O'Grady, Ryan; Ortega, Beatriz; Perez, Liseth; Schnurrenberger, Doug; Schwalb, Antje; Smith, Victoria; Steinman, Byron; Stockhecke, Mona; Valero, Blas; Watt, Sebastian

    2016-04-01

    The Basin of Mexico (19°30'N, 99°W, 9600 km2, 2240 m asl) is a hydrologically-closed basin in the TransMexican Volcanic Belt. The emergence of the Chichinautzin volcanic field after ~780 ka is linked to basin closure and initiation of the development of a lake system within the basin. Continued subsidence accommodated accumulation of a long lacustrine sediment sequence. Radiocarbon chronologies indicate sedimentation rates of ~40 cm/kyr since ~40ka; application of this rate to the entire lacustrine sequence suggests a basal age of ~800 ka, consistent with the Chichinautzin volcanic age. To investigate the environmental history contained in Basin of Mexico sediments, the MexiDrill Program recovered a long lacustrine sedimentary sequence contained in the Lake Chalco basin on the southern outskirts of Mexico City. These sediments have the potential to provide a >500,000 year record of North American climate. Chalco is well suited for reconstruction and investigation of interannual through orbital-scale variations in the North American Monsoon and hydrologic variations of the neotropics. Ongoing work suggests that the system records environmental responses to both Milankovitch- and millennial-scale climate forcing.

  17. Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin)

    Energy Technology Data Exchange (ETDEWEB)

    Dutton, S.P.; Flanders, W.A.; Guzman, J.I.; Zirczy, H.

    1999-06-08

    The objective of this Class III project is to demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover a higher percentage of the original oil in place through geologically based field development. This year the project focused on reservoir characterization of the East Ford unit, a representative Delaware Mountain Group field that produces from the upper Bell Canyon Formation (Ramsey Sandstone). The field, discovered in 1960, is operated by Orla Petco, Inc., as the East Ford unit; it contained an estimated 19.8 million barrels (MMbbl) of original oil in place. Petrophysical characterization of the East Ford unit was accomplished by integrating core and log data and quantifying petrophysical properties from wireline logs. Most methods of petrophysical analysis that had been developed during an earlier study of the Ford Geraldine unit were successfully transferred to the East Ford unit. The approach that was used to interpret water saturation from resistivity logs, however, had to be modified because in some East Ford wells the log-calculated water saturation was too high and inconsistent with observations made during the actual production. Log-porosity to core-porosity transforms and core-porosity to core-permeability transforms were derived from the East Ford reservoir. The petrophysical data were used to map porosity, permeability, net pay, water saturation, mobil-oil saturation, and other reservoir properties.

  18. Effects of climatic change and climatic variability on the Thornthwaite moisture index in the Delaware River basin

    Science.gov (United States)

    McCabe, G.J.; Wolock, D.M.

    1992-01-01

    The Thornthwaite moisture index is useful as an indicator of the supply of water in an area relative to the demand under prevailing climatic conditions. This study examines the effects of long-term changes in climate (temperature and precipitation) on the Thornthwaite moisture index in the Delaware River basin. Temperature and precipitation estimates for doubled-CO2 conditions derived from three general circulation models (GCMs) are used to study the response of the moisture index for steady-state doubled-CO2 conditions and for gradual changes from present to doubled-CO2 conditions. Results of the study indicate that temperature and precipitation under doubled-CO2 conditions will cause the Thornthwaite moisture index to decrease, implying significantly drier conditions in the Delaware River basin than currently exist. The amount of decrease depends, however, on the GCM climatic-change scenario used. The results also indicate that future changes in the moisture index will be partly masked by natural year-to-year variability in temperature and precipitation. ?? 1992 Kluwer Academic Publishers.

  19. Ground-Water Quality in the Delaware River Basin, New York, 2001 and 2005-2006

    Science.gov (United States)

    Nystrom, Elizabeth A.

    2007-01-01

    The Federal Clean Water Act Amendments of 1977 require that States monitor and report on the quality of ground water and surface water. To satisfy part of these requirements, the U.S. Geological Survey and New York State Department of Environmental Conservation have developed a program in which ground-water quality is assessed in 2 to 3 of New York State's 14 major basins each year. To characterize the quality of ground water in the Delaware River Basin in New York, water samples were collected from December 2005 to February 2006 from 10 wells finished in bedrock. Data from 9 samples collected from wells finished in sand and gravel in July and August 2001 for the National Water Quality Assessment Program also are included. Ground-water samples were collected and processed using standard U.S. Geological Survey procedures. Samples were analyzed for more than 230 properties and compounds, including physical properties, major ions, nutrients, trace elements, radon-222, pesticides and pesticide degradates, volatile organic compounds, and bacteria. Concentrations of most compounds were less than drinking-water standards established by the U.S. Environmental Protection Agency and New York State Department of Health; many of the organic analytes were not detected in any sample. Drinking-water standards that were exceeded at some sites include those for color, turbidity, pH, aluminum, arsenic, iron, manganese, radon-222, and bacteria. pH ranged from 5.6 to 8.3; the pH of nine samples was less than the U.S. Environmental Protection Agency secondary drinking-water standard range of 6.5 to 8.5. Water in the basin is generally soft to moderately hard (hardness 120 milligrams per liter as CaCO3 or less). The cation with the highest median concentration was calcium; the anion with the highest median concentrations was bicarbonate. Nitrate was the predominant nutrient detected but no sample exceeded the 10 mg/L U.S. Environmental Protection Agency maximum contaminant level. The

  20. Climate change effects on forests, water resources, and communities of the Delaware River Basin

    Science.gov (United States)

    Will Price; Susan Beecher

    2014-01-01

    The Delaware River provides drinking water to 5 percent of the United States, or approximately 16.2 million people living in 4 states, 42 counties, and over 800 municipalities. The more than 1.5 billion gallons withdrawn or diverted daily for drinking water is delivered by more than 140 purveyors, yet constitutes less than 20 percent of the average daily withdrawals....

  1. Organic Compounds and Trace Elements in Fish Tissue and Bed Sediment in the Delaware River Basin, New Jersey, Pennsylvania, New York, and Delaware, 1998-2000

    Science.gov (United States)

    Romanok, Kristin M.; Fischer, Jeffrey M.; Riva-Murray, Karen; Brightbill, Robin; Bilger, Michael

    2006-01-01

    As part of the National Water-Quality Assessment (NAWQA) program activities in the Delaware River Basin (DELR), samples of fish tissue from 21 sites and samples of bed sediment from 35 sites were analyzed for a suite of organic compounds and trace elements. The sampling sites, within subbasins ranging in size from 11 to 600 square miles, were selected to represent 5 main land-use categories in the DELR -forest, low-agricultural, agricultural, urban, and mixed use. Samples of both fish tissue and bed sediment were also collected from 4 'large-river' sites that represented drainage areas ranging from 1,300 to 6,800 square miles, areas in which the land is used for a variety of purposes. One or more of the organochlorine compounds-DDT and chlordane metabolites, polychlorinated biphenyls (total PCBs), and dieldrin- were detected frequently in samples collected over a wide geographic area. One or more of these compounds were detected in fish-tissue samples from 92 percent of the sites and in bed-sediment samples from 82 percent of the sites. Concentrations of total DDT, total chlordanes, total PCBs, and dieldrin in whole white suckers and in bed sediment were significantly related to urban/industrial basin characteristics, such as percentage of urban land use and population density. Semi-volatile organic compounds (SVOCs)-total polycyclic aromatic hydrocarbons (PAHs), total phthalates, and phenols- were detected frequently in bed-sediment samples. All three types of SVOCs were detected in samples from at least one site in each land-use category. The highest detection rates and concentrations typically were in samples from sites in the urban and mixed land-use categories, as well as from the large-river sites. Concentrations of total PAHs and total phthalates in bed-sediment samples were found to be statistically related to percentages of urban land use and to population density in the drainage areas represented by the sampling sites. The samples of fish tissue and bed

  2. Role of sea-level change in deep water deposition along a carbonate shelf margin, Early and Middle Permian, Delaware Basin: implications for reservoir characterization

    Science.gov (United States)

    Li, Shunli; Yu, Xinghe; Li, Shengli; Giles, Katherine A.

    2015-04-01

    The architecture and sedimentary characteristics of deep water deposition can reflect influences of sea-level change on depositional processes on the shelf edge, slope, and basin floor. Outcrops of the northern slope and basin floor of the Delaware Basin in west Texas are progressively exposed due to canyon incision and road cutting. The outcrops in the Delaware Basin were measured to characterize gravity flow deposits in deep water of the basin. Subsurface data from the East Ford and Red Tank fields in the central and northeastern Delaware Basin were used to study reservoir architectures and properties. Depositional models of deep water gravity flows at different stages of sea-level change were constructed on the basis of outcrop and subsurface data. In the falling-stage system tracts, sandy debris with collapses of reef carbonates are deposited on the slope, and high-density turbidites on the slope toe and basin floor. In the low-stand system tracts, deep water fans that consist of mixed sand/mud facies on the basin floor are comprised of high- to low-density turbidites. In the transgression and high-stand system tracts, channel-levee systems and elongate lobes of mud-rich calciturbidite deposits formed as a result of sea level rise and scarcity of sandy sediment supply. For the reservoir architecture, the fan-like debris and high-density turbidites show high net-to-gross ratio of 62 %, which indicates the sandiest reservoirs for hydrocarbon accumulation. Lobe-like deep water fans with net-to-gross ratio of 57 % facilitate the formation of high quality sandy reservoirs. The channel-levee systems with muddy calciturbidites have low net-to-gross ratio of 30 %.

  3. Results of the marine biota monitoring during drilling activity on Campos Basin, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Petta, Claudia Brigagao de; Bastos, Fabio; Danielski, Monica; Ferreira, Mariana; Gama, Mariana; Coelho, Ana Paula Athanazio; Maia, Decio [Aecom do Brasil Ltda, Rio de Janeiro, RJ (Brazil)

    2012-07-01

    The Environmental Monitoring Project (PMA) aims to report environmental changes arising from drilling activity, in relation to the marine fauna. This project can also help in the monitoring of accidental spills. Since the professionals spend six hours of the day monitoring the ocean around the rigs, they can locate and identify oil stains, notify the responsible onboard, and also help in the monitoring of the oil stain. Such Project has been developed onboard a drilling unit working in Campos Basin. The results presented here were collected during the drilling activity in Bijupira and Salema fields, by Shell Brasil Petroleo Ltda, from July 13th to October 8th, 2011.

  4. Field guide to Laramide basin evolution and drilling activity in North Park and Middle Park, Colorado

    Science.gov (United States)

    Dechesne, Marieke; Cole, James Channing; Martin, Christopher B.

    2016-01-01

    Overview of the geologic history of the North Park–Middle Park area and its past and recent drilling activity. Field trip stops highlight basin formation and the consequences of geologic configuration on oil and gas plays and development. The starting point is the west flank of the Denver Basin to compare and contrast the latest Cretaceous through Eocene basin fill on both flanks of the Front Range, before exploring sediments of the same age in the North Park – Middle Park intermontane basin.

  5. Summary of hydrologic modeling for the Delaware River Basin using the Water Availability Tool for Environmental Resources (WATER)

    Science.gov (United States)

    Williamson, Tanja N.; Lant, Jeremiah G.; Claggett, Peter; Nystrom, Elizabeth A.; Milly, Paul C.D.; Nelson, Hugh L.; Hoffman, Scott A.; Colarullo, Susan J.; Fischer, Jeffrey M.

    2015-11-18

    The Water Availability Tool for Environmental Resources (WATER) is a decision support system for the nontidal part of the Delaware River Basin that provides a consistent and objective method of simulating streamflow under historical, forecasted, and managed conditions. In order to quantify the uncertainty associated with these simulations, however, streamflow and the associated hydroclimatic variables of potential evapotranspiration, actual evapotranspiration, and snow accumulation and snowmelt must be simulated and compared to long-term, daily observations from sites. This report details model development and optimization, statistical evaluation of simulations for 57 basins ranging from 2 to 930 km2 and 11.0 to 99.5 percent forested cover, and how this statistical evaluation of daily streamflow relates to simulating environmental changes and management decisions that are best examined at monthly time steps normalized over multiple decades. The decision support system provides a database of historical spatial and climatic data for simulating streamflow for 2001–11, in addition to land-cover and general circulation model forecasts that focus on 2030 and 2060. WATER integrates geospatial sampling of landscape characteristics, including topographic and soil properties, with a regionally calibrated hillslope-hydrology model, an impervious-surface model, and hydroclimatic models that were parameterized by using three hydrologic response units: forested, agricultural, and developed land cover. This integration enables the regional hydrologic modeling approach used in WATER without requiring site-specific optimization or those stationary conditions inferred when using a statistical model.

  6. Shallow gas well drilling with coiled tubing in the San Juan Basin

    Energy Technology Data Exchange (ETDEWEB)

    Moon, R.G.; Ovitz, R.W.; Guild, G.J.; Biggs, M.D.

    1996-12-31

    Coiled tubing is being utilized to drill new wells, for re-entry drilling to deepen or laterally extend existing wells, and for underbalanced drilling to prevent formation damage. Less than a decade old, coiled tubing drilling technology is still in its inaugral development stage. Initially, utilizing coiled tubing was viewed as a {open_quotes}science project{close_quotes} to determine the validity of performing drilling operations in-lieu of the conventional rotary rig. Like any new technology, the initial attempts were not always successful, but did show promise as an economical alternative if continued efforts were made in the refinement of equipment and operational procedures. A multiwell project has been completed in the San Juan Basin of Northwestern New Mexico which provides documentation indicating that coiled tubing can be an alternative to the conventional rotary rig. A 3-well pilot project, a 6-well project was completed uniquely utilizing the combined resources of a coiled tubing service company, a producing company, and a drilling contractor. This combination of resources aided in the refinement of surface equipment, personnel, mud systems, jointed pipe handling, and mobilization. The results of the project indicate that utilization of coiled tubing for the specific wells drilled was an economical alternative to the conventional rotary rig for drilling shallow gas wells.

  7. Drill hole data for coal beds in the Powder River Basin, Montana and Wyoming

    Science.gov (United States)

    Haacke, Jon E.; Scott, David C.

    2013-01-01

    This report by the U.S. Geological Survey (USGS) of the Powder River Basin (PRB) of Montana and Wyoming is part of the U.S. Coal Resources and Reserves Assessment Project. Essential to that project was the creation of a comprehensive drill hole database that was used for coal bed correlation and for coal resource and reserve assessments in the PRB. This drill hole database was assembled using data from the USGS National Coal Resources Data System, several other Federal and State agencies, and selected mining companies. Additionally, USGS personnel manually entered lithologic picks into the database from geophysical logs of coalbed methane, oil, and gas wells. Of the 29,928 drill holes processed, records of 21,393 are in the public domain and are included in this report. The database contains location information, lithology, and coal bed names for each drill hole.

  8. Bridging the GAPS from Space: A Research/Educational Partnership in the Upper Delaware River Basin

    Science.gov (United States)

    Brown de Colstoun, E.; Robin, J.; Minelli, S.; Katsaros, M.; Peterec, I.; Sandt, K.

    2006-05-01

    The National Park Service (NPS) Inventory and Monitoring (I&M) Program is currently developing scientific protocols to inventory and monitor the natural resources of 270 park units at the national level. These are aimed at providing critical tools needed by park managers for effective decision-making regarding the management and stewardship of the resources they are charged with protecting. We are currently developing a satellite-based regional land cover and land use monitoring protocol that addresses the immediate needs of the NPS I&M. This is a pilot project that examines land cover/use changes in and around the Upper Delaware Scenic and Recreational River and Delaware Water Gap National Recreation Area national parks from Landsat data for the period 1984 to 2005, in one the fastest growing regions in the country. The products resulting from the application of the protocols are then used to guide the simulation of land cover/use changes within a simple Soil-Vegetation-Atmosphere-Transfer (SVAT) model called GAPS in order to better understand the consequences of the measured land cover/use change on the water and energy cycles of the parks and surrounding areas. The data needed for product validation and model parameterization are being acquired with the assistance of students and educators from area schools using protocols established through the GLOBE program. Through focused workshops organized in collaboration with NPS educational specialists and PA regional educational service agencies called Intermediate Units, and participation in hands-on field measurement campaigns, students and educators are learning about satellite remote sensing interpretation, land cover classification, and how to measure/monitor changes in land cover/use in their communities. Students will also assist in the model simulations using the data they acquire in the field. This partnership between the Principal Investigator, the NPS, Intermediate Units and area students and educators is

  9. Well successfully drilled with high performance water-based fluid: Santos Basins, offshore Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Fornasier, Frank C.; Luzardo, Juan P. [Halliburton Company, Houston, TX (United States); Bishnoi, M.L. [Oil and Natural Gas Corporation Ltda. (ONGC), Dehradun (India)

    2012-07-01

    Santos Basin is a 352,260 square kilometers (136,010 sq mi) offshore pre-salt basin. It is located in the South Atlantic Ocean, some 300 kilometers (190 mi) South East of Sao Paulo, Brazil. One of the largest Brazilian sedimentary basins, it is the site of several recent significant oil fields, including Tupi and Jupiter. The criteria for drilling fluid selection is based upon the following factors: maximum cost efficiency, environmental friendliness, optimum borehole stability, and ease of use. The recommended drilling fluid formulation takes into consideration the experience gained during the drilling of wells in the Santos Basin area. The operator wanted to use a high-performance water-based fluid (HPWBF) that could provide shale inhibition, wellbore stability, lubricity and improved rate of penetration (ROP) as an alternative to synthetic-based drilling fluids to present value in terms of economics and environmental friendliness. The HPWBF consists of three synergistic products: a hydration suppressant, a dispersion suppressant, and an accretion suppressant. The system is formulated based on customized solutions for managing the clay reactivity. High logistics costs require drilling fluids that can be prepared with sea water and discharged to the sea without environmental impact. The HPWBF is a clay-free system designed for maximum shale inhibition in highly reactive formations. The system can provide wellbore stability, high rates of penetration, and acceptable rheological properties over a wide range of temperatures, with the added benefit of allowing cuttings discharge based upon water base environmental restrictions. Since no oil is used in the formulation, the HPWBF eliminates the need for cuttings processing and monitoring equipment, and exceeds the environmental requirements by achieving an LC50 value of 345,478.22 ppm in comparison with the minimum requirement (LC50 > 30,000 ppm in 96 hr), permitting use and discharge to the sea. The HPWBF selected

  10. Evaluating methods to establish habitat suitability criteria: A case study in the upper Delaware River Basin, USA

    Science.gov (United States)

    Galbraith, Heather S.; Blakeslee, Carrie J.; Cole, Jeffrey C.; Talbert, Colin; Maloney, Kelly O.

    2016-01-01

    Defining habitat suitability criteria (HSC) of aquatic biota can be a key component to environmental flow science. HSC can be developed through numerous methods; however, few studies have evaluated the consistency of HSC developed by different methodologies. We directly compared HSC for depth and velocity developed by the Delphi method (expert opinion) and by two primary literature meta-analyses (literature-derived range and interquartile range) to assess whether these independent methods produce analogous criteria for multiple species (rainbow trout, brown trout, American shad, and shallow fast guild) and life stages. We further evaluated how these two independently developed HSC affect calculations of habitat availability under three alternative reservoir management scenarios in the upper Delaware River at a mesohabitat (main channel, stream margins, and flood plain), reach, and basin scale. In general, literature-derived HSC fell within the range of the Delphi HSC, with highest congruence for velocity habitat. Habitat area predicted using the Delphi HSC fell between the habitat area predicted using two literature-derived HSC, both at the basin and the site scale. Predicted habitat increased in shallow regions (stream margins and flood plain) using literature-derived HSC while Delphi-derived HSC predicted increased channel habitat. HSC generally favoured the same reservoir management scenario; however, no favoured reservoir management scenario was the most common outcome when applying the literature range HSC. The differences found in this study lend insight into how different methodologies can shape HSC and their consequences for predicted habitat and water management decisions. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

  11. Engineering report on drilling in the Sand Wash Basin, Colorado. [In support of NURE program

    Energy Technology Data Exchange (ETDEWEB)

    Callihan, M C

    1980-01-01

    The Sand Wash Basin Drilling project was conducted by Bendix Field Engineering Corporation in support of the US Department of Energy (DOE) National Uranium Resource Evaluation (NURE) program. This project consisted of 27 drill holes ranging in depth from 110 feet (33.5 m) to 1,995 feet (608.1 m). A total of 25,514 feet (7,471.9 m) was rotary drilled, and 1,593.5 feet (485.7 m) were cored resulting in a total of 26,107.5 feet (7,957.6 m) drilled for the project. The objective of the project was to provide comprehensive subsurface geologic data relevant to uranium mineralization. This was accomplished by drilling in major outcrop areas of the Browns Park Formation in Moffat and Routt Counties, Colorado. The project began May 18, 1979; drilling was completed November 4, 1979. Most site restoration and cleanup was completed during the fall of 1979 with the remainder to be completed during the spring of 1980.

  12. Hydrothermal alteration in research drill hole Y-3, Lower Geyser Basin, Yellowstone National Park, Wyoming

    Science.gov (United States)

    Bargar, Keith E.; Beeson, Melvin H.

    1985-01-01

    Y-3, a U.S. Geological Survey research diamond-drill hole in Lower Geyser Basin, Yellowstone National Park, Wyoming, reached a depth of 156.7 m. The recovered drill core consists of 42.2 m of surficial (mostly glacial) sediments and two rhyolite flows (Nez Perce Creek flow and an older, unnamed rhyolite flow) of the Central Plateau Member of the Pleistocene Plateau Rhyolite. Hydrothermal alteration is fairly extensive in most of the drill core. The surficial deposits are largely cemented by silica and zeolite minerals; and the two rhyolite flows are, in part, bleached by thermal water that deposited numerous hydrothermal minerals in cavities and fractures. Hydrothermal minerals containing sodium as a dominant cation (analcime, clinoptilolite, mordenite, Na-smectite, and aegirine) are more abundant than calcium-bearing minerals (calcite, fluorite, Ca-smectite, and pectolite) in the sedimentary section of the drill core. In the volcanic section of drill core Y-3, calcium-rich minerals (dachiardite, laumontite, yugawaralite, calcite, fluorite, Ca-smectite, pectolite, and truscottite) are predominant over sodium-bearing minerals (aegirine, mordenite, and Na-smectite). Hydrothermal minerals that contain significant amounts of potassium (alunite and lepidolite in the sediments and illitesmectite in the rhyolite flows) are found in the two drill-core intervals. Drill core y:.3 also contains hydrothermal silica minerals (opal, [3-cristobalite, chalcedony, and quartz), other clay minerals (allophane, halloysite, kaolinite, and chlorite), gypsum, pyrite, and hematite. The dominance of calcium-bearing hydrothermal minerals in the lower rhyolitic section of the y:.3 drill core appears to be due to loss of calcium, along with potassium, during adiabatic cooling of an ascending boiling water.

  13. Pathogenic bacteria and microbial-source tracking markers in Brandywine Creek Basin, Pennsylvania and Delaware, 2009-10

    Science.gov (United States)

    Duris, Joseph W.; Reif, Andrew G.; Olson, Leif E.; Johnson, Heather E.

    2011-01-01

    The City of Wilmington, Delaware, is in the downstream part of the Brandywine Creek Basin, on the main stem of Brandywine Creek. Wilmington uses this stream, which drains a mixed-land-use area upstream, for its main drinking-water supply. Because the stream is used for drinking water, Wilmington is in need of information about the occurrence and distribution of specific fecally derived pathogenic bacteria (disease-causing bacteria) and their relations to commonly measured fecal-indicator bacteria (FIB), as well as information regarding the potential sources of the fecal pollution and pathogens in the basin. This study focused on five routinely sampled sites within the basin, one each on the West Branch and the East Branch of Brandywine Creek and at three on the main stem below the confluence of the West and East Branches. These sites were sampled monthly for 1 year. Targeted event samples were collected on two occasions during high flow and two occasions during normal flow. On the basis of this study, high flows in the Brandywine Creek Basin were related to increases in FIB densities, and in the frequency of selected pathogen and source markers, in the West Branch and main stem of Brandywine Creek, but not in the East Branch. Water exceeding the moderate fullbody-contact single-sample recreational water-quality criteria (RWQC) for Escherichia coli (E. coli) was more likely to contain selected markers for pathogenic E. coli (eaeA,stx1, and rfbO157 gene markers) and bovine fecal sources (E. hirae and LTIIa gene markers), whereas samples exceeding the enterococci RWQC were more likely to contain the same pathogenic markers but also were more likely to carry a marker indicative of human source (esp gene marker). On four sample dates, during high flow between October and March, the West Branch was the only observed potential contributor of selected pathogen and bovine source markers to the main stem of Brandywine Creek. Indeed, the stx2 marker, which indicates a highly

  14. Application of advanced reservoir characterization, simulation, and production optimization strategies to maximize recovery in slope and basin clastic reservoirs, west Texas (Delaware Basin). Annual progress report, March 31, 1995--March 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Dutton, S.P.; Hovorka, S.D.; Cole, A.G.

    1996-08-01

    The objective of this Class III project is to demonstrate that detailed reservoir characterization of clastic reservoirs in basinal sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover more of the original oil in place by strategic infill-well placement and geologically based field development. Reservoirs in the Delaware Mountain Group have low producibility (average recovery <14 percent of the original oil in place) because of a high degree of vertical and lateral heterogeneity caused by depositional processes and post-depositional diagenetic modification. Detailed correlations of the Ramsey sandstone reservoirs in Geraldine Ford field suggest that lateral sandstone continuity is less than interpreted by previous studies. The degree of lateral heterogeneity in the reservoir sandstones suggests that they were deposited by eolian-derived turbidites. According to the eolian-derived turbidite model, sand dunes migrated across the exposed shelf to the shelf break during sea-level lowstands and provided well sorted sand for turbidity currents or grain flows into the deep basin.

  15. Modeling forest carbon and nitrogen cycles based on long term carbon stock field measurement in the Delaware River Basin

    Science.gov (United States)

    Xu, B.; Pan, Y.; McCullough, K.; Plante, A. F.; Birdsey, R.

    2015-12-01

    Process-based models are a powerful approach to test our understanding of biogeochemical processes, to extrapolate ground survey data from limited plots to the landscape scale and to simulate the effects of climate change, nitrogen deposition, elevated atmospheric CO2, increasing natural disturbances and land use change on ecological processes. However, in most studies, the models are calibrated using ground measurements from only a few sites, though they may be extrapolated to much larger areas. Estimation accuracy can be improved if the models are parameterized using long-term carbon stock data from multiple sites representative of the simulated region. In this study, vegetation biomass and soil carbon stocks, and changes in these stocks over a recent decade, were measured in 61 forested plots located in three small watersheds in the Delaware River Basin (DRB). On average, total vegetation biomass was 160.2 Mg C ha-1 and the soil carbon stock was 76.6 Mg C ha-1, measured during 2012-2014. The biomass carbon stock increased by 2.45 Mg C ha-1 yr-1 from 2001-2003 to 2012-2014. This dataset was subsequently used to parameterize the PnET-CN model at the individual plot basis, and averaged parameters among plots were then applied to generate new watershed-scale model parameters for each of the three watersheds. The parameterized model was further validated by the field measurements in each of the major forest types. The spatial distribution of forest carbon pools and fluxes in three watersheds were mapped based on the simulation results from the newly parameterized PnET-CN model. The model will also be run under different scenarios to test the effects of climate change, altered atmospheric composition, land use change, and their interactions within the three watersheds and across the whole DRB.

  16. Assessing potential impacts of a wastewater rapid infiltration basin system on groundwater quality: a delaware case study.

    Science.gov (United States)

    Andres, A S; Sims, J Thomas

    2013-01-01

    Rapid infiltration basin systems (RIBS) are receiving increased interest for domestic wastewater disposal in rural areas. They rely on natural treatment processes to filter pollutants and use extremely high effluent loading rates, much greater than natural precipitation, applied to a small geographic area instead of disposal to surface water. Concerns exist today that adopting RIBS in areas with shallow groundwater and sandy soils may increase ground and surface water pollution. We conducted a field study of RIBS effects on N and P concentrations in soils and groundwater at Cape Henlopen State Park, Delaware, where a RIBS designed and operated following USEPA guidance has been used for >25 yr. Site and wastewater characteristics (water table of 8 m, Fe- and Al-oxide coatings on soils, organic-rich effluent) were favorable for denitrification and P sorption; however, we found high P saturation, reduced soil P sorption capacity, and significant total P accumulation at depths >1.5 m, factors that could lead to dissolved P leaching. Very low soil inorganic N levels suggest that wastewater N was converted rapidly to NO-N and leached from the RIBS. Extensive groundwater monitoring supported these concerns and showed rapid offsite transport of N and P at concentrations similar to the effluent. Results suggest that high hydraulic loads and preferential flow led to flow velocities that were too large, and contact times between effluent and soils that were too short, for effective N and P attenuation processes. These findings indicate the need for better site characterization and facility designs to reduce and monitor contaminant loss from RIBS in similar settings. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  17. Uncertainties in forest soil carbon and nitrogen estimates related to soil sampling methods in the Delaware River Basin

    Science.gov (United States)

    Xu, B.; Plante, A. F.; Johnson, A. H.; Pan, Y.

    2014-12-01

    Estimating forest soil carbon and nitrogen (CN) is critical to understanding ecosystem responses to changing climate, disturbance and forest management practices. Most of the uncertainty in soil CN cycling is associated with the difficulty in characterizing soil properties in field sampling because forest soils can be rocky, inaccessible and spatially heterogeneous. A composite coring technique is broadly applied as the standard FIA soil sampling protocol. However, the accuracy of this method might be limited by soil compaction, rock obstruction and plot selection problems during sampling. In contrast, the quantitative soil pit sampling method may avoid these problems and provides direct measurements of soil mass, rock volume and CN concentration representative of a larger ground surface area. In this study, the two sampling methods were applied in 60 forest plots, randomly located in three research areas in the Delaware River Basin in the U.S. Mid-Atlantic region. In each of the plots, one quantitative soil pit was excavated and three soil cores were collected. Our results show that average soil bulk density in the top 20 cm mineral soil measured from the soil cores was consistently lower than bulk density measured by soil pits. However, the volume percentage of coarse fragments measured by the core method was also significantly lower than the pit method. Conversely, CN concentrations were greater in core samples compared to pit samples. The resulting soil carbon content (0-20 cm) was estimated to be 4.1 ± 0.4 kg m-2 in the core method compared to 4.5 ± 0.4 kg m-2 in the pit method. Lower bulk density but higher CN concentration and lower coarse fragments content from the cores have offset each other, resulting in no significant differences in CN content from the soil pit method. Deeper soil (20-40 cm), which is not accessible in the core method, accounted for 29% of the total soil carbon stock (0-40 cm) in the pit method. Our results suggest that, although soil

  18. Delaware Bay, Delaware Benthic Habitats 2010 Biotic

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Coastal Program of Delaware's Division of Soil and Water conservation (DNREC), the University of Delaware, Partnership for the Delaware Estuary, and the New...

  19. Delaware Bay, Delaware Benthic Grabs 2007

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Coastal Program of Delaware's Division of Soil and Water conservation (DNREC), the University of Delaware, Partnership for the Delaware Estuary, and the New...

  20. Delaware Bay, Delaware Benthic Habitats 2010 Geodatabase

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Coastal Program of Delaware's Division of Soil and Water conservation (DNREC), the University of Delaware, Partnership for the Delaware Estuary, and the New...

  1. Delaware Bay, Delaware Benthic Habitats 2010 Substrate

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Coastal Program of Delaware's Division of Soil and Water conservation (DNREC), the University of Delaware, Partnership for the Delaware Estuary, and the New...

  2. Delaware Bay, Delaware Benthic Habitats 2010 Geoform

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Coastal Program of Delaware's Division of Soil and Water conservation (DNREC), the University of Delaware, Partnership for the Delaware Estuary, and the New...

  3. Relation of water quality to land use in the drainage basins of six tributaries to the lower Delaware River, New Jersey, 2002-07

    Science.gov (United States)

    Baker, Ronald J.; Esralew, Rachel A.

    2010-01-01

    Concentrations and loads of water-quality constituents in six streams in the lower Delaware River Basin of New Jersey were determined in a multi-year study conducted by the U.S. Geological Survey, in cooperation with the New Jersey Department of Environmental Protection. Two streams receive water from relatively undeveloped basins, two from largely agricultural basins, and two from heavily urbanized basins. Each stream was monitored during eight storms and at least eight times during base flow during 2002-07. Sampling was conducted during base flow before each storm, when stage was first observed to rise, and several times during the rising limb of the hydrographs. Agricultural and urban land use has resulted in statistically significant increases in loads of nitrogen and phosphorus species relative to loads in undeveloped basins. For example, during the growing season, median storm flow concentrations of total nitrogen in the two streams in agricultural areas were 6,290 and 1,760 mg/L, compared to 988 and 823 mg/L for streams in urban areas, and 719 and 333 mg/L in undeveloped areas. Although nutrient concentrations and loads were clearly related to land useurban, agricultural, and undeveloped within the drainage basins, other basin characteristics were found to be important. Residual nutrients entrapped in lake sediments from streams that received effluent from recently removed sewage-treatment plants are hypothesized to be the cause of extremely high levels of nutrient loads to one urban stream, whereas another urban stream with similar land-use percentages (but without the legacy of sewage-treatment plants) had much lower levels of nutrients. One of the two agricultural streams studied had higher nutrient loads than the other, especially for total phosphorous and organic nitrogen. This difference appears to be related to the presence (or absence) of livestock (cattle).

  4. Drill bit seismic, vertical seismic profiling, and seismic depth imaging to acid drilling decisions in the Tho Tinh structure Nam Con Son Basin-Vietnam

    Energy Technology Data Exchange (ETDEWEB)

    Borland, W.; Leaney, W.; Nakanishi, S.; Kusaka, H.

    1998-02-01

    Rapid deposition in the Nam Con Son Basin during the Miocene resulted in under-compacted shales. These under-compacted shales are often associated with over-pressured formations. As these shales have excess water and tend to be mechanically weak, the safe mud window for drilling the under-compacted interval can be quite narrow. Efficient and safe drilling operations require accurate depth predictions of these over-pressured formations as well a knowledge of the magnitude of the over-pressure. In this paper we describe a technique which combines the best aspects of conventional Vertical Seismic Profiles (VSP) and Reverse Vertical Seismic Profiles (RVSP) to detect under-compacted shales and predict formation pressures to locate drilling hazards below TD. Under-compacted shales with excess water will have a lower acoustic impedance than expected from the compaction trend. Shales that depart from the compaction trend may indicate potential drilling hazards below. Conventional VSPs provide high quality reflection data at discrete intervals in the well, and can be used to accurately predict acoustic impedance below the bit. This acoustic impedance is then interpreted to provide both the location (in time and depth) of the drilling hazard and the mud weight necessary to contain it. The two-way time estimate of the hazard location is usually quite accurate but the depth estimate is less certain due to the estimation error in formation velocities below TD. The RVSP using the drill bit as a source, provides a continuous time versus depth relationship while drilling. This time versus depth is used to continually update the conventional VSP depth prediction of the drilling hazard and thus provide the most accurate depth of the hazard prior to its penetration. It is also used to update a depth-indexed display of existing surface seismic at the wellsite. 10 refs., 22 figs.

  5. Delaware River Basin

    Science.gov (United States)

    Fischer, Jeffrey M.

    1999-01-01

    During the past 25 years, industry and government have made large financial investments in manufacturing, processing, and wastewater-treatment facilities to reduce the amount of contaminants being discharged. Although these investments have led to improved water quality across the Nation, concerns about the effects of nutrients, toxins, and pathogens on human health and that of ecological communities remain. To address the need for consistent and scientifically sound information for managing the Nation's water resources, the U.S. Geological Survey began the National Water-Quality Assessment (NAWQA) program in 1991. This program is unique in that it integrates surface- and ground-water-quality monitoring with the study of aquatic ecosystems. The goals of the NAWQA program are to (1) describe current water-quality conditions for a large part of the Nation's freshwater streams and aquifers (water-bearing sediments and rocks), (2) describe how water quality is changing over time, and (3) increase our understanding of the natural and human factors that affect water quality (Leahy and others, 1990, Gilliom and others, 1995).

  6. Invasive Species Guidebook for Department of Defense Installations in the Delaware River Basin: Identification, Control, and Restoration

    Science.gov (United States)

    2009-06-01

    wildflowers and their related organisms. Fig buttercup’s early growth period allows it to become well established before native spring plants begin...pest of waterways from coastal Virginia to Florida and west to Texas, with a disjunct population in California . It exhibits both aquatic and...University of California -Davis database, and Washington State Department of Ecology. 112 INVASIVE SPECIES GUIDEBOOK FOR DOD INSTALLATIONS IN THE DELAWARE

  7. Geologic Characterization of Young Alluvial Basin-Fill Deposits from Drill Hole Data in Yucca Flat, Nye County, Nevada.

    Energy Technology Data Exchange (ETDEWEB)

    Donald S. Sweetkind; Ronald M. Drake II

    2007-01-22

    Yucca Flat is a topographic and structural basin in the northeastern part of the Nevada Test Site (NTS) in Nye County, Nevada, that has been the site of numerous underground nuclear tests; many of these tests occurred within the young alluvial basin-fill deposits. The migration of radionuclides to the Paleozoic carbonate aquifer involves passage through this thick, heterogeneous section of Tertiary and Quaternary rock. An understanding of the lateral and vertical changes in the material properties of young alluvial basin-fill deposits will aid in the further development of the hydrogeologic framework and the delineation of hydrostratigraphic units and hydraulic properties required for simulating ground-water flow in the Yucca Flat area. This report by the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, presents data and interpretation regarding the three-dimensional variability of the shallow alluvial aquifers in areas of testing at Yucca Flat, data that are potentially useful in the understanding of the subsurface flow system. This report includes a summary and interpretation of alluvial basin-fill stratigraphy in the Yucca Flat area based on drill hole data from 285 selected drill holes. Spatial variations in lithology and grain size of the Neogene basin-fill sediments can be established when data from numerous drill holes are considered together. Lithologic variations are related to different depositional environments within the basin including alluvial fan, channel, basin axis, and playa deposits.

  8. Geologic Characterization of Young Alluvial Basin-Fill Deposits from Drill-Hole Data in Yucca Flat, Nye County, Nevada

    Science.gov (United States)

    Sweetkind, Donald S.; Drake II, Ronald M.

    2007-01-01

    Yucca Flat is a topographic and structural basin in the northeastern part of the Nevada Test Site in Nye County, Nevada, that has been the site of numerous underground nuclear tests; many of these tests occurred within the young alluvial basin-fill deposits. The migration of radionuclides to the Paleozoic carbonate aquifer involves passage through this thick, heterogeneous section of Tertiary and Quaternary rock. An understanding of the lateral and vertical changes in the material properties of young alluvial basin-fill deposits will aid in the further development of the hydrogeologic framework and the delineation of hydrostratigraphic units and hydraulic properties required for simulating ground-water flow in the Yucca Flat area. This report by the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, presents data and interpretation regarding the three-dimensional variability of the shallow alluvial aquifers in areas of testing at Yucca Flat, data that are potentially useful in the understanding of the subsurface flow system. This report includes a summary and interpretation of alluvial basin-fill stratigraphy in the Yucca Flat area based on drill-hole data from 285 selected drill holes. Spatial variations in lithology and grain size of the Neogene basin-fill sediments can be established when data from numerous drill holes are considered together. Lithologic variations are related to different depositional environments within the basin such as alluvial fan, channel, basin axis, and playa deposits.

  9. Geologic Characterization of Young Alluvial Basin-Fill Deposits from Drill Hole Data in Yucca Flat, Nye County, Nevada

    Science.gov (United States)

    Sweetkind, Donald S.; Drake II, Ronald M.

    2007-01-01

    Yucca Flat is a topographic and structural basin in the northeastern part of the Nevada Test Site (NTS) in Nye County, Nevada, that has been the site of numerous underground nuclear tests; many of these tests occurred within the young alluvial basin-fill deposits. The migration of radionuclides to the Paleozoic carbonate aquifer involves passage through this thick, heterogeneous section of Tertiary and Quaternary rock. An understanding of the lateral and vertical changes in the material properties of young alluvial basin-fill deposits will aid in the further development of the hydrogeologic framework and the delineation of hydrostratigraphic units and hydraulic properties required for simulating ground-water flow in the Yucca Flat area. This report by the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, presents data and interpretation regarding the three-dimensional variability of the shallow alluvial aquifers in areas of testing at Yucca Flat, data that are potentially useful in the understanding of the subsurface flow system. This report includes a summary and interpretation of alluvial basin-fill stratigraphy in the Yucca Flat area based on drill hole data from 285 selected drill holes. Spatial variations in lithology and grain size of the Neogene basin-fill sediments can be established when data from numerous drill holes are considered together. Lithologic variations are related to different depositional environments within the basin including alluvial fan, channel, basin axis, and playa deposits.

  10. Comparative studies of pre- and post-drilling modelled thermal conductivity and maturity data with post-drilling results: implications for basin modelling and hydrocarbon exploration

    Energy Technology Data Exchange (ETDEWEB)

    Ho, T.T.Y.; Sahai, S.K. [Conoco Inc., Ponca City, OK (United States); Leadholm, R.H. [Conoco Inc., Houston, TX (United States); Senneseth, O. [Conoco Norway Inc., Stavanger (Norway); Jensen, R.P.

    1998-12-31

    The primary objective of this paper is to demonstrate the successful application of maturation modelling using velocity-based thermal conductivity in the whole cycle of hydrocarbon exploration (frontier, developing and mature) on the Halten Terrace, Offshore Norway. This seismic geochemical method, used as a critical technique for selecting a favourable block in the early stages of exploration in the early 80s, enabled Conoco and its partners to make the first oil discovery and the subsequent discovery of the giant Heidrun Field in the area north of the 62nd parallel. Additional data (modelling and measured) on the thermal conductivity and Ro values are now available, and provide an excellent opportunity to compare the original (pre-drilling) basin models and related modelling results of the early 80s with 1990s (post-drilling) state-of-the-art data and models. The results of the comparative study indicate that the velocity-based conductivity compares very well with measured data, particularly in an overpressured area where conventional porosity (modelled) based thermal conductivities were inadequate. The pre-drilling predicted values of heat flow, geothermal gradient and vitrinite reflectance (based on Arrhenius equation) and oil window limits also compared favourably with post-drilling measured results. Thus, the method of calculating thermal conductivity from seismic data provides a useful tool to integrate geochemistry and geophysical (seismic) data, to calibrate maturation models, and to enhance the value of geochemistry and basin modelling in hydrocarbon exploration. (Author)

  11. Integrating multi-scale geophysical and drill-core data to improve hydraulic characterization of continental sedimentary basins

    Science.gov (United States)

    Kukowski, Nina; Methe, Pascal; Goepel, Andreas

    2017-04-01

    Physical properties of rocks in the uppermost continental crust e.g. sedimentary basins are very heterogeneously distributed and anisotropic making it necessary to perform advanced post processing techniques on geophysical data. Whereas e.g. electrical resistivity or seismic tomography allow only for identifying physical properties' variability on a scale from roughly several tens of metres to several hundred metres, drill cores reveal physical heterogeneity on the cm-scale. To study the impact of small scale acoustic and hydraulic heterogeneity on fluid flow in a sedimentary basin we use combined data sets from the Thuringian Basin in Germany, a small southern extension of the North German Basin characterised by Permian to Triassic sediments. Our data sets consist of three reflection seismic lines acquired within the framework of the multidisciplinary project INFLUINS (INtegrated FLUid dynamics IN Sedimentary basins) and as site survey for deep drilling, geophysical logging data from a 1,179 m deep drill hole in the centre of the Thuringian Basin, and Multi Sensor Core Logger (MSCL) data of the cores recovered from this drill hole. Geophysical borehole logging was performed immediate after drilling on the highest vertical resolution (about 10 cm) possible using state of the art commercial logging tools. MSCL-data were acquired at an even higher resolution of about 1 to 2 cm , which enables both, calibrating logging data and zooming in the spatial heterogeneity of physical properties. These measurements are complemented with laboratory measurements of rock physical properties (e.g. thermal conductivity, permeability) using selected core samples. Here, we mainly focus on seismic (sonic velocity, density) and hydraulic (porosity, permeability) parameters. This multi-methodological approach allows us on the one hand to estimate improved local to regional average values for physical parameters but most importantly also to highlight the role of thin layers, the physical

  12. First time real-time mud gas monitoring during riser drilling in the Kumano Basin (IODP Exp 319)

    Science.gov (United States)

    Wiersberg, T.; Erzinger, J.; Horiguchi, K.; Saffer, D. M.; Byrne, T. B.; McNeill, L. C.; Araki, E.; Takahashi, K.; Eguchi, N. O.; Toczko, S.

    2009-12-01

    Chikyu Expedition 319 was the first cruise of the Integrated Ocean Drilling Program (IODP) where riser drilling was performed and real-time mud gas monitoring was conducted, because this technique requires drill-mud circulation. In contrast to conventional IODP drilling that uses drill water in combination with lost circulation, during riser drilling the drill mud returns back to the surface through a riser pipe which encases the drill pipe. The dissolved gas is extracted from returning drill mud, analyzed in real time and sampled for noble gas and stable isotopes studies. This technique has been applied in the past on scientific continental drilling projects of e.g. the International Continental Drilling Program. Expedition 319 is part of the NanTroSEIZE project, a multiexpedition, multistage IODP drilling program focused on understanding the mechanics of seismogenesis and ruptures propagation along the Nankai accretionary prism. Riser drilling was carried out on Hole C0009 that intersects the cover sediments of the Kumano Basin and probably penetrates into the accretionary prism below. Site NT2-11 is located approx. 60 km SE of the harbour of Shingu, Japan. Real-time mud gas monitoring was performed in Hole C0009 during drilling from 703 mbsf (meter below sea floor) down to 1594 mbsf and during hole enlargement from 703 mbsf to 1569 mbsf. Both datasets show similar gas distribution at depth. Gas was furthermore extracted, sampled and analyzed from drill cuttings. Drill mud gas is generally composed of air and gases that derive from the formation. The principal formation gas in drill mud from both drilling phases and in cuttings was methane. Up to 14 vol % CH4 was detected during drilling and up to 3 vol % during hole enlargement. Down to 800 mbsf and below 1280 mbsf, the methane concentration in drill mud is lower than in the surrounded interval, where methane peaks at several depths. At 1280 mbsf an unconformity is indicated from lihology, in seismic and

  13. Mesohabitat use of threatened hemlock forests by breeding birds of the Delaware River basin in northeastern United States

    Science.gov (United States)

    Ross, R.M.; Redell, L.A.; Bennett, R.M.; Young, J.A.

    2004-01-01

    Avian biodiversity may be at risk in eastern parks and forests due to continued expansion of the hemlock woolly adelgid (Adelges tsugae), an exotic homopteran insect native to East Asia. To assess avian biodiversity, mesohabitat relations, and the risk of species loss with declining hemlock forests in Appalachian park lands, 80 randomly distributed fixed-radius plots were established in which territories of breeding birds were estimated on four forest-terrain types (hemlock and hardwood benches and ravines) in the Delaware Water Gap National Recreation Area. Both species richness and number of territories were higher in hardwood than hemlock forest types and in bench than ravine terrain types. Four insectivorous species, Acadian flycatcher (Empidonax virescens), blue-headed vireo (Vireo solitarius), black-throated green warbler (Dendroica virens), and Blackburnian warbler (Dendroica fusca), showed high affinity for hemlock forest type and exhibited significantly greater numbers of territories in hemlock than hardwood sites. These species are hemlock-associated species at risk from continued hemlock decline in the Delaware River valley and similar forests of the mid-Atlantic east slope. Two of these species, the blue-headed vireo and Blackburnian warbler, appeared to specialize on ravine mesohabitats of hemlock stands, the vireo a low-to-mid canopy species, the warbler a mid-to-upper canopy forager. Unchecked expansion of the exotic adelgid and subsequent hemlock decline could negatively impact 3,600 pairs from the park and several million pairs from northeastern United States hemlock forests due to elimination of preferred habitat.

  14. Magnetostratigraphic and paleoenvironmental records for a Late Cenozoic sedimentary sequence drilled from Lop Nor in the eastern Tarim Basin

    Science.gov (United States)

    Chang, Hong; An, Zhisheng; Liu, Weiguo; Qiang, Xiaoke; Song, Yougui; Ao, Hong

    2012-01-01

    The Tarim Basin, one of the largest inland basins in the world, is situated in the northwestern China and to the north of the Tibetan Plateau. Continuous Cenozoic deposits have accumulated in this basin, which are crucial for investigating the growth of the Tibetan Plateau and the paleoclimatic evolution in Asian interior. Here we report the magnetostratigraphic and paleoenvironmental records for a Late Cenozoic sedimentary sequence drilled from Lop Nor in the eastern Tarim Basin. Magnetostratigraphic results show that this core has recorded a magnetic polarity sequence from C3Bn to C1n, covering an age range from ca. 7 Ma to the present. Decreased magnetic susceptibility occurred after ca. 5.6-5.1 Ma, which was interpreted to indicate an enhancement of aridity in the Tarim Basin since this period. We attribute this aridification to the combined effect of global climate cooling and the uplift of the Northern Tibetan Plateau since the late Miocene.

  15. Key technologies for well drilling and completion in ultra-deep sour gas reservoirs, Yuanba Gasfield, Sichuan Basin

    Directory of Open Access Journals (Sweden)

    Jiaxiang Xia

    2016-12-01

    Full Text Available The Yuanba Gasfield is a large gas field discovered by Sinopec in the Sichuan Basin in recent years, and another main exploration area for natural gas reserves and production increase after the Puguang Gasfield. The ultra-deep sour gas reservoir in the Yuanba Gasfield is characterized by complicated geologic structure, deep reservoirs and complex drilled formation, especially in the continental deep strata which are highly abrasive with low ROP (rate of penetration and long drilling period. After many years of drilling practice and technical research, the following six key drilling and completion technologies for this type reservoir are established by introducing new tools and technologies, developing specialized drill bits and optimizing drilling design. They are: casing program optimization technology for ROP increasing and safe well completion; gas drilling technology for shallow continental strata and high-efficiency drilling technology for deep high-abrasion continental strata; drilling fluid support technologies of gas–liquid conversion, ultra-deep highly-deviated wells and horizontal-well lubrication and drag reduction, hole stability control and sour gas contamination prevention; well cementing technologies for gas medium, deep-well long cementing intervals and ultra-high pressure small space; horizontal-well trajectory control technologies for measuring instrument, downhole motor optimization and bottom hole assembly design; and liner completion modes and completion string optimization technologies suitable for this gas reservoir. Field application shows that these key technologies are contributive to ROP increase and efficiency improvement of 7000 m deep horizontal wells and to significant operational cycle shortening.

  16. A reindeer footprint in a drilling core from the Allerød-Bølling age succession of Lille Slotseng basin, south-eastern Jylland, Denmark

    DEFF Research Database (Denmark)

    Noe-Nygaard, Nanna; Milàn, Jesper; Hede, Mikkel Ulfeldt

    2005-01-01

    A Subfossil reindeer track was localised in a drilled core from the Late Glacial Slotseng lacustrine basin, located in the south eastern part of Jylland near the town of Jels. It was dated to 11,795 ±80 14C yr BP or around 13,780 cal yr BP. During an earlier excavation of the site four skeletons...... shore woody peat from the Boreal and onset of the Atlantic Time, cover the basin. Hitherto, no convincing tracks have been recognized and described from drill cores. The reindeer track from the Slotseng Basin is the first convincing track recognized from a drill core section. 89...

  17. Drill hole and/or outcrop locations, Ferris Coal Zones in Hanna Basin, Wyoming, 23, 25, 31, 50 and 65 coal zones (fer*ptg)

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — These ArcView shapefiles contain representations of the public drill holes in the Ferris coal zones in the Ferris coalfield, Hanna Basin, Wyoming. These datasets...

  18. Simulation of streamflow and water quality in the Brandywine Creek subbasin of the Christina River basin, Pennsylvania and Delaware, 1994-98

    Science.gov (United States)

    Senior, Lisa A.; Koerkle, Edward H.

    2003-01-01

    The Christina River Basin drains 565 mi2 (square miles) in Pennsylvania and Delaware. Water from the basin is used for recreation, drinking-water supply, and to support aquatic life. The Christina River Basin includes the major subbasins of Brandywine Creek, Red Clay Creek, White Clay Creek, and Christina River. The Brandywine Creek is the largest of the subbasins and drains an area of 327 mi2. Water quality in some parts of the Christina River Basin is impaired and does not support designated uses of the streams. A multi-agency water-quality management strategy included a modeling component to evaluate the effects of point and nonpoint-source contributions of nutrients and suspended sediment on streamwater quality. To assist in nonpoint-source evaluation, four independent models, one for each of the four main subbasins of the Christina River Basin, were developed and calibrated using the model code Hydrological Simulation Program?Fortran (HSPF). Water-quality data for model calibration were collected in each of the four main subbasins and in small subbasins predominantly covered by one land use following a nonpoint-source monitoring plan. Under this plan, stormflow and base-flow samples were collected during 1998 at six sites in the Brandywine Creek subbasin and five sites in the other subbasins. The HSPF model for the Brandywine Creek Basin simulates streamflow, suspended sediment, and the nutrients, nitrogen and phosphorus. In addition, the model simulates water temperature, dissolved oxygen, biochemical oxygen demand, and plankton as secondary objectives needed to support the sediment and nutrient simulations. For the model, the basin was subdivided into 35 reaches draining areas that ranged from 0.6 to 18 mi2. Three of the reaches contain regulated reservoir. Eleven different pervious land uses and two impervious land uses were selected for simulation. Land-use areas were determined from 1995 land-use data. The predominant land uses in the basin are forested

  19. Structure and Dynamics of Floods in the upper Delaware River Basin: An Integrated Seasonal Forecasting System for New York City Reservoirs

    Science.gov (United States)

    Najibi, N.; Devineni, N.

    2016-12-01

    The National Weather Service River Forecasting System (NWS-RFS) issues 3-month lead probabilistic forecasts of streamflow for many river basins in the contiguous United States from 12 river forecasting centers. The Ensemble Streamflow Prediction system from NWS-RFS uses conceptual hydrologic models to issue streamflow forecasts based on the current soil moisture, river, and reservoir conditions by assuming that past meteorological events will recur in the future with historical probabilities. Recent investigations focusing on the teleconnection between anomalous sea surface temperature conditions and regional/continental hydroclimatology show that interannual and interdecadal variability in exogenous climatic indices modulates the regional streamflow patterns. In this work, we present a comprehensive framework to quantify the structure and dynamics of floods for the upper Delaware River Basin based on the interaction between the exogenous climate and weather patterns and antecedent flow regimes. We focus on estimating the conditional distribution of flood volume, duration, peak and timing based on large-scale climatic teleconnections (seasonal sea level pressure and pre-season sea surface temperature) and macroscale hydrological factors (start of the season's flow, seasonal rainfall duration and intensity, pre-season snow depth and cover in watershed, and concurrent rain over snow (ROS) events). Statistical techniques such as the semi-parametric k-nearest neighbor resampling, multivariate Kalman filters, and hierarchical Bayesian methods are explored as a strategy to address both model and parameter uncertainties. Ultimately proactive decision models embedded into the operating rules based on the forecasted future conditions -instead of reactive decisions based on current observed conditions- can result in risk mitigation.

  20. Simulation of streamflow and water quality in the White Clay Creek subbasin of the Christina River Basin, Pennsylvania and Delaware, 1994-98

    Science.gov (United States)

    Senior, Lisa A.; Koerkle, Edward H.

    2003-01-01

    The Christina River Basin drains 565 square miles (mi2) in Pennsylvania, Maryland, and Delaware. Water from the basin is used for recreation, drinking water supply, and to support aquatic life. The Christina River Basin includes the major subbasins of Brandywine Creek, White Clay Creek, and Red Clay Creek. The White Clay Creek is the second largest of the subbasins and drains an area of 108 mi2. Water quality in some parts of the Christina River Basin is impaired and does not support designated uses of the streams. A multi-agency water-quality management strategy included a modeling component to evaluate the effects of point and nonpoint-source contributions of nutrients and suspended sediment on stream water quality. To assist in non point-source evaluation, four independent models, one for each of the three major subbasins and for the Christina River, were developed and calibrated using the model code Hydrological Simulation Program?Fortran (HSPF). Water-quality data for model calibration were collected in each of the four main subbasins and in smaller subbasins predominantly covered by one land use following a nonpoint-source monitoring plan. Under this plan, stormflow and base- flow samples were collected during 1998 at two sites in the White Clay Creek subbasin and at nine sites in the other subbasins. The HSPF model for the White Clay Creek Basin simulates streamflow, suspended sediment, and the nutrients, nitrogen and phosphorus. In addition, the model simulates water temperature, dissolved oxygen, biochemical oxygen demand, and plankton as secondary objectives needed to support the sediment and nutrient simulations. For the model, the basin was subdivided into 17 reaches draining areas that ranged from 1.37 to 13 mi2. Ten different pervious land uses and two impervious land uses were selected for simulation. Land-use areas were determined from 1995 land-use data. The predominant land uses in the White Clay Creek Basin are agricultural, forested, residential

  1. Geohydrology and simulation of ground-water flow in the Red Clay Creek Basin, Chester County, Pennsylvania, and New Castle County, Delaware

    Science.gov (United States)

    Vogel, K.L.; Reif, A.G.

