defect spectrum presenting: Topics by WorldWideScience.org

Sample records for defect spectrum presenting

Power spectrum analysis for defect screening in integrated circuit devices

Science.gov (United States)

Tangyunyong, Paiboon; Cole Jr., Edward I.; Stein, David J.

2011-12-01

A device sample is screened for defects using its power spectrum in response to a dynamic stimulus. The device sample receives a time-varying electrical signal. The power spectrum of the device sample is measured at one of the pins of the device sample. A defect in the device sample can be identified based on results of comparing the power spectrum with one or more power spectra of the device that have a known defect status.
Localized electromagnetic modes and transmission spectrum of one-dimensional photon crystal with lattice defects

CERN Document Server

Vetrov, S Y

2001-01-01

The properties of the localized electromagnetic modes in the one-dimensional photon crystal with a structural defective layer are studied. The anisotropic layer of the nematic liquid layer is considered as the defect. It is shown that the frequency and coefficient of the defective modes attenuation essentially depend on the defective layer thickness and nematic optical axis orientation. The spectrum of the photon crystal transmittance with one or two defects in the lattice is studied. The possibility of controlling the the photon crystal transmittance spectrum on the count of changing the orientation of the nematic optical axis, for example, through the external electric field is shown with an account of strong anisotropy of the dielectric permittivity
The application of an optical Fourier spectrum analyzer on detecting defects in mass-produced satellite photographs

Science.gov (United States)

Athale, R.; Lee, S. H.

1976-01-01

Various defects in mass-produced pictures transmitted to earth from a satellite are investigated. It is found that the following defects are readily detectable via Fourier spectrum analysis: (1) bit slip, (2) breakup causing loss of image, and (3) disabled track at the top of the imagery. The scratches made on the film during mass production, which are difficult to detect by visual observation, also show themselves readily in Fourier spectrum analysis. A relation is established between the number of scratches, their width and depth and the intensity of their Fourier spectra. Other defects that are found to be equally suitable for Fourier spectrum analysis or visual (image analysis) detection are synchronous loss without blurring of image, and density variation in gray scale. However, the Fourier spectrum analysis is found to be unsuitable for detection of such defects as pin holes, annotation error, synchronous loss with blurring of images, and missing image in the beginning of the work order. The design of an automated, real time system, which will reject defective films, is treated.
Expanding the clinical spectrum associated with defects in CNTNAP2 and NRXN1

Directory of Open Access Journals (Sweden)

Ullmann Reinhard

2011-08-01

Full Text Available Abstract Background Heterozygous copy-number and missense variants in CNTNAP2 and NRXN1 have repeatedly been associated with a wide spectrum of neuropsychiatric disorders such as developmental language and autism spectrum disorders, epilepsy and schizophrenia. Recently, homozygous or compound heterozygous defects in either gene were reported as causative for severe intellectual disability. Methods 99 patients with severe intellectual disability and resemblance to Pitt-Hopkins syndrome and/or suspected recessive inheritance were screened for mutations in CNTNAP2 and NRXN1. Molecular karyotyping was performed in 45 patients. In 8 further patients with variable intellectual disability and heterozygous deletions in either CNTNAP2 or NRXN1, the remaining allele was sequenced. Results By molecular karyotyping and mutational screening of CNTNAP2 and NRXN1 in a group of severely intellectually disabled patients we identified a heterozygous deletion in NRXN1 in one patient and heterozygous splice-site, frameshift and stop mutations in CNTNAP2 in four patients, respectively. Neither in these patients nor in eight further patients with heterozygous deletions within NRXN1 or CNTNAP2 we could identify a defect on the second allele. One deletion in NRXN1 and one deletion in CNTNAP2 occurred de novo, in another family the deletion was also identified in the mother who had learning difficulties, and in all other tested families one parent was shown to be healthy carrier of the respective deletion or mutation. Conclusions We report on patients with heterozygous defects in CNTNAP2 or NRXN1 associated with severe intellectual disability, which has only been reported for recessive defects before. These results expand the spectrum of phenotypic severity in patients with heterozygous defects in either gene. The large variability between severely affected patients and mildly affected or asymptomatic carrier parents might suggest the presence of a second hit, not
A fetus with hemifacial microsomia and sirenomelia. The same mesodermal defect spectrum?

Science.gov (United States)

López-Valdez, Jaime Asael; Estrada-Juárez, Higinio; Moreno-Verduzco, Elsa Romelia; Aguinaga-Ríos, Mónica

2013-04-01

Sirenomelia is the most severe malformation complex affecting the human caudal pole, although its etiology is unclear, a primary defect of blastogenesis has been proposed. Studies consider sirenomelia as the most severe form of caudal dysgenesis, VACTERL association, or axial mesodermal dysplasia, although others still support the idea of a different pathologic entity. We report the prenatal, clinical, and pathologic features of a fetus with cleft lip and palate, microtia, cardiac, renal and intestinal malformations, radial aplasia, and sirenomelia. Karyotype, chromosomal breakage studies, and SHH sequence analysis were normal. The occurrence of cephalic, midline-paramedial, and caudal malformations in the same patient imply the diagnosis of hemifacial microsomia and sirenomelia. These entities are part of the same mesodermal malformation spectrum and the clinical presentation depends on environmental and genetic interactions in embrionic development. Future clinical and genome wide studies will help to better delineate this spectrum.
Defect-detection algorithm for noncontact acoustic inspection using spectrum entropy

Science.gov (United States)

Sugimoto, Kazuko; Akamatsu, Ryo; Sugimoto, Tsuneyoshi; Utagawa, Noriyuki; Kuroda, Chitose; Katakura, Kageyoshi

2015-07-01

In recent years, the detachment of concrete from bridges or tunnels and the degradation of concrete structures have become serious social problems. The importance of inspection, repair, and updating is recognized in measures against degradation. We have so far studied the noncontact acoustic inspection method using airborne sound and the laser Doppler vibrometer. In this method, depending on the surface state (reflectance, dirt, etc.), the quantity of the light of the returning laser decreases and optical noise resulting from the leakage of light reception arises. Some influencing factors are the stability of the output of the laser Doppler vibrometer, the low reflective characteristic of the measurement surface, the diffused reflection characteristic, measurement distance, and laser irradiation angle. If defect detection depends only on the vibration energy ratio since the frequency characteristic of the optical noise resembles white noise, the detection of optical noise resulting from the leakage of light reception may indicate a defective part. Therefore, in this work, the combination of the vibrational energy ratio and spectrum entropy is used to judge whether a measured point is healthy or defective or an abnormal measurement point. An algorithm that enables more vivid detection of a defective part is proposed. When our technique was applied in an experiment with real concrete structures, the defective part could be extracted more vividly and the validity of our proposed algorithm was confirmed.
Fetal Alcohol Spectrum Disorder (FASD) Associated Neural Defects: Complex Mechanisms and Potential Therapeutic Targets.

Science.gov (United States)

Muralidharan, Pooja; Sarmah, Swapnalee; Zhou, Feng C; Marrs, James A

2013-06-19

Fetal alcohol spectrum disorder (FASD), caused by prenatal alcohol exposure, can result in craniofacial dysmorphism, cognitive impairment, sensory and motor disabilities among other defects. FASD incidences are as high as 2% to 5 % children born in the US, and prevalence is higher in low socioeconomic populations. Despite various mechanisms being proposed to explain the etiology of FASD, the molecular targets of ethanol toxicity during development are unknown. Proposed mechanisms include cell death, cell signaling defects and gene expression changes. More recently, the involvement of several other molecular pathways was explored, including non-coding RNA, epigenetic changes and specific vitamin deficiencies. These various pathways may interact, producing a wide spectrum of consequences. Detailed understanding of these various pathways and their interactions will facilitate the therapeutic target identification, leading to new clinical intervention, which may reduce the incidence and severity of these highly prevalent preventable birth defects. This review discusses manifestations of alcohol exposure on the developing central nervous system, including the neural crest cells and sensory neural placodes, focusing on molecular neurodevelopmental pathways as possible therapeutic targets for prevention or protection.
Fetal Alcohol Spectrum Disorder (FASD Associated Neural Defects: Complex Mechanisms and Potential Therapeutic Targets

Directory of Open Access Journals (Sweden)

James A. Marrs

2013-06-01

Full Text Available Fetal alcohol spectrum disorder (FASD, caused by prenatal alcohol exposure, can result in craniofacial dysmorphism, cognitive impairment, sensory and motor disabilities among other defects. FASD incidences are as high as 2% to 5 % children born in the US, and prevalence is higher in low socioeconomic populations. Despite various mechanisms being proposed to explain the etiology of FASD, the molecular targets of ethanol toxicity during development are unknown. Proposed mechanisms include cell death, cell signaling defects and gene expression changes. More recently, the involvement of several other molecular pathways was explored, including non-coding RNA, epigenetic changes and specific vitamin deficiencies. These various pathways may interact, producing a wide spectrum of consequences. Detailed understanding of these various pathways and their interactions will facilitate the therapeutic target identification, leading to new clinical intervention, which may reduce the incidence and severity of these highly prevalent preventable birth defects. This review discusses manifestations of alcohol exposure on the developing central nervous system, including the neural crest cells and sensory neural placodes, focusing on molecular neurodevelopmental pathways as possible therapeutic targets for prevention or protection.
Successful conservative management of symptomatic bilateral dorsal patellar defects presenting with cartilage involvement and bone marrow edema: MRI findings.

Science.gov (United States)

Kwee, Thomas C; Sonneveld, Heleen; Nix, Maarten

2016-05-01

The dorsal patellar defect is a relatively rare entity that involves the superolateral quadrant of the patella. It is usually considered to represent a delayed ossification process, although its exact origin remains unclear. Because of its usually innocuous nature and clinical course, invasive interventions are generally deemed unnecessary, although curretage has been successfully performed on symptomatic cases. This case report presents a rather unusual case of symptomatic bilateral dorsal patellar defects with cartilage involvement and widespread surrounding bone marrow edema as demonstrated by magnetic resonance imaging (MRI). Both cartilage involvement and bone marrow edema should be considered part of the spectrum of associated MRI findings that can be encountered in this entity. Furthermore, the presented case shows that symptomatic dorsal patellar defects can be treated conservatively with success and that (decrease of) pain symptoms are likely related to (decrease of) bone marrow edema.
Extended defect related energy loss in CVD diamond revealed by spectrum imaging in a dedicated STEM

International Nuclear Information System (INIS)

Bangert, U.; Harvey, A.J.; Schreck, M.; Hoermann, F.

2005-01-01

This article aims at investigations of the low EEL region in the wide band gap system diamond. The advent of the UHV Enfina electron energy loss spectrometer combined with Digital Micrograph acquisition and processing software has made reliable detection of absorption losses below 10 eV possible. Incorporated into a dedicated STEM this instrumentation allows the acquisition of spectral information via spectrum maps (spectrum imaging) of sample areas hundreds of nanometers across, with nanometers pixel sizes, adequate spectrum statistics and 0.3 eV energy resolution, in direct correlation with microstructural features in the mapping area. We aim at discerning defect related losses at band gap energies, and discuss different routes to simultaneously process and analyse the spectra in a map. This involves extracting the zero loss peak from each spectrum and constructing ratio maps from the intensities in two energy windows, one defect related and one at a higher, crystal bandstructure dominated energy. This was applied to the residual spectrum maps and their first derivatives. Secondly, guided by theoretical EEL spectra calculations, the low loss spectra were fitted by a series of gaussian distributions. Pixel maps were constructed from amplitude ratios of gaussians, situated in the defect and the unaffected energy regime. The results demonstrate the existence of sp 2 -bonded carbon in the vicinity of stacking faults and partial dislocations in CVD diamond as well as additional states below conduction band, tailing deep into the band gap, at a node in a perfect dislocation. Calculated EEL spectra of shuffle dislocations give similar absorption features at 5-8 eV, and it is thought that this common feature is due to sp 2 -type bonding
Successful conservative management of symptomatic bilateral dorsal patellar defects presenting with cartilage involvement and bone marrow edema: MRI findings

International Nuclear Information System (INIS)

Kwee, Thomas C.; Sonneveld, Heleen; Nix, Maarten

2016-01-01

The dorsal patellar defect is a relatively rare entity that involves the superolateral quadrant of the patella. It is usually considered to represent a delayed ossification process, although its exact origin remains unclear. Because of its usually innocuous nature and clinical course, invasive interventions are generally deemed unnecessary, although curretage has been successfully performed on symptomatic cases. This case report presents a rather unusual case of symptomatic bilateral dorsal patellar defects with cartilage involvement and widespread surrounding bone marrow edema as demonstrated by magnetic resonance imaging (MRI). Both cartilage involvement and bone marrow edema should be considered part of the spectrum of associated MRI findings that can be encountered in this entity. Furthermore, the presented case shows that symptomatic dorsal patellar defects can be treated conservatively with success and that (decrease of) pain symptoms are likely related to (decrease of) bone marrow edema. (orig.)
Successful conservative management of symptomatic bilateral dorsal patellar defects presenting with cartilage involvement and bone marrow edema: MRI findings

Energy Technology Data Exchange (ETDEWEB)

Kwee, Thomas C. [University Medical Center Utrecht, Department of Radiology and Nuclear Medicine, Utrecht (Netherlands); Meander Medical Center, Department of Radiology, Amersfoort (Netherlands); Sonneveld, Heleen [Meander Medical Center, Department of Orthopaedics, Amersfoort (Netherlands); Nix, Maarten [Meander Medical Center, Department of Radiology, Amersfoort (Netherlands)

2016-05-15

The dorsal patellar defect is a relatively rare entity that involves the superolateral quadrant of the patella. It is usually considered to represent a delayed ossification process, although its exact origin remains unclear. Because of its usually innocuous nature and clinical course, invasive interventions are generally deemed unnecessary, although curretage has been successfully performed on symptomatic cases. This case report presents a rather unusual case of symptomatic bilateral dorsal patellar defects with cartilage involvement and widespread surrounding bone marrow edema as demonstrated by magnetic resonance imaging (MRI). Both cartilage involvement and bone marrow edema should be considered part of the spectrum of associated MRI findings that can be encountered in this entity. Furthermore, the presented case shows that symptomatic dorsal patellar defects can be treated conservatively with success and that (decrease of) pain symptoms are likely related to (decrease of) bone marrow edema. (orig.)
Di-interstitial defect in silicon revisited

International Nuclear Information System (INIS)

Londos, C. A.; Antonaras, G.; Chroneos, A.

2013-01-01

Infrared spectroscopy was used to study the defect spectrum of Cz-Si samples following fast neutron irradiation. We mainly focus on the band at 533 cm −1 , which disappears from the spectra at ∼170 °C, exhibiting similar thermal stability with the Si-P6 electron paramagnetic resonance (EPR) spectrum previously correlated with the di-interstitial defect. The suggested structural model of this defect comprises of two self-interstitial atoms located symmetrically around a lattice site Si atom. The band anneals out following a first-order kinetics with an activation energy of 0.88 ± 0.3 eV. This value does not deviate considerably from previously quoted experimental and theoretical values for the di-interstitial defect. The present results indicate that the 533 cm −1 IR band originates from the same structure as that of the Si-P6 EPR spectrum
Synaptic proteins and receptors defects in autism spectrum disorders

Directory of Open Access Journals (Sweden)

Jianling eChen

2014-09-01

Full Text Available Recent studies have found that hundreds of genetic variants, including common and rare variants, rare and de novo mutations, and common polymorphisms have contributed to the occurrence of autism spectrum disorders (ASDs. The mutations in a number of genes such as neurexin, neuroligin, postsynaptic density protein 95 (PSD-95, SH3 and multiple ankyrin repeat domains 3 (SHANK3, synapsin, gephyrin, cadherin (CDH and protocadherin (PCDH, thousand-and-one-amino acid 2 kinase (TAOK2, and contactin (CNTN, have been shown to play important roles in the development and function of synapses. In addition, synaptic receptors, such as gamma-aminobutyric acid (GABA receptors and glutamate receptors, have also been associated with ASDs. This review will primarily focus on the defects of synaptic proteins and receptors associated with ASDs and their roles in the pathogenesis of ASDs via synaptic pathways.
Electrical fingerprint of pipeline defects

International Nuclear Information System (INIS)

Mica, Isabella; Polignano, Maria Luisa; Marco, Cinzia De

2004-01-01

Pipeline defects are dislocations that connect the source region of the transistor with the drain region. They were widely reported to occur in CMOS, BiCMOS devices and recently in SOI technologies. They can reduce device yield either by affecting the devices functionality or by increasing the current consumption under stand-by conditions. In this work the electrical fingerprint of these dislocations is studied, its purpose is to enable us to identify these defects as the ones responsible for device failure. It is shown that the pipeline defects are responsible for a leakage current from source to drain in the transistors. This leakage has a resistive characteristic and it is lightly modulated by the body bias. It is not sensitive to temperature; vice versa the off-current of a good transistor exhibits the well-known exponential dependence on 1/T. The emission spectrum of these defects was studied and compared with the spectrum of a good transistor. The paper aims to show that the spectrum of a defective transistor is quite peculiar; it shows well defined peaks, whereas the spectrum of a good transistor under saturation conditions is characterized by a broad spectral light emission distribution. Finally the deep-level transient spectroscopy (DLTS) is tried on defective diodes
Betaine supplementation reduces congenital defects after prenatal alcohol exposure (Conference Presentation)

Science.gov (United States)

Karunamuni, Ganga; Gu, Shi; Doughman, Yong Qiu; Sheehan, Megan M.; Ma, Pei; Peterson, Lindsy M.; Linask, Kersti K.; Jenkins, Michael W.; Rollins, Andrew M.; Watanabe, Michiko

2016-03-01

Over 500,000 women per year in the United States drink during pregnancy, and 1 in 5 of this population also binge drink. As high as 20-50% of live-born children with prenatal alcohol exposure (PAE) present with congenital heart defects including outflow and valvuloseptal anomalies that can be life-threatening. Previously we established a model of PAE (modeling a single binge drinking episode) in the avian embryo and used optical coherence tomography (OCT) imaging to assay early-stage cardiac function/structure and late-stage cardiac defects. At early stages, alcohol/ethanol-exposed embryos had smaller cardiac cushions and increased retrograde flow. At late stages, they presented with gross morphological defects in the head and chest wall, and also exhibited smaller or abnormal atrio-ventricular (AV) valves, thinner interventricular septae (IVS), and smaller vessel diameters for the aortic trunk branches. In other animal models, the methyl donor betaine (found naturally in many foods such as wheat bran, quinoa, beets and spinach) ameliorates neurobehavioral deficits associated with PAE but the effects on heart structure are unknown. In our model of PAE, betaine supplementation led to a reduction in gross structural defects and appeared to protect against certain types of cardiac defects such as ventricular septal defects and abnormal AV valvular morphology. Furthermore, vessel diameters, IVS thicknesses and mural AV leaflet volumes were normalized while the septal AV leaflet volume was increased. These findings highlight the importance of betaine and potentially methylation levels in the prevention of PAE-related birth defects which could have significant implications for public health.
Prevention of congenital defects induced by prenatal alcohol exposure (Conference Presentation)

Science.gov (United States)

Sheehan, Megan M.; Karunamuni, Ganga; Pedersen, Cameron J.; Gu, Shi; Doughman, Yong Qiu; Jenkins, Michael W.; Watanabe, Michiko; Rollins, Andrew M.

2017-02-01

Over 500,000 women per year in the United States drink during pregnancy, and 1 in 5 of this population also binge drink. Up to 40% of live-born children with prenatal alcohol exposure (PAE) present with congenital heart defects (CHDs) including life-threatening outflow and valvuloseptal anomalies. Previously we established a PAE model in the avian embryo and used optical coherence tomography (OCT) imaging to assay looping-stage (early) cardiac function/structure and septation-stage (late) cardiac defects. Early-stage ethanol-exposed embryos had smaller cardiac cushions (valve precursors) and increased retrograde flow, while late-stage embryos presented with gross head/body defects, and exhibited smaller atrio-ventricular (AV) valves, interventricular septae, and aortic vessels. However, supplementation with the methyl donor betaine reduced gross defects, prevented cardiac defects such as ventricular septal defects and abnormal AV valves, and normalized cardiac parameters. Immunofluorescent staining for 5-methylcytosine in transverse embryo sections also revealed that DNA methylation levels were reduced by ethanol but normalized by co-administration of betaine. Furthermore, supplementation with folate, another methyl donor, in the PAE model appeared to normalize retrograde flow levels which are typically elevated by ethanol exposure. Studies are underway to correlate retrograde flow numbers for folate with associated cushion volumes. Finally, preliminary findings have revealed that glutathione, a key endogenous antioxidant which also regulates methyl group donation, is particularly effective in improving alcohol-impacted survival and gross defect rates. Current investigations will determine whether glutathione has any positive effect on PAE-related CHDs. Our studies could have significant implications for public health, especially related to prenatal nutrition recommendations.
Prevention of congenital defects induced by prenatal alcohol exposure (Conference Presentation)

Science.gov (United States)

Sheehan, Megan M.; Karunamuni, Ganga; Pedersen, Cameron J.; Gu, Shi; Doughman, Yong Qiu; Jenkins, Michael W.; Watanabe, Michiko; Rollins, Andrew M.

2017-02-01

Nearly 2 million women in the United States alone are at risk for an alcohol-exposed pregnancy, including more than 600,000 who binge drink. Even low levels of prenatal alcohol exposure (PAE) can lead to a variety of birth defects, including craniofacial and neurodevelopmental defects, as well as increased risk of miscarriages and stillbirths. Studies have also shown an interaction between drinking while pregnant and an increase in congenital heart defects (CHD), including atrioventricular septal defects and other malformations. We have previously established a quail model of PAE, modeling a single binge drinking episode in the third week of a woman's pregnancy. Using optical coherence tomography (OCT), we quantified intraventricular septum thickness, great vessel diameters, and atrioventricular valve volumes. Early-stage ethanol-exposed embryos had smaller cardiac cushions (valve precursors) and increased retrograde flow, while late-stage embryos presented with gross head/body defects, and exhibited smaller atrio-ventricular (AV) valves, interventricular septum, and aortic vessels. We previously showed that supplementation with the methyl donor betaine reduced gross defects, improved survival rates, and prevented cardiac defects. Here we show that these preventative effects are also observed with folate (another methyl donor) supplementation. Folate also appears to normalize retrograde flow levels which are elevated by ethanol exposure. Finally, preliminary findings have shown that glutathione, a crucial antioxidant, is noticeably effective at improving survival rates and minimizing gross defects in ethanol-exposed embryos. Current investigations will examine the impact of glutathione supplementation on PAE-related CHDs.
Spectrum of clinical presentations in familial hemophagocytic lymphohistiocytosis type 5 patients with mutations in STXBP2

DEFF Research Database (Denmark)

Meeths, Marie; Entesarian, Miriam; Al-Herz, Waleed

2010-01-01

Hemophagocytic lymphohistiocytosis (HLH) is an often-fatal hyperinflammatory syndrome characterized by fever, hepatosplenomegaly, cytopenia, and in some cases hemophagocytosis. Here, we describe the mutation analysis, clinical presentation, and functional analysis of natural killer (NK) cells...... (FHL), the clinical findings included colitis, bleeding disorders, and hypogammaglobulinemia in approximately one-third of the patients. Laboratory analysis revealed impairment of NK-cell degranulation and cytotoxic capacity. Interleukin-2 stimulation of lymphocytes in vitro rescued the NK cell......-associated functional defects. In conclusion, familial HLH type 5 is associated with a spectrum of clinical symptoms, which may be a reflection of impaired expression and function of Munc18-2 also in cells other than cytotoxic lymphocytes. Mutations in STXBP2 should thus also be considered in patients with clinical...
Primordial inhomogeneities from massive defects during inflation

Energy Technology Data Exchange (ETDEWEB)

Firouzjahi, Hassan; Karami, Asieh; Rostami, Tahereh, E-mail: firouz@ipm.ir, E-mail: karami@ipm.ir, E-mail: t.rostami@ipm.ir [School of Astronomy, Institute for Research in Fundamental Sciences (IPM), P.O. Box 19395-5531, Tehran (Iran, Islamic Republic of)

2016-10-01

We consider the imprints of local massive defects, such as a black hole or a massive monopole, during inflation. The massive defect breaks the background homogeneity. We consider the limit that the physical Schwarzschild radius of the defect is much smaller than the inflationary Hubble radius so a perturbative analysis is allowed. The inhomogeneities induced in scalar and gravitational wave power spectrum are calculated. We obtain the amplitudes of dipole, quadrupole and octupole anisotropies in curvature perturbation power spectrum and identify the relative configuration of the defect to CMB sphere in which large observable dipole asymmetry can be generated. We observe a curious reflection symmetry in which the configuration where the defect is inside the CMB comoving sphere has the same inhomogeneous variance as its mirror configuration where the defect is outside the CMB sphere.

Defect CFTs and holographic multiverse

International Nuclear Information System (INIS)

Fiol, Bartomeu

2010-01-01

We investigate some aspects of a recent proposal for a holographic description of the multiverse. Specifically, we focus on the implications on the suggested duality of the fluctuations of a bubble separating two universes with different cosmological constants. We do so by considering a similar problem in a 2+1 CFT with a codimension one defect, obtained by an M5-brane probe embedding in AdS 4 × S 7 , and studying its spectrum of fluctuations. Our results suggest that the kind of behavior required by the spectrum of bubble fluctuations is not likely to take place in defect CFTs with an AdS dual, although it might be possible if the defect supports a non-unitary theory
Lectures on cosmic topological defects

Energy Technology Data Exchange (ETDEWEB)

Vachaspati, T [Department of Astronomy and Astrophysics, Colaba, Mumbai (India) and Physics Department, Case Western Reserve University, Cleveland (United States)

2001-11-15

These lectures review certain topological defects and aspects of their cosmology. Unconventional material includes brief descriptions of electroweak defects, the structure of domain walls in non-Abelian theories, and the spectrum of magnetic monopoles in SU(5) Grand Unified theory. (author)
EPR of defects in semiconductors: past, present, future

International Nuclear Information System (INIS)

Watkins, G.D.

1999-01-01

Important physical concepts learned from early EPR studies of defects in silicon are reviewed. Highlighted are the studies of shallow effective-mass-liked donors and acceptors of deep transition element impurities, and of vacancies and interstitials. It is shown that the concepts learned in silicon translate remarkable well to the corresponding defects in the other elemental and compound semiconductors. The introduction of sensitive optical and electrical detection methods and the recent progress in single defects detection insure the continued vital role of EPR in the future
Defect CFTs and holographic multiverse

Energy Technology Data Exchange (ETDEWEB)

Fiol, Bartomeu, E-mail: bfiol@ub.edu [Departament de Física Fonamental i Institut de Ciències del Cosmos, Universitat de Barcelona, Martí i Franquès 1, 08193 Barcelona (Spain)

2010-07-01

We investigate some aspects of a recent proposal for a holographic description of the multiverse. Specifically, we focus on the implications on the suggested duality of the fluctuations of a bubble separating two universes with different cosmological constants. We do so by considering a similar problem in a 2+1 CFT with a codimension one defect, obtained by an M5-brane probe embedding in AdS{sub 4} × S{sup 7}, and studying its spectrum of fluctuations. Our results suggest that the kind of behavior required by the spectrum of bubble fluctuations is not likely to take place in defect CFTs with an AdS dual, although it might be possible if the defect supports a non-unitary theory.
Study of the influence of the fast neutron spectrum on the production of defects in solids and liquids

International Nuclear Information System (INIS)

Mas, P.; Droulers, Y.

1964-01-01

In the first part of this work a calculation has been made of the number of defects formed in graphite by a given neutron flux having various spectral distributions. The defect formation function is that of KINCHIN and PEASE; its formulation is briefly given. An efficiency function is then defined for a fast neutron spectrum. This defects produced in a light water reactor and those produced in a graphite reactor. Finally an application of this method is given for comparing the defect forming tendency in graphite in the case of the reactor Melusine and of the reactor G-2 and G-3. In the second part are calculated the integrals for the energy release brought about by fast neutrons in carbon oxygen and hydrogen. In a region of 25 cm around the core of a swimming-pool type reactor these energy release integrals are approximately proportional to the neutron flux above 1 MeV. The determination of the energy released as a result of the passage of neutrons in organic liquids can therefore be reduced to the measurement of the flux above 1 MeV for the real spectral distribution. A calorimetric verification has been carried out in the case of water. (authors) [fr
Serine biosynthesis and transport defects.

Science.gov (United States)

El-Hattab, Ayman W

2016-07-01

l-serine is a non-essential amino acid that is biosynthesized via the enzymes phosphoglycerate dehydrogenase (PGDH), phosphoserine aminotransferase (PSAT), and phosphoserine phosphatase (PSP). Besides its role in protein synthesis, l-serine is a potent neurotrophic factor and a precursor of a number of essential compounds including phosphatidylserine, sphingomyelin, glycine, and d-serine. Serine biosynthesis defects result from impairments of PGDH, PSAT, or PSP leading to systemic serine deficiency. Serine biosynthesis defects present in a broad phenotypic spectrum that includes, at the severe end, Neu-Laxova syndrome, a lethal multiple congenital anomaly disease, intermediately, infantile serine biosynthesis defects with severe neurological manifestations and growth deficiency, and at the mild end, the childhood disease with intellectual disability. A serine transport defect resulting from deficiency of the ASCT1, the main transporter for serine in the central nervous system, has been recently described in children with neurological manifestations that overlap with those observed in serine biosynthesis defects. l-serine therapy may be beneficial in preventing or ameliorating symptoms in serine biosynthesis and transport defects, if started before neurological damage occurs. Herein, we review serine metabolism and transport, the clinical, biochemical, and molecular aspects of serine biosynthesis and transport defects, the mechanisms of these diseases, and the potential role of serine therapy. Copyright © 2016 Elsevier Inc. All rights reserved.
Sirenomelia: A Multi-systemic Polytopic Field Defect with Ongoing Controversies.

Science.gov (United States)

Boer, Lucas L; Morava, Eva; Klein, Willemijn M; Schepens-Franke, Annelieke N; Oostra, Roelof Jan

2017-06-01

The most impressive phenotypic appearance of sirenomelia is the presence of a 180°-rotated, axially positioned, single lower limb. Associated gastrointestinal and genitourinary anomalies are almost always present. This rare anomaly is still the subject of ongoing controversies concerning its nosology, pathogenesis, and possible genetic etiology. Sirenomelia can be part of a syndromic continuum, overlapping with other complex conditions including caudal dysgenesis and VATER/VACTERL/VACTERL-H associations, which could all be part of a heterogeneous spectrum, and originate from an early defect in blastogenesis. It is imaginable that different "primary field defects," whether or not genetically based, induce a spectrum of caudal malformations. In the current study, we review the contemporary hypotheses and conceptual approaches regarding the etiology and pathogenesis of sirenomelia, especially in the context of concomitant conditions. To expand on the latter, we included the external and internal dysmorphology of one third trimester sirenomelic fetus from our anatomical museum collection, in which multiple concomitant but discordant anomalies were observed compared with classic sirenomelia, and was diagnosed as VACTERL-H association with sirenomelia. Birth Defects Research 109:791-804, 2017. © 2017 The Authors. Birth Defects Research Published by Wiley Periodicals, Inc. © 2017 The Authors. Birth Defects Research Published by Wiley Periodicals, Inc.
Defect pair formation in fluorine and nitrogen codoped TiO2

Science.gov (United States)

Kordatos, A.; Kelaidis, N.; Chroneos, A.

2018-04-01

Titanium oxide is extensively investigated because of its high chemical stability and its photocatalytic properties; nevertheless, the large band gap limits its activity to a small portion of the solar spectrum. Nitrogen and fluorine codoping is an efficient defect engineering strategy to increase the photocatalytic activity of titanium oxide. In the present study, we apply density functional theory to investigate the interaction of nitrogen with fluorine and the formation of defect pairs. We show that in fluorine and nitrogen codoped titanium oxide, the FiNi, FONi, and FiNTi defects can form. Their impact on the electronic structure of titanium oxide is discussed.
Spectrum of congenital heart defects and extracardiac malformations associated with chromosomal abnormalities: results of a seven year necropsy study

OpenAIRE

Tennstedt, C; Chaoui, R; Korner, H; Dietel, M

1999-01-01

OBJECTIVE—To analyse the spectrum of congenital heart malformations, the frequency of extracardiac malformations, and the proportion of chromosome aberrations among fetuses sent for necropsy. MATERIAL—Necropsies were performed on 815 fetuses—448 induced abortions (55%), 220 spontaneous abortions (27%), and 147 stillbirths (18%)—during a seven year period (1991-97) in the department of pathology of the Charité Medical Centre in Berlin. A congenital heart defect was identified in 129 cases (16%...
Two-Dimensional Impact Reconstruction Method for Rail Defect Inspection

Directory of Open Access Journals (Sweden)

Jie Zhao

2014-01-01

Full Text Available The safety of train operating is seriously menaced by the rail defects, so it is of great significance to inspect rail defects dynamically while the train is operating. This paper presents a two-dimensional impact reconstruction method to realize the on-line inspection of rail defects. The proposed method utilizes preprocessing technology to convert time domain vertical vibration signals acquired by wireless sensor network to space signals. The modern time-frequency analysis method is improved to reconstruct the obtained multisensor information. Then, the image fusion processing technology based on spectrum threshold processing and node color labeling is proposed to reduce the noise, and blank the periodic impact signal caused by rail joints and locomotive running gear. This method can convert the aperiodic impact signals caused by rail defects to partial periodic impact signals, and locate the rail defects. An application indicates that the two-dimensional impact reconstruction method could display the impact caused by rail defects obviously, and is an effective on-line rail defects inspection method.
Fetal alcohol spectrum disorders har fået danske kriterier

DEFF Research Database (Denmark)

Broccia, Marcella; Vikre-Jørgensen, Jennifer; Rausgaard, Nete Lundager Klokker

2017-01-01

The Danish Paediatric Society presents the first Danish definition of fetal alcohol spectrum disorders (FASD) in a new guideline. FASD is an umbrella term for conditions caused by prenatal alcohol exposure. To varying degrees, fetal alcohol damages manifest as physical defects, characteristic fac...
Fetal alcohol spectrum disorders har fået danske kriterier

DEFF Research Database (Denmark)

Broccia, Marcella; Vikre-Jørgensen, Jennifer; Rausgaard, Nete Lundager Klokker

2017-01-01

The Danish Paediatric Society presents the first Danish definition of fetal alcohol spectrum disorders (FASD) in a new guideline. FASD is an umbrella term for conditions caused by prenatal alcohol exposure. To varying degrees, fetal alcohol damages manifest as physical defects, characteristic...
Zellweger Spectrum

Science.gov (United States)

... severe defect, resulting in essentially nonfunctional peroxisomes. This phenomenon produces the range of severity of the disorders. How is the Zellweger Spectrum Diagnosed? The distinctive shape of the head and face of a child born with one of the diseases of the ...
Band gap control in a line-defect magnonic crystal waveguide

Energy Technology Data Exchange (ETDEWEB)

Morozova, M. A., E-mail: mamorozovama@yandex.ru; Grishin, S. V.; Sadovnikov, A. V.; Romanenko, D. V.; Sharaevskii, Yu. P.; Nikitov, S. A. [Laboratory ' Metamaterials,' Saratov State University, Astrakhanskaya 83, Saratov 410012 (Russian Federation)

2015-12-14

We report on the experimental observation of the spin wave spectrum control in a line-defect magnonic crystal (MC) waveguide. We demonstrate the possibility to control the forbidden frequency band (band gap) for spin waves tuning the line-defect width. In particular, this frequency may be greater or lower than the one of 1D MC waveguide without line-defect. By means of space-resolved Brillouin light scattering technique, we study the localization of magnetization amplitude in the line-defect area. We show that the length of this localization region depends on the line-defect width. These results agree well with theoretical calculations of spin wave spectrum using the proposed model of two coupled magnonic crystal waveguides. The proposed simple geometry of MC with line-defect can be used as a logic and multiplexing block for application in the novel field of magnonic devices.
Turmeric Extract Rescues Ethanol-Induced Developmental Defect in the Zebrafish Model for Fetal Alcohol Spectrum Disorder (FASD).

Science.gov (United States)

Muralidharan, Pooja; Connors, Craig T; Mohammed, Arooj S; Sarmah, Swapnalee; Marrs, Kathleen; Marrs, James A; Chism, Grady W

2017-09-01

Prenatal ethanol exposure causes the most frequent preventable birth disorder, fetal alcohol spectrum disorder (FASD). The effect of turmeric extracts in rescuing an ethanol-induced developmental defect using zebrafish as a model was determined. Ethanol-induced oxidative stress is one of the major mechanisms underlying FASD. We hypothesize that antioxidant inducing properties of turmeric may alleviate ethanol-induced defects. Curcuminoid content of the turmeric powder extract (5 mg/mL turmeric in ethanol) was determined by UPLC and found to contain Curcumin (124.1 ± 0.2 μg/mL), Desmethoxycurcumin (43.4 ± 0.1 μg/mL), and Bisdemethoxycurcumin (36.6 ± 0.1 μg/mL). Zebrafish embryos were treated with 100 mM (0.6% v/v) ethanol during gastrulation through organogenesis (2 to 48 h postfertilization (hpf)) and supplemented with turmeric extract to obtain total curcuminoid concentrations of 0, 1.16, 1.72, or 2.32 μM. Turmeric supplementation showed significant rescue of the body length at 72 hpf compared to ethanol-treated embryos. The mechanism underlying the rescue remains to be determined. © 2017 Institute of Food Technologists®.
Caudal dysgenesis, sirenomelia, and situs inversus totalis: a primitive defect in blastogenesis.

Science.gov (United States)

Rougemont, Anne-Laure; Bouron-Dal Soglio, Dorothée; Désilets, Valérie; Jovanovic, Mubina; Perreault, Gilles; Laurier Oligny, Luc; Fournet, Jean-Christophe

2008-06-01

Caudal dysgenesis (CD) constitutes a heterogeneous spectrum of congenital caudal anomalies, including varying degrees of agenesis of the vertebral column, as well as anorectal and genitourinary anomalies. Sirenomelia, characterized by a fusion of the lower limbs, could represent the most severe end of this spectrum. The two main debated pathogenic hypotheses are an aberrant vascular supply versus a primary axial mesoderm defect. We present the autopsy findings of two fetuses of non-diabetic mothers, with normal karyotype. Both fetuses presented situs inversus associated with a CD, in one case consisting of sirenomelia, establishing a very rare association profile that might be random. This association also suggests the occurrence of a common pathogenic mechanism, in accordance to recent genetic data, such as displayed in the Kif3A murine mutation phenotype. Some cases of sirenomelia and CD could represent developmental field defects of blastogenesis involving the caudal mesoderm, rather than being related to vascular insufficiency.
Spectrum of PEX6 mutations in Zellweger syndrome spectrum patients

NARCIS (Netherlands)

Ebberink, Merel S.; Kofster, Janet; Wanders, Ronald J. A.; Waterham, Hans R.

2010-01-01

The autosomal recessive Zellweger syndrome spectrum (ZSS) disorders comprise a main subgroup of the peroxisome biogenesis disorders. The ZSS disorders can be caused by mutations in any of 12 different currently identified PEX genes resulting in severe, often lethal, multi-systemic disorders. Defects
Excess of non-verbal cases of autism spectrum disorders presenting ...

African Journals Online (AJOL)

Objectives. Characteristics of children with autism spectrum disorders (ASDs) in Africa are not known because of unavailability of large-scale epidemiological studies in this region. This review explored the age at first presentation to orthodox clinical practice of African children with ASDs and their expressive language ability ...
Conformal structure in the spectrum of an altered quantum Ising chain

International Nuclear Information System (INIS)

Henkel, M.; Patkos, A.

1986-07-01

The Ising model with an infinite line of defects is mapped onto a strip with two defect lines. The Hamiltonian spectrum is studied at the bulk critical point. Its exact diagonal form is found for an infinite number of sites. The spectrum of physical excitations contains an infinite number of primary fields, while the leading ground state energy correction is independent of the defect strength. A novel algebraic structure interpolating between those belonging to periodic and free boundary conditions is signalled. (orig.)
Brief Report: Self-Presentation of Children with Autism Spectrum Disorders

Science.gov (United States)

Begeer, Sander; Banerjee, Robin; Lunenburg, Patty; Terwogt, Mark Meerum; Stegge, Hedy; Rieffe, Carolien

2008-01-01

The self-presentational behaviour of 43 6- to 12-year-old children with high functioning autism spectrum disorders (HFASD) and normal intelligence and 43 matched comparisons was investigated. Children were prompted to describe themselves twice, first in a baseline condition and then in a condition where they were asked to convince others to select…

Congenital defects of C1 arches and odontoid process in a child with Down′s syndrome: A case presentation

Directory of Open Access Journals (Sweden)

Catherine Hatzantonis

2016-01-01

Full Text Available We present the case of a 2-year-old child with Down′s syndrome who presented to our unit with torticollis. Imaging studies revealed the rare occurrence of anterior and posterior C1 arch defects, absent odontoid process, and atlantoaxial subluxation. We managed her conservatively for 3 years without neurological deficits or worsening of atlantoaxial subluxation. We discuss the rare occurrences of anterior and posterior arch defects of the atlas, the radiological presentations of axis defects in patients, and the occurrence of atlantoaxial instability in patients with Down′s syndrome. Management options with consideration to surgery in asymptomatic and symptomatic patients are also discussed.
WMAP constraints on inflationary models with global defects

International Nuclear Information System (INIS)

Bevis, Neil; Hindmarsh, Mark; Kunz, Martin

2004-01-01

We use the cosmic microwave background angular power spectra to place upper limits on the degree to which global defects may have aided cosmic structure formation. We explore this under the inflationary paradigm, but with the addition of textures resulting from the breaking of a global O(4) symmetry during the early stages of the Universe. As a measure of their contribution, we use the fraction of the temperature power spectrum that is attributed to the defects at a multipole of 10. However, we find a parameter degeneracy enabling a fit to the first-year WMAP data to be made even with a significant defect fraction. This degeneracy involves the baryon fraction and the Hubble constant, plus the normalization and tilt of the primordial power spectrum. Hence, constraints on these cosmological parameters are weakened. Combining the WMAP data with a constraint on the physical baryon fraction from big bang nucleosynthesis calculations and high-redshift deuterium abundance limits the extent of the degeneracy and gives an upper bound on the defect fraction of 0.13 (95% confidence)
Vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association with Mayer-Rokitansky-Küster-Hauser syndrome in co-occurrence

DEFF Research Database (Denmark)

Bjørsum-Meyer, Thomas; Herlin, Morten; Qvist, Niels

2016-01-01

Background: The vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association and Mayer-Rokitansky-Küster-Hauser syndrome are rare conditions. We aimed to present two cases with the vertebral defect, anal atresia, cardiac...... defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association and Mayer-Rokitansky-Küster-Hauser co-occurrence from our local surgical center and through a systematic literature search detect published cases. Furthermore, we aimed to collect existing knowledge...... in the embryopathogenesis and genetics in order to discuss a possible link between the vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association and Mayer-Rokitansky-Küster-Hauser syndrome. Case presentation: Our first case was a white girl...
Positron Studies of Defects in Thin Films and Semiconductors

OpenAIRE

Edwardson, C J

2013-01-01

Positron studies of defects in thin films and semiconductors are reviewed. The resultsobtained from experimental studies of Doppler broadening of annihilation radiation (DBAR)from variable energies are presented. Normalisation methods for the DBAR parameters S andW have been developed, allowing for direct comparisons of the results for different samplestaken over long periods of time. The evaluation of the P:V parameter, the peak-to-valley ratioin a full annihilation spectrum, has been improv...
The electronic transport properties of defected bilayer sliding armchair graphene nanoribbons

Science.gov (United States)

Mohammadi, Amin; Haji-Nasiri, Saeed

2018-04-01

By applying non-equilibrium Green's functions (NEGF) in combination with tight-binding (TB) model, we investigate and compare the electronic transport properties of perfect and defected bilayer armchair graphene nanoribbons (BAGNRs) under finite bias. Two typical defects which are placed in the middle of top layer (i.e. single vacancy (SV) and stone wale (SW) defects) are examined. The results reveal that in both perfect and defected bilayers, the maximum current refers to β-AB, AA and α-AB stacking orders, respectively, since the intermolecular interactions are stronger in them. Moreover it is observed that a SV decreases the current in all stacking orders, but the effects of a SW defect is nearly unpredictable. Besides, we introduced a sequential switching behavior and the effects of defects on the switching performance is studied as well. We found that a SW defect can significantly improve the switching behavior of a bilayer system. Transmission spectrum, band structure, molecular energy spectrum and molecular projected self-consistent Hamiltonian (MPSH) are analyzed subsequently to understand the electronic transport properties of these bilayer devices which can be used in developing nano-scale bilayer systems.
Clinical spectrum of rhabdomyolysis presented to pediatric emergency department

Science.gov (United States)

2013-01-01

Background Rhabdomyolysis is a potentially life-threatening syndrome that can develop from a variety of causes. The aim of the work is to analyze the clinical spectrum and to evaluate the prevalence of various etiologies in children, who present to the emergency department (ED) with rhabdomyolysis. Methods During a 6-year study period, we retrospectively analyzed the medical charts of patients, aged 18 years or younger, with a definite diagnosis of rhabdomyolysis and serum creatinine phosphokinase (CK) levels greater than 1000IU/L. We analyzed the clinical spectrum and evaluated the potential risk factors of acute renal failure (ARF). Results Thirty-seven patients (mean age = 10.2 ± 5.5 years), including 26 males and 11 females, were enrolled in the study. Two of the most common presented symptoms in these 37 patients were muscle pain and muscle weakness (83.8% and 73%, respectively). Dark urine was reported in only 5.4% of the patients. The leading cause of rhabdomyolysis in the 0- to 9-year age group was presumed infection, and the leading cause in the 10- to 18-year age group was trauma and exercise. The incidence of ARF associated with rhabdomyolysis was 8.1 % and no child needed for renal replacement therapy (RRT). We did not identify any reliable predictors of ARF or need for RRT. Conclusions The classic triad of symptoms of rhabdomyolysis includes myalgia, weakness and dark urine are not always presented in children. The cause of rhabdomyolysis in younger age is different from that of teenager group. However, the prognosis of rhabdomyolysis was good with appropriate management. PMID:24004920
Teratology: from science to birth defects prevention.

Science.gov (United States)

Rasmussen, Sonja A; Erickson, J David; Reef, Susan E; Ross, Danielle S

2009-01-01

One of the goals of birth defects research is to better understand risk or preventive factors for birth defects so that strategies for prevention can be developed. In this article, we have selected four areas of birth defects research that have led to the development of prevention strategies. These areas include rubella virus as a cause of congenital rubella syndrome, folic acid as a preventive factor for neural tube defects, cytomegalovirus infection as a cause of birth defects and developmental disabilities, and alcohol as a cause of fetal alcohol spectrum disorders. For each of these areas, we review key clinical and research findings that led to the identification of the risk or preventive factor, milestones in the development of prevention strategies, and the progress made thus far toward prevention.
Microstructural defects in EUROFER 97 after different neutron irradiation conditions

Directory of Open Access Journals (Sweden)

Christian Dethloff

2016-12-01

Full Text Available Characterization of irradiation induced microstructural evolution is essential for assessing the applicability of structural steels like the Reduced Activation Ferritic/Martensitic steel EUROFER 97 in upcoming fusion reactors. In this work Transmission Electron Microscopy (TEM is used to determine the defect microstructure after different neutron irradiation conditions. In particular dislocation loops, voids and precipitates are analyzed concerning defect nature, density and size distribution after irradiation to 15 dpa at 300 °C in the mixed spectrum High Flux Reactor (HFR. New results are combined with previously obtained data from irradiation in the fast spectrum BOR-60 reactor (15 and 32 dpa, 330 °C, which allows for assessment of dose and dose rate effects on the aforementioned irradiation induced defects and microstructural characteristics.
Android application and REST server system for quasar spectrum presentation and analysis

Science.gov (United States)

Wasiewicz, P.; Pietralik, K.; Hryniewicz, K.

2017-08-01

This paper describes the implementation of a system consisting of a mobile application and RESTful architecture server intended for the analysis and presentation of quasars' spectrum. It also depicts the quasar's characteristics and significance to the scientific community, the source for acquiring astronomical objects' spectral data, used software solutions as well as presents the aspect of Cloud Computing and various possible deployment configurations.
Autism Spectrum Disorder

Centers for Disease Control (CDC) Podcasts

2014-04-02

This podcast discusses autism spectrum disorder (ASD), a developmental disability that causes problems with social, communication, and behavioral skills. CDC estimates that one in 68 children has been identified as having ASD. Created: 4/2/2014 by National Center on Birth Defects and Developmental Disabilities (NCBDDD). Date Released: 4/2/2014.
Nature of oxygen donors and radiation defects in oxygen-doped germanium

International Nuclear Information System (INIS)

Fukuoka, Noboru; Atobe, Kozo; Honda, Makoto; Matsuda, Koji.

1991-01-01

The nature of oxygen donors and radiation defects in oxygen-doped germanium were studied through measurements of the infrared absorption spectrum, deep level transient spectroscopy spectrum and carrier concentration. It is revealed that a new donor is not formed in oxygen-doped germanium. An A-center (interstitial oxygen-vacancy pair) forms a complex with a thermal donor in its annealing stage at 60degC-140degC. The introduction rate of defects by 1.5 MeV electron irradiation was enhanced in thermal-donor-doped samples. (author)
Tegmen Tympani Defect and Brain Herniation Secondary to Mastoid Surgery: Case Presentation

Directory of Open Access Journals (Sweden)

Oguz Kadir Egilmez

2014-01-01

Full Text Available Brain herniation into the middle ear is very rarely seen. In addition to reasons like congenital factors, trauma, and infection, tegmen defect may develop as a result of iatrogenic events secondary to chronic otitis media surgery with or without cholesteatoma. Since it may cause life-threatening complications, patients must be evaluated and monitored for tegmen defect. In this paper, diagnosis and treatment of a brain herniation case due to iatrogenic tegmen defect were described along with relevant literature.
Congenital heart defects in oculodentodigital dysplasia: Report of two cases.

