WorldWideScience

Sample records for degree sweptback wing

  1. Experimental static aerodynamic forces and moments at high subsonic speeds on a missile model during simulated launching from the midsemispan location of a 45 degree sweptback wing-fuselage-pylon combination

    Science.gov (United States)

    Alford, William J; King, Thomas, Jr

    1957-01-01

    An investigation was made at high subsonic speeds in the Langley high-speed 7- by 10-foot tunnel to determine the static aerodynamic forces and moments on a missile model during simulated launching from the midsemispan location of a 45 degree sweptback wing-fuselage-pylon combination. The results indicated significant variations in all the aerodynamic components with changes in chordwise location of the missile. Increasing the angle of attack caused increases in the induced effects on the missile model because of the wing-fuselage-pylon combination. Increasing the Mach number had little effect on the variations of the missile aerodynamic characteristics with angle of attack except that nonlinearities were incurred at smaller angles of attack for the higher Mach numbers. The effects of finite wing thickness on the missile characteristics, at zero angle of attack, increase with increasing Mach number. The effects of the pylon on the missile characteristics were to causeincreases in the rolling-moment variation with angle of attack and a negative displacement of the pitching-moment curves at zero angle of attack. The effects of skewing the missile in the lateral direction relative to and sideslipping the missile with the wing-fuselage-pylon combination were to cause additional increments in side force at zero angle of attack. For the missile yawing moments the effects of changes in skew or sideslip angles were qualitatively as would be expected from consideration of the isolated missile characteristics, although there existed differences in theyawing-moment magnitudes.

  2. On the Installation of Jet Engine Nacelles on a Wing Fourth Partial Report: Pressure-Distribution Measurements on a Sweptback Wing with Jet Engine Nacelle

    Science.gov (United States)

    Buschner, R.

    1949-01-01

    The present report, which deals with pressure-distribution measurements made on a sweptback wing with a jet engine nacelle, is similar to a report on pressure-distribution measurements on a rectangular wing with a jet engine nacelle (second partial report). Here, in investigations preliminary to high-speed measurements, as in the second partial report, useful arrangements and fillet designs have been discovered.

  3. Interaction of a finite-span synthetic jet near the tip of a sweptback wing

    Science.gov (United States)

    Vasile, Joseph D.; Amitay, Michael

    2015-06-01

    An experimental investigation was performed to study the three-dimensional flow interaction of a finite-span (aspect ratio of 18) synthetic jet located near the tip of a sweptback wing (cross-sectional profile of NACA 4421, aspect ratio of 4, and sweep angle of 30°) at a Reynolds number of 105 and at three angles of attack of 0°, 9°, and 15.5° (covering the range of attached to separated flow in the vicinity of the synthetic jet). Three blowing ratios were considered as 0.8, 1.2, and 2. Stereoscopic particle image velocimetry data were collected at multiple 2-D planes in the vicinity of the jet's orifice, which were then used to reconstruct the flow volume, and the effect of the jet's blowing ratio was analyzed using time-averaged and phase-averaged statistics. The study showed that the flow field in the vicinity of the synthetic jet orifice becomes highly three-dimensional and is governed by the streamwise structures that are associated with the finite span of the orifice (edge vortices). Furthermore, it was demonstrated that the baseline flow field that develops over a swept-back configuration (characterized by spanwise and streamwise vorticity components) is responsible for the immediate breakdown of the coherent structures that are introduced by the synthetic jet orifice and for the formation of the secondary flow structures that were seen in the time-averaged flow field. Moreover, the presence of a tip vortex results in the development of a non-uniform (in the spanwise direction) spanwise boundary layer that becomes more pronounced with increasing angle of attack. Consequently, the development of the flow structures is altered. Finally, the present work suggests that the location of the synthetic jet along the span is not as important (as the angle of attack and the blowing ratio) in the overall formation and evolution of the flow structures issued from the jet. However, the size and strength of these structures are affected by the jet's spanwise location.

  4. Normal-Force and Hinge-Moment Characteristics at Transonic Speeds of Flap-Type Ailerons at Three Spanwise Locations on a 4-Percent-Thick Sweptback-Wing-Body Model and Pressure-Distribution Measurements on an Inboard Aileron

    Science.gov (United States)

    Runckel, Jack F.; Hieser, Gerald

    1961-01-01

    An investigation has been conducted at the Langley 16-foot transonic tunnel to determine the loading characteristics of flap-type ailerons located at inboard, midspan, and outboard positions on a 45 deg. sweptback-wing-body combination. Aileron normal-force and hinge-moment data have been obtained at Mach numbers from 0.80 t o 1.03, at angles of attack up to about 27 deg., and at aileron deflections between approximately -15 deg. and 15 deg. Results of the investigation indicate that the loading over the ailerons was established by the wing-flow characteristics, and the loading shapes were irregular in the transonic speed range. The spanwise location of the aileron had little effect on the values of the slope of the curves of hinge-moment coefficient against aileron deflection, but the inboard aileron had the greatest value of the slope of the curves of hinge-moment coefficient against angle of attack and the outboard aileron had the least. Hinge-moment and aileron normal-force data taken with strain-gage instrumentation are compared with data obtained with pressure measurements.

  5. Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

    Science.gov (United States)

    Bird, John D; Lichtenstein, Jacob H; Jaquet, Byron M

    1952-01-01

    Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

  6. The lateral-directional characteristics of a 74-degree Delta wing employing gothic planform vortex flaps

    Science.gov (United States)

    Grantz, A. C.

    1984-01-01

    The low speed lateral/directional characteristics of a generic 74 degree delta wing body configuration employing the latest generation, gothic planform vortex flaps was determined. Longitudinal effects are also presented. The data are compared with theoretical estimates from VORSTAB, an extension of the Quasi vortex lattice Method of Lan which empirically accounts for vortex breakdown effects in the calculation of longitudinal and lateral/directional aerodynamic characteristics. It is indicated that leading edge deflections of 30 and 40 degrees reduce the magnitude of the wing effective dihedral relative to the baseline for a specified angle of attack or lift coefficient. For angles of attack greater than 15 degrees, these flap deflections reduce the configuration directional stability despite improved vertical tail effectiveness. It is shown that asymmetric leading edge deflections are inferior to conventional ailerons in generating rolling moments. VORSTAB calculations provide coarse lateral/directional estimates at low to moderate angles of attack. The theory does not account for vortex flow induced, vertical tail effects.

  7. Degree of Vascular Encasement in Sphenoid Wing Meningiomas Predicts Postoperative Ischemic Complications.

    Science.gov (United States)

    McCracken, D Jay; Higginbotham, Raymond A; Boulter, Jason H; Liu, Yuan; Wells, John A; Halani, Sameer H; Saindane, Amit M; Oyesiku, Nelson M; Barrow, Daniel L; Olson, Jeffrey J

    2017-06-01

    Sphenoid wing meningiomas (SWMs) can encase arteries of the circle of Willis, increasing their susceptibility to intraoperative vascular injury and severe ischemic complications. To demonstrate the effect of circumferential vascular encasement in SWM on postoperative ischemia. A retrospective review of 75 patients surgically treated for SWM from 2009 to 2015 was undertaken to determine the degree of circumferential vascular encasement (0°-360°) as assessed by preoperative magnetic resonance imaging (MRI). A novel grading system describing "maximum" and "total" arterial encasement scores was created. Postoperative MRIs were reviewed for total ischemia volume measured on sequential diffusion-weighted images. Of the 75 patients, 89.3% had some degree of vascular involvement with a median maximum encasement score of 3.0 (2.0-3.0) in the internal carotid artery (ICA), M1, M2, and A1 segments; 76% of patients had some degree of ischemia with median infarct volume of 3.75 cm 3 (0.81-9.3 cm 3 ). Univariate analysis determined risk factors associated with larger infarction volume, which were encasement of the supraclinoid ICA ( P 62 cm 3 was found when the ICA, M1, and A1 vessels all had ≥360° involvement ( P = .001). Residual tumor was associated with smaller infarct volumes ( P = .022). As infarction volume increased, so did modified Rankin Score at discharge ( P = .025). Subtotal resection should be considered in SWM with significant vascular encasement of proximal arteries to limit postoperative ischemic complications.

  8. Application of slender wing benefits to military aircraft

    Science.gov (United States)

    Polhamus, E. C.

    1983-01-01

    A review is provided of aerodynamic research conducted at the Langley Research Center with respect to the application of slender wing benefits in the design of high-speed military aircraft, taking into account the supersonic performance and leading-edge vortex flow associated with very highly sweptback wings. The beginning of the development of modern classical swept wing jet aircraft is related to the German Me 262 project during World War II. In the U.S., a theoretical study conducted by Jones (1945) pointed out the advantages of the sweptback wing concept. Developments with respect to variable sweep wings are discussed, taking into account early research in 1946, a joint program of the U.S. with the United Kingdom, the tactical aircraft concept, and the important part which the Langley variable-sweep research program played in the development of the F-111, F-14, and B-1. Attention is also given to hybrid wings, vortex flow theory development, and examples of flow design technology.

  9. Effect of Fuselage and Tail Surfaces on Low-speed Yawing Characteristics of a Swept-wing Model as Determined in Curved-flow Test Section of Langley Stability Tunnel

    Science.gov (United States)

    Bird, John D; Jaquet, Byron M; Cowan, John W

    1951-01-01

    Results are presented of a wind-tunnel investigation made to determine the influence of the fuselage and tail surfaces on the rotary derivatives in yawing flight of a transonic-airplane configuration having 45 degrees sweptback wing and tail surfaces. The tests were run in the curved-flow test section of the Langley stability tunnel at a Reynolds number of 1.07 X 10 to the sixth power and consisted of balance measurements throughout the angle-of-attack range for several flight-path radii of curvature. The results are compared with data from forced-oscillation and free-oscillation tests, and a description of testing techniques used is included.

  10. Vortices around Dragonfly Wings

    OpenAIRE

    Kweon, Jihoon; Choi, Haecheon

    2009-01-01

    Dragonfly beats its wings independently, resulting in its superior maneuverability. Depending on the magnitude of phase difference between the fore- and hind-wings of dragonfly, the vortical structures and their interaction with wings become significantly changed, and so does the aerodynamic performance. In this study, we consider hovering flights of modelled dragonfly with three different phase differences (phi=-90, 90, 180 degrees). The three-dimensional wing shape is based on that of Aesch...

  11. Effects of a sweptback hydrofoil on the force and longitudinal stability characteristics of a typical high-speed airplane

    Science.gov (United States)

    Wood, Raymond B

    1948-01-01

    An investigation was conducted in the Langley 8-foot high-speed tunnel to determine the effects of a sweptback hydrofoil on the force and longitudinal stability characteristics of a typical high-speed airplane. The Mach number range for this investigation was from 0.60 to 0.95 and at M = 1.20. The effects of the hydrofoil on the lift, drag, and pitching-moment characteristics are presented.

  12. Avian Wings

    Science.gov (United States)

    Liu, Tianshu; Kuykendoll, K.; Rhew, R.; Jones, S.

    2004-01-01

    This paper describes the avian wing geometry (Seagull, Merganser, Teal and Owl) extracted from non-contact surface measurements using a three-dimensional laser scanner. The geometric quantities, including the camber line and thickness distribution of airfoil, wing planform, chord distribution, and twist distribution, are given in convenient analytical expressions. Thus, the avian wing surfaces can be generated and the wing kinematics can be simulated. The aerodynamic characteristics of avian airfoils in steady inviscid flows are briefly discussed. The avian wing kinematics is recovered from videos of three level-flying birds (Crane, Seagull and Goose) based on a two-jointed arm model. A flapping seagull wing in the 3D physical space is re-constructed from the extracted wing geometry and kinematics.

  13. A method for calculating the lift and center of pressure of wing-body-tail combinations at subsonic, transonic, and supersonic speeds

    Science.gov (United States)

    Nielsen, Jack N; Kaattari, George E; Anastasio, Robert F

    1953-01-01

    A method is presented for calculating the lift and pitching-moment characteristics of circular cylindrical bodies in combination with triangular, rectangular, or trapezoidal wings or tails through the subsonic, transonic, and supersonic speed ranges. The method covers unbanked wings, sweptback leading edges or sweptforward trailing edges, low angles of attack, and the effects of wing and tail incidence. The wing-body interference is handled by the method presented in NACA RM's A51J04 and A52B06, and the wing-tail interference is treated by assuming one completely rolled-up vortex per wing panel and evaluating the tail load by strip theory. A computing table and set of design charts are presented which reduce the calculations to routine operations. Comparison is made between the estimated and experimental characteristics for a large number of wing-body and wing-body-tail combinations. Generally speaking, the lifts were estimated to within plus-or-minus 10 percent and the centers of pressure were estimated to within plus-or-minus 0.02 of the body length. The effect of wing deflection on wing-tail interference at supersonic speeds was not correctly predicted for triangular wings with supersonic leading edges.

  14. Wing flutter boundary prediction using unsteady Euler aerodynamic method

    Science.gov (United States)

    Lee-Rausch, Elizabeth M.; Batina, John T.

    1993-01-01

    Modifications to an existing 3D implicit upwind Euler/Navier-Stokes code for the aeroelastic analysis of wings are described. These modifications include the incorporation of a deforming mesh algorithm and the addition of the structural equations of motion for their simultaneous time-integration with the governing flow equations. The paper gives a brief description of these modifications and presents unsteady calculations which check the modifications to the code. Euler flutter results for an isolated 45 deg swept-back wing are compared with experimental data for seven freestream Mach numbers which define the flutter boundary over a range of Mach number from 0.499 to 1.14. These comparisons show good agreement in flutter characteristics for freestream Mach numbers below unity. For freestream Mach numbers above unity, the computed aeroelastic results predict a premature rise in the flutter boundary as compared with the experimental boundary. Steady and unsteady contours of surface Mach number and pressure are included to illustrate the basic flow characteristics of the time-marching flutter calculations and to aid in identifying possible causes for the premature rise in the computational flutter boundary.

  15. Angel's Wings

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    @@ Angel's wings had fallen off. It started slowly,a couple of feathers breaking loose in the wind,floating away in carefree spirals, then in clumps in the shower, matted wet and clogging the drain,until one day he woke in a thick layer of white plumage, quills snagging on the stained sheets.

  16. High performance forward swept wing aircraft

    Science.gov (United States)

    Koenig, David G. (Inventor); Aoyagi, Kiyoshi (Inventor); Dudley, Michael R. (Inventor); Schmidt, Susan B. (Inventor)

    1988-01-01

    A high performance aircraft capable of subsonic, transonic and supersonic speeds employs a forward swept wing planform and at least one first and second solution ejector located on the inboard section of the wing. A high degree of flow control on the inboard sections of the wing is achieved along with improved maneuverability and control of pitch, roll and yaw. Lift loss is delayed to higher angles of attack than in conventional aircraft. In one embodiment the ejectors may be advantageously positioned spanwise on the wing while the ductwork is kept to a minimum.

  17. Effect of leading edge roundness on a delta wing in wing-rock motion

    Science.gov (United States)

    Ng, T. Terry; Malcolm, Gerald N.

    1990-01-01

    The effect of wing leading-edge roundness on wing rock was investigated using flow visualization in a water tunnel. Eighty degree delta wing models were tested on free-to-roll and forced oscillation rigs. The onset of wing rock was delayed by increasing the roundness of the leading edges. The wing rock amplitude and frequency results suggested that damping was increased at lower angles of attack but reduced at higher angles of attack. Vortex lift-off and vortex breakdown, especially during dynamic situations, were strongly affected by the leading edge roundness. Different forms of wing rock motion could be sustained by combinations of vortex breakdown and vortex lift-off. Behaviors of the wing and vortex motions were explained by the influence of leading edge roundness on the separation location, vortex trajectory, and vortex breakdown.

  18. Resilin in dragonfly and damselfly wings and its implications for wing flexibility.

    Science.gov (United States)

    Donoughe, Seth; Crall, James D; Merz, Rachel A; Combes, Stacey A

    2011-12-01

    Although there is mounting evidence that passive mechanical dynamics of insect wings play an integral role in insect flight, our understanding of the structural details underlying insect wing flexibility remains incomplete. Here, we use comparative morphological and mechanical techniques to illuminate the function and diversity of two mechanisms within Odonata wings presumed to affect dynamic wing deformations: flexible resilin vein-joints and cuticular spikes. Mechanical tests show that joints with more resilin have lower rotational stiffness and deform more in response to a load applied to an intact wing. Morphological studies of 12 species of Odonata reveal that resilin joints and cuticular spikes are widespread taxonomically, yet both traits display a striking degree of morphological and functional diversity that follows taxonomically distinct patterns. Interestingly, damselfly wings (suborder Zygoptera) are mainly characterized by vein-joints that are double-sided (containing resilin both dorsally and ventrally), whereas dragonfly wings (suborder Epiprocta) are largely characterized by single-sided vein-joints (containing resilin either ventrally or dorsally, but not both). The functional significance and diversity of resilin joints and cuticular spikes could yield insight into the evolutionary relationship between form and function of wings, as well as revealing basic principles of insect wing mechanical design.

  19. Interval Finite Element Analysis of Wing Flutter

    Institute of Scientific and Technical Information of China (English)

    Wang Xiaojun; Qiu Zhiping

    2008-01-01

    The influences of uncertainties in structural parameters on the flutter speed of wing are studied. On the basis of the deterministic flutter analysis model of wing, the uncertainties in structural parameters are considered and described by interval numbers. By virtue of first-order Taylor series expansion, the lower and upper bound curves of the transient decay rate coefficient versus wind velocity are given. So the interval estimation of the flutter critical wind speed of wing can be obtained, which is more reasonable than the point esti- mation obtained by the deterministic flutter analysis and provides the basis for the further non-probabilistic interval reliability analysis of wing flutter. The flow chart for interval finite element model of flutter analysis of wing is given. The proposed interval finite element model and the stochastic finite element model for wing flutter analysis are compared by the examples of a three degrees of freedorn airfoil and fuselage and a 15° swepthack wing, and the results have shown the effectiveness and feasibility of the presented model. The prominent advantage of the proposed interval finite element model is that only the bounds of uncertain parameters axe required, and the probabilistic distribution densities or other statistical characteristics are not needed.

  20. DESIGN AND RESEARCH FOR A NEW TYPE BUOYANCY-LIFTING ROW FLYING-WINGS%一种新型浮升一体化排式飞翼的设计与研究

    Institute of Scientific and Technical Information of China (English)

    李峰; 叶正寅

    2009-01-01

    It has important sciencfic and engineering applications for aircrafts of low speed to design the buoyancy-lifting aircraft with both bigger volume and higher aerodynamic efficiency. Based on the nero-foil NACA0030, some aerodynamic configurations of row flying-wings with the higher volume efficiency (vol-me/surface) were constructed. Different arrayed row flying-wings were calculated and investigated minutely. An aerodynamic configuration of row sweptback flying-wings with the better maneuverability and stability was educed. The numerical simulation results indicate that the lift-drag ratios of row straight flying-wings and row sweptback flying-wings increase by up to 40% and 20%, respectively, and the aerodynamic efficiency of aircrafts are improved obviously from the block of airflow under the anterior flying-wing by the posterior flying-wing. Meanwhile, the chordwise size of buoyancy-lifting row flying-wings is comparatively small so that the surface tension of skin material can be reduced availably. This characteristic provides the wider scope on the skin flexible material selection for high altitude aircrafts.%设计既有较大的内部容积、又有高气动效率的新型浮升一体化气动布局对此类低速飞行器的发展具有重要的科学研究价值和工程应用前景.以NAcA0030翼型为基础,构造了具有较高体积率(体积/表面积)的排式飞翼气动布局.对不同排列形式的排式飞翼进行了详细的计算和评估分析,并提出了具有更好操纵性和稳定性的排式后掠飞翼气动布局.数值模拟结果表明:通过排式飞翼中后翼对前翼下方气流的阻滞作用,排式直飞翼和排式后掠飞翼的升阻比分别增大40%和20%,整个飞行器的气动效率显著提高;同时,浮升一体化排式飞翼的弦向尺寸较小,可有效降低材料的表面张力,这为高空飞行器表面柔性材料提供了较宽的选择范围.

  1. Induce Drag Reduction of an Airplane Wing

    Directory of Open Access Journals (Sweden)

    Md. Fazle Rabbi

    2015-06-01

    Full Text Available This work describes the aerodynamic characteristics for aircraft wing model with and without slotted winglet. When an aircraft moves forward with a high speed then a small circulatory motion of air is created at the wingtip due to the pressure difference between the upper and lower surface of the wing is called vortices. This circulatory fluid tends to leak from lower to upper surface of wing which causes downward motion is called “downwash” and generates a component of the local lift force in the direction of the free stream called induced drag. Downwash causes reduction of lift and contribute induced drag to the total drag. Drag reduction for aerial vehicles has a range of positive ramifications: reduced fuel consumption, larger operational range, greater endurance and higher achievable speeds. An experimental study is conducted to examine the potentiality of slotted winglet for the reduction of induced drag, and for the improvement of lift coefficient without increasing the span of aircraft wing. The model composed of a swept wing built from NACA 0012 airfoil. The test conducted in subsonic wind tunnel of 1m×1m rectangular test section at flow speed 25m/s placing the wing without winglet, wing with winglet at 30° inclination, wing with winglet at 60° inclination, and wing with winglet at 70° inclination at angle of attack ranging from 0 to 16 degree. The test result shows 20- 25% reduction in drag coefficient and 10-20% increase in lift coefficient by using slotted winglet.

  2. Slotted Aircraft Wing

    Science.gov (United States)

    McLean, James D. (Inventor); Witkowski, David P. (Inventor); Campbell, Richard L. (Inventor)

    2006-01-01

    A swept aircraft wing includes a leading airfoil element and a trailing airfoil element. At least one full-span slot is defined by the wing during at least one transonic condition of the wing. The full-span slot allows a portion of the air flowing along the lower surface of the leading airfoil element to split and flow over the upper surface of the trailing airfoil element so as to achieve a performance improvement in the transonic condition.

  3. Numerical Investigation on Aerodynamic Characteristics of Box-wing Unmanned Aerial Vehicle%盒式翼无人机气动特性数值计算分析

    Institute of Scientific and Technical Information of China (English)

    刘毅; 靳宏斌

    2014-01-01

    传统方法求解盒式翼无人机的气动特性有一定的局限性,某无人机采用负交错的盒式翼布局,翼尖高差约为5%展长,翼面系统各部件之间的干扰影响复杂。为了获得其失速特性、升降舵效率等粘性作用强烈的边界气动特性,通过雷诺平均Navior-Stokes方法分析其极曲线、失速特性和俯仰力矩特性。结果表明:诱导阻力相对同等单翼降低约9%,与理论结果接近;后翼采用-4°的有效负安装角,导致配平后最大升力系数降低较多;大迎角失速时出现抬头力矩,与前翼后掠导致的翼尖失速以及后翼位于前翼尾流中效率降低有关。%Solving aerodynamic characteristics of box-wing unmanned aerial vehicle(UAV)by traditional methods is of certain limitations .For a box-wing UAV using negative stagger and wing tip gap of 5% wing span ,the strong interference exist between components of the wing systems .In order to study boundary aerodynamic characteristics effected strongly by viscous interaction of box-wing UAV ,which concludes stall characteristics and efficiency of elevator etc .,Reynolds Averaged Navior-Stokes scheme is adopted to analyze its drag polar , stall and pitching moment characteristics .The research reveals that the induced drag is reduced by 9% com-pared with equal mono-wing ,which is close to the theoretical result ;The trimmed maximum lift coefficient drops significantly due to the requirements of static stability and trim ,which are realized by -4° negative instal-ling angle of aft wing ;Nose up pitching moment is observed at large angle of attack after stall ,which attributes to the forward wing tip stall due to its sweptback ,as well as the decreased efficiency of the aft wing in the wake of the forward wing .

  4. Analysis of Low Speed Stall Aerodynamics of a Swept Wing with Laminar Flow Glove

    Science.gov (United States)

    Bui, Trong T.

    2014-01-01

    Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) analysis was conducted to study the low-speed stall aerodynamics of a GIII aircraft's swept wing modified with a laminar-flow wing glove. The stall aerodynamics of the gloved wing were analyzed and compared with the unmodified wing for the flight speed of 120 knots and altitude of 2300 ft above mean sea level (MSL). The Star-CCM+ polyhedral unstructured CFD code was first validated for wing stall predictions using the wing-body geometry from the First American Institute of Aeronautics and Astronautics (AIAA) CFD High-Lift Prediction Workshop. It was found that the Star-CCM+ CFD code can produce results that are within the scattering of other CFD codes considered at the workshop. In particular, the Star-CCM+ CFD code was able to predict wing stall for the AIAA wing-body geometry to within 1 degree of angle of attack as compared to benchmark wind-tunnel test data. Current results show that the addition of the laminar-flow wing glove causes the gloved wing to stall much earlier than the unmodified wing. Furthermore, the gloved wing has a different stall characteristic than the clean wing, with no sharp lift drop-off at stall for the gloved wing.

  5. Analysis of Low-Speed Stall Aerodynamics of a Swept Wing with Laminar-Flow Glove

    Science.gov (United States)

    Bui, Trong T.

    2014-01-01

    Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) analysis was conducted to study the low-speed stall aerodynamics of a GIII aircraft's swept wing modified with a laminar-flow wing glove. The stall aerodynamics of the gloved wing were analyzed and compared with the unmodified wing for the flight speed of 120 knots and altitude of 2300 ft above mean sea level (MSL). The Star-CCM+ polyhedral unstructured CFD code was first validated for wing stall predictions using the wing-body geometry from the First American Institute of Aeronautics and Astronautics (AIAA) CFD High-Lift Prediction Workshop. It was found that the Star-CCM+ CFD code can produce results that are within the scattering of other CFD codes considered at the workshop. In particular, the Star-CCM+ CFD code was able to predict wing stall for the AIAA wing-body geometry to within 1 degree of angle of attack as compared to benchmark wind-tunnel test data. Current results show that the addition of the laminar-flow wing glove causes the gloved wing to stall much earlier than the unmodified wing. Furthermore, the gloved wing has a different stall characteristic than the clean wing, with no sharp lift drop-off at stall for the gloved wing.

  6. Wing Warping, Roll Control and Aerodynamic Optimization of Inflatable Wings

    Science.gov (United States)

    Simpson, Andrew

    2005-11-01

    The research presents work on aerodynamic control by warping inflatable wings. Inflatable wings are deformable by their nature. Mechanical manipulation of the wing's shape has been demonstrated to alter the performance and control the vehicle in flight by deforming the trailing edge of the wing near the wing tip. Predicting and correlating the forces required in deforming the wings to a particular shape and the deformation generated for a given internal pressure were conducted through the use of photogrammetry. This research focuses on optimizing the roll moments and aerodynamic performance of the vehicle, given the current level of wing warping ability. Predictions from lifting line theory applied to wing shape changes are presented. Comparisons from the experimental results are made with lifting line analysis for wings with arbitrary twist and the solutions are used to determine rolling moment and optimum L/D. Results from flight tests will also be presented.

  7. Optimization of Kinematics of a Flapping Wing Mechanism

    Science.gov (United States)

    George, Ryan; Thomson, Scott; Mattson, Christopher; Colton, Mark; Tree, Mike

    2010-11-01

    Flapping flight offers several potential advantages over conventional fixed wing flight, such as agility and maneuverability in confined spaces, potentially decreased noise and detectability, and hovering capability. In this presentation, a water tunnel-based flapping wing apparatus is introduced that allows for arbitrary wing trajectories in three rotational degrees of freedom and simultaneous measurements of lift and thrust production. An optimal flapping trajectory for takeoff is found using hardware-in-the-loop optimization methodology. Wing motion derived from high-speed imaging of a ladybug during takeoff is used as a first iteration of the hardware-in-the-loop optimization. Using real-time force measurements and a gradient-based optimization approach, the algorithm searches for the optimal trajectory for a variety of parameters such as lift or efficiency. Hardware performance is assessed. Results from the optimization routine, including the final flapping trajectory are reported for both rigid and compliant wings.

  8. Physical properties of the benchmark models program supercritical wing

    Science.gov (United States)

    Dansberry, Bryan E.; Durham, Michael H.; Bennett, Robert M.; Turnock, David L.; Silva, Walter A.; Rivera, Jose A., Jr.

    1993-01-01

    The goal of the Benchmark Models Program is to provide data useful in the development and evaluation of aeroelastic computational fluid dynamics (CFD) codes. To that end, a series of three similar wing models are being flutter tested in the Langley Transonic Dynamics Tunnel. These models are designed to simultaneously acquire model response data and unsteady surface pressure data during wing flutter conditions. The supercritical wing is the second model of this series. It is a rigid semispan model with a rectangular planform and a NASA SC(2)-0414 supercritical airfoil shape. The supercritical wing model was flutter tested on a flexible mount, called the Pitch and Plunge Apparatus, that provides a well-defined, two-degree-of-freedom dynamic system. The supercritical wing model and associated flutter test apparatus is described and experimentally determined wind-off structural dynamic characteristics of the combined rigid model and flexible mount system are included.

  9. Active Control of Flapping Wings Using Wing Deformation

    Science.gov (United States)

    Tokutake, Hiroshi; Sunada, Shigeru; Ohtsuka, Yukio

    A new method for the attitude control of a flapping-wing aircraft is proposed. In this method, the variations in wing deformation, that is, the feathering angle and the camber, are controlled by pulling the wing at a certain point with a thread connected to a servomotor. The experimental setup for verifying the practicability of this method was developed, and aerodynamic forces and wing deformation were measured. It was concluded that thread control caused effective wing deformation, and the variation in the deformation generated the pitching moment that controls the attitude of a flapping-wing aircraft.

  10. Flow field of flexible flapping wings

    Science.gov (United States)

    Sallstrom, Erik

    The agility and maneuverability of natural fliers would be desirable to incorporate into engineered micro air vehicles (MAVs). However, there is still much for engineers to learn about flapping flight in order to understand how such vehicles can be built for efficient flying. The goal of this study is to develop a methodology for capturing high quality flow field data around flexible flapping wings in a hover environment and to interpret it to gain a better understanding of how aerodynamic forces are generated. The flow field data was captured using particle image velocimetry (PIV) and required that measurements be taken around a repeatable flapping motion to obtain phase-averaged data that could be studied throughout the flapping cycle. Therefore, the study includes the development of flapping devices with a simple repeatable single degree of freedom flapping motion. The acquired flow field data has been examined qualitatively and quantitatively to investigate the mechanisms behind force production in hovering flight and to relate it to observations in previous research. Specifically, the flow fields have been investigated around a rigid wing and several carbon fiber reinforced flexible membrane wings. Throughout the whole study the wings were actuated with either a sinusoidal or a semi-linear flapping motion. The semi-linear flapping motion holds the commanded angular velocity nearly constant through half of each half-stroke while the sinusoidal motion is always either accelerating or decelerating. The flow fields were investigated by examining vorticity and vortex structures, using the Q criterion as the definition for the latter, in two and three dimensions. The measurements were combined with wing deflection measurements to demonstrate some of the key links in how the fluid-structure interactions generated aerodynamic forces. The flow fields were also used to calculate the forces generated by the flapping wings using momentum balance methods which yielded

  11. Aeroelastic Tailoring of Transport Wings Including Transonic Flutter Constraints

    Science.gov (United States)

    Stanford, Bret K.; Wieseman, Carol D.; Jutte, Christine V.

    2015-01-01

    Several minimum-mass optimization problems are solved to evaluate the effectiveness of a variety of novel tailoring schemes for subsonic transport wings. Aeroelastic stress and panel buckling constraints are imposed across several trimmed static maneuver loads, in addition to a transonic flutter margin constraint, captured with aerodynamic influence coefficient-based tools. Tailoring with metallic thickness variations, functionally graded materials, balanced or unbalanced composite laminates, curvilinear tow steering, and distributed trailing edge control effectors are all found to provide reductions in structural wing mass with varying degrees of success. The question as to whether this wing mass reduction will offset the increased manufacturing cost is left unresolved for each case.

  12. A Brief Study, Research, Design, Analysis on Multi Section Variable Camber Wing

    Directory of Open Access Journals (Sweden)

    ArimalaParamasivamSruthi

    2015-08-01

    Full Text Available Minimizing fuel consumption is one of the major concerns in the aviation industry. In the past decade, there have been many attempts to improve the fuel efficiency of aircraft. One of the methods proposed is to vary the lift-to-drag ratio of the aircraft in different flight conditions. To achieve this, the wing of the airplane must be able to change its configuration during flight, corresponding to different flight regimes.In the research presented in this thesis, the aerodynamic characteristics of a multisection, variable camber wing were investigated. The model used in this research had a 160mm chord and a 200mm wingspan, with the ribs divided into 4 sections. Each section was able to rotate approximately 5 degrees without causing significant discontinuity on the wing surface. Two pneumatic actuators located at the main spar were used to morph the wing through mechanical linkages. The multi-section variable camber wing model could provide up to 10 percent change in camber from the baseline configuration, which had a NACA0015 section.The wing was tested in the free-jet wind tunnel at three different Reynolds numbers: 322000, 48000, and 636000. Static tests were performed to obtain lift and drag data for different configurations. Two rigid wings in baseline and camber configuration were built and tested to compare the test data with variable camber wing. The wind tunnel test results indicated that the multisection variable camber wing provided a higher lift than the rigid wing in both configurations whereas high drag was also generated on the variable camber wing due to friction drag on the wing skin. The larger drag value appeared on variable camber wing in baseline configuration than in cambered configuration resulting in lower lift-to-drag ratio as compared to the baseline rigid wing whereas the variable camber wing in cambered configuration had higher lift-to-drag ratio than the cambered rigid wing.

  13. Efficient passive pitching motion caused by elastic deformation in flexible flapping wing MAVs

    Science.gov (United States)

    Nguyen, Trong; Truong, Tien; Yeo, Khoon Seng; Lim, Tee Tai

    2015-11-01

    Computational and experimental models which mimic Hawkmoth wings were constructed to investigate the effects of wing flexibility. The wing actuation mechanism is minimal with only one degree of freedom in sweeping motion with neither active pitching nor elevation. Despite the simplicity of the imparted motion, the wing models in both computations and experiments delivered convincing deformation features such as wing twisting and camber which closely resembles the ones observed in real Hawkmoth wings. The generated aerodynamic forces are remarkable both in magnitude and efficiency. The study hence reveals that a complicated actuation mechanism might not be required to produce the sophisticated and efficient motion of insect wings, which in fact could be the result of collective elastic deformation thanks to their highly optimized structure mainly comprised of well-organized veins and membranes.

  14. Twin Flavor Chicken Wings

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    Ingredients:1000g chicken wings,about,100g Shredded rape-seedleaves,100g black sesame seeds,7g salt,5g sugar,3gMSG,10g cooking wine,5g cassia bark,1000g cookingoil(actual consumption only 100 grams),one egg,anoptional amount of scallion,ginger root,starch and

  15. A bio-inspired study on tidal energy extraction with flexible flapping wings.

    Science.gov (United States)

    Liu, Wendi; Xiao, Qing; Cheng, Fai

    2013-09-01

    Previous research on the flexible structure of flapping wings has shown an improved propulsion performance in comparison to rigid wings. However, not much is known about this function in terms of power efficiency modification for flapping wing energy devices. In order to study the role of the flexible wing deformation in the hydrodynamics of flapping wing energy devices, we computationally model the two-dimensional flexible single and twin flapping wings in operation under the energy extraction conditions with a large Reynolds number of 106. The flexible motion for the present study is predetermined based on a priori structural result which is different from a passive flexibility solution. Four different models are investigated with additional potential local distortions near the leading and trailing edges. Our simulation results show that the flexible structure of a wing is beneficial to enhance power efficiency by increasing the peaks of lift force over a flapping cycle, and tuning the phase shift between force and velocity to a favourable trend. Moreover, the impact of wing flexibility on efficiency is more profound at a low nominal effective angle of attack (AoA). At a typical flapping frequency f * = 0.15 and nominal effective AoA of 10°, a flexible integrated wing generates 7.68% higher efficiency than a rigid wing. An even higher increase, around six times that of a rigid wing, is achievable if the nominal effective AoA is reduced to zero degrees at feathering condition. This is very attractive for a semi-actuated flapping energy system, where energy input is needed to activate the pitching motion. The results from our dual-wing study found that a parallel twin-wing device can produce more power compared to a single wing due to the strong flow interaction between the two wings.

  16. SMA actuators for morphing wings

    Science.gov (United States)

    Brailovski, V.; Terriault, P.; Georges, T.; Coutu, D.

    An experimental morphing laminar wing was developed to prove the feasibility of aircraft fuel consumption reduction through enhancement of the laminar flow regime over the wing extrados. The morphing wing prototype designed for subsonic cruise flight conditions (Mach 0.2 … 0.3; angle of attack - 1 … +2∘), combines three principal subsystems: (1) flexible extrados, (2) rigid intrados and (3) an actuator group located inside the wing box. The morphing capability of the wing relies on controlled deformation of the wing extrados under the action of shape memory alloys (SMA) actuators. A coupled fluid-structure model of the morphing wing was used to evaluate its mechanical and aerodynamic performances in different flight conditions. A 0.5 m chord and 1 m span prototype of the morphing wing was tested in a subsonic wind tunnel. In this work, SMA actuators for morphing wings were modeled using a coupled thermo-mechanical finite element model and they were windtunnel validated. If the thermo-mechanical model of SMA actuators presented in this work is coupled with the previously developed structureaerodynamic model of the morphing wing, it could serve for the optimization of the entire morphing wing system.

  17. When wings touch wakes: understanding locomotor force control by wake wing interference in insect wings.

    Science.gov (United States)

    Lehmann, Fritz-Olaf

    2008-01-01

    Understanding the fluid dynamics of force control in flying insects requires the exploration of how oscillating wings interact with the surrounding fluid. The production of vorticity and the shedding of vortical structures within the stroke cycle thus depend on two factors: the temporal structure of the flow induced by the wing's own instantaneous motion and the flow components resulting from both the force production in previous wing strokes and the motion of other wings flapping in close proximity. These wake-wing interactions may change on a stroke-by-stroke basis, confronting the neuro-muscular system of the animal with a complex problem for force control. In a single oscillating wing, the flow induced by the preceding half stroke may lower the wing's effective angle of attack but permits the recycling of kinetic energy from the wake via the wake capture mechanism. In two-winged insects, the acceleration fields produced by each wing may strongly interact via the clap-and-fling mechanism during the dorsal stroke reversal. Four-winged insects must cope with the fact that the flow over their hindwings is affected by the presence of the forewings. In these animals, a phase-shift between the stroke cycles of fore- and hindwing modulates aerodynamic performance of the hindwing via leading edge vortex destruction and changes in local flow condition including wake capture. Moreover, robotic wings demonstrate that phase-lag during peak performance and the strength of force modulation depend on the vertical spacing between the two stroke planes and the size ratio between fore- and hindwing. This study broadly summarizes the most prominent mechanisms of wake-wing and wing-wing interactions found in flapping insect wings and evaluates the consequences of these processes for the control of locomotor forces in the behaving animal.

  18. A novel posture alignment system for aircraft wing assembly

    Institute of Scientific and Technical Information of China (English)

    Bin ZHANG; Bao-guo YAO; Ying-lin KE

    2009-01-01

    A novel 6-degree of freedom (DOF) posture alignment system, based on 3-DOF positioners, is presented for the assembly of aircraft wings. Each positioner is connected with the wing through a rotational and adsorptive half-ball shaped end-effector, and the positioners together with the wing are considered as a 3-PPPS (P denotes a prismatic joint and S denotes a spherical joint) redundantly actuated parallel mechanism. The kinematic model of this system is established and a trajectory planning method is introduced. A complete analysis of inverse dynamics is carried out with the Newton-Euler algorithm, which is used to find the desired actuating torque in the design and path planning phase. Simulation analysis of the displacement and actuating torque of each joint of the positioners based on inverse kinematics and dynamics is conducted, and the results show that the system is feasible for the posture alignment of aircraft wings.

  19. Wing Kinematics and Wake Velocity Characteristics of Bat Flight

    Science.gov (United States)

    Swartz, Sharon

    2005-11-01

    Bats demonstrate unequalled flight characteristics and are capable of highly efficient flight as well as extreme maneuverability at high speeds. They have morphological properties that are unique in the animal world including jointed wings skeletons, elastic wing membranes and very complex wing motions. We report on a series of experiments on bats flying in a flight cage along both a straight path and through a 90-degree turn. Measurements of their kinematic wing motion (using high speed photography) and wake velocity structures (using stereo PIV) are reported. The live animal measurements are also interpreted with the help of a series of companion wind tunnel experiments using model structures that mimic some key features of bat flight mechanics. The results reveal a complex vortex wake structure which is compared and contrasted to that found in bird and insect flight.

  20. Experimental Investigation of wing-tip vortex evolution in turbulence

    Science.gov (United States)

    Bailey, Sean; Ghimire, Hari

    2016-11-01

    Towing tank experiments were conducted to examine the evolution of a wing-tip vortex in grid-generated turbulence. Measurements using particle image velocimetry (PIV) were conducted of the velocity field generated by towing a semi-span symmetric wing oriented at 8 degree angle of attack. Turbulence of different kinetic energy and length scales was produced by simultaneously towing grids of different mesh sizes upstream of the wing. Results showed that wing-tip vortex wandering increased with the increase in turbulence kinetic energy, ultimately leading to spontaneous collapse of the vortex. During this process, a measurable diffusion of overall vortex circulation was observed, with the rate of diffusion leading to the collapse of the vortex dependent on the turbulence intensity. Interestingly, the radius of the vortex core remained largely unchanged during the diffusion process, Evidence suggests that the breakdown of vortex was enhanced by entrainment of fluid inside vortex core due to vortex stripping in presence of turbulence.

  1. Design optimization of deployable wings

    Science.gov (United States)

    Gaddam, Pradeep

    Morphing technology is an important aspect of UAV design, particularly in regards to deployable systems. The design of such system has an important impact on the vehicle's performance. The primary focus of the present research work was to determine the most optimum deployable wing design from 3 competing designs and develop one of the deployable wing designs to test in the research facility. A Matlab code was developed to optimize 3 deployable wing concepts inflatable, inflatable telescopic and rigid-folding wings based on a sequential optimization strategy. The constraints that were part of the code include the packaging constraints during its stowed state, fixed length of the deployed section and the minimum L/D constraint. This code resulted in determining the optimum weight of all the 3 designs, the most optimum weight design is the inflatable wing design. This is a result of the flexible skin material and also due to no rigid parts in the deployed wing section. Another goal of the research involved developing an inflatable telescopic wing. The prototype was tested in a wind tunnel, while the actual wing was tested in the altitude chamber to determine the deployment speed, input pressure, analyze and predict the deployment sequence and behavior of the wing at such high wind speeds and altitudes ranging from 60,000 ft to 90,000 ft. Results from these tests allowed us to conclude the deployment sequence of the telescopic wing followed from the root to the tip section. The results were used to analyze the deployment time of the wing. As expected the deployment time decreased with an increase in input pressure. The results also show us that as the altitude increases, the deployment speed of the wing also increased. This was demonstrated when the wing was tested at a maximum altitude pressure of 90,000ft, well above the design altitude of 60,000ft.

  2. Ornithopter Type Flapping Wings for Autonomous Micro Air Vehicles

    Directory of Open Access Journals (Sweden)

    Sutthiphong Srigrarom

    2015-05-01

    resonance phenomenon of a two-degree of freedom elastic system, that is, the wing is supported by the springs for flapping and feathering motions. Being oscillated close to the resonance frequency of the system, only by the torque in flapping motion, the amplitude gained is a few times higher than that of normal case. The first prototype was made from acrylic using a laser cutting machine. The wings were made up of carbon rods and kite material Ripstop. First test showed that the wings were too heavy for the mechanism to work. The third prototype was a smaller single gear crank design which was fabricated using a 3D printer. Initial test proved that the second prototype could withstand the high frequency flapping and near resonance amplitude as designed. With remote control, the third prototype was able to take off, climb, cruise and land in flapping mode successfully.

  3. Circulation Produced by a Flapping Wing During Stroke Reversal

    Science.gov (United States)

    Burge, Matthew; Ringuette, Matthew

    2016-11-01

    We investigate the circulation behavior of the 3D flow structures formed during the stroke-reversal of a 2-degree-of-freedom flapping wing in hover. Previous work has related circulation peaks to the unsteady wing kinematics and forces. However, information from experiments detailing contributions from the multiple, 3D flow structures is lacking. The objective of this work is to quantitatively study the spanwise circulation as well as the spanwise flow which advects vorticity in the complex loop topology of a flapping wing during stroke reversal. We analyze the flow features of a scaled wing model using multi-plane stereo digital particle image velocimetry in a glycerin-water mixture. Data plane locations along the wing span are inspired by the time-resolved behavior of the 3D vortex structures observed in our earlier flow visualization studies. As with our prior work, we vary dimensionless parameters such as the pitching reduced frequency to understand their effect on the circulation. This research provides insight into the vortex dynamics produced by the coupled rotational and pitching wing motions during stroke reversal, when lift generation is challenging. This work is supported by the National Science Foundation, Award Number 1336548, supervised by Dr. Dimitrios Papavassiliou.

  4. Integration effects of pylon geometry on a high-wing transport airplane

    Science.gov (United States)

    Carlson, John R.; Lamb, Milton

    1989-01-01

    An investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the installation effects of a series of pylons that had differing cross-sectional shapes on the pressure distributions and aerodynamic characteristics of a 1/24-scale high wing transport. The tests were conducted at Mach numbers at 0.70 and 0.80 at angles of attack from -3 degrees to 4 degrees with the pylons tested at various toe angles between 5 degrees inboard and 5 degrees outboard. Results of this study indicate that the installed drag was lowest for the pylons with a compression pylon type design which kept the flow under the wing in the pylon/wing junction comparable to the clean wing velocities.

  5. Automated measurement of Drosophila wings

    Directory of Open Access Journals (Sweden)

    Mezey Jason

    2003-12-01

    Full Text Available Abstract Background Many studies in evolutionary biology and genetics are limited by the rate at which phenotypic information can be acquired. The wings of Drosophila species are a favorable target for automated analysis because of the many interesting questions in evolution and development that can be addressed with them, and because of their simple structure. Results We have developed an automated image analysis system (WINGMACHINE that measures the positions of all the veins and the edges of the wing blade of Drosophilid flies. A video image is obtained with the aid of a simple suction device that immobilizes the wing of a live fly. Low-level processing is used to find the major intersections of the veins. High-level processing then optimizes the fit of an a priori B-spline model of wing shape. WINGMACHINE allows the measurement of 1 wing per minute, including handling, imaging, analysis, and data editing. The repeatabilities of 12 vein intersections averaged 86% in a sample of flies of the same species and sex. Comparison of 2400 wings of 25 Drosophilid species shows that wing shape is quite conservative within the group, but that almost all taxa are diagnosably different from one another. Wing shape retains some phylogenetic structure, although some species have shapes very different from closely related species. The WINGMACHINE system facilitates artificial selection experiments on complex aspects of wing shape. We selected on an index which is a function of 14 separate measurements of each wing. After 14 generations, we achieved a 15 S.D. difference between up and down-selected treatments. Conclusion WINGMACHINE enables rapid, highly repeatable measurements of wings in the family Drosophilidae. Our approach to image analysis may be applicable to a variety of biological objects that can be represented as a framework of connected lines.

  6. Stiffness of desiccating insect wings

    Energy Technology Data Exchange (ETDEWEB)

    Mengesha, T E; Vallance, R R [Department of Mechanical Engineering, The George Washington University, 738 Phillips Hall, 801 22nd St NW, Washington, DC 20052 (United States); Mittal, R, E-mail: vallance@gwu.edu [Department of Mechanical Engineering, Johns Hopkins University, 126 Latrobe Hall, 3400 N Charles Street, Baltimore, MD 21218 (United States)

    2011-03-15

    The stiffness of insect wings is typically determined through experimental measurements. Such experiments are performed on wings removed from insects. However, the wings are subject to desiccation which typically leads to an increase in their stiffness. Although this effect of desiccation is well known, a comprehensive study of the rate of change in stiffness of desiccating insect wings would be a significant aid in planning experiments as well as interpreting data from such experiments. This communication presents a comprehensive experimental analysis of the change in mass and stiffness of gradually desiccating forewings of Painted Lady butterflies (Vanessa cardui). Mass and stiffness of the forewings of five butterflies were simultaneously measured every 10 min over a 24 h period. The averaged results show that wing mass declined exponentially by 21.1% over this time period with a time constant of 9.8 h, while wing stiffness increased linearly by 46.2% at a rate of 23.4 {mu}N mm{sup -1} h{sup -1}. For the forewings of a single butterfly, the experiment was performed over a period of 1 week, and the results show that wing mass declined exponentially by 52.2% with a time constant of 30.2 h until it reached a steady-state level of 2.00 mg, while wing stiffness increased exponentially by 90.7% until it reached a steady-state level of 1.70 mN mm{sup -1}. (communication)

  7. Aerodynamic performance and particle image velocimetery of piezo actuated biomimetic manduca sexta engineered wings towards the design and application of a flapping wing flight vehicle

    Science.gov (United States)

    DeLuca, Anthony M.

    Considerable research and investigation has been conducted on the aerodynamic performance, and the predominate flow physics of the Manduca Sexta size of biomimetically designed and fabricated wings as part of the AFIT FWMAV design project. Despite a burgeoning interest and research into the diverse field of flapping wing flight and biomimicry, the aerodynamics of flapping wing flight remains a nebulous field of science with considerable variance into the theoretical abstractions surrounding aerodynamic mechanisms responsible for aerial performance. Traditional FWMAV flight models assume a form of a quasi-steady approximation of wing aerodynamics based on an infinite wing blade element model (BEM). An accurate estimation of the lift, drag, and side force coefficients is a critical component of autonomous stability and control models. This research focused on two separate experimental avenues into the aerodynamics of AFIT's engineered hawkmoth wings|forces and flow visualization. 1. Six degree of freedom force balance testing, and high speed video analysis was conducted on 30°, 45°, and 60° angle stop wings. A novel, non-intrusive optical tracking algorithm was developed utilizing a combination of a Gaussian Mixture Model (GMM) and ComputerVision (OpenCV) tools to track the wing in motion from multiple cameras. A complete mapping of the wing's kinematic angles as a function of driving amplitude was performed. The stroke angle, elevation angle, and angle of attack were tabulated for all three wings at driving amplitudes ranging from A=0.3 to A=0.6. The wing kinematics together with the force balance data was used to develop several aerodynamic force coefficient models. A combined translational and rotational aerodynamic model predicted lift forces within 10%, and vertical forces within 6%. The total power consumption was calculated for each of the three wings, and a Figure of Merit was calculated for each wing as a general expression of the overall efficiency of

  8. Beetle wings are inflatable origami

    Science.gov (United States)

    Chen, Rui; Ren, Jing; Ge, Siqin; Hu, David

    2015-11-01

    Beetles keep their wings folded and protected under a hard shell. In times of danger, they must unfold them rapidly in order for them to fly to escape. Moreover, they must do so across a range of body mass, from 1 mg to 10 grams. How can they unfold their wings so quickly? We use high-speed videography to record wing unfolding times, which we relate to the geometry of the network of blood vessels in the wing. Larger beetles have longer unfolding times. Modeling of the flow of blood through the veins successfully accounts for the wing unfolding speed of large beetles. However, smaller beetles have anomalously short unfolding times, suggesting they have lower blood viscosity or higher driving pressure. The use of hydraulics to unfold complex objects may have implications in the design of micro-flying air vehicles.

  9. AERODYNAMICS OF WING TIP SAILS

    Directory of Open Access Journals (Sweden)

    MUSHTAK AL-ATABI

    2006-06-01

    Full Text Available Observers have always been fascinated by soaring birds. An interesting feature of these birds is the existence of few feathers extending from the tip of the wing. In this paper, small lifting surfaces were fitted to the tip of a NACA0012 wing in a fashion similar to that of wing tip feathers. Experimental measurements of induced drag, longitudinal static stability and trailing vortex structure were obtained.The tests showed that adding wing tip surfaces (sails decreased the induced drag factor and increased the longitudinal static stability. Results identified two discrete appositely rotated tip vortices and showed the ability of wing tip surfaces to break them down and to diffuse them.

  10. Dynamic distributions and population declines of Golden-winged Warblers

    Science.gov (United States)

    Rosenberg, Kenneth V.; Will, Tom; Buehler, David A.; Barker Swarthout, Sara; Thogmartin, Wayne E.; Chandler, Richard

    2016-01-01

    With an estimated breeding population in 2010 of 383,000 pairs, the Golden-winged Warbler (Vermivora chrysoptera) is among the most vulnerable and steeply declining of North American passerines. This species also has exhibited among the most dynamic breeding distributions, with populations expanding and then contracting over the past 150 years in response to regional habitat changes, interactions with closely related Blue-winged Warblers (V. cyanoptera), and possibly climate change. Since 1966, the rangewide population has declined by >70% (-2.3% per year; latest North American Breeding Bird Survey data), with much steeper declines in the Appalachian Mountains bird conservation region (-8.3% per year, 98% overall decline). Despite apparently stable or increasing populations in the northwestern part of the range (Minnesota, Manitoba), population estimates for Golden-winged Warbler have continued to decline by 18% from the decade of the 1990s to the 2000s. Population modeling predicts a further decline to roughly 37,000 individuals by 2100, with the species likely to persist only in Manitoba, Minnesota, and possibly Ontario. To delineate the present-day distribution and to identify population concentrations that could serve as conservation focus areas, we compiled rangewide survey data collected in 2000-2006 in 21 states and 3 Canadian provinces, as part of the Golden-winged Warbler Atlas Project (GOWAP), supplemented by state and provincial Breeding Bird Atlas data and more recent observations in eBird. Based on >8,000 GOWAP surveys for Golden-winged and Blue-winged warblers and their hybrids, we mapped occurrence of phenotypically pure and mixed populations in a roughly 0.5-degree grid across the species’ ranges. Hybrids and mixed Golden-winged-Blue-winged populations occurred in a relatively narrow zone across Minnesota, Wisconsin, Michigan, southern Ontario, and northern New York. Phenotypically pure Golden-winged Warbler populations occurred north of this

  11. Falling with Style: Bats Perform Complex Aerial Rotations by Adjusting Wing Inertia.

    Directory of Open Access Journals (Sweden)

    Attila J Bergou

    Full Text Available The remarkable maneuverability of flying animals results from precise movements of their highly specialized wings. Bats have evolved an impressive capacity to control their flight, in large part due to their ability to modulate wing shape, area, and angle of attack through many independently controlled joints. Bat wings, however, also contain many bones and relatively large muscles, and thus the ratio of bats' wing mass to their body mass is larger than it is for all other extant flyers. Although the inertia in bat wings would typically be associated with decreased aerial maneuverability, we show that bat maneuvers challenge this notion. We use a model-based tracking algorithm to measure the wing and body kinematics of bats performing complex aerial rotations. Using a minimal model of a bat with only six degrees of kinematic freedom, we show that bats can perform body rolls by selectively retracting one wing during the flapping cycle. We also show that this maneuver does not rely on aerodynamic forces, and furthermore that a fruit fly, with nearly massless wings, would not exhibit this effect. Similar results are shown for a pitching maneuver. Finally, we combine high-resolution kinematics of wing and body movements during landing and falling maneuvers with a 52-degree-of-freedom dynamical model of a bat to show that modulation of wing inertia plays the dominant role in reorienting the bat during landing and falling maneuvers, with minimal contribution from aerodynamic forces. Bats can, therefore, use their wings as multifunctional organs, capable of sophisticated aerodynamic and inertial dynamics not previously observed in other flying animals. This may also have implications for the control of aerial robotic vehicles.

  12. Assembly modes of dragonfly wings.

    Science.gov (United States)

    Zhao, Hong-Xiao; Yin, Ya-Jun; Zhong, Zheng

    2011-12-01

    The assembly modes of dragonfly wings are observed through FEG-ESEM. Different from airplane wings, dragonfly wings are found to be assembled through smooth transition mode and global package mode. First, at the vein/membrane conjunctive site, the membrane is divided into upper and lower portions from the center layer and transited smoothly to the vein. Then the two portions pack the vein around and form the outer surface of the vein. Second, at the vein/spike conjunctive site, the vein and spike are connected smoothly into a triplet. Last, at the vein/membrane/spike conjunctive site, the membrane (i.e., the outer layer of the vein) transits smoothly to the spike, packs it around, and forms its outer layer. In short, the membrane looks like a closed coat packing the wing as a whole. The smooth transition mode and the global package mode are universal assembly modes in dragonfly wings. They provide us the references for better understanding of the functions of dragonfly wings and the bionic manufactures of the wings of flights with mini sizes.

  13. Structural Analysis of a Dragonfly Wing

    NARCIS (Netherlands)

    Jongerius, S.R.; Lentink, D.