    1993-01-01

    The 54-square-mile Red Clay Creek Basin, located in the lower Delaware River Basin, is underlain primarily by metamorphic rocks that range from Precambrian to Lower Paleozoic in age. Ground water flows through secondary openings in fractured crystalline rock and through primary openings below the water table in the overlying saprolite. Secondary porosity and permeability vary with hydrogeologic unit, topographic setting, and depth. Thirty-nine percent of the water-bearing zones are encountered within 100 feet of the land surface, and 79 percent are within 200 feet. The fractured crystalline rock and overlying saprolite act as a single aquifer under unconfined conditions. The water table is a subdued replica of the land surface. Local ground-water flow systems predominate in the basin, and natural ground-water discharge is to streams, comprising 62 to 71 percent of streamflow. Water budgets for 1988-90 for the 45-square-mile effective drainage area above the Woodale, Del., streamflow-measurement station show that annual precipitation ranged from 43.59 to 59.14 inches and averaged 49.81 inches, annual streamflow ranged from 15.35 to 26.33 inches and averaged 20.24 inches, and annual evapotranspiration ranged from 27.87 to 30.43 inches and averaged 28.98 inches. The crystalline rocks of the Red Clay Creek Basin were simulated two-dimensionally as a single aquifer under unconfined conditions. The model was calibrated for short-term steady-state conditions on November 2, 1990. Recharge was 8.32 inches per year. Values of aquifer hydraulic conductivity in hillside topographic settings ranged from 0.07 to 2.60 feet per day. Values of streambed hydraulic conductivity ranged from 0.08 to 26.0 feet per day. Prior to simulations where ground-water development was increased, the calibrated steady-state model was modified to approximate long-term average conditions in the basin. Base flow of 11.98 inches per year and a ground-water evapotranspiration rate of 2.17 inches per

  2. Integrating petroleum and sulfur data to map the Guadalupian-Ochoan (Middle to Upper Permian) Boundary of the Delaware Basis, Trans-Pecos, Texas

    Science.gov (United States)

    Dishron, Joseph B.

    2011-12-01

    The Delaware Basin of the Permian Basin is a classic intra-cratonic basin of West Texas and Southeast New Mexico. Hydrocarbon exploration and production have occurred in the region since the early 1920s, and, as a result, the formations related to these oil and gas reserves have been studied in great detail. Some formations in the Delaware Basin, however, have not been studied in such detail, and this thesis examines one, lesser-known unit that could have economic potential. The Lamar Limestone (Lamar Lime) of the Bell Canyon Formation has commonly been dismissed as a production interval; rather, it has been described as a source and seal rock for the Ramsey Sand of the lower Bell Canyon Formation. However, recent studies found that the Lamar Lime was contributing to production, and it has been described by Trentham (2006) as a potentia "mini Barnett" reservoir. The depths of these deposits are in a range that is ideal for oil accumulation. This study made use of data from wells and test holes drilled in the western Delaware Basin, Culberson County, Texas. Many oil and gas wells have been drilled in the western Delaware Basin, but they are concentrated in the north and east portions of Culberson County. In addition, sulfur wells were drilled in the area in the late 1960s and early 1970s. Analyses of the well logs of these wells and of core and outcrop studies were completed to gain a better understanding of the distribution and economic potential of the Lamar. Both datasets were combined to provide information not readily available in the oil and gas dataset. The Lamar Lime is an excellent marker bed because it underlies thick evaporites. The evaporite sequences are Ochoan in age, and, therefore, the contact of the Lamar Lime (Bell Canyon Formation) and the Castile Formation is the approximate boundary for the Guadalupian-Ochoan Series. The Castile Formation, the Salado Formation, and the Rustler Formation (from oldest to youngest) are the evaporite units that

  3. Environmental measurement-while-drilling-gamma ray spectrometer (EMWD-GRS) system technology demonstration plan for use at the Savannah River Site F-Area Retention Basin

    Energy Technology Data Exchange (ETDEWEB)

    Williams, C.V.; Lockwood, G.J.; Normann, R.A. [Sandia National Labs., Albuquerque, NM (United States); Gruebel, R.D. [Tech Reps, Inc., Albuquerque, NM (United States)

    1996-08-01

    The Environmental Measurement-While-Drilling-Gamma Ray Spectrometer (EMWD-GRS) system represents an innovative blend of new and existing technology that provides the capability of producing real-time environmental and drillbit data during drilling operations. This demonstration plan presents information on the EMWD-GRS technology, demonstration design, Cs-137 contamination at the Savannah River Site F-Area Retention Basin, responsibilities of demonstration participants, and the policies and procedures for the demonstration to be conducted at the Savannah River Site F-Area Retention Basin. The EMWD-GRS technology demonstration will consist of continuously monitoring for gamma-radiation contamination while drilling two horizontal boreholes below the backfilled retention basin. These boreholes will pass near previously sampled vertical borehole locations where concentrations of contaminant levels are known. Contaminant levels continuously recorded by the EMWD-GRS system during drilling will be compared to contaminant levels previously determined through quantitative laboratory analysis of soil samples.

  4. Simulation of streamflow and water quality in the Red Clay Creek subbasin of the Christina River Basin, Pennsylvania and Delaware, 1994-98

    Science.gov (United States)

    Senior, Lisa A.; Koerkle, Edward H.

    2003-01-01

    (mi2) in Pennsylvania and Delaware and includes the major subbasins of Red Clay Creek, White Clay Creek, Brandywine Creek, and Christina River. The Red Clay Creek is the smallest of the subbasins and drains an area of 54 mi2. Streams in the Christina River Basin are used for recreation, drinking-water supply, and to support aquatic life. Water quality in some parts of the Christina River Basin is impaired and does not support designated uses of the stream. A multi-agency, waterquality management strategy included a modeling component to evaluate the effects of point and nonpointsource contributions of nutrients and suspended sediment on stream water quality. To assist in nonpointsource evaluation, four independent models, one for each of the four main subbasins of the Christina River Basin, were developed and calibrated using the model code Hydrological Simulation Program?Fortran (HSPF). Water-quality data for model calibration were collected in each of the four main subbasins and in smaller subbasins predominantly covered by one land use following a nonpoint-source monitoring plan. Under this plan, stormflow and base-flow samples were collected during 1998 at 1 site in the Red Clay Creek subbasin and at 10 sites elsewhere in the Christina River Basin. The HSPF model for the Red Clay Creek subbasin simulates streamflow, suspended sediment, and the nutrients, nitrogen and phosphorus. In addition, the model simulates water temperature, dissolved oxygen, biochemical oxygen demand, and plankton as secondary objectives needed to support the sediment and nutrient simulations. For the model, the basin was subdivided into nine reaches draining areas that ranged from 1.7 to 10 mi2. One of the reaches contains a regulated reservoir. Ten different pervious land uses and two impervious land uses were selected for simulation. Land-use areas were determined from 1995 land-use data. The predominant land uses in the Red Clay Creek subbasin are agricultural, forested, residential

  5. COMPETITION FOR SPACE BETWEEN FISHING AND EXPLORATORY OIL DRILLING, OBSERVED FROM A DRILLING PLATFORM IN THE ESPIRITO SANTO BASIN, SOUTHEASTERN BRAZIL

    Directory of Open Access Journals (Sweden)

    Alessandra Coutinho Thomé da Silva

    2015-03-01

    Full Text Available Fishing and oil drilling compete for space in some regions off the Brazilian coast. Fish congregate around drilling platforms, which attracts fishing vessels that may illegally breach the 500 m safety perimeter. The objective of this study was to identify the fleets that frequent the safety zone of a platform and their behavior and to determine if there was a seasonal relationship in this interaction, during two exploration campaigns, in different periods, carried out on the "Ocean Star" platform in the Espírito Santo Basin. The results indicated a high incidence of artisanal fishing vessels inside the prohibited area, and of uncooperative behavior on the part of the boat crews. The statistical method of Factorial Correspondence Analysis distinguished vessels that were using pelagic longlines to fish for dolphinfish, registered in the state of Espírito Santo and longer than 11 m, which operated during the summer campaign. Vessels fishing for scombrids, which were less than 11 m long and registered outside Espírito Santo, were prominent in the autumn-winter campaign. In conclusion, the data showed that the fleets involved in each exploratory campaign were different, but to determine the real reason why the boats insist on frequenting the area close to the platform further study is necessary.

  6. User manuals for the Delaware River Basin Water Availability Tool for Environmental Resources (DRB–WATER) and associated WATER application utilities

    Science.gov (United States)

    Williamson, Tanja N.; Lant, Jeremiah G.

    2015-11-18

    The Water Availability Tool for Environmental Resources (WATER) is a decision support system (DSS) for the nontidal part of the Delaware River Basin (DRB) that provides a consistent and objective method of simulating streamflow under historical, forecasted, and managed conditions. WATER integrates geospatial sampling of landscape characteristics, including topographic and soil properties, with a regionally calibrated hillslope-hydrology model, an impervious-surface model, and hydroclimatic models that have been parameterized using three hydrologic response units—forested, agricultural, and developed land cover. It is this integration that enables the regional hydrologic-modeling approach used in WATER without requiring site-specific optimization or those stationary conditions inferred when using a statistical model. The DSS provides a “historical” database, ideal for simulating streamflow for 2001–11, in addition to land-cover forecasts that focus on 2030 and 2060. The WATER Application Utilities are provided with the DSS and apply change factors for precipitation, temperature, and potential evapotranspiration to a 1981–2011 climatic record provided with the DSS. These change factors were derived from a suite of general circulation models (GCMs) and representative concentration pathway (RCP) emission scenarios. These change factors are based on 25-year monthly averages (normals) that are centere on 2030 and 2060. The WATER Application Utilities also can be used to apply a 2010 snapshot of water use for the DRB; a factorial approach enables scenario testing of increased or decreased water use for each simulation. Finally, the WATER Application Utilities can be used to reformat streamflow time series for input to statistical or reservoir management software. 

  7. Landscape characteristics affecting streams in urbanizing regions of the Delaware River Basin (New Jersey, New York, and Pennsylvania, U.S.)

    Science.gov (United States)

    Riva-Murray, K.; Riemann, R.; Murdoch, P.; Fischer, J.M.; Brightbill, R.

    2010-01-01

    Widespread and increasing urbanization has resulted in the need to assess, monitor, and understand its effects on stream water quality. Identifying relations between stream ecological condition and urban intensity indicators such as impervious surface provides important, but insufficient information to effectively address planning and management needs in such areas. In this study we investigate those specific landscape metrics which are functionally linked to indicators of stream ecological condition, and in particular, identify those characteristics that exacerbate or mitigate changes in ecological condition over and above impervious surface. The approach used addresses challenges associated with redundancy of landscape metrics, and links landscape pattern and composition to an indicator of stream ecological condition across a broad area of the eastern United States. Macroinvertebrate samples were collected during 2000-2001 from forty-two sites in the Delaware River Basin, and landscape data of high spatial and thematic resolution were obtained from photointerpretation of 1999 imagery. An ordination-derived 'biotic score' was positively correlated with assemblage tolerance, and with urban-related chemical characteristics such as chloride concentration and an index of potential pesticide toxicity. Impervious surface explained 56% of the variation in biotic score, but the variation explained increased to as high as 83% with the incorporation of a second land use, cover, or configuration metric at catchment or riparian scales. These include land use class-specific cover metrics such as percent of urban land with tree cover, forest fragmentation metrics such as aggregation index, riparian metrics such as percent tree cover, and metrics related to urban aggregation. Study results indicate that these metrics will be important to monitor in urbanizing areas in addition to impervious surface. ?? 2010 US Government.

  8. Radiocarbon dating of silica sinter deposits in shallow drill cores from the Upper Geyser Basin, Yellowstone National Park

    Science.gov (United States)

    Lowenstern, Jacob B.; Hurwitz, Shaul; McGeehin, John

    2016-01-01

    To explore the timing of hydrothermal activity at the Upper Geyser Basin (UGB) in Yellowstone National Park, we obtained seven new accelerator mass spectrometry (AMS) radiocarbon 14C ages of carbonaceous material trapped within siliceous sinter. Five samples came from depths of 15–152 cm within the Y-1 well, and two samples were from well Y-7 (depths of 24 cm and 122 cm). These two wells, at Black Sand and Biscuit Basins, respectively, were drilled in 1967 as part of a scientific drilling program by the U.S. Geological Survey (White et al., 1975). Even with samples as small as 15 g, we obtained sufficient carbonaceous material (a mixture of thermophilic mats, pollen, and charcoal) for the 14C analyses. Apparent time of deposition ranged from 3775 ± 25 and 2910 ± 30 14C years BP at the top of the cores to about 8000 years BP at the bottom. The dates are consistent with variable rates of sinter formation at individual sites within the UGB over the Holocene. On a basin-wide scale, though, these and other existing 14C dates hint that hydrothermal activity at the UGB may have been continuous throughout the Holocene.

  9. Evaluation of Contaminant Residues in Delaware Bay Bald Eagle Nestlings

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Bald eagle (Naliacetus leucocephalus) nesting attempts have steadily increased over the past decade in the Delaware Bay and River drainage basin; however, nesting...

  10. The Messinian Salinity Crisis: what can we expect from drilling the perched basins from the Balearic Promontory?

    Science.gov (United States)

    Johanna, Lofi; Angelo, Camerlenghi; Agnès, Maillard; Diana, Ochoa

    2015-04-01

    In spite of 40 years of multi-disciplinary research conducted on the Messinian Salinity Crisis (MSC) event, modalities, timing, causes, chronology and consequence at local and planetary scale of this event are still not yet fully understood, and the MSC event remains one of the longest-living controversies in Earth Science. A key factor for the controversy is certainly the lack of a complete record of the MSC deposits preserved in the deepest Mediterranean basins. Anywhere else, on the continental shelves and slopes, the MSC mostly generated a sedimentary/time lag corresponding to a widespread erosional surface. Correlations with the depositional units locally preserved onshore are thus complex, preventing the construction of a coherent scenario linking the outcropping MSC evaporites, the erosion on the margins, and the deposition of clastics and evaporites in the abyssal plains. Recent works based on seismic profile interpretations and conducted on the Balearic promontory allowed to evidence a series of small perched basins presently lying in different water depths stepped from the coast line down to the deep basin. These topographic lows trapped sedimentary series up to 500m thick, interpreted as MSC in age (Maillard et al., 2014; Mocnik et al., 2014; Driussi et al., in press). In the most proximal basins, these deposits have been drilled and logged for industriel purposes and consist of gypsum beds interbedded with marls. Ochoa et al. (submitted) demonstrated that these MSC deposits correlate with the Primary Lower Gypsum sequence deposited in marginal settings before the drawdown phase (Lugli et al., 2010) and that are now observed onshore in tectonically active areas. The basins located in more distal locations also contain MSC deposits (including DREAM proposal) of a Multi-phase IODP Drilling Project entitled "Uncovering A Salt Giant" (857-MDP, coord. A. Camerlenghi). The DREAM Team: A. Giovanni, H. Christian, G. deLangeGert, R. Flecker, D. Garcia

  11. Ground-water quality and its relation to hydrogeology, land use, and surface-water quality in the Red Clay Creek basin, Piedmont Physiographic Province, Pennsylvania and Delaware

    Science.gov (United States)

    Senior, Lisa A.

    1996-01-01

    The Red Clay Creek Basin in the Piedmont Physiographic Province of Pennsylvania and Delaware is a 54-square-mile area underlain by a structurally complex assemblage of fractured metamorphosed sedimentary and igneous rocks that form a water-table aquifer. Ground-water-flow systems generally are local, and ground water discharges to streams. Both ground water and surface water in the basin are used for drinking-water supply. Ground-water quality and the relation between ground-water quality and hydrogeologic and land-use factors were assessed in 1993 in bedrock aquifers of the basin. A total of 82 wells were sampled from July to November 1993 using a stratified random sampling scheme that included 8 hydrogeologic and 4 land-use categories to distribute the samples evenly over the area of the basin. The eight hydrogeologic units were determined by formation or lithology. The land-use categories were (1) forested, open, and undeveloped; (2) agricultural; (3) residential; and (4) industrial and commercial. Well-water samples were analyzed for major and minor ions, nutrients, volatile organic compounds (VOC's), pesticides, polychlorinated biphenyl compounds (PCB's), and radon-222. Concentrations of some constituents exceeded maximum contaminant levels (MCL) or secondary maximum contaminant levels (SMCL) established by the U.S. Environmental Protection Agency for drinking water. Concentrations of nitrate were greater than the MCL of 10 mg/L (milligrams per liter) as nitrogen (N) in water from 11 (13 percent) of 82 wells sampled; the maximum concentration was 38 mg/L as N. Water from only 1 of 82 wells sampled contained VOC's or pesticides that exceeded a MCL; water from that well contained 3 mg/L chlordane and 1 mg/L of PCB's. Constituents or properties of well-water samples that exceeded SMCL's included iron, manganese, dissolved solids, pH, and corrosivity. Water from 70 (85 percent) of the 82 wells sampled contained radon-222 activities greater than the proposed MCL of

  12. Ground-water quality and its relation to hydrogeology, land use, and surface-water quality in the Red Clay Creek basin, Piedmont Physiographic Province, Pennsylvania and Delaware

    Science.gov (United States)

    Senior, Lisa A.

    1996-01-01

    The Red Clay Creek Basin in the Piedmont Physiographic Province of Pennsylvania and Delaware is a 54-square-mile area underlain by a structurally complex assemblage of fractured metamorphosed sedimentary and igneous rocks that form a water-table aquifer. Ground-water-flow systems generally are local, and ground water discharges to streams. Both ground water and surface water in the basin are used for drinking-water supply. Ground-water quality and the relation between ground-water quality and hydrogeologic and land-use factors were assessed in 1993 in bedrock aquifers of the basin. A total of 82 wells were sampled from July to November 1993 using a stratified random sampling scheme that included 8 hydrogeologic and 4 land-use categories to distribute the samples evenly over the area of the basin. The eight hydrogeologic units were determined by formation or lithology. The land-use categories were (1) forested, open, and undeveloped; (2) agricultural; (3) residential; and (4) industrial and commercial. Well-water samples were analyzed for major and minor ions, nutrients, volatile organic compounds (VOC's), pesticides, polychlorinated biphenyl compounds (PCB's), and radon-222. Concentrations of some constituents exceeded maximum contaminant levels (MCL) or secondary maximum contaminant levels (SMCL) established by the U.S. Environmental Protection Agency for drinking water. Concentrations of nitrate were greater than the MCL of 10 mg/L (milligrams per liter) as nitrogen (N) in water from 11 (13 percent) of 82 wells sampled; the maximum concentration was 38 mg/L as N. Water from only 1 of 82 wells sampled contained VOC's or pesticides that exceeded a MCL; water from that well contained 3 mg/L chlordane and 1 mg/L of PCB's. Constituents or properties of well-water samples that exceeded SMCL's included iron, manganese, dissolved solids, pH, and corrosivity. Water from 70 (85 percent) of the 82 wells sampled contained radon-222 activities greater than the proposed MCL of

  13. Fischer Assays of Oil-Shale Drill Cores and Rotary Cuttings from the Greater Green River Basin, Southwestern Wyoming

    Science.gov (United States)

    ,

    2008-01-01

    Chapter 1 of this CD-ROM is a database of digitized Fischer (shale-oil) assays of cores and cuttings from boreholes drilled in the Eocene Green River oil shale deposits in southwestern Wyoming. Assays of samples from some surface sections are also included. Most of the Fischer assay analyses were made by the former U.S. Bureau of Mines (USBM) at its laboratory in Laramie, Wyoming. Other assays, made by institutional or private laboratories, were donated to the U.S. Geological Survey (USGS) and are included in this database as well as Adobe PDF-scanned images of some of the original laboratory assay reports and lithologic logs prepared by USBM geologists. The size of this database is 75.2 megabytes and includes information on 971 core holes and rotary-drilled boreholes and numerous surface sections. Most of these data were released previously by the USBM and the USGS through the National Technical Information Service but are no longer available from that agency. Fischer assays for boreholes in northeastern Utah and northwestern Colorado have been published by the USGS. Additional data include geophysical logs, groundwater data, chemical and X-ray diffraction analyses, and other data. These materials are available for inspection in the office of the USGS Central Energy Resources Team in Lakewood, Colorado. The digitized assays were checked with the original laboratory reports, but some errors likely remain. Other information, such as locations and elevations of core holes and oil and gas tests, were not thoroughly checked. However, owing to the current interest in oil-shale development, it was considered in the public interest to make this preliminary database available at this time. Chapter 2 of this CD-ROM presents oil-yield histograms of samples of cores and cuttings from exploration drill holes in the Eocene Green River Formation in the Great Divide, Green River, and Washakie Basins of southwestern Wyoming. A database was compiled that includes about 47

  14. Water quality of the Delaware and Raritan Canal, New Jersey, 1998-99

    Science.gov (United States)

    Gibs, Jacob; Gray, Bonnie; Rice, Donald E.; Tessler, Steven; Barringer, Thomas H.

    2001-01-01

    Since 1934, the Delaware and Raritan Canal has been used to transfer water from the Delaware River Basin to the Raritan River Basin. The water transported by the Delaware and Raritan Canal in New Jersey is used primarily for public supply after it has been treated at drinking-water treatment plants located in the Raritan River Basin. Recently (1999), the raw water taken from the canal during storms has required increased amounts of chemical treatments for removal of suspended solids, and the costs of removing the additional sludge or residuals generated during water treatment have increased. At present, action to control algae is unnecessary.

  15. Heterogeneous Shallow-Shelf Carbonate Buildups in the Paradox Basin, Utah and Colorado: Targets for Increased Oil Production and Reserves Using Horizontal Drilling Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Chidsey, Thomas C. Jr.; Eby, David E.; Wray, Laura L.

    2001-04-19

    The primary objective of this project was to enhance domestic petroleum production by demonstration and transfer of horizontal drilling technology in the Paradox basin, Utah, Colorado, Arizona, and New Mexico. If this project can demonstrate technical and economic feasibility, then the technique can be applied to approximately 100 additional small fields in the Paradox basin alone, and result in increased recovery of 25 to 50 million barrels (40-80 million m3) of oil. This project was designed to characterize several shallow-shelf carbonate reservoirs in the Pennsylvania (Desmoinesian) Paradox Formation, choose the best candidate(s) for a pilot demonstration project to drill horizontally from existing vertical wells, monitor well performances, and report associated validation activities.

  16. Heterogeneous Shallow-Shelf Carbonate Buildups in the Paradox Basin, Utah and Colorado: Targets for Increased Oil Production and Reserves Using Horizontal Drilling Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Chidsey, Jr., Thomas C.; Eby, David E.; Wray, Laural L.

    2001-11-26

    The project's primary objective was to enhance domestic petroleum production by demonstration and transfer of horizontal drilling technology in the Paradox Basin, Utah, Colorado, Arizona, and New Mexico. If this project can demonstrate technical and economic feasibility, then the technique can be applied to approximately 100 additional small fields in the Paradox Basin alone, and result in increased recovery of 25 to 50 million barrels (4-8 million m3) of oil. This project was designed to characterize several shallow-shelf carbonate reservoirs in the Pennsylvanian (Desmoinesian) Paradox Formation, choose the best candidate(s) for a pilot demonstration project to drill horizontally from existing vertical wells, monitor well performance(s), and report associated validation activities.

  17. Drilling, Completion, and Data Collection Plans An Assessment of Geological Carbon Sequestration Options in the Illinois Basin: Phase III

    Energy Technology Data Exchange (ETDEWEB)

    Malkewicz, Nicholas; Kirksey, Jim; Finley, Robert

    2015-05-01

    Executive Summary The Illinois Basin – Decatur Project (IBDP) is managed by the Midwest Geological Sequestration Consortium (MGSC) and is led by the Illinois State Geological Survey (ISGS) at the University of Illinois. The project site is located on the Archer Daniels Midland Company (ADM) property in Decatur, Illinois, and is a fully integrated carbon capture and storage (CCS) project that uses CO₂ captured from the ethanol-producing fermentation process at the ADM corn-processing plant (Finley et. al., 2013). IBDP has a goal of injecting one million tonnes of CO₂ into the basal sands of the Mt. Simon Sandstone over a three-year period. This is a multifaceted project, and this report details the planning and results of the drilling, completions, well testing, log data acquisition, and the Health, Safety, and Environment (HSE) aspects of the project. Three deep wells were planned for the IBDP: • The injection well: Injection Well #1 (CCS1); • The monitoring well (both in-zone and above seal): Verification Well #1 (VW1); and • The geophone monitoring well: Geophysical Monitoring Well #1 (GM1). The detailed plans for these wells are attached to the appendices of this document. The wells were drilled successfully with little deviation from the original plans. The biggest change from the plan to execution was the need to adjust for larger-than-expected loss of circulation in the Potosi section of the Knox Formation. The completions reports also attached to this document detail the well constructions as they were actually built. Injectivity testing was carried out, and the perforating plans were adjusted based on the results. Additional perforations and acidizing were performed as a result of the injectivity testing. The testing plans are detailed in this report along with the actual testing results. The injectivity testing results were used in the modeling and simulation efforts. Detailed HSE plans were developed and implemented during the planning and

  18. Assessment of blood contaminant residues in Delaware Bay bald eagle nestlings

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The bald eagle population around the lower Delaware River Basin is rebounding from near extirpation in the early 1970's to 14 active breeding pairs today....

  19. 3.0 Foundation programs for the Delaware CEMRI framework

    Science.gov (United States)

    Peter S. Murdoch

    2008-01-01

    A complete review of all the national monitoring programs that could possibly contribute to the Delaware River Basin (DRB) CEMRI Framework is beyond the scope of this report. The U.S. Environmental Protection Agency (EPA) Mid-Atlantic Integrated Assessment developed a Web-based annotated inventory of such monitoring programs for the mid-Atlantic region. Olsen et al. (...

  20. Drilling, Completion, and Data Collection Plans An Assessment of Geological Carbon Sequestration Options in the Illinois Basin: Phase III

    Energy Technology Data Exchange (ETDEWEB)

    Malkewicz, Nicholas; Kirksey, Jim; Finley, Robert

    2015-05-01

    Executive Summary The Illinois Basin – Decatur Project (IBDP) is managed by the Midwest Geological Sequestration Consortium (MGSC) and is led by the Illinois State Geological Survey (ISGS) at the University of Illinois. The project site is located on the Archer Daniels Midland Company (ADM) property in Decatur, Illinois, and is a fully integrated carbon capture and storage (CCS) project that uses CO₂ captured from the ethanol-producing fermentation process at the ADM corn-processing plant (Finley et. al., 2013). IBDP has a goal of injecting one million tonnes of CO₂ into the basal sands of the Mt. Simon Sandstone over a three-year period. This is a multifaceted project, and this report details the planning and results of the drilling, completions, well testing, log data acquisition, and the Health, Safety, and Environment (HSE) aspects of the project. Three deep wells were planned for the IBDP: • The injection well: Injection Well #1 (CCS1); • The monitoring well (both in-zone and above seal): Verification Well #1 (VW1); and • The geophone monitoring well: Geophysical Monitoring Well #1 (GM1). The detailed plans for these wells are attached to the appendices of this document. The wells were drilled successfully with little deviation from the original plans. The biggest change from the plan to execution was the need to adjust for larger-than-expected loss of circulation in the Potosi section of the Knox Formation. The completions reports also attached to this document detail the well constructions as they were actually built. Injectivity testing was carried out, and the perforating plans were adjusted based on the results. Additional perforations and acidizing were performed as a result of the injectivity testing. The testing plans are detailed in this report along with the actual testing results. The injectivity testing results were used in the modeling and simulation efforts. Detailed HSE plans were developed and implemented during the planning and

  1. Use of Cutting-Edge Horizontal and Underbalanced Drilling Technologies and Subsurface Seismic Techniques to Explore, Drill and Produce Reservoired Oil and Gas from the Fractured Monterey Below 10,000 ft in the Santa Maria Basin of California

    Energy Technology Data Exchange (ETDEWEB)

    George Witter; Robert Knoll; William Rehm; Thomas Williams

    2005-09-29

    This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conducted in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper curved sections were

  2. Use of Cutting-Edge Horizontal and Underbalanced Drilling Technologies and Subsurface Seismic Techniques to Explore, Drill and Produce Reservoired Oil and Gas from the Fractured Monterey Below 10,000 ft in the Santa Maria Basin of California

    Energy Technology Data Exchange (ETDEWEB)

    George Witter; Robert Knoll; William Rehm; Thomas Williams

    2005-09-29

    This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conducted in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper curved sections were

  3. HETEROGENEOUS SHALLOW-SHELF CARBONATE BUILDUPS IN THE PARADOX BASIN, UTAH AND COLORADO: TARGETS FOR INCREASED OIL PRODUCTION AND RESERVES USING HORIZONTAL DRILLING TECHNIQUES

    Energy Technology Data Exchange (ETDEWEB)

    David E. Eby; Thomas C. Chidsey, Jr.; Kevin McClure; Craig D. Morgan

    2003-07-01

    The Paradox Basin of Utah, Colorado, Arizona, and New Mexico contains nearly 100 small oil fields producing from carbonate buildups within the Pennsylvanian (Desmoinesian) Paradox Formation. These fields typically have one to 10 wells with primary production ranging from 700,000 to 2,000,000 barrels (111,300-318,000 m{sup 3}) of oil per field and a 15 to 20 percent recovery rate. At least 200 million barrels (31.8 million m{sup 3}) of oil will not be recovered from these small fields because of inefficient recovery practices and undrained heterogeneous reservoirs. Several fields in southeastern Utah and southwestern Colorado are being evaluated as candidates for horizontal drilling and enhanced oil recovery from existing vertical wells based upon geological characterization and reservoir modeling case studies. Geological characterization on a local scale is focused on reservoir heterogeneity, quality, and lateral continuity, as well as possible reservoir compartmentalization, within these fields. This study utilizes representative cores, geophysical logs, and thin sections to characterize and grade each field's potential for drilling horizontal laterals from existing development wells. The results of these studies can be applied to similar fields elsewhere in the Paradox Basin and the Rocky Mountain region, the Michigan and Illinois Basins, and the Midcontinent region. This report covers research activities for the second half of the third project year (October 6, 2002, through April 5, 2003). The primary work included describing and mapping regional facies of the upper Ismay and lower Desert Creek zones of the Paradox Formation in the Blanding sub-basin, Utah. Regional cross sections show the development of ''clean carbonate'' packages that contain all of the productive reservoir facies. These clean carbonates abruptly change laterally into thick anhydrite packages that filled several small intra-shelf basins in the upper Ismay zone

  4. Paleomagnetic chronology and paleoenvironmental records from drill cores from the Hetao Basin and their implications for the formation of the Hobq Desert and the Yellow River

    Science.gov (United States)

    Li, Baofeng; Sun, Donghuai; Xu, Weihong; Wang, Fei; Liang, Baiqing; Ma, Zhiwei; Wang, Xin; Li, Zaijun; Chen, Fahu

    2017-01-01

    Reconstructing the Cenozoic environmental history of Hetao Basin, in the northern part of the Ordos Plateau in North China, is important not only for revealing the evolution of the Yellow River, but also for understanding the formation of the Hobq Desert. Here we present the stratigraphic framework of drill core DR01 with length of 2503.18 m, and the results of magnetostratigraphic and ESR dating and multi-proxy analyses of drill core WEDP05 with length of 274.60 m, from the Hetao Basin. The magnetostratigraphic and ESR results indicate that core WEDP05 spans the last ∼1.68 Ma. Stratigraphic sequence of core DR01 indicates that the Hetao area was uplifted and eroded during the early Cenozoic, before subsiding to form a sedimentary basin. Subsequently, the basin was a fluvio-lacustrine environment during the Pliocene and then experienced alternating desert and fluvio-lacustrine conditions during the Quaternary. Sedimentary facies and multi environmental-proxy analyses of core WEDP05 indicate that the basin was occupied by a fluvio-lacustrine system during the following intervals: ∼1.47 - ∼1.30 Ma, ∼1.17 - ∼1.07 Ma, ∼0.68 - ∼0.60 Ma and from ∼0.47 Ma to the last interglacial; and that a desert environment developed during the lake regression phases of ∼1.30 - ∼1.17 Ma, ∼1.07 - ∼0.68 Ma and ∼0.60 - ∼0.47 Ma. The presence of aeolian sand at the base of core WEDP05 suggests that the origin of the Hobq Desert can be traced back to the early Pleistocene, and resulted from the erosion and transportation of exposed fluvio-lacustrine sediments by near-surface winds associated with the Asian winter monsoon. A large river channel in the Hetao Basin may have existed as early as the Pliocene, which was occupied by the Yellow River when its upper reaches formed by at least ∼1.6 Ma. Subsequently, at least since ∼1.2 Ma, the Yellow River formed its drainage system around the Hetao Basin and controlled the paleoenvironment evolution of the basin.

  5. Digital archive of drilling mud weight pressures and wellbore temperatures from 49 regional cross sections of 967 well logs in Louisiana and Texas, onshore Gulf of Mexico basin

    Science.gov (United States)

    Burke, Lauri A.; Kinney, Scott A.; Kola-Kehinde, Temidayo B.

    2011-01-01

    This document provides the digital archive of in-situ temperature and drilling mud weight pressure data that were compiled from several historical sources. The data coverage includes the states of Texas and Louisiana in the Gulf of Mexico basin. Data are also provided graphically, for both Texas and Louisiana, as plots of temperature as a function of depth and pressure as a function of depth. The minimum, arithmetic average, and maximum values are tabulated for each 1,000-foot depth increment for temperature as well as pressure in the Texas and Louisiana data.

  6. Palaeo-earthquake events during the late Early Palaeozoic in the central Tarim Basin (NW China: evidence from deep drilling cores

    Directory of Open Access Journals (Sweden)

    He Bizhu

    2014-07-01

    Full Text Available Various millimetre-, centimetre- and metre-scale soft-sediment deformation structures (SSDS have been identified in the Upper Ordovician and Lower-Middle Silurian from deep drilling cores in the Tarim Basin (NW China. These structures include liquefied-sand veins, liquefaction-induced breccias, boudinage-like structures, load and diapir- or flame-like structures, dish and mixed-layer structures, hydroplastic convolutions and seismic unconformities. The deformed layers are intercalated by undeformed layers of varying thicknesses that are petrologically and sedimentologically similar to the deformed layers.

  7. A key continental archive for the last 2 Ma of climatic history of the central Mediterranean region: A pilot drilling in the Fucino Basin, central Italy

    Science.gov (United States)

    Giaccio, B.; Regattieri, E.; Zanchetta, G.; Wagner, B.; Galli, P.; Mannella, G.; Niespolo, E.; Peronace, E.; Renne, P. R.; Nomade, S.; Cavinato, G. P.; Messina, P.; Sposato, A.; Boschi, C.; Florindo, F.; Marra, F.; Sadori, L.

    2015-12-01

    An 82 m long sedimentary succession was retrieved from the Fucino Basin, the largest intermountain tectonic depression of the central Apennines. The basin hosts a succession of fine-grained lacustrine sediments (ca. 900 m-thick) possibly continuously spanning the last 2 Ma. A preliminary tephrostratigraphy study allows us to ascribe the drilled 82 m long record to the last 180 ka. Multi-proxy geochemical analyses (XRF scanning, total organic/inorganic carbon, nitrogen and sulfur, oxygen isotopes) reveal noticeable variations, which are interpreted as paleohydrological and paleoenvironmental expressions related to classical glacial-interglacial cycles from the marine isotope stage (MIS) 6 to present day. In light of the preliminary results, the Fucino sedimentary succession is likely to provide a long, continuous, sensitive, and independently dated paleoclimatic archive of the central Mediterranean area.

  8. Use of Cutting-Edge Horizontal and Underbalanced Drilling Technologies and Subsurface Seismic Techniques to Explore, Drill and Produce Reservoired Oil and Gas from the Fractured Monterey Below 10,000 ft in the Santa Maria Basin of California

    Energy Technology Data Exchange (ETDEWEB)

    George Witter; Robert Knoll; William Rehm; Thomas Williams

    2006-06-30

    This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conducted in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper curved sections were

  9. USE OF CUTTING-EDGE HORIZONTAL AND UNDERBALANCED DRILLING TECHNOLOGIES AND SUBSURFACE SEISMIC TECHNIQUES TO EXPLORE, DRILL AND PRODUCE RESERVOIRED OIL AND GAS FROM THE FRACTURED MONTEREY BELOW 10,000 FT IN THE SANTA MARIA BASIN OF CALIFORNIA

    Energy Technology Data Exchange (ETDEWEB)

    George Witter; Robert Knoll; William Rehm; Thomas Williams

    2005-02-01

    This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area by Temblor Petroleum with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conducted in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper

  10. USE OF CUTTING-EDGE HORIZONTAL AND UNDERBALANCED DRILLING TECHNOLOGIES AND SUBSURFACE SEISMIC TECHNIQUES TO EXPLORE, DRILL AND PRODUCE RESERVOIRED OIL AND GAS FROM THE FRACTURED MONTEREY BELOW 10,000 FT IN THE SANTA MARIA BASIN OF CALIFORNIA

    Energy Technology Data Exchange (ETDEWEB)

    George Witter; Robert Knoll; William Rehm; Thomas Williams

    2005-02-01

    This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area by Temblor Petroleum with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conducted in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper

  11. Drill bit seismic, vertical seismic profiling, and seismic depth imaging to aid drilling decisions in the Tho Tinh structure, Nam Con Son basin, Vietnam

    Energy Technology Data Exchange (ETDEWEB)

    Borland, W.; Hayashida, N.; Kusaka, H.; Leaney, W.; Nakanishi, S.

    1996-10-01

    This paper reviews the problem of overpressure, a common reason for acquiring look-ahead VSPs, and the seismic trace inversion problem, a fundamental issue in look-ahead prediction. The essential components of intermediate VSPs were examined from acquisition through processing to inversion, and recently acquired real data were provided, which were indicative of the advances being made toward developing an exclusive high resolution VSP service. A simple interpretation method and an end product of predicted mud weight versus depth were also presented, which were obtained from the inverted acoustic impedance and empirical relations. Of paramount importance in predicting the depth to a target was the velocity function used below the intermediate TD. The use of empirical or assumed density functions was an obvious weak link in the procedure. The advent of real-time time-depth measurements from drill bit seismic allowed a continuously updated predicted target depth below the present bit depth. 8 refs., 7 figs.

  12. Simulation of streamflow and water quality in the Christina River subbasin and overview of simulations in other subbasins of the Christina River Basin, Pennsylvania, Maryland, and Delaware, 1994-98

    Science.gov (United States)

    Senior, Lisa A.; Koerkle, Edward H.

    2003-01-01

    The Christina River Basin drains 565 square miles (mi2) in Pennsylvania and Delaware and includes the major subbasins of Brandywine Creek, Red Clay Creek, White Clay Creek, and Christina River. The Christina River subbasin (exclusive of the Brandywine, Red Clay, and White Clay Creek subbasins) drains an area of 76 mi2. Streams in the Christina River Basin are used for recreation, drinking water supply, and support of aquatic life. Water quality in some parts of the Christina River Basin is impaired and does not support designated uses of the stream. A multi-agency water-quality management strategy included a modeling component to evaluate the effects of point- and nonpoint-source contributions of nutrients and suspended sediment on stream water quality. To assist in nonpoint-source evaluation, four independent models, one for each of the four main subbasins of the Christina River Basin, were developed and calibrated using the model code Hydrological Simulation Program?Fortran (HSPF). Waterquality data for model calibration were collected in each of the four main subbasins and in small subbasins predominantly covered by one land use following a nonpoint- source monitoring plan. Under this plan, stormflow and base-flow samples were collected during 1998 at two sites in the Christina River subbasin and nine sites elsewhere in the Christina River Basin. The HSPF model for the Christina River subbasin simulates streamflow, suspended sediment, and the nutrients, nitrogen and phosphorus. In addition, the model simulates water temperature, dissolved oxygen, biochemical oxygen demand, and plankton as secondary objectives needed to support the sediment and nutrient simulations. For the model, the basin was subdivided into nine reaches draining areas that ranged from 3.8 to 21.9 mi2. Ten different pervious land uses and two impervious land uses were selected for simulation. Land-use areas were determined from 1995 land-use data. The predominant land uses in the Christina

  13. HETEROGENEOUS SHALLOW-SHELF CARBONATE BUILDUPS IN THE PARADOX BASIN, UTAH AND COLORADO: TARGETS FOR INCREASED OIL PRODUCTION AND RESERVES USING HORIZONTAL DRILLING TECHNIQUES

    Energy Technology Data Exchange (ETDEWEB)

    Thomas C. Chidsey, Jr.

    2002-12-01

    The Paradox Basin of Utah, Colorado, Arizona, and New Mexico contains nearly 100 small oil fields producing from carbonate buildups within the Pennsylvanian (Desmoinesian) Paradox Formation. These fields typically have one to 10 wells with primary production ranging from 700,000 to 2,000,000 barrels (111,300-318,000 m{sup 3}) of oil per field and a 15 to 20 percent recovery rate. At least 200 million barrels (31.8 million m{sup 3}) of oil will not be recovered from these small fields because of inefficient recovery practices and undrained heterogeneous reservoirs. Several fields in southeastern Utah and southwestern Colorado are being evaluated as candidates for horizontal drilling and enhanced oil recovery from existing, vertical, field wells based upon geological characterization and reservoir modeling case studies. Geological characterization on a local scale is focused on reservoir heterogeneity, quality, and lateral continuity, as well as possible reservoir compartmentalization, within these fields. This study utilizes representative cores, geophysical logs, and thin sections to characterize and grade each field's potential for drilling horizontal laterals from existing development wells. The results of these studies can be applied to similar fields elsewhere in the Paradox Basin and the Rocky Mountain region, the Michigan and Illinois Basins, and the Midcontinent region. This report covers research activities for the first half of the third project year (April 6 through October 5, 2002). This work included capillary pressure/mercury injection analysis, scanning electron microscopy, and pore casting on selected samples from Cherokee and Bug fields, Utah. The diagenetic fabrics and porosity types found at these fields are indicators of reservoir flow capacity, storage capacity, and potential for enhanced oil recovery via horizontal drilling. The reservoir quality of Cherokee and Bug fields has been affected by multiple generations of dissolution, anhydrite

  14. Atrazine in Surface Water and Relation to Hydrologic Conditions Within the Delaware River Basin Pesticide Management Area, Northeast Kansas, July 1992 Through December 1994

    Science.gov (United States)

    Pope, Larry M.

    1995-01-01

    Since about 1960, atrazine has been used as an effective pre- and postemergent herbicide in the production of corn and grain sorghum. Atrazine is a triazine-class herbicide and was the most frequently detected herbicide in surface water of the lower Kansas River Basin of southeast Nebraska and northeast Kansas (Stamer and Zelt, 1994). Approximately 95 percent of the atrazine applied in the United States is used in corn and grain-sorghum production, predominately in the Mississippi River Basin where about 82 percent of the Nation's corn acreage is planted (CIBA-GEIGY Corp., 1992). Until recent changes in product labeling, atrazine commonly was applied at relatively high rates to control weeds around commercial and industrial areas and along railroad right-of-ways. Crop yields have increased during the last 40 years due in part to the use of herbicides in reducing weed growth and competition for moisture and nutrients. However, concern on the part of water suppliers, health officials, and the public also has increased regarding the safe and responsible use of herbicides. One issue is whether the widespread use of atrazine may pose a potential threat to public-water supplies in areas where the herbicide is used because of its ability to easily dissolve in water and its possible effects on the health of humans and aquatic life.

  15. Logging Methods Under Air Drilling Conditions in Junggar Basin%准噶尔盆地空气钻井条件下的录井方法

    Institute of Scientific and Technical Information of China (English)

    李斌; 沈文星; 周远福; 周显松

    2011-01-01

    空气钻井是以气体为介质代替钻井液携带岩屑上返到地面的钻井工艺。空气钻井的使用,给井下信息的采集、处理与资料应用带来了挑战。由于钻进工艺使用的钻头是空气锤破碎地层、岩屑磨成粉末,气体携带岩屑上返,影响了岩屑的真实性,造成岩性辨别困难,给岩性定名及地层划分、工程预报、油气水层的识别与发现都带来了难度。针对准噶尔盆地所开展过的空气钻井条件下的录井方法提出了改进措施,为今后加大在空气钻井条件下的录井工艺改进提供一定的借鉴。%Air drilling is the drilling process by taking air as medium to replace drilling mud for carrying cuttings back to the surface.Its use brings challenges to the collection,processing and application of downhole information or data.Because the bit of this process is air hammer which makes the rocks underground breaken into cuttings or powders,then the air can carry the cuttings back to the wellhead.Such a process may affect the authenticity of cuttings and cause the difficulties for lithologic discrimination or identification,including the lithologic naming,the stratigraphic classification,the engineering forecast and oil-gas-water layer discovery,etc.This paper proposes the improved measures for logging methods under the air drilling conditions performed in Junggar basin,which could be used for reference for further logging technological improvement under air drilling conditions in the future.

  16. 45130-Drilling Crew First Enter into the International Drilling Market

    Institute of Scientific and Technical Information of China (English)

    Song Zhixian; Drilling

    1995-01-01

    @@ 45130-Drilling Crew subordinate to the Fourth Drilling Company of Zhongyuan Petroleum Exploration Bureau, won the two bids of risk exploration drilling projects, respectively for China Ltd. Co. of New Zealand Petroleum Exploration Company worked in the Dongtinghu Basin in 1992 and Amoco Orient Oil Co.worked in the Fuyang area, Anhui Province in November of 1993.According to the two contracts that have been signed, the two drilling wells were successfully completed,all drilling parameters are in accordance with the requirements of both contracts.

  17. Preliminary report on fluid inclusions from halites in the Castile and lower Salado formations of the Delaware Basin, southeastern New Mexico. [Freezing-point depression

    Energy Technology Data Exchange (ETDEWEB)

    Stein, C.L.

    1985-09-01

    A suite of samples composed primarily of halite from the upper Castile and lower Salado Formations of the Permian Basin was selected from Waste Isolation Pilot Plant (WIPP) core for a reconnaissance study of fluid inclusions. Volume percent of these trapped fluids averaged 0.7% to 1%. Freezing-point depressions varied widely and appeared to be unrelated to fluid-inclusion type, to sedimentary facies, or to stratigraphic depth. However, because very low freezing points were usually associated with anhydrite, a relation may exist between freezing-point data and lithology. Dissolved sulfate values were constant through the Castile, then decreased markedly with lesser depth in the lower Salado. This trend correlates very well with observed mineralogy and is consistent with an interpretation of the occurrence of secondary polyhalite as a result of gypsum or anhydrite alteration with simultaneous consumption of dissolved sulfate from the coexisting fluids. Together with the abundance and distribution of fluid inclusions in primary or ''hopper'' crystal structures, this evidence suggests that inclusions seen in these halites did not migrate any significant geographical distance since their formation. 28 refs., 17 figs., 2 tabs.

  18. Data points (drill locations) used to assess coal resources in the San Juan Basin, CO and NM (sjbptsg)

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This is a shapefile and coverage of data points used in the assessment of coal resources of the Fruitland Formation in the San Juan Basin, Colorado and New Mexico....

  19. Heterogeneous Shallow-Shelf Carbonate Buildups in the Paradox Basin, Utah and Colorado: Targets for Increased Oil Production and Reserves Using Horizontal Drilling Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Thomas C. Chidsey; Kevin McClure; Craig D. Morgan

    2003-10-05

    The Paradox Basin of Utah, Colorado, Arizona, and New Mexico contains nearly 100 small oil fields producing from carbonate buildups within the Pennsylvanian (Desmoinesian) Paradox Formation. These fields typically have one to 10 wells with primary production ranging from 700,000 to 2,000,000 barrels (111,300-318,000 m{sup 3}) of oil per field and a 15 to 20 percent recovery rate. At least 200 million barrels (31.8 million m{sup 3}) of oil will not be recovered from these small fields because of inefficient recovery practices and undrained heterogeneous reservoirs. Several fields in southeastern Utah and southwestern Colorado are being evaluated as candidates for horizontal drilling and enhanced oil recovery from existing vertical wells based upon geological characterization and reservoir modeling case studies. Geological characterization on a local scale is focused on reservoir heterogeneity, quality, and lateral continuity, as well as possible reservoir compartmentalization, within these fields. This study utilizes representative cores, geophysical logs, and thin sections to characterize and grade each field's potential for drilling horizontal laterals from existing development wells. The results of these studies can be applied to similar fields elsewhere in the Paradox Basin and the Rocky Mountain region, the Michigan and Illinois Basins, and the Midcontinent region. This report covers research activities for the first half of the fourth project year (April 6 through October 5, 2003). The work included (1) analysis of well-test data and oil production from Cherokee and Bug fields, San Juan County, Utah, and (2) diagenetic evaluation of stable isotopes from the upper Ismay and lower Desert Creek zones of the Paradox Formation in the Blanding sub-basin, Utah. Production ''sweet spots'' and potential horizontal drilling candidates were identified for Cherokee and Bug fields. In Cherokee field, the most productive wells are located in the

  20. Delaware's first serial killer.

    Science.gov (United States)

    Inguito, G B; Sekula-Perlman, A; Lynch, M J; Callery, R T

    2000-11-01

    The violent murder of Shirley Ellis on November 29, 1987, marked the beginning of the strange and terrible tale of Steven Bryan Pennell's reign as the state of Delaware's first convicted serial killer. Three more bodies followed the first victim, and all had been brutally beaten and sadistically tortured. The body of a fifth woman has never been found. State and county police collaborated with the FBI to identify and hunt down their suspect, forming a task force of over 100 officers and spending about one million dollars. Through their knowledge and experience with other serial killers, the FBI was able to make an amazingly accurate psychological profile of Delaware's serial killer. After months of around-the-clock surveillance, Steven Pennell was arrested on November 29, 1988, one year to the day after the first victim was found. Pennell was found guilty in the deaths of the first two victims on November 29, 1989, and plead no contest to the murder of two others on October 30, 1991. Still maintaining his innocence, he asked for the death penalty so that he could spare his family further agony. Steven Pennell was executed by lethal injection on March 15, 1992.

  1. Delaware Bay, Delaware Sediment Distribution 2003 to 2004

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The area of coverage consists of 38 square miles of benthic habitat mapped from 2003 to 2004 along the middle to lower Delaware Bay Coast. The bottom sediment map...

  2. The Importance of Inputs to the Nankai Trough Subduction Zone: Integration of Results from ODP and IODP Drilling Transects in the Shikoku Basin

    Science.gov (United States)

    Underwood, M.; Saito, S.; Henry, P.; Kanamatsu, T.; Scientific Teams of IODP Expeditions 322; 333

    2011-12-01

    Three ODP and IODP drilling transects have been completed across the Nankai Trough subduction zone: Ashizuri, Muroto, and Kumano. An essential component of each transect is the so-called "reference site" seaward of the trench (ODP Sites 1173 and 1177; IODP Sites C0011 and C0012). These Shikoku Basin deposits are unusually heterogeneous, which means that virtually all types of frictional, geotechnical, and hydrogeological properties (including pore pressure) vary in 3-D both landward and seaward of the subduction front. By integrating drilling results from the three transects, we recognize the following basin-wide highlights: (1) Boundaries between lithologic units are not time-correlative. As an example, the base of the upper Shikoku Basin unit (hemipelagic/pyroclastic facies) varies in age from 7.8 Ma (C0012) to 3.3 Ma (1173). (2) A basin-wide boundary caused by diagenesis of dispersed volcanic glass shifts its stratigraphic position, with host-sediment ages that range from 5.2 Ma (C0011) to 3.3 Ma (1173). This reaction is important because it affects both porosity and interstitial water geochemistry prior to subduction. (3) Units of siliciclastic and volcaniclastic turbidites occur at middle to lower depths of the stratigraphy, but they cannot be correlated from the west to the east side of the basin. Activity within those channelized and sheet-flow turbidite systems was sensitive to changes in detrital provenance, as well as autocyclic and allocyclic forcing. (4) Clay mineral assemblages changed consistently through time. Muds deposited during the early and middle Miocene are highly enriched in smectite (>45 wt-% of bulk mud), which maximizes volumetric fluid production as strata move down the plate interface and experience smectite dehydration. (5) Because of unusually high heat flow, smectite-to-illite diagenesis begins outboard of the subduction front along the Muroto transect. That local effect of S=>I diagenesis obscures the basin-wide temporal trends in

  3. User's manual for the upper Delaware River riverine environmental flow decision support system (REFDSS), Version 1.1.2

    Science.gov (United States)

    Talbert, Colin; Maloney, Kelly O.; Holmquist-Johnson, Chris; Hanson, Leanne

    2014-01-01

    Between 2002 and 2006, the Fort Collins Science Center (FORT) at the U.S. Geological Survey (USGS) conducted field surveys, organized workshops, and performed analysis of habitat for trout and shad in the Upper Delaware River Basin. This work culminated in the development of decision support system software (the Delaware River DSS–DRDSS, Bovee and others, 2007) that works in conjunction with the Delaware River Basin Commission’s reservoir operations model, OASIS, to facilitate comparison of the habitat and water-delivery effects of alternative operating scenarios for the Basin. This original DRDSS application was developed in Microsoft Excel and is available to all interested parties through the FORT web site (http://www.fort.usgs.gov/Products/Software/DRDSS/). Initial user feedback on the original Excel-based DSS highlighted the need for a more user-friendly and powerful interface to effectively deliver the complex data and analyses encapsulated in the DSS. In order to meet this need, the USGS FORT and Northern Appalachian Research Branch (NARB) developed an entirely new graphical user interface (GUI) application. Support for this research was through the DOI WaterSmart program (http://www.doi.gov/watersmart/html/index.php) of which the USGS component is the National Water Census (http://water.usgs.gov/watercensus/WaterSMART.html). The content and methodology of the new GUI interface emulates those of the original DSS with a few exceptions listed below. Refer to Bovee and others (2007) for the original information. Significant alterations to the original DSS include: • We moved from Excel-based data storage and processing to a more powerful database back end powered by SQLite. The most notable effect of this is that the previous maximum temporal extent of 10 years has been replaced by a dynamic extent that can now cover the entire period of record for which we have data (1928–2000). • We incorporated interactive geographic information system (GIS

  4. SHRIMP zircon dating and LA-ICPMS Hf analysis of early Precambrian rocks from drill holes into the basement beneath the Central Hebei Basin, North China Craton

    Institute of Scientific and Technical Information of China (English)

    Yusheng Wan; Runlong Fan; Huiyi Sun; Xianzheng Zhao; Zejiu Wang; Dunyi Liu; Alfred Kröner; Chunyan Dong; Hangqian Xie; Yuansheng Geng; Yuhai Zhang

    2014-01-01

    The Central Hebei Basin (CHB) is one of the largest sedimentary basins in the North China Craton, extending in a northeastesouthwest direction with an area of>350 km2. We carried out SHRIMP zircon dating, Hf-in-zircon isotopic analysis and a whole-rock geochemical study on igneous and metasedi-mentary rocks recovered from drill holes that penetrated into the basement of the CHB. Two samples of gneissic granodiorite (XG1-1) and gneissic quartz diorite (J48-1) have magmatic ages of 2500 and 2496 Ma, respectively. Their zircons also record metamorphic ages of 2.41e2.51 and w2.5 Ga, respec-tively. Compared with the gneissic granodiorite, the gneissic quartz diorite has higher SREE contents and lower Eu/Eu* and (La/Yb)n values. Two metasedimentary samples (MG1, H5) mainly contain w2.5 Ga detrital zircons as well as late Paleoproterozoic metamorphic grains. The zircons of different origins haveεHf (2.5 Ga) values and Hf crustal model ages ranging from 0 to 5 and 2.7 to 2.9 Ga, respectively. Therefore, w2.5 Ga magmatic and Paleoproterozoic metasedimentary rocks and late Neoarchean to early Paleoproterozoic and late Paleoproterozoic tectono-thermal events have been identified in the basement beneath the CHB. Based on regional comparisons, we conclude that the early Precambrian basement beneath the CHB is part of the North China Craton.