Science.gov (United States)

Izumi, Kosuke; Lippa, Andrew M; Wilkens, Alisha; Feret, Holly A; McDonald-McGinn, Donna M; Zackai, Elaine H

2013-12-01

Oculodentodigital dysplasia is caused by mutations in the GJA1 gene. Oculodentodigital dysplasia presents with a spectrum of clinical features including craniofacial, ocular, dental, and limb anomalies. Although recent findings implicate the major role of GJA1 during cardiac organogenesis, congenital heart defects are infrequently reported in oculodentodigital dysplasia. Here we report on two patients with GJA1 mutations presenting with cardiac malformations and type III syndactyly. Patient 1 presented with pulmonary atresia, an intact septum, right ventricular hypoplasia and tricuspid stenosis. The infant had a small nose, thin columella and bilateral 4-5 syndactyly of the fingers. A de novo c.226C>T (p.Arg76Cys) mutation was identified. Patient 2 presented at 6 months with a ventricular septal defect. The child had hypoplastic alae nasi with a thin columella and bilateral 4-5 syndactyly of the digits. A de novo missense mutation, c.145C>G (p.Gln49Glu) was found. Our two patients underscore the importance of cardiac evaluations as part of the initial workup for patients with findings of oculodentodigital dysplasia. Conversely, those patients with type III syndactyly and congenital heart defect should be screened for GJA1 mutations. © 2013 Wiley Periodicals, Inc.
Ionization-induced rearrangement of defects in silicon

International Nuclear Information System (INIS)

Vinetskij, V.L.; Manojlo, M.A.; Matvijchuk, A.S.; Strikha, V.I.; Kholodar', G.A.

1988-01-01

Ionizing factor effect on defect rearrangement in silicon including centers with deep local electron levels in the p-n-transition region is considered. Deep center parameters were determined using non-steady-state capacity spectroscopy of deep levels (NCDLS) method. NCDLS spectrum measurement was performed using source p + -n - diodes and after their irradiation with 15 keV energy electrons or laser pulses. It is ascertained that in silicon samples containing point defect clusters defect rearrangement under ionizing factor effect takes place, i.e. deep level spectra are changed. This mechanism is efficient in case of silicon irradiation with subthreshold energy photons and electrons and can cause degradation of silicon semiconducting structures
Nelson′s syndrome presenting as bilateral oculomotor palsy

Directory of Open Access Journals (Sweden)

Abhay Gundgurthi

2013-01-01

Full Text Available Nelson′s syndrome refers to a clinical spectrum arising from progressive enlargement of pituitary adenoma and elevated adrenocorticotrophic hormone after total bilateral adrenalectomy for Cushing′s disease comprising of hyperpigmentation, visual field defects which can be life threatening. We report here a 50-year male presenting with rapid onset of Nelson′s syndrome with an unusual finding of bilateral oculomotor palsy mistakenly treated as ocular myasthenia.
Theory of defects in Si and Ge: Past, present and recent developments

International Nuclear Information System (INIS)

Estreicher, S.K.; Backlund, D.; Gibbons, T.M.

2010-01-01

Over the past few decades, considerable progress has been achieved in the theoretical predictions of a wide range of properties of defects in semiconductors. In addition to structures, energetics, spin and charge densities, theory now routinely predicts accurate vibrational properties of defects, and thus connects to the optical characterization of light impurities. However, the positions of gap levels have yet to be predicted with systemically reliable accuracy. Today, supercells much larger than in the past are being used to describe defect centers from first principles. Systems large enough to study the dynamics of extended defects can be handled near the first-principles level. This paper contains a brief review of the key developments that have rendered theory quantitatively useful to experimentalists and an overview of the current 'state-of-the-art' and ongoing developments. Some of the remaining challenges are discussed, with examples in Si and Ge.
Scaling defect decay and the reionization history of the Universe

International Nuclear Information System (INIS)

Avelino, P.P.; Barbosa, D.

2004-01-01

We consider a model for the reionization history of the Universe in which a significant fraction of the observed optical depth is a result of direct reionization by the decay products of a scaling cosmic defect network. We show that such network can make a significant contribution to the reionization history of the Universe even if its energy density is very small (the defect energy density has to be greater than about 10 -11 of the background density). We compute the Cosmic Microwave Background temperature, polarization and temperature-polarization cross power spectrum and show that a contribution to the observed optical depth due to the decay products of a scaling defect network may help to reconcile a high optical depth with a low redshift of complete reionization suggested by quasar data. However, if the energy density of defects is approximately a constant fraction of the background density then these models do not explain the large scale bump in the temperature-polarization cross power spectrum observed by Wilkinson Microwave Anisotropy Probe
[Congenital skull base defect causing recurrent bacterial meningitis].

Science.gov (United States)

Berliner, Elihay; Bar Meir, Maskit; Megged, Orli

2012-08-01

Bacterial meningitis is a life threatening disease. Most patients will experience only one episode throughout life. Children who experience bacterial meningitis more than once, require further immunologic or anatomic evaluation. We report a 9 year old child with five episodes of bacterial meningitis due to a congenital defect of the skull base. A two and a half year old boy first presented to our medical center with pneumococcal meningitis. He was treated with antibiotics and fully recovered. Two months later he presented again with a similar clinical picture. Streptococcus pneumoniae grew in cerebrospinal fluid (CSF) culture. CT scan and later MRI of the brain revealed a defect in the anterior middle fossa floor, with protrusion of brain tissue into the sphenoidal sinus. Corrective surgery was recommended but the parents refused. Three months later, a third episode of pneumococcal meningitis occurred. The child again recovered with antibiotics and this time corrective surgery was performed. Five years later, the boy presented once again with clinical signs and symptoms consistent with bacterial meningitis. CSF culture was positive, but the final identification of the bacteria was conducted by broad spectrum 16S ribosomal RNA PCR (16S rRNA PCR) which revealed a sequence of Neisseria lactamica. CT and MRI showed recurrence of the skull base defect with encephalocele in the sphenoid sinus. The parents again refused neurosurgical intervention. A year later the patient presented with bacterial meningitis. CSF culture obtained after initiation of antibiotics was negative, but actinobacillus was identified in the CSF by 16S rRNA PCR. The patient is scheduled for neurosurgical intervention. In patients with recurrent bacterial meningitis caused by organisms colonizing the oropharynx or nasopharynx, an anatomical defect should be carefully sought and surgically repaired.
Combining the 3D model generated from point clouds and thermography to identify the defects presented on the facades of a building

Science.gov (United States)

Huang, Yishuo; Chiang, Chih-Hung; Hsu, Keng-Tsang

2018-03-01

Defects presented on the facades of a building do have profound impacts on extending the life cycle of the building. How to identify the defects is a crucial issue; destructive and non-destructive methods are usually employed to identify the defects presented on a building. Destructive methods always cause the permanent damages for the examined objects; on the other hand, non-destructive testing (NDT) methods have been widely applied to detect those defects presented on exterior layers of a building. However, NDT methods cannot provide efficient and reliable information for identifying the defects because of the huge examination areas. Infrared thermography is often applied to quantitative energy performance measurements for building envelopes. Defects on the exterior layer of buildings may be caused by several factors: ventilation losses, conduction losses, thermal bridging, defective services, moisture condensation, moisture ingress, and structure defects. Analyzing the collected thermal images can be quite difficult when the spatial variations of surface temperature are small. In this paper the authors employ image segmentation to cluster those pixels with similar surface temperatures such that the processed thermal images can be composed of limited groups. The surface temperature distribution in each segmented group is homogenous. In doing so, the regional boundaries of the segmented regions can be identified and extracted. A terrestrial laser scanner (TLS) is widely used to collect the point clouds of a building, and those point clouds are applied to reconstruct the 3D model of the building. A mapping model is constructed such that the segmented thermal images can be projected onto the 2D image of the specified 3D building. In this paper, the administrative building in Chaoyang University campus is used as an example. The experimental results not only provide the defect information but also offer their corresponding spatial locations in the 3D model.
Position Dependent Spontaneous Emission Spectra of a Λ-Type Atomic System Embedded in a Defective Photonic Crystal

International Nuclear Information System (INIS)

Entezar, S. Roshan

2012-01-01

We investigate the position dependent spontaneous emission spectra of a Λ-type three-level atom with one transition coupled to the free vacuum reservoir and the other one coupled to a double-band photonic band gap reservoir with a defect mode in the band gap. It is shown that, for the atom at the defect location, we have a two-peak spectrum with a wide dark line due to the strong coupling between the atom and the defect mode. While, when the atom is far from the defect location (or in the absence of the defect mode), the spectrum has three peaks with two dark lines due to the coupling between the atom and the photonic band gap reservoir with the largest density of states near the band edges. On the other hand, we have a four-peak spectrum for the atom at the space in between. Moreover, the average spontaneous emission spectra of the atoms uniformly embedded in high dielectric or low dielectric regions are described. It is shown that the atoms embedded in high (low) dielectric regions far from the defect location, effectively couple to the modes of the lower (upper) photonic band. However, the atoms embedded in high dielectric or low dielectric regions at the defect location, are coupled mainly to the defect modes. While, the atoms uniformly embedded in high (low) dielectric regions with a normal distance from the defect location, are coupled to both of defect and lower (upper) photonic band modes. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Optical transitions in two-dimensional topological insulators with point defects

Science.gov (United States)

Sablikov, Vladimir A.; Sukhanov, Aleksei A.

2016-12-01

Nontrivial properties of electronic states in topological insulators are inherent not only to the surface and boundary states, but to bound states localized at structure defects as well. We clarify how the unusual properties of the defect-induced bound states are manifested in optical absorption spectra in two-dimensional topological insulators. The calculations are carried out for defects with short-range potential. We find that the defects give rise to the appearance of specific features in the absorption spectrum, which are an inherent property of topological insulators. They have the form of two or three absorption peaks that are due to intracenter transitions between electron-like and hole-like bound states.
Suspected bacterial meningomyelitis: The first presenting clinical feature of neuromyelitis optica spectrum disorder.

Science.gov (United States)

Li, Xiang; Lin, Jie; Pan, Sipei; Weng, Yiyun; Li, Jia; Zhang, Xu; Xia, Junhui; Tong, Qiaowen

2017-08-15

A rare case of neuromyelitis optica spectrum disorder, suspected to be bacterial meningomyelitis as the initial manifestation, is reported. The patient presented with initial symptoms of meningomyelitis and fever. Cerebrospinal fluid analysis revealed pleocytosis (1280×10 6 /L [98% lymphocytes]) and glucose level of 1.8mmol/L. Magnetic resonance imaging revealed >3 vertebral, longitudinally extensive transverse myelitis and area postrema lesions. Right optic neuritis was experienced 20months after the first attack. Serum anti-aquaporin-4 antibody was positive, and a diagnosis of neuromyelitis optica spectrum disorder was made, supporting the hypothesis that the pathogenesis of neuromyelitis optica is triggered by infection. Copyright © 2017. Published by Elsevier B.V.
Luminescence Properties of Surface Radiation-Induced Defects in Lithium Fluoride

Science.gov (United States)

Voitovich, A. P.; Kalinov, V. S.; Martynovich, E. F.; Novikov, A. N.; Runets, L. P.; Stupak, A. P.

2013-11-01

Luminescence and luminescence excitation spectra are recorded for surface radiation-induced defects in lithium fluoride at temperatures of 77 and 293 K. The presence of three bands with relatively small intensity differences is a distinctive feature of the excitation spectrum. These bands are found to belong to the same type of defects. The positions of the peaks and the widths of the absorption and luminescence bands for these defects are determined. The luminescence decay time is measured. All the measured characteristics of these surface defects differ from those of previously known defects induced by radiation in the bulk of the crystals. It is found that the luminescence of surface defects in an ensemble of nanocrystals with different orientations is not polarized. The number of anion vacancies in the surface defects is estimated using the polarization measurements. It is shown that radiative scattering distorts the intensity ratios of the luminescence excitation bands located in different spectral regions.
Myxoinflammatory fibroblastic sarcoma: spectrum of disease and imaging presentation

Energy Technology Data Exchange (ETDEWEB)

Gaetke-Udager, Kara; Yablon, Corrie M.; Morag, Yoav [University of Michigan Health System, Department of Radiology, Ann Arbor, MI (United States); Lucas, David R. [University of Michigan Health System, Department of Pathology, Ann Arbor, MI (United States)

2016-03-15

To describe the imaging findings of a series of myxoinflammatory fibroblastic sarcomas (MFSs) from our institution, including a case of dedifferentiated MFS and two cases with areas of high-grade tumor, in addition to typical cases of low-grade tumor. To correlate the imaging findings with the pathologic features of these tumors. IRB approval was obtained. Retrospective search of the pathology database at our institution from 2000 to 2015 identified seven cases of MFS with available imaging. Imaging, pathology, and clinical data were reviewed. Unlike the majority of well-differentiated tumors in our series (four cases), one tumor showed dedifferentiation and two cases had areas of high-grade tumor. The dedifferentiated tumor showed peripheral post-contrast enhancement. One case with a substantial high-grade component showed osseous destruction and peripheral enhancement in the high-grade area, while the low-grade component enhanced diffusely. The second case had a small high-grade area and showed diffuse enhancement. All three of these cases had non-acral locations and lacked association with a tendon. The four cases of low-grade MFS demonstrated diffuse enhancement, were located in the distal extremities, and were associated with a tendon. The imaging findings of dedifferentiated and high-grade MFS differ from the more typical low-grade tumors in that they have nonenhancing areas, a non-acral location, lack association with a tendon, and may involve bone. The radiologist should be aware that MFS represents a spectrum that includes low-grade tumors, tumors with high-grade areas, and tumors with dedifferentiation and that this spectrum presents with differing imaging features. (orig.)
Vibrational characteristics of FRP-bonded concrete interfacial defects in a low frequency regime

Science.gov (United States)

Cheng, Tin Kei; Lau, Denvid

2014-04-01

As externally bonded fiber-reinforced polymer (FRP) is a critical load-bearing component of strengthened or retrofitted civil infrastructures, the betterment of structural health monitoring (SHM) methodology for such composites is imperative. Henceforth the vibrational characteristics of near surface interfacial defects involving delamination and trapped air pockets at the FRP-concrete interface are investigated in this study using a finite element approach. Intuitively, due to its lower interfacial stiffness compared with an intact interface, a damaged region is expected to have a set of resonance frequencies different from an intact region when excited by acoustic waves. It has been observed that, when excited acoustically, both the vibrational amplitudes and frequency peaks in the response spectrum of the defects demonstrate a significant deviation from an intact FRP-bonded region. For a thin sheet of FRP bonded to concrete with sizable interfacial defects, the fundamental mode under free vibration is shown to be relatively low, in the order of kHz. Due to the low resonance frequencies of the defects, the use of low-cost equipment for interfacial defect detection via response spectrum analysis is highly feasible.
Exact scale-invariant background of gravitational waves from cosmic defects.

Science.gov (United States)

Figueroa, Daniel G; Hindmarsh, Mark; Urrestilla, Jon

2013-03-08

We demonstrate that any scaling source in the radiation era produces a background of gravitational waves with an exact scale-invariant power spectrum. Cosmic defects, created after a phase transition in the early universe, are such a scaling source. We emphasize that the result is independent of the topology of the cosmic defects, the order of phase transition, and the nature of the symmetry broken, global or gauged. As an example, using large-scale numerical simulations, we calculate the scale-invariant gravitational wave power spectrum generated by the dynamics of a global O(N) scalar theory. The result approaches the large N theoretical prediction as N(-2), albeit with a large coefficient. The signal from global cosmic strings is O(100) times larger than the large N prediction.
Fetal alcohol spectrum disorders har fået danske kriterier

DEFF Research Database (Denmark)

Broccia, Marcella; Vikre-Jørgensen, Jennifer; Rausgaard, Nete Lundager Klokker

2017-01-01

The Danish Paediatric Society presents the first Danish definition of fetal alcohol spectrum disorders (FASD) in a new guideline. FASD is an umbrella term for conditions caused by prenatal alcohol exposure. To varying degrees, fetal alcohol damages manifest as physical defects, characteristic...... facial features and poor growth, as well as behavioural and cognitive disorders. It requires both somatic and psychological evaluation to identify these damages. Early diagnosis and identification of problems are important for prognosis as professional care has a positive preventive effect...
Influence of defects in SiC (0001) on epitaxial graphene

International Nuclear Information System (INIS)

Guo Yu; Guo Li-Wei; Lu Wei; Huang Jiao; Jia Yu-Ping; Sun Wei; Li Zhi-Lin; Wang Yi-Fei

2014-01-01

Defects in silicon carbide (SiC) substrate are crucial to the properties of the epitaxial graphene (EG) grown on it. Here we report the effect of defects in SiC on the crystalline quality of EGs through comparative studies of the characteristics of the EGs grown on SiC (0001) substrates with different defect densities. It is found that EGs on high quality SiC possess regular steps on the surface of the SiC and there is no discernible D peak in its Raman spectrum. Conversely, the EG on the SiC with a high density of defects has a strong D peak, irregular stepped morphology and poor uniformity in graphene layer numbers. It is the defects in the SiC that are responsible for the irregular stepped morphology and lead to the small domain size in the EG. (rapid communication)
Characterization of lacunar defects by positrons annihilation

International Nuclear Information System (INIS)

Barthe, M.F.; Corbel, C.; Blondiaux, G.

2003-01-01

Among the nondestructive methods for the study of matter, the positrons annihilation method allows to sound the electronic structure of materials by measuring the annihilation characteristics. These characteristics depend on the electronic density as seen by the positon, and on the electron momentums distribution which annihilate with the positon. The positon is sensible to the coulombian potential variations inside a material and sounds preferentially the regions away from nuclei which represent potential wells. The lacunar-type defects (lack of nuclei) represent deep potential wells which can trap the positon up to temperatures close to the melting. This article describes the principles of this method and its application to the characterization of lacunar defects: 1 - positrons: matter probes (annihilation of electron-positon pairs, annihilation characteristics, positrons sources); 2 - positrons interactions in solids (implantation profiles, annihilation states, diffusion and trapping, positon lifetime spectrum: evolution with the concentration of defects); 3 - measurement of annihilation characteristics with two gamma photons (lifetime spectroscopy with the β + 22 Na isotope, spectroscopy of Doppler enlargement of the annihilation line); 4 - determination of the free volume of defects inside or at the surface of materials (annihilation signature in lacunar defects, lacuna, lacunar clusters and cavities, acceptors nature in semiconductors: ionic or lacunar, interface defects, precipitates in alloys); 5 - conclusions. (J.S.)
Impressions of the Meson Spectrum: Hybrids & Exotics, present and future

Energy Technology Data Exchange (ETDEWEB)

Pennington, Michael R. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

2016-03-25

It has long been expected that the spectrum of hadrons in QCD would be far richer and extensive than experiment has so far revealed. While there have been experimental hints of this richness for some time, it is really only in the last few years that dramatic progress has been seen in the exploration both experimentally and in calculations on the lattice. Precision studies enabled by new technology both with detectors and high performance computations are converging on an understanding of the spectrum in strong coupling QCD. These methodologies are laying the foundation for a decade of potential discovery that electro and photoproduction experiments at Jefferson Lab, which when combined with key results on B and charmonium decays from both e+e? and pp colliders, should turn mere impressions of the light meson spectrum into a high definition picture.
Studies on intrinsic defects related to Zn vacancy in ZnO nanoparticles

International Nuclear Information System (INIS)

Singh, V.P.; Das, D.; Rath, Chandana

2013-01-01

Graphical abstract: Display Omitted Highlights: ► Williamson–Hall analysis of ZnO indicates strain in the lattice and size is of 20 nm. ► PL shows a broad emission peak in visible range due to native defects. ► Raman active modes corresponding to P6 3 mc and a few additional modes are observed. ► FTIR detects few local vibrational modes of hydrogen attached to zinc vacancies. ► V Zn -H and Zn + O divacancies are confirmed by PAS. -- Abstract: ZnO being a well known optoelectronic semiconductor, investigations related to the defects are very promising. In this report, we have attempted to detect the defects in ZnO nanoparticles synthesized by the conventional coprecipitation route using various spectroscopic techniques. The broad emission peak observed in photoluminescence spectrum and the non zero slope in Williamson–Hall analysis indicate the defects induced strain in the ZnO lattice. A few additional modes observed in Raman spectrum could be due to the breakdown of the translation symmetry of the lattice caused by defects and/or impurities. The presence of impurities can be ruled out as XRD pattern shows pure wurtzite structure. The presence of the vibrational band related to the Zn vacancies (V Zn ), unintentional hydrogen dopants and their complex defects confirm the defects in ZnO lattice. Positron life time components τ 1 and τ 2 additionally support V Zn attached to hydrogen and to a cluster of Zn and O di-vacancies respectively.
Maxillectomy defects: a suggested classification scheme.

Science.gov (United States)

Akinmoladun, V I; Dosumu, O O; Olusanya, A A; Ikusika, O F

2013-06-01

The term "maxillectomy" has been used to describe a variety of surgical procedures for a spectrum of diseases involving a diverse anatomical site. Hence, classifications of maxillectomy defects have often made communication difficult. This article highlights this problem, emphasises the need for a uniform system of classification and suggests a classification system which is simple and comprehensive. Articles related to this subject, especially those with specified classifications of maxillary surgical defects were sourced from the internet through Google, Scopus and PubMed using the search terms maxillectomy defects classification. A manual search through available literature was also done. The review of the materials revealed many classifications and modifications of classifications from the descriptive, reconstructive and prosthodontic perspectives. No globally acceptable classification exists among practitioners involved in the management of diseases in the mid-facial region. There were over 14 classifications of maxillary defects found in the English literature. Attempts made to address the inadequacies of previous classifications have tended to result in cumbersome and relatively complex classifications. A single classification that is based on both surgical and prosthetic considerations is most desirable and is hereby proposed.
Defect formation in heavily doped Si upon irradiation

International Nuclear Information System (INIS)

Gubskaya, V.I.; Kuchinskii, P.V.; Lomako, V.M.

1981-01-01

The rates of the carrier removal and radiation defect introduction into n- and p-Si in the concentration range of 10 14 to 10 17 cm -3 upon 7-MeV-electron irradiation have been studied. The spectrum of the vacancy-type defects, defining the carrier removal rate in lightly doped crystals has been found. With doping level increase the carrier removal rate grows irrespective of conductivity type, and at n 0 , p 0 > 10 17 cm -3 is close to the total displacement number. At the same time a decrease in the introduction rate of the known vacancy-type defects is observed. x It is shown that a considerable growth of the carrier removal rate is defined neither by introduction of shallow compensating centers, nor by change in the primary defect charge state. It is suggested that at high doping impurity concentrations compensation in Si is due to the introduction of complexes doping impurity-interstitial or (impurity atom-interstitial) + vacancy, which give deep levels. (author)
Advanced defect detection algorithm using clustering in ultrasonic NDE

Science.gov (United States)

Gongzhang, Rui; Gachagan, Anthony

2016-02-01

A range of materials used in industry exhibit scattering properties which limits ultrasonic NDE. Many algorithms have been proposed to enhance defect detection ability, such as the well-known Split Spectrum Processing (SSP) technique. Scattering noise usually cannot be fully removed and the remaining noise can be easily confused with real feature signals, hence becoming artefacts during the image interpretation stage. This paper presents an advanced algorithm to further reduce the influence of artefacts remaining in A-scan data after processing using a conventional defect detection algorithm. The raw A-scan data can be acquired from either traditional single transducer or phased array configurations. The proposed algorithm uses the concept of unsupervised machine learning to cluster segmental defect signals from pre-processed A-scans into different classes. The distinction and similarity between each class and the ensemble of randomly selected noise segments can be observed by applying a classification algorithm. Each class will then be labelled as `legitimate reflector' or `artefacts' based on this observation and the expected probability of defection (PoD) and probability of false alarm (PFA) determined. To facilitate data collection and validate the proposed algorithm, a 5MHz linear array transducer is used to collect A-scans from both austenitic steel and Inconel samples. Each pulse-echo A-scan is pre-processed using SSP and the subsequent application of the proposed clustering algorithm has provided an additional reduction to PFA while maintaining PoD for both samples compared with SSP results alone.
Vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association with Mayer-Rokitansky-Küster-Hauser syndrome in co-occurrence: two case reports and a review of the literature.

Science.gov (United States)

Bjørsum-Meyer, Thomas; Herlin, Morten; Qvist, Niels; Petersen, Michael B

2016-12-21

The vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association and Mayer-Rokitansky-Küster-Hauser syndrome are rare conditions. We aimed to present two cases with the vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association and Mayer-Rokitansky-Küster-Hauser co-occurrence from our local surgical center and through a systematic literature search detect published cases. Furthermore, we aimed to collect existing knowledge in the embryopathogenesis and genetics in order to discuss a possible link between the vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association and Mayer-Rokitansky-Küster-Hauser syndrome. Our first case was a white girl delivered by caesarean section at 37 weeks of gestation; our second case was a white girl born at a gestational age of 40 weeks. A co-occurrence of vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal defect, and limb defect association and Mayer-Rokitansky-Küster-Hauser syndrome was diagnosed in both cases. We performed a systematic literature search in PubMed ((VACTERL) OR (VATER)) AND ((MRKH) OR (Mayer-Rokitansky-Küster-Hauser) OR (mullerian agenesis) OR (mullerian aplasia) OR (MURCS)) without limitations. A similar search was performed in Embase and the Cochrane library. We added two cases from our local center. All cases (n = 9) presented with anal atresia and renal defect. Vertebral defects were present in eight patients. Rectovestibular fistula was confirmed in seven patients. Along with the uterovaginal agenesis, fallopian tube aplasia appeared in five of nine cases and in two cases ovarian involvement also existed. The co-occurrence of the vertebral defect, anal atresia, cardiac defect, tracheoesophageal fistula/esophageal atresia, renal
The exact solution of the Ising quantum chain with alternating single and sector defects

International Nuclear Information System (INIS)

Zhang Degang; Li Bozang; Li Yun

1992-10-01

The Ising quantum chain with alternating single and sector defects is solved exactly by using the technique of Lieb, Schultz and Mattis. The energy spectrum of this model is shown to have a tower structure if and only if these defects constitute a commensurate configuration. This means that conformal invariance is preserved under these circumstances. (author). 13 refs
Self-Presentation and the Role of Perspective Taking and Social Motivation in Autism Spectrum Disorder

NARCIS (Netherlands)

Scheeren, Anke M; Banerjee, Robin; Koot, Hans M; Begeer, Sander

We compared self-presentation abilities of 132 children and adolescents with autism spectrum disorders (ASD) to those of 41 typically developing (TD) peers, and examined the potential link with their social motivation and perspective taking. Participants introduced themselves to an interviewer in a
Self-presentation and the role of perspective taking and social motivation in autism spectrum disorder

NARCIS (Netherlands)

Scheeren, A.M.; Banerjee, Robin; Koot, Hans M.; Begeer, Sander

2016-01-01

We compared self-presentation abilities of 132 children and adolescents with autism spectrum disorders (ASD) to those of 41 typically developing (TD) peers, and examined the potential link with their social motivation and perspective taking. Participants introduced themselves to an interviewer in a
IR thermography methods for evaluation of internal defects in light composite armours

International Nuclear Information System (INIS)

Swiderski, W.; Szabra, D.; Szudrowicz, M.

2009-01-01

Complete text of publication follows. Light composite armour is a preferred solution against military and paramilitary sources of present threats as the reducing mass of battle vehicles provides a possibility of their quick air-transport. The light armours of these vehicles should be resistant against: common and rifle bullets, grenades, anti-personal mines, IED - improvised explosive devices. The range of military applications anticipated for composite armours covers a broad spectrum of materials and designs. Materials of composite armours include graphite epoxy, glass epoxy and aramid fiber composites. The composites that have been examined can include a variety of defects, such as ballistic impacts, embedded defects, manufacturing defects, thermal damage, moisture ingress and other induced defects. Methods for testing ballistic protection of light armours are known and used. First of all they consist of checking armours resistance against the bullets where the bullet velocity is known. Moreover the V50 velocity is defined during the test. In this method the V 50 velocity of a round or standard fragment is defined (according to STANAG 2920) as the velocity at which armour is penetrated at the probability 50%. The distribution of points hit by bullets or fragments on the surface of an armour is also important. In fact, only correct distribution of these points provides a guaranty for an impartial assessment of tested designs. After hitting by a bullet, shape and size of an area of damage in composite armours depends on the type and design of armour, and type of reinforcing material is particularly important. Knowledge of damage characteristics allows to arrange hitting points to avoid overlapping of damaged areas. Nondestructive testing by using IR thermography methods is very useful in evaluation of internal defects. In the paper we present the dependence between the energy of fragments/or bullets and the dimension of internal defects. (author)
Synaptic proteins and receptors defects in autism spectrum disorders

OpenAIRE

Chen, Jianling; Yu, Shunying; Fu, Yingmei; Li, Xiaohong

2014-01-01

Recent studies have found that hundreds of genetic variants, including common and rare variants, rare and de novo mutations, and common polymorphisms have contributed to the occurrence of autism spectrum disorders (ASDs). The mutations in a number of genes such as neurexin, neuroligin, postsynaptic density protein 95 (PSD-95), SH3 and multiple ankyrin repeat domains 3 (SHANK3), synapsin, gephyrin, cadherin (CDH) and protocadherin (PCDH), thousand-and-one-amino acid 2 kinase (TAOK2), and conta...

Quantitative Evaluation of Defect in Stainless Steel 304 Tube Using Pulsed Eddy Current Technique

International Nuclear Information System (INIS)

Nurul Ain Ahmad Latif; Ilham Mukriz Zainal Abidin; Nurul Ain Ahmad Latif; Nordin Jamaludin; Zaredah Hashim; Norhayati Ramli

2016-01-01

Pulsed eddy current (PEC) is an advanced non-destructive testing (NDT) technique that operates based on electromagnetic principle. The excitation consists of broad frequency spectrum leading to be a potential in detecting defects that are deeply buried inside the specimen. In this paper, the experiment and simulation were conducted on stainless steel plate 304 fabricated with open surface defects having a different defect depth as an investigation towards the correlation between extracted signal feature and defect depth. Two common features; time to peak and peak value that corresponds to the location depth of defect and size of defect were used for signals analysis and evaluation. The results that acquired through finite element method (FEM) simulation were compared with experimental results for the signals evaluation and defect quantification. (author)
Webinar Presentation: Air Pollution and Autism Spectrum Disorder: What Do We Know and What Is Next?

Science.gov (United States)

This presentation, Air Pollution and Autism Spectrum Disorder: What Do We Know and What Is Next?, was given at the NIEHS/EPA Children's Centers 2015 Webinar Series: Brain Health held on Aug. 12, 2015.
Structure defects in malachite revealed by positron annihilation

International Nuclear Information System (INIS)

Geffroy, B.; Diallo, I.; Paulin, R.

1984-01-01

Positron lifetime is measured between 77 and 400 K in two malachite samples with different mineralogical structures. The complex spectrum found in zoned malachite reveals a microporosity which remains stable in this range of temperature. Besides, above 200 K, equilibrium defects appear. Their formation energy is estimated to be Esub(f) = 0.27 +- 0.02 eV [fr
Structure defects in malachite revealed by positron annihilation

Energy Technology Data Exchange (ETDEWEB)

Geffroy, B; Diallo, I; Paulin, R [Institut National des Sciences et Techniques Nucleaires, CEN/Saclay, 91 - Gif-sur-Yvette (France)

1984-01-01

Positron lifetime is measured between 77 and 400 K in two malachite samples with different mineralogical structures. The complex spectrum found in zoned malachite reveals a microporosity which remains stable in this range of temperature. Besides, above 200 K, equilibrium defects appear. Their formation energy is estimated to be Esub(f) = 0.27 +- 0.02 eV.
Synthetic Defects for Vibrothermography

Science.gov (United States)

Renshaw, Jeremy; Holland, Stephen D.; Thompson, R. Bruce; Eisenmann, David J.

2010-02-01

Synthetic defects are an important tool used for characterizing the performance of nondestructive evaluation techniques. Viscous material-filled synthetic defects were developed for use in vibrothermography (also known as sonic IR) as a tool to improve inspection accuracy and reliability. This paper describes how the heat-generation response of these VMF synthetic defects is similar to the response of real defects. It also shows how VMF defects can be applied to improve inspection accuracy for complex industrial parts and presents a study of their application in an aircraft engine stator vane.
Application of ENDOR-induced electron spin resonance to the study of point defects in solids

International Nuclear Information System (INIS)

Niklas, J.R.; Spaeth, J.M.

1980-01-01

The technique of ENDOR-induced ESR (EI-ESR) is applied to the investigation of several point defects in insulating crystals. It is shown that the lineshape of the EI-ESR spectrum depends on the ENDOR line used for the experiment. The EI-ESR technique allows the separation of overlapping ESR spectra in the presence of several defects. New applications are the selection of spin states and the determination of relative signs of spin-Hamiltonian parameters, the selection of centre orientations and the assignment of nuclei in complex ENDOR spectra, and the determination of quadrupole interactions which are not resolved in the ENDOR spectrum. (author)
Ehlers-danlos syndrome with platelet aggregation defect-presenting as mysterious bleeding disorder

Directory of Open Access Journals (Sweden)

Sawhney M

2003-03-01

Full Text Available A 7-year-old girl presented with recurrent episodes of petechiae, purpura and ecchymoses since six months of age and recurrent episodes of mild to severe epistaxis since two years of age requiring repeated blood transfusions. In April '99 while being investigated for a massive epistaxis, she was found to have platelet function defect with abnormal aggregation of platelets to ADP, epinephrine, collagen as well as to ristocetin. Further investigations ruled out the possibility of Glanzmann's disorder and von-Willebrand's disease as to its cause. In May 2001 she was referred to the dermatologist for evaluation of subcutaneous tumours, which had developed since the last six months. On clinical evaluation, she was found to be having mild hyperextensibility of the skin, joint hypermobility, atrophic scars over knee, spontaneous bruises over right forearm and left thigh and nontender firm to hard subcutaneous nodules over both wrists, both shoulders, right index finger and dorsum of right foot consistent with a clinical picture of a mild form of Ehlers-Danlos syndrome (EDS. Histopathology of the nodule from left wrist was consistent with molluscoid tumour of EDS and skin histopathology and ultrastructure studies showed thick irregular collagen fibrils. Only other sibling, a five-year-old male also had history of repeated mild to moderate epistaxis and on examination was found to have a milder variant of EDS. Born out of I degree consanguineous marriage of normal parents with mildly affected other sibling, she was diagnosed to be suffering from EDS with autosomal recessive inheritance, most probably EDS type X due to the associated platelet aggregation defect. Only one such family with EDS type X has been reported so far.
Ehlers-danlos syndrome with platelet aggregation defect-presenting as mysterious bleeding disorder

Directory of Open Access Journals (Sweden)

Sawhney M

2003-01-01

Full Text Available A 7-year-old girl presented with recurrent episodes of petechiae, purpura and ecchymoses since six months of age and recurrent episodes of mild to severe epistaxis since two years of age requiring repeated blood transfusions. In April '99 while being investigated for a massive epistaxis, she was found to have platelet function defect with abnormal aggregation of platelets to ADP, epinephrine, collagen as well as to ristocetin. Further investigations ruled out the possibility of Glanzmann's disorder and von-Willebrand's disease as to its cause. In May 2001 she was referred to the dermatologist for evaluation of subcutaneous tumours, which had developed since the last six months. On clinical evaluation, she was found to be having mild hyperextensibility of the skin, joint hypermobility, atrophic scars over knee, spontaneous bruises over right forearm and left thigh and nontender firm to hard subcutaneous nodules over both wrists, both shoulders, right index finger and dorsum of right foot consistent with a clinical picture of a mild form of Ehlers-Danlos syndrome (EDS. Histopathology of the nodule from left wrist was consistent with molluscoid tumour of EDS and skin histopathology and ultrastructure studies showed thick irregular collagen fibrils. Only other sibling, a five-year-old male also had history of repeated mild to moderate epistaxis and on examination was found to have a milder variant of EDS. Born out of I degree consanguineous marriage of normal parents with mildly affected other sibling, she was diagnosed to be suffering from EDS with autosomal recessive inheritance, most probably EDS type X due to the associated platelet aggregation defect. Only one such family with EDS type X has been reported so far.
Self-Presentation and the Role of Perspective Taking and Social Motivation in Autism Spectrum Disorder

Science.gov (United States)

Scheeren, Anke M.; Banerjee, Robin; Koot, Hans M.; Begeer, Sander

2016-01-01

We compared self-presentation abilities of 132 children and adolescents with autism spectrum disorders (ASD) to those of 41 typically developing (TD) peers, and examined the potential link with their social motivation and perspective taking. Participants introduced themselves to an interviewer in a baseline condition (without incentive) and a…
P-N defect in GaNP studied by optically detected magnetic resonance

International Nuclear Information System (INIS)

Chen, W.M.; Thinh, N.Q.; Vorona, I.P.; Buyanova, I.A.; Xin, H.P.; Tu, C.W.

2003-01-01

We provide experimental evidence for an intrinsic defect in GaNP from optically detected magnetic resonance (ODMR). This defect is identified as a P-N complex, exhibiting hyperfine structure due to interactions with a nuclear spin I=((1)/(2)) of one P atom and also a nuclear spin I=1 due to one N atom. The introduction of the defect is assisted by the incorporation of N within the studied N composition range of up to 3.1%, under non-equilibrium growth conditions during gas-source molecular beam epitaxy. The corresponding ODMR spectrum was found to be isotropic, suggesting an A 1 symmetry of the defect state. The localization of the electron wave function at the P-N defect in GaNP is found to be even stronger than that for the isolated P Ga antisite in its parent binary compound GaP
Defect of the Eyelids.

Science.gov (United States)

Lu, Guanning Nina; Pelton, Ron W; Humphrey, Clinton D; Kriet, John David

2017-08-01

Eyelid defects disrupt the complex natural form and function of the eyelids and present a surgical challenge. Detailed knowledge of eyelid anatomy is essential in evaluating a defect and composing a reconstructive plan. Numerous reconstructive techniques have been described, including primary closure, grafting, and a variety of local flaps. This article describes an updated reconstructive ladder for eyelid defects that can be used in various permutations to solve most eyelid defects. Copyright © 2017 Elsevier Inc. All rights reserved.
[Multi-Target Recognition of Internal and External Defects of Potato by Semi-Transmission Hyperspectral Imaging and Manifold Learning Algorithm].

Science.gov (United States)

Huang, Tao; Li, Xiao-yu; Jin, Rui; Ku, Jing; Xu, Sen-miao; Xu, Meng-ling; Wu, Zhen-zhong; Kong, De-guo

2015-04-01

The present paper put forward a non-destructive detection method which combines semi-transmission hyperspectral imaging technology with manifold learning dimension reduction algorithm and least squares support vector machine (LSSVM) to recognize internal and external defects in potatoes simultaneously. Three hundred fifteen potatoes were bought in farmers market as research object, and semi-transmission hyperspectral image acquisition system was constructed to acquire the hyperspectral images of normal external defects (bud and green rind) and internal defect (hollow heart) potatoes. In order to conform to the actual production, defect part is randomly put right, side and back to the acquisition probe when the hyperspectral images of external defects potatoes are acquired. The average spectrums (390-1,040 nm) were extracted from the region of interests for spectral preprocessing. Then three kinds of manifold learning algorithm were respectively utilized to reduce the dimension of spectrum data, including supervised locally linear embedding (SLLE), locally linear embedding (LLE) and isometric mapping (ISOMAP), the low-dimensional data gotten by manifold learning algorithms is used as model input, Error Correcting Output Code (ECOC) and LSSVM were combined to develop the multi-target classification model. By comparing and analyzing results of the three models, we concluded that SLLE is the optimal manifold learning dimension reduction algorithm, and the SLLE-LSSVM model is determined to get the best recognition rate for recognizing internal and external defects potatoes. For test set data, the single recognition rate of normal, bud, green rind and hollow heart potato reached 96.83%, 86.96%, 86.96% and 95% respectively, and he hybrid recognition rate was 93.02%. The results indicate that combining the semi-transmission hyperspectral imaging technology with SLLE-LSSVM is a feasible qualitative analytical method which can simultaneously recognize the internal and
Point defects in solids

International Nuclear Information System (INIS)

Anon.

1978-01-01

The principal properties of point defects are studied: thermodynamics, electronic structure, interactions with etended defects, production by irradiation. Some measuring methods are presented: atomic diffusion, spectroscopic methods, diffuse scattering of neutron and X rays, positron annihilation, molecular dynamics. Then points defects in various materials are investigated: ionic crystals, oxides, semiconductor materials, metals, intermetallic compounds, carbides, nitrides [fr
A comparative study on defect estimation using XPS and Raman spectroscopy in few layer nanographitic structures.

Science.gov (United States)

Ganesan, K; Ghosh, Subrata; Gopala Krishna, Nanda; Ilango, S; Kamruddin, M; Tyagi, A K

2016-08-10

Defects in planar and vertically oriented nanographitic structures (NGSs) synthesized by plasma enhanced chemical vapor deposition (PECVD) have been investigated using Raman and X-ray photoelectron spectroscopy. While Raman spectra reveal the dominance of vacancy and boundary type defects respectively in vertical and planar NGSs, XPS provides additional information on vacancy related defect peaks in the C 1s spectrum, which originate from non-conjugated carbon atoms in the hexagonal lattice. Although an excellent correlation prevails between these two techniques, our results show that estimation of surface defects by XPS is more accurate than Raman analysis. Nuances of these techniques are discussed in the context of assessing defects in nanographitic structures.
Exploring the multiverse with topological defects

Science.gov (United States)

Zhang, Jun

Inflationary cosmology suggests a nontrivial spacetime structure on scales beyond our observable universe, the multiverse. Based on the observation that topological defects and vacuum bubbles can spontaneously nucleate in a de Sitter like inflating space, we explore two different aspects of the multiverse model in this thesis. Hence the main body of this study consists of two parts. In the first part, we investigate domain walls and cosmic strings that may nucleate in the false vacuum. If we live in a bubble universe surrounded by the false vacuum, as suggested by the eternal inflationary multiverse model, the nucleating defects could collide with our bubble universe, and leave potentially observable signals. We investigate different kinds of collisions and their consequences. We suggest such collisions generically result in signals such as radiation and gravitational waves or the defects themselves or a combination of both propagating into our bubble, and therefore provide a new approach to searching for the multiverse. In the second part, we study the fate of domain walls and vacuum bubbles that could nucleate in the slow roll inflation. We show that, depending on their sizes, these objects will form either black holes or wormholes after inflation. We study the spacetime structure of the resulting wormholes. Our analysis indicates the presence of domain walls and vacuum bubbles in the slow roll inflation has significant effects on the global structure of our universe, that is by forming wormholes, it can lead to the picture of a multiverse. We also calculate the mass spectrum of the resulting black holes and wormholes under certain assumptions. We argue that the observation of a population of black holes with such mass spectrum could be considered as evidence of the existence of both inflation and multiverse.
Positron annihilation and electron spin resonance studies of defects in electron-irradiated 3C-SiC

International Nuclear Information System (INIS)

Itoh, Hisayoshi; Yoshikawa, Masahito; Tanigawa, Shoichiro; Nashiyama, Isamu; Misawa, Shunji; Okumura, Hajime; Yoshida, Sadafumi.

1992-01-01

Defects induced by 1 MeV electron-irradiation in cubic silicon carbide (3C-SiC) epitaxially grown by chemical vapor deposition have been studied with positron annihilation and electron spin resonance (ESR). Doppler broadened energy spectra of annihilation γ-rays obtained by using variable-energy positron beams showed the formation of vacancy-type defects in 3C-SiC by the electron-irradiation. An ESR spectrum labeled Tl, which has an isotropic g-value of 2.0029 ± 0.001, was observed in electron-irradiated 3C-SiC. The Tl spectrum is interpreted by hyperfine interactions of paramagnetic electrons with 13 C at four carbon sites and 29 Si at twelve silicon sites, indicating that the Tl center arises from a point defect at a silicon site. Both the results can be accounted for by the introduction of isolated Si vacancies by the irradiation. (author)
Optical spectroscopy of vacancy related defects in silicon carbide generated by proton irradiation

Energy Technology Data Exchange (ETDEWEB)

Kasper, C.; Sperlich, A.; Simin, D.; Astakhov, G.V. [Experimental Physics VI, Julius Maximilian University of Wuerzburg (Germany); Kraus, H. [Japan Atomic EnergyAgency, Takasaki, Gunma (Japan); Experimental Physics VI, Julius Maximilian University of Wuerzburg (Germany); Makino, T.; Sato, S.I.; Ohshima, T. [Japan Atomic EnergyAgency, Takasaki, Gunma (Japan); Dyakonov, V. [Experimental Physics VI, Julius Maximilian University of Wuerzburg (Germany); ZAE Bayern, Wuerzburg (Germany)

2016-07-01

Defects in silicon carbide (SiC) received growing attention in recent years, because they are promising candidates for spin based quantum information processing. In this study we examine silicon vacancies in 4H-SiC crystals generated by proton irradiation. By the use of confocal microscopy the implantation depth of Si vacancies for varying proton energies can be verified. An important issue is to ascertain the nature and distribution of the defects. For this purpose, we use the characteristic photoluminescence spectrum of Si vacancies, whose intensity is proportional to the defect density. Using xyz-scans, where the photoluminescence at each mapping point is recorded, one can thus determine the vacancies nature and their distribution in the SiC crystal. Additionally we verify the nature of the examined defects by measuring their uniquely defined zero-field-splitting by using ODMR associated with defect spins.
Algebra of 2D periodic operators with local and perpendicular defects

DEFF Research Database (Denmark)

Kutsenko, Anton

2016-01-01

We show that 2D periodic operators with local and perpendicular defects form an algebra. We provide an algorithm for finding spectrum for such operators. While the continuous spectral components can be computed by simple algebraic operations on some matrix-valued functions and a few number...
Dental enamel defects in adult coeliac disease: prevalence and correlation with symptoms and age at diagnosis.

Science.gov (United States)

Trotta, Lucia; Biagi, Federico; Bianchi, Paola I; Marchese, Alessandra; Vattiato, Claudia; Balduzzi, Davide; Collesano, Vittorio; Corazza, Gino R

2013-12-01

Coeliac disease is a condition characterized by a wide spectrum of clinical manifestations. Any organ can be affected and, among others, dental enamel defects have been described. Our aims were to study the prevalence of dental enamel defects in adults with coeliac disease and to investigate a correlation between the grade of teeth lesion and clinical parameters present at the time of diagnosis of coeliac disease. A dental examination was performed in 54 coeliac disease patients (41 F, mean age 37 ± 13 years, mean age at diagnosis 31 ± 14 years). Symptoms leading to diagnosis were diarrhoea/weight loss (32 pts.), anaemia (19 pts.), familiarity (3 pts.); none of the patients was diagnosed because of enamel defects. At the time of evaluation, they were all on a gluten-free diet. Enamel defects were classified from grade 0 to 4 according to its severity. Enamel defects were observed in 46/54 patients (85.2%): grade 1 defects were seen in 18 patients (33.3%) grade 2 in 16 (29.6%), grade 3 in 8 (14.8%), and grade 4 in 4 (7.4%). We also observed that grades 3 and 4 were more frequent in patients diagnosed with classical rather than non-classical coeliac disease (10/32 vs. 2/20). However, this was not statistically significant. This study confirms that enamel defects are common in adult coeliac disease. Observation of enamel defects is an opportunity to diagnose coeliac disease. Copyright © 2013 European Federation of Internal Medicine. Published by Elsevier B.V. All rights reserved.
First report of the mutational and phenotypic spectrum of Hereditary Spherocytosis in Indian patients by targeted resequencing

Directory of Open Access Journals (Sweden)

Anu Aggarwal

2017-10-01

This first ever study on the molecular spectrum of HS from India revealed predominantly sporadic and dominantly-inherited defects in ANK1 and SPTB in patients. Most of the cases (70% presented at an early age with jaundice and anemia. Co-inherited G6PD deficiency and Gilbert’s syndrome led to phenotypic variability. NGS provided a sensitive, cost-effective and rapid tool for understanding the molecular pathology of HS patients.

Raman spectrum of asphaltene

KAUST Repository

Abdallah, Wael A.

2012-11-05

Asphaltenes extracted from seven different crude oils representing different geological formations from around the globe were analyzed using the Raman spectroscopic technique. Each spectrum is fitted with four main peaks using the Gaussian function. On the basis of D1 and G bands of the Raman spectrum, asphaltene indicated an ordered structure with the presence of boundary defected edges. The average aromatic sheet size of the asphaltene molecules is estimated within the range of 1.52-1.88 nm, which represents approximately seven to eight aromatic fused rings. This estimation is based on the integrated intensity of D1 and G bands, as proposed by Tunistra and Koenig. The results here are in perfect agreement with so many other used techniques and indicate the potential applicability of Raman measurements to determine the average aromatic ring size and its boundary. © 2012 American Chemical Society.
Raman spectrum of asphaltene

KAUST Repository

Abdallah, Wael A.; Yang, Yang

2012-01-01

Asphaltenes extracted from seven different crude oils representing different geological formations from around the globe were analyzed using the Raman spectroscopic technique. Each spectrum is fitted with four main peaks using the Gaussian function. On the basis of D1 and G bands of the Raman spectrum, asphaltene indicated an ordered structure with the presence of boundary defected edges. The average aromatic sheet size of the asphaltene molecules is estimated within the range of 1.52-1.88 nm, which represents approximately seven to eight aromatic fused rings. This estimation is based on the integrated intensity of D1 and G bands, as proposed by Tunistra and Koenig. The results here are in perfect agreement with so many other used techniques and indicate the potential applicability of Raman measurements to determine the average aromatic ring size and its boundary. © 2012 American Chemical Society.
Aggression in autism spectrum disorder: presentation and treatment options

Directory of Open Access Journals (Sweden)

Fitzpatrick SE

2016-06-01

Full Text Available Sarah E Fitzpatrick, Laura Srivorakiat, Logan K Wink, Ernest V Pedapati, Craig A Erickson Cincinnati Children’s Hospital Medical Center, University of Cincinnati College of Medicine, Cincinnati, OH, USA Abstract: Autism spectrum disorder (ASD is a neurodevelopmental disorder characterized by persistent difficulties in social communication and social interaction, coupled with restricted, repetitive patterns of behavior or interest. Research indicates that aggression rates may be higher in individuals with ASD compared to those with other developmental disabilities. Aggression is associated with negative outcomes for children with ASD and their caregivers, including decreased quality of life, increased stress levels, and reduced availability of educational and social support. Therapeutic strategies including functional behavioral assessment, reinforcement strategies, and functional communication training may have a significant impact in reducing the frequency and intensity of aggressive behavior in individuals with ASD. Pharmacologic treatments, particularly the use of second-generation antipsychotics, may also be of some benefit in reducing aggression in individuals with ASD. With the ever-increasing rate of ASD diagnosis, development of effective therapeutic and pharmacologic methods for preventing and treating aggression are essential to improving outcomes in this disorder. Keywords: autism, autism spectrum disorder, aggression, treatment, antipsychotics, applied behavior analysis
Characterizing the Peak in the Cosmic Microwave Background Angular Power Spectrum

Science.gov (United States)

Knox, Lloyd; Page, Lyman

2000-08-01

A peak has been unambiguously detected in the cosmic microwave background angular spectrum. Here we characterize its properties with fits to phenomenological models. We find that the TOCO and BOOM/NA data determine the peak location to be in the range 175-243 and 151-259, respectively (at 95% confidence) and determine the peak amplitude to be between ~70 and 90 μK. The peak shape is consistent with inflation-inspired flat, cold dark matter plus cosmological constant models of structure formation with adiabatic, nearly scale invariant initial conditions. It is inconsistent with open models and presents a great challenge to defect models.
The inelastic contribution to high resolution images of defects

International Nuclear Information System (INIS)

Krivanek, O.L.; Ahn, C.C.; Wood, G.J.

