WorldWideScience

Sample records for delamination resistant composite

  1. Delamination of Composite Cylinders

    Science.gov (United States)

    Davies, Peter; Carlsson, Leif A.

    The delamination resistance of filament wound glass/epoxy cylinders has been characterized for a range of winding angles and fracture mode ratios using beam fracture specimens. The results reveal that the delamination fracture resistance increases with increasing winding angle and mode II (shear) fraction (GΠ/G). It was also found that interlaced fiber bundles in the filament wound cylinder wall acted as effective crack arresters in mode I loading. To examine the sensitivity of delamina-tion damage on the strength of the cylinders, external pressure tests were performed on filament-wound glass/epoxy composite cylinders with artificial defects and impact damage. The results revealed that the cylinder strength was insensitive to the presence of single delaminations but impact damage caused reductions in failure pressure. The insensitivity of the failure pressure to a single delamination is attributed to the absence of buckling of the delaminated sublaminates before the cylinder wall collapsed. The impacted cylinders contained multiple delaminations, which caused local reduction in the compressive load capability and reduction in failure pressure. The response of glass/epoxy cylinders was compared to impacted carbon reinforced cylinders. Carbon/epoxy is more sensitive to damage but retains higher implosion resistance while carbon/PEEK shows the opposite trend.

  2. Fractography of composite delamination

    Science.gov (United States)

    Bascom, W. D.

    1990-01-01

    The microdamage that occurs for Mode 1 and Mode 2 delamination was examined by potting delaminated specimens in a clear epoxy, sectioning through the damage, polishing the cut sections and examining using light microscopy. For Mode 1 delamination of unidirectional carbon fiber reinforced plastic (CFRP) composites, the major observation was fiber bridging including large ligaments of fiber bundles. The Mode 2 delamination of unidirectional laminates revealed a very narrow crack opening with only occasional fiber bridging. Impact testing by repetitive impacts with increasing energy was studied and it was found that this technique does not discern changes in the type of damage with increasing cumulative impact energy. Instead, the changes in the impact response, notably stiffness, are the result of changes in the extent of damage. For laminates with a brittle thermoplastic matrix, 3501-6, there were distinct changes in stiffness that corresponded to the development of through the thickness damage and then to the extension of the damage to the specimen edges. For PEEK and polycarbonate, the changes in stiffness were not as abrupt as for the thermoset. None the less, the damage progressed in the same manner.

  3. Assembly induced delaminations in composite structures

    Science.gov (United States)

    Goering, J.; Bohlmann, R.; Wanthal, S.; Kautz, E.; Neri, Lawrence M.

    1992-01-01

    Experimental and analytical studies of the development of delaminations around fastener holes in composite structures are presented. This type of delamination is known to occur in composite skins that are mechanically fastened to a poorly mating substructure. Results of an experimental study to determine the resistance of laminates to the initiation of assembly induced delaminations and the residual strength of assembly damaged coupons are presented for AS4/3501-6, IM7/8551-7A, and AS4/PEEK material systems. A survey of existing analytical models for predicting the residual strength and stability of delaminations is presented, and the development of a new model for predicting the initiation of delaminations around a fastener hole is outlined. The fastener hole damage initiation model utilizes a finite element based Fourier series solution, and is validated through comparisons of analytical and experimental results.

  4. Delamination tolerance studies in laminated composite panels

    Indian Academy of Sciences (India)

    K L Singh; B Dattaguru; T S Ramamurthy; P D Mangalgiri

    2000-08-01

    Determination of levels of tolerance in delaminated composite panels is an important issue in composite structures technology. The primary intention is to analyse delaminated composite panels and estimate Strain Energy Release Rate (SERR) parameters at the delamination front to feed into acceptability criteria. Large deformation analysis is necessary to cater for excessive rotational deformations in the delaminated sublaminate. Modified Virtual Crack Closure Integral (MVCCI) is used to estimate all the three SERR components at the delamination front from the finite element output containing displacements, strains and stresses. The applied loading conditions are particularly critical and compressive loading on the panel could lead to buckling of the delaminated sublaminate and consequent growth of delamination. Numerical results are presented for circular delamination of varioussizes and delamination at various interfaces (varying depth-wise location) between the base- and the sub-laminates. Numerical data are also presented on the effect of bi-axial loading and in particular on compressive loading in both directions. The results can be used to estimate delamination tolerance at various depths (or at various interfaces) in the laminate.

  5. Delamination toughness of ultra high molecular weight polyethylene (UHMWPE composites

    Directory of Open Access Journals (Sweden)

    Casas-Rodriguez J.P.

    2012-08-01

    Full Text Available Ultra high molecular weight polyethylene (UHMWPE fibre reinforced composites are an important group of material for armours solutions, where their unique combination of properties could be utilized. A commonly observed failure mode in this kind of unidirectional laminated composites under impact ballistic is delamination between the composite layers. In the present study, an investigation on the delamination toughness behaviour exhibited by UHMWPE composites laminated was made. The interlaminar Mode II critical strain energy release rates of (UHMWPE fibre reinforced composites were characterized using the End Notch Flexural (ENF test. Critical strain energy release rate was obtained from the load – deflection test data using the beam theory expression. It was found that the energy release rate of the composite exhibited a very low value of around 60J/m2 using a moulding pressure of approximately 1200 psi. In order to analyse the delamination resistance of composite, the effects of changing the manufacture process variables and the use of a thermoplastic adhesive film in the composites were investigated. The composite laminates were produced by hot compressing moulding using a film-stacking procedure. It was found that the damage resistance of the UHMWPE composite was influenced by the manufacture method, which affects the Mode II interlaminar fracture toughness and the ballistic response of composites.

  6. Characterization of delamination onset and growth in a composite laminate

    Science.gov (United States)

    Obrien, T. K.

    1981-01-01

    The onset and growth of delaminations in unnotched (+ or - 30/+ or - 30/90/90 bar) sub S graphite epoxy laminates is described quantitatively. These laminates, designed to delaminate at the edges under tensile loads, were tested and analyzed. Delamination growth and stiffness loss were monitored nondestructively. Laminate stiffness decreased linearly with delamination size. The strain energy release rate, G, associated with delamination growth, was calculated from two analyses. A critical G for delamination onset was determined, and then was used to predict the onset of delaminations in (+45 sub n/-45 sub n/o sub n/90 sub n) sub s (n=1,2,3) laminates. A delamination resistance curve (R curve) was developed to characterize the observed stable delamination growth under quasi static loading. A power law correlation between G and delamination growth rates in fatigue was established.

  7. Fiber Optic Thermal Detection of Composite Delaminations

    Science.gov (United States)

    Wu, Meng-Chou; Winfree, William P.

    2011-01-01

    A recently developed technique is presented for thermographic detection of delaminations in composites by performing temperature measurements with fiber optic Bragg gratings. A single optical fiber with multiple Bragg gratings employed as surface temperature sensors was bonded to the surface of a composite with subsurface defects. The investigated structure was a 10-ply composite specimen with prefabricated delaminations of various sizes and depths. Both during and following the application of a thermal heat flux to the surface, the individual Bragg grating sensors measured the temporal and spatial temperature variations. The data obtained from grating sensors were analyzed with thermal modeling techniques of conventional thermography to reveal particular characteristics of the interested areas. Results were compared and found to be consistent with the calculations using numerical simulation techniques. Also discussed are methods including various heating sources and patterns, and their limitations for performing in-situ structural health monitoring.

  8. Bending strength of delaminated aerospace composites.

    Science.gov (United States)

    Kinawy, Moustafa; Butler, Richard; Hunt, Giles W

    2012-04-28

    Buckling-driven delamination is considered among the most critical failure modes in composite laminates. This paper examines the propagation of delaminations in a beam under pure bending. A pre-developed analytical model to predict the critical buckling moment of a thin sub-laminate is extended to account for propagation prediction, using mixed-mode fracture analysis. Fractography analysis is performed to distinguish between mode I and mode II contributions to the final failure of specimens. Comparison between experimental results and analysis shows agreement to within 5 per cent in static propagation moment for two different materials. It is concluded that static fracture is almost entirely driven by mode II effects. This result was unexpected because it arises from a buckling mode that opens the delamination. For this reason, and because of the excellent repeatability of the experiments, the method of testing may be a promising means of establishing the critical value of mode II fracture toughness, G(IIC), of the material. Fatigue testing on similar samples showed that buckled delamination resulted in a fatigue threshold that was over 80 per cent lower than the static propagation moment. Such an outcome highlights the significance of predicting snap-buckling moment and subsequent propagation for design purposes.

  9. Compressive strength of delaminated aerospace composites.

    Science.gov (United States)

    Butler, Richard; Rhead, Andrew T; Liu, Wenli; Kontis, Nikolaos

    2012-04-28

    An efficient analytical model is described which predicts the value of compressive strain below which buckle-driven propagation of delaminations in aerospace composites will not occur. An extension of this efficient strip model which accounts for propagation transverse to the direction of applied compression is derived. In order to provide validation for the strip model a number of laminates were artificially delaminated producing a range of thin anisotropic sub-laminates made up of 0°, ±45° and 90° plies that displayed varied buckling and delamination propagation phenomena. These laminates were subsequently subject to experimental compression testing and nonlinear finite element analysis (FEA) using cohesive elements. Comparison of strip model results with those from experiments indicates that the model can conservatively predict the strain at which propagation occurs to within 10 per cent of experimental values provided (i) the thin-film assumption made in the modelling methodology holds and (ii) full elastic coupling effects do not play a significant role in the post-buckling of the sub-laminate. With such provision, the model was more accurate and produced fewer non-conservative results than FEA. The accuracy and efficiency of the model make it well suited to application in optimum ply-stacking algorithms to maximize laminate strength.

  10. Buckling and Delamination Growth Analysis of Composite Laminates Containing Embedded Delaminations

    Science.gov (United States)

    Hosseini-Toudeshky, H.; Hosseini, S.; Mohammadi, B.

    2010-04-01

    The objective of this work is to study the post buckling behavior of composite laminates, containing embedded delamination, under uniaxial compression loading. For this purpose, delamination initiation and propagation is modeled using the softening behavior of interface elements. The full layer-wise plate theory is also employed for approximating the displacement field of laminates and the interface elements are considered as a numerical layer between any two adjacent layers which delamination is expected to propagate. A finite element program was developed and the geometric non-linearity in the von karman sense is incorporated to the strain/displacement relations, to obtain the buckling behavior. It will be shown that, the buckling load, delamination growth process and buckling mode of the composite plates depends on the size of delamination and stacking sequence of the laminates.

  11. Mode Mixity for Orthotropic Interface Delamination in Laminated Composites

    Institute of Scientific and Technical Information of China (English)

    FAN Xue-ling; SUN Qin; YUAN Mei-ni; Masanori Kikuchi

    2009-01-01

    The mode mixity is defined based on nonoscillatory strain energy release rate components of delamination between two different orthotropic materials to evaluate the delamination behavior of laminated composites.The result showes that the relative location of the delamination through the thickness influences the mode mixity in a relatively well-regulated way,and that the reinforcement directions of the adjacent plies along the delamination front have a more complicated impact on the mode mixity.This is caused by the bending/twist coupling and bending/bending coupling in the stress field at the crack tip for delamination between multidirectional plies,which completely modifies the stress and strain fields ahead of the crack tip.These kinds of couplings account for the non-uniform distribution of mode mixity values along the delamination front.Application of appropriate mode mixity values is necessary for accurate prediction of delamination growth.

  12. FINITE ELEMENT IMPLEMENTATION OF DELAMINATION IN COMPOSITE PLATES

    Directory of Open Access Journals (Sweden)

    Milan Žmindák

    2012-12-01

    Full Text Available Modelling of composite structures by finite element (FE codes to effectively model certain critical failure modes such as delamination is limited. Previous efforts to model delamination and debonding failure modes using FE codes have typically relied on ad hoc failure criteria and quasi-static fracture data. Improvements to these modelling procedures can be made by using an approach based on fracture mechanics. A study of modelling delamination using the finite element code ANSYS was conducted. This investigation demonstrates the modelling of composites through improved delamination modelling. Further developments to this approach may be improved.

  13. Vibration of composite beams with two overlapping delaminations

    Institute of Scientific and Technical Information of China (English)

    Christian N. Della; Dongwei Shu; Yapu Zhao

    2005-01-01

    Delaminations in composite laminates may develop from small cracks due to fabrication and impact loading, or from places of high stress concentration. The locations of the delaminations are not determinate. In this research, an analytical solution for the free vibration of a composite beam with two overlapping delaminations is presented. The delaminated beam is analyzed as seven interconnected beams using the delaminations as their boundaries. The continuity and equilibrium conditions are satisfied between the adjoining regions of the beams. Classical beam theory is applied to each of the beams. Complex vibration behaviors emerge for different sizes and locations of the delaminations. Comparison with analytical results reported in the literature verifies the validity of the present solution.

  14. Experimental Vibration Study on the Healthy and Delaminated Composite Plates

    Energy Technology Data Exchange (ETDEWEB)

    Ullah, Israr; Sinha, Jyoti K, E-mail: Jyoti.Sinha@manchester.ac.uk [School of Mechanical, Aerospace and Civil Engineering, University of Manchester, Manchester M13 9PL (United Kingdom)

    2011-07-19

    Vibration based damage, in particular delamination detection, in the composite structures is an active research area. The present study is also on the dynamics of the composite plates with and without delamination based on the experimental study. The test plate made of E-glass fibre and epoxy resins has been used here. A piezo-electric shaker has been used to excite the composite plate and the acceleration responses were measured using the number of accelerometers. The dynamics of the delaminated composite plates were then compared with a healthy composite plate when the vibration experiments have been conducted at the lower modes. The paper will discuss the observations made on the measured vibration responses from both the healthy and the delaminated plates and the possibility of the delamination detection from the experimental vibration data.

  15. DELAMINATION FORMATION AND DELAMINATION PROPAGATION OF COMPOSITE LAMINATES UNDER COMPRESSIVE FATIGUE LOADING

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Fatigue tests of the smooth composite laminates and the notched composite laminates under compressive cyclic loading have been carried out. The damage mechanism is discussed and analyzed. Damage evolution is monitored using stiffness decay. From these tests, it is found that the initial delamination occurs at the free boundary of smooth specimens, or the notch boundary of notched specimens, subjected to the compression-compression cyclic load. A point of view in relation to two-phases of compression fatigue delamination of composites is proposed, namely, compression-compression delamination consists of the delamination formation phase and the delamination propagation, and there is a "damage transition point" to separate this two-phases. Furthermore, an empirical modulus degradation formula and its parameters fitting method are presented. According to the test data handling results, it is shown that this formula is univocal and can fit the test data conveniently. In addition, two kinds of new anti-buckling devices are designed for these tests. At last, the E-N curves, the D-N curves and the S-N curve of the smooth carbon fiber reinforced composite laminates of T300/648C are determined to predict the fatigue life of the notched composite laminate. And the E-N curve of the notched specimens at the given load ratio R=10 and minimum load P min=-0.45 kN is also measured to verify the estimated result of fatigue life.

  16. NUMERICAL ANALYSIS OF DELAMINATION GROWTH FOR STIFFENED COMPOSITE LAMINATED PLATES

    Institute of Scientific and Technical Information of China (English)

    白瑞祥; 陈浩然

    2004-01-01

    A study of postbuckling and delamination propagation behavior in delaminated stiffened composite plates was presented. A methodology was proposed for simulating the multi-failure responses, such as initial and postbuckling, delamination onset and propagation, etc. A finite element analysis was conducted on the basis of the Mindlin first order shear effect theory and the von-Krmn nonlinear deformation assumption. The total energy release rate used as the criteria of delamination growth was estimated with virtual crack closure technique (VCCT). A self-adaptive grid moving technology was adopted to model the delamination growth process. Moreover, the contact effect along delamination front was also considered during the numerical simulation process. By some numerical examples, the influence of distribution and location of stiffener, configuration and size of the delamination, boundary condition and contact effect upon the delamination growth behavior of the stiffened composite plates were investigated. The method and numerical conclusion provided should be of great value to engineers dealing with composite structures.

  17. Progressive delamination in polymer matrix composite laminates: A new approach

    Science.gov (United States)

    Chamis, C. C.; Murthy, P. L. N.; Minnetyan, L.

    1992-01-01

    A new approach independent of stress intensity factors and fracture toughness parameters has been developed and is described for the computational simulation of progressive delamination in polymer matrix composite laminates. The damage stages are quantified based on physics via composite mechanics while the degradation of the laminate behavior is quantified via the finite element method. The approach accounts for all types of composite behavior, laminate configuration, load conditions, and delamination processes starting from damage initiation, to unstable propagation, and to laminate fracture. Results of laminate fracture in composite beams, panels, plates, and shells are presented to demonstrate the effectiveness and versatility of this new approach.

  18. Investigating Delamination Migration in Composite Tape Laminates

    Science.gov (United States)

    Ratcliffe, James G.; DeCarvalho, Nelson V.

    2014-01-01

    A modification to a recently developed test specimen designed to investigate migration of a delamination between neighboring ply interfaces in tape laminates is presented. The specimen is a cross-ply laminated beam consisting of 40 plies with a polytetrafluoroethylene insert spanning part way along its length. The insert is located between a lower 0-degree ply (specimen length direction) and a stack of four 90-degree plies (specimen width direction). The modification involved a stacking sequence that promotes stable delamination growth prior to migration, and included a relocation of the insert from the specimen midplane to the interface between plies 14 and 15. Specimens were clamped at both ends onto a rigid baseplate and loaded on their upper surface via a piano hinge assembly, resulting in a predominantly flexural loading condition. Tests were conducted with the load-application point positioned at various locations along a specimen's span. This position affected the sequence of damage events during a test.

  19. Characterization of Multiple Delaminated Composite by Finite Element

    Directory of Open Access Journals (Sweden)

    SUDIP DEY

    2011-09-01

    Full Text Available In this paper, a finite element method is employed to investigate the natural frequencies of twisted rotating composite turbine blades subject to multiple delamination. The turbine blade is idealized as a shallow conical shell model with low aspect ratio. The formulation is based on Mindlin’s theory, QR iteration and multi-point constraint algorithm for moderate rotational speeds neglecting Coriolis effect. Computer codes are developed and the numerical results obtained for multiple delaminated graphite-epoxy cross-ply composite shallow conical shells are the first known non-dimensional frequencies for the type of analyses carried out here.

  20. Finite elements modeling of delaminations in composite laminates

    DEFF Research Database (Denmark)

    Gaiotti, m.; Rizzo, C.M.; Branner, Kim;

    2011-01-01

    The application of composite materials in many structures poses to engineers the problem to create reliable and relatively simple methods, able to estimate the strength of multilayer composite structures. Multilayer composites, like other laminated materials, suffer from layer separation, i.e., d...... by finite elements using different techniques. Results obtained with different finite element models are compared and discussed.......The application of composite materials in many structures poses to engineers the problem to create reliable and relatively simple methods, able to estimate the strength of multilayer composite structures. Multilayer composites, like other laminated materials, suffer from layer separation, i...... of the buckling strength of composite laminates containing delaminations. Namely, non-linear buckling and post-buckling analyses are carried out to predict the critical buckling load of elementary composite laminates affected by rectangular delaminations of different sizes and locations, which are modelled...

  1. Optimizing the delamination failure in bamboo fiber reinforced polyester composite

    Directory of Open Access Journals (Sweden)

    N. Abilash

    2016-01-01

    Full Text Available Delamination is represented to be the most prevalent failure in composite structures. The use of composites in the manufacturing sector plays a very important role in the industry in general. Moreover these materials have unique characteristics when analyzed separately from constituents which are a part of them. In this paper, a partially ecological composite was made, using natural fibers as reinforcement (bamboo fiber, in the polyester resin matrix to form a composite, seeking to improve the mechanical behavior among its class of materials. The characteristics of a composite material are determined by how it behaves while machining, Drilling is the most predominant machining process because of its cost effectiveness when compared with other processes. Obviously delamination is the major problem that is focused by many researchers while selecting drilling as the machining process in polymeric composites. This research mainly emphasizes on the critical parameters by varying its speed, feed, and diameter of the cutting tool, their contribution to delamination was analyzed. Reduced delaminations were identified by varying the speed and feed rate.

  2. Buckling induced delamination of graphene composites through hybrid molecular modeling

    Science.gov (United States)

    Cranford, Steven W.

    2013-01-01

    The efficiency of graphene-based composites relies on mechanical stability and cooperativity, whereby separation of layers (i.e., delamination) can severely hinder performance. Here we study buckling induced delamination of mono- and bilayer graphene-based composites, utilizing a hybrid full atomistic and coarse-grained molecular dynamics approach. The coarse-grain model allows exploration of an idealized model material to facilitate parametric variation beyond any particular molecular structure. Through theoretical and simulation analyses, we show a critical delamination condition, where ΔD∝kL4, where ΔD is the change in bending stiffness (eV), k the stiffness of adhesion (eV/Å4), and L the length of the adhered section (Å).

  3. Buckling-driven delamination growth in composite laminates: Guidelines for assessing the threat posed by interlaminar matrix delamination

    DEFF Research Database (Denmark)

    Bhushan, Karihaloo; Stang, Henrik

    2008-01-01

    This paper is concerned with development of a simple procedure to assess the threat posed by interlaminar matrix delaminations to the integrity of composite laminates when they are situated in a compressive stress field. Depending upon the size of the delamination, its location below the surface...

  4. Delamination and debonding failure of laminated composite T-joints

    NARCIS (Netherlands)

    Cui, H.

    2014-01-01

    Composites are increasingly being used in aerospace, automotive and other industries. The T-joint (also named stringer stiffened skin) is a typical connection, broadly used in thin-walled structures, such as the wing and fuselage of aircraft. This thesis presents the analysis of the delamination and

  5. DETECTION OF DELAMINATION IN A COMPOSITE PLATE BY SEM

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A numerical method of integration of Green's functi ons of strip element method (SEM) is proposed. The response of ultrasonic sourc e generated by a transducer on the surface of a multi-ply composite plate conta ining a delamination is analyzed by the use of SEM. The numerical results show that the scanning features of the ultrasonic waves may be used to identify the d elamination inside the composite plate .

  6. Delamination Growth in Composites under Fatigue Loading

    NARCIS (Netherlands)

    Khan, R.

    2013-01-01

    Fiber reinforced composites are attractive for aerospace applications due to high specific strength and stiffness. Their use has been gradually increased to 50% by weight of the aircraft over past decades. As a consequence, modern aircraft utilize composites in the primary structures like wing skin

  7. Delamination Growth in Composites under Fatigue Loading

    NARCIS (Netherlands)

    Khan, R.

    2013-01-01

    Fiber reinforced composites are attractive for aerospace applications due to high specific strength and stiffness. Their use has been gradually increased to 50% by weight of the aircraft over past decades. As a consequence, modern aircraft utilize composites in the primary structures like wing skin

  8. Effects of Delaminations on the Damped Dynamic Characteristics of Composite Laminates: Mechanics and Experiments

    Science.gov (United States)

    Saravanos, D. A.; Hopkins, D. A.

    1995-01-01

    Analytical and experimental work is presented on the damped free-vibration of delaminated laminates and beams. A laminate theory is developed where the unknown kinematic perturbations induced by a delamination crack are treated as additional degrees of freedom. The generalized stiffness, inertia and damping matrices of the laminate are formulated. An analytical solution is developed for the prediction of natural frequencies, modes and modal damping in composite beams with delamination cracks. Evaluations of the mechanics on various cantilever beams with a central delamination are performed. Experimental results for the modal frequencies and damping of composite beams with a single delamination are also presented and correlations between analytical predictions and measured data are shown. The effects of delamination vary based on crack size, laminate configuration, and mode order. The implications of the mechanics in developing delamination detection techniques are also discussed.

  9. Impact Analysis of Embedded Delamination Location in Hybrid Curved Laminated Composite Stiffened Panel

    Science.gov (United States)

    Naini, Jeevan Kumar; P, Ramesh Babu

    2016-08-01

    Modern, aero structures are predominantly of curved construction characterized by a skin and stiffeners. The latest generation of large passenger aircraft also uses mostly composite material in their primary structure and there is trend towards the utilization of bonding of subcomponents. The presence of delamination is a major problem in composite laminated panels and so, it is of great concern to both the academic and aeronautical industrial worlds Indeed delamination can strongly affect the material strength and, sometimes, can cause their breaking up in service. A Pre-damaged configuration is loaded to study the delamination location and mode for delamination initiation and propagation. A parametric study is conducted to investigate the effect of the location of the delamination propagation when delamination is embedded inbetween plies of the skin-stiffener interface, with the cases i) delamination located at front and inbetween plies of the skin-stiffener interface ii) delamination located in middle and inbetween plies of the skin-stiffener interface iii) delamination located at the end and inbetween plies of the skin- stiffener interface. Further the influence of the location of the delamination on load carrying capacity of the panel is investigated. The effect of location of debonds on crack growth and collapse behavior is analyzed using analysis tool. An analysis tool is applied that includes an approach for predicting interlaminar damage initiation and interlaminar damage growth as well as in-plane damage mechanisms to predict the design of defect free panel.

  10. Low-velocity Impact Damage Analysis of Composite Laminates Using Self-adapting Delamination Element Method

    Institute of Scientific and Technical Information of China (English)

    Wang Lipeng; Yan Ying; Wu Dafang; Wu Hao

    2008-01-01

    On the basis of a 2D 4-node Mindlin shell element method, a novel self-adapting delamination finite element method is presented,which is developed to model the delamination damage of composite laminates. In the method, the sublaminate elements are generated automatically when the delamination damage occurs or extends. Thus, the complex process and state of delamination damage can be simulated practically with high efficiency for both analysis and modeling. Based on the self-adapting delamination method, linear dynamic finite element damage analysis is performed to simulate the low-velocity impact damage process of three types of mixed woven composite laminates. Taking the frictional force among sublaminations during delaminating and the transverse normal stress into account,the analytical results ate consistent with those of the experimental data.

  11. STUDY ON FAILURE PROCESS OF DELAMINATED STIFFENED COMPOSITE PLATES UNDER COMPRESSION

    Institute of Scientific and Technical Information of China (English)

    陈浩然; 白瑞祥; 王蔓

    2003-01-01

    Failure behavior of the delaminated stiffened composite plates under compression is studied by the finite element method, based on a Global-Local variational model. A virtual crack closure technique and a self-adaptive grid moving scheme are proposed to predict the delamination growth process. The contact effect along the delamination front is considered. The numerical results show that the influences of the distribution and location of the stiffeners, the configuration and size of the delamination, the boundary condition and the contact upon the failure behavior of the plates are significant.

  12. Characterization of Mode I and Mode II delamination growth and thresholds in AS4/PEEK composites

    Science.gov (United States)

    Martin, Roderick H.; Murri, Gretchen Bostaph

    1990-01-01

    Composite materials often fail by delamination. The onset and growth of delamination in AS4/PEEK, a tough thermoplastic matrix composite, was characterized for mode 1 and mode 2 loadings, using the Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) test specimens. Delamination growth per fatigue cycle, da/dN, was related to strain energy release rate, G, by means of a power law. However, the exponents of these power laws were too large for them to be adequately used as a life prediction tool. A small error in the estimated applied loads could lead to large errors in the delamination growth rates. Hence strain energy release rate thresholds, G sub th, below which no delamination would occur were also measured. Mode 1 and 2 threshold G values for no delamination growth were found by monitoring the number of cycles to delamination onset in the DCB and ENF specimens. The maximum applied G for which no delamination growth had occurred until at least 1,000,000 cycles was considered the threshold strain energy release rate. Comments are given on how testing effects, facial interference or delamination front damage, may invalidate the experimental determination of the constants in the expression.

  13. Characterization of Mode 1 and Mode 2 delamination growth and thresholds in graphite/peek composites

    Science.gov (United States)

    Martin, Roderick H.; Murri, Gretchen B.

    1988-01-01

    Composite materials often fail by delamination. The onset and growth of delamination in AS4/PEEK, a tough thermoplastic matrix composite, was characterized for mode 1 and mode 2 loadings, using the Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) test specimens. Delamination growth per fatigue cycle, da/dN, was related to strain energy release rate, G, by means of a power law. However, the exponents of these power laws were too large for them to be adequately used as a life prediction tool. A small error in the estimated applied loads could lead to large errors in the delamination growth rates. Hence strain energy release rate thresholds, G sub th, below which no delamination would occur were also measured. Mode 1 and 2 threshold G values for no delamination growth were found by monitoring the number of cycles to delamination onset in the DCB and ENF specimens. The maximum applied G for which no delamination growth had occurred until at least 1,000,000 cycles was considered the threshold strain energy release rate. Comments are given on how testing effects, facial interference or delamination front damage, may invalidate the experimental determination of the constants in the expression.

  14. Buckling of composite beams with two enveloped delaminations: Lower and upper bounds

    NARCIS (Netherlands)

    Parlapalli, M.S.R.; Shu, Dongwei; Chai, Gin B.

    2008-01-01

    Lower and upper bounds of the buckling load of a composite beam with two enveloped delaminations are obtained from newly developed analytical models. The characteristic equation, governing the delamination buckling is derived by using Euler–Bernoulli beam and classical lamination theory, performing

  15. Delamination growth behavior in cross-ply composites under compressive cyclic (fatigue) loading

    Science.gov (United States)

    Pelegri, Assimina A.

    A mode dependent fatigue delamination growth law for anisotropic composite plates is presented in this thesis. The novelty of the presented law lies in the mode dependency of the material and laminate constants m(Psi) and C(Psi). The model describing the mode dependent delamination growth law consists of an initial postbuckling solution accounting for general delaminated composites, i.e. with no restrictive assumptions on the delamination dimensions, and a fracture mechanics solution. A numerical code was developed for the implementation of the closed form solution which gives the loading and geometrical quantities as well as the energy release rates and the mode mixities. The computer code was especially designed for parametric studies. Parameters assigned in this particular investigation were: end conditions, delamination position (h/T), and applied strain. The effect of the end conditions, i.e. clamped-clamped versus simply-supported ends on the initial postbuckling and growth behavior of delaminated plates was also investigated. In conjunction with the previous analysis, a detailed experimental study was designed and carried out in order to validate the proposed model. The tests were designed so that the effect of certain parameters on the delamination growth behavior could be evaluated. The parameters included in the investigation were: initial delamination length, applied strain and delamination position (h/T). Compressive static, compressive fatigue (constant displacement amplitude), and double cantilever beam (DCB) tests were conducted. Data acquisition and analysis for these tests were performed. By comparing analytical and experimental results it is shown that a very good correlation exists, and the presented mode dependent fatigue delamination growth law can accurately predict fatigue lives of delaminated composite structures.

  16. Numerical and experimental studies of delamination detection in short fiber reinforced composites using Lamb waves

    Science.gov (United States)

    Kudela, Pawel; Radzienski, Maciej; Ostachowicz, Wieslaw

    2016-04-01

    The aim of this paper is to present aspects of Lamb wave propagation in randomly oriented short fiber reinforce composites with delamination. Prediction of elastic constants is based on mechanics of composites, rule of mixture and total mass balance tailored to the spectral element mesh composed of 3D brick elements. Piezoelectric excitation as well as glue layer are taken into account. Complex full wave field includes multiple reflections at short fibers. This wave pattern is also obtained by the use of laser vibrometry confirming good quality of the model. Further studies are related to symmetrical and non-symmetrical delamination in respect to the thickness of the composite plate. Square delamination of the side length 10 mm is investigated. It has been found that reflections from delamination are mostly superimposed with reflections coming from short fibers. Hence, delamination detection by direct analysis of wave propagation pattern on the surface of the plate is ineffective. However, adaptive wavenumber filtering method overcome these difficulties and enables not only to detect the delamination but also is helpful for delamination size estimation. Moreover, the method is more effective if the full wavefield measurements are acquired on the surface of the plate which is closer to the delamination.

  17. Compressive behavior of composite panels with deeply embedded delamination%Compressive behavior of composite panels with deeply embedded delamination

    Institute of Scientific and Technical Information of China (English)

    FU Hui-min; PENG Bo

    2012-01-01

    The compressive behavior of laminates with a deeply embedded circular delamination was studied numerically and experimentally.In the finite element analysis(FEA),virtual crack closure technique(VCCT) and B-K law were employed to simulate the delamination growth,and the contact of the two substrates was considered.The effect of the delamination size and through-thickness position on the compressive behavior of laminates with an artificially embedded circular delamination was discussed.It is found that the through-thickness position affects the buckling mode,which then strongly influences delamination growth speed and direction,as well as the dominant component energy release rate(ERR).The numerical results agreed well with the experimental results.

  18. Mode I fatigue delamination growth in composite laminates with fibre bridging

    NARCIS (Netherlands)

    Yao, L.

    2015-01-01

    Advanced composite materials have been commonly used in aerospace engineering, because of their good mechanical properties and attractive potential for creating lightweight structures. Susceptibility to delamination is one of the most important issues in the applications of these materials. This

  19. Interaction of Guided Lamb Waves with Delaminations and Discontinuities in Composite Plate-Like Structures

    Science.gov (United States)

    Balasubramaniam, Krishnan; Ramadas, C.; Padiyar, Janardhan; Krishnamurthy, C. V.

    2011-06-01

    Delamination is one of the critical failure modes that laminated composites structures encounter during their fabrication and/or in-service. When guided Lamb wave (Ao) is employed for sizing of delamination, it is necessary to understand the wave interaction with the defect. Studies were carried out on the interaction of Ao mode with symmetric and asymmetric delaminations and transmission of turning modes in the sub-laminates. An attempt was also made to understand the propagation of Ao mode in composite structural T-joint. During the interaction of Ao mode with structural discontinuity in a T-joint, generation of a new mode, So, and propagation of turning modes were observed. Length and width of interface delamination in composite T-joint have been worked out using D-scan and B-scan respectively. All studied were carried out through numerical simulations and experimental verifications through Non- Contact Ultrasound (NCU) technique.

  20. Application of the Refined Zigzag Theory to the Modeling of Delaminations in Laminated Composites

    Science.gov (United States)

    Groh, Rainer M. J.; Weaver, Paul M.; Tessler, Alexander

    2015-01-01

    The Refined Zigzag Theory is applied to the modeling of delaminations in laminated composites. The commonly used cohesive zone approach is adapted for use within a continuum mechanics model, and then used to predict the onset and propagation of delamination in five cross-ply composite beams. The resin-rich area between individual composite plies is modeled explicitly using thin, discrete layers with isotropic material properties. A damage model is applied to these resin-rich layers to enable tracking of delamination propagation. The displacement jump across the damaged interfacial resin layer is captured using the zigzag function of the Refined Zigzag Theory. The overall model predicts the initiation of delamination to within 8% compared to experimental results and the load drop after propagation is represented accurately.

  1. Detection of drilling-induced delamination in aeronautical composites by noncontact laser ultrasonic method.

    Science.gov (United States)

    Zhou, Zhenggan; Sun, Guangkai; Chen, Xiucheng; Wang, Jie

    2014-04-20

    A novel application of the laser ultrasonic technique for the detection of drilling-induced delamination in composite components of aircrafts is proposed. Numerous key components of aircrafts are made of composite materials, and drilling is often a final operation during assembly. Drilling-induced delamination significantly reduces the structural reliability, and it is rather difficult to be detected effectively and automatically. The laser ultrasonic technique is a promising method to solve the problem. This paper investigates the characterization of drilling-induced delamination in composites by a noncontact laser ultrasonic method. A carbon fiber reinforced plastic laminate with drilling holes is prepared as a specimen. The characterization of drilling-induced delamination with laser-generated ultrasonic waves is investigated theoretically and experimentally, and the morphology features of the delamination are obtained by laser ultrasonic C-scan testing. The results prove that the laser ultrasonic technique is effective for the detection of drilling-induced delamination in composite components, and it is a feasible solution for evaluating the drilling quality during assembly.

  2. Scattering of the fundamental anti-symmetric Lamb wave at delaminations in composite laminates.

    Science.gov (United States)

    Ng, Ching-Tai; Veidt, Martin

    2011-03-01

    An analysis of the scattering characteristics of the fundamental anti-symmetric (A(0)) Lamb wave at a delamination in a quasi-isotropic composite laminate is presented. Analytical solutions for this problem do not exist due to the anisotropic nature and multilayer characteristics of composite laminates. This study uses a three-dimensional finite element (FE) method and experimental measurements to provide physical insight into the scattering phenomena. Good agreement is found between simulations and experimental measurements. The results show that the A(0) Lamb wave scattering at a delamination in composite laminates is much more complicated than the scattering at a defect in isotropic plates. Scatter amplitudes and scatter directivity distributions depend on the delamination size to wavelength ratio and the through-thickness location of the delamination damage. The study also investigates the feasibility of the common experimental practice of simulating delamination damage by bonding masses to the surface of composite laminates for guided wave damage detection and characterization methodologies verifications. The results suggest that care is required to use bonded masses to simulate delamination damage for verifying and optimizing damage characterization techniques. In summary, the results of the investigation help to further advance the use of the A(0) Lamb wave for damage detection and characterization.

  3. Failure analysis of multiple delaminated composite plates due to bending and impact

    Indian Academy of Sciences (India)

    P K Parhi; S K Bhattacharyya; P K Sinha

    2001-04-01

    The present work aims at the first ply failure analysis of laminated composite plates with arbitrarily located multiple delaminations subjected to transverse static load as well as impact. The theoretical formulation is based on a simple multiple delamination model. Conventional first order shear deformation is assumed using eight-noded isoparametric quadratic elements to develop the finite element analysis procedure. Composite plates are assumed to contain both single and multiple delaminations. For the case of impact, Newmark time integration algorithm is employed for solving the time dependent multiple equations of the plate and the impactor. Tsai-Wu failure criterion is used to check for failure of the laminate for both the cases. To investigate the first ply failure, parametric studies are made for different cases by varying the size and number of delaminations as well as the stacking sequences and boundary conditions.

  4. Dynamic buckling analysis of delaminated composite plates using semi-analytical finite strip method

    Science.gov (United States)

    Ovesy, H. R.; Totounferoush, A.; Ghannadpour, S. A. M.

    2015-05-01

    The delamination phenomena can become of paramount importance when the design of the composite plates is concerned. In the current study, the effect of through-the-width delamination on dynamic buckling behavior of a composite plate is studied by implementing semi-analytical finite strip method. In this method, the energy and work integrations are computed analytically due to the implementation of trigonometric functions. Moreover, the method can lead to converged results with comparatively small number of degrees of freedom. These features have made the method quite efficient. To account for delamination effects, displacement field is enriched by adding appropriate terms. Also, the penetration of the delamination surfaces is prevented by incorporating an appropriate contact scheme into the time response analysis. Some selected results are validated against those available in the literature.

  5. Detection of Delamination in Composite Beams Using Broadband Acoustic Emission Signatures

    Science.gov (United States)

    Okafor, A. C.; Chandrashekhara, K.; Jiang, Y. P.

    1996-01-01

    Delamination in composite structure may be caused by imperfections introduced during the manufacturing process or by impact loads by foreign objects during the operational life. There are some nondestructive evaluation methods to detect delamination in composite structures such as x-radiography, ultrasonic testing, and thermal/infrared inspection. These methods are expensive and hard to use for on line detection. Acoustic emission testing can monitor the material under test even under the presence of noise generated under load. It has been used extensively in proof-testing of fiberglass pressure vessels and beams. In the present work, experimental studies are conducted to investigate the use of broadband acoustic emission signatures to detect delaminations in composite beams. Glass/epoxy beam specimens with full width, prescribed delamination sizes of 2 inches and 4 inches are investigated. The prescribed delamination is produced by inserting Teflon film between laminae during the fabrication of composite laminate. The objectives of this research is to develop a method for predicting delamination size and location in laminated composite beams by combining smart materials concept and broadband AE analysis techniques. More specifically, a piezoceramic (PZT) patch is bonded on the surface of composite beams and used as a pulser. The piezoceramic patch simulates the AE wave source as a 3 cycles, 50KHz, burst sine wave. One broadband AE sensor is fixed near the PZT patch to measure the AE wave near the AE source. A second broadband AE sensor, which is used as a receiver, is scanned along the composite beams at 0.25 inch step to measure propagation of AE wave along the composite beams. The acquired AE waveform is digitized and processed. Signal strength, signal energy, cross-correlation of AE waveforms, and tracking of specific cycle of AE waveforms are used to detect delamination size and location.

  6. On the Through-the-Width Multiple Delamination, and Buckling and Postbuckling Behaviors of Symmetric and Unsymmetric Composite Laminates

    Science.gov (United States)

    Liu, P. F.; Zheng, J. Y.

    2013-12-01

    Multiple delamination causes severe degradation of the stiffness and strength of composites. Interactions between multiple delamination, and buckling and postbuckling under compressive loads add the complexity of mechanical properties of composites. In this paper, the buckling, postbuckling and through-the-width multiple delamination of symmetric and unsymmetric composite laminates are studied using 3D FEA, and the virtual crack closure technique with two delamination failure criteria: B-K law and power law is used to predict the delamination growth and to calculate the mixed-mode energy release rate. The compressive load-strain curves, load-central deflection curves and multiple delamination process for eight composite specimens with different initial delamination sizes and their distributions as well as two angle-ply configurations 04//(± θ)6//04 ( θ = 0° and 45°, and "//" denotes the delaminated interface) are comparatively studied. From numerical results, the unsymmetry decreases the local buckling load and initial delamination load, but does not affect the global buckling load compared with the symmetric laminates. Besides, the unsymmetry affects the unstable delamination and buckling behaviors of composite laminates largely when the initial multiple delamination sizes are relatively small.

  7. Delamination detection in composite laminates using dispersion change based on mode conversion of Lamb waves

    Science.gov (United States)

    Okabe, Yoji; Fujibayashi, Keiji; Shimazaki, Mamoru; Soejima, Hideki; Ogisu, Toshimichi

    2010-11-01

    A new ultrasonic propagation system has been constructed using macrofiber composite (MFC) actuators and fiber Bragg grating (FBG) sensors. The MFCs and FBGs can be integrated into composite laminates because of their small size and high fracture strain. The developed system can send and receive broadband Lamb waves. In this research, this system was used to detect delamination damage in composite laminates. First, the multiple modes of Lamb waves in a carbon-fiber-reinforced plastic (CFRP) quasi-isotropic laminate were identified by transmitting and receiving the symmetric and antisymmetric modes separately. Then, the mode conversions at both tips of a delamination were investigated through an experiment and a two-dimensional finite element analysis (FEA). A new delamination detection method was proposed on the basis of the mode conversions, and experiments were carried out on laminates with an artificial delamination. When antisymmetric modes were excited, the frequency dispersion of the received A1 mode changed, depending on the delamination length owing to the mode conversion between the A1 mode and the S0 mode. This phenomenon was confirmed through the FEA and these results prove that this new method is effective in detecting a delamination in CFRP laminates.

  8. Numerical investigation of nonlinear interactions between multimodal guided waves and delamination in composite structures

    Science.gov (United States)

    Shen, Yanfeng

    2017-04-01

    This paper presents a numerical investigation of the nonlinear interactions between multimodal guided waves and delamination in composite structures. The elastodynamic wave equations for anisotropic composite laminate were formulated using an explicit Local Interaction Simulation Approach (LISA). The contact dynamics was modeled using the penalty method. In order to capture the stick-slip contact motion, a Coulomb friction law was integrated into the computation procedure. A random gap function was defined for the contact pairs to model distributed initial closures or openings to approximate the nature of rough delamination interfaces. The LISA procedure was coded using the Compute Unified Device Architecture (CUDA), which enables the highly parallelized computation on powerful graphic cards. Several guided wave modes centered at various frequencies were investigated as the incident wave. Numerical case studies of different delamination locations across the thickness were carried out. The capability of different wave modes at various frequencies to trigger the Contact Acoustic Nonlinearity (CAN) was studied. The correlation between the delamination size and the signal nonlinearity was also investigated. Furthermore, the influence from the roughness of the delamination interfaces was discussed as well. The numerical investigation shows that the nonlinear features of wave delamination interactions can enhance the evaluation capability of guided wave Structural Health Monitoring (SHM) system. This paper finishes with discussion, concluding remarks, and suggestions for future work.

  9. Characterization of Delaminations and Transverse Matrix Cracks in Composite Laminates Using Multiple-Angle Ultrasonic Inspection

    Science.gov (United States)

    Johnston, Patrick H.; Appleget, Chelsea D.; Odarczenko, Michael T.

    2012-01-01

    Delaminations and transverse matrix cracks often appear concurrently in composite laminates. Normal-incidence ultrasound is excellent at detecting delaminations, but is not optimum for matrix cracks. Non-normal incidence, or polar backscattering, has been shown to optimally detect matrix cracks oriented perpendicular to the ultrasonic plane of incidence. In this work, a series of six composite laminates containing slots were loaded in tension to achieve various levels of delamination and ply cracking. Ultrasonic backscattering was measured over a range of incident polar and azimuthal angles, in order to characterize the relative degree of damage of the two types. Sweptpolar- angle measurements were taken with a curved phased array, as a step toward an array-based approach to simultaneous measurement of combined flaws.

  10. A Damage Model for the Simulation of Delamination in Advanced Composites under Variable-Mode Loading

    Science.gov (United States)

    Turon, A.; Camanho, P. P.; Costa, J.; Davila, C. G.

    2006-01-01

    A thermodynamically consistent damage model is proposed for the simulation of progressive delamination in composite materials under variable-mode ratio. The model is formulated in the context of Damage Mechanics. A novel constitutive equation is developed to model the initiation and propagation of delamination. A delamination initiation criterion is proposed to assure that the formulation can account for changes in the loading mode in a thermodynamically consistent way. The formulation accounts for crack closure effects to avoid interfacial penetration of two adjacent layers after complete decohesion. The model is implemented in a finite element formulation, and the numerical predictions are compared with experimental results obtained in both composite test specimens and structural components.

  11. Dynamic behavior of a rotating delaminated composite beam including rotary inertia and shear deformation effects

    Directory of Open Access Journals (Sweden)

    Ramazan-Ali Jafari-Talookolaei

    2015-09-01

    Full Text Available A finite element (FE model is developed to study the free vibration of a rotating laminated composite beam with a single delamination. The rotary inertia and shear deformation effects, as well as the bending–extension, bending–twist and extension–twist coupling terms are taken into account in the FE model. Comparison between the numerical results of the present model and the results published in the literature verifies the validity of the present model. Furthermore, the effects of various parameters, such as delamination size and location, fiber orientation, hub radius, material anisotropy and rotating speed, on the vibration of the beam are studied in detail. These results provide useful information in the study of the free vibration of rotating delaminated composite beams.

  12. Non-destructive evaluation of delamination growth in glass fiber composites using optical coherence tomography

    Science.gov (United States)

    Liu, Ping; Groves, Roger M.; Benedictus, Rinze

    2014-03-01

    Based on low coherence interferometry, a robust optical coherence tomography (OCT) system has been built. The system was used to monitor the growth of a delamination between the middle layers of a glass fiber composite under a static loading. Firstly specimens of the material used for the spar webs in wind turbines were prepared with an interlaminar crack from free edges. Then they were statically loaded by a customized tensile test stage to extend the delamination length and simultaneously scanned by the OCT system. To process the acquired data, an optimized signal processing algorithm was developed. The cross-sectional images clearly show the microstructure and the crack within the specimen. The 3D crack profiles show the application of OCT to determine the evolution of the crack structure inside the composite material during the propagation of the delamination, for the first time to the best of our knowledge.

  13. Mode I fatigue delamination growth in composite laminates with fibre bridging

    NARCIS (Netherlands)

    Yao, L.

    2015-01-01

    Advanced composite materials have been commonly used in aerospace engineering, because of their good mechanical properties and attractive potential for creating lightweight structures. Susceptibility to delamination is one of the most important issues in the applications of these materials. This dis

  14. Estimation of Local Delamination Buckling in Orthotropic Composite Plates Using Kirchhoff Plate Finite Elements

    Directory of Open Access Journals (Sweden)

    Zoltán Juhász

    2015-01-01

    Full Text Available We analyse the buckling process of composite plates with through-the-width delamination and straight crack front applying uniaxial compression. We are focusing on the mixed mode buckling case, where the non-uniform distribution of the in-plane forces controls the occurence of the buckling of the delaminated layers. For the analysis, semi-discrete finite elements will be derived based on the Lèvy-type method. The method of harmonic balance is used for taking into account the force distribution that is generally non uniform in-plane.

  15. Preliminary study on occurrence of composite material delamination processed by abrasive water jet cutting

    Directory of Open Access Journals (Sweden)

    Popan Ioan Alexandru

    2017-01-01

    Full Text Available The paper presents a preliminary experimental study on processing composite materials (CFRP using abrasive water jet cutting (AWJC process, analysing the possibilities of occurrence of material delamination. AWJC is a proper solution for cutting CFRP because of reduced interface temperature, high flexibility, low mechanical loading and reduced cutting forces. Cutting CFRP using AWJC involves several challenges like material delamination due to the high velocity impact of the jet. To understand the delamination, three experimental tests were made: in the first test the cutting and the drilling was made with high water pressure (350 MPa, in the second test the cutting was made with high water pressure and for drilling was used low water pressure (200 MPa and in last test a pre-drilled hole was used. Within those experiments was observed the CFRP delamination appears just during the drilling, not during the cutting. By decreasing the water jet pressure, the jet energy is decreased and in this way the delamination decrease.

  16. The Effect of Delamination on Damage Path and Failure Load Prediction for Notched Composite Laminates

    Science.gov (United States)

    Satyanarayana, Arunkumar; Bogert, Philip B.; Chunchu, Prasad B.

    2007-01-01

    The influence of delamination on the progressing damage path and initial failure load in composite laminates is investigated. Results are presented from a numerical and an experimental study of center-notched tensile-loaded coupons. The numerical study includes two approaches. The first approach considers only intralaminar (fiber breakage and matrix cracking) damage modes in calculating the progression of the damage path. In the second approach, the model is extended to consider the effect of interlaminar (delamination) damage modes in addition to the intralaminar damage modes. The intralaminar damage is modeled using progressive damage analysis (PDA) methodology implemented with the VUMAT subroutine in the ABAQUS finite element code. The interlaminar damage mode has been simulated using cohesive elements in ABAQUS. In the experimental study, 2-3 specimens each of two different stacking sequences of center-notched laminates are tensile loaded. The numerical results from the two different modeling approaches are compared with each other and the experimentally observed results for both laminate types. The comparisons reveal that the second modeling approach, where the delamination damage mode is included together with the intralaminar damage modes, better simulates the experimentally observed damage modes and damage paths, which were characterized by splitting failures perpendicular to the notch tips in one or more layers. Additionally, the inclusion of the delamination mode resulted in a better prediction of the loads at which the failure took place, which were higher than those predicted by the first modeling approach which did not include delaminations.

  17. A hybrid method based upon nonlinear Lamb wave response for locating a delamination in composite laminates.

    Science.gov (United States)

    Yelve, Nitesh P; Mitra, Mira; Mujumdar, P M; Ramadas, C

    2016-08-01

    A new hybrid method based upon nonlinear Lamb wave response in time and frequency domains is introduced to locate a delamination in composite laminates. In Lamb wave based nonlinear method, the presence of damage is shown by the appearance of higher harmonics in the Lamb wave response. The proposed method not only uses this spectral information but also the corresponding temporal response data, for locating the delamination. Thus, the method is termed as a hybrid method. The paper includes formulation of the method and its application to locate a Barely Visible Impact Damage (BVID) induced delamination in a Carbon Fiber Reinforced Polymer (CFRP) laminate. The method gives the damage location fairly well. It is a baseline free method, as it does not need data from the pristine specimen.

  18. Optical Evaluation on Delamination Buckling of Composite Laminate with Impact Damage

    Directory of Open Access Journals (Sweden)

    J. T. Ruan

    2014-01-01

    Full Text Available The delamination buckling and growth behaviors of a cross-ply composite laminate with damage induced by low velocity impact are investigated optically using three-dimensional digital image correlation (3D-DIC method. For the 3D deformation measurement, the 3D-DIC setup comprised of two CCD cameras was adopted. The rectangle specimen was impacted under the impact energy of 7.0 J using a drop-weight testing machine, and the impact damage was detected by means of X-ray nondestructive evaluation (NDE technique. The 3D deformation field measured with the optical system clearly reveals that the delamination buckling characteristic of the specimen mainly appears local deformation mode under compression after impact test. Moreover, the behavior of delamination growth evaluated by the 3D-DIC optical method reasonably agrees with the NDE observed damage result after compression.

  19. Finite element modeling of guided wave scattering at delaminations in composite panels

    Science.gov (United States)

    Murat, B. I. S.; Fromme, P.

    2016-04-01

    Carbon fiber laminate composites, consisting of layers of polymer matrix reinforced with high strength carbon fibers, are increasingly employed for aerospace structures. They offer advantages for aerospace applications, e.g., good strength to weight ratio. However, impact during the operation and servicing of the aircraft can lead to barely visible and difficult to detect damage. Depending on the severity of the impact, delaminations can occur, reducing the load carrying capacity of the structure. Efficient structural health monitoring of composite panels can be achieved using guided ultrasonic waves propagating along the structure. The guided ultrasonic wave (A0 Lamb wave mode) scattering at delaminations was modelled using full three-dimensional Finite Element (FE) simulations. The influence of the delamination size was systematically investigated from a parameter study. The angular dependency of the scattered guided wave amplitude was calculated using a baseline subtraction method. A significant influence of the delamination width on the guided wave scattering was found. The sensitivity of guided waves for the detection of barely visible impact damage in composite panels has been predicted.

  20. Modeling of 3D Woven Composites Containing Multiple Delaminations

    Science.gov (United States)

    2012-08-20

    researchers 3D woven composites shows better damage tolerance than laminated textile composites without z-yarns such as plain woven composites even...modeling of quasi-static short beam shear test of plain woven laminated composites. Cohesive elements were used in regions where transverse cracks and...Title ABSTRACT In this paper we present FE modeling of quasi-static short beam shear test of plain woven laminated composites. Cohesive elements were

  1. Coupled flexural-longitudinal vibration of delaminated composite beams with local stability analysis

    Science.gov (United States)

    Szekrényes, András

    2014-09-01

    A novel analytical model is developed to solve the problem of free vibration of delaminated composite beams. The beam with a single delamination was modelled by six equivalent single layers by establishing the kinematic continuity in the undelaminated portion of the system. In the delaminated region the layers were captured by the traditional theories. First, Timoshenko beam theory is applied to solve the problem, then by reducing the model, the corresponding Euler-Bernoulli solution is presented. Both the free and constrained models were considered. The most important aspect of the present analysis is that the beams of the delaminated region are subjected to normal forces, as well. That is the essential reason for leading to a coupled flexural-longitudinal vibration problem. It is also concluded that delamination buckling can take place if the normal force is compressive in one of the half-periods of the vibration and reaches a critical value. The problem was also investigated experimentally by modal hammer and sweep excitation tests on beams made of E-glass/polyester in order to measure the natural frequencies and mode shapes. The comparison of the analytical and experimental results indicates the importance of the independent rotations provided by Timoshenko beams over the simple beam theory. The delamination buckling of the beams was captured based on the static stability analysis in the first step. Further results show that the problem is more complex than it was thought before, e.g., some nonlinearity, time-dependent stiffness as well as parametric excitation aspects were discovered during the present analysis.

  2. Simulation of Thermographic Responses of Delaminations in Composites with Quadrupole Method

    Science.gov (United States)

    Winfree, William P.; Zalameda, Joseph N.; Howell, Patricia A.; Cramer, K. Elliott

    2016-01-01

    The application of the quadrupole method for simulating thermal responses of delaminations in carbon fiber reinforced epoxy composites materials is presented. The method solves for the flux at the interface containing the delamination. From the interface flux, the temperature at the surface is calculated. While the results presented are for single sided measurements, with ash heating, expansion of the technique to arbitrary temporal flux heating or through transmission measurements is simple. The quadrupole method is shown to have two distinct advantages relative to finite element or finite difference techniques. First, it is straight forward to incorporate arbitrary shaped delaminations into the simulation. Second, the quadrupole method enables calculation of the thermal response at only the times of interest. This, combined with a significant reduction in the number of degrees of freedom for the same simulation quality, results in a reduction of the computation time by at least an order of magnitude. Therefore, it is a more viable technique for model based inversion of thermographic data. Results for simulations of delaminations in composites are presented and compared to measurements and finite element method results.

  3. Delamination-Debond Behaviour of Composite T- Joints in Wind Turbine Blades

    Science.gov (United States)

    Gulasik, H.; Coker, D.

    2014-06-01

    Wind turbine industry utilizes composite materials in turbine blade structural designs because of their high strength/stiffness to weight ratio. T-joint is one of the design configurations of composite wind turbine blades. T-joints consist of a skin panel and a stiffener co-bonded or co-cured together with a filler material between them. T-joints are prone to delaminations between skin/stiffener plies and debonds between skin-stiffener-filler interfaces. In this study, delamination/debond behavior of a co-bonded composite T-joint is investigated under 0° pull load condition by 2D finite element method. Using Abaqus® commercial FE software, zero-thickness cohesive elements are used to simulate delamination/debond in ply interfaces and bonding lines. Pulling load at 0° is applied and load-displacement behavior and failure scenario are observed. The failure sequence consists of debonding of filler/stringer interface during one load drop followed by a second drop in which the 2nd filler/stringer debonds, filler/skin debonding and skin delamination leading to total loss of load carrying capacity. This type of failure initiation has been observed widely in the literature. When the debond strength is increased 30%, failure pattern is found to change in addition to increasing the load capacity by 200% before total loss of loading carrying capacity occurs. Failure initiation and propagation behavior, initial and max failure loads and stress fields are affected by the property change. In all cases mixed-mode crack tip loading is observed in the failure initiation and propagation stages. In this paper, the detailed delamination/debonding history in T-joints is predicted with cohesive elements for the first time.

  4. Effect of Material Property of Interply Film on the Delamination in Laminated Composites 8

    Institute of Scientific and Technical Information of China (English)

    WeiFENG; QiaoHUANG

    1999-01-01

    The delamination is one of the main failure modes in laminated composites.In order to suppress and /or delay it,considerable research has been devoted to the reduction of the interlaminar stresses at the interfaces between two different plies.This paper studies the effect of isotropic layers placed at ply interface on the interlaminar behaviour of the angle-ply laminated composites.The results of the experiment and numerical analysis show that the material properties of interply film have strong influence on the interlaminar behaviour of laminated composites.In order to suppress delamination,the material of interply film has to been selected carefully due to the fact that different matrials have different results .SOme materials may increase the stress values at the interfaces.Some materials may reduce the stress concertration.

  5. The Use of Sprint Interface Element Delamination Simulation of Sandwich Composite Beam

    Science.gov (United States)

    Xu, Geng; Yan, Renjun

    2016-12-01

    Sandwich composite beams have been more and more used in various industries because of their excellent mechanical properties. However, the mismatched performance between face sheet and foam core always lead to such as cracks and damages in the core or face/core interface during the processes of manufacturing or service. Delamination damage at the adhesive interface is the most dangerous and could be one main source that the mechanical capability of the structure is serous degenerated. In this paper, a simple and natural model to evaluate the stiffness of the spring interface elements, which is based on the physics and the geometry of the adhesive layers, is proposed. In order to validate the model, cantilever beam bending test were conducted for marine sandwich composite I-beam. A good comparison has been found between predictions and experimental results, and results indicate that the spring interface element can provide an efficient model for the delamination simulation of sandwich composite structures.

  6. Hierarchical system for autonomous sensing-healing of delamination in large-scale composite structures

    Science.gov (United States)

    Minakuchi, Shu; Sun, Denghao; Takeda, Nobuo

    2014-10-01

    This study combines our hierarchical fiber-optic-based delamination detection system with a microvascular self-healing material to develop the first autonomous sensing-healing system applicable to large-scale composite structures. In this combined system, embedded vascular modules are connected through check valves to a surface-mounted supply tube of a pressurized healing agent while fiber-optic-based sensors monitor the internal pressure of these vascular modules. When delamination occurs, the healing agent flows into the vascular modules breached by the delamination and infiltrates the damage for healing. At the same time, the pressure sensors identify the damaged modules by detecting internal pressure changes. This paper begins by describing the basic concept of the combined system and by discussing the advantages that arise from its hierarchical nature. The feasibility of the system is then confirmed through delamination infiltration tests. Finally, the hierarchical system is validated in a plate specimen by focusing on the detection and infiltration of the damage. Its self-diagnostic function is also demonstrated.

  7. Assessment of Composite Delamination Self-Healing Via Micro-Encapsulation

    Science.gov (United States)

    O'Brien, T. Kevin; White, Scott R.

    2008-01-01

    Composite skin/stringer flange debond specimens manufactured from composite prepreg containing interleaf layers with a polymer based healing agent encapsulated in thin walled spheres were tested. As a crack develops and grows in the base polymer, the spheres fracture releasing the healing agent. The agent reacts with catalyst and polymerizes healing the crack. In addition, through-thickness reinforcement, in the form of pultruded carbon z-pins were included near the flange tips to improve the resistance to debonding. Specimens were manufactured with 14 plies in the skin and 10 plies in the stiffener flange. Three-point bend tests were performed to measure the skin/stiffener debonding strength and the recovered strength after healing. The first three tests performed indicated no healing following unloading and reloading. Micrographs showed that delaminations could migrate to the top of the interleaf layer due to the asymmetric loading, and hence, bypass most of the embedded capsules. For two subsequent tests, specimens were clamped in reverse bending before reloading. In one case, healing was observed as evidenced by healing agent that leaked to the specimen edge forming a visible "scar". The residual strength measured upon reloading was 96% of the original strength indicating healing had occurred. Hence, self-healing is possible in fiber reinforced composite material under controlled conditions, i.e., given enough time and contact with pressure on the crack surfaces. The micro-encapsulation technique may prove more robust when capsule sizes can be produced that are small enough to be embedded in the matrix resin without the need for using an interleaf layer. However, in either configuration, the amount of healing that can occur may be limited to the volume of healing agent available relative to the crack volume that must be filled.

  8. Wave Propagation Analysis in Composite Laminates Containing a Delamination Using a Three-Dimensional Spectral Element Method

    Directory of Open Access Journals (Sweden)

    Fucai Li

    2012-01-01

    Full Text Available A three-dimensional spectral element method (SEM was developed for analysis of Lamb wave propagation in composite laminates containing a delamination. SEM is more efficient in simulating wave propagation in structures than conventional finite element method (FEM because of its unique diagonal form of the mass matrix. Three types of composite laminates, namely, unidirectional-ply laminates, cross-ply laminates, and angle-ply laminates are modeled using three-dimensional spectral finite elements. Wave propagation characteristics in intact composite laminates are investigated, and the effectiveness of the method is validated by comparison of the simulation results with analytical solutions based on transfer matrix method. Different Lamb wave mode interactions with delamination are evaluated, and it is demonstrated that symmetric Lamb wave mode may be insensitive to delamination at certain interfaces of laminates while the antisymmetric mode is more suited for identification of delamination in composite structures.

  9. Extended layerwise method for laminated composite plates with multiple delaminations and transverse cracks

    Science.gov (United States)

    Li, D. H.; Zhang, X.; Sze, K. Y.; Liu, Y.

    2016-10-01

    In this paper, the extended layerwise method (XLWM), which was developed for laminated composite beams with multiple delaminations and transverse cracks (Li et al. in Int J Numer Methods Eng 101:407-434, 2015), is extended to laminated composite plates. The strong and weak discontinuous functions along the thickness direction are adopted to simulate multiple delaminations and interlaminar interfaces, respectively, whilst transverse cracks are modeled by the extended finite element method (XFEM). The interaction integral method and maximum circumferential tensile criterion are used to calculate the stress intensity factor (SIF) and crack growth angle, respectively. The XLWM for laminated composite plates can accurately predicts the displacement and stress fields near the crack tips and delamination fronts. The thickness distribution of SIF and thus the crack growth angles in different layers can be obtained. These information cannot be predicted by using other existing shell elements enriched by XFEM. Several numerical examples are studied to demonstrate the capabilities of the XLWM in static response analyses, SIF calculations and crack growth predictions.

  10. Comprehensively simulating the mixed-mode progressive delamination in composite laminates

    Science.gov (United States)

    Gao, Zhenyuan

    Delamination, or interlaminar debonding, is a commonly observed failure mechanism in composite laminates. It is of great significance to comprehensively simulate the mixed-mode progressive delamination in composite structures because by doing this, people can save a lot of effort in evaluating the safe load which a composite structure can endure. The objective of this thesis is to develop a numerical approach to simulating double-cantilever beam (DCB) and mixed-mode bending (MMB) tests and also of specifying/validating various cohesive models. A finite element framework, which consists of properly selecting time integration scheme (explicit dynamic), viscosity, load rate and mass scaling, is developed to yield converged and accurate results. Two illustrative cohesive laws (linear and power-law) are programmed with a user- defined material subroutine for ABAQUS/Explicit, VUMAT, and implemented into the finite element framework. Parameters defined in cohesive laws are studied to evaluate their effects on the predicted load-displacement curves. The finite element model, together with the predetermined model parameters, is found to be capable of producing converged and accurate results. The finite element framework, embedded with the illustrative cohesive laws, is found to be capable of handling various interfacial models. The present approach is concluded to be useful in simulating delamination with more sophisticated material models. Together with the method for determining model parameters, it can be used by computer codes other than ABAQUS.

  11. Characterizing delamination of fibre composites by mixed mode cohesive laws

    DEFF Research Database (Denmark)

    Sørensen, Bent F.; Jacobsen, Torben K.

    2009-01-01

    A novel method is used for the determination of mixed mode cohesive laws and bridging laws for the characterisation of crack bridging in composites. The approach is based on an application of the J integral. The obtained cohesive laws were found to possess high peak stress values. Mixed mode...

  12. Transient Dynamic Response of Delaminated Composite Rotating Shallow Shells Subjected to Impact

    Directory of Open Access Journals (Sweden)

    Amit Karmakar

    2006-01-01

    Full Text Available In this paper a transient dynamic finite element analysis is presented to study the response of delaminated composite pretwisted rotating shallow shells subjected to low velocity normal impact. Lagrange's equation of motion is used to derive the dynamic equilibrium equation and moderate rotational speeds are considered wherein the Coriolis effect is negligible. An eight noded isoparametric plate bending element is employed in the finite element formulation incorporating rotary inertia and effects of transverse shear deformation based on Mindlin's theory. To satisfy the compatibility of deformation and equilibrium of resultant forces and moments at the delamination crack front a multipoint constraint algorithm is incorporated which leads to unsymmetric stiffness matrices. The modified Hertzian contact law which accounts for permanent indentation is utilized to compute the contact force, and the time dependent equations are solved by Newmark's time integration algorithm. Parametric studies are performed in respect of location of delamination, angle of twist and rotational speed for centrally impacted graphite-epoxy composite cylindrical shells.