  5. Post-fire seeding of great basin native plants using conventional and minimum-till rangeland drills

    Science.gov (United States)

    Objectives of post-fire seeding in the Great Basin include reestablishment of perennial cover, suppression of exotic annual weeds, and increasingly restoration of diverse plant communities. Non-conventional seeding techniques may be required when seeding mixes of grasses, forbs and shrubs containing...

  6. Delaware River and Upper Bay Sediment Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The area of coverage consists of 192 square miles of benthic habitat mapped from 2005 to 2007 in the Delaware River and Upper Delaware Bay. The bottom sediment map...

  7. Libraries in Delaware: MedlinePlus

    Science.gov (United States)

    ... this page: https://medlineplus.gov/libraries/delaware.html Libraries in Delaware To use the sharing features on ... Newark Christiana Care Health System Lewis B. Flinn Library 4755 Ogletown-Stanton Road / PO BOX 6001 Newark, ...

  8. Histograms showing variations in oil yield, water yield, and specific gravity of oil from Fischer assay analyses of oil-shale drill cores and cuttings from the Piceance Basin, northwestern Colorado

    Science.gov (United States)

    Dietrich, John D.; Brownfield, Michael E.; Johnson, Ronald C.; Mercier, Tracey J.

    2014-01-01

    Recent studies indicate that the Piceance Basin in northwestern Colorado contains over 1.5 trillion barrels of oil in place, making the basin the largest known oil-shale deposit in the world. Previously published histograms display oil-yield variations with depth and widely correlate rich and lean oil-shale beds and zones throughout the basin. Histograms in this report display oil-yield data plotted alongside either water-yield or oil specific-gravity data. Fischer assay analyses of core and cutting samples collected from exploration drill holes penetrating the Eocene Green River Formation in the Piceance Basin can aid in determining the origins of those deposits, as well as estimating the amount of organic matter, halite, nahcolite, and water-bearing minerals. This report focuses only on the oil yield plotted against water yield and oil specific gravity.

  9. SHRIMP zircon dating and LA-ICPMS Hf analysis of early Precambrian rocks from drill holes into the basement beneath the Central Hebei Basin, North China Craton

    Directory of Open Access Journals (Sweden)

    Yusheng Wan

    2014-07-01

    Full Text Available The Central Hebei Basin (CHB is one of the largest sedimentary basins in the North China Craton, extending in a northeast–southwest direction with an area of >350 km2. We carried out SHRIMP zircon dating, Hf-in-zircon isotopic analysis and a whole-rock geochemical study on igneous and metasedimentary rocks recovered from drill holes that penetrated into the basement of the CHB. Two samples of gneissic granodiorite (XG1-1 and gneissic quartz diorite (J48-1 have magmatic ages of 2500 and 2496 Ma, respectively. Their zircons also record metamorphic ages of 2.41–2.51 and ∼2.5 Ga, respectively. Compared with the gneissic granodiorite, the gneissic quartz diorite has higher ΣREE contents and lower Eu/Eu* and (La/Ybn values. Two metasedimentary samples (MG1, H5 mainly contain ∼2.5 Ga detrital zircons as well as late Paleoproterozoic metamorphic grains. The zircons of different origins have εHf (2.5 Ga values and Hf crustal model ages ranging from 0 to 5 and 2.7 to 2.9 Ga, respectively. Therefore, ∼2.5 Ga magmatic and Paleoproterozoic metasedimentary rocks and late Neoarchean to early Paleoproterozoic and late Paleoproterozoic tectono-thermal events have been identified in the basement beneath the CHB. Based on regional comparisons, we conclude that the early Precambrian basement beneath the CHB is part of the North China Craton.

  10. A Model of the Chicxulub Impact Basin Based on Evaluation of Geophysical Data, Well Logs, and Drill Core Samples

    Science.gov (United States)

    Sharpton, Virgil L.; Marin, Luis E.; Carney, John D.; Lee, Scott; Ryder, Graham; Schuraytz, Benjamin C.; Sikora, Paul; Spudis, Paul D.

    1996-01-01

    Abundant evidence now shows that the buried Chicxulub structure in northern Yucatan, Mexico, is indeed the intensely sought-after source of the ejecta found world-wide at the Cretaceous-Tertiary (K/T) boundary. In addition to large-scale concentric patterns in gravity and magnetic data over the structure, recent analyses of drill-core samples reveal a lithological assemblage similar to that observed at other terrestrial craters. This assemblage comprises suevite breccias, ejecta deposit breccias (Bunte Breccia equivalents), fine-grained impact melt rocks, and melt-matrix breccias. All these impact-produced lithologies contain diagnostic evidence of shock metamorphism, including planar deformation features in quartz, feldspar, and zircons; diaplectic glasses of quartz and feldspar; and fused mineral melts and whole-rock melts. In addition, elevated concentrations of Ir, Re, and Os, in meteoritic relative proportions, have been detected in some melt-rock samples from the center of the structure. Isotopic analyses, magnetization of melt-rock samples, and local stratigraphic constraints identify this crater as the source of K/T boundary deposits.

  11. Application of geochemical logging for palaeoenvironmental research in the Late Cretaceous Qingshankou Formation from the Chinese Continental Scientific Drilling Project-SK-2e, Songliao Basin, NE China

    Science.gov (United States)

    Peng, Cheng; Zou, Changchun; Pan, Li; Niu, Yixiong

    2017-08-01

    The Chinese Continental Scientific Drilling Project of the Cretaceous Songliao Basin (CCSD-SK) provides an excellent opportunity to understand the response of terrestrial environments to greenhouse climate change in the Cretaceous. We conducted a palaeoenvironmental study of the Late Cretaceous Qingshankou Formation (K2qn) based on geochemical log data from the SK-2 east borehole. According to the characteristic of Ti mainly from terrigenous minerals, the content of authigenic elements was calculated. Correlation space was proposed to study the variation of the correlation between two log curves along the depth. Palaeoenvironmental proxies were selected from log data to study the evolution of the climate and lake, productivity of the paleolake, and organic matter deposition. The results demonstrate that the productivity of the paleolake was driven by chemical weathering in K2qn, in which the first section of the Qingshankou Formation (K2qn1) has higher productivity than the second and third sections of the Qingshankou Formation (K2qn2+3). The high content of pyrite in several thin layers reveals lake water of high sulfate concentration. This may have been caused by acid rain related to large volcanic activity. In K2qn2+3, several periods of high productivity without the formation of source rocks and high organic matter content were identified. This may show that organic matter deposition was limited by low accommodation space or oxidation environment. Therefore, the preservation condition is suggested as the main controlling factor of organic matter deposition in K2qn.

  12. Diamond drilling for geologic information in the middle Precambrian basins in the western portion of northern Michigan. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Trow, J.

    1979-10-01

    Between September 26, 1977, and May 11, 1978, six initially vertical holes probed a total of 9896 feet (1109 feet or 11.2% in overburden, 155 feet or 1.6% in Precambrian Y mafic dikes, 8386 feet or 84.7% in Precambrian X Goodrich Quartzite and Michigamme Formation, and 246 feet or 2.5% in Precambrian W basement lithologies). In addition to normal examination of core, logging, and storing of core, the holes were extensively logged geophysically, acidized core was tested for phosphate content by ammonium molybdate, splits from five out of every thirty feet of core were subjected to chemical scrutiny, thin sections of all lithologies were examined, and radiometric determinations of geologic age were made for confirmation of Precambrian W basement which was encountered in each of the three basins in Marquette County.

  13. Report of the River Master of the Delaware River for the period December 1, 2008–November 30, 2009

    Science.gov (United States)

    Krejmas, Bruce E.; Paulachok, Gary N.; Mason, Jr., Robert R.; Owens, Marie

    2016-04-06

    A Decree of the Supreme Court of the United States, entered June 7, 1954, established the position of Delaware River Master within the U.S. Geological Survey (USGS). In addition, the Decree authorizes diversions of water from the Delaware River Basin and requires compensating releases from certain reservoirs, owned by New York City, to be made under the supervision and direction of the River Master. The Decree stipulates that the River Master will furnish reports to the Court, not less frequently than annually. This report is the 56th Annual Report of the River Master of the Delaware River. It covers the 2009 River Master report year, the period from December 1, 2008, to November 30, 2009.During the report year, precipitation in the upper Delaware River Basin was 50.89 inches (in.) or 116 percent of the long-term average. Combined storage in Pepacton, Cannonsville, and Neversink Reservoirs remained high throughout the year and did not decline below 80 percent of combined capacity at any time. Delaware River operations during the year were conducted as stipulated by the Decree and the Flexible Flow Management Program (FFMP).Diversions from the Delaware River Basin by New York City and New Jersey were in full compliance with the Decree. Reservoir releases were made as directed by the River Master at rates designed to meet the flow objective for the Delaware River at Montague, New Jersey, on 25 days during the report year. Releases were made at conservation rates—rates designed to relieve thermal stress and protect the fishery and aquatic habitat in the tailwaters of the reservoirs—on all other days.During the report year, New York City and New Jersey complied fully with the terms of the Decree, and directives and requests of the River Master.As part of a long-term program, the quality of water in the Delaware Estuary between Trenton, New Jersey, and Reedy Island Jetty, Delaware, was monitored at various locations. Data on water temperature, specific conductance

  14. The effect of an oil drilling operation on the trace metal concentrations in offshore bottom sediments of the Campos Basin oil field, SE Brazil.

    Science.gov (United States)

    Rezende, C E; Lacerda, L D; Ovalle, A R C; Souza, C M M; Gobo, A A R; Santos, D O

    2002-07-01

    The concentrations of Al, Fe, Mn, Zn, Cu, Pb, Ni, Cr, Ba, V, Sn and As in offshore bottom sediments from the Bacia de Campos oil field, SE Brazil, were measured at the beginning and at 7 months after completion of the drilling operation. Concentrations of Al, Fe, Ba, Cr, Ni and Zn were significantly higher closer to the drilling site compared to stations far from the site. Average concentrations of Al, Cu, and in particular of Ni, were significantly higher at the end of the drilling operation than at the beginning. Comparison between drilling area sediments with control sediments of the continental platform, however, showed no significant difference in trace metal concentrations. Under the operation conditions of this drilling event, the results show that while changes in some trace metal concentrations do occur during drilling operations, they are not significantly large to be distinguished from natural variability of the local background concentrations.

  15. Delaware Bay Upper Shelf Bottom Sediments 2008-2010

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Coastal Program of Delaware's Division of Soil and Water conservation (DNREC), the University of Delaware, Partnership for the Delaware Estuary, and the New...

  16. Riserless drilling (managed pressure drilling)

    OpenAIRE

    Khan, Ahsan

    2012-01-01

    There are several problems which an oil and gas industry is facing. These problems can be solved by riserless drilling method which comes under managed pressure drilling umbrella. The most important problem is increasing number of casing strings to complete a well and to control a well in limited pressure profile. A well model was developed and both conventional and riserless drilling approaches were applied to see how many casings will be needed to complete a same well with these approach...

  17. University of Delaware Energy Institute

    Energy Technology Data Exchange (ETDEWEB)

    Klein, Michael T

    2012-09-30

    The main goal of this project funded through this DOE grant is to help in the establishment of the University of Delaware Energy Institute (UDEI) which is designed to be a long-term, on-going project. The broad mission of UDEI is to develop collaborative programs encouraging research activities in the new and emerging energy technologies and to partner with industry and government in meeting the challenges posed by the nation's pressing energy needs.

  18. Drilling reorganizes

    Science.gov (United States)

    Richman, Barbara T.

    As the first in a proposed series of steps that would move scientific ocean drilling from its own niche within the National Science Foundation's (NSF) Directorate for Astronomical, Atmospheric, Earth, and Ocean Sciences (AAEO) into the agency's Division of Ocean Sciences, Grant Gross, division director, has been appointed acting director of the Office of Scientific Ocean Drilling (OSOD). Gross will retain the directorship of the division, which also is part of AAEO. Allen M. Shinn, Jr., OSOD director for nearly 2 years, has been reassigned effective July 10 to a position in NSF's Office of Planning and Resource Management.The move aims to tie drilling operations more closely to the science with which it is associated, Gross said. This first step is an organizational response to the current leaning toward using a commercial drilling vessel as the drilling platform, he said. Before the market for such commercial drill ships opened (Eos, February 22, 1983, p . 73), other ship options for scientific ocean drilling included refurbishing the aging Glomar Challenger or renovating, at great expense, the Glomar Explorer. A possible next step in the reorganization is to make OSOD the third section within the Ocean Sciences Division. Currently, the division is divided into the Oceanographic Facilities and Support Section and the Ocean Sciences Research Section.

  19. The research and application of the fast drilling fluid technology in Hailaer Basin%快速钻井液技术在海拉尔盆地的应用研究

    Institute of Scientific and Technical Information of China (English)

    杨宇平; 金波; 蒋欢; 于兴东; 张坤; 谈心; 孙金声; 江四清

    2011-01-01

    In Hailaer area there exists serious mud-making in the borehole upper formation and mud ring is easily formed to give rise to serious sticking. The poor drillability and strong abrasiveness in the middle and lower formations lead to the low penetration rate as well as long drilling cycles. It is easy for the well wall to collapse and blocks to fall seriously in the lower formation. All these seriously affect the progress of exploration and development in Hailaer. Therefore, the fast drilling fluid . Technology was adopted to conduct the field test to improve the penetration rate in Well 126-88 of Hailaer Basin. The result showed that the fast drilling agent had a desirable compatibility with the amphoteric compound ion drilling fluid system applied on the spot. The agent had no effect on the normal performance and rheological property of the drilling fluid, thus effectively solving the problems of the instability of the well wall and the sticking in the process of tripping. The borehole of the test section was regular, the average penetration rate was improved by over 23.31% and the drilling cycle was shortened effectively.%海拉尔区域井中上部地层造浆严重,易形成泥环,导致严重阻卡,中下部地层可钻性差,研磨性强,导致钻井机械钻速低、钻井周期长,下部地层易发生井壁垮塌、严重掉块等现象,严重影响海拉尔区域勘探开发进程.为此,采用快速钻井液技术在海拉尔盆地乌126-88井进行了现场提高机械钻速试验.结果表明,快速钻井剂与现场所用的两性复合离子钻井液体系具有良好的配伍性,对钻井液常规性能及流变性没有影响,且有效解决了井壁失稳以及起下钻过程中的阻卡问题,试验井段井径规则,平均机械钻速提高23.31%以上,有效缩短了钻井周期.

  20. 33 CFR 165.511 - Security Zone; Atlantic Ocean, Chesapeake & Delaware Canal, Delaware Bay, Delaware River and its...

    Science.gov (United States)

    2010-07-01

    ... escorted passenger vessels in the Captain of the Port, Delaware Bay zone as defined in 33 CFR 3.25-05. (b... vessel in order to ensure safe passage in accordance with the Navigation Rules as seen in 33 CFR...

  1. 2005 Delaware Coastal Program Lidar: Sussex County

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The data were acquired in March 2005 using the NASA Experimental Advanced Airborne Research Lidar (EAARL) platform in Sussex County, Delaware. Once acquired, the...

  2. Western Canada SAGD drilling and completions performance

    Energy Technology Data Exchange (ETDEWEB)

    Turchin, S.; Tucker, R. [Ziff Energy Group (Canada)

    2011-07-01

    In the heavy oil industry, steam assisted gravity drainage (SAGD) is a thermal recovery method used to enhance oil recovery. In 2009, Ziff Energy carried out a study on SAGD drilling and completions performance in Western Canada. This paper presents the methodology used to assess drilling performances and the results obtained. This study was conducted on 159 SAGD well pairs and 1,833 delineation wells in the Western Canadian Sedimentary Basin from late 2004 to fall 2008. The drilling performance assessment was calculated from several aspects including well quality, drilling and completions cost performance and drilling time analysis. This study provided a detailed analysis of drilling and completions costs of SAGD which can help companies to improve their performance.

  3. Laser Drilling Practical Applications

    CERN Document Server

    Yilbas, Bekir Sami

    2013-01-01

    This book introduces laser drilling processes including modelling, quality assessment of drilled holes, and laser drilling applications. It provides insights into the laser drilling process and the relation among the drilling parameters pertinent to improved end product quality. This book is written for engineers and scientists working on laser machining, particularly laser drilling.

  4. Research on the Effects of the Contents of Radioactive Elements on Granularity and Climate Change: An Example of SZK1 and SZK2 Drill Holes Strata in the Fuzhou Basin

    Institute of Scientific and Technical Information of China (English)

    Zheng Rongzhang; Xu Xiwei; Li Jianping

    2006-01-01

    Based on the content of radioactive elements (U, Th, K) of strata in two drill holes in the Fuzhou basin, and combined with the result of spore-pollen analysis, the relationship between radioactivity and lithology and deposit environments is discussed and the results show that the content of radioactive substances is related to the granularity and lithology in sediment, and it is higher in argillaceous sediment (e.g. silt and clay), lower in sand sediment and in the middle in gravels between the above two kinds of sediment. The content of radioactive substances is also related to paleoclimate. A warm and humid environment is propitious to the deposition of radioactive substances, while a cool and dry climate is just the reverse.

  5. 78 FR 14060 - Television Broadcasting Services; Seaford, Delaware and Dover, Delaware

    Science.gov (United States)

    2013-03-04

    ... COMMISSION 47 CFR Part 73 Television Broadcasting Services; Seaford, Delaware and Dover, Delaware AGENCY... and seeks a waiver of the Commission's freeze on the filing of petitions for rulemaking by televisions... with its first local television service, and that Seaford will remain well-served after the...

  6. Heterogeneous Shallow-Shelf Carbonate Buildups in the Paradox Basin, Utah and Colorado: Targets for Increased Oil Production and Reserves Using Horizontal Drilling Techniques

    Energy Technology Data Exchange (ETDEWEB)

    Wray, Laura L.; Eby, David E.; Chidsey, Jr., Thomas C.

    2002-07-24

    This report covers research activities for the second half of the second project year (October 6, 2001, through April 5, 2002). This work includes description and analysis of cores, correlation of geophysical well logs, reservoir mapping, petrographic description of thin sections, cross plotting of permeability and porosity data, and development of horizontal drilling strategies for the Little Ute and Sleeping Ute fields in Montezuma County, Colorado. Geological characterization on a local scale focused on reservoir heterogeneity, quality, and lateral continuity, as well as possible compartmentalization, within these fields. This study utilizes representative core, geophysical logs, and thin sections to characterize and grade each field's potential for drilling horizontal laterals from existing development wells.

  7. Bucket drill

    Energy Technology Data Exchange (ETDEWEB)

    Bezverkhiy, V.M.; Nabokov, I.M.; Podoksik, D.Z.; Sadovskiy, S.S.; Shanyukevich, V.A.

    1983-01-01

    The bucket drill including a cylindrical housing with bottom, ground intake windows and cutting knives is hinged to the housing, the mechanism of rotation of the cutting knives including rods connected by the cutter knives, and drive shaft is distinguished by the fact that in order to improve the effectiveness of drilling by automatic change in the angle of cutting depending on the strength of the drillable rock, the drill is equipped with elastic elements and cap with annular slits in which there are elastic elements. The mechanism of rotation of the cutting knives is equipped with levers hinged to the housing, pins with shaft and rocker arm. The rods are made with a slit and from one end are rigidly connected to the cutting knives, and from the other end to the levers by means of pins which are arranged in slits of the rod with the possibility of movement. The upper ends of the levers are installed with the possibility of movement in the pins whose shafts are arranged with the possibility of rotation in the rocker arm rigidly connected to the drive shaft. The drive shaft is equipped with cantilevers installed in the cap with the possibility of rotation and interaction with the elastic elements.

  8. 33 CFR 117.235 - Chesapeake and Delaware Canal.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Chesapeake and Delaware Canal. 117.235 Section 117.235 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Delaware § 117.235 Chesapeake and Delaware Canal. The draw of the Conrail bridge, mile...

  9. IODP workshop: developing scientific drilling proposals for the Argentina Passive Volcanic Continental Margin (APVCM) - basin evolution, deep biosphere, hydrates, sediment dynamics and ocean evolution

    Science.gov (United States)

    Flood, Roger D.; Violante, Roberto A.; Gorgas, Thomas; Schwarz, Ernesto; Grützner, Jens; Uenzelmann-Neben, Gabriele; Hernández-Molina, F. Javier; Biddle, Jennifer; St-Onge, Guillaume; Workshop Participants, Apvcm

    2017-05-01

    The Argentine margin contains important sedimentological, paleontological and chemical records of regional and local tectonic evolution, sea level, climate evolution and ocean circulation since the opening of the South Atlantic in the Late Jurassic-Early Cretaceous as well as the present-day results of post-depositional chemical and biological alteration. Despite its important location, which underlies the exchange of southern- and northern-sourced water masses, the Argentine margin has not been investigated in detail using scientific drilling techniques, perhaps because the margin has the reputation of being erosional. However, a number of papers published since 2009 have reported new high-resolution and/or multichannel seismic surveys, often combined with multi-beam bathymetric data, which show the common occurrence of layered sediments and prominent sediment drifts on the Argentine and adjacent Uruguayan margins. There has also been significant progress in studying the climatic records in surficial and near-surface sediments recovered in sediment cores from the Argentine margin. Encouraged by these recent results, our 3.5-day IODP (International Ocean Discovery Program) workshop in Buenos Aires (8-11 September 2015) focused on opportunities for scientific drilling on the Atlantic margin of Argentina, which lies beneath a key portion of the global ocean conveyor belt of thermohaline circulation. Significant opportunities exist to study the tectonic evolution, paleoceanography and stratigraphy, sedimentology, and biosphere and geochemistry of this margin.

  10. Drilling equipment

    Energy Technology Data Exchange (ETDEWEB)

    Voyevodin, Yu.M.; Kholosha, Ye.G.; Leshchenko, A.G.; Timchenko, A.I.

    1979-01-10

    The invention refers to units designed for extracting minerals by mechanical action on the face by a cutting tool. There is a known drills which includes a pulse device which contains a combustion chamber, cylinder, piston-percussion tool and cutting tool. The combustion chamber and the sub-piston cavity of the cylinder are connected by a channel in which there is a distributor. Its shortcoming is the fact that the pulse device does not guarantee the necessary motion of the actuating mechanism for its velocity and frequency of the shocks on the cutting tool. This reduces the efficiency of the operation and limits the area of application. The purpose of the proposed invention is to improve productivity of the device. This is achieved because the head of the drill is equipped with a 2-piston pulse device which contains 2-combustion chambers, 2 working cylinders, 2 piston percussion instruments, a rod with gas-conducting and connecting channels for interconnection of the sub-piston cavities and combustion chambers of both cylinders. The spent gases of one cylinder are used for closing the combustion chamber of the second cylinder.

  11. Offshore waste management monitoring system: drilling campaign BM-CAL-4 Block, Camanu-Almada Basin, Bahia, Brazil; Gestao de rejeitos offshore em areas sensiveis e ambientes isolados - estudo de caso: campanha exploratoria da El Paso no Bloco BM-CA-4, Bacia de Camamu-Almada, Bahia, Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Ranieri, Adriano [El Paso Oleo e Gas, Natal, RN (Brazil); Perez, Pedro; Andrade, Albert [EnvironPact, Rio de Janeiro, RJ (Brazil)

    2008-07-01

    The present paper addresses the principal aspects related to the difficulties found to implement a pollution control project in sensitive areas and isolated environments. For that, it was utilized a case study on the El Paso's second exploratory campaign on BM-CAL-4 Block, located in Camamu Almada Basin, Bahia - Brazil. Two of the items of the pollution control project implemented on this campaign where herein detailed: drilling wastes management and waste management on the smaller vessels, which had to attend to the same requirements applied to the supply vessels and the drilling rig, due to the discharge restrictions established by the environmental agency. (author)

  12. Delaware Bay Database; Delaware Sea Grant College Program, 28 June 1988 (NODC Accession 8900151)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Delaware Bay database contains records of discrete quality observations, collected on 40 oceanographic cruises between May 1978 and October 1985. Each record...

  13. U. of Delaware Abandons Sessions on Diversity

    Science.gov (United States)

    Hoover, Eric

    2007-01-01

    The University of Delaware spent years refining its residence-life education program. One week of public criticism unraveled it. Late last month, the Foundation for Individual Rights in Education, a free-speech group, accused the university of promoting specific views on race, sexuality, and morality in a series of discussions held in dormitories.…

  14. Kids Count in Delaware: Fact Book, 1995.

    Science.gov (United States)

    Delaware Univ., Newark. Kids Count in Delaware.

    This Kids Count fact book examines statewide trends in the well-being of Delaware's children. The statistical portrait is based on key indicators in four areas: single-parent families, births to teenage mothers, juvenile crime and violence, and education. Following brief sections on the state's demographics and economic status, the fact book…

  15. Results of the 1975 Delaware PLATO Project.

    Science.gov (United States)

    Hofstetter, Fred T.

    During the Spring semester of 1975, the University of Delaware initiated a PLATO project with the dual purpose of demonstrating how a computer system might function in a university and of evaluating what part such a system might play in the future of the university and its supporting community. The demonstration phase of the project, which…

  16. Optimizing drilling performance using a selected drilling fluid

    Science.gov (United States)

    Judzis, Arnis [Salt Lake City, UT; Black, Alan D [Coral Springs, FL; Green, Sidney J [Salt Lake City, UT; Robertson, Homer A [West Jordan, UT; Bland, Ronald G [Houston, TX; Curry, David Alexander [The Woodlands, TX; Ledgerwood, III, Leroy W.

    2011-04-19

    To improve drilling performance, a drilling fluid is selected based on one or more criteria and to have at least one target characteristic. Drilling equipment is used to drill a wellbore, and the selected drilling fluid is provided into the wellbore during drilling with the drilling equipment. The at least one target characteristic of the drilling fluid includes an ability of the drilling fluid to penetrate into formation cuttings during drilling to weaken the formation cuttings.

  17. New types of drilling tools fit with PCD elements

    Directory of Open Access Journals (Sweden)

    Koníèek Jiøí

    1997-09-01

    Full Text Available One of the most significant developments in drilling technology over the last years has been the introduction of polycrystalline diamond (PCD as macro-cutting elements in the rotary drill application. This paper gives a summary of core bits and cutter bits, produced by Pramet Šumperk Co., which are fit with these PCD elements. Some results, obtained with these types of cutter bits by drilling in mines of Ostrava-Karviná Basin, are also presented.

  18. Follow the drill

    Energy Technology Data Exchange (ETDEWEB)

    Fitch-Roy, O. [Dando Drilling International (United Kingdom)

    2005-08-01

    The paper discusses modern drilling techniques with which Dando Drilling has been involved. It describes equipment supplied to opencast coal operations in Kalimantan, Borneo. These include polycrystalline diamond drill bits, flushing media, rig drilling controls and other specialised equipment. 3 photos.

  19. Real-time environmental monitoring system: drilling campaign BM-CAL-4 Block, Camanu-Almada Basin, Bahia, Brazil; Sistema de monitoramento ambiental em tempo-real: Bloco BM-CAL-4, Bacia de Camamu-Almada, Bahia, Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Pedro [El Paso Oleo e Gas, Natal, RN (Brazil); Cabral, Alexandre P. [Fugro OceansatPeg (Brazil)

    2008-07-01

    Between February and November 2007, the El Paso Oleo e Gas do Brasil Ltda. carried out a second exploratory campaign at the BM-CAL-4 Block (Camamu-Almada Basin), installing a real-time transmission metocean data monitoring system. Two metocean Wavescan (WS) buoys from Fugro were installed, transmitting current, wave and wind data to the El Paso crises room. The WS1 was positioned near the oil (10,5 km from the shore, at 22m depth), and the WS2 was located near the entrance of Barra Grande area (4,w km from the coast, at 10m depth). The real rime data fed the mathematical simulation using an oil spill model from Fugro Oceansatpeg. The metocean data Real-Time Environmental Monitoring System proved to be an important tool in the environmental management of the drilling activity located near the coastline. The sampling and real-time transmission of the current, wind and wave data allowed a better decision making regarding the selection of the best response strategies, saving time and resources in the simulation exercises, a vital issue in case of a real oil spill accident. (author)

  20. Paleoclimatic implications of magnetic susceptibility in Late Pliocene-Quaternary sediments from deep drilling core SG-1 in the western Qaidam Basin (NE Tibetan Plateau)

    Science.gov (United States)

    Zhang, Weilin; Appel, Erwin; Fang, Xiaomin; Yan, Maodu; Song, Chunhui; Cao, Liwan

    2012-06-01

    Lake sediments are important archives of paleoclimate change and erosion history. A 938.5 m long core (SG-1) of lacustrine sediments, dated at 2.77 Ma to 0.1 Ma, was obtained from the western Qaidam Basin in the northeastern Tibetan Plateau, consisting of dark grayish mudstone and grayish siltstone, intercalated with salts and fine sandstones in the upper part. Magnetic susceptibility data, combined with detailed rock magnetic properties, were analyzed for revealing the significance of ferro(i)magnetic concentration for past changes of climate and erosion. Mass-specific susceptibility (χ) shows a striking cyclic and long-term variation. Samples with high χ values are dominated by magnetite and maghemite with pseudo-single-domain properties. In contrast, samples with low χ values contain maghemite from single-domain to multidomain and, additionally, a significant fraction of hematite. The driving mechanism of χ variation can be explained by three alternative models: (1) different source regions with alternations of wind and cryoclastic erosion in a wider hinterland (dry-cold climate) and surface runoff erosion from a narrower area (more humid climate) and (2 and 3) low-temperature oxidation, occurring either in the lake sediments (dry climate) or in the catchment area during weathering (more humid climate). Trends of χ match with changes in sedimention rates and are roughly synchronous with the deep-sea δ18O record on a glacial-interglacial timescale. Therefore, the concentration of magnetic minerals in the western Qaidam Basin sediments is likely controlled by both tectonic influence and paleoenvironmental changes but can be best interpreted by alternations and trends of dry-cold and more humid periods due to Asian drying and global cooling.

  1. CASING DRILLING TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Nediljka Gaurina-Međimurec

    2005-12-01

    Full Text Available Casing drilling is an alternative option to conventional drilling and uses standard oilfield casing instead of drillstring. This technology is one of the greatest developments in drilling operations. Casing drilling involves drilling and casing a well simultaneously. In casing driling process, downhole tools can be retrieved, through the casing on wire-line, meaning tool recovery or replacement of tools can take minutes versus hours under conventional methods. This process employs wireline-retrievable tools and a drill-lock assembly, permitting bit and BHA changes, coring, electrical logging and even directional or horizontal drilling. Once the casing point is reached, the casing is cemented in place without tripping pipe.

  2. CASING DRILLING TECHNOLOGY

    OpenAIRE

    Nediljka Gaurina-Međimurec

    2005-01-01

    Casing drilling is an alternative option to conventional drilling and uses standard oilfield casing instead of drillstring. This technology is one of the greatest developments in drilling operations. Casing drilling involves drilling and casing a well simultaneously. In casing driling process, downhole tools can be retrieved, through the casing on wire-line, meaning tool recovery or replacement of tools can take minutes versus hours under conventional methods. This process employs wireline-re...

  3. Enzyme activities in the Delaware Estuary affected by elevated suspended sediment load

    Science.gov (United States)

    Ziervogel, K.; Arnosti, C.

    2009-09-01

    Extracellular enzyme activities were compared among surface water, bottom water, and sediments of the Delaware Estuary using six fluorescently labeled, structurally distinct polysaccharides to determine the effects of suspended sediment transport on water column hydrolytic activities. Potential hydrolysis rates in surface waters were also measured for the nearby shelf. Samples were taken in December 2006, 6 months after a major flood event in the Delaware Basin that was followed by high freshwater run-off throughout the fall of 2006. All substrates were hydrolyzed in sediments and in the water column, including two (pullulan and fucoidan) that previously were not hydrolyzed in surface waters of the Delaware estuary. At the time of sampling, total particulate matter (TPM) in surface waters at the lower bay, bay mouth, and shelf ranged between 31 mg l -1 and 48 mg l -1 and were 2 to 20 times higher than previously reported. The presence of easily resuspended sediments at the lower bay and bay mouth indicated enhanced suspended sediment transport in the estuary prior to our sampling. Bottom water hydrolysis rates at the two sites affected by sediment resuspension were generally higher than those in surface waters from the same site. Most notably, fucoidan and pullulan hydrolysis rates in bay mouth bottom waters were 22.6 and 6.2 nM monomer h -1, respectively, and thus three and five times higher than surface water rates. Our data suggest that enhanced mixing processes between the sediment and the overlying water broadened the spectrum of water column hydrolases activity, improving the efficiency of enzymatic degradation of high molecular weight organic matter in the water with consequences for organic matter cycling in the Delaware estuary.

  4. Robotic Planetary Drill Tests

    Science.gov (United States)

    Glass, Brian J.; Thompson, S.; Paulsen, G.

    2010-01-01

    Several proposed or planned planetary science missions to Mars and other Solar System bodies over the next decade require subsurface access by drilling. This paper discusses the problems of remote robotic drilling, an automation and control architecture based loosely on observed human behaviors in drilling on Earth, and an overview of robotic drilling field test results using this architecture since 2005. Both rotary-drag and rotary-percussive drills are targeted. A hybrid diagnostic approach incorporates heuristics, model-based reasoning and vibration monitoring with neural nets. Ongoing work leads to flight-ready drilling software.

  5. Introduction to drilling technology

    Science.gov (United States)

    Mellor, Malcom

    1989-12-01

    Terrestrial drilling technology is reviewed. The general requirements for a drilling system are given and conventional drilling techniques (rotary drag-bit, rotary roller-bit, percussive, rotary percussive) are described. Unconventional techniques for penetrating solids are outlined, including thermal drilling (spalling or melting), projectile penetration, high pressure liquid jets, explosive jets, erosion by projectile streams, and chemical penetration. Special attention is given to drilling in ice and frozen soils, performance data are given, including values for penetration rate and specific energy consumption. The principles, theory and equipment relating to each drilling technique are indicated by means of diagrams.

  6. Daily Flow Model of the Delaware River Basin. Main Report.

    Science.gov (United States)

    1981-09-01

    II Tape History 111-3 111-2 High and Low Flow Lag Times 111-17 111-3 Fixes for Recurring Negative Inflows 111-21 IV-l Periods of Record of New York...00000 00000 00 - 00000 00000 00 0.= 0. U *00000 cacao 00 E 0 U Li.. IA. 0*00.0 00*00 NC C onto can.n. *0 O 00000 00000 00 .0 U 00000 00000 0000 0. EU0...As expected, 1964-1966 was the worst event in the 50 year history . The 25th worst annual event, June 1, 1935 to May 31, 1936 is an average year. The

  7. The Hans Tausen drill

    DEFF Research Database (Denmark)

    Johnsen, Sigfus Johann; Dahl-Jensen, Dorthe; Steffensen, Jørgen Peder

    2007-01-01

    In the mid-1990s, excellent results from the GRIP and GISP2 deep drilling projects in Greenland opened up funding for continued ice-coring efforts in Antarctica (EPICA) and Greenland (NorthGRIP). The Glaciology Group of the Niels Bohr Institute, University of Copenhagen, was assigned the task...... of providing drilling capability for these projects, as it had done for the GRIP project. The group decided to further simplify existing deep drill designs for better reliability and ease of handling. The drill design decided upon was successfully tested on Hans Tausen Ice Cap, Peary Land, Greenland, in 1995....... The 5.0 m long Hans Tausen (HT) drill was a prototype for the ~11 m long EPICA and NorthGRIP versions of the drill which were mechanically identical to the HT drill except for a much longer core barrel and chips chamber. These drills could deliver up to 4 m long ice cores after some design improvements...

  8. Integral analysis of the drill string dynamic behaviour to optimize drilling operation; Analise integrada do comportamento dinamico da coluna para otimizacao de perfuracao

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Araken [Smith International do Brasil, Macae, RJ (Brazil); Placido, Joao C.R.; Percy, Joseir G.; Falcao, Jose; Freire, Helena; Ono, Eduardo H.; Masculo, Miguel S. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Azuaga, Denise; Frenzel, Mark [Smith International Inc., Houston, TX (United States)

    2008-07-01

    For a performance preview of a drilling system is necessary a dynamic and integrated modeling for understanding all system forces resulting from the combination of the rock strength, cut structure action, drilling parameters, BHA and all others drilling components. This study must predict, for the drill string, vibrations and torsions, from bit to surface, its origins and its effects, and provides the best way to reduce these vibrations, determining the best bit, BHA and drilling parameters. Thereby, this study eliminates the trial and error approach and the operation risks. This paper aims to present studies of optimization for two drilling wells conducted in Brazil, one in Santos Basin and other in Campos Basin, and compares the numerical simulations results with the data from drilling operations. (author)

  9. Joint Rescue Drill

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Ships gather for a joint rescue drill at the Waigaoqiao Dock in Shanghai on August 24.A large-scale rescue drill, combining maritime and air forces,was held as part of the ongoing World Maritime Rescue Conference 2011 in the city.During the drill,

  10. Fourth Summative Report of the Delaware PLATO Project.

    Science.gov (United States)

    Hofstetter, Fred T.

    A brief history of the Delaware PLATO project and descriptions of new developments in facilities, applications, user services, research, evaluation, and courseware produced since the Third Summative Report (1978) are provided, as well as an overview of PLATO applications at the University of Delaware. Sample lessons, illustrations, and activity…

  11. Fifth Summative Report of the Delaware PLATO Project.

    Science.gov (United States)

    Hofstetter, Fred T.

    A brief history of the Delaware PLATO project and descriptions of the new developments in facilities, applications, user services, research, evaluation, and courseware produced since the Fourth Summative Report (1979) are provided, as well as an overview of PLATO applications at the University of Delaware. Sample lessons, illustrations, and…

  12. 18 CFR 410.1 - Basin regulations-Water Code and Administrative Manual-Part III Water Quality Regulations.

    Science.gov (United States)

    2010-04-01

    ... Code and Administrative Manual-Part III Water Quality Regulations. 410.1 Section 410.1 Conservation of Power and Water Resources DELAWARE RIVER BASIN COMMISSION ADMINISTRATIVE MANUAL BASIN REGULATIONS; WATER CODE AND ADMINISTRATIVE MANUAL-PART III WATER QUALITY REGULATIONS § 410.1 Basin regulations—Water Code...

  13. The Courts, the Legislature, and Delaware's Resegregation: A Report on School Segregation in Delaware, 1989-­2010

    Science.gov (United States)

    Niemeyer, Arielle

    2014-01-01

    Delaware's history with school desegregation is complicated and contradictory. The state both advanced and impeded the goals of "Brown v. Board of Education." After implementing desegregation plans that were ineffective by design, Delaware was ultimately placed under the first metropolitan, multi-district desegregation court order in the…

  14. Western Gas Sands Project. Quarterly basin activities report, October 1-December 31, 1979

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-01

    This report is a summation of three months drilling and testing activitie in the four primary study areas of the WGSP: Greater Green River Basin, Northern Great Plains Province, Piceance Basin, and Uinta Basin.

  15. Metal and hydrocarbon behavior in sediments from Brazilian shallow waters drilling activities using nonaqueous drilling fluids (NAFs).

    Science.gov (United States)

    do Carmo R Peralba, Maria; Pozebon, Dirce; dos Santos, João H Z; Maia, Sandra M; Pizzolato, Tânia M; Cioccari, Giovani; Barrionuevo, Simone

    2010-08-01

    The impact of drilling oil activities in the Brazilian Bonito Field/Campos Basin (Rio de Janeiro) shell drilling (300 m) using nonaqueous fluids (NAFs) was investigated with respect to Al, Fe, Mn, Ba, Co, Pb, Cu, As, Hg, Cr, Ni, Zn, Cd, V, and aliphatic and polynuclear aromatic hydrocarbons concentrations in the sediment. Sampling took place in three different times during approximately 33 months. For the metals Al, As, Co, Cr, Cu, Cd, Fe, Ni, Mn, V, and Zn, no significant variation was observed after drilling activities in most of the stations. However, an increase was found in Ba concentration--due to the drilling activity--without return to the levels found 22 months after drilling. High Ba contents was already detected prior to well drilling, probably due to drilling activities in other wells nearby. Hydrocarbon contents also suggest previous anthropogenic activities. Aliphatic hydrocarbon contents were in the range usually reported in other drilling sites. The same behavior was observed in the case of polyaromatic hydrocarbons. Nevertheless, the n-alkane concentration increased sharply after drilling, returning almost to predrilling levels 22 months after drilling activities.

  16. Advanced Oil Recovery Technologies for Improved Recovery from Slope Basin Clastic Reservoirs, Nash Draw Brushy Canyon Pool, Eddy County, NM

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, Mark B.

    1999-02-24

    The Nash Draw Brushy Canyon Pool in Eddy County New Mexico is a cost-shared field demonstration project in the US Department of Energy Class II Program. A major goal of the Class III Program is to stimulate the use of advanced technologies to increase ultimate recovery from slope-basin clastic reservoirs. Advanced characterization techniques are being used at the Nash Draw project to develop reservoir management strategies for optimizing oil recovery from this Delaware reservoir. Analysis, interpretation, and integration of recently acquired geologic, geophysical, and engineering data revealed that the initial reservoir characterization was too simplistic to capture the critical features of this complex formation. Contrary to the initial characterization, a new reservoir description evolved that provided sufficient detail regarding the complexity of the Brushy Canyon interval at Nash Draw. This new reservoir description is being used as a risk reduction tool to identify ''sweet spots'' for a development drilling program as well as to evaluate pressure maintenance strategies. The reservoir characterization, geological modeling, 3-D seismic interpretation, and simulation studies have provided a detailed model of the Brushy Canyon zones. This model was used to predict the success of different reservoir management scenarios and to aid in determining the most favorable combination of targeted drilling, pressure maintenance, well simulation, and well spacing to improve recovery from this reservoir.

  17. Water vapor transport in the Pearl River basin and its influence on NDVI

    Directory of Open Access Journals (Sweden)

    Wang Yin-Xia

    2016-01-01

    Full Text Available Using NECP/NCAR monthly average data and 216 months average monthly precipitation data of the University of Delaware during 1982-1999. Analyzed the precipitation vapour transport process affects precipitation in the Pearl River Basin in different seasons. On this basis, the seasonal differences NDVI changes in climate-driven factors in the Pearl River Basin.

  18. Quality in drilling operations

    Energy Technology Data Exchange (ETDEWEB)

    Duncan, E.; Gervais, I. [Sedco Forex Jacintoport Facility, Channelview, TX (United States); Le Moign, Y.; Pangarkar, S.; Stibbs, B. [Sedco Forex, Montrouge (France); McMorran, P. [Sedco Forex, Pau (France); Nordquist, E. [Dubai Petroleum Company, Dubai (United Arab Emirates); Pittman, T. [Sedco Forex, Perth (Australia); Schindler, H. [Sedco Forex, Dubai (United Arab Emirates); Scott, P. [Woodside Offshore Petroleum Pty. Ltd., Perth (Australia)

    1996-12-31

    Driven by cost and profitability pressures, quality has taken on new meaning and importance in the oil field during the past decade. In drilling operations, new initiatives have led to cooperative team efforts between operators and drilling contractors to enhance quality. In this article examples are given of how one drilling contractor, by adopting a quality culture, is reaping major benefits for its clients as well as its employees. 22 figs., 19 refs.

  19. Drilling cost-cutting

    Energy Technology Data Exchange (ETDEWEB)

    Capuano, L.E. Jr.

    1996-12-31

    This presentation by Louis E. Capuano, Jr., President, ThermaSource, Inc., discusses cost-cutting in the drilling phase of geothermal energy exploration and production. All aspects of a geothermal project including the drilling must be streamlined to make it viable and commercial. If production could be maximized from each well, there would be a reduction in drilling costs. This could be achieved in several ways, including big hole and multi-hole completion, directional drilling, better knowledge of the resource and where to penetrate, etc.

  20. Horizontal drilling in Ontario

    Energy Technology Data Exchange (ETDEWEB)

    Sidey, P.; Precul, L. [Sproule Associates Ltd., Calgary, AB (Canada)

    2002-07-01

    A review of oil and gas production in Ontario was presented with particular reference to drilling activity between 1987 to mid 2002 when 1450 vertical wells were drilled, of which 1100 were for petroleum production and the remainder were for gas storage, observation wells, private gas wells and stratigraphic tests. Of the 1100 vertical wells drilled for petroleum production, 40 per cent became gas wells, 16 per cent became oil wells, 4 per cent became oil and gas wells, and 40 per cent were dry. During the same time period, 133 horizontal wells were also drilled, mostly for petroleum. The most active operator was Talisman Energy, which drilled 101 of the 133 horizontal wells. The remainder were drilled by 12 other companies. Of the horizontal wells, 64 per cent became oil wells, 19 per cent became gas wells, and 17 per cent were dry. This presentation included graphs depicting which oil and gas pools saw vertical or horizontal drilling during the designated time period, and explained how the wells were classified. Both horizontal and vertical well targets were illustrated. Particular reference was made to Talisman Energy's Lake Erie Drilling program which revealed that horizontal wells have an initial production rate that is 5 times that expected from vertical wells. The Hillman Pool case study revealed that the initial rate of the average horizontal well is less than half that of the average vertical well. Horizontal drilling in the Lake Erie Morpeth Gas pool has also been a commercial success. This paper demonstrates that operators have maintained Ontario's oil and gas production at high levels. In 1997 widespread horizontal drilling began taking place in Ontario, and since then, approximately 30 per cent of the wells drilled in the province have been horizontal. 16 figs.

  1. 2007 Delaware Coastal Programs Lidar: Kent and New Castle Counties

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The data acquisition occurred in 7 missions between March 31 and April 5, 2007 in Kent and New Castle Counties, Delaware. The data have been classified and were...

  2. NOAA Ship Delaware II Underway Meteorological Data, Quality Controlled

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA Ship Delaware II Underway Meteorological Data (delayed ~10 days for quality control) are from the Shipboard Automated Meteorological and Oceanographic System...

  3. 2007 Delaware Coastal Program Lidar: Kent and New Castle Counties

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The data acquisition occurred in 7 missions between March 31 and April 5, 2007 in Kent and New Castle Counties, Delaware. The data have been classified and were...

  4. Drilling Optimization: A Review

    Directory of Open Access Journals (Sweden)

    Abhilash M Bharadwaj

    2013-06-01

    Full Text Available With rapidly growing global demand for energy resources, oil and gas exploration & production companies face mounting pressure to maximize supply and increase the rate of discovery for new energy sources. Increasingly operating in more remote locations and investing heavily in equipment and facilities, companies face greater financial and operational risks than ever before. Optimization of drilling parameters during drilling operations aims to optimize weight on bit, bit rotation speed for obtaining maximum drilling rate as well as minimizing the drilling cost. Communication and computer technologies are among the most important disciplines which can contribute to drilling optimization. Large amount of data could be piped through different locations on the planet in reliable and time efficient manners.

  5. Distributed downhole drilling network

    Science.gov (United States)

    Hall, David R.; Hall, Jr., H. Tracy; Fox, Joe; Pixton, David S.

    2006-11-21

    A high-speed downhole network providing real-time data from downhole components of a drilling strings includes a bottom-hole node interfacing to a bottom-hole assembly located proximate the bottom end of a drill string. A top-hole node is connected proximate the top end of the drill string. One or several intermediate nodes are located along the drill string between the bottom-hole node and the top-hole node. The intermediate nodes are configured to receive and transmit data packets transmitted between the bottom-hole node and the top-hole node. A communications link, integrated into the drill string, is used to operably connect the bottom-hole node, the intermediate nodes, and the top-hole node. In selected embodiments, a personal or other computer may be connected to the top-hole node, to analyze data received from the intermediate and bottom-hole nodes.

  6. Drilling Optimization: A Review

    Directory of Open Access Journals (Sweden)

    Vinayaka S

    2012-08-01

    Full Text Available With rapidly growing global demand for energy resources, oil and gas exploration & production companies face mounting pressure to maximize supply and increase the rate of discovery for new energy sources. Increasingly operating in more remote locations and investing heavily in equipment and facilities, companies face greater financial and operational risks than ever before. Optimization of drilling parameters during drilling operations aims to optimize weight on bit, bit rotation speed for obtaining maximum drilling rate as well as minimizing the drilling cost. Communication and computer technologies are among the most important disciplines which can contribute to drilling optimization. Large amount of data could be piped through different locations on the planet in reliable and time efficient manners.

  7. Advanced drilling systems study.

    Energy Technology Data Exchange (ETDEWEB)

    Pierce, Kenneth G.; Livesay, Billy Joe; Finger, John Travis (Livesay Consultants, Encintas, CA)

    1996-05-01

    This report documents the results of a study of advanced drilling concepts conducted jointly for the Natural Gas Technology Branch and the Geothermal Division of the U.S. Department of Energy. A number of alternative rock cutting concepts and drilling systems are examined. The systems cover the range from current technology, through ongoing efforts in drilling research, to highly speculative concepts. Cutting mechanisms that induce stress mechanically, hydraulically, and thermally are included. All functions necessary to drill and case a well are considered. Capital and operating costs are estimated and performance requirements, based on comparisons of the costs for alternative systems to conventional drilling technology, are developed. A number of problems common to several alternatives and to current technology are identified and discussed.

  8. Fifteen years of the Chinese Continental Scientific Drilling Program

    Science.gov (United States)

    Xu, Zhiqin; Yang, Jingsui; Wang, Chengshan; An, Zhisheng; Li, Haibing; Wang, Qin; Su, Dechen

    2017-05-01

    Continental scientific drilling can be regarded as a telescope into the Earth's interior because it provides process insight and uncompromised samples of rocks, fluids, and even sampled from the deep biosphere from the Earth's surface to great depths. As one of the three founding members of the International Continental Scientific Drilling Program (ICDP), ICDP China has made great achievements in many scientific drilling-related research fields. Based on the ICDP participation it attracted global attention of scientists and set up not only the Chinese Continental Scientific Drilling (CCSD) Program in 2001 but also a growing number of ambitious drilling projects in the country. The 5158 m deep borehole of the CCSD project at Donghai County in the Sulu ultrahigh-pressure metamorphic terrain demonstrates that large amounts of crustal rocks of the South China Block have been subducted to at least 120 km, followed by rapid uplift. After successful completion of drilling at Donghai, several continental scientific drilling projects were conducted with funding of the Chinese government and partially with support of ICDP, resulting in a total drilling depth of more than 35 000 m. These projects encompass the Continental Environmental Scientific Drilling Program of China, the Scientific Drilling Project of Wenchuan Earthquake Fault Zone, the Continental Scientific Drilling Project of Cretaceous Songliao Basin, and the Program of Selected Continental Scientific Drilling and Experiments. On the occasion of the 20th anniversary of the ICDP and the 15th anniversary of the CCSD Program, this paper reviews the history and major progress of the CCSD Program.

  9. Drilling fluid technologies : what goes in must come out

    Energy Technology Data Exchange (ETDEWEB)

    Polczer, S.

    1998-03-01

    The treatment of drilling wastes contaminated with invert drilling muds was discussed. The tight emulsion properties which make invert drilling muds useful are the same properties that make their disposal so difficult. Potential long-term liability associated with inverts is another reason for reluctance to use these products. Inverts are toxic and highly mobile in the environment, and must therefore be handled with care. Often the costs associated with their disposal are greater than their potential benefits. Petro-Canada Lubricants has formulated a new, non-diesel based product called Drill Mud Oil HT40N which completely eliminates toxic aromatic molecules. It is composed of 98 per cent plus of cyclic and branched isoparaffins with an average carbon number of C16. The level of polynuclear aromatics is reduced to parts per billion levels. Drill Mud Oil HT40N was being used at Hibernia until an even newer product, IPAR3 synthetic drill mud oil, was developed exclusively for offshore use. Drill Mud Oil HT40N is less prone to flash fires, is odourless and is more likely to be used in places such as the Western Canada Sedimentary Basin. Drill Mud Oil HT40N works almost exactly the same as a diesel-based drill mud oil but has many advantages in terms of safety and ease of disposal, particularly in landfarming operations. Drill Mud Oil HT40N does not irritate the skin or release toxic fumes. The cost of Drill Mud Oil HT40N is higher than conventional diesel-based drilling muds. 2 figs.

  10. 33 CFR 162.40 - Inland waterway from Delaware River to Chesapeake Bay, Del. and Md. (Chesapeake and Delaware Canal).

    Science.gov (United States)

    2010-07-01

    ...., between Reedy Point, Delaware River, and Old Town Point Wharf, Elk River. (b) Speed. No vessel in the..., are required to travel at all times at a safe speed throughout the canal and its approaches so as to...

  11. Western Gas Sands Project Quarterly Basin Activities Report

    Energy Technology Data Exchange (ETDEWEB)

    Atkinson, C H

    1979-04-30

    This quarterly basin activities report is a summation of three months drilling and testing activities in the Greater Green River Basin, Northern Great Plains Province, Piceance Basin, and Uinta Basin. Detailed information is given for each study area for the first quarter of 1979.

  12. Western Gas Sands Project. Quarterly Basin Activities Report

    Energy Technology Data Exchange (ETDEWEB)

    Atkinson, C H

    1979-01-31

    This report is a summation of 3 months' drilling and testing activities in the four primary WGSP study areas: Greater Green River Basin, Northern Great Plains Province, Piceance Basin, and Uinta Basin. The monitoring of basin activities is part of resource assessment. (DLC)

  13. Results of coalbed-methane drilling, Meadowfill Landfill, Harrison County, West Virginia: Chapter G.4 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Science.gov (United States)

    Ruppert, Leslie F.; Trippi, Michael H.; Fedorko, Nick; Grady, William C.; Eble, Cortland F.; Schuller, William A.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    The U.S. Environmental Protection Agency funded drilling of a borehole (39.33889°N., 80.26542°W.) to evaluate the potential of enhanced coalbed-methane production from unminable Pennsylvanian coal beds at the Meadowfill Landfill near Bridgeport, Harrison County, W. Va. The drilling commenced on June 17, 2004, and was completed on July 1, 2004. The total depth of the borehole was 1,081 feet (ft) and contained 1,053.95 ft of Pennsylvanian coal-bearing strata, and 27.05 ft of Mississippian strata.

  14. Drilling and well technology

    Energy Technology Data Exchange (ETDEWEB)

    Milheim, K. [Mining University Leoben Institute for Drilling Technology, (Austria)

    1996-12-31

    Over a billion dollars a year is lost by exploration and production companies drilling wells because of the lack of learn curve management (LMC) practices. This paper presents the importance of the LMC concept, what it is, why LMC has not yet been recognized as a major initiative for improving drilling cost performance. The paper discusses the different types of planning, problems with implementation of plans, the use and misuse of drilling results and data bases, and the lack of post analysis practices. The major point of the paper is to show the massive savings that can be achieved by valuing LMC, learning LMC and successfully implementing LMC. . 2 refs., 5 figs.

  15. 76 FR 11812 - Drill Pipe and Drill Collars From China

    Science.gov (United States)

    2011-03-03

    ... Register on September 9, 2010 (75 FR 54912). The hearing was held in Washington, DC, on January 5, 2011... COMMISSION Drill Pipe and Drill Collars From China Determinations On the basis of the record \\1\\ developed in... of imports of drill pipe and drill collars from China, provided for in subheadings 7304.22,...

  16. 75 FR 10501 - Drill Pipe and Drill Collars from China

    Science.gov (United States)

    2010-03-08

    ... publishing the notice in the Federal Register of January 6, 2010 (75 FR 877). The conference was held in... COMMISSION Drill Pipe and Drill Collars from China Determinations On the basis of the record \\1\\ developed in... injury by reason of imports from China of drill pipe and drill collars, provided for in subheadings...

  17. Cost-Effectiveness Analysis of the Residential Provisions of the 2015 IECC for Delaware

    Energy Technology Data Exchange (ETDEWEB)

    Mendon, Vrushali V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhao, Mingjie [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Taylor, Zachary T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Poehlman, Eric A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-02-15

    The 2015 IECC provides cost-effective savings for residential buildings in Delaware. Moving to the 2015 IECC from the 2012 IECC base code is cost-effective for residential buildings in all climate zones in Delaware.

  18. 75 FR 76036 - Charming Shoppes of Delaware, Inc. Accounts Payable, Rent, Merchandise Disbursement Divisions...

    Science.gov (United States)

    2010-12-07

    ... Employment and Training Administration Charming Shoppes of Delaware, Inc. Accounts Payable, Rent, Merchandise... of Charming Shoppes of Delaware, Inc., including the Accounts Payable, Rent, and Merchandise... the same division, are engaged in activities related to the supply of accounts payable,...

