Chemical changes in well fluids from the Los Humeros geothermal field: Evidences for deep recharge; Cambios quimicos en fluidos de pozos del campo geotermico de Los Humeros: Evidencia de recarga profunda

Energy Technology Data Exchange (ETDEWEB)

Barragan Reyes, Rosa Maria; Arellano Gomez, Victor Manuel [Instituto de Investigaciones Electricas, Gerencia de Geotermia, Cuernavaca, Morelos (Mexico)]. E-mail: rmb@iie.org.mx; Flores Armenta, Magaly [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico); Tovar Aguado, Rigoberto [Comision Federal de Electricidad (Mexico)

2008-07-15

Fluid (water and steam) chemical changes over time were studied in 20 wells in the Los Humeros, Mexico, geothermal field for the purpose of correlating such changes with physical processes occurring in the reservoir due to exploitation. Most wells (except well H-1) produce high-enthalpy fluids with almost no liquid, making gas geochemistry important in this field. Liquid-phase studies include fluid classification, determination of water-rock equilibrium state, and reservoir-temperature estimates. Changes in gas composition through time were studied using the Fischer-Tropsch (FT) reaction and the combined balance pyrite-hematite-magnetite (HSH2) as the buffer controlling H{sub 2}S fluid concentration. Data for most wells from 1987-1995 and 2000-2005 indicate the presence of deeper-fluid recharge, with maximum temperatures occurring in 1994-95 and 2005. The estimated temperature in well H-1 in 1994 was 305 degrees Celsius and the estimated temperature in well H-7 was 338 degrees Celsius in 1995. Temperature estimations from 2005 data were 222 degrees Celsius in well H-1D and 350 degrees Celsius in well H-7. These results are considered caused by the entrance of deeper fluids due to the increase of secondary permeability, which in turn is related to the seismicity increase in the zone. At the same time, re-injection returns in the steam phase were identified in well discharges during 1995-2000 by means of the FT-HSH2 diagram. [Spanish] Se realizo un estudio de los cambios quimicos ocurridos en fluidos (liquido y vapor) de veinte pozos del campo geotermico de Los Humeros, Pue., Mexico, con objeto de investigar la ocurrencia de procesos del yacimiento relacionados con la explotacion. La mayoria de los pozos (excepto el pozo H-1) se caracterizan por producir descargas de alta entalpia con escasa produccion de liquido, por lo que en este campo la geoquimica de gases juega un papel importante. El estudio de la fase liquida incluyo la clasificacion de los fluidos, la

Gaseous equilibrium in sector CP IV of the Cerro Prieto, B.C. Mexico geothermal field; Equilibrio gaseoso en el sector CP IV del campo geotermico Cerro Prieto, B.C., Mexico

Energy Technology Data Exchange (ETDEWEB)

Barragan Reyes, Rosa Maria; Arellano Gomez, Victor Manuel; Portugal Marin, Enrique [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); De Leon Vivar, Jesus [Comision Federal de Electricidad, Campo Geotermico Cerro Prieto, Cerro Prieto, B. C. (Mexico)

2007-07-01

Sector CP IV is located in the NE portion of the Cerrro Prieto geothermal field. The wells of this zone produce two-phase fluids, with different characteristics as far as their steam fraction content; in the central part and towards the NW the fluids are of dominant liquid type whereas towards the E and the S, the fluid contains a relatively higher steam fraction. The results of gaseous equilibrium FT- HSH3 showed that the fluids in the deposit are at temperatures between 275 Celsius degrees and 310 Celsius degrees and contain steam fractions between 0.01 and 0.5. The data found for the natural state are aligned in a tendency defined in the diagram FT- HSH3, that suggest the wells receive different proportions from preexisting steam in the deposit, which are mixed with the liquid phase to produce the observed discharges. The present data, besides showing the presence of deposit steam, also indicates the entrance of lower temperature fluid in the central part of sector CP IV. [Spanish] El sector CP IV se localiza en la porcion NE del campo geotermico Cerro Prieto. Los pozos de esta zona producen fluidos bifasicos, con diferentes caracteristicas en cuanto a su contenido de fraccion de vapor: en la parte central y hacia el NW los fluidos son de tipo liquido dominante mientras que hacia el E y hacia el S, el fluido contiene una fraccion relativamente alta de vapor. Los resultados de equilibrio gaseoso FT-HSH3 mostraron que los fluidos en el yacimiento se encuentran a temperaturas de entre 275 grados Celsius y 310 grados Celsius y contienen fracciones de vapor de entre -.01 y .5. Los datos hallados para el estado natural se alinean en una tendencia definida en el diagrama FT-HSH3, que sugiere que los pozos reciben diferentes proporciones de vapor pre-existente en el yacimiento, que se mezclan con fase liquida para producir las descargas que se observan. Los datos actuales, ademas de mostrar la presencia de vapor de yacimiento, tambien indican la entrada de fluidos de

Analysis of the automation and control of the well production conditions in the Cerro Prieto geothermal field, Mexico; Analisis de la automatizacion y del control de las condiciones de produccion de los pozos del campo geotermico de Cerro Prieto, BC, Mexico

Energy Technology Data Exchange (ETDEWEB)

Murillo Zamora, Isaac [Comision Federal de Electricidad, Mexicali, BC, (Mexico); Ocampo Diaz, Juan de Dios [Universidad Autonoma de Baja California, Mexicali, BC, (Mexico); De la Pena Reyna, Gilberto [Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

2005-12-01

Through 31 years of development of the Cerro Prieto geothermal field, the number of wells in operation and the distances between them has been increasing. Now there are 150 wells producing a mixture of water and steam at different ratios, depending on the reservoir characteristics (pressure, temperature, depth, etc.) and the operation conditions in the superficial installations (obstructions in the orifice plates diameter, separator pressures, etc.). Therefore, Comision Federal de Electricidad (CFE) has started a pilot plan to handle the automation and control of the operating conditions of production wells, and to install a data production acquisition system. The initial results of the system are in this paper. [Spanish] A traves de los 31 anos de desarrollo del campo geotermico de Cerro Prieto el numero de pozos en operacion asi como la distancia entre ellos se ha estado incrementando. Ahora hay mas de 150 pozos produciendo una cantidad de mezcla de agua y vapor a diferentes rangos, dependiendo de las caracteristicas del yacimiento (presion, temperatura, profundidad, etc.) y de las condiciones de operacion de las instalaciones superficiales (diametros de placas de orificio obstruidos, presion de los separadores, etc.). Como resultado la Comision Federal de Electricidad (CFE) ha dado inicio a un plan de pruebas para llevar a cabo la automatizacion y control de las condiciones de operacion de los pozos productores, e instalar un sistema con equipos para recoleccion de datos del campo, cuyos primeros resultados se presentan en este articulo.

Corrosion in pipelines and well casings at the Cerro Prieto geothermal field, BC; Corrosion en tuberias de linea y de revestimiento de pozos del campo geotermico de Cerro Prieto, BC

Energy Technology Data Exchange (ETDEWEB)

Miranda Herrera, Carlos A.; Canchola Felix, Ismael; Raygoza Flores, Joaquin; Mora Perez, Othon [Comision Federal de Electricidad, Residencia General de Cerro Prieto, Mexicali, Baja California (Mexico)]. E-mail: carlos.miranda02@cfe.gob.mx

2009-07-15

In the area called Poligono Hidalgo, inside the Cerro Prieto IV zone in the Cerro Prieto geothermal field, BC, corrosion has occurred in the last few years on well casings and pipelines used for geothermal fluids. Corrosion test results are presented here for pipes, type API L-80 and ASTM A-53 grade B, which were subjected to condensate from wells 403 and 424. These wells have thrown corroded material from their respective casings. With these data we pinpoint corrosive conditions in this field area and determine which pipes are adequate to case wells in similar chemical, production conditions to minimize adverse effects and extend the life of the well, allowing more efficient exploitation of the deepest production zones in the reservoir. [Spanish] En el campo geotermico de Cerro Prieto, BC, dentro del area del Poligono Hidalgo en el sector conocido como Cerro Prieto IV, algunos pozos han presentado en los ultimos anos desgastes en sus tuberias de revestimiento y en las tuberias de linea para el transporte del fluido geotermico. Se presentan resultados de pruebas de corrosion con tuberias tipo API L-80 y ASTM A-53 grado B al ser sometidas al condensado de los pozos 403 y 424, los cuales han estado arrojando material de sus respectivas tuberias de revestimiento. Con estos datos se pretende conocer las condiciones corrosivas de esa zona del campo y determinar cual seria la tuberia ideal a utilizar en pozos con condiciones quimicas de produccion semejantes a fin de minimizar este efecto adverso y prolongar la vida de los pozos, a la vez que se permita la explotacion eficiente de las zonas productoras mas profundas del yacimiento.

Evolution evidence of a basic fluid to an acid based in the analysis of hydrothermal alteration of the geothermic field of the Azufres, Michoacan; Evidencias de evolucion de un fluido basico a acido a partir del analisis de la alteracion hidrotermal del campo geotermico de los Azufres, Michoacan

Energy Technology Data Exchange (ETDEWEB)

Gonzalez Partida, Eduardo [Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)

2000-07-01

Hydrothermal alteration at the Los Azufres geothermal field is mostly composed of calc-silicate minerals that define a propylitic alteration zone, which shows progressive dehydration with depth and temperature increase. A generalized zoning of the calc-silicate zone can be observed, with zeolites in the upper part and epidote-clinozoisite at the deepest levels. An argillic alteration zone overlies the calc-silicate zone and is the dominant surface manifestation of the hydrothermal alteration. In some parts, there is a mineral assemblage composed of kaolinite-alunite-native sulfur-quartz (advanced argillic zone) formed by the interaction of vapor and shallow groundwater. The proto-fluid at the Los Azufres geothermal system is related to a neutral sodium chlorine brine, which favors deep propyllitic alteration (productive zone). This zone is characterized by secondary permeability due to fracturing. At depth the geothermal field is dominated by a pressurized liquid, yielding to vapor at more shallow zone. The gradual change from a liquid to a vapor phase occurs through boiling at depths between 1,200 and 1,500 m, and is accompanied by changes in the hydrothermal alteration mineralogy. The type of alteration passes from proylitic to argillic by means of an oxidation-acidification process, which includes the participation of a gas, particularly CO{sub 2}. Considering the physicochemical characteristic of the brine and the evolution of the paragenetic sequence, the Los Azufres geothermal field could de considered a model for hydrothermal behavior at ore deposits which develop by boiling and oxidation of low sulfidation fossil hydrothermal fluids. [Spanish] En el campo geotermico de Los Azufres la zona de alteracion hidrotermal esta formada en su mayor parte por calcosilicatos (que definen una zona paragenetica del tipo propilitico), los cuales muestran una deshidratacion progresiva conforme se va profundizando e incrementandose la temperatura. Se puede generalizar un

Analysis of inflow in geothermal wells to determine their maximum flow; Analisis del influjo en pozos geotermicos para la determinacion de sus flujos maximos

Energy Technology Data Exchange (ETDEWEB)

Aragon-Aguilar, Alfonso; Izquierdo-Montalvo, Georgina; Pal-Verma, Mahendra; Santoyo-Gutierrez, Socrates [Instituto de Investigaciones Electricas (Mexico); Moya-Acosta, Sara L [Centro Nacional de Investigacion y Desarrollo Tecnologico (Mexico)

2009-01-15

Inflow performance relationships developed for petroleum and geothermal reservoirs are presented. Four of them were selected to be used in this work. Such relationships were developed considering features of a typical geothermal system. The performance of the selected relationships was assessed using data from production tests in several wells of different fields. A methodology is presented to determine the value of the maximum flow (W{sub max}) from the inflow relationships; its application is demonstrated using the data of the 10 production tests. It was found that the calculated value of W{sub max} under stabilization conditions may be related to the reservoir response. In general, there is a good agreement between the calculated values of W{sub max} from the different methods. The differences in the W{sub max} values vary within 10%. It was found that the stability in the calculated values of W{sub max} as a response of the reservoir is a function of the flow magnitude. So, the wells with flow greater than 200 t/h reach the stability of W{sub max} at openings 50% less of their total capacity. [Spanish] Se presentan las relaciones del comportamiento de influjo desarrolladas para yacimientos petroleros y geotermicos. Se seleccionaron cuatro de ellas para usar en este trabajo. Tales relaciones fueron desarrolladas considerando condiciones de un sistema geotermico tipico. Se analizo el comportamiento de las relaciones escogidas utilizando datos de pruebas de produccion de varios pozos de diferentes campos. Se presenta una metodologia para determinar el valor del flujo maximo (W{sub max}) a partir de las relaciones de influjo; se demuestra su aplicabilidad usando los datos de diez pruebas de produccion. Se encontro que el valor de W{sub max} calculado bajo condiciones de estabilizacion se puede relacionar con la respuesta del yacimiento. En general se encuentra buena concordancia entre los valores calculados de W{sub max} usando los diferentes metodos. Las

Economic, environmental and social impacts of geothermal development, and energy savings and efficient use of power in Baja California, Mexico; Impactos economicos, ambientales y sociales del desarrollo geotermico y del ahorro y uso eficiente de la electricidad en Baja California, Mexico

Energy Technology Data Exchange (ETDEWEB)

Campbell R, Hector E.; Montero A, Gisela [Universidad Autonoma de Baja California, Instituto de Ingenieria, Mexicali, Baja California (Mexico)]. E-mail: hecr@iing.mxl.uabc.mx; Lambert A., Alejandro A. [Universidad Autonoma de Baja California, Facultad de Ingenieria, Mexicali, Baja California (Mexico)

2011-01-15

geotermico a combustoleo hacia 1 a 1 de geotermia a gas natural. El costo unitario de energia del gas natural con una eficiencia de 50% es 24 veces el costo de la misma unidad de vapor geotermico con 16% de eficiencia. Generar con combustoleo o gas natural en turbinas simples cuesta el doble que con gas natural en ciclo combinado, mientras que con vapor geotermico cuesta tres veces menos. Al disminuir la participacion geotermica los costos de produccion de electricidad se incrementaron para llegar en 2005 a 122.80 USD/MWh. La salida del combustoleo disminuyo las emisiones de SO{sub x} de 4.16 kg/MWh a 0.19 kg/MWh. Los ciclos combinados con gas natural abatieron las emisiones relativas de NO{sub x} y CO{sub 2} en 30%, pero las 2.6 millones de toneladas anuales de CO{sub x} no variaron significativamente. La geotermia evita que se quemen anualmente 20 millones de barriles equivalentes de petroleo. La Prospectiva 2005-2025 implica para Baja California instalar 4500 MW adicionales para alcanzar 7200 MW. La matriz energetica se transformara dependiendo mas del gas natural que incrementara su participacion del 60% al 86%. La geotermia disminuira su participacion en la capacidad instalada al 10%, eliminando su efecto amortiguador en el costo de produccion. Las emisiones de SO{sub x} se mantendran en 2,200 toneladas por ano (t/a) emitiendose principalmente por la geotermoelectricidad, las de NO{sub x} aumentaran de 6,000 t/a en 2005 a 24,000 t/a en 2025, y las de CO{sub x} se incrementaran de 3.4 millones de t/a en 2005 a 12.7 millones de t/a en 2025. El costo de generacion sera afectado por los cambios en la matriz energetica al predominar el uso del gas natural. En terminos absolutos aumentara de 648 millones de dolares en 2005 a 2273 millones de dolares en 2025. El costo de generacion dependera en 70% del uso de gas natural. En la Planeacion Sistemica las metas planteadas se orientaron a: a) reducir los usos propios en los procesos de generacion, b) reducir los usos propios y las

Determination of the geothermal well damage from its production tests; Determinacion del dano en pozos geotermicos a partir de sus pruebas de produccion

Energy Technology Data Exchange (ETDEWEB)

Aragon Aguilar, Alfonso; Izquierdo Montalvo, Georgina; Arellano Gomez, Victor [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2011-06-13

. Sin embargo, la ejecucion de este tipo de pruebas requiere de periodos relativamente largos de tiempo para lograr la estabilizacion del pozo y de costos significativos. Por lo anterior se empezaron a desarrollar tecnicas para determinar el dano a partir de pruebas de produccion. En este articulo se presenta la curva-tipo de influjo geotermico afectada por dano, a partir de la cual se puede determinar el valor de este en un pozo geotermico para el tiempo en que se realiza su prueba de produccion. Se propone la metodologia para determinar el efecto de dano en el pozo usando la curva-tipo propuesta y se demuestra su aplicabilidad con ejemplos de mediciones de pruebas de descarga en pozos de campos geotermicos mexicanos. De los analisis efectuados se encuentra que el valor numerico del dano determinado en los pozos seleccionados aumenta en funcion del tiempo de explotacion, lo cual indica un deterioro en sus caracteristicas productivas. Lo anterior ayuda a conformar un respaldo tecnico para la toma de decisiones, sobre las acciones pertinentes que pueden ejecutar en el pozo.

Simulation of the flow phenomena in geothermal wells: developments and applications; Simulacion de los fenomenos de flujo en pozos geotermicos: desarrollos y aplicaciones

Energy Technology Data Exchange (ETDEWEB)

Garcia Gutierrez, Alfonso [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1994-07-01

In this paper the numerical simulators and the specialized computer programs that have been developed in the Departamento de Geotermia of the Instituto de Investigaciones Electricas (IIE) for the study of mass transport phenomena, momentum and heat in geothermal wells, are delineated. The developments can be assembled in 5 types: a) Fluid circulation during geothermal well construction; b) Production; c) Construction; d) Return to the thermal equilibrium; e) Thermodynamic and fluid transport properties, cements, and rocks. The applications realized include, besides the normal flow phenomena that occur in geothermal wells, the study of special problems that have been found in several wells of the geothermal fields in the country. These developments constitute a tool of great utility for the reservoir engineer`s daily work and for the understanding of the specific phenomena of infrequent occurrence. [Espanol] En este trabajo se describen los simuladores numericos y programas de computo especializados que se han desarrollado en el Departamento de Geotermia del Instituto de Investigaciones Electricas (IIE), para estudiar los fenomenos de transporte de masa, momentum y calor en pozos geotermicos. Los desarrollos pueden agruparse en 5 tipos: a) circulacion de fluidos durante la construccion de pozos, b) produccion, c) inyeccion, d) retorno a equilibrio termico, e) propiedades termodinamicas y de transporte de los fluidos, cementos y rocas. Las aplicaciones realizadas incluyen, ademas de los fenomenos normales de flujo que ocurren en pozos geotermicos, el estudio de problemas especiales que se han encontrado en diversos pozos de los campos geotermicos del pais. Estos desarrollos constituyen una herramienta de gran utilidad para el trabajo diario del ingeniero de yacimientos y para el entendimiento de fenomenos especificos de ocurrencia poco frecuente.

Geothermal infrastructure for an historic village in Tuscany: a sustainable retrofit solution

Directory of Open Access Journals (Sweden)

Valentina Marino

2016-06-01

Full Text Available Il comune di Montieri ha recentemente costruito una rete di teleriscaldamento alimentata a vapore geotermico. L’aspetto innovativo risiede nell’uso del vapore geotermico di scarto dalla produzione di elettricità, per fornire riscaldamento e acqua calda sanitaria per 425 utenze del centro storico. Con il progetto Geothermal Community (Concerto, FP7 sono stati intrapresi ulteriori obiettivi per l’ambiente costruito: la riduzione del consumo energetico degli edifici e l’aumento della quota delle risorse energetiche rinnovabili utilizzate dalla comunità. L’articolo propone una analisi dei benefici ambientali ed economici delle misure di efficienza energetica pianificate dal progetto Europeo alla luce dell’installazione della rete di teleriscaldamento. I risultati presentano uno spunto di riflessione interessante per la formulazione dei piani di riduzione delle emissioni delle aree urbane storiche Italiane ed Europee dove sono presenti simili infrastrutture. 

Isotopic Evolution of Wells in the Geothermal Field of Los Azufres, Michoacan, Mexico; Evolucion isotopica de fluidos de pozos del campo geotermico de Los Azufres, Michoacan, Mexico

Energy Technology Data Exchange (ETDEWEB)

Barragan Reyes, Rosa Maria; Portugal Marin, Enrique; Arellano Gomez, Victor Manel; Aragon Aguilar, Alfonso [Instituto de Investigaciones Electricas (Mexico); Sandoval Medina, Fernando [Comision Federal de Electricidad (Mexico)

2002-12-01

Isotopic ({delta}{sup 1}8 O and {delta}D) data from production and reinjection web fluids from the Los Azufres geothermal field were interpreted in order to define reservoir evolution and the occurrence of physical processes as a result of exploitation. The study included data of 30 wells, which were sampled in September, 2000. General results indicate that different phenomena seem to occur in both zones of the field. In the southern zone there are two different trends of behavior: a mixture of fluids evidenced by the {delta}D versus {delta}{sup 1}8 O trend with a positive slope, was interpreted as the result of reservoir vapor separation at a temperature above 220 Celsius degrees, since for temperatures above 220 Celsius degrees deuterium behaves as a volatile component. No well-defined {delta}{sup D} vs {delta}{sup 1}8 O trend was found for the northern zone, but some points seem to fit the same negative slope trend found in the souther zone. The study of reservoir temperatures estimated by different approaches for particular wells through time, as well as temperature results obtained with a heat and flow well simulator, suggest that reservoir boiling occurs in localized areas in both zone of the field. This process is probably due to exploitation. [Spanish] Se interpretaron datos isotopicos ({delta}{sup 1}8 O y {delta}D) de fluidos de pozos productores y de reinyeccion del campo geotermico de Los Azufres, Michoacan, Mexico, para definir la evolucion del yacimiento y la ocurrencia de procesos fisicos como resultado de la explotacion. En el estudio se consideran datos de treinta pozos segun el muestreo realizado en septiembre de 2000. El estudio de la evolucion en el tiempo de las estimaciones de temperatura de yacimiento mediante diferentes tecnicas, asi como la temperatura obtenida de simulacion de pozos, sugiere que ocurre ebullicion en areas localizadas en ambas zonas del campo debido a la explotacion. Los resultados generales indican la existencia de

Evolution of the CP-I sector of the Cerro Prieto geothermal reservoir, BC, and exploitation alternatives; Evolucion del sector CP-I del yacimiento geotermico de Cerro Prieto, BC, y alternativas de explotacion

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Rodriguez, Marco Helio [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Residencia General de Cerro Prieto, Mexicali, Baja California (Mexico)]. E-mail: marco.rodriguez01@cfe.gob.mx

2010-01-15

After 35 years of exploitation of the CP-I (Cerro Prieto I) sector of the Cerro Prieto geothermal field, its thermal conditions have been declined substantially; the number of production wells is reduced and exploitation has been abandoned in some zones. However with a binary cycle, it is still possible to generate electricity from the remaining reservoir energy. To do so, one needs to know a detailed reservoir history of the sector, identifying the best potential strata to be assessed. In this paper, the CP-I reservoir evolution is presented and its exploitation and main reservoir characteristics -which play important roles- are identified. The CP-I zones offering the best conditions for binary cycle exploitation are identified. Exploiting partially abandoned reservoir sections is crucial for the future of the field. If such sections can be made to produce, this will help reduce the progressive steam-production decline in the occurring since production began. The production decline had been mitigated by a large area available for drilling replacement production wells, but such an area is limited now, due to the vast number of operating wells. [Spanish] Despues de 35 anos de explotacion del yacimiento en el sector de CP-I (Cerro Prieto I) del campo geotermico de Cerro Prieto, BC, sus condiciones termicas han declinado considerablemente, por lo que el numero de pozos productores ha disminuido, dejando algunas zonas abandonadas a la explotacion. Sin embargo, aun es posible aprovechar la energia que contiene este sector del yacimiento para la generacion de electricidad mediante ciclo binario. Para ello primeramente se debe conocer en detalle cual ha sido la evolucion del yacimiento en este sector, identificando los estratos de mejor potencial para evaluarlos posteriormente. En este estudio se presenta la evolucion del yacimiento de CP-I como respuesta a su explotacion, identificando las principales caracteristicas del yacimiento que determinan su comportamiento. Asi

Heat losses estimation associated with the physical state of the thermal insulation of pipes vaporductos network in Cerro Prieto geothermal field; Estimacion de perdidas de calor asociadas al estado fisico del aislamiento termico de las tuberias de la red de vaporductos del campo geotermico Cerro Prieto

Energy Technology Data Exchange (ETDEWEB)

Ovando Castelar, Rosember; Martinez Estrella, Juan Ignacio; Garcia Gutierrez, Alfonso [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: rovando@iie.org.mx; jime@iie.org.mx; aggarcia@iie.org.mx; Canchola Felix, Ismael; Miranda Herrera, Carlos; Jacobo Galvan, Paul [Campo Geotermico de Cerro Prieto, Comision Federal de Electricidad, Mexicali, B.C. (Mexico)

2010-11-15

The Cerro Prieto Geothermal Field (CPGF) steam transportation network is constituted by 140 km of pipes with diameters ranging from 8 to 48 inches, which transport the steam of 165 producing wells to 13 power plants which have a total installed capacity of 720 MWe. Originally, the pipes are thermally insulated with a mineral wool or fiber glass layer and an external aluminum or iron cover. Due to the insulation material has been exposed to weather conditions during the field operation it shows nowadays different grades of wear-out, or even it is lacking in some parts of the network, causing higher heat losses from the pipes to the environment. In this work, the magnitude of the heat losses related with the present condition of the thermal insulation throughout the pipeline network is assessed. This involved determining the longitude and diameter, as well as the insulation condition of each single pipeline section, and the calculation of the heat transfer coefficients for the different thermal insulation conditions defined for this study. [Spanish] La red de transporte de vapor del campo geotermico Cerro Prieto (CGCP) esta constituida por aproximadamente 140 km de tuberias de 8 a 48 pulgadas de diametro, las cuales conducen el vapor producido por 165 pozos hacia 13 plantas generadoras, cuya capacidad instalada es de 720 MWe. Originalmente, estas tuberias son aisladas termicamente con una capa de 2 pulgadas de material aislante a base de lana mineral o fibra de vidrio, y una proteccion exterior de aluminio o hierro. Debido principalmente al impacto de las condiciones meteorologicas durante el tiempo de operacion del campo, en algunas porciones de la red el aislante presenta actualmente distintos grados de deterioro, o incluso se encuentra ausente, lo cual se traduce en una mayor perdida de calor desde las tuberias hacia el medio ambiente. En el presente trabajo se evalua la magnitud de las perdidas de calor asociadas al estado fisico del aislamiento termico de las

Geohydrologic conditions of the shallow aquifer in the Cerro Prieto geothermal field zone; Condiciones geohidrologicas del acuifero somero en la zona del campo geotermico de Cerro Prieto

Energy Technology Data Exchange (ETDEWEB)

Vazquez Gonzalez, Rogelio [CICESE, Ensenada, Baja California (Mexico)

1999-04-01

Based on geohydrologic information reported by Comision Nacional del Agua, Comision Federal de Electricidad and several academic institutions, we have performed an analysis to establish in general terms, the past and present behavior of the shallow aquifer in the Cerro Prieto geothermal zone (CPGZ). The main features of the aquifer, derived from the interpretation of the results obtained with several disciplines, are as follows: The shallow aquifer in CPGZ is part of the regional hydrologic system of the Mexicali valley basin. The basin is filled with unconsolidated delta deposits interbedded with alluvial sediments from the Sierra Cucapa, which forms an impervious boundary. Because the lack of information about the hydraulic properties of the sediments, just possible ranges of values were obtained for the hydraulic conductivity and storativity corresponding to three deposit environments: a) delta flood plain facies, b) estuarine or lagoon environment facies, c) distal alluvial fan facies. [Spanish] Con base en la informacion geohidrologica de la Comision Nacional del Agua, la Comision Federal de Electricidad e instituciones academicas, se realizo un analisis para establecer las condiciones geohidrologicas y el panorama general del comportamiento historico y actual del acuifero somero en la zona del campo geotermico de Cerro Prieto (CGCP). De la interpretacion e integracion de los resultados obtenidos de las diferentes disciplinas utilizadas en el desarrollo del estudio, se derivan las siguientes conclusiones: El acuifero somero en la zona del CGCP forma parte del acuifero regional del valle de Mexicali. La secuencia litologica en el area de estudio esta constituida por sedimentos no consolidados de origen deltaico interdigitados con sedimentos aluviales provenientes de la Sierra Cucapa, que sirve como frontera impermeable. La informacion sobre las propiedades hidraulicas de los materiales en el area de interes es limitada, por lo cual solo se determinan los

Lichens as biological monitors in the Los Azufres geothermal field, Michoacan, Mexico; Liquenes como indicadores biologicos en el campo geotermico Los Azufres, Michoacan, Mexico

Energy Technology Data Exchange (ETDEWEB)

Gomez Peralta, Marlene; Chavez Carmona, Arturo [Universidad Michoacana de San Nicolas de Hidalgo, Morelia (Mexico)

1995-09-01

The results obtained in the monitoring of the atmospheric emissions of the Los Azufres geothermal field in Michoacan State, Mexico utilizing lichens as monitors of the presence of sulphur and arsenic, at the areas near geothermal sites, both under evaluation and production, are presented. The results are based on symptoms which included: chlorosis, necrosis, brown and reddish spots, loss of adherence to substrate, thalli disintegration and disappearance of sensitive species; and also on the amounts of sulphur and arsenic contained in the lichens thallus. [Espanol] Se presentan los resultados obtenidos en el monitoreo de las emisiones atmosfericas del campo geotermico Los Azufres, Michoacan, Mexico en el que se utilizaron liquenes como indicadores de la presencia de azufre y arsenico, en las areas cercanas a los sitios de pozos geotermicos tanto en evaluacion como en produccion. Los resultados estan basados en sintomas que incluyen clorosis, necrosis, manchas cafes y rojizas, perdida de adherencia al sustrato, desintegracion del talo y desaparicion de especies sensibles; asi como en los contenidos de azufre y arsenico en los talos liquenicos.

Update of the conceptual geological model for the geothermal reservoir in Cerro Prieto, BC; Actualizacion del modelo geologico conceptual del yacimiento geotermico de Cerro Prieto, BC

Energy Technology Data Exchange (ETDEWEB)

Lira Herrera, Hector [Comision Federal de Electricidad, Mexicali, B.C., (Mexico)

2005-06-01

An updated, conceptual geologic model is presented for the geothermal reservoir in Cerro Prieto geothermal field. The tectonic extension that formed the Basin and Range Province of the Western United States and Northwestern Mexico during Upper Tertiary in the Cerro Prieto area resulted in the formation of a half graben tectonic basin between the Cerro Prieto and Imperial faults. Called the Cerro Prieto basin, it includes listric faults, predominately northwest-southwest trending, stepped generally to the northeast. The zone of cortical weakness, formed during the Tertiary, allowed an intrusion of basic rock associated with the magnetic anomaly know as Nuevo Leon. The intrusive rock has been fed by new magmatic intrusions originated by the present tectonic extension of the Gulf of California. The oldest rocks identified in the area are gneiss and biotite-schists of Permian-Jurassic age and tonalities of Jurassic-Cretaceous age in contact with Cretaceous granites, all representing the regional basement. The lithologic column in the subsurface of the Cerro Prieto basin in formed by a basement of Cretaceous granites; an argillaceous package resting on the basement composed of gray shales with interleaves of sandstone, Tertiary brown-shales and mudstone, with an average thickness of 2700 m; clastic sediments of the Quaternary age deposited mainly by the Colorado River and alluvial fans of the Cucapa Range, comprised of gravel, sands and clays with an average thickness of 2500 m, covering the shales. The fluids feeding the geothermal reservoir heat as they pass though the zone where the basic intrusive is located (the heat source) and migrate through the listric faults toward the permeable layers of sandstone located within the gray shales. [Spanish] Se presenta el modelo geologico conceptual actualizado del yacimiento geotermico de Cerro Prieto. La tectonica extensional que origino la Provincia de Cuencas y Cordilleras (Basin and Range) del oeste de Estados Unidos y

Hydrothermal alteration zones and present reservoir conditions: an approach to define production zones at the eastern portion of the Cerro Prieto geothermal field, BC; Zonas de alteracion hidrotermal y condiciones actuales del yacimiento: un enfoque para determinar zonas productoras al oriente del campo geotermico de Cerro Prieto, BC

Energy Technology Data Exchange (ETDEWEB)

Camacho Hernandez, Juan Manuel [Comision Federal de Electricidad, Residencia General de Cerro Prieto, Mexicali, Baja California (Mexico)]. E-mail: juan.camacho02@cfe.gob.mx

2009-07-15

Geological factors are as essential for locating new wells as they are for defining the production zones of these wells. At the Cerro Prieto geothermal field (CGCP), one of the most important geological factors is identification of the hydrothermal alteration zones (ZAH). These are divided into silica and epidote mineralogical zones (ZMSE), without CaCO{sub 3}, and silica and epidote mineralogical transition zones (ZTMSE), with CaCO{sub 3}. It has been observed that the continuous variation of reservoir thermodynamic conditions (temperature, pressure and enthalpy) is due mainly to the exploitation of geothermal resources. The presence of new thermodynamic conditions recorded at the reservoir has led to the re-location of production wells originally located during the drilling campaign of 2004 to 2006. At the geological sections on the eastern part of the CGCP, adjustments made to the well completions lie on the limits between the ZMSE and ZTMSE zones. In turn, this is related to the current, superior, thermodynamic reservoir conditions. Based on this, a new geologic approach is proposed to define possible production zones for new wells, relating the ZAH zones to current thermodynamic reservoir conditions. [Spanish] Los factores geologicos son determinantes, tanto para establecer nuevos sitios de perforacion como para determinar el intervalo productor de un pozo nuevo. En el campo geotermico de Cerro Prieto (CGCP) una de los factores mas importantes es la determinacion de las zonas de alteracion hidrotermal (ZAH) que se dividen en dos: zona mineralogica de silice y epidota (ZMSE), sin presencia de CaCO{sub 3}, y zona de transicion mineralogica de silice y epidota (ZTMSE), con presencia de CaCO{sub 3}. Por otra parte, tambien se ha constatado que la continua variacion de las condiciones termodinamicas del yacimiento (temperatura, presion y entalpia) es originada en buena medida por la explotacion del recurso geotermico. La ocurrencia de nuevas condiciones

Validation of Hiriart equation to compute steam production by the lip pressure method; Validacion de la ecuacion de Hiriart para calculo de gasto de vapor por el metodo de presion de labio

Energy Technology Data Exchange (ETDEWEB)

Flores Armenta, Magaly [Gerencia de Proyectos Geotermoelectricos de la Comision Federal de Electricidad, Morelia (Mexico)

1996-09-01

Mainly in new geothermal wells, it is necessary to evaluate the production in a very fast, simple and not expensive way, to know the convenience to install surface equipment, such as silencers and separators, to drive the steam to the commercial gathering system. In practice, one of the most known methods is the lip pressure one, which requires a simple set of installations. The objective of this paper is to validate the steam flow rate calculated by the lip pressure method, with respect to the ASME method. The ASME method is known for its accuracy, and is done by measuring the steam and liquid after a high pressure separator, by an orifice plate of known diameter and a triangular weir. Results of the validation show up the feasibility of application of the lip pressure method by using a simple adjustment equation. Percentage of mistake results less than 1%, without any notable influence of the production enthalpy. That equation to be applied in a general case, is as follows: Q{nu} =(20642)(F*P*D{sup 2}/{radical}h-2000). For the particular case of the Los Azufres geothermal field, the equation is: Q{nu}= 810*P*D{sup 2} [Espanol] En los pozos geotermicos, principalmente en los nuevos, es necesario evaluar su produccion de manera rapida, sencilla y economica, para determinar la conveniencia de instalar equipo superficial, como separadores, silenciadores, etc., que permita la integracion del vapor al sistema comercial de generacion electrica. Para fines practicos uno de los metodos mas conocidos es el de presion de labio, que solo requiere un arreglo sencillo de instalaciones superficiales. En este documento se validan y ajustan los calculos de produccion de vapor por ese metodo de presion de labio, con respecto a las mediciones exactas efectuadas con el metodo ASME. Este ultimo es reconocido internacionalmente por su precision, y se lleva a cabo separando la mezcla obtenida en superficie en un recipiente a presion para medir el vapor a traves de una placa de orificio

Determination of heat losses in the Cerro Prieto, Baja California, geothermal field steam transportation network based on the thermal insulation condition of the steam pipelines; Determinacion de perdidas de calor en la red de transporte de vapor del campo geotermico de Cerro Prieto, Baja California, con base en el estado fisico del aislamiento termico de vaporductos

Energy Technology Data Exchange (ETDEWEB)

Ovando Castelar, Rosember; Garcia Gutierrez, Alfonso; Martinez Estrella, Juan Ignacio [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: rovando@iie.org.mx; Canchola Felix, Ismael; Jacobo Galvan, Paul; Miranda Herrera, Carlos; Mora Perez, Othon [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Residencia General de Cerro Prieto, Mexicali, B.C. (Mexico)

2011-07-15

In Cerro Prieto Geothermal Field (CPGF), the steam from producing wells is transported to power plants through a large and complex system of pipes thermally insulated with a 2 inches thick mineral wool or a fiber glass layer and an external aluminum or iron cover. The insulation material has been exposed to weather conditions during the field operation and has suffered density and thickness changes. In some cases the insulation has been lost completely, increasing heat transfer from the pipes to the environment. This paper analyzes the impact of the conditions of thermal insulation on heat losses in the CPGF steam-pipeline network. The heat losses are calculated by applying an iterative method to determine the surface temperature based on a heat balance calculated from the three basic mechanisms of heat transfer: conduction, convection, and radiation. Finally, using length and diameter data corresponding to the condition of the thermal insulation of each pipeline-and field operation data, the overall heat losses are quantified for steam lines throughout the pipeline network in the field. The results allow us to evaluate the magnitude of the heat losses in comparison with the overall energy losses occurring during steam transport from wells to the power plants. [Spanish] En el Campo Geotermico de Cerro Prieto (CGCP), BC, el transporte de vapor desde los pozos hasta las plantas generadoras de electricidad se lleva a cabo mediante un extenso y complejo sistema de tuberias que tipicamente se encuentran aisladas termicamente con una capa de 2 pulgadas de material aislante a base de lana mineral o fibra de vidrio, y una proteccion mecanica de aluminio o hierro galvanizado. Debido a la exposicion a las condiciones meteorologicas a traves del tiempo de operacion del campo, el aislamiento ha experimentado cambios en su densidad y espesor y en ocasiones se ha perdido por completo, lo cual repercute en una mayor transferencia de calor de las tuberias hacia el medio ambiente

Seismologic study of Los Hum eros geothermal field, Pueblo, Mexico. Part I: Seismicity, source mechanisms and stress distribution; Estudio sismologico del campo geotermico de Los Humeros, Puebla, Mexico. Parte I: Sismicidad, mecanismos de fuente y distribucion de esfuerzos

Energy Technology Data Exchange (ETDEWEB)

Lermo, Javier; Antayhua, Yanet [Instituto de Ingenieria, Universidad Nacional Autonoma de Mexico, Mexico D.F (Mexico)]. E-Mail: jles@pumas.iingen.unam.mx; Quintanar, Luis [Instituto de Geofisica, Universidad Nacional Autonoma de Mexico, Mexico D.F (Mexico); Lorenzo, Cecilia [Gerencia de Proyectos Geotermoelectricos, Comision Federal de Electricidad, Michoacan (Mexico)

2008-01-15

The distribution of earthquakes at the surface and at depth in the Los Humeros geothermal field, Puebla (Mexico), is analyzed from 1997-2004. Data for 95 earthquakes were registered at more than five permanent and temporary stations installed by the Comision Federal de Electricidad and the Instituto de Ingenieria of the Universidad Nacional Autonoma de Mexico. The duration magnitudes of the quakes are equal to or lower than 3.6 Md and the focal depths do not exceed 4.0 km. Simple focal mechanisms and moment tensor inversions were made, and the number of earthquakes registered by two stations of the permanent network (numbers S05, S06) was compared with water-injection and steam-production volumes over a certain period. The results at the surface and at depth show seismic activity occurring in the northern zone of the field around injection wells I29 (well H-29) and I38 (well H-38); whereas, the simple focal mechanisms and moment tensors demonstrate stresses of heterogeneous origin, suggesting that part of the seismic activity in Los Humeros is probably induced, mainly by injecting water. [Spanish] Se analiza la distribucion en superficie y en profundidad de los sismos ocurridos en el campo geotermico de Los Humeros, Puebla (Mexico), durante el periodo 1997-2004. Los datos corresponden a 95 sismos registrados por mas de cinco estaciones permanentes y temporales instaladas por la Comision Federal de Electricidad y el Instituto de Ingenieria de la Universidad Nacional Autonoma de Mexico, cuyas magnitudes de duracion son menores o iguales a 3.6 Md y profundidades focales que no sobrepasan los 4.0 km. Asimismo, se realizaron mecanismos focales simples y de inversion de tensor de momento, y se comparo el numero de sismos registrados por dos estaciones de la red permanente (numeros S05, S06) con la inyeccion de agua y la produccion de vapor durante cierto tiempo. Los resultados en superficie y en profundidad muestran actividad sismica en la zona norte del campo, alrededor

Summary of the 2010 assessment on medium- to low-temperature geothermal resources in Mexico; Resumen de la evaluacion 2010 de los recursos geotermicos mexicanos de temperatura intermedia a baja

Energy Technology Data Exchange (ETDEWEB)

Iglesias, Eduardo R.; Torres, Rodolfo J.; Martinez Estrella, J. Ignacio; Reyes Picasso, Neftali [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: iglesias@iie.org.mx

2011-07-15

geothermal systems lies between 1,168 EJ and 1,274 EJ, with 90% confidence. The statistical distribution of the (conservatively) inferred reservoir temperatures indicates that 5% of these systems have temperatures between 151 and 208 degrees Celsius, 40% of these systems have temperatures between 102 and 151 degrees Celsius, 50% of these systems have temperatures between 60 and 102 degrees Celsius, and 5% of these systems have temperatures between 36 and 60 degrees Celsius. These resources contain massive amounts of thermal energy that could be used in a wide variety of direct applications and power generation projects. Potentially they are important for the economy of 26 of the 32 Mexican States. This work does not include any attempt to estimate the recuperation factor of the estimated resources. [Spanish] En 2003 publicamos nuestra primera estimacion de los recursos geotermicos mexicanos de temperatura intermedia a baja (T {<=} 200 grados centigrados) con base en datos de 1358 manifestaciones superficiales identificadas en ese momento. Debido a falta de informacion en uno o mas parametros relevantes, como coordenadas geograficas, temperatura de muestra o del yacimiento, etc., dicha evaluacion incluyo aproximadamente 30% de las manifestaciones identificadas. Desde entonces nuestro grupo incremento significativamente la cantidad de la informacion en la base de datos, mediante compilacion de datos de diferentes fuentes y trabajo de campo. Posteriormente desarrollamos una base de datos relacional y la implementamos en un Sistema de Informacion Geografica (SIG). En este trabajo presentamos un resumen de nuestra evaluacion 2010 de los recursos geotermicos mexicanos de temperatura intermedia a baja resultante de nuestra base de datos actualizada, que incluye 2361 manifestaciones geotermicas. Como en la version precedente, utilizamos el metodo volumetrico y simulaciones Montecarlo para estimar los recursos geotermicos y sus correspondientes incertidumbres para cada sistema

Geochemical and isotopic behavior of fluids from wells in Los Humeros geothermal field, Puebla, Mexico; Comportamiento geoquimico e isotopico del fluido de los pozos del campo geotermico Los Humeros, Puebla, Mexico

Energy Technology Data Exchange (ETDEWEB)

Tovar Aguado, Rigoberto; Lopez Romero, Oscar [Comision Federal de Electricidad, Los Humeros, Puebla (Mexico)

1999-12-01

In general the wells in Los Humeros geothermal fields produce sodium bicarbonate water with a low salinity because the fluids are produced from the shallow part of the reservoir. The fluids in wells H-33 and H-6 are sodium chloride: the first influenced by fluids from deep levels in the reservoir and the second by fluids coming only from the deeps part of the reservoir. Fluid mixture for other wells depends on operating conditions. To date, it has been difficult with the geothermetric temperatures to establish the underground flow directions and whether or not an infiltration of shallow low-temperature fluids occurs. Well H-16 has the lowest-temperature fluid in the liquid phase, which suggests infiltration of shallow local fluids-a result corroborated by an isotopic study. Using the methodology of Giggenbach and Goguel, we found that the gases are in equilibrium with the liquid phase at temperatures between 275 and 325 Celsius degrees. The maximum temperature is measured in wells H-12 and H-9, where good agreement exists between this temperature and those calculated with a geothermometer of CO{sub 2}/H{sub 2} . Isotopic results show, in general, that the wells with the highest levels of oxygen-18 are those with the highest geothermetric temperatures (CO{sub 2}/H{sub 2})- both in the north (H-35 and H-9) and in the south (H-6 and H-12)-results that agree with the temperatures measured in the field. The initial thermodynamic conditions of the wells show that they produce fluids from the liquid region. This fact, together with the low salinity, permit the application of the D' Amore methodology, with which the estimations of vapor fractions in the reservoir are relatively low. [Spanish] En general, los pozos del campo geotermico de Los Humeros producen agua del tipo bicarbonato sodico con baja salinidad. Esto se debe a que extraen fluidos de la parte somera del yacimiento. Los pozos H-33 y H-6 son clorurados sodicos; el primero por cierta influencia de la zona

Update of the basement model of the Cerro Prieto, B. C., geothermal field, Mexico; Actualizacion del modelo del basamento en el campo geotermico de Cerro Prieto, B.C., Mexico

Energy Technology Data Exchange (ETDEWEB)

Gonzalez Lopez, Macario [Residencia General de Cerro Prieto, Comision Federal de Electricidad, Mexicali, Baja California (Mexico)

1999-04-01

With the aim to actualize the basement model of the Cerro Prieto Geothermal Field, a gravity interpretation has been held. We modeled in 2.5 D, nine profiles traced over the Bouguer anomaly map. Well data concerning lithology and density changes were used to fit the gravity models. Results of this work confirm that the geometry of the basement of Cerro Prieto, corresponds to a structural sequence. From west to east it starts as a big depression, continues with a strong uplift of the basement in the middle sector and finally deepens eastward in steps. The basement model proposed in the present work, defines a similar trend to that established by Fonseca y Razo (1980), but there are differences in basement depth in some areas. In the present model we interpret basement depths between 200 and 400 m deeper than in previous models to the south and northwest of the actual exploitation zone. [Spanish] Con el fin de actualizar el modelo del basamento en el Campo Geotermico de Cerro Prieto, se realizo una reinterpretacion gravimetrica, modelando en 2.5 D, 9 perfiles trazados sobre el mapa de anomalia de Bouguer. Utilizando la informacion litologica obtenida a traves de numerosas perforaciones profundas, se hicieron coincidir, dentro de los mofelos gravimetricos, las principales variaciones litologicas con cambios en la densidad. Los resultados de este trabajo reiteran que la geometria del basamento del Campo de Cerro Prieto, vista de W a E, corresponde con una secuencia estructural que se inicia con una gran depresion en el W, continua con un fuerte levantamiento y finalmente se extiende con una tendencia a profundizarse hacia el E de forma escalonada. El modelo de basamento derivado del presente trabajo, define una tendencia muy similar al modelo de basamento establecido (Fonseca y Razo, 1980), pero difiere en cuanto a la profundidad en algunos sectores del campo. En el actual trabajo se interpreta una profundidad entre 200 y 400 m mayor hacia el sur y noroeste de la

Mineralogy of the silica-epidote mineralized zone (SEMZ) in the Cerro Prieto geothermal reservoir, B.C., Mexico; Mineralogia de la zona mineralizada de silice-epidota (ZMSE) del yacimiento geotermico de Cerro Prieto, B.C., Mexico

Energy Technology Data Exchange (ETDEWEB)

Izquierdo, Georgina; Aragon, Alfonso; Portugal, Enrique; Arellano; Victor M [Instituto de Investigaciones Electricas, Gerencia de Geotermia, Cuernavaca, Morelos (Mexico)]. E-mail: gim@iie.org.mx; Leon, Jesus de; Alvarez, Julio [Comision Federal de Electricidad, B.C. (Mexico)

2006-07-15

The distribution of hydrothermal minerals, mineral assemblages and fluid inclusion data were taken from drill cuttings from the production zone of wells all over the Cerro Prieto geothermal field. The production zone has been termed the silica-epidote mineralized zone (SEMZ), and is located in the deep part of the gray shale where thick layers of sandstone are found. Common mineral assemblages show three temperature ranges in the SEMZ: <200 degrees Celsius, 200-250 degrees Celsius and 250-300 degrees Celsius. The first range is characterized by clays, calcite and quartz; the second by quartz, epidote, chlorite and mica, and the third by epidote, amphibole, illite and chlorite. The study of fluid inclusions in authigenic grain quartz has shown two-phase fluid inclusions (liquid + vapor) of different salinities. A wide range exists of homogenization temperatures (Th) and for some wells there is a good agreement between Th and direct temperature measurements. [Spanish] Se determino la distribucion de minerales hidrotermales y las asociaciones parageneticas y se realizo el estudio microtermometrico de inclusiones fluidas a partir de recortes de perforacion de pozos de las distintas areas del campo geotermico de Cerro Prieto. Las muestras de recortes y nucleos de perforacion estudiados provienen de la zona de produccion a la que se le ha denominado Zona Mineralizada de Silice-Epidota (ZMSE), que se encuentra en la parte profunda de la lutita gris con importantes horizontes de areniscas. En esta zona las asociaciones parageneticas mas comunes han mostrado tres intervalos de temperatura para la ZMSE: <200 degrees Celsius, 200-250 degrees Celsius, 250-300 degrees Celsius. El primer intervalo esta caracterizado principalmente por arcillas, calcita y cuarzo; el segundo por cuarzo, epidota, clorita y micas, y el tercero por epidota, anfiboles, illita y clorita. El estudio de inclusiones fluidas en fragmentos de cuarzo autigenico mostro la presencia de inclusiones de dos fases

MEDICIÓN DEL EQUILIBRIO LIQUIDO-VAPOR DEL SISTEMA METANOL-ACETATO DE METILO A 580 mmHg

Directory of Open Access Journals (Sweden)

Carlos Ariel Cardona

2008-03-01

Full Text Available En este trabajo se midió experimentalmente el equilibrio líquido-vapor para el sistema binario metanol–acetato de Metilo a 580 mmHg. Las mediciones experimentales fueron realizadas utilizando un equipo con recirculación tipo Cottrell. Los datos obtenidos fueron comparados con los resultados adquiridos de la simulación del equilibrio líquido-vapor del sistema bajo estudio. En la simulación se empleó el modelo de actividad NRTL para representar la no idealidad de la fase líquida (con parámetros encontrados en la literatura, y la ecuación de estado de Hayden O´Connel para la no idealidad de la fase vapor. De igual manera, se correlacionaron los datos para encontrar nuevos parámetros del modelo de actividad en NRTL. Además, a partir de datos experimentales medidos a 760 mmHg encontrados en la literatura para el sistema estudiado, se verificó la Ley de Vresky, la cual permite, sin necesidad de cálculos rigurosos, predecir la dirección de desplazamiento de un azeótropo binario cunado se varía la presión del sistema.

Mineralogical and micro-thermometric features of the Los Humeros geothermal reservoir, Pue., Mexico; Caracteristicas mineralogicas y microtermometricas del yacimiento geotermico de Los Humeros, Pue., Mexico

Energy Technology Data Exchange (ETDEWEB)

Izquierdo, Georgina; Arellano, Victor M; Aragon, Alfonso [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: gim@iie.org.mx

2008-07-15

Studies on many topics have been undertaken during the exploratory and exploitation stages of the development of Los Humeros geothermal field. From a geochemical and mineralogical view-including hydrothermal mineralogy and fluid-inclusion micro-thermometry, features have been reported differing from those observed in other geothermal fields. Sometimes this has led to ambiguous conclusions. Studies of fluid-inclusion micro-thermometry have shown low-salinity and high-temperature fluids, suggesting a slight temperature decrease in the deepest portion associated with a boiling process rather than a cooling process. In 1998, Arellano et al. performed a multi-disciplinary study and proposed the existence of at least two, distinct reservoirs at depth. Mineralogical data from wells drilled at the Colapso Central zone tend to support this idea. However wells drilled in the zone known as Corredor Mastaloya seemingly show evidence of a single reservoir. [Spanish] Durante las etapas de exploracion y explotacion del campo geotermico de Los Humeros se han realizado diversos estudios cubriendo distintos topicos. Desde el punto de vista geoquimico y mineralogico (mineralogia hidrotermal y microtermometria de inclusiones fluidas) se han reportado comportamientos diferentes a los observados en otros campos del mundo, los que en ocasiones han llevado a conclusiones imprecisas. La microtermometria de inclusiones fluidas ha mostrado fluidos poco salinos de alta temperatura, asi como una ligera disminucion de temperatura en la parte profunda la cual se asocia a un proceso de ebullicion mas que a un enfriamiento del sistema. En 1998 Arellano et al realizaron un estudio multidisciplinario proponiendo la existencia de al menos dos reservorios. La informacion mineralogica de pozos perforados en la zona del Colapso Central fortalece esta propuesta. Sin embargo, para pozos localizados en la zona conocida como Corredor Mastaloya se tiene evidencia de lo que parece ser un solo yacimiento.

Initial thermal state of the Los Humeros, Puebla, Mexico, geothermal field; Estado termico inicial del campo geotermico de Los Humeros, Puebla, Mexico

Energy Technology Data Exchange (ETDEWEB)

Garcia Gutierrez, Alfonso [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: aggarcia@iie.org.mx

2009-01-15

The initial temperatures field is presented for 40 wells in the Los Humeros geothermal reservoir, along with an elevation curve based on the formation temperature or the most probable reservoir temperature. Stabilized temperatures were estimated using the Radial Spherical Heat Flow method, chosen over the Horner method based on the numerical simulation of the circulation and stop processes of well H-26. In this well, the last temperature log series was reproduced, considering circulation losses. The temperatures were used to produce isothermal curves over three geological sections of the field, which represent the initial distribution of temperatures in the reservoir and show the thermal characteristics and the relationships among thermal anomalies and faults in the reservoir. The elevation curve plotted against the initial temperature of the formation was generated based on detection of the main feed zones at each well, which in turn was developed using detailed analyses of diverse information, such as temperature logs, circulation losses, lithology, well completion, and heat velocities. Based on the results, two groups of wells may be distinguished: one between 1000 and 1600 masl with temperatures from 290 to 330 degrees Celsius, and one between 900 and 0 masl with temperatures from 300 to 400 degrees Celsius. [Spanish] En este trabajo se presenta el campo de temperatura inicial del yacimiento geotermico de Los Humeros y una curva de elevacion contra la temperatura de formacion o temperatura mas probable del yacimiento, obtenida para 40 pozos del campo. Las temperaturas estabilizadas se estimaron mediante el metodo de Flujo de Calor Esferico Radial, y su eleccion sobre las temperaturas del metodo de Horner se soporta con simulacion numerica de los procesos de circulacion y paro del pozo H-26, en la cual la ultima serie de registros se reprodujo considerando perdidas de circulacion. Con estas temperaturas se generaron curvas isotermicas para tres secciones

Study of liquid and steam tracers at the Maritaro - La Cumbre area of the Los Azufres geothermal field, Mich.; Estudio con trazadores de liquido y vapor en la zona Maritaro - La Cumbre del campo geotermico de Los Azufres, Mich.

Energy Technology Data Exchange (ETDEWEB)

Iglesias, Eduardo R [Instituto de Investigaciones Electricas, Cuernavaca, Morelos, (Mexico)]. E-mail: iglesias@iie.org.mx; Flores Armenta, Magaly; Quijano Leon, Jose Luis; Torres Rodriguez, Marco A [Comision Federal de Electricidad, Morelia, Michoacan (Mexico); Torres, Rodolfo J; Reyes Picasso, Neftali [Instituto de Investigaciones Electricas, Cuernavaca, Morelos, (Mexico)

2008-01-15

We ran two simultaneous tracer tests in the Maritaro-La Cumbre area of the Los Azufres geothermal field in Mexico. We wished to determine whether or not fluids injected in well Az-15 recharged the productive areas of six production wells and to estimate the fractions of injected fluid recovered in them, if any. Because only three of the wells produce water and all of them produce steam, two tracers were used, sulfur hexafluoride (SF{sub 6}) for the gas phase and 1,3,6 naphthalene trisulfonate (1,3,6-nts) for the liquid phase. All of the observation wells recorded SF{sub 6}, and the three water-producing wells recorded 1,3,6-nts, proving that fluids injected in well Az-15 do recharge the area of interest. When sampling was suspended, the three water-producing wells were still producing 1,3,6-nts at significant rates. The total recovery of 1,3,6-nts at wells Az-65D, Az-04 and Az-28, 279 days after injection when sampling was halted, were, respectively, 6.1%, 0.90% y 0.16%, for a total of 7.61%. We concluded that these quantities constitute the lower boundaries for the respective recovery factors. When sampling was halted, wells Az-65D, Az-66D and Az-30 were still producing some SF{sub 6} at lower rates, and the rest of the wells were no longer recording the gas phase tracer. The total recovery of SF{sub 6} at wells Az-65D, Az-04, Az-41, Az-30, Az-28 and Az-66D were, respectively, 4.82 e-02%, 1.37 e-03%, 1.48 e-03%, 6.38 e-04%, 1.38 e-03% y 4.31 e-04%, for a total of 5.35 e-02%. The liquid recharge occurred in orders of magnitude greater than the steam. [Spanish] Se efectuaron dos pruebas simultaneas en la zona Maritaro-La Cumbre del campo geotermico de Los Azufres, Mich., Mexico. Los objetivos de estas pruebas fueron determinar si la salmuera de desecho inyectada en el pozo Az-15 recarga las zonas de alimentacion de seis pozos productores designados por CFE, y estimar que fraccion de lo inyectado recarga dichos pozos productores. Debido a que solo tres de los pozos

Studies for recovering injection capacity in wells of the Cerro Prieto, BC, geothermal field; Estudios para recuperar la capacidad de aceptacion en pozos inyectores del campo geotermico de Cerro Prieto, BC

Energy Technology Data Exchange (ETDEWEB)

Alvarez Rosales, Julio [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Residencia General de Cerro Prieto, Mexicali, Baja California (Mexico)]. E-mail: julio.alvarez@cfe.gob.mx

2010-01-15

As in geothermal fields around the world, at Cerro Prieto geothermal field, Baja California, former exploratory and production wells are used to inject residual brine. Since the 1980s, studies and activities have been carried out to find ways to recharge the reservoir and dispose of brine without harming the environment or underground aquifers. These include infiltration and cold-and-hot injection. Some of the studies are presented here, including analyses of litho-facies; core samples; pressure, temperature and spinner logs; well tests and injection rates-plus some studies on the shallow aquifer. All have been useful in fulfilling requirements made by environmental authorities. Because injection rates constantly decrease due to formation damage, it is proposed an additional technique be used to reduce such damages and prolong the lifetime of cold-and-hot injection wells-while ensuring the environment and shallow aquifers are not affected. [Spanish] Al igual que en diversos campos geotermicos en el mundo, en el de Cerro Prieto, Baja California se han utilizado tanto pozos inyectores perforados ex profeso como antiguos pozos exploratorios y productores para inyectar el fluido residual al subsuelo. Desde la decada de los 80 se han realizado diversos estudios y acciones en ese campo geotermico para recargar al yacimiento y para disponer del fluido residual, sin ocasionar danos al ambiente ni a los cuerpos hidricos del subsuelo, que van desde la infiltracion hasta la inyeccion en frio y en caliente. Este articulo presenta los diferentes estudios realizados con ese objetivo en el campo, incluyendo el analisis de litofacies, de nucleos de formacion, de registros de presion, temperatura y spinner, las pruebas en pozos y analisis de tasas de aceptacion, asi como los efectuados en el acuifero superficial. Todos ellos han sido de utilidad para atender los requerimientos de las autoridades ambientales. Finalmente, y en virtud de que las tasas de aceptacion de los pozos

Scaling control in superficial installations at the Las Tres Virgenes, geothermal field, BCS; Control de incrustacion en instalaciones superficiales del campo geotermico de Las Tres Virgenes, BCS

Energy Technology Data Exchange (ETDEWEB)

Tapia Salazar, Ruth [Comision Federal de Electricidad (Mexico)]. E-mail: ruth.tapia@cfe.gob.mx

2007-01-15

podian ofrecer mejores resultados, tomando en cuenta las condiciones del campo. Se adopto finalmente la tecnica de modificacion del pH de la salmuera, dando como resultado que, a un ano de su puesta en operacion en el sistema general de inyeccion, no haya habido necesidad de realizar ninguna limpieza mecanica a las tuberias, lo que anteriormente se realizaba cada tercer dia como minimo. Esto constituye una importante mejora al sistema de suministro de vapor.

Application of heating in dex in Los Humeros geothermal reservoir; Comportamiento de los indices de calentamiento en el yacimiento geotermico de los Humeros

Energy Technology Data Exchange (ETDEWEB)

Aragon, Alfonso; Arellano, Victor M; Izquierdo, Georgina; Garcia, Alfonso; Barragan, Rosa Maria; Verma, Mahendra P [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico); Pizano, Arturo [Comision Federal de Electricidad, Los Humeros (Mexico)

2000-12-01

: volumen de perdidas de circulacion, litologia, velocidades de penetracion, etc. Este metodo es usado para identificar las caracteristicas de interes de los intervalos de la formacion en cada pozo tanto para la explotacion como para inyeccion. Como una calibracion previa del metodo se utilizaron datos del pozo Br-2, del campo geotermico de Boadlands en Nueva Zelandia. Posteriormente con datos de los pozos H-11, H-31, y H-33 del campo geotermico de Los Humeros, en Mexico, fue factible determinar el comportamiento de los indices de calentamiento, orientando de esta manera su utilidad a los analisis del yacimiento.

Criteria to determine the depth of the production interval in wells of the Cerro Prieto geothermal field, Mexico; Criterios para determinar la profundidad del intervalo productor en pozos del campo geotermico de Cerro Prieto, Mexico

Energy Technology Data Exchange (ETDEWEB)

Leon Vivar, Jesus Saul de [Comision Federal de Electricidad, Residencia General de Cerro Prieto, Mexicali, B.C. (Mexico)]. E-mail: jesus.deleon@cfe.gob.mx

2006-07-15

Ways to select the depth of the production interval or to complete wells in the Cerro Prieto geothermal field have changed during the development of the field. From 1961 when drilling began to the middle of 2005, a total of 325 wells were drilled. The paper compares the approaches used in the past with those of the last ten years. The Cerro Prieto system has been classified as being of liquid-dominated and high-temperature. Today, after 33 years of commercial exploitation, it has experienced a series of thermal and geochemical fluid changes making it necessary to modify the ways to select the depth of the well production intervals, according to the observed behavior of the reservoir. The new criteria include the thermal approach, the geological approach, the geochemical approach and a comparative approach with neighboring wells. If most of these criteria are interpreted correctly, the success of a well is ensured. [Spanish] Los criterios para seleccionar la profundidad del intervalo productor o la terminacion de los pozos en el campo geotermico de Cerro Prieto han cambiado durante el desarrollo del mismo. De 1961, cuando se perforaron los primeros pozos, hasta mediados del 2005 se han perforado un total de 325 pozos. En el presente articulo se hara una breve revision de cuales han sido los criterios usados en el pasado y los que se han venido empleando en los ultimos diez anos. El yacimiento de Cerro Prieto ha sido clasificado como de liquido dominante, de alta temperatura, pero actualmente, despues de 33 anos de explotacion comercial, ha sufrido una serie de cambios termicos y geoquimicos en sus fluidos, por lo que ha sido necesario modificar los criterios para seleccionar la profundidad del intervalo productor de los pozos de acuerdo al comportamiento observado en el yacimiento. Los criterios actuales se dividen en cuatro: 1. Criterio termico, 2. Criterio geologico, 3. Criterio geoquimico y 4. Criterio comparativo de los pozos vecinos. Cuando la mayoria de estos

Analysis of productive evolution of well M-19A, Cerro Prieto geothermal field, BC; Analisis de la evolucion productiva del pozo M-19A del campo geotermico de Cerro Prieto, BC

Energy Technology Data Exchange (ETDEWEB)

Rodriguez-Rodriguez, Marco H; Romero-Rios, Francisco [Comision Federal de Electricidad, Residencia General de Cerro Prieto, B.C (Mexico)]. E-mail: marco.rodriguez01@cfe.gob.mx

2007-07-15

Well M-19A has been the most productive in the Cerro Prieto field, producing around 40 million tons of fluid. The well went on line in February 1975 and was in continuous operation until June 2006. Monthly measurements for over 30 years of operating conditions and chemical and isotopic analyses of the fluids allow identification of the most significant processes occurring in the zone where the well is located. Three dominant recharge types have been identified, each lasting about 10 years. They are a) a recharge of fluids of lower temperature than the production fluids, even though the chemical and isotopic compositions are similar; b) a recharge of lower-temperature fluids with diluted chemical and isotopic compositions; and c) a progressive recharge of reinjected water with a higher chloride concentration and heavy isotopic composition. The production and reinjection rates for over 30 years of production history in the M-19A well zone allow for speculation of a reservoir pressure recovery, which is confirmed with a calculation using production data from well M-19A. The evolution of the reservoir pressure in the zone contrasts with the rest of the reservoir, where a constant pressure drop is observed, particularly toward the central and eastern parts of the field. [Spanish] El pozo M-19A ha sido el mas productivo del campo geotermico de Cerro Prieto, BC, alcanzando una extraccion de mas de 40 millones de toneladas de fluido. Fue integrado a produccion en febrero de 1975 y hasta junio de 2006 ha permanecido en produccion en forma continua. Las mediciones mensuales de sus condiciones operativas y los analisis quimicos e isotopicos del agua producida permiten identificar los procesos mas significativos que han ocurrido a lo largo de esos mas de 30 anos en la zona donde se localiza el pozo. Se han identificado tres tipos de recarga dominantes que se presentan durante un periodo cercano a 10 anos cada uno, los cuales son: a) una recarga de fluidos de menor temperatura

Modification of the water-level control system at the Unit 12 of Los Azufres, Mich., geothermal field; Modificacion del sistema de control de nivel de agua en la Unidad 12 del campo geotermico de Los Azufres, Mich.