  13. Segmenting delaminations in carbon fiber reinforced polymer composite CT using convolutional neural networks

    Science.gov (United States)

    Sammons, Daniel; Winfree, William P.; Burke, Eric; Ji, Shuiwang

    2016-02-01

    Nondestructive evaluation (NDE) utilizes a variety of techniques to inspect various materials for defects without causing changes to the material. X-ray computed tomography (CT) produces large volumes of three dimensional image data. Using the task of identifying delaminations in carbon fiber reinforced polymer (CFRP) composite CT, this work shows that it is possible to automate the analysis of these large volumes of CT data using a machine learning model known as a convolutional neural network (CNN). Further, tests on simulated data sets show that with a robust set of experimental data, it may be possible to go beyond just identification and instead accurately characterize the size and shape of the delaminations with CNNs.

  14. A subregional model for delamination prediction of rubber composite under fatigue loading

    Institute of Scientific and Technical Information of China (English)

    TIAN Zhen-hui; TAN Hui-feng

    2005-01-01

    Results from fatigue experiments of cross-laminated steel cord-rubber composites (SCRC) indicate that fatigue damage life can be categorized into three regimes. In terms of fatigue modes, a subregional fatigue model is developed to describe the damages evolution of SCRC under fatigue loads. Firstly, finite element analysis is introduced to determine interply stress distribution of the specimen. Then, based on the experimental fatigue data, subregional models are introduced to simulate relations between maximum strain, effective stiffness,delamination shear stress and fatigue cycles. Relations between crack density, delamination length growth rate,macro crack density and cycles are modeled by two semi-empirical models. A reasonable prediction result was achieved by the current model, where model parameters can be determined by basic outputs of fatigue testing.

  15. Assessment of Composite Delamination Self-Healing Under Cyclic Loading

    Science.gov (United States)

    O'Brien, T. Kevin

    2009-01-01

    Recently, the promise of self-healing materials for enhanced autonomous durability has been introduced using a micro-encapsulation technique where a polymer based healing agent is encapsulated in thin walled spheres and embedded into a base polymer along with a catalyst phase. For this study, composite skin-stiffener flange debonding specimens were manufactured from composite prepreg containing interleaf layers with a polymer based healing agent encapsulated in thin-walled spheres. Constant amplitude fatigue tests in three-point bending showed the effect of self-healing on the fatigue response of the skin-stiffener flange coupons. After the cycling that created debonding, fatigue tests were held at the mean load for 24 hours. For roughly half the specimens tested, when the cyclic loading was resumed a decrease in compliance (increase in stiffness) was observed, indicating that some healing had occurred. However, with continued cycling, the specimen compliance eventually increased to the original level before the hold, indicating that the damage had returned to its original state. As was noted in a prevoius study conducted with specimens tested under monotonically increasing loads to failure, healing achieved via the micro-encapsulation technique may be limited to the volume of healing agent available relative to the crack volume.

  16. Modeling Delamination in Postbuckled Composite Structures Under Static and Fatigue Loads

    Science.gov (United States)

    Bisagni, Chiara; Brambilla, Pietro; Bavila, Carlos G.

    2013-01-01

    The ability of the Abaqus progressive Virtual Crack Closure Technique (VCCT) to model delamination in composite structures was investigated for static, postbuckling, and fatigue loads. Preliminary evaluations were performed using simple Double Cantilever Beam (DCB) and Mixed-Mode Bending (MMB) specimens. The nodal release sequences that describe the propagation of the delamination front were investigated. The effect of using a sudden or a gradual nodal release was evaluated by considering meshes aligned with the crack front as well as misaligned meshes. Fatigue simulations were then performed using the Direct Cyclic Fatigue (DCF) algorithm. It was found that in specimens such as the DCB, which are characterized by a nearly linear response and a pure fracture mode, the algorithm correctly predicts the Paris Law rate of propagation. However, the Abaqus DCF algorithm does not consider different fatigue propagation laws in different fracture modes. Finally, skin/stiffener debonding was studied in an aircraft fuselage subcomponent in which debonding occurs deep into post-buckling deformation. VCCT was shown to be a robust tool for estimating the onset propagation. However, difficulties were found with the ability of the current implementation of the Abaqus progressive VCCT to predict delamination propagation within structures subjected to postbuckling deformations or fatigue loads.

  17. Debonding/Delamination of Composites (Le Decollement et le Delaminage des Materiaux Composites)

    Science.gov (United States)

    1992-12-01

    bouthS sides of the delamination. Fig 8a. Ithese cratcks coincide with the delamination length Linder conipressise loadingthe 1.1D-sublaminate buckles like...Scientific 115] R.O. Duda, PE. Hart , "Pattern classification and scene Research (NFWO) for its funding Considerable help was also analysis", John...unidirectional laminates were performed with the technology of differential 2 MATERIALS AND PREPARATIONS scanning calorimetry A Du Pont DSC system, model 910, was

  18. Internal-Notched Flexure Test for Measurement of Mode II Delamination Resistance of Fibre-Reinforced Polymers

    Directory of Open Access Journals (Sweden)

    Chengye Fan

    2013-01-01

    Full Text Available This paper introduces a new test, method, named internal-notched flexure (INF test, that is designed to measure the critical energy release rate of fibre-reinforced polymers for delamination growth in shear mode (mode II. The INF test generates stable delamination growth, with a monotonic increase of load and displacement in a nearly linear fashion. Values of the mode II delamination toughness were deduced using experimental compliance fitting method. Good repeatability of the results was obtained. Compared with the end-notched flexure (ENF test using the same material, the INF test yielded higher delamination resistance, possibly due to the bridging fibres found between fracture surfaces of the INF test specimens.

  19. COMPOSITIONAL AND THERMAL DIFFERENCES BETWEEN LITHOSPHERIC AND ASTHENOSPHERIC MANTLE AND THEIR INFLUENCE ON CONTINENTAL DELAMINATION

    Directory of Open Access Journals (Sweden)

    A. I. Kiselev

    2015-09-01

    Full Text Available The lower part of lithosphere in collisional orogens may delaminate due to density inversion between the asthenosphere and the cold thickened lithospheric mantle. Generally, standard delamination models have neglected density changes within the crust and the lithospheric mantle, which occur due to phase transitions and compositional variations upon changes of P-T parameters. Our attention is focused on effects of phase and density changes that may be very important and even dominant when compared with the effect of a simple change of the thermal mantle structure. The paper presents the results of numerical modeling for eclogitization of basalts of the lower crust as well as phase composition changes and density of underlying peridotite resulted from tectonic thickening of the lithosphere and its foundering into the asthenosphere. As the thickness of the lower crust increases, the mafic granulite (basalt passes into eclogite, and density inversion occurs at the accepted crust-mantle boundary (P=20 kbar because the newly formed eclogite is heavier than the underlying peridotite by 6 % (abyssal peridotite, according to [Boyd, 1989]. The density difference is a potential energy for delamination of the eclogitic portion of the crust. According to the model, P=70 kbar and T=1300 °C correspond to conditions at the lower boundary of the lithosphere. Assuming the temperature adiabatic distribution within the asthenosphere, its value at the given parameters ranges from 1350 °C to 1400 °C. Density inversion at dry conditions occurs with the identical lithospheric and asthenospheric compositions at the expense of the temperature difference at 100 °C with the density difference of only 0.0022 %. Differences of two other asthenospheric compositions (primitive mantle, and lherzolite KH as compared to the lithosphere (abyssal peridotite are not compensated for by a higher temperature. The asthenospheric density is higher than that of the lithospheric base

  20. The nanoindentation applied to predict the interface delamination for the C/amorphous Si composite film

    Science.gov (United States)

    Han, Chang-Fu; Huang, Chao-Yu; Wu, Bo-Hsiung; Lin, Jen-Fin

    2009-10-01

    In the present study, the indentation depth corresponding to the pop-in arising in the loading process is found to be quite close to the C/amorphous Si composite film thickness, regardless of the C-film thickness. This load-depth behavior gives a clue that the occurrence of pop-in is perhaps related to the buckling of the composite film, which had already delaminated from the silicon substrate. This indentation depth of buckling predicted by the present model is quite close to the pop-in depth obtained from experimental results, regardless of the change in the C-film thickness. This characteristic reveals that the present model is developed successfully to predict the pop-in depth of a specimen, and the pop-in is indeed created due to the buckling of the composite film under a compression stress.

  1. Stability Loss and Buckling Delamination Three-Dimensional Linearized Approach for Elastic and Viscoelastic Composites

    CERN Document Server

    Akbarov, Surkay

    2013-01-01

    This book investigates stability loss and buckling delamination problems of the viscoelastic composite materials and structural members made from these materials within the framework of the Three-Dimensional Linearized Theory of Stability (TDLTS). The investigation of stability loss problems is based on the study of an evolution of the initial infinitesimal imperfection in the structure of the material or of the structural members with time (for viscoelastic composites) or with external compressing forces (for elastic composites). This study is made within the scope of the Three-Dimensional Geometrically Non-Linear Theory of the Deformable Solid Body Mechanics. The solution to the corresponding boundary-value problems is presented in the series form in a small parameter which characterizes the degree of the initial imperfection. The boundary form perturbation technique is employed and nonlinear problems for the domains bounded by noncanonical surfaces are reduced to the same nonlinear problem for the correspo...

  2. Probabilistic Delamination Diagnosis of Composite Materials Using a Novel Bayesian Imaging Method

    Data.gov (United States)

    National Aeronautics and Space Administration — In this paper, a probabilistic delamination location and size detection framework is proposed. The delamination probability image using Lamb wave-based damage...

  3. Rapid guided wave delamination detection and quantification in composites using global-local sensing

    Science.gov (United States)

    Tian, Zhenhua; Yu, Lingyu; Leckey, Cara

    2016-08-01

    This paper presents a rapid guided ultrasonic wave inspection approach through global inspection by phased array beamforming and local damage evaluation via wavenumber analysis. The global-local approach uses a hybrid system consisting of a PZT wafer and a non-contact laser vibrometer. The overall inspection is performed in two steps. First, a phased array configured by a small number of measurements performs beamforming and beamsteering over the entire plate in order to detect and locate the presence of the damage. A local area is identified as target damage area for the second step. Then a high density wavefield measurement is taken over the target damage area and a spatial wavenumber imaging is performed to quantitatively evaluate the damage. The two-step inspection has been applied to locate and quantify impact-induced delamination damage in a carbon fiber reinforced polymer composite plate. The detected delamination location, size and shape agree well with those of an ultrasonic C-scan. For the test case studied in this work the global-local approach reduced the total composite inspection (damage detection and characterization) time by ∼97% compared to using a full scan approach.

  4. Free Edge Mixed Mode Delamination Analysis of Laminated Composites with Wrap-Around Configuration: A Finite Element Study

    Science.gov (United States)

    Choudhury, Pannalal; Das, Subhankar; Halder, Sudipta; Pandey, Krishna Murari

    2016-10-01

    Finite element analyses of laminated composites were done in the present study with respect to suppression of free edge delamination by an innovative technique. Wrap-around configuration was considered to determine its effectiveness over the wrapper-less laminated configuration on laminated composites. Nodal stresses were generated ahead of the crack tip through finite element analysis. This was used for determining interlaminar normal stress and inter laminar shear stress distributions at the critical interface. Later virtual crack closure technique was used to estimate the strain energy release rate components for several sizes of virtual crack extensions through a single finite element analysis. Computational analysis predicts Mode-I delamination as dominant mode of failure. This mode of delamination was significantly suppressed with wrap-around configuration on laminated composites.

  5. A unified approach to modeling delamination and matrix cracking in smart composite structures

    Science.gov (United States)

    Thornburgh, Robert Preston

    The development of smart structures technology has coincided with the increased use of composite materials in structural design. Composite laminates have forms of damage that are not found in other materials, specifically delamination and transverse matrix cracking. An in-depth understanding of the effects of damage on smart composite structures is necessary for predicting not only the life of the structure, but also for modeling any method to be used for damage detection. The objective of this research was to develop a comprehensive model for accurately and efficiently modeling smart composite structures including the effects of composite damage. First, a new, efficient method for modeling smart structures with piezoelectric devices was developed. The coupled model simultaneously solves for the mechanical and electrical response of the system using mechanical displacements and electrical displacements. The developed theory utilizes a refined higher order displacement field that accurately captures the transverse shear deformation in moderately thick laminates. The model was then extended to include internal damage in the form of delamination and matrix cracking. When delamination is present, the sublaminates are modeled as individual plates and continuity is enforced at the interfaces. Matrix cracking was modeled as a reduction in laminate stiffness using parameters determined using finite element analysis of a representative crack. Finally, the simultaneous optimization of both mechanical and electrical parameters in an adaptive structural system was studied. This study demonstrates how multidisciplinary optimization techniques, such as the Kreisselmeier-Steinhauser function, can be utilized to optimize both structural and electrical aspects of an adaptive structural system. Optimization of piezoelectric actuator placement and electrical circuitry was performed on passive electrical damping systems. Results show that the developed model is capable of accurately

  6. The Effect of Strike Face Geometry on the Dynamic Delamination of Composite Back Plates

    Science.gov (United States)

    2015-01-01

    Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202-4302. Respondents should be aware that...specimen allowed for capture of dynamic delamination images with high-speed photography . The projected delamination area was quantified using commercially...14 Fig. B-1 Delaminations outlined using tools in Image Pro Plus ..................................................22 Fig. B-2 Yellow

  7. An automated dynamic fracture procedure and a continuum damage mechanics based model for finite element simulations of delamination failure in laminated composites

    Science.gov (United States)

    Aminjikarai Vedagiri, Srinivasa Babu

    explicitly in the model induces spurious high-frequency oscillations in the finite element results after crack initiation, a "gradual nodal release" procedure is implemented as part of the model to overcome this problem. Also, an in-built contact algorithm of DYNA3D is modified to adapt it to the remeshing strategy to maintain proper contact conditions at newly added elements. Finally, the model is suitably modified for simulating delamination failure in laminated composites and used to predict delamination resistance characteristics which are important considerations for effective use of composite structures. Continuum damage mechanics is a popular approach for modeling the in-plane failure modes in composites. However, its applicability to modeling delamination has not been sufficiently analyzed yet. Hence, as the second part of this dissertation work, a new material model is developed for unidirectional polymer matrix composites in which this approach is used to predict delamination failure and used to perform a qualitative study of the damage mechanics approach to modeling delamination. The new material model is developed using micro-mechanics and accounts for the strain-rate dependent behavior of polymer matrix composites. It is implemented for three different element formulations with different transverse shear strain assumptions and the effect of these assumptions on the delamination prediction using this approach is analyzed.

  8. Interlaminar fracture toughness of composites. II - Refinement of the edge delamination test and application to thermoplastics

    Science.gov (United States)

    Johnston, N. J.; Obrien, T. K.; Morris, D. H.; Simonds, R. A.

    1983-01-01

    The mixed mode interlaminar fracture toughness, G(c), is obtained for the two thermoplastic matrices UDEL P1700 polysulfone and ULTEM polyetherimide by means of edge delamination tensile (EDT) tests on unnotched, eleven-ply graphite fiber reinforced composite specimens. A novel method is used to obtain the stiffness parameter employed in the closed form equation for the calculation of G(c), decreasing the number of stiffness measurements required and simplifying the calculations. The G(Ic) values from double cantilever beam (DCB) measurements on composites of the two thermoplastics were similar to each other, but slightly higher than the G(c) data obtained by EDT. Interfacial resin/fiber failures predominated in both the EDT and DCB tests.

  9. Irradiation and annealing effects on delamination toughness in carbon/epoxy composite

    Energy Technology Data Exchange (ETDEWEB)

    Sekulic, D.R. [Institute of Nuclear Sciences, Vinca, POB 522, 11000 Belgrade, Serbia (Serbia )], E-mail: pesikan@vin.bg.ac.yu; Gordic, M.V. [General High School Milutin Milankovic, 11000 Belgrade (Serbia); Djordjevic, I.M. [Institute of Nuclear Sciences, Vinca, POB 522, 11000 Belgrade (Serbia); Petrovic, Z.S. [Kansas Polymer Research Center, Pittsburgh State University (United States); Stevanovic, M.M. [Institute of Nuclear Sciences, Vinca, POB 522, 11000 Belgrade (Serbia)

    2009-01-01

    Gamma irradiation to various doses (4.8-27.2 MGy) was performed on unidirectional carbon fiber/epoxy resin composite plates. Unidirectional composite coupons irradiated to various doses were annealed at 180 and 250 deg. C, in vacuum. The strain energy release rate G{sub IC}, as a measure of delamination fracture toughness, was determined by Mode I fracture testing on double cantilever beam coupons. The glass transition temperature (T{sub g}) of the tested coupons matrices was determined in DMA tests. The effects of irradiation and annealing on G{sub IC} values - the mean values of 10 propagation points (G{sub IC,mean}) and that of fracture initiation (G{sub IC,init}) - were established. These values were analyzed as a function of irradiation dose and annealing temperatures, having in mind glass transition temperature values changes, as well as the possible mechanisms and phenomena of irradiation and annealing.

  10. The effect of transverse shear on the postbuckling and growth characteristics of delaminations in composites

    Energy Technology Data Exchange (ETDEWEB)

    Ferrie, C.H.; Sheinman, I.; Kardomateas, G.A.

    1999-10-01

    A geometrically nonlinear formulation for the behavior of composite delaminated beams of arbitrary stacking sequence, and with the effects of transverse shear deformation included, is presented. The formulation is based on a first-order shear deformation kinematic model, which incorporates the bending-stretching coupling effect and also assumes an arbitrary initial imperfection. The nonlinear differential equations are solved by Newton's method using a finite-difference scheme. The growth of the delamination is also studied by applying the J-integral in order to derive a formula for the energy release rate, which includes transverse shear. Results are presented which illustrate the shear effect, especially with respect to the ratio of the in-plane extensional over shear modulus and with respect to the ratio of plate length over thickness. It is seen that transverse shear can affect largely the displacement profiles, rendering the structure more compliant, and can promote growth by increasing the energy release rate, but this latter effect is moderate and mainly noticeable only at the later stages in the postbuckling regime.

  11. Multi-site delamination detection and quantification in composites through guided wave based global-local sensing

    Science.gov (United States)

    Tian, Zhenhua; Leckey, Cara; Yu, Lingyu

    2017-02-01

    This paper presents a guided wave based global-local sensing method for rapid detection and quantification of multi-site delamination damage in large composite panels. The global-local approach uses a hybrid system consisting of a piezoelectric transducer (PZT) for generating guided waves and a non-contact scanning laser Doppler vibrometer (SLDV) for acquiring guided wave data. The global-local method is performed in two steps. First, a phased array configured of a small number of SLDV scan points (for example 10×10 points in a rectangular grid array) performs inspection over the entire plate to detect and locate damage. Local areas are identified as potential damage regions for the second step. Then high density wavefield measurements are taken over the identified areas and wavefield analysis is performed to quantitatively evaluate the damage. For the proof of concept in case with multi-site damage, the global-local approach is demonstrated on a carbon fiber reinforced polymer (CFRP) composite plate with two sites of impact-induced delamination damage. In the first step, the locations of two delamination sites are detected by the phased array method. In the second step, the delamination size and shape are evaluated using wavefield analysis. The detected delamination location, size and shape agree well with those of ultrasonic C-scan and the method led to a 93% reduction in inspection time compared to a full SLDV dense grid scan.

  12. Applicability of various wood species in glued laminated timber: Parameter study on delamination resistance and shear strength

    NARCIS (Netherlands)

    Jiang, Y.; Schaffrath, J.; Knorz, M.; Winter, S.; Van de Kuilen, J.W.G.

    2014-01-01

    In a current research project the gluability of four European timber species and their applicability in glued laminated timber is investigated. The influence of different processing parameters on the adhesive bonding is assessed with regard to shear strength and delamination resistance. Furthermore,

  13. Self-healing of low-velocity impact and mode-I delamination damage in polymer composites via microchannels

    Directory of Open Access Journals (Sweden)

    M. U. Saeed

    2016-04-01

    Full Text Available Microchannels embedded polymer composites were fabricated by resin infusion process using carbon fabric, epoxy resin and hollow glass tubes (HGTs. The effect of a range of low-velocity impact (LVI and mode-I delamination (M1D damage on the flexural strength of microchanneled carbon- epoxy composites was studied. A self-healing approach was also employed to recover their lost flexural strength due to these damages. Moreover, influence of LVI, M1D damage and healing on the failure behavior of microchanneled carbon- epoxy composites was also investigated. The results of flexural after impact (FAI and flexural after delamination (FAD showed that LVI has more deleterious effect on the flexural strength of carbon- epoxy composites than M1D damage. The loss in flexural strength increased linearly with increase in both impact (by higher impact energies and delamination damage (by longer delamination lengths. Scanning electron microscopic (SEM study revealed that self-healing agent (SHA, stored in HGTs placed within carbon- epoxy composites, effectively healed both LVI and M1D damage with excellent healing efficiencies.

  14. Quantitative 3D X-ray imaging of densification, delamination and fracture in a micro-composite under compression

    DEFF Research Database (Denmark)

    Bø Fløystad, Jostein; Skjønsfjell, Eirik Torbjørn Bakken; Guizar-Sicairos, Manuel

    2015-01-01

    Phase-contrast three-dimensional tomograms showing in unprecedented detail the mechanical response of a micro-composite subjected to a mechanical compression test are reported. The X-ray ptychography images reveal the deformation and fracture processes of a 10 μm diameter composite, consisting......-dimensional tomograms reveal with unprecedented detail the mechanical response, including delamination, densification and fracture, of a polymer-core/silver-shell micro-composite subjected in situ to a mechanical compression test....

  15. An high order Mixed Interpolation Tensorial Components (MITC) shell element approach for modeling the buckling behavior of delaminated composites

    DEFF Research Database (Denmark)

    Gaiotti, Marco; Rizzo, Cesare M.; Branner, Kim

    2014-01-01

    of composite laminates of wind turbine blades, results were found valuable for the marine industry as well, because similar laminates are used for the hull shell and stiffeners. Systematic calculations were carried out to assess the effects of an embedded delamination on the buckling load, varying the size...... and through thickness position of the delamination. Different finite element modeling strategies were considered and validated against the experimental results. The one applying the 9 nodes MITC shell elements was found matching the experimental data despite failure modes were different for the two...

  16. Modeling the Effects of Beam Size and Flaw Morphology on Ultrasonic Pulse/Echo Sizing of Delaminations in Carbon Composites

    Science.gov (United States)

    Margetan, Frank J.; Leckey, Cara A.; Barnard, Dan

    2012-01-01

    The size and shape of a delamination in a multi-layered structure can be estimated in various ways from an ultrasonic pulse/echo image. For example the -6dB contours of measured response provide one simple estimate of the boundary. More sophisticated approaches can be imagined where one adjusts the proposed boundary to bring measured and predicted UT images into optimal agreement. Such approaches require suitable models of the inspection process. In this paper we explore issues pertaining to model-based size estimation for delaminations in carbon fiber reinforced laminates. In particular we consider the influence on sizing when the delamination is non-planar or partially transmitting in certain regions. Two models for predicting broadband sonic time-domain responses are considered: (1) a fast "simple" model using paraxial beam expansions and Kirchhoff and phase-screen approximations; and (2) the more exact (but computationally intensive) 3D elastodynamic finite integration technique (EFIT). Model-to-model and model-to experiment comparisons are made for delaminations in uniaxial composite plates, and the simple model is then used to critique the -6dB rule for delamination sizing.

  17. Ultrasonic characterization of delamination in aeronautical composites using noncontact laser generation and detection.

    Science.gov (United States)

    Sun, Guangkai; Zhou, Zhenggan; Chen, Xiucheng; Wang, Jie

    2013-09-10

    The characterization of delamination in composite plates with ultrasonic waves generated and detected by lasers is presented. Composite materials have become one of the most important structural materials in the aviation industry because of their excellent mechanical properties, such as high specific stiffness and antifatigue. This paper reports a new application of the laser ultrasonic technique to perform nondestructive detection of carbon-fiber-reinforced plastic (CFRP) and continuous-fiber-reinforced ceramic matrix composites (CFCCs) containing artificial internal defects, based on propagation characteristic of ultrasonic waves generated by pulse laser with a wavelength of 1064 nm and pulse duration of 10 ns. A laser interferometer based on two-wave mixing is used to measure ultrasonic wave signals. The main advantage of this technique over conventional ultrasonic testing techniques is the ability to carry out detection without using coupling agents. The research results prove that the laser ultrasonic technique is effective for the detection of internal defects in both CFRP and CFCC composite components, which should promote and expand the application of the technique in the aviation industry.

  18. Air-coupled guided wave detection and wavenumber filtering to full-field representation of delamination in composite plates

    Science.gov (United States)

    Testoni, N.; De Marchi, L.; Marzani, A.

    2014-03-01

    Delamination faults in composite plates are considered dangerous as they can cause catastrophic failure before being visually assessed. Effects of delaminations are particularly relevant in guided waves scattering, local resonances and mode conversion. Detecting and analyzing these phenomena is relevant for plate characterization. In this work, leaky guided waves are used to detect delamination in composite plates. To such purpose, a hybrid ultrasonic set-up and a dedicated signal processing are proposed. An air-probe with a proper lift-off is used to detect the leakage in terms of air pressure wave over the plate surface. A piezoelectric transducer is used to generate acoustic guided waves in the composite plate. Multiple acquisitions are averaged to increase the SNR for each position of the air-probe. Curvelet Transform (CT) domain processing of the projection coefficients of the acquired elastic wave is exploited to decompose waves that are overlapped both in the time/space and in the frequency/wavenumber domain. In fact, CT is a special member of the family of multiscale and multidimensional transforms whose spatial and temporal localization is very well suited for processing signals which are sparse in the above mentioned domains. In this work this sparsity is exploited to emphasize the information of leaky guided waves scattered by the delamination by removing from the data the information related to the incident wave field. As an application, the presence of a delamination generated by a 21 Joule impact performed on a 4.9 mm thickness composite laminate was detected contactless by exploiting guided wave leakage.

  19. Finite Element Analysis of Layered Fiber Composite Structures Accounting for the Material's Microstructure and Delamination

    Science.gov (United States)

    Stier, Bertram; Simon, Jaan-Willem; Reese, Stefanie

    2015-04-01

    The present paper focuses on composite structures which consist of several layers of carbon fiber reinforced plastics (CFRP). For such layered composite structures, delamination constitutes one of the major failure modes. Predicting its initiation is essential for the design of these composites. Evaluating stress-strength relation based onset criteria requires an accurate representation of the through-the-thickness stress distribution, which can be particularly delicate in the case of shell-like structures. Thus, in this paper, a solid-shell finite element formulation is utilized which allows to incorporate a fully three-dimensional material model while still being suitable for applications involving thin structures. Moreover, locking phenomena are cured by using both the EAS and the ANS concept, and numerical efficiency is ensured through reduced integration. The proposed anisotropic material model accounts for the material's micro-structure by using the concept of structural tensors. It is validated by comparison to experimental data as well as by application to numerical examples.

  20. Application of layered finite elements in the numerical analysis of laminated composite and sandwich structures with delaminations

    Directory of Open Access Journals (Sweden)

    Vuksanović Đorđe

    2015-01-01

    Full Text Available Laminar composites are modern engineering materials widely used in the mechanical and civil engineering. In the paper, some recent advances in a numerical analysis of laminated composite and sandwich plates and shells of different shapes, with existing zones of partial delamination, are presented. The layered finite elements, based on the extended version of the Generalized Laminated Plate Theory of Reddy, are applied for the numerical solution of several structural problems. After the verification of the proposed model for intact structures using the existing data from the literature, the effects of the size and the position of embedded delamination zones on the structural response of laminated structures are investigated numerically by means of a variety of numerical applications.

  1. Experimental approach for mixed-mode fatigue delamination crack growth with large-scale bridging in polymer composites

    DEFF Research Database (Denmark)

    Holmes, John W.; Liu, Liu; Sørensen, Bent F.

    2014-01-01

    of delaminations in a typical fibre-reinforced polymer composite was investigated under a constant cyclic loading amplitude. Pure mode I, mode II and mixed-mode crack growth conditions were examined. The results, analysed using a J-integral approach, show that the double cantilever beam loaded with uneven bending......An experimental apparatus utilizing double cantilever beam specimens loaded with uneven bending moments was developed to study the mixed-mode fatigue crack growth in composites. The approach is suitable when large-scale bridging of cracks is present. To illustrate the testing method, cyclic growth...... crack growth rate observed. In addition to details concerning the equipment, a general discussion of the development of cyclic bridging laws for delamination growth in the presence of large-scale bridging is provided....

  2. DELAMINATION PREDICTION IN DRILLING OF CFRP COMPOSITES USING ARTIFICIAL NEURAL NETWORK

    Directory of Open Access Journals (Sweden)

    K. PALANIKUMAR

    2011-04-01

    Full Text Available Carbon fibre reinforced plastic (CFRP materials play a major role in the applications of aeronautic, aerospace, sporting and transportation industries. Machining is indispensible and hence drilling of CFRP materials is considered in this present study with respect to spindle speed in rpm, drill size in mm and feed in mm/min. Delamination is one of the major defects to be dealt with. The experiments are carried out using computer numerical control machine and the results are applied to an artificial neural network (ANN for the prediction of delamination factor at the exit plane of the CFRP material. It is found that ANN model predicts the delamination for any given set of machining parameters with a maximum error of 0.81% and a minimum error of 0.03%. Thus an ANN model is highly suitable for the prediction of delamination in CFRP materials.

  3. Comparison of Nondestructive Testing Methods on Detection of Delaminations in Composites

    Directory of Open Access Journals (Sweden)

    Liang Cheng

    2012-01-01

    Full Text Available Delamination is one of the most common defects in carbon fibre reinforced plastic (CFRP components, such as those used in aircraft and wind turbine blades. To detect delaminations, different NDT methods such as ultrasonic (UT, eddy current (EC scanning, flash thermography, and recent developed pulsed-eddy-current-(PEC- simulated thermography are conducted for comparison and evaluation of the new developed PEC thermography system at Nanjing University of Aeronautics and Astronautics (NUAA, China through UK-China collaboration. A PEC-stimulated thermography system is built at NUAA, extended from previous joint work between Newcastle and Bath Universities. Using these NDT systems, man-made, dedicated delaminations with varied diameters and depths are investigated and studied. Through this comparison, PEC-stumilated and flash thermography show relatively good indications of the shape of delaminations. The joint studies also show that PEC-stimulated thermography has unique advantage for fibre orientation evaluation.

  4. Mixed-Mode Decohesion Finite Elements for the Simulation of Delamination in Composite Materials

    Science.gov (United States)

    Camanho, Pedro P.; Davila, Carlos G.

    2002-01-01

    A new decohesion element with mixed-mode capability is proposed and demonstrated. The element is used at the interface between solid finite elements to model the initiation and non-self-similar growth of delaminations. A single relative displacement-based damage parameter is applied in a softening law to track the damage state of the interface and to prevent the restoration of the cohesive state during unloading. The softening law for mixed-mode delamination propagation can be applied to any mode interaction criterion such as the two-parameter power law or the three-parameter Benzeggagh-Kenane criterion. To demonstrate the accuracy of the predictions and the irreversibility capability of the constitutive law, steady-state delamination growth is simulated for quasistatic loading-unloading cycles of various single mode and mixed-mode delamination test specimens.

  5. Modeling of delamination in carbon/epoxy composite laminates under four point bending for damage detection and sensor placement optimization

    Science.gov (United States)

    Adu, Stephen Aboagye

    Laminated carbon fiber-reinforced polymer composites (CFRPs) possess very high specific strength and stiffness and this has accounted for their wide use in structural applications, most especially in the aerospace industry, where the trade-off between weight and strength is critical. Even though they possess much larger strength ratio as compared to metals like aluminum and lithium, damage in the metals mentioned is rather localized. However, CFRPs generate complex damage zones at stress concentration, with damage progression in the form of matrix cracking, delamination and fiber fracture or fiber/matrix de-bonding. This thesis is aimed at performing; stiffness degradation analysis on composite coupons, containing embedded delamination using the Four-Point Bend Test. The Lamb wave-based approach as a structural health monitoring (SHM) technique is used for damage detection in the composite coupons. Tests were carried-out on unidirectional composite coupons, obtained from panels manufactured with pre-existing defect in the form of embedded delamination in a laminate of stacking sequence [06/904/0 6]T. Composite coupons were obtained from panels, fabricated using vacuum assisted resin transfer molding (VARTM), a liquid composite molding (LCM) process. The discontinuity in the laminate structure due to the de-bonding of the middle plies caused by the insertion of a 0.3 mm thick wax, in-between the middle four (4) ninety degree (90°) plies, is detected using lamb waves generated by surface mounted piezoelectric (PZT) actuators. From the surface mounted piezoelectric sensors, response for both undamaged (coupon with no defect) and damaged (delaminated coupon) is obtained. A numerical study of the embedded crack propagation in the composite coupon under four-point and three-point bending was carried out using FEM. Model validation was then carried out comparing the numerical results with the experimental. Here, surface-to-surface contact property was used to model the

  6. Methods for the prediction of fatigue delamination growth in composites and adhesive bonds: A critical review

    NARCIS (Netherlands)

    Pascoe, J.A.; Alderliesten, R.C.; Benedictus, R.

    2013-01-01

    An overview is given of the development of methods for the prediction of fatigue driven delamination growth over the past 40 years. Four categories of methods are identified: stress/strain-based models, fracture mechanics based models, cohesive-zone models, and models using the extended finite eleme

  7. Self-healing Nanofiber-Reinforced Polymer Composites. 2. Delamination/Debonding and Adhesive and Cohesive Properties.

    Science.gov (United States)

    Lee, Min Wook; An, Seongpil; Jo, Hong Seok; Yoon, Sam S; Yarin, Alexander L

    2015-09-09

    The capacity for core-shell nanofiber mats containing healing agents (resin monomer and cure) in their cores to adhere to a substrate was studied using blister testing. After extended periodic bending, the adhesion energy was measured, and the effect of self-healing on the composite's delamination from the substrate was considered. In addition, the cohesion of two layers of the self-healing nanofibers was examined using blister testing and compared to that of ordinary nanofiber mats. The damage inflicted by prolonged periodic bending to the interface of the two nanofiber mats was demonstrated to have self-healed, and the cohesion energy was measured.

  8. Lamb wave sensing using fiber Bragg grating sensors for delamination detection in composite laminates

    Science.gov (United States)

    Takeda, N.; Okabe, Y.; Kuwahara, J.; Kojima, S.

    2005-05-01

    The authors are constructing a damage detection system using ultrasonic waves. In this system, a piezo-ceramic actuator generates Lamb waves in a CFRP laminate. After the waves propagate in the laminate, transmitted waves are received by a fiber Bragg grating (FBG) sensor attached on the laminate using a newly developed high-speed optical wavelength interrogation system. At first, the optimal gauge length of the FBG to detect ultrasonic waves was investigated through theoretical simulations and experiments. Then, the directional sensitivity of the FBG to ultrasonic waves was evaluated experimentally. On the basis of the above results, the 1mm FBG sensors were applied to the detection of Lamb waves propagated in carbon fiber reinforced plastic (CFRP) cross-ply laminates. The piezo-actuator was put on the laminate about 50mm away from the FBG sensor glued on the laminate, and three-cycle sine waves of 300kHz were excited repeatedly. The waveforms obtained by the FBG showed that S0 and A0 modes could be detected appropriately. Then, artificial delamination was made in the laminate by removing of a Teflon sheet embedded in the 0/90 interface after the manufacturing. When the Lamb waves passed through the delamination, the amplitude decreased and a new wave mode appeared. These phenomena could be well simulated using a finite element method. Furthermore, since the amplitude and the velocity of the new mode increased with an increase in the delamination length, this system has a potential to evaluate the interlaminar delamination length quantitatively.

  9. Evaluation of NaCl Effect on Vibration-Delaminated Metal-Polymer Composites by Improved Micro-Raman Methodology

    Directory of Open Access Journals (Sweden)

    E. Zumelzu

    2013-01-01

    Full Text Available Polyethylene terephthalate (PET is a polymer coating that protects the electrolytic chromium coated steel (ECCS against aggressive electrolytes like NaCl. It is widely accepted by manufacturers that NaCl has no effect on the PET coating, which is inert. However, we showed that there are some effects at the structural level, caused by vibrations, and facilitated by defects on the layers. The vibrations occurring during the transportation of food containers produce delaminations at given points of the metal-polymer interface, known as antinodes, which in turn may produce PET degradation affecting food quality. The former can be determined by electrochemical measurements, and the changes in composition or structural order can be characterized by Raman. The present work applied this latter technique in experimental samples of PET-coated ECCS sheets by performing perpendicular and parallel analyses to the surface, and determined that it constitutes a new potential methodology to determine the behavior of the composite under the above conditions. The results demonstrated that the delamination areas on the PET facilitated polymer degradation by the electrolyte. Moreover, the Raman characterization evidenced the presence of multilayers and crystalline orderings, which limited its functionality as a protective coating.

  10. The composition of the modern juvenile arc crust and the nature of crustal delaminates in arcs (Invited)

    Science.gov (United States)

    Jagoutz, O. E.; Schmidt, M. W.

    2010-12-01

    The intraoceanic Kohistan arc, northern Pakistan, exposes a complete crustal section encompassing infracrustal cumulates formed at ≥ 55 km depth, a broadly basaltic/gabbroic lower crust, a 26 km thick calc-alkaline batholith, and 4 km of a volcanoclastic/sedimentary sequence. The bulk composition of the Kohistan arc crust has been approximated by estimating the relative volumes of exposed rocks through detailed field observations in combination with geobarometric constrains of the units' thicknesses and satellite images for lateral extension. We separated the arc in 3 major lower, mid-, and mid- to upper crustal units containing 14 subunits which compositions were derived from averaging 562 whole rock analyses. The details of the resulting bulk composition depend slightly on the method of integration, but all models yield andesitic bulk supra MOHO compositions. The Kohistan bulk arc composition results very similar to global continental crust estimates indicating that modern arc activity is the dominant process that formed the (preserved) continental crust. Fitting the bulk Kohistan arc crust and the ultramafic cumulates exposed at base of the arc (dunites, wehrlites, websterites, cpx-bearing garnetites and hornblendites, and garnet gabbros) to primitive arc melts with calc-alkaline/tholeiitic, alkaline, and boninitic affinity from various island arcs demonstrates that delamination of wehrlites + garnet hornblendites ± garnet gabbros perfectly explains the evolution from a tholeiitic/calc-alkaline primitive high-Mg basalt to the continental crust. Mass balance demonstrates that volumes of delaminate similar to the continental crust are required. Compared to depleted mantle, the delaminate is enriched in K, Cs, Ba and Pb and depleted in Zr and Th. It has further a subchondritic Nb/Ta and the high Pb and low U concentrations lead to a very unradiogenic Pb isotopy that may compensate for the depleted mantle Our results document that infra arc processes even in a

  11. Revisiting the Numerical Convergence of Cohesive-Zone Models in Simulating the Delamination of Composite Adhesive Joints by Using the Finite-Element Analysis

    Science.gov (United States)

    Liu, P. F.; Gu, Z. P.; Hu, Z. H.

    2016-11-01

    Delamination is the dominating failure mechanism in composite adhesive joints. A deep insight into the delamination failure mechanism requires advanced numerical methods. Currently, cohesive-zone models (CZMs), in combination with the finite-element analysis (FEA), have become powerful tools for modeling the initiation and growth of delaminations in composites. However, ensuring the numerical convergence in the CZMs used for a delamination analysis of three-dimensional (3D) composite structures is always a challenging issue due to the "snap-back" instability in the nonlinear implicit FEA, which arises mainly from the cohesive softening behavior. Based on the midplane interpolation technique, first numerical techniques for implementing 3D bilinear and exponential CZMs by using ABAQUS-UEL (user element subroutine) are developed in this paper. In particular, a viscous regularization by introducing the damping effect into the stiffness equation is used to improve the convergence. Two examples, a single-lap composite joint and a composite skin/stiffener panel under tension, demonstrate the numerical technique developed. Then, the effect of cohesion parameters on the numerical convergence based on the viscous regularization is studied.

  12. Effects of stitch density and stitch thread thickness on mode II delamination properties of Vectran stitched composites

    KAUST Repository

    Herwan, J.

    2014-11-01

    © Institute of Materials, Minerals and Mining 2014. Mode II delamination properties of Vectran stitched composites were investigated, and tabbed end notch flexural specimen testing was used to prevent premature failure. The effects of stitch density and stitch thread thickness were explored, and fibre compaction due to the stitching process was also verified. The results show that, in moderately stitched laminates (low stitch density), the improvement in GIIC was negligible. Crack bridging by the stitch threads at the crack zone were mostly compensated for the effect of fibre compaction, which reduced the GIIC values. Conversely, in densely stitched laminates (high stitch density), GIIC values were improved significantly (2·4 times higher than those of unstitched laminates). The effects of stitch thread thickness appeared to be negligible in moderately stitched laminates. For densely stitched laminates, thicker stitch thread (500 denier) possessed GIIC values that were 45·7% higher than thinner stitch thread (200 denier).

  13. In Search of a Time Efficient Approach to Crack and Delamination Growth Predictions in Composites

    Science.gov (United States)

    Krueger, Ronald; Carvalho, Nelson

    2016-01-01

    Analysis benchmarking was used to assess the accuracy and time efficiency of algorithms suitable for automated delamination growth analysis. First, the Floating Node Method (FNM) was introduced and its combination with a simple exponential growth law (Paris Law) and Virtual Crack Closure technique (VCCT) was discussed. Implementation of the method into a user element (UEL) in Abaqus/Standard(Registered TradeMark) was also presented. For the assessment of growth prediction capabilities, an existing benchmark case based on the Double Cantilever Beam (DCB) specimen was briefly summarized. Additionally, the development of new benchmark cases based on the Mixed-Mode Bending (MMB) specimen to assess the growth prediction capabilities under mixed-mode I/II conditions was discussed in detail. A comparison was presented, in which the benchmark cases were used to assess the existing low-cycle fatigue analysis tool in Abaqus/Standard(Registered TradeMark) in comparison to the FNM-VCCT fatigue growth analysis implementation. The low-cycle fatigue analysis tool in Abaqus/Standard(Registered TradeMark) was able to yield results that were in good agreement with the DCB benchmark example. Results for the MMB benchmark cases, however, only captured the trend correctly. The user element (FNM-VCCT) always yielded results that were in excellent agreement with all benchmark cases, at a fraction of the analysis time. The ability to assess the implementation of two methods in one finite element code illustrated the value of establishing benchmark solutions.

  14. Evaluation of Delamination Growth Characterization Methods Under Mode I Fatigue Loading

    Science.gov (United States)

    Murri, Gretchen B.

    2012-01-01

    Reliable delamination characterization data for laminated composites are needed for input to analytical models of structures to predict delamination. The double-cantilevered beam (DCB) specimen is used with laminated composites to measure fracture toughness, G(sub Ic), delamination onset strain energy release rate, and growth rate data under cyclic loading. In the current study, DCB specimens of IM7/8552 graphite/epoxy supplied by two different manufacturers were tested in static and fatigue to compare the measured characterization data from the two sources, and to evaluate a proposed ASTM standard for generating Paris Law equations. Static results were used to generate compliance calibration constants for the fatigue data, and a delamination resistance curve, G(sub IR), which was used to determine the effects of fiber-bridging on delamination growth. Specimens were tested in fatigue at a cyclic G(sub Imax) level equal to 50, 40 or 30% of G(sub Ic), to determine a delamination onset curve and delamination growth rate. The delamination onset curve equations had similar exponents and the same trends. Delamination growth rate was calculated by fitting a Paris Law to the da/dN versus G(sub Imax) data. Both a 2-point and a 7-point data reduction method were used and the Paris Law equations were compared. To determine the effects of fiber-bridging, growth rate results were normalized by the delamination resistance curve for each material and compared to the non-normalized results. Paris Law exponents were found to decrease by 31% to 37% due to normalizing the growth data. Normalizing the data also greatly reduced the amount of scatter between the different specimens. Visual data records from the fatigue testing were used to calculate individual compliance calibration constants from the fatigue data for some of the specimens. The resulting da/dN versus G(sub Imax) plots showed much improved repeatability between specimens. Gretchen

  15. Edge effects and delamination failures

    Science.gov (United States)

    Herakovich, C. T.

    1989-01-01

    The fundamental relationship between the morphology of a composite laminate and the resulting free edge effects is explored and related to delamination failures. Cross-ply, angle-ply, and quasi-isotropic laminates are discussed in detail. It is shown that the local mismatch in elastic properties of adjacent layers and the global stacking sequence of a laminate both have a significant influence on the interlaminar stresses and delamination failures.

  16. Enhanced supercapacitive performance of delaminated two-dimensional titanium carbide/carbon nanotube composites in alkaline electrolyte

    Science.gov (United States)

    Yan, Pengtao; Zhang, Ruijun; Jia, Jin; Wu, Chao; Zhou, Aiguo; Xu, Jiang; Zhang, Xuesha

    2015-06-01

    MXenes, a new family of two-dimensional materials, are terminated by O, OH and F groups. The existence of the oxygen-containing functional groups indicates a potential application in supercapacitor based on a redox mechanism. However, the irreversible stacking of MXenes will lead to an insufficient utilization of these functional groups and thus a decrease in the supercapacitive performance. To solve the problem, we synthesized a composite material comprised of carbon nanotube (CNT) and Ti3C2 sheets (d-Ti3C2) delaminated from MXenes by ultrasonic stirring. The FTIR result suggests that the ultrasonication has no significant effect on the oxygen-containing functional groups. The resultant composites exhibit significantly higher volumetric capacitance and better capacitance retention (during 5-100 mv s-1) than d-Ti3C2. A highest volumetric capacitance of 393 F cm-3 at 5 mv s-1 in KOH electrolyte can be obtained when the weight ratio of d-Ti3C2 to CNT is 2:1. In addition, the volumetric capacitance has no significant degradation even after 10000 cycles in cycling stability test, showing an excellent cycling stability compared with metal oxides. These enhanced electrochemical performances can be ascribed to the introduction of CNTs, which impede the stacking of Ti3C2, enlarge the distance between Ti3C2 sheets and improve the electrical conductivity.

  17. Tunable and purified luminescence via energy transfer and delamination of LRH (R=Tb, Y) composites with 8-hydroxypyrene-1,3,6-trisulphonate.

    Science.gov (United States)

    Su, Feifei; Liu, Chenyu; Yang, Yan; Ma, Shulan; Sun, Genban; Yang, Xiaojing

    2017-06-15

    This work demonstrates tunable and purified luminescence via one-step delamination of HPTS/OS-LRH composites (HPTS is trisodium 8-hydroxy-pyrene-1,3,6-trisulphonate, OS is sodium salt of 1-octane sulfonic acid, LRH is layered rare-earth hydroxide, R=Tb, Y) along with energy transfer. The HPTSxOS1-x-LTbyY1-yH composites presented varied luminescence behavior depending on their physical state. In solid state, dual-color luminescence was observed: blue-dominant emissions (437nm) for HPTSxOS1-x-LTbH, and blue- (437nm) to green-dominant (516nm) luminescence for HPTS0.02OS0.98-LTbyY1-yH. In delaminated state in famamide, purified luminescence was present: pure blue emission (440nm) for HPTSxOS1-x-LTbH and HPTS0.02OS0.98-LTbyY1-yH (y≥0.5), while pure bluish-green emission (498nm) for HPTS0.02OS0.98-LTbyY1-yH (y≤0.3). Both the delamination of the composites and energy transfer from layer Tb(3+) to HPTS contributed to the blue luminescence. The intriguing energy transfer process between photoactive inorganic hosts and organic guests can be utilized to fabricate hybrid materials with superior luminescence property.

  18. In-situ SEM and Stereomicroscope Study Delamination Evolution of Glass Fabric Reinforced Polycarbonate Composite

    Institute of Scientific and Technical Information of China (English)

    WANG Jun-bo; LI Ying-ming; XUE Ji-wen; SUN Yong-qi; ZHENG Shui-rong; SUN Man-lin

    2002-01-01

    The main objective of this study is to investigate the dynamic processes of the interlaminar fracture of the glass woven fabric reinforced polycarbonate composites through in- situ observation of specimen under mode I loading by SEM and stereomicroscope. The results show that the evolution processes of interlaminar damage consist of micro-crack initiation, growth and coalescence and advance forward of the main crack tip. The mode of crack propagation in fabric composite observed here seem to be the propagation along interface, interface change and fabric separation.

  19. Effects of Crimped Fiber Paths on Mixed Mode Delamination Behaviors in Woven Fabric Composites

    Science.gov (United States)

    2016-09-01

    figure 3. The force was applied to the loading bar at a constant rate with respect to time. This type of loading is referred to as “ force -control... rate Gc_eff. Once this occurred, strain energy was released and crack growth developed . Failure was based on LEFM through the use of VCCT. The VCCT...Composites Paul V. Cavallaro Andrew W. Hulton NUWC Division Newport Melvin W. Jee U.S. Army Natick Soldier Research, Development & Engineering Center

  20. Delamination Detection Using Guided Wave Phased Arrays

    Science.gov (United States)

    Tian, Zhenhua; Yu, Lingyu; Leckey, Cara

    2016-01-01

    This paper presents a method for detecting multiple delaminations in composite laminates using non-contact phased arrays. The phased arrays are implemented with a non-contact scanning laser Doppler vibrometer (SLDV). The array imaging algorithm is performed in the frequency domain where both the guided wave dispersion effect and direction dependent wave properties are considered. By using the non-contact SLDV array with a frequency domain imaging algorithm, an intensity image of the composite plate can be generated for delamination detection. For the proof of concept, a laboratory test is performed using a non-contact phased array to detect two delaminations (created through quasi-static impact test) at different locations in a composite plate. Using the non-contact phased array and frequency domain imaging, the two impact-induced delaminations are successfully detected. This study shows that the non-contact phased array method is a potentially effective method for rapid delamination inspection in large composite structures.

  1. Improved Damage Resistant Composite Materials Incorporating Shape Memory Alloys

    Science.gov (United States)

    Paine, Jeffrey S. N.; Rogers, Craig A.

    1996-01-01

    Metallic shape memory alloys (SMA) such as nitinol have unique shape recovery behavior and mechanical properties associated with a material phase change that have been used in a variety of sensing and actuation applications. Recent studies have shown that integrating nitinol-SMA actuators into composite materials increases the composite material's functionality. Hybrid composites of conventional graphite/epoxy or glass/epoxy and nitinol-SMA elements can perform functions in applications where monolithic composites perform inadequately. One such application is the use of hybrid composites to function both in load bearing and armor capacities. While monolithic composites with high strength-to-weight ratios function efficiently as loadbearing structures, because of their brittle nature, impact loading can cause significant catastrophic damage. Initial composite failure modes such as delamination and matrix cracking dissipate some impact energy, but when stress exceeds the composite's ultimate strength, fiber fracture and material perforation become dominant. One of the few methods that has been developed to reduce material perforation is hybridizing polymer matrix composites with tough kevlar or high modulus polyethynylene plies. The tough fibers increase the impact resistance and the stiffer and stronger graphite fibers carry the majority of the load. Similarly, by adding nitinol-SMA elements that absorb impact energy through the stress-induced martensitic phase transformation, the composites' impact perforation resistance can be greatly enhanced. The results of drop-weight and high velocity gas-gun impact testing of various composite materials will be presented. The results demonstrate that hybridizing composites with nitinol-SMA elements significantly increases perforation resistance compared to other traditional toughening elements. Inspection of the composite specimens at various stages of perforation by optical microscope illustrates the mechanisms by which

  2. An Interface Damage Model for the Simulation of Delamination Under Variable-Mode Ratio in Composite Materials

    Science.gov (United States)

    Turon, Albert; Camanho, Pedro P.; Costa, Josep; Davila, Carlos G.

    2004-01-01

    A thermodynamically consistent damage model for the simulation of progressive delamination under variable mode ratio is presented. The model is formulated in the context of the Damage Mechanics (DM). The constitutive equations that result from the variation of the free energy with damage are used to model the initiation and propagation of delamination. A new delamination initiation criterion is developed to assure that the formulation can account for changes in the loading mode in a thermodynamically consistent way. Interfacial penetration of two adjacent layers after complete decohesion is prevented by the formulation of the free energy. The model is implemented into the commercial finite element code ABAQUS by means of a user-written decohesion element. Finally, the numerical predictions given by the model are compared with experimental results.

  3. Criteria for initiation of delamination in quasi-static punch-shear tests of a carbon-fiber composite material.

    Energy Technology Data Exchange (ETDEWEB)

    Chin, Eric Brian [Sandia National Lab. (SNL-CA), Livermore, CA (United States); English, Shawn Allen [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Briggs, Timothy [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2015-09-01

    V arious phenomenological delamination initiation criteria are analyzed in quasi - static punch - shear tests conducted on six different geometries. These six geometries are modeled and analyzed using elastic, large - deformation finite element analysis. Analysis output is post - processed to assess different delamination initiation criteria, and their applicability to each of the geometries. These criteria are compared to test results to assess whether or not they are appropriate based on what occurred in testing. Further, examinations of CT scans and ultrasonic images o f test specimens are conducted in the appendix to determine the sequence of failure in each test geometry.

  4. Adhesive-Bonded Composite Joint Analysis with Delaminated Surface Ply Using Strain-Energy Release Rate

    Science.gov (United States)

    Chadegani, Alireza; Yang, Chihdar; Smeltzer, Stanley S. III

    2012-01-01

    This paper presents an analytical model to determine the strain energy release rate due to an interlaminar crack of the surface ply in adhesively bonded composite joints subjected to axial tension. Single-lap shear-joint standard test specimen geometry with thick bondline is followed for model development. The field equations are formulated by using the first-order shear-deformation theory in laminated plates together with kinematics relations and force equilibrium conditions. The stress distributions for the adherends and adhesive are determined after the appropriate boundary and loading conditions are applied and the equations for the field displacements are solved. The system of second-order differential equations is solved to using the symbolic computation tool Maple 9.52 to provide displacements fields. The equivalent forces at the tip of the prescribed interlaminar crack are obtained based on interlaminar stress distributions. The strain energy release rate of the crack is then determined by using the crack closure method. Finite element analyses using the J integral as well as the crack closure method are performed to verify the developed analytical model. It has been shown that the results using the analytical method correlate well with the results from the finite element analyses. An attempt is made to predict the failure loads of the joints based on limited test data from the literature. The effectiveness of the inclusion of bondline thickness is justified when compared with the results obtained from the previous model in which a thin bondline and uniform adhesive stresses through the bondline thickness are assumed.

  5. Packaging issues: avoiding delamination.

    Science.gov (United States)

    Hall, R

    2005-10-01

    Manufacturers can minimise delamination occurrence by applying the appropriate packaging design and process features. The end user can minimise the impact of fibre tear and reduce subsequent delamination by careful package opening. The occasional inconvenient delamination is a small price to pay for the high level of sterility assurance that comes with the use of Tyvek.

  6. Erosion-resistant composite material

    Science.gov (United States)

    Finch, C.B.; Tennery, V.J.; Curlee, R.M.

    A highly erosion-resistant composite material is formed of chemical vapor-deposited titanium diboride on a sintered titanium diboride-nickel substrate. This material may be suitable for use in cutting tools, coal liquefaction systems, etc.

  7. Edge Delamination and Residual Properties of Drilled Carbon Fiber Composites with and without Short-Aramid-Fiber Interleaf

    Science.gov (United States)

    Sun, Zhi; Hu, Xiaozhi; Shi, Shanshan; Guo, Xu; Zhang, Yupeng; Chen, Haoran

    2016-10-01

    Edge delamination is frequently observed in carbon fiber reinforced plastic (CFRP) laminates after machining, due to the low fracture toughness of the resin interfaces between carbon fiber plies. In this study, the effects of incorporating tough aramid fibers into the brittle CFRP system are quantified by measuring the residual properties of bolted CFRP. By adding short-aramid-fiber interleaves in CFRP laminates, the residual tensile strength have been substantially increased by 14 % for twill-weave laminates and 45 % for unidirectional laminates respectively. Moreover, tensile failure was observed as the major mode of toughened laminates, in contrast to shear failure of plain laminates. The qualitative FEM results agreed well with the experimental results that edge delamination would cause relatively higher shear stress and therefore alter the failure mode from tensile failure to shear failure.

  8. Research in textile composites at KU, Leuven

    Science.gov (United States)

    Verpoest, Ignaas; Ivens, Jan; Willemvanvuure, Aart; Efstratiou, Vassilios

    1993-01-01

    An overview is presented of the research on textile composites at Katholieke Universiteit Leuven. Three dimensionally woven sandwich fabric preforms are investigated for delamination resistant sandwich structures, velvet woven 2.5 dimensional fabrics for delamination resistant laminates, and knitted fabrics with good drapability for laminates of complex shape.

  9. Simulation of Delamination Propagation in Composites Under High-Cycle Fatigue by Means of Cohesive-Zone Models

    Science.gov (United States)

    Turon, Albert; Costa, Josep; Camanho, Pedro P.; Davila, Carlos G.

    2006-01-01

    A damage model for the simulation of delamination propagation under high-cycle fatigue loading is proposed. The basis for the formulation is a cohesive law that links fracture and damage mechanics to establish the evolution of the damage variable in terms of the crack growth rate dA/dN. The damage state is obtained as a function of the loading conditions as well as the experimentally-determined coefficients of the Paris Law crack propagation rates for the material. It is shown that by using the constitutive fatigue damage model in a structural analysis, experimental results can be reproduced without the need of additional model-specific curve-fitting parameters.

  10. THE EFFECT OF SUPPORT PLATE ON DRILLING-INDUCED DELAMINATION

    Directory of Open Access Journals (Sweden)

    Navid Zarif Karimi

    2016-02-01

    Full Text Available Delamination is considered as a major problem in drilling of composite materials, which degrades the mechanical properties of these materials. The thrust force exerted by the drill is considered as the major cause of delamination; and one practical approach to reduce delamination is to use a back-up plate under the specimen. In this paper, the effect of exit support plate on delamination in twist drilling of glass fiber reinforced composites is studied. Firstly, two analytical models based on linear fracture mechanics and elastic bending theory of plates are described to find critical thrust forces at the beginning of crack growth for drilling with and without back-up plate. Secondly, two series of experiments are carried out on glass fiber reinforced composites to determine quantitatively the effect of drilling parameters on the amount of delamination. Experimental findings verify a large reduction in the amount of delaminated area when a back-up plate is placed under the specimen.

  11. Guided Wave Delamination Detection and Quantification With Wavefield Data Analysis

    Science.gov (United States)

    Tian, Zhenhua; Campbell Leckey, Cara A.; Seebo, Jeffrey P.; Yu, Lingyu

    2014-01-01

    Unexpected damage can occur in aerospace composites due to impact events or material stress during off-nominal loading events. In particular, laminated composites are susceptible to delamination damage due to weak transverse tensile and inter-laminar shear strengths. Developments of reliable and quantitative techniques to detect delamination damage in laminated composites are imperative for safe and functional optimally-designed next-generation composite structures. In this paper, we investigate guided wave interactions with delamination damage and develop quantification algorithms by using wavefield data analysis. The trapped guided waves in the delamination region are observed from the wavefield data and further quantitatively interpreted by using different wavenumber analysis methods. The frequency-wavenumber representation of the wavefield shows that new wavenumbers are present and correlate to trapped waves in the damage region. These new wavenumbers are used to detect and quantify the delamination damage through the wavenumber analysis, which can show how the wavenumber changes as a function of wave propagation distance. The location and spatial duration of the new wavenumbers can be identified, providing a useful means not only for detecting the presence of delamination damage but also allowing for estimation of the delamination size. Our method has been applied to detect and quantify real delamination damage with complex geometry (grown using a quasi-static indentation technique). The detection and quantification results show the location, size, and shape of the delamination damage.

  12. 湿热载荷下含损伤夹层板分层扩展判定分析%Delamination Growth of Composite Sandwich under Hygrothermal and Mechanical Loads

    Institute of Scientific and Technical Information of China (English)

    张志民; 李向阳

    2001-01-01

    The local buckling may occur in composite sandwich with delamination induced by impact damage. This often causes delamination growth and structure failure. The delamiantion growth is studied by using the variational method of moving boundary, and the formulas of energy release rate G along the delamination front are obtained. By employing Rayleigh-Ritz method, the hygrothermal effect on buckling character of composite sandwich plates containing delamination between two faceplate laminae is studied.%含面板内分层损伤的复合材料夹层板在承受压缩载荷时,很容易发生局部屈曲,导致分层扩展和结构失效,恶劣的湿热环境更是使之加剧.利用可动边界变分问题对分层扩展进行了分析,导出了分层边界的逐点能量释放率表达式,采用Rayleigh-Ritz法研究了任意的湿热环境对含损伤的复合材料夹层板分层扩展性能的影响.

  13. Volumetric characterization of delamination fields via angle longitudinal wave ultrasound

    Science.gov (United States)

    Wertz, John; Wallentine, Sarah; Welter, John; Dierken, Josiah; Aldrin, John

    2017-02-01

    The volumetric characterization of delaminations necessarily precedes rigorous composite damage progression modeling. Yet, inspection of composite structures for subsurface damage remains largely focused on detection, resulting in a capability gap. In response to this need, angle longitudinal wave ultrasound was employed to characterize a composite surrogate containing a simulated three-dimensional delamination field with distinct regions of occluded features (shadow regions). Simple analytical models of the specimen were developed to guide subsequent experimentation through identification of optimal scanning parameters. The ensuing experiments provided visual evidence of the complete delamination field, including indications of features within the shadow regions. The results of this study demonstrate proof-of-principle for the use of angle longitudinal wave ultrasonic inspection for volumetric characterization of three-dimensional delamination fields. Furthermore, the techniques developed herein form the foundation of succeeding efforts to characterize impact delaminations within inhomogeneous laminar materials such as polymer matrix composites.

  14. THRUST FORCE AND TORQUE IN DRILLING THE NATURAL FIBER REINFORCED POLYMER COMPOSITE MATERIALS AND EVALUATION OF DELAMINATION FACTOR FOR BONE GRAFT SUBSTITUTES -A WORK OF FICTION APPROACH

    Directory of Open Access Journals (Sweden)

    D. CHANDRAMOHAN

    2010-11-01

    Full Text Available This paper discusses about the Natural Fiber Reinforced Composite Materials contribution as bone implants. Biomaterial science is an interdisciplinary field that represents one of the most sophisticated trends in worldwide medical practice. In the last decades, researchers have developed new materials to improve the quality of human life. Owing to the frequent occurrence of bone fractures, it is important to develop a plate material for fixation on the fractured bone. These plate materials have to be lightweight, allow stiffness, and be biocompatible with humans. Drilling is the most frequently employed operation of secondary machining for fiber-reinforced materials, owing to the need for joining fractured bone by means of plate material in the field of orthopedics. An effort to utilize theadvantages offered by renewable resources for the development of biocomposite materials based on biopolymers and natural fibers has been made through fabrication of Natural fiber powdered material (Sisal (Agave sisalana, Banana (Musa sepientum, and Roselle (Hibiscus sabdariffa reinforced polymer composite plate material by using bio epoxy resin Grade 3554A and Hardner 3554B. Instead of orthopedics alloys such as Titanium, Cobalt chrome, Stainless steel, and Zirconium, this plate material can be used for internal fixationand aso external fixation on human body for fractured bone. The present work focuses on the prediction of thrust force and torque of the natural fiber reinforced polymer composite materials, and the values, compared with the Regression model and the Scheme of Delamination factor / zone using machine vision system, also discussed with the help of Scanning Electron Microscope [SEM].

  15. Effect of Embedded Piezoelectric Sensors on Fracture Toughness and Fatigue Resistance of Composite Laminates Under Mode I Loading

    Science.gov (United States)

    Murri, Gretchen B.

    2006-01-01

    Double-cantilevered beam (DCB) specimens of a glass/epoxy composite material with embedded piezoelectric sensors were tested both statically and under fatigue loading to determine the effect of the embedded material on the Mode I fracture toughness and fatigue resistance compared to baseline data without the embedded elements. A material known as LaRC-Macrofiber Composite (LaRC-MFC (TradeMark)), or MFC, was embedded at the midplane of the specimen during the layup. Specimens were manufactured with the embedded MFC material either at the loaded end of the specimen to simulate an initial delamination; or with the MFC material located at the delaminating interface, with a Teflon film at the loaded end to simulate an initial delamination. There were three types of specimens with the embedded material at the delaminating interface: co-cured with no added adhesive; cured with a paste adhesive applied to the embedded element; or cured with a film adhesive added to the embedded material. Tests were conducted with the sensors in both the passive and active states. Results were compared to baseline data for the same material without embedded elements. Interlaminar fracture toughness values (G(sub Ic)) for the passive condition showed little change when the MFC was at the insert end. Passive results varied when the MFC was at the delaminating interface. For the co-cured case and with the paste adhesive, G(sub Ic) decreased compared to the baseline toughness, whereas, for the film adhesive case, G(sub Ic) was significantly greater than the baseline toughness, but the failure was always catastrophic. When the MFC was in the active state, G(sub Ic) was generally lower compared to the passive results. Fatigue tests showed little effect of the embedded material whether it was active or passive compared to baseline values.

  16. Delamination detection using methods of computational intelligence

    Science.gov (United States)

    Ihesiulor, Obinna K.; Shankar, Krishna; Zhang, Zhifang; Ray, Tapabrata

    2012-11-01

    Abstract Reliable delamination prediction scheme is indispensable in order to prevent potential risks of catastrophic failures in composite structures. The existence of delaminations changes the vibration characteristics of composite laminates and hence such indicators can be used to quantify the health characteristics of laminates. An approach for online health monitoring of in-service composite laminates is presented in this paper that relies on methods based on computational intelligence. Typical changes in the observed vibration characteristics (i.e. change in natural frequencies) are considered as inputs to identify the existence, location and magnitude of delaminations. The performance of the proposed approach is demonstrated using numerical models of composite laminates. Since this identification problem essentially involves the solution of an optimization problem, the use of finite element (FE) methods as the underlying tool for analysis turns out to be computationally expensive. A surrogate assisted optimization approach is hence introduced to contain the computational time within affordable limits. An artificial neural network (ANN) model with Bayesian regularization is used as the underlying approximation scheme while an improved rate of convergence is achieved using a memetic algorithm. However, building of ANN surrogate models usually requires large training datasets. K-means clustering is effectively employed to reduce the size of datasets. ANN is also used via inverse modeling to determine the position, size and location of delaminations using changes in measured natural frequencies. The results clearly highlight the efficiency and the robustness of the approach.