  19. 75 FR 54026 - Safety Zone; Red Bull Flugtag, Delaware River, Camden, NJ

    Science.gov (United States)

    2010-09-03

    ... safety zone in an area of the Delaware River, Camden, NJ, described as North of the Wiggins park Marina... traffic from navigating on the Delaware River in an area described as north of the Wiggins Park Marina...

  20. Flood Plain Information, Delhi New York, West Branch Delaware River and Little Delaware River.

    Science.gov (United States)

    1974-06-01

    1,383.9 1,382.4 1,391.3 Little Delaware River Back River Road 0.15 1,346.4 1,346.9 1,352.1 College Golf Course Footbridge 0.28 1,349.4 1,350.0 1,353.2...College Golf Course Footbridge 0.36 1,353.7 1,353.6 1,356.1 Bridge by USGS Gaging Station 1.79 1,395.9 1,396.9 1,403.6 N.Y. Rte. 28 5.93 1,533.9

  1. Nonpolluting drilling fluid composition

    Energy Technology Data Exchange (ETDEWEB)

    Larson, D.E.; Mocek, C.J.; Mouton, R.J.

    1983-02-22

    Disclosed is a nonpolluting drilling fluid composition. The composition mixture consisting essentially of a concentrate and any nonpolluting oil. The concentrate consists essentially of diethanolamide, a fatty acid, and a imidazoline/amide mixture.

  2. Smoke-free law did affect revenue from gaming in Delaware

    OpenAIRE

    Michael R. Pakko

    2005-01-01

    A paper recently published in the journal Tobacco Control purports to show that the implementation of a smoking prohibition in Delaware had no statistically significant effect on the revenues of three gaming facilities in that state. After correcting for evident errors in that analysis, I find that the smoke-free law did affect revenues from gaming in Delaware. Total gaming revenues are estimated to have declined by at least $6 million per month after the implementation of Delaware*s Clean In...

  3. Continental Scientific Drilling Program.

    Science.gov (United States)

    1979-01-01

    Resource Priorities in Continental Drilling J. J. Hemley 12 Aspects of Continental Crustal Structure and Growth Scott Smithson 13 Deep-Drilling Targets...Time of Workshop Allen F. Agnew Library of Congress Clarence R. Allen California Institute of Technology Orson L. Anderson University of California at...Skinner Yale University Norman H. Sleep Northwestern University Laurence L. Sloss Northwestern University Scott B. Smithson University of Wyoming

  4. Application program of CRUST-1 10km continental scientific drilling rig in SK-2 scientific drilling well

    Science.gov (United States)

    Sun, Youhong; Gao, Ke; Yu, Ping; Liu, Baochang; Guo, Wei; Ma, Yinlong; Yang, Yang

    2014-05-01

    SK-2 Well is located in DaQing city,where is site of the largest oil field in China,Heilongjiang province, north-east of China.The objective of SK-2 well is to obtain full cores of cretaceous formation in Song Liao basin,and to build the time tunnel of Cretaceous greenhouse climate change,and to clarify the causes,processes and results of the formations of DaQing oil field. This will ensure to achieve our ultimate goals,to test the CRUST-1 drilling rig and improve China's deep scientific drilling technology,to form the scientific drilling technology,method and system with independent intellectual property rights,and to provide technical knowledge and information for China's ten kilometers super-deep scientific drilling technical resources.SK-2 Well is at 6400 meter depth, where the drilling inclination is 90 degree and the continuous coring length is 3535 meter that from 2865 to 6400 meter,the recovery rate of the core is greater or equal to 95 percent with 100 millimeters core diameter and 3.9 degree per 100 meter geothermal gradient.The CRUST-1 rig is designated with special drilling equipment for continental scientific drilling combined to the oil drilling equipment ability with advanced geological drilling technology which is highly automatic and intelligent. CRUST-1 drilling ability is 10000 meter with the maximum hook load 700 tons, the total power is 4610 Kilowatt.CRUST-1 will be integrated with a complete set of automation equipment,including big torque hydraulic top drive,high accuracy automatic drilling rod feeding system, suspended automatic drill string discharge device,hydraulic intelligent iron roughneck,and hydraulic automatic catwalk to fully meet the drilling process requirements of SK-2.Designed with advanced drilling technique for 260 degree in the bottom of SK-2 well and hard rock,including the drilling tools of high temperature hydraulic hammer,high temperature resistance and high strength aluminum drill pipe,high temperature preparation of mud

  5. 78 FR 4167 - Commercial Wind Lease Issuance on the Atlantic Outer Continental Shelf Offshore Delaware

    Science.gov (United States)

    2013-01-18

    ... Offshore Delaware. SUMMARY: BOEM has issued a commercial wind energy lease to Bluewater Wind Delaware LLC... Bureau of Ocean Energy Management Commercial Wind Lease Issuance on the Atlantic Outer Continental Shelf Offshore Delaware AGENCY: Bureau of Ocean Energy Management (BOEM), Interior. ACTION: Notice...

  6. Paramagnetism shielding in drilling fluid

    OpenAIRE

    Li,Zhuo

    2013-01-01

    In drilling operations, drilling fluid containing magnetic materials is used when drilling a well. The materials can significantly shield the Earth’s magnetic field as measured by magnetic sensors inside the drilling strings. The magnetic property of the drilling fluid is one of the substantial error sources for the determination of magnetic azimuth for wellbores. Both the weight material, cuttings, clay and other formation material plus metal filings from the tubular wear m...

  7. Modeling pellet impact drilling process

    OpenAIRE

    Kovalev, Artem Vladimirovich; Ryabchikov, Sergey Yakovlevich; Isaev, Evgeniy Dmitrievich; Ulyanova, Oksana Sergeevna

    2016-01-01

    The paper describes pellet impact drilling which could be used to increase the drilling speed and the rate of penetration when drilling hard rocks. Pellet impact drilling implies rock destruction by metal pellets with high kinetic energy in the immediate vicinity of the earth formation encountered. The pellets are circulated in the bottom hole by a high velocity fluid jet, which is the principle component of the ejector pellet impact drill bit. The experiments conducted has allowed modeling t...

  8. Application on drilling parameter monitor in drilling engineering monitoring

    Institute of Scientific and Technical Information of China (English)

    Shu DIAO; Zhenbao LING; Wenjing LIANG

    2008-01-01

    The drilling parameter monitor is an important tool in drilling engineering applied to monitoring drilling process, carrying out scientific analysis and decision-making. Based on discussing the present development situation of the domestic and foreign drilling machine parameter monitors, the metering scheme for vehicle-loaded drilling parameter monitor was designed. By using detection system for MSP430 single-chip microcomputer (SCM) in combination with peripheral circuit such as sensors, the drilling-rig control system was obtained to detect, and for every parameter in real-time display in order to keep operating the drilling rig status. The experiment shows that the drilling parameter monitor reaches design requirements and can be applied to drilling engineering monitoring, which has characters such as simple structure, high credibility and low cost.

  9. Horizontal Directional Drilling (HDD) Technology and Applications

    Institute of Scientific and Technical Information of China (English)

    J. G. Cai; X. N. Wang

    2004-01-01

    @@ 1 What is Horizontal Directional Drilling? Horizontal Directional Drilling, accurately steered drilling, has become state -of- the -art drilling technique in the world. Specially- designed directionsteerable corebarrel and accurate direction measurement tool are available for the use together with wire line core drilling machine. That makes it feasible to extract cores and to measure the drill travel line &length while drilling in a curve.

  10. Evacuation drill at CMS

    CERN Multimedia

    Niels Dupont-Sagorin and Christoph Schaefer

    2012-01-01

    Training personnel, including evacuation guides and shifters, checking procedures, improving collaboration with the CERN Fire Brigade: the first real-life evacuation drill at CMS took place on Friday 3 February from 12p.m. to 3p.m. in the two caverns located at Point 5 of the LHC.   CERN personnel during the evacuation drill at CMS. Evacuation drills are required by law and have to be organized periodically in all areas of CERN, both above and below ground. The last drill at CMS, which took place in June 2007, revealed some desiderata, most notably the need for a public address system. With this equipment in place, it is now possible to broadcast audio messages from the CMS control room to the underground areas.   The CMS Technical Coordination Team and the GLIMOS have focused particularly on preparing collaborators for emergency situations by providing training and organizing regular safety drills with the HSE Unit and the CERN Fire Brigade. This Friday, the practical traini...

  11. Chinese Drilling Crews Active Worldwide

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    @@ China Great Wall Drilling Company signed a US$5 million contract with Tunis Joint Venture Petroleum Company in late April for drilling five wells in the middle coastal area of Tunis. This is the first time Tunis has invited the tenders from foreign companies for a drilling project. The participants in the bidding include other 11 drilling companies from the United States, Australia, Croatia and other countries. The drilling operation is expected to start from June this year. Founded in 1995, Great Wall Drilling Company is a subsidiary of CNPC International Engineering Company. The drilling company is now operating more than 50 Chinesemade drilling rigs overseas and involved in the drilling projects in 15 countries and regions such as Sudan, Iran, Indonesia, Egypt, Canada, Kazakhstan,Venezuela and other countries. The Tunis project is the 15th one of the company.

  12. Computer monitors drilling performance

    Energy Technology Data Exchange (ETDEWEB)

    1984-05-01

    Computer systems that can monitor over 40 drilling variables, display them graphically, record and transmit the information have been developed separately by two French companies. The systems, Vigigraphic and Visufora, involve the linking of a master computer with various surface and downhole sensors to measure the data on a real-time (as experienced) basis and compute the information. Vigigraphic is able to produce graphic displays grouped on four screens - drilling, tripping, geological and mud data. It computes at least 200 variables from the sensor readings, and it can store over 100 variables. Visufora allows the operator to group the drilling variables as desired. It can monitor and analyze surface and downhole parameters. The system can be linked with MWD tools. Twenty channels of input are assigned to surface values and the remaining 20 channels can be used to monitor downhole instrumentation.

  13. The Oman Drilling Project

    Science.gov (United States)

    Matter, J.; Kelemen, P. B.; Teagle, D. A. H.

    2014-12-01

    With seed funds from the Sloan Foundation, the International Continental Drilling Program (ICDP) approved a proposal by 39 international proponents for scientific drilling in the Oman ophiolite. Via observations on core, geophysical logging, fluid sampling, hydrological measurements, and microbiological sampling in a series of boreholes, we will address long-standing, unresolved questions regarding melt and solid transport in the mantle beneath oceanic spreading ridges, igneous accretion of oceanic crust, mass transfer between the oceans and the crust via hydrothermal alteration, and recycling of volatile components in subduction zones. We will undertake frontier exploration of subsurface weathering processes in mantle peridotite, including natural mechanisms of carbon dioxide uptake from surface waters and the atmosphere, and the nature of the subsurface biosphere. Societally relevant aspects include involvement and training of university students, including numerous students from Sultan Qaboos University in Oman. Studies of natural mineral carbonation will contribute to design of engineered systems for geological carbon dioxide capture and storage. Studies of alteration will contribute to fundamental understanding of the mechanisms of reaction-driven cracking, which could enhance geothermal power generation and extraction of unconventional hydrocarbon resources. We hope to begin drilling in late 2015. Meanwhile, we are seeking an additional $2M to match the combined Sloan and ICDP funding from national and international funding agencies. Matching funds are needed for operational costs of drilling, geophysical logging, downhole fluid sampling, and core description. Information on becoming part of the named investigator pool is in Appendix 14 (page 70) of the ICDP proposal, available at https://www.ldeo.columbia.edu/gpg/projects/icdp-workshop-oman-drilling-project. This formal process should begin at about the time of the 2014 Fall AGU Meeting. Meanwhile, potential

  14. Drilling comparison in "warm ice" and drill design comparison

    DEFF Research Database (Denmark)

    Augustin, L.; Motoyama, H.; Wilhelms, F.

    2007-01-01

    at each site, the drilling rate dropped and the drilling teams had to deal with refrozen ice on cutters and drill heads. Drills have different limits and perform differently. In this comparative study, we examine depth, pressure, temperature, pump flow and cutting speed. Finally, we compare a few......For the deep ice-core drilling community, the 2005/06 Antarctic season was an exciting and fruitful one. In three different Antarctic locations, Dome Fuji, EPICA DML and Vostok, deep drillings approached bedrock (the ice-water interface in the case of Vostok), emulating what had previously been...... achieved at NorthGRIP, Greenland, (summer 2003 and 2004) and at EPICA Dome C2, Antarctica (season 2004/05). For the first time in ice-core drilling history, three different types of drill (KEMS, JARE and EPICA) simultaneously reached the depth of 'warm ice' under high pressure. After excellent progress...

  15. Algebra task & drill sheets

    CERN Document Server

    Reed, Nat

    2011-01-01

    For grades 6-8, our State Standards-based combined resource meets the algebraic concepts addressed by the NCTM standards and encourages the students to review the concepts in unique ways. The task sheets introduce the mathematical concepts to the students around a central problem taken from real-life experiences, while the drill sheets provide warm-up and timed practice questions for the students to strengthen their procedural proficiency skills. Included are opportunities for problem-solving, patterning, algebraic graphing, equations and determining averages. The combined task & drill sheets

  16. Algebra task & drill sheets

    CERN Document Server

    Reed, Nat

    2011-01-01

    For grades 3-5, our State Standards-based combined resource meets the algebraic concepts addressed by the NCTM standards and encourages the students to review the concepts in unique ways. The task sheets introduce the mathematical concepts to the students around a central problem taken from real-life experiences, while the drill sheets provide warm-up and timed practice questions for the students to strengthen their procedural proficiency skills. Included are opportunities for problem-solving, patterning, algebraic graphing, equations and determining averages. The combined task & drill sheets

  17. Drill on Android

    OpenAIRE

    2013-01-01

    HES-SO DRILLER est une application de drill disponible sur Cyberlearn qui permet aux utilisateurs d’effectuer des quizz relatifs à la programmation. Le principe étant que les professeurs créent leurs quizz et les étudiants puissent y jouer. Les scores obtenus sont comptabilisés et comparés sur Facebook. Ce projet a pour but d’analyser cette application et de l’adapter afin de l’utiliser sur un client mobile Android sous le nom de Drill on Android.

  18. Results of coalbed-methane drilling, Mylan Park, Monongalia County, West Virginia: Chapter G.3 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Science.gov (United States)

    Ruppert, Leslie F.; Fedorko, Nick; Warwick, Peter D.; Grady, William C.; Britton, James Q.; Schuller, William A.; Crangle, Robert D.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    The Department of Energy National Energy Technology Laboratory funded drilling of a borehole (39.64378°N., 80.04376°W.) to evaluate the potential for coalbed-methane and carbon-dioxide sequestration at Mylan Park, a public park in Monongalia County, W. Va. The total depth of the borehole was 2,525 feet (ft) and contained 1,483.41 ft of Pennsylvanian coal-bearing strata, 739.67 ft of Mississippian strata, and 301.93 ft of Devonian strata.

  19. Drill string corrosion problems at Pilar field; Corrosao na coluna de perfuracao no Campo de Pilar

    Energy Technology Data Exchange (ETDEWEB)

    Guimaraes, Antimio Santos [PETROBRAS, XX (Brazil). Distrito de Perfuracao do Nordeste. Setor de Fluidos de Perfuracao

    1988-12-31

    Drilling column failures and washout problems are described as experienced in the Sergipe-Alagoas Basin`s Pilar field. Statistical data presented indicate the extent of this problem. A discussion is offered on causes detected and solutions adopted. (author) 3 refs., 16 figs.

  20. Deep Drilling Technology of China

    Institute of Scientific and Technical Information of China (English)

    Ni Rongfu

    1995-01-01

    @@ Since the drilling of well Songji-6 by the drilling crew No. 32139 in Daqing in 1963,there havebeen some 1600 over 4 000 m deep wells completed till 1993, among which two are above 7 000 m in depth.

  1. Intelligent Detection of Drill Wear

    Science.gov (United States)

    Liu, T. I.; Chen, W. Y.; Anatharaman, K. S.

    1998-11-01

    Backpropagation neural networks (BPNs) were used for on-line detection of drill wear. The neural network consisted of three layers: input, hidden, and output. The input vector comprised drill size, feed rate, spindle speed, and eight features obtained by processing the thrust and torque signals. The output was the drill wear state which either usable or failure. Drilling experiments with various drill sizes, feed rates and spindle speeds were carried out. The learning process was performed effectively by utilising backpropagation with smoothing and an activation function slope. The on-line detection of drill wear states using BPNs achieved 100% reliability even when the drill size, feed rate and spindle speed were changed. In other words, the developed on-line drill wear detection systems have very high robustness and hence can be used in very complex production environments, such as flexible manufacturing systems.

  2. 27 CFR 9.49 - Central Delaware Valley.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Central Delaware Valley. 9.49 Section 9.49 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU.... (ix) From there northward along Covered Bridge Road to Green Sergeant Covered Bridge. (x) From...

  3. Sex, Lies, and Residence Life: Delaware's Thought Reform

    Science.gov (United States)

    Kissel, Adam

    2009-01-01

    The University of Delaware has a zero-tolerance policy for anything remotely resembling "hate speech." As such, the school implemented a mandatory training for all 7,000-odd students in its dorms. The sessions were part of a thorough thought-reform curriculum, designed by the school's Office of Residence Life, psychologically to…

  4. Manual for School Building Commissions of the State of Delaware.

    Science.gov (United States)

    Delaware State Dept. of Public Instruction, Dover.

    This manual contains provisions of Delaware state law and recommended procedures for construction programs. Areas discussed include--(1) financing, (2) school construction formulae for space allowances, (3) proposed school building budget, (4) procedures for school building construction, (5) a check list for an accounting system, (6) purchase…

  5. Second Summative Report of the Delaware PLATO Project.

    Science.gov (United States)

    Hofstetter, Fred T.

    Begun on an experimental basis in March 1975, the ongoing PLATO project at the University of Delaware has become an established part of the University's academic program. This descriptive report is divided into three sections: (1) project history and development, including organization, utilization, instructor and author training, and projections…

  6. Third Summative Report of the Delaware PLATO Project.

    Science.gov (United States)

    Hofstetter, Fred T.

    Descriptions of new developments in the areas of facilities, applications, user services, support staff, research, evaluation, and courseware production since the Second Summative Report (1977) are provided, as well as a summative overview of PLATO applications at the University of Delaware. Through the purchase of its own PLATO system, this…

  7. Steerable shaft drilling

    Energy Technology Data Exchange (ETDEWEB)

    Pigott, C.P. (Pigott Shaft Drilling Ltd., Preston (UK))

    1990-03-01

    The paper outlines the techniques of steerable shaft drilling and gives brief details of the various machines currently available to carry out this task. It summarizes the many potential benefits of using this method, which could lead to more mines having multiple shafts, each serving a specific purpose. 8 figs.

  8. National Dam Safety Program. Roxbury Dam (Inventory Number 788) Delaware River Basin, Delaware County, New York. Phase I Inspection Report,

    Science.gov (United States)

    1980-05-21

    evaluated and remedied.- t 103 n | mTIOU @9 INOV 5 ,SSoL~eTE. UNCLASSIFIMI SECURITY CLASIFICATION OF T"IS PAGE (When Dete ntered...overturning with seismic considerations included was 2.06 and against sliding was 1.57. Due to the lack of information concerning the embankment materials ...ow____/___R_ Constructed By Owner Cccl-p. 2) Embankment a. Characteristics (1) Embankment Material E ARTN (2) Cutoff Type Pubol. WALL CUTOFF (3

  9. FY 79 Lava Lake Drilling Program: results of drilling experiments

    Energy Technology Data Exchange (ETDEWEB)

    Neel, R.R.; Striker, R.P.; Curlee, R.M.

    1979-12-01

    A drilling program was conducted in December 1978 and January and February 1979 to continue the characterization of the solid and liquid rock components of the Kilauea Iki lava lake. Six holes were drilled from the surface and two previously drilled holes were reentered and deepened for the purposes of measuring downhole temperature profiles, recovering samples of solid, plastic, and molten rock, measuring crust permeability, and determining the performance of conventional and special drilling techniques. Conventional HQ-size (3.78 inches diameter) core drilling equipment using water for cooling and cuttings removal was used to successfully drill during initial entry into 1052/sup 0/C formations. Conventional drilling in reentering flow-back rock was less reliable. The specially designed water jet-augmented drag bit or water jet-augmented core bit was needed to drill reliably into the plastic flow-back rock and through liquid rock veins. This document contains the drill performance data which were recorded during drilling in the crust and the plastic and molten rock zones using both conventional and special drilling procedures and equipment.

  10. Method of drilling with magnetorheological fluid

    NARCIS (Netherlands)

    Zitha, P.L.J.

    2003-01-01

    A method of drilling a bore hole into a stratum, wherein via the drill hole drilling fluid is introduced and fed to the drill head. In order to avoid dilution or leak-off of the drilling fluid the same is in accordance with the invention a magnetorheological drilling fluid, and when an undesirable p

  11. Drilling subsurface wellbores with cutting structures

    Science.gov (United States)

    Mansure, Arthur James; Guimerans, Rosalvina Ramona

    2010-11-30

    A system for forming a wellbore includes a drill tubular. A drill bit is coupled to the drill tubular. One or more cutting structures are coupled to the drill tubular above the drill bit. The cutting structures remove at least a portion of formation that extends into the wellbore formed by the drill bit.

  12. Drilling techniques for osteochondritis dissecans.

    Science.gov (United States)

    Heyworth, Benton E; Edmonds, Eric W; Murnaghan, M Lucas; Kocher, Mininder S

    2014-04-01

    Although the advanced stages of osteochondritis dissecans remain challenging to treat, most early-stage lesions in skeletally immature patients, if managed appropriately, can be stimulated to heal. For stable lesions that do not demonstrate adequate healing with nonoperative measures, such as activity modification, weight-bearing protection, or bracing, drilling of the subchondral bone has emerged as the gold standard of management. Several techniques of drilling exist, including transarticular drilling, retroarticular drilling, and notch drilling. Although each technique has been shown to be effective in small retrospective studies, higher-powered prospective comparative studies are needed to better elucidate their relative advantages and disadvantages.

  13. Impacts on seafloor geology of drilling disturbance in shallow waters.

    Science.gov (United States)

    Corrêa, Iran C S; Toldo, Elírio E; Toledo, Felipe A L

    2010-08-01

    This paper describes the effects of drilling disturbance on the seafloor of the upper continental slope of the Campos Basin, Brazil, as a result of the project Environmental Monitoring of Offshore Drilling for Petroleum Exploration--MAPEM. Field sampling was carried out surrounding wells, operated by the company PETROBRAS, to compare sediment properties of the seafloor, including grain-size distribution, total organic carbon, and clay mineral composition, prior to drilling with samples obtained 3 and 22 months after drilling. The sampling grid used had 74 stations, 68 of which were located along 7 radials from the well up to a distance of 500 m. The other 6 stations were used as reference, and were located 2,500 m from the well. The results show no significant sedimentological variation in the area affected by drilling activity. The observed sedimentological changes include a fining of grain size, increase in total organic carbon, an increase in gibbsite, illite, and smectite, and a decrease in kaolinite after drilling took place.

  14. Steerable percussion air drilling system

    Energy Technology Data Exchange (ETDEWEB)

    Bui, H.D.; Meyers, J.A.; Yost, A.B. II

    1998-12-31

    By increasing penetration rates and bit life, especially in hard formations, the use of down-hole air hammers in the oil field has significantly reduced drilling costs in the Northeast US and West Texas. Unfortunately, drilling by this percussion method has been limited mostly to straight hole applications. This paper presents a new concept of a percussion drilling tool which performs both the function of a down-hole hammer as well as that of a down-hole motor. Such a drilling tool, being introduced here as Steerable Percussion Air Drilling System (SPADS), eliminates the necessity to rotate the drill string and, consequently, enables the use of down-hole air hammers to drill directional wells.

  15. Drilling the Thuringian Syncline, Germany: core processing during the INFLUINS scientific deep drilling campaign

    Science.gov (United States)

    Abratis, Michael; Methe, Pascal; Aehnelt, Michaela; Kunkel, Cindy; Beyer, Daniel; Kukowski, Nina; Totsche, Kai Uwe

    2014-05-01

    Deep drilling of the central Thuringian Syncline was carried out in order to gather substantial knowledge of subsurface fluid dynamics and fluid rock interaction within a sedimentary basin. The final depth of the borehole was successfully reached at 1179 m, just a few meters above the Buntsandstein - Zechstein boundary. One of the aspects of the scientific drilling was obtaining sample material from different stratigraphic units for insights in genesis, rock properties and fluid-rock interactions. Parts of the section were cored whereas cuttings provide record of the remaining units. Coring was conducted in aquifers and their surrounding aquitards, i.e. parts of the Upper Muschelkalk (Trochitenkalk), the Middle Muschelkalk, the Upper Buntsandstein (Pelitrot and Salinarrot) and the Middle Buntsandstein. In advance and in cooperation with the GFZ Potsdam team "Scientific Drilling" core handling was discussed and a workflow was developed to ensure efficient and appropriate processing of the valuable core material and related data. Core curation including cleaning, fitting, marking, measuring, cutting, boxing, photographing and unrolled scanning using a DMT core scanner was carried out on the drilling site in Erfurt. Due care was exercised on samples for microbiological analyses. These delicate samples were immediately cut when leaving the core tube and stored within a cooling box at -78°C. Special software for data input was used developed by smartcube GmbH. Advantages of this drilling information system (DIS) are the compatibility with formats of international drilling projects from the IODP and ICDP drilling programs and thus options for exchanges with the international data bases. In a following step, the drill cores were brought to the national core repository of the BGR in Berlin Spandau where the cores were logged for their physical rock properties using a GeoTek multi sensor core logger (MSCL). After splitting the cores into a working and archive half, the

  16. High Temperature Piezoelectric Drill

    Science.gov (United States)

    Bao, Xiaoqi; Bar-Cohen, Yoseph; Sherrit, Stewart; Badescu, Mircea; Shrout, Tom

    2012-01-01

    Venus is one of the planets in the solar systems that are considered for potential future exploration missions. It has extreme environment where the average temperature is 460 deg C and its ambient pressure is about 90 atm. Since the existing actuation technology cannot maintain functionality under the harsh conditions of Venus, it is a challenge to perform sampling and other tasks that require the use of moving parts. Specifically, the currently available electromagnetic actuators are limited in their ability to produce sufficiently high stroke, torque, or force. In contrast, advances in developing electro-mechanical materials (such as piezoelectric and electrostrictive) have enabled potential actuation capabilities that can be used to support such missions. Taking advantage of these materials, we developed a piezoelectric actuated drill that operates at the temperature range up to 500 deg C and the mechanism is based on the Ultrasonic/Sonic Drill/Corer (USDC) configuration. The detailed results of our study are presented in this paper

  17. Offset drilling obligations

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, K.D.; Kalmakoff, J.J. [Kanuka Thuringer, Regina, SK (Canada)

    1998-12-31

    A review of the `offset well` clause found in freehold and Crown natural gas and petroleum leases was presented. The objective was to provide lessors and lessees with a clear understanding of the rights and obligations associated with offset wells. It was noted that offset well obligations vary according to the form of lease used, the type of offsetting well, the regulatory regime and the geophysical characteristics of the producing formation. Some suggestions were made as to how current versions of the offset well clause can be amended to overcome some of the problems encountered in applying the clause to an offset horizontal well that has been drilled on adjoining lands. Failure to resolve the new issues presented by horizontal drilling technology in terms of documentation, which records respective rights and obligations on the basis of generally accepted principles, will result in large numbers of conflicts and unnecessary litigation. 144 refs., 1 fig.

  18. Successor Characteristics of the Mesozoic and Cenozoic Songliao Basins

    Institute of Scientific and Technical Information of China (English)

    LI Zhongquan; Timothy KUSKY; YING Danlin; GUO Xiaoyu; LI Hongkui

    2008-01-01

    The Songliao basin is a complex successor basin that was initiated in the Mesozoic and experienced multiple periods of reactivation. Based on seismic and drilling data, as well as regional geologic research, we suggest that the Songliao basin contains several different successor basins resting on top of Carboniferous-Permian folded strata forming the basement to the Songliao basin. These basins include the Triassic-Mid Jurassic Paleo-foreland basin, the Late Jurassic-Early Cretaceous downfaulted basin, and an early Cretaceous depressed basin (since the Denglouku Group). This paper presents a systematic study of the basin-mountain interactions, and reveals that there are different types of prototype basin at different geologic times. These prototype basins sequentially superimposed and formed the large Songliao basin. Discovery of the Triassic-early Middle Jurassic paleo-foreland basin fills a Triassic-early Middle Jurassic gap in the geologic history of the Songliao basin. The paleoforeland basin, downfaulted basin, and depressed thermal subsidence basin all together represent the whole Mesozoic-Cenozoic geologic history and deformation of the Songliao basin. Discovery of the Triassic-early Middle Jurassic paleo-foreland basin plays an important role both for deep natural gas exploration and the study of basin-mountain coupling in north China and eastern China in general. This example gives dramatic evidence that we should give much more attention to the polyphase tectonic evolution of related basins for the next phase of exploration and study.

  19. Telescopic drilling rod

    Energy Technology Data Exchange (ETDEWEB)

    Kagan, I.L.; Berezov, S.I.; Gavrilov, G.A.; Goykhman, Ya.A.; Makushkin, D.O.; Rachev, M.P.; Voynich, L.K.

    1981-09-07

    The telescopic drilling rod includes an inner section of the rod, in whose center cable has been passed and is attached a bearing assembly connecting it to the winch, outer section of rod along which there is pipeline connecting the working cavity formed by the inner section of rod and the housing, installed on the lower end of the outer section of rod, with cavity formed by framework of the guide swivel and end piece and connected to the hydraulic system of the machine by pipeline, as well as clamping elements. In order to drill wells to a depth greater than the length of the outer sectrion of the rod, the latter jointly with the inner section of rod is lowered into the extreme lower position until swivel rests on the feed mechanism. With further slipping of cable and the absence of pressure in the hydraulic system, clamping elements do not have an effect on the inner section of rod. It has the opportunity to freely move along the outer section of rod downwards to the face. When pressure is supplied on pipeline into cavity and further through pipeline into working cavity, the inner section of rod is clamped with feed of the outer section in the process of drilling, both sections move jointly. Because of the link between working cavity of sleeve installed on the lower end of the outer section of rod, and the hydraulic system of the machine through the swivel cavity, it is possible to fix the drilling rod in any mutual axial position of the section.

  20. High Temperature Piezoelectric Drill

    Science.gov (United States)

    Bao, Xiaoqi; Scott, James; Boudreau, Kate; Bar-Cohen, Yoseph; Sherrit, Stewart; Badescu, Mircea; Shrout, Tom; Zhang, Shujun

    2009-01-01

    The current NASA Decadal mission planning effort has identified Venus as a significant scientific target for a surface in-situ sampling/analyzing mission. The Venus environment represents several extremes including high temperature (460 deg C), high pressure (9 MPa), and potentially corrosive (condensed sulfuric acid droplets that adhere to surfaces during entry) environments. This technology challenge requires new rock sampling tools for these extreme conditions. Piezoelectric materials can potentially operate over a wide temperature range. Single crystals, like LiNbO3, have a Curie temperature that is higher than 1000 deg C and the piezoelectric ceramics Bismuth Titanate higher than 600 deg C. A study of the feasibility of producing piezoelectric drills that can operate in the temperature range up to 500 deg C was conducted. The study includes the high temperature properties investigations of engineering materials and piezoelectric ceramics with different formulas and doping. The drilling performances of a prototype Ultrasonic/Sonic Drill/Corer (USDC) using high temperate piezoelectric ceramics and single crystal were tested at temperature up to 500 deg C. The detailed results of our study and a discussion of the future work on performance improvements are presented in this paper.

  1. 1985-1995 - 10 years of geothermal drilling in Austria; 1985-1995 - 10 Jahre Geothermiebohrungen in Oesterreich

    Energy Technology Data Exchange (ETDEWEB)

    Goldbrunner, J.

    1997-12-01

    From 1985 to 1995 19 deep drillings with a cumulative length of more than 35 were sunk in Austria for thermal water for energetic or balneological use. Most of the drillings took place in the Styrian Basin and the Upper Austrian Molasse basin, which are the most favourable reas for the exploitation of geothermal energy. (orig.) [Deutsch] Der Zeitraum 1985-1995 war in Oesterreich durch eine intensive Tiefbohrtaetigkeit zur Erschliessung thermaler Tiefengrundwaesser gekennzeichntet. Insgesamt wurden 35.180 Bohrmeter niedergebracht. (orig.)

  2. Polymer Drilling Fluid with Micron-Grade Cenosphere for Deep Coal Seam

    Directory of Open Access Journals (Sweden)

    Peng Xu

    2015-01-01

    Full Text Available Traditional shallow coal seam uses clean water, solid-free system, and foam system as drilling fluid, while they are not suitable for deep coal seam drilling due to mismatching density, insufficient bearing capacity, and poor reservoir protection effect. According to the existing problems of drilling fluid, micron-grade cenosphere with high bearing capacity and ultralow true density is selected as density regulator; it, together with polymer “XC + CMC” and some other auxiliary agents, is jointly used to build micron-grade polymer drilling fluid with cenosphere which is suitable for deep coal seam. Basic performance test shows that the drilling fluid has good rheological property, low filtration loss, good density adjustability, shear thinning, and thixotropy; besides, drilling fluid flow is in line with the power law rheological model. Compared with traditional drilling fluid, dispersion stability basically does not change within 26 h; settlement stability evaluated with two methods only shows a small amount of change; permeability recovery rate evaluated with Qinshui Basin deep coal seam core exceeds 80%. Polymer drilling fluid with cenosphere provides a new thought to solve the problem of drilling fluid density and pressure for deep coal seam drilling and also effectively improves the performance of reservoir protection ability.

  3. Exploration potential of offshore northern California basins

    Energy Technology Data Exchange (ETDEWEB)

    Bachman, S.B.; Crouch, J.K.

    1988-01-01

    A series of exploratory wells was drilled in the northern California offshore basins in the 1960s following leasing of federal tracts off northern California, Oregon, and Washington. The drilling, although encountering numerous oil shows, was considered at the time to indicate low prospectivity in an area that extended as far south as the offshore Santa Maria basin. However, subsequent major discoveries in this decade in the offshore Santa Maria basin, such as the Point Arguello field, indicate that these offshore basins may be highly prospective exploration targets. Many of the key features of Monterey production in central and southern California are also present in the offshore basins of northern California. A new 5-year leasing plan has scheduled leasing in the northern California OCS starting in early 1989. The first basins on the schedule, the Point Arena and Eel River basins, differ in some respects. The Point Arena basin is more typical of a Monterey basin, with the potential for fractured chert reservoirs and organic-rich sections, deep burial of basinal sections to enhance the generation of higher gravity oils, and complex folding and faulting. The Eel River basin is more clastic-rich in its gas-producing, onshore extension. Key questions in the Eel River basin include whether the offshore, more distal stratigraphy will include Monterey-like biogenic sediments, and whether the basin has oil potential in addition to its proven gas potential. The Outer Santa Cruz basin shares a similar stratigraphy, structure, and hydrocarbon potential with the Point Arena basin. The Santa Cruz-Bodega basin, also with a similar stratigraphy, may have less exploration potential because erosion has thinned the Monterey section in parts of the basin.

  4. The Lake El’gygytgyn Scientific Drilling Project – Conquering Arctic Challenges through Continental Drilling

    Directory of Open Access Journals (Sweden)

    Georg Schwamborn

    2011-03-01

    Full Text Available Between October 2008 and May 2009, the International Continental Scientific Drilling Program (ICDPco-sponsored a campaign at Lake El´gygytgyn, located in a 3.6-Ma-old meteorite impact crater in northeastern Siberia. Drilling targets included three holes in the center of the 170-m-deep lake, utilizing the lake ice cover as a drilling platform, plus one hole close to the shore in the western lake catchment. At the lake’s center. the entire 315-m-thick lakesediment succession was penetrated. The sediments lack any hiatuses (i.e., no evidence of basin glaciation or desiccation, and their composition reflects the regional climatic and environmental history with great sensitivity. Hence, the record provides the first comprehensive and widely timecontinuous insights into the evolution of the terrestrial Arctic since mid-Pliocene times. This is particularly true for the lowermost 40 meters and uppermost 150 meters of the sequence, which were drilled with almost 100% recovery and likely reflect the initial lake stage during the Pliocene and the last ~2.9 Ma, respectively. Nearly 200 meters of underlying rock were also recovered; these cores consist of an almost complete section of the various types of impact breccias including broken and fractured volcanic basement rocks and associated melt clasts. The investigation of this core sequence promises new information concerning the El´gygytgyn impact event, including the composition and nature of the meteorite, the energy released, and the shock behavior of the volcanic basement rocks. Complementary information on the regional environmental history, including the permafrost history and lake-level fluctuations, is being developed from a 142-m-long drill core recovered from the permafrost deposits in the lake catchment. This core consists of gravelly and sandy alluvial fan deposits in ice-rich permafrost, presumably comprising a discontinuous recordof both Quaternary and Pliocene deposits.

  5. Importance of drill string assembly swivel in horizontal drilling

    Directory of Open Access Journals (Sweden)

    Edmund Tasak

    2006-10-01

    Full Text Available A part of the drill string – the swivel (rotational connector – accomplishes an important task in the horizontal drilling. Its malfunctioning makes it impossible to draw in ( install large diameter and length pipelines. The causes of the connector break-down during the horizontal drilling are investigated in the paper. The drilling has been made for twenty inches gas pipeline installation during reaming operations. A trouble was encountered making good work conditions of a system consisting of the drilling machine drill string reamer swivel tube shield of Cardan joint and the gas pipeline 500 m long. In this case, the swivel brokes down and the planned operation was not finished. The assessment of improper drilling conditions, selection of operation system components, and drilling parameters and the insufficient technological supervising have created an excessive risk of failure. A proper application of technical analysis would considerably decrease the hazard of failure which cause large costs, delays and decrease of confidence to the drilling contractor and pipeline installation.

  6. LAND STREAMER SEISMIC DATA FROM NORTHERN DELAWARE: A VIABLE ALTERNATIVE FOR IMAGING AQUIFERS IN SUBURBAN AREAS

    Science.gov (United States)

    Velez, C. C.; McLaughlin, P. P.; McGeary, S. E.; Sargent, S. L.

    2009-12-01

    The Potomac Formation includes the most important confined aquifers in the Coastal Plain of northern Delaware. Development and a growing suburban population are increasing demand for groundwater in the area, making accurate assessment of groundwater water supply increasingly important. Previous studies of subsurface geology indicate that the Potomac Formation is characterized by laterally discontinuous fluvial sand bodies, making it difficult to precisely delineate the distribution and geometry of the aquifer facies based on well correlations alone. A 20-km high-resolution seismic reflection dataset was collected using a land-streamer system in 2008 to constrain subsurface stratigraphy between disparate well locations. The data were collected along roadways in an area of mixed development that includes suburban housing tracts, farmlands, and large industry. A 152-m-deep continuous-cored test hole was drilled in the summer of 2009 adjacent to one of the lines and a full suite of borehole geophysical logs obtained. The land-streamer data are compared to a 3-km dataset collected also in 2008 using conventional methods on farmland in the northern part of the study area. The land streamer system proved to be more effective than conventional seismic reflection methods in this area. Several advantages are evident for the land streamer: 1) overall, the conventional dataset has a higher S/N, 2) on average, collecting data with the land streamer system is four times faster, and 3) the land streamer lines can be longer and therefore more continuous than the conventional lines in a developed area. The land-streamer system has minor disadvantages: traffic control, traffic noise, and in some cases a need for larger crews. Regardless, the land streamer dataset is easier to process, of higher quality, and more cost effective. The final depth images from the land streamer data indicate that the minimum and maximum depths imaged are ~18 m and ~ 268m, with a resolution of ~4 m. This

  7. Sand, salt and water in the Stampriet Basin, Namibia: Calculating ...

    African Journals Online (AJOL)

    is the first time that substantial direct (diffuse) recharge has been quantified for the Stampriet Basin, and this part ... large-scale drilling at these sites, and borehole level monitoring ..... using a laser granulometer with statistics calculated using.

  8. Drilling successful from ROV Ventana

    Science.gov (United States)

    Stakes, Debra S.; McFarlane, James A. R.; Holloway, G. Leon; Greene, H. Gary

    Cores of granite and deformed sediment from the walls of Monterey Canyon were successfully recovered from December 30 to 31, 1992, by Monterey Bay Aquarium Research Institute's (MBARI) Remotely Operated Vehicle (ROV) Ventana using a small-diameter, double-barrel drill with a diamond bit. This HSTR (Holloway-Stakes-Tengdin-Rajcula) drill was developed to drill cores horizontally from sulfide/sulfate walls of active black smokers. The drill was first successfully used by the submersible Alvin in October 1991 to drill into massive sulfide chimneys, on the Juan de Fuca Ridge (Eos, June 30, 1992, p. 273), and it was subsequently used with equal success on the chalcopyrite-rich chimneys from 21°N and 9°N on the East Pacific Rise. The recent December dives, however, marked the first time that drilling has ever been attempted from the smaller ROV and the first time coring into the harder igneous rock substrate has been attempted.

  9. Exploration Drilling and Technology Demonstration At Fort Bliss

    Energy Technology Data Exchange (ETDEWEB)

    Barker, Ben; Moore, Joe [EGI; Segall, Marylin; Nash, Greg; Simmons, Stuart; Jones, Clay; Lear, Jon; Bennett, Carlon

    2014-02-26

    The Tularosa-Hueco basin in south-central New Mexico has long been known as an extensional area of high heat flow. Much of the basin is within the Fort Bliss military reservation, which is an exceptionally high value customer for power independent of the regional electric grid and for direct use energy in building climate control. A series of slim holes drilled in the 1990s established the existence of a thermal anomaly but not its practical value. This study began in 2009 with a demonstration of new exploration drilling technology. The subsequent phases reported here delivered a useful well, comparative exploration data sets and encouragement for further development. A production-size well, RMI56-5, was sited after extensive study of archival and newly collected data in 2010-2011. Most of 2012 was taken up with getting state and Federal authorities to agree on a lead agency for permitting purposes, getting a drilling permit and redesigning the drilling program to suit available equipment. In 2013 we drilled, logged and tested a 924 m well on the McGregor Range at Fort Bliss using a reverse circulation rig. Rig tests demonstrated commercial permeability and the well has a 7-inch slotted liner for use either in production or injection. An August 2013 survey of the completed well showed a temperature of 90 C with no reversal, the highest such temperature in the vicinity. The well’s proximity to demand suggests a potentially valuable resource for direct use heat and emergency power generation. The drilling produced cuttings of excellent size and quality. These were subjected to traditional analyses (thin sections, XRD) and to the QEMScan™ for comparison. QEMScan™ technology includes algorithms for determining such properties of rocks as density, mineralogy, heavy/light atoms, and porosity to be compared with direct measurements of the cuttings. In addition to a complete cuttings set, conventional and resistivity image logs were obtained in the open hole before

  10. Exploration Drilling and Technology Demonstration At Fort Bliss

    Energy Technology Data Exchange (ETDEWEB)

    Barker, Ben; Moore, Joe [EGI; Segall, Marylin; Nash, Greg; Simmons, Stuart; Jones, Clay; Lear, Jon; Bennett, Carlon

    2014-02-26

    The Tularosa-Hueco basin in south-central New Mexico has long been known as an extensional area of high heat flow. Much of the basin is within the Fort Bliss military reservation, which is an exceptionally high value customer for power independent of the regional electric grid and for direct use energy in building climate control. A series of slim holes drilled in the 1990s established the existence of a thermal anomaly but not its practical value. This study began in 2009 with a demonstration of new exploration drilling technology. The subsequent phases reported here delivered a useful well, comparative exploration data sets and encouragement for further development. A production-size well, RMI56-5, was sited after extensive study of archival and newly collected data in 2010-2011. Most of 2012 was taken up with getting state and Federal authorities to agree on a lead agency for permitting purposes, getting a drilling permit and redesigning the drilling program to suit available equipment. In 2013 we drilled, logged and tested a 924 m well on the McGregor Range at Fort Bliss using a reverse circulation rig. Rig tests demonstrated commercial permeability and the well has a 7-inch slotted liner for use either in production or injection. An August 2013 survey of the completed well showed a temperature of 90 C with no reversal, the highest such temperature in the vicinity. The well’s proximity to demand suggests a potentially valuable resource for direct use heat and emergency power generation. The drilling produced cuttings of excellent size and quality. These were subjected to traditional analyses (thin sections, XRD) and to the QEMScan™ for comparison. QEMScan™ technology includes algorithms for determining such properties of rocks as density, mineralogy, heavy/light atoms, and porosity to be compared with direct measurements of the cuttings. In addition to a complete cuttings set, conventional and resistivity image logs were obtained in the open hole before

  11. Streamflow and water-quality monitoring in response to young-of-year smallmouth bass (micropterus dolomieu) mortality in the Susquehanna River and major tributaries, with comparisons to the Delaware and Allegheny Rivers, Pennsylvania, 2008-10

    Science.gov (United States)

    Chaplin, Jeffrey J.; Crawford, J. Kent

    2012-01-01

    Since 2005, spring hatched young-of-year (YOY) smallmouth bass in Pennsylvania reaches of the Susquehanna River have experienced above-normal mortality when summertime streamflows are near or lower than normal. Stress factors include, but are not limited to, low dissolved oxygen and elevated water temperatures during times critical for survival and development (critical period is May 1 through July 31). At this time (2010), widespread disease and mortality are believed to be more prevalent for YOY smallmouth bass in the Susquehanna River Basin than in the Delaware or Allegheny River Basins.

  12. An innovative drilling system

    Energy Technology Data Exchange (ETDEWEB)

    Nees, J.; Dickinson, E.; Dickinson, W.; Dykstra, H.

    1991-05-01

    The principal project objectives were the following: To demonstrate the capability of the Ultrashort Radius Radial System to drill and complete multiple horizontal radials in a heavy oil formation which had a production history of thermal operations. To study the effects that horizontal radials have on steam placement at specific elevations and on reducing gravity override. To demonstrate that horizontal radials could be utilized for cyclic production, i.e. for purposes of oil production as well as for steam injection. Each of these objectives was successfully achieved in the project. Early production results indicate that radials positively influenced cyclic performance. This report documents those results. 15 refs., 29 figs., 1 tab.

  13. The Hominin Sites and Paleolakes Drilling Project (HSPDP): Understanding the paleoenvironmental and paleoclimatic context of human origins through continental drilling

    Science.gov (United States)

    Cohen, Andrew S.; Campisano, Christopher; Asrat, Asfawossen; Arrowsmith, Ramon; Deino, Alan; Feibel, Craig; Hill, Andrew; Kingston, John; Lamb, Henry; Lowenstein, Tim; Olago, Daniel; Bernhart Owen, R.; Renaut, Robin; Schabitz, Frank; Trauth, Martin

    2015-04-01

    The influence of climate and environmental history on human evolution is an existential question that continues to be hotly debated, in part because of the paucity of high resolution records collected in close proximity to the key fossil and archaeological evidence. To address this issue and transform the scientific debate, the HSPDP was developed to collect lacustrine sediment drill cores from basins in Kenya and Ethiopia that collectively encompass critical time intervals and locations for Plio-Quaternary human evolution in East Africa. After a 17 month campaign, drilling was completed in November, 2014, with over 1750m of core collected from 11 boreholes from five areas (1930m total drilling length, avg. 91% recovery). The sites, from oldest to youngest, include 1) N. Awash, Ethiopia (~3.5-2.9Ma core interval); 2) Baringo-Tugen Hills, Kenya (~3.3-2.5Ma); 3) West Turkana, Kenya (~1.9-1.4Ma); L. Magadi, Kenya (0.8-0Ma) and the Chew Bahir Basin, Ethiopia (~0.5-0Ma). Initial core description (ICD) and sampling for geochronology, geochemistry and paleoecology studies had been completed by mid2014, with the two remaining sites (Magadi and Chew Bahir) scheduled for ICD work in early 2015. Whereas the primary scientific targets were the lacustrine deposits from the hominin-bearing basin depocenters, many intervals of paleosols (representative of low lake stands and probable arid periods) were also encountered in drill cores. Preliminary analyses of drill core sedimentology and geochemistry show both long-term lake level changes and cyclic variability in lake levels, both of which may be indicative of climatic forcing events of interest to paleoanthropologists. Authors of this abstract also include the entire HSPDP field team.

  14. Independent focuses Philippines exploration on Visayan basin

    Energy Technology Data Exchange (ETDEWEB)

    Rillera, F.G. [Cophil Exploration Corp., Manila (Philippines)

    1995-08-21

    Cophil Exploration Corp., a Filipino public company, spearheaded 1995 Philippine oil and gas exploration activity with the start of its gas delineation drilling operations in Libertad, northern Cebu. Cophil and its Australian partners, Coplex Resources NL and PacRim Energy NL, have set out to complete a seven well onshore drilling program within this block this year. The companies are testing two modest shallow gas plays, Libertad and Dalingding, and a small oil play, Maya, all in northern Cebu about 500 km southeast of Manila. Following a short discussion on the geology and exploration history of the Visayan basin, this article briefly summarizes Cophil`s ongoing Cebu onshore drilling program. Afterwards, discussion focuses on identified exploration opportunities in the basin`s offshore sector.

  15. 30 CFR 33.34 - Drilling test.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drilling test. 33.34 Section 33.34 Mineral... MINING PRODUCTS DUST COLLECTORS FOR USE IN CONNECTION WITH ROCK DRILLING IN COAL MINES Test Requirements § 33.34 Drilling test. (a) A drilling test shall consist of drilling a set of 10 test holes,...

  16. Recent R&D in Drilling Equipment

    Institute of Scientific and Technical Information of China (English)

    Sun Zuchen; Huang Zhiqian

    1997-01-01

    @@ Situation for Drilling Equipment Technical performance of drilling equipment and perfection of supporting systems hold the key to drilling safety, technical procedure development and drilling cost. In the end of the 1980s, the stituation for drilling equipment was not optimistic in China because of poor technical performance, low-level supporting system and scarcity of electric-driven rigs.

  17. Experiments in water spreading at Newark, Delaware

    Science.gov (United States)

    Boggess, Durward Haye; Rima, Donald Robert

    1962-01-01

    Two experiments in water spreading were made at Newark, Del., to evaluate the prospects of using excess storm runoff to recharge the shallow water-table aquifer which serves the community. Water was diverted from 1 of the city's 3 production wells and released into an infiltration ditch near the municipal well field. Although slightly more than 65,000 cubic feet of water (nearly 500,000 gallons ) was spread in the infiltration ditch and allowed to seep into the subsurface, there was no indication that any appreciable amount of water reached the producing aquifer. Instead, a perched zone of saturation was created by the presence of an impermeable or slightly permeable bed above the water table. So effective is this barrier to the downward movement of water that within a period of less than 1 day, the apex of the perched zone rose about 10 feet to the level of the bottom of the infiltration ditch. As more water was added, the mound of saturation spread laterally. On the basis of these experiments, it appears that the principal aquifer at Newark, Del., would not be benefited by spreading water in shallow infiltration ditches or basins. However, the absorptive capacity of the unsaturated materials which occur at a shallow depth, is sufficient to permit the disposal of large volumes of storm runoff.

  18. 78 FR 22840 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; State Board Requirements

    Science.gov (United States)

    2013-04-17

    ... requirements of the Clean Air Act (CAA) for all criteria pollutants of the national ambient air quality... Promulgation of Air Quality Implementation Plans; Delaware; State Board Requirements,'' that is located in the... AGENCY 40 CFR Part 52 Approval and Promulgation of Air Quality Implementation Plans; Delaware; State...

  19. The Delaware Geography-Health Initiative: Lessons Learned in Designing a GIS-Based Curriculum

    Science.gov (United States)

    Rees, Peter W.; Silberman, Jordan A.

    2010-01-01

    The Delaware Geography-Health Initiative is a Web- and GIS-based set of lesson units for teaching geographic concepts and research methods within the context of the state's high school geography standards. Each unit follows a research-based, inquiry-centered model addressing questions of health because of Delaware's high incidence of cancer,…

  20. 33 CFR 100.T05-0443 - Safety Zone; Fireworks Display, Delaware River, New Hope, PA.

    Science.gov (United States)

    2010-07-01

    ..., Delaware River, New Hope, PA. 100.T05-0443 Section 100.T05-0443 Navigation and Navigable Waters COAST GUARD... Safety Zone; Fireworks Display, Delaware River, New Hope, PA. (a) Location. The safety zone will restrict.... Bridge located in New Hope, PA, and 400 ft east of the shoreline of New Hope, PA. (b) Regulations. (1)...

  1. 75 FR 33690 - Safety Zone, Lights on the River Fireworks Display, Delaware River, New Hope, PA

    Science.gov (United States)

    2010-06-15

    ..., Delaware River, New Hope, PA AGENCY: Coast Guard, DHS. ACTION: Temporary final rule. SUMMARY: The Coast Guard is establishing a temporary safety zone on the Delaware River in New Hope, PA. The safety zone... downriver of the bridge in New Hope, PA. DATES: This rule is effective from June 15, 2010 through July...

  2. 33 CFR 334.120 - Delaware Bay off Milford Neck; naval aircraft bombing target area.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Delaware Bay off Milford Neck; naval aircraft bombing target area. 334.120 Section 334.120 Navigation and Navigable Waters CORPS OF....120 Delaware Bay off Milford Neck; naval aircraft bombing target area. (a) The danger zone. A circular...

  3. 33 CFR 167.173 - Off Delaware Bay: Two-Way Traffic Route.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Off Delaware Bay: Two-Way Traffic... SECURITY (CONTINUED) PORTS AND WATERWAYS SAFETY OFFSHORE TRAFFIC SEPARATION SCHEMES Description of Traffic Separation Schemes and Precautionary Areas Atlantic East Coast § 167.173 Off Delaware Bay: Two-Way Traffic...

  4. The Delaware Geography-Health Initiative: Lessons Learned in Designing a GIS-Based Curriculum

    Science.gov (United States)

    Rees, Peter W.; Silberman, Jordan A.

    2010-01-01

    The Delaware Geography-Health Initiative is a Web- and GIS-based set of lesson units for teaching geographic concepts and research methods within the context of the state's high school geography standards. Each unit follows a research-based, inquiry-centered model addressing questions of health because of Delaware's high incidence of cancer,…

  5. 33 CFR 110.70 - Chesapeake and Delaware Canal, easterly of Courthouse Point, Md.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Chesapeake and Delaware Canal, easterly of Courthouse Point, Md. 110.70 Section 110.70 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.70 Chesapeake and Delaware Canal, easterly of...

  6. Virtual Visit to the ATLAS Control Room by The University of Delaware

    CERN Multimedia

    2013-01-01

    The University of Delaware along with MAGPI (Metropolitan Area GigaPoP in Philadelphia for Internet2) and Internet2 are excited to host "Network Delaware Day: Advancing Research and Education Initiatives Across the First State." Discover the power of advanced networking opportunities in research and education throughout the First State.

  7. Evaluation of Delaware Stars for Early Success: Year 1 Report. Research Report

    Science.gov (United States)

    Schwartz, Heather L.; Karoly, Lynn A.; Le, Vi-Nhuan; Tamargo, Jennifer; Setodji, Claude Messan

    2014-01-01

    Delaware was in the first group of states to receive a federal grant in 2012 to improve early care and education services and increase the number of infants, toddlers, and preschool-age children in high-quality programs. One component of the state's grant is a rigorous validation process for Delaware Stars for Early Success, a voluntary quality…

  8. Literacy at the Core of the Delaware World Language Immersion Programs

    Science.gov (United States)

    Fulton-Archer, Lynn

    2013-01-01

    Certain aspects of the implementation of language immersion programs in Delaware are unique given the state's size, demographics, and role in national education initiatives including Race to the Top, Common Core, and Smarter Balance. The Delaware experience typifies what every state, district, or even school goes through as they try to provide…

  9. 500.000 years of environmental history in Eastern Anatolia: The PALEOVAN drilling project

    DEFF Research Database (Denmark)

    Litt, Thomas; Anselmetti, Flavio; Baumgarten, Henrike

    2012-01-01

    International Continental Scientific Drilling Program (ICDP) drilled a complete succession of the lacustrine sediment sequence deposited during the last ~500,000 years in Lake Van, Eastern Anatolia (Turkey). Based on a detailed seismic site survey, two sites at a water depth of up to 360 m were...... drilled in summer 2010, and cores were retrieved from sub-lake-floor depths of 140 m (Northern Basin) and 220 m (Ahlat Ridge). To obtain a complete sedimentary section, the two sites were multiple-cored in order to investigate the paleoclimate history of a sensitive semi-arid region between the Black...

