WorldWideScience

Sample records for deflection spectroscopy pbds

  1. Application of photothermal deflection spectroscopy to electrochemical interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Rudnicki, J.D.; McLarnon, F.R.; Cairns, E.J.

    1992-03-01

    This dissertation discusses the theory and practice of Photothermal Deflection Spectroscopy (PDS, which is also known as probe beam deflection spectroscopy, PBDS, probe deflection technique, and mirage effect spectroscopy) with respect to electrochemical systems. Much of the discussion is also relevant to non-electrochemical systems. PDS can measure the optical absorption spectrum of interfaces and concentration gradients in the electrolyte adjacent to the electrode. These measurements can be made on a wide variety of electrode surfaces and can be performed under dynamic conditions. The first three chapters discuss the theory of the phenomena that can be detected by PDS, and the equipment used in a PDS system. A ``secondary gradient technique`` is proposed, which places the probe beam on the back of an electrode. The results of a numerical model yield a method for determining the offset of the probe beam from the electrode surface based on the frequency response of the PDS signal. The origin and control of noise in the PDS signal are discussed. A majority of the signal noise appears to be acoustic in origin. The electrochemical oxidation of platinum is used to demonstrate that PDS has sub-monolayer sensitivity necessary to study interfacial chemistry. The results allow us to propose a two-reaction oxidation mechanism: the platinum is electrochemically oxidized to form platinum dihydroxide and dehydrated by a non-electrochemical second-order reaction. The final chapter discusses the relation of PDS to similar and competing techniques, and considers possibilities for the future of the technique.

  2. Application of photothermal deflection spectroscopy to electrochemical interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Rudnicki, J.D.; McLarnon, F.R.; Cairns, E.J.

    1992-03-01

    This dissertation discusses the theory and practice of Photothermal Deflection Spectroscopy (PDS, which is also known as probe beam deflection spectroscopy, PBDS, probe deflection technique, and mirage effect spectroscopy) with respect to electrochemical systems. Much of the discussion is also relevant to non-electrochemical systems. PDS can measure the optical absorption spectrum of interfaces and concentration gradients in the electrolyte adjacent to the electrode. These measurements can be made on a wide variety of electrode surfaces and can be performed under dynamic conditions. The first three chapters discuss the theory of the phenomena that can be detected by PDS, and the equipment used in a PDS system. A secondary gradient technique'' is proposed, which places the probe beam on the back of an electrode. The results of a numerical model yield a method for determining the offset of the probe beam from the electrode surface based on the frequency response of the PDS signal. The origin and control of noise in the PDS signal are discussed. A majority of the signal noise appears to be acoustic in origin. The electrochemical oxidation of platinum is used to demonstrate that PDS has sub-monolayer sensitivity necessary to study interfacial chemistry. The results allow us to propose a two-reaction oxidation mechanism: the platinum is electrochemically oxidized to form platinum dihydroxide and dehydrated by a non-electrochemical second-order reaction. The final chapter discusses the relation of PDS to similar and competing techniques, and considers possibilities for the future of the technique.

  3. Sagnac interferometer for photothermal deflection spectroscopy.

    Science.gov (United States)

    Shiokawa, Naoyuki; Mizuno, Yuki; Tsuchiya, Harumasa; Tokunaga, Eiji

    2012-07-01

    Photothermal deflection spectroscopy is combined with a Sagnac interferometer to enhance the sensitivity of the absorption measurement by converting the photothermal beam deflection effect into the light intensity change by the interference effect. Because of stable light interference due to the common path, the signal intensity can be amplified without increasing the noise by extending the optical path length between a sample and a photodetector. The sensitivity is further improved by the use of focusing optics and double-pass geometry. This makes photothermal deflection spectroscopy applicable to any kind of material in the whole visible region with a xenon lamp for excitation and water or air as a deflection medium.

  4. Optimized frequency dependent photothermal beam deflection spectroscopy

    Science.gov (United States)

    Korte, D.; Cabrera, H.; Toro, J.; Grima, P.; Leal, C.; Villabona, A.; Franko, M.

    2016-12-01

    In the letter the optimization of the experimental setup for photothermal beam deflection spectroscopy is performed by analyzing the influence of its geometrical parameters (detector and sample position, probe beam radius and its waist position etc) on the detected signal. Furthermore, the effects of the fluid’s thermo-optical properties, for optimized geometrical configuration, on the measurement sensitivity and uncertainty determination of sample thermal properties is also studied. The examined sample is a recently developed CuFeInTe3 material. It is seen from the obtained results, that it is a complex problem to choose the proper geometrical configuration as well as sensing fluid to enhance the sensitivity of the method. A signal enhancement is observed at low modulation frequencies by placing the sample in acetonitrile (ACN), while at high modulation frequencies the sensitivity is higher for measurements made in air. For both, detection in air and acetonitrile the determination of CuFeInTe3 thermal properties is performed. The determined values of thermal diffusivity and thermal conductivity are (0.048  ±  0.002)  ×  10-4 m2 s-1 and 4.6  ±  0.2 W m-1 K-1 and (0.056  ±  0.005)  ×  10-4 m2 s-1 and 4.8  ±  0.4 W m-1 K-1 for ACN and air, respectively. It is seen, that the determined values agree well within the range of their measurement uncertainties for both cases, although the measurement uncertainty is two times lower for the measurements in ACN providing more accurate results. The analysis is performed by the use of recently developed theoretical description based on the complex geometrical optics. It is also shown, how the presented work fits into the current status of photothermal beam deflection spectroscopy.

  5. Quasi first-order Hermite Gaussian beam for enhanced sensitivity in Sagnac interferometer photothermal deflection spectroscopy.

    Science.gov (United States)

    Shiokawa, Naoyuki; Tokunaga, Eiji

    2016-05-30

    The detection sensitivity of a Sagnac interferometer photothermal deflection spectroscopy was enhanced by changing the probe beam pattern from zero-order to a quasi-first-order Hermite Gaussian (QHG) beam. The nature of the higher order HG mode, where the beam pattern is preserved during propagation with an increased field gradient, is utilized to enhance the measurement sensitivity. In this spectroscopy, the lateral beam deflection due to the photothermal effect is sensitively detected as a change in the interference light intensity. The change in intensity is amplified due to the higher field gradient of the QHG(1,0) beam at the photodetector. This amplification effect was both numerically and experimentally demonstrated to obtain twofold improvement in the signal-to-noise ratio.

  6. Pulsed-laser Pumped Photothermal Deflection Spectroscopy for Liquid Thermal Diffusivity Measurement

    Institute of Scientific and Technical Information of China (English)

    XIAO Liantuan; LI Changyong; ZHANG Linjie; ZHAO Yanting; JIA Suotang; ZHOU Guosheng

    2000-01-01

    The pulsed-laser pumped photothermal deflection spectroscopy (PPDS) is applied to measure liquid thermal diffusivity in a modified collinear configuration. Here the pulsed beam is regarded as in the form of a Dirac delta function. The experiment setup used is described. Measurement result for the thermal diffusivity of a liquid sample(magnta/ethanol saturated solution) is reported. The measurement error is less than 3%.

  7. Clustering mechanism of ethanol-water mixtures investigated with photothermal microfluidic cantilever deflection spectroscopy

    Science.gov (United States)

    Ghoraishi, M. S.; Hawk, J. E.; Phani, Arindam; Khan, M. F.; Thundat, T.

    2016-04-01

    The infrared-active (IR) vibrational mode of ethanol (EtOH) associated with the asymmetrical stretching of the C-C-O bond in pico-liter volumes of EtOH-water binary mixtures is calorimetrically measured using photothermal microfluidic cantilever deflection spectroscopy (PMCDS). IR absorption by the confined liquid results in wavelength dependent cantilever deflections, thus providing a complementary response to IR absorption revealing a complex dipole moment dependence on mixture concentration. Solvent-induced blue shifts of the C-C-O asymmetric vibrational stretch for both anti and gauche conformers of EtOH were precisely monitored for EtOH concentrations ranging from 20–100% w/w. Variations in IR absorption peak maxima show an inverse dependence on induced EtOH dipole moment (μ) and is attributed to the complex clustering mechanism of EtOH-water mixtures.

  8. Comparative Studies on Effects of Acid Solutions on Aquatic Plants by Beam Deflection and Absorbance Spectroscopy Methods.

    Science.gov (United States)

    Wu, Xing-Zheng; Nie, Liangjiao; Inoue, Tomomi

    2015-01-01

    The beam deflection method and absorbance spectroscopy were applied to study effects of acid solutions on aquatic plants, and their results were compared. Aquatic plants Egeria densa and Ceratophyllum demersum L were used as model plants. In absorbance experiments, a piece of the plants was put in a beaker with 20 mL HCl solution, and absorbance of the HCl solution was measured every 30 min. In beam deflection experiments, a probe beam from a He-Ne laser was focused to a vicinity of the plants in a culture dish with HCl solution by an objective lens, and deflection signals of the probe beam were monitored by a position sensor. Absorbance spectra of the HCl solutions with immersing of the plants showed absorbance below 410 nm, suggesting that some compounds leaked from the plants into the HCl solutions. Changes of absorbance and deflection signals with immersion time were examined for different pH levels. The changing trends of the absorbance and deflection signals with time were similar, but the absorbance changes were delayed for about 2 - 3 h. The absorbance method could not detect the effect of the pH 5.0 HCl solutions on the aquatic plants, while the deflection method could.

  9. Thermal characterization of Li-ion cell electrodes by photothermal deflection spectroscopy

    Science.gov (United States)

    Loges, André; Herberger, Sabrina; Werner, Daniel; Wetzel, Thomas

    2016-09-01

    Contactless and temperature-dependent evaluation of thermal diffusivities of Li-ion cell electrodes based on photothermal deflection spectroscopy (PDS) measurements is introduced and applied to electrodes from three prismatic hardcase Li-ion cells. The accuracy of the method is validated using reference materials, which cover a wide range of thermal diffusivity. The effective thermal diffusivities of the three anode and cathode coatings and of the current collectors are determined in the temperature range of 5-45 °C. Furthermore, the temperature-dependent specific heat capacity of the electrodes is evaluated by differential scanning calorimetry (DSC) measurements in the same temperature range. Based on the experimental results the through-plane and in-plane thermal conductivity of the electrodes is calculated and compared to previously reported values. The results indicate significant influence of the porosity and manufacturing process on the effective thermal conductivity of the electrodes. The three mayor impact factors on thermal conductivity of electrodes are (i) composition, (ii) morphology of the coating and (iii) the thickness ratio of coating to current collector.

  10. Monitoring electrostatically-induced deflection, strain and doping in suspended graphene using Raman spectroscopy

    Science.gov (United States)

    Metten, Dominik; Froehlicher, Guillaume; Berciaud, Stéphane

    2017-03-01

    Electrostatic gating offers elegant ways to simultaneously strain and dope atomically thin membranes. Here, we report on a detailed in situ Raman scattering study on graphene, suspended over a Si/SiO2 substrate. In such a layered structure, the intensity of the Raman G- and 2D-mode features of graphene are strongly modulated by optical interference effects and allow an accurate determination of the electrostatically-induced membrane deflection, up to irreversible collapse. The membrane deflection is successfully described by an electromechanical model, which we also use to provide useful guidelines for device engineering. In addition, electrostatically-induced tensile strain is determined by examining the softening of the Raman features. Due to a small residual charge inhomogeneity, we find that non-adiabatic anomalous phonon softening is negligible compared to strain-induced phonon softening. These results open perspectives for innovative Raman scattering-based readout schemes in two-dimensional nanoresonators.

  11. In-situ stress analysis of the Zr/ZrO2 system as studied by Raman spectroscopy and deflection test in monofacial oxidation techniques

    Science.gov (United States)

    Kurpaska, L.; Favergeon, J.; Grosseau-Poussard, J.-L.; Lahoche, L.; Moulin, G.

    2016-11-01

    A comparison of measurements performed in in-situ conditions using Raman spectroscopy and Deflection Test in Monofacial Oxidation techniques were employed to study stress states developed in zirconia films grown at 500 °C is presented. The results show a good correlation between recorded Raman peak displacement and sample deflection angle. Considering analyzed volume of the material, Raman analysis represents a local measurement while the deflection test is a global response of the material. Reported stress components: (i) hydrostatic - resulted from Raman spectroscopy and (ii) in-plane - resulted from deflection test technique have been analyzed in comparison to each of the described techniques and aim to explain the behavior of zirconia at high temperatures.

  12. Direct correlation of charge transfer absorption with molecular donor:acceptor interfacial area via photothermal deflection spectroscopy

    KAUST Repository

    Domingo, Ester

    2015-04-09

    We show that the Charge Transfer (CT) absorption signal in bulk-heterojunction (BHJ) solar cell blends, measured by photothermal deflection spectroscopy (PDS), is directly proportional to the density of molecular donor/acceptor interfaces. Since the optical transitions from ground state to the interfacial CT state are weakly allowed at photon energies below the optical gap of both donor and acceptor, we can exploit the use of this sensitive linear absorption spectroscopy for such quantification. Moreover, we determine the absolute molar extinction coefficient of the CT transition for an archetypical polymer-fullerene interface. The latter is ~100 times lower than the extinction coefficient of the donor chromophore involved, allowing us to experimentally estimate the transition dipole moment (0.3 D) and the electronic coupling between ground state and CT state to be on the order of 30 meV.

  13. Bandedge optical properties of MBE grown GaAsBi films measured by photoluminescence and photothermal deflection spectroscopy

    Science.gov (United States)

    Beaudoin, M.; Lewis, R. B.; Andrews, J. J.; Bahrami-Yekta, V.; Masnadi-Shirazi, M.; O'Leary, S. K.; Tiedje, T.

    2015-09-01

    The bandedge optical properties of GaAsBi films, as thick as 470 nm, with Bi content varying from 0.7% Bi to 2.8% Bi grown by molecular beam epitaxy on GaAs substrates are measured by photoluminescence (PL) and photothermal deflection spectroscopy (PDS). The PDS spectra were fit with a modified Fernelius model which takes into account multiple reflections within the GaAsBi layer and GaAs substrate. Three undoped samples and two samples that are degenerately doped with silicon are studied. The undoped samples show a clear Urbach absorption edge with a composition dependent bandgap that decreases by 56 meV/% Bi and a composition independent Urbach slope parameter of 25 meV due to absorption by Bi cluster states near the valence band. The doped samples show a long absorption tail possibly due to absorption by gap states and free carriers in addition to a Burstein-Moss bandgap shift. PL of the undoped samples shows a lower energy emission peak due to defects not observed in the usually available thin samples (50 nm or less) grown under similar conditions.

  14. Time-of-flight electron energy loss spectroscopy using TM110 deflection cavities

    Directory of Open Access Journals (Sweden)

    W. Verhoeven

    2016-09-01

    Full Text Available We demonstrate the use of two TM110 resonant cavities to generate ultrashort electron pulses and subsequently measure electron energy losses in a time-of-flight type of setup. The method utilizes two synchronized microwave cavities separated by a drift space of 1.45 m. The setup has an energy resolution of 12 ± 2 eV FWHM at 30 keV, with an upper limit for the temporal resolution of 2.7 ± 0.4 ps. Both the time and energy resolution are currently limited by the brightness of the tungsten filament electron gun used. Through simulations, it is shown that an energy resolution of 0.95 eV and a temporal resolution of 110 fs can be achieved using an electron gun with a higher brightness. With this, a new method is provided for time-resolved electron spectroscopy without the need for elaborate laser setups or expensive magnetic spectrometers.

  15. Time-of-flight electron energy loss spectroscopy using TM110 deflection cavities.

    Science.gov (United States)

    Verhoeven, W; van Rens, J F M; van Ninhuijs, M A W; Toonen, W F; Kieft, E R; Mutsaers, P H A; Luiten, O J

    2016-09-01

    We demonstrate the use of two TM110 resonant cavities to generate ultrashort electron pulses and subsequently measure electron energy losses in a time-of-flight type of setup. The method utilizes two synchronized microwave cavities separated by a drift space of 1.45 m. The setup has an energy resolution of 12 ± 2 eV FWHM at 30 keV, with an upper limit for the temporal resolution of 2.7 ± 0.4 ps. Both the time and energy resolution are currently limited by the brightness of the tungsten filament electron gun used. Through simulations, it is shown that an energy resolution of 0.95 eV and a temporal resolution of 110 fs can be achieved using an electron gun with a higher brightness. With this, a new method is provided for time-resolved electron spectroscopy without the need for elaborate laser setups or expensive magnetic spectrometers.

  16. Time-of-flight electron energy loss spectroscopy using TM110 deflection cavities

    Science.gov (United States)

    Verhoeven, W.; van Rens, J. F. M.; van Ninhuijs, M. A. W.; Toonen, W. F.; Kieft, E. R.; Mutsaers, P. H. A.; Luiten, O. J.

    2016-01-01

    We demonstrate the use of two TM110 resonant cavities to generate ultrashort electron pulses and subsequently measure electron energy losses in a time-of-flight type of setup. The method utilizes two synchronized microwave cavities separated by a drift space of 1.45 m. The setup has an energy resolution of 12 ± 2 eV FWHM at 30 keV, with an upper limit for the temporal resolution of 2.7 ± 0.4 ps. Both the time and energy resolution are currently limited by the brightness of the tungsten filament electron gun used. Through simulations, it is shown that an energy resolution of 0.95 eV and a temporal resolution of 110 fs can be achieved using an electron gun with a higher brightness. With this, a new method is provided for time-resolved electron spectroscopy without the need for elaborate laser setups or expensive magnetic spectrometers. PMID:27704035

  17. Photothermal deflection spectroscopy for the study of thin films and optical coatings: measurements of absorption losses and detection of photoinduced changes

    Science.gov (United States)

    Commandre, Mireille; Roche, Pierre J.; Albrand, Gerard; Pelletier, Emile P.

    1990-08-01

    Photothermal deflection has been used to map the absorption characteristics of thin film optical coatings. Our experimental set-up can give low level absorption coefficient down to 1 ppm, with a spatial resolution limited by the excitating laser beam diameter (100 tim). On single layer films, we can calculate extinction coefficient of the deposited material with a detectivity of a few i07. We present a study of absorption losses in single layer titania films and in TiOWSiO2 Fabry-Perot filters prepared in our laboratory by electron beam evaporation, ion assisted deposition and ion plating. Local variations of absorption on the sample surface can be very large especially in lowly absorbing samples; high absorption sites may be related to local defects responsible for laser damage. Furthermore, we show that some titania films can present photoinduced instabilities. Photothermal deflection spectroscopy is a good way to study absorption evolution under illumination. In Ti02/Si02 Fabry-Perot filters, we have observed that these absorption changes are associated with important drifts of transmission curves. So these instabilities can be explained by a change of the value of the complex index Ii = n - ik. Results lead to the conclusion that stability under illumination is strongly correlated to the deposition technique and also to the deposition conditions: unstable samples are mostly prepared by electron beam evaporation.

  18. The Deflection Question

    Science.gov (United States)

    Greenberg, A. H.; Nesvold, E.; van Heerden, E.; Erasmus, N.; Marchis, F.

    2016-12-01

    On 15 February, 2013, a 15 m diameter asteroid entered the Earth's atmosphere over Russia. The resulting shockwave injured nearly 1500 people, and incurred 33 million (USD) in infrastructure damages. The Chelyabinsk meteor served as a forceful demonstration of the threat posed to Earth by the hundreds of potentially hazardous objects (PHOs) that pass near the Earth every year. Although no objects have yet been discovered on an impact course for Earth, an impact is virtually statistically guaranteed at some point in the future. While many impactor deflection technologies have been proposed, humanity has yet to demonstrate the ability to divert an impactor when one is found. Developing and testing any single proposed technology will require significant research time and funding. This leaves open an obvious question - towards which technologies should funding and research be directed, in order to maximize our preparedness for when an impactor is eventually found? To help answer this question, we have created a detailed framework for analyzing various deflection technologies and their effectiveness. Using an n-body integrator (REBOUND), we have simulated the attempted deflections of a population of Earth-impacting objects with a variety of velocity perturbations (∂Vs), and measured the effects that these perturbations had on impact probability. We then mapped the ∂Vs applied in the orbital simulations to the technologies capable of achieving those perturbations, and analyzed which set of technologies would be most effective at preventing a PHO from impacting the earth. As a final step, we used the results of these simulations to train a machine learning algorithm. This algorithm, combined with a simulated PHO population, can predict which technologies are most likely to be needed. The algorithm can also reveal which impactor observables (mass, spin, orbit, etc.) have the greatest effect on the choice of deflection technology. These results can be used as a tool to

  19. Experiments on Deflecting & Oscillating Waterjet

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A new type jet,the oscillating & deflecting jet ,is put forward and its oscillating and deflecting characteristics are investigated.The nozzle of the self-oscillating & deflecting water jet consists of an upstream nozzle,a downstream nozzle,an oscillating chamber and two switches,It is experimentally shown that the deflective angle may reach 9.53 degeree,the generated pressure fluctuation is very regular and the jet can efficiently increase the ability for bradking and cutting by eliminating the water cushion effect associated with a continuous jet.

  20. Electric Deflection of Rotating Molecules

    CERN Document Server

    Gershnabel, E

    2010-01-01

    We provide a theory of the deflection of polar and non-polar rotating molecules by inhomogeneous static electric field. Rainbow-like features in the angular distribution of the scattered molecules are analyzed in detail. Furthermore, we demonstrate that one may efficiently control the deflection process with the help of short and strong femtosecond laser pulses. In particular the deflection process may by turned-off by a proper excitation, and the angular dispersion of the deflected molecules can be substantially reduced. We study the problem both classically and quantum mechanically, taking into account the effects of strong deflecting field on the molecular rotations. In both treatments we arrive at the same conclusions. The suggested control scheme paves the way for many applications involving molecular focusing, guiding, and trapping by inhomogeneous fields.

  1. Photothermal deflection spectroscopy as characterisation method for thin film solar cells on the basis of amorphous silicon; Photothermische Deflexions-Spektroskopie als Charakterisierungsmethode fuer Duennschichtsolarzellen auf der Basis von amorphem Silizium

    Energy Technology Data Exchange (ETDEWEB)

    Hoehne, N.

    1997-09-01

    The potential of photothermal deflection spectroscopy (PDS) as a method to characterise solar cells based on amorphous silicon was studied in this thesis. It was demonstrated, how the proportions of the loss mechanisms of a solar cell under operating conditions can be obtained from PDS measurements as a function of the wavelength of the incident light. In addition, significant movement of heat sources in the layer system of the solar cell, such as the transition from absorption in the layers to absorption in the glass substrate can be detected using the phase of the PDS signal. However, detection of a change of the heat source distribution within the deposited layers of the solar cell was restricted by insufficient experimental resolution of the method. In particular, for the comparison with the experimental results, the dynamic heat transport within a layer system was simulated starting from a given heat source distribution and the expected amplitude and phase of the PDS signal was calculated. Experimental conditions were established to reach a high signal stability (1% in amplitude, 0.1 in phase) in order to resolve small phase shifts. Calibration experiments and theoretical calculations predict a phase shift of 0.35{+-}0.15 , if the heats source moves 0.4 {mu}m within the i-layer of a-Si:H PIN solar cell. However, phase shifts as a result of changes in the applied voltages, which are expected to be even smaller, could not be resolved experimentally. From PDS spectra at different voltages, the proportions of the loss mechanisms as a function of the wavelength were derived. 22 refs.

  2. Combustion Diagnostics by Photo-Deflection Spectroscopy

    Science.gov (United States)

    1992-03-01

    temperature in a sooting Ilame heavily sooting flame . Nevertheless it is an inter- by geinerating tile acoustic signal on soot particles. esting idea that...mea- ly investigated. In the present work, we have only surements in a sooting flame by simply scattering laser measured the relative temperatures

  3. Benchmarking Asteroid-Deflection Experiment

    Science.gov (United States)

    Remington, Tane; Bruck Syal, Megan; Owen, John Michael; Miller, Paul L.

    2016-10-01

    An asteroid impacting Earth could have devastating consequences. In preparation to deflect or disrupt one before it reaches Earth, it is imperative to have modeling capabilities that adequately simulate the deflection actions. Code validation is key to ensuring full confidence in simulation results used in an asteroid-mitigation plan. We are benchmarking well-known impact experiments using Spheral, an adaptive smoothed-particle hydrodynamics code, to validate our modeling of asteroid deflection. We describe our simulation results, compare them with experimental data, and discuss what we have learned from our work. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344. LLNL-ABS-695540

  4. Geometric formula for prism deflection

    Indian Academy of Sciences (India)

    Apoorva G Wagh; Veer Chand Rakhecha

    2004-08-01

    While studying neutron deflections produced by a magnetic prism, we have stumbled upon a simple `geometric' formula. For a prism of refractive index close to unity, the deflection simply equals the product of the refractive power − 1 and the base-to-height ratio of the prism, regardless of the apex angle. The base and height of the prism are measured respectively along and perpendicular to the direction of beam propagation within the prism. The geometric formula greatly simplifies the optimisation of prism parameters to suit any specific experiment.

  5. Relativistic Stern-Gerlach Deflection

    CERN Document Server

    Talman, Richard

    2016-01-01

    Modern advances in polarized beam control should make it possible to accurately measure Stern-Gerlach (S-G) deflection of relativistic beams. Toward this end a relativistically covariant S-G formalism is developed that respects the opposite behavior under inversion of electric and magnetic fields. Not at all radical, or even new, this introduces a distinction between electric and magnetic fields that is not otherwise present in pure Maxwell theory. Experimental configurations (mainly using polarized electron beams passing through magnetic or electric quadrupoles) are described. Electron beam preparation and experimental methods needed to detect the extremely small deflections are discussed.

  6. AIDA: Asteroid Impact & Deflection Assessment

    Science.gov (United States)

    Cheng, A. F.; Galvez, A.; Carnelli, I.; Michel, P.; Rivkin, A.; Reed, C.

    2012-12-01

    To protect the Earth from a hazardous asteroid impact, various mitigation methods have been proposed, including deflection of the asteroid by a spacecraft impact. AIDA, consisting of two mission elements, the Double Asteroid Redirection Test (DART) and the Asteroid Impact Monitoring (AIM) mission, is a demonstration of asteroid deflection. To date, there has been no such demonstration, and there is major uncertainty in the result of a spacecraft impact onto an asteroid, that is, the amount of deflection produced by a given momentum input from the impact. This uncertainty is in part due to unknown physical properties of the asteroid surface, such as porosity and strength, and in part due to poorly understood impact physics such that the momentum carried off by ejecta is highly uncertain. A first mission to demonstrate asteroid deflection would not only be a major step towards gaining the capability to mitigate an asteroid hazard, but in addition it would return unique information on an asteroid's strength, other surface properties, and internal structure. This information return would be highly relevant to future human exploration of asteroids. We report initial results of the AIDA joint mission concept study undertaken by the Johns Hopkins Applied Physics Laboratory and ESA with support from NASA centers including Goddard, Johnson and Jet Propulsion Laboratory. For AIDA, the DART spacecraft impactor study is coordinated with an ESA study of the AIM mission, which would rendezvous with the same asteroid to measure effects of the impact. Unlike the previous Don Quijote mission study performed by ESA in 2005-2007, DART envisions an impactor spacecraft to intercept the secondary member of a binary near-Earth asteroid. DART includes ground-based observations to measure the deflection independently of the rendezvous spacecraft observations from AIM, which also measures deflection and provides detailed characterization of the target asteroid. The joint mission AIDA

  7. Elevator deflections on the icing process

    Science.gov (United States)

    Britton, Randall K.

    1990-01-01

    The effect of elevator deflection of the horizontal stabilizer for certain icing parameters is investigated. Elevator deflection can severely change the lower and upper leading-edge impingement limits, and ice can accrete on the elevator itself. Also, elevator deflection had practically no effect on the maximum local collection efficiency. It is shown that for severe icing conditions (large water droplets), elevator deflections that increase the projected height of the airfoil can significantly increase the total collection efficiency of the airfoil.

  8. Field distribution analysis in deflecting structures

    Energy Technology Data Exchange (ETDEWEB)

    Paramonov, V.V. [Joint Inst. for Nuclear Research, Moscow (Russian Federation)

    2013-02-15

    Deflecting structures are used now manly for bunch rotation in emittance exchange concepts, bunch diagnostics and to increase the luminosity. The bunch rotation is a transformation of a particles distribution in the six dimensional phase space. Together with the expected transformations, deflecting structures introduce distortions due to particularities - aberrations - in the deflecting field distribution. The distributions of deflecting fields are considered with respect to non linear additions, which provide emittance deteriorations during a transformation. The deflecting field is treated as combination of hybrid waves HE{sub 1} and HM{sub 1}. The criteria for selection and formation of deflecting structures with minimized level of aberrations are formulated and applied to known structures. Results of the study are confirmed by comparison with results of numerical simulations.

  9. Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Hellman, Hal

    1968-01-01

    This booklet discusses spectroscopy, the study of absorption of radiation by matter, including X-ray, gamma-ray, microwave, mass spectroscopy, as well as others. Spectroscopy has produced more fundamental information to the study of the detailed structure of matter than any other tools.

  10. Spectroscopy

    CERN Document Server

    Walker, S

    1976-01-01

    The three volumes of Spectroscopy constitute the one comprehensive text available on the principles, practice and applications of spectroscopy. By giving full accounts of those spectroscopic techniques only recently introduced into student courses - such as Mössbauer spectroscopy and photoelectron spectroscopy - in addition to those techniques long recognised as being essential in chemistry teaching - sucha as e.s.r. and infrared spectroscopy - the book caters for the complete requirements of undergraduate students and at the same time provides a sound introduction to special topics for graduate students.

  11. Deflection Control in Rigid Pavements

    Science.gov (United States)

    Varunkrishna, Nulu; Jayasankar, R.

    2017-07-01

    The need for modern transportation systems together with the high demand for perpetual pavements under the drastically increasing applied loads has led to a great deal of research on concrete as a pavement material worldwide. This research indeed instigated many modifications in concrete aiming for improving the concrete properties. Pavement Quality Concrete requires higher flexural strength and fewer deflections in hardened state. Fiber reinforcement and latex modification are two reliable approaches serving the required purposes. The concrete made with these two modifications is called Polymer-modified Fiber-reinforced concrete. The present study deals with the usage of polypropylene as fiber and SBR (Styrene Butadiene Rubber) Latex as polymer. M30 grade concrete was modified by replacing cement with two different percentages of fiber (0.5%, 1.0% of weight of cement) and with three different percentages of SBR latex (10%, 15% & 20% of weight of cement).

  12. Directed energy deflection laboratory measurements

    Science.gov (United States)

    Brashears, Travis; Lubin, Phillip; Hughes, Gary B.; Meinhold, Peter; Suen, Jonathan; Batliner, Payton; Motta, Caio; Griswold, Janelle; Kangas, Miikka; Johansson, Isbella; Alnawakhtha, Yusuf; Prater, Kenyon; Lang, Alex; Madajian, Jonathan

    2015-09-01

    We report on laboratory studies of the effectiveness of directed energy planetary defense as a part of the DESTAR (Directed Energy System for Targeting of Asteroids and exploRation) program. DE-STAR [1][5][6] and DE-STARLITE [2][5][6] are directed energy "stand-off" and "stand-on" programs, respectively. These systems consist of a modular array of kilowatt-class lasers powered by photovoltaics, and are capable of heating a spot on the surface of an asteroid to the point of vaporization. Mass ejection, as a plume of evaporated material, creates a reactionary thrust capable of diverting the asteroid's orbit. In a series of papers, we have developed a theoretical basis and described numerical simulations for determining the thrust produced by material evaporating from the surface of an asteroid [1][2][3][4][5][6]. In the DE-STAR concept, the asteroid itself is used as the deflection "propellant". This study presents results of experiments designed to measure the thrust created by evaporation from a laser directed energy spot. We constructed a vacuum chamber to simulate space conditions, and installed a torsion balance that holds an "asteroid" sample. The sample is illuminated with a fiber array laser with flux levels up to 60 MW/m2 which allows us to simulate a mission level flux but on a small scale. We use a separate laser as well as a position sensitive centroid detector to readout the angular motion of the torsion balance and can thus determine the thrust. We compare the measured thrust to the models. Our theoretical models indicate a coupling coefficient well in excess of 100 μN/Woptical, though we assume a more conservative value of 80 μN/Woptical and then degrade this with an optical "encircled energy" efficiency of 0.75 to 60 μN/Woptical in our deflection modeling. Our measurements discussed here yield about 45 μN/Wabsorbed as a reasonable lower limit to the thrust per optical watt absorbed.

  13. Large Deflections of Elastic Rectangular Plates

    Science.gov (United States)

    Razdolsky, A. G.

    2015-11-01

    It is known that elastic large deflections of thin plates are governed by von Karman nonlinear equations. The analytical solution of these equations in the general case is unfeasible. Samuel Levy, in 1942, showed that large deflections of the rectangular plate can be expressed as a double series of sine-shaped harmonics (deflection harmonics). However, this method gave no way of creating the computer algorithm of solving the problem. The stress function expression taken in the Levy's method must be revised to find the approach that takes into account of all possible products of deflection coefficients. The algorithm of solving the problem for the rectangular plate with an arbitrary aspect ratio under the action of the lateral distributed load is reported in this paper. The approximation of the plate deflection is taken in the form of double series proposed by Samuel Levy. However, the expression for the stress function is presented in the form that incorporates products of deflection coefficients in the explicit form in distinction to the Levy's expression. The number of harmonics in the deflection expression may be arbitrary. The algorithm provides composing the system of governing cubic equations, which includes the deflection coefficients in the explicit form. Solving the equation system is based on using the principle of minimum potential energy. A method of the gradient descent is applied to find the equilibrium state of the plate as the minimum point of the potential energy. A computer program is developed on the basis of the present algorithm. Numerical examples carried out for the plate model with 16 deflection harmonics illustrate the potentialities of the program. The results of solving the examples are presented in the graphical form for the plates with a different aspect ratio and may be used under designing thin-walled elements of airplane and ship structures.

  14. Ion Beam Shepherd for Asteroid Deflection

    CERN Document Server

    Bombardelli, C

    2011-01-01

    We present a novel concept to impart a continuous thrust to an Earth threatening asteroid from a hovering spacecraft without need for physical attachment nor gravitational interaction with the asteroid. The concept involves an ion thruster placed at a distance of a few asteroid diameters directing a stream of quasi-neutral plasma against the asteroid surface resulting into a net transferred momentum. As the transmitted force is independent of the asteroid mass and size the method allows deflecting subkilometer asteroids with a spacecraft much lighter when compared to a gravity tractor spacecraft of equal deflection capability. The finding could make low-cost asteroid deflection missions possible in the coming years.

  15. Spectroscopy

    DEFF Research Database (Denmark)

    Berg, Rolf W.

    This introductory booklet covers the basics of molecular spectroscopy, infrared and Raman methods, instrumental considerations, symmetry analysis of molecules, group theory and selection rules, as well as assignments of fundamental vibrational modes in molecules.......This introductory booklet covers the basics of molecular spectroscopy, infrared and Raman methods, instrumental considerations, symmetry analysis of molecules, group theory and selection rules, as well as assignments of fundamental vibrational modes in molecules....

  16. Alaska North-South Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' x 4' surface deflection of the vertical grid for Alaska is the DEFLEC96 model. The computation used about 1.1 million terrestrial and marine gravity data...

  17. Mexico East-West Deflections (DMEX97)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for Mexico, and North-Central is the DMEX97 model. The computation used about one million terrestrial and marine...

  18. Alaska East-West Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' x 4' surface deflection of the vertical grid for Alaska is the DEFLEC96 model. The computation used about 1.1 millionterrestrial and marine gravity data held...

  19. Mexico North-South Deflections (DMEX97)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for Mexico, and North-Central is the DMEX97 model. The computation used about one million terrestrial and marine...

  20. Finite element analysis modeling of pulse-laser excited photothermal deflection (mirage effect) from aerosols.

    Science.gov (United States)

    Dada, Oluwatosin O; Bialkowski, Stephen E

    2008-12-01

    A finite element analysis method for numerical modeling of the photothermal deflection spectroscopy of aerosols is presented. The models simulate pulse-laser excited photothermal deflection from aerosols collected on a plane surface substrate in air medium. The influence of the aerosol and substrate properties on the transient photothermal deflection signal is examined. We have previously obtained experimental results for photothermal deflection spectrometry of aerosols deposited onto a plate from an impactor system (O. O. Dada and S. E. Bialkowski, Appl. Spectrosc. 62, 1336 (2008)). This paper supports the validity of the experimental results presented in that paper and helps in answering some of the questions raised. The modeling results presented here demonstrate that the (peak) normalized transient temperature change profile and (peak) normalized transient photothermal deflection profile are a good approximation and invariant with number of particles, inter-particle distance, and particulate shape, which suggests that the photothermal deflection signal amplitude may be calibrated linearly with total mass of aerosols and the method could be applied to analysis of complex aerosols.

  1. Base deflection and microleakage of composite restorations.

    Science.gov (United States)

    Paulillo, L A; de Goes, M F; Consani, S

    1994-06-01

    The flexural deflections of human dentin, Herculite XR, Dycal, Vidrion F, zinc phosphate base, and combinations of composite-base were determined. The influence of the flexural deflections in the marginal microleakage was also determined for the composite-base combinations. The flexural deflection test for dentin showed no statistically significant differences between the two floor cavity depths studied. There were significant differences among cements when the thickness of the base was 1 mm whereas no differences occurred at 2 mm. The composite-base combinations did not present statistical differences. There were no statistically significant differences in the microleakage levels among loaded and non-loaded specimens; however, dye penetration was visually greater in loaded samples.

  2. Small angle electron diffraction and deflection

    Directory of Open Access Journals (Sweden)

    T. Koyama

    2012-03-01

    Full Text Available Electron optical system is constructed in order to obtain small angle diffraction and Lorentz deflection of electrons at the order of down to 10-6 radian in the reciprocal space. Long-distance camera length up to 3000 m is achieved in a conventional transmission electron microscope with LaB6 thermal emission type. The diffraction pattern at 5 × 10-6 radian is presented in a carbon replica grating with 500 nm lattice spacing while the magnetic deflection pattern at 2 × 10-5 radian is exhibited in Permalloy elements. A simultaneous recording of electron diffraction and Lorentz deflection is also demonstrated in 180 degree striped magnetic domains of La0.825Sr0.175MnO3.

  3. Laboratory experiments on arc deflection and instability

    Energy Technology Data Exchange (ETDEWEB)

    Zweben, S.; Karasik, M.

    2000-03-21

    This article describes experiments on arc deflection instability carried out during the past few years at the Princeton University Plasma Physics Laboratory (PPPL). The approach has been that of plasma physicists interested in arcs, but they believe these results may be useful to engineers who are responsible for controlling arc behavior in large electric steel furnaces.

  4. Impeller deflection and modal finite element analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, Nathan A.

    2013-10-01

    Deflections of an impeller due to centripetal forces are calculated using finite element analysis. The lateral, or out of plane, deflections are an important design consideration for this particular impeller because it incorporates an air bearing with critical gap tolerances. The target gap distance is approximately 10 microns at a rotational velocity of 2500 rpm. The centripetal forces acting on the impeller cause it deflect in a concave fashion, decreasing the initial gap distance as a function of radial position. This deflection is characterized for a previous and updated impeller design for comparative purposes. The impact of design options such as material selection, geometry dimensions, and operating rotational velocity are also explored, followed by a sensitivity study with these parameters bounded by specific design values. A modal analysis is also performed to calculate the impeller's natural frequencies which are desired to be avoided during operation. The finite element modeling techniques continue to be exercised by the impeller design team to address specific questions and evaluate conceptual designs, some of which are included in the Appendix.

  5. Deflection of uncooperative targets using laser ablation

    Science.gov (United States)

    Thiry, Nicolas; Vasile, Massimiliano

    2015-09-01

    Owing to their ability to move a target in space without requiring propellant, laser-based deflection methods have gained attention among the research community in the recent years. With laser ablation, the vaporized material is used to push the target itself allowing for a significant reduction in the mass requirement for a space mission. Specifically, this paper addresses two important issues which are thought to limit seriously the potential efficiency of a laser-deflection method: the impact of the tumbling motion of the target as well as the impact of the finite thickness of the material ablated in the case of a space debris. In this paper, we developed a steady-state analytical model based on energetic considerations in order to predict the efficiency range theoretically allowed by a laser deflection system in absence of the two aforementioned issues. A numerical model was then implemented to solve the transient heat equation in presence of vaporization and melting and account for the tumbling rate of the target. This model was also translated to the case where the target is a space debris by considering material properties of an aluminium 6061-T6 alloy and adapting at every time-step the size of the computational domain along with the recession speed of the interface in order to account for the finite thickness of the debris component. The comparison between the numerical results and the analytical predictions allow us to draw interesting conclusions regarding the momentum coupling achievable by a given laser deflection system both for asteroids and space debris in function of the flux, the rotation rate of the target and its material properties. In the last section of this paper, we show how a reasonably small spacecraft could deflect a 56m asteroid with a laser system requiring less than 5kW of input power.

  6. Dark matter prospects in deflected mirage mediation

    Energy Technology Data Exchange (ETDEWEB)

    Holmes, Michael; Nelson, Brent D., E-mail: holmes.mi@neu.edu, E-mail: b.nelson@neu.edu [Department of Physics, Northeastern University, Boston, MA 02115 (United States)

    2009-07-01

    The recently introduced deflected mirage mediation (DMM) model is a string-motivated paradigm in which all three of the major supersymmetry-breaking transmission mechanisms are operative. We begin a systematic exploration of the parameter space of this rich model context, paying special attention to the pattern of gaugino masses which arise. In this work we focus on the dark matter phenomenology of the DMM model as such signals are the least influenced by the model-dependent scalar masses. We find that a large portion of the parameter space in which the three mediation mechanisms have a similar effective mass scale of 1 TeV or less will be probed by future direct and indirect detection experiments. Distinguishing deflected mirage mediation from the mirage model without gauge mediation will prove difficult without collider input, though we indicate how gamma ray signals may provide an opportunity for distinguishing between the two paradigms.

  7. Surface effects on large deflection of nanowires

    Institute of Scientific and Technical Information of China (English)

    杨帆

    2015-01-01

    Surface effects play an important role in the mechanical behavior of nanosized structural elements owing to the increased ratio of surface area to volume. The surface effects on the large deflection of nanowires were considered. Both geometric nonlinearity in finite deformation and surface effects at nanoscale were taken into account to analyze the bending of nanowires subjected to a concentrated force. For simply supported beams and clamped-clamped beams, the influence of surface effects and geometric nonlinearity were discussed in detail. It is found that both surface effects and geometric nonlinearity tend to decrease the deflection of bending nanowires and thus increase the effective elastic modulus of nanowires. Surface effects yield the size dependent behavior of nanowires.

  8. Optical forces through guided light deflections

    DEFF Research Database (Denmark)

    Palima, Darwin; Bañas, Andrew Rafael; Vizsnyiczai, Gaszton;

    2013-01-01

    Optical trapping and manipulation typically relies on shaping focused light to control the optical force, usually on spherical objects. However, one can also shape the object to control the light deflection arising from the light-matter interaction and, hence, achieve desired optomechanical effects....... In this work we look into the object shaping aspect and its potential for controlled optical manipulation. Using a simple bent waveguide as example, our numerical simulations show that the guided deflection of light efficiently converts incident light momentum into optical force with one order...... show that the force on the waveguide exceeds the combined forces on spherical trapping handles. Furthermore, it shows that static illumination can exert a constant force on a moving structure, unlike the position-dependent forces from harmonic potentials in conventional trapping....

  9. Deflection analysis of rectangular spatial coverage truss

    Directory of Open Access Journals (Sweden)

    M.N. Kirsanov

    2015-02-01

    Full Text Available An elastic spatial statically determinate truss of regular type, simulating the rectangular in plan coverage was considered. In the plane of the base the truss has two axes of symmetry. Four support structures (spherical hinge, cylindrical hinge and two vertical rods are located at its corners. An analytic solution was found for forces in the rods of the truss. Using the Maxwell-Mohr’s formula, the dependence of the deflection of the center was discovered in the truss under the influence of the concentrated force. There are five parameters of the problem in this formula: three linear dimensions, and the numbers of hinges on its lateral sides. To determine the desired patterns by means of the computer mathematics system Maple the recursion task by two parameters was solved. It was shown that dependence of the deflection on the number of panels and height of the truss detects a minimum, allowing optimizing the size of the structure.

  10. Deflection of proton beams by crystal miscut surface

    CERN Document Server

    Babaev, A A; Dabagov, S B

    2014-01-01

    First computer experiment results on proton beam deflection by the crystal miscut surface are presented. The phenomenology of proton channeling and quasichanneling has been applied to describe new features of the beam deflection. The analysis predicts efficient beam deflection by the acute crystal end due to repelling miscut potential.

  11. Deflection rheoevolution of lithosphere under subduction

    Institute of Scientific and Technical Information of China (English)

    韩玉英; 王维襄

    1997-01-01

    Along the continental margin, the tectonic system consisting of trench, island arc, back arc basin and outer rise is often known as a convergent transitional belt between the oceanic lithosphere and the continental litho-sphere. The occurrence, development and activity of trench and outer rise bear closely on the underthrusting process of the oceanic lithosphere. A generalized analytical theory of deflection rheoevolution of lithosphere under subduction is established, and solutions with universal significance have been obtained.

  12. [Pliability and deflection of diagnostic catheters].

    Science.gov (United States)

    Pelyhe, Liza; Bognár, Eszter

    2014-09-28

    The cardiac catheter is an intravascular catheter, which is introduced or implanted into the heart for diagnostic or therapeutic reasons. The catheters may break or king during their introduction and/or removal. The aim of the authors was to study the pliability of two catheters with the same material but different diameters according to the Food and Drug Administration's recommendation. The bending points, diameter decrease, deflection, and their correlation and dependence on the distance from the tip, as well as the influence of the initial diameter of the catheters were determined. The bending of catheters was performed on 9 bending points (120-280 mm from the tip by 20 mm) on 16 gauges with different radius (10-2.5 mm by 0.5 mm). A linear dependency between the diameter decrease and deflection was observed, which was independent from the placement of the measurement in both catheters examined. The larger initial diameter had significant (p = 0.05) greater diameter decrease than the smaller, but the curves characteristic of the diameter decrease and deflection were similar. The applied method seems to be useful for the examination of weak points of cardiac catheters.

  13. Characterisation of a Mechanical Deflection Sensor

    CSIR Research Space (South Africa)

    Miyambo, M

    2012-10-01

    Full Text Available ). REFERENCES Snyman, I.M. and Reinecke, J.D. 2006. Measuring the impulse from an explosive charge, Ballistics Symposium South Africa, Denel-OTB, Bredasdorp, 15?16 Aug 2006. Miyambo, M.E. and Pandelani, T. 2012. The Mechanical Deflection Sensor Test... Mechanical Defl ection Sensor M MIYAMBO AND T PANDELANI CSIR Defence, Peace, Safety and Security, PO Box 395, Pretoria, South Africa, 0001 Email: mmiyambo@csir.co.za ? www.csir.co.za INTRODUCTION The CSIR Defence, Peace, Safety and Security (DPSS...

  14. A Bridge Deflection Monitoring System Based on CCD

    Directory of Open Access Journals (Sweden)

    Baohua Shan

    2016-01-01

    Full Text Available For long-term monitoring of the midspan deflection of Songjiazhuang cloverleaf junction on 309 national roads in Zibo city, this paper proposes Zhang’s calibration-based DIC deflection monitoring method. CCD cameras are used to track the change of targets’ position, Zhang’s calibration algorithm is introduced to acquire the intrinsic and extrinsic parameters of CCD cameras, and the DIC method is combined with Zhang’s calibration algorithm to measure bridge deflection. The comparative test between Zhang’s calibration and scale calibration is conducted in lab, and experimental results indicate that the proposed method has higher precision. According to the deflection monitoring scheme, the deflection monitoring software for Songjiazhuang cloverleaf junction is developed by MATLAB, and a 4-channel CCD deflection monitoring system for Songjiazhuang cloverleaf junction is integrated in this paper. This deflection monitoring system includes functions such as image preview, simultaneous collection, camera calibration, deflection display, and data storage. In situ deflection curves show a consistent trend; this suggests that the proposed method is reliable and is suitable for the long-term monitoring of bridge deflection.

  15. A Limited Deflection Routing Algorithm Based on Burst Loss Threshold in OBS Networks

    Institute of Scientific and Technical Information of China (English)

    WANG Ru-yan; LONG Ke-ping; WU Wei; YANG Xiao-long; ZHU Wei-le

    2005-01-01

    The deflection routing protocol is an effective contention resolution in Optical Burst Switching network. However, it can worsen loss performance of non-deflected burst on the deflection route. To improve the burst loss performance, a limited deflection routing scheme based on burst loss threshold is proposed to prevent injudicious deflection routing. By using threshold check function, it restrainedly allows the deflected burst to preemptive network resource, consequently, improve the QoS performance of non-deflected burst. Simulation results show that the scheme can efficiently prevent deflected burst contending with non-deflected burst on deflection route, and effectively improve the burst loss performance of entire networks.

  16. Deflections of Nanowires with Consideration of Surface Effects

    Institute of Scientific and Technical Information of China (English)

    LI He; YANG Zhou; ZHANG Yi-Min; WEN Bang-Chun

    2010-01-01

    @@ The elementary beam model is modified to include the surface effects and used to analyze the deflections of nanowires under different boundary conditions.The results show that compared to deflections of nanowires without consideration of surface effects,the surface effects can enlarge or reduce deflections of nanowires,and nanowire buckling occurs under certaJn conditions.This study might be helpful for design of nanowire-based nanoelectromechanical systems.

  17. Deflection of elastic beam with SMA wires eccentrically inserted

    Science.gov (United States)

    Jamian, S.; Nik Mohamed, N. A.; Ihsan, A. K. A. Mohd; Ismail, A. E.; Nor, M. K. Mohd; Kamarudin, K. A.; Nor, N. H. Muhd

    2017-08-01

    This research is intended to investigate the ability of shape memory alloys (SMA), through its activation, in generating loads to control beam deflection. An elastic beam is formed by sandwiching eccentrically SMA wires between two elastic plates. SMA wires are activated by electrical current from the power supply. Laser displacement meter (LDM) is used to measures deflection of sample. Results show that the deflection of the beam is dependent on the temperature change. The temperature-deflection response also shows the existence of hysteresis.

  18. Photon deflection by a Coulomb field in noncommutative QED

    Energy Technology Data Exchange (ETDEWEB)

    Pires, C A de S [Departamento de FIsica, Universidade Federal da ParaIba, Caixa Postal 5008, 58059-970, Joao Pessoa, PB (Brazil)

    2004-12-01

    In noncommutative QED photons present self-interactions in the form of triple and quartic interactions. The triple interaction implies that, even though the photon is electrically neutral, it will deflect when in the presence of an electromagnetic field. If detected, such deflection would be undoubted evidence of noncommutative space-time. In this work we derive a general expression for the deflection of a photon by any electromagnetic field. As an application we consider the case of the deflection of a photon by an external static Coulomb field. (brief report)

  19. Photon deflection by a Coulomb field in noncommutative QED

    CERN Document Server

    De Pires, C A S

    2004-01-01

    In noncommutative QED photons present self-interactions in the form of triple and quartic interactions. The triple interaction implies that, even though the photon is electrically neutral, it will deflect when in the presence of an electromagnetic field. If detected, such deflection would be an undoubted signal of noncommutative space-time. In this work we derive the general expression for the deflection of a photon by any electromagnetic field. As an application we consider the case of the deflection of a photon by an external static Coulomb field.

  20. Teach Deflection Concepts with Hacksaw Blades and Rubber Bands

    Science.gov (United States)

    Roman, Harry T.

    2013-01-01

    Technology and engineering educators can use a simple hacksaw blade to help students learn about deflection, as that which occurs in a beam. Here the beam is fixed at one end and allowed to deflect in a manner that is easy to see and measure--the hacksaw blade represents a cantilever, an overhanging structure. This simple and very inexpensive…

  1. Study on the causes and methods of influencing concrete deflection

    Science.gov (United States)

    Zhou, Ying; Zhou, Xiang; Tang, Jinyu

    2017-09-01

    Under the long-term effect of static load on reinforced concrete beam, the stiffness decreases and the deformation increases with time. Therefore, the calculation of deflection is more complicated. According to the domestic and foreign research results by experiment the flexural deflection of reinforced concrete, creep, age, the thickness of the protective layer, the relative slip, the combination of steel yielding factors of reinforced concrete deflection are summarized, analyzed the advantages and disadvantages of the traditional direct measurement of deflection, that by increasing the beam height, increasing the moment of inertia, ncrease prestressed reinforcement ratio, arching, reduce the load, and other measures to reduce the deflection of prestressed construction, improve the reliability of structure.

  2. Impacts of Deflection Nose on Ballistic Trajectory Control Law

    Directory of Open Access Journals (Sweden)

    Bo Zhang

    2014-01-01

    Full Text Available The deflection of projectile nose is aimed at changing the motion of the projectile in flight with the theory of motion control and changing the exterior ballistics so as to change its range and increase its accuracy. The law of external ballistics with the deflectable nose is considered as the basis of the design of a flight control system and an important part in the process of projectile development. Based on the existing rigid external ballistic model, this paper establishes an external ballistic calculation model for deflectable nose projectile and further establishes the solving programs accordingly. Different angle of attack, velocity, coefficients of lift, resistance, and moment under the deflection can be obtained in this paper based on the previous experiments and emulation researches. In the end, the author pointed out the laws on the impaction of external ballistic trajectory by the deflection of nose of the missile.

  3. Modeling and Simulating Dynamics of Missiles with Deflectable Nose Control

    Institute of Scientific and Technical Information of China (English)

    Gao Yuan; Gu Liangxian; Pan Lei

    2009-01-01

    This article investigates the dynamic characteristics of deflectable nose missiles with rotary single-channel control. After introduction of effective attack and sideslip angles as well as quasi-body coordinates based on the spin characteristics of the missile's body, an integrated rigid kinetic model of missile with deflectable nose control is set up in the quasi-body coordinates considering the interaction between the missile's nose and body by using rootless multi-rigid-body system dynamics and is linearized. Then an analysis with simulation is conducted to investigate the coupling characteristics between the channels, the influences of nose deflection on the body and the dynamic characteristics of missile's body. The results indicate that various channels of missiles with deflectable nose control are coupled cross-linked; the nose deflection tends to make the body move in the opposite direction and, finally, evidences the correctness and reasonability of the kinetic model proposed by this article.

  4. AIDA: the Asteroid Impact & Deflection Assessment mission

    Science.gov (United States)

    Vincent, Jean-Baptiste

    2016-07-01

    The Asteroid Impact & Deflection Assessment (AIDA) mission is a joint cooperation between European and US space agencies that consists of two separate and independent spacecraft that will be launched to a binary asteroid system, the near-Earth asteroid Didymos, to assess the possibility of deflecting an asteroid trajectory by using a kinetic impactor. The European Asteroid Impact Mission (AIM) is under Phase A/B1 study at ESA from March 2015 until summer 2016. AIM is set to rendez-vous with the asteroid system a few months prior to the impact by the US Double Asteroid Redirection Test (DART) spacecraft to fully characterize the smaller of the two binary components. AIM is a unique mission as it will be the first time that a spacecraft will investigate the surface, subsurface, and internal properties of a small binary near Earth asteroid. In addition it will perform various important technology demonstrations that can serve other space missions: AIM will release a set of CubeSats in deep space and a lander on the surface of the smaller asteroid and for the first time, deep-space inter-satellite linking will be demonstrated between the main spacecraft, the CubeSats, and the lander, and data will also be transmitted from interplanetary space to Earth by a laser communication system. The knowledge obtained by this mission will have great implications for our understanding of the history of the Solar System. Small asteroids are believed to result from collisions and other processes (e.g., spinup, shaking) that made them what they are now. Having direct information on their surface and internal properties will allow us to understand how these processes work and transform these small bodies as well as, for this particular case, how a binary system forms. So far, our understanding of the collisional process and the validation of numerical simulations of the impact process rely on impact experiments at laboratory scales. With DART, thanks to the characterization of the

  5. Load Deflection Characteristics of Nickel Titanium Initial Archwires

    Directory of Open Access Journals (Sweden)

    Hossein Aghili

    2016-05-01

    Full Text Available Objectives: The aim of this study was to assess and compare the characteristics of commonly used initial archwires by their load deflection graphs.Materials and Methods: This study tested three wire designs namely copper nickel titanium (CNT, nickel titanium (NiTi, and multi-strand NiTi (MSNT archwires engaged in passive self-ligating (PSL brackets, active self-ligating (ASL brackets or conventional brackets. To evaluate the mechanical characteristics of the specimens, a three-point bending test was performed. The testing machine vertically applied force on the midpoint of the wire between the central incisor and canine teeth to obtain 2 and 4mm of deflection. The force level at maximum deflection and characteristics of plateau (the average plateau load and the plateau length were recorded. Two-way ANOVA and Tukey’s test were used at P <0.05 level of significance.Results: Force level at maximum deflection and plateau length were significantly affected by the amount of deflection. The type of archwires and brackets had significant effects on force level at maximum deflection, and plateau length. However, the bracket type had no significant effect on the average plateau force.Conclusion: With any type of brackets in deflections of 2 and 4mm, MSNT wire exerted the lowest while NiTi wire exerted the highest force level at maximum deflection and plateau phase. The force level at maximum deflection and the plateau length increased with raising the amount of primary deflection; however the average plateau force did not change significantly.

  6. Coupler induced monopole component and its minimization in deflecting cavities

    Directory of Open Access Journals (Sweden)

    P. K. Ambattu

    2013-06-01

    Full Text Available Deflecting cavities are used in particle accelerators for the manipulation of charged particles by deflecting or crabbing (rotating them. For short deflectors, the effect of the power coupler on the deflecting field can become significant. The particular power coupler type can introduce multipole rf field components and coupler-specific wakefields. Coupler types that would normally be considered like standard on-cell coupler, waveguide coupler, or mode-launcher coupler could have one or two rf feeds. The major advantage of a dual-feed coupler is the absence of monopole and quadrupole rf field components in the deflecting structure. However, a dual-feed coupler is mechanically more complex than a typical single-feed coupler and needs a splitter. For most applications, deflecting structures are placed in regions where there is small space hence reducing the size of the structure is very desirable. This paper investigates the multipole field components of the deflecting mode in single-feed couplers and ways to overcome the effect of the monopole component on the beam. Significant advances in performance have been demonstrated. Additionally, a novel coupler design is introduced which has no monopole field component to the deflecting mode and is more compact than the conventional dual-feed coupler.

  7. Heavy colored SUSY partners from deflected anomaly mediation

    CERN Document Server

    Wang, Fei; Yang, Jin Min; Zhang, Yang

    2015-01-01

    We propose a deflected anomaly mediation scenario from SUSY QCD which can lead to both positive and negative deflection parameters (there is a smooth transition between these two deflection parameter regions by adjusting certain couplings). Such a scenario can naturally give a SUSY spectrum in which all the colored sparticles are heavy while the sleptons are light. As a result, the discrepancy between the Brookheaven $g_\\mu-2$ experiment and LHC data can be reconciled in this scenario. We also find that the parameter space for explaining the $g_\\mu-2$ anomaly at $1\\sigma$ level can be fully covered by the future LUX-ZEPLIN 7.2 Ton experiment.

  8. Simulations of directed energy comet deflection

    Science.gov (United States)

    Zhang, Qicheng; Lubin, Philip M.; Hughes, Gary B.

    2016-09-01

    Earth-crossing asteroids and comets pose a long-term hazard to life and property on Earth. Schemes to mitigate the impact threat have been studied extensively but tend to focus on asteroid diversion while neglecting the possibility of a comet threat. Such schemes often demand physically intercepting the target by spacecraft, a task feasible only for targets identified decades in advance in a restricted range of orbits. A threatening comet is unlikely to satisfy these criteria and so necessitates a fundamentally different approach for diversion. Comets are naturally perturbed from purely gravitational trajectories through solar heating of their surfaces which activates sublimation-driven jets. Artificial heating of a comet, such as by a high-powered laser array in Earth orbit, may supplement natural heating by the Sun to purposefully manipulate its path to avoid an impact. The effectiveness of any particular laser array for a given comet depends on the comet's heating response which varies dramatically depending on factors including nucleus size, orbit and dynamical history. These factors are incorporated into a numerical orbital model using established models of nongravitational perturbations to evaluate the effectiveness and feasibility of using high-powered laser arrays in Earth orbit or on the ground to deflect a variety of comets. Simulation results suggest that orbital arrays of 500m and 10GW operating for 10 min=d over 1 yr may be adequate for mitigating impacts by comets up to 500m in diameter. Continuously operating ground-based arrays of 100m and 10GW may be similarly effective when appropriately located.

  9. Geoid Height and Deflection of the Vertical Models

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Office of the National Geodetic Survey has produced a series of high-resolution gravimetric geoid models, hybrid geoid models, and associated deflection of the...

  10. Deflection measurements of LABAN canister sections in horizontal attitude

    Energy Technology Data Exchange (ETDEWEB)

    Wakeman, W.

    1985-01-08

    Deflection measurements made on the LABAN canister sections indicate that the apparent stiffness of its frames, with all the diagnostics experiments installed, is not significantly different from the stiffness of the bare frames.

  11. U.S. East-West Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for the conterminous United States is the DEFLEC96 model. The computationused about 1.8 million terrestrial and...

  12. U.S. North-South Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for the conterminous United States is the DEFLEC96 model. The computationused about 1.8 million terrestrial and...

  13. Hawaiian Islands North-South Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for the Principal Hawaiian Islands is the DEFLEC96 model. The computation used about 61,000 terrestrial and marine...

  14. Hawaiian Islands East-West Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for the Principal Hawaiian Islands is the DEFLEC96 model. The computation used about 61,000 terrestrial and marine...

  15. PR/VI North-South Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for Puerto Rico and the Virgin Islands is distributed as the DEFLEC96 model. The computation used about 26,000...

  16. Possible influences on bullet trajectory deflection in ballistic gelatine.

    Science.gov (United States)

    Riva, Fabiano; Kerkhoff, Wim; Bolck, Annabel; Mattijssen, Erwin J A T

    2017-02-01

    The influence of the distance to the top and bottom of a gelatine block and to bullet tracks from previously fired shots on a bullet's trajectory, when passing through ballistic gelatine, was studied. No significant difference in deflection was found when trajectories of 9mm Luger bullets, fired at a 3.5cm distance to the top and bottom of a gelatine block and to bullet tracks from previously fired shots, were compared to trajectories of bullets fired 7cm or more away from any of the aforementioned aspects. A surprisingly consistent 6.5° absolute deflection angle was found when these bullets passed through 22.5 to 23.5cm of ballistic gelatine. The projection angle, determined by the direction of the deflection, appeared to be random. The consistent absolute angle, in combination with the random projection angle, resulted in a cone-like deflection pattern.