  17. Detection de l'initiation de la delamination des materiaux composites par suivi de l'emission acoustique

    Science.gov (United States)

    Silversides, Ian

    Cette étude, basée sur la surveillance des ondes d'émission acoustique (E.A.), présente le développement d'une approche de prédiction de l'initiation de la délamination de pièces composites soumises à des chargements statiques et en fatigue. La surveillance des ondes d'E.A. fait parti d'un nombre restreint de méthodes pouvant détecter, en continu, l'apparition et la croissance de dommages dans les matériaux composites. L'approche est comparée à des méthodes conventionnelles ainsi qu'à une modélisation numérique pour des composites à fibre de carbone unidirectionnels et tissés, sur une gamme de rapports de mode mixte. Le présent mémoire met en lumière les différentes étapes abordées durant l'étude. L'utilisation des matériaux composites est mise en contexte au premier chapitre. La complexité des matériaux composites ainsi que la nécessité de modèles de prédiction fiables sont soulignées. Le deuxième chapitre contient une revue de la littérature et présente les outils disponibles pour analyser le délaminage et bâtir un modèle prédictif de sa propagation. Les sujets traités sont la délamination dans un contexte de mécanique de la rupture, la modélisation numérique d'une propagation de fissure, l'approche du monitorage par émission acoustique puis l'analyse fractographiques des surfaces de rupture. Les résultats des essais mécaniques et de la modélisation sont présentés sous forme d'article dans le troisième chapitre. Des essais statiques et en fatigue ont permis de calculer le taux de restitution d'énergie de déformation à l'initiation de la délamination selon des méthodes classiques pour ensuite les comparer à une méthode développée, basée sur le suivi des ondes d'émission acoustique. Une série d'essais de propagation de la délamination en fatigue ont permis d'observer des corrélations entre les émissions acoustiques, la longueur de la délamination, la vitesse de croissance des fissures et la s

  18. 合拢弯矩作用下复合材料曲梁突变屈曲的研究%Delamination Buckling of a Curved Composite Beam Subjected to a Closing Bending Moment

    Institute of Scientific and Technical Information of China (English)

    王玮波; R.; A.; SHENOI; 崔维成

    2006-01-01

    The snap buckling case in a curved composite beam under a closing bending moment is dealt with.A theoretical approach is developed for the non-linear problem of delamination buckling which is likely to occur in curved composite structures.The approach is based on large deflection characterisation of a curved beam,coupled with fracture mechanics concepts.The general solution is applied to analyse a special case in which delamination occurs very close to inner surface of the beam and snap buckling happens in this delaminated thin layer. The effect of the arc angle of delamination crack on the critical load is also studied.%研究了复合材料曲梁在受到合拢弯矩作用下发生的屈曲情况,并给出一种理论解析方法来分析这种很可能发生在复合材料弯曲结构中的脱层耦合屈曲问题.该方法是基于曲梁大变形理论及断裂力学而提出来的.文中并用该解析方法分析了一个特定的常见的情况,在该题例中脱层发生在非常靠近内表面处并且突变屈曲就发生在该薄脱层.在文中也对脱层裂纹的弧角对极限载荷的影响进行了研究.

  19. Optimum electrode configuration selection for electrical resistance change based damage detection in composites using an effective independence measure

    Science.gov (United States)

    Escalona, Luis; Díaz-Montiel, Paulina; Venkataraman, Satchi

    2016-04-01

    Laminated carbon fiber reinforced polymer (CFRP) composite materials are increasingly used in aerospace structures due to their superior mechanical properties and reduced weight. Assessing the health and integrity of these structures requires non-destructive evaluation (NDE) techniques to detect and measure interlaminar delamination and intralaminar matrix cracking damage. The electrical resistance change (ERC) based NDE technique uses the inherent changes in conductive properties of the composite to characterize internal damage. Several works that have explored the ERC technique have been limited to thin cross-ply laminates with simple linear or circular electrode arrangements. This paper investigates a method of optimum selection of electrode configurations for delamination detection in thick cross-ply laminates using ERC. Inverse identification of damage requires numerical optimization of the measured response with a model predicted response. Here, the electrical voltage field in the CFRP composite laminate is calculated using finite element analysis (FEA) models for different specified delamination size and locations, and location of ground and current electrodes. Reducing the number of sensor locations and measurements is needed to reduce hardware requirements, and computational effort needed for inverse identification. This paper explores the use of effective independence (EI) measure originally proposed for sensor location optimization in experimental vibration modal analysis. The EI measure is used for selecting the minimum set of resistance measurements among all possible combinations of selecting a pair of electrodes among the n electrodes. To enable use of EI to ERC required, it is proposed in this research a singular value decomposition SVD to obtain a spectral representation of the resistance measurements in the laminate. The effectiveness of EI measure in eliminating redundant electrode pairs is demonstrated by performing inverse identification of

  20. Detecting delaminations and disbondings on full-scale wing composite panel by guided waves based SHM system

    Science.gov (United States)

    Monaco, E.; Boffa, N. D.; Memmolo, V.; Ricci, F.; Maio, L.

    2016-04-01

    A full-scale lower wing panel made of composite material has been designed, manufactured and sensorised within the European Funded research project named SARISTU. The authors contributed to the whole development of the system, from design to implementation as well as to the impacts campaign phase where Barely Visible and Visible Damages (BVID and VID) are to be artificially induced on the panel by a pneumatic impact machine. This work summarise part of the experimental results related to damages production, their assessment by C-SCAN as reference NDT method as well as damage detection of delimitations by a guided waves based SHM. The SHM system is made by customized piezoelectric patches secondary bonded on the wing plate acting both as guided waves sources and receivers. The paper will deal mostly with the experimental impact campaign and the signal analyses carried out to extract the metrics more sensitive to damages induced. Image reconstruction of the damages dimensions and shapes will be also described based mostly on the combination of metrics maps over the plate partial surfaces. Finally a comparison of damages maps obtained by the SHM approach and those obtained by "classic" C-SCAN will be presented analyzing briefly pros and cons of the two different approached as a combination to the most effective structural maintenance scenario of a commercial aircraft.

  1. Effect of Sea Water on Drilling Processes of Glass Fibre Reinforced Epoxy Composite Materials to Analysis of Delamination Factor and Thrust Force

    Directory of Open Access Journals (Sweden)

    Patil Deogonda B

    2014-02-01

    Full Text Available Fiber reinforced polymer composites have gained substantial attention as engineering structural materials in automotive, marine and aircraft industry as well as in civil engineering applications. This is due to their outstanding mechanical properties, impact resistance, high durability and flexibility in design capabilities and light weight The present work describes the development and mechanical characterization of new polymer composites consisting of glass fiber reinforcement, epoxy resin and filler materials such as TiO2 and ZnS. The newly developed composites are characterized for their mechanical properties. The tests result have shown that higher the filler material volume percentage greater the strength for both TiO2 and ZnS filled glass epoxy composites, ZnS filled composite show more sustaining values than TiO2. The present work also describes the machining (drilling of GFRP composites with the help of Step drill of three sets, with three different speeds. The work has been carried out by immersion of GFRP composites in sea water for 8hrs, 16hrs and 24hrs duration and performed drilling operation. Results revealed that 8-4 mm step drill showed better machining characteristic than the other two 12-8mm and 10-6 mm step drills. GFRP composite, with ZnS filler material soaked in sea water for 16hrs duration had better machining capability. The ZnS Filled GFRP composites had better performance than TiO2 filled GFRP Composites.

  2. Delamination-Indicating Thermal Barrier Coatings

    Science.gov (United States)

    Eldridge, Jeffrey I.

    2007-01-01

    The risk of premature failure of thermal barrier coatings (TBCs), typically composed of yttria-stabilized zirconia (YSZ), compromises the reliability of TBCs used to provide thermal protection for turbine engine components. Unfortunately, TBC delamination proceeds well beneath the TBC surface and cannot be monitored by visible inspection. Nondestructive diagnostic tools that could reliably probe the subsurface damage state of TBCs would alleviate the risk of TBC premature failure by indicating when the TBC needs to be replaced before the level of TBC damage threatens engine performance or safety. To meet this need, a new coating design for thermal barrier coatings (TBCs) that are self-indicating for delamination has been successfully implemented by incorporating a europium-doped luminescent sublayer at the base of a TBC composed of YSZ. The luminescent sublayer has the same YSZ composition as the rest of the TBC except for the addition of low-level europium doping and therefore does not alter TBC performance.

  3. Impact resistance of fiber composites

    Science.gov (United States)

    Chamis, C. C.; Sinclair, J. H.

    1982-01-01

    Stress-strain curves are obtained for a variety of glass fiber and carbon fiber reinforced plastics in dynamic tension, over the stress-strain range of 0.00087-2070/sec. The test method is of the one-bar block-to-bar type, using a rotating disk or a pendulum as the loading apparatus and yielding accurate stress-strain curves up to the breaking strain. In the case of glass fiber reinforced plastic, the tensile strength, strain to peak impact stress, total strain and total absorbed energy all increase significantly as the strain rate increases. By contrast, carbon fiber reinforced plastics show lower rates of increase with strain rate. It is recommended that hybrid composites incorporating the high strength and rigidity of carbon fiber reinforced plastic with the high impact absorption of glass fiber reinforced plastics be developed for use in structures subjected to impact loading.

  4. Impact resistance of fiber composite blades used in aircraft turbine engines

    Science.gov (United States)

    Friedrich, L. A.; Preston, J. L., Jr.

    1973-01-01

    Resistance of advanced fiber reinforced epoxy matrix composite materials to ballistic impact was investigated as a function of impacting projectile characteristics, and composite material properties. Ballistic impact damage due to normal impacts, was classified as transverse (stress wave delamination and splitting), penetrative, or structural (gross failure). Steel projectiles were found to be gelatin ice projectiles in causing penetrative damage leading to reduced tensile strength. Gelatin and ice projectiles caused either transverse or structural damage, depending upon projectile mass and velocity. Improved composite transverse tensile strength, use of dispersed ply lay-ups, and inclusion of PRD-49-1 or S-glass fibers correlated with improved resistance of composite materials to transverse damage. In non-normal impacts against simulated blade shapes, the normal velocity component of the impact was used to correlate damage results with normal impact results. Stiffening the leading edge of simulated blade specimens led to reduced ballistic damage, while addition of a metallic leading edge provided nearly complete protection against 0.64 cm diameter steel, and 1.27 cm diameter ice and gelatin projectiles, and partial protection against 2.54 cm diameter projectiles of ice and gelatin.

  5. Integrated global digital image correlation for interface delamination characterization

    KAUST Repository

    Hoefnagels, Johan P.M.

    2013-07-23

    Interfacial delamination is a key reliability challenge in composites and micro-electronic systems due to (high-density) integration of dissimilar materials. Predictive finite element models are used to minimize delamination failures during design, but require accurate interface models to capture (irreversible) crack initiation and propagation behavior observed in experiments. Therefore, an Integrated Global Digital Image Correlation (I-GDIC) strategy is developed for accurate determination of mechanical interface behavior from in-situ delamination experiments. Recently, a novel miniature delamination setup was presented that enables in-situ microscopic characterization of interface delamination while sensitively measuring global load-displacement curves for all mode mixities. Nevertheless, extraction of detailed mechanical interface behavior from measured images is challenging, because deformations are tiny and measurement noise large. Therefore, an advanced I-GDIC methodology is developed which correlates the image patterns by only deforming the images using kinematically-admissible \\'eigenmodes\\' that correspond to the few parameters controlling the interface tractions in an analytic description of the crack tip deformation field, thereby greatly enhancing accuracy and robustness. This method is validated on virtual delamination experiments, simulated using a recently developed self-adaptive cohesive zone (CZ) finite element framework. © The Society for Experimental Mechanics, Inc. 2014.

  6. Bio-inspired impact-resistant composites.

    Science.gov (United States)

    Grunenfelder, L K; Suksangpanya, N; Salinas, C; Milliron, G; Yaraghi, N; Herrera, S; Evans-Lutterodt, K; Nutt, S R; Zavattieri, P; Kisailus, D

    2014-09-01

    Through evolutionary processes, biological composites have been optimized to fulfil specific functions. This optimization is exemplified in the mineralized dactyl club of the smashing predator stomatopod (specifically, Odontodactylus scyllarus). This crustacean's club has been designed to withstand the thousands of high-velocity blows that it delivers to its prey. The endocuticle of this multiregional structure is characterized by a helicoidal arrangement of mineralized fiber layers, an architecture which results in impact resistance and energy absorbance. Here, we apply the helicoidal design strategy observed in the stomatopod club to the fabrication of high-performance carbon fiber-epoxy composites. Through experimental and computational methods, a helicoidal architecture is shown to reduce through-thickness damage propagation in a composite panel during an impact event and result in an increase in toughness. These findings have implications in the design of composite parts for aerospace, automotive and armor applications.

  7. Effect of Fiber Layers on the Fracture Resistance of Fiber Reinforced Composite Bridges

    Directory of Open Access Journals (Sweden)

    A Fazel

    2011-08-01

    Full Text Available Introduction: The purpose of this in vitro study was to introduce the fiber reinforced composite bridges and evaluate the most suitable site and position for placement of fibers in order to get maximum strength. Methods: The study included 20 second premolars and 20 second molars selected for fabricating twenty fiber reinforced composite bridges. Twenty specimens were selected for one fiber layer and the remaining teeth for two fiber layers. In the first group, fibers were placed in the inferior third and in the second group, fibers were placed in both the middle and inferior third region. After tooth preparation, the restorations were fabricated, thermocycled and then loaded with universal testing machine in the middle of the pontics with crosshead speed of 1mm/min. Data was analyzed by Kolmogorov-Smirnov test, Independent sample t test and Kaplan-Meier test. Mode of failure was evaluated using stereomicroscope. Results: Mean fracture resistance for the first and second groups was 1416±467N and 1349±397N, respectively. No significant differences were observed between the groups (P>0.05.In the first group, 5 specimens had delamintation and 5 specimens had detachment between fibers and resin composite. In the second group, there were 4 and 6 delaminations and detachments, respectively. There was no fracture within the fiber. Conclusion: In the fiber reinforced fixed partial dentures, fibers reinforce the tensile side of the connectors but placement of additional fibers at other sites does not increase the fracture resistance of the restoration.

  8. 含分层损伤缝合复合材料层板的剩余压缩强度%Prediction of Residual Compressive Strength of Stitched Composite Laminates with a Delamination

    Institute of Scientific and Technical Information of China (English)

    孙浩; 许希武; 郭树祥

    2012-01-01

    Based on a progressive damage method, the mechanical behaviors of stitched composite laminates containing initial delamination were investigated. A finite element (FE) model was established to predict the residual compressive strength through ABAQUS. Laminate buckling and delamination propagation were considered during the analytical process. The failures of laminates , interlaminar and stitching were simulated by UMAT subroutine embedded truss elements were used to provide the bridge-forces of stitching. Hashin criterion and stiffness reduction method were introduced to predict fiber failure and matrix failure. The progressive damage process was investigated and the damage mechanisms were analyzed in detail. Effects of different stitching parameters on residual compressive strength were discussed. The predicted failure modes and strength have excellent agreement with experimental results. It shows that stitching increases laminate buckling load-capacity, restrains delamination propagation and increases the residual compressive strength.%基于渐进损伤方法,研究了含单脱层缝合复合材料层板在压缩载荷下的剩余强度。通过商用软件ABAQUS建立了含单脱层缝合复合材料层板剩余压缩强度计算模型,考虑了子层屈曲和分层扩展对剩余强度的影响。通过UMAT子程序实现了层板失效、层间失效和缝线失效的模拟。通过嵌入式杆单元结构模拟了缝线桥联作用及失效。采用Hashin准则及刚度折减法对纤维拉压、基体拉压失效进行了模拟。通过渐进损伤分析,揭示了缝合情况下含单脱层复合材料层板的失效机理,讨论了缝合参数对剩余压缩强度的影响。所预测的破坏模式和剩余强度结果与实验能较好地吻合。分析表明缝合可以明显提高含分层损伤复合材料层板的子层屈曲载荷,抑制分层扩展,并提高层板的剩余压缩强度。

  9. Nanotube attachment for prevention of interfacial delamination

    Science.gov (United States)

    Mukhopadhyay, Sharmila M.; Karumuri, Anil K.

    2010-09-01

    A new approach to suppressing interfacial delamination in composites has been investigated. It involves growing strongly attached nanotubes on the surface of the core phase prior to matrix infiltration. Unusually durable interfaces between epoxy and graphite have been demonstrated using this technique. Two types of graphitic core materials have been studied: complex cellular foams having open-interconnected porosity and highly oriented pyrolitic graphite (HOPG) providing a model flat interface. When untreated foam is infiltrated with epoxy, the resulting composite is brittle, and shatters before 10% compression. However, when carbon nanotubes (CNTs) are grown on the foam prior to epoxy infiltration, the specimen becomes pliable, and visibly flattens out rather than fracturing. Model studies on a flat graphite-epoxy interface were performed by joining two HOPG specimens with a thin layer of epoxy, and testing the flexural response of the 'seam' using the three-point bend test. The untreated HOPG sandwich fails easily, whereas nanotube-attached HOPG sandwich shows an over three times increase in flexural load-carrying capacity, close to that of seamless monolithic graphite having identical dimensions. Microscopic evaluations of fractured interfaces indicate that, in all geometries, CNT grafting prevents delamination at the graphite-epoxy interface, and forces any crack(s) to propagate through the graphitic phase. This added inter-laminar strength and toughness can be related to the hierarchical morphology of the interface created by CNT attachment, and unprecedented composite structures can be envisioned.

  10. Thermally induced delamination of multilayers

    DEFF Research Database (Denmark)

    Sørensen, Bent F.; Sarraute, S.; Jørgensen, O.

    1998-01-01

    Steady-state delamination of multilayered structures, caused by stresses arising during processing due to thermal expansion mismatch, is analyzed by a fracture mechanics model based on laminate theory. It is found that inserting just a few interlayers with intermediate thermal expansion coefficie...... coefficients may be an effective way of reducing the delamination energy release rate. Uneven layer thickness and increasing elastic mismatch are shown to raise the energy release rate. Experimental work confirms important trends of the model.......Steady-state delamination of multilayered structures, caused by stresses arising during processing due to thermal expansion mismatch, is analyzed by a fracture mechanics model based on laminate theory. It is found that inserting just a few interlayers with intermediate thermal expansion...

  11. Modeling Quasi-Static and Fatigue-Driven Delamination Migration

    Science.gov (United States)

    De Carvalho, N. V.; Ratcliffe, J. G.; Chen, B. Y.; Pinho, S. T.; Baiz, P. M.; Tay, T. E.

    2014-01-01

    An approach was proposed and assessed for the high-fidelity modeling of progressive damage and failure in composite materials. It combines the Floating Node Method (FNM) and the Virtual Crack Closure Technique (VCCT) to represent multiple interacting failure mechanisms in a mesh-independent fashion. Delamination, matrix cracking, and migration were captured failure and migration criteria based on fracture mechanics. Quasi-static and fatigue loading were modeled within the same overall framework. The methodology proposed was illustrated by simulating the delamination migration test, showing good agreement with the available experimental data.

  12. Hypersonic Composites Resist Extreme Heat and Stress

    Science.gov (United States)

    2007-01-01

    Through research contracts with NASA, Materials and Electrochemical Research Corporation (MER), of Tucson, Arizona, contributed a number of technologies to record-breaking hypersonic flights. Through this research, MER developed a coating that successfully passed testing to simulate Mach 10 conditions, as well as provide several additional carbon-carbon (C-C) composite components for the flights. MER created all of the leading edges for the X-43A test vehicles at Dryden-considered the most critical parts of this experimental craft. In addition to being very heat resistant, the coating had to be very lightweight and thin, as the aircraft was designed to very precise specifications and could not afford to have a bulky coating. MER patented its carbon-carbon (C-C) composite process and then formed a spinoff company, Frontier Materials Corporation (FMC), also based in Tucson. FMC is using the patent in conjunction with low-cost PAN (polyacrylonitrile)-based fibers to introduce these materials to the commercial markets. The C-C composites are very lightweight and exceptionally strong and stiff, even at very high temperatures. The composites have been used in industrial heating applications, the automotive and aerospace industries, as well as in glass manufacturing and on semiconductors. Applications also include transfer components for glass manufacturing and structural members for carrier support in semiconductor processing.

  13. Melamine Polyimide Composite Fire Resistant Intumescent Coatings

    Directory of Open Access Journals (Sweden)

    Satish Chandra Gupta

    2013-07-01

    Full Text Available Components of intumescent coatings acid source, carbon source and blowing agent like melamine linked together by a binder provide cumulative fire retardant properties. When temperature of the coating surface reaches a critical temperature under the heat of flame, the surface begins to melt and is converted into highly viscous liquid. Simultaneously, reactions are initiated that result in the release of inert gases with low thermal conductivity. These gases are trapped inside the viscous fluid forming insulating char. The special composite of melamine polyimide, a C source and melamine a blowing agent showed high performance heat resistance in the present study. Polyimides have excellent heat and chemical resistance, excellent adhesion to a number of substrates and superior mechanical properties, such as high flexural modulus and compressive strength. Polyimides are also known to possess outstanding dimensional stability under loads, which allows their use in high temperature environments. Effect of the monomer on chemical reactivity between the binder and the intumescent additives has been studied by thermo-gravimetric analysis, differential scanning calorimeter and FTIR analysis. Thermal insulation studies by various intumescent composite coatings, applied on aluminium plates provided useful time temperature profiles.Defence Science Journal, 2013, 63(4, pp.442-446, DOI:http://dx.doi.org/10.14429/dsj.63.4871

  14. Melamine Polyimide Composite Fire Resistant Intumescent Coatings

    Directory of Open Access Journals (Sweden)

    Satish Chandra Gupta

    2013-07-01

    Full Text Available Components of intumescent coatings acid source, carbon source and blowing agent like melamine linked together by a binder provide cumulative fire retardant properties. When temperature of the coating surface reaches a critical temperature under the heat of flame, the surface begins to melt and is converted into highly viscous liquid. Simultaneously, reactions are initiated that result in the release of inert gases with low thermal conductivity. These gases are trapped inside the viscous fluid forming insulating char. The special composite of melamine polyimide, a C source and melamine a blowing agent showed high performance heat resistance in the present study. Polyimides have excellent heat and chemical resistance, excellent adhesion to a number of substrates and superior mechanical properties, such as high flexural modulus and compressive strength. Polyimides are also known to possess outstanding dimensional stability under loads, which allows their use in high temperature environments. Effect of the monomer on chemical reactivity between the binder and the intumescent additives has been studied by thermo-gravimetric analysis, differential scanning calorimeter and FTIR analysis. Thermal insulation studies by various intumescent composite coatings, applied on aluminium plates provided useful time temperature profiles.

  15. Failure mode research on CCF300 and T300 carbon fiber composite laminates with delamination under compressive strength%含分层损伤国产碳纤维CCF300与T300碳纤维复合材料层合板压缩失效模式

    Institute of Scientific and Technical Information of China (English)

    傅惠民; 杨雨松; 张勇波

    2011-01-01

    The compression test was conducted on the homemade and T300 carbon fiber composite laminate with one delamination.According to the macro-shape and the ultrasonic C-scan result of post-failure specimens which contain different sizes and different positions of delaminations but the same thickness,an investigation has been conducted by this study on the effects of delmaination sizes and positions on the failure mechanism of homemade and T300 carbon fiber composite laminates.Also the differences of failure mode have been analyzed between these two kinds of composites.The final result shows that the imbedded delaminations have all propagated,and the position of delamination proposed to be the most important factors affecting the compressive failure mode.To the laminates with deep delamination the failure mode presented to be the first propagation of delamination and second shear buckling failure of sub-laminate.Based on these analyses we find that the failure mode of homemade carbon fiber composite is same with the T300 carbon fiber composite generally.%对含单个分层损伤国产碳纤维CCF300与T300碳纤维复合材料层合板进行压缩试验,通过对同种中等厚度含不同分层大小、不同分层位置的层合板压缩失效后的宏微形貌及超声波C扫描检测结果的分析,研究了分层大小及分层位置对于国产碳纤维及T300纤维复合材料层合板失效模式造成的影响,比较了两种纤维复合材料失效模式的异同.结果表明,预制分层在压缩过程中都发生了扩展,而分层位置是影响其压缩失效模式较为重要的因素.对于分层位置较深的层合板,其失效模式往往为首先发生分层扩展,进而子层板剪切屈曲失效.总的分析表明,国产碳纤维复合材料与T300纤维复合材料含分层损伤层合板的压缩失效模式基本相同.

  16. Impact Resistance of Uncoated SiC/SiC Composites

    Science.gov (United States)

    Bhatt, Ramakrishna T.; Choi, Sung R.; Cosgriff, Laura M.; Fox, Dennis S.; Lee, Kang N.

    2008-01-01

    Two-dimensional woven SiC/SiC composites fabricated by melt infiltration method were impact tested at room temperature and at 1316 C in air using 1.59-mm diameter steel-ball projectiles at velocities ranging from 115 to 400 m/s. The extent of substrate damage with increasing projectile velocity was imaged and analyzed using optical and scanning electron microscopy, and non-destructive evaluation (NDE) methods such as pulsed thermography, and computed tomography. The impacted specimens were tensile tested at room temperature to determine their residual mechanical properties. Results indicate that at 115 m/s projectile velocity, the composite showed no noticeable surface or internal damage and retained its as-fabricated mechanical properties. As the projectile velocity increased above this value, the internal damage increased and mechanical properties degraded: At velocities >300 m/s, the projectile penetrated through the composite, but the composite retained approx.50% of the ultimate tensile strength of the as-fabricated composite and exhibited non-brittle failure. Predominant internal damages are delamination of fiber plies, fiber fracture and matrix shearing.

  17. Effects of voids on delamination behavior under static and fatigue mode I and mode II

    Science.gov (United States)

    Abdelal, Nisrin Rizek

    Composite materials have become materials of choice for wind turbine blade manufacturing due to their high specific stiffness, strength and fatigue life. Glass fiber composites are used extensively in light-weight structural components for wind turbines, aircrafts, marine craft and high performance automobile because glass fiber is inexpensive and usually provides high strength to weight ratio and good in-plane mechanical properties. The high cycle fatigue resistance of composite materials used in wind turbine blades has been recognized as a major uncertainty in predicting the reliability of wind turbines over their design lifetime. Blades are expected to experience 108 to 109 fatigue cycles over a 20 to 30 year lifetime. Delamination or interlaminar failure is a serious failure mode observed in composite structures. Even partial delamination will lead to a loss of local stiffness, which can preclude buckling failure. Manufacturing process defects such as voids and fiber waviness degrade the fatigue life and delamination resistance of the blade's composite. This research describes the effect of voids on static and fatigue interlaminar fracture behavior under mode I and mode II loading of wind turbine glass fiber composites. Samples with different void volume fractions in the 0.5%-7% range were successfully obtained by varying the vacuum in the hand layup vacuum bagging manufacturing process. Void content was characterized using four different methods; ultrasonic scanning, epoxy burn off, serial sectioning and X-Ray computed tomography. The effect of voids on both mode I and mode II interlaminar fracture toughness under static and fatigue loading was investigated. Finally, fractographic analysis (using optical and scanning electron microscopy) was conducted. The results showed that voids leads to slight reduction in static modes I and II interlaminar fracture toughness. In addition, voids lead to a decrease in modes I and II maximum cyclic strain energy release

  18. Assessment of Static Delamination Propagation Capabilities in Commercial Finite Element Codes Using Benchmark Analysis

    Science.gov (United States)

    Orifici, Adrian C.; Krueger, Ronald

    2010-01-01

    With capabilities for simulating delamination growth in composite materials becoming available, the need for benchmarking and assessing these capabilities is critical. In this study, benchmark analyses were performed to assess the delamination propagation simulation capabilities of the VCCT implementations in Marc TM and MD NastranTM. Benchmark delamination growth results for Double Cantilever Beam, Single Leg Bending and End Notched Flexure specimens were generated using a numerical approach. This numerical approach was developed previously, and involves comparing results from a series of analyses at different delamination lengths to a single analysis with automatic crack propagation. Specimens were analyzed with three-dimensional and two-dimensional models, and compared with previous analyses using Abaqus . The results demonstrated that the VCCT implementation in Marc TM and MD Nastran(TradeMark) was capable of accurately replicating the benchmark delamination growth results and that the use of the numerical benchmarks offers advantages over benchmarking using experimental and analytical results.

  19. HEAT-RESISTANT COMPOSITES CURED BY ELECTRON BEAM

    Institute of Scientific and Technical Information of China (English)

    Jian-wen Bao; Yang Li; Xiang-bao Chen; Feng-mei Li

    2001-01-01

    Electron beam (EB) curing of composites has many advantages. Heat-resistant EB-curing composites could substitute polyimide composites used in aeronautical engines. In this paper, the effects of catalyst and dose on the cured resin were investigated. The heat-resistance of the resin cured by EB was evaluated by dynamic mechanical analysis (DMA). The experimental results show that the mechanical properties of the composites cured by EB could meet the specifications of aeronautical engines at 250°C.

  20. The Delamination Theory of Wear

    Science.gov (United States)

    1974-09-01

    junctions, it is still based on the assumption that the deformation occurs at the asperities. Rabinowicz [14] advanced an adhesion theory of friction...shown that bronze particles were indeed bigger than steel particles. The compilation of wear particle sizes given by Rabinowicz [14] also indicates...Waterhouse [32] has shown that, in fact, fretting occurs by delamination. 6) Minimum Load for Loose Particle Formation Rabinowicz [14] found that no wear

  1. Shear-resistant behavior of light composite shear wall

    Institute of Scientific and Technical Information of China (English)

    李升才; 董毓利

    2015-01-01

    Shear test results for a composite wall panel in a light composite structure system are compared with test results for shear walls in Japan. The analysis results show that this kind of composite wall panel works very well, and can be regarded as a solid panel. The composite wall panel with a hidden frame is essential for bringing its effect on shear resistance into full play. Comprehensive analysis of the shear-resistant behavior of the composite wall panel suggests that the shear of the composite shear wall panel can be controlled by the cracking strength of the web shearing diagonal crack.

  2. Shear-Resistant Behavior Analysis of Light Composite Shear Walls

    Institute of Scientific and Technical Information of China (English)

    李升才; 江见鲸; 于庆荣

    2002-01-01

    Shear test results for a composite wall panel in a light composite structure system are compared with test results for shear walls in Japan in this paper. The analysis results show that this kind of composite wall panel works very well, and can be regarded as a solid panel. The composite wall panel with a hidden frame is essential for bringing its effect on shear resistance into full play. Comprehensive analysis of the shear-resistant behavior of the composite wall panel suggests that the shear of the composite shear wall panel can be controlled by the cracking strength of the web shearing diagonal crack.

  3. Evaluation of Delamination Onset and Growth Characterization Methods under Mode I Fatigue Loading

    Science.gov (United States)

    Murri, Gretchen B.

    2013-01-01

    Double-cantilevered beam specimens of IM7/8552 graphite/epoxy from two different manufacturers were tested in static and fatigue to compare the material characterization data and to evaluate a proposed ASTM standard for generating Paris Law equations for delamination growth. Static results were used to generate compliance calibration constants for reducing the fatigue data, and a delamination resistance curve, GIR, for each material. Specimens were tested in fatigue at different initial cyclic GImax levels to determine a delamination onset curve and the delamination growth rate. The delamination onset curve equations were similar for the two sources. Delamination growth rate was calculated by plotting da/dN versus GImax on a log-log scale and fitting a Paris Law. Two different data reduction methods were used to calculate da/dN. To determine the effects of fiber-bridging, growth results were normalized by the delamination resistance curves. Paris Law exponents decreased by 31% to 37% after normalizing the data. Visual data records from the fatigue tests were used to calculate individual compliance constants from the fatigue data. The resulting da/dN versus GImax plots showed improved repeatability for each source, compared to using averaged static data. The Paris Law expressions for the two sources showed the closest agreement using the individually fit compliance data.

  4. Delaminated rotator cuff tear: extension of delamination and cuff integrity after arthroscopic rotator cuff repair.

    Science.gov (United States)

    Gwak, Heui-Chul; Kim, Chang-Wan; Kim, Jung-Han; Choo, Hye-Jeung; Sagong, Seung-Yeob; Shin, John

    2015-05-01

    The purpose of this study was to evaluate the extension of delamination and the cuff integrity after arthroscopic repair of delaminated rotator cuff tears. Sixty-five patients with delaminated rotator cuff tears were retrospectively reviewed. The delaminated tears were divided into full-thickness delaminated tears and partial-thickness delaminated tears. To evaluate the medial extension, we calculated the coronal size of the delaminated portion. To evaluate the posterior extension, we checked the tendon involved. Cuff integrity was evaluated by computed tomography arthrography. The mean medial extension in the full-thickness and partial-thickness delaminated tears was 18.1 ± 6.0 mm and 22.7 ± 6.3 mm, respectively (P = .0084). The posterior extension into the supraspinatus and the infraspinatus was 36.9% and 32.3%, respectively, in the full-thickness delaminated tears, and it was 27.7% and 3.1%, respectively, in the partial-thickness delaminated tears (P = .0043). With regard to cuff integrity, 35 cases of anatomic healing, 10 cases of partial healing defects, and 17 cases of retear were detected. Among the patients with retear and partial healing of the defect, all the partially healed defects showed delamination. Three retear patients showed delamination, and 14 retear patients did not show delamination; the difference was statistically significant (P = .0001). The full-thickness delaminated tears showed less medial extension and more posterior extension than the partial-thickness delaminated tears. Delamination did not develop in retear patients, but delamination was common in the patients with partially healed defects. Copyright © 2015 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

  5. Wear resistance and corrosion resistance of VCp particle reinforced stainless steel composites

    Institute of Scientific and Technical Information of China (English)

    YAO Xiu-rong; HAN Jie-cai; ZUO Hong-bo; LIU Zhao-jing; LI Feng-zhen; REN Shan-zhi

    2005-01-01

    The VCp reinforced stainless steel composite was produced by in-situ reaction casting. The composite was tested for its wear resistance under the wet abrasive condition and corrosion resistance, compared with the wear-resistant white iron and stainless steel. The results show that the wear resistance of the composite is slightly inferior to that of the white iron, but much better than that of the stainless steel under the wet grinding abrasive condition. The corrosion resistance of the composite is much better than that of the white iron in the acid medium,and a little worse than that of the stainless steel. Thus the composite exhibits superior properties of wear resistance and corrosion resistance.

  6. Regional adaptive delaminating algorithm for rapid prototyping

    Institute of Scientific and Technical Information of China (English)

    CAI Daosheng; SHI Yusheng; HUANG Shuhuai

    2005-01-01

    With the development of rapid prototyping (RP) technology, the contradiction between fabricating speed and precision becomes more and more acute. In order to solve the contradiction, a regional effective adaptive delaminating algorithm is proposed in this paper. It is different from the traditional method that the regional adaptive delaminating method divides slicing contours into several regions and adaptively delaminates in respective region only according to the contours information. Namely, this method can not only adaptively delaminate at different height of CAD model but also adaptively delaminate different regions in one slicing layer. Furthermore, because the two-dimensional contour data adopted in this method are necessary for rapid prototyping system, this regional effective adaptive delaminating method is suitable for all RP systems. A comparative study is used to analyze the effectiveness of this method, which can demonstrate that this method can increase the fabricating speed and reduce the running cost under the condition of ensuring fabricating precision.

  7. Heat-Resistant Composite Materials Based on Polyimide Matrix

    Directory of Open Access Journals (Sweden)

    Vitaly Sergeyevich Ivanov

    2016-12-01

    Full Text Available Heat-resistant composite materials with a polyimide-based binder were obtained in this paper. Composites were prepared with different content of single-wall carbon nanotubes (SWCNT and nanostructured silicon carbide, and polyimides coated carbon fibers woven into the cloth. Composite materials showed high values of thermostability and resistance to thermo-oxidative degradation, as well as good mechanical properties.

  8. Resistivity of pristine and intercalated graphite fiber epoxy composites

    Science.gov (United States)

    Gaier, James R.; Hambourger, Paul D.; Slabe, Melissa E.

    1991-01-01

    Laminar composites were fabricated from pristine and bromine intercalated Amoco P-55, P-75, and P-100 graphite fibers and Hysol-Grafil EAG101-1 film epoxy. The thickness and r.f. eddy current resistivity of several samples were measured at grid points and averaged point by point to obtain final values. Although the values obtained this way have high precision (less than 3 percent deviation), the resistivity values appear to be 20 to 90 percent higher than resistivities measured on high aspect ratio samples using multi-point techniques, and by those predicted by theory. The temperature dependence of the resistivity indicates that the fibers are neither damaged nor deintercalated by the composite fabrication process. The resistivity of the composites is a function of sample thickness (i.e., resin content). Composite resistivity is dominated by fiber resistivity, so lowering the resistivity of the fibers, either through increased graphitization or intercalation, results in a lower composite resistivity. A modification of the simple rule of mixtures model appears to predict the conductivity of high aspect ratio samples measured along a fiber direction, but a directional dependence appears which is not predicted by the theory. The resistivity of these materials is clearly more complex than that of homogeneous materials.

  9. Free-edge delamination - Laminate width and loading conditions effects

    Science.gov (United States)

    Murthy, Pappu L. N.; Chamis, Christos C.

    1989-01-01

    The width and loading conditions effects on free-edge stress fields in composite laminates are investigated using a three-dimensional finite element analysis. This analysis includes a special free-edge region refinement or superelement with progressive substructuring (mesh refinement) and finite thickness interply layers. The different loading conditions include in-plane and out-of-plane bending, combined axial tension and in-plane shear, twisting, uniform temperature and uniform moisture. Results obtained indicate that: axial tension causes the smallest magnitude of interlaminar free edge stress compared to other loading conditions; free-edge delamination data obtained from laboratory specimens cannot be scaled to structural components; and composite structural components are not likely to delaminate.

  10. Free-edge delamination: Laminate width and loading conditions effects

    Science.gov (United States)

    Murthy, P. L. N.; Chamis, C. C.

    1987-01-01

    The width and loading conditions effects on free-edge stress fields in composite laminates are investigated using a three-dimensional finite element analysis. This analysis includes a special free-edge region refinement or superelement with progrssive substructuring (mesh refinement) and finite thickness interply layers. The different loading conditions include in-plane and out-of-plane bending, combined axial tension and in-plane shear, twisting, uniform temperature and uniform moisture. Results obtained indicate that: axial tension causes the smallest magnitude of interlaminar free edge stress compared to other loading conditions; free-edge delamination data obtained from laboratory specimens cannot be scaled to structural components; and composite structural components are not likely to delaminate.

  11. Delamination of Compressed Thin Layers at Corners

    DEFF Research Database (Denmark)

    Sørensen, Kim D.; Jensen, Henrik Myhre; Clausen, Johan

    2008-01-01

    An analysis of delamination for a thin elastic layer under compression, attached to a substrate at a corner is carried out. The analysis is performed by combining results from interface fracture mechanics and the theory of thin shells. In contrast with earlier results for delamination on a flat...... layers, Fracture mechanics, Crack closure, Steady state crack propagation....

  12. Delamination of Compressed Thin Layers at Corners

    DEFF Research Database (Denmark)

    Sørensen, Kim Dalsten; Jensen, Henrik Myhre; Clausen, Johan

    2008-01-01

    An analysis of delamination for a thin elastic layer under compression, attached to a substrate at a corner is carried out. The analysis is performed by combining results from interface fracture mechanics and the theory of thin shells. In contrast with earlier results for delamination on a flat...

  13. High temperature resistant cermet and ceramic compositions. [for thermal resistant insulators and refractory coatings

    Science.gov (United States)

    Phillips, W. M. (Inventor)

    1978-01-01

    High temperature oxidation resistance, high hardness and high abrasion and wear resistance are properties of cermet compositions particularly to provide high temperature resistant refractory coatings on metal substrates, for use as electrical insulation seals for thermionic converters. The compositions comprise a sintered body of particles of a high temperature resistant metal or metal alloy, preferably molybdenum or tungsten particles, dispersed in and bonded to a solid solution formed of aluminum oxide and silicon nitride, and particularly a ternary solid solution formed of a mixture of aluminum oxide, silicon nitride and aluminum nitride. Ceramic compositions comprising a sintered solid solution of aluminum oxide, silicon nitride and aluminum nitride are also described.

  14. Impact resistance of hybrid composite fan blade materials

    Science.gov (United States)

    Friedrich, L. A.

    1974-01-01

    Improved resistance to foreign object damage was demonstrated for hybrid composite simulated blade specimens. Transply metallic reinforcement offered additional improvement in resistance to gelatin projectile impacts. Metallic leading edge protection permitted equivalent-to-titanium performance of the hybrid composite simulated blade specimen for impacts with 1.27 cm and 2.54 cm (0.50 and 1.00 inch) diameter gelatin spheres.

  15. Aluminum Composites With Small Nanoparticles Additions: Corrosion Resistance

    OpenAIRE

    Agureev, L.E.; Kostikov, V.I.; Eremeeva, Zh.V.; Barmin, A.A.; Savushkina, S.V.; Ivanov, B.S.

    2016-01-01

    International audience; Research of corrosion resistance of the aluminum powder composites containing microadditives (0.01 – 0.15% is executed about.) zirconium oxide nanoparticles. Extreme dependence of speed of corrosion of aluminum composites in 10-% solutions of sulfuric and nitric acid from the maintenance of nanoadditives is shown. It has been shown the dynamics of mass loss of aluminum composites with nanoparticles of ZrO2 during corrosion tests in acids solutions. The lowest corrosion...

  16. THE INFLUENCE OF THE TOOL POINT ANGLE AND FEED RATE ON THE DELAMINATION AT DRILLING OF PRE-LAMINATED PARTICLEBOARD

    Directory of Open Access Journals (Sweden)

    Mihai ISPAS

    2015-12-01

    Full Text Available Pre-laminated particleboard is a wood based composite extensively used in the furniture industry. Drilling is the most common machining process which prepares the panels for joining using twist/helical drills in the absolute majority of cases. The point angle of the drill bit and the feed speed during drilling play a major role in gaining a good surface quality and minimizing the delamination tendency of the pre-laminated particleboard. The objective of this study was to measure and analyze the influence of the two above-mentioned factors on the processing quality, evaluated by de size of delaminations, both, at the entrance side and the exit side of the drill bit. To assess the defect, two parameters were used: the delamination factor and the effective area of delamination. The results showed that, in general, the combination of small point angle with low feed rate minimizes the delamination of pre-laminated particleboard panels at drilling.

  17. Creep behavior and wear resistance of Al 5083 based hybrid composites reinforced with carbon nanotubes (CNTs) and boron carbide (B{sub 4}C)

    Energy Technology Data Exchange (ETDEWEB)

    Alizadeh, Ali [Faculty of Materials & Manufacturing Processes, Malek-e-Ashtar University of Technology, Tehran (Iran, Islamic Republic of); Abdollahi, Alireza, E-mail: alirezaabdollahi1366@gmail.com [Faculty of Materials & Manufacturing Processes, Malek-e-Ashtar University of Technology, Tehran (Iran, Islamic Republic of); Biukani, Hootan [Faculty of Engineering, South Tehran Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of)

    2015-11-25

    In the current research, aluminum based hybrid composite reinforced with boron carbide (B{sub 4}C) and carbon nanotubes (CNTs) was produced by powder metallurgy method. creep behavior, wear resistance, surface roughness, and hardness of the samples were investigated. To prepare the samples, Al 5083 powder was milled with boron carbide particles and carbon nanotubes using planetary ball mill under argon atmosphere with ball-to-powder weight ratio of 10:1 for 5 h. Afterwards, the milled powders were formed by hot press process at 380{sup °}C and then were sintered at 585{sup °}C under argon atmosphere for 2 h. There was shown to be an increase in hardness values of composite with an increase in B{sub 4}C content. The micrograph of worn surfaces indicate a delamination mechanism due to the presence of CNTs and abrasion mechanism in composite containing 10 vol.%B{sub 4}C. Moreover, it was shown that increasing B{sub 4}C content increases the wear resistance by 3 times under a load of 20 N and 10 times under a load of 10 N compared to CNTs-reinforced composite. surface roughness of the composite containing 5 vol.%CNT has shown to be more than other samples. The results of creep test showed that adding carbon nanotubes increases creep rate of Al 5083 alloy; however, adding B{sub 4}C decreases its creep rate. - Highlights: • Al 5083/(CNTs + B{sub 4}C) hybrid composite was produced by powder metallurgy method. • Creep behavior, wear resistance, surface roughness, and Hardness of samples were investigated. • Addition of CNTs to Al 5083 matrix reduces alloy hardness, wear resistance and creep strength. • By addition of B{sub 4}C and composite hybridization, creep strength and wear resistance increased. • Surface roughness of Al-5 vol.%CNT has shown to be more than other samples.

  18. Investigation on low velocity impact resistance of SMA composite material

    Science.gov (United States)

    Hu, Dianyin; Zhang, Long; Wang, Rongqiao; Zhang, Xiaoyong

    2016-04-01

    A method to improve low velocity impact resistance of aeroengine composite casing using shape memory alloy's properties of shape memory(SM) and super-elasticity(SE) is proposed in this study. Firstly, a numerical modeling of SMA reinforced composite laminate under low velocity impact load with impact velocity of 10 m/s is established based on its constitutive model implemented by the VUMAT subroutine of commercial software ABAQUS. Secondly, the responses of SMA composite laminate including stress and deflection distributions were achieved through transient analysis under low velocity impact load. Numerical results show that both peak stress and deflection values of SMA composite laminate are less than that without SMA, which proves that embedding SMA into the composite structure can effectively improve the low velocity impact performance of composite structure. Finally, the influence of SM and SE on low velocity impact resistance is quantitatively investigated. The values of peak stress and deflection of SMA composite based on SM property decrease by 18.28% and 9.43% respectively, compared with those without SMA, instead of 12.87% and 5.19% based on SE. In conclusion, this proposed model described the impact damage of SMA composite structure and turned to be a more beneficial method to enhance the impact resistance by utilizing SM effect.

  19. Shape memory-based tunable resistivity of polymer composites

    Science.gov (United States)

    Luo, Hongsheng; Zhou, Xingdong; Ma, Yuanyuan; Yi, Guobin; Cheng, Xiaoling; Zhu, Yong; Zu, Xihong; Zhang, Nanjun; Huang, Binghao; Yu, Lifang

    2016-02-01

    A conductive composite in bi-layer structure was fabricated by embedding hybrid nanofillers, namely carbon nanotubes (CNTs) and silver nanoparticles (AgNPs), into a shape memory polyurethane (SMPU). The CNT/AgNP-SMPU composites exhibited a novel tunable conductivity which could be facially tailored in wide range via the compositions or a specifically designed thermo-mechanical shape memory programming. The morphologies of the conductive fillers and the composites were investigated by scanning electron microscope (SEM). The mechanical and thermal measurements were performed by tensile tests and differential scanning calorimetry (DSC). By virtue of a specifically explored shape memory programming, the composites were stretched and fixed into different temporary states. The electrical resistivity (Rs) varied accordingly, which was able to be stabilized along with the shape fixing. Theoretical prediction based upon the tunneling model was performed. The Rs-strain curves of the composites with different compositions were well fitted. Furthermore, the relative resistivity and the Gauge factor along with the elongation were calculated. The influence of the compositions on the strain-dependent Rs was disclosed. The findings provided a new avenue to tailor the conductivity of the polymeric nano-composites by combining the composition method and a thermo-mechanical programming, which may greatly benefit the application of intelligent polymers in flexible electronics and sensors fields.

  20. Composite capillary membrane for solvent resistant nanofiltration

    NARCIS (Netherlands)

    Dutczak, S.M.; Luiten-Olieman, Maria W.J.; Zwijnenberg, Harmen Jan; Bolhuis-Versteeg, Lydia A.M.; Winnubst, Aloysius J.A.; Hempenius, Mark A.; Benes, Nieck Edwin; Wessling, Matthias; Stamatialis, Dimitrios

    2011-01-01

    Solvent resistant nanofiltration (SRNF) is a membrane separation process allowing for an efficient separation of small molecules of 200–1000 g mol−1 from organic solvents. The application of SRNF in industry applications is currently hindered by a limited choice of SRNF membranes and configurations.

  1. Microleakage resistance of minimally invasive Class I flowable composite restorations.

    Science.gov (United States)

    Bonilla, Esteban D; Stevenson, Richard G; Caputo, Angelo A; White, Shane N

    2012-01-01

    Minimally invasive flowable composite Class I restorations are widely used. However, flowable composites are characterized by low filler contents, modified resin formulations, low moduli of elasticity, low viscosity, generally poor mechanical properties, and decreased long-term stability. The purpose of this study was to compare the microleakage resistance of a wide variety of flowable composites used with their manufacturers' recommended bonding systems to that of a long-used and widely studied microhybrid composite when placed as minimally invasive occlusal restorations. Molar teeth were prepared in a standardized manner, restored, artificially aged, stained, sectioned, evaluated, and analyzed. Microleakage varied substantially, by a whole order of magnitude, among the material groups tested. The control group, a conventional microhybrid composite material, leaked significantly less than all the flowable composite groups. Microleakage varied very slightly among measurement site locations. Tiny microscopic bubbles were seen within many of the flowable composite specimens, as were a few voids.

  2. Longitudinal shear resistance of composite slabs

    NARCIS (Netherlands)

    Schuurman, R.G.; Stark, J.W.B.

    1996-01-01

    Verification methods for longitudinal shear. currently in use, are empirical. This applies for both the m-k method as the Partial Shear Connection method. Parameters and mechanisms determining the behaviour of the shear connection in composite slabs are not directly considered in these methods. A

  3. Impact Resistance of Environmental Barrier Coated SiC/SiC Composites

    Science.gov (United States)

    Bhatt, Ramakrishna T.; Choi, Sung R.; Cosgriff, Laura M.; Fox, Dennis S.; Lee, Kang N.

    2008-01-01

    Impact performance of 2D woven SiC/SiC composites coated with 225 and 525 microns thick environmental barrier coating (EBC) was investigated. The composites were fabricated by melt infiltration and the EBC was deposited by plasma spray. Impact tests were conducted at room temperature and at 1316 C in air using 1.59 mm diameter steel-balls at projectile velocities ranging from 110 to 375 m/s . Both microscopy and non-destructive evaluation (NDE) methods were used to determine the extent of damage in the substrate and coating with increasing projectile velocity. The impacted specimens were tensile tested at room temperature to determine their residual mechanical properties. At projectile velocities less than 125 m/s , no detectable internal damage was noticed in the MI SiC/SiC composites coated with 525 microns EBC. With increase in projectile velocity beyond this value, spallation of EBC layers, delamination of fiber plies, and fiber fracture were detected. At a fixed projectile velocity, the composites coated with 525 microns EBC showed less damage than those coated with 225 microns EBC. Both types of coated composites retained a large fraction of the baseline properties of the as-fabricated composites and exhibited non-brittle failure after impact testing. Furnace exposure of impacted specimens in a moisture environment at 1316 C for 500 h indicated that the through-the-thickness cracks in the coating and delamination cracks in the substrate generated after impact testing acted as conduits for internal oxidation.

  4. Impact Resistance of Environmental Barrier Coated SiC/SiC Composites

    Science.gov (United States)

    Bhatt, Ramakrishna T.; Choi, Sung R.; Cosgriff, Laura M.; Fox, Dennis S.; Lee, Kang N.

    2008-01-01

    Impact performance of 2D woven SiC/SiC composites coated with 225 and 525 microns thick environmental barrier coating (EBC) was investigated. The composites were fabricated by melt infiltration and the EBC was deposited by plasma spray. Impact tests were conducted at room temperature and at 1316 C in air using 1.59 mm diameter steel-balls at projectile velocities ranging from 110 to 375 m/s . Both microscopy and non-destructive evaluation (NDE) methods were used to determine the extent of damage in the substrate and coating with increasing projectile velocity. The impacted specimens were tensile tested at room temperature to determine their residual mechanical properties. At projectile velocities less than 125 m/s , no detectable internal damage was noticed in the MI SiC/SiC composites coated with 525 microns EBC. With increase in projectile velocity beyond this value, spallation of EBC layers, delamination of fiber plies, and fiber fracture were detected. At a fixed projectile velocity, the composites coated with 525 microns EBC showed less damage than those coated with 225 microns EBC. Both types of coated composites retained a large fraction of the baseline properties of the as-fabricated composites and exhibited non-brittle failure after impact testing. Furnace exposure of impacted specimens in a moisture environment at 1316 C for 500 h indicated that the through-the-thickness cracks in the coating and delamination cracks in the substrate generated after impact testing acted as conduits for internal oxidation.

  5. Analysis of the Effect of Surface Modification on Polyimide Composites Coated with Erosion Resistant Materials

    Science.gov (United States)

    Ndalama, Tchinga; Hirschfeld, Deidre; Sutter, James K. (Technical Monitor)

    2003-01-01

    The aim of this research is to enhance performance of composite coatings through modification of graphite-reinforced polyimide composite surfaces prior to metal bond coat/ hard topcoat application for use in the erosive and/or oxidative environments of advanced engines. Graphite reinforced polyimide composites, PMR-15 and PMR-II-50, formed by sheet molding and pre-pregging will be surface treated, overlaid with a bond coat and then coated with WC-Co. The surface treatment will include cleaning, RF plasma or ultraviolet light- ozone etching, and deposition of SiO(x) groups. These surface treatments will be studied in order to investigate and improve adhesion and oxidation resistance. The following panels were provided by NASA-Glenn Research Center(NASA-GRC): Eight compression molded PMR-II-50; 6 x 6 x 0.125 in. Two vacuum-bagged PMR-II-50; 12 x 12 x 0.125 in. Eight compression molded PMR-15; 6 x 6 x 0.125 in. One vacuum-bagged PMR-15; 12 x 12 x 0.125 in. All panels were made using a 12 x 12 in. T650-35 8HS (3K-tow) graphite fabric. A diamond-wafering blade, with deionized water as a cutting fluid, was used to cut PMR-II-50 and PMR-15 panels into 1 x 1 in. pieces for surface tests. The panel edges exhibiting delamination were used for the preliminary surface preparation tests as these would be unsuitable for strength and erosion testing. PMR-15 neat resin samples were also provided by NASA GRC. Surface profiles of the as-received samples were determined using a Dektak III Surface profile measuring system. Two samples of compression molded PMR-II-50 and PMR-15, vacuum-bagged PMR-II-50 and PMR-15 were randomly chosen for surface profile measurement according to ANSI/ASME B46.1. Prior to each measurement, the samples were blasted with compressed air to remove any artifacts. Five 10 mm-long scans were made on each sample. The short and long wavelength cutoff filter values were set at 100 and 1000 m, diamond stylus radius was 12.5 microns. Table 1 is a summary of the

  6. Wear and impact resistance of HVOF sprayedceramic matrix composites coating

    Science.gov (United States)

    Prawara, B.; Martides, E.; Priyono, B.; Ardy, H.; Rikardo, N.

    2016-02-01

    Ceramic coating has the mechanical properties of high hardness and it is well known for application on wear resistance, but on the other hand the resistance to impact load is low. Therefore its use is limited to applications that have no impact loading. The aim of this research was to obtain ceramic-metallic composite coating which has improved impact resistance compared to conventional ceramic coating. The high impact resistance of ceramic-metallic composite coating is obtained from dispersed metallic alloy phase in ceramic matrix. Ceramic Matrix Composites (CMC) powder with chrome carbide (Cr3C2) base and ceramic-metal NiAl-Al2O3 with various particle sizes as reinforced particle was deposited on mild steel substrate with High Velocity Oxygen Fuel (HVOF) thermal spray coating. Repeated impact test showed that reinforced metallic phase size influenced impact resistance of CMC coating. The ability of CMC coating to absorb impact energy has improved eight times and ten times compared with original Cr3C2 and hard chrome plating respectively. On the other hand the high temperature corrosion resistance of CMC coating showed up to 31 cycles of heating at 800°C and water quenching cooling.

  7. Resistance Welding of Thermoplastic Composites: Process and Performance

    OpenAIRE

    Shi, H.

    2014-01-01

    Compared to thermoset composites, thermoplastic composites are drawing more and more attention by aircraft industries not only due to their excellent material properties but also due to their potentials to reduce cycle time and structure cost by using low-cost manufacturing technologies such as welding. Resistance welding has been regarded as one of the most promising welding techniques owing to the low energy consumption, simplicity of welding operation and capability for scaling up. Previou...

  8. Common bunt resistant wheat composite cross populations

    DEFF Research Database (Denmark)

    Steffan, Philipp Matthias; Borgen, A.; Backes, Gunter Martin

    stability. However, a number of challenges must be met before diverse wheat populations can be introduced into commercial wheat production: one of these is the development of breeding technologies based on mass selection which enable breeders and farmers to improve specific traits in populations...... and maintain diversity at the same time. BIOBREED is a project which commenced in Denmark in 2011 to meet these challenges for wheat population breeding. The project focuses on the development of tools and methods for mass selection of traits relevant for organic and low input production, where it is expected...... that the highest benefits of utilizing diverse populations can be achieved. BIOBREED focuses on three main aspects of wheat population breeding for organic and low input production systems: i) common bunt (caused by Tilletia caries) resistance, ii) selection for improved protein content and iii) the influence...

  9. Hierarchical fiber-optic delamination detection system for carbon fiber reinforced plastic structures

    Science.gov (United States)

    Minakuchi, Shu; Banshoya, Hidehiko; Shingo, Ii; Takeda, Nobuo

    2012-10-01

    This study develops a delamination detection system by extending our previous approach for monitoring surface cracks in a large-scale composite structure. In the new system, numerous thin glass capillaries are embedded into a composite structure, and internal pressure in the built-in capillary sensors, based on comparative vacuum monitoring (CVM), is maintained as a vacuum. When delamination is induced, the capillary sensors located within the delaminated area are breached, and atmospheric air flows into the capillaries. The consequent pressure change within the capillaries is then converted into axial strain in a surface-mounted optical fiber through a transducing mechanism, which is connected to the capillaries. By monitoring the strain distribution along the optical fiber, it is possible to identify a transducing mechanism in which the pressure change occurred and thus to specify the location of the delamination. This study begins by establishing a novel sensor embedding/extracting method. The airflow characteristic in the capillary sensors is then comprehensively evaluated, determining the basic performance of the new system. The proposed detection technique is validated by taking a step-by-step approach, and finally the hierarchical fiber-optic delamination detection system is demonstrated. A further advance to be combined with a self-healing concept is also discussed.

  10. Hydraulic resistance in part-full pipes with composite roughness

    DEFF Research Database (Denmark)

    Perrusquia, G.; Petersen, O.; Larsen, Torben

    1994-01-01

    The paper discusses the boundary shear stresses and the hydraulic resistance in part-full sewer pipes with composite roughness. The discussion is based on a series of numerical experiments using a validated numerical turbulence model. The results from the numerical model are compared...

  11. Electrodeposition and Corrosion Resistance of Ni-Graphene Composite Coatings

    Science.gov (United States)

    Szeptycka, Benigna; Gajewska-Midzialek, Anna; Babul, Tomasz

    2016-08-01

    The research on the graphene application for the electrodeposition of nickel composite coatings was conducted. The study assessed an important role of graphene in an increased corrosion resistance of these coatings. Watts-type nickel plating bath with low concentration of nickel ions, organic addition agents, and graphene as dispersed particles were used for deposition of the composite coatings nickel-graphene. The results of investigations of composite coatings nickel-graphene deposited from the bath containing 0.33, 0.5, and 1 g/dm3 graphene and one surface-active substance were shown. The contents of particles in coatings, the surface morphology, the cross-sectional structures of the coated samples, and their thickness and the internal stresses were studied. Voltammetric method was used for examination of the corrosion resistance of samples of composite coatings in 0.5 M NaCl. The obtained results suggest that the content of incorporated graphene particles increases with an increasing amount of graphene in plating bath. The application of organic compounds was advantageous because it caused compressive stresses in the deposited coatings. All of the nickel-graphene composite layers had better corrosion resistance than the nickel coating.

  12. The stab resistant properties of Kevlar/STF composites

    Science.gov (United States)

    Zhao, Jinhua; Cao, Hailin; Li, Xia; Wan, Junxi; Wang, Kun; Zhang, Jinfeng

    2012-04-01

    A colloidal shear thickening fluid (STF) was prepared by dispersing submicron silica particles in Polyethylene glycol 200(PEG200) with ball-milling technique. Kevlar/STF composites were fabricated by soaking Kevlar in the solution of STF diluted by ethanol. The rheological behavior of the fluid with various concentrations and the effect of dilution ratio on stab resistant properties of Kevlar/STF composites were studied. The result shows that the initial viscosity and the highest viscosity of the fluid increase as the weight fraction of SiO2 increasing with the weight fraction ranging from 50% to 60%, while the critical shear rate decrease as the weight fraction increasing. The fluid has notable shear thickening behavior at SiO2 weight fraction of 59%. Two solutions with 1:0.5 and 1:1weight ratio of STF:ethanol were used to fabricate Kevlar/STF composites. It is found that the composites fabricated by solution with dilution ratio 1:1 show better stab resistant properties. The Kevlar/STF composites exhibit better stab resistant properties than the neat Kevlar with the same areal density.

  13. Detecting Damage in Ceramic Matrix Composites Using Electrical Resistance

    Science.gov (United States)

    Smith, Craig E.; Gyekenyesi, Andrew

    2011-01-01

    The majority of damage in SiC/SiC ceramic matrix composites subjected to monotonic tensile loads is in the form of distributed matrix cracks. These cracks initiate near stress concentrations, such as 90 deg fiber tows or large matrix pores and continue to accumulate with additional stress until matrix crack saturation is achieved. Such damage is difficult to detect with conventional nondestructive evaluation techniques (immersion ultrasonics, x-ray, etc.). Monitoring a specimen.s electrical resistance change provides an indirect approach for monitoring matrix crack density. Sylramic-iBN fiber- reinforced SiC composites with a melt infiltrated (MI) matrix were tensile tested at room temperature. Results showed an increase in resistance of more than 500% prior to fracture, which can be detected either in situ or post-damage. A relationship between resistance change and matrix crack density was also determined.

  14. Detecting Cracks in Ceramic Matrix Composites by Electrical Resistance

    Science.gov (United States)

    Smith, Craig; Gyekenyesi, Andrew

    2011-01-01

    The majority of damage in SiC/SiC ceramic matrix composites subjected to monotonic tensile loads is in the form of distributed matrix cracks. These cracks initiate near stress concentrations, such as 90o fiber tows or large matrix pores and continue to accumulate with additional stress until matrix crack saturation is achieved. Such damage is difficult to detect with conventional nondestructive evaluation techniques (immersion ultrasonics, x-ray, etc.). Monitoring a specimen.s electrical resistance change provides an indirect approach for monitoring matrix crack density. Sylramic-iBN fiber- reinforced SiC composites with a melt infiltrated (MI) matrix were tensile tested at room temperature. Results showed an increase in resistance of more than 500% prior to fracture, which can be detected either in situ or post-damage. A relationship between resistance change and matrix crack density was also determined.

  15. Effect of composition on the polarization and ohmic resistances of LSM/YSZ composite cathodes in solid oxide fuel cell

    Indian Academy of Sciences (India)

    B SHRI PRAKASH; S SENTHIL KUMAR; S T ARUNA

    2017-06-01

    La0.8Sr0.2MnO$_3$−$\\delta$ (LSM)/8 mol% yttria-stabilized ZrO$_2$ (YSZ) (LSM/YSZ) composite cathodes with varying composition are studied for both polarization and ohmic resistance by electrochemical impedance spectroscopy. It was found that total resistance and polarization resistance are lowest for the composite with 60 wt% of LSM (LSM60/YSZ40). However, the ohmic resistance was highest for the same composition and amounted to 60% of the total resistance value. Compositional dependence of resistances has been explained based on the variations of the triple phase boundaries and width of the O$_2$−ion migration path with the composition of the electrode. Based on the observed area specific ohmic resistance values for the composite cathodes, it is proposed to verify the advantages of LSM/YSZ over LSM cathode in anode-supported solidoxide fuel cell with thin electrolyte.

  16. Orogenic delamination - dynamics, effects, and geological expression

    Science.gov (United States)

    Ueda, Kosuke; Gerya, Taras

    2010-05-01

    Unbundling of continental lithosphere and removal of its mantle portion have been described by two mutually rather exclusive models, convective thinning and integral delamination. Either disburdens the remaining lithosphere, weakens the remainder, and causes uplift and extension. Increased heat flux is likely to promote high-degree crustal melting, and has been viewed as a source for voluminous granitic intrusions in late or collapsing orogenic settings. Collapse may be driven by any of gravitational potential differences from orogen to foreland, by stress inversion in the unburdened domain, or by suction of a retreating trench. In this study, we investigate prerequisites, mechanism, and development paths for orogeny-related mantle lithosphere removal. Our experiments numerically reproduce delamination which self-consistently results from the dynamics of a decoupling collision zone. In particular, it succeeds without a seed facilitating initial separation of layers. External shortening of a continent - ocean - continent assembly, such as to initiate oceanic subduction, is lifted before the whole oceanic part is consumed, leaving slab pull to govern further convergence. Once buoyant continental crust enters, the collision zone locks, and convergence diminishes. Under favourable conditions, delamination then initiates close to the edge of the mantle wedge and at deep crustal levels. While it initially separates upper crust from lower crust according to the weakness minimum in the lithospheric strength profile, the lower crust is eventually also delaminated from the subducting lithospheric mantle, owing to buoyancy differences. The level of delamination within the lithosphere seems thus first rheology-controlled, then density-controlled. Subduction-coupled delamination is contingent on retreat and decoupling of the subducting slab, which in turn is dependent on effective rheological weakening of the plate contact. Weakening is a function of shear-heating and hereby of

  17. Shape memory-based tunable resistivity of polymer composites

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Hongsheng, E-mail: hongshengluo@163.com [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Zhou, Xingdong; Ma, Yuanyuan [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Yi, Guobin, E-mail: ygb116@163.com [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Cheng, Xiaoling [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Zhu, Yong [Shanghai Hiend Polyurethane Inc., No. 389, Jinshan District, Shanghai (China); Zu, Xihong; Zhang, Nanjun; Huang, Binghao; Yu, Lifang [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China)

    2016-02-15

    Graphical abstract: Hybrid nanofillers of the CNTs and AgNPs were embedded into a shape memory polyurethane. The composites exhibited tunable conduction, which could be facially tailored by the compositions and the thermal–mechanical programming. - Highlights: • Electrically conductive polymer composites in bi-layer structure were fabricated. • The CNTs/AgNPs layer had influence on the mechanics and thermal transitions. • The conductivity could be facially tailored via a thermo-mechanical programming. • The AgNPs contents enlarged the gauge factor of the resistivity–strain curves. • Tunneling theory was suitable for simulating the strain-dependent behaviors. - Abstract: A conductive composite in bi-layer structure was fabricated by embedding hybrid nanofillers, namely carbon nanotubes (CNTs) and silver nanoparticles (AgNPs), into a shape memory polyurethane (SMPU). The CNT/AgNP-SMPU composites exhibited a novel tunable conductivity which could be facially tailored in wide range via the compositions or a specifically designed thermo-mechanical shape memory programming. The morphologies of the conductive fillers and the composites were investigated by scanning electron microscope (SEM). The mechanical and thermal measurements were performed by tensile tests and differential scanning calorimetry (DSC). By virtue of a specifically explored shape memory programming, the composites were stretched and fixed into different temporary states. The electrical resistivity (R{sub s}) varied accordingly, which was able to be stabilized along with the shape fixing. Theoretical prediction based upon the tunneling model was performed. The R{sub s}–strain curves of the composites with different compositions were well fitted. Furthermore, the relative resistivity and the Gauge factor along with the elongation were calculated. The influence of the compositions on the strain-dependent R{sub s} was disclosed. The findings provided a new avenue to tailor the conductivity

  18. Detection and characterisation of delamination in PV modules by active infrared thermography

    Science.gov (United States)

    Sinha, A.; Sastry, O. S.; Gupta, R.