    2010-01-01

    Dragonfly wings are highly corrugated, which increases the stiffness and strength of the wing significantly, and results in a lightweight structure with good aerodynamic performance. How insect wings carry aerodynamic and inertial loads, and how the resonant frequency of the flapping wings is tuned

  14. Aeroelastic and Flight Dynamics Analysis of Folding Wing Systems

    Science.gov (United States)

    Wang, Ivan

    This dissertation explores the aeroelastic stability of a folding wing using both theoretical and experimental methods. The theoretical model is based on the existing clamped-wing aeroelastic model that uses beam theory structural dynamics and strip theory aerodynamics. A higher-fidelity theoretical model was created by adding several improvements to the existing model, namely a structural model that uses ANSYS for individual wing segment modes and an unsteady vortex lattice aerodynamic model. The comparison with the lower-fidelity model shows that the higher-fidelity model typical provides better agreement between theory and experiment, but the predicted system behavior in general does not change, reinforcing the effectiveness of the low-fidelity model for preliminary design of folding wings. The present work also conducted more detailed aeroelastic analyses of three-segment folding wings, and in particular considers the Lockheed-type configurations to understand the existence of sudden changes in predicted aeroelastic behavior with varying fold angle for certain configurations. These phenomena were observed in carefully conducted experiments, and nonlinearities---structural and geometry---were shown to suppress the phenomena. Next, new experimental models with better manufacturing tolerances are designed to be tested in the Duke University Wind Tunnel. The testing focused on various configurations of three-segment folding wings in order to obtain higher quality data. Next, the theoretical model was further improved by adding aircraft longitudinal degrees of freedom such that the aeroelastic model may predict the instabilities for the entire aircraft and not just a clamped wing. The theoretical results show that the flutter instabilities typically occur at a higher air speed due to greater frequency separation between modes for the aircraft system than a clamped wing system, but the divergence instabilities occur at a lower air speed. Lastly, additional

  15. Stall flutter and nonlinear divergence of a two-dimensional flat plate wing

    Science.gov (United States)

    Dugundji, J.; Aravamudan, K.

    1976-01-01

    Tests were conducted in a small wind tunnel to study the torsional stall flutter behavior of a two-dimensional flat-plate wing pivoted about the midchord. The nonlinear static divergence equilibrium properties of the wing were well predicted from the measured static moment characteristics. Large amplitude limit cycles ranging from plus or minus 11 degrees to plus or minus 100 degrees were observed. Stall flutter occurred above a critical value of a reduced frequency of about 2. Self-excitation occurred for initial angles of attack between 0 and 8 degrees. Nondimensional harmonic coefficients were extracted from the free transient vibration tests for amplitudes up to 80 degrees.

  16. Conceptual design and optimization methodology for box wing aircraft

    OpenAIRE

    Jemitola, Paul Olugbeji

    2012-01-01

    A conceptual design optimization methodology was developed for a medium range box wing aircraft. A baseline conventional cantilever wing aircraft designed for the same mis- sion and payload was also optimized alongside a baseline box wing aircraft. An empirical formula for the mass estimation of the fore and aft wings of the box wing aircraft was derived by relating conventional cantilever wings to box wing aircraft wings. The results indicate that the fore and aft wings would ...

  17. Optimum Wing Shape Determination of Highly Flexible Morphing Aircraft for Improved Flight Performance

    Science.gov (United States)

    Su, Weihua; Swei, Sean Shan-Min; Zhu, Guoming G.

    2016-01-01

    In this paper, optimum wing bending and torsion deformations are explored for a mission adaptive, highly flexible morphing aircraft. The complete highly flexible aircraft is modeled using a strain-based geometrically nonlinear beam formulation, coupled with unsteady aerodynamics and six-degrees-of-freedom rigid-body motions. Since there are no conventional discrete control surfaces for trimming the flexible aircraft, the design space for searching the optimum wing geometries is enlarged. To achieve high performance flight, the wing geometry is best tailored according to the specific flight mission needs. In this study, the steady level flight and the coordinated turn flight are considered, and the optimum wing deformations with the minimum drag at these flight conditions are searched by utilizing a modal-based optimization procedure, subject to the trim and other constraints. The numerical study verifies the feasibility of the modal-based optimization approach, and shows the resulting optimum wing configuration and its sensitivity under different flight profiles.

  18. WINGS Data Release

    DEFF Research Database (Denmark)

    Moretti, A.; Poggianti, B. M.; Fasano, G.;

    2014-01-01

    Context. To effectively investigate galaxy formation and evolution, it is of paramount importance to exploit homogeneous data for large samples of galaxies in different environments. Aims. The WIde-field Nearby Galaxy-cluster Survey (WINGS) project aim is to evaluate physical properties of galaxies......, and on the cluster redshift, reaching on average 90% at V ≲ 21.7. Near-infrared photometric catalogs for 26 (in K) and 19 (in J) clusters are part of the database and the number of sources is 962 344 in K and 628 813 in J. Here again the completeness depends on the data quality, but it is on average higher than 90......% for J ≲ 20.5 and K ≲ 19.4. The IR subsample with a Sersic fit comprises 71 687 objects. A morphological classification is available for 39 923 galaxies. We publish spectroscopic data, including 6132 redshifts, 5299 star formation histories, and 4381 equivalent widths. Finally, a calculation of local...

  19. Static aeroelastic analysis of composite wing

    Science.gov (United States)

    Lee, IN; Hong, Chang Sun; Miura, Hirokazu; Kim, Seung KO

    1990-01-01

    A static aeroelastic analysis capability that can predict aerodynamic loads for the deformed shape of the composite wing has been developed. The finite element method (FEM) was used for composite plate structural analysis, and the linear vortex lattice method (VLM) was used for steady aerodynamic analysis. The final deformed shape of the wing due to applied forces is determined by iterative manner using FEM and VLM. FEM and VLM analysis are related by a surface spline interpolation procedure. The wing with Gr/Ep composite material has been investigated to see the wing deformation effect. Aerodynamic load change due to wing flexibility has been investigated. Also, the effect of fiber orientation and sweep angle on the deformation pattern and aerodynamic coefficients are examined. For a certain fiber orientation, the deflection and aerodynamic loading of the composite wing is very much reduced. The swept forward wing has more significant effect of wing flexibility on aerodynamic coefficient than the swept back wing does.

  20. Diversity in the organization of elastin bundles and intramembranous muscles in bat wings.

    Science.gov (United States)

    Cheney, Jorn A; Allen, Justine J; Swartz, Sharon M

    2017-04-01

    Unlike birds and insects, bats fly with wings composed of thin skin that envelops the bones of the forelimb and spans the area between the limbs, digits, and sometimes the tail. This skin is complex and unusual; it is thinner than typical mammalian skin and contains organized bundles of elastin and embedded skeletal muscles. These elements are likely responsible for controlling the shape of the wing during flight and contributing to the aerodynamic capabilities of bats. We examined the arrangement of two macroscopic architectural elements in bat wings, elastin bundles and wing membrane muscles, to assess the diversity in bat wing skin morphology. We characterized the plagiopatagium and dactylopatagium of 130 species from 17 families of bats using cross-polarized light imaging. This method revealed structures with distinctive relative birefringence, heterogeneity of birefringence, variation in size, and degree of branching. We used previously published anatomical studies and tissue histology to identify birefringent structures, and we analyzed their architecture across taxa. Elastin bundles, muscles, neurovasculature, and collagenous fibers are present in all species. Elastin bundles are oriented in a predominantly spanwise or proximodistal direction, and there are five characteristic muscle arrays that occur within the plagiopatagium, far more muscle than typically recognized. These results inform recent functional studies of wing membrane architecture, support the functional hypothesis that elastin bundles aid wing folding and unfolding, and further suggest that all bats may use these architectural elements for flight. All species also possess numerous muscles within the wing membrane, but the architecture of muscle arrays within the plagiopatagium varies among families. To facilitate present and future discussion of these muscle arrays, we refine wing membrane muscle nomenclature in a manner that reflects this morphological diversity. The architecture of the

  1. Effect of torsional stiffness and inertia on the dynamics of low aspect ratio flapping wings.

    Science.gov (United States)

    Xiao, Qing; Hu, Jianxin; Liu, Hao

    2014-03-01

    Micro air vehicle-motivated aerodynamics in biological flight has been an important subject in the past decade. Inspired by the novel flapping wing mechanisms in insects, birds and bats, we have carried out a numerical study systematically investigating a three-dimensional flapping rigid wing with passively actuated lateral and rotational motion. Distinguishing it from the limited existing studies, this work performs a systematic examination on the effects of wing aspect ratio (AR = 1.0 to infinity), inertia (density ratio σ = 4-32), torsional stiffness (frequency ratio F = 1.5-10 and infinity) and pivot point (from chord-center to leading edge) on the dynamics response of a low AR rectangular wing under an initial zero speed flow field condition. The simulation results show that the symmetry breakdown of the flapping wing results in a forward/backward motion with a rotational pitching. When the wing reaches its stable periodic state, the induced pitching frequency is identical to its forced flapping frequency. However, depending on various kinematic and dynamic system parameters, (i.e. flapping frequency, density ratio and pitching axis), the lateral induced velocity shows a number of different oscillating frequencies. Furthermore, compared with a one degree of freedom (DoF) wing in the lateral direction only, the propulsion performance of such a two DoF wing relies very much on the magnitude of torsional stiffness adding on the pivot point, as well as its pitching axis. In all cases examined here, thrust force and moment generated by a long span wing is larger than that of a short wing, which is remarkably linked to the strong reverse von Kármán vortex street formed in the wake of a wing.

  2. Trim and Structural Optimization of Subsonic Transport Wings Using Nonconventional Aeroelastic Tailoring

    Science.gov (United States)

    Stanford, Bret K.; Jutte, Christine V.

    2014-01-01

    Several minimum-mass aeroelastic optimization problems are solved to evaluate the effectiveness of a variety of novel tailoring schemes for subsonic transport wings. Aeroelastic strength and panel buckling constraints are imposed across a variety of trimmed maneuver loads. Tailoring with metallic thickness variations, functionally graded materials, composite laminates, tow steering, and distributed trailing edge control effectors are all found to provide reductions in structural wing mass with varying degrees of success. The question as to whether this wing mass reduction will offset the increased manufacturing cost is left unresolved for each case.

  3. Design, realization and structural testing of a compliant adaptable wing

    Science.gov (United States)

    Molinari, G.; Quack, M.; Arrieta, A. F.; Morari, M.; Ermanni, P.

    2015-10-01

    This paper presents the design, optimization, realization and testing of a novel wing morphing concept, based on distributed compliance structures, and actuated by piezoelectric elements. The adaptive wing features ribs with a selectively compliant inner structure, numerically optimized to achieve aerodynamically efficient shape changes while simultaneously withstanding aeroelastic loads. The static and dynamic aeroelastic behavior of the wing, and the effect of activating the actuators, is assessed by means of coupled 3D aerodynamic and structural simulations. To demonstrate the capabilities of the proposed morphing concept and optimization procedure, the wings of a model airplane are designed and manufactured according to the presented approach. The goal is to replace conventional ailerons, thus to achieve controllability in roll purely by morphing. The mechanical properties of the manufactured components are characterized experimentally, and used to create a refined and correlated finite element model. The overall stiffness, strength, and actuation capabilities are experimentally tested and successfully compared with the numerical prediction. To counteract the nonlinear hysteretic behavior of the piezoelectric actuators, a closed-loop controller is implemented, and its capability of accurately achieving the desired shape adaptation is evaluated experimentally. Using the correlated finite element model, the aeroelastic behavior of the manufactured wing is simulated, showing that the morphing concept can provide sufficient roll authority to allow controllability of the flight. The additional degrees of freedom offered by morphing can be also used to vary the plane lift coefficient, similarly to conventional flaps. The efficiency improvements offered by this technique are evaluated numerically, and compared to the performance of a rigid wing.

  4. Aircraft wing structural detail design (wing, aileron, flaps, and subsystems)

    Science.gov (United States)

    Downs, Robert; Zable, Mike; Hughes, James; Heiser, Terry; Adrian, Kenneth

    1993-01-01

    The goal of this project was to design, in detail, the wing, flaps, and ailerons for a primary flight trainer. Integrated in this design are provisions for the fuel system, the electrical system, and the fuselage/cabin carry-through interface structure. This conceptual design displays the general arrangement of all major components in the wing structure, taking into consideration the requirements set forth by the appropriate sections of Federal Aviation Regulation Part 23 (FAR23) as well as those established in the statement of work.

  5. Transonic Semispan Aerodynamic Testing of the Hybrid Wing Body with Over Wing Nacelles in the National Transonic Facility

    Science.gov (United States)

    Chan, David T.; Hooker, John R.; Wick, Andrew; Plumley, Ryan W.; Zeune, Cale H.; Ol, Michael V.; DeMoss, Joshua A.

    2017-01-01

    A wind tunnel investigation of a 0.04-scale model of the Lockheed Martin Hybrid Wing Body (HWB) with Over Wing Nacelles (OWN) air mobility transport configuration was conducted in the National Transonic Facility at the NASA Langley Research Center under a collaborative partnership between NASA, the Air Force Research Laboratory, and Lockheed Martin Aeronautics Company. The wind tunnel test sought to validate the transonic aerodynamic performance of the HWB and to validate the efficiency benefits of the OWN installation as compared to the traditional under-wing installation. The semispan HWB model was tested in a clean wing configuration and also tested with two different nacelles representative of a modern turbofan engine and a future advanced high bypass ratio engine. The nacelles were installed in three different locations with two over-wing positions and one under-wing position. Five-component force and moment data, surface static pressure data, and aeroelastic deformation data were acquired. For the cruise configuration, the model was tested in an angle-of-attack range between -2 and 10 degrees at free-stream Mach numbers from 0.3 to 0.9 and at unit Reynolds numbers between 8 and 39 million per foot, achieving a maximum of 80% of flight Reynolds numbers across the Mach number range. The test results validated pretest computational fluid dynamic (CFD) simulations of the HWB performance including the OWN benefit and the results also exhibited excellent transonic drag data repeatability to within +/-1 drag count. This paper details the experimental setup and model overview, presents some sample data results, and describes the facility improvements that led to the success of the test.

  6. A computational study of the wing-wing and wing-body interactions of a model insect

    Institute of Scientific and Technical Information of China (English)

    Xin Yu; Mao Sun

    2009-01-01

    The aerodynamic interaction between the contralateral wings and between the body and wings of a model insect are studied, by using the method of numerically solving the Navier-Stokes equations over moving overset grids, under typical hovering and forward flight conditions. Both the interaction between the contralateral wings and the interaction between the body and wings are very weak, e.g. at hovering, changes in aerodynamic forces of a wing due to the present of the other wing are less than 3% and changes in aerodynamic forces of the wings due to presence of thebody are less than 2%. The reason for this is as following. During each down-or up-stroke, a wing produces a vortexring, which induces a relatively large jet-like flow inside the ring but very small flow outside the ring. The vortex tings of the left and right wings are on the two sides of the body. Thus one wing is outside vortex ring of the other wing and the body is outside the vortex rings of the left and right wings, resulting in the weak interactions.

  7. Aerodynamic control with passively pitching wings

    Science.gov (United States)

    Gravish, Nick; Wood, Robert

    Flapping wings may pitch passively under aerodynamic and inertial loads. Such passive pitching is observed in flapping wing insect and robot flight. The effect of passive wing pitch on the control dynamics of flapping wing flight are unexplored. Here we demonstrate in simulation and experiment the critical role wing pitching plays in yaw control of a flapping wing robot. We study yaw torque generation by a flapping wing allowed to passively rotate in the pitch axis through a rotational spring. Yaw torque is generated through alternating fast and slow upstroke and and downstroke. Yaw torque sensitively depends on both the rotational spring force law and spring stiffness, and at a critical spring stiffness a bifurcation in the yaw torque control relationship occurs. Simulation and experiment reveal the dynamics of this bifurcation and demonstrate that anomalous yaw torque from passively pitching wings is the result of aerodynamic and inertial coupling between the pitching and stroke-plane dynamics.

  8. Insect Evolution: The Origin of Wings.

    Science.gov (United States)

    Ross, Andrew

    2017-02-06

    The debate on the evolution of wings in insects has reached a new level. The study of primitive fossil insect nymphs has revealed that wings developed from a combination of the dorsal part of the thorax and the body wall.

  9. Span morphing using the GNATSpar wing

    OpenAIRE

    2016-01-01

    Rigid wings usually fly at sub-optimal conditions generating unnecessary aerodynamic loses represented in flight time, fuel consumption, and unfavourable operational characteristics. High aspect ratio wings have good range and fuel efficiency, but lack manoeuvrability. On the other hand, low aspect ratio wings fly faster and are more manoeuvrable, but have poor aerodynamic performance. Span morphing technology allows integrating both features in a single wing design and allows continuously ad...

  10. Structural Analysis of a Dragonfly Wing

    OpenAIRE

    Jongerius, S.R.; Lentink, D.

    2010-01-01

    Dragonfly wings are highly corrugated, which increases the stiffness and strength of the wing significantly, and results in a lightweight structure with good aerodynamic performance. How insect wings carry aerodynamic and inertial loads, and how the resonant frequency of the flapping wings is tuned for carrying these loads, is however not fully understood. To study this we made a three-dimensional scan of a dragonfly (Sympetrum vulgatum) fore- and hindwing with a micro-CT scanner. The scans c...

  11. Low Aspect-Ratio Wings for Wing-Ships

    DEFF Research Database (Denmark)

    Filippone, Antonino; Selig, M.

    1998-01-01

    Flying on ground poses technical and aerodynamical challenges. The requirements for compactness, efficiency, manouverability, off-design operation,open new areas of investigations in the fieldof aerodynamic analysis and design. A review ofthe characteristics of low-aspect ratio wings, in- and out...

  12. Shape optimisation and performance analysis of flapping wings

    KAUST Repository

    Ghommem, Mehdi

    2012-09-04

    In this paper, shape optimisation of flapping wings in forward flight is considered. This analysis is performed by combining a local gradient-based optimizer with the unsteady vortex lattice method (UVLM). Although the UVLM applies only to incompressible, inviscid flows where the separation lines are known a priori, Persson et al. [1] showed through a detailed comparison between UVLM and higher-fidelity computational fluid dynamics methods for flapping flight that the UVLM schemes produce accurate results for attached flow cases and even remain trend-relevant in the presence of flow separation. As such, they recommended the use of an aerodynamic model based on UVLM to perform preliminary design studies of flapping wing vehicles Unlike standard computational fluid dynamics schemes, this method requires meshing of the wing surface only and not of the whole flow domain [2]. From the design or optimisation perspective taken in our work, it is fairly common (and sometimes entirely necessary, as a result of the excessive computational cost of the highest fidelity tools such as Navier-Stokes solvers) to rely upon such a moderate level of modelling fidelity to traverse the design space in an economical manner. The objective of the work, described in this paper, is to identify a set of optimised shapes that maximise the propulsive efficiency, defined as the ratio of the propulsive power over the aerodynamic power, under lift, thrust, and area constraints. The shape of the wings is modelled using B-splines, a technology used in the computer-aided design (CAD) field for decades. This basis can be used to smoothly discretize wing shapes with few degrees of freedom, referred to as control points. The locations of the control points constitute the design variables. The results suggest that changing the shape yields significant improvement in the performance of the flapping wings. The optimisation pushes the design to "bird-like" shapes with substantial increase in the time

  13. Mass flow and its pulsation measurements in supersonic wing wake

    Science.gov (United States)

    Shmakov, A. S.; Shevchenko, A. M.; Yatskikh, A. A.; Yermolaev, Yu. G.

    2016-10-01

    The results of experimental study of the flow in the wing wake are presented. Experiments were carried out in supersonic wind tunnel T-325 of ITAM SB RAS. Rectangle half-wing with sharp edges with a chord length of 30 mm and semispan of 95 mm was used to generate vortex wake. Experimental data were obtained in the cross section located 6 chord length downstream of the trailing edge at Mach numbers of 2.5 and 4 and at wing angles of attack of 4 and 10 degrees. Constant temperature hot-wire anemometer was used to measure disturbances in supersonic flow. Hot-wire was made of a tungsten wire with a diameter of 10 μm and length of 1.5 mm. Shlieren flow visualization were performed. As a result, the position and size of the vortex core in the wake of a rectangular wing were determined. For the first time experimental data on the mass flow distribution and its pulsations in the supersonic longitudinal vortex were obtained.

  14. Bat flight with bad wings: is flight metabolism affected by damaged wings?

    Science.gov (United States)

    Voigt, Christian C

    2013-04-15

    Infection of North American bats with the keratin-digesting fungus Geomyces destructans often results in holes and ruptures of wing membranes, yet it is unknown whether flight performance and metabolism of bats are altered by such injuries. I conducted flight experiments in a circular flight arena with Myotis albescens and M. nigricans individuals with an intact or ruptured trailing edge of one of the plagiopatagial membranes. In both species, individuals with damaged wings were lighter, had a higher aspect ratio (squared wing span divided by wing area) and an increased wing loading (weight divided by wing area) than conspecifics with intact wings. Bats with an asymmetric reduction of the wing area flew at similar speeds to conspecifics with intact wings but performed fewer flight manoeuvres. Individuals with damaged wings showed lower metabolic rates during flight than conspecifics with intact wings, even when controlling for body mass differences; the difference in mass-specific metabolic rate may be attributable to the lower number of flight manoeuvres (U-turns) by bats with damaged wings compared with conspecifics with intact wings. Possibly, bats compensated for an asymmetric reduction in wing area by lowering their body mass and avoiding flight manoeuvres. In conclusion, it may be that bats suffer from moderate wing damage not directly, by experiencing increased metabolic rate, but indirectly, by a reduced manoeuvrability and foraging success. This could impede a bat's ability to gain sufficient body mass before hibernation.

  15. The Wings for Angels Project

    Science.gov (United States)

    McMillan, Liberty; McMillan, Ellen; Ayers, Ann

    2012-01-01

    How can the spirits of critically ill children be raised? Alexis Weisel (co-president of the Monarch High School National Art Honor Society, 2010-2011) had this question in mind when she initiated and developed the Wings for Angels Project after hearing about the Believe in Tomorrow (BIT) organization through her art teacher, Ellen McMillan. The…

  16. Wings: Women Entrepreneurs Take Flight.

    Science.gov (United States)

    Baldwin, Fred D.

    1997-01-01

    Women's Initiative Networking Groups (WINGS) provides low- and moderate-income women in Appalachian Kentucky with training in business skills, contacts, and other resources they need to succeed as entrepreneurs. The women form informal networks to share business know-how and support for small business startup and operations. The program plans to…

  17. FLEXIBLE WING INDIVIDUAL DROP GLIDER

    Science.gov (United States)

    The feasibility of the paraglider concept as a means of descent for individual airborne troops is presented. Full-scale 22-foot inflatable wings and...in an effort to achieve system reliability. The feasibility of using the paraglider as a means of controlled delivery of airborne paratroopers was successfully demonstrated.

  18. [Winged scapula in lyme borreliosis].

    Science.gov (United States)

    Rausch, V; Königshausen, M; Gessmann, J; Schildhauer, T A; Seybold, D

    2016-06-01

    Here we present the case of a young patient with one-sided winged scapula and lyme borreliosis. This disease can be very delimitating in daily life. If non-operative treatment fails, dynamic or static stabilization of the scapula can be a therapeutic option.

  19. Review Results on Wing-Body Interference

    OpenAIRE

    Frolov Vladimir

    2016-01-01

    The paper presents an overview of results for wing-body interference, obtained by the author for varied wing-body combinations. The lift-curve slopes of the wing-body combinations are considered. In this paper a discrete vortices method (DVM) and 2D potential model for cross-flow around fuselage are used. The circular and elliptical cross-sections of the fuselage and flat wings of various forms are considered. Calculations showed that the value of the lift-curve slopes of the wing-body combin...

  20. Further studies of stall flutter and nonlinear divergence of two-dimensional wings

    Science.gov (United States)

    Dugundji, J.; Chopra, I.

    1975-01-01

    An experimental investigation is made of the purely torsional stall flutter of a two-dimensional wing pivoted about the midchord, and also of the bending-torsion stall flutter of a two-dimensional wing pivoted about the quarterchord. For the purely torsional flutter case, large amplitude limit cycles ranging from + or - 11 to + or - 160 degrees were observed. Nondimensional harmonic coefficients were extracted from the free transient vibration tests for amplitudes up to 80 degrees. Reasonable nondimensional correlation was obtained for several wing configurations. For the bending-torsion flutter case, large amplitude coupled limit cycles were observed with torsional amplitudes as large as + or - 40 degrees. The torsion amplitudes first increased, then decreased with increasing velocity. Additionally, a small amplitude, predominantly torsional flutter was observed when the static equilibrium angle was near the stall angle.

  1. Flight Testing of Novel Compliant Spines for Passive Wing Morphing on Ornithopters

    Science.gov (United States)

    Wissa, Aimy; Guerreiro, Nelson; Grauer, Jared; Altenbuchner, Cornelia; Hubbard, James E., Jr.; Tummala, Yashwanth; Frecker, Mary; Roberts, Richard

    2013-01-01

    Unmanned Aerial Vehicles (UAVs) are proliferating in both the civil and military markets. Flapping wing UAVs, or ornithopters, have the potential to combine the agility and maneuverability of rotary wing aircraft with excellent performance in low Reynolds number flight regimes. The purpose of this paper is to present new free flight experimental results for an ornithopter equipped with one degree of freedom (1DOF) compliant spines that were designed and optimized in terms of mass, maximum von-Mises stress, and desired wing bending deflections. The spines were inserted in an experimental ornithopter wing spar in order to achieve a set of desired kinematics during the up and down strokes of a flapping cycle. The ornithopter was flown at Wright Patterson Air Force Base in the Air Force Research Laboratory Small Unmanned Air Systems (SUAS) indoor flight facility. Vicon motion tracking cameras were used to track the motion of the vehicle for five different wing configurations. The effect of the presence of the compliant spine on wing kinematics and leading edge spar deflection during flight is presented. Results show that the ornithopter with the compliant spine inserted in its wing reduced the body acceleration during the upstroke which translates into overall lift gains.

  2. Review Results on Wing-Body Interference

    Directory of Open Access Journals (Sweden)

    Frolov Vladimir

    2016-01-01

    Full Text Available The paper presents an overview of results for wing-body interference, obtained by the author for varied wing-body combinations. The lift-curve slopes of the wing-body combinations are considered. In this paper a discrete vortices method (DVM and 2D potential model for cross-flow around fuselage are used. The circular and elliptical cross-sections of the fuselage and flat wings of various forms are considered. Calculations showed that the value of the lift-curve slopes of the wing-body combinations may exceed the same value for an isolated wing. This result confirms an experimental data obtained by other authors earlier. Within a framework of the used mathematical models the investigations to optimize the wing-body combination were carried. The present results of the optimization problem for the wing-body combination allowed to select the optimal geometric characteristics for configuration to maximize the values of the lift-curve slopes of the wing-body combination. It was revealed that maximums of the lift-curve slopes for the optimal mid-wing configuration with elliptical cross-section body had a sufficiently large relative width of the body (more than 30% of the span wing.

  3. AST Composite Wing Program: Executive Summary

    Science.gov (United States)

    Karal, Michael

    2001-01-01

    The Boeing Company demonstrated the application of stitched/resin infused (S/RFI) composite materials on commercial transport aircraft primary wing structures under the Advanced Subsonic technology (AST) Composite Wing contract. This report describes a weight trade study utilizing a wing torque box design applicable to a 220-passenger commercial aircraft and was used to verify the weight savings a S/RFI structure would offer compared to an identical aluminum wing box design. This trade study was performed in the AST Composite Wing program, and the overall weight savings are reported. Previous program work involved the design of a S/RFI-base-line wing box structural test component and its associated testing hardware. This detail structural design effort which is known as the "semi-span" in this report, was completed under a previous NASA contract. The full-scale wing design was based on a configuration for a MD-90-40X airplane, and the objective of this structural test component was to demonstrate the maturity of the S/RFI technology through the evaluation of a full-scale wing box/fuselage section structural test. However, scope reductions of the AST Composite Wing Program pre-vented the fabrication and evaluation of this wing box structure. Results obtained from the weight trade study, the full-scale test component design effort, fabrication, design development testing, and full-scale testing of the semi-span wing box are reported.

  4. Topology of Vortex-Wing Interaction

    Science.gov (United States)

    McKenna, Chris; Rockwell, Donald

    2016-11-01

    Aircraft flying together in an echelon or V formation experience aerodynamic advantages. Impingement of the tip vortex from the leader (upstream) wing on the follower wing can yield an increase of lift to drag ratio. This enhancement is known to depend on the location of vortex impingement on the follower wing. Particle image velocimetry is employed to determine streamline topology in successive crossflow planes, which characterize the streamwise evolution of the vortex structure along the chord of the follower wing and into its wake. Different modes of vortex-follower wing interaction are created by varying both the spanwise and vertical locations of the leader wing. These modes are defined by differences in the number and locations of critical points of the flow topology, and involve bifurcation, attenuation, and mutual induction. The bifurcation and attenuation modes decrease the strength of the tip vortex from the follower wing. In contrast, the mutual induction mode increases the strength of the follower tip vortex. AFOSR.

  5. Periodic and Chaotic Flapping of Insectile Wings

    CERN Document Server

    Huang, Yangyang

    2015-01-01

    Insects use flight muscles attached at the base of the wings to produce impressive wing flapping frequencies. The maximum power output of these flight muscles is insufficient to maintain such wing oscillations unless there is good elastic storage of energy in the insect flight system. Here, we explore the intrinsic self-oscillatory behavior of an insectile wing model, consisting of two rigid wings connected at their base by an elastic torsional spring. We study the wings behavior as a function of the total energy and spring stiffness. Three types of behavior are identified: end-over-end rotation, chaotic motion, and periodic flapping. Interestingly, the region of periodic flapping decreases as energy increases but is favored as stiffness increases. These findings are consistent with the fact that insect wings and flight muscles are stiff. They further imply that, by adjusting their muscle stiffness to the desired energy level, insects can maintain periodic flapping mechanically for a range of operating condit...

  6. Piezoelectrically actuated insect scale flapping wing

    Science.gov (United States)

    Mukherjee, Sujoy; Ganguli, Ranjan

    2010-04-01

    An energy method is used in order to derive the non-linear equations of motion of a smart flapping wing. Flapping wing is actuated from the root by a PZT unimorph in the piezofan configuration. Dynamic characteristics of the wing, having the same size as dragonfly Aeshna Multicolor, are analyzed using numerical simulations. It is shown that flapping angle variations of the smart flapping wing are similar to the actual dragonfly wing for a specific feasible voltage. An unsteady aerodynamic model based on modified strip theory is used to obtain the aerodynamic forces. It is found that the smart wing generates sufficient lift to support its own weight and carry a small payload. It is therefore a potential candidate for flapping wing of micro air vehicles.

  7. Computational Analysis of Powered Lift Augmentation for the LEAPTech Distributed Electric Propulsion Wing

    Science.gov (United States)

    Deere, Karen A.; Viken, Sally A.; Carter, Melissa B.; Viken, Jeffrey K.; Wiese, Michael R.; Farr, Norma L.

    2017-01-01

    A computational study of a distributed electric propulsion wing with a 40deg flap deflection has been completed using FUN3D. Two lift-augmentation power conditions were compared with the power-off configuration on the high-lift wing (40deg flap) at a 73 mph freestream flow and for a range of angles of attack from -5 degrees to 14 degrees. The computational study also included investigating the benefit of corotating versus counter-rotating propeller spin direction to powered-lift performance. The results indicate a large benefit in lift coefficient, over the entire range of angle of attack studied, by using corotating propellers that all spin counter to the wingtip vortex. For the landing condition, 73 mph, the unpowered 40deg flap configuration achieved a maximum lift coefficient of 2.3. With high-lift blowing the maximum lift coefficient increased to 5.61. Therefore, the lift augmentation is a factor of 2.4. Taking advantage of the fullspan lift augmentation at similar performance means that a wing powered with the distributed electric propulsion system requires only 42 percent of the wing area of the unpowered wing. This technology will allow wings to be 'cruise optimized', meaning that they will be able to fly closer to maximum lift over drag conditions at the design cruise speed of the aircraft.

  8. 复合材料后掠翼机翼气动弹性分析%Aeroelastic Characteristics Analysis of a Composite Backward-Swept Wing

    Institute of Scientific and Technical Information of China (English)

    周宏霞; 吕锁宁

    2012-01-01

    对于复合材料后掠翼机翼,扭转发散问题一般并不突出,其操纵面的操纵效率和颤振临界动压是比较关心的两个问题。文章采用COMPASS软件,对某复合材料后掠翼飞机进行了操纵效率分析,并重点计算了该机在不同高度下颤振速度随马赫数的变化情况,详细分析了机翼振动、颤振特性随蒙皮不同铺层比变化情况。结果表明,舵面操纵效率随着马赫数的增加而降低,飞机设计要通过设计参数调整选择合适的副翼反效动压与扭转发散动压之比,使飞行范围内的操纵效率尽可能高;同时复合材料后掠机翼的弯扭耦合效应相当突出,而复合材料剪裁可以调整0°、+45°、90°铺层比例,提高结构扭转刚度,从而提高飞机颤振速度。%For a composite material backward-swept wing, the control surface efficiency and flutter speed are more worth concerning compared with torsion divergence. The aeroelastic characteristics were calculated and analyzed by the COMPASS software, including the control efficiency of a wing separately, and various flutter speeds corresponding to different subsonic mach numbers were calculated emphatically. The results indicate that the control surface efficiency decreases as Mach number increases. The design parameters must be adjusted to obtain appropriate aileron reversal dynamics pressure to torsion radiation dynamics pressure ratio which makes the control efficiency higher. At the same time the bending and torsion coupling effect of composite material swept-back wing is quite severe. The composite material clipping can rectify the proportion of the 0°, +45° and 90° in order to enhance the structure torsion stiffness and the aircraft flutter speed.

  9. Effects of wing locations on wing rock induced by forebody vortices

    Directory of Open Access Journals (Sweden)

    Ma Baofeng

    2016-10-01

    Full Text Available Previous studies have shown that asymmetric vortex wakes over slender bodies exhibit a multi-vortex structure with an alternate arrangement along a body axis at high angle of attack. In this investigation, the effects of wing locations along a body axis on wing rock induced by forebody vortices was studied experimentally at a subcritical Reynolds number based on a body diameter. An artificial perturbation was added onto the nose tip to fix the orientations of forebody vortices. Particle image velocimetry was used to identify flow patterns of forebody vortices in static situations, and time histories of wing rock were obtained using a free-to-roll rig. The results show that the wing locations can affect significantly the motion patterns of wing rock owing to the variation of multi-vortex patterns of forebody vortices. As the wing locations make the forebody vortices a two-vortex pattern, the wing body exhibits regularly divergence and fixed-point motion with azimuthal variations of the tip perturbation. If a three-vortex pattern exists over the wing, however, the wing-rock patterns depend on the impact of the highest vortex and newborn vortex. As the three vortices together influence the wing flow, wing-rock patterns exhibit regularly fixed-points and limit-cycled oscillations. With the wing moving backwards, the newborn vortex becomes stronger, and wing-rock patterns become fixed-points, chaotic oscillations, and limit-cycled oscillations. With further backward movement of wings, the vortices are far away from the upper surface of wings, and the motions exhibit divergence, limit-cycled oscillations and fixed-points. For the rearmost location of the wing, the wing body exhibits stochastic oscillations and fixed-points.

  10. A fundamental avian wing-stroke provides a new perspective on the evolution of flight.

    Science.gov (United States)

    Dial, Kenneth P; Jackson, Brandon E; Segre, Paolo

    2008-02-21

    The evolution of avian flight remains one of biology's major controversies, with a long history of functional interpretations of fossil forms given as evidence for either an arboreal or cursorial origin of flight. Despite repeated emphasis on the 'wing-stroke' as a necessary avenue of investigation for addressing the evolution of flight, no empirical data exist on wing-stroke dynamics in an experimental evolutionary context. Here we present the first comparison of wing-stroke kinematics of the primary locomotor modes (descending flight and incline flap-running) that lead to level-flapping flight in juvenile ground birds throughout development. We offer results that are contrary both to popular perception and inferences from other studies. Starting shortly after hatching and continuing through adulthood, ground birds use a wing-stroke confined to a narrow range of less than 20 degrees , when referenced to gravity, that directs aerodynamic forces about 40 degrees above horizontal, permitting a 180 degrees range in the direction of travel. Based on our results, we put forth an ontogenetic-transitional wing hypothesis that posits that the incremental adaptive stages leading to the evolution of avian flight correspond behaviourally and morphologically to transitional stages observed in ontogenetic forms.

  11. Role of wing morphing in thrust generation

    Directory of Open Access Journals (Sweden)

    Mehdi Ghommem

    2014-01-01

    Full Text Available In this paper, we investigate the role of morphing on flight dynamics of two birds by simulating the flow over rigid and morphing wings that have the characteristics of two different birds, namely the Giant Petrel and Dove Prion. The simulation of a flapping rigid wing shows that the root of the wing should be placed at a specific angle of attack in order to generate enough lift to balance the weight of the bird. However, in this case the generated thrust is either very small, or even negative, depending on the wing shape. Further, results show that morphing of the wing enables a significant increase in the thrust and propulsive efficiency. This indicates that the birds actually utilize some sort of active wing twisting and bending to produce enough thrust. This study should facilitate better guidance for the design of flapping air vehicles.

  12. Rotor/Wing Interactions in Hover

    Science.gov (United States)

    Young, Larry A.; Derby, Michael R.

    2002-01-01

    Hover predictions of tiltrotor aircraft are hampered by the lack of accurate and computationally efficient models for rotor/wing interactional aerodynamics. This paper summarizes the development of an approximate, potential flow solution for the rotor-on-rotor and wing-on-rotor interactions. This analysis is based on actuator disk and vortex theory and the method of images. The analysis is applicable for out-of-ground-effect predictions. The analysis is particularly suited for aircraft preliminary design studies. Flow field predictions from this simple analytical model are validated against experimental data from previous studies. The paper concludes with an analytical assessment of the influence of rotor-on-rotor and wing-on-rotor interactions. This assessment examines the effect of rotor-to-wing offset distance, wing sweep, wing span, and flaperon incidence angle on tiltrotor inflow and performance.

  13. Experimental Study on the Wing Formation of a Paraglider Canopy Cell (Inflatable Wing)

    Science.gov (United States)

    Yamamori, Keitaro; Umemura, Akira; Hishida, Manabu

    This study focuses on the formation mechanism of para-foil canopy. Three types of model wing, which represent each cell of para-foil canopy (a rigid wing with air intake, an inflatable wing and a cassette model) were prepared to explore the effects of air intake on inflatable wing formation in wind tunnel experiments. The flow fields both outside and inside of the wings were investigated, together with the process that the flexible wing inflates to form a wing. It was found that the robust nature of canopy is derived from the concaving deformation of the leading edge at small angles of attack, and the enhanced outward suction pressure acting on the leading edge, which are caused by the flexibility of the wing as well as the pressure of air intake in sacrifice of increased drag coefficient.

  14. Experimental Investigation on Limit Cycle Wing Rock Effect on Wing Body Configuration Induced by Forebody Vortices

    National Research Council Canada - National Science Library

    Rong, Zhen; Deng, Xueying; Ma, Baofeng; Wang, Bing

    2016-01-01

    ...° swept wing configuration undergoing a limit cycle oscillation using a synchronous measurement and control technique of wing rock/particle image velocimetry/dynamic pressure associated with the time...

  15. Morphing fixed wing MAV modeling using VAM

    OpenAIRE

    2012-01-01

    The design and implementation of a morphing Micro Air Vehicle (MAV) wing using a smart composite is attempted in this research work. Control surfaces actuated by traditional servos are difficult to instrument and fabricate on thin composite-wings of MAVs. Piezoelectric Fiber Reinforced Composites (PFRCs) are the chosen smart structural materials in the current work for incorporation onto fixed-wing MAVs to simultaneously perform the dual functions of structural load-bearing and actuatio...

  16. Veins improve fracture toughness of insect wings.

    Directory of Open Access Journals (Sweden)

    Jan-Henning Dirks

    Full Text Available During the lifetime of a flying insect, its wings are subjected to mechanical forces and deformations for millions of cycles. Defects in the micrometre thin membranes or veins may reduce the insect's flight performance. How do insects prevent crack related material failure in their wings and what role does the characteristic vein pattern play? Fracture toughness is a parameter, which characterises a material's resistance to crack propagation. Our results show that, compared to other body parts, the hind wing membrane of the migratory locust S. gregaria itself is not exceptionally tough (1.04±0.25 MPa√m. However, the cross veins increase the wing's toughness by 50% by acting as barriers to crack propagation. Using fracture mechanics, we show that the morphological spacing of most wing veins matches the critical crack length of the material (1132 µm. This finding directly demonstrates how the biomechanical properties and the morphology of locust wings are functionally correlated in locusts, providing a mechanically 'optimal' solution with high toughness and low weight. The vein pattern found in insect wings thus might inspire the design of more durable and lightweight artificial 'venous' wings for micro-air-vehicles. Using the vein spacing as indicator, our approach might also provide a basis to estimate the wing properties of endangered or extinct insect species.

  17. Subtractive Structural Modification of Morpho Butterfly Wings.

    Science.gov (United States)

    Shen, Qingchen; He, Jiaqing; Ni, Mengtian; Song, Chengyi; Zhou, Lingye; Hu, Hang; Zhang, Ruoxi; Luo, Zhen; Wang, Ge; Tao, Peng; Deng, Tao; Shang, Wen

    2015-11-11

    Different from studies of butterfly wings through additive modification, this work for the first time studies the property change of butterfly wings through subtractive modification using oxygen plasma etching. The controlled modification of butterfly wings through such subtractive process results in gradual change of the optical properties, and helps the further understanding of structural optimization through natural evolution. The brilliant color of Morpho butterfly wings is originated from the hierarchical nanostructure on the wing scales. Such nanoarchitecture has attracted a lot of research effort, including the study of its optical properties, its potential use in sensing and infrared imaging, and also the use of such structure as template for the fabrication of high-performance photocatalytic materials. The controlled subtractive processes provide a new path to modify such nanoarchitecture and its optical property. Distinct from previous studies on the optical property of the Morpho wing structure, this study provides additional experimental evidence for the origination of the optical property of the natural butterfly wing scales. The study also offers a facile approach to generate new 3D nanostructures using butterfly wings as the templates and may lead to simpler structure models for large-scale man-made structures than those offered by original butterfly wings.

  18. Analysis of bat wings for morphing

    Science.gov (United States)

    Leylek, Emily A.; Manzo, Justin E.; Garcia, Ephrahim

    2008-03-01

    The morphing of wings from three different bat species is studied using an extension of the Weissinger method. To understand how camber affects performance factors such as lift and lift to drag ratio, XFOIL is used to study thin (3% thickness to chord ratio) airfoils at a low Reynolds number of 100,000. The maximum camber of 9% yielded the largest lift coefficient, and a mid-range camber of 7% yielded the largest lift to drag ratio. Correlations between bat wing morphology and flight characteristics are covered, and the three bat wing planforms chosen represent various combinations of morphological components and different flight modes. The wings are studied using the extended Weissinger method in an "unmorphed" configuration using a thin, symmetric airfoil across the span of the wing through angles of attack of 0°-15°. The wings are then run in the Weissinger method at angles of attack of -2° to 12° in a "morphed" configuration modeled after bat wings seen in flight, where the camber of the airfoils comprising the wings is varied along the span and a twist distribution along the span is introduced. The morphed wing configurations increase the lift coefficient over 1000% from the unmorphed configuration and increase the lift to drag ratio over 175%. The results of the three different species correlate well with their flight in nature.

  19. The effects of winglets on low aspect ratio wings at supersonic Mach numbers. M.S. Thesis Report Feb. 1989 - Apr. 1991

    Science.gov (United States)

    Keenan, James A.; Kuhlman, John M.

    1991-01-01

    A computational study was conducted on two wings, of aspect ratios 1.244 and 1.865, each having 65 degree leading edge sweep angles, to determine the effects of nonplanar winglets at supersonic Mach numbers. A Mach number of 1.62 was selected as the design value. The winglets studied were parametrically varied in alignment, length, sweep, camber, thickness, and dihedral angle to determine which geometry had the best predicted performance. For the computational analysis, an available Euler marching technique was used. The results indicated that the possibility existed for wing-winglet geometries to equal the performance of wing-alone bodies in supersonic flows with both bodies having the same semispan. The first wing with winglet used NACA 1402 airfoils for the base wing and was shown to have lift-to-pressure drag ratios within 0.136 percent to 0.360 percent of the NACA 1402 wing-alone. The other base wing was a natural flow wing which was previously designed specifically for a Mach number of 1.62. The results obtained showed that the natural wing-alone had a slightly higher lift-to-pressure drag than the natural wing with winglets.

  20. Latitudinal gradient effect on the wing geometry of Auca coctei (Guérin(Lepidoptera, Nymphalidae

    Directory of Open Access Journals (Sweden)

    María-José Sanzana

    2013-12-01

    Full Text Available Latitudinal gradient effect on the wing geometry of Auca coctei (Guérin (Lepidoptera, Nymphalidae. When the environmental conditions change locally, the organisms and populations may also change in response to the selection pressure, so that the development of individuals may become affected in different degrees. There have been only a few studies in which the patterns of wing morphology variation have been looked into along a latitudinal gradient by means of geometric morphometrics. The aim of this work was to assess the morphologic differentiation of wing among butterfly populations of the species Auca coctei. For this purpose, 9 sampling locations were used which are representative of the distribution range of the butterfly and cover a wide latitudinal range in Chile. The wing morphology was studied in a total of 202 specimens of A. coctei (150 males and 52 females, based on digitization of 17 morphologic landmarks. The results show variation of wing shape in both sexes; however, for the centroid size there was significant variation only in females. Females show smaller centroid size at higher latitudes, therefore in this study the Bergmann reverse rule is confirmed for females of A. coctei. Our study extends morphologic projections with latitude, suggesting that wing variation is an environmental response from diverse origins and may influence different characteristics of the life history of a butterfly.

  1. Projection moire interferometry measurements of micro air vehicle wings

    Science.gov (United States)

    Fleming, Gary A.; Bartram, Scott M.; Waszak, Martin R.; Jenkins, Luther N.

    2001-11-01

    Projection Moire Interferometry (PMI) has been used to measure the structural deformation of micro air vehicle (MAV) wings during a series of wind tunnel tests. The MAV wings had a highly flexible wing structure, generically reminiscent of a bat's wing, which resulted in significant changes in wing shape as a function of MAV angle-of-attack and simulated flight speed. This flow-adaptable wing deformation is thought to provide enhanced vehicle stability and wind gust alleviation compared to rigid wing designs. Investigation of the potential aerodynamic benefits of a flexible MAV wing required measurement of the wing shape under aerodynamic loads. PMI was used to quantify the aerodynamically induced changes in wing shape for three MAV wings having different structural designs and stiffness characteristics. This paper describes the PMI technique, its application to MAV testing, and presents a portion of the PMI data acquired for the three different MAV wings tested.

  2. "Bat Wing Surgical Approach for the Temporomandibular Joint".

    Science.gov (United States)

    Garcia Y Sanchez, J M; Davila Torres, J; Pacheco Rubio, G; Gómez Rodríguez, C L

    2015-09-01

    The temporomandibular joint (TMJ) is anatomically complex; with its close proximity to neurovascular structures, including the facial nerve that gives a high degree of difficulty during surgical exposure. When the first description on TMJ surgery by Orlow in 1913 was published it gave an account describing the basic retroauricular, preauricular, endoaural and submandibular approaches, on treatment of articular pathologies as used today. The proposed study of the 'Bat Wing' approach, first described in 1993 by Garcia y Sanchez J.M. as a surgical alternative, offers great advantages is that it avoids the section of the ear canal and provides a wide surgical field. The management of the proposed technique has wide application with multiple joints addressed, achieving major objectives such as avoiding facial nerve damage, as well as avoiding the section of the external auditory canal with an optimum visibility of the operative field. The Department of Maxillofacial Surgery National Medical Center XXI Century records over a period of approximately 18 months have completed twenty TMJ surgeries using the 'Bat Wing', approach. The bat wing approach is a surgical alternative that offers broad exposure of the surgical field in TMJ, it is effective and meets the goal of exposing the area to intervene safely, good visibility and access to the site to intervene. It perfectly fulfills the above described.

  3. Aerostructural optimization of a morphing wing for airborne wind energy applications

    Science.gov (United States)

    Fasel, U.; Keidel, D.; Molinari, G.; Ermanni, P.

    2017-09-01

    Airborne wind energy (AWE) vehicles maximize energy production by constantly operating at extreme wing loading, permitted by high flight speeds. Additionally, the wide range of wind speeds and the presence of flow inhomogeneities and gusts create a complex and demanding flight environment for AWE systems. Adaptation to different flow conditions is normally achieved by conventional wing control surfaces and, in case of ground generator-based systems, by varying the reel-out speed. These control degrees of freedom enable to remain within the operational envelope, but cause significant penalties in terms of energy output. A significantly greater adaptability is offered by shape-morphing wings, which have the potential to achieve optimal performance at different flight conditions by tailoring their airfoil shape and lift distribution at different levels along the wingspan. Hence, the application of compliant structures for AWE wings is very promising. Furthermore, active gust load alleviation can be achieved through morphing, which leads to a lower weight and an expanded flight envelope, thus increasing the power production of the AWE system. This work presents a procedure to concurrently optimize the aerodynamic shape, compliant structure, and composite layup of a morphing wing for AWE applications. The morphing concept is based on distributed compliance ribs, actuated by electromechanical linear actuators, guiding the deformation of the flexible—yet load-carrying—composite skin. The goal of the aerostructural optimization is formulated as a high-level requirement, namely to maximize the average annual power production per wing area of an AWE system by tailoring the shape of the wing, and to extend the flight envelope of the wing by actively alleviating gust loads. The results of the concurrent multidisciplinary optimization show a 50.7% increase of extracted power with respect to a sequentially optimized design, highlighting the benefits of morphing and the

  4. Energy Based Topology Optimization of Morphing Wings a Multidisciplinary Global/Local Design Approach

    Science.gov (United States)

    2006-12-01

    the proposed warping wing concept can be effectively used as a morphing winglet for military transport vehicles and has strong potential for use in...counteracting the actuation forces, are taken into account. The mathematical tool is based on a six degree-of-freedom beam model with arbitrary composite

  5. A study on forces acting on a flapping wing

    OpenAIRE

    Cetiner O.; Fenercioglu I.; Vuruskan A.

    2013-01-01

    In order to study the forces acting on a flapping wing, an experimental investigation is performed in steady water flow. In this study, a SD7003 airfoil undergoes combined pitching and plunging motion which simulates the forward flight of small birds. The frequency of pitching motion is equal to the frequency of plunging motion and pitch leads the plunge by a phase angle of 90 degrees. The experiments are conducted at Reynolds numbers of 2500 ≤ Re ≤ 13700 and the vortex formation is recorded ...

  6. Age determination of blue-winged teal

    Science.gov (United States)

    Dane, C.W.

    1968-01-01

    Primary feather length, markings on the greater secondary coverts, and the degree of bill spotting were evaluated as characters for use in the spring to distinguish first-year, blue-winged teal (Anas discors) females from older ones. The length of the 10th primary feather did not prove suitable to separate different aged females. Extreme primary lengths might be used to determine the age of some males. In females that have been through a postnuptial molt the greater secondary coverts have a more symmetrical, and more acutely angled, white, inverted 'V'-marking. Any female with a 'V' subjectively classified as good has gone through at least one postnuptial molt, and a female with no sign of a 'V' on the coverts is a juvenile or yearling before her first postnuptial molt. By measuring the longest bill spot on the upper mandible of each known-age female, it was possible to determine the age of some female teal. Because the spots fade during the breeding season, no lower size limit could be set to delineate first-year females at that time of year, but any nest-trapped hen with a spot longer than 10 mm was considered to be older than 1 year. Upper and lower limits were also established to distinguish some yearlings and 2-year-olds in the fall.

  7. The Realization and Study of Optical Wings

    Science.gov (United States)

    Artusio-Glimpse, Alexandra Brae

    Consider the airfoil: a carefully designed structure capable of stable lift in a uniform air flow. It so happens that air pressure and radiation (light) pressure are similar phenomena because each transfer momentum to flow-disturbing objects. This, then, begs the question: does an optical analogue to the airfoil exist? Though an exceedingly small effect, scientists harness radiation pressure in a wide gamut of applications from micromanipulation of single biological particles to the propulsion of large spacecrafts called solar sails. We introduce a cambered, refractive rod that is subjected to optical forces analogous to those seen in aerodynamics, and I call this analogue the optical wing. Flight characteristics of optical wings are determined by wing shape and material in a uniform radiation field. Theory predicts the lift force and axial torque are functions of the wing's angle of attack with stable and unstable orientations. These structures can operate as intensity-dependent, parametrically driven oscillators. In two-dimensions, the wings exhibit bistability when analyzed in an accelerating frame. In three-dimensions, the motion of axially symmetric spinning hemispherical wings is analogous to a spinning top. Experiments on semi-buoyant wings in water found semicylindrically shaped, refractive microparticles traversed a laser beam and rotated to an illumination-dependent stable orientation. Preliminary tests aid in the development of a calibrated force measurement experiment to directly evaluate the optical forces and torque on these samples. A foundational study of the optical wing, this work contributes to future advancements of flight-by-light.

  8. Biaxial mechanical characterization of bat wing skin.

    Science.gov (United States)

    Skulborstad, A J; Swartz, S M; Goulbourne, N C

    2015-04-21

    The highly flexible and stretchable wing skin of bats, together with the skeletal structure and musculature, enables large changes in wing shape during flight. Such compliance distinguishes bat wings from those of all other flying animals. Although several studies have investigated the aerodynamics and kinematics of bats, few have examined the complex histology and mechanical response of the wing skin. This work presents the first biaxial characterization of the local deformation, mechanical properties, and fiber kinematics of bat wing skin. Analysis of these data has provided insight into the relationships among the structural morphology, mechanical properties, and functionality of wing skin. Large spatial variations in tissue deformation and non-negligible fiber strains in the cross-fiber direction for both chordwise and spanwise fibers indicate fibers should be modeled as two-dimensional elements. The macroscopic constitutive behavior was anisotropic and nonlinear, with very low spanwise and chordwise stiffness (hundreds of kilopascals) in the toe region of the stress-strain curve. The structural arrangement of the fibers and matrix facilitates a low energy mechanism for wing deployment and extension, and we fabricate examples of skins capturing this mechanism. We propose a comprehensive deformation map for the entire loading regime. The results of this work underscore the importance of biaxial field approaches for soft heterogeneous tissue, and provide a foundation for development of bio-inspired skins to probe the effects of the wing skin properties on aerodynamic performance.

  9. Winglets on low aspect ratio wings

    Science.gov (United States)

    Kuhlman, John M.; Liaw, Paul

    1987-01-01

    The drag reduction potentially available from the use of winglets at the tips of low aspect ratio (1.75-2.67) wings with pronounced (45-60 deg) leading edge sweep is assessed numerically for the case of a cruise design point at Mach of 0.8 and a lift coefficient of 0.3. Both wing-winglet and wing-alone design geometries are derived from a linear-theory, minimum induced drag design methodology. Relative performance is evaluated with a nonlinear extended small disturbance potential flow analysis code. Predicted lift coefficient/pressure drag coefficient increases at equal lift for the wing-winglet configurations over the wing-alone planform are of the order of 14.6-15.8, when boundary layer interaction is included.

  10. RNAi screening of developmental toolkit genes: a search for novel wing genes in the red flour beetle, Tribolium castaneum.

    Science.gov (United States)

    Linz, David M; Tomoyasu, Yoshinori

    2015-01-01

    The amazing array of diversity among insect wings offers a powerful opportunity to study the mechanisms guiding morphological evolution. Studies in Drosophila (the fruit fly) have identified dozens of genes important for wing development. These genes are often called candidate genes, serving as an ideal starting point to study wing development in other insects. However, we also need to explore beyond the candidate genes to gain a more comprehensive view of insect wing evolution. As a first step away from the traditional candidate genes, we utilized Tribolium (the red flour beetle) as a model and assessed the potential involvement of a group of developmental toolkit genes (embryonic patterning genes) in beetle wing development. We hypothesized that the highly pleiotropic nature of these developmental genes would increase the likelihood of finding novel wing genes in Tribolium. Through the RNA interference screening, we found that Tc-cactus has a less characterized (but potentially evolutionarily conserved) role in wing development. We also found that the odd-skipped family genes are essential for the formation of the thoracic pleural plates, including the recently discovered wing serial homologs in Tribolium. In addition, we obtained several novel insights into the function of these developmental genes, such as the involvement of mille-pattes and Tc-odd-paired in metamorphosis. Despite these findings, no gene we examined was found to have novel wing-related roles unique in Tribolium. These results suggest a relatively conserved nature of developmental toolkit genes and highlight the limited degree to which these genes are co-opted during insect wing evolution.

  11. The External Degree.

    Science.gov (United States)

    Houle, Cyril O.

    This book examines the external degree in relation to the extremes of attitudes, myths, and data. Emphasis is placed on the emergence of the American external degree, foreign external-degree programs, the purpose of the external degree, the current scene, institutional issues, and problems of general policy. (MJM)

  12. Habitat variation and wing coloration affect wing shape evolution in dragonflies.

    Science.gov (United States)

    Outomuro, D; Dijkstra, K-D B; Johansson, F

    2013-09-01

    Habitats are spatially and temporally variable, and organisms must be able to track these changes. One potential mechanism for this is dispersal by flight. Therefore, we would expect flying animals to show adaptations in wing shape related to habitat variation. In this work, we explored variation in wing shape in relation to preferred water body (flowing water or standing water with tolerance for temporary conditions) and landscape (forested to open) using 32 species of dragonflies of the genus Trithemis (80% of the known species). We included a potential source of variation linked to sexual selection: the extent of wing coloration on hindwings. We used geometric morphometric methods for studying wing shape. We also explored the phenotypic correlation of wing shape between the sexes. We found that wing shape showed a phylogenetic structure and therefore also ran phylogenetic independent contrasts. After correcting for the phylogenetic effects, we found (i) no significant effect of water body on wing shape; (ii) male forewings and female hindwings differed with regard to landscape, being progressively broader from forested to open habitats; (iii) hindwings showed a wider base in wings with more coloration, especially in males; and (iv) evidence for phenotypic correlation of wing shape between the sexes across species. Hence, our results suggest that natural and sexual selection are acting partially independently on fore- and hindwings and with differences between the sexes, despite evidence for phenotypic correlation of wing shape between males and females.