1990-01-01

The importance of the contribution due to inelastically scattered electrons to unfiltered HREM images is examined, with emphasis on imaging of defects in semiconductors. Whenever the low energy loss spectrum contains sharp peaks, the contribution is not featureless. At specimen thickness of a few tens of nm, it may change the image appearance in a major way. The strongest effect occurs in high resolution, medium voltage (200 to 500 kV) electron microscope images of defects at focus values minimizing the contrast of the elastic image in low Z materials such as Al and Si. In higher Z materials or those with no sharp 'plasmons', the contribution is small. 23 refs., 8 figs
Defects in ZnO nanorods prepared by a hydrothermal method.

Science.gov (United States)

Tam, K H; Cheung, C K; Leung, Y H; Djurisić, A B; Ling, C C; Beling, C D; Fung, S; Kwok, W M; Chan, W K; Phillips, D L; Ding, L; Ge, W K

2006-10-26

ZnO nanorod arrays were fabricated using a hydrothermal method. The nanorods were studied by scanning electron microscopy, photoluminescence (PL), time-resolved PL, X-ray photoelectron spectroscopy, and positron annihilation spectroscopy before and after annealing in different environments and at different temperatures. Annealing atmosphere and temperature had significant effects on the PL spectrum, while in all cases the positron diffusion length and PL decay times were increased. We found that, while the defect emission can be significantly reduced by annealing at 200 degrees C, the rods still have large defect concentrations as confirmed by their low positron diffusion length and short PL decay time constants.
Chemical analysis using coincidence Doppler broadening and supporting first-principles theory: Applications to vacancy defects in compound semiconductors

International Nuclear Information System (INIS)

Makkonen, I.; Rauch, C.; Mäki, J.-M.; Tuomisto, F.

2012-01-01

The Doppler broadening of the positron annihilation radiation contains information on the chemical environment of vacancy defects trapping positrons in solids. The measured signal can, for instance, reveal impurity atoms situated next to vacancies. As compared to integrated quantities such as the positron annihilation rate or the annihilation line shape parameters, the full Doppler spectrum measured in the coincidence mode contains much more useful information for defect identification. This information, however, is indirect and complementary understanding is needed to fully interpret the results. First-principles calculations are a valuable tool in the analysis of measured spectra. One can construct an atomic-scale model for a given candidate defect, calculate from first principles the corresponding Doppler spectrum, and directly compare results between experiment and theory. In this paper we discuss recent examples of successful combinations of coincidence Doppler broadening measurements and supporting first-principles calculations. These demonstrate the predictive power of state-of-the-art calculations and the usefulness of such an approach in the chemical analysis of vacancy defects.
A revised method of presenting wavenumber-frequency power spectrum diagrams that reveals the asymmetric nature of tropical large-scale waves

Energy Technology Data Exchange (ETDEWEB)

Chao, Winston C. [NASA/Goddard Space Flight Center, Global Modeling and Assimilation Office, Mail Code 610.1, Greenbelt, MD (United States); Yang, Bo; Fu, Xiouhua [University of Hawaii at Manoa, School of Ocean and Earth Science and Technology, International Pacific Research Center, Honolulu, HI (United States)

2009-11-15

The popular method of presenting wavenumber-frequency power spectrum diagrams for studying tropical large-scale waves in the literature is shown to give an incomplete presentation of these waves. The so-called ''convectively coupled Kelvin (mixed Rossby-gravity) waves'' are presented as existing only in the symmetric (anti-symmetric) component of the diagrams. This is obviously not consistent with the published composite/regression studies of ''convectively coupled Kelvin waves,'' which illustrate the asymmetric nature of these waves. The cause of this inconsistency is revealed in this note and a revised method of presenting the power spectrum diagrams is proposed. When this revised method is used, ''convectively coupled Kelvin waves'' do show anti-symmetric components, and ''convectively coupled mixed Rossby-gravity waves (also known as Yanai waves)'' do show a hint of symmetric components. These results bolster a published proposal that these waves should be called ''chimeric Kelvin waves,'' ''chimeric mixed Rossby-gravity waves,'' etc. This revised method of presenting power spectrum diagrams offers an additional means of comparing the GCM output with observations by calling attention to the capability of GCMs to correctly simulate the asymmetric characteristics of equatorial waves. (orig.)
Moessbauer study of defects in molybdenum and chromium irradiated with ions

International Nuclear Information System (INIS)

Troyan, V.A.; Bogdanov, V.V.; Ivanyushkin, E.M.; Pen'kov, Yu.P.

1980-01-01

Effects of ion irradiation of monocrystalline molybdenum and polycrystalline chromium with Co-57 impurity were studied by Moessbauer effect. Molybdenum specimens were irradiated by He + ions at accelerators with 40 keV energy. Chromium specimens were irradiated by hydrogen ions with 1.2 MeV energy up to integral 2x10 17 -2x10 19 ion/cm 2 doses. It is shown, that defect introduction into the source matrix by irradiation results in change of gamma-resonance line form and effect value. The observed effects of defect influence on spectrum parameters are discussed. It is concluded, that study of Moessbauer spectra parameters of diluted Co-57 solutions in matrices of different metals permits to determine dynamics of movement of impurity atoms and defects in metals irradiated with ions [ru
Analysis of neutron spectrum effects on primary damage in tritium breeding blankets

Energy Technology Data Exchange (ETDEWEB)

Choi, Yong Hee, E-mail: cyh871@snu.ac.kr [School of Energy Systems Engineering, Seoul National University, 599 Gwanak-ro, Gwanak-gu, Seoul 151-744 (Korea, Republic of); Joo, Han Gyu [School of Energy Systems Engineering, Seoul National University, 599 Gwanak-ro, Gwanak-gu, Seoul 151-744 (Korea, Republic of)

2012-07-15

The effect of neutron spectrum on primary damages in a structural material of a tritium breeding blanket is investigated with a newly established recoil spectrum estimation system. First, a recoil spectrum generation code is developed to obtain the energy spectrum of primary knock-on atoms (PKAs) for a given neutron spectrum utilizing the latest ENDF/B data. Secondly, a method for approximating the high energy tail of the recoil spectrum is introduced to avoid expensive molecular dynamics calculations for high energy PKAs using the concept of recoil energy of the secondary knock-on atoms originated by the INtegration of CAScades (INCAS) model. Thirdly, the modified spectrum is combined with a set of molecular dynamics calculation results to estimate the primary damage parameters such as the number of surviving point defects. Finally, the neutron spectrum is varied by changing the material of the spectral shifter and the result in primary damage parameters is examined.
Analysis of neutron spectrum effects on primary damage in tritium breeding blankets

Science.gov (United States)

Choi, Yong Hee; Joo, Han Gyu

2012-07-01

The effect of neutron spectrum on primary damages in a structural material of a tritium breeding blanket is investigated with a newly established recoil spectrum estimation system. First, a recoil spectrum generation code is developed to obtain the energy spectrum of primary knock-on atoms (PKAs) for a given neutron spectrum utilizing the latest ENDF/B data. Secondly, a method for approximating the high energy tail of the recoil spectrum is introduced to avoid expensive molecular dynamics calculations for high energy PKAs using the concept of recoil energy of the secondary knock-on atoms originated by the INtegration of CAScades (INCAS) model. Thirdly, the modified spectrum is combined with a set of molecular dynamics calculation results to estimate the primary damage parameters such as the number of surviving point defects. Finally, the neutron spectrum is varied by changing the material of the spectral shifter and the result in primary damage parameters is examined.
Distribution of defects in wind turbine blades and reliability assessment of blades containing defects

DEFF Research Database (Denmark)

Stensgaard Toft, Henrik; Branner, Kim; Berring, Peter

2009-01-01

on the assumption that one error in the production process tends to trigger several defects. For both models additional information about number, type and size of the defects is included as stochastic variables. The probability of failure for a wind turbine blade will not only depend on variations in the material......In the present paper two stochastic models for the distribution of defects in wind turbine blades are proposed. The first model assumes that the individual defects are completely randomly distributed in the blade. The second model assumes that the defects occur in clusters of different size based...... properties and the load but also on potential defects in the blades. As a numerical example the probability of failure is calculated for the main spar both with and without defects in terms of delaminations. The delaminations increase the probability of failure compared to a perfect blade, but by applying...
Entropy-driven metastable defects in silicon

International Nuclear Information System (INIS)

Hamilton, B.; Peaker, A.R.; Pantelides, S.T.

1989-01-01

The known metastable defects are usually describable by a configuration coordinate diagram in which two energy minima are separated by a barrier. This diagram does not change with temperature and each configuration is stable over some temperature range. Here we report the observation of a novel metastability: A configuration change occurs spontaneously and abruptly at a critical temperature, giving rise to a discontinuous DLTS (deep level transient spectroscopy) spectrum. We propose that this phenomenon is a manifestation of entropy variations in the configurational space. (author) 12 refs., 4 figs
Planck 2013 results. XXV. Searches for cosmic strings and other topological defects

DEFF Research Database (Denmark)

Planck Collaboration,; Ade, P. A. R.; Aghanim, N.

2013-01-01

Planck data have been used to provide stringent new constraints on cosmic strings and other defects. We describe forecasts of the CMB power spectrum induced by cosmic strings, calculating these from network models and simulations using line-of-sight Boltzmann solvers. We have studied Nambu-Goto c...
21 CFR 110.110 - Natural or unavoidable defects in food for human use that present no health hazard.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Natural or unavoidable defects in food for human... PRACTICE IN MANUFACTURING, PACKING, OR HOLDING HUMAN FOOD Defect Action Levels § 110.110 Natural or... natural or unavoidable defects to the lowest level currently feasible. (d) The mixing of a food containing...
Association between cognitive impairments and obsessive-compulsive spectrum presentations following traumatic brain injury.

Science.gov (United States)

Rydon-Grange, Michelle; Coetzer, Rudi

2017-01-02

This study examined the association between self-reported obsessive-compulsive spectrum symptomatology and cognitive performance in a sample of patients with traumatic brain injury (TBI). Twenty-four adults with a moderate-severe TBI accessing a community brain injury rehabilitation service were recruited. Age ranged between 19 and 69 years. Participants completed a battery of neuropsychological tasks assessing memory, executive functioning, and speed of information processing. Self-report questionnaires assessing obsessive-compulsive (OC) symptoms and obsessive-compulsive personality disorder (OCPD) traits were also completed. Correlational analyses revealed that deficits in cognitive flexibility were associated with greater self-reported OC symptomatology and severity. Greater OC symptom severity was significantly related to poorer performance on a visual memory task. Verbal memory and speed of information processing impairments were unrelated to OC symptoms. Performance on tasks of memory, executive functioning, and speed of information processing were not associated with OCPD traits. Overall, results indicate that greater OC symptomatology and severity were associated with specific neuropsychological functions (i.e., cognitive flexibility, visual memory). OCPD personality traits were unrelated to cognitive performance. Further research is needed to examine the potential causal relationship and longer-term interactions between cognitive sequelae and obsessive-compulsive spectrum presentations post-TBI.
Echo detected EPR as a tool for detecting radiation-induced defect signals in pottery

International Nuclear Information System (INIS)

Zoleo, Alfonso; Bortolussi, Claudia; Brustolon, Marina

2011-01-01

Archaeological fragments of pottery have been investigated by using CW-EPR and Echo Detected EPR (EDEPR). EDEPR allows to remove the CW-EPR dominant Fe(III) background spectrum, hiding much weaker signals potentially useful for dating purpose. EDEPR spectra attributed to a methyl radical and to feldspar defects have been recorded at room and low temperature for an Iron Age cooking ware (700 B.C.). A study on the dependence of EDEPR intensity over absorbed dose on a series of γ-irradiated brick samples (estimated age of 562 ± 140 B.C.) has confirmed the potential efficacy of the proposed method for spotting defect signals out of the strong iron background. - Highlights: → Fe(III) CW-EPR signals cover CW-EPR-detectable defects in ceramics. → Echo detected EPR gets rid of Fe(III) signals, disclosing defect signals. → Echo detected EPR detects defect signals even at relatively low doses.
Autism Spectrum Disorder and intact executive functioning.

Science.gov (United States)

Ferrara, R; Ansermet, F; Massoni, F; Petrone, L; Onofri, E; Ricci, P; Archer, T; Ricci, S

2016-01-01

Earliest notions concerning autism (Autism Spectrum Disorders, ASD) describe the disturbance in executive functioning. Despite altered definition, executive functioning, expressed as higher cognitive skills required complex behaviors linked to the prefrontal cortex, are defective in autism. Specific difficulties in children presenting autism or verbal disabilities at executive functioning levels have been identified. Nevertheless, the developmental deficit of executive functioning in autism is highly diversified with huge individual variation and may even be absent. The aim of the present study to examine the current standing of intact executive functioning intact in ASD. Analysis of ASD populations, whether high-functioning, Asperger's or autism Broad Phenotype, studied over a range of executive functions including response inhibition, planning, cognitive flexibility, cognitive inhibition, and alerting networks indicates an absence of damage/impairment compared to the typically-developed normal control subjects. These findings of intact executive functioning in ASD subjects provide a strong foundation on which to construct applications for growth environments and the rehabilitation of autistic subjects.
Point defects in platinum

International Nuclear Information System (INIS)

Piercy, G.R.

1960-01-01

An investigation was made of the mobility and types of point defect introduced in platinum by deformation in liquid nitrogen, quenching into water from 1600 o C, or reactor irradiation at 50 o C. In all cases the activation energy for motion of the defect was determined from measurements of electrical resistivity. Measurements of density, hardness, and x-ray line broadening were also made there applicable. These experiments indicated that the principal defects remaining in platinum after irradiation were single vacant lattice sites and after quenching were pairs of vacant lattice sites. Those present after deformation In liquid nitrogen were single vacant lattice sites and another type of defect, perhaps interstitial atoms. (author)
Defect-mediated photoluminescence up-conversion in cadmium sulfide nanobelts (Conference Presentation)

Science.gov (United States)

Morozov, Yurii; Kuno, Masaru K.

2017-02-01

The concept of optical cooling of solids has existed for nearly 90 years ever since Pringsheim proposed a way to cool solids through the annihilation of phonons via phonon-assisted photoluminescence (PL) up-conversion. In this process, energy is removed from the solid by the emission of photons with energies larger than those of incident photons. However, actually realizing optical cooling requires exacting parameters from the condensed phase medium such as near unity external quantum efficiencies as well as existence of a low background absorption. Until recently, laser cooling has only been successfully realized in rare earth doped solids. In semiconductors, optical cooling has very recently been demonstrated in cadmium sulfide (CdS) nanobelts as well as in hybrid lead halide perovskites. For the former, large internal quantum efficiencies, sub-wavelength thicknesses, which decrease light trapping, and low background absorption, all make near unity external quantum yields possible. Net cooling by as much as 40 K has therefore been possible with CdS nanobelts. In this study, we describe a detailed investigation of the nature of efficient anti-Stokes photoluminescence (ASPL) in CdS nanobelts. Temperature-dependent PL up-conversion and optical absorption studies on individual NBs together with frequency-dependent up-converted PL intensity spectroscopies suggest that ASPL in CdS nanobelts is defect-mediated through involvement of defect levels below the band gap.

Defects and defect processes in nonmetallic solids

CERN Document Server

Hayes, W

2004-01-01

This extensive survey covers defects in nonmetals, emphasizing point defects and point-defect processes. It encompasses electronic, vibrational, and optical properties of defective solids, plus dislocations and grain boundaries. 1985 edition.
Characterization of the structure and chemistry of defects in materials

International Nuclear Information System (INIS)

Larson, B.C.; Ruehle, M.; Seidman, D.N.

1988-01-01

Research programs, presented at the materials research symposium, on defects in materials are presented. Major areas include: point defects, defect aggregates, and ordering; defects in non-metals and semiconductors; atomic resolution imaging of defects; and gain boundaries, interfaces, and layered materials. Individual projects are processed separately for the data bases
Electronic properties of graphene with single vacancy and Stone-Wales defects

International Nuclear Information System (INIS)

Zaminpayma, Esmaeil; Razavi, Mohsen Emami; Nayebi, Payman

2017-01-01

Highlights: • The electronic properties of graphene device with single vacancy (SV) and Stone-Wales (SW) defect have been studied. • The first principles calculations have been performed based on self-consistent charge density functional tight-binding. • The density of state, current voltage curves of pure graphene and graphene with SV and SW defects have been investigated. • Transmission spectrum of pristine graphene device and graphene with SV and SW defects has been examined. - Abstract: The first principles calculations have been performed based on self-consistent charge density functional tight-binding in order to examine the electronic properties of graphene with single vacancy (SV) and Stone-Wales (SW) defects. We have optimized structures of pristine graphene and graphene with SV and SW defects. The bond lengths, current-voltage curve and transmission probability have been calculated. We found that the bond length for relaxed graphene is 1.43 Å while for graphene with SV and SW defects the bond lengths are 1.41 Å and 1.33 Å, respectively. For the SV defect, the arrangement of atoms with three nearest neighbors indicates sp_2 bonding. While for SW defect, the arrangement of atoms suggests nearly sp bonding. From the current-voltage curve for graphene with defects we have determined that the behavior of the I–V curves is nonlinear. It is also found that the SV and SW defects cause to decrease the current compared to the pristine graphene case. Furthermore, the single vacancy defect reduces the current more than the Stone-Wales defect. Moreover, we observed that by increasing the voltage from zero to 1 V new peaks near Fermi level in the transmission probability curves have been created.
Electronic properties of graphene with single vacancy and Stone-Wales defects

Energy Technology Data Exchange (ETDEWEB)

Zaminpayma, Esmaeil [Physics Group, Qazvin Branch, Islamic Azad University, Qazvin (Iran, Islamic Republic of); Razavi, Mohsen Emami, E-mail: razavi246@gmail.com [Plasma Physics Research Center, Science and Research Branch, Islamic Azad University, P.O. Box 14665-678, Tehran (Iran, Islamic Republic of); Nayebi, Payman [Department of Physics, College of Technical and Engineering, Saveh Branch, Islamic Azad University, Saveh (Iran, Islamic Republic of)

2017-08-31

Highlights: • The electronic properties of graphene device with single vacancy (SV) and Stone-Wales (SW) defect have been studied. • The first principles calculations have been performed based on self-consistent charge density functional tight-binding. • The density of state, current voltage curves of pure graphene and graphene with SV and SW defects have been investigated. • Transmission spectrum of pristine graphene device and graphene with SV and SW defects has been examined. - Abstract: The first principles calculations have been performed based on self-consistent charge density functional tight-binding in order to examine the electronic properties of graphene with single vacancy (SV) and Stone-Wales (SW) defects. We have optimized structures of pristine graphene and graphene with SV and SW defects. The bond lengths, current-voltage curve and transmission probability have been calculated. We found that the bond length for relaxed graphene is 1.43 Å while for graphene with SV and SW defects the bond lengths are 1.41 Å and 1.33 Å, respectively. For the SV defect, the arrangement of atoms with three nearest neighbors indicates sp{sub 2} bonding. While for SW defect, the arrangement of atoms suggests nearly sp bonding. From the current-voltage curve for graphene with defects we have determined that the behavior of the I–V curves is nonlinear. It is also found that the SV and SW defects cause to decrease the current compared to the pristine graphene case. Furthermore, the single vacancy defect reduces the current more than the Stone-Wales defect. Moreover, we observed that by increasing the voltage from zero to 1 V new peaks near Fermi level in the transmission probability curves have been created.
Diving into the world of alcohol teratogenesis: a review of zebrafish models of fetal alcohol spectrum disorder.

Science.gov (United States)

Fernandes, Yohaan; Buckley, Desire M; Eberhart, Johann K

2018-04-01

The term fetal alcohol spectrum disorder (FASD) refers to the entire suite of deleterious outcomes resulting from embryonic exposure to alcohol. Along with other reviews in this special issue, we provide insight into how animal models, specifically the zebrafish, have informed our understanding of FASD. We first provide a brief introduction to FASD. We discuss the zebrafish as a model organism and its strengths for alcohol research. We detail how zebrafish has been used to model some of the major defects present in FASD. These include behavioral defects, such as social behavior as well as learning and memory, and structural defects, disrupting organs such as the brain, sensory organs, heart, and craniofacial skeleton. We provide insights into how zebrafish research has aided in our understanding of the mechanisms of ethanol teratogenesis. We end by providing some relatively recent advances that zebrafish has provided in characterizing gene-ethanol interactions that may underlie FASD.
Characterizing the Peak in the Cosmic Microwave Background Angular Power Spectrum

International Nuclear Information System (INIS)

Knox, Lloyd; Page, Lyman

2000-01-01

A peak has been unambiguously detected in the cosmic microwave background angular spectrum. Here we characterize its properties with fits to phenomenological models. We find that the TOCO and BOOM/NA data determine the peak location to be in the range 175-243 and 151-259, respectively (at 95% confidence) and determine the peak amplitude to be between ≅70 and 90 μK . The peak shape is consistent with inflation-inspired flat, cold dark matter plus cosmological constant models of structure formation with adiabatic, nearly scale invariant initial conditions. It is inconsistent with open models and presents a great challenge to defect models. (c) 2000 The American Physical Society
Areva solutions for management of defective fuel

International Nuclear Information System (INIS)

Morlaes, I.; Vo Van, V.

2014-01-01

Defective fuel management is a major challenge for nuclear operators when all fuel must be long-term managed. This paper describes AREVA solutions for managing defective fuel. Transport AREVA performs shipments of defective fuel in Europe and proposes casks that are licensed for that purpose in Europe and in the USA. The paper presents the transport experience and the new European licensing approach of defective fuel transport. Dry Interim Storage AREVA is implementing the defective fuel storage in the USA, compliant with the Safety Authority's requirements. In Europe, AREVA is developing a new, more long-term oriented storage solution for defective fuel, the best available technology regarding safety requirements. The paper describes these storage solutions. Treatment Various types of defective fuel coming from around the world have been treated in the AREVA La Hague plant. Specific treatment procedures were developed when needed. The paper presents operational elements related to this experience. (authors)
Channelopathy Pathogenesis in Autism Spectrum Disorders

Directory of Open Access Journals (Sweden)

Galina eSchmunk

2013-11-01

Full Text Available Autism spectrum disorder (ASD is a syndrome that affects normal brain development and is characterized by impaired social interaction as well as verbal and non-verbal communication and by repetitive, stereotypic behavior. ASD is a complex disorder arising from a combination of multiple genetic and environmental factors that are independent from racial, ethnic and socioeconomical status. The high heritability of ASD suggests a strong genetic basis for the disorder. Furthermore, a mounting body of evidence implies a role of various ion channel gene defects (channelopathies in the pathogenesis of autism. Indeed, recent genome-wide association, and whole exome- and whole- genome resequencing studies linked polymorphisms and rare variants in calcium, sodium and potassium channels and their subunits with susceptibility to ASD, much as they do with bipolar disorder, schizophrenia and other neuropsychiatric disorders, and animal models with these genetic variations recapitulate endophenotypes considered to be correlates of autistic behavior seen in patients. An ion flux across the membrane regulates a variety of cell functions, from generation of action potentials to gene expression and cell morphology, thus it is not surprising that channelopathies have profound effects on brain functions. In the present work, we summarize existing evidence for the role of ion channel gene defects in the pathogenesis of autism with a focus on calcium signaling and its downstream effects.
Visual Defects in a Mouse Model of Fetal Alcohol Spectrum Disorder

OpenAIRE

Lantz, Crystal L.; Pulimood, Nisha S.; Rodrigues-Junior, Wandilson S.; Chen, Ching-Kang; Manhaes, Alex C.; Kalatsky, Valery A.; Medina, Alexandre Esteves

2014-01-01

Alcohol consumption during pregnancy can lead to a multitude of neurological problems in offspring, varying from subtle behavioral changes to severe mental retardation. These alterations are collectively referred to as Fetal Alcohol Spectrum Disorders (FASD). Early alcohol exposure can strongly affect the visual system and children with FASD can exhibit an amblyopia-like pattern of visual acuity deficits even in the absence of optical and oculomotor disruption. Here, we test whether early alc...
Model of defect reactions and the influence of clustering in pulse-neutron-irradiated Si

International Nuclear Information System (INIS)

Myers, S. M.; Cooper, P. J.; Wampler, W. R.

2008-01-01

Transient reactions among irradiation defects, dopants, impurities, and carriers in pulse-neutron-irradiated Si were modeled taking into account the clustering of the primal defects in recoil cascades. Continuum equations describing the diffusion, field drift, and reactions of relevant species were numerically solved for a submicrometer spherical volume, within which the starting radial distributions of defects could be varied in accord with the degree of clustering. The radial profiles corresponding to neutron irradiation were chosen through pair-correlation-function analysis of vacancy and interstitial distributions obtained from the binary-collision code MARLOWE, using a spectrum of primary recoil energies computed for a fast-burst fission reactor. Model predictions of transient behavior were compared with a variety of experimental results from irradiated bulk Si, solar cells, and bipolar-junction transistors. The influence of defect clustering during neutron bombardment was further distinguished through contrast with electron irradiation, where the primal point defects are more uniformly dispersed
Who named the quantum defect?

International Nuclear Information System (INIS)

Rau, A.R.P.; Inokuti, M.

1997-01-01

The notion of the quantum defect is important in atomic and molecular spectroscopy and also in unifying spectroscopy with collision theory. In the latter context, the quantum defect may be viewed as an ancestor of the phase shift. However, the origin of the term quantum defect does not seem to be explained in standard textbooks. It occurred in a 1921 paper by Schroedinger, preceding quantum mechanics, yet giving the correct meaning as an index of the short-range interactions with the core of an atom. The authors present the early history of the quantum-defect idea, and sketch its recent developments
Self-Presentation and the Role of Perspective Taking and Social Motivation in Autism Spectrum Disorder.

Science.gov (United States)

Scheeren, Anke M; Banerjee, Robin; Koot, Hans M; Begeer, Sander

2016-02-01

We compared self-presentation abilities of 132 children and adolescents with autism spectrum disorders (ASD) to those of 41 typically developing (TD) peers, and examined the potential link with their social motivation and perspective taking. Participants introduced themselves to an interviewer in a baseline condition (without incentive) and a self-promotion condition (with incentive). Children with ASD (6-12 years) were just as likely as or even more likely than TD children to highlight personal characteristics that would increase their chances of obtaining the incentive. Thus, they were strategic in their self-presentation. However, adolescents with ASD (12-19 years) were less strategic than TD adolescents as well as children with ASD. We discuss the role of social motivation and perspective taking in children's self-presentation.
Defects at oxide surfaces

CERN Document Server

Thornton, Geoff

2015-01-01

This book presents the basics and characterization of defects at oxide surfaces. It provides a state-of-the-art review of the field, containing information to the various types of surface defects, describes analytical methods to study defects, their chemical activity and the catalytic reactivity of oxides. Numerical simulations of defective structures complete the picture developed. Defects on planar surfaces form the focus of much of the book, although the investigation of powder samples also form an important part. The experimental study of planar surfaces opens the possibility of applying the large armoury of techniques that have been developed over the last half-century to study surfaces in ultra-high vacuum. This enables the acquisition of atomic level data under well-controlled conditions, providing a stringent test of theoretical methods. The latter can then be more reliably applied to systems such as nanoparticles for which accurate methods of characterization of structure and electronic properties ha...
Photoionization spectroscopy of deep defects responsible for current collapse in nitride-based field effect transistors

International Nuclear Information System (INIS)

Klein, P B; Binari, S C

2003-01-01

This review is concerned with the characterization and identification of the deep centres that cause current collapse in nitride-based field effect transistors. Photoionization spectroscopy is an optical technique that has been developed to probe the characteristics of these defects. Measured spectral dependences provide information on trap depth, lattice coupling and on the location of the defects in the device structure. The spectrum of an individual trap may also be regarded as a 'fingerprint' of the defect, allowing the trap to be followed in response to the variation of external parameters. The basis for these measurements is derived through a modelling procedure that accounts quantitatively for the light-induced drain current increase in the collapsed device. Applying the model to fit the measured variation of drain current increase with light illumination provides an estimate of the concentrations and photoionization cross-sections of the deep defects. The results of photoionization studies of GaN metal-semiconductor field effect transistors and AlGaN/GaN high electron mobility transistors (HEMTs) grown by metal-organic chemical vapour deposition (MOCVD) are presented and the conclusions regarding the nature of the deep traps responsible are discussed. Finally, recent photoionization studies of current collapse induced by short-term (several hours) bias stress in AlGaN/GaN HEMTs are described and analysed for devices grown by both MOCVD and molecular beam epitaxy. (topical review)
Three-dimensional transesophageal echocardiography of the atrial septal defects

Directory of Open Access Journals (Sweden)

Romero-Cárdenas Ángel

2008-07-01

Full Text Available Abstract Transesophageal echocardiography has advantages over transthoracic technique in defining morphology of atrial structures. Even though real time three-dimensional echocardiographic imaging is a reality, the off-line reconstruction technique usually allows to obtain higher spatial resolution images. The purpose of this study was to explore the accuracy of off-line three-dimensional transesophageal echocardiography in a spectrum of atrial septal defects by comparing them with representative anatomic specimens.
In-situ volumetric topography of IC chips for defect detection using infrared confocal measurement with active structured light

International Nuclear Information System (INIS)

Chen, Liang-Chia; Le, Manh-Trung; Phuc, Dao Cong; Lin, Shyh-Tsong

2014-01-01

The article presents the development of in-situ integrated circuit (IC) chip defect detection techniques for automated clipping detection by proposing infrared imaging and full-field volumetric topography. IC chip inspection, especially held during or post IC packaging, has become an extremely critical procedure in IC fabrication to assure manufacturing quality and reduce production costs. To address this, in the article, microscopic infrared imaging using an electromagnetic light spectrum that ranges from 0.9 to 1.7 µm is developed to perform volumetric inspection of IC chips, in order to identify important defects such as silicon clipping, cracking or peeling. The main difficulty of infrared (IR) volumetric imaging lies in its poor image contrast, which makes it incapable of achieving reliable inspection, as infrared imaging is sensitive to temperature difference but insensitive to geometric variance of materials, resulting in difficulty detecting and quantifying defects precisely. To overcome this, 3D volumetric topography based on 3D infrared confocal measurement with active structured light, as well as light refractive matching principles, is developed to detect defects the size, shape and position of defects in ICs. The experimental results show that the algorithm is effective and suitable for in-situ defect detection of IC semiconductor packaging. The quality of defect detection, such as measurement repeatability and accuracy, is addressed. Confirmed by the experimental results, the depth measurement resolution can reach up to 0.3 µm, and the depth measurement uncertainty with one standard deviation was verified to be less than 1.0% of the full-scale depth-measuring range. (paper)
Metastable gravity on classical defects

International Nuclear Information System (INIS)

Ringeval, Christophe; Rombouts, Jan-Willem

2005-01-01

We discuss the realization of metastable gravity on classical defects in infinite-volume extra dimensions. In dilatonic Einstein gravity, it is found that the existence of metastable gravity on the defect core requires violation of the dominant energy condition for codimension N c =2 defects. This is illustrated with a detailed analysis of a six-dimensional hyperstring minimally coupled to dilaton gravity. We present the general conditions under which a codimension N c >2 defect admits metastable modes, and find that they differ from lower codimensional models in that, under certain conditions, they do not require violation of energy conditions to support quasilocalized gravity
Human diseases associated with defective DNA repair

International Nuclear Information System (INIS)

Friedberg, E.C.; Ehmann, U.K.; Williams, J.I.

1979-01-01

The observations on xeroderma pigmentosum (XP) cells in culture were the first indications of defective DNA repair in association with human disease. Since then, a wealth of information on DNA repair in XP, and to a lesser extent in other diseases, has accumulated in the literature. Rather than clarifying the understanding of DNA repair mechanisms in normal cells and of defective DNA repair in human disease, the literature suggests an extraordinary complexity of both of the phenomena. In this review a number of discrete human diseases are considered separately. An attempt was made to systematically describe the pertinent clinical features and cellular and biochemical defects in these diseases, with an emphasis on defects in DNA metabolism, particularly DNA repair. Wherever possible observations have been correlated and unifying hypotheses presented concerning the nature of the basic defect(s) in these diseases. Discussions of the following diseases are presented: XP, ataxia telangiectasia; Fanconi's anemia; Hutchinson-Gilford progeria syndrome; Bloom's syndrome, Cockayne's syndrome; Down's syndrome; retinoblastoma; chronic lymphocytic leukemia; and other miscellaneous human diseases with possble DNA repair defects
Determination of defect content and defect profile in semiconductor heterostructures

International Nuclear Information System (INIS)

Zubiaga, A; Garcia, J A; Plazaola, F; Zuniga-Perez, J; Munoz-Sanjose, V

2011-01-01

In this article we present an overview of the technique to obtain the defects depth profile and width of a deposited layer and multilayer based on positron annihilation spectroscopy. In particular we apply the method to ZnO and ZnO/ZnCdO layers deposited on sapphire substrates. After introducing some terminology we first calculate the trend that the W/S parameters of the Doppler broadening measurements must follow, both in a qualitative and quantitative way. From this point we extend the results to calculate the width and defect profiles in deposited layer samples.
Determination of defect content and defect profile in semiconductor heterostructures

Energy Technology Data Exchange (ETDEWEB)

Zubiaga, A [Laboratory of Physics, HUT, PO Box 1100, 02015 TKK, Espoo (Finland); Garcia, J A; Plazaola, F [Zientzia eta Teknologia Fakultatea, Euskal Herriko Unbertsitatea, P. K. 644, 48080, Bilbao (Spain); Zuniga-Perez, J; Munoz-Sanjose, V, E-mail: fernando.plazaola@ehu.es [Universitat de Valencia, Departamento de Fisica Aplicada i Electromagnetisme, Dr. Moliner 50, 46100 Burjassot, Valencia (Spain)

2011-01-10

In this article we present an overview of the technique to obtain the defects depth profile and width of a deposited layer and multilayer based on positron annihilation spectroscopy. In particular we apply the method to ZnO and ZnO/ZnCdO layers deposited on sapphire substrates. After introducing some terminology we first calculate the trend that the W/S parameters of the Doppler broadening measurements must follow, both in a qualitative and quantitative way. From this point we extend the results to calculate the width and defect profiles in deposited layer samples.

Defect physics and electronic properties of Cu3PSe4 from first principles

Science.gov (United States)

Foster, D. H.; Barras, F. L.; Vielma, J. M.; Schneider, G.

2013-11-01

The p-type semiconductor Cu3PSe4 has recently been established to have a direct band gap of 1.4 eV and an optical absorption spectrum similar to GaAs [Foster , Appl. Phys. Lett.APPLAB0003-695110.1063/1.3656760 99, 181903 (2011)], suggesting a possible application as a solar photovoltaic absorber. Here we calculate the thermodynamic stability, defect energies and concentrations, and several material properties of Cu3PSe4 using a wholly GGA+U method (the generalized gradient approximation of density functional theory with a Hubbard U term included for the Cu-d orbitals). We find that two low energy acceptor defects, the copper vacancy VCu and the phosphorus-on-selenium antisite PSe, establish the p-type behavior and likely prevent any n-type doping near thermal equilibrium. The GGA+U defect calculation method is shown to yield more accurate results than the more standard method of applying post-calculation GGA+U-based band-gap corrections to strictly GGA defect calculations.
Neuromyelitis optica spectrum disorder presenting with repeated hypersomnia due to involvement of the hypothalamus and hypothalamus-amygdala linkage.

Science.gov (United States)

Kume, Kodai; Deguchi, Kazushi; Ikeda, Kazuyo; Takata, Tadayuki; Kokudo, Yohei; Kamada, Masaki; Touge, Tetsuo; Takahashi, Toshiyuki; Kanbayashi, Takashi; Masaki, Tsutomu

2015-06-01

We report the case of a 46-year-old Japanese woman with neuromyelitis optica spectrum disorder presenting with repeated hypersomnia accompanied by decreased CSF orexin level. First episode associated with hypothalamic-pituitary dysfunction showed bilateral hypothalamic lesions that can cause secondary damage to the orexin neurons. The second episode associated with impaired memory showed a left temporal lesion involving the amygdala. The mechanism remains unknown, but the reduced blood flow in the hypothalamus ipsilateral to the amygdala lesion suggested trans-synaptic hypothalamic dysfunction secondary to the impaired amygdala. A temporal lesion involving the amygdala and hypothalamus could be responsible for hypersomnia due to neuromyelitis optica spectrum disorder. © The Author(s), 2015.
The influence of coordinated defects on inhomogeneous broadening in cubic lattices

Energy Technology Data Exchange (ETDEWEB)

Matheson, P. L., E-mail: phil.matheson@uvu.edu; Sullivan, Francis P.; Evenson, William E. [Utah Valley University, Department of Physics (United States)

2016-12-15

The joint probability distribution function (JPDF) of electric field gradient (EFG) tensor components in cubic materials is dominated by coordinated pairings of defects in shells near probe nuclei. The contributions from these inner shell combinations and their surrounding structures contain the essential physics that determine the PAC-relevant quantities derived from them. The JPDF can be used to predict the nature of inhomogeneous broadening (IHB) in perturbed angular correlation (PAC) experiments by modeling the G{sub 2} spectrum and finding expectation values for V{sub zz} and η. The ease with which this can be done depends upon the representation of the JPDF. Expanding on an earlier work by Czjzek et al. (Hyperfine Interact. 14, 189–194, 1983), Evenson et al. (Hyperfine Interact. 237, 119, 2016) provide a set of coordinates constructed from the EFG tensor invariants they named W{sub 1} and W{sub 2}. Using this parameterization, the JPDF in cubic structures was constructed using a point charge model in which a single trapped defect (TD) is the nearest neighbor to a probe nucleus. Individual defects on nearby lattice sites pair with the TD to provide a locus of points in the W{sub 1}−W{sub 2} plane around which an amorphous-like distribution of probability density grows. Interestingly, however, marginal, separable PDFs appear adequate to model IHB relevant cases. We present cases from simulations in cubic materials illustrating the importance of these near-shell coordinations.
Destruction-polymerization transformations as a source of radiation-induced extended defects in chalcogenide glassy semiconductors

International Nuclear Information System (INIS)

Shpotyuk, Oleh; Filipecki, Jacek; Shpotyuk, Mykhaylo

2013-01-01

Long-wave shift of the optical transmission spectrum in the region of fundamental optical absorption edge is registered for As 2 S 3 chalcogenide glassy semiconductors after γ-irradiation. This effect is explained in the frameworks of the destruction-polymerization transformations concept by accepting the switching of the heteropolar As-S covalent bonds into homopolar As-As ones. It is assumed that (As 4 + ; S 1 - ) defect pairs are created under such switching. Formula to calculate content of the induced defects in chalcogenide glassy semiconductors is proposed. It is assumed that defects concentration depends on energy of broken covalent bond, bond-switching energy balance, correlation energy, optical band-gap and energy of excitation light. It is shown that theoretically calculated maximally possible content of radiation-induced defects in As 2 S 3 is about 1.6% while concentration of native defects is negligible. (copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)
Disc defect classification for optical disc drives

NARCIS (Netherlands)

Helvoirt, van J.; Leenknegt, G.A.L.; Steinbuch, M.; Goossens, H.J.

2005-01-01

Optical disc drives are subject to various disturbances and faults. A special type of fault is the so-called disc defect. In this paper we present an approach for disc defect classification. It is based on hierarchical clustering of measured signals that are affected by disc defects. The
Microstructural evolution of pure tungsten neutron irradiated with a mixed energy spectrum

Energy Technology Data Exchange (ETDEWEB)

Koyanagi, Takaaki, E-mail: koyanagit@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Kumar, N.A.P. Kiran [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Hwang, Taehyun [Tohoku University, Sendai, 980-8579 (Japan); Garrison, Lauren M.; Hu, Xunxiang [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Snead, Lance L. [Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Katoh, Yutai [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

2017-07-15

Microstructures of single-crystal bulk tungsten (W) and polycrystalline W foil with a strong grain texture were investigated using transmission electron microscopy following neutron irradiation at ∼90–800 °C to 0.03–4.6 displacements per atom (dpa) in the High Flux Isotope Reactor with a mixed energy spectrum. The dominant irradiation defects were dislocation loops and small clusters at ∼90 °C. Additional voids were formed in W irradiated at above 460 °C. Voids and precipitates involving transmutation rhenium and osmium were the dominant defects at more than ∼1 dpa. We found a new phenomenon of microstructural evolution in irradiated polycrystalline W: Re- and Os-rich precipitation along grain boundaries. Comparison of results between this study and previous studies using different irradiation facilities revealed that the microstructural evolution of pure W is highly dependent on the neutron energy spectrum in addition to the irradiation temperature and dose.
Electronic structure of point defects in semiconductors

International Nuclear Information System (INIS)

Bruneval, Fabien

2014-01-01

This 'Habilitation a diriger des Recherches' memoir presents most of my scientific activities during the past 7 years, in the field of electronic structure calculations of defects in solids. Point defects (vacancies, interstitials, impurities) in functional materials are a key parameter to determine if these materials will actually fill the role they have been assigned or not. Indeed, the presence of defects cannot be avoided when the temperature is increased or when the material is subjected to external stresses, such as irradiation in the nuclear reactors and in artificial satellites with solar radiations. However, in many cases, defects are introduced in the materials on purpose to tune the electronic transport, optical or even magnetic properties. This procedure is called the doping of semiconductors, which is the foundation technique for transistors, diodes, or photovoltaic cells. However, doping is not always straightforward and unexpected features may occur, such as doping asymmetry or Fermi level pinning, which can only be explained by complex phenomena involving different types of defects or complexes of defects. In this context, the calculations of electronic structure ab initio is an ideal tool to complement the experimental observations, to gain the understanding of phenomena at the atomic level, and even to predict the properties of defects. The power of the ab initio calculations comes from their ability to describe any system of electrons and nuclei without any specific adjustment. But although there is a strong need for numerical simulations in this field, the ab initio calculations for defects are still under development as of today. The work presented in this memoir summarizes my contributions to methodological developments on this subject. These developments have followed two main tracks. The first topic is the better understanding of the unavoidable finite size effects. Indeed, defects in semiconductors or insulators are generally present in
Neural Correlates of Reflection on Present and Past Selves in Autism Spectrum Disorder.

Science.gov (United States)

Cygan, Hanna B; Marchewka, Artur; Kotlewska, Ilona; Nowicka, Anna

2018-06-05

Previous studies indicate that autobiographical memory is impaired in individuals with autism spectrum disorder (ASD). Successful recollection of information referring to one's own person requires the intact ability to re-activate representation of the past self. In the current fMRI study we investigated process of conscious reflection on the present self, the past self, and a close-other in the ASD and typically developing groups. Significant inter-group differences were found in the Past-Self condition. In individuals with ASD, reflection on the past self was associated with additional engagement of the posterior cingulate and posterior temporal structures. We hypothesize that this enhanced activation of widely distributed neural network reflects substantial difficulties in processes of reflection on one's own person in the past.
Ultrasonic defect detection method for socket welding joint

International Nuclear Information System (INIS)

Tominaga, Masaaki; Matsuo, Toshiyuki; Ueno, Akihiro; Watanabe, Kunimichi; Kawamata, Kunio.

1995-01-01

The present invention provides a method of detecting defects over a wide range of a socket weld portion of various kinds of pipelines used, for example, in a nuclear power plant. Namely, an inclined probe is disposed to a jig for detecting defects by ultrasonic waves. This is rotated at least by one turn along the peripheral surface of the material to be detected such as weld tube joints. Defects of weld portion of the material can be detected automatically by using ultrasonic waves during the rotation. The inclined probe for detecting defects by ultrasonic waves comprises a transmission portion having a planar transmittance oscillator disposed to a wedge on the transmission side and a receiving portion comprising a planar receiving oscillator disposed to a wedge on the receiving side. With such a constitution, ultrasonic waves are emitted from the transmission portion to the defect detection portion in the welded portion. If a defect is present, defective echo is reflected to the receiving portion disposed ahead of the probe. Since the defective echo changes depending on the height of the detective portion, the estimation of the height of the defect can be facilitated. (I.S.)
Treatment of autistic spectrum disorder with insulin-like growth factors.

Science.gov (United States)

Riikonen, Raili

2016-11-01

There are no treatments for the core symptoms of autistic spectrum disorder (ASD), but there is now more knowledge on emerging mechanisms and on mechanism-based therapies. In autism there are altered synapses: genes affected are commonly related to synaptic and immune function. Dysregulation of activity-dependent signaling networks may have a key role the etiology of autism. There is an over-activation of IGF-AKT-mTor in autism spectrum disorders. Morphological and electro-physiological defects of the cerebellum are linked to system-wide ASD-like behavior defects. The molecular basis for a cerebellar contribution has been demonstrated in a mouse model. These have led to a potential mechanism-based use of drug targets and mouse models. Neurotrophic factors are potential candidates for the treatment. Insulin-like growth factor-1 (IGF-1) is altered in autism. It reduces neuro-inflammation: by causing changes of cytokines such as IL-6 and microglial function. IGF-1 reduces the defects in the synapse. It alleviates NMDA-induced neurotoxicity via the IGF-AKT-mTor pathway in microglia. IGF-1 may rescue function in Rett syndrome and ASD caused by changes of the SCHANK3 gene. There are recently pilot studies of the treatment of Rett syndrome and of SCHANK3 gene deficiency syndromes. The FDA has granted Orphan drug designations for Fragile X syndrome, SCHANK3 gene deficiency syndrome and Rett syndrome. Copyright © 2016 European Paediatric Neurology Society. Published by Elsevier Ltd. All rights reserved.
Induced defects in neutron irradiated GaN single crystals

International Nuclear Information System (INIS)

Park, I. W.; Koh, E. K.; Kim, Y. M.; Choh, S. H.; Park, S. S.; Kim, B. G.; Sohn, J. M.

2005-01-01

The local structure of defects in undoped, Si-doped, and neutron irradiated free standing GaN bulk crystals, grown by hydride vapor phase epitaxy, has been investigated by employing Raman scattering and cathodoluminescence. The GaN samples were irradiated to a dose of 2 x 10 17 neutrons in an atomic reactor at Korea Atomic Energy Research Institute. There was no appreciable change in the Raman spectra for undoped GaN samples before and after neutron irradiation. However, a forbidden transition, A 1 (TO) mode, appeared for a neutron irradiated Si-doped GaN crystal. Cathodoluminescence spectrum for the neutron irradiated Si-doped GaN crystal became much more broadened than that for the unirradiated one. The experimental results reveal the generation of defects with locally deformed structure in the wurtzite Si-doped GaN single crystal
Fast radio burst search: cross spectrum vs. auto spectrum method

Science.gov (United States)

Liu, Lei; Zheng, Weimin; Yan, Zhen; Zhang, Juan

2018-06-01

The search for fast radio bursts (FRBs) is a hot topic in current radio astronomy studies. In this work, we carry out a single pulse search with a very long baseline interferometry (VLBI) pulsar observation data set using both auto spectrum and cross spectrum search methods. The cross spectrum method, first proposed in Liu et al., maximizes the signal power by fully utilizing the fringe phase information of the baseline cross spectrum. The auto spectrum search method is based on the popular pulsar software package PRESTO, which extracts single pulses from the auto spectrum of each station. According to our comparison, the cross spectrum method is able to enhance the signal power and therefore extract single pulses from data contaminated by high levels of radio frequency interference (RFI), which makes it possible to carry out a search for FRBs in regular VLBI observations when RFI is present.
Multiscale crystal defect dynamics: A coarse-grained lattice defect model based on crystal microstructure

Science.gov (United States)

Lyu, Dandan; Li, Shaofan

2017-10-01

Crystal defects have microstructure, and this microstructure should be related to the microstructure of the original crystal. Hence each type of crystals may have similar defects due to the same failure mechanism originated from the same microstructure, if they are under the same loading conditions. In this work, we propose a multiscale crystal defect dynamics (MCDD) model that models defects by considering its intrinsic microstructure derived from the microstructure or material genome of the original perfect crystal. The main novelties of present work are: (1) the discrete exterior calculus and algebraic topology theory are used to construct a scale-up (coarse-grained) dual lattice model for crystal defects, which may represent all possible defect modes inside a crystal; (2) a higher order Cauchy-Born rule (up to the fourth order) is adopted to construct atomistic-informed constitutive relations for various defect process zones, and (3) an hierarchical strain gradient theory based finite element formulation is developed to support an hierarchical multiscale cohesive (process) zone model for various defects in a unified formulation. The efficiency of MCDD computational algorithm allows us to simulate dynamic defect evolution at large scale while taking into account atomistic interaction. The MCDD model has been validated by comparing of the results of MCDD simulations with that of molecular dynamics (MD) in the cases of nanoindentation and uniaxial tension. Numerical simulations have shown that MCDD model can predict dislocation nucleation induced instability and inelastic deformation, and thus it may provide an alternative solution to study crystal plasticity.
Defect identification using positrons

International Nuclear Information System (INIS)

Beling, C.D.; Fung, S.