  10. Great Progress of Drilling Technology in China

    Institute of Scientific and Technical Information of China (English)

    Li Kexiang

    1994-01-01

    @@ A great progress has been made in drilling technology in China from 1986 to 1990 by popularizing research achievements and emphasizing high economic efficiency of exploration and development, high quality of drilling engineering, high drilling rate and formation damage prevention.

  11. Advances in core drilling technology

    Science.gov (United States)

    Holdsworth, G.

    Some notable technical advances in drill design were reported at the meeting, held in Canada August 30-September 1, 1982, at the University of Calgary. Chief amongst these was a battery powered, computer assisted electromechanical core drill which has recently been used by the Danes in Greenland to continuously core to the base of the ice sheet at 2038 m. This is the deepest coring operation so far on the Greenland ice sheet. (The record for deep glacier drilling is held by the U.S. Army Cold Regions Research and Engineering Laboratory for the continuous coring through 2164 m of ice to bedrock at Byrd Station, Antarctica, in 1968). In early 1982, a current Soviet core drilling operation was reported to be at a depth of 2000 m at Vostok station, Antarctica, where the total ice thickness is about 4000 m; the goal of core drilling the entire ice thickness there could be achieved before the end of 1983.

  12. DRILL BITS FOR HORIZONTAL WELLS

    Directory of Open Access Journals (Sweden)

    Paolo Macini

    1996-12-01

    Full Text Available This paper underlines the importance of the correct drill bit application in horizontal wells. Afler the analysis of the peculiarities of horizontal wells and drainholes drilling techniques, advantages and disadvantages of the application of both roller cone and fixed cutters drill bits have been discussed. Also, a review of the potential specific featuries useful for a correct drill bit selection in horizontal small diameter holes has been highlighted. Drill bits for these special applications, whose importance is quickly increasing nowadays, should be characterised by a design capable to deliver a good penetration rate low WOB, and, at the same time, be able to withstand high RPM without premature cutting structure failure and undergauge. Formation properties will also determine the cutting structure type and the eventual specific features for additional gauge and shoulder protection.

  13. The Marskhod Egyptian Drill Project

    Science.gov (United States)

    Shaltout, M. A. M.

    We describe a possible participation of Egypt in a future Mars rover Mission. It was suggested that Egypt participate through involvement in the design, building and testing of a drill to obtain sub-surface samples. The Space Research Institute of the Russian Academy of Sciences (IKI), formally invited the Egyptian Ministry of Scientific Research to study the concept for potential use on the Russian Mars 2001 Mission. As one of the objectives of the Marskhod mission was the analysis of sub-surface samples, a drilling mechanism in the payload would be essential. The Egyptian expertise in drill development is associated with the archaeological exploration of the Pyramids. A sophisticated drilling system perforated limestone to a depth of 2 m without the use of lubricants or cooling fluids that might have contaminated the Pit's environment. This experience could have been applied to a drill development Mars 2001 mission, which was unfortunately canceled due to economic problems.

  14. Automatic evaluation of drilling fluid properties

    OpenAIRE

    Hansen, Eirik

    2012-01-01

    This thesis is structured in two main parts. First part covers the fundamental role of drilling fluid in the drilling process. It provides a description of the mud circulating system for conventional drilling operations, outlines the basic composition of drilling fluids, and describes the main functions and properties of drilling fluids. Furthermore it describes the current testing procedures and equipment and illustrates how testing is used in the evaluation of drilling fluid ...

  15. Dual gradient drilling - simulations during connection operations

    OpenAIRE

    Time, André

    2014-01-01

    As oilfields are ageing and depleting, operators are forced to start searching for oil in more hostile environments. These new environments can introduce new drilling challenges. Prospects like ultra deep water reservoirs and depleted offshore reservoirs are difficult to drill with conventional drilling. This has lead the industry to developing the Dual Gradient Drilling (DGD) system. DGD is an unconventional drilling method and it is classified as a Managed Pressure Drilling ...

  16. Quantification and probabilistic modeling of CRT obsolescence for the State of Delaware

    Energy Technology Data Exchange (ETDEWEB)

    Schumacher, Kelsea A., E-mail: kschum@udel.edu [Center for Energy and Environmental Policy, University of Delaware, 278 Graham Hall, Newark, 19716 (United States); Schumacher, Thomas, E-mail: schumact@udel.edu [Department of Civil and Environmental Engineering, University of Delaware, Newark, 19711 (United States); Agbemabiese, Lawrence, E-mail: agbe@udel.edu [Center for Energy and Environmental Policy, University of Delaware, 272 Graham Hall, Newark, 19716 (United States)

    2014-11-15

    Highlights: • We modeled the obsolescence of cathode ray tube devices in the State of Delaware. • 411,654 CRT units or ∼16,500 metric tons have been recycled in Delaware since 2002. • The peak of the CRT obsolescence in Delaware passed by 2012. • The Delaware average CRT recycling rate between 2002 and 13 was approximately 27.5%. • CRTs will continue to infiltrate the system likely until 2033. - Abstract: The cessation of production and replacement of cathode ray tube (CRT) displays with flat screen displays have resulted in the proliferation of CRTs in the electronic waste (e-waste) recycle stream. However, due to the nature of the technology and presence of hazardous components such as lead, CRTs are the most challenging of electronic components to recycle. In the State of Delaware it is due to this challenge and the resulting expense combined with the large quantities of CRTs in the recycle stream that electronic recyclers now charge to accept Delaware’s e-waste. Therefore it is imperative that the Delaware Solid Waste Authority (DSWA) understand future quantities of CRTs entering the waste stream. This study presents the results of an assessment of CRT obsolescence in the State of Delaware. A prediction model was created utilizing publicized sales data, a variety of lifespan data as well as historic Delaware CRT collection rates. Both a deterministic and a probabilistic approach using Monte Carlo Simulation (MCS) were performed to forecast rates of CRT obsolescence to be anticipated in the State of Delaware. Results indicate that the peak of CRT obsolescence in Delaware has already passed, although CRTs are anticipated to enter the waste stream likely until 2033.

  17. Microgravity Drill and Anchor System

    Science.gov (United States)

    Parness, Aaron; Frost, Matthew A.; King, Jonathan P.

    2013-01-01

    This work is a method to drill into a rock surface regardless of the gravitational field or orientation. The required weight-on-bit (WOB) is supplied by a self-contained anchoring mechanism. The system includes a rotary percussive coring drill, forming a complete sampling instrument usable by robot or human. This method of in situ sample acquisition using micro - spine anchoring technology enables several NASA mission concepts not currently possible with existing technology, including sampling from consolidated rock on asteroids, providing a bolt network for astronauts visiting a near-Earth asteroid, and sampling from the ceilings or vertical walls of lava tubes and cliff faces on Mars. One of the most fundamental parameters of drilling is the WOB; essentially, the load applied to the bit that allows it to cut, creating a reaction force normal to the surface. In every drilling application, there is a minimum WOB that must be maintained for the system to function properly. In microgravity (asteroids and comets), even a small WOB could not be supported conventionally by the weight of the robot or astronaut. An anchoring mechanism would be needed to resist the reactions, or the robot or astronaut would push themselves off the surface and into space. The ability of the system to anchor itself to a surface creates potential applications that reach beyond use in low gravity. The use of these anchoring mechanisms as end effectors on climbing robots has the potential of vastly expanding the scope of what is considered accessible terrain. Further, because the drill is supported by its own anchor rather than by a robotic arm, the workspace is not constrained by the reach of such an arm. Yet, if the drill is on a robotic arm, it has the benefit of not reflecting the forces of drilling back to the arm s joints. Combining the drill with the anchoring feet will create a highly mobile, highly stable, and highly reliable system. The drilling system s anchor uses hundreds of

  18. A stratigraphical-geochemical study on the Chaco Paraná continental rift basin- An approach study based on regional sedimentology and drill-hole core analyses,South América

    Institute of Scientific and Technical Information of China (English)

    Roberto Torra

    2006-01-01

    This paper is focused on a geologic "regional rift basin system pattern" and its stratigraphical-geochemical relationship. This is mainly based on the littoral shallow marine sedimentary succession paleogeography and deposits. These successions characterize the large extensional intracratonic Chaco rift basin system evolved from the Upper Cretaceous ( Late Campanian-Senonian-Maastrichtian-Early Paleocene) to Quaternary time. The siliciclastic littoral shallow marine successions were deposited from Early Senonian-Maastrichtian to Late Miocene during three main successive littoral shallow marine transgressions of continental extension.These transgressions happened over the wide pediplanized terrains of South America. These lands exist west of the more positive areas, between the Brazilian Shield and the foreland massifs that were settled in the more westernwards areas. Later, these regional foreland massifs were coupled and raised to the Andean Orogen Belt during the last 5 million years.The extensive intracratonic pediplanized low topographic relief areas were the reservoirs of siliciclastic littoral shallow marine succession deposits during the three successive widespread vast continental littoral shallow marine transgressions.The first transgression began at the Latest Campanian-Senonian and/or Early Maastrichtian time. After this episode, the sedimentary depositional systems continued during the Cenozoic until the Latest Miocene. These successions constitute a major allostratigraphic unit.The limit with underlying units is the regional unconformity between the regional volcanic event (Jurassic-Cretacic and interleaved eolianite sandstones) at the base and the undifferentiated Quaternary sediments (called as the Pampeano and Post-Pampeano Formations sensu lato). Based on many facies analyses there had been checked out different levels in the eustatic sea level variations within the allostratigraphic unit.Three major stages of extensional climax were recognized and

  19. Drilling miniature holes, Part III

    Energy Technology Data Exchange (ETDEWEB)

    Gillespie, L.K.

    1978-07-01

    Miniature components for precision electromechanical mechanisms such as switches, timers, and actuators typically require a number of small holes. Because of the precision required, the workpiece materials, and the geometry of the parts, most of these holes must be produced by conventional drilling techniques. The use of such techniques is tedious and often requires considerable trial and error to prevent drill breakage, minimize hole mislocation and variations in hole diameter. This study of eight commercial drill designs revealed that printed circuit board drills produced better locational and size repeatability than did other drills when centerdrilling was not used. Boring holes 1 mm in dia, or less, as a general rule did not improve hole location in brass or stainless steel. Hole locations of patterns of 0.66-mm holes can be maintained within 25.4-..mu..m diametral positional tolerance if setup misalignments can be eliminated. Size tolerances of +- 3.8 ..mu..m can be maintained under some conditions when drilling flat plates. While these levels of precision are possible with existing off-the-shelf drills, they may not be practical in many cases.

  20. Establishing nuclear facility drill programs

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The purpose of DOE Handbook, Establishing Nuclear Facility Drill Programs, is to provide DOE contractor organizations with guidance for development or modification of drill programs that both train on and evaluate facility training and procedures dealing with a variety of abnormal and emergency operating situations likely to occur at a facility. The handbook focuses on conducting drills as part of a training and qualification program (typically within a single facility), and is not intended to included responses of personnel beyond the site boundary, e.g. Local or State Emergency Management, Law Enforcement, etc. Each facility is expected to develop its own facility specific scenarios, and should not limit them to equipment failures but should include personnel injuries and other likely events. A well-developed and consistently administered drill program can effectively provide training and evaluation of facility operating personnel in controlling abnormal and emergency operating situations. To ensure the drills are meeting their intended purpose they should have evaluation criteria for evaluating the knowledge and skills of the facility operating personnel. Training and evaluation of staff skills and knowledge such as component and system interrelationship, reasoning and judgment, team interactions, and communications can be accomplished with drills. The appendices to this Handbook contain both models and additional guidance for establishing drill programs at the Department`s nuclear facilities.

  1. Steerable percussion air drilling system

    Energy Technology Data Exchange (ETDEWEB)

    Bui, H.D.; Gray, M.A.; Oliver, M.S.

    1995-07-01

    In the Steerable Percussion Air Drilling System (SPADS), air percussion is used to drill directionally in hard formations. Compared to mud or air powered PDM motors, SPADS offers directional drilling at high penetration rate, reduced mud costs, negligible formation damage, and immediate indication of hole productivity. Field tests turned up problems ranging from tool design to operation procedures; remedies were developed. There is an optimum WOB (weight on bit) at which torque is reasonably low. The hammer was tested at three different line pressures (200, 300, 350 psig) at optimum WOB in granite, limestone, and sandstone.

  2. Exploration Breakthrough in Southern Margin of Junggar Basin

    Institute of Scientific and Technical Information of China (English)

    Kang Zhulin; Zheng Jiandong

    1997-01-01

    @@ The Hutubi structure, located in the southern margin of Junggar Basin, is 60 km norrthwest of Urumqi and 20 km northwest of Changji (Fig. l). The Hu-2 well drilled in the Hutubi structure has gained high-yield gas flow,significant exploration breakthrough in the southern margin of Junggar Basin since the 1950s.

  3. Study on the ocean drilling program

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Jae Ho; Han, Hyun Chul; Chin, Jae Wha; Lee, Sung Rok; Park, Kwan Soon; Lee, Young Joo; Park, Young Soo [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1996-12-01

    Geoscience research trend of the world nations is focusing on the study of climate changes and preventing people from the natural hazards such as earthquakes and volcanic activities. For this study, it is necessary for scientists to interpret ancient climate changes preserved in ocean sediments, and to observe plate motions. Thus, geological and geophysical studies should be proceeded for the core samples recovered from the deep sea sediments and basement. It is essential to join the ODP(Ocean Drilling Program) that drills ocean basins and crusts using the drilling vessel with the ability of deploying almost 9 km of drilling string. The first year (1995) was focused on the analyzing the appropriateness Korea to join the ODP. The second year (1996) has been stressed on being an ODP member country based on results of the first year study, and planning the future activities as a member. The scope of study is joining the ODP as a Canada-Australia Consortium member and to set up the Korean ODP organization and future activities. The results and suggestions are as follows. 1) Necessities of Korea joining the ODP: If Korea becomes a member of the ODP, the benefits could be obtained based on the activities of other ODP members through academic, social and economic sectors. 2) Korean membership of ODP: Korea becomes a member of the Australia-Canada Consortium for ODP. AGSO (Austrian Geological Survey Organization), GSC (Geological Survey of Canada), and KIGAM (Korea Institute of Geology, Mining and Materials) on behalf of their own countries will each pay a share of the full member financial contribution to the ODP. AGSO and GSC will pay one third of the full member financial contribution, and KIGAM will pay one twelfth. 3) Korean ODP structure and future activities: To enhance the efficiency of initial activities after joining the ODP, it has been decided to have a relatively simple organization. The primary governing arm of the Korean ODP organizations is the Korean ODP

  4. Offshore drilling effects in Brazilian SE marine sediments: a meta-analytical approach.

    Science.gov (United States)

    Dore, Marina Pereira; Farias, Cássia; Hamacher, Cláudia

    2017-01-01

    The exploration and production of oil and gas reserves often result to drill cutting accumulations on the seafloor adjacent to drill locations. In this study, the detection of drilling influence on marine sediments was performed by meta-analytical comparison between data from pre- and post-drilling surveys undertaken in offshore Campos Basin, southeast of Brazil. Besides this overall appraisal on the geochemical variables, a multivariate assessment, considering only the post-drilling data, was performed. Among the variables, fines content, carbonates, total organic carbon, barium, chromium, copper, iron, manganese, nickel, lead, vanadium, zinc, and total petroleum hydrocarbons, only barium, copper, and hydrocarbons were related to drilling impacts. In relation to the point of discharge, relative elevated levels in the post-drilling campaigns were observed preferentially up to 500 m in the northeast and southwest directions, associated to the Brazil Current-predominant direction. Other distributed concentrations in the surroundings seem to indicate the dilution and dispersion of drilling waste promoted by meteoceanographic factors.

  5. The Impact of the 2002 Delaware Smoking Ordinance on Heart Attack and Asthma

    Directory of Open Access Journals (Sweden)

    Luis H. Solis

    2010-12-01

    Full Text Available In the United States, smoking is the leading cause of death - having a mortality rate of approximately 435,000 people in 2000—accounting for 8.1% of all US deaths recorded that year. Consequently, we analyzed the Delaware Hospital Discharge Database, and identified state and non-state residents discharged with AMI or asthma for the years 1999 to 2004. Statistical data analysis compared the incidence of AMI or asthma for each group before (1999–2002 and after (2003–2004 the amendment. As a result, we found that pre-ordinance and post-ordinance quarterly rates of AMI for Delaware residents were 451 (se = 21 and 430 (se = 21 respectively, representing a 4.7% reduction. Over the same time period, there was negligible change in the incidence of AMI for non-Delaware residents. After adjusting for population growth, the Risk Ratio (RR for asthma in Delaware residents post-ordinance was 0.95 (95% CI, 0.90 to 0.999, which represented a significant reduction (P = 0.046. By comparison, non-Delaware residents had an increased RR for asthma post-ordinance of 1.62 (95% CI, 1.46 to 1.86; P < 0.0001.The results suggest that Delaware’s comprehensive non-smoking ordinance effectively was associated with a statistically significant decrease in the incidence of AMI and asthma in Delaware residents when compared to non-Delaware residents.

  6. Drilling a borehole for LEP

    CERN Multimedia

    1981-01-01

    Boreholes were drilled along the earlier proposed line of the LEP tunnel under the Jura to find out the conditions likely to be encountered during the construction of the LEP tunnel (Annual Report 1981 p. 106, Fig. 10).

  7. Drilling Damage in Composite Material

    Directory of Open Access Journals (Sweden)

    Luís Miguel P. Durão

    2014-05-01

    Full Text Available The characteristics of carbon fibre reinforced laminates have widened their use from aerospace to domestic appliances, and new possibilities for their usage emerge almost daily. In many of the possible applications, the laminates need to be drilled for assembly purposes. It is known that a drilling process that reduces the drill thrust force can decrease the risk of delamination. In this work, damage assessment methods based on data extracted from radiographic images are compared and correlated with mechanical test results—bearing test and delamination onset test—and analytical models. The results demonstrate the importance of an adequate selection of drilling tools and machining parameters to extend the life cycle of these laminates as a consequence of enhanced reliability.

  8. Horizontal drilling activity in Manitoba

    Energy Technology Data Exchange (ETDEWEB)

    Fox, J.

    1997-04-01

    An update of horizontal well drilling in Manitoba was provided. Manitoba`s productive formations are: (1) the Bakken Formation, (2) the Lodgepole Formation, (3) the Mission Canyon Formation, (4) the Amaranth Formation, and (5) the Melita Formation. A total of 28 exploratory wells and 29 development wells, including 11 horizontal wells were drilled in 1996. The 11 horizontal wells accounted for 30 per cent of the drilling meterage. The leading drillers for horizontal wells in Manitoba are Tundra Oil and Gas, Chevron, Anderson and HCO. Production from horizontal wells in 1996 totaled 310 cubic meter per day. To date, no horizontal wells have been drilled in the Bakken Formation. The least successful horizontal well application has been in the Lodgepole Formation. A summary of horizontal well production was provided for each Formation. 4 tabs., 10 figs.

  9. Unit for cleaning drilling muds

    Energy Technology Data Exchange (ETDEWEB)

    Dorosh, M.M.; Dera, Ya.I.; Fesenko, M.M.; Makedonov, N.I.; Surkov, V.T.

    1983-01-01

    A design is proposed for a unit for cleaning drilling muds which includes a settling tank with input sleeve and a sleeve of the purified mud and hydrocyclones. In order to improve the effectiveness of the degree of purification, the unit is equipped with an ejector and sludge filter arranged under the settling tank in the form of a grid installed in the upper part of the settling tank and connected to the sleeve of purified mud, while the inlet sleeve is arranged tangentially. The proposed unit can operate during drilling with the use of muds on water and carbon bases. As a result of its use, the degree of purification of the drilling mud reaches 30-35%; there is an increase in mechanical drilling rate, the service life of the sand-separator and the silt separators and decrease in wear of the pump equipment.

  10. Geothermal drilling in Cerro Prieto

    Energy Technology Data Exchange (ETDEWEB)

    Dominguez A., Bernardo

    1982-08-10

    The number of characteristics of the different wells that have been drilled in the Cerro Prieto geothermal field to date enable one to summarize the basic factors in the applied technology, draw some conclusions, improve systems and procedures, and define some problems that have not yet been satisfactorily solved, although the existing solution is the best now available. For all practical purposes, the 100 wells drilled in the three areas or blocks into which the Cerro Prieto field has been divided have been completed. Both exploratory and production wells have been drilled; problems of partial or total lack of control have made it necessary to abandon some of these wells, since they were unsafe to keep in production or even to be used for observation and/or study. The wells and their type, the type of constructed wells and the accumulative meters that have been drilled for such wells are summarized.

  11. WATER QUALITY ANALYSIS OF AGRICULTURALLY IMPACTED TIDAL BLACKBIRD CREEK, DELAWARE

    Directory of Open Access Journals (Sweden)

    Matthew Stone

    2016-11-01

    Full Text Available Blackbird Creek, Delaware is a small watershed in northern Delaware that has a significant proportion of land designated for agricultural land use. The Blackbird Creek water monitoring program was initiated in 2012 to assess the condition of the watershed’s habitats using multiple measures of water quality. Habitats were identified based on percent adjacent agricultural land use. Study sites varying from five to fourteen were sampled biweekly during April and November, 2012-2015. Data were analyzed using principal component analysis and generalized linear modeling. Results from these first four years of data documented no significant differences in water quality parameters (dissolved oxygen, pH, temperature, salinity, inorganic nitrate, nitrite, ammonia, orthophosphate, alkalinity, and turbidity between the two habitats, although both orthophosphate and turbidity were elevated beyond EPA-recommended values. There were statistically significant differences for all of the parameters between agriculture seasons. The lack of notable differences between habitats suggests that, while the watershed is generally impacted by agricultural land use practices, there appears to be no impact on the surface water chemistry. Because there were no differences between habitats, it was concluded that seasonal differences were likely due to basic seasonal variation and were not a function of agricultural land use practices.

  12. Geothermal drill pipe corrosion test plan

    Energy Technology Data Exchange (ETDEWEB)

    Caskey, B.C.; Copass, K.S.

    1980-12-01

    Plans are presented for conducting a field test of drill pipe corrosion, comparing air and nitrogen as drilling fluids. This test will provide data for evaluating the potential of reducing geothermal well drilling costs by extending drill pipe life and reducing corrosion control costs. The 10-day test will take place during fall 1980 at the Baca Location in Sandoval County, New Mexico.

  13. The History of Gas Exploration in the Paleozoic Strata in Shaanxi-Gansu-Ningxia Basin

    Institute of Scientific and Technical Information of China (English)

    Jin Yantai

    1995-01-01

    @@ Shaanxi-Gansu-Ningxia Basin which covers an area of 250 000 km2 is one of the largest oil and gas basins, and also one of the basins having earlist history of oil and gas exploration in China.Up to now 87 years of exploration history have passed since the first oil productive well was drilled in Yanchang area in 1907.

  14. Development of CNPC's Drilling Business

    Institute of Scientific and Technical Information of China (English)

    Yang Qingli; Qin Wengui; Zheng Yi

    2011-01-01

    @@ With further exploration and development of oil and gas fields both at home and abroad, complicated geological conditions, poor quality of reserves and abominable working environment, drilling business, the largest of upstream petroleum industry in terms of total investment and scale, is facing new challenges.China National Petroleum Corporation (hereinafter referred to as CNPC) is in urgent need of transforming development patterns of drilling, so as to enhance competitiveness, improve production efficiency, and increase economic profits.

  15. Drilling of bone: a robust automatic method for the detection of drill bit break-through.

    Science.gov (United States)

    Ong, F R; Bouazza-Marouf, K

    1998-01-01

    The aim of this investigation is to devise a robust detection method for drill bit break-through when drilling into long bones using an automated drilling system that is associated with mechatronic assisted surgery. This investigation looks into the effects of system compliance and inherent drilling force fluctuation on the profiles of drilling force, drilling force, drilling between successive samples and drill bit rotational speed. It is shown that these effects have significant influences on the bone drilling related profiles and thus on the detection of drill bit break-through. A robust method, based on a Kalman filter, has been proposed. Using a modified Kalman filter, it is possible to convert the profiles of drilling force difference between successive samples and/or the drill bit rotational speed into easily recognizable and more consistent profiles, allowing a robust and repeatable detection of drill bit break-through.

  16. Steerable percussion air drilling system

    Energy Technology Data Exchange (ETDEWEB)

    Bui, H.D.; Oliver, M.S.; Gray, M.A.

    1993-12-31

    The cost-sharing contract between the US Department of Energy and Smith International provides the funding to further develop this concept into two complete steerable percussion air drilling system prototypes, each integrated with a navigation tool (wireline steering tool), a bend sub, stabilizing devices, and to conduct laboratory and field testing necessary to prepare the system for commercial realization. Such a system would make available for the first time the ability to penetrate earthen formations by the percussion method, using compressed air as the drilling fluid, and at the same time allow the directional control and steering of the drill bit. While the drill string is not rotating (slide mode), one can orient to build angle in the desired direction at a predictable rate. This build rate can be in the range of 1--20 degrees per one hundred feet and proceeds until the desired inclination or direction has been obtained. The drill pipe is then set in rotation, nullifying the effect of the bend angle, and causes the assembly to drill straight. The sliding procedure can be repeated as often as corrections for hole`s inclination or direction are needed.

  17. Biological effects of drilling wastes

    Energy Technology Data Exchange (ETDEWEB)

    Cranford, P. J. [Department of Fisheries and Oceans, Dartmouth, NS (Canada). Bedford Inst. of Oceanography

    2000-07-01

    An argument is made for the point of view that economic realities require that a sustainable fishery must co-exist with the offshore petroleum industry, and therefore to sustain the fishery comprehensive studies are needed to identify and minimize the impact of operational drilling wastes on fishery resources. Moreover, laboratory and field studies indicate that operational drilling platforms impact on fisheries at great distances, therefore studies should not be limited to the immediate vicinity of drilling sites. Studies on long-term exposure of resident organisms to low level contaminants and the chronic lethal and sublethal biological effects of production drilling wastes must be conducted under environmentally relevant conditions to ensure the validity of the results. Studies at the Bedford Institute of Oceanography on sea scallops (Placopecten magellanicus) shows them to be highly sensitive to impacts from drilling wastes. Results of these studies, integrated with toxicity data and information on the distribution and transport of drilling wastes have been used by regulatory agencies and industrial interests to develop scientifically sound and justifiable regulations. They also led to the development of practical, sensitive and cost-effective technologies that use resident resource species to detect environmental impacts at offshore production sites. 1 fig.

  18. Pseudo-outbreak of tuberculosis in poultry plant workers, Sussex County, Delaware.

    Science.gov (United States)

    Kim, Dennis Y; Ridzon, Renee; Giles, Beverly; Mireles, Teresa

    2002-12-01

    Delaware is a leading US poultry-producing state, and foreign-born workers make up a significant percentage of those employed by Delaware's poultry plants. In Sussex County, Delaware, a high percentage of the poultry workers are from two countries with a high incidence of tuberculosis (TB), Mexico and Guatemala, and thus are at risk for TB infection and disease. Furthermore, their risk of TB may be increased because many of these workers live in crowded conditions and lack access to medical care.

  19. Contamination Control for Scientific Drilling Operations.

    Science.gov (United States)

    Kallmeyer, J

    2017-01-01

    Drilling is an integral part of subsurface exploration. Because almost all drilling operations require the use of a drill fluid, contamination by infiltration of drill fluid into the recovered core material cannot be avoided. Because it is impossible to maintain sterile conditions during drilling the drill fluid will contain surface microbes and other contaminants. As contamination cannot be avoided, it has to be tracked to identify those parts of the drill core that were not infiltrated by the drill fluid. This is done by the addition of tracer compounds. A great variety of tracers is available, and the choice depends on many factors. This review will first explain the basic principles of drilling before presenting the most common tracers and discussing their strengths and weaknesses. The final part of this review presents a number of key questions that have to be addressed in order to find the right tracer for a particular drilling operation.

  20. Contrasting fish assemblages in free-flowing and impounded tributaries to the Upper Delaware River: Implications for conserving biodiversity

    Science.gov (United States)

    Baldigo, Barry P.; Delucia, Mari-Beth; Keller, Walter D.; Schuler, George E.; Apse, Colin D.; Moberg, Tara

    2015-01-01

    The Neversink River and the Beaver Kill in southeastern New York are major tributaries to the Delaware River, the longest undammed river east of the Mississippi. While the Beaver Kill is free flowing for its entire length, the Neversink River is subdivided by the Neversink Reservoir, which likely affects the diversity of local fish assemblages and health of aquatic ecosystems. The reservoir is an important part of the New York City waster-supply system that provides drinking water to more than 9 million people. Fish population and community data from recent quantitative surveys at comparable sites in both basins were assessed to characterize the differences between free-flowing and impounded rivers and the extent of reservoir effects to improve our capacity to define ecosystems responses that two modified flow-release programs (implemented in 2007 and 2011) should produce in the Neversink River. In general, the continuum of changes in fish assemblages which normally occur between headwaters and mouth was relatively uninterrupted in the Beaver Kill, but disrupted by the mid-basin impoundment in the Neversink River. Fish assemblages were also adversely affected at several acidified sites in the upper Neversink River, but not at most sites assessed herein. The reservoir clearly excluded diadromous species from the upper sub-basin, but it also substantially reduced community richness, diversity, and biomass at several mid-basin sites immediately downstream from the impoundment. There results will aid future attempts to determine if fish assemblages respond to more natural, yet highly regulated, flow regimes in the Neversink River. More important, knowledge gained from this study can help optimize use of valuable water resources while promoting species of special concern, such as American eel (Anguilla rostrata) and conserving biodiversity in Catskill Mountain streams.

  1. Drilling below the salt in the Western Mediterranean Sea : the GOLD-1 (Gulf of Lion Drilling) Project.

    Science.gov (United States)

    Rabineau, Marina; Aslanian, Daniel; Gorini, Christian; Alain, Karine; Participants, International

    2010-05-01

    In recent years the Gulf of Lion within the Occidental Mediterranean Sea has become a unique natural laboratory for the study both the evolution and interaction of deep processes (geodynamics, tectonics, subsidence, isostasy) and surficial processes (river behavior, sedimentary fluxes, sea-level changes, climatic impacts). Here, representing a large group of international researchers, we present the main objectives for a deep drilling project at the foot of the continental slope (2400 m water depth) in the Gulf of Lion. This position is the only place in the Gulf of Lion where the sedimentary column is expected to be complete without major erosional hiatuses or time gaps. It is located sufficiently far from the shelf and slope to not have been affected by the extraordinarly erosional event of the Messinian, and at the same time be free from salt-related faulting and diapirism. At this position we have recorded nearly a complete high-resolution history of the last 23 through 30 Ma of Mediterranean history in some 7.7 km of sedimentary archive. From the petroleum exploration perspective the deepest part of the margin reamain underexplored since all existing wells were drilled on the shelf and slope GLP1 & 2 being the deepest one. New interpretations in the region (especially concerning the Messinian event) have considerably changed earlier views of potential hydrocarbon reservoirs. New results expected from deep drilling are numerous: 1) For the substratum: the upper continental crust thins to less than 5 km, and changes laterally to a relatively thin crust with high velocities whose precise nature is still undetermined (Gailler et al., 2009). The aim of the drilling is to reach this crucial information which is essential for the understanding of the evolution of the sedimentary basin (Aslanian et al., 2009). 2) The drilling will allow the dating and characterization of the impact of the initiation and changes in glacioeustatic cyclicity in alpine glaciers and

  2. Trans-Amazon Drilling Project (TADP): origins and evolution of the forests, climate, and hydrology of the South American tropics

    Science.gov (United States)

    Baker, P. A.; Fritz, S. C.; Silva, C. G.; Rigsby, C. A.; Absy, M. L.; Almeida, R. P.; Caputo, M.; Chiessi, C. M.; Cruz, F. W.; Dick, C. W.; Feakins, S. J.; Figueiredo, J.; Freeman, K. H.; Hoorn, C.; Jaramillo, C.; Kern, A. K.; Latrubesse, E. M.; Ledru, M. P.; Marzoli, A.; Myrbo, A.; Noren, A.; Piller, W. E.; Ramos, M. I. F.; Ribas, C. C.; Trnadade, R.; West, A. J.; Wahnfried, I.; Willard, D. A.

    2015-12-01

    This article presents the scientific rationale for an ambitious ICDP drilling project to continuously sample Late Cretaceous to modern sediment in four different sedimentary basins that transect the equatorial Amazon of Brazil, from the Andean foreland to the Atlantic Ocean. The goals of this project are to document the evolution of plant biodiversity in the Amazon forests and to relate biotic diversification to changes in the physical environment, including climate, tectonism, and the surface landscape. These goals require long sedimentary records from each of the major sedimentary basins across the heart of the Brazilian Amazon, which can only be obtained by drilling because of the scarcity of Cenozoic outcrops. The proposed drilling will provide the first long, nearly continuous regional records of the Cenozoic history of the forests, their plant diversity, and the associated changes in climate and environment. It also will address fundamental questions about landscape evolution, including the history of Andean uplift and erosion as recorded in Andean foreland basins and the development of west-to-east hydrologic continuity between the Andes, the Amazon lowlands, and the equatorial Atlantic. Because many modern rivers of the Amazon basin flow along the major axes of the old sedimentary basins, we plan to locate drill sites on the margin of large rivers and to access the targeted drill sites by navigation along these rivers.

  3. Trans-Amazon Drilling Project (TADP): origins and evolution of the forests, climate, and hydrology of the South American tropics

    Science.gov (United States)

    Baker, P.A.; Fritz, S.C.; Silva, C.G.; Rigsby, C.A.; Absy, M.L.; Almeida, R.P.; Caputo, M.C.; Chiessi, C.M.; Cruz, F.W.; Dick, C.W.; Feakins, S.J.; Figueiredo, J.; Freeman, K.H.; Hoorn, C.; Jaramillo, C.A.; Kern, A.; Latrubesse, E.M.; Ledru, M.P.; Marzoli, A.; Myrbo, A.; Noren, A.; Piller, W.E.; Ramos, M.I.F.; Ribas, C.C.; Trinadade, R.; West, A.J.; Wahnfried, I.; Willard, Debra A.

    2015-01-01

    This article presents the scientific rationale for an ambitious ICDP drilling project to continuously sample Late Cretaceous to modern sediment in four different sedimentary basins that transect the equatorial Amazon of Brazil, from the Andean foreland to the Atlantic Ocean. The goals of this project are to document the evolution of plant biodiversity in the Amazon forests and to relate biotic diversification to changes in the physical environment, including climate, tectonism, and the surface landscape. These goals require long sedimentary records from each of the major sedimentary basins across the heart of the Brazilian Amazon, which can only be obtained by drilling because of the scarcity of Cenozoic outcrops. The proposed drilling will provide the first long, nearly continuous regional records of the Cenozoic history of the forests, their plant diversity, and the associated changes in climate and environment. It also will address fundamental questions about landscape evolution, including the history of Andean uplift and erosion as recorded in Andean foreland basins and the development of west-to-east hydrologic continuity between the Andes, the Amazon lowlands, and the equatorial Atlantic. Because many modern rivers of the Amazon basin flow along the major axes of the old sedimentary basins, we plan to locate drill sites on the margin of large rivers and to access the targeted drill sites by navigation along these rivers.

  4. Relevance of East African Drill Cores to Human Evolution: the Case of the Olorgesailie Drilling Project

    Science.gov (United States)

    Potts, R.

    2016-12-01

    Drill cores reaching the local basement of the East African Rift were obtained in 2012 south of the Olorgesailie Basin, Kenya, 20 km from excavations that document key benchmarks in the origin of Homo sapiens. Sediments totaling 216 m were obtained from two drilling locations representing the past 1 million years. The cores were acquired to build a detailed environmental record spatially associated with the transition from Acheulean to Middle Stone Age technology and extensive turnover in mammalian species. The project seeks precise tests of how climate dynamics and tectonic events were linked with these transitions. Core lithology (A.K. Behrensmeyer), geochronology (A. Deino), diatoms (R.B. Owen), phytoliths (R. Kinyanjui), geochemistry (N. Rabideaux, D. Deocampo), among other indicators, show evidence of strong environmental variability in agreement with predicted high-eccentricity modulation of climate during the evolutionary transitions. Increase in hominin mobility, elaboration of symbolic behavior, and concurrent turnover in mammalian species indicating heightened adaptability to unpredictable ecosystems, point to a direct link between the evolutionary transitions and the landscape dynamics reflected in the Olorgesailie drill cores. For paleoanthropologists and Earth scientists, any link between evolutionary transitions and environmental dynamics requires robust evolutionary datasets pertinent to how selection, extinction, population divergence, and other evolutionary processes were impacted by the dynamics uncovered in drill core studies. Fossil and archeological data offer a rich source of data and of robust environment-evolution explanations that must be integrated into efforts by Earth scientists who seek to examine high-resolution climate records of human evolution. Paleoanthropological examples will illustrate the opportunities that exist for connecting evolutionary benchmarks to the data obtained from drilled African muds. Project members: R. Potts, A

  5. Rotary steerable motor system for underground drilling

    Energy Technology Data Exchange (ETDEWEB)

    Turner, William E. (Durham, CT); Perry, Carl A. (Middletown, CT); Wassell, Mark E. (Kingwood, TX); Barbely, Jason R. (Middletown, CT); Burgess, Daniel E. (Middletown, CT); Cobern, Martin E. (Cheshire, CT)

    2010-07-27

    A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

  6. Rotary steerable motor system for underground drilling

    Science.gov (United States)

    Turner, William E.; Perry, Carl A.; Wassell, Mark E.; Barbely, Jason R.; Burgess, Daniel E.; Cobern, Martin E.

    2008-06-24

    A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

  7. Rotary steerable motor system for underground drilling

    Science.gov (United States)

    Turner, William E.; Perry, Carl A.; Wassell, Mark E.; Barbely, Jason R.; Burgess, Daniel E.; Cobern, Martin E.

    2010-07-27

    A preferred embodiment of a system for rotating and guiding a drill bit in an underground bore includes a drilling motor and a drive shaft coupled to drilling motor so that drill bit can be rotated by the drilling motor. The system further includes a guidance module having an actuating arm movable between an extended position wherein the actuating arm can contact a surface of the bore and thereby exert a force on the housing of the guidance module, and a retracted position.

  8. Advancement on Drilling Technology in Petroleum Industry

    OpenAIRE

    Akpedeye, Kelvin Uruemu

    2011-01-01

    Since the birth of petroleum business, in the mid-19th century, cable tool and rotary drilling have been the only two techniques applied in the drilling phase till date. Although the rotary drilling technique has proved very successful, applying laser technology in this drilling; which is a newer technology that is already at hand, has the potential of displacing both techniques from operation. Cable tool drilling is the first of these techniques. Hole boring is achieved by repeatedly lif...

  9. Successful drilling operations: Gold rush in the south; Erfolgreiche Bohrungen: Goldrausch im Sueden

    Energy Technology Data Exchange (ETDEWEB)

    Bernreuter, J.

    2006-01-31

    Since the community of Unterhaching has been successful with a drilling operation for a geothermal power plant in autumn 2004 the waiting list of further investors has become long in the region of Munich. The southern German molasse basin attracts them by means of favourable geological conditions. (orig.)

  10. A Resource Assessment Of Geothermal Energy Resources For Converting Deep Gas Wells In Carbonate Strata Into Geothermal Extraction Wells: A Permian Basin Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Erdlac, Richard J., Jr.

    2006-10-12

    for geothermal resources have been hindered. To increase the effective regional implementation of geothermal resources as an energy source for power production requires meeting several objectives. These include: 1) Expand (oil and gas as well as geothermal) industry awareness of an untapped source of geothermal energy within deep permeable strata of sedimentary basins; 2) Identify and target specific geographic areas within sedimentary basins where deeper heat sources can be developed; 3) Increase future geothermal field size from 10 km2 to many 100’s km2 or greater; and 4) Increase the productive depth range for economic geothermal energy extraction below the current 4 km limit by converting deep depleted and abandoned gas wells and fields into geothermal energy extraction wells. The first year of the proposed 3-year resource assessment covered an eight county region within the Delaware and Val Verde Basins of West Texas. This project has developed databases in Excel spreadsheet form that list over 8,000 temperature-depth recordings. These recordings come from header information listed on electric well logs recordings from various shallow to deep wells that were drilled for oil and gas exploration and production. The temperature-depth data is uncorrected and thus provides the lower temperature that is be expected to be encountered within the formation associated with the temperature-depth recording. Numerous graphs were developed from the data, all of which suggest that a log-normal solution for the thermal gradient is more descriptive of the data than a linear solution. A discussion of these plots and equations are presented within the narrative. Data was acquired that enable the determination of brine salinity versus brine density with the Permian Basin. A discussion on possible limestone and dolostone thermal conductivity parameters is presented with the purpose of assisting in determining heat flow and reservoir heat content for energy extraction. Subsurface

  11. A Resource Assessment Of Geothermal Energy Resources For Converting Deep Gas Wells In Carbonate Strata Into Geothermal Extraction Wells: A Permian Basin Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Erdlac, Richard J., Jr.

    2006-10-12

    for geothermal resources have been hindered. To increase the effective regional implementation of geothermal resources as an energy source for power production requires meeting several objectives. These include: 1) Expand (oil and gas as well as geothermal) industry awareness of an untapped source of geothermal energy within deep permeable strata of sedimentary basins; 2) Identify and target specific geographic areas within sedimentary basins where deeper heat sources can be developed; 3) Increase future geothermal field size from 10 km2 to many 100’s km2 or greater; and 4) Increase the productive depth range for economic geothermal energy extraction below the current 4 km limit by converting deep depleted and abandoned gas wells and fields into geothermal energy extraction wells. The first year of the proposed 3-year resource assessment covered an eight county region within the Delaware and Val Verde Basins of West Texas. This project has developed databases in Excel spreadsheet form that list over 8,000 temperature-depth recordings. These recordings come from header information listed on electric well logs recordings from various shallow to deep wells that were drilled for oil and gas exploration and production. The temperature-depth data is uncorrected and thus provides the lower temperature that is be expected to be encountered within the formation associated with the temperature-depth recording. Numerous graphs were developed from the data, all of which suggest that a log-normal solution for the thermal gradient is more descriptive of the data than a linear solution. A discussion of these plots and equations are presented within the narrative. Data was acquired that enable the determination of brine salinity versus brine density with the Permian Basin. A discussion on possible limestone and dolostone thermal conductivity parameters is presented with the purpose of assisting in determining heat flow and reservoir heat content for energy extraction. Subsurface

  12. 76 FR 26679 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Requirements for...

    Science.gov (United States)

    2011-05-09

    ... AGENCY 40 CFR Part 52 Approval and Promulgation of Air Quality Implementation Plans; Delaware; Requirements for Preconstruction Review, Prevention of Significant Deterioration AGENCY: Environmental... Regulation 1125, Requirements for Preconstruction Review, Prevention of Significant Deterioration (PSD) found...

  13. Inventory and Evaluation of Information on Delaware Bay, vol. 2, November 1972 (NODC Accession 7310520)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This is the second section of a three part study describing the history, land use, and legal mechanisms which operate in the tideland region of the lower Delaware...

  14. 77 FR 39456 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Section 110(a)(2...

    Science.gov (United States)

    2012-07-03

    ..., 89 Kings Highway, P.O. Box 1401, Dover, Delaware 19903. FOR FURTHER INFORMATION CONTACT: Rose Quinto... from Stephen D. Page, Director, Office of Air Quality Planning and Standards to the Regional...

  15. Accuracy Assessment Points Modified for Delaware Water Gap National Recreation Area Vegetation Mapping Project

    Data.gov (United States)

    National Park Service, Department of the Interior — Location of thematic accuracy assessment sampling points used in the vegetation and fire fuel model mapping in Delaware Water Gap National Recreation Area. In this...

  16. Field Plot Points Modified for Delaware Water Gap National Recreation Area Vegetation Mapping Project

    Data.gov (United States)

    National Park Service, Department of the Interior — Location of vegetation sampling plots use to collect data for vegetation classification and mapping at Delaware Water Gap National Recreation Area. In this data set,...

  17. Field Plot Points for Upper Delaware Scenic and Recreational River Vegetation Mapping Project

    Data.gov (United States)

    National Park Service, Department of the Interior — Location of vegetation sampling plots used to collect data for vegetation classification and mapping at Upper Delaware Scenic and Recreational River.

  18. EAARL Coastal Topography--Maryland and Delaware, post-Nor'Ida, 2009

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — A digital elevation model (DEM) of a portion of the eastern Maryland and Delaware coastline, post-Nor'Ida (November 2009 nor'easter), was produced from remotely...

  19. NOAA orthorectified Digital Elevation Model (DEM) image tiles, Bombay Hook, Delaware, 2011 (NODC Accession 0112173)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA Bombay Hook Project covers 177 square kilometers of the Bombay Hook National Wildlife Refuge and surrounding areas in Kent County, Delaware. The Dewberry...

  20. National Status and Trends: Bioeffects Assessment Program, Delaware Bay Summary Database (1997)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This study was based on the sediment quality triad (SQT) approach. A stratified probabilistic sampling design was utilized to characterize the Delaware Bay system in...

  1. EAARL Coastal Topography--Maryland and Delaware, post-Nor'Ida, 2009

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — A digital elevation model (DEM) of a portion of the eastern Maryland and Delaware coastline, post-Nor'Ida (November 2009 nor'easter), was produced from remotely...

  2. Social Vulnerability Index (SoVI) for Delaware based on 2000 Census Block Groups

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data depicts the social vulnerability of Delaware census block groups to environmental hazards. Data were culled primarily from the 2000 Decennial Census.

  3. 2011 Delaware Department of Natural Resources and Environmental Control (DNREC) Lidar: Bombay Hook National Wildlife Refuge

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Terrapoint collected LiDAR for over 177 square kilometers of the Bombay Hook National Wildlife Refuge in Kent County, Delaware. The nominal pulse spacing for this...

  4. Three Year Investigation Of Mosquito Breeding In Natural And Impounded Tidal Marshes In Delaware

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — From 1953 to 1955 the U. S. Fish and Wildlife Service and the University of Delaware Agricultural Experiment Station conducted a cooperative investigation of...

  5. Summary of the 1998 Spawning Survey of Horseshoe Crabs Along the Delaware Bay Shore

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The spawning survey of horseshoe crabs was conducted along the shores of Delaware Bay for the ninth year. Counts of spawning horseshoe crabs was performed by trained...

  6. Spatial Vegetation Data for Upper Delaware Scenic and Recreational River Vegetation Mapping Project

    Data.gov (United States)

    National Park Service, Department of the Interior — Vegetation map of the Upper Delaware Scenic and Recreational River provides local park-specific names for vegetation types, as well as crosswalks to the National...

  7. National Status and Trends: Bioeffects Assessment Program, Delaware Bay Summary Database (1997)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This study was based on the sediment quality triad (SQT) approach. A stratified probabilistic sampling design was utilized to characterize the Delaware Bay system...

  8. Continental scientific drilling program. [Los Alamos, New Mexico, July 17-21, 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-01

    The dynamics, structure, evolution, and genesis of the continents offer a major scientific challenge. At the same time, society faces many problems that require information about the continental crust for solution. A workshop on continental drilling for scientific purposes addressed the questions of how to maximize the scientific value of current and planned efforts of federal agencies and industry and how to supplement these efforts with holes drilled solely for scientific purpoes. Four panels addressed the scientific and associated societal problems relating to basement structures and deep continental basins, thermal regimes, mineral resources, and earthuqakes. These panels identified the main problems in each area that could be solved by information obtained from drill holes. A fifth panel considered needs for technological developments. The importance of a communications and coordinating mechanism to maximize the scientific results was noted. To this end, a Continental Scientific Drilling Program is outlined, including two advisory and guiding committees, one concerned with scientific objectives, the other with operations. (RWR)

  9. Microbiological Profiles of Deep Terrestrial Sedimentary Rocks Revealed by an Aseptic Drilling Procedure

    Science.gov (United States)

    Suzuki, Y.; Suko, T.; Fukuda, A.; Kouduka, M.; Nanba, K.; Sakata, S.; Ito, K.

    2009-12-01

    Unlike the near-surface environments, it is difficult to determine the community structure and biogeochemical functions of microorganisms in the deep subsurface mainly due to accessibility without contamination and disturbance. In an inland fore-arc basin in central Japan, we applied a new drilling procedure using deoxygenated and/or filter-sterilized drilling fluid(s). Although DNA-stained and cultivable cell numbers and the contents of phospholipid fatty acids (PLFA) all indicated the presence of metabolically active microbial populations in sedimentary rocks at a depth range from 200 to 350 m, it was not successful to extract DNA from the drilled core samples. During drilling, drilling fluid used for drilling and coring in the borehole was collected from the borehole bottom and subjected to DNA extraction. Quantitative fluorogenic PCR revealed that bacterial DNA were detected in drilling fluid samples when drilling was performed for siltstone and silty sandstone layers with the limited flow of drilling fluid. Bacterial 16S rRNA gene sequences retrieved from the drilling fluid samples below a depth of 324 m were mostly related to Pseudomonas putida or Flavobacterium succinicans, while those related to other Pseudomonas spp. were predominant at depths of 298 and 299m. PLFA profiles of core samples from a depth range between 250 and 351 m showed the abundance of 16:0, 16:1ω7 and 18:1ω9 fatty acids, which are known as major cellular lipid components of Pseudomonas and Flavobacterium spp. From these results, it was suggested that the members of the genera Pseudomonas and F. succinicans might represent dominant microbial populations that inhabit the deep terrestrial sedimentary rocks in Central Japan. This study was supported by grants from the Nuclear and Industrial Safety Agency (NISA) and Japan Nuclear Energy Safety Organization (JNES).

  10. Drilling force and temperature of bone under dry and physiological drilling conditions

    Science.gov (United States)

    Xu, Linlin; Wang, Chengyong; Jiang, Min; He, Huiyu; Song, Yuexian; Chen, Hanyuan; Shen, Jingnan; Zhang, Jiayong

    2014-11-01

    Many researches on drilling force and temperature have been done with the aim to reduce the labour intensiveness of surgery, avoid unnecessary damage and improve drilling quality. However, there has not been a systematic study of mid- and high-speed drilling under dry and physiological conditions(injection of saline). Furthermore, there is no consensus on optimal drilling parameters. To study these parameters under dry and physiological drilling conditions, pig humerus bones are drilled with medical twist drills operated using a wide range of drilling speeds and feed rates. Drilling force and temperature are measured using a YDZ-II01W dynamometer and a NEC TVS-500EX thermal infrared imager, respectively, to evaluate internal bone damage. To evaluate drilling quality, bone debris and hole morphology are observed by SEM(scanning electron microscopy). Changes in drilling force and temperature give similar results during drilling such that the value of each parameter peaks just before the drill penetrates through the osteon of the compact bone into the trabeculae of the spongy bone. Drilling temperatures under physiological conditions are much lower than those observed under dry conditions, while a larger drilling force occurs under physiological conditions than dry conditions. Drilling speed and feed rate have a significant influence on drilling force, temperature, bone debris and hole morphology. The investigation of the effect of drilling force and temperature on internal bone damage reveals that a drilling speed of 4500 r/min and a feed rate of 50 mm/min are recommended for bone drilling under physiological conditions. Drilling quality peaks under these optimal parameter conditions. This paper proposes the optimal drilling parameters under mid- and high-speed surgical drilling, considering internal bone damage and drilling quality, which can be looked as a reference for surgeons performing orthopedic operations.

  11. Drilling Force and Temperature of Bone under Dry and Physiological Drilling Conditions

    Institute of Scientific and Technical Information of China (English)

    XU Linlin; WANG Chengyong; JIANG Min; HE Huiyu; SONG Yuexian; CHEN Hanyuan; SHEN Jingnan; ZHANG Jiayong

    2014-01-01

    Many researches on drilling force and temperature have been done with the aim to reduce the labour intensiveness of surgery, avoid unnecessary damage and improve drilling quality. However, there has not been a systematic study of mid- and high-speed drilling under dry and physiological conditions(injection of saline). Furthermore, there is no consensus on optimal drilling parameters. To study these parameters under dry and physiological drilling conditions, pig humerus bones are drilled with medical twist drills operated using a wide range of drilling speeds and feed rates. Drilling force and temperature are measured using a YDZ-II01W dynamometer and a NEC TVS-500EX thermal infrared imager, respectively, to evaluate internal bone damage. To evaluate drilling quality, bone debris and hole morphology are observed by SEM(scanning electron microscopy). Changes in drilling force and temperature give similar results during drilling such that the value of each parameter peaks just before the drill penetrates through the osteon of the compact bone into the trabeculae of the spongy bone. Drilling temperatures under physiological conditions are much lower than those observed under dry conditions, while a larger drilling force occurs under physiological conditions than dry conditions. Drilling speed and feed rate have a significant influence on drilling force, temperature, bone debris and hole morphology. The investigation of the effect of drilling force and temperature on internal bone damage reveals that a drilling speed of 4500 r/min and a feed rate of 50 mm/min are recommended for bone drilling under physiological conditions. Drilling quality peaks under these optimal parameter conditions. This paper proposes the optimal drilling parameters under mid- and high-speed surgical drilling, considering internal bone damage and drilling quality, which can be looked as a reference for surgeons performing orthopedic operations.

  12. Berengario's drill: origin and inspiration.

    Science.gov (United States)

    Chorney, Michael A; Gandhi, Chirag D; Prestigiacomo, Charles J

    2014-04-01

    Craniotomies are among the oldest neurosurgical procedures, as evidenced by early human skulls discovered with holes in the calvaria. Though devices change, the principles to safely transgress the skull are identical. Modern neurosurgeons regularly use electric power drills in the operating theater; however, nonelectric trephining instruments remain trusted by professionals in certain emergent settings in the rare instance that an electric drill is unavailable. Until the late Middle Ages, innovation in craniotomy instrumentation remained stunted without much documented redesign. Jacopo Berengario da Carpi's (c. 1457-1530 CE) text Tractatus de Fractura Calvae sive Cranei depicts a drill previously unseen in a medical volume. Written in 1518 CE, the book was motivated by defeat over the course of Lorenzo II de'Medici's medical care. Berengario's interchangeable bit with a compound brace ("vertibulum"), known today as the Hudson brace, symbolizes a pivotal device in neurosurgery and medical tool design. This drill permitted surgeons to stock multiple bits, perform the craniotomy faster, and decrease equipment costs during a period of increased incidence of cranial fractures, and thus the need for craniotomies, which was attributable to the introduction of gunpowder. The inspiration stemmed from a school of thought growing within a population of physicians trained as mathematicians, engineers, and astrologers prior to entering the medical profession. Berengario may have been the first to record the use of such a unique drill, but whether he invented this instrument or merely adapted its use for the craniotomy remains clouded.

  13. DAME: planetary-prototype drilling automation.

    Science.gov (United States)

    Glass, B; Cannon, H; Branson, M; Hanagud, S; Paulsen, G

    2008-06-01

    We describe results from the Drilling Automation for Mars Exploration (DAME) project, including those of the summer 2006 tests from an Arctic analog site. The drill hardware is a hardened, evolved version of the Advanced Deep Drill by Honeybee Robotics. DAME has developed diagnostic and executive software for hands-off surface operations of the evolved version of this drill. The DAME drill automation tested from 2004 through 2006 included adaptively controlled drilling operations and the downhole diagnosis of drilling faults. It also included dynamic recovery capabilities when unexpected failures or drilling conditions were discovered. DAME has developed and tested drill automation software and hardware under stressful operating conditions during its Arctic field testing campaigns at a Mars analog site.

  14. Delaware River Dredging Disposal Study, Stage 1 Reconnaissance Report.

    Science.gov (United States)

    1979-06-01

    Ca :1 0 0 $ 41 >0 I pI1C 3 c a x oa C4 i-i :4n .- kip 0 *1 4+4 A.>A 44 C)p 0)- 144 to ~ 5 -4$ %4 a Lo 0 1 0) C: Go 14 V2 U) 4 14 1* 4 t $4 U 4 Cd 0 g a...a bank building to a private residence, this brick structure survives as an example of Greek Revival architecture. Nat. Reg. DK 116 Thorne Mansion...of Sydenham Thorne , an Anglican minister and co-founder of Milford, A.William Burton, Governor of Delaware and John M. Clayton, Secretary of State

  15. AURORA BOREALIS - Icebreaker, Drilling Platform and Multi-Purpose Research Vessel

    Science.gov (United States)

    Kunz-Pirrung, M.; Biebow, N.; Lembke-Jene, L.; Thiede, J.; Egerton, P.