Energy Technology Data Exchange (ETDEWEB)

Tello Hinojosa, Raul; Aburto Huerta, S. Ramon; Mendoza Covarrubias, Hector M [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)]. E-mail: raul.tello@cfe.gob.mx

2007-01-15

Unit 12 of the Los Azufres, Mich., geothermal field is a binary cycle unit of 1.45 MW, installed at the pad of production well Az-22. There are two separators on this pad. One separates the mix extracted from well Az-22 and the other from adjacent wells. The separated brine from both separators is gathered in a horizontal tank and sent to Unit 12. The steam is sent to Unit 7, which generates 50 MW. Once some interference occurred affecting the power generation of Unit 7 when Unit 12 was off line. This was caused by the original flow arrangement and water-level control system. To avoid interference, a water-level control system was designed and installed in the separators. The system operates independently of Unit 12, with tanks in each separator connected by a pipe. Regulation of the water level is accomplished by three motor valves and a level sensor. To ensure permanent feeding of electrical power to the valves, an automatic system was installed from transmission lines of 23 and 115 kV. In case both lines fail, there is an uninterrupted power supply (UPS) unit. At the beginning of 2005, Unit 12 was again online with a modified water-level control system that has operated satisfactorily since then. Its short periods offline have not affected Unit 7. [Spanish] La Unidad 12 del campo geotermico de Los Azufres, Mich., es una unidad de ciclo binario de 1.45 MW, instalada en la plataforma del pozo productor Az-22. En esta plataforma hay dos separadores, uno de los cuales separa la mezcla extraida del pozo Az-22 y el otro la de varios pozos aledanos. El agua separada de ambos se concentra en un tanque horizontal y de este pasa a la Unidad 12, mientras que el vapor se envia a la Unidad 7, de 50 MW. Por el tipo de arreglo original de flujo y control de nivel de agua en los equipos, ocurrian interferencias que provocaban que cuando la Unidad 12 se disparaba se afectara la generacion en la Unidad 7. Para evitar esta interferencia se diseno e instalo un sistema de control de

A reverse method to estimate initial temperatures in geothermal reservoirs; Un metodo inverso para estimacion de la temperatura inicial de yacimientos geotermicos

Energy Technology Data Exchange (ETDEWEB)

Garcia Gutierrez, Alfonso [Instituto de Investigaciones Electricas, Gerencia de Geotermia, Cuernavaca, Morelos (Mexico)]. E-mail: aggarcia@iie.org.mx; Ramos Alcantara, Jose R. [Centro Nacional de Investigacion y Desarrollo Tecnologico, Departamento de Ingenieria Mecanica, Cuernavaca, Morelos (Mexico); Arellano Gomez, Victor M. [Instituto de Investigaciones Electricas, Gerencia de Geotermia, Cuernavaca, Morelos (Mexico)

2010-01-15

A method is presented for estimating the initial temperature in geothermal-reservoir formations. The method is based on control theory where the measured temperatures or temperature logs are compared with corresponding simulated temperatures for different times with the well closed. The comparison is made using a control algorithm that makes changes to the originally assumed reservoir temperatures and performs iterations until the best fit between the temperature logs and the simulated temperatures is obtained. The simulation of fluid transport and heat in the well includes the processes of circulation and stop in the presence of circulation losses, modeled on macroscopic balances of momentum and energy. The transport processes in the formation regard the reservoir as an isotropic porous medium and fluid flow is described by Darcy's law. This model generates the fields of temperatures, pressures and speeds as a function of time and space. The method was tested with data from well LV-3 in Las Tres Virgenes geothermal field, Baja California Sur, Mexico. The estimated temperatures of the undisturbed formation-or initial temperatures-are compared within {+-}15 degrees Celsius with the measured temperatures, which is an acceptable outcome from an engineering point of view. [Spanish] Se presenta un metodo para la estimacion de la temperatura inicial en las formaciones de yacimientos geotermicos. El metodo se basa en la teoria de control donde las temperaturas medidas o registros de temperatura se comparan con las correspondientes temperaturas simuladas a diferentes tiempos con el pozo cerrado. La comparacion se hace usando un algoritmo de control el cual hace cambios a las temperaturas de yacimiento originalmente supuestas y realiza iteraciones hasta que se obtiene el mejor ajuste entre los registros de temperatura y las temperaturas simuladas. La simulacion del transporte de fluidos y calor en el pozo incluye los procesos de circulacion y paro en presencia de

Seismic monitoring during acid stimulation of wells LV-4 and LV-13 at the Las Tres Virgenes geothermal field, BCS, Mexico; Monitoreo sismico durante la estimulacion acida de los pozos LV-4 y LV-13 del campo geotermico de Las Tres Virgenes, BCS, Mexico

Energy Technology Data Exchange (ETDEWEB)

Venegas Salgado, Saul; Arredondo Fragoso, Jesus; Ramirez Silva, German; Flores Armenta, Magaly; Ramirez Montes, Miguel [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)]. E-mail: magaly.flores@cfe.gob.mx

2006-07-15

ubican dentro de la zona geotermica de mayor importancia a profundidades del orden de 0.4 a 4 km y magnitudes pequenas tipicas (0.7 a 2.2 Md), lograndose definir dos zonas de importancia asociadas, la primera, al sistema de fallas El Volcan (Zona A) y la segunda al pozo inyector LV-8 (Zona B). En la zona A, el efecto de la induccion y puesta en marcha de los dos pozos estimulados con una mayor produccion de vapor el 30 de octubre y 17 de noviembre de 2004, aumento la actividad sismica hasta un maximo de 12 sismos por dia a principios de diciembre. En la zona B, el efecto del inicio del enfriamiento de los dos pozos cambio el numero de sismos que se originan en ella, ya que se observo un aumento de 6 sismos por dia el 2 de octubre, disminuyendo dias despues. Por otro lado, tambien se observo un aumento de la actividad sismica despues de la induccion y puesta en produccion nuevamente de los dos pozos productores, registrandose un maximo de 11 sismos por dia a fines de noviembre. Finalmente, de acuerdo a la distribucion sismica, se puede concluir que los sistemas de fallas mas activos son los de El Volcan y El Viejo. Las nuevas propuestas de perforacion de pozos productores en este campo geotermico estan apoyadas en estos resultados.

Study with a steam tracer in a zone near well Az-64, in the Los Azufres geothermal field, Mich.; Estudio con un trazador de vapor en la zona aledana al pozo Az-64, en el campo geotermico de Los Azufres, Mich.

Energy Technology Data Exchange (ETDEWEB)

Iglesias, Eduardo R. [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: iglesias@iie.org.mx; Flores Armenta, Magaly; Quijano Leon, Jose Luis; Torres Rodriguez, Marco A. [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico); Torres, Rodolfo J.; Reyes Picasso, Neftali [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Sandoval Medina, Fernando [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)

2009-01-15

and 539 m from the injector. The results showed the six monitored wells are recharged from injection in Az-64 and quantified the corresponding recoveries as steam. Because only a steam-phase tracer was used, we were unable to determine liquid-recovery amounts. The work also allowed us to characterize relations between the permeability in the studied zone and the known distribution of faults. Some relationships were suggested unconsidered before. [Spanish] En el estudio con trazadores precedente a este, efectuado en la zona Maritaro-La Cumbre del campo geotermico de Los Azufres, Mich., se comprobo que la inyeccion en el pozo Az-15 recarga a un grupo de pozos situados a una distancia maxima del inyector de algo menos de 2000 m. Y se comprobo que la inyeccion en dicho pozo o bien no recarga a pozos situados a mas de 2300 m hacia el este, en las inmediaciones de la falla Laguna Verde, o lo hace muy lentamente en un largo periodo. Como es importante recargar la zona mencionada en ultimo termino, se decidio entonces explorar la posibilidad de recargarla desde el pozo Az-64, localizado en dicha area. Para ello se diseno el presente estudio. Se designaron seis pozos productores para monitorear el arribo del trazador. Debido a que todos estos pozos producen vapor (aunque varios producen tambien liquido), y por consideraciones economicas, se decidio utilizar en este caso un trazador de vapor solamente. Se utilizo hexafluoruro de azufre (SF6), un trazador utilizado con exito previamente en este campo. El 24 de octubre de 2006 se inyectaron 96.4 kg de SF6 en el pozo Az-64. El monitoreo de los pozos se realizo durante 156 dias a partir de esa fecha. El trazador se detecto en los seis pozos productores monitoreados. En todos los casos las formas de las curvas de residencia manifestaron claramente la naturaleza fracturada de la permeabilidad involucrada. En todos los casos las curvas de recuperacion del trazador indicaron claramente que la llegada del mismo se habia completado

Two-phase characteristics of the feeding fluid of Cerro Prieto IV wells (Mexico) obtained by gas equilibrium; Caracteristicas bifasicas del fluido de alimentacion de pozos de Cerro Prieto IV (Mexico), obtenidas por equilibrio gaseoso

Energy Technology Data Exchange (ETDEWEB)

Barragan-Reyes, Rosa Maria; Arellano-Gomez, Victor Manuel; Portugal-Marin, Enrique [Instituto de Investigaciones Electricas (Mexico); De Leon-Vivar, Jesus [Comision Federal de Electricidad, Residencia General de Cerro Prieto, B.C (Mexico)

2008-10-15

The gas composition of fluids produced by CP IV geothermal wells from the Cerro Prieto field was studied in order to identify different types of fluids entering the wells by estimating their temperature and excess steam. A method based on the Fischer Tropsch reaction and H2S equilibrium with pyrite-pyrrhotite as mineral buffer (FTHSH3) was used. The results for the reservoir natural state indicated the presence of fluids with heterogeneous reservoir temperature (between 275 and 310 degrees Celsius) and excess steam values, which were found from negative (boiled liquid that has lost steam when flowing to the well) to one (steam phase with zero liquid saturation). The study for individual wells in which boiling processes were identified, showed that through time, the feeding fluids consist of a two-phase mixture with different liquid/steam proportions. Also, the results suggested that a steam phase could occur at CP IV which is added to the feeding fluid, depending on the operation conditions of the wells. The origin of this steam could be the boiling of the deeper liquid due to a pressure drop. [Spanish] Se estudio la composicion gaseosa de los fluidos producidos por pozos geotermicos del sector CP IV del campo de Cerro Prieto para tratar de distinguir aportes de fluidos diferentes mediante la estimacion de su temperatura de yacimiento y del exceso de vapor. Se utilizo un metodo de equilibrio gaseoso basado en la reaccion de Fischer Tropsch y el equilibrio combinado pirita-pirrotita (FT-HSH3). Los resultados obtenidos indican que en el estado inicial del yacimiento existen fluidos que muestran heterogeneidad en los valores de temperatura de yacimiento (entre 275 y 310 grados Celsius), asi como en el exceso de vapor con valores desde negativos (liquido que despues de ebullir ha perdido vapor en su trayecto hacia el pozo) hasta uno (vapor con cero saturacion de liquido). El estudio individual de los pozos con fenomenos de ebullicion muestra que a traves del tiempo

Code for the steam tables for pure water in visual basic 6.0.; Un codigo para las tablas de vapor para agua pura en visual basic 6.0

Energy Technology Data Exchange (ETDEWEB)

Verma, Mahendra P. [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2002-07-01

The thermodynamic data of the water are of extreme importance in all of the branches of science and technology; the facilitate the understanding of the natural Earth processes. Nevertheless, for the electrical industry the water plays a very important role during the generation of electrical energy process. Different heat sources such as coal, oil, natural gas, nuclear fuel or the geothermal heat boil the water that forms the steam used to move the turbines. Consequently, the steam tables (the thermodynamic water data) are vital to model thermal and mass transference and physical-chemical processes during the generation of electrical energy. [Spanish] Los datos termodinamicos del agua son de suma importancia en todas las ramas de la ciencia y tecnologia, ellos facilitan el entendimiento de los procesos naturales de la Tierra. Sin embargo, para la industria electrica el agua juega un papel muy importante durante el proceso de generacion de energia electrica. Diferentes fuentes de calor tales como carbon, aceite, gas natural, combustible nuclear o el calor geotermico calientan el agua que forma el vapor utilizado para mover las turbinas. Luego entonces, las tablas de vapor (los datos termodinamicos de agua) son vitales para modelar transferencia termica y de masa y procesos fisico-quimico durante la generacion energia electrica.

Geothermics and neural networks: A first approach; Geotermia y redes neuronales: Una primera aproximacion

Energy Technology Data Exchange (ETDEWEB)

Flores Armenta, Magaly del Carmen [Gerencia de Proyectos Geotermoelectricos de la Comision Federal de Electricidad, Morelia (Mexico); Barragan Orbe, Carlos [Comision Federal de Electricidad, Mexico, D. F. (Mexico)

1995-09-01

Neural networks have been hailed as the greatest technological advance since the transistor. They are predicted to be a common household item by the year 2000. This new form of machine intelligence is able to solve problems, without using rules of math, they only need examples to learn from. The first geothermal problem, to solve with this powerful tool, is the prediction of liquid and steam production, as well as the well`s termination in Los Humeros, Puebla, Mexico. The first attempt shows the learning`s capacity of the developed model, and its precision on the predictions that were done. [Espanol] Las redes neuronales se consideran como uno de los mas grandes avances tecnologicos desde la invencion del transistor, de tal forma que se perfilan como una de las herramientas mas comunes del ano 2000. Esta nueva forma de inteligencia artificial es capaz de resolver problemas sin utilizar reglas matematicas, solamente requiere de ejemplos para aprender de ellos. El primer problema geotermico, atacado con esta poderosa herramienta, es la prediccion de las producciones de vapor y liquido, asi como la terminacion de pozos en el campo geotermico de Los Humeros, Puebla, Mexico. Los primeros intentos demuestran la capacidad de aprender del modelo desarrollado, y su certeza en las predicciones realizadas.

Initial distribution of pressure and temperature in the geothermal field of Los Humeros, Puebla; Distribucion inicial de presion y temperatura del campo geotermico de Los Humeros, Puebla

Energy Technology Data Exchange (ETDEWEB)

Arellano Gomez, Victor M.; Garcia Gutierrez, Alfonso; Barragan Reyes, Rosa Maria; Aragon Aguilar, Alfonso; Pizano, Arturo [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

2000-07-01

In order to infer the distributions of non disturbed pressure and temperature of the reservoir fluid, a considerable amount of information originating from several disciplines was analyzed, corresponding to 42 wells of the geothermal field of Los Humeros. On the base of the analyzed data models were developed, in one and two dimensions, of the reservoir in an initial state. The models reveal the existence of at least two reservoirs. The first one and most superficial is located between 1600 and 1025 m.a.s.l. and it is a reservoir of dominant liquid. The pressure profile of this reservoir corresponds to a boiling water column approximately between 300 and 339 Celsius degrees. The second reservoir is located underneath the 850 m.a.s.l. and as far as the collected data, it can be said that it extends at least until the 100 m.a.s.l and it is estimated that it is a reservoir of low liquid saturation. For the wells that are fed from this zone of the field temperatures between 300 and 400 Celsius degrees were estimated. A table of the geology of the subsoil of the region of the Los Humeros is shown and a table where the chemical composition of the separated water is indicated and the enthalpy of some of the wells of Los Humeros, Puebla, Mexico. [Spanish] Para inferir las distribuciones de presion y temperatura no perturbadas del fluido del yacimiento, se analizo una considerable cantidad de informacion proveniente de varias disciplinas, correspondiente a 42 pozos del campo geotermico de Los Humeros. Sobre la base de los datos analizados se desarrollaron modelos, en una y dos dimensiones, del yacimiento en un estado inicial. Los modelos revelan la existencia de cuando menos dos yacimientos. El primero y mas superficial se encuentra localizado entre 1600 y 1025 m.s.n.m. y es un yacimiento de liquido dominante. El perfil de presion de este yacimiento corresponde a una columna de agua en ebullicion aproximadamente entre 300 y 339 grados centigrados. El segundo yacimiento se

Estimation of the electric potential at Los Humeros, Puebla, Mexico; Estimacion del potencial electrico del yacimiento de los Humeros, Puebla, Mexico

Energy Technology Data Exchange (ETDEWEB)

Morales Solano, Nora Blanca [Comision Federal de Electricidad, Perote, Veracruz (Mexico)

2000-12-01

The evaluation of the electric potential of geothermal reservoir allows us to estimate the stored energy and the maximum power that could be installed at determined time. The method that was employed for the evaluation is that gradual pressure depletion of the reservoir. It consists of decompressing the system until an abandonment pressure or predetermined time of exploitation is reached. Results indicate that it is possible to generate more than 250 MW during 20 years. [Spanish] La evaluacion del potencial electrico del yacimiento geotermico permite estimar la energia recuperable y la potencia maxima que se puede instalar en un tiempo determinado. El metodo que se empleo para la evaluacion es el de descompresion gradual del yacimiento, que consiste en despresurizar el sistema hasta llegar a una presion de abandono de explotacion predeterminado, y calcular cual es la maxima potencia electrica del yacimiento bajo tales condiciones. El resultado indica que en Los Humeros es posible generar mas de 250 MW durante 20 anos.

Estimation of the resource and technological prospective of geothermal energy in Mexico (Annexe 3 in 'A vision of year 2030 on the use of the renewable energies in Mexico'); Estimacion del recurso y prospectiva tecnologica de la geotermia en Mexico (Anexo 3 en 'Una vision al 2030 de la utilizacion de las energias renovables en Mexico')

Energy Technology Data Exchange (ETDEWEB)

Iglesias R, Eduardo; Arellano G, Victor; Torres R, Rodolfo Joaquin [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2005-08-15

Due to its individual geologic-structural characteristics, Mexico counts on abundant geothermal resources. At the moment we count on a database that includes 2,332 geothermal manifestations distributed in 27 of the 32 Mexican states, the geothermal resources are classified as high temperature and intermediate or low temperature resources. Those of high temperature can be used for the generation of electrical energy. Those of intermediate to low temperature are more appropriate for direct applications of the geothermal heat. As of today, in Mexico exist four geothermal fields of high temperature that are being exploded for the electrical generation. [Spanish] Debido a sus particulares caracteristicas geologico-estructurales, Mexico cuenta con abundantes recursos geotermicos. Actualmente contamos con una base de datos que incluye 2,332 manifestaciones geotermicas distribuidas en 27 de los 32 estados mexicanos, los recursos geotermicos se clasifican en de alta temperatura y recursos de temperatura intermedia a baja. Los de alta temperatura pueden utilizarse para la generacion de energia electrica. Los de temperatura intermedia a baja son mas apropiados para aplicaciones directas del calor geotermico. Actualmente en Mexico existen cuatro campos geotermicos de alta temperatura que estan siendo explotados para la generacion electrica.

Geochemical characteristics of water from the reservoir of the hydrothermal system of Las Tres Virgenes, Baja California Sur, Mexico; Caracteristicas geoquimicas de las aguas del reservorio del sistema hidrotermal actual de Las Tres Virgenes, Baja California Sur, Mexico

Energy Technology Data Exchange (ETDEWEB)

Gonalez Partida, Eduardo [Universidad Nacional Autonoma de Mexico (Mexico); Tello Hinojosa, Enrique [Comision Federal de Electricidad (Mexico); Pal Verma, Mahendra [Instituto de Investigaciones Electricas (Mexico)

2001-03-01

The Las Tres Virgenes geothermal field is a liquid dominated system. The separated produced by the wells are sodium-chloride type, which is a characteristic of totally equilibrated geothermal brine. The temperature of water-rock interaction in the reservoir is 280 Celsius degrees. the chemical composition of gases corresponds to the one expected in a geothermal environment. The CO{sub 2} is the predominating gas and it is superior in 90% in weight to the total of existing gases. The gas contents is less than 1% in weight, in the case of the wells LV-1 and LV-3. It is also possible to conclude that the gases are in equilibrium with the liquid phase at a temperature of 280 Celsius degrees. With respect to water quality, it is saline, from high to very high and the contents of exchangeable sodium is also very high, resulting in waters not fit for agricultural usage. [Spanish] El yacimiento geotermico de Las Tres Virgenes, en Baja California Sur, Mexico, es un sistema de liquido dominante, en donde el agua separada producida por los pozos presenta un caracter clorurado-sodico caracteristico de una salmuera de origen geotermico totalmente equilibrada. El sistema agua-roca se encuentra en equilibrio a una temperatura de 280 grados centigrados , dicha temperatura son congruentes con las estimadas para las fases gaseosas y liquidas. La composicion quimica de los gases corresponde a la esperada en un ambiente geotermico. El CO{sub 2} es el predominante y es superior a 90% en peso del total de los gases presentes. El contenido de gas es menor de 1% en peso en el caso de los pozos LV-1 y LV-3. Tambien se puede concluir que los gases estan en equilibrio en las fases liquidas a una temperatura de 280 grados centigrados. Con respecto a la calidad del agua, presenta una salinidad de alta a muy alta y el contenido de sodio intercambiable tambien es muy alto, por lo que dichas aguas no son muy aptas para el cultivo.

Steam regulation for 5 MW back-pressure units when a failure occurs in the Los Humeros, Pue., field, Mexico; Regulacion del vapor en caso de falla a unidades a contrapresion de 5 MW en el campo de Los Humeros, Pue., Mexico

Energy Technology Data Exchange (ETDEWEB)

Rosales Lopez, Cesar [Comision Federal de Electricidad, Puebla (Mexico)]. E-mail: cesar.rosales@cfe.gob.mx

2006-07-15

Four out of the seven back-pressure power units of 5 MW operating in the Los Humeros geothermal field, State of Puebla, Mexico, are fed by one steam pipe gathering the steam produced by nine wells. When a failure occurred in any of the units and the excedence valve had to be open to deviate the steam, a decrease in the steam flow for the remaining units was noted, along with lower electrical generation. The cause for that is analyzed and explained in this paper by comparing the interconnected steam supply system to an electric circuit. A way to maintain a uniform and continuous supply of steam in the Los Humeros field has been found. It was implemented several months ago and the problem has not reoccurred. [Spanish] Cuatro de las siete unidades de 5 MW a contrapresion que operan en el campo geotermico de Los Humeros, Puebla, son alimentadas por un solo vaporducto que reune el vapor de nueve pozos productores. Cuando ocurria una falla en alguna de estas unidades y se abria por completo la valvula de excedencia para desviar el vapor, se observaba una reduccion en el flujo de vapor que llegaba a las otras tres unidades, lo que a su vez ocasionaba que la generacion de electricidad se redujera notoriamente. En este trabajo se analiza y explica la causa de ello, mediante la comparacion de este sistema interconectado de suministro de vapor con un circuito electrico, y se explica la solucion que se encontro e implemento en el campo de Los Humeros para regular el suministro continuo y uniforme de vapor, con resultados satisfactorios a varios meses de su implementacion en las cuatro unidades interconectadas.

Spatial analysis of noise emission at the Los Azufres geothermal field, Mich.; Analisis espacial de emision de ruido en el campo geotermico de Los Azufres, Mich.

Energy Technology Data Exchange (ETDEWEB)

Camarena Magana, Emilio; Ordaz Mendez, Christian A. [Comision Federal de Electricidad, Residencia de Los Azufres, Morelia, Michoacan (Mexico)]. E-mail: emilio.camarena@cfe.gob.mx

2010-01-15

To verify noise emissions from the usual activities in an operating geothermal field, noise measurements were carried out in a 4.2 km{sup 2} area in the southern zone of the Los Azufres, Mich., geothermal field. There are seven production wells operating here and three abandoned wells. The average noise emission in the southern zone was 36.5 decibels (dB), regarded as the natural reading of environmental-noise emission. In the Christmas (valves) tree for operating production wells, the noise ranges from 70.9 to 91.7 dB, while in open discharging valves for steam-pipes, the noise can reach 118 dB. In Mexico the maximum permissible limit of noise on the periphery of a property is 68 dB in daytime and 65 dB at night. Based on measurements made at the periphery of lots where the geothermal wells are located, four out of seven production wells measured do not exceed the maximum allowable level, while the other three seem to exceed it. However no definite limits exist for the lots. It is recommended that the measurement points as indicated by the official standard in environmental matters be re-established, which will enable noise emissions by several wells that have exceeded the permissible limit, to actually fall within it. [Spanish] Se realizaron mediciones sonicas en un area de 4.2 km{sup 2} localizada en la zona sur del campo geotermico de Los Azufres, Mich., a fin de verificar la emision de ruido asociada a las actividades usuales en un campo geotermico en operacion. En esta area se encuentran siete pozos productores en operacion y tres pozos abandonados. La emision promedio de ruido en estos ultimos fue de 36.5 decibeles (dB), considerandose como la condicion natural de emision de ruido ambiental. En el arbol de valvulas de los pozos productores en operacion el ruido va de los 70.9 a los 91.7 dB, mientras que en valvulas abiertas de descarga de vaporductos la emision puede llegar hasta los 118 dB. En Mexico el limite maximo permisible de ruido en la periferia de

Initial isotopic geochemistry ({delta} 18 O, {delta} D) of fluids from wells of the Los Humeros, Pue., geothermal field; Geoquimica isotopica ({delta} 18 O, {delta} D) inicial de fluidos de pozos del campo geotermico de Los Humeros, Pue.

Energy Technology Data Exchange (ETDEWEB)

Barragan Reyes, Rosa Maria; Arellano Gomez, Victor Manuel [Instituto de Investigaciones Electricas, Gerencia de Geotermia, Cuernavaca, Morelos (Mexico)]. E-mail: rmb@iie.org.mx; Ramirez Montes, Miguel; Tovar Aguado, Rigoberto [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)

2010-01-15

Isotopic data ({delta} 18 O, {delta} D) from fluids from production wells at the Los Humeros, Pue., geothermal field were analyzed to investigate the possible origin of these fluids and the dominant processes of the reservoir at its initial state. According to pre-exploitation data, it is suggested the Los Humeros reservoir fluids are made of a mixture of meteoric water of very light isotopic composition (paleo-fluids) and andesitic water. The relationship {delta} D vs {delta} 18 O from pre-exploitation data indicates the produced fluids are composed of a mixture of (at least) two fluids with distinct isotopic compositions. At the more enriched end of the mixing relationship are the isotopic compositions of the wells H-23 and H-18 (located in the southern area of the field), while the lighter fluids were found in well H-16 (originally) and then in well H-16 (repaired). It was found that the liquid phases of deep wells are more enriched in {delta} 18 O while the shallow wells present lower values, suggesting a convection process at the initial state. Based on this isotopic profile, it is considered that even the production depths of the wells H-1, H-12 and H-16 (repaired) are just about the same, but their respective isotopic compositions are quite different. The {delta} 18 O value for well H-16 (repaired) seems to be that of condensate steam, while the corresponding values for wells H-1 and H-12 fall within the value interval of the deep wells (H-23). This suggests wells H-1 and H-12 are collecting very deep fluids enriched in {delta} 18 O. These results could be useful in creating a conceptual model of the reservoir. [Spanish] Se analizaron datos isotopicos ({delta}18 O, {delta}D) de los fluidos de pozos productores del campo geotermico de Los Humeros, Pue., para investigar el posible origen de los fluidos asi como los procesos dominantes del yacimiento en su estado inicial. De acuerdo con datos previos a la explotacion, se plantea que los fluidos del yacimiento

Proposal to neutralize acid fluids from wells in the Los Humeros, Pue., geothermal field; Propuesta para la neutralizacion de fluidos acidos provenientes de pozos del campo geotermico de Los Humeros, Pue.

Energy Technology Data Exchange (ETDEWEB)

Flores Armenta, Magaly del Carmen; Ramirez Montes, Miguel; Garcia Cuevas, Juan Manuel [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)]. E-mail: magaly.flores@cfe.gob.mx

2009-07-15

Neutralizing an acidic fluid consists of adding a sodium hydroxide solution to neutralize the H group of acids, therefore increasing the pH. The injection of sodium hydroxide has to be continuous and at a proper depth inside the well to protect against the corrosion of casing and surface equipment. Neutralization is a common practice used in geothermal fields, such as at The Geysers in the US and Miravalles in Costa Rica-places where aggressive fluids cause problems for extracting and using geothermal fluids commercially. A zone surrounding wells H-4, H-16 and H-29 in the northern section of the Los Humeros, Pue., geothermal field, known as the Colapso Central, has shown evidence of aggressively acidic fluids. Several wells drilled in the area had to be repaired, thus plugging and isolating the deepest production zones. Well H-43 was drilled two years ago in the northern zone of the field, and even though it is not located in the aggressive-fluid zone, the well presents mineralogical features possibly indicating the presence of acidic fluids. Therefore, before producing this well it has been proposed we install a neutralization system with general characteristics presented in this paper. The system will prevent corrosion that up to now has prevented exploitation of the deep portion of Colapso Central, helping to develop the field in a more profitable way. [Spanish] Neutralizar un fluido acido consiste en agregarle una solucion de hidroxido de sodio. Esto neutraliza el grupo de acidos H y en consecuencia aumenta el pH. La inyeccion de hidroxido de sodio se realiza de manera continua y a una profundidad adecuada dentro del pozo para proteger a la tuberia y a todo el equipo superficial contra la corrosion. La neutralizacion es una practica comun que se viene realizando en campos como Los Geysers en Estados Unidos y en Miravalles, Costa Rica, donde la presencia de fluidos agresivos causa problemas en la extraccion y aprovechamiento del fluido geotermico con fines

Oxidación en vapor de agua a 700 ºC y 750 ºC del acero inoxidable AISI 317 recubierto con aluminio por CVD-FBR.

OpenAIRE

Jose L. Marulanda; Saul I. Castañeda; Aduljay Remolina

2014-01-01

Se realizó la oxidación del acero inoxidable austenítico AISI 317 recubierto con aluminio por deposición química de vapor en lecho fluidizado, a temperaturas de 700 °C y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de SEM y difracción de rayos X, para observar la morfología de los óxidos. Se realizó la simulación termodinámica del proceso de oxidación en vapor de agua de...

Drilling of bilateral wells: analysis and selection of wells in the Los Humeros, Pue., geothermal field; Perforacion de pozos bilaterales: analisis y seleccion de pozos en el campo geotermico de Los Humeros, Pue.

Energy Technology Data Exchange (ETDEWEB)

Flores Armenta, Magaly del Carmen; Ramirez Montes, Miguel [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)]. E-mail: miguel.ramirez02@cfe.gob.mx

2010-01-15

Drilling bilateral geothermal wells has been conducted successfully in fields in the U.S., the Philippines and Japan, among other places. The reason for drilling a second leg in a well is to increase production by penetrating additional production zones. In this report, criteria are presented for selecting wells in Los Humeros, Pue., geothermal field to be considered for a second leg, taking into account the mechanical condition of the wells, geological targets, distances between wells, production characteristics and thermodynamic conditions. The cases of wells H-3, H-8, H-11, H-16, H-33, H-34 and H-36, which have low production, were reviewed. Wells H-3, H-8 and H-34 were selected as the best subjects for bi-directional drilling. A design is proposed for constructing a second leg in well H-8. [Spanish] La perforacion de pozos bilaterales se ha venido realizando de manera exitosa en campos geotermicos de Estados Unidos, Filipinas y Japon, entre otros. El objetivo de perforar una segunda pierna en un mismo pozo es incrementar su produccion, ya que habran mas zonas de produccion. En este reporte se presentan los criterios para la seleccion de pozos del campo geotermico de Los Humeros, Pue., candidatos para una segunda pierna, considerando el estado mecanico de los mismos, los objetivos geologicos, la distancia entre pozos, sus caracteristicas de produccion y sus condiciones termodinamicas. Para ello se revisaron los casos de los pozos H-3, H-8, H-11, H-16, H-33, H-34 y H-36, que presentan una produccion baja. Posteriormente, aplicando los criterios de evaluacion y con la informacion obtenida de cada pozo, se seleccionaron los pozos H-3, H-8 y H-34 como los que presentan mejores condiciones para la perforacion bidireccional. Finalmente, se establecio un diseno para la construccion de una segunda pierna en el pozo H-8.

Oxidación en vapor de agua del acero inoxidable aisi 317 a 700 y 750ºc

OpenAIRE

MARULANDA AREVALO, JOSE LUDDEY; REMOLINA MILLAN, ADULJAY; BARON, JAIRO ALBERO

2013-01-01

Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

OXIDACIÓN EN VAPOR DE AGUA DEL ACERO INOXIDABLE AISI 317 A 700 Y 750ºC

OpenAIRE

José Luddey Marulanda Arevalo; Aduljay Remolina Millan; Jairo Alberto Barón

2013-01-01

Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

Nuevo equipo de proceso de destilación fraccionada en continuo por arrastre con vapor de aceites esenciales del jugo de limón mexicano

Directory of Open Access Journals (Sweden)

Francisco J. Padilla M.

2007-01-01

Full Text Available En este trabajo se presenta un nuevo equipo llamado Destilador-Fraccionador Horizontal, para realizar el procesos de destilación fraccionada en continuo por arrastre de vapor de aceites esenciales obtenidos a partir del jugo de limón mexicano (Citrus aurantifolia. La capacidad de fraccionación del nuevo equipo es analizada con soluciones modelo y soluciones reales de jugo de limón. Se emplean diseños experimentales y métodos estadísticos para investigar el desempeño del equipo y para validar su capacidad de fraccionar. Mediante la determinación de la relación S/F (gramos de vapor necesario para extraer 1 g de aceite destilado en la fase vapor, se determina que el nuevo equipo requiere una menor cantidad de energía para lograr la separación de los aceites esenciales. Eficiencias de extracción de aceites esenciales superiores al 90% son alcanzadas empleando las soluciones reales de jugo de limón.

Response to exploitation (1982-2002) of the Los Azufres, Michoacan (Mexico) geothermal field. Part II: South Zone; Respuesta a la explotacion (1982-2003) del yacimiento geotermico de Los Azufres, Michoacan (Mexico). Parte II: Zona Sur

Energy Technology Data Exchange (ETDEWEB)

Arellano G, Victor Manuel [Instituto de Investigaciones Electricas, Cuernavaca, Morelos, (Mexico); Torres R, Marco Antonio [Comision Federal de Electricidad, Morelia, Michoacan (Mexico); Barragan R, Rosa Maria [Instituto de Investigaciones Electricas, Cuernavaca, Morelos, (Mexico); Sandoval M, Fernando [Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

2005-06-01

The paper describes the thermodynamic evolution of fluids in the Los Azufres geothermal field's southern zone reservoir, as a response to exploitation from 1982 to 2002. Thermodynamic conditions for the reservoir fluids were estimated with production data using the WELFLO heat-and-flow well simulator. In the southern zone, initial fluid thermodynamic conditions indicated that compressed liquid, two-phase fluids and vapor occurred in the reservoir, depending on the well depths. The fist response to exploitation consisted in a pressure drop an enthalpy increase. For the long term, the following patterns have been identified: pressure and mass flow-rate drop, boiling, cooling, vapor production and in some wells affected by injection an increase in both pressure and mass flow rate. The isotopic results of well fluids in the southern zone showed the occurrence of two processes. The first, with a positive slope, indicates a mixing of reservoir and injection fluids and mainly affects wells Az-2, Az-16, Az-33, Az-36 and Az-46. The second, with a negative slope, results from the original processes of reservoir steam separation and partial condensation. [Spanish] En este trabajo se presenta un estudio sobre la evolucion termodinamica de los fluidos de la zona sur del yacimiento de Los Azufres, como respuesta a la extraccion e inyeccion de fluidos, desde el inicio de su explotacion en 1982 hasta el ano 2002. Las condiciones termodinamicas de los fluidos del yacimiento se estimaron mediante el simulador de flujo de fluidos y calor en pozos WELFLO, a partir de datos de produccion. Las condiciones termodinamicas iniciales de los fluidos de la zona sur, indicaron la existencia de liquido comprimido, dos fases con liquido dominante y dos fases con vapor dominante, dependiendo de la profundidad de los pozos. La respuesta inicial de la zona sur a la explotacion consistio en una disminucion de la presion y un aumento en la entalpia mientras que a mas largo plazo se han observado

Evolución del vapor de agua en la atmósfera mar del sureste español

Directory of Open Access Journals (Sweden)

J. Quereda Sala

2004-01-01

Full Text Available Uno de los mayores retos actuales de la climatología mediterránea es la detección de alguna señal de alerta ante el aumento térmico y disminución de las precipitaciones previstas en la mayor parte de los modelos teóricos de Cambio Climático. El objetivo de nuestro trabajo concierne a un proceso básico escasamente tratado hasta ahora y que bien podría constituir un verdadero talón de Aquiles en la hipótesis sobre el Cambio Climático. Si la elevación regional de las temperaturas es un proceso real, la evaporación en las aguas superficiales del Mediterráneo ha de haber aumentado simultáneamente. ¿Dónde está ese vapor? Una cuestión ciertamente no menor por cuanto ese vapor es el principal gas de efecto invernadero y cuya retroacción sería la responsable de la mayor parte de los aumentos térmicos, tanto de los actuales como de los futuros previstos por los modelos teóricos

Oxidación en vapor de agua a 700 ºC y 750 ºC del acero inoxidable AISI 317 recubierto con aluminio por CVD-FBR.

Directory of Open Access Journals (Sweden)

Jose L. Marulanda

2014-01-01

Full Text Available Se realizó la oxidación del acero inoxidable austenítico AISI 317 recubierto con aluminio por deposición química de vapor en lecho fluidizado, a temperaturas de 700 °C y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de SEM y difracción de rayos X, para observar la morfología de los óxidos. Se realizó la simulación termodinámica del proceso de oxidación en vapor de agua de los substratos para conocer las posibles fases sólidas y gaseosas que se podrían formar, en presencia de una ambiente con 100% vapor de agua y una atmosfera de presión. La forma de ataque a 750 ºC es similar a 700 ºC, aunque la velocidad de oxidación es mayor, ya que la difusión de los elementos de aleación y las reacciones de oxidación son más rápidas. Los recubrimientos de aluminio tienen una buena resistencia a la oxidación en vapor de agua, ya que forman una capa superficial de Al 2 O 3 , que es compacta y adherente, la cual protege al substrato del ataque corrosivo.

Application of ethanol as a geothermal tracer: a field-test in the Los Azufres geothermal field, Michoacan, Mexico

Energy Technology Data Exchange (ETDEWEB)

Tello Hinojosa, Enrique [Comision Federal de Electricidad, Morelia, Michoacan (Mexico); Pal Verma, Mahendra [Comision Federal de Electricidad, Morelia, Michoacan (Mexico); Suarez Arriaga, Mario C. [Universidad Michoacana de San Nicolas de Hidalgo, Morelia, Michoacan (Mexico); Barrera Conzalez, Victor; Sandoval Medina, Fernando [Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

2005-12-01

fluoresceina presentaron una degradacion del 99.4% y del 99.7%, respectivamente, mientras que para el etanol el porcentaje de degradacion en las mismas condiciones fue de solo el 44.6%. Consecuentemente, puede usarse alcohol etilico como un trazador confiable hasta unos 250 grados centigrados, mientras la rodamina y la fluoresceina pueden utilizarse solo a menos de 200 grados centigrados y unicamente donde el tiempo de retorno esperado sea menor de 7 dias. Se empleo etanol como trazador en una prueba de campo en la zona sur el campo geotermico de Los Azufres. La maxima concentracion se detecto en un pozo monitor en la fase de vapor 15 dias despues de la inyeccion, y en la fase liquida o salmuera la maxima se detecto 34 dias despues de la inyeccion. Esto sugiere que el alcohol se fracciona preferentemente en la fase de vapor y que se mueve o migra el doble de rapido que en la fase liquida. La velocidad del trazador puede calcularse en 176 metros por dia en la fase de vapor y en 77.5 metros por dia en la salmuera. El etanol presenta caracteristicas suficientemente buenas para usarse como trazador en las dos fases en ambientes geotermicos.

Evolution of the geothermal system in Acoculco, Pue., Mexico: Study based on petrography of well EAC-2 and other information; Evolucion del sistema geotermico de Acoculco, Pue., Mexico: un estudio con base en estudios petrograficos del pozo EAC-2 y en otras consideraciones

Energy Technology Data Exchange (ETDEWEB)

Viggiano Guerra, Julio Cesar [Universidad Michoacana de San Nicolas de Hidalgo, Michoacan (Mexico)]. E-mail: cesar.viggiano@live.com; Flores Armenta, Magaly; Ramirez Silva, German R. [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)

2011-01-15

yacimientos tipo kaipohan. Dos pozos exploratorios se han perforado en la zona: en 1995 el EAC-1 a 1810 m de profundidad y en 2008 el EAC-2 a 1900 m de profundidad. En este reporte se discuten los resultados e interpretacion de los estudios petrograficos del segundo pero se emplea parte de la informacion del primero para la interpretacion de la evolucion del sistema hidrotermal. De manera sintetica se puede establecer que la zona geotermica de Acoculco se encuentra en su etapa hidrotermal senil dado que se ha verificado, de acuerdo con los estudios de mineralogia hidrotermal y con otras consideraciones, un cambio en el regimen de convectivo hacia convectivo forzado o conductivo. Sobresale el hecho de que el sistema no se ha reciclado, quiza porque las rocas no lo han permitido y, por lo tanto, esta feneciendo. Esto, naturalmente, no ha sido obice para la presencia de un importante volumen de masa caliente (300 grados centigrados) hornfelsica y granitica en el subsuelo que abre un espectro de posibilidades para la explotacion de un sistema geotermico mejorado (EGS, por sus siglas en ingles). Quedaria por investigar la factibilidad del proyecto en el tema de la vulnerabilidad de las rocas de yacimiento (hornfels y granito) para su mejora de permeabilidad por los medios convencionales experimentados en estos proyectos, ya que parece ser que la naturaleza fracaso en ese intento.

Initial temperature distribution in Los Humeros, Mexico, geothermal field; Distribucion de temperatura inicial en el campo geotermico de Los Humeros, Puebla

Energy Technology Data Exchange (ETDEWEB)

Garcia, A; Arellano, V; Aragon, A; Barragan, R.M; Izquierdo, G [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico); Pizano, A [Comision federal de Electricidad, Los Humeros, Puebla (Mexico)

2000-12-01

The initial formation temperatures surrounding 40 wells from the Los Humeros geothermal field are presented. These temperatures were estimated using the Horner and the sphere methods. A brief discussion on the applicability of each method is presented and previous applications are detailed. Then the more likely reservoir temperature of each well versus elevation is plotted based on the estimations about the main feed zone and the temperature of each well. The boiling with depth curve for pure water is also included. Two longitudinal and one traverse geological sections are presented to illustrate the field initial temperature distribution, the lithology and layers thickness, the basement topography and the wells traversed along each sections. Also, the main feed zones of the wells are indicated. Finally, the last series of measured temperature logs in well H-26 are produced by numerical simulation. This considers the well circulation losses and an assumed initial temperature profile. This profile iteratively modified until the computed profiles match the measured temperature profiles. The last assumed temperature profile is then considered as the best approximation to the undisturbed formation temperature around well H-26 and it is then compared with the stabilized temperatures obtained via the Horner and Sphere methods. [Spanish] Se presentan las temperaturas iniciales o estabilizadas de la formacion circundante a 40 pozos del campo geotermico Los Humeros, las cuales se estimaron mediante los metodos de Horner y el metodo de la esfera. Se presenta una discusion sobre la aplicacion de cada metodo y se detallan las aplicaciones previas del metodo de la esfera. Posteriormente y con base en las estimaciones de las principales zonas de aporte de cada pozo y sus correspondientes temperaturas se grafican las temperaturas mas probables de yacimiento para cada pozo contra la elevacion y se incluye en la misma grafica la curva de ebullicion del agua contra la elevacion. Se

Geochemical evidences of the boiling phenomena in Los Humeros geothermal field; Evidencias geoquimicas del fenomeno de ebullicion en el campo de Los Humeros

Energy Technology Data Exchange (ETDEWEB)

Munguia Bracamontes, Fernando; Lopez Mendiola, Juan Manuel [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1990-12-31

The geochemical behavior of the fluids in the geothermal field Los Humeros suggests the existence of a reservoir of relatively low permeability, with hydrostatic pressure gradients and thermodynamic conditions of pressure-temperature close to the boiling point in stationary conditions, that is, non-disturbed. Nevertheless, the fluid geochemistry also indicates the presence of steam under stationary conditions, mainly in the fault, fracture, fissure, etc. zones. The steam diminishes progressively as the extraction time increases, being replaced by boiling fluid. [Espanol] El comportamiento geoquimico de los fluidos en el campo geotermico de Los Humeros sugiere la existencia de un yacimiento de relativa baja permeabilidad, con gradientes de presion hidrostatica y condiciones termodinamicas de presion-temperatura cercanas al punto de ebullicion a condiciones estables; es decir, no perturbadas. Sin embargo, la geoquimica de los fluidos tambien indica la existencia de vapor bajo condiciones estables, principalmente en las zonas de fallas, fracturas, fisuras, etc. El vapor disminuye progresivamente conforme aumenta el tiempo de extraccion, siendo reemplazado por fluido en ebullicion.

Geochemical evidences of the boiling phenomena in Los Humeros geothermal field; Evidencias geoquimicas del fenomeno de ebullicion en el campo de Los Humeros

Energy Technology Data Exchange (ETDEWEB)

Munguia Bracamontes, Fernando; Lopez Mendiola, Juan Manuel [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1989-12-31

The geochemical behavior of the fluids in the geothermal field Los Humeros suggests the existence of a reservoir of relatively low permeability, with hydrostatic pressure gradients and thermodynamic conditions of pressure-temperature close to the boiling point in stationary conditions, that is, non-disturbed. Nevertheless, the fluid geochemistry also indicates the presence of steam under stationary conditions, mainly in the fault, fracture, fissure, etc. zones. The steam diminishes progressively as the extraction time increases, being replaced by boiling fluid. [Espanol] El comportamiento geoquimico de los fluidos en el campo geotermico de Los Humeros sugiere la existencia de un yacimiento de relativa baja permeabilidad, con gradientes de presion hidrostatica y condiciones termodinamicas de presion-temperatura cercanas al punto de ebullicion a condiciones estables; es decir, no perturbadas. Sin embargo, la geoquimica de los fluidos tambien indica la existencia de vapor bajo condiciones estables, principalmente en las zonas de fallas, fracturas, fisuras, etc. El vapor disminuye progresivamente conforme aumenta el tiempo de extraccion, siendo reemplazado por fluido en ebullicion.

Initial Pressure Distribution in the Geothermal Field of Los Humeros, Puebla, Mexico; Distribucion de presion inicial en el campo geotermico de Los Humeros, Puebla, Mexico

Energy Technology Data Exchange (ETDEWEB)

Arellano, Victor M.; Izquierdo, Georgina; Aragon, Alfonso; Barragan, Rosa Maria; Garcia, Alfonso [Instituto de Investigaciones Electricas (Mexico); Pizano, Arturo [Comision Federal de Electricidad (Mexico)

2001-09-01

To obtain the undisturbed distribution of pressures of a field flow, a significant amount of data concerning geological, geochemical, geophysical, and field drilling and engineering aspects, from 42 wells located at the geothermal field of Los Humeros, was analysed. Based on the studied data, models of the field pressure distribution in its initial state were developed. The models reveal the existence of at least two deposits. One of them, the most superficial, is located between 1025 and 1600 meters over the sea level, and from its excellent congruence with the pressure profile of a boiling water column, it may be considered as a predominantly liquid field. The pressure profile of this field is that of a boiling water column, at a temperature of about 300-330 Celsius degrees. The second field is below 850 meters over the sea level and from the known data it reaches at least 100 meters over the sea level. It is considered a low-liquid saturated field. The temperatures of the wells supplied by this field were estimated to be about 300-40 Celsius degrees. [Spanish] Para inferir las distribuciones de presion no perturbadas del fluido del yacimiento, se analizo una considerable cantidad de informacion relacionada con los aspectos geologicos, geoquimicos, geofisicos, de perforacion e ingenieria de yacimientos, correspondiente a 42 pozos del camo geotermico de Los Humeros, Puebla. Sobre la base de los datos analizados se desarrollaron modelos de distribucion de la presion del yacimiento en su estado inicial. Dichos modelos revelan la existencia de, cuando menos, dos yacimientos. El primero y mas superficial se encuentra localizado entre 1,600 y 1,025 metros sobre el nivel del mar (msnm), y dada su excelente concordancia con el perfil de presion correspondiente a una columna de agua en ebullicion, puede afirmarse que se trata de un yacimiento de liquido dominante. El perfil de presion de este yacimiento corresponde a una columna de agua en ebullicion de 300 a 330

Evaluación del cuesco de palma africana y del carbón del cerrejón para producir carbón activado

Directory of Open Access Journals (Sweden)

Anundo Polanía León

2010-05-01

Full Text Available Se produjeron carbones activados a partir de carbón de El Cerrejón y del Cuesco de Palma Africana mediante activación con vapor de agua y KOH, a 700 y 800 ó 900°C variando la relación activante/carbonizado y el tiempo de activación. Los tiempos de activación a los que se desarrolla mayor área superficial son mucho más cortos con el vapor de agua que con el KOH. Al activar con este último se obtienen valores de área superficial similares errlas dos materias primas, según la temperatura de trabajo, mientras que la activación con vapor de agua, presenta características totalmente diferentes. La activación del Cuesco de Palma Africana con KOH, produce carbones esencialmente microporosos, mientras que con vapor de agua, produce carbones activados con una apreciable mesoporosidad favorecida por el incremento de la temperatura. La activación del carbón de El Cerrejón con KOH o vapor de agua produce carbones activados microporosos. En líneas generales se puede decir que el tipo de textura porosa obtenida en la producción de un carbón activado, es función no sólo de los agentes activantes utilizados, sino también del tipo u origen de la materia prima, mientras que la calidad del carbón activado, (área superficial total, es función del tiempo y de la temperatura de activación, al menos con los materiales de partida usados en este trabajo.

Control Robusto de Orden Fraccionario de la Presión del Vapor en el Domo Superior de una Caldera Bagacera

Directory of Open Access Journals (Sweden)

R. Rivas-Perez

2014-01-01

Full Text Available Resumen: En el presente trabajo se desarrolla un controlador de orden fraccionario del tipo IDα-1 para el control robusto de la presión de vapor en el domo superior de una caldera bagacera, el cual posibilita aumentar la efectividad en el control, así como la eficiencia energética de estos equipos. La aplicación de un controlador de orden fraccionario se justifica por el hecho de que la dinámica del proceso objeto de estudio puede cambiar de forma drástica con la variación del calor especifico de combustión (I. Se obtiene un modelo matemático nominal de la variación de la presión de vapor en el domo superior de la caldera bagacera. Los resultados de validación del modelo matemático obtenido muestran un elevado grado de adecuación. Mediante estudios experimentales se estimó el rango de variación de los parámetros dinámicos del modelo matemático obtenido cuando el calor específico de combustión varía en el rango de operación [Imin,-1Imax]. El diseño del controlador IDα se realiza en base a especificaciones en el dominio de la frecuencia. Se muestran los resultados comparativos de simulación del sistema de control desarrollado con controladores IDα-1 vs PI e IDα-1 vs PID, en el sentido de exhibir el mismo comportamiento dinámico en lazo cerrado para las especificaciones de la planta nominal y en presencia de perturbaciones. Estos resultados demuestran que cuando la ganancia de la presión del vapor en el domo superior de la caldera bagacera presenta variaciones en-1el rango [Kmin, Kmax] el controlador IDα diseñado exhibe mejores prestaciones, así como una mayor robustez. Abstract: This paper presents a fractional order controller of the class IDα-1 for robust control of the steam pressure in the steam drum of a bagasse boiler. The proposed controller improves the effectiveness on the control, and likewise the energy efficiency of this plant. The

Presence of cross flow in the Cerro Prieto geothermal field, BC; Presencia de flujo cruzado en el campo geotermico de Cerro Prieto, BC

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Rodriguez, Marco Helio [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Residencia General de Cerro Prieto, Mexicali, Baja California (Mexico)]. E-mail: marco.rodriguez01@cfe.gob.mx

2011-01-15

During the development of Cerro Prieto geothermal field, BC, exploitation has increased gradually, causing a continuous drop in pressure to almost 100 bars in the central and eastern parts of the field. This has occurred despite the high natural recharge induced by the reservoir exploitation and helped by the high permeability of the reservoir and the wide availability of natural recharge of low-temperature water in the vicinity. The strata above the production zones have significantly lower temperatures than these zones, but due to the particular characteristics of the reservoir, do not have pressure drops. As the pressure of producing strata declines, the hydraulic pressure differential between them and the overlying strata increases. Thus in recent years the phenomenon of cross flow occurs with greater frequency and severity. In this paper, this phenomenon is analyzed, detailing the specific mechanisms favoring it and identifying the stage (drilling or workover) in which it commonly occurs. Rigorous supervision during these stages is crucial to identifying cross flow and to taking necessary measures to save the well. Cross flow cases are presented at different stages in the history of a well: during drilling, repair, before and during the stimulation, and during production. [Spanish] Durante el desarrollo del campo geotermico de Cerro Prieto, BC, la explotacion se ha incrementado en forma gradual provocando una continua caida de presion, que en las porciones central y oriente ha sido de casi 100 bars. Esto ha ocurrido a pesar de la enorme recarga natural inducida por la explotacion, favorecida por la alta permeabilidad del yacimiento y la gran disponibilidad de recarga natural de agua de baja temperatura en los alrededores del mismo. Los estratos ubicados encima de las zonas productoras presentan temperaturas significativamente menores que estos, pero debido a las caracteristicas particulares del yacimiento, no han presentado abatimiento en su presion. En la

Seismologic study of Los Humeros geothermal field, Puebla, Mexico. Part II: Seismic tomography by attenuation of coda waves (Qc-1) of local earthquakes; Estudio sismologico del campo geotermico de Los Humeros, Puebla, Mexico. Parte II: Tomografia sismica por atenuacion a partir de ondas de coda (Qc-1) de sismos locales

Energy Technology Data Exchange (ETDEWEB)

Antayhua, Yanet; Lermo, Javier [Instituto de Ingenieria, Universidad Nacional Autonoma de Mexico, D.F (Mexico); Carlos, Vargas [Departamento de Geociencias, Universidad Nacional de Colombia (Colombia)]. E-mail: jles@pumas.iingen.unam.mx

2008-07-15

productores, mientras que los valores altos se observaron en la periferia del campo geotermico. Asimismo, la distribucion de la atenuacion Qc{sup -1} en 3D y 2D muestra que las anomalias de alta atenuacion sismica se ubican en los extremos norte, sur y suroeste de la zona de explotacion actual, y a profundidades mayores a 2.5 km. Palabras clave: Los Humeros, atenuacion intrinseca, ondas de coda, tomografia sismica.

Evaluation of the energy potential, biogenesis and essential characteristics of the geothermal submarine systems in Mexico; Evaluacion del potencial, biogenesis y caracteristicas esenciales de los sistemas geotermicos submarinos en Mexico

Energy Technology Data Exchange (ETDEWEB)

Suarez Arriaga, Mario Cesar [Universidad Michoacana de San Nicolas Hidalgo, Morelia, Michoacan (Mexico)

2004-12-01

profundidad, hasta los recursos geotermicos profundos, a mas de 3000 metros de profundidad. Las fuentes geotermicas no tradicionales incluyen las partes profundas y los limites de los reservorios hidrotermales tradicionales, los sistemas en roca seca o humeda caliente, los yacimientos geopresurizados del Golfo de Mexico y los sistemas submarinos hidrotermales observados principalmente en la costa norte mexicana del Oceano Pacifico. La energia geotermica submarina surge por la existencia de rupturas profundas en el fondo marino, a lo largo de los centros de dispersion oceanicos entre las placas tectonicas. Estos sistemas tienen una longitud total aproximada de 65,000 Km. en la corteza oceanica. Hay dos tipos basicos de sistemas marinos existentes en el Golfo de California: los recursos profundos, localizados a lo largo de las cordilleras entre las placas de la corteza oceanica a mas de 2000 m bajo el nivel del mar, y los recursos poco profundos cerca de las plataformas continentales, entre 20 y 50 metros de profundidad. El calor submarino poco profundo tambien se relaciona con fallas y fracturas en el fondo del mar cerca de algunas costas. Este subsistema se encuentra tambien en la costa de Punta Banda en Ensenada, Baja California. El potencial preliminar de la energia contenida en tales reservorios se estima, en promedio, en 1120 MWt por cada km3 de roca submarina. Las caracteristicas quimicas especificas de las aguas hidrotermales encontradas en esos sistemas oceanicos indican que las interacciones agua-roca, ocurren bajo condiciones de presion y temperatura altas. La energia geotermica submarina soporta ricas variedades de comunidades biologicas a profundidades donde las plantas no tienen acceso a la luz solar para realizar la fotosintesis. Hay indicios de que las posibles condiciones para la sintesis de sustancias y elementos quimicos necesaria para el origen de la vida primitiva, pudieron ser los sistemas hidrotermales submarinos.

Application of SPCALC for chemical and thermodynamic speciation of fluids -example for wells LV-4A, LV-11 and LV-13, Las Tres Virgenes geothermal field, BCS; Aplicacion del SPCALC en la especiacion quimica y termodinamica de fluidos: ejemplo del caso de los pozos LV-4A, LV-11 y LV-13, del campo geotermico de Las Tres Virgenes, BCS

Energy Technology Data Exchange (ETDEWEB)

Viggiano Guerra, J.C.; Sandoval Medina, F.; Flores Armenta, M.C. [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)]. E-mail: fernando.sandoval@cfe.gob.mx, E-mail: magaly.flores@cfe.gob.mx; Perez, R.J. [Universidad de Calgary (Canada); Gonzalez Partida, E. [Universidad Nacional Autonoma de Mexico, Centro de Geociencias, Mexico, D.F. (Mexico)

2009-01-15

+ CO{sub 2}) if boiling occurs or is induced, for instance, by flashing. Reactions occurring during the process produce the rest of the observed minerals in rocks (illite+quartz{+-}epidote), although the balance diagrams do not truly represent the process due to the just-mentioned explanation. On the other hand the oversaturated phases, according to SPCALC, are mainly silica varieties (from quartz to chalcedony), a prediction that is confirmed by the silica scaling occurring at superficial installations. Calcite, on the contrary, is reported as unsaturated, an apparent contradiction with reality, which shows problematic calcite scaling produced during the well exploitation according to the same just-mentioned mechanism. It is therefore recommended to adjust the SPCALC calculations at the reservoir level to be able to prevent imminent calcite scaling. Chemical and multi-phase speciation by using SPCALC results are useful and practical, if results are interpreted carefully. [Spanish] El SPCALC es un excelente software recientemente adquirido por la Comision Federal de Electricidad (CFE) a traves de un contrato con la Universidad Nacional Autonoma de Mexico (UNAM) y la universidad de Calgary, Canada, mediante el cual se obtiene la especiacion quimica y multifasica de fluidos geotermicos. La metodologia consiste en el calculo de variables termodinamicas, tales como las actividades (a) y las fugacidades (f) de las especies quimicas, asi como los indices de saturacion (log Q/K) de las fases minerales del yacimiento, lo que implica que modela condiciones termodinamicas de yacimiento (pH entre otras cosas) contribuyendo asi a pronosticar incrustaciones y corrosion dado que tambien simula la tasa de corrosion de los fluidos. En este articulo se modelan fluidos que han percolado a traves de rocas granodioriticas cretacicas de los pozos LV-4A, LV-11 y LV-13 del campo geotermico de Las Tres Virgenes, BCS, haciendo uso del software mencionado a partir de sus analisis quimicos. Asi

A new method of damage determination in geothermal wells from geothermal inflow with application to Los Humeros, Mexico

Energy Technology Data Exchange (ETDEWEB)

Aragon, A [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Moya, S. L [Centro Nacional de Investigacion y Desarrollo Tecnologico, Cuernavaca, Morelos (Mexico); Garcia-Gutierrez, A; Arellano, V [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2008-10-15

Geothermal inflow type curves were obtained for different values of well damage (i.e., inflow performance relationships). The method was evaluated by diagnosing the damage of thirteen producing wells in the Los Humeros, Puebla, Mexico geothermal field. Permeability determinations were carried out for these wells and their productivity indices were estimated. Comparison of the diagnoses made via damage effects against the results of field pressure tests showed that the maximum difference between both approaches is on the order of 0.7 damage units. The methodology allows reservoir characterization along its productive life, since several production tests are carried out while the reservoir is producing. The data obtained from production tests are used to determine the damage effect and permeability of the rock formation. Previously the damage (skin factor) could only be determined from the analyses of transient pressure tests. [Spanish] Se presenta la obtencion de curvas-tipo de influjo geotermico para diferentes valores de dano, y se demuestra su aplicacion en los analisis de produccion de pozos geotermicos determinando el dano en trece pozos del campo geotermico de Los Humeros, Puebla, Mexico. Tambien se hicieron determinaciones de la permeabilidad en las zonas de produccion de estos pozos y de sus respectivos indices de productividad. Se compararon los resultados del valor de dano obtenido con la metodologia propuesta, con los valores de dano obtenidos a partir de pruebas de presion, encontrando que las diferencias maximas entre ambas tecnicas es del orden de 0.7 unidades de dano. La presente metodologia permite la caracterizacion del yacimiento a lo largo de su vida productiva a partir de las mediciones de las pruebas de produccion efectuadas en los pozos. La metodologia propuesta es innovadora porque anteriormente el dano solamente se podia determinar a partir de los analisis de las mediciones de la pruebas de presion.

Modelización del perfil de soldadura y de la cavidad de vapor en la aleación de aluminio 5182 soldada con láser

Directory of Open Access Journals (Sweden)

Pastor, M.

2001-12-01

Full Text Available The purpose of this research is the study of the laser welding process of the aluminum alloy 5182 and the development of models by means of the COSMOS/M package, in order to predict the shape of the keyhole and the temperatures profile of the weld. Modeling has been done considering the degree of defocusing. The heat flow applied on the models was a Gauss flow, considering the condition of the focused face and the conditions of negative and positive defocusing. The validity of the models has been demonstrated comparing their results with those obtained by experimental tests. The extent of defocusing of laser beam affected the stability of the keyhole and welding geometry.

El presente trabajo se introduce en el desarrollo de modelos para predecir la forma de la cavidad de vapor y el perfil de la aleación de aluminio 5182 con soldadura láser. Para el procesamiento del modelo se ha empleado el paquete profesional de Elementos Finitos COSMOS/M. La modelización de la soldadura se realizó considerando como variable el grado de desenfoque del haz de láser y la distribución del flujo de calor según un modelo Gaussiano, para las condiciones de haz enfocado y de desenfoque negativo y positivo. La validez de los resultados obtenidos se comprobó mediante la comparación con los resultados obtenidos en pruebas experimentales, concluyéndose que el grado de desenfoque del haz del láser afecta notablemente la estabilidad de la cavidad de vapor y la geometría de la soldadura.

La tecnología del vapor aplicada en las Minas de Almadén. Desde su origen hasta el Consejo de Administración

OpenAIRE

Calderón Herrera, David

2017-01-01

La desaparición de un gran número de elementos importantes del patrimonio industrial está siendo compensada en los últimos años con el incremento de la labor investigadora tradicional combinada con el uso de las técnicas de reconstrucción virtual, lo que le ha dado un nuevo impulso a la recuperación y puesta en valor de éste patrimonio acercándolo con ello a la sociedad. En este trabajo de investigación se estudia la etapa de instalación de la tecnología del vapor en las minas de Almadén (Ciu...