  13. Design, fabrication, and characterization of multifunctional wings to harvest solar energy in flapping wing air vehicles

    Science.gov (United States)

    Perez-Rosado, Ariel; Gehlhar, Rachel D.; Nolen, Savannah; Gupta, Satyandra K.; Bruck, Hugh A.

    2015-06-01

    Currently, flapping wing unmanned aerial vehicles (a.k.a., ornithopters or robotic birds) sustain very short duration flight due to limited on-board energy storage capacity. Therefore, energy harvesting elements, such as flexible solar cells, need to be used as materials in critical components, such as wing structures, to increase operational performance. In this paper, we describe a layered fabrication method that was developed for realizing multifunctional composite wings for a unique robotic bird we developed, known as Robo Raven, by creating compliant wing structure from flexible solar cells. The deformed wing shape and aerodynamic lift/thrust loads were characterized throughout the flapping cycle to understand wing mechanics. A multifunctional performance analysis was developed to understand how integration of solar cells into the wings influences flight performance under two different operating conditions: (1) directly powering wings to increase operation time, and (2) recharging batteries to eliminate need for external charging sources. The experimental data is then used in the analysis to identify a performance index for assessing benefits of multifunctional compliant wing structures. The resulting platform, Robo Raven III, was the first demonstration of a robotic bird that flew using energy harvested from solar cells. We developed three different versions of the wing design to validate the multifunctional performance analysis. It was also determined that residual thrust correlated to shear deformation of the wing induced by torsional twist, while biaxial strain related to change in aerodynamic shape correlated to lift. It was also found that shear deformation of the solar cells induced changes in power output directly correlating to thrust generation associated with torsional deformation. Thus, it was determined that multifunctional solar cell wings may be capable of three functions: (1) lightweight and flexible structure to generate aerodynamic forces, (2

  14. In the wings of physics

    CERN Document Server

    Jacob, Maurice René Michel

    1995-01-01

    In physics research, many activities occur backstage or to continue the theatrical metaphor, in the wings of physics. This book focuses on two such activities: the editing of physics journals and the operation of physical societies. The author was editor of Physics Letters B for particle physics and then of Physics Reports for a total of 18 years, as well as being president of the French Physical Society and later of the European Physical Society. This book puts together papers dealing with such activities which he has written at various times in his career. It takes the reader into the inner circles of scientific editing and of physical societies. Each introduced by a foreword, these papers can be read separately.

  15. Static aeroelastic analysis for generic configuration wing

    Science.gov (United States)

    Lee, IN; Miura, Hirokazu; Chargin, Mladen K.

    1991-01-01

    A static aeroelastic analysis capability that calculates flexible air loads for generic configuration wings was developed. It was made possible by integrating a finite element structural analysis code (MSC/NASTRAN) and a panel code of aerodynamic analysis based on linear potential flow theory. The framework already built in MSC/NASTRAN was used, and the aerodynamic influence coefficient matrix was computed externally and inserted in the NASTRAN by means of a DMAP program. It was shown that deformation and flexible air loads of an oblique wing configuration including asymmetric wings can be calculated reliably by this code both in subsonic and supersonic speeds.

  16. CineVersum BlackWing Four

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    从BlackWing One到现在最新推出的BlackWing Four,一直以来C1ndVersum所带来的投影机都受到了不少投影机爱好者的关注,其帅气的外形搭配独特的欧美系画面风格,让人印象深刻。BlackWingFour是Cine Versum最为强悍的家庭影院投影机之一,

  17. Generic Wing-Body Aerodynamics Data Base

    Science.gov (United States)

    Holst, Terry L.; Olsen, Thomas H.; Kwak, Dochan (Technical Monitor)

    2001-01-01

    The wing-body aerodynamics data base consists of a series of CFD (Computational Fluid Dynamics) simulations about a generic wing body configuration consisting of a ogive-circular-cylinder fuselage and a simple symmetric wing mid-mounted on the fuselage. Solutions have been obtained for Nonlinear Potential (P), Euler (E) and Navier-Stokes (N) solvers over a range of subsonic and transonic Mach numbers and angles of attack. In addition, each solution has been computed on a series of grids, coarse, medium and fine to permit an assessment of grid refinement errors.

  18. Measurement on Camber Deformation of Wings of Free-flying Dragonflies and Beating-flying Dragonflies

    Institute of Scientific and Technical Information of China (English)

    Deqiang Song; Lijiang Zeng

    2004-01-01

    The knowledge of wing orientation and deformation during flapping flight is necessary for a complete aerodynamic analysis, but to date those kinematic features have not been simultaneously quantified for free-flying insects. A projected comb-fringe (PCF) method has been developed for measuring spanwise camber changes on free-flying dragonflies and on beating-flying dragonflies through the course of a wingbeat, which bases on projecting a fringe pattern over the whole measurement area and then measuring the wing deformation from the distorted fringe pattern. Experimental results demonstrate substantial camber changes both along the wingspan and through the course of a wingbeat. The ratio of camber deformation to chord length for hind wing is up to 0.11 at 75% spanwise with a flapping angle of -0.66 degree for a free-flying dragonfly.

  19. Ultrastructure of dragonfly wing veins: composite structure of fibrous material supplemented by resilin.

    Science.gov (United States)

    Appel, Esther; Heepe, Lars; Lin, Chung-Ping; Gorb, Stanislav N

    2015-10-01

    Dragonflies count among the most skilful of the flying insects. Their exceptional aerodynamic performance has been the subject of various studies. Morphological and kinematic investigations have showed that dragonfly wings, though being rather stiff, are able to undergo passive deformation during flight, thereby improving the aerodynamic performance. Resilin, a rubber-like protein, has been suggested to be a key component in insect wing flexibility and deformation in response to aerodynamic loads, and has been reported in various arthropod locomotor systems. It has already been found in wing vein joints, connecting longitudinal veins to cross veins, and was shown to endow the dragonfly wing with chordwise flexibility, thereby most likely influencing the dragonfly's flight performance. The present study revealed that resilin is not only present in wing vein joints, but also in the internal cuticle layers of veins in wings of Sympetrum vulgatum (SV) and Matrona basilaris basilaris (MBB). Combined with other structural features of wing veins, such as number and thickness of cuticle layers, material composition, and cross-sectional shape, resilin most probably has an effect on the vein's material properties and the degree of elastic deformations. In order to elucidate the wing vein ultrastructure and the exact localisation of resilin in the internal layers of the vein cuticle, the approaches of bright-field light microscopy, wide-field fluorescence microscopy, confocal laser-scanning microscopy, scanning electron microscopy and transmission electron microscopy were combined. Wing veins were shown to consist of up to six different cuticle layers and a single row of underlying epidermal cells. In wing veins of MBB, the latter are densely packed with light-scattering spheres, previously shown to produce structural colours in the form of quasiordered arrays. Longitudinal and cross veins differ significantly in relative thickness of exo- and endocuticle, with cross veins

  20. Active Dihedral Control System for a Torisionally Flexible Wing

    Science.gov (United States)

    Kendall, Greg T. (Inventor); Lisoski, Derek L. (Inventor); Morgan, Walter R. (Inventor); Griecci, John A. (Inventor)

    2015-01-01

    A span-loaded, highly flexible flying wing, having horizontal control surfaces mounted aft of the wing on extended beams to form local pitch-control devices. Each of five spanwise wing segments of the wing has one or more motors and photovoltaic arrays, and produces its own lift independent of the other wing segments, to minimize inter-segment loads. Wing dihedral is controlled by separately controlling the local pitch-control devices consisting of a control surface on a boom, such that inboard and outboard wing segment pitch changes relative to each other, and thus relative inboard and outboard lift is varied.

  1. AFM Study of Structure Influence on Butterfly Wings Coloration

    Directory of Open Access Journals (Sweden)

    Dinara Sultanovna Dallaeva

    2012-01-01

    Full Text Available This study describes the structural coloration of the butterfly Vanessa Atalanta wings and shows how the atomic force microscopy (AFM can be applied to the study of wings morphology and wings surface behavior under the temperature. The role of the wings morphology in colors was investigated. Different colors of wings have different topology and can be identified by them. AFM in semi-contact mode was used to study the wings surface. The wing surface area, which is close to the butterfly body, has shiny brown color and the peak of surface roughness is about 600 nm. The changing of morphology at different temperatures is shown.

  2. Kinematics and wing shape across flight speed in the bat, Leptonycteris yerbabuenae

    Science.gov (United States)

    Von Busse, Rhea; Hedenström, Anders; Winter, York; Johansson, L. Christoffer

    2012-01-01

    Summary The morphology and kinematics of a flying animal determines the resulting aerodynamic lift through the regulation of the speed of the air moving across the wing, the wing area and the lift coefficient. We studied the detailed three-dimensional wingbeat kinematics of the bat, Leptonycteris yerbabuenae, flying in a wind tunnel over a range of flight speeds (0–7 m/s), to determine how factors affecting the lift production vary across flight speed and within wingbeats. We found that the wing area, the angle of attack and the camber, which are determinants of the lift production, decreased with increasing speed. The camber is controlled by multiple mechanisms along the span, including the deflection of the leg relative to the body, the bending of the fifth digit, the deflection of the leading edge flap and the upward bending of the wing tip. All these measures vary throughout the wing beat suggesting active or aeroelastic control. The downstroke Strouhal number, Std, is kept relatively constant, suggesting that favorable flow characteristics are maintained during the downstroke, across the range of speeds studied. The Std is kept constant through changes in the stroke plane, from a strongly inclined stroke plane at low speeds to a more vertical stroke plane at high speeds. The mean angular velocity of the wing correlates with the aerodynamic performance and shows a minimum at the speed of maximum lift to drag ratio, suggesting a simple way to determine the optimal speed from kinematics alone. Taken together our results show the high degree of adjustments that the bats employ to fine tune the aerodynamics of the wings and the correlation between kinematics and aerodynamic performance. PMID:23259057

  3. Kinematics and wing shape across flight speed in the bat, Leptonycteris yerbabuenae

    Directory of Open Access Journals (Sweden)

    Rhea Von Busse

    2012-10-01

    The morphology and kinematics of a flying animal determines the resulting aerodynamic lift through the regulation of the speed of the air moving across the wing, the wing area and the lift coefficient. We studied the detailed three-dimensional wingbeat kinematics of the bat, Leptonycteris yerbabuenae, flying in a wind tunnel over a range of flight speeds (0–7 m/s, to determine how factors affecting the lift production vary across flight speed and within wingbeats. We found that the wing area, the angle of attack and the camber, which are determinants of the lift production, decreased with increasing speed. The camber is controlled by multiple mechanisms along the span, including the deflection of the leg relative to the body, the bending of the fifth digit, the deflection of the leading edge flap and the upward bending of the wing tip. All these measures vary throughout the wing beat suggesting active or aeroelastic control. The downstroke Strouhal number, Std, is kept relatively constant, suggesting that favorable flow characteristics are maintained during the downstroke, across the range of speeds studied. The Std is kept constant through changes in the stroke plane, from a strongly inclined stroke plane at low speeds to a more vertical stroke plane at high speeds. The mean angular velocity of the wing correlates with the aerodynamic performance and shows a minimum at the speed of maximum lift to drag ratio, suggesting a simple way to determine the optimal speed from kinematics alone. Taken together our results show the high degree of adjustments that the bats employ to fine tune the aerodynamics of the wings and the correlation between kinematics and aerodynamic performance.

  4. Kinematics and wing shape across flight speed in the bat, Leptonycteris yerbabuenae.

    Science.gov (United States)

    Von Busse, Rhea; Hedenström, Anders; Winter, York; Johansson, L Christoffer

    2012-12-15

    The morphology and kinematics of a flying animal determines the resulting aerodynamic lift through the regulation of the speed of the air moving across the wing, the wing area and the lift coefficient. We studied the detailed three-dimensional wingbeat kinematics of the bat, Leptonycteris yerbabuenae, flying in a wind tunnel over a range of flight speeds (0-7 m/s), to determine how factors affecting the lift production vary across flight speed and within wingbeats. We found that the wing area, the angle of attack and the camber, which are determinants of the lift production, decreased with increasing speed. The camber is controlled by multiple mechanisms along the span, including the deflection of the leg relative to the body, the bending of the fifth digit, the deflection of the leading edge flap and the upward bending of the wing tip. All these measures vary throughout the wing beat suggesting active or aeroelastic control. The downstroke Strouhal number, St(d), is kept relatively constant, suggesting that favorable flow characteristics are maintained during the downstroke, across the range of speeds studied. The St(d) is kept constant through changes in the stroke plane, from a strongly inclined stroke plane at low speeds to a more vertical stroke plane at high speeds. The mean angular velocity of the wing correlates with the aerodynamic performance and shows a minimum at the speed of maximum lift to drag ratio, suggesting a simple way to determine the optimal speed from kinematics alone. Taken together our results show the high degree of adjustments that the bats employ to fine tune the aerodynamics of the wings and the correlation between kinematics and aerodynamic performance.

  5. Replication of butterfly wing and natural lotus leaf structures by nanoimprint on silica sol-gel films.

    Science.gov (United States)

    Saison, Tamar; Peroz, Christophe; Chauveau, Vanessa; Berthier, Serge; Sondergard, Elin; Arribart, Hervé

    2008-12-01

    An original and low cost method for the fabrication of patterned surfaces bioinspired from butterfly wings and lotus leaves is presented. Silica-based sol-gel films are thermally imprinted from elastomeric molds to produce stable structures with superhydrophobicity values as high as 160 degrees water contact angle. The biomimetic surfaces are demonstrated to be tuned from superhydrophobic to superhydrophilic by annealing between 200 degrees C and 500 degrees C.

  6. DrawWing, a program for numerical description of insect wings

    Directory of Open Access Journals (Sweden)

    Adam Tofilski

    2004-05-01

    Full Text Available There is usually a pattern of veins on an insect wing. This pattern is species-specific and is used taxonomically. For example, the coordinates of some characteristic points on the wing are used to compare vein patterns. The characteristic points are often vein junctions or vein ends. A tool is presented that enables automatic identification of vein junctions. An image of an insect wing is used to determine the wing outline and veins. The vein skeleton is obtained using a thinning algorithm. Bezier splines are fitted to both the wing outline and the vein skeleton. The splines are saved in an encapsulated postscript file. Another output file in text format contains the coordinates of vein junctions. Both the program and its source code are available under GNU General Public License at [www.cyf-kr.edu.pl/~rotofils/drawwing.html]. The program presented in this paper automatically provides a numerical description of an insect wing. It converts an image of an insect wing to a list of coordinates of vein junctions, and a wing diagram that can be used as an illustration. Coordinates of the vein junctions extracted by the program from wing images were used successfully to discriminate between males of Dolichovespula sylvestris and Dolichovespula saxonica.

  7. Fruit fly scale robots can hover longer with flapping wings than with spinning wings.

    Science.gov (United States)

    Hawkes, Elliot W; Lentink, David

    2016-10-01

    Hovering flies generate exceptionally high lift, because their wings generate a stable leading edge vortex. Micro flying robots with a similar wing design can generate similar high lift by either flapping or spinning their wings. While it requires less power to spin a wing, the overall efficiency depends also on the actuator system driving the wing. Here, we present the first holistic analysis to calculate how long a fly-inspired micro robot can hover with flapping versus spinning wings across scales. We integrate aerodynamic data with data-driven scaling laws for actuator, electronics and mechanism performance from fruit fly to hummingbird scales. Our analysis finds that spinning wings driven by rotary actuators are superior for robots with wingspans similar to hummingbirds, yet flapping wings driven by oscillatory actuators are superior at fruit fly scale. This crossover is driven by the reduction in performance of rotary compared with oscillatory actuators at smaller scale. Our calculations emphasize that a systems-level analysis is essential for trading-off flapping versus spinning wings for micro flying robots.

  8. Parametric weight evaluation of joined wings by structural optimization

    Science.gov (United States)

    Miura, Hirokazu; Shyu, Albert T.; Wolkovitch, Julian

    1988-01-01

    Joined-wing aircraft employ tandem wings having positive and negative sweep and dihedral, arranged to form diamond shapes in both plan and front views. An optimization method was applied to study the effects of joined-wing geometry parameters on structural weight. The lightest wings were obtained by increasing dihedral and taper ratio, decreasing sweep and span, increasing fraction of airfoil chord occupied by structural box, and locating the joint inboard of the front wing tip.

  9. Coriolis effects enhance lift on revolving wings.

    Science.gov (United States)

    Jardin, T; David, L

    2015-03-01

    At high angles of attack, an aircraft wing stalls. This dreaded event is characterized by the development of a leading edge vortex on the upper surface of the wing, followed by its shedding which causes a drastic drop in the aerodynamic lift. At similar angles of attack, the leading edge vortex on an insect wing or an autorotating seed membrane remains robustly attached, ensuring high sustained lift. What are the mechanisms responsible for both leading edge vortex attachment and high lift generation on revolving wings? We review the three main hypotheses that attempt to explain this specificity and, using direct numerical simulations of the Navier-Stokes equations, we show that the latter originates in Coriolis effects.

  10. Left-Wing Extremism: The Current Threat

    Energy Technology Data Exchange (ETDEWEB)

    Karl A. Seger

    2001-04-30

    Left-wing extremism is ''alive and well'' both in the US and internationally. Although the current domestic terrorist threat within the U. S. is focused on right-wing extremists, left-wing extremists are also active and have several objectives. Leftist extremists also pose an espionage threat to U.S. interests. While the threat to the U.S. government from leftist extremists has decreased in the past decade, it has not disappeared. There are individuals and organizations within the U.S. who maintain the same ideology that resulted in the growth of left-wing terrorism in this country in the 1970s and 1980s. Some of the leaders from that era are still communicating from Cuba with their followers in the U.S., and new leaders and groups are emerging.

  11. Mallard age and sex determination from wings

    Science.gov (United States)

    Carney, S.M.; Geis, A.D.

    1960-01-01

    This paper describes characters on the wing plumage of the mallard that indicate age and sex. A key outlines a logical order in which to check age and sex characters on wings. This method was tested and found to be more than 95 percent reliable, although it was found that considerable practice and training with known-age specimens was required to achieve this level of accuracy....The implications of this technique and the sampling procedure it permits are discussed. Wing collections could provide information on production, and, if coupled with a banding program could permit seasonal population estimates to be calculated. In addition, representative samples of wings would provide data to check the reliability of several other waterfowl surveys.

  12. Trajectory Optimization Design for Morphing Wing Missile

    Institute of Scientific and Technical Information of China (English)

    Ruisheng Sun; Chao Ming; Chuanjie Sun

    2015-01-01

    This paper presents a new particle swarm optimization ( PSO) algorithm to optimize the trajectory of morphing⁃wing missile so as to achieve the enlargement of the maximum range. Equations of motion for the two⁃dimensional dynamics are derived by treating the missile as an ideal controllable mass point. An investigation of aerodynamic characteristics of morphing⁃wing missile with varying geometries is performed. After deducing the optimizing trajectory model for maximizing range, a type of discrete method is put forward for taking optimization control problem into nonlinear dynamic programming problem. The optimal trajectory is solved by using PSO algorithm and penalty function method. The simulation results suggest that morphing⁃wing missile has the larger range than the fixed⁃shape missile when launched at supersonic speed, while morphing⁃wing missile has no obvious range increment than the fixed⁃shape missile at subsonic speed.

  13. Molecular determinants of bat wing development.

    Science.gov (United States)

    Sears, K E

    2008-01-01

    The specialization of the forelimb into a wing allowed bats to become the only mammals to achieve powered flight. Recent studies in developmental biology have begun to elucidate the molecular mechanisms behind elements of this important morphological transformation. Specifically, researchers have identified molecular changes contributing to: the formation of the bat wing membrane, the elongation of skeletal elements of the bat wing and the reduction of the bat ulna. The general picture emerging from this research is that small changes in the expression of genes critical to many aspects of development have driven large changes in bat wing morphology. Thus, bats can be added to the growing list of groups in which expression changes in key developmental genes have been linked to the evolution of morphological innovations (e.g. early bilaterians, cetaceans, insects).

  14. Analysis of the Wing Tsun Punching Methods

    Directory of Open Access Journals (Sweden)

    Jeff Webb

    2012-07-01

    Full Text Available The three punching techniques of Wing Tsun, while few in number, represent an effective approach to striking with the closed fist. At first glance, the rather short stroke of each punch would seem disproportionate to the amount of power it generates. Therefore, this article will discuss the structure and body mechanics of each punch, in addition to the various training methods employed for developing power. Two of the Wing Tsun punches, namely the lifting punch and the hooking punch, are often confused with similar punches found in Western boxing. The key differences between the Wing Tsun and boxing punches, both in form and function, will be discussed. Finally, the strategy for applying the Wing Tsun punches will serve as the greatest factor in differentiating them from the punches of other martial arts styles.

  15. Aerodynamic study on wing and tail small UAV without runways

    Science.gov (United States)

    Soetanto, Maria F.; R., Randy; Alfan M., R.; Dzaldi

    2016-06-01

    This paper consists of the design and analysis of the aerodynamics of the profiles of wing and tail of a Small Unmanned Aerial Vehicle (UAV). UAV is a remote-controlled aircraft that can carry cameras, sensors and even weapons on an area that needed aerial photography or aerial video [1]. The aim of this small UAV is for used in situations where manned flight is considered too risky or difficult, such as fire fighting or surveillance, while the term 'small means the design of this UAV has to be relatively small and portable so that peoples are able to carry it during their operations [CASR Part 101.240: it is a UAV which is has a launch mass greater than 100 grams but less than 100 kilograms] [2]. Computational Fluid Dynamic (CFD) method was used to analyze the fluid flow characteristics around the aerofoil's profiles, such as the lift generation for each angle of attack and longitudinal stability caused by vortex generation on trailing edge. Based on the analysis and calculation process, Clark-Y MOD with aspect ratio, AR = 4.28 and taper ratio, λ = 0.65 was chosen as the wing aerofoil and SD 8020 with AR = 4.8 and λ = 0.5 was chosen as the horizontal tail, while SD 8020 with AR = 1.58 and λ = 0.5 was chosen as the vertical tail. The lift and drag forces generated for wing and tail surfaces can be determined from the Fluent 6.3 simulation. Results showed that until angle of attack of 6 degrees, the formation of flow separation is still going on behind the trailing edge, and the stall condition occurs at 14 degrees angle of attack which is characterized by the occurrence of flow separation at leading edge, with a maximum lift coefficient (Cl) obtained = 1.56. The results of flight tests show that this small UAV has successfully maneuvered to fly, such as take off, some acrobatics when cruising and landing smoothly, which means that the calculation and analysis of aerodynamic aerofoil's profile used on the wing and tail of the Small UAV were able to be validated.

  16. Cross Service Fixed-Wing Cost Estimation

    Science.gov (United States)

    2016-05-17

    clarify the costing methods for O&S costs for fixed-wing delivery platforms with the intent of extending the research to other cross- service mission costs...proof-of-concept, this project will concentrate on equating equitable cross- service costs for fixed-wing munitions delivery platforms. The method of... delivery is an essential part of the AoA, especially when the project proposed is the replacement of current missile systems. The services have

  17. Lift augmentation for highly swept wing aircraft

    Science.gov (United States)

    Rao, Dhanvada M. (Inventor)

    1993-01-01

    A pair of spaced slots, disposed on each side of an aircraft centerline and spaced well inboard of the wing leading edges, are provided in the wing upper surfaces and directed tangentially spanwise toward thin sharp leading wing edges of a highly swept, delta wing aircraft. The slots are individually connected through separate plenum chambers to separate compressed air tanks and serve, collectively, as a system for providing aircraft lift augmentation. A compressed air supply is tapped from the aircraft turbojet power plant. Suitable valves, under the control of the aircraft pilot, serve to selective provide jet blowing from the individual slots to provide spanwise sheets of jet air closely adjacent to the upper surfaces and across the aircraft wing span to thereby create artificial vortices whose suction generate additional lift on the aircraft. When desired, or found necessary, unequal or one-side wing blowing is employed to generate rolling moments for augmented lateral control. Trailing flaps are provided that may be deflected differentially, individually, or in unison, as needed for assistance in take-off or landing of the aircraft.

  18. Wetting Characteristics of Insect Wing Surfaces

    Institute of Scientific and Technical Information of China (English)

    Doyoung Byun; Jongin Hong; Saputra; Jin Hwan Ko; Young Jong Lee; Hoon Cheol Park; Bong-Kyu Byun; Jennifer R. Lukes

    2009-01-01

    Biological tiny structures have been observed on many kinds of surfaces such as lotus leaves, which have an effect on the coloration of Morpho butterflies and enhance the hydrophobicity of natural surfaces. We investigated the micro-scale and nano-scale structures on the wing surfaces of insects and found that the hierarchical multiple roughness structures help in enhancing the hydrophobicity. After examining 10 orders and 24 species of flying Pterygotan insects, we found that micro-scale and nano-scale structures typically exist on both the upper and lower wing surfaces of flying insects. The tiny structures such as denticle or setae on the insect wings enhance the hydrophobicity, thereby enabling the wings to be cleaned more easily. And the hydrophobic insect wings undergo a transition from Cassie to Wenzel states at pitch/size ratio of about 20. In order to examine the wetting characteristics on a rough surface, a biomimetic surface with micro-scale pillars is fabricated on a silicon wafer,which exhibits the same behavior as the insect wing, with the Cassie-Wenzel transition occurring consistently around a pitch/width value of 20.

  19. The leading-edge vortex of swift wing-shaped delta wings.

    Science.gov (United States)

    Muir, Rowan Eveline; Arredondo-Galeana, Abel; Viola, Ignazio Maria

    2017-08-01

    Recent investigations on the aerodynamics of natural fliers have illuminated the significance of the leading-edge vortex (LEV) for lift generation in a variety of flight conditions. A well-documented example of an LEV is that generated by aircraft with highly swept, delta-shaped wings. While the wing aerodynamics of a manoeuvring aircraft, a bird gliding and a bird in flapping flight vary significantly, it is believed that this existing knowledge can serve to add understanding to the complex aerodynamics of natural fliers. In this investigation, a model non-slender delta-shaped wing with a sharp leading edge is tested at low Reynolds number, along with a delta wing of the same design, but with a modified trailing edge inspired by the wing of a common swift Apus apus. The effect of the tapering swift wing on LEV development and stability is compared with the flow structure over the unmodified delta wing model through particle image velocimetry. For the first time, a leading-edge vortex system consisting of a dual or triple LEV is recorded on a swift wing-shaped delta wing, where such a system is found across all tested conditions. It is shown that the spanwise location of LEV breakdown is governed by the local chord rather than Reynolds number or angle of attack. These findings suggest that the trailing-edge geometry of the swift wing alone does not prevent the common swift from generating an LEV system comparable with that of a delta-shaped wing.

  20. Numerical study of the trailing vortex of a wing with wing-tip blowing

    Science.gov (United States)

    Lim, Hock-Bin

    1994-01-01

    Trailing vortices generated by lifting surfaces such as helicopter rotor blades, ship propellers, fixed wings, and canard control surfaces are known to be the source of noise, vibration, cavitation, degradation of performance, and other hazardous problems. Controlling these vortices is, therefore, of practical interest. The formation and behavior of the trailing vortices are studied in the present research. In addition, wing-tip blowing concepts employing axial blowing and spanwise blowing are studied to determine their effectiveness in controlling these vortices and their effects on the performance of the wing. The 3D, unsteady, thin-layer compressible Navier-Stokes equations are solved using a time-accurate, implicit, finite difference scheme that employs LU-ADI factorization. The wing-tip blowing is simulated using the actuator plane concept, thereby, not requiring resolution of the jet slot geometry. Furthermore, the solution blanking feature of the chimera scheme is used to simplify the parametric study procedure for the wing-tip blowing. Computed results are shown to compare favorably with experimental measurements. It is found that axial wing-tip blowing, although delaying the rolling-up of the trailing vortices and the near-field behavior of the flowfield, does not dissipate the circulation strength of the trailing vortex farther downstream. Spanwise wing-tip blowing has the effect of displacing the trailing vortices outboard and upward. The increased 'wing-span' due to the spanwise wing-tip blowing has the effect of lift augmentation on the wing and the strengthening of the trailing vortices. Secondary trailing vortices are created at high spanwise wing-tip blowing intensities.

  1. Populists in Parliament : Comparing Left-Wing and Right-Wing Populism in the Netherlands

    NARCIS (Netherlands)

    Otjes, Simon; Louwerse, Tom

    2015-01-01

    In parliament, populist parties express their positions almost every day through voting. There is great diversity among them, for instance between left-wing and right-wing populist parties. This gives rise to the question: is the parliamentary behaviour of populists motivated by their populism or by

  2. Aerodynamics of two-dimensional flapping wings in tandem configuration

    Science.gov (United States)

    Lua, K. B.; Lu, H.; Zhang, X. H.; Lim, T. T.; Yeo, K. S.

    2016-12-01

    This paper reports a fundamental investigation on the aerodynamics of two-dimensional flapping wings in tandem configuration in forward flight. Of particular interest are the effects of phase angle (φ) and center-to-center distance (L) between the front wing and the rear wing on the aerodynamic force generation at a Reynolds number of 5000. Both experimental and numerical methods were employed. A force sensor was used to measure the time-history aerodynamic forces experienced by the two wings and digital particle image velocimetry was utilized to obtain the corresponding flow structures. Both the front wing and the rear wing executed the same simple harmonic motions with φ ranging from -180° to 180° and four values of L, i.e., 1.5c, 2c, 3c, and 4c (c is the wing chord length). Results show that at fixed L = 2c, tandem wings perform better than the sum of two single wings that flap independently in terms of thrust for phase angle approximately from -90° to 90°. The maximum thrust on the rear wing occurs during in-phase flapping (φ = 0°). Correlation of transient thrust and flow structure indicates that there are generally two types of wing-wake interactions, depending on whether the rear wing crosses the shear layer shed from the front wing. Finally, increasing wing spacing has similar effect as reducing the phase angle, and an approximate mathematical model is derived to describe the relationship between these two parameters.

  3. Aerodynamics of wings at low Reynolds numbers: Boundary layer separation and reattachment

    Science.gov (United States)

    McArthur, John

    the drag increase is really caused by the formation of a laminar separation bubble. The results clearly indicate that the reverse is true, and that the subsequent drag decrease is caused by the laminar separation bubble. Part III. The leading edge vortex. Four wings with different sweep angles were studied at Reynolds number 5x104: sweep angles of 0, 20, 40, and 60 degrees. The wings had a simple cambered plate airfoil similar to the cambered airfoil of part I above. Each wing was built to have the same aspect ratio, wing area, and streamwise airfoil shape. Previous studies on bird wings speculate that simply sweeping the wings can cause a leading edge vortex to form, which could cause substantial improvements in performance. However, these studies were not well controlled, and were conducted from a biological perspective. Qualitative and quantitative flow field measurements were combined with force measurements to conduct a well controlled engineering experiment on the formation and effect of a leading edge vortex on simple swept wings. A stable vortex was found to form over the 60 degree swept wing at one particular angle of attack, but it was not similar to the traditional notion of a leading edge vortex. The vortex has a small radius, and extends over little of the span. Force measurements indicate that the vortex has no significant impact on the forces measured. Thus, simply sweeping a wing is not sufficient to form a significant leading edge vortex, and other effects must be considered.

  4. Control of Flow Structure on Non-Slender Delta Wing: Bio-inspired Edge Modifications, Passive Bleeding, and Pulsed Blowing

    Science.gov (United States)

    Yavuz, Mehmet Metin; Celik, Alper; Cetin, Cenk

    2016-11-01

    In the present study, different flow control approaches including bio-inspired edge modifications, passive bleeding, and pulsed blowing are introduced and applied for the flow over non-slender delta wing. Experiments are conducted in a low speed wind tunnel for a 45 degree swept delta wing using qualitative and quantitative measurement techniques including laser illuminated smoke visualization, particle image velocimety (PIV), and surface pressure measurements. For the bio-inspired edge modifications, the edges of the wing are modified to dolphin fluke geometry. In addition, the concept of flexion ratio, a ratio depending on the flexible length of animal propulsors such as wings, is introduced. For passive bleeding, directing the free stream air from the pressure side of the planform to the suction side of the wing is applied. For pulsed blowing, periodic air injection through the leading edge of the wing is performed in a square waveform with 25% duty cycle at different excitation frequencies and compared with the steady and no blowing cases. The results indicate that each control approach is quite effective in terms of altering the overall flow structure on the planform. However, the success level, considering the elimination of stall or delaying the vortex breakdown, depends on the parameters in each method.

  5. Flapping wing aerodynamics: from insects to vertebrates.

    Science.gov (United States)

    Chin, Diana D; Lentink, David

    2016-04-01

    More than a million insects and approximately 11,000 vertebrates utilize flapping wings to fly. However, flapping flight has only been studied in a few of these species, so many challenges remain in understanding this form of locomotion. Five key aerodynamic mechanisms have been identified for insect flight. Among these is the leading edge vortex, which is a convergent solution to avoid stall for insects, bats and birds. The roles of the other mechanisms - added mass, clap and fling, rotational circulation and wing-wake interactions - have not yet been thoroughly studied in the context of vertebrate flight. Further challenges to understanding bat and bird flight are posed by the complex, dynamic wing morphologies of these species and the more turbulent airflow generated by their wings compared with that observed during insect flight. Nevertheless, three dimensionless numbers that combine key flow, morphological and kinematic parameters - the Reynolds number, Rossby number and advance ratio - govern flapping wing aerodynamics for both insects and vertebrates. These numbers can thus be used to organize an integrative framework for studying and comparing animal flapping flight. Here, we provide a roadmap for developing such a framework, highlighting the aerodynamic mechanisms that remain to be quantified and compared across species. Ultimately, incorporating complex flight maneuvers, environmental effects and developmental stages into this framework will also be essential to advancing our understanding of the biomechanics, movement ecology and evolution of animal flight.

  6. Antifatigue properties of dragonfly Pantala flavescens wings.

    Science.gov (United States)

    Li, Xiu-Juan; Zhang, Zhi-Hui; Liang, Yun-Hong; Ren, Lu-Quan; Jie, Meng; Yang, Zhi-Gang

    2014-05-01

    The wing of a dragonfly is thin and light, but can bear high frequent alternating stress and present excellent antifatigue properties. The surface morphology and microstructure of the wings of dragonfly Pantala flavescens were observed using SEM in this study. Based on the biological analysis method, the configuration, morphology, and structure of the vein were studied, and the antifatigue properties of the wings were investigated. The analytical results indicated that the longitudinal veins, cross veins, and membrane of dragonfly wing form a optimized network morphology and spacially truss-like structure which can restrain the formation and propagation of the fatigue cracks. The veins with multilayer structure present high strength, flexibility, and toughness, which are beneficial to bear alternating load during the flight of dragonfly. Through tensile-tensile fatigue failure tests, the results were verified and indicate that the wings of dragonfly P. flavescens have excellent antifatigue properties which are the results of the biological coupling and synergistic effect of morphological and structural factors.

  7. Elastic deformation and energy loss of flapping fly wings.

    Science.gov (United States)

    Lehmann, Fritz-Olaf; Gorb, Stanislav; Nasir, Nazri; Schützner, Peter

    2011-09-01

    During flight, the wings of many insects undergo considerable shape changes in spanwise and chordwise directions. We determined the origin of spanwise wing deformation by combining measurements on segmental wing stiffness of the blowfly Calliphora vicina in the ventral and dorsal directions with numerical modelling of instantaneous aerodynamic and inertial forces within the stroke cycle using a two-dimensional unsteady blade elementary approach. We completed this approach by an experimental study on the wing's rotational axis during stroke reversal. The wing's local flexural stiffness ranges from 30 to 40 nN m(2) near the root, whereas the distal wing parts are highly compliant (0.6 to 2.2 nN m(2)). Local bending moments during wing flapping peak near the wing root at the beginning of each half stroke due to both aerodynamic and inertial forces, producing a maximum wing tip deflection of up to 46 deg. Blowfly wings store up to 2.30 μJ elastic potential energy that converts into a mean wing deformation power of 27.3 μW. This value equates to approximately 5.9 and 2.3% of the inertial and aerodynamic power requirements for flight in this animal, respectively. Wing elasticity measurements suggest that approximately 20% or 0.46 μJ of elastic potential energy cannot be recovered within each half stroke. Local strain energy increases from tip to root, matching the distribution of the wing's elastic protein resilin, whereas local strain energy density varies little in the spanwise direction. This study demonstrates a source of mechanical energy loss in fly flight owing to spanwise wing bending at the stroke reversals, even in cases in which aerodynamic power exceeds inertial power. Despite lower stiffness estimates, our findings are widely consistent with previous stiffness measurements on insect wings but highlight the relationship between local flexural stiffness, wing deformation power and energy expenditure in flapping insect wings.

  8. Principle of bio-inspired insect wing rotational hinge design

    Science.gov (United States)

    Fei, Fan

    A principle for designing and fabricating bio-inspired miniature artificial insect flapping wing using flexure rotational hinge design is presented. A systematic approach of selecting rotational hinge stiffness value is proposed. Based on the understanding of flapping wing aerodynamics, a dynamic simulation is constructed using the established quasi-steady model and the wing design. Simulations were performed to gain insight on how different parameters affect the wing rotational response. Based on system resonance a model to predict the optimal rotational hinge stiffness based on given wing parameter and flapping wing kinematic is proposed. By varying different wing parameters, the proposed method is shown to be applicable to a wide range of wing designs with different sizes and shapes. With the selected hinge stiffness value, aspects of the rotational joint design is discussed and an integrated wing-hinge structure design using laminated carbon fiber and polymer film is presented. Manufacturing process of such composite structure is developed to achieve high accuracy and repeatability. The yielded hinge stiffness is verified by measurements. To validate the proposed model, flapping wing experiments were conducted. A flapping actuation set up is built using DC motor and a controller is implemented on a microcontroller to track desired wing stroke kinematic. Wing stroke and rotation kinematic were extracted using a high speed camera and the lift generation is evaluated. A total of 49 flapping experiments were presented, experimental data shows good correlation with the model's prediction. With the wing rotational hinge stiffness designed so that the rotational resonant frequency is twice as the stroke frequency, the resulting wing rotation generates near optimal lift. With further simulation, the proposed model shows low sensitivity to wing parameter variation. As a result, giving a design parameter of a flapping wing robot platform, the proposed principle can

  9. Inverse Degree and Connectivity

    Institute of Scientific and Technical Information of China (English)

    MA Xiao-ling; TIAN Ying-zhi

    2013-01-01

    Let G be a connected graph with vertex set V(G),order n =丨V(G)丨,minimum degree δ(G) and connectivity κ(G).The graph G is called maximally connected if κ(G) =δ(G).Define the inverse degree of G with no isolated vertices as R(G) =Σv∈V(G)1/d(v),where d(v) denotes the degree of the vertex v.We show that G is maximally connected if R(G) < 1 + 2/δ + n-2δ+1/(n-1)(n-3).

  10. An Analog Implementation of Fixed-Wing Lateral/Directional Dynamics and Guidelines on Aircraft Simulations in the Engineering Laboratory.

    Science.gov (United States)

    Karayanakis, Nicholas M.

    1985-01-01

    Describes a scheme for the mechanization of fixed-wing, lateral/directional dynamics as demonstrated on the EAI 580 analog/hybrid system. A review of the complete six degrees of freedom program is included, along with useful guidelines of aircraft simulation in the engineering laboratory. (Author/JN)

  11. In situ, real-time measurement of wing tilt during lateral epitaxial overgrowth of GaN

    Energy Technology Data Exchange (ETDEWEB)

    Fini, P. [Materials Department, University of California, Santa Barbara, Santa Barbara, California 93106 (United States); Munkholm, A. [Chemistry Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Thompson, Carol [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Stephenson, G. B. [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Eastman, J. A. [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Murty, M. V. Ramana [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Auciello, O. [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Zhao, L. [Materials Department, University of California, Santa Barbara, Santa Barbara, California 93106 (United States); DenBaars, S. P. [Materials Department, University of California, Santa Barbara, Santa Barbara, California 93106 (United States); Speck, J. S. [Materials Department, University of California, Santa Barbara, Santa Barbara, California 93106 (United States)

    2000-06-26

    By performing in situ, real-time x-ray diffraction measurements in the metalorganic chemical-vapor deposition environment, we have directly observed the emergence and evolution of wing tilt that occurs during the lateral overgrowth of GaN from stripes patterned in a SiO{sub 2} mask. This was done by repeatedly performing line scans through the 101(bar sign)3 peak in the direction perpendicular to the [101(bar sign)0]{sub GaN} stripe direction. The wing tilt developed as soon as the wings started forming, and increased slightly thereafter to reach a value of {approx}1.19 degree sign after 3600 s of growth. Upon cooldown to room temperature, the tilt increased to {approx}1.36 degree sign , indicating that thermally induced stresses during cooldown have only a small effect on wing tilt. However, changes in mask density, composition, and stress state during early lateral overgrowth must be considered as possible origins of wing tilt. (c) 2000 American Institute of Physics.

  12. Aeroelastic Analysis of Modern Complex Wings

    Science.gov (United States)

    Kapania, Rakesh K.; Bhardwaj, Manoj K.; Reichenbach, Eric; Guruswamy, Guru P.

    1996-01-01

    A process is presented by which aeroelastic analysis is performed by using an advanced computational fluid dynamics (CFD) code coupled with an advanced computational structural dynamics (CSD) code. The process is demonstrated on an F/A-18 Stabilator using NASTD (an in-house McDonnell Douglas Aerospace East CFD code) coupled with NASTRAN. The process is also demonstrated on an aeroelastic research wing (ARW-2) using ENSAERO (an in-house NASA Ames Research Center CFD code) coupled with a finite element wing-box structures code. Good results have been obtained for the F/A-18 Stabilator while results for the ARW-2 supercritical wing are still being obtained.

  13. Transonic flow theory of airfoils and wings

    Energy Technology Data Exchange (ETDEWEB)

    Garabedian, P R

    1976-01-01

    Supercritical wing technology is expected to have a significant influence on the next generation of commercial aircraft. Computational fluid dynamics is playing a central role in the development of new supercritical wing sections. One of the principal tools is a fast and reliable code that simulates two-dimensional wind tunnel data for transonic flow at high Reynolds numbers. This is used widely by industry to assess drag creep and drag rise. Codes for the design of shockless airfoils by the hodograph method have not been so well received because they usually require a lot of trial and error. However, a more advanced mathematical approach makes it possible to assign the pressure as a function of the arc length and then obtain a shockless airfoil that nearly achieves the given distribution of pressure. This tool should enable engineers to design families of transonic airfoils more easily both for airplane wings and for compressor blades in cascade.

  14. Degree by Thesis

    Science.gov (United States)

    Courtis, Barbara

    1974-01-01

    Discusses a student's experience with a research project on the synthesis and reactions of an organo-platinum complex with an organo-Group IV linkage, including the advantages and disadvantages of such a degree by thesis course. (CC)

  15. A finite element parametric modeling technique of aircraft wing structures

    Institute of Scientific and Technical Information of China (English)

    Tang Jiapeng; Xi Ping; Zhang Baoyuan; Hu Bifu

    2013-01-01

    A finite element parametric modeling method of aircraft wing structures is proposed in this paper because of time-consuming characteristics of finite element analysis pre-processing. The main research is positioned during the preliminary design phase of aircraft structures. A knowledge-driven system of fast finite element modeling is built. Based on this method, employing a template parametric technique, knowledge including design methods, rules, and expert experience in the process of modeling is encapsulated and a finite element model is established automatically, which greatly improves the speed, accuracy, and standardization degree of modeling. Skeleton model, geometric mesh model, and finite element model including finite element mesh and property data are established on parametric description and automatic update. The outcomes of research show that the method settles a series of problems of parameter association and model update in the pro-cess of finite element modeling which establishes a key technical basis for finite element parametric analysis and optimization design.

  16. Experimental Investigation on Aerodynamic Characteristics of a Paraglider Wing

    Science.gov (United States)

    Mashud, Mohammad; Umemura, Akira

    The fundamental aerodynamic characteristics of a paraglider’s canopy are investigated in wind tunnel experiments using an inflatable cell model designed to represent the dynamic behaviors of each cell comprising the canopy. At attack angles greater than a few degrees, the cell model inflates fully. To characterize its aerodynamic characteristics, we focus our attention on the flow around the inflated cell model at the plane of symmetry of the model. The cross-sectional profile of the inflated cell model, streamline pattern, internal air pressure and external surface pressure distribution are measured at various attack angles in order to identify the function of air intake and to obtain the lift and drag coefficients of the airfoil with an open air intake. The results reveal the mechanism of how the cell inflates into a stable wing shape and bears the buckling force caused by the cables suspending a pay load.

  17. A study on forces acting on a flapping wing

    Directory of Open Access Journals (Sweden)

    Cetiner O.

    2013-04-01

    Full Text Available In order to study the forces acting on a flapping wing, an experimental investigation is performed in steady water flow. In this study, a SD7003 airfoil undergoes combined pitching and plunging motion which simulates the forward flight of small birds. The frequency of pitching motion is equal to the frequency of plunging motion and pitch leads the plunge by a phase angle of 90 degrees. The experiments are conducted at Reynolds numbers of 2500 ≤ Re ≤ 13700 and the vortex formation is recorded using the digital particle image velocimetry (DPIV technique. A prediction of thrust force and efficiency is calculated from the average wake deficit of DPIV data, the near-wake vorticity patterns and time dependent velocity vectors are determined to comment on the thrust and drag indication. Direct force measurements are attempted using a Force/Torque sensor which is capable of measuring forces and moments in three axial directions.

  18. Active Aeroelastic Tailoring of High-Aspect-Ratio Composite Wings

    Science.gov (United States)

    2005-09-01

    34 - 26000 , ......... . . . ...... . . .... .. .......................... ... - - ----------- 21000 ... ........... ~0 50 LOAD... ISO 5: B s mission....f Figure 5: Basic mission profile 7 Figure 6: Baseline single-wing and joined-wing vehicles 3.1 Baseline vehicles Three sets

  19. X-31 Wing Storage for Shipping

    Science.gov (United States)

    1995-01-01

    The right wing of the X-31 Enhanced Fighter Maneuverability Technology Demonstrator Aircraft is seen here being put into a shipping container May 18, 1995, at NASA's Dryden Flight Research Center, Edwards, California, by U.S. and German members of the program. To fit inside an Air Force Reserve C-5 transport, which was used to ferry the X-31 to Europe on May 22, 1995, the right wing had to be removed. Manching, Germany, was used as a staging base to prepare the aircraft for participation in the Paris Air Show. At the air show on June 11 through the 18th, the X-31 demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with advanced flight control systems to provide controlled flight at very high angles of attack. The aircraft arrived back at Edwards in an Air Force Reserve C-5 on June 25, 1995, and off loaded at Dryden the 27th. The X-31 aircraft was developed jointly by Rockwell International's North American Aircraft Division (now part of Boeing) and Daimler-Benz Aerospace (formerly Messerschmitt-Bolkow-Blohm), under sponsorship by the U.S. Department of Defense and The German Federal Ministry of Defense. The X-31 Enhanced Fighter Maneuverability (EFM) demonstrator flew at the Ames- Dryden Flight Research Facility, Edwards, California (redesignated the Dryden Flight Research Center in 1994) from February 1992 until 1995 and before that at the Air Force's Plant 42 in Palmdale, California. The goal of the project was to provide design information for the next generation of highly maneuverable fighter aircraft. This program demonstrated the value of using thrust vectoring (directing engine exhaust flow) coupled with an advanced flight control system to provide controlled flight to very high angles of attack. The result was a significant advantage over most conventional fighters in close-in combat situations. The X-31 flight program focused on agile flight within the post-stall regime, producing technical data to give aircraft

  20. Decoupler pylon: wing/store flutter suppressor

    Science.gov (United States)

    Reed, W. H., III (Inventor)

    1982-01-01

    A device for suspending a store from a support such as an aircraft wing and more specifically for increasing the flutter speed of an aircraft flying with attached store and reducing the sensitivity of flutter to changes in the pitch inertia and center of gravity location of the store is described. It comprises softspring where the store pitch mode is decoupled from support modes and a low frequency active control mechanism which maintains store alignment. A pneumatic suspension system both isolates the store in pitch and, under conditions of changing mean load, aligns the store with the wing to which it is attached.

  1. Calculated Unsteady Aerodynamics of Wings.

    Science.gov (United States)

    1987-12-15

    test-and- evaluation turnaround time of only a few minutes per case. The following sections outline the derivation and implementation of this...computer program. Inputs degrees at the higher end, and is purely a numerical to the prgram include the threshold vortex offset dis- error. The present...precise + - (4.2) aumerical evaluation . U . P U. The (non-linear) expressions for lift and moment includ- I R cidt"() eC ca 1 rig the appropriate wake

  2. Spanwise transition section for blended wing-body aircraft

    Science.gov (United States)

    Hawley, Arthur V. (Inventor)

    1999-01-01

    A blended wing-body aircraft includes a central body, a wing, and a transition section which interconnects the body and the wing on each side of the aircraft. The two transition sections are identical, and each has a variable chord length and thickness which varies in proportion to the chord length. This enables the transition section to connect the thin wing to the thicker body. Each transition section has a negative sweep angle.

  3. Design and aerodynamic characteristics of a span morphing wing

    Science.gov (United States)

    Yu, Yuemin; Liu, Yanju; Leng, Jinsong

    2009-03-01

    Flight vehicles are often designed to function around a primary operating point such as an efficient cruise or a high maneuverability mode. Performance and efficiency deteriorate rapidly as the airplane moves towards other portions of the flight envelope. One solution to this quandary is to radically change the shape of the aircraft. This yields both improved efficiency and a larger flight envelope. This global shape change is an example of morphing aircraft . One concept of morphing is the span morphing wing in which the wingspan is varied to accommodate multiple flight regimes. This type of design allows for at least two discreet modes of the aircraft. The original configuration, in which the extensible portion of the wing is fully retracted, yields a high speed dash mode. Fully extending the wing provides the aircraft with a low speed mode tailored for fine tracking and loiter tasks. This paper discusses the design of a span morphing wing that permits a change in the aspect ratio while simultaneously supporting structural wing loads. The wing cross section is maintained by NACA 4412 rib sections . The span morphing wing was investigated in different configurations. The wing area and the aspect ratio of the span morphing wing increase as the wings pan increases. Computational aerodynamics are used to estimate the performance and dynamic characteristics of each wing shape of this span morphing wing as its wingspan is changed. Results show that in order to obtain the same lift, the conventional wing requires a larger angle of attach(AOA) than that of the span morphing wing.The lift of the span morphing wing increases as the wing span ,Mach number and AOA increases.

  4. Nonlinear, unsteady aerodynamic loads on rectangular and delta wings

    Science.gov (United States)

    Atta, E. H.; Kandil, O. A.; Mook, D. T.; Nayfeh, A. H.

    1977-01-01

    Nonlinear unsteady aerodynamic loads on rectangular and delta wings in an incompressible flow are calculated by using an unsteady vortex-lattice model. Examples include flows past fixed wings in unsteady uniform streams and flows past wings undergoing unsteady motions. The unsteadiness may be due to gusty winds or pitching oscillations. The present technique establishes a reliable approach which can be utilized in the analysis of problems associated with the dynamics and aeroelasticity of wings within a wide range of angles of attack.

  5. Ornithopter type flapping wings for autonomous micro air vehicles

    OpenAIRE

    2015-01-01

    In this paper, an ornithopter prototype that mimics the flapping motion of bird flight is developed, and the lift and thrust generation characteristics of different wing designs are evaluated. This project focused on the spar arrangement and material used for the wings that could achieves improved performance. Various lift and thrust measurement techniques are explored and evaluated. Various wings of insects and birds were evaluated to understand how these natural flyers with flapping wings a...

  6. Turboelectric Distributed Propulsion in a Hybrid Wing Body Aircraft

    Science.gov (United States)

    Felder, James L.; Brown, Gerald V.; DaeKim, Hyun; Chu, Julio

    2011-01-01

    The performance of the N3-X, a 300 passenger hybrid wing body (HWB) aircraft with turboelectric distributed propulsion (TeDP), has been analyzed to see if it can meet the 70% fuel burn reduction goal of the NASA Subsonic Fixed Wing project for N+3 generation aircraft. The TeDP system utilizes superconducting electric generators, motors and transmission lines to allow the power producing and thrust producing portions of the system to be widely separated. It also allows a small number of large turboshaft engines to drive any number of propulsors. On the N3-X these new degrees of freedom were used to (1) place two large turboshaft engines driving generators in freestream conditions to maximize thermal efficiency and (2) to embed a broad continuous array of 15 motor driven propulsors on the upper surface of the aircraft near the trailing edge. That location maximizes the amount of the boundary layer ingested and thus maximizes propulsive efficiency. The Boeing B777-200LR flying 7500 nm (13890 km) with a cruise speed of Mach 0.84 and an 118100 lb payload was selected as the reference aircraft and mission for this study. In order to distinguish between improvements due to technology and aircraft configuration changes from those due to the propulsion configuration changes, an intermediate configuration was included in this study. In this configuration a pylon mounted, ultra high bypass (UHB) geared turbofan engine with identical propulsion technology was integrated into the same hybrid wing body airframe. That aircraft achieved a 52% reduction in mission fuel burn relative to the reference aircraft. The N3-X was able to achieve a reduction of 70% and 72% (depending on the cooling system) relative to the reference aircraft. The additional 18% - 20% reduction in the mission fuel burn can therefore be attributed to the additional degrees of freedom in the propulsion system configuration afforded by the TeDP system that eliminates nacelle and pylon drag, maximizes boundary

  7. Titanium honeycomb structure. [for supersonic aircraft wing structure

    Science.gov (United States)

    Davis, R. A.; Elrod, S. D.; Lovell, D. T.

    1972-01-01

    A brazed titanium honeycomb sandwich system for supersonic transport wing cover panels provides the most efficient structure spanwise, chordwise, and loadwise. Flutter testing shows that high wing stiffness is most efficient in a sandwich structure. This structure also provides good thermal insulation if liquid fuel is carried in direct contact with the wing structure in integral fuel tanks.

  8. How swifts control their glide performance with morphing wings

    NARCIS (Netherlands)

    Lentink, D.; Muller, U. K.; Stamhuis, E. J.; de Kat, R.; van Gestel, W.; Veldhuis, L. L. M.; Henningsson, P.; Hedenstrom, A.; Videler, J. J.

    2007-01-01

    Gliding birds continually change the shape and size of their wings(1-6), presumably to exploit the profound effect of wing morphology on aerodynamic performance(7-9). That birds should adjust wing sweep to suit glide speed has been predicted qualitatively by analytical glide models(2,10), which extr

  9. A Wind Tunnel Investigation of Joined Wing Scissor Morphing

    Science.gov (United States)

    2006-06-01

    wing stalls when the rear wing stalls [23]. While this improves efficiency it also decreases the wetted area while maintaining the same lifting...Analysis and Optimization on Joined-Wing Configurations. Dir. Dong-Hwan Lee and P. C. Chen. Slide Program. Zona Technology. 2. Bagwill, Tracy L., and

  10. How swifts control their glide performance with morphing wings

    NARCIS (Netherlands)

    Lentink, D.; Müller, U.K.; Stamhuis, E.J.; Kat, de R.; Gestel, van W.J.H.; Veldhuis, L.L.M.; Henningsson, P.; Hedenström, A.; Videler, J.J.; Leeuwen, van J.L.

    2007-01-01

    Gliding birds continually change the shape and size of their wings1, 2, 3, 4, 5, 6, presumably to exploit the profound effect of wing morphology on aerodynamic performance7, 8, 9. That birds should adjust wing sweep to suit glide speed has been predicted qualitatively by analytical glide models2, 10

  11. A Layout Optimization Method of Composite Wing Structures Based on Carrying Efficiency Criterion

    Institute of Scientific and Technical Information of China (English)

    ZHAO Qun; DING Yunliang; JIN Haibo

    2011-01-01

    A two-level layout optimization strategy is proposed in this paper for large-scale composite wing structures.Design requirements are adjusted at the system level according to structural deformation,while the layout is optimized at the subsystem level to satisfy the constraints from system level.The approaching degrees of various failure critical loads in wing panels are employed to gauge the structure's carrying efficiency.By optimizing the efficiency as an objective,the continuity of the problem could be guaranteed.Stiffened wing panels are modeled by the equivalent orthotropic plates,and the global buckling load is predicted by energy method.The nonlinear effect of stringers' support elasticity on skin local buckle resistance is investigated and approximated by neural network(NN) surrogate model.These failure predictions are based on analytical solutions,which could effectively save calculation resources.Finally,the integral optimization of a large-scale wing structure is completed as an example.The result fulfills design requirements and shows the feasibility of this method.