    2007-12-01

    In spite of the critical role of the Arctic Ocean in climate evolution, it is the only sub-basin of the world's oceans that has essentially not been sampled by the drill ships of the Deep-Sea Drilling Project (DSDP) or the Ocean Drilling Program (ODP), and its long-term environmental history and tectonic structure is therefore poorly known. Exceptions are the ODP Leg 151 and the more recent very successful ACEX-expedition of the Integrated Ocean Drilling Program (IODP). This lack of data represents one of the largest gaps of information in modern Earth Science. Therefore, the new research icebreaker AURORA BOREALIS will be equipped with drilling facilities to fulfil the needs of the IODP for a -Mission-Specific Platform- to drill in deep, permanently ice-covered ocean basins. This icebreaker must be also powerful enough to maintain station against the drifting sea-ice cover and will have to be equipped with a dynamic positioning system. This new icebreaker would be conceived as an optimized science platform from the keel up and will allow conducting long, international and interdisciplinary expeditions into the central Arctic Ocean during all seasons of the year. In a long-term perspective the AURORA BOREALIS will also be used to address Antarctic research targets, both in its mode as a regular research vessel as well as a polar drill ship. The construction of AURORA BOREALIS requires several new technical implementations, such as advanced dynamic positioning and deep-sea drilling under a closed sea-ice cover and two moon pools (7 x 7 m), and will provide an extended technical potential and knowledge for marine technology. The scientific and technical details will be presented.

  16. The Towuti Drilling Project: paleoenvironments, biological evolution, and geomicrobiology of a tropical Pacific lake

    Science.gov (United States)

    Russell, James M.; Bijaksana, Satria; Vogel, Hendrik; Melles, Martin; Kallmeyer, Jens; Ariztegui, Daniel; Crowe, Sean; Fajar, Silvia; Hafidz, Abdul; Haffner, Doug; Hasberg, Ascelina; Ivory, Sarah; Kelly, Christopher; King, John; Kirana, Kartika; Morlock, Marina; Noren, Anders; O'Grady, Ryan; Ordonez, Luis; Stevenson, Janelle; von Rintelen, Thomas; Vuillemin, Aurele; Watkinson, Ian; Wattrus, Nigel; Wicaksono, Satrio; Wonik, Thomas; Bauer, Kohen; Deino, Alan; Friese, André; Henny, Cynthia; Imran; Marwoto, Ristiyanti; Ode Ngkoimani, La; Nomosatryo, Sulung; Ode Safiuddin, La; Simister, Rachel; Tamuntuan, Gerald

    2016-07-01

    The Towuti Drilling Project (TDP) is an international research program, whose goal is to understand long-term environmental and climatic change in the tropical western Pacific, the impacts of geological and environmental changes on the biological evolution of aquatic taxa, and the geomicrobiology and biogeochemistry of metal-rich, ultramafic-hosted lake sediments through the scientific drilling of Lake Towuti, southern Sulawesi, Indonesia. Lake Towuti is a large tectonic lake at the downstream end of the Malili lake system, a chain of five highly biodiverse lakes that are among the oldest lakes in Southeast Asia. In 2015 we carried out a scientific drilling program on Lake Towuti using the International Continental Scientific Drilling Program (ICDP) Deep Lakes Drilling System (DLDS). We recovered a total of ˜ 1018 m of core from 11 drilling sites with water depths ranging from 156 to 200 m. Recovery averaged 91.7 %, and the maximum drilling depth was 175 m below the lake floor, penetrating the entire sedimentary infill of the basin. Initial data from core and borehole logging indicate that these cores record the evolution of a highly dynamic tectonic and limnological system, with clear indications of orbital-scale climate variability during the mid- to late Pleistocene.

  17. Geologic report on the Sand Wash Drilling Project, Moffat and Routt Counties, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Carter, T.E.; Wayland, T.E.

    1981-09-01

    The Sand Wash Basin Drilling Project comprises twenty-seven (27) drill holes located in Moffat and Routt Counties, northwest Colorado, having an aggregate depth of 26,107.5 feet (7957.6 m). The holes penetrate the Browns Park Formation of Miocene age, which is a tuffaceous continental sandstone deposited in fluvial, eolian, and lacustrine environments. Partly based on project drilling results, uranium potential resource estimates for this formation in the $50/lb U/sub 3/O/sub 8/ forward-cost category have been increased by 34,476 tons U/sub 3/O/sub 8/ (35,036 metric tons). Three areas between Maybell and Craig, Colorado, considered favorable for uranium occurrences were verified as favorable by project drilling, and a fourth favorable area northwest of Maybell has been expanded. In addition, project drilling results indicate two new favorable areas, one north and northwest and one south of Steamboat Springs, Colorado. Anomalous radioactivity was detected in drill holes in all six study areas of the project. The most important factor in concentrating significant amounts of uranium in the target formation appears to be the availability of gaseous or liquid hydrocarbons and/or hydrogen sulfide gas as reductants. Where subjacent formations supply these reductants to the Browns Park Formation, project drilling encountered 0.05 percent to 0.01 percent uranium concentrations. Potential, though unproven, sources of these reductants are believed to underlie parts of all six project study areas.

  18. Upper Cenozoic sediments of the lower Delaware Valley and the northern Delmarva Peninsula, New Jersey, Pennsylvania, Delaware, and Maryland

    Science.gov (United States)

    Owens, James Patrick; Minard, James Pierson

    1979-01-01

    The 'yellow gravels' referred to by R. D. Salisbury in 1898 and the 'Trenton gravel,' as defined by H. C. Lewis in 1880, were investigated along the inner edge of the New Jersey Coastal Plain in southern New Jersey and in the northern Delmarva Peninsula. The highest level deposits, the Beacon Hill gravel, are found on only the highest hills in the New Jersey Coastal Plain. Their distribution suggests deposition from north to south across the plain. After deposition of the Beacon Hill, probably in middle or late Miocene time, a narrow valley was formed paralleling the inner edge of the New Jersey Coastal Plain between Raritan Bay and Camden. South of Camden, the valley broadened, covering much of southern New Jersey. The deposits in this valley are largely the Bridgeton Formation as we have redefined it. A second narrow valley was entrenched through the Bridgeton between Trenton and Salem, N.J. This valley broadens and covers much of the northern Delmarva Peninsula west of the Delaware River. The fill in the valley is largely the Pensauken Formation, as we have redefined it in our report. Collectively, the Beacon Hill, the Bridgeton, and the Pensauken were originally the 'yellow gravels' of Salisbury. These deposits are all fluviatile in origin and were largely formed as a series of step like downcutting channels. The Delaware Valley between Trenton and the lower Delaware Bay region is occupied by the 'Trenton gravel,' which is below the average level of the 'yellow gravels.' Two units recognized throughout the area and informally named the Spring Lake beds and the Van Sciver Lake beds are lithologically distinct from the 'yellow gravel' formations. The lithologies of the Spring Lake beds and the Van Sciver Lake beds are much more heterogeneous than those of the older formations. These two units, particularly, contain much greater amounts of silt and clay, often in thick beds. The depositional environments associated with the two units include fluviatile, estuarine

  19. Surface Currents and Winds at the Delaware Bay Mouth

    Energy Technology Data Exchange (ETDEWEB)

    Muscarella, P A; Barton, N P; Lipphardt, B L; Veron, D E; Wong, K C; Kirwan, A D

    2011-04-06

    Knowledge of the circulation of estuaries and adjacent shelf waters has relied on hydrographic measurements, moorings, and local wind observations usually removed from the region of interest. Although these observations are certainly sufficient to identify major characteristics, they lack both spatial resolution and temporal coverage. High resolution synoptic observations are required to identify important coastal processes at smaller scales. Long observation periods are needed to properly sample low-frequency processes that may also be important. The introduction of high-frequency (HF) radar measurements and regional wind models for coastal studies is changing this situation. Here we analyze synoptic, high-resolution surface winds and currents in the Delaware Bay mouth over an eight-month period (October 2007 through May 2008). The surface currents were measured by two high-frequency radars while the surface winds were extracted from a data-assimilating regional wind model. To illustrate the utility of these monitoring tools we focus on two 45-day periods which previously were shown to present contrasting pictures of the circulation. One, the low-outflow period is from 1 October through 14 November 2007; the other is the high-outflow period from 3 March through 16 April 2008. The large-scale characteristics noted by previous workers are clearly corroborated. Specifically the M2 tide dominates the surface currents, and the Delaware Bay outflow plume is clearly evident in the low frequency currents. Several new aspects of the surface circulation were also identified. These include a map of the spatial variability of the M2 tide (validating an earlier model study), persistent low-frequency cross-mouth flow, and a rapid response of the surface currents to a changing wind field. However, strong wind episodes did not persist long enough to set up a sustained Ekman response.

  20. Mycobacterial infections in striped bass from Delaware Bay

    Science.gov (United States)

    Ottinger, C.A.; Brown, J.J.; Densmore, Christine L.; Starliper, C.E.; Blazer, V.S.; Weyers, H.S.; Beauchamp, K.A.; Rhodes, M.W.; Kator, H.; Gauthier, David T.; Vogelbein, W.K.

    2007-01-01

    Eighty striped bass Morone saxatilis were obtained from Delaware Bay using commercial gill nets set adjacent to Woodland Beach (n = 70) and Bowers Beach (n = 10) in December 2003. Fish were examined for gross lesions. Total lengths (TLs) and eviscerated weights were determined to calculate condition factors (K). Portions of spleens were aseptically harvested for bacterial culture, and portions of spleens, kidneys (anterior and posterior), livers, and gonads were obtained for histological examination. The size distribution of the striped bass was relatively homogeneous; the mean TL was about 600 mm for all samples. Mean K exceeded 0.95 in all samples and was not significantly different (P > 0.05) among samples. Significant differences in mycobacterial infection prevalence (P ??? 0.05) were observed among samples; samples obtained at Woodland Beach (WB) on December 10 (53.8%, n = 13) and December 17 (7.1%, n = 42) exhibited the most striking differences in prevalence. Mycobacterial infection intensity ranged from 1 ?? 102 to 1 ?? 107 colony-forming units per gram of spleen. Acanthocephalan infection prevalence and intensity, non-acid-fast bacterial infection prevalence, and fish sex ratio were also significantly different among the samples (P ??? 0.05). Similar to the mycobacterial infections, differences in sex ratio, acanthocephalan infection, and non-acid-fast bacterial infection were observed between the WB samples taken on December 10 and 17. However, no significant associations (P > 0.05) were observed between sex ratio or these infections and mycobacterial infection. The differences in bacterial and parasite infection prevalence and intensity and fish sex ratio in some samples indicate that these fish had a different history and that the epizootiology of mycobacterial infection in striped bass from Delaware Bay may be relatively complex. ?? Copyright by the American Fisheries Society 2007.

  1. Addressing submarine geohazards through scientific drilling

    Science.gov (United States)

    Camerlenghi, A.

    2009-04-01

    multi-platform drilling of the Nankai seismogenic zone. Scientific initiatives are flourishing to drive IODP towards the study of submarine geohazards. In the last three years international workshops, were held to address the topic: ESF-ECORD sponsored a Magellan Workshop focussed on submarine landslides (Barcelona, Spain, 2006); IODP sponsored a world-wide Geohazard Workshop (Portland, Oregon, 2007); ESF-ECORD sponsored another Magellan Workshop focussed on Mediterranean submarine geohazards (Luleå, Sweden, 2008). In addition, following the ECORD-Net Conference on the Deep Sea Frontier (Naples, Italy, 2006), the history, monitoring and prediction of geohazards was identified as one of the 6 major areas for a European science plan to integrate Ocean Drilling, Ocean Margin, and Seabed research. More than 200 scientists and private companies representatives have been mobilized world-wide to attend these meetings, from where it emerged that Ocean Drilling will play a key role in the future to answer the following basic open questions on submarine geohazards: - What is the frequency, magnitude, and distribution of geohazard events? - Do precursory phenomena exist and can they be recognized? - What are the physical and mechanical properties of materials prone to failure? - What are the roles of preconditioning vs. triggering in rapid seafloor deformation? - Can the tsunamigenic potential of past and future events be assessed? Within the global-ocean geohazards, worth of note is the attention given in this preparatory phase to submarine geohazards in the Mediterranean basin, a miniature ocean often called a "natural laboratory" because of the diversity of geological environments it contains. The coastline is very densely-populated, totalling 160 million inhabitants sharing 46,000 km of coastline. The Mediterranean is the World's leading holiday destination, receiving an average of 135 million visitors annually. Submarine landslides, volcanic flank collapses, volcanic island

  2. Thickness of the surficial aquifer, Delmarva Peninsula, Maryland and Delaware

    Science.gov (United States)

    Denver, Judith; Nardi, Mark R.

    2017-01-01

    A digital map of the thickness of the surficial unconfined aquifer, including from the land surface and unsaturated zone to the bottom of sediments of geologic units identified as part of the surficial aquifer, was produced to improve understanding of the hydrologic system in the Maryland and Delaware portions of the Delmarva Peninsula. The map is intended to be used in conjunction with other environmental coverages (such land use, wetlands, and soil characteristics) to provide a subsurface hydrogeologic component to studies of nitrate transport that have historically relied on maps of surficial features. It could also be used to study the transport of other water soluble chemicals. The map was made using the best currently available data, which was of varying scales. It was created by overlaying a high resolution land surface and bathymetry digital elevation model (DEM) on a digital representation of the base of the surficial aquifer, part of hydrogeologic framework, as defined by Andreasen and others (2013). Thickness was calculated as the difference between the top of land surface and the bottom of the surficial aquifer sediments, which include sediments from geologic formations of late-Miocene through Quaternary age. Geologic formations with predominantly sandy surficial sediments that comprise the surficial aquifer on the Delmarva Peninsula include the Parsonsburg Sand, Sinepuxent Formation (Fm.), and parts of the Omar Fm. north of Indian River Bay in Delaware, the Columbia Fm., Beaverdam Fm., and Pennsauken Fm. (Ator and others 2005; Owens and Denney, 1986; Mixon, 1985; Bachman and Wilson, 1984). Formations with mixed texture and sandy stratigraphy including the Scotts Corner Fm. and Lynch Heights Fm. in Delaware are also considered part of the surficial aquifer (Ramsey, 1997). Subcropping aquifers and confining beds underlie the surficial aquifer throughout the Peninsula and may increase or limit its thickness, respectively (Andreasen and others, 2013

  3. Number & operations task & drill sheets

    CERN Document Server

    Reed, Nat

    2011-01-01

    For grades 6-8, our State Standards-based combined resource meets the number & operations concepts addressed by the NCTM standards and encourages the students to review the concepts in unique ways. The task sheets introduce the mathematical concepts to the students around a central problem taken from real-life experiences, while the drill sheets provide warm-up and timed practice questions for the students to strengthen their procedural proficiency skills. Included are problems involving place value, fractions, addition, subtraction and using money. The combined task & drill sheets offer spac

  4. 75 FR 54912 - Drill Pipe and Drill Collars From China

    Science.gov (United States)

    2010-09-09

    ... green tubes suitable for drill pipe), without regard to the specific chemistry of the steel (i.e... general application, consult the Commission's Rules of Practice and Procedure, part 201, subparts A... hearing and make oral presentations should attend a prehearing conference to be held at 9:30 a.m....

  5. Active Suppression of Drilling System Vibrations For Deep Drilling

    Energy Technology Data Exchange (ETDEWEB)

    Raymond, David W.; Blankenship, Douglas A.; Buerger, Stephen; Mesh, Mikhail; Radigan, William Thomas; Su, Jiann-Cherng

    2015-10-01

    The dynamic stability of deep drillstrings is challenged by an inability to impart controllability with ever-changing conditions introduced by geology, depth, structural dynamic properties and operating conditions. A multi-organizational LDRD project team at Sandia National Laboratories successfully demonstrated advanced technologies for mitigating drillstring vibrations to improve the reliability of drilling systems used for construction of deep, high-value wells. Using computational modeling and dynamic substructuring techniques, the benefit of controllable actuators at discrete locations in the drillstring is determined. Prototype downhole tools were developed and evaluated in laboratory test fixtures simulating the structural dynamic response of a deep drillstring. A laboratory-based drilling applicability demonstration was conducted to demonstrate the benefit available from deployment of an autonomous, downhole tool with self-actuation capabilities in response to the dynamic response of the host drillstring. A concept is presented for a prototype drilling tool based upon the technical advances. The technology described herein is the subject of U.S. Patent Application No. 62219481, entitled "DRILLING SYSTEM VIBRATION SUPPRESSION SYSTEMS AND METHODS", filed September 16, 2015.

  6. Drilling Systems for Extraterrestrial Subsurface Exploration

    Science.gov (United States)

    Zacny, K.; Bar-Cohen, Y.; Brennan, M.; Briggs, G.; Cooper, G.; Davis, K.; Dolgin, B.; Glaser, D.; Glass, B.; Gorevan, S.; Guerrero, J.; McKay, C.; Paulsen, G.; Stanley, S.; Stoker, C.

    2008-06-01

    Drilling consists of 2 processes: breaking the formation with a bit and removing the drilled cuttings. In rotary drilling, rotational speed and weight on bit are used to control drilling, and the optimization of these parameters can markedly improve drilling performance. Although fluids are used for cuttings removal in terrestrial drilling, most planetary drilling systems conduct dry drilling with an auger. Chip removal via water-ice sublimation (when excavating water-ice bound formations at pressure below the triple point of water) and pneumatic systems are also possible. Pneumatic systems use the gas or vaporization products of a high-density liquid brought from Earth, gas provided by an in situ compressor, or combustion products of a monopropellant. Drill bits can be divided into coring bits, which excavate an annular shaped hole, and full-faced bits. While cylindrical cores are generally superior as scientific samples, and coring drills have better performance characteristics, full-faced bits are simpler systems because the handling of a core requires a very complex robotic mechanism. The greatest constraints to extraterrestrial drilling are (1) the extreme environmental conditions, such as temperature, dust, and pressure; (2) the light-time communications delay, which necessitates highly autonomous systems; and (3) the mission and science constraints, such as mass and power budgets and the types of drilled samples needed for scientific analysis. A classification scheme based on drilling depth is proposed. Each of the 4 depth categories (surface drills, 1-meter class drills, 10-meter class drills, and deep drills) has distinct technological profiles and scientific ramifications.

  7. Don Juan Basin, Wright Valley, Antarctica: Model for Surface Processes on Mars

    Science.gov (United States)

    Englert, P.; Bishop, J. L.; Gibson, E. K.; Patel, S.; Koeberl, C.

    2014-09-01

    Mineral, chemical, and soluble salt composition of drill core samples from Don Juan Basin, Wright Valley, Antarctica, indicate that the formation of the most saline terrestrial pond may include groundwater discharge and near surface flow processes.

  8. Drilling to Supercritical Conditions: the Iceland Deep Drilling Project (IDDP).

    Science.gov (United States)

    Elders, W. A.; Fridleifsson, G. O.; Saito, S.

    2001-05-01

    Geothermal wells produce mixtures of water and steam in the range 200-350 C, however the high cost of drilling and completing these wells relative to the cost of oil and gas wells is a hindrance to the geothermal industry worldwide. Rather than trying only to reduce this cost, the Icelandic Deep Drilling Project (IDDP) is trying the approach of increasing the power output per well. Funded by a consortium of energy companies in Iceland, the IDDP plans to drill a series of boreholes, to depths greater than 4 to 5 km. The aim is to produce hydrothermal fluids systems at temperatures of 400-500 C, and to investigate the technical and economic aspects of producing supercritical fluids for use in power generation and other energy intensive processes, such as mineral recovery. The first phase feasibility and site selection study began in March 2001 and drilling of the first deep well is expected to begin in 2003. The IDDP faces difficult technical challenges to drill, complete, sample and maintain wells under hot, and potentially acid, conditions. However the IDDP also presents the opportunity to investigate very high-temperature hydrothermal regimes that have rarely been available for direct study. It will address important scientific issues, ranging from the coupling of magmatic and hydrothermal systems, supercritical phenomena, the transition from brittle to ductile behavior at relatively shallow depths, to land based analogues of submarine hot springs, the black smokers of the mid-ocean ridges. Fortunately, the IDDP industrial consortium is willing, or even anxious, to integrate its engineering activities with scientific investigations. The consortium will seek international participation by scientists and engineers to formulate a strategy to achieve both the engineering and scientific goals of the IDDP.

  9. Application of Ester based Drilling Fluid for Shale Gas Drilling

    Science.gov (United States)

    Sauki, Arina; Safwan Zazarli Shah, Mohamad; Bakar, Wan Zairani Wan

    2015-05-01

    Water based mud is the most commonly used mud in drilling operation. However, it is ineffective when dealing with water-sensitive shale that can lead to shale hydration, consequently wellbore instability is compromised. The alternative way to deal with this kind of shale is using synthetic-based mud (SBM) or oil-based mud (OBM). OBM is the best option in terms of technical requirement. Nevertheless, it is toxic and will create environmental problems when it is discharged to onshore or offshore environment. SBM is safer than the OBM. The aim of this research is to formulate a drilling mud system that can carry out its essential functions for shale gas drilling to avoid borehole instability. Ester based SBM has been chosen for the mud formulation. The ester used is methyl-ester C12-C14 derived from palm oil. The best formulation of ester-based drilling fluid was selected by manipulating the oil-water ratio content in the mud which are 70/30, 80/20 and 90/10 respectively. The feasibility of using this mud for shale gas drilling was investigated by measuring the rheological properties, shale reactivity and toxicity of the mud and the results were compared with a few types of OBM and WBM. The best rheological performance can be seen at 80/20 oil-water ratio of ester based mud. The findings revealed that the rheological performance of ester based mud is comparable with the excellent performance of sarapar based OBM and about 80% better than the WBM in terms of fluid loss. Apart from that, it is less toxic than other types of OBM which can maintain 60% prawn's survival even after 96 hours exposure in 100,000 ppm of mud concentration in artificial seawater.

  10. HIGH THROUGHPUT DRILLING OF TITANIUM ALLOYS

    Institute of Scientific and Technical Information of China (English)

    LI Rui; SHIH Albert Jau-Min

    2007-01-01

    The experiments of high throughput drilling of Ti-6Al-4V at 183 m/min cutting speed and 156 mm3/s material removal rate using a 4 mm diameter WC-Co spiral point drill are conducted. At this material removal rate, it took only 0.57 s to drill a hole in a 6.35 mm thick Ti plate. Supplying the cutting fluid via through-the-drill holes and the balance of cutting speed and feed have proven to be critical for drill life. An inverse heat transfer model is developed to predict the heat flux and the drill temperature distribution in drilling. A three-dimensional finite element modeling of drilling is conducted to predict the thrust force and torque. Experimental result demonstrates that, using proper machining process parameters, tool geometry, and fine-grained WC-Co tool material, the high throughput machining of Ti alloy is technically feasible.

  11. CNPC Exports Drilling Equipment to United States

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    @@ Beijing Petroleum Machinery Plant(BPM) of CNPC and Rowan Drilling Company Inc, one of the most powerful drilling service and driller manufacturing companies in the United States signed a petroleum equipment contract on December 9 in Beijing.

  12. Progress Made in Drilling Workers Training Pattern

    Institute of Scientific and Technical Information of China (English)

    Zhang Guozheng; Zhao Zhangbin

    1997-01-01

    @@ The Great Wall Drilling Workers Training Centre in North China Petroleum Workers College is specialized in training oil drilling technicians for China National Petroleum Corporation (CNPC), who will undertake the international contract and recontract.

  13. Zhongyuan Offers Drilling Service for Microbes

    Institute of Scientific and Technical Information of China (English)

    Zhang Zhiyu

    2001-01-01

    @@ No. 1 Drilling Company of Zhongyuan Petroleum Exploration Bureau and US-based Microbes Inc.signed a drilling engineering contract for six wells in Jilin Oil Field worth more than 11 million yuan in mid-October 2001.

  14. Geothermal well drilling manual at Cerro Prieto

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez P., A.; Flores S., M.

    1982-08-10

    The objective of the drilling manual is to solve all problems directly related to drilling during the construction of a well. In this case, the topics dealt which are drilling fluids and hydraulics to be applied in the field to improve drilling progress, eliminate risks and achieve good well-completion. There are other topics that are applicable such as drill bits and the drilling string, which are closely linked to drilling progress. On this occasion drilling fluid and hydraulics programs are presented, in addition to a computing program for a Casio FX-502P calculator to be applied in the field to optimize hydraulics and in the analysis of hydraulics for development and exploration wells at their different intervals.

  15. Pregnancy following laparoscopy ovarian drilling for clomiphene ...

    African Journals Online (AJOL)

    She achieved pregnancy following Laparoscopic Ovarian Drilling at the Assisted ... Conception following ovarian drilling. Omokanye .... advocated as this will drastically reduce the time to achieve ... laparoscopic laser diathermy in polycystic.

  16. Drilling azimuth gamma embedded design

    Directory of Open Access Journals (Sweden)

    Zhou Yi Ren

    2016-01-01

    Full Text Available Embedded drilling azimuth gamma design, the use of radioactive measuring principle embedded gamma measurement while drilling a short section analysis. Monte Carlo method, in response to the density of horizontal well logging numerical simulation of 16 orientation, the orientation of horizontal well analysed, calliper, bed boundary location, space, different formation density, formation thickness, and other factors inclined strata dip the impact by simulating 137Cs sources under different formation conditions of the gamma distribution, to determine the orientation of drilling density tool can detect window size and space, draw depth of the logging methods. The data 360° azimuth imaging, image processing method to obtain graph, display density of the formation, dip and strata thickness and other parameters, the logging methods obtain real-time geo-steering. To establish a theoretical basis for the orientation density logging while drilling method implementation and application of numerical simulation in-depth study of the MWD azimuth and density log response factors of horizontal wells.

  17. Phonetics drills in oral English

    Institute of Scientific and Technical Information of China (English)

    皮继伟

    2014-01-01

    Phonetics teaching is one of the important parts of English teaching .To improve the students’ pronunciation in oral English ,the paper indicates the relation between English phonetics and oral English, the problems of speech sounds, and the methods of phonetic drills.

  18. Phonetics drills in oral English

    Institute of Scientific and Technical Information of China (English)

    皮继伟

    2014-01-01

    Phonetics teaching is one of the important parts of English teaching.To improve the students’pronunciation in oral English,the paper indicates the relation between English phonetics and oral English,the problems of speech sounds,and the methods of phonetic drills.

  19. Facility for testing ice drills

    Science.gov (United States)

    Nielson, Dennis L.; Delahunty, Chris; Goodge, John W.; Severinghaus, Jeffery P.

    2017-05-01

    The Rapid Access Ice Drill (RAID) is designed for subsurface scientific investigations in Antarctica. Its objectives are to drill rapidly through ice, to core samples of the transition zone and bedrock, and to leave behind a borehole observatory. These objectives required the engineering and fabrication of an entirely new drilling system that included a modified mining-style coring rig, a unique fluid circulation system, a rod skid, a power unit, and a workshop with areas for the storage of supplies and consumables. An important milestone in fabrication of the RAID was the construction of a North American Test (NAT) facility where we were able to test drilling and fluid processing functions in an environment that is as close as possible to that expected in Antarctica. Our criteria for site selection was that the area should be cold during the winter months, be located in an area of low heat flow, and be at relatively high elevation. We selected a site for the facility near Bear Lake, Utah, USA. The general design of the NAT well (NAT-1) started with a 27.3 cm (10.75 in.) outer casing cemented in a 152 m deep hole. Within that casing, we hung a 14 cm (5.5 in.) casing string, and, within that casing, a column of ice was formed. The annulus between the 14 and 27.3 cm casings provided the path for circulation of a refrigerant. After in-depth study, we chose to use liquid CO2 to cool the hole. In order to minimize the likelihood of the casing splitting due to the volume increase associated with freezing water, the hole was first cooled and then ice was formed in increments from the bottom upward. First, ice cubes were placed in the inner liner and then water was added. Using this method, a column of ice was incrementally prepared for drilling tests. The drilling tests successfully demonstrated the functioning of the RAID system. Reproducing such a facility for testing of other ice drilling systems could be advantageous to other research programs in the future.

  20. SMART MONITORING AND DECISION MAKING FOR REGULATING ANNULUS BOTTOM HOLE PRESSURE WHILE DRILLING OIL WELLS

    Directory of Open Access Journals (Sweden)

    M. P. Vega

    Full Text Available Abstract Real time measurements and development of sensor technology are research issues associated with robustness and safety during oil well drilling operations, making feasible the diagnosis of problems and the development of a regulatory strategy. The major objective of this paper is to use an experimental plant and also field data, collected from a basin operation, offshore Brazil, for implementing smart monitoring and decision making, in order to assure drilling inside operational window, despite the commonly observed disturbances that produce fluctuations in the well annulus bottom hole pressure. Using real time measurements, the performance of a continuous automated drilling unit is analyzed under a scenario of varying levels of rate of penetration; aiming pressure set point tracking (inside the operational drilling window and also rejecting kick, a phenomenon that occurs when the annulus bottom hole pressure is inferior to the porous pressure, producing the migration of reservoir fluids into the annulus region. Finally, an empirical model was built, using real experimental data from offshore Brazil basins, enabling diagnosing and regulating a real drilling site by employing classic and advanced control strategies.

  1. 2.0 Introduction to the Delaware River Basin pilot study

    Science.gov (United States)

    Peter S. Murdoch; Jennifer C. Jenkins; Richard A. Birdsey

    2008-01-01

    The past 20 years of environmental research have shown that the environment is not made up of discrete components acting independently, but rather it is a mosaic of complex relationships among air, land, water, living resources, and human activities. The data collection and analytical capabilities of current ecosystem assessment and monitoring programs are insufficient...

  2. Carbonate gravity-flow processes on the Lower Permian slope, northwest Delaware basin

    Energy Technology Data Exchange (ETDEWEB)

    Loucks, R.G.; Brown, A.A.; Achauer, C.W. (ARCO Oil and Gas Co., Plano, TX (United States))

    1991-03-01

    Wolfcampian carbonate gravity-flow deposits accumulated on a low-angle slope in front of a platform of relatively low relief ({approximately}220 m). A 25 m core, located approximately 15 km basinward of the self margin, was examined to determine processes of carbonate deposition in the middle to distal slope environments. The majority of the deposits are cohesive debris-flows composed of clast-supported conglomerates with a calcareous siliciclastic mudstone matrix. Other deposits include high- and low-density turbidites of lime packstones (sand- to boulder-size range), lime grainstones, and siliclastic muddy silstones and suspension deposits of calcareous siliciclastic mudstones. Cohesive debris flows are generally massive and structureless, although several flows show an inverse-graded zone at their base indicating dispersive pressure forces that developed in a traction carpet. Other flows display coarse-tail fining-upward sequences indicating deposition by suspension settling from liquefied flow. At the base of each high-density, gravelly turbidite is one to several inversely graded zones of carbonated clasts indicating a traction carpet zone. These traction carpets are overlain by normal-graded units of shell and clast material. The upper units appear to be deposited directly out of suspension. The low-density turbidites are interpreted to be the residual products of more shelfward-deposited debris flows and high-density turbidity currents. Many of the depositional features described here for carbonate gravity-flow deposits are identical to those in siliclastic deposits, therefore the depositional processes controlling these features are probably similar.

  3. Method comparison for forest soil carbon and nitrogen estimates in the Delaware River basin

    Science.gov (United States)

    B. Xu; Yude Pan; A.H. Johnson; A.F. Plante

    2016-01-01

    The accuracy of forest soil C and N estimates is hampered by forest soils that are rocky, inaccessible, and spatially heterogeneous. A composite coring technique is the standard method used in Forest Inventory and Analysis, but its accuracy has been questioned. Quantitative soil pits provide direct measurement of rock content and soil mass from a larger, more...

  4. The Delaware River Basin Collaborative Environmental Monitoring and Research Initiative: Foundation Document

    Science.gov (United States)

    Peter S. Murdoch; Jennifer C. Jenkins; Richard A. Birdsey

    2008-01-01

    The U.S. Forest Service, the U.S. Geological Survey, and the National Park Service formed the Collaborative Environmental Monitoring and Research Initiative (CEMRI) to test strategies for integrated environmental monitoring among the agencies. The initiative combined monitoring and research efforts of the participating Federal programs to evaluate health and...

  5. RESERVES IN WESTERN BASINS PART IV: WIND RIVER BASIN

    Energy Technology Data Exchange (ETDEWEB)

    Robert Caldwell

    1998-04-01

    Vast quantities of natural gas are entrapped within various tight formations in the Rocky Mountain area. This report seeks to quantify what proportion of that resource can be considered recoverable under today's technological and economic conditions and discusses factors controlling recovery. The ultimate goal of this project is to encourage development of tight gas reserves by industry through reducing the technical and economic risks of locating, drilling and completing commercial tight gas wells. This report is the fourth in a series and focuses on the Wind River Basin located in west central Wyoming. The first three reports presented analyses of the tight gas reserves and resources in the Greater Green River Basin (Scotia, 1993), Piceance Basin (Scotia, 1995) and the Uinta Basin (Scotia, 1995). Since each report is a stand-alone document, duplication of language will exist where common aspects are discussed. This study, and the previous three, describe basin-centered gas deposits (Masters, 1979) which contain vast quantities of natural gas entrapped in low permeability (tight), overpressured sandstones occupying a central basin location. Such deposits are generally continuous and are not conventionally trapped by a structural or stratigraphic seal. Rather, the tight character of the reservoirs prevents rapid migration of the gas, and where rates of gas generation exceed rates of escape, an overpressured basin-centered gas deposit results (Spencer, 1987). Since the temperature is a primary controlling factor for the onset and rate of gas generation, these deposits exist in the deeper, central parts of a basin where temperatures generally exceed 200 F and drill depths exceed 8,000 feet. The abbreviation OPT (overpressured tight) is used when referring to sandstone reservoirs that comprise the basin-centered gas deposit. Because the gas resources trapped in this setting are so large, they represent an important source of future gas supply, prompting studies

  6. Jet Drilling and Optimizing Parameter Drilling Technology in Shengli Oil Fields

    Institute of Scientific and Technical Information of China (English)

    Chen Yue; Peng Junsheng

    1996-01-01

    @@ In Shengli oilfield, remarkable achievements have been obtained in research and tests on the technologies of jet drilling and optimizing parameter drilling, extensive applications of the technologies have greatly improved drilling speed and sharply decreased drilling time and costs, thus achieving excellent social and economic benefits.

  7. Drill cuttings mount formation study

    Science.gov (United States)

    Teh, Su Yean; Koh, Hock Lye

    2014-07-01

    Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

  8. Direction of drilling wells. Wiercenie otworow kierunkowych

    Energy Technology Data Exchange (ETDEWEB)

    Szostak, L.

    1980-01-01

    In the example of the most widespread drilling of vertical wells, an examination is made of the mining-geological and technical-technological reasons and methods for evaluating the amount of their twisting. Methods are presented for stabilizing the drilling shaft, features of drilling vertical wells by turbodrills and groups of wells for freezing rocks. Characteristics are presented for the features of directional drilling, model profiles of directed wells, drilling of wells with assigned deviation of the face from the vertical axis. Possibilities are indicated for controlling the trajectory of movement of the face of the well with the rotary method of drilling, in particular, with the use of a deviating wedge, cement plug, etc., methods of drilling inclined wells on cased and uncased sections. Features are examined of creating and controlling the inclination of a well with the use of turbodrills of different design, technology of drilling and casing of multiple-face wells, drilling of a fan of wells from one position of the drilling unit, for example, with unfavorable relief of the earth's surface and drilling of offshore wells by using floating drilling units.

  9. 25 CFR 226.33 - Line drilling.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Line drilling. 226.33 Section 226.33 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ENERGY AND MINERALS LEASING OF OSAGE RESERVATION LANDS FOR OIL AND GAS MINING Requirements of Lessees § 226.33 Line drilling. Lessee shall not drill within 300...

  10. 30 CFR 256.71 - Directional drilling.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Directional drilling. 256.71 Section 256.71... drilling. In accordance with an approved exploration plan or development and production plan, a lease may be maintained in force by directional wells drilled under the leased area from surface locations...

  11. Diamond Drilling Specification Manual and Course Outline.

    Science.gov (United States)

    British Columbia Dept. of Education, Victoria.

    This publication presents the standards required of a person practicing diamond drilling in western Canada and provides an outline for teaching the skills and knowledge. It is divided into two parts. The Diamond Drilling Specification Manual establishes the levels of skill and knowledge required in the four certified levels of diamond drilling.…

  12. China Drills Its First "Earth Hole"

    Institute of Scientific and Technical Information of China (English)

    Yang Qingwen

    2001-01-01

    @@ On August 4, 2001, drilling of Kezuan-1 Well, the first continental scientific exploration well in China, was officially kicked off in Donghai County,Jiangsu Province. About 1000 people including high-ranking governmental officials and famous experts attended the drilling ceremony. Vice Chairman of the Chinese People's Political Consultative Conference Wan Guoquan pressed the button to start drilling of the exploration well.

  13. Near real time water resources data for river basin management

    Science.gov (United States)

    Paulson, R. W. (Principal Investigator)

    1973-01-01

    The author has identified the following significant results. Twenty Data Collection Platforms (DCP) are being field installed on USGS water resources stations in the Delaware River Basin. DCP's have been successfully installed and are operating well on five stream gaging stations, three observation wells, and one water quality monitor in the basin. DCP's have been installed at nine additional water quality monitors, and work is progressing on interfacing the platforms to the monitors. ERTS-related water resources data from the platforms are being provided in near real time, by the Goddard Space Flight Center to the Pennsylvania district, Water Resources Division, U.S. Geological Survey. On a daily basis, the data are computer processed by the Survey and provided to the Delaware River Basin Commission. Each daily summary contains data that were relayed during 4 or 5 of the 15 orbits made by ERTS-1 during the previous day. Water resources parameters relays by the platforms include dissolved oxygen concentrations, temperature, pH, specific conductance, well level, and stream gage height, which is used to compute stream flow for the daily summary.

  14. Petroleum in the Junggar basin, northwestern China

    Science.gov (United States)

    Taner, Irfan; Kamen-Kaye, Maurice; Meyerhoff, Arthur A.

    The Junggar basin occupies a large triangular area of some 130 000 km 2 in northwestern China. Situated between the Altay Shan (Altay Range) on the northeast and the Tian Shan (Tian Range) on the southwest, and between lesser ranges around the remainder of its periphery, the Junggar basin is completely intermontane. Its history as a basin began in the Permian, and continued as various uplifts and downwarps evolved. Through the Paleozoic the characteristics of the Junggar basin area were largely geosynclinal and marine. Its post-Permian development took place exclusively in continental regimes. Inhabitants of the Junggar basin have known and utilized its numerous oil and asphalt seeps and its spectacular spreads of asphalt for more than 2000 years, especially in the Karamay-Urho thrust belt near the northwestern rim. The first discovery of oil in the modern sense came at Dushanzi, one of the steeply folded anticlines of theÜrümqi foredeep near the southern rim. The first shallow oil in the Karamay-Urho thrust belt came in 1937, followed by commercial production in the Karamay field in 1955. Output continued to be modest until wells were drilled through local thrusts and reverse faults in the early 1980s. By 1985, cumulative production of the Karamay group of fields had reached 42,000,000 t (metric tonnes) (306,000,000 bbl), with a calculated minimum ultimate recovery of 280,000,000 t (2 billion bbl). Principal production comes from Permian and Triassic strata in continental facies. Apart from marine Mid and Upper Carboniferous strata, source rocks occur mainly in fine-grained lacustrine detrital beds of the Permian, the Triassic, the Jurassic and the Tertiary. Several uplifts and downwarps elsewhere in the Junggar basin remain to be drilled comprehensively. Results from such drilling may enhance the very important position that the Junggar already has attained in the hierarchy of China's onshore basins.

  15. Designing virtual science labs for the Islamic Academy of Delaware

    Science.gov (United States)

    AlZahrani, Nada Saeed

    Science education is a basic part of the curriculum in modern day classrooms. Instructional approaches to science education can take many forms but hands-on application of theory via science laboratory activities for the learner is common. Not all schools have the resources to provide the laboratory environment necessary for hands-on application of science theory. Some settings rely on technology to provide a virtual laboratory experience instead. The Islamic Academy of Delaware (IAD), a typical community-based organization, was formed to support and meet the essential needs of the Muslim community of Delaware. IAD provides science education as part of the overall curriculum, but cannot provide laboratory activities as part of the science program. Virtual science labs may be a successful model for students at IAD. This study was conducted to investigate the potential of implementing virtual science labs at IAD and to develop an implementation plan for integrating the virtual labs. The literature has shown us that the lab experience is a valuable part of the science curriculum (NBPTS, 2013, Wolf, 2010, National Research Council, 1997 & 2012). The National Research Council (2012) stressed the inclusion of laboratory investigations in the science curriculum. The literature also supports the use of virtual labs as an effective substitute for classroom labs (Babateen, 2011; National Science Teachers Association, 2008). Pyatt and Simms (2011) found evidence that virtual labs were as good, if not better than physical lab experiences in some respects. Although not identical in experience to a live lab, the virtual lab has been shown to provide the student with an effective laboratory experience in situations where the live lab is not possible. The results of the IAD teacher interviews indicate that the teachers are well-prepared for, and supportive of, the implementation of virtual labs to improve the science education curriculum. The investigator believes that with the

  16. Methods to ensure optimal off-bottom and drill bit distance under pellet impact drilling

    OpenAIRE

    Kovalev, Artem Vladimirovich; Isaev, Evgeniy Dmitrievich; Vagapov, A. R.; Urnish, V. V.; Ulyanova, Oksana Sergeevna

    2016-01-01

    The paper describes pellet impact drilling which could be used to increase the drilling speed and the rate of penetration when drilling hard rock for various purposes. Pellet impact drilling implies rock destruction by metal pellets with high kinetic energy in the immediate vicinity of the earth formation encountered. The pellets are circulated in the bottom hole by a high velocity fluid jet, which is the principle component of the ejector pellet impact drill bit. The paper presents the surve...

  17. REDUCTION OF AN ADVERSE IMPACT DURING WELL DRILLING BY MEANS OF DRILLING WASTE USAGE

    OpenAIRE

    Vladimir Sergeevich Kuznetsov; Igor Konstantinovich Suprun

    2017-01-01

    The problem of drilling waste utilisation is assumed to be resolved through the implementation of the complex of environment protection production engineering measures. This includes, firstly, the usage in the process of well drilling of drilling mud on the basis of water-soluble biodegradable polymers and a four-stage drilling mud refining system. Secondly, the usage of the well site construction with trenching for allocation of expressed bore mud and a temporary ground tank for drilling was...

  18. REDUCTION OF AN ADVERSE IMPACT DURING WELL DRILLING BY MEANS OF DRILLING WASTE USAGE

    Directory of Open Access Journals (Sweden)

    Vladimir Sergeevich Kuznetsov

    2017-03-01

    Full Text Available The problem of drilling waste utilisation is assumed to be resolved through the implementation of the complex of environment protection production engineering measures. This includes, firstly, the usage in the process of well drilling of drilling mud on the basis of water-soluble biodegradable polymers and a four-stage drilling mud refining system. Secondly, the usage of the well site construction with trenching for allocation of expressed bore mud and a temporary ground tank for drilling waste water.

  19. Microhole Drilling Tractor Technology Development

    Energy Technology Data Exchange (ETDEWEB)

    Western Well Tool

    2007-07-09

    In an effort to increase the U.S. energy reserves and lower costs for finding and retrieving oil, the USDOE created a solicitation to encourage industry to focus on means to operate in small diameter well-Microhole. Partially in response to this solicitation and because Western Well Tool's (WWT) corporate objective to develop small diameter coiled tubing drilling tractor, WWT responded to and was awarded a contract to design, prototype, shop test, and field demonstrate a Microhole Drilling Tractor (MDT). The benefit to the oil industry and the US consumer from the project is that with the MDT's ability to facilitate Coiled Tubing drilled wells to be 1000-3000 feet longer horizontally, US brown fields can be more efficiently exploited resulting in fewer wells, less environmental impact, greater and faster oil recovery, and lower drilling costs. Shortly after award of the contract, WWT was approached by a major oil company that strongly indicated that the specified size of a tractor of 3.0 inches diameter was inappropriate and that immediate applications for a 3.38-inch diameter tractor would substantially increase the usefulness of the tool to the oil industry. Based on this along with an understanding with the oil company to use the tractor in multiple field applications, WWT applied for and was granted a no-cost change-of-scope contract amendment to design, manufacture, assemble, shop test and field demonstrate a prototype a 3.38 inch diameter MDT. Utilizing existing WWT tractor technology and conforming to an industry developed specification for the tool, the Microhole Drilling Tractor was designed. Specific features of the MDT that increase it usefulness are: (1) Operation on differential pressure of the drilling fluid, (2) On-Off Capability, (3) Patented unique gripping elements (4) High strength and flexibility, (5) Compatibility to existing Coiled Tubing drilling equipment and operations. The ability to power the MDT with drilling fluid results in a

  20. Improved Hardfacing for Drill Bits and Drilling Tools

    Science.gov (United States)

    Sue, Albert; Sreshta, Harry; Qiu, Bao He

    2011-01-01

    New flame spray hardfacing, DSH (DuraShell® Steel Hardfacing, US patent pending), was developed to improve thermal conductivity, abrasion wear, and erosion resistance for subterranean drilling application. The materials consisted of spherical cast WC/W2C and Ni-Si-B alloy powders. The hardfacing compositions were tailored for various processes such as flame spray and laser cladding. Typically, the hardfacing comprised hard tungsten carbide particles being uniformly distributed in a tough Ni-alloy matrix. The hardness of WC/W2C exceeded 2300 Hv.3 and that of Ni-alloy matrix varied from about 400 to 700 Hv.3. High- and low-stress abrasion resistances of these hardfacing materials were characterized and compared to the conventional hard coatings of cast WC/W2C and Ni-Cr-Si-B-Fe. The increase in thermal, wear, and erosion resistances of the hardfacing improved the durability of PDC (polycrystalline diamond compact) steel body bit and drilling tools and their cost-effective performance. Several case studies of DSH hardfacings on drill bits were described.

  1. Approximately-Balanced Drilling in Daqing Oilfield

    Institute of Scientific and Technical Information of China (English)

    Xia Bairu; Zheng Xiuhua; Li Guoqing; Tian Tuo

    2004-01-01

    The Daqing oilfield is a multilayered heterogeneous oil field where the pressure are different in the same vertical profile causing many troubles to the adjustment well drillings. The approximately-balanced drilling technique has been developed and proved to be efficient and successful in Daqing oilfield. This paper discusses the application of approximately-balanced drilling technique under the condition of multilayered pressure in Daqing oilfield, including the prediction of formation pressure, the pressure discharge technique for the drilling well and the control of the density of drilling fluid.

  2. Water quality in the surficial aquifer near agricultural areas in the Delaware Coastal Plain, 2014

    Science.gov (United States)

    Fleming, Brandon J.; Mensch, Laura L.; Denver, Judith M.; Cruz, Roberto M.; Nardi, Mark R.

    2017-07-27

    The U.S. Geological Survey, in cooperation with the Delaware Department of Agriculture, developed a network of wells to monitor groundwater quality in the surficial aquifer of the Delaware Coastal Plain. Well-drained soils, a flat landscape, and accessible water in the Delaware Coastal Plain make for a productive agricultural setting. As such, agriculture is one of the largest industries in the State of Delaware. This setting enables the transport of chemicals from agriculture and other land uses to shallow groundwater. Efforts to mitigate nutrient transport to groundwater by the implementation of agricultural best management practices (BMPs) have been ongoing for several decades. To measure the effectiveness of BMPs on a regional scale, a network of 48 wells was designed to measure shallow groundwater quality (particularly nitrate) over time near agricultural land in the Delaware Coastal Plain. Water characteristics, major ions, nutrients, and dissolved gases were measured in groundwater samples collected from network wells during fall 2014. Wells were organized into three groups based on their geochemical similarity and these groups were used to describe nitrate and chloride concentrations and factors that affect the variability among the groups. The results from this study are intended to establish waterquality conditions in 2014 to enable comparison of future conditions and evaluate the effectiveness of agricultural BMPs on a regional scale.

  3. Long hole waterjet drilling for gas drainage

    Energy Technology Data Exchange (ETDEWEB)

    Matt Stockwell; M. Gledhill; S. Hildebrand; S. Adam; Tim Meyer [CMTE (Australia)

    2003-04-01

    In-seam drilling for gas drainage is now an essential part of operations at many Australian underground coalmines. The objective of this project is to develop and trial a new drilling method for the accurate and efficient installation of long inseam boreholes (>1000 metres). This involves the integration of pure water-jet drilling technology (i.e. not water-jet assisted rotary drilling) developed by CMTE with conventional directional drilling technology. The system was similar to conventional directional drilling methods, but instead of relying on a down-hole-motor (DHM) rotating a mechanical drill bit for cutting, high pressure water-jets were used. The testing of the system did not achieve the full objectives set down in the project plan. A borehole greater than 1000 metres was not achieved. The first trial site had coal that was weathered, oxidized and dry. These conditions significantly affected the ability of the drilling tool to stay 'in-seam'. Due to the poor conditions at the first trial, many experimental objectives were forwarded to the second field trial. In the second trial drilling difficulties were experienced, this was due to the interaction between the confinement of the borehole and the dimensions of the down hole drilling assembly. This ultimately reduced the productivity of the system and the distance that could be drilled within the specified trial periods. Testing in the first field trial did not show any indication that the system would have this difficulty.

  4. Modeling and experimentation of bone drilling forces.

    Science.gov (United States)

    Lee, JuEun; Gozen, B Arda; Ozdoganlar, O Burak

    2012-04-05

    Prediction and control of bone drilling forces are critical to the success of many orthopaedic operations. Uncontrolled and large forces can cause drill-bit breakage, drill breakthrough, excessive heat generation, and mechanical damage to the bone. This paper presents a mechanistic model for prediction of thrust forces and torques experienced during bone drilling. The model incorporates the radially varying drill-bit geometry and cutting conditions analytically, while capturing the material and friction properties empirically through a specific energy formulation. The forces from the chisel edge are modeled by considering the indentation process that occurs in the vicinity of the drill-bit axis. A procedure is outlined to calibrate the specific energies, where only a small number of calibration experiments are required for a wide range of drilling conditions and drill-bit geometry. The calibration parameters for the cortical portions of bovine tibia are identified through drilling tests. Subsequently, a series of validation tests are conducted under different feed rates and spindle speeds. The thrust forces and torques were observed to vary considerably between bones from different animals. The forces from the model were seen to match well with those from the experimentation within the inherent variations from the bone characteristics. The model can be used to select favorable drilling conditions, to assist in robotic surgeries, and to design optimal orthopaedic drill bits. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. FY 1983 Funding for ocean drilling

    Science.gov (United States)

    Richman, Barbara T.

    Proposed funding for scientific ocean drilling within the National Science Foundation (NSF) in fiscal 1983 totals $14 million, $6 million less than the current fiscal 1982 plan and about half of the original FY 1982 budget request of $26 million. However, there is more to these numbers than simple subtraction: Additional funding for scientific ocean drilling programs is on hold while decisions are being made about a future drilling program called Advanced Ocean Drilling (AOD).With the demise of the Ocean Margin Drilling Program (OMDP) when industry withdrew its support (Eos, October 20, 1981, p. 705) and with the Deep Sea Drilling Project (DSDP) long ago scheduled to end in fiscal 1983, the future for scientific ocean drilling within NSF was uncertain. To steer ocean drilling toward scientific objectives for the decade, the Conference on Scientific Ocean Drilling (COSOD) (Eos, December 22, 1981, p. 1197) examined four ocean drilling options and decided that the Glomar Explorer, converted to the current capabilities of the DSDP mainstay Glomar Challenger (i.e., without riser and well-control technologies), would meet scientific objectives through the decade. In December, the National Research Council's Committee on Ocean Margin Drilling came to the identical conclusion in its interim report. Both of these decisions were based solely on scientific merit and did not consider costs.

  6. Heliportable drilling in the 21. century

    Energy Technology Data Exchange (ETDEWEB)

    Argue, F. [Academy Services, Calgary, AB (Canada); Korach, D. [Nabors Alaska, Anchorage, AK (United States); Read, M. [Nabors Canada, Calgary, AB (Canada)

    2008-07-01

    The access season for conventional ice roads has been reduced. Therefore, efficient drilling programs are required for a short winter drilling, and long wells are not able to compete in one season. Heliportable drilling provides non-ice access. This presentation outlined the merits of heliportable drilling in the twenty-first century. Conventional heliportable drilling was discussed and several images of current and past heliportable drilling rigs were presented. New technologies were also illustrated and discussed, with particular reference to the Mi26T enabler, a Russian super heavy lift helicopter, leased to Airborne Energy Solutions. Operating data for the Mi26T was also presented and the heli-drill system was explained. Several twenty-first century heli-rigs were also illustrated and described, including rig 119H, rig 103AC, rig 106E, rig 99AC, and rig 105E. Last, the presentation identified the next steps for heli-rigs. tabs., figs.

  7. Drilling predation on molluscs in the northern Adriatic Sea: Spatial variability and temporal trends over the last millennia

    Science.gov (United States)

    Dengg, Markus; Wurzer, Sandra; Gallmetzer, Ivo; Haselmair, Alexandra; Zuschin, Martin

    2016-04-01

    Competition and predation are essential ecological factors influencing biodiversity. In a palaeontological context, the rate of predatory interactions between animal species is difficult to reconstruct because traces of predation are rarely incorporated into the fossil record. In the marine environment, the calcareous shells of molluscs, however, have good, long-time preservation potential, and predation in this group is often exerted by carnivorous gastropods that drill holes into mollusc shells. The prey's perforated shells remain in the sediment and can be used to study rates and intensities of predatory interactions in past marine molluscan communities. Differences in drilling frequencies along a sediment core not only reflect changes in local species richness and predation pressure, but may also mirror ecosystem changes through space and time. This makes the analysis of drilling predation an important tool when investigating the historical ecology of marine habitats. We used 1.5-m-long sediment cores from seven shelf locations spread throughout the northern Adriatic Sea basin to investigate regional and down-core variations in drilling frequencies. In total, about 54,000 bivalve and 40,000 gastropod shells were analysed to determine the following parameters: 1) overall drill frequency (DF), the proportion of shells drilled by predators; 2) edge drill frequency (EDF, only in bivalve shells), the proportion of shells with drilling traces at the shell edge; 3) multiple drill frequency (MDF), the percentage of individuals with more than one drill hole, 4) incomplete drill frequency (IDF), the percentage of shells unsuccessfully drilled; 5) prey effectiveness (PE), the proportion of individuals resisting the predator's attacks. Total drill frequency across all cores is 18% for bivalves and 13% for gastropods, but there are marked regional differences, with minima in the Po Delta (5%) and maxima in Panzano Bay (24%). Edge-drilled shells and multiple drill holes on

  8. 78 FR 63972 - Notice of Proposed Methodology for the 2014 Delaware River and Bay Water Quality Assessment Report

    Science.gov (United States)

    2013-10-25

    ... COMMISSION Notice of Proposed Methodology for the 2014 Delaware River and Bay Water Quality Assessment Report... methodology proposed to be used in the 2014 Delaware River and Bay Water Quality Assessment Report is...: Comments will be accepted via email to john.yagecic@drbc.state.nj.us , with ``Water Quality Assessment 2014...

  9. 76 FR 4716 - Commercial Leasing for Wind Power on the Outer Continental Shelf (OCS) Off Delaware, Notice of...

    Science.gov (United States)

    2011-01-26

    ... Bureau of Ocean Energy Management, Regulation and Enforcement Commercial Leasing for Wind Power on the... public notice of a proposed lease area for commercial wind development on the OCS off Delaware and... from Bluewater Wind Delaware LLC (Bluewater) and another from Occidental Development & Equities, LLC...

  10. 76 FR 50188 - Notice of Proposed Methodology for the Delaware River and Bay Integrated List Water Quality...

    Science.gov (United States)

    2011-08-12

    ... COMMISSION Notice of Proposed Methodology for the Delaware River and Bay Integrated List Water Quality... methodology proposed to be used in the 2012 Delaware River and Bay Integrated List Water Quality Assessment is... to 609-883-9522; by U.S. Mail to DRBC, Attn: Water Quality Assessment 2012, P.O. Box 7360, West...

  11. Climate Change Impacts in the State of Delaware

    Science.gov (United States)

    Snyder, C.

    2011-12-01

    The State of Delaware is currently completing its first statewide climate impacts and vulnerability assessment that will provide the foundation for a new statewide adaptation planning process. The assessment focuses on both the observed impacts and the projected impacts on five main sectors: public health and safety; infrastructure and water; industry, agriculture, and forestry; tourism and recreation; and wildlife, plants, and natural ecosystems. Examples of key impacts to the State include loss of wetlands from sea level rise and public health impacts from increased tropospheric ozone and heatwaves. The assessment is a result of collaboration across state agencies, universities, local governments, and non-governmental organizations. We discuss several challenges in translating national and regional research to locally-specific and locally-meaningful impacts necessary for the policy process, adaptation planning, and public outreach. We identify information and research gaps that continue to slow progress at the local and state level. There are lessons learned on how to best engage with policymakers and be relevant and useful for policy planning. Lastly, we give examples of successes in diverse collaborations, public communication of the results, and early policy actions resulting from the findings.