    2016-01-01

    The paper presents a fast and efficient method for the detection and characterisation of delamination in photovoltaic (PV) modules by using active infrared thermography approach. A discrete part of PV module was irradiated by step heating and its thermal image sequence was used to detect and analyse delamination. Different types of heating source for thermal excitation for this application have been studied. An electro-thermal model was developed to simulate the active thermography approach for the characterisation of delamination in PV module by equivalent resistance-capacitance (RC) network using a circuit simulator. This simulation approach was used to estimate the extent of delamination in the module and to determine the optimum parameters for the characterisation of delamination. Different applications based on front and backsides of heating the module were also proposed in this paper. The proposed method has the potential to be employed for the quality check of PV modules during inline production as well as for the predictive maintenance of outdoor PV plants.

  19. The concept of fatigue fracture toughness in fatigue delamination growth behavior

    NARCIS (Netherlands)

    Yao, L.; Alderliesten, R.C.; Benedictus, R.

    2015-01-01

    This paper provides a study on mode I fatigue delamination growth in composite laminates using energy principles. Experimental data has been obtained from fatigue tests conducted on Double Cantilever Beam (DCB) specimens at various stress ratios. A concept of fatigue fracture toughness is proposed t

  20. Thermal Oxidation Resistance of Rare Earth-Containing Composite Elastomer

    Institute of Scientific and Technical Information of China (English)

    邱关明; 张明; 周兰香; 中北里志; 井上真一; 冈本弘

    2001-01-01

    The rare earth-containing composite elastomer was obtained by the reaction of vinyl pyridine-SBR (PSBR) latex with rare earth alkoxides, and its thermal oxidation resistance was studied. After aging test, it is found that its retention rate of mechanical properties is far higher than that of the control sample. The results of thermogravimetric analysis show that its thermal-decomposing temperature rises largely. The analysis of oxidation mechanisms indicates that the main reasons for thermal oxidation resistance are that rare earth elements are of the utility to discontinue autoxidation chain reaction and that the formed complex structure has steric hindrance effect on oxidation.

  1. The corrosion resistance of zinc-nickel composite coatings

    OpenAIRE

    Panek, J; Bierska-Piech; M. Karolus

    2011-01-01

    Purpose: The aim of this work was to estimate the corrosion resistance of composite Zn+Ni and (Ni-Zn+Ni)/Zn coatings by salt spray test, electrochemical methods and grazing incidence X-ray diffraction (GIXD) method.Design/methodology/approach: The corrosion resistance properties of zinc-nickel coatings in 5% NaCl solution were investigated by salt spray test in 5% NaCl solution and electrochemical methods. Using Stern method the corrosion potential - Ecorr, corrosion current density - icorr,...

  2. Floating Node Method and Virtual Crack Closure Technique for Modeling Matrix Cracking-Delamination Interaction

    Science.gov (United States)

    DeCarvalho, N. V.; Chen, B. Y.; Pinho, S. T.; Baiz, P. M.; Ratcliffe, J. G.; Tay, T. E.

    2013-01-01

    A novel approach is proposed for high-fidelity modeling of progressive damage and failure in composite materials that combines the Floating Node Method (FNM) and the Virtual Crack Closure Technique (VCCT) to represent multiple interacting failure mechanisms in a mesh-independent fashion. In this study, the approach is applied to the modeling of delamination migration in cross-ply tape laminates. Delamination, matrix cracking, and migration are all modeled using fracture mechanics based failure and migration criteria. The methodology proposed shows very good qualitative and quantitative agreement with experiments.

  3. Floating Node Method and Virtual Crack Closure Technique for Modeling Matrix Cracking-Delamination Migration

    Science.gov (United States)

    DeCarvalho, Nelson V.; Chen, B. Y.; Pinho, Silvestre T.; Baiz, P. M.; Ratcliffe, James G.; Tay, T. E.

    2013-01-01

    A novel approach is proposed for high-fidelity modeling of progressive damage and failure in composite materials that combines the Floating Node Method (FNM) and the Virtual Crack Closure Technique (VCCT) to represent multiple interacting failure mechanisms in a mesh-independent fashion. In this study, the approach is applied to the modeling of delamination migration in cross-ply tape laminates. Delamination, matrix cracking, and migration are all modeled using fracture mechanics based failure and migration criteria. The methodology proposed shows very good qualitative and quantitative agreement with experiments.

  4. Buckling and Delamination of Ti/Cu/Si Thin Film During Annealing

    Science.gov (United States)

    Lin, Qijing; Yang, Shuming; Jing, Weixuan; Li, Changsheng; Wang, Chenying; Jiang, Zhuangde; Jiang, Kely

    2014-09-01

    In this paper, the formation of buckling and delamination of sandwiched stacking of Ti/Cu/Si thin film are investigated. The crystallization structures, the composition of the Cu/Ti thin films, and the surface morphology are measured during annealing. The results show that the solid-phase reaction between Cu and Ti occurs at the interface. Buckling is initiated in the thin film annealed at 600°C. The volume expansion promotes the buckling and further produces microcracks. With increasing volume expansion, there are cavities formed in the middle layer when the annealing temperature is up to 700°C. Finally, thin film is delaminated from the substrate.

  5. Impact Resistance of EBC Coated SiC/SiC Composites

    Science.gov (United States)

    Fox, Dennis S.; Bhatt, Ramakrishna T.; Choi, Sung R.; Cosgriff, Laura M.; Fox, Dennis s.; Lee, Kang N.

    2008-01-01

    Impact performance of 2-D woven SiC/SiC composites coated with 225 and 525 m thick environmental barrier coating (EBC) was investigated. The composites were fabricated by melt infiltration and the EBC was deposited by plasma spray. Impact tests were conducted at room temperature and at 1316 C in air using 1.59-mm diameter steel-balls at projectile velocities ranging from 110 to 375 m/s. Both microscopy and nondestructive evaluation (NDE) methods were used to determine the extent of damage in the substrate and coating with increasing projectile velocity. The impacted specimens were tensile tested at room temperature to determine their residual mechanical properties. At projectile velocities less than 125 m/s, no detectable damage was noticed in the MI SiC/SiC composites coated with 525 m EBC. With increase in projectile velocity beyond this value, spallation of EBC layers, delamination of fiber plies, and fiber fracture were detected. At a fixed projectile velocity, the composites coated with 525 m EBC showed less damage than the composite coated with 225 m EBC. Both types of EBC coated composites retained a large fraction of the baseline properties of as-fabricated composites and exhibited non-brittle failure after impact testing at projectile velocities up to 375 m/s. Exposure of impact tested specimens in a moisture environment at 1316 C for 500 hr indicated that the through-the-thickness cracks in the EBC coating and delamination cracks in the substrate generated after impact testing acted as conduits for internal oxidation.

  6. On a multiscale strategy and its optimization for the simulation of combined delamination and buckling

    CERN Document Server

    Saavedra, Karin; Gosselet, Pierre; 10.1002/nme.4305

    2012-01-01

    This paper investigates a computational strategy for studying the interactions between multiple through-the-width delaminations and global or local buckling in composite laminates taking into account possible contact between the delaminated surfaces. In order to achieve an accurate prediction of the quasi-static response, a very refined discretization of the structure is required, leading to the resolution of very large and highly nonlinear numerical problems. In this paper, a nonlinear finite element formulation along with a parallel iterative scheme based on a multiscale domain decomposition are used for the computation of 3D mesoscale models. Previous works by the authors already dealt with the simulation of multiscale delamination assuming small perturbations. This paper presents the formulation used to include geometric nonlinearities into this existing multiscale framework and discusses the adaptations that need to be made to the iterative process in order to ensure the rapid convergence and the scalabi...

  7. Delamination of Compressed thin Layers at Corners

    DEFF Research Database (Denmark)

    Clausen, Johan; Jensen, Henrik Myhre; Sørensen, Kim Dalsten

    2008-01-01

    An analysis of delamination for a thin elastic film, attached to a substrate with a corner, is carried out. The film is in compression and the analysis is performed by combining results from fracture mechanics and the theory of thin shells. The results show a very strong dependency of the angle...

  8. Failure and Delamination in Microelectronic Packages

    NARCIS (Netherlands)

    Sadeghinia, M.

    2013-01-01

    Thin layers of dissimilar materials are used in most microelectronic components in order to achieve special functional requirements. Generally, the interface between two adjacent materials forms a weak link, not only because of the relatively low delamination strength, but also because of the existi

  9. Effect of tool geometry and cutting parameters on delamination and thrust forces in drilling CFRP/Al-Li

    Science.gov (United States)

    El Bouami, Souhail; Habak, Malek; Franz, Gérald; Velasco, Raphaël; Vantomme, Pascal

    2016-10-01

    Composite materials are increasingly used for structural parts in the aeronautic industries. Carbon Fiber-Reinforced Plastics (CFRP) are often used in combination with metallic materials, mostly aluminium alloys. This raises new problems in aircraft assembly. Delamination is one of these problems. In this study, CFRP/Al-Li stacks is used as experimental material for investigation effect of interaction of cutting parameters (cutting speed and feed rate) and tool geometry on delamination and thrust forces in drilling operation. A plan of experiments, based on Taguchi design method, was employed to investigate the influence of tool geometry and in particular the point angle and cutting parameters on delamination and axial effort. The experimental results demonstrate that the feed rate is the major parameter and the importance of tool point angle in delamination and thrust forces in the stacks were shown.

  10. Fissure sealant materials: Wear resistance of flowable composite resins.

    Science.gov (United States)

    Asefi, Sohrab; Eskandarion, Solmaz; Hamidiaval, Shadi

    2016-01-01

    Background. Wear resistance of pit and fissure sealant materials can influence their retention. Wear characteristics of sealant materials may determine scheduling of check-up visits. The aim of this study was to compare wear resistance of two flowable composite resins with that of posterior composite resin materials. Methods. Thirty-five disk-shaped specimens were prepared in 5 groups, including two flowable composite resins (Estelite Flow Quick and Estelite Flow Quick High Flow), Filtek P90 and Filtek P60 and Tetric N-Ceram. The disk-shaped samples were prepared in 25-mm diameter by packing them into a two-piece aluminum mold and then light-cured. All the specimens were polished for 1minute using 600-grit sand paper. The samples were stored in distilled water at room temperature for 1 week and then worn by two-body abrasion test using "pin-on-disk" method (with distilled water under a 15-Nload at 0.05 m/s, for a distance of 100 meter with Steatite ceramic balls antagonists). A Profilometer was used for evaluating the surface wear. Data were analyzed with the one-way ANOVA. Results. Estelite Flow Quick exhibited 2708.9 ± 578.1 μm(2) and Estelite Flow Quick High Flow exhibited 3206 ± 2445.1 μm(2)of wear but there were no significant differences between the groups. They demonstrated similar wear properties. Conclusion. Estelite flowable composite resins have wear resistance similar to nano- and micro-filled and micro-hybrid composite resins. Therefore, they can be recommended as pit and fissure sealant materials in the posterior region with appropriate mechanical characteristics.

  11. Fissure sealant materials: Wear resistance of flowable composite resins

    Directory of Open Access Journals (Sweden)

    Sohrab Asefi

    2016-08-01

    Full Text Available Background. Wear resistance of pit and fissure sealant materials can influence their retention. Wear characteristics of sealant materials may determine scheduling of check-up visits. The aim of this study was to compare wear resistance of two flowable composite resins with that of posterior composite resin materials. Methods. Thirty-five disk-shaped specimens were prepared in 5 groups, including two flowable composite resins (Estelite Flow Quick and Estelite Flow Quick High Flow, Filtek P90 and Filtek P60 and Tetric N-Ceram. The disk-shaped samples were prepared in 25-mm diameter by packing them into a two-piece aluminum mold and then light-cured. All the specimens were polished for 1minute using 600-grit sand paper. The samples were stored in distilled water at room temperature for 1 week and then worn by two-body abrasion test using "pin-on-disk" method (with distilled water under a 15-Nload at 0.05 m/s, for a distance of 100 meter with Steatite ceramic balls antagonists. A Profilometer was used for evaluating the surface wear. Data were analyzed with the one-way ANOVA. Results. Estelite Flow Quick exhibited 2708.9 ± 578.1 μm2 and Estelite Flow Quick High Flow exhibited 3206 ± 2445.1 μm2of wear but there were no significant differences between the groups. They demonstrated similar wear properties. Conclusion. Estelite flowable composite resins have wear resistance similar to nano- and micro-filled and micro-hybrid composite resins. Therefore, they can be recommended as pit and fissure sealant materials in the posterior region with appropriate mechanical characteristics.

  12. Fissure sealant materials: Wear resistance of flowable composite resins

    Science.gov (United States)

    Asefi, Sohrab; Eskandarion, Solmaz; Hamidiaval, Shadi

    2016-01-01

    Background. Wear resistance of pit and fissure sealant materials can influence their retention. Wear characteristics of sealant materials may determine scheduling of check-up visits. The aim of this study was to compare wear resistance of two flowable composite resins with that of posterior composite resin materials. Methods. Thirty-five disk-shaped specimens were prepared in 5 groups, including two flowable composite resins (Estelite Flow Quick and Estelite Flow Quick High Flow), Filtek P90 and Filtek P60 and Tetric N-Ceram. The disk-shaped samples were prepared in 25-mm diameter by packing them into a two-piece aluminum mold and then light-cured. All the specimens were polished for 1minute using 600-grit sand paper. The samples were stored in distilled water at room temperature for 1 week and then worn by two-body abrasion test using "pin-on-disk" method (with distilled water under a 15-Nload at 0.05 m/s, for a distance of 100 meter with Steatite ceramic balls antagonists). A Profilometer was used for evaluating the surface wear. Data were analyzed with the one-way ANOVA. Results. Estelite Flow Quick exhibited 2708.9 ± 578.1 μm2 and Estelite Flow Quick High Flow exhibited 3206 ± 2445.1 μm2of wear but there were no significant differences between the groups. They demonstrated similar wear properties. Conclusion. Estelite flowable composite resins have wear resistance similar to nano- and micro-filled and micro-hybrid composite resins. Therefore, they can be recommended as pit and fissure sealant materials in the posterior region with appropriate mechanical characteristics. PMID:27651887

  13. Wear Resistance of Friction Pair of Metal Composite/Copper under Electric Current

    Science.gov (United States)

    Aleutdinova, M. I.; Fadin, V. V.; Rubtsov, V. Ye; Aleutdinov, K. A.

    2016-11-01

    Sliding of metal composites against copper counterbody under severe conditions (i.e. at the contact current density higher 50 A/cm2 and at high roughness of counterbody) is carried out. It is shown that the composite of composition of Cu-30% of graphite shows low wear resistance in these conditions. Higher wear resistance is inherent in the composites containing lead and bearing steel. Impregnation of these composites by industrial oil hasn't led to noticeable increase in wear resistance.

  14. Effect of Location of Delamination on Free Vibration of Cross-Ply Conical Shells

    Directory of Open Access Journals (Sweden)

    Sudip Dey

    2012-01-01

    Full Text Available Location of delamination is a triggering parameter for structural instability of laminated composites. In this paper, a finite element method is employed to determine the effects of location of delamination on free vibration characteristics of graphite-epoxy cross-ply composite pre-twisted shallow conical shells. The generalized dynamic equilibrium equation is derived from Lagrange's equation of motion neglecting Coriolis effect for moderate rotational speeds. The formulation is exercised by using an eight noded isoparametric plate bending element based on Mindlin's theory. Multi-point constraint algorithm is utilized to ensure the compatibility of deformation and equilibrium of resultant forces and moments at the delamination crack front. The standard eigen value problem is solved by applying the QR iteration algorithm. Finite element codes are developed to obtain the numerical results concerning the effects of location of delamination, twist angle and rotational speed on the natural frequencies of cross-ply composite shallow conical shells. The mode shapes are also depicted for a typical laminate configuration. Numerical results obtained from parametric studies of both symmetric and anti-symmetric cross-ply laminates are the first known non-dimensional natural frequencies for the type of analyses carried out here.

  15. Influence of substrate topography on cathodic delamination of anticorrosive coatings

    DEFF Research Database (Denmark)

    Sørensen, Per Aggerholm; Kiil, Søren; Dam-Johansen, Kim

    2009-01-01

    The cathodic delamination of a commercial magnesium silicate and titanium dioxide pigmented epoxy coating on abrasive cleaned cold rolled steel has been investigated. The rate of delamination was found to depend on interfacial transport from the artificial defect to the delamination front...... and thereby the substrate topography, whereas the coating thickness had little influence. The presence of a significant potential gradient between the anode and the cathode and the dependency of the delamination rate on the tortuosity of the steel surface suggests that cathodic delamination is controlled...... by migration of cations from the defect to the delamination front. This means that abrasive blasting, to some extent, can be applied to control and minimize the observed rate of cathodic delamination. The lifetime of the species causing disbondment suggested that sodium hydroxide or potassium hydroxide...

  16. Effect of oxidation on delamination of ultrahigh-molecular-weight polyethylene tibial components.

    Science.gov (United States)

    Bell, C J; Walker, P S; Abeysundera, M R; Simmons, J M; King, P M; Blunn, G W

    1998-04-01

    Whether oxidation of ultrahigh-molecular-weight polyethylene (UHMWPE) causes delamination of the plastic in total knee arthroplasties (TKAs) was investigated. Examination of retrieved TKAs has shown that oxidation of UHMWPE can be caused by postirradiation damage leading to a subsurface band or, to a lesser extent, by mechanical forces during use leading to surface oxidation. Delamination cracks propagated through the subsurface oxidized band. In wear tests, delamination occurred in artificially aged UHMWPE where only subsurface oxidized bands had formed. Increased surface wear predominated where oxidation was associated with the surface of the plastic. Similarly, in tensile and fatigue tests of oxidized UHMWPE, there was a significant reduction in the ultimate tensile strength and in the fatigue resistance of specimens that had developed a subsurface band. Oxidation increased fatigue crack growth rate. It was observed that UHMWPE from different manufacturers varied in its resistance to oxidation. This study demonstrates that the effect of oxidation, which results in the development of a subsurface white band, combined with high subsurface shear forces observed in TKAs, is to enhance delamination wear.

  17. Monitoring Damage Accumulation in Ceramic Matrix Composites Using Electrical Resistivity

    Science.gov (United States)

    Smith, Craig E.; Morscher, Gregory N.; Xia, Zhenhai H.

    2008-01-01

    The electric resistance of woven SiC fiber reinforced SiC matrix composites were measured under tensile loading conditions. The results show that the electrical resistance is closely related to damage and that real-time information about the damage state can be obtained through monitoring of the resistance. Such self-sensing capability provides the possibility of on-board/in-situ damage detection and accurate life prediction for high-temperature ceramic matrix composites. Woven silicon carbide fiber-reinforced silicon carbide (SiC/SiC) ceramic matrix composites (CMC) possess unique properties such as high thermal conductivity, excellent creep resistance, improved toughness, and good environmental stability (oxidation resistance), making them particularly suitable for hot structure applications. In specific, CMCs could be applied to hot section components of gas turbines [1], aerojet engines [2], thermal protection systems [3], and hot control surfaces [4]. The benefits of implementing these materials include reduced cooling air requirements, lower weight, simpler component design, longer service life, and higher thrust [5]. It has been identified in NASA High Speed Research (HSR) program that the SiC/SiC CMC has the most promise for high temperature, high oxidation applications [6]. One of the critical issues in the successful application of CMCs is on-board or insitu assessment of the damage state and an accurate prediction of the remaining service life of a particular component. This is of great concern, since most CMC components envisioned for aerospace applications will be exposed to harsh environments and play a key role in the vehicle s safety. On-line health monitoring can enable prediction of remaining life; thus resulting in improved safety and reliability of structural components. Monitoring can also allow for appropriate corrections to be made in real time, therefore leading to the prevention of catastrophic failures. Most conventional nondestructive

  18. Comparison of Wear Resistance Between Innovative Composites and Nano- and Microfilled Composite Resins

    Directory of Open Access Journals (Sweden)

    Asefi

    2016-02-01

    Full Text Available Background One of the most common causes of failure in class 2 posterior composite restorations is occlusal and proximal wear. Estelite composites used supra-nano monodispersing spherical fillers and a new photoinitiator, and the manufacturer claimed that the wear of these composites is less than 1 mm3 volumetric wear. Objectives Compare the wear resistance of new Estelite composites with that of other composites generations. Materials and Methods Thirty-five specimens were evaluated in five groups: three kinds of Estelite composites (Estelite Sigma Quick, Estelite Flow Quick, and Estelite Flow Quick High Flow, Filtek Z350, and Filtek Z250. All specimens were prepared in 25 mm disks and cured with laboratory light for 120 seconds (60 s for each side. Then, they were polished by 600 grit sand paper and stored for one week in distilled water at room temperature. We used a two-body abrasion test and the pin-on-disk method with distilled water as medium. All specimens were worn under 15 N load, 0.05 m/seconds speed, 100 m distance, and steatite ceramic balls antagonists. After wearing, we measured wear volume by calculating the wear track cross-section area with a profilometer and analyzed the data with the one-way analysis of variance (ANOVA test. Results The wear amounts of the composites are as follows in order: Estelite sigma quick (1886.9 ± 518.5 μm2, Estelite flow quick (2708.9 ± 578.1 μm2, Estelite high flow (3206 ± 2445.1 μm2, Filtek Z350 (3840 ± 1963.4 μm2, and Filtek Z250 (4667.2 ± 2351.1 μm2. No statistical difference was found among the groups (P value > 0.05. Conclusions Estelite sigma quick composite had wear resistance similar to that of nano- and microfilled composites. Estelite flowable composites demonstrated similar wear resistance to that of a posterior composite.

  19. Challenges in Modelling of Lightning-Induced Delamination; Effect of Temperature-Dependent Interfacial Properties

    Science.gov (United States)

    Naghipour, P.; Pineda, E. J.; Arnold, S.

    2014-01-01

    Lightning is a major cause of damage in laminated composite aerospace structures during flight. Due to the dielectric nature of Carbon fiber reinforced polymers (CFRPs), the high energy induced by lightning strike transforms into extreme, localized surface temperature accompanied with a high-pressure shockwave resulting in extensive damage. It is crucial to develop a numerical tool capable of predicting the damage induced from a lightning strike to supplement extremely expensive lightning experiments. Delamination is one of the most significant failure modes resulting from a lightning strike. It can be extended well beyond the visible damage zone, and requires sophisticated techniques and equipment to detect. A popular technique used to model delamination is the cohesive zone approach. Since the loading induced from a lightning strike event is assumed to consist of extreme localized heating, the cohesive zone formulation should additionally account for temperature effects. However, the sensitivity to this dependency remains unknown. Therefore, the major focus point of this work is to investigate the importance of this dependency via defining various temperature dependency profiles for the cohesive zone properties, and analyzing the corresponding delamination area. Thus, a detailed numerical model consisting of multidirectional composite plies with temperature-dependent cohesive elements in between is subjected to lightning (excessive amount of heat and pressure) and delamination/damage expansion is studied under specified conditions.

  20. Metal-nanotube composites as radiation resistant materials

    Energy Technology Data Exchange (ETDEWEB)

    González, Rafael I.; Valencia, Felipe; Mella, José; Kiwi, Miguel, E-mail: m.kiwi.t@gmail.com [Departamento de Física, Facultad de Ciencias, CEDENNA, Universidad de Chile, Casilla 653, Santiago 7800024 (Chile); Duin, Adri C. T. van [Department of Mechanical and Nuclear Engineering, The Pennsylvania State University, University Park, Pennsylvania 16802 (United States); So, Kang Pyo; Li, Ju [Department of Nuclear Science and Engineering and Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Bringa, Eduardo M. [CONICET and Facultad de Ciencias Exactas y Naturales, Universidad Nacional de Cuyo, Mendoza 5500 (Argentina)

    2016-07-18

    The improvement of radiation resistance in nanocomposite materials is investigated by means of classical reactive molecular dynamics simulations. In particular, we study the influence of carbon nanotubes (CNTs) in an Ni matrix on the trapping and possible outgassing of He. When CNTs are defect-free, He atoms diffuse alongside CNT walls and, although there is He accumulation at the metal-CNT interface, no He trespassing of the CNT wall is observed, which is consistent with the lack of permeability of a perfect graphene sheet. However, when vacancies are introduced to mimic radiation-induced defects, He atoms penetrate CNTs, which play the role of nano-chimneys, allowing He atoms to escape the damaged zone and reduce bubble formation in the matrix. Consequently, composites made of CNTs inside metals are likely to display improved radiation resistance, particularly when radiation damage is related to swelling and He-induced embrittlement.

  1. Middle Archean continent formation by crustal delamination

    Science.gov (United States)

    Zegers, Tanja E.; van Keken, Peter E.

    2001-12-01

    The processes that created the first large cratonic areas such as the Pilbara and the Kaapvaal remain poorly understood. Models based on the uniformitarian extrapolation of present-day arc volcanic processes to a hotter early Earth have not adequately explained the observations in these terranes. Here we propose an alternative mechanism for the formation of the earliest continental crust. The formation of continental crust may be achieved by delamination of the lower eclogitic part of an oceanic plateau like protocrust. Such delamination results in uplift, extension, and the production of tonalite, trondhjemite, and granodiorite (TTG) suites as recorded in Middle Archean cratons. The available geologic and geophysical observations in combination with model calculations permit this scenario as an alternative to subduction-based hypotheses.

  2. Fracture resistance of teeth restored with packable and hybrid composites

    Directory of Open Access Journals (Sweden)

    Ghavam M

    2006-06-01

    Full Text Available Background and Aim: With recent introduction of packable composites, it is claimed that they apply less stress on tooth structure because of reduced polymerization shrinkage, and similarity of coefficient of thermal expansion to tooth structure. However, the high viscosity may in turn cause less adaptation, so it is not clearly known whether these materials strengthen tooth structure or not. The aim of this study was to evaluate fracture resistance of maxillary premolars, receiving hybrid or packable composite restorations with different methods of application and curing. Materials and Methods: In this experimental study, seventy five intact premolars were randomly assigned to five groups of 15 teeth each. One group was maintained intact as the control group. Similar MOD cavities were prepared in the other teeth. The teeth in group two were restored with Spectrum in incremental layers and light cured with 500 mw/cm2 intensity. The third group were filled with Surefil and cured with light intensity of 500 mw/cm2. The groups four and five were restored with Surefil in bulk technique with two different modes: 500 mw/cm2 intensity and a ramp mode (100-900 mw/cm2 respectively. After thermocycling, force to fracture was assessed and degree of conversion (DC at the bottom of cavities was evaluated for different modes and methods. The curing and placement methods in groups tested for DC (A to D were the same as fracture resistance groups (2 to 5. Data were analyzed using one way ANOVA and Tukey HSD tests with p<0.05 as the limit of significance. Results: All the restored groups showed significantly less fracture resistance than the control group, but had no significant difference among themselves. DC of Spectrum was higher than Surefil. Bulk method with 500 mw/cm2 light intensity, significantly decreased DC. DC in bulk method with high light intensity was not significantly different from incremental method with 500 mw/cm2 light intensity. Conclusion

  3. Design of engineered cementitious composites for ductile seismic resistant elements

    Science.gov (United States)

    Kanda, Tetsushi

    This dissertation focuses on designing Engineered Cementitious Composite (ECC) to achieve high performance seismic resistant elements. To attain this goal, three major tasks have been accomplished. Task 1 aims at achieving new ECCs involving low cost fiber, which often involve fiber rupture in crack bridging, thus named as "Fiber Rupture Type ECC". Achieving the new ECC requires a new practical and comprehensive composite design theory. For this theory, single fiber behavior was first investigated. Specifically, fiber rupture in composite and chemical bond in fiber/matrix interface were experimentally examined and mathematically modeled. Then this model for single fiber behavior was implemented into a proposed bridging law, a theoretical model for relationship between fiber bridging stress of composite and Crack Opening Displacement (COD). This new bridging law was finally employed to establish a new composite design theory. Task 2 was initiated to facilitate structural interpretation of ECC's material behavior investigated in Task 1. For this purpose, uniaxial tensile behavior, one of the most important ECC's properties, was theoretically characterized with stress-strain relation from micromechanics view point. As a result, a theory is proposed to express ECC's tensile stress-strain relation in terms of micromechanics parameters of composites, such as bond strengths. Task 3 primarily demonstrates an integrated design scheme for ductile seismic elements that covers from micromechanics in single fiber level to structural design tool, such as with non-linear FEM analysis. The significance of this design scheme is that the influences of ECC's microstructure on element's structural performance is quantitatively captured. This means that a powerful tool is obtained for tailoring constitutive micromechanics parameters in order to maximize structural performance of elements. While the tool is still preliminary, completing this tool in future studies will enable one to

  4. Influence of Material Distribution on Impact Resistance of Hybrid Composites

    Science.gov (United States)

    Abatan, Ayu; Hu, Hurang

    1998-01-01

    Impact events occur in a wide variety of circumstances. A typical example is a bullet impacting a target made of composite material. These impact events produce time-varying loads on a structure that can result in damage. As a first step to understanding the damage resistance issue in composite laminates, an accurate prediction of the transient response during an impact event is necessary. The analysis of dynamic loadings on laminated composite plates has undergone considerable development recently. Rayleigh-Ritz energy method was used to determine the impact response of laminated plates. The impact response of composite plates using shear deformation plate theory was analyzed. In recent work a closed-form solution was obtained for a rectangular plate with four edges simply supported subjected to a center impact load using classical plate theory. The problem was further investigated and the analysis results compared of both classical plate theory and shear deformation theory, and found that classical plate theory predicts very accurate results for the range of small deformations considered. In this study, the influence of cross sectional material distribution on the comparative impact responses of hybrid metal laminates subjected to low and medium velocity impacts is investigated. A simple linear model to evaluate the magnitude of the impact load is proposed first, and it establishes a relation between the impact velocity and the impact force. Then a closed-form solution for impact problem is presented. The results were compared with the finite element analysis results. For an 11 layer-hybrid laminate, the impact response as a function of material distribution in cross-section is presented. With equal areal weight, the effect of the number of laminate layers on the impact resistance is also investigated. Finally, the significance of the presented results is discussed.

  5. Development of oxidation/corrosion-resistant composite materials and interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Stinton, D.P.; Besmann, T.M.; Shanmugham, S. [and others

    1995-06-01

    Continuous fiber ceramic composites (CFCCs) are being developed for high temperature structural applications, many of which are in oxidative environments. Such composites are attractive since they are light-weight and possess the desired mechanical properties at elevated temperature and in aggressive environments. The most significant advantage is their toughness and their non-catastrophic failure behavior. The mechanical properties of CFCCs have been characteristically linked with the nature of the interfacial bond between the fibers and the matrix. Weakly bonded fiber-matrix intefaces allow an impinging matrix crack to be deflected such that the fracture process occurs through several stages: Crack deflection, debonding at the interface, fiber slip and pull-out, and ultimately fiber failure. Such a composite will fail in a graceful manner and exhibit substantial fracture toughness. Currently, carbon interface coatings are used to appropriately tailor interface properties, however their poor oxidation resistance has required a search of an appropriate replacement. Generally, metal oxides are inherently stable to oxidation and possess thermal expansion coefficients relatively close to those of Nicalon and SiC. However, the metal oxides must also be chemically compatible with the fiber and matrix. If the fiber/interface/matrix system is chemically compatible, then the interfacial bonding stress is influenced by the thermal residual stresses that are generated as the composite is cooled from processing to room temperature. In the current work, thermomechanical computational results were obtained from a finite element model (FEM) for calculating the thermal residual stresses. This was followed by experimental evaluation of Nicalon/SiC composites with carbon, alumina, and mullite interfacial coatings.

  6. Development of a Benchmark Example for Delamination Fatigue Growth Prediction

    Science.gov (United States)

    Krueger, Ronald

    2010-01-01

    The development of a benchmark example for cyclic delamination growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of a Double Cantilever Beam (DCB) specimen, which is independent of the analysis software used and allows the assessment of the delamination growth prediction capabilities in commercial finite element codes. First, the benchmark result was created for the specimen. Second, starting from an initially straight front, the delamination was allowed to grow under cyclic loading in a finite element model of a commercial code. The number of cycles to delamination onset and the number of cycles during stable delamination growth for each growth increment were obtained from the analysis. In general, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. Overall, the results are encouraging but further assessment for mixed-mode delamination is required.

  7. On a multiscale strategy and its optimization for the simulation of combined delamination and buckling

    Science.gov (United States)

    Saavedra, K.; Allix, O.; Gosselet, P.

    2012-08-01

    This paper investigates a computational strategy for studying the interactions between multiple through-the-width delaminations and global or local buckling in composite laminates taking into account possible contact between the delaminated surfaces. In order to achieve an accurate prediction of the quasi-static response, a very refined discretization of the structure is required, leading to the resolution of very large and highly nonlinear numerical problems. In this paper, a nonlinear finite element formulation along with a parallel iterative scheme based on a multiscale domain decomposition are used for the computation of 3D mesoscale models. Previous works by the authors already dealt with the simulation of multiscale delamination assuming small perturbations. This paper presents the formulation used to include geometric nonlinearities into this existing multiscale framework and discusses the adaptations that need to be made to the iterative process in order to ensure the rapid convergence and the scalability of the method in the presence of buckling and delamination. These various adaptations are illustrated by simulations involving large numbers of DOFs.

  8. The arc delaminate: a geochemical reservoir twice the size of the continental crust

    Science.gov (United States)

    Jagoutz, O.; Schmidt, M. W.

    2012-12-01

    Most primitive melts in arcs are basaltic in composition but the continental crust or arc average is andesitic. To evolve from a primitive basalt to an andesitic composition, cumulates have to be fractionated and, if gravitationally unstable, can be delaminated. Such lower crustal cumulates are exposed in the Kohistan arc (N Pakistan) in a 10 km section through dunites, wehrlites, websterites, cpx-bearing garnetites and hornblendites, and garnet gabbros. We have compiled primitive melts for nine island arcs from the literature and fitted these with the bulk Kohistan arc [1] or average bulk continental crust [2] and the Kohistan cumulates. By average, ~15 wt% wehrlite + ~20% garnet hornblendite + ~35% garnet gabbro complement ~30% arc or continental crust and explain very well (r2~2) the evolution from a tholeiitic/calc-alkaline primitive high-Mg basalt to the continental crust. The bulk delaminate has 44-48 wt% SiO2, total alkalis of 1.1-1.4 wt% and an XMg of 0.67-0.69. Mass fractions derived from major elements were employed to compare trace elements: cumulates+crust deviate on average only by 25-30% from primitive melts, with the biggest deviations on the subduction-added traces. Relative to the continental or arc crust, the delaminate mass results to 1.8-2.5 times that of the continental crust. The delaminates have rho=3.2-3.5 g/cm3 and VP=7.9-8.2. At the base of the crust, they are thus difficult to distinguish seismically. Once reaching a critical thickness, they may sink into the deeper mantle where they form a geochemical reservoir twice the size of the continental crust. With respect to primitive mantle, the delaminate is enriched in Ba, K, Sr, and P and REE with LREEdelaminate reservoir would develop highly unradiogenic Pb over time and would counterbalance the radiogenic MORB and OIB reservoirs. Delamination of twice as much material as remains in the arc crust increases the flux of primitive melt in arcs threefold. This places the magma

  9. Hygroscopicity -resistant mechanism of an α -starch based composite binder for dry sand molds and cores

    Directory of Open Access Journals (Sweden)

    Xia ZHOU

    2005-05-01

    Full Text Available Hygroscopicity-resistance of an α-starch based composite binder for dry sand molds (cores has been studied experimentally and theoretically. Focus is placed on the relationship between the hardening structure and humidity-resistance of the composite binder. The results show that the α-starch composite binder has good humidity-resistance due to its special complex structure. SEM observations illustrate that the composite binder consists of reticular matrix and a ball- or lump-shaped reinforcement phase, and the specific property of the binding membrane with heterogeneous structure is affected by humidity to a small extent. Based on the analyses on the interplays of different ingredients in the binder at hardening, the structure model and hygroscopicity-resistant mechanisms of the hardening composite binder were further proposed. Moreover, the reasons for good humidity-resistance of the composite binder bonded sand are well explained by the humidity-resistant mechanisms.

  10. Subduction to Continental Delamination: Insights From Laboratory Experiments

    Science.gov (United States)

    Gogus, O. H.; Corbi, F.; Faccenna, C.; Pysklywec, R. N.

    2009-05-01

    The evolution of the lithosphere through subduction-collision and delamination and its surface/crustal response (topography/deformation) is investigated in this work. We present a series of lithosphere scale two dimensional (2-D) and three dimensional (3-D) laboratory experiments to better understand such processes. In these experiments, an idealized viscously deforming crust-mantle lithosphere-mantle system is configured with silicone putty (representing lithospheric mantle and upper crust) and glucose syrup (representing the upper mantle and lower crust). The initial focus was to investigate the physical development of delamination versus continental subduction without plate convergence. Experiments show that the delamination or continental subduction is strongly dependent on the density of the crust (both crust and mantle lithosphere subducts when crust has a higher density, instead of delamination), while in the investigated range, the viscosity of the weak layer does not have much influence on the process. In all the experiments, the topography is asymmetric with subsidence above the delaminating hinge due to the dynamic vertical pulling driven by the delaminating slab, and uplift above the delaminated region due to the buoyancy of asthenosphere. Our investigation on the oceanic subduction with a convergence rate of ~ 3cm/year plate velocity suggests that subduction -collision - delamination is well defined and at the end, the delaminating crust from the lithosphere is overthrusted on top of the overriding plate. Our results provide integrated insights on the Alpine-Himalayan type orogenies, in particular the neotectonic evolution of Eastern Anatolian plateau.

  11. Buckling-driven delamination of carbon nanotube forests

    Science.gov (United States)

    Pour Shahid Saeed Abadi, Parisa; Hutchens, Shelby B.; Greer, Julia R.; Cola, Baratunde A.; Graham, Samuel

    2013-06-01

    We report buckling-driven delamination of carbon nanotube (CNT) forests from their growth substrates when subjected to compression. Macroscale compression experiments reveal local delamination at the CNT forest-substrate interface. Results of microscale flat punch indentations indicate that enhanced CNT interlocking at the top surface of the forest accomplished by application of a metal coating causes delamination of the forest from the growth substrate, a phenomenon not observed in indentation of as-grown CNT forests. We postulate that the post-buckling tensile stresses that develop at the base of the CNT forests serve as the driving force for delamination.

  12. Sensing delamination in epoxy encapsulant systems with fiber Bragg gratings

    Science.gov (United States)

    Jones, Brad H.; Rohr, Garth D.; Kaczmarowski, Amy K.

    2016-05-01

    Fiber Bragg gratings (FBGs) are well-suited for embedded sensing of interfacial phenomena in materials systems, due to the sensitivity of their spectral response to locally non-uniform strain fields. Over the last 15 years, FBGs have been successfully employed to sense delamination at interfaces, with a clear emphasis on planar events induced by transverse cracks in fiber-reinforced plastic laminates. We have built upon this work by utilizing FBGs to detect circular delamination events at the interface between epoxy films and alumina substrates. Two different delamination processes are examined, based on stress relief induced by indentation of the epoxy film or by cooling to low temperature. We have characterized the spectral response pre- and post-delamination for both simple and chirped FBGs as a function of delamination size. We show that delamination is readily detected by the evolution of a non-uniform strain distribution along the fiber axis that persists after the stressing condition is removed. These residual strain distributions differ substantially between the delamination processes, with indentation and cooling producing predominantly tensile and compressive strain, respectively, that are well-captured by Gaussian profiles. More importantly, we observe a strong correlation between spectrally-derived measurements, such as spectral widths, and delamination size. Our results further highlight the unique capabilities of FBGs as diagnostic tools for sensing delamination in materials systems.

  13. Oxidation resistant coatings for ceramic matrix composite components

    Energy Technology Data Exchange (ETDEWEB)

    Vaubert, V.M.; Stinton, D.P. [Oak Ridge National Lab., TN (United States); Hirschfeld, D.A. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States). Dept. of Materials and Metallurgical Engineering

    1998-11-01

    Corrosion resistant Ca{sub 0.6}Mg{sub 0.4}Zr{sub 4}(PO{sub 4}){sub 6} (CMZP) and Ca{sub 0.5}Sr{sub 0.5}Zr{sub 4}(PO{sub 4}){sub 6} (CS-50) coatings for fiber-reinforced SiC-matrix composite heat exchanger tubes have been developed. Aqueous slurries of both oxides were prepared with high solids loading. One coating process consisted of dipping the samples in a slip. A tape casting process has also been created that produced relatively thin and dense coatings covering a large area. A processing technique was developed, utilizing a pre-sintering step, which produced coatings with minimal cracking.

  14. Review on Preservative Treatment and Decay Resistance of Wood-based Composites

    Institute of Scientific and Technical Information of China (English)

    LIU Zhi; CAO Jinzhen

    2006-01-01

    To extend the service life and explore the use of wood-based composites, it is quite necessary to improve the decay resistance of wood-based composites through preservative treatments. Researchers have studied the methods of preservative treatment and the decay resistance of treated wood-based composites. In this paper, the categories of wood-based composites are briefly summarized and the previous and present investigations on the preservative treatment and decay resistance of different categories of wood-based composites are introduced. Some problems are also put forward and suggestions are given for future studies.

  15. Effeet of Strain on the Electrical Resistance of Carbon Nanotube/Silicone Rubber Composites

    Institute of Scientific and Technical Information of China (English)

    ZENG You; LIU Huashi; CHEN Juan; GE Heyi

    2011-01-01

    Carbon nanotube (CNT) filled silicone rubber (SR) composites were synthesized by in situ polymerization.The effect of strain on the electrical resistance of the CNT/SR composites and the structure evolution of CNT networks during tensile deformation were investigated.The results showed that the CNT/SR composites had high sensitivity of resistance-strain response.In a wide strain range (0-125%),the change of resistivity could reach 107,which was closely associated with the evolution process of the conductive CNTnetwork structure.The volume expansion of the composites in the tensile process led to a gradual decrease in the volume fraction of CNTs with the strain increase.When CNT loading was lower than the percolation threshold,CNT network was in disconnected state with a rapid increase in electrical resistance of the composites.Furthermore,the CNT loading had remarkable effect on the sensitivity of resistance-strain response in the composites.

  16. Finite element based micro-mechanics modeling of textile composites

    Science.gov (United States)

    Glaessgen, E. H.; Griffin, O. H., Jr.

    1995-01-01

    Textile composites have the advantage over laminated composites of a significantly greater damage tolerance and resistance to delamination. Currently, a disadvantage of textile composites is the inability to examine the details of the internal response of these materials under load. Traditional approaches to the study fo textile based composite materials neglect many of the geometric details that affect the performance of the material. The present three dimensional analysis, based on the representative volume element (RVE) of a plain weave, allows prediction of the internal details of displacement, strain, stress, and failure quantities. Through this analysis, the effect of geometric and material parameters on the aforementioned quantities are studied.

  17. Failure Predictions of Out-of-Autoclave Sandwich Joints with Delaminations Under Flexure Loads

    Science.gov (United States)

    Nordendale, Nikolas A.; Goyal, Vinay K.; Lundgren, Eric C.; Patel, Dhruv N.; Farrokh, Babak; Jones, Justin; Fischetti, Grace; Segal, Kenneth N.

    2015-01-01

    An analysis and a test program was conducted to investigate the damage tolerance of composite sandwich joints. The joints contained a single circular delamination between the face-sheet and the doubler. The coupons were fabricated through out-of-autoclave (OOA) processes, a technology NASA is investigating for joining large composite sections. The four-point bend flexure test was used to induce compression loading into the side of the joint where the delamination was placed. The compression side was chosen since it tends to be one of the most critical loads in launch vehicles. Autoclave cure was used to manufacture the composite sandwich sections, while the doubler was co-bonded onto the sandwich face-sheet using an OOA process after sandwich panels were cured. A building block approach was adopted to characterize the mechanical properties of the joint material, including the fracture toughness between the doubler and face-sheet. Twelve four-point-bend samples were tested, six in the sandwich core ribbon orientation and six in sandwich core cross-ribbon direction. Analysis predicted failure initiation and propagation at the pre-delaminated location, consistent with experimental observations. A building block approach using fracture analyses methods predicted failure loads in close agreement with tests. This investigation demonstrated a small strength reduction due to a flaw of significant size compared to the width of the sample. Therefore, concerns of bonding an OOA material to an in-autoclave material was mitigated for the geometries, materials, and load configurations considered.

  18. Evaluation of Impact Damage Tolerance in Carbon Fabric/epoxy-matrix Composites by Electrical Resistance Measurement

    Institute of Scientific and Technical Information of China (English)

    LI Zhipeng; XIE Xiaolin; HONG Zhen; LU Chao; WANG Gaochao

    2012-01-01

    Impact damage tolerance is provided in intensity design on composites.The compression intensity of impacted composites requires more than 60% of its original intensity.The influence of impact on compressive intensity and electrical resistance of carbon fabric/epoxy-matrix composites was studied in this paper.The experimental results shows that impact can cause damage in composites,degenerate compressive intensity,and increase resistance.The electrical resistance change rate was used as an evaluation indicator of impact damage tolerance of composites.Impact damage,which results from the applying process of composites,can be identified in time by electrical resistance measurement.So,the safety performance of composites can also be improved.

  19. The Effect of Substrate Topography on Coating Cathodic Delamination

    DEFF Research Database (Denmark)

    Weinell, Claus E.; Sørensen, Per A.; Kiil, Søren

    2011-01-01

    This article describes the effect of steel substrate topography on coating cathodic delamination. The study showed that the surface preparation can be used to control and minimize the rate of cathodic delamination. The coating should have maximum wetting properties so that substrates with high...

  20. Buckling-driven Delamination in Layered Spherical Shells

    DEFF Research Database (Denmark)

    Sørensen, Kim Dalsten; Jensen, Henrik Myhre

    2008-01-01

    An analysis of buckling-driven delamination of a thin film on a spherical substrate has been carried out. The effects of the substrate having a double curvature compared to previous studies of delamination on cylindrical substrates turn out to be non-trivial: In addition to the effect of the shap...

  1. Gas permeation and temperature effects in laser-induced delamination

    NARCIS (Netherlands)

    Fedorov, Alexander; Vellinga, Willem-Pier; De Hosson, Jeff

    Laser-induced delamination (LID) is a technique aimed at measuring the work of adhesion of thin polymer coatings on metal substrates. A laser Pulse is used to create a blister that initiates delamination of the film under pressure. The stress fields in the blister wall and the work of adhesion of

  2. The effect of cerium-based conversion treatment on the cathodic delamination and corrosion protection performance of carbon steel-fusion-bonded epoxy coating systems

    Science.gov (United States)

    Ramezanzadeh, B.; Rostami, M.

    2017-01-01

    The effect of surface pre-treatment of pipe surface by green cerium compound and phosphoric acid solution on the fusion-bonded epoxy (FBE) coating performance was studied. The composition and surface morphology of the steel samples treated by acid and Ce solutions were characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), equipped with energy dispersive spectroscopy (EDS). Also, the surface free energy was evaluated on these samples through contact angle measurements. In addition, the effect of Ce and acid washing procedures on the adhesion properties and corrosion protection performance of the FBE was examined by pull-off, salt spray and electrochemical impedance spectroscopy (EIS) tests. Results showed that compared to acid washing, the chemical treatment by Ce solution noticeably increased the surface free energy of steel, improved the adhesion properties of FBE, decreased the cathodic delamination rate of FBE, and enhanced the coating corrosion resistance compared to the acid washed samples.

  3. Effect of composite/amalgam thickness on fracture resistance of maxillary premolar teeth, restored with combined amalgam-composite restorations

    Science.gov (United States)

    Firouzmandi, Maryam; Doozandeh, Maryam; Abbasi, Sanaz

    2016-01-01

    Background Combined amalgam-composite restorations have been used through many years to benefit from the advantages of both dental amalgam and composite resin. Two variations have been mentioned for this technique, this study investigated the fracture resistance of maxillary premolar teeth with extended mesio-occluso-distal (MOD) cavities, restored with the two variations of combined amalgam-composite restorations. Material and Methods Sixty intact extracted premolar teeth were randomly divided into 6 groups (G1-G6) of 10 teeth. G1; consisted of intact teeth and G2; consisted of teeth with MOD preparations were assigned as the positive and negative control groups respectively. Other experimental groups after MOD preparations were as follows: G3, amalgam restoration; G4, composite restoration; G5 combined amalgam-composite restoration with amalgam placement only on 1mm of the gingival floor of the proximal boxes; G6, combined amalgam-composite restoration with amalgam placement to the height of contact area of the proximal surface of the tooth. Fracture strength of the specimens was measured and the data were analyzed using one-way analysis of variance (ANOVA). The level of significance was Pamalgam-composite restoration was similar to that achieved with composite restoration alone and more than that of amalgam restoration alone. It can be concluded that the thickness of amalgam in combined amalgam-composite restorations did not affect fracture resistance of the teeth. Key words:Amalgam, composite, fracture resistance, restoration. PMID:27398176

  4. Influence of additives on oxidation resistance of binderless C/C composite

    Institute of Scientific and Technical Information of China (English)

    周声劢; 刘其城; 胡晓凯

    2003-01-01

    Experiment of adding B4C, SiC, and Si powders to improve oxidation resistance of the C/C compositeswas carried out. The results show that the increase of oxidation resistance is remarkable when the contents of B4C,SiC, and Si powders are 10%, 10%, and 5% in the composites, respectively. The regularities and mechanism ofthe effects of the ceramic powders on the oxidation resistance of the composites were also discussed.

  5. Glyphosate affects seed composition in glyphosate-resistant soybean.

    Science.gov (United States)

    Zobiole, Luiz H S; Oliveira, Rubem S; Visentainer, Jesui V; Kremer, Robert J; Bellaloui, Nacer; Yamada, Tsuioshi

    2010-04-14

    The cultivation of glyphosate-resistant (GR) soybeans has continuously increased worldwide in recent years mainly due to the importance of glyphosate in current weed management systems. However, not much has been done to understand eventual effects of glyphosate application on GR soybean physiology, especially those related to seed composition with potential effects on human health. Two experiments were conducted to evaluate the effects of glyphosate application on GR soybeans compared with its near-isogenic non-GR parental lines. Results of the first experiment showed that glyphosate application resulted in significant decreases in shoot nutrient concentrations, photosynthetic parameters, and biomass production. Similar trends were observed for the second experiment, although glyphosate application significantly altered seed nutrient concentrations and polyunsaturated fatty acid percentages. Glyphosate resulted in significant decreases in polyunsaturated linoleic acid (18:2n-6) (2.3% decrease) and linolenic acid (18:3n-3) (9.6% decrease) and a significant increase in monounsaturated fatty acids 17:1n-7 (30.3% increase) and 18:1n-7 (25% increase). The combined observations of decreased photosynthetic parameters and low nutrient availability in glyphosate-treated plants may explain potential adverse effects of glyphosate in GR soybeans.

  6. IMPACT RESISTANCE OF FIBER HOOP-WRAPPED COMPOSITE CYLINDERS%纤维环向缠绕复合材料气瓶冲击阻抗性能研究

    Institute of Scientific and Technical Information of China (English)

    张永明; 李培宁

    2013-01-01

    新能源汽车用复合材料气瓶采用复合材料/金属混杂结构,其冲击损伤特性与采用纯复合材料结构有很大的不同,本文结合复合材料气瓶和试板模拟试验,采用冲击能量吸收率、分层损伤扩展阻力、剩余强度比衰减指数等参数作为其冲击阻抗性能的评价指标.采用不同的支撑夹具对玻纤/环氧单向板进行落球冲击试验,以模拟复合材料气瓶的不同材质内胆对纤维缠绕层冲击损伤的影响.研究发现,在一定冲击能量作用下,改变复合材料/金属混杂结构的形式能使其冲击能量吸收率发生变化,并可提高层合板的冲击损伤临界值,即提高其冲击承载能力;冲击能量吸收率越高分层损伤扩展阻力越小,且含冲击损伤层合板的剩余强度衰减越快.因此在设计复合材料气瓶时,需要考虑复合材料/金属混杂结构对分层损伤扩展阻力和冲击能量吸收率的影响.%The composite / metal hybrid structure is widely used in composite cylinders of new energy vehicles, which has different impact damage characteristics compared with pure composite structure. This paper, combining both the tests of composite cylinder and test panel, evaluates impact resistance performance with parameters such as; impact energy absorption rate, delamination extension resistance and attenuation factor of the residual strength ratio. The experiments of falling ball impact with various support fixtures and glass fiber/epoxy unidirectional laminates are carried out to simulate how different liner materials of composite cylinders affect the impact damage degree of fiber winding layers. It is found that, under certain impact energy, changing composite / metal hybrid structure leads to the change of impact energy absorption rate and increases critical value of impact damage, namely, bear load impact capacity. The higher impact energy absorption rate will reduce delamination extension resistance, and the residual

  7. Improving the Thermal Shock Resistance of Thermal Barrier Coatings Through Formation of an In Situ YSZ/Al2O3 Composite via Laser Cladding

    Science.gov (United States)

    Soleimanipour, Zohre; Baghshahi, Saeid; Shoja-razavi, Reza

    2017-04-01

    In the present study, laser cladding of alumina on the top surface of YSZ thermal barrier coatings (TBC) was conducted via Nd:YAG pulsed laser. The thermal shock behavior of the TBC before and after laser cladding was modified by heating at 1000 °C for 15 min and quenching in cold water. Phase analysis, microstructural evaluation and elemental analysis were performed using x-ray diffractometry, scanning electron microscopy (SEM), and energy-dispersive spectroscopy. The results of thermal shock tests indicated that the failure in the conventional YSZ (not laser clad) and the laser clad coatings happened after 200 and 270 cycles, respectively. The SEM images of the samples showed that delamination and spallation occurred in both coatings as the main mechanism of failure. Formation of TGO was also observed in the fractured cross section of the samples, which is also a main reason for degradation. Thermal shock resistance in the laser clad coatings improved about 35% after cladding. The improvement is due to the presence of continuous network cracks perpendicular to the surface in the clad layer and also the thermal stability and high melting point of alumina in Al2O3/ZrO2 composite.

  8. Floating Carpets and the Delamination of Elastic Sheets

    KAUST Repository

    Wagner, Till J. W.

    2011-07-22

    We investigate the deformation of a thin elastic sheet floating on a liquid surface and subject to a uniaxial compression. We show that at a critical compression the sheet delaminates from the liquid over a finite region forming a delamination "blister." This blistering regime adds to the wrinkling and localized folding regimes that have been studied previously. The transition from wrinkled to blistered states occurs when delamination becomes energetically favorable compared with wrinkling. We determine the initial blister size and the evolution of blister size with continuing compression before verifying our theoretical results with experiments at a macroscopic scale. © 2011 American Physical Society.

  9. Microscale mechanics for metal thin film delamination along ceramic substrates

    Institute of Scientific and Technical Information of China (English)

    魏悦广

    2000-01-01

    The metal thin film delamination along metal/ceramic interface in the case of large scale yielding is studied by employing the strain gradient plasticity theory and the material microscale effects are considered. Two different f racture process models are used in this study to describe the nonlinear delamination phenomena for metal thin films. A set of experiments have been done on the mechanism of copper films delaminating from silica substrates, based on which the peak interface separation stress and the micro-length scale of material, as well as the dislocation-free zone size are predicted.

  10. Microscale mechanics for metal thin film delamination along ceramic substrates

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The metal thin film delamination along metal/ceramic interface in the case of large scale yielding is studied by employing the strain gradient plasticity theory and the material microscale effects are considered.Two different fracture process models are used in this study to describe the nonlinear delamination phenomena for metal thin films.A set of experiments have been done on the mechanism of copper films delaminating from silica substrates,based on which the peak interface separation stress and the micro-length scale of material,as well as the dislocation-free zone size are predicted.

  11. Delaminated graphene at silicon carbide facets: atomic scale imaging and spectroscopy.

    Science.gov (United States)

    Nicotra, Giuseppe; Ramasse, Quentin M; Deretzis, Ioannis; La Magna, Antonino; Spinella, Corrado; Giannazzo, Filippo

    2013-04-23

    Atomic-resolution structural and spectroscopic characterization techniques (scanning transmission electron microscopy and electron energy loss spectroscopy) are combined with nanoscale electrical measurements (conductive atomic force microscopy) to study at the atomic scale the properties of graphene grown epitaxially through the controlled graphitization of a hexagonal SiC(0001) substrate by high temperature annealing. This growth technique is known to result in a pronounced electron-doping (∼10(13) cm(-2)) of graphene, which is thought to originate from an interface carbon buffer layer strongly bound to the substrate. The scanning transmission electron microscopy analysis, carried out at an energy below the knock-on threshold for carbon to ensure no damage is imparted to the film by the electron beam, demonstrates that the buffer layer present on the planar SiC(0001) face delaminates from it on the (112n) facets of SiC surface steps. In addition, electron energy loss spectroscopy reveals that the delaminated layer has a similar electronic configuration to purely sp2-hybridized graphene. These observations are used to explain the local increase of the graphene sheet resistance measured around the surface steps by conductive atomic force microscopy, which we suggest is due to significantly lower substrate-induced doping and a resonant scattering mechanism at the step regions. A first-principles-calibrated theoretical model is proposed to explain the structural instability of the buffer layer on the SiC facets and the resulting delamination.

  12. Damage Threshold Characterization in Structural Composite Materials and Composite Joints

    Science.gov (United States)

    2010-02-28

    polyester, vinyl ester and epoxy, as reported earlier [1-3], the differences between resins are significant. The Vectorply ELT 5500 fabric (D) contains a...Delamination Testing,” AIAA Journal , vol. 28, 1990, pp. 1270-1276. 15. Agastra, P., "Mixed Mode Delamination of Glass Fiber/Polymer Matrix Composite

  13. Buckling-driven delamination in layered spherical shells

    Science.gov (United States)

    Sørensen, Kim D.; Jensen, Henrik M.

    An analysis of buckling-driven delamination of a layer in a spherical, layered shell has been carried out. The effects of the substrate having a double curvature compared to previous studies of delamination on cylindrical substrates turn out to be non-trivial in the sense that additional to the effect of the shape of the substrate, a new non-dimensional geometrical parameter enters the conditions for steady-state delamination. It is shown that this additional geometrical parameter in most cases of practical relevance has insignificant influence on the fracture mechanical parameters involved for the problem. The consequence is that solutions need to be mapped as a function of one rather than two dimensionless parameters. Furthermore, the shape of the substrate has profound influence especially on initiation of delamination growth.

  14. Contribution to interplay between a delamination test and a sensory analysis of mid-range lipsticks.

    Science.gov (United States)

    Richard, C; Tillé-Salmon, B; Mofid, Y

    2016-02-01

    Lipstick is currently one of the most sold products of cosmetics industry, and the competition between the various manufacturers is significant. Customers mainly seek products with high spreadability, especially long-lasting or long wear on the lips. Evaluation tests of cosmetics are usually performed by sensory analysis. This can then represent a considerable cost. The object of this study was to develop a fast and simple test of delamination (objective method with calibrated instruments) and to interplay the obtained results with those of a discriminative sensory analysis (subjective method) in order to show the relevance of the instrumental test. Three mid-range lipsticks were randomly chosen and were tested. They were made of compositions as described by the International Nomenclature of Cosmetic Ingredients (INCI). Instrumental characterization was performed by texture profile analysis and by a special delamination test. The sensory analysis was voluntarily conducted with an untrained panel as blind test to confirm or reverse the possible interplay. The two approaches or methods gave the same type of classification. The high-fat lipstick had the worst behaviour with the delamination test and the worst notation of the intensity of descriptors with the sensory analysis. There is a high correlation between the sensory analysis and the instrumental measurements in this study. The delamination test carried out should permit to quickly determine the lasting (screening test) and in consequence optimize the basic formula of lipsticks. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  15. Utilization of Large Cohesive Interface Elements for Delamination Simulation

    DEFF Research Database (Denmark)

    Bak, Brian Lau Verndal; Lund, Erik

    2012-01-01

    This paper describes the difficulties of utilizing large interface elements in delamination simulation. Solutions to increase the size of applicable interface elements are described and cover numerical integration of the element and modifications of the cohesive law.......This paper describes the difficulties of utilizing large interface elements in delamination simulation. Solutions to increase the size of applicable interface elements are described and cover numerical integration of the element and modifications of the cohesive law....

  16. Electrical Resistance Behavior of Vinylester Composites Filled with Glass-carbon Hybrid Fibers

    Institute of Scientific and Technical Information of China (English)

    WANG Jun; ZHANG Lianmeng; XU Renxin; DUAN Huajun; YANG Xiaoli; WANG Xiang

    2009-01-01

    Vinylester (bismethacryloxy derivative of a bisphenol-A type EP resin, VE) composites with glass-carbon hybrid fibers (CF-GF) weight fraction of 50%, were prepared by the compress molding method. The distribution of carbon fiber in the hybrids was observed by stereomicroscope. The electrical resistance behavior of the composites filled with different carbon fiber (CF) weight contents (0.5% to 20%) was studied. The experimental results show that the electrical resistance behaviors of CF-GF/VE composites are different with those of CF/VE composites because carbon fibers' conducting networks are broken by the glass fibers in the CF-GF/VE composites. The carbon fibers distribute uniformly in the networks of glass fibers (GF) like single silk and form the semi-continuous conducting networks. Composite filled with GF-CF hybrid has a higher percolation threshold than that filled with pure CF. At that time, the resistivity of CF-GF/VE composites varies little with the temperature increasing. The temperature coefficient of resistivity in GF-CF/VE composite is less than 317 ppm and the variation of the resistivity after ten thermal cycles from 20 ℃to 240 ℃ is less than 1.96%.

  17. Buckle Driven Delamination in Thin Hard Film Compliant Substrate Systems

    Directory of Open Access Journals (Sweden)

    Bahr D.F.

    2010-06-01

    Full Text Available Deformation and fracture of thin films on compliant substrates are key factors constraining the performance of emerging flexible substrate devices. [1-3] These systems often contain layers of thin polymer, ceramic and metallic films and stretchable interconnects where differing properties induce high normal and shear stresses. [4] As long as the films remain bonded to the substrates, they may deform far beyond their freestanding form. Once debonded, substrate constraint disappears leading to film failure. [3] Experimentally it is very difficult to measure properties in these systems at sub-micron and nanoscales. Theoretically it is very difficult to determine the contributions from the films, interfaces, and substrates. As a result our understanding of deformation and fracture behavior in compliant substrate systems is limited. This motivated a study of buckle driven delamination of thin hard tungsten films on pure PMMA substrates. The films were sputter deposited to thicknesses of 100 nm, 200 nm, and 400 nm with a residual compressive stress of 1.7 GPa. An aluminum oxide interlayer was added on several samples to alter interfacial composition. Buckles formed spontaneously on the PMMA substrates following film deposition. On films without the aluminum oxide interlayer, an extensive network of small telephone cord buckles formed following deposition, interspersed with regions of larger telephone cord buckles. (Figure 1 On films with an aluminum oxide interlayer, telephone cord buckles formed creating a uniform widely spaced pattern. Through-substrate optical observations revealed matching buckle patterns along the film-substrate interface indicating that delamination occurred for large and small buckles with and without an interlayer. The coexistence of large and small buckles on the same substrate led to two distinct behaviors as shown in Figure 2 where normalized buckle heights are plotted against normalized film stress. The behaviors deviate

  18. Buckle Driven Delamination in Thin Hard Film Compliant Substrate Systems

    Science.gov (United States)

    Moody, N. R.; Reedy, E. D.; Corona, E.; Adams, D. P.; Kennedy, M. S.; Cordill, M. J.; Bahr, D. F.

    2010-06-01

    Deformation and fracture of thin films on compliant substrates are key factors constraining the performance of emerging flexible substrate devices. [1-3] These systems often contain layers of thin polymer, ceramic and metallic films and stretchable interconnects where differing properties induce high normal and shear stresses. [4] As long as the films remain bonded to the substrates, they may deform far beyond their freestanding form. Once debonded, substrate constraint disappears leading to film failure. [3] Experimentally it is very difficult to measure properties in these systems at sub-micron and nanoscales. Theoretically it is very difficult to determine the contributions from the films, interfaces, and substrates. As a result our understanding of deformation and fracture behavior in compliant substrate systems is limited. This motivated a study of buckle driven delamination of thin hard tungsten films on pure PMMA substrates. The films were sputter deposited to thicknesses of 100 nm, 200 nm, and 400 nm with a residual compressive stress of 1.7 GPa. An aluminum oxide interlayer was added on several samples to alter interfacial composition. Buckles formed spontaneously on the PMMA substrates following film deposition. On films without the aluminum oxide interlayer, an extensive network of small telephone cord buckles formed following deposition, interspersed with regions of larger telephone cord buckles. (Figure 1) On films with an aluminum oxide interlayer, telephone cord buckles formed creating a uniform widely spaced pattern. Through-substrate optical observations revealed matching buckle patterns along the film-substrate interface indicating that delamination occurred for large and small buckles with and without an interlayer. The coexistence of large and small buckles on the same substrate led to two distinct behaviors as shown in Figure 2 where normalized buckle heights are plotted against normalized film stress. The behaviors deviate significantly from

  19. Structure and Catalytic Hydroxylation of Mixed Iron-Aluminum Oxide/Montmorillonite Composites with Ordered Mesostructure Prepared by Combined Pillaring and Delamination%介孔铁铝/蒙脱土复合材料:解离柱撑制备、结构及催化羟基化性能

    Institute of Scientific and Technical Information of China (English)

    周春晖; 童东绅; 葛忠华; 李杰; 罗锡平; 李小年

    2006-01-01

    利用极稀悬浮液中蒙脱土的解离作用并结合柱化技术过程,制备了介孔结构的铝铁/蒙脱土复合材料(Fe-Al/mmt);并采用粉末X射线衍射、氮等温吸脱附、傅立叶红外光谱、紫外可见光漫反射光谱及苯酚催化羟基化反应表征了其结构和性能.结果显示,铁铝聚合前驱液中铁/铝比影响复合材料中蒙脱土的解离程度,且仅当低铁/铝比时(即Fe/(Fe+Al)物质的量的比介于0.05~0.3),嵌入解离的蒙脱土片层间的混合铁铝物种呈现能耐温350℃的热稳定性;氮等温吸脱附分析反映出这种解离的蒙脱土堆积结构呈现介孔特征,孔径分布窄,介于2.0~2.3 nm;红外分析表明材料表面具有L酸和B酸位,并且L酸位量与嵌入解离的蒙脱土结构中的混合铁铝物种相关;由于结构中混合铁铝物种的存在及相应的Si-O→Fe、Al-O→Fe间的电子跃迁,Fe-Al/mmt材料在紫外区呈现宽泛的能量吸收特征.这些结果说明,由于混合铁铝物种嵌入于解离的蒙脱土片层堆积结构中,形成了"卡片屋"式介孔结构.实验条件下,Fe/(Fe+Al)物质的量的比为0.3的Fe-Al/mmt呈现较佳的催化羟基化性能,苯酚转化率为36.7%,二酚产物选择性32.3%;并且初步表明铝掺杂后,通过铁铝比和表面酸性的调整,材料的部分选择氧化性能可以得到改善.%Using delamination of the ultra dilute montmorillonite (mmt) suspension and pillaring techniques, the mixed Fe-Al/montmorillonite (Fe-Al/mmt) composites with mesoporous structure have been synthesized. Powder X-ray diffraction (XRD), N2 adsorption-desorption isotherms, Fourier transform infrared spectroscopy (FTIR), UVVis-diffuse reflectance spectroscopy (UV-Vis-DRS) and catalytic hydroxylation of phenol with H2O2 were used to characterize the samples. The XRD results suggest that the content of Fe plays an important role in the delaminating degree of mmt owing to flocculation of Fe-Al polyoxycations precursors. Only

  20. Compressive strength of thick composite panels

    DEFF Research Database (Denmark)

    Branner, Kim; Berring, Peter

    2011-01-01

    The aim of this study is to investigate how much the compressive strength of thick composite panels is reduced due to delaminations and to investigate under which conditions a delamination will grow. Understanding of this is essential in order to move forward the design limits used in the structu......The aim of this study is to investigate how much the compressive strength of thick composite panels is reduced due to delaminations and to investigate under which conditions a delamination will grow. Understanding of this is essential in order to move forward the design limits used...