Chemical and isotopic characteristics of rainwater at Los Humeros geothermal field, Puebla, Mexico and surrounding areas; Caracteristicas quimicas e isotopicas del agua de lluvia en el campo geotermico de Los Humeros, Puebla, Mexico y zonas aledanas

Energy Technology Data Exchange (ETDEWEB)

Tovar Aguado, Rigoberto; Cruz Grajales, Irma [Comision Federal de Electricidad, Los Humeros, Puebla (Mexico)

2000-12-01

A study of chemical and isotopic characteristics of rainwater at Los Humeros geothermal field was undertaken for the second consecutive year. Samples were collected in seven stations-two inside the field and five on the periphery. In 1996, a total of 99 samples were collected and 104 were collected in 1997. Of these, 19-18.26% of the total-had a negative alkalinity. The Atempan (No.5) and Campamento (No.1) stations showed the highest number of anomalous samples (31.25 and 27.8%, respectively). Anomalous samples in Perote station were not observed a result that we attribute to the predominant wind direction. The results for the Campamento station are attributed to the thermal inversion phenomena occurring when the samples with negative alkalinity were obtained. Concentrations of cations in some samples were relatively high, with the maximum concentration of calcium in the Los Humeros station (79.7 ppm) . Other significantly high values were found in the Texcal station (34.8 ppm) and Perote (33.8 ppm) due to the presence of dust particles scattered in the air and because of the lack of pavement where the sampling stations are located. Another factor affecting these figures could be the presence of block and lime factories in the neighborhood. Although measured concentrations may seem high, reports exist with similar concentrations in nongeothermal areas. Oxygen-18 and deuterium contents were determined for each stations, mixing anomalous samples. The results show that the most enriched samples correspond to the San Juan Xiutetelco, Puebla (No. 6) station and the minimum to the Perote Veracruz (No. 7) station. The concentration of SO{sub 4} has marine and industrial origins, with a contribution of the first source ranging between 10 and 25 percent. [Spanish] En el campo geotermico de Los Humeros, Puebla se realizo, por segundo ano consecutivo, la caracterizacion quimica e isotopica de agua de lluvia en muestras colectadas en siete estaciones, dos localizadas dentro

The use of residual geothermal energy in an edible mushroom production plant, Los Humeros geothermal fields (Mexico): Achievements and alternatives; El uso de la energia geotermica residual en la planta productora de hongos comestibles del campo geotermico Los Humeros (Mexico): Logros y alternativas

Energy Technology Data Exchange (ETDEWEB)

Rangel Rangel, Maria Elena [Proteccion ambiental, Puebla (Mexico)

2000-12-01

A plant for raising edible mushrooms with residual geothermal energy is a project of the Comision Federal de Electricidad (CFE). The results reflect important achievements in the development of technology for the productions of wholesome and available food with geothermal heat instead of conventional energy sources. The installations have an enormous technological and commercial potential- demonstrated by the cultivation of oyster mushrooms (Pleurotus ostreatus), which success has awakened the interest of research institutions. The Instituto of Ecologia, A.C., has begun a joint project with CFE cultivating shiitake mushrooms (Lentinula edodes) with geothermal energy. These achievements mark a clear trend toward the integral use of facilities, the establishment of a crop with greater economic advantages, and the diffusion of this project. [Spanish] La planta productora de hongos comestibles es un proyecto de la Comision Federal de Electricidad (CFE) para dar un uso alterno a la energia geotermica residual. Los resultados obtenidos hasta el momento reflejan logros importantes en la generacion de tecnologia propia para la produccion de un alimento sano y accesible, sustituyendo la energia proveniente de combustibles convencionales por calor geotermico. Las instalaciones creadas cuentan con un enorme potencial tecnologico y comercial demostrando con el cultivo de las setas (Pleurotus ostreatus) con un exito tal que ha despertado el interes de instituciones dedicadas a la investigacion. Tal es el caso de Instituto de Ecologia, A.C que acualmente se encuentra involucrado en un proyecto conjunto sobre el cultivo del hongo Lentinula edodes (shiitake) utilizando energia geotermica en su proceso productivo. Con lo anterior, se esta marcando una clara tendencia hacia el aprovechamiento integral de las instalaciones, el establecimiento de un cultivo con mayores ventajas economicas y la difusion de este proyecto.

Comparison of molecular models of carbon monoxide for calculation of vapor-liquid equilibrium

Directory of Open Access Journals (Sweden)

Bibian Alonso Hoyos-Madrigal

2015-01-01

Full Text Available Existen varios modelos moleculares para el monóxido de carbono desarrollados a partir de diferentes mediciones experimentales. El objetivo de este trabajo es comparar los resultados que varios de estos modelos producen en el cálculo del equilibrio líquido-vapor en busca de recomendar qué modelo debe ser usado de acuerdo la propiedad y la fase que se desea calcular. Los modelos seleccionados corresponden a cuatro modelos no polares, con uno o dos sitios Lennard-Jones, y cuatro modelos polares, con dipolos o cargas parciales para representar la polaridad del monóxido de carbono. Simulaciones Monte Carlo en la versión Gibbs canónica (NVT-GEMC se emplearon para determinar las densidades de las fases en equilibrio, la presión de vapor y la entalpia de vaporización entre 80 y 130 K con cada uno de los modelos seleccionados. Se encontró que los modelos más complejos SVH, ANC y PGB, son los que mejor describen la densidad del líquido saturado (alrededor de 7% de desviación promedio, pero estos modelos generan desviaciones mayores al 40% para las propiedades del vapor y al 20% para la entalpia de vaporización. Por otro lado, el modelo no- polar BLF generó las menores desviaciones para la presión de saturación y la densidad del vapor (6.8 y 21.5%, respectivamente. Este modelo, al igual que el modelo HCB, produce desviaciones aceptables para la densidad del líquido y la entalpia de vaporización (entre 10 y 12%. Los modelos no polares BLF y HCB, que no requieren el cálculo de las interacciones de largo alcance, se pueden considerar como los modelos moleculares que presentan un balance satisfactorio entre desviaciones en los resultados y complejidad de cálculo.

Summary of a Gas Transport Tracer Test in the Deep Cerros Del Rio Basalts, Mesita del Buey, Los Alamos NM.

Energy Technology Data Exchange (ETDEWEB)

Stauffer, Philip H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rahn, Thomas A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ortiz, John Philip [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Salazar, Larry Joseph [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boukhalfa, Hakim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Snyder, Emily Elisabeth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-16

Here we describe results from a tracer test in the Cerros del Rio basalt beneath Mesita del Buey, Technical Area 54 (TA-54) at Los Alamos National Laboratory (LANL or the Laboratory). This report follows from plans outlined in our previous Tracer Test Work Plan (LANL 2016). These activities were conducted by LANL to further characterize subsurface properties of the Cerros del Rio basalts at Material Disposal Area (MDA) L (Figure 1.1-1). The work presented follows from the “Interim Measures Work Plan for Soil-Vapor Extraction of Volatile Organic Compounds from Material Disposal Area L, Technical Area 54, Revision 1,” submitted to the New Mexico Environment Department (NMED) in September 2014 (LANL 2014). Remediation of the MDA L vapor plume by soil-vapor extraction (SVE) is recommended as part of the final remedy in the “Corrective Measures Evaluation Report for Material Disposal Area L, Solid Waste Management Unit 54-006, at Technical Area 54, Revision 2” to meet a remedial action objective of preventing groundwater from being impacted above a regulatory standard by the transport of volatile organic compounds (VOCs) to groundwater through soil vapor (LANL 2011).

Caracterización del tipo de cavitación mediante dinámica computacional de fluidos para posteriores aplicaciones al estudio experimental del daño por cavitación

OpenAIRE

Moll, Flavio; Manuele, Diego; Coussirat Núñez, Miguel Gustavo; Guardo Zabaleta, Alfredo de Jesús; Fontanals García, Alfred

2011-01-01

La cavitación se corresponde a una estructura bifásica (líquido-vapor) cuando la presión del líquido disminuye hasta su presión de vapor, pv. Esta disminución de pv puede deberse a diversos factores relacionados con la hidrodinámica del flujo y las propiedades físicas del fluido, pudiendo presentar diferentes características. En la cavitación hidrodinámica, pueden distinguirse efectos que pueden producir un acoplamiento fluido-estructura (lock-in) que puede favorecen la falla del material, só...

Environmental framework for the development of the Los Humeros, Puebla geothermal field; Contexto ambiental del desarrollo del campo geotermico de Los Humeros, Puebla

Energy Technology Data Exchange (ETDEWEB)

Pastrana Melchor, Eugenio J.; Fernandez Solorzano, Maria Elena; Mendoza Rangel, Ernesto; Hernandez Ayala, Cuauhtemoc [Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

2005-06-01

The construction, operation and maintenance of the Los Humeros, Puebla, geothermal field were undertaken in accordance with Mexican environmental regulations. The resolutions on environmental impacts, license for atmospheric pollution prevention, concession title for exploitation and use of national waters, permission for wastewater discharging services, company registration for producing dangerous wastes and fulfillment of all conditions noted in the documents show the applicable environmental laws for the project have been followed. [Spanish] La construccion, operacion y mantenimiento del campo geotermoelectrico Los Humeros, Puebla, se ha llevado a cabo dentro del marco juridico ambiental vigente en Mexico. Las resoluciones en materia de impacto ambiental, la licencia en materia de prevencion de la contaminacion de la atmosfera, el titulo de concesion para explorar, usar o aprovechar aguas nacionales, el permiso para descargar aguas residuales domesticas, el registro como empresa generadora de residuos peligrosos, y el cumplimiento de las disposiciones y condicionantes establecidos en cada uno de estos documentos, evidencian la observancia de la legislacion ambiental aplicable al proyecto.

Mobile vapor recovery and vapor scavenging unit

International Nuclear Information System (INIS)

Stokes, C.A.; Steppe, D.E.

1991-01-01

This patent describes a mobile anti- pollution apparatus, for the recovery of hydrocarbon emissions. It comprises a mobile platform upon which is mounted a vapor recovery unit for recovering vapors including light hydrocarbons, the vapor recovery unit having an inlet and an outlet end, the inlet end adapted for coupling to an external source of hydrocarbon vapor emissions to recover a portion of the vapors including light hydrocarbons emitted therefrom, and the outlet end adapted for connection to a means for conveying unrecovered vapors to a vapor scavenging unit, the vapor scavenging unit comprising an internal combustion engine adapted for utilizing light hydrocarbon in the unrecovered vapors exiting from the vapor recovery unit as supplemental fuel

Basic aspects of the Cerro Prieto reservoir water recharge; Aspectos basicos de la recarga de agua al reservorio de Cerro Prieto

Energy Technology Data Exchange (ETDEWEB)

Mercado, Sergio [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1991-12-31

The Cerro Prieto geothermal field, located 30 km South of Mexicali City, Baja California, has at present an installed capacity of 620 MW in geothermal power plants, that operating with endogenous steam, make use of the underground energy by means of deep wells, from which about 80 million cubic meters per year of high enthalpy water and steam mixture are extracted. During the exploitation physical an chemical changes in the hydrothermal fluids discharged by the wells have been detected, which shows, among other things, an elevated water recharge, located towards the West area of the field and a low recharge in the part of the east zone area. For this reason the hot brine waste re-injection is recommended, (previously treated to eliminate the silica excess) to thermally an hydraulically recharge the reservoir in that part of the field. [Espanol] El campo geotermico de Cerro Prieto, situado a 30 km al sur de la ciudad de Mexicali, Baja California, cuenta actualmente, despues de 18 anos en explotacion, con 620 MW de capacidad instalada en plantas geotermoelectricas que, operando con vapor endogeno, aprovechan la energia del subsuelo mediante pozos profundos de los que se extraen alrededor de 80 millones de metros cubicos por ano de una mezcla de agua vapor de elevada entalpia. Durante la explotacion se han percibido cambios fisicos y quimicos en los fluidos hidrotermales descargados por los pozos, lo que indica, entre otras cosas, una recarga elevada de agua localizada hacia el poniente del campo y una recarga baja en una zona de la parte oriental. Por ello se recomienda la reinyeccion de salmuera geotermica caliente de desecho (previamente tratada para eliminar el exceso de silice) para recargar termica e hidraulicamente el reservorio en esa parte del campo.

Basic aspects of the Cerro Prieto reservoir water recharge; Aspectos basicos de la recarga de agua al reservorio de Cerro Prieto

Energy Technology Data Exchange (ETDEWEB)

Mercado, Sergio [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1992-12-31

The Cerro Prieto geothermal field, located 30 km South of Mexicali City, Baja California, has at present an installed capacity of 620 MW in geothermal power plants, that operating with endogenous steam, make use of the underground energy by means of deep wells, from which about 80 million cubic meters per year of high enthalpy water and steam mixture are extracted. During the exploitation physical an chemical changes in the hydrothermal fluids discharged by the wells have been detected, which shows, among other things, an elevated water recharge, located towards the West area of the field and a low recharge in the part of the east zone area. For this reason the hot brine waste re-injection is recommended, (previously treated to eliminate the silica excess) to thermally an hydraulically recharge the reservoir in that part of the field. [Espanol] El campo geotermico de Cerro Prieto, situado a 30 km al sur de la ciudad de Mexicali, Baja California, cuenta actualmente, despues de 18 anos en explotacion, con 620 MW de capacidad instalada en plantas geotermoelectricas que, operando con vapor endogeno, aprovechan la energia del subsuelo mediante pozos profundos de los que se extraen alrededor de 80 millones de metros cubicos por ano de una mezcla de agua vapor de elevada entalpia. Durante la explotacion se han percibido cambios fisicos y quimicos en los fluidos hidrotermales descargados por los pozos, lo que indica, entre otras cosas, una recarga elevada de agua localizada hacia el poniente del campo y una recarga baja en una zona de la parte oriental. Por ello se recomienda la reinyeccion de salmuera geotermica caliente de desecho (previamente tratada para eliminar el exceso de silice) para recargar termica e hidraulicamente el reservorio en esa parte del campo.

Effect of the blades and seals system wear on steam turbine efficiency and power; Efecto del desgaste del sistema de alabes y sellos sobre la eficiencia y potencia de las turbinas de vapor

Energy Technology Data Exchange (ETDEWEB)

Campos Amezcua, Alfonso; Kubiak Szyszka, Janusz [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1997-12-31

The implementation of a method for steam turbine evaluation through the measured geometry in the flow channel and its operating conditions, is presented. This method, previously developed, allows the identification and quantification of the power and efficiency loss due to the wear of its elements (worn or bent blades, worn seals, deposits, etc.); the benefit that is obtained is a more precise knowledge on the turbine behavior and a basis is acquired to give priority to the maintenance work, from the stand point of energy utilization. In this paper, the power and efficiency loss of a 300 MW steam turbine is located and evaluated, a sensibility analysis is presented for the typical elements that cause the deterioration of the efficiency in this type of turbines. [Espanol] Se presenta la implementacion de un metodo de evaluacion de turbinas de vapor a partir de la geometria medida del canal de flujo y sus condiciones de operacion. Este metodo, previamente desarrollado, permite identificar y cuantificar las perdidas de potencia y eficiencia debido al desgaste de sus elementos (alabes desgastados o doblados, sellos desgastados, depositos, etcetera); el beneficio que se obtiene es un conocimiento mas preciso del comportamiento de la turbina y que se tiene una base para dar prioridad a los trabajos de mantenimiento desde el punto de vista de aprovechamiento de la energia. En este articulo se localizan y evaluan las perdidas de potencia y eficiencia de una turbina de vapor de 300 MW, ademas, se presenta un analisis de sensibilidad para los elementos tipicos que originan el deterioro de la eficiencia en este tipo de turbinas.

Effect of the blades and seals system wear on steam turbine efficiency and power; Efecto del desgaste del sistema de alabes y sellos sobre la eficiencia y potencia de las turbinas de vapor

Energy Technology Data Exchange (ETDEWEB)

Campos Amezcua, Alfonso; Kubiak Szyszka, Janusz [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1998-12-31

The implementation of a method for steam turbine evaluation through the measured geometry in the flow channel and its operating conditions, is presented. This method, previously developed, allows the identification and quantification of the power and efficiency loss due to the wear of its elements (worn or bent blades, worn seals, deposits, etc.); the benefit that is obtained is a more precise knowledge on the turbine behavior and a basis is acquired to give priority to the maintenance work, from the stand point of energy utilization. In this paper, the power and efficiency loss of a 300 MW steam turbine is located and evaluated, a sensibility analysis is presented for the typical elements that cause the deterioration of the efficiency in this type of turbines. [Espanol] Se presenta la implementacion de un metodo de evaluacion de turbinas de vapor a partir de la geometria medida del canal de flujo y sus condiciones de operacion. Este metodo, previamente desarrollado, permite identificar y cuantificar las perdidas de potencia y eficiencia debido al desgaste de sus elementos (alabes desgastados o doblados, sellos desgastados, depositos, etcetera); el beneficio que se obtiene es un conocimiento mas preciso del comportamiento de la turbina y que se tiene una base para dar prioridad a los trabajos de mantenimiento desde el punto de vista de aprovechamiento de la energia. En este articulo se localizan y evaluan las perdidas de potencia y eficiencia de una turbina de vapor de 300 MW, ademas, se presenta un analisis de sensibilidad para los elementos tipicos que originan el deterioro de la eficiencia en este tipo de turbinas.

System of aid for the starting of the steam generator of a thermoelectric unit; Sistema de ayuda para el arranque del generador de vapor de una unidad termoelectrica

Energy Technology Data Exchange (ETDEWEB)

Quintero R, Agustin; Suarez C, Dionisio A; Aquino E, Juan C; Diaz H, Carlos A; Cruz T, Jorge A; Sanchez L, Jose A [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2002-07-01

This article presents the development of an on line aid system, whose objective is to aid the operator of a thermoelectric unit, providing the information that is required to carry out the heating and pressurization of the steam generator in the shortest possible time. The former takes place respecting the operation limits determined by the manufacturer and the conditions of security established to carry out the maneuvers of operation of the equipment. The system incorporates a scheme of predictive control, based on a neuronal model that estimates the optimal position of two final elements of control to fulfill with the curves of reference for the temperature and pressure of the main steam. The system is based on an architecture client-server and uses technology Web for the access of the information through a navigator of the Internet. [Spanish] Este articulo presenta el desarrollo de un sistema de ayuda en linea, cuyo objetivo es asistir al operador de una unidad termoelectrica, proporcionando la informacion que requiere para llevar a cabo el calentamiento y presurizacion del generador de vapor en el menor tiempo posible. Lo anterior se efectua respetando los limites de operacion determinados por el fabricante y las condiciones de seguridad establecidas para efectuar las maniobras de operacion de los equipos. El sistema incorpora un esquema de control predictivo, basado en un modelo neuronal, que estima la posicion optima de dos elementos finales de control para cumplir con las curvas de referencia para la temperatura y presion del vapor principal. El sistema esta basado en una arquitectura cliente-servidor y utiliza tecnologia Web para el acceso a la informacion a traves de un navegador del Internet.

Vapor pressures and enthalpies of vaporization of azides

International Nuclear Information System (INIS)

Verevkin, Sergey P.; Emel'yanenko, Vladimir N.; Algarra, Manuel; Manuel Lopez-Romero, J.; Aguiar, Fabio; Enrique Rodriguez-Borges, J.; Esteves da Silva, Joaquim C.G.

2011-01-01

Highlights: → We prepared and measured vapor pressures and vaporization enthalpies of 7 azides. → We examined consistency of new and available in the literature data. → Data for geminal azides and azido-alkanes selected for thermochemical calculations. - Abstract: Vapor pressures of some azides have been determined by the transpiration method. The molar enthalpies of vaporization Δ l g H m of these compounds were derived from the temperature dependencies of vapor pressures. The measured data sets were successfully checked for internal consistency by comparison with vaporization enthalpies of similarly structured compounds.

Geochemistry and isotopic characterization of rain in the zones of Los Azufres, Michoacan and Los Humeros, Puebla and its relation with geothermal fluids; Caracterizacion geoquimica e isotopica de lluvia en las zonas de Los Azufres, Michoacan y Los Humeros, Puebla y su relacion con fluidos geotermicos

Energy Technology Data Exchange (ETDEWEB)

Verma, Mahendra P; Santoyo, Socrates; Aragon, Alfonso [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico); Fernandez, Ma. Elena [Comision Federal de Electricidad Morelia, Michoacan (Mexico); Tovar, Rigoberto [Comision Federal de Electricidad, Los Azufres (Mexico); Casimiro, Emigdio; Sandoval, Fernando [Comision Federal de Electricidad, Los Humeros, Puebla (Mexico); Johnson, Craig [USGS, Denver, Colorado, (United States); Gerardo-Abaya, Jane [IAEA, Viena (Austria)

1999-12-01

, whereas there is less then 10% sea spray sulfate at Los Azufres. The {delta}{sup 3}4S values of H{sub 2}S of geothermal fluid are very similar to those of rainwater. A compilation of {delta}{sup 3}4S values for different sources of sulfur emissions indicates that it is practically impossible to define the origin of sulfur in rainwater, but the combined results of chemical and isotopic monitoring suggest that the geothermal emissions have no contribution to rainwater acidity. [Spanish] Se presentan los resultados preliminares obtenidos del estudio de monitoreo quimico e isotopico de las precipitaciones pluviales en los campos geotermicos de Los Humeros, Los Azufres y sus zonas de referencia durante el periodo de lluvia 1995-1998. Se recolectaron las muestras de lluvia en siete de los sitios de Los Humeros y ocho de Los Azufres. Los valores de la alcalinidad resultaron positivos para casi todas las muestras de lluvia en Los Humeros, lo que indica que en esta zona no existe acidez. Algunos valores de alcalinidad en los sitios Vivero y Guadalajara de Los Azufres fueron negativos, aunque muy pequenos, por lo que se concluye que existe poca acidez en la lluvia en Los Azufres. En el caso de Los Humeros se encontro buena correlacion entre la alcalinidad y la concentracion de calcio, lo que sugiere que las muestras puedan estar afectadas probablemente por el polvo de la zona. La concentracion de aniones, Cl{sup -}, SO{sub 4} y NO{sub 3} es baja en ambos campos y con una tendencia bien definida. La concentracion de NO{sub 3} y SO{sub 4} en las lluvias de Los Azufres disminuye con el avance de la temporada. En el caso de Los Humeros casi no existe NO{sub 3} y SO{sub 4} en las lluvias de Los Azufres disminuye con el avance de la temporada. En el caso de Los Humeros casi no existe NO{sub 3}. Como referencia cabe senalar que los valores de NO{sub 3} en las lluvias de la ciudad de Mexico son superiores a 10 ppm e indican una relacion con la contaminacion industrial. Esto sugiere que el

Simulation and analysis of the tangential flow in the combustion chamber of a steam generator; Simulacion y analisis del flujo tangencial en la camara de combustion de un generador de vapor

Energy Technology Data Exchange (ETDEWEB)

Hernandez Ramirez, Isaias

1997-06-01

supplying ducts, were obtained, with a maximum discrepancy of 5.5 m/s between the data published by McKenty and Gravel (1997) and this analysis, for the case of combustion gases in the interior of the furnace. Temperature profiles were obtained, which were overestimated in the order of 417 Celsius degrees for the case of the temperature of gases in the center of the combustion chamber, when comparing them with the corresponding ones obtained by McKenty and Gravel (1997). It is speculated that this discrepancy must to be due to the omission of the connection of the radiation model to the global computational model and; the contours of concentration of species for the combustion products in the chamber were considered (carbon dioxide, oxygen and nitrogen), obtaining only the qualitative behavior of these. It is proposed as conclusion that the computational model developed in this thesis work can be used for the estimation of flow of fluids patterns, heat transference and transference of mass of a steam generator VU-60 of the tangential type and similar to the one taken as a base for this analysis. One improvement to the computational model developed could be achieved including the radiation effect, which requires a larger memory capacity of the computer hardware than the one available during the elaboration of this thesis. [Espanol] El presente trabajo de tesis describe la simulacion y analisis de la camara de combustion de un generador de vapor VU-60 del tipo tangencial, el cual esta basado en la solucion de la ecuacion generalizada de transporte, empleando modelos matematicos desarrollados para la caracterizacion de fenomenos fisicos para cerrar los sistemas de ecuaciones gobernantes. Para la solucion de los modelos matematicos y ecuaciones gobernantes se empleo el metodo de volumen finito, el cual se basa en el concepto de volumen de control. Se desarrollo un modelo computacional tridimensional por medio del cual se estimaron los perfiles de velocidad, presion, temperatura

Determinación experimental del equilibrio líquido-vapor del sistema etanol-agua-glicerina

OpenAIRE

Chasoy Rojas, William Andrés

2012-01-01

Actualmente, la obtención de alcohol anhidro se lleva a cabo mediante el uso de tecnologías como tamices moleculares, destilación extractiva con etilenglicol y destilación azeotrópica; esta última reemplazada casi totalmente por su alto consumo energético en relación a las otras y por la toxicidad del solvente que se utiliza en el proceso. Siendo la destilación extractiva una alternativa para la obtención del alcohol anhidro que puede competir con la tecnología de tamices molec...

Nuevos diseños de sistemas de control híbrido, genético-adaptativo, para la regulación de la eficiencia del bloque termoenergético de las empresas del níquel.

Directory of Open Access Journals (Sweden)

Antonio Muñoz

2006-10-01

Full Text Available El artículo muestra los resultados de la investigación del sistema de avanzado híbrido (genéticoadaptativo para la generación de vapor, a través de lazos de regulación para la reducción de la dispersión de las variables del régimen operacional del proceso, con la aplicación de nuevas estrategias de control óptimo con algoritmos genéticos del gasto de energía, sobre la desviación del régimen de trabajo de las calderas; todo lo cual contribuye a la reducción de las pérdidas de energía para generar vapor, permitiendo implementar sistemas control híbridos, resultantes de la integración de sistemas de control genético-adaptativos.

Virtual test bench as a complement to study thermal area: application in vapor compression systems

Directory of Open Access Journals (Sweden)

Juan Manuel Belman-Flores

2015-01-01

Full Text Available Este artículo describe un simulador educativo desarrollado en el software Engineering Equation Solver para representar el comportamiento de un sistema de compresión de vapor. La aplicación está enfocada con propósitos educativos, particularmente para que estudiantes de ingeniería adquieran habilidades en el manejo de instalaciones de refrigeración. Mediante el uso de este simulador, los estudiantes tendrán la capacidad de analizar fácilmente la infl uencia que tienen parámetros medidos experimentalmente (como la velocidad de rotación del compresor, el fl ujo volumétrico y la temperatura de fl uidos secundarios sobre la efi ciencia energética del sistema y sus componentes principales. El banco virtual consta de una pantalla principal que muestra un esquema general del sistema de compresión de vapor con parámetros de entrada y de salida. Desde la pantalla principal, el desempeño de los componentes principales puede ser analizado. Finalmente, este banco de pruebas virtual ha sido probado por estudiantes de ingeniería, concluyendo que el simulador es una herramienta de apoyo que permite mejorar el aprendizaje de las diferentes áreas del conocimiento.

Analysis and control of erosion by solid particles in the elements of the flow system of steam turbines; Analisis y control de erosion por particulas solidas en los elementos del sistema de flujo de turbinas de vapor

Energy Technology Data Exchange (ETDEWEB)

Mazur Czerwiec, Zdzislaw; Campos Amezcua, Alfonso; Campos Amezcua, Rafael [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2010-07-01

The analysis of erosion by solid particles is presented of different elements of the flow channel of the steam turbines that operate in Mexico: nozzles, stop valves, blade bosses, labyrinth seals and rotor disc; using tools of of Computational Fluid Dynamics (CFD). In these main elements of turbines a strong problem of erosion was registered that threatens the reliable operation of the turbines, its availability and its optimal yield. With base on the results of the numerical analyses, the design modifications of the different elements were developed from the flow channel of the steam turbines, in order to reduce the erosion and thus diminishing the energy losses and increasing the steam turbine efficiency. This work presents the main benefits that the Thermoelectric Power Plants obtain with the reduction of the erosion by solid particles that affect the critical components of steam turbines: extension of the period between maintenance, replacement of components, reduction of operation and maintenance costs of the turbines, and extension of the useful life of the main components. [Spanish] Se presenta el analisis de erosion por particulas solidas de diferentes elementos del canal de flujo de las turbinas de vapor que operan en Mexico: toberas, valvula de paro, tetones de los alabes, sellos de laberinto y disco del rotor; utilizando herramientas de Dinamica de Fluidos Computacional (DFC). En estos elementos principales de turbinas se registro un fuerte problema de erosion que amenaza la operacion confiable de las turbinas, su disponibilidad y su rendimiento optimo. Con base en los resultados de los analisis numericos, se desarrollaron las modificaciones de diseno de los diferentes elementos del canal de flujo de las turbinas de vapor, con el proposito de reducir la erosion y asi, disminuir las perdidas de energia e incrementar el rendimiento de las turbinas de vapor. Este trabajo presenta los principales beneficios que obtienen las Centrales Termoelectricas con la

Vapor pressure and enthalpy of vaporization of aliphatic propanediamines

International Nuclear Information System (INIS)

Verevkin, Sergey P.; Chernyak, Yury

2012-01-01

Highlights: ► We measured vapor pressure of four aliphatic 1,3-diamines. ► Vaporization enthalpies at 298 K were derived. ► We examined consistency of new and available data in the literature. ► A group-contribution method for prediction was developed. - Abstract: Vapor pressures of four aliphatic propanediamines including N-methyl-1,3-propanediamine (MPDA), N,N-dimethyl-1,3-propanediamine (DMPDA), N,N-diethyl-1,3-propanediamine (DEPDA) and N,N,N′,N′-tetramethyl-1,3-propanediamine (4MPDA) were measured using the transpiration method. The vapor pressures developed in this work and reported in the literature were used to derive molar enthalpy of vaporization values at the reference temperature 298.15 K. An internal consistency check of the enthalpy of vaporization was performed for the aliphatic propanediamines studied in this work. A group-contribution method was developed for the validation and prediction vaporization enthalpies of amines and diamines.

Evaluación agroindustrial de los aceites esenciales de Artemisia dracunculos L, Franseria artemisioides Willd, Salvia officinalis L, Lippia dulcis Frev, y Occimun americanum L en condiciones del Valle del Cauca

OpenAIRE

Luis F Saldarriaga C; Ginna M Sánchez M; Carmen Rosa Bonilla Correa; Manuel Salvador Sánchez Orozco; Harlen Gerardo Torres Castañeda

2010-01-01

En parcelas establecidas de la Colección de Trabajo de Plantas Medicinales del Centro Experimental CEUNP en condiciones del departamento del Valle del Cauca, se tomaron muestras del material vegetal mediante el corte manual en un marco de 0.25m² ; se separaron hojas, tallos y flores de cada especie. Se determinó el porcentaje de materia seca y se acondicionó para el proceso de extracción de aceite esencial mediante arrastre con vapor. A los aceites obtenidos se...

Vapor pressure and enthalpy of vaporization of linear aliphatic alkanediamines

International Nuclear Information System (INIS)

Pozdeev, Vasiliy A.; Verevkin, Sergey P.

2011-01-01

Highlights: → We measured vapor pressure of diamines H 2 N-(CH 2 ) n -NH 2 with n = 3 to 12. → Vaporization enthalpies at 298 K were derived. → We examined consistency of new and available in the literature data. → Enthalpies of vaporization show linear dependence on numbers n. → Enthalpies of vaporization correlate linearly with Kovat's indices. - Abstract: Vapor pressures and the molar enthalpies of vaporization of the linear aliphatic alkanediamines H 2 N-(CH 2 ) n -NH 2 with n = (3 to 12) have been determined using the transpiration method. A linear correlation of enthalpies of vaporization (at T = 298.15 K) of the alkanediamines with the number n and with the Kovat's indices has been found, proving the internal consistency of the measured data.

An application of neural network in geophysical prospecting. Electrical resistivity at Las Virgenes geothermal field, Baja California Sur, Mexico; Una aplicacion de las redes neuronales a la prospeccion geofisica. Resistividad electrica en las Tres Virgenes, Baja California Sur, Mexico

Energy Technology Data Exchange (ETDEWEB)

Palma Guzman, Sergio Hugo [Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

2000-12-01

The technology of the neural network is presented with geophysical focus in the Las Virgenes geothermal field, Baja California Sur, Mexico. The results obtained when extrapolating the associative data of the prospecting magnetoteluria and Vertical Electric Sounding, on the area of the geothermal wells to the rest of the area, allows to classify zones of interest for the geothermal exploitation. Also, the use of these associative parameters with the information of the stabilized temperature of the wells, they allow to predict temperatures for the rest of the area. [Spanish] Se presenta una aplicacion de la tecnologia de las redes neuronales con enfoque geofisico en el campo geotermico de Las Virgenes, Baja California Sur, Mexico. Los resultados obtenidos al extrapolar los datos asociativos de las prospecciones geoelectricas de magnetoteluria y sondeos electricos verticales, en la zona de los pozos geotermicos al resto del area, permiten clasificar zonas de interes para la explotacion geotermica. Tambien, la utilizacion de estos parametros asociativos con la informacion de la temperatura estabilizada de los pozos, permiten predecir temperaturas para la misma area.

Evaluación agroindustrial de los aceites esenciales de Artemisia dracunculos L, Franseria artemisioides Willd, Salvia officinalis L, Lippia dulcis Frev, y Occimun americanum L en condiciones del Valle del Cauca

OpenAIRE

Saldarriaga C, Luis F; Sánchez M, Ginna M; Bonilla Correa, Carmen Rosa; Sánchez Orozco, Manuel Salvador; Torres Castañeda, Harlen Gerardo

2010-01-01

En parcelas establecidas de la Colección de Trabajo de Plantas Medicinales del Centro Experimental CEUNP en condiciones del departamento del Valle del Cauca, se tomaron muestras del material vegetal mediante el corte manual en un marco de 0.25m² ; se separaron hojas, tallos y flores de cada especie. Se determinó el porcentaje de materia seca y se acondicionó para el proceso de extracción de aceite esencial mediante arrastre con vapor. A los aceites obtenidos se les midió la densidad, y el índ...

Evaluación agroindustrial de los aceites esenciales de artemisia dracunculos l, franseria artemisioides willd, salvia officinalis l, lippia dulcis frev, y occimun americanum l en condiciones del valle del cauca

OpenAIRE

Saldarriaga C, Luis F.; Sánchez M, Ginna M.; Bonilla Correa, Carmen Rosa; Sánchez Orozco, Manuel Salvador; Torres Castañeda, Harlen Gerardo

2010-01-01

En parcelas establecidas de la Colección de Trabajo de Plantas Medicinales del Centro Experimental CEUNP en condiciones del departamento del Valle del Cauca, se tomaron muestras del material vegetal mediante el corte manual en un marco de 0.25m2 ; se separaron hojas, tallos y flores de cada especie. Se determinó el porcentaje de materia seca y se acondicionó para el proceso de extracción de aceite esencial mediante arrastre con vapor. A los aceites obtenidos se les midió la densidad, y el índ...

VAPOR PRESSURES AND HEATS OF VAPORIZATION OF PRIMARY COAL TARS

Energy Technology Data Exchange (ETDEWEB)

Eric M. Suuberg; Vahur Oja

1997-07-01

This project had as its main focus the determination of vapor pressures of coal pyrolysis tars. It involved performing measurements of these vapor pressures and from them, developing vapor pressure correlations suitable for use in advanced pyrolysis models (those models which explicitly account for mass transport limitations). This report is divided into five main chapters. Each chapter is a relatively stand-alone section. Chapter A reviews the general nature of coal tars and gives a summary of existing vapor pressure correlations for coal tars and model compounds. Chapter B summarizes the main experimental approaches for coal tar preparation and characterization which have been used throughout the project. Chapter C is concerned with the selection of the model compounds for coal pyrolysis tars and reviews the data available to us on the vapor pressures of high boiling point aromatic compounds. This chapter also deals with the question of identifying factors that govern the vapor pressures of coal tar model materials and their mixtures. Chapter D covers the vapor pressures and heats of vaporization of primary cellulose tars. Chapter E discusses the results of the main focus of this study. In summary, this work provides improved understanding of the volatility of coal and cellulose pyrolysis tars. It has resulted in new experimentally verified vapor pressure correlations for use in pyrolysis models. Further research on this topic should aim at developing general vapor pressure correlations for all coal tars, based on their molecular weight together with certain specific chemical characteristics i.e. hydroxyl group content.

Palinology and stratigraphic sequences of the well ELS-1, Laguna Salada, B.C., Mexico; Palinologia y secuencias estratigraficas del pozo ELS-1, Laguna Salada, B.C., Mexico

Energy Technology Data Exchange (ETDEWEB)

Helenes Escamilla, Javier [CICESE, Ensenada, B.C. (Mexico)

1999-04-01

Palinological analysis of 16 samples from the well ELS-1 in Laguna Salada, allows recognition of environmental changes in the drilled section. No age assignments are made because of the low diversity of the palinological assemblages recovered. These assemblages include species with ages from Campanian to Pleistocene. The cretaceous forms indicate reworking from a cretaceous unit within the Colorado river drainage basin. Integration of the palinological, lithological and well log data permit the recognition of three main cycles. The lower one is regressive and contains mostly fluvial to deltaic shallow marine sediments. The intermediate cycle is transgressive-regressive, contains the maximum flooding surface of the section studied and represents an interval of strong tectonic movements with well developed marine transgressions. The upper cycle is also transgressive-regressive, with lagoon and distal alluvial fan deposits. [Spanish] El analisis palinologico de 16 muestras del pozo: ELS-1 del proyecto geotermico de Laguna Salada permite reconocer cambios ambientales en la seccion perforada. La baja diversidad de los conjuntos palinologicos recuperados impide determinar edades. Se observan especies indicadoras de edades desde Campaniese hasta Pleistoceno. Las formas cretacicas indican retrabajo de alguna unidad cretacica dentro de la cuenca del rio Colorado. La integracion de datos palinologicos, litologicos y de registros geofisicos, permite reconocer tres ciclos principales. El ciclo inferior es regresivo y contiene principalmente sedimentos fluviales a deltaicos de niveles bajos del mar. El ciclo intermedio, es transgresivo-regresivo, contiene la superficie de inundacion maxima de toda la seccion estudiada y representa una etapa de movimientos tectonicos fuertes con transgresiones marinas bien desarrolladas. El ciclo superior tambien es transgresivo-regresivo, con depositos lagunares y de abanicos aluviales distales.

Enthalpy of Vaporization and Vapor Pressures: An Inexpensive Apparatus

Science.gov (United States)

Battino, Rubin; Dolson, David A.; Hall, Michael A.; Letcher, Trevor M.

2007-01-01

A simple and inexpensive method to determine the enthalpy of vaporization of liquids by measuring vapor pressure as a function of temperature is described. The vapor pressures measured with the stopcock cell were higher than the literature values and those measured with the sidearm rubber septum cell were both higher and lower than literature…

Vapor pressures and vaporization enthalpy of codlemone by correlation gas chromatography

International Nuclear Information System (INIS)

Schultz, Shannon M.; Harris, Harold H.; Chickos, James S.

2015-01-01

Highlights: • The vaporization enthalpy of codlemone has been evaluated. • The vapor pressure of codlemone has been evaluated from T = (298.15 to T b ) K. • Vapor pressures for the 1-alkanols standards are available from T = (298.15 to 500) K. - Abstract: The vapor pressure and vaporization enthalpy of codlemone (trans, trans 8,10-dodecadien-1-ol), the female sex hormone of the codling moth is evaluated by correlation gas chromatography using a series of saturated primary alcohols as standards. A vaporization enthalpy of (92.3 ± 2.6) kJ · mol −1 and a vapor pressure, p/Pa = (0.083 ± 0.012) were evaluated at T = 298.15 K. An equation for the evaluation of vapor pressure from ambient temperature to boiling has been derived by correlation for codlemone. The calculated boiling temperature of T B = 389 K at p = 267 Pa is within the temperature range reported in the literature. A normal boiling temperature of T B = (549.1 ± 0.1) K is also estimated by extrapolation

Petroleum Vapor Intrusion

Science.gov (United States)

One type of vapor intrusion is PVI, in which vapors from petroleum hydrocarbons such as gasoline, diesel, or jet fuel enter a building. Intrusion of contaminant vapors into indoor spaces is of concern.

Evaluación preliminar. Tratamiento del mercurio de fluorescentes y bombillas del alumbrado público

Directory of Open Access Journals (Sweden)

Juan Carlos Salas-Jiménez

2015-12-01

Full Text Available La actividad que se estudia es un proceso para inertizar el mercurio de las luminarias (desechos de bombillos y fluorescentes. Este consiste en triturar y mezclar los desechos con azufre aplicando calentamiento para formar un polímero de sulfuro de mercurio, que resulta un producto sólido, inerte, estable y de baja lixiviación que se puede depositar en un relleno sanitario. El calentamiento causa la generación de vapores de azufre molestos y de olor desagradable, por lo que se realizó un cambio del método de tratamiento sin calentar, mediante el uso de una mezcla del desecho de luminaria con azufre y mortero (cemento y arena. Las pruebas de laboratorio preliminares presentan resultados positivos para efectuar pruebas a nivel de planta piloto con este nuevo método a temperatura ambiente. Este proyecto se desarrolló en una de las actividades productivas del Centro de Investigación en Protección Ambiental (CIPA del Tecnológico de Costa Rica.

Análisis comparativo del mantenimiento para locomotoras diesel y de vapor // Comparative analysis of the Maintenance for Diesel and Steam Locomotives.

Directory of Open Access Journals (Sweden)

C. M. Rodríguez Gil

2000-03-01

Full Text Available El mundo globalizado no afecta por igual a todos los países del orbe. En las circunstancias actuales que tiene el ferrocarrilde la primera industria de la República de Cuba: ausencia de piezas de repuesto y limitaciones de recursos de combustible,surge la necesidad de estudiar nuevas fuentes motrices o potenciar la utilización de locomotoras a vapor, introducidas en elpaís desde 1837.La decisión de incrementar la participación de las locomotoras a vapor depende de múltiples factores quedeben ser analizados individualmente e integrados posteriormente en un análisis sistémico. Dentro de estos factores seencuentra, jugando un papel fundamental, el mantenimiento técnico y sus costos. El trabajo tiene como objetivo central elestudio comparativo de los costos por mantenimiento entre parques similares de locomotoras con tracción diesel y devapor. Este estudio forma parte de un proyecto nacional conocido como “Prometeo” encaminado a estudiar la factibilidadde la utilización masiva de las locomotoras a vapor en la industria azucarera. Para realizar el estudio se trabajó en varioscomplejos agro-industriales durante tres zafras azucareras, permitiendo llegar a recomendaciones.Palabras claves: Mantenimiento, locomotoras, costos._____________________________________________________________________________AbstractThe globalized world doesn't affect equally to all the countries. In the current circumstances the railroad of the first industry ofCuba, that is: lack of spare parts limitations of fuel, arises the necessity of the study of new motion sources or to analyze the useof steam locomotives, introduced in the country since 1837.The decision of increasing the participation of these machinesdepends on multiple factors that should be analyzed individually and later integrated in a systemic analysis. The technicalmaintenance and their costs are playing a main paper The work have as objective a comparative study of costs for maintenancebetween

Methodology for energy diagnosis in distribution steam lines; Metodologia para diagnostico de energia en lineas de distribucion de vapor

Energy Technology Data Exchange (ETDEWEB)

Almanza, M; Ambriz, J J; Romero P, H [Universidad Autonoma Metropolitana Iztapalapa, Mexico, D. F. (Mexico)

1993-12-31

This paper shows a methodology that results of great advantage in the development of the energy analysis of an industrial facility that utilizes steam as a mean of energy transport and where the steam operated equipment is physically located in a remote place, away from the generation site. Mention is made here of the equipment characteristics that can be used for such purpose, the most important parameters to identify in a rapid and efficient way the faults presented in the steam distribution system in the industrial plants and the formats that contribute to keep the corresponding records for efficiently maintain in operation the steam pipeline net in conjunction with the involved accessories. [Espanol] En el presenta trabajo se muestra una metodologia que resulta de gran utilidad en el desarrollo del analisis energetico de una planta industrial, en la cual se emplee el vapor como medio de transporte de la energia y en donde el equipo que utiliza el vapor se encuentre fisicamente en un lugar apartado de la zona de generacion. Aqui se mencionan las caracteristicas del equipo que se puede utilizar para dicho diagnostico, los parametros de mayor importancia para identificar en forma rapida y eficiente las fallas que se presentan en el sistema de distribucion de vapor en las plantas industriales y los formatos que contribuyen a llevar los registros correspondientes para mantener operando eficientemente la red de vapor, en conjunto con los accesorios que en ella se involucran.

Methodology for energy diagnosis in distribution steam lines; Metodologia para diagnostico de energia en lineas de distribucion de vapor

Energy Technology Data Exchange (ETDEWEB)

Almanza, M.; Ambriz, J. J.; Romero P, H. [Universidad Autonoma Metropolitana Iztapalapa, Mexico, D. F. (Mexico)

1992-12-31

This paper shows a methodology that results of great advantage in the development of the energy analysis of an industrial facility that utilizes steam as a mean of energy transport and where the steam operated equipment is physically located in a remote place, away from the generation site. Mention is made here of the equipment characteristics that can be used for such purpose, the most important parameters to identify in a rapid and efficient way the faults presented in the steam distribution system in the industrial plants and the formats that contribute to keep the corresponding records for efficiently maintain in operation the steam pipeline net in conjunction with the involved accessories. [Espanol] En el presenta trabajo se muestra una metodologia que resulta de gran utilidad en el desarrollo del analisis energetico de una planta industrial, en la cual se emplee el vapor como medio de transporte de la energia y en donde el equipo que utiliza el vapor se encuentre fisicamente en un lugar apartado de la zona de generacion. Aqui se mencionan las caracteristicas del equipo que se puede utilizar para dicho diagnostico, los parametros de mayor importancia para identificar en forma rapida y eficiente las fallas que se presentan en el sistema de distribucion de vapor en las plantas industriales y los formatos que contribuyen a llevar los registros correspondientes para mantener operando eficientemente la red de vapor, en conjunto con los accesorios que en ella se involucran.

Software for the design of acoustical steam silencers of the reaction-absorption type; Software para el diseno de silenciadores acusticos de vapor del tipo reaccion-absorcion

Energy Technology Data Exchange (ETDEWEB)

Buendia Dominguez, Eduardo H; Alvarez Chavez, Jose M [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1990-12-31

This paper describes the computer program named SILRA, that determines the outline dimensions of an acoustic steam silencer of the reaction-absorption type. These silencers are employed in the geothermoelectric power plants to lower the high levels of pressure and sound caused by the steam discharge to the surrounding atmosphere. The program has the capacity of predicting the noise level generated by the discharge without silencer depending on the emitting source. On SIRLA was successfully coupled the theory described in specialized literature with optimization techniques and experiences acquired in former designs. SIRLA is a powerful tool that allows the designer to optimize the equipment as well as the design time. [Espanol] En este trabajo se describe el programa de computo SILRA, que determina las dimensiones generales de un silenciador acustico de vapor tipo reaccion-absorcion, estos silenciadores se emplean en las centrales geotermoelectricas para abatir los altos niveles de presion de sonido provocados por la descarga del vapor a la atmosfera. El programa tiene la capacidad de predecir el nivel de ruido que genera la descarga sin silenciador, dependiendo de la fuente emisora. En SILRA se acoplaron con exito la teoria descrita en la literatura especializada con tecnicas de optimacion y experiencias adquiridas en disenos anteriores. SILRA es una poderosa herramienta que permite al disenador optimar tanto el equipo como el tiempo de diseno.

Software for the design of acoustical steam silencers of the reaction-absorption type; Software para el diseno de silenciadores acusticos de vapor del tipo reaccion-absorcion

Energy Technology Data Exchange (ETDEWEB)

Buendia Dominguez, Eduardo H.; Alvarez Chavez, Jose M. [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1989-12-31

This paper describes the computer program named SILRA, that determines the outline dimensions of an acoustic steam silencer of the reaction-absorption type. These silencers are employed in the geothermoelectric power plants to lower the high levels of pressure and sound caused by the steam discharge to the surrounding atmosphere. The program has the capacity of predicting the noise level generated by the discharge without silencer depending on the emitting source. On SIRLA was successfully coupled the theory described in specialized literature with optimization techniques and experiences acquired in former designs. SIRLA is a powerful tool that allows the designer to optimize the equipment as well as the design time. [Espanol] En este trabajo se describe el programa de computo SILRA, que determina las dimensiones generales de un silenciador acustico de vapor tipo reaccion-absorcion, estos silenciadores se emplean en las centrales geotermoelectricas para abatir los altos niveles de presion de sonido provocados por la descarga del vapor a la atmosfera. El programa tiene la capacidad de predecir el nivel de ruido que genera la descarga sin silenciador, dependiendo de la fuente emisora. En SILRA se acoplaron con exito la teoria descrita en la literatura especializada con tecnicas de optimacion y experiencias adquiridas en disenos anteriores. SILRA es una poderosa herramienta que permite al disenador optimar tanto el equipo como el tiempo de diseno.

Point of net vapor generation and vapor void fraction in subcooled boiling

International Nuclear Information System (INIS)

Saha, P.; Zuber, N.

1974-01-01

An analysis is presented directed at predicting the point of net vapor generation and vapor void fraction in subcooled boiling. It is shown that the point of net vapor generation depends upon local conditions--thermal and fluid dynamic. Thus, at low mass flow rates the net vapor generation is determined by thermal conditions, whereas at high mass flow rates the phenomenon is hydrodynamically controlled. Simple criteria are derived which can be used to predict these local conditions for net vapor generation. These criteria are used to determine the vapor void fraction is subcooled boiling. Comparison between the results predicted by this analysis and experimental data presently available shows good agreement for wide range of operating conditions, fluids and geometries. (U.S.)

The vapor pressure and enthalpy of vaporization of M-xylene

International Nuclear Information System (INIS)

Rothenberg, S.J.; Seiler, F.A.; Bechtold, W.E.; Eidson, A.F.

1988-01-01

We measured the vapor pressure of m-xylene over the temperature range 273 to 293 deg K with a single-sided capacitance manometer. The enthalpy of vaporization was 42.2 ± 0.1 (SE) kj/ g·mol. Combining our own data with previously published data, we recommend using the values 42.0, 40.6, and 39.1 (± 0.1) (SE) kjg·mol for the enthalpy of vaporization of m-xylene at 300, 340, and 380 deg. K, respectively, and a value for the change in heat capacity on vaporization (ΔCpdeg.) of 35 ± 3 (SE) J/g·mol·K over the temperature range studied. (author)

Anestesia cuantitativa: influencia del tamaño corporal en la eficacia de un nuevo dispositivo para la administración de anestésicos halogenados en circuitos cerrados

OpenAIRE

Otero, Pablo E.

2016-01-01

Los métodos tradicionales de vaporización de líquidos anestésicos volátiles están compuestos por vaporizadores que se ubican fuera del circuito anestésico y movilizan el vapor impulsado por una columna de gas diluyente, generalmente el oxígeno. La casi totalidad de las máquinas anestésicas emplean este método de vaporización conocido como VOC (por sus siglas en inglés, Vaporizer Outside the Circuit). Cuando se emplea un vaporizador ubicado fuera del circuito, el volumen de vapor anestésico in...

The vapor pressure and enthalpy of vaporization of M-xylene

Energy Technology Data Exchange (ETDEWEB)

Rothenberg, S J; Seiler, F A; Bechtold, W E; Eidson, A F

1988-12-01

We measured the vapor pressure of m-xylene over the temperature range 273 to 293 deg K with a single-sided capacitance manometer. The enthalpy of vaporization was 42.2 {+-} 0.1 (SE) kj/ g{center_dot}mol. Combining our own data with previously published data, we recommend using the values 42.0, 40.6, and 39.1 ({+-} 0.1) (SE) kjg{center_dot}mol for the enthalpy of vaporization of m-xylene at 300, 340, and 380 deg. K, respectively, and a value for the change in heat capacity on vaporization ({delta}Cpdeg.) of 35 {+-} 3 (SE) J/g{center_dot}mol{center_dot}K over the temperature range studied. (author)

Enthalpy of vaporization and vapor pressure of whiskey lactone and menthalactone by correlation gas chromatography

International Nuclear Information System (INIS)

Simmons, Daniel; Chickos, James

2017-01-01

Highlights: • The vapor pressure and vaporization enthalpies of cis and trans-whiskey lactone have been evaluated. • Enthalpies of vaporization and vapor pressures of (+)-isomintlactone and (−)-mintlactone were also evaluated. • The sublimation enthalpy and corresponding vapor pressure of (+) -isomintlactone at T = 298.15 K is estimated. - Abstract: Enthalpies of vaporization at T = 298.15 K of cis and trans-whiskey lactone have been evaluated by correlation gas chromatography to be (68.4 ± 1.7) kJ·mol −1 and (67.5 ± 1.7) kJ·mol −1 , respectively. The enthalpies of vaporization of isomintlactone and mintlactone also evaluated by correlation gas chromatography have been found to have vaporization enthalpies of (74.2 ± 1.8) kJ·mol −1 and (73.2 ± 1.8) kJ·mol −1 respectively. The vapor pressures for cis and trans-whiskey lactone at T = 298.15 K have been evaluated as (1.5 ± 0.09) Pa and (2.0 ± 0.1) Pa using vapor pressures of a series of lactones as standards. Vapor pressures for isomintlactone and mintlactone were evaluated as (0.26 ± 0.012) Pa and (0.33 ± 0.02) Pa, respectively. Fusion and sublimation enthalpies for (+)-isomintlactone as well as the vapor pressure of the solid have been estimated.

Oxidación en vapor de agua del acero inoxidable AISI 316 recubierto con Al-Si por deposición química de vapor en lecho fluidizado

Directory of Open Access Journals (Sweden)

José Luddey Marulanda Arevalo

2014-06-01

Full Text Available Stainless steel AISI 316 was coated with aluminum-silicon by Chemical Vapor Deposition in Fluidized Bed Reactor (CVD-FBR to 540°C and subsequently heat treated to improve its mechanical properties and its behavior against oxidation, by inter diffusion of the alloying elements. Later, oxidation was performed austenitic stainless steel aluminum-silicon coated at temperatures of 700 and 750°C, in an environment with 100% steam, to evaluate their performance. Mass gain graphs were made and oxide films were analyzed by SEM and X-ray diffraction to observe the morphology of the oxides. Thermodynamic simulation was carried out during oxidation in water vapor of the substrates for possible solid phases which could be formed. The form of attack at 750°C is similar to 700°C, although the rate of oxidation is increased, because the diffusion of the alloying elements and the oxidation reactions are faster. These coatings have good resistance to oxidation in water vapor and forming an alumina surface layer which protects the substrate from corrosion attack.

Simulación del depósito de Escarcha en superficies frías Simulation of Frost Deposit in Cold Surfaces

OpenAIRE

Jorge A Gatica; Vicente A Pita; Nisio de C Lobo

2009-01-01

Se presenta un código computacional que simula la formación y crecimiento de escarcha sobre una placa mantenida a baja temperatura, por ablimación del vapor de agua de una corriente de aire húmedo que fluye sobre ella. La modelación se basa en ecuaciones de conservación de masa, energía, cantidad de movimiento y especies aplicadas a la escarcha, mezcla aire-vapor e interfase aire-escarcha. El sistema de ecuaciones resulta no lineal acoplado por la fracción volumétrica del hielo, que es calcul...

Experiences of marijuana-vaporizer users.

Science.gov (United States)

Malouff, John M; Rooke, Sally E; Copeland, Jan

2014-01-01

Using a marijuana vaporizer may have potential harm-reduction advantages on smoking marijuana, in that the user does not inhale smoke. Little research has been published on use of vaporizers. In the first study of individuals using a vaporizer on their own initiative, 96 adults anonymously answered questions about their experiences with a vaporizer and their use of marijuana with tobacco. Users identified 4 advantages to using a vaporizer over smoking marijuana: perceived health benefits, better taste, no smoke smell, and more effect from the same amount of marijuana. Users identified 2 disadvantages: inconvenience of setup and cleaning and the time it takes to get the device operating for each use. Only 2 individuals combined tobacco in the vaporizer mix, whereas 15 combined tobacco with marijuana when they smoked marijuana. Almost all participants intended to continue using a vaporizer. Vaporizers seem to have appeal to marijuana users, who perceive them as having harm-reduction and other benefits. Vaporizers are worthy of experimental research evaluating health-related effects of using them.

An inexpensive and stable LED Sun photometer for measuring the water vapor column over South Texas from 1990 to 2001

Science.gov (United States)

Mims, Forrest M.

2002-07-01

A Sun photometer that uses near-infrared light-emitting diodes (LEDs) as spectrally-selective photodetectors has measured total column water vapor in South Texas since February 1990. The 12 years of solar noon observations to date are correlated with upper air soundings at Del Rio, Texas (r2 = 0.75), and highly correlated with measurements by a Microtops II filter Sun photometer (r2 = 0.94). LEDs are inexpensive and have far better long term stability than the interference filters in conventional Sun photometers. The LED Sun photometer therefore provides an inexpensive, stable and portable means for measuring column water vapor.

Waste Tank Vapor Project: Tank vapor database development

International Nuclear Information System (INIS)

Seesing, P.R.; Birn, M.B.; Manke, K.L.

1994-09-01

The objective of the Tank Vapor Database (TVD) Development task in FY 1994 was to create a database to store, retrieve, and analyze data collected from the vapor phase of Hanford waste tanks. The data needed to be accessible over the Hanford Local Area Network to users at both Westinghouse Hanford Company (WHC) and Pacific Northwest Laboratory (PNL). The data were restricted to results published in cleared reports from the laboratories analyzing vapor samples. Emphasis was placed on ease of access and flexibility of data formatting and reporting mechanisms. Because of time and budget constraints, a Rapid Application Development strategy was adopted by the database development team. An extensive data modeling exercise was conducted to determine the scope of information contained in the database. a A SUN Sparcstation 1000 was procured as the database file server. A multi-user relational database management system, Sybase reg-sign, was chosen to provide the basic data storage and retrieval capabilities. Two packages were chosen for the user interface to the database: DataPrism reg-sign and Business Objects trademark. A prototype database was constructed to provide the Waste Tank Vapor Project's Toxicology task with summarized and detailed information presented at Vapor Conference 4 by WHC, PNL, Oak Ridge National Laboratory, and Oregon Graduate Institute. The prototype was used to develop a list of reported compounds, and the range of values for compounds reported by the analytical laboratories using different sample containers and analysis methodologies. The prototype allowed a panel of toxicology experts to identify carcinogens and compounds whose concentrations were within the reach of regulatory limits. The database and user documentation was made available for general access in September 1994

The vapor pressures of explosives

Energy Technology Data Exchange (ETDEWEB)

Ewing, Robert G.; Waltman, Melanie J.; Atkinson, David A.; Grate, Jay W.; Hotchkiss, Peter

2013-01-05

The vapor pressures of many explosive compounds are extremely low and thus determining accurate values proves difficult. Many researchers, using a variety of methods, have measured and reported the vapor pressures of explosives compounds at single temperatures, or as a function of temperature using vapor pressure equations. There are large variations in reported vapor pressures for many of these compounds, and some errors exist within individual papers. This article provides a review of explosive vapor pressures and describes the methods used to determine them. We have compiled primary vapor pressure relationships traceable to the original citations and include the temperature ranges for which they have been determined. Corrected values are reported as needed and described in the text. In addition, after critically examining the available data, we calculate and tabulate vapor pressures at 25 °C.

Evaluación de la generación de vapor de la fábrica de refrescos 23 de Agosto, en Camagüey

Directory of Open Access Journals (Sweden)

Amaury Pérez-Sánchez

2017-05-01

Full Text Available El presente trabajo se llevó a cabo en la fábrica de refrescos 23 de Agosto, con el fin de evaluar la eficiencia energética del generador de vapor, determinar las pérdidas de calor en las tuberías de vapor que se encuentran sin aislamiento, determinar el impacto medioambiental que producen los gases de combustión generados, evaluar el sistema de tratamiento del agua con que se alimenta la caldera (suavizador de agua, así como efectuar un análisis técnico-económico de dos variantes de mejoras, consistentes en 1 precalentamiento del agua con que se alimenta la caldera hasta los 90 C, y 2 aislamiento de las tuberías de vapor con el aislante lana mineral. El empleo del aislante lana mineral redujo las pérdidas de calor en las tuberías en un 90 %, aproximadamente. La eficiencia energética del generador de vapor fue de 86.64 %. Se requiere invertir $ 523.66 pesos cubanos (PC para adquirir e instalar las cantidades necesarias del aislante lana mineral, que se recuperará al cabo de 122 días. El suavizador opera de forma eficiente y los gases contaminantes alcanzan la máxima concentración a los 87.285 m, estando por encima del valor establecido en las normas cubanas. La aplicación de las dos variantes de mejora propuestas trajo consigo un ahorro total anual de PC 9931.92 por el combustible dejado de consumir en el generador de vapor. Se emplearon programas y herramientas computacionales tales como el Contamín, y hojas de cálculo Excel para el procesamiento de los datos adquiridos. (Abstract. The present work was carried out in the Factory of Sodas 23 de Agosto, with the aim to evaluate the thermal efficiency of the boiler, determine the heat losses in uninsulated steam pipes; determine the environmental impact of flue gases generated; evaluate the boiler’s feedwater treatment system (water softener,as well as to make a techno-economic analysis of two improvement alternatives, consistent in: 1 Pre-heating of the feeding water to

Analysis of the retention of water vapor on silica gel; Analisis de la retencion del vapor de agua en silica gel

Energy Technology Data Exchange (ETDEWEB)

Herranz, M.; Pinilla, J. L.; Alegria, N.; Idoeta, R.; Legarda, F.

2011-07-01

Among the various sampling systems tritium content in the atmosphere as water vapor, one of the most basic and, therefore, of widespread use in the environmental field, is the retention on silica gel. However, the behavior of the collection efficiency of silica gel under varying conditions of air temperature and relative humidity makes it difficult to define the amount of this necessary for proper completion of sampling, especially in situations of prolonged sampling. This paper presents partial results obtained in a study on the analysis of these efficiencies under normal conditions of sampling. (Author)

Building blocks for ionic liquids: Vapor pressures and vaporization enthalpies of 1-(n-alkyl)-imidazoles

International Nuclear Information System (INIS)

Emel'yanenko, Vladimir N.; Portnova, Svetlana V.; Verevkin, Sergey P.; Skrzypczak, Andrzej; Schubert, Thomas

2011-01-01

Highlights: → We measured vapor pressures of the 1-(n-alkyl)-imidazoles by transpiration method. → Variations on the alkyl chain length n were C 3 , C 5 -C 7 , and C 9 -C 10 . → Enthalpies of vaporization were derived from (p, T) dependencies. → Enthalpies of vaporization at 298.15 K were linear dependent on the chain length. - Abstract: Vapor pressures of the linear 1-(n-alkyl)-imidazoles with the alkyl chain C 3 , C 5 -C 7 , and C 9 -C 10 have been measured by the transpiration method. The molar enthalpies of vaporization Δ l g H m of these compounds were derived from the temperature dependencies of vapor pressures. A linear correlation of enthalpies of vaporization Δ l g H m (298.15 K) of the 1-(n-alkyl)-imidazoles with the chain length has been found.

Vapor pressure and enthalpy of vaporization of oil of catnip by correlation gas chromatography

International Nuclear Information System (INIS)

Simmons, Daniel; Gobble, Chase; Chickos, James

2016-01-01

Highlights: • Vaporization enthalpies of the nepetalactones from oil of catnip have been evaluated. • Vapor pressures from T = (298.15 to 350) K have been evaluated. • Oil of catnip has a vapor pressure similar to DEET at T = 298.15 K. - Abstract: The vaporization enthalpy and vapor pressure of the two nepetalactones found in Nepeta cataria have been evaluated by correlation gas chromatography. Vaporization enthalpies at T = 298.15 K of {(68.0 ± 1.9) and (69.4 ± 1.9)} kJ ⋅ mol"−"1 have been derived for the minor diastereomer, (4aS,7S,7aS)-nepetalactone, and major one, (4aS,7S,7aR)-nepetalactone, respectively. Vapor pressures also at T = 298.15 K of p = (1.2 ± 0.04) Pa and (0.91 ± 0.03) Pa have been evaluated for the minor and the major stereoisomer. In addition to being of interest because of the remarkable effect it has on various felids, oil of catnip is also quite effective in repelling mosquitoes, comparable to diethyl-m-toluamide (DEET). The vapor pressures evaluated in this work suggest that the two stereoisomers have similar volatility to DEET at ambient temperatures.

Report of the seismic activity at the Cerro Prieto B.C., Mexico, geothermal field during 1996; Reporte de la actividad sismica registrada en el campo geotermico de Cerro Prieto, B.C., Mexico, durante 1996

Energy Technology Data Exchange (ETDEWEB)

Escamilla Hernandez, Abelardo [Gerencia de Proyectos Geotermoelectricos de la Comision Federal de Electricidad, Morelia (Mexico)

1997-05-01

In February 1996 started the operation of the Seismic Network of Cerro Prieto Geothermal Field (RESICP). It is constituted by five digital stations with velocity sensors of three components and a natural period of one second. The network worked continuously until December 2, 1996. During this period, we located 270 events in the field area and its neighborhood, with coda-length magnitude 1del Campo Geotermico de Cerro Prieto (RESICP); consta de cinco estaciones de tipo digital, sensores de velocidad de tres componentes, y periodo natural de un segundo. Trabajo en forma ininterrumpida hasta el 2 de diciembre de 1996. Durante ese periodo se localizaron

Update of Geothermics in Mexico

Energy Technology Data Exchange (ETDEWEB)

Gutierrez Negrin, Luis C.A.; Quijano Leon, Jose Luis [Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

2004-12-01

Four geothermal fields are currently operating in Mexico (Cerro Prieto, Los Azufres, Los Humeros and Las Tres Virgenes), with a total installed geothermal-electric capacity of 953 megawatts (MW). This means the country is located in third place, worldwide, just behind the USA and Philippines. Thirty-six power plants of several types (condensing, back pressure and binary cycle), between 1.5 and 110 MW, operate in the fields, fed by 197 wells with a combined production of 7,700 metric tons of steam per hour (t/h). These production wells have depths between 600 and 4,400 meters. Steam comes with 8,750 t/h of brine that is injected through 19 injection wells or treated in a solar evaporation pond of 14 km2 in Cerro Prieto. During 2003, steam produced in those fields equaled 67.5 million metric tons, and the power plants generated 6,282 gigawatt-hours (GWh), which represented 3.1% of the electric energy produced in Mexico. All the power plants and the geothermal fields are operated bye the public utility, the Comision Federal de Electricidad (Comision Federal de Electricidad (CFE)). [Spanish] Actualmente se operan en Mexico cuatro campos geotermicos (Cerro Prieto, Los Azufres, Los Humeros y Las Tres Virgenes), con una capacidad geotermoelectrica total de 953 megawatts (MW). Esto coloca al pais en el tercer lugar mundial, detras de Estados Unidos y Filipinas. En esos campos operan treinta y seis unidades de tipos diversos (a condensacion, a contrapresion y de ciclo binario), entre 1.5 y 110 MW, alimentadas por 197 pozos con una produccion combinada de 7,700 toneladas de vapor por hora (t/h). Estos pozos productores tienen profundidades entre 600 y 4,400 metros. El vapor sale acompanado por 8,750 t/h de salmuera, que se inyecta en 19 pozos inyectores o se trata en una laguna de evaporacion solar de 14 km2 en Cerro Prieto. Durante 2003 el vapor producido en los campos sumo 67.5 millones de toneladas y las unidades generaron 6,282 gigawatts-hora (GWh), lo que represento el

Vapor pressures and vaporization enthalpy of (−) α-bisabolol and (dl) menthol by correlation gas chromatography

International Nuclear Information System (INIS)

Keating, Leasa; Harris, Harold H.; Chickos, James S.