  17. PR/VI East-West Deflections (DEFLEC96)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This 2' surface deflection of the vertical grid for Puerto Rico and the Virgin Islands is distributed as the DEFLEC96 model. The computation used about 26,000...

  18. 75 FR 12981 - Eligibility for Commercial Flats Failing Deflection

    Science.gov (United States)

    2010-03-18

    ... and June 2010. Retain current deflection standards for six more months and enlist the assistance of a Lean Six-Sigma group. Response to Comments The prices proposed in our December 2009 proposal...

  19. Deflection and Rotation of CMEs from Active Region 11158

    Science.gov (United States)

    Kay, Christina; Gopalswamy, Nat; Xie, Hong; Yashiro, Seiji

    2017-06-01

    Between 13 and 16 February 2011, a series of coronal mass ejections (CMEs) erupted from multiple polarity inversion lines within active region 11158. For seven of these CMEs we employ the graduated cylindrical shell (GCS) flux rope model to determine the CME trajectory using both Solar Terrestrial Relations Observatory (STEREO) extreme ultraviolet (EUV) and coronagraph images. We then use the model called Forecasting a CME's Altered Trajectory (ForeCAT) for nonradial CME dynamics driven by magnetic forces to simulate the deflection and rotation of the seven CMEs. We find good agreement between ForeCAT results and reconstructed CME positions and orientations. The CME deflections range in magnitude between 10^{circ } and 30^{circ}. All CMEs are deflected to the north, but we find variations in the direction of the longitudinal deflection. The rotations range between 5^{circ} and 50^{circ} with both clockwise and counterclockwise rotations. Three of the CMEs begin with initial positions within 2^{circ} from one another. These three CMEs are all deflected primarily northward, with some minor eastward deflection, and rotate counterclockwise. Their final positions and orientations, however, differ by 20^{circ} and 30^{circ}, respectively. This variation in deflection and rotation results from differences in the CME expansion and radial propagation close to the Sun, as well as from the CME mass. Ultimately, only one of these seven CMEs yielded discernible in situ signatures near Earth, although the active region faced toward Earth throughout the eruptions. We suggest that the differences in the deflection and rotation of the CMEs can explain whether each CME impacted or missed Earth.

  20. Deflection load characteristics of laser-welded orthodontic wires.

    Science.gov (United States)

    Watanabe, Etsuko; Stigall, Garrett; Elshahawy, Waleed; Watanabe, Ikuya

    2012-07-01

    To compare the deflection load characteristics of homogeneous and heterogeneous joints made by laser welding using various types of orthodontic wires. Four kinds of straight orthodontic rectangular wires (0.017 inch × 0.025 inch) were used: stainless-steel (SS), cobalt-chromium-nickel (Co-Cr-Ni), beta-titanium alloy (β-Ti), and nickel-titanium (Ni-Ti). Homogeneous and heterogeneous end-to-end joints (12 mm long each) were made by Nd:YAG laser welding. Two types of welding methods were used: two-point welding and four-point welding. Nonwelded wires were also used as a control. Deflection load (N) was measured by conducting the three-point bending test. The data (n  =  5) were statistically analyzed using analysis of variance/Tukey test (P welded specimens showed lower deflection loads compared to corresponding control wires and exhibited higher deflection loads compared to heterogeneously welded combinations. For homogeneous combinations, Co-Cr-Ni/Co-Cr-Ni showed a significantly (P welded groups. In heterogeneous combinations, SS/Co-Cr-Ni and β-Ti/Ni-Ti showed higher deflection loads than those of the remaining heterogeneously welded combinations (significantly higher for SS/Co-Cr-Ni). Significance (P welding method). However, no significant difference in deflection load was found between four-point and two-point welding in each homogeneous or heterogeneous combination. Heterogeneously laser-welded SS/Co-Cr-Ni and β-Ti/Ni-Ti wires provide a deflection load that is comparable to that of homogeneously welded orthodontic wires.

  1. Large deflection analysis of cantilever beam under end point and distributed load

    DEFF Research Database (Denmark)

    Kimiaeifar, Amin; Tolou, N; Barari, Amin;

    2014-01-01

    Although the deflection of beams has been studied for decades, the solutions were either linearized (i.e. small deflection) or based on elliptic integrals or functions (large deflection). The latter one includes the geometric nonlinearity but calculation of the deflection along the beam length re...

  2. Needle deflection estimation using fusion of electromagnetic trackers.

    Science.gov (United States)

    Sadjadi, H; Hashtrudi-Zaad, K; Fichtinger, G

    2012-01-01

    We present a needle deflection estimation method to compensate for needle bending during insertion into deformable tissue. We combine a kinematic needle deflection estimation model, electromagnetic (EM) trackers, and a Kalman filter (KF). We reduce the impact of error from the needle deflection estimation model by using the fusion of two EM trackers to report the approximate needle tip position in real-time. One reliable EM tracker is installed on the needle base, and estimates the needle tip position using the kinematic needle deflection model. A smaller but much less reliable EM tracker is installed on the needle tip, and estimates the needle tip position through direct noisy measurements. Using a KF, the sensory information from both EM trackers is fused to provide a reliable estimate of the needle tip position with much reduced variance in the estimation error. We then implement this method to compensate for needle deflection during simulated prostate cancer brachytherapy needle insertion. At a typical maximum insertion depth of 15 cm, needle tip mean estimation error was reduced from 2.39 mm to 0.31 mm, which demonstrates the effectiveness of our method, offering a clinically practical solution.

  3. Ultrafast optical beam deflection in a pump probe configuration

    Science.gov (United States)

    Liang, Lingliang; Tian, Jinshou; Wang, Tao; Wu, Shengli; Li, Fuli; Wang, Junfeng; Gao, Guilong

    2016-09-01

    Propagation of a signal beam in an AlGaAs/GaAs waveguide multiple-prism light deflector is theoretically investigated by solving the scalar Helmholtz equation to obtain the dependences of the temporal and spatial resolvable characteristics of the ultrafast deflector on the material dispersion of GaAs including group velocity dispersion and angular dispersion, interface reflection, and interface scattering of multiple-prism deflector. Furthermore, we experimentally confirm that, in this ultrafast beam deflection device, the deflecting angle of the signal light beam is linear with the pump fluence and the temporal resolution of the ultrafast deflection is 10 ps. Our results show that the improvement of the temporal and spatial resolvable performances is possible by properly choosing the structural parameters and enhancing the quality of the device. Project supported by the National Natural Science Foundation of China (Grant Nos. 11274377 and 61176006) and the State Major Research Equipment Project, China (Grant No. ZDY2011-2).

  4. ABRUPT DEFLECTED SUPERCRITICAL WATER FLOW IN SLOPED CHANNELS

    Institute of Scientific and Technical Information of China (English)

    LIU Ya-kun; NI Han-gen

    2008-01-01

    The effect of the bottom slope on abrupt deflected supercritical water flow was experimentally and theoretically studied. Model tests were conducted in a flume of 1.2 m wide and 2.6 m long with sloped bottom at an angle 35.54o, its length of deflector was 0.2 m and the deflection angles were 15o and 30o. An approximate method for calculatjng the shock wave angle and depth ratio of the abrupt deflected supercritical water flow was suggested, and a correction coefficient for the hydrodynamic pressure was introduced to generalize the momentum equation in the direction perpendicular to the shock front. It must be noticed that in the sloped channel the shock wave angle and the depth ratio are no longer constant as those in the horizontal channels, but slowly change along the shock front. The calculated results are in good agreement with measured data.

  5. Linearizing Intra-Train Beam-Beam Deflection Feedback

    Energy Technology Data Exchange (ETDEWEB)

    Smith, S.R.; /SLAC

    2006-02-22

    Beam-beam deflection feedback acting within the crossing time of a single bunch train may be needed to keep linear collider beams colliding at high luminosity. In a short-pulse machine such as the Next Linear Collider (NLC) this feedback must converge quickly to be useful. The non-linear nature of beam-beam deflection vs. beam-beam offset in these machines precludes obtaining both rapid convergence and a stable steady-state lock to beam offsets with a linear feedback algorithm. We show that a simply realizable programmable non-linear amplifier in the feedback loop can linearize the feedback loop, approximately compensating the beam-beam deflection non-linearity. Performance of a prototype non-linear amplifier is shown. Improvement of convergence and stability of the beam-beam feedback loop is simulated.

  6. Novel deflecting cavity design for eRHIC

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Q.; Belomestnykh, S.; Ben-Zvi, I.

    2011-07-25

    To prevent significant loss of the luminosity due to large crossing angle in the future ERL based Electron Ion Collider at BNL (eRHIC), there is a demand for crab cavities. In this article, we will present a novel design of the deflecting/crabbing 181 MHz superconducting RF cavity that will fulfil the requirements of eRHIC. The quarter-wave resonator structure of the new cavity possesses many advantages, such as compact size, high R{sub t}/Q, the absence of the same order mode and lower order mode, and easy higher order mode damping. We will present the properties and characteristics of the new cavity in detail. As the accelerator systems grow in complexity, developing compact and efficient deflecting cavities is of great interest. Such cavities will benefit situations where the beam line space is limited. The future linac-ring type electron-ion collider requires implementation of a crab-crossing scheme for both beams at the interaction region. The ion beam has a long bunches and high rigidity. Therefore, it requires a low frequency, large kicking angle deflector. The frequency of the deflecting mode for the current collider design is 181 MHz, and the deflecting angle is {approx}5 mrad for each beam. At such low frequency, the previous designs of the crab cavities will have very large dimensions, and also will be confronted by typical problems of damping the Lower Order Mode (LOM), the Same Order Mode (SOM), and as usual, the Higher Order Modes (HOM). In this paper we describe how one can use the concept of a quarter-wave (QW) resonator for a deflecting/crabbing cavity, and use its fundamental mode to deflect the beam. The simplicity of the cavity geometry and the large separation between its fundamental mode and the first HOM make it very attractive.

  7. Two-mode polarized traveling wave deflecting structure

    Institute of Scientific and Technical Information of China (English)

    谭建豪; 顾强; 方文程; 童德春; 赵振堂

    2015-01-01

    In this paper, we propose a two-mode polarizable deflecting structure, as a new concept for bunch measure-ment and beam control. With two modes of HEM11 and HEM12 operating in the same structure on horizontal and vertical directions, respectively, the operation status can be switched between the two polarization modes. They can be operated simultaneously with two independent input power sources. With two-mode deflecting structure, the bunch distortion caused by the geometric wake-fields in the accelerating structure can be mea-sured by one structure.

  8. Nuclear cycler: An incremental approach to the deflection of asteroids

    Science.gov (United States)

    Vasile, Massimiliano; Thiry, Nicolas

    2016-04-01

    This paper introduces a novel deflection approach based on nuclear explosions: the nuclear cycler. The idea is to combine the effectiveness of nuclear explosions with the controllability and redundancy offered by slow push methods within an incremental deflection strategy. The paper will present an extended model for single nuclear stand-off explosions in the proximity of elongated ellipsoidal asteroids, and a family of natural formation orbits that allows the spacecraft to deploy multiple bombs while being shielded by the asteroid during the detonation.

  9. Multiplexed Force and Deflection Sensing Shell Membranes for Robotic Manipulators

    Science.gov (United States)

    Park, Yong-Lae; Black, Richard; Moslehi, Behzad; Cutkosky, Mark; Chau, Kelvin

    2012-01-01

    Force sensing is an essential requirement for dexterous robot manipulation, e.g., for extravehicular robots making vehicle repairs. Although strain gauges have been widely used, a new sensing approach is desirable for applications that require greater robustness, design flexibility including a high degree of multiplexibility, and immunity to electromagnetic noise. This invention is a force and deflection sensor a flexible shell formed with an elastomer having passageways formed by apertures in the shell, with an optical fiber having one or more Bragg gratings positioned in the passageways for the measurement of force and deflection.

  10. Research on network failure handling technology based on deflection routing

    Institute of Scientific and Technical Information of China (English)

    Tao YU; Shanzhi CHEN; Xin LI; Zhen QIN

    2008-01-01

    A new deflection routing scheme is proposed to overcome the drawback of existing deflection routing scheme that cannot handle node failure and suffer from routing loops.A new algorithm for computing the backup shortest path tree(SPT)is proposed and a set of procedures are defined for utilizing the backup SPT in case of node or link failure.The failure can be handled swiftly and the backup routes are guaranteed to be loop-free.Experimental results show that the backup routes calculated by proposed scheme are close to the optimal routes by totally re-computing.

  11. The 1919 measurement of the deflection of light

    CERN Document Server

    Will, Clifford M

    2014-01-01

    The measurement of the deflection of starlight during a total solar eclipse on May 29, 1919 was the first verification of general relativity by an external team of scientists, brought Einstein and his theory to the attention of the general public, and left a legacy of experimental testing that continues today. The discovery of gravitational lenses turned Einstein's deflection into an important tool for astronomy and cosmology. This article reviews the history of the 1919 measurement and other eclipse measurements, describes modern measurements of the effect using radio astronomy, and of its cousin, the Shapiro time delay, and discusses gravitational lenses.

  12. The effect of asteroid topography on surface ablation deflection

    Science.gov (United States)

    McMahon, Jay W.; Scheeres, Daniel J.

    2017-02-01

    Ablation techniques for deflecting hazardous asteroids deposit energy into the asteroid's surface, causing an effective thrust on the asteroid as the ablating material leaves normal to the surface. Although it has long been recognized that surface topography plays an important role in determining the deflection capabilities, most studies to date have ignored this aspect of the model. This paper focuses on understanding the topography for real asteroid shapes, and how this topography can change the deflection performance of an ablation technique. The near Earth asteroids Golevka, Bennu, and Itokawa are used as the basis for this study, as all three have high-resolution shape models available. This paper shows that naive targeting of an ablation method without accounting for the surface topography can lower the deflection performance by up to 20% in the cases studied in terms of the amount of acceleration applied in the desired direction. If the ablation thrust level is assumed to be 100 N, as used elsewhere in the literature, this misapplication of thrust translates to tens of kilometers per year in decreased semimajor axis change. However, if the ablation method can freely target any visible point on the surface of the asteroid, almost all of this performance can be recovered.

  13. Deflection of Light by Gravity: A Physical Approach.

    Science.gov (United States)

    Diamond, Joshua B.

    1982-01-01

    Einstein's equivalence principle relates effects seen by an accelerating observer to those experienced by an observer in a gravitational field, providing an explanation of bending of a light beam by gravity. Because the calculations lead to results one-half the value found experimentally, obtaining the correct light deflection is discussed.…

  14. On guided versus deflected fields in controlled-source electromagnetics

    Science.gov (United States)

    Swidinsky, Andrei

    2015-06-01

    The detection of electrically resistive targets in applied geophysics is of interest to the hydrocarbon, mining and geotechnical industries. Elongated thin resistive bodies have been extensively studied in the context of offshore hydrocarbon exploration. Such targets guide electromagnetic fields in a process which superficially resembles seismic refraction. On the other hand, compact resistive bodies deflect current in a process which has more similarities to diffraction and scattering. The response of a real geological structure is a non-trivial combination of these elements-guiding along the target and deflection around its edges. In this note the electromagnetic responses of two end-member models are compared: a resistive layer, which guides the electromagnetic signal, and a resistive cylinder, which deflects the fields. Results show that the response of a finite resistive target tends to saturate at a much lower resistivity than a resistive layer, under identical survey configurations. Furthermore, while the guided electromagnetic fields generated by a buried resistive layer contain both anomalous horizontal and vertical components, the process of electromagnetic deflection from a buried resistive cylinder creates mainly anomalous vertical fields. Finally, the transmitter orientation with respect to the position of a finite body is an important survey parameter: when the distance to the target is much less than the host skin depth, a transmitter pointing towards the resistive cylinder will produce a stronger signal than a transmitter oriented azimuthally with respect to the cylinder surface. The opposite situation is observed when the distance to the target is greater than the host skin depth.

  15. Mission Design and Optimal Asteroid Deflection for Planetary Defense

    Science.gov (United States)

    Sarli, Bruno V.; Knittel, Jeremy M.; Englander, Jacob A.; Barbee, Brent W.

    2017-01-01

    Planetary defense is a topic of increasing interest for many reasons, which has been mentioned in "Vision and Voyages for Planetary Science in the Decade 2013-2022''. However, perhaps one of the most significant rationales for asteroid studies is the number of close approaches that have been documented recently. A space mission with a planetary defense objective aims to deflect the threatening body as far as possible from Earth. The design of a mission that optimally deflects an asteroid has different challenges: speed, precision, and system trade-off. This work addresses such issues and develops a fast transcription of the problem that can be implemented into an optimization tool, which allows for a broader trade study of different mission concepts with a medium fidelity. Such work is suitable for a mission?s preliminary study. It is shown, using the fictitious asteroid impact scenario 2017 PDC, that the complete tool is able to account for the orbit sensitivity to small perturbations and quickly optimize a deflection trajectory. The speed in which the tool operates allows for a trade study between the available hardware. As a result, key deflection dates and mission strategies are identified for the 2017 PDC.

  16. Mission Design and Optimal Asteroid Deflection for Planetary Defense

    Science.gov (United States)

    Sarli, Bruno V.; Knittel, Jeremy M.; Englander, Jacob A.; Barbee, Brent W.

    2017-01-01

    Planetary defense is a topic of increasing interest for many reasons, which has been mentioned in "Vision and Voyages for Planetary Science in the Decade 2013-2022". However, perhaps one of the most significant rationales for asteroid studies is the number of close approaches that have been documented recently. A space mission with a planetary defense objective aims to deflect the threatening body as far as possible from Earth. The design of a mission that optimally deflects an asteroid has different challenges: speed, precision, and system trade-off. This work addresses such issues and develops a fast transcription of the problem that can be implemented into an optimization tool, which allows for a broader trade study of different mission concepts with a medium fidelity. Such work is suitable for a mission's preliminary study. It is shown, using the fictitious asteroid impact scenario 2017 PDC, that the complete tool is able to account for the orbit sensitivity to small perturbations and quickly optimize a deflection trajectory. The speed in which the tool operates allows for a trade study between the available hardware. As a result, key deflection dates and mission strategies are identified for the 2017 PDC.

  17. Large deflection analysis of skew plates under uniformly distributed ...

    African Journals Online (AJOL)

    user

    load-deflection plane to show the effect of skew angle, aspect ratio and boundary condition. ... by edge 1, 2, 3 and 4 on the plate boundaries in Figures 1(a)-1(d). ... one-dimensional coordinate functions along normalized coordinate are shown ...

  18. An Analytical Model of Wake Deflection Due to Shear Flow

    NARCIS (Netherlands)

    Micallef, D.; Simao Ferreira, C.J.; Sant, T.; Van Bussel, G.J.W.

    2010-01-01

    The main motivation behind this work is to create a purely analytical engineering model for wind turbine wake upward deflection due to shear flow, by developing a closed form solution of the velocity field due to an oblique vortex ring. The effectiveness of the model is evaluated by comparing the re

  19. Deflection routing scheme for GMPLS-based OBS networks

    DEFF Research Database (Denmark)

    Eid, Arafat; Mahmood, Waqar; Alomar, Anwar

    2010-01-01

    is not applicable in such an integrated solution. This is due to the existence of already established Label Switched Paths (LSPs) between edge nodes in a GMPLS-based OBS network which guide the Data Burst Headers (DBHs) through the network. In this paper we propose a novel deflection routing scheme which can...

  20. Towards a mechanistic analysis of Benkelman beam deflection measurements

    NARCIS (Netherlands)

    Visser, A.F.H.M.; Priambodo Koesrindartono, D.

    2000-01-01

    This paper introduces and describes the Benkelman beam deflection test. Furthermore Benkelman beam tests are simulated using two multi-layer programs, based on an elastic and visco-elastic material model for asphalt. The results of these two programs are compared with each other. Finally, using the

  1. Cantilever deflection measurement and actuation by an nterdigitated transducer

    NARCIS (Netherlands)

    Strambini, E.; Piazza, V.; Pingue, P.; Biasiol, G.; Sorba, L.; Beltram, F.

    2010-01-01

    A scheme that allows all-electrical high-bandwidth readout of a cantilever deflection by means of an integrated interdigitated transducer is presented. The present approach takes advantage of the piezoelectricity of the chosen cantilever substrate material to generate and detect surface-acoustic-wav

  2. Electro-optical approach to pavement deflection management

    Science.gov (United States)

    Rish, Jeff W., III; Adcock, Avery D.; Tuan, Christopher Y.; Baker, Samuel L.; Welker, Hugh W., II; Johnson, Roger F.

    1995-07-01

    A prototype continuous deflection device, referred to as a rolling weight deflectometer (RWD), has been developed as a nondestructive evaluation tool for airfield pavements. The system consists of a rigid trailer equipped with specially designed optical triangulation pavement sensors, a high-speed data acquisition system, and a high-pressure tire/load platform assembly. Pavement sensors are mounted on a rigid box beam equipped with an internal sensor system that corrects, in real time, the relative pavement height position measurements for displacements induced in the beam by mechanical vibrations, changes in temperature, or nonuniform dynamic loads at points where the beam attaches to the frame. The device produces continuous deflection profiles that show pavement response to a moving loaded wheel along the path of travel. These deflection profiles, combined with multiple passes along a lane, provide a far more detailed picture of the pavement structural integrity than has ever before been possible, because existing evaluation tools only produce response information at discrete points. Preliminary results show deflections measured by the RWD are in general agreement with the expected pavement response for various loads. A discussion of the device configuration, preliminary data, and potential as a pavement management tool is presented.

  3. Observation of Beam-beam Deflections with LHC Orbit Data

    CERN Document Server

    Kozanecki, W; Wenninger, J

    2013-01-01

    The LHC luminosity is calibrated in dedicated fills with van der Meer scans (vdM) of the beams that are performed repeatedly in both planes. During vdM scans the relative separation of the two LHC beams is scanned in a range of ±6 sigma , where sigma is the single beam size, probing the beam-beam deflection over a relatively large range. Orbit data logged parasitically during those scans were analysed and the beam-beam deflections at the IP being scanned could be reconstructed from orbit fits in the LHC arcs surrounding the IP. Despite the small size of the kicks (≤ 1μrad) the coherent beam-beam deflections are clearly resolved. The beam parameters that are extracted from the fit to the beam-beam deflection data were compared to luminosity data fits and they were found to be in good agreement. The closed orbit shift due to the beam-beam kick is also clearly observed in the beam position interpolation at the collision point.

  4. Free Vibration Analysis of Rectangular Orthotropic Membranes in Large Deflection

    Directory of Open Access Journals (Sweden)

    Zheng Zhou-Lian

    2009-01-01

    Full Text Available This paper reviewed the research on the vibration of orthotropic membrane, which commonly applied in the membrane structural engineering. We applied the large deflection theory of membrane to derive the governing vibration equations of orthotropic membrane, solved it, and obtained the power series formula of nonlinear vibration frequency of rectangular membrane with four edges fixed. The paper gave the computational example and compared the two results from the large deflection theory and the small one, respectively. Results obtained from this paper provide some theoretical foundation for the measurement of pretension by frequency method; meanwhile, the results provide some theoretical foundation for the research of nonlinear vibration of membrane structures and the response solving of membrane structures under dynamic loads.

  5. Jet deflection by very weak guide fields during magnetic reconnection.

    Science.gov (United States)

    Goldman, M V; Lapenta, G; Newman, D L; Markidis, S; Che, H

    2011-09-23

    Previous 2D simulations of reconnection using a standard model of initially antiparallel magnetic fields have detected electron jets outflowing from the x point into the ion outflow exhausts. Associated with these jets are extended "outer electron diffusion regions." New PIC simulations with an ion to electron mass ratio as large as 1836 (an H(+) plasma) now show that the jets are strongly deflected and the outer electron diffusion region is broken up by a very weak out-of-plane magnetic guide field, even though the diffusion rate itself is unchanged. Jet outflow and deflection are interpreted in terms of electron dynamics and are compared to recent measurements of jets in the presence of a small guide field in Earth's magnetosheath.

  6. Estimation of the deflection of the vertical using gravity measurements

    Science.gov (United States)

    Manoussakis, Gerassimos; Korakitis, Romylos; Milas, Paraskevas

    2017-04-01

    We present a method to estimate the deflection of the vertical at a point P on the Earth's physical surface by forming a small network of three points around point P, with known geodetic coordinates (φ, λ, h) and by obtaining gravity measurements at all points. In the first step, the gravity values are used to form the Eötvös matrix of the actual gravity potential W at point P. In the second step, the gravity differences and the components of the Eötvös matrix are used to form a linear system of three algebraic equations with three unknowns, which are the first order partial derivatives of the actual potential W. The solution of the system enables us to determine the components ξ and η of the deflection of the vertical at the chosen point P. Finally, we present a numerical simulation, using several points scattered on a wide area of the Earth's surface.

  7. Deflection of Rotating Symmetric Molecules by Inhomogeneous Fields

    CERN Document Server

    Gershnabel, Erez

    2011-01-01

    We consider deflection of rotating symmetric molecules by inhomogeneous optical and static electric fields, compare results with the case of linear molecules, and find new singularities in the distribution of the scattering angle. Scattering of the prolate/oblate molecules is analyzed in detail, and it is shown that the process can be efficiently controlled by means of short and strong femtosecond laser pulses. In particular, the angular dispersion of the deflected molecules may be dramatically reduced by laser-induced molecular pre-alignment. We first study the problem by using a simple classical model, and then find similar results by means of more sophisticated methods, including the formalism of adiabatic invariants and direct numerical simulation of the Euler-Lagrange equations of motion. The suggested control scheme opens new ways for many applications involving molecular focusing, guiding, and trapping by optical and static fields.

  8. Measurement of Large Forces and Deflections in Microstructures

    CERN Document Server

    Hals, Kai Axel; Chen, Xuyuan

    2008-01-01

    Properties of typical MEMS materials have been widely investigated. Mechanical properties of MEMS structures depend not only on the bulk material properties, but also structural factors. A measurement system has been made to measure force/deflection on microstructures to examine some of the structural properties. This is a stylus setup integrated with a load cell and a linear actuator. First, the requirements for the measurement system were established. Then the system was built up and characterized. We have successfully made measurements on a typical micromechanical structure, a cantilever accelerometer design. The stylus placement accuracy, the spring constant along the proof mass, analysis of the force/deflection curve shape and destructive tests on the cantilever have been investigated in our experiment and will be presented in this paper.

  9. Strong deflection gravitational lensing by a modified Hayward black hole

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Shan-Shan; Xie, Yi [Nanjing University, School of Astronomy and Space Science, Nanjing (China); Nanjing University, Ministry of Education, Key Laboratory of Modern Astronomy and Astrophysics, Nanjing (China)

    2017-05-15

    A modified Hayward black hole is a nonsingular black hole. It is proposed that it would form when the pressure generated by quantum gravity can stop matter's collapse as the matter reaches the Planck density. Strong deflection gravitational lensing occurring nearby its event horizon might provide some clues of these quantum effects in its central core. We investigate observables of the strong deflection lensing, including angular separations, brightness differences and time delays between its relativistic images, and we estimate their values for the supermassive black hole in the Galactic center. We find that it is possible to distinguish the modified Hayward black hole from a Schwarzschild one, but it demands a very high resolution, beyond current stage. (orig.)

  10. A map of UHECRs deflections through the turbulent GMF

    Energy Technology Data Exchange (ETDEWEB)

    Pshirkov, M.S. [Sternberg Astronomical Institute, Lomonosov Moscow State University, Universitetsky Prospekt 13, 119992 Moscow (Russian Federation); Pushchino Radio Astronomy Observatory, 142290 Pushchino (Russian Federation); Institute for Nuclear Research of the Russian Academy of Sciences, 117312 Moscow (Russian Federation); Tinyakov, P.G. [Institute for Nuclear Research of the Russian Academy of Sciences, 117312 Moscow (Russian Federation); Université Libre de Bruxelles, Service de Physique Théorique, CP225, 1050 Brussels (Belgium); Urban, F.R. [Université Libre de Bruxelles, Service de Physique Théorique, CP225, 1050 Brussels (Belgium)

    2014-04-01

    We study the effect of the random part of the Galactic Magnetic Field (GMF) on the propagation of ultra high-energy cosmic rays. We are able to derive a clear and direct relation between the observed variance of rotation measures and the predicted cosmic ray deflections, which puts a solid upper limit of the experimentally observed displacements. Remarkably, this is obtained bypassing entirely the detailed knowledge of the magnetic properties of the turbulent plasma, and that of the electron density variance. Over most of the sky the random deflections for 40 EeV protons do not exceed 1–2°, and can be as large as 5° close to the Galactic plane.

  11. SUPERCONDUCTING RF-DIPOLE DEFLECTING AND CRABBING CAVITIES

    Energy Technology Data Exchange (ETDEWEB)

    Delayen, Jean [ODU, JLAB; De Silva, Paygalage Subashini [ODU, JLAB

    2013-09-01

    Recent interests in designing compact deflecting and crabbing structures for future accelerators and colliders have initiated the development of novel rf structures. The superconducting rf-dipole cavity is one of the first compact designs with attractive properties such as higher gradients, higher shunt impedance, the absence of lower order modes and widely separated higher order modes. Two rf-dipole designs of 400 MHz and 499 MHz have been designed, fabricated and tested as proof-of-principle designs of compact deflecting and crabbing cavities for the LHC high luminosity upgrade and Jefferson Lab 12 GeV upgrade. The first rf tests have been performed on the rf-dipole geometries at 4.2 K and 2.0 K in a vertical test assembly with excellent results. The cavities have achieved high gradients with high intrinsic quality factors, and multipacting levels were easily processed.

  12. Prediction of Double Layer Grids' Maximum Deflection Using Neural Networks

    Directory of Open Access Journals (Sweden)

    Reza K. Moghadas

    2008-01-01

    Full Text Available Efficient neural networks models are trained to predict the maximum deflection of two-way on two-way grids with variable geometrical parameters (span and height as well as cross-sectional areas of the element groups. Backpropagation (BP and Radial Basis Function (RBF neural networks are employed for the mentioned purpose. The inputs of the neural networks are the length of the spans, L, the height, h and cross-sectional areas of the all groups, A and the outputs are maximum deflections of the corresponding double layer grids, respectively. The numerical results indicate that the RBF neural network is better than BP in terms of training time and performance generality.

  13. Effect of layer length on deflection in sandwich beams

    Science.gov (United States)

    Abbu, Muthanna A.; AL-Ameri, Riyadh

    2017-09-01

    A theoretical study has been carried out on sandwich beams strengthened mechanically by two external steel plates attached to their tension and compression sides with so-called "shear connectors ". This study is based on the individual behaviour of each component of the composite sandwich section (i.e. reinforced concrete beam and upper steel plate and lower steel plate). The approach has been developed to simulate the behaviour of such beams, and is based on neglecting the separation between the three layers; i.e., the deflections are equal in each element through the same section. The differential equations reached were solved analytically. Deflection was calculated by using the approach for several beams, tested in two series, and close agreements were obtained with the experimental values. Furthermore, the interaction efficiency between the three elements in a composite sandwich beam has been considered thoroughly, from which the effect of some parameters, such as plate length upon the behaviour of such beams, were studied.

  14. Deflection of Resilient Materials for Reduction of Floor Impact Sound

    OpenAIRE

    Jung-Yoon Lee; Jong-Mun Kim

    2014-01-01

    Recently, many residents living in apartment buildings in Korea have been bothered by noise coming from the houses above. In order to reduce noise pollution, communities are increasingly imposing bylaws, including the limitation of floor impact sound, minimum thickness of floors, and floor soundproofing solutions. This research effort focused specifically on the deflection of resilient materials in the floor sound insulation systems of apartment houses. The experimental program involved condu...

  15. Galvanometer deflection: a precision high-speed system.

    Science.gov (United States)

    Jablonowski, D P; Raamot, J

    1976-06-01

    An X-Y galvanometer deflection system capable of high precision in a random access mode of operation is described. Beam positional information in digitized form is obtained by employing a Ronchi grating with a sophisticated optical detection scheme. This information is used in a control interface to locate the beam to the required precision. The system is characterized by high accuracy at maximum speed and is designed for operation in a variable environment, with particular attention placed on thermal insensitivity.

  16. Mechanical radiation detection via sub-Brownian lever deflections

    Science.gov (United States)

    Hammig, Mark David

    2005-07-01

    A micromechanical lever that deflects in response to the impacts of charged particles is proposed as a means of improving upon the capabilities of existing radiation detection technology. When a particle strikes an object, momentum is transferred to the impacted body. The resulting body motion can be correlated to the energy of the incident particle. The momentum detector offers promise as a highly discriminating, high-resolution tool for ion sensing. Advances required to successfully realize a spectroscopic capability have been completed; specifically, techniques for reproducibly fabricating micromechanical structures have been optimized, and an instrument that measures miniscule deflections has been developed. Even absent substantial refinement efforts, the novel coupled-cavity optical detector can resolve lever motions on the order of 1--10 picometers. A method by which the Brownian motion of the lever can be stilled has been proven which elicits reductions sufficient to measure heavy-ion impact, the deflections from which may be several orders of magnitude below the thermal vibration amplitude. Using active forcing techniques, the Brownian vibration of the microlevers has been reduced from room temperature (288 K) to sub-Kelvin temperatures, for levers vibrating in air. The mechanical factors that limit the noise reduction magnitude are discussed and methods of surmounting those limitations are identified.

  17. Stiffness and Angular Deflection analysis of Revolute Manipulator

    Directory of Open Access Journals (Sweden)

    Pundru Srinivasa Rao

    2014-03-01

    Full Text Available This paper proposed to determine the Cartesian stiffness matrix and angular deflection analysis of revolute manipulator. The selected manipulator has rigid fixed link, two movable links and two rotary joints with joint stiffness coefficients are taken into account. The kinematic model of revolute joint manipulator has considered as a planar kinematic chain, which is composed by rigid fixed link and two revolute joints with clearance and deformable elements. The calculation of stiffness matrix depends on Jacobian matrix and change of configuration. The rotational joints are modeled as torsion springs with the same stiffness constant. The relative angular deflections are proportional to the actuated torques taken into account. The subject of this paper has to describe a method for stiffness analysis of serial manipulator. In the present work is to derive the stiffness matrix and angular deflection equations in the Robotic manipulator under the consideration of two-link optimum geometry model for rotary joint manipulator. The stiffness values are measured by displacements of its revolute links loaded by force.

  18. Comparison Between Two Solutions Based on the Relationship of Load-deflection Character of a Large Deflection Rubber Circular Plate

    Institute of Scientific and Technical Information of China (English)

    段浩; 胡宗武; 杨赪石; 黎佑铭

    2003-01-01

    The rubber circular plate is considered as a kind of membrane. Based on the character that there existsno bending-moment inside a membrane, the geometric behavior of the rubber circular plate in expanding state wasdescribed with the aid of a group of mathematic method. The relationship between deflection and load was attainedby means of calculating stress and strain inside the curved-surface of rubber plate. Meantime, based on Henckymethod, the relationship between deflection and load was attained and considered as the Hencky solution. The dif-ferent results given rise by the two different resolving methods were compared. The deviation results from theHencky method was discussed, and a kind of correcting method was put forward.

  19. Deflection unit for multi-beam mask making

    Science.gov (United States)

    Letzkus, Florian; Butschke, Joerg; Irmscher, Mathias; Jurisch, Michael; Klingler, Wolfram; Platzgummer, Elmar; Klein, Christof; Loeschner, Hans; Springer, Reinhard

    2008-10-01

    Two main challenges of future mask making are the decreasing throughput of the pattern generators and the insufficient line edge roughness of the resist structures. The increasing design complexity with smaller feature sizes combined with additional pattern elements of the Optical Proximity Correction generates huge data volumes which reduce correspondingly the throughput of conventional single e-beam pattern generators. On the other hand the achievable line edge roughness when using sensitive chemically amplified resists does not fulfill the future requirements. The application of less sensitive resists may provide an improved roughness, however on account of throughput, as well. To overcome this challenge a proton multi-beam pattern generator is developed [1]. Starting with a highly parallel broad beam, an aperture-plate is used to generate thousands of separate spot beams. These beams pass through a blanking-plate unit, based on a CMOS device for de-multiplexing the writing data and equipped with electrodes placed around the apertures switching the beams "on" or "off", dependent on the desired pattern. The beam array is demagnified by a 200x reduction optics and the exposure of the entire substrate is done by a continuous moving stage. One major challenge is the fabrication of the required high aspect deflection electrodes and their connection to the CMOS device. One approach is to combine a post-processed CMOS chip with a MEMS component containing the deflection electrodes and to realize the electrical connection of both by vertical integration techniques. For the evaluation and assessment of this considered scheme and fabrication technique, a proof-of-concept deflection unit has been realized and tested. Our design is based on the generation of the deflection electrodes in a silicon membrane by etching trenches and oxide filling afterwards. In a 5mm x 5mm area 43,000 apertures with the corresponding electrodes have been structured and wired individually or in

  20. Deflection by kinetic impact: Sensitivity to asteroid properties

    Science.gov (United States)

    Bruck Syal, Megan; Michael Owen, J.; Miller, Paul L.

    2016-05-01

    Impacting an asteroid with a spacecraft traveling at high speed delivers an impulsive change in velocity to the body. In certain circumstances, this strategy could be used to deflect a hazardous asteroid, moving its orbital path off of an Earth-impacting course. However, the efficacy of momentum delivery to asteroids by hypervelocity impact is sensitive to both the impact conditions (particularly velocity) and specific characteristics of the target asteroid. Here we numerically model asteroid response to kinetic impactors under a wide range of initial conditions, using an Adaptive Smoothed Particle Hydrodynamics code. Impact velocities spanning 1-30 km/s were investigated, yielding, for a particular set of assumptions about the modeled target material, a power-law dependence consistent with a velocity-scaling exponent of μ = 0.44. Target characteristics including equation of state, strength model, porosity, rotational state, and shape were varied, and corresponding changes in asteroid response were documented. The kinetic-impact momentum-multiplication factor, β, decreases with increasing asteroid cohesion and increasing porosity. Although increased porosity lowers β, larger porosities result in greater deflection velocities, as a consequence of reduced target masses for asteroids of fixed size. Porosity also lowers disruption risk for kinetic impacts near the threshold of disruption. Including fast (P = 2.5 h) and very fast (P = 100 s) rotation did not significantly alter β but did affect the risk of disruption by the impact event. Asteroid shape is found to influence the efficiency of momentum delivery, as local slope conditions can change the orientation of the crater ejecta momentum vector. These results emphasize the need for asteroid characterization studies to bracket the range of target conditions expected at near-Earth asteroids while also highlighting some of the principal uncertainties associated with the kinetic-impact deflection strategy.

  1. The 2017 Eclipse: Centenary of the Einstein Light Deflection Experiment

    Science.gov (United States)

    Kennefick, Daniel

    2017-01-01

    August 21st, 2017 will see a total eclipse of the Sun visible in many parts of the United States. Coincidentally this date marks the centenary of the first observational attempt to test Einstein's General Theory of Relativity by measuring gravitational deflection of light by the Sun. This was attempted by the Kodaikanal Observatory in India during the conjunction of Regulus with the Sun in daylight on August 21st, 1917. The observation was attempted at the urging of the amateur German-British astronomer A. F. Lindemann, with his son, F. A. Lindemann, a well-known physicist, who later played a significant role as Churchill's science advisor during World War II. A century later Regulus will once again be in conjunction with the Sun, but by a remarkable coincidence, this will occur during a solar eclipse! Efforts will be made to measure the star deflection during the eclipse and the experiment is contrasted with the famous expeditions of 1919 which were the first to actually measure the light deflection, since the 1917 effort did not meet with success. Although in recent decades there have been efforts made to suggest that the 1919 eclipse team, led by Arthur Stanley Eddington and Sir Frank Watson Dyson, over-interpreted their results in favor of Einstein this talk will argue that such claims are wrong-headed. A close study of their data analysis reveals that they had good grounds for the decisions they made and this conclusion is reinforced by comparison with a modern re-analysis of the plates by the Greenwich Observatory conducted in 1977.

  2. Spin Rate and Deflection Ratio of a Ping Pong Ball

    Directory of Open Access Journals (Sweden)

    Byung Joon Ahn

    2013-01-01

    Full Text Available To investigate the effects of a spherical object’s spin rate on the curvature of its flight, Ping Pong balls, of varying spin rates, were hit horizontally and recorded from above with a high-speed camera. It was shown that there was a proportional relationship between the ball’s spin rate and deflection ratio. Additionally, using the results of the analyzed data, a coefficient of skin friction of the Ping Pong ball was found to be approximately 0.2 under the specific conditions of this investigation.

  3. Online Estimation of wind turbine blade deflection with UWB signals

    DEFF Research Database (Denmark)

    Jensen, Tobias Lindstrøm; Jakobsen, Morten Lomholt; Østergaard, Jan;

    2015-01-01

    In this paper we use ultra-wideband (UWB) signals for the localization of blade tips on wind turbines. Our approach is to acquire two separate distances to each tip via time-delay estimation, and each tip is then localized by triangulation. We derive an approximate maximum a posteriori (MAP) delay...... estimator exploiting i) contextual prior information and ii) a direct-path approximation. The resulting deflection estimation algorithm is computationally feasible for online usage. Simulation studies are conducted to assess the overall triangulation uncertainty and it is observed that negative correlation...

  4. Direct measurement of Vorticella contraction force by micropipette deflection.

    Science.gov (United States)

    France, Danielle; Tejada, Jonathan; Matsudaira, Paul

    2017-02-01

    The ciliated protozoan Vorticella convallaria is noted for its exceptionally fast adenosine triphosphate-independent cellular contraction, but direct measurements of contractile force have proven difficult given the length scale, speed, and forces involved. We used high-speed video microscopy to image live Vorticella stalled in midcontraction by deflection of an attached micropipette. Stall forces correlate with both distance contracted and the resting stalk length. Estimated isometric forces range from 95 to 177 nanonewtons (nN), or 1.12 nN·μm(-1) of the stalk. Maximum velocity and work are also proportional to distance contracted. These parameters constrain proposed biochemical/physical models of the contractile mechanism.

  5. Angular Dispersion and Deflection Function for Heavy Ion Elastic Scattering

    Institute of Scientific and Technical Information of China (English)

    BAI Zhen; MAO Rui-Shi; YUAN Xiao-Hua; Xu Zhi-Guo; ZHANG Hong-Bin; XU Hua-Gen; QI Hui-Rong; WANG Yue; JIA Fei; WU Li-Jie; DING Xian-Li; WANG Qi; GAO Qi; GAO Hui; LI Song-Lin; LI Jun-Qing; ZHANG Ya-Peng; XIAO Guo-Qing; JIN Gen-Ming; REN Zhong-Zhou; ZHOU Shan-Gui; XU Wang; HAN Jian-Long; Fan Gong-Tao; ZHANG Shuang-Quan; PANG Dan-Yang; SERGEY Yu-Kun; XIAO Zhi-Gang; XU Hu-Shan; SUN Zhi-Yu; HU Zheng-Guo; ZHANG Xue-Ying; WANG Hong-Wei

    2007-01-01

    The differential cross sections for elastic scattering products of17 F on 208 Pb have been measured.The angular dispersion plots of In(dσ/dθ)versus θ2 are obtained from the angular distribution of the elastic scattering differential cross sections.Systematical analysis on the angular dispersion for the available experimental data indicates that there is an angular dispersion turning angle at forward angular range within the grazing angle.This turning angle can be clarified as nuclear rainbow in classical deflection function.The exotic behaviour of the nuclear rainbow angle offers a new probe to investigate the halo and skin phenomena.

  6. The Deflection of Charged Particles in an Electric Dodecapole Field

    Energy Technology Data Exchange (ETDEWEB)

    Seely, D. G.; Chalut, K.; Thompson, J. S.; Kvale, T. J.

    1997-10-10

    The properties of an ion-optical device consisting of twelve long parallel rods placed equidistantly on a circle are briefly reviewed. The use of this device in its dodecapole configuration to deflect ions in a plane perpendicular to the axis of the dodecapole is discussed. Results of trajectory computations made with the SIMION ion-optics computer program demonstrate that the device works remarkably well in separating the constituents of a multiply-charged ion beam. The use of this device to merge an ion beam with an optical beam is proposed.

  7. Wind Turbine Blade Deflection Sensing System Based on UWB Technology

    DEFF Research Database (Denmark)

    Franek, Ondrej; Zhang, Shuai; Jensen, Tobias Lindstrøm

    2016-01-01

    by triangulation. An experimental setup with corner reflector antenna mounted at the tip and horn antennas at the root of a 37.3 m long blade is described. Analyzing the data from the experiment, special attention is given to the propagation aspects of the UWB links, with focus on the multipath effects caused...... by the blade. It is demonstrated that despite the adverse effects of the multipath propagation the ranging accuracy of the system amounts to 1.5 cm, leading to maximum error of deflection 4.5 %....

  8. Observation of Femtosecond Bunch Length Using a Transverse Deflecting Structure

    Energy Technology Data Exchange (ETDEWEB)

    Huning, M.; Bolzmann, A.; Schlarb, H.; /DESY; Frisch, J.; McCormick, D.; Ross, M.; Smith, T.; /SLAC; Rossbach, J.; /Hamburg U.

    2005-12-14

    The design of the VUV-FEL at DESY demands bunch lengths in the order of 50 fs and below. For the diagnostic of such very short bunches a transverse deflecting RF structure (LOLA) has been installed which streaks the beam according to the longitudinal distribution. Tests in the VUV-FEL yielded a rich substructure of the bunches. The most pronounced peak in the has a rms length of approximately 50 fs during FEL operation and below 20 fs FWHM at maximum compression. Depending on the transverse focusing a resolution well below 50 fs was achieved.

  9. THE HELIOCENTRIC DISTANCE WHERE THE DEFLECTIONS AND ROTATIONS OF SOLAR CORONAL MASS EJECTIONS OCCUR

    Energy Technology Data Exchange (ETDEWEB)

    Kay, C.; Opher, M., E-mail: ckay@bu.edu [Astronomy Department, Boston University, Boston, MA 02215 (United States)

    2015-10-01

    Understanding the trajectory of a coronal mass ejection (CME), including any deflection from a radial path, and the orientation of its magnetic field is essential for space weather predictions. Kay et al. developed a model, Forecasting a CME’s Altered Trajectory (ForeCAT), of CME deflections and rotation due to magnetic forces, not including the effects of reconnection. ForeCAT is able to reproduce the deflection of observed CMEs. The deflecting CMEs tend to show a rapid increase of their angular momentum close to the Sun, followed by little to no increase at farther distances. Here we quantify the distance at which the CME deflection is “determined,” which we define as the distance after which the background solar wind has negligible influence on the total deflection. We consider a wide range in CME masses and radial speeds and determine that the deflection and rotation of these CMEs can be well-described by assuming they propagate with constant angular momentum beyond 10 R{sub ⊙}. The assumption of constant angular momentum beyond 10 R{sub ⊙} yields underestimates of the total deflection at 1 AU of only 1%–5% and underestimates of the rotation of 10%. Since the deflection from magnetic forces is determined by 10 R{sub ⊙}, non-magnetic forces must be responsible for any observed interplanetary deflections or rotations where the CME has increasing angular momentum.

  10. Deflection of resilient materials for reduction of floor impact sound.

    Science.gov (United States)

    Lee, Jung-Yoon; Kim, Jong-Mun

    2014-01-01

    Recently, many residents living in apartment buildings in Korea have been bothered by noise coming from the houses above. In order to reduce noise pollution, communities are increasingly imposing bylaws, including the limitation of floor impact sound, minimum thickness of floors, and floor soundproofing solutions. This research effort focused specifically on the deflection of resilient materials in the floor sound insulation systems of apartment houses. The experimental program involved conducting twenty-seven material tests and ten sound insulation floating concrete floor specimens. Two main parameters were considered in the experimental investigation: the seven types of resilient materials and the location of the loading point. The structural behavior of sound insulation floor floating was predicted using the Winkler method. The experimental and analytical results indicated that the cracking strength of the floating concrete floor significantly increased with increasing the tangent modulus of resilient material. The deflection of the floating concrete floor loaded at the side of the specimen was much greater than that of the floating concrete floor loaded at the center of the specimen. The Winkler model considering the effect of modulus of resilient materials was able to accurately predict the cracking strength of the floating concrete floor.

  11. UHECR correlations taking account of composition and Galactic magnetic deflections

    CERN Document Server

    Roberts, J

    2013-01-01

    We predict the arrival direction distribution of cosmic rays including their deflection in the Galactic magnetic field, for several combinations of source and composition hypotheses: the sources are hard X-ray AGNs or uniformly sample the matter distribution of galaxies, and the composition at the source is pure proton or is the Galactic cosmic ray composition measured by CREAM. We use the regular component of the Jansson-Farrar 2012 model for the GMF and allow for rigidities as low as 2 EeV. We report the correlations of published UHECRs, rescaling event energies so as to reconcile the spectra of the different experiments and taking the overall energy uncertainty into account; different composition hypotheses are considered. This work demonstrates the feasibility of calculating GMF deflections to low enough rigidities to allow for heavy composition in correlation studies, and that non-trivial arrival direction structure should be expected even for mixed or heavy composition, as long as UHECRs come from the l...

  12. Large deflection of flexible tapered functionally graded beam

    Institute of Scientific and Technical Information of China (English)

    A.R.Davoodinik; G.H.Rahimi

    2011-01-01

    In this paper the semi-analytical analyses of the flexible cantilever tapered functionally graded beam under combined inclined end loading and intermediate loading are studied.In order to derive the fully non-linear equations governing the non-linear deformation,a curvilinear coordinate system is introduced.A general non-linear second order differential equation that governs the shape of a deflected beam is derived based on the geometric nonlinearities,infinitesimal local displacements and local rotation concepts with remarkable physical properties of functionally graded materials.The solutions obtained from semi-analytical methods are numerically compared with the existing elliptic integral solution for the case of a flexible uniform cantilever functionally graded beam.The effects of taper ratio,inclined end load angle and material property gradient on large deflection of the beam are evaluated.The Adomian decomposition method will be useful toward the design of tapered functionally graded compliant mechanisms driven by smart actuators.

  13. Design and Field Test of a Galvanometer Deflected Streak Camera

    Energy Technology Data Exchange (ETDEWEB)

    Lai, C C; Goosman, D R; Wade, J T; Avara, R

    2002-11-08

    We have developed a compact fieldable optically-deflected streak camera first reported in the 20th HSPP Congress. Using a triggerable galvanometer that scans the optical signal, the imaging and streaking function is an all-optical process without incurring any photon-electron-photon conversion or photoelectronic deflection. As such, the achievable imaging quality is limited mainly only by optical design, rather than by multiple conversions of signal carrier and high voltage electron-optics effect. All core elements of the camera are packaged into a 12 inch x 24 inch footprint box, a size similar to that of a conventional electronic streak camera. At LLNL's Site-300 Test Site, we have conducted a Fabry-Perot interferometer measurement of fast object velocity using this all-optical camera side-by-side with an intensified electronic streak camera. These two cameras are configured as two independent instruments for recording synchronously each branch of the 50/50 splits from one incoming signal. Given the same signal characteristics, the test result has undisputedly demonstrated superior imaging performance for the all-optical streak camera. It produces higher signal sensitivity, wider linear dynamic range, better spatial contrast, finer temporal resolution, and larger data capacity as compared with that of the electronic counterpart. The camera had also demonstrated its structural robustness and functional consistence to be well compatible with field environment. This paper presents the camera design and the test results in both pictorial records and post-process graphic summaries.

  14. Deflection of Resilient Materials for Reduction of Floor Impact Sound

    Directory of Open Access Journals (Sweden)

    Jung-Yoon Lee

    2014-01-01

    Full Text Available Recently, many residents living in apartment buildings in Korea have been bothered by noise coming from the houses above. In order to reduce noise pollution, communities are increasingly imposing bylaws, including the limitation of floor impact sound, minimum thickness of floors, and floor soundproofing solutions. This research effort focused specifically on the deflection of resilient materials in the floor sound insulation systems of apartment houses. The experimental program involved conducting twenty-seven material tests and ten sound insulation floating concrete floor specimens. Two main parameters were considered in the experimental investigation: the seven types of resilient materials and the location of the loading point. The structural behavior of sound insulation floor floating was predicted using the Winkler method. The experimental and analytical results indicated that the cracking strength of the floating concrete floor significantly increased with increasing the tangent modulus of resilient material. The deflection of the floating concrete floor loaded at the side of the specimen was much greater than that of the floating concrete floor loaded at the center of the specimen. The Winkler model considering the effect of modulus of resilient materials was able to accurately predict the cracking strength of the floating concrete floor.

  15. System for deflection measurements of floating dry docks

    Science.gov (United States)

    Gorbachev, Alexey A.; Pantyushin, Anton V.; Serikova, Mariya G.; Korotaev, Valery V.; Timofeev, Aleksandr N.

    2015-05-01

    In this paper we introduce a system for deflection measurement of floating dry docks. The system contains two measurement channels observing opposite directions of the dock. It also includes set of reference marks, an industrial computer and a display. Each channel contains CMOS camera with long focal-length lens. Reference marks are implemented as IR LED arrays with 940 nm working wavelength for better performance within bad weather conditions (e.g. fog, rain, high humidity etc.). In the paper we demonstrate results of an analysis of different optical schemes for coupling the oppositely directed channels of the measurement unit and show that the scheme with two image sensors with separated lenses is an optimal option, because it allows usage of nonequidistant location of reference marks and demonstrates the least value of parasitic shift caused by rotations of the measuring unit. The developed system was tested both on specially-designed setup and in real infrastructure of a floating dry dock. The conducted tests proved that a measuring error of the system is smaller than +/- 1.5 mm within the measurement range of +/- 150 mm when deflection of 100 m dock is measured. Obtained results showed that the system demonstrates an ability to work in a harsh environment including poor weather conditions.

  16. Determination of the Critical Value of Deflection for Embedded Cylindrical Structures

    Institute of Scientific and Technical Information of China (English)

    LIU Jian-qi; CHEN Bin; WANG Hai-yan

    2005-01-01

    An embedded cylinder is a large-diameter cylinder embedded in a soil foundation. The state of failure of such an embedded cylindrical structure shows large deflection instead of slide and overturn of the traditional gravity type of structure placed on a rubble base or foundation base. The critical value of deflection of the embedded cylindrical structure, which is the maximum allowable deflection for stability calculation of the cylinder, is a vital control value. Through investigation on deflection and soil pressures on an embedded cylinder by model experiments, the variations of the angle of rotation θ of a cylinder with effective anti-overturning ratio η and moment MH of thrust are discussed. On the basis of experimental study, the critical value of deflection of the cylindrical structure is proposed in the paper. Meanwhile, the formulas for calculating deflection of cylinders are derived.

  17. Deflection routing in slotted self-routing networks with arbitrary topology

    OpenAIRE

    2002-01-01

    A deflection routing algorithm that can be applied to a novel self-routing address scheme for networks with arbitrary topology is proposed. The proposed deflection routing algorithm can be implemented all-optically using bitwise optical logic gates. Besides the primary output link selection, alternate output link choices by a packet at each node in case of deflection are also encoded in the address header. Priority classes can also be defined in the proposed address scheme. The performance of...

  18. Global Trends of CME Deflections Based on CME and Solar Parameters

    CERN Document Server

    Kay, C; Evans, R M

    2014-01-01

    Accurate space weather forecasting requires knowledge of the trajectory of coronal mass ejections (CMEs), including any deflections close to the Sun or through interplanetary space. Kay et al. 2013 introduced ForeCAT, a model of CME deflection resulting from the background solar magnetic field. For a magnetic field solution corresponding to Carrington Rotation (CR) 2029 (declining phase, April-May 2005), the majority of the CMEs deflected to the Heliospheric Current Sheet (HCS), the minimum in magnetic pressure on global scales. Most of the deflection occurred below 4 Rs. Here we extend ForeCAT to include a three dimensional description of the deflecting CME. We attempt to answer the following questions: a) Do all CMEs deflect to the magnetic minimum? and b) Does most deflection occur within the first few solar radii (~4 Rs)? Results for solar minimum and declining phase CMEs show that not every CME deflects to the magnetic minimum and that typically about half of the deflection occurs below 10 Rs. Slow, narr...

  19. Mission Analysis For the Ion Beam Deflection of Fictitious Asteroid 2015PDC

    CERN Document Server

    Bombardelli, Claudio; Cano, Juan Luis

    2015-01-01

    A realistic mission scenario for the deflection of fictitious asteroid 2015PDC is investigated that makes use of the ion beam shepherd concept as primary deflection technique. The article deals with the design of a low thrust rendezvous trajectory to the asteroid, the estimation of the propagated covariance ellipsoid and the outcome of a slow-push deflection starting from three worst case scenarios (impacts in New Delhi, Dhaka and Teheran). Displacing the impact point towards very low populated areas, as opposed to full deflection, is found to be the simplest and most effective mitigation approach. Mission design, technical and political aspects are discussed.

  20. UWB Wind Turbine Blade Deflection Sensing for Wind Energy Cost Reduction

    DEFF Research Database (Denmark)

    Zhang, Shuai; Jensen, Tobias Lindstrøm; Franek, Ondrej

    2015-01-01

    A new application of utilizing ultra-wideband (UWB) technology to sense wind turbine blade deflections is introduced in this paper for wind energy cost reduction. The lower UWB band of 3.1–5.3 GHz is applied. On each blade, there will be one UWB blade deflection sensing system, which consists...... is always of sufficient quality for accurate estimations under different deflections. The measured results reveal that the blade tip-root distance and blade deflection can be accurately estimated in the complicated and lossy wireless channels around a wind turbine blade. Some future research topics...

  1. BRIEF REPORT: Photon deflection by a Coulomb field in noncommutative QED

    Science.gov (United States)

    Pires, C. A. de S.

    2004-12-01

    In noncommutative QED photons present self-interactions in the form of triple and quartic interactions. The triple interaction implies that, even though the photon is electrically neutral, it will deflect when in the presence of an electromagnetic field. If detected, such deflection would be undoubted evidence of noncommutative space-time. In this work we derive a general expression for the deflection of a photon by any electromagnetic field. As an application we consider the case of the deflection of a photon by an external static Coulomb field.

  2. Quantum Effects on the Deflection of Light and the Gauss-Bonnet Theorem

    CERN Document Server

    Jusufi, Kimet

    2016-01-01

    In this letter we apply the Gauss--Bonnet theorem to calculate the deflection angle by a quantum corrected Schwarzschild black hole in the weak limit approximation. In particular, we calculate the light deflection by two types of quantum corrected black holes: the renormalization group improved Schwarzschild solution and the quantum corrected Schwarzschild solution in Bohmian quantum mechanics. We start from the corresponding optical metrics to use then the Gauss--Bonnet theorem and calculate the Gaussian curvature in both cases. Finally, we calculate the leading terms of the deflection angle and show that quantum corrections modifies the deflection angle in both solutions.

  3. Orthogonally interdigitated shielded serpentine travelling wave cathode ray tube deflection structure

    Science.gov (United States)

    Hagen, Edward C.; Hudson, Charles L.

    1995-01-01

    A new deflection structure (12) which deflects a beam of charged particles, uch as an electron beam (15), includes a serpentine set (20) for transmitting a deflection field, and a shielding frame (25) for housing the serpentine set (20). The serpentine set (20) includes a vertical serpentine deflection element (22) and a horizontal serpentine deflection element (24). These deflection elements (22, 24) are identical, and are interdigitatedly and orthogonally disposed relative to each other, for forming a central transmission passage (75), through which the electron beam (15) passes, and is deflected by the deflection field, so as to minimize drift space signal distortion. The shielding frame (25) includes a plurality of ground blocks (26, 28, 30, 32), and forms an internal serpentine trough (77) within these ground blocks, for housing the serpentine set (20). The deflection structure (12) further includes a plurality of feedthrough connectors (35, 37, 35I, 37I), which are inserted through the shielding frame (25), and which are electrically connected to the serpentine set (20).

  4. Periodic Relativity: Deflection of Light, Acceleration, Rotation Curves

    Directory of Open Access Journals (Sweden)

    Zaveri V. H.

    2015-01-01

    Full Text Available Vectorial analysis relating to derivation of deflection of light is presented. Curvilinear acceleration is distinguished from the Newtonian polar conic acceleration. The dif- ference between the two is due to the curvature term. Lorentz invariant expression for acceleration is derived. A physical theory of rotation curves of galaxies based on second solution to Einstein’s field equation is presented. Theory is applied to Milky Way, M31, NGC3198 and Solar system. Modified Kepler’s third law yields correct orbital periods of stars in a galaxy. Deviation factor in the line element of t he theory happens to be the ratio of the Newtonian gravitational acceleration to th e measured acceleration of the star in the galaxy. Therefore this deviation factor can replace the MOND function.

  5. Self-contained instrument for measuring subterranean tunnel wall deflection

    Science.gov (United States)

    Rasmussen, Donald Edgar; Hof, Jr., Peter John

    1978-01-01

    The deflection of a subterranean tunnel is measured with a rod-like, self-contained instrument that is adapted to be inserted into a radially extending bore of the tunnel adjacent an end of the tunnel where the tunnel is being dug. One end of the instrument is anchored at the end of the bore remote from the tunnel wall, while the other end of the intrument is anchored adjacent the end of the wall in proximity to the tunnel wall. The two ends of the instrument are linearly displaceable relative to each other; the displacement is measured by a transducer means mounted on the instrument. Included in the instrument is a data storage means including a paper tape recorder periodically responsive to a parallel binary signal indicative of the measured displacement.

  6. Asteroid Deflection Using a Spacecraft in Restricted Keplerian Motion

    CERN Document Server

    Ketema, Yohannes

    2016-01-01

    A method for asteroid deflection that makes use of a spacecraft moving back and forth on a segment of an appropriate Keplerian orbit about the asteroid is described and evaluated. It is shown that, on average, the spacecraft describing such a trajectory can exert a significantly larger force on the asteroid than e.g. a stationary gravity tractor, thereby reducing the time needed to effect a desired velocity change for the asteroid. Furthermore, the current method does not require canted thrusters on the spacecraft (unlike a stationary gravity tractor), markedly reducing the amount of fuel needed to create a given change in the asteroid velocity. In addition, the method allows for the simultaneous use of several spacecraft, further strengthening the overall tugging effect on the asteroid, and distributing the thrust requirement among the spacecraft.