  1. Hydrofluoric acid-resistant composite window and method for its fabrication

    Science.gov (United States)

    Ostenak, C.A.; Mackay, H.A.

    1985-07-18

    A hydrofluoric acid-resistant composite window and method for its fabrication are disclosed. The composite window comprises a window having first and second sides. The first side is oriented towards an environment containing hydrofluoric acid. An adhesive is applied to the first side. A layer of transparent hydrofluoric acid-resistant material, such as Mylar, is applied to the adhesive and completely covers the first side. The adhesive is then cured.

  2. Composites for Increased Wear Resistance: Current Achievements and Future Prospects

    Science.gov (United States)

    Lancaster, J. K.

    1984-01-01

    The various ways in which reductions in wear and/or friction can be achieved by the use of composite materials are reviewed. Reinforced plastics are emphasized and it is shown that fillers and fibers reduce wear via several mechanisms additional to their role of increasing overall mechanical strength, preferential transfer, counter face abrasion, preferential load support, or third-body formation on either the composite or its counterface. Examples are given from recent work on thin layer composites of the type widely used as dry bearings in aircraft flight control mechanisms. Developments in metal based composites and carbon-carbon composites for high energy brakes are discussed. The aspects which could benefit by increased fundamental understanding identified and the types of composites which appear to have greatest potential for further growth are indicated.

  3. Oxidation-resistant interfacial coatings for continuous fiber ceramic composites

    Energy Technology Data Exchange (ETDEWEB)

    Stinton, D.P.; Besmann, T.M.; Bleier, A. [Oak Ridge National Lab., TN (United States); Shanmugham, S.; Liaw, P.K. [Univ. of Tennessee, Knoxville, TN (United States)

    1995-08-01

    Continuous fiber ceramic composites mechanical behavior are influenced by the bonding characteristics between the fiber and the matrix. Finite modeling studies suggest that a low-modulus interfacial coating material will be effective in reducing the residual thermal stresses that are generated upon cooling from processing temperatures. Nicalon{trademark}/SiC composites with carbon, alumina and mullite interfacial coatings were fabricated with the SiC matrix deposited using a forced-flow, thermal gradient chemical vapor infiltration process. Composites with mullite interfacial coatings exhibited considerable fiber pull-out even after oxidation and have potential as a composite system.

  4. Effects of composite scale on high temperature oxidation resistance of Fe-Cr-Ni heat resistant alloy

    Directory of Open Access Journals (Sweden)

    Wang Haitao

    2009-05-01

    Full Text Available Fe-Cr-Ni heat resistant alloys with aluminum and silicon addition, alone and in combination, were melted using an intermediate frequency induction furnace with a non-oxidation method. By the oxidation weight gain method, the oxidation resistances of the test alloys were determined at 1,200 ìC for 500 hours. According to the oxidation weight gains, the oxidation kinetic curves were plotted and the functions were regressed by the least squares method. The results show that the oxidation kinetic curves follow the power function of y = axb (a>0, 0compositions on oxidation resistance were studied further by analyses using X-ray diffraction (XRD and scanning electron microscope (SEM. It is found that the composite scale compounds of Cr2O3, メ-Al2O3, SiO2 and FeCr2O4, with compact structure and tiny grains, shows complete oxidation resistance at 1,200 ìC. When the composite scale lacks メ-Al2O3 or SiO2, it becomes weak in oxidation resistance with a loose structure. By the criterion of standard Gibbs formation free energy, the model of the nucleation and growth of the composite scale is established. The forming of the composite scale is the result of the competition of being oxidized and reduced between aluminum, silicon and the matrix metal elements of iron, chromium and nickel. The protection of the composite scale is analyzed essentially by electrical conductivity and strength properties.

  5. An Analytical Model for Predicting Stab Resistance of Flexible Woven Composites

    Science.gov (United States)

    Hou, Limin; Sun, Baozhong; Gu, Bohong

    2013-08-01

    Flexible woven composites have been widely used in geotextiles and light weight building structures. The stab resistance behavior of the flexible woven composite is an important factor for the application design. This paper reports an analytical model for predicting stab resistance of flexible woven composites under perpendicular stab with a blunt steel penetrator. The analytical model was established based on the microstructure and the deformation shape of the flexible woven composite under normal penetration. During the quasi-static stab penetration, the strain energies of warp and weft yarns and resins have been calculated. The stab resistance was calculated from the strain energies of the flexible woven composite. Furthermore, the contributions of the warp and weft yarns, resins to the stab resistance have been analyzed. It was found the three constituents have near the same contribution to the stab resistance. The higher value of weaving density, strength of yarns and especially the higher strength coating resins will lead the higher stab resistance. With the analytical model, the stab resistance would be expected to be designed in an efficient way with an acceptable precision.

  6. Pressure and temperature induced electrical resistance change in nano-carbon/epoxy composites

    NARCIS (Netherlands)

    Shen, J. T.; Buschhorn, S. T.; De Hosson, J. Th. M.; Schulte, K.; Fiedler, B.

    2015-01-01

    In this study, we investigate the changes of electrical resistance of the carbon black (CB) and carbon nanotube (CNT) filled epoxy composites upon compression, swelling and temperature variation. For all samples we observe a decrease of electrical resistance under compression, while an increase of

  7. Reactivity of Mg-Al hydrotalcites in solid and delaminated forms in ammonium carbonate solutions

    Science.gov (United States)

    Stoica, Georgiana; Santiago, Marta; Abelló, Sònia; Pérez-Ramírez, Javier

    2010-10-01

    Treatment of Mg-Al hydrotalcites (LDHs, layered double hydroxides) in aqueous (NH 4) 2CO 3 at 298 K leads to composites of dawsonite, hydrotalcite, and magnesium ammonium carbonate. The mechanism and kinetics of this transformation, ultimately determining the relative amounts of these components in the composite, depend on the treatment time (from 1 h to 9 days), the Mg/Al ratio in the hydrotalcite (2-4), and on the starting layered double hydroxide (solid or delaminated form). The materials at various stages of the treatment were characterized by inductive coupled plasma-optical emission spectroscopy, X-ray diffraction, transmission electron microscopy, infrared spectroscopy, thermogravimetry, and nitrogen adsorption at 77 K. The progressive transformation of hydrotalcite towards crystalline dawsonite and magnesium ammonium carbonate phases follows a dissolution-precipitation mechanism. A gradual decrease of the Mg/Al ratio in the resulting solids was observed in time due to magnesium leaching in the reacting medium. Dawsonite-hydrotalcite composite formation is favored at high aluminum contents in the starting hydrotalcite, while the formation of magnesium ammonium carbonate is favored at high Mg/Al ratios. The synthetic strategy comprising hydrotalcite delamination in formamide prior to aqueous (NH 4) 2CO 3 treatment is more reactive towards composite formation than starting from the bulk solid hydrotalcite.

  8. Resistance Welding of Thermoplastic Composites: Process and Performance

    NARCIS (Netherlands)

    Shi, H.

    2014-01-01

    Compared to thermoset composites, thermoplastic composites are drawing more and more attention by aircraft industries not only due to their excellent material properties but also due to their potentials to reduce cycle time and structure cost by using low-cost manufacturing technologies such as weld

  9. Fire Resistant Composite Closed Cell Foam and Nonwoven Textiles for Tents and Shelters

    Science.gov (United States)

    2006-01-01

    Shelter Prototype In order to produce sufficient foam, adhesive and coated nonwoven for construction of a small shelter, larger quantities were...AFRL-ML-TY-TR-2006-4571 FIRE RESISTANT COMPOSITE CLOSED CELL FOAM AND NONWOVEN TEXTILES FOR TENTS AND SHELTERS Stephen C. Davis...18 Figure 12. Screening Fire Test of Nonwoven and PVC/NBR Foam Composite

  10. Fracture strength and fatigue resistance of dental resin-based composites

    NARCIS (Netherlands)

    F. Keulemans; P. Palav; M.M.N. Aboushelib; A. van Dalen; C.J. Kleverlaan; A.J. Feilzer

    2009-01-01

    Objectives: The aim of this study was to evaluate in vitro the influence of fiber-reinforcement on the fracture strength and fatigue resistance of resin-based composites. Methods: One hundred rectangular bar-shaped specimens (2 mm × 2 mm × 25 mm) made of resin-based composite were prepared in a stai

  11. Hybrid carbon/glass fiber composites: Micromechanical analysis of structure–damage resistance relationships

    DEFF Research Database (Denmark)

    Mishnaevsky, Leon; Dai, Gaoming

    2014-01-01

    A computational study of the effect of microstructure of hybrid carbon/glass fiber composites on their strength is presented. Unit cells with hundreds of randomly located and misaligned fibers of various properties and arrangements are subject to tensile and compression loading, and the evolution...... of fiber damages is analyzed in numerical experiments. The effects of fiber clustering, matrix properties, nanoreinforcement, load sharing rules on the strength and damage resistance of composites are studied. It was observed that hybrid composites under uniform displacement loading might have lower...... strength than pure composites, while the strength of hybrid composites under inform force loading increases steadily with increasing the volume content of carbon fibers....

  12. Electrodeposition and Corrosion Resistance Properties of Zn-Ni/TiO2 Nano composite Coatings

    Directory of Open Access Journals (Sweden)

    B. M. Praveen

    2011-01-01

    Full Text Available Nano sized TiO2 particles were prepared by sol-gel method. TiO2 nano particles were dispersed in zinc-nickel sulphate electrolyte and thin film of Zn-Ni-TiO2 composite was generated by electrodeposition on mild steel plates. The effect of TiO2 on the corrosion behavior and hardness of the composite coatings was investigated. The film was tested for its corrosion resistance property using electrochemical, weight loss, and salt spray methods. The paper revealed higher resistance of composite coating to corrosion. Microhardness of the composite coating was determined. Scanning electron microscope images and X-ray diffraction patterns of coating revealed its fine-grain nature. Average crystalline size of the composite coating was calculated. The anticorrosion mechanism of the composite coating was also discussed.

  13. WEAR-RESISTANCE OF CHROMIC CAST IRONS OF EUTECTIC COMPOSITION

    Directory of Open Access Journals (Sweden)

    K. E. Baranovskij

    2009-01-01

    Full Text Available Casting of wear-resistant chrome cast irons in combined molds and iron chills is studied. Application of these ways of casting results in blending of carbides and increasing of hardness of castings.

  14. Method of making bearing materials. [self-lubricating, oxidation resistant composites for high temperature applications

    Science.gov (United States)

    Sliney, H. E. (Inventor)

    1979-01-01

    A method is described for making a composite material which provides low friction surfaces for materials in rolling or sliding contact. The composite material which is self-lubricating and oxidation resistant up to and in excess of about 930 C is comprised of a metal component which lends strength and elasticity to the structure and a fluorine salt component which provides oxidation protection to the metal but may also enhance the lubrication qualities of the composite.

  15. Characterizing Delamination Migration in Carbon/Epoxy Tape Laminates

    Science.gov (United States)

    Ratcliffe, James G.; Czabaj, Michael W.; Obrien, Thomas K.

    2012-01-01

    A new test method is presented for the purpose of investigating migration of a delamination between neighboring ply interfaces in fiber-reinforced, polymer matrix tape laminates. The test is a single cantilever beam configuration consisting of a cross-ply laminate with a polytetrafluoroethylene (PTFE) insert implanted at the mid-plane and spanning part way along the length of the specimen. The insert is located between a 0-degree ply (specimen length direction) and a stack of four 90-degree plies (specimen width direction). The specimen is clamped at both ends onto a rigid baseplate and is loaded on its upper surface via a piano hinge. Tests were conducted with the load-application point located on the intact portion of the specimen in order to initiate delamination growth onset followed by migration of the delamination to a neighboring 90/0 ply interface by kinking through the 90- degree ply stack. Varying this position was found to affect the distance relative to the load-application point at which migration initiated. In each specimen, migration initiated by a gradual transition of the delamination at the 0/90 interface into the 90- degree ply stack. In contrast, transition of the kinked crack into the 90/0 interface was sudden. Fractography of the specimens indicated that delamination prior to migration was generally mixed mode-I/II. Inspection of the kink surface revealed mode-I fracture. In general, use of this test allows for the observation of the growth of a delamination followed by migration of the delamination to another ply interface, and should thus provide a means for validating analyses aimed at simulating migration.

  16. Study on dry friction and wear resistance of a WC-Co particle reinforced iron matrix composite material

    OpenAIRE

    Zhang Peng; Zeng Shaolian; Zhang Zhiguo

    2013-01-01

    In order to select a suitable material for the rolling mill guide application, the dry sliding friction and wear resistance of a tungsten carbide combining cobalt (WC-Co) particle reinforced chromium cast iron composite material were studied. In particular, the wear resistance was discussed in detail. The results showed that the composite material demonstrates 25 times the wear resistance of high Cr cast iron, and 9 times the wear resistance of heat resistant steel. However, the average frict...

  17. Fracture resistance curves and toughening mechanisms in polymer based dental composites

    DEFF Research Database (Denmark)

    De Souza, J.A.; Goutianos, Stergios; Skovgaard, M.

    2011-01-01

    The fracture resistance (R-curve behaviour) of two commercial dental composites (Filtek Z350® and Concept Advanced®) were studied using Double Cantilever Beam sandwich specimens loaded with pure bending moments to obtain stable crack growth. The experiments were conducted in an environmental...... significantly higher fracture resistance than the composite with the coarser microstructure. The fracture properties were related to the flexural strength of the dental composites. The method, thus, can provide useful insight into how the microstructure enhances toughness, which is necessary for the future...

  18. Preparation of novel functional Mg/O/PCL/ZnO composite biomaterials and their corrosion resistance

    Energy Technology Data Exchange (ETDEWEB)

    Xi, Zhongxian; Tan, Cui; Xu, Lan; Yang, Na; Li, Qing, E-mail: liqingdswu@163.com

    2015-10-01

    Highlights: • Novel functional Mg/O/PCL/ZnO composite biomaterials were prepared. • The biomaterials were prepared by anodization treatment and dip-coating technique. • The composite biomaterials were smooth and with low porosity. • The prepared biomaterials have good corrosion resistance in SBF. • The composite biomaterials can release zinc ion to promote bone formation. - Abstract: In this study, novel and functional Mg/O/PCL/ZnO (magnesium/anodic film/poly(ε-caprolactone)/zinc oxide) composite biomaterials for enhancing the bioactivity and biocompatibility of the implant was prepared by using anodization treatment and dip-coating technique. The surface morphology, microstructure, adhesion strength and corrosion resistance of the composite biomaterials were investigated using scanning electron microscopy (SEM), adhesion measurements, electrochemical tests and immersion tests respectively. In addition, the biocompatible properties of Mg (magnesium), Mg/PCL (magnesium/poly(ε-caprolactone)) and Mg/O/PCL (magnesium/anodic film/poly(ε-caprolactone)) samples were also investigated. The results show that the Mg/O/PCL/ZnO composite biomaterials were with low porosity and with the ZnO powders dispersed in PCL uniformly. The adhesion tests suggested that Mg/O/PCL/ZnO composite biomaterials had better adhesion strength than that of Mg/PCL composite biomaterials obviously. Besides, an in vitro test for corrosion demonstrated that the Mg/O/PCL/ZnO composite biomaterials had good corrosion resistance and zinc ion was released obviously in SBF.

  19. Propolis chemical composition and honeybee resistance against Varroa destructor.

    Science.gov (United States)

    Popova, M; Reyes, M; Le Conte, Y; Bankova, V

    2014-01-01

    Propolis is known as honeybee chemical defence against infections and parasites. Its chemical composition is variable and depends on the specificity of the local flora. However, there are no data concerning the relationship between propolis chemical composition and honeybee colony health. We tried to answer this question, studying the chemical composition of propolis of bee colonies from an apiary near Avignon, which are tolerant to Varroa destructor, comparing it with colonies from the same apiary which are non-tolerant to the mites. The results indicated that non-tolerant colonies collected more resin than the tolerant ones. The percentage of four biologically active compounds - caffeic acid and pentenyl caffeates - was higher in propolis from tolerant colonies. The results of this study pave the way to understanding the effect of propolis in individual and social immunity of the honeybees. Further studies are needed to clarify the relationship between propolis chemical composition and honeybee colony health.

  20. Fracture Resistance of Composite Veneers with Different Preparation Designs

    OpenAIRE

    Zlatanovska, Katerina; Guguvcevski, Ljuben; Popovski, Risto; Dimova, Cena; Minovska, Ana; Mijoska, Aneta

    2016-01-01

    Background: The aim of this in vitro study was to examine the fracture load of composite veneers using three different preparation designs. Material and methods: Fifteen extracted, intact, human maxillary central incisors were selected. Teeth were divided into three groups with different preparation design: 1) feather preparation, 2) bevel preparation, and 3) incisal overlap- palatal chamfer. Teeth were restored with composite veneers, and the specimens were loaded to failure. The localizatio...

  1. Comparative Study of Wear Resistance of the Composite with Microhybrid Structure and Nanocomposite

    Directory of Open Access Journals (Sweden)

    Pieniak Daniel

    2016-12-01

    Full Text Available The aim of the study was to compare microhardness and wear resistance of ceramic-polymer composites with micro and nano-hybrid structure. For the studies commercial composites were used, containing filler particles of the same type but different sizes, nano-sized (Filtek Ultimate and micro-sized (Filtek Z250 composites. Tribological testing was conducted using ball-on-disc micro-tribometer. Vickers testing method was applied for microhardness studies with the use of Futertech FM 700 device. It has been demonstrated that the wear of Filtek Ultimate is almost twice lower in comparison to wear of Filtek Z250 composite. It has been concluded that the use of filler nanoparticles significantly increased wear resistance of the material. Additionally, lack of correlation between material microhardness and wear resistance has been demonstrated.

  2. Thermal analysis of resin composites with ellipsoidal filler considering thermal boundary resistance

    Science.gov (United States)

    Asakuma, Yusuke; Yamamoto, Tsuyoshi

    2016-10-01

    The effective thermal conductivity of composites with ellipsoidal fillers is analyzed by using a homogenization method that is able to represent the microstructure precisely. In this study, various parameters such as the volume fraction, shape, and distribution of the filler are quantitatively estimated to understand the mechanisms of heat transfer in the composite. First, thermal boundary resistance between resin and filler is important for obtaining composites with higher thermal conductivity. Second, the anisotropy of the effective thermal conductivity arises from contact between filler in the case of ellipsoidal filler and produces lower thermal resistance. Finally, the filler network and thermal resistance are essential for the heat transfer in composites because the path of thermal conduction is improved by contact between neighboring filler particles.

  3. MR imaging of delamination tears of the rotator cuff tendons

    Energy Technology Data Exchange (ETDEWEB)

    Walz, Daniel M.; Chen, Steven [North Shore University Hospital, Department of Radiology, Manhasset, NY (United States); Miller, Theodore T. [Hospital for Special Surgery, Department of Radiology and Imaging, New York, NY (United States); Hofman, Josh [Long Island Jewish Medical Center, New Hyde Park, NY (United States)

    2007-05-15

    The objective was to describe the imaging appearances and location of delamination tears of the rotator cuff tendons on non-contrast conventional MR imaging. This study was reviewed and approved by our Institutional Review Board. The reports of 548 consecutive MR examinations of the shoulder were reviewed, looking for mention or description of delamination tears of the rotator cuff. The images of the identified cases were then reviewed by two radiologists to confirm the findings. Correlation with surgical and arthroscopic information was then performed. Delamination tears were defined as horizontal retraction of either the bursal or articular surface of the tendon, manifest as thickening of the torn retracted edge, and/or interstitial splitting of the tendon, manifest as fluid-like high signal intensity on fat-suppressed T2-weighted oblique coronal images. Fourteen cases of delamination tears were identified in 13 patients. Ten of the cases involved the supraspinatus tendon, all with articular surface involvement. Nine of these supraspinatus cases were isolated tears and one occurred as part of a full thickness tear. All 10 of these supraspinatus cases showed medial retraction of the articular surface of the tendon, with thickening of the retracted edge, and 5 of the 10 had a demonstrable horizontal cleft in the interstitium. Four cases involved the subscapularis tendon, with articular surface disruption in three and pure interstitial delamination in one. Medial subluxation of the tendon of the long head of the biceps was present in all four cases. No delamination tears occurred on the bursal surface. Only three of the 14 shoulders underwent surgical repair with one confirmation of supraspinatus delamination, one confirmation of a subscapularis tear that had become a full thickness tear 10 months after initial imaging and another interstitial subscapularis delamination that was not identified arthroscopically. Delamination tears occur most often in the

  4. Electrical resistivity and piezoresistivity of Ni-CNT filled epoxy-based composites

    Science.gov (United States)

    Jiang, Jinbao; Xiao, Huigang; Li, Hui

    2013-04-01

    This paper investigates properties about electrical resistivity and piezoresistivity of multi-wall carbon nanotubes (MWCNTs)-filled epoxy-based composite and its further use for strain sensing. The MWCNTs dispersed epoxy resin, using MWCNTs in the amount of 1.5~3.0 vol.%, was first prepared by combined high-speed stirring and sonication methods. Then, the MWCNTs dispersed epoxy resin was cast into an aluminum mold to form specimens measuring 10×10×36 mm. After curing, DC electrical resistance measurements were performed along the longitudinal axis using the four-probe method, in which copper nets served as electrical contacts. The percolation threshold zone of resistivity was got as MWCNTs in the amount of 2.00-2.50 vol.%. Further compressive testing of these specimens was conducted with four-probe method for resistance measurements at the same time. Testing results show that the electrical resistivity of the composites changes with the strain's development, namely piezoresistivity. While for practical strain sensing use, signals of electric resistance and current in the acquisition circuits were both studied. Results show that the signal of current, compared with that of resistance, had better linear relationship with the compressive strain, better stability and longer effective section to reflect the whole deformation process of the specimens under pressure. Further works about the effects of low magnetic field on the electrical resistivity and piezoresistivity of Ni-CNTs filled epoxy-based composites were presented briefly at the end of the paper.

  5. Microscopic mechanisms of graphene electrolytic delamination from metal substrates

    Science.gov (United States)

    Fisichella, G.; Di Franco, S.; Roccaforte, F.; Ravesi, S.; Giannazzo, F.

    2014-06-01

    In this paper, hydrogen bubbling delamination of graphene (Gr) from copper using a strong electrolyte (KOH) water solution was performed, focusing on the effect of the KOH concentration (CKOH) on the Gr delamination rate. A factor of ˜10 decrease in the time required for the complete Gr delamination from Cu cathodes with the same geometry was found increasing CKOH from ˜0.05 M to ˜0.60 M. After transfer of the separated Gr membranes to SiO2 substrates by a highly reproducible thermo-compression printing method, an accurate atomic force microscopy investigation of the changes in Gr morphology as a function of CKOH was performed. Supported by these analyses, a microscopic model of the delamination process has been proposed, where a key role is played by graphene wrinkles acting as nucleation sites for H2 bubbles at the cathode perimeter. With this approach, the H2 supersaturation generated at the electrode for different electrolyte concentrations was estimated and the inverse dependence of td on CKOH was quantitatively explained. Although developed in the case of Cu, this analysis is generally valid and can be applied to describe the electrolytic delamination of graphene from several metal substrates.

  6. Use of microfasteners to produce damage tolerant composite structures.

    Science.gov (United States)

    Partridge, Ivana K; Hallett, Stephen R

    2016-07-13

    The paper concerns the mechanical performance of continuous fibre/thermosetting polymer matrix composites reinforced in the through-thickness direction with fibrous or metallic rods or threads in order to mitigate against low delamination resistance. Specific illustrations of the effects of microfasteners in reducing delamination crack growth are made for Z-pinned and tufted composites. Response to loading in such 'structured materials' is subject to multiple parameters defining their in-plane and out-of-plane properties. Single microfastener mechanical tests are well suited to establish the crack bridging laws under a range of loading modes, from simple delamination crack opening to shear, and provide the basis for predicting the corresponding response of microfastener arrays, within a given material environment. The fundamental experiments on microfasteners can be used to derive analytical expressions to describe the crack bridging behaviour in a general sense, to cover all possible loadings. These expressions can be built into cohesive element constitutive laws in a finite-element framework for modelling the effects of microfastener arrays on the out-of-plane mechanical response of reinforced structural elements, including the effects of known manufacturing imperfections. Such predictive behaviour can then be used to assess structural integrity under complex loading, as part of the component design process. This article is part of the themed issue 'Multiscale modelling of the structural integrity of composite materials'.

  7. EBSD and Nanoindentation-Correlated Study of Delamination Fracture in Al-Li Alloy 2090

    Science.gov (United States)

    Tayon, Wesley A.; Crooks, Roy E.; Domack, Marcia S.; Wagner, John A.; Elmustafa, A. A.

    2008-01-01

    Al-Li alloys offer attractive combinations of high strength and low density. However, a tendency for delamination fracture has limited their use. A better understanding of the delamination mechanisms may identify methods to control delaminations through processing modifications. A combination of new techniques has been used to evaluate delamination fracture in Al-Li alloys. Both high quality electron backscattered diffraction (EBSD) information and valid nanoindentation measurements were obtained from fractured test specimens. Correlations were drawn between nano-scale hardness variations and local texture along delaminating boundaries. Intriguing findings were observed for delamination fracture through the combined analysis of grain orientation, Taylor factor, and kernel average misorientation.

  8. Effects of Mineral Composition and Microstructure on Crack Resistance of Sintered Ore

    Institute of Scientific and Technical Information of China (English)

    YING Zi-wei; JIANG Mao-fa; XU Li-xian

    2006-01-01

    Vickers indentation test was used to study the effects of mineral composition and microstructure on crack resistance of sintered ore, and the initiation and propagation of cracks in different minerals contained in sintered ore were examined. The results indicate that the microstructure of calcium ferrites is a major factor influencing crack resistance of sintered ore. Finer grain size of calcium ferrite will lead to higher cracking threshold and better crack resistance of sintered ore. The formation of calcium ferrite with fine grain size during sintering process is favorable for crack resistance of sintered ore.

  9. Fracture resistance of endodontically treated teeth restored with a bulkfill flowable material and a resin composite.

    Science.gov (United States)

    Isufi, Almira; Plotino, Gianluca; Grande, Nicola Maria; Ioppolo, Pietro; Testarelli, Luca; Bedini, Rossella; Al-Sudani, Dina; Gambarini, Gianluca

    2016-01-01

    To determine and compare the fracture resistance of endodontically treated teeth restored with a bulk fill flowable material (SDR) and a traditional resin composite. Thirty maxillary and 30 mandibular first molars were selected based on similar dimensions. After cleaning, shaping and filling of the root canals and adhesive procedures, specimens were assigned to 3 subgroups for each tooth type (n=10): Group A: control group, including intact teeth; Group B: access cavities were restored with a traditional resin composite (EsthetX; Dentsply-Italy, Rome, Italy); Group C: access cavities were restored with a bulk fill flowable composite (SDR; Dentsply-Italy), except 1.5 mm layer of the occlusal surface that was restored with the same resin composite as Group B. The specimens were subjected to compressive force in a material static-testing machine until fracture occurred, the maximum fracture load of the specimens was measured (N) and the type of fracture was recorded as favorable or unfavorable. Data were statistically analyzed with one-way analysis of variance (ANOVA) and Bonferroni tests (Presin composite and with a bulk fill flowable composite (SDR) was similar in both maxillary and mandibular molars and showed no significant decrease in fracture resistance compared to intact specimens. No significant difference was observed in the mechanical fracture resistance of endodontically treated molars restored with traditional resin composite restorations compared to bulk fill flowable composite restorations.

  10. Longitudinal shear resistance of composite slabs - Parameters affecting physical behaviour

    NARCIS (Netherlands)

    Stark, J.W.B.; Schuurman, R.G.; Brekelmans, J.W.P.M.

    2000-01-01

    The conversion of the ENV version of Eurocode 4 into an EN is under preparation and the question was raised whether the rules and/or testing procedures for the evaluation of the longitudinal shear resistance have to be improved. In this paper an overview is given of the various aspects influencing

  11. Calibration of a finite element composite delamination model by experiments

    DEFF Research Database (Denmark)

    Gaiotti, M.; Rizzo, C.M.; Branner, Kim;

    2013-01-01

    distinct sub-laminates. The work focuses on experimental validation of a finite element model built using the 9-noded MITC9 shell elements, which prevent locking effects and aiming to capture the highly non linear buckling features involved in the problem. The geometry has been numerically defined...... modes related to the production methods is presented in this paper. A microscopic analysis of the fracture surfaces was carried out in order to better understand the failure mechanisms. © 2013 Taylor & Francis Group....

  12. Producing cobalt–graphene composite coating by pulse electrodeposition with excellent wear and corrosion resistance

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Cansen; Su, Fenghua, E-mail: fhsu@scut.edu.cn; Liang, Jizhao

    2015-10-01

    Graphical abstract: - Highlights: • Graphene oxide/cobalt coatings are synthesized by pulse electrodeposition. • Incorporating GO refines the grain size and changes the microstructure of the coating. • Incorporating GO greatly improves the friction reduction and wear resistance of the coating. • The corrosion resistance is enhanced by the incorporation of GO. - Abstract: Cobalt (Co) and graphene oxide/cobalt (GO/Co) composite coatings were fabricated by pulse electrodeposition technique from an aqueous bath containing cobalt sulfate and GO, etc. Effect of the incorporations of GO on morphology, phase structure, average grain size and corrosion and wear resistance of the resulting composite coatings were evaluated in detail. Scanning electron microscope (SEM) and energy dispersed X-ray (EDX) show that the GO nanosheets disperse homogeneously in the composite coating and the incorporations of GO change the morphologies of the deposit from conical shaped structure to protruding structure. In addition, the co-deposition GO with Co ions favor the formation of hcp (1 0 0), (0 0 2) and (1 0 1) textures in the composite coating and have functions of grain refining and hardness enhancement. The wear tests show that the incorporations of GO in the coating improve the wear resistance and friction reduction of the deposit. The electrochemical corrosion tests using potentiodynamic polarization and electrochemical impedance spectroscopy show that the GO/Co composite coating possesses better corrosion resistance than the pure Co coating.

  13. Micromechanical models of delamination in aluminum-lithium alloys

    Science.gov (United States)

    Messner, Mark Christian

    Aluminum lithium (Al-Li) alloys are lighter, stiffer, and tougher than conventional aerospace aluminum alloys. Replacing conventional aluminums with Al-Li could substantially decrease the weight and cost of aerospace structures. However, Al-Li alloys often fracture intergranularly via a mechanism called delamination cracking. While secondary delamination cracks can improve the effective toughness of a component, no current model accurately predicts the initiation and growth of intergranular cracks. Since simulations cannot incorporate delamination into a structural model, designers cannot quantify the effect of delamination cracking on a particular component. This uncertainty limits the application of Al-Li alloys. Previous experiments identify microstructural features linked to delamination. Fractography of failed surfaces indicates plastic void growth triggers intergranular failure. Furthermore, certain types of soft/stiff grain boundaries tend to localize void growth and nucleate delamination cracks. This dissertation develops a mechanism for the initiation of delamination on the microscale that accounts for these experimental observations. Microscale simulations of grain boundaries near a long primary crack explore the delamination mechanism on the mesoscale. In these simulations, a physically-based crystal plasticity (CP) model represents the constitutive response of individual grains. This CP model incorporates plastic voriticity correction terms into a standard objective stress rate integration, to accurately account for the kinematics of lattice deformation. The CP model implements slip system hardening with a modular approach to facilitate quick testing and calibration of different theories of hardening. The microscale models reveal soft/stiff grain boundaries develop elevated mean stress and plastic strain as a consequence of the mechanics of the interface. These elevated stresses and strain drive plastic void growth. The results indicate plastic void

  14. A STEEL MATRIX WEAR RESISTANT COMPOSITE REINFORCED BY IN-SITU GRANULAR EUTECTICS

    Institute of Scientific and Technical Information of China (English)

    Z.M. Xu; T.X. Li; J.G. Li

    2001-01-01

    A new steel matrix wear resistant composite reinforced by in situ granular eutectics can be obtained by modifying with a Si-Ce-Ti compound in the steel melt. The result indicates that the in situ granular eutectic is a pseudo-eutectic of austenite and (Fe, Mn)3C, which is formed between austenite dendrites during solidification due to the segregation of C and Mn impelled by modifying elements. The quantity of in situ granular eutectic reaches up to 8% 12%, and its grain size is in the range from 10μm to 20μm. The austenite steel matrix wear resistant composite reinforced by in situ granular eutectic (abbreviated AGE composite) and austenite-bainite steel matrix wear resistant composite reinforced by in situ granular eutectic (abbreviated ABGE composite) are obtained in the as-cast state and by air hardening, respectively. The wear resistance of the AGE and ABGE composites can be more greatly increased than that of their matrix steels under low and medium impact working condition.

  15. Fatigue resistance of CAD/CAM resin composite molar crowns.

    Science.gov (United States)

    Shembish, Fatma A; Tong, Hui; Kaizer, Marina; Janal, Malvin N; Thompson, Van P; Opdam, Niek J; Zhang, Yu

    2016-04-01

    To demonstrate the fatigue behavior of CAD/CAM resin composite molar crowns using a mouth-motion step-stress fatigue test. Monolithic leucite-reinforced glass-ceramic crowns were used as a reference. Fully anatomically shaped monolithic resin composite molar crowns (Lava Ultimate, n=24) and leucite reinforced glass-ceramic crowns (IPS Empress CAD, n=24) were fabricated using CAD/CAM systems. Crowns were cemented on aged dentin-like resin composite tooth replicas (Filtek Z100) with resin-based cements (RelyX Ultimate for Lava Ultimate or Multilink Automix for IPS Empress). Three step-stress profiles (aggressive, moderate and mild) were employed for the accelerated sliding-contact mouth-motion fatigue test. Twenty one crowns from each group were randomly distributed among these three profiles (1:2:4). Failure was designated as chip-off or bulk fracture. Optical and electron microscopes were used to examine the occlusal surface and subsurface damages, as well as the material microstructures. The resin composite crowns showed only minor occlusal damage during mouth-motion step-stress fatigue loading up to 1700N. Cross-sectional views revealed contact-induced cone cracks in all specimens, and flexural radial cracks in 2 crowns. Both cone and radial cracks were relatively small compared to the crown thickness. Extending these cracks to the threshold for catastrophic failure would require much higher indentation loads or more loading cycles. In contrast, all of the glass-ceramic crowns fractured, starting at loads of approximately 450N. Monolithic CAD/CAM resin composite crowns endure, with only superficial damage, fatigue loads 3-4 times higher than those causing catastrophic failure in glass-ceramic CAD crowns. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  16. Repair of prestressed concrete cylinder with localized delamination

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shen, E-mail: swang@bechtel.com; Munshi, Javeed A., E-mail: jamunshi@bechtel.com

    2015-12-15

    For prestressed concrete cylindrical structures such as nuclear containments, tanks and silos, the curvature effect of the tendons introduces radial tensile stresses in the concrete shell which are generally neglected in the design of such structures. For example, many prestressed concrete nuclear containments in US, especially those which were not designed following radial reinforcement requirement of ACI-359, are reinforced only in the circumferential (hoop) and meridional (vertical) directions but not in the radial direction. This leaves these structures vulnerable to potential laminar cracking and delamination, especially during post-tensioning and/or detensioning process. Should delamination occur, the structure needs to be repaired by either replacing cracked concrete or by “pinning” the delaminated concrete layers together by post-installed anchors. The latter option of post-installed anchors is less invasive from construction stand point and generally suitable for repairing small or localized delamination only. A comprehensive study is undertaken to explore various aspects and design consideration of post-installed anchors for prestressed concrete cylinders. The radial tension demand is first established by combining a mechanical based model with a detailed finite element analysis. With such design demand for post-installed anchors established, the next step aims at developing the tightness requirement of existing delamination cracks for effective use of post-installed anchors. A comprehensive literature search and evaluation is carried out for shear transfer capacity across cracks of various widths. The findings are used to develop specific recommendations for acceptable crack widths to ensure adequate in-plane shear transfer capacity for various design load conditions. A design process for post-installed anchors is proposed for repairing a delaminated prestressed concrete cylindrical structure at the end of the paper, supplemented by an illustrative

  17. The postbuckling analysis of laminated circular plate with elliptic delamination

    Science.gov (United States)

    Chen, Deliang; Chen, Changping; Fu, Yiming

    2011-01-01

    Based on the Von Karman plate theory, considering the effect of transverse shear deformation, and using the method of the dissociated three regions, the postbuckling governing equations for the axisymmetric laminated circular plates with elliptical delamination are derived. By using the orthogonal point collocation method, the governing equations, boundary conditions and continuity conditions are transformed into a group of nonlinear algebraically equation and the equations are solved with the alternative method. In the numerical examples, the effects of various elliptical in shape, delamination depth and different material properties on buckling and postbuckling of the laminated circular plates are discussed and the numerical results are compared with available data.

  18. Thickness effect on electric resistivity on polystyrene and carbon black- based composites

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Lopez, S; Vigueras-Santiago, E [Laboratorio de Investigacion y Desarrollo de Materiales Avanzados (LIDMA) Facultad de Quimica, Paseo Colon Esquina con Paseo Tollocan, s/n, CP 50000, Toluca (Mexico); Mayorga-Rojas, M; Reyes-Contreras, D, E-mail: eviguerass@uaemex.m [Facultad de Ciencias, Universidad Autonoma del Estado de Mexico. Av. Instituto Literario 100 Ote. C. P. 50000, Toluca (Mexico)

    2009-05-01

    Changes on electrical resistivity were experimentally studied for polystyrene and carbon black-based composites respect to the temperature. 22% w/w carbon black composite films at 30{mu}m, 2mm y 1cm thick were submitted to thermal heating-cooling cycles from room temperature to 100 deg. C, slightly up to T{sub g} of the composite. For each cycle changes on electrical resistivity constituent a hysteresis loop that depends on the sample thickness. The changes during the heating stage could be explained as a consequence of the thermal expansion and mobility of the polymer chains at T{sub g}, producing a disconnecting of the electrical contacts among carbon black particles and an important increasing (200%) of the electrical resistivity. For each cycle, the hysteresis loop was observed in thicker samples, whereas for 30 mu m thickness sample the hysteresis loop was lost after four cycles.

  19. Development of impact resistant boron/aluminum composites for turbojet engine fan blades

    Science.gov (United States)

    Melnyk, P.; Toth, I. J.

    1975-01-01

    Composite fabrication was performed by vacuum press diffusion bonding by both the foil-filament array and preconsolidated monotape methods. The effect of matrix material, fiber diameter, matrix enhancement, fiber volume reinforcement, test temperature, angle-plying, notch, impact orientation, processing variables and fabrication methods on tensile strength and Charpy impact resistance are evaluated. Root attachment concepts, were evaluated by room and elevated temperature tensile testing, as well as by pendulum-Izod and ballistic impact testing. Composite resistance to foreign object damage was also evaluated by ballistic impacting of panels using projectiles of gelatin, RTV rubber and steel at various velocities, and impingement angles. A significant improvement in the pendulum impact resistance of B-Al composites was achieved.

  20. Lightweight Impact-Resistant Composite Materials: Lessons from Mantis Shrimp

    Science.gov (United States)

    Milliron, Garrett Wayne

    Nature has evolved efficient strategies to synthesize complex mineralized structures that exhibit exceptional damage tolerance. One such example is found in the hyper-mineralized hammer-like dactyl clubs of the stomatopods, a group of highly aggressive marine crustaceans. The dactyl clubs from one such species, Odontodactylus Scyllarus, exhibit an impressive set of characteristics adapted for surviving high velocity impacts with the heavily mineralized prey species on which they feed. Consisting of a multi-phase composite of oriented crystalline hydroxyapatite and amorphous calcium phosphate and carbonate, in conjunction with a highly expanded helicoidal organization of the fibrillar chitinous organic matrix, these structures display several effective lines of defense against catastrophic failure during repetitive high energy loading events. The study of this organism and its relatives has lead to design cues, which were incorporated into prototype composite materials designed for applications in aviation, body armor, and entertainment.

  1. Blast and Impact Resistant Composite Structures for Navy Ships

    Science.gov (United States)

    2013-03-15

    Kinetic Energy of flying particles Beginning with the pioneering work by Mandelbrot et al. [1], numerous investigators have focused on statistical...affine [10]. Self affinity is defined and well-described in the context of fractals by Mandelbrot [2]. As the crack propagates, the scale of...manufactured by Larry Drzal’s group at Michigan State University—Composite Materials and Structures Center. References 1. Mandelbrot , B.B.; Passoja

  2. Premixes production for synthesis of wear-resistant composite materials

    Science.gov (United States)

    Kontsevoi, Yu V.; Meilakh, A. G.; Shubin, A. B.; Pastukhov, E. A.; Dolmatov, A. V.; Sipatov, I. S.

    2017-01-01

    State of the art line of powder metallurgy is application of initial powders as micro-composites with additional components - premixes. Usage of premixes inhibits segregation of added components and implies the homogeneity of powder charge composition, and finally it has a significant impact on structure formation and properties of end products. The aim of the present work was to design the new production technology of premixes based on iron powder which is layer-by-layer plated by aluminium and copper. We propose to carry out production of Cu-Al-Fe premixes in two stages: cladding of iron powder by aluminium and coating of the obtained composite by copper. The self-developed technique of vibration treatment of iron and aluminium powder mixture was chosen for this purpose. The uniform in thickness and unbroken copper-plating of Fe-Al powders were carried out by chemical technique. Physico-chemical properties and production conditions of premixes-powders were studied, besides optimal parameters of production and further heat-treatment were selected. In the result of the present study the Fe-Al-Cu premixes with laminated structure comprising of iron core, Fe-Al and Cu-Al intermetallide shells were synthesised.

  3. Electrical resistance of CNT-PEEK composites under compression at different temperatures

    Directory of Open Access Journals (Sweden)

    Mohiuddin Mohammad

    2011-01-01

    Full Text Available Abstract Electrically conductive polymers reinforced with carbon nanotubes (CNTs have generated a great deal of scientific and industrial interest in the last few years. Advanced thermoplastic composites made of three different weight percentages (8%, 9%, and 10% of multiwalled CNTs and polyether ether ketone (PEEK were prepared by shear mixing process. The temperature- and pressure-dependent electrical resistance of these CNT-PEEK composites have been studied and presented in this paper. It has been found that electrical resistance decreases significantly with the application of heat and pressure.

  4. The microstructural aspects of abrasive wear resistance in composite electron beam clad coatings

    Science.gov (United States)

    Gnyusov, S. F.; Tarasov, S. Yu.

    2014-02-01

    The effect of microstructure and phase composition of composite coatings based on manganese-containing or nickel-containing austenitic steel and containing either 10 wt.% TiC or 15 wt.% WC on the abrasive wear resistance has been studied. Both post-deposition heat treatment and self-aging in the course of deposition served to improve the relative wear resistance coefficient by 38-42 and 5-12% for Fe-20%Mn-4%V-4%Mo + 15%WC and Fe-20%Ni-4%V-4%Mo + 15%WC coatings, respectively.

  5. Preparation and corrosion resistance of MAO/Ni-P composite coat on Mg alloy

    Science.gov (United States)

    Fan, Xizhi; Wang, Ying; Zou, Binglin; Gu, Lijian; Huang, Wenzhi; Cao, Xueqiang

    2013-07-01

    Microarc oxidation (MAO) coat was designed as an intermediate layer for the electroless plated Ni-P top coat, providing inert surface and necessary hardness for Mg alloy substrate. The composite coat was successfully prepared to improve the corrosion resistance of Mg alloy. The preparation and the characterization of the composite coat were investigated. The results show that the pre-treatment of MAO before electroless plating plays an important role in the deposition of compact composite coat. The activation (by HF solution) makes the MAO coat dense with uniform cracks which supply excellent bonding interface for Ni-P coat. Compared with monolithic MAO or Ni-P coat, the composite coat has excellent corrosion resistance and stable bonding interface. There is main pit corrosion at substrate after the corrosive medium penetrating through the whole coat. With the inert MAO interlayer, the electrochemical corrosion between the Ni-P and substrate is effectively inhibited.

  6. Carbon fiber polymer-matrix structural composites for electrical-resistance-based sensing

    Science.gov (United States)

    Wang, Daojun

    This dissertation has advanced the science and technology of electrical-resistance-based sensing of strain/stress and damage using continuous carbon fiber epoxy-matrix composites, which are widely used for aircraft structures. In particular, it has extended the technology of self-sensing of carbon fiber polymer-matrix composites from uniaxial longitudinal loading and flexural loading to uniaxial through-thickness loading and has extended the technology from structural composite self-sensing to the use of the composite (specifically a one-lamina composite) as an attached sensor. Through-thickness compression is encountered in the joining of composite components by fastening. Uniaxial through-thickness compression results in strain-induced reversible decreases in the through-thickness and longitudinal volume resistivities, due to increase in the fiber-fiber contact in the through-thickness direction, and minor-damage-induced irreversible changes in these resistivities. The Poisson effect plays a minor role. The effects in the longitudinal resistivity are small compared to those in the through-thickness direction, but longitudinal resistance measurement is more amenable to practical implementation in structures than through-thickness resistance measurement. The irreversible effects are associated with an increase in the through-thickness resistivity and a decrease in the longitudinal resistivity. The through-thickness gage factor is up to 5.1 and decreases with increasing compressive strain above 0.2%. The reversible fractional change in through-thickness resistivity per through-thickness strain is up to 4.0 and decreases with increasing compressive strain. The irreversible fractional change in through-thickness resistivity per unit through-thickness strain is around -1.1 and is independent of the strain. The sensing is feasible by measuring the resistance away from the stressed region, though the effectiveness is less than that at the stressed region. A one

  7. Slab detachment during continental collision: Influence of crustal rheology and interaction with lithospheric delamination

    Science.gov (United States)

    Duretz, T.; Gerya, T. V.

    2013-08-01

    Collision between continents can lead to the subduction of continental material. If the crust remains coupled to the downgoing slab, a large buoyancy force is generated. This force slows down convergence and promotes slab detachment. If the crust resists to subduction, it may decouple from the downgoing slab and be subjected to buoyant extrusion. We employ two-dimensional thermo-mechanical modelling to study the importance of crustal rheology on the evolution of subduction-collision systems. We propose simple quantifications of the mechanical decoupling between lithospheric levels (σ*) and the potential for buoyant extrusion of the crust (ξ*). The modelling results indicate that a variable crustal rheological structure results in slab detachment, delamination, or the combination of both mechanisms. A strong crust provides coupling at the Moho (low σ*) and remains coherent during subduction (low ξ). It promotes deep subduction of the crust (180 km) and slab detachment. Exhumation occurs in coherent manners via eduction and thrusting. Slab detachment triggers the development of topography (> 4.5 km) close to the suture. A contrasting style of collision occurs using a weak crustal rheology. Mechanical decoupling at the Moho (high σ*) promotes the extrusion of the crust (high ξ), disabling slab detachment. Ongoing shortening leads to buckling of the crust and development of topography on the lower plate. Collisions involving rheologically layered crust allow decoupling at mid-crustal depths. This structure favours both the extrusion of upper crust and the subduction of the lower crust. Such collisions are successively affected by delamination and slab detachment. Topography develops together with the buoyant extrusion of crust onto the foreland and is further amplified by slab detachment. Our results suggest that the occurrence of both delamination (Apennines) and slab detachment (Himalayas) in orogens may indicate differences in the initial crustal structure of

  8. Preparation of electrodes on cfrp composites with low contact resistance comprising laser-based surface pre-treatment

    KAUST Repository

    Almuhammadi, Khaled Hamdan

    2016-12-29

    Various examples are provided related to the preparation of electrodes on carbon fiber reinforced polymer (CFRP) composites with low contact resistance. Laser-based surface preparation can be used for bonding to CFRP composites. In one example, a method includes preparing a pretreated target area on a CFRP composite surface using laser pulsed irradiation and bonding an electrode to exposed fibers in the pretreated target area. The surface preparation can allow the electrode to have a low contact resistance with the CFRP composite.

  9. Mullite-zirconium composites reinforced with ceramic fibres resistant to 1450 C; obtaining and properties

    Energy Technology Data Exchange (ETDEWEB)

    Cerchez, L.; Constantinescu, S. [PROCEMA S.A. Bucharest - Research, Design and Experimental Production, Bucharest (Romania). Inst. for Construction and Construction Materials; Muntean, M. [Universitatea Politehnica, Bucharest (Romania). Faculty of Industrial Chemistry

    2002-07-01

    The purpose of this paper was the obtaining of some mullite-zirconium matrix composites, reinforced with ceramic fibres resistant to 1450 C. In order to establish the compositions, the raw materials were ground, depending on their nature, in many ways, and there were established the characteristics of ground resulted powders. On the obtained materials it was followed the evolution of the ceramic, mechanical and structural characteristics, depending on the heat treatment temperature, for various reinforcing coefficients. (orig.)

  10. Collision-resistant hash function based on composition of functions

    CERN Document Server

    Ndoundam, Rene

    2011-01-01

    cryptographic hash function is a deterministic procedure that compresses an arbitrary block of numerical data and returns a fixed-size bit string. There exist many hash functions: MD5, HAVAL, SHA, ... It was reported that these hash functions are not longer secure. Our work is focused in the construction of a new hash function based on composition of functions. The construction used the NP-completeness of Three-dimensional contingency tables and the relaxation of the constraint that a hash function should also be a compression function.

  11. Ablation Resistance of C/C Composites with Atmospheric Plasma-Sprayed W Coating

    Science.gov (United States)

    Zhou, Zhe; Wang, Yuan; Gong, Jieming; Ge, Yicheng; Peng, Ke; Ran, Liping; Yi, Maozhong

    2016-12-01

    To improve the ablation resistance of carbon/carbon (C/C) composites, tungsten (W) coating with thickness of 1.2 mm was applied by atmospheric plasma spraying. The antiablation property of the coated composites was evaluated by oxyacetylene flame ablation experiments. The phase composition of the coating was investigated by a combination of x-ray diffraction analysis and scanning electron microscopy with energy-dispersive x-ray spectroscopy analysis. The ablation resistance of the coated C/C substrates was compared with that of uncoated C/C composites and C/C-CuZr composites after ablation for 30 s. The properties of the coated C/C composites after ablation time of 10, 30, 60, 90, 120, and 180 s were further studied. The results indicated that the mass and linear ablation rates of the W-coated C/C composites were lower than those of uncoated C/C or C/C-CuZr composites after ablation for 30 s. The coating exhibited heat stability after 120 s of ablation, with mass loss and linear ablation rates of 7.39 × 10-3 g/s and 3.50 × 10-3 mm/s, respectively. However, the W coating became ineffective and failed after ablation for 180 s. Three ablation regions could be identified, in which the ablation mechanism of the coating changed from thermochemical to thermophysical erosion to mechanical scouring with increasing ablation time.

  12. Microstructure and wear resistance of in situ porous TiO/Cu composites

    Science.gov (United States)

    Qin, Qingdong; Huang, Bowei; Li, Wei

    2016-07-01

    An in situ porous TiO/Cu composite is successfully prepared using powder metallurgy by the reaction of Ti2CO and Cu powder. Morphological examination of the composite shows that the porosity of composites lies in the range between 10.2% and 35.2%. Dry sliding un-lubricated wear tests show that the wear resistance of the composite is higher than that of the Cu-Al alloy ingot. The coefficient of friction test shows that, as the volume fraction of the reinforced phase increases, the coefficient of friction decreases. The wear rate variation trend of the oil-lubricated wear test results is similar to that of the un-lubricated wear test results. The coefficient of friction for oil lubrication is similar for different volume fractions of the reinforced phase. The wear resistance of the composite at a sliding velocity of 200 rpm is slightly larger than that at 50 rpm. The porosity of the composites enhances the high-velocity oil-lubricated sliding wear resistance.

  13. Adhesion of polymer coatings studied by laser-induced delamination

    NARCIS (Netherlands)

    Fedorov, A; De Hosson, JTM

    2005-01-01

    This paper concentrates on the laser-induced delamination technique, aimed at measuring the practical work of adhesion of thin polymer coatings on metal substrates. In this technique an infrared laser-pulsed beam is used to create an initial blister. Upon increasing the pulse intensity, the size of

  14. Simulation of cusp formation in mode II delamination

    NARCIS (Netherlands)

    Sluys, L.J.; Van der Meer, F.P.

    2014-01-01

    On the microlevel, cusps are formed during delamination crack growth under mode II loading conditions. In this work, two different approaches to simulate this process are presented. Firstly a cohesive zone method where cohesive segments are introduced between a pair of neighbouring elements when the

  15. Modeling delamination due to thermal stress in optical storage media

    Science.gov (United States)

    Nkansah, M. A.; Evans, K. E.

    1990-04-01

    Finite element analysis is used to calculate the shape of blisters formed in bilayer optical storage media due to the buildup of thermal stresses during laser writing. It is shown that practically usable blisters may be expected to form in a time period of about 15 ns. Such a thermal stress delamination process may also precede melting in conventional pit formation processes.

  16. Ets-1 confers cranial features on neural crest delamination.

    Directory of Open Access Journals (Sweden)

    Eric Théveneau

    Full Text Available Neural crest cells (NCC have the particularity to invade the environment where they differentiate after separation from the neuroepithelium. This process, called delamination, is strikingly different between cranial and trunk NCCs. If signalings controlling slow trunk delamination start being deciphered, mechanisms leading to massive and rapid cranial outflow are poorly documented. Here, we show that the chick cranial NCCs delamination is the result of two events: a substantial cell mobilization and an epithelium to mesenchyme transition (EMT. We demonstrate that ets-1, a transcription factor specifically expressed in cranial NCCs, is responsible for the former event by recruiting massively cranial premigratory NCCs independently of the S-phase of the cell cycle and by leading the gathered cells to straddle the basal lamina. However, it does not promote the EMT process alone but can cooperate with snail-2 (previously called slug to this event. Altogether, these data lead us to propose that ets-1 plays a pivotal role in conferring specific cephalic characteristics on NCC delamination.

  17. Webbing and Delamination of Drug Eluting Stent Coatings.

    Science.gov (United States)

    Hopkins, C; Sweeney, C A; O'Connor, C; McHugh, P E; McGarry, J P

    2016-02-01

    The advancement of the drug-eluting stent technology raises the significant challenge of safe mechanical design of polymer coated stent systems. Experimental images of stent coatings undergoing significant damage during deployment have been reported; such coating damage and delamination can lead to complications such as restenosis and increased thrombogenicity. In the current study a cohesive zone modeling framework is developed to predict coating delamination and buckling due to hinge deformation during stent deployment. Models are then extended to analyze, for the first time, stent-coating damage due to webbing defects. Webbing defects occur when a bond forms between coating layers on adjacent struts, resulting in extensive delamination of the coating from the strut surfaces. The analyzes presented in this paper uncover the mechanical factors that govern webbing induced coating damage. Finally, an experimental fracture test of a commercially available stent coating material is performed and results demonstrate that the high cohesive strength of the coating material will prevent web fracture, resulting in significant coating delamination during stent deployment.

  18. Modeling the buckling and delamination of thin films

    Science.gov (United States)

    Jagla, E. A.

    2007-02-01

    I study numerically the problem of delamination of a thin film elastically attached to a rigid substrate. A nominally flat elastic thin film is modeled using a two-dimensional triangular mesh. Both compression and bending rigidities are included to simulate compression and bending of the film. The film can buckle (i.e., abandon its flat configuration) when enough compressive strain is applied. The buckled configurations of a piece of film with stripe geometry are investigated as a function of the compressive strain. It is found that the stable configuration depends strongly on the applied strain and the Poisson ratio of the film. Next, the film is considered to be attached to a rigid substrate by springs that can break when the detaching force exceeds a threshold value, producing partial delamination of the film. Delamination is induced by a mismatch of the relaxed configurations of film and substrate. The morphology of the delaminated film can be followed and compared with available experimental results as a function of model parameters. “Telephone-cord,” polygonal, and “brainlike” patterns qualitatively similar to experimentally observed configurations are obtained in different parameter regions. The main control parameters that select the different patterns are the strain mismatch between film and substrate and the degree of in-plane relaxation within the unbuckled regions.

  19. Influence of surface pretreatment of fiber posts on cement delamination

    NARCIS (Netherlands)

    Jongsma, L.A.; Kleverlaan, C.J.; Feilzer, A.J.

    2010-01-01

    Objectives To evaluate the influence of post surface pretreatment on the delamination strength of different cements from a prefabricated FRC post tested in a three-point bending test. Methods Three cements were tested; RelyX Unicem, DC Core Automix, and Panavia F2.0. Per cement, 40 posts (D.T. Light

  20. Impact Delamination and Fracture in Aluminum/Acrylic Sandwich Plates

    Science.gov (United States)

    Liaw, Benjamin; Zeichner, Glenn; Liu, Yanxiong; Bowles, Kenneth J. (Technical Monitor)

    2000-01-01

    Impact-induced delamination and fracture in 6061-T6 aluminum/cast acrylic sandwich plates adhered by epoxy were generated in an instrumented drop-weight impact machine. Although only a small dent was produced on the aluminum side when a hemispherical penetrator tup was dropped onto it from a couple of inches, a large ring of delamination at the interface was observed. The delamination damage was often accompanied by severe shattering in the acrylic substratum. Damage patterns in the acrylic layer include radial and ring cracks and, together with delamination at the interface, may cause peeling-off of acrylic material from the sandwich plate. Theory of stress-wave propagation can be used to explain these damage patterns. The impact tests were conducted at various temperatures. The results also show clearly that temperature effect is very important in impact damage. For pure cast acrylic nil-ductile transition (NDT) occurs between 185-195 F. Excessive impact energy was dissipated into fracture energy when tested at temperature below this range or through plastic deformation when tested at temperature above the NDT temperature. Results from this study will be used as baseline data for studying fiber-metal laminates, such as GLARE and ARALL for advanced aeronautical and astronautical applications.

  1. Modelling the influence of steel fibres on the electrical resistivity of cementitious composites

    DEFF Research Database (Denmark)

    Solgaard, Anders Ole Stubbe; Michel, Alexander; Stang, Henrik

    2009-01-01

    work concerns the electrical resistivity of cementitious composites and some of the parameters influencing it in order to get a more thorough understanding of the factors governing the overall resistivity. The basis of the present study is an experimental investigation of the electrical resistivity...... the overall resistivity of the material and thereby the corrosion rate of the embedded reinforcement. To the knowledge of the authors, only preliminary studies have been made on the influence of corrosion of the reinforcement bars from the addition of the electrical conductive steel fibres. Thus the present......One of the governing factors on the corrosion of embedded reinforcement is the electrical resistivity of the concrete. The combination of steel fibres and conventional reinforcement bars has been used in a number of structures. However, the addition of electrical con-ductive fibres might influence...

  2. Synthesis of mullite nanometers microwave from bentonite delaminated; Sintese de mulita nanometrica por microondas a partir bentonitas delaminadas

    Energy Technology Data Exchange (ETDEWEB)

    Gomes, J.; Azevedo, N.A.; Vieira, D.A.; Neves, G.A.; Santana, L.N.L., E-mail: josileido@yahoo.com.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Menezes, R.R. [Universidade Federal da Paraiba (UFPB), PB (Brazil)

    2011-07-01

    The smectite clays present as lamellar structure is formed by two layers of silica tetrahedrons and one layer of aluminum octahedra, which can be individually delaminated, reaching a thickness of about 1mm. Mullite is the only thermodynamically stable crystalline phase of SiO{sub 2} and Al2O{sub 3} system and can be synthesized from minerals that exhibit these oxides in its composition. The microwave synthesis offers advantages over conventional methods, the heating is rapid and uniform, avoiding an undesirable grain growth. This study aims to obtain nanometric mullite from bentonites delamined subjected to microwave heating. The samples were initially treated, then rehydrated, frozen and deagglomeration in a ball mill for 4 and 8 hours. Subsequently subjected to centrifugation, drying and microwave heating. The results showed that nano-mullite was obtained for samples subjected to longer heating and dispersions. (author)

  3. Clinical evaluation of a highly wear resistant composite.

    Science.gov (United States)

    Dickinson, G L; Gerbo, L R; Leinfelder, K F

    1993-04-01

    The purpose of this clinical study was to determine the long-term potential of a resin composite restorative material. A total of 62 restorations of a modified Herculite Incisal formulation were inserted into Class I and Class II preparations. A control group of the conventional Herculite formulation was also placed into Class I and Class II cavity preparations at an earlier date. The cavity preparations for both formulations were standardized to conform to that of conventional conservative amalgams. Deep portions of the preparations were lined with calcium hydroxide. The enamel margins were etched per manufacturers' directions followed by a dentin bonding agent. After application of the appropriate matrix, the restorations were placed incrementally. Each restoration was independently evaluated by two clinicians at baseline, 6-months, 1, 2 and 3 years in accordance with the USPHS criteria. In addition, all restorations were evaluated for wear using a series of optical standards (M-L). The color matching ability of the material never fell below 96%. The percent of restorations exhibiting a surface texture similar to enamel never fell below 90% Alfa. At the end of 3 years, the total average loss of material was only 28 microns. No clinical evidence of bulk fracture was detected with the modified Herculite formulation at 3 years. The wear rate of the modified formulation of Herculite was essentially one-half that of conventional Herculite XR. Marginal ditching, which is characteristic of most posterior resin composites in which the filler particle is 1 micron or less, was exhibited.(ABSTRACT TRUNCATED AT 250 WORDS)

  4. Epoxy Resin/Nano Ni@C Composites Exhibiting NTC Effect with Tunable Resistivity

    Institute of Scientific and Technical Information of China (English)

    Bangwen Zhang; Baowei Li; Changsheng Xie

    2009-01-01

    Epoxy resin/Ni@C nanoparticle composites with aligned microstructure were prepared by using a procedure of magnetic field assisted curing. The results show that the resistivity of composites exhibits negative temperature coefficient (NTC) effect above room temperature, and can be adjusted by varying the content filler and the magnitude of magnetic field applied. Hill's quantum tunneling model was modified to understand the electrical conduction mechanism in the composites. It shows that the NTC effect ascribes to the dominant thermal activated tunneling transport of electron across adjacent nanoparticles, as well as the low thermal expansivity of epoxy resin matrix.

  5. In Vitro Fatigue Resistance of Teeth Restored With Bulk Fill versus Conventional Composite Resin.

    Science.gov (United States)

    Rauber, Gabrielle Branco; Bernardon, Jussara Karina; Vieira, Luiz Clovis Cardoso; Maia, Hamilton Pires; Horn, Françoá; Roesler, Carlos Rodrigo de Mello

    2016-01-01

    The aim of this study was to compare the fatigue resistance of restored teeth with bulk fill composite resin, conventional composite resin with incremental insertion and unprepared sound teeth. Twenty-eight extracted maxillary premolars were selected and divided into 4 groups based on composite resin and insertion technique: control (C), conventional composite resin with incremental insertion (I) and bulk fill composite resin with three (BF3) or single increment (BF1). The restored specimens were submitted to fatigue resistance test with a 5 Hz frequency. An initial application of 5,000 sinusoidal load cycles with a minimum force of 50 N and a maximum force of 200 N was used. Next, were applied stages of 30,000 load cycles with the maximum force increasing gradually: 400, 600, 800, 1000, 1200 and 1400 N. The test was concluded when 185,000 load cycles were achieved or the specimen failed. The fatigue resistance data were recorded for comparison, using the Kaplan-Meier survival curve and analyzed by log-rank test at 0.05 significance. Fractures were classified based on the position of the failure - above or below the cementoenamel junction (CEJ). Statistical analysis of the Kaplan-Meier survival curve and log-rank test showed a significant difference between groups (p=0.001). The fracture analysis demonstrated that only 28.58% of failures were below the CEJ in group C, while for groups I, BF1 and BF3 they were 42.85%, 85.71% and 85.71%, respectively. Teeth restored with composite bulk fill in both techniques present similar fatigue resistance values compared with those restored with a conventional incremental insertion of composite, while the fatigue strength values of unprepared sound teeth were higher. Furthermore, unprepared sound teeth showed a lower percentage of fractures below the CEJ.

  6. Insulin resistance, inflammation, and serum fatty acid composition.

    Science.gov (United States)

    Fernández-Real, José-Manuel; Broch, Montserrat; Vendrell, Joan; Ricart, Wifredo

    2003-05-01

    Fatty acids (FAs) have been involved in the development of chronic inflammatory conditions such as insulin resistance and obesity. However, the relation among insulin resistance, obesity, inflammatory activity (circulating interleukin [IL]-6) and dietary FAs has been scarcely studied in otherwise healthy subjects. We aimed to study these interactions in 123 overweight (BMI 26.9 +/- 2.4 kg/m(2) [means +/- SD]) subjects and 109 lean (BMI 21.7 +/- 1.7 kg/m(2), P cromatography. The percentage of saturated FAs (r = 0.30, P = 0.01) and omega-6 FAs (r = -0.32, P = 0.001) were significantly associated with circulating IL-6, whereas the percentage of omega-3 FAs correlated negatively with C-reactive protein in overweight subjects (P = 0.04). Saturated-to-omega-3 and saturated-to-omega-6 FA ratios were significantly and positively associated with C-reactive protein (P < 0.0001) and IL-6 (P < 0.001), respectively. In contrast, none of these associations reached statistical significance in lean subjects. Those subjects in the most insulin-sensitive quintile (homeostasis model assessment value) showed a significantly higher percentage of linoleic acid (C18:2 varpi6) (P = 0.03) and a significantly lower level of araquidic (C20:0) (P = 0.04), behenic (C22:0) (P = 0.009), lignoceric (C24:0) (P = 0.02), and nervonic (C24:1 varpi9) (P = 0.001) FAs than the remaining subjects. In parallel, the most insulin-sensitive subjects showed significantly decreased C-reactive protein (P = 0.03). Serum C-reactive protein was significantly associated with percent linoleic acid and eicosapentaenoic acid in nonsmoking men (P = 0.03 and P = 0.04, respectively) and with docosahexaenoic acid in nonsmoking women (r = -0.46, P < 0.0001). We constructed a multivariant regression analysis to predict circulating IL-6. Age, BMI, waist-to-hip ratio (WHR), smoking status, and the relation of saturated to omega-6 or saturated to omega-3 FAs were considered as independent variables separately in men and women

  7. Biodiversity increases functional and compositional resistance, but decreases resilience in phytoplankton communities.