2017-01-01

Highlights: • The vaporization enthalpy and vapor pressure of (−) α-bisabolol and (dl)-menthol have been measured as a function of temperature. • Vapor pressures, vaporization enthalpies and boiling temperatures have been compared to available literature data. • Vapor pressures of (l)-menthol are compared to (dl)-menthol. - Abstract: The vapor pressures and vaporization enthalpies of (−) α-bisabolol and (dl)-menthol, two GRAS chemicals (generally recognized as safe) are evaluated by correlation gas chromatography using a series of saturated primary alcohols as standards. Vaporization enthalpies of (96.6 ± 2.4) and (74.2 ± 2.8) kJ mol −1 and vapor pressures of p/Pa = (0.020 ± 0.003) and (4.5 ± 0.44) were evaluated at T = 298.15 K for (−) α-bisabolol and (dl)-menthol, respectively, and compared to literature values. The vapor pressures of both compounds from T = (298.15 to 500) K have been derived from correlations using vapor pressures of a series of 1-alkanols and corresponding gas chromatographic retention times at 10 K intervals. The results were fit to a second order polynomial. Calculated normal boiling temperatures of T B = (574.8 and 492.7) K are calculated for (−) α-bisabolol and (dl)-menthol, respectively. A normal boiling temperature of T B = (485.2, and 489.7) K has previously been reported for (dl)-menthol. Vapor pressures for both (l)-menthol and (dl)-menthol from a previous study and (dl)-menthol from this study are compared with literature values.

Solution to the colloidal silica problem in the San Luis Potosi power plant; Solucion del problema de silice coloidal en la central termoelectrica San Luis Potosi

Energy Technology Data Exchange (ETDEWEB)

Lopez Rubalcava, Humberto [Comision Federal de Electricidad (CFE), Mexico, D. F. (Mexico); Mercado, Sergio [Instituto de Investigaciones Electricas, Cuernavaca (Mexico); Guerra, Protasio [Comision Federal de Electricidad (CFE), Mexico, D. F. (Mexico)

1988-12-31

eliminacion de silice coloidal, consistente en un sistema de ultrafiltracion de fibras huecas de 110 m{sup 3} de capacidad, que por primera vez se aplicaria en una central termoelectrica del pais. Se decidio instalar dicho sistema debido a que el agua de pozos que abastece la central proviene de un reservorio geotermico, con temperaturas de 38 grados celsius y con un contenido de 15 a 250 partes por billon (ppb) de silice coloidal, lo que hace necesario eliminarla para poder operar la caldera en sus condiciones de diseno (175 bars y 540 grados Celsius). Aunque se tenia una planta desmineralizadora para el tratamiento del agua de alimentacion, las resinas no retenian la silice coloidal. Asimismo, la operacion de la primera unidad se mantenia a 25% de su capacidad; al tratar de incrementarla a 50%, el contenido de silice rebasaba los limites permitidos en el agua de la caldera, dando 1,500 ppb en el agua y 28 ppb en el vapor. Una vez instalada la planta de ultrafiltracion, la central opero a plena carga obteniendose en el vapor valores inferiores al limite permitido de silice, es decir, de 10 partes por billon. A fines de 1987, entro en operacion la segunda unidad de 350 MW con equipo de ultrafiltracion, alcanzando la plena carga sin problemas. Comprobada la eficiencia de la ultrafiltracion para eliminar la silice coloidal del agua de alimentacion a la caldera, la CFE aplicara este sistema en otras centrales del pais, que tienen o tendran el mismo problema.

Melting temperature, vapor density, and vapor pressure of molybdenum pentafluoride

Energy Technology Data Exchange (ETDEWEB)

Krause, Jr, R F; Douglas, T B [National Bureau of Standards, Washington, D.C. (USA). Inst. for Materials Research

1977-12-01

A sample of MoF/sub 5/ was prepared by reaction of MoF/sub 6/(g) and Mo(c). Melting curves of temperature against time established the melting temperature at zero impurity to be 318.85 K, the enthalpy of fusion to be 6.1 kJ mol/sup -1/ (+ - 5 per cent), and the cryoscopic impurity of the sample to be 0.15 mole per cent. In the presence of MoF/sub 6/(g) which was added to suppress disproportionation, the vapor density of MoF/sub 5/ over the liquid was measured by the transpiration method at 343, 363, and 383 K, the total MoF/sub 5/ that evaporated being determined by permanganate titration. The total vapor pressure of MoF/sub 5/ oligomers over the liquid was measured by a simple static method at 373 and 392 K, while melting temperatures were taken alternately to monitor possible contamination of the sample. Although the vapor pressures were adjusted for disproportionation, solution of MoF/sub 6/ in MoF/sub 5/ (1), and wall adsorption of MoF/sub 6/ their percentage uncertainty is probably several times that of the vapor densities. A combination of the two properties indicates the average extent of association of the saturated vapor to be near 2, which is the value for the dimer species (MoF/sub 5/)/sub 2/.

R-22 vapor explosions

International Nuclear Information System (INIS)

Anderson, R.P.; Armstrong, D.R.

1977-01-01

Previous experimental and theoretical studies of R-22 vapor explosions are reviewed. Results from two experimental investigations of vapor explosions in a medium scale R-22/water system are reported. Measurements following the drop of an unrestrained mass of R-22 into a water tank demonstrated the existence of two types of interaction behavior. Release of a constrained mass of R-22 beneath the surface of a water tank improved the visual resolution of the system thus allowing identification of two interaction mechansims: at low water temperatures, R-22/water contact would produce immediate violent boiling; at high water temperatures a vapor film formed around its R-22 as it was released, explosions were generated by a surface wave which initiated at a single location and propagated along the vapor film as a shock wave. A new vapor explosion model is proposed, it suggests explosions are the result of a sequence of three independent steps: an initial mixing phase, a trigger and growth phase, and a mature phase where a propagating shock wave accelerates the two liquids into a collapsing vapor layer causing a high velocity impact which finely fragments and intermixes the two liquids

Piezoelectric trace vapor calibrator

International Nuclear Information System (INIS)

Verkouteren, R. Michael; Gillen, Greg; Taylor, David W.

2006-01-01

The design and performance of a vapor generator for calibration and testing of trace chemical sensors are described. The device utilizes piezoelectric ink-jet nozzles to dispense and vaporize precisely known amounts of analyte solutions as monodisperse droplets onto a hot ceramic surface, where the generated vapors are mixed with air before exiting the device. Injected droplets are monitored by microscope with strobed illumination, and the reproducibility of droplet volumes is optimized by adjustment of piezoelectric wave form parameters. Complete vaporization of the droplets occurs only across a 10 deg. C window within the transition boiling regime of the solvent, and the minimum and maximum rates of trace analyte that may be injected and evaporated are determined by thermodynamic principles and empirical observations of droplet formation and stability. By varying solution concentrations, droplet injection rates, air flow, and the number of active nozzles, the system is designed to deliver--on demand--continuous vapor concentrations across more than six orders of magnitude (nominally 290 fg/l to 1.05 μg/l). Vapor pulses containing femtogram to microgram quantities of analyte may also be generated. Calibrated ranges of three explosive vapors at ng/l levels were generated by the device and directly measured by ion mobility spectrometry (IMS). These data demonstrate expected linear trends within the limited working range of the IMS detector and also exhibit subtle nonlinear behavior from the IMS measurement process

Metodología de cálculo de la eficiencia térmica de generadores de vapor Methodology to calculate thermal efficiency of steam boilers

Directory of Open Access Journals (Sweden)

Marcos A. Golato

2008-07-01

Full Text Available Se desarrolló un método matemático determinístico de procesamiento de registros experimentales, aplicable a un sistema generador de vapor-precalentador de aire en estado estacionario, que opere con uno o dos combustibles simultáneamente, para determinar la eficiencia térmica del mismo y la eficiencia con la que se oxida el combustible, como así también el rendimiento del intercambiador de calor. La mecánica de procesamiento se basa en la resolución de los balances de materia y energía sobre los diferentes equipos que conforman el sistema. Esta metodología es aplicable a aquellos generadores de vapor que empleen, como combustible, bagazo, gas natural o ambos (caldera mixta. Se ilustran, como ejemplos de aplicación, los resultados del cálculo de la eficiencia térmica de diferentes generadores de vapor para cada tipo de combustible procesado, empleando para ello datos de diversos ensayos experimentales. La resolución de los balances de materia y energía en una caldera que quema bagazo, dio como resultado un rendimiento térmico del 53,2% y un índice de generación de 1,38 kg de vapor/ kg de bagazo. Para una caldera cuyo combustible es gas natural, se obtuvo un rendimiento térmico del 76,7% y un índice de generación de 9,8 kg de vapor/ Nm³ de gas natural. Para una caldera que quema en forma simultánea bagazo y gas natural, se determinó un rendimiento del 68,3% y un índice de generación de 1,87 kg de vapor/ kg de bagazo equivalente. Como validación de esta metodología, se contrastan estos valores de eficiencia con los obtenidos según el código propuesto por la American Society of Mechanical Engineers (ASME.A deterministic mathematical method for processing experimental data, applied to a steam generator-air heater system in stationary state which operates with one or two fuels simultaneously, was developed to determine the thermal of the system, as well as fuel combustion and heat exchanger efficiency. The methodology is

Fuel vapor pressure (FVAPRS)

International Nuclear Information System (INIS)

Mason, R.E.

1979-04-01

A subcode (FVAPRS) is described which calculates fuel vapor pressure. This subcode was developed as part of the fuel rod behavior modeling task performed at EG and G Idaho, Inc. The fuel vapor pressure subcode (FVAPRS), is presented and a discussion of literature data, steady state and transient fuel vapor pressure equations and estimates of the standard error of estimate to be expected with the FVAPRS subcode are included

Modeling of the vapor cycle of Laguna Verde with the PEPSE code to conditions of thermal power licensed at present (2027 MWt); Modelado del ciclo de vapor de Laguna Verde con el codigo PEPSE a condiciones de potencia termica actualmente licenciada (2027 MWt)

Energy Technology Data Exchange (ETDEWEB)

Castaneda G, M. A.; Maya G, F.; Medel C, J. E.; Cardenas J, J. B.; Cruz B, H. J.; Mercado V, J. J., E-mail: miguel.castaneda01@cfe.gob.mx [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Carretera Cardel-Nautla Km 42.5, Veracruz (Mexico)

2011-11-15

By means of the use of the performance evaluation of power system efficiencies (PEPSE) code was modeled the vapor cycle of the nuclear power station of Laguna Verde to reproduce the nuclear plant behavior to conditions of thermal power, licensed at present (2027 MWt); with the purpose of having a base line before the implementation of the project of extended power increase. The model of the gauged vapor cycle to reproduce the nuclear plant conditions makes use of the PEPSE model, design case of the vapor cycle of nuclear power station of Laguna Verde, which has as main components of the model the great equipment of the vapor cycle of Laguna Verde. The design case model makes use of information about the design requirements of each equipment for theoretically calculating the electric power of exit, besides thermodynamic conditions of the vapor cycle in different points. Starting from the design model and making use of data of the vapor cycle measured in the nuclear plant; the adjustment factors were calculated for the different equipment s of the vapor cycle, to reproduce with the PEPSE model the real vapor cycle of Laguna Verde. Once characterized the model of the vapor cycle of Laguna Verde, we can realize different sensibility studies to determine the effects macros to the vapor cycle by the variation of certain key parameters. (Author)

Vapor generation methods for explosives detection research

Energy Technology Data Exchange (ETDEWEB)

Grate, Jay W.; Ewing, Robert G.; Atkinson, David A.

2012-12-01

The generation of calibrated vapor samples of explosives compounds remains a challenge due to the low vapor pressures of the explosives, adsorption of explosives on container and tubing walls, and the requirement to manage (typically) multiple temperature zones as the vapor is generated, diluted, and delivered. Methods that have been described to generate vapors can be classified as continuous or pulsed flow vapor generators. Vapor sources for continuous flow generators are typically explosives compounds supported on a solid support, or compounds contained in a permeation or diffusion device. Sources are held at elevated isothermal temperatures. Similar sources can be used for pulsed vapor generators; however, pulsed systems may also use injection of solutions onto heated surfaces with generation of both solvent and explosives vapors, transient peaks from a gas chromatograph, or vapors generated by s programmed thermal desorption. This article reviews vapor generator approaches with emphasis on the method of generating the vapors and on practical aspects of vapor dilution and handling. In addition, a gas chromatographic system with two ovens that is configurable with up to four heating ropes is proposed that could serve as a single integrated platform for explosives vapor generation and device testing. Issues related to standards, calibration, and safety are also discussed.

EFECTO DEL SISTEMA DE RIEGO Y CLIMA EN LA EFICIENCIA DEL USO DE AGUA DE NOGAL PECANERO

Directory of Open Access Journals (Sweden)

Alejandro Zermeño González

2014-01-01

Full Text Available El nogal pecanero (Carya illinoensis K. es una especie frutícola de gran importancia para México, su cultivo se realiza en regiones de clima semidesértico donde el agua es el factor limitante de la producción, por lo que es necesario obtener la máxima eficiencia del uso de este recurso, que es función del sistema de riego y de las condiciones climáticas de la región. Sobre esta base, el objetivo de este estudio fue evaluar la eficiencia del uso del agua de dos huertas de nogal pecanero bajo dos sistemas de riego y diferentes condiciones climáticas. El estudio se realizó en el verano de 2008, en dos huertas de nogal pecanero del noreste de México: una de ellas ubicada en el sureste del estado de Coahuila (Mieleras, municipio de Matamoros con riego por goteo subsuperficial, y la otra en el norte del mismo estado (Zaragoza regada con aspersión. La eficiencia del uso del agua de las huertas del nogal pecanero se definió como la relación entre moles de CO2 asimilados por mol de agua evapotranspirada por el dosel de los árboles. Los resultados del estudio mostraron que aunque la asimilación de CO2 promedio diurna en la huerta de Mieleras (441.68 mmol m-2 fue estadísticamente igual a la observada en la huerta de Zaragoza (489.04 mmol m 2; la eficiencia promedio diaria del uso del agua (mmol CO2 mol-1 H2O fue mayor (P ≤ 0.05 en la huerta de Zaragoza (1.82 que la que se obtuvo en la huerta de Mieleras (1.42. Esto se debió a que las condiciones climáticas en Matamoros fueron de un mayor déficit de presión de vapor y una mayor tasa de evapotranspiración, que tuvieron un efecto mayor en la eficiencia del uso del agua que el sistema de riego utilizado en cada huerta.

The vaporization enthalpy and vapor pressure of S (+)-methamphetamine at T = 298.15 K by correlation gas chromatography

International Nuclear Information System (INIS)

Thornton, Melissa; Gobble, Chase; Chickos, James

2014-01-01

Highlights: • The vaporization enthalpy of (d)-methamphetamine was measured. • The vapor pressure of (d)-methamphetamine as a function of temperature was evaluated. • The vapor pressure of 4-benzylpiperidine as a function of temperature was evaluated. - Abstract: The vaporization enthalpy and vapor pressure of S (+)-methamphetamine is evaluated by correlation-gas chromatography. A vaporization enthalpy of (58.7 ± 4.3) kJ · mol −1 and a vapor pressure, p = (38 ± 9) Pa has been obtained using a variety of secondary aliphatic amines as standards. In addition, equations describing the vapor pressure temperature dependence are provided for standards and S (+)-methamphetamine covering the temperature range from T = 298.15 K to the boiling temperature. Boiling temperatures are reproduced within an interval of 8 K or less

Observation and particle simulation of vaporized W, Mo, and Be in PISCES-B plasma for vapor-shielding studies

Directory of Open Access Journals (Sweden)

K. Ibano

2017-08-01

Full Text Available Interactions of Tungsten (W, Molybdenum (Mo, and Beryllium (Be vapors with a steady-state plasma were studied by the PISCES-B liner plasma experiments as well as Particle-In-Cell (PIC simulations for the understanding of vapor-shielding phenomena. Effective cooling of the plasma by laser-generated Be vapor was observed in PISCES-B. On the other hand, no apparent cooling was observed for W and Mo vapors. The PIC simulation explains these experimental observations of the difference between low-Z and high-Z vapors. Decrease of electron temperature due to the vapor ejection was observed in case of a simulation of the Be vapor. As for the W vapor, it was found that the plasma cooling is localized only near the wall at a higher electron density plasma (∼1019m−3. On the other hand, the appreciable plasma cooling can be observed in a lower density plasma (∼1018m−3 for the W vapor.

Passive vapor extraction feasibility study

International Nuclear Information System (INIS)

Rohay, V.J.

1994-01-01

Demonstration of a passive vapor extraction remediation system is planned for sites in the 200 West Area used in the past for the disposal of waste liquids containing carbon tetrachloride. The passive vapor extraction units will consist of a 4-in.-diameter pipe, a check valve, a canister filled with granular activated carbon, and a wind turbine. The check valve will prevent inflow of air that otherwise would dilute the soil gas and make its subsequent extraction less efficient. The granular activated carbon is used to adsorb the carbon tetrachloride from the air. The wind turbine enhances extraction rates on windy days. Passive vapor extraction units will be designed and operated to meet all applicable or relevant and appropriate requirements. Based on a cost analysis, passive vapor extraction was found to be a cost-effective method for remediation of soils containing lower concentrations of volatile contaminants. Passive vapor extraction used on wells that average 10-stdft 3 /min air flow rates was found to be more cost effective than active vapor extraction for concentrations below 500 parts per million by volume (ppm) of carbon tetrachloride. For wells that average 5-stdft 3 /min air flow rates, passive vapor extraction is more cost effective below 100 ppm

A heated vapor cell unit for dichroic atomic vapor laser lock in atomic rubidium.

Science.gov (United States)

McCarron, Daniel J; Hughes, Ifan G; Tierney, Patrick; Cornish, Simon L

2007-09-01

The design and performance of a compact heated vapor cell unit for realizing a dichroic atomic vapor laser lock (DAVLL) for the D(2) transitions in atomic rubidium is described. A 5 cm long vapor cell is placed in a double-solenoid arrangement to produce the required magnetic field; the heat from the solenoid is used to increase the vapor pressure and correspondingly the DAVLL signal. We have characterized experimentally the dependence of important features of the DAVLL signal on magnetic field and cell temperature. For the weaker transitions both the amplitude and gradient of the signal are increased by an order of magnitude.

A heated vapor cell unit for dichroic atomic vapor laser lock in atomic rubidium

International Nuclear Information System (INIS)

McCarron, Daniel J.; Hughes, Ifan G.; Tierney, Patrick; Cornish, Simon L.

2007-01-01

The design and performance of a compact heated vapor cell unit for realizing a dichroic atomic vapor laser lock (DAVLL) for the D 2 transitions in atomic rubidium is described. A 5 cm long vapor cell is placed in a double-solenoid arrangement to produce the required magnetic field; the heat from the solenoid is used to increase the vapor pressure and correspondingly the DAVLL signal. We have characterized experimentally the dependence of important features of the DAVLL signal on magnetic field and cell temperature. For the weaker transitions both the amplitude and gradient of the signal are increased by an order of magnitude

High temperature vapors science and technology

CERN Document Server

Hastie, John

2012-01-01

High Temperature Vapors: Science and Technology focuses on the relationship of the basic science of high-temperature vapors to some areas of discernible practical importance in modern science and technology. The major high-temperature problem areas selected for discussion include chemical vapor transport and deposition; the vapor phase aspects of corrosion, combustion, and energy systems; and extraterrestrial high-temperature species. This book is comprised of seven chapters and begins with an introduction to the nature of the high-temperature vapor state, the scope and literature of high-temp

Copper-vapor-catalyzed chemical vapor deposition of graphene on dielectric substrates

Science.gov (United States)

Yang, Chao; Wu, Tianru; Wang, Haomin; Zhang, Xuefu; Shi, Zhiyuan; Xie, Xiaoming

2017-07-01

Direct synthesis of high-quality graphene on dielectric substrates is important for its application in electronics. In this work, we report the process of copper-vapor-catalyzed chemical vapor deposition of high-quality and large graphene domains on various dielectric substrates. The copper vapor plays a vital role on the growth of transfer-free graphene. Both single-crystal domains that are much larger than previous reports and high-coverage graphene films can be obtained by adjusting the growth duration. The quality of the obtained graphene was verified to be comparable with that of graphene grown on Cu foil. The progress reported in this work will aid the development of the application of transfer-free graphene in the future.

Estimated vapor pressure for WTP process streams

Energy Technology Data Exchange (ETDEWEB)

Pike, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Poirier, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-01-01

Design assumptions during the vacuum refill phase of the Pulsed Jet Mixers (PJMs) in the Hanford Waste Treatment and Immobilization Plant (WTP) equate the vapor pressure of all process streams to that of water when calculating the temperature at which the vacuum refill is reduced or eliminated. WTP design authority asked the authors to assess this assumption by performing calculations on proposed feed slurries to calculate the vapor pressure as a function of temperature. The vapor pressure was estimated for each WTP waste group. The vapor pressure suppression caused by dissolved solids is much greater than the increase caused by organic components such that the vapor pressure for all of the waste group compositions is less than that of pure water. The vapor pressure for each group at 145°F ranges from 81% to 98% of the vapor pressure of water. If desired, the PJM could be operated at higher temperatures for waste groups with high dissolved solids that suppress vapor pressure. The SO4 group with the highest vapor pressure suppression could be operated up to 153°F before reaching the same vapor pressure of water at 145°F. However, most groups would reach equivalent vapor pressure at 147 to 148°F. If any of these waste streams are diluted, the vapor pressure can exceed the vapor pressure of water at mass dilution ratios greater than 10, but the overall effect is less than 0.5%.

A numerical investigation of vapor intrusion--the dynamic response of contaminant vapors to rainfall events.

Science.gov (United States)

Shen, Rui; Pennell, Kelly G; Suuberg, Eric M

2012-10-15

The U.S. government and various agencies have published guidelines for field investigation of vapor intrusion, most of which suggest soil gas sampling as an integral part of the investigation. Contaminant soil gas data are often relatively more stable than indoor air vapor concentration measurements, but meteorological conditions might influence soil gas values. Although a few field and numerical studies have considered some temporal effects on soil gas vapor transport, a full explanation of the contaminant vapor concentration response to rainfall events is not available. This manuscript seeks to demonstrate the effects on soil vapor transport during and after different rainfall events, by applying a coupled numerical model of fluid flow and vapor transport. Both a single rainfall event and seasonal rainfall events were modeled. For the single rainfall event models, the vapor response process could be divided into three steps: namely, infiltration, water redistribution, and establishment of a water lens atop the groundwater source. In the infiltration step, rainfall intensity was found to determine the speed of the wetting front and wash-out effect on the vapor. The passage of the wetting front led to an increase of the vapor concentration in both the infiltration and water redistribution steps and this effect is noted at soil probes located 1m below the ground surface. When the mixing of groundwater with infiltrated water was not allowed, a clean water lens accumulated above the groundwater source and led to a capping effect which can reduce diffusion rates of contaminant from the source. Seasonal rainfall with short time intervals involved superposition of the individual rainfall events. This modeling results indicated that for relatively deeper soil that the infiltration wetting front could not flood, the effects were damped out in less than a month after rain; while in the long term (years), possible formation of a water lens played a larger role in determining

OPTIMIZACIÓN DEL RENDIMIENTO Y CONTENIDO DE TIMOL DE ACEITE ESENCIAL DE ORÉGANO SILVESTRE OBTENIDO POR ARRASTRE CON VAPOR OPTIMIZAÇÃO DO RENDIMENTO E CONTEÚDO DE TIMOL DO ÓLEO ESSENCIAL DO ORÉGANO SELVAGEM OBTIDO POR ARRASTRE À VAPOR OPTIMIZATION OF YIELD AND THYMOL CONTENT OF WILD OREGANO ESSENTIAL OIL OBTAINED BY STEAM DISTILLATION PROCESS

Directory of Open Access Journals (Sweden)

OSCAR ARANGO B

2012-12-01

Full Text Available Se estudió el proceso de extracción por arrastre con vapor a escala de planta piloto del aceite esencial de orégano silvestre (Lippia origanoides H.B.K de la región del Alto Patía (Colombia utilizando la metodología de superficie de respuesta. Los factores estudiados fueron el tiempo de extracción (1-3 horas, la densidad del lecho (60-100 g/L y la presión de extracción (1-3 psi. Las variables de respuesta fueron el rendimiento de extracción y el contenido de timol del aceite esencial. La composición de los aceites esenciales fue determinada mediante cromatografía de gases. Con respecto al rendimiento se obtuvo que solamente la densidad del lecho presentó un efecto estadísticamente significativo (PO processo de extração do óleo essencial de orégano silvestre (Lippia origanoides H.B.K por arraste a vapor foi estudado a escala piloto na região do Alto Patía (Colômbia, utilizando a metodologia de superfície resposta. Os fatores estudados foram o tempo de extração (1-3 horas, a densidade do leito (60-100 g/L e a pressão de extração (1-3 psi. As variáveis de resposta foram: o rendimento da extração e o conteúdo de timol do óleo essencial. A composição dos óleos essenciais foi determinada mediante cromatografia de gases. Com respeito ao rendimento, foi obtido que somente a densidade do leito apresentou um efeito estatisticamente significativo (PThe extraction process by steam distillation on pilot plant of essential oil from wild oregano (Lippia origanoides H.B.K from Alto Patía region (Colombia was studied using surface response methodology. Factors studied were the extraction time (1-3 hours, the density of the bed (60-100 g/L and the extraction pressure (1-3 psi. The response variables were the extraction yield and the content of thymol in the essential oil. The composition of essential oils was determined by gas chromatography. Regarding yield only the bed density presented a statistically significant effect (P

Vapor recovery system in the gasolines commercialization; Sistema de recuperacion de vapores en la comercializacion de las gasolinas

Energy Technology Data Exchange (ETDEWEB)

Casas Barba, R.; Molina Gallegos, J.R. [Instituto Mexicano del Petroleo (IMP), Mexico, D. F. (Mexico)

1995-12-31

In the last years the studies performed with respect to the environmental pollution show that the ozone is one of the most problematic contaminants in the Metropolitan Zone of Mexico City (MZMC) and that the hydrocarbons are the main forerunners of it. The main source of hydrocarbon vapor emissions originates from the handling and distribution operations. In this paper a description is made of the involved stages in the commercialization of gasolines in the MZMC and a description is also made of the systems employed to control the emissions in the three stages of the fuels storage and distribution cycle and explains the degree the hydrocarbon emissions to the atmosphere will be reduced, once the recovery systems are installed in all of the involved stages. [Espanol] En los ultimos anos los estudios realizados con respecto a contaminacion ambiental reflejan que el ozono es uno de los contaminantes mas problematicos de la zona metropolitana de la ciudad de Mexico (ZMCM), y los hidrocarburos son los principales precursores de este. La principal fuente de emision de vapores de hidrocarburos proviene de las operaciones de manejo y distribucion de combustibles. En este articulo se hace una descripcion de las etapas involucradas en la comercializacion de las gasolinas en la ZMCM, se describen tambien los sistemas utilizados para controlar las emisiones en las tres etapas del ciclo de almacenamiento y distribucion de combustibles y se explica en que grado se reduciran las emisiones de hidrocarburos a la atmosfera, una vez que se instalen los sistemas de recuperacion en todas las etapas involucradas.

Vapor recovery system in the gasolines commercialization; Sistema de recuperacion de vapores en la comercializacion de las gasolinas

Energy Technology Data Exchange (ETDEWEB)

Casas Barba, R; Molina Gallegos, J R [Instituto Mexicano del Petroleo (IMP), Mexico, D. F. (Mexico)

1996-12-31

In the last years the studies performed with respect to the environmental pollution show that the ozone is one of the most problematic contaminants in the Metropolitan Zone of Mexico City (MZMC) and that the hydrocarbons are the main forerunners of it. The main source of hydrocarbon vapor emissions originates from the handling and distribution operations. In this paper a description is made of the involved stages in the commercialization of gasolines in the MZMC and a description is also made of the systems employed to control the emissions in the three stages of the fuels storage and distribution cycle and explains the degree the hydrocarbon emissions to the atmosphere will be reduced, once the recovery systems are installed in all of the involved stages. [Espanol] En los ultimos anos los estudios realizados con respecto a contaminacion ambiental reflejan que el ozono es uno de los contaminantes mas problematicos de la zona metropolitana de la ciudad de Mexico (ZMCM), y los hidrocarburos son los principales precursores de este. La principal fuente de emision de vapores de hidrocarburos proviene de las operaciones de manejo y distribucion de combustibles. En este articulo se hace una descripcion de las etapas involucradas en la comercializacion de las gasolinas en la ZMCM, se describen tambien los sistemas utilizados para controlar las emisiones en las tres etapas del ciclo de almacenamiento y distribucion de combustibles y se explica en que grado se reduciran las emisiones de hidrocarburos a la atmosfera, una vez que se instalen los sistemas de recuperacion en todas las etapas involucradas.

Behavior patterns of chemical and isotopic species (2006-2007) in the Los Azufres, Mich., geothermal field, as a response to reinjection; Patrones de comportamiento de especies quimicas e isotopicas (2006-2007) en el campo geotermico de Los Azufres, Mich., en respuesta a la reinyeccion

Energy Technology Data Exchange (ETDEWEB)

Barragan R, Rosa Maria; Arellano G, Victor Manuel; Martinez E, Ignacio; Aragon A, Alfonso [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: rmb@iie.org.mx; Reyes D, Lisette; Gonzalez, Rubi [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Residencia de Los Azufres, Morelia, Michoacan (Mexico)

2009-07-15

quimicos e isotopicos ({delta}18 O y {delta}D) de fluidos de pozos del campo geotermico de Los Azufres, Mich., obtenidos en 2006 y 2007, para investigar los cambios ocurridos en sus patrones de comportamiento y su relacion con el proceso de reinyeccion de fluidos al yacimiento. El analisis de los datos comprendio las estimaciones de cloruros en las descargas totales, temperaturas de yacimiento, exceso de vapor en los fluidos de alimentacion, las concentraciones de CO{sub 2} en las descargas totales y en la fase liquida del yacimiento y las saturaciones de liquido en la formacion. Con los resultados se elaboraron mapas de isovalores de los parametros mencionados correspondientes a 2006 y 2007 para investigar su evolucion con respecto a los mapas obtenidos en 2005, asi como su relacion con las historias de reinyeccion. Se correlacionaron las composiciones isotopicas de los fluidos incluyendo los de reinyeccion para estimar efectos de mezcla de fluidos. Los resultados indican que las variables estudiadas responden a las tasas de reinyeccion en el campo. Las relaciones {delta}D vs {delta}18 O indican que un buen numero de pozos del campo producen diferentes proporciones de retornos de reinyeccion; en la zona norte los pozos AZ-65D, AZ-13, AZ-32, AZ-9A, AZ-9AD, AZ-28A, AZ-69D y AZ-44 producen una mayor proporcion mientras que los pozos AZ-5, AZ-28 y AZ-19 entre otros, producen una menor proporcion. En la zona sur los pozos AZ-2A, AZ-16AD, AZ-46 y AZ-33 producen relativamente altas proporciones de retornos de reinyeccion mientras que los pozos AZ-34, AZ-36 y AZ-37 producen menores proporciones. La distribucion de saturaciones de liquido hallada en 2007 muestra que las areas de maxima saturacion han disminuido con respecto a las distribuciones de este parametro en 2005 y 2006. En 2007 las saturaciones maximas de liquido se localizaron alrededor de los pozos AZ-22 y AZ-23 (zona sur) y AZ-28, AZ-32, AZ-45 y AZ-48 (zona norte), mientras que las saturaciones minimas se localizaron en

Model to predict the flow of tracers in naturally fractured geothermal reservoirs; Modelo para predecir el flujo de trazadores en yacimientos geotermicos naturalmente fracturados

Energy Technology Data Exchange (ETDEWEB)

Ramirez Sabag, Jetzabeth

1988-02-01

{sub e1} fixes the characteristic of the family of curves. Also it was found that the irruption time for a given concentration depends strongly on {alpha}. [Spanish] El modelo propuesto ha sido desarrollado para estudiar el flujo de trazadores a traves de yacimientos geotermicos naturalmente fracturados. El sistema idealizado del yacimiento esta compuesto por dos regiones: Una region movil donde mecanismos de difusion y conveccion estan presentes y una region estancada o inmovil donde se consideran los mecanismos de difusion y adsorcion: en ambas regiones se considera la perdida de masa por decaimiento radioactivo. Las soluciones de las ecuaciones basicas de flujo estan en el espacio de Laplace y se utilizo el algoritmo de Stehfest para su inversion numerica. A pesar de la dispersion numerica que presentan estas soluciones, se encontro una tendencia bien definida para inferir el comportamiento del sistema bajo diferentes condiciones de flujo. Se encontro que, para propositos practicos el tamano de los bloques de matriz no tiene influencia sobre la respuesta de la concentracion, y la solucion se reduce a la presentada por Tang y asociados. Bajo estas condiciones, el comportamiento del sistema puede ser descrito por dos parametros adimensionales: El numero de Peclet en las fracturas y un parametro. Se derivo tambien la respuesta del trazador para la solucion pico. Se encontro una solucion analitica limite para el caso en que {alpha} tienda a cero, el cual corresponde al caso de un sistema homogeneo. Se comprobo que esta solucion limite es valida, para {alpha}<0.01. Para el caso de inyeccion continua esta solucion se reduce a la presentada por Coasts y Smith. Para la solucion pico, se encontro que el tiempo de irrupcion correspondiente a la maxima concentracion esta relacionada directamente con el grupo adimensional. Por lo tanto, es posible obtener el valor de P{sub e1} para una X{sub D} dada, o viceversa. Un grupo de graficas de concentracion adimensional en la fractura

Vapor Pressure Data Analysis and Statistics

Science.gov (United States)

2016-12-01

near 8, 2000, and 200, respectively. The A (or a) value is directly related to vapor pressure and will be greater for high vapor pressure materials...1, (10) where n is the number of data points, Yi is the natural logarithm of the i th experimental vapor pressure value, and Xi is the...VAPOR PRESSURE DATA ANALYSIS AND STATISTICS ECBC-TR-1422 Ann Brozena RESEARCH AND TECHNOLOGY DIRECTORATE

Evaluación agroindustrial de los aceites esenciales de Artemisia dracunculos L, Franseria artemisioides Willd, Salvia officinalis L, Lippia dulcis Frev, y Occimun americanum L en condiciones del Valle del Cauca Agroindustrial evaluation of essential oils of Artemisia dracunculos L, Franseria artemisioides Willd, Salvia officinalis L, Lippia dulcis Frev, and Occimun americanum L in conditions of the Cauca Valle

OpenAIRE

Luis F Saldarriaga C; Ginna M Sánchez M; Carmen Rosa Bonilla Correa; Manuel Salvador Sánchez Orozco; Harlen Gerardo Torres Castañeda

2010-01-01

En parcelas establecidas de la Colección de Trabajo de Plantas Medicinales del Centro Experimental CEUNP en condiciones del departamento del Valle del Cauca, se tomaron muestras del material vegetal mediante el corte manual en un marco de 0.25m² ; se separaron hojas, tallos y flores de cada especie. Se determinó el porcentaje de materia seca y se acondicionó para el proceso de extracción de aceite esencial mediante arrastre con vapor. A los aceites obtenidos se les midió la densidad, y el índ...

A Simple Experiment for Determining Vapor Pressure and Enthalpy of Vaporization of Water.

Science.gov (United States)

Levinson, Gerald S.

1982-01-01

Laboratory procedures, calculations, and sample results are described for a freshman chemistry experiment in which the Clausius-Clapeyron equation is introduced as a means of describing the variation of vapor pressure with temperature and for determining enthalpy of vaporization. (Author/SK)

Improvements to vapor generators

International Nuclear Information System (INIS)

Keller, Arthur; Monroe, Neil.

1976-01-01

A supporting system is proposed for vapor generators of the 'supported' type. Said supporting system is intended to compensate the disparities of thermal expansion due to the differences in the vertical dimensions of the tubes in the walls of the combustion chamber and their collectors compared to that of the balloon tanks and the connecting tube clusters of vaporization, the first one being longer than the second ones. Said system makes it possible to build said combustion chamber higher than the balloon tanks and the tube clusters of vaporization. The capacity of steam production is thus enhanced [fr

DSMC simulations of vapor transport toward development of the lithium vapor box divertor concept

Science.gov (United States)

Jagoe, Christopher; Schwartz, Jacob; Goldston, Robert

2016-10-01

The lithium vapor divertor box concept attempts to achieve volumetric dissipation of the high heat efflux from a fusion power system. The vapor extracts the heat of the incoming plasma by ionization and radiation, while remaining localized in the vapor box due to differential pumping based on rapid condensation. Preliminary calculations with lithium vapor at densities appropriate for an NSTX-U-scale machine give Knudsen numbers between 0.01 and 1, outside both the range of continuum fluid dynamics and of collisionless Monte Carlo. The direct-simulation Monte Carlo (DSMC) method, however, can simulate rarefied gas flows in this regime. Using the solver contained in the OpenFOAM package, pressure-driven flows of water vapor will be analyzed. The use of water vapor in the relevant range of Knudsen number allows for a flexible similarity experiment to verify the reliability of the code before moving to tests with lithium. The simulation geometry consists of chains of boxes on a temperature gradient, connected by slots with widths that are a representative fraction of the dimensions of the box. We expect choked flow, sonic shocks, and order-of-magnitude pressure and density drops from box to box, but this expectation will be tested in the simulation and then experiment. This work is supported by the Princeton Environmental Institute.

Thermogravimetric measurements of liquid vapor pressure

International Nuclear Information System (INIS)

Rong Yunhong; Gregson, Christopher M.; Parker, Alan

2012-01-01

Highlights: ► Rapid determination of vapor pressure by TGA. ► Demonstration of limitations of currently available approaches in literature. ► New model for vapor pressure assessment of small size samples in TGA. ► New model accounts for vapor diffusion and sample geometry and measures vapor pressure normally within 10%. - Abstract: A method was developed using thermo-gravimetric analysis (TGA) to determine the vapor pressure of volatile liquids. This is achieved by measuring the rate of evaporation (mass loss) of a pure liquid contained within a cylindrical pan. The influence of factors like sample geometry and vapor diffusion on evaporation rate are discussed. The measurement can be performed across a wide range of temperature yielding reasonable results up to 10 kPa. This approach may be useful as a rapid and automatable method for measuring the volatility of flavor and fragrance raw materials.

Petroleum Vapor - Field Technical

Science.gov (United States)

The screening approach being developed by EPA OUST to evaluate petroleum vapor intrusion (PVI) requires information that has not be routinely collected in the past at vapor intrusion sites. What is the best way to collect this data? What are the relevant data quality issues and ...

A Numerical Investigation of Vapor Intrusion — the Dynamic Response of Contaminant Vapors to Rainfall Events

Science.gov (United States)

Shen, Rui; Pennell, Kelly G.; Suuberg, Eric M.

2013-01-01

The U.S. government and various agencies have published guidelines for field investigation of vapor intrusion, most of which suggest soil gas sampling as an integral part of the investigation. Contaminant soil gas data are often relatively more stable than indoor air vapor concentration measurements, but meteorological conditions might influence soil gas values. Although a few field and numerical studies have considered some temporal effects on soil gas vapor transport, a full explanation of the contaminant vapor concentration response to rainfall events is not available. This manuscript seeks to demonstrate the effects on soil vapor transport during and after different rainfall events, by applying a coupled numerical model of fluid flow and vapor transport. Both a single rainfall event and seasonal rainfall events were modeled. For the single rainfall event models, the vapor response process could be divided into three steps: namely, infiltration, water redistribution, and establishment of a water lens atop the groundwater source. In the infiltration step, rainfall intensity was found to determine the speed of the wetting front and wash-out effect on the vapor. The passage of the wetting front led to an increase of the vapor concentration in both the infiltration and water redistribution steps and this effect is noted at soil probes located 1 m below the ground surface. When the mixing of groundwater with infiltrated water was not allowed, a clean water lens accumulated above the groundwater source and led to a capping effect which can reduce diffusion rates of contaminant from the source. Seasonal rainfall with short time intervals involved superposition of the individual rainfall events. This modeling results indicated that for relatively deeper soil that the infiltration wetting front could not flood, the effects were damped out in less than a month after rain; while in the long term (years), possible formation of a water lens played a larger role in

Research on heat pumps in Mexico operating with geothermal energy and waste heat; Investigacion sobre bombas de calor en Mexico operando con energia geotermica y calor de desecho

Energy Technology Data Exchange (ETDEWEB)

Garcia-Gutierrez, A; Barragan-Reyes, R.M; Arellano-Gomez, V [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: aggarcia@iie.org.mx

2008-01-15

The Instituto de Investigaciones Electricas and the Comision Federal de Electricidad have done research and development (R&D) on heat pumps (HP) in past years. Tested systems include mechanical compression, absorption and heat-transformers. The main R&D aspects on HP are briefly described, and also a more detailed description about three of the main studies is presented: (a) a mechanical compression HP of the water-water type operated with low-pressure geothermal steam at the Los Azufres; Mich., geothermal field, and designed for purification of brine; (b) an absorption HP for cooling and refrigeration operating with ammonia-water and low-enthalpy geothermal energy, which was tested in the Los Azufres and Cerro Prieto, BC, geothermal fields; and (c) a heat-transformer by absorption-Absorption Heat Pump Type II-tested to assess the performance of several ternary solutions as work fluids. Plans exist to install and test a geothermal heat pump at Cerro Prieto or Mexicali, BC. [Spanish] El Instituto de Investigaciones Electricas y la Comision Federal de Electricidad han realizado trabajo de investigacion y desarrollo (I&D) sobre bombas de calor (BC) en el pasado. Los sistemas probados incluyen compresion mecanica, absorcion y transformadores termicos. Este trabajo describe brevemente los principales aspectos de I&D sobre bombas de calor en forma general, y se da una descripcion mas detallada de tres de los principales estudios: (a) una BC por compresion mecanica tipo agua-agua disenada para purificacion de salmueras operando con vapor geotermico de baja presion en el campo geotermico de Los Azufres, Mich.; (b) una BC por absorcion para enfriamiento y refrigeracion operando con amoniaco-agua y energia geotermica de baja entalpia, la cual fue probada en los campos geotermicos de Los Azufres y Cerro Prieto, BC; y (c) un transformador termico por absorcion -llamado Bomba de Calor por Absorcion Tipo II--, el cual fue probado para evaluar el comportamiento de diversas

Starting of the steam generator of a fossil fuel power plant, using predictive control based in a neuronal model; Arranque del generador de vapor de una central termoelectrica, usando control predictivo basado en un modelo neuronal

Energy Technology Data Exchange (ETDEWEB)

Gallardo Dominguez, Tonatiuh

2004-09-15

In this thesis work it is presented the design and implementation of a simulator of total scope of a predictive controller based in the neuronal model of the temperature in two stages of the heating of the steam generator of a fossil fuel power plant. An implemented control scheme is detailed, as well as the methodology for the identification of a neuronal model utilized for the control. Finally the results of the implementation in the simulator located at the Instituto de Investigaciones Electricas (IIE) are shown to be satisfactory. This control structure is not applied directly in closed circuit, but provides the value of the control actions to a human operator. [Spanish] En este trabajo de tesis se presenta el diseno e implementacion, en un simulador de alcance total, de un controlador predictivo basado en un modelo neuronal para el control de la temperatura en dos etapas del calentamiento del generador de vapor de una central termoelectrica. Se detalla el esquema de control implementado, asi como la metodologia de identificacion de un modelo neuronal utilizado para la sintesis del control. Finalmente se muestran los resultados de la implementacion en el simulador que se encuentra en el Instituto de Investigaciones Electricas (IIE); dichos resultados fueron satisfactorios. Esta estructura de control no se aplica directamente en lazo cerrado, sino que provee el valor de las acciones de control a un operador humano.

The lithium vapor box divertor

International Nuclear Information System (INIS)

Goldston, R J; Schwartz, J; Myers, R

2016-01-01

It has long been recognized that volumetric dissipation of the plasma heat flux from a fusion power system is preferable to its localized impingement on a material surface. Volumetric dissipation mitigates both the anticipated very high heat flux and intense particle-induced damage due to sputtering. Recent projections to a tokamak demonstration power plant suggest an immense upstream parallel heat flux, of order 20 GW m −2 , implying that fully detached operation may be a requirement for the success of fusion power. Building on pioneering work on the use of lithium by Nagayama et al and by Ono et al as well as earlier work on the gas box divertor by Watkins and Rebut, we present here a concept for a lithium vapor box divertor, in which lithium vapor extracts momentum and energy from a fusion-power-plant divertor plasma, using fully volumetric processes. At the high powers and pressures that are projected this requires a high density of lithium vapor, which must be isolated from the main plasma in order to avoid lithium build-up on the chamber walls or in the plasma. Isolation is achieved through a powerful multi-box differential pumping scheme available only for condensable vapors. The preliminary box-wise calculations are encouraging, but much more work is required to demonstrate the practical viability of this scheme, taking into account at least 2D plasma and vapor flows within and between the vapor boxes and out of the vapor boxes to the main plasma. (paper)

Vapor pressures and enthalpies of vaporization of a series of the linear aliphatic aldehydes

Czech Academy of Sciences Publication Activity Database

Verevkin, S. P.; Krasnykh, E. L.; Vasiltsova, T. V.; Koutek, Bohumír; Doubský, Jan; Heintz, A.

2003-01-01

Roč. 206, - (2003), s. 331-339 ISSN 0378-3812 Institutional research plan: CEZ:AV0Z4055905 Keywords : aldehydes * vapor pressure * enthalpy of vaporization Subject RIV: CC - Organic Chemistry Impact factor: 1.165, year: 2003

Vapor pressures and enthalpies of vaporization of a series of γ and δ-lactones by correlation gas chromatography

International Nuclear Information System (INIS)

Kozlovskiy, Mikhail; Gobble, Chase; Chickos, James

2014-01-01

Highlights: • The vaporization enthalpies of γ-octanolactone, γ- and δ-undecanolactone and γ and δ-dodecanolactone are reported. • Equations for predicting the vapor pressures over the temperature range T = (298.15 to 350) K are provided. • Vaporization enthalpies are compared to predicted values. - Abstract: The vaporization enthalpies of γ-octanolactone, γ- and δ-undecanolactone and γ and δ-dodecanolactone used commercially as flavor ingredients are reported as are their vapor pressures over the temperature range T = (298.15 to 350) K. Vaporization enthalpies at T = 298.15 K of: (66.0 ± 3.9), (79.4 ± 4.4), (80.1 ± 4.5), (83.9 ± 4.6), and (84.61 ± 4.7) kJ · mol −1 and vapor pressures also at T = 298.15 K of: (2.8 ± 0.9), (0.12 ± 0.05), (0.09 ± 0.04), (0.04 ± 0.02), and (0.03 ± 0.02) Pa, respectively, have been evaluated by correlation gas chromatography experiments. The vaporization enthalpies of the lactones studied are reproduced within ±0.5 kJ · mol −1 using a group additivity scheme reported previously for γ- and δ-lactones. The vaporization enthalpies of the γ- and δ-lactones are compared to a similar series of ω-lactones

A study on vapor explosions

International Nuclear Information System (INIS)

Takagi, N.; Shoji, M.

1979-01-01

An experimental study was carried out for vapor explosions of molten tin falling in water. For various initial metal temperatures and subcooling of water, transient pressure of the explosions, relative frequency of the explosions and the position where the explosions occur were measured in detail. The influence of ambient pressure was also investigated. From the results, it was concluded that the vapor explosion is closely related to the collapse of a vapor film around the molten metal. (author)

Physical model for vaporization

OpenAIRE

Garai, Jozsef

2006-01-01

Based on two assumptions, the surface layer is flexible, and the internal energy of the latent heat of vaporization is completely utilized by the atoms for overcoming on the surface resistance of the liquid, the enthalpy of vaporization was calculated for 45 elements. The theoretical values were tested against experiments with positive result.

Vaporization of irradiated droplets

International Nuclear Information System (INIS)

Armstrong, R.L.; O'Rourke, P.J.; Zardecki, A.

1986-01-01

The vaporization of a spherically symmetric liquid droplet subject to a high-intensity laser flux is investigated on the basis of a hydrodynamic description of the system composed of the vapor and ambient gas. In the limit of the convective vaporization, the boundary conditions at the fluid--gas interface are formulated by using the notion of a Knudsen layer in which translational equilibrium is established. This leads to approximate jump conditions at the interface. For homogeneous energy deposition, the hydrodynamic equations are solved numerically with the aid of the CON1D computer code (''CON1D: A computer program for calculating spherically symmetric droplet combustion,'' Los Alamos National Laboratory Report No. LA-10269-MS, December, 1984), based on the implict continuous--fluid Eulerian (ICE) [J. Comput. Phys. 8, 197 (1971)] and arbitrary Lagrangian--Eulerian (ALE) [J. Comput. Phys. 14, 1227 (1974)] numerical mehtods. The solutions exhibit the existence of two shock waves propagating in opposite directions with respect to the contact discontinuity surface that separates the ambient gas and vapor

Non-equilibrium phenomena near vapor-liquid interfaces

CERN Document Server

Kryukov, Alexei; Puzina, Yulia

2013-01-01

This book presents information on the development of a non-equilibrium approach to the study of heat and mass transfer problems using vapor-liquid interfaces, and demonstrates its application to a broad range of problems. In the process, the following peculiarities become apparent: 1. At vapor condensation on the interface from gas-vapor mixture, non-condensable components can lock up the interface surface and condensation stops completely. 2. At the evolution of vapor film on the heater in superfluid helium (He-II), the boiling mass flux density from the vapor-liquid interface is effectively zero at the macroscopic scale. 3. In problems concerning the motion of He-II bridges inside capillaries filled by vapor, in the presence of axial heat flux the He-II bridge cannot move from the heater as would a traditional liquid, but in the opposite direction instead. Thus the heater attracts the superfluid helium bridge. 4. The shape of liquid-vapor interface at film boiling on the axis-symmetric heaters immersed in l...

Effect of impact angle on vaporization

Science.gov (United States)

Schultz, Peter H.

1996-09-01

Impacts into easily vaporized targets such as dry ice and carbonates generate a rapidly expanding vapor cloud. Laboratory experiments performed in a tenuous atmosphere allow deriving the internal energy of this cloud through well-established and tested theoretical descriptions. A second set of experiments under near-vacuum conditions provides a second measure of energy as the internal energy converts to kinetic energy of expansion. The resulting data allow deriving the vaporized mass as a function of impact angle and velocity. Although peak shock pressures decrease with decreasing impact angle (referenced to horizontal), the amount of impact-generated vapor is found to increase and is derived from the upper surface. Moreover, the temperature of the vapor cloud appears to decrease with decreasing angle. These unexpected results are proposed to reflect the increasing roles of shear heating and downrange hypervelocity ricochet impacts created during oblique impacts. The shallow provenance, low temperature, and trajectory of such vapor have implications for larger-scale events, including enhancement of atmospheric and biospheric stress by oblique terrestrial impacts and impact recycling of the early atmosphere of Mars.

A Citizen's Guide to Vapor Intrusion Mitigation

Science.gov (United States)

This guide describes how vapor intrusion is the movement of chemical vapors from contaminated soil and groundwater into nearby buildings.Vapors primarily enter through openings in the building foundation or basement walls.

Condensation of vapor bubble in subcooled pool

Science.gov (United States)

Horiuchi, K.; Koiwa, Y.; Kaneko, T.; Ueno, I.

2017-02-01

We focus on condensation process of vapor bubble exposed to a pooled liquid of subcooled conditions. Two different geometries are employed in the present research; one is the evaporation on the heated surface, that is, subcooled pool boiling, and the other the injection of vapor into the subcooled pool. The test fluid is water, and all series of the experiments are conducted under the atmospheric pressure condition. The degree of subcooling is ranged from 10 to 40 K. Through the boiling experiment, unique phenomenon known as microbubble emission boiling (MEB) is introduced; this phenomenon realizes heat flux about 10 times higher than the critical heat flux. Condensation of the vapor bubble is the key phenomenon to supply ambient cold liquid to the heated surface. In order to understand the condensing process in the MEB, we prepare vapor in the vapor generator instead of the evaporation on the heated surface, and inject the vapor to expose the vapor bubble to the subcooled liquid. Special attention is paid to the dynamics of the vapor bubble detected by the high-speed video camera, and on the enhancement of the heat transfer due to the variation of interface area driven by the condensation.

Collapsing criteria for vapor film around solid spheres as a fundamental stage leading to vapor explosion

Energy Technology Data Exchange (ETDEWEB)

Freud, Roy [Nuclear Research Center - Negev, Beer-Sheva (Israel)], E-mail: freud@bgu.ac.il; Harari, Ronen [Nuclear Research Center - Negev, Beer-Sheva (Israel); Sher, Eran [Pearlstone Center for Aeronautical Studies, Department of Mechanical Engineering, Ben-Gurion University, Beer-Sheva (Israel)

2009-04-15

Following a partial fuel-melting accident, a Fuel-Coolant Interaction (FCI) can result with the fragmentation of the melt into tiny droplets. A vapor film is then formed between the melt fragments and the coolant, while preventing a contact between them. Triggering, propagation and expansion typically follow the premixing stage. In the triggering stage, vapor film collapse around one or several of the fragments occurs. This collapse can be the result of fragments cooling, a sort of mechanical force, or by any other means. When the vapor film collapses and the coolant re-establishes contact with the dry surface of the hot melt, it may lead to a very rapid and rather violent boiling. In the propagation stage the shock wave front leads to stripping of the films surrounding adjacent droplets which enhance the fragmentation and the process escalates. During this process a large quantity of liquid vaporizes and its expansion can result in destructive mechanical damage to the surrounding structures. This multiphase thermal detonation in which high pressure shock wave is formed is regarded as 'vapor explosion'. The film boiling and its possible collapse is a fundamental stage leading to vapor explosion. If the interaction of the melt and the coolant does not result in a film boiling, no explosion occurs. Many studies have been devoted to determine the minimum temperature and heat flux that is required to maintain a film boiling. The present experimental study examines the minimum temperature that is required to maintain a film boiling around metal spheres immersed into a liquid (subcooled distilled water) reservoir. In order to simulate fuel fragments that are small in dimension and has mirror-like surface, small spheres coated with anti-oxidation layer were used. The heat flux from the spheres was calculated from the sphere's temperature profiles and the sphere's properties. The vapor film collapse was associated with a sharp rise of the heat flux

Collapsing criteria for vapor film around solid spheres as a fundamental stage leading to vapor explosion

International Nuclear Information System (INIS)

Freud, Roy; Harari, Ronen; Sher, Eran

2009-01-01

Following a partial fuel-melting accident, a Fuel-Coolant Interaction (FCI) can result with the fragmentation of the melt into tiny droplets. A vapor film is then formed between the melt fragments and the coolant, while preventing a contact between them. Triggering, propagation and expansion typically follow the premixing stage. In the triggering stage, vapor film collapse around one or several of the fragments occurs. This collapse can be the result of fragments cooling, a sort of mechanical force, or by any other means. When the vapor film collapses and the coolant re-establishes contact with the dry surface of the hot melt, it may lead to a very rapid and rather violent boiling. In the propagation stage the shock wave front leads to stripping of the films surrounding adjacent droplets which enhance the fragmentation and the process escalates. During this process a large quantity of liquid vaporizes and its expansion can result in destructive mechanical damage to the surrounding structures. This multiphase thermal detonation in which high pressure shock wave is formed is regarded as 'vapor explosion'. The film boiling and its possible collapse is a fundamental stage leading to vapor explosion. If the interaction of the melt and the coolant does not result in a film boiling, no explosion occurs. Many studies have been devoted to determine the minimum temperature and heat flux that is required to maintain a film boiling. The present experimental study examines the minimum temperature that is required to maintain a film boiling around metal spheres immersed into a liquid (subcooled distilled water) reservoir. In order to simulate fuel fragments that are small in dimension and has mirror-like surface, small spheres coated with anti-oxidation layer were used. The heat flux from the spheres was calculated from the sphere's temperature profiles and the sphere's properties. The vapor film collapse was associated with a sharp rise of the heat flux during the cooling

Vapor deposition of tantalum and tantalum compounds

International Nuclear Information System (INIS)

Trkula, M.

1996-01-01

Tantalum, and many of its compounds, can be deposited as coatings with techniques ranging from pure, thermal chemical vapor deposition to pure physical vapor deposition. This review concentrates on chemical vapor deposition techniques. The paper takes a historical approach. The authors review classical, metal halide-based techniques and current techniques for tantalum chemical vapor deposition. The advantages and limitations of the techniques will be compared. The need for new lower temperature processes and hence new precursor chemicals will be examined and explained. In the last section, they add some speculation as to possible new, low-temperature precursors for tantalum chemical vapor deposition

Evidence of a sewer vapor transport pathway at the USEPA vapor intrusion research duplex

Science.gov (United States)

The role of sewer lines as preferential pathways for vapor intrusion is poorly understood. Although the importance of sewer lines for volatile organic compound (VOC) transport has been documented at a small number of sites with vapor intrusion, sewer lines are not routinely sampl...

Understanding and improving the chemical vapor deposition process for solar grade silicon production

OpenAIRE

Ramos Cabal, Alba

2015-01-01

Esta Tesis Doctoral se centra en la investigación del proceso de producción de polisilicio para aplicaciones fotovoltaicas (FV) por la vía química; mediante procesos de depósito en fase vapor (CVD). El polisilicio para la industria FV recibe el nombre de silicio de grado solar (SoG Si). Por un lado, el proceso que domina hoy en día la producción de SoG Si está basado en la síntesis, destilación y descomposición de triclorosilano (TCS) en un reactor CVD -denominado reactor Siemens-. El materia...

Knudsen cell vaporization of rare earth nitrides: enthalpy of vaporization of HoN098

International Nuclear Information System (INIS)

Brown, R.C.; Clark, N.J.

1975-01-01

The enthalpy of vaporization of HoN 0 . 98 was measured by the weight-loss Knudsen cell technique using Motzfeldt-Whitman extrapolations to zero orifice area. A third-law enthalpy of vaporization of HoN 0 . 98 of 155.9 +- 5 kcal mole -1 was obtained compared to a second-law value of 162.0 +- 5 kcal mole -1 . Similar measurements on the nitrides of samarium, erbium, and ytterbium gave third-law enthalpies of vaporization of 126.8 +-- 5 kcal mole -1 ; 159.6 +- 5 kcal mole -1 , and 121.0 +- 5 kcal mole -1 , respectively. 7 tables

Vapor pressures and vapor compositions in equilibrium with hypostoichiometric plutonium dioxide at high temperatures

International Nuclear Information System (INIS)

Green, D.W.; Fink, J.K.; Leibowitz, L.

1982-01-01

Vapor pressures and vapor compositions have been calculated for 1500 less than or equal to T less than or equal to 4000 0 K. Thermodynamic functions for the condensed phase and for each of the gaseous species were combined with an oxygen-potential model extended into the liquid region to obtain the partial pressures of O 2 , O, Pu, PuO and PuO 2 . The calculated oxygen pressures increase very rapidly as stoichiometry is approached. At least part of this increase is a consequence of the exclusion of Pu 6 + from the oxygen-potential model. No reliable method was found to estimate the importance of this ion. As a result of large oxygen potentials at high temperatures, extremely high total pressures that produced unreasonably high vapor densities were calculated. The highest temperature was therefore limited to 400 K, and the range of oxygen-to-metal ratios was limited to 1.994 to 1.70. These calculations show that vapor in equilibrium with hypostoichiometric plutonium dioxide is poorly approximated as PuO 2 for most of the temperture and composition range of interest. The vapor is much more oxygen-rich than the condensed phase. Implications for the (U,Pu)O/sub 2-x/ system are discussed

Vapor pressure measured with inflatable plastic bag

Science.gov (United States)

1965-01-01

Deflated plastic bag in a vacuum chamber measures initial low vapor pressures of materials. The bag captures the test sample vapors and visual observation of the vapor-inflated bag under increasing external pressures yields pertinent data.

Useful life extension of steam turbine rotors; Alargamiento de la vida en rotores de turbina de vapor

Energy Technology Data Exchange (ETDEWEB)

Garcia Arelle, Carlos [Turbomaquinas S. A. de C.V., La Piedad, Michoacan (Mexico)

2007-11-15

The continuous use of steam turbines, the chemistry of the steam itself and the variations of operation velocities, cause the gradual deterioration by erosion, oxidation and/or corrosion of the rotors and blades. When this happens most of the original manufacturers recommend to rectify the areas, diminishing the surfaces, or to compare with a new rotor. TURBOMAQUINARIAS S.A. de C.V. has developed the most reliable and safe methods to return the rotor to its original dimensions and in case of recurrent problems such as erosion, oxidation and/or wear, it offers the alternative of attaching coatings metallurgically compatible with which these problems are eliminated or diminished that might show up on the rotor surface as well as in the body of the discs or of the blades. These restoring methods are recommended by the international standards such as API 687. [Spanish] El uso continuo de las turbinas de vapor, la quimica del mismo vapor y la variacion de las velocidades de operacion, ocasionan el deterioro gradual por erosion, oxidacion y/o corrosion de los rotores y de los alabes. Al ocurrir esto la mayoria de los fabricantes originales recomiendan rectificar las areas, disminuyendo las superficies, o bien comparar un rotor nuevo. TURBOMAQUINARIAS S.A. de C.V. ha desarrollado los metodos mas confiables y seguros para devolver a su rotor las dimensiones originales y en caso de problemas recurrentes tales como erosion, oxidacion y/o desgaste, ofrece la alternativa de agregar recubrimientos metalurgicamente compatibles con los cuales se eliminan o se disminuyen estos problemas que pueden presentarse tanto en la superficie del rotor como del cuerpo de los discos o bien de los alabes. Estos metodos de restauracion son recomendados por las normas internacionales tales como la API 687.

Temperature dependences of saturated vapor pressure and the enthalpy of vaporization of n-pentyl esters of dicarboxylic acids

Science.gov (United States)

Portnova, S. V.; Krasnykh, E. L.; Levanova, S. V.

2016-05-01

The saturated vapor pressures and enthalpies of vaporization of n-pentyl esters of linear C2-C6 dicarboxylic acids are determined by the transpiration method in the temperature range of 309.2-361.2 K. The dependences of enthalpies of vaporization on the number of carbon atoms in the molecule and on the retention indices have been determined. The predictive capabilities of the existing calculation schemes for estimation of enthalpy of vaporization of the studied compounds have been analyzed.

Vapor-droplet flow equations

International Nuclear Information System (INIS)

Crowe, C.T.

1975-01-01

General features of a vapor-droplet flow are discussed and the equations expressing the conservation of mass, momentum, and energy for the vapor, liquid, and mixture using the control volume approach are derived. The phenomenological laws describing the exchange of mass, momentum, and energy between phases are also reviewed. The results have application to development of water-dominated geothermal resources

What Good is Raman Water Vapor Lidar?

Science.gov (United States)

Whitman, David

2011-01-01

Raman lidar has been used to quantify water vapor in the atmosphere for various scientific studies including mesoscale meteorology and satellite validation. Now the international networks of NDACC and GRUAN have interest in using Raman water vapor lidar for detecting trends in atmospheric water vapor concentrations. What are the data needs for addressing these very different measurement challenges. We will review briefly the scientific needs for water vapor accuracy for each of these three applications and attempt to translate that into performance specifications for Raman lidar in an effort to address the question in the title of "What good is Raman water vapor Iidar."

The necessity of renovation of the fundamental concepts of geochemistry for the geothermal systems; La necesidad de renovacion de los conceptos fundamentales de geoquimica para los sistemas geotermicos

Energy Technology Data Exchange (ETDEWEB)

Mahendra Jaiswal, Pal Verma [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

1999-07-01

In this article the exhaustive experimentation of the compilation of the experimental data of quartz solubility is presented along with the saturation curve water - steam and in the zone of compressed liquid. On the base of these data a regression relation was derived, which is valid for the entire range of temperature from 0 to 374 Celsius degrees. This study was developed by Mahendra Pal Verma Jaiswal, researcher of the Instituto de Investigaciones Electricas (IIE) [Spanish] En este articulo se presenta el experimento exhaustivo de la recopilacion de los datos experimentales de la solubilidad de cuarzo a lo largo de la curva de saturacion agua - vapor y en la zona de liquido comprimido. Sobre la base de estos datos se derivo una relacion de regresion, la cual es valida para todo el rango de temperatura desde 0 a 374 grados Celsius. Este estudio fue desarrollado por Mahendra Pal Verma Jaiswal, investigador del Instituto de Investigaciones Electricas (IIE)

Solution of the Rayleigh-Plesset Equation Through the Finite Element Method Solución de la ecuación de Rayleigh-Plesset por medio del método del elemento finito

Directory of Open Access Journals (Sweden)

G.A Ramírez R.