  12. Pressure measurements on a rectangular wing with a NACA0012 airfoil during conventional flutter

    Science.gov (United States)

    Rivera, Jose A., Jr.; Dansberry, Bryan E.; Durham, Michael H.; Bennett, Robert M.; Silva, Walter A.

    1992-01-01

    The Structural Dynamics Division at NASA LaRC has started a wind tunnel activity referred to as the Benchmark Models Program. The primary objective of the program is to acquire measured dynamic instability and corresponding pressure data that will be useful for developing and evaluating aeroelastic type CFD codes currently in use or under development. The program is a multi-year activity that will involve testing of several different models to investigate various aeroelastic phenomena. The first model consisted of a rigid semispan wing having a rectangular planform and a NACA 0012 airfoil shape which was mounted on a flexible two degree-of-freedom mount system. Two wind-tunnel tests were conducted with the first model. Several dynamic instability boundaries were investigated such as a conventional flutter boundary, a transonic plunge instability region near Mach = 0.90, and stall flutter. In addition, wing surface unsteady pressure data were acquired along two model chords located at the 60 to 95-percent span stations during these instabilities. At this time, only the pressure data for the conventional flutter boundary is presented. The conventional flutter boundary and the wing surface unsteady pressure measurements obtained at the conventional flutter boundary test conditions in pressure coefficient form are presented. Wing surface steady pressure measurements obtained with the model mount system rigidized are also presented. These steady pressure data were acquired at essentially the same dynamic pressure at which conventional flutter had been encountered with the mount system flexible.

  13. The costae presenting in high-temperature-induced vestigial wings of Drosophila: implications for anterior wing margin formation

    Indian Academy of Sciences (India)

    Daxiang Yang

    2007-01-01

    It has long been noted that high temperature produces great variation in wing forms of the vestigial mutant of Drosophila. Most of the wings have defects in the wing blade and partially formed wing margin, which are the result of autonomous cell death in the presumptive wing blade or costal region of the wing disc. The vestigial gene ($vg$) and the interaction of Vg protein with other gene products are well understood. With this biochemical knowledge, reinvestigations of the high-temperature-induced vestigial wings and the elucidation of the molecular mechanism underlying the large-scale variation of the wing forms may provide insight into further understanding of development of the wing of Drosophila. As a first step of such explorations, I examined high-temperature-induced (29°C) vestigial wings. In the first part of this paper, I provide evidences to show that the proximal and distal costae in these wings exhibit regular and continuous variation, which suggests different developmental processes for the proximal and distal costal sections. Judging by the costae presenting in the anterior wing margin, I propose that the proximal and distal costal sections are independent growth units. The genes that regulate formation of the distal costal section also strongly affect proliferation of cells nearby; however, the same phenomenon has not been found in the proximal costal section. The distal costal section seems to be an extension of the radius vein. vestigial, one of the most intensely researched temperature-sensitive mutations, is a good candidate for the study of marginal vein formation. In the second part of the paper, I regroup the wing forms of these wings, chiefly by comparison of venation among these wings, and try to elucidate the variation of the wing forms according to the results of previous work and the conclusions reached in the first part of this paper, and provide clues for further researches.

  14. Aeroelastic Analysis of SUGAR Truss-Braced Wing Wind-Tunnel Model Using FUN3D and a Nonlinear Structural Model

    Science.gov (United States)

    Bartels, Robert E.; Scott, Robert C.; Allen, Timothy J.; Sexton, Bradley W.

    2015-01-01

    Considerable attention has been given in recent years to the design of highly flexible aircraft. The results of numerous studies demonstrate the significant performance benefits of strut-braced wing (SBW) and trussbraced wing (TBW) configurations. Critical aspects of the TBW configuration are its larger aspect ratio, wing span and thinner wings. These aspects increase the importance of considering fluid/structure and control system coupling. This paper presents high-fidelity Navier-Stokes simulations of the dynamic response of the flexible Boeing Subsonic Ultra Green Aircraft Research (SUGAR) truss-braced wing wind-tunnel model. The latest version of the SUGAR TBW finite element model (FEM), v.20, is used in the present simulations. Limit cycle oscillations (LCOs) of the TBW wing/strut/nacelle are simulated at angle-of-attack (AoA) values of -1, 0 and +1 degree. The modal data derived from nonlinear static aeroelastic MSC.Nastran solutions are used at AoAs of -1 and +1 degrees. The LCO amplitude is observed to be dependent on AoA. LCO amplitudes at -1 degree are larger than those at +1 degree. The LCO amplitude at zero degrees is larger than either -1 or +1 degrees. These results correlate well with both wind-tunnel data and the behavior observed in previous studies using linear aerodynamics. The LCO onset at zero degrees AoA has also been computed using unloaded v.20 FEM modes. While the v.20 model increases the dynamic pressure at which LCO onset is observed, it is found that the LCO onset at and above Mach 0.82 is much different than that produced by an earlier version of the FEM, v. 19.

  15. Computational wing optimization and comparisons with experiment for a semi-span wing model

    Science.gov (United States)

    Waggoner, E. G.; Haney, H. P.; Ballhaus, W. F.

    1978-01-01

    A computational wing optimization procedure was developed and verified by an experimental investigation of a semi-span variable camber wing model in the NASA Ames Research Center 14 foot transonic wind tunnel. The Bailey-Ballhaus transonic potential flow analysis and Woodward-Carmichael linear theory codes were linked to Vanderplaats constrained minimization routine to optimize model configurations at several subsonic and transonic design points. The 35 deg swept wing is characterized by multi-segmented leading and trailing edge flaps whose hinge lines are swept relative to the leading and trailing edges of the wing. By varying deflection angles of the flap segments, camber and twist distribution can be optimized for different design conditions. Results indicate that numerical optimization can be both an effective and efficient design tool. The optimized configurations had as good or better lift to drag ratios at the design points as the best designs previously tested during an extensive parametric study.

  16. Aerodynamic Interactions Between Contralateral Wings and Between Wings and Body of a Model Insect at Hovering and Small Speed Motions

    Institute of Scientific and Technical Information of China (English)

    LIANG Bin; SUN Mao

    2011-01-01

    In this paper,we study the aerodynamic interactions between the contralateral wings and between the body and wings of a model insect,when the insect is hovering and has various translational and rotational motions,using the method numerically solving the Navier-Stokes equations over moving overset grids.The aerodynamic interactional effects are identified by comparing the results of a complete model insect,the corresponding wing pair,single wing and body without the wings.Horizontal,vertical and lateral translations and roll,pitch and yaw rotations at small speeds are considered.The results indicate that for the motions considered,both the interaction between the contralateral wings and the interaction between the body and wings are weak.The changes in the forces and moments of a wing due to the contralateral wing interaction,of the wings due to the presence of the body,and of the body due to the presence of the wings are generally less than 4.5%.Results show that aerodynamic forces of wings and body can be measured or computed separately in the analysis of flight stability and control of hovering insects.

  17. Aerodynamic comparison of a butterfly-like flapping wing-body model and a revolving-wing model

    Science.gov (United States)

    Suzuki, Kosuke; Yoshino, Masato

    2017-06-01

    The aerodynamic performance of flapping- and revolving-wing models is investigated by numerical simulations based on an immersed boundary-lattice Boltzmann method. As wing models, we use (i) a butterfly-like model with a body and flapping-rectangular wings and (ii) a revolving-wing model with the same wings as the flapping case. Firstly, we calculate aerodynamic performance factors such as the lift force, the power, and the power loading of the two models for Reynolds numbers in the range of 50-1000. For the flapping-wing model, the power loading is maximal for the maximum angle of attack of 90°, a flapping amplitude of roughly 45°, and a phase shift between the flapping angle and the angle of attack of roughly 90°. For the revolving-wing model, the power loading peaks for an angle of attack of roughly 45°. In addition, we examine the ground effect on the aerodynamic performance of the revolving-wing model. Secondly, we compare the aerodynamic performance of the flapping- and revolving-wing models at their respective maximal power loadings. It is found that the revolving-wing model is more efficient than the flapping-wing model both when the body of the latter is fixed and where it can move freely. Finally, we discuss the relative agilities of the flapping- and revolving-wing models.

  18. Fiber-optically sensorized composite wing

    Science.gov (United States)

    Costa, Joannes M.; Black, Richard J.; Moslehi, Behzad; Oblea, Levy; Patel, Rona; Sotoudeh, Vahid; Abouzeida, Essam; Quinones, Vladimir; Gowayed, Yasser; Soobramaney, Paul; Flowers, George

    2014-04-01

    Electromagnetic interference (EMI) immune and light-weight, fiber-optic sensor based Structural Health Monitoring (SHM) will find increasing application in aerospace structures ranging from aircraft wings to jet engine vanes. Intelligent Fiber Optic Systems Corporation (IFOS) has been developing multi-functional fiber Bragg grating (FBG) sensor systems including parallel processing FBG interrogators combined with advanced signal processing for SHM, structural state sensing and load monitoring applications. This paper reports work with Auburn University on embedding and testing FBG sensor arrays in a quarter scale model of a T38 composite wing. The wing was designed and manufactured using fabric reinforced polymer matrix composites. FBG sensors were embedded under the top layer of the composite. Their positions were chosen based on strain maps determined by finite element analysis. Static and dynamic testing confirmed expected response from the FBGs. The demonstrated technology has the potential to be further developed into an autonomous onboard system to perform load monitoring, SHM and Non-Destructive Evaluation (NDE) of composite aerospace structures (wings and rotorcraft blades). This platform technology could also be applied to flight testing of morphing and aero-elastic control surfaces.

  19. Applications of a transonic wing design method

    Science.gov (United States)

    Campbell, Richard L.; Smith, Leigh A.

    1989-01-01

    A method for designing wings and airfoils at transonic speeds using a predictor/corrector approach was developed. The procedure iterates between an aerodynamic code, which predicts the flow about a given geometry, and the design module, which compares the calculated and target pressure distributions and modifies the geometry using an algorithm that relates differences in pressure to a change in surface curvature. The modular nature of the design method makes it relatively simple to couple it to any analysis method. The iterative approach allows the design process and aerodynamic analysis to converge in parallel, significantly reducing the time required to reach a final design. Viscous and static aeroelastic effects can also be accounted for during the design or as a post-design correction. Results from several pilot design codes indicated that the method accurately reproduced pressure distributions as well as the coordinates of a given airfoil or wing by modifying an initial contour. The codes were applied to supercritical as well as conventional airfoils, forward- and aft-swept transport wings, and moderate-to-highly swept fighter wings. The design method was found to be robust and efficient, even for cases having fairly strong shocks.

  20. Conceptual Study of Rotary-Wing Microrobotics

    Science.gov (United States)

    2008-03-27

    xx  I.  Introduction ...Edge TPV Thermo-Photovoltaic CONCEPTUAL STUDY OF ROTARY-WING MICROROBOTICS I. Introduction Flying micro-robots offer unimaginable military...Tweezers 1989 1 cm3 inch robot 1991 Magnetostrictive mover in pipe 1992 Insect-based robot 1993 Ciliary-motion conveyor 1994 Pipe inspection robot

  1. Mother Nature inspires new wind turbine wing

    DEFF Research Database (Denmark)

    Sønderberg Petersen, L.

    2007-01-01

    The sight of a bird of prey hanging immobile in the air while its wings continuously adjust themselves slightly in relation to the wind in order to keep the bird in the same position in the air, is a sight that most of us have admired, including the windenergy scientists at Risø DTU. They have st...

  2. Can Wing Tip Vortices Be Accurately Simulated?

    Science.gov (United States)

    2011-07-01

    additional tail buffeting.2 In commercial applications, winglets have been installed on passenger aircraft to minimize vortex formation and reduce lift...air. In military applications, wing tip In commercial applications, winglets have been installed on passenger aircraft to minimize increases with downstream distances.

  3. Hybrid Wing Body Configuration Scaling Study

    Science.gov (United States)

    Nickol, Craig L.

    2012-01-01

    The Hybrid Wing Body (HWB) configuration is a subsonic transport aircraft concept with the potential to simultaneously reduce fuel burn, noise and emissions compared to conventional concepts. Initial studies focused on very large applications with capacities for up to 800 passengers. More recent studies have focused on the large, twin-aisle class with passenger capacities in the 300-450 range. Efficiently scaling this concept down to the single aisle or smaller size is challenging due to geometric constraints, potentially reducing the desirability of this concept for applications in the 100-200 passenger capacity range or less. In order to quantify this scaling challenge, five advanced conventional (tube-and-wing layout) concepts were developed, along with equivalent (payload/range/technology) HWB concepts, and their fuel burn performance compared. The comparison showed that the HWB concepts have fuel burn advantages over advanced tube-and-wing concepts in the larger payload/range classes (roughly 767-sized and larger). Although noise performance was not quantified in this study, the HWB concept has distinct noise advantages over the conventional tube-and-wing configuration due to the inherent noise shielding features of the HWB. NASA s Environmentally Responsible Aviation (ERA) project will continue to investigate advanced configurations, such as the HWB, due to their potential to simultaneously reduce fuel burn, noise and emissions.

  4. Aerodynamics of a rigid curved kite wing

    CERN Document Server

    Maneia, Gianmauro; Tordella, Daniela; Iovieno, Michele

    2013-01-01

    A preliminary numerical study on the aerodynamics of a kite wing for high altitude wind power generators is proposed. Tethered kites are a key element of an innovative wind energy technology, which aims to capture energy from the wind at higher altitudes than conventional wind towers. We present the results obtained from three-dimensional finite volume numerical simulations of the steady air flow past a three-dimensional curved rectangular kite wing (aspect ratio equal to 3.2, Reynolds number equal to 3x10^6). Two angles of incidence -- a standard incidence for the flight of a tethered airfoil (6{\\deg}) and an incidence close to the stall (18{\\deg}) -- were considered. The simulations were performed by solving the Reynolds Averaged Navier-Stokes flow model using the industrial STAR-CCM+ code. The overall aerodynamic characteristics of the kite wing were determined and compared to the aerodynamic characteristics of the flat rectangular non twisted wing with an identical aspect ratio and section (Clark Y profil...

  5. Migration on Wings Aerodynamics and Energetics

    CERN Document Server

    Kantha, Lakshmi

    2012-01-01

    This book is an effort to explore the technical aspects associated with bird flight and migration on wings. After a short introduction on the birds migration, the book reviews the aerodynamics and Energetics of Flight and presents the calculation of the Migration Range. In addition, the authors explains aerodynamics of the formation flight and finally introduces great flight diagrams.

  6. Topology Optimization of an Aircraft Wing

    Science.gov (United States)

    2015-06-11

    baseline products were built in Solidworks prior to the optimization process. Loading on the wing was applied for multiple aerodynamic profiles generating...redesign and placement of the fuel tank was desired. A simple model of the baseline tank was built in Solidworks to estimate the total volume. Overall

  7. ALICE Zero Degree Calorimeter

    CERN Multimedia

    De Marco, N

    2013-01-01

    Two identical sets of calorimeters are located on both sides with respect to the beam Interaction Point (IP), 112.5 m away from it. Each set of detectors consists of a neutron (ZN) and a proton (ZP) Zero Degree Calorimeter (ZDC), positioned on remotely controlled platforms. The ZN is placed at zero degree with respect to the LHC beam axis, between the two beam pipes, while the ZP is positioned externally to the outgoing beam pipe. The spectator protons are separated from the ion beams by means of the dipole magnet D1.

  8. Physics to a degree

    CERN Document Server

    Thomas, EG

    2014-01-01

    Physics to a Degree provides an extensive collection of problems suitable for self-study or tutorial and group work at the level of an undergraduate physics course. This novel set of exercises draws together the core elements of an undergraduate physics degree and provides students with the problem solving skills needed for general physics' examinations and for real-life situations encountered by the professional physicist. Topics include force, momentum, gravitation, Bernoulli's Theorem, magnetic fields, blackbody radiation, relativistic travel, mechanics near the speed of light, radioactive

  9. Aircraft energy efficiency laminar flow control wing design study

    Science.gov (United States)

    Bonner, T. F., Jr.; Pride, J. D., Jr.; Fernald, W. W.

    1977-01-01

    An engineering design study was performed in which laminar flow control (LFC) was integrated into the wing of a commercial passenger transport aircraft. A baseline aircraft configuration was selected and the wing geometry was defined. The LFC system, with suction slots, ducting, and suction pumps was integrated with the wing structure. The use of standard aluminum technology and advanced superplastic formed diffusion bonded titanium technology was evaluated. The results of the design study show that the LFC system can be integrated with the wing structure to provide a structurally and aerodynamically efficient wing for a commercial transport aircraft.

  10. Aerodynamics on a transport aircraft type wing-body model

    Science.gov (United States)

    Schmitt, V.

    1982-01-01

    The DFLR-F4 wing-body combination is studied. The 1/38 model is formed by a 9.5 aspect ratio transonic wing and an Airbus A 310 fuselage. The F4 wing geometrical characteristics are described and the main experimental results obtained in the S2MA wind tunnel are discussed. Both wing-fuselage interferences and viscous effects, which are important on the wing due to a high rear loading, are investigated by performing 3D calculations. An attempt is made to find their limitations.

  11. Investigation and design of a C-Wing passenger aircraft

    OpenAIRE

    Karan BIKKANNAVAR; Scholz, Dieter

    2016-01-01

    A novel nonplanar wing concept called C-Wing is studied and implemented on a commercial aircraft to reduce induced drag which has a significant effect on fuel consumption. A preliminary sizing method which employs an optimization algorithm is utilized. The Airbus A320 aircraft is used as a reference aircraft to evaluate design parameters and to investigate the C-Wing design potential beyond current wing tip designs. An increase in aspect ratio due to wing area reduction at 36m span results in...

  12. Registered Nurse (Associate Degree).

    Science.gov (United States)

    Ohio State Univ., Columbus. Center on Education and Training for Employment.

    This document, which is designed for use in developing a tech prep competency profile for the occupation of registered nurse (with an associate degree), lists technical competencies and competency builders for 19 units pertinent to the health technologies cluster in general and 5 units specific to the occupation of registered nurse. The following…

  13. One Degree of Separation

    Science.gov (United States)

    Johnson, Jean

    2012-01-01

    A 2011 survey of young adults conducted by Public Agenda found that a cluster of obstacles have prevented many of them from competing college. The author describes the opportunity, college awareness, and funding gaps that put a postsecondary degree out of the reach of so many young people. For example, just 3 in 10 non-college-completers are aware…

  14. Large capacity oblique all-wing transport aircraft

    Science.gov (United States)

    Galloway, Thomas L.; Phillips, James A.; Kennelly, Robert A., Jr.; Waters, Mark H.

    1996-01-01

    Dr. R. T. Jones first developed the theory for oblique wing aircraft in 1952, and in subsequent years numerous analytical and experimental projects conducted at NASA Ames and elsewhere have established that the Jones' oblique wing theory is correct. Until the late 1980's all proposed oblique wing configurations were wing/body aircraft with the wing mounted on a pivot. With the emerging requirement for commercial transports with very large payloads, 450-800 passengers, Jones proposed a supersonic oblique flying wing in 1988. For such an aircraft all payload, fuel, and systems are carried within the wing, and the wing is designed with a variable sweep to maintain a fixed subsonic normal Mach number. Engines and vertical tails are mounted on pivots supported from the primary structure of the wing. The oblique flying wing transport has come to be known as the Oblique All-Wing (OAW) transport. This presentation gives the highlights of the OAW project that was to study the total concept of the OAW as a commercial transport.

  15. Multiple cues for winged morph production in an aphid metacommunity.

    Directory of Open Access Journals (Sweden)

    Mohsen Mehrparvar

    Full Text Available Environmental factors can lead individuals down different developmental pathways giving rise to distinct phenotypes (phenotypic plasticity. The production of winged or unwinged morphs in aphids is an example of two alternative developmental pathways. Dispersal is paramount in aphids that often have a metapopulation structure, where local subpopulations frequently go extinct, such as the specialized aphids on tansy (Tanacetum vulgare. We conducted various experiments to further understand the cues involved in the production of winged dispersal morphs by the two dominant species of the tansy aphid metacommunity, Metopeurum fuscoviride and Macrosiphoniella tanacetaria. We found that the ant-tended M. fuscoviride produced winged individuals predominantly at the beginning of the season while the untended M. tanacetaria produced winged individuals throughout the season. Winged mothers of both species produced winged offspring, although in both species winged offspring were mainly produced by unwinged females. Crowding and the presence of predators, effects already known to influence wing production in other aphid species, increased the percentage of winged offspring in M. tanacetaria, but not in M. fuscoviride. We find there are also other factors (i.e. temporal effects inducing the production of winged offspring for natural aphid populations. Our results show that the responses of each aphid species are due to multiple wing induction cues.

  16. Mimicking unfolding motion of a beetle hind wing

    Institute of Scientific and Technical Information of China (English)

    MUHAMMAD Azhar; PARK Hoon C; HWANG Do Y; BYUN Doyoung; GOO Nam S

    2009-01-01

    This paper presents an experimental research aiming to realize an artificial hind wing that can mimic the wing unfolding motion of Allomyrina dichotoma, an insect in coleopteran order. Based on the understanding of working principles of beetle wing folding/unfolding mechanisms, the hind wing unfolding motion is mimicked by a combination of creative ideas and state-of-art artificial muscle actuator. In this work, we devise two types of artificial wings and the successfully demonstrate that they can be unfolded by actuation of shape memory alloy wires to provide actuation force at the wing base and along the leading edge vein. The folding/unfolding mechanisms may provide an insight for portable nano/micro air vehicles with morphing wings.

  17. Preliminary study of effects of winglets on wing flutter

    Science.gov (United States)

    Doggett, R. V., Jr.; Farmer, M. G.

    1976-01-01

    Some experimental flutter results are presented over a Mach number range from about 0.70 to 0.95 for a simple, swept, tapered, flat-plate wing model having a planform representative of subsonic transport airplanes and for the same wing model equipped with two different upper surface winglets. Both winglets had the same planform and area (about 2 percent of the basic-wing area); however, one weighed about 0.3 percent of the basic-wing weight, and the other weighed about 1.8 percent of the wing weight. The addition of the lighter winglet reduced the wing-flutter dynamic pressure by about 3 percent; the heavier winglet reduced the wing-flutter dynamic pressure by about 12 percent. The experimental flutter results are compared at a Mach number of 0.80 with analytical flutter results obtained by using doublet-lattice and lifting-surface (kernel-function) unsteady aerodynamic theories.

  18. Aerodynamic derivatives for an oblique wing aircraft estimated from flight data by using a maximum likelihood technique

    Science.gov (United States)

    Maine, R. E.

    1978-01-01

    There are several practical problems in using current techniques with five degree of freedom equations to estimate the stability and control derivatives of oblique wing aircraft from flight data. A technique was developed to estimate these derivatives by separating the analysis of the longitudinal and lateral directional motion without neglecting cross coupling effects. Although previously applied to symmetrical aircraft, the technique was not expected to be adequate for oblique wing vehicles. The application of the technique to flight data from a remotely piloted oblique wing aircraft is described. The aircraft instrumentation and data processing were reviewed, with particular emphasis on the digital filtering of the data. A complete set of flight determined stability and control derivative estimates is presented and compared with predictions. The results demonstrated that the relatively simple approach developed was adequate to obtain high quality estimates of the aerodynamic derivatives of such aircraft.

  19. DARPA/AFRL/NASA Smart Wing Second Wind Tunnel Test Results

    Science.gov (United States)

    Scherer, L. B.; Martin, C. A.; West, M.; Florance, J. P.; Wieseman, C. D.; Burner, A. W.; Fleming, G. A.

    2001-01-01

    To quantify the benefits of smart materials and structures adaptive wing technology, Northrop Grumman Corp. (NGC) built and tested two 16% scale wind tunnel models (a conventional and a "smart" model) of a fighter/attack aircraft under the DARPA/AFRL/NASA Smart Materials and Structures Development - Smart Wing Phase 1. Performance gains quantified included increased pitching moment (C(sub M)), increased rolling moment (C(subl)) and improved pressure distribution. The benefits were obtained for hingeless, contoured trailing edge control surfaces with embedded shape memory alloy (SMA) wires and spanwise wing twist effected by SMA torque tube mechanisms, compared to conventional hinged control surfaces. This paper presents an overview of the results from the second wind tunnel test performed at the NASA Langley Research Center s (LaRC) 16ft Transonic Dynamic Tunnel (TDT) in June 1998. Successful results obtained were: 1) 5 degrees of spanwise twist and 8-12% increase in rolling moment utilizing a single SMA torque tube, 2) 12 degrees of deflection, and 10% increase in rolling moment due to hingeless, contoured aileron, and 3) demonstration of optical techniques for measuring spanwise twist and deflected shape.

  20. Effect of wing mass in free flight by a butterfly-like 3D flapping wing-body model

    Science.gov (United States)

    Suzuki, Kosuke; Okada, Iori; Yoshino, Masato

    2016-11-01

    The effect of wing mass in free flight of a flapping wing is investigated by numerical simulations based on an immersed boundary-lattice Boltzmann method. We consider a butterfly-like 3D flapping wing-model consisting of two square wings with uniform mass density connected by a rod-shaped body. We simulate free flights of the wing-body model with various mass ratios of the wing to the whole of the model. As a result, it is found that the lift and thrust forces decrease as the mass ratio increases, since the body with a large mass ratio experiences large vertical and horizontal oscillations in one period and consequently the wing tip speed relatively decreases. In addition, we find the critical mass ratio between upward flight and downward flight for various Reynolds numbers. This work was supported by JSPS KAKENHI Grant Number JP16K18012.

  1. Rhodnius prolixus and Rhodnius robustus - like (Hemiptera, Reduviidae) wing asymmetry under controlled conditions of population density and feeding frequency

    Indian Academy of Sciences (India)

    E J Màrquez; C I Saldamando-Benjumea

    2013-09-01

    Habitat change in Rhodnius spp may represent an environmental challenge for the development of the species, particularly when feeding frequency and population density vary in nature. To estimate the effect of these variables in stability on development, the degree of directional asymmetry (DA) and fluctuating asymmetry (FA) in the wing size and shape of R. prolixus and R. robustus–like were measured under laboratory controlled conditions. DA and FA in wing size and shape were significant in both species, but their variation patterns showed both inter-specific and sexual dimorphic differences in FA of wing size and shape induced by nutrition stress. These results suggest different abilities of the genotypes and sexes of two sylvatic and domestic genotypes of Rhodnius to buffer these stress conditions. However, both species showed non-significant differences in the levels of FA between treatments that simulated sylvan vs domestic conditions, indicating that the developmental noise did not explain the variation in wing size and shape found in previous studies. Thus, this result confirm that the variation in wing size and shape in response to treatments constitute a plastic response of these genotypes to population density and feeding frequency.

  2. Efficient parallel implicit methods for rotary-wing aerodynamics calculations

    Science.gov (United States)

    Wissink, Andrew M.

    Euler/Navier-Stokes Computational Fluid Dynamics (CFD) methods are commonly used for prediction of the aerodynamics and aeroacoustics of modern rotary-wing aircraft. However, their widespread application to large complex problems is limited lack of adequate computing power. Parallel processing offers the potential for dramatic increases in computing power, but most conventional implicit solution methods are inefficient in parallel and new techniques must be adopted to realize its potential. This work proposes alternative implicit schemes for Euler/Navier-Stokes rotary-wing calculations which are robust and efficient in parallel. The first part of this work proposes an efficient parallelizable modification of the Lower Upper-Symmetric Gauss Seidel (LU-SGS) implicit operator used in the well-known Transonic Unsteady Rotor Navier Stokes (TURNS) code. The new hybrid LU-SGS scheme couples a point-relaxation approach of the Data Parallel-Lower Upper Relaxation (DP-LUR) algorithm for inter-processor communication with the Symmetric Gauss Seidel algorithm of LU-SGS for on-processor computations. With the modified operator, TURNS is implemented in parallel using Message Passing Interface (MPI) for communication. Numerical performance and parallel efficiency are evaluated on the IBM SP2 and Thinking Machines CM-5 multi-processors for a variety of steady-state and unsteady test cases. The hybrid LU-SGS scheme maintains the numerical performance of the original LU-SGS algorithm in all cases and shows a good degree of parallel efficiency. It experiences a higher degree of robustness than DP-LUR for third-order upwind solutions. The second part of this work examines use of Krylov subspace iterative solvers for the nonlinear CFD solutions. The hybrid LU-SGS scheme is used as a parallelizable preconditioner. Two iterative methods are tested, Generalized Minimum Residual (GMRES) and Orthogonal s-Step Generalized Conjugate Residual (OSGCR). The Newton method demonstrates good

  3. Integration effects of pylon geometry and rearward mounted nacelles for a high-wing transport

    Science.gov (United States)

    Carlson, John R.; Lamb, Milton

    1987-01-01

    Results of a wind-tunnel study of the effect of pylon cross-sectional shape and tow angle on airplane drag and an aft-mounted nacelle are presented. The 1/24-scale wide-body high-wing transport model was tested in the Langley 16-Foot Transonic Tunnel at free-stream Mach 0.7-0.8 and angles of attack from -3 to 4 degrees. A compression-type pylon is found to have the lowest drag at both Mach 0.7 and 0.8 and to be capable of suppressing the velocities in the inboard region of the pylon-wing junction, reducing the extent of supersonic flow and the probability of flow separation. It is also shown that the D-shaped aft-mounted nacelle has a low interference drag, as do previously tested circular nacelles in the same position.

  4. Effects of Dragonfly Wing Structure on the Dynamic Performances

    Institute of Scientific and Technical Information of China (English)

    Huaihui Ren; Xishu Wang; Xudong Li; Yinglong Chen

    2013-01-01

    The configurations of dragonfly wings,including the corrugations of the chordwise cross-section,the microstructure of the longitudinal veins and membrane,were comprehensively investigated using the Environmental Scanning Electron Microscopy (ESEM).Based on the experimental results reported previously,the multi-scale and multi-dimensional models with different structural features of dragonfly wing were created,and the biological dynamic behaviors of wing models were discussed through the Finite Element Method (FEM).The results demonstrate that the effects of different structural features on dynamic behaviors of dragonfly wing such as natural frequency/modal,bending/torsional deformation,reaction force/torque are very significant.The corrugations of dragonfly wing along the chordwise can observably improve the flapping frequency because of the greater structural stiffness of wings.In updated model,the novel sandwich microstructure of the longitudinal veins remarkably improves the torsional deformation of dragonfly wing while it has a little effect on the flapping frequency and bending deformation.These integrated structural features can adjust the deformation of wing oneself,therefore the flow field around the wings can be controlled adaptively.The fact is that the flights of dragonfly wing with sandwich microstructure of longitudinal veins are more efficient and intelligent.

  5. Interceptive management of winged maxillary central incisors

    Directory of Open Access Journals (Sweden)

    Mamta Dali

    2013-01-01

    Full Text Available Introduction: Winged maxillary incisors are a well-recognized clinical finding, which can result in psychological trauma to children at growing age. Interceptive treatment is usually carried out in mixed dentition period in order to reduce the severity of a developing malocclusion in future. Case Report: This paper reports a case of 6-years-old female patient with winged maxillary central incisor being treated with derotation technique using the beggs brackets along with nance palatal arch space maintainer. Discussion: The major advantages in carrying out this treatment with fixed brackets are the ease with which the force magnitude and vector can be controlled much more precisely than with a removable appliance, minimal discomfort to the patient and reduces the need for patient co-operation.

  6. The Crest Wing Wave Energy Device

    DEFF Research Database (Denmark)

    Kofoed, Jens Peter; Antonishen, Michael Patrick

    This report presents the results of a continuation of an experimental study of the wave energy converting abilities of the Crest Wing wave energy converter (WEC), in the following referred to as ‘Phase 2'. The Crest Wing is a WEC that uses its movement in matching the shape of an oncoming wave...... to generate power. Model tests have been performed using scale models (length scale 1:30), provided by WaveEnergyFyn, in regular and irregular wave states that can be found in Assessment of Wave Energy Devices. Best Practice as used in Denmark (Frigaard et al., 2008). The tests were carried out at Dept....... of Civil Engineering, Aalborg University (AAU) in the 3D deep water wave tank. The displacement and force applied to a power take off system, provided by WaveEnergyFyn, were measured and used to calculate mechanical power available to the power take off....

  7. Charge Capacity of Piezoelectric Membrane Wings

    Science.gov (United States)

    Grybas, Matthew; Hubner, J. Paul

    2015-11-01

    Micro air vehicles (MAVs) have small wings often fabricated with flexible frames and membranes. These membranes flex and vibrate. Piezoelectric films have the ability to convert induced stress or strain into electrical energy. Thus, it is of interest to investigate if piezoelectric films can be used as a structural member of an MAV wing and generate both lift and energy through passive vibrations. Both a shaker test and a wind tunnel test have been conducted to characterize and assess energy production and aerodynamic characteristics including lift, drag and efficiency. The piezoelectric film has been successful as a lifting surface and produces a measurable charge. This work was supported by NSF REU Site Award 1358991.

  8. WOODEN DOOR WINGS OF ADIYAMAN GREAT MOSQUE

    Directory of Open Access Journals (Sweden)

    Muhammet ARSLAN

    2010-06-01

    Full Text Available Woodworking which is in the most important Turk art branches have been used especially in Anatolia land readily. Wooden material that is seen on architectural units such as mimbar, ambo, wings of door and window, lectern has an important particularly with its ornamental figures. Wooden composition on the north and east doors of Adıyaman Great Mosque was built by Dulkadir Principality but regulated again in the last period of Ottoman Empire, is a theme which is exemined detailedly in Turk art. In this article, it is tried to determined ornamentel and tecnical characteristics of wooden door wings of Adıyaman Great Mosque belongs to early XX. century and the place of them in Turk art.

  9. Origin and diversification of wings: Insights from a neopteran insect.

    Science.gov (United States)

    Medved, Victor; Marden, James H; Fescemyer, Howard W; Der, Joshua P; Liu, Jin; Mahfooz, Najmus; Popadić, Aleksandar

    2015-12-29

    Winged insects underwent an unparalleled evolutionary radiation, but mechanisms underlying the origin and diversification of wings in basal insects are sparsely known compared with more derived holometabolous insects. In the neopteran species Oncopeltus fasciatus, we manipulated wing specification genes and used RNA-seq to obtain both functional and genomic perspectives. Combined with previous studies, our results suggest the following key steps in wing origin and diversification. First, a set of dorsally derived outgrowths evolved along a number of body segments including the first thoracic segment (T1). Homeotic genes were subsequently co-opted to suppress growth of some dorsal flaps in the thorax and abdomen. In T1 this suppression was accomplished by Sex combs reduced, that when experimentally removed, results in an ectopic T1 flap similar to prothoracic winglets present in fossil hemipteroids and other early insects. Global gene-expression differences in ectopic T1 vs. T2/T3 wings suggest that the transition from flaps to wings required ventrally originating cells, homologous with those in ancestral arthropod gill flaps/epipods, to migrate dorsally and fuse with the dorsal flap tissue thereby bringing new functional gene networks; these presumably enabled the T2/T3 wing's increased size and functionality. Third, "fused" wings became both the wing blade and surrounding regions of the dorsal thorax cuticle, providing tissue for subsequent modifications including wing folding and the fit of folded wings. Finally, Ultrabithorax was co-opted to uncouple the morphology of T2 and T3 wings and to act as a general modifier of hindwings, which in turn governed the subsequent diversification of lineage-specific wing forms.

  10. CFD Analysis of UAV Flying Wing

    Directory of Open Access Journals (Sweden)

    Vasile PRISACARIU

    2016-09-01

    Full Text Available Numerical methods for solving equations describing the evolution of 3D fluid experienced a significant development closely related to the progress of information systems. Today, especially in the field of fluid mechanics, numerical simulations allow the study of gas-thermodynamic confirmed by experimental techniques in wind tunnel conditions and actual flight tests for modeling complex aircraft. The article shows a case of numerical analysis of the lifting surface on the UAV type flying wing.

  11. X-38 on B-52 Wing Pylon

    Science.gov (United States)

    1997-01-01

    A unique, close-up view of the X-38 (Crew Return Vehicle) under the wing of NASA's B-52 mothership prior to launch of the lifting-body research vehicle. The photo was taken from the observation window of the B-52 bomber as it banked in flight. The X-38 Crew Return Vehicle (CRV) research project is designed to develop the technology for a prototype emergency crew return vehicle or lifeboat for the International Space Station.

  12. Maintenance cost study of rotary wing aircraft

    Science.gov (United States)

    1977-01-01

    The feasibility was studied of predicting rotary wing operation maintenance costs by using several aircraft design factors for the aircraft dynamic systems. The dynamic systems considered were engines, drives and transmissions, rotors, and flight controls. Multiple regression analysis was used to correlate aircraft design and operational factors with manhours per flight hour, and equations for each dynamic system were developed. Results of labor predictions using the equations compare favorably with actual values.

  13. Autonomous Deicing System For Airplane Wing

    Science.gov (United States)

    Hickman, G. A.; Gerardi, J. J.

    1993-01-01

    Prototype autonomous deicing system for airplane includes network of electronic and electromechanical modules at various locations in wings and connected to central data-processing unit. Small, integrated solid-state device, using long coils installed under leading edge, exciting small vibrations to detect ice and larger vibrations to knock ice off. In extension of concept, outputs of vibration sensors and other sensors used to detect rivet-line fractures, fatigue cracks, and other potentially dangerous defects.

  14. Mother Nature inspires new wind turbine wing

    DEFF Research Database (Denmark)

    Sønderberg Petersen, L.

    2007-01-01

    The sight of a bird of prey hanging immobile in the air while its wings continuously adjust themselves slightly in relation to the wind in order to keep the bird in the same position in the air, is a sight that most of us have admired, including the windenergy scientists at Risø DTU. They have st...... started transferring the principle to wind turbine blades to make them adaptive...

  15. Functional analysis of genes differentially expressed in the Drosophila wing disc: role of transcripts enriched in the wing region.

    Science.gov (United States)

    Jacobsen, Thomas L; Cain, Donna; Paul, Litty; Justiniano, Steven; Alli, Anwar; Mullins, Jeremi S; Wang, Chun Ping; Butchar, Jon P; Simcox, Amanda

    2006-12-01

    Differential gene expression is the major mechanism underlying the development of specific body regions. Here we assessed the role of genes differentially expressed in the Drosophila wing imaginal disc, which gives rise to two distinct adult structures: the body wall and the wing. Reverse genetics was used to test the function of uncharacterized genes first identified in a microarray screen as having high levels of expression in the presumptive wing. Such genes could participate in elaborating the specific morphological characteristics of the wing. The activity of the genes was modulated using misexpression and RNAi-mediated silencing. Misexpression of eight of nine genes tested caused phenotypes. Of 12 genes tested, 10 showed effective silencing with RNAi transgenes, but only 3 of these had resulting phenotypes. The wing phenotypes resulting from RNAi suggest that CG8780 is involved in patterning the veins in the proximal region of the wing blade and that CG17278 and CG30069 are required for adhesion of wing surfaces. Venation and apposition of the wing surfaces are processes specific to wing development providing a correlation between the expression and function of these genes. The results show that a combination of expression profiling and tissue-specific gene silencing has the potential to identify new genes involved in wing development and hence to contribute to our understanding of this process. However, there are both technical and biological limitations to this approach, including the efficacy of RNAi and the role that gene redundancy may play in masking phenotypes.

  16. The effects of corrugation and wing planform on the aerodynamic force production of sweeping model insect wings

    Institute of Scientific and Technical Information of China (English)

    Guoyu Luo; Mao Sun

    2005-01-01

    The effects of corrugation and wing planform (shape and aspect ratio) on the aerodynamic force production of model insect wings in sweeping (rotating after an initial start) motion at Reynolds number 200 and 3500 at angle of attack 40° are investigated, using the method of computational fluid dynamics. A representative wing corrugation is considered. Wing-shape and aspect ratio (AR) of ten representative insect wings are considered; they are the wings of fruit fly, cranefly, dronefly, hoverfly, ladybird, bumblebee, honeybee, lacewing (forewing), hawkmoth and dragonfly (forewing), respectively (AR of these wings varies greatly,from 2.84 to 5.45). The following facts are shown.(1) The corrugated and flat-plate wings produce approximately the same aerodynamic forces. This is because for a sweeping wing at large angle of attack, the length scale of the corrugation is much smaller than the size of the separated flow region or the size of the leading edge vortex (LEV). (2) The variation in wing shape can have considerable effects on the aerodynamic force; but it has only minor effects on the force coefficients when the velocity at r2 (the radius of the second moment of wing area) is used as the reference velocity; i.e.the force coefficients are almost unaffected by the variation in wing shape. (3) The effects of AR are remarkably small:when AR increases from 2.8 to 5.5, the force coefficients vary only slightly; flowfield results show that when AR is relatively large, the part of the LEV on the outer part of the wings sheds during the sweeping motion. As AR is increased, on one hand,the force coefficients will be increased due to the reduction of 3-dimensional flow effects; on the other hand, they will be decreased due to the shedding of pan of the LEV; these two effects approximately cancel each other, resulting in only minor change of the force coefficients.

  17. When Graduate Degrees Prostitute the Educational Process: Degrees Gone Wild

    Science.gov (United States)

    Lumadue, Richard T.

    2006-01-01

    Graduate degrees prostitute the educational process when they are sold to consumers by unaccredited degree/diploma mills as being equivalent to legitimate, bona-fide degrees awarded by accredited graduate schools. This article carefully analyzes the serious problems of bogus degrees and their association with the religious higher education…

  18. Analysis and Flexible Structural Modeling for Oscillating Wing Utilizing Aeroelasticity

    Institute of Scientific and Technical Information of China (English)

    Shao Ke; Wu Zhigang; Yang Chao

    2008-01-01

    Making use of modal characteristics of the natural vibration of flexible structure to design the oscillating wing aircraft is proposed.A series of equations concerning the oscillating wing of flexible structures are derived. The kinetic equation for aerodynamic force coupled with elastic movement is set up, and relevant formulae are derived. The unsteady aerodynamic one in that formulae is revised. The design principle, design process and range of application of such oscillating wing analytical method are elaborated. A flexible structural oscillating wing model is set up, and relevant time response analysis and frequency response analysis are conducted. The analytical results indicate that adopting the new-type driving way for the oscillating wing will not have flutter problems and will be able to produce propulsive force. Furthermore, it will consume much less power than the fixed wing for generating the same lift.

  19. Fiber Optic Wing Shape Sensing on NASA's Ikhana UAV

    Science.gov (United States)

    Richards, Lance; Parker, Allen R.; Ko, William L.; Piazza, Anthony

    2008-01-01

    This document discusses the development of fiber optic wing shape sensing on NASA's Ikhana vehicle. The Dryden Flight Research Center's Aerostructures Branch initiated fiber-optic instrumentation development efforts in the mid-1990s. Motivated by a failure to control wing dihedral resulting in a mishap with the Helios aircraft, new wing displacement techniques were developed. Research objectives for Ikhana included validating fiber optic sensor measurements and real-time wing shape sensing predictions; the validation of fiber optic mathematical models and design tools; assessing technical viability and, if applicable, developing methodology and approaches to incorporate wing shape measurements within the vehicle flight control system; and, developing and flight validating approaches to perform active wing shape control using conventional control surfaces and active material concepts.

  20. Compound Wing Vertical Takeoff and Landing Small Unmanned Aircraft System

    Science.gov (United States)

    Logan, Michael J. (Inventor); Motter, Mark A. (Inventor); Deloach, Richard (Inventor); Vranas, Thomas L. (Inventor); Prendergast, Joseph M. (Inventor); Lipp, Brittney N. (Inventor)

    2017-01-01

    Systems, methods, and devices are provided that enable robust operations of a small unmanned aircraft system (sUAS) using a compound wing. The various embodiments may provide a sUAS with vertical takeoff and landing capability, long endurance, and the capability to operate in adverse environmental conditions. In the various embodiments a sUAS may include a fuselage and a compound wing comprising a fixed portion coupled to the fuselage, a wing lifting portion outboard of the fixed portion comprising a rigid cross member and a controllable articulating portion configured to rotate controllable through a range of motion from a horizontal position to a vertical position, and a freely rotating wing portion outboard of the wing lifting portion and configured to rotate freely based on wind forces incident on the freely rotating wing portion.

  1. Video measurements of instantaneous forces of flapping wing vehicles

    Science.gov (United States)

    Jennings, Alan; Mayhew, Michael; Black, Jonathan

    2015-12-01

    Flapping wings for small aerial vehicles have revolutionary potential for maneuverability and endurance. Ornithopters fail to achieve the performance of their biological equivalents, despite extensive research on how animals fly. Flapping wings produce peak forces due to the stroke reversal of the wing. This research demonstrates in-flight measurements of an ornithopter through the use of image processing, specifically measuring instantaneous forces. Results show that the oscillation about the flight path is significant, being about 20% of the mean velocity and up to 10 g's. Results match forces with deformations of the wing to contrast the timing and wing shape of the upstroke and the downstroke. Holding the vehicle fixed (e.g. wind tunnel testing or simulations) structural resonance is affected along with peak forces, also affecting lift. Non-contact, in-flight measurements are proposed as the best method for matching the flight conditions of flapping wing vehicles.

  2. Vortex Interaction on Low Aspect Ratio Membrane Wings

    Science.gov (United States)

    Waldman, Rye M.; Breuer, Kenneth S.

    2013-11-01

    Inspired by the flight of bats and by recent interest in Micro Air Vehicles, we present measurements on the steady and unsteady behavior of low aspect ratio membrane wings. We conduct wind tunnel experiments with coupled force, kinematic, and flow field measurements, both on the wing and in the near wake. Membrane wings interact strongly with the vortices shed from the leading- and trailing-edges and the wing tips, and the details of the membrane support play an important role in the fluid-structure interaction. Membranes that are supported at the wing tip exhibit less membrane flutter, more coherent tip vortices, and enhanced lift. The interior wake can exhibit organized spanwise vortex shedding, and shows little influence from the tip vortex. In contrast, membranes with an unsupported wing tip show exaggerated static deformation, significant membrane fluttering and a diffuse, unsteady tip vortex. The unsteady tip vortex modifies the behavior of the interior wake, disrupting the wake coherence.

  3. Simplifying a wing: diversity and functional consequences of digital joint reduction in bat wings.

    Science.gov (United States)

    Bahlman, Joseph W; Price-Waldman, Rosalyn M; Lippe, Hannah W; Breuer, Kenneth S; Swartz, Sharon M

    2016-07-01

    Bat wings, like other mammalian forelimbs, contain many joints within the digits. These joints collectively affect dynamic three-dimensional (3D) wing shape, thereby affecting the amount of aerodynamic force a wing can generate. Bats are a speciose group, and show substantial variation in the number of wing joints. Additionally, some bat species have joints with extensor but no flexor muscles. While several studies have examined the diversity in number of joints and presence of muscles, musculoskeletal variation in the digits has not been interpreted in phylogenetic, functional or ecological contexts. To provide this context, the number of joints and the presence/absence of muscles are quantified for 44 bat species, and are mapped phylogenetically. It is shown that, relative to the ancestral state, joints and muscles were lost multiple times from different digits and in many lineages. It is also shown that joints lacking flexors undergo cyclical flexion and extension, in a manner similar to that observed in joints with both flexors and extensors. Comparison of species with contrasting feeding ecologies demonstrates that species that feed primarily on non-mobile food (e.g. fruit) have fewer fully active joints than species that catch mobile prey (e.g. insects). It is hypothesized that there is a functional trade-off between energetic savings and maneuverability. Having fewer joints and muscles reduces the mass of the wing, thereby reducing the energetic requirements of flapping flight, and having more joints increases the assortment of possible 3D wing shapes, thereby enhancing the range and fine control of aerodynamic force production and thus maneuverability.

  4. Incompressible Turbulent Wing-Body Junction Flow

    Science.gov (United States)

    Krishnamurthy, R.; Cagle, Corey D.; Chandra, S.

    1998-01-01

    The overall objective of this study is to contribute to the optimized design of fan bypass systems in advanced turbofan engines. Increasing the engine bypass ratios have provided a major boost in engine performance improvement over the last fifty years. An engine with high bypass ratio (11-16:1) such as the Advanced Ducted Propulsion (ADP) is being developed and is expected to provide an additional 25% improvement in overall efficiency over the early turbofans. Such significant improvements in overall efficiency would reduce the cost per seat mile, which is a major government and Industry challenge for the 21th century. The research is part of the Advanced Subsonic Technology (AST) program that involves a NASA, U.S. Industry and FAA partnership with the goal of a safe and highly productive global air transportation system. The immediate objective of the study is to perform numerical simulation of duct-strut interactions to elucidate the loss mechanisms associated with this configuration that is typical of advanced turbofan engines such as ADP. However, at present experimental data for a duct-strut configuration are not available. Thus, as a first step a wing-body junction flow would be studied and is the specific objective of the present study. At the outset it is to be recognized that while duct-strut interaction flow is similar to that of wing-body junction flows, there are some differences owing to the presence of a wall at both ends of the strut. Likewise, some differences are due to the sheared inflow (as opposed to a uniform inflow) velocity profile. It is however expected that some features of a wing-body junction flow would persist. Next, some of the salient aspects of the complex flow near a wing-body junction, as revealed by various studies reported in the literature will be reviewed. One of the principle characteristics of the juncture flow, is the presence of the mean flow components in a plane perpendicular to the direction of the oncoming free

  5. Winging of scapula due to serratus anterior tear

    Institute of Scientific and Technical Information of China (English)

    Varun Kumar Singh; Gauresh Shantaram Vargaonkar

    2014-01-01

    Winging of scapula occurs most commonly due to injury to long thoracic nerve supplying serratus anterior muscle.Traumatic injury to serratus anterior muscle itself is very rare.We reported a case of traumatic winging of scapula due to tear of serratus anterior muscle in a 19-year-old male.Winging was present in neutral position and in extension of right shoulder joint but not on "push on wall" test.Patient was managed conservatively and achieved satisfactory result.

  6. The aerodynamic and structural study of flapping wing vehicles

    OpenAIRE

    2013-01-01

    This thesis reports on the aerodynamic and structural study carried out on flapping wings and flapping vehicles. Theoretical and experimental investigation of aerodynamic forces acting on flapping wings in simple harmonic oscillations is undertaken in order to help conduct and optimize the aerodynamic and structural design of flapping wing vehicles. The research is focused on the large scale ornithopter design of similar size and configuration to a hang glider. By means of Theodorsen’s th...

  7. Wing shape of dengue vectors from around the world

    OpenAIRE

    Henry, A; Thongsripong, P.; Fonseca-Gonzalez, I.; Jaramillo-Ocampo, N.; Dujardin, Jean-Pierre

    2010-01-01

    Wing shape is increasingly utilized in species identification and characterization. For dengue vectors Aedes aegypti and Aedes albopictus, it could be used as a complement for ensuring accurate diagnostic of damaged specimens. However, the impact of world migration on wing shape is unknown. Has the spread of these invasive species increased shape variation to the extent of producing interspecific overlapping? To answer this question, the geometric patterns of wing venation in Ae. aegypti and ...

  8. Investigation and design of a C-Wing passenger aircraft

    Directory of Open Access Journals (Sweden)

    Karan BIKKANNAVAR

    2016-06-01

    Full Text Available A novel nonplanar wing concept called C-Wing is studied and implemented on a commercial aircraft to reduce induced drag which has a significant effect on fuel consumption. A preliminary sizing method which employs an optimization algorithm is utilized. The Airbus A320 aircraft is used as a reference aircraft to evaluate design parameters and to investigate the C-Wing design potential beyond current wing tip designs. An increase in aspect ratio due to wing area reduction at 36m span results in a reduction of required fuel mass by 16%. Also take-off mass savings were obtained for the aircraft with C-Wing configuration. The effect of a variations of height to span ratio (h/b of C-Wings on induced drag factor k, is formulated from a vortex lattice method and literature based equations. Finally the DOC costing methods used by the Association of European Airlines (AEA was applied to the existing A320 aircraft and to the C-Wing configuration obtaining a reduction of 6% in Direct Operating Costs (DOC for the novel concept resulted. From overall outcomes, the C-Wing concept suggests interesting aerodynamic efficiency and stability benefits.

  9. Technicians prepare the inflatable wing on Paresev 1-C

    Science.gov (United States)

    1963-01-01

    This photo shows the Paresev (Paraglider Research Vehicle) space frame receiving a new wing. Frank Fedor and a technician helper are attaching a half-scale version of an inflatable wing in a hangar at NASA Flight Research Center at Edwards, California. The Paresev in this configuration was called the 1-C and was expected to closely approximate the aerodynamic characteristics that would be encountered with the Gemini space capsule with a parawing extended. The whole wing was not inflatable; the three chambers that acted as spars and supported the wing inflated.

  10. Aeroelastic Deformation and Buckling of Inflatable Wings under Dynamic Loads

    Science.gov (United States)

    Simpson, Andrew; Smith, Suzanne; Jacob, Jamey

    2006-11-01

    Inflatable wings have recently been used to control a vehicle in flight via wing warping. Internal pressure is required to maintain wing shape and externally mounted mechanical actuators are used to asynchronously deform the wing semi-spans for control. Since the rigidity of the inflatable wing varies as a function of inflation pressure, there is a need to relate the wing shape with aerodynamic loads. Via wind tunnel tests, span-wise deformations, twist and flutter have been observed under certain dynamic loading conditions. Photogrammetry techniques are used to measure the static aeroelastic deformation of the wings and videogrammetry is used to examine the dynamic shape changes (flutter). The resulting shapes can be used to determine corresponding aerodynamic characteristics. For particular inflation pressures, buckling can be induced at sufficiently high dynamic loads either through high dynamic pressure or large angle of attack. This results in a set of critical loading parameters. An inflatable winged vehicle would require operation within these limits. The focus of the presentation will be on defining and exploring the unsuitable operating conditions and the effects these conditions have on the operation of the wing.

  11. Embedded Fiber Optic Shape Sensing for Aeroelastic Wing Components Project

    Data.gov (United States)

    National Aeronautics and Space Administration — As the aerospace industry continues to push for greater vehicle efficiency, performance, and longevity, properties of wing aeroelasticity and flight dynamics have...

  12. Design, Fabrication and Testing Of Flapping Wing Micro Air Vehicle

    Directory of Open Access Journals (Sweden)

    K. P. Preethi Manohari Sai

    2016-01-01

    Full Text Available Flapping flight has the potential to revolutionize micro air vehicles (MAVs due to increased aerodynamic performance, improved maneuverability and hover capabilities. The purpose of this project is to design and fabrication of flapping wing micro air vehicle. The designed MAV will have a wing span of 40cm. The drive mechanism will be a gear mechanism to drive the flapping wing MAV, along with one actuator. Initially, a preliminary design of flapping wing MAV is drawn and necessary calculation for the lift calculation has been done. Later a CAD model is drawn in CATIA V5 software. Finally we tested by Flying.

  13. MEMS wing technology for a battery-powered ornithopter

    OpenAIRE

    2000-01-01

    The objective of this project is to develop a battery-powered ornithopter (flapping-wing) Micro Aerial Vehicle (MAV) with MEMS wings. In this paper, we present a novel MEMS-based wing technology that we developed using titanium-alloy metal as wingframe and parylene C as wing membrane. MEMS technology enables systematic research in terms of repeatablility, size control, and weight minimization. We constructed a high quality low-speed wind tunnel with velocity uniformity of 0.5% and speeds from...

  14. Feedback Linearization Controller Of The Delta WingRock Phenomena

    Directory of Open Access Journals (Sweden)

    Mohammed Alkandari

    2015-05-01

    Full Text Available This project deals with the control of the wing rock phenomena of a delta wing aircraft. a control schemeis proposed to stabilize the system. The controlleris a feedback linearization controller. It is shown that the proposed control scheme guarantee the asymptotic convergence to zero of all the states of the system. To illustrate the performance of the proposed controller, simulation results are presented and discussed. It is found that the proposed control scheme work well for the wing rock phenomena of a delta wing aircraft.

  15. Experimental investigations of the functional morphology of dragonfly wings

    Institute of Scientific and Technical Information of China (English)

    H.Rajabi; A.Darvizeh

    2013-01-01

    Nowadays,the importance of identifying the flight mechanisms of the dragonfly,as an inspiration for designing flapping wing vehicles,is well known.An experimental approach to understanding the complexities of insect wings as organs of flight could provide significant outcomes for design purposes.In this paper,a comprehensive investigation is carried out on the morphological and microstructural features of dragonfly wings.Scanning electron microscopy (SEM) and tensile testing are used to experimentally verify the functional roles of different parts of the wings.A number of SEM images of the elements of the wings,such as the nodus,leading edge,trailing edge,and vein sections,which play dominant roles in strengthening the whole structure,are presented.The results from the tensile tests indicate that the nodus might be the critical region of the wing that is subjected to high tensile stresses.Considering the patterns of the longitudinal corrugations of the wings obtained in this paper,it can be supposed that they increase the load-bearing capacity,giving the wings an ability to tolerate dynamic loading conditions.In addition,it is suggested that the longitudinal veins,along with the leading and trailing edges,are structural mechanisms that further improve fatigue resistance by providing higher fracture toughness,preventing crack propagation,and allowing the wings to sustain a significant amount of damage without loss of strength.

  16. Complexity analyses of multi-wing chaotic systems

    Institute of Scientific and Technical Information of China (English)

    He Shao-Bo; Sun Ke-Hui; Zhu Cong-Xu

    2013-01-01

    The complexities of multi-wing chaotic systems based on the modified Chen system and a multi-segment quadratic function are investigated by employing the statistical complexity measure (SCM) and the spectral entropy (SE) algorithm.How to choose the parameters of the SCM and SE algorithms is discussed.The results show that the complexity of the multi-wing chaotic system does not increase as the number of wings increases,and it is consistent with the results of the Grassberger-Procaccia (GP) algorithm and the largest Lyapunov exponent (LLE) of the multi-wing chaotic system.