  7. Fabrication and Testing of Deflecting Cavities for APS

    Energy Technology Data Exchange (ETDEWEB)

    Mammosser, John; Wang, Haipeng; Rimmer, Robert; Jim, Henry; Katherine, Wilson; Dhakal, Pashupati; Ali, Nassiri; Jim, Kerby; Jeremiah, Holzbauer; Genfa, Wu; Joel, Fuerst; Yawei, Yang; Zenghai, Li

    2013-09-01

    Jefferson Lab (Newport News, Virginia) in collaboration with Argonne National Laboratory (Argonne, IL) has fabricated and tested four first article, 2.8 GHz, deflecting SRF cavities, for Argonne's Short-Pulse X-ray (SPX) project. These cavities are unique in many ways including the fabrication techniques in which the cavity cell and waveguides were fabricated. These cavity subcomponents were milled from bulk large grain niobium ingot material directly from 3D CAD files. No forming of sub components was used with the exception of the beam-pipes. The challenging cavity and helium vessel design and fabrication results from the stringent RF performance requirements required by the project and operation in the APS ring. Production challenges and fabrication techniques as well as testing results will be discussed in this paper.

  8. Study of surface charges in ballistic deflection transistors

    Science.gov (United States)

    Millithaler, J.-F.; Iñiguez-de-la-Torre, I.; Mateos, J.; GonzáIez, T.; Margala, M.

    2015-12-01

    This paper presents a comprehensive study of the behavior of surface charges in ballistic deflection transistors, at room temperature, where the in-plane geometry associating two drains with two gates in push-pull modes allows the control of electron path. Monte Carlo simulations were performed and compared with experimental data by using different models for accounting for surface charge effects. The simple model which assumes a constant and uniform value of the surface charge provides good results at equilibrium, but it is not able to correctly reproduce the BDT’s complex behavior when biased. We have confirmed that for a correct description of the device operation it is necessary to use a model allowing the surface charge to adapt itself locally to the carrier concentration in its surroundings.

  9. Profiling compact toroid plasma density on CTIX with laser deflection

    Science.gov (United States)

    Brockington, Samuel Joseph Erwin

    A laser deflectometer measures line-integrated plasma density gradient using laser diodes and amplified point detectors. A laser passing through an optically thin plasma is refracted by an amount proportional to the line-integrated electron density gradient. I have designed, installed, and operated a deflection diagnostic for the Compact Toroid Injection Experiment (CTIX), a plasma rail gun which can create compact toroid (CT) plasmas of controllable density and velocity. The diagnostic design and motivation are discussed, as well as three experiments performed with deflectometry. Thus, my thesis consists of the design of the deflectometer diagnostic, a comparison of its accuracy to interferometer density measurements, and finally a survey of compact toroid density profiles in two dimensions conducted with an array of detectors.

  10. Plumb line deflection varied with time obtained by repeated gravimetry

    Institute of Scientific and Technical Information of China (English)

    李辉; 付广裕; 李正心

    2001-01-01

    In this paper, the plumb line deflection varied with time (PLV) are calculated with the Vening-Meinesz formula for Xiaguan and Beijing point based on the 28 and 39 campaigns of gravimetry at the local gravity networks in the Western Yunnan Earthquake Prediction Experiment Area and the North China, respectively. Based on the results, we conclude that: ① the maximum of PLV is under 0.12 and amplitudes of interannual variation are under 0.022.②PLV can be determined with the reliability of 0.012 by the modeling based on the precession of repeated gravimetry. This implies that repeated gravimetry could be used to determine the PLV. ③There exist some common and different characteristics for the different places and different components. It may provide a new approach for the study on the local or global geodynamic by using repeated gravimetry.

  11. Theory of using magnetic deflections to combine charged particle beams

    Energy Technology Data Exchange (ETDEWEB)

    Steckbeck, Mackenzie K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Doyle, Barney Lee [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-09-01

    Several radiation effects projects in the Ion Beam Lab (IBL) have recently required two disparate charged particle beams to simultaneously strike a single sample through a single port of the target chamber. Because these beams have vastly different mass–energy products (MEP), the low-MEP beam requires a large angle of deflection toward the sample by a bending electromagnet. A second electromagnet located further upstream provides a means to compensate for the small angle deflection experienced by the high-MEP beam during its path through the bending magnet. This paper derives the equations used to select the magnetic fields required by these two magnets to achieve uniting both beams at the target sample. A simple result was obtained when the separation of the two magnets was equivalent to the distance from the bending magnet to the sample, and the equation is given by: Bs= 1/2(rc/rs) Bc, where Bs and Bc are the magnetic fields in the steering and bending magnet and rc/rs is the ratio of the radii of the bending magnet to that of the steering magnet. This result is not dependent upon the parameters of the high MEP beam, i.e. energy, mass, charge state. Therefore, once the field of the bending magnet is set for the low-MEP beam, and the field in the steering magnet is set as indicted in the equation, the trajectory path of any high-MEP beam will be directed into the sample.

  12. A systematic analysis of the influence of the surrounding media in the photothermal beam deflection signal

    Energy Technology Data Exchange (ETDEWEB)

    Goeren, A; Prior, P; Macedo, F, E-mail: fmacedo@fisica.uminho.p [Physics Department, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal)

    2010-03-01

    The photothermal beam deflection (PDS) technique was tested for low thermal diffusivity materials. The effect of using different liquids as surrounding media was studied in a systematic way. The fundamental experimental parameters, like the pump beam power and the modulation frequency were also studied in order to find out the best combination that still allows us to get good signals. Due to the complexity of the optical alignment required, the usual mirage setup was adapted in order to allow the decoupling of the alignment of the cell containing the liquid and the sample holder. Simple, straightforward methods (like e.g. the phase method) were used for the thermal diffusivity determination of solids once the thermal diffusivity of the liquids used is always much lower than that of solids. The obtained values for the thermal diffusivity of test samples allow us to conclude that besides being possible to use any of the studied liquids as surrounding medium, ethanol is clearly the best choice, avoiding health problems related to CCl{sub 4}, which is the standard choice for PDS and PDS spectroscopy experiments, and technical/physical problems related to water and acetone. Modulation frequencies around 8 Hz combined with a pump beam power below 15 mW were proved to be the ideal conditions for this kind of experiment. The very low pump beam power required is also an important issue when talking about non-destructive analysis.

  13. Exploring the Spatial Resolution of the Photothermal Beam Deflection Technique in the Infrared Region

    CERN Document Server

    Seidel, Wolfgang

    2004-01-01

    In photothermal beam deflection spectroscopy (PTBD) generating and detection of thermal waves occur generally in the sub-millimeter length scale. Therefore, PTBD provides spatial information about the surface of the sample and permits imaging and/or microspectrometry. Recent results of PTBD experiments are presented with a high spatial resolution which is near the diffraction limit of the infrared pump beam (CLIO-FEL). We investigated germanium substrates showing restricted O+-doped regions with an infrared absorption line at a wavelength around 11.6 microns. The spatial resolution was obtained by strongly focusing the probe beam (i.e. a HeNe laser) on a sufficiently small spot. The strong divergence makes it necessary to refocus the probe beam in front of the position detector. The influence of the focusing elements on spatial resolution and signal-to-noise ratio is discussed. In future studies we expect an enhanced spatial resolution due to an extreme focusing of the probe beam leading to a highly sensitive...

  14. Arc Deflection Length Affected by Transverse Rotating Magnetic Field with Lateral Gas

    Science.gov (United States)

    Shiino, Toru; Ishii, Yoko; Yamamoto, Shinji; Iwao, Toru; High Current Energy Laboratory (HiCEL) Team

    2016-10-01

    Gas metal arc welding using shielding gas is often used in the welding industry. However, the arc deflection affected by lateral gas is problem because of inappropriate heat transfer. Shielding gas is used in order to prevent the instability affected by the arc deflection. However, the shielding gas causes turbulence, then blowhole of weld defect occurs because the arc affected by the instability is contaminated by the air. Thus, the magnetic field is applied to the arc in order to stabilize the arc using low amount of shielding gas. The method of applying the transverse rotating magnetic field (RMF) to the arc is one of the methods to prevent the arc instability. The RMF drives the arc because of electromagnetic force. The driven arc is considered to be prevented to arc deflection of lateral gas because the arc is restrained by the magnetic field because of the driven arc. In addition, it is assume the RMF prevented to the arc deflection of lateral gas from the multiple directions. In this paper, the arc deflection length affected by the RMF with lateral gas was elucidated in order to know the effect of the RMF for arc stabilization. Specifically, the arc deflection length affected by the magnetic frequency and the magnetic flux density is measured by high speed video camera. As a result, the arc deflection length decreases with increasing magnetic frequency, and the arc deflection length increases with increasing the magnetic flux density.

  15. Evaluation of disparate laser beam deflection technologies by means of number and rate of resolvable spots.

    Science.gov (United States)

    Bechtold, Peter; Hohenstein, Ralph; Schmidt, Michael

    2013-08-15

    We introduce a method to objectively evaluate systems of differing beam deflection technologies that commonly are described by disparate technical specifications. Using our new approach based on resolvable spots we will compare commercially available random-access beam deflection technologies, namely galvanometer scanners, piezo scanners, MEMS scanners, acousto-optic deflectors, and electro-optic deflectors.

  16. Short-term and long-term deflection of reinforced hollow core ...

    African Journals Online (AJOL)

    Short-term and long-term deflection of reinforced hollow core concrete slab systems. ... AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search ... For the prediction of the long-term deflection, a measured ratio of long-term ...

  17. A nonlinear mathematical model for large deflection of incompressible saturated poroelastic beams

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Nonlinear governing equations are established for large deflection of incompressible fluid saturated poroelastic beams under constraint that diffusion of the pore fluid is only in the axial direction of the deformed beams. Then, the nonlinear bending of a saturated poroelastic cantilever beam with fixed end impermeable and free end permeable, subjected to a suddenly applied constant concentrated transverse load at its free end, is examined with the Galerkin truncation method. The curves of deflections and bending moments of the beam skeleton and the equivalent couples of the pore fluid pressure are shown in figures. The results of the large deflection and the small deflection theories of the cantilever poroelastic beam are compared, and the differences between them are revealed. It is shown that the results of the large deflection theory are less than those of the corresponding small deflection theory, and the times needed to approach its stationary states for the large deflection theory are much less than those of the small deflection theory.

  18. A small-gap electrostatic micro-actuator for large deflections.

    Science.gov (United States)

    Conrad, Holger; Schenk, Harald; Kaiser, Bert; Langa, Sergiu; Gaudet, Matthieu; Schimmanz, Klaus; Stolz, Michael; Lenz, Miriam

    2015-12-11

    Common quasi-static electrostatic micro actuators have significant limitations in deflection due to electrode separation and unstable drive regions. State-of-the-art electrostatic actuators achieve maximum deflections of approximately one third of the electrode separation. Large electrode separation and high driving voltages are normally required to achieve large actuator movements. Here we report on an electrostatic actuator class, fabricated in a CMOS-compatible process, which allows high deflections with small electrode separation. The concept presented makes the huge electrostatic forces within nanometre small electrode separation accessible for large deflections. Electrostatic actuations that are larger than the electrode separation were measured. An analytical theory is compared with measurement and simulation results and enables closer understanding of these actuators. The scaling behaviour discussed indicates significant future improvement on actuator deflection. The presented driving concept enables the investigation and development of novel micro systems with a high potential for improved device and system performance.

  19. Design Optimization of Deflection Caused After Release of Multilayer Structural Membrane of Symmetric Toggle Switch

    Directory of Open Access Journals (Sweden)

    K. Maninder

    2011-01-01

    Full Text Available This paper presents the optimization in deflection caused by the inbuilt stress generated in mechanical or movable membrane of Symmetric Toggle RF MEMS Switch (STS. The movable membrane of STS was initially fabricated with two different materials, i.e. Chrome and Gold. The simulated deflection at 70 °C was 11.9 µm, and experimental deflection was 11-12 µm. We present a study of inbuilt deflection reduction in multimetal movable layers without change in actuation voltage of the switch. The design study was initially carried out on cantilevers and then on structural membrane of STS. STS with proposed multilayer of Cr-Au-Au-Ti-Au has a simulated deflection of 0.56 µm at 70 °C.

  20. Four-dimensional visualization of a small-scale flame based on deflection tomography

    Science.gov (United States)

    Zhang, Bin; Liu, Zhigang; Zhao, Minmin

    2016-11-01

    Optical computed tomography is an important technique in the visualization and diagnosis of various flow fields. A small-scale diffusion flame was visualized using deflection tomography. A projection sampling system was proposed for deflection tomography to obtain deflectograms with a pair of gratings. Wave-front retrieval was employed for processing the deflectograms to obtain the deflection angles of the rays. This two-dimensional data extraction method expanded the application of deflection tomography and was suitable for the projection extraction of small-scale combustion. Deflection angle revision reconstruction algorithm was used to reconstruct the temperature distributions in 10 cross sections for each deflectogram in different instants. The flow structure was reconstructed using a visualization toolkit equipped with the marching cube and ray casting algorithms. The performed experiments demonstrated the three-dimensional dynamic visualization of temperature distributions and the flame structures of small-scale diffusion combustion.

  1. Experimental and Theoretical Deflections of Hybrid Composite Sandwich Panel under Four-point Bending Load

    Directory of Open Access Journals (Sweden)

    Jauhar Fajrin

    2017-03-01

    Full Text Available This paper presents a comparison of theoretical and experimental deflection of a hybrid sandwich panel under four-point bending load. The paper initially presents few basic equations developed under three-point load, followed by development of model under four-point bending load and a comparative analysis between theoretical and experimental results. It was found that the proposed model for predicting the deflection of hybrid sandwich panels provided fair agreement with the experimental values. Most of the sandwich panels showed theoretical deflection values higher than the experimental values, which is desirable in the design. It was also noticed that the introduction of intermediate layer does not contribute much to reduce the deflection of sandwich panel as the main contributor for the total deflection was the shear deformation of the core that mostly determined by the geometric of the samples and the thickness of the core.

  2. Improvements of the undulator spectral performance by compensating the backing beam deflection

    CERN Document Server

    Wang, C; Chang, L H; Chang, C H; Fan, T C; Bach, H; Blomqvist, I

    2002-01-01

    This study thoroughly examines how the backing beam deflection affects the undulator spectral performance. Reduction of the undulator spectral intensity owing to backing beam deflection is analytically evaluated based on plane-wave approximation. The results reveal that the amplitude and the slope of the backing beam deflection affect the undulator spectral performance. Provided is a novel figure-of-merit, rms of the regressed accumulated gap deviation, to determine the backing beam deflection budget. An example of a 3.9 m undulator supporting carriage mounted with 50-mm period length undulator magnet (U5) under a maximum magnetic loading of 5 metric tons at a minimum operating gap of 14 mm, is provided. Its mechanical features are first examined via 3D commercial finite element code ANSYS that concludes the backing beam deflection is influenced heavily by the rigidity of the undulator support frames. Examining the corresponding spectral performance shows that significantly diminishing the undulator spectral ...

  3. Numerical Simulation Study on the Surface Deflection of Cylindrical Shallow Shell

    Institute of Scientific and Technical Information of China (English)

    XING Zhongwen; BAO Jun; LIU Zhongyuan; YANG Yuying; SUN Zhenzhong

    2006-01-01

    The increasing applications of new materials such as high strength low alloy (HSAL) steels and aluminum alloy sheets have lead to greater focus on the surface deflections of auto body panels in the automobile industry in recent years. The finite element models of cylindrical shallow shell that can represent auto body panels are established. Numerical simulations of forming and unloading of cylindrical shallow shell are carried out. And a measurement and evaluation method of the surface deflection is introduced. The simulations of surface deflections with various blank holding forces (BHF) show great agreement with the experimental results. The influence laws of sheet thickness and material properties such as yield strength σs, strain-hardening exponent n, anisotropy parameter r and strength coefficient k on the surface deflection are achieved by simulations, which give a basic reference for controlling surface deflections.

  4. Directed Energy Deflection Laboratory Measurements of Asteroids and Space Debris

    Science.gov (United States)

    Brashears, T.; Lubin, P. M.

    2016-12-01

    We report on laboratory studies of the effectiveness of directed energy planetary and space defense as a part of the DE-STAR (Directed Energy System for Targeting of Asteroids and exploRation) program. DE-STAR [1][5][6] and DE-STARLITE [2][5][6] are directed energy "stand-off" and "stand-on" programs, respectively. These systems consist of a modular array of kilowatt-class lasers powered by photovoltaics, and are capable of heating a spot on the surface of an asteroid to the point of vaporization. Mass ejection, as a plume of evaporated material, creates a reactionary thrust capable of diverting the asteroid's orbit. In a series of papers, we have developed a theoretical basis and described numerical simulations for determining the thrust produced by material evaporating from the surface of an asteroid [1][2][3][4][5][6]. In the DE-STAR concept, the asteroid itself is used as the deflection "propellant". This study presents results of experiments designed to measure the thrust created by evaporation from a laser directed energy spot. We constructed a vacuum chamber to simulate space conditions, and installed a torsion balance that holds an "asteroid" or a space debris sample. The sample is illuminated with a fiber array laser with flux levels up to 60 MW/m2 which allows us to simulate a mission level flux but on a small scale. We use a separate laser as well as a position sensitive centroid detector to readout the angular motion of the torsion balance and can thus determine the thrust. We compare the measured thrust to the models. Our theoretical models indicate a coupling coefficient well in excess of 100 µN/Woptical, though we assume a more conservative value of 80 µN/Woptical and then degrade this with an optical "encircled energy" efficiency of 0.75 to 60 µN/Woptical in our deflection modeling. Our measurements discussed here yield about 60 µN/Wabsorbed as a reasonable lower limit to the thrust per optical watt absorbed.

  5. Directed energy deflection laboratory measurements of common space based targets

    Science.gov (United States)

    Brashears, Travis; Lubin, Philip; Hughes, Gary B.; Meinhold, Peter; Batliner, Payton; Motta, Caio; Madajian, Jonathan; Mercer, Whitaker; Knowles, Patrick

    2016-09-01

    We report on laboratory studies of the effectiveness of directed energy planetary defense as a part of the DE-STAR (Directed Energy System for Targeting of Asteroids and exploRation) program. DE-STAR and DE-STARLITE are directed energy "stand-off" and "stand-on" programs, respectively. These systems consist of a modular array of kilowatt-class lasers powered by photovoltaics, and are capable of heating a spot on the surface of an asteroid to the point of vaporization. Mass ejection, as a plume of evaporated material, creates a reactionary thrust capable of diverting the asteroid's orbit. In a series of papers, we have developed a theoretical basis and described numerical simulations for determining the thrust produced by material evaporating from the surface of an asteroid. In the DESTAR concept, the asteroid itself is used as the deflection "propellant". This study presents results of experiments designed to measure the thrust created by evaporation from a laser directed energy spot. We constructed a vacuum chamber to simulate space conditions, and installed a torsion balance that holds a common space target sample. The sample is illuminated with a fiber array laser with flux levels up to 60 MW/m2 , which allows us to simulate a mission level flux but on a small scale. We use a separate laser as well as a position sensitive centroid detector to readout the angular motion of the torsion balance and can thus determine the thrust. We compare the measured thrust to the models. Our theoretical models indicate a coupling coefficient well in excess of 100 μN/Woptical, though we assume a more conservative value of 80 μN/Woptical and then degrade this with an optical "encircled energy" efficiency of 0.75 to 60 μN/Woptical in our deflection modeling. Our measurements discussed here yield about 45 μN/Wabsorbed as a reasonable lower limit to the thrust per optical watt absorbed. Results vary depending on the material tested and are limited to measurements of 1 axis, so

  6. Comet deflection by directed energy: a finite element analysis

    Science.gov (United States)

    Madajian, Jonathan; Griswold, Janelle; Gandra, Anush; Hughes, Gary B.; Zhang, Qicheng; Rupert, Nic; Lubin, Philip

    2016-09-01

    Comets and Asteroids are viable threats to our planet; if these space rocks are smaller than 25 meters, they burn up in the atmosphere, but if they are wider than 25 meters they can cause damage to the impact area. Anything more than one to two kilometers can have worldwide effects, furthermore a mile-wide asteroid travelling at 30,000 miles per hour has the energy equal to a megaton bomb and is very likely to wipe out most of the life on Earth. Residents near Chelyabinsk, Russia experienced the detrimental effects of a collision with a Near-Earth Asteroid (NEA) on 15 February 2013 as a 20 m object penetrated the atmosphere above that city. The effective yield from this object was approximately 1/2 Megaton TNT equivalent (Mt), or that of a large strategic warhead. The 1908 Tunguska event, also over Russia, is estimated to have had a yield of approximately 15 Mt and had the potential to kill millions of people had it come down over a large city1. In the face of such danger a planetary defense system is necessary and this paper proposes a design for such a system. DE-STAR (Directed Energy System for Targeting of Asteroids and exploRation) is a phased array laser system that can be used to oblate, deflect and de-spin asteroids and comets.

  7. String formulation of space charge forces in a deflecting bunch

    Science.gov (United States)

    Talman, Richard

    2004-10-01

    The force between two moving point charges, because of its inverse square law singularity, cannot be applied directly in the numerical simulation of bunch dynamics; radiative effects make this especially true for short bunches being deflected by magnets. This paper describes a formalism circumventing this restriction in which the basic ingredient is the total force on a point charge comoving with a longitudinally aligned, uniformly charged string. Bunch evolution can then be treated using direct particle-to-particle, intrabeam scattering, with no need for an intermediate, particle-in-cell, step. Electric and magnetic fields do not appear individually in the theory. Since the basic formulas are both exact (in paraxial approximation) and fully relativistic, they are applicable to beams of all particle types and all energies. But the theory is expected to be especially useful for calculating the emittance growth of the ultrashort electron bunches of current interest for energy recovery linacs and free-electron lasers. The theory subsumes coherent synchrotron radiation and centrifugal space charge force. Renormalized, on-axis, longitudinal field components are in excellent agreement with values from Saldin et al. [DESY Report No. DESY-TESLA-FEL-96-14, 1995; Nucl. Instrum. Methods Phys. Res., Sect. ANIMAER0168-9002 417, 158 (1998).10.1016/S0168-9002(98)00623-8

  8. String formulation of space charge forces in a deflecting bunch

    Directory of Open Access Journals (Sweden)

    Richard Talman

    2004-10-01

    Full Text Available The force between two moving point charges, because of its inverse square law singularity, cannot be applied directly in the numerical simulation of bunch dynamics; radiative effects make this especially true for short bunches being deflected by magnets. This paper describes a formalism circumventing this restriction in which the basic ingredient is the total force on a point charge comoving with a longitudinally aligned, uniformly charged string. Bunch evolution can then be treated using direct particle-to-particle, intrabeam scattering, with no need for an intermediate, particle-in-cell, step. Electric and magnetic fields do not appear individually in the theory. Since the basic formulas are both exact (in paraxial approximation and fully relativistic, they are applicable to beams of all particle types and all energies. But the theory is expected to be especially useful for calculating the emittance growth of the ultrashort electron bunches of current interest for energy recovery linacs and free-electron lasers. The theory subsumes coherent synchrotron radiation and centrifugal space charge force. Renormalized, on-axis, longitudinal field components are in excellent agreement with values from Saldin et al. [DESY Report No. DESY-TESLA-FEL-96-14, 1995; Nucl. Instrum. Methods Phys. Res., Sect. A 417, 158 (1998.NIMAER0168-900210.1016/S0168-9002(9800623-8

  9. A simple damage detection indicator using operational deflection shapes

    Science.gov (United States)

    Sampaio, R. P. C.; Maia, N. M. M.; Almeida, R. A. B.; Urgueira, A. P. V.

    2016-05-01

    Catastrophic structural failure of aircrafts, bridges, buildings and other structures in modern societies has always been of primary concern because of the loss of human lifes and of negative economic impact. The aging of the structures, the growing dependency on their role in our networks of transportation, energy and comunications, the smaller construction tolerances, the bigger power demanded and the media and society awardness to catastrophic events are sufficient motivations for the growing field of structural health monitoring, which aims at assessing the actual condition of a structure and to identify incipient damage. Damage identification can be considered as a two step process, the detection and the diagnosis. The former, and fundamental step, is the confirmation of an efective damage existence. When the response is affirmative, the latter step begins with the diagnosis, and then the questions are: where?, how much?, what type?, when will it fail? In this paper the authors propose a simple method to detect and relatively quantify structural damage by using measured vibrations data, specifically the operational deflections shapes. Numerical simulations and experimental tests are presented to validate the proposed method.

  10. Moth tails divert bat attack: evolution of acoustic deflection.

    Science.gov (United States)

    Barber, Jesse R; Leavell, Brian C; Keener, Adam L; Breinholt, Jesse W; Chadwell, Brad A; McClure, Christopher J W; Hill, Geena M; Kawahara, Akito Y

    2015-03-03

    Adaptations to divert the attacks of visually guided predators have evolved repeatedly in animals. Using high-speed infrared videography, we show that luna moths (Actias luna) generate an acoustic diversion with spinning hindwing tails to deflect echolocating bat attacks away from their body and toward these nonessential appendages. We pit luna moths against big brown bats (Eptesicus fuscus) and demonstrate a survival advantage of ∼ 47% for moths with tails versus those that had their tails removed. The benefit of hindwing tails is equivalent to the advantage conferred to moths by bat-detecting ears. Moth tails lured bat attacks to these wing regions during 55% of interactions between bats and intact luna moths. We analyzed flight kinematics of moths with and without hindwing tails and suggest that tails have a minimal role in flight performance. Using a robust phylogeny, we find that long spatulate tails have independently evolved four times in saturniid moths, further supporting the selective advantage of this anti-bat strategy. Diversionary tactics are perhaps more common than appreciated in predator-prey interactions. Our finding suggests that focusing on the sensory ecologies of key predators will reveal such countermeasures in prey.

  11. GPS deflection monitoring of the West Gate Bridge

    Science.gov (United States)

    Raziq, Noor; Collier, Philip

    2007-05-01

    The achievable precision and relatively high sampling rates of currently available GPS receivers are well suited for monitoring the movements of long-span engineering structures where the amplitude of movements is often more than a few centimetres and the frequency of vibrations is low (below 10 Hz). However, engineering structures often offer non-ideal environments for GPS data collection due to high multipath interference and obstructions causing cycle slips in the GPS observations. Also, for many engineering structures such as bridge decks, vertical movements are more pronounced and more structurally critical than horizontal movements. Accuracy of GPS determined positions in the vertical direction is typically two to three times poorer than in the horizontal component. This paper describes the results of a GPS deflection monitoring trial on the West Gate Bridge in Melbourne, Australia. The results are compared to the estimated frequencies and movements from the design of the bridge and previous accelerometer campaigns. The frequency information derived from the GPS results is also compared to frequency data extracted from an accelerometer installed close to a GPS receiver. GPS results agree closely to the historical results and recent accelerometer trials for key modal frequencies. This indicates the suitability of GPS receivers to monitor engineering structures that exhibit smaller movements due to their stiffness and in environments not ideally suited to using GPS.

  12. Three-dimensional parabolic equation modeling of mesoscale eddy deflection.

    Science.gov (United States)

    Heaney, Kevin D; Campbell, Richard L

    2016-02-01

    The impact of mesoscale oceanography, including ocean fronts and eddies, on global scale low-frequency acoustics is examined using a fully three-dimensional parabolic equation model. The narrowband acoustic signal, for frequencies from 2 to 16 Hz, is simulated from a seismic event on the Kerguellen Plateau in the South Indian Ocean to an array of receivers south of Ascension Island in the South Atlantic, a distance of 9100 km. The path was chosen for its relevance to seismic detections from the HA10 Ascension Island station of the International Monitoring System, for its lack of bathymetric interaction, and for the dynamic oceanography encountered as the sound passes the Cape of Good Hope. The acoustic field was propagated through two years (1992 and 1993) of the eddy-permitting ocean state estimation ECCO2 (Estimating the Circulation and Climate of the Ocean, Phase II) system. The range of deflection of the back-azimuth was 1.8° with a root-mean-square of 0.34°. The refraction due to mesoscale oceanography could therefore have significant impacts upon localization of distant low-frequency sources, such as seismic or nuclear test events.

  13. Comparing deflection measurements of a magnetically steerable catheter using optical imaging and MRI

    Energy Technology Data Exchange (ETDEWEB)

    Lillaney, Prasheel, E-mail: Prasheel.Lillaney@ucsf.edu; Caton, Curtis; Martin, Alastair J.; Losey, Aaron D.; Evans, Leland; Saeed, Maythem; Cooke, Daniel L.; Wilson, Mark W.; Hetts, Steven W. [Department of Radiology and Biomedical Imaging, University of California San Francisco, San Francisco, California 94143 (United States)

    2014-02-15

    Purpose: Magnetic resonance imaging (MRI) is an emerging modality for interventional radiology, giving clinicians another tool for minimally invasive image-guided interventional procedures. Difficulties associated with endovascular catheter navigation using MRI guidance led to the development of a magnetically steerable catheter. The focus of this study was to mechanically characterize deflections of two different prototypes of the magnetically steerable catheterin vitro to better understand their efficacy. Methods: A mathematical model for deflection of the magnetically steerable catheter is formulated based on the principle that at equilibrium the mechanical and magnetic torques are equal to each other. Furthermore, two different image based methods for empirically measuring the catheter deflection angle are presented. The first, referred to as the absolute tip method, measures the angle of the line that is tangential to the catheter tip. The second, referred to the base to tip method, is an approximation that is used when it is not possible to measure the angle of the tangent line. Optical images of the catheter deflection are analyzed using the absolute tip method to quantitatively validate the predicted deflections from the mathematical model. Optical images of the catheter deflection are also analyzed using the base to tip method to quantitatively determine the differences between the absolute tip and base to tip methods. Finally, the optical images are compared to MR images using the base to tip method to determine the accuracy of measuring the catheter deflection using MR. Results: The optical catheter deflection angles measured for both catheter prototypes using the absolute tip method fit very well to the mathematical model (R{sup 2} = 0.91 and 0.86 for each prototype, respectively). It was found that the angles measured using the base to tip method were consistently smaller than those measured using the absolute tip method. The deflection angles measured

  14. The Heliocentric Distance Where the Deflections and Rotations of Solar Coronal Mass Ejections Occur

    CERN Document Server

    Kay, C

    2015-01-01

    Understanding the trajectory of a coronal mass ejection (CME), including any deflection from a radial path, and the orientation of its magnetic field is essential for space weather predictions. Kay et al. (2015b) developed a model, Forecasting a CME's Altered Trajectory (ForeCAT), of CME deflections and rotation due to magnetic forces, not including the effects of reconnection. ForeCAT is able to reproduce the deflection of observed CMEs (Kay et al. 2015a). The deflecting CMEs tend to show a rapid increase of their angular momentum close to the Sun, followed by little to no increase at farther distances. Here we quantify the distance at which the CME deflection is "determined," which we define as the distance after which the background solar wind has negligible influence on the total deflection. We consider a wide range in CME masses and radial speeds and determine that the deflection and rotation of these CMEs can be well-described by assuming they propagate with constant angular momentum beyond 10 Rs. The a...

  15. Deflection determination of concrete structures considering nonlinearity based on long-gauge strain sensors

    Science.gov (United States)

    Hong, Wan; Lv, Kui; Li, Bing; Jiang, Yuchen; Hu, Xiamin; Qu, Qizhong

    2017-10-01

    Deflection determination of concrete structures using distributed long-gauge strain sensors is investigated in this paper. Firstly, the relationship between deflection and distributed long-gauge strain of concrete beams is presented, and the method is independent of external load and takes account of structural nonlinearity. The deflection distribution along the span of a beam-like structure can be predicted from strain response for the whole process of loading (elastic stage, concrete cracking stage and steel yielding stage). Secondly, experiment of a reinforced concrete beam has been conducted to verify the accuracy of the method. Experimental results show that the relative error between the estimated and actual deflection can be controlled within about 5% while the error can reach up to about 70% if structural nonlinearity is not considered. Finally, the influence of error of material parameters and sensor gauge length on deflection estimation has been analyzed. The error of concrete compression strength has a limited influence on deflection prediction while the contribution of tensile concrete should be considered before concrete cracking. The error of area of tensile bars will affect the deflection accuracy after concrete cracking.

  16. Influence of deflection hole angle on effusion cooling in a real combustion chamber condition

    Directory of Open Access Journals (Sweden)

    Liu Xiao

    2015-01-01

    Full Text Available Fluid-solid coupling simulation is conducted to investigate the performance of effusion cooling in the real combustion chamber condition of strong rotation and primary holes. The wall temperature and film cooling effectiveness of different deflection angle is analyzed. From the results, it is concluded that the performance of effusion is better than conventional film cooling. The wall temperature and gradient is lower, the cooling efficiency is higher and the coolant is reduced by 20%, but pressure loss is slightly increased. The cooling effectiveness decreases behind primary holes because of local combustion. Comparison with the effect of deflection angle, the cooling performance of 60 deg deflection angle is best. The coolant is better attached to the wall downstream when the deflection angle is same as the rotating mainstream. In addition, the effect of deflection angle is not so significant on the coolant flow rate, but a large negative impact on the pressure loss. Although the cooling effectiveness of 60 deg deflection angle is highest, the total pressure recovery coefficient is lower. The maximum temperature drops about 70K and the outlet temperature distribution trends more consistent. So various factors should be taken into consideration when designing of deflection angle.

  17. Implementation of Input Block of Minimally Buffered Deflection NoC Router

    Directory of Open Access Journals (Sweden)

    Priti M. Shahane

    2016-08-01

    Full Text Available The traditional system on chip designs employ the shared bus architecture for data transfer in highly integrated Multiprocessor system on chips(MPSoC.Network on chip (NoCis a new paradigm for on chip communication for Multiprocessor systems on chips(MPSoCs. NoCs replace the traditional shared buses system with routing switches. Heart of the NoC is the router and it consists of an input buffer, arbiter, crossbar and an output port. The NoC router uses a buffer to store the incoming packets. These buffers improve the performance but they consume more power and area. Bufferless deflection routing is the solution for improvement in energy efficiency. In this method deflections of the packets take place to overcome the contention problem. But at high network load, deflection routing degrades the performance because of unnecessary hopping of data packets. The MinBD (minimally buffered deflection router is a new router design that uses a small buffer for bufferless deflection routing. In this paper the input block of MinBD router is implemented on FPGA which shows that a small buffer will help to reduce the network deflection rate. It also improves the performance and energy efficiency while buffering only deflected data packets.

  18. New results from the CERN-SPS beam deflection experiments with bent crystals

    Science.gov (United States)

    Baurichter, A.; Kirsebom, K.; Medenwaldt, R.; Møller, S. P.; Worm, T.; Uggerhøj, E.; Mikkelsen, U.; Graftström, P.; Gatignon, L.; Elsener, K.; Doble, N.; Biino, C.; Freund, A.; Vilakazi, Z.; Hage-Ali, M.; Siffert, P.; Clément, M.

    1996-10-01

    Results from five distinct bending experiments performed recently in the H8 beam at CERN are presented. Firstly, deflection of a positive pion beam at 200 GeV/c is compared to the "standard" 450-GeV/c proton beam for a bending angle of 3.1 mrad along the (111) plane in a 50 mm silicon crystal. Second, deflection of negative pions at 200 GeV/c is investigated for the same crystal, for incidence along the (111) plane as well as the axis. Small deflection effects are seen, but no negative particles are bent through the full bending angle of the crystal. Third, the first results from beam deflection at high energy using a germanium crystal are shown. Slightly higher deflection efficiencies than for silicon are seen for large bending angles, but significantly smaller than expected for such a crystal with higher atomic number. Fourth, deflection efficiencies using a strongly irradiated silicon crystal have been measured for the first time, and a small reduction in efficiency is seen in the irradiated region. Finally, deflection of positive particles using axial alignment of a bent silicon crystal has been investigated at 450 GeV/c. Qualitatively similar behaviour as in previous experiments at 12 GeV/c is seen; the beam splits into several beams corresponding to the different planes, and even weak planes are observed.

  19. Real-Time Deflection Monitoring for Milling of a Thin-Walled Workpiece by Using PVDF Thin-Film Sensors with a Cantilevered Beam as a Case Study

    National Research Council Canada - National Science Library

    Luo, Ming; Liu, Dongsheng; Luo, Huan

    2016-01-01

    .... To understand the workpiece deflection behavior in a machining process, a new real-time nonintrusive method for deflection monitoring is presented, and a detailed analysis of workpiece deflection...

  20. Light deflection with torsion effects caused by a spinning cosmic string

    Energy Technology Data Exchange (ETDEWEB)

    Jusufi, Kimet [State University of Tetovo, Physics Department, Tetovo (Macedonia, The Former Yugoslav Republic of)

    2016-06-15

    Using a new geometrical method introduced by Werner, we find the deflection angle in the weak limit approximation by a spinning cosmic string in the context of the Einstein-Cartan (EC) theory of gravity. We begin by adopting the String-Randers optical metric, then we apply the Gauss-Bonnet theorem to the optical geometry and derive the leading terms of the deflection angle in the equatorial plane. Calculation shows that light deflection is affected by the intrinsic spin of the cosmic string and torsion. (orig.)

  1. Cold beam of isotopically pure Yb atoms by deflection using 1D-optical molasses

    Science.gov (United States)

    Rathod, K. D.; Singh, P. K.; Natarajan, Vasant

    2014-09-01

    We demonstrate generation of an isotopically pure beam of laser-cooled Yb atoms by deflection using 1D-optical molasses. Atoms in a collimated thermal beam are first slowed using a Zeeman Slower. They are then subjected to a pair of molasses beams inclined at $45^\\circ$ with respect to the slowed atomic beam. The slowed atoms are deflected and probed at a distance of 160 mm. We demonstrate selective deflection of the bosonic isotope $^{174}$Yb, and the fermionic isotope $^{171}$Yb. Using a transient measurement after the molasses beams are turned on, we find a longitudinal temperature of 41 mK.

  2. Cold beam of isotopically pure Yb atoms by deflection using 1D-optical molasses

    Indian Academy of Sciences (India)

    K D Rathod; P K Singh; Vasant Natarajan

    2014-09-01

    We demonstrate the generation of an isotopically pure beam of laser-cooled Yb atoms by deflection using 1D-optical molasses. Atoms in a collimated thermal beam are first slowed using a Zeeman slower. They are then subjected to a pair of molasses beams inclined at 45° with respect to the slowed atomic beam. The slowed atoms are deflected and probed at a distance of 160 mm. We demonstrate the selective deflection of the bosonic isotope 174Yb and the fermionic isotope 171Yb. Using a transient measurement after the molasses beams are turned on, we find a longitudinal temperature of 41 mK.

  3. Analysis of rolls deflection of Sendzimir mill by 3D FEM

    Institute of Scientific and Technical Information of China (English)

    YU Hai-liang; LIU Xiang-hua; LEE Gyoo Taek

    2007-01-01

    The deflection of rolls of Sendzimir mill with double AS-U-Roll was simulated by finite element method(FEM). The influences of rolling pressure, strip width and rolls-assignment on rolls deflection were analyzed. The results show that the work roll deflection increases with the increase of rolling pressure and the reduction of work roll radius, but the rigid displacement of work roll slightly changes; the work roll end might appear negative displacement for the narrow strip width and high rolling pressure that might cause the contact of work rolls. The research results are significant for guiding production and theoretical analysis of the rolls system of Sendzimir mill.

  4. Self-Deflection of Dark Screening Spatial Solitons Based on Higher-Order Space Charge Field

    Institute of Scientific and Technical Information of China (English)

    ZHANG Guang-Yong; LIU Jin-Song; LIU Shi-Xiong; WANG Cheng; ZHANG Hui-Lan

    2007-01-01

    The effects of higher-order space charge field on the self-deflection of dark screening spatial solitons in biased photorefractive crystals are numerically investigated under steady-state conditions. The expression for an induced space-charge electric field including higher-order space-charge field terms is obtained. Numerical results indicate that dark solitons possess a self-deflection process during propagation, and the solitons always bend in the direction of the c axis of the crystal The self-deflection of dark solitons can experience considerable increase especially in the regime of high bias field strengths.

  5. Mode-locked Lasers Applied to Deflecting a Near Earth Object on Collision Course with Earth

    CERN Document Server

    Fork, Richard; Burgess, Luke; Bergstue, Grant

    2013-01-01

    We consider synchronized trains of sub-picosecond pulses generated by mode-locked lasers applied to deflection of near Earth objects (NEO) on collision course with Earth. Our method is designed to avoid a predicted collision of the NEO with Earth by at least the diameter of Earth. We estimate deflecting a 10,000 MT NEO, such as the asteroid which struck Earth near Chelyabinsk, Russia to be feasible within several months using average power in the ten kilowatt range. We see this deflection method as scalable to larger NEO to a degree not possible using continuous laser systems.

  6. Photonic-based laser driven electron beam deflection and focusing structures

    Directory of Open Access Journals (Sweden)

    T. Plettner

    2009-10-01

    Full Text Available We propose a dielectric photonic structure for ultrafast deflection and focusing of relativistic charged particle beams. The structure is designed to transform a free-space laser beam into a deflection force that acts on the free particles with the same optical phase over a distance of travel that is much greater than the laser wavelength. The proposed structure has a two-dimensional geometry and is compatible with existing nanofabrication methods. Deflection fields of GV/m magnitude and subfemtosecond switching speeds are expected to be possible from these dielectric structures. With these elements a submeter scale extreme ultraviolet synchrotron source seems feasible.

  7. Light deflection with torsion effects caused by a spinning cosmic string

    Science.gov (United States)

    Jusufi, Kimet

    2016-06-01

    Using a new geometrical method introduced by Werner, we find the deflection angle in the weak limit approximation by a spinning cosmic string in the context of the Einstein-Cartan (EC) theory of gravity. We begin by adopting the String-Randers optical metric, then we apply the Gauss-Bonnet theorem to the optical geometry and derive the leading terms of the deflection angle in the equatorial plane. Calculation shows that light deflection is affected by the intrinsic spin of the cosmic string and torsion.

  8. Multipole Field Effects for the Superconducting Parallel-Bar Deflecting/Crabbing Cavities

    Energy Technology Data Exchange (ETDEWEB)

    De Silva, Payagalage Subashini Uddika [Thomas Jefferson National Accelerator Facility, Newport News, VA (United States) and Old Dominion University, Norfolk, VA (United States); Delayen, Jean Roger [Old Dominion University, Norfolk, VA (United States)

    2012-09-01

    The superconducting parallel-bar deflecting/crabbing cavity is currently being considered as one of the design options in rf separation for the Jefferson Lab 12 GeV upgrade and for the crabbing cavity for the proposed LHC luminosity upgrade. Knowledge of multipole field effects is important for accurate beam dynamics study of rf structures. The multipole components can be accurately determined numerically using the electromagnetic surface field data in the rf structure. This paper discusses the detailed analysis of those components for the fundamental deflecting/crabbing mode and higher order modes in the parallel-bar deflecting/crabbing cavity.

  9. Light Deflection with Torsion Effects Caused by a Spinning Cosmic String

    CERN Document Server

    Jusufi, Kimet

    2016-01-01

    Using a new geometrical method introduced by Werner, we find the deflection angle in the weak limit approximation by a spinning cosmic string in the context of the Einstein-Cartan (EC) theory of gravity. We begin by adopting the String-Randers optical metric, then we apply the Gauss-Bonnet theorem to the optical geometry and derive the leading terms of the deflection angle in the equatorial plane. Calculations shows that light deflection is affected by the intrinsic spin of the cosmic string and torsion.

  10. The importance of being elastic: deflection of a badminton racket during a stroke.

    Science.gov (United States)

    Kwan, Maxine; Rasmussen, John

    2010-03-01

    The deflection profiles of a badminton racket during strokes performed by elite and world-class badminton players were recorded by strain gauges and subsequently analysed to determine the role of shaft stiffness in racket performance. Deflection behaviour was consistent in all strokes across all players, suggesting a controlled use of racket elasticity. In addition, all impacts occurred within 100 ms of each other, a duration in which deflection velocity provides an increase in racket velocity, indicating that the players were able to use racket elasticity to their advantage. Since deflection behaviour is a product of the racket-player interaction, further work is required to determine the effects of different racket properties and player techniques on the elastic response of rackets during strokes.

  11. Deflection of light ray due to a charged body using Material Medium Approach

    CERN Document Server

    Roy, Saswati

    2015-01-01

    The gravitational deflection of light ray is an important prediction of General Theory of Relativity. In this paper we develop analytical expression of the deflection of light ray without any weak field approximation due to a charged gravitational body represented by Reissner_Nordstr\\"om (RN) and Janis-Newman-Winicour (JNW) space time geometry, using material medium approach. It is concluded that although both the geometries represent the charged, non-rotating, spherically symmetric gravitating body, but the effect of charge on the gravitational deflection is just opposite to each other. The gravitational deflection decreases with charge in the RN geometry and increases with charge in the JNW geometry. The calculations obtained here are compared with other methods done by different authors. The formalism is applied to an arbitrary selected pulsar PSRB1937+21 as a gravitating body, as a test case.

  12. Analysis of Deflection Problems of Large-span Continuous Rigid Frame Bridge and Prevention Measures

    Directory of Open Access Journals (Sweden)

    Chen Dong

    2015-01-01

    Full Text Available The large-span continuous rigid frame bridge is a kind of common structural form in long-span bridges of our country, but one of the main diseases of these bridges is the excessive deflection in the mid-span, which seriously affects the safety of the structure. This paper makes a comprehensive analysis for the causes of the excessive deflection, and lists the commonly-used control measures in engineering. Simultaneously, new improvement measures and the comparative analysis of before-and-after improvements are put forward on this basis. However, these measures can be used to inhibit deflection in a certain extent, but cannot avoid the occurrence of deflection completely.

  13. Evaluation of Accuracy and Precision of Several Highway Speed Deflection Devices

    OpenAIRE

    Rada, Gonzalo R; Visintine, Beth A.; Rocha,Sergio; Velarde, Jorge; Gallardo, Paola; Nazarian, Soheil; Siddharthan, Rajaratnam V.; Nasimifar, Seyyed

    2014-01-01

    Structural Session 2: Evaluation of Deflection Devices Moderated by Doug Chalman This presentation was held at the Pavement Evaluation 2014 Conference, which took place from September 15-18, 2014 in Blacksburg, Virginia. Presentation only

  14. Design and Development of Superconducting Parallel-Bar Deflecting/Crabbing Cavities

    Energy Technology Data Exchange (ETDEWEB)

    Payagalage Subashini Uddi De Silva, Jean Delayen

    2012-07-01

    The superconducting parallel-bar cavity is a deflecting/crabbing cavity with attractive properties that is being considered for a number of applications. We present the designs of a 499 MHz deflecting cavity developed for the Jefferson Lab 12 GeV Upgrade and a 400 MHz crabbing cavity for the LHC High Luminosity Upgrade. Prototypes of these two cavities are now under development and fabrication.

  15. Encoding whisker deflection velocity within the rodent barrel cortex using phase-delayed inhibition.

    Science.gov (United States)

    Liu, Runjing; Patel, Mainak; Joshi, Badal

    2014-12-01

    The primary sensory feature represented within the rodent barrel cortex is the velocity with which a whisker has been deflected. Whisker deflection velocity is encoded within the thalamus via population synchrony (higher deflection velocities entail greater synchrony among the corresponding thalamic population). Thalamic (TC) cells project to regular spiking (RS) cells within the barrel cortex, as well as to inhibitory cortical fast-spiking (FS) neurons, which in turn project to RS cells. Thus, TC spikes result in EPSPs followed, with a small time lag, by IPSPs within an RS cell, and hence the RS cell decodes TC population synchrony by employing a phase-delayed inhibition synchrony detection scheme. As whisker deflection velocity is increased, the probability that an RS cell spikes rises, while jitter in the timing of RS cell spikes remains constant. Furthermore, repeated whisker deflections with fixed velocity lead to system adaptation--TC →RS, TC →FS, and FS →RS synapses all weaken substantially, leading to a smaller probability of spiking of the RS cell and increased jitter in the timing of RS cell spikes. Interestingly, RS cell activity is better able to distinguish among different whisker deflection velocities after adaptation. In this work, we construct a biophysical model of a basic 'building block' of barrel cortex - the feedforward circuit consisting of TC cells, FS cells, and a single RS cell - and we examine the ability of the purely feedforward circuit to explain the experimental data on RS cell spiking probability, jitter, adaptation, and deflection velocity discrimination. Moreover, we study the contribution of the phase-delayed inhibition network structure to the ability of an RS cell to decode whisker deflection velocity encoded via TC population synchrony.

  16. Strong deflection lensing by charged black holes in scalar-tensor gravity

    Energy Technology Data Exchange (ETDEWEB)

    Eiroa, Ernesto F.; Sendra, Carlos M. [Instituto de Astronomia y Fisica del Espacio (IAFE, CONICET-UBA), Buenos Aires (Argentina); Universidad de Buenos Aires, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Buenos Aires (Argentina)

    2014-11-15

    We examine a class of charged black holes in scalar-tensor gravity as gravitational lenses. We find the deflection angle in the strong deflection limit, from which we obtain the positions and the magnifications of the relativistic images. We compare our results with those corresponding to the Reissner-Norstroem spacetime and we analyze the observational aspects in the case of the Galactic supermassive black hole. (orig.)

  17. Influence of tool deflection on micro channel pattern of 6:4 brass with rectangular tool

    Institute of Scientific and Technical Information of China (English)

    Tae-Jin JE; Kang-Won LEE; Sang-Cheon PARK; Jae-Gu KIM; Doo-Sun CHOI; Kyoung-Taik PARK; Kyung-Hyun WHANG

    2009-01-01

    Machining experiment of micro channel structure with 6:4 brass was carried out by shaping process using a single crystal diamond tool. FEM simulation using solid cantilever beam model was analyzed. In result of experiment, tool deflection is observed as machining characteristics through result of experiments such as surface roughness, cutting force and burr formations. And the influence of tool deflection is experimentally proved.

  18. Prediction of Extrusion Pressure And Product Deflection Of Using Artificial Neural Network

    Directory of Open Access Journals (Sweden)

    D.T. GUNDU

    2013-01-01

    Full Text Available - In this paper artificial neural network was used as a modeling tool for simulation and prediction of extrusion pressure and product deflection of extrudes of lead alloys. An extensive experimental program was undertaken to extrude a lead (Pb alloy on ELE Compact-1500 compression machine. The neural model of extrusion pressure and product deflection was developed based on groups of experiments carried out as samples, Eight (8 die bearing parameters (die bearing length, radius of curvature, slip angle, die angle, die ratio ram displacement, pocket depth and die diameter were used as inputs into the network architecture of 8 [4-3]2 2 in predicting the extrusion pressure and product deflection. After series of network architectures were trained using different training algorithms such as Levenberg-Marquardt, Bayesian Regulation, Resilient Backpropagation using MATLAB 7.9.0 (R20096, the LM8 [4-3]2 2 was selected as the most appropriate model. Prediction of the neural model exhibited reasonable correlation with the experimental extrusion pressure and product deflection. The predicted extrusion pressure and product deflection gave reasonable errors and higher correlation coefficients indicating that the model is robust for predicting extrusion pressure and product deflection.

  19. Large deflection and rotation of Timoshenko beams with frictional end supports under three-point bending

    Science.gov (United States)

    Li, Dao-Kui; Li, Xian-Fang

    2016-08-01

    Three-point bending of a beam is studied based on the Timoshenko beam theory. Large deflection and large rotation of a beam resting on simple supports with friction are calculated for a concentrated force acting at the midspan. Using the Lagrangian kinematic relations, a system of non-linear differential equations are obtained for a prismatic shear-deformable Timoshenko beam. Exact solutions for the deflection, horizontal displacement, and rotation of cross-section are derived analytically. Two deflections of small and large scale exist under three-point bending. The solutions corresponding to linearized model coincide with the well-known solutions to the classical Timoshenko beams. Numerical calculations are carried out to show the effect of the important parameters such as shear rigidity of the beam and the coefficient of friction at the contact position between the beam and supports on the deflection. The load-deflection curves are graphically presented. A comparison of large deflections and large rotations with their classical counterparts and with experimental data is made. The obtained results are useful in safety design of linear and non-linear beams subject to three-point bending.

  20. Using ForeCAT Deflections and Rotations to Constrain the Early Evolution of CMEs

    CERN Document Server

    Kay, C; Colaninno, R C; Vourlidas, A

    2016-01-01

    To accurately predict the space weather effects of coronal mass ejection (CME) impacts at Earth one must know if and when a CME will impact Earth, and the CME parameters upon impact. Kay et al. (2015b) presents Forecasting a CME's Altered Trajectory (ForeCAT), a model for CME deflections based on the magnetic forces from the background solar magnetic field. Knowing the deflection and rotation of a CME enables prediction of Earth impacts, and the CME orientation upon impact. We first reconstruct the positions of the 2008 April 10 and the 2012 July 12 CMEs from the observations. The first of these CMEs exhibits significant deflection and rotation (34 degrees deflection and 58 degrees rotation), while the second shows almost no deflection or rotation (<3 degrees each). Using ForeCAT, we explore a range of initial parameters, such as the CME location and size, and find parameters that can successfully reproduce the behavior for each CME. Additionally, since the deflection depends strongly on the behavior of a ...

  1. A novel deflection shape function for rectangular capacitive micromachined ultrasonic transducer diaphragms

    Directory of Open Access Journals (Sweden)

    Zhou Zheng

    2015-09-01

    Full Text Available A highly accurate analytical deflection shape function that describes the deflection profiles of capacitive micromachined ultrasonic transducers (CMUTs with rectangular membranes under electrostatic pressure has been formulated. The rectangular diaphragms have a thickness range of 0.6–1.5 μm and a side length range of 100–1000 μm. The new deflection shape function generates deflection profiles that are in excellent agreement with finite element analysis (FEA results for a wide range of geometry dimensions and loading conditions. The deflection shape function is used to analyze membrane deformations and to calculate the capacitances between the deformed membranes and the fixed back plates. In 50 groups of random tests, compared with FEA results, the calculated capacitance values have a maximum deviation of 1.486% for rectangular membranes. The new analytical deflection function can provide designers with a simple way of gaining insight into the effects of designed parameters for CMUTs and other MEMS-based capacitive type sensors.

  2. Evaluation of cuspal deflection in premolar teeth restored with low shrinkable resin composite (in vitro study).

    Science.gov (United States)

    Labib, Labib Mohamed; Nabih, Sameh Mahmoud; Baroudi, Kusai

    2015-01-01

    This study evaluated cuspal deflection in premolar teeth restored with low shrinkable resin composite. A total of 40 human premolars were used for cuspal deflection evaluation in this study. Each group was divided into four equal groups according to the type of resin composite and the adhesive used as follows: group A: Using low shrinkable resin composite (silorane) with its adhesive system; group B: Using low shrinkable composite (silorane) with G-bond; group C: Using Filtek Z350 composite with G-bond; and group D: Using Filtek Z350 composite with AdheSE. Cusp deflection was detected using Universal measuring microscope and laser horizontal metroscope. This study was done to investigate the effect of polymerization shrinkage stresses of two resin composite materials (Filtek Z350 and Filtek P90) on cuspal deflection of mesio-occluso-distal restoration. For this study, the extracted non-carious maxillary second premolars were selected. Forty teeth that showed no more than 5% variation in their dimensions were used. A significant increase in cuspal deflection of cavities restored with the methacrylate-based (Filtek Z350) compared with the silorane (P90) resin-based composites was obtained. The change in the organic matrix or materials formulation of the resin composite using silorane has a positive effect on controlling the cusp deflection.

  3. Investigation of UWB Wind Turbine Blade Deflection Sensing with a Tip Antenna inside a Blade

    DEFF Research Database (Denmark)

    Zhang, Shuai; Jensen, Tobias Lindstrøm; Franek, Ondrej;

    2016-01-01

    An UWB blade deflection sensing system with a tip antenna inside a blade is investigated in this paper. The lower UWB band of 3.1-5.3 GHz is utilized. This system composes of two UWB radio links between one antenna inside the blade tip and two antennas outside the blade root. Blade deflections ar......, and the sensing system can realize the deflection tracking with a maximum deviation of 0.21 m and root mean squared error of 0.11 m.......An UWB blade deflection sensing system with a tip antenna inside a blade is investigated in this paper. The lower UWB band of 3.1-5.3 GHz is utilized. This system composes of two UWB radio links between one antenna inside the blade tip and two antennas outside the blade root. Blade deflections......-blade time-domain measurements are proposed to verify the simulations and realize the blade deflection sensing with an in-blade tip antenna. With the optimized in-blade tip antenna polarization and two root antenna locations, an accuracy of 2 cm is achieved for the tip-root antenna distance estimation...

  4. UWB Wind Turbine Blade Deflection Sensing for Wind Energy Cost Reduction.

    Science.gov (United States)

    Zhang, Shuai; Jensen, Tobias Lindstrøm; Franek, Ondrej; Eggers, Patrick C F; Olesen, Kim; Byskov, Claus; Pedersen, Gert Frølund

    2015-08-12

    A new application of utilizing ultra-wideband (UWB) technology to sense wind turbine blade deflections is introduced in this paper for wind energy cost reduction. The lower UWB band of 3.1-5.3 GHz is applied. On each blade, there will be one UWB blade deflection sensing system, which consists of two UWB antennas at the blade root and one UWB antenna at the blade tip. The detailed topology and challenges of this deflection sensing system are addressed. Due to the complexity of the problem, this paper will first realize the on-blade UWB radio link in the simplest case, where the tip antenna is situated outside (and on the surface of) a blade tip. To investigate this case, full-blade time-domain measurements are designed and conducted under different deflections. The detailed measurement setups and results are provided. If the root and tip antenna locations are properly selected, the first pulse is always of sufficient quality for accurate estimations under different deflections. The measured results reveal that the blade tip-root distance and blade deflection can be accurately estimated in the complicated and lossy wireless channels around a wind turbine blade. Some future research topics on this application are listed finally.

  5. Experimental Estimating Deflection of a Simple Beam Bridge Model Using Grating Eddy Current Sensors

    Directory of Open Access Journals (Sweden)

    Hui Zhao

    2012-07-01

    Full Text Available A novel three-point method using a grating eddy current absolute position sensor (GECS for bridge deflection estimation is proposed in this paper. Real spatial positions of the measuring points along the span axis are directly used as relative reference points of each other rather than using any other auxiliary static reference points for measuring devices in a conventional method. Every three adjacent measuring points are defined as a measuring unit and a straight connecting bar with a GECS fixed on the center section of it links the two endpoints. In each measuring unit, the displacement of the mid-measuring point relative to the connecting bar measured by the GECS is defined as the relative deflection. Absolute deflections of each measuring point can be calculated from the relative deflections of all the measuring units directly without any correcting approaches. Principles of the three-point method and displacement measurement of the GECS are introduced in detail. Both static and dynamic experiments have been carried out on a simple beam bridge model, which demonstrate that the three-point deflection estimation method using the GECS is effective and offers a reliable way for bridge deflection estimation, especially for long-term monitoring.

  6. Record Deflection Efficiencies Measured for High Energy Protons in a Bent Germanium Crystal

    Science.gov (United States)

    Elsener, K.; Biino, C.; Clement, M.; Doble, N.; Gatignon, L.; Grafstrom, P.; Mikkelsen, U.; Kirsebom, K.; Møller, S. P.; Uggerhøj, E.; Worm, T.; Freund, A.

    1997-05-01

    New experimental results on the deflection of 450 GeV/c and 200 GeV/c protons in a bent Ge crystal are presented. At 450 GeV/c, the 50 mm long crystal gave record deflection efficiencies up to 60% for small angles (1 mrad), while at angles as large as 12 mrad, the efficiency is about 25 times larger than for a silicon crystal of the same size. Measurements up to 20 mrad deflection angle have been performed at 200 GeV/c as well as 450 GeV/c - the lower bending dechanneling leads to a rather slow decrease in efficiency at lower momenta, and 15% of the 200 GeV/c beam hitting the crystal are still deflected at the largest angles measured. These experimental results are in good agreement with a model for channeling deflection developed by Ellison and give confidence in extrapolations to higher energies (e.g. to LHC), other crystal materials or different deflection angles.

  7. Compensations of beamlet deflections for 1 MeV accelerator of ITER NBI

    Science.gov (United States)

    Kashiwagi, Mieko; Taniguchi, Masaki; Umeda, Naotaka; Dairaku, Masayuki; Tobari, Hiroyuki; Yamanaka, Haruhiko; Watanabe, Kazuhiro; Inoue, Takashi; de Esch, H. P. L.; Grisham, Larry R.; Boilson, Deirdre; Hemsworth, Ronald S.; Tanaka, Masanobu

    2013-02-01

    Compensation methods of beamlet deflections have been studied in a three dimensional (3D) beam analysis using OPERA-3d code for 1 MeV accelerator of the ITER neutral beam injector (NBI). The beamlet deflection is caused by i) magnetic field generated by permanent magnets embedded in the extraction grid (EXG) for electron suppression and ii) space charge repulsion between the beamlets and beam groups. Moreover, the beamlet deflection is caused due to electric field distortion formed by a grid support structure. In order to compensate the beamlet deflections due to i) and ii), an aperture offset of 0.6 mm was applied in the electron suppression grid (ESG) and a metal bar with 3 mm in thickness, so-called a kerb, was attached around the aperture area at the back side of the ESG, respectively. Detailed configuration of the compensation methods was also considered so as to suppress the beam spread due to the electric field distortion and to lower electric field concentrations at the edge of the kerb. For the beamlets near the grid support structure, the beamlet deflection due to the space charge repulsion could be negated due to the electric field distortion formed by the grid support structure.

  8. Feasibility study on a strain based deflection monitoring system for wind turbine blades

    Science.gov (United States)

    Lee, Kyunghyun; Aihara, Aya; Puntsagdash, Ganbayar; Kawaguchi, Takayuki; Sakamoto, Hiraku; Okuma, Masaaki

    2017-01-01

    The bending stiffness of the wind turbine blades has decreased due to the trend of wind turbine upsizing. Consequently, the risk of blades breakage by hitting the tower has increased. In order to prevent such incidents, this study proposes a deflection monitoring system that can be installed to already operating wind turbine's blades. The monitoring system is composed of an estimation algorithm to detect blade deflection and a wireless sensor network as a hardware equipment. As for the estimation method for blade deflection, a strain-based estimation algorithm and an objective function for optimal sensor arrangement are proposed. Strain-based estimation algorithm is using a linear correlation between strain and deflections, which can be expressed in a form of a transformation matrix. The objective function includes the terms of strain sensitivity and condition number of the transformation matrix between strain and deflection. In order to calculate the objective function, a simplified experimental model of the blade is constructed by interpolating the mode shape of a blade from modal testing. The interpolation method is effective considering a practical use to operating wind turbines' blades since it is not necessary to establish a finite element model of a blade. On the other hand, a sensor network with wireless connection with an open source hardware is developed. It is installed to a 300 W scale wind turbine and vibration of the blade on operation is investigated.