2013-03-01

Full Text Available In this work we present numerical solutions of the Rayleigh-Plesset equation which describes the evolution of cavitating bubbles. In order to do that, we consider FEMG (Finite Element Method Galerkin; this simulation is performed for an inviscid and incompressible fluid in an uniform temperature field with constant surface tension, and the cavitation model into the which the pressure inside bubbles is equal to the fluid vapor pressure. Thus, in this problem is considered the Dirichlet boundary problem, and we obtained criteria for the boundary conditions at the cavitation phenomenon through to the which give rise to the bubble growing.En este trabajo se plantean soluciones numéricas a la ecuación de Rayleigh-Plesset que describe la evolución de las burbujas en la cavitación. Para ello, se considera el MEFG (Método del Elemento Finito de Galerkin; tal simulación se realiza en un fluido invíscido e incompresible en un campo de temperatura uniforme, una tensión superficial esencialmente constante, y el modelo de cavitación en el flujo siendo la presión interna de las burbujas igual a la presión de vapor del fluido. De esta manera, para el problema se considera el problema de Dirichlet y se obtienen los criterios de frontera que auspician el fenómeno de cavitación a través del crecimiento de las burbujas o cavidades.

Ion vapor deposition and its application

International Nuclear Information System (INIS)

Bollinger, H.; Schulze, D.; Wilberg, R.

1981-01-01

Proceeding from the fundamentals of ion vapor deposition the characteristic properties of ion-plated coatings are briefly discussed. Examples are presented of successful applications of ion-plated coatings such as coatings with special electrical and dielectric properties, coatings for corrosion prevention, and coatings for improving the surface properties. It is concluded that ion vapor deposition is an advantageous procedure in addition to vapor deposition. (author)

Invasion of geothermal fluids into hydrocarbon reservoirs; La invasion de fluidos geotermicos en yacimientos de hidrocarburos

Energy Technology Data Exchange (ETDEWEB)

Suarez Arriaga, Mario Cesar [Universidad Michoacana, Facultad de Ciencias, Morelia, Michoacan (Mexico)]. E-mail: msuarez@umich.mx

2009-01-15

Oil reservoirs beneath the coast of the Gulf of Mexico contain geothermal brine at 150 degrees Celsius and produce a mixture of hot brine and oil. Water from an aquifer 6000 m deep flows vertically through conductive faults. These nonisothermal conditions affect the effective saturations and the relative permeability of the immiscible phases. Dynamic viscosities of oil and water diminish, affecting the displacement of both fluids. Studied wells produce from the oil-saturated zone above the aquifer, yet the total volume of produced water can equal or exceed the volume of oil. The presence of water is a severe problem. We produced an original numerical model able to predict the critical production when the wells start to be invaded by geothermal brine. The model has a single equation in partial derivatives, of a parabolic and nonlineal type, which is a function of water saturation, three-dimension space and time. A gas phase can be included in the model. This equation is a generalization of the classic isothermal result of Buckley-Leverett, in a single dimension. The model is solved numerically by using the Finite Element method on a nonstructured network. The historic effect of water invasion observed in some critical cases is reproduced. After production with both phases stable, a sudden brine invasion can occur with a sharp reduction of the oil volume produced. The immediate objective is to optimize the production so the well will be able to produce a stable water-oil mix where oil always prevails. [Spanish] Se reportan reservorios de aceite situados en la costa del Golfo de Mexico que son invadidos por salmuera geotermica con una temperatura de 150 grados centigrados, produciendo una mezcla variable de agua caliente y aceite. El agua de un acuifero, a 6000 metros de profundidad, fluye verticalmente por fallas conductivas. Estas condiciones no isotermicas afectan las saturaciones efectivas y las permeabilidades relativas de las fases inmiscibles. Las viscosidades

A Lithium Vapor Box Divertor Similarity Experiment

Science.gov (United States)

Cohen, Robert A.; Emdee, Eric D.; Goldston, Robert J.; Jaworski, Michael A.; Schwartz, Jacob A.

2017-10-01

A lithium vapor box divertor offers an alternate means of managing the extreme power density of divertor plasmas by leveraging gaseous lithium to volumetrically extract power. The vapor box divertor is a baffled slot with liquid lithium coated walls held at temperatures which increase toward the divertor floor. The resulting vapor pressure differential drives gaseous lithium from hotter chambers into cooler ones, where the lithium condenses and returns. A similarity experiment was devised to investigate the advantages offered by a vapor box divertor design. We discuss the design, construction, and early findings of the vapor box divertor experiment including vapor can construction, power transfer calculations, joint integrity tests, and thermocouple data logging. Heat redistribution of an incident plasma-based heat flux from a typical linear plasma device is also presented. This work supported by DOE Contract No. DE-AC02-09CH11466 and The Princeton Environmental Institute.

Hanford soil partitioning and vapor extraction study

International Nuclear Information System (INIS)

Yonge, D.; Hossain, A.; Cameron, R.; Ford, H.; Storey, C.

1996-07-01

This report describes the testing and results of laboratory experiments conducted to assist the carbon tetrachloride soil vapor extraction project operating in the 200 West Area of the Hanford Site in Richland, Washington. Vapor-phase adsorption and desorption testing was performed using carbon tetrachloride and Hanford Site soils to estimate vapor-soil partitioning and reasonably achievable carbon tetrachloride soil concentrations during active vapor extractions efforts at the 200 West Area. (CCl 4 is used in Pu recovery from aqueous streams.)

Caracterización del envejecimiento de tuberías de vapor de centrales térmicas empleando el efecto Barkhausen//Characterization of steam pipes ageing degree from power plants using magnetic Barkhausen noise

Directory of Open Access Journals (Sweden)

Frank de los Reyes-Rodríguez

2012-05-01

Full Text Available En este trabajo se caracteriza el grado de envejecimiento del acero 12Cr1MoV con el ruido magnético de Barkhausen por dos métodos. Para ello se realiza un estudio de la evolución microestructural en condiciones de operación (15MPa, 550ºC desde 100000 h a 150000 h, utilizando técnicas de microscopía óptica y electrónica de barrido. En el primer método los experimentos revelan una disminución de la raíz cuadrada media del voltaje con el tiempo de explotación, lo cual se atribuye a la disminución del número de paredes de dominio por unidad de área con el aumento del tamaño de grano. En el segundo método se evalúa el nivel de esferoidización y el tamaño medio de los carburos a partir de la altura total del segundo pico de la envolvente de la señal Barkhausen, mostrando una disminución debido a un cambio en la forma acicular y en el tamaño medio de los carburos. Palabras claves: grado de envejecimiento, ruido barkhausen, tuberías de vapor, carburos._______________________________________________________________________________ Abstract In this paper, an ageing degree characterization of 12Cr1MoV steel using two method of magnetic Barkhausen noise is developed. A study of the microstructural evolution during ageing at operated conditions (15MPa, 550ºC from 100000 h up to 150000 h was carried out using optic and scanning electron microscopy techniques. In the first method the experiments reveal a decreasing of root mean square of voltage with the ageing time, which is attributed to the decreasing of domain walls number per area units with the grain size increasing. In the second method the spheroidization level/average size of carbides was analyzed too with the total second peak height, determining a decreasing due to the change of the shape, size and acicularity of carbides phase. Key words: ageing degree, barkhausen noise, steam pipes, carbides.

Determination of forces induced by steam flow in turbines; Determinacion de fuerzas inducidas por flujo de vapor en turbinas

Energy Technology Data Exchange (ETDEWEB)

Garcia Castrejon, Juan Carlos

2008-09-15

blades, has a harmonic pattern. The pressure field variation as time function is uniform: the peaks and valleys across the axial clearance are always in phase. However the instant picture of the pressure field it's different: the peaks and valleys are not in phase and the number of peaks and valley changed across the clearance. In the case of the forces acting on blades, a Fourier on the forces calculated was used to determine the coefficients and frequency of a Fourier equation which can be used to calculate the alternating stresses on the blade in order to predict the useful life blades. [Spanish] Las vibraciones inducidas por flujo de vapor en turbinas representan uno de los problemas que enfrenta la operacion de turbinas de vapor cuya capacidad rebasa los 300 MW. Ademas estas constituyen uno de los limites tecnologicos para el desarrollo de turbinas de vapor de mas de 1 GW. Este tipo de fenomeno tiene su origen en la interaccion del rotor con el fluido que se encuentra en sus proximidades. El flujo de vapor dentro de la turbina es complejo, ya que es turbulento e inestable. A medida que el flujo pasa una etapa de estator o de rotor, se generan secundarios, vortices en los filos de salida, estelas con caracteristicas de flujo diferentes al flujo principal en los pasajes. Estas variaciones en el flujo son las que inducen vibraciones forzadas en los alabes. Ademas existen varios factores que contribuyen a la aplicacion de vibraciones en alabes inducidas por flujo como son: inestabilidad del flujo de vapor en los claros de los sellos, secuencia de apertura de las valvulas, estelas de las toberas, obstrucciones en algunas de las toberas y diferente espaciamiento en las toberas. Las vibraciones por flujo pueden ser peligrosas si su frecuencia coincide con la frecuencia natural del sistema, provocando efectos mas nocivos que las vibraciones por desbalance o por desalineamiento, pues tienen amplitudes mas grandes y provocan esfuerzos alternantes en los componentes del

Vapor trap for liquid metal

Energy Technology Data Exchange (ETDEWEB)

Watanabe, T

1968-05-22

In a pipe system which transfers liquid metal, inert gas (cover gas) is packed above the surface of the liquid metal to prevent oxidization of the liquid. If the metal vapor is contained in such cover gas, the circulating system of the cover gas is blocked due to condensation of liquid metal inside the system. The present invention relates to an improvement in vapor trap to remove the metal vapor from the cover gas. The trap consists of a cylindrical outer body, an inlet nozzle which is deeply inserted inside the outer body and has a number of holes to inject the cove gas into the body, metal mesh or steel wool which covers the exterior of the nozzle and on which the condensation of the metal gas takes place, and a heater wire hich is wound around the nozzle to prevent condensation of the metal vapor at the inner peripheral side of the mesh.

A preliminary interpretation of gas composition in the CP IV sector wells, Cerro Prieto geothermal field, Mexico

Energy Technology Data Exchange (ETDEWEB)

Barragan Reyes, Rosa Maria; Arellano Gomez, Victor M; Portugal Marin, Enrique [Instituto de Investigaciones Electricas, Gerencia de Geotermia, Morelos (Mexico)]. E-mail: rmb@iie.org.mx; Perez Hernandez, Alfredo; Rodriguez Rodriguez, Marco Helio; Leon Vivar, Jesus de [Comision Federal de Electricidad, Residencia General Cerro Prieto, B.C. (Mexico)

2007-07-15

-temperature fluids descending through the H fault to the reservoir was inferred, since results for the wells affected by this process (located at the center of the CP IV area) showed small or negative excess steam values and slightly lower temperatures (265-270 degrees Celsius). [Spanish] A fin de aumentar la capacidad de generacion de 620 a 720 MW, se desarrollo el sector Cerro Prieto IV (CP IV) en la porcion NE del campo geotermico de Cerro Prieto, donde se perforaron catorce pozos nuevos a partir del ano 2000. Los pozos de la zona de CP IV producen fluidos bifasicos con caracteristicas heterogeneas en cuanto a la fraccion de vapor: en la porcion central y hacia el NW los pozos producen liquido dominante mientras que hacia el E y S producen una fraccion de vapor relativamente alta. En este trabajo se estudia la composicion gaseosa de los fluidos producidos para obtener parametros del yacimiento tales como la temperatura y la fraccion de vapor e identificar diferentes aportes de fluidos a los pozos. Se utilizo un metodo basado en la reaccion de Fischer Tropsch y el equilibrio del H{sub 2}S con pirita-pirrotita como amortiguador (FT-HSH3). Los resultados para el estado inicial indican que existen fluidos con temperaturas de yacimiento entre 275 y 310 grados Celsius asi valores de exceso de vapor entre -1 y 50%. Los resultados se alinean en un patron de mezcla FT-HSH3 que sugiere que los pozos descargan una mezcla de los dos miembros finales en diferentes proporciones. Uno de ellos parece ser un liquido con una temperatura superior a los 300 grados Celsius con exceso de vapor negativo o insignificante. El otro parece ser un fluido bifasico con temperatura de unos 275 grados Celsius y un exceso de fraccion de vapor de aproximadamente 0.5. De acuerdo con datos de cada pozo y dependiendo de las condiciones de produccion de cada uno, pueden ocurrir mezclas de fluidos con diferentes proporciones de liquido y vapor en el yacimiento. Datos de 2005 de pozos perforados despues del ano 2000

Mechanics of gas-vapor bubbles

NARCIS (Netherlands)

Hao, Yue; Zhang, Yuhang; Prosperetti, Andrea

2017-01-01

Most bubbles contain a mixture of vapor and incondensible gases. While the limit cases of pure vapor and pure gas bubbles are well studied, much less is known about the more realistic case of a mixture. The bubble contents continuously change due to the combined effects of evaporation and

Vapor pressures and thermophysical properties of selected hexenols and recommended vapor pressure for hexan-1-ol

Czech Academy of Sciences Publication Activity Database

Štejfa, V.; Fulem, Michal; Růžička, K.; Matějka, P.

2015-01-01

Roč. 402, Sep (2015), 18-29 ISSN 0378-3812 Institutional support: RVO:68378271 Keywords : alcohols * vapor pressure * heat capacity * ideal - gas thermodynamic properties * vaporization enthalpy Subject RIV: BJ - Thermodynamics Impact factor: 1.846, year: 2015

Water vapor profiling using microwave radiometry

Science.gov (United States)

Wang, J. R.; Wilheit, T. T.

1988-01-01

Water vapor is one of the most important constituents in the Earth's atmosphere. Its spatial and temporal variations affect a wide spectrum of meteorological phenomena ranging from the formation of clouds to the development of severe storms. The passive microwave technique offers an excellent means for water vapor measurements. It can provide both day and night coverage under most cloud conditions. Two water vapor absorption features, at 22 and 183 GHz, were explored in the past years. The line strengths of these features differ by nearly two orders of magnitude. As a consequence, the techniques and the final products of water vapor measurements are also quite different. The research effort in the past few years was to improve and extend the retrieval algorithm to the measurements of water vapor profiles under cloudy conditions. In addition, the retrieval of total precipitable water using 183 GHz measurements, but in a manner analogous to the use of 22 GHz measurements, to increase measurement sensitivity for atmospheres of very low moisture content was also explored.

Distribution of tropical tropospheric water vapor

Science.gov (United States)

Sun, De-Zheng; Lindzen, Richard S.

1993-01-01

Utilizing a conceptual model for tropical convection and observational data for water vapor, the maintenance of the vertical distribution of the tropical tropospheric water vapor is discussed. While deep convection induces large-scale subsidence that constrains the turbulent downgradient mixing to within the convective boundary layer and effectively dries the troposphere through downward advection, it also pumps hydrometeors into the upper troposphere, whose subsequent evaporation appears to be the major source of moisture for the large-scale subsiding motion. The development of upper-level clouds and precipitation from these clouds may also act to dry the outflow, thus explaining the low relative humidity near the tropopause. A one-dimensional model is developed to simulate the mean vertical structure of water vapor in the tropical troposphere. It is also shown that the horizontal variation of water vapor in the tropical troposphere above the trade-wind boundary layer can be explained by the variation of a moisture source that is proportional to the amount of upper-level clouds. Implications for the nature of water vapor feedback in global warming are discussed.

Buscando luz en la tierra: bajo las bóvedas del Baño Real del Palacio de Comares

Directory of Open Access Journals (Sweden)

Miguel Guitart

2015-05-01

Full Text Available A lo largo de la cultura islámica se han producido soluciones espaciales de enorme riqueza arquitectónica y refinamiento estético, que no necesariamente material. El baño o hammam es con probabilidad uno de los más singulares. Procedente de las pautas establecidas por las termas romanas, estos baños se convirtieron en salas fundamentales de la vida social del mundo islámico. Cabría destacar en España ejem­plos tan relevantes como los Baños de Alí en Jaén del siglo X, el Bañuelo del Albaicín en Granada del siglo XI, o el más representativo de todos ellos, el Baño de Comares en el palacio-fortaleza de la Alhambra del siglo XIV. Todos ellos se caracterizan por sus bóvedas perforadas a modo de grandes moldes de luz que, si bien cumplían una misión funcional como la de introducir luz natural y regular la temperatura y la cantidad de vapor de agua en el interior, también transformaban por completo el espacio por medio de la luz y las sombras, haciendo de estas salas lugares muy característicos de su propia cultura. El hammam del Baño del Palacio de Comares, también conocido como Baño Real por haber sido de uso particular de los Reyes Católicos, se remonta a la época de Yusuf I (1333-1354. El Baño Real o de Comares constituye uno de los espacios de mayor interés dentro del conjunto de la Alhambra, con uno de los hammam en mejor estado de conservación hasta la fecha en Occidente, prácticamente íntegro a pesar de algunas modificaciones estructurales y un mantenimiento más testimonial que funcional. Podríamos asumir que el baño del Palacio de Comares se experimenta desde una doble estrategia: la del estatismo del baño como espacio consolidado y no cam­biante, relacionado por su masa y la condición original de la tierra de la que surge y sobre la que se asienta, que se infunde de vida al ser intervenida por la luz esce­nográfica del filtro de sus bóvedas; y la del movimiento establecido, del recorrido del visitante

HANFORD CHEMICAL VAPORS WORKER CONCERNS and EXPOSURE EVALUATION

International Nuclear Information System (INIS)

ANDERSON, T.J.

2006-01-01

Chemical vapor emissions from underground hazardous waste storage tanks on the Hanford site in eastern Washington State are a potential concern because workers enter the tank farms on a regular basis for waste retrievals, equipment maintenance, and surveillance. Tank farm contractors are in the process of retrieving all remaining waste from aging single-shell tanks, some of which date to World War II, and transferring it to newer double-shell tanks. During the waste retrieval process, tank farm workers are potentially exposed to fugitive chemical vapors that can escape from tank headspaces and other emission points. The tanks are known to hold more than 1,500 different species of chemicals, in addition to radionuclides. Exposure assessments have fully characterized the hazards from chemical vapors in half of the tank farms. Extensive sampling and analysis has been done to characterize the chemical properties of hazardous waste and to evaluate potential health hazards of vapors at the ground surface, where workers perform maintenance and waste transfer activities. Worker concerns. risk communication, and exposure assessment are discussed, including evaluation of the potential hazards of complex mixtures of chemical vapors. Concentrations of vapors above occupational exposure limits-(OEL) were detected only at exhaust stacks and passive breather filter outlets. Beyond five feet from the sources, vapors disperse rapidly. No vapors have been measured above 50% of their OELs more than five feet from the source. Vapor controls are focused on limited hazard zones around sources. Further evaluations of vapors include analysis of routes of exposure and thorough analysis of nuisance odors

Vapor and gas sampling of single-shell tank 241-B-102 using the in situ vapor sampling system

International Nuclear Information System (INIS)

Lockrem, L.L.

1997-01-01

The Vapor Issue Resolution Program tasked the Vapor Team (the team) to collect representative headspace samples from Hanford Site single-shell tank (SST) 241-B-102. This document presents sampling data resulting from the April 18, 1996 sampling of SST 241-B-102. Analytical results will be presented in a separate report issued by Pacific Northwest National Laboratory (PNNL), which supplied and analyzed the sampling media. The team, consisting of Sampling and Mobile Laboratories (SML) and Special Analytical Studies (SAS) personnel, used the vapor sampling system (VSS) to collect representative samples of the air, gases, and vapors from the headspace of SST 241-B-102 with sorbent traps and SUMMA canisters

Analyses on Water Vapor Resource in Chengdu City

Science.gov (United States)

Liu, B.; Xiao, T.; Wang, C.; Chen, D.

2017-12-01

Chengdu is located in the Sichuan basin, and it is the most famous inland city in China. With suitable temperatures and rainfall, Chengdu is the most livable cities in China. With the development of urban economy and society, the population has now risen to 16 million, and it will up to 22 million in 2030. This will cause the city water resources demand, and the carrying capacity of water resources become more and more serious. In order to improve the contradiction between urban waterlogging and water shortage, sponge city planning was proposed by Chengdu government, and this is of great practical significance for promoting the healthy development of the city. Base on the reanalysis data from NCEP during 2007-2016, the characters of Water Vapor Resources was analyzed, and the main contents of this research are summarized as follows: The water vapor resource in Chengdu plain is more than that in Southeast China and less in Northwest China. The annual average water vapor resource is approximately 160 mm -320 mm, and the water vapor resource in summer can reach 3 times in winter. But the annual average precipitation in Chengdu is about 800 mm -1200 mm and it is far greater than the water vapor resource, this is because of the transport of water vapor. Using the formula of water vapor flux, the water vapor in Chengdu is comes from the west and the south, and the value is around 50kg/(ms). Base on the calculation of boundary vapor budget, the water vapor transport under 500hPa accounted for 97% of the total. Consider the water vapor transport, transformation and urban humidification effect, the Water Vapor Resource in Chengdu is 2500mm, and it can be used by artificial precipitation enhancement. Therefore, coordinated development of weather modification and sponge city construction, the shortage of water resources in Chengdu plain can be solved. Key words: Chengdu; Sponge city; Water vapor resource; Precipitation; Artificial precipitation enhancement Acknowledgements

A technique to depress desflurane vapor pressure.

Science.gov (United States)

Brosnan, Robert J; Pypendop, Bruno H

2006-09-01

To determine whether the vapor pressure of desflurane could be decreased by using a solvent to reduce the anesthetic molar fraction in a solution (Raoult's Law). We hypothesized that such an anesthetic mixture could produce anesthesia using a nonprecision vaporizer instead of an agent-specific, electronically controlled, temperature and pressure compensated vaporizer currently required for desflurane administration. One healthy adult female dog. Propylene glycol was used as a solvent for desflurane, and the physical characteristics of this mixture were evaluated at various molar concentrations and temperatures. Using a circle system with a breathing bag attached at the patient end and a mechanical ventilator to simulate respiration, an in-circuit, nonprecision vaporizer containing 40% desflurane and 60% propylene glycol achieved an 11.5% +/- 1.0% circuit desflurane concentration with a 5.2 +/- 0.4 (0 = off, 10 = maximum) vaporizer setting. This experiment was repeated with a dog attached to the breathing circuit under spontaneous ventilation with a fresh gas flow of 0.5 L minute(-1). Anesthesia was maintained for over 2 hours at a mean vaporizer setting of 6.2 +/- 0.4, yielding mean inspired and end-tidal desflurane concentrations of 8.7% +/- 0.5% and 7.9% +/- 0.7%, respectively. Rather than alter physical properties of vaporizers to suit a particular anesthetic agent, this study demonstrates that it is also possible to alter physical properties of anesthetic agents to suit a particular vaporizer. However, propylene glycol may not prove an ideal solvent for desflurane because of its instability in solution and substantial-positive deviation from Raoult's Law.

Perspective: Highly stable vapor-deposited glasses

Science.gov (United States)

Ediger, M. D.

2017-12-01

This article describes recent progress in understanding highly stable glasses prepared by physical vapor deposition and provides perspective on further research directions for the field. For a given molecule, vapor-deposited glasses can have higher density and lower enthalpy than any glass that can be prepared by the more traditional route of cooling a liquid, and such glasses also exhibit greatly enhanced kinetic stability. Because vapor-deposited glasses can approach the bottom of the amorphous part of the potential energy landscape, they provide insights into the properties expected for the "ideal glass." Connections between vapor-deposited glasses, liquid-cooled glasses, and deeply supercooled liquids are explored. The generality of stable glass formation for organic molecules is discussed along with the prospects for stable glasses of other types of materials.

El secreto del huevo azul, de Catalina González Vilar. Estudio narratológico

Directory of Open Access Journals (Sweden)

Miguel Sánchez-García

2013-01-01

Full Text Available Este trabajo aborda el estudio narratológico de la obra El secreto del huevo azul , de la escritora Catalina González Vilar, que obtuvo el Premio El Barco de Vapor en el año 2012. Examina los diferentes elementos constitutivos del texto (el enfoque del tema, la caracterización de los personajes, la estructura sintáctica, el tratamiento del lenguaje, la técnica narrativa utilizada... y su aporte al desarrollo de la historia con la finalidad de descubrir los valores estéticos y literarios que aporta a la fábula. Pretende demostrar el adecuado uso de todos ellos dado que favorecen un texto rico en matices, llamativo, sugerente. Cualidades, todas ellas, de gran importancia tanto en creaciones destinadas al público adulto como al infantil y juvenil pues enriquece el valor final de la obra, y por extensión, el bagaje cultural de sus lectores.

Bionanomaterials and Bioinspired Nanostructures for Selective Vapor Sensing

Science.gov (United States)

2013-04-03

agricultural crops. To meet the requirements for these and other demanding applications, new sensing approaches with improved sensor selectivity are required...of these vapors with key side- chain amino acids. DNT-binding peptide receptors were further conjugated to an oligo(ethylene glycol) hydrogel for vapor...coefficient for DNT over TNT vapor. Vapor-phase binding performance was attributed to the ability of the oligo(ethylene glycol) hydrogel to maintain the

Vapor and gas sampling of single-shell tank 241-U-104 using the in situ vapor sampling system

International Nuclear Information System (INIS)

Lockrem, L.L.

1997-01-01

The Vapor Issue.Resolution Program tasked the Vapor Team (VT) to collect representative headspace samples from Hanford Site single-shell tank (SST) 241-U-104. This document presents In Situ Vapor Sampling System (ISVS) data resulting from the July 16, 1996 sampling of SST 241-U-104. Analytical results will be presented in separate reports issued by the Pacific Northwest National Laboratory (PNNL) which supplied and analyzed the sample media

Vapor and gas sampling of single-shell tank 241-S-103 using the in situ vapor sampling system

International Nuclear Information System (INIS)

Lockrem, L.L.

1997-01-01

The Vapor Issue Resolution Program tasked the Vapor Team (VT) to collect representative headspace samples from Hanford Site single-shell tank (SST) 241-S-103. This document presents In Situ Vapor Sampling System (ISVS) data resulting from the June 12, 1996 sampling of SST 241-S-103. Analytical results will be presented in separate reports issued by the Pacific Northwest National Laboratory (PNNL) which supplied and analyzed the sample media

Vapor and gas sampling of single-shell tank 241-S-106 using the in situ vapor sampling system

International Nuclear Information System (INIS)

Lockrem, L.L.

1997-01-01

The Vapor Issue Resolution Program tasked the Vapor Team (VT) to collect representative headspace samples from Hanford Site single-shell tank (SST) 241-S-106. This document presents In Situ vapor Sampling System (ISVS) data resulting from the June 13, 1996 sampling of SST 241-S-106. Analytical results will be presented in separate reports issued by the Pacific Northwest National Laboratory (PNNL) which'supplied and analyzed the sample media

Energy advantage of the cane bagasse in the sugar industry; Aprovechamiento energetico del bagazo de cana en la industria azucarera

Energy Technology Data Exchange (ETDEWEB)

Hernandez Alarcon, Luis Alfredo

1987-07-01

. [Spanish] El presente estudio hace un analisis de la produccion y consumo de bagazo en Mexico relacionada con aquellos indicadores que orientan y afectan el aprovechamiento energetico de la fibra dentro de la estructura y balance global de energeticos del subsector azucar. Este analisis global se concentra al final sobre la evaluacion de los generadores de vapor de un ingenio azucarero, que como Casasano, paso de quemar solo combustoleo hasta 1984, a usar a la vez bagazo y combustoleo, en un intento por reducir su consumo especifico de energia, uno de los mas altos del pais. En 1985 se cultivaron 534 mil hectareas de cana, con rendimientos de campo de 68.8 t/ha; de los 36.7 millones de toneladas de cana producidas se molieron 35.7 millones para obtener, en los 69 ingenios del pais 3.2 millones de toneladas de azucar, satisfaciendo nuevamente el consumo nacional. En la respectiva zafra se produjeron 12 millones de toneladas de bagazo humedo, representando el 34.5% del total de la cana molida; este bagazo se destino en un 86.5% a la generacion de vapor, con un indice medio de 1.87 kg de vapor por kg de bagazo, aportando al balance energetico propio el equivalente a 17.6 billones de kilocalorias que corresponden al 66.2% de la energia total consumida por el sector, siendo el restante 33.8% aportado por el combustoleo. Para generar vapor en 1985 habia instalados 543859 HP aprovechados con una eficiencia ponderada del 56.4%, de los cuales el 91.5% utilizaba en forma simultanea bagazo y combustoleo, el 6.38% solo combustoleo y el 2.1% solo bagazo. En el ingenio Casasano se hace un analisis similar, rematando con la evaluacion del aprovechamiento energetico del bagazo en sus calderas y de los factores que influyen en el consumo especifico de energia. De esta forma se establece que el bagazo consumido en la ultima zafra se quemo generando 1.4 kg de vapor por kg de bagazo en calderas trabajando con una eficiencia del 60% y consumiendo 1090 kg de vapor por tonelada de cana molida.

Cumulus convection and the terrestrial water-vapor distribution

Science.gov (United States)

Donner, Leo J.

1988-01-01

Cumulus convection plays a significant role in determining the structure of the terrestrial water vapor field. Cumulus convection acts directly on the moisture field by condensing and precipitating water vapor and by redistributing water vapor through cumulus induced eddy circulations. The mechanisms by which cumulus convection influences the terrestrial water vapor distribution is outlined. Calculations using a theory due to Kuo is used to illustrate the mechanisms by which cumulus convection works. Understanding of these processes greatly aids the ability of researchers to interpret the seasonal and spatial distribution of atmospheric water vapor by providing information on the nature of sources and sinks and the global circulation.

Vapor pumps and gas-driven machines

International Nuclear Information System (INIS)

Guillet, R.

1991-01-01

The vapor pump, patented in 1979 by Gaz de France, is an additional mass and heat exchanger which uses the combustion air of fuel-burning machines as an additional cold source. This cold source is preheated and, above all, humidified before reaching the burner, by means of the residual sensible and latent heat in the combustion products of the fuel-burning process. This final exchanger thus makes it possible, in many cases, to recover all the gross calorific value of natural gas, even when the combustion products leave the process at a wet temperature greater than 60 0 C, the maximum dew point of the products of normal combustion. Another significant advantage of the vapor pump being worth highlighting is the selective recycling of water vapor by the vapor pump which reduces the adiabatic combustion temperature and the oxygen concentration in the combustion air, two factors which lead to considerable reductions in nitrogen oxides formation, hence limiting atmospheric pollution. Alongside a wide range of configurations which make advantageous use of the vapor pump in association with gas-driven machines and processes, including gas turbines, a number of boiler plant installations are also presented [fr

Thermodynamics and Kinetics of Silicate Vaporization

Science.gov (United States)

Jacobson, Nathan S.; Costa, Gustavo C. C.

2015-01-01

Silicates are a common class of materials that are often exposed to high temperatures. The behavior of these materials needs to be understood for applications as high temperature coatings in material science as well as the constituents of lava for geological considerations. The vaporization behavior of these materials is an important aspect of their high temperature behavior and it also provides fundamental thermodynamic data. The application of Knudsen effusion mass spectrometry (KEMS) to silicates is discussed. There are several special considerations for silicates. The first is selection of an appropriate cell material, which is either nearly inert or has well-understood interactions with the silicate. The second consideration is proper measurement of the low vapor pressures. This can be circumvented by using a reducing agent to boost the vapor pressure without changing the solid composition or by working at very high temperatures. The third consideration deals with kinetic barriers to vaporization. The measurement of these barriers, as encompassed in a vaporization coefficient, is discussed. Current measured data of rare earth silicates for high temperature coating applications are discussed. In addition, data on magnesium-iron-silicates (olivine) are presented and discussed.

Modeling UTLS water vapor: Transport/Chemistry interactions

International Nuclear Information System (INIS)

Gulstad, Line

2005-01-01

This thesis was initially meant to be a study on the impact on chemistry and climate from UTLS water vapor. However, the complexity of the UTLS water vapor and its recent changes turned out to be a challenge by it self. In the light of this, the overall motivation for the thesis became to study the processes controlling UTLS water vapor and its changes. Water vapor is the most important greenhouse gas, involved in important climate feedback loops. Thus, a good understanding of the chemical and dynamical behavior of water vapor in the atmosphere is crucial for understanding the climate changes in the last century. Additionally, parts of the work was motivated by the development of a coupled climate chemistry model based on the CAM3 model coupled with the Chemical Transport Model Oslo CTM2. The future work will be concentrated on the UTLS water vapor impact on chemistry and climate. We are currently studying long term trends in UTLS water vapor, focusing on identification of the different processes involved in the determination of such trends. The study is based on natural as well as anthropogenic climate forcings. The ongoing work on the development of a coupled climate chemistry model will continue within our group, in collaboration with Prof. Wei-Chyung Wang at the State University of New York, Albany. Valuable contacts with observational groups are established during the work on this thesis. These collaborations will be continued focusing on continuous model validation, as well as identification of trends and new features in UTLS water vapor, and other tracers in this region. (Author)

Calculating the enthalpy of vaporization for ionic liquid clusters.

Science.gov (United States)

Kelkar, Manish S; Maginn, Edward J

2007-08-16

Classical atomistic simulations are used to compute the enthalpy of vaporization of a series of ionic liquids composed of 1-alkyl-3-methylimidazolium cations paired with the bis(trifluoromethylsulfonyl)imide anion. The calculations show that the enthalpy of vaporization is lowest for neutral ion pairs. The enthalpy of vaporization increases by about 40 kJ/mol with the addition of each ion pair to the vaporizing cluster. Non-neutral clusters have much higher vaporization enthalpies than their neutral counterparts and thus are not expected to make up a significant fraction of volatile species. The enthalpy of vaporization increases slightly as the cation alkyl chain length increases and as temperature decreases. The calculated vaporization enthalpies are consistent with two sets of recent experimental measurements as well as with previous atomistic simulations.

Generación directa de vapor con colectores solares cilindro parabólicos Proyecto DIrect Solar Steam (DISS)

OpenAIRE

Zarza Moya, Eduardo

2003-01-01

La Generación Directa de Vapor (GDV) en los tubos absorbedores de los colectores solares cilindro parabólicos es considerada la opción tecnológica más atractiva para conseguir una sustancial reducción del coste de la energía térmica producida por este tipo de colector solar. Sin embargo, antes de poder comercializar sistemas solares con GDV e s necesario aclarar todas aquellas cuestiones técnicas que conlleva la existencia de un flujo bifásico circulando por el interior de los tubos absorbedo...

Prediction of vapor pressure and heats of vaporization of edible oil/fat compounds by group contribution

DEFF Research Database (Denmark)

Ceriani, Roberta; Gani, Rafiqul; Liu, Y.A.

2013-01-01

In the present work, a group contribution method is proposed for the estimation of vapor pressures and heats of vaporization of organic liquids found in edible fat/oil and biofuel industries as a function of temperature. The regression of group contribution parameters was based on an extensive...

Comparative study of the vapor analytes of trinitrotoluene (TNT)

Science.gov (United States)

Edge, Cindy C.; Gibb, Julie; Dugan, Regina E.

1998-12-01

Trinitrotoluene (TNT) is a high explosive used in most antipersonnel and antitank landmines. The Institute for Biological Detection Systems (IBDS) has developed a quantitative vapor delivery system, termed olfactometer, for conducting canine olfactory research. The research is conducted utilizing dynamic conditions, therefore, it is imperative to evaluate the headspace of TNT to ensure consistency with the dynamic generation of vapor. This study quantified the vapor headspace of military- grade TNT utilizing two different vapor generated methodologies, static and dynamic, reflecting differences between field and laboratory environments. Static vapor collection, which closely mimics conditions found during field detection, is defined as vapor collected in an open-air environment at ambient temperature. Dynamic vapor collection incorporates trapping of gases from a high flow vapor generation cell used during olfactometer operation. Analysis of samples collected by the two methodologies was performed by gas chromatography/mass spectrometry and the results provided information with regard to the constituents detected. However, constituent concentration did vary between the sampling methods. This study provides essential information regarding the vapor constituents associated with the TNT sampled using different sampling methods. These differences may be important in determining the detection signature dogs use to recognize TNT.

Thermal analysis of the heat recuperator of a combined cycle thermoelectric central; Analisis termico del recuperador de calor de una central termoelectrica de ciclo combinado

Energy Technology Data Exchange (ETDEWEB)

Romero Paredes, Hernando; Sanchez, I; Lazcano, L C; Ambriz, Juan Jose; Alvarez, M [Universidad Autonoma Metropolitana-Iztapalapa, Mexico, D. F. (Mexico); Gonzalez, O [Comision Federal de Electricidad, Tula (Mexico)

1997-12-31

The thermoelectric centrals of the combined cycle type (Brayton Cycle and Rankine Cycle) present a series of opportunities to increase the efficiency of the combined cycle or of the generated power. This paper shows the methodology for the performance of energy balances in a heat recuperator (H. R.), typically employed in the combined cycle stations operating in Mexico, for the assessment of the energy harnessing in the different sections conforming a H. R. The effect of the installation of evaporative coolers and/or an absorption cooling system at the gas turbine compressor intake on the steam generation in the heat recuperator, is evaluated. This extra generation of steam is quantified for its potential use in the same absorption refrigeration system. From the assessment, it follows up that the steam generation in the H.R. is inversely proportional to the ambient temperature and that, although the increased amount of steam generated can not be harnessed in total by the steam turbine, the remaining fraction is good enough to cover the heat demand for the operation of the refrigeration system. [Espanol] Las centrales termoelectricas del tipo ciclo combinado (ciclo Brayton y ciclo Rankine) presentan un conjunto de oportunidades para incrementar la eficiencia del ciclo combinado o bien la potencia generada. En el presente trabajo se expone la metodologia para realizar los balances de energia en un recuperador de calor (R.C.) tipicamente utilizado en las Centrales de Ciclo Combinado (CCC) que operan en Mexico, para evaluar el aprovechamiento de la energia en las diferentes secciones que conforman un R.C. Se evalua el efecto que tiene la instalacion de enfriadores evaporativos y/o un sistema de enfriamiento por absorcion en la succion del compresor de la turbina de gas sobre la generacion de vapor en el recuperador de calor. Se cuantifica esta generacion extra de vapor para su posible utilizacion en el mismo sistema de refrigeracion por absorcion. De la evaluacion se

Thermal analysis of the heat recuperator of a combined cycle thermoelectric central; Analisis termico del recuperador de calor de una central termoelectrica de ciclo combinado

Energy Technology Data Exchange (ETDEWEB)

Romero Paredes, Hernando; Sanchez, I.; Lazcano, L. C.; Ambriz, Juan Jose; Alvarez, M. [Universidad Autonoma Metropolitana-Iztapalapa, Mexico, D. F. (Mexico); Gonzalez, O. [Comision Federal de Electricidad, Tula (Mexico)

1996-12-31

The thermoelectric centrals of the combined cycle type (Brayton Cycle and Rankine Cycle) present a series of opportunities to increase the efficiency of the combined cycle or of the generated power. This paper shows the methodology for the performance of energy balances in a heat recuperator (H. R.), typically employed in the combined cycle stations operating in Mexico, for the assessment of the energy harnessing in the different sections conforming a H. R. The effect of the installation of evaporative coolers and/or an absorption cooling system at the gas turbine compressor intake on the steam generation in the heat recuperator, is evaluated. This extra generation of steam is quantified for its potential use in the same absorption refrigeration system. From the assessment, it follows up that the steam generation in the H.R. is inversely proportional to the ambient temperature and that, although the increased amount of steam generated can not be harnessed in total by the steam turbine, the remaining fraction is good enough to cover the heat demand for the operation of the refrigeration system. [Espanol] Las centrales termoelectricas del tipo ciclo combinado (ciclo Brayton y ciclo Rankine) presentan un conjunto de oportunidades para incrementar la eficiencia del ciclo combinado o bien la potencia generada. En el presente trabajo se expone la metodologia para realizar los balances de energia en un recuperador de calor (R.C.) tipicamente utilizado en las Centrales de Ciclo Combinado (CCC) que operan en Mexico, para evaluar el aprovechamiento de la energia en las diferentes secciones que conforman un R.C. Se evalua el efecto que tiene la instalacion de enfriadores evaporativos y/o un sistema de enfriamiento por absorcion en la succion del compresor de la turbina de gas sobre la generacion de vapor en el recuperador de calor. Se cuantifica esta generacion extra de vapor para su posible utilizacion en el mismo sistema de refrigeracion por absorcion. De la evaluacion se

Impact of groundwater levels on evaporation and water-vapor fluxes in highly saline soils

Science.gov (United States)

Munoz, J. F.; Hernández, M. F.; Braud, I.; Gironas, J. A.; Suarez, F. I.

2012-12-01

In aquifers of arid and hyper-arid zones, such as those occurring in the Chilean Andes high plateau, it is important to determine both the quantity and location of water discharges at the temporal scales of interest to close the basin's water budget and thus, to manage the water resource properly. In zones where shallow aquifers are the main source of water, overexploitation of the water resource changes the dynamics of water, heat and solute transport in the vadose zone. As aquifers are exploited, fluctuations in depth to groundwater are exacerbated. These fluctuations modify both soil structure and evaporation from the ground, which is typically the most important discharge from the water budget and is very difficult to estimate. Therefore, a correct quantification of evaporation from these soils is essential to improve the accuracy of the water balance estimation. The objective of this study was to investigate the evaporation processes and water-vapor fluxes in a soil column filled with a saline soil from the Salar del Huasco basin, Chile. Water content, electrical conductivity and temperature at different depths in the soil profile were monitored to determine the liquid and vapor fluxes within the soil column. The results showed that evaporation is negligible when the groundwater table is deeper than 1 m. For shallower groundwater levels, evaporation increases in an exponential fashion reaching a value of 3 mm/day when the groundwater table is near the surface of the ground. These evaporation rates are on the same order of magnitude than the field measurements, but slightly lower due to the controlled conditions maintained in the laboratory. Isothermal fluid fluxes were predominant over the non-isothermal fluid and water vapor fluxes. The net flux for all the phreatic levels tested in the laboratory showed different behaviors, with ascending or descending flows as a consequence of changes in water content and temperature distribution within the soil. It was

Development and evaluation of the NSSS model with four steam lines for the LVNP using the SCDAPSIM code; Desarrollo y evaluacion del modelo del NSSS con cuatro lineas de vapor para la CNLV utilizando el codigo SCDAPSIM

Energy Technology Data Exchange (ETDEWEB)

Salazar C, J.H.; Nunez C, A.; Camargo C, R. [CNSNS, Dr. Barragan No. 779, Col. Narvarte, 03020 Mexico D.F. (Mexico)

2005-07-01

The present work shows the pattern of the NSSS considering the four main vapor lines as well as their evaluation. The pattern was developed by the National Commission of Nuclear Security and Safeguards (CNSNS) and it has as main objective to account with a model of the Laguna Verde Nuclear power plant (CNLV) for the simulation and analysis of transitory events where are involved some of main vapor lines, or some relief valves and safety (SRV's). The model was evaluated with data of the CNLV. In 1996 the Federal Commission of Electricity (CFE) request to the CNSNS permission to operate the Unit 2 until the first recharge, having the main vapor line 'B' isolated and operating with a level of power corresponding to a flow of total vapor of 85% of the nominal one (of 1931 MWt). The obtained values were compared with the obtained registrations of the CNLV in order to evaluate the model. Those results show relative errors inferior to 3% among the CNLV reported value and the one calculated by the SCDAPSIM code. (Author)

Evaluation of the useful life of steam turbine rotors; Evaluacion de vida util de rotores de turbinas de vapor

Energy Technology Data Exchange (ETDEWEB)

Carnero Parra, Antonio; Garcia Illescas, Rafael; Kubiak Szyszka, Janusz [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

1999-07-01

This article presents the methodology applied by the Management of Turbomachinery of the Institute of Investigaciones Electricas (IIE), for the evaluation of the remaining useful life of steam turbine rotors in the phase of initiation of fissures. The evaluation of the remaining useful life of turbines, will reveal the real state of health of the rotor and will serve as a base for the future decision making that guarantees their structural integrity. [Spanish] El presentes articulo presenta la metodologia aplicada por la Gerencia de Turbomaquinaria del Instituto de Investigaciones Electricas (IIE), para la evaluacion de la vida util remanente de rotores de turbinas de vapor en la fase de iniciacion de fisuras. La evaluacion de la vida util de turbinas, revelar el estado real de salud del rotor y servira de base para la toma de decisiones futuras que garanticen su integridad estructural.

Estimating enthalpy of vaporization from vapor pressure using Trouton's rule.

Science.gov (United States)

MacLeod, Matthew; Scheringer, Martin; Hungerbühler, Konrad

2007-04-15

The enthalpy of vaporization of liquids and subcooled liquids at 298 K (delta H(VAP)) is an important parameter in environmental fate assessments that consider spatial and temporal variability in environmental conditions. It has been shown that delta H(VAP)P for non-hydrogen-bonding substances can be estimated from vapor pressure at 298 K (P(L)) using an empirically derived linear relationship. Here, we demonstrate that the relationship between delta H(VAP)and PL is consistent with Trouton's rule and the ClausiusClapeyron equation under the assumption that delta H(VAP) is linearly dependent on temperature between 298 K and the boiling point temperature. Our interpretation based on Trouton's rule substantiates the empirical relationship between delta H(VAP) degree and P(L) degrees for non-hydrogen-bonding chemicals with subcooled liquid vapor pressures ranging over 15 orders of magnitude. We apply the relationship between delta H(VAP) degrees and P(L) degrees to evaluate data reported in literature reviews for several important classes of semivolatile environmental contaminants, including polycyclic aromatic hydrocarbons, chlorobenzenes, polychlorinated biphenyls and polychlorinated dibenzo-dioxins and -furans and illustrate the temperature dependence of results from a multimedia model presented as a partitioning map. The uncertainty associated with estimating delta H(VAP)degrees from P(L) degrees using this relationship is acceptable for most environmental fate modeling of non-hydrogen-bonding semivolatile organic chemicals.

Recommended Vapor Pressure of Solid Naphthalen

Czech Academy of Sciences Publication Activity Database

Růžička, K.; Fulem, Michal; Růžička, V.

2005-01-01

Roč. 50, - (2005), s. 1956-1970 ISSN 0021-9568 Institutional research plan: CEZ:AV0Z10100521 Keywords : solid naphthalene * vapor pressure * enthalpy of vaporization * enthalpy of fusion Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.610, year: 2005

SOIL VAPOR EXTRACTION TECHNOLOGY: REFERENCE HANDBOOK

Science.gov (United States)

Soil vapor extraction (SVE) systems are being used in Increasing numbers because of the many advantages these systems hold over other soil treatment technologies. SVE systems appear to be simple in design and operation, yet the fundamentals governing subsurface vapor transport ar...

Bionanomaterials and Bioinspired Nanostructures for Selective Vapor Sensing

Science.gov (United States)

Potyrailo, Radislav; Naik, Rajesh R.

2013-07-01

At present, monitoring of air at the workplace, in urban environments, and on battlefields; exhaled air from medical patients; air in packaged food containers; and so forth can be accomplished with different types of analytical instruments. Vapor sensors have their niche in these measurements when an unobtrusive, low-power, and cost-sensitive technical solution is required. Unfortunately, existing vapor sensors often degrade their vapor-quantitation accuracy in the presence of high levels of interferences and cannot quantitate several components in complex gas mixtures. Thus, new sensing approaches with improved sensor selectivity are required. This technological task can be accomplished by the careful design of sensing materials with new performance properties and by coupling these materials with the suitable physical transducers. This review is focused on the assessment of the capabilities of bionanomaterials and bioinspired nanostructures for selective vapor sensing. We demonstrate that these sensing materials can operate with diverse transducers based on electrical, mechanical, and optical readout principles and can provide vapor-response selectivity previously unattainable by using other sensing materials. This ability for selective vapor sensing provides opportunities to significantly impact the major directions in development and application scenarios of vapor sensors.

Research and technological development on heat pumps in Mexico operating with geothermal energy; Investigacion y desarrollo tecnologico sobre bombas de calor en Mexico operando con energia geotermica

Energy Technology Data Exchange (ETDEWEB)

Garcia Gutierrez, Alfonso; Barragan Reyes, Rosa Maria; Arellano Gomez, Victor Manuel [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2008-07-01

The Instituto de Investigaciones Electricas (IIE) and the Comision Federal de Electricidad (CFE) carried out in the past an extensive work of research and development (R&D) on heat pumps (HP). The systems tried on include heat pumps by mechanical compression, thermal absorption and thermal transformers. This paper briefly describes the main aspects of R&D on heat pumps and presents a more detailed description of three of the main studies: a) a Heat Pump (HP) by mechanical compression water-water type, designed for brine purification, operating with low pressure geothermal steam at the geothermal field Los Azufres, Michoacan, Mexico; b) a HP by absorption for cooling and refrigeration, operating with ammoniac/water and low enthalpy geothermal energy, which was tested in the geothermal fields of Los Azufres, Michoacan and Cerro Prieto, Baja California, and c) a thermal transformer by absorption, named Heat Pump by Absorption Type 2, which was tested to evaluate the behavior of diverse ternary solutions as working fluids. To date, there are plans to install and test a geothermal heat pump (connected to the subsoil), in Cerro Prieto, Mexicali, Baja California, Mexico. [Spanish] El Instituto de Investigaciones Electricas (IIE) y la Comision Federal de Electricidad (CFE) realizaron un trabajo extenso de investigacion y desarrollo (I&D) sobre bombas de calor (BC) en el pasado. Los sistemas que se probaron incluyen bombas de calor por compresion mecanica, absorcion y transformadores termicos. Este trabajo describe brevemente los principales aspectos de I&D sobre bombas de calor y se da una descripcion mas detallada de tres de los principales estudios: a) una Bomba de Calor (BC) por compresion mecanica tipo agua-agua, disenada para purificacion de salmueras, operando con vapor geotermico de baja presion en el campo geotermico de Los Azufres, Michoacan; b) una BC por absorcion para enfriamiento y refrigeracion, operando con amoniaco/agua y energia geotermica de baja entalpia

Decreased respiratory symptoms in cannabis users who vaporize

Directory of Open Access Journals (Sweden)

Barnwell Sara

2007-04-01

Full Text Available Abstract Cannabis smoking can create respiratory problems. Vaporizers heat cannabis to release active cannabinoids, but remain cool enough to avoid the smoke and toxins associated with combustion. Vaporized cannabis should create fewer respiratory symptoms than smoked cannabis. We examined self-reported respiratory symptoms in participants who ranged in cigarette and cannabis use. Data from a large Internet sample revealed that the use of a vaporizer predicted fewer respiratory symptoms even when age, sex, cigarette smoking, and amount of cannabis used were taken into account. Age, sex, cigarettes, and amount of cannabis also had significant effects. The number of cigarettes smoked and amount of cannabis used interacted to create worse respiratory problems. A significant interaction revealed that the impact of a vaporizer was larger as the amount of cannabis used increased. These data suggest that the safety of cannabis can increase with the use of a vaporizer. Regular users of joints, blunts, pipes, and water pipes might decrease respiratory symptoms by switching to a vaporizer

A Local Propagation for Vapor Explosions

International Nuclear Information System (INIS)

Ochiai, M.; Bankoff, S.G.

1976-01-01

Explosive boiling, defined as energy transfer leading to formation of vapor rapidly enough to produce large shock waves, has been widely studied in a number of contexts. Depending upon the nature and temperatures of the liquids and mode of contacting, large-scale mixing and explosive vaporization may occur, or alternatively, only relatively non-energetic, film-type boiling may exist. The key difference is whether a mechanism is operative for increasing the liquid-liquid interfacial area in a time scale consistent with the formation of a detonation wave. Small drops of a cold volatile liquid were dropped onto a free surface of a hot, non-volatile liquid. The critical Weber number for coalescence is obtained from the envelope of the film boiling region. Markedly different behavior for the two hot liquids is observed. A 'splash' theory for local propagation of vapor explosions in spontaneously nucleating liquid-liquid systems is now formulated. After a random contact is made, explosive growth and coalescence of the vapor bubbles occurs as soon as the surrounding pressure is relieved, resulting in a high-pressure vapor layer at the liquid-liquid contact area. This amounts to an impact pressure applied to the free surface, with a resulting velocity distribution obtained from potential flow theory. The peak pressure predictions are. consistent with data for Freon-oil mixing, but further evaluation will await additional experimental data. Nevertheless, the current inference is that a UO 2 -Na vapor explosion in a reactor environment cannot be visualized. In conclusion: The propagation model presented here differs in some details from that of Henry and Fauske, although both are consistent with some peak pressure data obtained by Henry, et al. Clearly, additional experimental information is needed for further evaluation of these theories. Nevertheless, it should be emphasized that even at this time a number of important observations concerning the requirements for a vapor

Optical Sensor for Diverse Organic Vapors at ppm Concentration Ranges

Directory of Open Access Journals (Sweden)

Dora M. Paolucci

2011-03-01

Full Text Available A broadly responsive optical organic vapor sensor is described that responds to low concentrations of organic vapors without significant interference from water vapor. Responses to several classes of organic vapors are highlighted, and trends within classes are presented. The relationship between molecular properties (vapor pressure, boiling point, polarizability, and refractive index and sensor response are discussed.

CÁLCULO DE LOS ÍNDICES DE CONSUMO DE VAPOR EN LA PLANTA DE LLENADO, LIOFILIZACIÓN Y ENVASE Y OTROS SERVICIOS DEL CENTRO NACIONAL DE BIOPREPARADOS

Directory of Open Access Journals (Sweden)

Marta Domingo Montané

2011-02-01

Full Text Available El progresivo encarecimiento de los productos y servicios energéticos se ha convertido en una preocupaciónprioritaria para toda industria, es por ello que en esta política nacional de ahorro y conservaciónde portadores energéticos se realiza este trabajo en la Planta de Llenado, Liofilización y Envasey en las áreas de Lavandería y Cocina- Comedor, pertenecientes al Centro Nacional deBiopreparados, con el objetivo de determinar los índices de consumo de vapor en los procesosproductivos. Se realizaron varias corridas con el fin de obtener los consumos de vapor directamentede la práctica o de cálculos, a partir de balances de energía y correlaciones de transferencia de calor.Se calcula también el consumo de vapor dado por las pérdidas al medio ambiente en las tuberías quelo transportan a los puntos de consumo. Se obtuvieron los índices de consumo en cada área de vapor,de combustible y económicos correspondientes. Se recomienda al Centro utilizar los índices deconsumo calculados para la comprobación de la eficiencia energética de las áreas estudiadas.  The progressive rise in the price of the products and energy services have become a high-priorityconcern for all industry, it is for it that in this national politics of saving and energy portersconservation is carried out this work, in the Plant of having Filled, Liofilization and packing;and in the areas of Laundry and Kitchen - dining room, belonging to the Centro Nacional deBiopreparados with the objective of determining the indexes of consumption of vapor in theproductive processes. They were carried out several experiments, with the purpose of obtainingthe consumptions of vapor directly of the practice or of calculations, starting from energy balancesand correlations of heat transfer . The consumption of vapor given by the losses to theenvironment in the pipes, that transports it to the consumption points is also calculated. Theconsumption indexes were obtained in each

40 CFR 52.787 - Gasoline transfer vapor control.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Gasoline transfer vapor control. 52.787... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Indiana § 52.787 Gasoline transfer vapor control. (a) Gasoline means any petroleum distillate having a Reid vapor pressure of 4 pounds or greater...

Estimating evaporative vapor generation from automobiles based on parking activities

International Nuclear Information System (INIS)

Dong, Xinyi; Tschantz, Michael; Fu, Joshua S.

2015-01-01

A new approach is proposed to quantify the evaporative vapor generation based on real parking activity data. As compared to the existing methods, two improvements are applied in this new approach to reduce the uncertainties: First, evaporative vapor generation from diurnal parking events is usually calculated based on estimated average parking duration for the whole fleet, while in this study, vapor generation rate is calculated based on parking activities distribution. Second, rather than using the daily temperature gradient, this study uses hourly temperature observations to derive the hourly incremental vapor generation rates. The parking distribution and hourly incremental vapor generation rates are then adopted with Wade–Reddy's equation to estimate the weighted average evaporative generation. We find that hourly incremental rates can better describe the temporal variations of vapor generation, and the weighted vapor generation rate is 5–8% less than calculation without considering parking activity. - Highlights: • We applied real parking distribution data to estimate evaporative vapor generation. • We applied real hourly temperature data to estimate hourly incremental vapor generation rate. • Evaporative emission for Florence is estimated based on parking distribution and hourly rate. - A new approach is proposed to quantify the weighted evaporative vapor generation based on parking distribution with an hourly incremental vapor generation rate

Determinación del antagonismo del aislamiento T 95 de Trichoderma harzianum sobre Fusarium oxysporum f.sp. cucumerinum en plantas de pepino cohombro

Directory of Open Access Journals (Sweden)

Borda Fernando

1993-06-01

Full Text Available Una de las enfermedades de mayor importancia económica en el cultivo de clavel en Colombia es la ocasionada por el hongo Fusarium oxysporumf.sp. dianthi. Las altas pérdidas directas que ocasiona el patógeno una vez establecido en cultivos comerciales, la facilidad de propagación através de esquejes infectados, la fácil diseminación del patógeno a
través de diferentes formas, la alta persistencia del
patógeno en el suelo y el alto costo y regular eficiencia
de las medidas de control utilizadas, dan a esta
enfermedad una gran importancia patológica y económica
(Arbeláez, 1987. Para el control del marchitamiento vascular del clavel, se realizan prácticas, tales como tratamiento
del suelo con vapor deagua, con diversos fumigantes y con fungicidas sistémicos, pero el costo de dichas prácticas puede variar actualmente entre $500.000 y $10.000.000, lo cual depende del tipo de tratamiento (Baker, 1980; Arbeláez, 1989. Las dificultades encontradas en el manejo de las
poblaciones de Fusarium oxysporum f.sp. dianthi en el suelo por métodos convencionales, hacen que el control biológico sea uno de los métodos más promisorios para el control de la enfermedad; además el control biológico puede combinarse con otros métodos de control y asl, se logra una mayor
eficiencia (Scher y Baker, 1980.

Enfoque “Aprendizaje Basado en Proyectos” para enseñar sistemas de potencia de gas y vapor

Directory of Open Access Journals (Sweden)

Asier Aranzábal

2014-12-01

Full Text Available El objetivo de este trabajo es presentar la experiencia y los resultados derivados de la aplicación del método Aprendizaje Basado en Proyectos (PBL en la asignatura Termotecnia de la Titulación de Ingeniería Química de la Universidad del País Vasco/Euskal Herriko Unibertsitatea, para aprender sistemas de potencia de gas y vapor. Tras un análisis crítico de los resultados académicos de los alumnos que aprenden estos sistemas, se observa que la estrategia de enseñanza-aprendizaje tradicional, basada en clases “magistrales + clases de aplicación en una lista de ejercicios (totalmente acotados y con una solución única, estaba fallando. Ante esta situación se plantea un enfoque constructivista centrado en el alumno para que él mismo construya su aprendizaje activa y cooperativamente, y no escuchando clases magistrales, ni memorizando.

40 CFR 52.255 - Gasoline transfer vapor control.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Gasoline transfer vapor control. 52.255... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.255 Gasoline transfer vapor control. (a) “Gasoline” means any petroleum distillate having a Reid vapor pressure of 4 pounds or greater...

33 CFR 154.826 - Vapor compressors and blowers.

Science.gov (United States)

2010-07-01

...) Excessive shaft bearing temperature. (d) If a centrifugal compressor, fan, or lobe blower handles vapor in... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Vapor compressors and blowers....826 Vapor compressors and blowers. (a) Each inlet and outlet to a compressor or blower which handles...

Effect of granosan vapors on mitosis

Energy Technology Data Exchange (ETDEWEB)

Lishenko, N P; Lishenko, I D

1974-01-01

Experiments were performed to determine the effects of granosan on the germination of vetch seeds. Vetch seeds were stored from 4-6 days in ethyl mercuric chloride vapors. Results indicated that the vapors caused a sharp decrease in germination and caused chromosomal aberrations during the anaphase.

Molecular dynamics study of the vaporization of an ionic drop

Science.gov (United States)

Galamba, N.

2010-09-01

The melting of a microcrystal in vacuum and subsequent vaporization of a drop of NaCl were studied through molecular dynamics simulations with the Born-Mayer-Huggins-Tosi-Fumi rigid-ion effective potential. The vaporization was studied for a single isochor at increasing temperatures until the drop completely vaporized, and gaseous NaCl formed. Examination of the vapor composition shows that the vapor of the ionic drop and gaseous NaCl are composed of neutral species, the most abundant of which, ranging from simple NaCl monomers (ion pairs) to nonlinear polymers, (NanCln)n=2-4. The enthalpies of sublimation, vaporization, and dissociation of the different vapor species are found to be in reasonable agreement with available experimental data. The decrease of the enthalpy of vaporization of the vapor species, with the radius of the drop decrease, accounts for a larger fraction of trimers and tetramers than that inferred from experiments. Further, the rhombic dimer is significantly more abundant than its linear isomer although the latter increases with the temperature. The present results suggest that both trimers and linear dimers may be important to explain the vapor pressure of molten NaCl at temperatures above 1500 K.

21 CFR 888.4220 - Cement monomer vapor evacuator.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cement monomer vapor evacuator. 888.4220 Section... (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Surgical Devices § 888.4220 Cement monomer vapor evacuator. (a) Identification. A cement monomer vapor evacuator is a device intended for use during surgery to contain or remove...

Prediction of the vapor pressure and vaporization enthalpy of 1-n-alkyl-3-methylimidazolium-bis-(trifluoromethanesulfonyl) amide ionic liquids.

Science.gov (United States)

Diedenhofen, Michael; Klamt, Andreas; Marsh, Kenneth; Schäfer, Ansgar

2007-09-07

The vapor pressures and vaporization enthalpies of a series of 1-n-alkyl-3-methylimidazolium-bis-(trifluoromethanesulfonyl) amide ionic liquids have been predicted with two different approaches using the COSMO-RS method and quantum chemical gas phase calculations. While the calculated enthalpies are in good agreement with the experimental data, COSMO-RS seems to underestimate the vapor pressures by roughly 0.5-4 log units dependent on the IL and approach used.

40 CFR 796.1950 - Vapor pressure.

Science.gov (United States)

2010-07-01

... (CONTINUED) CHEMICAL FATE TESTING GUIDELINES Physical and Chemical Properties § 796.1950 Vapor pressure. (a.... In addition, chemicals that are likely to be gases at ambient temperatures and which have low water... gases until the measured vapor pressure is constant, a process called “degassing.” Impurities more...

Performance of horizontal versus vertical vapor extraction wells

International Nuclear Information System (INIS)

Birdsell, K.H.; Roseberg, N.D.; Edlund, K.M.

1994-06-01

Vapor extraction wells used for site remediation of volatile organic chemicals in the vadose zone are typically vertical wells. Over the past few years, there has been an increased interest in horizontal wells for environmental remediation. Despite the interest and potential benefits of horizontal wells, there has been little study of the relative performance of horizontal and vertical vapor extraction wells. This study uses numerical simulations to investigate the relative performance of horizontal versus vertical vapor extraction wells under a variety of conditions. The most significant conclusion that can be drawn from this study is that in a homogeneous medium, a single, horizontal vapor extraction well outperforms a single, vertical vapor extraction well (with surface capping) only for long, linear plumes. Guidelines are presented regarding the use of horizontal wells

Dynamics of trivalent rare earth molecular vapor lasers

International Nuclear Information System (INIS)

Krupke, W.F.

1976-01-01

Radiative transition probabilities in neodymium bearing vapors are reviewed and calculations are extended to visible laser transitions in terbium bearing vapor. Nonradiative relaxation processes in the pure and complexed halides are treated in greater detail. While precise, quantitative relaxation probabilities cannot be calculated on the basis of information presently available, plausibility arguments can be established which indicate the order of magnitude of relevant nonradiative decay probabilities. Reference to solid and liquid state nonradiative relaxation data for rare earth ions is reviewed to support the plausibility arguments for the vapor state. Having established the likelihood of high fluorescence yields in the vapor phase, various methods of laser pumping are discussed: optical pumping via parity allowed 4f-5d transitions; optical pumping via charge transfer bands of the vapor complex; and direct electron beam pumping

Caracterización mecánica de recubrimientos de aluminio por CVD-FBR sobre aceros inoxidables y resistencia a la oxidación en vapor de agua

OpenAIRE

Diego Pérez-Muñoz; José Luddey Marulanda-Arévalo; Juan Manuel Meza-Meza

2015-01-01

Los recubrimientos de aluminio depositados sobre el acero inoxidable austenítico AISI 317 por Deposición Química de Vapor en Lecho Fluidizado (CVD-FBR) presentan a altas temperaturas una reducción de la velocidad de corrosión de más de 80 veces. Se realizó la caracterización mecánica de los recubrimientos por medio de microdureza, nanoindentación, para conocer cómo se vieron afectas las propiedades mecánicas (en especial la dureza y el módulo de Young) del recubrimiento y del sustrato luego d...

Control of sodium vapor transport in annuli

International Nuclear Information System (INIS)

Meadows, G.E.; Bohringer, A.P.

1983-11-01

The method used to control sodium vapor transport in the annuli of various components at the Fast Flux Test Facility (FFTF) is a downward purge of the annuli with high purity argon. The purge rates for the FFTF were selected by calculating the gas velocity required to overcome thermal convection transport in the annuli. To evaluate the effectiveness of the gas purge, laboratory apparatus was fabricated which simulated selected annuli in the FFTF In-Vessel Handling Machine (IVHM) and the Instrument Tree (IT) annuli. Tests were conducted at temperatures similar to FFTF conditions. Gas purge rates ranged from zero to 130% of FFTF flow rates. Test results show the effectiveness of a high purity gas purge in decreasing the accumulation of sodium vapor deposits in an annulus. The presence of water vapor and oxygen in the purge gas increased the sodium deposition rate by a factor of three over other tests usig high purity argon. The presence of a vapor control collar used in the IT annulus was shown to be beneficial for controlling vapor transport into the upper region of the annulus

Vapor pressure and thermodynamics of beryllium carbide

International Nuclear Information System (INIS)

Rinehart, G.H.; Behrens, R.G.