    Science.gov (United States)

    Baert, Jan M; De Laender, Frederik; Sabbe, Koen; Janssen, Colin R

    2016-12-01

    There is now ample evidence that biodiversity stabilizes aggregated ecosystem functions, such as primary production, in changing environments. In primary producer systems, this stabilizing effect is found to be driven by higher functional resistance (i.e., reduced changes in functions by environmental changes) rather than through higher functional resilience (i.e., rapid recovery following environmental changes) in more diverse systems. The stability of aggregated ecosystem functions directly depends on changes in species composition and by consequence their functional contributions to ecosystem functions. Still, it remains only theoretically explored how biodiversity can stabilize ecosystem functions by affecting compositional stability. Here, we demonstrate how biodiversity effects on compositional stability drive biodiversity effects on functional stability in diatom communities. In a microcosm experiment, we exposed 39 communities of five different levels of species richness (1, 2, 4, 6, and 8 species) to three concentrations of a chemical stressor (0, 25, and 250 μg/L atrazine) for four weeks, after which all communities were transferred to atrazine-free medium for three more weeks. Biodiversity simultaneously increased, increasing functional and compositional resistance, but decreased functional and compositional resilience. These results confirm the theoretically proposed link between biodiversity effects on functional and compositional stability in primary producer systems, and provide a mechanistic underpinning for observed biodiversity-stability relationships. Finally, we discuss how higher compositional stability can be expected to become increasingly important in stabilizing ecosystem functions under field conditions when multiple environmental stressors fluctuate simultaneously. © 2016 by the Ecological Society of America.

  8. Enhanced Strain-Dependent Electrical Resistance of Polyurethane Composites with Embedded Oxidized Multiwalled Carbon Nanotube Networks

    Directory of Open Access Journals (Sweden)

    R. Benlikaya

    2013-01-01

    Full Text Available The effect of different chemical oxidation of multiwalled carbon nanotubes with H2O2, HNO3, and KMnO4 on the change of electrical resistance of polyurethane composites with embedded oxidized nanotube networks subjected to elongation and bending has been studied. The testing has shown about twenty-fold increase in the electrical resistance for the composite prepared from KMnO4 oxidized nanotubes in comparison to the composites prepared from the pristine and other oxidized nanotubes. The evaluated sensitivity of KMnO4 treated composite in terms of the gauge factor increases with strain to nearly 175 at the strain 11%. This is a substantial increase, which ranks the composite prepared from KMnO4 oxidized nanotubes among materials as strain gauges with the highest electromechanical sensitivity. The observed differences in electromechanical properties of the composites are discussed on basis of their structure which is examined by the measurements of Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscope. The possible practical use of the composites is demonstrated by monitoring of elbow joint flexion during two different physical exercises.

  9. Decay resistance of wood-plastic composites reinforced with extracted or delignified wood flour

    Science.gov (United States)

    Rebecca E. Ibach; Yao Chen; Nicole M. Stark; Mandla A. Tshabalala; Yongming Fan; Jianmin Gao

    2014-01-01

    The moisture and decay resistance of wood-plastic composites (WPCs) reinforced with extracted or delignified wood flour (WF) was investigated. Three different extractions were preformed: toluene/ethanol (TE), acetone/water (AW), and hot water (HW). Delignification (DL) was performed using a sodium chlorite/acetic acid solution. All WPCs specimens were made with 50% by...

  10. Oxidation resistant coating for titanium alloys and titanium alloy matrix composites

    Science.gov (United States)

    Brindley, William J. (Inventor); Smialek, James L. (Inventor); Rouge, Carl J. (Inventor)

    1992-01-01

    An oxidation resistant coating for titanium alloys and titanium alloy matrix composites comprises an MCrAlX material. M is a metal selected from nickel, cobalt, and iron. X is an active element selected from Y, Yb, Zr, and Hf.

  11. In vitro fracture resistance of fiber reinforced cusp-replacing composite restorations.

    NARCIS (Netherlands)

    Fennis, W.M.M.; Tezvergil, A.; Kuijs, R.H.; Lassila, L.V.; Kreulen, C.M.; Creugers, N.H.J.; Vallittu, P.K.

    2005-01-01

    OBJECTIVES: To assess the fracture resistance and failure mode of fiber reinforced composite (FRC) cusp-replacing restorations in premolars. METHODS: Forty-five extracted sound upper premolars were randomly divided into three groups. Identical MOD cavities with simulated buccal cusp fracture and hei

  12. In vitro fracture resistance of fiber reinforced cusp-replacing composite restorations.

    NARCIS (Netherlands)

    Fennis, W.M.M.; Tezvergil, A.; Kuijs, R.H.; Lassila, L.V.; Kreulen, C.M.; Creugers, N.H.J.; Vallittu, P.K.

    2005-01-01

    OBJECTIVES: To assess the fracture resistance and failure mode of fiber reinforced composite (FRC) cusp-replacing restorations in premolars. METHODS: Forty-five extracted sound upper premolars were randomly divided into three groups. Identical MOD cavities with simulated buccal cusp fracture and hei

  13. A study of process induced voids in resistance welding of thermoplastic composites

    NARCIS (Netherlands)

    Shi, H.; Fernandez Villegas, I.; Bersee, H.E.N.

    2015-01-01

    Void formation in resistance welding of woven fabric reinforced thermoplastic composites was investigated. Void contents were measured using optical microscopy and digital image process. Un-even void distributions were observed in the joints, and more voids were found in the middle of the joints tha

  14. Study of the relation between hydrated portland cement composition and leaching resistance

    NARCIS (Netherlands)

    Eijk, van R.J.; Brouwers, H.J.H.

    1998-01-01

    The present paper addresses cement compositions that have an optimal resistance against acid attack and hence, low leaching rates and optimal waste containment. To this end a shrinking core leaching model is used that describes the leaching of metals from a cement sample. This process is directly re

  15. Characterization of fatigue resistance in photochromic composite materials for 3D rewritable optical memory applications

    Energy Technology Data Exchange (ETDEWEB)

    Samoylova, Elena, E-mail: Elena.Samoylova@physik.uni-muenchen.de [Nanophysics, Istituto Italiano di Tecnologia, via Morego 30, 16163 Genova (Italy); Dallari, William; Allione, Marco; Pignatelli, Francesca; Marini, Lara; Cingolani, Roberto; Diaspro, Alberto [Nanophysics, Istituto Italiano di Tecnologia, via Morego 30, 16163 Genova (Italy); Athanassiou, Athanassia, E-mail: athanassia.athanassiou@iit.it [Nanophysics, Istituto Italiano di Tecnologia, via Morego 30, 16163 Genova (Italy); Center for Biomolecular Nanotechnologies-Unile, Istituto Italiano di Tecnologia, via Barsanti, 73010 Arnesano, Lecce (Italy)

    2013-06-01

    Highlights: • Fatigue resistance of diarylethene–polymer composites was tested with optical absorption and fluorescence methods upon repetitive UV–VIS irradiation. • Significant differences in fatigue were found in different polymeric matrices and in one-photon and two-photon excitation experiments. • Several explanations for fatigue resistance of the composites are proposed based on the physico-chemical properties of the diarylethenes and polymeric matrices. -- Abstract: Fatigue resistance of the photochromic diarylethene molecules 1,2-bis[2-methylbenzo[b]thyophen-3-yl] -3,3,4,4,5,5-hexafluoro-1-cyclopentene embedded in three different acrylic polymers is studied upon multiple coloration–decoloration cycles. The resistance to photofatigue is found to be different in the three polymeric materials when one-photon excitation was used for the reversible photoconversion experiment. In particular, the photochromic molecules lose their photoisomerization ability faster if they are embedded in poly(methyl methacrylate) (PMMA) with respect to poly(ethyl methacrylate-co-methyl acrylate) (PEMMA) and poly(ethyl methacrylate) (PEMA). We propose several explanations based on the physico-chemical properties of the matrix and of the photochromic molecules. In the case of two-photon excitation, which is necessary for 3D optical writing, the fatigue resistance is found to be poorer than in the one-photon case. The accelerated photodegradation can be assigned to the non-linear nature of interaction between the polymeric composite material and light.

  16. "A New Class of Creep Resistant Oxide/Oxide Ceramic Matrix Composites"

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Mohit Jain, Dr. Ganesh Skandan, Prof. Roger Cannon, Rutgers University

    2007-03-30

    Despite recent progress in the development of SiC-SiC ceramic matrix composites (CMCs), their application in industrial gas turbines for distributed energy (DE) systems has been limited. The poor oxidation resistance of the non-oxide ceramics warrants the use of envrionmental barrier coatings (EBCs), which in turn lead to issues pertaining to life expectancy of the coatings. On the other hand, oxide/oxide CMCs are potential replacements, but their use has been limited until now due to the poor creep resistance at high temperatures, particularly above 1200 oC: the lack of a creep resistant matrix has been a major limiting factor. Using yttrium aluminum garnet (YAG) as the matrix material system, we have advanced the state-of-the-art in oxide/oxide CMCs by introducing innovations in both the structure and composition of the matrix material, thereby leading to high temperature matrix creep properties not achieved until now. An array of YAG-based powders with a unique set of particle characteristics were produced in-house and sintered to full density and compressive creep data was obtained. Aided in part by the composition and the microstructure, the creep rates were found to be two orders of magnitude smaller than the most creep resistant oxide fiber available commercially. Even after accounting for porosity and a smaller matrix grain size in a practical CMC component, the YAG-based matrix material was found to creep slower than the most creep resistant oxide fiber available commercially.

  17. Termovision and electricity capacitance measurements as a evaluation of a helicopter rotor’s blades delamination

    Directory of Open Access Journals (Sweden)

    Gębura Andrzej

    2015-12-01

    Full Text Available The article presents essential elements reached during investigations of heat section of rotor blades which have been done in AFIT. The investigations were related to a valuation of helicopter’s rotor blades delamination. They used a method of thermal field measurement as well as a electricity capacitance between an airframe and a heat element of the installation. A suggestion of such measurements appeared during the disassembly of rotor blade heat sections when some local unglue of heat element’s tape from the structure of blade’s heating pack has seen. Spots nearby separation of adhesive are a potential area of a local temperature increase, both the electric heating element and the mechanical structure of the blade. This is especially dangerous for composite structures. Overheated composite structures characterized by reduced flexibility and becomes prone to cracking. Therefore, the possibility of non-invasive monitoring adhesive spots, without removing the blades would be particularly useful.

  18. Characterization of microstructure and properties of Al–Al$_3$Zr–Al$_2$O$_3$ composite

    Indian Academy of Sciences (India)

    ANUP MANDAL; KARABI DAS; SIDDHARTHA DAS

    2016-08-01

    Aluminium-based metal matrix composite strengthened by in situ Al$_2$O$_3$ and Al$_3$Zr particles were synthesized by powder metallurgy route. Phase analysis by X-ray diffraction and scanning electronmicroscopy revealed that the reaction between Al and ZrO$_2$ produced Al$_2$O$_3$ and Al$_3$Zr phases in the sintered composites. The hardness of the composite is a strong function of sintering temperature as well as the volume fraction of reinforcements. The dry sliding wear test results clearly indicated that increasing the volume fraction of zirconia particles in the compositeimproved the wear resistance. Microcutting, ploughing, delamination and oxidation were the main mechanisms of wear.

  19. Preparation and wear resistance of Ti-Zr-Ni quasicrystal and polyamide composite materials

    Science.gov (United States)

    Wang, Xinlu; Li, Xuesong; Zhang, Zhenjiang; Zhang, Shanshan; Liu, Wanqiang; Wang, Limin

    2011-07-01

    Ti-Zr-Ni icosahedral quasicrystal powders (Ti-QC), prepared by mechanical alloying and then annealing in a vacuum furnace, were used as a novel filler material in polyamide 12 (PA12). The melt processability of the composite was studied using a Haake torque rheometer. This indicates that PA12/Ti-QC composites can be melt-processed into a wear-resistant material. Further, these composites, fabricated by compression molding, were tested in sliding wear against a polished bearing steel counterface. The results from wear testing show that the addition of Ti-QC filler to PA12 enhances wear resistance and reduces volume loss by half compared with neat PA12. Furthermore, it is found that the hardness of the composite increases with increasing content of Ti-QC filler. In addition, PA12/Ti-QC composites exhibit a slightly higher crystallization temperature and better thermal stability than PA12. These combined results demonstrate that Ti-QC filler may be a desirable alternative when attempting to increase the wear resistance of PA12.

  20. Resistance of Bonded Composite Restorations on Fractures of Endodontically Treated Teeth

    Directory of Open Access Journals (Sweden)

    AR Daneshkazemi

    2005-01-01

    Full Text Available Introduction: This study was performed to evaluate the effect of dentine bonding agents and Glass Ionomer cement beneath composite restorations and its resistance on fractures of endodontically treated teeth. Material and Methods: Forty sound maxillary teeth were selected; ten of them for positive control, and on the rest, RCT and MOD cavity preparations were done with standard methods. Then, the teeth were divided to four groups: 1-Sound teeth for positive control. 2-Prepared without any restoration for negative control. 3-Prepared and restored with Vitrabond(3M, USA, Single bond(3M, USA and Z100(3M, USA resin composite. 4-Prepared and restored by Single bond and Z100 resin composite. Specimens were subjected to compressive load by Instron 8502 until fracture occurred. Results: Group 1 showed the highest resistance to compressive forces followed by group 4,3&2 respectively. ANOVA, t test and Chi-square tests indicated significant difference between all the groups. Conclusion: Use of dentine bonding agents and resin composite increases resistance of endodontically treated teeth to fractures more than teeth restored with sandwich of glass ionomer cements, dentine bonding agents and resin composite.

  1. Glass delamination: a comparison of the inner surface performance of vials and pre-filled syringes.

    Science.gov (United States)

    Zhao, Jianxiu; Lavalley, Virginie; Mangiagalli, Paolo; Wright, Justin M; Bankston, Theresa E

    2014-12-01

    The occurrence of glass delamination is a serious concern for parenteral drug products. Over the past several years, there has been a series of product recalls involving glass delamination in parenteral drugs stored in vials which has led to heightened industry and regulatory scrutiny. In this study, a two-pronged approach was employed to assess the inner surface durability of vials and pre-filled syringes. Non-siliconized syringes were used in order to directly compare glass to glass performance between vials and syringes. The vial and syringe performance was screened with pharmaceutically relevant formulation conditions. The influence of pH, buffer type, ionic strength, and glass type and source was evaluated. In addition, an aggressive but discriminating formulation condition (glutaric acid, pH 11) was used to ascertain the impact of syringe processing. Advanced analytical tools including inductively coupled plasma/mass spectrometry, scanning electron microscopy, atomic force microscopy, and dynamic secondary ion mass spectroscopy showed significant differences in glass performance between vials and syringes. Pre-filled syringes outperform vials for most tests and conditions. The manufacturing conditions for vials lead to glass defects, not found in pre-filled syringes, which result in a less chemically resistant surface. The screening methodology presented in this work can be applied to assess suitability of primary containers for specific drug applications.

  2. High compressive resistance drainage geo composites; Geocompuestos de drenaje de alta resistencia a compresion

    Energy Technology Data Exchange (ETDEWEB)

    Castelo Nolla, J.; Gutierrez Cuevas, J.

    2014-02-01

    There are several typologies of drainage geo composites available in the market which can be classified according to their structures as: cus pated, mono filaments, geo nets and those products formed by the combination of a draining blanket with a series of mini-pipes. Each one of them has its own range of compressive resistances. There are applications, such as are the new cells of landfills or mines and roads or railways over large embankments, where the pressure exerted on the geo composite exceeds the compressive resistance of the majority of these typologies. For all this applications, besides providing and adequate flow capacity, it must be ensured that the chosen typology is able to withstand the required loading without collapsing and guaranteeing an adequate factor of safety. This article will expose that, currently, the only typology of drainage geo composites that can bear these loadings while maintaining its drainage properties is the tri-planar geo net. (Author)

  3. Wear Resistance of Deposited Layer Using Nickel-Based Composite Powders by Plasma-Arc Surfacing

    Institute of Scientific and Technical Information of China (English)

    DONG Li-hong; ZHU Sheng; XU Bin-shi; DU Ze-yu

    2004-01-01

    Nickel-based composite alloy powders were deposited on the surface of Q235 steel by plasma-arc surfacing in this work. Optimal proportions of elements intensifying the composite powders were ascertained by orthogonal design of three factors and three levels and orthogonal polynomial regression analysis , which Cr , Mn , W were 10% ,4% and 7 % respectively.Phase and structure of deposited materials were characterized by optical microscope and X- ray diffraction. Hardness tests and wear resistance tests were carried out to determine the performance of the deposited layers. The results show that the microstructure of deposited layers of composite powders mainly consist of γ-( Ni, Fe ) , γ- Ni, WC, W2 C, Mn31Si12, Cr23 C6,Cr7 C3, Cr, NiB, Ni2B etc. Wear resistance and hardness of the surface increased evidently.

  4. Structure and abrasive wear resistance of R6M5 steel-tungsten carbide composite coatings

    Science.gov (United States)

    Gnyusov, S. F.

    2012-09-01

    Features of the structure formation, composition, and abrasive wear resistance of R6M5 steel-tungsten carbide (R6M5-WC) composite coatings have been studied as dependent on the WC content. The introduction of ˜20 wt % WC into the hardening composition leads to an increase in the fraction of M6C carbide (in the form of eutectic inclusions with average size ˜5.9 μm at grain boundaries and dispersed ˜0.25 μm particles in the volume of grains), while a large proportion of metastable austenite (˜88 vol %) is still retained. The R6M5-WC coatings exhibit high abrasive wear resistance, which is ensured by the γ → α' martensite transformation during friction and a muiltimodal size distribution of hardening particles.

  5. Effect of Processing Conditions on Fracture Resistance and Cohesive Laws of Binderfree All-Cellulose Composites

    DEFF Research Database (Denmark)

    Goutianos, Stergios; Arévalo, R.; Sørensen, Bent F.

    2014-01-01

    microscope to a) perform accurate measurements of both the fracture energy for crack initiation and the fracture resistance and b) observe the microscale failure mechanisms especially in the the wake of the crack tip. Since the mechanical behaviour of the all-cellulose composites was non-linear, a general...... method was first developed to obtain fracture resistance values from the DCB specimens taking into account the non-linear material response. The binderfree all-cellulose composites were prepared by a mechanical refinement process that allows the formation of intramolecular bonds between the cellulose......The fracture properties of all-cellulose composites without matrix were studied using Double Cantilever Beam (DCB) sandwich specimens loaded with pure monotonically increasing bending moments, which give stable crack growth. The experiments were conducted in an environmental scanning electron...

  6. Visualization of thermally induced delamination by means of guided waves processing

    Science.gov (United States)

    Radzienski, Maciej; Kudela, Pawel; Ostachowicz, Wieslaw

    2013-04-01

    The aim of this paper is to present a method for visualization thermally induced delamination in composite material based on guided wave propagation phenomenon. Tested specimen was submitted to short time period high temperature source, which generated thermal degradation. In particular, delamination in material occurred. This procedure simulates some real case scenarios damage like one cased by atmospheric discharge striking wind turbine blade. Proposed method utilizes processing of full wavefield data acquired by the Scanning Doppler Laser Vibrometer. Registered wavefield images are transformed to wavenumber domain where the wave propagation pattern is removed. In this way after transformation signal back to space domain it contains only information about changes in wave propagation and may be used for damage visualization. However, attenuation of waves cause that visualized anomalies has lower amplitudes with increased distance from the actuator. The proposed enhancement of signal processing algorithm enables quantification of the size of the damage. The enhancement is a technique for compensation of the wave attenuation so that the effects of structural damages have the same influence regardless of the location.

  7. The effect of delaminations on local buckling in wind turbine blades

    DEFF Research Database (Denmark)

    Haselbach, Philipp Ulrich; Bitsche, Robert; Branner, Kim

    2015-01-01

    was setup in Abaqus and cohesive elements were chosen for modelling delamination growth. For initial delaminations with a width of 30–50% of the cap width the study showed that delamination close to the surface started to grow in load ranges of normal operation conditions and led to local buckling modes....... The local buckling caused high strains and stresses in the surrounding of the delamination, which exceeded the material design properties and therefore should be considered as dangerous. Delaminations placed near the mid-surface of the cap did not have a significant effect on the blade response under normal...... operation conditions. In the simulations the static load exceeded the design load by more than 40% before delamination growth or cap buckling occurred. It could be concluded that delamination induced near-surface buckling modes have to be considered critical due to an onset of local sublaminate buckling...

  8. Recycled Aluminium Cans/Eggshell Composites: Evaluation of Mechanical and Wear Resistance Properties

    Directory of Open Access Journals (Sweden)

    J.O. Agunsoye

    2015-03-01

    Full Text Available Aluminium based metal matrix composites have been produced from recycled aluminium cans and 150µm sized eggshell particles using a stir cast process. The mechanical properties of the control and aluminium can/eggshell composites produced have been investigated. The microstructures of the aluminium can/eggshell composites were examined with the aids of Scanning Electron Microscope (SEM after the sample surfaces have been carefully prepared and etched with aqueous solution of 0.5 cm3 nitric acid. Micrographs revealed that there was a homogenous distribution of eggshell particles within the aluminium can matrix. An indication of effective stirring action during the melting process. The wear resistance was also investigated under different applied loads (6 to 14 N on an abrasive surface emery paper of grade 220. The results revealed an increase in Young’s modulus of elasticity and yield stress from 1,206.45 and 50.23 Mpa respectively of the cast aluminium can with 0 % eggshell particle to the maximum of 3,258.87and 73.2 MPa of aluminium can/12 % eggshell composites. The hardness values increased from 66.23 to 75.13 VN. There was a gradual increase in wear rate of the tested samples as the applied load increased. However, the wear resistance of the aluminium can/6 % eggshell and aluminium can/12 % eggshell composites increased significantly. Hence, recycling of aluminium cans and eggshells can be harnessed into development of useful engineering metal matrix composite materials.

  9. Resistivity-Temperature Behavior of CB-Filled HDPE Foaming Composites

    Institute of Scientific and Technical Information of China (English)

    LI Ji-xin; ZHANG Guo; LI Zhuo-shi; WANG Xin-lei; LIU Xiu-qi

    2008-01-01

    High-density polyethylene/carbon black foaming conductive composites were prepared from acetylene black(ACET)and super conductive carbon black(HG-IP)as conductive filler,low-density polyethylene(LDPE)as the second component,ethylene-vinyl acetate(EVA)and ethylene propylene rubber(EPR) as the third component, azobisformamide(AC)as foamer,and dicumyl peroxide(DCP)as cross-linker.The structure and resistivity-temperature behavior of high-density polyethylene(HDPE)/CB foaming conductive composites were investigated.Influences of carbon black,LDPE,EVA,EPR,AC,and DCP on the foaming performance and resistivity-temperature behavior of HDPE/CB foaming conductive composites were also studied.The results reveal that HDPE/CB foaming conductive composite exhibits beaer switching characteristic;ACET-filled HDPE foaming conductive composite displays better positive temperature coefficient(PTC)effect;whereas super conductive carbon black(HG-1P)-filled HDPE foaming conducive composite shows better negative temperature coefficient(NTC)effect.

  10. Study on process and characterization of high-temperature resistance polyimide composite

    Science.gov (United States)

    Pan, Ling-Ying; Zhao, Wei-Dong; Liu, Han-Yang; Cui, Chao; Guo, Hong-Jun

    2016-05-01

    A novel polyimide composite with upper-use temperature of 420°C was prepared by autoclave process. The thermogravimetic analysis and rheological properties of uncured polyimide resin powders were analyzed. The influences of process parameters and post-treatment process on the properties of composites were also investigated. The morphologies of polyimide composites after shear fracture were observed by scanning electron microscope (SEM). The high-temperature resistance of composite was characterized by dynamic mechanical thermal analyzer (DMTA). Results showed that the imidization reaction mainly occurred in the temperature range of 100°C~220°C, and the largest weight loss rate appearing at 145°C indicated a drastic imidization reaction occurred. The melt viscosity of polyimide resin decreased with increasing the temperature between 220°C ˜305°C, and then increased with the increase of temperature due to the molecular crosslinking reactions. The fiber volume contents and void contents could be effectively controlled by applying the pressure step by step. The fiber volume content was sensitive to the initial pressure (Pi) during the imidization. The second-stage pressure (P2) and the temperature for applying the P2 (T2) during the imidization had a great effect on the void content of composite. Good mechanical properties and interfacial adhesion of polyimide composite could obtain by optimized process. The post-treatment process can obviously increase the high-temperature resistance of polyimide composite. The polyimide composite treated at 420°C exhibited good retention of mechanical properties at 420°C and had a glass transition temperature (Tg) of 456°C. The retentions of flexible strength, flexible modulus and short beam shear strength of polyimide composite at 420°C were 65%, 84% and 62% respectively.

  11. Study on process and characterization of high-temperature resistance polyimide composite

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Ling-Ying; Zhao, Wei-Dong; Liu, Han-Yang; Cui, Chao; Guo, Hong-Jun [Aerospace Research Institute of Materials & Processing Technology (No.1 Nan Da Hong Men Road, Fengtai District, Beijing, 100076, P.R., China) (China)

    2016-05-18

    A novel polyimide composite with upper-use temperature of 420°C was prepared by autoclave process. The thermogravimetic analysis and rheological properties of uncured polyimide resin powders were analyzed. The influences of process parameters and post-treatment process on the properties of composites were also investigated. The morphologies of polyimide composites after shear fracture were observed by scanning electron microscope (SEM). The high-temperature resistance of composite was characterized by dynamic mechanical thermal analyzer (DMTA). Results showed that the imidization reaction mainly occurred in the temperature range of 100°C~220°C, and the largest weight loss rate appearing at 145°C indicated a drastic imidization reaction occurred. The melt viscosity of polyimide resin decreased with increasing the temperature between 220°C ∼305°C, and then increased with the increase of temperature due to the molecular crosslinking reactions. The fiber volume contents and void contents could be effectively controlled by applying the pressure step by step. The fiber volume content was sensitive to the initial pressure (P{sub i}) during the imidization. The second-stage pressure (P{sub 2}) and the temperature for applying the P{sub 2} (T{sub 2}) during the imidization had a great effect on the void content of composite. Good mechanical properties and interfacial adhesion of polyimide composite could obtain by optimized process. The post-treatment process can obviously increase the high-temperature resistance of polyimide composite. The polyimide composite treated at 420°C exhibited good retention of mechanical properties at 420°C and had a glass transition temperature (Tg) of 456°C. The retentions of flexible strength, flexible modulus and short beam shear strength of polyimide composite at 420°C were 65%, 84% and 62% respectively.

  12. Electrical Resistance and Microstructure of Latex Modified Carbon Fiber Reinforced Cement Composites

    Institute of Scientific and Technical Information of China (English)

    WEI Jian; CHENG Feng; YUAN Hudie

    2012-01-01

    The electrical resistance,flexural strength,and microstructure of carbon fiber reinforced cement composites (CFRC) were improved greatly by adding water-redispersible latex powder.The electrical resistance of CFRC was investigated by two-probe method.The input range of CFRC based strain sensors was therefore increased,whereas electrical resistance was increased and remained in the perfect range of CFRC sensors.The analysis of scanning electron microscopy indicated that elastic latex bridges and a latex layer existed among the interspaces of the adjacent cement hydration products which were responsible for the enhancement of the flexural strength and electrical resistance.The formation mechanism of the elastic latex bridges was also discussed in detail.The continuous moving of two opposite interfaces of the latex solution-air along the interspaces of the adjacent hydrated crystals or colloids was attributed to the formation of the elastic latex bridges.

  13. The effect of mechanical stress on electric resistance of nanographite-epoxy composites

    Science.gov (United States)

    Vovchenko, L.; Lazarenko, A.; Matzui, L.; Zhuravkov, A.

    2012-03-01

    The in-plane electric resistance Ra of composite materials (CMs) thermoexfoliated graphite(TEG)-epoxy resin(ED) under compression along compacting C-axis has been investigated by four-probe method. TEG content was 5-75 wt%. It was shown that specimens prepared by cold pressing are denser and reveal lower values of electric resistivity in comparison with specimens prepared by pouring. It was found that compression of the specimens leads to plastic deformation of specimens (εpl) and essential irreversible decrease of electric resistance during the first cycle of loading (up to 50 MPa), especially for the poured specimens with low density. Within the proposed model the contact resistance Rk between graphite particles in CM has been evaluated and it was shown that it increased with the decrease in TEG content in CM and depends on compacting method of CMs and the dispersity of graphite filler.

  14. The Impact of Morphology and Composition on the Resistivity and Oxidation Resistance of Metal Nanostructure Films

    Science.gov (United States)

    Stewart, Ian Edward

    Printed electronics, including transparent conductors, currently rely on expensive materials to generate high conductivity devices. Conductive inks for thick film applications utilizing inkjet, aerosol, and screen printing technologies are often comprised of expensive and rare silver particles. Thin film applications such as organic light emitting diodes (OLEDs) and organic photovoltaics (OPVs) predominantly employ indium tin oxide (ITO) as the transparent conductive layer which requires expensive and wasteful vapor deposition techniques. Thus an alternative to silver and ITO with similar performance in printed electronics warrants considerable attention. Copper nanomaterials, being orders of magnitude cheaper and more abundant than silver or indium, solution-coatable, and exhibiting a bulk conductivity only 6 % less than silver, have emerged as a promising candidate for incorporation in printed electronics. First, we examine the effect of nanomaterial shape on the conductivity of thick films. The inks used in such films often require annealing at elevated temperature in order to sinter the silver nanoparticles together and obtain low resistivities. We explore the change in morphology and resistivity that occurs upon heating thick films of silver nanowires (of two different lengths, Ag NWs), nanoparticles (Ag NPs), and microflakes (Ag MFs) deposited from water at temperatures between 70 and 400 °C. At the lowest temperatures, longer Ag NWs exhibited the lowest resistivity (1.8 x 10-5 O cm), suggesting that the resistivity of thick films of silver nanostructures is dominated by the contact resistance between particles. This result supported previous research showing that junction resistance between Ag NWs in thin film conductors also dominates optoelectronic performance. Since the goal is to replace silver with copper, we perform a similar analysis by using a pseudo-2D rod network modeling approach that has been modified to include lognormal distributions in length

  15. Shadowgraph studies of laser-assisted non-thermal structuring of thin layers on flexible substrates by shock-wave-induced delamination processes

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, Pierre, E-mail: pierre.lorenz@iom-leipzig.de [Leibniz-Institut für Oberflächenmodifizierung e. V., Permoserstraße 15, 04318 Leipzig (Germany); Smausz, Tomi [Department of Optics and Quantum Electronics, University of Szeged, H-6720 Szeged, Dóm tér 9 (Hungary); MTA-SZTE Research Group on Photoacoustic Spectroscopy, University of Szeged, H-6720 Szeged, Dóm tér 9 (Hungary); Csizmadia, Tamas [Department of Optics and Quantum Electronics, University of Szeged, H-6720 Szeged, Dóm tér 9 (Hungary); Ehrhardt, Martin; Zimmer, Klaus [Leibniz-Institut für Oberflächenmodifizierung e. V., Permoserstraße 15, 04318 Leipzig (Germany); Hopp, Bela [Department of Optics and Quantum Electronics, University of Szeged, H-6720 Szeged, Dóm tér 9 (Hungary)

    2015-05-01

    Highlights: • The shock-wave-induced film delamination (SWIFD) is a laser patterning process. • The SWIFD process of CIGS solar cells was studied by shadowgraph measurements. • The study presented that SWIFD allows the structuring of CIGS solar cells. • The dynamics of the delamination process was analyzed. - Abstract: The laser-assisted microstructuring of thin films especially for electronic applications without damaging the layers or the substrates is a challenge for the laser micromachining techniques. The laser-induced thin-film patterning by ablation of the polymer substrate at the rear side that is called ‘SWIFD’ – shock-wave-induced film delamination patterning has been demonstrated. This study focuses on the temporal sequence of processes that characterize the mechanism of this SWIFD process on a copper indium gallium selenide (CIGS) solar cell stacks on polyimide. For this purpose high-speed shadowgraph experiments were performed in a pump probe experimental set-up using a KrF excimer laser for ablating the rear side of the polyimide substrate and measuring the shock wave generation at laser ablation of the polymer substrate as well as the thin-film delamination. The morphology and size of the thin-film structures were studied by scanning electron microscopy (SEM). Furthermore, the composition after the laser treatment was analyzed by energy dispersive X-ray (EDX) spectroscopy. The shadowgraph experiments allow the time-dependent identification and evaluation of the shock wave formation, substrate bending, and delamination of the thin film in dependence on the laser parameters. These results will contribute to improve the physical understanding of the laser-induced delamination effect for thin-film patterning.

  16. Piezoelectric and mechanical properties of fatigue resistant, self-healing PZT-ionomer composites

    Science.gov (United States)

    James, N. K.; Lafont, U.; van der Zwaag, S.; Groen, W. A.

    2014-05-01

    Piezoelectric ceramic-polymer composites with 0-3 connectivity were fabricated using lead zirconium titanate (PZT) powder dispersed in an ionomer (Zn ionomer) and its reference ethylene methacrylic acid copolymer (EMAA) polymer matrix. The PZT-Zn ionomer and PZT-EMAA composites were prepared by melt extrusion followed by hot pressing. The effects of poling conditions such as temperature, time and electric field on the piezoelectric properties of the composites were investigated. The experimentally observed piezoelectric charge coefficient and dielectric constant of the composites were compared with theoretical models. The results show that PZT-Zn ionomer composites have better piezoelectric properties compared to PZT-EMAA composites. The static and fatigue properties of the composites were investigated. The PZT-Zn ionomer composites were found to have excellent fatigue resistance even at strain levels of 4%. Due to the self-healing capabilities of the ionomer matrix, the loss of piezoelectric properties after high strain tensile cyclic loading could be partially recovered by thermal healing.

  17. Resistance Curves in the Tensile and Compressive Longitudinal Failure of Composites

    Science.gov (United States)

    Camanho, Pedro P.; Catalanotti, Giuseppe; Davila, Carlos G.; Lopes, Claudio S.; Bessa, Miguel A.; Xavier, Jose C.

    2010-01-01

    This paper presents a new methodology to measure the crack resistance curves associated with fiber-dominated failure modes in polymer-matrix composites. These crack resistance curves not only characterize the fracture toughness of the material, but are also the basis for the identification of the parameters of the softening laws used in the analytical and numerical simulation of fracture in composite materials. The method proposed is based on the identification of the crack tip location by the use of Digital Image Correlation and the calculation of the J-integral directly from the test data using a simple expression derived for cross-ply composite laminates. It is shown that the results obtained using the proposed methodology yield crack resistance curves similar to those obtained using FEM-based methods in compact tension carbon-epoxy specimens. However, it is also shown that the Digital Image Correlation based technique can be used to extract crack resistance curves in compact compression tests for which FEM-based techniques are inadequate.

  18. EFFECTS OF WHOLE BODY RESISTANCE TRAINING ON BONE STATUS AND BODY COMPOSITION IN YOUNG FEMALES

    Directory of Open Access Journals (Sweden)

    Yılmaz

    2014-12-01

    Full Text Available The purpose of this study was to determine the effects of whole body resistance training on bone status and body composition in young female. Twenty five moderately active females volunteered to participate in this study and were randomly assigned to whole body resistance trained (WRT (n=13; 23.1±2.0 years and control (C groups (n=12; 22.5±1.7 years. Height, body weight and body composition measurements were held. Total body fat (%BF, fat mass (FM, fat-free mass (FFM, and bone mineral density (BMD measurements were performed with dual-energy X-ray absorptiometry. After completing the pre-test measurements, the WRT subjects were participated in 12 week whole body resistance training. At the end of the 12-week training period, paired t-test results showed that there was a significant (p.05 change in the body weight (-.21kg or BMI (.09. In the control group, significant (p.05 change in the body weight (.85kg, FFM (.12kg, and BMD (-.002 g/cm2 after 12 week period. These results showed that 12 week whole body resistance training had a optimize effect on body composition and bone status, but had no effect on body weight and body mass index in young female subjects.

  19. Influence of cultivated landscape composition on variety resistance: an assessment based on wheat leaf rust epidemics.

    Science.gov (United States)

    Papaïx, Julien; Goyeau, Henriette; Du Cheyron, Philippe; Monod, Hervé; Lannou, Christian

    2011-09-01

    In plant pathology, the idea of designing variety management strategies at the scale of cultivated landscapes is gaining more and more attention. This requires the identification of effects that take place at large scales on host and pathogen populations. Here, we show how the landscape varietal composition influences the resistance level (as measured in the field) of the most grown wheat varieties by altering the structure of the pathogen populations. For this purpose, we jointly analysed three large datasets describing the wheat leaf rust pathosystem (Puccinia triticina/Triticum aestivum) at the country scale of France with a Bayesian hierarchical model. We showed that among all compatible pathotypes, some were preferentially associated with a variety, that the pathotype frequencies on a variety were affected by the landscape varietal composition, and that the observed resistance level of a variety was linked to the frequency of the most aggressive pathotypes among all compatible pathotypes. This data exploration establishes a link between the observed resistance level of a variety and landscape composition at the national scale. It illustrates that the quantitative aspects of the host-pathogen relationship have to be considered in addition to the major resistance/virulence factors in landscape epidemiology approaches.

  20. Development of (fe–b–c-based filler for wear-resistant composite coatings

    Directory of Open Access Journals (Sweden)

    О. V. Sukhovа

    2014-12-01

    Full Text Available Purpose. Development of multi-alloyed filler for abrasive wear-resistant composites. Methodology. The methods of microstructural, X-ray and energy-dispersive X-ray analyses were used to achieve research purpose. Micro-mechanical properties of structural constituents and abrasive wear-resistance of composites were determined. Findings. The complete dissolution of chromium and vanadium in the borides of Fe2В and FeВ that are initial structural constituents of Fe–В–С peritectic alloys has been established. These elements primarily dissolve in iron monoboride. Dissolution of molybdenum and niobium is not practically observed. As a result the phases of Мо2В, Мо2(В,С or NbВ2 can be seen in the structure. Alloying with chromium and vanadium increases compression strength and crack resistance coefficient, but that with molybdenum and niobium enhances total microhardness and hardness of the alloys. Structure formation of the interfaces between the filler and the binder of the composites based on МNМts 20-20 binder is governed by dissolution and diffusion processes when multi-alloyed (Fe–В–С alloy is applied as filler of the composites. The phase and the structural composition of contact interaction zones can be explained by re-crystallization of the filler surface layers after dissolution caused by contact with the molten binder. Consequently the macroheterogeneous structure of the composites is free of defects and strong adhesion between the filler and the binder is assured. Contact interaction intensity can be controlled by the choice of temperature- and-time infiltration regimes. Originality. The peculiarities in the formation of structure and properties of Fe2В- and FeВ-based solid solutions observed in the structure of the Fe–В–С peritectic alloys were investigated that allowed us to recommend composition of multicomponent alloy to be applied as filler of (Cu–Ni–Mn-matrix macroheterogeneous composites. Practical

  1. Influence of Ultraviolet/Ozonolysis Treatment of Nanocarbon Filler on the Electrical Resistivity of Epoxy Composites.

    Science.gov (United States)

    Perets, Yulia; Matzui, Lyudmila; Vovchenko, Lyudmila; Ovsiienko, Irina; Yakovenko, Olena; Lazarenko, Oleksandra; Zhuravkov, Alexander; Brusylovets, Oleksii

    2016-12-01

    In the present work, we have investigated concentration and temperature dependences of electrical conductivity of graphite nanoplatelets/epoxy resin composites. The content of nanocarbon filler is varied from 0.01 to 0.05 volume fraction. Before incorporation into the epoxy resin, the graphite nanoplatelets were subjected to ultraviolet ozone treatment at 20-min ultraviolet exposure. The electric resistance of the samples was measured by two- or four-probe method and teraohmmeter E6-13. Several characterization techniques were employed to identify the mechanisms behind the improvements in the electrical properties, including SEM and FTIR spectrum analysis.It is established that the changes of the relative intensities of the bands in FTIR spectra indicate the destruction of the carboxyl group -COOH and group -OH. Electrical conductivity of composites has percolation character and graphite nanoplatelets (ultraviolet ozone treatment for 20 min) addition which leads to a decrease of percolation threshold 0.005 volume fraction and increase values of electrical conductivity (by 2-3 orders of magnitude) above the percolation threshold in comparison with composite materials-graphite nanoplatelets/epoxy resin. The changes of the value and behavior of temperature dependences of the electrical resistivity of epoxy composites with ultraviolet/ozone-treated graphite nanoparticles have been analyzed within the model of effective electrical conductivity. The model takes into account the own electrical conductivity of the filler and the value of contact electric resistance between the filler particles of the formation of continuous conductive pathways.

  2. Fracture Resistance of Premolars Restored by Various Types and Placement Techniques of Resin Composites

    Directory of Open Access Journals (Sweden)

    Horieh Moosavi

    2012-01-01

    Full Text Available To verify the fracture resistance of premolars with mesioocclusodistal preparations restored by different resin composites and placement techniques. Sixty premolars were randomly divided into two groups based on type of composite resin: Filtek P60 or Nulite F, and then each group was separated into three subgroups: bulk, centripetal, and fiber insert according to the type of placement method (n=10. Single-bond adhesive system was used as composite bonding according to the manufacturer's instructions. Specimens were restored in Groups 1, 2, and 3 with Filtek P60 and in Groups 4, 5, and 6 with Nulite F. After being stored 24 hours at 37∘C, a 4 mm diameter steel sphere in a universal testing machine was applied on tooth buccal and lingual cusps at a cross-head speed of 5 mm/min until fracture occurred. Groups 3 and 6 showed higher fracture resistance than Groups 1, 2, 4, and 5. Among the placement techniques, the fiber insert method had a significant effect, but the type of composite was ineffective. The insertion technique in contrast to the type of material had a significant influence on the fracture resistance of premolar teeth.

  3. Different surface preparation techniques of porcelain repaired with composite resin and fracture resistance

    Directory of Open Access Journals (Sweden)

    Mohd Helmy Khalid Abd Wahab

    2011-01-01

    Full Text Available Background : Porcelain from prosthesis such as crown or bridge can be fractured if exposed to trauma; and, can be repaired at chairside using composite resin. Aim : To investigate the fracture resistance of few techniques of surface preparation in repairing fractured porcelain using composite resin. Materials and Methods : Eighty samples of porcelain blocks were divided into 4 groups for different surface preparations, such as, Cimara repairing kit; porcelain etch kit containing hydrofluoric acid; Panavia F resin cement; and, sandblasting using aluminium oxide, before composite resin (Filtek Z250, 3M ESPE was bonded to the prepared porcelain blocks. Twenty others samples in the control group comprised of pure porcelain blocks. The fracture resistance of each sample was tested using Instron machine (UK. Results : With the exception of the group repaired using hydrofluoric acid (3.04±1.04 Mpa, all the other groups showed significant difference in the fracture resistance values when compared to the control group (3.05 ± 1.42 MPa at P<0.05. Conclusions : Etching of the porcelain blocks with hydrofluoric acid holds promise in the repair of fractured porcelain with composite resin at chairside.

  4. Unprecedented simultaneous enhancement in damage tolerance and fatigue resistance of zirconia/Ta composites

    Science.gov (United States)

    Smirnov, A.; Beltrán, J. I.; Rodriguez-Suarez, T.; Pecharromán, C.; Muñoz, M. C.; Moya, J. S.; Bartolomé, J. F.

    2017-03-01

    Dense (>98 th%) and homogeneous ceramic/metal composites were obtained by spark plasma sintering (SPS) using ZrO2 and lamellar metallic powders of tantalum or niobium (20 vol.%) as starting materials. The present study has demonstrated the unique and unpredicted simultaneous enhancement in toughness and strength with very high flaw tolerance of zirconia/Ta composites. In addition to their excellent static mechanical properties, these composites also have exceptional resistance to fatigue loading. It has been shown that the major contributions to toughening are the resulting crack bridging and plastic deformation of the metallic particles, together with crack deflection and interfacial debonding, which is compatible with the coexistence in the composite of both, strong and weak ceramic/metal interfaces, in agreement with predictions of ab-initio calculations. Therefore, these materials are promising candidates for designing damage tolerance components for aerospace industry, cutting and drilling tools, biomedical implants, among many others.

  5. Unprecedented simultaneous enhancement in damage tolerance and fatigue resistance of zirconia/Ta composites

    Science.gov (United States)

    Smirnov, A.; Beltrán, J. I.; Rodriguez-Suarez, T.; Pecharromán, C.; Muñoz, M. C.; Moya, J. S.; Bartolomé, J. F.

    2017-01-01

    Dense (>98 th%) and homogeneous ceramic/metal composites were obtained by spark plasma sintering (SPS) using ZrO2 and lamellar metallic powders of tantalum or niobium (20 vol.%) as starting materials. The present study has demonstrated the unique and unpredicted simultaneous enhancement in toughness and strength with very high flaw tolerance of zirconia/Ta composites. In addition to their excellent static mechanical properties, these composites also have exceptional resistance to fatigue loading. It has been shown that the major contributions to toughening are the resulting crack bridging and plastic deformation of the metallic particles, together with crack deflection and interfacial debonding, which is compatible with the coexistence in the composite of both, strong and weak ceramic/metal interfaces, in agreement with predictions of ab-initio calculations. Therefore, these materials are promising candidates for designing damage tolerance components for aerospace industry, cutting and drilling tools, biomedical implants, among many others. PMID:28322343

  6. Application of Electric Capacity Measurements to Detecting Delamination in Blades of Helicopter’s Lifting and Auxiliary Rotors

    Directory of Open Access Journals (Sweden)

    Gębura Andrzej

    2017-06-01

    Full Text Available This paper represents a series of the authors’ publications concerning effects of atmospheric conditions on aircraft [5-6, 11]. Hazards connected with separation ( delamination of heating elements from blade’s spar , namely: increased susceptibility to ice formation as a result of change in aerodynamic profile, decreased deicing effectiveness, shortened life of heating elements , weakened strength of blade’s structure, are described. In order to monitor the above mentioned delamination process during its early phase, these authors proposed to measure systematically electric capacity between the heating element and blade’s spar by means of a technical method. The electric capacity measurements performed by these authors on blades both in laboratory and service conditions demonstrated their practical usefulness for assessing delamination extent as well as for identifying areas where heating element separation from spar occurred. The method in question is simple , cheap , fast and non-interferring (non-destructive as well as it does not require dismounting the blades off the helicopter. As proved in practice , it is especially useful in sea-rescue or military operational conditions. Special attention was paid to application of the method to composite blades where coming-off the heating element tape causes local overheating the blade structure , that impairs flexibility of composite’s layers and may lead even to local cracks which may trigger helicopter crash. These authors desire to apply the method as a standard unit of on-board diagnostic system in the future.

  7. Fatigue resistance and failure mode of adhesively restored custom metal-composite resin premolar implant abutments.

    Science.gov (United States)

    Boff, Luís Leonildo; Oderich, Elisa; Cardoso, Antônio Carlos; Magne, Pascal

    2014-01-01

    To evaluate the fatigue resistance and failure mode of composite resin and porcelain onlays and crowns bonded to premolar custom metal-composite resin premolar implant abutments. Sixty composite resin mesostructures were fabricated with computer assistance with two preparation designs (crown vs onlay) and bonded to a metal implant abutment. Following insertion into an implant with a tapered abutment interface (Titamax CM), each metal-composite resin abutment was restored with either composite resin (Paradigm MZ100) or ceramic (Paradigm C) (n = 15) and attached with adhesive resin (Optibond FL) and a preheated light-curing composite resin (Filtek Z100). Cyclic isometric chewing (5 Hz) was then simulated, starting with 5,000 cycles at a load of 50 N, followed by stages of 200, 400, 600, 800, 1,000, 1,200, and 1,400 N (25,000 cycles each). Samples were loaded until fracture or to a maximum of 180,000 cycles. The four groups were compared using life table survival analysis (log-rank test). Previously published data using zirconia abutments of the same design were included for comparison. Paradigm C and MZ100 specimens fractured at average loads of 1,133 N and 1,266 N, respectively. Survival rates ranged from 20% to 33.3% (ceramic crowns and onlays) to 60% (composite resin crowns and onlays) and were significantly different (pooled data for restorative material). There were no restoration failures, but there were adhesive failures at the connection between the abutment and the mesostructure. The survival of the metal-composite resin premolar abutments was inferior to that of identical zirconia abutments from a previous study (pooled data for abutment material). Composite resin onlays/crowns bonded to metal-composite resin premolar implant abutments presented higher survival rates than comparable ceramic onlays/crowns. Zirconia abutments outperformed the metal-composite resin premolar abutments.

  8. Influence of aging solutions on wear resistance and hardness of selected resin-based dental composites.

    Science.gov (United States)

    Chladek, Grzegorz; Basa, Katarzyna; Żmudzki, Jarosław; Malara, Piotr; Nowak, Agnieszka J; Kasperski, Jacek

    2016-01-01

    The purpose of this study was to investigate the effect of different plasticizing aging solutions on wear resistance and hardness of selected universal resin-based dental composites. Three light cured (one nanofilled, two microhybride) and one hybride chemical cured composites were aged at 37 °C for 48 h in distillated water, ethyl alcohol solution or Listerine mouthwash. After aging the microhardness tests were carried out and then tribological tests were performed in the presence of aging solution at 37 °C. During wear testing coefficients of friction were determined. The maximal vertical loss in micrometers was determined with profilometer. Aging in all liquids resulted in a significant decrease in hardness of the test materials, with the largest values obtained successively in ethanol solution, mouthwash and water. The effect of the liquid was dependent on the particular material, but not the type of material (interpreted as the size of filler used). Introduction of mouthwash instead of water or ethanol solution resulted in a significant reduction in the coefficient of friction. The lowest wear resistance was registered after aging in ethanol and for the chemical cured hybrid composite, but the vertical loss was strongly material dependent. The effect of different aging solution, including commercial mouthrinse, on hardness and wear was material dependent, and cannot be deduced from their category or filler loading. There is no simple correlation between hardness of resin-based dental composites and their wear resistance, but softening of particular composites materials during aging leads to the reduction of its wear resistance.

  9. Mode III effects on interface delamination

    DEFF Research Database (Denmark)

    Tvergaard, Viggo; Hutchinson, J.W.

    2008-01-01

    mode III has an effect. Subsequently, the focus is on crack growth along an interface between an elastic-plastic solid and an elastic substrate. The analyses are carried out for conditions of small-scale yielding, with the fracture process at the interface represented by a cohesive zone model. Due......For crack growth along an interface between dissimilar materials the effect of combined modes I, II and III at the crack-tip is investigated. First, in order to highlight situations where crack growth is affected by a mode III contribution, examples of material configurations are discussed where...... to the mismatch of elastic properties across the interface the corresponding elastic solution has an oscillating stress singularity, and this solution is applied as boundary conditions on the outer edge of the region analyzed. For several combinations of modes I, II and III crack growth resistance curves...

  10. Co nanoparticles induced resistive switching and magnetism for the electrochemically deposited polypyrrole composite films.

    Science.gov (United States)

    Xu, Zedong; Gao, Min; Yu, Lina; Lu, Liying; Xu, Xiaoguang; Jiang, Yong

    2014-10-22

    The resistive switching behavior of Co-nanoparticle-dispersed polypyrrole (PPy) composite films is studied. A novel design method for resistive random access memory (ReRAM) is proposed. The conducting polymer films with metal nanocrystal (NC)-dispersed carbon chains induce the spontaneous oxidization of the conducting polymer at the surface. The resistive switching behavior is achieved by an electric field controlling the oxygen ion mobility between the metal electrode and the conducting polymer film to realize the mutual transition between intrinsic conduction (low resistive state) and oxidized layer conduction (high resistive state). Furthermore, the formation process of intrinsic conductive paths can be effectively controlled in the conducting polymer ReRAM using metal NCs in films because the inner metal NCs induce electric field lines converging around them and the intensity of the electric field at the tip of NCs can greatly exceed that of the other region. Metal NCs can also bring new characteristics for ReRAM, such as magnetism by dispersing magnetic metal NCs in polymer, to obtain multifunctional electronic devices or meet some special purpose in future applications. Our works will enrich the application fields of the electromagnetic PPy composite films and present a novel material for ReRAM devices.

  11. [Lipid composition of Escherichia coli cells sensitive and resistant to tetracycline].

    Science.gov (United States)

    Kuzina, Z A; Belousova, I I; Tereshin, I M

    1977-01-01

    The following variants of E. coli resistant to tetracycline have been obtained from a strain of E. coli W-677 susceptible to 2.5 mcg/ml of the antibiotic: Ri, a recombinant resulting from crossing E. coli W-677 (recipient) and E. coli CSH-222 (donor), resistant to 200 mcg/ml of tetracycline; R2, a strain isolated upon numeros passaging E. coli W-677 on media containing the antibiotic, resistant to 25 mcg/ml of tetracycline. The ability of the resistant variants to bind the antibiotic decreased, as was found in experiments with 14C-tetracycline. Preincubation with low concentrations of the antibiotic resulted in an additional decrease of the sorption by the resistant variants, and in a decrease by 15--18 per cent in the case of the susceptible culture. The R2 variant differed in lipid composition from the parent, susceptible culture: it contained less total lipids and unsaturated fatty acids, and more branched fatty acids. The R1 variant hardly differed in lipid composition from the susceptible culture.

  12. Fracture and Delamination of Chromium Thin Films on Polymer Substrates

    Science.gov (United States)

    Cordill, M. J.; Taylor, A.; Schalko, J.; Dehm, G.

    2010-04-01

    New emerging technologies in the field of flexible electronic devices require that metal films adhere well and flex with polymer substrates. Common thin film materials used for these applications include copper (Cu) with an adhesion interlayer of chromium (Cr). Copper can be quite ductile and easily move with the polymer substrate. However, Cr is more brittle and fractures at lower strains than Cu. This study aims to examine the fracture and subsequent buckling and delamination of strained Cr films on polyimide (PI). In-situ scanning electron microscope (SEM) straining is used to systematically study the influence of film thickness on fracture and buckling strains. Film fracture and delamination depend on film thickness, and increases in crack and buckle density with decreasing thickness are explored by a shear lag model.

  13. Study of Thermal Fatigue Resistance of a Composite Coating Made by a Vacuum Fusion Sintering Method

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Thermal fatigue behavior of a Ni-base alloy chromium carbide composite coating made by a vacuum fusion sintering method are discussed. Results show that thermal fatigue behavior is associated with cyclic upper temperature and coating thickness. As the thickness of the coating decreases, the thermal fatigue resistance increases. The thermal fatigue resistance cuts down with the thermal cyclic upper temperature rising. The crack growth rate decreases with the increase in cyclic number until crack arrests. Thermal fatigue failure was not found along the interface of the coating/matrix. The tract of thermal fatigue crack cracks along the interfaces of phases.

  14. Utilization of composite fecal samples for detection of anthelmintic resistance in gastrointestinal nematodes of cattle.

    Science.gov (United States)

    George, Melissa M; Paras, Kelsey L; Howell, Sue B; Kaplan, Ray M

    2017-06-15

    Recent reports indicate that anthelmintic resistance in gastrointestinal nematodes of cattle is becoming increasingly prevalent worldwide. Presently, the fecal egg count reduction test (FECRT) is the only means available for detection of resistance to anthelmintics in cattle herds at the farm level. However, the FECRT is labor and cost intensive, and consequently is only rarely performed on cattle farms unless for research purposes. If costs could be reduced, cattle producers might be more likely to pursue drug resistance testing on their farms. One approach to reducing the cost of the FECRT, is the use of composite fecal samples for performing fecal egg counts (FEC), rather than conducting FEC on fecal samples from 15 to 20 individual animals. In this study FECRT were performed on 14 groups of cattle using both individual and composite FEC methods To measure how well the results of composite sampling reproduce those of individual sampling, Lin's Concordance Correlation Coefficient was utilized to describe both the linear relationship between methods and the slope and y-intercept of the line relating the data sets. There was little difference between the approaches with 98% agreement in mean FEC found between methods Mean FEC based on individual counts ranged between 0 and 670.6 eggs per gram of feces, indicating that the results of this study are applicable to a wide range of FEC levels. Standard error of the mean FEC and range of FEC are reported for each group prior to and following treatment to describe the variability of the data set. There was greater than 95% agreement in drug efficacy between individual and composite sampling methods, demonstrating composite sampling is appropriate to evaluate drug efficacy. Notably, for all groups tested the efficacy calculated by composite sampling was within the 95% confidence interval for efficacy calculated using individual sampling. The use of composite samples was shown to reduce the number of FEC required by 79

  15. Dynamic fracture mechanics analysis for an edge delamination crack

    Science.gov (United States)

    Rizzi, Stephen A.; Doyle, James F.

    1994-01-01

    A global/local analysis is applied to the problem of a panel with an edge delamination crack subject to an impulse loading to ascertain the dynamic J integral. The approach uses the spectral element method to obtain the global dynamic response and local resultants to obtain the J integral. The variation of J integral along the crack front is shown. The crack behavior is mixed mode (Mode 2 and Mode 3), but is dominated by the Mode 2 behavior.

  16. Wear properties of potassium titanate whiskers-reinforced Al-12Si alloy composites

    Directory of Open Access Journals (Sweden)

    Wu Shenqing

    2010-02-01

    Full Text Available Potassium titanate (K2O·6TiO2 whiskers-reinforced Al-12Si alloy composites were prepared by the squeeze casting technique. Wear properties of the composites were investigated by pin-on-disc tests under dry conditions. The experimental results showed that K2O·6TiO2 whiskers can effectively reinforce the matrix alloy and improve the wear resistance of the composite when the volume fraction of whiskers is low at 10 vol%. However, the composites with a high volume fraction of whiskers showed lower wear resistance than the Al-12Si alloy. The main wear mechanism of the composites is clarified as de-lamination and abrasive wear.

  17. Fracture resistance of zirconia-composite veneered crowns in comparison with zirconia-porcelain crowns.

    Science.gov (United States)

    Alsadon, Omar; Patrick, David; Johnson, Anthony; Pollington, Sarah; Wood, Duncan

    2017-02-11

    The objectives were to evaluate the fracture resistance and stress concentration in zirconia/composite veneered crowns in comparison to zirconia/porcelain crowns using occlusal fracture resistance and by stress analysis using finite element analysis method. Zirconia substructures were divided into two groups based on the veneering material. A static load was applied occlusally using a ball indenter and the load to fracture was recorded in Newtons (N). The same crown design was used to create 3D crown models and evaluated using FEA. The zirconia/composite crowns subjected to static occlusal load showed comparable results to the zirconia/porcelain crowns. Zirconia/composite crowns showed higher stress on the zirconia substructure at 63.6 and 50.9 MPa on the zirconia substructure veneered with porcelain. In conclusion, zirconia/composite crowns withstood high occlusal loads similar to zirconia/porcelain crowns with no significant difference. However, the zirconia/composite crowns showed higher stress values than the zirconia/porcelain crowns at the zirconia substructure.

  18. Controlled delamination of metal films by hydrogen loading

    Energy Technology Data Exchange (ETDEWEB)

    Nikitin, Eugen

    2008-11-18

    n this work we quantitatively determine the adhesion energy between metal films and their substrates. Therefore a new controlled buckling technique is established, applying the strong compressive in-plane stress that results in thin films clamped on rigid substrates during hydrogen loading. When the elastic energy stored in the H-loaded thin film exceeds the adhesion energy between film and substrate, delamination occurs. At the onset of delamination, a critical hydrogen concentration, a critical stress value and a critical bending of the substrate are present, which are quantitative measures for the adhesion energy and permit its calculation. As the critical values are determined at the onset of delamination, plastic deformation is negligible, which denies the quantitative determination of adhesion energies in conventional test setups. In multilayer-systems, adhesion energies between substrates and films that hardly absorb hydrogen can be measured by the controlled buckling technique, when the films of interest are coated with hydrogen absorbing films (active layer). The measurements are performed easily and can be repeated under the same test conditions, while variables such as the thickness of the coating materials or the boundary surface structure can be varied and optimized. In this work the adhesion energies of different materials on polycarbonate and niobium on sapphire are investigated. (orig.)

  19. Guidelines and Parameter Selection for the Simulation of Progressive Delamination

    Science.gov (United States)

    Song, Kyongchan; Davila, Carlos G.; Rose, Cheryl A.

    2008-01-01

    Turon s methodology for determining optimal analysis parameters for the simulation of progressive delamination is reviewed. Recommended procedures for determining analysis parameters for efficient delamination growth predictions using the Abaqus/Standard cohesive element and relatively coarse meshes are provided for single and mixed-mode loading. The Abaqus cohesive element, COH3D8, and a user-defined cohesive element are used to develop finite element models of the double cantilever beam specimen, the end-notched flexure specimen, and the mixed-mode bending specimen to simulate progressive delamination growth in Mode I, Mode II, and mixed-mode fracture, respectively. The predicted responses are compared with their analytical solutions. The results show that for single-mode fracture, the predicted responses obtained with the Abaqus cohesive element correlate well with the analytical solutions. For mixed-mode fracture, it was found that the response predicted using COH3D8 elements depends on the damage evolution criterion that is used. The energy-based criterion overpredicts the peak loads and load-deflection response. The results predicted using a tabulated form of the BK criterion correlate well with the analytical solution and with the results predicted with the user-written element.

  20. Hardness and wear resistance of carbon nanotube reinforced aluminum-copper matrix composites.

    Science.gov (United States)

    Nam, Dong Hoon; Kim, Jae Hwang; Cha, Seung Il; Jung, Seung Il; Lee, Jong Kook; Park, Hoon Mo; Park, Hyun Dal; Hong, Hyung

    2014-12-01

    Recently, carbon nanotubes (CNTs) have been attracted to reinforcement of composite materials due to their extraordinary mechanical, thermal and electrical properties. Many researchers have attempted to develop CNT reinforced metal composites with various fabrication methods and have shown possibilities for structural and functional applications. Among them, CNT reinforced Al matrix composites have become very attractive due to their huge structural application in industry. In this study, CNT reinforced Al-Cu matrix composites with a microstructure of homogeneous dispersion of CNTs in the Al-Cu matrix are investigated. The CNT/Al-Cu composites are fabricated by mixing of CNT/Cu composite powders and Al powders by high energy ball mill process followed by hot extrusion process. The hardness and wear resistance of the CNT/Al-Cu composites are enhanced by 1.4 and 3 times, respectively, compared to those values for the Al-Cu matrix. This remarkable enhancement mainly originates from the homogeneous dispersion of CNTs in Al-Cu matrix and self-lubricant effect of CNTs.

  1. A cohesive finite element formulation for modelling fracture and delamination in solids

    Indian Academy of Sciences (India)

    S Roy Chowdhury; R Narasimhan

    2000-12-01

    In recent years, cohesive zone models have been employed to simulate fracture and delamination in solids. This paper presents in detail the formulation for incorporating cohesive zone models within the framework of a large deformation finite element procedure. A special Ritz-finite element technique is employed to control nodal instabilities that may arise when the cohesive elements experience material softening and lose their stress carrying capacity. A few simple problems are presented to validate the implementation of the cohesive element formulation and to demonstrate the robustness of the Ritz solution method. Finally, quasi-static crack growth along the interface in an adhesively bonded system is simulated employing the cohesive zone model. The crack growth resistance curves obtained from the simulations show trends similar to those observed in experimental studies.

  2. Factors affecting the thermal shock resistance of several hafnia based composites containing graphite or tungsten. M.S. Thesis

    Science.gov (United States)

    Lineback, L. D.

    1974-01-01

    The thermal shock resistance of hafnia based composites containing graphite powder or tungsten fibers was investigated in terms of material properties which include thermal expansion, thermal conductivity, compressive fracture stress, modulus of elasticity, and phase stability in terms of the processing parameters of hot pressing pressure and/or density, degree of stabilization of the hafnia, and composition. All other parameters were held constant or assumed constant. The thermal shock resistance was directly proportional to the compressive fracture stress to modulus of elasticity ratio and was not affected appreciably by the small thermal expansion or thermal conductivity changes. This ratio was found to vary strongly with the composition and density such that the composites containing graphite had relatively poor thermal shock resistance, while the composites containing tungsten had superior thermal shock resistance.

  3. Effect of presilanization filler decontamination on aesthetics and degradation resistance of resin composites.

    Science.gov (United States)

    Yoshida, Yasuhiro; Shirai, Kenichi; Shintani, Hideaki; Okazaki, Masayuki; Suzuki, Kazuomi; Van Meerbeek, Bart

    2002-12-01

    Filler-matrix coupling determines, to a large extent, the mechanical strength and clinical longevity of dental composites. The aim of this study was to examine how far a methodology to decontaminate filler prior to silanization may improve aesthetic performance in addition to physico-mechanical properties such as degradation resistance. It was reported that filler particles are surrounded and wrapped by a film that consists of multiple layers of silane molecules. X-ray photoelectron spectroscopy, however, revealed that silanization of filler particles largely depended upon siloxane bridge (Si-O-Si) formation between the silica surface and the silane molecule rather than on intermolecular bonding between adjacent silane molecules. In this study, we showed that filler decontamination resulted in a higher translucency, thereby providing a better aesthetic potential. In addition, experimental composites produced following presilanization decontamination of filler revealed a higher Vickers hardness value and a diametral tensile strength that was resistant to degradation by thermo-cycling.

  4. Influence of composition and heat treatments on corrosion resistance of Fe-Co-BSi amorphous alloys

    Energy Technology Data Exchange (ETDEWEB)

    Angelini, E.; Antonione, C.; Baricco, M.; Rosalbino, F.; Zucchi, F. (Ist. Elettrotecnico Nazionale Galileo Ferraris, Turin (Italy) Turin Univ. (Italy) Politecnico di Torino (Italy))

    This paper studies the influence of composition and heat treatments on the corrosion resistance, in a solution of Na/sub 2/SO/sub 4/ 0.05M + H/sub 2/SO/sub 4/ 0.05M, at 1.5 pH, of a series of iron base amorphous alloys with increasing cobalt content, i.e., Fe/sub 80-x/Co/sub x/B/sub 10/Si/sub 10/ with x=0, 30, and 80. The treatments were carried out in an argon atmosphere over increasing time durations: 30, 60, 120, and 240 minutes, and increasing temperatures: 350, 400, 450 and 500 degrees C respectively. It was possible to observe that, independent of heat treatment, the corrosion resistance increased with increasing cobalt concentration. In comparing samples having the same chemical composition, it was noted that their electrochemical behaviour worsened with increasing temperature and time.