2001-01-01

The current use of the lifetime and Doppler broadening techniques in defect identification is demonstrated with two studies, the first being the identification of carbon vacancy in n-6H SiC through lifetime spectroscopy, and the second the production of de-hydrogenated voids in α-Si:H through light soaking. Some less conventional ideas are presented for more specific defect identification, namely (i) the amalgamation of lifetime and Doppler techniques with conventional deep level transient spectroscopy in what may be called ''positron-deep level transient spectroscopy'', and (ii) the extraction of more spatial information on vacancy defects by means of what may be called ''Fourier transform Doppler broadening of annihilation radiation spectroscopy'' (orig.)
Congenital tracheal defects: embryonic development and animal models

Directory of Open Access Journals (Sweden)

Zenab Arooj Sher

2016-03-01

Full Text Available Tracheal anomalies are potentially catastrophic congenital defects. As a newborn begins to breathe, the trachea needs to maintain an appropriate balance of elasticity and rigidity. If the tracheal cartilages are disorganized or structurally weak, the airways can collapse, obstructing breathing. Cartilage rings that are too small or too rigid can also obstruct breathing. These anomalies are frequently associated with craniofacial syndromes, and, despite the importance, are poorly understood. In this review, we summarize the spectrum of pathological phenotypes of the trachea and correlate them with the molecular events uncovered in mouse models.
Defect properties from X-ray scattering experiments

International Nuclear Information System (INIS)

Peisl, H.

1976-01-01

Lattice distortions due to defects in crystals can be studied most directly by elastic X-ray or neutron scattering experiments. The 'size' of the defects can be determined from the shift of the Bragg reflections. Defect induced diffuse scattering intensity close to and between Bragg reflections gives information on the strength and symmetry of the distortion fields and yields the atomic structure of point defects (interstitials, vacancies, small aggregates). Diffuse scattering is a very sensitive method to decide whether defects are present as isolated point defects or have formed aggregates. X-ray scattering has been used to study defects produced in various ionic crystals by γ- and neutron irradiation. After an introduction to the principles of the method the experimental results will be reviewed and discussed in some detail. (orig.) [de
ILT based defect simulation of inspection images accurately predicts mask defect printability on wafer

Science.gov (United States)

Deep, Prakash; Paninjath, Sankaranarayanan; Pereira, Mark; Buck, Peter

2016-05-01

printability of defects at wafer level and automates the process of defect dispositioning from images captured using high resolution inspection machine. It first eliminates false defects due to registration, focus errors, image capture errors and random noise caused during inspection. For the remaining real defects, actual mask-like contours are generated using the Calibre® ILT solution [1][2], which is enhanced to predict the actual mask contours from high resolution defect images. It enables accurate prediction of defect contours, which is not possible from images captured using inspection machine because some information is already lost due to optical effects. Calibre's simulation engine is used to generate images at wafer level using scanner optical conditions and mask-like contours as input. The tool then analyses simulated images and predicts defect printability. It automatically calculates maximum CD variation and decides which defects are severe to affect patterns on wafer. In this paper, we assess the printability of defects for the mask of advanced technology nodes. In particular, we will compare the recovered mask contours with contours extracted from SEM image of the mask and compare simulation results with AIMSTM for a variety of defects and patterns. The results of printability assessment and the accuracy of comparison are presented in this paper. We also suggest how this method can be extended to predict printability of defects identified on EUV photomasks.
Neutron diffraction and lattice defects

International Nuclear Information System (INIS)

Hamaguchi, Yoshikazu

1974-01-01

Study on lattice defects by neutron diffraction technique is described. Wave length of neutron wave is longer than that of X-ray, and absorption cross-section is small. Number of defects observed by ESR is up to several defects, and the number studied with electron microscopes is more than 100. Information obtained by neutron diffraction concerns the number of defects between these two ranges. For practical analysis, several probable models are selected from the data of ESR or electron microscopes, and most probable one is determined by calculation. Then, defect concentration is obtained from scattering cross section. It is possible to measure elastic scattering exclusively by neutron diffraction. Minimum detectable concentration estimated is about 0.5% and 10 20 - 10 21 defects per unit volume. A chopper and a time of flight system are used as a measuring system. Cold neutrons are obtained from the neutron sources inserted into reactors. Examples of measurements by using similar equipments to PTNS-I system of Japan Atomic Energy Research Institute are presented. Interstitial concentration in the graphite irradiated by fast neutrons is shown. Defects in irradiated MgO were also investigated by measuring scattering cross section. Study of defects in Ge was made by measuring total cross section, and model analysis was performed in comparison with various models. (Kato, T.)
Congenital heart defects in molecularly proven Kabuki syndrome patients.

Science.gov (United States)

Digilio, Maria Cristina; Gnazzo, Maria; Lepri, Francesca; Dentici, Maria Lisa; Pisaneschi, Elisa; Baban, Anwar; Passarelli, Chiara; Capolino, Rossella; Angioni, Adriano; Novelli, Antonio; Marino, Bruno; Dallapiccola, Bruno

2017-11-01

The prevalence of congenital heart defects (CHD) in Kabuki syndrome ranges from 28% to 80%. Between January 2012 and December 2015, 28 patients had a molecularly proven diagnosis of Kabuki syndrome. Pathogenic variants in KMT2D (MLL2) were detected in 27 patients, and in KDM6A gene in one. CHD was diagnosed in 19/27 (70%) patients with KMT2D (MLL2) variant, while the single patient with KDM6A change had a normal heart. The anatomic types among patients with CHD included aortic coarctation (4/19 = 21%) alone or associated with an additional CHD, bicuspid aortic valve (4/19 = 21%) alone or associated with an additional CHD, perimembranous subaortic ventricular septal defect (3/19 = 16%), atrial septal defect ostium secundum type (3/19 = 16%), conotruncal heart defects (3/19 = 16%). Additional CHDs diagnosed in single patients included aortic dilatation with mitral anomaly and hypoplastic left heart syndrome. We also reviewed CHDs in patients with a molecular diagnosis of Kabuki syndrome reported in the literature. In conclusion, a CHD is detected in 70% of patients with KMT2D (MLL2) pathogenic variants, most commonly left-sided obstructive lesions, including multiple left-sided obstructions similar to those observed in the spectrum of the Shone complex, and septal defects. Clinical management of Kabuki syndrome should include echocardiogram at the time of diagnosis, with particular attention to left-sided obstructive lesions and mitral anomalies, and annual monitoring for aortic arch dilatation. © 2017 Wiley Periodicals, Inc.
Relativistic and thermal effects on the magnon spectrum of a ferromagnetic monolayer.

Science.gov (United States)

Rózsa, L; Udvardi, L; Szunyogh, L

2013-12-18

A spin model including magnetic anisotropy terms and Dzyaloshinsky-Moriya interactions is studied for the case of a ferromagnetic monolayer with C2v symmetry like Fe/W(110). Using the quasiclassical stochastic Landau-Lifshitz-Gilbert equations, the magnon spectrum of the system is derived using linear response theory. The Dzyaloshinsky-Moriya interaction leads to asymmetry in the spectrum, while the anisotropy terms induce a gap. It is shown that, in the presence of lattice defects, both the Dzyaloshinsky-Moriya interactions and the two-site anisotropy lead to a softening of the magnon energies. Two methods are developed to investigate the magnon spectrum at finite temperatures. The theoretical results are compared to atomistic spin dynamics simulations and good agreement is found between them.

Quantum computing with defects.

Science.gov (United States)

Weber, J R; Koehl, W F; Varley, J B; Janotti, A; Buckley, B B; Van de Walle, C G; Awschalom, D D

2010-05-11

Identifying and designing physical systems for use as qubits, the basic units of quantum information, are critical steps in the development of a quantum computer. Among the possibilities in the solid state, a defect in diamond known as the nitrogen-vacancy (NV(-1)) center stands out for its robustness--its quantum state can be initialized, manipulated, and measured with high fidelity at room temperature. Here we describe how to systematically identify other deep center defects with similar quantum-mechanical properties. We present a list of physical criteria that these centers and their hosts should meet and explain how these requirements can be used in conjunction with electronic structure theory to intelligently sort through candidate defect systems. To illustrate these points in detail, we compare electronic structure calculations of the NV(-1) center in diamond with those of several deep centers in 4H silicon carbide (SiC). We then discuss the proposed criteria for similar defects in other tetrahedrally coordinated semiconductors.
Cracklike defects detection and sizing from co-occurrence matrices

International Nuclear Information System (INIS)

Moysan, J.; Benoist, P.; Magnin, I.

1991-01-01

The inspection of austenitic welds used in nuclear field with ultrasounds poses problems in interpretation: strong grain noise makes difficult the detection of the crack top and the crack bottom. Since corresponding echoes enable the defect sizing, defect sizing also becomes difficult. The formation of 2D images (BSCAN), and their processing enable an increase in the effectiveness of testing. We present a segmentation method, based on co-occurrence matrix, which separates defects zones and noise zones. Examples of segmentation improvement applied to artificial defects are presented
Phosphorous–vacancy–oxygen defects in silicon

KAUST Repository

Wang, Hao

2013-07-30

Electronic structure calculations employing the hybrid functional approach are used to gain fundamental insight in the interaction of phosphorous with oxygen interstitials and vacancies in silicon. It recently has been proposed, based on a binding energy analysis, that phosphorous–vacancy–oxygen defects may form. In the present study we investigate the stability of this defect as a function of the Fermi energy for the possible charge states. Spin polarization is found to be essential for the charge neutral defect.
Birth Defects

Science.gov (United States)

A birth defect is a problem that happens while a baby is developing in the mother's body. Most birth defects happen during the first 3 months of ... in the United States is born with a birth defect. A birth defect may affect how the ...
The Spectrum of Presentations of Cryptogenic Organizing Pneumonia in High Resolution Computed Tomography

International Nuclear Information System (INIS)

Mehrian, Payam; Shahnazi, Makhtoom; Dahaj, Ali Ahmadi; Bizhanzadeh, Sorour; Karimi, Mohammad Ali

2014-01-01

Various radiologic patterns of cryptogenic organizing pneumonia (COP) in X-rays have been reported for more than 20 years, and later, in computed tomography scans. The aim of the present study was to describe the spectrum of radiologic findings on high resolution computed tomography (HRCT) scans in patients with COP. HRCT scans of 31 sequential patients (mean age: 54.3±11 years; 55% male) with biopsy-proven COP in a tertiary lung center between 2009 and 2012 were reviewed by two experienced pulmonary radiologists with almost perfect interobserver agreement (kappa=0.83). Chest HRCTs from the lung apex to the base were performed using a 16-slice multi-detector CT scanner. The most common HRCT presentation of COP was ground-glass opacity (GGO) in 83.9% of cases, followed by consolidation in 71%. Both findings were mostly asymmetric bilateral and multifocal. Other common findings were the reverse halo (48.4%), parenchymal bands (54.8%) and subpleural bands (32.3%). Pulmonary nodules were found in about one-third of patients and were frequently smaller than 5 mm in diameter. Both GGOs and consolidations were revealed more often in the lower lobes. The main presentations of COP on HRCT include bilateral GGOs and consolidations in the lower lobes together with the reverse halo sign
Prenatal neurogenesis in autism spectrum disorders

Science.gov (United States)

Kaushik, Gaurav; Zarbalis, Konstantinos

2016-03-01

An ever-increasing body of literature describes compelling evidence that a subset of young children on the autism spectrum show abnormal cerebral growth trajectories. In these cases, normal cerebral size at birth is followed by a period of abnormal growth and starting in late childhood often by regression compared to unaffected controls. Recent work has demonstrated an abnormal increase in the number of neurons of the prefrontal cortex suggesting that cerebral size increase in autism is driven by excess neuronal production. In addition, some affected children display patches of abnormal laminar positioning of cortical projection neurons. As both cortical projection neuron numbers and their correct layering within the developing cortex requires the undisturbed proliferation of neural progenitors, it appears that neural progenitors lie in the center of the autism pathology associated with early brain overgrowth. Consequently, autism spectrum disorders associated with cerebral enlargement should be viewed as birth defects of an early embryonic origin with profound implications for their early diagnosis, preventive strategies, and therapeutic intervention.
Defects in semiconductors

International Nuclear Information System (INIS)

Pimentel, C.A.F.

1983-01-01

Some problems openned in the study of defects in semiconductors are presented. In particular, a review is made of the more important problems in Si monocrystals of basic and technological interest: microdefects and the presence of oxigen and carbon. The techniques usually utilized in the semiconductor material characterization are emphatized according its potentialities. Some applications of x-ray techniques in the epitaxial shell characterization in heterostructures, importants in electronic optics, are shown. The increase in the efficiency of these defect analysis methods in semiconductor materials with the use of synchrotron x-ray sources is shown. (L.C.) [pt
Defect characterization with positron annihilation

International Nuclear Information System (INIS)

Granatelli, L.; Lynn, K.G.

1980-01-01

Positron annihilation in metal crystals is reviewed. A brief introduction to the positron annihilation technique is presented first. Then the ability of the positron technique to perform microstructural characterization of four types of lattice defects (vacancies, voids, dislocations, grain boundaries) is discussed. It is frequently not possible to obtain samples that contain only one type of defect in nonnegligible concentrations. Such situations exist for some alloys and for fatigued metal samples. Finally, the current limitations and some future prospects of the technique are presented. 79 references, 14 figures, 1 table
The surface defect-related electroluminescence from the ZnO microwire

Energy Technology Data Exchange (ETDEWEB)

Ding Meng; Zhao Dongxu; Yao Bin; Li Binghui; Zhang Zhenzhong; Shan Chongxin; Shen Dezhen, E-mail: dxzhao2000@yahoo.com.cn [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130021 (China)

2011-02-23

Surface defect-related electroluminescence (EL) was realized from a single ZnO microwire-based metal-semiconductor-metal structure on a glass substrate. ZnO microwires were successfully fabricated using a simple chemical vapour deposition approach. Schottky contacts were detected between Au electrodes and the ZnO microwire. The EL spectrum showed a broad emission band covering the visible range from 400 to 700 nm. The possible EL emission mechanism is discussed in detail in this paper.
The electronic and optical properties of amorphous silica with hydrogen defects by ab initio calculations

Science.gov (United States)

Ren, Dahua; Xiang, Baoyan; Hu, Cheng; Qian, Kai; Cheng, Xinlu

2018-04-01

Hydrogen can be trapped in the bulk materials in four forms: interstitial molecular H2, interstitial atom H, O‑H+(2Si=O–H)+, Si‑H‑( {{4O}}\\bar \\equiv {{Si&x2212H}})‑ to affect the electronic and optical properties of amorphous silica. Therefore, the electronic and optical properties of defect-free and hydrogen defects in amorphous silica were performed within the scheme of density functional theory. Initially, the negative charged states hydrogen defects introduced new defect level between the valence band top and conduction band bottom. However, the neutral and positive charged state hydrogen defects made both the valence band and conduction band transfer to the lower energy. Subsequently, the optical properties such as absorption spectra, conductivity and loss functions were analyzed. It is indicated that the negative hydrogen defects caused the absorption peak ranging from 0 to 2.0 eV while the positive states produced absorption peaks at lower energy and two strong absorption peaks arose at 6.9 and 9.0 eV. However, the neutral hydrogen defects just improved the intensity of absorption spectrum. This may give insights into understanding the mechanism of laser-induced damage for optical materials. Project supported by the Science and Technology of Hubei Provincial Department of Education (No. B2017098).
Photometric estimation of defect size in radiation direction

International Nuclear Information System (INIS)

Zuev, V.M.

1993-01-01

Factors, affecting accuracy of photometric estimation of defect size in radiation transmission direction, are analyzed. Experimentally obtained dependences of contrast of defect image on its size in radiation transmission direction are presented. Practical recommendations on improving accuracy of photometric estimation of defect size in radiation transmission direction, are developed
Topological defects from the multiverse

Science.gov (United States)

Zhang, Jun; Blanco-Pillado, Jose J.; Garriga, Jaume; Vilenkin, Alexander

2015-05-01

Many theories of the early universe predict the existence of a multiverse where bubbles continuously nucleate giving rise to observers in their interior. In this paper, we point out that topological defects of several dimensionalities will also be produced in de Sitter like regions of the multiverse. In particular, defects could be spontaneously nucleated in our parent vacuum. We study the evolution of these defects as they collide with and propagate inside of our bubble. We estimate the present distribution of defects in the observable part of the universe. The expected number of such nearby defects turns out to be quite small, even for the highest nucleation rate. We also study collisions of strings and domain walls with our bubble in our past light cone. We obtain simulated full-sky maps of the loci of such collisions, and find their angular size distribution. Similarly to what happens in the case of bubble collisions, the prospect of detecting any collisions of our bubble with ambient defects is greatly enhanced in the case where the cosmological constant of our parent vacuum is much higher than the vacuum energy density during inflation in our bubble.
Topological defects from the multiverse

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jun [Institute of Cosmology, Department of Physics and Astronomy, Tufts University, Medford, MA 02155 (United States); Blanco-Pillado, Jose J. [Department of Theoretical Physics, University of the Basque Country UPV/EHU, 48080 Bilbao (Spain); IKERBASQUE, Basque Foundation for Science, 48013, Bilbao (Spain); Garriga, Jaume [Departament de Fisica Fonamental i Institut de Ciencies del Cosmos, Universitat de Barcelona, Marti i Franques, 1, 08028, Barcelona (Spain); Vilenkin, Alexander [Institute of Cosmology, Department of Physics and Astronomy, Tufts University, Medford, MA 02155 (United States)

2015-05-28

Many theories of the early universe predict the existence of a multiverse where bubbles continuously nucleate giving rise to observers in their interior. In this paper, we point out that topological defects of several dimensionalities will also be produced in de Sitter like regions of the multiverse. In particular, defects could be spontaneously nucleated in our parent vacuum. We study the evolution of these defects as they collide with and propagate inside of our bubble. We estimate the present distribution of defects in the observable part of the universe. The expected number of such nearby defects turns out to be quite small, even for the highest nucleation rate. We also study collisions of strings and domain walls with our bubble in our past light cone. We obtain simulated full-sky maps of the loci of such collisions, and find their angular size distribution. Similarly to what happens in the case of bubble collisions, the prospect of detecting any collisions of our bubble with ambient defects is greatly enhanced in the case where the cosmological constant of our parent vacuum is much higher than the vacuum energy density during inflation in our bubble.
Topological defects from the multiverse

International Nuclear Information System (INIS)

Zhang, Jun; Vilenkin, Alexander; Blanco-Pillado, Jose J.; Garriga, Jaume

2015-01-01

Many theories of the early universe predict the existence of a multiverse where bubbles continuously nucleate giving rise to observers in their interior. In this paper, we point out that topological defects of several dimensionalities will also be produced in de Sitter like regions of the multiverse. In particular, defects could be spontaneously nucleated in our parent vacuum. We study the evolution of these defects as they collide with and propagate inside of our bubble. We estimate the present distribution of defects in the observable part of the universe. The expected number of such nearby defects turns out to be quite small, even for the highest nucleation rate. We also study collisions of strings and domain walls with our bubble in our past light cone. We obtain simulated full-sky maps of the loci of such collisions, and find their angular size distribution. Similarly to what happens in the case of bubble collisions, the prospect of detecting any collisions of our bubble with ambient defects is greatly enhanced in the case where the cosmological constant of our parent vacuum is much higher than the vacuum energy density during inflation in our bubble
Secondary defects in non-metallic solids

International Nuclear Information System (INIS)

Ashbee, K.H.G.; Hobbs, L.W.

1977-01-01

This paper points out features of secondary defect formation which are peculiar to non-metallic solids (excluding elemental semiconductors). Most of the materials of interest are compounds of two or more (usually more or less ionic) atomic species, and immediate consequence of which is a need to maintain both stoichiometry (or accommodate non-stoichiometry) and order. Primary defects in these solids, whether produced thermally, chemically or by irradiation, seldom are present or aggregate in exactly stoichiometric proportions, and the resulting extending defect structures can be quite distinct from those found in metallic solids. Where stoichiometry is maintained, it is often convenient to describe extended defects in terms of alterations in the arrangement of 'molecular' units. The adoption of this procedure enables several novel features of extended defect structures in non-metals to be explained. There are several ways in which a range of non-stoichiometry can be accommodated, which include structural elimination of point defects, nucleation of new coherent phases of altered stoichiometry, and decomposition. (author)
Adult Autism Subthreshold Spectrum (AdAS Spectrum): Validation of a questionnaire investigating subthreshold autism spectrum.

Science.gov (United States)

Dell'Osso, L; Gesi, C; Massimetti, E; Cremone, I M; Barbuti, M; Maccariello, G; Moroni, I; Barlati, S; Castellini, G; Luciano, M; Bossini, L; Rocchetti, M; Signorelli, M; Aguglia, E; Fagiolini, A; Politi, P; Ricca, V; Vita, A; Carmassi, C; Maj, M

2017-02-01

Increasing literature has shown the usefulness of a dimensional approach to autism. The present study aimed to determine the psychometric properties of the Adult Autism Subthreshold Spectrum (AdAS Spectrum), a new questionnaire specifically tailored to assess subthreshold forms of autism spectrum disorder (ASD) in adulthood. 102 adults endorsing at least one DSM-5 symptom criterion for ASD (ASDc), 143 adults diagnosed with a feeding and eating disorder (FED), and 160 subjects with no mental disorders (CTL), were recruited from 7 Italian University Departments of Psychiatry and administered the following: SCID-5, Autism-Spectrum Quotient (AQ), Ritvo Autism and Asperger Diagnostic Scale 14-item version (RAADS-14), and AdAS Spectrum. The AdAS Spectrum demonstrated excellent internal consistency for the total score (Kuder-Richardson's coefficient=.964) as well as for five out of seven domains (all coefficients>.80) and sound test-retest reliability (ICC=.976). The total and domain AdAS Spectrum scores showed a moderate to strong (>.50) positive correlation with one another and with the AQ and RAADS-14 total scores. ASDc subjects reported significantly higher AdAS Spectrum total scores than both FED (pcriteria (FED 0 ) and those with one ASD symptom criterion (FED 1 ) , a gradient of severity in AdAS Spectrum scores from CTL subjects to ASD patients, across FED 0 , ASD 1 , FED 1 was shown. The AdAS Spectrum showed excellent internal consistency and test-retest reliability and strong convergent validity with alternative dimensional measures of ASD. The questionnaire performed differently among the three diagnostic groups and enlightened some significant effects of gender in the expression of autistic traits. Copyright © 2016 Elsevier Inc. All rights reserved.
Control of magnonic spectra in cobalt nanohole arrays: the effects of density, symmetry and defects

International Nuclear Information System (INIS)

Barman, Anjan

2010-01-01

Magnetic nanohole arrays are important systems for propagation of magnetic excitations and are among the potential candidates for magnonic crystals. A thorough investigation of magnonic band structures and the effect of the geometry of the array on them are important. Here, we present a systematic micromagnetic simulation study of magnonic modes in cobalt nanohole (antidot) arrays. In particular, we investigate the effects of the areal density and symmetry of the array and defects introduced in the array. The magnonic modes are strongly dependent on the density and the symmetry of the array but are weakly dependent on the defects. We have further investigated the modes in a tailored array consisting of equally wide hexagonal arrays with varying density. The magnonic spectrum of the tailored array contains additional modes above the modes of the constituent arrays due to the appearance of irregular domain structures at the regions joining arrays of two different types. This opens up the possibility of tuning the magnonic bands in magnetic nanohole arrays by careful design of the structure of the array.
Electron paramagnetic resonance of isolated Assub(Ga)+ antisite defect in neutron-transmutation doped semi-insulating GaAs

International Nuclear Information System (INIS)

Manasreh, M.O.; McDonald, P.F.; Kivlighn, S.A.; Minton, J.T.; Covington, B.C.

1988-01-01

The isolated Assub(Ga) antisite defect produced by the neutron-transmutation doping in semi-insulating GaAs was studied using the electron paramagnetic resonance technique. The results show that the optically induced quenching of the isolated Assub(Ga) + antisite defect is quite different from that of the EL2 center. Illumination with white light seems to always reduce the electron paramagnetic resonance spectrum suggesting that depopulation of the EL2 center does not introduce a noticeable change in the Assub(Ga) + antisite concentration. (author)
Robust frequency diversity based algorithm for clutter noise reduction of ultrasonic signals using multiple sub-spectrum phase coherence

Energy Technology Data Exchange (ETDEWEB)

Gongzhang, R.; Xiao, B.; Lardner, T.; Gachagan, A. [Centre for Ultrasonic Engineering, University of Strathclyde, Glasgow, G1 1XW (United Kingdom); Li, M. [School of Engineering, University of Glasgow, Glasgow, G12 8QQ (United Kingdom)

2014-02-18

This paper presents a robust frequency diversity based algorithm for clutter reduction in ultrasonic A-scan waveforms. The performance of conventional spectral-temporal techniques like Split Spectrum Processing (SSP) is highly dependent on the parameter selection, especially when the signal to noise ratio (SNR) is low. Although spatial beamforming offers noise reduction with less sensitivity to parameter variation, phased array techniques are not always available. The proposed algorithm first selects an ascending series of frequency bands. A signal is reconstructed for each selected band in which a defect is present when all frequency components are in uniform sign. Combining all reconstructed signals through averaging gives a probability profile of potential defect position. To facilitate data collection and validate the proposed algorithm, Full Matrix Capture is applied on the austenitic steel and high nickel alloy (HNA) samples with 5MHz transducer arrays. When processing A-scan signals with unrefined parameters, the proposed algorithm enhances SNR by 20dB for both samples and consequently, defects are more visible in B-scan images created from the large amount of A-scan traces. Importantly, the proposed algorithm is considered robust, while SSP is shown to fail on the austenitic steel data and achieves less SNR enhancement on the HNA data.
Electron transport in ethanol & methanol absorbed defected graphene

Science.gov (United States)

Dandeliya, Sushmita; Srivastava, Anurag

2018-05-01

In the present paper, the sensitivity of ethanol and methanol molecules on surface of single vacancy defected graphene has been investigated using density functional theory (DFT). The changes in structural and electronic properties before and after adsorption of ethanol and methanol were analyzed and the obtained results show high adsorption energy and charge transfer. High adsorption happens at the active site with monovacancy defect on graphene surface. Present work confirms that the defected graphene increases the surface reactivity towards ethanol and methanol molecules. The presence of molecules near the active site affects the electronic and transport properties of defected graphene which makes it a promising choice for designing methanol and ethanol sensor.

First-Principles Investigations of Defects in Minerals

Science.gov (United States)

Verma, Ashok K.

2011-07-01

The ideal crystal has an infinite 3-dimensional repetition of identical units which may be atoms or molecules. But real crystals are limited in size and they have disorder in stacking which as called defects. Basically three types of defects exist in solids: 1) point defects, 2) line defects, and 3) surface defects. Common point defects are vacant lattice sites, interstitial atoms and impurities and these are known to influence strongly many solid-state transport properties such as diffusion, electrical conduction, creep, etc. In thermal equilibrium point defects concentrations are determined by their formation enthalpies and their movement by their migration barriers. Line and surface defects are though absent from the ideal crystal in thermal equilibrium due to higher energy costs but they are invariably present in all real crystals. Line defects include edge-, screw- and mixed-dislocations and their presence is essential in explaining the mechanical strength and deformation of real crystals. Surface defects may arise at the boundary between two grains, or small crystals, within a larger crystal. A wide variety of grain boundaries can form in a polycrystal depending on factors such growth conditions and thermal treatment. In this talk we will present our first-principles density functional theory based defect studies of SiO2 polymorphs (stishovite, CaCl2-, α-PbO2-, and pyrite-type), Mg2SiO4 polymorphs (forsterite, wadsleyite and ringwoodite) and MgO [1-3]. Briefly, several native point defects including vacancies, interstitials, and their complexes were studied in silica polymorphs upto 200 GPa. Their values increase by a factor of 2 over the entire pressure range studied with large differences in some cases between different phases. The Schottky defects are energetically most favorable at zero pressure whereas O-Frenkel pairs become systematically more favorable at pressures higher than 20 GPa. The geometric and electronic structures of defects and migrating
Paramagnetic defects in hydrogenated amorphous carbon powders

International Nuclear Information System (INIS)

Keeble, D J; Robb, K M; Smith, G M; Mkami, H El; Rodil, S E; Robertson, J

2003-01-01

Hydrogenated amorphous carbon materials typically contain high concentrations of paramagnetic defects, the density of which can be quantified by electron paramagnetic resonance (EPR). In this work EPR measurements near 9.5, 94, and 189 GHz have been performed on polymeric and diamond-like hydrogenated amorphous carbon (a-C:H) powder samples. A similar single resonance line was observed at all frequencies for the two forms of a-C:H studied. No contributions to the spectrum from centres with resolved anisotropic g-values as reported earlier were detected. An increase in linewidth with microwave frequency was observed. Possible contributions to this frequency dependence are discussed
Effect of the defect-phosphorus atom complex interaction on the formation of the properties of neutron-doped silicon

International Nuclear Information System (INIS)

Kolesnik, L.I.; Lejferov, B.M.

1984-01-01

Radiation-induced defect annealing and changes in the concentration of substituting phosphorus atoms in silicon irradiated with different neutron doses have been studied by the low-temperature photoluminescence (PL) method at 4 K. Based on the PL spectrum character dependence on the fast-to-thermal neutron ration in a flux, series of lines and bands associated with the preferential formation of radiation-induced defects (within the 1.100 eV energy range) and with the presence of phosphorus impurity (1.15-1.12 eV) are identified. Some peculiarities are studied of the stage-by-stage annealing (250-500, 430-600, 600-800 deg C) of recombination-active centers (RAC) determining the radiation in the mentioned spectrum region. The relation between the RAC variations within the 1.12-1.15 eV range and the substituting phosphorus atom concentration in the 400-500 deg C temperature range is found. Activation energy of the substituting phosphorus atom concentration variation is estimated (approximately 0.5 eV). It is shown that the formation of defect-phosphorus complexes plays an important role in the formation of neutron-doped silicon properties, the presence of fast neutron in a flux being most importants
Germline cytotoxic lymphocytes defective mutations in Chinese patients with lymphoma.

Science.gov (United States)

Chen, Xue; Zhang, Yang; Wang, Fang; Wang, Mangju; Teng, Wen; Lin, Yuehui; Han, Xiangping; Jin, Fangyuan; Xu, Yuanli; Cao, Panxiang; Fang, Jiancheng; Zhu, Ping; Tong, Chunrong; Liu, Hongxing

2017-11-01

Certain patients with lymphoma may harbor mutations in perforin 1 (PRF1), unc-13 homolog D (UNC13D), syntaxin 11 (STX11), STXBP2 (syntaxin binding protein 2) or SH2 domain containing 1A (SH2D1A), which causes functional defects of cytotoxic lymphocytes. Data regarding the association between genetic defects and the development of lymphoma in Chinese patients are limited to date. In the present study, 90 patients with lymphoma were analyzed for UNC13D, PRF1, STXBP2, STX11, SH2D1A and X-linked inhibitor of apoptosis. Mutations were observed in 24 (26.67%) patients; 16 patients exhibited mutations in UNC13D, 7 exhibited PRF1 mutations, and 1 exhibited monoallelic mutation in STX11. UNC13D c.2588G>A/p.G863D mutation was detected in 9 patients (10.00%) and in 4/210 controls (1.90%). This mutation was predicted to be pathogenic and it predominantly existed in the Chinese population. These findings suggest that impaired cytotoxic machinery may represent a predisposing factor for the development of lymphoma. Furthermore, these data describe a distinct mutation spectrum in Chinese patients with lymphoma, whereby UNC13D is the most frequently mutated gene. In addition, these findings suggest UNC13D c.2588G>A mutation is a founder mutation in Chinese patients.
[Diagnostics of the genetic causes of autism spectrum disorders - a clinical geneticist's view].

Science.gov (United States)

Szczaluba, Krzysztof

2014-01-01

Explanation of the genetic basis of autism spectrum disorders has, for many decades, been a part of interest of researchers and clinicians. In recent years, thanks to modern molecular and cytogenetic techniques, a significant progress has been achieved in the diagnosis of genetic causes of autism. This applies particularly, but not exclusively, to those cases of autism that are accompanied by other clinical signs (i. e. complex phenotypes). The important clinical markers belong to different categories, and include congenital defects/anomalies, dysmorphism and macro-/microcephaly, to name the few. Thus, the choice of the diagnostic strategy depends on the clinical and pedigree information and, under Polish circumstances, the availability of specific diagnostic techniques and the amount of reimbursement under the National Health Service. Overall, the identification of the genetic causes of autism spectrum disorders is possible in about 10-30% of patients. In this paper the practical aspects of the use of different diagnostic techniques are briefly described. Some clinical examples and current recommendations for the diagnosis of patients with autism spectrum disorders are also presented. The point of view of a specialist in clinical genetics, increasingly involved, as part of the multidisciplinary care team, in the diagnostics of an autistic child has been demonstrated.
Thermophysical spectroscopy of defect states in silicon

International Nuclear Information System (INIS)

Igamberdyev, Kh.T.; Mamadalimov, A.T.; Khabibullaev, P.K.

1989-01-01

The present work deals with analyzing the possibilities of using the non-traditional thermophysical methods to study a defect structure in silicon. For this purpose, the temperature dependences of thermophysical properties of defect silicon are investigated. A number of new, earlier unknown physical phenomena in silicon are obtained, and their interpretation has enabled one to establish the main physical mechanisms of formation of deep defect states in silicon
Duplication of the pituitary gland associated with multiple blastogenesis defects: Duplication of the pituitary gland (DPG)-plus syndrome. Case report and review of literature.

Science.gov (United States)

Manjila, Sunil; Miller, Erin A; Vadera, Sumeet; Goel, Rishi K; Khan, Fahd R; Crowe, Carol; Geertman, Robert T

2012-01-01

Duplication of the pituitary gland (DPG) is a rare craniofacial developmental anomaly occurring during blastogenesis with postulated etiology such as incomplete twinning, teratogens, median cleft face syndrome or splitting of the notochord. The complex craniocaudal spectrum of blastogenesis defects associated with DPG is examined with an illustrative case. We report for the first time in the medical literature some unique associations with DPG, such as a clival encephalocele, third cerebral peduncle, duplicate odontoid process and a double tongue with independent volitional control. This patient also has the previously reported common associations such as duplicated sella, cleft palate, hypertelorism, callosal agenesis, hypothalamic enlargement, nasopharyngeal teratoma, fenestrated basilar artery and supernumerary teeth. This study also reviews 37 cases of DPG identified through MEDLINE literature search from 1880 to 2011. It provides a detailed analysis of the current case through physical examination and imaging. The authors propose that the developmental deformities associated with duplication of pituitary gland (DPG) occur as part of a developmental continuum, not as chance associations. Considering the fact that DPG is uniquely and certainly present throughout the spectrum of these blastogenesis defects, we suggest the term DPG-plus syndrome.
Influence of neutrophil defects on Burkholderia cepacia complex pathogenesis

Directory of Open Access Journals (Sweden)

Laura A. Porter

2011-11-01

Full Text Available The Burkholderia cepacia complex (Bcc is a group of Gram-negative bacteria that are ubiquitous in the environment and have emerged as opportunistic pathogens in immunocompromised patients. The primary patient populations infected with Bcc include individuals with cystic fibrosis (CF, as well as those with chronic granulomatous disease (CGD. While Bcc infection in CF is better characterized than in CGD, these two genetic diseases are not obviously similar and it is currently unknown if there is any commonality in host immune defects that is responsible for the susceptibility to Bcc. CF is caused by mutations in the CF transmembrane conductance regulator, resulting in manifestations in various organ systems, however the major cause of morbidity and mortality is currently due to bacterial respiratory infections. CGD, on the other hand, is a genetic disorder that is caused by defects in phagocyte NADPH oxidase. Because of the defect in CGD, phagocytes in these patients are unable to produce reactive oxygen species, which results in increased susceptibility to bacterial and fungal infections. Despite this significant defect in microbial clearance, the spectrum of pathogens frequently implicated in infections in CGD is relatively narrow and includes some bacterial species that are considered almost pathognomonic for this disorder. Very little is known about the cause of the specific susceptibility to Bcc over other potential pathogens more prevalent in the environment, and a better understanding of specific mechanisms required for bacterial virulence has become a high priority. This review will summarize both the current knowledge and future directions related to Bcc virulence in immunocompromised individuals with a focus on the roles of bacterial factors and neutrophil defects in pathogenesis.
Exploring atomic defects in molybdenum disulphide monolayers

KAUST Repository

Hong, Jinhua; Hu, Zhixin; Probert, Matt; Li, Kun; Lv, Danhui; Yang, Xinan; Gu, Lin; Mao, Nannan; Feng, Qingliang; Xie, Liming; Zhang, Jin; Wu, Dianzhong; Zhang, Zhiyong; Jin, Chuanhong; Ji, Wei; Zhang, Xixiang; Yuan, Jun; Zhang, Ze

2015-01-01

Defects usually play an important role in tailoring various properties of two-dimensional materials. Defects in two-dimensional monolayer molybdenum disulphide may be responsible for large variation of electric and optical properties. Here we present a comprehensive joint experiment-theory investigation of point defects in monolayer molybdenum disulphide prepared by mechanical exfoliation, physical and chemical vapour deposition. Defect species are systematically identified and their concentrations determined by aberration-corrected scanning transmission electron microscopy, and also studied by ab-initio calculation. Defect density up to 3.5 × 10 13 cm '2 is found and the dominant category of defects changes from sulphur vacancy in mechanical exfoliation and chemical vapour deposition samples to molybdenum antisite in physical vapour deposition samples. Influence of defects on electronic structure and charge-carrier mobility are predicted by calculation and observed by electric transport measurement. In light of these results, the growth of ultra-high-quality monolayer molybdenum disulphide appears a primary task for the community pursuing high-performance electronic devices.
Exploring atomic defects in molybdenum disulphide monolayers

KAUST Repository

Hong, Jinhua

2015-02-19

Defects usually play an important role in tailoring various properties of two-dimensional materials. Defects in two-dimensional monolayer molybdenum disulphide may be responsible for large variation of electric and optical properties. Here we present a comprehensive joint experiment-theory investigation of point defects in monolayer molybdenum disulphide prepared by mechanical exfoliation, physical and chemical vapour deposition. Defect species are systematically identified and their concentrations determined by aberration-corrected scanning transmission electron microscopy, and also studied by ab-initio calculation. Defect density up to 3.5 × 10 13 cm \\'2 is found and the dominant category of defects changes from sulphur vacancy in mechanical exfoliation and chemical vapour deposition samples to molybdenum antisite in physical vapour deposition samples. Influence of defects on electronic structure and charge-carrier mobility are predicted by calculation and observed by electric transport measurement. In light of these results, the growth of ultra-high-quality monolayer molybdenum disulphide appears a primary task for the community pursuing high-performance electronic devices.
Defect-impurity interactions in ion-implanted metals

International Nuclear Information System (INIS)

Turos, A.

1986-01-01

An overview of defect-impurity interactions in metals is presented. When point defects become mobile they migrate towards the sinks and on the way can be captured by impurity atoms forming stable associations so-called complexes. In some metallic systems complexes can also be formed athermally during ion implantation by trapping point defects already in the collision cascade. An association of a point defect with an impurity atom leads to its displacement from the lattice site. The structure and stability of complexes are strongly temperature dependent. With increasing temperature they dissociate or grow by multiple defect trapping. The appearance of freely migrating point defects at elevated temperatures, due to ion bombardment or thermal annealing, causes via coupling with defect fluxes, important impurity redistribution. Because of the sensitivity of many metal-in-metal implanted systems to radiation damage the understanding of this processes is essential for a proper interpretation of the lattice occupancy measurements and the optimization of implantation conditions. (author)
Ethanol exposure disrupts extraembryonic microtubule cytoskeleton and embryonic blastomere cell adhesion, producing epiboly and gastrulation defects

Directory of Open Access Journals (Sweden)

Swapnalee Sarmah

2013-08-01

Fetal alcohol spectrum disorder (FASD occurs when pregnant mothers consume alcohol, causing embryonic ethanol exposure and characteristic birth defects that include craniofacial, neural and cardiac defects. Gastrulation is a particularly sensitive developmental stage for teratogen exposure, and zebrafish is an outstanding model to study gastrulation and FASD. Epiboly (spreading blastomere cells over the yolk cell, prechordal plate migration and convergence/extension cell movements are sensitive to early ethanol exposure. Here, experiments are presented that characterize mechanisms of ethanol toxicity on epiboly and gastrulation. Epiboly mechanisms include blastomere radial intercalation cell movements and yolk cell microtubule cytoskeleton pulling the embryo to the vegetal pole. Both of these processes were disrupted by ethanol exposure. Ethanol effects on cell migration also indicated that cell adhesion was affected, which was confirmed by cell aggregation assays. E-cadherin cell adhesion molecule expression was not affected by ethanol exposure, but E-cadherin distribution, which controls epiboly and gastrulation, was changed. E-cadherin was redistributed into cytoplasmic aggregates in blastomeres and dramatically redistributed in the extraembryonic yolk cell. Gene expression microarray analysis was used to identify potential causative factors for early development defects, and expression of the cell adhesion molecule protocadherin-18a (pcdh18a, which controls epiboly, was significantly reduced in ethanol exposed embryos. Injecting pcdh18a synthetic mRNA in ethanol treated embryos partially rescued epiboly cell movements, including enveloping layer cell shape changes. Together, data show that epiboly and gastrulation defects induced by ethanol are multifactorial, and include yolk cell (extraembryonic tissue microtubule cytoskeleton disruption and blastomere adhesion defects, in part caused by reduced pcdh18a expression.
Altering graphene line defect properties using chemistry

Science.gov (United States)

Vasudevan, Smitha; White, Carter; Gunlycke, Daniel

2012-02-01

First-principles calculations are presented of a fundamental topological line defect in graphene that was observed and reported in Nature Nanotech. 5, 326 (2010). These calculations show that atoms and smaller molecules can bind covalently to the surface in the vicinity of the graphene line defect. It is also shown that the chemistry at the line defect has a strong effect on its electronic and magnetic properties, e.g. the ferromagnetically aligned moments along the line defect can be quenched by some adsorbates. The strong effect of the adsorbates on the line defect properties can be understood by examining how these adsorbates affect the boundary-localized states in the vicinity of the Fermi level. We also expect that the line defect chemistry will significantly affect the scattering properties of incident low-energy particles approaching it from graphene.
Micro-bridge defects: characterization and root cause analysis

Science.gov (United States)

Santoro, Gaetano; Van den Heuvel, Dieter; Braggin, Jennifer; Rosslee, Craig; Leray, Philippe J.; Cheng, Shaunee; Jehoul, Christiane; Schreutelkamp, Robert; Hillel, Noam

2010-03-01

Defect review of advanced lithography processes is becoming more and more challenging as feature sizes decrease. Previous studies using a defect review SEM on immersion lithography generated wafers have resulted in a defect classification scheme which, among others, includes a category for micro-bridges. Micro-bridges are small connections between two adjacent lines in photo-resist and are considered device killing defects. Micro-bridge rates also tend to increase as feature sizes decrease, making them even more important for the next technology nodes. Especially because micro-bridge defects can originate from different root causes, the need to further refine and split up the classification of this type of defect into sub groups may become a necessity. This paper focuses on finding the correlation of the different types of micro-bridge defects to a particular root cause based on a full characterization and root cause analysis of this class of defects, by using advanced SEM review capabilities like high quality imaging in very low FOV, Multi Perspective SEM Imaging (MPSI), tilted column and rotated stage (Tilt&Rotation) imaging and Focused Ion Beam (FIB) cross sectioning. Immersion lithography material has been mainly used to generate the set of data presented in this work even though, in the last part of the results, some EUV lithography data will be presented as part of the continuing effort to extend the micro-bridge defect characterization to the EUV technology on 40 nm technology node and beyond.
Tibial and fibular developmental fields defects

International Nuclear Information System (INIS)

Khoury, N.J.; Haddad, M.C.; Hourani, M.H.

1999-01-01

Malformations of the lower limbs are rare and heterogeneous anomalies. To explain the diversity and complexity of these abnormalities, authors introduced the concept of tibial and fibular developmental fields. Defects in these fields are responsible for different malformations, which have been described, to our knowledge, in only one report in the radiology literature. We present a case of a newborn with femoral bifurcation, absent fibulae and talar bones, ankle and foot malformations, and associated atrial septal defect. Our case is an example of defects in both fibular and tibial developmental fields. (orig.)
Carrier removal and defect behavior in p-type InP

Science.gov (United States)

Weinberg, I.; Swartz, C. K.; Drevinsky, P. J.

1992-01-01

A simple expression, obtained from the rate equation for defect production, was used to relate carrier removal to defect production and hole trapping rates in p-type InP after irradiation by 1-MeV electrons. Specific contributions to carrier removal from defect levels H3, H4, and H5 were determined from combined deep-level transient spectroscopy (DLTS) and measured carrier concentrations. An additional contribution was attributed to one or more defects not observed by the present DLTS measurements. The high trapping rate observed for H5 suggests that this defect, if present in relatively high concentration, could be dominant in p-type InP.
Lattice vibrations and thermal properties of carbon nitride with defect ZnS structure from first-principles calculations

NARCIS (Netherlands)

Fang, C.M.; Wijs, G.A. de

2004-01-01

The phonon spectrum Of C3N4 with defect zincblende-type structure (deltaC(3)N(4)) was calculated by density functional theory (DFT) techniques. The results permit an assessment of important mechanical and thermodynamical properties such as the bulk modulus, lattice specific heat, vibration energy,
Theory of Defects in Semiconductors

CERN Document Server

Drabold, David A

2007-01-01

Semiconductor science and technology is the art of defect engineering. The theoretical modeling of defects has improved dramatically over the past decade. These tools are now applied to a wide range of materials issues: quantum dots, buckyballs, spintronics, interfaces, amorphous systems, and many others. This volume presents a coherent and detailed description of the field, and brings together leaders in theoretical research. Today's state-of-the-art, as well as tomorrow’s tools, are discussed: the supercell-pseudopotential method, the GW formalism,Quantum Monte Carlo, learn-on-the-fly molecular dynamics, finite-temperature treatments, etc. A wealth of applications are included, from point defects to wafer bonding or the propagation of dislocation.
Paediatric post-traumatic cortical defects of the distal radius

International Nuclear Information System (INIS)

Roach, Richard T.; Summers, Bruce N.; Cassar-Pullicino, Victor

2002-01-01

Paediatric post-traumatic cortical defects, although rare, are predominately seen affecting the distal radius following a greenstick or torus fracture. We review the literature and present a further two cases supported by CT and MRI. Images from an acute greenstick fracture are also presented to help understand the pathogenesis. Defects are typically solitary on plain radiographs and are usually noticed late, proximal to the site of compression. They are non-expansile in an otherwise healthy child. CT and MRI may reveal smaller multiple subperiosteal defects. Typical defects require no further management other than reassurance and advice that they may occasionally cause discomfort but resolve with time. (orig.)
Varying stiffness and load distributions in defective ball bearings: Analytical formulation and application to defect size estimation

Science.gov (United States)

Petersen, Dick; Howard, Carl; Prime, Zebb

2015-02-01

This paper presents an analytical formulation of the load distribution and varying effective stiffness of a ball bearing assembly with a raceway defect of varying size, subjected to static loading in the radial, axial and rotational degrees of freedom. The analytical formulation is used to study the effect of the size of the defect on the load distribution and varying stiffness of the bearing assembly. The study considers a square-shaped outer raceway defect centered in the load zone and the bearing is loaded in the radial and axial directions while the moment loads are zero. Analysis of the load distributions shows that as the defect size increases, defect-free raceway sections are subjected to increased static loading when one or more balls completely or partly destress when positioned in the defect zone. The stiffness variations that occur when balls pass through the defect zone are significantly larger and change more rapidly at the defect entrance and exit than the stiffness variations that occur for the defect-free bearing case. These larger, more rapid stiffness variations generate parametric excitations which produce the low frequency defect entrance and exit events typically observed in the vibration response of a bearing with a square-shaped raceway defect. Analysis of the stiffness variations further shows that as the defect size increases, the mean radial stiffness decreases in the loaded radial and axial directions and increases in the unloaded radial direction. The effects of such stiffness changes on the low frequency entrance and exit events in the vibration response are simulated with a multi-body nonlinear dynamic model. Previous work used the time difference between the low frequency entrance event and the high frequency exit event to estimate the size of the defect. However, these previous defect size estimation techniques cannot distinguish between defects that differ in size by an integer number of the ball angular spacing, and a third feature

Nanocarbon: Defect Architectures and Properties

Science.gov (United States)

Vuong, Amanda

The allotropes of carbon make its solid phases amongst the most diverse of any element. It can occur naturally as graphite and diamond, which have very different properties that make them suitable for a wide range of technological and commercial purposes. Recent developments in synthetic carbon include Highly Oriented Pyrolytic Graphite (HOPG) and nano-carbons, such as fullerenes, nanotubes and graphene. The main industrial application of bulk graphite is as an electrode material in steel production, but in purified nuclear graphite form, it is also used as a moderator in Advanced Gas-cooled Reactors across the United Kingdom. Both graphene and graphite are damaged over time when subjected to bombardment by electrons, neutrons or ions, and these have a wide range of effects on their physical and electrical properties, depending on the radiation flux and temperature. This research focuses on intrinsic defects in graphene and dimensional change in nuclear graphite. The method used here is computational chemistry, which complements physical experiments. Techniques used comprise of density functional theory (DFT) and molecular dynamics (MD), which are discussed in chapter 2 and chapter 3, respectively. The succeeding chapters describe the results of simulations performed to model defects in graphene and graphite. Chapter 4 presents the results of ab initio DFT calculations performed to investigate vacancy complexes that are formed in AA stacked bilayer graphene. In AB stacking, carbon atoms surrounding the lattice vacancies can form interlayer structures with sp2 bonding that are lower in energy compared to in-plane reconstructions. From the investigation of AA stacking, sp2 interlayer bonding of adjacent multivacancy defects in registry creates a type of stable sp2 bonded wormhole between the layers. Also, a new class of mezzanine structure characterised by sp3 interlayer bonding, resembling a prismatic vacancy loop has also been identified. The mezzanine, which is a
Paranoid personality disorder and the schizophrenia spectrum-Where to draw the line?