  9. Fusion of electromagnetic trackers to improve needle deflection estimation: simulation study.

    Science.gov (United States)

    Sadjadi, Hossein; Hashtrudi-Zaad, Keyvan; Fichtinger, Gabor

    2013-10-01

    We present a needle deflection estimation method to anticipate needle bending during insertion into deformable tissue. Using limited additional sensory information, our approach reduces the estimation error caused by uncertainties inherent in the conventional needle deflection estimation methods. We use Kalman filters to combine a kinematic needle deflection model with the position measurements of the base and the tip of the needle taken by electromagnetic (EM) trackers. One EM tracker is installed on the needle base and estimates the needle tip position indirectly using the kinematic needle deflection model. Another EM tracker is installed on the needle tip and estimates the needle tip position through direct, but noisy measurements. Kalman filters are then employed to fuse these two estimates in real time and provide a reliable estimate of the needle tip position, with reduced variance in the estimation error. We implemented this method to compensate for needle deflection during simulated needle insertions and performed sensitivity analysis for various conditions. At an insertion depth of 150 mm, we observed needle tip estimation error reductions in the range of 28% (from 1.8 to 1.3 mm) to 74% (from 4.8 to 1.2 mm), which demonstrates the effectiveness of our method, offering a clinically practical solution.

  10. An improved equivalent circuit model of a four rod deflecting cavity

    Science.gov (United States)

    Apsimon, R.; Burt, G.

    2017-03-01

    In this paper we present an improved equivalent circuit model for a four rod deflecting cavity which calculates the frequencies of the first four modes of the cavity as well as the RT/Q for the deflecting mode. Equivalent circuit models of RF cavities give intuition and understanding about how the cavity operates and what changes can be made to modify the frequency, without the need for RF simulations, which can be time-consuming. We parameterise a generic four rod deflecting cavity into a geometry consisting of simple shapes. Equations are derived for the line impedance of the rods and the capacitance between the rods and these are used to calculate the resonant frequency of the deflecting dipole mode as well as the lower order mode and the model is bench-marked against two test cases; the CEBAF separator and the HL-LHC 4-rod LHC crab cavity. CST and the equivalent circuit model agree within 4% for both cavities with the LOM frequency and within 1% for the deflecting frequency. RT/Q differs between the model and CST by 37% for the CEBAF separator and 25% for the HL-LHC 4-rod crab cavity; however this is sufficient for understanding how to optimise the cavity design. The model has then been utilised to suggest a method of separating the modal frequencies in the HL-LHC crab cavity and to suggest design methodologies to optimise the cavity geometries.

  11. Laser heating of a cavity versus a plane surface for metal targets utilizing photothermal deflection measurements

    Science.gov (United States)

    Jeong, S. H.; Greif, R.; Russo, R. E.

    1996-08-01

    The effects of a cylindrical cavity in a metal surface on the energy coupling of a laser beam with the solid were investigated by using a photothermal deflection technique. The photothermal deflection of a probe beam over the cavity was measured while the bottom of the cavity was heated with a Nd-YAG laser with a wavelength of 1064 nm. Cavities in three different materials and with two different aspect ratios were used for the experiment. Temperature distributions in the solid and the surrounding air were computed numerically and used to calculate photothermal deflections for cavity heating and for plane surface heating. Reflection of the heating laser beam inside the cavity increased the photothermal deflection amplitude significantly with larger increases for materials with larger thermal diffusivity. The computed photothermal deflections agreed more closely with the experimental results when reflection of the heating laser beam inside the cavity was included in the numerical model. The overall energy coupling between a heating laser and a solid is enhanced by a cavity.

  12. Deflection of 32.8 TeV/c fully stripped Pb ions by means of a bent Si crystal

    CERN Document Server

    Biino, C; Doble, Niels T; Elsener, K; Gatignon, L; Grafström, P; Herr, Werner; Keppler, P; Major, J V; Mikkelsen, U; Taratin, A; Velasco, M

    2000-01-01

    New results on the deflection of fully stripped 32.8 TeV/c Pb ions in a bent Si crystal at the CERN-SPS are reported. Deflection efficiencies above 10% have been measured for deflection angles in the range 4-9 mrad.The effect of particle losses due to interaction in the crystal and other systematic errors have been carefully investigated. The experimental results are in agreement with theoretical calculations

  13. Deflection of 32.8 TeV/c fully stripped Pb ions by means of a bent Si crystal

    Energy Technology Data Exchange (ETDEWEB)

    Biino, C.; Clement, M.; Doble, N.; Elsener, K. E-mail: konrad.elsener@cern.ch; Gatignon, L.; Grafstroem, P.; Herr, W.; Keppler, P.; Major, J.; Mikkelsen, U.; Taratin, A.; Velasco, M

    2000-04-01

    New results on the deflection of fully stripped 32.8 TeV/c Pb ions in a bent Si crystal at the CERN-SPS are reported. Deflection efficiencies above 10% have been measured for deflection angles in the range 4-9 mrad. The effect of particle losses due to interaction in the crystal and other systematic errors have been carefully investigated. The experimental results are in agreement with theoretical calculations.

  14. Deflection of 32.8 TeV/c fully stripped Pb ions by means of a bent Si crystal

    Science.gov (United States)

    Biino, C.; Clément, M.; Doble, N.; Elsener, K.; Gatignon, L.; Grafström, P.; Herr, W.; Keppler, P.; Major, J.; Mikkelsen, U.; Taratin, A.; Velasco, M.

    2000-03-01

    New results on the deflection of fully stripped 32.8 TeV/c Pb ions in a bent Si crystal at the CERN-SPS are reported. Deflection efficiencies above 10% have been measured for deflection angles in the range 4-9 mrad. The effect of particle losses due to interaction in the crystal and other systematic errors have been carefully investigated. The experimental results are in agreement with theoretical calculations.

  15. Solar system constraints on asymptotically flat IR modified Horava gravity through light deflection

    CERN Document Server

    Liu, Molin; Yu, Benhai; Lu, Jianbo

    2010-01-01

    In this paper, we study the motion of photons around a Kehagias-Sfetsos (KS) black hole and obtain constraints on IR modified Ho$\\check{r}$ava gravity without cosmological constant ($\\sim \\Lambda_{W}$). An analytic formula for the light deflection angle is obtained. For a propagating photon, the deflection angle $\\delta \\varphi$ increases with large values of the Ho$\\check{r}$ava gravity parameter $\\omega$. Under the UV limit $\\omega \\longrightarrow \\infty$, deflection angle reduces to the result of usual Schwarzschild case, $4GM/R$. It is also found that with increasing scale of astronomical observation system the Ho$\\check{r}$ava-Lifshitz gravity should satisfy $|\\omega M^2|>1.1725 \\times10^{-16}$ with $12%$ precision for Earth system, $|\\omega M^2| > 8.27649 \\times 10^{-17}$ with $17%$ precision for Jupiter system and $|\\omega M^2| > 8.27650\\times 10^{-15}$ with $0.17%$ precision for solar system.

  16. The deflection of light induced by the Sun's gravitational field and measured with geodetic VLBI

    CERN Document Server

    Titov, O

    2015-01-01

    The Sun's gravitational field deflects the apparent positions of close objects in accordance with the formulae of general relativity. Optical astrometry is used to test the prediction, but only with the stars close to the Sun and only during total Solar eclipses. Geodetic Very Long Baseline Interferometry (VLBI) is capable of measuring the deflection of the light from distant radio sources anytime and across the whole sky. We show that the effect of light deflection is equivalent to the gravitational delay calculated during the reduction of VLBI data. All reference radio sources display an annual circular motion with the magnitude proportional to their ecliptic latitude. In particular, radio sources near the ecliptic pole draw an annual circle with magnitude of 4 mas. This effect could be easily measured with the current precision of the geodetic VLBI data.

  17. Flame four-dimensional deflection tomography with compressed-sensing-revision reconstruction

    Science.gov (United States)

    Zhang, Bin; Zhao, Minmin; Liu, Zhigang; Wu, Zhaohang

    2016-08-01

    Deflection tomography with limited angle projections was investigated to visualize a premixed flame. A projection sampling system for deflection tomography was used to obtain chronological deflectogram arrays at six view angles with only a pair of gratings. A new iterative reconstruction algorithm with deflection angle compressed-sensing revision was developed to improve reconstruction-distribution quality from incomplete projection data. Numerical simulation and error analysis provided a good indication of algorithm precision and convergence. In the experiment, 150 fringes were processed, and temperature distributions in 20 cross-sections were reconstructed from projection data in four instants. Four-dimensional flame structures and temperature distributions in the flame interior were visualized using the visualization toolkit. The experimental reconstruction was then compared with the result obtained from computational fluid dynamic analysis.

  18. Converse Piezoelectric Effect Induced Transverse Deflection of a Free-Standing ZnO Microbelt

    KAUST Repository

    Hu, Youfan

    2009-07-08

    We demonstrate the first electric field induced transverse deflection of a single-crystal, free-standing ZnO microbelt as a result of converse piezoelectric effect. For a microbelt growing along the c-axis, a shear stress in the a-c plane can be induced when an electric field E is applied along the a-axis of the wurtzite structure. As amplified by the large aspect ratio of the microbelt that grows along the c-axis, the strain localized near the root can be detected via the transverse deflection perpendicular to the ZnO microbelt. After an experimental approach was carefully designed and possible artifacts were ruled out, the experimentally observed degree of deflection of the microbelt agrees well with the theoretically expected result. The device demonstrated has potential applications as transverse actuators/sensors/switches and electric field induced mechanical deflectors. © 2009 American Chemical Society.

  19. High power RF system for transverse deflecting structure XFEL TDS INJ

    Science.gov (United States)

    Volobuev, E. N.; Zavadtsev, A. A.; Zavadtsev, D. A.; Smirnov, A. J.; Sobenin, N. P.; Churanov, D. V.

    2016-09-01

    The high power RF system (HPRF) is designed for RF feeding of the transverse deflecting structure of the transverse deflecting system XFEL TDS System INJ of the European X-ray Free Electron Laser. The HPRF system includes klystron, waveguide ceramic windows, directional couplers, waveguide vacuum units, spark detector and waveguide line. Operating frequency is 2997.2 MHz. Peak input power is up to 3 MW. The HPRF system has been developed, manufactured and assembled in the XFEL Injector building. The total length of the waveguide line is 55 m from the klystron at the -5 floor to the transverse deflecting structure at the -7 floor. All designed RF parameters have been obtained experimentally at low RF power level.

  20. Deflection and Vibration Control of Laminated Plates Using Extension and Shear Actuated Fiber Composites

    Directory of Open Access Journals (Sweden)

    S. Raja

    2011-01-01

    Full Text Available The use of surface bonded and embedded piezoelectric composite actuators is examined through a numerical study. Modelling schemes are therefore developed by applying the isoparametric finite element approach to idealise extension-bending and shear-bending couplings due to piezoelectric actuations. A modal control based linear quadratic regulator is employed to perform the active vibration control studies. Influence of shear actuation direction and its width has been examined and interesting deflection patterns are noticed. The through width SAFC develops a constant deflection beyond its length along the laminated plate length. In contrast, segmented SAFC produces a moderate to linearly varying deflection pattern. MFC actuators have shown promising features in vibration control performances. Nevertheless, closed loop damping presents the efficiency of SAFC in the vibration control application. It is therefore envisaged that optimally actuated smart laminates can be designed using MFC and SAFC to efficiently counteract the disturbance forces.

  1. Cryogenic Test of a Proof-of-Principle Superconducting RF-Dipole Deflecting and Crabbing Cavity

    CERN Document Server

    De Silva, S U; Delayen, Jean Roger

    2013-01-01

    Recent applications in need of compact low-frequency deflecting and crabbing cavities have initiated the design and development of new superconducting structures operating at high gradients with low losses. Previously, TM$_{110}$ -type deflecting and crabbing cavities were developed and have also been operated successfully. However, these geometries are not favorable designs for low operating frequencies. The superconducting rf-dipole cavity is the first compact deflecting and crabbing geometry that has demonstrated high gradients and high shunt impedance. Since the fundamental operating mode is the lowest mode and is widely separated from the nearest higher order mode, the rf-dipole design is an attractive geometry for effective damping of the higher order modes in high current applications. A 400 MHz rf-dipole cavity was designed, fabricated, and tested as a proof-of-principle cavity. The cavity achieved high operating gradients, and the multipacting levels were easily processed and did not reoccur.

  2. Simultaneous Optical Measurements of Axial and Tangential Steady-State Blade Deflections

    Science.gov (United States)

    Kurkov, Anatole P.; Dhadwal, Harbans S.

    1999-01-01

    Currently, the majority of fiber-optic blade instrumentation is being designed and manufactured by aircraft-engine companies for their own use. The most commonly employed probe for optical blade deflection measurements is the spot probe. One of its characteristics is that the incident spot on a blade is not fixed relative to the blade, but changes depending on the blade deformation associated with centrifugal and aerodynamic loading. While there are geometrically more complicated optical probe designs in use by different engine companies, this paper offers an alternate solution derived from a probe-mount design feature that allows one to change the probe axial position until the incident spot contacts either a leading or a trailing edge. By tracing the axial position of either blade edge one is essentially extending the deflection measurement to two dimensions, axial and tangential. The blade deflection measurements were obtained during a wind tunnel test of a fan prototype.

  3. Deflected anomaly mediated SUSY breaking scenario with general messenger–matter interactions

    Directory of Open Access Journals (Sweden)

    Fei Wang

    2015-12-01

    Full Text Available We propose to introduce general messenger–matter interactions in the deflected anomaly mediated SUSY breaking scenario. The most general form for the resulting soft parameters is derived. New interference terms between the GMSB type and AMSB type contributions are the unique feature of this scenario. Messenger–matter interactions involving sleptons can be used to solve the tachyonic slepton problem and naturally lead to positive slepton masses regardless of the sign of deflection parameter. Besides, due to the new contributions, large |At| that will not trigger color-breaking stop VEV are also possible in this scenario, thus can easily give the 125 GeV higgs which was discovered by LHC. This type of deflected AMSB scenario need very few messenger species, thus can avoid possible non-perturbative gauge couplings below the GUT scale (or Landau pole below the Planck scale.

  4. Enhanced Deflection of Light Ray by Atomic Ensemble on Coherent Population Oscillation

    Institute of Scientific and Technical Information of China (English)

    LU Jing; ZHOU Lan; KUANG Le-Man

    2009-01-01

    In recent experiments [e.g., Nature Physics 2 (2006) 332], the enhanced light deflection in an atomic ensemble due to inhomogeneous fields is demonstrated by the electromagnetically induced transparency (EIT) based mechanism. In this paper, we explore a different mechanism for the similar phenomenon of the enhanced light deflection.This mechanism is based on the coherent population oscillation, which leads to the hole burning in the absorption spectrum. The medium causing the deflection of probe light is an ensemble of two-level atoms manipulated by a strong controlled field on the two photon resonances. In the large detuning condition, the response of the medium to the pump field and signal field is obtained with steady state approximation. And it is found that after the probe field travels across the medium, the signal ray bends due to the spatial-dependent profile of the control beam.

  5. The Influence of the Supporting Wheel Deflection of Large-scale Rotary Kiln on Maximum Contact Stress

    Institute of Scientific and Technical Information of China (English)

    Li Xuejun; Qiu Weiliang; Yuan Yincai; Li Ping

    2006-01-01

    The relation between the maximum contact stress ratio and deflection angle is derived from Hertz contact theory when the deflection of rotary kiln supporting wheel happens. According to the analysis of practical example, the maximum contact stress ratio within the deflection range of rotary kiln supporting wheel is listed. The contact stress will increase largely when rotary kiln supporting wheel deflects with little angle,which probably will result in accidents correlating to safety. This will provide theory conference for the design,the operating condition analysis and adjusting of the rotary kiln.

  6. Deflection estimation of a wind turbine blade using FBG sensors embedded in the blade bonding line

    Science.gov (United States)

    Kim, Sang-Woo; Kang, Woo-Ram; Jeong, Min-Soo; Lee, In; Kwon, Il-Bum

    2013-12-01

    Estimating the deflection of flexible composite wind turbine blades is very important to prevent the blades from hitting the tower. Several researchers have used fiber Bragg grating (FBG) sensors—a type of optical fiber sensor (OFS)—to monitor the structural behavior of the blades. They can be installed on the surface and/or embedded in the interior of composites. However, the typical installation positions of OFSs present several problems, including delamination of sensing probes and a higher risk of fiber breakage during installation. In this study, we proposed using the bonding line between the shear web and spar cap as a new installation position of embedded OFSs for estimating the deflection of the blades. Laboratory coupon tests were undertaken preliminarily to confirm the strain measuring capability of embedded FBG sensors in adhesive layers, and the obtained values were verified by comparison with results obtained by electrical strain gauges and finite element analysis. We performed static loading tests on a 100 kW composite wind turbine blade to evaluate its deflections using embedded FBG sensors positioned in the bonding line. The deflections were estimated by classical beam theory considering a rigid body rotation near the tip of the blade. The evaluated tip deflections closely matched those measured by a linear variable differential transformer. Therefore, we verified the capability of embedded FBG sensors for evaluating the deflections of wind turbine blades. In addition, we confirmed that the bonding line between the shear web and spar cap is a practical location to embed the FBG sensors.

  7. Determination of peak deflections from human surrogates using chestbands in side impact tests.

    Science.gov (United States)

    Yoganandan, Narayan; Humm, John R; Pintar, Frank A; Maiman, Dennis J

    2013-08-01

    To understand the biomechanics of the human body in motor vehicle environments, physical models including anthropomorphic test devices (ATD) and biological models (postmortem human surrogates) are used, and sled tests are conducted. Deflection is often used as a biomechanical variable to characterize the effects of impact loading and derive injury criteria. The objective of the present study was to evaluate different techniques and recommend a methodology to determine the peak thorax and abdominal deflections from temporal contours using chestbands in oblique lateral impacts. The side impact ATD WorldSID representing human surrogates was positioned on a seat. The seat was rigidly fixed to the platform of an acceleration sled. The oblique load-wall fixed to the sled consisted of separate and adjustable plates to contact the shoulder, thorax, abdomen, and pelvis. Two 59-gage chestbands were wrapped on the thorax and abdomen. Tests were conducted at low, medium, and high velocities (3.4, 6.7, and 7.5m/s) and three methods, termed the spine-sternum, bilateral, and spine-box, were used to determine the global peak deflection and its angulation. Results indicated that all three methods produced very similar angulations, for all velocity tests, and at both thorax and abdominal regions. However, maximum deflections were the lowest in the spine-sternum, followed by bilateral and spine-box methods, with one exception. Based on the development of deflection contours, locations used in the definitions of the origin, and accuracy in identifying critical locations/points in time-varying contours, results of the present study indicate that the bilateral method is the optimum procedure to determine the oblique peak deflection vector in biomechanical tests.

  8. Deflection of a liquid metal jet/drop in a tokamak environment

    Energy Technology Data Exchange (ETDEWEB)

    Pelekasis, Nikos, E-mail: pel@uth.gr [Department of Mechanical Engineering, University of Thessaly, Volos 38334 (Greece); Benos, Lefteris [Department of Mechanical Engineering, University of Thessaly, Volos 38334 (Greece); Gomes, Rui [Associação EURATOM/IST, Centro de Fusão Nuclear, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

    2014-12-15

    Highlights: • We model steady flow of a liquid metal jet inside an electromagnetic field in the presence of inertia and capillary forces. • Similar analysis is performed for the motion of a liquid metal spherical drop. • The deflection of the trajectory is predicted as a function of the intensity of the externally imposed magnetic and electric fields. • The analysis is used as a proof of principle study in reference to experimental observations of jet/drop deflection due to j{sup →}×B{sup →} effects in the ISTTOK tokamak. • We discuss the possibility of using liquid metal flows as an alternative approach toward enhancing power exhaust in tokamak facilities. - Abstract: The interaction of a liquid gallium jet with plasma has been investigated in the ISTTOK tokamak. The jet was observed to remain intact during its interaction with plasma, within a certain length beyond which drop formation was observed. Significant deflection of the jet was detected as soon as plasma production was started. Furthermore, a strong dependency of the deflection magnitude on plasma position was observed that could be correlated with plasma potential gradients. As a means to capture and, possibly, quantify this effect, a preliminary magnetohydrodynamic analysis was performed in order to predict the trajectory of a jet that is traveling inside an electromagnetic field. The effect of Lorentz forces, gravity and pressure drop are accounted for in a unidirectional model that assumes a small jet radius in comparison with the trajectory length. The effect of external electric potential gradients on jet deflection was ascertained in conjunction with the importance of electric stresses in modulating the jet speed and radius. Analysis of the results reported in the ISTTOK experiments identifies the process of jet break-up as a capillary instability. The trajectory of the ensuing droplets is modeled and intensification of the deflection process is predicted in the presence of Lorentz

  9. Tip position control of a two-link flexible robot manipulator based on nonlinear deflection feedback

    Energy Technology Data Exchange (ETDEWEB)

    Oke, G. E-mail: oke@boun.edu.tr; Istefanopulos, Y

    2003-07-01

    The control of flexible link manipulators has gained an increasing importance in robotics, in recent years. To control the tip of a flexible manipulator, the joint angles should converge to the desired positions fast and elastic deflections must be effectively suppressed. In this study, a two-link flexible manipulator is controlled by three methods and the results are compared. These methods are, Pd control, PD control augmented by a nonlinear correction term feedback, where the correction term is a function of the deflection of each link, and an adaptive fuzzy controller with the nonlinear correction term feedback. Simulations have been carried out to compare the performances of all three methods.

  10. Static deflection analysis of non prismatic multilayer p-NEMS cantilevers under electrical load

    Energy Technology Data Exchange (ETDEWEB)

    Pavithra, M., E-mail: pavithramasi78@gmail.com [PhD Research Scholar, Department of Electronics and Instrumentation, Bharathiar University, Coimbatore-46 (India); Muruganand, S. [Assistant professor, Department of Electronics and Instrumentation, Bharathiar University, Coimbatore-46 (India)

    2016-04-13

    Deflection of Euler-Bernoulli non prismatic multilayer piezoelectric nano electromechanical (p-NEMS) cantilever beams have been studied theoretically for various profiles of p-NEMS cantilevers by applying the electrical load. This problem has been answered by applying the boundary conditions derived by simple polynomials. This method is applied for various profiles like rectangular and trapezoidal by varying the thickness of the piezoelectric layer as well as the material. The obtained results provide the better deflection for trapezoidal profile with ZnO piezo electric layer of suitable nano cantilevers for nano scale applications.

  11. Probability-based method using RFEM for predicting wall deflection caused by excavation

    Institute of Scientific and Technical Information of China (English)

    Yu-geng TANG

    2011-01-01

    This study employs the random finite element method (RFEM) to analyze the wall deflection caused by excavation.The RFEM combined random fields of material properties with the FEM through the Monte Carlo simulation.A well-documented excavation case history is employed to evaluate the influence of uncertainty of analysis parameters.This study shows that RFEM can provide reasonable estimations of the exceedance probability of wall deflection caused by excavation,and has the potential to be a useful tool to account for the uncertainties of material and model parameters in the numerical analysis.

  12. Orbital Simulations on Deflecting Near-Earth Objects by Directed Energy

    OpenAIRE

    Zhang, Qicheng; Walsh, Kevin J.; Melis, Carl; Hughes, Gary B.; Lubin, Philip M.

    2016-01-01

    Laser ablation of a Near-Earth Object (NEO) on a collision course with Earth produces a cloud of ejecta which exerts a thrust on the NEO, deflecting it from its original trajectory. Ablation may be performed from afar by illuminating an Earth-targeting asteroid or comet with a stand-off "DE- STAR" system consisting of a large phased-array laser in Earth orbit. Alternatively, a much smaller stand-on "DE-STARLITE" system may travel alongside the target, slowly deflecting it from nearby over a l...

  13. Stern-Gerlach deflection of field-free aligned paramagnetic molecules

    CERN Document Server

    Gershnabel, E; Averbukh, I Sh

    2011-01-01

    The effects of laser-induced prealignment on the deflection of paramagnetic molecules by inhomogeneous static magnetic field are studied. Depending on the relevant Hund's coupling case of the molecule, two different effects were identified: either suppression of the deflection by laser pulses (Hund's coupling case (a) molecules, such as ClO), or a dramatic reconstruction of the broad distribution of the scattering angles into several narrow peaks (for Hund's coupling case (b) molecules, such as O2 or NH). These findings are important for various applications using molecular guiding, focusing and trapping with the help of magnetic fields.

  14. A Novel Deflection Method for Measuring the Growth Stress of Thermally Growing Oxide Scales

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A kind of new deflection technique has been developed for measuring the growth stress of thermally growing oxide scales duringhigh temperature oxidation of alloys. The average growth stresses in oxide scales such as Al2O3, NiO and Cr2O3 formed onthe surface of the superalloys can be investigated by this technique. Unlike the comventional deflection method, the novelmethod does not need to apply a coating for preventing one main face of thin strip specimen from oxidizing and can be usedunaer tne condition of longer time and higher temperature.

  15. Wind tunnel testing of a closed-loop wake deflection controller for wind farm power maximization

    Science.gov (United States)

    Campagnolo, Filippo; Petrović, Vlaho; Schreiber, Johannes; Nanos, Emmanouil M.; Croce, Alessandro; Bottasso, Carlo L.

    2016-09-01

    This paper presents results from wind tunnel tests aimed at evaluating a closed- loop wind farm controller for wind farm power maximization by wake deflection. Experiments are conducted in a large boundary layer wind tunnel, using three servo-actuated and sensorized wind turbine scaled models. First, we characterize the impact on steady-state power output of wake deflection, achieved by yawing the upstream wind turbines. Next, we illustrate the capability of the proposed wind farm controller to dynamically driving the upstream wind turbines to the optimal yaw misalignment setting.

  16. Laser-driven deflection arrangements and methods involving charged particle beams

    Science.gov (United States)

    Plettner, Tomas [San Ramon, CA; Byer, Robert L [Stanford, CA

    2011-08-09

    Systems, methods, devices and apparatus are implemented for producing controllable charged particle beams. In one implementation, an apparatus provides a deflection force to a charged particle beam. A source produces an electromagnetic wave. A structure, that is substantially transparent to the electromagnetic wave, includes a physical structure having a repeating pattern with a period L and a tilted angle .alpha., relative to a direction of travel of the charged particle beam, the pattern affects the force of the electromagnetic wave upon the charged particle beam. A direction device introduces the electromagnetic wave to the structure to provide a phase-synchronous deflection force to the charged particle beam.

  17. Control of deflection deformation of plate-shape castings in solidification

    Institute of Scientific and Technical Information of China (English)

    郑贤淑; 金英达

    2003-01-01

    The deformation mechanism during the solidification was analyzed based on the experimental results ofthe castings. An approximate quadratic differential equation and its discrete model of calculation deflection were pro-posed. The model indicates that the key factors leading to the deflection deformation are the thermal bending mo-ment M and the flexural rigidity E.J. The smaller the former and the larger the latter is, the smaller the deflectiondeformation will be. The experiments are carried out at various technical conditions, and their results appear good a-greement with calculation ones. A method was proposed to predict and control the casting deformation.

  18. In Situ Characterization of the Local Work Function along Individual Free Standing Nanowire by Electrostatic Deflection.

    Science.gov (United States)

    Chen, Yicong; Zhao, Chengchun; Huang, Feng; Zhan, Runze; Deng, Shaozhi; Xu, Ningsheng; Chen, Jun

    2016-02-17

    In situ characterization of the work function of quasi one dimensional nanomaterials is essential for exploring their applications. Here we proposed to use the electrostatic deflection induced by work function difference between nanoprobe and nanowire for in situ measuring the local work function along a free standing nanowire. The physical mechanism for the measurement was discussed in details and a parabolic relationship between the deflection and the potential difference was derived. As a demonstration, measurement of the local work functions on the tip and the sidewall of a ZnO nanowire with Au catalyst at its end and a LaB6 nanowire have been achieved with good accuracy.

  19. Deflection of 450 GeV protons by planar channeling in a bent silicon crystal

    Science.gov (United States)

    Jensen, B. N.; Møller, S. P.; Uggerhøj, E.; Worm, T.; Atherton, H. W.; Clément, M.; Doble, N.; Elsener, K.; Gatignon, L.; Grafström, P.; Jeanneret, J. B.; Hage-Ali, M.; Siffert, P.

    1992-08-01

    A 450 GeV proton beam has been bent by various angles from 4 to 14 mrad using planar channeling in a (111) silicon crystal. Detailed investigations of the deflected beam as well as the unbent and scattered particles have been performed. The incident beam had a divergence of about 35 μrad (FWHM). 20% of the protons hitting the crystal front face were found to be initially channeled. The measured bending efficiencies range from 5 to 2% (for increasing deflection angles) are compared to theoretical estimates including surface acceptance and dechanneling in bent silicon crystals.

  20. Deflection of 450 GeV protons by planar channeling in a bent silicon crystal

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, B.N.; Moeller, S.P.; Uggerhoej, E.; Worm, T. (Inst. for Synchrotron Radiation, Aarhus Univ. (Denmark)); Atherton, H.W.; Clement, M.; Doble, N.; Elsener, K.; Gatignon, L.; Grafstroem, P.; Jeanneret, J.B. (European Organization for Nuclear Research (CERN), Geneva (Switzerland)); Hage-Ali, M.; Siffert, P. (Centre de Recherches Nucleaires, 67 - Strasbourg (France))

    1992-08-01

    A 450 GeV proton beam has been bent by various angles from 4 to 14 mrad using planar channeling in a (111) silicon crystal. Detailed investigations of the deflected beam as well as the unbent and scattered particles have been performed. The incident beam had a divergence of about 35 [mu]rad (FWHM). 20% of the protons hitting the crystal front face were found to be initially channeled. The measured bending efficiencies range from 5 to 2% (for increasing deflection angles) and are compared to theoretical estimates including surface acceptance and dechanneling in bent silicon crystals. (orig.).

  1. Analysis of HOM Properties of Superconducting Parallel-Bar Deflecting/Crabbing Cavities

    Energy Technology Data Exchange (ETDEWEB)

    S.U. De Silva, J.R. Delayen

    2011-07-01

    The superconducting parallel-bar cavity is currently being considered for a number of deflecting and crabbing applications due to improved properties and compact design geometries. The 499 MHz deflecting cavity proposed for the Jefferson Lab 12 GeV upgrade and the 400 MHz crab cavity for the proposed LHC luminosity upgrade are two of the major applications. For high current applications the higher order modes must be damped to acceptable levels to eliminate any beam instabilities. The frequencies and R/Q of the HOMs and mode separation are evaluated and compared for different parallel-bar cavity designs.

  2. The ellipsoidal corrections for boundary value problems of deflection of the vertical with ellipsoid boundary

    Directory of Open Access Journals (Sweden)

    Xiangchao Meng

    2017-07-01

    Full Text Available The boundary value problem of deflections of vertical with ellipsoid boundary is studied in the paper. Based on spherical harmonic series, the ellipsoidal corrections for the boundary value problem are derived so that it can be well solved. In addition, an imitation arithmetic is given for examining the accuracies of solutions for the boundary value problem as well as its spherical approximation problem, and the computational results illustrate that the boundary value problem has higher accuracy than its spherical approximation problem if deflection of the vertical are measured on geoid.

  3. Comparison between Deflection and Vibration Characteristics of Rectangular and Trapezoidal profile Microcantilevers

    Directory of Open Access Journals (Sweden)

    Booun Bang

    2009-04-01

    Full Text Available Arrays of microcantilevers are increasingly being used as physical, biological, and chemical sensors in various applications. To improve the sensitivity of microcantilever sensors, this study analyses and compares the deflection and vibration characteristics of rectangular and trapezoidal profile microcantilevers. Three models of each profile are investigated. The cantilevers are analyzed for maximum deflection, fundamental resonant frequency and maximum stress. The surface stress is modelled as in-plane tensile force applied on the top edge of the microcantilevers. A commercial finite element analysis software ANSYS is used to analyze the designs. Results show paddled trapezoidal profile microcantilevers have better sensitivity.

  4. Features of the galactic magnetic field regarding deflections of ultra-high-energy cosmic rays

    Energy Technology Data Exchange (ETDEWEB)

    Wirtz, Marcus; Erdmann, Martin; Mueller, Gero; Urban, Martin [III. Physikalisches Institut A, RWTH Aachen University (Germany)

    2016-07-01

    Most recent models of the galactic magnetic field have been derived from Faraday rotation measurements and imply strong deflections even for ultra-high energy cosmic rays. We investigate the characteristics of the different field parametrizations and point out similarities and interesting features. Among them are extragalactic regions which are invisible for an Earth bound observation and the transition from diffuse to ballistic behaviour in the 1 EeV energy regime. Applying this knowledge to a directional analysis, there are indications for deflection patterns by the galactic magnetic field in cosmic ray arrival directions measured by the Pierre Auger Observatory.

  5. Vibrational spectroscopy

    Science.gov (United States)

    Umesh P. Agarwal; Rajai Atalla

    2010-01-01

    Vibrational spectroscopy is an important tool in modern chemistry. In the past two decades, thanks to significant improvements in instrumentation and the development of new interpretive tools, it has become increasingly important for studies of lignin. This chapter presents the three important instrumental methods-Raman spectroscopy, infrared (IR) spectroscopy, and...

  6. Analisis Struktur Balok Non Prismatis Menggunakan Metode Persamaan Slope – Deflection

    Directory of Open Access Journals (Sweden)

    Agus Setiawan

    2011-12-01

    Full Text Available Slope – deflection equation method is an analysis method to solve statically indeterminate structure. This method is a simple technique to analyze continuous beam, either prismatic or non prismatic. The technique for analyzing non prismatic beam is based on the prismatic beam concept, but with the introduce of some modification coefficient. These coefficients are available in some textbook discussing about structural analysis. This research has an objective to compare the analysis result of a continuous non prismatic beam, with slope – deflection equation method, and result from a structural analysis program (i.e. SAP 2000 v.11.00. The internal moment at the joints produced from this two method will be compared each other. The results show that there is a small difference resulted in internal moment, obtained from hand calculation with slope – deflection method and from software output. The differences resulted from this two techniques are 2 up to 6%. Based on this result it can be stated that slope-deflection method can be used to analyze statically indeterminate nonprismatic beam with some modification factors. The result obtained is nearly the same with one obtained from commercial softwares. 

  7. Comparative research on the methods for measuring the mode deflection angle of cylindrical resonator gyroscope

    Science.gov (United States)

    Wang, Kai; Fan, Zhenfang; Wang, Dongya; Wang, Yanyan; Pan, Yao; Qu, Tianliang; Xu, Guangming

    2016-10-01

    The existence of mode deflection angle in the cylindrical resonator gyroscope (CRG) leads to the signal drift on the detecting nodes of the gyro vibration and significantly decreases the performance of the CRG. Measuring the mode deflection angle efficiently is the foundation of tuning for the imperfect cylindrical shell resonator. In this paper, an optical method based on the measuring gyroscopic resonator's vibration amplitude with the laser Doppler vibrometer and an electrical method based on measuring the output voltage of the electrodes on the resonator are both presented to measure the mode deflection angle. Comparative experiments were implemented to verify the methodology and the results show that both of the two methods could recognize the mode deflection angle efficiently. The precision of the optical method relies on the number and position of testing points distributed on the resonator. The electrical method with simple circuit shows high accuracy of measuring in a less time compared to the optical method and its error source arises from the influence of circuit noise as well as the inconsistent distribution of the piezoelectric electrodes.

  8. Die casting die deflections: Prediction and attenuation. Final report, July 1, 1995--September 30, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Miller, R.A.; Ahuett-Garza, H.; Choudhury, A.K.; Dedhia, S.

    1998-05-01

    This report summarizes two years of research intended to develop methods to model and predict the deflection patterns in die casting dies. No comprehensive analysis of this type had previously been completed. The die casting process is complex and involves numerous mechanical and thermal phenomena that effect the mechanical behavior of the die. A critical activity in this work was sorting out and evaluating the relative contributions of the various mechanisms to die deflections. This evaluation was accomplished through a series of simple engineering analyses based primarily on the order of magnitude of the influence of each load considered on die deflections. A modeling approach incorporating commercially available finite element analysis software was developed and tested. The model evolved by testing simple models against more comprehensive models and against the limited experimental data that is available. The development of the modeling approach lead to consideration of the die casting machine in more detail than was originally anticipated. The machine is critical and cannot be ignored. A simplified model described as a spring/platen model was developed to account for the machine platens, tie bars, and toggles. The characteristics of this model are described and predictions based on this model are compared against full machine models and measured deflections of machine platens. Details of the modeling approach and the various case studies are provided in the report and in several publications that have resulted from the work.

  9. DEFLECTION OF A HETEROGENEOUS WIDE-BEAM UNDER UNIFORM PRESSURE LOAD

    Energy Technology Data Exchange (ETDEWEB)

    T. V. Holschuh; T. K. Howard; W. R. Marcum

    2014-07-01

    Oregon State University (OSU) and the Idaho National Laboratory (INL) are currently collaborating on a test program which entails hydro-mechanical testing of a generic plate type fuel element, or generic test plate assembly (GTPA), for the purpose of qualitatively demonstrating mechanical integrity of uranium-molybdenum monolithic plates as compared to that of uranium aluminum dispersion, and aluminum fuel plates onset by hydraulic forces. This test program supports ongoing work conducted for/by the Global Threat Reduction Initiative (GTRI) Fuels Development Program. This study’s focus supports the ongoing collaborative effort by detailing the derivation of an analytic solution for deflection of a heterogeneous plate under a uniform, distributed load in order to predict the deflection of test plates in the GTPA. The resulting analytical solutions for three specific boundary condition sets are then presented against several test cases of a homogeneous plate. In all test cases considered, the results for both homogeneous and heterogeneous plates are numerically identical to one another, demonstrating correct derivation of the heterogeneous solution. Two additional problems are presents herein that provide a representative deflection profile for the plates under consideration within the GTPA. Furthermore, qualitative observations are made about the influence of a more-rigid internal fuel-meat region and its influence on the overall deflection profile of a plate. Present work is being directed to experimentally confirm the analytical solution’s results using select materials.

  10. Systematic characterization of optical beam deflection measurement system for micro and nanomechanical systems

    NARCIS (Netherlands)

    Herfst, R.W.; Klop, W.A.; Eschen, M.; Dool, T.C. van den; Koster, N.B.; Sadeghian Marnani, H.

    2014-01-01

    Optical beam deflection (OBD) measurement method is very popular in various types of scanning probe microscopy (SPM) and micro/nanomechanical sensors to measure a mechanical motion. This paper reports the detail design and implementation of a very low drift (2 nm over 1000 s), high bandwidth (40 MHz

  11. Experimental and numerical study on vibrations and static deflection of a thin hyperelastic plate

    Science.gov (United States)

    Amabili, Marco; Balasubramanian, Prabakaran; Breslavsky, Ivan D.; Ferrari, Giovanni; Garziera, Rinaldo; Riabova, Kseniia

    2016-12-01

    The hyperelastic behavior of a thin square silicone rubber plate has been investigated analytically, numerically and experimentally; the case of small-amplitude vibrations has been considered, as well as the case of large static deflection under aerostatic pressure. The Mooney-Rivlin hyperelastic model has been chosen to describe the material nonlinear elasticity. The material parameters have been identified by a fitting procedure on the results of a uniaxial traction test. For the analytical model, the equations of motion have been obtained by a unified energy approach, and geometrical nonlinearities are modeled according to the Novozhilov nonlinear shell theory. A numerical model has also been developed by using a commercial Finite-Element code. In the experiments, the silicone rubber plate has been fixed to a heavy metal frame; a certain in-plane pre-load, applied by stretching the plate, has been given in order to ensure a flatness of the surface. An experimental modal analysis has been conducted; results have been used to identify the applied in-plane loads by optimization procedure with two different models: a numerical and an analytical one. The first four experimental and numerical natural modes and frequencies are in good agreement with the experiments after the pre-load identification. The static deflection has been measured experimentally for different pressures. Results have been compared to those obtained by analytical and numerical models. The static deflections are also satisfactorily compared, up to a deflection 50 times larger than the plate thickness, corresponding to a 30 percent strain.

  12. Large-deflection statics analysis of active cardiac catheters through co-rotational modelling.

    Science.gov (United States)

    Peng Qi; Chen Qiu; Mehndiratta, Aadarsh; I-Ming Chen; Haoyong Yu

    2016-08-01

    This paper presents a co-rotational concept for large-deflection formulation of cardiac catheters. Using this approach, the catheter is first discretized with a number of equal length beam elements and nodes, and the rigid body motions of an individual beam element are separated from its deformations. Therefore, it is adequate for modelling arbitrarily large deflections of a catheter with linear elastic analysis at the local element level. A novel design of active cardiac catheter of 9 Fr in diameter at the beginning of the paper is proposed, which is based on the contra-rotating double helix patterns and is improved from the previous prototypes. The modelling section is followed by MATLAB simulations of various deflections when the catheter is exerted different types of loads. This proves the feasibility of the presented modelling approach. To the best knowledge of the authors, it is the first to utilize this methodology for large-deflection static analysis of the catheter, which will enable more accurate control of robot-assisted cardiac catheterization procedures. Future work would include further experimental validations.

  13. Deflection-based method for seismic response analysis of concrete walls: Benchmarking of CAMUS experiment

    Energy Technology Data Exchange (ETDEWEB)

    Basu, Prabir C. [Civil and Structural Engineering Division, Atomic Energy Regulatory Board (India)]. E-mail: pcb@aerb.gov.in; Roshan, A.D. [Civil and Structural Engineering Division, Atomic Energy Regulatory Board (India)

    2007-07-15

    A number of shake table tests had been conducted on the scaled down model of a concrete wall as part of CAMUS experiment. The experiments were conducted between 1996 and 1998 in the CEA facilities in Saclay, France. Benchmarking of CAMUS experiments was undertaken as a part of the coordinated research program on 'Safety Significance of Near-Field Earthquakes' organised by International Atomic Energy Agency (IAEA). Technique of deflection-based method was adopted for benchmarking exercise. Non-linear static procedure of deflection-based method has two basic steps: pushover analysis, and determination of target displacement or performance point. Pushover analysis is an analytical procedure to assess the capacity to withstand seismic loading effect that a structural system can offer considering the redundancies and inelastic deformation. Outcome of a pushover analysis is the plot of force-displacement (base shear-top/roof displacement) curve of the structure. This is obtained by step-by-step non-linear static analysis of the structure with increasing value of load. The second step is to determine target displacement, which is also known as performance point. The target displacement is the likely maximum displacement of the structure due to a specified seismic input motion. Established procedures, FEMA-273 and ATC-40, are available to determine this maximum deflection. The responses of CAMUS test specimen are determined by deflection-based method and analytically calculated values compare well with the test results.

  14. Temperature- and deflection- dependences of orthodontic force with Ni-Ti wires.

    Science.gov (United States)

    Yanaru, Kotaro; Yamaguchi, Kazunori; Kakigawa, Hiroshi; Kozono, Yoshio

    2003-06-01

    Orthodontic forces of Ni-Ti wires examined under the retrained condition on the dental arch model were evaluated with the changes in temperature and deflection. The tested specimens were a commercially available superelastic (W1) wire and two shape memory wires with their nominal A(f) points were 35 degrees C (W2) and 40 degrees C (W3), respectively. They showed typical superelastic hysteresis loops under the restraint condition at 40 degrees C. The force levels were significantly larger than those generally obtained by simple three-bending test. The recovery forces in the plateau region at 1.0 mm deflection were much larger than desired in the clinical guidelines around oral temperatures. In the shape memory wire W3, the recovery force rapidly decreased to zero by a small reduction of the deflection from its maximum. However, the wire again exerted the force with the remaining permanent deflection by temperature rising. It was small compared to the guidelines of desirable orthodontic force and seemed to be useful especially for the hypersensitive patients.

  15. Deflection of a vibrissa leads to a gradient of strain across mechanoreceptors in a mystacial follicle.

    Science.gov (United States)

    Whiteley, Samuel J; Knutsen, Per M; Matthews, David W; Kleinfeld, David

    2015-07-01

    Rodents use their vibrissae to detect and discriminate tactile features during active exploration. The site of mechanical transduction in the vibrissa sensorimotor system is the follicle sinus complex and its associated vibrissa. We study the mechanics within the ring sinus (RS) of the follicle in an ex vivo preparation of the mouse mystacial pad. The sinus region has a relatively dense representation of Merkel mechanoreceptors and longitudinal lanceolate endings. Two-photon laser-scanning microscopy was used to visualize labeled cell nuclei in an ∼ 100-nl vol before and after passive deflection of a vibrissa, which results in localized displacements of the mechanoreceptor cells, primarily in the radial and polar directions about the vibrissa. These displacements are used to compute the strain field across the follicle in response to the deflection. We observe compression in the lower region of the RS, whereas dilation, with lower magnitude, occurs in the upper region, with volumetric strain ΔV/V ∼ 0.01 for a 10° deflection. The extrapolated strain for a 0.1° deflection, the minimum angle that is reported to initiate a spike by primary neurons, corresponds to the minimum strain that activates Piezo2 mechanoreceptor channels.

  16. A load balancing bufferless deflection router for network-on-chip

    Science.gov (United States)

    Xiaofeng, Zhou; Zhangming, Zhu; Duan, Zhou

    2016-07-01

    The bufferless router emerges as an interesting option for cost-efficient in network-on-chip (NoC) design. However, the bufferless router only works well under low network load because deflection more easily occurs as the injection rate increases. In this paper, we propose a load balancing bufferless deflection router (LBBDR) for NoC that relieves the effect of deflection in bufferless NoC. The proposed LBBDR employs a balance toggle identifier in the source router to control the initial routing direction of X or Y for a flit in the network. Based on this mechanism, the flit is routed according to XY or YX routing in the network afterward. When two or more flits contend the same one desired output port a priority policy called nearer-first is used to address output ports allocation contention. Simulation results show that the proposed LBBDR yields an improvement of routing performance over the reported bufferless routing in the flit deflection rate, average packet latency and throughput by up to 13%, 10% and 6% respectively. The layout area and power consumption compared with the reported schemes are 12% and 7% less respectively. Project supported by the National Natural Science Foundation of China (Nos. 61474087, 61322405, 61376039).

  17. Systematic characterization of optical beam deflection measurement system for micro and nanomechanical systems

    NARCIS (Netherlands)

    Herfst, R.W.; Klop, W.A.; Eschen, M.; Dool, T.C. van den; Koster, N.B.; Sadeghian Marnani, H.

    2014-01-01

    Optical beam deflection (OBD) measurement method is very popular in various types of scanning probe microscopy (SPM) and micro/nanomechanical sensors to measure a mechanical motion. This paper reports the detail design and implementation of a very low drift (2 nm over 1000 s), high bandwidth (40

  18. Marginal eyespots on butterfly wings deflect bird attacks under low light intensities with UV wavelengths.

    Directory of Open Access Journals (Sweden)

    Martin Olofsson

    Full Text Available BACKGROUND: Predators preferentially attack vital body parts to avoid prey escape. Consequently, prey adaptations that make predators attack less crucial body parts are expected to evolve. Marginal eyespots on butterfly wings have long been thought to have this deflective, but hitherto undemonstrated function. METHODOLOGY/PRINCIPAL FINDINGS: Here we report that a butterfly, Lopinga achine, with broad-spectrum reflective white scales in its marginal eyespot pupils deceives a generalist avian predator, the blue tit, to attack the marginal eyespots, but only under particular conditions-in our experiments, low light intensities with a prominent UV component. Under high light intensity conditions with a similar UV component, and at low light intensities without UV, blue tits directed attacks towards the butterfly head. CONCLUSIONS/SIGNIFICANCE: In nature, birds typically forage intensively at early dawn, when the light environment shifts to shorter wavelengths, and the contrast between the eyespot pupils and the background increases. Among butterflies, deflecting attacks is likely to be particularly important at dawn when low ambient temperatures make escape by flight impossible, and when insectivorous birds typically initiate another day's search for food. Our finding that the deflective function of eyespots is highly dependent on the ambient light environment helps explain why previous attempts have provided little support for the deflective role of marginal eyespots, and we hypothesize that the mechanism that we have discovered in our experiments in a laboratory setting may function also in nature when birds forage on resting butterflies under low light intensities.

  19. Integrating deflection models and image feedback for real-time flexible needle steering

    NARCIS (Netherlands)

    Abayazid, Momen; Roesthuis, Roy; Reilink, Rob; Misra, Sarthak

    2013-01-01

    Needle insertion procedures are commonly used for diagnostic and therapeutic purposes. In this paper, an image- guided control system is developed to robotically steer flexible nee- dles with an asymmetric tip. Knowledge about needle deflection is required for accurate steering. Two different models

  20. Integrating deflection models and image feedback for real-time flexible needle steering

    NARCIS (Netherlands)

    Abayazid, Momen; Roesthuis, Roy J.; Reilink, Rob; Misra, Sarthak

    2012-01-01

    Needle insertion procedures are commonly used for diagnostic and therapeutic purposes. In this paper, an image- guided control system is developed to robotically steer flexible nee- dles with an asymmetric tip. Knowledge about needle deflection is required for accurate steering. Two different models

  1. Beam deflection induced by E×B near a linear filament cathode

    Science.gov (United States)

    Zhang, Huashun; Jiang, Jiasheng

    2017-02-01

    Beam deflection induced by E×B near a linear filament cathode in a two grid electron gun is presented theoretically and experimentally. The experimental results are consistent with the calculation based on the theoretical equations. The influences upon performance and design of electron gun with linear filament cathode, which is used broadly in electrocurtain accelerators, are discussed in detail.

  2. Dealing with Uncertainties in Asteroid Deflection Demonstration Missions: NEOTwIST

    CERN Document Server

    Eggl, Siegfried; Cano, Juan L; Avila, Javier Martin; Drube, Line; Harris, Alan W; Falke, Albert; Johann, Ulrich; Engel, Kilian; Schwartz, Stephen R; Michel, Patrick

    2016-01-01

    Deflection missions to near-Earth asteroids will encounter non-negligible uncertainties in the physical and orbital parameters of the target object. In order to reliably assess future impact threat mitigation operations such uncertainties have to be quantified and incorporated into the mission design. The implementation of deflection demonstration missions offers the great opportunity to test our current understanding of deflection relevant uncertainties and their consequences, e.g., regarding kinetic impacts on asteroid surfaces. In this contribution, we discuss the role of uncertainties in the NEOTwIST asteroid deflection demonstration concept, a low-cost kinetic impactor design elaborated in the framework of the NEOShield project. The aim of NEOTwIST is to change the spin state of a known and well characterized near-Earth object, in this case the asteroid (25143) Itokawa. Fast events such as the production of the impact crater and ejecta are studied via cube-sat chasers and a flyby vehicle. Long term chang...

  3. Crack deflection in brittle media with heterogeneous interfaces and its application in shale fracking

    Science.gov (United States)

    Zeng, Xiaguang; Wei, Yujie

    Driven by the rapid progress in exploiting unconventional energy resources such as shale gas, there is growing interest in hydraulic fracture of brittle yet heterogeneous shales. In particular, how hydraulic cracks interact with natural weak zones in sedimentary rocks to form permeable cracking networks is of significance in engineering practice. Such a process is typically influenced by crack deflection, material anisotropy, crack-surface friction, crustal stresses, and so on. In this work, we extend the He-Hutchinson theory (He and Hutchinson, 1989) to give the closed-form formulae of the strain energy release rate of a hydraulic crack with arbitrary angles with respect to the crustal stress. The critical conditions in which the hydraulic crack deflects into weak interfaces and exhibits a dependence on crack-surface friction and crustal stress anisotropy are given in explicit formulae. We reveal analytically that, with increasing pressure, hydraulic fracture in shales may sequentially undergo friction locking, mode II fracture, and mixed mode fracture. Mode II fracture dominates the hydraulic fracturing process and the impinging angle between the hydraulic crack and the weak interface is the determining factor that accounts for crack deflection; the lower friction coefficient between cracked planes and the greater crustal stress difference favor hydraulic fracturing. In addition to shale fracking, the analytical solution of crack deflection could be used in failure analysis of other brittle media.

  4. Hydroelastic analysis of a very large floating plate with large deflections in stochastic seaway

    DEFF Research Database (Denmark)

    Chen, Xu-jun; Jensen, Jørgen Juncher; Cui, Wei-cheng

    2004-01-01

    The hydroelasticity of a very large floating plate with large deflections in multidirectional irregular waves is discussed. After a brief introduction on wave loads on a flexible structure, the paper derives the generalised fluid force acting on a floating structure in multidirectional irregular ...

  5. Asteroid Impact and Deflection Assessment mission: the Double Asteroid Redirection Test (DART)

    Science.gov (United States)

    Cheng, A.; Michel, P.

    2015-10-01

    The Asteroid Impact & Deflection Assessment (AIDA) mission will be the first space experiment to demonstrate asteroid impact hazard mitigation by using a kinetic impactor. AIDA is a joint ESA-NASA cooperative project, which includes the ESA Asteroid Impact Mission (AIM) rendezvous spacecraft and the NASA Double Asteroid Redirection Test (DART) mission. The AIDA target is the near-Earth binary asteroid 65803 Didymos, which will make an unusually close approach to Earth in October, 2022. The ~300-kg DART spacecraft is designed to impact the Didymos secondary at 6.5 km/s and demonstrate the ability to modify its trajectory through momentum transfer. The primary goals of AIDA are (i) to investigate the binary near-Earth asteroid (65803) Didymos, (ii) to demonstrate asteroid deflection by kinetic impact and to characterize the deflection. The primary DART objectives are to demonstrate a hypervelocity impact on the Didymos moon and to determine the resulting deflection from ground-based observatories. The DART impact on the Didymos secondary will cause a measurable change in the orbital period of the binary.

  6. Wide-Band Optical Fibre System for Investigation of MEMS and NEMS Deflection

    Directory of Open Access Journals (Sweden)

    Orłowska Karolina

    2014-08-01

    Full Text Available In this work the construction of experimental setup for MEMS/NEMS deflection measurements is presented. The system is based on intensity fibre optic detector for linear displacement sensing. Furthermore the electronic devices: current source for driving the light source and photodetector with wide-band preamplifier are presented.

  7. Deflection monitoring for a box girder based on a modified conjugate beam method

    Science.gov (United States)

    Chen, Shi-Zhi; Wu, Gang; Xing, Tuo

    2017-08-01

    After several years of operation, a box girder bridge would commonly experience excessive deflection, which endangers the bridge’s life span as well as the safety of vehicles travelling on it. In order to avoid potential risks, it is essential to constantly monitor the defection of box girders. However, currently, the direct deflection monitoring methods are limited by the complicated environments beneath the bridges, such as rivers or other traffic lanes, which severely impede the layouts of the sensors. The other indirect deflection monitoring methods mostly do not thoroughly consider the inherent shear lag effect and shear deformation in the box girder, resulting in a rather large error. Under these circumstances, a deflection monitoring method suiting box girders is proposed in this article, based on the conjugate beam method and distributed long-gauge fibre Bragg grating (FBG) sensor. A lab experiment was conducted to verify the reliability and feasibility of this method under practical application. Further, the serviceability under different span-depth ratios and web thicknesses was examined through a finite element model.

  8. Terahertz spectroscopy

    DEFF Research Database (Denmark)

    Jepsen, Peter Uhd

    2009-01-01

    In this presentation I will review methods for spectroscopy in the THz range, with special emphasis on the practical implementation of the technique known ad THz time-domain spectroscopy (THz-TDS). THz-TDS has revived the old field of far-infrared spectroscopy, and enabled a wealth of new...... activities that promise commercial potential for spectroscopic applications in the THz range. This will be illustrated with examples of spectroscopy of liquids inside their bottles as well as sensitive, quantitative spectroscopy in waveguides....

  9. ON THE EVALUATION OF DEFLECTIONS OF THE VERTICAL USING FFT TECHNIQUE

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    There exist three types of convolution formulae for the efficientevaluation of gravity field convolution integrals,i.e.,the planar 2D convolution,the spherical 2D convolution and the spherical 1D convolution.The largest drawback of both the planar and the spherical 2D FFT methods is that,due to the approximations in the kernel function,only inexact results can be achieved.Apparently,the reason is the meridian convergence at higher latitudes.As the meridians converge,the Δφ,Δλ blocks do not form a rectangular grid,as is assumed in 2D FFT methods.It should be pointed out that the meridian convergence not only leads to an approximation error in the kernel function,but also causes an approximation error during the implementation of 2D FFT in computer.In order to meet the increasing need for precise determination of the vertical deflections,this paper derives a more precise planar 2D FFT formula for the computation of the vertical deflections.After having made a detailed comparison between the planar and the spherical 2D FFT formulae,we find out the main source of errors causing the loss in accuracy by applying the conventional spherical 2D FFT method.And then,a modified spherical 2D FFT formula for the computation of the vertical deflections is developed in this paper.A series of numerical tests have been carried out to illustrate the improvement made upon the old spherical 2D FFT.The second part of this paper is to discuss the influences of the spherical harmonic reference field,the limited capsize,and the singular integral on the computation of the vertical deflections.The results of the vertical deflections over China by applying the spherical 1D FFT formula with different integration radii have been compared to the astro-observed vertical deflections in the South China Sea to obtain a set of optimum deflection computation parameters.

  10. Comparison of the Load Deflection Characteristics of Esthetic and Metal Orthodontic Wires on Ceramic Brackets using Three Point Bending Test

    Directory of Open Access Journals (Sweden)

    Umal Hiralal Doshi

    2013-01-01

    Conclusion: Steel wires showed highest strength values, requiring the incorporation of loops and folds to reduce the load/deflection. NiTi and GFRPC wires produced more deflection at low levels of force, however the esthetic wire was shown to fracture and break.

  11. Cuspal deflection and microleakage in premolar teeth restored with bulk-fill flowable resin-based composite base materials

    DEFF Research Database (Denmark)

    Moorthy, A; Hogg, C H; Dowling, A H;

    2012-01-01

    To assess the cuspal deflection and cervical microleakage of standardised Class II cavities incrementally filled with a dimethacrylate RBC or bulk-fill flowable RBC bases.......To assess the cuspal deflection and cervical microleakage of standardised Class II cavities incrementally filled with a dimethacrylate RBC or bulk-fill flowable RBC bases....

  12. A geometrically non-linear formulation of a three-dimensional beam element for solving large deflection multibody system problems

    NARCIS (Netherlands)

    Jonker, J.B.; Meijaard, J.P.

    2013-01-01

    A beam finite element formulation for large deflection problems in the analysis of flexible multibody systems has been proposed. In this formulation, a set of independent discrete deformation modes are defined for each element which are related to conventional small deflection beam theory in a co-ro

  13. Application of artificial neural networks to predict the deflections of reinforced concrete beams

    Science.gov (United States)

    Kaczmarek, Mateusz; Szymańska, Agnieszka

    2016-06-01

    Nonlinear structural mechanics should be taken into account in the practical design of reinforced concrete structures. Cracking is one of the major sources of nonlinearity. Description of deflection of reinforced concrete elements is a computational problem, mainly because of the difficulties in modelling the nonlinear stress-strain relationship of concrete and steel. In design practise, in accordance with technical rules (e.g., Eurocode 2), a simplified approach for reinforced concrete is used, but the results of simplified calculations differ from the results of experimental studies. Artificial neural network is a versatile modelling tool capable of making predictions of values that are difficult to obtain in numerical analysis. This paper describes the creation and operation of a neural network for making predictions of deflections of reinforced concrete beams at different load levels. In order to obtain a database of results, that is necessary for training and testing the neural network, a research on measurement of deflections in reinforced concrete beams was conducted by the authors in the Certified Research Laboratory of the Building Engineering Institute at Wrocław University of Science and Technology. The use of artificial neural networks is an innovation and an alternative to traditional methods of solving the problem of calculating the deflections of reinforced concrete elements. The results show the effectiveness of using artificial neural network for predicting the deflection of reinforced concrete beams, compared with the results of calculations conducted in accordance with Eurocode 2. The neural network model presented in this paper can acquire new data and be used for further analysis, with availability of more research results.

  14. Nanosecond pulsed laser ablation of Ge investigated by employing photoacoustic deflection technique and SEM analysis

    Energy Technology Data Exchange (ETDEWEB)

    Yaseen, Nazish; Bashir, Shazia; Shabbir, Muhammad Kaif; Jalil, Sohail Abdul; Akram, Mahreen; Hayat, Asma; Mahmood, Khaliq; Haq, Faizan-ul; Ahmad, Riaz; Hussain, Tousif

    2016-06-01

    Nanosecond pulsed laser ablation phenomena of single crystal Ge (100) has been investigated by employing photoacoustic deflection as well as SEM analysis techniques. Nd: YAG laser (1064 nm, 10 ns, 1–10 Hz) at various laser fluences ranging from 0.2 to 11 J cm{sup −2} is employed as pump beam to ablate Ge targets. In order to evaluate in-situe ablation threshold fluence of Ge by photoacoustic deflection technique, Continuous Wave (CW) He–Ne laser (632 nm, power 10 mW) is employed as a probe beam. It travels parallel to the target surface at a distance of 3 mm and after passing through Ge plasma it causes deflection due to density gradient of acoustic waves. The deflected signal is detected by photodiode and is recorded by oscilloscope. The threshold fluence of Ge, the velocity of ablated species and the amplitude of the deflected signal are evaluated. The threshold fluence of Ge comes out to be 0.5 J cm{sup −2} and is comparable with the analytical value. In order to compare the estimated value of threshold with ex-situe measurements, the quantitative analysis of laser irradiated Ge is performed by using SEM analysis. For this purpose Ge is exposed to single and multiple shots of 5, 10, 50 and 100 at various laser fluences ranging from 0.2 to 11 J cm{sup −2}. The threshold fluence for single and multiple shots as well as incubation coefficients are evaluated. It is observed that the value of incubation co-efficient decreases with increasing number of pulses and is therefore responsible for lowering the threshold fluence of Ge. SEM analysis also reveals the growth of various features such as porous structures, non-uniform ripples and blisters on the laser irradiated Ge. It is observed that both the fluence as well as number of laser shots plays a significant role for the growth of these structures.