1980-01-01

The vapor pressure of beryllium carbide has been measured over the temperature range 1388 to 1763 K using Knudsen-effusion mass spectrometry. Vaporization occurs incongruently according to the reaction Be 2 C(s) = 2Be(g) + C(s). The equilibrium vapor pressure above the mixture of Be 2 C and C over the experimental temperature range is (R/J K -1 mol -1 )ln(p/Pa) = -(3.610 +- 0.009) x 10 5 (K/T) + (221.43 +- 1.06). The third-law enthalpy change for the above reaction obtained from the present vapor pressures is ΔH 0 (298.15 K) = (740.5 +- 0.1) kJ mol -1 . The corresponding second-law result is ΔH 0 (298.15 K) = (732.0 +- 1.8) kJ mol -1 . The enthalpy of formation for Be 2 C(s) calculated from the present third-law vaporization enthalpy and the enthalpy of formation of Be(g) is ΔH 0 sub(f)(298.15 K) = -(92.5 +- 15.7) kJ mol -1 . (author)

Vapor-transport of tungsten and its geologic application

Energy Technology Data Exchange (ETDEWEB)

Shibue, Y [Hyogo Univ. of Teacher Education, Hyogo (Japan)

1988-11-10

The volatility of tungsten in a hydrous system at elevated temperatures and pressures was examined, and a tentative model for the enrichment of tungsten in hydrothermal solutions for the deposits related to granitic activities was proposed. To produce vapor-saturated solution, 17 or 15ml of 20wt% NaCl solution was introduced into an autoclave. Ca(OH){sub 2} for tungsten and H{sub 2}WO{sub 4} for base metals were used as vapor-captures, and run products were identified by X-ray powder diffractometry. The results suggested that the ratio of tungsten to base metals was higher in a vapor phase than in a liquid phase, and more enrichment of tungsten in the vapor phase occurred at higher temperature and pressure under the coexistence of the vapor and liquid phase. The tentative model emphasizing the vapor-transport of tungsten could explain the presence of tungsten deposits without large mineralization of base metals. Geological schematic model for the generation of the hydrothermal solution enriched in tungsten compared with base metals was illustrated based on above mentioned results. 21 refs., 3 figs.

Effect of vapor-phase oxygen on chemical vapor deposition growth of graphene

Science.gov (United States)

Terasawa, Tomo-o.; Saiki, Koichiro

2015-03-01

To obtain a large-area single-crystal graphene, chemical vapor deposition (CVD) growth on Cu is considered the most promising. Recently, the surface oxygen on Cu has been found to suppress the nucleation of graphene. However, the effect of oxygen in the vapor phase was not elucidated sufficiently. Here, we investigate the effect of O2 partial pressure (PO2) on the CVD growth of graphene using radiation-mode optical microscopy. The nucleation density of graphene decreases monotonically with PO2, while its growth rate reaches a maximum at a certain pressure. Our results indicate that PO2 is an important parameter to optimize in the CVD growth of graphene.

Growth of GaN layers using Ga2O vapor obtained from Ga and H2O vapor

International Nuclear Information System (INIS)

Sumi, Tomoaki; Taniyama, Yuuki; Takatsu, Hiroaki; Juta, Masami; Kitamoto, Akira; Imade, Mamoru; Yoshimura, Masashi; Mori, Yusuke; Isemura, Masashi

2015-01-01

In this study, we performed growth of GaN layers using Ga 2 O vapor synthesized from Ga and H 2 O vapor. In this process, we employed H 2 O vapor instead of HCl gas in hydride vapor phase epitaxy (HVPE) to synthesize Ga source gas. In the synthesis reaction of Ga 2 O, a Ga 2 O 3 whisker formed and covered Ga, which impeded the synthesis reaction of Ga 2 O. The formation of the Ga 2 O 3 whisker was suppressed in H 2 ambient at high temperatures. Then, we adopted this process to supply a group III precursor and obtained an epitaxial layer. X-ray diffraction (XRD) measurement revealed that the epitaxial layer was single-crystalline GaN. Growth rate increased linearly with Ga 2 O partial pressure and reached 104 µm/h. (author)

The separation of hydrocarbons from waste vapor streams

International Nuclear Information System (INIS)

Behling, R.D.; Ohlrogge, K.; Peinemann, K.V.; Kyburz, E.

1989-01-01

Hydrocarbon vapors generated from industrial processes dispersed into air are contributing factors for the creation of photochemical smog. The separation of hydrocarbon vapor by means of membranes is in case of some applications a technically simple and economic process. A membrane vapor separation process with a following treatment of the retentate by catalytic incineration is introduced in this paper

Efecto de las condiciones de secado sobre el endurecimiento de los granos de caraota (Phaseolus vulgaris pretratados con vapor

Directory of Open Access Journals (Sweden)

María Virginia Mujica

2017-12-01

Full Text Available El endurecimiento de los granos de caraota (Phaseolus vulgaris generado por el almacenamiento en condiciones de alta temperatura y humedad relativa representa una limitante importante para su consumo. El objetivo del presente trabajo fue evaluar el efecto de un tratamiento con vapor y luego secado a los granos de P. vulgaris recién cosechados en la prevención de su endurecimiento. Inicialmente, se construyeron las curvas de secado a 40; 47,5 y 55 ºC. Seguidamente, los granos se trataron con vapor por 8 min 20 s y se sometieron a un proceso de secado, bajo un diseño central compuesto cuyos factores fueron la temperatura del aire (40 y 55 ºC y el tiempo de secado (4 y 8 h. La muestra secada de cada tratamiento se dividió en 3 lotes, el primero se analizó de inmediato y los otros se almacenaron por 5 semanas bajo 2 condiciones distintas 5 ºC/34 % HR y 37 ºC/75 % HR. Las determinaciones realizadas fueron humedad, capacidad de imbibición, tiempo de cocción y actividad de la peroxidasa soluble. El tiempo de secado fue de 6,5; 5 y 2,5 h a 40; 47,5 y 55 ºC, respectivamente, para alcanzar una humedad de 13 % (b.s.. El coeficiente de difusión resultó igual a 3,40x10-9; 3,52x10-9 y 3,87x10-9 m2/s, a 40, 47,5 y 55 ºC, respectivamente. El valor de la energía de activación fue de 7,33 kJ/mol. La aplicación de vapor y posterior secado de los granos no previno su endurecimiento, y este no dependió de la actividad de la peroxidasa soluble. Por lo que se puede inferir que los compuestos fenólicos y la enzima peroxidasa no son los únicos implicados en el mecanismo de endurecimiento de los granos de P. vulgaris.

Separation of aromatics by vapor permeation through solvent swollen membrane

Energy Technology Data Exchange (ETDEWEB)

Ito, A.; Adachi, K.; Feng, Y. [Niigata University, Niigata (Japan)

1995-12-20

A vapor permeation process for aromatics separation from a hydrocarbon mixture was studied by means of the simultaneous permeation of dimethylsulfoxide vapor as an agent for membrane swelling and preferential permeation of aromatics. The separation performance of the process was demonstrated by a polyvinylalcohol membrane for mixed vapors of benzene/cyclohexane, xylene/octane and a model gasoline. The aromatic vapors preferentially permeated from these mixed vapor feeds. The separation factor was over 10. The separation mechanism of the process mainly depends on the relative salability of the vapors between aromatics and other hydrocarbons in dimethylsulfoxide. 14 refs., 9 figs., 1 tab.

Molecular dynamics study of the vaporization of an ionic drop.

Science.gov (United States)

Galamba, N

2010-09-28

The melting of a microcrystal in vacuum and subsequent vaporization of a drop of NaCl were studied through molecular dynamics simulations with the Born-Mayer-Huggins-Tosi-Fumi rigid-ion effective potential. The vaporization was studied for a single isochor at increasing temperatures until the drop completely vaporized, and gaseous NaCl formed. Examination of the vapor composition shows that the vapor of the ionic drop and gaseous NaCl are composed of neutral species, the most abundant of which, ranging from simple NaCl monomers (ion pairs) to nonlinear polymers, (Na(n)Cl(n))(n=2-4). The enthalpies of sublimation, vaporization, and dissociation of the different vapor species are found to be in reasonable agreement with available experimental data. The decrease of the enthalpy of vaporization of the vapor species, with the radius of the drop decrease, accounts for a larger fraction of trimers and tetramers than that inferred from experiments. Further, the rhombic dimer is significantly more abundant than its linear isomer although the latter increases with the temperature. The present results suggest that both trimers and linear dimers may be important to explain the vapor pressure of molten NaCl at temperatures above 1500 K.

Vapor condensation device

International Nuclear Information System (INIS)

Sakurai, Manabu; Hirayama, Fumio; Kurosawa, Setsumi; Yoshikawa, Jun; Hosaka, Seiichi.

1992-01-01

The present invention enables to separate and remove 14 C as CO 3 - ions without condensation in a vapor condensation can of a nuclear facility. That is, the vapor condensation device of the nuclear facility comprises (1) a spray pipe for spraying an acidic aqueous solution to the evaporation surface of an evaporation section, (2) a spray pump for sending the acidic aqueous solution to the spray pipe, (3) a tank for storing the acidic aqueous solution, (4) a pH sensor for detecting pH of the evaporation section, (5) a pH control section for controlling the spray pump, depending on the result of the detection of the pH sensor. With such a constitution, the pH of liquid wastes on the vaporization surface is controlled to 7 by spraying an aqueous solution of dilute sulfuric acid to the evaporation surface, thereby enabling to increase the transfer rate of 14 C to condensates to 60 to 70%. If 14 C is separated and removed as a CO 2 gas from the evaporation surface, the pH of the liquid wastes returns to the alkaline range of 9 to 10 and the liquid wastes are returned to a heating section. The amount of spraying the aqueous solution of dilute sulfuric acid can be controlled till the pH is reduced to 5. (I.S.)

Headspace gas and vapor characterization summary for the 43 vapor program suspect tanks

International Nuclear Information System (INIS)

Huckaby, J.L.; Bratzel, D.R.

1995-01-01

During the time period between February 1994 and September 1995, Westinghouse Hanford Company (WHC) sampled the waste tank headspace of 43 single-shell tanks for a variety of gaseous and/or volatile and semi-volatile compounds. This report summarizes the results of analyses of those sampling activities with respect to both the Priority 1 Safety Issues and relative to the detection in the headspace of significant concentrations of target analytes relating to worker breathing space consideration as recommended by the Pacific Northwest Laboratory (PNL) Toxicology Review Panel. The information contained in the data tables was abstracted from the vapor sampling and analysis tank characterization reports. Selected results are tabulated and summarized. Sampling equipment and methods, as well as sample analyses, are briefly described. Vapor sampling of passively ventilated single-shell tanks (tanks C-105, C-106, and SX-106 were sampled and are actively ventilated) has served to highlight or confirm tank headspace conditions associated with both priority 1 safety issues and supports source term analysis associated with protecting worker health and safety from noxious vapors

Experiences in the use of an electronic tool to measure pressure, temperature and spinner logs in the Mexican geothermal fields; Experiencias en el uso de sondas electronicas de presion, temperatura y flujo en campos geotermicos de Mexico

Energy Technology Data Exchange (ETDEWEB)

Flores Armenta, Magaly; Jaimes Maldonado, Guillermo [Gerencia de Proyectos Geotermoelectricos, Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

1999-08-01

In this article are exposed the results of an electronic tool to measure pressure-temperature and spinner profiles in the geothermal wells of Mexico, utilized in order to identify unobservable phenomena with traditional Kuster type pressure and temperature logs. Some examples of the applications are the identifications of production zones, interaction from between two or more zones of contribution under several conditions of operation, casing damages and apparition of sink flow intervals into the formation in producer wells. It is also presented the quantitative method utilized to calculate the masic contribution of the intervals of interest. [Spanish] En este articulo se exponen los resultados obtenidos mediante el uso de una sonda electronica para la medicion de presion-temperatura y flujo en los pozos geotermicos de Mexico, utilizada para identificar fenomenos que no son observables con las mediciones tradicionales tipo Kuster de presion y temperatura. Se ejemplifican algunas de las aplicaciones hechas, tales como la identificacion de zonas de produccion, forma de interaccion entre dos o mas zonas de aporte bajo diferentes condiciones de operacion, roturas en tuberias y aparicion de zonas ladronas en pozos. Se presenta brevemente el metodo cuantitativo utilizado para calcular el aporte masico de las intervalos de interes.

Fuel conditioning facility electrorefiner cadmium vapor trap operation

International Nuclear Information System (INIS)

Vaden, D. E.

1998-01-01

Processing sodium-bonded spent nuclear fuel at the Fuel Conditioning Facility at Argonne National Laboratory-West involves an electrometallurgical process employing a molten LiCl-KCl salt covering a pool of molten cadmium. Previous research has shown that the cadmium dissolves in the salt as a gas, diffuses through the salt layer and vaporizes at the salt surface. This cadmium vapor condenses on cool surfaces, causing equipment operation and handling problems. Using a cadmium vapor trap to condense the cadmium vapors and reflux them back to the electrorefiner has mitigated equipment problems and improved electrorefiner operations

Indirect heating of natural gas using vapor chambers; Aquecimento indireto de gas natural com uso de camaras de vapor

Energy Technology Data Exchange (ETDEWEB)

Milanez, Fernando H; Mantellil, Marcia H.B.; Borges, Thomaz P.F. [Santa Catarina Univ., Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica; Landa, Henrique G. de [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

2005-07-01

Operation safety and reliability are major guidelines in the design of city-gate units. Conventional natural gas heaters operate by a indirect mechanism, where liquid water is used to transfer heat by natural convection between the combustion chamber and the natural gas coil. In this work, the concept of vapor chamber is evaluated as an indirect gas heater. In a vapor chamber, liquid water is in contact with the heat source, and vaporizes. The vapor condenses in contact with the heat sink. A reduced scale model was built and tested in order to compare these two heating concepts where the combustion chamber was replaced by electrical cartridge heaters. This engineering model can operate either as a conventional heater or as a vapor chamber. The comparison between the concepts was done by inducing a controlled power to the cartridges and by measuring the resulting temperature distributions. In the novel design, the heat exchanger efficiency increases, and the thermal inertia decreases, compared to the conventional system. The new sealed concept of the chamber prevents water evaporation losses. (author)

Remedial actions to improve the availability in steam generators; Acciones correctivas para mejorar la disponibilidad en generadores de vapor

Energy Technology Data Exchange (ETDEWEB)

Torres Toledano, J. Gerardo; Porras Loaiza, G. Lizbeth; Sanchez Hernandez, Laura E.; Salinas B, Victor M.; Nebart G, Jesus [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

2001-07-01

was demonstrated that the lack of power of the unit is not due to the combustion air deficiency. The metallographic study of the fault of the RU tube is mentioned, where a graph of the estimated life span at different rates of wear by corrosion and metal temperature for a tube of SA-213-TPH metal is presented. The details of the interconnections at the reheater are shown and a table of comparison of proposed temperatures at the RH outlet is present. A table of main causes of power decrease is attached. [Spanish] En este articulo se presentan los resultados del analisis de fallas recurrentes de cuatro Unidades Generadoras de Centrales Termoelectricas (UGT) de la Comision Federal de Electricidad (CFE). En tres de los cuatro casos, los estudios se enfocaron a identificar y corregir las causas raiz de fallas recurrentes en tubos de generadores de vapor, las unidades analizadas son: U-2 del Complejo Termoelectrico Pdte. Adolfo Lopez Mateos (CTPALM) de Tuxpan, Veracruz; U-3 de la Central Termoelectrica (CT) de Salamanca, y U-1 y 2 de la CT Felipe Carrillo Puerto de Valladolid, Yucatan. En el otro caso se analizo la insuficiencia de aire de combustion como una de las causas de decremento de potencia de la unidad 1 de la CT Gral. Manuel Alvarez Moreno de Manzanillo, Colima. Los generadores de vapor de la unidad 2 del CTPALM y la unidad 3 de la CT de Salamanca presentaron fallas en el banco del recalentador (RH). En este caso las recomendaciones se enfocaron al mejoramiento en las condiciones operativas para atenuar las fallas por corrosion en alta temperatura. A diferencia del CTPALM, en el caso de la U-3 de Salamanca se concluyo que es necesario el rediseno del RH; para ello se propuso permutar trayectorias de tubos calientes con los frios para uniformizar la temperatura de vapor a la salida del RH. Para evaluar los problemas que se han presentado en el generador de vapor de las unidades 1 y 2 de la CT Felipe Carrillo Puerto de Valladolid, Yucatan se analizaron las fallas de

Water Vapor Remote Sensing Techniques: Radiometry and Solar Spectrometry

Science.gov (United States)

Somieski, A.; Buerki, B.; Cocard, M.; Geiger, A.; Kahle, H.-G.

The high variability of atmospheric water vapor content plays an important role in space geodesy, climatology and meteorology. Water vapor has a strong influence on transatmospheric satellite signals, the Earth's climate and thus the weather forecasting. Several remote sensing techniques have been developed for the determination of inte- grated precipitable water vapor (IPWV). The Geodesy and Geodynamics Lab (GGL) utilizes the methods of Water Vapor Radiometry and Solar Spectrometry to quantify the amount of tropospheric water vapor and its temporal variations. The Water Vapor Radiometer (WVR) measures the radiation intensity of the atmosphere in a frequency band ranging from 20 to 32 GHz. The Solar Atmospheric MOnitoring Spectrome- ter (SAMOS) of GGL is designed for high-resolution measurements of water vapor absorption lines using solar radiation. In the framework of the ESCOMPTE (ExpÊrience sur Site pour COntraindre les Mod- Éles de Pollution atmosphÊrique et de Transport d'Emissions) field campaign these instruments have been operated near Marseille in 2001. They have aquired a long time series of integrated precipitable water vapor content (IPWV). The accuracy of IPWV measured by WVR and SAMOS is 1 kg/m2. Furthermore meteorological data from radiosondes were used to calculate the IPWV in order to provide comparisons with the results of WVR and SAMOS. The methods of Water Vapor Radiometry and So- lar Spectrometry will be discussed and first preliminary results retrieved from WVR, SAMOS and radiosondes during the ESCOMPTE field campaign will be presented.

Mass spectrometric study of Nd2S3 vaporization

International Nuclear Information System (INIS)

Fenochka, B.V.

1987-01-01

The authors conduct a mass-spectrometric study of neodymium(III) sulfide vaporization. The chemical composition of the samples was stoichiometric and the samples were vaporized from tantalum effusion cells. When the vapor over Nd 2 S 3 is ionized by electrons the mass spectra shows monovalent cations of Nd, S, NdS, and NdO. The enthalpy of vaporization if Nd atoms from Nd 2 S 3 at average experimental temperatures and the standard enthalpy of reaction is shown. Also presented is the enthalpy of vaporization of NdS molecules from Nd 2 S 3 at average experimental temperatures and the standard enthalpy of reaction

Evaluación y adecuación de un tanque con agitador y chaqueta de vapor de 0,9 mc3 para la pasteurización de 880 kg. de pulpa de fruta

OpenAIRE

Espol; Palacios Ponce, Arturo Sócrates

2015-01-01

El presente trabajo tiene como finalidad instalar y adecuar un tanque con agitación y chaqueta de vapor para la pasteurización de 800kg por parada de pulpa de fruta con calidad y precio competitivo. Se evaluaron las condiciones operacionales del equipo y se validará la operatividad del mismo en condiciones ideales, posteriormente se determinarán los parámetros de proceso de tiempo y temperatura a través de corridas experimentales in situ. Los valores obtenidos en las pruebas experimentales se...

The vapor pressure and vaporization enthalpy of R-(+)-menthofuran, a hepatotoxin metabolically derived from the abortifacient terpene, (R)-(+)-pulegone by correlation gas chromatography

International Nuclear Information System (INIS)

Gobble, Chase; Chickos, James S.

2016-01-01

Highlights: • The vaporization enthalpy and vapor pressure of R-(+) menthofuran is evaluated. • The normal boiling temperature is predicted and compared to experimental and predicted values. • A vapor pressure equation as a function of temperature for menthofuran is evaluated. - Abstract: The vapor pressure as a function of temperature and its vaporization enthalpy at T = 298.15 K of R-(+)-menthofuran, a substance metabolically derived from R-(+)-pulegone that is both a flavoring agent at low concentrations and a hepatotoxin at larger ones, is evaluated by correlation-gas chromatography. A vapor pressure p/Pa = (36 ± 12) has been evaluated at T = 298.15 K, and a normal boiling temperature of T_b/K = 482.4 K is predicted. A boiling temperature of T_b/K = 374.3 compares with the literature value of T_b/K = 371.2 at reduced pressure, p/kPa = 2.93. The vaporization enthalpy of (56.5 ± 3.0) kJ·mol"−"1 compares to an estimated value of (57.8 ± 2.9) kJ·mol"−"1.

Auxiliary Electrodes for Chromium Vapor Sensors

Energy Technology Data Exchange (ETDEWEB)

Fergus, Jeffrey; Shahzad, Moaiz; Britt, Tommy

2018-05-15

Measurement of chromia-containing vapors in solid oxide fuel cell systems is useful for monitoring and addressing cell degradation caused by oxidation of the chomia scale formed on alloys for interconnects and balance-of-plant components. One approach to measuring chromium is to use a solid electrolyte with an auxiliary electrode that relates the partial pressure of the chromium containing species to the mobile species in the electrolyte. One example is YCrO3 which can equilibrate with the chromium containing vapor and yttrium in yttria stabilized zirconia to establish an oxygen activity. Another is Na2CrO4 which can equilibrate with the chromium-containing vapor to establish a sodium activity.

Vapor generation rate model for dispersed drop flow

International Nuclear Information System (INIS)

Unal, C.; Tuzla, K.; Cokmez-Tuzla, A.F.; Chen, J.C.

1991-01-01

A comparison of predictions of existing nonequilibrium post-CHF heat transfer models with the recently obtained rod bundle data has been performed. The models used the experimental conditions and wall temperatures to predict the heat flux and vapor temperatures at the location of interest. No existing model was able to reasonably predict the vapor superheat and the wall heat flux simultaneously. Most of the models, except Chen-Sundaram-Ozkaynak, failed to predict the wall heat flux, while all of the models could not predict the vapor superheat data or trends. A recently developed two-region heat transfer model, the Webb-Chen two-region model, did not give a reasonable prediction of the vapor generation rate in the far field of the CHF point. A new correlation was formulated to predict the vapor generation rate in convective dispersed droplet flow in terms of thermal-hydraulic parameters and thermodynamic properties. A comparison of predictions of the two-region heat transfer model, with the use of a presently developed correlation, with all the existing post-CHF data, including single-tube and rod bundle, showed significant improvements in predicting the vapor superheat and tube wall heat flux trends. (orig.)

Tritium-gas/water-vapor monitor. Tests and evaluation

International Nuclear Information System (INIS)

Jalbert, R.A.

1982-07-01

A tritium gas/water-vapor monitor was designed and built by the Health Physics Group at the Los Alamos National Laboratory. In its prototype configuration, the monitor took the shape of two separate instruments: a (total) tritium monitor and a water-vapor monitor. Both instruments were tested and evaluated. The tests of the (total) tritium monitor, basically an improved version of the standard flow-through ion-chamber instrument, are briefly reported here and more completely elsewhere. The tests of the water-vapor monitor indicated that the novel approach used to condense water vapor for scintillation counting has a number of serious drawbacks and that further development of the instrument is unwarranted

Influence of soil properties on vapor-phase sorption of trichloroethylene

International Nuclear Information System (INIS)

Bekele, Dawit N.; Naidu, Ravi; Chadalavada, Sreenivasulu

2016-01-01

Highlights: • Vapor intrusion is a major exposure pathway for volatile hydrocarbons. • Certainty in transport processes enhances vapor intrusion model precision. • Detailed understanding of vadose zone vapor transport processes save resources. • Vapor sorption near-steady-state conditions at sites may take months or years. • Type of clay fractions equitably affects sorption of trichloroethylene vapor. - Abstract: Current practices in health risk assessment from vapor intrusion (VI) using mathematical models are based on assumptions that the subsurface sorption equilibrium is attained. The time required for sorption to reach near-steady-state conditions at sites may take months or years to achieve. This study investigated the vapor phase attenuation of trichloroethylene (TCE) in five soils varying widely in clay and organic matter content using repacked columns. The primary indicators of TCE sorption were vapor retardation rate (R_t), the time required for the TCE vapor to pass through the soil column, and specific volume of retention (V_R), and total volume of TCE retained in soil. Results show TCE vapor retardation is mainly due to the rapid partitioning of the compound to SOM. However, the specific volume of retention of clayey soils with secondary mineral particles was higher. Linear regression analyses of the SOM and clay fraction with V_R show that a unit increase in clay fraction results in higher sorption of TCE (V_R) than the SOM. However, partitioning of TCE vapor was not consistent with the samples' surface areas but was mainly a function of the type of secondary minerals present in soils.

Influence of soil properties on vapor-phase sorption of trichloroethylene

Energy Technology Data Exchange (ETDEWEB)

Bekele, Dawit N. [Global Center for Environmental Remediation, University of Newcastle, Callaghan, NSW 2308 (Australia); CRC for Contamination Assessment & Remediation of the Environment, Building X (Environmental Sciences Building), University of South Australia, Mawson Lakes, SA 5095 (Australia); Naidu, Ravi, E-mail: Ravi.Naidu@newcastle.edu.au [Global Center for Environmental Remediation, University of Newcastle, Callaghan, NSW 2308 (Australia); CRC for Contamination Assessment & Remediation of the Environment, Building X (Environmental Sciences Building), University of South Australia, Mawson Lakes, SA 5095 (Australia); Chadalavada, Sreenivasulu [Global Center for Environmental Remediation, University of Newcastle, Callaghan, NSW 2308 (Australia); CRC for Contamination Assessment & Remediation of the Environment, Building X (Environmental Sciences Building), University of South Australia, Mawson Lakes, SA 5095 (Australia)

2016-04-05

Highlights: • Vapor intrusion is a major exposure pathway for volatile hydrocarbons. • Certainty in transport processes enhances vapor intrusion model precision. • Detailed understanding of vadose zone vapor transport processes save resources. • Vapor sorption near-steady-state conditions at sites may take months or years. • Type of clay fractions equitably affects sorption of trichloroethylene vapor. - Abstract: Current practices in health risk assessment from vapor intrusion (VI) using mathematical models are based on assumptions that the subsurface sorption equilibrium is attained. The time required for sorption to reach near-steady-state conditions at sites may take months or years to achieve. This study investigated the vapor phase attenuation of trichloroethylene (TCE) in five soils varying widely in clay and organic matter content using repacked columns. The primary indicators of TCE sorption were vapor retardation rate (R{sub t}), the time required for the TCE vapor to pass through the soil column, and specific volume of retention (V{sub R}), and total volume of TCE retained in soil. Results show TCE vapor retardation is mainly due to the rapid partitioning of the compound to SOM. However, the specific volume of retention of clayey soils with secondary mineral particles was higher. Linear regression analyses of the SOM and clay fraction with V{sub R} show that a unit increase in clay fraction results in higher sorption of TCE (V{sub R}) than the SOM. However, partitioning of TCE vapor was not consistent with the samples' surface areas but was mainly a function of the type of secondary minerals present in soils.

Uptake of mercury vapor by wheat. An assimilation model

International Nuclear Information System (INIS)

Browne, C.L.; Fang, S.C.

1978-01-01

Using a whole-plant chamber and 203 Hg-labeled mercury, a quantitative study was made of the effect of environmental parameters on the uptake, by wheat (Triticum aestivum), of metallic mercury vapor, an atmospheric pollutant. Factors were examined in relation to their influence on components of the gas-assimilation model, U(Hg) = (C/sub A' -- C/sub L')/(r/sub L.Hg/ + r/sub M.Hg/) where U(Hg) is the rate of mercury uptake per unit leaf surface, C/sub A'/ is the ambient mercury vapor concentration, C/sub L'/ is the mercury concentration at immobilization sites within the plant (assumed to be zero), r/sub L.Hg/ is the total leaf resistance to mercury vapor exchange, and r/sub M.Hg/ is a residual term to account for unexplained physical and biochemical resistances to mercury vapor uptake. Essentially all mercury vapor uptake was confined to the leaves. r/sub L.Hg/ was particularly influenced by illumination (0 to 12.8 klux), but unaffected by ambient temperature (17 to 33 0 C) and mercury vapor concentration (0 to 40 μg m -3 ). The principal limitation to mercury vapor uptake was r/sub M.Hg/, which was linearly related to leaf temperature, but unaffected by mercury vapor concentration and illumination, except for apparent high values in darkness. Knowing C/sub A'/ and estimating r/sub L.Hg/ and r/sub M.Hg/ from experimental data, mercury vapor uptake by wheat in light was accurately predicted for several durations of exposure using the above model

Volatilization of multicomponent mixtures in soil vapor extraction applications

International Nuclear Information System (INIS)

Bass, D.H.

1995-01-01

In soil vapor extraction (SVE) applications involving multicomponent mixtures, prediction of mass removal by volatilization as a function remediation extent is required to estimate remediation time and to size offgas treatment equipment. SVE is a commonly used remediation technology which volatilizes and enhances aerobic biodegradation of contamination adsorbed to vadose zone soils. SVE is often applied at sites contaminated with petroleum products, which are usually mixtures of many different compounds with vapor pressures spanning several orders of magnitude. The most volatile components are removed first, so the vapor pressure of the remaining contaminant continually decreases over the course of the remediation. A method for assessing how vapor pressure, and hence the rate of volatilization, of a multicomponent mixture changes over the course of a vapor extraction remedy has been developed. Each component is listed, alone, with its mass fraction in the mixture, in decreasing order of pure component vapor pressure (where component analyses are unavailable, model compounds can be used), For most petroleum distillates, the vapor pressure for each component plotted against the cumulative mass fraction of the component in the mixture on semilog coordinates will produce a straight line with a high correlation coefficient. This regression can be integrated to produce an expression for vapor pressure of the overall mixture as a function of extent or remediation

Composición química y actividad antibacteriana del aceite esencial del Origanum vulgare (orégano

Directory of Open Access Journals (Sweden)

Emilia Albado Plaus

2001-01-01

Full Text Available Objetivo: Determinar la actividad antimicrobiano en el aceite esencial (Carvacrol del Origanum vulgare. Material y métodos: El aceite esencial se obtuvo por destilación por arrastre con vapor de agua, a partir de las hojas y flores desecadas de O. vulgare; se determinó la gravedad especifica con un pinnómetro y el índice de refracción con refractómetro de Abbc; la composición química se evaluó mediante cromatografía de gas con detector de masa (GL-SM. La actividad antimicrobiana del aceite de O. vulgare se realizó por el método semicuantitativo de incorporación y de disco difusión en agar. Resultados: La densidad especifica del producto resultó 0.9234 a 20°C y el índice de refracción 1.4774; el cromatograma mostró un contenido de 9% de Carvacrol, 12.19% de Terpineol, 6.86% de P-cimeno y la presencia de otros compuesto relacionados metabolicamente con los tres antes citados. Las bacterias gram-negativas: Escherichia coli, Pseudomona aeruginosa, Salmonella tiphymurium, Salmonella cholerae suis y Vibrio cholerae y las bacterias gram-positivas: Staphylococcus aureus y Bacillus cereus, mostraron diferentes grados de sensibilidad. De los microorganismos evaluados solo pseudomonas aeruginosa mostró resistencia. Conclusión: El aceite esencial posee actividad microbiana contra todas las bacterias evaluadas, excepto antes para P. aeruginosa.(Rev Med Hered 2001; 12: 16-19 .

Vapor Pressures of Several Commercially Used Alkanolamines

NARCIS (Netherlands)

Klepacova, Katarina; Huttenhuis, Patrick J. G.; Derks, Peter W. J.; Versteeg, Geert F.; Klepáčová, Katarína

For the design of acid gas treating processes, vapor-liquid equilibrium (VLE) data must be available of the solvents to be applied. In this study the vapor pressures of seven frequently industrially used alkanolamines (diethanolamine, N-methylethanolamine, N,N-dimethylethanolamine,

Recommended vapor pressures for thiophene, sulfolane, and dimethyl sulfoxide

Czech Academy of Sciences Publication Activity Database

Fulem, Michal; Růžička, K.; Růžička, M.

2011-01-01

Roč. 303, č. 2 (2011), s. 205-216 ISSN 0378-3812 Institutional research plan: CEZ:AV0Z10100521 Keywords : thiophene sulfolane * dimethyl sulfoxide * vapor pressure * heat capacity * vaporization enthalpy * recommended vapor pressure equation Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.139, year: 2011

An evaluation of vapor extraction of vadose zone contamination

International Nuclear Information System (INIS)

Crotwell, A.T.; Waehner, M.J.; MacInnis, J.M.; Travis, C.C.; Lyon, B.F.

1992-05-01

An in-depth analysis of vapor extraction for remediation of soils contaminated with volatile organic compounds (VOCS) was conducted at 13 sites. The effectiveness of vapor extraction systems (VES) was evaluated on the basis of soil concentrations of VOCs and soil-gas concentrations of VOC's. The range of effectiveness was found to be 64%--99% effective in removing organic contaminants from soil. At nine of the 13 sites studied in this report, vapor extraction was found to be effective in reducing VOC cooncentrations by at least 90%. At the remaining four sites studied, vapor extraction was found to reduce VOC concentrations by less than 90%. Vapor extraction is ongoing at two of these sites. At a third, the ineffectiveness of the vapor extraction is attributed to the presence of ''hot spots'' of contamination. At the fourth site, where performance was found to be relatively poor, the presence of geological tar deposits at the site is thought to be a major factor in the ineffectiveness

Risk assessment of metal vapor arcing

Science.gov (United States)

Hill, Monika C. (Inventor); Leidecker, Henning W. (Inventor)

2009-01-01

A method for assessing metal vapor arcing risk for a component is provided. The method comprises acquiring a current variable value associated with an operation of the component; comparing the current variable value with a threshold value for the variable; evaluating compared variable data to determine the metal vapor arcing risk in the component; and generating a risk assessment status for the component.

Analysis of organic vapors with laser induced breakdown spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Nozari, Hadi; Tavassoli, Seyed Hassan [Laser and Plasma Research Institute, Shahid Beheshti University, G. C, 1983963113 Evin, Tehran (Iran, Islamic Republic of); Rezaei, Fatemeh, E-mail: fatemehrezaei@kntu.ac.ir [Department of Physics, K. N. Toosi University of Technology, 15875-4416 Shariati, Tehran (Iran, Islamic Republic of)

2015-09-15

In this paper, laser induced breakdown spectroscopy (LIBS) is utilized in the study of acetone, ethanol, methanol, cyclohexane, and nonane vapors. Carbon, hydrogen, oxygen, and nitrogen atomic emission spectra have been recorded following laser-induced breakdown of the organic vapors that are mixed with air inside a quartz chamber at atmospheric pressure. The plasma is generated with focused, Q-switched Nd:YAG radiation at the wavelength of 1064 nm. The effects of ignition and vapor pressure are discussed in view of the appearance of the emission spectra. The recorded spectra are proportional to the vapor pressure in air. The hydrogen and oxygen contributions diminish gradually with consecutive laser-plasma events without gas flow. The results show that LIBS can be used to characterize organic vapor.

Analysis of organic vapors with laser induced breakdown spectroscopy

International Nuclear Information System (INIS)

Nozari, Hadi; Tavassoli, Seyed Hassan; Rezaei, Fatemeh

2015-01-01

In this paper, laser induced breakdown spectroscopy (LIBS) is utilized in the study of acetone, ethanol, methanol, cyclohexane, and nonane vapors. Carbon, hydrogen, oxygen, and nitrogen atomic emission spectra have been recorded following laser-induced breakdown of the organic vapors that are mixed with air inside a quartz chamber at atmospheric pressure. The plasma is generated with focused, Q-switched Nd:YAG radiation at the wavelength of 1064 nm. The effects of ignition and vapor pressure are discussed in view of the appearance of the emission spectra. The recorded spectra are proportional to the vapor pressure in air. The hydrogen and oxygen contributions diminish gradually with consecutive laser-plasma events without gas flow. The results show that LIBS can be used to characterize organic vapor

Analysis of the transient compressible vapor flow in heat pipes

Science.gov (United States)

Jang, J. H.; Faghri, A.; Chang, W. S.

1989-01-01

The transient compressible one-dimensional vapor flow dynamics in a heat pipe is modeled. The numerical results are obtained by using the implicit non-iterative Beam-Warming finite difference method. The model is tested for simulated heat pipe vapor flow and actual vapor flow in cylindrical heat pipes. A good comparison of the present transient results for the simulated heat pipe vapor flow with the previous results of a two-dimensional numerical model is achieved and the steady state results are in agreement with the existing experimental data. The transient behavior of the vapor flow under subsonic, sonic, and supersonic speeds and high mass flow rates are successfully predicted. The one-dimensional model also describes the vapor flow dynamics in cylindrical heat pipes at high temperatures.

Analysis of the transient compressible vapor flow in heat pipe

International Nuclear Information System (INIS)

Jang, J.H.; Faghri, A.; Chang, W.S.

1989-07-01

The transient compressible one-dimensional vapor flow dynamics in a heat pipe is modeled. The numerical results are obtained by using the implicit non-iterative Beam-Warming finite difference method. The model is tested for simulated heat pipe vapor flow and actual vapor flow in cylindrical heat pipes. A good comparison of the present transient results for the simulated heat pipe vapor flow with the previous results of a two-dimensional numerical model is achieved and the steady state results are in agreement with the existing experimental data. The transient behavior of the vapor flow under subsonic, sonic, and supersonic speeds and high mass flow rates are successfully predicted. The one-dimensional model also describes the vapor flow dynamics in cylindrical heat pipes at high temperatures

Headspace vapor characterization of Hanford Waste Tank SX-102: Results from samples collected on July 19, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

McVeety, B.D.; Evans, J.C.; Clauss, T.W.; Pool, K.H.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-SX-102 (Tank SX-102) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed under the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5046. Samples were collected by WHC on July 19, 1995, using the vapor sampling system (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Headspace vapor characterization of Hanford Waste Tank AX-103: Results from samples collected on June 21, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

Ligotke, M.W.; Pool, K.H.; Clauss, T.W.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-AX-103 (Tank AX-103) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5029. Samples were collected by WHC on June 21, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Headspace vapor characterization of Hanford Waste Tank AX-101: Results from samples collected on June 15, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

Pool, K.H.; Clauss, T.W.; Evans, J.C.; McVeety, B.D.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-AX-101 (Tank AX-101) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) under the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5028. Samples were collected by WHC on June 15, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

46 CFR 182.480 - Flammable vapor detection systems.

Science.gov (United States)

2010-10-01

... 100 GROSS TONS) MACHINERY INSTALLATION Specific Machinery Requirements § 182.480 Flammable vapor... permit calibration in a vapor free atmosphere. (g) Electrical connections, wiring, and components for a...

External fuel vaporization study, phase 2

Science.gov (United States)

Szetela, E. J.; Chiappetta, L.

1981-01-01

An analytical study was conducted to evaluate the effect of variations in fuel properties on the design of an external fuel vaporizaton system. The fuel properties that were considered included thermal stability, critical temperature, enthalpy a critical conditions, volatility, and viscosity. The design parameters that were evaluated included vaporizer weight and the impact on engine requirement such as maintenance, transient response, performance, and altitude relight. The baseline fuel properties were those of Jet A. The variation in thermal stability was taken as the thermal stability variation for Experimental Referee Broad Specification (ERBS) fuel. The results of the analysis indicate that a change in thermal stability equivalent to that of ERBS would increase the vaporization system weight by 20 percent, decrease oprating time between cleaning by 40 percent and make altitude relight more difficult. An increase in fuel critical temperature of 39 K would require a 40 percent increase in vaporization system weight. The assumed increase in enthalpy and volatility would also increase vaporizer weight by 40 percent and make altitude relight extremely difficult. The variation in fuel viscosity would have a negligible effect on the design parameters.

Analysis regarding steam generator furnace's incident heat, temperature and composition of combustion gases; Analisis de calor incidente, temperatura y composicion de gases de combustion en hornos de generadores de vapor

Energy Technology Data Exchange (ETDEWEB)

Diego Marin, Antonio [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2006-07-01

In order to obtain more precise evaluations of the combustion process in the furnace of a steam generator a suction pyrometer has been integrated to measure the temperature of the combustion gases; an ellipsoidal radiometer to measure the incident heat by thermal radiation in the water walls; a water cooled probe to determine the particle concentration, as well as a water cooled probe to determine the composition of the combustion gases present. This document clarifies the form of use of these instruments and their engineering specifications, simultaneously presenting an analysis that considers, unlike others, the internal conditions of the furnace to obtain a more precise evaluation of the efficiency that the combustion process presents and bases for the taking of preventive actions in specific zones of the furnace. Thus, the present work exhibits instruments and techniques of analysis to study the phenomena occurring within a steam generator. [Spanish] Con el fin de obtener evaluaciones mas precisas del proceso de combustion en el horno de un generador de vapor, se ha integrado un pirometro de succion para medir la temperatura de los gases de combustion; un radiometro elipsoidal para medir el calor incidente por radiacion termica en las paredes del agua; una sonda enfriada con agua para determinar la concentracion de particulas, asi como una sonda refrigerada con agua para determinar la composicion de los gases de combustion presentes. Este documento aclara la forma de uso de estos instrumentos y sus especificaciones tecnicas, a la vez que presenta un analisis que considera, a diferencia de otros, las condiciones internas del horno para obtener una evaluacion mas precisa sobre la eficiencia del proceso de combustion y bases para la toma de acciones preventivas en zonas especificas del horno. Asi, el presente trabajo exhibe instrumentos y tecnicas de analisis para estudiar los fenomenos que ocurren dentro de un generador de vapor.

The liquid to vapor phase transition in excited nuclei

Energy Technology Data Exchange (ETDEWEB)

Elliott, J.B.; Moretto, L.G.; Phair, L.; Wozniak, G.J.; Beaulieu, L.; Breuer, H.; Korteling, R.G.; Kwiatkowski, K.; Lefort, T.; Pienkowski, L.; Ruangma, A.; Viola, V.E.; Yennello, S.J.

2001-05-08

For many years it has been speculated that excited nuclei would undergo a liquid to vapor phase transition. For even longer, it has been known that clusterization in a vapor carries direct information on the liquid-vapor equilibrium according to Fisher's droplet model. Now the thermal component of the 8 GeV/c pion + 197 Au multifragmentation data of the ISiS Collaboration is shown to follow the scaling predicted by Fisher's model, thus providing the strongest evidence yet of the liquid to vapor phase transition.

RDF gasification with water vapour: influence of process temperature on yield and products composition; Gassificazione con vapore del CDR: influenza della temperatura di processo su rese e composizione dei prodotti

Energy Technology Data Exchange (ETDEWEB)

Galvagno, S.; Casciaro, G.; Russo, A.; Casu, S.; Martino, M.; Portofino, S. [C. R. ENEA Trisaglia, Rotondella (Italy). PROT-STP

2005-08-01

The opportunity of using RDF (Refused Derived Fuel) to produce fuel gas seems to be promising and particular attention has been focused on alternative process technologies such as pyrolysis and gasification. Within this frame, present work relates to experimental tests and obtained results of a series of experimental surveys on RDF gasification with water vapour, carried out by means of a bench scale rotary kiln plant at different process temperature, using thermogravimetry (TG) and infrared spectrometry (FTIR), in order to characterize the incoming material, and online gas chromatography to qualify the gaseous stream. Experimental data show that gas yield rise with temperature and, with respect to the gas composition, hydrogen content grows up mainly at the expense of the other gaseous compound, pointing out the major extension of secondary cracking reactions into the gaseous fraction at higher temperature. Syngas obtained at process temperature of 950{sup o}C or higher seems to be suitable for fuel cells applications; at lower process temperature, gas composition suggest a final utilisation for feedstock recycling. The low organic content of solid residue does not suggest any other exploitation of the char apart from the land filling. [Italian] La possibilita' di usare il CDR (combustibile derivato dai rifiuti) per produrre gas combustibile, sembra particolarmente promettente e particolare attenzione si sta rivolgendo a tecnologie alternative di trattamento termico, quali la pirolisi e la gassificazione. In questo ambito, il presente lavoro riporta le prove sperimentali e i risultati ottenuti in una campagna di prove di gassificazione di CDR con vapor d'acqua, effettuate su scala banco in un forno a tamburo rotante a temperatura di processo variabile, utilizzando tecniche di analisi termogravimetrica (TG) e di spettrometria infrarossa in trasformata di Fourier (FTIR), per la caratterizzazione del materiale di ingresso, e analisi gascromatografiche on

Response to exploitation (1982-2002) of the Los Azufres, Michoacan (Mexico) geothermal field. Part I: North Zone; Respuesta a la explotacion (1982-2003) del yacimiento geotermico de Los Azufres, Michoacan (Mexico). Parte I: Zona Norte

Energy Technology Data Exchange (ETDEWEB)

Arellano G, Victor Manuel; Barragan R, Rosa Maria [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico); Torres R, Marco Antonio; Sandoval M, Fernando [Comision Federal de Electricidad, Morelia, Michoacan (Mexico)

2004-12-01

This work studies the thermodynamic evolution of the Los Azufres northern zone reservoir fluids as a response of exploitation since 1982 to 2002 is presented. Thermodynamic conditions for reservoir fluids were estimated using the WELFLO heat-and flow-well simulator, using production data as the input. The initial thermodynamic conditions of the north zone wells indicated the presence of compressed liquid; also it was noticed that the first response to exploitation was a pressure drop and an enthalpy increase, while the long term response indicated a very small pressure change but a high enthalpy increment. The analysis of production, chemical and isotopic (d18O, dD) data in this zone showed interference effects of fluids reinjected in well Az-52 on well Az-5; and in well Az-15 on wells Az-13, Az-28 and Az-43. At the present time due to the low injection flow rates, this effect is minimal. [Spanish] En este trabajo se presenta un estudio sobre la evolucion termodinamica de los fluidos de la zona norte del yacimiento de Los Azufres desde el inicio de su explotacion en 1982 hasta el ano 2002, considerando las condiciones de fondo de pozos del campo, como respuesta a la extraccion e inyeccion de fluidos. Las condiciones termodinamicas de los fluidos del yacimiento se estimaron mediante el simulador del flujo de fluidos y calor en pozos {sup W}ELFLO{sup ,} a partir de datos de produccion. Las condiciones termodinamicas iniciales de los fluidos de la zona norte de campo se encontraron en la region de liquido comprimido; la primera respuesta a la explotacion consistio en una disminucion de presion y un incremento en la entalpia. A largo plazo, se observaron cambios muy pequenos en la presion y grandes incrementos en la entalpia. El analisis de datos quimicos, isotopicos (d18O, dD) y de produccion de pozos en la zona norte evidencio la ocurrencia de interferencia de fluidos de reinyeccion del pozo Az-52 con el pozo Az-5 y del pozo Az-15 con los pozos Az-13, Az-28 y Az 43

Energy analysis of the production process of sugar using modern technologies of process integration; Analisis energetico del proceso de produccion del azucar utilizando tecnicas modernas de integracion de proceso

Energy Technology Data Exchange (ETDEWEB)

Figueroa Ibarra, Luis; Arriola Medellin, Alejandro [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

1999-07-01

The application of new concepts for the energy analysis of industrial processes, which consider the thermal integration of the process equipment, not only allows to detect energy recovery potentials that cannot be visualized with the traditional treatment of energy diagnosis of individual equipment, allows in addition, to suggest changes in the operation of the process that, without modifying the production, result in the reduction of the consumption of energy by the services and fuel. The analysis of thermal integration is illustrated for the case of a sugar mill, detecting a reduction potential in the use of fuel oil of 75%, and a potential increase of electrical production by cogeneration of 41%, departing from the modification of the use of the steam available in the process, and of the change of operation parameters of operation in the evaporation section. [Spanish] La aplicacion de nuevos conceptos para el analisis energetico de procesos industriales, los cuales consideran la integracion termica de los equipos del proceso, no unicamente permiten detectar potenciales de recuperacion de energia que no se pueden visualizar con el tratamiento tradicional de diagnostico energetico de equipos individuales, permiten ademas, sugerir cambios en la operacion del proceso que, sin modificar la produccion, redundan en una reduccion del consumo de servicios y combustible. El analisis de la integracion termica se ilustra para el caso de un ingenio azucarero, detectandose un potencial de reduccion del uso de combustoleo de 75%, y un potencial de incremento de produccion electrica por cogeneracion de 41%, a partir de la modificacion del uso del vapor disponible en el proceso, y del cambio de parametros de operacion en la seccion de evaporacion.

Vapor-fed bio-hybrid fuel cell.

Science.gov (United States)

Benyamin, Marcus S; Jahnke, Justin P; Mackie, David M

2017-01-01

Concentration and purification of ethanol and other biofuels from fermentations are energy-intensive processes, with amplified costs at smaller scales. To circumvent the need for these processes, and to potentially reduce transportation costs as well, we have previously investigated bio-hybrid fuel cells (FCs), in which a fermentation and FC are closely coupled. However, long-term operation requires strictly preventing the fermentation and FC from harming each other. We introduce here the concept of the vapor-fed bio-hybrid FC as a means of continuously extracting power from ongoing fermentations at ambient conditions. By bubbling a carrier gas (N 2 ) through a yeast fermentation and then through a direct ethanol FC, we protect the FC anode from the catalyst poisons in the fermentation (which are non-volatile), and also protect the yeast from harmful FC products (notably acetic acid) and from build-up of ethanol. Since vapor-fed direct ethanol FCs at ambient conditions have never been systematically characterized (in contrast to vapor-fed direct methanol FCs), we first assess the effects on output power and conversion efficiency of ethanol concentration, vapor flow rate, and FC voltage. The results fit a continuous stirred-tank reactor model. Over a wide range of ethanol partial pressures (2-8 mmHg), power densities are comparable to those for liquid-fed direct ethanol FCs at the same temperature, with power densities >2 mW/cm 2 obtained. We then demonstrate the continuous operation of a vapor-fed bio-hybrid FC with fermentation for 5 months, with no indication of performance degradation due to poisoning (of either the FC or the fermentation). It is further shown that the system is stable, recovering quickly from disturbances or from interruptions in maintenance. The vapor-fed bio-hybrid FC enables extraction of power from dilute bio-ethanol streams without costly concentration and purification steps. The concept should be scalable to both large and small

Vaporization of Samarium trichloride studied by thermogravimetry

International Nuclear Information System (INIS)

Esquivel, Marcelo R.; Pasquevich, Daniel M.

2003-01-01

In the present work, the vaporization reaction of SmCl 3 (l) obtained from the 'in situ' reaction of Sm 2 O 3 (s) and Cl 2 (g)-C(s) was studied by thermogravimetry under controlled atmosphere. The effects of both the temperature between 825 C degrees and 950 C degrees and the total flow gas on the vaporization rate of the following reaction: SmCl 3 (l) = SmCl 3 (g) were analyzed. The vaporization rate of the process was found to be independent of then total gas flow rate and highly dependent on the temperature. E ap calculation led to a value of 240 ± 10 kJ.mol -1 . A comparison between this value and that of the molar enthalpy of vaporization allow to the conclusion that the reaction occur in conditions near to equilibrium. The SmCl 3 identity was determined by X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS). (author)

General well function for soil vapor extraction

Science.gov (United States)

Perina, Tomas

2014-04-01

This paper develops a well function applicable to extraction of groundwater or soil vapor from a well under the most common field test conditions. The general well function (Perina and Lee, 2006) [12] is adapted to soil vapor extraction and constant head boundary at the top. For groundwater flow, the general well function now applies to an extraction well of finite diameter with uniform drawdown along the screen, finite-thickness skin, and partially penetrating an unconfined, confined, and leaky aquifer, or an aquifer underneath a reservoir. With a change of arguments, the model applies to soil vapor extraction from a vadose zone with no cover or with leaky cover at the ground surface. The extraction well can operate in specified drawdown (pressure for soil vapor) or specified flowrate mode. Frictional well loss is computed as flow-only dependent component of the drawdown inside the extraction well. In general case, the calculated flow distribution is not proportional to screen length for a multiscreen well.

Solvent vapor annealing of an insoluble molecular semiconductor

KAUST Repository

Amassian, Aram

2010-01-01

Solvent vapor annealing has been proposed as a low-cost, highly versatile, and room-temperature alternative to thermal annealing of organic semiconductors and devices. In this article, we investigate the solvent vapor annealing process of a model insoluble molecular semiconductor thin film - pentacene on SiO 2 exposed to acetone vapor - using a combination of optical reflectance and two-dimensional grazing incidence X-ray diffraction measurements performed in situ, during processing. These measurements provide valuable and new insight into the solvent vapor annealing process; they demonstrate that solvent molecules interact mainly with the surface of the film to induce a solid-solid transition without noticeable swelling, dissolving or melting of the molecular material. © 2010 The Royal Society of Chemistry.

Vaporization of comet nuclei: Light curves and life times

Energy Technology Data Exchange (ETDEWEB)

Cowan, J J [Harvard Univ., Cambridge, MA (USA). Center for Astrophysics; A' Hearn, M F [Maryland Univ., College Park (USA)

1979-10-01

The authors have examined the effects of vaporization from the nucleus of a comet and show that a latitude dependence of vaporization can, in some cases, explain asymmetries in commetary light curves. They also find that a non-uniform distribution of solar radiation over a comet can considerably shorten the vaporization lifetime compared to the results normally obtained by assuming that the nuclear surface is isothermal. Independent of any latitude effects, comets with CO/sub 2/-dominated nuclei and with periherlion distances less than 0.5 AU have vaporization lifetimes less than or comparable to their dynamical ejection times. This may explain the observed deficit of comets with small perihelion distances. Similarly comets with CO/sub 2/-dominated nuclei and perihelia near Jupiter's orbit have vaporization lifetimes that are shorter than the time for capture into short-period orbits. They suggest, therefore, that at least some new comets are composed in large part of CO/sub 2/, while only H/sub 2/O-dominated comets, with lower vaporization rates, can survive to be captured into short-period orbits.

46 CFR 39.40-1 - General requirements for vapor balancing-TB/ALL.

Science.gov (United States)

2010-10-01

... Section 39.40-1 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY TANK VESSELS VAPOR CONTROL SYSTEMS... to control vapor emissions during a lightering or topping-off operation which does not use vapor... compressor or blower to assist vapor transfer without approval from the Commandant (CG-522). (d) Vapor...

Monitoring tropospheric water vapor changes using radiosonde data

International Nuclear Information System (INIS)

Elliott, W.P.; Smith, M.E.; Angell, J.K.

1990-01-01

Significant increases in the water vapor content of the troposphere are expected to accompany temperature increases due to rising concentrations of the greenhouse gases. Thus it is important to follow changes in water vapor over time. There are a number of difficulties in developing a homogeneous data set, however, because of changes in radiosonde instrumentation and reporting practices. The authors report here on preliminary attempts to establish indices of water vapor which can be monitored. The precipitable water between the surface and 500 mb is the first candidate. They describe their method for calculating this quantity from radiosonde data for a network very similar to the network Angell uses for detecting temperature trends. Preliminary results suggest that the noise level is low enough to detect trends in water vapor at the individual stations. While a slight increase in global water vapor is hinted at in the data, and the data suggest there may have been a net transfer of water from the Southern Hemisphere to the Northern Hemisphere, these conclusions are tentative. The authors also discuss the future course of this investigation

Demand management in steam generation?; Administracion de la demanda en la generacion de vapor?

Energy Technology Data Exchange (ETDEWEB)

Plauchu L., A.; Plauchu A., J. A. [Ingenieros consultores (Mexico)

1997-12-31

Energy management has acquired capital importance in all the branches of the industrial activity and services either private o public and it has been, from years behind, more familiar the technology for the demand control in the electric power distribution systems, with excellent results in the energy conservation and economy. The rate of consumption for the different forms of energy shows the prevalence of the thermal energy in a variety of end uses. Not much or almost nothing has been said of the term Demand Management or Control in Steam Generation although 12% of the total energy supply is used for this purpose. Steam demand management and control can avoid unnecessary investments that bring along the increment of operational and maintenance problems and it is for sure that it will always give raise to a more rational and economical utilization of the real capacity of steam generation. A real case is commented. [Espanol] La administracion de la energia ha cobrado importancia capital en todos los giros de actividad industrial y de servicios, privados y publicos y es de varios anos atras cada vez mas familiar la tecnologia en el control de demanda en los sistemas de distribucion de energia electrica, con magnificos resultados en el ahorro, energetico y economico. La relacion de consumos para las diferentes formas de energia muestra el predominio de la energia termica en una variedad de usos finales. Poco o nada oimos del termino Administracion o Control de Demanda en la Generacion de Vapor aun cuando el 12% de la oferta total de energia tiene como destino esta aplicacion. La administracion y control de la demanda de vapor puede evitar inversiones innecesarias e incremento de problemas de operacion y mantenimiento y con seguridad reportaran siempre una utilizacion mas racional y economica de la capacidad real de generacion de vapor, se comenta un caso real.

Demand management in steam generation?; Administracion de la demanda en la generacion de vapor?

Energy Technology Data Exchange (ETDEWEB)

Plauchu L, A; Plauchu A, J A [Ingenieros consultores (Mexico)

1998-12-31

Energy management has acquired capital importance in all the branches of the industrial activity and services either private o public and it has been, from years behind, more familiar the technology for the demand control in the electric power distribution systems, with excellent results in the energy conservation and economy. The rate of consumption for the different forms of energy shows the prevalence of the thermal energy in a variety of end uses. Not much or almost nothing has been said of the term Demand Management or Control in Steam Generation although 12% of the total energy supply is used for this purpose. Steam demand management and control can avoid unnecessary investments that bring along the increment of operational and maintenance problems and it is for sure that it will always give raise to a more rational and economical utilization of the real capacity of steam generation. A real case is commented. [Espanol] La administracion de la energia ha cobrado importancia capital en todos los giros de actividad industrial y de servicios, privados y publicos y es de varios anos atras cada vez mas familiar la tecnologia en el control de demanda en los sistemas de distribucion de energia electrica, con magnificos resultados en el ahorro, energetico y economico. La relacion de consumos para las diferentes formas de energia muestra el predominio de la energia termica en una variedad de usos finales. Poco o nada oimos del termino Administracion o Control de Demanda en la Generacion de Vapor aun cuando el 12% de la oferta total de energia tiene como destino esta aplicacion. La administracion y control de la demanda de vapor puede evitar inversiones innecesarias e incremento de problemas de operacion y mantenimiento y con seguridad reportaran siempre una utilizacion mas racional y economica de la capacidad real de generacion de vapor, se comenta un caso real.

Secondhand Exposure to Vapors From Electronic Cigarettes

Science.gov (United States)

Czogala, Jan; Fidelus, Bartlomiej; Zielinska-Danch, Wioleta; Travers, Mark J.; Sobczak, Andrzej

2014-01-01

Introduction: Electronic cigarettes (e-cigarettes) are designed to generate inhalable nicotine aerosol (vapor). When an e-cigarette user takes a puff, the nicotine solution is heated and the vapor is taken into lungs. Although no sidestream vapor is generated between puffs, some of the mainstream vapor is exhaled by e-cigarette user. The aim of this study was to evaluate the secondhand exposure to nicotine and other tobacco-related toxicants from e-cigarettes. Materials and Methods: We measured selected airborne markers of secondhand exposure: nicotine, aerosol particles (PM2.5), carbon monoxide, and volatile organic compounds (VOCs) in an exposure chamber. We generated e-cigarette vapor from 3 various brands of e-cigarette using a smoking machine and controlled exposure conditions. We also compared secondhand exposure with e-cigarette vapor and tobacco smoke generated by 5 dual users. Results: The study showed that e-cigarettes are a source of secondhand exposure to nicotine but not to combustion toxicants. The air concentrations of nicotine emitted by various brands of e-cigarettes ranged from 0.82 to 6.23 µg/m3. The average concentration of nicotine resulting from smoking tobacco cigarettes was 10 times higher than from e-cigarettes (31.60±6.91 vs. 3.32±2.49 µg/m3, respectively; p = .0081). Conclusions: Using an e-cigarette in indoor environments may involuntarily expose nonusers to nicotine but not to toxic tobacco-specific combustion products. More research is needed to evaluate health consequences of secondhand exposure to nicotine, especially among vulnerable populations, including children, pregnant women, and people with cardiovascular conditions. PMID:24336346

Does mercury vapor exposure increase urinary selenium excretion

Energy Technology Data Exchange (ETDEWEB)

Hongo, T; Suzuki, T; Himeno, S; Watanabe, C; Satoh, H; Shimada, Y

1985-01-01

It has been reported that an increase of urinary selenium excretion may occur as a result of mercury vapor exposure. However, experimental data regarding the interaction between mercury vapor and selenium have yielded ambiguous results about the retention and elimination of selenium due to mercury vapor exposure and the decrease of selenium excretion due to mercury in the form of mercuric mercury (Hg/sup 2 +/). In this study, the authors measured urinary mercury and selenium in workers with or without exposure to mercury vapor to determine whether or not urinary selenium excretion was increased as a result of mercury vapor exposure. Urine samples were collected from 141 workers, 71 men and 70 women, whose extent of exposure to mercury vapor varied according to their job sites. Workers were divided into five groups according to their urinary mercury levels. The mercury level in group I was less than 2.8 nmol/mmol creatinine which means that this group was mostly free from mercury exposure. The average age was almost identical among the groups. For both sexes, group V (with the highest urinary mercury level) had the lowest urinary selenium level, but one-way variance analysis (ANOVA) did not reveal any significant variations of urinary selenium with urinary mercury levels; however, a weak but significant negative correlation between mercury and selenium was found in men.

Water-vapor pressure control in a volume

Science.gov (United States)

Scialdone, J. J.

1978-01-01

The variation with time of the partial pressure of water in a volume that has openings to the outside environment and includes vapor sources was evaluated as a function of the purging flow and its vapor content. Experimental tests to estimate the diffusion of ambient humidity through openings and to validate calculated results were included. The purging flows required to produce and maintain a certain humidity in shipping containers, storage rooms, and clean rooms can be estimated with the relationship developed here. These purging flows are necessary to prevent the contamination, degradation, and other effects of water vapor on the systems inside these volumes.

Water vapor retrieval over many surface types

Energy Technology Data Exchange (ETDEWEB)

Borel, C.C.; Clodius, W.C.; Johnson, J.

1996-04-01

In this paper we present a study of of the water vapor retrieval for many natural surface types which would be valuable for multi-spectral instruments using the existing Continuum Interpolated Band Ratio (CIBR) for the 940 nm water vapor absorption feature. An atmospheric code (6S) and 562 spectra were used to compute the top of the atmosphere radiance near the 940 nm water vapor absorption feature in steps of 2.5 nm as a function of precipitable water (PW). We derive a novel technique called ``Atmospheric Pre-corrected Differential Absorption`` (APDA) and show that APDA performs better than the CIBR over many surface types.

Peces del Noroeste del Ecuador

OpenAIRE

Barriga, Ramiro

1994-01-01

La ictiofauna del occidente del Ecuador es poco conocida. Los peces del noroccidente son diferentes a los del suroccidente del Ecuador. 34 familias y 82 especies fueron colectadas que equivale al 11 % de las especies de peces continentales registradas en el Ecuador. Icteogeográficamente se sabe que la costa ecuatoriana posee dos provincias: la del Pacifico Norte y la del Guayas, se determinó que el límite de las dos provincias es el río Santiago ya que las especies del mencionado río so...

Review of enhanced vapor diffusion in porous media

International Nuclear Information System (INIS)

Webb, S.W.; Ho, C.K.

1998-01-01

Vapor diffusion in porous media in the presence of its own liquid has often been treated similar to gas diffusion. The gas diffusion rate in porous media is much lower than in free space due to the presence of the porous medium and any liquid present. However, enhanced vapor diffusion has also been postulated such that the diffusion rate may approach free-space values. Existing data and models for enhanced vapor diffusion, including those in TOUGH2, are reviewed in this paper

Microscale interfacial behavior at vapor film collapse on high-temperature particle surface

International Nuclear Information System (INIS)

Abe, Yutaka; Tochio, Daisuke

2009-01-01

It has been pointed out that vapor film on a premixed high-temperature droplet surface should be collapsed to trigger vapor explosion. Thus, it is important to clarify the micromechanism of vapor film collapse behavior for the occurrence of vapor explosion. In the present study, microscale vapor-liquid interface behavior upon vapor film collapse caused by an external pressure pulse is experimentally observed and qualitatively analyzed. In the analytical investigation, interfacial temperature and interface movement were estimated with heat conduction analysis and visual data processing technique. Results show that condensation can possibly occur at the vapor-liquid interface when the pressure pulse arrived. That is, this result indicates that the vapor film collapse behavior is dominated not by fluid motion but by phase change. (author)

Headspace vapor characterization of Hanford Waste Tank 241-T-110: Results from samples collected on August 31, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

McVeety, B.D.; Thomas, B.L.; Evans, J.C.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-T-110 (Tank T-110) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5056. Samples were collected by WHC on August 31, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Headspace vapor characterization of Hanford Waste Tank 241-TX-111: Results from samples collected on October 12, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

Pool, K.H.; Clauss, T.W.; Evans, J.C.