  12. Oil shale and nahcolite resources of the Piceance Basin, Colorado

    Science.gov (United States)

    ,

    2010-01-01

    This report presents an in-place assessment of the oil shale and nahcolite resources of the Green River Formation in the Piceance Basin of western Colorado. The Piceance Basin is one of three large structural and sedimentary basins that contain vast amounts of oil shale resources in the Green River Formation of Eocene age. The other two basins, the Uinta Basin of eastern Utah and westernmost Colorado, and the Greater Green River Basin of southwest Wyoming, northwestern Colorado, and northeastern Utah also contain large resources of oil shale in the Green River Formation, and these two basins will be assessed separately. Estimated in-place oil is about 1.5 trillion barrels, based on Fischer a ssay results from boreholes drilled to evaluate oil shale, making it the largest oil shale deposit in the world. The estimated in-place nahcolite resource is about 43.3 billion short tons.

  13. Centimeter-scale sedimentary sequence description of Upper Cretaceous Nenjiang Formation (lower numbers 1&2) : Lithostratigraphy, facies and cyclostratigraphy, based on the scientific drilling (SK1) borehole in the Songliao Basin.%松辽盆地松科1井上白垩统嫩江组一、二段沉积序列厘米级精细刻画:岩性·岩相·旋回

    Institute of Scientific and Technical Information of China (English)

    高有峰; 王璞珺; 程日辉; 王国栋; 万晓樵; 吴河勇; 王树学; 梁万林

    2011-01-01

    中国白垩纪大陆科学钻探松科1井连续钻取嫩江组一、二段岩心长295.53m,岩心收获率为97.45%,是迄今获取的最连续完整的沉积记录。文章对此进行了厘米级沉积地质描述(分层厚度2~5cm)。嫩江组一、二段沉积时期与晚三冬早坎潘期对应。通过对松科1井嫩江组一、二段岩心的精细描述,揭示其岩性一岩相一旋回的沉积序列及其过程。嫩江组一、二段共识别出12种岩石类型,为半深湖一深湖亚相的白云岩沉积、泥灰岩沉积、灰质泥岩沉积、油页岩沉积、浊流沉积、深湖静水泥和火山灰沉积等7种沉积微相。在岩相序列上识别出5种共213个米级旋回(六级旋回)、54个五级旋回、12个四级旋回和2个三级旋回。连续的组段厘米级刻画为高精度沉积过程研究提供了可能,嫩江纽一、二段全井段取心对松辽盆地缺氧事件、烃源岩及湖海沟通事件的研究具有重要意义。该文的精细描述资料为今后相关的深入研究提供了迄今最精准的基本地质素材。%China Cretaceous Continental Scientific Drilling (CCSD) in the Songliao Basin, called SKI project, collected 295.53 m of the lower members 1&2 of Nenjiang Formation which correspond to the late Santonian to early Campanian. The borehole got a highly continuous core section with recovery of 97. 45%, that is the most complete and precise sedimentary records up to now in the basin. Thicknesses of the description can be as thin as 2 - 5 crn for the interbedding sequences. We described the sedimentary sequence, lithology, lithofacies and cyclic stratigraphy at the drilling spot in cm-scale. Twelve litho-types were recognized in the section. Sedimentary facies are pre- dominantly lacustrine that can be subdivided into seven microfacies including dolomite, marl, argillaceous limestone, oil shale, turbidite, deep lake mudstone and volcanic ash microfacies. The whole

  14. Downhole drilling motors: technical review. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Maurer, W.C.; McDonald, W.J.; Nixon, J.D.; Matson, L.W.

    1977-08-01

    Dyna-Drills and turbodrills are used primarily for directional drilling where it is critical that the drillpipe not be rotated. These tools are not widely used for straight-hole drilling because of problems with bearing failures, low power outputs, low bit pressures, and high rotary speeds. The high rotary speeds produce bit bearing failures in 10 to 15 h, compared to 100 to 200 h life at lower rotary speeds. The technology now exists to develop reliable high-torque motors which will operate roller bits at speeds of 150 to 250 RPM and diamond bits at speeds of 400 to 800 RPM for periods of 100 to 200 hours. Sealed bearing assemblies which allow the bearings to operate in lubricant are being developed. These improved bearings allow bits to operate at the high bit weights needed for optimum drilling. Improved drilling motors can reduce drilling costs to significantly increase the number of wells drilled per drilling rig per year. Now, this is increasingly important because of the drilling rig shortage developing in this country. At least ten companies are working on the development of improved drilling motors and it is likely that several of these new motors will become commercially available within the next 2 to 3 years. Several companies are working on the development of improved high speed roller bits for use on drilling motors. The development of these high speed bits should significantly increase the use of drilling motors since bit bearing failures are a major problem when drilling with motors. The development of reliable, high-speed STRATAPAX bits should also increase motor useage since these bits drilling most effectively at rotary speeds of 300 to 500 RPM.

  15. Reducing temperature elevation of robotic bone drilling.

    Science.gov (United States)

    Feldmann, Arne; Wandel, Jasmin; Zysset, Philippe

    2016-12-01

    This research work aims at reducing temperature elevation of bone drilling. An extensive experimental study was conducted which focused on the investigation of three main measures to reduce the temperature elevation as used in industry: irrigation, interval drilling and drill bit designs. Different external irrigation rates (0 ml/min, 15 ml/min, 30 ml/min), continuously drilled interval lengths (2 mm, 1 mm, 0.5 mm) as well as two drill bit designs were tested. A custom single flute drill bit was designed with a higher rake angle and smaller chisel edge to generate less heat compared to a standard surgical drill bit. A new experimental setup was developed to measure drilling forces and torques as well as the 2D temperature field at any depth using a high resolution thermal camera. The results show that external irrigation is a main factor to reduce temperature elevation due not primarily to its effect on cooling but rather due to the prevention of drill bit clogging. During drilling, the build up of bone material in the drill bit flutes result in excessive temperatures due to an increase in thrust forces and torques. Drilling in intervals allows the removal of bone chips and cleaning of flutes when the drill bit is extracted as well as cooling of the bone in-between intervals which limits the accumulation of heat. However, reducing the length of the drilled interval was found only to be beneficial for temperature reduction using the newly designed drill bit due to the improved cutting geometry. To evaluate possible tissue damage caused by the generated heat increase, cumulative equivalent minutes (CEM43) were calculated and it was found that the combination of small interval length (0.5 mm), high irrigation rate (30 ml/min) and the newly designed drill bit was the only parameter combination which allowed drilling below the time-thermal threshold for tissue damage. In conclusion, an optimized drilling method has been found which might also enable drilling in more

  16. Device for purifying drilling mud

    Energy Technology Data Exchange (ETDEWEB)

    Surkov, V.T.; Dorosh, M.M.; Khariv, I.Yu.; Makedonov, N.I.

    1982-01-01

    A device is proposed for purifying drilling mud which includes a dynamic filter made in the form of a spiral-shaped tube with input and output sleeves, and a container for purified solution with outlet sleeve. It is distinguished by the fact that in order to simplify the design, the spiral-shaped tube is perforated from the inside and is installed in the container for the purified solution.

  17. AURORA BOREALIS - European Research Icebreaker With Drilling Capability

    Science.gov (United States)

    Biebow, N.; Lembke-Jene, L.; Kunz-Pirrung, M.; Thiede, J.

    2008-12-01

    The polar oceans are the least known areas of the globe, in although they hold the key to many of our climate´s secrets. How does the sea ice coverage and the sea water properties change? How do plants and animals survive under the most extreme conditions of the earth? Which information of past climate change can be read from the sediments at the sea-floor and how can the future changing climate be predicted? In order to answer such and further questions, for the moment a hypermodern research vessel, the AURORA BOREALIS, is planned, which can handle the cool summers and freezing winters of the polar oceans and which can drill deep into the sea floor. AURORA BOREALIS will be the most advanced Research Icebreaker in the world with a multi-functional role of drilling in deep ocean basins and supporting climate/environmental research and decision support for stakeholder governments for the next 35-40 years. It will have a high icebreaking capacity to penetrate autonomously (single ship operation) into the central Arctic Ocean with more than 2.5 meters of ice cover, during all seasons of the year. The new technological features will include dynamic positioning in closed sea- ice cover, satellite navigation and ice-management support and the deployment and operation of Remotely Operated Vehicles (ROV) and Autonomous Underwater Vehicles (AUVs) from the twin moon-pools. A unique feature of the vessel is the deep-sea drilling rig, which will enable sampling of the ocean floor and sub-sea up to 5000 m water and 1000 m penetration at the most inhospitable places on earth. The drilling capability will be deployed in both Polar Regions on the long run and AURORA BOREALIS will be the only vessel worldwide that could undertake this type of scientific investigation.

  18. Modeling of Drilling Forces Based on Twist Drill Point Angles Using Multigene Genetic Programming

    Directory of Open Access Journals (Sweden)

    Myong-Il Kim

    2016-01-01

    Full Text Available The mathematical model was developed for predicting the influence of the drill point angles on the cutting forces in drilling with the twist drills, which was used to optimize those angles for reducing drilling forces. The approach was based on multigene genetic programming, for the training data, the grinding tests of twist drill were firstly conducted for the different drill point angles in Biglide parallel machine, and then drilling tests were performed on carbon fiber reinforced plastics using the grinded drills. The effectiveness of the proposed approach was verified through comparing with published data. It was found that the proposed model agreed well with the experimental data and was useful for improving the performance of twist drill.

  19. Automatic detection of reservoir influx in conventional drilling, managed pressure drilling and dual gradient drilling

    OpenAIRE

    Pettersen, Sigmund

    2012-01-01

    Reservoir influxes, or kicks, are well control incidents with the potential of severe consequences to health, safety and the environment, as well as economics. Although the main focus will always be to prevent such incidents from happening, drilling crew will also need to be able to spot reservoir influx as quickly as possible. This thesis presents a method for automated detection of reservoir influx or losses based on simulations of the surface circulation system. Theoretical background...

  20. Methods to ensure optimal off-bottom and drill bit distance under pellet impact drilling

    Science.gov (United States)

    Kovalyov, A. V.; Isaev, Ye D.; Vagapov, A. R.; Urnish, V. V.; Ulyanova, O. S.

    2016-09-01

    The paper describes pellet impact drilling which could be used to increase the drilling speed and the rate of penetration when drilling hard rock for various purposes. Pellet impact drilling implies rock destruction by metal pellets with high kinetic energy in the immediate vicinity of the earth formation encountered. The pellets are circulated in the bottom hole by a high velocity fluid jet, which is the principle component of the ejector pellet impact drill bit. The paper presents the survey of methods ensuring an optimal off-bottom and a drill bit distance. The analysis of methods shows that the issue is topical and requires further research.

  1. New optimized drill pipe size for deep-water, extended reach and ultra-deep drilling

    Energy Technology Data Exchange (ETDEWEB)

    Jellison, Michael J.; Delgado, Ivanni [Grant Prideco, Inc., Hoston, TX (United States); Falcao, Jose Luiz; Sato, Ademar Takashi [PETROBRAS, Rio de Janeiro, RJ (Brazil); Moura, Carlos Amsler [Comercial Perfuradora Delba Baiana Ltda., Rio de Janeiro, RJ (Brazil)

    2004-07-01

    A new drill pipe size, 5-7/8 in. OD, represents enabling technology for Extended Reach Drilling (ERD), deep water and other deep well applications. Most world-class ERD and deep water wells have traditionally been drilled with 5-1/2 in. drill pipe or a combination of 6-5/8 in. and 5-1/2 in. drill pipe. The hydraulic performance of 5-1/2 in. drill pipe can be a major limitation in substantial ERD and deep water wells resulting in poor cuttings removal, slower penetration rates, diminished control over well trajectory and more tendency for drill pipe sticking. The 5-7/8 in. drill pipe provides a significant improvement in hydraulic efficiency compared to 5-1/2 in. drill pipe and does not suffer from the disadvantages associated with use of 6-5/8 in. drill pipe. It represents a drill pipe assembly that is optimized dimensionally and on a performance basis for casing and bit programs that are commonly used for ERD, deep water and ultra-deep wells. The paper discusses the engineering philosophy behind 5-7/8 in. drill pipe, the design challenges associated with development of the product and reviews the features and capabilities of the second-generation double-shoulder connection. The paper provides drilling case history information on significant projects where the pipe has been used and details results achieved with the pipe. (author)

  2. Matemáticas de Infantil en Delaware, USA

    Directory of Open Access Journals (Sweden)

    Judith Fábrega

    2013-07-01

    Full Text Available Estados Unidos se encuentra en momento de cambio en el sistema educativo. La implantación de los estándares comunes para todas las etapas de educación obligatoria proporciona una estructura normalizada para todo el territorio estadounidense. En este documento, se presenta un ejemplo de cómo trabajar los estándares matemáticos en una clase bilingüe de alumnos de 5 a 6 años. La implementación difiere de estado a estado. En este caso concreto se sigue un currículo bastante estricto, con un material pautado y guías del profesor. No obstante, el maestro/a siempre puede complementar este currículo con otros talleres y juegos matemáticos. Arte, juegos de mesa y actividades motrices, entre otros, ayudan a los alumnos/as a entender y, lo más importante, a aplicar las capacidades matemáticas trabajadas.Mathematics in a Kindergarten School in Delaware, USA. The education system in United States of America is undergoing significant changes. The implementation of the new Common Core Standards in K - 12 provides for a unified structure for the entire territory. This article presents examples of how to work those new standards for mathematics in a bilingual kindergarten classroom.The implementation differs from State to State. In this specific case we follow a very strict curriculum, which includes learning materials and teacher guides. Nevertheless, teachers can always complement the curriculum with any other mathematic workshops and games. Art, board games and motor activities, among others, can help students understand - and more importantly - to apply the mathematic skills learned.

  3. The Need for Scientific Ocean Drilling

    Science.gov (United States)

    Humphris, Susan E.; deMenocal, Peter B.; Edwards, Katrina J.; Fisher, Andrew T.; Saffer, Demian

    2011-03-01

    Mark Twain once said, “I was seldom able to see an opportunity until it had ceased to be one.” The scientific community could soon miss an opportunity in ocean drilling. A recent article in Eos by D. K. Smith et al. (Ocean drilling: Forty years of international collaboration, Eos, 91(43), 393-394, 2010) summarized the history of scientific ocean drilling and presented an overview of the Integrated Ocean Drilling Program (IODP) as it currently operates. IODP will end in 2013, and an ambitious science plan is being developed to launch a new drilling program. Some people have asked, Given the program's past successes, why do we need more scientific ocean drilling?

  4. Advanced Seismic While Drilling System

    Energy Technology Data Exchange (ETDEWEB)

    Robert Radtke; John Fontenot; David Glowka; Robert Stokes; Jeffery Sutherland; Ron Evans; Jim Musser

    2008-06-30

    A breakthrough has been discovered for controlling seismic sources to generate selectable low frequencies. Conventional seismic sources, including sparkers, rotary mechanical, hydraulic, air guns, and explosives, by their very nature produce high-frequencies. This is counter to the need for long signal transmission through rock. The patent pending SeismicPULSER{trademark} methodology has been developed for controlling otherwise high-frequency seismic sources to generate selectable low-frequency peak spectra applicable to many seismic applications. Specifically, we have demonstrated the application of a low-frequency sparker source which can be incorporated into a drill bit for Drill Bit Seismic While Drilling (SWD). To create the methodology of a controllable low-frequency sparker seismic source, it was necessary to learn how to maximize sparker efficiencies to couple to, and transmit through, rock with the study of sparker designs and mechanisms for (a) coupling the sparker-generated gas bubble expansion and contraction to the rock, (b) the effects of fluid properties and dynamics, (c) linear and non-linear acoustics, and (d) imparted force directionality. After extensive seismic modeling, the design of high-efficiency sparkers, laboratory high frequency sparker testing, and field tests were performed at the University of Texas Devine seismic test site. The conclusion of the field test was that extremely high power levels would be required to have the range required for deep, 15,000+ ft, high-temperature, high-pressure (HTHP) wells. Thereafter, more modeling and laboratory testing led to the discovery of a method to control a sparker that could generate low frequencies required for deep wells. The low frequency sparker was successfully tested at the Department of Energy Rocky Mountain Oilfield Test Center (DOE RMOTC) field test site in Casper, Wyoming. An 8-in diameter by 26-ft long SeismicPULSER{trademark} drill string tool was designed and manufactured by TII

  5. Gas reservoir evaluation for underbalanced horizontal drilling

    Directory of Open Access Journals (Sweden)

    Li Gao

    2014-01-01

    Full Text Available A set of surface equipment for monitoring the parameters of fluid and pressure while drilling was developed, and mathematical models for gas reservoir seepage and wellbore two-phase flow were established. Based on drilling operation parameters, well structure and monitored parameters, the wellbore pressure and the gas reservoir permeability could be predicted theoretically for underbalanced horizontal drilling. Based on the monitored gas production along the well depth, the gas reservoir type could be identified.

  6. Reliability-Growth of Triplex Drilling Pump

    Institute of Scientific and Technical Information of China (English)

    Hou Yu; ZhaoZhong

    1996-01-01

    @@ Introduction to triplex pump The triplex pump widely used in oilfields is composed of power end assembly, fluid end assembly, piston-liner spraying system, lubrication system and charging system.The pump delivers mud into oil well. Through nozzles of drilling bit, the mud inside the drilling shaft comes to the annular space between drilling shaft and casing string and then returns to surface.

  7. Data analytics for drilling operational states classifications

    OpenAIRE

    Veres, Galina; Sabeur, Zoheir

    2015-01-01

    This paper provides benchmarks for the identification of best performance classifiers for the detection of operational states in industrial drilling operations. Multiple scenarios for the detection of the operational states are tested on a rig with various drilling wells. Drilling data are extremely challenging due to their non-linear and stochastic natures, notwithstanding the embedded noise in them and unbalancing. Nevertheless, there is a possibility to deploy robust classifiers to overcom...

  8. General Considerations for Drill System Design

    Science.gov (United States)

    1975-06-01

    meltwater can bu absorbed and refrozen in the adjacent snow. A similar principle has been suggested for disposal of melted rock produced by thermal...This last item can become very serious if the drill is immersed in meltwater . Ileat losses at the drill head are not easy to estimate in simple...Phlslberth, K. (in pr is) The thermal probe deep drilling method by E016 in 1968 at Station jul-Joaet. Central Greenland , Proceedings of icr Core

  9. Advanced Seismic While Drilling System

    Energy Technology Data Exchange (ETDEWEB)

    Robert Radtke; John Fontenot; David Glowka; Robert Stokes; Jeffery Sutherland; Ron Evans; Jim Musser

    2008-06-30

    A breakthrough has been discovered for controlling seismic sources to generate selectable low frequencies. Conventional seismic sources, including sparkers, rotary mechanical, hydraulic, air guns, and explosives, by their very nature produce high-frequencies. This is counter to the need for long signal transmission through rock. The patent pending SeismicPULSER{trademark} methodology has been developed for controlling otherwise high-frequency seismic sources to generate selectable low-frequency peak spectra applicable to many seismic applications. Specifically, we have demonstrated the application of a low-frequency sparker source which can be incorporated into a drill bit for Drill Bit Seismic While Drilling (SWD). To create the methodology of a controllable low-frequency sparker seismic source, it was necessary to learn how to maximize sparker efficiencies to couple to, and transmit through, rock with the study of sparker designs and mechanisms for (a) coupling the sparker-generated gas bubble expansion and contraction to the rock, (b) the effects of fluid properties and dynamics, (c) linear and non-linear acoustics, and (d) imparted force directionality. After extensive seismic modeling, the design of high-efficiency sparkers, laboratory high frequency sparker testing, and field tests were performed at the University of Texas Devine seismic test site. The conclusion of the field test was that extremely high power levels would be required to have the range required for deep, 15,000+ ft, high-temperature, high-pressure (HTHP) wells. Thereafter, more modeling and laboratory testing led to the discovery of a method to control a sparker that could generate low frequencies required for deep wells. The low frequency sparker was successfully tested at the Department of Energy Rocky Mountain Oilfield Test Center (DOE RMOTC) field test site in Casper, Wyoming. An 8-in diameter by 26-ft long SeismicPULSER{trademark} drill string tool was designed and manufactured by TII

  10. Approved Applications for Permit to Drill - Not Drilled: As of Sept. 30, 2011

    Data.gov (United States)

    Bureau of Land Management, Department of the Interior — This table contains the total number of applications for permit to drill (APDs) by state that had not been drilled as of Sept. 30, 2011. Oil and gas operators may...

  11. Deep Drilling Results in the Atlantic Ocean: Continental Margins and Paleoenvironment

    Science.gov (United States)

    1979-01-01

    volcanic hydrothermal exhalations. Bemuda Ri -For tiii-pc ds approximately However, the formation at most sites is not- near to- the seli~t traisiti -nfroi...A.C., et al., Initial Re- Greenwood, R., Cristobalite : its relationship to Gse ports Deep Sea Drilling Project, 14, 787-954 chert formation in...Ryan ; , l l l l l4 CONTENTS Preface " Mesozoic-Cerozoic Sedimentary Formations of the North American Basin. Western North Atlantic, L. F. Jansa, P. Enos

  12. IMPACT OF DRILLING WASTE ON HYDROBIONTS

    Directory of Open Access Journals (Sweden)

    S. A. Guseinova

    2015-01-01

    Full Text Available Aim. The aim is to determine and make an analysis of the concentration of petroleum hydrocarbons and other metals in the waste drilling: drill cuttings (DC and mud (DM, collected in the area of drilling, to assess and forecast the state of biological resources of natural sea water.Methods. Experimental studies of DC and DM showed the petroleum hydrocarbons content, the concentration of which varies depending on the timing of exposure. By quantitative and qualitative indicators, the metal content in the drill cuttings and mud is nonequivalent and this depends on the structure and hardness achieved during drilling the rocks as well as on the degree of contamination with metals.Results. The concentration level of petroleum hydrocarbons and other metals in the drilling waste (drill cuttings and mud imposes a major problem associated with the conservation of biological resources of the Caspian Sea.Main conclusions. Environmental effects from the discharges of drilling waste on the high seas can be detected only during drilling operations and in close proximity (typically up to 200-500 m from the discharge point. Persistent damages in communities and ecosystems occur only at long exposures and are adaptive in nature.

  13. Steerable system adds precision to Gulf drilling

    Energy Technology Data Exchange (ETDEWEB)

    Bierschwale, H.; Ridley, R.

    1988-05-02

    A well bore intersection was achieved ahead of schedule with a steerable drilling system in the Gulf of Mexico. A computer-generated proximity survey comparing the directional surveys of the initial and replacement wells, confirmed that the wells were within 1 ft. of each other near the planned intersection depth of 8,890 ft. All objectives for the 9,050-ft. replacement well were accomplished 4 days ahead of schedule. This operation illustrates the effectiveness of the steerable drilling system for obtaining better directional control, increased drilling efficiently, and reduced overall drilling time. This article explains how the project was completed.

  14. Vale exploratory slimhole: Drilling and testing

    Energy Technology Data Exchange (ETDEWEB)

    Finger, J.T.; Jacobson, R.D.; Hickox, C.E.

    1996-06-01

    During April-May, 1995, Sandia National Laboratories, in cooperation with Trans-Pacific Geothermal Corporation, drilled a 5825{prime} exploratory slimhole (3.85 in. diameter) in the Vale Known Geothermal Resource Area (KGRA) near Vale, Oregon. This well was part of Sandia`s program to evaluate slimholes as a geothermal exploration tool. During drilling we performed several temperature logs, and after drilling was complete we performed injection tests, bailing from a zone isolated by a packer, and repeated temperature logs. In addition to these measurements, the well`s data set includes: 2714{prime} of continuous core (with detailed log); daily drilling reports from Sandia and from drilling contractor personnel; daily drilling fluid records; numerous temperature logs; pressure shut-in data from injection tests; and comparative data from other wells drilled in the Vale KGRA. This report contains: (1) a narrative account of the drilling and testing, (2) a description of equipment used, (3) a brief geologic description of the formation drilled, (4) a summary and preliminary interpretation of the data, and (5) recommendations for future work.

  15. Drilling of polymer-matrix composites

    CERN Document Server

    Krishnaraj, Vijayan; Davim, J Paulo

    2013-01-01

    Polymeric composites are recognised as good candidates for structural components due to their inherent properties. However, they present several kinds of damages while creating holes for assembly. Delamination is considered the most serious damage since it reduces service life of the component. Thrust and delamination can be controlled by proper drill point geometry. Drilling at high speed is also a current requirement of the aerospace industry. This book focus on drilling of polymer matrix composites for aerospace and defence applications. The book presents introduction to machining of polymer composites and discusses drilling as a processing of composites.

  16. Optimization of Orthopaedic Drilling: A Taguchi Approach

    Directory of Open Access Journals (Sweden)

    Rupesh Kumar Pandey

    2012-06-01

    Full Text Available Bone drilling is a common procedure to prepare an implant site during orthopaedic surgery. An increase in temperature during such a procedure can result in thermal ostenecrosis which may delay healing or reduce the stability of the fixation. Therefore it is important to minimize the thermal invasion of bone during drilling. The Taguchi method has been applied to investigate the optimal combination of drill diameter, feed rate and spindle speed in dry drilling of Polymethylmethacrylate (PMMA for minimizing the temperature produced.

  17. Newberry exploratory slimhole: Drilling and testing

    Energy Technology Data Exchange (ETDEWEB)

    Finger, J.T.; Jacobson, R.D.; Hickox, C.E.

    1997-11-01

    During July--November, 1995, Sandia National Laboratories, in cooperation with CE Exploration, drilled a 5,360 feet exploratory slimhole (3.895 inch diameter) in the Newberry Known Geothermal Resource Area (KGRA) near Bend, Oregon. This well was part of Sandia`s program to evaluate slimholes as a geothermal exploration tool. During and after drilling the authors performed numerous temperature logs, and at the completion of drilling attempted to perform injection tests. In addition to these measurements, the well`s data set includes: over 4,000 feet of continuous core (with detailed log); daily drilling reports from Sandia and from drilling contractor personnel; daily drilling fluid record; and comparative data from other wells drilled in the Newberry KGRA. This report contains: (1) a narrative account of the drilling and testing, (2) a description of equipment used, (3) a brief geologic description of the formation drilled, (4) a summary and preliminary interpretation of the data, and (5) recommendations for future work.

  18. Concentrations and transport of atrazine in the Delaware River-Perry Lake system, northeast Kansas, July 1993 through September 1995

    Science.gov (United States)

    Pope, L.M.; Brewer, L.D.; Foley, G.A.; Morgan, S.C.

    1996-01-01

    A study of the distribution and transport of atrazine in surface water in the 1,117 square-mile Delaware River Basin in northeast Kansas was conducted from July 1992 through September 1995. The purpose of this report is to present information to assess the present (1992-95) conditions and possible future changes in the distribution and magnitude of atrazine concentrations, loads, and yields spatially, temporally, and in relation to hydrologic conditions and land-use characteristics. A network of 11 stream-monitoring and sample-collection sites was established within the basin. Stream- water samples were collected during a wide range of hydrologic conditions throughout the study. Nearly 5,000 samples were analyzed by enzyme- linked immunosorbent assay (ELISA) for triazine herbicide concentrations. Daily mean triazine herbicide concentrations were calculated for all sampling sites and subsequently used to estimate daily mean atrazine concentrations with a linear- regression relation between ELISA-derived triazine concentrations and atrazine concentrations determined by gas chromatography/mass spectrometry for 141 dual-analyzed surface-water samples. During May, June, and July, time-weighted, daily mean atrazine concentrations in streams in the Delaware River Basin commonly exceeded the value of 3.0-ug/L (micrograms per liter) annual mean Maximum Contaminant Level (MCL) established by the U.S. Environmental Protection Agency for drinking-water supplies. Time-weighted, daily mean concentrations equal to or greater than 20 ug/L were not uncommon. However, most time- weighted, daily mean concentrations were less than 1.0 ug/L from August through April. The largest time-weighted, monthly mean atrazine concentrations occurred during May, June, and July. Most monthly mean concentrations between August and April were less than 0.50 ug/L. Large differences were documented in monthly mean concentrations within the basin. Sites receiving runoff from the northern and

  19. Environmental Measurement-While-Drilling System and Horizontal Directional Drilling Technology Demonstration, Hanford Site

    Energy Technology Data Exchange (ETDEWEB)

    Williams, C.V.; Lockwood, G.J.; Normann, R.A.; Myers, D.A.; Gardner, M.G.; Williamson, T.; Huffman, J.

    1999-06-01

    The Environmental Measurement-While-Drilling (EMWD) system and Horizontal Directional Drilling (HDD) were successfully demonstrated at the Mock Tank Leak Simulation Site and the Drilling Technology Test Site, Hanford, Washington. The use of directional drilling offers an alternative to vertical drilling site characterization. Directional drilling can develop a borehole under a structure, such as a waste tank, from an angled entry and leveling off to horizontal at the desired depth. The EMWD system represents an innovative blend of new and existing technology that provides the capability of producing real-time environmental and drill bit data during drilling operations. The technology demonstration consisted of the development of one borehole under a mock waste tank at a depth of {approximately} {minus}8 m ({minus}27 ft.), following a predetermined drill path, tracking the drill path to within a radius of {approximately}1.5 m (5 ft.), and monitoring for zones of radiological activity using the EMWD system. The purpose of the second borehole was to demonstrate the capability of drilling to a depth of {approximately} {minus}21 m ({minus}70 ft.), the depth needed to obtain access under the Hanford waste tanks, and continue drilling horizontally. This report presents information on the HDD and EMWD technologies, demonstration design, results of the demonstrations, and lessons learned.

  20. Kinematic equations to grind a helical drill point on a virtual axis drill sharpener

    Institute of Scientific and Technical Information of China (English)

    陈五一; 陈鼎昌

    2000-01-01

    The basic structure of a virtual axis drill grinder is presented in terms of the spatial vectors and thegrinding parameters calculated according to the geometry of a helical drill point. The kinematic equations for sharpening the drills on the virtual axis grinder are deduced using the grinding parameters via vector-matrix txansformation.

  1. Biological treatment of drilling waste

    Energy Technology Data Exchange (ETDEWEB)

    Perie, F.H.; Seris, J.L.; Martignon, A.P.

    1995-12-01

    Off shore operators are now faced with more stringent forthcoming regulations regarding waste discharge. Several aspects are to be taken into account when considering waste disposal in the sea; among them, the total amount of COD and the toxicity. While, in many regards, the problem caused by the processing fluids toxicity has been addressed, the elimination of residual COD from the waste is yet to be solved. Biodegradation of drilling waste is one of the major routes taken by third party contracters to address the reduction of COD in sea-discharged cuttings. This report describes a technique specifically developed to enhance drilling waste biodegradation under selected conditions. The suggested treatment involved biological catalysts used in conjunction with or prior to the biodegradation. We demonstrated that the considered environment-compatible substitute for oil-based mud could be more efficiently biodegraded if an enzymatic pretreatment was carried out prior to or during the actual biodegradation. The biodegradation rate, expressed as CO{sub 2} envolvement, was significantly higher in lipase-treated cultures. In addition, we demonstrated that this treatment was applicable to substrates in emulsion, suspension, or adsorbed on solid.

  2. HIGH-POWER TURBODRILL AND DRILL BIT FOR DRILLING WITH COILED TUBING

    Energy Technology Data Exchange (ETDEWEB)

    Robert Radtke; David Glowka; Man Mohan Rai; David Conroy; Tim Beaton; Rocky Seale; Joseph Hanna; Smith Neyrfor; Homer Robertson

    2008-03-31

    Commercial introduction of Microhole Technology to the gas and oil drilling industry requires an effective downhole drive mechanism which operates efficiently at relatively high RPM and low bit weight for delivering efficient power to the special high RPM drill bit for ensuring both high penetration rate and long bit life. This project entails developing and testing a more efficient 2-7/8 in. diameter Turbodrill and a novel 4-1/8 in. diameter drill bit for drilling with coiled tubing. The high-power Turbodrill were developed to deliver efficient power, and the more durable drill bit employed high-temperature cutters that can more effectively drill hard and abrasive rock. This project teams Schlumberger Smith Neyrfor and Smith Bits, and NASA AMES Research Center with Technology International, Inc (TII), to deliver a downhole, hydraulically-driven power unit, matched with a custom drill bit designed to drill 4-1/8 in. boreholes with a purpose-built coiled tubing rig. The U.S. Department of Energy National Energy Technology Laboratory has funded Technology International Inc. Houston, Texas to develop a higher power Turbodrill and drill bit for use in drilling with a coiled tubing unit. This project entails developing and testing an effective downhole drive mechanism and a novel drill bit for drilling 'microholes' with coiled tubing. The new higher power Turbodrill is shorter, delivers power more efficiently, operates at relatively high revolutions per minute, and requires low weight on bit. The more durable thermally stable diamond drill bit employs high-temperature TSP (thermally stable) diamond cutters that can more effectively drill hard and abrasive rock. Expectations are that widespread adoption of microhole technology could spawn a wave of 'infill development' drilling of wells spaced between existing wells, which could tap potentially billions of barrels of bypassed oil at shallow depths in mature producing areas. At the same time, microhole

  3. BIOREMEDIATION OF AN EXPERIMENTAL OIL SPILL ON THE SHORELINE OF DELAWARE BAY

    Science.gov (United States)

    In the summer of 1994, a field study was undertaken in Delaware in which light crude oil was intentionally released onto plots to evaluate bioremediation. The objectives were to obtain credible statistical evidence to determine if bioremediation with inorganic mineral nutrients ...

  4. 77 FR 28489 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the...

    Science.gov (United States)

    2012-05-15

    ... to the Control of Nitrogen Oxides Emissions From Industrial Boilers and Process Heaters at Petroleum... Delaware's regulation that establishes controls for nitrogen oxides (NO X ) emissions from industrial... amend the regulation that establishes controls for NO X emissions from industrial boilers and...

  5. 77 FR 3211 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the...

    Science.gov (United States)

    2012-01-23

    ... Control of Nitrogen Oxides Emissions From Industrial Boilers and Process Heaters at Petroleum Refineries... amends Delaware's regulation that establishes controls for nitrogen oxides (NO X ) emissions from industrial boilers and process heaters at petroleum refineries by including a NO X emission limit for...

  6. 77 FR 22224 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Amendments to the...

    Science.gov (United States)

    2012-04-13

    ... revision amends the control of volatile organic compound (VOC) emissions from industrial cleaning solvents... meet the requirements to implement reasonably available control technology (RACT) controls on emission... developments and expand VOC emission controls. The revision is part of Delaware's strategy to achieve...

  7. 78 FR 39601 - Safety Zone, Sugar House Casino Fireworks Display, Delaware River; Philadelphia, PA

    Science.gov (United States)

    2013-07-02

    ... SECURITY Coast Guard 33 CFR Part 165 RIN 1625-AA00 Safety Zone, Sugar House Casino Fireworks Display... out zone that covers part of the Delaware River. Sugar House Casino has contracted with Pyrotecnico... Sugar House Casino Fireworks Display will pose significant risks to the public. The purpose of the...

  8. Monitoring hemlock crown health in Delaware Water Gap National Recreation Area

    Science.gov (United States)

    Michael E. Montgomery; Bradley Onken; Richard A. Evans; Richard A. Evans

    2005-01-01

    Decline of the health of hemlocks in Delaware Water Gap National Recreation Area was noticeable in the southern areas of the park by 1992. The following year, a series of plots were established to monitor hemlock health and the abundance of hemlock woolly adelgid. This poster examines only the health rating of the hemlocks in the monitoring plots.

  9. TOXICITY TRENDS DURING AN OIL SPILL BIOREMEDIATION EXPERIMENT ON A SANDY SHORELINE IN DELAWARE, USA

    Science.gov (United States)

    A 13-week, refereed, inter-agency toxicity testing program involving five bioassay methods was used to document the effectiveness of shoreline bioremediation to accelerate toxicity reduction of an oiled sandy shoreline at Fowler Beach, Delaware, USA. The study was part of an inte...

  10. 76 FR 20367 - Commercial Leasing for Wind Power on the Outer Continental Shelf (OCS) Off Delaware...

    Science.gov (United States)

    2011-04-12

    ... Bureau of Ocean Energy Management, Regulation and Enforcement Commercial Leasing for Wind Power on the... notice provides BOEMRE's determination that no competitive interest exists in acquiring a commercial wind... 21653). Bluewater Wind Delaware, LLC submitted the only valid expression of commercial interest in...

  11. Delaware Stars for Early Success. QRS Profile. The Child Care Quality Rating System (QRS) Assessment

    Science.gov (United States)

    Child Trends, 2010

    2010-01-01

    This paper presents a profile of Delaware's Stars for Early Success prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators…

  12. Case-control study of tobacco smoke exposure and breast cancer risk in Delaware

    Directory of Open Access Journals (Sweden)

    Hathcock H Leroy

    2008-06-01

    Full Text Available Abstract Background Tobacco smoke exposure may be associated with increased breast cancer risk, although the evidence supporting the association is inconclusive. We conducted a case-control study in Delaware, incorporating detailed exposure assessment for active and secondhand smoke at home and in the workplace. Methods Primary invasive breast cancer cases diagnosed among female Delaware residents, ages 40–79, in 2000–2002 were identified through the Delaware cancer registry (n = 287. Delaware drivers license and Health Care Finance Administration records were used to select age frequency-matched controls for women Results A statistically significant increased risk of breast cancer was observed for ever having smoked cigarettes (odds ratio = 1.43, 95% confidence interval = 1.03–1.99. However, there was no evidence of a dose-response relationship between breast cancer risk and total years smoked, cigarettes per day, or pack-years. Neither residential nor workplace secondhand smoke exposure was associated with breast cancer. Recalculations of active smoking risks using a purely unexposed reference group of women who were not exposed to active or secondhand smoking did not indicate increased risks of breast cancer. Conclusion These findings do not support an association between smoking and breast cancer.

  13. The Politics of Race and Educational Disparities in Delaware's Public Schools

    Science.gov (United States)

    Davis, Theodore J., Jr.

    2017-01-01

    Delaware has long played a pivotal role in the nation's struggle to end school segregation and promote educational equality. This article discusses racial disparities in educational achievement and outcomes by examining the state's political history and the politics of race in public education. This article explores educational disparities from a…

  14. Improving Anti-Rape Policy and Education at the University of Delaware

    Science.gov (United States)

    Schiffman, Jessica

    2010-01-01

    It is incumbent on colleges and universities to evaluate the conditions that lead to sexual assault on their campuses and to address those that may support a climate that encourages or tolerates rape. Though various policies and educational programs attempt to mitigate the problem, still it persists. The University of Delaware has not engaged in a…

  15. 78 FR 57573 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Attainment Plan for the...

    Science.gov (United States)

    2013-09-19

    ... expeditiously as practicable in a given area.\\21\\ Thus, assuming no presumptions under 40 CFR 51.1002, a state... in a given nonattainment area.\\35\\ \\34\\ See 40 CFR 51.1008. \\35\\ See 2007 PM 2.5 Implementation Rule... Plan for the Philadelphia-Wilmington, Pennsylvania-New Jersey-Delaware Nonattainment Area for the...

  16. State of Delaware Science Curriculum Framework Content Standards [and] Performance Indicators, 6-8.

    Science.gov (United States)

    Delaware State Dept. of Education, Dover.

    Part of the Delaware Department of Education's ongoing efforts to provide assistance and support to local school districts in their development of a standards-based curriculum, this document presents the eight science standards for middle school. The standards for grades 6-8 are: (1) nature and application of science and technology; (2) materials…

  17. 77 FR 58953 - Approval and Promulgation of Air Quality Implementation Plans; Delaware; Control Technique...

    Science.gov (United States)

    2012-09-25

    ... AGENCY 40 CFR Part 52 Approval and Promulgation of Air Quality Implementation Plans; Delaware; Control... published in the Federal Register. This action is not a ``major rule'' as defined by 5 U.S.C. 804(2). C... compounds. Dated: September 7, 2012. Shawn M. Garvin, Regional Administrator, Region III. 40 CFR part 52...

  18. Environmental Assessment. Increase Fuel Storage Capacity, Dover Air Force Base, Delaware

    Science.gov (United States)

    2012-06-01

    in 1998. Grasshopper Sparrow 2 Observed on Bergold Farm 16 July 2003 and in 1998. Great blue heron 2 Observed many times foraging along both Pipe...ENVIRONMENTAL CONSEQUENCES Increase Fuels Capacity Dover Air Force Base, Delaware 28 calculations were derived from the same EPA software utilized to

  19. Synopsis of the University of Delaware's Office of Computer-Based Instruction.

    Science.gov (United States)

    Hofstetter, Fred T.

    This brief paper presents background information and a description of the organizational structure and educational objectives of the Office of Computer-Based Instruction, formerly the Delaware PLATO project, whose name was changed to reflect the University's ongoing commitment to providing leadership in educational computing following the…

  20. Oil Resources Potential and Exploration of Ordos Basin

    Institute of Scientific and Technical Information of China (English)

    Yang Hua; Luo Anxiang; Fu Jinhua; Xi Shengli

    2007-01-01

    @@ Ordos Basin has experienced nearly a century of oil-gas exploration since China's first oil exploratory well (Yan-1 well) was drilled in 1907 in Yanchang County, Shaanxi Province. A good prospect for sustained and steady development of oil and gas was thereby opened based on the efforts made by generations of petroleum geologists and oil workers.

  1. Laser Drilling - Drilling with the Power of Light

    Energy Technology Data Exchange (ETDEWEB)

    Iraj A. Salehi; Brian C. Gahan; Samih Batarseh

    2007-02-28

    Gas Technology Institute (GTI) has been the leading investigator in the field of high power laser applications research for well construction and completion applications. Since 1997, GTI (then as Gas Research Institute- GRI) has investigated several military and industrial laser systems and their ability to cut and drill into reservoir type rocks. In this report, GTI continues its investigation with a 5.34 kW ytterbium-doped multi-clad high power fiber laser (HPFL). When compared to its competitors; the HPFL represents a technology that is more cost effective to operate, capable of remote operations, and requires considerably less maintenance and repair. Work performed under this contract included design and implementation of laboratory experiments to investigate the effects of high power laser energy on a variety of rock types. All previous laser/rock interaction tests were performed on samples in the lab at atmospheric pressure. To determine the effect of downhole pressure conditions, a sophisticated tri-axial cell was designed and tested. For the first time, Berea sandstone, limestone and clad core samples were lased under various combinations of confining, axial and pore pressures. Composite core samples consisted of steel cemented to rock in an effort to represent material penetrated in a cased hole. The results of this experiment will assist in the development of a downhole laser perforation or side tracking prototype tool. To determine how this promising laser would perform under high pressure in-situ conditions, GTI performed a number of experiments with results directly comparable to previous data. Experiments were designed to investigate the effect of laser input parameters on representative reservoir rock types of sandstone and limestone. The focus of the experiments was on laser/rock interaction under confining pressure as would be the case for all drilling and completion operations. As such, the results would be applicable to drilling, perforation, and

  2. Measurement-While-Drilling (MWD) development for air drilling

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, W.A.; Rubin, L.A.

    1993-12-31

    When downhole contact between the BHA and formation was optimum, as it was during rotation, high signal levels were experienced. Survey data acquired at the connections, when the BHA was totally at rest, is excellent. GEC intends modifying the system to optimize operations consistent with these disparate factors. A Mean-Time-To-Failure (MTTF) of 89.9 hours appears reasonable from the data. It is not possible to infer an MTBF figure from this test. It is quite obvious, however, that the system reliability performance has been significantly improved since FT {number_sign}5 was performed almost two years earlier. Based on the above results, GEC concludes that it is certainly feasible to attain 100 hours MTBF, for the Model 27, in any and all situations, and hence to provide a reliable MWD for air-drilling.

  3. Connecting onshore and offshore near-surface geology: Delaware's sand inventory project

    Science.gov (United States)

    Ramsey, K.W.; Jordan, R.R.; Talley, J.H.

    1999-01-01

    Beginning in 1988, the Delaware Geological Survey began a program to inventory on-land sand resources suitable for beach nourishment. The inventory included an assessment of the native beach textures using existing data and developing parameters of what would be considered suitable sand textures for Delaware's Atlantic beaches. An assessment of the economics of on-land sand resources was also conducted, and it was determined that the cost of the sand was competitive with offshore dredging costs. In addition, the sand resources were put into a geologic context for purposes of predicting which depositional environments and lithostratigraphic units were most likely to produce suitable sand resources. The results of the work identified several suitable on-land sand resource areas in the Omar and Beaverdam formations that were deposited in barrier-tidal delta and fluvial-estuarine environments, respectively. The identified on-land resources areas have not been utilized due to difficulties of truck transport and development pressures in the resource areas. The Delaware Geological Survey's participation in years 8, 9, and 10 of the Continental Margins Program was developed to extend the known resource areas onshore to offshore Delaware in order to determine potential offshore sand resources for beach nourishment. Years 8 and 9 involved primarily the collection of all available data on the offshore geology. These data included all seismic lines, surface grab samples, and cores. The data were filtered for those that had reliable locations and geologic information that could be used for geologic investigations. Year 10 completed the investigations onshore by construction of a geologic cross-section from data along the coast of Delaware from Cape Henlopen to Fenwick. This cross section identified the geologic units and potential sand resource bodies as found immediately along the coast. These units and resources are currently being extended offshore and tied to known and

  4. Laser Drilling - Drilling with the Power of Light

    Energy Technology Data Exchange (ETDEWEB)

    Brian C. Gahan; Samih Batarseh

    2004-09-28

    Gas Technology Institute (GTI) has been the leading investigator in the field of high power laser applications research for well construction and completion applications. Since 1997, GTI (then as Gas Research Institute) has investigated several military and industrial laser systems and their ability to cut and drill into reservoir type rocks. In this report, GTI continues its investigation with a recently acquired 5.34 kW ytterbium-doped multi-clad high power fiber laser (HPFL). The HPFL represents a potentially disruptive technology that, when compared to its competitors, is more cost effective to operate, capable of remote operations, and requires considerably less maintenance and repair. To determine how this promising laser compares with other lasers used in past experimental work, GTI performed a number of experiments with results directly comparable to previous data. Experiments were designed to investigate the effect of laser input parameters on representative reservoir rock types of sandstone and limestone. The focus of the experiments was on completion and perforation applications, although the results and techniques apply to well construction and other rock cutting applications. Variables investigated include laser power, beam intensity, external purging of cut materials, sample orientation, beam duration, beam shape, and beam frequency. The investigation also studied the thermal effects on the two sample rock types and their methods of destruction: spallation for sandstone, and thermal dissociation for limestone. Optimal operating conditions were identified for each rock type and condition. As a result of this experimental work, the HPFL has demonstrated a better capability of cutting and drilling limestone and sandstone when compared with other military and industrial lasers previously tested. Consideration should be given to the HPFL as the leading candidate for near term remote high power laser applications for well construction and completion.

  5. Successful application of MPD (managed pressure drilling) for prevention, control, and detection of borehole ballooning in tight gas reservoir in Cuervito Field, Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Ochoa, A.; Acevedo, O.; Nieto, L. [Petrobras (United States); Lambarria, J.E. [PEMEX Exploration and Production (Mexico); Perez, H. [Weatherford (United States)

    2011-07-01

    The Cuervito field is an oil play located in the Burgos Basin in northeastern Mexico. In order to reach the highest yielding sands, wells in the Cuervito field are usually set up with 3 casings. However, the ballooning effect, an elastoplastic behavior of a well's walls, occurs during drilling operations, leading to loss of circulation. Two methods, based on geological and geopressure data, were found to minimize this effect: either putting in an extra casing, or using an unconventional drilling technique. As the managed pressure drilling (MPD) technique is less complex and more elegant, a pilot project was implemented using this method on a well. Results showed that MPD minimized lost time and enhanced drilling efficiency. This paper demonstrated that the use of MPD in the Cuervito field is a good solution for identifying and controlling the ballooning effect and this technique was successfully applied to the next 3 wells drilled subsequently.

  6. Advanced Oil Recovery Technologies for Improved Recovery from Slope Basin Clastic Reservoirs, Nash Draw Brushy Canyon Pool, Eddy County, NM

    Energy Technology Data Exchange (ETDEWEB)

    Mark B. Murphy

    2005-09-30

    The Nash Draw Brushy Canyon Pool in Eddy County New Mexico was a cost-shared field demonstration project in the U.S. Department of Energy Class III Program. A major goal of the Class III Program was to stimulate the use of advanced technologies to increase ultimate recovery from slope-basin clastic reservoirs. Advanced characterization techniques were used at the Nash Draw Pool (NDP) project to develop reservoir management strategies for optimizing oil recovery from this Delaware reservoir. The objective of the project was to demonstrate that a development program, which was based on advanced reservoir management methods, could significantly improve oil recovery at the NDP. Initial goals were (1) to demonstrate that an advanced development drilling and pressure maintenance program can significantly improve oil recovery compared to existing technology applications and (2) to transfer these advanced methodologies to other oil and gas producers. Analysis, interpretation, and integration of recently acquired geological, geophysical, and engineering data revealed that the initial reservoir characterization was too simplistic to capture the critical features of this complex formation. Contrary to the initial characterization, a new reservoir description evolved that provided sufficient detail regarding the complexity of the Brushy Canyon interval at Nash Draw. This new reservoir description was used as a risk reduction tool to identify 'sweet spots' for a development drilling program as well as to evaluate pressure maintenance strategies. The reservoir characterization, geological modeling, 3-D seismic interpretation, and simulation studies have provided a detailed model of the Brushy Canyon zones. This model was used to predict the success of different reservoir management scenarios and to aid in determining the most favorable combination of targeted drilling, pressure maintenance, well stimulation, and well spacing to improve recovery from this reservoir. An

  7. Evaluation of commercial drilling and geological software for deep drilling applications

    Science.gov (United States)

    Pierdominici, Simona; Prevedel, Bernhard; Conze, Ronald; Tridec Team

    2013-04-01

    The avoidance of operational delays, financial losses and drilling hazards are key indicators for successful deep drilling operations. Real-time monitoring of drilling operation data as well as geological and petrophysical information obtained during drilling provide valuable knowledge that can be integrated into existing geological and mechanical models in order to improve the drilling performance. We have evaluated ten different geological and drilling software packages capable to integrate real-time drilling and planning data (e.g. torque, drag, well path, cementing, hydraulic data, casing design, well control, geo-steering, cost and time) as well as other scientific and technical data (i.e. from drilling core, geophysical downhole logging, production test) to build geological and geophysical models for planning of further deep drillings in a given geological environment. To reach this goal, the software has to be versatile to handle different data formats from disciplines such as geology, geophysics, petrophysics, seismology and drilling engineering as well as data from different drilling targets, such as geothermal fluids, oil/gas, water reservoirs, mining purpose, CO2 sequestration, or scientific goals. The software must be capable to analyze, evaluate and plan in real-time the next drilling steps in the best possible way and under safe conditions. A preliminary geological and geophysical model with the available data from site surveys and literature is built to address a first drilling plan, in which technical and scientific aspects are taken into consideration to perform the first drilling (wildcat well). During the drilling, the acquired scientific and technical data will be used to refine the previous geological-drilling model. The geological model hence becomes an interactive object strongly linked to the drilling procedure, and the software should allow to make rapid and informed decisions while drilling, to maximize productivity and minimize drilling

  8. Composition and temporal patterns of larval fish communities in Chesapeake and Delaware Bays

    Directory of Open Access Journals (Sweden)

    Filipe Ribeiro

    2015-11-01

    Full Text Available Comparing larval fish assemblages in different estuaries provides insights about the coastal distribution of larval populations, larval transport, and adult spawning locations (Ribeiro et al. 2015. We simultaneously compared the larval fish assemblages entering two Middle Atlantic Bight (MAB estuaries (Delaware Bay and Chesapeake Bay, USA through weekly sampling from 2007 to 2009. In total, 43 taxa (32 families and 36 taxa (24 families were collected in Delaware and Chesapeake Bays, respectively. Mean taxonomic diversity, mean richness, and evenness were generally lower in Delaware Bay. Communities of both bays were dominated by Anchoa spp., Gobiosoma spp., Micropogonias undulatus, and Brevoortia tyrannus; Paralichthys spp. was more abundant in Delaware Bay and Microgobius thalassinus was more abundant in Chesapeake Bay. Inter-annual variation in the larval fish communities was low at both sites, with a relatively consistent composition across years, but strong seasonal (intra-annual variation in species composition occurred in both bays. Two groups were identified in Chesapeake Bay: a ‘winter’ group dominated by shelf-spawned species (e.g. M. undulatus and a ‘summer’ group comprising obligate estuarine species and coastal species (e.g. Gobiosoma spp. and Cynoscion regalis, respectively. In Delaware Bay, 4 groups were identified: a ‘summer’ group of mainly obligate estuarine fishes (e.g. Menidia sp. being replaced by a ‘fall’ group (e.g. Ctenogobius boleosoma and Gobionellus oceanicus; ‘winter’ and ‘spring’ groups were dominated by shelf-spawned (e.g. M. undulatus and Paralichthys spp. and obligate estuarine species (e.g. Leiostomus xanthurus and Pseudopleuronectes americanus, respectively. This study demonstrates that inexpensive and simultaneous sampling in different estuaries provides important insights into the variability in community structure of fish assemblages at large spatial scales.

  9. Foam drilling in natural gas hydrate

    Directory of Open Access Journals (Sweden)

    Wei Na

    2015-01-01

    Full Text Available The key problem of foam drilling in natural gas hydrate is prediction of characteristic parameters of bottom hole. The simulation shows that when the well depth increases, the foam mass number reduces and the pressure increases. At the same depth, pressure in drill string is always higher than annulus. The research findings provide theoretical basis for safety control.

  10. Number & operations drill sheets : grades PK-2

    CERN Document Server

    Reed, Nat

    2010-01-01

    For grades PK-2, our Common Core State Standards-based resource meets the number & operations concepts addressed by the NCTM standards and encourages the students to review the concepts in unique ways. Each drill sheet contains warm-up and timed drill activities for the student to practice number & operations concepts.

  11. 75 FR 877 - Drill Pipe From China

    Science.gov (United States)

    2010-01-06

    ... COMMISSION Drill Pipe From China AGENCY: International Trade Commission. ACTION: Institution of antidumping... States is materially retarded, by reason of imports from China of drill pipe, provided for in subheadings... Government of China. Unless the Department of Commerce extends the time for initiation pursuant to...

  12. 30 CFR 56.7009 - Drill helpers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drill helpers. 56.7009 Section 56.7009 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet...

  13. 30 CFR 57.7801 - Jet drills.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Jet drills. 57.7801 Section 57.7801 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet...

  14. 30 CFR 57.7009 - Drill helpers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drill helpers. 57.7009 Section 57.7009 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet...

  15. 30 CFR 56.7052 - Drilling positions.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drilling positions. 56.7052 Section 56.7052 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary...

  16. 30 CFR 57.7052 - Drilling positions.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drilling positions. 57.7052 Section 57.7052 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and...

  17. 30 CFR 57.7004 - Drill mast.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drill mast. 57.7004 Section 57.7004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet...

  18. 30 CFR 56.7801 - Jet drills.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Jet drills. 56.7801 Section 56.7801 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet...

  19. 30 CFR 56.7004 - Drill mast.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drill mast. 56.7004 Section 56.7004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet...

  20. Status Report A Review of Slimhole Drilling

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Tao; Carroll, Herbert B.

    1994-09-01

    This 1994 report reviews the various applications of slimhole technology including for exploration in remote areas, low-cost development wells, reentering existing wells, and horizontal and multilateral drilling. Advantages of slimholes to regular holes are presented. Limitations and disadvantages of slimholes are also discussed. In 1994, slimhole drilling was still an ongoing development technology. (DJE 2005)

  1. 30 CFR 77.1007 - Drilling; general.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Drilling; general. 77.1007 Section 77.1007 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH... Control § 77.1007 Drilling; general. (a) Equipment that is to be used during a shift shall be...

  2. Straight hole drilling machines for coal mines

    Science.gov (United States)

    Timonin, VV; Kokoulin, DI; Alekseev, SE; Kubanychbek, B.

    2017-02-01

    The authors prove the demand for drilling machines capable of making long straight holes in rocks with the strength up to 120 MPa. The paper describes the designed, manufactured and tested down-the-hole hammers for rotary–percussion drilling of long straight directional holes. The hammers have been delivered to Berezovskaya Mine for further trial and commercial operation.