  15. Nonlinear Coupled Dynamics of a Rod Fastening Rotor under Rub-Impact and Initial Permanent Deflection

    Directory of Open Access Journals (Sweden)

    Liang Hu

    2016-10-01

    Full Text Available A nonlinear coupled dynamic model of a rod fastening rotor under rub-impact and initial permanent deflection was developed in this paper. The governing motion equation was derived by the D’Alembert principle considering the contact characteristic between disks, nonlinear oil-film force, rub-impact force, unbalance mass, etc. The contact effects between disks was modeled as a flexural spring with cubical nonlinear stiffness. The coupled nonlinear dynamic phenomena of the rub-impact rod fastening rotor bearing system with initial permanent deflection were investigated by the fourth-order Runge-Kutta method. Bifurcation diagram, vibration waveform, frequency spectrum, shaft orbit and Poincaré map are used to illustrate the rich diversity of the system response with complicated dynamics. The studies indicate that the coupled dynamic responses of the rod fastening rotor bearing system under rub-impact and initial permanent deflection exhibit a rich nonlinear dynamic diversity, synchronous periodic-1 motion, multiple periodic motion, quasi-periodic motion and chaotic motion can be observed under certain conditions. Larger radial stiffness of the stator will simplify the system motion and make the oil whirl weaker or even disappear at a certain rotating speed. With the increase of initial permanent deflection length, the instability speed of the system gradually rises, and the chaotic motion region gets smaller and smaller. The corresponding results can provide guidance for the fault diagnosis of a rub-impact rod fastening rotor with initial permanent deflection and contribute to the further understanding of the nonlinear dynamic characteristics of the rod fastening rotor bearing system.

  16. Load-deflection characteristics of superelastic and thermal nickel-titanium wires.

    Science.gov (United States)

    Gatto, Elda; Matarese, Giovanni; Di Bella, Guido; Nucera, Riccardo; Borsellino, Chiara; Cordasco, Giancarlo

    2013-02-01

    The aim of this study was to investigate the mechanical properties of superelastic and thermal nickel-titanium (NiTi) archwires for correct selection of orthodontic wires. Seven different NiTi wires of two different sizes (0.014 and 0.016 inches), commonly used during the alignment phase, were tested. A three-point bending test was carried out to evaluate the load-deflection characteristics. The archwires were subjected to bending at a constant temperature of 37°C and deflections of 2 and 4 mm. Analysis of variance showed that thermal NiTi wires exerted significantly lower working forces than superelastic wires of the same size in all experimental tests (P Wire size had a significant effect on the forces produced: with an increase in archwire dimension, the released strength increased for both thermal and superelastic wires. Superelastic wires showed, at a deflection of 2 mm, narrow and steep hysteresis curves in comparison with the corresponding thermal wires, which presented a wide interval between loading and unloading forces. During unloading at 4 mm of deflection, all wires showed curves with a wider plateau when compared with 2 mm deflection. Such a difference for the superelastic wires was caused by the martensite stress induced at higher deformation levels. A comprehensive understanding of mechanical characteristics of orthodontic wires is essential and selection should be undertaken in accordance with the behaviour of the different wires. It is also necessary to take into account the biomechanics used. In low-friction mechanics, thermal NiTi wires are to be preferred to superelastic wires, during the alignment phase due to their lower working forces. In conventional straightwire mechanics, a low force archwire would be unable to overcome the resistance to sliding.

  17. A Kinematic Model for Vertical Axis Rotation within the Mina Deflection of the Walker Lane

    Science.gov (United States)

    Gledhill, T.; Pluhar, C. J.; Johnson, S. A.; Lindeman, J. R.; Petronis, M. S.

    2016-12-01

    The Mina Deflection, at the boundary between the Central and Southern Walker Lane, spans the California-Nevada border and includes a heavily-faulted Pliocene volcanic field overlying Miocene ignimbrites. The dextral Walker Lane accommodates 25% of relative Pacific-North America plate motion and steps right across the sinistral Mina deflection. Ours and previous work shows that the Mina Deflection partially accommodates deformation by vertical-axis rotation of up to 99.9o ± 6.1o rotation since 11 Ma. This rotation is evident in latite ignimbrite of Gilbert et al. (1971), which we have formalized as three members of Tuff of Huntoon Creek (THC). The welded, basal, normal-polarity Huntoon Valley Member of THC is overlain by the unwelded to partially-welded, reversed-polarity Adobe Hills Mbr. This member includes internal breaks suggesting multiple eruptive phases, but the paleomagnetic results from each are statistically indistinguishable, meaning that they were likely erupted in rapid succession (within a few centuries of one another). THC ends with a welded member exhibiting very shallow inclination and south declination that we call Excursional Mbr. One of the upper members has been dated at 11.17 ± 0.04 Ma. These Miocene units are overlain by Pliocene basalts, Quaternary alluvium, and lacustrine deposits. Our paleomagnetic results show a gradient between the zero rotation domain and high rotation across a 20km baseline. A micropolar model, based on 25 years of earthquake data from the Northern and Southern California Seismic Network, suggest the Mina Deflection is currently experiencing transpressional seismogenic deformation (Unruh et al., 2003). Accepting Unruh's model and assuming continuous rotation since 11 Ma, we propose a kinematic model for the western Mina Deflection that accommodates 90o of vertical axis rotation from N-S to ENE-WSW oriented blocks.

  18. Experimental Study of Hypersonic Inflatable Aerodynamic Decelerator (HIAD) Aeroshell with Axisymmetric Surface Deflection Patterns

    Science.gov (United States)

    Hollis, Brian R.; Hollingsworth, Kevin E.

    2017-01-01

    A wind tunnel test program was conducted to obtain aeroheating environment data on Hypersonic Inflatable Aerodynamic Decelerator aeroshells with flexible thermal protection systems. Data were obtained on a set of rigid wind tunnel models with surface deflection patterns of various heights that simulated a range of potential in-flight aeroshell deformations. Wind tunnel testing was conducted at Mach 6 at unit Reynolds numbers from 2.1 × 10(exp 6)/ft to 8.3 × 10(exp 6)/ft and angles of attack from 0 deg to 18 deg. Boundary-layer transition onset and global surface heating distribution measurements were performed using phosphor thermography and flow field images were obtained through schlieren photography. Surface deflections were found to both promote early transition of the boundary layer and to augment heating levels for both laminar and turbulent flows. A complimentary computational flow field study was also performed to provide heating predictions for comparison with the measurements as well as boundary layer flow field properties for use in correlating the data. Correlations of the wind tunnel data were developed to predict deflection effects on boundary layer transition and surface heating and were applied to both the wind tunnel test conditions and to the trajectory of NASA's successful IRVE-3 flight test. In general, the correlations produced at least qualitative agreement with the wind tunnel data, although the heating levels were underpredicted for some of the larger surface deflections. For the flight conditions, the correlations suggested that peak heating levels on the leeward side conical flank of the IRVE-3 vehicle may have exceeded those at nose for times late in the trajectory after the peak heating time point. However, the flight estimates were based on a conservative assumption of surface deflection magnitude (i.e., larger) than likely was produced in flight.

  19. Nanosecond pulsed laser ablation of Ge investigated by employing photoacoustic deflection technique and SEM analysis

    Science.gov (United States)

    Yaseen, Nazish; Bashir, Shazia; Shabbir, Muhammad Kaif; Jalil, Sohail Abdul; Akram, Mahreen; Hayat, Asma; Mahmood, Khaliq; Haq, Faizan-ul; Ahmad, Riaz; Hussain, Tousif

    2016-06-01

    Nanosecond pulsed laser ablation phenomena of single crystal Ge (100) has been investigated by employing photoacoustic deflection as well as SEM analysis techniques. Nd: YAG laser (1064 nm, 10 ns, 1-10 Hz) at various laser fluences ranging from 0.2 to 11 J cm-2 is employed as pump beam to ablate Ge targets. In order to evaluate in-situe ablation threshold fluence of Ge by photoacoustic deflection technique, Continuous Wave (CW) He-Ne laser (632 nm, power 10 mW) is employed as a probe beam. It travels parallel to the target surface at a distance of 3 mm and after passing through Ge plasma it causes deflection due to density gradient of acoustic waves. The deflected signal is detected by photodiode and is recorded by oscilloscope. The threshold fluence of Ge, the velocity of ablated species and the amplitude of the deflected signal are evaluated. The threshold fluence of Ge comes out to be 0.5 J cm-2 and is comparable with the analytical value. In order to compare the estimated value of threshold with ex-situe measurements, the quantitative analysis of laser irradiated Ge is performed by using SEM analysis. For this purpose Ge is exposed to single and multiple shots of 5, 10, 50 and 100 at various laser fluences ranging from 0.2 to 11 J cm-2. The threshold fluence for single and multiple shots as well as incubation coefficients are evaluated. It is observed that the value of incubation co-efficient decreases with increasing number of pulses and is therefore responsible for lowering the threshold fluence of Ge. SEM analysis also reveals the growth of various features such as porous structures, non-uniform ripples and blisters on the laser irradiated Ge. It is observed that both the fluence as well as number of laser shots plays a significant role for the growth of these structures.

  20. The Deflector Selector: A Machine Learning Framework for Prioritizing Deflection Technology Development

    Science.gov (United States)

    Van Heerden, Elmarie; Erasmus, Nicolas; Greenberg, Adam; Nesvold, Erika; Galache, Jose Luis; Dahlstrom, Eric; Marchis, Franck

    2016-10-01

    On 15 February, 2013, a ~15 m diameter asteroid entered the Earth's atmosphere over Russia. The resulting shockwave injured nearly 1500 people, and incurred ~33 million (USD) in infrastructure damages. The Chelyabinsk meteor served as a forceful demonstration of the threat posed to Earth by the hundreds of potentially hazardous objects (PHOs) that pass near the Earth every year. Although no objects have yet been discovered on an impact course for Earth, an impact is virtually statistically guaranteed at some point in the future. While many impactor deflection technologies have been proposed, humanity has yet to demonstrate the ability to divert an impactor when one is found. Developing and testing any single proposed technology will require significant research time and funding. This leaves open an obvious question - towards which technologies should funding and research be directed, in order to maximize our preparedness for when an impactor is eventually found?To help answer this question, we have created a detailed framework for analyzing various deflection technologies and their effectiveness. Using an n-body integrator (REBOUND), we have simulated the attempted deflections of a population of Earth-impacting objects with a variety of velocity perturbations (∂Vs), and measured the effects that these perturbations had on impact probability. We then mapped the ∂Vs applied in the orbital simulations to the technologies capable of achieving those perturbations, and analyzed which set of technologies would be most effective at preventing a PHO from impacting the earth. As a final step, we used the results of these simulations to train a machine learning algorithm. This algorithm, combined with a simulated PHO population, can predict which technologies are most likely to be needed. The algorithm can also reveal which impactor observables (mass, spin, orbit, etc.) have the greatest effect on the choice of deflection technology. These results can be used as a tool to

  1. The adhesive potential of dentin bonding systems assessed using cuspal deflection measurements and cervical microleakage scores.

    Science.gov (United States)

    Sultan, Ahmed; Moorthy, Advan; Fleming, Garry J P

    2014-10-01

    To assess the cuspal deflection and cervical microleakage of standardized mesio-occluso-distal (MOD) cavities restored with a dimethacrylate resin-based-composite (RBC) placed with one 3-step, one 2-step and three 1-step bonding systems and compared with the unbound condition. Forty-eight sound maxillary premolar teeth with standardized MOD cavities were randomly allocated to six groups. Restoration was performed in eight oblique increments using a quartz-tungsten-halogen (QTH) light curing unit (LCU) with the bonding condition as the dependent variable. Buccal and palatal cuspal deflections were recorded post-irradiation using a twin channel deflection measuring gauge at 0, 30, 60 and 180s. Following restoration, the teeth were thermocycled, immersed in a 0.2% basic fuchsin dye for 24h, sectioned and examined for cervical microleakage assessment. The mean total cuspal deflection measurements with the one 3-step, one 2-step and three 1-step bonding systems were 11.26 (2.56), 10.95 (2.16), 10.03 (2.05) (Futurabond(®) DC SingleDose), 6.37 (1.37) (Adper™ Prompt™ L-Pop™), 8.98 (1.34) μm (All-Bond SE(®)), respectively when compared with the unbound condition (6.46 (1.88) μm) The one-way ANOVA of the total cuspal deflection measurements identified statistical differences (pbonding system although differences between the bonding systems were evident (pbonding technologies available to practitioners for RBCs. Poorly performing adhesives can be identified which indicated the technique may be useful as a screening tool for assessing existing and new bonding technologies which offers the potential to limit complications routinely encountered with Class II RBC restorations. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  2. Electrostatic deflection of a molecular beam of massive neutral particles: Fully field-oriented polar molecules within superfluid nanodroplets

    CERN Document Server

    Merthe, Daniel J

    2016-01-01

    Electric deflection measurements on liquid helium nanodroplets doped with individual polar molecules demonstrate that the cold superfluid matrix enables full orientation of the molecular dipole along the external field. This translates into a deflection force which is increased enormously by comparison with typical deflection experiments, and it becomes possible to measurably deflect neutral doped droplets with masses of tens to hundreds of thousands of Daltons. This approach permits preparation and study of continuous fluxes of fully oriented polar molecules and is broadly and generally applicable, including to complex and biological molecules. It is shown that the dipole moments of internally cryogenically cold molecules can be directly determined from a deflection measurement on the doped nanodroplet beam.

  3. Orbital deflection of fragments produced through peripheral reactions of heavy nuclei at 290 MeV/nucleon

    Science.gov (United States)

    Momota, S.; Kanazawa, M.; Kitagawa, A.; Sato, S.

    2017-02-01

    The orbital deflection phenomenon of reaction products formed through peripheral reactions of heavy nuclei at intermediate energy is studied to examine the contributions of the Coulomb potential and nuclear potential that act between the projectile and target nuclei. The angular distributions of fragments produced in 1-nucleon removal and exchange reactions of 40Ar and 84Kr beams with C, Al, Nb, Tb, and Au targets at 290 MeV/nucleon were observed. A significant deflection effect was successfully identified in observed angular distributions at energies as low as Ei = 100 MeV/nucleon. The deflection effect increases with the atomic number of the target nuclei. The observed deflection effect is consistently explainable using the classical deflection angle, which is obtained with respect to a simple framework of the Coulomb potential and the real part of the energy-dependent nuclear potential, and the characteristic impact parameter between the projectile and target nuclei.

  4. Effect of deflecting ring on noise generated by outdoor set of a split-unit air conditioner

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Junwei; Ding, Guoliang [Institute of Refrigeration and Cryogenics, Shanghai JiaoTong University, Shanghai 200030 (China)

    2006-05-15

    In order to analyze the influence of the deflecting ring on the noise generated by the outdoor set of a split-unit air conditioner, the flow field in the outdoor set is simulated with the CFD software STAR-CD, the relative turbulent intensities are computed and the influence of the width and contoured duct of the deflecting ring on the noise generated by the outdoor set is analyzed. The results of computation and experiment show that there is an optimal width of the deflecting ring, corresponding to the minimum noise generated by the outdoor set. In addition, the influence of the contoured duct of the deflecting ring on the noise generated by the outdoor set is analyzed and a double contoured duct is designed. The results of computation and experiment verify that the deflecting ring with double contoured duct can improve the aerodynamic performance and reduce the noise generated by the outdoor set. (author)

  5. Transverse C-band deflecting structure for longitudinal electron-bunch-diagnosis in XFEL “SACLA”

    Energy Technology Data Exchange (ETDEWEB)

    Ego, H., E-mail: ego@spring8.or.jp [Japan Synchrotron Radiation Research Institute (JASRI), Kouto, Sayo, Hyogo (Japan); Maesaka, H.; Sakurai, T.; Otake, Y. [RIKEN SPring-8 Center, Kouto, Sayo, Hyogo (Japan); Hashirano, T.; Miura, S. [Mitsubishi Heavy Industries, Ltd. (MHI), Itozaki, Mihara, Hiroshima (Japan)

    2015-09-21

    In the 8 GeV compact X-ray FEL “SACLA,” a single bunch of electrons is compressed to a duration of approximately 30 fs to yield a peak current of 3 kA, which creates brilliant self-amplified spontaneous emission. To measure the longitudinal profile of an ultrashort electron bunch and verify the compression, we developed a high-gradient C-band RF deflecting structure 1.8 m long and periodically loaded with racetrack-shaped irises. The irises generated a high deflection gradient for the vertically deflecting HEM11-5π/6 dipole mode and suppressed rotation of the deflection plane. The two structures were fabricated and generated a stable total deflecting voltage exceeding 60 MV and revealed the longitudinal electron-bunch profile with an effective time resolution of approximately 10 fs.

  6. Viscoelastic Modelling of Road Deflections for use with the Traffic Speed Deflectometer

    DEFF Research Database (Denmark)

    Pedersen, Louis

    This Ph.D. study is at its core about how asphalt and road structures responds to dynamic loads. Existing models for the deflections under a moving load using beam equations are revisited and it is concluded they leave room for improvement for the particular setup and problem at hand. Then a diff......This Ph.D. study is at its core about how asphalt and road structures responds to dynamic loads. Existing models for the deflections under a moving load using beam equations are revisited and it is concluded they leave room for improvement for the particular setup and problem at hand...... of a generalized Maxwell model. Validations by comparison to ViscoRoute simulations are also made. This justifies the use of the Laplace FEM for generating simulated data using a Huet-Sayegh model for the visco-elastic behaviour of asphalt. These simulated data, along with measured data, are then used to suggest...

  7. Principle and Feasibility of Electric or Magnetic Field Deflection-Projection Based Rapid Prototyping Technique

    Institute of Scientific and Technical Information of China (English)

    张连洪; 李双义; 张宝峰; 熊晓明

    2003-01-01

    Rapid prototype manufacturing(RPM) is a new advanced manufacturing technology, which is based on the philosophy of materials increasing of lay by lay forming. Zero adventure rapid design/manufacturing can be realized with rapid prototypes of 3D CAD of products. Rapid prototyping has been an effective tool of R&D of new products. A novel rapid prototyping and manufacturing (RP&M) technique is brought forward. The principle of the process is to form layered sections and to make the prototype or part layer-by-layer by deflection-projection of electric charged powder granules passing through electric or magnetic field and by controllable line and field scan of the powder granule beam. The feasibility issue of the process is theoretically and experimentally investigated.It shows that deflection-projection of electric charged powder granules beam passing through electric field can be significant and feasible to the rapid prototyping technique.

  8. Evaluating Loading Deflection of Distraction Osteogenic Rib in a Rabbit Model.

    Science.gov (United States)

    Shen, Weimin; Tang, Chenlu; Yang, Junyi; Kong, Liangliang; Zhang, Xiaoying

    2016-10-01

    The treatment of patients with partially atrophic rib and rib defects requires an ideal arc of the rib that has adequate bone length and width. To design and assemble a distraction device with a strain gauge, we need to establish an animal model for testing it during rib distraction osteogenesis. Osteotomies were performed at the same position in the fifth rib in 8 rabbits. Customized distraction devices attached to strain gauges were used to distract the ribs. After a month of distraction and consolidation, loading deflection gauges were used, and specimens were examined histologically to record bone formation. Distraction osteogenesis was carried out successfully in all rabbits when the device used to distract the rib up to 4 cm. The device can be used for strain testing during rib distraction osteogenesis performed in a rabbit model. There was no significant difference in the loading deflection gauges of the bone between osteogenic and contralateral ribs. This animal model of costal distraction osteogenesis is successful.

  9. The impact of galaxy cluster environment on the deflection properties of extragalactic gravitational lenses

    CERN Document Server

    Poplavsky, Alexander L

    2014-01-01

    In this paper the influence of a galaxy cluster halo on the deflection properties of its galaxies is investigated. For this purpose triaxial cluster halo models are developed based on the Einasto and Navarro-Frenk-White density profiles. Applying Monte-Carlo technique external shear and convergence are modelled for random positions of a test galaxy within the cluster. In the simulations the following parameters of the cluster and galaxies are varied: density profile, its slope, mass, characteristic and outer radii. Also, galaxies in the close vicinity are treated separately, whereas distant objects are contributed to the smooth mass distribution. As a result of the multiple simulations robust estimations of external shear and convergence as well as their constraints relatively to variable cluster parameters and observer location effects are derived. It is demonstrated that the external deflection by the cluster mass strongly depends on the applied density profile.

  10. Deflected Pathways: Becoming Aggressive, Socially Withdrawn, or Prosocial with Peers During the Transition to Adolescence

    Science.gov (United States)

    Monahan, Kathryn C.; Booth-LaForce, Cathryn

    2014-01-01

    Although research has suggested strong continuity in children's adaptive or maladaptive behavior with peers across the transition to adolescence, less is known about deflected developmental pathways of peer social competence across this transition. This study investigates how mother-child and best friend relationship quality predict the deflection of youth from adaptive to maladaptive behavior with peers or the reverse. Using data from the NICHD Study of Early Child Care and Youth Development (N=1055), high-quality friendships were associated with changes in peer social competence from 3rd to 6th grade. More positive and fewer negative interactions with a friend were linked with becoming more prosocial with peers, whereas less positive interactions with a friend were linked to becoming aggressive or withdrawn. PMID:27231420

  11. Improvement on straightness of metal bar based on straightening stroke-deflection model

    Institute of Scientific and Technical Information of China (English)

    LEOPOLD; Juergen

    2009-01-01

    The straightening technics is one of important means to improve the straightness of metal bar. A nove way of predicting the straightening stroke is proposed based on mathematical methods and bending experimental and numerical simulation. The experimental and numerical simulation is conducted by following the mathematical load-stroke model of press straightening process under the elastic-plastic theory. For the linear guide rails, as an example, the stroke-deflection model focusing on the straight-ening stroke prediction can be achieved by contrasting and integrating the bending experimental results and finite element methods (FEM) simulation data. And then the formula for predicting the straightening stroke is presented based on the precise straightening stroke-deflection model. The stroke prediction formula with high precision can be applied to the straightening stroke prediction in the high straightness metal bar manufacturing process and automatic straightening machine conveniently.

  12. Improvement on straightness of metal bar based on straightening stroke-deflection model

    Institute of Scientific and Technical Information of China (English)

    LU Hong; LING He; LEOPOLD Juergen; ZHANG Xiao; GUO ChangQiao

    2009-01-01

    The straightening technics is one of important means to improve the straightness of metal bar. A novel way of predicting the straightening stroke is proposed based on mathematical methods and bending experimental and numerical simulation. The experimental and numerical simulation is conducted by following the mathematical load-stroke model of press straightening process under the elastic-plastic theory. For the linear guide rails, as an example, the stroke-deflection model focusing on the straightening stroke prediction can be achieved by contrasting and integrating the bending experimental results and finite element methods (FEM) simulation data. And then the formula for predicting the straightening stroke is presented based on the precise straightening stroke-deflection model. The stroke prediction formula with high precision can be applied to the straightening stroke prediction in the high straightness metal bar manufacturing process and automatic straightening machine conveniently.

  13. Deflection tomography of a complex flow field based on the visualization of projection array

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Bin; Miao Zhanli, E-mail: zb-sh@163.com [College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao, Shandong 266061 (China)

    2011-02-01

    Tomographic techniques are used for the investigation of complex flow fields by means of deflectometric methods. A new deflection tomographic setup for obtaining an array of multidirectional deflectograms is presented. Deflection projections in different angles of view can be captured synchronously in same optical path condition and arranged on the camera in two rows with three views in each row. Tikhonov regularization method is used to reconstruct temperature distribution from deflectometric projection data. The conjugate gradient method is used to compute the regularized solution for the least-square equations. The asymmetric flame temperature distribution in the horizontal section was reconstructed from limited view angle projections. The experimental results of reconstruction from real projection data were satisfactory when compared with the direct thermocouple measurements.

  14. Fiber optic system for deflection and damage detection in morphing wing structures

    Science.gov (United States)

    Scheerer, M.; Djinovic, Z.; Schüller, M.

    2013-04-01

    Within the EC Clean Sky - Smart Fixed Wing Aircraft initiative concepts for actuating morphing wing structures are under development. In order for developing a complete integrated system including the actuation, the structure to be actuated and the closed loop control unit a hybrid deflection and damage monitoring system is required. The aim of the project "FOS3D" is to develop and validate a fiber optic sensing system based on low-coherence interferometry for simultaneous deflection and damage monitoring. The proposed system uses several distributed and multiplexed fiber optic Michelson interferometers to monitor the strain distribution over the actuated part. In addition the same sensor principle will be used to acquire and locate the acoustic emission signals originated from the onset and growth of defects like impact damages, cracks and delamination's. Within this paper the authors present the concept, analyses and first experimental results of the mentioned system.

  15. Post-post-Newtonian deflection of light ray in multiple systems with PPN parameters

    Institute of Scientific and Technical Information of China (English)

    Gong Yan-Xiang; Wu Xiao-Mei

    2011-01-01

    The post-Newtonian scheme in multiple systems with post-Newtonian parameters presented by Klioner and Soffel is extended to the post-post-Newtonian (PPN) order for light propagation problem in the solar system. Under considering the solar system experiment requirement, a new parameter e is introduced. This extension does not change the virtue of the scheme on the linear partial differential equations of the potential and vector potential mentioned in previous work. Furthermore, this extension is based on the former work done by Richter and Matzner in one global system theory. As an application, we also consider the deflection of light ray in the global coordinates. And the deflection angle of light ray is obtained with post-Newtonian parameters.

  16. Wrinkling of extensional thin films through modified large deflection equations analytically and experimentally

    Directory of Open Access Journals (Sweden)

    M.-H. R. Jen

    2015-12-01

    Full Text Available The stretch-induced wrinkling of thin films is solved through the modified von Kármán large deflection equations by first selecting the suitable deformation expressions that satisfy boundary conditions. Then, adopting the principle of minimum potential energy we obtain the deformations of simply supported rectangular thin films. The obtained significant deflections are nonlinearly elastic and of the lowest order of infinite solutions. The parameters of aspect ratio, the thickness and material of thin films are studied analytically and numerically. The highlighted results of wrinkle amplitude and load are in good agreement with experiments. The methodology also indicates the limit load impending plasticity and predicts the applied load precisely for each wrinkle. Further, it can be extended to the variety of multifunctional orthotropic and multi-layered thin films.

  17. Study on precision processing of L-form ZnSe deflect prism

    Science.gov (United States)

    Ye, Sizhe; Hui, Changshun; Zhang, Hao; Lu, Yongbin

    2016-10-01

    As the core component of optical system of Roll-Pitch seekers, the L-form ZnSe deflect prism is directly affecting the imaging quality of optical. For L-form defect prism's complex polyhedron plane structure and the feature of CVD ZnSe polycrystalline material, this paper propose one processing of single point diamond fly-cutting, analyze the transformation calculation method of each plane's coordinate. A kind of special clamp which ensure that all working surface of prism could be cut by once clamping is designed. Base on parameters of turning for CVD ZnSe , the deflect prisms are been processed, the measure result of angle error is below 12", the surface error (rms) reach 0.022λ, which satisfies the demand of manufacturing accuracy. It provide effective processing methods for optical parts with complex space.

  18. Analytical Approach to Predict Pre–Camber Deflection of the Pre-stressed Glulam Beams

    Directory of Open Access Journals (Sweden)

    Anshari B.

    2015-01-01

    Full Text Available A new approach to reinforce glulam timber beams using compressed wood (CW has been developed by the Author. The compressed wood blocks are inserted into pre-cut holes on the top of glulam beams to produce pre-camber and to generate initial tensile and compressive stresses on the top and on the bottom extreme fiber of the glulam beam, respectively. A simple analytical approach has been developed to predict pre-camber deflections of the beams reinforced with three CW blocks. Assuming that moisture-dependent expansion of the CW block creates an interactive linear pressure between the glulam beam and the CW block, this would generate a pair of eccentric force away from the neutral axis of the beam. It is shown that the pre-camber deflection predicted at midspan of the short beams with various reinforcing arrangements give good agreement with the measured pre-camber from previous experimental results.

  19. Direct measurement of the beam deflection angle using the axial B-dot field

    Directory of Open Access Journals (Sweden)

    Xiaozhong He

    2011-05-01

    Full Text Available Beam position monitors are an important diagnostics tool for particle accelerator operation and related beam dynamics research. The measurement of the beam deflection angle, or moving direction of a charged particle beam with respect to the beam pipe axis, can provide useful additional information. Beam monitors sensitive to the beam’s azimuthal B-dot field (sometimes referred as B dots are used to measure the displacement (position of the beam centroid, as the beam generates a dipole term of the azimuthal magnetic field. Similarly, a dipole term of the axial magnetic field will be generated by the beam moving in a direction not parallel to the axis of the beam pipe. In this paper, a new method using the axial B-dot field is presented to measure the beam deflection angle directly, including the theoretical background. Simulations using the MAFIA numerical code have been performed, demonstrating a good agreement to the new established analytical model.

  20. Development and testing of a fracture energy-based model of explosive asteroid deflection

    Science.gov (United States)

    Veerkamp, James A.

    While asteroid deflection has been studied for the past half century, efforts have generally been directed towards methods that attempt to minimize disruption of the rock body. In order to widen the base of research, a fracture energy-based model of asteroid fragmentation was developed and applied to both asteroid scale and lab testable scale cases. Modeling of the orbital case suggests the capability to deflect a 100 meter diameter asteroid on a 10 year timescale. The model's predicted energy transfer is then compared to laboratory testing using a ballistic pendulum. The results of this testing suggest that the model as described overestimates the efficiency of energy transfer into momentum. However, further approaches are suggested that might improve model accuracy as well as energy transfer efficiency.

  1. Characterization of acoustic effects on flame structures by beam deflection technique

    Energy Technology Data Exchange (ETDEWEB)

    Bedat, B.; Kostiuk, L.W.; Cheng, R.K.

    1993-10-01

    This work shows that the acoustic effects are the causes of the small amplitude flame wrinkling and movements seen in all the different gravitational conditions. The comparison between the acoustic velocity and beam deflection spectra for the two conditions studied (glass beads and fiber glass) demonstrates clearly this flame/acoustic coupling. This acoustic study shows that the burner behaves like a Helmholtz resonator. The estimated resonance frequency corresponds well to the experimental measurements. The fiber glass damps the level of the resonance frequency and the flame motion. The changes shown in normalized beam deflection spectra give further support of this damping. This work demonstrates that the acoustics has a direct influence on flame structure in the laminar case and the preliminary results in turbulent case also show a strong coupling. The nature of this flame/acoustic coupling are still not well understood. Further investigation should include determining the frequency limits and the sensitivity of the flame to acoustic perturbations.

  2. Deflecting Easy-axis of Fe304 Single Crystal Nanowires by Magnetic-field-induced Method

    Institute of Scientific and Technical Information of China (English)

    W. Wang; S. Y. Wang

    2012-01-01

    In order to control the orientation of easy-axis of magnetic nanowires, FesO4 single crystal nanowires with easy-axis perpendicular to wire-axis were prepared successfully by means of a magnetic-field-induced method. Analysis of X-ray diffraction and electron diffraction pattern showed that there was a wide-angle deflection of easy-axis in the prepared Fe304 nanowires. A high saturation magnetization (82 emu/g) of the FesO4 nanowires was achieved at room temperature. The benefits and mechanism of the deflection of easy-axis from its wire-axis in FesO4 single crystal nanowires were discussed. The results are expected to broaden the magnetic properties of traditional ferrite nanowires.

  3. Nanoscale deflection detection of a cantilever-based biosensor using MOSFET structure: A theoretical analysis

    Science.gov (United States)

    Paryavi, Mohsen; Montazeri, Abbas; Tekieh, Tahereh; Sasanpour, Pezhman

    2016-10-01

    A novel method for detection of biological species based on measurement of cantilever deflection has been proposed and numerically evaluated. Employing the cantilever as a moving gate of a MOSFET structure, its deflection can be analyzed via current characterization of the MOSFET consequently. Locating the cantilever as a suspended gate of a MOSFET on a substrate, the distance between cantilever and oxide layer will change the carrier concentration. Accordingly, it will be resulted in different current voltage characteristics of the device which can be easily measured using simple apparatuses. In order to verify the proposed method, the performance of system has been theoretically analyzed using COMSOL platform. The simulation results have confirmed the performance and sensitivity of the proposed method.

  4. Roll and Bank Estimation Using GPS/INS and Suspension Deflections

    Directory of Open Access Journals (Sweden)

    Lowell S. Brown

    2015-01-01

    Full Text Available This article presents a method that provides an estimate of road bank by decoupling the vehicle roll due to the dynamics and the roll due to the road bank. Suspension deflection measurements were used to provide a measurement of the relative roll between the vehicle body frame and the axle frame or between the sprung mass and the unsprung mass, respectively. A deflection scaling parameter was found via suspension geometry and dynamic analysis. The relative roll measurement was then incorporated into two different kinematic navigation models based on extended Kalman filter (EKF architectures. Each algorithm was tested and then verified on the Prowler ATV experimental platform at the National Center for Asphalt Technology (NCAT. Experimental data showed that both the cascaded and coupled approach performed well in providing estimates of the current vehicle roll and instantaneous road bank.

  5. Design and studies on the traveling wave transverse RF deflecting structure

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jing-Ru; HOU Mi; DAI Jian-Ping; PEI Shi-Lun; PEI Guo-Xi

    2008-01-01

    With the development of free electron laser (FEL) and the international linear collider (ILC), the electron bunch length is getting smaller and smaller. The traveling-wave transverse RF deflecting structure is an important part of the RF deflecting method for bunch length measurement and phase space diagnostics.The operation mode in RF deflector is the "TM11-like" mode. Since the TM11-like mode in this structure has a pair of degenerate dipole modes, two additional holes are provided on either side of each iris to stabilize the mode. The simulation and optimization have been done. A prototype has been fabricated and tested. The cold test results have been compared with the simulations of the first three modes.

  6. Deflection of Light and Shapiro Delay: An Equivalent Medium Theory Approach

    CERN Document Server

    Khorasani, Sina Ataollah

    2012-01-01

    We discuss the deflection of light and Shapiro delay under the influence of gravity as described by Schwarzschild metric. We obtain an exact expression based on the coordinate velocity, as first set forth by Einstein, and present a discussion on the effect of velocity anisotropy. We conclude that the anisotropy in the coordinate velocity, as the velocity apparent to a distant observer, gives rise to a third order error in the deflection angle, so that the practical astronomical observations from gravitational lensing data remain inconclusive on the anisotropy. However, measurement of Shapiro delay provides a fairly convenient way to determine whether the spacetime is optically anisotropic for a distant observer or not. We calculate the Shapiro delay for a round trip path between Earth and Venus and observe excellent agreement to two experimentally reported values measured during a time span of six months in 1967, without any need to extra fitting parameters. This is while the expected delay obtained from an i...

  7. Multi-beamlet investigation of the deflection compensation methods of SPIDER beamlets

    Energy Technology Data Exchange (ETDEWEB)

    Baltador, C., E-mail: carlo.baltador@igi.cnr.it; Veltri, P.; Agostinetti, P.; Chitarin, G.; Serianni, G. [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete S.p.A), Corso Stati Uniti, 4, 35127 Padova (Italy)

    2016-02-15

    SPIDER (Source for Production of Ions of Deuterium Extracted from a Rf plasma) is an ion source test bed designed to extract and accelerate a negative ion current up to 40 A and 100 kV whose first beam is expected by the end of 2016. Two main effects perturb beamlet optics during the acceleration stage: space charge repulsion and the deflection induced by the permanent magnets (called co-extracted electron suppression magnets) embedded in the EG. The purpose of this work is to evaluate and compare benefits, collateral effects, and limitations of electrical and magnetic compensation methods for beamlet deflection. The study of these methods has been carried out by means of numerical modeling tools: multi-beamlet simulations have been performed for the first time.

  8. Electronic spectroscopies

    NARCIS (Netherlands)

    Weckhuysen, B.M.; Schoonheydt, R.A.

    2000-01-01

    Diffuse reflectance spectroscopy (DRS) in the ultraviolet, visible and near-infrared region is a versatile spectroscopic technique, as both d-d and charge transfer transitions of supported TMI can be probed. One of the advantages of electronic spectroscopy is that the obtained information is

  9. Deflection Determination of Reinforced Concrete Support Poles for Overhead Transmission Lines

    Directory of Open Access Journals (Sweden)

    M. A. Korotkevich

    2011-01-01

    Full Text Available The paper contains values of torque magnification ratio while shifting vertical loads due to horizontal wind forces affecting on supports of overhead transmission lines of 35 kV and higher. These values pertain to various types of unified reinforced concrete conic and cylindrical supports while changing climatic conditions. The values make it possible to exclude rather complicated calculations in respect of support deflection in the case when there is uncertainty in initial data.

  10. Route Height Connection Across the Sea by Using the Vertical Deflections and Ellipsoidal Height Data

    Institute of Scientific and Technical Information of China (English)

    GUO Jin-yun; CHEN Yong-ning; LIU Xin; ZHONG Shi-xia; MAI Zhao-qiu

    2013-01-01

    Distance between the main land and island is so long that it is very difficult to precisely connect the height datum across the sea with the traditional method like the trigonometric leveling,or it is very expensive and takes long time to implement the height transfer with the geopotential technique.We combine the data of GPS surveying,astro-geodesy and EGM2008 to precisely connect the orthometric height across the sea with the improved astronomical leveling method in the paper.The Qiongzhou Strait is selected as the test area for the height connection over the sea.We precisely determine the geodetic latitudes,longitudes,heights and deflections of the vertical for four points on both sides across the strait.Modeled deflections of the vertical along the height connecting routes over the sea are determined with EGM2008 model based on the geodetic positions and heights of the sea segmentation points from DNSC08MSS model.Differences of the measured and modeled deflections of the vertical are calculated at four points on both sides and linearly change along the route.So the deflections of the vertical along the route over the sea can be improved by the linear interpolation model.The results are also in accord with those of trigonometirc levelings.The practical case shows that we can precisely connect the orthometric height across the Qiongzhou Strait to satisfy the requirement of order 3 leveling network of China.The method is very efficient to precisely connect the height datum across the sea along the route up to 80 km.

  11. Picoradian deflection measurement with an interferometric quasi-autocollimator using weak value amplification.

    Science.gov (United States)

    Turner, Matthew D; Hagedorn, Charles A; Schlamminger, Stephan; Gundlach, Jens H

    2011-04-15

    We present an "interferometric quasi-autocollimator" that employs weak value amplification to measure angular deflections of a target mirror. The device has been designed to be insensitive to all translations of the target. We present a conceptual explanation of the amplification effect used by the device. An implementation of the device demonstrates sensitivities better than 10 picoradians per root hertz between 10 and 200 Hz.

  12. Shape Tracking of a Dexterous Continuum Manipulator Utilizing Two Large Deflection Shape Sensors

    Science.gov (United States)

    Farvardin, Amirhossein; Grupp, Robert; Murphy, Ryan J.; Taylor, Russell H.; Iordachita, Iulian

    2016-01-01

    Dexterous continuum manipulators (DCMs) can largely increase the reachable region and steerability for minimally and less invasive surgery. Many such procedures require the DCM to be capable of producing large deflections. The real-time control of the DCM shape requires sensors that accurately detect and report large deflections. We propose a novel, large deflection, shape sensor to track the shape of a 35 mm DCM designed for a less invasive treatment of osteolysis. Two shape sensors, each with three fiber Bragg grating sensing nodes is embedded within the DCM, and the sensors’ distal ends fixed to the DCM. The DCM centerline is computed using the centerlines of each sensor curve. An experimental platform was built and different groups of experiments were carried out, including free bending and three cases of bending with obstacles. For each experiment, the DCM drive cable was pulled with a precise linear slide stage, the DCM centerline was calculated, and a 2D camera image was captured for verification. The reconstructed shape created with the shape sensors is compared with the ground truth generated by executing a 2D–3D registration between the camera image and 3D DCM model. Results show that the distal tip tracking accuracy is 0.40 ± 0.30 mm for the free bending and 0.61 ± 0.15 mm, 0.93 ± 0.05 mm and 0.23 ± 0.10 mm for three cases of bending with obstacles. The data suggest FBG arrays can accurately characterize the shape of large-deflection DCMs.

  13. Flow visualization and interpretation of visualization data for deflected thrust V/STOL nozzles

    Science.gov (United States)

    Kao, H. C.; Burstadt, P. L.; Johns, A. L.

    1984-01-01

    Flow visualization studies were made for four deflected thrust nozzle models at subsonic speeds. Based on topological rules and the assumption that observed streaks constitute continuous vector fields, available visualization pictures are interpreted and flow patterns on interior surfaces of the nozzles are synthesized. In particular, three dimensional flow structure and separations are discussed. From the synthesized patterns, the overall features of the flow field in a given nozzle can be approximately perceived. Previously announced in STAR as N84-14147

  14. Acousto-optic modulation and deflection of terahertz electromagnetic radiation in nonpolar liquids

    Science.gov (United States)

    Nikitin, P. A.; Voloshinov, V. B.; Gerasimov, V. V.; Knyazev, B. A.

    2017-07-01

    The results of a series of experiments on controlled deflection of electromagnetic radiation of a free-electron laser upon diffraction by an acoustic wave in nonpolar liquids are presented. Acoustic and optical properties of liquids that are transparent in the terahertz range are discussed. It is demonstrated that nonpolar liquids may turn out to be a more efficient acousto-optic interaction medium than dielectric crystals or semiconductors.

  15. All-optical optoacoustic microscopy system based on probe beam deflection technique

    Science.gov (United States)

    Maswadi, Saher M.; Tsyboulskic, Dmitri; Roth, Caleb C.; Glickman, Randolph D.; Beier, Hope T.; Oraevsky, Alexander A.; Ibey, Bennett L.

    2016-03-01

    It is difficult to achieve sub-micron resolution in backward mode OA microscopy using conventional piezoelectric detectors, because of wavefront distortions caused by components placed in the optical path, between the sample and the objective lens, that are required to separate the acoustic wave from the optical beam. As an alternate approach, an optoacoustic microscope (OAM) was constructed using the probe beam deflection technique (PBDT) to detect laserinduced acoustic signals. The all-optical OAM detects laser-generated pressure waves using a probe beam passing through a coupling medium, such as water, filling the space between the microscope objective lens and sample. The acoustic waves generated in the sample propagate through the coupling medium, causing transient changes in the refractive index that deflect the probe beam. These deflections are measured with a high-speed, balanced photodiode position detector. The deflection amplitude is directly proportional to the magnitude of the acoustic pressure wave, and provides the data required for image reconstruction. The sensitivity of the PBDT detector expressed as noise equivalent pressure was 12 Pa, comparable to that of existing high-performance ultrasound detectors. Because of the unimpeded working distance, a high numerical aperture objective lens, i.e. NA = 1, was employed in the OAM to achieve near diffraction-limited lateral resolution of 0.5 μm at 532nm. The all-optical OAM provides several benefits over current piezoelectric detector-based systems, such as increased lateral and axial resolution, higher sensitivity, robustness, and potentially more compatibility with multimodal instruments.

  16. Development of Experimental Device for Compression Load Deflection of Car Door Seals

    Institute of Scientific and Technical Information of China (English)

    赵建才; 朱训生; 万德安

    2003-01-01

    A new experimental device has been developed for analyzing compression load deflection of the door seal by using stereovision theory. Precision instruments of optical grating and force sensor are also integrated in this device. Force-displacement response characteristics of compression at varied speed can be controlled. Solid foundations for characteristic and structure as well as optimization design of the car door seal are elucidated.

  17. Applicability valuation for evaluation of surface deflection in automotive outer panels

    Directory of Open Access Journals (Sweden)

    D.H. Park

    2008-12-01

    Full Text Available Purpose: Upon unloading in a forming process there is elastic recovery, which is the release of the elasticstrains and the redistribution of the residual stresses through the thickness direction, thus producing surfacedeflection. It causes changes in shape and dimensions that can create major problem in the external appearanceof outer panels. Thus surface deflection prediction is an important issue in sheet metal forming industry. Manyfactors could affect surface deflection in the process, such as material variations in mechanical properties, sheetthickness, tool geometry, processing parameters and lubricant condition.Design/methodology/approach: Numerical simulation of process was performed by the use of finite elementmethod, paying attention particularly to the thickness distribution and surface deflection of the drawn outerpanel and the outline flange during forming. Simulation procedures of automotive outer panel as large size shapeare as follows; 1 Acquisition of drawing parts 2 Laser scanning for generating CAD model 3 CAD modelgeneration 4 Simulation model operation 5 Simulation execution and analyses of simulation results.Findings: The development of automation in stamping and assembly processes of automobile manufacture willrequire an excellent surface quality of formed panels and also their accurate dimensions.Practical implications: The use of high strength steel sheets in the manufacturing of automobile outer panels hasincreased in the automotive industry over the years because of its lightweight and fuel-efficient improvement.But one of the major concerns of stamping is surface deflection in the formed outer panels. Hence, to be costeffective, accurate prediction must be made of its formability. The automotive industry places rigid constraintson final shape and dimensional tolerances as well as external appearance quality of outer panels. The numericalsimulation makes it possible to design and optimize the total process to a level

  18. Deflection measurement system for the hybrid iii six-year-old biofidelic abdomen.

    Science.gov (United States)

    Gregory, T Stan; Howes, Meghan K; Rouhana, Stephen W; Hardy, Warren N

    2012-01-01

    Motor vehicle collisions are the leading cause of death for children ages 5 to 14. Enhancement of child occupant protection is partly dependent on the ability to accurately assess the interaction of child-size occupants with restraint systems. Booster seat design and belt fit are evaluated using child anthropomorphic test devices, such as the Hybrid III 6-year-old dummy., A biofidelic abdomen for the Hybrid III 6-year-old dummy is being developed by the Ford Motor Company to enhance the dummy’s ability to assess injury risk and further quantify submarining risk by measuring abdominal deflection. A practical measurement system for the biofidelic abdominal insert has been developed and demonstrated for three dimensional determination of abdominal deflection. Quantification of insert deflection is achieved via differential signal measurement using electrodes mounted within a conductive medium. Signal amplitude is proportional to the distance between the electrodes. A microcontroller is used to calculate distances between ventral electrodes and a dorsal electrode in three dimensions. This system has been calibrated statically, and its performance demonstrated in a series of sled tests. Deflection measurements from the instrumented abdominal insert indicate performance differences between two booster seat designs, yielding an average peak anterior to posterior displacement of the abdomen of 1.0 ± 3.4 mm and 31.2 ± 7.2 mm for the seats, respectively. Implementation of a 6-year-old abdominal insert with the ability to evaluate submarining potential will likely help safety researchers further enhance booster seat design and interaction with vehicle restraint systems , and help to further understand child occupant injury risk in automobile collisions.

  19. Deflecting cavity dynamics for time-resolved machine studies of SXFEL user facility

    CERN Document Server

    Song, Minghao; Liu, Bo; Wang, Dong

    2016-01-01

    Radio frequency deflectors are widely used for time-resolved electron beam energy, emittance and radiation profile measurements in modern free electron laser facilities. In this paper, we present the beam dynamics aspects of the deflecting cavity of SXFEL user facility, which is located at the exit of the undulator. With a targeted time resolution around 10 fs, it is expected to be an important tool for time-resolved commissioning and machine studies for SXFEL user facility.

  20. Deflection and focusing of charged particles by cavities of general shape

    Science.gov (United States)

    Hinderer, G.

    1991-04-01

    The integrated transverse momentum change of a charged particle in the rf field of a cavity can be related to the change of its voltage gain due to a virtual transverse displacement of its orbit. Formulas for the particle deflection are derived, which are a generalisation of the Panofsky-Wenzel theorem to an arbitrary cavity shape and to curved orbits through the cavity. In addition, some useful formulas for the transverse and longitudinal focusing are presented.

  1. Broadband terahertz wave deflection based on C-shape complex metamaterials with phase discontinuities

    KAUST Repository

    Zhang, Xueqian

    2013-06-21

    A broadband terahertz wave deflector based on metasurface induced phase discontinuities is reported. Various frequency components ranging from 0.43 to 1.0 THz with polarization orthogonal to the incidence are deflected into a broad range of angles from 25° to 84°. A Fresnel zone plate consequently developed from the beam deflector is capable of focusing a broadband terahertz radiation. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Ion Deflection for Final Optics In Laser Inertial Fusion Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Abbott, R P; Latkowski, J F

    2006-11-17

    Left unprotected, both transmissive and reflective final optics in a laser inertial fusion power plant would quickly fail from melting, pulsed thermal stresses, or degradation of optical properties as a result of ion implantation. One potential option for mitigating this threat is to magnetically deflect the ions such that they are directed into a robust energy dump. In this paper we detail integrated studies that have been carried out to asses the viability of this approach for protecting final optics.

  3. Toward Identifying Needed Investments in Modeling and Simulation Tools for NEO Deflection Planning

    Science.gov (United States)

    Adams, Robert B.

    2009-01-01

    Its time: a) To bring planetary scientists, deflection system investigators and vehicle designers together on the characterization/mitigation problem. b) To develop a comprehensive trade space of options. c) To trade options under a common set of assumptions and see what comparisons on effectiveness can be made. d) To explore the synergy that can be had with proposed scientific and exploration architectures while interest in NEO's are at an all time high.

  4. Optical Spectroscopy

    DEFF Research Database (Denmark)

    Thyrhaug, Erling

    The work presented in this thesis is broadly concerned with how complexation reactions and molecular motion can be characterized with the standard techniques in optical spectroscopy. The thesis aims to show a relatively broad range of methods for probing physico-chemical properties in fluorophore...... containing systems and are characterized using techniques in optical spectroscopy. Of the standard techniques in optical spectroscopy, particular attention has been paid to those based on time-resolved measurements and polarization, which is reflected in the experiment design in the projects. Not all...... reactions by optical spectroscopy. In project 1 simple steady-state absorption and fluorescence spectroscopy is used to determine the stoichiometries and equilibrium constants in the inclusion complex formation between cyclodextrins and derivatives of the water-insoluble oligo(phenylene vinylene) in aqueous...

  5. Detecting Local Deflection Patterns of Ultra-high Energy Cosmic Rays using the Principal Axes of the Directional Energy Distribution

    CERN Document Server

    Erdmann, Martin

    2013-01-01

    From deflections in galactic and extragalactic magnetic fields energy dependent structures in the arrival directions of ultra-high energy cosmic rays (UHECR) are expected. We propose to characterize these structures by the strength of collimation of energy along the principal axes in selected regions in the sky. While the strength of collimation are indicators of anisotropy in the arrival distribution of UHECR, the orientation of the principal system holds information about the direction of the deflections of UHECR. We discuss the method and present expected limits on the strength of deflection and density of sources using simulated scenarios of UHECR proton propagation.

  6. Diffusion-induced deflection and the effect of two-wave mixing gain on dissipative photovoltaic solitons

    Institute of Scientific and Technical Information of China (English)

    Liu Shi-Xiong; Liu Jin-Song; Zhang Hui-Lan; Zhang Guang-Yong; Wang Cheng

    2007-01-01

    In an open-circuit dissipative photovoltaic (PV) crystal, by considering the diffusion effect, the deflection of bright dissipative photovoltaic (DPV) solitons has been investigated by employing numerical technique and perturbational procedure. The relevant results show that the centre of the optical beam moves along a parabolic trajectory, while the central spatial-frequency component shifts linearly with the propagation distance; furthermore, both the spatial deflection and the angular derivation are associated with the photovoltaic field. Such DPV solitons have a fixed deflection degree completely determined by the parameters of the dissipative system. The small bending cannot affect the formation of the DPV soliton via two-wave mixing.

  7. The Influence of Radiation Damage on the Deflection of High-Energy Beams in Bent Silicon Crystals

    CERN Document Server

    Biino, C; Doble, Niels T; Elsener, K; Gatignon, L; Grafström, P; Mikkelsen, U; Kirsebom, K; Møller, S P; Uggerhøj, Erik; Worm, T

    1996-01-01

    Experimental results obtained for deflection of 450 GeV/c protons channeling along the {111} planes in a bent, strongly irradiated silicon crystal are presented. A comparison between the deflection efficiencies in irradiated areas and non-irradiated areas in the crystal shows that irradiation by 2.4 · 1020 protons/cm2 leads to a reduction of around 30 % in deflection efficiency. As a consequence, beam-splitting and extraction from an accelerator by means of a bent crystal are feasible solutions at high energies even for intense beams and during long periods.

  8. High-efficiency deflection of high energy protons due to channeling along the axis of a bent silicon crystal

    Science.gov (United States)

    Scandale, W.; Arduini, G.; Butcher, M.; Cerutti, F.; Garattini, M.; Gilardoni, S.; Lechner, A.; Masi, A.; Mirarchi, D.; Montesano, S.; Redaelli, S.; Rossi, R.; Smirnov, G.; Breton, D.; Burmistrov, L.; Chaumat, V.; Dubos, S.; Maalmi, J.; Puill, V.; Stocchi, A.; Bagli, E.; Bandiera, L.; Germogli, G.; Guidi, V.; Mazzolari, A.; Dabagov, S.; Murtas, F.; Addesa, F.; Cavoto, G.; Iacoangeli, F.; Galluccio, F.; Afonin, A. G.; Chesnokov, Yu. A.; Durum, A. A.; Maisheev, V. A.; Sandomirskiy, Yu. E.; Yanovich, A. A.; Kovalenko, A. D.; Taratin, A. M.; Denisov, A. S.; Gavrikov, Yu. A.; Ivanov, Yu. M.; Lapina, L. P.; Malyarenko, L. G.; Skorobogatov, V. V.; James, T.; Hall, G.; Pesaresi, M.; Raymond, M.

    2016-09-01

    A deflection efficiency of about 61% was observed for 400 GeV/c protons due to channeling, most strongly along the axis of a bent silicon crystal. It is comparable with the deflection efficiency in planar channeling and considerably larger than in the case of the axis. The measured probability of inelastic nuclear interactions of protons in channeling along the axis is only about 10% of its amorphous level whereas in channeling along the (110) planes it is about 25%. High efficiency deflection and small beam losses make this axial orientation of a silicon crystal a useful tool for the beam steering of high energy charged particles.

  9. A Modified Model for Deflection Calculation of Reinforced Concrete Beam with Deformed GFRP Rebar

    Directory of Open Access Journals (Sweden)

    Minkwan Ju

    2016-01-01

    Full Text Available The authors carried out experimental and analytical research to evaluate the flexural capacity and the moment-deflection relationship of concrete beams reinforced with GFRP bars. The proposed model to predict the effective moment of inertia for R/C beam with GFRP bars was developed empirically, based on Branson’s equation to have better accuracy and a familiar approach to a structural engineer. For better prediction of the moment-deflection relationship until the ultimate strength is reached, a nonlinear parameter (k was also considered. This parameter was introduced to reduce the effect of the cracked moment of inertia for the reinforced concrete member, including a lower reinforcement ratio and modulus of elasticity of the GFRP bar. In a comparative study using six equations suggested by others, the proposed model showed better agreement with the experimental test results. It was confirmed that the empirical modification based on Branson’s equation was valid for predicting the effective moment of inertia of R/C beams with GFRP bar in this study. To evaluate the generality of the proposed model, a comparative study using previous test results from the literature and the results from this study was carried out. It was found that the proposed model had better accuracy and was a familiar approach to structural engineers to predict and evaluate the deflection behavior.

  10. On Possibility of Direct Asteroid Deflection by Electric Solar Wind Sail

    Science.gov (United States)

    Merikallio, Sini; Janhunen, Pekka

    2010-05-01

    The Electric Solar Wind Sail (E-sail) is a new propulsion method for interplanetary travel which was invented in 2006 and is currently under development. The E-sail uses charged tethers to extract momentum from the solar wind particles to obtain propulsive thrust. According to current estimates, the E-sail is 2-3 orders of magnitude better than traditional propulsion methods (chemical rockets and ion engines) in terms of produced lifetime-integrated impulse per propulsion system mass. Here we analyze the problem of using the E-sail for directly deflecting an Earth-threatening asteroid. The problem then culminates into how to attach the E-sail device to the asteroid. We assess a number of alternative attachment strategies and arrive at a recommendation of using the gravity tractor method because of its workability for a wide variety of asteroid types. We also consider possible techniques to scale up the E-sail force beyond the baseline one Newton level to deal with more imminent or larger asteroid or cometary threats. As a baseline case we consider a 3 million ton asteroid which can be deflected with a baseline 1 N E-sail in 5-10 years. Once developed, the E-sail would appear to provide a safe and reasonably low-cost way of deflecting dangerous asteroids and other heavenly bodies in cases where the collision threat becomes known several years in advance.

  11. Deflections of Fast Coronal Mass Ejections and the Properties of Associated Solar Energetic Particle Events

    Science.gov (United States)

    Kahler, S. W.; Akiyama, S.; Gopalswamy, N.

    2012-01-01

    The onset times and peak intensities of solar energetic particle (SEP) events at Earth have long been thought to be influenced by the open magnetic fields of coronal holes (CHs). The original idea was that a CH lying between the solar SEP source region and the magnetic footpoint of the 1 AU observer would result in a delay in onset and/or a decrease in the peak intensity of that SEP event. Recently, Gopalswamy et al. showed that CHs near coronal mass ejection (CME) source regions can deflect fast CMEs from their expected trajectories in space, explaining the appearance of driverless shocks at 1 AU from CMEs ejected near solar central meridian (CM). This suggests that SEP events originating in CME-driven shocks may show variations attributable to CH deflections of the CME trajectories. Here, we use a CH magnetic force parameter to examine possible effects of CHs on the timing and intensities of 41 observed gradual E approx 20 MeV SEP events with CME source regions within 20 deg. of CM. We find no systematic CH effects on SEP event intensity profiles. Furthermore, we find no correlation between the CME leading-edge measured position angles and SEP event properties, suggesting that the widths of CME-driven shock sources of the SEPs are much larger than the CMEs. Independently of the SEP event properties, we do find evidence for significant CME deflections by CH fields in these events

  12. Evaluation of force released by deflection of orthodontic wires in conventional and self-ligating brackets

    Science.gov (United States)

    Higa, Rodrigo Hitoshi; Semenara, Nayara Thiago; Henriques, José Fernando Castanha; Janson, Guilherme; Sathler, Renata; Fernandes, Thais Maria Freire

    2016-01-01

    ABSTRACT Introduction: The aim of the study was to evaluate deflection forces of rectangular orthodontic wires in conventional (MorelliTM), active (In-Ovation RTM) and passive (Damon 3MXTM) self-ligating brackets. Material and Methods: Two brands of stainless steel and nickel-titanium (NiTi) wires (MorelliTM and GACTM), in addition to OrmcoTM copper-nickel-titanium wires were used. Specimens were assembled in a clinical simulation device especially designed for this study and tested in an Instron universal testing machine. For the testing procedures, an acrylic structure representative of the maxillary right central incisor was lingually moved in activations of 0 to 1 mm, with readings of the force released by deflection in unloading of 0.5, 0.8 and 1 mm at a constant speed of 2 mm/min. Inter-bracket forces with stainless steel, NiTi and CuNiTi were individually compared by two-way ANOVA, followed by Tukey’s tests. Results: Results showed that there were lower forces in conventional brackets, followed by active and passive self-ligating brackets. Within the brands, only for NiTi wires, the MorelliTM brand presented higher forces than GACTM wires. Conclusions: Bracket systems provide different degrees of deflection force, with self-ligating brackets showing the highest forces. PMID:28125144

  13. Effects of salicylate on sound-evoked outer hair cell stereocilia deflections.

    Science.gov (United States)

    Hakizimana, Pierre; Fridberger, Anders

    2015-09-01

    Hearing depends on sound-evoked deflections of the stereocilia that protrude from the sensory hair cells in the inner ear. Although sound provides an important force driving stereocilia, forces generated through mechanically sensitive ion channels and through the motor protein prestin have been shown to influence stereocilia motion in solitary hair cells. While a possible influence of prestin on mechanically sensitive ion channels has not been systematically investigated, a decrease in transducer currents is evident in solitary hair cells when prestin is blocked with salicylate, raising the question of whether a reduced prestin activity or salicylate itself affected the mechanotransduction apparatus. We used two- and three-dimensional time-resolved confocal imaging to visualize outer hair cell stereocilia during sound stimulation in the apical turn of cochlear explant preparations from the guinea pig. Surprisingly, following application of salicylate, outer hair cell stereocilia deflections increased, while cochlear microphonic potentials decreased. However, when prestin activity was altered with the chloride ionophore tributyltin, both the cochlear microphonic potential and the stereocilia deflection amplitude decreased. Neither positive nor negative current stimulation abolished the bundle movements in the presence of salicylate, indicating that the observed effects did not depend on the endocochlear potential. These data suggest that salicylate may alter the mechanical properties of stereocilia, decreasing their bending stiffness.

  14. A note on the deflection of a baroclinic current by a continental shelf

    Science.gov (United States)

    Hsueh, Y.; Zhong, Liejun

    2003-05-01

    The deflection, at a step-shelf fronted coast, of a constant potential vorticity current in a reduced-gravity, inviscid model ocean is studied theoretically. The step shelf, with a depth smaller than the reservoir depth, forces the uplifting of the approaching current and causes water column foreshortening, leading to relative vorticity generation that enhances current deflection to the right (facing the coast). As a consequence, in comparison to the case of a vertical wall coast, the proportion of the transport to the right is increased. For normal incidence for a shelf-depth/reservoir-depth ratio of 0.3 and shelf width to deformation radius ratio of 1.5, more than 90% of the approaching current transport goes to the right and less than 10% to the left. In addition, the (barotropic) dynamic pressure at the coast is low to the right and high to the left (with the highest pressure at the stagnation point). In the vertical wall case, the wall pressures on the flank are equal. For oblique incidence from the left, the deflection to the left is drastically reduced. In fact, there is practically no steady-state flow diverted to the left (less than 2%) when the approach angle is greater than 60° to the left of normal. In the vertical wall case, the same angle would have to be 90° for the flow to the left to vanish, namely only when the approach current is parallel to the coast to the right.

  15. Evaluation of force released by deflection of orthodontic wires in conventional and self-ligating brackets

    Directory of Open Access Journals (Sweden)

    Rodrigo Hitoshi Higa

    Full Text Available ABSTRACT Introduction: The aim of the study was to evaluate deflection forces of rectangular orthodontic wires in conventional (MorelliTM, active (In-Ovation RTM and passive (Damon 3MXTM self-ligating brackets. Material and Methods: Two brands of stainless steel and nickel-titanium (NiTi wires (MorelliTM and GACTM, in addition to OrmcoTM copper-nickel-titanium wires were used. Specimens were assembled in a clinical simulation device especially designed for this study and tested in an Instron universal testing machine. For the testing procedures, an acrylic structure representative of the maxillary right central incisor was lingually moved in activations of 0 to 1 mm, with readings of the force released by deflection in unloading of 0.5, 0.8 and 1 mm at a constant speed of 2 mm/min. Inter-bracket forces with stainless steel, NiTi and CuNiTi were individually compared by two-way ANOVA, followed by Tukey’s tests. Results: Results showed that there were lower forces in conventional brackets, followed by active and passive self-ligating brackets. Within the brands, only for NiTi wires, the MorelliTM brand presented higher forces than GACTM wires. Conclusions: Bracket systems provide different degrees of deflection force, with self-ligating brackets showing the highest forces.