Science.gov (United States)

Birkeland, Søren Fryd

2013-08-01

By means of a case vignette, this study explores the clinical intersection between paranoid personality disorder and other schizophrenia-spectrum illness. Even though the patient described had paramount signs of a paranoid personality disorder and was diagnosed as such, psychopathological symptoms extended considerably beyond the common concept and diagnostic criteria of the disorder. Management strategies included psychopharmacological and non-pharmacological interventions, yet psychosocial functioning permanently appeared defective. While there is a persistent need for an opportunity to distinguish the characteristic syndromal pattern of paranoid personality attributes, the case exemplifies the challenges associated with classifying some largely suspicious and distrustful eccentrics within the schizophrenia spectrum. Copyright © 2013 John Wiley & Sons, Ltd.
Oxygen defect processes in silicon and silicon germanium

KAUST Repository

Chroneos, A.

2015-06-18

Silicon and silicon germanium are the archetypical elemental and alloy semiconductor materials for nanoelectronic, sensor, and photovoltaic applications. The investigation of radiation induced defects involving oxygen, carbon, and intrinsic defects is important for the improvement of devices as these defects can have a deleterious impact on the properties of silicon and silicon germanium. In the present review, we mainly focus on oxygen-related defects and the impact of isovalent doping on their properties in silicon and silicon germanium. The efficacy of the isovalent doping strategies to constrain the oxygen-related defects is discussed in view of recent infrared spectroscopy and density functional theory studies.
Oxygen defect processes in silicon and silicon germanium

KAUST Repository

Chroneos, A.; Sgourou, E. N.; Londos, C. A.; Schwingenschlö gl, Udo

2015-01-01

Silicon and silicon germanium are the archetypical elemental and alloy semiconductor materials for nanoelectronic, sensor, and photovoltaic applications. The investigation of radiation induced defects involving oxygen, carbon, and intrinsic defects is important for the improvement of devices as these defects can have a deleterious impact on the properties of silicon and silicon germanium. In the present review, we mainly focus on oxygen-related defects and the impact of isovalent doping on their properties in silicon and silicon germanium. The efficacy of the isovalent doping strategies to constrain the oxygen-related defects is discussed in view of recent infrared spectroscopy and density functional theory studies.
Defect pin behaviour in the DFR

International Nuclear Information System (INIS)

Sloss, W.M.; Bagley, K.Q.; Edmonds, E.; Potter, P.E.

1979-01-01

A program of defective fuel pin irradiations has been carried out in the DFR. This program employed fuel pins which had failed during previous irradiations (natural defects) and pins in which simulated failures (artificial defects) had been induced prior to irradiation or during an intermediate examination stage at moderate or substantial burnups. The artificial defects simulated longitudinal ruptures and were normally located at positions near the top, middle and bottom of the pin where clad temperatures were 450, 540 and 630 0 C respectively. The fuel was mixed U-Pu oxide, and fuel form, stoichiometry, clad type, pin diameter, linear rating, and burnup were among the variables examined. The defect pin tests were normally carried out in single pin or trefoil type vehicles. After irradiation all the pins were subjected to the normal nondestructive examination procedures and the visual, radiographic, gamma-scanning, and dimensional change results are presented. Several pins were destructively examined and the metallographic data are discussed
Defect kinetics in novel detector materials

CERN Document Server

MacEvoy, B C

2000-01-01

Silicon particle detectors will be used extensively in experiments at the CERN Large Hadron Collider, where unprecedented particle fluences will cause significant atomic displacement damage. We present a model of the evolution of defect concentrations and consequent electrical behaviour in "novel" detector materials with various oxygen and carbon impurity concentrations. The divacancy-oxygen (V/sub 2/O) defect is identified as the cause of changes in device characteristics during /sup 60/Co gamma irradiation. In the case of hadron irradiation changes in detector doping concentration (N/sub eff/) are dominated by cluster defects, in particular the divacancy (V/sub 2/), which exchange charge directly via a non-Shockley-Read- Hall mechanism. The V/sub 2/O defect also contributes to Ne/sub eff/. This defect is more copiously produced during 24 GeV/c proton irradiation than during 1 MeV neutron irradiation on account of the higher vacancy introduction rate, hence the radiation hardness of materials is more sensiti...
Immobile defects in ferroelastic walls: Wall nucleation at defect sites

Science.gov (United States)

He, X.; Salje, E. K. H.; Ding, X.; Sun, J.

2018-02-01

Randomly distributed, static defects are enriched in ferroelastic domain walls. The relative concentration of defects in walls, Nd, follows a power law distribution as a function of the total defect concentration C: N d ˜ C α with α = 0.4 . The enrichment Nd/C ranges from ˜50 times when C = 10 ppm to ˜3 times when C = 1000 ppm. The resulting enrichment is due to nucleation at defect sites as observed in large scale MD simulations. The dynamics of domain nucleation and switching is dependent on the defect concentration. Their energy distribution follows the power law with exponents during yield between ɛ ˜ 1.82 and 2.0 when the defect concentration increases. The power law exponent is ɛ ≈ 2.7 in the plastic regime, independent of the defect concentration.
Investigation of anisotropy in EPR spectra of radiation defects in irradiated beryllium ceramics

International Nuclear Information System (INIS)

Polyakov, A.I.; Ryabikin, Yu.A.; Zashkvara, O. V.; Bitenbaev, M.I.; Petukhov, Yu. V.

2004-01-01

Full text: In this work results of analysis of anisotropy and hyperfine structure in EPR spectra of paramagnetic defects in irradiated samples of beryllium ceramics are presented. To explain peculiarities in a shape and parameters of the EPR spectrum hyperfine structure in beryllium ceramics, we have analyzed several versions of model representations for the radiation-induced paramagnetic defects uniformly distributed in a sample as well as for cluster defects which hyperfine structure is determined by interactions between electrons and nuclei of impurity atoms (S=1/2) and which are characterized by anisotropy in the g factors. Calculations of a shape of the uniformly widened EPR spectra are carried out by the model of random interactions between electron spins. The EPR spectra, widened at the expense of anisotropy in the g factors, are calculated by the following equation: g(Δ)=[2(ω-ω 0 )+α] -1/2 , where ω 0 =γH 0 , α is the quantify proportional to the anisotropy shift. To describe wings of spectral lines, where the equation doesn't work, we use the Gaussian function. To determine the frequency of precession of electron spins packages with local concentration N loc , the following expression is used: ω=ω 0 +1/2α(3cos 2 θ-1), where θ is an angle between the symmetry axis and the direction of the external magnetic field. It is shown that the best agreement between the calculated and experimental EPR spectra is observed with the following computational model: paramagnetic radiation defects are distributed uniformly over a ceramics sample, and the g factors of its EPR spectra have the anisotropy typical for dipole-dipole interaction in powder samples. By results of the data we obtained, it's clear that in future we'll need in more detailed information than that published in scientific journals about formation of the paramagnetic defect EPR spectra structure in beryllium oxides and ceramics at the expense of resonance line hyperfine splitting on atoms of
Investigation of anisotropy in EPR spectra of radiation defects in irradiated beryllium ceramics

Energy Technology Data Exchange (ETDEWEB)

Polyakov, A I; Ryabikin, Yu A; Zashkvara, O V; Bitenbaev, M I; Petukhov, Yu V [Inst. of Physics and Technology, Almaty (Kazakhstan)

2004-07-01

Full text: In this work results of analysis of anisotropy and hyperfine structure in EPR spectra of paramagnetic defects in irradiated samples of beryllium ceramics are presented. To explain peculiarities in a shape and parameters of the EPR spectrum hyperfine structure in beryllium ceramics, we have analyzed several versions of model representations for the radiation-induced paramagnetic defects uniformly distributed in a sample as well as for cluster defects which hyperfine structure is determined by interactions between electrons and nuclei of impurity atoms (S=1/2) and which are characterized by anisotropy in the g factors. Calculations of a shape of the uniformly widened EPR spectra are carried out by the model of random interactions between electron spins. The EPR spectra, widened at the expense of anisotropy in the g factors, are calculated by the following equation: g({delta})=[2({omega}-{omega}{sub 0})+{alpha}]{sup -1/2}, where {omega}{sub 0}={gamma}H{sub 0}, {alpha} is the quantify proportional to the anisotropy shift. To describe wings of spectral lines, where the equation doesn't work, we use the Gaussian function. To determine the frequency of precession of electron spins packages with local concentration N{sub loc}, the following expression is used: {omega}={omega}{sub 0}+1/2{alpha}(3cos{sup 2}{theta}-1), where {theta} is an angle between the symmetry axis and the direction of the external magnetic field. It is shown that the best agreement between the calculated and experimental EPR spectra is observed with the following computational model: paramagnetic radiation defects are distributed uniformly over a ceramics sample, and the g factors of its EPR spectra have the anisotropy typical for dipole-dipole interaction in powder samples. By results of the data we obtained, it's clear that in future we'll need in more detailed information than that published in scientific journals about formation of the paramagnetic defect EPR spectra structure in
Defect identification for the AsGa family

International Nuclear Information System (INIS)

Overhof, H.; Spaeth, J.-M.

2003-01-01

The As Ga family consists of at least four distinctly different point defects including the technologically important EL2 defect. While the different members are easily distinguished from their MCDA spectra, the differences of the hf and shf interactions as derived from ODEPR and ODENDOR are rather small. We present ab initio calculations using the LMTO-ASA Green's function method for a variety of defect models that might be relevant for the identification of As Ga -related defects. We confirm the identification of the isolated As Ga and show that the {As Ga -X 2 } defect must be identified with the nearest-neighbor antistructure pair rather than with the {As Ga -V As } pair. For the {As Ga -X 1 } defect a distant antistructure pair is a likely candidate. For the EL2, the most important member of the As Ga family, we have not found a conclusive defect model. The recent ODENDOR data are similar to those of the distant orthorhombic {As Ga -V Ga } pair, which, however is a triple acceptor and not a donor
Optical transmission properties of an anisotropic defect cavity in one-dimensional photonic crystal

Science.gov (United States)

Ouchani, Noama; El Moussaouy, Abdelaziz; Aynaou, Hassan; El Hassouani, Youssef; El Boudouti, El Houssaine; Djafari-Rouhani, Bahram

2018-01-01

We investigate theoretically the possibility to control the optical transmission in the visible and infrared regions by a defective one dimensional photonic crystal formed by a combination of a finite isotropic superlattice and an anisotropic defect layer. The Green's function approach has been used to derive the reflection and the transmission coefficients, as well as the densities of states of the optical modes. We evaluate the delay times of the localized modes and we compare their behavior with the total densities of states. We show that the birefringence of an anisotropic defect layer has a significant impact on the behavior of the optical modes in the electromagnetic forbidden bands of the structure. The amplitudes of the defect modes in the transmission and the delay time spectrum, depend strongly on the position of the cavity layer within the photonic crystal. The anisotropic defect layer induces transmission zeros in one of the two components of the transmission as a consequence of a destructive interference of the two polarized waves within this layer, giving rise to negative delay times for some wavelengths in the visible and infrared light ranges. This property is a typical characteristic of the anisotropic photonic layer and is without analogue in their counterpart isotropic defect layers. This structure offers several possibilities for controlling the frequencies, transmitted intensities and the delay times of the optical modes in the visible and infrared regions. It can be a good candidate for realizing high-precision optical filters.
Phononic crystals with one-dimensional defect as sensor materials

Science.gov (United States)

Aly, Arafa H.; Mehaney, Ahmed

2017-09-01

Recently, sensor technology has attracted great attention in many fields due to its importance in many engineering applications. In the present work, we introduce a study using the innovative properties of phononic crystals in enhancing a new type of sensors based on the intensity of transmitted frequencies inside the phononic band gaps. Based on the transfer matrix method and Bloch theory, the expressions of the reflection coefficient and dispersion relation are presented. Firstly, the influences of filling fraction ratio and the angle of incidence on the band gap width are discussed. Secondly, the localization of waves inside band gaps is discussed by enhancing the properties of the defected phononic crystal. Compared to the periodic structure, localization modes involved within the band structure of phononic crystals with one and two defect layers are presented and compared. Trapped localized modes can be detected easily and provide more information about defected structures. Such method could increase the knowledge of manufacturing defects by measuring the intensity of propagated waves in the resonant cavities and waveguides. Moreover, several factors enhance the role of the defect layer on the transmission properties of defected phononic crystals are presented. The acoustic band gap can be used to detect or sense the type of liquids filling the defect layer. The liquids make specific resonant modes through the phononic band gaps that related to the properties of each liquid. The frequency where the maximum resonant modes occur is correlated to material properties and allows to determine several parameters such as the type of an unknown material.
Interaction of corrosion defects in pipelines – Part 1: Fundamentals

International Nuclear Information System (INIS)

Benjamin, Adilson C.; Freire, José Luiz F.; Vieira, Ronaldo D.; Cunha, Divino J.S.

2016-01-01

Corrosion defects, also called metal loss due to corrosion, are frequently found in carbon steel pipelines. Corrosion defects may occur singly or in colonies. Usually the failure pressure of a colony of closely spaced corrosion defects is smaller than the failure pressures that the defects would attain if they were isolated. This reduction in the corroded pipe pressure strength is due to the interaction between adjacent defects. The interaction of corrosion defects in pipelines is the subject of two companion papers. In the present paper (the Part 1 paper) a literature review and the fundamentals of interaction of corrosion defects in pipelines are presented. In the subsequent paper (the Part 2 paper) initially the database of corroded pipe tests generated during the MTI JIP is described. Then the failure pressures contained in the MTI JIP database of corroded pipe tests are compared with those predicted by six of the currently available assessment methods. MTI JIP is the acronym for Mixed Type Interaction Joint Industry Project.
Line broadening mechanisms of the orth-H2 pair spectrum

International Nuclear Information System (INIS)

Statt, B.W.; Hardy, W.N.

1980-01-01

Three broadening mechanisms for the ortho pair spectrum in solid hydrogen are investigated. First, theoretical predictions of the phonon induced lifetime broadening are presented. Next a theory is developed which gives the inhomogeneous broadening due to the presence of ortho molecules surrounding the pairs. An unexpected result is that certain lines remain unbroadened, at least to within the approximation made. Strain effects due to isotopic mass defect impurities are also considered. These predictions are then compared with experimental results. No temperature dependence of the lineshapes is observed, setting an upper limit on the phonon broadening contribution to the linewidth. This limit is an order of magnitude lower than the theory predicts. The predictions of the ortho broadening theory, on the other hand, are in good agreement with experiment. Samples doped with isotopic impurities are also investigated. (auth)
Modeling of extended defects in silicon

International Nuclear Information System (INIS)

Law, M.E.; Jones, K.S.; Earles, S.K.; Lilak, A.D.; Xu, J.W.

1997-01-01

Transient Enhanced Diffusion (TED) is one of the biggest modeling challenges present in predicting scaled technologies. Damage from implantation of dopant ions changes the diffusivities of the dopants and precipitates to form complex extended defects. Developing a quantitative model for the extended defect behavior during short time, low temperature anneals is a key to explaining TED. This paper reviews some of the modeling developments over the last several years, and discusses some of the challenges that remain to be addressed. Two examples of models compared to experimental work are presented and discussed
A novel inspection system for cosmetic defects

Science.gov (United States)

Hazra, S.; Roy, R.; Williams, D.; Aylmore, R.; Hollingdale, D.

2013-12-01

The appearance of automotive skin panels creates desirability for a product and differentiates it from the competition. Because of the importance of skin panels, considerable care is taken in minimizing defects such as the 'hollow' defect that occur around door-handle depressions. However, the inspection process is manual, subjective and time-consuming. This paper describes the development of an objective and inspection scheme for the 'hollow' defect. In this inspection process, the geometry of a panel is captured using a structured lighting system. The geometry data is subsequently analyzed by a purpose-built wavelet-based algorithm to identify the location of any defects that may be present and to estimate the perceived severity of the defects without user intervention. This paper describes and critically evaluates the behavior of this physically-based algorithm on an ideal and real geometry and compares its result to an actual audit. The results show that the algorithm is capable of objectively locating and classifying 'hollow' defects in actual panels.
Immunologic effects of whole body ultraviolet (uv) irradiation. II. Defect in splenic adherent cell antigen presentation for stimulation of T cell proliferation

International Nuclear Information System (INIS)

Letvin, N.L.; Fox, I.J.; Greene, M.I.; Benacerraf, B.; Germain, R.N.

1980-01-01

Ultraviolet (uv) irradiation has been shown to alter many parameters of the immunologic reactivity of mice. The altered responsiveness of uv-irradiated mice, as measured by delayed-type hypersensitivity (DTH) and primary in vitro plaque-forming cell (PFC) responses to T-dependent antigens, has recently been correlated with a functional defect in the splenic adherent cell population of these animals. The present studies describe a model of this altered responsiveness, which allows further clarification of the effects of external uv irradiation on the splenic antigen-presenting cell (APC) in its interactions with T cells
Large-Scale Molecular Simulations on the Mechanical Response and Failure Behavior of a defective Graphene: Cases of 5-8-5 Defects

Science.gov (United States)

Wang, Shuaiwei; Yang, Baocheng; Yuan, Jinyun; Si, Yubing; Chen, Houyang

2015-10-01

Understanding the effect of defects on mechanical responses and failure behaviors of a graphene membrane is important for its applications. As examples, in this paper, a family of graphene with various 5-8-5 defects are designed and their mechanical responses are investigated by employing molecular dynamics simulations. The dependence of fracture strength and strain as well as Young’s moduli on the nearest neighbor distance and defect types is examined. By introducing the 5-8-5 defects into graphene, the fracture strength and strain become smaller. However, the Young’s moduli of DL (Linear arrangement of repeat unit 5-8-5 defect along zigzag-direction of graphene), DS (a Slope angle between repeat unit 5-8-5 defect and zigzag direction of graphene) and DZ (Zigzag-like 5-8-5 defects) defects in the zigzag direction become larger than those in the pristine graphene in the same direction. A maximum increase of 11.8% of Young’s modulus is obtained. Furthermore, the brittle cracking mechanism is proposed for the graphene with 5-8-5 defects. The present work may provide insights in controlling the mechanical properties by preparing defects in the graphene, and give a full picture for the applications of graphene with defects in flexible electronics and nanodevices.
Studies of defects and defect agglomerates by positron annihilation spectroscopy

DEFF Research Database (Denmark)

Eldrup, Morten Mostgaard; Singh, B.N.

1997-01-01

A brief introduction to positron annihilation spectroscopy (PAS), and in particular lo its use for defect studies in metals is given. Positrons injected into a metal may become trapped in defects such as vacancies, vacancy clusters, voids, bubbles and dislocations and subsequently annihilate from...... the trapped state iri the defect. The annihilation characteristics (e.g., the lifetime of the positron) can be measured and provide information about the nature of the defect (e.g., size, density, morphology). The technique is sensitive to both defect size (in the range from monovacancies up to cavities...
Soft Tissue Reconstruction of Complete Circumferential Defects of the Upper Extremity

Directory of Open Access Journals (Sweden)

Zhi Yang Ng

2017-03-01

Full Text Available BackgroundUpper extremity soft tissue defects with complete circumferential involvement are not common. Coupled with the unique anatomy of the upper extremity, the underlying etiology of such circumferential soft tissue defects represent additional reconstructive challenges that require treatment to be tailored to both the patient and the wound. The aim of this study is to review the various options for soft tissue reconstruction of complete circumferential defects in the upper extremity.MethodsA literature review of PubMed and MEDLINE up to December 2016 was performed. The current study focuses on forearm and arm defects from the level at or proximal to the wrist and were assessed based on Tajima's classification (J Trauma 1974. Data reviewed for analysis included patient demographics, causality, defect size, reconstructive technique(s employed, and postoperative follow-up and functional outcomes (when available.ResultsIn accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines, 14 unique articles were identified for a total of 50 patients (mean=28.1 years. Underlying etiologies varied from extensive thermal or electrical burns to high impact trauma leading to degloving or avulsion, crush injuries, or even occur iatrogenically after tumor extirpation or extensive debridement. Treatment options ranged from the application of negative pressure wound dressings to the opposite end of the spectrum in hand transplantation.ConclusionsWith the evolution of reconstructive techniques over time, the extent of functional and aesthetic rehabilitation of these complex upper extremity injuries has also improved. The proposed management algorithm comprehensively addresses the inherent challenges associated with these complex cases.

Defect modelling

International Nuclear Information System (INIS)

Norgett, M.J.

1980-01-01

Calculations, drawing principally on developments at AERE Harwell, of the relaxation about lattice defects are reviewed with emphasis on the techniques required for such calculations. The principles of defect modelling are outlined and various programs developed for defect simulations are discussed. Particular calculations for metals, ionic crystals and oxides, are considered. (UK)
Surface defect assisted broad spectra emission from CdSe quantum dots for white LED application

Science.gov (United States)

Samuel, Boni; Mathew, S.; Anand, V. R.; Correya, Adrine Antony; Nampoori, V. P. N.; Mujeeb, A.

2018-02-01

This paper reports, broadband photoluminescence from CdSe quantum dots (QDs) under the excitation of 403 nm using fluorimeter and 403 nm CW laser excitation. The broad spectrum obtained from the colloidal quantum dots was ranges from 450 nm to 800 nm. The broadness of the spectra was attributed to the merging of band edge and defect driven emissions from the QDs. Six different sizes of particles were prepared via kinetic growth method by using CdO and elemental Se as sources of Cd and Se respectively. The particle sizes were measured from TEM images. The size dependent effect on broad emission was also studied and the defect state emission was found to be predominant in very small QDs. The defect driven emission was also observed to be redshifted, similar to the band edge emission, due to quantum confinement effect. The emission corresponding to different laser power was also studied and a linear relation was obtained. In order to study the colour characteristics of the emission, CIE chromaticity coordinate, CRI and CCT of the prepared samples were measured. It is observed that, these values were tunable by the addition of suitable intensity of blue light from the excitation source to yield white light of various colour temperatures. The broad photoluminescence spectrum of the QDs, were compared with that of a commercially available white LED. It was found that the prepared QDs are good alternatives for the phosphor in phosphor converted white LEDs, to provide good spectral tunability.
Key Questions in Building Defect Prediction Models in Practice

Science.gov (United States)

Ramler, Rudolf; Wolfmaier, Klaus; Stauder, Erwin; Kossak, Felix; Natschläger, Thomas

The information about which modules of a future version of a software system are defect-prone is a valuable planning aid for quality managers and testers. Defect prediction promises to indicate these defect-prone modules. However, constructing effective defect prediction models in an industrial setting involves a number of key questions. In this paper we discuss ten key questions identified in context of establishing defect prediction in a large software development project. Seven consecutive versions of the software system have been used to construct and validate defect prediction models for system test planning. Furthermore, the paper presents initial empirical results from the studied project and, by this means, contributes answers to the identified questions.
Tracking architectural defects in university building in Malaysia

Directory of Open Access Journals (Sweden)

Mohd Isa Haryati

2016-01-01

Full Text Available Building defects are always the key concern in the construction industry. Defects represent not only a loss to the project but also hamper the smooth operation of a building. Recognising the need to resolve these continuing problems, a research was mooted to track from the study of defects that occurred during the Defects Liability Period in a public university in Malaysia. This paper presents part of the research which investigates what can be learnt from the analysis of architectural defects in these projects. Two research objectives were developed (1 to investigate types of architectural defects that occurred and (2 to analyse the causes of the defects. A mixed methods approach is adopted. Data for the quantitative element of the research was drawn from defects audit records of the project. They were sorted, grouped and transferred into the SPSS software for analysis using the measure of central tendencies and frequency analysis. The findings suggest that with a proper methodology in place, defects can be effectively traced and categorised. This can provide very useful insights to their root cause and how this can be avoided in future projects.
Experimental response function of NaI(Tl) scintillation detector for gamma photons and tomographic measurements for defect detection

International Nuclear Information System (INIS)

Sharma, Amandeep; Singh, Karamjit; Singh, Bhajan; Sandhu, B.S.

2011-01-01

The response function of gamma detector is an important factor for spectrum analysis because some photons and secondary electrons may escape the detector volume before fully depositing their energy, of course destroys the ideal delta function response. An inverse matrix approach, for unfolding of observed pulse-height distribution to a true photon spectrum, is used for construction of experimental response function by formulating a 40 x 40 matrix with bin mesh (E 1/2 ) of 0.025 (MeV) 1/2 for the present measurements. A tomographic scanner system, operating in a non-destructive and non-invasive way, is also presented for inspection of density variation in any object. The incoherent scattered intensity of 662 keV gamma photons, obtained by unfolding (deconvolution) the experimental pulse-height distribution of NaI(Tl) scintillation detector, provides the desired information. The method is quite sensitive, for showing inclusion of medium Z (atomic number) material (iron) in low Z material (aluminium) and detecting a void of ∼2 mm in size for iron block, to investigate the inhomogeneities in the object. Also, the grey scale images (using 'MATLAB') are shown to visualise the presence of defects/inclusion in metal samples.
Defects and properties of cadmium oxide based transparent conductors

International Nuclear Information System (INIS)

Yu, Kin Man; Detert, D. M.; Dubon, O. D.; Chen, Guibin; Zhu, Wei; Liu, Chaoping; Grankowska, S.; Hsu, L.; Walukiewicz, Wladek

2016-01-01

Transparent conductors play an increasingly important role in a number of semiconductor technologies. This paper reports on the defects and properties of Cadmium Oxide, a transparent conducting oxide which can be potentially used for full spectrum photovoltaics. We carried out a systematic investigation on the effects of defects in CdO thin films undoped and intentionally doped with In and Ga under different deposition and annealing conditions. We found that at low growth temperatures (<200 °C), sputter deposition tends to trap both oxygen vacancies and compensating defects in the CdO film resulting in materials with high electron concentration of ∼2 × 10 20 /cm 3 and mobility in the range of 40–100 cm 2 /V s. Thermal annealing experiments in different ambients revealed that the dominating defects in sputtered CdO films are oxygen vacancies. Oxygen rich CdO films grown by sputtering with increasing O 2 partial pressure in the sputter gas mixture results in films with resistivity from ∼4 × 10 −4 to >1 Ω cm due to incorporation of excess O in the form of O-related acceptor defects, likely to be O interstitials. Intentional doping with In and Ga donors leads to an increase of both the electron concentration and the mobility. With proper doping CdO films with electron concentration of more than 10 21 cm −3 and electron mobility higher than 120 cm 2 /V s can be achieved. Thermal annealing of doped CdO films in N 2 ambient can further improve the electrical properties by removing native acceptors and improving film crystallinity. Furthermore, the unique doping behavior and electrical properties of CdO were explored via simulations based on the amphoteric defect model. A comparison of the calculations and experimental results show that the formation energy of native donors and acceptors at the Fermi stabilization energy is ∼1 eV and that the mobility of sputtered deposited CdO is limited by a background acceptor concentration of
Defects and properties of cadmium oxide based transparent conductors

Energy Technology Data Exchange (ETDEWEB)

Yu, Kin Man, E-mail: kinmanyu@cityu.edu.hk [Department of Physics and Materials Science, City University of Hong Kong, Kowloon (Hong Kong); Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Detert, D. M.; Dubon, O. D. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Materials Science and Engineering, University of California, Berkeley, California 94720 (United States); Chen, Guibin [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Physics Department and Jiangsu Key Laboratory for Chemistry of Low Dimensional Materials, Huaiyin Normal University, Jiangsu 223300 (China); Zhu, Wei [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Department of Physics and The Center for Physical Experiments, University of Science and Technology of China, Hefei, Anhui 230026 (China); Liu, Chaoping [Department of Physics and Materials Science, City University of Hong Kong, Kowloon (Hong Kong); Grankowska, S. [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Institute of Experimental Physics (IEP UW), Warsaw University, Warsaw (Poland); Hsu, L. [Department of Postsecondary Teaching and Learning, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Walukiewicz, Wladek [Materials Sciences Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States)

2016-05-14

Transparent conductors play an increasingly important role in a number of semiconductor technologies. This paper reports on the defects and properties of Cadmium Oxide, a transparent conducting oxide which can be potentially used for full spectrum photovoltaics. We carried out a systematic investigation on the effects of defects in CdO thin films undoped and intentionally doped with In and Ga under different deposition and annealing conditions. We found that at low growth temperatures (<200 °C), sputter deposition tends to trap both oxygen vacancies and compensating defects in the CdO film resulting in materials with high electron concentration of ∼2 × 10{sup 20}/cm{sup 3} and mobility in the range of 40–100 cm{sup 2}/V s. Thermal annealing experiments in different ambients revealed that the dominating defects in sputtered CdO films are oxygen vacancies. Oxygen rich CdO films grown by sputtering with increasing O{sub 2} partial pressure in the sputter gas mixture results in films with resistivity from ∼4 × 10{sup −4} to >1 Ω cm due to incorporation of excess O in the form of O-related acceptor defects, likely to be O interstitials. Intentional doping with In and Ga donors leads to an increase of both the electron concentration and the mobility. With proper doping CdO films with electron concentration of more than 10{sup 21 }cm{sup −3} and electron mobility higher than 120 cm{sup 2}/V s can be achieved. Thermal annealing of doped CdO films in N{sub 2} ambient can further improve the electrical properties by removing native acceptors and improving film crystallinity. Furthermore, the unique doping behavior and electrical properties of CdO were explored via simulations based on the amphoteric defect model. A comparison of the calculations and experimental results show that the formation energy of native donors and acceptors at the Fermi stabilization energy is ∼1 eV and that the mobility of sputtered deposited CdO is limited
Crystal defect studies using x-ray diffuse scattering

Energy Technology Data Exchange (ETDEWEB)

Larson, B.C.

1980-01-01

Microscopic lattice defects such as point (single atom) defects, dislocation loops, and solute precipitates are characterized by local electronic density changes at the defect sites and by distortions of the lattice structure surrounding the defects. The effect of these interruptions of the crystal lattice on the scattering of x-rays is considered in this paper, and examples are presented of the use of the diffuse scattering to study the defects. X-ray studies of self-interstitials in electron irradiated aluminum and copper are discussed in terms of the identification of the interstitial configuration. Methods for detecting the onset of point defect aggregation into dislocation loops are considered and new techniques for the determination of separate size distributions for vacancy loops and interstitial loops are presented. Direct comparisons of dislocation loop measurements by x-rays with existing electron microscopy studies of dislocation loops indicate agreement for larger size loops, but x-ray measurements report higher concentrations in the smaller loop range. Methods for distinguishing between loops and three-dimensional precipitates are discussed and possibilities for detailed studies considered. A comparison of dislocation loop size distributions obtained from integral diffuse scattering measurements with those from TEM show a discrepancy in the smaller sizes similar to that described above.
Crystal defect studies using x-ray diffuse scattering

International Nuclear Information System (INIS)

Larson, B.C.

1980-01-01

Microscopic lattice defects such as point (single atom) defects, dislocation loops, and solute precipitates are characterized by local electronic density changes at the defect sites and by distortions of the lattice structure surrounding the defects. The effect of these interruptions of the crystal lattice on the scattering of x-rays is considered in this paper, and examples are presented of the use of the diffuse scattering to study the defects. X-ray studies of self-interstitials in electron irradiated aluminum and copper are discussed in terms of the identification of the interstitial configuration. Methods for detecting the onset of point defect aggregation into dislocation loops are considered and new techniques for the determination of separate size distributions for vacancy loops and interstitial loops are presented. Direct comparisons of dislocation loop measurements by x-rays with existing electron microscopy studies of dislocation loops indicate agreement for larger size loops, but x-ray measurements report higher concentrations in the smaller loop range. Methods for distinguishing between loops and three-dimensional precipitates are discussed and possibilities for detailed studies considered. A comparison of dislocation loop size distributions obtained from integral diffuse scattering measurements with those from TEM show a discrepancy in the smaller sizes similar to that described above
Reduction in Defect Content of ODS Alloys

Energy Technology Data Exchange (ETDEWEB)

Ritherdon, J

2001-05-15

The work detailed within this report is a continuation of earlier work carried out under contract number 1DX-SY382V. The earlier work comprises a literature review of the sources and types of defects found principally in Fe-based ODS alloys as well as experimental work designed to identify defects in the prototype ODS-Fe{sub 3}Al alloy, deduce their origins and to recommend methods of defect reduction. The present work is an extension of the experimental work already reported and concentrates on means of reduction of defects already identified rather than the search for new defect types. This report also includes results gathered during powder separation trials, conducted by the University of Groningen, Netherlands and coordinated by the University of Liverpool, involving the separation of different metallic powders in terms of their differing densities. The scope and objectives of the present work were laid out in the technical proposal ''Reduction in Defect Content in ODS Alloys-III''. All the work proposed in the ''Statement of Work'' section of the technical proposal has been carried out and all work extra to the ''Statement of Work'' falls within the context of an ODS-Fe{sub 3}Al alloy of improved overall quality and potential creep performance in the consolidated form. The outturn of the experimental work performed is reported in the following sections.
Fatal ammonia toxicity in an adult due to an undiagnosed urea cycle defect: under-recognition of ornithine transcarbamylase deficiency.

Science.gov (United States)

Thurlow, Vanessa R; Asafu-Adjaye, Michelle; Agalou, Stamatina; Rahman, Yusof

2010-05-01

There is a lack of awareness of acutely presenting inborn errors of metabolism in adults, of which the X-linked urea cycle defect ornithine transcarbamylase (OTC) deficiency is an example, many comparatively mild mutations having been identified. In male hemizygotes clinical manifestations and age at presentation vary and depend on the mutation. In female heterozygotes the clinical spectrum depends on the extent to which the abnormal gene is expressed. Milder versions of the defect may not cause clear clinical symptoms and may remain unrecognized until the person is subjected to an unusually high nitrogen load when they develop severe hyperammonaemia. During acute episodes liver enzymes may be normal or only slightly elevated and occasionally accompanied by coagulopathy, but the key finding is hyperammonaemia. Boys with these milder forms may exhibit abnormal behaviour and be diagnosed with attention deficit hyperactivity disorder. This case illustrates how late presentation of OTC deficiency in a non-specialist centre can be difficult to differentiate from drug abuse, psychiatric illness or encephalopathy. Failure to measure blood ammonia in adults with unexplained key symptoms - particularly prolonged vomiting without diarrhoea and altered mental state/hallucinations, or to recognize the significance of elevated blood ammonia without evidence of liver decompensation can lead to delayed or missed diagnosis.
The Radiological Diagnosis of Defects of the Skull Vault

African Journals Online (AJOL)

scalp and its inner relationship to meninges and brain. Brain lesions which produce skull defects usually present as brain lesions and scalp lesions which produce skull defects always present as scalp lesions. This leave" us with the same general principle, that, though there may be 40 more or less common diseases which ...
Spectrum Of Inherited Metabolic Disorders In Pakistani Children Presenting At A Tertiary Care Centre

International Nuclear Information System (INIS)

Cheema, H. A.; Malik, H. S.; Parkash, A.; Fayyaz, Z.

2016-01-01

Objective: To determine the frequency, presentation and outcome of various inherited metabolic diseases in children presenting in a tertiary care hospital, Lahore, Pakistan. Study Design: An observational study. Place and Duration of Study: Gastroenterology, Hepatology and Nutrition Department of The Children Hospital and Institute of Child Health, Lahore, from January 2011 to October 2014. Methodology: All children aged < 14 years with high suspicion of a metabolic disorder were inducted. Routine and radiological investigation were carried out at the study place. Comprehensive diagnostic testing of particular metabolic disorder was sent abroad. Those with a specific metabolic disorder were included in the study while those with normal metabolic work-up were excluded. All data was collected on preformed proforma. Result: A total of 239 patients were enrolled. Nineteen different types of inherited metabolic disorders were diagnosed in 180 patients; age ranged from 8 days to 14 years. Consanguinity was positive in 175 (97 percentage) among the parents of the affected children, with previously affected siblings in 64 (35.5 percentage). The most frequent disorders were inherited disorders of carbohydrate metabolism (92, 51 percentage), lipid storage disease (59, 32.7 percentage), organic acidemia and energy defects (18, 10 percentage), amino acid disorder (6, 3.3 percentage), and miscellaneous (4, 2.2 percentage). Fifty-eight (32.2 percentage) presented with acute metabolic crisis, 28 (15.5 percentage) patients presented with early onset liver failure, and 24 (13.3 percentage) with mental retardation. Out of these, 16 (8.8 percentage) expired. Conclusion: Glycogen storage disorders being the commonest followed by Gaucher disease and Galactosemia. The associated complications resulted in high morbidity and mortality. (author)
a Positron 2D-ACAR Study of the Silicon-Dioxide Interface and the Point Defects in the Semi-Insulating Gallium Arsenide

Science.gov (United States)

Peng, Jianping

The SiO_2-Si system has been the subject of extensive study for several decades. Particular interest has been paid to the interface between Si single crystal and the amorphous SiO_2 which determines the properties and performances of devices. This is significant because of the importance of Si technology in the semiconductor industry. The development of the high-intensity slow positron beam at Brookhaven National Laboratory make it possible to study this system for the first time using the positron two-dimensional angular correlation of annihilation radiation (2D-ACAR) technique. 2D-ACAR is a well established and is a non-destructive microscopic probe for studying the electronic structure of materials, and for doing the depth-resolved measurements. Some unique information was obtained from the measurements performed on the SiO_2-Si system: Positronium (Ps) atoms formation and trapping in microvoids in both oxide and interface regions; and positron annihilation at vacancy-like defects in the interface region which can be attributed to the famous Pb centers. The discovery of the microvoids in the interface region may have some impact on the fabrication of the next generation electronic devices. Using the conventional 2D-ACAR setup with a ^{22}Na as positron source, we also studied the native arsenic (As) vacancy in the semi -insulating gallium-arsenide (SI-GaAs), coupled with in situ infrared light illumination. The defect spectrum was obtained by comparing the spectrum taken without photo -illumination to the spectrum taken with photo-illumination. The photo-illumination excited electrons from valence band to the defect level so that positrons can become localized in the defects. The two experiments may represent a new direction of the application of positron 2D-ACAR technique on the solid state physics and materials sciences.
Electronic states of zigzag graphene nanoribbons with edges reconstructed with topological defects

Energy Technology Data Exchange (ETDEWEB)

Pincak, R., E-mail: pincak@saske.sk [Institute of Experimental Physics, Slovak Academy of Sciences, Watsonova 47, 043 53 Kosice (Slovakia); Bogoliubov Laboratory of Theoretical Physics, Joint Institute for Nuclear Research, 141980 Dubna, Moscow Region (Russian Federation); Smotlacha, J., E-mail: smota@centrum.cz [Bogoliubov Laboratory of Theoretical Physics, Joint Institute for Nuclear Research, 141980 Dubna, Moscow Region (Russian Federation); Faculty of Nuclear Sciences and Physical Engineering, Czech Technical University, Brehova 7, 110 00 Prague (Czech Republic); Osipov, V.A., E-mail: osipov@theor.jinr.ru [Bogoliubov Laboratory of Theoretical Physics, Joint Institute for Nuclear Research, 141980 Dubna, Moscow Region (Russian Federation)

2015-10-15

The energy spectrum and electronic density of states (DOS) of zigzag graphene nanoribbons with edges reconstructed with topological defects are investigated within the tight-binding method. In case of the Stone–Wales zz(57) edge the low-energy spectrum is markedly changed in comparison to the pristine zz edge. We found that the electronic DOS at the Fermi level is different from zero at any width of graphene nanoribbons. In contrast, for ribbons with heptagons only at one side and pentagons at another one the energy gap at the Fermi level is open and the DOS is equal to zero. The reason is the influence of uncompensated topological charges on the localized edge states, which are topological in nature. This behavior is similar to that found for the structured external electric potentials along the edges.
Characterization of defects in metals by positron-annihilation spectroscopy

International Nuclear Information System (INIS)

Siegel, R.W.

1981-10-01

The application of positron-annihilation spectroscopy (PAS) to the characterization and study of defects in metals has grown rapidly and increasingly useful in recent years. Owing to the ability of the positron to annihilate from a variety of defect-trapped states in metals, PAS can yield defect-specific information which, by itself or in conjunction with more traditional experimental techniques, has already made a significant impact upon our knowledge regarding lattice defect properties in metals. This has been especially true for vacancy defets, as a result of the positron's affinity for lower-than-average electron-density regions in the metal. The physical basis for the positron annihilation techniques is presented in this paper; and the experimental techniques, lifetime, Doppler broadening, and angular correlation, are briefly described and compared with respect to the information that can be obtained from each of them. A number of examples of the application of PAS to the characterization of atomic defects and their agglomerates are presented. The particular examples, chosen from the areas of equilibrium vacancy formation and atomic-defect recovery, were selected with a view toward elucidating the particular advantages of PAS over more traditional defect-characterization techniques. Limitations of PAS are also pointed out. 98 references
Quantum computing with defects

Science.gov (United States)

Varley, Joel

2011-03-01

The development of a quantum computer is contingent upon the identification and design of systems for use as qubits, the basic units of quantum information. One of the most promising candidates consists of a defect in diamond known as the nitrogen-vacancy (NV-1) center, since it is an individually-addressable quantum system that can be initialized, manipulated, and measured with high fidelity at room temperature. While the success of the NV-1 stems from its nature as a localized ``deep-center'' point defect, no systematic effort has been made to identify other defects that might behave in a similar way. We provide guidelines for identifying other defect centers with similar properties. We present a list of physical criteria that these centers and their hosts should meet and explain how these requirements can be used in conjunction with electronic structure theory to intelligently sort through candidate systems. To elucidate these points, we compare electronic structure calculations of the NV-1 center in diamond with those of several deep centers in 4H silicon carbide (SiC). Using hybrid functionals, we report formation energies, configuration-coordinate diagrams, and defect-level diagrams to compare and contrast the properties of these defects. We find that the NC VSi - 1 center in SiC, a structural analog of the NV-1 center in diamond, may be a suitable center with very different optical transition energies. We also discuss how the proposed criteria can be translated into guidelines to discover NV analogs in other tetrahedrally coordinated materials. This work was performed in collaboration with J. R. Weber, W. F. Koehl, B. B. Buckley, A. Janotti, C. G. Van de Walle, and D. D. Awschalom. This work was supported by ARO, AFOSR, and NSF.
Effects of in-cascade defect clustering on near-term defect evolution

Energy Technology Data Exchange (ETDEWEB)

Heinisch, H.L. [Pacific Northwest National Lab., Richland, WA (United States)

1997-08-01

The effects of in-cascade defect clustering on the nature of the subsequent defect population are being studied using stochastic annealing simulations applied to cascades generated in molecular dynamics (MD) simulations. The results of the simulations illustrates the strong influence of the defect configuration existing in the primary damage state on subsequent defect evolution. The large differences in mobility and stability of vacancy and interstitial defects and the rapid one-dimensional diffusion of small, glissile interstitial loops produced directly in cascades have been shown to be significant factors affecting the evolution of the defect distribution. In recent work, the effects of initial cluster sizes appear to be extremely important.
Test and Diagnosis for Small-Delay Defects

CERN Document Server

Tehranipoor, Mohammad; Chakrabarty, Krishnendu

2012-01-01

This book introduces new techniques for detecting and diagnosing small-delay defects (SDD) in integrated circuits. Although this sort of timing defect is commonly found in integrated circuits manufactured with nanometer technology, this will be the first book to introduce effective and scalable methodologies for screening and diagnosing small-delay defects, including important parameters such as process variations, crosstalk, and power supply noise. This book presents new techniques and methodologies to improve overall SDD detection with very small pattern sets. These methods can result in pattern counts as low as a traditional 1-detect pattern set and long path sensitization and SDD detection similar to or even better than n-detect or timing-aware pattern sets. The important design parameters and pattern-induced noises such as process variations,power supply noise (PSN) and crosstalk are taken into account in the methodologies presented. A diagnostic flow is also presented to identify whether the failure is ...
Mechanical properties of highly defective graphene: from brittle rupture to ductile fracture.

Science.gov (United States)

Xu, Lanqing; Wei, Ning; Zheng, Yongping

2013-12-20

Defects are generally believed to deteriorate the superlative performance of graphene-based devices but may also be useful when carefully engineered to tailor the local properties and achieve new functionalities. Central to most defect-associated applications is the defect coverage and arrangement. In this work, we investigate, by molecular dynamics simulations, the mechanical properties and fracture dynamics of graphene sheets with randomly distributed vacancies or Stone-Wales defects under tensile deformations over a wide defect coverage range. With defects presented, an sp-sp(2) bonding network and an sp-sp(2)-sp(3) bonding network are observed in vacancy-defected and Stone-Wales-defected graphene, respectively. The ultimate strength degrades gradually with increasing defect coverage and saturates in the high-ratio regime, whereas the fracture strain presents an unusual descending-saturating-improving trend. In the dense vacancy defect situation, the fracture becomes more plastic and super-ductility is observed. Further fracture dynamics analysis reveals that the crack trapping by sp-sp(2) and sp-sp(2)-sp(3) rings and the crack-tip blunting account for the ductile fracture, whereas geometric rearrangement on the entire sheet for vacancy defects and geometric rearrangement on the specific defect sites for Stone-Wales defects account for their distinctive rules of the evolution of the fracture strain.

A study of defects in diamond

International Nuclear Information System (INIS)

Hunt, D.C.

1999-01-01

Defects, intrinsic and extrinsic, in natural and synthetic diamond, have been studied using Electron Paramagnetic Resonance (EPR) and optical absorption techniques. EPR measurements have been used in conjunction with infrared absorption to identify the defect-induced one-phonon infrared spectra produced by ionised single substitutional nitrogen, N s + . This N s + spectrum is characterised by a sharp peak at the Raman energy, 1332 cm -1 , accompanied by several broader resonances at 950(5), 1050(5), and 1095(5) cm -1 . Detailed concentration measurements show that a concentration of 5.5(5) ppm gives rise to an absorption of 1 cm -1 at 1332 cm -1 . The optical absorption band ND1, identified as the negative vacancy (V - ), is frequently used by diamond spectroscopists to measure the concentration of V - . Isoya has identified V - in the EPR spectra of irradiated diamond. The accuracy of EPR in determining concentrations, has been used to correlate the integrated absorption of the ND1 zero-phonon line to the concentration of V - centres. The parameter derived from this correlation is ∼16 times smaller than the previously accepted value obtained by indirect methods. A systematic study has been made - using EPR and optical absorption techniques - of synthetic type IIa diamonds, which have been irradiated with 2 MeV electrons in a specially developed dewar, allowing irradiation down to a measured sample temperature of 100K. Measurement of defect creation rates of the neutral vacancy and EPR defects, show a radical difference in the production rate of the EPR defect R2 between irradiation with the sample held at 100K and 350K. At 100K its production rate is 1.1(1) cm -1 , ∼10 times greater that at 350K. Observation of the di- -split interstitial (Ri) after irradiation at 100K proves the self-interstitial in diamond must be mobile at 100K, under the conditions of irradiation. Further study of the properties of the R2 defect (the most dominant EPR after electron
Dirichlet topological defects

International Nuclear Information System (INIS)

Carroll, S.M.; Trodden, M.

1998-01-01

We propose a class of field theories featuring solitonic solutions in which topological defects can end when they intersect other defects of equal or higher dimensionality. Such configurations may be termed open-quotes Dirichlet topological defects,close quotes in analogy with the D-branes of string theory. Our discussion focuses on defects in scalar field theories with either gauge or global symmetries, in 3+1 dimensions; the types of defects considered include walls ending on walls, strings on walls, and strings on strings. copyright 1998 The American Physical Society
Bartter and Gitelman syndromes: Spectrum of clinical manifestations caused by different mutations

Science.gov (United States)

Al Shibli, Amar; Narchi, Hassib

2015-01-01

Bartter and Gitelman syndromes (BS and GS) are inherited disorders resulting in defects in renal tubular handling of sodium, potassium and chloride. Previously considered as genotypic and phenotypic heterogeneous diseases, recent evidence suggests that they constitute a spectrum of disease caused by different genetic mutations with the molecular defects of chloride reabsorption originating at different sites of the nephron in each condition. Although they share some characteristic metabolic abnormalities such as hypokalemia, metabolic alkalosis, hyperplasia of the juxtaglomerular apparatus with hyperreninemia, hyperaldosteronism, the clinical and laboratory manifestations may not always allow distinction between them. Diuretics tests, measuring the changes in urinary fractional excretion of chloride from baseline after administration of either hydrochlorothiazide or furosemide show very little change (< 2.3%) in the fractional excretion of chloride from baseline in GS when compared with BS, except when BS is associated with KCNJ1 mutations where a good response to both diuretics exists. The diuretic test is not recommended for infants or young children with suspected BS because of a higher risk of volume depletion in such children. Clinical symptoms and biochemical markers of GS and classic form of BS (type III) may overlap and thus genetic analysis may specify the real cause of symptoms. However, although genetic analysis is available, its use remains limited because of limited availability, large gene dimensions, lack of hot-spot mutations, heavy workup time and costs involved. Furthermore, considerable overlap exists between the different genotypes and phenotypes. Although BS and GS usually have distinct presentations and are associated with specific gene mutations, there remains considerable overlap between their phenotypes and genotypes. Thus, they are better described as a spectrum of clinical manifestations caused by different gene mutations. PMID:26140272
The role of point defects and defect complexes in silicon device processing. Summary report and papers

Energy Technology Data Exchange (ETDEWEB)

Sopori, B.; Tan, T.Y.

1994-08-01

This report is a summary of a workshop hold on August 24--26, 1992. Session 1 of the conference discussed characteristics of various commercial photovoltaic silicon substrates, the nature of impurities and defects in them, and how they are related to the material growth. Session 2 on point defects reviewed the capabilities of theoretical approaches to determine equilibrium structure of defects in the silicon lattice arising from transitional metal impurities and hydrogen. Session 3 was devoted to a discussion of the surface photovoltaic method for characterizing bulk wafer lifetimes, and to detailed studies on the effectiveness of various gettering operations on reducing the deleterious effects of transition metals. Papers presented at the conference are also included in this summary report.
Tritium releases, birth defects and infant deaths

International Nuclear Information System (INIS)

1991-01-01

The AECB has published a report 'Tritium releases from the Pickering Nuclear Generating Station and Birth Defects and Infant Mortality in Nearby Communities 1971-1988' (report number INFO-0401). This presents the results of a detailed analysis of deaths and birth defects occurring in infants born to mothers living in the area (25 Km radius) of the Pickering nuclear power plant, over an 18-year period. The analysis looked at the frequency of these defects and deaths in comparison to the general rate for Ontario, and also in relation to airborne and waterborne releases of tritium from the power plant. The overall conclusion was that the rates of infant death and birth defects were generally not higher in the study population than in all of Ontario. There was no prevalent relationship between these deaths and defects and tritium releases measured either at the power plant or by ground monitoring stations t some distance from the facility
Morning glory disc anomaly, midline cranial defects and abnormal carotid circulation: an association worth looking for

International Nuclear Information System (INIS)

Quah, Boon Long; Hamilton, Jill; Blaser, Susan; Heon, Elise; Tehrani, Nasrin N.