  17. Complexity analyses of multi-wing chaotic systems

    Science.gov (United States)

    He, Shao-Bo; Sun, Ke-Hui; Zhu, Cong-Xu

    2013-05-01

    The complexities of multi-wing chaotic systems based on the modified Chen system and a multi-segment quadratic function are investigated by employing the statistical complexity measure (SCM) and the spectral entropy (SE) algorithm. How to choose the parameters of the SCM and SE algorithms is discussed. The results show that the complexity of the multi-wing chaotic system does not increase as the number of wings increases, and it is consistent with the results of the Grassberger—Procaccia (GP) algorithm and the largest Lyapunov exponent (LLE) of the multi-wing chaotic system.

  18. Prediction of span loading of straight-wing/propeller combinations up to stall. [propeller slipstreams and wing loading

    Science.gov (United States)

    Mcveigh, M. A.; Gray, L.; Kisielowski, E.

    1975-01-01

    A method is presented for calculating the spanwise lift distribution on straight-wing/propeller combinations. The method combines a modified form of the Prandtl wing theory with a realistic representation of the propeller slipstream distribution. The slipstream analysis permits calculations of the nonuniform axial and rotational slipstream velocity field of propeller/nacelle combinations. This nonuniform field was then used to calculate the wing lift distribution by means of the modified Prandtl wing theory. The theory was developed for any number of nonoverlapping propellers, on a wing with partial or full-span flaps, and is applicable throughout an aspect ratio range from 2.0 and higher. A computer program was used to calculate slipstream characteristics and wing span load distributions for a number of configurations for which experimental data are available, and favorable comparisons are demonstrated between the theoretical predictions and the existing data.

  19. Folding wings like a cockroach: a review of transverse wing folding ensign wasps (Hymenoptera: Evaniidae: Afrevania and Trissevania.

    Directory of Open Access Journals (Sweden)

    István Mikó

    Full Text Available We revise two relatively rare ensign wasp genera, whose species are restricted to Sub-Saharan Africa: Afrevania and Trissevania. Afrevania longipetiolata sp. nov., Trissevania heatherae sp. nov., T. hugoi sp. nov., T. mrimaensis sp. nov. and T. slideri sp. nov. are described, males and females of T. anemotis and Afrevania leroyi are redescribed, and an identification key for Trissevaniini is provided. We argue that Trissevania mrimaensis sp. nov. and T. heatherae sp. nov. populations are vulnerable, given their limited distributions and threats from mining activities in Kenya. We hypothesize that these taxa together comprise a monophyletic lineage, Trissevaniini, tr. nov., the members of which share the ability to fold their fore wings along two intersecting fold lines. Although wing folding of this type has been described for the hind wing of some insects four-plane wing folding of the fore wing has never been documented. The wing folding mechanism and the pattern of wing folds of Trissevaniini is shared only with some cockroach species (Blattodea. It is an interesting coincidence that all evaniids are predators of cockroach eggs. The major wing fold lines of Trissevaniini likely are not homologous to any known longitudinal anatomical structures on the wings of other Evaniidae. Members of the new tribe share the presence of a coupling mechanism between the fore wing and the mesosoma that is composed of a setal patch on the mesosoma and the retinaculum of the fore wing. While the setal patch is an evolutionary novelty, the retinaculum, which originally evolved to facilitate fore and hind wing coupling in Hymenoptera, exemplifies morphological exaptation. We also refine and clarify the Semantic Phenotype approach used in previous taxonomic revisions and explore the consequences of merging new with existing data. The way that semantic statements are formulated can evolve in parallel, alongside improvements to the ontologies themselves.

  20. Folding wings like a cockroach: a review of transverse wing folding ensign wasps (Hymenoptera: Evaniidae: Afrevania and Trissevania).

    Science.gov (United States)

    Mikó, István; Copeland, Robert S; Balhoff, James P; Yoder, Matthew J; Deans, Andrew R

    2014-01-01

    We revise two relatively rare ensign wasp genera, whose species are restricted to Sub-Saharan Africa: Afrevania and Trissevania. Afrevania longipetiolata sp. nov., Trissevania heatherae sp. nov., T. hugoi sp. nov., T. mrimaensis sp. nov. and T. slideri sp. nov. are described, males and females of T. anemotis and Afrevania leroyi are redescribed, and an identification key for Trissevaniini is provided. We argue that Trissevania mrimaensis sp. nov. and T. heatherae sp. nov. populations are vulnerable, given their limited distributions and threats from mining activities in Kenya. We hypothesize that these taxa together comprise a monophyletic lineage, Trissevaniini, tr. nov., the members of which share the ability to fold their fore wings along two intersecting fold lines. Although wing folding of this type has been described for the hind wing of some insects four-plane wing folding of the fore wing has never been documented. The wing folding mechanism and the pattern of wing folds of Trissevaniini is shared only with some cockroach species (Blattodea). It is an interesting coincidence that all evaniids are predators of cockroach eggs. The major wing fold lines of Trissevaniini likely are not homologous to any known longitudinal anatomical structures on the wings of other Evaniidae. Members of the new tribe share the presence of a coupling mechanism between the fore wing and the mesosoma that is composed of a setal patch on the mesosoma and the retinaculum of the fore wing. While the setal patch is an evolutionary novelty, the retinaculum, which originally evolved to facilitate fore and hind wing coupling in Hymenoptera, exemplifies morphological exaptation. We also refine and clarify the Semantic Phenotype approach used in previous taxonomic revisions and explore the consequences of merging new with existing data. The way that semantic statements are formulated can evolve in parallel, alongside improvements to the ontologies themselves.

  1. Basal Complex and Basal Venation of Odonata Wings: Structural Diversity and Potential Role in the Wing Deformation

    Science.gov (United States)

    Rajabi, H.; Ghoroubi, N.; Malaki, M.; Darvizeh, A.; Gorb, S. N.

    2016-01-01

    Dragonflies and damselflies, belonging to the order Odonata, are known to be excellent fliers with versatile flight capabilities. The ability to fly over a wide range of speeds, high manoeuvrability and great agility are a few characteristics of their flight. The architecture of the wings and their structural elements have been found to play a major role in this regard. However, the precise influence of individual wing components on the flight performance of these insects remains unknown. The design of the wing basis (so called basal complex) and the venation of this part are responsible for particular deformability and specific shape of the wing blade. However, the wing bases are rather different in representatives of different odonate groups. This presumably reflects the dimensions of the wings on one hand, and different flight characteristics on the other hand. In this article, we develop the first three-dimensional (3D) finite element (FE) models of the proximal part of the wings of typical representatives of five dragonflies and damselflies families. Using a combination of the basic material properties of insect cuticle, a linear elastic material model and a nonlinear geometric analysis, we simulate the mechanical behaviour of the wing bases. The results reveal that although both the basal venation and the basal complex influence the structural stiffness of the wings, it is only the latter which significantly affects their deformation patterns. The use of numerical simulations enabled us to address the role of various wing components such as the arculus, discoidal cell and triangle on the camber formation in flight. Our study further provides a detailed representation of the stress concentration in the models. The numerical analysis presented in this study is not only of importance for understanding structure-function relationship of insect wings, but also might help to improve the design of the wings for biomimetic micro-air vehicles (MAVs). PMID:27513753

  2. Design and simulation of ex-range gliding wing of high altitude air-launched autonomous underwater vehicles based on SIMULINK

    Institute of Scientific and Technical Information of China (English)

    Pan Changjun; Guo Yingqing

    2013-01-01

    High altitude air-launched autonomous underwater vehicle (AL-AUV) is a new anti-submarine field,which is designed on the Lockheed Martin's high altitude anti-submarine warfare weapons concept (HAAWC) and conducts the basic aerodynamic feasibility in a series of wind tunnel trials.The AL-AUV is composed of a traditional torpedo-like AUV,an additional ex-range gliding wings unit and a descending parachute unit.In order to accurately and conveniently investigate the dynamic and static characteristic of high altitude AL-AUV,a simulation platform is established based on MATLAB/SIMULINK and an AUV 6DOF (Degree of Freedom) dynamic model.Executing the simulation platform for different wing's parameters and initial fixing angle,a set of AUV gliding data is generated.Analyzing the recorded simulation result,the velocity and pitch characteristics of AL-AUV deployed at varying wing areas and initial setting angle,the optimal wing area is selected for specific AUV model.Then the comparative simulations of AL-AUV with the selected wings are completed,which simulate the AUV gliding through idealized windless air environment and gliding with Dryden wind influence.The result indicates that the method of wing design and simulation with the simulation platform based on SIMULINK is accurately effective and suitable to be widely employed.

  3. Dynamics and control of robotic aircraft with articulated wings

    Science.gov (United States)

    Paranjape, Aditya Avinash

    There is a considerable interest in developing robotic aircraft, inspired by birds, for a variety of missions covering reconnaissance and surveillance. Flapping wing aircraft concepts have been put forth in light of the efficiency of flapping flight at small scales. These aircraft are naturally equipped with the ability to rotate their wings about the root, a form of wing articulation. This thesis covers some problems concerning the performance, stability and control of robotic aircraft with articulated wings in gliding flight. Specifically, we are interested in aircraft without a vertical tail, which would then use wing articulation for longitudinal as well as lateral-directional control. Although the dynamics and control of articulated wing aircraft share several common features with conventional fixed wing aircraft, the presence of wing articulation presents several unique benefits as well as limitations from the perspective of performance and control. One of the objective of this thesis is to understand these features using a combination of theoretical and numerical tools. The aircraft concept envisioned in this thesis uses the wing dihedral angles for longitudinal and lateral-directional control. Aircraft with flexible articulated wings are also investigated. We derive a complete nonlinear model of the flight dynamics incorporating dynamic CG location and the changing moment of inertia. We show that symmetric dihedral configuration, along with a conventional horizontal tail, can be used to control flight speed and flight path angle independently of each other. This characteristic is very useful for initiating an efficient perching maneuver. It is shown that wing dihedral angles alone can effectively regulate sideslip during rapid turns and generate a wide range of equilibrium turn rates while maintaining a constant flight speed and regulating sideslip. We compute the turning performance limitations that arise due to the use of wing dihedral for yaw control

  4. Numerical simulation of X-wing type biplane flapping wings in 3D using the immersed boundary method.

    Science.gov (United States)

    Tay, W B; van Oudheusden, B W; Bijl, H

    2014-09-01

    The numerical simulation of an insect-sized 'X-wing' type biplane flapping wing configuration is performed in 3D using an immersed boundary method solver at Reynolds numbers equal to 1000 (1 k) and 5 k, based on the wing's root chord length. This X-wing type flapping configuration draws its inspiration from Delfly, a bio-inspired ornithopter MAV which has two pairs of wings flapping in anti-phase in a biplane configuration. The objective of the present investigation is to assess the aerodynamic performance when the original Delfly flapping wing micro-aerial vehicle (FMAV) is reduced to the size of an insect. Results show that the X-wing configuration gives more than twice the average thrust compared with only flapping the upper pair of wings of the X-wing. However, the X-wing's average thrust is only 40% that of the upper wing flapping at twice the stroke angle. Despite this, the increased stability which results from the smaller lift and moment variation of the X-wing configuration makes it more suited for sharp image capture and recognition. These advantages make the X-wing configuration an attractive alternative design for insect-sized FMAVS compared to the single wing configuration. In the Reynolds number comparison, the vorticity iso-surface plot at a Reynolds number of 5 k revealed smaller, finer vortical structures compared to the simulation at 1 k, due to vortices' breakup. In comparison, the force output difference is much smaller between Re = 1 k and 5 k. Increasing the body inclination angle generates a uniform leading edge vortex instead of a conical one along the wingspan, giving higher lift. Understanding the force variation as the body inclination angle increases will allow FMAV designers to optimize the thrust and lift ratio for higher efficiency under different operational requirements. Lastly, increasing the spanwise flexibility of the wings increases the thrust slightly but decreases the efficiency. The thrust result is similar to one of the

  5. The energetic cost of variations in wing span and wing asymmetry in the zebra finch Taeniopygia guttata.

    Science.gov (United States)

    Hambly, C; Harper, E J; Speakman, J R

    2004-10-01

    Asymmetry is a difference in the sizes of bilaterally paired structures. Wing asymmetry may have an effect on the kinematics of flight, with knock-on effects for the energetic cost of flying. In this study the 13C-labelled bicarbonate technique was used to measure the energy expended during the flight of zebra finches Taeniopygia guttata, prior to and after experimental manipulation to generate asymmetry and a change in wing span by trimming the primary feathers. In addition, simultaneous high-speed video footage enabled differences in flight kinematics such as flight speed, wing amplitude, up- and downstroke duration and wing beat frequency to be examined. In 10 individuals, the primary feathers on the right wing were trimmed first, by 0.5 cm, and then by an additional 0.5 cm in six of these individuals. In a separate 'control' group (N=7), approximately 0.25 cm was trimmed off the primary feathers of both wings, to produce the same reduction in wing span as 0.5 cm trimmed from one wing, while maintaining symmetry. When birds were manipulated to become asymmetric they maintained flight speed. They also increased the left wing amplitude and decreased the right up- and downstroke durations to counteract the changes in wing shape, which meant that they had an increase in wing beat frequency. When the wing area was reduced while maintaining symmetry, birds flew with slower flight speed. In this case wing amplitude did not change and wing upstroke slightly decreased, causing an increased wing beat frequency. The mean flight cost in the pre-manipulated birds was 1.90+/-0.1 W. There was a slight increase in flight cost with both of the asymmetry manipulations (0.5 cm, increase of 0.04 W; 1.0 cm, increase of 0.12 W), neither of which reached statistical significance. There was, however, a significantly increased flight cost when the wing span was reduced without causing asymmetry (increase of 0.45 W; paired t-test T=2.3, P=0.03).

  6. An experimental study of tip shape effects on the flutter of aft-swept, flat-plate wings

    Science.gov (United States)

    Dansberry, Bryan E.; Rivera, Jose A., Jr.; Farmer, Moses G.

    1990-01-01

    The effects of tip chord orientation on wing flutter are investigated experimentally using six cantilever-mounted, flat-plate wing models. Experimentally determined flutter characteristics of the six models are presented covering both the subsonic and transonic Mach number ranges. While all models have a 60 degree leading edge sweep, a 40.97 degree trailing edge sweep, and a root chord of 34.75 inches, they are subdivided into two series characterized by a higher aspect ratio and a lower aspect ratio. Each series is made up of three models with tip chord orientations which are parallel to the free-stream flow, perpendicular to the model mid-chord line, and perpendicular to the free-stream flow. Although planform characteristics within each series of models are held constant, structural characteristics such as mode shapes and natural frequencies are allowed to vary.

  7. Wing Force & Moment Characterization of Flapping Wings for Micro Air Vehicle Application

    Science.gov (United States)

    2005-02-21

    is that position of the wing where φ = Φ0 as shown in Fig. 3(B). When Φ0 6= 0, the motion is called asymetric flapping. When Φ0 = 0, the motion is...For symmetric rotation, Ψ0 = 0, otherwise the motion is refered to as asymetric rotation. Angle of attack The angle of attack is the angle between

  8. Unsteady surface pressure measurements on a slender delta wing undergoing limit cycle wing rock

    Science.gov (United States)

    Arena, Andrew S., Jr.; Nelson, Robert C.

    1991-01-01

    An experimental investigation of slender wing limit cycle motion known as wing rock was investigated using two unique experimental systems. Dynamic roll moment measurements and visualization data on the leading edge vortices were obtained using a free to roll apparatus that incorporates an airbearing spindle. In addition, both static and unsteady surface pressure data was measured on the top and bottom surfaces of the model. To obtain the unsteady surface pressure data a new computer controller drive system was developed to accurately reproduce the free to roll time history motions. The data from these experiments include, roll angle time histories, vortex trajectory data on the position of the vortices relative to the model's surface, and surface pressure measurements as a function of roll angle when the model is stationary or undergoing a wing rock motion. The roll time history data was numerically differentiated to determine the dynamic roll moment coefficient. An analysis of these data revealed that the primary mechanism for the limit cycle behavior was a time lag in the position of the vortices normal to the wing surface.

  9. Repeatable Manufacture of Wings for Flapping Wing Micro Air Vehicles Using Microelectromechanical System (MEMS) Fabrication Techniques

    Science.gov (United States)

    2011-03-01

    104 A1.5 Dragonfly ......................................................................................................... 106 A1.6...in the size range being investigated include bats, swallows, hummingbirds, butterflies, beetles, dragonflies , and moths. A short synopsis of the...a MAV wing. Dragonflies are precise and controlled flyers, with the ability to hover and accelerate quickly, both from a dead stop as well as

  10. Optimization of composite tiltrotor wings with extensions and winglets

    Science.gov (United States)

    Kambampati, Sandilya

    Tiltrotors suffer from an aeroelastic instability during forward flight called whirl flutter. Whirl flutter is caused by the whirling motion of the rotor, characterized by highly coupled wing-rotor-pylon modes of vibration. Whirl flutter is a major obstacle for tiltrotors in achieving high-speed flight. The conventional approach to assure adequate whirl flutter stability margins for tiltrotors is to design the wings with high torsional stiffness, typically using 23% thickness-to-chord ratio wings. However, the large aerodynamic drag associated with these high thickness-to-chord ratio wings decreases aerodynamic efficiency and increases fuel consumption. Wingtip devices such as wing extensions and winglets have the potential to increase the whirl flutter characteristics and the aerodynamic efficiency of a tiltrotor. However, wing-tip devices can add more weight to the aircraft. In this study, multi-objective parametric and optimization methodologies for tiltrotor aircraft with wing extensions and winglets are investigated. The objectives are to maximize aircraft aerodynamic efficiency while minimizing weight penalty due to extensions and winglets, subject to whirl flutter constraints. An aeroelastic model that predicts the whirl flutter speed and a wing structural model that computes strength and weight of a composite wing are developed. An existing aerodynamic model (that predicts the aerodynamic efficiency) is merged with the developed structural and aeroelastic models for the purpose of conducting parametric and optimization studies. The variables of interest are the wing thickness and structural properties, and extension and winglet planform variables. The Bell XV-15 tiltrotor aircraft the chosen as the parent aircraft for this study. Parametric studies reveal that a wing extension of span 25% of the inboard wing increases the whirl flutter speed by 10% and also increases the aircraft aerodynamic efficiency by 8%. Structurally tapering the wing of a tiltrotor

  11. The interference aerodynamics caused by the wing elasticity during store separation

    Science.gov (United States)

    Lei, Yang; Zheng-yin, Ye

    2016-04-01

    Air-launch-to-orbit is the technology that has stores carried aloft and launched the store from the plane to the orbit. The separation between the aircraft and store is one of the most important and difficult phases in air-launch-to-orbit technology. There exists strong aerodynamic interference between the aircraft and the store in store separation. When the aspect ratio of the aircraft is large, the elastic deformations of the wing must be considered. The main purpose of this article is to study the influence of the interference aerodynamics caused by the elastic deformations of the wing to the unsteady aerodynamics of the store. By solving the coupled functions of unsteady Navier-Stokes equations, six degrees of freedom dynamic equations and structural dynamic equations simultaneously, the store separation with the elastic deformation of the aircraft considered is simulated numerically. And the interactive aerodynamic forces are analyzed. The study shows that the interference aerodynamics is obvious at earlier time during the separation, and the dominant frequency of the elastic wing determines the aerodynamic forces frequencies of the store. Because of the effect of the interference aerodynamics, the roll angle response and pitch angle response increase. When the store is mounted under the wingtip, the additional aerodynamics caused by the wingtip vortex is obvious, which accelerate the divergence of the lateral force and the lateral-directional attitude angle of the store. This study supports some beneficial conclusions to the engineering application of the air-launch-to-orbit.

  12. Nonlinear analysis and enhancement of wing-based piezoaeroelastic energy harvesters

    KAUST Repository

    Abdelkefi, Abdessattar

    2014-01-01

    We investigate the level of harvested power from aeroelastic vibrations for an elastically mounted wing supported by nonlinear springs. The energy is harvested by attaching a piezoelectric transducer to the plunge degree of freedom. The considered wing has a low-aspect ratio and hence three dimensional aerodynamic effects cannot be neglected. To this end, the three dimensional unsteady vortex lattice method for the prediction of the unsteady aerodynamic loads is developed. A strong coupling scheme that is based on Hamming\\'s fourth-order predictor-corrector method and accounts for the interaction between the aerodynamic loads and the motion of the wing is employed. The effects of the electrical load resistance, nonlinear torsional spring and eccentricity between the elastic axis and the gravity axis on the level of the harvested power, pitch and plunge amplitudes are investigated for a range of operating wind speeds. The results show that there is a specific wind speed beyond which the pitch motion does not pick any further energy from the incident flow. As such, the displacement in the plunge direction grows significantly and causes enhanced energy harvesting. The results also show that the nonlinear torsional spring plays an important role in enhancing the level of the harvested power. Furthermore, the harvested power can be increased by an order of magnitude by properly choosing the eccentricity and the load resistance. This analysis is helpful in designing piezoaeroelastic energy harvesters that can operate optimally at specific wind speeds. © 2013 Elsevier Ltd.

  13. Influence of cuticle nanostructuring on the wetting behaviour/states on cicada wings.

    Directory of Open Access Journals (Sweden)

    Mingxia Sun

    Full Text Available The nanoscale protrusions of different morphologies on wing surfaces of four cicada species were examined under an environmental scanning electron microscope (ESEM. The water contact angles (CAs of the wing surfaces were measured along with droplet adhesion values using a high-sensitivity microelectromechanical balance system. The water CA and adhesive force measurements obtained were found to relate to the nanostructuring differences of the four species. The adhesive forces in combination with the Cassie-Baxter and Wenzel approximations were used to predict wetting states of the insect wing cuticles. The more disordered and inhomogeneous surface of the species Leptopsalta bifuscata demonstrated a Wenzel type wetting state or an intermediate state of spreading and imbibition with a CA of 81.3° and high adhesive force of 149.5 µN. Three other species (Cryptotympana atrata, Meimuna opalifer and Aola bindusara exhibited nanostructuring of the form of conically shaped protrusions, which were spherically capped. These surfaces presented a range of high adhesional values; however, the CAs were highly hydrophobic (C. atrata and A. bindusara and in some cases close to superhydrophobic (M. opalifer. The wetting states of A. bindusara, C. atrata and M. opalifer (based on adhesion and CAs are most likely represented by the transitional region between the Cassie-Baxter and Wenzel approximations to varying degrees.

  14. Sexual dichromatism in wing pigmentation of New World dragonflies follows Rensch's rule.

    Science.gov (United States)

    Santos, E S A; Machado, G

    2016-07-01

    Many animal taxa that display sexual size dimorphism (SSD) exhibit a positive allometric relationship in which the degree of dimorphism increases with body size. This macroevolutionary pattern is known as Rensch's rule. Although sexual selection is hypothesized to be the main mechanism causing this pattern, body size is influenced by several selective forces, including natural and sexual selection. Therefore, by focusing exclusively on SSD one cannot ascertain which of these selective forces drives Rensch's rule. If sexual selection is indeed the main mechanism underlying Rensch's rule, we predict that other sexually selected traits, including coloration-based ornaments, will also exhibit interspecific allometric scaling consistent with Rensch's rule. We tested this prediction using wing pigmentation of 89 species of dragonflies. Studies show that male wing pigmentation is generally under strong intra- and intersexual selection, so that sexual dichromatism in this trait should follow Rensch's rule. Conversely, the available evidence suggests that male body size is usually not sexually selected in dragonflies, so we do not expect SSD to follow Rensch's rule. First, we found that sexual dichromatism in wing pigmentation was consistent with Rensch's rule. The phylogenetic major axis regression slope was significantly greater than one. We also showed that the allometric slope for SSD was not different from unity, providing no support for Rensch's rule. Our results provide the first evidence that a trait which appears to be under strong sexual selection exhibits a pattern consistent with Rensch's rule.

  15. Folding in and out: passive morphing in flapping wings.

    Science.gov (United States)

    Stowers, Amanda K; Lentink, David

    2015-03-25

    We present a new mechanism for passive wing morphing of flapping wings inspired by bat and bird wing morphology. The mechanism consists of an unactuated hand wing connected to the arm wing with a wrist joint. Flapping motion generates centrifugal accelerations in the hand wing, forcing it to unfold passively. Using a robotic model in hover, we made kinematic measurements of unfolding kinematics as functions of the non-dimensional wingspan fold ratio (2-2.5) and flapping frequency (5-17 Hz) using stereo high-speed cameras. We find that the wings unfold passively within one to two flaps and remain unfolded with only small amplitude oscillations. To better understand the passive dynamics, we constructed a computer model of the unfolding process based on rigid body dynamics, contact models, and aerodynamic correlations. This model predicts the measured passive unfolding within about one flap and shows that unfolding is driven by centrifugal acceleration induced by flapping. The simulations also predict that relative unfolding time only weakly depends on flapping frequency and can be reduced to less than half a wingbeat by increasing flapping amplitude. Subsequent dimensional analysis shows that the time required to unfold passively is of the same order of magnitude as the flapping period. This suggests that centrifugal acceleration can drive passive unfolding within approximately one wingbeat in small and large wings. Finally, we show experimentally that passive unfolding wings can withstand impact with a branch, by first folding and then unfolding passively. This mechanism enables flapping robots to squeeze through clutter without sophisticated control. Passive unfolding also provides a new avenue in morphing wing design that makes future flapping morphing wings possibly more energy efficient and light-weight. Simultaneously these results point to possible inertia driven, and therefore metabolically efficient, control strategies in bats and birds to morph or recover

  16. Degree-degree dependencies in random graphs with heavy-tailed degrees

    NARCIS (Netherlands)

    Hofstad, van der Remco; Litvak, Nelly

    2014-01-01

    Mixing patterns in large self-organizing networks, such as the Internet, the World Wide Web, social, and biological networks are often characterized by degree-degree dependencies between neighboring nodes. In assortative networks, the degree-degree dependencies are positive (nodes with similar degre

  17. Degree-Degree Dependencies in Random Graphs with Heavy-Tailed Degrees

    NARCIS (Netherlands)

    van der Hofstad, Remco; Litvak, Nelli

    2014-01-01

    Mixing patterns in large self-organizing networks, such as the Internet, the World Wide Web, social, and biological networks are often characterized by degree-degree dependencies between neighboring nodes. In assortative networks, the degree-degree dependencies are positive (nodes with similar

  18. Three-dimensional winged nanocone optical antennas.

    Science.gov (United States)

    Huttunen, Mikko J; Lindfors, Klas; Andriano, Domenico; Mäkitalo, Jouni; Bautista, Godofredo; Lippitz, Markus; Kauranen, Martti

    2014-06-15

    We introduce 3D optical antennas based on winged nanocones. The antennas support particle plasmon oscillations with current distributions that facilitate transformation of transverse far-field radiation to strong longitudinal local fields near the cone apices. We characterize the optical responses of the antennas by their extinction spectra and by second-harmonic generation microscopy with cylindrical vector beams. The results demonstrate a new 3D polarization-controllable optical antenna for applications in apertureless near-field microscopy, spectroscopy, and plasmonic sensing.

  19. Quantitative modeling of degree-degree correlation in complex networks

    CERN Document Server

    Niño, Alfonso

    2013-01-01

    This paper presents an approach to the modeling of degree-degree correlation in complex networks. Thus, a simple function, \\Delta(k', k), describing specific degree-to- degree correlations is considered. The function is well suited to graphically depict assortative and disassortative variations within networks. To quantify degree correlation variations, the joint probability distribution between nodes with arbitrary degrees, P(k', k), is used. Introduction of the end-degree probability function as a basic variable allows using group theory to derive mathematical models for P(k', k). In this form, an expression, representing a family of seven models, is constructed with the needed normalization conditions. Applied to \\Delta(k', k), this expression predicts a nonuniform distribution of degree correlation in networks, organized in two assortative and two disassortative zones. This structure is actually observed in a set of four modeled, technological, social, and biological networks. A regression study performed...

  20. Flow structure and vorticity transport on a plunging wing

    Science.gov (United States)

    Eslam Panah, Azar

    The structure and dynamics of the flow field created by a plunging flat plate airfoil are investigated at a chord Reynolds number of 10,000 while varying plunge amplitude and Strouhal number. Digital particle image velocimetry measurements are used to characterize the shedding patterns and the interactions between the leading and trailing edge vortex structures (LEV and TEV), resulting in the development of a wake classification system based on the nature and timing of interactions between the leading- and trailing-edge vortices. The convection speed of the LEV and its resulting interaction with the TEV is primarily dependent on reduced frequency; however, at Strouhal numbers above approximately 0.4, a significant influence of Strouhal number (or plunge amplitude) is observed in which LEV convection is retarded, and the contribution of the LEV to the wake is diminished. It is shown that this effect is caused by an enhanced interaction between the LEV and the airfoil surface, due to a significant increase in the strength of the vortices in this Strouhal number range, for all plunge amplitudes investigated. Comparison with low-Reynolds-number studies of plunging airfoil aerodynamics reveals a high degree of consistency and suggests applicability of the classification system beyond the range examined in the present work. Some important differences are also observed. The three-dimensional flow field was characterized for a plunging two-dimensional flat-plate airfoil using three-dimensional reconstructions of planar PIV data. Whereas the phase-averaged description of the flow field shows the secondary vortex penetrating the leading-edge shear layer to terminate LEV formation on the airfoil, time-resolved, instantaneous PIV measurements show a continuous and growing entrainment of secondary vorticity into the shear layer and LEV. A planar control volume analysis on the airfoil indicated that the generation of secondary vorticity produced approximately one half the

  1. VizieR Online Data Catalog: OmegaWINGS local clusters of galaxies redshifts (Moretti+, 2017)

    Science.gov (United States)

    Moretti, A.; Gullieuszik, M.; Poggianti, B.; Paccagnella, A.; Couch, W. J.; Vulcani, B.; Bettoni, D.; Fritz, J.; Cava, A.; Fasaano, G.; D'Onofrio, M.; Omizzolo, A.

    2017-02-01

    Redshifts, magnitude/radial completeness, and memberships are given for the 17985 galaxies observed as part of the OmegaWINGS survey of local clusters of galaxies over 1 square degree. Redshifts have been measured using both absorption and emission lines features. The sample magnitude completeness is 80% at V=20. Thanks to the observing strategy, the radial completeness turned out to be relatively constant (90%) within the AAOmega field of view. The success rate in measuring redshifts is 95%, at all radii. Cluster members are flagged 1 or 2, depending on the cluster structure/secondary structure, and 0 if they are not cluster members. (1 data file).

  2. Variable Geometry Aircraft Wing Supported by Struts And/Or Trusses

    Science.gov (United States)

    Melton, John E. (Inventor); Dudley, Michael R. (Inventor)

    2016-01-01

    The present invention provides an aircraft having variable airframe geometry for accommodating efficient flight. The aircraft includes an elongated fuselage, an oblique wing pivotally connected with said fuselage, a wing pivoting mechanism connected with said oblique wing and said fuselage, and a brace operably connected between said oblique wing and said fuselage. The present invention also provides an aircraft having an elongated fuselage, an oblique wing pivotally connected with said fuselage, a wing pivoting mechanism connected with said oblique wing and said fuselage, a propulsion system pivotally connected with said oblique wing, and a brace operably connected between said propulsion system and said fuselage.

  3. Morphing Wing Design with an Innovative Three-Dimensional Warping Actuation Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advanced wing configurations where traditional control surfaces are replaced by dynamically controlled distribution of wing twist and/or camber can provide...

  4. Sniffing by a silkworm moth: wing fanning enhances air penetration through and pheromone interception by antennae.

    Science.gov (United States)

    Loudon, C; Koehl, M A

    2000-10-01

    Many organisms increase the air or water flow adjacent to olfactory surfaces when exposed to appropriate chemical stimuli; such 'sniffing' samples fluid from a specific region and can increase the rate of interception of odorant molecules. We used hot-wire anemometry, high-speed videography and flow visualization to study air flow near the feathery olfactory antennae of male silkworm moths (Bombyx mori L.). When exposed to conspecific female sex pheromone, male B. mori flap their wings through a stroke angle of 90-110 degrees at approximately 40 Hz without flying. This behavior generates an unsteady flow of air (mean speed 0.3-0.4 m s(-1)) towards the antennae from the front of the male. A pulse of peak air speed occurs at each wing upstroke. The Womersley number (characterizing the damping of pulsatile flow through the gaps between the sensory hairs on the antennae) is less than 1; hence, pulses of faster air (at 40 Hz) should move between sensory hairs. Calculation of flow through arrays of cylinders suggest that this wing fanning can increase the rate of interception of pheromone by the sensory hairs on the antennae by at least an order of magnitude beyond that in still air. Although wing fanning produces air flow relative to the antennae that is approximately 15 times faster than that generated by walking at top speed (0.023 m s(-1)), air flow through the gaps between the sensory hairs is approximately 560 times faster because a dramatic increase in the leakiness of the feathery antennae to air flow occurs at the air velocities produced by fanning.

  5. Design and Performance of Insect-Scale Flapping-Wing Vehicles

    Science.gov (United States)

    Whitney, John Peter

    Micro-air vehicles (MAVs)---small versions of full-scale aircraft---are the product of a continued path of miniaturization which extends across many fields of engineering. Increasingly, MAVs approach the scale of small birds, and most recently, their sizes have dipped into the realm of hummingbirds and flying insects. However, these non-traditional biologically-inspired designs are without well-established design methods, and manufacturing complex devices at these tiny scales is not feasible using conventional manufacturing methods. This thesis presents a comprehensive investigation of new MAV design and manufacturing methods, as applicable to insect-scale hovering flight. New design methods combine an energy-based accounting of propulsion and aerodynamics with a one degree-of-freedom dynamic flapping model. Important results include analytical expressions for maximum flight endurance and range, and predictions for maximum feasible wing size and body mass. To meet manufacturing constraints, the use of passive wing dynamics to simplify vehicle design and control was investigated; supporting tests included the first synchronized measurements of real-time forces and three-dimensional kinematics generated by insect-scale flapping wings. These experimental methods were then expanded to study optimal wing shapes and high-efficiency flapping kinematics. To support the development of high-fidelity test devices and fully-functional flight hardware, a new class of manufacturing methods was developed, combining elements of rigid-flex printed circuit board fabrication with "pop-up book" folding mechanisms. In addition to their current and future support of insect-scale MAV development, these new manufacturing techniques are likely to prove an essential element to future advances in micro-optomechanics, micro-surgery, and many other fields.

  6. Coloration principles of nymphaline butterflies - thin films, melanin, ommochromes and wing scale stacking.

    Science.gov (United States)

    Stavenga, Doekele G; Leertouwer, Hein L; Wilts, Bodo D

    2014-06-15

    The coloration of the common butterflies Aglais urticae (small tortoiseshell), Aglais io (peacock) and Vanessa atalanta (red admiral), belonging to the butterfly subfamily Nymphalinae, is due to the species-specific patterning of differently coloured scales on their wings. We investigated the scales' structural and pigmentary properties by applying scanning electron microscopy, (micro)spectrophotometry and imaging scatterometry. The anatomy of the wing scales appears to be basically identical, with an approximately flat lower lamina connected by trabeculae to a highly structured upper lamina, which consists of an array of longitudinal, parallel ridges and transversal crossribs. Isolated scales observed at the abwing (upper) side are blue, yellow, orange, red, brown or black, depending on their pigmentation. The yellow, orange and red scales contain various amounts of 3-OH-kynurenine and ommochrome pigment, black scales contain a high density of melanin, and blue scales have a minor amount of melanin pigment. Observing the scales from their adwing (lower) side always revealed a structural colour, which is blue in the case of blue, red and black scales, but orange for orange scales. The structural colours are created by the lower lamina, which acts as an optical thin film. Its reflectance spectrum, crucially determined by the lamina thickness, appears to be well tuned to the scales' pigmentary spectrum. The colours observed locally on the wing are also due to the degree of scale stacking. Thin films, tuned pigments and combinations of stacked scales together determine the wing coloration of nymphaline butterflies. © 2014. Published by The Company of Biologists Ltd.

  7. Soap film flow visualization investigations of oscillating wing energy harvesters

    Science.gov (United States)

    Kirschmeier, Benjamin; Bryant, Matthew

    2015-03-01

    With increasing population and proliferation of wireless electronics, significant research attention has turned to harvesting energy from ambient sources such as wind and water flows at scales ranging from micro-watt to mega-watt levels. One technique that has recently attracted attention is the application of bio-inspired flapping wings for energy harvesting. This type of system uses a heaving and pitching airfoil to extract flow energy and generate electricity. Such a device can be realized using passive devices excited by aeroelastic flutter phenomena, kinematic mechanisms driven by mechanical linkages, or semi-active devices that are actively controlled in one degree of freedom and passively driven in another. For these types of systems, numerical simulations have showed strong dependence on efficiency and vortex interaction. In this paper we propose a new apparatus for reproducing arbitrary pitch-heave waveforms to perform flow visualization experiments in a soap film tunnel. The vertically falling, gravity driven soap film tunnel is used to replicate flows with a chord Reynolds number on the order of 4x104. The soap film tunnel is used to investigate leading edge vortex (LEV) and trailing edge vortex (TEV) interactions for sinusoidal and non-sinusoidal waveforms. From a qualitative analysis of the fluid structure interaction, we have been able to demonstrate that the LEVs for non-sinusoidal motion convect faster over the airfoil compared with sinusoidal motion. Signifying that optimal flapping frequency is dependent on the motion profile.

  8. Global Local Structural Optimization of Transportation Aircraft Wings

    NARCIS (Netherlands)

    Ciampa, P.D.; Nagel, B.; Van Tooren, M.J.L.

    2010-01-01

    The study presents a multilevel optimization methodology for the preliminary structural design of transportation aircraft wings. A global level is defined by taking into account the primary wing structural components (i.e., ribs, spars and skin) which are explicitly modeled by shell layered finite e

  9. Inertial Force Coupling to Nonlinear Aeroelasticity of Flexible Wing Aircraft

    Science.gov (United States)

    Nguyen, Nhan T.; Ting, Eric

    2016-01-01

    This paper investigates the inertial force effect on nonlinear aeroelasticity of flexible wing aircraft. The geometric are nonlinearity due to rotational and tension stiffening. The effect of large bending deflection will also be investigated. Flutter analysis will be conducted for a truss-braced wing aircraft concept with tension stiffening and inertial force coupling.

  10. Ray analysis of a class of hybrid cylindrical aircraft wings

    OpenAIRE

    Jha, RM; Bokhari, SA; Sudhakan, V; Mahapatra, PR

    1988-01-01

    A new approach to the modelling of aircraft wings, based on the combination of hybrid quadric (parabolic and circular) cylinders, has been presented for electromagnetic applications. Closed-form expressions have been obtained for ray parameters required in the high-frequency mutual coupling computation of antenna pairs located arbitrarily on an aircraft wing.

  11. Influence of anisotropic piezoelectric actuators on wing aerodynamic forces

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Changing the shape of an airfoil to enhance overall aircraft performance has always been a goal of aircraft designers. Using smart material to reshape the wing can improve aerodynamic performance. The influence of anisotropic effects of piezoelectric actuators on the aerodynamic characteristics of a simplified HALE wing model was investigated. Test verification was conducted.

  12. Energy-based Aeroelastic Analysis and Optimisation of Morphing Wings

    NARCIS (Netherlands)

    De Breuker, R.

    2011-01-01

    Morphing aircraft can change their shape radically when confronted with a variety of conflicting flight conditions throughout their mission. For instance the F-14 Tomcat fighter aircraft, known from the movie Top Gun, was able to sweep its wings from a straight wing configuration to a highly swept v

  13. Influence of anisotropic piezoelectric actuators on wing aerodynamic forces

    Institute of Scientific and Technical Information of China (English)

    GUAN De; LI Min; LI Wei; WANG MingChun

    2008-01-01

    Changing the shape of an airfoil to enhance overall aircraft performance has always been s goal of aircraft designers.Using smart material to reshape the wing can improve aerodynamic performance.The influence of anisotropic effects of piezo-electric actuators on the aerodynamic characteristics of a simplified HALE wing model was investigated.Test verification was conducted.

  14. Significance of wing morphometry in distinguishing some of the ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-07-20

    Jul 20, 2009 ... the photos, Scale factor values were shown on the ruler. Wing pho- tos were ... Analysis of wing Landmark data (in TPS format). At the end of the .... not clearly separated, and most groups were mixed. (Figure 9, Table 7).

  15. Wing flexibility effects in clap-and-fling

    NARCIS (Netherlands)

    Percin, M.; Hu, Y.; Van Oudheusden, B.W.; Remes, B.; Scarano, F.

    2011-01-01

    The work explores the use of time-resolved tomographic PIV measurements to study a flapping-wing model, the related vortex generation mechanisms and the effect of wing flexibility on the clap-and-fling movement in particular. An experimental setup is designed and realized in a water t

  16. The function of PS integrins in Drosophila wing morphogenesis.

    Science.gov (United States)

    Wilcox, M; DiAntonio, A; Leptin, M

    1989-12-01

    Integrins are found on many cell types during the development of most organisms. In Drosophila their functions can be analysed genetically. An analysis of lethal mutations in a PS integrin gene showed that the integrins were required for muscle attachment and for certain cell sheet migrations during embryogenesis. In this paper we use viable mutations in integrin component genes to look at integrin function in the later stages of development of one adult structure, the wing. We show that two known viable mutations, one which has its primary effect on the fly's escape response, the other on wing morphogenesis, are mutations in the beta and PS2alpha subunits, respectively, of the PS integrins. The mutation non-jumper (mys(mj42)) in the beta subunit leads to wasting of the thoracic jump muscles. Flies in which the dosage of this allele is reduced (and no wildtype copy is present) show defects also in wing morphogenesis. The two surfaces of the wing fail to connect properly, resulting in 'blistering' of the wing and the formation of extra crossveins. The mutation in the gene for the PS2alpha integrin subunit, inflated, also leads to a failure in wing surface apposition and consequent wing blistering. When the two mutations are combined, the mutant phenotype is greatly enhanced. Thus, one of the roles of the PS integrins in late Drosophila development is to ensure the correct apposition and patterning of the wing epithelia.

  17. Anisotropism of the Non-Smooth Surface of Butterfly Wing

    Institute of Scientific and Technical Information of China (English)

    Gang Sun; Yan Fang; Qian Cong; Lu-quan Ren

    2009-01-01

    Twenty-nine species of butterflies were collected for observation and determination of the wing surfaces using a Scanning Electron Microscope (SEM). Butterfly wing surface displays structural anisotropism in micro-, submicro- and nano-scales. The scales on butterfly wing surface arrange like overlapping roof tiles. There are submicrometric vertical gibbosities, horizontal links, and nano-protuberances on the scales. First-incline-then-drip method and first-drip-then-incline method were used to measure the Sliding Angle (SA) of droplet on butterfly wing surface by an optical Contact Angle (CA) measuring system.Relatively smaller sliding angles indicate that the butterfly wing surface has fine self-cleaning property. Significantly different SAs in various directions indicate the anisotropic self-cleaning property of butterfly wing surface. The SAs on the butterfly wing surface without scales are remarkably larger than those with scales, which proves the crucial role of scales in determining the self-cleaning property. Butterfly wing surface is a template for design and fabrication of biomimetic materials and self-cleaning substrates. This work may offer insights into how to design directional self-cleaning coatings and anisotropic wetting surface.

  18. Unsteady Aerodynamics of Flapping Wing of a Bird

    Directory of Open Access Journals (Sweden)

    M. Agoes Moelyadi

    2013-04-01

    Full Text Available The unsteady flow behavior and time-dependent aerodynamic characteristics of the flapping motion of a bird’s wing were investigated using a computational method. During flapping, aerodynamic interactions between bird wing surfaces and surrounding flow may occur, generating local time-dependent flow changes in the flow field and aerodynamic load of birds. To study the effect of flapping speed on unsteady aerodynamic load, two kinds of computational simulations were carried out, namely a quasi-steady and an unsteady simulation. To mimic the movement of the down-stroke and the upstroke of a bird, the flapping path accorded to a sinus function, with the wing attitude changing in dihedral angle and time. The computations of time-dependent viscous flow were based on the solution of the Reynolds Averaged Navier-Stokes equations by applying the k-e turbulence model. In addition, the discretization for the computational domain around the model used multi-block structured grid to provide more accuracy in capturing viscous flow, especially in the vicinity of the wing and body surfaces, to obtain a proper wing-body geometry model. For this research, the seagull bird was chosen, which has high aspect ratio wings with pointed wing-tips and a high camber wing section. The results include mesh movement, velocity contours as well as aerodynamic coefficients of the flapping motion of the bird at various flapping frequencies.

  19. Stable structural color patterns displayed on transparent insect wings.

    Science.gov (United States)

    Shevtsova, Ekaterina; Hansson, Christer; Janzen, Daniel H; Kjærandsen, Jostein

    2011-01-11

    Color patterns play central roles in the behavior of insects, and are important traits for taxonomic studies. Here we report striking and stable structural color patterns--wing interference patterns (WIPs)--in the transparent wings of small Hymenoptera and Diptera, patterns that have been largely overlooked by biologists. These extremely thin wings reflect vivid color patterns caused by thin film interference. The visibility of these patterns is affected by the way the insects display their wings against various backgrounds with different light properties. The specific color sequence displayed lacks pure red and matches the color vision of most insects, strongly suggesting that the biological significance of WIPs lies in visual signaling. Taxon-specific color patterns are formed by uneven membrane thickness, pigmentation, venation, and hair placement. The optically refracted pattern is also stabilized by microstructures of the wing such as membrane corrugations and spherical cell structures that reinforce the pattern and make it essentially noniridescent over a large range of light incidences. WIPs can be applied to map the micromorphology of wings through direct observation and are useful in several fields of biology. We demonstrate their usefulness as identification patterns to solve cases of cryptic species complexes in tiny parasitic wasps, and indicate their potentials for research on the genetic control of wing development through direct links between the transregulatory wing landscape and interference patterns we observe in Drosophila model species. Some species display sexually dimorphic WIPs, suggesting sexual selection as one of the driving forces for their evolution.

  20. Closed-type wing for drones: positive and negative characteristics

    Directory of Open Access Journals (Sweden)

    Leonid I. Gretchihin

    2014-02-01

    Full Text Available The paper presents the aerodynamics of a wing of a closed oval ellipsoidal shape, designed with the use of the molecular-kinetic theory. The positive and negative characteristics of aircraft - drones with an oval wing are described. The theoretical calculations have been experimentally checked.

  1. Jet reorientation in active galactic nuclei : two winged radio galaxies

    NARCIS (Netherlands)

    Dennett-Thorpe, J; Scheuer, PAG; Laing, RA; Bridle, AH; Pooley, GG; Reich, W

    2002-01-01

    Winged, or X-shaped, radio sources form a small class of morphologically peculiar extragalactic sources. We present multifrequency radio observations of two such sources. We derive maximum ages since any re-injection of fresh particles of 34 and 17 Myr for the wings of 3C 223.1 and 3C 403 respective

  2. Flapping-wing mechanical butterfly on a wheel

    Science.gov (United States)

    Godoy-Diana, Ramiro; Thiria, Benjamin; Pradal, Daniel

    2009-11-01

    We examine the propulsive performance of a flapping-wing device turning on a ``merry-go-round'' type base. The two-wing flapper is attached to a mast that is ball-bearing mounted to a central shaft in such a way that the thrust force produced by the wings makes the flapper turn around this shaft. The oscillating lift force produced by the flapping wings is aligned with the mast to avoid vibration of the system. A turning contact allows to power the motor that drives the wings. We measure power consumption and cruising speed as a function of flapping frequency and amplitude as well as wing flexibility. The design of the wings permits to change independently their flexibility in the span-wise and chord-wise directions and PIV measurements in various planes let us examine the vorticity field around the device. A complete study of the effect of wing flexibility on the propulsive performance of the system will be presented at the conference.

  3. Vortex interactions with flapping wings and fins can be unpredictable

    NARCIS (Netherlands)

    Lentink, D.; Heijst, van G.J.F.; Muijres, F.T.; Leeuwen, van J.L.

    2010-01-01

    As they fly or swim, many animals generate a wake of vortices with their flapping fins and wings that reveals the dynamics of their locomotion. Previous studies have shown that the dynamic interaction of vortices in the wake with fins and wings can increase propulsive force. Here, we explore whether

  4. Flexibility and inertia of flapping wings in forward flight

    Science.gov (United States)

    Tian, Fang-Bao; Luo, Haoxiang; Lu, Xi-Yun

    2011-11-01

    Insect wings typically deform passively in flight under the combined aerodynamic force and inertia of the wing. To study the effect of the wing flexibility on the aerodynamic performance, a two-dimensional numerical study is employed to simulate the fluid-structure interaction of an elastic plate performing forward flight. The leading edge of the plate is clamped, while the rest of the chord is free to deform, leading to passive pitching and a dynamic camber. The wing stiffness and mass ratio are varied, and their effects on the lift, thrust, and aerodynamic power are investigated. The results shows that the moderate chordwise deformation can improve both lift and thrust performance significantly. The instantaneous passive pitching angle and consequently the forces are largely affected by the mass ratio that determines whether the deformation is caused by the wing inertia or the aerodynamic force. The high mass ratio wings, whose deformation is due to the wing inertia, can produce more thrust than the low mass ratio wing at the same amount of deformation. However, the high thrust is gained at a price of more power requirement. This work is sponsored by the U.S. NSF and the NSF of China.

  5. On the Minimum Induced Drag of Wings

    Science.gov (United States)

    Bowers, Albion H.

    2011-01-01

    Of all the types of drag, induced drag is associated with the creation and generation of lift over wings. Induced drag is directly driven by the span load that the aircraft is flying at. The tools by which to calculate and predict induced drag we use were created by Ludwig Prandtl in 1903. Within a decade after Prandtl created a tool for calculating induced drag, Prandtl and his students had optimized the problem to solve the minimum induced drag for a wing of a given span, formalized and written about in 1920. This solution is quoted in textbooks extensively today. Prandtl did not stop with this first solution, and came to a dramatically different solution in 1932. Subsequent development of this 1932 solution solves several aeronautics design difficulties simultaneously, including maximum performance, minimum structure, minimum drag loss due to control input, and solution to adverse yaw without a vertical tail. This presentation lists that solution by Prandtl, and the refinements by Horten, Jones, Kline, Viswanathan, and Whitcomb.

  6. New aeroelastic studies for a morphing wing

    Directory of Open Access Journals (Sweden)

    Ruxandra Mihaela BOTEZ*

    2012-06-01

    Full Text Available For this study, the upper surface of a rectangular finite aspect ratio wing, with a laminar airfoil cross-section, was made of a carbon-Kevlar composite material flexible skin. This flexible skin was morphed by use of Shape Memory Alloy actuators for 35 test cases characterized by combinations of Mach numbers, Reynolds numbers and angles of attack. The Mach numbers varied from 0.2 to 0.3 and the angles of attack ranged between -1° and 2°. The optimized airfoils were determined by use of the CFD XFoil code. The purpose of this aeroelastic study was to determine the flutter conditions to be avoided during wind tunnel tests. These studies show that aeroelastic instabilities for the morphing configurations considered appeared at Mach number 0.55, which was higher than the wind tunnel Mach number limit speed of 0.3. The wind tunnel tests could thus be performed safely in the 6’×9’ wind tunnel at the Institute for Aerospace Research at the National Research Council Canada (IAR/NRC, where the new aeroelastic studies, applied on morphing wings, were validated.

  7. Limb disparity and wing shape in pterosaurs.

    Science.gov (United States)

    Dyke, G J; Nudds, R L; Rayner, J M V

    2006-07-01

    The limb proportions of the extinct flying pterosaurs were clearly distinct from their living counterparts, birds and bats. Within pterosaurs, however, we show that further differences in limb proportions exist between the two main groups: the clade of short-tailed Pterodactyloidea and the paraphyletic clades of long-tailed rhamphorhynchoids. The hindlimb to forelimb ratios of rhamphorhynchoid pterosaurs are similar to that seen in bats, whereas those of pterodactyloids are much higher. Such a clear difference in limb ratios indicates that the extent of the wing membrane in rhamphorhynchoids and pterodactyloids may also have differed; this is borne out by simple ternary analyses. Further, analyses also indicate that the limbs of Sordes pilosus, a well-preserved small taxon used as key evidence for inferring the extent and shape of the wing membrane in all pterosaurs, are not typical even of its closest relatives, other rhamphorhynchoids. Thus, a bat-like extensive hindlimb flight membrane, integrated with the feet and tail may be applicable only to a small subset of pterosaur diversity. The range of flight morphologies seen in these extinct reptiles may prove much broader than previously thought.

  8. STUDY OF WING SHIELDING EFFECT OF PROPELLER AIRCRAFT

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The calculation of wing shielding effect starts from solving Ffowcs Williams and Hawkings equation without quadrupole source in time domain. The sound scattering of the wing and fuselage which are surrounded by a multi-propeller sound field is modeled as a second sound source. A program is developed to calculate the acoustical effects of the rigid fuselage as well as wings with arbitrary shape in motion at low Mach number. As an example, the numerical calculation of the wing shielding of Y12 aircraft with an approximate shape is presented. The result manifests clearly the shielding effect of the wing on the fuselage and the approach is more efficient than that published before.

  9. Unsteady flow past wings having sharp-edge separation

    Science.gov (United States)

    Atta, E. H.; Kandil, O. A.; Mook, D. T.; Nayfeh, A. H.

    1976-01-01

    A vortex-lattice technique is developed to model unsteady, incompressible flow past thin wings. This technique predicts the shape of the wake as a function of time; thus, it is not restricted by planform, aspect ratio, or angle of attack as long as vortex bursting does not occur and the flow does not separate from the wing surface. Moreover, the technique can be applied to wings of arbitrary curvature undergoing general motion; thus, it can treat rigid-body motion, arbitrary wing deformation, gusts in the freestream, and periodic motions. Numerical results are presented for low-aspect rectangular wings undergoing a constant-rate, rigid-body rotation about the trailing edge. The results for the unsteady motion are compared with those predicted by assuming quasi-steady motion. The present results exhibit hysteretic behavior.

  10. Effects of Wing-Cuff on NACA 23015 Aerodynamic Performances

    Directory of Open Access Journals (Sweden)

    Meftah S.M.A

    2014-03-01

    Full Text Available The main subject of this work is the numerical study control of flow separation on a NACA 23015 airfoil by using wing cuff. This last is a leading edge modification done to the wing. The modification consists of a slight extension of the chord on the outboard section of the wings. Different numerical cases are considered for the baseline and modified airfoil NACA 23015 according at different angle of incidence. The turbulence is modeled by two equations k-epsilon model. The results of this numerical investigation showed several benefits of the wing cuff compared with a conventional airfoil and an agreement is observed between the experimental data and the present study. The most intriguing result of this research is the capability for wing cuff to perform short take-offs and landings.

  11. The Aerodynamics of Deforming Wings at Low Reynolds Number

    Science.gov (United States)

    Medina, Albert

    Flapping flight has gained much attention in the past decade driven by the desire to understand capabilities observed in nature and the desire to develop agile small-scale aerial vehicles. Advancing our current understanding of unsteady aerodynamics is an essential component in the development of micro-air vehicles (MAV) intended to utilize flight mechanics akin to insect flight. Thus the efforts undertaken that of bio-mimicry. The complexities of insect wing motion are dissected and simplified to more tractable problems to elucidate the fundamentals of unsteady aerodynamics in biologically inspired kinematics. The MAV's fruition would satisfy long established needs in both the military and civilian sectors. Although recent studies have provided great insight into the lift generating mechanisms of flapping wings the deflection response of such wings remains poorly understood. This dissertation numerically and experimentally investigates the aerodynamic performance of passively and actively deflected wings in hover and rotary kinematics. Flexibility is distilled to discrete lines of flexion which acknowledging major flexion lines in insect wings to be the primary avenue for deformation. Of primary concern is the development of the leading-edge vortex (LEV), a high circulation region of low pressure above the wing to which much of the wing's lift generation is attributed. Two-dimensional simulations of wings with chord-wise flexibility in a freestream reveal a lift generating mechanism unavailable to rigid wings with origins in vortical symmetry breaking. The inclusion of flexibility in translating wings accelerated from rest revealed the formation time of the initial LEV was very weakly dependent on the flexible stiffness of the wing, maintaining a universal time scale of four to five chords of travel before shedding. The frequency of oscillatory shedding of the leading and trailing-edge vortices that develops after the initial vortex shedding was shown to be

  12. Four-winged flapping flyer in forward flight

    CERN Document Server

    Godoy-Diana, Ramiro; Centeno, Mariana; Weinreb, Alexis; Thiria, Benjamin

    2015-01-01

    We study experimentally a four-winged flapping flyer with chord-wise flexible wings in a self-propelled setup. For a given physical configuration of the flyer (i.e. fixed distance between the forewing and hindwing pairs and fixed wing flexibility), we explore the kinematic parameter space constituted by the flapping frequency and the forewing-hindwing phase lag. Cruising speed and consumed electric power measurements are performed for each point in the $(f,\\varphi)$ parameter space and allow us to discuss the problem of performance and efficiency in four-winged flapping flight. We show that different phase-lags are needed for the system to be optimised for fastest flight or lowest energy consumption. A conjecture of the underlying mechanism is proposed in terms of the coupled dynamics of the forewing-hindwing phase lag and the deformation kinematics of the flexible wings.