  16. Analysis of the deflection of a strut-type lattice girder truss

    Directory of Open Access Journals (Sweden)

    M.N. Kirsanov

    2015-09-01

    Full Text Available The analytical dependence of the deflection of a statically determinate plane elastic truss with a uniform loading of the upper zone has been found. Forces in rods were determined using the joint isolation method. A system of equilibrium equations has been compiled in matrix form. Midspan deflection has been calculated based on the Maxwell-Mohr formula. All character conversion has been executed in the Maple computer algebra system. The method of induction on the number of panels in the truss was used. Recurrent equations for general members of the sequences of coefficients were obtained and solved using the genfunc operators package from the Maple system. The dependencies of the forces in the rods of the truss and of its deflection on the number of panels are non-monotonic, which is generally characteristic of lattice struts. We have also shown that for an odd number of panels the truss is instantaneously variable. The distribution of possible nodal velocities is given for this case.

  17. North-South asymmetry in the magnetic deflection of polar coronal hole jets

    CERN Document Server

    Nistico', Giuseppe; Patsourakos, Spiros; Bothmer, Volker; Nakariakov, Valery M

    2015-01-01

    Measurements of the magnetic field in the interplanetary medium, of the sunspots area, and of the heliospheric current sheet position, reveal a possible North-South asymmetry in the magnetic field of the Sun. We study the North-South asymmetry as inferred from measurements of the deflection of polar coronal hole jets when they propagate throughout the corona. Since the corona is an environment where the magnetic pressure is greater than the kinetic pressure, we can assume that magnetic field controls the dynamics of plasma. On average, jets during their propagation follow the magnetic field lines, highlighting its local direction. The average jet deflection is studied both in the plane perpendicular to the line of sight, and, for a reduced number of jets, in three dimensional space. The observed jet deflection is studied in terms of an axisymmetric magnetic field model comprising dipole We measured the position angles at 1 rs and at 2 rs of the 79 jets from the catalogue of Nistico et al 2009., based on the S...

  18. Challenges of deflecting an asteroid or comet nucleus with a nuclear burst

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, Paul A [Los Alamos National Laboratory; Plesko, Cathy S [Los Alamos National Laboratory; Clement, Ryan R. C. [Los Alamos National Laboratory; Conlon, Le Ann M [Los Alamos National Laboratory; Weaver, Robert P [Los Alamos National Laboratory; Guzik, Joyce A [Los Alamos National Laboratory; Pritchett - Sheets, Lori A [Los Alamos National Laboratory; Huebner, Walter F [SWRI

    2009-01-01

    There are many natural disasters that humanity has to deal with over time. These include earthquakes, tsunamis, hurricanes, floods, asteroid strikes, and so on. Some of these disasters occur slowly enough that some advance warning is possible for affected areas. In this case, the response is to evacuate the affected area and deal wilh the damage later. The Katrina and Rita hurricane evacuations on the U.S. Gulf Coasl in 2005 demonstrated the chaos that can result from such a response. In contrast with other natural disasters, it is likely that an asteroid or comet nucleus on a collision course with Earth will be detected with enough warning time to possibly deflect it away. Thanks to Near-Earth Object (NED) surveys, people are working towards a goal of cataloging at least 90% of all near-Earth objects with diameters larger than {approx} 140 meters in the next fifteen years. The important question then, is how to mitigate the threat from an asteroid or comet nucleus found to be on a collision course with Earth. In this paper. we briefly review some possible deflection methods, describe their good and bad points, and then embark on a more detailed description of using nuclear munitions in a standoff mode to deflect the asteroid or comet nucleus before it can hit Earth.

  19. Dynamics and control of a solar collector system for near Earth object deflection *

    Institute of Scientific and Technical Information of China (English)

    Shen-Ping Gong; Jun-Feng Li; Yun-Feng Gao

    2011-01-01

    A solar collector system is a possible method using solar energy to deflect Earth-threatening near-Earth objects. We investigate the dynamics and control of a solar collector system including a main collector (MC) and secondary collector (SC).The MC is used to collect the sunlight to its focal point, where the SC is placed and directs the collected light to an asteroid. Both the relative position and attitude of the two collectors should be accurately controlled to achieve the desired optical path. First,the dynamical equation of the relative motion of the two collectors in the vicinity of the asteroid is modeled. Secondly, the nonlinear sliding-mode method is employed to design a control law to achieve the desired configuration of the two collectors. Finally,the deflection capability of this solar collector system is compared with those of the gravitational tractor and solar sail gravitational tractor. The results show that the solar collector is much more efficient with respect to deflection capability.

  20. Eddies and a mesoscale deflection of the slope current in the Faroe Shetland Channel

    Science.gov (United States)

    Sherwin, T. J.; Turrell, W. R.; Jeans, D. R. G.; Dye, S.

    1999-03-01

    The mesoscale dynamics of the Scottish side of the Faroe-Shetland Channel have been investigated using synoptic in situ and remote sensing observations. A cold core cyclonic eddy, identified from an AVHRR image, had a diameter of about 50 km and surface current speeds of up to 50 cm s -1; it appeared to be attached to the 800 m isobath as it moved north-eastward along the edge of the channel at about 8 cm s -1. Speeds in the slope current were about 50 cm s -1 but increased to 70 cm s -1 where the current was compressed by the eddy. Offshore, over the 1000 m isobath in the cooler water, speeds in the current were slower (ca. 20 cm s -1). North-west of the Shetlands the offshore edge of the slope current was deflected across the channel for a distance of about 70 km from the shelf edge. The speed of drifters in the slope current increased to over 60 cm s -1 as they moved anti-cyclonically around this deflection. CTD profiles suggest that the movement of the surface waters was mirrored in the deep water of the channel. The deflection carried a very large quantity of North Atlantic Water into the central part of the channel; its cause and ultimate fate are not known, although it is likely to have had a significant impact on the dynamics of the channel.

  1. A Two-Dimensional Deflection Sensor Based on Force Sensing Resistors

    Directory of Open Access Journals (Sweden)

    Chuangqiang Guo

    2017-01-01

    Full Text Available A flexible deflection sensor for elastic shaft with the capability of measuring the amplitude and direction of bending is introduced in this paper. A thin force sensing resistors (FSR film is taken as its basic material, which is sandwiched by an elastomer layer and a printed circuit board (PCB with detecting electrode grids. Two fix rings are used to fix the three thin components perpendicularly to the longitudinal direction of the flexible shaft. When the shaft bends under forces, the fix rings will generate a normal pressure on FSR, which will cause the change of the resistance. Therefore, the amplitude of bending can be got based on the value of resistance. The electrode grid on the PCB is divided into four detection areas used to estimate the distribution of normal pressure on the FSR; thus the bending direction of shaft can also be obtained. Test results of a prototype (140 mm in length show that the amplitude of deflection can reach 30 mm and the sensitivities of sensor are 40.37, 32.8, 37.77, and 39.47 mV/mm in the four directions, respectively. The proposed flexible deflection sensor can be applied in continuum robots or other applications, which require rapid measurement of bending amplitude and direction.

  2. Cupula displacement, hair bundle deflection, and physiological responses in the transparent semicircular canal of young eel.

    Science.gov (United States)

    Rüsch, A; Thurm, U

    1989-03-01

    The transparent labyrinth of young eels (Anguilla anguilla L.) was used in toto for studying the configuration of cupula displacement, deflection of the hair bundle, and correlated changes in transepithelial voltage (delta TEV) and nerve activity (delta NA) in the semicircular canal. Microcapillaries were introduced into the canal through holes produced by a microthermocauter. Mechanical stimulation was applied either by injection of fluid into the ampulla or by electromagnetically displacing ferrofluid as a piston within the canal. Motion of individual kinocilia, stained cupulae or the ferrofluid piston was analysed by double-exposed microphotographs, photodiodes, or a video-system. The three-dimensional cupula displacement configuration was found to be piston- to diaphragm-like. Hair bundles at different sites on the crista exhibit differences in amplitude and time course of deflection. The transfer factor between shifts of the canal fluid and the tips of the kinocilia is 0.4-0.6. Displacements in opposite directions induce delta TEV and delta NA of opposite sign. Various tests confirmed delta TEV to reflect receptor potential responses. Nerve activity adapts to a tonic response with a time constant of 6.4 s. No similar adaptation occurred in delta TEV. Stimulus-response curves of TEV- and NA-responses are similar and sigmoid in shape with saturation at ciliary deflections of roughly +6 degrees and -3 degrees.

  3. RF deflecting cavity design for Berkeley ultrafast X-ray source

    Science.gov (United States)

    Li, D.; Corlett, J.

    2002-05-01

    Our proposed source for production of ultra-short (less than 100 fs FWHM) x-ray pulses utilizes a scheme for manipulation of the relatively long (2 ps) electron bunch in transverse phase-space, followed by compression of the emitted x-ray pulse in crystal optics. In order to compress the x-ray pulses, RF cavities operating in a dipole mode (TM110-like) are required to deflect the head and tail of a 2.5 GeV bunch in opposite directions. For a 2 ps duration electron bunch, an 8.5 MV deflecting voltage is required at a RF frequency of 3.9 GHz. In this paper, we will present a preliminary cavity design based on numerical simulations performed by MAFIA and URMEL codes. Seven-cell superconducting p mode dipole RF cavities are proposed to provide the necessary deflecting voltage. Due to the presence of beam iris, the mavities operate in a hybrid mode where TM and TE like modes co-exist. Even on mhe beam axis, both magnetic and electric fields contribute to the transverse mick. Lower order monopole modes (LOMs) in the cavities may cause energy spread of the electron beam and need to be damped. The effects of the LOMs on beam dynamics are estimated. Possible damping schemes will be discussed.

  4. RF deflecting cavity design for Berkeley ultrafast X-ray source

    Energy Technology Data Exchange (ETDEWEB)

    Li, Derun; Corlett, J.

    2002-05-30

    Our proposed source for production of ultra-short (less than 100 fs FWHM) x-ray pulses utilizes a scheme for manipulation of the relatively long ({approx}2 ps) electron bunch in transverse phase-space, followed by compression of the emitted x-ray pulse in crystal optics [1]. In order to compress the x-ray pulses, RF cavities operating in a dipole mode (TM{sub 110}-like) are required to deflect the head and tail of a 2.5 GeV bunch in opposite directions. For a 2 ps duration electron bunch, an 8.5 MV deflecting voltage is required at a RF frequency of 3.9 GHz. In this paper, we will present a preliminary cavity design based on numerical simulations performed by MAFIA and URMEL codes. Seven-cell superconducting {pi} mode dipole RF cavities are proposed to provide the necessary deflecting voltage. Due to the presence of beam iris, the cavities operate in a hybrid mode where TM and TE like modes co-exist. Even on the beam axis, both magnetic and electric fields contribute to the transverse kick. Lower order monopole modes (LOMs) in the cavities may cause energy spread of the electron beam and need to be damped. The effects of the LOMs on beam dynamics are estimated. Possible damping schemes will be discussed.

  5. Smart earthquake-resistant materials: using time-released adhesives for damping, stiffening, and deflection control

    Science.gov (United States)

    Dry, Carolyn M.

    1996-04-01

    Preventing buildings and bridges from damage from severe dynamic loading events is a primary goal of civil infrastructure. Present designs attempt to control structural response by making the structures more massive, by increasing lateral stiffness through bracing, and by damping technology such as mass damping and base-isolation. These attempts affect portions of the governing equation: for an idealized building frame or bridge, the free vibrational behavior is described by Mu + cu + ku equals -mug(t) where m equals mass, c equals damping coefficient, k equals lateral stiffness, u equals deflection, and ug(t) equals ground acceleration. The use of adhesive released internally in a material based way of addressing the problem. The time release of low modulus adhesive chemicals would assist the damping characteristics of the structure, use of a stiffer adhesive would allow the damaged structure to regain some lateral stiffness (k) and adjustment of the set times of the adhesives would act to control the deflection. These can be thought of as potential new method of controlling vibration of behavior in case of a dynamic loading event. In past experiments, self-healing concrete matrices were shown to increase post-yield deflection and load carrying capability by the release and setting of adhesives. The results were promising in resisting damage of dynamic loads applied to frames. This indicates that self-healing concrete would be extremely valuable in civil engineering structures that were subjected to failure-inducing loads such as earthquakes.

  6. Rotational and translational considerations in kinetic impact deflection of potentially hazardous asteroids

    Science.gov (United States)

    Zhang, Fei; Xu, Bo; Circi, Christian; Zhang, Lei

    2017-04-01

    Kinetic impact may be the most reliable and easily implemented method to deflect hazardous asteroids using current technology. Depending on warning time, it can be effective on asteroids with diameters of a few hundred meters. Current impact deflection research often focuses on the orbital dynamics of asteroids. In this paper, we use the ejection outcome of a general oblique impact to calculate how an asteroid's rotational and translational state changes after impact. The results demonstrate how small impactors affect the dynamical state of small asteroids having a diameter of about 100 m. According to these consequences, we propose using several small impactors to hit an asteroid continuously and gently, making the deflection mission relatively flexible. After calculating the rotational variation, we find that the rotational state, especially of slender non-porous asteroids, can be changed significantly. This gives the possibility of using multiple small impactors to mitigate a potentially hazardous asteroid by spinning it up into pieces, or to despin one for future in-situ investigation (e.g., asteroid retrieval or mining).

  7. Study of Tensile Properties and Deflection Temperature of Polypropylene/Subang Pineapple Leaf Fiber Composites

    Science.gov (United States)

    Hafizhah, R.; Juwono, A. L.; Roseno, S.

    2017-05-01

    The development of eco-friendly composites has been increasing in the past four decades because the requirement of eco-friendly materials has been increasing. Indonesia has a lot of natural fiber resources and, pineapple leaf fiber is one of those fibers. This study aimed to determine the influence of weight fraction of pineapple leaf fibers, that were grown at Subang, to the tensile properties and the deflection temperature of polypropylene/Subang pineapple leaf fiber composites. Pineapple leaf fibers were pretreated by alkalization, while polypropylene pellets, as the matrix, were extruded into sheets. Hot press method was used to fabricate the composites. The results of the tensile test and Heat Deflection Temperature (HDT) test showed that the composites that contained of 30 wt.% pineapple leaf fiber was the best composite. The values of tensile strength, modulus of elasticity and deflection temperature were (64.04 ± 3.91) MPa; (3.98 ± 0.55) GPa and (156.05 ± 1.77) °C respectively, in which increased 187.36%, 198.60%, 264.72% respectively from the pristine polypropylene. The results of the observation on the fracture surfaces showed that the failure modes were fiber breakage and matrix failure.

  8. Laser spectroscopy

    CERN Document Server

    Demtröder, Wolfgang

    Keeping abreast of the latest techniques and applications, this new edition of the standard reference and graduate text on laser spectroscopy has been completely revised and expanded. While the general concept is unchanged, the new edition features a broad array of new material, e.g., ultrafast lasers (atto- and femto-second lasers) and parametric oscillators, coherent matter waves, Doppler-free Fourier spectroscopy with optical frequency combs, interference spectroscopy, quantum optics, the interferometric detection of gravitational waves and still more applications in chemical analysis, medical diagnostics, and engineering.

  9. Self-deflection of bright soliton in a separate bright-dark screening soliton pair based on higher-order space charge field

    Institute of Scientific and Technical Information of China (English)

    Zhonghua Hao(郝中华); Jinsong Liu(刘劲松)

    2003-01-01

    Based on the interaction of the separate soliton pair, the self-deflection of the bright screening soliton in a bright-dark pair is studied by taking the higher order space charge field into account. Both numerical and analytical methods are adopted to obtain the result that the higher order of space charge field can enhance the deflection process of the bright soliton and varying the peak intensity of the dark soliton can influence the self-deflection strongly. The expression of the deflection distance with the dark soliton's peak intensity is derived, and some corresponding properties of the self-deflection process are figured out.

  10. The Significance of the Influence of the CME Deflection in Interplanetary Space on the CME Arrival at Earth

    Science.gov (United States)

    Zhuang, Bin; Wang, Yuming; Shen, Chenglong; Liu, Siqing; Wang, Jingjing; Pan, Zonghao; Li, Huimin; Liu, Rui

    2017-08-01

    As one of the most violent astrophysical phenomena, coronal mass ejections (CMEs) have strong potential space weather effects. However, not all Earth-directed CMEs encounter the Earth and produce geo-effects. One reason is the deflected propagation of CMEs in interplanetary space. Although there have been several case studies clearly showing such deflections, it has not yet been statistically assessed how significantly the deflected propagation would influence the CME’s arrival at Earth. We develop an integrated CME-arrival forecasting (iCAF) system, assembling the modules of CME detection, three-dimensional (3D) parameter derivation, and trajectory reconstruction to predict whether or not a CME arrives at Earth, and we assess the deflection influence on the CME-arrival forecasting. The performance of iCAF is tested by comparing the two-dimensional (2D) parameters with those in the Coordinated Data Analysis Workshop (CDAW) Data Center catalog, comparing the 3D parameters with those of the gradual cylindrical shell model, and estimating the success rate of the CME Earth-arrival predictions. It is found that the 2D parameters provided by iCAF and the CDAW catalog are consistent with each other, and the 3D parameters derived by the ice cream cone model based on single-view observations are acceptable. The success rate of the CME-arrival predictions by iCAF with deflection considered is about 82%, which is 19% higher than that without deflection, indicating the importance of the CME deflection for providing a reliable forecasting. Furthermore, iCAF is a worthwhile project since it is a completely automatic system with deflection taken into account.

  11. Fluorescence spectroscopy

    DEFF Research Database (Denmark)

    Bagatolli, Luis

    2016-01-01

    Fluorescence spectroscopy is a powerful experimental tool used by scientists from many disciplines. During the last decades there have been important developments on distinct fluorescence methods, particularly those related to the study of biological phenomena. This chapter discusses...

  12. Analysis on the Deflection Angle of Columnar Dendrites of Continuous Casting Steel Billets Under the Influence of Mold Electromagnetic Stirring

    Science.gov (United States)

    Wang, Xincheng; Wang, Shengqian; Zhang, Lifeng; Sridhar, Seetharaman; Conejo, Alberto; Liu, Xuefeng

    2016-11-01

    In the current study, the deflection angle of columnar dendrites on the cross section of steel billets under mold electromagnetic stirring (M-EMS) was observed. A mathematical model was developed to define the effect of M-EMS on fluid flow and then to analyze the relationship between flow velocities and deflection angle. The model was validated using experimental data that was measured with a Tesla meter on magnetic intensity. By coupling the numerical results with the experimental data, it was possible to define a relationship between the velocities of the fluid with the deflection angle of high-carbon steel. The deflection angle of high-carbon steel reached maximum values from 18 to 23 deg for a velocity from 0.35 to 0.40 m/s. The deflection angles of low-carbon steel under different EM parameters were discussed. The deflection angle of low-carbon steel was increased as the magnetic intensity, EM force, and velocity of molten steel increased.

  13. MODELING SUPERSONIC-JET DEFLECTION IN THE HERBIG–HARO 110-270 SYSTEM WITH HIGH-POWER LASERS

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Dawei; Li, Yutong; Lu, Xin; Yin, Chuanlei; Su, Luning; Liao, Guoqian; Zhang, Jie [National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China); Wu, Junfeng; Wang, Lifeng; He, Xiantu [Institute of Applied Physics and Computational Mathematics, Beijing 100088 (China); Zhong, Jiayong; Wei, Huigang; Zhang, Kai; Han, Bo; Zhao, Gang [Key Laboratory of Optical Astronomy, National Astronomical Observatories, Chinese Academy of Sciences, Beijing 100012 (China); Jiang, Shaoen; Du, Kai; Ding, Yongkun [Research Center for Laser Fusion, China Academy of Engineering Physics, Mianyang 621900 (China); Zhu, Jianqiang, E-mail: ytli@iphy.ac.cn, E-mail: jzhang@sjtu.edu.cn [National Laboratory on High Power Lasers and Physics, Shanghai, 201800 (China)

    2015-12-10

    Herbig–Haro (HH) objects associated with newly born stars are typically characterized by two high Mach number jets ejected in opposite directions. However, HH 110 appears to only have a single jet instead of two. Recently, Kajdi et al. measured the proper motions of knots in the whole system and noted that HH 110 is a continuation of the nearby HH 270. It has been proved that the HH 270 collides with the surrounding mediums and is deflected by 58°, reshaping itself as HH 110. Although the scales of the astrophysical objects are very different from the plasmas created in the laboratory, similarity criteria of physical processes allow us to simulate the jet deflection in the HH 110/270 system in the laboratory with high power lasers. A controllable and repeatable laboratory experiment could give us insight into the deflection behavior. Here we show a well downscaled experiment in which a laser-produced supersonic-jet is deflected by 55° when colliding with a nearby orthogonal side-flow. We also present a two-dimensional hydrodynamic simulation with the Euler program, LARED-S, to reproduce the deflection. Both are in good agreement. Our results show that the large deflection angle formed in the HH 110/270 system is probably due to the ram pressure from a flow–flow collision model.

  14. Decay-Assisted Laser Spectroscopy of Neutron-Deficient Francium

    CERN Document Server

    Lynch, K M; Bissell, M L; Budincevic, I; Cocolios, T E; De Groote, R P; De Schepper, S; Fedosseev, V N; Flanagan, K T; Franchoo, S; Garcia Ruiz, R F; Heylen, H; Marsh, B A; Neyens, G; Procter, T J; Rossel, R E; Rothe, S; Strashnov, I; Stroke, H H; Wendt, K D A

    2014-01-01

    This paper reports on the hyperfine-structure and radioactive-decay studies of the neutron-deficient francium isotopes $^{202-206}$Fr performed with the Collinear Resonance Ionization Spectroscopy (CRIS) experiment at the ISOLDE facility, CERN. The high resolution innate to collinear laser spectroscopy is combined with the high efficiency of ion detection to provide a highly-sensitive technique to probe the hyperfine structure of exotic isotopes. The technique of decay-assisted laser spectroscopy is presented, whereby the isomeric ion beam is deflected to a decay spectroscopy station for alpha-decay tagging of the hyperfine components. Here, we present the first hyperfine-structure measurements of the neutron-deficient francium isotopes $^{202-206}$Fr, in addition to the identification of the low-lying states of $^{202,204}$Fr performed at the CRIS experiment.

  15. Proton beam deflection in MRI fields: Implications for MRI-guided proton therapy.

    Science.gov (United States)

    Oborn, B M; Dowdell, S; Metcalfe, P E; Crozier, S; Mohan, R; Keall, P J

    2015-05-01

    This paper investigates, via magnetic modeling and Monte Carlo simulation, the ability to deliver proton beams to the treatment zone inside a split-bore MRI-guided proton therapy system. Field maps from a split-bore 1 T MRI-Linac system are used as input to geant4 Monte Carlo simulations which model the trajectory of proton beams during their paths to the isocenter of the treatment area. Both inline (along the MRI bore) and perpendicular (through the split-bore gap) orientations are simulated. Monoenergetic parallel and diverging beams of energy 90, 195, and 300 MeV starting from 1.5 and 5 m above isocenter are modeled. A phase space file detailing a 2D calibration pattern is used to set the particle starting positions, and their spatial location as they cross isocenter is recorded. No beam scattering, collimation, or modulation of the proton beams is modeled. In the inline orientation, the radial symmetry of the solenoidal style fringe field acts to rotate the protons around the beam's central axis. For protons starting at 1.5 m from isocenter, this rotation is 19° (90 MeV) and 9.8° (300 MeV). A minor focusing toward the beam's central axis is also seen, but only significant, i.e., 2 mm shift at 150 mm off-axis, for 90 MeV protons. For the perpendicular orientation, the main MRI field and near fringe field act as the strongest to deflect the protons in a consistent direction. When starting from 1.5 m above isocenter shifts of 135 mm (90 MeV) and 65 mm (300 MeV) were observed. Further to this, off-axis protons are slightly deflected toward or away from the central axis in the direction perpendicular to the main deflection direction. This leads to a distortion of the phase space pattern, not just a shift. This distortion increases from zero at the central axis to 10 mm (90 MeV) and 5 mm (300 MeV) for a proton 150 mm off-axis. In both orientations, there is a small but subtle difference in the deflection and distortion pattern between protons fired parallel to the

  16. Nanoindenting the Chelyabinsk Meteorite to Learn about Impact Deflection Effects in Asteroids

    Science.gov (United States)

    Moyano-Cambero, Carles E.; Pellicer, Eva; Trigo-Rodríguez, Josep M.; Williams, Iwan P.; Blum, Jürgen; Michel, Patrick; Küppers, Michael; Martínez-Jiménez, Marina; Lloro, Ivan; Sort, Jordi

    2017-02-01

    The Chelyabinsk meteorite is a highly shocked, low porosity, ordinary chondrite, probably similar to S- or Q-type asteroids. Therefore, nanoindentation experiments on this meteorite allow us to obtain key data to understand the physical properties of near-Earth asteroids. Tests at different length scales provide information about the local mechanical properties of the minerals forming this meteorite: reduced Young’s modulus, hardness, elastic recovery, and fracture toughness. Those tests are also useful to understand the potential to deflect threatening asteroids using a kinetic projectile. We found that the differences in mechanical properties between regions of the meteorite, which increase or reduce the efficiency of impacts, are not a result of compositional differences. A low mean particle size, attributed to repetitive shock, can increase hardness, while low porosity promotes a higher momentum multiplication. Momentum multiplication is the ratio between the change in momentum of a target due to an impact, and the momentum of the projectile, and therefore, higher values imply more efficient impacts. In the Chelyabinsk meteorite, the properties of the light-colored lithology materials facilitate obtaining higher momentum multiplication values, compared to the other regions described for this meteorite. Also, we found a low value of fracture toughness in the shock-melt veins of Chelyabinsk, which would promote the ejection of material after an impact and therefore increase the momentum multiplication. These results are relevant to the growing interest in missions to test asteroid deflection, such as the recent collaboration between the European Space Agency and NASA, known as the Asteroid Impact and Deflection Assessment mission.

  17. A real-time, nonintrusive trace gas detector based on laser photothermal deflection

    Science.gov (United States)

    de Vries, H. S. M.; Dam, N.; van Lieshout, M. R.; Sikkens, C.; Harren, F. J. M.; Reuss, J.

    1995-09-01

    We present the layout and technical details of a trace gas monitor based on photothermal deflection. The operating principle of this instrument, i.e., the deflection of a (weak) probe laser beam by the thermal refractive index gradient induced by trace gas absorption of an intense pump laser beam, allows nonintrusive measurements with good space and time resolution. An intra-cavity CO2 laser is used as the pump beam and a red HeNe laser as the probe. The latter runs perpendicular to the pump beam to optimize spatial resolution. To increase sensitivity, the probe laser is incorporated in a multipass setup. The instrument is demonstrated by the localization of ethylene emission sites on a cherry tomato and by monitoring ammonia production due to nitrogen fixation by cyanobacteria. Both C2H4 and NH3 can be detected at the 1-3 ppb level, at a spatial resolution of 2 mm (along the pump laser)×0.6 mm (perpendicular to it), and a response time of 0.1 s (without background correction) or 15 s (including background correction). Sensitivity can be increased at the expense of spatial resolution, and vice versa. In principle, this instrument is applicable to all those gases possessing a characteristic (``fingerprint'') spectrum in the CO2 laser range. The great advantage of the photothermal deflection technique with respect to other trace gas detection schemes lies in the nonintrusive character of the measurements. There is no need to enclose the sample in a vessel or to suck large volumes of air into the detector; measurements can be performed in open air and in real time. This should prove especially useful where sticky (polar) gases, like H2O, NH3, CH3OH, etc., are to be detected quantitatively. Main applications include air quality monitoring, especially concerning dry deposition rate measurements using the eddy correlation technique, and the study of volatile metabolite emission of biological samples.

  18. THE EFFECT OF CORRUGATED ELEMENTS THICKNESS ON THE DEFLECTED MODE OF CORRUGATED METAL STRUCTURES

    Directory of Open Access Journals (Sweden)

    V. V. Kovalchuk

    2015-06-01

    Full Text Available Purpose. The work provides research the deflected mode and calculation the relative deformation of vertical and horizontal diameters of corrugated metal structures (CMS, horizontal ellipse type, and cross section in their interaction with soil backfill depending on the thickness of corrugated metal pipe. Such studies are required for optimal design of CMS, establishing the causes of defects timely, appropriate engineering solutions to improve the bearing capacity of the CMS and reasonable use of funds for their construction or rehabilitation of existing transportation facilities using corrugated metal pipes. Methodology. Stresses and stability calculations of CMS form are conducted using the developed mathematical algorithm in program environment Mathcad 14. In these studies different thickness of corrugated metal pipe were assigned, and further calculations were carried out at the design value of backfill soil compaction degree and magnitude of dynamic loading of railway transport. Findings. From the calculations is determined that the most influence the thickness of the corrugated metal pipe has on the strength in the calculation of the normal stresses and value of the vertical pipe strains. Therefore, the calculated parameters in the design of corrugated metal structures with small filling heights (from 1.2 m to 3 m above its peak is calculation of the strength by the normal stresses and determination of the vertical deformation of the pipe. Originality. For the first time, calculations of the deflected mode and relative deformations of vertical and horizontal cross-sectional diameters of CMS, horizontal ellipse type in the interaction with soil backfill. The factors complex was taken into account the backfill soil compaction degree, the value of dynamic loading of railway transport and different thickness of corrugated metal pipe. Practical value. The results of the deflected mode of corrugated metal structures such as horizontal ellipse of

  19. Linearized gravity, Newtonian limit and light deflection in RS1 model

    CERN Document Server

    Smolyakov, M N; Smolyakov, Mikhail N.; Volobuev, Igor P.

    2002-01-01

    We solve exactly the equations of motion for linearized gravity in the Randall-Sundrum model with matter on the branes and calculate the Newtonian limit in it. The result contains contributions of the radion and of the massive modes, which change considerably Newton's law at small distances. The effects of "shadow" matter, which lives on the other brane, are considered and compared with those of ordinary matter for both positive and negative tension branes. We also calculate light deflection and Newton's law in the zero mode approximation and explicitly distinguish the contribution of the radion field.

  20. A Transverse Dynamic Deflection Model for Thin Plate Made of Saturated Porous Materials

    Science.gov (United States)

    Feng-xi, Zhou; Xiao-lin, Cao

    2016-10-01

    In this article, a transverse dynamic deflection model is established for thin plate made of saturated porous materials. Based on the Biot's model for fluid-saturated porous media, using the Love-Kirchhoff hypothesis, the governing equations of transverse vibrations of fluid-saturated poroelastic plates are derived in detail, which take the inertial, fluid viscous, mechanical couplings, compressibility of solid, and fluid into account. The free vibration and forced vibration response of a simply supported poroelastic rectangular plate is obtained by Fourier series expansion method. Through numerical examples, the effect of porosity and permeability on the dynamic response, including the natural frequency, amplitude response, and the resonance areas is assessed.

  1. Application of engineering models to predict wake deflection due to a tilted wind turbine

    DEFF Research Database (Denmark)

    Guntur, Srinivas; Troldborg, Niels; Gaunaa, Mac

    It is a known fact that the power produced by wind turbines operating inside an array decreases due to the wake effects of the upstream turbines. It has been proposed previously to use the yaw mechanism as a potential means to steer the upstream wake away from downstream turbines, however...... such a mechanism introduces control complications due to changing wind directions. Deflecting the wake in the vertical direction using tilt, on the other hand, overcomes this challenge. In this paper, the feasibility of steering wake is explored in a simple uniform inflow case. This is done by trying to model...

  2. Application of engineering models to predict wake deflection due to a tilted wind turbine

    DEFF Research Database (Denmark)

    Guntur, Srinivas; Troldborg, Niels; Gaunaa, Mac

    2012-01-01

    It is a known fact that the power produced by wind turbines operating inside an array decreases due to the wake effects of the upstream turbines. It has been proposed previously to use the yaw mechanism as a potential means to steer the upstream wake away from downstream turbines, however...... such a mechanism introduces control complications due to changing wind directions. Deflecting the wake in the vertical direction using tilt, on the other hand, overcomes this challenge. In this paper, the feasibility of steering wake is explored in a simple uniform inflow case. This is done by trying to model...

  3. Gregory Bateson's lost world: the anthropology of Haddon and Rivers continued and deflected.

    Science.gov (United States)

    Wardle, H

    1999-01-01

    Gregory Bateson was one of the last and most distinguished products of the school of anthropology that Haddon and Rivers created in Cambridge after the Torres Strait Expedition. Beginning his career shortly after Rivers' death, Bateson used the interwar years to create a theoretical approach that continued and deflected that of Haddon and Rivers. His major ethnography from this period, Naven, evidenced his complex academic positioning between the legacy of Rivers and the new paradigm emerging around Malinowski and Radcliffe-Brown. After the Second World War, Bateson's intellectual project emerged as even closer to Rivers' in both psychological and evolutionary dimensions.

  4. Classical and tree-level approaches to gravitational deflection in higher-derivative gravity

    CERN Document Server

    Accioly, Antonio; Giacchini, Breno; Herdy, Wallace

    2015-01-01

    Among the so-called classical tests of general relativity (GR), light bending has been confirmed with an accuracy that increases as times goes by. Here we study the gravitational deflection of photons within the framework of classical and semiclassical higher-derivative gravity (HDG) -- the only version of GR that is known up to now to be renormalizable along with its matter couplings. Since our computations are restricted to scales much below the Planck cut-off we need not be afraid of the massive spin-2 ghost that haunts HDG. An upper bound on the constant related to the $R^2_{\\mu \

  5. On-line monitoring of poly dimethylsiloxane surface modification using the photothermal deflection technique

    Energy Technology Data Exchange (ETDEWEB)

    Najmoddin, Najmeh, E-mail: najmoddin@iust.ac.ir; Khosroshahi, Mohammad E.

    2015-02-21

    Over the last decade, there has been particular interest in surface modification of biomaterials with regard to understanding the importance of surface characterization. This paper reports the use of photothermal deflection (PTD) technique to monitor modifications in poly dimethylsiloxane (PDMS) surface induced following laser treatments. The FTIR results are in agreement with PTD results, indicating that no structural changes occurred using Argon laser up to 180 s and 200 mW at 454, 488 and 514 nm wavelengths. However, with CO{sub 2} laser some physical and chemical changes occurred which are monitored by PTD technique and proved by SEM images.

  6. A New Four States High Deflection Low Actuation Voltage Electrostatic Mems Switch for RF Applications

    CERN Document Server

    Robin, Renaud; Segueni, Karim; Millet, Olivier; Buchaillot, Lionel

    2008-01-01

    This paper presents a new electrostatic MEMS (MicroElectroMechanical System) based on a single high reliability totally free flexible membrane. Using four electrodes, this structure enables four states which allowed large deflections (4$\\mu$m) with low actuation voltage (7,5V). This design presents also a good contact force and improve the restoring force of the structure. As an example of application, a Single Pole Double Throw (SPDT) for 24GHz applications, based on this design, has been simulated.

  7. Generation of Picosecond X-Ray Pulses in the ALS Using RF Orbit Deflection

    CERN Document Server

    Robin, David; Fischer, Peter; Heimann, Philip; Kim, Dong-Hyun; Kwiatkowski, Slawomir; Li, Derun; Sannibale, Fernando; Steier, Christoph; Wan, Weishi; Wittmer, Walter; Zholents, Alexander

    2005-01-01

    A scheme is studied for producing ps length pulses of x-ray radiation from the Advanced Light Source (ALS) using two RF deflecting cavities. The cavities create vertical displacements of electrons correlated with their longitudinal position in the bunch. The two cavities separated by 180 degrees of vertical phase advance. This allows the vertical kick from one cavity to be compensated by the vertical kick of the other. The location of the cavities corresponds to the end of one straight section and the beginning of the following straight section. Halfway between the cavities a bending magnet source is located. The radiation from the bend can be compressed to ~1 ps in duration.

  8. WEIGHTED SOLUTION OF SMALL-DEFLECTION BUCKLING EQUATION OF THIN SHELL

    Institute of Scientific and Technical Information of China (English)

    王宗利; 王熙; 郝文华

    2001-01-01

    Based on small-deflection buckling equation, a weighted solution for critical load is presented. Usually, it is very difficult to solve the equation for general problems,especially those with complicated boundary conditions. Axisymmetric problem was studied as an example. Influencing factors were found from the equation and averaged as the buckling load by introducing weights. To determine those weights, some special known results were applied. This method solves general complicated problems by using the solutions of special simple problems, simplifies the solving procedure and expands the scope of solvable problem. Compared with numerical solution, it also has fine precision.

  9. Slice emittance measurement for photocathode RF gun with solenoid scanning and RF deflecting cavity

    Science.gov (United States)

    Li, Chen; Huang, WenHui; Du, YingChao; Yan, LiXin; Tang, ChuanXiang

    2011-12-01

    The radiation of high-gain short-wavelength free-electron laser depends on the slice transverse emittance of the electron bunch. This essay introduces the method of slice emittance measurement, and shows the brief setup of this experiment using the solenoid scanning and RF deflecting cavity at Tsinghua University. The preliminary experimental results show that the slice rms emittance of the electron bunch generated by photocathode RF gun has considerable variations along the bunch and is typically less than 0.55 mm mrad for the laser rms radius of 0.4 mm.

  10. Slice emittance measurement for photocathode RF gun with solenoid scanning and RF deflecting cavity

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    The radiation of high-gain short-wavelength free-electron laser depends on the slice transverse emittance of the electron bunch. This essay introduces the method of slice emittance measurement, and shows the brief setup of this experiment using the solenoid scanning and RF deflecting cavity at Tsinghua University. The preliminary experimental results show that the slice rms emittance of the electron bunch generated by photocathode RF gun has considerable variations along the bunch and is typically less than 0.55 mm mrad for the laser rms radius of 0.4 mm.

  11. Invariant electro-optical system for deflection measurement of floating docks

    Science.gov (United States)

    Gorbachev, Alexey A.; Hoang, Anh Phuong

    2017-06-01

    An electro-optical system for deflection measurement of floating docks is represented in this paper. This system contains a base unit with two measurement channels observing opposite directions of the dock. It also includes a set of reference marks and an industrial computer. The measurement unit contains of a camera with long focal-length lens and a beam splitter. The effect of the beam splitter turning point on the image position of the reference mark on the camera is analyzed as well in this paper.

  12. Electron Spectroscopy

    Science.gov (United States)

    Siegbahn, Kai

    Wilhelm Conrad Röntgen's discovery of X radiation in 1895 in Wörzburg resulted in an immediate break-through not only in physics but also in Society, the latter mainly because of its sensational radiological applications. Within a short time it furthermore indirectly led to the discovery of radioactivity by Henri Becquerel. The discovery of X radiation opened the gate to modern atomic physics, and radioactivity to nuclear physics. Later on, the discovery of X-ray diffraction by Laue, Friedrich and Knipping in 1912 initiated the field of X-ray spectroscopy with its fundamental contributions to atomic and crystal structures. Secondary electrons were early observed in the scattered radiation when X-rays were hitting a sample. The development of the corresponding electron spectroscopy had to wait a much longer time for its maturity. A survey of electron spectroscopy is presented.

  13. The role of Ca2+ in deflection-induced excitation of motile, mechanoresponsive balancer cilia in the ctenophore statocyst.

    Science.gov (United States)

    Lowe, B

    1997-06-01

    Motile, mechanoresponsive cilia (balancers) in ctenophore statocysts, like vertebrate hair cells, are excited or inhibited depending upon the direction in which they are deflected. Balancers, however, may become either excited (beat rapidly) or inhibited (beat slowly) by deflection in the same direction, depending on the sign of ctenophore geotaxis (positive or negative). The beat frequency of many cilia is controlled by concentrations of Ca2+, membrane potential and neural input. How these factors affect deflection-induced ciliary beating in balancers was investigated. Deflection-induced excitation of balancers in whole Mnemiopsis leidyi larvae and dissected adult (Mnemiopsis leidyi, Pleurobrachia pileus) statocysts was reversibly inhibited by the Ca2+ channel inhibitors Co2+, Mg2+, Ni2+, and Mn2+. Deflection-induced excitation in balancers of isolated adult M. leidyi balancer groups was also inhibited by Co2+ or by Ca(2+)-free medium. Isolated balancer group cilia, like balancer cilia of intact ctenophores, exhibited responses to either sign of geotaxis and graded responses to deflection. Isolated balancers that were chemically depolarized in high-[K+], Ca(2+)-free medium were excited by local application of Ca2+ onto the ciliary bases, but not onto the cell bases or the ciliary tips. It is proposed that deflection-induced excitation of balancers is due to influx of Ca2+ through stretch- and voltage-activated channel activity. The sign of geotaxis of whole larvae and dissected adult statocysts was switched by electrical stimulation. Thus, neural input may participate in reversing the directional sensitivity of balancer cells.

  14. Measurement of ultra-low ion energy of decelerated ion beam using a deflecting electric field

    Energy Technology Data Exchange (ETDEWEB)

    Thopan, P.; Suwannakachorn, D.; Tippawan, U. [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Yu, L.D., E-mail: yuld@thep-center.org [Plasma and Beam Physics Research Facility, Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thailand Center of Excellence in Physics, Commission on Higher Education, 328 Si Ayutthaya Road, Bangkok 10400 (Thailand)

    2015-12-15

    In investigation on ultra-low-energy ion bombardment effect on DNA, an ion beam deceleration lens was developed for high-quality ultra-low-energy ion beam. Measurement of the ion energy after deceleration was necessary to confirm the ion beam really decelerated as theoretically predicted. In contrast to conventional methods, this work used a simple deflecting electrostatic field after the deceleration lens to bend the ion beam. The beam bending distance depended on the ion energy and was described and simulated. A system for the measurement of the ion beam energy was constructed. It consisted of a pair of parallel electrode plates to generate the deflecting electrical field, a copper rod measurement piece to detect ion beam current, a vernier caliper to mark the beam position, a stepping motor to translate the measurement rod, and a webcam-camera to read the beam bending distance. The entire system was installed after the ion-beam deceleration lens inside the large chamber of the bioengineering vertical ion beam line. Moving the measurement rod across the decelerated ion beam enabled to obtain beam profiles, from which the beam bending distance could be known and the ion beam energy could be calculated. The measurement results were in good agreement with theoretical and simulated results.

  15. The Multichannel Deflection Plates Control System for the ALF Facility at the APS

    CERN Document Server

    Deriy, Boris

    2005-01-01

    A deflection plate control system was developed as part of SPIRIT (Single Photon Ionization / Resonant Ionization to Threshold), a new secondary neutral mass spectrometry (SNMS) instrument that uses tunable vacuum ultraviolet light from the ALF (Argonne Linear Free-electron laser) facility at the APS for postionization. The system comprises a crate controller with PC104 embedded computer, 32 amplifiers, and two 1-kV power supplies. Thirty-two D/A converters are used to control voltages at the deflection plates within ± 400 V with 100-mV resolution. An algorithm of simultaneous sweeping of up to 16 XY areas with 10-μs time resolution also has been implemented in the embedded computer. The purpose of the system is to supply potentials to various ion optical elements for electrostatic control of keV primary and secondary ion beams in this SNMS instrument. The control system is of particular value in supplying (1) bipolar potentials for steering ions, (2) multiple potentials for octupole lenses...

  16. Coherent control of double deflected anomalous modes in ultrathin trapezoid-shaped slit metasurface

    Science.gov (United States)

    Zhu, Z.; Liu, H.; Wang, D.; Li, Y. X.; Guan, C. Y.; Zhang, H.; Shi, J. H.

    2016-11-01

    Coherent light-matter interaction in ultrathin metamaterials has been demonstrated to dynamically modulate intensity, polarization and propagation direction of light. The gradient metasurface with a transverse phase variation usually exhibits an anomalous refracted beam of light dictated by so-called generalized Snell’s law. However, less attention has been paid to coherent control of the metasurface with multiple anomalous refracted beams. Here we propose an ultrathin gradient metasurface with single trapezoid-shaped slot antenna as its building block that allows one normal and two deflected transmitted beams. It is numerically demonstrated that such metasurface with multiple scattering modes can be coherently controlled to modulate output intensities by changing the relative phase difference between two counterpropagating coherent beams. Each mode can be coherently switched on/off and two deflected anomalous beams can be synchronously dictated by the phase difference. The coherent control effect in the trapezoid-shaped slit metasurface will offer a promising opportunity for multichannel signals modulation, multichannel sensing and wave front shaping.

  17. Linear Analytical Solutions of Mechanical Sensitivity in Large Deflection of Unsymmetrically Layered Piezoelectric Plate under Pretension

    Directory of Open Access Journals (Sweden)

    Chun-Fu Chen

    2014-03-01

    Full Text Available Linear analytical study on the mechanical sensitivity in large deflection of unsymmetrically layered and laterally loaded piezoelectric plate under pretension is conducted. von Karman plate theory for large deflection is utilized but extended to the case of an unsymmetrically layered plate embedded with a piezoelectric layer. The governing equations thus obtained are simplified by omitting the arising nonlinear terms, yielding a Bessel or modified Bessel equation for the lateral slope. Depending on the relative magnitude of the piezoelectric effect, for both cases, analytical solutions of various geometrical responses are developed and formulated via Bessel and modified Bessel functions. The associated ultimate radial stresses are further derived following lamina constitutive law to evaluate the mechanical sensitivity of the considered plate. For a nearly monolithic plate under a very low applied voltage, the results are in good agreement with those for a single-layered case due to pure mechanical load available in literature, and thus the present approach is checked. For a two-layered unsymmetric plate made of typical silicon-based materials, a sound piezoelectric effect is illustrated particularly in a low pretension condition.

  18. Thermal deflection analysis of the solidified shell in continuous casting of slab

    Institute of Scientific and Technical Information of China (English)

    LIU Hongzhao; WANG Zhongmin

    2007-01-01

    The thermal deformation problem in the continuous casting of a slab subjected to thermal loading because of the temperature gradient along the solidified shell thickness is investigated.On the basis of the reciprocal theorem of work or Betti-MaxweU's reciprocal theorem and the superposition principle,the deflection expressions for a rectangular plate with the two opposite edges simply supported,and the other two opposite edges clamped under the action of the uniformly distributed load and nonuniform temperature field are derived respectively.The meaning of each term in the deflection expression obtained by the reciprocal theorem of work is explained.Then the practical example is given to calculate the thermal deformation and the bulging deformation of the solidified shell under three tension speeds.This research is useful for analyzing the bulging deformation in the continuous casting of a slab under the static pressure of the molten steel and the thermal loading because of the temperature gradient along the solidified shell thickness.

  19. Discourses of Deflection: The Politics of Framing China’s South-North Water Transfer Project

    Directory of Open Access Journals (Sweden)

    Britt Crow-Miller

    2015-06-01

    Full Text Available Despite significant financial, ecological and social trade-offs, China has moved forward with constructing and operationalising the world’s largest interbasin water transfer project to date, the South-North Water Transfer Project (SNWTP. While it is fundamentally linked to broader political-economic goals within the context of China’s post-Mao development agenda, the SNWTP is frequently discussed in apolitical terms. Based on extensive discourse analysis and interviews with government officials across North China, I argue that the Chinese government is using "discourses of deflection" to present the project as politically neutral in order to serve its ultimate goal of maintaining the high economic growth rates that underpin its continued legitimacy. These discourses, which replace concerns with human-exacerbated water stress with naturalised narratives about water scarcity and the ecological benefits of water transfer, serve to deflect attention away from anthropogenic sources of water stress in the North China Plain and serve as apolitical justifications for pursuing a short-term supply-side approach rather than the more politically challenging and longer-term course of dealing with the underlying drivers of water stress in the region.

  20. Detection without deflection? A hypothesis for direct sensing of sound pressure by hair cells

    Indian Academy of Sciences (India)

    Andrew Bell

    2007-03-01

    It is widely thought that organisms detect sound by sensing the deflection of hair-like projections, the stereocilia, at the apex of hair cells. In the case of mammals, the standard interpretation is that hair cells in the cochlea respond to deflection of stereocilia induced by motion generated by a hydrodynamic travelling wave. But in the light of persistent anomalies, an alternative hypothesis seems to have some merit: that sensing cells (in particular the outer hair cells) may, at least at low intensities, be reacting to a different stimulus – the rapid pressure wave that sweeps through the cochlear fluids at the speed of sound in water. This would explain why fast responses are sometimes seen before the peak of the travelling wave. Yet how could cells directly sense fluid pressure? Here, a model is constructed of the outer hair cell as a pressure vessel able to sense pressure variations across its cuticular pore, and this ‘fontanelle’ model, based on the sensing action of the basal body at this compliant spot, could explain the observed anomalies. Moreover, the fontanelle model can be applied to a wide range of other organisms, suggesting that direct pressure detection is a general mode of sensing complementary to stereociliar displacement.

  1. Small-body deflection techniques using spacecraft: techniques in simulating the fate of ejecta

    CERN Document Server

    Schwartz, Stephen R; Michel, Patrick; Jutzi, Martin

    2016-01-01

    We define a set of procedures to numerically study the fate of ejecta produced by the impact of an artificial projectile with the aim of deflecting an asteroid. Here we develop a simplified, idealized model of impact conditions that can be adapted to fit the details of specific deflection-test scenarios, such as what is being proposed for the AIDA project. Ongoing studies based upon the methodology described here can be used to inform observational strategies and safety conditions for an observing spacecraft. To account for ejecta evolution, the numerical strategies we are employing are varied and include a large N-Body component, a smoothed-particle hydrodynamics (SPH) component, and an application of impactor scaling laws. Simulations that use SPH-derived initial conditions show high-speed ejecta escaping at low angles of inclination, and very slowly moving ejecta lofting off the surface at higher inclination angles, some of which re-impacts the small-body surface. We are currently investigating the realism...

  2. Measurement of ultra-low ion energy of decelerated ion beam using a deflecting electric field

    Science.gov (United States)

    Thopan, P.; Suwannakachorn, D.; Tippawan, U.; Yu, L. D.

    2015-12-01

    In investigation on ultra-low-energy ion bombardment effect on DNA, an ion beam deceleration lens was developed for high-quality ultra-low-energy ion beam. Measurement of the ion energy after deceleration was necessary to confirm the ion beam really decelerated as theoretically predicted. In contrast to conventional methods, this work used a simple deflecting electrostatic field after the deceleration lens to bend the ion beam. The beam bending distance depended on the ion energy and was described and simulated. A system for the measurement of the ion beam energy was constructed. It consisted of a pair of parallel electrode plates to generate the deflecting electrical field, a copper rod measurement piece to detect ion beam current, a vernier caliper to mark the beam position, a stepping motor to translate the measurement rod, and a webcam-camera to read the beam bending distance. The entire system was installed after the ion-beam deceleration lens inside the large chamber of the bioengineering vertical ion beam line. Moving the measurement rod across the decelerated ion beam enabled to obtain beam profiles, from which the beam bending distance could be known and the ion beam energy could be calculated. The measurement results were in good agreement with theoretical and simulated results.

  3. ESTIMATION OF VERTICAL DEFLECTIONS IN CONCRETE BEAMS THROUGH DIGITAL CLOSE RANGE PHOTOGRAMMETRY

    Directory of Open Access Journals (Sweden)

    I. Detchev

    2012-09-01

    Full Text Available Deformation monitoring, and in general structural health monitoring, of civil infrastructure systems is important in terms of both safety and serviceability. Traditionally, large structures have been monitored using surveying techniques, while fine-scale monitoring of structural components has been done with geotechnical instrumentation. This paper reviews the advantages and disadvantages of using remote sensing methods, such as terrestrial laser scanning and digital close range photogrammetry, for the purposes of precise 3D reconstruction and the estimation of deflections in structural materials. It is also shown how a low-cost setup of multiple digital cameras and projectors can be used for the monitoring of concrete beams subjected to different loading conditions by a hydraulic actuator. The photogrammetric system used does not require any physical targets other than for the purposes of establishing the relative orientation between the involved cameras. The setup was tested in two experiments, and the beam deflections resulted from the photogrammetric system were compared to the ones from a set of one-dimensional laser transducers and a terrestrial laser scanner. The experiments proved that it was possible to detect sub-millimetre level deformations given the used equipment and the geometry of the setup.

  4. An improved small-deflection electromechanical model for piezoelectric bending beam actuators and energy harvesters

    Science.gov (United States)

    Tabesh, Ahmadreza; Fréchette, Luc G.

    2008-10-01

    The analytical model presented in this paper describes the energy conversion mechanism of a piezoelectric beam (bimorph) under small-deflection static and vibrating conditions. The model provides an improved approach to design and analyze the performance of piezoelectric actuators and energy harvesters (sensors). Conventional models assume a linear voltage distribution over the piezoelectric beam thickness, which is shown here to be invalid. The proposed modeling method improves accuracy by using a quadratic voltage distribution. The equivalent capacitance of a beam shows a 40% discrepancy between a conventional model and the proposed model for PZT5A material. This inaccuracy level is not negligible, especially when the design of micro-power electrical energy harvesting is concerned. The method solves simultaneously the solid mechanics and Maxwell's equations with the constitutive equations for piezoelectric materials. The paper also proposes a phasor-based procedure for measuring the damping of a piezoelectric beam. An experimental setup is developed to verify the validity of the model. The experimental results confirm the accuracy of the improved model and also reveal limitations in using models for small deflections.

  5. Transient deflection response in microcantilever array integrated with polydimethylsiloxane (PDMS) microfluidics.

    Science.gov (United States)

    Anderson, Ryan R; Hu, Weisheng; Noh, Jong Wook; Dahlquist, William C; Ness, Stanley J; Gustafson, Timothy M; Richards, Danny C; Kim, Seunghyun; Mazzeo, Brian A; Woolley, Adam T; Nordin, Gregory P

    2011-06-21

    We report the integration of a nanomechanical sensor consisting of 16 silicon microcantilevers with polydimethylsiloxane (PDMS) microfluidics. For microcantilevers positioned near the bottom of a microfluidic flow channel, a transient differential analyte concentration for the top versus bottom surface of each microcantilever is created when an analyte-bearing fluid is introduced into the flow channel (which is initially filled with a non-analyte containing solution). We use this effect to characterize a bare (nonfunctionalized) microcantilever array in which the microcantilevers are simultaneously read out with our recently developed high sensitivity in-plane photonic transduction method. We first examine the case of non-specific binding of bovine serum albumin (BSA) to silicon. The average maximum transient microcantilever deflection in the array is -1.6 nm, which corresponds to a differential surface stress of only -0.23 mN m(-1). This is in excellent agreement with the maximum differential surface stress calculated based on a modified rate equation in conjunction with finite element simulation. Following BSA adsorption, buffer solutions with different pH are introduced to further study microcantilever array transient response. Deflections of 20-100 nm are observed (2-14 mN m(-1) differential surface stress). At a flow rate of 5 μL min(-1), the average measured temporal width (FWHM) of the transient response is 5.3 s for BSA non-specific binding and 0.74 s for pH changes.

  6. Realization of Deflection-type Bridge instruments to determine soil moisture using Research-Based Learning

    Science.gov (United States)

    Yuliza, E.; Munir, M. M.; Abdullah, M.; Khairurrijal

    2016-08-01

    It is clear that the quality of education is directly related to the quality of teachers and the teaching methods. One of the teaching methods that can improve the quality of education is research-based learning (RBL) method. In this method, students act as the center of learning while teachers become the guides that provide direction and advice. RBL is a learning method that combines cooperative learning, problem solving, authentic learning, contextual case study and inquiry approach discovery. The main goal of this method is to construct a student that can think critically, analyze and evaluate problems, and find a new science from these problems (learning by doing). In this paper, RBL is used to improve the understanding about measurement using deflection-type Bridge that is implemented in the determination of ground water changes. In general, there are three stages that have been done. Firstly the exposure stage, then the experience stage and lastly the capstone stage. The exposure stage aims to increase the knowledge and the comprehension of student about the topic through understanding the basics concepts, reviewing the literature and others. The understanding gained in the exposure stage is being used for application and analysis at the experience stage. While the final stage is the publication of research results both verbally and in writing. Based on the steps that have been conducted, it can be showed that deflection-type Bridge can be utilized in soil moisture meter.

  7. Beam steering and deflecting device using step-based micro-blazed grating

    Science.gov (United States)

    Yang, Junbo; Su, Xianyu; Xu, Ping; Gu, Zheng

    2008-08-01

    The rapidly evolving demands of optical communications and optical switching systems have created a new market for high capacity all-optical beam steering and deflecting techniques. One technology potentially capable of realizing such systems uses the multistep micro-blazed grating optical beam deflectors based on binary and multiple-phase modulation methods. The micro-optical element has been fabricated by introducing very large scale integration (VLSI), stepping photolithography and reactive ion etching (RIE), which can realize beam steering, deflecting, splitting, and switching in free space, and its diffraction properties are determined by the blazed-grating parameters, such as the number of steps, grating depth, grating period, as well as blazed profile. The theoretical analysis and primarily experimental result show that this phase-type element has the advantages of high diffractive efficiency, low cross talk, small feature size, and high reliability due to nonmechanical beam steering without any moving parts. Hence it is ideally suited to applications in optical communication and optical interconnection network.

  8. A model to predict deflection of bevel-tipped active needle advancing in soft tissue.

    Science.gov (United States)

    Datla, Naresh V; Konh, Bardia; Honarvar, Mohammad; Podder, Tarun K; Dicker, Adam P; Yu, Yan; Hutapea, Parsaoran

    2014-03-01

    Active needles are recently being developed to improve steerability and placement accuracy for various medical applications. These active needles can bend during insertion by actuators attached to their bodies. The bending of active needles enables them to be steered away from the critical organs on the way to target and accurately reach target locations previously unachievable with conventional rigid needles. These active needles combined with an asymmetric bevel-tip can further improve their steerability. To optimize the design and to develop accurate path planning and control algorithms, there is a need to develop a tissue-needle interaction model. This work presents an energy-based model that predicts needle deflection of active bevel-tipped needles when inserted into the tissue. This current model was based on an existing energy-based model for bevel-tipped needles, to which work of actuation was included in calculating the system energy. The developed model was validated with needle insertion experiments with a phantom material. The model predicts needle deflection reasonably for higher diameter needles (11.6% error), whereas largest error was observed for the smallest needle diameter (24.7% error).

  9. ABRUPT DEFLECTED SUPERCRITICAL WATER FLOW-REVISED THEORY OF SHOCK WAVE

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The shock wave angle and depth ratio of the abrupt deflected supercritical water flow due to deflector was investigated experimentally and theoretically. A correction coefficient of the hydro-dynamic pressure ξ was introduced to generalize the momentum equation in the perpendicular direction to the shock front. An extensive series of tests were conducted in a 1 m wide flume with the Froude number ranging from 1.70 to 8.37, the deflection angle ranging from 5° to 40° and the length of deflector ranging from 0.28 m to 1 m. A dimensionless parameter K was defined to depict the ratio of the flow height to flow thickness. Test results show that the value of ξ, the correction coefficient of the non-hydrostatic pressure distribution, decreases with the increase of the value of K. An empirical relationship between the value of ξ and the value of K was proposed. It is indicated that the relative errors of the results calculated by the revised theory is much smaller than that obtained from the Ippen theory. Finally, a simple explicit expression was suggested to calculate the shock wave height ratio in consideration of the effect of the non-hydrostatic pressure distribution.

  10. Challenges of deflecting an asteroid or cometary nucleus with a nuclear burst

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, Paul A [Los Alamos National Laboratory; Plesko, Cathy S [Los Alamos National Laboratory; Clement, Ryan R C [Los Alamos National Laboratory; Conlon, Leann M [Los Alamos National Laboratory; Weaver, Robert P [Los Alamos National Laboratory; Guzik, Joyce A [Los Alamos National Laboratory; Pritchett - Sheets, Lori A [Los Alamos National Laboratory; Huebner, Walter F [SOUTHWEST RESEARCH INSTITUTE

    2009-01-01

    There are many natural disasters that humanity has to deal with over time. These include earthquakes, tsunami, hurricanes, floods, asteroid strikes, and so on. Many of these disasters occur slowly enough that some advance warning of which areas will be affected is possible. However, in almost all cases, the response is to evacuate the area to be affected and deal with the damage later. The evacuations for hurricanes Katrina and Rita on the US Gulf Coast in 2005 demonstrated the chaos that can result. In contrast with other natural disasters. it is likely that an asteroid or cometary nucleus on a collision course with Earth is likely to be detected with enough warning time to possibly deflect it away from the collision course. Thanks to near-Earth object (NEO) surveys, people are working towards a goal of cataloging at least 90% of all near-Earth objects with diameters larger than {approx}140 meters in the next decade. The question is how to mitigate the threat from an asteroid or cometary nucleus found to be on a collision course. We briefly review some possible methods, describing their good and bad points, and then embark on a more detailed description of using a nuclear munition in standoff mode to deflect an asteroid or cometary nucleus before it can hit Earth.

  11. Heart rate deflection point relates to second ventilatory threshold in a tennis test.

    Science.gov (United States)

    Baiget, Ernest; Fernández-Fernández, Jaime; Iglesias, Xavier; Rodríguez, Ferran A

    2015-03-01

    The relationship between heart rate deflection point (HRDP) and the second ventilatory threshold (VT2) has been studied in continuous sports, but never in a tennis-specific test. The aim of the study was to assess the relationships between HRDP and the VT2, and between the maximal test performance and the maximal oxygen uptake ((Equation is included in full-text article.)) in an on-court specific endurance tennis test. Thirty-five high-level tennis players performed a progressive tennis-specific field test to exhaustion to determine HRDP, VT2, and (Equation is included in full-text article.). Ventilatory gas exchange parameters were continuously recorded by a portable telemetric breath-by-breath gas exchange measurement system. Heart rate deflection point was identified at the point at which the slope values of the linear portion of the time/heart rate (HR) relationship began to decline and was successfully determined in 91.4% of the players. High correlations (r = 0.79-0.96; p tennis test can be used to determine the VT2, and the BallfHRDP can be used as a practical performance variable to prescribe on-court specific aerobic training at or near VT2.