2005-01-01

We report on a 4-year-old boy who presented to the ophthalmology department for assessment of convergent strabismus. Ophthalmic examination showed a left morning glory optic disc anomaly and retinal detachment. Plain films obtained for investigation of short stature prior to ophthalmic examination revealed delayed bone age. Ophthalmological findings prompted CT and MRI imaging and angiographic investigations. Midline cranial defects and abnormal carotid circulation were identified. These findings may be associated with morning glory optic disc anomaly, and their association is often under-recognized. It is important that clinicians and radiologists be aware of this spectrum of disorders, as the vascular abnormalities may predispose the patient to transient ischemic attacks and strokes. Growth delay may result from hypopituitarism. (orig.)
Morning glory disc anomaly, midline cranial defects and abnormal carotid circulation: an association worth looking for

Energy Technology Data Exchange (ETDEWEB)

Quah, Boon Long [Kandang Kerbau Women' s and Children' s Hospital, Singapore National Eye Centre, Department of Ophthalmology (Singapore); Hamilton, Jill [Hospital for Sick Children, Department of Paediatrics, Toronto, ON (Canada); Blaser, Susan [Hospital for Sick Children, Department of Diagnostic Imaging, Toronto, ON (Canada); Heon, Elise; Tehrani, Nasrin N. [Hospital for Sick Children, Department of Ophthalmology and Vision Sciences, Toronto, ON (Canada)

2005-05-01

We report on a 4-year-old boy who presented to the ophthalmology department for assessment of convergent strabismus. Ophthalmic examination showed a left morning glory optic disc anomaly and retinal detachment. Plain films obtained for investigation of short stature prior to ophthalmic examination revealed delayed bone age. Ophthalmological findings prompted CT and MRI imaging and angiographic investigations. Midline cranial defects and abnormal carotid circulation were identified. These findings may be associated with morning glory optic disc anomaly, and their association is often under-recognized. It is important that clinicians and radiologists be aware of this spectrum of disorders, as the vascular abnormalities may predispose the patient to transient ischemic attacks and strokes. Growth delay may result from hypopituitarism. (orig.)
Generation of narrowband elastic waves with a fiber laser and its application to the imaging of defects in a plate.

Science.gov (United States)

Hayashi, Takahiro; Ishihara, Ken

2017-05-01

Pulsed laser equipment can be used to generate elastic waves through the instantaneous reaction of thermal expansion or ablation of the material; however, we cannot control the waveform generated by the laser in the same manner that we can when piezoelectric transducers are used as exciters. This study investigates the generation of narrowband tone-burst waves using a fiber laser of the type that is widely used in laser beam machining. Fiber lasers can emit laser pulses with a high repetition rate on the order of MHz, and the laser pulses can be modulated to a burst train by external signals. As a consequence of the burst laser emission, a narrowband tone-burst elastic wave is generated. We experimentally confirmed that the elastic waves agreed well with the modulation signals in time domain waveforms and their frequency spectra, and that waveforms can be controlled by the generation technique. We also apply the generation technique to defect imaging with a scanning laser source. In the experiments, with small laser emission energy, we were not able to obtain defect images from the signal amplitude due to low signal-to-noise ratio, whereas using frequency spectrum peaks of the tone-burst signals gave clear defect images, which indicates that the signal-to-noise ratio is improved in the frequency domain by using this technique for the generation of narrowband elastic waves. Moreover, even for defect imaging at a single receiving point, defect images were enhanced by taking an average of distributions of frequency spectrum peaks at different frequencies. Copyright © 2017 Elsevier B.V. All rights reserved.
Defect Chemistry of Oxides for Energy Applications.

Science.gov (United States)

Schweke, Danielle; Mordehovitz, Yuval; Halabi, Mahdi; Shelly, Lee; Hayun, Shmuel

2018-05-31

Oxides are widely used for energy applications, as solid electrolytes in various solid oxide fuel cell devices or as catalysts (often associated with noble metal particles) for numerous reactions involving oxidation or reduction. Defects are the major factors governing the efficiency of a given oxide for the above applications. In this paper, the common defects in oxide systems and external factors influencing the defect concentration and distribution are presented, with special emphasis on ceria (CeO 2 ) based materials. It is shown that the behavior of a variety of oxide systems with respect to properties relevant for energy applications (conductivity and catalytic activity) can be rationalized by general considerations about the type and concentration of defects in the specific system. A new method based on transmission electron microscopy (TEM), recently reported by the authors for mapping space charge defects and measuring space charge potentials, is shown to be of potential importance for understanding conductivity mechanisms in oxides. The influence of defects on gas-surface reactions is exemplified on the interaction of CO 2 and H 2 O with ceria, by correlating between the defect distribution in the material and its adsorption capacity or splitting efficiency. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
Prevalence, prenatal diagnosis and clinical features of oculo-auriculo-vertebral spectrum: a registry-based study in Europe.

LENUS (Irish Health Repository)

Barisic, Ingeborg

2014-01-08

Oculo-auriculo-vertebral spectrum is a complex developmental disorder characterised mainly by anomalies of the ear, hemifacial microsomia, epibulbar dermoids and vertebral anomalies. The aetiology is largely unknown, and the epidemiological data are limited and inconsistent. We present the largest population-based epidemiological study to date, using data provided by the large network of congenital anomalies registries in Europe. The study population included infants diagnosed with oculo-auriculo-vertebral spectrum during the 1990-2009 period from 34 registries active in 16 European countries. Of the 355 infants diagnosed with oculo-auriculo-vertebral spectrum, there were 95.8% (340\\/355) live born, 0.8% (3\\/355) fetal deaths, 3.4% (12\\/355) terminations of pregnancy for fetal anomaly and 1.5% (5\\/340) neonatal deaths. In 18.9%, there was prenatal detection of anomaly\\/anomalies associated with oculo-auriculo-vertebral spectrum, 69.7% were diagnosed at birth, 3.9% in the first week of life and 6.1% within 1 year of life. Microtia (88.8%), hemifacial microsomia (49.0%) and ear tags (44.4%) were the most frequent anomalies, followed by atresia\\/stenosis of external auditory canal (25.1%), diverse vertebral (24.3%) and eye (24.3%) anomalies. There was a high rate (69.5%) of associated anomalies of other organs\\/systems. The most common were congenital heart defects present in 27.8% of patients. The prevalence of oculo-auriculo-vertebral spectrum, defined as microtia\\/ear anomalies and at least one major characteristic anomaly, was 3.8 per 100 000 births. Twinning, assisted reproductive techniques and maternal pre-pregnancy diabetes were confirmed as risk factors. The high rate of different associated anomalies points to the need of performing an early ultrasound screening in all infants born with this disorder.European Journal of Human Genetics advance online publication, 8 January 2014; doi:10.1038\\/ejhg.2013.287.
Dual approaches for defects condensation

Energy Technology Data Exchange (ETDEWEB)

Rougemont, Romulo; Grigorio, Leonardo de Souza; Wotzasek, Clovis [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil); Guimaraes, Marcelo Santos [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil)

2009-07-01

Full text. Due to the fact that the QCD running coupling constant becomes larger as we go into the low energy (or large distance) limit of the theory, a perturbative treatment of its infrared (IR) region is impossible. In particular, a formal mathematical demonstration of color confinement and a complete physical understanding of the exact mechanism that confines quarks and gluons are two missing points in our current knowledge of the IR-QCD. It was known that due to the Meissner effect of expulsion of magnetic fields in a electric condensate that usual superconductors should confine magnetic monopoles. That point led to the conjecture that the QCD vacuum could be a condensate of chromomagnetic monopoles, a dual superconductor (DSC). Such a chromomagnetic condensate should be responsible for the dual Meissner effect which is expected to lead to the confinement of color charges immersed in this medium. In dual superconductor models of color confinement, magnetic monopoles appear as topological defects in points of the space where the abelian projection becomes singular. Also, condensation of other kinds of defects such as vortices in superfluids and line-like defects in solids are responsible for a great variety of phase transitions, which once more proves the relevance of the subject. In the present work we review two methods that allow us to approach the condensation of defects: the Kleinert Mechanism (KM) and the Julia-Toulouse Mechanism (JTM). We show that in the limit where the vortex gauge field goes to zero, which we identify as the signature of the condensation of defects in the dual picture, these are two equivalent dual prescriptions for obtaining an effective theory for a phase where defects are condensed, starting from the fundamental theory defined in the normal phase where defects are diluted. (author)
Defect forces, defect couples and path integrals in fracture mechanics

International Nuclear Information System (INIS)

Roche, R.L.

1979-07-01

In this work, it is shown that the path integrals can be introduced without any reference to the material behavior. The method is based on the definition in a continuous medium of a set of vectors and couples having the dimension of a force or a moment. More precisely, definitions are given of volume defect forces, surface defect forces, volume defect couples, and surface defect couples. This is done with the help of the stress working variation of a particule moving through the solid. The most important result is: the resultant of all the defect forces included in a volume V is the J integral on the surface surrounding V and the moment resultant is the L integral. So these integrals are defined without any assumption on the material constitutive equation. Another result is the material form of the virtual work principle - defect forces are acting like conventional forces in the conventional principles of virtual work. This lead to the introduction of the energy momentum tensor and of the associated couple stress. Application of this method is made to fracture mechanics in studying the defect forces distribution around a crack [fr
CT appearance of congenital defect resembling the Hangman's fracture

International Nuclear Information System (INIS)

Williams, J.P. III; Baker, D.H.; Miller, W.A.

1999-01-01

Purpose. Congenital defects of C2 are rare and can be confused with Hangman's fractures. CT has been advocated as aiding in differentiation between an acute fracture and congenital defects. Methods. We present a case of a 2-year-old recent accident victim, who was erroneously diagnosed by plain film and CT as having a Hangman's fracture. Results. The CT demonstrated an atypical appearance of a congenital defect. Conclusion. This case shows that the radiographic differentiation between a Hangman's fracture and a congenital defect is more difficult than previously described. (orig.)
Neural Tube Defects

Science.gov (United States)

Neural tube defects are birth defects of the brain, spine, or spinal cord. They happen in the ... that she is pregnant. The two most common neural tube defects are spina bifida and anencephaly. In ...
Cyanotic Congenital Heart Defects – literature review

Directory of Open Access Journals (Sweden)

Vlad Drăgoi

2017-11-01

Full Text Available Congenital heart defects are one of the most interesting and important chapters regarding abnormal fetal growth pathology. The objective of this article is to present a literature review for the main cyanotic congenital heart defects. The ones presented in the article are: tetralogy of Fallot, transposition of the great vessels, double outlet right ventricle, truncus arteriosus, total anomalous pulmonary venous circulation and additional information regarding very rare malformations such as pentalogy of Cantrell and Uhl anomaly. An early and precise identification of congenital heart defects is an important step in an accurate follow-up of a potential problematic pregnancy. Knowing the sonographic aspect, associated pathology and the current available treatment procedures are vital for the fetal outcome and for the physician to adapt the right management in every situation that might appear during the pregnancy and in the neonatal period.
Leak before break behaviour of austenitic and ferritic pipes containing circumferential defects

Energy Technology Data Exchange (ETDEWEB)

Stadtmueller, W.; Sturm, D.

1997-04-01

Several research projects carried out at MPA Stuttgart to investigate the Leak-before-Break (LBB) behavior of safety relevant pressure bearing components are summarized. Results presented relate to pipes containing circumferential defects subjected to internal pressure and external bending loading. An overview of the experimentally determined results for ferritic components is presented. For components containing postulated or actual defects, the dependence of the critical loading limit on the defect size is shown in the form of LBB curves. These are determined experimentally and/or by calculation for through-wall slits, and represent the boundary curve between leakage and massive fracture. For surface defects and a given bending moment and internal pressure, no fracture will occur if the length at leakage remains smaller than the critical defect length given by the LBB curve for through-wall defects. The predictive capability of engineering calculational methods are presented by way of example. The investigation programs currently underway, testing techniques, and initial results are outlined.
Mechanical properties of highly defective graphene: from brittle rupture to ductile fracture

International Nuclear Information System (INIS)

Xu, Lanqing; Wei, Ning; Zheng, Yongping

2013-01-01

Defects are generally believed to deteriorate the superlative performance of graphene-based devices but may also be useful when carefully engineered to tailor the local properties and achieve new functionalities. Central to most defect-associated applications is the defect coverage and arrangement. In this work, we investigate, by molecular dynamics simulations, the mechanical properties and fracture dynamics of graphene sheets with randomly distributed vacancies or Stone–Wales defects under tensile deformations over a wide defect coverage range. With defects presented, an sp–sp 2 bonding network and an sp–sp 2 –sp 3 bonding network are observed in vacancy-defected and Stone–Wales-defected graphene, respectively. The ultimate strength degrades gradually with increasing defect coverage and saturates in the high-ratio regime, whereas the fracture strain presents an unusual descending–saturating–improving trend. In the dense vacancy defect situation, the fracture becomes more plastic and super-ductility is observed. Further fracture dynamics analysis reveals that the crack trapping by sp–sp 2 and sp–sp 2 –sp 3 rings and the crack-tip blunting account for the ductile fracture, whereas geometric rearrangement on the entire sheet for vacancy defects and geometric rearrangement on the specific defect sites for Stone–Wales defects account for their distinctive rules of the evolution of the fracture strain. (paper)
Irradiation induced defects containing oxygen atoms in germanium crystal as studied by deep level transient spectroscopy

International Nuclear Information System (INIS)

Fukuoka, Noboru; Kambe, Yoshiyuki; Saito, Haruo; Matsuda, Koji.

1984-05-01

Deep level transient spectroscopy was applied to the electron trapping levels which are associated with the irradiation induced lattice defects in germanium crystals. The germanium crystals used in the study were doped with oxygen, antimony or arsenic and the defects were formed by electron irradiation of 1.5MeV or 10MeV. The nature of so called ''thermal defect'' formed by heat treatment at about 670K was also studied. The trapping levels at Esub(c)-0.13eV, Esub(c)-0.25eV and Esub(c)-0.29eV were found to be associated with defects containing oxygen atoms. From the experimental results the Esub(c)-0.25eV level was attributed to the germanium A-center (interstitial oxygen atom-vacancy pair). Another defect associated with the 715cm -1 infrared absorption band was found to have a trapping level at the same position at Esub(c)-0.25eV. The Esub(c)-0.23eV and Esub(c)-0.1eV levels were revealed to be associated with thermal donors formed by heat treatment at about 670K. Additional two peaks (levels) were observed in the DLTS spectrum. The annealing behavior of the levels suggests that the thermal donors originate from not a single type but several types of defects. (author)
Congenital heart defects and extracardiac malformations.

Science.gov (United States)

Rosa, Rosana Cardoso M; Rosa, Rafael Fabiano M; Zen, Paulo Ricardo G; Paskulin, Giorgio Adriano

2013-06-01

To review the association between congenital heart defects and extracardiac malformations. Scientific articles were searched in the Medline, Lilacs, and SciELO databases, using the descriptors "congenital heart disease," "congenital heart defects," "congenital cardiac malformations," "extracardiac defects," and "extracardiac malformations." All case series that specifically explored the association between congenital heart defects and extracardiac malformations were included. Congenital heart diseases are responsible for about 40% of birth defects, being one of the most common and severe malformations. Extracardiac malformations are observed in 7 to 50% of the patients with congenital heart disease, bringing a greater risk of comorbidity and mortality and increasing the risks related to heart surgery. Different studies have attempted to assess the presence of extracardiac abnormalities in patients with congenital heart disease. Among the changes described, those of the urinary tract are more often reported. However, no study has evaluated all patients in the same way. Extracardiac abnormalities are frequent among patients with congenital heart disease, and patients with these alterations may present an increased risk of morbimortality. Therefore, some authors have been discussing the importance and cost-effectiveness of screening these children for other malformations by complementary exams.
Phenotypic Spectrum in Osteogenesis Imperfecta Due to Mutations in TMEM38B: Unraveling a Complex Cellular Defect.

Science.gov (United States)

Webb, Emma A; Balasubramanian, Meena; Fratzl-Zelman, Nadja; Cabral, Wayne A; Titheradge, Hannah; Alsaedi, Atif; Saraff, Vrinda; Vogt, Julie; Cole, Trevor; Stewart, Susan; Crabtree, Nicola J; Sargent, Brandi M; Gamsjaeger, Sonja; Paschalis, Eleftherios P; Roschger, Paul; Klaushofer, Klaus; Shaw, Nick J; Marini, Joan C; Högler, Wolfgang

2017-06-01

Recessive mutations in TMEM38B cause type XIV osteogenesis imperfecta (OI) by dysregulating intracellular calcium flux. Clinical and bone material phenotype description and osteoblast differentiation studies. Natural history study in pediatric research centers. Eight patients with type XIV OI. Clinical examinations included bone mineral density, radiographs, echocardiography, and muscle biopsy. Bone biopsy samples (n = 3) were analyzed using histomorphometry, quantitative backscattered electron microscopy, and Raman microspectroscopy. Cellular differentiation studies were performed on proband and control osteoblasts and normal murine osteoclasts. Type XIV OI clinical phenotype ranges from asymptomatic to severe. Previously unreported features include vertebral fractures, periosteal cloaking, coxa vara, and extraskeletal features (muscular hypotonia, cardiac abnormalities). Proband lumbar spine bone density z score was reduced [median -3.3 (range -4.77 to +0.1; n = 7)] and increased by +1.7 (1.17 to 3.0; n = 3) following bisphosphonate therapy. TMEM38B mutant bone has reduced trabecular bone volume, osteoblast, and particularly osteoclast numbers, with >80% reduction in bone resorption. Bone matrix mineralization is normal and nanoporosity low. We demonstrate a complex osteoblast differentiation defect with decreased expression of early markers and increased expression of late and mineralization-related markers. Predominance of trimeric intracellular cation channel type B over type A expression in murine osteoclasts supports an intrinsic osteoclast defect underlying low bone turnover. OI type XIV has a bone histology, matrix mineralization, and osteoblast differentiation pattern that is distinct from OI with collagen defects. Probands are responsive to bisphosphonates and some show muscular and cardiovascular features possibly related to intracellular calcium flux abnormalities. Copyright © 2017 Endocrine Society

Radiation defect formation in two-barrier structures based on silicon

International Nuclear Information System (INIS)

Madatov, R.S.; Abbasov, F.P.; Mustafayev, Yu.M.

2013-01-01

It was developed a silicon-based photodetector with high integral sensitivity in low-wave spectrum. It was investigated the effect of gamma radiation on the mechanism of current transport in the structure of Schottky barrier type and in transitions. It is shown that the double-barrier structures can improve the photovoltaic parameters of conventional detectors. For the first time it was obtained and studied the characteristics of two-barrier structures created on the same plane. The advantages over conventional structures are shown. The annealing point is changing the structure of radiation defects and leads to their disappearance
Tetramethylene glycol mediated hydrothermal synthesis of defect-rich SnO2 nanoparticles for fast adsorption and degradation of MB dye

Science.gov (United States)

Rani, Barkha; Jadhao, Charushila Vasant; Sahu, Niroj Kumar

2018-04-01

Defect-rich pristine tin oxide nanoparticles (SnO2 NPs) with high colloidal stability have been synthesized by tetramethylene glycol (TMG) mediated hydrothermal process and characterized by XRD, TEM, Zeta Potential, PL spectroscopy and porosity measurement techniques. XRD result suggests the formation of rutile phase of SnO2 with average crystallite size of 2.65 nm. TMG act as a structure directing agent assist in the formation of network like structure of SnO2 NPs as confirmed from TEM. Significant blue shifts in the UV absorption spectrum as that of the bulk and defect bands in the PL spectrum are observed. The nanomaterial possesses very high surface area of 263.102 m2/g and large pore volume. The above properties strongly influence the photocatalytic degradation of methylene blue dye. Very fast adsorption and 96% degradation (under UV irradiation) has been achieved when 10 ppm methylene blue solutions is catalysed by 20 mg SnO2 NPs which pave the way for potential environmental application.
Ultrahigh-energy cosmic-ray spectrum

International Nuclear Information System (INIS)

Hill, C.T.; Schramm, D.N.

1985-01-01

We analyze the evolution of the ultrahigh-energy cosmic-ray spectrum upon traversing the 2.7 0 K microwave background with respect to pion photoproduction, pair-production reactions, and cosmological effects. Our approach employs exact transport equations which manifestly conserve nucleon number and embody the laboratory details of these reactions. A spectrum enhancement appears around 6 x 10 19 eV due to the ''pile-up'' of energy-degraded nucleons, and a ''dip'' occurs around 10 19 eV due to combined effects. Both of these features appear in the observational spectrum. We analyze the resulting neutrino spectrum and the effects of cosmological source distributions. We present a complete model of the ultrahigh-energy spectrum and anisotropy in reasonable agreement with observation and which predicts an observable electron-neutrino spectrum
Proceedings of the European Meeting on Positron Studies of Defects

International Nuclear Information System (INIS)

1987-01-01

The meeting dealt with both theoretical and experimental aspects of positron studies of defects using conventional and novel positron techniques. The subjects are indicated in the following headings: (1) theory of positrons in imperfect solids, (2) vacancies in metals and alloys, (3) dislocation and deformation effects, (4) amorphous alloys and fine-grained materials, (5) phase transitions, (6) precipitation phenomena, (7) gas impurity-defect interaction and irradiation effects, (8) defects in elemental semiconductors, (9) defects in compound semiconductors, (10) slow positron studies of defects, (11) defects in oxides and halides, (12) defects in molecular solids, and (13) advances in experimental techniques and data treatment. Althogether 141 contributions (invited plenary lectures, short lectures, and posters) are presented as titles with abstracts. Most of them are in INIS scope and are processed individually for the database
PREFACE: The International Workshop on Positron Studies of Defects 2014

Science.gov (United States)

Sugita, Kazuki; Shirai, Yasuharu

2016-01-01

The International Workshop on Positron Studies of Defects 2014 (PSD-14) was held in Kyoto, Japan from 14-19 September, 2014. The PSD Workshop brought together positron scientists interested in studying defects to an international platform for presenting and discussing recent results and achievements, including new experimental and theoretical methods in the field. The workshop topics can be characterized as follows: • Positron studies of defects in semiconductors and oxides • Positron studies of defects in metals • New experimental methods and equipment • Theoretical calculations and simulations of momentum distributions, positron lifetimes and other characteristics for defects • Positron studies of defects in combination with complementary methods • Positron beam studies of defects at surfaces, interfaces, in sub-surface regions and thin films • Nanostructures and amorphous materials
Fast Spectrum Reactors

CERN Document Server

Todd, Donald; Tsvetkov, Pavel

2012-01-01

Fast Spectrum Reactors presents a detailed overview of world-wide technology contributing to the development of fast spectrum reactors. With a unique focus on the capabilities of fast spectrum reactors to address nuclear waste transmutation issues, in addition to the well-known capabilities of breeding new fuel, this volume describes how fast spectrum reactors contribute to the wide application of nuclear power systems to serve the global nuclear renaissance while minimizing nuclear proliferation concerns. Readers will find an introduction to the sustainable development of nuclear energy and the role of fast reactors, in addition to an economic analysis of nuclear reactors. A section devoted to neutronics offers the current trends in nuclear design, such as performance parameters and the optimization of advanced power systems. The latest findings on fuel management, partitioning and transmutation include the physics, efficiency and strategies of transmutation, homogeneous and heterogeneous recycling, in addit...
Simulation of pattern and defect detection in periodic amplitude and phase structures using photorefractive four-wave mixing

Science.gov (United States)

Nehmetallah, Georges; Banerjee, Partha; Khoury, Jed

2015-03-01

The nonlinearity inherent in four-wave mixing in photorefractive (PR) materials is used for adaptive filtering. Examples include script enhancement on a periodic pattern, scratch and defect cluster enhancement, periodic pattern dislocation enhancement, etc. through intensity filtering image manipulation. Organic PR materials have large space-bandwidth product, which makes them useful in adaptive filtering techniques in quality control systems. For instance, in the case of edge enhancement, phase conjugation via four-wave mixing suppresses the low spatial frequencies of the Fourier spectrum of an aperiodic image and consequently leads to image edge enhancement. In this work, we model, numerically verify, and simulate the performance of a four wave mixing setup used for edge, defect and pattern detection in periodic amplitude and phase structures. The results show that this technique successfully detects the slightest defects clearly even with no enhancement. This technique should facilitate improvements in applications such as image display sharpness utilizing edge enhancement, production line defect inspection of fabrics, textiles, e-beam lithography masks, surface inspection, and materials characterization.
Radiation damage in silicon. Defect analysis and detector properties

Energy Technology Data Exchange (ETDEWEB)

Hoenniger, F.

2008-01-15

Silicon microstrip and pixel detectors are vital sensor-components as particle tracking detectors for present as well as future high-energy physics (HEP) experiments. All experiments at the large Hadron Collider (LHC) are equipped with such detectors. Also for experiments after the upgrade of the LHC (the so-called Super-LHC), with its ten times higher luminosity, or the planned International Linear Collider (ILC) silicon tracking detectors are forseen. Close to the interaction region these detectors have to face harsh radiation fields with intensities above the presently tolerable level. defect engineering of the used material, e. g. oxygen enrichment of high resistivity float zone silicon and growing of thin low resistivityepitaxial layers on Czochralski silicon substrates has been established to improve the radiation hardness of silicon sensors. This thesis focuses mainly on the investigation of radiation induced defects and their differences observed in various kinds of epitaxial silicon material. Comparisons with other materials like float zone or Czochralski silicon are added. Deep Level Transient Spectroscopy (DLTS) and Thermally Stimulated Current (TSC) measurements have been performed after {gamma}-, electron-, proton- and neutron-irradiation. The differenced in the formation of vacancy and interstitial related defects as well as so-called clustered regions were investigated for various types of irradiation. In addition to the well known defects VO{sub i}, C{sub i}O{sub i}, C{sub i}C{sub s}, VP or V{sub 2} several other defect complexes have been found and investigated. Also the material dependence of the defect introduction rates and the defect annealing behavior has been studied by isothermal and isochronal annealing experiments. Especially the IO{sub 2} defect which is an indicator for the oxygen-dimer content of the material has been investigated in detail. On the basis of radiation induced defects like the bistable donor (BD) defect and a deep
Radiation damage in silicon. Defect analysis and detector properties

International Nuclear Information System (INIS)

Hoenniger, F.

2008-01-01

Silicon microstrip and pixel detectors are vital sensor-components as particle tracking detectors for present as well as future high-energy physics (HEP) experiments. All experiments at the large Hadron Collider (LHC) are equipped with such detectors. Also for experiments after the upgrade of the LHC (the so-called Super-LHC), with its ten times higher luminosity, or the planned International Linear Collider (ILC) silicon tracking detectors are forseen. Close to the interaction region these detectors have to face harsh radiation fields with intensities above the presently tolerable level. defect engineering of the used material, e. g. oxygen enrichment of high resistivity float zone silicon and growing of thin low resistivityepitaxial layers on Czochralski silicon substrates has been established to improve the radiation hardness of silicon sensors. This thesis focuses mainly on the investigation of radiation induced defects and their differences observed in various kinds of epitaxial silicon material. Comparisons with other materials like float zone or Czochralski silicon are added. Deep Level Transient Spectroscopy (DLTS) and Thermally Stimulated Current (TSC) measurements have been performed after γ-, electron-, proton- and neutron-irradiation. The differenced in the formation of vacancy and interstitial related defects as well as so-called clustered regions were investigated for various types of irradiation. In addition to the well known defects VO i , C i O i , C i C s , VP or V 2 several other defect complexes have been found and investigated. Also the material dependence of the defect introduction rates and the defect annealing behavior has been studied by isothermal and isochronal annealing experiments. Especially the IO 2 defect which is an indicator for the oxygen-dimer content of the material has been investigated in detail. On the basis of radiation induced defects like the bistable donor (BD) defect and a deep acceptor, a model has been introduced to
Detection of paint polishing defects

Science.gov (United States)

Rebeggiani, S.; Wagner, M.; Mazal, J.; Rosén, B.-G.; Dahlén, M.

2018-06-01

Surface finish plays a major role on perceived product quality, and is the first thing a potential buyer sees. Today end-of-line repairs of the body of cars and trucks are inevitably to secure required surface quality. Defects that occur in the paint shop, like dust particles, are eliminated by manual sanding/polishing which lead to other types of defects when the last polishing step is not performed correctly or not fully completed. One of those defects is known as ‘polishing roses’ or holograms, which are incredibly hard to detect in artificial light but are clearly visible in sunlight. This paper will present the first tests with a measurement set-up newly developed to measure and analyse polishing roses. The results showed good correlations to human visual evaluations where repaired panels were estimated based on the defects’ intensity, severity and viewing angle.
Reduction in Defect Content in ODS Alloys

Energy Technology Data Exchange (ETDEWEB)

Ritherdon, J.; Jones, A.R.

2000-02-01

The work detailed within this report is a continuation of earlier work that was carried out under contract number IDX-SY382V. The earlier work comprised a literature review of the sources and types of defects found principally in Fe-based ODS alloys together with a series of experiments designed to identify defects in ODS Fe{sub 3}Al material and recommend methods of defect reduction. Defects found in the Mechanically Alloyed (MA) ODS Fe{sub 3}Al included regions of incomplete MA, porosity, intrusions and fine-grained stringers. Some defects tended to be found in association with one another e.g. intrusions and fine-grained stringers. Preliminary powder separation experiments were also performed. The scope and objectives of the present work were laid out in the technical proposal ``Reduction in Defect Content in ODS Alloys--II'' which formed the basis of amendment 3 of the current contract. The current studies were devised in the context of the preceding work with a view to extending and concluding certain experiments while exploring new avenues of investigation of defect control and reduction where appropriate. All work proposed was within the context of achieving an ODS Fe{sub 3}Al alloy of improved overall quality and potential creep performance (particularly) in the consolidated, release condition. The interim outturn of the experimental work performed is also reported.
Radiographic detection of artificial intra-bony defects in the edentulous area.

Science.gov (United States)

Van Assche, N; Jacobs, R; Coucke, W; van Steenberghe, D; Quirynen, M

2009-03-01

Since intra-bony pathologies might jeopardize implant outcome, their preoperative detection is crucial. In sixteen human cadaver bloc sections from upper and lower jaws, artificial defects with progressively increasing size (n=7) have been created. From each respective defect, analogue and digital intra-oral radiographs were taken, the latter processed via a periodontal filter and afterwards presented in black-white as well as in colour, resulting in three sets of 7 images per bloc section. Eight observers were asked to diagnosis an eventual defect on randomly presented radiographs, and at another occasion to rank each set based on the defect size. The clinicians were only able to identify a defect, when the junctional area was involved, except for bony pieces with a very homogeneous structure. For longitudinal evaluation of healing bone (e.g. after tooth extraction), colour digital images can be recommended. These observations indicate that intra-oral radiographs are not always reliable for the detection of any intra-bony defect.
Effect of gamma radiation on resting B lymphocytes. II. Functional characterization of the antigen-presentation defect

International Nuclear Information System (INIS)

Ashwell, J.D.; Jenkins, M.K.; Schwartz, R.H.

1988-01-01

The effect of radiation on three discrete Ag-presentation functions in resting B cells was examined: 1) Ag uptake and processing, 2) expression of processed Ag in the context of functional class II molecules, and 3) provision of necessary co-stimulatory, or second, signals. Analysis of radiation's effect on B cell presentation of intact vs fragmented Ag or its effect on presentation by Ag-pulsed B cells indicated that damage to Ag uptake and processing could not account for the bulk of the radiation-induced Ag-presentation defect. Experiments with phosphatidylinositol hydrolysis as an indirect measure of TCR occupancy suggested that irradiation caused a fairly rapid (within 1 to 2 h) decrease in the ability of the B cell APC to display a stimulatory combination of Ag and class II molecule. Ag dose-response analyses demonstrated that when presenting a fragment of the Ag pigeon cytochrome c to a T cell clone, 3000 rad-treated B cell APC were able to stimulate approximately 50% as much phosphatidylinositol turnover as unirradiated B cells. It was also found that, in contrast to their inability to initiate T cell proliferation, and similarly to chemically cross-linked splenocytes, heavily irradiated resting B cells plus Ag induced a state of Ag hyporesponsiveness in T cell clones. This effect on T cells had the same Ag- and MHC-specificity as did receptor occupancy required for proliferation, indicating that heavily irradiated resting B cells bear functional class II molecules. Co-culture of T cells with allogeneic B cells and syngeneic heavily irradiated B cells or chemically cross-linked splenic APC plus Ag resulted in T cell proliferation and interfered with the induction of the hyporesponsive state. This co-stimulatory function was radiosensitive in resting allogeneic B cells
Pullout Performances of Grouted Rockbolt Systems with Bond Defects

Science.gov (United States)

Xu, Chang; Li, Zihan; Wang, Shanyong; Wang, Shuren; Fu, Lei; Tang, Chunan

2018-03-01

This paper presents a numerical study on the pullout behaviour of fully grouted rockbolts with bond defects. The cohesive zone model (CZM) is adopted to model the bond-slip behaviour between the rockbolt and grout material. Tensile tests were also conducted to validate the numerical model. The results indicate that the defect length can obviously influence the load and stress distributions along the rockbolt as well as the load-displacement response of the grouted system. Moreover, a plateau in the stress distribution forms due to the bond defect. The linear limit and peak load of the load-displacement response decrease as the defect length increases. A bond defect located closer to the loaded end leads to a longer nonlinear stage in the load-displacement response. However, the peak loads measured from the specimens made with various defect locations are almost approximately the same. The peak load for a specimen with the defects equally spaced along the bolt is higher than that for a specimen with defects concentrated in a certain zone, even with the same total defect length. Therefore, the dispersed pattern of bond defects would be much safer than the concentrated pattern. For the specimen with dispersed defects, the peak load increases with an increase in the defect spacing, even if the total defect length is the same. The peak load for a grouted rockbolt system with defects increases with an increases in the bolt diameter. This work leads to a better understanding of the load transfer mechanism for grouted rockbolt systems with bond defects, and paves the way towards developing a general evaluation method for damaged rockbolt grouted systems.
On holographic defect entropy

International Nuclear Information System (INIS)

Estes, John; Jensen, Kristan; O’Bannon, Andy; Tsatis, Efstratios; Wrase, Timm

2014-01-01

We study a number of (3+1)- and (2+1)-dimensional defect and boundary conformal field theories holographically dual to supergravity theories. In all cases the defects or boundaries are planar, and the defects are codimension-one. Using holography, we compute the entanglement entropy of a (hemi-)spherical region centered on the defect (boundary). We define defect and boundary entropies from the entanglement entropy by an appropriate background subtraction. For some (3+1)-dimensional theories we find evidence that the defect/boundary entropy changes monotonically under certain renormalization group flows triggered by operators localized at the defect or boundary. This provides evidence that the g-theorem of (1+1)-dimensional field theories generalizes to higher dimensions
Tetralogy of Fallot with restrictive ventricular septal defect by accessory tricuspid leaflet tissue

OpenAIRE

Mahipat Raj Soni; Deepak A. Bohara; Ajay U. Mahajan; Pratap J. Nathani

2012-01-01

In tetralogy of Fallot septal defect is usually large because of malalignment of outlet septum, restrictive defect has been reported rarely. We present a case of tetralogy of Fallot with accessory tricuspid leaflet tissue restricting ventricular septal defect. The report includes echocardiographic and catheter images of this rare presentation of tetralogy of Fallot.
Creation of point defects in superconductors. A short review

International Nuclear Information System (INIS)

Quere, Yves; Rullier-Albenque, Florence.

1981-11-01

Many experiments have been published concerning the radiation damage in superconductors, but relatively few about the mechanisms of defect creation. A short review is presented of what is known on point defect creation in superconductors either by cold-work or by irradiation
Clinical and cytogenetic features of a Brazilian sample of patients with phenotype of oculo-auriculo-vertebral spectrum: a cross-sectional study

Directory of Open Access Journals (Sweden)

Alessandra Pawelec da Silva

Full Text Available CONTEXT AND OBJECTIVE: Oculo-auriculo-vertebral spectrum (OAVS is considered to be a defect of embryogenesis involving structures originating from the first branchial arches. Our objective was to describe the clinical and cytogenetic findings from a sample of patients with the phenotype of OAVS.DESIGN AND SETTING: Cross-sectional study in a referral hospital in southern Brazil.METHODS: The sample consisted of 23 patients who presented clinical findings in at least two of these four areas: orocraniofacial, ocular, auricular and vertebral. The patients underwent a clinical protocol and cytogenetic evaluation through high-resolution karyotyping, fluorescence in situ hybridization for 5p and 22q11 microdeletions and investigation of chromosomal instability for Fanconi anemia.RESULTS: Cytogenetic abnormalities were observed in three cases (13% and consisted of: 47,XX,+mar; mos 47,XX,+mar/46,XX; and 46,XX,t(6;10(q13; q24. We observed cases of OAVS with histories of gestational exposition to fluoxetine, retinoic acid and crack. One of our patients was a discordant monozygotic twin who had shown asymmetrical growth restriction during pregnancy. Our patients with OAVS were characterized by a broad clinical spectrum and some presented atypical findings such as lower-limb reduction defect and a tumor in the right arm, suggestive of hemangioma/lymphangioma.CONCLUSIONS: We found a wide range of clinical characteristics among the patients with OAVS. Different chromosomal abnormalities and gestational expositions were also observed. Thus, our findings highlight the heterogeneity of the etiology of OAVS and the importance of these factors in the clinical and cytogenetic evaluation of these patients.
Socio-economic background and prevalence of visual defects ...

African Journals Online (AJOL)

The thrust of this study is to examine the socio-economic background and prevalence of visual defects among students in public and private secondary schools in Calabar municipality in Cross River State. The main objective of the study is to screen for and present information on the prevalence of visual defects amongst the ...
Point defects in ZnO crystals grown by various techniques

International Nuclear Information System (INIS)

Čížek, J; Vlček, M; Hruška, P; Lukáč, F; Melikhova, O; Anwand, W; Selim, F; Hugenschmidt, Ch; Egger, W

2017-01-01

In the present work point defects in ZnO crystals were characterized by positron lifetime spectroscopy combined with back-diffusion measurement of slow positrons. Defects in ZnO crystals grown by various techniques were compared. Hydrothermally grown ZnO crystals contain defects characterized by lifetime of ≈181 ps. These defects were attributed to Zn vacancies associated with hydrogen. ZnO crystals prepared by other techniques (Bridgman, pressurized melt growth, and seeded chemical vapour transport) exhibit shorter lifetime of ≈165 ps. Positron back-diffusion studies revealed that hydrothermally grown ZnO crystals contain higher density of defects than the crystals grown by other techniques. The lowest concentration of defects was detected in the crystal grown by seeded chemical vapor transport. (paper)

Skull defect reconstruction based on a new hybrid level set.

Science.gov (United States)

Zhang, Ziqun; Zhang, Ran; Song, Zhijian

2014-01-01

Skull defect reconstruction is an important aspect of surgical repair. Historically, a skull defect prosthesis was created by the mirroring technique, surface fitting, or formed templates. These methods are not based on the anatomy of the individual patient's skull, and therefore, the prosthesis cannot precisely correct the defect. This study presented a new hybrid level set model, taking into account both the global optimization region information and the local accuracy edge information, while avoiding re-initialization during the evolution of the level set function. Based on the new method, a skull defect was reconstructed, and the skull prosthesis was produced by rapid prototyping technology. This resulted in a skull defect prosthesis that well matched the skull defect with excellent individual adaptation.
SpecNet: Spectrum Sensing Sans Frontieres

OpenAIRE

Iyer, Anand Padmanabha; Chintalapudi, Krishna; Navda, Vishnu; Ramjee, Ramachandran; Padmanabhan, Venkata N; Murthy, Chandra R

2011-01-01

While the under-utilization of licensed spectrum based on measurement studies conducted in a few developed countries has spurred lots of interest in opportunistic spectrum access, there exists no infrastructure today for measuring real-time spectrum occupancy across vast geographical regions. In this paper, we present the design and implementation of SpecNet, a ﬁrst-of-its-kind platform that allows spectrum analyzers around the world to be networked and efﬁciently used in a coordinated manner...
Defect reduction of patterned media templates and disks

Science.gov (United States)

Luo, Kang; Ha, Steven; Fretwell, John; Ramos, Rick; Ye, Zhengmao; Schmid, Gerard; LaBrake, Dwayne; Resnick, Douglas J.; Sreenivasan, S. V.

2010-05-01

Imprint lithography has been shown to be an effective technique for the replication of nano-scale features. Acceptance of imprint lithography for manufacturing will require a demonstration of defect levels commensurate with cost-effective device production. This work summarizes the results of defect inspections of hard disks patterned using Jet and Flash Imprint Lithography (J-FILTM). Inspections were performed with optical based automated inspection tools. For the hard drive market, it is important to understand the defectivity of both the template and the imprinted disk. This work presents a methodology for automated pattern inspection and defect classification for imprint-patterned media. Candela CS20 and 6120 tools from KLA-Tencor map the optical properties of the disk surface, producing highresolution grayscale images of surface reflectivity and scattered light. Defects that have been identified in this manner are further characterized according to the morphology. The imprint process was tested after optimizing both the disk cleaning and adhesion layers processes that precede imprinting. An extended imprint run was performed and both the defect types and trends are reported.
Defects in semiconductors

CERN Document Server

Romano, Lucia; Jagadish, Chennupati

2015-01-01

This volume, number 91 in the Semiconductor and Semimetals series, focuses on defects in semiconductors. Defects in semiconductors help to explain several phenomena, from diffusion to getter, and to draw theories on materials' behavior in response to electrical or mechanical fields. The volume includes chapters focusing specifically on electron and proton irradiation of silicon, point defects in zinc oxide and gallium nitride, ion implantation defects and shallow junctions in silicon and germanium, and much more. It will help support students and scientists in their experimental and theoret
Identification of biochemical features of defective Coffea arabica L. beans.

Science.gov (United States)

Casas, María I; Vaughan, Michael J; Bonello, Pierluigi; McSpadden Gardener, Brian; Grotewold, Erich; Alonso, Ana P

2017-05-01

Coffee organoleptic properties are based in part on the quality and chemical composition of coffee beans. The presence of defective beans during processing and roasting contribute to off flavors and reduce overall cup quality. A multipronged approach was undertaken to identify specific biochemical markers for defective beans. To this end, beans were split into defective and non-defective fractions and biochemically profiled in both green and roasted states. A set of 17 compounds in green beans, including organic acids, amino acids and reducing sugars; and 35 compounds in roasted beans, dominated by volatile compounds, organic acids, sugars and sugar alcohols, were sufficient to separate the defective and non-defective fractions. Unsorted coffee was examined for the presence of the biochemical markers to test their utility in detecting defective beans. Although the green coffee marker compounds were found in all fractions, three of the roasted coffee marker compounds (1-methylpyrrole, 5-methyl- 2-furfurylfuran, and 2-methylfuran) were uniquely present in defective fractions. Published by Elsevier Ltd.
Inspection of surface defects for cladding tube with laser

International Nuclear Information System (INIS)

Senoo, Shigeo; Igarashi, Miyuki; Satoh, Masakazu; Miura, Makoto

1978-01-01

This paper presents the results of experiment on mechanizing the visual inspection of surface defects of cladding tubes and improving the reliability of surface defect inspection. Laser spot inspection method was adopted for this purpose. Since laser speckle pattern includes many informations about surface aspects, the method can be utilized as an effective means for detection or classification of the surface defects. Laser beam is focussed on cladding tube surfaces, and the reflected laser beam forms typical stellar speckle patterns on a screen. Sample cladding tubes are driven in longitudinal direction, and a photo-detector is placed at a position where secondary reflection will fall on the detector. Reflected laser beam from defect-free surfaces shows uniform distribution on the detector. When the incident focussed laser beam is directed to defects, the intensity of the reflected light is reduced. In the second method, laser beam is scanned by a rotating cube mirror. As the results of experiment, the typical patterns caused by defects were observed. It is clear that reflection patterns change with the kinds of defects. The sensitivity of defect detection decreases with the increase in laser beam diameter. Surface defect detection by intensity change was also tested. (Kato, T.)
Phase-enhanced defect sensitivity for EUV mask inspection

Science.gov (United States)

Wang, Yow-Gwo; Miyakawa, Ryan; Chao, Weilun; Goldberg, Kenneth; Neureuther, Andy; Naulleau, Patrick

2014-10-01

In this paper, we present a complete study on mask blank and patterned mask inspection utilizing the Zernike phase contrast method. The Zernike phase contrast method provides in-focus inspection ability to study phase defects with enhanced defect sensitivity. However, the 90 degree phase shift in the pupil will significantly reduce the amplitude defect signal at focus. In order to detect both types of defects with a single scan, an optimized phase shift instead of 90 degree on the pupil plane is proposed to achieve an acceptable trade-off on their signal strengths. We can get a 70% of its maximum signal strength at focus for both amplitude and phase defects with a 47 degree phase shift. For SNR, the tradeoff between speckle noise and signal strength has to be considered. The SNR of phase and amplitude defects at focus can both reach 11 with 13 degree phase shift and 50% apodization. Moreover, the simulation results on patterned mask inspection of partially hidden phase defects with die-to-database inspection approach on the blank inspection tool show that the improvement of the Zernike phase method is more limited. A 40% enhancement of peak signal strength can be achieved with the Zernike phase contrast method when the defect is centered in the space, while the enhancement drops to less than 10% when it is beneath the line.
Defects in Cu(In,Ga)Se{sub 2} chalcopyrite semiconductors: a comparative study of material properties, defect states, and photovoltaic performance

Energy Technology Data Exchange (ETDEWEB)

Cao, Qing; Gunawan, Oki; Copel, Matthew; Reuter, Kathleen B; Chey, S Jay; Mitzi, David B [IBM T.J. Watson Research Center, Yorktown Heights, NY (United States); Deline, Vaughn R [IBM Almaden Resesarch Center, San Jose, CA (United States)

2011-10-15

Understanding defects in Cu(In,Ga)(Se,S){sub 2} (CIGS), especially correlating changes in the film formation process with differences in material properties, photovoltaic (PV) device performance, and defect levels extracted from admittance spectroscopy, is a critical but challenging undertaking due to the complex nature of this polycrystalline compound semiconductor. Here we present a systematic comparative study wherein varying defect density levels in CIGS films were intentionally induced by growing CIGS grains using different selenium activity levels. Material characterization results by techniques including X-ray diffraction, scanning electron microscopy, transmission electron microscopy, secondary ion mass spectrometry, X-ray photoelectron spectroscopy, and medium energy ion scattering indicate that this process variation, although not significantly affecting CIGS grain structure, crystal orientation, or bulk composition, leads to enhanced formation of a defective chalcopyrite layer with high density of indium or gallium at copper antisite defects ((In, Ga){sub Cu}) near the CIGS surface, for CIGS films grown with insufficient selenium supply. This defective layer or the film growth conditions associated with it is further linked with observed current-voltage characteristics, including rollover and crossover behavior, and a defect state at around 110 meV (generally denoted as the N1 defect) commonly observed in admittance spectroscopy. The impact of the (In, Ga){sub Cu} defects on device PV performance is also established. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)
Denonvilliers' advancement flap in congenital alar rim defects correction

Directory of Open Access Journals (Sweden)

Novaković Marijan

2009-01-01

Full Text Available Background. Alar rim defects are mostly acquired, resulting from burns, traumas or tumor excision. Sometimes they can accompany craniofacial clefts. However, isolated congenital alar defects are extremely rare. Case report. We presented two cases of congenital isolated alar cleft. The defect was closed by the use of an advancement flap, the technique described by Denonvilliers. We achieved both symmetry and appropriate thickness of the nostrils. Skin color and texture of the alar rim were excellent, with scars not excessively visible. Conclusion. Denonvilliers' z-plasty technique by using advancement flap provides both functionally and aesthetically satisfying outcome in patients with congenital alar rim defects.
Public health approach to birth defects: the Argentine experience.

Science.gov (United States)

Bidondo, María Paz; Groisman, Boris; Barbero, Pablo; Liascovich, Rosa

2015-04-01

Birth defects are a global problem, but their impact is particularly severe in low and middle income countries, where the conditions for prevention, treatment, and rehabilitation are more critical. The epidemiological transition in the infant mortality causes, and the concern of the community and the mass media about the teratogenic risk of environmental pollutants, has made health authorities aware of the importance of birth defects in Argentina. The objective of this paper is to outline those actions specifically taken in Argentina aimed at the prevention of birth defects at a national level. Firstly, we focus on birth defects in Argentina on a general basis, and then we present different laws and actions taken in terms of surveillance and public health programs, primary, secondary, and tertiary prevention. Finally, we present the Teratology Information Service "Fetal Health Line", and the genetic services organization and health professionals training by the National Center of Medical Genetics and the National Program of Genetics Network. In conclusion, in the country, several programs focus on different approaches to the problem, and the challenge is to coordinate the teamwork between them. Finally, we list tips to address birth defects from the public health perspective.
Anisotropic bias dependent transport property of defective phosphorene layer

Science.gov (United States)

Umar Farooq, M.; Hashmi, Arqum; Hong, Jisang

2015-01-01

Phosphorene is receiving great research interests because of its peculiar physical properties. Nonetheless, no systematic studies on the transport properties modified due to defects have been performed. Here, we present the electronic band structure, defect formation energy and bias dependent transport property of various defective systems. We found that the defect formation energy is much less than that in graphene. The defect configuration strongly affects the electronic structure. The band gap vanishes in single vacancy layers, but the band gap reappears in divacancy layers. Interestingly, a single vacancy defect behaves like a p-type impurity for transport property. Unlike the common belief, we observe that the vacancy defect can contribute to greatly increasing the current. Along the zigzag direction, the current in the most stable single vacancy structure was significantly increased as compared with that found in the pristine layer. In addition, the current along the armchair direction was always greater than along the zigzag direction and we observed a strong anisotropic current ratio of armchair to zigzag direction. PMID:26198318
Risk analysis of in-service pressure piping containing defects

International Nuclear Information System (INIS)

Lin, Y.C.; Xie, Y.J.; Wang, X.H.; Luo, H.