1996-06-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-TX-111 (Tank TX-111) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5069. Samples were collected by WHC on October 12, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Headspace vapor characterization of Hanford Waste Tank 241-SX-109: Results from samples collected on August 1, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

Pool, K.H.; Clauss, T.W.; Evans, J.C.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-SX-109 (Tank SX-109) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5048. Samples were collected by WHC on August 1, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Headspace vapor characterization of Hanford Waste Tank 241-SX-104: Results from samples collected on July 25, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

Thomas, B.L.; Clauss, T.W.; Evans, J.C.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-SX-104 (Tank SX-104) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5049. Samples were collected by WHC on July 25, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Headspace vapor characterization of Hanford Waste Tank 241-S-112: Results from samples collected on July 11, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

Clauss, T.W.; Pool, K.H.; Evans, J.C.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage Tank 241-S-112 (Tank S-112) at the Hanford. Pacific Northwest National Laboratory (PNNL) is contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5044. Samples were collected by WHC on July 11, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Headspace vapor characterization of Hanford Waste Tank 241-SX-105: Results from samples collected on July 26, 1995. Tank Vapor Characterization Project

International Nuclear Information System (INIS)

Pool, K.H.; Clauss, T.W.; Evans, J.C.

1996-05-01

This report describes the results of vapor samples taken from the headspace of waste storage tank 241-SX-105 (Tank SX-105) at the Hanford Site in Washington State. Pacific Northwest National Laboratory (PNNL) contracted with Westinghouse Hanford Company (WHC) to provide sampling devices and analyze samples for inorganic and organic analytes collected from the tank headspace and ambient air near the tank. The analytical work was performed by the PNNL Vapor Analytical Laboratory (VAL) by the Tank Vapor Characterization Project. Work performed was based on a sample and analysis plan (SAP) prepared by WHC. The SAP provided job-specific instructions for samples, analyses, and reporting. The SAP for this sample job was open-quotes Vapor Sampling and Analysis Planclose quotes, and the sample job was designated S5047. Samples were collected by WHC on July 26, 1995, using the Vapor Sampling System (VSS), a truck-based sampling method using a heated probe inserted into the tank headspace

Comparison of vapor sampling system (VSS) and in situ vapor sampling (ISVS) methods on Tanks C-107, BY-108, and S-102. Revision 1

International Nuclear Information System (INIS)

Huckaby, J.L.; Edwards, J.A.; Evans, J.C.

1996-08-01

This report discusses comparison tests for two methods of collecting vapor samples from the Hanford Site high-level radioactive waste tank headspaces. The two sampling methods compared are the truck-mounted vapor sampling system (VSS) and the cart-mounted in-situ vapor sampling (ISVS). Three tanks were sampled by both the VSS and ISVS methods from the same access risers within the same 8-hour period. These tanks have diverse headspace compositions and they represent the highest known level of several key vapor analytes

Metal Vapor Arcing Risk Assessment Tool

Science.gov (United States)

Hill, Monika C.; Leidecker, Henning W.

2010-01-01

The Tin Whisker Metal Vapor Arcing Risk Assessment Tool has been designed to evaluate the risk of metal vapor arcing and to help facilitate a decision toward a researched risk disposition. Users can evaluate a system without having to open up the hardware. This process allows for investigating components at risk rather than spending time and money analyzing every component. The tool points to a risk level and provides direction for appropriate action and documentation.

Pretreated Butterfly Wings for Tuning the Selective Vapor Sensing.

Science.gov (United States)

Piszter, Gábor; Kertész, Krisztián; Bálint, Zsolt; Biró, László Péter

2016-09-07

Photonic nanoarchitectures occurring in the scales of Blue butterflies are responsible for their vivid blue wing coloration. These nanoarchitectures are quasi-ordered nanocomposites which are constituted from a chitin matrix with embedded air holes. Therefore, they can act as chemically selective sensors due to their color changes when mixing volatile vapors in the surrounding atmosphere which condensate into the nanoarchitecture through capillary condensation. Using a home-built vapor-mixing setup, the spectral changes caused by the different air + vapor mixtures were efficiently characterized. It was found that the spectral shift is vapor-specific and proportional with the vapor concentration. We showed that the conformal modification of the scale surface by atomic layer deposition and by ethanol pretreatment can significantly alter the optical response and chemical selectivity, which points the way to the efficient production of sensor arrays based on the knowledge obtained through the investigation of modified butterfly wings.

Excessively High Vapor Pressure of Al-based Amorphous Alloys

Directory of Open Access Journals (Sweden)

Jae Im Jeong

2015-10-01

Full Text Available Aluminum-based amorphous alloys exhibited an abnormally high vapor pressure at their approximate glass transition temperatures. The vapor pressure was confirmed by the formation of Al nanocrystallites from condensation, which was attributed to weight loss of the amorphous alloys. The amount of weight loss varied with the amorphous alloy compositions and was inversely proportional to their glass-forming ability. The vapor pressure of the amorphous alloys around 573 K was close to the vapor pressure of crystalline Al near its melting temperature, 873 K. Our results strongly suggest the possibility of fabricating nanocrystallites or thin films by evaporation at low temperatures.

Vapor characterization of Tank 241-C-103

International Nuclear Information System (INIS)

Huckaby, J.L.; Story, M.S.

1994-06-01

The Westinghouse Hanford Company Tank Vapor Issue Resolution Program has developed, in cooperation with Northwest Instrument Systems, Inc., Oak Ridge National Laboratory, Oregon Graduate Institute of Science and Technology, Pacific Northwest Laboratory, and Sandia National Laboratory, the equipment and expertise to characterize gases and vapors in the high-level radioactive waste storage tanks at the Hanford Site in south central Washington State. This capability has been demonstrated by the characterization of the tank 241-C-103 headspace. This tank headspace is the first, and for many reasons is expected to be the most problematic, that will be characterized (Osborne 1992). Results from the most recent and comprehensive sampling event, sample job 7B, are presented for the purpose of providing scientific bases for resolution of vapor issues associated with tank 241-C-103. This report is based on the work of Clauss et al. 1994, Jenkins et al. 1994, Ligotke et al. 1994, Mahon et al. 1994, and Rasmussen and Einfeld 1994. No attempt has been made in this report to evaluate the implications of the data presented, such as the potential impact of headspace gases and vapors to tank farm workers health. That and other issues will be addressed elsewhere. Key to the resolution of worker health issues is the quantitation of compounds of toxicological concern. The Toxicology Review Panel, a panel of Pacific Northwest Laboratory experts in various areas, of toxicology, has chosen 19 previously identified compounds as being of potential toxicological concern. During sample job 7B, the sampling and analytical methodology was validated for this preliminary list of compounds of toxicological concern. Validation was performed according to guidance provided by the Tank Vapor Conference Committee, a group of analytical chemists from academic institutions and national laboratories assembled and commissioned by the Tank Vapor Issue Resolution Program

Vapor characterization of Tank 241-C-103

Energy Technology Data Exchange (ETDEWEB)

Huckaby, J.L. [Westinghouse Hanford Co., Richland, WA (United States); Story, M.S. [Northwest Instrument Systems, Inc. Richland, WA (United States)

1994-06-01

The Westinghouse Hanford Company Tank Vapor Issue Resolution Program has developed, in cooperation with Northwest Instrument Systems, Inc., Oak Ridge National Laboratory, Oregon Graduate Institute of Science and Technology, Pacific Northwest Laboratory, and Sandia National Laboratory, the equipment and expertise to characterize gases and vapors in the high-level radioactive waste storage tanks at the Hanford Site in south central Washington State. This capability has been demonstrated by the characterization of the tank 241-C-103 headspace. This tank headspace is the first, and for many reasons is expected to be the most problematic, that will be characterized (Osborne 1992). Results from the most recent and comprehensive sampling event, sample job 7B, are presented for the purpose of providing scientific bases for resolution of vapor issues associated with tank 241-C-103. This report is based on the work of Clauss et al. 1994, Jenkins et al. 1994, Ligotke et al. 1994, Mahon et al. 1994, and Rasmussen and Einfeld 1994. No attempt has been made in this report to evaluate the implications of the data presented, such as the potential impact of headspace gases and vapors to tank farm workers health. That and other issues will be addressed elsewhere. Key to the resolution of worker health issues is the quantitation of compounds of toxicological concern. The Toxicology Review Panel, a panel of Pacific Northwest Laboratory experts in various areas, of toxicology, has chosen 19 previously identified compounds as being of potential toxicological concern. During sample job 7B, the sampling and analytical methodology was validated for this preliminary list of compounds of toxicological concern. Validation was performed according to guidance provided by the Tank Vapor Conference Committee, a group of analytical chemists from academic institutions and national laboratories assembled and commissioned by the Tank Vapor Issue Resolution Program.

Muonium formation and the 'missing fraction' in vapors

International Nuclear Information System (INIS)

Fleming, D.G.; Arseneau, D.J.; Garner, D.M.; Senba, M.; Mikula, R.J.

1983-06-01

The vapor phase fractional polarizations of positive muons thermalizing as the muonium atom (Psub(M)) and in diamagnetic environments (Psub(D)) has been measured in H 2 O, CH 3 OH, C 6 H 14 , C 6 H 12 , CCl 4 , CHCl 3 , CH 2 Cl 2 and TMS, in order to compare with the corresponding fractions measured in the condensed phases. There is a marked contrast in every case, with the vapor phase results being largely understandable in terms of a charge exchange/hot atom model. Unlike the situation in the corresponding liquids, there is no permanent lost fraction in the vapor phase in the limit of even moderately high pressures (approximately 1 atm); at lower pressures, depolarization is due to hyperfine mixing and is believed to be well understood. For vapor phase CH 3 OH, C 6 H 14 , C 6 H 12 , and TMS the relative fractions are found to be pressure dependent, suggesting the importance of termolecular hot atom (or ion) reactions in the slowing-down process. For vapor phase H 2 O and the chloromethanes, the relative fractions are pressure independent. For CCl 4 , Psub(M) = Psub(D) approximately 0.5 in the vapor phase vs. Psub(D) = 1.0 in the liquid phase; fast thermal reactions of Mu likely contribute significantly to this difference in the liquid phase. For H 2 O, Psub(M) approximately 0.9 and Psub(D) approximately 0.1 in the vapor phase vs. Psub(D) approximately 0.6 and Psub(M) approximately 0.2 in the liquid phase. Water appears to be the one unequivocal case where the basic charge exchange/hot atom model is inappropriate in the condensed phase, suggesting, therefore, that radiation-induced 'spur' effects play a major role

Similarities and differences in vapor explosion criteria

International Nuclear Information System (INIS)

Cronenberg, A.W.

1978-01-01

An overview of recent ideas pertaining to vapor explosion criteria indicates that in general sense, a consensus of opinion is emerging on the conditions applicable to explosive vaporization. Experimental and theoretical work has lead a number of investigators to the formulation of such conditions which are quite similar in many respects, although the quantitative details of the model formulation of such conditions are somewhat different. All model concepts are consistent in that an initial period of stable film boiling, separating molten fuel from coolant, is considered necessary (at least for large-scale interactions and efficient intermixing), with subsequent breakdown of film boiling due to pressure and/or thermal effects, followed by intimate fuel-coolant contact and a rapid vaporization process which is sufficient to cause shock pressurization. Although differences arise as to the conditions for and the energetics associated with film boiling destabilization and the mode and energetics of fragmentation and intermixing. However, the principal area of difference seems to be the question of what constitutes the requisite condition(s) for rapid vapor production to cause shock pressurization

A heated vapor cell unit for DAVLL in atomic rubidium

OpenAIRE

McCarron, Daniel J.; Hughes, Ifan G.; Tierney, Patrick; Cornish, Simon L.

2007-01-01

The design and performance of a compact heated vapor cell unit for realizing a dichroic atomic vapor laser lock (DAVLL) for the D2 transitions in atomic rubidium is described. A 5 cm-long vapor cell is placed in a double-solenoid arrangement to produce the required magnetic field; the heat from the solenoid is used to increase the vapor pressure and correspondingly the DAVLL signal. We have characterized experimentally the dependence of important features of the DAVLL signal on magnetic field...

Vapor pressures and thermophysical properties of selected monoterpenoids

Czech Academy of Sciences Publication Activity Database

Štejfa, V.; Dergal, F.; Mokbel, I.; Fulem, Michal; Jose, J.; Růžička, K.

2015-01-01

Roč. 406, Nov (2015), 124-133 ISSN 0378-3812 Institutional support: RVO:68378271 Keywords : monoterpenoids * vapor pressure * heat capacity * ideal - gas thermodynamic properties * vaporization and sublimation enthalpy Subject RIV: BJ - Thermodynamics Impact factor: 1.846, year: 2015

Water vapor estimation using digital terrestrial broadcasting waves

Science.gov (United States)

Kawamura, S.; Ohta, H.; Hanado, H.; Yamamoto, M. K.; Shiga, N.; Kido, K.; Yasuda, S.; Goto, T.; Ichikawa, R.; Amagai, J.; Imamura, K.; Fujieda, M.; Iwai, H.; Sugitani, S.; Iguchi, T.

2017-03-01

A method of estimating water vapor (propagation delay due to water vapor) using digital terrestrial broadcasting waves is proposed. Our target is to improve the accuracy of numerical weather forecast for severe weather phenomena such as localized heavy rainstorms in urban areas through data assimilation. In this method, we estimate water vapor near a ground surface from the propagation delay of digital terrestrial broadcasting waves. A real-time delay measurement system with a software-defined radio technique is developed and tested. The data obtained using digital terrestrial broadcasting waves show good agreement with those obtained by ground-based meteorological observation. The main features of this observation are, no need for transmitters (receiving only), applicable wherever digital terrestrial broadcasting is available and its high time resolution. This study shows a possibility to estimate water vapor using digital terrestrial broadcasting waves. In the future, we will investigate the impact of these data toward numerical weather forecast through data assimilation. Developing a system that monitors water vapor near the ground surface with time and space resolutions of 30 s and several kilometers would improve the accuracy of the numerical weather forecast of localized severe weather phenomena.

Numerical modeling of a vaporizing multicomponent droplet

Science.gov (United States)

Megaridis, C. M.; Sirignano, W. A.

The fundamental processes governing the energy, mass, and momentum exchange between the liquid and gas phases of vaporizing, multicomponent liquid droplets have been investigated. The axisymmetric configuration under consideration consists of an isolated multicomponent droplet vaporizing in a convective environment. The model considers different volatilities of the liquid components, variable liquid properties due to variation of the species concentrations, and non-Fickian multicomponent gaseous diffusion. The bicomponent droplet model was employed to examine the commonly used assumptions of unity Lewis number in the liquid phase and Fickian gaseous diffusion. It is found that the droplet drag coefficients, the vaporization rates, and the related transfer numbers are not influenced by the above assumptions in a significant way.

Vaporization of tungsten-metal in steam at high temperatures

International Nuclear Information System (INIS)

Greene, G.A.; Finfrock, C.C.

2000-01-01

The vaporization of tungsten from the APT spallation target dominates the radiological source term for unmitigated target overheating accidents. Chemical reactions of tungsten with steam which persist to tungsten temperatures as low as 800 C result in the formation of a hydrated tungsten-oxide which has a high vapor pressure and is readily convected in a flowing atmosphere. This low-temperature vaporization reaction essentially removes the oxide film that forms on the tungsten-metal surface as soon as it forms, leaving behind a fresh metallic surface for continued oxidation and vaporization. Experiments were conducted to measure the oxidative vaporization rates of tungsten in steam as part of the effort to quantify the MT radiological source term for severe target accidents. Tests were conducted with tungsten rods (1/8 inch diameter, six inches long) heated to temperatures from approximately 700 C to 1350 C in flowing steam which was superheated to 140 C. A total of 19 experiments was conducted. Fifteen tests were conducted by RF induction heating of single tungsten rods held vertical in a quartz glass retort. Four tests were conducted in a vertically-mounted tube furnace for the low temperature range of the test series. The aerosol which was generated and transported downstream from the tungsten rods was collected by passing the discharged steam through a condenser. This procedure insured total collection of the steam along with the aerosol from the vaporization of the rods. The results of these experiments revealed a threshold temperature for tungsten vaporization in steam. For the two tests at the lowest temperatures which were tested, approximately 700 C, the tungsten rods were observed to oxidize without vaporization. The remainder of the tests was conducted over the temperature range of 800 C to 1350 C. In these tests, the rods were found to have lost weight due to vaporization of the tungsten and the missing weight was collected in the downstream condensate

Using in situ bioventing to minimize soil vapor extraction costs

International Nuclear Information System (INIS)

Downey, D.C.; Frishmuth, R.A.; Archabal, S.R.; Pluhar, C.J.; Blystone, P.G.; Miller, R.N.

1995-01-01

Gasoline-contaminated soils may be difficult to remediate with bioventing because high concentrations of gasoline vapors become mobile when air is injected into the soil. Because outward vapor migration is often unacceptable on small commercial sites, soil vapor extraction (SVE) or innovative bioventing techniques are required to control vapors and to increase soil gas oxygen levels to stimulate hydrocarbon biodegradation. Combinations of SVE, off-gas treatment, and bioventing have been used to reduce the costs normally associated with remediation of gasoline-contaminated sites. At Site 1, low rates of pulsed air injection were used to provide oxygen while minimizing vapor migration. At Site 2, a period of high-rate SVE and off-gas treatment was followed by long-term air injection. Site 3 used an innovative approach that combined regenerative resin for ex situ vapor treatment with in situ bioventing to reduce the overall cost of site remediation. At each of these Air Force sites, bioventing provided cost savings when compared to more traditional SVE methods

Results of test of acid fluids neutralization in the well H-43, Los Humeros geothermal field, Puebla; Resultados de la prueba de neutralizacion de fluidos acidos en el pozo H-43, campo geotermico de Los Humeros, Puebla

Energy Technology Data Exchange (ETDEWEB)

Flores Armenta, Magaly del Carmen; Ramirez Montes, Miguel; Sandoval Medina, Fernando; Rosales Lopez, Cesar [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)]. E-mail: magaly.flores@cfe.gob.mx

2011-07-15

.8, sin alterar su produccion de vapor, demostrandose asi que el procedimiento de neutralizacion es factible. Los costos aproximados de las pruebas de neutralizacion realizadas, incluyendo equipos del sistema de neutralizacion propuesto, los gastos del neutralizador (NaOH) y la perforacion del pozo son de unos 71.4 millones de pesos. Se estimo una relacion beneficio/costo de 1.5 y una recuperacion de la inversion, considerando los ingresos por venta de energia a valor presente se obtiene en 5 anos.

Shock wave of vapor-liquid two-phase flow

Institute of Scientific and Technical Information of China (English)

Liangju ZHAO; Fei WANG; Hong GAO; Jingwen TANG; Yuexiang YUAN

2008-01-01

The shock wave of vapor-liquid two-phase flow in a pressure-gain steam injector is studied by build-ing a mathematic model and making calculations. The results show that after the shock, the vapor is nearly com-pletely condensed. The upstream Mach number and the volume ratio of vapor have a great effect on the shock. The pressure and Mach number of two-phase shock con-form to the shock of ideal gas. The analysis of available energy shows that the shock is an irreversible process with entropy increase.

Water vapor movement in freezing aggregate base materials.

Science.gov (United States)

2014-06-01

The objectives of this research were to 1) measure the extent to which water vapor movement results in : water accumulation in freezing base materials; 2) evaluate the effect of soil stabilization on water vapor movement : in freezing base materials;...

Some empirical rules concerning the vapor pressure curve revisited

International Nuclear Information System (INIS)

Velasco, S.; White, J.A.

2014-01-01

Highlights: • A Claussius–Claperyron equation is obtained in the Pitzer corresponding states scheme. • Some well-known empirical rules for the vapor pressure are rewritten in terms of the Pitzer acentric factor. • The Guggenheim point follows the corresponding state scheme better than the normal boiling point. • The Ambrose–Walton vapor pressure equation yields excellent agreement with NIST data in all considered cases. -- Abstract: A form for the Clausius–Clapeyron vapor-pressure equation is obtained in the Pitzer corresponding states scheme. This equation allows one to rewrite the well-known Trouton, Guldberg, van Laar and Guggenheim rules in terms of the acentric factor ω. The original forms of these empirical rules are recovered for some particular values of ω. The proposed rules are checked by analyzing National Institute of Standards and Technology (NIST) data on the liquid-vapor coexistence curve for 105 fluids. These rules have been also analyzed by using the well-known Ambrose–Walton (AW) vapor pressure equation

Pretreated Butterfly Wings for Tuning the Selective Vapor Sensing

Directory of Open Access Journals (Sweden)

Gábor Piszter

2016-09-01

Full Text Available Photonic nanoarchitectures occurring in the scales of Blue butterflies are responsible for their vivid blue wing coloration. These nanoarchitectures are quasi-ordered nanocomposites which are constituted from a chitin matrix with embedded air holes. Therefore, they can act as chemically selective sensors due to their color changes when mixing volatile vapors in the surrounding atmosphere which condensate into the nanoarchitecture through capillary condensation. Using a home-built vapor-mixing setup, the spectral changes caused by the different air + vapor mixtures were efficiently characterized. It was found that the spectral shift is vapor-specific and proportional with the vapor concentration. We showed that the conformal modification of the scale surface by atomic layer deposition and by ethanol pretreatment can significantly alter the optical response and chemical selectivity, which points the way to the efficient production of sensor arrays based on the knowledge obtained through the investigation of modified butterfly wings.

Recommended vapor pressure and thermophysical data for ferrocene

Czech Academy of Sciences Publication Activity Database

Fulem, Michal; Růžička, K.; Červinka, C.; Rocha, M.A.A.; Santos, L.M.N.B.F.; Berg, R.F.

2013-01-01

Roč. 57, FEB (2013), 530-540 ISSN 0021-9614 Institutional support: RVO:68378271 Keywords : ferrocene * vapor pressure * heat capacity * ideal gas thermodynamic properties * sublimation enthalpy * recommended vapor pressure equation Subject RIV: BJ - Thermodynamics Impact factor: 2.423, year: 2013

Analysis of the transient compressible vapor flow in heat pipe

Science.gov (United States)

Jang, Jong Hoon; Faghri, Amir; Chang, Won Soon

1989-01-01

The transient compressible one-dimensional vapor flow dynamics in a heat pipe is modeled. The numerical results are obtained by using the implicit non-iterative Beam-Warming finite difference method. The model is tested for simulated heat pipe vapor flow and actual flow in cylindrical heat pipes. A good comparison of the present transient results for the simulated heat pipe vapor flow with the previous results of a two-dimensional numerical model is achieved and the steady state results are in agreement with the existing experimental data. The transient behavior of the vapor flow under subsonic, sonic, and supersonic speeds and high mass flow rates are successfully predicted. The one-dimensional model also describes the vapor flow dynamics in cylindrical heat pipes at high temperatures.

Vapor and gas sampling of single-shell tank 241-BX-110 using the in situ vapor sampling system

International Nuclear Information System (INIS)

Lockrem, L.L.

1997-01-01

The Vapor Issue Resolution Program tasked the Vapor Team (the team) to collect representative headspace samples from Hanford Site single-shell tank (SST) 241-BX-110. This document presents sampling data resulting from the April 30, 1996 sampling of SST 241-BX-110. Analytical results will be presented in a separate report issued by Pacific Northwest National Laboratory (PNNL), which supplied and analyzed the sampling media

PWFA plasma source - interferometric diagnostics for Li vapor density measurements

International Nuclear Information System (INIS)

Sivakumaran, V.; Mohandas, K.K.; Singh, Sneha; Ravi Kumar, A.V.

2015-01-01

A prototype (40 cm long) plasma source based on Li heat pipe oven has been developed for the Plasma Wakefield Acceleration (PWFA) experiments at IPR (IPR), Gujarat as a part of the ongoing Accelerator Programme. Li vapor in the oven is produced by heating solid Li in helium buffer gas. A uniform column of Li plasma is generated by UV photo ionization (193 nm) of the Li vapor in the heat pipe oven. In these experiments, an accurate measurement of Li vapor density is important as it has got a direct consequence on the plasma electron density. In the present experiment, the vapor density is measured optically by using Hook method (spectrally resolved white light interferometry). The hook like structure formed near the vicinity of the Li 670.8 nm resonance line was recorded with a white light Mach Zehnder interferometer crossed with an imaging spectrograph to estimate the Li vapor density. The vapor density measurements have been carried out as a function of external oven temperature and the He buffer gas pressure. This technique has the advantage of being insensitive to line broadening and line shape, and its high dynamic range even with optically thick absorption line. Here, we present the line integrated Lithium vapor density measurement using Hook method and also compare the same with other optical diagnostic techniques (White light absorption and UV absorption) for Li vapor density measurements. (author)

Evaluación energética de los generadores de vapor F1-2 y BH-109 de una refinería Cubana de petróleo.

Directory of Open Access Journals (Sweden)

Anliet Valles Cruz

2014-03-01

Full Text Available La refinería cubana produce muchos productos para el mercado cubano como los combustibles, aceites, asfaltos y Jet-A1. Los sistemas auxiliares como vapor, aire comprimido y agua se utilizan para la obtención de los productos derivados del petróleo. La generación de vapor es uno de los sistemas auxiliares más importantes dentro de la refinería. La caldera de vapor garantiza que el vapor tenga las condiciones de operación de acuerdo con las normas internacionales. En este trabajo, se realizó la evaluación energética de F1-2 y BH-109 de calderas que utilizan los balances de energía y de masas convencionales. Se obtuvo una eficiencia energética de 61,89 y 77,31 por ciento para F1-2 y BH-109, respectivamente. Las principales pérdidas se debieron al calor sensible de los gases de combustión y a la combustión no química. Para reducir estas pérdidas, mejorar el rendimiento de la caldera y disminuir la temperatura de los gases de salida, se recomienda montar el sistema de control de exceso de aire y volver a examinar o cambiar el sistema de inyección de aire.

Lab-scale tests on ISV vapor transport phenomena

International Nuclear Information System (INIS)

Farnsworth, R.K.; Gardner, B.M.

1996-01-01

In situ vitrification (ISV) is a promising technology for remediating buried waste sites and contaminated soil sites. However, concerns exist that low soil permeabilities may limit vapor transport away from the advancing melt front and cause a melt expulsion that breaches ISV containment. As a result, two ISV lab tests were conducted at the Idaho National Engineering Laboratory (INEL) using INEL soil (permeability: 10 -6 cm/s) and a low permeability (10 -10 cm/s) clay material. The clay test also had a ceramic tube inserted vertically through the center of the area being melted to provide one-dimensional data on vapor transport. Results confirm that low soil permeabilities can limit vapor transport away from the advancing ISV melt front. In addition, peak pressures inside the ceramic tube were significantly greater than those outside the tube, indicating the importance of horizontal vapor transport around the advancing ISV melt front

Improvement of Oil-Vapor Treatment Facility for Wolsong Unit 3,4

International Nuclear Information System (INIS)

Kim, Jeong Guk; Kwon, S. W.; Lee, H. S.

2009-11-01

With the purpose to minimize an oil-vapor discharge to the atmosphere and to be an environmentally friendly nuclear power plant by an improvement of mist eliminator for turbine lubricant system at Wolsong Nuclear Power Plant Unit 3,4, this project - project name : Improvement of Oil-vapor Treatment Facility for Wolsong Unit 3,4 - was conducted for six months (from Apr. 15, 2009 to Oct. 14, 2009). This Project contains Oil-vapor Source and Environmental Regulation, Analysis on the Present Oil-vapor Treatment Facility, Improvement of Oil-vapor Treatment Facility, Test Facility Design, Fabrication, Installation, Test Operation, Evaluation of the Facility

Comparison of sensor characteristics of three real-time monitors for organic vapors.

Science.gov (United States)

Hori, Hajime; Ishimatsu, Sumiyo; Fueta, Yukiko; Hinoue, Mitsuo; Ishidao, Toru

2015-01-01

Sensor characteristics and performance of three real-time monitors for volatile organic compounds (VOC monitor) equipped with a photo ionization detector (PID), a sensor using the interference enhanced reflection (IER) method and a semiconductor gas sensor were investigated for 52 organic solvent vapors designated as class 1 and class 2 of organic solvents by the Ordinance of Organic Solvent Poisoning Prevention in Japan. Test vapors were prepared by injecting each liquid solvent into a 50 l Tedlar® bag and perfectly vaporizing it. The vapor concentration was from one-tenth to twice the administrative control level for all solvents. The vapor concentration was measured with the monitors and a gas chromatograph equipped with a flame ionization detector simultaneously, and the values were compared. The monitor with the PID sensor could measure many organic vapors, but it could not detect some vapors with high ionization potential. The IER sensor could also detect many vapors, but a linear response was not obtained for some vapors. A semiconductor sensor could detect methanol that could not be detected by PID and IER sensors. Working environment measurement of organic vapors by real-time monitors may be possible, but sensor characteristics and their limitations should be known.

Toxicity of vapor phase petroleum contaminants to microbial degrader communities

International Nuclear Information System (INIS)

Long, S.C.; Davey, C.A.

1994-01-01

Petroleum products constitute the largest quantity of synthetic organic chemical products produced in the US. They are comprised of mostly hydrocarbon constituents from many different chemical classes including alkenes, cycloalkanes, aromatic compounds, and polyaromatic hydrocarbons. Many petroleum constituents are classified as volatile organic compounds or VOCs. Petroleum products also constitute a major portion of environmental pollution. One emerging technology, with promise for applications to VOCs in subsurface soil environments, is bioventing coupled with soil vapor extraction. These technologies involve volatilization of contaminants into the soil gas phase by injection and withdrawal of air. This air movement causes enhancement of the aerobic microbial degradation of the mobilized vapors by the indigenous populations. This study investigated the effects of exposure of mixed, subsurface microbial communities to vapor phase petroleum constituents or vapors of petroleum mixtures. Soil slurries were prepared and plated onto mineral salts agar plates and exposed to vapor phase contaminants at equilibrium with pure product. Representative n-alkane, branched alkane, cycloalkane, and aromatic compounds were tested as well as petroleum product mixtures. Vapor exposure altered the numbers and morphologies of the colonies enumerated when compared to controls. However, even at high, equilibrium vapor concentrations, microbial degrader populations were not completely inhibited

Gas Separation Using Organic-Vapor-Resistent Membranes In Conjunctin With Organic-Vapor-Selective Membranes

Science.gov (United States)

Baker, Richard W.; Pinnau, Ingo; He, Zhenjie; Da Costa, Andre R.; Daniels, Ramin; Amo, Karl D.; Wijmans, Johannes G.

2003-06-03

A process for treating a gas mixture containing at least an organic compound gas or vapor and a second gas, such as natural gas, refinery off-gas or air. The process uses two sequential membrane separation steps, one using membrane selective for the organic compound over the second gas, the other selective for the second gas over the organic vapor. The second-gas-selective membranes use a selective layer made from a polymer having repeating units of a fluorinated polymer, and demonstrate good resistance to plasticization by the organic components in the gas mixture under treatment, and good recovery after exposure to liquid aromatic hydrocarbons. The membrane steps can be combined in either order.

Microstructure of vapor deposited coatings on curved substrates

Energy Technology Data Exchange (ETDEWEB)

Rodgers, Theron M.; Zhao, Hengbei; Wadley, Haydn N. G., E-mail: haydn@virginia.edu [Department of Materials Science and Engineering, University of Virginia, 395 McCormick Rd., P.O. Box 400745, Charlottesville, Virginia 22904 (United States)

2015-09-15

Thermal barrier coating systems consisting of a metallic bond coat and ceramic over layer are widely used to extend the life of gas turbine engine components. They are applied using either high-vacuum physical vapor deposition techniques in which vapor atoms rarely experience scattering collisions during propagation to a substrate, or by gas jet assisted (low-vacuum) vapor deposition techniques that utilize scattering from streamlines to enable non-line-of-sight deposition. Both approaches require substrate motion to coat a substrate of complex shape. Here, direct simulation Monte Carlo and kinetic Monte Carlo simulation methods are combined to simulate the deposition of a nickel coating over the concave and convex surfaces of a model airfoil, and the simulation results are compared with those from experimental depositions. The simulation method successfully predicted variations in coating thickness, columnar growth angle, and porosity during both stationary and substrate rotated deposition. It was then used to investigate a wide range of vapor deposition conditions spanning high-vacuum physical vapor deposition to low-vacuum gas jet assisted vapor deposition. The average coating thickness was found to increase initially with gas pressure reaching a maximum at a chamber pressure of 8–10 Pa, but the best coating thickness uniformity was achieved under high vacuum deposition conditions. However, high vacuum conditions increased the variation in the coatings pore volume fraction over the surface of the airfoil. The simulation approach was combined with an optimization algorithm and used to investigate novel deposition concepts to tailor the local coating thickness.

Microstructure of vapor deposited coatings on curved substrates

International Nuclear Information System (INIS)

Rodgers, Theron M.; Zhao, Hengbei; Wadley, Haydn N. G.

2015-01-01

Thermal barrier coating systems consisting of a metallic bond coat and ceramic over layer are widely used to extend the life of gas turbine engine components. They are applied using either high-vacuum physical vapor deposition techniques in which vapor atoms rarely experience scattering collisions during propagation to a substrate, or by gas jet assisted (low-vacuum) vapor deposition techniques that utilize scattering from streamlines to enable non-line-of-sight deposition. Both approaches require substrate motion to coat a substrate of complex shape. Here, direct simulation Monte Carlo and kinetic Monte Carlo simulation methods are combined to simulate the deposition of a nickel coating over the concave and convex surfaces of a model airfoil, and the simulation results are compared with those from experimental depositions. The simulation method successfully predicted variations in coating thickness, columnar growth angle, and porosity during both stationary and substrate rotated deposition. It was then used to investigate a wide range of vapor deposition conditions spanning high-vacuum physical vapor deposition to low-vacuum gas jet assisted vapor deposition. The average coating thickness was found to increase initially with gas pressure reaching a maximum at a chamber pressure of 8–10 Pa, but the best coating thickness uniformity was achieved under high vacuum deposition conditions. However, high vacuum conditions increased the variation in the coatings pore volume fraction over the surface of the airfoil. The simulation approach was combined with an optimization algorithm and used to investigate novel deposition concepts to tailor the local coating thickness

Vacuum distillation/vapor filtration water recovery

Science.gov (United States)

Honegger, R. J.; Neveril, R. B.; Remus, G. A.

1974-01-01

The development and evaluation of a vacuum distillation/vapor filtration (VD/VF) water recovery system are considered. As a functional model, the system converts urine and condensates waste water from six men to potable water on a steady-state basis. The system is designed for 180-day operating durations and for function on the ground, on zero-g aircraft, and in orbit. Preparatory tasks are summarized for conducting low gravity tests of a vacuum distillation/vapor filtration system for recovering water from urine.

Aluminum coating by fluidized bed chemical vapor deposition on austenitic stainless steels AISI 304 and AISI 316

Directory of Open Access Journals (Sweden)

Jose Luddey Marulanda-Arevalo

2015-01-01

Full Text Available Los revestimientos de aluminio f ueron depositados sobre aceros inoxidables AISI 304 y AISI 316 en el rango de temperatura de 5 60 a 600 °C por deposición química de vapor en lecho fluidizado(CVD – FBR. Se utilizó un lecho que consistía en 10 % de aluminio en polvo y 90 % de lecho inerte (alúmina, el cual fue fluidizado con Ar y como ga ses activadores se utilizó una mezcla de ácido clorhídrico con hidrógeno (HCl/H 2 . En el recubrimiento si n tratamiento térmico están las siguiente s especies: Al 13 Fe 4 , Fe 2 Al 5 , FeAl 2 y Al 5 FeNi, las cuales están presentes para ambos aceros. Además, el tratamiento térmico provoca la difusa de alu minio hacia el sustrato y la difusa de hierro del sustrato haci a la superficie del recubrimiento, haciendo la trans formación de los compuestos ant eriores a FeAl, Fe 2 Al 5 , FeAl 2 , Al 0.99 Fe 0.99 Ni 0.02 , AlNi y el Fe 2 AlCr. Se realizó la simulación termodinámica con el s oftware Thermo Calc para obt ener información de la posible composición y la cantidad de mat erial depositado, para condiciones seleccionadas. Las muestras recubi ertas y sin recubrir, se expus ieron a 750 ºC en una atmósfera d onde el vapor agua se transporta a las muestras usando un flujo de N 2 de 40 ml/min, más 100 % vapor de agua (H 2 O. Los dos sustratos sin revestir se comportaron de manera diferente, ya que el acero AISI 304 soportó bien el a taque y ganó poco peso (0.49 mg/cm 2 , en comparación con el acero AISI 316 que perdió mucho peso (25.4 mg/cm 2 . Los aceros recubiertos ganaron poco de peso durante las mil horas de exposición (0.26 mg/cm 2 y soportaron muy bien el ataque corrosivo en c omparación con sustratos sin r ecubrimiento.

Optimum design of vaporizer fin with liquefied natural gas by numerical analysis

International Nuclear Information System (INIS)

Jeong, Hyo Min; Chung, Han Shik; Lee, Sang Chul; Kong, Tae Woo; Yi, Chung Seub

2006-01-01

Generally, the temperature drop under 0 .deg. C on vaporizer surface creates frozen dews. This problem seems to increase as the time progress and humidity rises. In addition, the frozen dews create frost deposition. Consequently, heat transfer on vaporizer decreases because frost deposition causes adiabatic condition. Therefore, it is very important to solve this problem. This paper aims to study of the optimum design of used vaporizer at local LNG station. In this paper, experimental results were compared with numerical results. Geometries of numerical and experimental vaporizers were identical. Studied parameters of vaporizer are angle between two fins (Φ) and fin thickness (TH F ). Numerical analysis results were presented through the correlations between the ice layer thickness (TH ICE ) on the vaporizer surface to the temperature distribution of inside vaporizer (T IN ), fin thickness (TH F ), and angle between two fins (Φ). Numerical result shows good agreement with experimental outcome. Finally, the correlations for optimum design of vaporizer are proposed on this paper

Temperature control of a steam generator by means of an hybrid system PID-RLC; Control de las temperaturas de un generador de vapor mediante un sistema hibrido PID-RLC

Energy Technology Data Exchange (ETDEWEB)

Palomares Gonzalez, Daniel; Garcia Mendoza, Raul [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1991-12-31

A description is made of the design and evaluation of an hybrid control system, formed by a quadratic gaussian linear regulator (QLR) and proportional integral derivative (PID) type regulators. This scheme is used to control the reheater and secondary superheater steam temperatures of a steam generator model with a maximum capacity of 2,150,000 pounds per hour. Once applied to the model of a 300 MW steam power plant, this system showed better results than the traditional schemes and inclusively better than some modern control schemes. This fact characterizes it as a high potential system to be applied to steam power plants. [Espanol] Se describe el diseno y la evaluacion de un sistema de control hibrido, formado por un regulador lineal cuadratico gaussiano (RLC) y reguladores tipo proporcional integral derivativo (PID). Este esquema se utiliza para controlar las temperaturas de vapor del recalentador y sobrecalentador secundario del modelo de un generador de vapor con capacidad maxima de 2,150,000 libras por hora. Una vez aplicado al modelo de una unidad termoelectrica de 300 MW, este sistema produjo mejores resultados que los esquemas tradicionales e incluso mejores que algunos esquemas de control moderno. Esto lo caracteriza como un sistema con un alto potencial para aplicarse a unidades termoelectricas.

Temperature control of a steam generator by means of an hybrid system PID-RLC; Control de las temperaturas de un generador de vapor mediante un sistema hibrido PID-RLC

Energy Technology Data Exchange (ETDEWEB)

Palomares Gonzalez, Daniel; Garcia Mendoza, Raul [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1990-12-31

A description is made of the design and evaluation of an hybrid control system, formed by a quadratic gaussian linear regulator (QLR) and proportional integral derivative (PID) type regulators. This scheme is used to control the reheater and secondary superheater steam temperatures of a steam generator model with a maximum capacity of 2,150,000 pounds per hour. Once applied to the model of a 300 MW steam power plant, this system showed better results than the traditional schemes and inclusively better than some modern control schemes. This fact characterizes it as a high potential system to be applied to steam power plants. [Espanol] Se describe el diseno y la evaluacion de un sistema de control hibrido, formado por un regulador lineal cuadratico gaussiano (RLC) y reguladores tipo proporcional integral derivativo (PID). Este esquema se utiliza para controlar las temperaturas de vapor del recalentador y sobrecalentador secundario del modelo de un generador de vapor con capacidad maxima de 2,150,000 libras por hora. Una vez aplicado al modelo de una unidad termoelectrica de 300 MW, este sistema produjo mejores resultados que los esquemas tradicionales e incluso mejores que algunos esquemas de control moderno. Esto lo caracteriza como un sistema con un alto potencial para aplicarse a unidades termoelectricas.

SIMULACIÓN HORARIA DE UN SISTEMA DE REFRIGERACIÓN COMBINADO EYECTOR-COMPRESIÓN DE VAPOR ASISTIDO POR ENERGÍA SOLAR Y GAS NATURAL HOURLY SIMULATION OF A COMBINED EJECTOR-VAPOR COMPRESSION REFRIGERATION SYSTEM ASSISTED BY SOLAR ENERGY AND NATURAL GAS

Directory of Open Access Journals (Sweden)

Humberto Vidal

2009-04-01

Full Text Available Entre los sistemas de refrigeración movidos térmicamente asistidos por energía solar y gas natural, el sistema de refrigeración con eyector ha recibido especial atención. Este sistema se caracteriza por su simplicidad constructiva, ausencia de partes móviles, operación en bajas temperaturas y bajo costo operacional. Sin embargo, el ciclo de refrigeración por eyector tiene usualmente un bajo coeficiente de desempeño. Una alternativa de solución a este problema lo constituye el sistema de refrigeración con eyector combinado. La primera etapa está constituida por un ciclo de compresión mecánica de vapor convencional con R134a, mientras que la segunda etapa la constituye un ciclo termo-movido con eyector usando R141b como fluido de trabajo. Colectores de placa plana y un quemador de energía auxiliar entregan calor al ciclo de eyector. Este artículo describe la simulación en base horaria de un sistema de refrigeración combinado eyector-compresión de vapor asistido por energía solar y gas natural. El sistema de refrigeración solar combinado es modelado usando la herramienta de simulación TRNSYS-EES y los datos climáticos de un año típico de Florianópolis, Brasil. Los resultados obtenidos con la modelación computacional desarrollada para este sistema muestran la ventaja del ciclo de refrigeración combinado eyector-compresión de vapor por sobre el ciclo simple con eyector. Finalmente, el modelo computacional desarrollado en este artículo podría ser usado para realizar una optimización termo-económica del sistema en trabajos futuros.Among the thermally driven cooling systems assisted by solar energy and natural gas, the ejector cooling system has received special attention. This system is an interesting refrigeration technology due to its construction simplicity, absence of moving parts, operation at lower temperatures and a low operational cost. However, the coefficient of performance of ejector cycle is usually low. The

Thermal plasma chemical vapor deposition

International Nuclear Information System (INIS)

Heberlein, J.; Pfender, E.

1993-01-01

Thermal plasmas, with temperatures up to and even exceeding 10 4 K, are capable of producing high density vapor phase precursors for the deposition of relatively thick films. Although this technology is still in its infancy, it will fill the void between the relatively slow deposition processes such as physical vapor deposition and the high rate thermal spray deposition processes. In this chapter, the present state-of-the-art of this field is reviewed with emphasis on the various types of reactors proposed for this emerging technology. Only applications which attracted particular attention, namely diamond and high T c superconducting film deposition, are discussed in greater detail. (orig.)

A FGGE water vapor wind data set

Science.gov (United States)

Stewart, Tod R.; Hayden, Christopher M.

1985-01-01

It has been recognized for some time that water vapor structure visible in infrared imagery offers a potential for obtaining motion vectors when several images are considered in sequence (Fischer et al., 1981). A study evaluating water vapor winds obtained from the VISSR atmospheric sounder (Stewart et al., 1985) has confirmed the viability of the approach. More recently, 20 data sets have been produced from METEOSAT water vapor imagery for the FGGE period of 10-25 November 1979. Where possible, two data sets were prepared for each day at 0000 and 1200 GMT and compared with rawinsondes over Europe, Africa, and aircraft observations over the oceans. Procedures for obtaining winds were, in general, similar to the earlier study. Motions were detected both by a single pixel tracking and a cross correlation method by using three images individually separated by one hour. A height assignment was determined by matching the measured brightness temperature to the temperature structure represented by the FGGE-IIIB analyses. Results show that the METEOSAT water vapor winds provide uniform horizontal coverage of mid-level flow over the globe with good accuracy.

Uranium/water vapor reactions in gaseous atmospheres

International Nuclear Information System (INIS)

Jackson, R.L.; Condon, J.B.; Steckel, L.M.

1977-07-01

Experiments have been performed to determine the effect of varying humidities, gaseous atmospheres, and temperatures on the uranium/water vapor reaction. A balance, which allowed continuous in-system weighings, was used to determine the rates of the uranium/water vapor reactions at water vapor pressures of 383, 1586, and 2853 Pa and at temperatures of 80, 100, and 150 0 C in atmospheres of hydrogen, argon, or argon/oxygen mixtures. Based on rate data, the reactions were characterized as hydriding or nonhydriding. Hydriding reactions were found to be preferred in moist hydrogen systems at the higher temperatures and the lower humidities. The presence of hydrogen in hydriding systems was found to initially inhibit the reaction, but causes an acceleration of the rate in the final stages. In general, reaction rates of hydriding systems approached the hydriding rates calculated and observed in dry hydrogen. Hydriding and nonhydriding reaction rates showed a positive correlation to temperature and water vapor pressure. Final reaction rates in moist argon/oxygen mixtures of 1.93, 4.57, and 9.08 mole percent oxygen were greater than the rates observed in moist hydrogen or argon. Final reaction rates were negatively correlated to the oxygen concentration

Multicomponent droplet vaporization in a convecting environment

International Nuclear Information System (INIS)

Megaridis, C.M.; Sirignano, W.A.

1990-01-01

In this paper a parametric study of the fundamental exchange processes for energy, mass and momentum between the liquid and gas phases of multicomponent liquid vaporizing droplets is presented. The model, which examines an isolated, vaporizing, multicomponent droplet in an axisymmetric, convecting environment, considers the different volatilities of the liquid components, the alteration of the liquid-phase properties due to the spatial/temporal variations of the species concentrations and also the effects of multicomponent diffusion. In addition, the model accounts for variable thermophysical properties, surface blowing and droplet surface regression due to vaporization, transient droplet heating with internal liquid circulation, and finally droplet deceleration with respect to the free flow due to drag. The numerical calculation employs finite-difference techniques and an iterative solution procedure that provides time-varying spatially-resolved data for both phases. The effects of initial droplet composition, ambient temperature, initial Reynolds number (based on droplet diameter), and volatility differential between the two liquid components are investigated for a liquid droplet consisting of two components with very different volatilities. It is found that mixtures with higher concentration of the less volatile substance actually vaporize faster on account of intrinsically higher liquid heating rates

Gasoline Reid Vapor Pressure

Science.gov (United States)

EPA regulates the vapor pressure of gasoline sold at retail stations during the summer ozone season to reduce evaporative emissions from gasoline that contribute to ground-level ozone and diminish the effects of ozone-related health problems.

Water vapor and Gas Transport through Polymeric Membranes

NARCIS (Netherlands)

Metz, S.J.

2003-01-01

Water vapor transport through polymeric materials plays an important role in a large number of applications such as: food packaging, breathable clothing, roofing membranes, diapers, and the removal of water vapor from gas streams (e.g. dehydration of natural gas or the drying of compressed air).

Vaporization of fault water during seismic slip

Science.gov (United States)

Chen, Jianye; Niemeijer, André R.; Fokker, Peter A.

2017-06-01

Laboratory and numerical studies, as well as field observations, indicate that phase transitions of pore water might be an important process in large earthquakes. We present a model of the thermo-hydro-chemo-mechanical processes, including a two-phase mixture model to incorporate the phase transitions of pore water, occurring during fast slip (i.e., a natural earthquake) in order to investigate the effects of vaporization on the coseismic slip. Using parameters from typical natural faults, our modeling shows that vaporization can indeed occur at the shallow depths of an earthquake, irrespective of the wide variability of the parameters involved (sliding velocity, friction coefficient, gouge permeability and porosity, and shear-induced dilatancy). Due to the fast kinetics, water vaporization can cause a rapid slip weakening even when the hydrological conditions of the fault zone are not favorable for thermal pressurization, e.g., when permeability is high. At the same time, the latent heat associated with the phase transition causes the temperature rise in the slip zone to be buffered. Our parametric analyses reveal that the amount of frictional work is the principal factor controlling the onset and activity of vaporization and that it can easily be achieved in earthquakes. Our study shows that coseismic pore fluid vaporization might have played important roles at shallow depths of large earthquakes by enhancing slip weakening and buffering the temperature rise. The combined effects may provide an alternative explanation for the fact that low-temperature anomalies were measured in the slip zones at shallow depths of large earthquakes.

Drag Reduction by Leidenfrost Vapor Layers

KAUST Repository

Vakarelski, Ivan Uriev

2011-05-23

We demonstrate and quantify a highly effective drag reduction technique that exploits the Leidenfrost effect to create a continuous and robust lubricating vapor layer on the surface of a heated solid sphere moving in a liquid. Using high-speed video, we show that such vapor layers can reduce the hydrodynamic drag by over 85%. These results appear to approach the ultimate limit of drag reduction possible by different methods based on gas-layer lubrication and can stimulate the development of related energy saving technologies.

Performance assessment of the In-Well Vapor-Stripping System

Energy Technology Data Exchange (ETDEWEB)

Gilmore, T.J.; White, M.D.; Spane, F.A. Jr. [and others

1996-10-01

In-well vapor stripping is a remediation technology designed to preferentially extract volatile organic compounds dissolved in groundwater by converting them to a vapor phase and then treating the vapor. This vapor-stripping system is distinctly different from the more traditional in situ air-sparging concept. In situ sparging takes place in the aquifer formation; in-well vapor stripping takes place within the well casing. The system was field demonstrated at Edwards Air Force Base, California; the first-time demonstration of this technology in the United States. Installation and testing of the system were completed in late 1995, and the demonstration was operated nearly continuously for 6 months (191 days) between January 16 and July 25, 1996. Postdemonstration hydrochemical sampling continued until September 1996. The demonstration was conducted by collaborating researchers from Pacific Northwest National Laboratory (a) and Stanford University as part of an interim cleanup action at the base. Edwards Air Force Base and its environmental subcontractor, Earth Technology Corporation, as well as EG&G Environmental, holders of the commercial rights to the technology, were also significant contributors to the demonstration.

Measurement and analysis of transient vaporization in oxide fuel materials

International Nuclear Information System (INIS)

Gorham-Bergeron, E.; Benson, D.A.

1978-01-01

A series of experiments is described in which samples are heated to produce high vapor pressure states in times of 10 -6 to 10 -3 seconds. Experimental measurements of vapor pressures over fresh UO 2 from the pulsed electron beam and pulsed reactor heating tests are presented and compared with other high temperature data. The interpretation of the vapor pressures measured in the tests is discussed in detail. Effects of original sample stoichiometry, chemical interactions with the container and non-equilibrium evaporation due to induced temperature gradients are discussed. Special attention is given to dynamic behavior in rapid heating and vaporization of the oxide due to chemical nonequilibrium. Finally, similar projected reactor experiments on irradiated fuel are described and vapor pressure predictions made using available equilibrium models. A discussion of information accessible from such future tests and its importance is presented

Ammonia IR Absorbance Measurements with an Equilibrium Vapor Cell

National Research Council Canada - National Science Library

Field, Paul

2004-01-01

Infrared (IR) absorbance spectra were acquired for 18 ammonia vapor pressures. The vapor pressures were generated with 15 gravimetrically prepared aqueous solutions and three commercial aqueous solutions using a dynamic method I.E...

Solid vapor pressure for five heavy PAHs via the Knudsen effusion method

International Nuclear Information System (INIS)

Fu Jinxia; Suuberg, Eric M.

2011-01-01

Highlights: → We report on vapor pressures and enthalpies of fusion and sublimation of five heavy PAHs. → Solid vapor pressures were measured using Knudsen effusion method. → Solid vapor pressures for benzo[b]fluoranthene, and indeno[1,2,3-cd]pyrene have not been published in the open literature. → Reported subcooled liquid state vapor pressures may or may not lend themselves to correction to sublimation vapor pressure. → Subcooled liquid state vapor pressures might sometimes actually be closer to actual solid state sublimation vapor pressures. - Abstract: Polycyclic aromatic hydrocarbons (PAHs) are compounds resulting from incomplete combustion and many fuel processing operations, and they are commonly found as subsurface environmental contaminants at sites of former manufactured gas plants. Knowledge of their vapor pressures is the key to predict their fate and transport in the environment. The present study involves five heavy PAHs, i.e. benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[ghi]perylene, indeno[1,2,3-cd]pyrene, and dibenz[a,h]anthracene, which are all as priority pollutants classified by the US EPA. The vapor pressures of these heavy PAHs were measured by using Knudsen effusion method over the temperature range of (364 to 454) K. The corresponding values of the enthalpy of sublimation were calculated from the Clausius-Clapeyron equation. The enthalpy of fusion for the five PAHs was also measured by using differential scanning calorimetry and used to convert earlier published sub-cooled liquid vapor pressure data to solid vapor pressure in order to compare with the present results. These adjusted values do not agree with the present measured actual solid vapor pressure values for these PAHs, but there is good agreement between present results and other earlier published sublimation data.

Review of literature on the asymmetric collapse of vapor bubbles

International Nuclear Information System (INIS)

Fremd, R.; Froehlich, G.

1977-06-01

This report contains a review of literature on the asymmetric collape of vapor bubbles by cavitation with special consideration to vapor explosions. Two numerical models, which describe the collapse of cavities in the neighbourhood of a solid surface, are presented. Moreover experimental results for this case are provided. Propositions to apply the numerical models to vapor explosions are made. (orig.) [de

Apparatus to measure vapor pressure, differential vapor pressure, liquid molar volume, and compressibility of liquids and solutions to the critical point. Vapor pressures, molar volumes, and compressibilities of protiobenzene and deuteriobenzene at elevated temperatures

International Nuclear Information System (INIS)

Kooner, Z.S.; Van Hook, W.A.

1986-01-01

An apparatus designed to measure vapor pressure differences between two similar liquids, such as isotopic isomers, or between a solution and its reference solvent at temperatures and pressures extending to the critical point is described. Vapor-phase volume is minimized and pressure is transmitted to the transducer through the liquid, thereby avoiding several experimental difficulties. Liquid can be injected into the heated part of the system by volumetrically calibrated screw injectors, thus permitting measurements of liquid molar volume, compressibility, and expansivity. The addition of a high-pressure circulating pump and injection valve allows the apparatus to be employed as a continuous dilution differential vapor pressure apparatus for determining partial molar free energies of solution. In the second part of the paper data on the vapor pressure, molar volume, compressibility, and expansivity and their isotope effects for C 6 H 6 and C 6 D 6 from room temperature to near the critical temperature are reported

Importance Profiles for Water Vapor

Science.gov (United States)

Mapes, Brian; Chandra, Arunchandra S.; Kuang, Zhiming; Zuidema, Paquita

2017-11-01

Motivated by the scientific desire to align observations with quantities of physical interest, we survey how scalar importance functions depend on vertically resolved water vapor. Definitions of importance begin from familiar examples of water mass I m and TOA clear-sky outgoing longwave flux I OLR, in order to establish notation and illustrate graphically how the sensitivity profile or "kernel" depends on whether specific humidity S, relative humidity R, or ln( R) are used as measures of vapor. Then, new results on the sensitivity of convective activity I con to vapor (with implied knock-on effects such as weather prediction skill) are presented. In radiative-convective equilibrium, organized (line-like) convection is much more sensitive to moisture than scattered isotropic convection, but it exists in a drier mean state. The lesson for natural convection may be that organized convection is less susceptible to dryness and can survive and propagate into regions unfavorable for disorganized convection. This counterintuitive interpretive conclusion, with respect to the narrow numerical result behind it, highlights the importance of clarity about what is held constant at what values in sensitivity or susceptibility kernels. Finally, the sensitivities of observable radiance signals I sig for passive remote sensing are considered. While the accuracy of R in the lower free troposphere is crucial for the physical importance scalars, this layer is unfortunately the most difficult to isolate with passive remote sensing: In high emissivity channels, water vapor signals come from too high in the atmosphere (for satellites) or too low (for surface radiometers), while low emissivity channels have poor altitude discrimination and (in the case of satellites) are contaminated by surface emissions. For these reasons, active ranging (LiDAR) is the preferred observing strategy.

The tracking of interfaces in an electron-beam vaporizer

International Nuclear Information System (INIS)

Westerberg, K.W.; McClelland, M.A.; Finlayson, B.A.

1993-03-01

A numerical analysis is made of the material and energy flow in an electron beam vaporizer. In this system the energy from an electron beam heats metal confined in a water-cooled crucible. Metal is vaporized from a liquid pool circulating in a shell of its own solid. A modified Galerkin finite element method is used to calculate the flow and temperature fields along with the interface locations. The mesh is parameterized with spines which stretch and pivot as the phase boundaries move. The discretized equations are arranged in an ''arrow'' matrix and solved using the Newton-Raphson method. Results are given for an experimental aluminum vaporizer. The effects of buoyancy and capillary driven flow are included along with the surface contributions of vapor thrust, latent heat, thermal radiation, and crucible contact resistance

Investigation of odd-order nonlinear susceptibilities in atomic vapors

Energy Technology Data Exchange (ETDEWEB)

Yan, Yaqi [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi’an Jiaotong University, Xi’an 710049 (China); Shaanxi Key Laboratory of Information Photonic Technique, Xi’an Jiaotong University, Xi’an 710049 (China); Teaching and Research Section of Maths and Physics, Guangzhou Commanding Academy of Chinese People’s Armed Police Force, Guangzhou, 510440 (China); Wu, Zhenkun; Si, Jinhai; Yan, Lihe; Zhang, Yiqi; Yuan, Chenzhi; Sun, Jia [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi’an Jiaotong University, Xi’an 710049 (China); Shaanxi Key Laboratory of Information Photonic Technique, Xi’an Jiaotong University, Xi’an 710049 (China); Zhang, Yanpeng, E-mail: ypzhang@mail.xjtu.edu.cn [Key Laboratory for Physical Electronics and Devices of the Ministry of Education, Xi’an Jiaotong University, Xi’an 710049 (China); Shaanxi Key Laboratory of Information Photonic Technique, Xi’an Jiaotong University, Xi’an 710049 (China)

2013-06-15

We theoretically deduce the macroscopic symmetry constraints for arbitrary odd-order nonlinear susceptibilities in homogeneous media including atomic vapors for the first time. After theoretically calculating the expressions using a semiclassical method, we demonstrate that the expressions for third- and fifth-order nonlinear susceptibilities for undressed and dressed four- and six-wave mixing (FWM and SWM) in atomic vapors satisfy the macroscopic symmetry constraints. We experimentally demonstrate consistence between the macroscopic symmetry constraints and the semiclassical expressions for atomic vapors by observing polarization control of FWM and SWM processes. The experimental results are in reasonable agreement with our theoretical calculations. -- Highlights: •The macroscopic symmetry constraints are deduced for homogeneous media including atomic vapors. •We demonstrate that odd-order nonlinear susceptibilities satisfy the constraints. •We experimentally demonstrate the deduction in part.

Vaporization and diffusion studies on the stability of doped lanthanum gallates

Energy Technology Data Exchange (ETDEWEB)

Stanislowski, M.; Singheiser, L.; Hilpert, K. [Research Center Juelich, Institute for Materials and Processes in Energy Systems, IWV-2, 52425 Juelich (Germany); Peck, D.H.; Woo, S.K. [Korea Institute of Energy Research, 71-2 Jang-Dong, Yuseong, 305-343 Daejeon (Korea); Schulz, O.; Martin, M. [RWTH Aachen University, Institute of Physical Chemistry, Landoltweg 2, 52056 Aachen (Germany)

2006-07-15

Vaporization and diffusion determine the stability of doped lanthanum gallates under SOFC operating conditions. Systematic vaporization studies of Ga and other elements were carried out using the vapor transpiration method. It was shown that the Ga vaporization is controlled by diffusion from the bulk to the surface. Diffusion coefficients D{sub Ga} and vaporization coefficients {alpha}{sub Ga} were determined by fitting the measured vaporization data to a vaporization model. Secondary phases formed as a result of the vaporization were detected. The influence of different doping levels of Sr, Mg and Fe on the Ga vaporization was elucidated. Moreover, cation self-diffusion of {sup 139}La, {sup 84}Sr and {sup 25}Mg as well as cation impurity diffusion of {sup 144}Nd, {sup 89}Y and {sup 56}Fe in polycrystalline samples of doped lanthanum gallate were directly determined for the composition La{sub 0.9}Sr{sub 0.1}Ga{sub 0.9}Mg{sub 0.1}O{sub 2.9} as an example, from diffusion profiles determined by SIMS. It was found that diffusion occurs by means of bulk and grain boundaries. The bulk diffusion coefficients are similar for all cations with activation energies which are strongly dependent on temperature. The results are explained by a frozen-in defect structure at low temperatures in the ABO{sub 3} perovskite lattice and by proposing a defect cluster containing cation vacancies in the A and B sublattices, as well as oxygen vacancies. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Waste Tank Vapor Characterization Project: Annual status report for FY 1995

International Nuclear Information System (INIS)

Ligotke, M.W.; Fruchter, J.S.; Huckaby, J.L.; Birn, M.B.; McVeety, B.D.; Evans, J.C. Jr.; Pool, K.H.; Silvers, K.L.; Goheen, S.C.

1995-11-01

This report compiles information collected during the Fiscal Year 1995 pertaining to the waste tank vapor characterization project. Information covers the following topics: project management; organic sampling and analysis; inorganic sampling and analysis; waste tank vapor data reports; and the waste tanks vapor database

Computational Fluid Dynamics Model for Saltstone Vault 4 Vapor Space

International Nuclear Information System (INIS)

Lee, Si Young

2005-01-01

Computational fluid dynamics (CFD) methods have been used to estimate the flow patterns for vapor space inside the Saltstone Vault No.4 under different operating scenarios. The purpose of this work is to examine the gas motions inside the vapor space under the current vault configurations. A CFD model took three-dimensional transient momentum-energy coupled approach for the vapor space domain of the vault. The modeling calculations were based on prototypic vault geometry and expected normal operating conditions as defined by Waste Solidification Engineering. The modeling analysis was focused on the air flow patterns near the ventilated corner zones of the vapor space inside the Saltstone vault. The turbulence behavior and natural convection mechanism used in the present model were benchmarked against the literature information and theoretical results. The verified model was applied to the Saltstone vault geometry for the transient assessment of the air flow patterns inside the vapor space of the vault region using the boundary conditions as provided by the customer. The present model considered two cases for the estimations of the flow patterns within the vapor space. One is the reference baseline case. The other is for the negative temperature gradient between the roof inner and top grout surface temperatures intended for the potential bounding condition. The flow patterns of the vapor space calculated by the CFD model demonstrate that the ambient air comes into the vapor space of the vault through the lower-end ventilation hole, and it gets heated up by the Benard-cell type circulation before leaving the vault via the higher-end ventilation hole. The calculated results are consistent with the literature information

Measurement and analysis of transient vaporization in oxide fuel materials

International Nuclear Information System (INIS)

Benson, D.A.; Bergeron, E.G.

1979-01-01

This paper describes a series of experiments in which samples are heated to produce high vapor pressure states in times of 10 -6 to 10 -3 seconds. Experimental measurements of vapor pressures over fresh UO 2 from the pulsed electron beam and pulsed reactor heating tests are presented and compared with other high temperature data. The interpretation of the vapor pressure measured in the tests is discussed in detail. Effects of original sample stoichiometry, chemical interactions with the container and non-equilibrium evaporation due to induced temperature gradients are discussed. Special attention is given to dynamic behavior in rapid heating and vaporization of the oxide due to chemical non-equilibrium. Finally, similar projected reactor experiments on irradiated fuel are described and vapor pressure predictions made using available equilibrium models. A discussion of information accessible from such future tests and its importance is presented. (orig.) [de

Interfacial Dynamics of Condensing Vapor Bubbles in an Ultrasonic Acoustic Field

Science.gov (United States)

Boziuk, Thomas; Smith, Marc; Glezer, Ari

2016-11-01

Enhancement of vapor condensation in quiescent subcooled liquid using ultrasonic actuation is investigated experimentally. The vapor bubbles are formed by direct injection from a pressurized steam reservoir through nozzles of varying characteristic diameters, and are advected within an acoustic field of programmable intensity. While kHz-range acoustic actuation typically couples to capillary instability of the vapor-liquid interface, ultrasonic (MHz-range) actuation leads to the formation of a liquid spout that penetrates into the vapor bubble and significantly increases its surface area and therefore condensation rate. Focusing of the ultrasonic beam along the spout leads to ejection of small-scale droplets from that are propelled towards the vapor liquid interface and result in localized acceleration of the condensation. High-speed video of Schlieren images is used to investigate the effects of the ultrasonic actuation on the thermal boundary layer on the liquid side of the vapor-liquid interface and its effect on the condensation rate, and the liquid motion during condensation is investigated using high-magnification PIV measurements. High-speed image processing is used to assess the effect of the actuation on the dynamics and temporal variation in characteristic scale (and condensation rate) of the vapor bubbles.