  12. The vacuole model: new terms in the second order deflection of light

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharya, Amrita; Nandi, Kamal K. [Department of Mathematics, University of North Bengal, Raja Rammohunpur, Siliguri 734 013 (India); Garipova, Guzel M. [Department of Theoretical Physics, Sterlitamak State Pedagogical Academy, 49, Lenin Street, Sterlitamak 453103 (Russian Federation); Laserra, Ettore [DMI, Università di Salerno, Via Ponte Don Melillo, 84084 Fisciano, Salerno (Italy); Bhadra, Arunava, E-mail: amrita852003@yahoo.co.in, E-mail: goldberg144@gmail.com, E-mail: elaserra@unisa.it, E-mail: aru_bhadra@yahoo.com, E-mail: kamalnandi1952@yahoo.co.in [High Energy and Cosmic Ray Research Center, University of North Bengal, Raja Rammohunpur, Siliguri 734 013 (India)

    2011-02-01

    The present paper is an extension of a recent work (Bhattacharya et al. 2010) to the Einstein-Strauss vacuole model with a cosmological constant, where we work out the light deflection by considering perturbations up to order M{sup 3} and confirm the light bending obtained previously in their vacuole model by Ishak et al. (2008). We also obtain another local coupling term −5πM{sup 2}Λ/8 related to Λ, in addition to the one obtained by Sereno (2008, 2009). We argue that the vacuole method for light deflection is exclusively suited to cases where the cosmological constant Λ disappears from the path equation. However, the original Rindler-Ishak method (2007) still applies even if a certain parameter γ of Weyl gravity does not disappear. Here, using an alternative prescription, we obtain the known term −γR/2, as well as another new local term 3πγM/2 between M and γ. Physical implications are compared, where we argue that the repulsive term −γR/2 can be masked by the Schwarzschild term 2M/R in the halo regime supporting attractive property of the dark matter.

  13. Utilization of an H-reversal trajectory of a solar sail for asteroid deflection

    Institute of Scientific and Technical Information of China (English)

    Sheng-Ping Gong; Jun-Feng Li; Xiang-Yuan Zeng

    2011-01-01

    Near Earth Asteroids have a possibility of impacting the Earth and always represent a threat.This paper proposes a way of changing the orbit of the asteroid to avoid an impact.A solar sail evolving in an H-reversal trajectory is utilized for asteroid deflection.Firstly,the dynamics of the solar sail and the characteristics of the H-reversal trajectory are analyzed.Then,the attitude of the solar sail is optimized to guide the sail to impact the target asteroid along an H-reversal trajectory.The impact velocity depends on two important parameters:the minimum solar distance along the trajectory and lightness number of the solar sail.A larger lightness number and a smaller solar distance lead to a higher impact velocity.Finally,the deflection capability of a solar sail impacting the asteroid along the H-reversal trajectory is discussed.The results show that a 10 kg solar sail with a lead-time of one year can move Apophis out of a 600-m keyhole area in 2029 to eliminate the possibility of its resonant return in 2036.

  14. Development of Deflection Prediction Model for Concrete Block Pavement Considering the Block Shapes and Construction Patterns

    Directory of Open Access Journals (Sweden)

    Wuguang Lin

    2016-01-01

    Full Text Available Concrete block pavement (CBP is distinct from typical concrete or asphalt pavements. It is built by using individual blocks with unique construction patterns forming a discrete surface layer to bear traffic loadings. The surface structure of CBP varies depending on the block shapes and construction patterns, so it is hard to apply a general equivalent elastic modulus estimation method to define the surface structural strength. In this study, FEM analysis and dynamic loading test were carried out to develop a deflection prediction model for CBP considering the block shapes and construction patterns. Based on the analysis results, it was found that block shapes did not have much effect on load distribution, whereas construction patterns did. By applying the deflection prediction model to the rutting model for CBP proposed by Sun, the herringbone bond pattern showed the best performance comparing with stretcher bond or basket weave bond pattern. As the load repetition increased to 1.2 million, the rutting depth of CBP constructed by herringbone bond pattern was 2 mm smaller than those constructed by the other two patterns.

  15. Effects of varying the through silicon via liners thickness on their hoop stresses and deflections

    Directory of Open Access Journals (Sweden)

    Juma Mary Atieno

    2017-03-01

    Full Text Available Through silicon via (TSV interconnect reliability is a problem in electronic packaging. The authors address the insertion losses, deflections which can result to separation of TSV layers and hoop stresses. These problems are due to different coefficient of thermal expansion between materials. The authors propose a robust methodology for (TSV liners in this paper which in turn solves the reliability problem in (TSV. Silicon dioxide material is used in their paper as a TSV liner. First, they modelled the equivalent TSV circuit in advanced design systems (ADS. The authors then simulated it to obtain the TSV characterisation from which they obtained the S-parameter S21 which represents the insertion losses. Insertion losses have been described with changes in frequencies from 0 to 20 GHz with changes in TSV thickness from 7 to 8 µm. Later two different shapes of the TSV liner; the disc- and rod-shaped are modelled in analysis system 14 software. The two shapes with a radius of 5 µm each and a fixed pressure of 100 µPa developed changes in hoop stresses and deflections when the liners thicknesses are varied from 2 to 3 µm. The disc shape experienced least reliability problems so the authors propose its use in via structures.

  16. Experimental and theoretical analysis of DEP-based particle deflection for the separation of protein-bound particles

    Science.gov (United States)

    Kim, Min-Soo; Kim, Jong-Ho; Lee, Yoon-Sik; Lim, Geon-Gyu; Lee, Hyang-Beom; Park, Jae-Hyoung; Kim, Yong-Kweon

    2009-01-01

    We present an experimental and theoretical analysis of dielectrophoretic (DEP) particle deflection in a microfluidic channel for the separation of protein-bound particles. A 2D electrode array with widely spaced bars is designed to deflect a particle at the exit of the fluidic channel by negative DEP force. When particles pass through the channel, the particle streams are deflected differently depending on the DEP characteristics of the particles. In this paper, we propose methodologies to characterize the DEP force with the deflection distance using comparative analyses of a simulation and an experiment. The deflection distances of the particles are measured as a function of the ac voltage applied and compared with full 3D simulations. The Clausius-Mossotti (CM) factor of a protein-bound particle is analyzed, based on frequency-dependent deflection distance data measured experimentally, and protein-bound particles are separated from a mixture with nonbound particles in a real application. Two particle groups, 2.3 µm and 6.4 µm polystyrene particles, were used for the simulation and experimental study, and the 6.4 µm diameter particles were selected as an adequate protein-binding substrate for the application of biomolecular detection. Bovine serum albumin (BSA) was used as a test target protein. The particle's BSA binding is identified by the change in the particle's deflection distance. In particular, we used 1 wt% BSA as a target protein sample to investigate the deflection of 6.4 µm diameter particles as a function of protein concentration. The frequency-dependent CM factor curves for BSA-bound and nonbound particles are also calculated theoretically. Therefore, this paper shows a model analytic study on the biomolecular detection performance of a fabricated DEP-deflection microsystem. In addition, we present further significant analyses such as calculation of the electrical surface conductance of BSA around a particle, and we trace simulation errors. The

  17. Raman spectroscopy

    Science.gov (United States)

    Raman spectroscopy has gained increased use and importance in recent years for accurate and precise detection of physical and chemical properties of food materials, due to the greater specificity and sensitivity of Raman techniques over other analytical techniques. This book chapter presents Raman s...

  18. Modern Spectroscopy

    Science.gov (United States)

    Barrow, Gordon M.

    1970-01-01

    Presents the basic ideas of modern spectroscopy. Both the angular momenta and wave-nature approaches to the determination of energy level patterns for atomic and molecular systems are discussed. The interpretation of spectra, based on atomic and molecular models, is considered. (LC)

  19. A simple analytical solution for predicting deflection of a hybrid FRP-aluminum modular space truss bridge

    Institute of Scientific and Technical Information of China (English)

    李飞; 张冬冬; 赵启林; 邓安仲

    2015-01-01

    A novel hybrid FRP-aluminum space truss was employed in a two-rut modular bridge superstructure, which is composed of standard structural units. The main objective of this work was to obtain a simple analytical solution that can conveniently predict the deflection of the proposed hybrid space truss bridge. The analytical formulae are expected to possess a straightforward format and simple calculation process. A simple description of the proposed bridge was introduced. The design formulae of the deflection were derived based on a simplified analytical plane truss model, which possessed hinge nodes and was subsequently simplified as two solid web beams during the theoretical derivation process. To validate the analytical model and formulae, numerical and experimental works were conducted and compared with the theoretical solutions. The results indicate that the analytical formulae provide higher deflection magnitudes with a difference of <1.5% compared with the experiments performed and <4.5% compared with the FE model used; the simplified plane truss is thus shown to be an effective analytical model for the derivation of deflection design formulae, which can conveniently calculate the deflection of the hybrid space truss bridge with satisfactory accuracy.

  20. Analytical and Numerical Deflection Study on the Structure of 10 kW Low Speed Permanent Magnet Generator

    Directory of Open Access Journals (Sweden)

    Hilman Syaeful Alam

    2012-12-01

    Full Text Available Analytical and numerical studies of the deflection in the structure of 10 kW low speed permanent magnet generator (PMG have been discussed in this paper. This study is intended to prevent failure of the structure when the prototype is made. Numerical analysis was performed with the finite-element method (FEM. Flux density, weight and temperature of the components are the required input parameters. Deflection observed were the movements of the two main rotor components, namely the rim and shaft, where the maximum deflection allowed at the air gap between rotor and stator should be between 10% to 20% of the air gap clearance or 0.1000 mm to 0.2000 mm. Base on the analysis, total deflection of the analytic calculation was 0.0553 mm, and numerical simulation was 0.0314 mm. Both values were in the acceptable level because it was still below the maximum allowed deflection. These results indicate that the structure of a permanent magnet generator (rim and shaft can be used safely.

  1. The effect of fluoride exposure on the load-deflection properties of superelastic nickel-titanium-based orthodontic archwires.

    Science.gov (United States)

    Ahrari, Farzaneh; Ramazanzadeh, Barat-Ali; Sabzevari, Berahman; Ahrari, Ali

    2012-05-01

    It has been demonstrated that fluoride prophylactic agents may cause hydrogen absorption in NiTi wires and degrade their mechanical properties. To investigate the effect of a fluoride mouthwash on load-deflection characteristics of three types of nickel-titanium-based orthodontic archwires. Twenty maxillary 0.016 inch round specimens from each of the single-strand NiTi (Rematitan 'Lite'), multi-strand NiTi (SPEED Supercable) and Copper NiTi (Damon Copper NiTi) wires were selected. The specimens were kept in either 0.2% NaF or artificial saliva solutions at 37 degrees C for 24 hours (N = 10). The wire load-deflection properties were measured by a Zwick testing machine, using a three-point bending test. An un-paired student's t-test, a one-way ANOVA and a Tukey post-hoc test were used to assess statistical significance. Immersion in NaF solution affected the load-deflection properties of NiTi wires. The unloading forces at 0.5 and 1.0 mm deflections were significantly lower in fluoride-treated specimens compared with the control groups (p fluoride- and saliva-treated specimens (p > 0.05). The results suggested that subjecting NiTi wires to fluoride agents decreased associated unloading forces, especially at lower deflections, and may result in delayed tooth alignment.

  2. Evaluation of the force generated by gradual deflection of orthodontic wires in conventional metallic, esthetic, and self-ligating brackets

    Directory of Open Access Journals (Sweden)

    Manoela Fávaro Francisconi

    Full Text Available ABSTRACT Objective: The purpose of this study was to evaluate the deflection forces of Nitinol orthodontic wires placed in different types of brackets: metallic, reinforced polycarbonate with metallic slots, sapphire, passive and active self-ligating, by assessing strength values variation according to gradual increase in wire diameter and deflection and comparing different combinations in the different deflections. Material and Methods: Specimens were set in a clinical simulation model and evaluated in a Universal Testing Machine (INSTRON 3342, using the ISO 15841 protocol. Data were subjected to One-way ANOVA, followed by Tukey tests (p<0.05. Results: Self-ligating brackets presented the most similar behavior to each other. For conventional brackets there was no consistent behavior for any of the deflections studied. Conclusions: Self-ligating brackets presented the most consistent and predictable results while conventional brackets, as esthetic brackets, showed very different patterns of forces. Self-ligating brackets showed higher strength in all deflections when compared with the others, in 0.020-inch wires.

  3. Deflecting RF cavity design for a recirculating linac based facility for ultrafast X-ray science (LUX)

    Energy Technology Data Exchange (ETDEWEB)

    Li, Derun; Corlett, J.N.

    2003-05-01

    We report on superconducting deflecting RF cavity designs for a Recirculating Linac Based Facility for Ultrafast X-ray Science (LUX) at Lawrence Berkeley National Laboratory. The deflecting cavities operate in the lowest dipole mode and are required to produce a temporal correlation within flat electron bunches, as needed for x-ray compression in crystal optics. Deflecting voltage of up to 8.5-MV is required at 3.9-GHz. We present a 7-cell cavity design in this paper. Seven such cavities are required to generate the 8.5 MV deflecting voltage. Longitudinal and transverse impedance from LOM (lower order mode) and HOM (higher order mode) are simulated using the MAFIA code. Short-range and long-range wakefield excited through these impedances are calculated. Beam loading effects of the deflecting mode and LOM modes are estimated. Q values of the LOM monopole modes in the cavity may need to be damped to be below 10{sup 4}-10{sup 5} levels in order to maintain the required energy spread.

  4. Deflection of high energy protons by multiple volume reflections in a modified multi-strip silicon deflector

    CERN Document Server

    Scandale, W; Butcher, M.; Cerutti, F.; Gilardoni, S.; Lari, L.; Lechner, A.; Losito, R.; Masi, A.; Mereghetti, A.; Metral, E.; Mirarchi, D.; Montesano, S.; Redaelli, S.; Schoofs, P.; Smirnov, G.; Bagli, E.; Bandiera, L.; Baricordi, S.; Dalpiaz, P.; Guidi, V.; Mazzolari, A.; Vincenzi, D.; Claps, G.; Dabagov, S.; Hampai, D.; Murtas, F.; Cavoto, G.; Garattini, M.; Iacoangeli, F.; Ludovici, L.; Santacesaria, R.; Valente, P.; Galluccio, F.; Afonin, A.G.; Chesnokov, Yu.A.; Maisheev, V.A.; Sandomirskiy, Yu.E.; Yanovich, A.A.; Yazynin, I.A.; Kovalenko, A.D.; Taratin, A.M.; Gavrikov, Yu.A.; Ivanov, Yu.M.; Lapina, L.P.; Ferguson, W.; Fulcher, J.; Hall, G.; Pesaresi, M.; Raymond, M.; Previtali, V.

    2014-01-01

    The effect of multiple volume reflections in one crystal was observed in each of several bent silicon strips for 400 GeV/c protons. This considerably increased the particle deflections. Some particles were also deflected due to channeling in one of the subsequent strips. As a result, the incident beam was strongly spread because of opposite directions of the deflections. A modified multi-strip deflector produced by periodic grooves on the surface of a thick silicon plate was used for these measurements. This technique provides perfect mutual alignment between crystal strips. Such multi-strip deflector may be effective for collider beam halo collimation and a study is planned at the CERN SPS circulating beam.

  5. Transverse deflections of an elastic spherical shell as a function of transverse and tangential loads

    DEFF Research Database (Denmark)

    Niordson, Christian F.; Nielsen, S.B.

    2006-01-01

    of the transverse deflection is modified by in-plane tectonic forces originating e.g. at plate boundaries. However, geoscience applications of the coupling between transverse deflections and boundary conditions have been restricted to the one-dimensional thin-plate model. In this paper we extend the model......The thin elastic plate model (the Kirchhoff model) in one and two space dimensions has proved extremely useful in providing a simple model of transverse deflections of the Earths lithosphere as a function of transverse loads. For example, the foreland basin of a mountain range is explained...... by this model by the load of the orogen on the lithosphere, and the primary, asymmetric trough associated with inversion structures in the European plate are explained by the intra-lithospheric load of the inversion ridge. It is well-known from the one-dimensional version of the plate model that the amplitude...

  6. Influence of incoherent scattering on stochastic deflection of high-energy negative particle beams in bent crystals

    Energy Technology Data Exchange (ETDEWEB)

    Kirillin, I.V. [Akhiezer Institute for Theoretical Physics, National Science Center ' ' Kharkov Institute of Physics and Technology' ' , Kharkov (Ukraine); Shul' ga, N.F. [Akhiezer Institute for Theoretical Physics, National Science Center ' ' Kharkov Institute of Physics and Technology' ' , Kharkov (Ukraine); V.N. Karazin Kharkov National University, Kharkov (Ukraine); Bandiera, L. [INFN Sezione di Ferrara, Ferrara (Italy); Guidi, V.; Mazzolari, A. [INFN Sezione di Ferrara, Ferrara (Italy); Universita degli Studi di Ferrara, Dipartimento di Fisica e Scienze della Terra, Ferrara (Italy)

    2017-02-15

    An investigation on stochastic deflection of high-energy negatively charged particles in a bent crystal was carried out. On the basis of analytical calculation and numerical simulation it was shown that there is a maximum angle at which most of the beam is deflected. The existence of a maximum, which is taken in the correspondence of the optimal radius of curvature, is a novelty with respect to the case of positively charged particles, for which the deflection angle can be freely increased by increasing the crystal length. This difference has to be ascribed to the stronger contribution of incoherent scattering affecting the dynamics of negative particles that move closer to atomic nuclei and electrons. We therefore identified the ideal parameters for the exploitation of axial confinement for negatively charged particle beam manipulation in future high-energy accelerators, e.g., ILC or muon colliders. (orig.)

  7. First Observation of the Deflection of a 33 TeV Pb Ion Beam in a Bent Silicon Crystal

    Science.gov (United States)

    Elsener, K.; Biino, C.; Clement, M.; Doble, N.; Gatignon, L.; Grafstrom, P.; Mikkelsen, U.; Taratin, A.; Møller, S. P.; Uggerhøj, E.

    1997-05-01

    The deflection of an ultra-relativistic, fully stripped Pb(82+) ion beam in a bent silicon crystal has been observed for the first time. The ions were provided by the CERN-SPS in the H4 beam at a momentum of 400 GeV/c/Z. A 60 mm long silicon crystal, bent over 50 mm to give a 4 mrad deflection angle, was used in this experiment. The measured Pb ion deflection efficiencies are comparable to the ones obtained with protons at an equivalent ratio p/Z, and are found to be about 15% for a beam with a divergence of 50 microradians (FWHM). The interaction rate observed in a background counter is reduced by about the same 15% when the crystal is well aligned with the beam. This corroborates further the channeling model, which predicts that channeled ions are steered away from regions of high electron densities as well as from the nuclei in the crystal.

  8. Real-Time Deflection Monitoring for Milling of a Thin-Walled Workpiece by Using PVDF Thin-Film Sensors with a Cantilevered Beam as a Case Study

    Directory of Open Access Journals (Sweden)

    Ming Luo

    2016-09-01

    Full Text Available Thin-walled workpieces, such as aero-engine blisks and casings, are usually made of hard-to-cut materials. The wall thickness is very small and it is easy to deflect during milling process under dynamic cutting forces, leading to inaccurate workpiece dimensions and poor surface integrity. To understand the workpiece deflection behavior in a machining process, a new real-time nonintrusive method for deflection monitoring is presented, and a detailed analysis of workpiece deflection for different machining stages of the whole machining process is discussed. The thin-film polyvinylidene fluoride (PVDF sensor is attached to the non-machining surface of the workpiece to copy the deflection excited by the dynamic cutting force. The relationship between the input deflection and the output voltage of the monitoring system is calibrated by testing. Monitored workpiece deflection results show that the workpiece experiences obvious vibration during the cutter entering the workpiece stage, and vibration during the machining process can be easily tracked by monitoring the deflection of the workpiece. During the cutter exiting the workpiece stage, the workpiece experiences forced vibration firstly, and free vibration exists until the amplitude reduces to zero after the cutter exits the workpiece. Machining results confirmed the suitability of the deflection monitoring system for machining thin-walled workpieces with the application of PVDF sensors.

  9. Real-Time Deflection Monitoring for Milling of a Thin-Walled Workpiece by Using PVDF Thin-Film Sensors with a Cantilevered Beam as a Case Study.

    Science.gov (United States)

    Luo, Ming; Liu, Dongsheng; Luo, Huan

    2016-09-10

    Thin-walled workpieces, such as aero-engine blisks and casings, are usually made of hard-to-cut materials. The wall thickness is very small and it is easy to deflect during milling process under dynamic cutting forces, leading to inaccurate workpiece dimensions and poor surface integrity. To understand the workpiece deflection behavior in a machining process, a new real-time nonintrusive method for deflection monitoring is presented, and a detailed analysis of workpiece deflection for different machining stages of the whole machining process is discussed. The thin-film polyvinylidene fluoride (PVDF) sensor is attached to the non-machining surface of the workpiece to copy the deflection excited by the dynamic cutting force. The relationship between the input deflection and the output voltage of the monitoring system is calibrated by testing. Monitored workpiece deflection results show that the workpiece experiences obvious vibration during the cutter entering the workpiece stage, and vibration during the machining process can be easily tracked by monitoring the deflection of the workpiece. During the cutter exiting the workpiece stage, the workpiece experiences forced vibration firstly, and free vibration exists until the amplitude reduces to zero after the cutter exits the workpiece. Machining results confirmed the suitability of the deflection monitoring system for machining thin-walled workpieces with the application of PVDF sensors.

  10. Astronomical Spectroscopy

    CERN Document Server

    Massey, Philip

    2010-01-01

    Spectroscopy is one of the most important tools that an astronomer has for studying the universe. This chapter begins by discussing the basics, including the different types of optical spectrographs, with extension to the ultraviolet and the near-infrared. Emphasis is given to the fundamentals of how spectrographs are used, and the trade-offs involved in designing an observational experiment. It then covers observing and reduction techniques, noting that some of the standard practices of flat-fielding often actually degrade the quality of the data rather than improve it. Although the focus is on point sources, spatially resolved spectroscopy of extended sources is also briefly discussed. Discussion of differential extinction, the impact of crowding, multi-object techniques, optimal extractions, flat-fielding considerations, and determining radial velocities and velocity dispersions provide the spectroscopist with the fundamentals needed to obtain the best data. Finally the chapter combines the previous materi...

  11. Grain Spectroscopy

    Science.gov (United States)

    Allamandola, L. J.

    1992-01-01

    Our fundamental knowledge of interstellar grain composition has grown substantially during the past two decades thanks to significant advances in two areas: astronomical infrared spectroscopy and laboratory astrophysics. The opening of the mid-infrared, the spectral range from 4000-400 cm(sup -1) (2.5-25 microns), to spectroscopic study has been critical to this progress because spectroscopy in this region reveals more about a materials molecular composition and structure than any other physical property. Infrared spectra which are diagnostic of interstellar grain composition fall into two categories: absorption spectra of the dense and diffuse interstellar media, and emission spectra from UV-Vis rich dusty regions. The former will be presented in some detail, with the latter only very briefly mentioned. This paper summarized what we have learned from these spectra and presents 'doorway' references into the literature. Detailed reviews of many aspects of interstellar dust are given.

  12. Influence of immediate dentin sealing techniques on cuspal deflection and fracture resistance of teeth restored with composite resin inlays.

    Science.gov (United States)

    Oliveira, L; Mota, E G; Borges, G A; Burnett, L H; Spohr, A M

    2014-01-01

    SUMMARY This research evaluated the influence of immediate dentin sealing (IDS) techniques on cuspal deflection and fracture resistance of teeth restored with composite resin inlays. Forty-eight maxillary premolars were divided into four groups: G1, sound teeth (control); G2, without IDS; G3, IDS with Clearfil SE Bond (CSE); and G4, IDS with CSE and Protect Liner F. The teeth from groups 2, 3, and 4 received mesio-distal-occlusal preparations. The impressions were made with vinyl polysiloxane, followed by provisional restoration and storage in water for seven days. The impressions were poured using type IV die stone, and inlays with Filtek Z250 composite resin were built over each cast. The inlays were luted with Panavia F. After storage in water for 72 hours, a 200-N load was applied on the occlusal surface using a metal sphere connected to a universal testing machine, and the cuspal deflection was measured with a micrometer. The specimens were then submitted to an axial load until failure. The following mean cuspal deflection (μm) and mean fracture resistance (N) followed by the same lowercase letter represent no statistical difference by analysis of variance and Tukey (p<0.05): cuspal deflection: G1, 3.1 ± 1.5(a); G2, 10.3 ± 4.6(b); G3, 5.5 ± 1.8(ac); and G4, 7.7 ± 5.1(bc); fracture resistance: G1, 1974 ± 708(a); G2, 1162 ± 474(b); G3, 700 ± 280(b); and G4, 810 ± 343(b). IDS with CSE allowed cuspal deflection comparable with that associated with sound teeth. The application of Protect Liner F did not contribute to a decrease in cuspal deflection. The IDS techniques did not influence the fracture resistance of teeth.

  13. Simplified model for the analysis on the duct wall deflection due to in-reactor creep in LMFBR fuel assemblies

    Science.gov (United States)

    Komoda, S.; Nakae, N.; Matsumoto, M.

    1992-06-01

    Each of the six walls of the duct tube is modeled as a straight beam being in plane strain prevented from lateral displacement at supported ends and bent by internal coolant pressure. The equation to predict the creep deflection curve is derived on the basis of this simplified model. To confirm the validity of the equation, the finite element analysis is performed, and it is found that the creep deflection curve predicted by the equation is in good agreement with that obtained by the analysis.

  14. Maximum Stress Estimation Model for Multi-Span Waler Beams with Deflections at the Supports Using Average Strains

    OpenAIRE

    Sung Woo Park; Byung Kwan Oh; Hyo Seon Park

    2015-01-01

    The safety of a multi-span waler beam subjected simultaneously to a distributed load and deflections at its supports can be secured by limiting the maximum stress of the beam to a specific value to prevent the beam from reaching a limit state for failure or collapse. Despite the fact that the vast majority of accidents on construction sites occur at waler beams in retaining wall systems, no safety monitoring model that can consider deflections at the supports of the beam is available. In this...

  15. Three-dimensional thermal-conductivity-tensor measurement of a polymer crystal by photothermal probe-beam deflection

    Science.gov (United States)

    Quelin, Xavier; Perrin, Bernard; Louis, Gérard; Peretti, Pierre

    1993-08-01

    Using Fourier transforms we have calculated the solutions of the three-dimensional (3D) thermal-conduction equation in an anisotropic medium. The temperature distribution at the surface of the sample and a 3D thermal-conductivity tensor is measured by the photothermal-probe-beam-deflection technique. We show that the expression for the deflection angle can be the same as in an isotropic medium, provided that an effective thermal conductivity relative to the polymeric-chain axis and a rescaled sample thickness are considered. This theoretical model is found to be in good agreement with the experimental data for an orthorhombic polydiacetylene sample (4BCMU).

  16. Fibre-Coupling Zig-Zag Beam Deflection Technology for Investigation of Attenuation Process of Laser-Induced Shock Waves

    Institute of Scientific and Technical Information of China (English)

    ZHANG Ping; BIAN Bao-Min; LI Zhen-Hua

    2005-01-01

    @@ A novel fibre-coupling zig-zag beam deflection technology is developed to investigate the attenuation process of laser-induced shock waves in air. Utilizing ordinal reflections of probe beams by a pair of parallel mirrors,a zig-zag beam field is formed, which has eleven probe beams in the horizontal plane. When a laser-induced shock wave propagates through the testing field, it causes eleven deflection signals one after another. The whole attenuation process of the shock wave in air can be detected and illuminated clearly on one experimental curve.

  17. An Application of Two Experimental Modal Analysis Methods for the Determination of Operational Deflection Shapes

    Science.gov (United States)

    Kromulski, J.; Hojan, E.

    1996-10-01

    Two methods are presented for the determination of operational deflection shapes (ODSs). The first method allows one to determine the ODSs by measuring mechanical vibrations at test points of the operating machine (created by the forces occurring in the actual work cycle). The second method is based on the modal model of the machine, including the forces which occur in the operation process, and yields the operational modes of vibration. The forces introduced into the model are determined by methods of pseudo-inversion of the matrix of the spectral transmissibility functions of the mechanical system and the vector of operating vibrations. The determination of the forces involved is necessary for the definition of the paths of energy transfer and the analysis of the noise emitted by the mechanical system (machine).

  18. Full deflection profile calculation and Young’s modulus optimisation for engineered high performance materials

    Science.gov (United States)

    Farsi, A.; Pullen, A. D.; Latham, J. P.; Bowen, J.; Carlsson, M.; Stitt, E. H.; Marigo, M.

    2017-04-01

    New engineered materials have critical applications in different fields in medicine, engineering and technology but their enhanced mechanical performances are significantly affected by the microstructural design and the sintering process used in their manufacture. This work introduces (i) a methodology for the calculation of the full deflection profile from video recordings of bending tests, (ii) an optimisation algorithm for the characterisation of Young’s modulus, (iii) a quantification of the effects of optical distortions and (iv) a comparison with other standard tests. The results presented in this paper show the capabilities of this procedure to evaluate the Young’s modulus of highly stiff materials with greater accuracy than previously possible with bending tests, by employing all the available information from the video recording of the tests. This methodology extends to this class of materials the possibility to evaluate both the elastic modulus and the tensile strength with a single mechanical test, without the need for other experimental tools.

  19. A note on the Charleston Gyre. [Gulf Stream deflection off Georgia-South Carolina coast

    Science.gov (United States)

    Mcclain, C. R.; Atkinson, L. P.

    1985-01-01

    The deflection of the Gulf Stream caused by a topographic feature - the Charleston Bump, located offshore of Savannah, Georgia - results in a quasi-stationary cyclonic eddy - the Charleston Gyre which is situated over the continental slope east of Charleston and Cape Romain. Occasionally, the upwelling associated with this eddy produces an enhancement in the surface layer primary production that is great enough to be detected by the Nimbus 7 coastal zone color scanner (CZCS). In this note a CZCS image with simultaneous hydrography, current, and wind observations is presented that documents an unusual manifestation of the gyre. In addition to the CZCS image a Seasat synthetic aperture radar (SAR) image is included that clearly indicates the presence of the eddy adjacent to the Gulf Stream front.

  20. Vertical dynamic deflection measurement in concrete beams with the Microsoft Kinect.

    Science.gov (United States)

    Qi, Xiaojuan; Lichti, Derek; El-Badry, Mamdouh; Chow, Jacky; Ang, Kathleen

    2014-02-19

    The Microsoft Kinect is arguably the most popular RGB-D camera currently on the market, partially due to its low cost. It offers many advantages for the measurement of dynamic phenomena since it can directly measure three-dimensional coordinates of objects at video frame rate using a single sensor. This paper presents the results of an investigation into the development of a Microsoft Kinect-based system for measuring the deflection of reinforced concrete beams subjected to cyclic loads. New segmentation methods for object extraction from the Kinect's depth imagery and vertical displacement reconstruction algorithms have been developed and implemented to reconstruct the time-dependent displacement of concrete beams tested in laboratory conditions. The results demonstrate that the amplitude and frequency of the vertical displacements can be reconstructed with submillimetre and milliHz-level precision and accuracy, respectively.

  1. Energy transfer via sunshades and light deflection elements; Energietransport durch Sonnenschutzsysteme und Lichtlenkelemente

    Energy Technology Data Exchange (ETDEWEB)

    Haug, I.

    2001-07-01

    The author investigated energy transfer via sunshades and light deflection elements. The information will be required for the development of external wall elements. The investigations are funded by Deutsche Bundesstiftung Umwelt. [German] Im Rahmen dieser Arbeit wurde der Energietransport durch eine herkoemmliche Waermeschutzverglasung mit innen liegender Jalousie, durch eine neuartige, lichtumlenkende LIF-Verglasung und durch eine lichtstreuende Kapillarverglasung untersucht. - Die Kenntnisse ueber den Energietransport werden benoetigt, um energetische Kennzahlen fuer Fassadenelemente bestimmen zu koennen, die in der Bauphysik und hinsichtlich des aktuellen Gesetzgebungsverfahren eine wesentliche Rolle spielen. - Der Energietransport, der sich aus Strahlungstransport und Waermetransport zusammensetzt, und die zugehoerigen energetischen Kennzahlen wurden fuer die genannten Systeme modelliert und messtechnisch erfasst. Diese Arbeit wurde durch die Deutsche Bundesstiftung Umwelt gefoerdert. (orig.)

  2. Static deflection control of flexible beams by piezo-electric actuators

    Science.gov (United States)

    Baz, A. M.

    1986-01-01

    This study deals with the utilization of piezo-electric actuators in controlling the static deformation of flexible beams. An optimum design procedure is presented to enable the selection of the optimal location, thickness and excitation voltage of the piezo-electric actuators in a way that would minimize the deflection of the beam to which these actuators are bonded. Numerical examples are presented to illustrate the application of the developed optimization procedure in minimizing the structural deformation of beams of different materials when subjected to different loading and end conditions using ceramic or polymeric piezo-electric actuators. The results obtained emphasize the importance of the devised rational procedure in designing beam-actuator systems with minimal elastic distortions.

  3. Weak lensing power spectra for precision cosmology: Multiple-deflection, reduced shear and lensing bias corrections

    CERN Document Server

    Krause, Elisabeth

    2009-01-01

    It is usually assumed that the ellipticity power spectrum measured in weak lensing observations can be expressed as an integral over the underlying matter power spectrum. This is true at second order in the gravitational potential. We extend the standard calculation, constructing all corrections to fourth order in the gravitational potential. There are four types of corrections: corrections to the lensing shear due to multiple-deflections; corrections due to the fact that shape distortions probe the reduced shear $\\gamma/(1-\\kappa)$ rather than the shear itself; corrections associated with the non-linear conversion of reduced shear to mean ellipticity; and corrections due to the fact that observational galaxy selection and shear measurement is based on galaxy brightnesses and sizes which have been (de)magnified by lensing. We show how the previously considered corrections to the shear power spectrum correspond to terms in our analysis, and highlight new terms that were not previously identified. All correctio...

  4. Strong deflection limit lensing effects in the minimal geometric deformation and Casadio-Fabbri-Mazzacurati solutions

    Science.gov (United States)

    Cavalcanti, R. T.; Goncalves da Silva, A.; da Rocha, Roldão

    2016-11-01

    In this paper we apply the strong deflection limit approach to investigate the gravitational lensing phenomena beyond general relativity. This is accomplished by considering the lensing effects related to black hole solutions that emerge out of the domain of Einstein gravity, namely, the ones acquired from the method of geometric deformation and the Casadio-Fabbri-Mazzacurati (CFM) brane-world black holes. The lensing observables, for those brane-world black hole metrics, are compared with the standard ones for the Schwarzschild case. We prove that brane-world black holes could have significantly different observational signatures, compared to the Schwarzschild black hole, with terms containing the post-Newtonian parameter, for the case of the CFM, and terms with variable brane-world tension, for the method of geometric deformation.

  5. Study of laser-induced plasma shock waves by the probe beam deflection technique

    Institute of Scientific and Technical Information of China (English)

    Yan Qian; Jian Lu; Xiaowu Ni

    2009-01-01

    Laser probe beam deflection technique is used for the analysis of laser-induced plasma shock waves in air and distilled water.The temporal and spatial variations of the parameters on shock fronts are studied as funotions of focal lens position and laser energy.The influences of the characteristics of media are investigated on the well-designed experimental setup.It is found that the shock wave in distilled water attenuates to an acoustic wave faster than in air under the same laser energy.Good agreement is obtained between our experimental results and those attained with other techniques.This technique is versatile,economic,and simple to implement,being a pronmising diagnostic tool for pulsed laser processing.

  6. Approximations for Large Deflection of a Cantilever Beam under a Terminal Follower Force and Nonlinear Pendulum

    Directory of Open Access Journals (Sweden)

    H. Vázquez-Leal

    2013-01-01

    Full Text Available In theoretical mechanics field, solution methods for nonlinear differential equations are very important because many problems are modelled using such equations. In particular, large deflection of a cantilever beam under a terminal follower force and nonlinear pendulum problem can be described by the same nonlinear differential equation. Therefore, in this work, we propose some approximate solutions for both problems using nonlinearities distribution homotopy perturbation method, homotopy perturbation method, and combinations with Laplace-Padé posttreatment. We will show the high accuracy of the proposed cantilever solutions, which are in good agreement with other reported solutions. Finally, for the pendulum case, the proposed approximation was useful to predict, accurately, the period for an angle up to 179.99999999∘ yielding a relative error of 0.01222747.

  7. Kidnapping small icy asteroids in Earth near encounter to harbour life and to deflect trajectory

    Science.gov (United States)

    Fargion, Daniele

    2016-07-01

    The inter-planetary flight for human being is under danger because of unscreened and lethal solar flare radioactive showers. The screening of the astronauts by huge superconducting magnetic fields is unrealistic by many reasons. On the contrary the ability to reach nearby icy asteroids, to harbour there a complete undergound room where ecological life systems are first set, this goal may offer a later natural and safe currier for future human stations and enterprise. The need to deflect such a small size (a few thousands tons objects) maybe achieved by micro nuclear engines able to dig the asteroid icy skin, to heat and propel the soil by a synchronous jet engine array, bending and driving it to any desired trajectories. The need for such a wide collection of icy asteroid stations, often in a robotic ibernated state, it will offer the safe help station, raft in the wide space sea, where to collect material or energy in long human planetary travels.

  8. Ludwig-Soret effect of non-ionic surfactant aqueous solution studied by beam deflection method

    Science.gov (United States)

    Maeda, Kousaku; Kita, Rio; Shinyashiki, Naoki; Yagihara, Shin

    2013-02-01

    We have studied the thermal diffusion of non-ionic surfactant aqueous solutions by a beam deflection method. The thermal diffusion of pentaethylene glycol monododecyl ether (C12E5) and hexaethylene glycol monododecyl ether (C12E6) is studied in the concentration range of 1.0-99.0 wt% and in the temperature range of 20.0-35.0 °C. A stable temperature gradient is applied to the solution, where solute molecules shift to the cold side of the solution for lowconcentration samples. The concentration dependence of the Soret coefficient ST of the C12E6 aqueous solution shows a sign inversion behavior. At all concentrations, the developed concentration gradient is proportionally related to the applied temperature gradient. The results confirm that the magnitude of ST has no temperature gradient dependence under the studied experimental conditions.

  9. Deflection of light in equatorial plane due to Kerr-Taub-NUT body

    Directory of Open Access Journals (Sweden)

    Chakraborty Sarani

    2017-01-01

    Full Text Available According to General Relativity, there are factors like mass, rotation, charge and presence of Cosmological constant that can influence the path of light ray. Apart from these factors, many authors have also reported the influence of gravitomagnetism on the path of light ray. In this study we have discussed the effect of a rotating Kerr-Taub-NUT body where the strength of the gravitomagnetic monopole is represented by the NUT factor or magnetic mass. We use the null geodesic of photon method to obtain the deflection angle of light ray for a Kerr-Taub-NUT body in equatorial plane upto the fourth order term. Our study shows that the NUT factor has a noticeable effect on the path of the light ray. By considering the magnetism to be zero, the expression of bending angle gets reduced to the Kerr bending angle. However, we obtained a non-zero bending angle for a hypothetical massless, magnetic body.

  10. Numerical Solution of Membrane Forces for A Free-Free Floating Plate with Large Deflection

    Institute of Scientific and Technical Information of China (English)

    陈徐均; 崔维成; 宋皓; 汤雪峰

    2003-01-01

    Considering that the thickness of a pontoon-type very large floating structure (VLFS) is very small in comparison with the length and width, VLFS can be modeled as a thin plate. In theory, the displacements and the membrane forces of a plate with large deflection are all the functions of the second-order differentials of the Ariy stress function. With these characteristics considered, the Ariy stress function of a floating free-free plate is calculated by setting the virtual values of three of the corner points. The finite difference method is chosen to solve the problem. When the Ariy stress function of the plate is obtained, the membrane forces can easily be calculated. Comparisons between the forces induced by the membrane forces and by the fluid are considered. It is shown that the membrane forces can not be neglected in many cases.

  11. Implementation of Radio-Frequency Deflecting Devices for Comprehensive High-Energy Electron Beam Diagnosis

    Science.gov (United States)

    Craievich, Paolo; Petronio, Marco; Biedron, Sandra G.; Castronovo, Davide; Dal Forno, Massimo; Di Mitri, Simone; Faure, Nicolas; La Civita, Daniele; Penco, Giuseppe; Rumiz, Luca; Sturari, Luca; Vescovo, Roberto; Wang, Defa

    2015-02-01

    In next-generation light sources, high-brightness electron beams are used in a free-electron laser configuration to produce light for use by scientists and engineers in numerous fields of research. High-brightness beams are described for such light sources as having low transverse and longitudinal emittances, high peak currents, and low slice emittance and energy spread. The optimal generation and preservation of such high-brightness electron beams during the acceleration process and propagation to and through the photon-producing element is imperative to the quality and performance of the light source. To understand the electron beam's phase space in the accelerating section of a next-generation light source machine, we employed radio-frequency cavities operating in a deflecting mode in conjunction with a magnetic spectrometer and imaging system for both low (250 MeV) and high (1.2 GeV) electron energies. This high-resolution, high-energy system is an essential diagnostic for the optimization and control of the electron beam in the FERMI light source generating fully transversely and longitudinally coherent light in the VUV to soft x-ray wavelength regimes. This device is located at the end of the linear accelerator in order to provide the longitudinal phase space nearest to the entrance of the photon-producing beam-lines. Here, we describe the design, fabrication, characterization, commissioning, and operational implementation of this transverse deflecting cavity structure diagnostic system for the high-energy (1.2 GeV) regime.

  12. Nuclear spectroscopy

    CERN Document Server

    Ajzenberg-Selove, Fay

    1960-01-01

    Nuclear Spectroscopy, Part B focuses on the ways in which experimental data may be analyzed to furnish information about nuclear parameters and nuclear models in terms of which the data are interpreted.This book discusses the elastic and inelastic potential scattering amplitudes, role of beta decay in nuclear physics, and general selection rules for electromagnetic transitions. The nuclear shell model, fundamental coupling procedure, vibrational spectra, and empirical determination of the complex potential are also covered. This publication is suitable for graduate students preparing for exper

  13. Laser spectroscopy

    CERN Document Server

    Demtröder, Wolfgang

    2008-01-01

    Keeping abreast of the latest techniques and applications, this new edition of the standard reference and graduate text on laser spectroscopy has been completely revised and expanded. While the general concept is unchanged, the new edition features a broad array of new material, e.g., frequency doubling in external cavities, reliable cw-parametric oscillators, tunable narrow-band UV sources, more sensitive detection techniques, tunable femtosecond and sub-femtosecond lasers (X-ray region and the attosecond range), control of atomic and molecular excitations, frequency combs able to synchronize independent femtosecond lasers, coherent matter waves, and still more applications in chemical analysis, medical diagnostics, and engineering.

  14. Laser assisted nuclear decay spectroscopy: A new method for studying neutron-deficient francium

    CERN Document Server

    Lynch, Kara Marie

    2015-01-01

    Radioactive decay studies of rare isotopes produced at radioactive ion beam facilities have often been hindered by the presence of isobaric and isomeric contamination. The Collinear Resonance Ionization Spectroscopy (CRIS) experiment at ISOLDE, CERN uses laser radiation to stepwise excite and ionize an atomic beam in a particular isomeric state. Deflection of this selectively ionized beam of exotic nuclei, from the remaining neutral contaminants, allows ultra-sensitive detection of rare isotopes and nuclear structure measurements in background-free conditions.\

  15. INFLUENCE OF DRAWING SPEED ON THE TEMPERATURE AND DEFLECTED MODE IN WIRE OF HIGH-CARBON STEEL

    Directory of Open Access Journals (Sweden)

    M. N. Vereshchagin

    2008-01-01

    Full Text Available The calculation of deflected mode and temperature fields with the help of the method of finite elements for zones of wire deformation in dies for current and new technology of drawing of wire with diameter 0,41 mm is carried out.

  16. Deflection in Flemish between the 13th and 20th Centuries: An Interplay between Analogical and Articulatory Factors.

    Science.gov (United States)

    Gerritsen, Marinel

    1992-01-01

    The linguistic embedding, transition, and actuation of the obliteration of the gerund ending "-e" in the West Flemish dialect of Bruges is examined. The study shows that deflection (loss of inflections) started in the fourteenth century and is almost complete today. (33 references) (Author/LB)

  17. Measurement of Deflection in Concrete Beams During Fatigue Loading Test Using the Microsoft Kinect 2.0

    Science.gov (United States)

    Lahamy, Herve; Lichti, Derek D.; Steward, Jeremy; El-Badry, Mamdouh; Moravvej, Mohammad

    2016-03-01

    This study focuses on 3 Hz fatigue load testing of a reinforced concrete beam in laboratory conditions. Three-dimensional (3D) image time series of the beam's top surface were captured with the Microsoft time-of-flight Kinect 2.0 sensor. To estimate the beam deflection, the imagery was first segmented to extract the top surface of the beam. The centre line was then modeled using third-order B-splines. The deflection of the beam as a function of time was estimated from the modeled centre line and, following past practice, also at several witness plates attached to the side of the beam. Subsequent correlation of the peak displacement with the applied loading cycles permitted estimation of fatigue in the beam. The accuracy of the deflections was evaluated by comparison with the measurements obtained using a Keyence LK-G407 laser displacement sensors. The results indicate that the deflections can be recovered with sub-millimetre accuracy using the centreline profile modelling method.

  18. Comparative Evaluation of Frictional Properties, Load Deflection Rate and Surface Characteristics of Different Coloured TMA Archwires - An Invitro Study.

    Science.gov (United States)

    Aloysius, Arul Pradeep; Vijayalakshmi, Devaki; Deepika; Soundararajan, Nagachandran Kandasamy; Manohar, Vijaykumar Neelam; Khan, Nayeemullah

    2015-12-01

    During tooth movement the success of sliding mechanics is dependent upon various factors which include frictional resistance at bracket-archwire interface, surface roughness of archwire materials and elastic properties of archwires. Ion implantation techniques reduce the frictional force and allow better tooth movement clinically. The main objective of this study was to evaluate and compare the frictional properties, load deflection rate and surface characteristics of Honey dew and Purple coloured (Ion implanted) TMA wires with uncoated TMA wires. Fifteen archwire samples were divided into three groups comprising of five samples in each group namely, Group I - Uncoated TMA wires (Control), Group II - Purple coloured TMA wires and Group III- Honey dew TMA wires. Friction and load deflection rate testing were performed with the Instron Universal testing machine and the surface characteristics of the wires were evaluated before and after sliding using Scanning Electron Microscope. The mean frictional characteristics and surface roughness for Honey dew TMA wires was lesser than Purple coloured TMA wires which was statistically significant. Both the coloured TMA wires showed low frictional characteristics and less surface roughness than uncoated TMA wires (the control). The mean load deflection rate was low for both coloured ion implanted TMA wires when compared to uncoated TMA wires which was statistically significant. Coloured ion implanted TMA wires, especially Honey dew TMA wires have low friction, low load deflection rate and improved surface finish. Hence they can be used in frictionless as well as sliding mechanics, where uncoated TMA wires are inefficient.

  19. Maximum Stress Estimation Model for Multi-Span Waler Beams with Deflections at the Supports Using Average Strains

    Directory of Open Access Journals (Sweden)

    Sung Woo Park

    2015-03-01

    Full Text Available The safety of a multi-span waler beam subjected simultaneously to a distributed load and deflections at its supports can be secured by limiting the maximum stress of the beam to a specific value to prevent the beam from reaching a limit state for failure or collapse. Despite the fact that the vast majority of accidents on construction sites occur at waler beams in retaining wall systems, no safety monitoring model that can consider deflections at the supports of the beam is available. In this paper, a maximum stress estimation model for a waler beam based on average strains measured from vibrating wire strain gauges (VWSGs, the most frequently used sensors in construction field, is presented. The model is derived by defining the relationship between the maximum stress and the average strains measured from VWSGs. In addition to the maximum stress, support reactions, deflections at supports, and the magnitudes of distributed loads for the beam structure can be identified by the estimation model using the average strains. Using simulation tests on two multi-span beams, the performance of the model is evaluated by estimating maximum stress, deflections at supports, support reactions, and the magnitudes of distributed loads.

  20. Laser self-mixing interferometry in VCSELs - an ultra-compact and massproduceable deflection detection system for nanomechanical polymer cantilever sensors

    DEFF Research Database (Denmark)

    Larsson, David; Yvind, Kresten; Hvam, Jørn Märcher;

    2008-01-01

    We have realised an ultra-compact deflection detection system based on laser self-mixing interferometry in a Vertical-Cavity Surface-Emitting Laser (VCSEL). The system can be used together with polymer nanomechanical cantilevers to form chemical sensors capable of detecting less than 1nm deflection....

  1. The Asteroid Impact and Deflection Assessment (AIDA) mission: Science Proximity Operations

    Science.gov (United States)

    Barnouin, Olivier; Bellerose, Julie; Carnelli, Ian; Carrol, Kieran; Ciarletti, Valérie; Cheng, Andrew F.; Galvez, Andres; Green, Simon F.; Grieger, Bjorn; Hirabayashi, Masatoshi; Herique, Alain; Kueppers, Michael; Minton, David A.; Mellab, Karim; Michel, Patrick; Rivkin, Andrew S.; Rosenblatt, Pascal; Tortora, Paolo; Ulamec, Stephan; Vincent, Jean-Baptiste; Zannoni, Marco

    2016-10-01

    The moon of the near-Earth binary asteroid 65803 Didymos is the target of the Asteroid Impact and Deflection Assessment (AIDA) mission. This mission is a joint effort between NASA and ESA to investigate the effectiveness of a kinetic impactor in deflecting an asteroid. The mission is composed of two components: the NASA-led Double Asteroid Redirect Test (DART) that will impact Didymos' moon (henceforth Didymos B), and the ESA-led Asteroid Impact Mission (AIM) that will survey the Didymos system. Both will undertake proximity operations to characterize the physical and dynamical properties of the Didymos system that are of maximum importance in the joint AIDA mission to understand the factors at play when assessing the mometum transfer that follows DART's impact into Didymos B. Using much of ESA's Rosetta experience, the AIM mission will undertake proximity operations both before and after DART's impact. AIM's chracterization includes measuring the precise orbital configuration, masses, internal properties, surface geology and regolith properties of the primary and secondary, using visible and thermal imaging, radar measurements and radio science data. AIM will also release the small MASCOT-2 lander, as well as a suite of a CubeSats to help achieve these objectives. DART proximity observations include two phases of imaging. The first makes use of a suite of long range images that will add light curve data to what will be collected from Earth. These data will refine the orbit period of Didymos B, and provide constraints for modeling the shape of both Didymos A and B. The second phase begins just under an hour before impact when resolved imaging of the Didymos system provides further shape model constraints for the visble parts of both Didymos A and B, some possible constraints on the mass of Didymos B and key geological information of both objects and the impact site. In this presentation, we will summarize the proximity operations undertaken by both DART and AIM

  2. Crossed, Small-Deflection Energy Analyzer for Wind/Temperature Spectrometer

    Science.gov (United States)

    Herrero, Federico A.; Finne, Theodore T.

    2010-01-01

    Determination of neutral winds and ion drifts in low-Earth-orbit missions requires measurements of the angular and energy distributions of the flux of neutrals and ions entering the satellite from the ram direction. The magnitude and direction of the neutral-wind (or ion-drift) determine the location of the maximum in the angular distribution of the flux. Knowledge of the angle of maximum flux with respect to satellite coordinates (pointing) is essential to determine the wind (or ion-drift) vector. The crossed Small-Deflection Energy Analyzer (SDEA) spectrometer (see Figure 1) occupies minimal volume and consumes minimal power. Designed for upper atmosphere/ionosphere investigations at Earth altitudes above 100 km, the spectrometer operates by detecting the angular and energy distributions of neutral atoms/molecules and ions in two mutually perpendicular planes. In this configuration, the two detection planes actually cross at the spectrometer center. It is possible to merge two SDEAs so they share a common optical axis and alternate measurements between two perpendicular planes, and reduce the number of ion sources from two to one. This minimizes the volume and footprint significantly and reduces the ion source power by a factor of two. The area of the entrance aperture affects the number of ions detected/second and also determines the energy resolution. Thermionic emitters require heater power of about 100 mW to produce 1 mA of electron beam current. Typically, electron energy is about 100 eV and requires a 100-V supply for electron acceleration to supply an additional 100 mW of power. Thus, ion source power is at most 200 mW. If two ion sources were to be used, the ion source power would be, at most, 400 mW. Detector power, deflection voltage power, and microcontroller and other functions require less than 150 mW. A WTS (wind/ temperature spectrometer) with two separate optical axes would consume about 650 mW, while the crossed SDEA described here consumes about

  3. Polylactic acid with improved heat deflection temperatures and self-healing properties for durable goods applications.

    Science.gov (United States)

    Wertz, J T; Mauldin, T C; Boday, D J

    2014-11-12

    A method to recover fracture toughness after failure and increase thermal properties of polylactic acid (PLA) for use within durable goods applications is presented. Microcapsules were incorporated into PLA to form a composite material in which the microcapsules served the dual purpose of (1) releasing self-healing additives to fracture regions and (2) serving as nucleating agents to improve the PLA composite's thermal tolerance. Self-healing was achieved though embedment of dicyclopentadiene-filled microcapsules and Grubbs' first generation ruthenium metathesis catalyst, the former being autonomically released into damage volumes and undergoing polymerization in the presence of the catalyst. This approach led to up to 84% recovery of the polymer composite's initial fracture toughness. Additionally, PLA's degree of crystallinity and heat deflection temperature were improved by ∼ 11% and ∼ 21 °C, respectively, relative to nonfilled virgin PLA, owing to microcapsule-induced nucleation. The self-healing system developed here overcomes many property limitations of PLA that can potentially lead to its incorporation into various durable goods.

  4. The role of tip deflection on the thrust produced by rigid flapping fins

    Science.gov (United States)

    Huera-Huarte, Francisco; Gharib, Morteza

    2015-11-01

    It is well known that flexibility plays an important role in the propulsion performance and efficiency of oscillating fin based propulsion systems. Compliance is one of the aspects that has received more attention, as it seems to be a common feature in nature's flyers and swimmers. Active control strategies are also common in nature. We will show how by deflecting only the last 10% of length of a rigid fin, at the tip, the thrust can be changed dramatically. This can be thought as an alternative to passive flexibility for controlling very efficiently the momentum transfer in the wake and therefore the thrust generation when flapping. A series of experiments have been carried with a robotic fin that allowed the control of its flapping kinematics as well as the control of the motions of its tip independently. We will be showing situations in which the tip was kept at a certain fixed position during a power stroke, and others in which it moved either in-phase or out-of-phase with the fin. The observed thrust and wake dynamics will be discussed for all these situations. The authors would like to acknowledge the financial support provided by the Gordon and Betty Moore Foundation and by the Spanish Ministerio de Economia y competitividad (MINECO) through grant DPI2012-37904. Visiting Associate in Aerospace, California Institute of Technology.

  5. New deflected-beam gauge for pressures below 10/sup -12/ Torr

    CERN Document Server

    Blechschmidt, Diether

    1975-01-01

    A new ionization gauge for measurement of total gas pressures between 10/sup -12/ torr and 10/sup -14/ torr is described. The gauge's main features are a pair of collimating slots below the grid structure, two concentric hemi-spherical deflecting electrodes and a channel electron multiplier which detects low-energy ions passing through the deflector system. The detection of low-energy ions allows discrimination against desorbed ions (which are more energetic), while spurious signals due to X-rays may also be rejected. The channel electron multiplier leads to gauge sensitivities which are much higher than those of ordinary ionization gauges. The gauge has been tested down to 4*10/sup -13/ torr and found to have sensitivities of 1.5*10/sup 17/ and 8*10/sup 16 / counts/s.A.torr for N/sub 2/ and H/sub 2/ respectively. For a channel electron multiplier gain of 10/sup 7/ the gauge sensitivity is thus approximately=10/sup 5//torr. (17 refs).

  6. Experimental and Numerical Analysis of Damage in Woven GFRP Composites Under Large-deflection Bending

    Science.gov (United States)

    Ullah, Himayat; Harland, Andy R.; Silberschmidt, Vadim V.

    2012-10-01

    Textile-reinforced composites such as glass fibre-reinforced polymer (GFRP) used in sports products can be exposed to different in-service conditions such as large bending deformation and multiple impacts. Such loading conditions cause high local stresses and strains, which result in multiple modes of damage and fracture in composite laminates due to their inherent heterogeneity and non-trivial microstructure. In this paper, various damage modes in GFRP laminates are studied using experimental material characterisation, non-destructive micro-structural damage evaluation and numerical simulations. Experimental tests are carried out to characterise the behaviour of these materials under large-deflection bending. To obtain in-plane shear properties of laminates, tensile tests are performed using a full-field strain-measurement digital image correlation technique. X-ray micro computed tomography (Micro CT) is used to investigate internal material damage modes - delamination and cracking. Two-dimensional finite element (FE) models are implemented in the commercial code Abaqus to study the deformation behaviour and damage in GFRP. In these models, multiple layers of bilinear cohesive-zone elements are employed to study the onset and progression of inter-ply delamination and intra-ply fabric fracture of composite laminate, based on the X-ray Micro CT study. The developed numerical models are capable to simulate these features with their mechanisms as well as subsequent mode coupling observed in tests and Micro CT scanning. The obtained results of simulations are in agreement with experimental data.

  7. Large deflections and vibrations of a tip pulled beam with variable transversal section

    Science.gov (United States)

    Kurka, P.; Izuka, J.; Gonzalez, P.; Teixeira, L. H.

    2016-10-01

    The use of long flexible probes in outdoors exploration vehicles, as opposed to short and rigid arms, is a convenient way to grant easier access to regions of scientific interest such as terrain slopes and cliff sides. Longer and taller arms can also provide information from a wider exploration horizon. The drawback of employing long and flexible exploration probes is the fact that its vibration is not easily controlled in real time operation by means of a simple analytic linear dynamic model. The numerical model required to describe the dynamics of a very long and flexible structure is often very large and of slow computational convergence. The present work proposes a simplified numerical model of a long flexible beam with variable cross section, which is statically deflected by a pulling cable. The paper compares the proposed simplified model with experimental data regarding the static and dynamic characteristics of a beam with variable cross section. The simulations show the effectiveness of the simplified dynamic model employed in an active control loop to suppress tip vibrations of the beam.

  8. Crack location identification of rotating rotor systems using operating deflection shape data

    Institute of Scientific and Technical Information of China (English)

    ZHANG; ChunLin; LI; Bing; YANG; ZhiBo; XIAO; WenRong; HE; ZhengJia

    2013-01-01

    Crack location identification, as one key destination of structural health monitoring, is still a challenge for operating rotor systems. The operating deflection shape (ODS), which represents a visual description of the structural vibration patterns under operating conditions, has been gaining importance for structure damage detection in recent years. The ODS carries damage information of a structure, however, it is also difficult to detect weak cracks of rotor directly. The approximate waveform capacity dimension (AWCD) method was successfully applied to damage detection of plates and beam-like structures. In this paper,a strategic approach that combines ODS and weighted AWCD is proposed for crack location identification of the rotating rotor.To eliminate the false peaks of AWCD and obtain desirable results, a weight factor and ODS curvature data are introduced to the expression of the weighted AWCD. The effectiveness of the proposed method is validated by numerical simulation and experimental investigation in a cracked rotor system. The results indicate that the proposed approach not only provides good identifying performance for incipient rotor cracks, but also effectively eliminates the fault peaks introduced by the inflexion locations of ODSs. Moreover, the proposed approach proves promising in detecting crack locations of rotating rotor systems.

  9. Probe beam deflection studies of nanostructured catalyst materials for fuel cells.

    Science.gov (United States)

    García, G; Bruno, M M; Planes, G A; Rodriguez, J L; Barbero, C A; Pastor, E

    2008-11-28

    Probe beam deflection (PBD) techniques, both as cyclic voltadeflectometry (CVD) and chronodeflectometry (CD), were applied for the first time to the study of the electrochemistry of nanostructured Pt materials which are commonly used as electrocatalysts in fuel cells. The electrochemical surface reactions, including faradaic processes, double layer charging and specific anion adsorption were easily detected. Quantitative analysis of the chronodeflectometric data made possible to elucidate the dynamics of double layer charging in such materials and to determine the potential of zero charge (pzc) of the metal present either as a monolithic mesoporous material or as metal nanoparticles supported on carbon. The electro-oxidation of CO, adsorbed on nanostructured Pt, was also studied by CVD and CD being able to detect the formation of CO2 and H3O+ related with the nucleation and growth process which controls the rate of CO stripping. The interplay of Pt oxide formation and COad electrooxidation, both in potential and time, was detected indicating possible application of the technique to other electrocatalysts.

  10. Electrostatic acceleration and deflection system for modification of semiconductor materials in laser-produced ion implantation

    Science.gov (United States)

    Rosinski, M.; Parys, P.; Wolowski, J.; Gasior, P.; Pisarek, M.

    2010-10-01

    To optimize the efficiency of laser ion implantation technology, it is advisable to properly select the laser beam characteristics (i.e. power density, target illumination geometry, etc.). In many applications, it is important to select a specific range of ion energy to implant the ions at a given depth and at a given density. To make it possible, the electrostatic system for acceleration and deflection of low-energy laser-produced ions can be used. This contribution provides a description of the experiments aimed at the implantation of Ge ions from a narrow energy band onto SiO2/Si substrates, which were conducted at IPPLM. As the source of irradiation, we used a Nd:YAG up to 10 Hz laser system with pulse duration of 3.5 ns and pulse energy ∼ 0.5 J, which gave a power density of 1010 W/cm2. The ion stream parameters were measured using the time-of-fight method. The laser-produced ions passing through the diaphragm have been accelerated in the system of electrodes. Due to the electrostatic field configuration provided by the electrode system and a diaphragm located at the axis of the system, the selected ions were focussed at the area of interest to increase implantation density. The accelerating voltage, the distance of the diaphragm from the target, the diaphragm diameter and the gap width between electrodes were changed for choosing the desired parameters of the ion stream.