2004-01-01

The reliability of pressure piping containing defects is important in engineering. The failure probability of pressure piping containing defects may be used as a guide to the most economic deployment of resources on maintenance, inspection and repair. This paper presents a probabilistic assessment methodology for in-service pressure piping containing defects, which is especially designed for programming. It is based on three assessment codes, BS 7910, R6 and SAPV-99, considering uncertainties in operating loadings, flaw sizes, material fracture toughness and flow stress. A general sampling computation method of stress intensity factor (SIF), in the form of the relationship between SIF and axial force and bending moment and torsion, is adopted. This relationship has been successfully used in developing software, Safety Assessment System of In-service Pressure Piping Containing Flaws (SAPP-2003), to assess planar and non-planar flaws. A numerical example is presented to illustrate the application of SAPP-2003 for calculating the failure probabilities of separate defects and for the assessed pressure piping
Fibrous metaphyseal defects

International Nuclear Information System (INIS)

Ritschl, P.; Hajek, P.C.; Pechmann, U.

1989-01-01

Sixteen patients with fibrous metaphyseal defects were examined with both plain radiography and magnetic resonance (MR) imaging. Depending on the age of the fibrous metaphyseal defects, characteristic radiomorphologic changes were found which correlated well with MR images. Following intravenous Gadolinium-DTPA injection, fibrous metaphyseal defects invariably exhibited a hyperintense border and signal enhancement. (orig./GDG)
Charge mobility modification of semiconducting carbon nanotubes by intrinsic defects

International Nuclear Information System (INIS)

Bai, Hongcun; Ma, Yujia; Ma, Jinsuo; Mei, Jingnan; Tong, Yan; Ji, Yongqiang

2017-01-01

Charge carrier mobility is a central transport property in nanoscale electronics. Carbon nanotubes (CNTs) are supposed to have high carrier mobility. The preparation methods of CNTs have been greatly improved, but the defects always exist. This work presented first-principle investigations on the charge carrier mobility of carbon nanotubes containing several intrinsic defects. The charge carrier mobilities of zigzag (10, 0) tubes with Stone–Wales, mono vacant and 5/8/5 defects were studied as an example to explore the role of defects. Most carrier mobilities were decreased, but several values of mobility are unexpectedly increased upon the appearance of the defects. This interesting result is discussed based on the changes of the stretching modulus, the effective mass of the carrier and deformation potential constant induced by the defects. (paper)
A criterion and mechanism for power ramp defects

International Nuclear Information System (INIS)

Garlick, A.; Gravenor, J.G.

1978-02-01

The problem of power ramp defects in water reactor fuel pins is discussed in relation to results recently obtained from ramp experiments in the Steam Generating Heavy Water Reactor. Cladding cracks in the defected fuel pins were similar, both macro- and micro structurally, to those in unirradiated Zircaloy exposed to iodine stress-corrosion cracking (scc) conditions. Furthermore, when the measured stress levels for scc in short-term tests were taken as a criterion for ramp defects, UK fuel modelling codes were found to give a useful indication of defect probability under reactor service conditions. The likelihood of sticking between fuel and cladding is discussed and evidence presented which suggests that even at power a degree of adhesion may be expected in some fuel pins. The ramp defect mechanism is discussed in terms of fission product scc, initiation being by intergranular penetration and propagation by cleavage when suitably orientated grains are exposed to large dilatational stresses ahead of the main crack. (author)
Creation of Defects Catalogue for Nonconforming Product Identification in the Foundry Organization

Directory of Open Access Journals (Sweden)

Andrea Sütőová

2013-12-01

Full Text Available The paper deals with system of casting defects classification problematics and creation of defects catalogue in the foundry organization. There is described the value of correct defects classification and identification in the literature review and also some tools for defects classification are mentioned. Existing defects classifications and catalogues are often unusable for particular production processes and casting technology. Many foundries therefore create their own defects catalogues. The sample of created catalogue, which classifies and describes defects occuring in the aluminium foundry organization and its benefits are presented in the paper. The created catalogue primarily serves as a visual support for production operators and quality control processes.
Study on sensing property of one-dimensional ring mirror-defect photonic crystal

Science.gov (United States)

Chen, Ying; Luo, Pei; Cao, Huiying; Zhao, Zhiyong; Zhu, Qiguang

2018-02-01

Based on the photon localization and the photonic bandgap characteristics of photonic crystals (PCs), one-dimensional (1D) ring mirror-defect photonic crystal structure is proposed. Due to the introduction of mirror structure, a defect cavity is formed in the center of the photonic crystal, and then the resonant transmission peak can be obtained in the bandgap of transmission spectrum. The transfer matrix method is used to establish the relationship model between the resonant transmission peak and the structure parameters of the photonic crystals. Using the rectangular air gate photonic crystal structure, the dynamic monitoring of the detected gas sample parameters can be achieved from the shift of the resonant transmission peak. The simulation results show that the Q-value can attain to 1739.48 and the sensitivity can attain to 1642 nm ṡ RIU-1, which demonstrates the effectiveness of the sensing structure. The structure can provide certain theoretical reference for air pollution monitoring and gas component analysis.
Lead Halide Perovskite Nanocrystals in the Research Spotlight: Stability and Defect Tolerance

Science.gov (United States)

2017-01-01

This Perspective outlines basic structural and optical properties of lead halide perovskite colloidal nanocrystals, highlighting differences and similarities between them and conventional II–VI and III–V semiconductor quantum dots. A detailed insight into two important issues inherent to lead halide perovskite nanocrystals then follows, namely, the advantages of defect tolerance and the necessity to improve their stability in environmental conditions. The defect tolerance of lead halide perovskites offers an impetus to search for similar attributes in other related heavy metal-free compounds. We discuss the origins of the significantly blue-shifted emission from CsPbBr3 nanocrystals and the synthetic strategies toward fabrication of stable perovskite nanocrystal materials with emission in the red and infrared parts of the optical spectrum, which are related to fabrication of mixed cation compounds guided by Goldschmidt tolerance factor considerations. We conclude with the view on perspectives of use of the colloidal perovskite nanocrystals for applications in backlighting of liquid-crystal TV displays. PMID:28920080
DFM for maskmaking: design-aware flexible mask-defect analysis

Science.gov (United States)

Driessen, Frank A. J. M.; Westra, J.; Scheffer, M.; Kawakami, K.; Tsujimoto, E.; Yamaji, M.; Kawashima, T.; Hayashi, N.

2007-10-01

We present a novel software system that combines design intent as known by EDA designers with defect inspection results from the maskshop to analyze the severity of defects on photomasks. The software -named Takumi Design- Driven Defect Analyzer (TK-D3A)- analyzes defects by combining actions in the image domain with actions in the design domain and outputs amongst others flexible mask-repair decisions in production formats used by the maskshop. Furthermore, TK-D3A outputs clips of layout (GDS/OASIS) that can be viewed with its graphical user interface for easy review of the defects and associated repair decisions. As inputs the system uses reticle defect-inspection data (text and images) and the respective multi-layer design layouts with the definitions of criticalities. The system does not require confidential design data from IDM, Fabless Design House, or Foundry to be sent to the maskshop and it also has minimal impact on the maskshop's mode of operation. The output of TK-D3A is designed to realize value to the maskshop and its customers in the forms of: 1) improved yield, 2) reduction of delivery times of masks to customers, and 3) enhanced utilization of the maskshop's installed tool base. The system was qualified together with a major IDM on a large set of production reticles in the 90 and beyond-65 nm technology nodes of which results will be presented that show the benefits for maskmaking. The accuracy in detecting defects is extremely high. We show the system's capability to analyze defects well below the pixel resolution of all inspection tools used, as well as the capability to extract multiple types of transmission defects. All of these defects are analyzed design-criticality-aware by TK-D3A, resulting in a large fraction of defects that do not need to be repaired because they are located in non-critical or less-critical parts of the layout, or, more importantly, turn out to be repairable or negligible despite of originally being classified as
Stress and Strain State Analysis of Defective Pipeline Portion

Science.gov (United States)

Burkov, P. V.; Burkova, S. P.; Knaub, S. A.

2015-09-01

The paper presents computer simulation results of the pipeline having defects in a welded joint. Autodesk Inventor software is used for simulation of the stress and strain state of the pipeline. Places of the possible failure and stress concentrators are predicted on the defective portion of the pipeline.

Defect detection based on extreme edge of defective region histogram

Directory of Open Access Journals (Sweden)

Zouhir Wakaf

2018-01-01

Full Text Available Automatic thresholding has been used by many applications in image processing and pattern recognition systems. Specific attention was given during inspection for quality control purposes in various industries like steel processing and textile manufacturing. Automatic thresholding problem has been addressed well by the commonly used Otsu method, which provides suitable results for thresholding images based on a histogram of bimodal distribution. However, the Otsu method fails when the histogram is unimodal or close to unimodal. Defects have different shapes and sizes, ranging from very small to large. The gray-level distributions of the image histogram can vary between unimodal and multimodal. Furthermore, Otsu-revised methods, like the valley-emphasis method and the background histogram mode extents, which overcome the drawbacks of the Otsu method, require preprocessing steps and fail to use the general threshold for multimodal defects. This study proposes a new automatic thresholding algorithm based on the acquisition of the defective region histogram and the selection of its extreme edge as the threshold value to segment all defective objects in the foreground from the image background. To evaluate the proposed defect-detection method, common standard images for experimentation were used. Experimental results of the proposed method show that the proposed method outperforms the current methods in terms of defect detection.
Fatigue life assessment of free spanning pipelines containing corrosion defects

Energy Technology Data Exchange (ETDEWEB)

Lopes, Rita de Kassia D.; Campello, Georga C.; Matt, Cyntia G. da Costa; Benjamin, Adilson C.; Franciss, Ricardo [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2009-12-19

The free spanning pipelines assessment is a highlighted issue to be considered during the project and maintenance of the submarine pipelines. It is required to evaluate the fatigue life and the maximum stress due to VIV (Vortex Induced Vibration) as well as wave forces when applicable in case of shallow water. The code DNV-RP-F105 (2006) presents a methodology to calculate the fatigue life for free spanning pipelines. Such methodology however considers the pipe with no kind of defects. Nevertheless, sometimes corrosion defects are detected in periodic inspections and therefore their effects need to be taken into account in the fatigue life evaluation. The purpose of this paper thus is to present a procedure to assess the influence of the corrosion defects in the fatigue life of free spanning pipelines. Some FE analyses were performed to determine the stress concentrate factor (SCF) of the corrosion defects, which were used as input in the methodology presented in the code DNV-RP-F105 (2006). Curves of damage and so lifetime have been generated as function of the span length and water depth. As a practical application, this methodology was applied to a sub sea pipeline with several corrosion defects, localized in shallow water offshore Brazil. (author)
Gauge theory and defects in solids

CERN Document Server

Edelen, DGB

2012-01-01

This new series Mechanics and Physics of Discrete Systems aims to provide a coherent picture of the modern development of discrete physical systems. Each volume will offer an orderly perspective of disciplines such as molecular dynamics, crystal mechanics and/or physics, dislocation, etc. Emphasized in particular are the fundamentals of mechanics and physics that play an essential role in engineering applications.Volume 1, Gauge Theory and Defects in Solids, presents a detailed development of a rational theory of the dynamics of defects and damage in solids. Solutions to field e
Non destructive defect detection by spectral density analysis.

Science.gov (United States)

Krejcar, Ondrej; Frischer, Robert

2011-01-01

The potential nondestructive diagnostics of solid objects is discussed in this article. The whole process is accomplished by consecutive steps involving software analysis of the vibration power spectrum (eventually acoustic emissions) created during the normal operation of the diagnosed device or under unexpected situations. Another option is to create an artificial pulse, which can help us to determine the actual state of the diagnosed device. The main idea of this method is based on the analysis of the current power spectrum density of the received signal and its postprocessing in the Matlab environment with a following sample comparison in the Statistica software environment. The last step, which is comparison of samples, is the most important, because it is possible to determine the status of the examined object at a given time. Nowadays samples are compared only visually, but this method can't produce good results. Further the presented filter can choose relevant data from a huge group of data, which originate from applying FFT (Fast Fourier Transform). On the other hand, using this approach they can be subjected to analysis with the assistance of a neural network. If correct and high-quality starting data are provided to the initial network, we are able to analyze other samples and state in which condition a certain object is. The success rate of this approximation, based on our testing of the solution, is now 85.7%. With further improvement of the filter, it could be even greater. Finally it is possible to detect defective conditions or upcoming limiting states of examined objects/materials by using only one device which contains HW and SW parts. This kind of detection can provide significant financial savings in certain cases (such as continuous casting of iron where it could save hundreds of thousands of USD).
Multigrid and defect correction for the steady Navier-Stokes equations

NARCIS (Netherlands)

Koren, B.

1990-01-01

Theoretical and experimental convergence results are presented for nonlinear multigrid and iterative defect correction applied to finite volume discretizations of the full, steady, 2D, compressible Navier-Stokes equations. Iterative defect correction is introduced for circumventing the difficulty in
Structural defects in monocrystalline silicon: from radiation ones to growing and technological

International Nuclear Information System (INIS)

Gerasimenko, N.N.; Pavlyuchenko, M.N.; Dzhamanbalin, K.K.

2001-01-01

The systematical review of properties and conditions of radiation structures in monocrystalline silicon including own defects (elementary and complex, disordered fields) as well as defect-impurity formations is presented. The most typical examples of principle effects influence of known defects on radiation-induced processes (phase transformations, diffusion and heteration and others are considered. Experimental facts and models of silicon radiation amorphization have been analyzed in comparison of state of the radiation amorphization radiation problem of metals and alloys. The up-to-date status of the problem of the radiation defects physics are discussed, including end-of-range -, n+-, rod-like- defects. The phenomenon self-organization in crystals with defects has been considered. The examples of directed using radiation defects merged in independent trend - defects engineering - are given
From disability to ability: comprehensive rehabilitation providing a holistic functional improvement in a child with neglected neural tube defect.

Science.gov (United States)

Mishra, Kriti; Siddharth, V

2017-09-25

Neural Tube defects are one of the most common congenital disorders, presenting in a paediatric rehabilitation set-up. With its wide spectrum of clinical presentation and possible complications, the condition can significantly impact an individual's functional capacity and quality of life. The condition also affects the family of the child leaving them with a lifelong impairment to cope up with. Through this 16-year-old child, we shed light on the effects of providing rehabilitation, even at a later stage and its benefits. We also get a glimpse of difficulties in availing rehabilitation services in developing countries and the need to reach out many more neglected children like him with good functional abilities. © BMJ Publishing Group Ltd (unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.
Bi-spectrum based-EMD applied to the non-stationary vibration signals for bearing faults diagnosis.

Science.gov (United States)

Saidi, Lotfi; Ali, Jaouher Ben; Fnaiech, Farhat

2014-09-01

Empirical mode decomposition (EMD) has been widely applied to analyze vibration signals behavior for bearing failures detection. Vibration signals are almost always non-stationary since bearings are inherently dynamic (e.g., speed and load condition change over time). By using EMD, the complicated non-stationary vibration signal is decomposed into a number of stationary intrinsic mode functions (IMFs) based on the local characteristic time scale of the signal. Bi-spectrum, a third-order statistic, helps to identify phase coupling effects, the bi-spectrum is theoretically zero for Gaussian noise and it is flat for non-Gaussian white noise, consequently the bi-spectrum analysis is insensitive to random noise, which are useful for detecting faults in induction machines. Utilizing the advantages of EMD and bi-spectrum, this article proposes a joint method for detecting such faults, called bi-spectrum based EMD (BSEMD). First, original vibration signals collected from accelerometers are decomposed by EMD and a set of IMFs is produced. Then, the IMF signals are analyzed via bi-spectrum to detect outer race bearing defects. The procedure is illustrated with the experimental bearing vibration data. The experimental results show that BSEMD techniques can effectively diagnosis bearing failures. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.
Spectrum estimation method based on marginal spectrum

International Nuclear Information System (INIS)

Cai Jianhua; Hu Weiwen; Wang Xianchun

2011-01-01

FFT method can not meet the basic requirements of power spectrum for non-stationary signal and short signal. A new spectrum estimation method based on marginal spectrum from Hilbert-Huang transform (HHT) was proposed. The procession of obtaining marginal spectrum in HHT method was given and the linear property of marginal spectrum was demonstrated. Compared with the FFT method, the physical meaning and the frequency resolution of marginal spectrum were further analyzed. Then the Hilbert spectrum estimation algorithm was discussed in detail, and the simulation results were given at last. The theory and simulation shows that under the condition of short data signal and non-stationary signal, the frequency resolution and estimation precision of HHT method is better than that of FFT method. (authors)
Effects of primary recoil (PKA) energy spectrum on radiation damage in fcc metals

International Nuclear Information System (INIS)

Iwata, Tadao; Iwase, Akihiro

1997-10-01

Irradiation effects by different energetic particles such as electrons, various ions and neutrons are compared in fcc metals, particularly in Cu and Ni. It is discussed on the statistical consideration that the logarithm of the so-called PKA median energy, log T 1/2 , is a good representative to characterize the primary recoil (i.e. PKA) energy spectrum with the resultant defect production. For the irradiations of electrons, various ions and neutrons to Cu and Ni, fundamental physical quantities such as the fraction of stage I recovery, the defect production cross sections and the radiation annealing cross sections can be well scaled as a function of log T 1/2 , if the effects of the electron excitation caused by irradiating ions are excluded. Namely, all data of the respective physical quantity lie on a single continuous curve as a function of log T 1/2 . This characteristic curve is utilized to predict the damage accumulation (i.e. defect concentration) as a function of dpa in Cu and Ni with the PKA median energy as a parameter. (author)
Effects of primary recoil (PKA) energy spectrum on radiation damage in fcc metals

Energy Technology Data Exchange (ETDEWEB)

Iwata, Tadao; Iwase, Akihiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-10-01

Irradiation effects by different energetic particles such as electrons, various ions and neutrons are compared in fcc metals, particularly in Cu and Ni. It is discussed on the statistical consideration that the logarithm of the so-called PKA median energy, log T{sub 1/2}, is a good representative to characterize the primary recoil (i.e. PKA) energy spectrum with the resultant defect production. For the irradiations of electrons, various ions and neutrons to Cu and Ni, fundamental physical quantities such as the fraction of stage I recovery, the defect production cross sections and the radiation annealing cross sections can be well scaled as a function of log T{sub 1/2}, if the effects of the electron excitation caused by irradiating ions are excluded. Namely, all data of the respective physical quantity lie on a single continuous curve as a function of log T{sub 1/2}. This characteristic curve is utilized to predict the damage accumulation (i.e. defect concentration) as a function of dpa in Cu and Ni with the PKA median energy as a parameter. (author)
A first principles study of native defects in alpha-quartz

CERN Document Server

Roma, G

2003-01-01

We present a study of several neutral and charged oxygen and silicon defects in alpha-quartz. We performed plane waves pseudopotential calculations in the framework of density functional theory in the local density approximation. We will show the structures that we obtained for vacancies and interstitials in several charge states and the corresponding formation energies. We discuss the reciprocal dependence of formation energies of charged defects (and thus concentrations) and the electron chemical potential on each other and we determine the latter by iterative self-consistent solution of the equation imposing charge neutrality. Results on defect concentrations, their dependence on oxygen partial pressure, and self-doping effects are presented.
Late-Onset Non-HLH Presentations of Growth Arrest, Inflammatory Arachnoiditis, and Severe Infectious Mononucleosis, in Siblings with Hypomorphic Defects in UNC13D

Directory of Open Access Journals (Sweden)

Paul Edgar Gray

2017-08-01

Full Text Available Bi-allelic null mutations affecting UNC13D, STXBP2, or STX11 result in defects of lymphocyte cytotoxic degranulation and commonly cause familial hemophagocytic lymphohistiocytosis (FHL in early life. Patients with partial loss of function are increasingly being diagnosed after presenting with alternative features of this disease, or with HLH later in life. Here, we studied two sisters with lymphocyte degranulation defects secondary to compound heterozygote missense variants in UNC13D. The older sibling presented aged 11 with linear growth arrest and delayed puberty, 2 years prior to developing transient ischemic attacks secondary to neuroinflammation and hypogammaglobulinemia, but no FHL symptoms. Her geno-identical younger sister was initially asymptomatic but then presented at the same age with severe EBV-driven infectious mononucleosis, which was treated aggressively and did not progress to HLH. The sisters had similar natural killer cell degranulation; however, while cytotoxic activity was moderately reduced in the asymptomatic patient, it was completely absent in both siblings during active disease. Following allogeneic bone marrow transplantation at the age of 15, the older child has completely recovered NK cell cytotoxicity, is asymptomatic, and has experienced an exceptional compensatory growth spurt. Her younger sister was also successfully transplanted and is currently disease free. The current study reveals previously unappreciated manifestations of FHL in patients who inherited hypomorphic gene variants and also raises the important question of whether a threshold of minimum NK function can be defined that should protect a patient from serious disease manifestations such as HLH.
Effects of various defects on the mechanical properties of black phosphorene

Science.gov (United States)

Nguyen, Danh-Truong; Le, Minh-Quy; Nguyen, Van-Trang; Bui, Thanh-Lam

2017-12-01

The present work investigates the effects of seven types of defects on the mechanical properties of black phosphorene. Molecular dynamics finite element method with Stillinger-Weber potential is used to simulate the uniaxial tensile tests of the pristine and defective black phosphorene sheets. Young's modulus, fracture stress, and fracture strain of the pristine and defective black phosphorene sheets are estimated. Comparison of the influence of different types of defects on the mechanical response of black phosphorene is considered. Fracture mechanism of various defective black phosphorene sheets is also analyzed. It is found that effect of the defects on Young's modulus of black phosphorene is insignificant. In contrast, due to defects fracture stress and fracture strain can reduce up to 53% and 69%, respectively. Results provide a landscape on the mechanical properties of defective black phosphorene and are useful for the design of nanodevices with black phosphorene in future applications.
Investigation of Shrinkage Defect in Castings by Quantitative Ishikawa Diagram

Directory of Open Access Journals (Sweden)

Chokkalingam B.

2017-03-01

Full Text Available Metal casting process involves processes such as pattern making, moulding and melting etc. Casting defects occur due to combination of various processes even though efforts are taken to control them. The first step in the defect analysis is to identify the major casting defect among the many casting defects. Then the analysis is to be made to find the root cause of the particular defect. Moreover, it is especially difficult to identify the root causes of the defect. Therefore, a systematic method is required to identify the root cause of the defect among possible causes, consequently specific remedial measures have to be implemented to control them. This paper presents a systematic procedure to identify the root cause of shrinkage defect in an automobile body casting (SG 500/7 and control it by the application of Pareto chart and Ishikawa diagram. with quantitative Weightage. It was found that the root causes were larger volume section in the cope, insufficient feeding of riser and insufficient poured metal in the riser. The necessary remedial measures were taken and castings were reproduced. The shrinkage defect in the castings was completely eliminated.
Conductivity of epitaxial and CVD graphene with correlated line defects

DEFF Research Database (Denmark)

Radchenko, T. M.; Shylau, Artsem; Zozoulenko, I. V.

2014-01-01

Transport properties of single-layer graphene with correlated one-dimensional defects are studied theoretically using the computational model within the time-dependent real-space Kubo-Greenwood formalism. Such defects are present in epitaxial graphene, comprising atomic terraces and steps due...
Groin defects seen at extra-peritoneal laparoscopic dissection during surgical treatment of athletic pubalgia.

Science.gov (United States)

Wikiel, Krzysztof J; Eid, George M

2015-07-01

Recently new disease process, often referred to as athletic pubalgia (AP), has been acknowledged by the medical community. The patients suffering from this ailment present with unilateral or bilateral chronic groin pain associated with physical activity without a clear diagnosis of a groin hernia. Though physical therapy and medical treatments are considered first line remedies, some believe that surgical treatment may have better, quicker, and more durable outcomes and procedures aimed at groin reinforcement seem to relieve most of symptoms in the majority of the patients. Despite many surgeons consistently noting rectus insertion or adductor thinning, multiple hernia defects are often seen during dissections and the clinical significance of these findings is still not known. Between 2007 and 2011, 40 patients underwent an extra-peritoneal laparoscopic reinforcement of rectus abdominals and insertion of adductor muscles for AP. All patients underwent wide and bilateral groin dissection and the findings were cataloged. All of the patients presented with groin defects upon wide dissection. Thirty-four patients (85%) presented with small bilateral indirect inguinal defects and 28 (70%) of these patients did not have any additional defects. Five patients (12.5%) were found to have only unilateral inguinal hernia defects. One patient presented with a small direct defect. In addition to these defects, five patients (12.5%) had additional unilateral femoral hernias, whereas no patient had solitary femoral hernia defects. AP is a new diagnostic entity with poorly understood etiology. It mostly affects young active adults, often involved in competitive sports and surgical methods may be most effective at achieving the cure. In our experience all of the patients presented with groin defects, though not all were the same. It is our belief that these defects, although likely not the only component, play a significant role in the pathophysiology of AP.
Opportunistic spectrum utilization in vehicular communication networks

CERN Document Server

Cheng, Nan

2016-01-01

This brief examines current research on improving Vehicular Networks (VANETs), examining spectrum scarcity due to the dramatic growth of mobile data traffic and the limited bandwidth of dedicated vehicular communication bands and the use of opportunistic spectrum bands to mitigate congestion. It reviews existing literature on the use of opportunistic spectrum bands for VANETs, including licensed and unlicensed spectrum bands and a variety of related technologies, such as cognitive radio, WiFi and device-to-device communications. Focused on analyzing spectrum characteristics, designing efficient spectrum exploitation schemes, and evaluating the date delivery performance when utilizing different opportunistic spectrum bands, the results presented in this brief provide valuable insights on improving the design and deployment of future VANETs.
Thin-film limit formalism applied to surface defect absorption.

Science.gov (United States)

Holovský, Jakub; Ballif, Christophe

2014-12-15

The thin-film limit is derived by a nonconventional approach and equations for transmittance, reflectance and absorptance are presented in highly versatile and accurate form. In the thin-film limit the optical properties do not depend on the absorption coefficient, thickness and refractive index individually, but only on their product. We show that this formalism is applicable to the problem of ultrathin defective layer e.g. on a top of a layer of amorphous silicon. We develop a new method of direct evaluation of the surface defective layer and the bulk defects. Applying this method to amorphous silicon on glass, we show that the surface defective layer differs from bulk amorphous silicon in terms of light soaking.
Neutron spectrum unfolding: Pt. 2

International Nuclear Information System (INIS)

Matiullah; Wiyaja, D.S.; Berzonis, M.A.; Bondars, H.; Lapenas, A.A.; Kudo, K.; Majeed, A.; Durrani, S.A.

1991-01-01

In Part I of this paper, we described the use of the computer code SAIPS in neutron spectrum unfolding. Here in Part II, we present our experimental work carried out to study the shape of the neutron spectrum in different experimental channels of a 5 MW light-water cooled and moderated research reactor. The spectral neutron flux was determined using various fission foils (placed in close contact with mica track detectors) and activation detectors. From the measured activities, the neutron spectrum was unfolded by SAIPS. (author)

Magnetic-Field Induced Enhancement in the Fluorescence Yield Spectrum of Doubly Excited States in Helium

International Nuclear Information System (INIS)

Stroem, Magnus; Saathe, Conny; Agaaker, Marcus; Soederstroem, Johan; Rubensson, Jan-Erik; Stranges, Stefano; Richter, Robert; Alagia, Michele; Gorczyca, T. W.; Robicheaux, F.

2006-01-01

An influence of static magnetic fields on the fluorescence yield spectrum of He in the vicinity of the N=2 thresholds has been observed. The experimental results are in excellent agreement with predictions based on multichannel quantum defect theory, and it is demonstrated that the Rydberg electron l mixing due to the diamagnetic interaction is essential for the description of the observed fluorescence yield intensity enhancement
Defect-vectors and path integrals in fracture mechanics

International Nuclear Information System (INIS)

Roche, R.L.

1979-01-01

It seems necessary to introduce the J integral without hypothesis on material behavior. The aim of this paper is this introduction and its consequences. Successively are presented: introduction to defect-vectors and defect-momentum, definition of J(K) and J(L) integrals, equilibrium and energy momentum tensor, energetic signification of the path J and L integrals, and local aspects of the criteria based on path integrals [fr
Parameters of radiation defects in GaP and GaAssub(1-x)Psub(x) with thermostimulated current measurements

International Nuclear Information System (INIS)

Brajlovskij, E.Yu.; Marchuk, N.D.

1980-01-01

Introduction of point defects in gallium phosphide crystals and GaAssub(1-x)Psub(x) solid solutions under the action of 1 MeV electrons is studied by TSC method on Schottky barriers. The TSC spectra processing using the computer is given. In GaP crystals the dominant electron and hole traps are D-centers (Esub(c)-1.24 eV) and M-centers (Esub(v)+1.43 eV). The received level spectrum explains the compensation of conductivity of n- and p-lGaP under irradiation. It is shown that main defects observed in electron irradiated GaP are most likely phosphorus vacancies (D-center)and gallium vacancies (M-center)
Modelling water vapour permeability through atomic layer deposition coated photovoltaic barrier defects

Energy Technology Data Exchange (ETDEWEB)

Elrawemi, Mohamed, E-mail: Mohamed.elrawemi@hud.ac.uk [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom); Blunt, Liam; Fleming, Leigh [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom); Bird, David, E-mail: David.Bird@uk-cpi.com [Centre for Process Innovation Limited, Sedgefield, County Durham (United Kingdom); Robbins, David [Centre for Process Innovation Limited, Sedgefield, County Durham (United Kingdom); Sweeney, Francis [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom)

2014-11-03

Transparent barrier films such as Al{sub 2}O{sub 3} used for prevention of oxygen and/or water vapour permeation are the subject of increasing research interest when used for the encapsulation of flexible photovoltaic modules. However, the existence of micro-scale defects in the barrier surface topography has been shown to have the potential to facilitate water vapour ingress, thereby reducing cell efficiency and causing internal electrical shorts. Previous work has shown that small defects (≤ 3 μm lateral dimension) were less significant in determining water vapour ingress. In contrast, larger defects (≥ 3 μm lateral dimension) seem to be more detrimental to the barrier functionality. Experimental results based on surface topography segmentation analysis and a model presented in this paper will be used to test the hypothesis that the major contributing defects to water vapour transmission rate are small numbers of large defects. The model highlighted in this study has the potential to be used for gaining a better understanding of photovoltaic module efficiency and performance. - Highlights: • A model of water vapour permeation through barrier defects is presented. • The effect of the defects on the water vapour permeability is investigated. • Defect density correlates with water vapour permeability. • Large defects may dominate the permeation properties of the barrier film.
Stabilization of primary mobile radiation defects in MgF{sub 2} crystals

Energy Technology Data Exchange (ETDEWEB)

Lisitsyn, V.M. [National Research Tomsk Polytechnic University, pr. Lenina 30, Tomsk 634050 (Russian Federation); Lisitsyna, L.A. [State University of Architecture and Building, pl. Solyanaya 2, Tomsk 634003 (Russian Federation); Popov, A.I., E-mail: popov@ill.fr [Institute of Solid State Physics, University of Latvia, 8 Kengaraga Str., LV-1063 Riga (Latvia); Kotomin, E.A. [Institute of Solid State Physics, University of Latvia, 8 Kengaraga Str., LV-1063 Riga (Latvia); Max Planck Institute for Solid State Research, Heisenbergstr. 1, 70569 Stuttgart (Germany); Abuova, F.U.; Akilbekov, A. [L.N. Gumilyov Eurasian National University, 3 Munaitpasova Str., Astana (Kazakhstan); Maier, J. [Max Planck Institute for Solid State Research, Heisenbergstr. 1, 70569 Stuttgart (Germany)

2016-05-01

Non-radiative decay of the electronic excitations (excitons) into point defects (F–H pairs of Frenkel defects) is main radiation damage mechanism in many ionic (halide) solids. Typical time scale of the relaxation of the electronic excitation into a primary, short-lived defect pair is about 1–50 ps with the quantum yield up to 0.2–0.8. However, only a small fraction of these primary defects are spatially separated and survive after transformation into stable, long-lived defects. The survival probability (or stable defect accumulation efficiency) can differ by orders of magnitude, dependent on the material type; e.g. ∼10% in alkali halides with f.c.c. or b.c.c. structure, 0.1% in rutile MgF{sub 2} and <0.001% in fluorides MeF{sub 2} (Me: Ca, Sr, Ba). The key factor determining accumulation of stable radiation defects is stabilization of primary defects, first of all, highly mobile hole H centers, through their transformation into more complex immobile defects. In this talk, we present the results of theoretical calculations of the migration energies of the F and H centers in poorely studied MgF{sub 2} crystals with a focus on the H center stabilization in the form of the interstitial F{sub 2} molecules which is supported by presented experimental data.
Photoexcitation electron paramagnetic resonance studies on nickel-related defects in diamond

CERN Document Server

Pereira, R N; Neves, A J; Sobolev, N A

2003-01-01

Measurements of the electron paramagnetic resonance (EPR) upon photoexcitation are reported on Ni defects in diamonds grown with Ni-containing solvent/catalysts. The temperature dependence of the W8 EPR spectrum photoquenching shows that the relaxation of substitutional Ni sub s sup - upon electron ionization is very small, corroborating the interpretation that the previously reported photoinduced effects with thresholds at 2.5 and 3.0 eV correspond to two complementary photoionization transitions involving Ni sub s. Photoinduced behaviour of the NIRIM1 EPR centre favours the interstitial Ni sub i sup + model for this defect and suggests that the Ni sub i sup 0 sup / sup + level is located at 1.98 +- 0.03 eV below the conduction band. In N-doped diamond, Ni sub i is more likely to appear in the neutral state, undetectable by EPR, whereas at substitutional sites Ni sub s sup - is revealed. Observation of a strong AB2 EPR signal photoquenching and simultaneous detection of different spectral dependencies of the...
Micromagnetic simulation of exploratory magnetic logic device with missing corner defect

Energy Technology Data Exchange (ETDEWEB)

Yang, Xiaokuo, E-mail: yangxk0123@163.com; Cai, Li; Zhang, Bin; Cui, Huanqing; Zhang, Mingliang

2015-11-15

Magnetic film nanostructures are attractive components of nonvolatile magnetoresistive memories and nanomagnet logic circuits. Recently, we studied switching properties (i.e., null logic preserving) of rectangle shape nanomagnet subjected to fabrication imperfections. Specifically, we presented typical missing corner material-related imperfections and adopted an isosceles triangle to model this defect for nanomagnets. Micromagnetic simulation shows that this kind of imperfections modeling method agrees well with previous experimental observations. Using the proposed defect modeling scheme, we investigate in detail the switching characteristics of different defective stand-alone and coupled nanomagnets. The results suggest that the state transition of defective nanomagnet element highly depends on defect type and device’s aspect ratio, and the defect type B{sub d} needs the largest coercive field, while the defect type D requires the largest null field for switching. These findings can provide key technical parameters and guides for nanomagnet logic circuit design. - Highlights: • We have modeled missing corner defect issue for nanomagnet logic device. • The logic state of defective NML element highly depends on defect type and AR. • The NML device with defect type B{sub d} needs the largest coercive field to reverse state. • The defect type D in the NML devices requires the largest null field to switch.
Facts about Birth Defects

Science.gov (United States)

... label> Information For… Media Policy Makers Facts about Birth Defects Language: English (US) Español (Spanish) Recommend on ... having a baby born without a birth defect. Birth Defects Are Common Every 4 ½ minutes, a ...
High-resolution measurements and multichannel quantum defect analysis of spectral line shapes of autoionizing Rydberg series

International Nuclear Information System (INIS)

Ueda, Kiyoshi

1997-01-01

Spectral line shapes for autoionizing Rydberg series are briefly reviewed within the framework of multichannel quantum defect theory (MQDT). Recent high-resolution measurements and MQDT analysis for the spectra line shapes are reviewed for the mp 5 ( 2 P 1/2 )ns ' and nd ' J=1 odd spectra of the Ar, Kr, and Xe atoms (m=3,4,5 for Ar, Kr, and Xe) and the 3p 5 ( 2 P 1/2 )nd ' J=2 and 3 odd spectra of Ar*3p 5 4p excited atoms. Some results are also discussed for the Ca 4p( 2 P 1/2,3/2 )ns and nd J=1 odd spectrum and the Ba 5d( 2 P 5/2 )nd J=1 odd spectrum
Measurement of 235U fission spectrum-averaged cross sections and neutron spectrum adjusted with the activation data

International Nuclear Information System (INIS)

Kobayashi, Katsuhei; Kobayashi, Tooru

1992-01-01

The 235 U fission spectrum-averaged cross sections for 13 threshold reactions were measured with the fission plate (27 cm in diameter and 1.1 cm thick) at the heavy water thermal neutron facility of the Kyoto University Reactor. The Monte Carlo code MCNP was applied to check the deviation from the 235 U fission neutron spectrum due to the room-scattered neutrons, and it was found that the resultant spectrum was close to that of 235 U fission neutrons. Supplementally, the relations to derive the absorbed dose rates with the fission plate were also given using the calculated neutron spectra and the neutron Kerma factors. Finally, the present values of the fission spectrum-averaged cross sections were employed to adjust the 235 U fission neutron spectrum with the NEUPAC code. The adjusted spectrum showed a good agreement with the Watt-type fission neutron spectrum. (author)
The quantum defect: Early history and recent developments

International Nuclear Information System (INIS)

Rau, A.R.; Inokuti, M.

1997-01-01

The notion of the quantum defect is important in atomic and molecular spectroscopy and also in unifying spectroscopy with collision theory. In the latter context, the quantum defect may be viewed as an ancestor of the phase shift. However, the origin of the term open-quotes quantum defectclose quotes does not seem to be explained in standard textbooks. It occurred in a 1921 paper by Schroedinger, preceding quantum mechanics, yet giving the correct meaning as an index of the short-range interactions with the core of an atom. We present the early history of the quantum-defect idea, and sketch its recent developments. copyright 1997 American Association of Physics Teachers
Immersion lithography defectivity analysis at DUV inspection wavelength

Science.gov (United States)

Golan, E.; Meshulach, D.; Raccah, N.; Yeo, J. Ho.; Dassa, O.; Brandl, S.; Schwarz, C.; Pierson, B.; Montgomery, W.

2007-03-01

Significant effort has been directed in recent years towards the realization of immersion lithography at 193nm wavelength. Immersion lithography is likely a key enabling technology for the production of critical layers for 45nm and 32nm design rule (DR) devices. In spite of the significant progress in immersion lithography technology, there remain several key technology issues, with a critical issue of immersion lithography process induced defects. The benefits of the optical resolution and depth of focus, made possible by immersion lithography, are well understood. Yet, these benefits cannot come at the expense of increased defect counts and decreased production yield. Understanding the impact of the immersion lithography process parameters on wafer defects formation and defect counts, together with the ability to monitor, control and minimize the defect counts down to acceptable levels is imperative for successful introduction of immersion lithography for production of advanced DR's. In this report, we present experimental results of immersion lithography defectivity analysis focused on topcoat layer thickness parameters and resist bake temperatures. Wafers were exposed on the 1150i-α-immersion scanner and 1200B Scanner (ASML), defect inspection was performed using a DUV inspection tool (UVision TM, Applied Materials). Higher sensitivity was demonstrated at DUV through detection of small defects not detected at the visible wavelength, indicating on the potential high sensitivity benefits of DUV inspection for this layer. The analysis indicates that certain types of defects are associated with different immersion process parameters. This type of analysis at DUV wavelengths would enable the optimization of immersion lithography processes, thus enabling the qualification of immersion processes for volume production.
Identification of nickel-vacancy defects by combining experimental and ab initio simulated photocurrent spectra

Science.gov (United States)

Londero, E.; Bourgeois, E.; Nesladek, M.; Gali, A.

2018-06-01

There is a continuous search for solid state spin qubits operating at room temperature with excitation in the infrared communication bandwidth. Recently, we have introduced the photoelectric detection of magnetic resonance (PDMR) to read the electron spin state of nitrogen-vacancy (NV) centers in diamond, a technique which is promising for applications in quantum information technology. By measuring the photoionization spectra on a diamond crystal, we found two ionization thresholds of unknown origin. On the same sample we also observed absorption and photoluminescence signatures that were identified in the literature as Ni-associated defects. We performed ab initio calculations of the photoionization cross section of the nickel split-vacancy complex (NiV) and N-related defects in their relevant charge states and fitted the concentration of these defects to the measured photocurrent spectrum, which led to a surprising match between experimental and calculated spectra. This study enabled us to identify the two unknown ionization thresholds with the two acceptor levels of NiV. Because the excitation of NiV is in the infrared, the photocurrent detected from the paramagnetic NiV color centers is a promising way towards the design of electrically readout qubits.
Multi-spectrum and transmit-antenna switched diversity schemes for spectrum sharing systems: A performance analysis

KAUST Repository

Sayed, Mostafa

2012-12-01

In spectrum sharing systems, a secondary user (SU) is allowed to share the spectrum with a primary licensed user under the condition that the interference at the the primary user receiver (PU-Rx) is below a predetermined threshold. Joint primary spectrum and transmit antenna selection diversity schemes can be utilized as an efficient way to meet the quality of service (QoS) demands of the SUs while satisfying the interference constraint. In this paper, we consider a secondary link comprised of a secondary transmitter (SU-Tx) equipped with multiple antennas and a single-antenna secondary receiver (SU-Rx) sharing the same spectrum with a number of primary users (PUs) operating at distinct spectra. We present a performance analysis for two primary spectrum and transmit antenna switched selection schemes with different amount of feedback requirements. In particular, assuming Rayleigh fading and BPSK transmission, we derive approximate BER expressions for the presented schemes. For the sake of comparison, we also derive a closed-form BER expression for the optimal selection scheme that selects the best pair in terms of the SU-Rx signal-to-noise ratio (SNR) which has the disadvantage of high feedback requirements. Finally, our results are verified with numerical simulations. © 2012 IEEE.
Spectrum 101: An Introduction to Spectrum Management

Science.gov (United States)

2004-03-01

produces a Joint Restricted Frequency List (JRFL). The JFRL consolidates and classifies the spectrum uses that are most critical to operations and to...Management Office JRFL Joint Restricted Frequency List JSC Joint Spectrum Center JSIR Joint Spectrum Interference Resolution JSME Joint Spectrum...Multifunctional Information Distribution System MILSATCOM Military Satellite Communications MOA Memorandum of Agreement MRFL Master Radio Frequency
Defect production in ceramics

Energy Technology Data Exchange (ETDEWEB)

Zinkle, S.J. [Oak Ridge National Lab., TN (United States); Kinoshita, C. [Kyushu Univ. (Japan)

1997-08-01

A review is given of several important defect production and accumulation parameters for irradiated ceramics. Materials covered in this review include alumina, magnesia, spinel silicon carbide, silicon nitride, aluminum nitride and diamond. Whereas threshold displacement energies for many ceramics are known within a reasonable level of uncertainty (with notable exceptions being AIN and Si{sub 3}N{sub 4}), relatively little information exists on the equally important parameters of surviving defect fraction (defect production efficiency) and point defect migration energies for most ceramics. Very little fundamental displacement damage information is available for nitride ceramics. The role of subthreshold irradiation on defect migration and microstructural evolution is also briefly discussed.
Defects in dilute nitrides

International Nuclear Information System (INIS)

Chen, W.M.; Buyanova, I.A.; Tu, C.W.; Yonezu, H.

2005-01-01

We provide a brief review our recent results from optically detected magnetic resonance studies of grown-in non-radiative defects in dilute nitrides, i.e. Ga(In)NAs and Ga(Al,In)NP. Defect complexes involving intrinsic defects such as As Ga antisites and Ga i self interstitials were positively identified.Effects of growth conditions, chemical compositions and post-growth treatments on formation of the defects are closely examined. These grown-in defects are shown to play an important role in non-radiative carrier recombination and thus in degrading optical quality of the alloys, harmful to performance of potential optoelectronic and photonic devices based on these dilute nitrides. (author)
Genital and Urinary Tract Defects

Science.gov (United States)

... conditions > Genital and urinary tract defects Genital and urinary tract defects E-mail to a friend Please fill ... and extra fluids. What problems can genital and urinary tract defects cause? Genital and urinary tract defects affect ...
A REVIEW OF FACTORS AFFECTING BUILDING DEFECTS IN SINGAPORE

Directory of Open Access Journals (Sweden)

Po Seng Kian

2001-01-01

Full Text Available In developing countries, building maintenance technology is currently vastly underrated and ignored by owners, managers, and professionals. The building and construction authority of Singapore (BCA has identified that the complaints about building defects have gone up in recent years with common problems such as leaky roof and walls, floor defect, and improper outlet pipe. This paper presents a brief description on building defect in use for commercial building as well as residential buildings in Singapore. The main objective is to highlight the important problems and suggest a greater participation of professionals in building maintenance. It also provides some site investigations photographs of various defects, which is expected to be useful for builders, architects, and others who deal with building materials.
Market-driven spectrum sharing in cognitive radio

CERN Document Server

Yi, Changyan

2016-01-01

This brief focuses on the current research on mechanism design for dynamic spectrum sharing in cognitive radio (CR) networks. Along with a review of CR architectures and characteristics, this brief presents the motivations, significances and unique challenges of implementing algorithmic mechanism design for encouraging both primary spectrum owners and secondary spectrum users to participate in dynamic spectrum sharing. The brief then focuses on recent advances in mechanism design in CR networks. With an emphasis on dealing with the uncertain spectrum availabilities, mechanisms based on spectrum recall, two-stage spectrum sharing and online spectrum allocation are introduced with the support of theoretic analyses and numerical illustrations. The brief concludes with a discussion of potential research directions and interests, which will motivate further studies on mechanism design for wireless communications. This brief is concise and approachable for researchers, professionals and advanced-level students in w...

Investigation of a weld defect, reactor vessel head Ringhals 2

International Nuclear Information System (INIS)

Embring, G.; Pers-Anderson, E.B.

1994-01-01

During the summer-outage 1993 Ringhals unit 2 vessel head was inspected at weld-area of Alloy 182. One major defect was found Two plus two ''boat-samples'' were taken out from the zone between the weld and the stainless cladding. All samples were sent to Studsviks laboratories for detailed investigations. The metallographic and fractographic investigations revealed that the major weld-defect had been there from manufacturing. The defect was located between the Alloy 182-buttering and the pressure vessel steel SA 533 grB cl 1. No indications of PWSCC or IDSCC were found. An inspection programme was defined. Different types of reference blocks were provided by Ringhals in cooperation with ABB TRC. Reference reflectors of type flat bottom hole (FBH) and eroded notches (EDM), with different sizes and separation were manufactured. One weld sample with manufacturing defects -lack of fusion and slag was inclusions- was present. ABB TRC performed UT inspection in the gap between the penetration and the thermal sleeve. Inspection results like defect identification, defect separation and defect sizing accuracy were compared with result from the destructive inspection. No relevant additional defects were found. An analysing and repair program was performed. A special designed disc sealed off the defect area. (authors). 5 figs., 3 refs
Study on surface defects in milling Inconel 718 super alloy

Energy Technology Data Exchange (ETDEWEB)

Chang, Liu; Chengzu, Ren; Guofeng, Wang; Yinwei, Yang; Lu, Zhang [Tianjin University, Tianjin (China)

2015-04-15

Nickel-based alloys have been extensively used as critical components in aerospace industry, especially in the key section of aero engine. In general, these sections are manufactured by milling process because most of them have complex forms. However, surface defects appear frequently in milling due to periodic impact force, which leads to the deterioration of the fatigue life. We conducted milling experiments under different cutting conditions and found that four kinds of defects, i.e., tear, cavity, build up edge (BUE) and groove, commonly appear on the machined surface. Based on the observed results, the morphology and generation regime of these defects are analyzed and the carbide particle cracking is discussed to explain the appearance of the nickel alloy defects. To study the effect of the cutting parameters on the severity of these surface defects, two qualitative indicators, which are named as average number of the defects per field and average area ratio of the defects per field, are presented and the influence laws are summarized based on the results correspondingly. This study is helpful for understanding the generation mechanism of the surface defects during milling process of nickel based super alloy.
Digital detection system of surface defects for large aperture optical elements

International Nuclear Information System (INIS)

Fan Yong; Chen Niannian; Gao Lingling; Jia Yuan; Wang Junbo; Cheng Xiaofeng

2009-01-01

Based on the light defect images against the dark background in a scattering imaging system, a digital detection system of surface defects for large aperture optical elements has been presented. In the system, the image is segmented by a multi-area self-adaptive threshold segmentation method, then a pixel labeling method based on replacing arrays is adopted to extract defect features quickly, and at last the defects are classified through back-propagation neural networks. Experiment results show that the system can achieve real-time detection and classification. (authors)
Characterization of point defects in CdTe by positron annihilation spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Elsharkawy, M. R. M. [Carnegie Laboratory of Physics, SUPA, School of Science and Engineering, University of Dundee, Dundee DD1 4HN (United Kingdom); Physics Department, Faculty of Science, Minia University, P.O. Box 61519, Minia (Egypt); Kanda, G. S.; Keeble, D. J., E-mail: d.j.keeble@dundee.ac.uk [Carnegie Laboratory of Physics, SUPA, School of Science and Engineering, University of Dundee, Dundee DD1 4HN (United Kingdom); Abdel-Hady, E. E. [Physics Department, Faculty of Science, Minia University, P.O. Box 61519, Minia (Egypt)

2016-06-13

Positron lifetime measurements on CdTe 0.15% Zn-doped by weight are presented, trapping to monovacancy defects is observed. At low temperatures, localization at shallow binding energy positron traps dominates. To aid defect identification density functional theory, calculated positron lifetimes and momentum distributions are obtained using relaxed geometry configurations of the monovacancy defects and the Te antisite. These calculations provide evidence that combined positron lifetime and coincidence Doppler spectroscopy measurements have the capability to identify neutral or negative charge states of the monovacancies, the Te antisite, A-centers, and divacancy defects in CdTe.
Defect mediated optical properties in ZnAl2O4 phosphor

Science.gov (United States)

Pathak, Nimai; Saxena, Suryansh; Kadam, R. M.

2018-04-01

The present work describes defect mediated optical properties in ZnAl2O4 phosphor material, synthesized through sol-gel combustion method, which has potential to be used both as a blue emitting phosphor material as well as white emitting, depending upon the annealing temperature during the synthesis procedure. Various defect centers such as anionic vacancy, cationic vacancy, antisite defects etc. create different electronic states inside the band gap, which are responsible for the multicolour emission. The interesting colour tunable emission characteristics can be linked with the various defect centers and their changes upon annealing.
Surface-defect induced modifications in the optical properties of α-MnO_2 nanorods

International Nuclear Information System (INIS)

John, Reenu Elizabeth; Chandran, Anoop; Thomas, Marykutty; Jose, Joshy; George, K.C.