  5. Corrosion resistance of the composite materials: nanocrystalline powder – polymer type in acid environment

    Directory of Open Access Journals (Sweden)

    B. Ziębowicz

    2009-10-01

    Full Text Available Purpose: The paper presents corrosion resistance of composite materials Fe73.5Cu1Nb3Si13.5B9 – PEHD type in sulphuric acid and hydrochloric acid environments.Design/methodology/approach: Composite materials Fe73.5Cu1Nb3Si13.5B9 – PEHD type were manufactured by one-sided uniaxal pressing. The amount of polymer matrix was 2.5%, 5.0%, 7.5%, wt. Powder of the Fe73.5Cu1Nb3Si13.5B9 was made by the high-energy grinding in the shaker type 8000SPEX CertiPrep Mixer/Mill for 1 h, 3 h, 5 h. Composite materials were placed in a corrosive environment and two tests were carried out as specified below: test at the temperature of 25°C, 0.1 M solution of hydrochloric acid HCl, time 348 h; test temperature 25°C, 0.1 M solution of sulphuric acid H2SO4, time 348 h, test temperature 25°C.Findings: Obtained results of corrosion resistance allow to evaluate corrosion wear of composite materials FINEMET (Fe73.5Cu1Nb3Si13.5B9 – PEHD in acidic solutions of 0.1M HCl and 0.1M H2SO4. It was found that the composite materials with 7.5% wt. of polyethylene portion show the best corrosion resistance.Research limitations/implications: Composite materials Fe73.5Cu1Nb3Si13.5B9– PEHD type manufacturing greatly expand the application possibilities of soft magnetic materials nanocrystalline powders however further examination to obtain improved properties of magnetic composite materials and investigations of new machines and devices constructions with these materials elements are still needed.Originality/value: Results allow to complete data concerning composite materials nanocrystalline powder – polymer type which are an attractive alternative for traditional materials with specific magnetic properties. Results are the base for further investigations of the impact of corrosion environment on the magnetic properties such composite materials.

  6. Investigation of Thermostability of a Composite Resistive Material with Nanodimensional Carbon Fillers

    Science.gov (United States)

    Malinovskaya, T. D.; Vlasov, V. A.; Volokitin, G. G.; Melentyev, S. V.

    2014-06-01

    Thermostability of resistive materials based on polyurethane used as heat-liberating elements in the design of heating elements of thermoactive formworks is investigated. The application of polyurethane as a binder provides solid contact of polymer molecules with nanodimensional carbon fillers and their uniform distribution in a composite material. The influence of thermal treatment and dispersed fillers on the stability of electrophysical and thermophysical properties of carbon-filled polyurethane coatings is established.

  7. Influence of aggregate mineralogical composition on water resistance of aggregate–bitumen adhesion

    OpenAIRE

    Zhang, Jizhe; Apeagyei, Alex K.; AIREY, Gordon D; Grenfell, James R.A.

    2015-01-01

    The effects of aggregate mineralogical composition on moistures sensitivity of aggregate–bitumen bonds were investigated using four aggregate types (two limestone and two granite)and two bitumen grades (40/60 penand70/100pen). Moisture sensitivity (or water resistance) of the aggregate–bitumen bonds were characterized using retained strength obtained from three different tensile tests (peel, PATTI and pull-off). The results showed significant differences in the amount of moisture absorbed ...

  8. A study of process induced voids in resistance welding of thermoplastic composites

    OpenAIRE

    Shi, H.; Fernandez Villegas, I.; Bersee, H.E.N.

    2015-01-01

    Void formation in resistance welding of woven fabric reinforced thermoplastic composites was investigated. Void contents were measured using optical microscopy and digital image process. Un-even void distributions were observed in the joints, and more voids were found in the middle of the joints than the edges. A higher welding pressure was shown to help reduce the void generation. The mechanisms of void formation, in particular fibre de-compaction induced voids and residual moisture induced ...

  9. WATER RESISTANCE OF WOOD - PLASTIC COMPOSITES MADE FROM WASTE MATERIALS RESULTED IN THE FURNITURE MANUFACTURING PROCESS

    OpenAIRE

    Camelia COŞEREANU; Dumitru LICA; Ioan CURTU; Mariana-Domnica STANCIU

    2014-01-01

    The purpose of this paper is to present innovative wood-plastic composites made from waste materials such as ABS (acrylonitrile butadiene styrene) and wood shavings resulted in the furniture manufacturing process. From previous investigations (with regard to physical integrity and compactness of the panels), only mixtures ranging from a ratio of 100% ABS: 0% shavings to 80% ABS: 20% shavings were selected for water resistance testing. Swelling in thickness and water absorption for...

  10. Delamination on GFRP laminates impacted at room and lower temperatures: Comparison between epoxy and vinylester resins

    Science.gov (United States)

    Lopresto, Valentina; Langella, Antonio; Papa, Ilaria

    2016-10-01

    Low velocity impact tests at three different impact energy values and three different temperatures, were performed on glass fibre composite laminates made by infusion technology. Two different resins, epoxy and vinylester, were considered to impregnate the fibres: the first is mainly of aeronautical interest whereas the second one is mainly applied in Naval field. The specimens were first completely destroyed to obtain the complete load-displacement curve. The latter allowed the evaluation of the increasing impact energies, 5, 10 and 20J, used to investigate about the start and propagation of the damage inside the laminates. The delamination was investigated by the very commonly used Ultra Sound technique and the results obtained on the different materials at different temperatures were compared. A general better behaviour of vinylester resin was noted.

  11. Processing Parameters Influence on Wear Resistance Behaviour of Friction Stir Processed Al-TiC Composites

    Directory of Open Access Journals (Sweden)

    E. T. Akinlabi

    2014-01-01

    Full Text Available Friction stir processing (FSP being a novel process is employed for the improvement of the mechanical properties of a material and the production of surface layer composites. The vital role of the integrity of surface characteristics in the mechanical properties of materials has made the research studies into surface modification important in order to improve the performance in practical applications. This study investigates the effect of processing parameters on the wear resistance behavior of friction stir processed Al-TiC composites. This was achieved through microstructural characterization by using both the optical and scanning electron microscope (SEM, microhardness profiling, and tribological characterization by means of the wear. The microhardness profiling of the processed samples revealed an increased hardness value, which was a function of the TiC particles incorporated when compared to the parent material. The wear resistance property was also found to increase as a result of the TiC powder addition. The right combination of processing parameters was found to improve the wear resistance property of the composites produced.

  12. A Damage Resistance Comparison Between Candidate Polymer Matrix Composite Feedline Materials

    Science.gov (United States)

    Nettles, A. T

    2000-01-01

    As part of NASAs focused technology programs for future reusable launch vehicles, a task is underway to study the feasibility of using the polymer matrix composite feedlines instead of metal ones on propulsion systems. This is desirable to reduce weight and manufacturing costs. The task consists of comparing several prototype composite feedlines made by various methods. These methods are electron-beam curing, standard hand lay-up and autoclave cure, solvent assisted resin transfer molding, and thermoplastic tape laying. One of the critical technology drivers for composite components is resistance to foreign objects damage. This paper presents results of an experimental study of the damage resistance of the candidate materials that the prototype feedlines are manufactured from. The materials examined all have a 5-harness weave of IM7 as the fiber constituent (except for the thermoplastic, which is unidirectional tape laid up in a bidirectional configuration). The resin tested were 977-6, PR 520, SE-SA-1, RS-E3 (e-beam curable), Cycom 823 and PEEK. The results showed that the 977-6 and PEEK were the most damage resistant in all tested cases.

  13. The effects of glass ionomer and flowable composite liners on the fracture resistance of open-sandwich class II restorations.

    Science.gov (United States)

    Güray Efes, Begüm; Yaman, Batu Can; Gümüştaş, Burak; Tıryakı, Murat

    2013-01-01

    This in vitro study aimed to investigate the effects of glass-ionomer and flowable composite liners on the fracture resistance of Class II amalgam and composite restorations. Group 1 cavities were restored with amalgam and Group 4 cavities with nanofill composite after the application of a dentin-bonding agent. For the remaining groups, light-cured-glass-ionomer liner was used in a gingival floor proximal box (Groups 2, 5) or flowable composite was used as a liner (Groups 3, 6), the remainder of the cavity was restored with amalgam (Groups 2, 3) or composite (Groups 5, 6). The restorations were loaded in compression to failure. The data was analyzed using Tukey's multiple comparison test. The fracture resistance was significantly higher (p0.05). Flowable composite, glass-ionomer liners increased the fracture resistance of open-sandwich Class II amalgam restorations.

  14. Evaluation of fracture resistance of indirect composite resin crowns by cyclic impact test: influence of crown and abutment materials.

    Science.gov (United States)

    Sakoguchi, Kenji; Minami, Hiroyuki; Suzuki, Shiro; Tanaka, Takuo

    2013-01-01

    This study evaluated the effect of abutment materials on the fracture resistance of composite crowns for premolars. Composite crowns were fabricated using two different indirect composite resin materials (Meta Color Prime Art or Estenia C&B) and cemented onto either a metal (Castwell M.C. 12) or composite resin (Build-It FR and FibreKor) abutment with resin cement (Panavia F2.0). Twenty-four specimens were fabricated for four groups (n=6 each) and subjected to 280-N cyclic impact loading at 1.0 Hz. The number of cycles which caused the composite crown to fracture was defined as its fracture resistance. All data were statistically analyzed using ANOVA and the Bonferroni test (α=0.05). Composite crowns cemented onto resin abutments showed higher fracture resistance than those cemented onto metal abutments.

  15. Effect of Chemical Composition on Structure and Corrosion Resistance of Ni-Mn-Cu Cast Iron

    Directory of Open Access Journals (Sweden)

    Medyński D.

    2016-09-01

    Full Text Available In the paper, a relationship between chemical composition of Ni-Mn-Cu cast iron and its structure, hardness and corrosion resistance is determined. The examinations showed a decrease of thermodynamic stability of austenite together with decreasing nickel equivalent value, in cast iron solidifying according to both the stable and the metastable systems. As a result of increasing degree of austenite transformation, the created martensite caused a significant hardness increase, accompanied by small decline of corrosion resistance. It was found at the same time that solidification way of the alloy and its matrix structure affect corrosion resistance to a much smaller extent than the nickel equivalent value, in particular concentration of elements with high electrochemical potential.

  16. Development of Stellite alloy composites with sintering/HIPing technique for wear-resistant applications

    Energy Technology Data Exchange (ETDEWEB)

    Opris, C.D. [Department of Mechanical and Aerospace Engineering, Carleton University, 1125 Colonel By Drive, Ottawa, Ont., K1S 5B6 (Canada); Liu, R. [Department of Mechanical and Aerospace Engineering, Carleton University, 1125 Colonel By Drive, Ottawa, Ont., K1S 5B6 (Canada)]. E-mail: rliu@mae.carleton.ca; Yao, M.X. [Deloro Stellite Inc., Belleville, Ont., K8N 5C4 (Canada); Wu, X.J. [Institute for Aerospace Research, National Research Council of Canada, Ottawa, Ont., K1A 0R6 (Canada)

    2007-07-01

    Cobalt-based superalloys, Stellite 694 and Stellite 712, composites were developed with the reinforcement of titanium-carbide particles for wear-resistant applications. The specimens were fabricated using the powder metallurgy technique, combined with hot isostatic pressing. Calorimetric effects of the alloy powders were investigated using the differential scanning calorimetry technique, which provided the theoretical basis of designing the sintering cycles. The phases formed in the microstructures were analyzed using the scanning electron microscope (SEM) and energy dispersive X-ray spectrum (EDS) techniques. The wear test was conducted on a ball-on-disc tribometer. It was demonstrated that the wear resistance of the alloys had been increased significantly by the titanium-carbide reinforcement and the hot isostatic pressing process had enhanced the wear resistance of the materials.

  17. Towards mechanisms-guided resistivity-based monitoring of damage evolution in laminated composites

    KAUST Repository

    Lubineau, Gilles

    2013-04-05

    A convenient health monitoring technique for detecting degradation in laminated composite is to monitor the change of electrical resistance along multiple conduction paths within the structure. Yet, the relations between the global modification of resistivity and the exact underlying damage map is still unclear that makes diffcult to interpret these nondestructive-testing results. The challenge is then to be able to reconstruct from these global observation the underlying damage map. This is even more diffcult due to the numerous underlying damage mechanisms that can take place either at the inter laminar of intra laminar level. This paper intends to provide some preliminary insights about strategies to recover the damage state based only on global measurements. We focus here on transverse cracking detection. We introduce the homogenization process that defines at the meso scale an equivalent homogeneous ply that is energetically equivalent to the cracked one. This can be used as a first tool to reconstruct damage maps based on global resistivity measurements.

  18. Does biopolymers composition in seeds contribute to the flax resistance against the Fusarium infection?

    Science.gov (United States)

    Zeitoun, Ahmed M; Preisner, Marta; Kulma, Anna; Dymińska, Lucyna; Hanuza, Jerzy; Starzycki, Michal; Szopa, Jan

    2014-01-01

    Over the last decades, the cultivation of fibrous flax declined heavily. There are number of reasons for that fact; one of them is flax susceptibility to the pathogen infection. Damages caused mainly by fungi from genus Fusarium lead to the significant losses when cultivating flax, which in turn discourage farmers to grow flax. Therefore, to launch the new products from flax with attractive properties there is a need to obtain new flax varieties with increased resistance to pathogens. In order to obtain the better quality of flax fiber, we previously generated flax with reduced pectin or lignin level (cell wall polymers). The modifications altered also plants' resistance to the Fusarium infection. Undoubtedly, the plant defense system is complex, however, in this article we aimed to investigate the composition of modified flax seeds and to correlate it with the observed changes in the flax resistance to the pathogen attack. In particular, we evaluated the content and composition of carbohydrates (cell wall polymers: pectin, cellulose, hemicelluloses and mucilage), and phenylpropanoid compounds (lignin, lignans, phenolics). From the obtained results we concluded that the observed changes in the vulnerability to pathogens putatively correlate with the antioxidant potential of phenylpropanoids accumulated in seeds, seco-isolariciresinol and coumaric acid diglycosides in particular, and with pectin level as a carbon source for pathogens. Surprisingly, relatively less important for the resistance was the physical barrier, including lignin and cellulose amount and cellulose structure. Certainly, the hypothesis should be verified on a larger number of genotypes.

  19. Investigations on damage resistance of carbon fiber composite panels toughened using veils

    Institute of Scientific and Technical Information of China (English)

    Zhu Lingang

    2013-01-01

    This research focused on how to improve damage resistance of carbon fiber laminates.It was carried out at Cranfield University Composites Centre,Milton Keynes,UK as an MSc by research thesis project.A series of low-cost composite laminates,with or without novel veils provided by Tenax,was manufactured using current aircraft carbon fiber preforms via vacuum infusion (Ⅵ) molding in this research.All the investigations on damage resistance of these panels were carried out according to the British Standard (BS ISO 18353:2009).Initial damage was induced using a falling weight apparatus mounting a 16mm hemispherical tip.C-scan and Micrograph were employed to reveal damage characteristics.Finally,both compression after impact (CAI) and plain compression strength were experimented.The behaviors of these panels,including damage size,damage construction,residual compression strength,and compression strength reduction,were utilized to investigate how and to what extent the veils affected the damage resistance.The results show that using veils is an efficient method of improving the damage resistance of the laminates studied.Maximum 32% increase in residual compression strength is achieved via veils accompanying with 7% increase in cost.

  20. Resistance to maxillary premolar fractures after restoration of class II preparations with resin composite or ceromer.

    Science.gov (United States)

    de Freitas, Cláudia Regina Buainain; Miranda, Maria Isabel Serra; de Andrade, Marcelo Ferrarezi; Flores, Victor Humberto Orbegoso; Vaz, Luís Geraldo; Guimarães, Catanzaro

    2002-09-01

    The aim of this study was to evaluate the resistance to fracture of intact and restored human maxillary premolars. Thirty noncarious human maxillary premolars, divided into three groups of 10, were submitted to mechanical tests to evaluate their resistance to fracture. Group 1 consisted of intact teeth. Teeth in group 2 received mesio-occlusodistal cavity preparations and were restored with direct resin composite restorations. Teeth in group 3 received mesio-occlusodistal cavity preparations and were restored with ceromer inlays placed with the indirect technique. After restoration, teeth were stored at 37 degrees C for 24 hours and then thermocycled for 500 cycles at temperatures of 5 degrees C and 55 degrees C. Statistical analysis revealed that group 3 (178.765 kgf) had a significantly greater maximum rupture load than did group 1 (120.040 kgf). There was no statistically significant difference between groups 1 and 2 or between groups 2 and 3. Class II cavity preparations restored with indirect ceromer inlays offered greater resistance to fracture than did intact teeth. The fracture resistance of teeth restored with resin composite was not significantly different from that of either the ceromer or intact teeth.

  1. Impact Performance of 3D Integrated Cellular Woven Composite Panel

    Institute of Scientific and Technical Information of China (English)

    TIAN Wei; ZHU Cheng-yan

    2006-01-01

    This paper studied the impact resistance of 3D integrated cellular woven composite panel under persudo-static impact,comprised the test result with property of typical 3D woven composites, analyzed some parameters that maybe affect composites' impact resistance and at last used SEM to observe the damage process and mechanism of samples. The result shows that the impact resistance of 3D integrated cellular woven composites is much better than the performance of typical 3D woven composites; it is an active method to improve the impact resistance of composites that developing preform with cellular on the basis of typical 3D woven structure; for different 3D integrated cellular woven structure, the value of absorbed-energy is incrensing with the hollow percentage; tiny deformation will not emerge on samples until the acting force gets to 85% of the maximum;similar with typical 3D woven composites, the delaminated phenomenon of 3D integrated cellular woven composites is also unapparent during impact process.

  2. Antibiotics, Antibiotic Resistance Genes, and Bacterial Community Composition in Fresh Water Aquaculture Environment in China.

    Science.gov (United States)

    Xiong, Wenguang; Sun, Yongxue; Zhang, Tong; Ding, Xueyao; Li, Yafei; Wang, Mianzhi; Zeng, Zhenling

    2015-08-01

    Environmental antibiotic resistance has drawn increasing attention due to its great threat to human health. In this study, we investigated concentrations of antibiotics (tetracyclines, sulfonamides and (fluoro)quinolones) and abundances of antibiotic resistance genes (ARGs), including tetracycline resistance genes, sulfonamide resistance genes, and plasmid-mediated quinolone resistance genes, and analyzed bacterial community composition in aquaculture environment in Guangdong, China. The concentrations of sulfametoxydiazine, sulfamethazine, sulfamethoxazole, oxytetracycline, chlorotetracycline, doxycycline, ciprofloxacin, norfloxacin, and enrofloxacin were as high as 446 μg kg(-1) and 98.6 ng L(-1) in sediment and water samples, respectively. The relative abundances (ARG copies/16S ribosomal RNA (rRNA) gene copies) of ARGs (sul1, sul2, sul3, tetM, tetO, tetW, tetS, tetQ, tetX, tetB/P, qepA, oqxA, oqxB, aac(6')-Ib, and qnrS) were as high as 2.8 × 10(-2). The dominant phyla were Proteobacteria, Bacteroidetes, and Firmicutes in sediment samples and Proteobacteria, Actinobacteria and Bacteroidetes in water samples. The genera associated with pathogens were also observed, such as Acinetobacter, Arcobacter, and Clostridium. This study comprehensively investigated antibiotics, ARGs, and bacterial community composition in aquaculture environment in China. The results indicated that fish ponds are reservoirs of ARGs and the presence of potential resistant and pathogen-associated taxonomic groups in fish ponds might imply the potential risk to human health.

  3. The composition and compression of biofilms developed on ultrafiltration membranes determine hydraulic biofilm resistance.

    Science.gov (United States)

    Derlon, Nicolas; Grütter, Alexander; Brandenberger, Fabienne; Sutter, Anja; Kuhlicke, Ute; Neu, Thomas R; Morgenroth, Eberhard

    2016-10-01

    This study aimed at identifying how to improve the level of permeate flux stabilisation during gravity-driven membrane filtration without control of biofilm formation. The focus was therefore on understanding (i) how the different fractions of the biofilms (inorganics particles, bacterial cells, EPS matrix) influence its hydraulic resistance and (ii) how the compression of biofilms impacts its hydraulic resistance, i.e., can water head be increased to increase the level of permeate flux stabilisation. Biofilms were developed on ultrafiltration membranes at 88 and 284 cm water heads with dead-end filtration for around 50 days. A larger water head resulted in a smaller biofilm permeability (150 and 50 L m(-2) h(-1) bar(-1) for biofilms grown at 88 cm and 284 cm water head, respectively). Biofilms were mainly composed of EPS (>90% in volume). The comparison of the hydraulic resistances of biofilms to model fouling layers indicated that most of the hydraulic resistance is due to the EPS matrix. The compressibility of the biofilm was also evaluated by subjecting the biofilms to short-term (few minutes) and long-term variations of transmembrane pressures (TMP). A sudden change of TMP resulted in an instantaneous and reversible change of biofilm hydraulic resistance. A long-term change of TMP induced a slow change in the biofilm hydraulic resistance. Our results demonstrate that the response of biofilms to a TMP change has two components: an immediate variation of resistance (due to compression/relaxation) and a long-term response (linked to biofilm adaptation/growth). Our results provide relevant information about the relationship between the operating conditions in terms of TMP, the biofilm structure and composition and the resulting biofilm hydraulic resistance. These findings have practical implications for a broad range of membrane systems. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Joining of the AMC Composites Reinforced with Ti3Al Intermetallic Particles by Resistance Butt Welding

    Directory of Open Access Journals (Sweden)

    Adamiak M.

    2016-06-01

    Full Text Available The introduction of new reinforcing materials continues to be investigated to improve the final behaviour of AMCs as well as to avoid some drawbacks of using ceramics as reinforcement. The present work investigates the structure, properties and ability of joining aluminium EN-AW 6061 matrix composite materials reinforced with Ti3Al particles by resistance butt welding as well as composite materials produced by mechanical milling, powder metallurgy and hot extrusion techniques. Mechanically milled and extruded composites show finer and better distribution of reinforcement particles, which leads to better mechanical properties of the obtained products. Finer microstructure improves mechanical properties of obtained composites. The hardness increases twice in the case of mechanically milled composites also, a higher reinforcement content results in higher particle dispersion hardening, for 15 wt.% of intermetallics reinforcement concentration composites reach about 400 MPa UTS. Investigation results of joints show that best hardness and tensile properties of joints can be achieved by altering soft conditions of butt welding process e.g. current flow time 1.2 s and current 1400 A. To improve mechanical properties of butt welding joints age hardening techniques can also be used.

  5. Dry wear behaviors of wear resistant composite coatings produced by laser cladding

    Institute of Scientific and Technical Information of China (English)

    Jiang Xu; Wenjin Liu; Minlin Zhong

    2004-01-01

    Using different proportional mixtures of Ni-coated MoS2, TiC and pure Ni powders, new typical wear resistant and selflubricant coatings were formed on low carbon steel by laser cladding process. The microstructures and phase composition of the composite coatings were studied by SEM and XRD. The typical microstructure of the composite coating is composed of multisulfide phases including binary element sulfide and ternary element sulfide, γ-Ni, TiC and Mo2C. Wear tests were carried out using an FALEX-6 type pin-on-disc machine. The friction coefficient and mass loss of three kinds of MoS2/TiC/Ni laser clad coatings are lower than those of quenched 45 steel, and the worn surfaces of the laser cladding coatings are very smooth. Because of high hardness combined with low friction, the laser cladding composite coating with a mixture of 70% Ni-coated MoS2, 20%TiC and 10%pure Ni powder presents better wear behaviors than the composite coating with other powder blends. The composition analysis of the worn surface of GCr15 bearing steel shows that the transferred film from the laser cladding coating to the opposite surface of GCr15beating steel contains an amount of sulfide, which can change the micro-friction mechanism and lead to a reduced friction coefficient.

  6. Scratch-resistant, highly conductive, and high-strength carbon nanotube-based composite yarns.

    Science.gov (United States)

    Liu, Kai; Sun, Yinghui; Lin, Xiaoyang; Zhou, Ruifeng; Wang, Jiaping; Fan, Shoushan; Jiang, Kaili

    2010-10-26

    High-strength and conductive carbon nanotube (CNT) yarns are very attractive in many potential applications. However, there is a difficulty when simultaneously enhancing the strength and conductivity of CNT yarns. Adding some polymers into CNT yarns to enhance their strength will decrease their conductivity, while treating them in acid or coating them with metal nanoparticles to enhance their conductivity will reduce their strength. To overcome this difficulty, here we report a method to make high-strength and highly conductive CNT-based composite yarns by using a continuous superaligned CNT (SACNT) yarn as a conductive framework and then inserting polyvinyl alcohol (PVA) into the intertube spaces of the framework through PVA/dimethyl sulphoxide solution to enhance the strength of yarns. The as-produced CNT/PVA composite yarns possess very high tensile strengths up to 2.0 GPa and Young's moduli more than 120 GPa, much higher than those of the CNT/PVA yarns reported. The electric conductivity of as-produced composite yarns is as high as 9.2 × 10(4) S/m, comparable to HNO(3)-treated or Au nanoparticle-coated CNT yarns. These composite yarns are flexible, lightweight, scratch-resistant, very stable in the lab environment, and resistant to extremely humid ambient and as a result can be woven into high-strength and heatable fabrics, showing potential applications in flexible heaters, bullet-proof vests, radiation protection suits, and spacesuits.

  7. Effect of porosity on wear resistance of SiCp/Cu composites prepared by pressureless infiltration

    Institute of Scientific and Technical Information of China (English)

    ZHANG Lin; QU Xuan-hui; DUAN Bo-hua; HE Xin-bo; QIN Ming-li

    2008-01-01

    The influence of porosity on the wear behavior of high volume fraction (61%) SiCp/Cu composite produced by pressureless infiltration was studied using a sliding, reciprocating and vibrating(SRV) machine. SiCp/Cu composites slid against hardened GCr15 bearing steel ball in the load range of 40-200 N. The results show that the wear rate increases with increasing porosity. The composite containing low porosity shows excellent wear resistance, which is attributed to the presence of mechanically mixed layer on the worn surface. In this case, the dominant wear mechanism is oxidative wear. Comparatively, the composite containing high porosity exhibits inferior wear resistance. Fracture and spalling of the particles are considered as the main causes of severe wear. Third body abrasion is the controlling wear mechanism. In addition, porosity has more important influence on wear rate at high load than at low load. This is associated with the fact that the fracture and spalling of particles is a process of crack initiation and propagation. At lower load, the pores beneath the worn surface can not propagate significantly, while the pores become unstable and easily propagate under high load, which results in a higher wear rate.

  8. Radiation-resistant composite scintillators based on GSO and GPS grains

    Science.gov (United States)

    Boyarintsev, A. Yu.; Galunov, N. Z.; Gerasymov, Ia. V.; Karavaeva, N. L.; Krech, A. V.; Levchuk, L. G.; Popov, V. F.; Sidletskiy, O. Ts.; Sorokin, P. V.; Tarasenko, O. A.

    2017-01-01

    The effect of irradiation on the scintillation light output, optical transmittance, and luminescent spectra of composite scintillators based on grains of single crystals Gd2SiO5:Ce (GSO) and Gd2Si2O7:Ce (GPS) is studied. The dielectric gel Sylgard-184 is the base and the binder for the grains inside the composite scintillator. The paper presents and analyzes the results obtained for the scintillators exposed by 10 MeV electrons from the linear electron accelerator at room temperature. The exposure doses D≤250 Mrad. The dose rate is 0.2 or 1500 Mrad/h. The study has shown that the composite scintillators based on the grains of GSO and GPS are radiation-resistant over the range of the irradiation.

  9. Vibration of a delaminated beam-plate relative to buckled states

    Science.gov (United States)

    Yin, W.-L.; Jane, K. C.

    1992-07-01

    Free vibrations of delaminated beam-plates with respect to postbuckled referential states are studied. If the postbuckling deformation of the referential state is symmetric with respect to the mid-point, then the symmetric and antisymmetric vibration modes are uncoupled. Short delaminations which do not significantly degradate the overall stiffness of the beam-plate have little effect on the lowest modes of vibration and their frequencies, while the presence of a long delamination generally introduces additional vibration frequencies, the associated mode shapes of which show out-of-phase motions of the upper and lower delaminated layers. These new vibration modes and frequencies depend sensitively on the delamination length and location and on the magnitude of the postbuckling load. Hence their detection may indicate the presence and the nature of internal delamination damage.

  10. The correlation of low-velocity impact resistance of graphite-fiber-reinforced composites with matrix properties

    Science.gov (United States)

    Bowles, K. J.

    1986-01-01

    Summarized are basic studies that were conducted to correlate the impact resistance of graphite-fiber-reinforced composites with polymer matrix properties. Three crosslinked epoxy resins and a linear polysulfone were selected as composite matrices. As a group, these resins possess a significantly large range of mechanical properties. The mechanical properties of the resins and their respective composites were measured. Neat resin specimens and unidirectional and crossply composite specimens were impact tested with an instrumented dropweight tester. Impact resistances of the specimens were assessed on the basis of loading capability, energy absorption, and extent of damage.

  11. Effect of fibre-reinforced composite on the fracture resistance of endodontically treated teeth.

    Science.gov (United States)

    Ozsevik, Abdul Semih; Yildirim, Cihan; Aydin, Ugur; Culha, Emre; Surmelioglu, Derya

    2016-08-01

    The aim of this study is to evaluate the fracture resistance of root-filled teeth restored with fibre-reinforced composite (everX posterior). Fifty mandibular molars were divided into five groups (n = 10). Group 1: no treatment was applied (intact teeth). Group 2-5: canals were prepared and root filled. Group 2: no coronal restoration was placed. Group 3: teeth were coronally restored with composite. Group 4: composite restorations were performed following polyethylene fibre insertion at the cavity base. Group 5: composite resin placed over everX posterior. After thermocycling (5-55°C, 5000×), fracture resistance was measured. Mean force load for each sample was recorded in Newtons (N). Results were statistically analysed with one-way analysis of variance and post hoc Tukey's tests. The mean force required to fracture samples and standard deviations are as follows: group 1: 2859.5 ± 551.27 N, group 2: 318.97 ± 108.67 N, group 3: 1489.5 ± 505.04 N, group 4: 1958.3 ± 362.94 N, group 5: 2550.7 ± 586.1 N. everX posterior (group 5) was higher than groups 2, 3 and 4 (P  0.05). Placing fibre-reinforced composite under composite increased the fracture strength of root-filled teeth to the level of intact teeth.

  12. Influence of Different Bonding Agents and Composite Resins on Fracture Resistance of Reattached Incisal Tooth Fragment

    Directory of Open Access Journals (Sweden)

    Davari AR.

    2014-03-01

    Full Text Available Statement of Problem: Reattachment of the fractured tooth fragment should be considered as a conservative treatment and valid alternative to a composite restoration. Purpose: This in vitro study was to evaluate the influence of different adhesives and composite resins on fracture resistance of dental fragment reattached to sectioned incisal edges. Materials and Method: 120 sound human maxillary central incisors were selected under standard conditions and randomly divided into 3 groups, 12 sound teeth were used as a control group and the remaining teeth were assigned to 3 groups (n=36 and each group into three subgroups (n=12. The incisal third of samples was sectioned using a diamond disk and the respective fragments were then reattached utilizing different intermediate restorative materials, namely: i adhesive materials alone (OptiBond S or OptiBond XTR or OptiBond All-in-One; ii Premise flowable composite and iii Point 4 composite in the one of mentioned adhesive interface. After storage for two weeks at 37°C and 100% humidity and then thermocycling; shear bond strength (SBS was recorded in kilogram force (kgf by applying a load in the middle incisal third with a Zwick Universal Testing Machine at a cross-head speed of 1 mm/min. Data was analyzed with one-way ANOVA and Tukey HSD (p< 0.05. Results: The control group had a significantly higher SBS than other groups (p= 0.001; the highest SBS values was obtained using the premise flowable composite and OptiBond S adhesive (112.44±30.46 Mpa; and the lowest with OptiBond All-in-One alone (33.97± 15.63 Mpa. Conclusion: Although, none of the tested materials provided fracture resistance similar to that found with the intact maxillary central incisors; utilizing the premise flowable composite and OptiBond S adhesive improved the SBS of the reattached fragment than other materials.

  13. Retraction pattern of delaminated rotator cuff tears: dual-layer rotator cuff repair

    OpenAIRE

    Cha, Sang-Won; Lee, Choon-Key; Sugaya, Hiroyuki; Kim, Taegyun; Lee, Su-Chan

    2016-01-01

    Background There has been no report to date regarding retraction patterns of delaminated rotator cuff tears. The purpose of this study was to evaluate the incidence and tearing patterns of delamination and repair integrity after the dual-layer repair of delaminated cuff tears. Methods/design A consecutive series of 64 patients with posterosuperior rotator cuff tears underwent arthroscopic rotator cuff repair from August 2011 to September 2012. Among the patients, 53 who received either dual-l...

  14. Delamination Method In English Teaching Can Also Be Applicable In Senior Middle School

    Institute of Scientific and Technical Information of China (English)

    于淑兰; 滕越

    2015-01-01

    The paper makes a research on delamination method in English teaching in senior middle school—a dimension of English teaching.By applying theories of linguistics,the author analyzes the present situation of the application of delamination method in English teaching both in college school and in senior middle school and a conclusion is,then,drawn that delamination English teaching can also be applicable in senior middle school.

  15. PREPARATION AND CORROSION RESISTANCE OF NiP/TiO2 COMPOSITE FILM ON CARBON STEEL IN SULFURIC ACID SOLUTION

    Institute of Scientific and Technical Information of China (English)

    L.Z. Song; S.Z. Song; J. Zhao

    2006-01-01

    A NiP/TiO2 composite film on carbon steel was prepared by electroless plating and sol-gel composite process. An artificial neural network was applied to optimize the prepared condition of the composite film. Corrosion behavior of the NiP/TiO2 composite film was investigated by polarization resistance measurement, anode polarization, ESEM (environmental scanning electron microscopy)and EIS (electrochemical impedance spectroscopy) measurements. Results showed that the NiP/TiO2 composite film has a good corrosion resistance in 0.5mol/L H2SO4 solution. The element valence of the composite film was characterized by XPS (X-ray photoelectron spectroscopy) spectrum, and an anticorrosion mechanism of the composite film was discussed.

  16. The comparative evaluation of fracture resistance and microleakage in bonded amalgam, amalgam, and composite resins in primary molars

    Directory of Open Access Journals (Sweden)

    H S Vanishree

    2015-01-01

    Conclusions: Bonded amalgam appears to be comparable to amalgam when microleakage is considered and to composite resin when fracture resistance is considered; hence, bonded amalgam can also be an alternative material to amalgam in primary molars.

  17. Short review: Potential impact of delamination cracks on fracture toughness of structural materials

    Directory of Open Access Journals (Sweden)

    X.C. Arnoult

    2016-02-01

    Full Text Available The current energy policy envisages extended lifetime for the current nuclear power plants (GEN II NPP. This policy imposes a large research effort to understand the ageing of power plant components. In this goal, it is necessary to improve knowledge about safety, reliability and components’ integrity for more than forty years of operation. In Central and Eastern Europe, the majority of NPPs are VVER types, where some of the components are produced from austenitic steel 08Ch18N10T. Irradiated 08Ch18N10T may exhibit brittle behavior, namely delamination cracks are found in some cases on the fracture surface of irradiated 08Ch18N10T with elongated δ-ferrite. Delamination cracks have also been observed on the fracture surface of high-strength steels or aluminum-lithium alloys. This article presents a state-of-the art review to provide a detailed analysis of the influence of delamination cracks on the toughness of metal alloys. In general, the delamination cracks are present in metal alloys having a high texture and microstructure anisotropy. Three types of delamination cracks have been observed and are classified as crack arrester delamination, crack divider delamination and crack splitting delamination. The microscopy characterization, 3D fracture theories and computational studies explaining possible causes and effects of delamination cracks on the mechanical properties of metal alloys are presented.

  18. Ion sputtering erosion mechanisms of h-BN composite ceramics with textured microstructures

    Energy Technology Data Exchange (ETDEWEB)

    Duan, Xiaoming, E-mail: dxm_hit@126.com [Institute for Advanced Ceramics, Harbin Institute of Technology, Harbin 150001 (China); Ding, Yongjie [School of Energy Science and Technology, Harbin Institute of Technology, Harbin 150001 (China); Jia, Dechang; Jing, Nan; Yang, Zhihua; He, Peigang; Tian, Zhuo; Wang, Shengjin; Wang, Yujin; Zhou, Yu [Institute for Advanced Ceramics, Harbin Institute of Technology, Harbin 150001 (China); Yu, Daren [School of Energy Science and Technology, Harbin Institute of Technology, Harbin 150001 (China)

    2014-11-15

    Highlights: • Textured h-BN ceramics were made by hot press sintering using mullite as additives. • Sintering pressures play important role on ions sputtering resistance properties. • Textured microstructures lead to various surface morphologies by ion sputtering. • Sputtering erosion mechanisms include B–N bonds breaking and BN layers delamination. - Abstract: Since the hexagonal boron nitride (h-BN) grain shows typical lamellar structures, textured materials can be obtained by arranging h-BN grains along one direction. In this work, textured h-BN composite ceramics with the c-axis orientation arranged along the pressure direction are manufactured by hot-press sintering using mullite as the sintering additive. The results show that sintering pressures not only play a major role in the density and the textured degrees of composite ceramics, but also influence Xe ion erosion resistance performances. After Xe ion sputtering, compositions of both h-BN and mullite stay stable, while the elemental compositions have changed due to the so-called “preferential sputtering”. Sputtered surfaces along different orientations show diverse morphologies attributed to the textured microstructures. The erosion mechanisms of h-BN grains during Xe ion sputtering are breaking of B–N bonds and delamination of BN layers. While the mass loss of composite ceramics is due to the erosion of h-BN grains and mullite coupled with partial detachment of h-BN grains from the surface.

  19. Tensile/Shear Behaviour of Multi-stitched/Nano Composites

    Science.gov (United States)

    Bilisik, Kadir; Kaya, Gaye

    2017-02-01

    This study aims to investigate tensile/shear behavior of multi-stitched/nano composites. For this purpose, non-stitched, non-stitched/nano, multi-stitched and multi-stitched/nano composites were made. It was shown that the warp/filling tensile strength and modulus of composites were slightly reduced in both multi-stitched and multi-stitched/nano composites due to fiber breakage that resulted from the multi-stitching process. In addition, there were not significant differences between non-stitched and multi-stitched structures. The non-stitched/nano composite showed slightly higher in-plane shear strength compared with the non-stitched composite. The in-plane shear strength of the non-stitched composite, on the other hand, increased steadily compared to the multi-stitched composite because of the stitching process and the interface between the stitching yarn and polymer matrix. Stitching significantly improved the delamination resistance in the multi-stitched and multi-stitched/nano composites experienced a small amount of damaged areas. The incorporation of nano silica improved the damage resistance of multi-stitched composites. Therefore, the damaged tolerance composite was developed with stitching and the addition of the nano silica for various industrial applications, such as electronic boards.

  20. Copper Nanoparticle/Multiwalled Carbon Nanotube Composite Films with High Electrical Conductivity and Fatigue Resistance Fabricated via Flash Light Sintering.

    Science.gov (United States)

    Hwang, Hyun-Jun; Joo, Sung-Jun; Kim, Hak-Sung

    2015-11-18

    In this work, multiwalled carbon nanotubes (MWNTs) were employed to improve the conductivity and fatigue resistance of flash light sintered copper nanoparticle (NP) ink films. The effect of CNT weight fraction on the flash light sintering and the fatigue characteristics of Cu NP/CNT composite films were investigated. The effect of carbon nanotube length was also studied with regard to enhancing the conductivity and fatigue resistance of flash light sintered Cu NP/CNT composite films. The flash light irradiation energy was optimized to obtain high conductivity Cu NP/CNT composite films. Cu NP/CNT composite films fabricated via optimized flash light irradiation had the lowest resistivity (7.86 μΩ·cm), which was only 4.6 times higher than that of bulk Cu films (1.68 μΩ·cm). It was also demonstrated that Cu NP/CNT composite films had better durability and environmental stability than those of Cu NPs only.

  1. Highly sensitive piezo-resistive graphite nanoplatelet-carbon nanotube hybrids/polydimethylsilicone composites with improved conductive network construction.

    Science.gov (United States)

    Zhao, Hang; Bai, Jinbo

    2015-05-13

    The constructions of internal conductive network are dependent on microstructures of conductive fillers, determining various electrical performances of composites. Here, we present the advanced graphite nanoplatelet-carbon nanotube hybrids/polydimethylsilicone (GCHs/PDMS) composites with high piezo-resistive performance. GCH particles were synthesized by the catalyst chemical vapor deposition approach. The synthesized GCHs can be well dispersed in the matrix through the mechanical blending process. Due to the exfoliated GNP and aligned CNTs coupling structure, the flexible composite shows an ultralow percolation threshold (0.64 vol %) and high piezo-resistive sensitivity (gauge factor ∼ 10(3) and pressure sensitivity ∼ 0.6 kPa(-1)). Slight motions of finger can be detected and distinguished accurately using the composite film as a typical wearable sensor. These results indicate that designing the internal conductive network could be a reasonable strategy to improve the piezo-resistive performance of composites.

  2. Development and Validation of a Novel Bird Strike Resistant Composite Leading Edge Structure

    Science.gov (United States)

    Kermanidis, Th.; Labeas, G.; Sunaric, M.; Ubels, L.

    2005-11-01

    A novel design of a fibre-reinforced composite Leading Edge (LE) of a Horizontal Tail Plain (HTP) is proposed. The development and validation approach of the innovative composite LE structure are described. The main design goal is the satisfactory impact resistance of the novel composite LE in the case of bird strike. The design concept is based on the absorption of the major portion of the bird kinetic energy by the composite skins, in order to protect the ribs and the inner LE structure from damaging, thus preserving the tail plane functionality for safe landing. To this purpose, the LE skin is fabricated from specially designed composite panels, so called ‘tensor skin’ panels, comprising folded layers, which unfold under the impact load and increase the energy absorption capability of the LE. A numerical model simulating the bird strike process is developed and bird strike experimental testing is performed, in order to validate the proposed layout and prove the capability of the structure to successfully withstand the impact loading. The numerical modelling issues and the critical parameters of the simulation are discussed. The present work is part of the European Aeronautics Research Project, ‘Crashworthiness of aircraft for high velocity impact CRAHVI’ [1].

  3. EFFECT OF SURFACE SEALING ON STAIN RESISTANCE OF A NANO-HYBRID RESIN COMPOSITE*

    Directory of Open Access Journals (Sweden)

    Günçe SAYGI

    2015-04-01

    Full Text Available Purpose: This study investigated the influence of sealant application on stain resistance of a nanohybrid resin composite compared to the efficacy of a bonding agent used as a surface sealant on prolonging color stability of the resin composite. Materials and Methods: 28 disc-shaped materials were prepared from a nano-hybrid resin composite Filtek Z550 and assigned to four groups: G1K: nonsealed; G2:Adper Single Bond; G3: Fortify ; G4: Biscover LV. After 24 h storage in distilled water at 37˚C, all specimens were subjected to thermocycling and immersed into coffee solution. Color measurements were performed using spectrophotometer (VITA Easyshade; Vident according to CIEL*a*b* system. Results: Color change values were significantly different among the groups in each evaluation period except for after thermocycling (p<0.05. For 7 days evaluation period, the difference between G3 and G4 group was statistically significant while G4 exhibited statistically significant differences (p<0.05 and p<0.0001 respectively compared to control (G1 in 14 day whereas no significant difference was found between GI and GII in 28-day evaluation period. However, ΔE values of sealed specimens (GIII, GIV differed significantly from non-sealed (GI specimens after 28 days of immersion in coffee solution (p<0.05 and p<0.0001 respectively. Conclusion: It may be concluded that using a bonding agent as a surface sealant does not increase stain resistance of resin composites of the sealants evaluated. Biscover LV showed the highest efficacy to prolong color stability of the resin composite.

  4. Ductile film delamination from compliant substrates using hard overlayers

    Science.gov (United States)

    Cordill, M.J.; Marx, V.M.; Kirchlechner, C.

    2014-01-01

    Flexible electronic devices call for copper and gold metal films to adhere well to polymer substrates. Measuring the interfacial adhesion of these material systems is often challenging, requiring the formulation of different techniques and models. Presented here is a strategy to induce well defined areas of delamination to measure the adhesion of copper films on polyimide substrates. The technique utilizes a stressed overlayer and tensile straining to cause buckle formation. The described method allows one to examine the effects of thin adhesion layers used to improve the adhesion of flexible systems. PMID:25641995

  5. Undulatory delamination of thin polymer films on gold surfaces.

    Science.gov (United States)

    Chah, Soonwoo; Noolandi, Jaan; Zare, Richard N

    2005-10-20

    Using two-dimensional surface plasmon resonance measurements, we have observed the formation of traveling waves in the delamination of thin films of polydimethylsilane (PDMS) exposed to methanol. Films were spin-coated on a gold surface and the methanol was added to the top surface. The stress-induced instability caused by the swelling of the PDMS thin film when its edge is pinned to the gold surface leads to wrinkle formation and propagation at the interface. The periodic pattern is thought to be the result of an Asaro-Tiller-Grinfeld (ATG) instability.

  6. Wear Resistance and Structure of Electrodeposited RE-Ni-W-P-SiC-PTFE Composite Materials

    Institute of Scientific and Technical Information of China (English)

    GuoZhongcheng; ZhuXiaoyun; YangXianwan

    2004-01-01

    Effects of heat treatment temperature and time on hardness and wear resistance of RE-Ni-W-P-SiC-PTFE and RE-Ni-W-P-SiC composite coatings were studied. The results indicated that the hardness of the composite coatings as-deposited was lower and the mass loss (i.e. rate of abrasion) was higher, while the hardness increased and the rate of abrasion decreased with the increase of heat treatment temperature. The rate of abrasion was the lowest and hardness was the highest at 400℃ . The hardness decreased and the rate of abrasion increased with the temperature increasing continuously. Both the hardness and wear resistance also increased with the prolongation of heat treatment time, reaching their peak values when the heat treatment time was 2 h. The experimental results also showed that the hardness of the coatings decreased with PTFE quantity enhancing, but the wear rate diminished correspondingly. X-ray diffraction analysis indicated that the structure of RE-Ni-W-P-SiC-PTFE composite coating as-deposited is amorphous, and it partly became crystal when heat treatment temperature was over 3000℃.

  7. Antibiotic resistance genes occurrence and bacterial community composition in the Liuxi River

    Directory of Open Access Journals (Sweden)

    Wenguang eXiong

    2014-12-01

    Full Text Available Antibiotic resistance genes (ARGs in the environment have paid great concern due to their health risk. We investigated antibiotics concentrations (tetracyclines, sulfonamides and fluoroquinolones, ARGs abundances (tetracycline, sulfonamide and plasmid-mediated quinolone resistance (PMQR genes, and bacterial community composition in sediment and water samples in the Liuxi River, China. Antibiotics concentrations were determined by ultra-performance liquid chromatography-electrospray tandem mass spectrometry. ARGs abundances were quantified by a culture-independent method. Bacterial community composition was analyzed by metagenomic approach based on Ion Torrent Personal Genome Machine platform. Antibiotics concentrations were at the levels of 1.19 to 622 ug kg-1 in sediment samples and below the limit of detection to 127 ng L-1 in water samples. Relative abundances (ARGs copies/16S rRNA gene copies of detected ARGs were at the range of 10-5 to 10-2. The dominant phyla were Proteobacteria, Bacteroidetes and Verrucomicrobia in sediment samples, and were Proteobacteria, Actinobacteria and Bacteroidetes in water samples. The results indicated that the river environment was contaminated by antibiotics and may be as a reservoir of ARGs. This study provided quantitative data on antibiotics, ARGs and bacterial community composition in the Liuxi River, a geographical location different from the reported studies.

  8. Comparison of fracture resistance of teeth restored with ceramic inlay and resin composite: An in vitro study

    Directory of Open Access Journals (Sweden)

    Priti D Desai

    2011-01-01

    Conclusion: The fracture resistant strength of teeth restored with ceramic inlay was comparable to that of the normal intact teeth or slightly higher, while teeth restored with direct composite resin restoration showed less fracture resistant strength than that of the normal teeth.

  9. Investigation on Conductive Layer, Delamination, and Recast Layer Characteristics of Electro-discharge Machined Holes in TBCs

    Science.gov (United States)

    Wang, Li; Guo, Yongfeng; Zhang, Guowei

    2017-05-01

    In this study, electrical discharge machining (EDM) is used to directly drill normal effusion cooling holes in thermal-barrier-coated nickel-based superalloys (TBCs) via the assisting electrode method. The formation of the conductive layer was studied using scanning electron microscopy and energy-dispersive spectroscopy. The effects of the EDM process parameters including peak current, pulse duration, and duty cycle on delamination and recast layer characteristics were investigated. The analysis results indicate that the conductive layer possesses a feature of bilayer structure for the EDM of TBCs. The bottom layer is generated first due to the deposition of carbon-based products and molten brass debris, and its composition primarily contains C, Cu, Zr, and Zn; the surface layer is the result of the overlying of subsequently molten superalloy debris and carbon-based products, and its composition primarily consists of Ni, C, Cr, Nb, Co, Al, Fe, Cu, and Zr. The microcracks of the superalloy substrate only reside in the recast layer during the EDM of TBCs. The thickness of recast layer sharply increases with increasing peak current, pulse duration, and duty cycle, respectively. The delamination occurs at the ceramic coating/bond coating interface for the EDM of drilling normal holes in TBCs, and it can be eliminated by the selection of low discharge energy and appropriate duty cycle. Additionally, the length of delamination increases with increasing peak current, pulse duration, and duty cycle, respectively. The spalling of ceramic coating appears at the entrance of the hole due to the thermal-shock brittle fracture if excessive peak current, pulse duration, or duty cycle is selected.

  10. Influence of electropolishing and anodic oxidation on morphology, chemical composition and corrosion resistance of niobium

    Energy Technology Data Exchange (ETDEWEB)

    Sowa, Maciej; Greń, Katarzyna [Faculty of Chemistry, Silesian University of Technology, B. Krzywoustego Street 6, 44-100 Gliwice (Poland); Kukharenko, Andrey I. [Institute of Metal Physics, Russian Academy of Sciences-Ural Division, S. Kovalevskoi Street 18, 620990 Yekaterinburg (Russian Federation); Ural Federal University, Mira Street 19, 620002 Yekaterinburg, Mira str. 19 (Russian Federation); Korotin, Danila M. [Institute of Metal Physics, Russian Academy of Sciences-Ural Division, S. Kovalevskoi Street 18, 620990 Yekaterinburg (Russian Federation); Michalska, Joanna [Faculty of Materials Engineering and Metallurgy, Silesian University of Technology, Krasińskiego Street 8, 40-019 Katowice (Poland); Szyk-Warszyńska, Lilianna; Mosiałek, Michał [Jerzy Haber Institute of Catalysis and Surface Chemistry PAS, Niezapominajek Street 8, 30-239 Kraków (Poland); Żak, Jerzy [Faculty of Chemistry, Silesian University of Technology, B. Krzywoustego Street 6, 44-100 Gliwice (Poland); Pamuła, Elżbieta [AGH University of Science and Technology, Faculty of Materials Science and Ceramics, Mickiewicza Avenue 30, 30-059 Kraków (Poland); Kurmaev, Ernst Z. [Institute of Metal Physics, Russian Academy of Sciences-Ural Division, S. Kovalevskoi Street 18, 620990 Yekaterinburg (Russian Federation); Cholakh, Seif O. [Ural Federal University, Mira Street 19, 620002 Yekaterinburg, Mira str. 19 (Russian Federation); Simka, Wojciech, E-mail: wojciech.simka@polsl.pl [Faculty of Chemistry, Silesian University of Technology, B. Krzywoustego Street 6, 44-100 Gliwice (Poland)

    2014-09-01

    The work presents results of the studies performed on electropolishing of pure niobium in a bath that contained: sulphuric acid, hydrofluoric acid, ethylene glycol and acetanilide. After the electropolishing, the specimens were subjected to anodic passivation in a 1 mol dm{sup −3} phosphoric acid solution at various voltages. The surface morphology, thickness, roughness and chemical composition of the resulting oxide layers were analysed. Thusly prepared niobium samples were additionally investigated in terms of their corrosion resistance in Ringer's solution. The electropolished niobium surface was determined to be smooth and lustrous. The anodisation led to the growth of barrier-like oxide layers, which were enriched in phosphorus species. - Highlights: • Pure niobium was electropolished and subsequently anodised in a H{sub 3}PO{sub 4} solution. • Phosphorus was successfully introduced into the oxide layers after the treatment. • Corrosion resistance of niobium in Ringer's solution was improved after anodising.

  11. Electrical resistance load effect on magnetoelectric coupling of magnetostrictive/piezoelectric laminated composite

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yaojin, E-mail: wangyaojin@hotmail.co [Key Laboratory of Inorganic Functional Material and Device, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 215 Chengbei Road, Jiading, Shanghai 201800 (China); Graduate University of the Chinese Academy of Sciences, Beijing 100049 (China); Zhao, Xiangyong [Key Laboratory of Inorganic Functional Material and Device, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 215 Chengbei Road, Jiading, Shanghai 201800 (China); Jiao, Jie; Liu, Linhua [Key Laboratory of Inorganic Functional Material and Device, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 215 Chengbei Road, Jiading, Shanghai 201800 (China); Graduate University of the Chinese Academy of Sciences, Beijing 100049 (China); Di, Wenning; Luo, Haosu [Key Laboratory of Inorganic Functional Material and Device, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 215 Chengbei Road, Jiading, Shanghai 201800 (China); Or, Siu Wing, E-mail: eeswor@polyu.edu.h [Department of Electrical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong)

    2010-06-25

    The effect of electrical resistance load on the magnetoelectric (ME) coupling of laminated composite of Tb{sub 0.3}Dy{sub 0.7}Fe{sub 1.92} (Terfenol-D) magnetostrictive alloy and 0.7Pb (Mg{sub 1/3}Nb{sub 2/3})O{sub 3}-0.3PbTiO{sub 3} (PMN-PT) piezoelectric single crystal is investigated at both non-resonance and resonance frequencies. The results show that (i) the ME coefficient and ME resonance frequency increase with the increase in electrical resistance load, and (ii) the maximum ME power occurs in open-circuit condition. The present study provides the basis for the design of ME sensors and their signal-processing and electronic circuits.

  12. Composition and corrosion resistance of cerium conversion films on 2195Al-Li alloy

    Institute of Scientific and Technical Information of China (English)

    SONG Dong; FENG Xingguo; SUN Mingren; MA Xinxin; TANG Guangze

    2012-01-01

    The Ce conversion films on 2195Al-Li alloy without and with post-treatment were studied and the corrosion resistance was evaluated as well.The surface morphology was observed by scanning electron microscopy (SEN),and the chemical composition was characterized by X-ray photoelectron spectroscopy (XPS).The corrosion behaviors of 2195Al-Li alloy and conversion coating were assessed by means of potentiodynamic polarization curves.The experimental results indicated that after post-treatment the surface quality was improved significantly.According to XPS,the conversion coating after post-treatment was mainly composed of CeO2,Ce2O3,Ce-OH and a little MoO3 and MoO2.The results of potentiodynamic polarization curves revealed that the conversion coating with post-treatment possessed better corrosion resistance than bare alloy and Ce conversion coating without post-treatment.

  13. Insulin resistance, exercise capacity and body composition in subjects with two hypertensive parents

    DEFF Research Database (Denmark)

    Andersen, U B; Dige-Petersen, H; Ibsen, H

    1999-01-01

    correlated to abdominal fat mass but not to insulin sensitivity. CONCLUSION: Subjects with a strong genetic predisposition to essential hypertension had increased diastolic blood pressure compared with subjects with normotensive parents, but they were not insulin resistant. This may be due to the subjects......OBJECTIVE: To study insulin resistance in subjects with strong genetic predisposition to essential hypertension, compared with non-disposed subjects. SUBJECTS: Thirty normotensive subjects aged 18-35 years whose parents both had essential hypertension, and 30 age- and sex matched subjects whose...... parents were both normotensive, were studied. Subjects or parents with diabetes and morbid obesity were excluded. METHODS: The study comprised (1) a frequent sampling oral glucose tolerance test; (2) an isoglycemic hyperinsulinemic clamp study; (3) an analysis of body composition by dual-energy X...

  14. Microstructure and Corrosion Resistance of Aluminium and Copper Composite Coatings Deposited by LPCS Method

    Directory of Open Access Journals (Sweden)

    Winnicki M.

    2016-12-01

    Full Text Available The paper presents the study of microstructure and corrosion resistance of composite coatings (Al+Al2O3 and Cu+Al2O3 deposited by Low Pressure Cold Spraying method (LPCS. The atmospheric corrosion resistance was examined by subjecting the samples to cyclic salt spray and Kesternich test chambers, with NaCl and SO2 atmospheres, respectively. The selected tests allowed reflecting the actual working conditions of the coatings. The analysis showed very satisfactory results for copper coatings. After eighteen cycles, with a total time of 432 hours, the samples show little signs of corrosion. Due to their greater susceptibility to chloride ions, aluminium coatings have significant corrosion losses.

  15. FRACTURE RESISTANCE OF 3D-C/SiC COMPOSITES AT 1300℃

    Institute of Scientific and Technical Information of China (English)

    G.C.Ji; S.R.Qiao; S.M.Du; M.Li; D.Han; J.N.Wei

    2004-01-01

    Based on the energy conservation, the elastic energy linked to the compliance change,non-elastic energy dissipated by irreversible deformation and the resistance for crack propagation were quantitatively characterized by evaluation the load/load point displacement curves tested by three points bend experiment with single notch beam at 1300℃. The cracks length was determined by compliance calibration curves. It is shown by experimental results that the compliance of 3D-C/SiC composites changes with the cracks can be described by third order polynomial. The variation of crack advancing resistance with non-dimensional equivalent crack length presents a convex curve. The crack advancing resistance increases firstly and then decreases with the non-dimensional equivalent crack length, finally is in comparatively low level. The maximum values of crack advancing resistance are 269.73k J/m2 for nondimensional equivalent crack length of 0.318 and original notch length of 0.35mm,and 138.65k J/m2 for non-dimensional equivalent crack length of 0.381 and original notch length of 2.06mm, respectively.

  16. Techniques for Reducing Thermal Contact Resistance in Steady-State Thermal Conductivity Measurements on Polymer Composites

    Science.gov (United States)

    Stacey, C.; Simpkin, A. J.; Jarrett, R. N.

    2016-11-01

    The National Physical Laboratory (NPL) has developed a new variation on the established guarded hot plate technique for steady-state measurements of thermal conductivity. This new guarded hot plate has been specifically designed for making measurements on specimens with a thickness that is practical for advanced industrial composite materials and applications. During the development of this new guarded hot plate, NPL carried out an experimental investigation into methods for minimising the thermal contact resistance between the test specimen and the plates of the apparatus. This experimental investigation included tests on different thermal interface materials for use in another NPL facility based on a commercial guarded heat flow meter apparatus conforming to standard ASTM E1530-11. The results show the effect of applying different quantities of the type of heat transfer compound suggested in ASTM E1530-11 (clause 10.7.3) and also the effect on thermal resistance of alternative types of thermal interface products. The optimum quantities of two silicone greases were determined, and a silicone grease filled with copper was found to offer the best combination of repeatability, small hysteresis effect and a low thermal contact resistance. However, two products based on a textured indium foil and pyrolytic graphite sheet were found to offer similar or better reductions in thermal contact resistance, but with quicker, easier application and the advantages of protecting the apparatus plates from damage and being useable with specimen materials that would otherwise absorb silicone grease.

  17. Muscle function and body composition profile in adolescents with restrictive anorexia nervosa: does resistance training help?

    Science.gov (United States)

    Fernández-del-Valle, Maria; Larumbe-Zabala, Eneko; Morande-Lavin, Gonzalo; Perez Ruiz, Margarita

    2016-01-01

    The aim of this study was to analyze the effects of short-term resistance training on the body composition profile and muscle function in a group of Anorexia Nervosa restricting type (AN-R) patients. The sample consisted of AN-R female adolescents (12.8 ± 0.6 years) allocated into the control and intervention groups (n = 18 each). Body composition and relative strength were assessed at baseline, after 8 weeks and 4 weeks following the intervention. Body mass index (BMI) increased throughout the study (p = 0.011). Significant skeletal muscle mass (SMM) gains were found in the intervention group (p = 0.045, d = 0.6) that correlated to the change in BMI (r = 0.51, p  0.60) with change in BMI in both the groups. Significant relative strength increases (p strength when resistance training is prescribed. Although FM, relative body fat (%BF), BMI and body weight (BW) are used to monitor nutritional progress. Based on our results, we suggest to monitor SMM and relative strength ratios for a better estimation of body composition profile and muscle function recovery. Implications for Rehabilitation Anorexia Nervosa Restricting Type (AN-R) AN-R is a psychiatric disorder that has a major impact on muscle mass content and function. However, little or no attention has been paid to muscle recovery. High intensity resistance training is safe for AN-R after hospitalization and enhances the force generating capacity as well as muscle mass gains. Skeletal muscle mass content and muscular function improvements are partially maintained for a short period of time when the exercise program ceases.

  18. Metagenomic profiling of microbial composition and antibiotic resistance determinants in Puget Sound.

    Directory of Open Access Journals (Sweden)

    Jesse A Port

    Full Text Available Human-health relevant impacts on marine ecosystems are increasing on both spatial and temporal scales. Traditional indicators for environmental health monitoring and microbial risk assessment have relied primarily on single species analyses and have provided only limited spatial and temporal information. More high-throughput, broad-scale approaches to evaluate these impacts are therefore needed to provide a platform for informing public health. This study uses shotgun metagenomics to survey the taxonomic composition and antibiotic resistance determinant content of surface water bacterial communities in the Puget Sound estuary. Metagenomic DNA was collected at six sites in Puget Sound in addition to one wastewater treatment plant (WWTP that discharges into the Sound and pyrosequenced. A total of ~550 Mbp (1.4 million reads were obtained, 22 Mbp of which could be assembled into contigs. While the taxonomic and resistance determinant profiles across the open Sound samples were similar, unique signatures were identified when comparing these profiles across the open Sound, a nearshore marina and WWTP effluent. The open Sound was dominated by α-Proteobacteria (in particular Rhodobacterales sp., γ-Proteobacteria and Bacteroidetes while the marina and effluent had increased abundances of Actinobacteria, β-Proteobacteria and Firmicutes. There was a significant increase in the antibiotic resistance gene signal from the open Sound to marina to WWTP effluent, suggestive of a potential link to human impacts. Mobile genetic elements associated with environmental and pathogenic bacteria were also differentially abundant across the samples. This study is the first comparative metagenomic survey of Puget Sound and provides baseline data for further assessments of community composition and antibiotic resistance determinants in the environment using next generation sequencing technologies. In addition, these genomic signals of potential human impact can be used

  19. Correlation of chemical compositions of cassava varieties to their resistance to Prostephanus truncatus Horn (Coleoptera: Bostrichidae).

    Science.gov (United States)

    Osipitan, Adebola A; Sangowusi, Victoria T; Lawal, Omoniyi I; Popoola, Kehinde O

    2015-01-01

    The preference of cassava as a major host by Prostephanus truncatus Horn is a major constraint to ample production of cassava, Manihot esculenta Crantz and storage. This study analyzed the nutritional and secondary metabolite compositions in 15 cassava varieties, evaluated levels of damage and reproduction by P. truncatus, and assessed their resistance to attack. One hundred grams of dried cassava chips in 250-ml Kilner jars were infested with 10 adult larger grain borerof 0-10 days old and held for 3 months. The nutritional and secondary metabolites compositions of the dry cassava chips were determined using the method of Association of Analytical Chemists . Chip perforation rates in the cassava varieties ranged from 17.7 to 71.6%. The weight of cassava powder varied by about threefold. The final number of larger grain borer in the cassava varieties varied by about sixfold with 63 in 01/0040 and 379 in 01/1368. Hydrocyanic acid content content varied by over 10-fold and correlated negatively with number of larger grain borer. Flavonoid content varied by ∼10%. Tannins and saponin content of the cassava negatively correlated with number of adult P. truncatus. The cassava varieties 95/0166, 92/0326, 01/0040, 05/0024, and 34 91934 had selection index 0.8 were classified as susceptible. The resistance to high damage in the resistant varieties was conferred by secondary metabolites such as tannins, saponins, alkaloids, and hydrocyanic acid content. The genetic variation in cassava varieties could be explored to breed resistant cassava varieties for use in larger grain borer-endemic areas.

  20. Liners of thermoplastic composites in oil field tubulars

    Energy Technology Data Exchange (ETDEWEB)

    Melve, B. [Statoil Research Centre, Trondheim (Norway); Grini, K. [Univ. of Trondheim, Trondheim (Norway)

    1997-12-31

    The buckling resistance of thermoplastic composite liners in steel production tubing has been studied by theoretical models, numeric models and practical collapse tests. The materials studied were hoop wound glass fibre/polypropylene with and without a pure polypropylene inner layer. The numerical results show that a large increase in buckling resistance is achieved when the liner is partially supported by the steel tube in comparison with a free liner. The test results for the unsupported liner were in agreement with standard theories. The combined laminate did not perform as well as predicted because the polypropylene layer delaminated and buckled away from the composite layer. Thermoforming of the ends to suit the threaded end connectors was also shown to be possible. (au)

  1. Influence of Ultraviolet/Ozonolysis Treatment of Nanocarbon Filler on the Electrical Resistivity of Epoxy Composites

    Science.gov (United States)

    Perets, Yulia; Matzui, Lyudmila; Vovchenko, Lyudmila; Ovsiienko, Irina; Yakovenko, Olena; Lazarenko, Oleksandra; Zhuravkov, Alexander; Brusylovets, Oleksii

    2016-08-01

    In the present work, we have investigated concentration and temperature dependences of electrical conductivity of graphite nanoplatelets/epoxy resin composites. The content of nanocarbon filler is varied from 0.01 to 0.05 volume fraction. Before incorporation into the epoxy resin, the graphite nanoplatelets were subjected to ultraviolet ozone treatment at 20-min ultraviolet exposure. The electric resistance of the samples was measured by two- or four-probe method and teraohmmeter E6-13. Several characterization techniques were employed to identify the mechanisms behind the improvements in the electrical properties, including SEM and FTIR spectrum analysis.