  13. Design and Construction of Passively Articulated Ornithopter Wings

    Science.gov (United States)

    Mastro, Alexander Timothy

    Birds, bats, and insects are able to fly efficiently and execute impressive in-flight, landing, and takeoff maneuvers with apparent ease through actuation of their highly articulated wings. This contrasts the approach used to enable the flight of comparatively simple man-made rotary and fixed wing aircraft. The complex aerodynamics underlying flapping-based flight pose an everpresent challenge to scientists hoping to reveal the secrets of animal flight. Despite this, interest in engineering aircraft on the bird and insect scale is higher than ever. Herein, I present my attempt to design and construct bioinspired passively articulated ornithopter wings. Two different hinge-based joint design concepts are investigated across several design iterations. The advantages and disadvantages of each implementation are discussed. Finally, the necessary instrumentation to analyze the performance of the wings is designed and fabricated, followed by testing of the wings.

  14. Ontogeny of aerial righting and wing flapping in juvenile birds

    CERN Document Server

    Evangelista, Dennis; Huynh, Tony; Krivitskiy, Igor; Dudley, Robert

    2014-01-01

    Mechanisms of aerial righting in juvenile Chukar Partridge (Alectoris chukar) were studied from hatching through 14 days post hatching (dph). Asymmetric movements of the wings were used from 1 to 8 dph to effect progressively more successful righting behaviour via body roll. Following 8 dph, wing motions transitioned to bilaterally symmetric flapping that yielded aerial righting via nose down pitch, along with substantial increases in vertical force production during descent. Ontogenetically, the use of such wing motions to effect aerial righting precedes both symmetric flapping and a previously documented behaviour in chukar (i.e., wing assisted incline running) hypothesized to be relevant to incipient flight evolution in birds. These findings highlight the importance of asymmetric wing activation and controlled aerial manoeuvres during bird development, and are potentially relevant to understanding the origins of avian flight.

  15. Rethinking the Bachelor Degree Course

    DEFF Research Database (Denmark)

    Toft, Anne Elisabeth; Gammelgaard Nielsen, Anders

    2011-01-01

    The text contains reflections on the background for rethinking the bachelor degree course at the Aarhus School of Architecture.......The text contains reflections on the background for rethinking the bachelor degree course at the Aarhus School of Architecture....

  16. Dynamic Pattern Formation for Wings of Pterygota in an Eclosion ---Pattern Analysis for Wings with the Imago---

    Science.gov (United States)

    Seino, M.; Kakazu, Y.

    The vein and cell patterns for the fore and hind wing of Lepidoptera, Hemiptera, Orthoptera and Odonata are analyzed and discussed. For vein patterns of them, the fractal properties are shown and the inequality between four orders is obtained. The nature of wings observed by mass distributions for fractal dimensions of the vein pattern is presented.

  17. Foundation Degrees: A Risky Business?

    Science.gov (United States)

    Rowley, Jennifer

    2005-01-01

    Purpose: Foundation degrees, the new proposal for sub-degree vocational education in the UK, are characterised by innovation both in their design (curriculum, teaching, learning and assessment) and in the marketplace for which they are designed. This article argues that the development and delivery of foundation degrees carry a high level of risk,…

  18. Is there a right-wing alternative to the left-wing Bohemianism in Israel?

    Directory of Open Access Journals (Sweden)

    Cyril Aslanov

    2012-01-01

    Full Text Available Cet article s’efforce de comprendre les raisons de l’absence d’une bohème littéraire de droite en Israël. Au-delà des facteurs structurels liés à l’association naturelle de la bohème avec la gauche, soit comme un choix par défaut soit comme un terme marqué, le conservatisme inhérent à la littérature droitière est incompatible avec la renonciation au passé qui caractérise souvent les lettres israéliennes. En outre, la bohème de gauche en Israël ne tarit pas de critiques vis-à-vis de son propre pays. Cette préoccupation brille par son absence dans les écrits souvent partisans émanant de la droite. Enfin, la réception de la littérature israélienne hors d’Israël favorise nettement la bohème littéraire de gauche au point qu’on voit se dessiner une répartition complémentaire entre la droite aux commandes du pays et la gauche, maîtresse presque exclusive du Parnasse israélien.This article tries to understand why a right-wing literary Bohemianism failed to emerge in Israel. Besides the structural reasons connected with the natural association of Bohemianism with the Left, either as a default choice or as a marked option, the conservatism inherent to right-wing oriented literature is incompatible with modern Israeli attempt to get rid of the tradition. Moreover, what makes left-wing Israeli Bohemianism more credible is its constant need of self-criticism, a concern that blatantly lacks in the partisan writing emanating from the Right. Lastly, the reception abroad obviously favors left-wing Israeli Bohemianism to the extent that there might be a complementary distribution of functions between right-wing politics and left-wing literature in contemporary Israel.

  19. Multidisciplinary Design Optimization of A Highly Flexible Aeroservoelastic Wing

    Science.gov (United States)

    Haghighat, Sohrab

    A multidisciplinary design optimization framework is developed that integrates control system design with aerostructural design for a highly-deformable wing. The objective of this framework is to surpass the existing aircraft endurance limits through the use of an active load alleviation system designed concurrently with the rest of the aircraft. The novelty of this work is two fold. First, a unified dynamics framework is developed to represent the full six-degree-of-freedom rigid-body along with the structural dynamics. It allows for an integrated control design to account for both manoeuvrability (flying quality) and aeroelasticity criteria simultaneously. Secondly, by synthesizing the aircraft control system along with the structural sizing and aerodynamic shape design, the final design has the potential to exploit synergies among the three disciplines and yield higher performing aircraft. A co-rotational structural framework featuring Euler--Bernoulli beam elements is developed to capture the wing's nonlinear deformations under the effect of aerodynamic and inertial loadings. In this work, a three-dimensional aerodynamic panel code, capable of calculating both steady and unsteady loadings is used. Two different control methods, a model predictive controller (MPC) and a 2-DOF mixed-norm robust controller, are considered in this work to control a highly flexible aircraft. Both control techniques offer unique advantages that make them promising for controlling a highly flexible aircraft. The control system works towards executing time-dependent manoeuvres along with performing gust/manoeuvre load alleviation. The developed framework is investigated for demonstration in two design cases: one in which the control system simply worked towards achieving or maintaining a target altitude, and another where the control system is also performing load alleviation. The use of the active load alleviation system results in a significant improvement in the aircraft performance

  20. Static Aeroelastic and Longitudinal Trim Model of Flexible Wing Aircraft Using Finite-Element Vortex-Lattice Coupled Solution

    Science.gov (United States)

    Ting, Eric; Nguyen, Nhan; Trinh, Khanh

    2014-01-01

    This paper presents a static aeroelastic model and longitudinal trim model for the analysis of a flexible wing transport aircraft. The static aeroelastic model is built using a structural model based on finite-element modeling and coupled to an aerodynamic model that uses vortex-lattice solution. An automatic geometry generation tool is used to close the loop between the structural and aerodynamic models. The aeroelastic model is extended for the development of a three degree-of-freedom longitudinal trim model for an aircraft with flexible wings. The resulting flexible aircraft longitudinal trim model is used to simultaneously compute the static aeroelastic shape for the aircraft model and the longitudinal state inputs to maintain an aircraft trim state. The framework is applied to an aircraft model based on the NASA Generic Transport Model (GTM) with wing structures allowed to flexibly deformed referred to as the Elastically Shaped Aircraft Concept (ESAC). The ESAC wing mass and stiffness properties are based on a baseline "stiff" values representative of current generation transport aircraft.

  1. Effect of a wing-tip mounted pusher turboprop on the aerodynamic characteristics of a semi-span wing

    Science.gov (United States)

    Patterson, J. C., Jr.; Bartlett, G. R.

    1985-01-01

    An exploratory investigation has been conducted at the NASA Langley Research Center to determine the installed performance of a wing tip-mounted pusher turboprop. Tests were conducted using a semispan model having an unswept, untapered wing with a air-driven motor located on the tip of the wing, with an SR-2 design high speed propeller installed on the rear shaft of the motor. All tests were conducted at a Mach number of 0.70, at angles of attack of approximately -2 to +4 deg, and at a Reynolds number of 3.82 million based on the wing chord of 13 inches. The data indicate that, as a result of locating the propeller behind the wing trailing edge, at the wingtip, in the cross flow of the tip vortex, it is possible to recover part of the vortex energy as an increase in propeller thrust and, therefore, a reduction in the lift-induced drag as well.

  2. Effects of wing shape, aspect ratio and deviation angle on aerodynamic performance of flapping wings in hover

    Science.gov (United States)

    Shahzad, Aamer; Tian, Fang-Bao; Young, John; Lai, Joseph C. S.

    2016-11-01

    This numerical study is focused on assessing the effect on the aerodynamic hovering performance of wing shapes defined by the radius of the first moment of the wing area ( r 1 ¯ ) and aspect ratio (AR). In addition, the effect of introducing a deviation angle in the kinematics is examined. The performance of r 1 ¯ = 0 . 43 , 0.53, and 0.63 wings with AR of 1.5, 2.96, 4.5, and 6.0 is investigated at Reynolds numbers (Re) = 12, 400, and 13 500. The performance trends of the wing shapes have been observed to be independent of Re for both 2-angle and 3-angle kinematics. This is because high suction pressures associated with the leading-edge vortex are predominantly spread in the distal (away from the wing root) and leeward regions (towards the trailing-edge) of high flapping velocities for all the cases. While the deviation angle is detrimental to the production of lift and power economy (PE, defined as the ratio of the mean lift coefficient to the mean aerodynamic power coefficient) at Re = 12 due to strong viscous effects, it improves PE at Re = 400 and 13 500. A high instantaneous angle of attack at the stroke reversal results in high lift peak for 3-angle kinematics but its effect at Re = 400 and 13 500 is attenuated by strong vortical structures on the underside of the wing. Maximum PE is achieved at AR = 2.96, as a low AR wing does not produce enough lift and high AR wings consume more aerodynamic power. Although the lift is maximized using high r 1 ¯ and AR wings, our results show that low r 1 ¯ and high AR wings are best for maximizing PE for a given lift in insects.

  3. Variable-complexity aerodynamic optimization of an HSCT wing using structural wing-weight equations

    Science.gov (United States)

    Hutchison, M. G.; Unger, E. R.; Mason, W. H.; Grossman, B.; Haftka, R. T.

    1992-01-01

    A new approach for combining conceptual and preliminary design techniques for wing optimization is presented for the high-speed civil transport (HSCT). A wing-shape parametrization procedure is developed which allows the linking of planform and airfoil design variables. Variable-complexity design strategies are used to combine conceptual and preliminary-design approaches, both to preserve interdisciplinary design influences and to reduce computational expense. In the study, conceptual-design-level algebraic equations are used to estimate aircraft weight, supersonic wave drag, friction drag and drag due to lift. The drag due to lift and wave drag are also evaluated using more detailed, preliminary-design-level techniques. The methodology is applied to the minimization of the gross weight of an HSCT that flies at Mach 3.0 with a range of 6500 miles.

  4. Degree-degree correlations in random graphs with heavy-tailed degrees

    NARCIS (Netherlands)

    Litvak, Nelli; van der Hofstad, Remco

    2012-01-01

    We investigate degree-degree correlations for scale-free graph sequences. The main conclusion of this paper is that the assortativity coefficient is not the appropriate way to describe degree-dependences in scale-free random graphs. Indeed, we study the infinite volume limit of the assortativity

  5. Degree-degree correlations in random graphs with heavy-tailed degrees

    NARCIS (Netherlands)

    Litvak, Nelli; van der Hofstad, Remco

    2012-01-01

    We investigate degree-degree correlations for scale-free graph sequences. The main conclusion of this paper is that the assortativity coefficient is not the appropriate way to describe degree-dependences in scale-free random graphs. Indeed, we study the infinite volume limit of the assortativity coe

  6. Numerical Wing/Store Interaction Analysis of a Parametric F16 Wing

    OpenAIRE

    Cattarius, Jens

    1999-01-01

    A new numerical methodology to examine fluid-structure interaction of a wing/pylon/store system has been developed. The aeroelastic equation of motion of the complete system is solved iteratively in the time domain using a two-entity numerical code comprised of ABAQUS/Standard and the Unsteady-Vortex-Lattice Method. Both codes communicate through an iterative handshake procedure during which displacements and air loads are updated. For each increment in time the force/displacement equilibriu...

  7. Digital Morphing Wing: Active Wing Shaping Concept Using Composite Lattice-Based Cellular Structures

    Science.gov (United States)

    Jenett, Benjamin; Calisch, Sam; Cellucci, Daniel; Cramer, Nick; Gershenfeld, Neil; Swei, Sean

    2017-01-01

    Abstract We describe an approach for the discrete and reversible assembly of tunable and actively deformable structures using modular building block parts for robotic applications. The primary technical challenge addressed by this work is the use of this method to design and fabricate low density, highly compliant robotic structures with spatially tuned stiffness. This approach offers a number of potential advantages over more conventional methods for constructing compliant robots. The discrete assembly reduces manufacturing complexity, as relatively simple parts can be batch-produced and joined to make complex structures. Global mechanical properties can be tuned based on sub-part ordering and geometry, because local stiffness and density can be independently set to a wide range of values and varied spatially. The structure's intrinsic modularity can significantly simplify analysis and simulation. Simple analytical models for the behavior of each building block type can be calibrated with empirical testing and synthesized into a highly accurate and computationally efficient model of the full compliant system. As a case study, we describe a modular and reversibly assembled wing that performs continuous span-wise twist deformation. It exhibits high performance aerodynamic characteristics, is lightweight and simple to fabricate and repair. The wing is constructed from discrete lattice elements, wherein the geometric and mechanical attributes of the building blocks determine the global mechanical properties of the wing. We describe the mechanical design and structural performance of the digital morphing wing, including their relationship to wind tunnel tests that suggest the ability to increase roll efficiency compared to a conventional rigid aileron system. We focus here on describing the approach to design, modeling, and construction as a generalizable approach for robotics that require very lightweight, tunable, and actively deformable structures. PMID:28289574

  8. Graduate Physics Degrees: Largest Departments and Degree Distribution. Focus On

    Science.gov (United States)

    Mulvey, Patrick J.; Nicholson, Starr

    2014-01-01

    In the 2011-12 academic year there were 751 degree-granting physics departments in the U.S. Of these, 195 offered a PhD and 62 departments offered a master's as the highest physics degree. The remaining 494 departments offered a bachelor's as their highest physics degree. There were six universities that had two doctoral-granting physics…

  9. Geometric design of the best performing auto-rotating wing

    Science.gov (United States)

    Liu, Yucen; Vincent, Lionel; Kanso, Eva

    2016-11-01

    Many plants use gravity and aerodynamics to disperse their seeds away from the parent plant. Various seed designs result in different dispersal modes from gliding to auto-rotating. Here, we are interested in understanding the effect of geometric design of auto-rotating seedpods on their aerodynamic performance. As an experimentally tractable surrogate to real seedpods, we investigate auto-rotating paper wings of various shape designs. We compare these designs to a control case consisting of the canonical rectangular wing. Inspired by aerodynamics, we begin by considering the benefit of an elliptical planform, and test the effect of aspect ratio on flight range and descent angle. We find the elliptical planform improves the tumbling rate and the aspect ratio has a positive effect on the flight performance of the wings. We then test two families of more complex shapes: one of tapered planform and one of a planform with sharp tips. We look for an optimal flight performance while constraining either the mass or the maximum length and width of the wing. We find that wings with sharper tips and larger length have higher auto-rotation rates and improved performance. The results imply that both the planform and length of the wing contribute to the wing's flight performance.

  10. Modeling the Motion of a Flapping Wing Aerial Vehicle

    Directory of Open Access Journals (Sweden)

    Vorochaeva L.Y.

    2017-01-01

    Full Text Available The article discusses the vertical flight of a flapping wing aerial vehicle, which is also called an ornithopter. The robot is a chain of five links connected in series by active cylindrical hinges with the central link being the body and the remainder forming folding wings in pairs. The distinctive feature of this device is that the flaps of its wings imitate those of a seagull i.e. the device has a biological prototype. We construct a mathematical model of this device; much attention is given to the model of the interaction of the wings with the air environment and we determine the positions and velocities of points of application of the reduced aerodynamic forces to each of the links. Based on the results of numerical modelling of the vertical flight of the robot three modes of flight were established: ascent, hovering at a certain height and descent. The device can operate in these modes based on the oscillation parameters of the wings in particular flapping frequency and amplitude, the ratio of the amplitudes of two links and one wing and the shift of the equilibrium oscillation position of the wings relative to zero.

  11. Turbulent Flow Over a Low-Camber Pitching Arc Wing

    Science.gov (United States)

    Molki, Majid

    2014-11-01

    Aerodynamics of pitching airfoils and wings are of great importance to the design of air vehicles. This investigation presents the effect of camber on flow field and force coefficient for a pitching circular-arc airfoil. The wing considered in this study is a cambered plate of zero thickness which executes a linear pitch ramp, hold and return of 45° amplitude. The momentum equation is solved on a mesh that is attached to the wing and executes a pitching motion with the wing about a pivot point located at 0.25-chord or 0.50-chord distance from the leading edge. Turbulence is modeled by the k - ω SST model. Using the open-source software OpenFOAM, the conservation equations are solved on a dynamic mesh and the flow is resolved all the way to the wall (y+ ~ 1). The computations are performed for Re = 40,000 with the reduced pitch rate equal to K = cθ˙ / 2U∞ = 0 . 2 . The results are presented for three wings, namely, a flat plate (zero camber) and wings of 4% and 10% camber. It is found that the flow has complex features such as leading-edge vortex, near-wake vortex pairs, clockwise and counter-clockwise vortices, and trailing-edge vortex. While vortices are formed over the flat plate, they are formed both over and under the cambered wing.

  12. Aerodynamics and flight performance of flapping wing micro air vehicles

    Science.gov (United States)

    Silin, Dmytro

    Research efforts in this dissertation address aerodynamics and flight performance of flapping wing aircraft (ornithopters). Flapping wing aerodynamics was studied for various wing sizes, flapping frequencies, airspeeds, and angles of attack. Tested wings possessed both camber and dihedral. Experimental results were analyzed in the framework of momentum theory. Aerodynamic coefficients and Reynolds number are defined using a reference velocity as a vector sum of a freestream velocity and a strokeaveraged wingtip velocity. No abrupt stall was observed in flapping wings for the angle of attack up to vertical. If was found that in the presence of a freestream lift of a flapping wing in vertical position is higher than the propulsive thrust. Camber and dihedral increased both lift and thrust. Lift-curve slope, and maximum lift coefficient increased with Reynolds number. Performance model of an ornithopter was developed. Parametric studies of steady level flight of ornithopters with, and without a tail were performed. A model was proposed to account for wing-sizing effects during hover. Three micro ornithopter designs were presented. Ornithopter flight testing and data-logging was performed using a telemetry acquisition system, as well as motion capture technology. The ability of ornithopter for a sustained flight and a presence of passive aerodynamic stability were shown. Flight data were compared with performance simulations. Close agreement in terms of airspeed and flapping frequency was observed.

  13. The design and testing of subscale smart aircraft wing bolts

    Science.gov (United States)

    Vugampore, J. M. V.; Bemont, C.

    2012-07-01

    Presently costly periodic inspection is vital in guaranteeing the structural integrity of aircraft. This investigation assesses the potential for significantly reducing aircraft maintenance costs without modification of aircraft structures by implementing smart wing bolts, manufactured from TRIP steel, which can be monitored for damage in situ. TRIP steels undergo a transformation from paramagnetic austenite to ferromagnetic martensite during deformation. Subscale smart aircraft wing bolts were manufactured from hot rolled TRIP steel. These wing bolts were used to demonstrate that washers incorporating embedded inductance coils can be utilized to measure the martensitic transformation occurring in the TRIP steel during bolt deformation. Early in situ warning of a critical bolt stress level was thereby facilitated, potentially reducing the costly requirement for periodic wing bolt removal and inspection. The hot rolled TRIP steels that were utilized in these subscale bolts do not however exhibit the mechanical properties required of wing bolt material. Thus warm rolled TRIP steel alloys were also investigated. The mechanical properties of the best warm rolled TRIP steel alloy tested almost matched those of AISI 4340. The warm rolled alloys were also shown to exhibit transformation before yield, allowing for earlier warning when overload occurs. Further work will be required relating to fatigue crack detection, environmental temperature fluctuation and more thorough material characterization. However, present results show that in situ early detection of wing bolt overload is feasible via the use of high alloy warm rolled TRIP steel wing bolts in combination with inductive sensor embedded washers.

  14. Static Aeroelastic Effects of Formation Flight for Slender Unswept Wings

    Science.gov (United States)

    Hanson, Curtis E.

    2009-01-01

    The static aeroelastic equilibrium equations for slender, straight wings are modified to incorporate the effects of aerodynamically-coupled formation flight. A system of equations is developed by applying trim constraints and is solved for component lift distribution, trim angle-of-attack, and trim aileron deflection. The trim values are then used to calculate the elastic twist distribution of the wing box. This system of equations is applied to a formation of two gliders in trimmed flight. Structural and aerodynamic properties are assumed for the gliders, and solutions are calculated for flexible and rigid wings in solo and formation flight. It is shown for a sample application of two gliders in formation flight, that formation disturbances produce greater twist in the wingtip immersed in the vortex than for either the opposing wingtip or the wings of a similar airplane in solo flight. Changes in the lift distribution, resulting from wing twist, increase the performance benefits of formation flight. A flexible wing in formation flight will require greater aileron deflection to achieve roll trim than a rigid wing.

  15. Rib for blended wing-body aircraft

    Science.gov (United States)

    Hawley, Arthur V. (Inventor)

    1999-01-01

    Structural ribs for providing structural support for a structure, such as the pressure cabin of a blended-wing body aircraft. In a first embodiment, the ribs are generally Y-shaped, being comprised of a vertical web and a pair of inclined webs attached to the vertical web to extend upwardly and outwardly from the vertical web in different directions, with only the upper edges of the inclined webs being attached to a structural element. In a second embodiment, the ribs are generally trident-shaped, whereby the vertical web extends upwardly beyond the intersection of the inclined webs with the vertical web, with the upper edge of the vertical web as well as the upper edges of the inclined webs being attached to the same structural element.

  16. Prediction of Wing Downwash Using CFD

    Directory of Open Access Journals (Sweden)

    Mohammed MAHDI

    2015-06-01

    Full Text Available Wing downwash study and estimation of downwash effect on the tail plane is an important task during the aircraft design process, although a lot of papers and works has been done, but the experimental work is the most important, the progress in CFD simulation has reached to the point it is able to reduce the number of runs in the wind tunnel. In this work CFD has been utilized to calculate the downwash angle and downwash gradient with respect to the angle of attack over a high aspect ratio of a typical UAV. The results of the simulation shall be used in the estimation and calculation of the longitudinal static stability analysis of the UAV.

  17. Supersonic Wing Optimization Using SpaRibs

    Science.gov (United States)

    Locatelli, David; Mulani, Sameer B.; Liu, Qiang; Tamijani, Ali Y.; Kapania, Rakesh K.

    2014-01-01

    This research investigates the advantages of using curvilinear spars and ribs, termed SpaRibs, to design a supersonic aircraft wing-box in comparison to the use of classic design concepts that employ straight spars and ribs. The objective is to achieve a more efficient load-bearing mechanism and to passively control the deformation of the structure under the flight loads. Moreover, the use of SpaRibs broadens the design space and allows for natural frequencies and natural mode shape tailoring. The SpaRibs concept is implemented in a new optimization MATLAB-based framework referred to as EBF3SSWingOpt. This optimization scheme performs both the sizing and the shaping of the internal structural elements, connecting the optimizer with the analysis software. The shape of the SpaRibs is parametrically defined using the so called Linked Shape method. Each set of SpaRibs is placed in a one by one square domain of the natural space. The set of curves is subsequently transformed in the physical space for creating the wing structure geometry layout. The shape of each curve of each set is unique; however, mathematical relations link the curvature in an effort to reduce the number of design variables. The internal structure of a High Speed Commercial Transport aircraft concept developed by Boeing is optimized subjected to stress, subsonic flutter and supersonic flutter constraints. The results show that the use of the SpaRibs allows for the reduction of the aircraft's primary structure weight without violating the constraints. A weight reduction of about 15 percent is observed.

  18. Butterfly wing coloration studied with a novel imaging scatterometer

    Science.gov (United States)

    Stavenga, Doekele

    2010-03-01

    Animal coloration functions for display or camouflage. Notably insects provide numerous examples of a rich variety of the applied optical mechanisms. For instance, many butterflies feature a distinct dichromatism, that is, the wing coloration of the male and the female differ substantially. The male Brimstone, Gonepteryx rhamni, has yellow wings that are strongly UV iridescent, but the female has white wings with low reflectance in the UV and a high reflectance in the visible wavelength range. In the Small White cabbage butterfly, Pieris rapae crucivora, the wing reflectance of the male is low in the UV and high at visible wavelengths, whereas the wing reflectance of the female is higher in the UV and lower in the visible. Pierid butterflies apply nanosized, strongly scattering beads to achieve their bright coloration. The male Pipevine Swallowtail butterfly, Battus philenor, has dorsal wings with scales functioning as thin film gratings that exhibit polarized iridescence; the dorsal wings of the female are matte black. The polarized iridescence probably functions in intraspecific, sexual signaling, as has been demonstrated in Heliconius butterflies. An example of camouflage is the Green Hairstreak butterfly, Callophrys rubi, where photonic crystal domains exist in the ventral wing scales, resulting in a matte green color that well matches the color of plant leaves. The spectral reflection and polarization characteristics of biological tissues can be rapidly and with unprecedented detail assessed with a novel imaging scatterometer-spectrophotometer, built around an elliptical mirror [1]. Examples of butterfly and damselfly wings, bird feathers, and beetle cuticle will be presented. [4pt] [1] D.G. Stavenga, H.L. Leertouwer, P. Pirih, M.F. Wehling, Optics Express 17, 193-202 (2009)

  19. The morphological basis of the arm-to-wing transition.

    Science.gov (United States)

    Poore, Samuel O

    2008-02-01

    Human-powered flight has fascinated scientists, artists, and physicians for centuries. This history includes Abbas Ibn Firnas, a Spanish inventor who attempted the first well-documented human flight; Leonardo da Vinci and his flying machines; the Turkish inventor Hezarfen Ahmed Celebi; and the modern aeronautical pioneer Otto Lilienthal. These historic figures held in common their attempts to construct wings from man-made materials, and though their human-powered attempts at flight never came to fruition, the ideas and creative elements contained within their flying machines were essential to modern aeronautics. Since the time of these early pioneers, flight has continued to captivate humans, and recently, in a departure from creating wings from artificial elements, there has been discussion of using reconstructive surgery to fabricate human wings from human arms. This article is a descriptive study of how one might attempt such a reconstruction and in doing so calls upon essential evidence in the evolution of flight, an understanding of which is paramount to constructing human wings from arms. This includes a brief analysis and exploration of the anatomy of the 150-million-year-old fossil Archaeopteryx lithographica, with particular emphasis on the skeletal organization of this primitive bird's wing and wrist. Additionally, certain elements of the reconstruction must be drawn from an analysis of modern birds including a description of the specialized shoulder of the European starling, Sturnus vulgaris. With this anatomic description in tow, basic calculations regarding wing loading and allometry suggest that human wings would likely be nonfunctional. However, with the proper reconstructive balance between primitive (Archaeopteryx) and modern (Sturnus), and in attempting to integrate a careful analysis of bird anatomy with modern surgical techniques, the newly constructed human wings could function as cosmetic features simulating, for example, the nonfunctional

  20. A blended wing body airplane with a close-coupled, tilting tail

    Science.gov (United States)

    Nasir, R. E. M.; Mazlan, N. S. C.; Ali, Z. M.; Wisnoe, W.; Kuntjoro, W.

    2016-10-01

    This paper highlights a novel approach to stabilizing and controlling pitch and yaw motion via a set of horizontal tail that can act as elevator and rudder. The tail is incorporated into a new design of blended wing body (BWB) aircraft, known as Baseline-V, located just aft of the trailing edge of its inboard wing. The proposed close-coupled tail is equipped with elevators that deflect in unison, and can tilt - an unusual means of tilting where if starboard side is tilted downward at k degree, and then the portside must be tilted upward at k degree too. A wind tunnel experiment is conducted to investigate aerodynamics and static stability of Baseline-V BWB aircraft. The model is being tested at actual flight speed of 15 m/s (54 km/h) with varying angle of attack for five elevator angle cases at zero tilt angle and varying sideslip angle for four tilt angle cases at one fixed elevator angle. The result shows that the aircraft's highest lift-to-drag ratio is 32. It is also found that Baseline-V is statically stable in pitch and yaw but has no clear indication in terms of roll stability.

  1. Winging of scapula due to serratus anterior tear

    Directory of Open Access Journals (Sweden)

    Varun Singh Kumar

    2014-10-01

    Full Text Available 【Abstract】Winging of scapula occurs most commonly due to injury to long thoracic nerve supplying serratus anterior muscle. Traumatic injury to serratus anterior muscle itself is very rare. We reported a case of traumatic winging of scapula due to tear of serratus anterior muscle in a 19-year-old male. Winging was present in neutral position and in extension of right shoulder joint but not on "push on wall" test. Patient was managed conservatively and achieved satisfactory result. Key words: Serratus anterior tear; Scapula; Wounds and injuries

  2. Laminar-turbulent transition on the flying wing model

    Science.gov (United States)

    Pavlenko, A. M.; Zanin, B. Yu.; Katasonov, M. M.

    2016-10-01

    Results of an experimental study of a subsonic flow past aircraft model having "flying wing" form and belonging to the category of small-unmanned aerial vehicles are reported. Quantitative data about the structure of the flow near the model surface were obtained by hot-wire measurements. It was shown, that with the wing sweep angle 34 °the laminar-turbulent transition scenario is identical to the one on a straight wing. The transition occurs through the development of a package of unstable oscillations in the boundary layer separation.

  3. Static measurements of slender delta wing rolling moment hysteresis

    Science.gov (United States)

    Katz, Joseph; Levin, Daniel

    1991-01-01

    Slender delta wing planforms are susceptible to self-induced roll oscillations due to aerodynamic hysteresis during the limit cycle roll oscillation. Test results are presented which clearly establish that the static rolling moment hysteresis has a damping character; hysteresis tends to be greater when, due to either wing roll or side slip, the vortex burst moves back and forth over the wing trailing edge. These data are an indirect indication of the damping role of the vortex burst during limit cycle roll oscillations.

  4. Structural Health Monitoring Analysis for the Orbiter Wing Leading Edge

    Science.gov (United States)

    Yap, Keng C.

    2010-01-01

    This viewgraph presentation reviews Structural Health Monitoring Analysis for the Orbiter Wing Leading Edge. The Wing Leading Edge Impact Detection System (WLE IDS) and the Impact Analysis Process are also described to monitor WLE debris threats. The contents include: 1) Risk Management via SHM; 2) Hardware Overview; 3) Instrumentation; 4) Sensor Configuration; 5) Debris Hazard Monitoring; 6) Ascent Response Summary; 7) Response Signal; 8) Distribution of Flight Indications; 9) Probabilistic Risk Analysis (PRA); 10) Model Correlation; 11) Impact Tests; 12) Wing Leading Edge Modeling; 13) Ascent Debris PRA Results; and 14) MM/OD PRA Results.

  5. Bioinspired ultraviolet reflective photonic structures derived from butterfly wings (Euploea)

    Science.gov (United States)

    Song, Fang; Su, Huilan; Chen, Jianjun; Zhang, Di; Moon, Won-Jin

    2011-10-01

    Butterfly wings have been demonstrated to have potential applications in various optical devices. For complementarily, we extend them to ultraviolet (UV) reflectors, inspired by the UV reflective photonic structures that have been evolved to satisfy UV communication systems of butterflies. UV reflective photonic structures of butterfly wings were replicated in multiscale, and thus endowed the resultant SnO2 materials with enhanced UV reflection. This biomimetic strategy provides us a universal way towards UV reflectors without changing the chemical compositions. Furthermore, the UV reflection could be potentially tuned by choosing different photonic structures of butterfly wings and other bio-species.

  6. Comparison of Radical Right-Wing Parties in Bulgaria and Romania: The National Movement of Ataka and the Great Romania Party

    Directory of Open Access Journals (Sweden)

    Markéta Smrčková

    2009-04-01

    Full Text Available This paper focuses on a comparison of two radical right-wing parties, Ataka and the Great Romania Party, their positions in the national party system, and their relationships with the governing parties as well as with other national right-wing parties. In this essay the party programmes, electorate, attitude to minorities, and degree of nationalism will be compared. Another important part of this paper is comparison of the election results of these parties and their chances of remaining in the national parliaments (and thus becoming a crucial part of party system. All the details mentioned above will be analyzed against the background of theories of radical right-wing parties.

  7. OmegaWINGS: spectroscopy in the outskirts of local clusters of galaxies

    Science.gov (United States)

    Moretti, A.; Gullieuszik, M.; Poggianti, B.; Paccagnella, A.; Couch, W. J.; Vulcani, B.; Bettoni, D.; Fritz, J.; Cava, A.; Fasano, G.; D'Onofrio, M.; Omizzolo, A.

    2017-03-01

    Context. Studies of the properties of low-redshift cluster galaxies suffer, in general, from small spatial coverage of the cluster area. WINGS, the most homogeneous and complete study of galaxies in dense environments to date, obtained spectroscopic redshifts for 48 clusters at a median redshift of 0.05, out to an average distance of approximately 0.5 cluster virial radii. The WINGS photometric survey was recently extended by the VST survey OmegaWINGS to cover the outskirts of a subset of the original cluster sample. Aims: In this work, we present the spectroscopic follow-up of 33 of the 46 clusters of galaxies observed with VST over 1 square degree. The aim of this spectroscopic survey is to enlarge the number of cluster members and study the galaxy characteristics and the cluster dynamical properties out to large radii, reaching the virial radius and beyond. Methods: We used the AAOmega spectrograph at AAT to obtain fiber-integrated spectra covering the wavelength region between 3800 and 9000 Å with a spectral resolution of 3.5-6 Å full width at half maximum (FWHM). Observations were performed using two different configurations and exposure times per cluster. We measured redshifts using both absorption and emission lines and used them to derive the cluster redshifts and velocity dispersions. Results: We present here the redshift measurements for 17 985 galaxies, 7497 of which turned out to be cluster members. The sample magnitude completeness is 80% at V = 20. Thanks to the observing strategy, the radial completeness turned out to be relatively constant (90%) within the AAOmega field of view. The success rate in measuring redshifts is 95%, at all radii. Conclusions: We provide redshifts for the full sample of galaxies in OmegaWINGS clusters together with updated and robust cluster redshift and velocity dispersions. These data, publicly accessible through the CDS and VO archives, will enable evolutionary and environmental studies of cluster properties, providing

  8. Fruit flies modulate passive wing pitching to generate in-flight turns

    CERN Document Server

    Bergou, Attila J; Guckenheimer, John; Cohen, Itai; Wang, Z Jane

    2009-01-01

    Flying insects execute aerial maneuvers through subtle manipulations of their wing motions. Here, we measure the free flight kinematics of fruit flies and determine how they modulate their wing pitching to induce sharp turns. By analyzing the torques these insects exert to pitch their wings, we infer that the wing hinge acts as a torsional spring that passively resists the wing's tendency to flip in response to aerodynamic and inertial forces. To turn, the insects asymmetrically change the spring rest angles to generate rowing motions of their wings. Thus, insects can generate these maneuvers using only a slight active actuation that biases their wing motion.

  9. Degree Depreciation: A Fait Accompli for the Liberal Arts Degree

    Science.gov (United States)

    Duplass, James A.

    1976-01-01

    The liberal arts degree will continue to lack the credibility needed to compete with professional school degrees in the job market unless a return is made to rigourous standards, subjective tests, term papers, comprehensive exams, improvement in instructional methods, and more stringent curriculum requirements for foreign language, composition,…

  10. A Model for Selection of Eyespots on Butterfly Wings.

    Directory of Open Access Journals (Sweden)

    Toshio Sekimura

    Full Text Available The development of eyespots on the wing surface of butterflies of the family Nympalidae is one of the most studied examples of biological pattern formation.However, little is known about the mechanism that determines the number and precise locations of eyespots on the wing. Eyespots develop around signaling centers, called foci, that are located equidistant from wing veins along the midline of a wing cell (an area bounded by veins. A fundamental question that remains unsolved is, why a certain wing cell develops an eyespot, while other wing cells do not.We illustrate that the key to understanding focus point selection may be in the venation system of the wing disc. Our main hypothesis is that changes in morphogen concentration along the proximal boundary veins of wing cells govern focus point selection. Based on previous studies, we focus on a spatially two-dimensional reaction-diffusion system model posed in the interior of each wing cell that describes the formation of focus points. Using finite element based numerical simulations, we demonstrate that variation in the proximal boundary condition is sufficient to robustly select whether an eyespot focus point forms in otherwise identical wing cells. We also illustrate that this behavior is robust to small perturbations in the parameters and geometry and moderate levels of noise. Hence, we suggest that an anterior-posterior pattern of morphogen concentration along the proximal vein may be the main determinant of the distribution of focus points on the wing surface. In order to complete our model, we propose a two stage reaction-diffusion system model, in which an one-dimensional surface reaction-diffusion system, posed on the proximal vein, generates the morphogen concentrations that act as non-homogeneous Dirichlet (i.e., fixed boundary conditions for the two-dimensional reaction-diffusion model posed in the wing cells. The two-stage model appears capable of generating focus point distributions

  11. On the colour of wing scales in butterflies: iridescence and preferred orientation of single gyroid photonic crystals

    Science.gov (United States)

    2017-01-01

    Lycaenid butterflies from the genera Callophrys, Cyanophrys and Thecla have evolved remarkable biophotonic gyroid nanostructures within their wing scales that have only recently been replicated by nanoscale additive manufacturing. These nanostructures selectively reflect parts of the visible spectrum to give their characteristic non-iridescent, matte-green appearance, despite a distinct blue–green–yellow iridescence predicted for individual crystals from theory. It has been hypothesized that the organism must achieve its uniform appearance by growing crystals with some restrictions on the possible distribution of orientations, yet preferential orientation observed in Callophrys rubi confirms that this distribution need not be uniform. By analysing scanning electron microscope and optical images of 912 crystals in three wing scales, we find no preference for their rotational alignment in the plane of the scales. However, crystal orientation normal to the scale was highly correlated to their colour at low (conical) angles of view and illumination. This correlation enabled the use of optical images, each containing up to 104–105 crystals, for concluding the preferential alignment seen along the at the level of single scales, appears ubiquitous. By contrast, orientations were found to occur at no greater rate than that expected by chance. Above a critical cone angle, all crystals reflected bright green light indicating the dominant light scattering is due to the predicted band gap along the direction, independent of the domain orientation. Together with the natural variation in scale and wing shapes, we can readily understand the detailed mechanism of uniform colour production and iridescence suppression in these butterflies. It appears that the combination of preferential alignment normal to the wing scale, and uniform distribution within the plane is a near optimal solution for homogenizing the angular distribution of the band gap relative to the wings. Finally

  12. Micro-Scale Flapping Wings for the Advancement of Flying MEMS

    Science.gov (United States)

    2009-03-01

    wings. These devices are often called entomopters, winged in- sect machines, or ornithopter , winged bird machines. The flapping wing benefits from both...minutes of flight before refueling is required [26–28]. An ornithopter from Tamkang University was reviewed. It was constructed using titanium alloy...Grasmeyer, Y. C. Tai, C. M. Ho, and M. Keennon, “Mems wing technology for a battery-powered ornithopter ,” Proceedings of the IEEE Micro Electro Mechanical

  13. Celebrating 100 Years of Flight: Testing Wing Designs in Aircraft

    Science.gov (United States)

    Pugalee, David K.; Nusinov, Chuck; Giersch, Chris; Royster, David; Pinelli, Thomas E.

    2005-01-01

    This article describes an investigation involving several designs of airplane wings in trial flight simulations based on a NASA CONNECT program. Students' experiences with data collection and interpretation are highlighted. (Contains 5 figures.)

  14. Lift estimation of Half-Rotating Wing in hovering flight

    Science.gov (United States)

    Wang, X. Y.; Dong, Y. P.; Qiu, Z. Z.; Zhang, Y. Q.; Shan, J. H.

    2016-11-01

    Half-Rotating Wing (HRW) is a new kind of flapping wing system with rotating flapping instead of oscillating flapping. Estimating approach of hovering lift which generated in hovering flight was important theoretical foundation to design aircraft using HRW. The working principle of HRW based on Half-Rotating Mechanism (HRM) was firstly introduced in this paper. Generating process of lift by HRW was also given. The calculating models of two lift mechanisms for HRW, including Lift of Flow Around Wing (LFAW) and Lift of Flow Dragging Wing (LFDW), were respectively established. The lift estimating model of HRW was further deduced, by which hovering lift for HRW with different angular velocity could be calculated. Case study using XFLOW software simulation indicates that the above estimating method was effective and feasible to predict roughly the hovering lift for a new HRW system.

  15. Variable camber wing based on pneumatic artificial muscles

    Science.gov (United States)

    Yin, Weilong; Liu, Libo; Chen, Yijin; Leng, Jinsong

    2009-07-01

    As a novel bionic actuator, pneumatic artificial muscle has high power to weight ratio. In this paper, a variable camber wing with the pneumatic artificial muscle is developed. Firstly, the experimental setup to measure the static output force of pneumatic artificial muscle is designed. The relationship between the static output force and the air pressure is investigated. Experimental result shows the static output force of pneumatic artificial muscle decreases nonlinearly with increasing contraction ratio. Secondly, the finite element model of the variable camber wing is developed. Numerical results show that the tip displacement of the trailing-edge increases linearly with increasing external load and limited with the maximum static output force of pneumatic artificial muscles. Finally, the variable camber wing model is manufactured to validate the variable camber concept. Experimental result shows that the wing camber increases with increasing air pressure and that it compare very well with the FEM result.

  16. Winging of the scapula: An unusual complication of needle thoracocentesis.

    Science.gov (United States)

    Faruqi, S; Raychaudhuri, C; Thirumaran, M; Blaxill, P

    2008-07-01

    Needle thoracocentesis is a common interventional procedure and is generally considered to be safe. Major complications associated with this procedure are uncommon. Here we describe a rare instance of winging of the scapula following needle thoracocentesis.

  17. Gyroid cuticular structures in butterfly wing scales : biological photonic crystals

    NARCIS (Netherlands)

    Michielsen, K.; Stavenga, D. G.

    2008-01-01

    We present a systematic study of the cuticular structure in the butterfly wing scales of some papilionids (Parides sesostris and Teinopalpus imperialis) and lycaenids (Callophrys rubi, Cyanophrys remus, Mitoura gryneus and Callophrys dumetorum). Using published scanning and transmission electron mic

  18. Glaucous-winged gull nesting on Amchitka Island

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The glaucous-winged gull (Larus glaucescens) is the most common gull in the north Pacific (Bent 1921, Murie 1959). It is also one of the most abundant permanent...

  19. The efficient solution of transonic wing flow fields

    Science.gov (United States)

    Holst, T. L.; Subramanian, N. R.; Thomas, S. D.

    1983-01-01

    An evaluation of the transonic-wing-analysis computer code TWING is presented. TWING utilizes a fully implicit, approximate-factorization iteration scheme to solve the full-potential equation in conservative form. A numerical elliptic-solver grid-generation scheme is used to generate the required finite-difference mesh. Several wing configurations have been analyzed, and comparisons of computed results have been made with available experimental data. Results indicate that the code is robust, accurate (when significant viscous effects are not present), and efficient. TWING generally produces solutions an order of magnitude faster than other conservative, full-potential codes using successive-line overrelaxation. The present method is applicable to a wide range of isolated wing configurations, including high-aspect-ratio transport wings and low-aspect-ratio, high-sweep, fighter configurations.

  20. Recent applications of the transonic wing analysis computer code, TWING

    Science.gov (United States)

    Subramanian, N. R.; Holst, T. L.; Thomas, S. D.

    1982-01-01

    An evaluation of the transonic-wing-analysis computer code TWING is given. TWING utilizes a fully implicit approximate factorization iteration scheme to solve the full potential equation in conservative form. A numerical elliptic-solver grid-generation scheme is used to generate the required finite-difference mesh. Several wing configurations were analyzed, and the limits of applicability of this code was evaluated. Comparisons of computed results were made with available experimental data. Results indicate that the code is robust, accurate (when significant viscous effects are not present), and efficient. TWING generally produces solutions an order of magnitude faster than other conservative full potential codes using successive-line overrelaxation. The present method is applicable to a wide range of isolated wing configurations including high-aspect-ratio transport wings and low-aspect-ratio, high-sweep, fighter configurations.

  1. New findings of twisted-wing parasites (Strepsiptera) in Alaska

    Science.gov (United States)

    Mcdermott, Molly

    2016-01-01

    Strepsipterans are a group of insects with a gruesome life history and an enigmatic evolutionary past. Called ‘twisted-wing parasites’, they are minute parasitoids with a very distinct morphology (Figure 1). Alternatively thought to be related to ichneumon wasps, Diptera (flies), Coleoptera (beetles), and even Neuroptera (net-winged insects) (Pohl and Beutel, 2013); the latest genetic and morphological data support the sister order relationship of Strepsiptera and Coleoptera (Niehuis et al., 2012). Strepsipterans are highly modified, males having two hind wings and halteres instead of front wings or elytra. Unlike most parasitoids, they develop inside active, living insects who are sexually sterilized but not killed until or after emergence (Kathirithamby et al., 2015).

  2. Silent and Efficient Supersonic Bi-Directional Flying Wing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose a Phase I study for a novel concept of a supersonic bi-directional (SBiDir) flying wing (FW) that has the potential to revolutionize supersonic flight...

  3. Research Degrees as Professional Education?

    Science.gov (United States)

    Barnacle, Robyn; Dall'Alba, Gloria

    2011-01-01

    There is an increasing trend within higher education and, more specifically, in higher degrees by research, to treat a professional skills set as a desirable graduate outcome. The increasing value that is being placed on a professional skills set in large part reflects growing interest around the world in the role of research degrees in labour…

  4. Wings of the butterfly: Sunspot groups for 1826-2015

    Science.gov (United States)

    Leussu, R.; Usoskin, I. G.; Senthamizh Pavai, V.; Diercke, A.; Arlt, R.; Denker, C.; Mursula, K.

    2017-03-01

    The spatio-temporal evolution of sunspot activity, the so-called Maunder butterfly diagram, has been continously available since 1874 using data from the Royal Greenwich Observatory, extended by SOON network data after 1976. Here we present a new extended butterfly diagram of sunspot group occurrence since 1826, using the recently digitized data from Schwabe (1826-1867) and Spörer (1866-1880). The wings of the diagram are separated using a recently developed method based on an analysis of long gaps in sunspot group occurrence in different latitude bands. We define characteristic latitudes, corresponding to the start, end, and the largest extent of the wings (the F, L, and H latitudes). The H latitudes (30°-45°) are highly significantly correlated with the strength of the wings (quantified by the total sum of the monthly numbers of sunspot groups). The F latitudes (20°-30°) depict a weak tendency, especially in the southern hemisphere, to follow the wing strength. The L latitudes (2°-10°) show no clear relation to the wing strength. Overall, stronger cycle wings tend to start at higher latitudes and have a greater wing extent. A strong (5-6)-cycle periodic oscillation is found in the start and end times of the wings and in the overlap and gaps between successive wings of one hemisphere. While the average wing overlap is zero in the southern hemisphere, it is two to three months in the north. A marginally significant oscillation of about ten solar cycles is found in the asymmetry of the L latitudes. The new long database of butterfly wings provides new observational constraints to solar dynamo models that discuss the spatio-temporal distribution of sunspot occurrence over the solar cycle and longer. Digital data for Fig. 1 are available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (http://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/599/A131

  5. Comparative Analysis of Uninhibited and Constrained Avian Wing Aerodynamics

    Science.gov (United States)

    Cox, Jordan A.

    The flight of birds has intrigued and motivated man for many years. Bird flight served as the primary inspiration of flying machines developed by Leonardo Da Vinci, Otto Lilienthal, and even the Wright brothers. Avian flight has once again drawn the attention of the scientific community as unmanned aerial vehicles (UAV) are not only becoming more popular, but smaller. Birds are once again influencing the designs of aircraft. Small UAVs operating within flight conditions and low Reynolds numbers common to birds are not yet capable of the high levels of control and agility that birds display with ease. Many researchers believe the potential to improve small UAV performance can be obtained by applying features common to birds such as feathers and flapping flight to small UAVs. Although the effects of feathers on a wing have received some attention, the effects of localized transient feather motion and surface geometry on the flight performance of a wing have been largely overlooked. In this research, the effects of freely moving feathers on a preserved red tailed hawk wing were studied. A series of experiments were conducted to measure the aerodynamic forces on a hawk wing with varying levels of feather movement permitted. Angle of attack and air speed were varied within the natural flight envelope of the hawk. Subsequent identical tests were performed with the feather motion constrained through the use of externally-applied surface treatments. Additional tests involved the study of an absolutely fixed geometry mold-and-cast wing model of the original bird wing. Final tests were also performed after applying surface coatings to the cast wing. High speed videos taken during tests revealed the extent of the feather movement between wing models. Images of the microscopic surface structure of each wing model were analyzed to establish variations in surface geometry between models. Recorded aerodynamic forces were then compared to the known feather motion and surface

  6. Bristles reduce force required to fling wings apart in small insects

    Science.gov (United States)

    Jones, Shannon; Yun, Young; Hedrick, Tyson; Griffith, Boyce; Miller, Laura

    2016-11-01

    The smallest flying insects commonly possess wings with long bristles. Little quantitative information is available on the morphology of these bristles, and the functional importance of these bristles remains a mystery. In this study, we used the immersed boundary method to determine via numerical simulation if bristled wings reduced the force required to fling the wings apart during "clap and fling". The challenge of studying the fluid dynamics of bristles was in resolving the fluid flow between the bristles. The effects of Reynolds number, angle of attack, bristle spacing, and wing-wing interactions were investigated. We found that a bristled wing experiences less force than a solid wing, however bristled wings may act more like solid wings at lower angles of attack than they do at higher angles of attack. In wing-wing interactions, bristled wings significantly decrease the drag required to fling two wings apart compared with solid wings, especially at lower Reynolds numbers. These results support the idea that bristles may offer an aerodynamic benefit during clap and fling by reducing the force required to fling the wings apart in tiny insects.

  7. The mappings of degree 1

    Directory of Open Access Journals (Sweden)

    2006-01-01

    Full Text Available The maps of the form f( x = ∑ i=1 n a i ⋅x⋅ b i , called 1-degree maps, are introduced and investigated. For noncommutative algebras and modules over them 1-degree maps give an analogy of linear maps and differentials. Under some conditions on the algebra 𝒜 , contractibility of the group of 1-degree isomorphisms is proved for the module l 2 ( 𝒜 . It is shown that these conditions are fulfilled for the algebra of linear maps of a finite-dimensional linear space. The notion of 1-degree map gives a possibility to define a nonlinear Fredholm map of l 2 ( 𝒜 and a Fredholm manifold modelled by l 2 ( 𝒜 . 1-degree maps are also applied to some problems of Markov chains.

  8. Aeroelastic stability analysis of high aspect ratio aircraft wings

    OpenAIRE

    Banerjee, J. R.; Liu, X.; Kassem, H. I.

    2014-01-01

    Free vibration and flutter analyses of two types of high aspect ratio aircraft wings are presented. The wing is idealised as an assembly of bending-torsion coupled beams using the dynamic stiffness method leading to a nonlinear eigenvalue problem. This problem is solved using the Wattrick-Williams algorithm yielding natural frequencies and mode shapes. The flutter analysis is carried out using the normal mode method in conjunction with generalised coordinates and two-dimensional unsteady aero...

  9. Simulating Bird Strike on Aircraft Composite Wing Leading Edge.

    OpenAIRE

    Ericsson, Max

    2012-01-01

    In this master thesis project the possibility to model the response of a wing when subjected to bird strike using finite elements is analyzed. Since this transient event lasts only a few milliseconds the used solution method is explicit time integration. The wing is manufactured using carbon fiber laminate. Carbon fiber laminates have orthotropic material properties with different stiffness in different directions. Accordingly, there are damage mechanisms not considered when using metal that ...

  10. A Drone with Insect-Inspired Folding Wings

    OpenAIRE

    Dufour, Louis; Owen, Kevin; Mintchev, Stefano; Floreano, Dario

    2016-01-01

    Flying robots are increasingly adopted in search and rescue missions because of their capability to quickly collect and stream information from remote and dangerous areas. To further enhance their use, we are investigating the development of a new class of drones, foldable sensorized hubs that can quickly take off from rescuers’ hands as soon as they are taken out of a pocket or a backpack. With this aim, this paper presents the development of a foldable wing inspired by insects. The wing can...

  11. A Computational Method for Wings of Arbitrary Planform.

    Science.gov (United States)

    1984-12-01

    wing is considered variable with discrete values at the specified grid points. h3. nir -= difference equations are utilizedl to determine these discrete...separate circulation functions, one non-dimenstonai with respect to semi-span and fr-ee =, Cream velocity, and one non-dimensional with respect to mean...mapping points on the wing from the physical (xy)-plane to corresponding points in the ’o )-plane and - ice versa. Fig. 4 depicts a uni-orm rectangular

  12. Unveiling spatial correlations in biophotonic architecture of transparent insect wings

    CERN Document Server

    Kumar, Pramod; Singh, Dhirendra P; Mandal, Sudip; Singh, Kamal P

    2014-01-01

    We probe the natural complex structures in the transparent insect wings by a simple, non-invasive, real time optical technique using both monochromatic and broadband femtosecond lasers. A stable, reproducible and novel diffraction pattern is observed unveiling long range spatial correlations and structural-symmetry at various length scales for a large variety of wings. While matching the sensitivity of SEM for such microstructures, it is highly efficient for extracting long range structural organization with potentially broad applicability.

  13. Spatial Disorientation Training in the Rotor Wing Flight Simulator.

    Science.gov (United States)

    Powell-Dunford, Nicole; Bushby, Alaistair; Leland, Richard A

    This study is intended to identify efficacy, evolving applications, best practices, and challenges of spatial disorientation (SD) training in flight simulators for rotor wing pilots. Queries of a UK Ministry of Defense research database and Pub Med were undertaken using the search terms 'spatial disorientation,' 'rotor wing,' and 'flight simulator.' Efficacy, evolving applications, best practices, and challenges of SD simulation for rotor wing pilots were also ascertained through discussion with subject matter experts and industrial partners. Expert opinions were solicited at the aeromedical physiologist, aeromedical psychologist, instructor pilot, aeromedical examiner, and corporate executive levels. Peer review literature search yielded 129 articles, with 5 relevant to the use of flight simulators for the spatial disorientation training of rotor wing pilots. Efficacy of such training was measured subjectively and objectively. A preponderance of anecdotal reports endorse the benefits of rotor wing simulator SD training, with a small trial substantiating performance improvement. Advancing technologies enable novel training applications. The mobile nature of flight students and concurrent anticollision technologies can make long-range assessment of SD training efficacy challenging. Costs of advanced technologies could limit the extent to which the most advanced simulators can be employed across the rotor wing community. Evidence suggests the excellent training value of rotor wing simulators for SD training. Objective data from further research, particularly with regards to evolving technologies, may justify further usage of advanced simulator platforms for SD training and research. Powell-Dunford N, Bushby A, Leland RA. Spatial disorientation training in the rotor wing flight simulator. Aerosp Med Hum Perform. 2016; 87(10):890-893.

  14. Simulating Bird Strike on Aircraft Composite Wing Leading Edge.

    OpenAIRE

    Ericsson, Max

    2012-01-01

    In this master thesis project the possibility to model the response of a wing when subjected to bird strike using finite elements is analyzed. Since this transient event lasts only a few milliseconds the used solution method is explicit time integration. The wing is manufactured using carbon fiber laminate. Carbon fiber laminates have orthotropic material properties with different stiffness in different directions. Accordingly, there are damage mechanisms not considered when using metal that ...

  15. A Variable Control Structure Controller for the Wing Rock Phenomenon

    OpenAIRE

    2016-01-01

    This paper presents the design of a variable structure controller for the model of the wing rock phenomenon of a delta wing aircraft. It is considered to be a continue study of the last two researches for the same phenomena "Feedback linearization [15] and back stepping controller [14] ". A control technique is proposed to stabilize the aircraft phenomena. The solution presented in this paper give a guarantee of asymptotic convergence to zero of all variables of the system. MATLAB...

  16. CFD Analysis of a T-38 Wing Fence

    Science.gov (United States)

    2007-06-01

    or making major adjustments to the existing airframe. The answer lies in flow control. Flow control devices like vortex generators, winglets , and wing...proposed by the Air Force Test Pilot School. The driving force for considering a wing fence as opposed to vane vortex generators or winglets 3 was a row of...devices are vortex generators, fences, high lift flaps, and winglets . Active flow control injects the boundary layer with energy from small jets of

  17. Design of a variable-span morphing wing

    OpenAIRE

    Mestrinho, João Rafael da Conceição

    2009-01-01

    The present work focuses on the study, design and validation of a variable-span morphing wing to be tted to the UAV \\Olharapo". Using an optimization code, which uses a viscous two-dimensional panel method formulation coupled with a non-linear liftingline algorithm and a sequential quadratic programming optimization routine, na aerodynamic analysis is performed to estimate the optimal values of wing span which ensure minimum drag across the ight speed envelope. The UAV ies in a relativ...