  3. Neurosurgical robotic arm drilling navigation system.

    Science.gov (United States)

    Lin, Chung-Chih; Lin, Hsin-Cheng; Lee, Wen-Yo; Lee, Shih-Tseng; Wu, Chieh-Tsai

    2017-09-01

    The aim of this work was to develop a neurosurgical robotic arm drilling navigation system that provides assistance throughout the complete bone drilling process. The system comprised neurosurgical robotic arm navigation combining robotic and surgical navigation, 3D medical imaging based surgical planning that could identify lesion location and plan the surgical path on 3D images, and automatic bone drilling control that would stop drilling when the bone was to be drilled-through. Three kinds of experiment were designed. The average positioning error deduced from 3D images of the robotic arm was 0.502 ± 0.069 mm. The correlation between automatically and manually planned paths was 0.975. The average distance error between automatically planned paths and risky zones was 0.279 ± 0.401 mm. The drilling auto-stopping algorithm had 0.00% unstopped cases (26.32% in control group 1) and 70.53% non-drilled-through cases (8.42% and 4.21% in control groups 1 and 2). The system may be useful for neurosurgical robotic arm drilling navigation. Copyright © 2016 John Wiley & Sons, Ltd.

  4. Basic Land Drills for Swimming Stroke Acquisition

    Science.gov (United States)

    Zhang, Peng

    2014-01-01

    Teaching swimming strokes can be a challenging task in physical education. The purpose of the article is to introduce 12 on land drills that can be utilized to facilitate the learning of swimming strokes, including elementary back stroke, sidestroke, front crawl, back stroke, breaststroke, and butterfly. Each drill consists of four components…

  5. Electric motor for laser-mechanical drilling

    Energy Technology Data Exchange (ETDEWEB)

    Grubb, Daryl L.; Faircloth, Brian O.; Zediker, Mark S.

    2015-07-07

    A high power laser drilling system utilizing an electric motor laser bottom hole assembly. A high power laser beam travels within the electric motor for advancing a borehole. High power laser drilling system includes a down hole electrical motor having a hollow rotor for conveying a high power laser beam through the electrical motor.

  6. Feasibility Study of Economics and Performance of Solar Photovoltaics at the Standard Chlorine of Delaware Superfund Site in Delaware City, Delaware. A Study Prepared in Partnership with the Environmental Protection Agency for the RE-Powering America's Land Initiative: Siting Renewable Energy on Potentially Contaminated Land and Mine Sites

    Energy Technology Data Exchange (ETDEWEB)

    Salasovich, J.; Geiger, J.; Mosey, G.; Healey, V.

    2013-06-01

    The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative, selected the Standard Chlorine of Delaware site in Delaware City, Delaware, for a feasibility study of renewable energy production. The National Renewable Energy Laboratory (NREL) provided technical assistance for this project. The purpose of this report is to assess the site for a possible photovoltaic (PV) system installation and estimate the cost, performance, and site impacts of different PV options. In addition, the report recommends financing options that could assist in the implementation of a PV system at the site.

  7. Heat Generation During Bone Drilling: A Comparison Between Industrial and Orthopaedic Drill Bits.

    Science.gov (United States)

    Hein, Christopher; Inceoglu, Serkan; Juma, David; Zuckerman, Lee

    2017-02-01

    Cortical bone drilling for preparation of screw placement is common in multiple surgical fields. The heat generated while drilling may reach thresholds high enough to cause osteonecrosis. This can compromise implant stability. Orthopaedic drill bits are several orders more expensive than their similarly sized, publicly available industrial counterparts. We hypothesize that an industrial bit will generate less heat during drilling, and the bits will not generate more heat after multiple cortical passes. We compared 4 4.0 mm orthopaedic and 1 3.97 mm industrial drill bits. Three types of each bit were drilled into porcine femoral cortices 20 times. The temperature of the bone was measured with thermocouple transducers. The heat generated during the first 5 drill cycles for each bit was compared to the last 5 cycles. These data were analyzed with analysis of covariance. The industrial drill bit generated the smallest mean increase in temperature (2.8 ± 0.29°C) P industrial bit generated less heat during drilling than its orthopaedic counterparts. The bits maintained their performance after 20 drill cycles. Consideration should be given by manufacturers to design differences that may contribute to a more efficient cutting bit. Further investigation into the reuse of these drill bits may be warranted, as our data suggest their efficiency is maintained after multiple uses.

  8. Paleomagnetic applications in hydrocarbon exploration and drilling operations

    Energy Technology Data Exchange (ETDEWEB)

    Van Alstine, D.R.; Bleakly, D.C.; Gillett, S.L.

    1983-03-01

    A new generation of high-sensitivity cryogenic magnetometers permits paleomagnetic applications in weakly magnetized sedimentary rocks. One of the most useful paleomagnetic applications is drill-core orientation, which is important for determining fracture orientations, for stress analysis, and for determining sediment transport directions. A 2-year study involving approximately 600 core plug samples from five wells in three Rocky Mountain basins yielded paleomagnetic orientations that agree with those obtained using the conventional photographic multishot technique. The strongest paleomagnetic signal in these rocks points toward the late Cenozoic paleomagnetic pole and probably represents a secondary magnetization imposed by thermal effects associated with the late Cenozoic uplift and tectonism in this region. Weaker paleomagnetic signals, reflecting earlier thermal, diagenetic, or depositional magnetizations are also commonly preserved in sedimentary rocks and can also be used to orient core.

  9. Sediment flow routing during formation of forearc basins: Constraints from integrated analysis of detrital pyroxenes and stratigraphy in the Kumano Basin, Japan

    Science.gov (United States)

    Buchs, David M.; Cukur, Deniz; Masago, Hideki; Garbe-Schönberg, Dieter

    2015-03-01

    The evolution of sediment flow routing during complete evolution of the Kumano forearc basin is determined through integration of stratigraphic and sediment provenance analyses in the upper Nankai forearc. A new approach uses the compositional variability of detrital clinopyroxenes and orthopyroxenes collected at eight major rivers in Japan and three drill sites in the basin and nearby slope environment, including the first drill cuttings retrieved by the Integrated Ocean Drilling Program (IODP). Joint interpretation of these datasets reveals that the sedimentation history of the basin is characterised by three main phases separated by newly-recognised time-transgressive boundaries. We show that the Kumano Basin initiated as a trench-slope basin in the early Quaternary (∼1.93 Ma) and that it progressively evolved towards an upper slope environment with increased turbidite confinement and influence from climatic forcing. Basin initiation was broadly synchronous with development of the Nankai megasplay fault, suggesting a causal relationship with construction of the Nankai accretionary prism. Unlike preceding studies documenting long-distance longitudinal transport of clastic material along the lower Nankai forearc, only limited longitudinal transport is documented by detrital pyroxenes in the upper forearc. These results suggest that transverse canyons are a major control on the sediment flow routing during maturation of forearc basins and that long-distance longitudinal flows along convergent margins are principally restricted to near-trench environments, even in the presence of large forearc basins.

  10. Communication adapter for use with a drilling component

    Science.gov (United States)

    Hall, David R.; Pixton, David S.; Hall; Jr.; H. Tracy; Bradford, Kline; Rawle, Michael

    2007-04-03

    A communication adapter is disclosed that provides for removable attachment to a drilling component when the drilling component is not actively drilling and for communication with an integrated transmission system in the drilling component. The communication adapter comprises a data transmission coupler that facilitates communication between the drilling component and the adapter, a mechanical coupler that facilitates removable attachment of the adapter to the drilling component, and a data interface.

  11. Peculiarities of carbon fiber drilling

    Directory of Open Access Journals (Sweden)

    Ruslan Yu. Melentiev

    2014-12-01

    Full Text Available At polymeric composite materials (PCM machining we face a number of specific features. The research refers to PCMs classification, exposing an overview of known specific features described in the latest advances and techniques to improve the quality and efficiency in PCM processing. To study the carbon fiber drilling a preliminary experiment has been conducted, which essential parameters and issues have been described with respective data Tables and numerous images. The holes surface quality and edges dimensional accuracy have been compared for samples obtained using a blade and a diamond tool; established is the instrument blade material impact on the edges’ precision parameters. Confirmed are the typical and revealed some new types of imperfections and their occurrence conditions. The problem of rapid clogging and related diamond tool clogging problem are identified. Some promising ways of processing of carbon fiber are offered.

  12. Drilling the North Anatolian Fault

    Directory of Open Access Journals (Sweden)

    Mustafa Aktar

    2008-07-01

    Full Text Available An international workshop entitled “GONAF: A deep Geophysical Observatory at the North Anatolian Fault”, was held 23–27 April 2007 in Istanbul, Turkey. The aim of this workshop was to refine plans for a deep drilling project at the North Anatolian Fault Zone (NAFZ in northwestern Turkey. The current drilling target is located in the Marmara Sea offshore the megacity of Istanbul in the direct vicinity of the main branch of the North Anatolian Fault on the PrinceIslands (Figs. 1 and 2.The NAFZ represents a 1600-km-long plate boundary that slips at an average rate of 20–30 mm·yr-1 (McClusky et al., 2000. It has developed in the framework of the northward moving Arabian plate and the Hellenic subduction zone where the African lithosphere is subducting below the Aegean. Comparison of long-term slip rates with Holocene and GPS-derived slip rates indicate an increasing westwardmovement of the Anatolian plate with respect to stable Eurasia. During the twentieth century, the NAFZ has ruptured over 900 km of its length. A series of large earthquakes starting in 1939 near Erzincan in Eastern Anatolia propagated westward towards the Istanbul-Marmara region in northwestern Turkey that today represents a seismic gap along a ≥100-km-long segment below the Sea of Marmara. This segment did not rupture since 1766 and, if locked, may have accumulated a slip deficit of 4–5 m. It is believed being capable of generating two M≥7.4 earthquakes within the next decades (Hubert-Ferrari et al., 2000; however, it could even rupture in a large single event (Le Pichon et al., 1999.

  13. AIR AND GAS DRILLING SUCCEEDED IN NORTHEASTERN SICHUAN

    Institute of Scientific and Technical Information of China (English)

    Cai Tingyong

    2006-01-01

    @@ On January 21, 2006, air and gas deep well drilling test was successfully carried out in the Sinopec southern exploration area. Lingering problems pestering deep well drillings in the southern marine facies area like low drilling rate and prolonged drilling periods were well resolved: average drilling rate of conventional drilling is about 1.4 meters per hour with drilling period (above Xujiahe Formation) of about 130 days, whereas it took only 22 days to complete the same task by air and gas drilling, with penetration rate increased more than eightfold.

  14. Comparative experiments of gas drainage in different types of drillings

    Institute of Scientific and Technical Information of China (English)

    LI Cheng-wu; WEI Shan-yang; WANG Chuan; GAO Tian-bao; FU Yu-kai

    2012-01-01

    Gas drainage effect is the utmost important factor for mining speed and mining safety.It has great meaning to study the effect of gas drainage.Comparative experiment of gas drainage in different types of drillings shows that the initial rate of gas natural emission by hydraulic loosed cross drilling is 1.5 times more than that of parallel drilling,and the drilling gas attenuation coefficients reduces to 0.78 times,the effect of gas drainage is good.The ultimate quantity of gas drainage of parallel drilling,cross drilling,hydraulic loosed cross drilling are 859.1,1 323.5 and 1 833.6 m3/100 m.The results of the measurement through these three kinds of drillings of 100 meters drilling is considered as following:cross drilling is 1.54 times more than that of parallel drillings,hydraulic loosed cross drilling are 2.13 times more than parallel drilling.The drainage rate of parallel drilling,cross drilling and hydraulic loosed cross drilling reached 10% to 15% in 3 months with the pre-draining time.Among these,the drainage effect of hydraulic loosed cross drilling increased by 46% than that of parallel drilling in three months.

  15. Environmental Sensitivity Index (ESI) Atlas: Delaware, New Jersey, Pennsylvania, maps and geographic information systems data (NODC Accession 0014793)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set comprises the Environmental Sensitivity Index (ESI) data for Delaware, New Jersey, and Pennsylvania from 1969 to 2000(May 2002 v.3). ESI data...

  16. RoxAnn Acoustic Sensor Data Points - Rehoboth Bay, Delaware Algae Mapping with Single Beam Acoustics: June 12 - 16, 2000

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — During the spring of 1999, the Delaware Coastal Programs(DCP) identified the spatial extent of macroalgae in the shallow portions of Rehoboth Bay utilizing...

  17. NOAA Office for Coastal Management RoxAnn Acoustic Sensor Benthic Habitat Data, Rehoboth Bay, Delaware, 2000 (NODC Accession 0089461)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — During the spring of 1999, the Delaware Coastal Programs (DCP) identified the spatial extent of macroalgae in the shallow portions of Rehoboth Bay utilizing...

  18. Biological, chemical, and physical data collected in Delaware Bay from 2 Sep 1997 to 8 Oct 1997 (NODC Accession 0118720)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This study was based on the sediment quality triad (SQT) approach. A stratified probabilistic sampling design was utilized to characterize the Delaware Bay system in...

  19. Counter-Rotating Tandem Motor Drilling System

    Energy Technology Data Exchange (ETDEWEB)

    Kent Perry

    2009-04-30

    Gas Technology Institute (GTI), in partnership with Dennis Tool Company (DTC), has worked to develop an advanced drill bit system to be used with microhole drilling assemblies. One of the main objectives of this project was to utilize new and existing coiled tubing and slimhole drilling technologies to develop Microhole Technology (MHT) so as to make significant reductions in the cost of E&P down to 5000 feet in wellbores as small as 3.5 inches in diameter. This new technology was developed to work toward the DOE's goal of enabling domestic shallow oil and gas wells to be drilled inexpensively compared to wells drilled utilizing conventional drilling practices. Overall drilling costs can be lowered by drilling a well as quickly as possible. For this reason, a high drilling rate of penetration is always desired. In general, high drilling rates of penetration (ROP) can be achieved by increasing the weight on bit and increasing the rotary speed of the bit. As the weight on bit is increased, the cutting inserts penetrate deeper into the rock, resulting in a deeper depth of cut. As the depth of cut increases, the amount of torque required to turn the bit also increases. The Counter-Rotating Tandem Motor Drilling System (CRTMDS) was planned to achieve high rate of penetration (ROP) resulting in the reduction of the drilling cost. The system includes two counter-rotating cutter systems to reduce or eliminate the reactive torque the drillpipe or coiled tubing must resist. This would allow the application of maximum weight-on-bit and rotational velocities that a coiled tubing drilling unit is capable of delivering. Several variations of the CRTDMS were designed, manufactured and tested. The original tests failed leading to design modifications. Two versions of the modified system were tested and showed that the concept is both positive and practical; however, the tests showed that for the system to be robust and durable, borehole diameter should be substantially larger

  20. Comparative status and assessment of Limulus polyphemus with emphasis on the New England and Delaware Bay populations

    Science.gov (United States)

    Smith, David; Millard, Michael J.; Carmichael, Ruth H.

    2009-01-01

    Increases in harvest of the American horseshoe crab (Limulus polyphemus) during the 1990s, particularly for whelk bait, coupled with decreases in species that depend on their eggs has reduced horseshoe crab abundance, threatened their ecological relationships, and dictated precautionary management of the horseshoe crab resource. Accordingly, population assessments and monitoring programs have been developed throughout much of the horseshoe crab’s range. We review and discuss implications for several recent assessments of Delaware Bay and New England populations and a meta-analysis of region-specific trends. These assessments show that the western Atlantic distribution of the horseshoe crab is comprised of regional or estuarine-specific meta-populations, which exhibit distinct population dynamics and require management as separate units. Modeling of Delaware Bay and Cape Cod populations confirmed that overharvest caused declines, but indicated that some harvest levels are sustainable and consistent with population growth. Coast-wide harvest was reduced by 70% from 1998 to 2006, with the greatest reductions within Delaware Bay states. Harvest regulations in Delaware Bay starting in the late 1990s, such as harvest quotas, seasonal closures, male-only harvest, voluntary use of bait-saving devices, and establishment of the Carl N. Shuster Jr. Horseshoe Crab Reserve, were followed by stabilization and recent evidence of increase in abundance of horseshoe crabs in the region. However, decreased harvest of the Delaware Bay population has redirected harvest to outlying populations, particularly in New York and New England. While the recent Delaware Bay assessments indicate positive population growth, increased harvest elsewhere is believed to be unsustainable. Two important considerations for future assessments include (1) managing Delaware Bay horseshoe crab populations within a multi-species context, for example, to help support migratory shorebirds and (2

  1. Robot force control for hazardous drilling operations

    Science.gov (United States)

    Alici, Gursel; Daniel, R. W.

    The use of robot manipulators for tasks which are inherently risky for human beings, specifically hazardous drilling operations, is investigated. Although drilling is one of the simplest and most basic metal cutting processes, robot drilling is problematic and has resulted in extreme operator fatigue and shorter drill life under telemanipulator control due to a number of possible causes such as dynamic and static effects. Both originate from differences between a robot and a drilling machine. A detailed study of the task highlighted the fact that it is necessary to regulate the distance dependent force by closed loop force control. How the robot type force could be controlled together with the robot position to allow fast drilling but without too much drill wear was considered. The answer was found in further exploration of the tasks which generated a set of specifications and problems that were addressed using novel strategies rather than those usually adopted for robots. The possible solutions are given in terms of a new control strategy and the correct choice of coordinate system to be used within that strategy.

  2. The Auto-Gopher Deep Drill

    Science.gov (United States)

    Badescu, Mircea

    2014-01-01

    Subsurface penetration by coring, drilling or abrading is of great importance for a large number of space and earth applications. An Ultrasonic/Sonic Drill/Corer (USDC) has been in development at JPL's Nondestructive Evaluation and Advanced Actuators (NDEAA) lab as an adaptable tool for many of these applications. The USDC uses a novel drive mechanism to transform the high frequency ultrasonic or sonic vibrations of the tip of a horn into a lower frequency sonic hammering of a drill bit through an intermediate free-flying mass. The USDC device idea has been implemented at various scales from handheld drills to large diameter coring devices. A series of computer programs that model the function and performance of the USDC device were developed and were later integrated into an automated modeling package. The USDC has also evolved from a purely hammering drill to a rotary hammer drill as the design requirements increased form small diameter shallow drilling to large diameter deep coring. A synthesis of the Auto-Gopher development is presented in this paper.

  3. Steamboat Hills exploratory slimhole: Drilling and testing

    Energy Technology Data Exchange (ETDEWEB)

    Finger, J.T.; Jacobson, F.D.; Hickox, C.E.; Eaton, R.R.

    1994-10-01

    During July-September, 1993, Sandia National Laboratories, in cooperation with Far West Capital, drilled a 4000 feet exploratory slimhole (3.9 inch diameter) in the Steamboat Hills geothermal field near Reno, Nevada. This well was part of Sandia`s program to evaluate slimholes as a geothermal exploration tool. During and after drilling the authors performed four series of production and injection tests while taking downhole (pressure-temperature-spinner) and surface (wellhead pressure and temperature, flow rate) data. In addition to these measurements, the well`s data set includes: continuous core (with detailed log); borehole televiewer images of the wellbore`s upper 500 feet; daily drilling reports from Sandia and from drilling contractor personnel; daily drilling fluid record; numerous temperature logs; and comparative data from production and injection wells in the same field. This report contains: (1) a narrative account of the drilling and testing, (2) a description of equipment used, (3) a brief geologic description of the formation drilled, (4) a summary and preliminary interpretation of the data, and (5) recommendations for future work.

  4. The University of Delaware Carlson International Polar Year Events: Collaborative and Educational Outreach

    Science.gov (United States)

    Nelson, F. E.; Bryant, T.; Wellington, P.; Dooley, J.; Bird, M.

    2008-12-01

    Delaware is a small state with, by virtue of its coastal location, a large stake in climatic change in the polar regions. The University of Delaware has maintained a strong presence in cold-regions research since the mid-1940s, when William Samuel Carlson, a highly accomplished Arctic explorer, military strategist, and earth scientist, was named 20th President (1946-50) of the University. Carlson played a leading role in two of the University of Michigan's Greenland expeditions in the late 1920s and early 1930s. As Director of the Arctic, Desert, and Tropic Branch of the US Army Air Forces Tactical Center during World War II, Colonel Carlson played a role in developing several air transportation routes through the Arctic that helped to facilitate the Allied victory in Europe. Carlson authored many scientific and popular publications concerned with the Arctic, including the books Greenland Lies North (1940) and Lifelines Through the Arctic (1962). Although the University of Delaware has maintained a vigorous and continuous program of polar research since Carlson's tenure, the faculty, staff, and students involved are diffused throughout the University's colleges and departments, without an institutional focal point. Consequently, although many of these individuals are well known in their respective fields, the institution has not until recently been perceived widely as a center of polar-oriented research. The goals of the Carlson International Polar Year Events are to: (a) develop a sense of community among UD's diffuse polar-oriented researchers and educators; (b) create a distinctive and highly visible role for UD in the milieu of IPY activities; (c) promote interest in and knowledge about the polar regions in the State of Delaware, at all educational levels; (d) forge a close relationship between UD and the American Geographical Society, a national organization involved closely with previous International Polar Years; and (e) create a new basis for development

  5. Lack of training threatening drilling talent supply

    Energy Technology Data Exchange (ETDEWEB)

    Von Flatern, R.

    1996-07-01

    When oil prices crashed in the mid-1980s, the industry tightened budgets. Among the austerity measures taken to survive the consequences of low product prices was an end to expensive, long-term investment training of drilling engineers. In the absence of traditional sources of trained drilling talent, forward-looking contractors are creating their own training programs. The paper describes the activities of some companies who are setting up their own training programs, and an alliance being set up by Chevron and Amoco for training. The paper also discusses training drilling managers, third-party trainers, and the consequences for the industry that does not renew its inventory of people.

  6. Modal Analysis of Drilling Machine Derrick

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In this paper, the finite element analysis software ( ANSYS ) is applied to the modal analysis of a ZJ30/1700CZ 's drilling machine derrick under a natural condition and a loaded condition, respectively. The preceding nine step natural frequencies and the corresponding mode shapes of the derrick are calculated. By means of the comparison of the natural frequency of the derrick with the design work frequency of the drilling machine and the analysis of the step mode shape of the derrick, the drilling machine derrick structure design is proved to be correct.

  7. Fatigue analysis of aluminum drill pipes

    Directory of Open Access Journals (Sweden)

    João Carlos Ribeiro Plácido

    2005-12-01

    Full Text Available An experimental program was performed to investigate the fundamental fatigue mechanisms of aluminum drill pipes. Initially, the fatigue properties were determined through small-scale tests performed in an optic-mechanical fatigue apparatus. Additionally, full-scale fatigue tests were carried out with three aluminum drill pipe specimens under combined loading of cyclic bending and constant axial tension. Finally, a finite element model was developed to simulate the stress field along the aluminum drill pipe during the fatigue tests and to estimate the stress concentration factors inside the tool joints. By this way, it was possible to estimate the stress values in regions not monitored during the fatigue tests.

  8. Feasibility study of heavy oil recovery in the Permian Basin (Texas and New Mexico)

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, D.K.; Johnson, W.I.

    1993-05-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production. Each report covers select areas of the United States. The Permian Basin of West Texas and Southeastern New Mexico is made up of the Midland, Delaware, Val Verde, and Kerr Basins; the Northwestern, Eastern, and Southern shelves; the Central Basin Platform, and the Sheffield Channel. The present day Permian Basin was one sedimentary basin until uplift and subsidence occurred during Pennsylvanian and early Permian Age to create the configuration of the basins, shelves, and platform of today. The basin has been a major light oil producing area served by an extensive pipeline network connected to refineries designed to process light sweet and limited sour crude oil. Limited resources of heavy oil (10`` to 20`` API gravity) occurs in both carbonate and sandstone reservoirs of Permian and Cretaceous Age. The largest cumulative heavy oil production comes from fluvial sandstones of the Cretaceous Trinity Group. Permian heavy oil is principally paraffinic and thus commands a higher price than asphaltic California heavy oil. Heavy oil in deeper reservoirs has solution gas and low viscosity and thus can be produced by primary and by waterflooding. Because of the nature of the resource, the Permian Basin should not be considered a major heavy oil producing area.

  9. Feasibility study of heavy oil recovery in the Permian Basin (Texas and New Mexico)

    Energy Technology Data Exchange (ETDEWEB)

    Olsen, D.K.; Johnson, W.I.

    1993-05-01

    This report is one of a series of publications assessing the feasibility of increasing domestic heavy oil production. Each report covers select areas of the United States. The Permian Basin of West Texas and Southeastern New Mexico is made up of the Midland, Delaware, Val Verde, and Kerr Basins; the Northwestern, Eastern, and Southern shelves; the Central Basin Platform, and the Sheffield Channel. The present day Permian Basin was one sedimentary basin until uplift and subsidence occurred during Pennsylvanian and early Permian Age to create the configuration of the basins, shelves, and platform of today. The basin has been a major light oil producing area served by an extensive pipeline network connected to refineries designed to process light sweet and limited sour crude oil. Limited resources of heavy oil (10'' to 20'' API gravity) occurs in both carbonate and sandstone reservoirs of Permian and Cretaceous Age. The largest cumulative heavy oil production comes from fluvial sandstones of the Cretaceous Trinity Group. Permian heavy oil is principally paraffinic and thus commands a higher price than asphaltic California heavy oil. Heavy oil in deeper reservoirs has solution gas and low viscosity and thus can be produced by primary and by waterflooding. Because of the nature of the resource, the Permian Basin should not be considered a major heavy oil producing area.

  10. Simulation of Runoff and Reservoir Inflow for Use in a Flood-Analysis Model for the Delaware River, Pennsylvania, New Jersey, and New York, 2004-2006

    Science.gov (United States)

    Goode, Daniel J.; Koerkle, Edward H.; Hoffman, Scott A.; Regan, R. Steve; Hay, Lauren E.; Markstrom, Steven L.

    2010-01-01

    A model was developed to simulate inflow to reservoirs and watershed runoff to streams during three high-flow events between September 2004 and June 2006 for the main-stem subbasin of the Delaware River draining to Trenton, N.J. The model software is a modified version of the U.S. Geological Survey (USGS) Precipitation-Runoff Modeling System (PRMS), a modular, physically based, distributed-parameter modeling system developed to evaluate the impacts of various combinations of precipitation, climate, and land use on surface-water runoff and general basin hydrology. The PRMS model simulates time periods associated with main-stem flooding that occurred in September 2004, April 2005, and June 2006 and uses both daily and hourly time steps. Output from the PRMS model was formatted for use as inflows to a separately documented reservoir and riverrouting model, the HEC-ResSim model, developed by the U.S. Army Corps of Engineers Hydrologic Engineering Center to evaluate flooding. The models were integrated through a graphical user interface. The study area is the 6,780 square-mile watershed of the Delaware River in the states of Pennsylvania, New Jersey, and New York that drains to Trenton, N.J. A geospatial database was created for use with a geographic information system to assist model discretization, determine land-surface characterization, and estimate model parameters. The USGS National Elevation Dataset at 100-meter resolution, a Digital Elevation Model (DEM), was used for model discretization into streams and hydrologic response units. In addition, geospatial processing was used to estimate initial model parameters from the DEM and other data layers, including land use. The model discretization represents the study area using 869 hydrologic response units and 452 stream segments. The model climate data for point stations were obtained from multiple sources. These sources included daily data for 22 National Weather Service (NWS) Cooperative Climate Station network

  11. Physical-Property Measurements on Core samples from Drill-Holes DB-1 and DB-2, Blue Mountain Geothermal Prospect, North-Central Nevada

    Science.gov (United States)

    Ponce, David A.; Watt, Janet T.; Casteel, John; Logsdon, Grant

    2009-01-01

    From May to June 2008, the U.S. Geological Survey (USGS) collected and measured physical properties on 36 core samples from drill-hole Deep Blue No. 1 (DB-1) and 46 samples from drill-hole Deep Blue No. 2 (DB-2) along the west side of Blue Mountain about 40 km west of Winnemucca, Nev. These data were collected as part of an effort to determine the geophysical setting of the Blue Mountain geothermal prospect as an aid to understanding the geologic framework of geothermal systems throughout the Great Basin. The physical properties of these rocks and other rock types in the area create a distinguishable pattern of gravity and magnetic anomalies that can be used to infer their subsurface geologic structure. Drill-holes DB-1 and DB-2 were spudded in alluvium on the western flank of Blue Mountain in 2002 and 2004, respectively, and are about 1 km apart. Drill-hole DB-1 is at a ground elevation of 1,325 m and was drilled to a depth of 672 m and drill-hole DB-2 is at a ground elevation of 1,392 m and was drilled to a depth of 1522 m. Diameter of the core samples is 6.4 cm. These drill holes penetrate Jurassic and Triassic metasedimentary rocks predominantly consisting of argillite, mudstone, and sandstone; Tertiary diorite and gabbro; and younger Tertiary felsic dikes.

  12. Estrogen and androgen receptor activities of hydraulic fracturing chemicals and surface and ground water in a drilling-dense region

    Science.gov (United States)

    Kassotis, Christopher D.; Tillitt, Donald E.; Davis, J. Wade; Hormann, Anette M.; Nagel, Susan C.

    2014-01-01

    The rapid rise in natural gas extraction using hydraulic fracturing increases the potential for contamination of surface and ground water from chemicals used throughout the process. Hundreds of products containing more than 750 chemicals and components are potentially used throughout the extraction process, including more than 100 known or suspected endocrine-disrupting chemicals. We hypothesized thataselected subset of chemicalsusedin natural gas drilling operationsandalso surface and ground water samples collected in a drilling-dense region of Garfield County, Colorado, would exhibit estrogen and androgen receptor activities. Water samples were collected, solid-phase extracted, and measured for estrogen and androgen receptor activities using reporter gene assays in human cell lines. Of the 39 unique water samples, 89%, 41%, 12%, and 46% exhibited estrogenic, antiestrogenic, androgenic, and antiandrogenic activities, respectively. Testing of a subset of natural gas drilling chemicals revealed novel antiestrogenic, novel antiandrogenic, and limited estrogenic activities. The Colorado River, the drainage basin for this region, exhibited moderate levels of estrogenic, antiestrogenic, and antiandrogenic activities, suggesting that higher localized activity at sites with known natural gas–related spills surrounding the river might be contributing to the multiple receptor activities observed in this water source. The majority of water samples collected from sites in a drilling-dense region of Colorado exhibited more estrogenic, antiestrogenic, or antiandrogenic activities than reference sites with limited nearby drilling operations. Our data suggest that natural gas drilling operationsmayresult in elevated endocrine-disrupting chemical activity in surface and ground water.

  13. Prediction of the temperature of a drill in drilling lunar rock simulant in a vacuum

    Directory of Open Access Journals (Sweden)

    Cui Jinsheng

    2017-01-01

    Full Text Available In this article, the temperature of a sampling drill in drilling lunar rock simulant in a high-vacuum environment was studied. The thermal problem was viewed as a 1-D transient heat transfer problem in a semi-infinite object. The simplified drill was modeled using heat conduction differential equation and a fast numerical calculation method is proposed on this basis, with time and the drill discretized. The model was modified to consider the effects of radiation, drill bit configuration, and non-constant heat source. A thermal analysis was conducted using ANSYS Workbench to determine the value of the equivalent correction coefficient proposed in this paper. Using fiber Bragg grating temperature measurement method, drilling experiments were conducted in a vacuum, and the results were compared to the model. The agreement between model and experiment was very good.

  14. Study on temperature field of the drilling machine during the course of drilling in coal mine

    Institute of Scientific and Technical Information of China (English)

    LIU Zhi-chao; YU Ming-gao; ZHENG Li-gang; PAN Rong-kun

    2006-01-01

    The working conditions of the MK-3 type full hydraulic tunnel drilling machine during the course of drilling were analyzed. Based on the energy balance governing equations for the drill rod, the temperature field of drill rod at the normal and non-normal working conditions was numerically obtained. The numerical results show that the maximum temperature at the head of drill rod under the normal working circumstance is insufficient to ignite the gas. But under the non-normal working condition, the local high temperature can ignite the gas easily and cause the fire. In order to prevent the gas fire, the occurrence of the non-normal operating condition must be prevented as far as possible during the drilling.

  15. Final Technical Report for “A Heliportable Sonic Drilling Platform for Microhole Drilling and Exploration”

    Energy Technology Data Exchange (ETDEWEB)

    Lucon, Peter

    2008-05-05

    The Phase I objectives were fully achieved the execution of a program that included the: • Development of a comprehensive model of the sonic drill technology and interaction of the dynamic drilling parameters with the impedance of the earth. • Operation and measurement of the sonic drilling process in the field at full scale. • Comparison of the analytical and experimental results to form an objective and quantified approach to describe the fundamental phenomena and to develop a methodology for automated control of the sonic drilling process. • Conceptual design of a modular sonic drilling system that can be transported to remote sites by helicopter. As a result, the feasibility of a commercially viable sonic drilling technology that can produce microholes up to 1,500 feet in depth, and that is field deployable to remote, environmentally sensitive sites via a helicopter, has been demonstrated.

  16. Messinian Salinity Crisis - DREAM (Deep-sea Record of Mediterranean Messinian events) drilling projects

    Science.gov (United States)

    Lofi, Johanna; Camerlenghi, Angelo

    2014-05-01

    About 6 My ago the Mediterranean Sea was transformed into a giant saline basin. This event, commonly referred to as the Messinian salinity crisis (MSC), changed the chemistry of the global ocean and had a permanent impact on both the terrestrial and marine ecosystems of a huge area surrounding the Mediterranean area. The first fascinating MSC scenario was proposed following DSDP Leg XIII in 1970 and envisaged an almost desiccated deep Mediterranean basin with a dramatic ~1,500 m drop of sea level, the incision of deep canyons by rivers on the continental margins, and a final catastrophic flooding event when the connections between the Mediterranean Sea and the Atlantic were re-established ~5.33 My ago. In spite of 40 years of multi-disciplinary research conducted on the MSC, modalities, timing, causes, chronology and consequence at local and planetary scale are still not yet fully understood, and the MSC event remains one of the longest-living controversies in Earth Science. Key factor for the controversy is the lack of a complete record of the MSC preserved in the deepest Mediterranean basins. Anywhere else, the MSC mostly generated a sedimentary/time lag corresponding to a widespread erosion surface. Correlations with the offshore depositional units are thus complex, preventing the construction of a coherent scenario linking the outcropping MSC evaporites, the erosion on the margins, and the deposition of clastics and evaporites in the abyssal plains. Recent activity by various research groups in order to identify locations for multiple-site drilling (including riser-drilling) in the Mediterranean Sea that would contribute to solve the open questions still existing about the MSC has culminated in two DREAM Magellan+ Workshops held in 2013 and 2014. A strategy and work plan have been established in order to submit an IODP Multi-phase Drilling Project("Uncovering A Salt Giant")including several site-specific drilling proposals addressing different scientific

  17. Wintertime Air Quality Impacts from Oil and Natural Gas Drilling Operations in the Bakken Formation Region

    Science.gov (United States)

    Evanoski-Cole, Ashley; Sive, Barkley; Zhou, Yong; Prenni, Anthony; Schurman, Misha; Day, Derek; Sullivan, Amy; Li, Yi; Hand, Jenny; Gebhart, Kristi; Schichtel, Bret; Collett, Jeffrey

    2016-04-01

    Oil and natural gas extraction has dramatically increased in the last decade in the United States due to the increased use of unconventional drilling techniques which include horizontal drilling and hydraulic fracturing. The impact of these drilling activities on local and regional air quality in oil and gas basins across the country are still relatively unknown, especially in recently developed basins such as the Bakken shale formation. This study is the first to conduct a comprehensive characterization of the regional air quality in the Bakken region. The Bakken shale formation, part of the Williston basin, is located in North Dakota and Montana in the United States and Saskatchewan and Manitoba in Canada. Oil and gas drilling operations can impact air quality in a variety of ways, including the generation of atmospheric particulate matter (PM), hazardous air pollutants, ozone, and greenhouse gas emissions. During the winter especially, PM formation can be enhanced and meteorological conditions can favor increased concentrations of PM and other pollutants. In this study, ground-based measurements throughout the Bakken region in North Dakota and Montana were collected over two consecutive winters to gain regional trends of air quality impacts from the oil and gas drilling activities. Additionally, one field site had a comprehensive suite of instrumentation operating at high time resolution to gain detailed characterization of the atmospheric composition. Measurements included organic carbon and black carbon concentrations in PM, the characterization of inorganic PM, inorganic gases, volatile organic compounds (VOCs), precipitation and meteorology. These elevated PM episodes were further investigated using the local meteorological conditions and regional transport patterns. Episodes of elevated concentrations of nitrogen oxides and sulfur dioxide were also detected. The VOC concentrations were analyzed and specific VOCs that are known oil and gas tracers were used

  18. DEVELOPMENT OF NEW DRILLING FLUIDS

    Energy Technology Data Exchange (ETDEWEB)

    David B. Burnett

    2003-08-01

    The goal of the project has been to develop new types of drill-in fluids (DIFs) and completion fluids (CFs) for use in natural gas reservoirs. Phase 1 of the project was a 24-month study to develop the concept of advanced type of fluids usable in well completions. Phase 1 tested this concept and created a kinetic mathematical model to accurately track the fluid's behavior under downhole conditions. Phase 2 includes tests of the new materials and practices. Work includes the preparation of new materials and the deployment of the new fluids and new practices to the field. The project addresses the special problem of formation damage issues related to the use of CFs and DIFs in open hole horizontal well completions. The concept of a ''removable filtercake'' has, as its basis, a mechanism to initiate or trigger the removal process. Our approach to developing such a mechanism is to identify the components of the filtercake and measure the change in the characteristics of these components when certain cleanup (filtercake removal) techniques are employed.

  19. Investigation of the wear of hard-metal drilling tools when drilling cast iron

    OpenAIRE

    Escursell Mor, Anna

    2009-01-01

    Spheroidal cast iron still has a lot of applications; especially in the automotive industry. In this Master Thesis the wear of the drilling tools and its effect on the quality of the drilled holes is being studied. An experimental investigation of different types of tool coatings and geometry will be done to understand the diverse factors that affect the creation of wear. Also the forces involved in the process of drilling will be experimentally calculated. Studying the results, recommenda...

  20. Polyethylene Glycol Drilling Fluid for Drilling in Marine Gas Hydrates-Bearing Sediments: An Experimental Study

    OpenAIRE

    Lixin Kuang; Yibing Yu; Yunzhong Tu; Ling Zhang; Fulong Ning; Guosheng Jiang; Tianle Liu

    2011-01-01

    Shale inhibition, low-temperature performance, the ability to prevent calcium and magnesium-ion pollution, and hydrate inhibition of polyethylene glycol drilling fluid were each tested with conventional drilling-fluid test equipment and an experimental gas-hydrate integrated simulation system developed by our laboratory. The results of these tests show that drilling fluid with a formulation of artificial seawater, 3% bentonite, 0.3% Na 2 CO 3 , 10% polyethylene glycol, 20% NaCl, 4% SMP-2, 1% ...

  1. HORIZONTAL WELL DRILL-IN FLUIDS

    Directory of Open Access Journals (Sweden)

    Nediljka Gaurina-Međimurec

    1998-12-01

    Full Text Available Main objective of horizontal driling is to place a drain-hole for a long distance within the pay zone to enhance productivity or injectivity. In drilling horizontal wells, more serious problems appear than in drilling vertical wells. These problems are: poor hole cleaning, excessive torque and drag, hole filling, pipe stucking, wellbore instability, loss of circulation, formation damage, poor cement job, and difficulties at logging jobs. From that reason, successful drilling and production of horizontal well depends largely on the fluid used during drilling and completion phases. Several new fluids, that fulfill some or all of required properties (hole cleaning, cutting suspension, good lubrication, and relative low formation damage, are presented in this paper.

  2. 75 FR 8113 - Drill Pipe From China

    Science.gov (United States)

    2010-02-23

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Drill Pipe From China AGENCY: United States International Trade Commission. ACTION: Revised schedule for the subject antidumping and countervailing duty investigations. DATES: Effective...

  3. Fort Bliss exploratory slimholes: Drilling and testing

    Energy Technology Data Exchange (ETDEWEB)

    Finger, J.T.; Jacobson, R.D.

    1997-12-01

    During November/96 to April/97 Sandia National Laboratories provided consulation, data collection, analysis and project documentation to the U.S. Army for a series of four geothermal exploratory slimholes drilled on the McGregor Range approximately 25 miles north of El Paso, Texas. This drilling was directed toward evaluating a potential reservoir for geothermal power generation in this area, with a secondary objective of assessing the potential for direct use applications such as space heating or water de-salinization. This report includes: representative temperature logs from the wells; daily drilling reports; a narrative account of the drilling and testing; a description of equipment used; a summary and preliminary interpretation of the data; and recommendations for future work.

  4. Extreme Temperature Motor and Drill System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In response to the need for motors, actuators and drilling systems that can operate in the harsh venusian environment for extended periods of time, on the order of...

  5. Downhole drilling spotting fluid composition and method

    Energy Technology Data Exchange (ETDEWEB)

    Hayes, J.R.; Campbell, G.J.

    1991-03-26

    This paper discusses a spotting fluid concentrate composition suitable for use in downhole drilling operations in a pill for releasing periodically stuck drill string. It comprises glycerophosphoric acid ester; a polyacyloxy polycarboxylic acid ester of monoglycerides, diglycerides and mixtures thereof; an optional viscosifying agent for increasing the viscosity of the dispersion; and an optional sealing agent for preventing diffusion of water into the downhole formation. This patent also describes a method for lubricating a downhole well drilling operation. It comprises mixing a spotting fluid concentrate composition comprising glycerophosphoric acid ester, a polyacyloxy polycarboxylic acid ester of monoglycerides, diglycerides and mixtures thereof, an optional viscosifying agent and an optional sealing agent with drilling mud; and circulating the mud mixture through the well.

  6. Antibiotic 'Report Card' Drills Guidelines into Dentists

    Science.gov (United States)

    ... page: https://medlineplus.gov/news/fullstory_160702.html Antibiotic 'Report Card' Drills Guidelines Into Dentists Seeing their ... HealthDay News) -- Dentists are less likely to prescribe antibiotics for patients after seeing a "report card" on ...

  7. Hydraulic hammer drilling technology: Developments and capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Melamed, Y.; Kiselev, A. [SKB Geotechnika, Moscow (Russian Federation); Gelfgat, M. [Aquatic Co., Moscow (Russian Federation); Dreesen, D.; Blacic, J. [Los Alamos National Lab., NM (United States). GeoEngineering Group

    1996-12-31

    Percussion drilling technology was considered many years ago as one of the best approaches for hard rock drilling. Unfortunately the efficiency of most hydraulic hammer (HH) designs was very low (8% maximum), so they were successfully used in shallow boreholes only. Thirty years of research and field drilling experience with HH application in Former Soviet Union (FSU) countries led to the development of a new generation of HH designs with a proven efficiency of 40%. That advance achieved good operational results in hard rock at depths up to 2,000 m and more. The most recent research has shown that there are opportunities to increase HH efficiency up to 70%. This paper presents HH basic design principles and operational features. The advantages of HH technology for coiled-tubing drilling is shown on the basis of test results recently conducted in the US.

  8. Environment-friendly drilling operation technology

    Science.gov (United States)

    Luo, Huaidong; Jing, Ning; Zhang, Yanna; Huang, Hongjun; Wei, Jun

    2017-01-01

    Under the circumstance that international safety and environmental standards being more and more stringent, drilling engineering is facing unprecedented challenges, the extensive traditional process flow is no longer accepted, the new safe and environment-friendly process is more suitable to the healthy development of the industry. In 2015, CNPCIC adopted environment-friendly drilling technology for the first time in the Chad region, ensured the safety of well control, at the same time increased the environmental protection measure, reduced the risk of environmental pollution what obtain the ratification from local government. This technology carries out recovery and disposal of crude oil, cuttings and mud without falling on the ground. The final products are used in road and well site construction, which realizes the reutilization of drilling waste, reduces the operating cost, and provides a strong technical support for cost-cutting and performance-increase of drilling engineering under low oil price.

  9. IODP Expedition 319, NanTroSEIZE Stage 2: First IODP Riser Drilling Operations and Observatory Installation Towards Understanding Subduction Zone Seismogenesis

    Directory of Open Access Journals (Sweden)

    Sean Toczko

    2010-09-01

    Full Text Available The Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE is a major drilling project designed to investigate fault mechanics and the seismogenic behavior of subduction zone plate boundaries. Expedition 319 is the first riser drilling operation within scientific ocean drilling. Operations included riser drilling at Site C0009 in the forearc basin above the plate boundary fault, non-riser drilling at Site C0010 across the shallow part of the megasplay faultsystem—which may slip during plate boundary earthquakes—and initial drilling at Site C0011 (incoming oceanic plate for Expedition 322. At Site C0009, new methods were tested, including analysis of drill mud cuttings and gas, and in situ measurements of stress, pore pressure, and permeability. These results, in conjunction with earlier drilling, will provide a the history of forearc basin development (including links to growth of the megasplay fault system and modern prism, b the first in situ hydrological measurements of the plate boundary hanging wall, and c integration of in situ stress measurements (orientation and magnitude across the forearc and with depth. A vertical seismic profile (VSP experiment provides improved constraints on the deeper structure of the subduction zone. At Site C0010, logging-while-drilling measurements indicate significantchanges in fault zone and hanging wall properties over short (<5 km along-strike distances, suggesting different burial and/or uplift history. The first borehole observatory instruments were installed at Site C0010 to monitor pressure and temperature within the megasplay fault zone, and methods of deployment of more complex observatoryinstruments were tested for future operations.

  10. New Era of Scientific Ocean Drilling

    Science.gov (United States)

    Eguchi, N.; Toczko, S.; Sanada, Y.; Igarashi, C.; Kubo, Y.; Maeda, L.; Sawada, I.; Takase, K.; Kyo, N.

    2014-12-01

    The D/V Chikyu, committed to scientific ocean drilling since 2007, has completed thirteen IODP expeditions, and Chikyu's enhanced drilling technology gives us the means to reach deep targets, enhanced well logging, deep water riserless drilling, and state of the art laboratory. Chikyu recovered core samples from 2466 meters below sea floor (mbsf) in IODP Exp. 337, and drilled to 3058.5 mbsf in IODP Exp. 348, but these are still not the limit of Chikyu's capability. As deep as these depths are, they are just halfway to the 5200 mbsf plate boundary target for the NanTroSEIZE deep riser borehole. There are several active IODP proposals in the pipeline. Each has scientific targets requiring several thousand meters of penetration below the sea floor. Riser technology is the only way to collect samples and data from that depth. Well logging has been enhanced with the adoption of riser drilling, especially for logging-while-drilling (LWD). LWD has several advantages over wireline logging, and provides more opportunities for continuous measurements even in unstable boreholes. Because of the larger diameter of riser pipes and enhanced borehole stability, Chikyu can use several state-of-the-art downhole tools, e.g. fracture tester, fluid sampling tool, wider borehole imaging, and the latest sonic tools. These new technologies and tools can potentially expand the envelope of scientific ocean drilling. Chikyu gives us access to ultra-deep water riserless drilling. IODP Exp. 343/343T investigating the March 2011 Tohoku Oki Earthquake, explored the toe of the landward slope of the Japan Trench. This expedition reached the plate boundary fault target at more than 800 mbsf in water depths over 6900 m for logging-while-drilling, coring, and observatory installation. This deep-water drilling capability also expands the scientific ocean drilling envelope and provides access to previously unreachable targets. On top of these operational capabilities, Chikyu's onboard laboratory is

  11. 21 CFR 872.4130 - Intraoral dental drill.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Intraoral dental drill. 872.4130 Section 872.4130...) MEDICAL DEVICES DENTAL DEVICES Surgical Devices § 872.4130 Intraoral dental drill. (a) Identification. An intraoral dental drill is a rotary device intended to be attached to a dental handpiece to drill holes...

  12. Buckling and dynamic analysis of drill strings for core sampling

    Energy Technology Data Exchange (ETDEWEB)

    Ziada, H.H., Westinghouse Hanford

    1996-05-15

    This supporting document presents buckling and dynamic stability analyses of the drill strings used for core sampling. The results of the drill string analyses provide limiting operating axial loads and rotational speeds to prevent drill string failure, instability and drill bit overheating during core sampling. The recommended loads and speeds provide controls necessary for Tank Waste Remediation System (TWRS) programmatic field operations.

  13. Thermal numerical assessment of jawbone drilling factor during implantology

    Directory of Open Access Journals (Sweden)

    Adel Pirjamali Neisiani

    2016-03-01

    Full Text Available Background and Aims: Optimization drilling parameters in order to temperature decrease during creation of hole in the bone is an interested issue. The aim of this study was to achieve optimum values of drilling parameters based on the creation of minimum temperature during jawbone drilling. Materials and Methods: In this study two models of mandible and maxilla was created and teeth 2, 5 and 8 from maxilla and teeth 25, 28 and 31 from mandible were removed. The drilling operation was performed under different conditions on jawbone models using finite element analysis and the maximum temperatures were measured in adjacent of holes. Results: Drill bit head angle of 70 degrees was created the lowest maximum temperature during drilling operation. The lowest maximum temperatures were observed in the drill bit rotational speed, drill bit feed rate and the force exerted on the drill bit equal to 200 rpm, 120 mm/min and 60 N, respectively. The use of irrigation can decrease the maximum bone temperature about 7ºC. The maximum temperature differences in various regions of mandible and maxilla were approximately about 1ºC. Conclusion: Sharpness of drill bit head angle, reduction of drill bit rotational speed, increasing drill bit feed rate and exerted force on drill bit and also the use of irrigation played effective roles in temperature decrease during jawbone drilling. Drilling site did not have important effect on the temperature changes during jawbone drilling.

  14. 30 CFR 250.463 - Who establishes field drilling rules?

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Who establishes field drilling rules? 250.463... GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Other Drilling Requirements § 250.463 Who establishes field drilling rules? (a) The District Manager...

  15. Multi-state autonomous drilling for lunar exploration

    Institute of Scientific and Technical Information of China (English)

    Chen Chongbin; Quan Qiquan; Shi Xiaomeng; Deng Zongquan; Tang Dewei; Jiang Shengyuan

    2016-01-01

    Due to the lack of information of subsurface lunar regolith stratification which varies along depth, the drilling device may encounter lunar soil and lunar rock randomly in the drilling process. To meet the load safety requirements of unmanned sampling mission under limited orbital resources, the control strategy of autonomous drilling should adapt to the indeterminable lunar environments. Based on the analysis of two types of typical drilling media (i.e., lunar soil and lunar rock), this paper proposes a multi-state control strategy for autonomous lunar drilling. To represent the working circumstances in the lunar subsurface and reduce the complexity of the control algo-rithm, lunar drilling process was categorized into three drilling states:the interface detection, initi-ation of drilling parameters for recognition and drilling medium recognition. Support vector machine (SVM) and continuous wavelet transform were employed for the online recognition of dril-ling media and interface, respectively. Finite state machine was utilized to control the transition among different drilling states. To verify the effectiveness of the multi-state control strategy, drilling experiments were implemented with multi-layered drilling media constructed by lunar soil simulant and lunar rock simulant. The results reveal that the multi-state control method is capable of detect-ing drilling state variation and adjusting drilling parameters timely under vibration interferences. The multi-state control method provides a feasible reference for the control of extraterrestrial autonomous drilling.

  16. Multi-state autonomous drilling for lunar exploration

    Directory of Open Access Journals (Sweden)

    Chen Chongbin

    2016-10-01

    Full Text Available Due to the lack of information of subsurface lunar regolith stratification which varies along depth, the drilling device may encounter lunar soil and lunar rock randomly in the drilling process. To meet the load safety requirements of unmanned sampling mission under limited orbital resources, the control strategy of autonomous drilling should adapt to the indeterminable lunar environments. Based on the analysis of two types of typical drilling media (i.e., lunar soil and lunar rock, this paper proposes a multi-state control strategy for autonomous lunar drilling. To represent the working circumstances in the lunar subsurface and reduce the complexity of the control algorithm, lunar drilling process was categorized into three drilling states: the interface detection, initiation of drilling parameters for recognition and drilling medium recognition. Support vector machine (SVM and continuous wavelet transform were employed for the online recognition of drilling media and interface, respectively. Finite state machine was utilized to control the transition among different drilling states. To verify the effectiveness of the multi-state control strategy, drilling experiments were implemented with multi-layered drilling media constructed by lunar soil simulant and lunar rock simulant. The results reveal that the multi-state control method is capable of detecting drilling state variation and adjusting drilling parameters timely under vibration interferences. The multi-state control method provides a feasible reference for the control of extraterrestrial autonomous drilling.

  17. OPTIMIZATION OF INFILL DRILLING IN NATURALLY-FRACTURED TIGHT-GAS RESERVOIRS

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence W. Teufel; Her-Yuan Chen; Thomas W. Engler; Bruce Hart

    2004-05-01

    A major goal of industry and the U.S. Department of Energy (DOE) fossil energy program is to increase gas reserves in tight-gas reservoirs. Infill drilling and hydraulic fracture stimulation in these reservoirs are important reservoir management strategies to increase production and reserves. Phase II of this DOE/cooperative industry project focused on optimization of infill drilling and evaluation of hydraulic fracturing in naturally-fractured tight-gas reservoirs. The cooperative project involved multidisciplinary reservoir characterization and simulation studies to determine infill well potential in the Mesaverde and Dakota sandstone formations at selected areas in the San Juan Basin of northwestern New Mexico. This work used the methodology and approach developed in Phase I. Integrated reservoir description and hydraulic fracture treatment analyses were also conducted in the Pecos Slope Abo tight-gas reservoir in southeastern New Mexico and the Lewis Shale in the San Juan Basin. This study has demonstrated a methodology to (1) describe reservoir heterogeneities and natural fracture systems, (2) determine reservoir permeability and permeability anisotropy, (3) define the elliptical drainage area and recoverable gas for existing wells, (4) determine the optimal location and number of new in-fill wells to maximize economic recovery, (5) forecast the increase in total cumulative gas production from infill drilling, and (6) evaluate hydraulic fracture simulation treatments and their impact on well drainage area and infill well potential. Industry partners during the course of this five-year project included BP, Burlington Resources, ConocoPhillips, and Williams.

  18. Percussive Augmenter of Rotary Drills for Operating as a Rotary-Hammer Drill

    Science.gov (United States)

    Aldrich, Jack Barron (Inventor); Bar-Cohen, Yoseph (Inventor); Sherrit, Stewart (Inventor); Badescu, Mircea (Inventor); Bao, Xiaoqi (Inventor); Scott, James Samson (Inventor)

    2014-01-01

    A percussive augmenter bit includes a connection shaft for mounting the bit onto a rotary drill. In a first modality, an actuator percussively drives the bit, and an electric slip-ring provides power to the actuator while being rotated by the drill. Hammering action from the actuator and rotation from the drill are applied directly to material being drilled. In a second modality, a percussive augmenter includes an actuator that operates as a hammering mechanism that drives a free mass into the bit creating stress pulses that fracture material that is in contact with the bit.

  19. Method of indicating the position of a drill head of a shaft drilling unit

    Energy Technology Data Exchange (ETDEWEB)

    Gudkov, G.D.; Fayner, L.B.; Gurerich, D.I.

    1982-01-01

    A method of indicating the position of a drill head of a shaft drilling unit consists of duplicating its position by an indicator which moves along with movement of the drill head during its forward and backward movements. In order to reduce time spent on auxilliary operations mismatching of the reading of the indicator and the position of the drill head is accomplished due to automatic rejection of the accumulated air during backward motion. The indicated mismatching is rejected at the end of the backward cycle.

  20. A self propelled drilling system for hard-rock, horizontal and coiled tube drilling

    Energy Technology Data Exchange (ETDEWEB)

    Biglin, D.; Wassell, M.

    1997-12-31

    Several advancements are needed to improve the efficiency and reliability of both hard rock drilling and extended reach drilling. This paper will present a Self Propelled Drilling System (SPDS) which can grip the borehole wall in order to provide a stable platform for the application of weight on bit (WOB) and resisting the reactive torque created by the downhole drilling motor, bit and formation interaction. The system will also dampen the damaging effects of drill string vibration. This tool employs two hydraulically activated anchors (front and rear) to grip the borehole wall, and a two-way thrust mandrel to apply both the drilling force to the bit, and a retraction force to pull the drill string into the hole. Forward drilling motion will commence by sequencing the anchor pistons and thrust mandrel to allow the tool to walk in a stepping motion. The SPDS has a microprocessor to control valve timing, sensing and communication functions. An optional Measurement While Drilling (MWD) interface can provide two-way communication of critical operating parameters such as hydraulic pressure and piston location. This information can then be telemetered to the surface, or used downhole to autonomously control system parameters such as anchor and thrust force or damping characteristics.