  2. Effects of pulp capping materials on fracture resistance of Class II composite restorations

    OpenAIRE

    2015-01-01

    Objective: The aim of this study was to investigate the effect of cavity design and the type of pulp capping materials on the fracture resistance of Class II composite restorations. Materials and Methods: Sixty freshly extracted, sound molar teeth were selected for the study. A dovetail cavity on the mesio-occlusal and a slot cavity on disto-occlusal surfaces of each tooth were prepared, and the teeth were divided 4 groups which one of them as a control group. The pulp capping materials (Ther...

  3. White-light-controlled resistive switching chearacteristics of TiO2/Cu2O composite nanorods array

    Science.gov (United States)

    Sun, Bai; Liu, Yonghong; Lou, Fangming; Chen, Peng

    2015-08-01

    TiO2/Cu2O composite nanorods array were grown on fluorine-doped tin oxide (FTO) substrate by hydrothermal process, and white-light-controlled resistive switching characteristics of Ag/[TiO2/Cu2O]/FTO structure were further investigated. The current-voltage characteristics of the composite nanorods array represent a good rectifying property and bipolar resistive switching behavior. Specially, the resistive switching behavior can be regulated by white-light illuminating at room temperature. This study is helpful for exploring the memory materials and their applications in nonvolatile light-controlled memory devices.

  4. Resistance of composite and amalgam core foundations retained with and without pins and bonding agents.

    Science.gov (United States)

    Imbery, Terence A; Swigert, Ryan; Richman, Brian; Sawicki, Vincent; Pace, Lauren; Moon, Peter C

    2010-01-01

    To compare the resistance of different amalgam and composite core foundations retained by pins, bonding agents, or both, 100 molars were mounted in acrylic resin and their occlusal surfaces were reduced to expose dentin. Pins were inserted at the four line angles of the teeth and matrices were placed. Bonding agents were applied according to the manufacturers' instructions. Amalgam was handcondensed and composite was incrementally added and photocured. Restorations were adjusted to produce specimens (n = 10) 5 mm in height with a 1 mm bevel at the axial-occlusal surface. After immersion in deionized water for 24 hours, specimens were loaded at a 45 degree angle on their beveled surfaces in a Universal Testing Machine at a crosshead speed of 0.02 in./minute. ANOVA and Tukey's tests indicated that FluoroCore 2 (with or without pins) was statistically stronger than all other combinations (p < 0.05).

  5. Examining of abrasion resistance of hybrid composites reinforced with SiC and Cgr particles

    Directory of Open Access Journals (Sweden)

    M. Łągiewka

    2008-08-01

    Full Text Available The presented work discusses the influence of the type and volume percentage of particulate reinforcement consisting of mixed silicon carbide and graphite on the abrasion wear of hybrid composites with AlMg10 matrix. Also the macro photos of frictional surfaces have been shown and the results of hardness measurements have been presented. The performed examinations have allowed for stating that the mixture of SiC and Cgr particles changes in favour the tribological properties of the matrix alloy. It has been also proved that introducing hard reinforcing particles along with soft lubricating ones allows for achieving the material exhibiting high abrasion resistance, and moreover, the graphite particles protect the abraded surface from the destructive action of silicon carbide particles. Also hardness measurements have been performed and the resulting conclusion is that the composite hardness increases with an increase in volume fraction of the reinforcing particles.

  6. Wear resistance analysis of the aluminum 7075 alloy and the nanostructured aluminum 7075 - silver nanoparticles composites

    Directory of Open Access Journals (Sweden)

    Estrada-Ruiz R.H.

    2016-01-01

    Full Text Available Nanostructured composites of the aluminum 7075 alloy and carbon-coated silver nanoparticles were synthetized by the mechanical milling technique using a high-energy mill SPEX 8000M; the powders generated were compacted, sintered and hot-extruded to produce 1 cm-diameter bars. The composites were then subjected to a wear test using a pin-on-disc device to validate the hypothesis that second phase-ductile nanometric particles homogenously distributed throughout the metalmatrix improve the wear resistance of the material. It was found that silver nanoparticles prevent the wear of the material by acting as an obstacle to dislocations movement during the plastic deformation of the contact surface, as well as a solid lubricant when these are separated from the metal-matrix.

  7. WATER RESISTANCE OF WOOD - PLASTIC COMPOSITES MADE FROM WASTE MATERIALS RESULTED IN THE FURNITURE MANUFACTURING PROCESS

    Directory of Open Access Journals (Sweden)

    Camelia COŞEREANU

    2014-12-01

    Full Text Available The purpose of this paper is to present innovative wood-plastic composites made from waste materials such as ABS (acrylonitrile butadiene styrene and wood shavings resulted in the furniture manufacturing process. From previous investigations (with regard to physical integrity and compactness of the panels, only mixtures ranging from a ratio of 100% ABS: 0% shavings to 80% ABS: 20% shavings were selected for water resistance testing. Swelling in thickness and water absorption for 2h and 24h were determined for the proposed wood-plastic composites. The results have shown that only a participation of up to 10% of wood shavings in the tested panels conducted to a good performance

  8. Structure, morphology and corrosion resistance of Ni–Mo+PTh composite coatings

    Indian Academy of Sciences (India)

    J Niedbała

    2015-06-01

    Ni–Mo+PTh composite coatings were prepared from nickel–molybdenum galvanic bath with the addition of thiophene (Th) and HClO4 as result of two processes: induced Ni–Mo alloy deposition and PTh polymerization. A scanning electron microscope was used for surface morphology characterization of the coatings. The Scanning ElectrochemicalWorkstationM370 was used to the surface map of the tested composite coatings. The chemical composition of the coatings was determined by the energy-dispersive spectroscopy (EDS) method. It was stated that the surface of the coatings are characterized by the presence of Ni–Mo particles and polythiophene agglomerates. Electrochemical corrosion investigations of coatings were carried out in the 5 M KOH solution, using voltammetry and electrochemical impedance spectroscopy (EIS) methods. On the basis of these research works it was found that the composite Ni–Mo+PTh coatings are more corrosion resistant in alkaline solution than Ni–Mo. The reasons for this are the presence of the polymer on the surface of the coatings and a decrease of corrosion active surface area of the coatings.

  9. Electrical Resistance of SiC/SiC Ceramic Matrix Composites for Damage Detection and Life-Prediction

    Science.gov (United States)

    Smith, Craig; Morscher, Gregory; Xia, Zhenhai

    2009-01-01

    Ceramic matrix composites (CMC) are suitable for high temperature structural applications such as turbine airfoils and hypersonic thermal protection systems due to their low density high thermal conductivity. The employment of these materials in such applications is limited by the ability to accurately monitor and predict damage evolution. Current nondestructive methods such as ultrasound, x-ray, and thermal imaging are limited in their ability to quantify small scale, transverse, in-plane, matrix cracks developed over long-time creep and fatigue conditions. CMC is a multifunctional material in which the damage is coupled with the material s electrical resistance, providing the possibility of real-time information about the damage state through monitoring of resistance. Here, resistance measurement of SiC/SiC composites under mechanical load at both room temperature monotonic and high temperature creep conditions, coupled with a modal acoustic emission technique, can relate the effects of temperature, strain, matrix cracks, fiber breaks, and oxidation to the change in electrical resistance. A multiscale model can in turn be developed for life prediction of in-service composites, based on electrical resistance methods. Results of tensile mechanical testing of SiC/SiC composites at room and high temperatures will be discussed. Data relating electrical resistivity to composite constituent content, fiber architecture, temperature, matrix crack formation, and oxidation will be explained, along with progress in modeling such properties.

  10. In Situ Synthesis of Reduced Graphene Oxide-Reinforced Silicone-Acrylate Resin Composite Films Applied in Erosion Resistance

    Directory of Open Access Journals (Sweden)

    Yang Cao

    2015-01-01

    Full Text Available The reduced graphene oxide reinforced silicone-acrylate resin composite films (rGO/SAR composite films were prepared by in situ synthesis method. The structure of rGO/SAR composite films was characterized by Raman spectrum, atomic force microscope, scanning electron microscopy, and thermogravimetric analyzer. The results showed that the rGO were uniformly dispersed in silicone-acrylate resin matrix. Furthermore, the effect of rGO loading on mechanical properties of composite films was investigated by bulge test. A significant enhancement (ca. 290% and 320% in Young’s modulus and yield stress was obtained by adding the rGO to silicone-acrylate resin. At the same time, the adhesive energy between the composite films and metal substrate was also improved to be about 200%. Moreover, the erosion resistance of the composite films was also investigated as function of rGO loading. The rGO had great effect on the erosion resistance of the composite films, in which the Rcorr (ca. 0.8 mm/year of composite film was far lower than that (28.7 mm/year of pure silicone-acrylate resin film. Thus, this approach provides a novel route to investigate mechanical stability of polymer composite films and improve erosion resistance of polymer coating, which are very important to be used in mechanical-corrosion coupling environments.

  11. Study on dry friction and wear resistance of a WC-Co particle reinforced iron matrix composite material

    Directory of Open Access Journals (Sweden)

    Zhang Peng

    2013-05-01

    Full Text Available In order to select a suitable material for the rolling mill guide application, the dry sliding friction and wear resistance of a tungsten carbide combining cobalt (WC-Co particle reinforced chromium cast iron composite material were studied. In particular, the wear resistance was discussed in detail. The results showed that the composite material demonstrates 25 times the wear resistance of high Cr cast iron, and 9 times the wear resistance of heat resistant steel. However, the average friction factor in the stable friction stage showed a relationship of μComposites/45 # steel > μHigh chromium cast iron/45 # steel > μHeat resistant steel/45 # steel. The wear resistance mechanism of the composite material was associated with the reinforcing particles, which protruded from the worn surface to bear the friction load when the matrix material surface was worn, thereby reducing the abrasive and adhesive wear. In addition, the matrix material possessed suitable hardness and toughness, providing a support to the reinforcements.

  12. Numerical modeling of mechanical behavior of multilayered composite plates with defects under static loading

    Science.gov (United States)

    Korepanov, V. V.; Serovaev, G. S.

    2017-06-01

    Evaluation of the mechanical state of a structure or its components in the process of operation based on detection of internal damages (damage detection) becomes especially important in such rapidly developing spheres of production as machine building, aerospace industry, etc. One of the most important features of these industries is the application of new types of materials among which polymer based composite materials occupy a significant position. Hence, they must have sufficient operational rigidity and strength. However, defects of various kinds may arise during the manufacture. Delamination is the most common defect in structures made from composite materials and represents a phenomenon that involves the complex fracture of layers and interlayer compounds. Among the reasons of delamination occurrence are: disposition of anti-adhesive lubricants, films; insufficient content of binder, high content of volatile elements; violation of the molding regime; poor quality of anti-adhesive coating on the surface of the tooling. One of the effective methods for analyzing the influence of defects is numerical simulation. With the help of numerical methods, it is possible to track the evolution of various parameters when the defect size and quantity change. In the paper, a multilayered plate of an equally resistant carbon fiber reinforced plastic was considered, with a thickness of each layer equal to 0.2 mm. Various static loading cases are studied: uniaxial tension, three and four-point bending. For each type of loading, a numerical calculation of the stress-strain state was performed for healthy and delaminated plates, with different number and size of the defects. Contact interaction between adjacent surfaces in the zone of delamination was taken into account.

  13. Delamination behaviour in differently copper laminated REBCO coated conductor tapes under transverse loading

    Energy Technology Data Exchange (ETDEWEB)

    Gorospe, Alking [Department of Mechanical Design Engineering, Andong National University, 1375 Kyungdong-Ro, Andong 760-749 (Korea, Republic of); Department of Engineering, Aurora State College of Technology, Baler Aurora 3200 (Philippines); Nisay, Arman [Department of Mechanical Design Engineering, Andong National University, 1375 Kyungdong-Ro, Andong 760-749 (Korea, Republic of); Shin, Hyung-Seop, E-mail: hsshin@andong.ac.kr [Department of Mechanical Design Engineering, Andong National University, 1375 Kyungdong-Ro, Andong 760-749 (Korea, Republic of)

    2014-09-15

    Highlights: • I{sub c} degradation behavior under transverse tension loading in different CC tape structure. • Weibull distribution analysis applied on delamination mechanism of CC tape. • Delamination mechanism on CC tapes depending on copper lamination type. • SEM and WDS mapping analysis of delamination sites under transverse loading. - Abstract: Laminated HTS coated conductor (CC) tapes having a unique multi-layer structure made them vulnerable when exposed to transverse loading. Electromechanical transport properties of these CC tapes can be affected by excessive transverse stresses. Due to the coefficient of thermal expansion (CTE) mismatch and incompatibility among constituent materials used in coil applications, delamination among layers occurs and causes critical current, I{sub c} degradation in the CC tapes. In this study, the delamination behaviors in copper (Cu) solder-laminated CC tapes by soldering and surround Cu-stabilized ones by electroplating under transverse tension loading were investigated. Similarly to the surround Cu-stabilized CC tapes in our previous reports, the Cu solder-laminated CC tapes also showed an abrupt and gradual I{sub c} degradation behavior. However, the Cu solder-laminated CC tapes showed different delamination morphologies as compared to the surround Cu-stabilized CC tapes; the superconducting side and the substrate side of the Cu solder laminated CC tapes were totally separated by delamination. On the other hand, the brass laminate did not show any significant effect on the delamination strength when it is added upon the surround Cu-stabilized CC tapes.

  14. Energy based study of quasi-static delamination as a low cycle fatigue process

    NARCIS (Netherlands)

    Amaral, L.; Yao, L.; Alderliesten, R.C.; Benedictus, R.

    2015-01-01

    This work proposes to treat quasi-static mode I delamination growth of CFRP as a low-cycle fatigue process. To this end, mode I quasi-static and fatigue delamination tests were performed. An average physical Strain Energy Release Rate (SERR), derived from an energy balance, is used to characterize t

  15. Cathodic delamination: Quantification of ionic transport rates along coating-steel interfaces

    DEFF Research Database (Denmark)

    Sørensen, P.A.; Dam-Johansen, Kim; Weinell, C.E.

    2010-01-01

    and Fick's second law, under the assumption of a transport-controlled mechanism, show qualitative agreement with the observed delamination rates in 0.5 M sodium chloride. This confirms that the rate-determining step of cathodic delamination is the transport of sodium ions along the coating-steel interface....

  16. Cathodic delamination: Quantification of ionic transport rates along coating-steel interfaces

    DEFF Research Database (Denmark)

    Sørensen, Per Aggerholm; Dam-Johansen, Kim; Erik Weinell, Claus

    2010-01-01

    and Fick's second law, under the assumption of a transport controlled mechanism, show qualitative agreement with the observed delamination rates in 0.5 M sodium chloride. This confirms that the rate-determining step of cathodic delamination is the transport of sodium ions along the coating-steel interface...

  17. Work of adhesion in laser-induced delamination along polymer-metal interfaces

    NARCIS (Netherlands)

    Fedorov, A.; van Tijum, R.; Vellinga, W. P.; de Hosson, Jeff

    2007-01-01

    Laser-induced delamination is a recent technique aimed at characterizing adhesive strength of thin polymer coatings on metal substrates. A laser pulse is used to create a blister that initiates further delamination of the film under pressure. To process the experimental data a simple elastic model w

  18. Reliability at the Chip Interfaces: Delaminating the Silicon Die from Molding Compound

    NARCIS (Netherlands)

    Schlottig, G.

    2012-01-01

    This book describes a setup that allows to delaminate the Silicon-to-Molding Compound interface for obtaining interfacial fracture parameters: the Mixed Mode Chisel setup (MMC). With this device for the first time the delamination can be initiated and propagated, while preventing the occurrence of r

  19. Reliability at the Chip Interfaces: Delaminating the Silicon Die from Molding Compound

    NARCIS (Netherlands)

    Schlottig, G.

    2012-01-01

    This book describes a setup that allows to delaminate the Silicon-to-Molding Compound interface for obtaining interfacial fracture parameters: the Mixed Mode Chisel setup (MMC). With this device for the first time the delamination can be initiated and propagated, while preventing the occurrence of r

  20. Energy based study of quasi-static delamination as a low cycle fatigue process

    NARCIS (Netherlands)

    Amaral, L.; Yao, L.; Alderliesten, R.C.; Benedictus, R.

    2015-01-01

    This work proposes to treat quasi-static mode I delamination growth of CFRP as a low-cycle fatigue process. To this end, mode I quasi-static and fatigue delamination tests were performed. An average physical Strain Energy Release Rate (SERR), derived from an energy balance, is used to characterize

  1. Development and Application of Benchmark Examples for Mode II Static Delamination Propagation and Fatigue Growth Predictions

    Science.gov (United States)

    Krueger, Ronald

    2011-01-01

    The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

  2. Development of Benchmark Examples for Quasi-Static Delamination Propagation and Fatigue Growth Predictions

    Science.gov (United States)

    Krueger, Ronald

    2012-01-01

    The development of benchmark examples for quasi-static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for Abaqus/Standard. The example is based on a finite element model of a Double-Cantilever Beam specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, a quasi-static benchmark example was created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with choosing the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall the results are encouraging, but further assessment for mixed-mode delamination is required.

  3. Development of Benchmark Examples for Delamination Onset and Fatigue Growth Prediction

    Science.gov (United States)

    Krueger, Ronald

    2011-01-01

    An approach for assessing the delamination propagation and growth capabilities in commercial finite element codes was developed and demonstrated for the Virtual Crack Closure Technique (VCCT) implementations in ABAQUS. The Double Cantilever Beam (DCB) specimen was chosen as an example. First, benchmark results to assess delamination propagation capabilities under static loading were created using models simulating specimens with different delamination lengths. For each delamination length modeled, the load and displacement at the load point were monitored. The mixed-mode strain energy release rate components were calculated along the delamination front across the width of the specimen. A failure index was calculated by correlating the results with the mixed-mode failure criterion of the graphite/epoxy material. The calculated critical loads and critical displacements for delamination onset for each delamination length modeled were used as a benchmark. The load/displacement relationship computed during automatic propagation should closely match the benchmark case. Second, starting from an initially straight front, the delamination was allowed to propagate based on the algorithms implemented in the commercial finite element software. The load-displacement relationship obtained from the propagation analysis results and the benchmark results were compared. Good agreements could be achieved by selecting the appropriate input parameters, which were determined in an iterative procedure.

  4. Development of Benchmark Examples for Static Delamination Propagation and Fatigue Growth Predictions

    Science.gov (United States)

    Kruger, Ronald

    2011-01-01

    The development of benchmark examples for static delamination propagation and cyclic delamination onset and growth prediction is presented and demonstrated for a commercial code. The example is based on a finite element model of an End-Notched Flexure (ENF) specimen. The example is independent of the analysis software used and allows the assessment of the automated delamination propagation, onset and growth prediction capabilities in commercial finite element codes based on the virtual crack closure technique (VCCT). First, static benchmark examples were created for the specimen. Second, based on the static results, benchmark examples for cyclic delamination growth were created. Third, the load-displacement relationship from a propagation analysis and the benchmark results were compared, and good agreement could be achieved by selecting the appropriate input parameters. Fourth, starting from an initially straight front, the delamination was allowed to grow under cyclic loading. The number of cycles to delamination onset and the number of cycles during stable delamination growth for each growth increment were obtained from the automated analysis and compared to the benchmark examples. Again, good agreement between the results obtained from the growth analysis and the benchmark results could be achieved by selecting the appropriate input parameters. The benchmarking procedure proved valuable by highlighting the issues associated with the input parameters of the particular implementation. Selecting the appropriate input parameters, however, was not straightforward and often required an iterative procedure. Overall, the results are encouraging but further assessment for mixed-mode delamination is required.

  5. Cotton fabric with plasma pretreatment and ZnO/Carboxymethyl chitosan composite finishing for durable UV resistance and antibacterial property.

    Science.gov (United States)

    Wang, Chunxia; Lv, Jingchun; Ren, Yu; Zhou, Qingqing; Chen, Jiayi; Zhi, Tian; Lu, Zhenqian; Gao, Dawei; Ma, Zhipeng; Jin, Limin

    2016-03-15

    ZnO/carboxymethyl chitosan (ZnO/CMCS) composite was prepared and confirmed by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Ultraviolet-visible (UV-vis) spectroscopy, Scanning electron microscope (SEM), Transmission electron microscope (TEM). The combination of plasma pretreatment and ZnO/CMCS composite finishing was applied to provide durable UV resistance and antibacterial activity for cotton fabric. Cotton fabric was pretreated by cold oxygen plasma and the ZnO/CMCS composite finishing was carried out by pad-dry-cure. Cotton fabric was characterized by SEM, FTIR, UV resistance, antibacterial activity and Thermogravimetry (TG). SEM and FTIR analysis demonstrated the presence of ZnO/CMCS composite on cotton fabric and the increasing loading efficiency of ZnO/CMCS composite owing to plasma treatment. UV resistance and antibacterial activity of the finished cotton fabric were greatly improved, which increased with the increasing concentration of ZnO/CMCS composite. TG analysis indicated that the combined finishing of cotton fabric with plasma pretreatment and ZnO/CMCS composite could improve its thermal property. The finished cotton fabric exhibited an excellent laundering durability in UV resistance and antibacterial activity.

  6. Resistance of Phosphogypsum Cement Pozzolanic Compositions against the Influence of Water

    Directory of Open Access Journals (Sweden)

    Sergejus GAIDUČIS

    2011-09-01

    Full Text Available The reprocessing of freshly removed extractive hemihydrate phosphogypsum into hydraulic composite phosphogypsum cement pozzolana (PGCP binder using mechanical activation is analyzed in this work. In order to increase the effectiveness of the dealing with phosphogypsum reprocessing problem and to lower the energy consumption required for the production of binding materials from phosphogypsum, physical mechanical and water resistance properties of the PGCP binder with less amount (10 % of cement (PGCP(10 were analyzed and compared with the properties of conventional PGCP binder, where the amount of cement is 20 % (PGCP(20. The PGCP binder with pozzolana additives of two types - carbonate opoka and microsilica are analysed. Fresh wet hemihydrate phosphogypsum, cement and pozzolana additive were mechanically activated together and from resulting mixture the samples were formed by vibrating. Compressive strength of PGCP(10 samples after 28 days was 26 MPa - 29 MPa, after 4 months - 30 MPa - 32 MPa, PGCP(20 - 32 MPa - 35 MPa and 36 MPa - 42 MPa accordingly. It is found, that hardened PGCP(10 are also quite resistant to short-term (2 days impact of water (softening coefficient was 0.91 - 0.94, however, its resistance to long-term impact of water is significantly less than PGCP(20. PGCP with microsilica is more strength and more resistant to impact of water than PGCP with opoka. Both, PGCP with opoka, as well as the ones with microsilica, are resistant to the formation of ettringite. However, the primary ettringite and high amount of carbonates, found in the PGCP with opoka, stimulates the formation of thaumasite at low positive temperature and humidity.http://dx.doi.org/10.5755/j01.ms.17.3.599

  7. Spatio-Temporal Variation in Landscape Composition May Speed Resistance Evolution of Pests to Bt Crops

    Science.gov (United States)

    Ives, Anthony R.; Paull, Cate; Hulthen, Andrew; Downes, Sharon; Andow, David A.; Haygood, Ralph; Zalucki, Myron P.; Schellhorn, Nancy A.

    2017-01-01

    Transgenic crops that express insecticide genes from Bacillus thuringiensis (Bt) are used worldwide against moth and beetle pests. Because these engineered plants can kill over 95% of susceptible larvae, they can rapidly select for resistance. Here, we use a model for a pyramid two-toxin Bt crop to explore the consequences of spatio-temporal variation in the area of Bt crop and non-Bt refuge habitat. We show that variability over time in the proportion of suitable non-Bt breeding habitat, Q, or in the total area of Bt and suitable non-Bt habitat, K, can increase the overall rate of resistance evolution by causing short-term surges of intense selection. These surges can be exacerbated when temporal variation in Q and/or K cause high larval densities in refuges that increase density-dependent mortality; this will give resistant larvae in Bt fields a relative advantage over susceptible larvae that largely depend on refuges. We address the effects of spatio-temporal variation in a management setting for two bollworm pests of cotton, Helicoverpa armigera and H. punctigera, and field data on landscape crop distributions from Australia. Even a small proportion of Bt fields available to egg-laying females when refuges are sparse may result in high exposure to Bt for just a single generation per year and cause a surge in selection. Therefore, rapid resistance evolution can occur when Bt crops are rare rather than common in the landscape. These results highlight the need to understand spatio-temporal fluctuations in the landscape composition of Bt crops and non-Bt habitats in order to design effective resistance management strategies. PMID:28046073

  8. Spatio-Temporal Variation in Landscape Composition May Speed Resistance Evolution of Pests to Bt Crops.

    Science.gov (United States)

    Ives, Anthony R; Paull, Cate; Hulthen, Andrew; Downes, Sharon; Andow, David A; Haygood, Ralph; Zalucki, Myron P; Schellhorn, Nancy A

    2017-01-01

    Transgenic crops that express insecticide genes from Bacillus thuringiensis (Bt) are used worldwide against moth and beetle pests. Because these engineered plants can kill over 95% of susceptible larvae, they can rapidly select for resistance. Here, we use a model for a pyramid two-toxin Bt crop to explore the consequences of spatio-temporal variation in the area of Bt crop and non-Bt refuge habitat. We show that variability over time in the proportion of suitable non-Bt breeding habitat, Q, or in the total area of Bt and suitable non-Bt habitat, K, can increase the overall rate of resistance evolution by causing short-term surges of intense selection. These surges can be exacerbated when temporal variation in Q and/or K cause high larval densities in refuges that increase density-dependent mortality; this will give resistant larvae in Bt fields a relative advantage over susceptible larvae that largely depend on refuges. We address the effects of spatio-temporal variation in a management setting for two bollworm pests of cotton, Helicoverpa armigera and H. punctigera, and field data on landscape crop distributions from Australia. Even a small proportion of Bt fields available to egg-laying females when refuges are sparse may result in high exposure to Bt for just a single generation per year and cause a surge in selection. Therefore, rapid resistance evolution can occur when Bt crops are rare rather than common in the landscape. These results highlight the need to understand spatio-temporal fluctuations in the landscape composition of Bt crops and non-Bt habitats in order to design effective resistance management strategies.

  9. Improved biomechanical resistance using an expanded polytetrafluoroethylene composite-structure prosthesis.

    Science.gov (United States)

    Bellón, Juan M; Rodríguez, Marta; Serrano, Natalia; San-Martín, Antonio Carrera; Buján, Julia

    2004-05-01

    We designed a composite-structure (laminar-reticular) prosthesis using expanded polytetrafluoroethylene (ePTFE) as the biomaterial in an attempt to improve the biomechanical resistance of the same biomaterial in the form of a single lamina. Defects (7 x 5 cm) were created in the abdominal wall of male white New Zealand rabbits (n = 24). The defects, which comprised all the wall layers except the skin, were then repaired with one of two types of ePTFE prosthesis. One was a latest generation laminar prosthesis (DualMesh, or Gore-Tex) and the other was a composite of in-house design (CV-4 mesh composite) made by suturing a mesh woven out of ePTFE thread to an ePTFE lamina. After sacrificing the animals at 14 or 90 days after surgery, implant specimens were subjected to morphologic analysis (light microscopy and scanning electron microscopy); and adhesion formation, neoperitoneal thickness, and biomechanical strength were evaluated. No significant differences were recorded between the two prosthesis regarding the consistency of adhesions or the area occupied by adhesions (DM 0.17 +/- 0.06; CV-4 mesh composite 0.18 +/- 0.08 cm2) (p > 0.05). Notably, improved tissue integration was achieved using the composite prosthesis; its reticular side became infiltrated by dense connective tissue that enveloped the mesh filaments. In contrast, the DM prosthesis became encapsulated by host tissue. The neoperitoneum induced by both prostheses was homogeneous and orderly, with a layer of typical mesothelial cells lining its inner surface. The thickness of the neoperitoneum was similar (p > 0.05) for the two implants (385.0 +/- 3.4 vs. 390 +/- 3.1 microm), although significantly higher (p < 0.05) mechanical resistance values were recorded for the composite prosthesis (26.75 +/- 3.71 vs. 14.11 +/- 3.71 N). Our findings suggest that the use of a reticular and a laminar ePTFE layer in the same prosthesis leads to better repair and biomechanical behavior compared to the use of a single

  10. Study of multilayer packaging delamination mechanisms using different surface analysis techniques

    Energy Technology Data Exchange (ETDEWEB)

    Garrido-Lopez, Alvaro [Department of Chemistry, University of La Rioja, C/Madre de Dios 51, E-26006 Logrono, La Rioja (Spain); Tena, Maria Teresa, E-mail: maria-teresa.tena@unirioja.es [Department of Chemistry, University of La Rioja, C/Madre de Dios 51, E-26006 Logrono, La Rioja (Spain)

    2010-04-01

    Multilayer packaging, consisting of different layers joined by using an adhesive or an extrusion process, is widely used to promote different products, such as food, cosmetics, etc. The main disadvantage in using this form of packaging is the delamination process. In this work, different surface techniques (X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectroscopy and attenuated total reflection Fourier transform infrared spectroscopy) are used to analyse the delaminated surfaces in order to study the mechanisms that cause delamination of multilayer packaging. According to our results, the reaction of migrated molecules with adhesive-aluminium bonds is the main cause of the chemical delamination process. In contrast, the delamination of extruded materials would seem to be caused by the breaking of Van der Waals bonds.

  11. The interplay of crack hopping, delamination and interface failure in drying nanoparticle films

    Science.gov (United States)

    Yang, Bin; Sharp, James S.; Smith, Mike I.

    2016-08-01

    Films formed through the drying of nanoparticle suspensions release the build-up of strain through a variety of different mechanisms including shear banding, crack formation and delamination. Here we show that important connections exist between these different phenomena: delamination depends on the dynamics of crack hopping, which in turn is influenced by the presence of shear bands. We also show that delamination does not occur uniformly across the film. As cracks hop they locally initiate the delamination of the film which warps with a timescale much longer than that associated with the hopping of cracks. The motion of a small region of the delamination front, where the shear component of interfacial crack propagation is believed to be enhanced, results in the deposition of a complex zig-zag pattern on the supporting substrate.

  12. Improving Corrosion Resistance of Cf/Mg Composites using Rare Earth Conversion Coatings

    Institute of Scientific and Technical Information of China (English)

    Song Meihui; Wang Chunyu; Wu Gaohui

    2007-01-01

    The surface of carbon fiber reinforced Mg matrix (Cf/Mg) composites was modified by treatment of rare earth conversion coating, and nontoxic, non-pollution Ce conversion coatings were prepared. The effect of the coatings on corrosion behaviors of composites was investigated by electrochemical polarization technology and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. The higher Ecorr and lower icorr were obtained by Ce conversion coatings. EIS results showed that the higher values of R2 were obtained by treatment containing CeCl3, the high corrosion resistance occured in treatment containing CeCl3, the low corrosion resistance in uncoating sample, the coating of treatment containing Ce(NO3)3 was medium. The microstructure of Ce conversion coatings was observed by scanning electron microscopy (SEM), and the elements of corresponding for coatings was characterized by energy dispersive spectrometer (EDS). The micro-cracks and Ce-riched spherical particles were characteristics of these coatings.

  13. TiO2-TiO2 composite resistive humidity sensor: ethanol crosssensitivity

    Science.gov (United States)

    Ghalamboran, Milad; Saedi, Yasin

    2016-03-01

    The fabrication method and characterization results of a TiO2-TiO2 composite bead used for humidity sensing along with its negative cross-sensitivity to ethanol vapor are reported. The bead shaped resistive sample sensors are fabricated by the drop-casting of a TiO2 slurry on two Pt wire segments. The dried bead is pre-fired at 750°C and subsequently impregnated with a Ti-based sol. The sample is ready for characterization after a thermal annealing at 600°C in air. Structurally, the bead is a composite of the micron-sized TiO2 crystallites embedded in a matrix of nanometric TiO2 particle aggregates. The performance of the beads as resistive humidity sensors is recorded at room temperature in standard humidity level chambers. Results evince the wide dynamic range of the sensors fabricated in the low relative humidity range. While the sensor conductance is not sensitive to ethanol vapor in dry air, in humid air, sensor's responses are negatively affected by the contaminant.

  14. Resistivity and low-frequency noise characteristics of epoxy-carbon composites

    Science.gov (United States)

    PralgauskaitÄ--, Sandra; Matukas, Jonas; Tretjak, Marina; Macutkevic, Jan; Banys, Juras; Selskis, Algirdas; Cataldo, Antonino; Micciulla, Federico; Bellucci, Stefano; Fierro, Vanessa; Celzard, Alain

    2017-03-01

    Noise and electrical transport properties of composites based on epoxy resin filled with various carbon inclusions (single-walled carbon nanotubes, high surface area carbon black, and exfoliated graphite) were investigated in depth. The temperature dependence of resistivity shows that Mott's hopping and tunneling between conductive carbon particles dominate the charge carrier transport at low temperature, whereas a positive temperature coefficient effect occurs at higher temperature. Low-frequency noise spectra of the investigated materials comprise 1/fα type components. The noise level is the highest for composites close to the percolation threshold. The percolation threshold value of the system also strongly impacts both the temperature dependence of the noise level and the resistivity. Close to the percolation threshold, the noise level increases due to the carrier tunneling throughout the polymer matrix and decreases due to the rapid expansion of the polymer matrix. In contrast, the latter has almost no influence on the noise level far above the percolation threshold, and the small kink in the temperature dependence of the noise level indicates a crossover between tunneling and thermally activated electron transport mechanisms.

  15. Impact of Resistance Circuit Training on Neuromuscular, Cardiorespiratory and Body Composition Adaptations in the Elderly

    Science.gov (United States)

    Romero-Arenas, Salvador; Martínez-Pascual, Miryam; Alcaraz, Pedro E.

    2013-01-01

    Declines in maximal aerobic power and skeletal muscle force production with advancing age are examples of functional declines with aging, which can severely limit physical performance and independence, and are negatively correlated with all cause mortality. It is well known that both endurance exercise and resistance training can substantially improve physical fitness and health-related factors in older individuals. Circuit-based resistance training, where loads are lifted with minimal rest, may be a very effective strategy for increasing oxygen consumption, pulmonary ventilation, strength, and functional capacity while improving body composition. In addition, circuit training is a time-efficient exercise modality that can elicit demonstrable improvements in health and physical fitness. Hence, it seems reasonable to identify the most effective combination of intensity, volume, work to rest ratio, weekly frequency and exercise sequence to promote neuromuscular, cardiorespiratory and body composition adaptations in the elderly. Thus, the purpose of this review was to summarize and update knowledge about the effects of circuit weight training in older adults and elderly population, as a starting point for developing future interventions that maintain a higher quality of life in people throughout their lifetime. PMID:24124631

  16. N-stearoylethanolamine restores pancreas lipid composition in obesity-induced insulin resistant rats.

    Science.gov (United States)

    Onopchenko, Oleksandra V; Kosiakova, Galina V; Oz, Murat; Klimashevsky, Vitaliy M; Gula, Nadiya M

    2015-01-01

    This study investigates the protective effect of N-stearoylethanolamine (NSE), a bioactive N-acylethanolamine , on the lipid profile distribution in the pancreas of obesity-induced insulin resistant (IR) rats fed with prolonged high fat diet (58% of fat for 6 months). The phospholipid composition was determined using 2D thin-layer chromatography. The level of individual phospholipids was estimated by measuring inorganic phosphorus content. The fatty acid (FA) composition and cholesterol level were investigated by gas-liquid chromatography. Compared to controls, plasma levels of triglycerides and insulin were significantly increased in IR rats. The pancreas lipid composition indicated a significant reduction of the free cholesterol level and some phospholipids such as phosphatidylcholine (PtdCho), phosphatidylethanolamine (PtdEtn), phosphatidylinositol (PtdIns), phosphatidylserine (PtdSer) compared to controls. Moreover, the FA composition of pancreas showed a significant redistribution of the main FA (18:1n-9, 18:2n-6, 18:3n-6 and 20:4n-6) levels between phospholipid, free FA, triglyceride fractions under IR conditions that was accompanied by a change in the estimated activities of Δ9-, Δ6-, Δ5-desaturase. Administration of N-stearoylethanolamine (NSE, 50 mg/kg daily per os for 2 weeks) IR rats triggered an increase in the content of free cholesterol, PtdCho and normalization of PtdEtn, PtdSer level. Furthermore, the NSE modulated the activity of desaturases, thus influenced FA composition and restored the FA ratios in the lipid fractions. These NSE-induced changes were associated with a normalization of plasma triglyceride content, considerable decrease of insulin and index HOMA-IR level in rats under IR conditions.

  17. Non-Magnetic, Tough, Corrosion- and Wear-Resistant Knives From Bulk Metallic Glasses and Composites

    Science.gov (United States)

    Hoffman, Douglas C.; Potter, Benjamin

    2013-01-01

    Quality knives are typically fabricated from high-strength steel alloys. Depending on the application, there are different requirements for mechanical and physical properties that cause problems for steel alloys. For example, diver's knives are generally used in salt water, which causes rust in steel knives. Titanium diver's knives are a popular alternative due to their salt water corrosion resistance, but are too soft to maintain a sharp cutting edge. Steel knives are also magnetic, which is undesirable for military applications where the knives are used as a tactical tool for diffusing magnetic mines. Steel is also significantly denser than titanium (8 g/cu cm vs. 4.5 g/cu cm), which results in heavier knives for the same size. Steel is hard and wear-resistant, compared with titanium, and can keep a sharp edge during service. A major drawback of both steel and titanium knives is that they must be ground or machined into the final knife shape from a billet. Since most knives have a mirrored surface and a complex shape, manufacturing them is complex. It would be more desirable if the knife could be cast into a net or near-net shape in a single step. The solution to the deficiencies of titanium, steel, and ceramic knives is to fabricate them using bulk metallic glasses (or composites). These alloys can be cast into net or near-net shaped knives with a combination of properties that exceed both titanium and steel. A commercially viable BMG (bulk metallic glass) or composite knife is one that exhibits one or all of the following properties: It is based on titanium, has a self-sharpening edge, can retain an edge during service, is hard, is non-magnetic, is corrosion-resistant against a variety of corrosive environments, is tough (to allow for prying), can be cast into a net-shape with a mirror finish and a complex shape, has excellent wear resistance, and is low-density. These properties can be achieved in BMG and composites through alloy chemistry and processing. For

  18. Determination of a cohesive law for delamination modelling - Accounting for variation in crack opening and stress state across the test specimen width

    DEFF Research Database (Denmark)

    Joki, R. K.; Grytten, F.; Hayman, Brian

    2016-01-01

    -scale bridging and the multi-axial state of stress in the test specimen. The fracture resistance is calculated from the applied moments, the elastic material properties and the geometry of the test specimen. The cohesive law is then determined in a three step procedure: 1) Obtain the bridging law...... that the changing state of stress and deformation across the width of the test specimen is taken into account. The changing state of stress and deformation across the specimen width is shown to be significant for small openings (small fracture process zone size). This will also be important for the initial part......The cohesive law for Mode I delamination in glass fibre Non-Crimped Fabric reinforced vinylester is determined for use in finite element models. The cohesive law is derived from a delamination test based on DCB specimens loaded with pure bending moments taking into account the presence of large...

  19. Electrical resistance stability of high content carbon fiber reinforced cement composite

    Institute of Scientific and Technical Information of China (English)

    YANG Zai-fu; TANG Zu-quan; LI Zhuo-qiu; QIAN Jue-shi

    2005-01-01

    The influences of curing time, the content of free evaporable water in cement paste, environmental temperature, and alternative heating and cooling on the electrical resistance of high content carbon fiber reinforced cement (CFRC) paste are studied by experiments with specimens of Portland cement 42.5 with 10 mm PAN-based carbon fiber and methylcellulose. Experimental results indicate that the electrical resistance of CFRC increases relatively by 24% within a hydration time of 90 d and almost keeps constant after 14 d, changes hardly with the mass loss of free evaporable water in the concrete dried at 50℃C, increases relatively by 4% when ambient temperature decreases from 15℃ to-20℃, and decreases relatively by 13% with temperature increasing by 88℃. It is suggested that the electric resistance of the CFRC is stable, which is testified by the stable power output obtained by electrifying the CFRC slab with a given voltage. This implies that such kind of high content carbon fiber reinforced cement composite is potentially a desirable electrothermal material for airfield runways and road surfaces deicing.

  20. Thickness of CAD-CAM composite resin overlays influences fatigue resistance of endodontically treated premolars.

    Science.gov (United States)

    Magne, Pascal; Knezevic, Alena

    2009-10-01

    Evaluate the influence of composite resin CAD-CAM restoration thickness on the in vitro fatigue resistance and failure mode of overlay-type restoration in endodontically treated premolars. Thirty extracted premolars received root canal treatment followed by a standardized tooth preparation (1.5-, 2.5- or 3.5-mm cusp reduction, proximal gingival margins located 1.5mm below the CEJ, glass-ionomer base and immediately sealed dentin with Optibond FL). Restorations were milled using Cerec3 and FiltekMZ100 composite blocks. The intaglio surfaces of the overlays were sandblasted and silanated. Tooth preparations were sandblasted and etched before insertion of the restoration. All restorations were luted with Optibond FL and preheated FiltekZ100. A closed-loop servohydraulic unit was used for simulating cyclic isometric chewing at 5 Hz, starting with a load of 200 N (5000 cycles), followed by stages of 400, 600, 800, 1000, 1200 and 1400 N at a maximum of 30,000 cycles each. All samples were loaded until fracture or to a maximum of 185,000 cycles. Groups were compared using the Kaplan-Meier survival curves. None of the restored premolars with the 1.5-mm cusp overlap restoration withstood all 185,000 loading cycles. With 2.5- and 3.5-mm cusp overlap, the survival rate was 30% and 40%, respectively. The rate of fracture below the CEJ was 60%, 60% and 30% for 1.5, 2.5 and 3.5 mm of cusp overlap, respectively. Survival of restored premolars with 2.5- and 3.5-mm cusp coverage was not significantly different (p=.23). Thick FiltekMZ100 composite resin onlays showed higher fatigue resistance than thin ones and may be associated with fractures that are less subgingival.

  1. The effects of resistance exercise training on body composition and strength in obese prepubertal children.

    Science.gov (United States)

    Alberga, Angela S; Farnesi, Biagina-Carla; Lafleche, Angele; Legault, Laurent; Komorowski, Joanna

    2013-09-01

    To assess the effects of resistance exercise training on body composition and muscular strength in obese prepubertal children. Study participants, who were between the ages of 8 and 12 years, met Tanner I (stage) criteria, had a body mass index ≥ 95th percentile for age and sex, were randomized to either high-repetition, moderate-intensity resistance training (n = 12) or to the non-intervention control group (n = 7) for 12 weeks. Exercise training was performed twice a week for 75 minutes per session. Body composition was assessed using dual energy x-ray absorptiometry and muscular strength was evaluated using a 1-repetition-maximum test. Exercise-group participants attended 98% of the 24 total sessions and showed a significant increase in body weight (57.6± 13.5 vs 59.6± 14.1 kg), height (144.9± 9 vs 146.6± 10.4 cm), lean body mass (32.6± 6.8 vs 34.0± 7.0 kg), lean body mass index (lean body mass in kg/height2; 15.3± 1.6 vs 15.6± 1.5 kg/m2), arm strength (28.4± 5.8 vs 31.2± 6.0 kg), and leg strength (89.4± 31.7 vs 113.4± 34 2 kg) from baseline measures (P strength. When the changes in participant body composition and muscular strength were compared between the exercise and control groups, significant differences were found in leg lean mass and leg strength (P training increases leg lean mass and leg strength in obese prepubertal youth and may have a positive effect on overall physical activity and health.

  2. Are linear elastic material properties relevant predictors of the cyclic fatigue resistance of dental resin composites?

    Science.gov (United States)

    Belli, Renan; Petschelt, Anselm; Lohbauer, Ulrich

    2014-04-01

    The aim of this study was to measure the linear elastic material properties of direct dental resin composites and correlate them with their fatigue strength under cyclic loading. Bar specimens of twelve resin composites were produced according to ISO 4049 and tested for elastic modulus (Emod) in 3-point bending (n=10), flexural strength (FS) (n=15) and single-edge-notch-beam fracture toughness (FT) (n=15), both in 4-point bending. Using the same specimen geometry, the flexural fatigue strength (FFS) was determined using the staircase approach after 10(4) cycles at 0.5 Hz in 4-point bending (n=25). The observation of the fracture surface and fracture profiles was conducted using a scanning electron microscope in order to evaluate the respective fracture mechanisms according to the two different loading conditions. Materials were ranked differently according to the tested parameters. Only weak correlations were found between any of the initial properties and FFS or strength loss. The best correlation to FFS was found to be the Emod (r(2)=0.679), although only slightly. Crack path in both loading conditions was mainly interparticle, with the crack propagating mainly within the matrix phase for fatigued specimens and eventually through the filler/matrix interface for statically loaded specimens. Fracture of large particles or prepolymerized fillers was only observed in specimens of FS and FT. Initial properties were better associated with microstructural features, whereas the fatigue resistance showed to be more dependent on aspects relating to the matrix phase. Our results show that linear elastic properties such as elastic modulus, flexural strength and fracture toughness are not good descriptors of the fatigue resistance of dental resin composite under cyclic bending, and may therefore have limited clinical relevance. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  3. Effect of Water Absorption on the Impact Properties of Carbon Fiber/ Epoxy Composites

    Institute of Scientific and Technical Information of China (English)

    LU Xiao-jun; ZHANG Qi

    2006-01-01

    In this paper, the effects of test temperatures and time on the impact damage behavior of unidirectional carbon fiber reinforced epoxy resin composites, immersed in pure water, on a pendulum impact tester, was studied. The results show that immersion in liquids has a significant effect on the impact resistance of the unidirectional composite material. It is obvious that after immersion, the mass of the material increases. The fracture initiation forces as well as the fracture initiation energy decrease as the immersion time lengthens. Moreover, the higher the temperature and the longer the time are, the more the crack propagation energy and the ductility index will be. Immersion makes the fracture mode change from the dominant fiber fracture into dominant delamination. All in all, immersion decreases the impact resistance of the composites and causes the fracture mode to change.

  4. Renewable and superior thermal-resistant cellulose-based composite nonwoven as lithium-ion battery separator.

    Science.gov (United States)

    Zhang, Jianjun; Liu, Zhihong; Kong, Qingshan; Zhang, Chuanjian; Pang, Shuping; Yue, Liping; Wang, Xuejiang; Yao, Jianhua; Cui, Guanglei

    2013-01-01

    A renewable and superior thermal-resistant cellulose-based composite nonwoven was explored as lithium-ion battery separator via an electrospinning technique followed by a dip-coating process. It was demonstrated that such nanofibrous composite nonwoven possessed good electrolyte wettability, excellent heat tolerance, and high ionic conductivity. The cells using the composite separator displayed better rate capability and enhanced capacity retention, when compared to those of commercialized polypropylene separator under the same conditions. These fascinating characteristics would endow this renewable composite nonwoven a promising separator for high-power lithium-ion battery.

  5. Incremental dynamic analysis of concrete moment resisting frames reinforced with shape memory composite bars

    Science.gov (United States)

    Zafar, Adeel; Andrawes, Bassem

    2012-02-01

    Fiber reinforced polymer (FRP) reinforcing bars have been used in concrete structures as an alternative to conventional steel reinforcement, in order to overcome corrosion problems. However, due to the linear behavior of the commonly used reinforcing fibers, they are not considered in structures which require ductility and damping characteristics. The use of superelastic shape memory alloy (SMA) fibers with their nonlinear elastic behavior as reinforcement in the composite could potentially provide a solution for this problem. Small diameter SMA wires are coupled with polymer matrix to produce SMA-FRP composite, which is sought in this research as reinforcing bars. SMA-FRP bars are sought in this study to enhance the seismic performance of reinforced concrete (RC) moment resisting frames (MRFs) in terms of reducing their residual inter-story drifts while still maintaining the elastic characteristics associated with conventional FRP. Three story one bay and six story two bay RC MRF prototype structures are designed with steel, SMA-FRP and glass-FRP reinforcement. The incremental dynamic analysis technique is used to investigate the behaviors of the two frames with the three different reinforcement types under a suite of ground motion records. It is found that the frames with SMA-FRP composite reinforcement exhibit higher performance levels including lower residual inter-story drifts, high energy dissipation and thus lower damage, which are important for structures in highly seismic zones.

  6. Effect of the fatty acid composition of acclimated oenological Lactobacillus plantarum on the resistance to ethanol.

    Science.gov (United States)

    Bravo-Ferrada, B M; Gómez-Zavaglia, A; Semorile, L; Tymczyszyn, E E

    2015-02-01

    The aim of this work was to evaluate the changes due to acclimation to ethanol on the fatty acid composition of three oenological Lactobacillus plantarum strains and their effect on the resistance to ethanol and malic acid consumption (MAC). Lactobacillus plantarum UNQLp 133, UNQLp 65.3 and UNQLp 155 were acclimated in the presence of 6 or 10% v/v ethanol, for 48 h at 28°C. Lipids were extracted to obtain fatty acid methyl esters and analysed by gas chromatography interfaced with mass spectroscopy. The influence of change in fatty acid composition on the viability and MAC in synthetic wine was analysed by determining the Pearson correlation coefficient. Acclimated strains showed a significant change in the fatty composition with regard to the nonacclimated strains. Adaptation to ethanol led to a decrease in the unsaturated/saturated ratio, mainly resulting from an increase in the contribution of short-length fatty acid C12:0 and a decrease of C18:1. The content of C12:0 was related to a higher viability after inoculation of synthetic wine. The MAC increased at higher contents in saturated fatty acid, but its efficiency was strain dependent.

  7. Effects of resistance training on binge eating, body composition and blood variables in type II diabetics

    Directory of Open Access Journals (Sweden)

    Moisés Simão Santa Rosa de Sousa

    2014-03-01

    This study examined the effects of 12 weeks of resistance training (RT on binge eating, body composition and blood variables and their correlations in 34 sedentary adults with type II diabetes. The participants aged 58.94 ± 10.66, had body weight of 71.62 ± 11.85 and BMI of 29.64 ± 4.27. Blood samples were collected for analysis of serum leptin, glucose, insulin, LDL, HDL, total cholesterol and triglyceride. The binge eating was assessed by the binge eating scale and the body composition by bioelectrical impedance. The training included three weekly sessions for 12 weeks, with three sets from 12 to 15 repetitions for the main muscle groups, and interval from 1 to 2 minutes between the sets. A significant decrease was found for the binge eating, body weight, BMI, fat percentage, and fat weight. As for the blood variables, there was a significant reduction in leptin; non-significant reductions in glucose, total cholesterol, LDL and triglycerides; as well a significant increase in HDL and non-significant increase in insulin. In conclusion the 12 weeks of RT proved to be enough to decrease the binge eating, to positively adjust the body composition and to modify the blood profile, demonstrating an association at a lower or higher level between these variables.

  8. Fracture Resistance of Endodontically Treated Teeth Restored with 2 Different Fiber-reinforced Composite and 2 Conventional Composite Resin Core Buildup Materials: An In Vitro Study.

    Science.gov (United States)

    Eapen, Ashly Mary; Amirtharaj, L Vijay; Sanjeev, Kavitha; Mahalaxmi, Sekar

    2017-09-01

    The purpose of this in vitro study was to comparatively evaluate the fracture resistance of endodontically treated teeth restored with 2 fiber-reinforced composite resins and 2 conventional composite resin core buildup materials. Sixty noncarious unrestored human maxillary premolars were collected, endodontically treated (except group 1, negative control), and randomly divided into 5 groups (n = 10). Group 2 was the positive control. The remaining 40 prepared teeth were restored with various direct core buildup materials as follows: group 3 teeth were restored with dual-cure composite resin, group 4 with posterior composite resin, group 5 with fiber-reinforced composite resin, and group 6 with short fiber-reinforced composite resin. Fracture strength testing was performed using a universal testing machine. The results were statistically analyzed by 1-way analysis of variance and the post hoc Tukey test. Fracture patterns for each sample were also examined under a light microscope to determine the level of fractures. The mean fracture resistance values (in newtons) were obtained as group 1 > group 6 > group 4 > group 3 > group 5 > group 2. Group 6 showed the highest mean fracture resistance value, which was significantly higher than the other experimental groups, and all the fractures occurred at the level of enamel. Within the limitations of this study, a short fiber-reinforced composite can be used as a direct core buildup material that can effectively resist heavy occlusal forces against fracture and may reinforce the remaining tooth structure in endodontically treated teeth. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  9. The ‘Sticky Elastica’: delamination blisters beyond small deformations

    KAUST Repository

    Wagner, Till J. W.

    2013-01-01

    We consider the form of an elastic loop adhered to a rigid substrate: the \\'Sticky Elastica\\'. In contrast to previous studies of the shape of delamination \\'blisters\\', the theory developed accounts for deflections with large slope (i.e. geometrically nonlinear). Starting from the classical Euler Elastica we provide numerical results for the dimensions of such blisters for a variety of end-end confinements and develop asymptotic expressions that reproduce these results well, even up to the point of self-contact. Interestingly, we find that the width of such blisters does not grow monotonically with increased confinement. Our theoretical predictions are confirmed by simple desktop experiments and suggest a new method for the measurement of the elastocapillary length for deformations that cannot be considered small. We discuss the implications of our results for applications such as flexible electronics. © 2013 The Royal Society of Chemistry.

  10. Ductile film delamination from compliant substrates using hard overlayers

    Energy Technology Data Exchange (ETDEWEB)

    Cordill, M.J. [Erich Schmid Institute of Materials Science, Austrian Academy of Sciences (Austria); Marx, V.M.; Kirchlechner, C. [Max-Plank-Insitut für Eisenforschung GmbH, Düsseldorf (Germany)

    2014-11-28

    Flexible electronic devices call for copper and gold metal films to adhere well to polymer substrates. Measuring the interfacial adhesion of these material systems is often challenging, requiring the formulation of different techniques and models. Presented here is a strategy to induce well defined areas of delamination to measure the adhesion of copper films on polyimide substrates. The technique utilizes a stressed overlayer and tensile straining to cause buckle formation. The described method allows one to examine the effects of thin adhesion layers used to improve the adhesion of flexible systems. - Highlights: • Measuring the adhesion energies of ductile metal–polymer interfaces is difficult. • A Cu film would plastically deform under tensile strain without a Cr overlayer. • A Cr overlayer forces cracking and induces buckling between the crack fragments. • The adhesion energy of the metal–polymer interface can be measured.

  11. Multifunctional smart composites with integrated carbon nanotube yarn and sheet

    Science.gov (United States)

    Chauhan, Devika; Hou, Guangfeng; Ng, Vianessa; Chaudhary, Sumeet; Paine, Michael; Moinuddin, Khwaja; Rabiee, Massoud; Cahay, Marc; Lalley, Nicholas; Shanov, Vesselin; Mast, David; Liu, Yijun; Yin, Zhangzhang; Song, Yi; Schulz, Mark

    2017-04-01

    Multifunctional smart composites (MSCs) are materials that combine the good electrical and thermal conductivity, high tensile and shear strength, good impact toughness, and high stiffness properties of metals; the light weight and corrosion resistance properties of composites; and the sensing or actuation properties of smart materials. The basic concept for MSCs was first conceived by Daniel Inman and others about 25 years ago. Current laminated carbon and glass fiber polymeric composite materials have high tensile strength and are light in weight, but they still lack good electrical and thermal conductivity, and they are sensitive to delamination. Carbon nanotube yarn and sheets are lightweight, electrically and thermally conductive materials that can be integrated into laminated composite materials to form MSCs. This paper describes the manufacturing of high quality carbon nanotube yarn and sheet used to form MSCs, and integrating the nanotube yarn and sheet into composites at low volume fractions. Various up and coming technical applications of MSCs are discussed including composite toughening for impact and delamination resistance; structural health monitoring; and structural power conduction. The global carbon nanotube overall market size is estimated to grow from 2 Billion in 2015 to 5 Billion by 2020 at a CAGR of 20%. Nanotube yarn and sheet products are predicted to be used in aircraft, wind machines, automobiles, electric machines, textiles, acoustic attenuators, light absorption, electrical wire, sporting equipment, tires, athletic apparel, thermoelectric devices, biomedical devices, lightweight transformers, and electromagnets. In the future, due to the high maximum current density of nanotube conductors, nanotube electromagnetic devices may also become competitive with traditional smart materials in terms of power density.

  12. Resistivity and Its Anisotropy Characterization of 3D-Printed Acrylonitrile Butadiene Styrene Copolymer (ABS/Carbon Black (CB Composites

    Directory of Open Access Journals (Sweden)

    Jie Zhang

    2017-01-01

    Full Text Available The rapid printing of 3D parts with desired electrical properties enables numerous applications. Fused deposition modeling (FDM using conductive thermoplastic composites has been a valuable approach for such fabrication. The parts produced by FDM possess various controllable structural features, but the effects of the structural features on the electrical properties remain to be determined. This study investigated the effects of these features on the electrical resistivity and resistivity anisotropy of 3D-printed ABS/CB composites. The effects of the process parameters of FDM, including the layer thickness, raster width, and air gap, on the resistivity in both the vertical and horizontal directions for cubic samples were studied because the internal structure of the printed parts depended on those process parameters. The resistivities of printed parts in different parameter combinations were measured by an impedance analyzer and finite element models were created to investigate the relationship between the resistivity and the internal structure. The results indicated that the parameters remarkably affected the resistivity due to the influence of voids and the bonding condition between adjacent fibers. The resistivity in the vertical direction ranged from 70.40 ± 2.88 Ω·m to 180.33 ± 8.21 Ω·m, and the resistivity in the horizontal direction ranged from 41.91 ± 2.29 Ω·m to 58.35 ± 0.61 Ω·m at the frequency of 1 kHz. Moreover, by adjusting the resistivities in different directions, the resistivity anisotropy of the printed parts can be manipulated from 1.01 to 3.59. This research may serve as a reference to fabricate parts with sophisticated geometry with desired electrical resistivity and resistivity anisotropy.

  13. Microstructure and Corrosion Resistance of Cr7C3/γ-Fe Ceramal Composite Coating Fabricated by Plasma Cladding

    Institute of Scientific and Technical Information of China (English)

    LIU Junbo

    2007-01-01

    A new type in situ Cr7C3/γ-Fe ceramal composite coating was fabricated on substrate of hardened and tempered grade C steel by plasma cladding with Fe-Cr-C alloy powders. The ceramal composite coating has a rapidly solidified microstructure consisting of primary Cr7C3 and the Cr7C3/γ-Fe eutectics, and is metallurgically bonded to the degree C steel substrate. The corrosion resistances of the coating in water solutions of 0.5 mol/L H2SO4 and 3.5% NaCl were evaluated utilizing the electrochemical polarization corrosion-test method. Because of the inherent excellent corrosion-resisting properties of the constituting phase and the rapidly solidified homogeneous microstructure, the plasma clad ceramal composite coating exhibits excellent corrosion resistance in the water solutions of 0.5 mol/L H2SO4 and 3.5% NaCl.

  14. XPS study of the corrosion resisting composite alloying layer obtained by double glow plasma with the brush plating Ni interlayer

    Institute of Scientific and Technical Information of China (English)

    Jiang Xu; Xishan Xie; Zhong Xu; Wenjin Liu

    2004-01-01

    The Ni-Cr-Mo-Cu multi-element surface alloying with the electric brush plating Ni interlayer on the low carbon steel substrate has been investigated. By the electrochemical method in 3.5% (mass fraction) NaC1 solution, the corrosion resistance of the composite alloying layer and single alloying layer is determined. The experimental results show that the corrosion resistance of the composite alloying layer is obviously better than that of the single alloying layer. The structure and composition of passive films formed on the two kinds of alloyed layers after electrochemical tests in 3.5% NaC1 solution have been studied using X-ray photoelectron spectroscopy (XPS). It is concluded that the double glow plasma surface alloying of low carbon steel with the electric brush plating Ni interlayer is an appropriate technique to enhance the corrosion resistance compared with the single double glow surface alloying.

  15. Hybrid diffusive/PVD treatments to improve the tribological resistance of Ti-6Al-4V.

    Science.gov (United States)

    Marin, E; Offoiach, R; Lanzutti, A; Regis, M; Fusi, S; Fedrizzi, L

    2014-01-01

    Titanium alloys are nowadays used for a wide range of biomedical applications thanks to their combination of high mechanical resistance, high corrosion resistance and biocompatibility. Nevertheless, the applicability of titanium alloys is sometimes limited due to their low microhardness and tribological resistance. Thus the titanium alloys cannot be successfully applied to prosthetic joint couplings. A wide range of surface treatments, in particular PVD coatings such as CrN and TiN, have been used in order to improve the tribological behaviour of titanium alloys. However, the low microhardness of the titanium substrate often results in coating failure due to cracks and delamination. For this reason, hybrid technologies based on diffusive treatments and subsequent PVD coatings may improve the overall coating resistance. In this work, conventional PVD coatings of CrN or TiCN, deposited on Titanium Grade 5, were characterized and then combined with a standard thermal diffusive nitriding treatment in order to improve the tribological resistance of the titanium alloys and avoid coating delamination. The different treatments were studied by means of scanning electron microscopy both on the sample surface and in cross-section. In-depth composition profiles were obtained using glow discharge optical emission spectrometry (GDOES) and localized energy dispersive X-ray diffraction on linear scan-lines. The microhardness and adhesion properties of the different treatments were evaluated using Vickers microhardness tests at different load conditions. The indentations were observed by means of SEM in order to evaluate delaminated areas and the crack's shape and density. The tribological behaviour of the different treatments was tested in dry conditions and in solution, in alternate pin-on-flat configuration, with a frequency of 0.5 Hz. After testing, the surface was investigated by means of stylus profilometry and SEM both on the surface and in cross-section. The standalone PVD

  16. Monitoring Delamination of Thermal Barrier Coatings by Near-Infrared and Upconversion Luminescence Imaging

    Science.gov (United States)

    Eldridge, J. I.; Martin, R. E.; Singh, Jogender; Wolfe, Doug E.

    2008-01-01

    Previous work has demonstrated that TBC delamination can be monitored by incorporating a thin luminescent sublayer that produces greatly increased luminescence intensity from delaminated regions of the TBC. Initial efforts utilized visible-wavelength luminescence from either europium or erbium doped sublayers. This approach exhibited good sensitivity to delamination of electron-beam physical-vapor-deposited (EB-PVD) TBCs, but limited sensitivity to delamination of the more highly scattering plasma-sprayed TBCs due to stronger optical scattering and to interference by luminescence from rare-earth impurities. These difficulties have now been overcome by new strategies employing near-infrared (NIR) and upconversion luminescence imaging. NIR luminescence at 1550 nm was produced in an erbium plus ytterbium co-doped yttria-stabilized zirconia (YSZ) luminescent sublayer using 980-nm excitation. Compared to visible-wavelength luminescence, these NIR emission and excitation wavelengths are much more weakly scattered by the TBC and therefore show much improved depth-probing capabilities. In addition, two-photon upconversion luminescence excitation at 980 nm wavelength produces luminescence emission at 562 nm with near-zero fluorescence background and exceptional contrast for delamination indication. The ability to detect TBC delamination produced by Rockwell indentation and by furnace cycling is demonstrated for both EB-PVD and plasma-sprayed TBCs. The relative strengths of the NIR and upconversion luminescence methods for monitoring TBC delamination are discussed.

  17. Failure in Three-Dimensional Woven Composites Subjected to Quasi-Static and Dynamic Indentation

    Science.gov (United States)

    2013-09-12

    composites, High strain rate testing, Impact behavior, Interlaminar shear strength, Short beam shear strength, Textile composites Bhavani V. Sankar...propagation in plain woven laminates and 3D orthogonal woven composites during short beam shear tests were analyzed using FEA. Two kinds of 3D woven...delamination damage caused by such impacts the characterization of delamination damage in laminated composites becomes critical to creating safe designs. 3D

  18. On the Fracture Toughness and Crack Growth Resistance of Bio-Inspired Thermal Spray Hybrid Composites

    Science.gov (United States)

    Resnick, Michael Murray

    the values of a real nacre. Although, the fracture toughness was primary property of this study and the values were well matched, the fracture behavior found to be somewhat different between the hybrid composite and nacre. In particular, the hybrid composite was unable to exhibit any significant toughness under slow crack growth conditions, which is the most attractive feature of nacre. This thesis focuses on first investigating the toughness in the sprayed hybrid composites by using standard resistance curve (R-curve) measurements. The study then focused on developing thermal spray modified hybrid composites with improved toughness, as well as with higher application temperatures, beyond the limitation of epoxy.

  19. Electrical behavior of laminated composites with intralaminar degradation: A comprehensive micro-meso homogenization procedure

    KAUST Repository

    Selvakumaran, Lakshmi

    2014-03-01

    Electrical Resistance Tomography (ERT) is a promising health monitoring technique to assess damage in laminated composites. Yet, the missing link between the various complex degradation mechanisms within the laminate and its global change in resistivity prevents ERT from being used as a quantitative technique. We propose an electrical mesomodel that can establish this link between the various microscale degradations and the resistivity changes in the measurements. The mesoscale homogenization of transverse cracks with local delamination of the ply is first described for in-plane electrical loading for both the outer and the inner plies. The mesoscale model is then extended to include the out-of-plane loading. The relationship between the mesoscale damage indicators and the degradation morphology is identified. These damage indicators are found to be intrinsic to the ply. As such, this defines the first step towards the interpretation of resistivity measurement in terms of micromechanical damage. © 2013 Elsevier Ltd.

  20. Effect of phase asynchronism on the fatigue resistance of laminated fiber composites in a plane stress state

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Ya.A.; Limonov, V.A.; Tamuzh, V.P.

    1992-03-01

    The introduction of composite materials in different regions of technology to create load-bearing structural elements working under fatigue loads is making it necessary to study the effect of different structural, service, and other factors on the fatigue resistance of these materials. For example, other authors experimentally studied structural features of laminated composites. Specifically, they studied the way in which fatigue resistance is affected by the angles of orientation and sequence of the layers of a unidirectional organic-fiber-reinforced plastic through the thickness of the laminated packet. Elsewhere, an experimental study was made of unidirectional and laminated composites to determine the effect on fatigue resistance of such service factors as combined simple cyclic loading, loading frequency, ambient temperature, humidity, and asymmetry of the loading cycle. Considering the variety of laminated fiber composites being developed in addition to those that already exist and taking into account the wide range of corresponding service characteristics, it become clear that the fatigue resistance of these materials cannot be evaluated by experimental methods alone. Even for one specific composite, such empirical evaluation requires significant amounts of time. Previous authors proposed and thoroughly tested a theoretical model of the endurance of composite laminates. This method can be used in conjunction with available test results to develop a reliable empirical-theoretical method of calculating the fatigue resistance of composites that will account for the main structural and service characteristics of the material. However, their results are for simple loading, while under actual conditions, with a multiaxial stress state, loading is nonproportional, i.e. it occurs over a complex path. The simplest of nonproportional loading is encountered with asynchronous load application.