  18. Do the Golden-winged Warbler and Blue-winged Warbler Exhibit Species-specific Differences in their Breeding Habitat Use?

    Directory of Open Access Journals (Sweden)

    David S. Maehr

    2010-12-01

    Full Text Available We compared habitat features of Golden-winged Warbler (Vermivora chrysoptera territories in the presence and absence of the Blue-winged Warbler (V. cyanoptera on reclaimed coal mines in southeastern Kentucky, USA. Our objective was to determine whether there are species specific differences in habitat that can be manipulated to encourage population persistence of the Golden-winged Warbler. When compared with Blue-winged Warblers, Golden-winged Warblers established territories at higher elevations and with greater percentages of grass and canopy cover. Mean territory size (minimum convex polygon was 1.3 ha (se = 0.1 for Golden-winged Warbler in absence of Blue-winged Warbler, 1.7 ha (se = 0.3 for Golden-winged Warbler coexisting with Blue-winged Warbler, and 2.1 ha (se = 0.3 for Blue-winged Warbler. Territory overlap occurred within and between species (18 of n = 73 territories, 24.7%. All Golden-winged and Blue-winged Warblers established territories that included an edge between reclaimed mine land and mature forest, as opposed to establishing territories in open grassland/shrubland habitat. The mean distance territories extended from a forest edge was 28.0 m (se = 3.8 for Golden-winged Warbler in absence of Blue-winged Warbler, 44.7 m (se = 5.7 for Golden-winged Warbler coexisting with Blue-winged Warbler, and 33.1 m (se = 6.1 for Blue-winged Warbler. Neither territory size nor distances to forest edges differed significantly between Golden-winged Warbler in presence or absence of Blue-winged Warbler. According to Monte Carlo analyses, orchardgrass (Dactylis glomerata, green ash (Fraxinus pennsylvanica seedlings and saplings, and black locust (Robinia pseudoacacia saplings were indicative of sites with only Golden-winged Warblers. Sericea lespedeza, goldenrod (Solidago spp., clematis vine (Clematis spp., and blackberry (Rubus spp. were indicative of sites where both species occurred. Our findings complement recent genetic studies and add

  19. Features of owl wings that promote silent flight.

    Science.gov (United States)

    Wagner, Hermann; Weger, Matthias; Klaas, Michael; Schröder, Wolfgang

    2017-02-06

    Owls are an order of birds of prey that are known for the development of a silent flight. We review here the morphological adaptations of owls leading to silent flight and discuss also aerodynamic properties of owl wings. We start with early observations (until 2005), and then turn to recent advances. The large wings of these birds, resulting in low wing loading and a low aspect ratio, contribute to noise reduction by allowing slow flight. The serrations on the leading edge of the wing and the velvet-like surface have an effect on noise reduction and also lead to an improvement of aerodynamic performance. The fringes at the inner feather vanes reduce noise by gliding into the grooves at the lower wing surface that are formed by barb shafts. The fringed trailing edge of the wing has been shown to reduce trailing edge noise. These adaptations to silent flight have been an inspiration for biologists and engineers for the development of devices with reduced noise production. Today several biomimetic applications such as a serrated pantograph or a fringed ventilator are available. Finally, we discuss unresolved questions and possible future directions.

  20. Flying Wings. A New Paradigm for Civil Aviation?

    Directory of Open Access Journals (Sweden)

    R. Martinez-Val

    2007-01-01

    Full Text Available Over the last 50 years, commercial aviation has been mainly based what is currently called the conventional layout, characterized by a slender fuselage mated to a high aspect ratio wing, with aft-tail planes and pod-mounted engines under the wing. However, it seems that this primary configuration is approaching an asymptote in its productivity and performance characteristics. One of the most promising configurations for the future is the flying wing in its distinct arrangements: blended-wing-body, C-wing, tail-less aircraft, etc. These layouts might provide significant fuel savings and, hence, a decrease in pollution. This configuration would also reduce noise in take-off and landing. All this explains the great deal of activity carried out by the aircraft industry and by numerous investigators to perform feasibility and conceptual design studies of this aircraft layout to gain better knowledge of its main characteristics: productivity, airport compatibility, passenger acceptance, internal architecture, emergency evacuation, etc. The present paper discusses the main features of flying wings, their advantages over conventional competitors, and some key operational issues, such as evacuation and vortex wake intensity. 

  1. Unsteady flow over flexible wings at different low Reynolds numbers

    Directory of Open Access Journals (Sweden)

    Genç Mustafa Serdar

    2016-01-01

    Full Text Available In this study, unsteady flow around flexible membrane wing which had aspect ratio of 1 (AR=1 was investigated experimentally at various Reynolds numbers (Re = 25000 and Re = 50000. Smoke-wire technique for flow visualization over the flexible membrane wing was utilized in the experiments. Digital Image Correlation system (DIC was used for measuring deformation of AR = 1 flexible membrane wing. Instantaneous deformation measurements of membrane wing were combined with the flow field measurements. In low aspect ratio flexible membrane wings, unsteadiness includes tip vortices and vortex shedding, and the combination of tip vortices. In these types of wings, complex unsteady deformations occurred due to vortex shedding. The results showed that the increasing angle of attack results in increase of membrane deformation. Moreover, it was concluded that analysis of the instantaneous deformation revealed chordwise and spanwise, modes which were due to the shedding of leading-edge vortices as well as tip vortices. Consequently, vibrational mode decreased and maximum standard deviation location approached to the trailing edge by reason of increasing angle of attack.

  2. Passive flow control by membrane wings for aerodynamic benefit

    Science.gov (United States)

    Timpe, Amory; Zhang, Zheng; Hubner, James; Ukeiley, Lawrence

    2013-03-01

    The coupling of passive structural response of flexible membranes with the flow over them can significantly alter the aerodynamic characteristic of simple flat-plate wings. The use of flexible wings is common throughout biological flying systems inspiring many engineers to incorporate them into small engineering flying systems. In many of these systems, the motion of the membrane serves to passively alter the flow over the wing potentially resulting in an aerodynamic benefit. In this study, the aerodynamic loads and the flow field for a rigid flat-plate wing are compared to free trailing-edge membrane wings with two different pre-tensions at a chord-based Reynolds number of approximately 50,000. The membrane was silicon rubber with a scalloped free trailing edge. The analysis presented includes load measurements from a sting balance along with velocity fields and membrane deflections from synchronized, time-resolved particle image velocimetry and digital image correlation. The load measurements demonstrate increased aerodynamic efficiency and lift, while the synchronized flow and membrane measurements show how the membrane motion serves to force the flow. This passive flow control introduced by the membranes motion alters the flows development over the wing and into the wake region demonstrating how, at least for lower angles of attack, the membranes motion drives the flow as opposed to the flow driving the membrane motion.

  3. A fast Chebyshev method for simulating flexible-wing propulsion

    Science.gov (United States)

    Moore, M. Nicholas J.

    2017-09-01

    We develop a highly efficient numerical method to simulate small-amplitude flapping propulsion by a flexible wing in a nearly inviscid fluid. We allow the wing's elastic modulus and mass density to vary arbitrarily, with an eye towards optimizing these distributions for propulsive performance. The method to determine the wing kinematics is based on Chebyshev collocation of the 1D beam equation as coupled to the surrounding 2D fluid flow. Through small-amplitude analysis of the Euler equations (with trailing-edge vortex shedding), the complete hydrodynamics can be represented by a nonlocal operator that acts on the 1D wing kinematics. A class of semi-analytical solutions permits fast evaluation of this operator with O (Nlog ⁡ N) operations, where N is the number of collocation points on the wing. This is in contrast to the minimum O (N2) cost of a direct 2D fluid solver. The coupled wing-fluid problem is thus recast as a PDE with nonlocal operator, which we solve using a preconditioned iterative method. These techniques yield a solver of near-optimal complexity, O (Nlog ⁡ N) , allowing one to rapidly search the infinite-dimensional parameter space of all possible material distributions and even perform optimization over this space.

  4. Phase shifts of the paired wings of butterfly diagrams

    Institute of Scientific and Technical Information of China (English)

    Ke-Jun Li; Hong-Fei Liang; Wen Feng

    2010-01-01

    Sunspot groups observed by the Royal Greenwich Observatory/US Air Force/NOAA from 1874 May to 2008 November and the Carte Synoptique solar filaments from 1919 March to 1989 December are used to investigate the relative phase shift of the paired wings of butterfly diagrams of sunspot and filament activities.Latitudinal migration of sunspot groups(or filaments)does asynchronously occur in the northern and southern hemispheres,and there is a relative phase shift between the paired wings of their butterfly diagrams in a cycle,making the paired wings spatially asymmetrical on the solar equator.It is inferred that hemispherical solar activity strength should evolve in a similar way within the paired wings of a butterfly diagram in a cycle,demonstrating the paired wings phenomenon and showing the phase relationship between the northern and southern hemispherical solar activity strengths,as well as a relative phase shift between the paired wings of a butterfly diagram,which should bring about almost the same relative phase shift of hemispheric solar activity strength.

  5. The Phase Shifts of the Paired Wings of Butterfly Diagrams

    CERN Document Server

    Li, Kejun; Feng, Wen

    2010-01-01

    Sunspot groups observed by Royal Greenwich Observatory/US Air Force/NOAA from May 1874 to November 2008 and the Carte Synoptique solar filaments from March 1919 to December 1989 are used to investigate the relative phase shift of the paired wings of butterfly diagrams of sunspot and filament activities. Latitudinal migration of sunspot groups (or filaments) does asynchronously occur in the northern and southern hemispheres, and there is a relative phase shift between the paired wings of their butterfly diagrams in a cycle, making the paired wings spatially asymmetrical on the solar equator. It is inferred that hemispherical solar activity strength should evolve in a similar way within the paired wings of a butterfly diagram in a cycle, making the paired wings just and only keep the phase relationship between the northern and southern hemispherical solar activity strengths, but a relative phase shift between the paired wings of a butterfly diagram should bring about an almost same relative phase shift of hemis...

  6. Unsteady flow over flexible wings at different low Reynolds numbers

    Science.gov (United States)

    Genç, Mustafa Serdar; Özden, Mustafa; Hakan Açikel, Halil; Demir, Hacımurat; Isabekov, Iliasbek

    2016-03-01

    In this study, unsteady flow around flexible membrane wing which had aspect ratio of 1 (AR=1) was investigated experimentally at various Reynolds numbers (Re = 25000 and Re = 50000). Smoke-wire technique for flow visualization over the flexible membrane wing was utilized in the experiments. Digital Image Correlation system (DIC) was used for measuring deformation of AR = 1 flexible membrane wing. Instantaneous deformation measurements of membrane wing were combined with the flow field measurements. In low aspect ratio flexible membrane wings, unsteadiness includes tip vortices and vortex shedding, and the combination of tip vortices. In these types of wings, complex unsteady deformations occurred due to vortex shedding. The results showed that the increasing angle of attack results in increase of membrane deformation. Moreover, it was concluded that analysis of the instantaneous deformation revealed chordwise and spanwise, modes which were due to the shedding of leading-edge vortices as well as tip vortices. Consequently, vibrational mode decreased and maximum standard deviation location approached to the trailing edge by reason of increasing angle of attack.

  7. Application of Piezoelectrics to Flapping-Wing MAVs

    Science.gov (United States)

    Widstrand, Alex; Hubner, J. Paul

    2015-11-01

    Micro air vehicles (MAVs) are a class of unmanned aerial vehicles that are size-restricted and operate at low velocities and low Reynolds numbers. An ongoing challenge with MAVs is that their flight-related operations are highly constrained by their size and weight, which limits battery size and, therefore, available power. One type of MAV called an ornithopter flies using flapping wings to create both lift and thrust, much like birds and insects do. Further bio-inspiration from bats led to the design of membrane wings for these vehicles, which provide aerodynamic benefits through passive vibration. In an attempt to capitalize on this vibration, a piezoelectric film, which generates a voltage when stressed, was investigated as the wing surface. Two wing planforms with constant area were designed and fabricated. The goal was to measure the wings' flight characteristics and output energy in freestream conditions. Complications with the flapper arose which prevented wind tunnel tests from being performed; however, energy data was obtained from table-top shaker tests. Preliminary results indicate that wing shape affects the magnitude of the charge generated, with a quarter-elliptic planform outperforming a rectangular planform. Funding provided by NSF REU Site Award number 1358991.

  8. Genetic Basis of Melanin Pigmentation in Butterfly Wings.

    Science.gov (United States)

    Zhang, Linlin; Martin, Arnaud; Perry, Michael W; van der Burg, Karin R L; Matsuoka, Yuji; Monteiro, Antónia; Reed, Robert D

    2017-04-01

    Despite the variety, prominence, and adaptive significance of butterfly wing patterns, surprisingly little is known about the genetic basis of wing color diversity. Even though there is intense interest in wing pattern evolution and development, the technical challenge of genetically manipulating butterflies has slowed efforts to functionally characterize color pattern development genes. To identify candidate wing pigmentation genes, we used RNA sequencing to characterize transcription across multiple stages of butterfly wing development, and between different color pattern elements, in the painted lady butterfly Vanessa cardui This allowed us to pinpoint genes specifically associated with red and black pigment patterns. To test the functions of a subset of genes associated with presumptive melanin pigmentation, we used clustered regularly interspaced short palindromic repeats (CRISPR)/Cas9 genome editing in four different butterfly genera. pale, Ddc, and yellow knockouts displayed reduction of melanin pigmentation, consistent with previous findings in other insects. Interestingly, however, yellow-d, ebony, and black knockouts revealed that these genes have localized effects on tuning the color of red, brown, and ochre pattern elements. These results point to previously undescribed mechanisms for modulating the color of specific wing pattern elements in butterflies, and provide an expanded portrait of the insect melanin pathway. Copyright © 2017 by the Genetics Society of America.

  9. A low-cost simulation platform for flapping wing MAVs

    Science.gov (United States)

    Kok, J. M.; Chahl, J. S.

    2015-03-01

    This paper describes the design of a flight simulator for analysing the systems level performance of a Dragonfly-Inspired Micro Air Vehicle (DIMAV). A quasi-steady blade element model is used to analyse the aerodynamic forces. Aerodynamic and environmental forces are then incorporated into a real world flight dynamics model to determine the dynamics of the DIMAV system. The paper also discusses the implementation of the flight simulator for analysing the manoeuvrability of a DIMAV, specifically several modes of flight commonly found in dragonflies. This includes take-off, roll turns and yaw turns. Our findings with the simulator are consistent with results from wind tunnel studies and slow motion cinematography of dragonflies. In the take-off mode of flight, we see a strong dependence of take-off accelerations with flapping frequency. An increase in wing-beat frequency of 10% causes the maximum vertical acceleration to increase by 2g which is similar to that of dragonflies in nature. For the roll and yaw modes of manoeuvring, asymmetrical inputs are applied between the left and right set of wings. The flapping amplitude is increased on the left pair of wings which causes a time averaged roll rate to the right of 1.76rad/s within two wing beats. In the yaw mode, the stroke plane angle is reduced in the left pair of wings to initiate the yaw manoeuvre. In two wing beats, the time averaged yaw rate is 2.54rad/s.

  10. HadISST (1-degree)/HadISST (1-degree)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Monthly version of HadISST sea surface temperature component (1-degree). See Rayner, N. A., Parker, D. E., Horton, E. B., Folland, C. K., Alexander, L. V., Rowell,...

  11. Reassessment of the wing feathers of Archaeopteryx lithographica suggests no robust evidence for the presence of elongated dorsal wing coverts.

    Directory of Open Access Journals (Sweden)

    Robert L Nudds

    Full Text Available Recently it was proposed that the primary feathers of Archaeopteryx lithographica (HMN1880 were overlaid by long covert feathers, and that a multilayered feathered wing was a feature of early fossils with feathered forelimbs. The proposed long covert feathers of Archaeopteryx were previously interpreted as dorsally displaced remiges or a second set of impressions made by the wing. The following study shows that the qualitative arguments forwarded in support of the elongated covert hypothesis are neither robust nor supported quantitatively. The idea that the extant bird wing with its single layer of overlapping primaries evolved from an earlier multilayered heavily coveted feathered forelimb as seen in Anchiornis huxleyi is reasonable. At this juncture, however, it is premature to conclude unequivocally that the wing of Archaeopteryx consisted of primary feathers overlaid with elongated coverts.

  12. Aerodynamic characteristics of a high-wing transport configuration with a over-the-wing nacelle-pylon arrangement

    Science.gov (United States)

    Henderson, W. P.; Abeyounis, W. K.

    1985-01-01

    An investigation has been conducted in the Langley 16-Foot Transonic Tunnel to determine the effects on the aerodynamic characteristics of a high-wing transport configuration of installing an over-the-wing nacelle-pylon arrangement. The tests are conducted at Mach numbers from 0.70 to 0.82 and at angles of attack from -2 deg to 4 deg. The configurational variables under study include symmetrical and contoured nacelles and pylons, pylon size, and wing leading-edge extensions. The symmetrical nacelles and pylons reduce the lift coefficient, increase the drag coefficient, and cause a nose-up pitching-moment coefficient. The contoured nacelles significantly reduce the interference drag, though it is still excessive. Increasing the pylon size reduces the drag, whereas adding wing leading-edge extension does not affect the aerodynamic characteristics significantly.

  13. Fuzzy Model-based Pitch Stabilization and Wing Vibration Suppression of Flexible Wing Aircraft.

    Science.gov (United States)

    Ayoubi, Mohammad A.; Swei, Sean Shan-Min; Nguyen, Nhan T.

    2014-01-01

    This paper presents a fuzzy nonlinear controller to regulate the longitudinal dynamics of an aircraft and suppress the bending and torsional vibrations of its flexible wings. The fuzzy controller utilizes full-state feedback with input constraint. First, the Takagi-Sugeno fuzzy linear model is developed which approximates the coupled aeroelastic aircraft model. Then, based on the fuzzy linear model, a fuzzy controller is developed to utilize a full-state feedback and stabilize the system while it satisfies the control input constraint. Linear matrix inequality (LMI) techniques are employed to solve the fuzzy control problem. Finally, the performance of the proposed controller is demonstrated on the NASA Generic Transport Model (GTM).

  14. The Effect of Height, Wing Length, and Wing Symmetry on Tabebuia rosea Seed Dispersal

    Directory of Open Access Journals (Sweden)

    Yasmeen Moussa

    2014-12-01

    Full Text Available The relationship between the vertical drop height and the horizontal distance traveled (dispersal ratio was investigated for a sample of fifty Tabebuia rosea seeds by dropping the seeds from five heights ranging from 1.00 to 2.00 meters. The dispersal ratio was found to be a constant 0.16 m/m for these heights. The effects of total seed length and asymmetry of seed wings on dispersal ratio were also measured using separate samples of fifty Tabebuia rosea seeds. It was found that neither seed length nor asymmetry had a significant effect on the dispersal ratio.

  15. Observations and Measurements of Wing Parameters of the Selected Beetle Species and the Design of a Mechanism Structure Implementing a Complex Wing Movement

    Directory of Open Access Journals (Sweden)

    Geisler T.

    2016-12-01

    Full Text Available Beetle wings perform a flapping movement, consisting of the rotation relative to the two axes. This paper presents the results of observations and measurements of wings operating parameters in different planes of some beetle species. High speed photos and videos were used. The concept of the mechanism performing a complex wing movement was proposed and developed.

  16. Degree-degree correlations in directed networks with heavy-tailed degrees

    NARCIS (Netherlands)

    Hoorn, van der Pim; Litvak, Nelly

    2013-01-01

    In network theory, Pearson's correlation coefficients are most commonly used to measure the degree assortativity of a network. We investigate the behavior of these coefficients in the setting of directed networks with heavy-tailed degree sequences. We prove that for graphs where the in- and out-degr

  17. Degree-degree dependencies in directed networks with heavy-tailed degrees

    NARCIS (Netherlands)

    Hoorn, van der Pim; Litvak, Nelly

    2015-01-01

    In network theory, Pearson’s correlation coefficients are most commonly used to measure the degree assortativity of a network. We investigate the behavior of these coefficients in the setting of directed networks with heavy-tailed degree sequences. We prove that for graphs where the in- and out-degr

  18. Killing Horizons Kill Horizon Degrees

    Science.gov (United States)

    Bergamin, L.; Grumiller, D.

    Frequently, it is argued that the microstates responsible for the Bekenstein-Hawking entropy should arise from some physical degrees of freedom located near or on the black hole horizon. In this essay, we elucidate that instead entropy may emerge from the conversion of physical degrees of freedom, attached to a generic boundary, into unobservable gauge degrees of freedom attached to the horizon. By constructing the reduced phase space, it can be demonstrated that such a transmutation indeed takes place for a large class of black holes, including Schwarzschild.

  19. Killing horizons kill horizon degrees

    CERN Document Server

    Bergamin, L

    2006-01-01

    Frequently it is argued that the microstates responsible for the Bekenstein-Hawking entropy should arise from some physical degrees of freedom located near or on the black hole horizon. In this Essay we elucidate that instead entropy may emerge from the conversion of physical degrees of freedom, attached to a generic boundary, into unobservable gauge degrees of freedom attached to the horizon. By constructing the reduced phase space it can be demonstrated that such a transmutation indeed takes place for a large class of black holes, including Schwarzschild.

  20. Pigs taking wing with transposons and recombinases

    Science.gov (United States)

    Clark, Karl J; Carlson, Daniel F; Fahrenkrug, Scott C

    2007-01-01

    Swine production has been an important part of our lives since the late Mesolithic or early Neolithic periods, and ranks number one in world meat production. Pig production also contributes to high-value-added medical markets in the form of pharmaceuticals, heart valves, and surgical materials. Genetic engineering, including the addition of exogenous genetic material or manipulation of the endogenous genome, holds great promise for changing pig phenotypes for agricultural and medical applications. Although the first transgenic pigs were described in 1985, poor survival of manipulated embryos; inefficiencies in the integration, transmission, and expression of transgenes; and expensive husbandry costs have impeded the widespread application of pig genetic engineering. Sequencing of the pig genome and advances in reproductive technologies have rejuvenated efforts to apply transgenesis to swine. Pigs provide a compelling new resource for the directed production of pharmaceutical proteins and the provision of cells, vascular grafts, and organs for xenotransplantation. Additionally, given remarkable similarities in the physiology and size of people and pigs, swine will increasingly provide large animal models of human disease where rodent models are insufficient. We review the challenges facing pig transgenesis and discuss the utility of transposases and recombinases for enhancing the success and sophistication of pig genetic engineering. 'The paradise of my fancy is one where pigs have wings.' (GK Chesterton). PMID:18047690

  1. A new technique for investigating the induced and profile drag coefficients of a smooth wing and a tubercled wing

    Directory of Open Access Journals (Sweden)

    Bolzon Michael

    2016-01-01

    Full Text Available The induced and profile drag coefficients of a wing are typically determined through a complex experimental technique, such as wake surveying. Such a technique requires measurement of all three orthogonal components of the downstream velocity to find the components of drag, which results in the necessary usage of a sophisticated and costly measurement device, such as multi-hole pressure probe. However, in this paper data is presented which demonstrate that the relative changes in the induced and profile drag coefficients can largely be determined through the sole measurement of the downstream, streamwise velocity. To demonstrate this, the induced and profile drags of two NACA 0021 wings, one with a smooth leading edge and the other wing a tubercled leading edge for comparison, are determined through the measurement of the three orthogonal velocities. The downstream, streamwise velocity distribution of each wing is then constructed and relationships can be determined. The wings were surveyed at 3°, 9°, and 12°. It has been found that the relative magnitude of the profile drag coefficient can be found for all considered angles of attack, while the relative magnitude of the induced drag coefficient can be found at 9° and 12°. These findings produce an innovative, simpler, and more cost effective experimental technique in determining the components of drag of a wing, and reduces the burdensome requirement of a sophisticated measurement device for such an experiment. Further investigation is required to determine the induced drag at 3°.

  2. Performance of the bio-inspired leading edge protuberances on a static wing and a pitching wing

    Institute of Scientific and Technical Information of China (English)

    胡文蓉; 张仕栋; 王雅赟

    2014-01-01

    It is shown that the leading edge protuberances on the flippers of a humpback whale can significantly improve the hydrodynamic performance. The present study numerically investigates the flow control mechanisms of the leading edge protuberances on a static wing and a pitching wing. For static wings, the performance in both laminar flow and turbulent flow are studied in the context of the flow control mechanisms. It is shown that the protuberances have slight effects on the performance of static wings in laminar flow. Also, it could be deduced that non-uniform downwash does not delay the stall occurrence in either laminar flow or turbulent flow. In turbulent flow, the leading edge protuberances act in a manner similar to vortex generators, enhancing the momentum exchange within the boundary layer. Streamwise vortices do contribute to the delay of the stall occurrence. The normal vorticity component also plays an important role in delaying the stall occurrence. However, for the pitching wing, the effect of leading edge protuberances is negligible in turbulent flow. Detailed analysis of the flow field indicates that for the wing with the leading edge protuberances, the leading edge vortices become more complex, while the thrust jet and the vortices in the wake are not changed significantly by the leading edge protuberances.

  3. Pulsed eddy current inspection of CF-188 inner wing spar

    Science.gov (United States)

    Horan, Peter Francis

    Royal Canadian Air Force (RCAF) CF-188 Hornet aircraft engineering authorities have stated a requirement for a Non-Destructive Evaluation (NDE) technique to detect Stress Corrosion Cracking (SCC) in the inner wing spars without fastener or composite wing skin removal. Current radiographic inspections involve significant aircraft downtime, and Pulsed Eddy Current (PEC) inspection is proposed as a solution. The aluminum inner wing spars of CF-188 Hornet aircraft may undergo stress corrosion cracking (SCC) along the spar between the fasteners that secure carbon-fiber/ epoxy composite skin to the wing. Inspection of the spar through the wing skin is required to avoid wing disassembly. The thickness of the wing skin varies between 8 and 20 mm (0.3 to 0.8 inch) and fasteners may be either titanium or ferrous. PEC generated by a probe centered over a fastener, demonstrates capability of detecting simulated cracks within spars with the wing skin present. Comparison of signals from separate sensors, mounted to either side of the excitation coil, is used to detect differences in induced eddy current fields, which arise in the presence of cracks. To overcome variability in PEC signal response due to variation in 1) skin thickness, 2) fastener material and size, and 3) centering over fasteners, a large calibration data set is acquired. Multi-dimensional scores from a Modified Principal Components Analysis (PCA) of the data are reduced to one dimension (1D) using a Discriminant Analysis method. Under inspection conditions, calibrated PCA scores combined with discriminant analysis permit rapid real time go/no-go PEC detection of cracks in CF-188 inner wing spar. Probe designs using both pickup coils and Giant Magnetoresistive (GMR) sensors were tested on samples with the same ferrous and titanium fasteners found on the CF-188. Flaws were correctly detected at lift-offs of up to 21mm utilizing a variety of insulating skin materials simulating the carbon-fibre reinforced polymer

  4. Performance Assessment in a Heat Exchanger Tube with Opposite/Parallel Wing Twisted Tapes

    Directory of Open Access Journals (Sweden)

    S. Eiamsa-ard

    2015-02-01

    Full Text Available The thermohydraulic performance in a tube containing a modified twisted tape with alternate-axes and wing arrangements is reported. This work aims to investigate the effects of wing arrangements (opposite (O and parallel (P wings at different wing shapes (triangle (Tri, rectangular (Rec, and trapezoidal (Tra wings and on the thermohydraulic performance characteristics. The obtained results show that wing twisted tapes with all wing shape arrangements (O-Tri/O-Rec/O-Tra/P-Tri/P-Rec/P-Tra give superior thermohydraulic performance and heat transfer rate to the typical twisted tape. In addition, the tapes with opposite wing arrangement of O-Tra, O-Rec, and O-Tri give superior thermohydraulic performances to those with parallel wing arrangement of P-Tra, P-Rec, and P-Tri around 2.7%, 3.5%, and 3.2%, respectively.

  5. The moment of inertia of bird wings and the inertial power requirement for flapping flight

    Science.gov (United States)

    Berg; Rayner

    1995-01-01

    The agility and manoeuvrability of a flying animal and the inertial power required to flap the wings are related to the moment of inertia of the wings. The moments of inertia of the wings of 29 bird species and three bat species were determined using wing strip analysis. We also measured wing length, wing span, wing area, wing mass and body mass. A strong correlation (r2=0.997) was found between the moment of inertia and the product of wing mass and the square of wing length. Using this relationship, it was found that all birds that use their wings for underwater flight had a higher than average moment of inertia. Assuming sinusoidal wing movement, the inertial power requirement was found to be proportional to (body mass)0.799, an exponent close to literature values for both metabolic power output and minimum power required for flight. Ignoring wing retraction, a fairly approximate estimate showed that the inertial power required is 11­15 % of the minimum flight power. If the kinetic energy of the wings is partly converted into aerodynamic (useful) work at stroke reversal, the power loss due to inertial effects may be smaller.

  6. Spontaneous long-range calcium waves in developing butterfly wings.

    Science.gov (United States)

    Ohno, Yoshikazu; Otaki, Joji M

    2015-03-25

    Butterfly wing color patterns emerge as the result of a regular arrangement of scales produced by epithelial scale cells at the pupal stage. These color patterns and scale arrangements are coordinated throughout the wing. However, the mechanism by which the development of scale cells is controlled across the entire wing remains elusive. In the present study, we used pupal wings of the blue pansy butterfly, Junonia orithya, which has distinct eyespots, to examine the possible involvement of Ca(2+) waves in wing development. Here, we demonstrate that the developing pupal wing tissue of the blue pansy butterfly displayed spontaneous low-frequency Ca(2+) waves in vivo that propagated slowly over long distances. Some waves appeared to be released from the immediate peripheries of the prospective eyespot and discal spot, though it was often difficult to identify the specific origins of these waves. Physical damage, which is known to induce ectopic eyespots, led to the radiation of Ca(2+) waves from the immediate periphery of the damaged site. Thapsigargin, which is a specific inhibitor of Ca(2+)-ATPases in the endoplasmic reticulum, induced an acute increase in cytoplasmic Ca(2+) levels and halted the spontaneous Ca(2+) waves. Additionally, thapsigargin-treated wings showed incomplete scale development as well as other scale and color pattern abnormalities. We identified a novel form of Ca(2+) waves, spontaneous low-frequency slow waves, which travel over exceptionally long distances. Our results suggest that spontaneous Ca(2+) waves play a critical role in the coordinated development of scale arrangements and possibly in color pattern formation in butterflies.

  7. Drosophila Smad2 Opposes Mad Signaling during Wing Vein Development

    Science.gov (United States)

    Sander, Veronika; Eivers, Edward; Choi, Renee H.; De Robertis, Edward M.

    2010-01-01

    In the vertebrates, the BMP/Smad1 and TGF-β/Smad2 signaling pathways execute antagonistic functions in different contexts of development. The differentiation of specific structures results from the balance between these two pathways. For example, the gastrula organizer/node of the vertebrates requires a region of low Smad1 and high Smad2 signaling. In Drosophila, Mad regulates tissue determination and growth in the wing, but the function of dSmad2 in wing patterning is largely unknown. In this study, we used an RNAi loss-of-function approach to investigate dSmad2 signaling during wing development. RNAi-mediated knockdown of dSmad2 caused formation of extra vein tissue, with phenotypes similar to those seen in Dpp/Mad gain-of-function. Clonal analyses revealed that the normal function of dSmad2 is to inhibit the response of wing intervein cells to the extracellular Dpp morphogen gradient that specifies vein formation, as measured by expression of the activated phospho-Mad protein. The effect of dSmad2 depletion in promoting vein differentiation was dependent on Medea, the co-factor shared by Mad and dSmad2. Furthermore, double RNAi experiments showed that Mad is epistatic to dSmad2. In other words, depletion of Smad2 had no effect in Mad-deficient wings. Our results demonstrate a novel role for dSmad2 in opposing Mad-mediated vein formation in the wing. We propose that the main function of dActivin/dSmad2 in Drosophila wing development is to antagonize Dpp/Mad signaling. Possible molecular mechanisms for the opposition between dSmad2 and Mad signaling are discussed. PMID:20442782

  8. On degree-degree correlations in multilayer networks

    CERN Document Server

    de Arruda, Guilherme Ferraz; Moreno, Yamir; Rodrigues, Francisco A

    2015-01-01

    We propose a generalization of the concept of assortativity based on the tensorial representation of multilayer networks, covering the definitions given in terms of Pearson and Spearman coefficients. Our approach can also be applied to weighted networks and provides information about correlations considering pairs of layers. By analyzing the multilayer representation of the airport transportation network, we show that contrasting results are obtained when the layers are analyzed independently or as an interconnected system. Finally, we study the impact of the level of assortativity and heterogeneity between layers on the spreading of diseases. Our results highlight the need of studying degree-degree correlations on multilayer systems, instead of on aggregated networks.

  9. On degree-degree correlations in multilayer networks

    Science.gov (United States)

    de Arruda, Guilherme Ferraz; Cozzo, Emanuele; Moreno, Yamir; Rodrigues, Francisco A.

    2016-06-01

    We propose a generalization of the concept of assortativity based on the tensorial representation of multilayer networks, covering the definitions given in terms of Pearson and Spearman coefficients. Our approach can also be applied to weighted networks and provides information about correlations considering pairs of layers. By analyzing the multilayer representation of the airport transportation network, we show that contrasting results are obtained when the layers are analyzed independently or as an interconnected system. Finally, we study the impact of the level of assortativity and heterogeneity between layers on the spreading of diseases. Our results highlight the need of studying degree-degree correlations on multilayer systems, instead of on aggregated networks.

  10. Simplified physical models of the flow around flexible insect wings at low Reynolds numbers

    Science.gov (United States)

    Harenberg, Steve; Reis, Johnny; Miller, Laura

    2011-11-01

    Some of the smallest insects fly at Reynolds numbers in the range of 5-100. We built a dynamically scaled physical model of a flexible insect wing and measured the resulting wing deformations and flow fields. The wing models were submerged in diluted corn syrup and rotated about the root of the wing for Reynolds numbers ranging from 1-100. Spatially resolved flow fields were obtained using particle image velocimetry (PIV). Deformations of the wing were tracked using DLTdv software to determine the motion and induced curvature of the wing.

  11. Analysis of Kinematics of Flapping Wing UAV Using OptiTrack Systems

    OpenAIRE

    2016-01-01

    An analysis of the kinematics of a flapping membrane wing using experimental kinematic data is presented. This motion capture technique tracks the positon of the retroreflective marker(s) placed on the left wing of a 1.3-m-wingspan ornithopter. The time-varying three-dimensional data of the wing kinematics were recorded for a single frequency. The wing shape data was then plotted on a two-dimensional plane to understand the wing dynamic behaviour of an ornithopter. Specifically, the wing tip ...

  12. Reconfigurable Flight Control Design for Combat Flying Wing with Multiple Control Surfaces

    Institute of Scientific and Technical Information of China (English)

    WANG Lei; WANG Lixin

    2012-01-01

    With control using redundant multiple control surface arrangement and large-deflection drag rudders,a combat flying wing has a higher probability for control surface failures.Therefore,its flight control system must be able to reconfigure after such failures.Considering three types of typical control surface failures (lock-in-place (LIP),loss-of-effectiveness (LOE) and float),flight control reconfiguration characteristic and capability of such aircraft types are analyzed.Because of the control surface redundancy,the aircraft using the dynamic inversion flight control law already has a control allocation block.In this paper,its flight control configuration during the above failures is achieved by modifying this block.It is shown that such a reconfigurable flight control design is valid,through numerical simulations of flight attitude control task.Results indicate that,in the circumstances of control surface failures with limited degree and the degradation of the flying quality level,a combat flying wing adopting this flight control reconfiguration approach based on control allocation could guarantee its flight safety and perform some flight combat missions.

  13. Aeroelasticity Benchmark Assessment: Subsonic Fixed Wing Program

    Science.gov (United States)

    Florance, Jennifer P.; Chwalowski, Pawel; Wieseman, Carol D.

    2010-01-01

    Aeroelasticity Branch will examine other experimental efforts within the Subsonic Fixed Wing (SFW) program (such as testing of the NASA Common Research Model (CRM)) and other NASA programs and assess aeroelasticity issues and research topics.

  14. Age-class separation of blue-winged ducks

    Science.gov (United States)

    Hohman, W.L.; Moore, J.L.; Twedt, D.J.; Mensik, John G.; Logerwell, E.

    1995-01-01

    Accurate determination of age is of fundamental importance to population and life history studies of waterfowl and their management. Therefore, we developed quantitative methods that separate adult and immature blue-winged teal (Anas discors), cinnamon teal (A. cyanoptera), and northern shovelers (A. clypeata) during spring and summer. To assess suitability of discriminant models using 9 remigial measurements, we compared model performance (% agreement between predicted age and age assigned to birds on the basis of definitive cloacal or rectral feather characteristics) in different flyways (Mississippi and Pacific) and between years (1990-91 and 1991-92). We also applied age-classification models to wings obtained from U.S. Fish and Wildlife Service harvest surveys in the Mississippi and Central-Pacific flyways (wing-bees) for which age had been determined using qualitative characteristics (i.e., remigial markings, shape, or wear). Except for male northern shovelers, models correctly aged lt 90% (range 70-86%) of blue-winged ducks. Model performance varied among species and differed between sexes and years. Proportions of individuals that were correctly aged were greater for males (range 63-86%) than females (range 39-69%). Models for northern shovelers performed better in flyway comparisons within year (1991-92, La. model applied to Calif. birds, and Calif. model applied to La. birds: 90 and 94% for M, and 89 and 76% for F, respectively) than in annual comparisons within the Mississippi Flyway (1991-92 model applied to 1990-91 data: 79% for M, 50% for F). Exclusion of measurements that varied by flyway or year did not improve model performance. Quantitative methods appear to be of limited value for age separation of female blue-winged ducks. Close agreement between predicted age and age assigned to wings from the wing-bees suggests that qualitative and quantitative methods may be equally accurate for age separation of male blue-winged ducks. We interpret annual

  15. Postnatal development in Andersen's leaf-nosed bat Hipposideros pomona: flight, wing shape, and wing bone lengths.

    Science.gov (United States)

    Lin, Ai-Qing; Jin, Long-Ru; Shi, Li-Min; Sun, Ke-Ping; Berquist, Sean W; Liu, Ying; Feng, Jiang

    2011-04-01

    Postnatal changes in flight development, wing shape and wing bone lengths of 56 marked neonate Hipposideros pomona were investigated under natural conditions in southwest China. Flight experiments showed that pups began to flutter with a short horizontal displacement at 10 days and first took flight at 19 days, with most achieving sustained flight at 1 month old. Analysis of covariance on wingspan, wing area, and the other seven wing characteristics between 'pre-flight' and 'post-volancy' periods supports the hypothesis that growth had one 'pre-flight' trajectory and a different 'post-volancy' trajectory in bats. Wingspan, handwing length and area, armwing length and area, and total wing area increased linearly until the age of first flight, after which the growth rates decreased (all P Wing loading declined linearly until day 19 before ultimately decreasing to adult levels (P span-wise length and chord-wise length was evaluated to test the hypothesis that compensatory growth of wing bones in H. pomona occurred in both 'pre-flight' and 'post-volancy' periods. The frequency of short-long and long-short pairs was significantly greater than that of short-short, long-long pairs in most pairs of bone elements in adults. The results indicate that a bone 'shorter than expected' would be compensated by a bone or bones 'longer than expected', suggesting compensatory growth in H. pomona. The pairwise comparisons conducted in adults were also performed in young bats during 'pre-flight' and 'post-volancy' periods, demonstrating that compensatory growth occurred throughout postnatal ontogeny.

  16. Effect of insect density and host plant quality on wing-form in Megamelus scutellaris (Hemiptera: Delphacidae)

    Science.gov (United States)

    Megamelus scutellaris Berg (Hemiptera: Delphacidae) is a South American species that feeds on waterhyacinth, Eichhornia crassipes Mart. (Solms). This species exhibits significant wing dimorphism whereby fully winged adults (macropters) are capable of flight while those with reduced wings (brachtypt...

  17. a New Efficient Control Method for Blended Wing Body

    Science.gov (United States)

    Wu, Wenhua; Chen, Dehua; Qin, Ning; Peng, Xin; Tang, Xinwu

    The blended wing body (BWB) is the hottest one of the aerodynamic shapes of next generation airliner because of its' high lift-drag ratio, but there are still some flaws that cut down its aerodynamical performance. One of the most harmful flaws is the low efficiency of elevator and direction rudder, this makes the BWB hard to be controlled. In this paper, we proposed a new control method to solve this problem by morphing wing—that is, to control the BWB only by changing its wing shape but without any rudder. The pitching moments, rolling moments and yawing moments are plotted versus the parameters section and the wing shape in figures and are discussed in the paper. The result shows that the morphing wing can control the moments of BWB more precisely and in wider range. The pitching moments, rolling moments and yawing moments increases or decreases linearly or almost linearly, with the value of the selected parameters. These results show that using morphing wing is an excellent aerodynamic control way for a BWB craft.

  18. Stability of Alfvén wings in uniform plasmas

    Science.gov (United States)

    Sallago, P. A.; Platzeck, A. M.

    2007-12-01

    A conducting source moving uniformly through a magnetized plasma generates, among a variety of perturbations, Alfvén waves. An interesting characteristic of Alfvén waves is that they can build up structures in the plasma called Alfvén wings. These wings have been detected and measured in many solar system bodies, and their existence has also been theoretically proven. However, their stability remains to be studied. The aim of this paper is to analyze the stability of an Alfvén wing developed in a uniform background field, in the presence of an incompressible perturbation that has the same symmetry as the Alfvén wing, in the magnetohydrodynamic approximation. The study of the stability of a magnetohydrodynamic system is often performed by linearizing the equations and using either the normal modes method or the energy method. In spite of being applicable for many problems, both methods become algebraically complicated if the structure under analysis is a highly non-uniform one. Palumbo has developed an analytical method for the study of the stability of static structures with a symmetry in magnetized plasmas, in the presence of incompressible perturbations with the same symmetry as the structure (Palumbo 1998 Thesis, Universidad de Firenze, Italia). In the present paper we extend this method for Alfvén wings that are stationary structures, and conclude that in the presence of this kind of perturbation they are stable.

  19. Wing Warping and Its Impact on Aerodynamic Efficiency

    Science.gov (United States)

    Loh, Ben; Jacob, Jamey

    2007-11-01

    Inflatable wings have been demonstrated in many applications such as UAVs, airships, and missile stabilization surfaces. A major concern presented by the use of an inflatable wing has been the lack of traditional roll control surfaces. This leaves the designer with several options in order to have control about the roll axis. Since inflatable wings have a semi-flexible structure, wing warping is the obvious solution to this problem. The current method is to attach servos and control linkages to external surface of the wing that results in variation of profile chamber and angle of attack from leading edge or trailing edge deflection. Designs using internal muscles will also be discussed. This creates a lift differential between the half-spans, resulting in a roll moment. The trailing edge on the other half-span can also be deflected in the opposite direction to increase the roll moment as well as to reduce roll-yaw coupling. Comparisons show that higher L/D ratios are possible than using traditional control surfaces. An additional benefit is the ability to perform symmetric warping to achieve optimum aerodynamic performance. Via warping alone, an arbitrary span can be warped such that it has the same aerodynamic characteristics as an elliptical planform. Comparisons between lifting line theory and test results will be presented.

  20. PS2 integrin requirements in Drosophila embryo and wing morphogenesis.

    Science.gov (United States)

    Brabant, M C; Brower, D L

    1993-05-01

    The Drosophila inflated (if) gene encodes the alpha PS2 subunit of the PS integrins. We describe the generation of new if mutations, their lethal embryonic phenotype, and experiments that examine the spatial and temporal requirements for integrins in adult wing morphogenesis. Embryos hemizygous for either new allele, ifA7 or ifB2, make reduced amounts of alpha PS2. In a variety of genetic tests, these alleles behave similarly to ifk27e, which makes no detectable alpha PS2, and all three alleles display the same embryonic phenotype. We therefore conclude that all of the lethal alleles retain little or no wild-type alpha PS2 function. As seen for strong mutations at the myospheroid (mys) locus, which encodes the beta PS integrin subunit, if mutants show extreme defects in somatic muscle attachments and in midgut morphogenesis. Unlike mys, however, there is no dorsal herniation of the if mutant embryos. With respect to wing morphogenesis, clonal analysis experiments demonstrate that if+ function is required only in cells of the ventral wing surface. We have rescued the wing blister phenotype of double mutants for the hypomorphic mysnj42 and if3 alleles using a heat shock-inducible mys+ transgene. By varying times of transgene induction, we find that integrin function is required from very early in metamorphosis until at least the last 24-48 hr of wing development.

  1. Helical vortices generated by flapping wings of bumblebees

    Science.gov (United States)

    Farge, Marie; Engels, Thomas; Kolomenskiy, Dmitry; Schneider, Kai; Lehmann, Fritz; Sesterhenn, Jörn

    2016-11-01

    We analyze high resolution numerical simulation data of a bumblebee with fixed body and prescribed wing motion, flying in a numerical wind tunnel, presented in. The inflow condition of the tunnel varies from unperturbed laminar to strongly turbulent. The flow generated by the flapping wings indicates the important role of the leading edge vortex (LEV), responsible for elevated lift production and which is not significantly altered by the inflow turbulence. The LEV has a conical structure due to the three-dimensional motion of the wings. This flow configuration produces strong vorticity on the sharp leading edge and the outwards velocity (from the root to the tip of the wing) in the spanwise direction. Flow visualizations show that the generated vortical structures are characterized by a strong helicity. We study the evolution of the mean helicity for each wing and analyze the impact of turbulent inflow. We thankfully acknowledge financial support from the French-German AIFIT project funded by DFG and ANR (Grant 15-CE40-0019). DK gratefully acknowledges financial support from the JSPS postdoctoral fellowship.

  2. Passive mechanism of pitch recoil in flapping insect wings.

    Science.gov (United States)

    Ishihara, D; Horie, T

    2016-12-20

    The high torsional flexibility of insect wings allows for elastic recoil after the rotation of the wing during stroke reversal. However, the underlying mechanism of this recoil remains unclear because of the dynamic process of transitioning from the wing rotation during stroke reversal to the maintenance of a high angle of attack during the middle of each half-stroke, when the inertial, elastic, and aerodynamic effects all have a significant impact. Therefore, the interaction between the flapping wing and the surrounding air was directly simulated by simultaneously solving the incompressible Navier-Stokes equations, the equation of motion for an elastic body, and the fluid-structure interface conditions using the three-dimensional finite element method. This direct numerical simulation controlling the aerodynamic effect revealed that the recoil is the residual of the free pitch vibration induced by the flapping acceleration during stroke reversal in the transient response very close to critical damping due to the dynamic pressure resistance of the surrounding air. This understanding will enable the control of the leading-edge vortex and lift generation, the reduction of the work performed by flapping wings, and the interpretation of the underlying necessity for the kinematic characteristics of the flapping motion.

  3. Microneurolysis and decompression of long thoracic nerve injury are effective in reversing scapular winging: Long-term results in 50 cases

    Directory of Open Access Journals (Sweden)

    Lyons Andrew B

    2007-03-01

    Full Text Available Abstract Background Long thoracic nerve injury leading to scapular winging is common, often caused by closed trauma through compression, stretching, traction, direct extrinsic force, penetrating injury, or neuritides such as Parsonage-Turner syndrome. We undertook the largest series of long thoracic nerve decompression and neurolysis yet reported to demonstrate the usefulness of long thoracic nerve decompression. Methods Winging was bilateral in 3 of the 47 patients (26 male, 21 female, yielding a total of 50 procedures. The mean age of the patients was 33.4 years, ranging from 24–57. Causation included heavy weight-lifting (31 patients, repetitive throwing (5 patients, deep massage (2 patients, repetitive overhead movement (1 patient, direct trauma (1 patient, motor bike accident (1 patient, and idiopathic causes (9 patients. Decompression and microneurolysis of the long thoracic nerve were performed in the supraclavicular space. Follow-up (average of 25.7 months consisted of physical examination and phone conversations. The degree of winging was measured by the operating surgeon (RKN. Patients also answered questions covering 11 quality-of-life facets spanning four domains of the World Health Organization Quality of Life questionnaire. Results Thoracic nerve decompression and neurolysis improved scapular winging in 49 (98% of the 50 cases, producing "good" or "excellent" results in 46 cases (92%. At least some improvement occurred in 98% of cases that were less than 10 years old. Pain reduction through surgery was good or excellent in 43 (86% cases. Shoulder instability affected 21 patients preoperatively and persisted in 5 of these patients after surgery, even in the 5 patients with persistent instability who experienced some relief from the winging itself. Conclusion Surgical decompression and neurolysis of the long thoracic nerve significantly improve scapular winging in appropriate patients, for whom these techniques should be considered

  4. Do hummingbirds use a different mechanism than insects to flip and twist their wings?

    Science.gov (United States)

    Song, Jialei; Luo, Haoxiang; Hedrick, Tyson

    2014-11-01

    Hovering hummingbirds flap their wings in an almost horizontal stroke plane and flip the wings to invert the angle of attack after stroke reversal, a strategy also utilized by many hovering insects such as fruit flies. However, unlike insects whose wing actuation mechanism is only located at the base, hummingbirds have a vertebrate musculoskeletal system and their wings contain bones and muscles and thus, they may be capable of both actively flipping and twisting their wings. To investigate this issue, we constructed a hummingbird wing model and study its pitching dynamics. The wing kinematics are reconstructed from high-speed imaging data, and the inertial torques are calculated in a rotating frame of reference using mass distribution data measured from dissections of hummingbird wings. Pressure data from a previous CFD study of the same wing kinematics are used to calculate the aerodynamic torque. The results show that like insect wings, the hummingbird wing pitching is driven by its own inertia during reversal, and the aerodynamic torque is responsible for wing twist during mid-stroke. In conclusion, our study suggests that their wing dynamics are very similar even though their actuation systems are entirely different. This research was supported by the NSF.

  5. On the vein-stiffening membrane structure of a dragonfly hind wing

    Institute of Scientific and Technical Information of China (English)

    Zhong-xue LI; Wei SHEN; Gen-shu TONG; Jia-meng TIAN; Loc VU-QUOC

    2009-01-01

    Aiming at exploring the excellent structural performance of the vein-stiffening membrane structure of dragonfly hind wings, we analyzed two planar computational models and three 3D computational models with cambered corrugation based on the finite element method. It is shown that the vein size in different zones is proportional to the magnitude of the vein internal force when the wing structure is subjected to uniform out-of-plane transverse loading. The membrane contributes little to the flexural stiffness of the planar wing models, while exerting an immense impact upon the stiffness of the 3D wing models with cambered corrugation. If a lumped mass of 10% of the wing is fixed on the leading edge close to the wing tip, the wing fundamental fre-quency decreases by 10.7%~13.2%; ifa lumped mass is connected to the wing via multiple springs, the wing fundamental fre-quency decreases by 16.0%~18.0%. Such decrease in fundamental frequency explains the special function of the wing pterostigma in alleviating the wing quivering effect. These particular features of dragonfly wings can be mimicked in the design of new-style reticulately stiffening thin-walled roof systems and flapping wings in novel intelligent aerial vehicles.

  6. Heat transfer investigation of two Langley Research Center delta wing configurations at a Mach number of 10.5, volume 1

    Science.gov (United States)

    Eaves, R. H.; Buchanan, T. D.; Warmbrod, J. D.; Johnson, C. B.

    1972-01-01

    Heat transfer tests for two delta wing configurations were conducted in the hypervelocity wind tunnel. The 24-inch long models were tested at a Mach number of approximately 10.5 and at angles of attack of 20, 40, and 60 degrees over a length Reynolds number range from 5 million to 23 million on 4 May to 4 June 1971. Heat transfer results were obtained from model surface heat gage measurements and thermographic phosphor paint.

  7. Silencing abnormal wing disc gene of the Asian citrus psyllid, Diaphorina citri disrupts adult wing development and increases nymph mortality.

    Directory of Open Access Journals (Sweden)

    Ibrahim El-Shesheny

    Full Text Available Huanglongbing (HLB causes considerable economic losses to citrus industries worldwide. Its management depends on controlling of the Asian citrus Psyllid (ACP, the vector of the bacterium, Candidatus Liberibacter asiaticus (CLas, the causal agent of HLB. Silencing genes by RNA interference (RNAi is a promising tool to explore gene functions as well as control pests. In the current study, abnormal wing disc (awd gene associated with wing development in insects is used to interfere with the flight of psyllids. Our study showed that transcription of awd is development-dependent and the highest level was found in the last instar (5(th of the nymphal stage. Micro-application (topical application of dsRNA to 5(th instar of nymphs caused significant nymphal mortality and adult wing-malformation. These adverse effects in ACP were positively correlated with the amounts of dsRNA used. A qRT-PCR analysis confirmed the dsRNA-mediated transcriptional down-regulation of the awd gene. Significant down-regulation was required to induce a wing-malformed phenotype. No effect was found when dsRNA-gfp was used, indicating the specific effect of dsRNA-awd. Our findings suggest a role for awd in ACP wing development and metamorphosis. awd could serve as a potential target for insect management either via direct application of dsRNA or by producing transgenic plants expressing dsRNA-awd. These strategies will help to mitigate HLB by controlling ACP.

  8. Effect of leading- and trailing-edge flaps on clipped delta wings with and without wing camber at supersonic speeds

    Science.gov (United States)

    Hernandez, Gloria; Wood, Richard M.; Covell, Peter F.

    1994-01-01

    An experimental investigation of the aerodynamic characteristics of thin, moderately swept fighter wings has been conducted to evaluate the effect of camber and twist on the effectiveness of leading- and trailing-edge flaps at supersonic speeds in the Langley Unitary Plan Wind Tunnel. The study geometry consisted of a generic fuselage with camber typical of advanced fighter designs without inlets, canopy, or vertical tail. The model was tested with two wing configurations an uncambered (flat) wing and a cambered and twisted wing. Each wing had an identical clipped delta planform with an inboard leading edge swept back 65 deg and an outboard leading edge swept back 50 deg. The trailing edge was swept forward 25 deg. The leading-edge flaps were deflected 4 deg to 15 deg, and the trailing-edge flaps were deflected from -30 deg to 10 deg. Longitudinal force and moment data were obtained at Mach numbers of 1.60, 1.80, 2.00, and 2.16 for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.16 x 10(exp 6) per foot and for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.0 x 10(exp 6) per foot. Vapor screen, tuft, and oil flow visualization data are also included.

  9. Temperature Distribution Measurement of The Wing Surface under Icing Conditions

    Science.gov (United States)

    Isokawa, Hiroshi; Miyazaki, Takeshi; Kimura, Shigeo; Sakaue, Hirotaka; Morita, Katsuaki; Japan Aerospace Exploration Agency Collaboration; Univ of Notre Dame Collaboration; Kanagawa Institute of Technology Collaboration; Univ of Electro-(UEC) Team, Comm

    2016-11-01

    De- or anti-icing system of an aircraft is necessary for a safe flight operation. Icing is a phenomenon which is caused by a collision of supercooled water frozen to an object. For the in-flight icing, it may cause a change in the wing cross section that causes stall, and in the worst case, the aircraft would fall. Therefore it is important to know the surface temperature of the wing for de- or anti-icing system. In aerospace field, temperature-sensitive paint (TSP) has been widely used for obtaining the surface temperature distribution on a testing article. The luminescent image from the TSP can be related to the temperature distribution. (TSP measurement system) In icing wind tunnel, we measured the surface temperature distribution of the wing model using the TSP measurement system. The effect of icing conditions on the TSP measurement system is discussed.

  10. Application of variable-sweep wings to commuter aircraft

    Science.gov (United States)

    Robins, A. W.; Beissner, F. L., Jr.; Lovell, W. A.; Price, J. E.; Turriiziani, R. V.; Washburn, F. F.

    1983-01-01

    The effects of using variable-sweep wings on the riding quality and mission-performance characteristics of commuter-type aircraft were studied. A fixed-wing baseline vehicle and a variable-sweep version of the baseline were designed and evaluated. Both vehicles were twin-turboprop, pressurized-cabin, 30-passenger commuter aircraft with identical mission requirements. Mission performance was calculated with and without various ride-quality constraints for several combinations of cruise altitude and stage lengths. The variable-sweep aircraft had a gross weight of almost four percent greater than the fixed-wing baseline in order to meet the design-mission requirements. In smooth air, the variable sweep configuration flying with low sweep had a two to three percent fuel-use penalty. However, the imposition of quality constraints in rough air can result in advantages in both fuel economy and flight time for the variable-sweep vehicle flying with high sweep.

  11. Non-linear dynamics of wind turbine wings

    DEFF Research Database (Denmark)

    Larsen, Jesper Winther; Nielsen, Søren R.K.