  11. Optical Beam Deflection Based AFM with Integrated Hardware and Software Platform for an Undergraduate Engineering Laboratory

    Directory of Open Access Journals (Sweden)

    Siu Hong Loh

    2017-02-01

    Full Text Available Atomic force microscopy (AFM has been used extensively in nanoscience research since its invention. Recently, many teaching laboratories in colleges, undergraduate institutions, and even high schools incorporate AFM as an effective teaching tool for nanoscience education. This paper presents an optical beam deflection (OBD based atomic force microscope, designed specifically for the undergraduate engineering laboratory as a teaching instrument. An electronic module for signal conditioning was built with components that are commonly available in an undergraduate electronic laboratory. In addition to off-the-shelf mechanical parts and optics, the design of custom-built mechanical parts waskept as simple as possible. Hence, the overall cost for the setup is greatly reduced. The AFM controller was developed using National Instruments Educational Laboratory Virtual Instrumentation Suite (NI ELVIS, an integrated hardware and software platform which can be programmed in LabVIEW. A simple yet effective control algorithm for scanning and feedback control was developed. Despite the use of an educational platform and low-cost components from the undergraduate laboratory, the developed AFM is capable of performing imaging in constant-force mode with submicron resolution and at reasonable scanning speed (approximately 18 min per image. Therefore, the AFM is suitable to be used as an educational tool for nanoscience. Moreover, the construction of the system can be a valuable educational experience for electronic and mechanical engineering students.

  12. Measuring Starlight Deflection during the 2017 Eclipse: Repeating the Experiment that made Einstein Famous

    Science.gov (United States)

    Bruns, Donald

    2016-05-01

    In 1919, astronomers performed an experiment during a solar eclipse, attempting to measure the deflection of stars near the sun, in order to verify Einstein's theory of general relativity. The experiment was very difficult and the results were marginal, but the success made Albert Einstein famous around the world. Astronomers last repeated the experiment in 1973, achieving an error of 11%. In 2017, using amateur equipment and modern technology, I plan to repeat the experiment and achieve a 1% error. The best available star catalog will be used for star positions. Corrections for optical distortion and atmospheric refraction are better than 0.01 arcsec. During totality, I expect 7 or 8 measurable stars down to magnitude 9.5, based on analysis of previous eclipse measurements taken by amateurs. Reference images, taken near the sun during totality, will be used for precise calibration. Preliminary test runs performed during twilight in April 2016 and April 2017 can accurately simulate the sky conditions during totality, providing an accurate estimate of the final uncertainty.

  13. Assessment of the beam path deflection for a vertically installed microwave interferometer in SUNIST

    Science.gov (United States)

    Zhong, H.; Ling, B. L.; Tan, Y.; Gao, Z.

    2016-08-01

    Microwave interferometry has been widely employed to provide reliable line averaged electron density measurement on plasma devices. For a vertically installed interferometer on a tokamak, the refraction problem, which distorts the beam path and aggravates power loss at the receiving antenna, may become significant if taking the cross section shape into account. Increasing the frequency of the probing microwave can alleviate the distortion, but at the expense of losing the density resolution. To seek for an optimized frequency, previous calculations are mainly based on the cylindrical column geometry which grossly underestimates the deflection of the beam path induced by the plasma shape, and empirical suggestions indicating ne0/nc = 1/2 ˜ 1/3 may not always be the appropriate option. Here a single ray tracing method is applied to estimate the final horizontal deviation at the receiving antenna, which is supposed to represent the level of power loss. The calculation is carried out under the real tokamak geometry in Sino-UNIted Spherical Tokamak (SUNIST) with the cross section parameters obtained from the equilibrium reconstruction, and the result indicates that for a target density of 1.2 × 1019 m-3, a frequency of at least 100 GHz is desirable to reduce the power loss to an acceptable level. This would be helpful for the design of a vertically installed interferometer on SUNIST.

  14. Nonlinear flexural waves and chaos behavior in finite-deflection Timoshenko beam

    Institute of Scientific and Technical Information of China (English)

    Shan-yuan ZHANG; Zhi-fang LIU

    2010-01-01

    Based on the Timoshenko beam theory,the finite-deflection and the axial inertia are taken into account,and the nonlinear partial differential equations for flexural waves in a beam are derived. Using the traveling wave method and integration skills,the nonlinear partial differential equations can be converted into an ordinary differential equation. The qualitative analysis indicates that the corresponding dynamic system has a heteroclinic orbit under a certain condition. An exact periodic solution of the nonlinear wave equation is obtained using the Jacobi elliptic function expansion. When the modulus of the Jacobi elliptic function tends to one in the degenerate case,a shock wave solution is given. The small perturbations are further introduced,arising from the damping and the external load to an original Hamilton system,and the threshold condition of the existence of the transverse heteroclinic point is obtained using Melnikov's method. It is shown that the perturbed system has a chaotic property under the Smale horseshoe transform.

  15. Further development of the attitude difference method for estimating deflections of the vertical in real time

    Science.gov (United States)

    Zhu, Jing; Zhou, Zebo; Li, Yong; Rizos, Chris; Wang, Xingshu

    2016-07-01

    An improvement of the attitude difference method (ADM) to estimate deflections of the vertical (DOV) in real time is described in this paper. The ADM without offline processing estimates the DOV with a limited accuracy due to the response delay. The proposed model selection-based self-adaptive delay feedback (SDF) method takes the results of the ADM as the a priori information, then uses fitting and extrapolation to estimate the DOV at the current epoch. The active region selection factor F th is used to take full advantage of the Earth model EGM2008 and the SDF with different DOV exhibitions. The factors which affect the DOV estimation accuracy are analyzed and modeled. An external observation which is specified by the velocity difference between the global navigation satellite system (GNSS) and the inertial navigation system (INS) with DOV compensated is used to select the optimal model. The response delay induced by the weak observability of an integrated INS/GNSS to the violent DOV disturbances in the ADM is compensated. The DOV estimation accuracy of the SDF method is improved by approximately 40% and 50% respectively compared to that of the EGM2008 and the ADM. With an increase in GNSS accuracy, the DOV estimation accuracy could improve further.

  16. Blade Deflection Measurements of a Full-Scale UH-60A Rotor System

    Science.gov (United States)

    Olson, Lawrence E.; Abrego, Anita; Barrows, Danny A.; Burner, Alpheus W.

    2010-01-01

    Blade deflection (BD) measurements using stereo photogrammetry have been made during the individual blade control (IBC) testing of a UH-60A 4-bladed rotor system in the 40 by 80-foot test section of the National Full-Scale Aerodynamic Complex (NFAC). Measurements were made in quadrants one and two, encompassing advance ratios from 0.15 to 0.40, thrust coefficient/solidities from 0.05 to 0.12 and rotor-system drive shaft angles from 0.0 to -9.6 deg. The experiment represents a significant step toward providing benchmark databases to be utilized by theoreticians in the development and validation of rotorcraft prediction techniques. In addition to describing the stereo measurement technique and reporting on preliminary measurements made to date, the intent of this paper is to encourage feedback from the rotorcraft community concerning continued analysis of acquired data and to solicit suggestions for improved test technique and areas of emphasis for measurements in the upcoming UH-60A Airloads test at the NFAC.

  17. Steady-state sinusoidal thermal characterization at chip level by internal infrared-laser deflection

    Energy Technology Data Exchange (ETDEWEB)

    Perpina, Xavier; Jorda, Xavier; Vellvehi, Miquel [Centre Nacional de Microelectronica (IMB-CNM-CSIC), Campus UAB, 08193 Bellaterra, Barcelona (Spain); Altet, Josep [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Barcelona 08034 (Spain); Mestres, NarcIs [Institut de Ciencia dels Materials de Barcelona (ICMAB-CSIC), Campus UAB, 08193 Bellaterra, Barcelona (Spain)

    2008-08-07

    A new approach is reported for thermally characterizing microelectronic devices and integrated circuits under a steady-state sinusoidal regime by internal infrared-laser deflection (IIR-LD). It consists of extracting the amplitude and phase Bode plots of the temperature profile inside the chip (depth-resolved measurements in the frequency domain). As a consequence, not only are the IIR-LD performances significantly improved (accuracy, robustness to noise, control of boundary conditions and heat flux confinement) but also the direct temperature measurement is feasible when thin regions are inspected and thermal parameters can be easily extracted (thermal diffusivity). In order to show the efficiency of this technique, a thermal test chip (TTC) is used. The TTC is thermally excited by imposing a cosine-like voltage waveform. As a result, a vertical temperature profile inside the die is obtained depending on the heating frequency. Repeating this procedure at several frequencies, the frequency response of the chip internal temperature profile is derived. By comparing the experimental results with the model predictions, good agreement is achieved. This technique allows evaluation of the thermal behaviour at the chip level; also it could be useful for failure analysis.

  18. The Deflection Plate Analyzer: A Technique for Space Plasma Measurements Under Highly Disturbed Conditions

    Science.gov (United States)

    Wright, Kenneth H., Jr.; Dutton, Ken; Martinez, Nelson; Smith, Dennis; Stone, Nobie H.

    2004-01-01

    A technique has been developed to measure the characteristics of space plasmas under highly disturbed conditions; e.g., non-Maxwellian plasmas with strong drifting populations and plasmas contaminated by spacecraft outgassing. The present method is an extension of the capabilities of the Differential Ion Flux Probe (DIFP) to include a mass measurement that does not include either high voltage or contamination sensitive devices such as channeltron electron multipliers or microchannel plates. This reduces the complexity and expense of instrument fabrication, testing, and integration of flight hardware as compared to classical mass analyzers. The new instrument design is called the Deflection Plate Analyzer (DPA) and can deconvolve multiple ion streams and analyze each stream for ion flux intensity (density), velocity (including direction of motion), mass, and temperature (or energy distribution). The basic functionality of the DPA is discussed. The performance characteristics of a flight instrument as built for an electrodynamic tether mission, the Propulsive Small Expendable Deployer System (ProSEDS), and the instrument s role in measuring key experimental conditions are also discussed.

  19. Seesaw-deflected Anomaly Mediation and the 125 GeV Higgs Boson

    Science.gov (United States)

    Tran, Hieu Minh; Okada, Nobuchika

    2016-06-01

    We investigate the phenomenology of a class of model that at the same time solves the tachyonic slepton problem of the pure anomaly mediated supersymmetry breaking (AMSB) model and generates neutrino masses. We introduce heavy fields in the seesaw mechanism that are the messengers in the deflected AMSB scenario. Various theoretical and phenomenological constraints have been taken into account, especially the Higgs mass limits. The viable parameter regions have been specified, and the properties of dark matter candidate have been studied. We point out that the type III seesaw with three generations of 24-messenger is excluded, while the type II seesaw and type III seesaw with two generations of 24-messenger are still allowed. The sparticle masses are heavy as in usual SUSY models. The spin-independent crosssection of the scattering between the lightest neutralino and proton show the possibility to see evidences of new physics from future dark matter search experiments. We find that the lepton flavor violation effects caused by the Yukawa mediation are suppressed due to the electroweak symmetry breaking condition.

  20. Evidence for the Deflective Function of Eyespots in Wild Junonia evarete Cramer (Lepidoptera, Nymphalidae).

    Science.gov (United States)

    Pinheiro, C E G; Antezana, M A; Machado, L P

    2014-02-01

    Junonia evarete Cramer is a fast-flying butterfly that perches on the ground with wings opened exhibiting four eyespots close to wing borders. These eyespots presumably function either to intimidate predators, like insectivorous birds, or to deflect bird attacks to less vital parts of the body. We assessed the form, frequency, and location of beak marks on the wings of wild butterflies in central Brazil during two not consecutive years. We found that almost 50% of males and 80% of females bore signals of predator attacks (wing tears), most of them consisting of partially or totally V-shaped forms apparently produced by birds. Males were significantly less attacked and showed a lower proportion of attacks on eyespots than females, suggesting they are better to escape bird attacks. In contrast, females were heavily attacked on eyespots. Eyespot tears in females were higher (and significant different) than expected by chance, indicating that birds do attempt to reach the eyespots when striking on these butterflies. Other comparisons involving the proportion of tears directed or not directed to eyespots in males and females are presented and discussed.

  1. Reduction of Thermal Loss in HTS Windings by Using Magnetic Flux Deflection

    Science.gov (United States)

    Tsuzuki, K.; Miki, M.; Felder, B.; Koshiba, Y.; Izumi, M.; Umemoto, K.; Aizawa, K.; Yanamoto, T.

    Efforts on the generation of intensified magnetic flux have been made for the optimized shape of HTS winding applications. This contributes to the high efficiency of the rotating machines using HTS windings. Heat generation from the HTS windings requires to be suppressed as much as possible, when those coils are under operation with either direct or alternative currents. Presently, the reduction of such thermal loss generated by the applied currents on the HTS coils is reported with a magnetic flux deflection system. The HTS coils are fixed together with flattened magnetic materials to realize a kind of redirection of the flux pathway. Eventually, the magnetic flux density perpendicular to the tape surface (equivalent to the a-b plane) of the HTS tape materials is reduced to the proximity of the HTS coil. To verify the new geometry of the surroundings of the HTS coils with magnetic materials, a comparative study of the DC coil voltage was done for different applied currents in prototype field-pole coils of a ship propulsion motor.

  2. ATEFlap aerodynamic model, a dynamic stall model including the effects of trailing edge flap deflection

    Energy Technology Data Exchange (ETDEWEB)

    Bergami, L.; Gaunaa, M.

    2012-02-15

    The report presents the ATEFlap aerodynamic model, which computes the unsteady lift, drag and moment on a 2D airfoil section equipped with Adaptive Trailing Edge Flap. The model captures the unsteady response related to the effects of the vorticity shed into the wake, and the dynamics of flow separation a thin-airfoil potential flow model is merged with a dynamic stall model of the Beddoes-Leishmann type. The inputs required by the model are steady data for lift, drag, and moment coefficients as function of angle of attack and flap deflection. Further steady data used by the Beddoes- Leishmann dynamic stall model are computed in an external preprocessor application, which gives the user the possibility to verify, and eventually correct, the steady data passed to the aerodynamic model. The ATEFlap aerodynamic model is integrated in the aeroelastic simulation tool HAWC2, thus al- lowing to simulate the response of a wind turbine with trailing edge flaps on the rotor. The algorithms used by the preprocessor, and by aerodynamic model are presented, and modifications to previous implementations of the aerodynamic model are briefly discussed. The performance and the validity of the model are verified by comparing the dynamic response computed by the ATEFlap with solutions from CFD simulations. (Author)

  3. NEO-LISP: Deflecting near-Earth objects using high average power, repetitively pulsed lasers

    Science.gov (United States)

    Phipps, C. R.; Michaelis, M. M.

    Several kinds of Near-Earth objects exist for which one would like to cause modest orbit perturbations, but which are inaccessible to normal means of interception because of their number, distance or the lack of early warning. For these objects, LISP (Laser Impulse Space Propulsion) is an appropriate technique for rapidly applying the required mechanical impulse from a ground-based station. In order of increasing laser energy required, examples are: (1) repositioning specially prepared geosynchronous satellites for an enhanced lifetime; (2) causing selected items of space junk to re-enter and burn up in the atmosphere on a computed trajectory; and (3) safely deflecting Earth-directed comet nuclei and earth-crossing asteroids (ECA's) a few tens of meters in size (the most hazardous size). They will discuss each of these problems in turn and show that each application is best matched by its own matrix of LISP laser pulse width, pulse repetition rate, wavelength and average power. The latter ranges from 100W to 3GW for the cases considered. They will also discuss means of achieving the active beam phase error correction during passage through the atmosphere and very large exit pupil in the optical system which are required in each of these cases.

  4. Lactic acidosis, potassium, and the heart rate deflection point in professional road cyclists

    Science.gov (United States)

    Lucia, A; Hoyos, J; Santalla, A; Perez, M; Carvajal, A; Chicharro, J

    2002-01-01

    Objective: To determine the influence of lactic acidosis, the Bohr effect, and exercise induced hyperkalaemia on the occurrence of the heart rate deflection point (HRDP) in elite (professional) cyclists. Methods: Sixteen professional male road cyclists (mean (SD) age 26 (1) years) performed a ramp test on a cycle ergometer (workload increases of 5 W/12 s, averaging 25 W/min). Heart rate (HR), gas exchange parameters, and blood variables (lactate, pH, P50 of the oxyhaemoglobin dissociation curve, and K+) were measured during the tests. Results: A HRDP was shown in 56% of subjects at about 88% of their maximal HR (HRDP group; n = 9) but was linear in the rest (No-HRDP group; n = 7). In the HRDP group, the slope of the HR-workload regression line above the HRDP correlated inversely with levels of K+ at the maximal power output (r = -0.67; p<0.05). Conclusions: The HRDP phenomenon is associated, at least partly, with exercise induced hyperkalaemia. PMID:11916893

  5. Heart dimensions may influence the occurrence of the heart rate deflection point in highly trained cyclists

    Science.gov (United States)

    Lucia, A.; Carvajal, A.; Boraita, A.; Serratosa, L.; Hoyos, J.; Chicharro, J. L.

    1999-01-01

    OBJECTIVES: To determine whether the heart rate (HR) response to exercise in 21 highly trained cyclists (mean (SD) age 25 (3) years) was related to their heart dimensions. METHODS: Before performing an incremental exercise test involving a ramp protocol with workload increases of 25 W/min, each subject underwent echocardiographic evaluation of the following variables: left ventricular end diastolic internal diameter (LVIDd), left ventricular posterior wall thickness at end diastole (LVPWTd), interventricular septal wall thickness at end diastole (IVSTd), left ventricular mass index (LVMI), left atrial dimension (LAD), longitudinal left atrial (LLAD) and right atrial (LRAD) dimensions, and the ratio of early to late (E/A) diastolic flow velocity. RESULTS: The HR response showed a deflection point (HRd) at about 85% VO2MAX in 66.7% of subjects (D group; n = 14) and was linear in 33.3% (NoD group; n = 7). Several echocardiographic variables (LVMI, LAD, LLAD, LRAD) indicative of heart dimensions were similar in each group. However, mean LPWTd (p<0.01) and IVSTd (p<0.05) values were significantly higher in the D group. Finally, no significant difference between groups was found with respect to the E/A. CONCLUSIONS: The HR response is curvilinear during incremental exercise in a considerable number of highly trained endurance athletes-that is, top level cyclists. The departure of HR increase from linearity may predominantly occur in athletes with thicker heart walls. 


 PMID:10597846

  6. All-optical optoacoustic microscopy based on probe beam deflection technique

    Directory of Open Access Journals (Sweden)

    Saher M. Maswadi

    2016-09-01

    Full Text Available Optoacoustic (OA microscopy using an all-optical system based on the probe beam deflection technique (PBDT for detection of laser-induced acoustic signals was investigated as an alternative to conventional piezoelectric transducers. PBDT provides a number of advantages for OA microscopy including (i efficient coupling of laser excitation energy to the samples being imaged through the probing laser beam, (ii undistorted coupling of acoustic waves to the detector without the need for separation of the optical and acoustic paths, (iii high sensitivity and (iv ultrawide bandwidth. Because of the unimpeded optical path in PBDT, diffraction-limited lateral resolution can be readily achieved. The sensitivity of the current PBDT sensor of 22 μV/Pa and its noise equivalent pressure (NEP of 11.4 Pa are comparable with these parameters of the optical micro-ring resonator and commercial piezoelectric ultrasonic transducers. Benefits of the present prototype OA microscope were demonstrated by successfully resolving micron-size details in histological sections of cardiac muscle.

  7. ASTEROFF: A Computer Code to Deflect NEOs by Missiles shot from L1 and L3 (Earth-Moon)

    Science.gov (United States)

    Maccone, C.

    We develop the mathematical theory for an automatic, space-based system to deflect NEOs by virtue of missiles shot from the Earth-Moon L1 and L3 Lagrangian Points. A patent application has been filed for the relevant code, dubbed ASTEROFF (= Asteroids OFF !). This code was already implemented, and a copyright for it was registered. In a paper published in Acta Astronautica, Vol. 50, No. 3, pp. 185-199 (2002), this author proved mathematically the following theorem (hereafter called the ``confocal conics theorem''): ``Within the sphere of influence of the Earth, any NEO could be hit by a missile at just an angle of 90 degrees, was the missile shot from Lagrangian Points L1 or L3 of the Earth-Moon system, rather than from the surface of the Earth''. As a consequence, the hitting missile would have move along a ``confocal ellipse'' (centered at the Earth) uniquely determined by the NEO's incoming hyperbola. Based on the above theorem, the author further shows in this paper that: The proposed defense system would be ideal to deflect NEOs that are small, i.e. less than one kilometer in diameter. Small NEOs are just the most difficult ones to be detected early enough and to such an orbital accuracy to be positively sure that they are indeed hazardous. The traditional theory of Keplerian orbits can successfully be applied to get an excellent first-order approximation of the (otherwise unknown) mathematical formulae of the energy/momentum requested to achieve the NEO deflection. Many engineering details about the missiles shot from L1 and L3, however, still have to be implemented into our simulations, partly because they are classified. Was one missile not enough to deflect the NEO completely, it is a great advantage of the ``confocal conics'' used here that the new, slightly deflected NEO's hyperbola would certainly be hit at nearly 90 degrees by another and slightly more eccentric elliptical missile trajectory. A sufficient number of missiles could thus be launched in a

  8. SIMP spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Hochberg, Yonit [Ernest Orlando Lawrence Berkeley National Laboratory, University of California,Berkeley, CA 94720 (United States); Department of Physics, University of California,Berkeley, CA 94720 (United States); Kuflik, Eric [Department of Physics, LEPP, Cornell University,Ithaca NY 14853 (United States); Murayama, Hitoshi [Ernest Orlando Lawrence Berkeley National Laboratory, University of California,Berkeley, CA 94720 (United States); Department of Physics, University of California,Berkeley, CA 94720 (United States); Kavli Institute for the Physics and Mathematics of the Universe (WPI),University of Tokyo Institutes for Advanced Study, University of Tokyo,Kashiwa 277-8583 (Japan); Center for Japanese Studies, University of California,Berkeley, CA 94720 (United States)

    2016-05-16

    We study the interactions between strongly interacting massive particle dark matter and the Standard Model via a massive vector boson that is kinetically mixed with the hypercharge gauge boson. The relic abundance is set by 3→2 self-interactions of the dark matter, while the interactions with the vector mediator enable kinetic equilibrium between the dark and visible sectors. We show that a wide range of parameters is phenomenologically viable and can be probed in various ways. Astrophysical and cosmological constraints are evaded due to the p-wave nature of dark matter annihilation into visible particles, while direct detection methods using electron recoils can be sensitive to parts of the parameter space. In addition, we propose performing spectroscopy of the strongly coupled dark sector at e{sup +}e{sup −} colliders, where the energy of a mono-photon can track the resonance structure of the dark sector. Alternatively, some resonances may decay back into Standard Model leptons or jets, realizing ‘hidden valley’ phenomenology at the LHC and ILC in a concrete fashion.

  9. 3D COMSOL Simulations for Thermal Deflection of HFIR Fuel Plate in the "Cheverton-Kelley" Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Jain, Prashant K [ORNL; Freels, James D [ORNL; Cook, David Howard [ORNL

    2012-08-01

    Three dimensional simulation capabilities are currently being developed at Oak Ridge National Laboratory using COMSOL Multiphysics, a finite element modeling software, to investigate thermal expansion of High Flux Isotope Reactor (HFIR) s low enriched uranium fuel plates. To validate simulations, 3D models have also been developed for the experimental setup used by Cheverton and Kelley in 1968 to investigate the buckling and thermal deflections of HFIR s highly enriched uranium fuel plates. Results for several simulations are presented in this report, and comparisons with the experimental data are provided when data are available. A close agreement between the simulation results and experimental findings demonstrates that the COMSOL simulations are able to capture the thermal expansion physics accurately and that COMSOL could be deployed as a predictive tool for more advanced computations at realistic HFIR conditions to study temperature-induced fuel plate deflection behavior.

  10. Large deflection angle, high-power adaptive fiber optics collimator with preserved near-diffraction-limited beam quality.

    Science.gov (United States)

    Zhi, Dong; Ma, Yanxing; Chen, Zilun; Wang, Xiaolin; Zhou, Pu; Si, Lei

    2016-05-15

    We report on the development of a monolithic adaptive fiber optics collimator, with a large deflection angle and preserved near-diffraction-limited beam quality, that has been tested at a maximal output power at the 300 W level. Additionally, a new measurement method of beam quality (M2 factor) is developed. Experimental results show that the deflection angle of the collimated beam is in the range of 0-0.27 mrad in the X direction and 0-0.19 mrad in the Y direction. The effective working frequency of the device is about 710 Hz. By employing the new measurement method of the M2 factor, we calculate that the beam quality is Mx2=1.35 and My2=1.24, which is in agreement with the result from the beam propagation analyzer and is preserved well with the increasing output power.

  11. ANALYTICAL EVALUATION OF PERMANENT DEFLECTION OF A THIN CIRCULAR PLATE STRUCK NORMALLY AT ITS CENTER BY A PROJECTILE

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The permanent deflection of a thin circular plate struck normally at its center by a projectile is studied by an approximate theoretical analysis, FEM simulation and experiment. The plate made of rate sensitive and strain-hardening material undergoes serious local deformation but is not perforated during the impact. The theoretical analysis is based on an energy approach,in which the Cowper-Symonds equation is used for the consideration of strain rate sensitive effects and the parameters involved are determined with the aid of experimental data. The maximum permanent deflections predicted by the theoretical model are compared with those of FEM simulation and published papers obtained both by theory and experiment, and good agreement is achieved for a wide range of thickness of the plates and initial impact velocities.

  12. Mirror deflection control for a confocal scanning laser microscope employing a time-modulated laser and a linear diode array

    Science.gov (United States)

    Aslund, Nils R.; Patwardhan, Ardan; Trepte, Oliver

    1994-04-01

    A mirror deflection device for a CSLM has been developed. It performs repetitive scanning according to a preset waveform which can be chosen arbitrarily. It can also be used to perform stationary positioning at arbitrarily chosen points. A digital memory, comprising dual banks, is used to allow switching from one actuating waveform to another. The movement of the mirror is recorded very accurately. A burst of sequential pulse from a diode laser is deflected by the mirror and recorded by means of a linear diode array. The target pattern is analyzed digitally. The objective is to implement a control strategy whereby a new actuating waveform can be derived in order to correct any deviation between the desired waveform and the recorded one. Some results obtained with the device are reported. Foreseen applications encompass spectral analysis of selected regions and kinetic studies where a trade-off between speed and number of image points is necessary.

  13. From detection to deflection: Mitigation techniques for hidden global threats of natural space objects with short warning time

    Science.gov (United States)

    Hussein, Alaa; Rozenheck, Oshri; Entrena Utrilla, Carlos Manuel

    2016-09-01

    Throughout recorded history, hundreds of Earth impacts have been reported, with some catastrophic localized consequences. Based on the International Space University (ISU) Planetary Defense project named READI, we address the impact event problem by giving recommendations for the development of a planetary defense program. This paper reviews the current detection and tracking techniques and gives a set of recommendations for a better preparation to shield Earth from asteroid and cometary impacts. We also extend the use of current deflection techniques and propose a new compilation of those to deflect medium-sized potentially hazardous objects (PHOs). Using an array of techniques from high-energy lasers to defensive missiles, we present a set of protective layers to defend our planet. The paper focused on threats with a short warning period from discovery to impact with Earth, within few years.

  14. Vibration control in semi-active suspension of the experimental off-road vehicle using information about suspension deflection

    Directory of Open Access Journals (Sweden)

    Kasprzyk Jerzy

    2017-06-01

    Full Text Available The efficiency of vibration control in an automotive semi-active suspension system depends on the quality of information from sensors installed in the vehicle, including information about deflection of the suspension system. The control algorithm for vibration attenuation of the body takes into account its velocity as well as the relative velocity of the suspension. In this paper it is proposed to use the Linear Variable Differential Transformer (LVDT unit to measure the suspension deflection and then to estimate its relative velocity. This approach is compared with a typical solution implemented in such applications, where the relative velocity is calculated by processing signals acquired from accelerometers placed on the body and on the chassis. The experiments performed for an experimental All-Terrain Vehicle (ATV confirm that using LVDT units allows for improving ride comfort by better vibration attenuation of the body.

  15. Deflection and Extraction of Pb Ions up to 33 TeV/c by a Bent Silicon Crystal

    Energy Technology Data Exchange (ETDEWEB)

    Arduini, G.; Biino, C.; Clement, M.; Cornelis, K.; Doble, N.; Elsener, K.; Ferioli, G.; Fidecaro, G.; Gatignon, L.; Grafstroem, P.; Gyr, M.; Herr, W.; Klem, J.; Mikkelsen, U.; Weisse, E. [SL Division, CERN, CH-1211 Geneva 23 (Switzerland); Mo/ller, S.P.; Uggerho/j, E. [ISA, Aarhus University (Denmark); Taratin, A. [JINR, Dubna (Russia); Freund, A. [ESRF, Grenoble (France); Keppler, P.; Major, J. [MPI fuer Metallforschung, Stuttgart (Germany)

    1997-11-01

    The first results from an experiment to deflect a beam of fully stripped, ultrarelativistic Pb{sup 82+} ions of 400 GeV/c per unit of charge, equivalent to 33 TeV/c , by means of a bent crystal are reported. Deflection efficiencies are as high as 14{percent}, in agreement with theoretical estimates. In a second experiment a bent crystal was used to extract 270 GeV/c -per-charge Pb{sup 82+} (22 TeV/c) ions from a coasting beam in the CERN-SPS, and a high extraction efficiency of up to 10{percent} was found. These represent the first measurements to demonstrate applications of bent crystals in high energy heavy ion beams. {copyright} {ital 1997} {ital The American Physical Society}

  16. Deflection and Extraction of Pb Ions up to 33 TeV/c by a Bent Silicon Crystal

    Science.gov (United States)

    Arduini, G.; Biino, C.; Clément, M.; Cornelis, K.; Doble, N.; Elsener, K.; Ferioli, G.; Fidecaro, G.; Gatignon, L.; Grafström, P.; Gyr, M.; Herr, W.; Klem, J.; Mikkelsen, U.; Weisse, E.; Møller, S. P.; Uggerhøj, E.; Taratin, A.; Freund, A.; Keppler, P.; Major, J.

    1997-11-01

    The first results from an experiment to deflect a beam of fully stripped, ultrarelativistic Pb82+ ions of 400 GeV/c per unit of charge, equivalent to 33 TeV/c, by means of a bent crystal are reported. Deflection efficiencies are as high as 14%, in agreement with theoretical estimates. In a second experiment a bent crystal was used to extract 270 GeV/c-per-charge Pb82+ \\(22 TeV/c\\) ions from a coasting beam in the CERN-SPS, and a high extraction efficiency of up to 10% was found. These represent the first measurements to demonstrate applications of bent crystals in high energy heavy ion beams.

  17. Deflection and extraction of Pb ions up to 33 TeV/c by a bent silicon crystal

    CERN Document Server

    Arduini, Gianluigi; Clément, M; Cornelis, Karel; Doble, Niels T; Elsener, K; Ferioli, G; Fidecaro, Giuseppe; Freund, A; Gatignon, L; Grafström, P; Gyr, Marcel; Herr, Werner; Keppler, P; Klem, J T; Major, J V; Mikkelsen, U; Møller, S P; Taratin, A M; Uggerhøj, Erik; Weisse, E

    1997-01-01

    The first results from an experiment to deflect a beam of fully stripped, ulta-relativistic Pb ions of 400 GeV/c per unit of charge, equivalent to 33 TeV/c, by means of a bent crystal are reported. Deflection efficiencies are as high as 14%, in agreement with theoretical predictions. In a second experiment a bent crsytal was used to extract 270 GeV/c per charge Pb82+ (22 TeV/c) ions from a coasting beam in the CERN-SPS, and a high extraction efficiency of up to 10% was found. These represent the first measurements to demonstrate applications of bent crystals in high energy heavy ion beams.

  18. Photothermal spectroscopy of Bacillus anthracis and Bacillus cereus with microcantilevers

    Energy Technology Data Exchange (ETDEWEB)

    Wig, Andrew G [ORNL; Arakawa, Edward T [ORNL; Passian, Ali [ORNL; Ferrell, Thomas L [ORNL; Thundat, Thomas George [ORNL

    2006-03-01

    Microcalorimetric optical and infrared spectroscopy is a method of determining the spectral absorption of small quantities of materials over a wide range of incident wavelengths. In this paper, the first spectroscopic results for microcantilevers coated with Bacillus anthracis (BA) are presented. These results, for B. anthracis from 2.5 to 14.5 {micro}m, are compared with results from microcantilevers coated with Bacillus cereus (BC) and standard spectroscopic absorption data. The results demonstrate strong correlation between the deflection measurements and the reference spectroscopic absorption peaks. An advantage of this microcantilever-based method over traditional spectroscopy is that much smaller amounts of material (nanogram quantities) can be detected in comparison with the milligram amounts needed for standard methods. Another advantage is that the complete system can be relatively small without sacrificing spectral resolution.

  19. Lifetime measurement of excited atomic and ionic states of some noble gases using the high-frequency deflection technique

    Indian Academy of Sciences (India)

    M B Das; S Karmakar

    2005-12-01

    High-frequency deflection (HFD) technique with a delayed coincidence single photon counting arrangement is an efficient technique for radiative lifetime measurement. An apparatus for measurement of the radiative lifetime of atoms and molecules has been developed in our laboratory and measurements have been performed with great success in a large number of atoms and ions. The present version of the apparatus is described in this paper together with a brief description of the basic features and performance.

  20. Complete calculations of the perihelion precession of Mercury and the deflection of light by the Sun in General Relativity

    CERN Document Server

    Magnan, Christian

    2007-01-01

    Taking up a method devised by Taylor and Wheeler and collecting pieces of their work we offer a self-contained derivation of the formulae giving both the precession of the orbit of a planet around the Sun and the deflection angle of a light pulse passing near the Sun in the framework of General Relativity. The demonstration uses only elementary algebra without resorting to tensor formalism. No prior knowledge in relativity is needed to follow the presentation.

  1. Rolling mill optimization using an accurate and rapid new model for mill deflection and strip thickness profile

    Science.gov (United States)

    Malik, Arif Sultan

    This work presents improved technology for attaining high-quality rolled metal strip. The new technology is based on an innovative method to model both the static and dynamic characteristics of rolling mill deflection, and it applies equally to both cluster-type and non cluster-type rolling mill configurations. By effectively combining numerical Finite Element Analysis (FEA) with analytical solid mechanics, the devised approach delivers a rapid, accurate, flexible, high-fidelity model useful for optimizing many important rolling parameters. The associated static deflection model enables computation of the thickness profile and corresponding flatness of the rolled strip. Accurate methods of predicting the strip thickness profile and strip flatness are important in rolling mill design, rolling schedule set-up, control of mill flatness actuators, and optimization of ground roll profiles. The corresponding dynamic deflection model enables solution of the standard eigenvalue problem to determine natural frequencies and modes of vibration. The presented method for solving the roll-stack deflection problem offers several important advantages over traditional methods. In particular, it includes continuity of elastic foundations, non-iterative solution when using pre-determined elastic foundation moduli, continuous third-order displacement fields, simple stress-field determination, the ability to calculate dynamic characteristics, and a comparatively faster solution time. Consistent with the most advanced existing methods, the presented method accommodates loading conditions that represent roll crowning, roll bending, roll shifting, and roll crossing mechanisms. Validation of the static model is provided by comparing results and solution time with large-scale, commercial finite element simulations. In addition to examples with the common 4-high vertical stand rolling mill, application of the presented method to the most complex of rolling mill configurations is demonstrated

  2. Simulation and Prototype Design of Variable Step Angle Techniques Based Asteroid Deflection for Future Planetary Mission

    Science.gov (United States)

    Sathiyavel, C.

    2016-07-01

    Asteroids are minor planets, especially those of the inner Solar System. The most desirable asteroids for cross the geo-synchronous orbit are the carbonaceous C-type asteroids that are deemed by the astronomy community to have a planetary protection categorization of unrestricted Earth return. The mass of near earth Asteroids (assuming spherical asteroid) as a function of its diameter varies from 2 m to 10m, the corresponding densities from 1.9/cm3 to 3.8 g/cm3. For example, a 6.5-m diameter asteroid with a density of 2.8 g/cm3 has a mass of order 4,00,000 kg. If this Asteroid falls on earth then the earth will be destroyed at when the equally of inclination angle both of earth and Asteroid. My proposed work is how we can avert this great danger for near feature the above mass of Asteroid. The present work is Simulation and Prototype Design of a Variable Step Angle Techniques Based Asteroid Deflection for future planetary Mission. Proposed method is comparing with previous method that will be very useful to achieving hit the ion velocity to asteroid surface in several direction at static position of Asteroid deviate mission[ADM].The deviate angle α1 to α2 with help of Variable step angle techniques, it is containing Stepper Motor with attach of Ion propulsion module system.VASAT module is locating the top edge on the three axis stabilized Method in ADM.The three axis stabilized method is including the devices are like Gyroscope sensor ,Arduino Microcontroller system and ion propulsion techniques. Arduino Microcontroller system determines the orientation from gyroscope sensor. Then it uses ion Propulsion techniques modules to control the required motion like pitch, yaw and roll attitude of the ADM. The exhaust thrust value is 1500 mN and velocity is 10,000 m/s [from simulation results but experimental output results is small because low quality of Components is used in research lab] .The propulsion techniques also used as a static position of ADM Mission [both

  3. Sparse, reliable, and long-term stable representation of periodic whisker deflections in the mouse barrel cortex.

    Science.gov (United States)

    Mayrhofer, Johannes M; Haiss, Florent; Helmchen, Fritjof; Weber, Bruno

    2015-07-15

    The rodent whisker system is a preferred model for studying plasticity in the somatosensory cortex (barrel cortex). Contrarily, only a small amount of research has been conducted to characterize the stability of neuronal population activity in the barrel cortex. We used the mouse whisker system to address the neuronal basis of stable perception in the somatosensory cortex. Cortical representation of periodic whisker deflections was studied in populations of neurons in supragranular layers over extended time periods (up to 3 months) with long-term two-photon Ca(2+) imaging in anesthetized mice. We found that in most of the neurons (87%), Ca(2+) responses increased sublinearly with increasing number of contralateral whisker deflections. The imaged population of neurons was activated in a stereotypic way over days and for different deflection rates (pulse frequencies). Thus, pulse frequencies are coded by response strength rather than by distinct neuronal sub-populations. A small population of highly responsive neurons (~3%) was sufficient to decode the whisker stimulus. This conserved functional map, led by a small set of highly responsive neurons, might form the foundation of stable sensory percepts. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Simultaneous distribution between the deflection angle and the lateral displacement under the Moliere theory of multiple scattering

    Energy Technology Data Exchange (ETDEWEB)

    Nakatsuka, Takao [Okayama Shoka University, Laboratory of Information Science, Okayama (Japan); Okei, Kazuhide [Kawasaki Medical School, Dept. of Information Sciences, Kurashiki (Japan); Iyono, Atsushi [Okayama university of Science, Dept. of Fundamental Science, Faculty of Science, Okayama (Japan); Bielajew, Alex F. [Univ. of Michigan, Dept. Nuclear Engineering and Radiological Sciences, Ann Arbor, MI (United States)

    2015-12-15

    Simultaneous distribution between the deflection angle and the lateral displacement of fast charged particles traversing through matter is derived by applying numerical inverse Fourier transforms on the Fourier spectral density solved analytically under the Moliere theory of multiple scattering, taking account of ionization loss. Our results show the simultaneous Gaussian distribution at the region of both small deflection angle and lateral displacement, though they show the characteristic contour patterns of probability density specific to the single and the double scatterings at the regions of large deflection angle and/or lateral displacement. The influences of ionization loss on the distribution are also investigated. An exact simultaneous distribution is derived under the fixed energy condition based on a well-known model of screened single scattering, which indicates the limit of validity of the Moliere theory applied to the simultaneous distribution. The simultaneous distribution will be valuable for improving the accuracy and the efficiency of experimental analyses and simulation studies relating to charged particle transports. (orig.)

  5. Computing the Deflection of the Vertical for Improving Aerial Surveys: A Comparison between EGM2008 and ITALGEO05 Estimates

    Science.gov (United States)

    Barzaghi, Riccardo; Carrion, Daniela; Pepe, Massimiliano; Prezioso, Giuseppina

    2016-01-01

    Recent studies on the influence of the anomalous gravity field in GNSS/INS applications have shown that neglecting the impact of the deflection of vertical in aerial surveys induces horizontal and vertical errors in the measurement of an object that is part of the observed scene; these errors can vary from a few tens of centimetres to over one meter. The works reported in the literature refer to vertical deflection values based on global geopotential model estimates. In this paper we compared this approach with the one based on local gravity data and collocation methods. In particular, denoted by ξ and η, the two mutually-perpendicular components of the deflection of the vertical vector (in the north and east directions, respectively), their values were computed by collocation in the framework of the Remove-Compute-Restore technique, applied to the gravity database used for estimating the ITALGEO05 geoid. Following this approach, these values have been computed at different altitudes that are relevant in aerial surveys. The (ξ, η) values were then also estimated using the high degree EGM2008 global geopotential model and compared with those obtained in the previous computation. The analysis of the differences between the two estimates has shown that the (ξ, η) global geopotential model estimate can be reliably used in aerial navigation applications that require the use of sensors connected to a GNSS/INS system only above a given height (e.g., 3000 m in this paper) that must be defined by simulations. PMID:27472333

  6. Computing the Deflection of the Vertical for Improving Aerial Surveys: A Comparison between EGM2008 and ITALGEO05 Estimates

    Directory of Open Access Journals (Sweden)

    Riccardo Barzaghi

    2016-07-01

    Full Text Available Recent studies on the influence of the anomalous gravity field in GNSS/INS applications have shown that neglecting the impact of the deflection of vertical in aerial surveys induces horizontal and vertical errors in the measurement of an object that is part of the observed scene; these errors can vary from a few tens of centimetres to over one meter. The works reported in the literature refer to vertical deflection values based on global geopotential model estimates. In this paper we compared this approach with the one based on local gravity data and collocation methods. In particular, denoted by ξ and η, the two mutually-perpendicular components of the deflection of the vertical vector (in the north and east directions, respectively, their values were computed by collocation in the framework of the Remove-Compute-Restore technique, applied to the gravity database used for estimating the ITALGEO05 geoid. Following this approach, these values have been computed at different altitudes that are relevant in aerial surveys. The (ξ, η values were then also estimated using the high degree EGM2008 global geopotential model and compared with those obtained in the previous computation. The analysis of the differences between the two estimates has shown that the (ξ, η global geopotential model estimate can be reliably used in aerial navigation applications that require the use of sensors connected to a GNSS/INS system only above a given height (e.g., 3000 m in this paper that must be defined by simulations.

  7. On Calculation Methods and Results for Straight Cylindrical Roller Bearing Deflection, Stiffness, and Stress

    Science.gov (United States)

    Krantz, Timothy L.

    2011-01-01

    The purpose of this study was to assess some calculation methods for quantifying the relationships of bearing geometry, material properties, load, deflection, stiffness, and stress. The scope of the work was limited to two-dimensional modeling of straight cylindrical roller bearings. Preparations for studies of dynamic response of bearings with damaged surfaces motivated this work. Studies were selected to exercise and build confidence in the numerical tools. Three calculation methods were used in this work. Two of the methods were numerical solutions of the Hertz contact approach. The third method used was a combined finite element surface integral method. Example calculations were done for a single roller loaded between an inner and outer raceway for code verification. Next, a bearing with 13 rollers and all-steel construction was used as an example to do additional code verification, including an assessment of the leading order of accuracy of the finite element and surface integral method. Results from that study show that the method is at least first-order accurate. Those results also show that the contact grid refinement has a more significant influence on precision as compared to the finite element grid refinement. To explore the influence of material properties, the 13-roller bearing was modeled as made from Nitinol 60, a material with very different properties from steel and showing some potential for bearing applications. The codes were exercised to compare contact areas and stress levels for steel and Nitinol 60 bearings operating at equivalent power density. As a step toward modeling the dynamic response of bearings having surface damage, static analyses were completed to simulate a bearing with a spall or similar damage.

  8. Chinese Digital Zenith Telescope (DZT) used for Astro-geodetic Deflection of the Vertical Determination

    Science.gov (United States)

    Tian, L.; Wang, B.; Wang, Z.; Yin, Z.; Hu, H.; Wang, H.; Han, Y.

    2015-12-01

    Classical optical astrometry can be used to measure and study variations of plumb line. For the earth gravity filed related researches, it is irreplaceable by technologies like GNSS、VLBI、SLR, etc. However, classical astrometric instruments have some major drawback, such as low efficiency, low automation, more operating observers, and individual error in some visual instruments. In 2011, The National Astronomical Observatories of the Chinese Academy of Sciences (NAOC) successfully developed the new digital zenith telescope prototype (DZT-1), which has the ability of highly automatic observation and data processing, even allowing unattended observation by remote control. By utilizing CCD camera as imaging terminal and high-accuracy tiltmeter to replace mercurial plate, observation efficiency of DZT is improved greatly. According to the results of data obtained from test observations, single-observation accuracy of DZT-1 is 0.15-0.3″ and one night observation accuracy up to 0.07-0.08″, which is better than the observation accuracy of classical astrometric instruments. The observations of DZT can be used to obtain the plumb line variations and the vertical deflections, which can be used for carrying out seismic, geodetic and other related geo-scientific researches. Especially the collocated observations with gravimeters and the conjoint analysis of the observation data will be helpful to recognize the anomalous motion and variation of underground mass over time, and maybe provide significant information for estimating the scale of underground anomalous mass. The information is valuable for determining the three key factors of earthquake possibly. Moreover, the project team is carrying out the development of new DZT with better performance and studying the key techniques for new instrument to make DZT play a more significant role in the astronomy and geoscience fields.

  9. The effect of openings on the long term deflection and flexural capacity of laminated veneer lumber (LVL)

    Science.gov (United States)

    Mancini, Matthew L.

    In most residential construction projects, laminated veneer lumber (LVL) beams are used to help support floor systems, and span doorways or garage door openings, amongst other applications. Because of its diverse application, it is not uncommon that openings are drilled through LVL beams to allow for the passage of utilities. This research evaluates the effects these openings have on long term deflection and flexural capacity, and looks to determine if current provisions for openings need to be amended. Two separate tests were conducted to analyze these behaviors. A long term flexural test was completed to determine the relative creep behavior, and an ultimate load test was conducted to determine the failure load under bending. A total of 26 beams (13 total samples) were tested in the long term test, which included beams with 5 different hole patterns loaded to either 50% or 75% of the allowable load set by the manufacturer. Each beam was loaded for over a year, and its midspan deflection and moisture content was monitored periodically. The environmental conditions such as relative humidity and temperature were also carefully monitored to determine if there was a correlation between relative humidity and long term deflection. Seven of the samples from the long term test were used in the ultimate load test, which included a control sample that was loaded to 60% of the predicted ultimate load so that it could continue being used as a control for the long term test. During the ultimate load test the midpsan and quarterspan deflections were recorded using LVDTs, and the total load was monitored via 4 load cells evenly spaced along the sample. This study found that 2" diameter openings placed in the middle third of the beam length and depth do not significantly affect the long term deflection or flexural capacity of LVL beams. However, as the 2" diameter openings are shifted away from the beam centroid, there is an evident decrease in overall performance in terms of

  10. Fundamental High-Speed Limits in Single-Molecule, Single-Cell, and Nanoscale Force Spectroscopies

    Science.gov (United States)

    2016-01-01

    Force spectroscopy is enhancing our understanding of single-biomolecule, single-cell, and nanoscale mechanics. Force spectroscopy postulates the proportionality between the interaction force and the instantaneous probe deflection. By studying the probe dynamics, we demonstrate that the total force acting on the probe has three different components: the interaction, the hydrodynamic, and the inertial. The amplitudes of those components depend on the ratio between the resonant frequency and the frequency at which the data are measured. A force–distance curve provides a faithful measurement of the interaction force between two molecules when the inertial and hydrodynamic components are negligible. Otherwise, force spectroscopy measurements will underestimate the value of unbinding forces. Neglecting the above force components requires the use of frequency ratios in the 50–500 range. These ratios will limit the use of high-speed methods in force spectroscopy. The theory is supported by numerical simulations. PMID:27359243

  11. Paraffin oil thermal diffusivity determination using a photothermal deflection setup with a 2.3{mu}m pump: a first step towards methane detection

    Energy Technology Data Exchange (ETDEWEB)

    Hamdi, A; Yacoubi, N [Equipe de Photothermie de Nabeul 99/UR/13-22, IPEIN, Mrezka-8000 (Tunisia); Rouillard, Y; Vicet, A [Universite de Montpellier II IES-UMR CNRS 5214/Place Eugene Bataillon - cc 067-F-34095 Montpellier cedex 5 (France); Genty, F, E-mail: abdelwaheb_hamdi@yahoo.f

    2010-03-01

    The photothermal deflection technique, also known as 'mirage effect', is a nondestructive method of evaluating thermal properties of solid, liquid or gaseous species. This technique will be used to detect pollutant absorption. As the deflection is stronger in liquids than gases, we will first consider the deflection in paraffin oil. We consider a medium that is heated by a modulated laser diode beam, and we measure the deflection of the probe beam passing through the heated region as a function of the distance between the axes of the beams. After some theoretical considerations and numerical simulations, we present the application of this method to the experimental determination of the thermal diffusivity of a liquid sample in excellent agreement with previously known values.

  12. Observation of high deflection efficiency and narrow energy loss distributions for 450 GeV protons channeled in a bent silicon crystal

    Science.gov (United States)

    Møller, S. P.; Worm, T.; Clément, M.; Doble, N.; Elsener, K.; Gatignon, L.; Grafström, P.; Uggerhøj, E.; Hage-Ali, M.; Siffert, P.

    1994-03-01

    A 450 GeV proton beam has been deflected by various angles from 1 to 11 mrad using planar channeling in a (111) silicon crystal which was mechanically bent to achieve the desired beam deflection. High deflection efficiencies of up to 50% have been measured, in good agreement with present theoretical estimates. It is shown that bent crystals are also a unique tool for measurements of energy loss and straggling of channeled particles, without any influence from random particles: Selecting protons which are deflected by increasing angles corresponds to decreasing the transverse energy at the crystal entrance. With this technique energy loss and straggling was measured for protons channeled in the wide and narrow (111) planes in silicon for the first time.

  13. Chiroptical Spectroscopy

    Science.gov (United States)

    Gurst, Jerome E.

    1995-09-01

    A brief review of the literature, and Chemical and Engineering News in particular, reveals that the determination and use of optical activity is of increasing importance in today's commercial and research laboratories. The classical technique is to measure [alpha]D using a manual or recording polarimeter to provide a single value, the specific rotation at 589 nm. A spectropolarimeter can be used to determine optical activity through the UV-Visible spectrum (Optical Rotatory Dispersion [ORD]). At wavelengths far removed from electronic absorption bands, optical activity arises from circular birefringence, or the difference in the refractive index for left- and right-circularly polarized light; i.e., nL - nR does not equal zero for chiral materials. If the optical activity is measured through an absorption band, complex behavior is observed (a Cotton Effect curve). At an absorption band, chiral materials exhibit circular dichroism (CD), or a difference in the absorption of left- and right-circularly polarized light; epsilon L minus epsilon R does not equal zero. If the spectropolarimeter is set for the measurement of CD spectra, one observes what appears to be a UV-Vis spectrum except that some absorption bands are positive while others may be negative. Just as enantiomers have specific rotations that are equal and opposite at 589 nm (sodium D line), rotations are equal and opposite at all wavelengths, and CD measurements are equal and opposite at all wavelengths. Figure 1 shows the ORD curves for the enantiomeric carvones while Figure 2 contains the CD curves. The enantiomer of carvone that has the positive [alpha]D is obtained from caraway seeds and is known to have the S-configuration while the R-enantiomer is found in spearmint oil. Figure 1. ORD of S-(+)- and R-(-)-carvones Figure 2. CD of S-(+)- and R-(-)-carvones While little can be done to correlate stereochemistry with [alpha]D values, chiroptical spectroscopy (ORD and/or CD) often can be used to assign

  14. Deflection of 200 GeV/c and 450 GeV/c positively charged particles in a bent germanium crystal

    Science.gov (United States)

    Biino, C.; Clement, M.; Doble, N.; Elsener, K.; Freund, A.; Gatignon, L.; Grafström, P.; Kirsebom, K.; Mikkelsen, U.; Møller, S. P.; Uggerhøj, E.; Worm, T.

    1997-02-01

    Experimental results on high-energy beam deflection by means of a bent germanium crystal are presented. Record deflection efficiencies of 60% have been found for 450 GeV/c protons at small angles. The results obtained with 200 and 450 GeV/c positively charged particles are well described by a classical model, giving confidence in predictions for other crystals and different beam momenta.

  15. Deflection of 200 GeV/c and 450 GeV/c Positively Charged Particles in a Bent Germanium Crystal

    CERN Document Server

    Biino, C; Doble, Niels T; Elsener, K; Freund, A; Gatignon, L; Grafström, P; Kirsebom, K; Mikkelsen, U; Møller, S P; Uggerhøj, Erik; Worm, T

    1997-01-01

    Experimental results on high-energy beam deflection by means of a bent germanium crystal are presented. Record deflection efficiencies of 60% have been found for 450 GeV/c protons at small angles. The results obtained with 200 and 450 GeV/c positively charged particles are well described by a classical model, giving confidence in predictions for other crystals and different beam momenta.

  16. Enhanced Gravity Tractor Derived from the Asteroid Redirect Mission for Deflecting Hypothetical Asteroid 2017 PDC

    Science.gov (United States)

    Mazanek, Daniel D.; Reeves, David M.; Abell, Paul A.; Shen, Haijun; Qu, Min

    2017-01-01

    The Asteroid Redirect Mission (ARM) concept would robotically visit a hazardous-size near-Earth asteroid (NEA) with a rendezvous spacecraft, collect a multi-ton boulder and regolith samples from its surface, demonstrate an innovative planetary defense technique known as the Enhanced Gravity Tractor (EGT), and return the asteroidal material to a stable orbit around the Moon, allowing astronauts to explore the returned material in the mid-2020s. Launch of the robotic vehicle to rendezvous with the ARM reference target, NEA (341843) 2008 EV5, would occur in late 2021 [1,2]. The robotic segment of the ARM concept uses a 40 kW Solar Electric Propulsion (SEP) system with a specific impulse (Isp) of 2600 s, and would provide the first ever demonstration of the EGT technique on a hazardous-size asteroid and validate one method of collecting mass in-situ. The power, propellant, and thrust capability of the ARM robotic spacecraft can be scaled from a 40 kW system to 150 kW and 300 kW, which represent a likely future power level progression. The gravity tractor technique uses the gravitational attraction of a station-keeping spacecraft with the asteroid to provide a velocity change and gradually alter the trajectory of the asteroid. EGT utilizes a spacecraft with a high-efficiency propulsion system, such as Solar Electric Propulsion (SEP), along with mass collected in-situ to augment the mass of the spacecraft, thereby increasing the gravitational force between the objects [3]. As long as the spacecraft has sufficient thrust and propellant capability, the EGT force is only limited by the amount of in-situ mass collected and can be increased several orders of magnitude compared to the traditional gravity tractor technique in which only the spacecraft mass is used to generate the gravitational attraction force. This increase in available force greatly reduces the required deflection time. The collected material can be a single boulder, multiple boulders, regolith, or a

  17. Pull-in analysis of non-uniform microcantilever beams under large deflection

    Science.gov (United States)

    Singh, Sajal Sagar; Pal, Prem; Pandey, Ashok Kumar

    2015-11-01

    Cantilever beams under the influence of electrostatic force form an important subclass of microelectromechanical system (MEMS) and nanoelectromechanical system. Most of the studies concerning these micro-nano resonators are centered around uniform cantilever beams. In this paper, we have investigated another class of micro-resonators consisting of non-uniform cantilever beams. The study is focused around investigating pull-in voltage and resonance frequency of non-uniform cantilever beams when they operate in the linear regime about different static equilibriums. In this paper, we term this frequency as "linear frequency." Calculation of the linear frequency is done at different static equilibriums corresponding to different DC voltages. We have studied two classes of beams, one with increasing cross sectional area from the clamped edge (diverging beam) and other with decreasing cross sectional area from the clamped edge (converging beam). Within each class, we have investigated beams with linear as well as quartic variation in width. We start by obtaining Euler beam equation for non-uniform cantilever beams considering large deflection and their corresponding exact mode shapes from the linear equation. Subsequently, using the Galerkin method based on single mode approximation, we obtain static and dynamic modal equations for finding pull-in voltage and resonance frequency as a function of DC voltage, respectively. We found that the linear frequency of converging beams increases with increase in non-uniform parameter (α) while those of diverging beams decreases with α. A similar trend is observed for pull-in voltage. Within the converging class, beams with quartic variation in width show significant increase in both frequency and pull-in voltage as compared to corresponding linearly tapered beams. In quantitative terms, converging beams with quartic variation in width and α=-0.6 showed an increase in linear frequency by a factor of 2.5 times and pull-in voltage

  18. Solar Sailing Kinetic Energy Interceptor (KEI) Mission for Impacting/Deflecting Near-Earth Asteroids

    Science.gov (United States)

    Wie, Bong

    2005-01-01

    A solar sailing mission architecture, which requires a t least ten 160-m, 300-kg solar sail spacecraft with a characteristic acceleration of 0.5 mm/sqs, is proposed as a realistic near- term option for mitigating the threat posed by near-Earth asteroids (NEAs). Its mission feasibility is demonstrated for a fictional asteroid mitigation problem created by AIAA. This problem assumes that a 200-m asteroid, designated 2004WR, was detected on July 4, 2004, and that the expected impact will occur on January 14, 2015. The solar sailing phase of the proposed mission for the AIAA asteroid mitigation problem is comprised of the initial cruise phase from 1 AU t o 0.25 AU (1.5 years), the cranking orbit phase (3.5 years), and the retrograde orbit phase (1 year) prior to impacting the target asteroid at its perihelion (0.75 AU from the sun) on January 1, 2012. The proposed mission will require at least ten kinetic energy interceptor (KEI) solar sail spacecraft. Each KEI sailcraft consists of a 160- m, 150-kg solar sail and a 150-kg microsatellite impactor. The impactor is to be separated from a large solar sail prior to impacting the 200-m target asteroid at its perihelion. Each 150-kg microsatellite impactor, with a relative impact velocity of at least 70 km/s, will cause a conservatively estimated AV of 0.3 cm/s in the trajectory of the 200-m target asteroid, due largely to the impulsive effect of material ejected from the newly-formed crater. The deflection caused by a single impactor will increase the Earth-miss-distance by 0.45Re (where Re denotes the Earth radius of 6,378 km). Therefore, at least ten KEI sailcraft will be required for consecutive impacts, but probably without causing fragmentation, to increase the total Earth-miss-distance by 4.5Re. This miss-distance increase of 29,000 km is outside of a typical uncertainty/error of about 10,000 km in predicting the Earth-miss- distance. A conventional Delta I1 2925 launch vehicle is capable of injecting at least two KEI

  19. Asteroid Impact Deflection and Assessment (AIDA) mission - Properties of Impact Ejecta

    Science.gov (United States)

    Hamilton, Douglas P.; Fahnestock, Eugene G.; Schwartz, Stephen R.; Murdoch, Naomi; Asphaug, Erik; Cheng, Andrew F.; Housen, Kevin R.; Michel, Patrick; Miller, Paul L.; Stickle, Angela; Tancredi, Gonzalo; Vincent, Jean-Baptiste; Wuennemann, Kai; Yu, Yang; AIDA Impact Simulation Working Group

    2016-10-01

    The Asteroid Impact Deflection and Assessment (AIDA) mission is composed of NASA's Double Asteroid Redirection Test (DART) mission and ESA's Asteroid Impact Monitor (AIM) rendezvous mission. The DART spacecraft is designed to impact the small satellite of near-Earth asteroid 65803 Didymos in October 2022, while the in-situ AIM spacecraft observes. AIDA's Modeling and Simulation of Impact Outcomes Working Group is tasked with investigating properties of the debris ejected from the impact. The orbital evolution of this ejecta has important implications for observations that the AIM spacecraft will take as well as for the safety of the spacecraft itself. Ejecta properties including particle sizes, bulk densities, and velocities all depend on the poorly-known physical properties of Didymos' moon. The moon's density, internal strength, and especially its porosity have a strong effect on all ejecta properties. Making a range of assumptions, we perform a suite of numerical simulations to determine the fate of the ejected material; we will use simulation predictions to optimize AIM observations and safety. Ultimately, combining AIM's observations of the ejecta with detailed numerical simulations will help constrain key satellite parameters.We use distinct types of numerical tools to explore ejecta properties based on additional target parameters (different forms of friction, cohesion), e.g., the shock physics code iSALE, smoothed particle hydrodynamics codes, and the granular code PKDGRAV. Given the large discrepancy between the 6 km/s impact speed of DART and the moon's 6 cm/s escape speed, a great challenge will be to determine properties of the low-speed ejecta. Very low-speed material relevant to the safety of the AIM spacecraft and its ability to conduct its observations may loft from the crater at late stages of the impact process, or from other locations far from the impact site due to seismic energy propagation. The manner in which seismic waves manifests in

  20. Identification of novel vibration- and deflection-sensitive neuronal subgroups in Johnston's organ of the fruit fly.

    Science.gov (United States)

    Matsuo, Eriko; Yamada, Daichi; Ishikawa, Yuki; Asai, Tomonori; Ishimoto, Hiroshi; Kamikouchi, Azusa

    2014-01-01

    The fruit fly Drosophila melanogaster responds behaviorally to sound, gravity, and wind. Johnston's organ (JO) at the antennal base serves as a sensory organ in the fruit fly to detect these mechanosensory stimuli. Among the five anatomically defined subgroups of sensory neurons in JO, subgroups A and B detect sound vibrations and subgroups C and E respond to static deflections, such as gravity and wind. The functions of subgroup-D JO neurons, however, remain unknown. In this study, we used molecular-genetic methods to explore the physiologic properties of subgroup-D JO neurons. Both vibrations and static deflection of the antennal receiver activated subgroup-D JO neurons. This finding clearly revealed that zone D in the antennal mechanosensory and motor center (AMMC), the projection target of subgroup-D JO neurons, is a primary center for antennal vibrations and deflection in the fly brain. We anatomically identified two types of interneurons downstream of subgroup-D JO neurons, AMMC local neurons (AMMC LNs), and AMMC D1 neurons. AMMC LNs are local neurons whose projections are confined within the AMMC, connecting zones B and D. On the other hand, AMMC D1 neurons have both local dendritic arborizations within the AMMC and descending projections to the thoracic ganglia, suggesting that AMMC D1 neurons are likely to relay information of the antennal movement detected by subgroup-D JO neurons from the AMMC directly to the thorax. Together, these findings provide a neural basis for how JO and its brain targets encode information of complex movements of the fruit fly antenna.