Water vapor permeabilities through polymers: diffusivities from experiments and simulations

International Nuclear Information System (INIS)

Seethamraju, Sindhu; Ramamurthy, Praveen Chandrashekarapura; Madras, Giridhar

2014-01-01

This study experimentally determines water vapor permeabilities, which are subsequently correlated with the diffusivities obtained from simulations. Molecular dynamics (MD) simulations were used for determining the diffusion of water vapor in various polymeric systems such as polyethylene, polypropylene, poly (vinyl alcohol), poly (vinyl acetate), poly (vinyl butyral), poly (vinylidene chloride), poly (vinyl chloride) and poly (methyl methacrylate). Cavity ring down spectroscopy (CRDS) based methodology has been used to determine the water vapor transmission rates. These values were then used to calculate the diffusion coefficients for water vapor through these polymers. A comparative analysis is provided for diffusivities calculated from CRDS and MD based results by correlating the free volumes. (paper)

Design and physical features of inductive coaxial copper vapor lasers

Energy Technology Data Exchange (ETDEWEB)

Batenin, V. M. [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation); Kazaryan, M. A. [Russian Academy of Sciences, Lebedev Physical Institute (Russian Federation); Karpukhin, V. T. [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation); Lyabin, N. A. [Istok Research and Production Corporation (Russian Federation); Malikov, M. M., E-mail: mmalikov@oivtran.ru [Russian Academy of Sciences, Joint Institute for High Temperatures (Russian Federation)

2016-11-15

A physical model of a copper vapor laser pumped by a pulse-periodic inductive (electrodeless) discharge is considered. The feasibility of efficient laser pumping by an inductive discharge and reaching high output parameters comparable to those of conventional copper vapor lasers pumped by a longitudinal electrode discharge is demonstrated. The design and physical features of an inductive copper vapor laser with an annular working volume are discussed.

Covering sources of toxic vapors with foam

International Nuclear Information System (INIS)

Aue, W. P.; Guidetti, F.

2009-01-01

In a case of chemical terrorism, first responders might well be confronted with a liquid source of toxic vapor which keeps spreading out its hazardous contents. With foam as an efficient and simple means, such a source could be covered up in seconds and the spread of vapors mitigated drastically. Once covered, the source could then wait for a longer time to be removed carefully and professionally by a decontamination team. In order to find foams useful for covering up toxic vapor sources, a large set of measurements has been performed in order to answer the following questions: - Which foams could be used for this purpose? - How thick should the foam cover be? - For how long would such a foam cover be effective? - Could the practical application of foam cause a spread of the toxic chemical? The toxic vapors sources included GB, GD and HD. Among the foams were 10 fire fighter foams (e.g. AFFF, protein) and the aqueous decontamination foam CASCAD. Small scale experiments showed that CASCAD is best suited for covering a toxic source; a 10 cm layer of it covers and decontaminates GB. The large scale experiments confirmed that any fire fighter foam is a suitable cover for a longer or shorter period.(author)

Tank vapor characterization project - headspace vapor characterization of Hanford Waste Tank 241-C-107: Second comparison study results from samples collected on 3/26/96

International Nuclear Information System (INIS)

Evans, J.C.; Pool, K.H.; Thomas, B.L.

1997-01-01

This report describes the analytical results of vapor samples taken from the headspace of waste storage tank 241-C-107 (Tank C-107) at the Hanford Site in Washington State. The results described in this report is the second in a series comparing vapor sampling of the tank headspace using the Vapor Sampling System (VSS) and In Situ Vapor Sampling (ISVS) system without high efficiency particulate air (HEPA) prefiltration. The results include air concentrations of water (H 2 O) and ammonia (NH 3 ), permanent gases, total non-methane organic compounds (TO-12), and individual organic analytes collected in SUMMA trademark canisters and on triple sorbent traps (TSTs). Samples were collected by Westinghouse Hanford Company (WHC) and analyzed by Pacific Northwest National Laboratory (PNNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Analyte concentrations were based on analytical results and, where appropriate, sample volume measurements provided by WHC

Tank vapor characterization project. Headspace vapor characterization of Hanford waste tank 241-BY-108: Second comparison study results from samples collected on 3/28/96

International Nuclear Information System (INIS)

Thomas, B.L.; Pool, K.H.; Evans, J.C.

1997-01-01

This report describes the analytical results of vapor samples taken from the headspace of waste storage tank 241-BY-108 (Tank BY-108) at the Hanford Site in Washington State. The results described in this report is the second in a series comparing vapor sampling of the tank headspace using the Vapor Sampling System (VSS) and In Situ Vapor Sampling (ISVS) system without high efficiency particulate air (HEPA) prefiltration. The results include air concentrations of water (H 2 O) and ammonia (NH 3 ), permanent gases, total non-methane organic compounds (TO-12), and individual organic analytes collected in SUMMA trademark canisters and on triple sorbent traps (TSTs). Samples were collected by Westinghouse Hanford Company (WHC) and analyzed by Pacific Northwest National Laboratory (PNNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNNL. Analyte concentrations were based on analytical results and, where appropriate, sample volume measurements provided by WHC

Vapor pressures and enthalpies of vaporization of a series of 1- and 2-halogenated naphthalenes

International Nuclear Information System (INIS)

Verevkin, Sergey P.

2003-01-01

Molar enthalpies of vaporization, Δ l g H m 0 , of 1-methyl-naphthalene, 1-chloro-napthalene, 2-chloro-naphthalene, 1-bromo-naphthalene, 2-bromo-naphthalene, and 1-iodo-naphthalene, as well as molar enthalpies of sublimation, Δ s g H m 0 , of 2-chloro-naphthalene and 2-bromo-naphthalene have been obtained from the temperature dependence of the vapor pressure determined with the transpiration method. These values and the correlation gas-chromatography method, based on the Kovat's index, have been used to determine Δ l g H m 0 and Δ s g H m 0 of 2-iodo-naphthalene. Results obtained in this work have been compared with those from the literature and found consistent

Apparatus of vaporizing and condensing liquid radioactive wastes and its operation method

International Nuclear Information System (INIS)

Irie, Hiromitsu; Tajima, Fumio.

1975-01-01

Object: To prevent corrosion of material for a vapor-condenser and a vapor heater and to prevent radioactive contamination of heated vapor. Structure: Liquid waste is fed from a liquid feeding tank to a vapor-condenser to vaporize and condense the waste. Uncondensed liquid waste, which is not in a level of a given density, is temporally stored in a batch tank through a switching valve and a pipe. Prior to successive feeding from the liquid feeding tank, the uncondensed liquid waste within the batch tank is returned by a return pump to the condenser, after which a new liquid is fed from the liquid feeding tank for re-vaporization and condensation in the vapor-condenser. Then, similar operation is repeated until the uncondensed liquid waste assumes a given density, and when the uncondensed liquid waste reaches a given density, the condensed liquid waste is discharged into the storage tank through the switching valve. (Ohara, T.)

Eddy transport of water vapor in the Martian atmosphere

Science.gov (United States)

Murphy, J. R.; Haberle, Robert M.

1993-01-01

Viking orbiter measurements of the Martian atmosphere suggest that the residual north polar water-ice cap is the primary source of atmospheric water vapor, which appears at successively lower northern latitudes as the summer season progresses. Zonally symmetric studies of water vapor transport indicate that the zonal mean meridional circulation is incapable of transporting from north polar regions to low latitudes the quantity of water vapor observed. This result has been interpreted as implying the presence of nonpolar sources of water. Another possibility is the ability of atmospheric wave motions, which are not accounted for in a zonally symmetric framework, to efficiently accomplish the transport from a north polar source to the entirety of the Northern Hemisphere. The ability or inability of the full range of atmospheric motions to accomplish this transport has important implications regarding the questions of water sources and sinks on Mars: if the full spectrum of atmospheric motions proves to be incapable of accomplishing the transport, it strengthens arguments in favor of additional water sources. Preliminary results from a three dimensional atmospheric dynamical/water vapor transport numerical model are presented. The model accounts for the physics of a subliming water-ice cap, but does not yet incorporate recondensation of this sublimed water. Transport of vapor away from this water-ice cap in this three dimensional framework is compared with previously obtained zonally symmetric (two dimensional) results to quantify effects of water vapor transport by atmospheric eddies.

Effects of molten material temperatures and coolant temperatures on vapor explosion

Institute of Scientific and Technical Information of China (English)

LI Tianshu; YANG Yanhua; YUAN Minghao; HU Zhihua

2007-01-01

An observable experiment facility for low-temperature molten materials to be dropped into water was set up in this study to investigate the mechanism of the vapor explosion. The effect of the fuel and coolant interaction(FCI) on the vapor explosion during the severe accidents of a fission nuclear reactor has been studied. The experiment results showed that the molten material temperature has an important effect on the vapor explosion behavior and pressure. The increase of the coolant temperature would decrease the pressure of the vapor explosion.

Atmospheric water vapor: Distribution and Empirical estimation in the atmosphere of Thailand

Science.gov (United States)

Phokate, S.

2017-09-01

Atmospheric water vapor is a crucial component of the Earth’s atmosphere, which is shown by precipitable water vapor. It is calculated from the upper air data. In Thailand, the data were collected from four measuring stations located in Chiang Mai, Ubon Ratchathani, Bangkok, and Songkhla during the years 1998-2013. The precipitable water vapor obtained from this investigation were used to define an empirical model associated with the vapor pressure, which is a surface data at the same stations. The result shows that the relationship has a relatively high level of reliability. The precipitable water vapor obtained from the upper air data is nearly equal to the value from the model. The model was used to calculate the precipitable water vapor from the surface data 85 stations across the country. The result shows that seasonal change of the precipitable water vapor was low in the dry season (November-April) and high in the rainy season (May-October). In addition, precipitable water vapor varies along the latitudes of the stations. The high value obtains for low latitudes, but it is low for high latitudes.

Combined rankine and vapor compression cycles

Science.gov (United States)

Radcliff, Thomas D.; Biederman, Bruce P.; Brasz, Joost J.

2005-04-19

An organic rankine cycle system is combined with a vapor compression cycle system with the turbine generator of the organic rankine cycle generating the power necessary to operate the motor of the refrigerant compressor. The vapor compression cycle is applied with its evaporator cooling the inlet air into a gas turbine, and the organic rankine cycle is applied to receive heat from a gas turbine exhaust to heat its boiler within one embodiment, a common condenser is used for the organic rankine cycle and the vapor compression cycle, with a common refrigerant, R-245a being circulated within both systems. In another embodiment, the turbine driven generator has a common shaft connected to the compressor to thereby eliminate the need for a separate motor to drive the compressor. In another embodiment, an organic rankine cycle system is applied to an internal combustion engine to cool the fluids thereof, and the turbo charged air is cooled first by the organic rankine cycle system and then by an air conditioner prior to passing into the intake of the engine.

Physical Vapor Deposition of Thin Films

Science.gov (United States)

Mahan, John E.

2000-01-01

A unified treatment of the theories, data, and technologies underlying physical vapor deposition methods With electronic, optical, and magnetic coating technologies increasingly dominating manufacturing in the high-tech industries, there is a growing need for expertise in physical vapor deposition of thin films. This important new work provides researchers and engineers in this field with the information they need to tackle thin film processes in the real world. Presenting a cohesive, thoroughly developed treatment of both fundamental and applied topics, Physical Vapor Deposition of Thin Films incorporates many critical results from across the literature as it imparts a working knowledge of a variety of present-day techniques. Numerous worked examples, extensive references, and more than 100 illustrations and photographs accompany coverage of: * Thermal evaporation, sputtering, and pulsed laser deposition techniques * Key theories and phenomena, including the kinetic theory of gases, adsorption and condensation, high-vacuum pumping dynamics, and sputtering discharges * Trends in sputter yield data and a new simplified collisional model of sputter yield for pure element targets * Quantitative models for film deposition rate, thickness profiles, and thermalization of the sputtered beam

Measurement of vapor behavior in tight-lattice bundles by neutron radiography

International Nuclear Information System (INIS)

Kureta, Masatoshi; Akimoto, Hajime

2004-01-01

Three-dimensional and instantaneous void fractions in tight-lattice 7-rod and 14-rod bundles were measured by neutron radiography in order to make clear the flow behavior and to verify the advanced fine-mesh numerical analysis codes for the R and D of the Reduced-Moderation Water Reactors (RMWR). Time-averaged 3D void fraction distribution is evaluated with the spatial resolution of 0.1 - 0.2 mm using neutron tomography, and consecutive change of vapor behavior is observed quantitatively with time step of 1 ms using high-frame-rate neutron radiography (HFR-NR). In this paper, void fraction distribution and vapor behavior of flow boiling of water in tight-lattice rod bundles are focused on and discussed based on the obtained results. 'High void fraction spot', 'void drift phenomenon', and 'vapor chimney' were observed under atmospheric pressure conditions. Here, 'high void fraction spot' indicates that high void fraction regions are appeared between adjacent rods, narrow space, at/near point of net vapor generation region. 'Void drift' and 'vapor chimney' represent that high void fraction region moves to wide triangular space and is formed a vapor flow channel so-called 'vapor chimney'. It was confirmed from the time-averaged 3D data that void fraction in the center is higher than that in the periphery. On the other hand, it was found from the HFR-NR experiments that big vapor bubbles and/or cluster flow upward intermittently not only in the center but in the periphery of the channel and, therefore, point of net vapor generation is scattered statistically in wide region. (author)

Improved waste water vapor compression distillation technology. [for Spacelab

Science.gov (United States)

Johnson, K. L.; Nuccio, P. P.; Reveley, W. F.

1977-01-01

The vapor compression distillation process is a method of recovering potable water from crewman urine in a manned spacecraft or space station. A description is presented of the research and development approach to the solution of the various problems encountered with previous vapor compression distillation units. The design solutions considered are incorporated in the preliminary design of a vapor compression distillation subsystem. The new design concepts are available for integration in the next generation of support systems and, particularly, the regenerative life support evaluation intended for project Spacelab.

Numerical simulation of superheated vapor bubble rising in stagnant liquid

Science.gov (United States)

Samkhaniani, N.; Ansari, M. R.

2017-09-01

In present study, the rising of superheated vapor bubble in saturated liquid is simulated using volume of fluid method in OpenFOAM cfd package. The surface tension between vapor-liquid phases is considered using continuous surface force method. In order to reduce spurious current near interface, Lafaurie smoothing filter is applied to improve curvature calculation. Phase change is considered using Tanasawa mass transfer model. The variation of saturation temperature in vapor bubble with local pressure is considered with simplified Clausius-Clapeyron relation. The couple velocity-pressure equation is solved using PISO algorithm. The numerical model is validated with: (1) isothermal bubble rising and (2) one-dimensional horizontal film condensation. Then, the shape and life time history of single superheated vapor bubble are investigated. The present numerical study shows vapor bubble in saturated liquid undergoes boiling and condensation. It indicates bubble life time is nearly linear proportional with bubble size and superheat temperature.

27 CFR 19.821 - Production of vinegar by the vaporizing process.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Production of vinegar by the vaporizing process. 19.821 Section 19.821 Alcohol, Tobacco Products and Firearms ALCOHOL AND... Vinegar by the Vaporizing Process Scope of Subpart § 19.821 Production of vinegar by the vaporizing...

Evaluación de la retrogradación del almidón en harina de yuca precocida

OpenAIRE

Rodríguez Sandoval, Eduardo; Sandoval Aldana, Angélica; Fernández Quintero, Alejandro

2008-01-01

Las modificaciones del almidón, que ocurren durante el proceso de elaboración de harina de yuca precocida, se evaluaron utilizando técnicas como calorimetría diferencial de barrido (CDB), difracción de rayos X, comportamiento al empastamiento y capacidad de formación de complejo con yodo. La harina precocida se obtuvo a partir de trozos de parénquima de yuca cocinados en vapor o en agua a ebullición, los cuales fueron posteriormente alma...

Chemically assisted release of transition metals in graphite vaporizers for atomic spectrometry

International Nuclear Information System (INIS)

Katskov, Dmitri; Darangwa, Nicholas; Grotti, Marco

2006-01-01

The processes associated with the vaporization of microgram samples and modifiers in a graphite tube ET AAS were investigated by the example of transition metals. The vapor absorption spectra and vaporization behavior of μg-amounts Cd, Zn, Cu, Ag, Au, Ni, Co, Fe, Mn and Cr were studied using the UV spectrometer with CCD detector, coupled with a continuum radiation source. The pyrocoated, Ta or W lined tubes, with Ar or He as internal gases, and filter furnace were employed in the comparative experiments. It was found that the kinetics of atomic vapor release changed depending on the specific metal-substrate-gas combination; fast vaporization at the beginning was followed by slower 'tailing.' The absorption continuum, overlapped by black body radiation at longer wavelengths, accompanied the fast vaporization mode for all metals, except Cd and Zn. The highest intensity of the continuum was observed in the pyrocoated tube with Ar. For Cu and Ag the molecular bands overlapped the absorption continuum; the continuum and bands were suppressed in the filter furnace. It is concluded that the exothermal interaction of sample vapor with the material of the tube causes the energy evolution in the gas phase. The emitted heat is dispersed near the tube wall in the protective gas and partially transferred back to the surface of the sample, thus facilitating the vaporization. The increased vapor flow causes over-saturation and gas-phase condensation in the absorption volume at some distance from the wall, where the gas temperature is not affected by the reaction. The condensation is accompanied by the release of phase transition energy via black body radiation and atomic emission. The particles of condensate and molecular clusters cause the scattering of light and molecular absorption; slow decomposition of the products of the sample vapor-substrate reaction produces the 'tailing' of atomic absorption signal. The interaction of graphite with metal vapor or oxygen, formed in the

Vapor liquid fraction determination

International Nuclear Information System (INIS)

1980-01-01

This invention describes a method of measuring liquid and vapor fractions in a non-homogeneous fluid flowing through an elongate conduit, such as may be required with boiling water, non-boiling turbulent flows, fluidized bed experiments, water-gas mixing analysis, and nuclear plant cooling. (UK)

Failure problems in superheater spacers of steam generators; Problematica de fallas en espaciadores de sobrecalentadores de generadores de vapor

Energy Technology Data Exchange (ETDEWEB)

Chacon Nava, Jose G; Martinez Villafane, Alberto [Instituto de Investigaciones Electricas, Cuernavaca (Mexico); Fuentes Samaniego, Raul [Universidad Autonoma de Nuevo Leon (Mexico); Mojica Calderon, Cecilio [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1988-12-31

In this article the general aspects of the steam generator superheater fixed spacers failures are analyzed, emphasis is made on the influence several aspects such as the operation of the unit have, the appropriate execution of welds and the selection of binding materials. Likewise several recommendations are made to bring the failures to a minimum. [Espanol] En este articulo se analizan aspectos generales de fallas en espaciadores fijos de sobrecalentadores de generadores de vapor, y se hace hincapie en la influencia que tienen diversos aspectos tales como la operacion de la unidad, la adecuada ejecucion de soldaduras y la seleccion del material de aporte. Asimismo, se proponen algunas recomendaciones para reducir al minimo las fallas.

Evaluación agroindustrial de los aceites esenciales de Artemisia dracunculos L, Franseria artemisioides Willd, Salvia officinalis L, Lippia dulcis Frev, y Occimun americanum L en condiciones del Valle del Cauca

Directory of Open Access Journals (Sweden)

Sánchez Orozco Manuel Salvador

2010-09-01

Full Text Available

En parcelas establecidas de la Colección de Trabajo de Plantas Medicinales del Centro Experimental CEUNP en condiciones del departamento del Valle del Cauca, se tomaron muestras del material vegetal mediante el corte manual en un marco de 0.25m² ; se separaron hojas, tallos y flores de cada especie. Se determinó el porcentaje de materia seca y se acondicionó para el proceso de extracción de aceite esencial mediante arrastre con vapor. A los aceites obtenidos se les midió la densidad, y el índice de refracción, y al de mayor rendimiento en cada especie se le determinó la composición química mediante cromatografía de gases acoplada a masas.

Evaluación agroindustrial de los aceites esenciales de Artemisia dracunculos L, Franseria artemisioides Willd, Salvia officinalis L, Lippia dulcis Frev, y Occimun americanum L en condiciones del Valle del Cauca

Directory of Open Access Journals (Sweden)

Luis F Saldarriaga C

2010-07-01

Full Text Available En parcelas establecidas de la Colección de Trabajo de Plantas Medicinales del Centro Experimental CEUNP en condiciones del departamento del Valle del Cauca, se tomaron muestras del material vegetal mediante el corte manual en un marco de 0.25m² ; se separaron hojas, tallos y flores de cada especie. Se determinó el porcentaje de materia seca y se acondicionó para el proceso de extracción de aceite esencial mediante arrastre con vapor. A los aceites obtenidos se les midió la densidad, y el índice de refracción, y al de mayor rendimiento en cada especie se le determinó la composición química mediante cromatografía de gases acoplada a masas. Los mayores rendimientos de aceite esencial se presentaron en las hojas de las cinco especies; los compuestos químicos más representativos fueron Elemicina (40.11% en Estragón, el b-Himachaleno (53.98% en Altamisa, trans-b-Cariofileno (22.18 en Salvia Roja, a-Bisabolol (15.79% en Orozúl y 1,8- Cineol (Eucaliptol (23.34% en Albahaca. Las propiedades físicas fueron coherentes con la presencia de los compuestos químicos encontrados. Todos los aceites esenciales presentan potenciales usos agroindustriales, que varían de acuerdo con la especie y con sus componentes, desde usos en el sector de fragancias, cosmético, medicinal, alimenticio, hasta usos en el sector agrícola.

Removal of hydrogen sulfide as ammonium sulfate from hydropyrolysis product vapors

Energy Technology Data Exchange (ETDEWEB)

Marker, Terry L.; Felix, Larry G.; Linck, Martin B.; Roberts, Michael J.

2017-03-14

A system and method for processing biomass into hydrocarbon fuels that includes processing a biomass in a hydropyrolysis reactor resulting in hydrocarbon fuels and a process vapor stream and cooling the process vapor stream to a condensation temperature resulting in an aqueous stream. The aqueous stream is sent to a catalytic reactor where it is oxidized to obtain a product stream containing ammonia and ammonium sulfate. A resulting cooled product vapor stream includes non-condensable process vapors comprising H.sub.2, CH.sub.4, CO, CO.sub.2, ammonia and hydrogen sulfide.

Removal of hydrogen sulfide as ammonium sulfate from hydropyrolysis product vapors

Science.gov (United States)

Marker, Terry L; Felix, Larry G; Linck, Martin B; Roberts, Michael J

2014-10-14

A system and method for processing biomass into hydrocarbon fuels that includes processing a biomass in a hydropyrolysis reactor resulting in hydrocarbon fuels and a process vapor stream and cooling the process vapor stream to a condensation temperature resulting in an aqueous stream. The aqueous stream is sent to a catalytic reactor where it is oxidized to obtain a product stream containing ammonia and ammonium sulfate. A resulting cooled product vapor stream includes non-condensable process vapors comprising H.sub.2, CH.sub.4, CO, CO.sub.2, ammonia and hydrogen sulfide.

Development of halide copper vapor laser (the characteristics of using Cul)

International Nuclear Information System (INIS)

Oouti, Kazumi; Wada, Yukio; Sasao, Nobuyuki

1990-01-01

We are developing halide copper vapor laser that is high efficiency and high reputation rate visible laser. Halide copper vapor laser uses halide copper of copper vapor source. It melts low temperature in comporison with metal copper, because laser tube structure is very simple and it can operate easy. This time, we experiment to use Cul for copper vapor source. We resulted maximum output energy 17.8 (W) and maximum efficiency 0.78 (%) when operate condition was reputation rate 30 (kHz), gas pressure 90 (Torr), charging voltage 13 (kV). (author)

The role of fragmentation mechanism in large-scale vapor explosions

International Nuclear Information System (INIS)

Liu, Jie

2003-01-01

A non-equilibrium, multi-phase, multi-component code PROVER-I is developed for propagation phase of vapor explosion. Two fragmentation models are used. The hydrodynamic fragmentation model is the same as Fletcher's one. A new thermal fragmentation model is proposed with three kinds of time scale for modeling instant fragmentation, spontaneous nucleation fragmentation and normal boiling fragmentation. The role of fragmentation mechanisms is investigated by the simulations of the pressure wave propagation and energy conversion ratio of ex-vessel vapor explosion. The spontaneous nucleation fragmentation results in a much higher pressure peak and a larger energy conversion ratio than hydrodynamic fragmentation. The instant fragmentation gives a slightly larger energy conversion ratio than spontaneous nucleation fragmentation, and the normal boiling fragmentation results in a smaller energy conversion ratio. The detailed analysis of the structure of pressure wave makes it clear that thermal detonation exists only under the thermal fragmentation circumstance. The high energy conversion ratio is obtained in a small vapor volume fraction. However, in larger vapor volume fraction conditions, the vapor explosion is weak. In a large-scale vapor explosion, the hydrodynamic fragmentation is essential when the pressure wave becomes strong, so a small energy conversion ratio is expected. (author)

An exposure system for measuring nasal and lung uptake of vapors in rats

Energy Technology Data Exchange (ETDEWEB)

Dahl, A.R.; Brookins, L.K.; Gerde, P. [National Inst. for Working Life, Solna (Sweden)

1995-12-01

Inhaled gases and vapors often produce biological damage in the nasal cavity and lower respiratory tract. The specific site within the respirator tract at which a gas or vapor is absorbed strongly influences the tissues at risk to potential toxic effects; to predict or to explain tissue or cell specific toxicity of inhaled gases or vapors, the sites at which they are absorbed must be known. The purpose of the work reported here was to develop a system for determining nose and lung absorption of vapors in rats, an animal commonly used in inhalation toxicity studies. In summary, the exposure system described allows us to measure in the rate: (1) nasal absorption and desorption of vapors; (2) net lung uptake of vapors; and (3) the effects of changed breathing parameters on vapor uptake.

Nuclear system vaporization

International Nuclear Information System (INIS)

Bougault, R.; Brou, R.; Colin, J.; Cussol, D.; Durand, D.; Le Brun, C.; Lecolley, J.F.; Lopez, O.; Louvel, M.; Nakagawa, T.; Peter, J.; Regimbart, R.; Steckmeyer, J.C.; Tamain, B.; Vient, E.; Yuasa-Nakagawa, K.; Wieloch, A.

1998-01-01

A particular case of the hot nuclei de-excitation is the total nuclear dislocation into light particles (n, p, d, t, 3 He and α). Such events were first observed at bombarding energies lower than 100 MeV/nucleon due to high detection performances of the INDRA multidetector. The light system Ar + Ni was studied at several bombarding energies ranging from 32 to 95 MeV/nucleon. The events associated to a total vaporization of the system occur above the energy threshold of ∼ 50 MeV/nucleon. A study of the form of these events shows that we have essentially two sources. The excitation energy of these sources may be determined by means of the kinematic properties of their de-excitation products. A preliminary study results in excitation energy values of the order 10 - 14 MeV/nucleon. The theoretical calculation based on a statistical model modified to take into account high excitation energies and excited levels in the lightest nuclei predicts that the vaporization of the two partner nuclei in the Ar + Ni system takes place when the excitation energy exceeds 12 MeV/nucleon what is qualitatively in agreement with the values deduced from calorimetric analysis

Laser vapor phase deposition of semiconductors

Energy Technology Data Exchange (ETDEWEB)

Karlov, N.V.; Luk' ianchuk, B.S.; Sisakian, E.V.; Shafeev, G.A.

1987-06-01

The pyrolytic effect of IR laser radiation is investigated with reference to the initiation and control of the vapor phase deposition of semiconductor films. By selecting the gas mixture composition and laser emission parameters, it is possible to control the deposition and crystal formation processes on the surface of semiconductors, with the main control action achieved due to the nonadiabatic kinetics of reactions in the gas phase and high temperatures in the laser heating zone. This control mechanism is demonstrated experimentally during the laser vapor deposition of germanium and silicon films from tetrachlorides on single-crystal Si and Ge substrates. 5 references.

The vaporization enthalpies and vapor pressures of fatty acid methyl esters C18, C21 to C23, and C25 to C29 by correlation - gas chromatography

International Nuclear Information System (INIS)

Chickos, James S.; Zhao Hui; Nichols, Gary

2004-01-01

Vapor pressures and vaporization enthalpies for methyl heptadecanoate and methyl heneicosanoate to methyl octacosanoate exclusive of methyl tricosanoate are evaluated as a function of temperature over the temperature range T = 298.15-450 K by correlation gas chromatography. The results are generated by an extrapolative process using literature values for methyl tetradecanoate to methyl eicosanoate as standards. Relationships for calculating vapor pressures of the title compounds from T = 298.15 to 450 K are provided. Experimental fusion enthalpies are also reported for the methyl esters from methyl hexadecanoate to methyl octacosanoate excluding methyl tridecanoate. Vaporization enthalpies and fusion enthalpies adjusted for temperature to T = 298.15 K are combined to provide sublimation enthalpies. The results are compared to available literature values. A rationale for the linear relationship observed between enthalpies of vaporization and enthalpies of transfer from solution to the vapor is also provided

Monolithic microwave integrated circuit water vapor radiometer

Science.gov (United States)

Sukamto, L. M.; Cooley, T. W.; Janssen, M. A.; Parks, G. S.

1991-01-01

A proof of concept Monolithic Microwave Integrated Circuit (MMIC) Water Vapor Radiometer (WVR) is under development at the Jet Propulsion Laboratory (JPL). WVR's are used to remotely sense water vapor and cloud liquid water in the atmosphere and are valuable for meteorological applications as well as for determination of signal path delays due to water vapor in the atmosphere. The high cost and large size of existing WVR instruments motivate the development of miniature MMIC WVR's, which have great potential for low cost mass production. The miniaturization of WVR components allows large scale deployment of WVR's for Earth environment and meteorological applications. Small WVR's can also result in improved thermal stability, resulting in improved calibration stability. Described here is the design and fabrication of a 31.4 GHz MMIC radiometer as one channel of a thermally stable WVR as a means of assessing MMIC technology feasibility.

Stability limit of liquid water in metastable equilibrium with subsaturated vapors.

Science.gov (United States)

Wheeler, Tobias D; Stroock, Abraham D

2009-07-07

A pure liquid can reach metastable equilibrium with its subsaturated vapor across an appropriate membrane. This situation is analogous to osmotic equilibrium: the reduced chemical potential of the dilute phase (the subsaturated vapor) is compensated by a difference in pressure between the phases. To equilibrate with subsaturated vapor, the liquid phase assumes a pressure that is lower than its standard vapor pressure, such that the liquid phase is metastable with respect to the vapor phase. For sufficiently subsaturated vapors, the liquid phase can even assume negative pressures. The appropriate membrane for this metastable equilibrium must provide the necessary mechanical support to sustain the difference in pressure between the two phases, limit nonhomogeneous mechanisms of cavitation, and resist the entry of the dilutant (gases) into the pure phase (liquid). In this article, we present a study of the limit of stability of liquid water--the degree of subsaturation at which the liquid cavitates--in this metastable state within microscale voids embedded in hydrogel membranes. We refer to these structures as vapor-coupled voids (VCVs). In these VCVs, we observed that liquid water cavitated when placed in equilibrium with vapors of activity aw,vapairhumiditynucleation theory or molecular simulations (Pcav=-140 to -180 MPa). To determine the cause of the disparity between the observed and predicted stability limit, we examine experimentally the likelihood of several nonhomogeneous mechanisms of nucleation: (i) heterogeneous nucleation caused by hydrophobic patches on void walls, (ii) nucleation caused by the presence of dissolved solute, (iii) nucleation caused by the presence of pre-existing vapor nuclei, and (iv) invasion of air through the hydrogel membrane into the voids. We conclude that, of these possibilities, (i) and (ii) cannot be discounted, whereas (iii) and (iv) are unlikely to play a role in determining the stability limit.

Relationships between fusion, solution, vaporization and sublimation enthalpies of substituted phenols

International Nuclear Information System (INIS)

Yagofarov, Mikhail I.; Nagrimanov, Ruslan N.; Solomonov, Boris N.

2017-01-01

Highlights: • Method for determination of sublimation and vaporization enthalpies of phenols was developed. • Vaporization enthalpies of 28 phenols at 298 K were calculated. • Sublimation enthalpies of 26 phenols at 298 K were calculated using fusion enthalpies at melting temperatures. • Obtained values are in good agreement with the results of conventional methods. - Abstract: In this work a method for determination of sublimation and vaporization enthalpies of substituted phenols was developed. This method is a modification of solution calorimetry approach. Modification is based on the novel relations, which bind solution, vaporization and sublimation enthalpies at 298.15 K and fusion enthalpy at the melting temperature. According to novel relations the equations for calculating sublimation and vaporization enthalpies at 298.15 K were offered. Calculated values of sublimation and vaporization enthalpies of phenol derivatives containing alkyls, halogens, –OCH 3 , –NO 2 , –COCH 3 , –COOCH 3 groups, and dihydroxybenzenes were compared with literature data (298.15 K) obtained by conventional methods. In most of the cases divergence does not exceed 2–3%.

The annual cycle of stratospheric water vapor in a general circulation model

Science.gov (United States)

Mote, Philip W.

1995-01-01

The application of general circulation models (GCM's) to stratospheric chemistry and transport both permits and requires a thorough investigation of stratospheric water vapor. The National Center for Atmospheric Research has redesigned its GCM, the Community Climate Model (CCM2), to enable studies of the chemistry and transport of tracers including water vapor; the importance of water vapor to the climate and chemistry of the stratosphere requires that it be better understood in the atmosphere and well represented in the model. In this study, methane is carried as a tracer and converted to water; this simple chemistry provides an adequate representation of the upper stratospheric water vapor source. The cold temperature bias in the winter polar stratosphere, which the CCM2 shares with other GCM's, produces excessive dehydration in the southern hemisphere, but this dry bias can be ameliorated by setting a minimum vapor pressure. The CCM2's water vapor distribution and seasonality compare favorably with observations in many respects, though seasonal variations including the upper stratospheric semiannual oscillation are generally too small. Southern polar dehydration affects midlatitude water vapor mixing ratios by a few tenths of a part per million, mostly after the demise of the vortex. The annual cycle of water vapor in the tropical and northern midlatitude lower stratosphere is dominated by drying at the tropical tropopause. Water vapor has a longer adjustment time than methane and had not reached equilibrium at the end of the 9 years simulated here.

Hybrid Vapor Stripping-Vapor Permeation Process for Recovery and Dehydration of 1-Butanol and Acetone/Butanol/Ethanol from Dilute Aqueous Solutions. Part 2. Experimental Validation with Simple Mixtures and Actual Fermentation Broth

Science.gov (United States)

BACKGROUND: In Part1 of this work, a process integrating vapor stripping, vapor compression, and a vapor permeation membrane separation step, Membrane Assisted Vapor Stripping (MAVS), was predicted to produce energy savings compared to traditional distillation systems for separat...

Removal of gasoline vapors from air streams by biofiltration

Energy Technology Data Exchange (ETDEWEB)

Apel, W.A.; Kant, W.D.; Colwell, F.S.; Singleton, B.; Lee, B.D.; Andrews, G.F.; Espinosa, A.M.; Johnson, E.G.

1993-03-01

Research was performed to develop a biofilter for the biodegradation of gasoline vapors. The overall goal of this effort was to provide information necessary for the design, construction, and operation of a commercial gasoline vapor biofilter. Experimental results indicated that relatively high amounts of gasoline vapor adsorption occur during initial exposure of the biofilter bed medium to gasoline vapors. Biological removal occurs over a 22 to 40{degrees}C temperature range with removal being completely inhibited at 54{degrees}C. The addition of fertilizer to the relatively fresh bed medium used did not increase the rates of gasoline removal in short term experiments. Microbiological analyses indicated that high levels of gasoline degrading microbes are naturally present in the bed medium and that additional inoculation with hydrocarbon degrading cultures does not appreciably increase gasoline removal rates. At lower gasoline concentrations, the vapor removal rates were considerably lower than those at higher gasoline concentrations. This implies that system designs facilitating gasoline transport to the micro-organisms could substantially increase gasoline removal rates at lower gasoline vapor concentrations. Test results from a field scale prototype biofiltration system showed volumetric productivity (i.e., average rate of gasoline degradation per unit bed volume) values that were consistent with those obtained with laboratory column biofilters at similar inlet gasoline concentrations. In addition, total benzene, toluene, ethyl-benzene, and xylene (BTEX) removal over the operating conditions employed was 50 to 55%. Removal of benzene was approximately 10 to 15% and removal of the other members of the BTEX group was much higher, typically >80%.

Removal of gasoline vapors from air streams by biofiltration

Energy Technology Data Exchange (ETDEWEB)

Apel, W.A.; Kant, W.D.; Colwell, F.S.; Singleton, B.; Lee, B.D.; Andrews, G.F.; Espinosa, A.M.; Johnson, E.G.

1993-03-01

Research was performed to develop a biofilter for the biodegradation of gasoline vapors. The overall goal of this effort was to provide information necessary for the design, construction, and operation of a commercial gasoline vapor biofilter. Experimental results indicated that relatively high amounts of gasoline vapor adsorption occur during initial exposure of the biofilter bed medium to gasoline vapors. Biological removal occurs over a 22 to 40[degrees]C temperature range with removal being completely inhibited at 54[degrees]C. The addition of fertilizer to the relatively fresh bed medium used did not increase the rates of gasoline removal in short term experiments. Microbiological analyses indicated that high levels of gasoline degrading microbes are naturally present in the bed medium and that additional inoculation with hydrocarbon degrading cultures does not appreciably increase gasoline removal rates. At lower gasoline concentrations, the vapor removal rates were considerably lower than those at higher gasoline concentrations. This implies that system designs facilitating gasoline transport to the micro-organisms could substantially increase gasoline removal rates at lower gasoline vapor concentrations. Test results from a field scale prototype biofiltration system showed volumetric productivity (i.e., average rate of gasoline degradation per unit bed volume) values that were consistent with those obtained with laboratory column biofilters at similar inlet gasoline concentrations. In addition, total benzene, toluene, ethyl-benzene, and xylene (BTEX) removal over the operating conditions employed was 50 to 55%. Removal of benzene was approximately 10 to 15% and removal of the other members of the BTEX group was much higher, typically >80%.

Constrained Vapor Bubble Experiment

Science.gov (United States)

Gokhale, Shripad; Plawsky, Joel; Wayner, Peter C., Jr.; Zheng, Ling; Wang, Ying-Xi

2002-11-01

Microgravity experiments on the Constrained Vapor Bubble Heat Exchanger, CVB, are being developed for the International Space Station. In particular, we present results of a precursory experimental and theoretical study of the vertical Constrained Vapor Bubble in the Earth's environment. A novel non-isothermal experimental setup was designed and built to study the transport processes in an ethanol/quartz vertical CVB system. Temperature profiles were measured using an in situ PC (personal computer)-based LabView data acquisition system via thermocouples. Film thickness profiles were measured using interferometry. A theoretical model was developed to predict the curvature profile of the stable film in the evaporator. The concept of the total amount of evaporation, which can be obtained directly by integrating the experimental temperature profile, was introduced. Experimentally measured curvature profiles are in good agreement with modeling results. For microgravity conditions, an analytical expression, which reveals an inherent relation between temperature and curvature profiles, was derived.

Tank Vapor Characterization Project: Vapor space characterization of waste Tank A-101, Results from samples collected on June 8, 1995

International Nuclear Information System (INIS)

Pool, K.H.; Clauss, T.W.; McVeety, B.D.; Evans, J.C.; Thomas, B.L.; Olsen, K.B.; Fruchter, J.S.; Ligotke, M.W.

1995-11-01

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-A-101 (Tank A-101) at the Hanford Site in Washington State. The results described in this report were obtained to characterize the vapors present in the tank headspace and to support safety evaluations and tank-farm operations. The results include air concentrations of selected inorganic and organic analytes and grouped compounds from samples obtained by Westinghouse Hanford Company (WHC) and provided for analysis to Pacific Northwest National Laboratory (PNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNL. Analyte concentrations were based on analytical results and, where appropriate, sample volumes provided by WHC. A summary of the results is listed in Table 1. Detailed descriptions of the analytical results appear in the text

Analysis of the one-dimensional transient compressible vapor flow in heat pipes

Science.gov (United States)

Jang, Jong H.; Faghri, Amir; Chang, Won S.

1991-01-01

The transient compressible one-dimensional vapor flow dynamics in a heat pipe is modeled. The numerical results are obtained by using the implicit non-iterative Beam-Warming finite difference method. The model is tested for simulated heat pipe vapor flow and actual vapor flow in cylindrical heat pipes. A good comparison of the present transient results for the simulated heat pipe vapor flow with the previous results of a two-dimensional numerical model is achieved and the steady state results are in agreement with the existing experimental data. The transient behavior of the vapor flow under subsonic, sonic, and supersonic speeds as well as high mass flow rates are successfully predicted.

Fifteen years of seismic monitoring at the Las Tres Virgenes, BCS, geothermal field; Quince anos de monitoreo sismico en el campo geotermico de Las Tres Virgenes, BCS

Energy Technology Data Exchange (ETDEWEB)

Ortiz Prieto, Irais; Lorenzo Pulido, Cecilia [Comision Federal de Electricidad, Gerencia de Proyectos Geotermoelectricos, Morelia, Michoacan (Mexico)]. E-mail: cecilia.lorenzo@cfe.gob.mx

2009-07-15

Seismic monitoring at the Las Tres Virgenes, BCS, geothermal field started in 1992 with an analog station of vertical components detecting a large number of earthquakes of varying magnitudes. In February 1993, a seismic network was installed, composed of six digital stations DR-2000-with S-6000 and S-5000 sensors and three registration channels (N-S, E-W and vertical). This was the basis for the development of a program to correct arrival-time data for P and S waves due to instrument drift. From January to April 1994 and May to August 1995, based on the 170 seismic events recorded, a velocity model was proposed. From December 1995 to July 1996, seismic data were processed and interpreted, and zones of occurrence were determined for events according to magnitude and the predominant noise in the field. From September 2003 to December 2004, 10 seismic stations (permanent and temporary) were installed and monitored and it was concluded the most active fault system was El Volcan. From September to December 2004, production wells LV-4 and LV-13 were acid-stimulated and seismic monitoring during this period allowed for the definition of two important seismic zones, both related to the El Volcan fault system and to injection well LV-8. After reopening these production wells, it was concluded an increase in seismic activity had occurred. From May to August 2006, information was compiled from the seismic network and it was concluded El Partido had became the most active fault system. Presently the seismic network in this field is composed of one SARA station and four K2 units. The SARA station is telemetrically connected to the base station. [Spanish] En el campo geotermico de Las Tres Virgenes, BCS, el monitoreo sismico empezo a partir de 1992 con una sola estacion analogica de registro vertical, la cual detecto una gran cantidad de temblores de distintas magnitudes. En febrero de 1993 se instalo una red sismica con seis estaciones digitales DR-2000 con sensores S-6000 y S

Processing Maple Syrup with a Vapor Compression Distiller: An Economic Analysis

Science.gov (United States)

Lawrence D. Garrett

1977-01-01

A test of vapor compression distillers for processing maple syrup revealed that: (1) vapor compression equipment tested evaporated 1 pound of water with .047 pounds of steam equivalent (electrical energy); open-pan evaporators of similar capacity required 1.5 pounds of steam equivalent (oil energy) to produce 1 pound of water; (2) vapor compression evaporation produced...

Experimental study of the spill and vaporization of a volatile liquid

International Nuclear Information System (INIS)

Bohl, Douglas; Jackson, Gregory

2007-01-01

Pool and vapor cloud characteristics of an acetone spill issuing from the downstream wall of a flow obstruction oriented perpendicular to a uniform flow were investigated experimentally. Data indicate that the spill event was largely governed by the temperature of the surface in relation to the boiling point of the spilled liquid. The free stream velocity (ranging from 0.75 to 3.0 m/s) also impacted the spreading of the spill. Planar laser-induced fluorescence (PLIF) was used to measure acetone vapor concentrations during the transient pool spreading and vaporization in a window 60 cm long by 50 cm high and located downstream of the 16 cm high obstruction. The recirculation region induced by the flow obstruction caused upstream transport of the acetone vapor along the spill surface, after which it was convected vertically along the obstruction wall before being entrained into the flow and convected downstream. The recirculating flow caused regions of vapor within the flammability limits to be localized near the flow obstruction. These regions moved into and out of the measurement plane by large three-dimensional flow structures. The flammable region of the evolved vapor cloud was observed to grow well past the downstream edge of the measurement domain. With decreasing wind speeds, both the mass of acetone vapor within the flammability limits and the total spill event time increased significantly. The data presented herein provides a basis for validating future spill models of hazardous chemical releases, where complex turbulent flow modeling must be coupled with spill spreading and vaporization dynamics

Post-Decontamination Vapor Sampling and Analytical Test Methods

Science.gov (United States)

2015-08-12

is decontaminated that could pose an exposure hazard to unprotected personnel. The chemical contaminants may include chemical warfare agents (CWAs... decontamination process. Chemical contaminants can include chemical warfare agents (CWAs) or their simulants, nontraditional agents (NTAs), toxic industrial...a range of test articles from coupons, panels, and small fielded equipment items. 15. SUBJECT TERMS Vapor hazard; vapor sampling; chemical warfare

Method and apparatus for suppressing electron generation in a vapor source for isotope separation

International Nuclear Information System (INIS)

Janes, G.S.

1979-01-01

A system for applying accelerating forces to ionized particles of a vapor in a manner to suppress the flow of electron current from the vapor source. The accelerating forces are applied as an electric field in a configuration orthogonal to a magnetic field. The electric field is applied between one or more anodes in the plasma and one or more cathodes operated as electron emitting surfaces. The circuit for applying the electric field floats the cathodes with respect to the vapor source, thereby removing the vapor source from the circuit of electron flow through the plasma and suppressing the flow of electrons from the vapor source. The potential of other conducting structures contacting the plasma is controlled at or permitted to seek a level which further suppresses the flow of electron currents from the vapor source. Reducing the flow of electrons from the vapor source is particularly useful where the vapor is ionized with isotopic selectivity because it avoids superenergization of the vapor by the electron current

Mineralogía del proceso de biodesulfurización de carbones provenientes de la zona río Guachinte - río Asnazú (Valle del Cauca y Cauca)

OpenAIRE

Cardona Rendón, Isabel Cristina

2008-01-01

En Colombia, los depósitos carboníferos se encuentran distribuidos a lo largo de todo el país, encontrándose las mayores reservas en los departamentos de La Guajira, Cesar y Cundinamarca. Los carbones de la región suroccidental del país son útiles para la generación de vapor, pero tienen los más altos contenidos de azufre, principalmente en forma de azufre orgánico y pirita. Para dos muestras de carbón provenientes de la zona río Guachinte – río Asnazú, fue llevado a cabo un proceso de biodes...

In-well vapor stripping drilling and characterization work plan

International Nuclear Information System (INIS)

Koegler, K.J.

1994-01-01

This work plan provides the information necessary for drilling, sampling, and hydrologic testing of wells to be completed in support of a demonstration of the in-well vapor stripping system. The in-well vapor stripping system is a remediation technology designed to preferentially extract volatile organic compounds (VOCs) from contaminated groundwater by converting them to a vapor phase. Air-lift pumping is used to lift and aerate groundwater within the well. The volatiles escaping the aerated water are drawn off by a slight vacuum and treated at the surface while the water is allowed to infiltrate the vadose zone back to the watertable

A theoretical study of the growth of large sodium vapor bubbles in liquid sodium, including the effect of noncondensables and of vapor convection

International Nuclear Information System (INIS)

Casadei, F.; Donne, M.D.

1983-01-01

The study of the dynamics of the expansion of large bubbles of hot sodium vapor in a pool of liquid sodium plays an important role in understanding the effects of a hypothetical core disruptive accident. A model of the growth of the bubble in the pool is described. The equations of the motion of the liquid and of the nonsteady heat diffusion problem are solved together with the continuity and energy equations for the vapor phase. The first set of calculations has been performed with constant evaporation and condensation coefficients. In the second set, however, due account has been taken of the effect on condensation of noncondensable fission gases and vapor convection. Due to the very high calculated vapor velocities, noncondensable gases have little effect on the condensation rate, and the percentage amount of condensed sodium is considerably higher than previously calculated by other authors

On the vapor-liquid equilibrium in hydroprocessing reactors

Energy Technology Data Exchange (ETDEWEB)

Chen, J.; Munteanu, M.; Farooqi, H. [National Centre for Upgrading Technology, Devon, AB (Canada)

2009-07-01

When petroleum distillates undergo hydrotreating and hydrocracking, the feedstock and hydrogen pass through trickle-bed catalytic reactors at high temperatures and pressures with large hydrogen flow. As such, the oil is partially vaporized and the hydrogen is partially dissolved in liquid to form a vapor-liquid equilibrium (VLE) system with both vapor and liquid phases containing oil and hydrogen. This may result in considerable changes in flow rates, physical properties and chemical compositions of both phases. Flow dynamics, mass transfer, heat transfer and reaction kinetics may also be modified. Experimental observations of VLE behaviours in distillates with different feedstocks under a range of operating conditions were presented. In addition, VLE was predicted along with its effects on distillates in pilot and commercial scale plants. tabs., figs.

Eficiencia y disimetría: El caso bioético de la máquina de vapor y de la idea de Carnot

Directory of Open Access Journals (Sweden)

Ingeborg Carvajal Freese

2012-01-01

Full Text Available Sin lugar a dudas, la máquina de vapor representa un prototipo de aquellas iniciativas tecnológicas que parecían destinadas a cumplir el sueño de progreso, poder y control ilimitados. Sadi Carnot visualizó en la energía de vapor el motor universal e intuyó que de ahí en adelante el mundo irrevocablemente se fracturaría en dos: por un lado permanecerían, estáticos y atrasados, los pueblos primitivos productores de calor; por el otro, avanzarían de manera acelerada los hombres civilizados poseedores de la nueva máquina generadora de trabajo. Aún hoy, cuando el mito tecnológico del progreso ilimitado se ha roto, las brechas sociales siguen indefectiblemente vinculadas a los inventos que se traducen en una redistribución de la energía. Corresponde a la Bioética hacer visibles los ámbitos que se afectan cuando la eficiencia técnica se transmuta en valor y las disimetrías concomitantes se difunden y se amplifican por doquier.

An empirical equation for the enthalpy of vaporization of quantum liquids

International Nuclear Information System (INIS)

Kuz, Victor A.; Meyra, Ariel G.; Zarragoicoechea, Guillermo J.

2004-01-01

An empirical equation for the enthalpy of vaporization of quantum fluids is presented. Dimensionless analysis is used to define enthalpy of vaporization as a function of temperature with a standard deviation of about 1%. Experimental data represented in these variables show two different behaviours and exhibit different maximum values of the enthalpy of vaporization, one corresponding to fluids with a triple point and the other to fluids having a lambda point. None of the existing empirical equations are able to describe this fact. Also enthalpy of vaporization of helium-3, n-deuterium and n-tritium are estimated

Chemical vapor deposited fiber coatings and chemical vapor infiltrated ceramic matrix composites

Energy Technology Data Exchange (ETDEWEB)

Kmetz, M.A.

1992-01-01

Conventional Chemical Vapor Deposition (CVD) and Organometallic Chemical Vapor Deposition (MOCVD) were employed to deposit a series of interfacial coatings on SiC and carbon yarn. Molybdenum, tungsten and chromium hexacarbonyls were utilized as precursors in a low temperature (350[degrees]C) MOCVD process to coat SiC yarn with Mo, W and Cr oxycarbides. Annealing studies performed on the MoOC and WOC coated SiC yarns in N[sub 2] to 1,000[degrees]C establish that further decomposition of the oxycarbides occurred, culminating in the formation of the metals. These metals were then found to react with Si to form Mo and W disilicide coatings. In the Cr system, heating in N[sub 2] above 800[degrees]C resulted in the formation of a mixture of carbides and oxides. Convention CVD was also employed to coat SiC and carbon yarn with C, Bn and a new interface designated BC (a carbon-boron alloy). The coated tows were then infiltrated with SiC, TiO[sub 2], SiO[sub 2] and B[sub 4]C by a chemical vapor infiltration process. The B-C coatings were found to provide advantageous interfacial properties over carbon and BN coatings in several different composite systems. The effectiveness of these different coatings to act as a chemically inert barrier layer and their relationship to the degree of interfacial debonding on the mechanical properties of the composites were examined. The effects of thermal stability and strength of the coated fibers and composites were also determined for several difference atmospheres. In addition, a new method for determining the tensile strength of the as-received and coated yarns was also developed. The coated fibers and composites were further characterized by AES, SEM, XPS, IR and X-ray diffraction analysis.

Vaporization of a mixed precursors in chemical vapor deposition for YBCO films

Science.gov (United States)

Zhou, Gang; Meng, Guangyao; Schneider, Roger L.; Sarma, Bimal K.; Levy, Moises

1995-01-01

Single phase YBa2Cu3O7-delta thin films with T(c) values around 90 K are readily obtained by using a single source chemical vapor deposition technique with a normal precursor mass transport. The quality of the films is controlled by adjusting the carrier gas flow rate and the precursor feed rate.

The self-similar turbulent flow of low-pressure water vapor

Science.gov (United States)

Konyukhov, V. K.; Stepanov, E. V.; Borisov, S. K.

2018-05-01

We studied turbulent flows of water vapor in a pipe connecting two closed vessels of equal volume. The vessel that served as a source of water vapor was filled with adsorbent in the form of corundum ceramic balls. These ceramic balls were used to obtain specific conditions to lower the vapor pressure in the source vessel that had been observed earlier. A second vessel, which served as a receiver, was empty of either air or vapor before each vapor sampling. The rate of the pressure increase in the receiver vessel was measured in a series of six samplings performed with high precision. The pressure reduction rate in the source vessel was found to be three times lower than the pressure growth rate in the receiver vessel. We found that the pressure growth rates in all of the adjacent pairs of samples could be arranged in a combination that appeared to be identical for all pairs, and this revealed the existence of a rather interesting and peculiar self-similarity law for the sampling processes under consideration.

La superaci??n del modelo del ??ngel del hogar:

OpenAIRE

Hurtado Mu??oz, M??nica

2012-01-01

La Tesis Doctoral titulada "La superaci??n del modelo del "??ngel del hogar". Recuperaci??n de la escritora Leonor Canalejas y Fustegueras (1869-1945)" aborda, en primer lugar, un an??lisis sociol??gico de las circunstancias que rodearon a la mujer espa??ola en el cambio de siglo en el ??mbito social y educativo, en un intento de esclarecer las caracter??sticas propias del contexto en el que la mujer accede a la intelectualidad en general y a la literatura en particular. Esta parte concluye q...

Water vapor differential absorption lidar development and evaluation

Science.gov (United States)

Browell, E. V.; Wilkerson, T. D.; Mcllrath, T. J.

1979-01-01

A ground-based differential absorption lidar (DIAL) system is described which has been developed for vertical range-resolved measurements of water vapor. The laser transmitter consists of a ruby-pumped dye laser, which is operated on a water vapor absorption line at 724.372 nm. Part of the ruby laser output is transmitted simultaneously with the dye laser output to determine atmospheric scattering and attenuation characteristics. The dye and ruby laser backscattered light is collected by a 0.5-m diam telescope, optically separated in the receiver package, and independently detected using photomultiplier tubes. Measurements of vertical water vapor concentration profiles using the DIAL system at night are discussed, and comparisons are made between the water vapor DIAL measurements and data obtained from locally launched rawinsondes. Agreement between these measurements was found to be within the uncertainty of the rawinsonde data to an altitude of 3 km. Theoretical simulations of this measurement were found to give reasonably accurate predictions of the random error of the DIAL measurements. Confidence in these calculations will permit the design of aircraft and Shuttle DIAL systems and experiments using simulation results as the basis for defining lidar system performance requirements

Thermodynamic and transport properties of sodium liquid and vapor

International Nuclear Information System (INIS)

Fink, J.K.; Leibowitz, L.

1995-01-01

Data have been reviewed to obtain thermodynamically consistent equations for thermodynamic and transport properties of saturated sodium liquid and vapor. Recently published Russian recommendations and results of equation of state calculations on thermophysical properties of sodium have been included in this critical assessment. Thermodynamic properties of sodium liquid and vapor that have been assessed include: enthalpy, heat capacity at constant pressure, heat capacity at constant volume, vapor pressure, boiling point, enthalpy of vaporization, density, thermal expansion, adiabatic and isothermal compressibility, speed of sound, critical parameters, and surface tension. Transport properties of liquid sodium that have been assessed include: viscosity and thermal conductivity. For each property, recommended values and their uncertainties are graphed and tabulated as functions of temperature. Detailed discussions of the analyses and determinations of the recommended equations include comparisons with recommendations given in other assessments and explanations of consistency requirements. The rationale and methods used in determining the uncertainties in the recommended values are also discussed

Tank Vapor Characterization Project. Headspace vapor characterization of Hanford Waste Tank AX-102: Results from samples collected on June 27, 1995

International Nuclear Information System (INIS)

Clauss, T.W.; Pool, K.H.; Evans, J.C.; McVeety, B.D.; Thomas, B.L.; Olsen, K.B.; Fruchter, J.S.; Ligotke, M.W.

1995-11-01

This report describes the analytical results of vapor samples taken from the headspace of the waste storage tank 241-AX-102 (Tank AX-102) at the Hanford Site in Washington State. The results described in this report were obtained to characterize the vapors present in the tank headspace and to support safety evaluations and tank-farm operations. The results include air concentrations of selected inorganic and organic analytes and grouped compounds from samples obtained by Westinghouse Hanford Company (WHC) and provided for analysis to Pacific Northwest Laboratory (PNL). Analyses were performed by the Vapor Analytical Laboratory (VAL) at PNL. Analyte concentrations were based on analytical results and, where appropriate, sample volumes provided by WHC. Detailed descriptions of the analytical results appear in the text

DuPont Chemical Vapor Technical Report

International Nuclear Information System (INIS)

MOORE, T.L.

2003-01-01

DuPont Safety Resources was tasked with reviewing the current chemical vapor control practices and providing preventive recommendations on best commercial techniques to control worker exposures. The increased focus of the tank closure project to meet the 2024 Tri-Party Agreement (TPA) milestones has surfaced concerns among some CH2MHill employees and other interested parties. CH2MHill is committed to providing a safe working environment for employees and desires to safely manage the tank farm operations using appropriate control measures. To address worker concerns, CH2MHill has chartered a ''Chemical Vapors Project'' to integrate the activities of multiple CH2MHill project teams, and solicit the expertise of external resources, including an independent Industrial Hygiene expert panel, a communications consultant, and DuPont Safety Resources. Over a three-month time period, DuPont worked with CH2MHill ESH and Q, Industrial Hygiene, Engineering, and the independent expert panel to perform the assessment. The process included overview presentations, formal interviews, informal discussions, documentation review, and literature review. DuPont Safety Resources concluded that it is highly unlikely that workers in the tank farms are exposed to chemicals above established standards. Additionally, the conventional and radiological chemistry is understood, the inherent chemical hazards are known, and the risk associated with chemical vapor exposure is properly managed. The assessment highlighted management's commitment to addressing chemical vapor hazards and controlling the associated risks. Additionally, we found the Industrial Hygiene staff to be technically competent and well motivated. The tank characterization data resides in a comprehensive database containing the tank chemical compositions and relevant airborne concentrations

Evaporation monitoring and composition control of alloy systems with widely differing vapor pressures

International Nuclear Information System (INIS)

Anklam, T.M.; Berzins, L.V.; Braun, D.G.; Haynam, C.; McClelland, M.A.; Meier, T.

1994-10-01

Lawrence Livermore National Laboratory is developing sensors and controls to improve and extend electron beam materials processing technology to alloy systems with constituents of widely varying vapor pressure. The approach under development involves using tunable lasers to measure the density and composition of the vapor plume. A laser based vaporizer control system for vaporization of a uranium-iron alloy has been previously demonstrated in multi-hundred hour, high rate vaporization experiments at LLNL. This paper reviews the design and performance of the uranium vaporization sensor and control system and discusses the extension of the technology to monitoring of uranium vaporization. Data is presented from an experiment in which titanium wire was fed into a molten niobium pool. Laser data is compared to deposited film composition and film cross sections. Finally, the potential for using this technique for composition control in melting applications is discussed

Experimental study of vapor explosion of molten salt and low boiling point liquid

International Nuclear Information System (INIS)

Iida, Yoshihiro; Takashima, Takeo

1987-01-01

Fundamental study of vapor explosion using small drops of high temperature liquid and low boiling point liquid and a series of small-scale vapor explosion tests are carried out. A single or plural drops of molten LiNO 3 are dropped into ethyl alcohol and the temperature range of two liquids wherein the fragmentation occurs is examined. The propagation phenomenon of vapor explosion between two drops is photographed and the pressure trace is proved to be well consistent with the behavior of the vapor bubble regions. A small amount of molten Flinak and tin which are enclosed in a test tube is dropped into tapped water. The temperature effect of two liquids onto the occurrence of vapor explosion is investigated. Some considerations are made with respect to the upper and lower temperature limits of vapor explosion to occur. A qualitative modeling of vapor explosion mechanism is proposed and discussed. (author)

EVALUACIÓN DE LA RETROGRADACIÓN DEL ALMIDÓN EN HARINA DE YUCA PRECOCIDA

OpenAIRE

Rodríguez-Sandoval, Eduardo; Sandoval-Aldana, Angélica; Fernández-Quintero, Alejandro

2007-01-01

Las modificaciones del almidón, que ocurren durante el proceso de elaboración de harina de yuca precocida, se evaluaron utilizando técnicas como calorimetría diferencial de barrido (CDB), difracción de rayos X, comportamiento al empastamiento y capacidad de formación de complejo con yodo. La harina precocida se obtuvo a partir de trozos de parénquima de yuca cocinados en vapor o en agua a ebullición, los cuales fueron posteriormente almacenados a 5 ºC o a -20 ºC por 24 h. La temperatura utili...

Marketing practices of vapor store owners.

Science.gov (United States)

Cheney, Marshall; Gowin, Mary; Wann, Taylor Franklin

2015-06-01

We examined the marketing strategies for local vapor stores in a large metropolitan area in Oklahoma. Vapor store owners or managers (n = 33) participated in individual interviews regarding marketing practices in 2014. We asked owners about their marketing strategies and the groups they targeted. We transcribed the interviews and analyzed them for themes. Store owners used a variety of marketing strategies to bring new customers to their stores and keep current customers coming back. These marketing strategies showed many parallels to tobacco industry strategies. Most owners engaged in some form of traditional marketing practices (e.g., print media), but only a few used radio or television advertising because of budget constraints. Owners used social media and other forms of electronic communication, pricing discounts and specials, and loyalty programs. Owners also had booths at local events, sponsored community events, and hosted them in their stores. Owners attempted to target different groups of users, such as college students and long-term smokers. Local vapor store marketing practices closely resemble current and former tobacco industry marketing strategies. Surveillance of marketing practices should include local and Web-based strategies.

Marketing Practices of Vapor Store Owners

Science.gov (United States)

Gowin, Mary; Wann, Taylor Franklin

2015-01-01

Objectives. We examined the marketing strategies for local vapor stores in a large metropolitan area in Oklahoma. Methods. Vapor store owners or managers (n = 33) participated in individual interviews regarding marketing practices in 2014. We asked owners about their marketing strategies and the groups they targeted. We transcribed the interviews and analyzed them for themes. Results. Store owners used a variety of marketing strategies to bring new customers to their stores and keep current customers coming back. These marketing strategies showed many parallels to tobacco industry strategies. Most owners engaged in some form of traditional marketing practices (e.g., print media), but only a few used radio or television advertising because of budget constraints. Owners used social media and other forms of electronic communication, pricing discounts and specials, and loyalty programs. Owners also had booths at local events, sponsored community events, and hosted them in their stores. Owners attempted to target different groups of users, such as college students and long-term smokers. Conclusions. Local vapor store marketing practices closely resemble current and former tobacco industry marketing strategies. Surveillance of marketing practices should include local and Web-based strategies. PMID:25880960

Nuclear vapor thermal reactor propulsion technology

International Nuclear Information System (INIS)

Maya, I.; Diaz, N.J.; Dugan, E.T.; Watanabe, Y.; McClanahan, J.A.; Wen-Hsiung Tu; Carman, R.L.

1993-01-01

The conceptual design of a nuclear rocket based on the vapor core reactor is presented. The Nuclear Vapor Thermal Rocket (NVTR) offers the potential for a specific impulse of 1000 to 1200 s at thrust-to-weight ratios of 1 to 2. The design is based on NERVA geometry and systems with the solid fuel replaced by uranium tetrafluoride (UF 4 ) vapor. The closed-loop core does not rely on hydrodynamic confinement of the fuel. The hydrogen propellant is separated from the UF 4 fuel gas by graphite structure. The hydrogen is maintained at high pressure (∼100 atm), and exits the core at 3,100 K to 3,500 K. Zirconium carbide and hafnium carbide coatings are used to protect the hot graphite from the hydrogen. The core is surrounded by beryllium oxide reflector. The nuclear reactor core has been integrated into a 75 klb engine design using an expander cycle and dual turbopumps. The NVTR offers the potential for an incremental technology development pathway to high performance gas core reactors. Since the fuel is readily available, it also offers advantages in the initial cost of development, as it will not require major expenditures for fuel development

An opacity-sampled treatment of water vapor

Science.gov (United States)

Alexander, David R.; Augason, Gordon C.; Johnson, Hollis R.

1989-01-01

Although the bands of H2O are strong in the spectra of cool stars and calculations have repeatedly demonstrated their significance as opacity sources, only approximate opacities are currently available, due both to the difficulty of accounting for the millions of lines involved and to the inadequacy of laboratory and theoretical data. To overcome these obstacles, a new treatment is presented, based upon a statistical representation of the water vapor spectrum derived from available laboratory data. This statistical spectrum of water vapor employs an exponential distribution of line strengths and random positions of lines whose overall properties are forced to reproduce the mean opacities observed in the laboratory. The resultant data set is then treated by the opacity-sampling method exactly as are all other lines, both molecular and atomic. Significant differences are found between the results of this improved treatment and the results obtained with previous treatments of water-vapor opacity.