    2006-01-01

    by the rotation of the aerodynamic load and the curvature, as well as inertial induced non-linearities caused by the support point motion. The non-linear partial differential equations of motion in the moving frame of reference have been discretized, using the fixed base eigenmodes as a functional basis......The paper deals with the formulation of non-linear vibrations of a wind turbine wing described in a wing fixed moving coordinate system. The considered structural model is a Bernoulli-Euler beam with due consideration to axial twist. The theory includes geometrical non-linearities induced....... Important non-linear couplings between the fundamental blade mode and edgewise modes have been identified based on a resonance excitation of the wing, caused by a harmonically varying support point motion with the circular frequency omega. Assuming that the fundamental blade and edgewise eigenfrequencies...

  12. High Performance Piezoelectric Actuators and Wings for Nano Air Vehicles

    Science.gov (United States)

    2012-08-26

    video , and lift is measured using a force transducer coupled with a specially designed apparatus. Many piezoelectrically actuated flapping wing...2.3 Modeling FL øA øB ö mR Lg R yT m gF FT (c) Front View (d) Right Side View(b) Left Side View (a) Top View rcgxö kT c rcp ,xxr rcp ,y z xy y xz y x z y...wing reference frame by the rotation 25 á -ø z y y´ g v z´ rcp ,y F CP ô Figure 2.3.2. Aerodynamic forces on the wings(adapted from Andersen et. al. [61

  13. Leading-edge vortex shedding from rotating wings

    CERN Document Server

    Kolomenskiy, Dmitry; Schneider, Kai

    2014-01-01

    The paper presents a numerical investigation of the leading-edge vortices generated by rotating triangular wings at Reynolds number $Re=250$. A series of three-dimensional numerical simulations have been carried out using a Fourier pseudo-spectral method with volume penalization. The transition from stable attachment of the leading-edge vortex to periodic vortex shedding is explored, as a function of the wing aspect ratio and the angle of attack. It is found that, in a stable configuration, the spanwise flow in the recirculation bubble past the wing is due to the centrifugal force, incompressibility and viscous stresses. For the flow outside of the bubble, an inviscid model of spanwise flow is presented.

  14. Trajectory tracking of an underactuated fixed-wing UAV

    Science.gov (United States)

    Oland, Espen; Kristiansen, Raymond

    2014-12-01

    This paper presents a solution to the problem of trajectory tracking for a fixed-wing UAV. With its inherent actuator constraints, a fixed-wing UAV is not able to track an arbitrary trajectory, such that a guidance scheme is required in order to solve the trajectory tracking problem. In this paper, this is solved by first designing a virtual saturated control law that makes the position and velocity errors go to zero. Then the outputs from the virtual control law are mapped onto actuated variables that can be tracked using the available actuators. To that end, a model-based proportional speed controller and a quaternion-based sliding surface controller are presented, making all the errors go to zero. The solution is proved using Lyapunov theory and is validated through simulations where a fixed-wing UAV tracks a circular trajectory.

  15. HYDRODYNAMICS OF OSCILLATING WING ON THE PITCH ANGLE

    Directory of Open Access Journals (Sweden)

    Vitalii Korobov

    2017-07-01

    Full Text Available Purpose: research of the hydrodynamic characteristics of a wing in a nonstationary stream. Methods: The experimental studies of the hydrodynamic load acting on the wing of 1.5 elongation, wich harmonically oscillated respect to the transversal axis in the frequency range of 0.2-2.5 Hz. The flow speed in the hydrodynamic tunnel ranged of 0.2-1.5 m/s. Results: The instantaneous values of the coefficients of lift and drag / thrust on the pitch angle at unsteady flow depends on the Strouhal number.Discussion: with increasing oscillation frequency coefficients of hydrodynamic force components significantly higher than the data for the stationary blowing out of the wing.

  16. Surface roughness measurement on a wing aircraft by speckle correlation.

    Science.gov (United States)

    Salazar, Félix; Barrientos, Alberto

    2013-09-05

    The study of the damage of aeronautical materials is important because it may change the microscopic surface structure profiles. The modification of geometrical surface properties can cause small instabilities and then a displacement of the boundary layer. One of the irregularities we can often find is surface roughness. Due to an increase of roughness and other effects, there may be extra momentum losses in the boundary layer and a modification in the parasite drag. In this paper we present a speckle method for measuring the surface roughness on an actual unmanned aircraft wing. The results show an inhomogeneous roughness distribution on the wing, as expected according to the anisotropic influence of the winds over the entire wing geometry. A calculation of the uncertainty of the technique is given.

  17. Development and Experiments of the Sea-Wing Underwater Glider

    Institute of Scientific and Technical Information of China (English)

    YU Jian-cheng; ZHANG Ai-qun; JIN Wen-ming; CHEN Qi; TIAN Yu; LIU Chong-jie

    2011-01-01

    Underwater gliders,which glide through water columns by use of a pair of wings,are efficient long-distance,long-duration marine environment observatory platforms.The Sea-Wing underwater glider,developed by the Shenyang Institute of Automation,CAS,is designed for the application of deep-sea environment variables observation.The system components,the mechanical design,and the control system design of the Sea-Wing underwater glider are described in this paper.The pitch and roll adjusting models are derived based on the mechanical design,and the adjusting capabilities for the pitch and roll are analyzed according to the models.Field experiments have been carried out for validating the gliding motion and the ability of measuring ocean environment variables.Experimental results of the motion performances of the glider are presented.

  18. A Simple Model of Wings in Heavy-Ion Collisions

    CERN Document Server

    Parikh, Aditya

    2015-01-01

    We create a simple model of heavy ion collisions independent of any generators as a way of investigating a possible source of the wings seen in data. As a first test, we reproduce a standard correlations plot to verify the integrity of the model. We then proceed to test whether an η dependent v2 could be a source of the wings and take projections along multiple Δφ intervals and compare with data. Other variations of the model are tested by having dN/dφ and v2 depend on η as well as including pions and protons into the model to make it more realistic. Comparisons with data seem to indicate that an η dependent v2 is not the main source of the wings.

  19. Environment Identification in Flight using Sparse Approximation of Wing Strain

    CERN Document Server

    Manohar, Krithika; Kutz, J Nathan

    2016-01-01

    This paper addresses the problem of identifying different flow environments from sparse data collected by wing strain sensors. Insects regularly perform this feat using a sparse ensemble of noisy strain sensors on their wing. First, we obtain strain data from numerical simulation of a Manduca sexta hawkmoth wing undergoing different flow environments. Our data-driven method learns low-dimensional strain features originating from different aerodynamic environments using Proper Orthogonal Decomposition (POD) modes in the frequency domain, and leverages compressed sensing and sparse approximation to classify a set of strain frequency signatures using a dictionary of POD modes. This bio-inspired machine learning architecture for dictionary learning and sparse classification permits fewer costly physical strain sensors while being simultaneously robust to sensor noise. A sensor placement algorithm identifies the frequency samples that best separate the different aerodynamic environments in rank-reduced POD feature...

  20. Life after a Humanities Degree

    Science.gov (United States)

    Masola, Athambile

    2016-01-01

    This article explores the experiences of a humanities graduate after leaving the academy. The author considers her own education in light of the historical changes in South Africa's education system. The article is a personal account of the questions and challenges encountered in choosing a humanities degree in a context where a tertiary education…

  1. Aerospace Technology (Aerospace Engineering Degree)

    OpenAIRE

    Tiseira Izaguirre, Andrés Omar; Blanco Rodríguez, David; Carreres Talens, Marcos; Fajardo Peña, Pablo

    2013-01-01

    Apuntes de la asignatura Tecnología Aeroespacial Tiseira Izaguirre, AO.; Blanco Rodríguez, D.; Carreres Talens, M.; Fajardo Peña, P. (2013). Aerospace Technology (Aerospace Engineering Degree). Editorial Universitat Politècnica de València. http://hdl.handle.net/10251/35263.

  2. The Top Theological Degree Producers

    Science.gov (United States)

    Diverse: Issues in Higher Education, 2012

    2012-01-01

    Each year, "Diverse: Issues in Higher Education" publishes a list of the Top 100 producers of associate, bachelor's and graduate degrees awarded to minority students based on research conducted by Dr. Victor M. H. Borden, professor of educational leadership and policy studies at Indiana University Bloomington. This year, for the first…

  3. Real Analytic Machines and Degrees

    CERN Document Server

    Gärtner, Tobias; 10.4204/EPTCS.24.12

    2010-01-01

    We study and compare in two degree-theoretic ways (iterated Halting oracles analogous to Kleene's arithmetical hierarchy and the Borel hierarchy of descriptive set theory) the capabilities and limitations of three models of analytic computation: BSS machines (aka real-RAM) and strongly/weakly analytic machines as introduced by Hotz et. al. (1995).

  4. Extended observer based on adaptive second order sliding mode control for a fixed wing UAV.

    Science.gov (United States)

    Castañeda, Herman; Salas-Peña, Oscar S; León-Morales, Jesús de

    2017-01-01

    This paper addresses the design of attitude and airspeed controllers for a fixed wing unmanned aerial vehicle. An adaptive second order sliding mode control is proposed for improving performance under different operating conditions and is robust in presence of external disturbances. Moreover, this control does not require the knowledge of disturbance bounds and avoids overestimation of the control gains. Furthermore, in order to implement this controller, an extended observer is designed to estimate unmeasurable states as well as external disturbances. Additionally, sufficient conditions are given to guarantee the closed-loop stability of the observer based control. Finally, using a full 6 degree of freedom model, simulation results are obtained where the performance of the proposed method is compared against active disturbance rejection based on sliding mode control.

  5. Nonlinear dynamics approach of modeling the bifurcation for aircraft wing flutter in transonic speed

    DEFF Research Database (Denmark)

    Matsushita, Hiroshi; Miyata, T.; Christiansen, Lasse Engbo

    2002-01-01

    The procedure of obtaining the two-degrees-of-freedom, finite dimensional. nonlinear mathematical model. which models the nonlinear features of aircraft flutter in transonic speed is reported. The model enables to explain every feature of the transonic flutter data of the wind tunnel tests...... conducted at National Aerospace Laboratory in Japan for a high aspect ratio wing. It explains the nonlinear features of the transonic flutter such as the subcritical Hopf bifurcation of a limit cycle oscillation (LCO), a saddle-node bifurcation, and an unstable limit cycle as well as a normal (linear......) flutter condition with its linear pan. At a final procedure of improve a quantitative matching with the test data. the continuation method for analyzing the bifurcation is extensively used....

  6. Application of modern control design methodology to oblique wing research aircraft

    Science.gov (United States)

    Vincent, James H.

    1991-01-01

    A Linear Quadratic Regulator synthesis technique was used to design an explicit model following control system for the Oblique Wing Research Aircraft (OWRA). The forward path model (Maneuver Command Generator) was designed to incorporate the desired flying qualities and response decoupling. The LQR synthesis was based on the use of generalized controls, and it was structured to provide a proportional/integral error regulator with feedforward compensation. An unexpected consequence of this design approach was the ability to decouple the control synthesis into separate longitudinal and lateral directional designs. Longitudinal and lateral directional control laws were generated for each of the nine design flight conditions, and gain scheduling requirements were addressed. A fully coupled 6 degree of freedom open loop model of the OWRA along with the longitudinal and lateral directional control laws was used to assess the closed loop performance of the design. Evaluations were performed for each of the nine design flight conditions.

  7. Concomitant leg injuries in raptors with wing damage : to the editor

    National Research Council Canada - National Science Library

    Buttle, E. Pohlandt

    2004-01-01

    Extracted from text ... To the editor - Aan die redakteur Concomitant leg injuries in raptors with wing damage Juvenile raptors, in their first year, often experience trauma to the wings as they miss their prey or misjudge...

  8. VISCOELASTIC CONSTITUTIVE MODEL RELATED TO DEFORMATION OF INSECT WING UNDER LOADING IN FLAPPING MOTION

    Institute of Scientific and Technical Information of China (English)

    BAO Lin; HU Jin-song; YU Yong-liang; CHENG Peng; XU Bo-qing; TONG Bing-gang

    2006-01-01

    Flexible insect wings deform passively under the periodic loading during flapping flight. The wing flexibility is considered as one of the specific mechanisms on improving insect flight performance. The constitutive relation of the insect wing material plays a key role on the wing deformation, but has not been clearly understood yet. A viscoelastic constitutive relation model was established based on the stress relaxation experiment of a dragonfly wing (in vitro). This model was examined by the finite clement analysis of the dynamic deformation response for a model insect wing under the action of the periodical inertial force in flapping. It is revealed that the viscoelastic constitutive relation is rational to characterize the biomaterial property of insect wings in contrast to the elastic one. The amplitude and form of the passive viscoelastic deformation of the wing is evidently dependent on the viscous parameters in the constitutive relation.

  9. Morphometric Wing Characters as a Tool for Mosquito Identification

    Science.gov (United States)

    Christe, Rafael de Oliveira; Multini, Laura Cristina; Vidal, Paloma Oliveira; Wilk-da-Silva, Ramon; de Carvalho, Gabriela Cristina; Marrelli, Mauro Toledo

    2016-01-01

    Mosquitoes are responsible for the transmission of important infectious diseases, causing millions of deaths every year and endangering approximately 3 billion people around the world. As such, precise identification of mosquito species is crucial for an understanding of epidemiological patterns of disease transmission. Currently, the most common method of mosquito identification relies on morphological taxonomic keys, which do not always distinguish cryptic species. However, wing geometric morphometrics is a promising tool for the identification of vector mosquitoes, sibling and cryptic species included. This study therefore sought to accurately identify mosquito species from the three most epidemiologically important mosquito genera using wing morphometrics. Twelve mosquito species from three epidemiologically important genera (Aedes, Anopheles and Culex) were collected and identified by taxonomic keys. Next, the right wing of each adult female mosquito was removed and photographed, and the coordinates of eighteen digitized landmarks at the intersections of wing veins were collected. The allometric influence was assessed, and canonical variate analysis and thin-plate splines were used for species identification. Cross-validated reclassification tests were performed for each individual, and a Neighbor Joining tree was constructed to illustrate species segregation patterns. The analyses were carried out and the graphs plotted with TpsUtil 1.29, TpsRelw 1.39, MorphoJ 1.02 and Past 2.17c. Canonical variate analysis for Aedes, Anopheles and Culex genera showed three clear clusters in morphospace, correctly distinguishing the three mosquito genera, and pairwise cross-validated reclassification resulted in at least 99% accuracy; subgenera were also identified correctly with a mean accuracy of 96%, and in 88 of the 132 possible comparisons, species were identified with 100% accuracy after the data was subjected to reclassification. Our results showed that Aedes, Culex

  10. Design of a hybrid rocket / inflatable wing UAV

    Science.gov (United States)

    Sudduth, Cory

    This paper discusses the design challenges and development of a UAV that transitions from a rocket, which allows the aircraft to reach a target altitude rapidly, and then deploys an inflatable wing from an enclosed shell in midflight to allow for loitering and surveillance. The wing deployment and transition is tested in static and dynamic environments, while the performance and stability of both the aircraft mode and rocket mode are examined analytically. An in-depth discussion of key components, including the design, analysis and testing, is also included. Designing an UAV that transitions from a high velocity rocket, to a slow velocity UAV provides many difficult and unique design challenges. For example, the incorporation of deployable wing technology into a full UAV system results in many design constraints. In this particular design inflatable wings are used to generate lift during aircraft mode, and the stabilizing fins for the main wing also acted as the fins for the vehicle during its rocket phase. This required the balancing of the two different vehicle configurations to ensure that the aircraft would be able to fly stably in both modes, and transition between them without catastrophic failure. Significant research, and testing went into the finding the best method of storing the inflatable wing, as well as finding the required inflation rate to minimize unsteady aerodynamic affects. Design work was also invested in the development of an inflation system, as it had to be highly reliable, and yet very light weight for use in this small UAV. This paper discusses how these design challenges were overcome, the development and testing of individual sub-components and how they are incorporated into the overall vehicle. The analysis that went into this UAV, as well as methods used to optimize the design in order to minimize weight and maximize the aircraft performance and loitering time is also discussed.

  11. A two-dimensional iterative panel method and boundary layer model for bio-inspired multi-body wings

    Science.gov (United States)

    Blower, Christopher J.; Dhruv, Akash; Wickenheiser, Adam M.

    2014-03-01

    The increased use of Unmanned Aerial Vehicles (UAVs) has created a continuous demand for improved flight capabilities and range of use. During the last decade, engineers have turned to bio-inspiration for new and innovative flow control methods for gust alleviation, maneuverability, and stability improvement using morphing aircraft wings. The bio-inspired wing design considered in this study mimics the flow manipulation techniques performed by birds to extend the operating envelope of UAVs through the installation of an array of feather-like panels across the airfoil's upper and lower surfaces while replacing the trailing edge flap. Each flap has the ability to deflect into both the airfoil and the inbound airflow using hinge points with a single degree-of-freedom, situated at 20%, 40%, 60% and 80% of the chord. The installation of the surface flaps offers configurations that enable advantageous maneuvers while alleviating gust disturbances. Due to the number of possible permutations available for the flap configurations, an iterative constant-strength doublet/source panel method has been developed with an integrated boundary layer model to calculate the pressure distribution and viscous drag over the wing's surface. As a result, the lift, drag and moment coefficients for each airfoil configuration can be calculated. The flight coefficients of this numerical method are validated using experimental data from a low speed suction wind tunnel operating at a Reynolds Number 300,000. This method enables the aerodynamic assessment of a morphing wing profile to be performed accurately and efficiently in comparison to Computational Fluid Dynamics methods and experiments as discussed herein.

  12. Distributed Turboelectric Propulsion for Hybrid Wing Body Aircraft

    Science.gov (United States)

    Kim, Hyun Dae; Brown, Gerald V.; Felder, James L.

    2008-01-01

    Meeting future goals for aircraft and air traffic system performance will require new airframes with more highly integrated propulsion. Previous studies have evaluated hybrid wing body (HWB) configurations with various numbers of engines and with increasing degrees of propulsion-airframe integration. A recently published configuration with 12 small engines partially embedded in a HWB aircraft, reviewed herein, serves as the airframe baseline for the new concept aircraft that is the subject of this paper. To achieve high cruise efficiency, a high lift-to-drag ratio HWB was adopted as the baseline airframe along with boundary layer ingestion inlets and distributed thrust nozzles to fill in the wakes generated by the vehicle. The distributed powered-lift propulsion concept for the baseline vehicle used a simple, high-lift-capable internally blown flap or jet flap system with a number of small high bypass ratio turbofan engines in the airframe. In that concept, the engine flow path from the inlet to the nozzle is direct and does not involve complicated internal ducts through the airframe to redistribute the engine flow. In addition, partially embedded engines, distributed along the upper surface of the HWB airframe, provide noise reduction through airframe shielding and promote jet flow mixing with the ambient airflow. To improve performance and to reduce noise and environmental impact even further, a drastic change in the propulsion system is proposed in this paper. The new concept adopts the previous baseline cruise-efficient short take-off and landing (CESTOL) airframe but employs a number of superconducting motors to drive the distributed fans rather than using many small conventional engines. The power to drive these electric fans is generated by two remotely located gas-turbine-driven superconducting generators. This arrangement allows many small partially embedded fans while retaining the superior efficiency of large core engines, which are physically separated

  13. Electric Loading Simulation System for Missile Wings and Rudders

    Institute of Scientific and Technical Information of China (English)

    QI Rong; LIN Hui; CHEN Ming

    2006-01-01

    The design and the realization of missile wings and rudders loading simulation system based on digital signal processor (DSP) TMS320LF2407 and direct torque control (DTC) servo driver ACS600 are discussed. The structure and opration principle for the system are presented. Speediness and elimination of superabundant torque are two key difficulties for electric loading simulation system. The method which can eliminate the superabundant torque is researched. Test results show the airflow resistance when missile wings and rudders are spreading can be rapidly simulated with high accuracy.

  14. Prediction Approach to Life on Wing for Civil Aeroengine

    Institute of Scientific and Technical Information of China (English)

    RONG Xiang; ZUO Hong-fu; ZHANG Hai-jun

    2008-01-01

    To reduce engine maintenance cost and support safe operation, a prediction method of engine life on wing was proposed. This method is a kind of regression model which is a function of the condition monitoring and failure data. Key causes of engine removals were analyzed, and the life limit due to performance deterioration was predicted by proportional hazards model. Then the scheduled removal causes were considered as constraints of engine life to predicte the final life on wing. Application of the proposed prediction method to the case of CF6-80C2A5 engine fleet in an airline proved its effectiveness.

  15. The Development and Control of Axial Vortices over Swept Wings

    OpenAIRE

    Klute, Sandra M.

    1999-01-01

    The natural unsteadiness in the post-breakdown flowfield of a 75° sweep delta wing at 40° angle of attack was studied with dual and single point hot-wire anemometry in the Engineering Science and Mechanics (ESM) Wind Tunnel at a Reynolds number Re = 210,000. Data were taken in five crossflow planes surrounding the wing's trailing edge. Results showed a dominant narrowband Strouhal frequency of St = 1.5 covering approximately 80% of the area with lower-intensity broadband secondary freque...

  16. Unsteady aerodynamics and flow control for flapping wing flyers

    Science.gov (United States)

    Ho, Steven; Nassef, Hany; Pornsinsirirak, Nick; Tai, Yu-Chong; Ho, Chih-Ming

    2003-11-01

    The creation of micro air vehicles (MAVs) of the same general sizes and weight as natural fliers has spawned renewed interest in flapping wing flight. With a wingspan of approximately 15 cm and a flight speed of a few meters per second, MAVs experience the same low Reynolds number (10 4-10 5) flight conditions as their biological counterparts. In this flow regime, rigid fixed wings drop dramatically in aerodynamic performance while flexible flapping wings gain efficacy and are the preferred propulsion method for small natural fliers. Researchers have long realized that steady-state aerodynamics does not properly capture the physical phenomena or forces present in flapping flight at this scale. Hence, unsteady flow mechanisms must dominate this regime. Furthermore, due to the low flight speeds, any disturbance such as gusts or wind will dramatically change the aerodynamic conditions around the MAV. In response, a suitable feedback control system and actuation technology must be developed so that the wing can maintain its aerodynamic efficiency in this extremely dynamic situation; one where the unsteady separated flow field and wing structure are tightly coupled and interact nonlinearly. For instance, birds and bats control their flexible wings with muscle tissue to successfully deal with rapid changes in the flow environment. Drawing from their example, perhaps MAVs can use lightweight actuators in conjunction with adaptive feedback control to shape the wing and achieve active flow control. This article first reviews the scaling laws and unsteady flow regime constraining both biological and man-made fliers. Then a summary of vortex dominated unsteady aerodynamics follows. Next, aeroelastic coupling and its effect on lift and thrust are discussed. Afterwards, flow control strategies found in nature and devised by man to deal with separated flows are examined. Recent work is also presented in using microelectromechanical systems (MEMS) actuators and angular speed

  17. Wake patterns of the wings and tail of hovering hummingbirds

    Science.gov (United States)

    Altshuler, Douglas L.; Princevac, Marko; Pan, Hansheng; Lozano, Jesse

    The flow fields of slowly flying bats and fasterflying birds differ in that bats produce two vortex loops during each stroke, one per wing, and birds produce a single vortex loop per stroke. In addition, the circulation at stroke transition approaches zero in bats but remains strong in birds. It is unknown if these difference derive from fundamental differences in wing morphology or are a consequence of flight speed. Here, we present an analysis of the horizontal flow field underneath hovering Anna's hummingbirds (Calypte anna) to describe the wake of a bird flying at zero forward velocity. We also consider how the hummingbird tail interacts with the wake generated by the wings. High-speed image recording and analysis from three orthogonal perspectives revealed that the wing tips reach peak velocities in the middle of each stroke and approach zero velocity at stroke transition. Hummingbirds use complex tail kinematic patterns ranging from in phase to antiphase cycling with respect to the wings, covering several phase shifted patterns. We employed particle image velocimetry to attain detailed horizontal flow measurements at three levels with respect to the tail: in the tail, at the tail tip, and just below the tail. The velocity patterns underneath the wings indicate that flow oscillates along the ventral-dorsal axis in response to the down- and up-strokes and that the sideways flows with respect to the bird are consistently from the lateral to medial. The region around the tail is dominated by axial flows in dorsal to ventral direction. We propose that these flows are generated by interaction between the wakes of the two wings at the end of the upstroke, and that the tail actively defects flows to generate moments that contribute to pitch stability. The flow fields images also revealed distinct vortex loops underneath each wing, which were generated during each stroke. From these data, we propose a model for the primary flow structures of hummingbirds that more

  18. Transmittance characteristics of plasmonic graphene ribbons with a wing

    Science.gov (United States)

    Yuan, Lin; Yan, Xin; Wang, Yueke; Sang, Tian; Yang, Guofeng

    2016-09-01

    We numerically investigate the transmittance characteristics of graphene ribbons with a wing by the finite element method. By determining the dispersion relation of edge graphene plasmon (EGP) modes and analyzing the mode distributions, it is considered that the transmission dips originate from the resonances of three EGP modes, namely, the symmetrical EGPs, antisymmetrical EGPs, and EGPs of a semi-infinite sheet. By changing the width and length of the wing, it was further confirmed that transmission dips originate from the EGP modes. Owing to the tunable permittivity of graphene by adjusting the gate voltage, the transmittance dips can be easily tuned.

  19. Aerodynamic Optimization of an Over-the-Wing-Nacelle-Mount Configuration

    OpenAIRE

    Daisuke Sasaki; Kazuhiro Nakahashi

    2011-01-01

    An over-the-wing-nacelle-mount airplane configuration is known to prevent the noise propagation from jet engines toward ground. However, the configuration is assumed to have low aerodynamic efficiency due to the aerodynamic interference effect between a wing and a nacelle. In this paper, aerodynamic design optimization is conducted to improve aerodynamic efficiency to be equivalent to conventional under-the-wing-nacelle-mount configuration. The nacelle and wing geometry are modified to achiev...

  20. Basic research in wake vortex alleviation using a variable twist wing

    Science.gov (United States)

    Morris, D. J.; Holbrook, G. T.

    1981-01-01

    The variable twist wing concept was used to investigate the relative effects of lift and turbulence distribution on the rolled up vortex wake. Several methods of reducing the vortex strength behind an aircraft were identified. These involve the redistribution of lift spanwise on the wing and drag distribution along the wing. Initial attempts to use the variable twist wing velocity data to validate the WAKE computer code have shown a strong correlation, although the vorticity levels were not exactly matched.

  1. Modeling Interactions Between Flexible Flapping Wing Spars, Mechanisms, and Drive Motors

    Science.gov (United States)

    2011-09-01

    flapping wing spars. The model can be used to examine the coupled system-level behavior of brushed DC motors , gear trains, and any number of linkages and...mechanisms consist of a brushed DC motor and gear train in combination with linkage elements, flexible wing spars, and wing surfaces. The aerodynamic and...characteristics of the motion of flexible wing spars that are driven by ornithopter linkages and brushed DC motors . There are three principal types of

  2. Power reduction and the radial limit of stall delay in revolving wings of different aspect ratio

    NARCIS (Netherlands)

    Kruyt, J.W.; Heijst, Van G.F.; Altshuler, D.L.; Lentink, David

    2015-01-01

    Airplanes and helicopters use high aspect ratio wings to reduce the power required to fly, but must operate at low angle of attack to prevent flow separation and stall. Animals capable of slow sustained flight, such as hummingbirds, have low aspect ratio wings and flap their wings at high angle o

  3. 78 FR 3356 - Airworthiness Directives; Various Aircraft Equipped With Wing Lift Struts

    Science.gov (United States)

    2013-01-16

    ... Directives; Various Aircraft Equipped With Wing Lift Struts AGENCY: Federal Aviation Administration (FAA... airworthiness directive (AD) that applies to certain aircraft equipped with wing lift struts. The existing AD... Joint Aircraft System Component (JASC)/Air Transport Association (ATA) of America Code 57, Wings....

  4. 14 CFR 45.25 - Location of marks on fixed-wing aircraft.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Location of marks on fixed-wing aircraft... TRANSPORTATION AIRCRAFT IDENTIFICATION AND REGISTRATION MARKING Nationality and Registration Marks § 45.25 Location of marks on fixed-wing aircraft. (a) The operator of a fixed-wing aircraft shall display...

  5. 78 FR 73997 - Airworthiness Directives; Various Aircraft Equipped with Wing Lift Struts

    Science.gov (United States)

    2013-12-10

    .... SUMMARY: We are revising Airworthiness Directive (AD) 99-01-05 for certain aircraft equipped with wing... unseal a sealed wing lift strut should be coordinated with the Atlanta Aircraft Certification Office (ACO...)(2) of this AD that occurs later, remove the wing lift struts following Piper Aircraft...

  6. Calculation of wing spars of variable cross-section and linear load

    Science.gov (United States)

    Kirste, Leon

    1925-01-01

    The calculation of wing spars of constant cross-section and load has been thoroughly treated by a large number of authors. Such is not the case,however, regarding the calculation of wing spars whose section and linear load diminish toward the ends, as in wings of trapezoidal contour and decreasing section.

  7. Flapping wing actuation using resonant compliant mechanisms: An insect-inspired design

    NARCIS (Netherlands)

    Bolsman, C.T.

    2010-01-01

    The realization of a wing actuation mechanism for a flapping wing micro air vehicle requires a move away from traditional designs based on gears and links. An approach inspired by nature’s flyers is better suited. For flapping flight two wing motions are important: the sweeping and the pitching moti

  8. File list: ALL.Lar.50.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Lar.50.AllAg.Imaginal_wing_disc dm3 All antigens Larvae Imaginal wing disc SRX6...RX026744,SRX152099 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Lar.50.AllAg.Imaginal_wing_disc.bed ...

  9. File list: ALL.Lar.05.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Lar.05.AllAg.Imaginal_wing_disc dm3 All antigens Larvae Imaginal wing disc SRX1...RX131079,SRX182777,SRX131083,SRX131084 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Lar.05.AllAg.Imaginal_wing_disc.bed ...

  10. File list: Pol.Lar.05.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Lar.05.AllAg.Imaginal_wing_disc dm3 RNA polymerase Larvae Imaginal wing disc SR...X026743,SRX026742,SRX182775,SRX661503 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Pol.Lar.05.AllAg.Imaginal_wing_disc.bed ...

  11. File list: Unc.Lar.20.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Lar.20.AllAg.Imaginal_wing_disc dm3 Unclassified Larvae Imaginal wing disc http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Unc.Lar.20.AllAg.Imaginal_wing_disc.bed ...

  12. File list: His.Lar.05.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Lar.05.AllAg.Imaginal_wing_disc dm3 Histone Larvae Imaginal wing disc SRX661498...00 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.05.AllAg.Imaginal_wing_disc.bed ...

  13. File list: Pol.Lar.50.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Lar.50.AllAg.Imaginal_wing_disc dm3 RNA polymerase Larvae Imaginal wing disc SR...X026743,SRX661503,SRX026742,SRX182775 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Pol.Lar.50.AllAg.Imaginal_wing_disc.bed ...

  14. File list: Pol.Lar.20.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Lar.20.AllAg.Imaginal_wing_disc dm3 RNA polymerase Larvae Imaginal wing disc SR...X026743,SRX661503,SRX026742,SRX182775 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Pol.Lar.20.AllAg.Imaginal_wing_disc.bed ...

  15. File list: His.Lar.20.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Lar.20.AllAg.Imaginal_wing_disc dm3 Histone Larvae Imaginal wing disc SRX661498...00 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.20.AllAg.Imaginal_wing_disc.bed ...

  16. File list: Unc.Lar.05.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Lar.05.AllAg.Imaginal_wing_disc dm3 Unclassified Larvae Imaginal wing disc http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Unc.Lar.05.AllAg.Imaginal_wing_disc.bed ...

  17. File list: His.Lar.50.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Lar.50.AllAg.Imaginal_wing_disc dm3 Histone Larvae Imaginal wing disc SRX661498...00 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.50.AllAg.Imaginal_wing_disc.bed ...

  18. File list: Unc.Lar.10.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Lar.10.AllAg.Imaginal_wing_disc dm3 Unclassified Larvae Imaginal wing disc http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Unc.Lar.10.AllAg.Imaginal_wing_disc.bed ...

  19. File list: ALL.Lar.20.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Lar.20.AllAg.Imaginal_wing_disc dm3 All antigens Larvae Imaginal wing disc SRX6...RX187588,SRX026744,SRX131079,SRX131080 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Lar.20.AllAg.Imaginal_wing_disc.bed ...

  20. File list: ALL.Lar.10.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ALL.Lar.10.AllAg.Imaginal_wing_disc dm3 All antigens Larvae Imaginal wing disc SRX6...RX182774,SRX131083,SRX661500,SRX187588 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/ALL.Lar.10.AllAg.Imaginal_wing_disc.bed ...

  1. File list: Pol.Lar.10.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Pol.Lar.10.AllAg.Imaginal_wing_disc dm3 RNA polymerase Larvae Imaginal wing disc SR...X026742,SRX661503,SRX026743,SRX182775 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Pol.Lar.10.AllAg.Imaginal_wing_disc.bed ...

  2. File list: Unc.Lar.50.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Unc.Lar.50.AllAg.Imaginal_wing_disc dm3 Unclassified Larvae Imaginal wing disc http...://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/Unc.Lar.50.AllAg.Imaginal_wing_disc.bed ...

  3. File list: His.Lar.10.AllAg.Imaginal_wing_disc [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Lar.10.AllAg.Imaginal_wing_disc dm3 Histone Larvae Imaginal wing disc SRX661498...00 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/assembled/His.Lar.10.AllAg.Imaginal_wing_disc.bed ...

  4. Power reduction and the radial limit of stall delay in revolving wings of different aspect ratio

    NARCIS (Netherlands)

    Kruyt, J.W.; Heijst, Van G.F.; Altshuler, D.L.; Lentink, David

    2015-01-01

    Airplanes and helicopters use high aspect ratio wings to reduce the power required to fly, but must operate at low angle of attack to prevent flow separation and stall. Animals capable of slow sustained flight, such as hummingbirds, have low aspect ratio wings and flap their wings at high angle o

  5. 77 FR 50062 - Safety Zone; Embry-Riddle Wings and Waves, Atlantic Ocean; Daytona Beach, FL

    Science.gov (United States)

    2012-08-20

    ... SECURITY Coast Guard 33 CFR Part 165 RIN 1625-AA00 Safety Zone; Embry-Riddle Wings and Waves, Atlantic... Daytona Beach, Florida during the Embry-Riddle Wings and Waves air show. The event is scheduled to take...: Sec. 165.T07-0653 Safety Zone; Embry Riddle Wings and Waves, Atlantic Ocean, Daytona Beach, FL. (a...

  6. Exploring and exploiting natural variation in the wings of a predatory ladybird beetle for biological control

    NARCIS (Netherlands)

    Lommen, Suzanne Theresia Esther

    2013-01-01

    The central theme of this PhD thesis is natural variation in the wing length of the predatory two-spot ladybird beetle, Adalia bipunctata. ‘Wingless’ individuals of this species occur occasionally. They possess truncated wing covers and flight wings and cannot fly, but the extent of the reduction is

  7. Note on the glide of a bird with wings bent downwards

    NARCIS (Netherlands)

    Sparenberg, J. A.

    2006-01-01

    This note considers the influence of the bending down of the wings of a bird on the performance of its glide. The induced drag of bent wings is compared with the induced drag of a corresponding straight wing. Numerical results are given.

  8. Improvement of hang glider performance by use of ultralight elastic wing

    Science.gov (United States)

    Wolf, J. S.

    1979-01-01

    The problem of the lateral controllability of the hang glider by the pilot's weight shift was considered. The influence of the span and the torsional elasticity of the wing was determined. It was stated that an ultralight elastic wing of a new kind was most suitable for good control. The wing also has other advantageous properties.

  9. Experimental Methods to Characterize Nonlinear Vibration of Flapping Wing Micro Air Vehicles

    Science.gov (United States)

    2007-03-01

    the following terminology when referring to flapping wing MAVs; bird flight machines are also known as ornithopters and robotic insects are also...15. SUBJECT TERMS Flapping Wing Micro Air Vehicle, flapping-wing MAV, MAV, ornithopter , entomopter, nonlinear vibration, beam resonance

  10. Wing-Alone Aerodynamic Characteristics to High Angles of Attack at Subsonic and Transonic Speeds.

    Science.gov (United States)

    1982-11-01

    indicators of symmetry since the wings were unbanked within the limits of tolerances and flow angularity. Longitudinal, spanwise, and vertical... unbanked wings at subsonic and transonic speeds from low to high angles of attack. The wing planforms varied in aspect ratio and taper ratio with

  11. Reynolds Number Effects on Thrust Coefficients and PIV for Flapping Wing Micro Air Vehicles

    Science.gov (United States)

    2012-03-09

    increase the resonant frequency of the thorax, the wing inertia was reduced by fabricating the wings with carbon fiber wing spars. R. J. Wood...and Electronics Engineers Transaction on Robotics, Vol. 24, No. 2, April 2008. Zbikowski, R., Galinski, C., Pedersen , C.B., “Four-Bar Linkage

  12. Project Sekwa: A variable stability, blended-wing-body, research UAV

    CSIR Research Space (South Africa)

    Broughton, BA

    2008-10-01

    Full Text Available of flying wing and Blended-Wing-Body (BWB) platforms. The main objective of the project was to investigate the advantages and pitfalls of relaxing the longitudinal stability criteria on a Blended-Wing-Body UAV. The project was also aimed at expanding...

  13. Note on the glide of a bird with wings bent downwards

    NARCIS (Netherlands)

    Sparenberg, J. A.

    This note considers the influence of the bending down of the wings of a bird on the performance of its glide. The induced drag of bent wings is compared with the induced drag of a corresponding straight wing. Numerical results are given.

  14. Six degree of freedom sensor

    Science.gov (United States)

    Vann, Charles S.

    1999-01-01

    This small, non-contact optical sensor increases the capability and flexibility of computer controlled machines by detecting its relative position to a workpiece in all six degrees of freedom (DOF). At a fraction of the cost, it is over 200 times faster and up to 25 times more accurate than competing 3-DOF sensors. Applications range from flexible manufacturing to a 6-DOF mouse for computers. Until now, highly agile and accurate machines have been limited by their inability to adjust to changes in their tasks. By enabling them to sense all six degrees of position, these machines can now adapt to new and complicated tasks without human intervention or delay--simplifying production, reducing costs, and enhancing the value and capability of flexible manufacturing.

  15. Degree 3 Networks Topological Routing

    DEFF Research Database (Denmark)

    Gutierrez Lopez, Jose Manuel; Riaz, M. Tahir; Pedersen, Jens Myrup;

    2009-01-01

    Topological routing is a table free alternative to traditional routing methods. It is specially well suited for organized network interconnection schemes. Topological routing algorithms correspond to the type O(1), constant complexity, being very attractive for large scale networks. It has been...... proposed for many topologies and this work compares the algorithms for three degree three topologies using a more analytical approach than previous studies....

  16. Study on flow over finite wing with respect to F-22 raptor, Supermarine Spitfire, F-7 BG aircraft wing and analyze its stability performance and experimental values

    Science.gov (United States)

    Ali, Md. Nesar; Alam, Mahbubul

    2017-06-01

    A finite wing is a three-dimensional body, and consequently the flow over the finite wing is three-dimensional; that is, there is a component of flow in the span wise direction. The physical mechanism for generating lift on the wing is the existence of a high pressure on the bottom surface and a low pressure on the top surface. The net imbalance of the pressure distribution creates the lift. As a by-product of this pressure imbalance, the flow near the wing tips tends to curl around the tips, being forced from the high-pressure region just underneath the tips to the low-pressure region on top. This flow around the wing tips is shown in the front view of the wing. As a result, on the top surface of the wing, there is generally a span wise component of flow from the tip toward the wing root, causing the streamlines over the top surface to bend toward the root. On the bottom surface of the wing, there is generally a span wise component of flow from the root toward the tip, causing the streamlines over the bottom surface to bend toward the tip. Clearly, the flow over the finite wing is three-dimensional, and therefore we would expect the overall aerodynamic properties of such a wing to differ from those of its airfoil sections. The tendency for the flow to "leak" around the wing tips has another important effect on the aerodynamics of the wing. This flow establishes a circulatory motion that trails downstream of the wing; that is, a trailing vortex is created at each wing tip. The aerodynamics of finite wings is analyzed using the classical lifting line model. This simple model allows a closed-form solution that captures most of the physical effects applicable to finite wings. The model is based on the horseshoe-shaped vortex that introduces the concept of a vortex wake and wing tip vortices. The downwash induced by the wake creates an induced drag that did not exist in the two-dimensional analysis. Furthermore, as wingspan is reduced, the wing lift slope decreases

  17. Surfzone monitoring using rotary wing unmanned aerial vehicles

    NARCIS (Netherlands)

    Brouwer, R.L.; De Schipper, M.A.; Rynne, P.F.; Graham, F.J.; Reniers, A.J.H.M.; Macmahan, J.H.

    2015-01-01

    This study investigates the potential of rotary wing unmanned aerial vehicles (UAVs) to monitor the surfzone. This paper shows that these UAVs are extremely flexible surveying platforms that can gather nearcontinuous moderate spatial resolution and high temporal resolution imagery from a fixed posit

  18. Flow visualization of swept wing boundary layer transition

    NARCIS (Netherlands)

    Serpieri, J.; Kotsonis, M.

    2015-01-01

    In this work the flow visualization of the transition pattern occurring on a swept wing in a subsonic flow is presented. This is done by means of fluorescent oil flow technique and boundary layer hot-wire scans. The experiment was performed at Reynolds number of 2:15 . 106 and at angle of attack of

  19. Design and Control of Flapping Wing Micro Air Vehicles

    Science.gov (United States)

    2011-09-01

    Bar-Cohen, Y., Electroactive Polymer Actuators as Artificial Muscles: Reality, Potential and Challenges, International Society for Optical Engineering ...In 2004 he was assigned to the Air Force Academy where he taught courses in structures, dynamics, mechatronics and engineering design while...WING MICRO AIR VEHICLES DISSERTATION Presented to the Faculty Department of Aeronautics and Astronautics Graduate School of Engineering and

  20. Flight mechanics of a tailless articulated wing aircraft.

    Science.gov (United States)

    Paranjape, Aditya A; Chung, Soon-Jo; Selig, Michael S

    2011-06-01

    This paper investigates the flight mechanics of a micro aerial vehicle without a vertical tail in an effort to reverse-engineer the agility of avian flight. The key to stability and control of such a tailless aircraft lies in the ability to control the incidence angles and dihedral angles of both wings independently. The dihedral angles can be varied symmetrically on both wings to control aircraft speed independently of the angle of attack and flight path angle, while asymmetric dihedral can be used to control yaw in the absence of a vertical stabilizer. It is shown that wing dihedral angles alone can effectively regulate sideslip during rapid turns and generate a wide range of equilibrium turn rates while maintaining a constant flight speed and regulating sideslip. Numerical continuation and bifurcation analysis are used to compute trim states and assess their stability. This paper lays the foundation for design and stability analysis of a flapping wing aircraft that can switch rapidly from flapping to gliding flight for agile manoeuvring in a constrained environment.

  1. Investigating Biological Controls to Suppress Spotted Wing Drosophila Populations

    Science.gov (United States)

    The spotted wing drosophila has become a major cherry pest in California. To develop sustainable management options for this highly mobile pest, we worked with cooperators at Oregon State University and the USDA to discover and import natural enemies of the fly from its native range in South Korea ...

  2. Design of a new tandem wings hybrid airship

    Science.gov (United States)

    Li, Feng; Ye, ZhengYin; Gao, Chao

    2012-10-01

    It is scientifically important science value and engineering promising to develop the buoyancy-lift integrated hybrid airship for high attitude platform. Through the numerical method, a new tandem wings hybrid airship with both higher utility value and economy efficiency was obtained and its total performance and technical parameters were analyzed in detail. In order to further improve the lift-drag characteristics, we implemented the optimization design for aerodynamic configuration of tandem wings hybrid airship via the response surface method. The results indicate that the tandem wings hybrid airship has considerable volume efficiency and higher aerodynamic characteristics. After optimization, the lift-drag ratio of this hybrid airship was increased by 6.08%. In a given gross lift condition, tandem wings hybrid airship may provide more payload and specific productivity. Furthermore, the size of tandem airship is smaller so the demand for skin flexible materials can be reduced. Results of this study could serve as a new approach to designing buoyancy-lifting integrated hybrid airship.

  3. Rotational accelerations stabilize leading edge vortices on revolving fly wings

    NARCIS (Netherlands)

    Lentink, D.; Dickinson, M.H.

    2009-01-01

    The aerodynamic performance of hovering insects is largely explained by the presence of a stably attached leading edge vortex (LEV) on top of their wings. Although LEVs have been visualized on real, physically modeled, and simulated insects, the physical mechanisms responsible for their stability

  4. Dynamics of Micro-Air-Vehicle with Flapping Wings

    Directory of Open Access Journals (Sweden)

    K. Sibilski

    2004-01-01

    Full Text Available Small (approximately 6 inch long, or hand-held reconnaissance micro air vehicles (MAVs will fly inside buildings, and require hover for observation, and agility at low speeds to move in confined spaces. For this flight envelope insect-like flapping wings seem to be an optimal mode of flying. Investigation of the aerodynamics of flapping wing MAVs is very challenging. The problem involves complex unsteady, viscous flow (mainly laminar, with the moving wing generating vortices and interacting with them. At this early stage of research only a preliminary insight into the nature of the little known aerodynamics of MAVs has been obtained. This paper describes computational models for simulation of the controlled motion of a microelectromechanical flying insect – entomopter. The design of software simulation for entomopter flight (SSEF is presented. In particular, we will estimate the flight control algorithms and performance for a Micromechanical Flying Insect (MFI, a 80–100 mm (wingtip-to-wingtip device capable of sustained autonomous flight. The SSEF is an end-to-end tool composed of several modular blocks which model the wing aerodynamics and dynamics, the body dynamics, and in the future, the environment perception, control algorithms, the actuators dynamics, and the visual and inertial sensors. We present the current state of the art of its implementation, and preliminary results. 

  5. Rotational accelerations stabilize leading edge vortices on revolving fly wings

    NARCIS (Netherlands)

    Lentink, D.; Dickinson, M.H.

    2009-01-01

    The aerodynamic performance of hovering insects is largely explained by the presence of a stably attached leading edge vortex (LEV) on top of their wings. Although LEVs have been visualized on real, physically modeled, and simulated insects, the physical mechanisms responsible for their stability ar

  6. Electric Propulsion Concepts for an Inverted Joined Wing Airplane Demonstrator

    Directory of Open Access Journals (Sweden)

    Cezary Galinski

    2017-05-01

    Full Text Available One of the airplane design concepts that potentially allows for significantly increased efficiency, but has not yet been investigated thoroughly, is the inverted joined wing configuration, where the upper wing is positioned in front of the lower one. We performed wind tunnel and flight testing of a demonstrator of this concept, first by applying electrical propulsion to simplify wind tunnel testing, and then the same electrical-propulsion demonstrator performed several flights. As the chosen propulsion method proved to be too cumbersome for an intensive flight campaign and significant loss of battery performance was also observed, the electrical propulsion was then replaced by internal combustion propulsion in the second phase, involving longer-duration flight testing. Next we identified and analyzed two potentially beneficial modifications to the design tested: one involved shifting the center of gravity towards the aft, the other involved modifying the thrust vector position, both with the assumption that electric motors can be applied for propulsion. On this basis, the paper finishes with some conclusions concerning a new concept of electrical propulsion for an inverted joined wing design, combining two ideas: hybridization and distribution along the aft wing leading edge.

  7. An inflatable wing using the principle of Tensairity

    NARCIS (Netherlands)

    Breuer, J.; Ockels, W.; Luchsinger, R.H.

    2007-01-01

    The paper describes the new concept Tensairity which can be used to significantly improve the load bearing capacity of inflatable wings. The basic principle of Tensairity is to use an inflatable structure to stabilize conventional compression and tension elements. So far, Tensairity has been mainly

  8. Robust Backstepping Control of Wing Rock Using Disturbance Observer

    Directory of Open Access Journals (Sweden)

    Dawei Wu

    2017-02-01

    Full Text Available Wing rock is a highly nonlinear phenomenon when the aircraft suffers undesired roll-dominated oscillatory at high angle of attack (AOA. Considering the strong nonlinear and unsteady aerodynamic characteristics, an uncertain multi-input and multi-output (MIMO nonlinear wing rock model is studied, and system uncertainties, unsteady aerodynamic disturbances and externaldisturbancesareconsideredinthedesignofwingrockcontrollaw. Tohandletheproblemof multipledisturbances,arobustcontrolschemeisproposedbasedontheextendedstateobserver(ESO and the radial basis function neural network (RBFNN technique. Considering that the effectiveness of actuators are greatly decreased at high AOA, the input saturation problem is also handled by constructing a corresponding auxiliary system. Based on the improved ESO and the auxiliary system, a robust backstepping control law is proposed for the wing rock control. In addition, the dynamic surface control (DSC technique is introduced to avoid the tedious computations of time derivatives for the virtual control laws in the backstepping method. The stability of the closed-loop system is guaranteed via rigorously Lyapunov analysis. Finally, simulation results are presented to illustrate the effectiveness of the ESO and the proposed wing rock control approach.

  9. Numerical Characterization of a Composite Bonded Wing-Box

    Science.gov (United States)

    Smeltzer, Stanley S., III; Lovejoy, Andrew E.; Satyanarayana, Arunkumar

    2008-01-01

    The development of composite wing structures has focused on the use of mechanical fasteners to join heavily-loaded areas, while bonded joints have been used only for select locations. The focus of this paper is the examination of the adhesive layer in a generic bonded wing box that represents a "fastenerless" or unitized structure in order to characterize the general behavior and failure mechanisms. A global/local approach was applied to study the response of the adhesive layer using a global shell model and a local shell/solid model. The wing box was analyzed under load to represent a high-g up-bending condition such that the strains in the composite sandwich face sheets are comparable to an expected design allowable. The global/local analysis indicates that at these wing load levels the strains in the adhesive layer are well within the adhesive's elastic region, such that yielding would not be expected in the adhesive layer. The global/local methodology appears to be a promising approach to evaluate the structural integrity of the adhesively bonded structures.

  10. A Fixed-Wing Micro Air Vehicle with Hovering Capability

    Science.gov (United States)

    2010-12-01

    a 3D geometry of the aircraft, a CAD design method developed by Dassault Aviation, CATIA V5, has been used. Figure 3 describes the overall sketching...to design in CATIA After creating all basic parts which consist of wing, body, fin, propeller, motor mounting system, all parts are assembled

  11. Passive Gust Alleviation for a Flying Wing Aircraft

    Science.gov (United States)

    2013-01-10

    66 E.1 CATIA Surface Model...with 20% of the volume measured in CATIA reserved to take into account the structure and systems. The final fuel and total mass distributions are...for the calculations, such as the wing box height, the rib pitch, were obtained from CATIA . The laminate engineering properties were derived from

  12. Biofluiddynamic scaling of flapping, spinning and translating fins and wings

    NARCIS (Netherlands)

    Lentink, D.; Dickinson, M.H.

    2009-01-01

    Organisms that swim or fly with fins or wings physically interact with the surrounding water and air. The interactions are governed by the morphology and kinematics of the locomotory system that form boundary conditions to the Navier–Stokes (NS) equations. These equations represent Newton's law of m

  13. Unsteady aerodynamics of membrane wings with adaptive compliance

    Science.gov (United States)

    Kiser, Jillian; Breuer, Kenneth

    2016-11-01

    Membrane wings are known to provide superior aerodynamic performance at low Reynolds numbers (Re =104 -105), primarily due to passive shape adaptation to flow conditions. In addition to this passive deformation, active control of the fluid-structure interaction and resultant aerodynamic properties can be achieved through the use of dielectric elastomer actuators as the wing membrane material. When actuated, membrane pretension is decreased and wing camber increases. Additionally, actuation at resonance frequencies allows additional control over wing camber. We present results using synchronized (i) time-resolved particle image velocimetry (PIV) to resolve the flow field, (ii) 3D direct linear transformation (DLT) to recover membrane shape, (iii) lift/drag/torque measurements and (iv) near-wake hot wire anemometry measurements to characterize the fluid-structure interactions. Particular attention is paid to cases in which the vortex shedding frequency, the membrane resonance, and the actuation frequency coincide. In quantitatively examining both flow field and membrane shape at a range of actuation frequencies and vortex shedding frequencies, this work seeks to find actuation parameters that allow for active control of boundary layer separation over a range of flow conditions. Also at Naval Undersea Warfare Center, Division Newport.

  14. Biologically-Inspired Anisotropic Flexible Wing for Optimal Flapping Flight

    Science.gov (United States)

    2013-07-01

    Airfoils,” Experiments in Fluids, Vol. 46, (2009), pp. 883- 901. 16. Chimakurthi, S., Tang, J., Palacios , R., Cesnik, C., and Shyy, W., “Computational...Tang, J., Chimakurthi, S., Palacios , R., Cesnik, C.E.S. and Shyy, W., “Computational Fluid- Structure Interaction of a Deformable Flapping Wing for

  15. Flight mechanics of a tailless articulated wing aircraft

    Energy Technology Data Exchange (ETDEWEB)

    Paranjape, Aditya A; Chung, Soon-Jo; Selig, Michael S, E-mail: sjchung@illinois.edu [Department of Aerospace Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States)

    2011-06-15

    This paper investigates the flight mechanics of a micro aerial vehicle without a vertical tail in an effort to reverse-engineer the agility of avian flight. The key to stability and control of such a tailless aircraft lies in the ability to control the incidence angles and dihedral angles of both wings independently. The dihedral angles can be varied symmetrically on both wings to control aircraft speed independently of the angle of attack and flight path angle, while asymmetric dihedral can be used to control yaw in the absence of a vertical stabilizer. It is shown that wing dihedral angles alone can effectively regulate sideslip during rapid turns and generate a wide range of equilibrium turn rates while maintaining a constant flight speed and regulating sideslip. Numerical continuation and bifurcation analysis are used to compute trim states and assess their stability. This paper lays the foundation for design and stability analysis of a flapping wing aircraft that can switch rapidly from flapping to gliding flight for agile manoeuvring in a constrained environment.

  16. Wing coloration and pigment gradients in scales of pierid butterflies

    NARCIS (Netherlands)

    Giraldo, Marco A.; Stavenga, Doekele G.

    2008-01-01

    Depending on the species, the individual scales of butterfly wings have a longitudinal gradient in structure and reflectance properties, as shown by scanning electron microscopy and microspectrophotometry. White scales of the male Small White, Pieris rapae crucivora, show a strong gradient in both t

  17. Unique wing scale photonics of male Rajah Brooke's birdwing butterflies

    NARCIS (Netherlands)

    Wilts, Bodo D.; Giraldo, Marco A.; Stavenga, Doekele G.

    2016-01-01

    Background: Ultrastructures in butterfly wing scales can take many shapes, resulting in the often striking coloration of many butterflies due to interference of light. The plethora of coloration mechanisms is dazzling, but often only single mechanisms are described for specific animals. Results: We

  18. Interactive flutter analysis and parametric study for conceptual wing design

    Science.gov (United States)

    Mukhopadhyay, Vivek

    1995-01-01

    An interactive computer program was developed for wing flutter analysis in the conceptual design stage. The objective was to estimate the flutter instability boundary of a flexible cantilever wing, when well defined structural and aerodynamic data are not available, and then study the effect of change in Mach number, dynamic pressure, torsional frequency, sweep, mass ratio, aspect ratio, taper ratio, center of gravity, and pitch inertia, to guide the development of the concept. The software was developed on MathCad (trademark) platform for Macintosh, with integrated documentation, graphics, database and symbolic mathematics. The analysis method was based on nondimensional parametric plots of two primary flutter parameters, namely Regier number and Flutter number, with normalization factors based on torsional stiffness, sweep, mass ratio, aspect ratio, center of gravity location and pitch inertia radius of gyration. The plots were compiled in a Vaught Corporation report from a vast database of past experiments and wind tunnel tests. The computer program was utilized for flutter analysis of the outer wing of a Blended Wing Body concept, proposed by McDonnell Douglas Corporation. Using a set of assumed data, preliminary flutter boundary and flutter dynamic pressure variation with altitude, Mach number and torsional stiffness were determined.

  19. Investigation of engine jet/wing-tip vortex interference

    Energy Technology Data Exchange (ETDEWEB)

    Huppertz, G.; Fares, E.; Abstiens, R.; Schroder, W. [Aerodynamisches Institut, RWTH Aachen (Germany)

    2004-04-01

    The wing-tip vortex of a rectangular wing half-model with a model engine is studied experimentally and numerically. The airfoil has a supercritical BAC 3-11/RES/30/21 geometry with a chord length of c = 150 mm. The investigations include three different span-wise positions of the engine and two jet velocities with a constant free stream velocity of u{infinity}=27 m/s yielding Rec = 2.8 x 10{sup 5}. The numerical simulation is divided into two parts. First the flow around the airfoil is calculated. In a second step the data is taken as an input to calculate the wake downstream of the trailing edge. Experiments include 2C- and 3C-PIV-measurements for the velocity distribution of the jet and the wing-tip vortices. The experimental and numerical results show the significance of the stream-wise velocity component for the analysis of the jet/wing-tip vortex interaction. (author)

  20. Reactive Flow Control of Delta Wing Vortex (Postprint)

    Science.gov (United States)

    2006-08-01

    Passive vortex control devices such as vortex generators and winglets attach to the wing and require no energy input. Passive vortex control...width. The dynamic test parameters are summarized in Table 2. The composite duty cycle input signal is denoted ( ) ( )ou t u u tδ= + in which ou