2016-01-01

Graphical abstract: - Highlights: • Alpha-MnO_2 nanorods are prepared by chemical method. • Difference in surface defect density is achieved. • Characterized using XRD, Rietveld, XPS, EDS, HR-TEM, BET, UV–vis absorption spectroscopy and PL spectroscopy. • Explains the bandstructure modification due to Jahn–Teller distortions using crystal field theory. • Modification in the intensity of optical emissions related to defect levels validates the concept of surface defect induced tuning of optical properties. - Abstract: The science of defect engineering via surface tuning opens a new route to modify the inherent properties of nanomaterials for advanced functional and practical applications. In this work, two independent synthesis methods (hydrothermal and co-precipitation) are adopted to fabricate α-MnO_2 nanorods with different defect structures so as to understand the effect of surface modifications on their optical properties. The crystal structure and morphology of samples are investigated with the aid of X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Atomic composition calculated from energy dispersive spectroscopy (EDS) confirms non-stoichiometry of the samples. The surface properties and chemical environment are thoroughly studied using X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) analysis. Bond angle variance and bond valence sum are determined to validate distortions in the basic MnO_6 octahedron. The surface studies indicate that the concentration of Jahn–Teller manganese (III) (Mn"3"+) ion in the samples differ from each other which results in their distinct properties. Band structure modifications due to Jahn–Teller distortion are examined with the aid of ultraviolet–visible (UV) reflectance and photoluminescence (PL) studies. The dual peaks obtained in derivative spectrum conflict the current concept on the bandgap energy of MnO_2. These studies suggest that
Covering the Dorsal Finger Defect with Reverse Cross Finger Flap

Directory of Open Access Journals (Sweden)

Kaan Gurbuz

2014-12-01

Full Text Available Reconstruction of finger extensor zone defects with or without tendon gaps still remains a challenge for surgeons. Although surgical treatments may differ, and range from the use of local, regional, to free flaps, the outcomes for all cases are not satisfactory. In this case report, we present a case of a 3rd finger extensor side crush injury including a defect of Dd (Digit Dorsal 1, Dd2 and Dd3 defects of extensor zones with tendon gap. Tendon gap was reconstructed using m. palmaris longus tendon graft and the defect was covered with reversed cross-finger flap (random pattern with good cosmetic and excellent functional results.
Topological defect clustering and plastic deformation mechanisms in functionalized graphene

Science.gov (United States)

Nunes, Ricardo; Araujo, Joice; Chacham, Helio

2011-03-01

We present ab initio results suggesting that strain plays a central role in the clustering of topological defects in strained and functionalized graphene models. We apply strain onto the topological-defect graphene networks from our previous work, and obtain topological-defect clustering patterns which are in excellent agreement with recent observations in samples of reduced graphene oxide. In our models, the graphene layer, containing an initial concentration of isolated topological defects, is covered by hydrogen or hydroxyl groups. Our results also suggest a rich variety of plastic deformation mechanism in functionalized graphene systems. We acknowledge support from the Brazilian agencies: CNPq, Fapemig, and INCT-Materiais de Carbono.
Neural Tube Defects: Epidemiologic Factors, Clinical Presentation ...

African Journals Online (AJOL)

Of the 103 babies, 87 (84.5%) had spina bifida cystica, 15 (14.6%) had occipital encephalocele, while 1 (0.9%) had anencephaly and died within 8 hours of delivery. All the 87 patients with spina bifida cystica were ruptured and infected at presentation, with seven of them dying from overwhelming sepsis. Most of the babies ...
Incomplete bone regeneration of rabbit calvarial defects using different membranes

DEFF Research Database (Denmark)

Aaboe, M; Pinholt, E M; Schou, S

1998-01-01

The present study describes the use of a degradable and a non-degradable material for guided bone regeneration. Forty rabbits were divided into 5 groups. Bicortical defects 15 mm in diameter were prepared in rabbit calvaria. A titanium microplate was placed over the defect to prevent collapse...
Point defects and defect clusters examined on the basis of some fundamental experiments

International Nuclear Information System (INIS)

Zuppiroli, L.

1975-01-01

On progressing from the centre of the defect to the surface the theoretical approach to a point defect passes from electronic theories to elastic theory. Experiments by which the point defect can be observed fall into two categories. Those which detect long-range effects: measurement of dimensional variations in the sample; measurement of the mean crystal parameter variation; elastic X-ray scattering near the nodes of the reciprocal lattice (Huang scattering). Those which detect more local effects: low-temperature resistivity measurement; positron capture and annihilation; local scattering far from the reciprocal lattice nodes. Experiments involving both short and long-range effects can always be found. This is the case for example with the dechanneling of α particles by defects. Certain of the experimental methods quoted above apply also to the study of point defect clusters. These methods are illustrated by some of their most striking results which over the last twenty years have refined our knowledge of point defects and defect clusters: length and crystal parameter measurements; diffuse X-ray scattering; low-temperature resistivity measurements; ion emission microscopy; electron microscopy; elastoresistivity [fr
Birth Defects (For Parents)

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Birth Defects KidsHealth / For Parents / Birth Defects What's in ... Prevented? Print en español Anomalías congénitas What Are Birth Defects? While still in the womb, some babies ...
Spectrally resolved thermally stimulated luminescence of irradiated anion-defective alumina single crystals

Energy Technology Data Exchange (ETDEWEB)

Kortov, V., E-mail: vskortov@mail.ru [Ural Federal University, Mira Str. 19, 620002 Ekaterinburg (Russian Federation); Lushchik, A.; Nagirnyi, V. [Institute of Physics, University of Tartu, W. Ostwald Str. 1, 50411 Tartu (Estonia); Ananchenko, D. [Ural Federal University, Mira Str. 19, 620002 Ekaterinburg (Russian Federation); Romet, I. [Institute of Physics, University of Tartu, W. Ostwald Str. 1, 50411 Tartu (Estonia)

2017-06-15

Thermally stimulated luminescence (TSL) spectra in the 313–580 K temperature range have been studied in anion-defective alumina crystals (named in literature as Al{sub 2}O{sub 3}:C) exposed to different irradiation doses. The TSL curve features two peaks with the maxima at T{sub m1}=437 K and T{sub m2}=565 K. The TSL spectrum of the first peak contains the emission of F centers and the R line of Cr{sup 3+} impurity ions. The absence of the emission of F{sup +} centers indicates that electron traps are responsible for the first dosimetric TSL peak. The TSL spectrum of the second peak features emission bands of F, F{sup +} centers, R line as well as a wide band centered at 550 nm and associated with the formation of aggregate centers (F{sub 2} and F{sub 2}{sup 2+}) under irradiation. Possible excitation mechanisms of the TSL emission bands that involve both electron and hole traps related to anion vacancies and impurities are discussed. - Highlights: •TSL curve of alumina crystals features peaks at 437 and 565 K. •There are emission bands of 410 and 695 nm in the TSL spectrum of the first peak. •TSL spectrum of the second peak features bands of F, F{sub 2}-type centers and the R line of trivalent chromium. •Excitation mechanisms of the emission bands in TSL spectra are discussed.
Characterisation of irradiation-induced defects in ZnO single crystals

International Nuclear Information System (INIS)

Prochazka, I; Cizek, J; Lukac, F; Melikhova, O; Valenta, J; Havranek, V; Anwand, W; Skuratov, V A; Strukova, T S

2016-01-01

Positron annihilation spectroscopy (PAS) combined with optical methods was employed for characterisation of defects in the hydrothermally grown ZnO single crystals irradiated by 167 MeV Xe 26+ ions to fluences ranged from 3×10 12 to 1×10 14 cm -2 . The positron lifetime (LT), Doppler broadening as well as slow-positron implantation spectroscopy (SPIS) techniques were involved. The ab-initio theoretical calculations were utilised for interpretation of LT results. The optical transmission and photoluminescence measurements were conducted, too. The virgin ZnO crystal exhibited a single component LT spectrum with a lifetime of 182 ps which is attributed to saturated positron trapping in Zn vacancies associated with hydrogen atoms unintentionally introduced into the crystal during the crystal growth. The Xe ion irradiated ZnO crystals have shown an additional component with a longer lifetime of ≈ 360 ps which comes from irradiation-induced larger defects equivalent in size to clusters of ≈10 to 12 vacancies. The concentrations of these clusters were estimated on the basis of combined LT and SPIS data. The PAS data were correlated with irradiation induced changes seen in the optical spectroscopy experiments. (paper)
Characterisation of irradiation-induced defects in ZnO single crystals

Science.gov (United States)

Prochazka, I.; Cizek, J.; Lukac, F.; Melikhova, O.; Valenta, J.; Havranek, V.; Anwand, W.; Skuratov, V. A.; Strukova, T. S.

2016-01-01

Positron annihilation spectroscopy (PAS) combined with optical methods was employed for characterisation of defects in the hydrothermally grown ZnO single crystals irradiated by 167 MeV Xe26+ ions to fluences ranged from 3×1012 to 1×1014 cm-2. The positron lifetime (LT), Doppler broadening as well as slow-positron implantation spectroscopy (SPIS) techniques were involved. The ab-initio theoretical calculations were utilised for interpretation of LT results. The optical transmission and photoluminescence measurements were conducted, too. The virgin ZnO crystal exhibited a single component LT spectrum with a lifetime of 182 ps which is attributed to saturated positron trapping in Zn vacancies associated with hydrogen atoms unintentionally introduced into the crystal during the crystal growth. The Xe ion irradiated ZnO crystals have shown an additional component with a longer lifetime of ≈ 360 ps which comes from irradiation-induced larger defects equivalent in size to clusters of ≈10 to 12 vacancies. The concentrations of these clusters were estimated on the basis of combined LT and SPIS data. The PAS data were correlated with irradiation induced changes seen in the optical spectroscopy experiments.
Defect correction and multigrid for an efficient and accurate computation of airfoil flows

NARCIS (Netherlands)

Koren, B.

1988-01-01

Results are presented for an efficient solution method for second-order accurate discretizations of the 2D steady Euler equations. The solution method is based on iterative defect correction. Several schemes are considered for the computation of the second-order defect. In each defect correction
Radiation defects in electron-irradiated InP crystals

International Nuclear Information System (INIS)

Brailovskii, E.Yu.; Karapetyan, F.K.; Megela, I.G.; Tartachnik, V.P.

1982-01-01

The results are presented of formation and annealing of defects in InP crystals at 1 to 50 MeV electron irradiation. The recovery of electrical properties in the range of 77 to 970 K during annealing processes is studied. Five low temperature annealing states in n-InP and the reverse annealing in p-InP are observed at 77 to 300 K. Four annealing stages at temperatures higher than 300 K are present. When the electron energy is increased more complicated thermostable defects are formed, and at 50 MeV electron energy besides of the point defect clusters are formed, which anneal at temperatures of 800 to 970 K. It is shown that the peculiarities of the Hall mobility at irradiation and annealing are caused by the scattering centres E/sub c/ - 0.2 eV. The 'limiting' position of the Fermi level in electron irradiated InP crystals is discussed. (author)
Radiation defects in electron-irradiated InP crystals

Energy Technology Data Exchange (ETDEWEB)

Brailovskii, E.Yu.; Karapetyan, F.K.; Megela, I.G.; Tartachnik, V.P. (AN Ukrainskoj SSR, Kiev. Inst. Yadernykh Issledovanij)

1982-06-16

The results are presented of formation and annealing of defects in InP crystals at 1 to 50 MeV electron irradiation. The recovery of electrical properties in the range of 77 to 970 K during annealing processes is studied. Five low temperature annealing states in n-InP and the reverse annealing in p-InP are observed at 77 to 300 K. Four annealing stages at temperatures higher than 300 K are present. When the electron energy is increased more complicated thermostable defects are formed, and at 50 MeV electron energy besides of the point defect clusters are formed, which anneal at temperatures of 800 to 970 K. It is shown that the peculiarities of the Hall mobility at irradiation and annealing are caused by the scattering centres E/sub c/ - 0.2 eV. The 'limiting' position of the Fermi level in electron irradiated InP crystals is discussed.
Lithium niobate. Defects, photorefraction and ferroelectric switching

Energy Technology Data Exchange (ETDEWEB)

Volk, Tatyana [Russian Academy of Sciences, Inst. for Crystallography, Moscow (Russian Federation); Woehlecke, Manfred [Osnabrueck Univ. (Germany). Fachbereich Physik

2008-07-01

The book presents the current state of studies of point defects, both intrinsic and extrinsic (impurities, radiation centers, etc.), in LiNbO{sub 3}. The contribution of intrinsic defects to photoinduced charge transport, i.e. to the photorefraction, is explained. The photorefractive and optical properties of LiNbO{sub 3} crystals with different stoichiometry and of those doped with so-called ''optical-damage resistant'' impurities controlling the intrinsic defect structure are described in detail. Applications included are to the problem of non-erasable recording of photorefractive holograms in LiNbO{sub 3} and the current situation of studies in the ferroelectric switching and domain structure of LiNbO{sub 3}, as well as the creation of periodically-poled structures for the optical frequency conversion. (orig.)
Congenital anomalies of the pulmonary arteries: spectrum of findings on computed tomography.

Science.gov (United States)

Bueno, J; Flors, L; Mejía, M

Congenital anomalies of the pulmonary arteries are uncommon. They can occur in isolation or in association with congenital heart defects. Isolated congenital anomalies remain undiscovered until they are reported as incidental findings on imaging tests, usually not until adolescence. We review the embryological development and normal anatomy of the pulmonary arteries as well as the spectrum of computed tomography findings for various congenital anomalies: unilateral interruption of the pulmonary artery, anomalous origin of the left pulmonary artery (pulmonary artery sling), idiopathic aneurysm of the pulmonary artery, and other anomalies associated with congenital heart defects. Congenital anomalies of the pulmonary arteries represent a diagnostic challenge for clinicians and radiologists. Computed tomography is useful for their diagnosis, and general radiologists need to be familiar with their imaging appearance because they are often discovered incidentally. Copyright © 2016 SERAM. Publicado por Elsevier España, S.L.U. All rights reserved.

Spectrum

DEFF Research Database (Denmark)

Høgfeldt Hansen, Leif

2016-01-01

The publication functions as a proces description of the development and construction of an urban furniture SPECTRUM in the city of Gwangju, Republic of Korea. It is used as the cataloque for the exhibition of Spectrum.......The publication functions as a proces description of the development and construction of an urban furniture SPECTRUM in the city of Gwangju, Republic of Korea. It is used as the cataloque for the exhibition of Spectrum....
Formation of topological defects

International Nuclear Information System (INIS)

Vachaspati, T.

1991-01-01

We consider the formation of point and line topological defects (monopoles and strings) from a general point of view by allowing the probability of formation of a defect to vary. To investigate the statistical properties of the defects at formation we give qualitative arguments that are independent of any particular model in which such defects occur. These arguments are substantiated by numerical results in the case of strings and for monopoles in two dimensions. We find that the network of strings at formation undergoes a transition at a certain critical density below which there are no infinite strings and the closed-string (loop) distribution is exponentially suppressed at large lengths. The results are contrasted with the results of statistical arguments applied to a box of strings in dynamical equilibrium. We argue that if point defects were to form with smaller probability, the distance between monopoles and antimonopoles would decrease while the monopole-to-monopole distance would increase. We find that monopoles are always paired with antimonopoles but the pairing becomes clean only when the number density of defects is small. A similar reasoning would also apply to other defects
Photographic guide of selected external defect indicators and associated internal defects in sugar maple

Science.gov (United States)

Everette D. Rast; John A. Beaton; David L. Sonderman

1991-01-01

To properly classify or grade logs or trees, one must be able to correctly identify defect indicators and assess the effect of the underlying defect on possible end products. This guide assists the individual in identifying the surface defect indicator and shows the progressive stages of the defect throughout its development for sugar maple. Eleven types of external...
Photographic guide of selected external defect indicators and associated internal defects in yellow-poplar

Science.gov (United States)

Everette D. Rast; John A. Beaton; David L. Sonderman

1991-01-01

To properly classify or grade logs or trees, one must be able to correctly identify defect indicators and assess the effect of the underlying defect on possible end products. This guide assists the individual in identifying the surface defect indicator and shows the progressive stages of the defect throughout its development for yellow-poplar. Twelve types of external...
Photographic guide of selected external defect indicators and associated internal defects in yellow birch

Science.gov (United States)

Everette D. Rast; John A. Beaton; David L. Sonderman

1991-01-01

To properly classify or grade logs or trees, one must be able to correctly identify defect indicators and assess the effect of the underlying defect on possible end products. This guide assists the individual in identifying the surface defect indicator and shows the progressive stages of the defect throughout its development for yellow birch. Eleven types of external...
Gerbode defect following endocarditis and misinterpreted as severe pulmonary arterial hypertension

Directory of Open Access Journals (Sweden)

Allajbeu Iris

2010-09-01

Full Text Available Abstract A Gerbode -type defect is a ventricular septal defect communicating directly between the left ventricle and right atrium. It is usually congenital, but rarely is acquired, as a complication of endocarditis. This can be anatomically possible because the normal tricuspid valve is more apically displaced than the mitral valve. However, identification of an actual communication is often extremely difficult, so a careful and meticulous echocardiogram should be done in order to prevent echocardiographic misinterpretation of this defect as pulmonary arterial hypertension. The large systolic pressure gradient between the left ventricle and the right atrium would expectedly result in a high velocity systolic Doppler flow signal in right atrium and it can be sometimes mistakably diagnosed as tricuspid regurgitant jet simulating pulmonary arterial hypertension. We present a rare case of young woman, with endocarditis who presented with severe pulmonary arterial hypertension. The preoperative diagnosis of left ventricle to right atrial communication (acquired Gerbode defect was suspected initially by echocardiogram and confirmed at the time of the surgery. A point of interest, apart from the diagnostic problem, was the explanation for its mechanism and presentation. The probability of a bacterial etiology of the defect is high in this case.
Surface Casting Defects Inspection Using Vision System and Neural Network Techniques

Directory of Open Access Journals (Sweden)

Świłło S.J.

2013-12-01

Full Text Available The paper presents a vision based approach and neural network techniques in surface defects inspection and categorization. Depending on part design and processing techniques, castings may develop surface discontinuities such as cracks and pores that greatly influence the material’s properties Since the human visual inspection for the surface is slow and expensive, a computer vision system is an alternative solution for the online inspection. The authors present the developed vision system uses an advanced image processing algorithm based on modified Laplacian of Gaussian edge detection method and advanced lighting system. The defect inspection algorithm consists of several parameters that allow the user to specify the sensitivity level at which he can accept the defects in the casting. In addition to the developed image processing algorithm and vision system apparatus, an advanced learning process has been developed, based on neural network techniques. Finally, as an example three groups of defects were investigated demonstrates automatic selection and categorization of the measured defects, such as blowholes, shrinkage porosity and shrinkage cavity.
A study of complex defects failing by fatigue, ductile tearing and cleavage

International Nuclear Information System (INIS)

Bezensek, B.; Ren, Z.; Hancock, J.W.

2001-01-01

Defect assessment procedures ensure the structural integrity of plant, which may contain complex defects. The present work addresses complex defects with re-entrant sectors, which develop from the interaction of two co-planar surface breaking defects in fatigue. Experimental studies show rapid fatigue growth and amplified crack driving forces in the re-entrant sector. This leads to the rapid evolution of the complex crack into a bounding semielliptical defect. Experiments involving ductile tearing of cracks with a re-entrant sector show that tearing initiates in the re-entrant sector and that the defect evolves into a bounding semielliptical defect. Cleavage failures of defects with re-entrant sectors indicate the re-characterisation procedure is only conservative after invoking constraint arguments. The study confirms the conservatism inherent in the re-characterisation rules of assessment procedures, such as BS 7910 [1] and ASME Section XI [2] for complex defects extending by fatigue or ductile tearing. A potentially non-conservative situation exists for defects with re-entrant sectors failing by cleavage at small fractions of the limit load.(author)
Entanglement entropy in integrable field theories with line defects II. Non-topological defect

Science.gov (United States)

Jiang, Yunfeng

2017-08-01

This is the second part of two papers where we study the effect of integrable line defects on bipartite entanglement entropy in integrable field theories. In this paper, we consider non-topological line defects in Ising field theory. We derive an infinite series expression for the entanglement entropy and show that both the UV and IR limits of the bulk entanglement entropy are modified by the line defect. In the UV limit, we give an infinite series expression for the coefficient in front of the logarithmic divergence and the exact defect g-function. By tuning the defect to be purely transmissive and reflective, we recover correctly the entanglement entropy of the bulk and with integrable boundary respectively.
Frequency of brain MRI abnormalities in neuromyelitis optica spectrum disorder at presentation: A cohort of Latin American patients.

Science.gov (United States)

Carnero Contentti, Edgar; Daccach Marques, Vanessa; Soto de Castillo, Ibis; Tkachuk, Veronica; Antunes Barreira, Amilton; Armas, Elizabeth; Chiganer, Edson; de Aquino Cruz, Camila; Di Pace, José Luis; Hryb, Javier Pablo; Lavigne Moreira, Carolina; Lessa, Carmen; Molina, Omaira; Perassolo, Monica; Soto, Arnoldo; Caride, Alejandro

2018-01-01

Brain magnetic resonance imaging (BMRI) lesions were classically not reported in neuromyelitis optica (NMO). However, BMRI lesions are not uncommon in NMO spectrum disorder (NMOSD) patients. To report BMRI characteristic abnormalities (location and configuration) in NMOSD patients at presentation. Medical records and BMRI characteristics of 79 patients with NMOSD (during the first documented attack) in Argentina, Brazil and Venezuela were reviewed retrospectively. BMRI abnormalities were observed in 81.02% of NMOSD patients at presentation. Forty-two patients (53.1%) showed typical-NMOSD abnormalities. We found BMRI abnormalities at presentation in the brainstem/cerebellum (n = 26; 32.9%), optic chiasm (n = 16; 20.2%), area postrema (n = 13; 16.4%), thalamus/hypothalamus (n = 11; 13.9%), corpus callosum (n = 11; 13.9%), periependymal-third ventricle (n = 9; 11.3%), corticospinal tract (n = 7; 8.8%), hemispheric white matter (n = 1; 1.2%) and nonspecific areas (n = 49; 62.03%). Asymptomatic BMRI lesions were more common. The frequency of brain MRI abnormalities did not differ between patients who were positive and negative for aquaporin 4 antibodies at presentation. Typical brain MRI abnormalities are frequent in NMOSD at disease onset. Copyright © 2017 Elsevier B.V. All rights reserved.
First-principles engineering of charged defects for two-dimensional quantum technologies

Science.gov (United States)

Wu, Feng; Galatas, Andrew; Sundararaman, Ravishankar; Rocca, Dario; Ping, Yuan

2017-12-01

Charged defects in two-dimensional (2D) materials have emerging applications in quantum technologies such as quantum emitters and quantum computation. The advancement of these technologies requires a rational design of ideal defect centers, demanding reliable computation methods for the quantitatively accurate prediction of defect properties. We present an accurate, parameter-free, and efficient procedure to evaluate the quasiparticle defect states and thermodynamic charge transition levels of defects in 2D materials. Importantly, we solve critical issues that stem from the strongly anisotropic screening in 2D materials, that have so far precluded the accurate prediction of charge transition levels in these materials. Using this procedure, we investigate various defects in monolayer hexagonal boron nitride (h -BN ) for their charge transition levels, stable spin states, and optical excitations. We identify CBVN (nitrogen vacancy adjacent to carbon substitution of boron) to be the most promising defect candidate for scalable quantum bit and emitter applications.
Ventricular septal defect closure in a patient with achondroplasia.

Science.gov (United States)

Nakanishi, Keisuke; Kawasaki, Shiori; Amano, Atsushi

2017-01-01

Achondroplasia with co-morbid CHD is rare, as are reports of surgical treatment for such patients. We present the case of a 13-year-old girl with achondroplasia and ventricular septal defect. Her ventricular septal defect was surgically repaired focussing on the cardiopulmonary bypass flow, healing of the sternum, and her frail neck cartilage. The surgery and recovery were without complications.
The Role of Co-Occurring Disruptive Behavior in the Clinical Presentation of Children and Adolescents with Anxiety in the Context of Autism Spectrum Disorders

Science.gov (United States)

Storch, Eric A.; Arnold, Elysse B.; Jones, Anna M.; Ale, Chelsea M.; Wood, Jeffrey J.; Ehrenreich-May, Jill; Lewin, Adam B.; Mutch, P. Jane; Murphy, Tanya K.

2012-01-01

This study explored the impact of disruptive behavior disorder (DBD) comorbidity on theoretically relevant correlates among 87 children and adolescents with autism spectrum disorders (ASD) and clinically significant anxiety. Relative to youth with ASD and anxiety alone, participants with ASD, anxiety, and DBD: (a) presented with significantly more…
Defect-based testing of LTS digital circuits

NARCIS (Netherlands)

Arun, A.J.

2006-01-01

A Defect-Based Test (DBT) methodology for Superconductor Electronics (SCE) is presented in this thesis, so that commercial production and efficient testing of systems can be implemented in this technology in the future. In the first chapter, the features and prospects for SCE have been presented.
Defects related room temperature ferromagnetism in Cu-implanted ZnO nanorod arrays

International Nuclear Information System (INIS)

Li, D.; Li, D.K.; Wu, H.Z.; Liang, F.; Xie, W.; Zou, C.W.; Shao, L.X.

2014-01-01

Highlights: • Room temperature ferromagnetism was observed in Cu-implanted ZnO nanorod arrays. • Cu-implanted ZnO nanorods show a saturation magnetization value of 1.82 μ B /Cu. • The origin of ferromagnetism can be explained by the defects related bound magnetic polarons. -- Abstract: Room temperature ferromagnetism (FM) was observed in Cu-implanted ZnO nanorod arrays. The implantation dose for Cu ions was 1 × 10 16 cm −2 and the implantation energy was 100 keV. The ion implantation induced defects and disorder has been observed by the XRD, PL and TEM experiments. The PL spectrum revealed a dominant luminescence peaks at 390 nm and a broad and strong green emission at 500–700 nm, which is considered to be related to the ionized oxygen vacancy. Cu-implanted ZnO nanorods annealed at 500 °C show a saturation magnetization value of 1.82 μ B /Cu and a positive coercive field of 68 Oe. The carrier concentration is not much improved after annealing and in the order of 10 16 cm −3 , which suggests that FM does not depend upon the presence of a significant carrier concentration. The origin of ferromagnetism behavior can be explained on the basis of electrons and defects that form bound magnetic polarons, which overlap to create a spin-split impurity band
Deep sub-wavelength metrology for advanced defect classification

Science.gov (United States)

van der Walle, P.; Kramer, E.; van der Donck, J. C. J.; Mulckhuyse, W.; Nijsten, L.; Bernal Arango, F. A.; de Jong, A.; van Zeijl, E.; Spruit, H. E. T.; van den Berg, J. H.; Nanda, G.; van Langen-Suurling, A. K.; Alkemade, P. F. A.; Pereira, S. F.; Maas, D. J.

2017-06-01

Particle defects are important contributors to yield loss in semi-conductor manufacturing. Particles need to be detected and characterized in order to determine and eliminate their root cause. We have conceived a process flow for advanced defect classification (ADC) that distinguishes three consecutive steps; detection, review and classification. For defect detection, TNO has developed the Rapid Nano (RN3) particle scanner, which illuminates the sample from nine azimuth angles. The RN3 is capable of detecting 42 nm Latex Sphere Equivalent (LSE) particles on XXX-flat Silicon wafers. For each sample, the lower detection limit (LDL) can be verified by an analysis of the speckle signal, which originates from the surface roughness of the substrate. In detection-mode (RN3.1), the signal from all illumination angles is added. In review-mode (RN3.9), the signals from all nine arms are recorded individually and analyzed in order to retrieve additional information on the shape and size of deep sub-wavelength defects. This paper presents experimental and modelling results on the extraction of shape information from the RN3.9 multi-azimuth signal such as aspect ratio, skewness, and orientation of test defects. Both modeling and experimental work confirm that the RN3.9 signal contains detailed defect shape information. After review by RN3.9, defects are coarsely classified, yielding a purified Defect-of-Interest (DoI) list for further analysis on slower metrology tools, such as SEM, AFM or HIM, that provide more detailed review data and further classification. Purifying the DoI list via optical metrology with RN3.9 will make inspection time on slower review tools more efficient.
Natural defects and defects created by ionic implantation in zinc tellurium

International Nuclear Information System (INIS)

Roche, J.P.; Dupuy, M.; Pfister, J.C.

1977-01-01

Various defects have been studied in ZnTe crystals by transmission electron microscope and by scanning electron microscope in cathodo-luminescence mode: grain boundaries, sub-grain boundaries, twins. Ionic implants of boron (100 keV - 2x10 14 and 10 15 ions cm -2 ) were made on these crystals followed by isochrone annealing (30 minutes) of zinc under partial pressure at 550, 650 and 750 0 C. The nature of the defects was determined by transmission electron microscope: these are interstitial loops (b=1/3 ) the size of which varies between 20 A (non-annealed sample) and 180A (annealed at 750 0 C). The transmission electron microscope was also used to make concentration profiles of defects depending on depth. It is found that for the same implant (2x10 14 ions.cm -2 ), the defect peak moves towards the exterior of the crystal as the annealing temperature rises (400 - 1000 and 7000 A for the three annealings). These results are explained from a model which allows for the coalescence of defects and considers the surface of the sample as being the principal source of vacancies. During the annealings, the migration of vacancies brings about the gradual annihilation of the implant defects. The adjustment of certain calculation parameters on the computer result in giving 2 eV as energy value for the formation of vacancies [fr
Early diagnosis of autism spectrum disorder: stability and change in clinical diagnosis and symptom presentation.

Science.gov (United States)

Guthrie, Whitney; Swineford, Lauren B; Nottke, Charly; Wetherby, Amy M

2013-05-01

Although a diagnosis of autism spectrum disorder (ASD) appears to be stable in children as young as age three, few studies have explored stability of a diagnosis in younger children. Predictive value of diagnostic tools for toddlers and patterns of symptom change are important considerations for clinicians making early diagnoses. Most findings come from high-risk samples, but reports on children screened in community settings are also needed. Stability of diagnosis and Autism Diagnostic Observation Schedule – Toddler Module (ADOS-T) classifications and scores was examined across two time points in a sample of 82 children identified through the FIRST WORDS Project.Children received two comprehensive diagnostic evaluations at average ages of 19.39 (SD = 2.12) and 36.89 (SD = 3.85) months. Stability was 100% when confirming and ruling out a diagnosis of ASD based on a comprehensive diagnostic evaluation that included clinic and home observations,although diagnosis was initially deferred for 17% of the sample. Receiver Operating Characteristic curves revealed excellent sensitivity and acceptable specificity for the ADOS-T compared to concurrent diagnosis. Logistic regressions indicated good predictive value of initial ADOS-T scores for follow-up diagnosis. Finally, both ASD and Non-ASD children demonstrated a decrease in Social Affect scores (i.e.,improvement), whereas children with ASD demonstrated an increase in Restricted and Repetitive Behavior scores (i.e., worsening), changes that were accounted for by nonverbal developmental level in mixed model analyses. Short-term stability was documented for children diagnosed at 19 months on average, although a minority of children initially showed unclear diagnostic presentations.Findings highlight utility of the ADOS-T in making early diagnoses and predicting follow-up diagnoses. Children with ASD demonstrated improvement in social communication behaviors and unfolding of repetitive behaviors, suggesting that certain
Modeling the relationships among internal defect features and external Appalachian hardwood log defect indicators

Science.gov (United States)

R. Edward. Thomas

2009-01-01

As a hardwood tree grows and develops, surface defects such as branch stubs and wounds are overgrown. Evidence of these defects remain on the log surface for decades and in many instances for the life of the tree. As the tree grows the defect is encapsulated or grown over by new wood. During this process the appearance of the defect in the tree's bark changes. The...
Novel mutation of GATA4 gene in Kurdish population of Iran with nonsyndromic congenital heart septals defects.

Science.gov (United States)

Soheili, Fariborz; Jalili, Zahra; Rahbar, Mahtab; Khatooni, Zahed; Mashayekhi, Amir; Jafari, Hossein

2018-03-01

The mutations in GATA4 gene induce inherited atrial and ventricular septation defects, which is the most frequent forms of congenital heart defects (CHDs) constituting about half of all cases. We have performed High resolution melting (HRM) mutation scanning of GATA4 coding exons of nonsyndrome 100 patients as a case group including 39 atrial septal defects (ASD), 57 ventricular septal defects (VSD) and four patients with both above defects and 50 healthy individuals as a control group. Our samples are categorized according to their HRM graph. The genome sequencing has been done for 15 control samples and 25 samples of patients whose HRM analysis were similar to healthy subjects for each exon. The PolyPhen-2 and MUpro have been used to determine the causative possibility and structural stability prediction of GATA4 sequence variation. The HRM curve analysis exhibit that 21 patients and 3 normal samples have deviated curves for GATA4 coding exons. Sequencing analysis has revealed 12 nonsynonymous mutations while all of them resulted in stability structure of protein 10 of them are pathogenic and 2 of them are benign. Also we found two nucleotide deletions which one of them was novel and one new indel mutation resulting in frame shift mutation, and 4 synonymous variations or polymorphism in 6 of patients and 3 of normal individuals. Six or about 50% of these nonsynonymous mutations have not been previously reported. Our results show that there is a spectrum of GATA4 mutations resulting in septal defects. © 2018 Wiley Periodicals, Inc.

Visual detection of defects in solder joints

Science.gov (United States)

Blaignan, V. B.; Bourbakis, Nikolaos G.; Moghaddamzadeh, Ali; Yfantis, Evangelos A.

1995-03-01

The automatic, real-time visual acquisition and inspection of VLSI boards requires the use of machine vision and artificial intelligence methodologies in a new `frame' for the achievement of better results regarding efficiency, products quality and automated service. In this paper the visual detection and classification of different types of defects on solder joints in PC boards is presented by combining several image processing methods, such as smoothing, segmentation, edge detection, contour extraction and shape analysis. The results of this paper are based on simulated solder defects and a real one.
International conference on defects in insulating crystals

International Nuclear Information System (INIS)

1977-01-01

Short summaries of conference papers are presented. Some of the conference topics included transport properties, defect levels, superionic conductors, radiation effects, John-Teller effect, electron-lattice interactions, and relaxed excited states
The effect of defect types on the electronic and optical properties of graphene nanoflakes physisorbed by ionic liquids.

Science.gov (United States)

Shakourian-Fard, Mehdi; Kamath, Ganesh

2017-02-08

Defect engineering and non-covalent interaction strategies allow for dramatically tuning the optoelectronic properties of graphene. Using ab initio density functional theory (M06-2X/cc-pVDZ), we find that the nature of defects on the graphene nanoflakes (GNFs) and the size of defective GNF (DGNF) surfaces affect the binding energy (ΔE b ) of ionic liquids (ILs) and the UV-Vis absorption spectra of DGNFIL complexes. Further, our results indicate that increasing the size of DGNFs affects the geometrical structure of the surfaces and increases the binding energy of ILs by about 10%. Analysis based on AIM and EDA shows that the interactions between ILs and DGNFs are non-covalent in nature (dispersion energy being dominant) and associated with charge transfer between the IL and nanoflakes. A comparison between the ΔE b values of ILs on DGNFs, GNFs, and h-BN nanoflakes (h-BNNF) shows that the presence of defects on the GNF surfaces increases the binding energy values as follows: DGNFIL > pristine GNFIL > h-BNNFIL. Our calculations indicate that increasing the size of DGNF surfaces leads to a decrease in the HOMO-LUMO energy gap (E g ) of the DGNF surfaces. Orbital energy and density of state calculations show that the E g of DV(SW)-GNFs decreases upon IL adsorption and their Fermi energy level is shifted depending on the type of IL, thus enabling better conductivity. Reactivity descriptors generally indicate that the chemical potential (μ) and chemical hardness (η) of nanoflakes decrease upon IL adsorption, whereas the electrophilicity index (ω) increases. The UV-Vis absorption spectrum of DV-GNF and SW-GNF shows four bands in the visible spectrum which correspond to π → π* transitions with the absorption bands of SW-GNF appearing at higher wavelengths than those of DV-GNF. The most intense absorption bands in DV-GNF (λ = 348 nm) and SW-GNF (λ = 375 nm) are associated with electronic transitions HOMO-1 → LUMO+2 and HOMO → LUMO+1, respectively. In addition
Nucleation of voids and other irradiation-produced defect aggregates

International Nuclear Information System (INIS)

Wiedersich, H.; Katz, J.L.

1976-01-01

The nucleation of defect clusters in crystalline solids from radiation-produced defects is different from the usual nucleation processes in one important aspect: the condensing defects, interstitial atoms and vacancies, can mutually annihilate and are thus similar to matter and antimatter. The nucleation process is described as the simultaneous reaction of vacancies and interstitials (and gas atoms if present) with embryos of all sizes. The reaction rates for acquisition of point defects (and gas atoms) are calculated from their respective jump frequencies and concentrations in the supersaturated system. The reaction rates for emission of point defects are derived from the free energies of the defect clusters in the thermodynamic equilibrium system, i.e., the system without excess point defects. This procedure differs from that used in conventional nucleation theory and permits the inclusion of the ''antimatter'' defect into the set of reaction-rate equations in a straightforward manner. The method is applied to steady-state nucleation, during irradiation, of both dislocation loops and voids in the absence and in the presence of immobile and mobile gas. The predictions of the nucleation theory are shown to be in qualitative agreement with experimental observations, e.g., void densities increase with increasing displacement rates; gases such as helium enhance void nucleation; at low displacement rates and at high temperatures the presence of gas is essential to void formation. For quantitative predictions, the theory must be extended to include the termination of nucleation
Clinical neurogenetics: neurologic presentations of metabolic disorders.

Science.gov (United States)

Kwon, Jennifer M; D'Aco, Kristin E

2013-11-01

This article reviews aspects of the neurologic presentations of selected treatable inborn errors of metabolism within the category of small molecule disorders caused by defects in pathways of intermediary metabolism. Disorders that are particularly likely to be seen by neurologists include those associated with defects in amino acid metabolism (organic acidemias, aminoacidopathies, urea cycle defects). Other disorders of small molecule metabolism are discussed as additional examples in which early treatments have the potential for better outcomes. Copyright © 2013 Elsevier Inc. All rights reserved.
Automatic classification of blank substrate defects

Science.gov (United States)

Boettiger, Tom; Buck, Peter; Paninjath, Sankaranarayanan; Pereira, Mark; Ronald, Rob; Rost, Dan; Samir, Bhamidipati

2014-10-01

Mask preparation stages are crucial in mask manufacturing, since this mask is to later act as a template for considerable number of dies on wafer. Defects on the initial blank substrate, and subsequent cleaned and coated substrates, can have a profound impact on the usability of the finished mask. This emphasizes the need for early and accurate identification of blank substrate defects and the risk they pose to the patterned reticle. While Automatic Defect Classification (ADC) is a well-developed technology for inspection and analysis of defects on patterned wafers and masks in the semiconductors industry, ADC for mask blanks is still in the early stages of adoption and development. Calibre ADC is a powerful analysis tool for fast, accurate, consistent and automatic classification of defects on mask blanks. Accurate, automated classification of mask blanks leads to better usability of blanks by enabling defect avoidance technologies during mask writing. Detailed information on blank defects can help to select appropriate job-decks to be written on the mask by defect avoidance tools [1][4][5]. Smart algorithms separate critical defects from the potentially large number of non-critical defects or false defects detected at various stages during mask blank preparation. Mechanisms used by Calibre ADC to identify and characterize defects include defect location and size, signal polarity (dark, bright) in both transmitted and reflected review images, distinguishing defect signals from background noise in defect images. The Calibre ADC engine then uses a decision tree to translate this information into a defect classification code. Using this automated process improves classification accuracy, repeatability and speed, while avoiding the subjectivity of human judgment compared to the alternative of manual defect classification by trained personnel [2]. This paper focuses on the results from the evaluation of Automatic Defect Classification (ADC) product at MP Mask
A study of the electrical properties of defects in silicon

International Nuclear Information System (INIS)

Blood, A.M.

1998-01-01

This work contains the most comprehensive qualitative and quantitative electron beam induced current (EBIC) study of recombination at contaminated defects in silicon. It is also a rigorous quantitative investigation of the effect of hydrogen on individual transition metal contaminated defects. In addition, the recombination behaviour exhibited by point and extended defects has been investigated using EBIC and deep level transient spectroscopy (DLTS). As a result of these measurements, techniques for the preparation of transition metal contaminated specimens have been refined. Successful hydrogen passivation of copper, nickel and iron contaminated silicon specimens containing oxidation-induced stacking faults has been achieved in two experimental systems. It is found that hydrogen passivates those states that are deepest in the semiconductor band gap in preference to those that are shallow. Furthermore, it has been concluded that during hydrogen passivation treatment, even at low temperatures, unwanted metallic impurities can be introduced. Three types of recombination behaviour have been identified from the defects-studied in this work and they are discussed with relevance to present recombination models. An investigation of the recombination behaviour of defects that lie in the depletion region and in the specimen bulk has concluded that the recombination type observed is independent of the depth of the defect. Evidence for the presence of compound defects showing mixed recombination behaviour type is presented. In conclusion, it is postulated that the transition metal impurities introduce a 'band of states' with a range of energies rather than a single energy state. This proposal is provided as an explanation for the recombination types found in this work and the effect of the hydrogen passivation. This work is placed in context of previous investigations into the behaviour of dislocations in silicon in the presence of transition metals, and the ability of
Holographic Chern-Simons defects

International Nuclear Information System (INIS)

Fujita, Mitsutoshi; Melby-Thompson, Charles M.; Meyer, René; Sugimoto, Shigeki

2016-01-01

We study SU(N) Yang-Mills-Chern-Simons theory in the presence of defects that shift the Chern-Simons level from a holographic point of view by embedding the system in string theory. The model is a D3-D7 system in Type IIB string theory, whose gravity dual is given by the AdS soliton background with probe D7 branes attaching to the AdS boundary along the defects. We holographically renormalize the free energy of the defect system with sources, from which we obtain the correlation functions for certain operators naturally associated to these defects. We find interesting phase transitions when the separation of the defects as well as the temperature are varied. We also discuss some implications for the Fractional Quantum Hall Effect and for 2-dimensional QCD.
Human vision-based algorithm to hide defective pixels in LCDs

Science.gov (United States)

Kimpe, Tom; Coulier, Stefaan; Van Hoey, Gert

2006-02-01

Producing displays without pixel defects or repairing defective pixels is technically not possible at this moment. This paper presents a new approach to solve this problem: defects are made invisible for the user by using image processing algorithms based on characteristics of the human eye. The performance of this new algorithm has been evaluated using two different methods. First of all the theoretical response of the human eye was analyzed on a series of images and this before and after applying the defective pixel compensation algorithm. These results show that indeed it is possible to mask a defective pixel. A second method was to perform a psycho-visual test where users were asked whether or not a defective pixel could be perceived. The results of these user tests also confirm the value of the new algorithm. Our "defective pixel correction" algorithm can be implemented very efficiently and cost-effectively as pixel-dataprocessing algorithms inside the display in for instance an FPGA, a DSP or a microprocessor. The described techniques are also valid for both monochrome and color displays ranging from high-quality medical displays to consumer LCDTV applications.
International conference on defects in insulating crystals

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

Short summaries of conference papers are presented. Some of the conference topics included transport properties, defect levels, superionic conductors, radiation effects, John-Teller effect, electron-lattice interactions, and relaxed excited states. (SDF)
Posterior defects of the patella on CT arthrograms

International Nuclear Information System (INIS)

Lehner, K.; Reiser, M.; Hawe, W.; Smasal, V.; Technische Univ. Muenchen; Technische Univ. Muenchen

1986-01-01

Changes of the posterior bony and cartilaginous surfaces of the patella as seen on CT arthrograms are described in the case of bipartite patellae, fractures and ossification defects. Contrary to present opinion, cartilaginous lesions are frequently seen on CT arthrograms. This is also true for discreet and partial ossification defects which are not visible on conventional X-rays and are described here for the first time. The aetiology, morphogenesis and clinical examples are discussed. (orig.) [de
Neuroradiologic findings in children with mitochondrial disorder: correlation with mitochondrial respiratory chain defects

International Nuclear Information System (INIS)

Kim, Jinna; Lee, Seung-Koo; Kim, Dong Ik; Kim, Eung Yeop; Lee, Young-Mock; Lee, Joon Soo; Kim, Heung Dong

2008-01-01

Mitochondrial disorders are a heterogeneous group of disorders affecting energy metabolism that can present at any age with a wide variety of clinical symptoms. We investigated brain magnetic resonance (MR) findings in 40 children with defects of the mitochondrial respiratory chain (MRC) complex and correlated them with the type of MRC defects. Enrolled were 40 children with MRC defects in biochemical enzyme assay of the muscle specimen. Twenty-one children were found to have classical syndromes of mitochondrial disorders and 19 children presented nonspecific mitochondrial encephalomyopathies. Their brain MR imaging findings were retrospectively reviewed and correlated with the biochemical defect in the MRC complex. Children with MRC defects showed various neuroradiologic features on brain MR imaging that resulted from a complex genetic background and a heterogeneous phenotype. Rapid progression of atrophy involving all structures of the brain with variable involvement of deep gray and white matter are the most frequent MR findings in children with MRC defects in both classical syndromes of mitochondrial disorder and nonspecific mitochondrial encephalomyopathies. The type of biochemical defect in the MRC complex enzyme did not correlate with brain MR findings in child patients. (orig.)
Neuroradiologic findings in children with mitochondrial disorder: correlation with mitochondrial respiratory chain defects

Energy Technology Data Exchange (ETDEWEB)

Kim, Jinna; Lee, Seung-Koo; Kim, Dong Ik [Yonsei University College of Medicine, Department of Radiology, Research Institute of Radiological Science, Seoul (Korea); Kim, Eung Yeop [Yonsei University College of Medicine, Department of Radiology, Research Institute of Radiological Science, Brain Korea 21 Project for Medical Science, Seoul (Korea); Lee, Young-Mock; Lee, Joon Soo [Yonsei University College of Medicine, Department of Pediatrics, Pediatric Epilepsy Clinics, Severance Children' s Hospital, Brain Research Institute, Seoul (Korea); Kim, Heung Dong [Yonsei University College of Medicine, Department of Pediatrics, Pediatric Epilepsy Clinics, Severance Children' s Hospital, Brain Research Institute, Seoul (Korea); Yonsei University College of Medicine, Department of Pediatrics, Seoul (Korea)

2008-08-15

Mitochondrial disorders are a heterogeneous group of disorders affecting energy metabolism that can present at any age with a wide variety of clinical symptoms. We investigated brain magnetic resonance (MR) findings in 40 children with defects of the mitochondrial respiratory chain (MRC) complex and correlated them with the type of MRC defects. Enrolled were 40 children with MRC defects in biochemical enzyme assay of the muscle specimen. Twenty-one children were found to have classical syndromes of mitochondrial disorders and 19 children presented nonspecific mitochondrial encephalomyopathies. Their brain MR imaging findings were retrospectively reviewed and correlated with the biochemical defect in the MRC complex. Children with MRC defects showed various neuroradiologic features on brain MR imaging that resulted from a complex genetic background and a heterogeneous phenotype. Rapid progression of atrophy involving all structures of the brain with variable involvement of deep gray and white matter are the most frequent MR findings in children with MRC defects in both classical syndromes of mitochondrial disorder and nonspecific mitochondrial encephalomyopathies. The type of biochemical defect in the MRC complex enzyme did not correlate with brain MR findings in child patients. (orig.)
Automated defect spatial signature analysis for semiconductor manufacturing process

Science.gov (United States)

Tobin, Jr., Kenneth W.; Gleason, Shaun S.; Karnowski, Thomas P.; Sari-Sarraf, Hamed

1999-01-01

An apparatus and method for performing automated defect spatial signature alysis on a data set representing defect coordinates and wafer processing information includes categorizing data from the data set into a plurality of high level categories, classifying the categorized data contained in each high level category into user-labeled signature events, and correlating the categorized, classified signature events to a present or incipient anomalous process condition.
Surface-defect induced modifications in the optical properties of α-MnO{sub 2} nanorods

Energy Technology Data Exchange (ETDEWEB)

John, Reenu Elizabeth [Department of Physics, St. Berchmans College, Changanassery, Kerala 686101 (India); Chandran, Anoop [School of Pure and Applied Physics, MG University, Kottayam, Kerala 686560 (India); Thomas, Marykutty [Department of Physics, BCM College, Kottayam, Kerala 686001 (India); Jose, Joshy [Department of Physics, St. Berchmans College, Changanassery, Kerala 686101 (India); George, K.C., E-mail: drkcgeorge@gmail.com [Department of Physics, St. Berchmans College, Changanassery, Kerala 686101 (India)

2016-03-30

Graphical abstract: - Highlights: • Alpha-MnO{sub 2} nanorods are prepared by chemical method. • Difference in surface defect density is achieved. • Characterized using XRD, Rietveld, XPS, EDS, HR-TEM, BET, UV–vis absorption spectroscopy and PL spectroscopy. • Explains the bandstructure modification due to Jahn–Teller distortions using crystal field theory. • Modification in the intensity of optical emissions related to defect levels validates the concept of surface defect induced tuning of optical properties. - Abstract: The science of defect engineering via surface tuning opens a new route to modify the inherent properties of nanomaterials for advanced functional and practical applications. In this work, two independent synthesis methods (hydrothermal and co-precipitation) are adopted to fabricate α-MnO{sub 2} nanorods with different defect structures so as to understand the effect of surface modifications on their optical properties. The crystal structure and morphology of samples are investigated with the aid of X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). Atomic composition calculated from energy dispersive spectroscopy (EDS) confirms non-stoichiometry of the samples. The surface properties and chemical environment are thoroughly studied using X-ray photoelectron spectroscopy (XPS) and Brunauer–Emmett–Teller (BET) analysis. Bond angle variance and bond valence sum are determined to validate distortions in the basic MnO{sub 6} octahedron. The surface studies indicate that the concentration of Jahn–Teller manganese (III) (Mn{sup 3+}) ion in the samples differ from each other which results in their distinct properties. Band structure modifications due to Jahn–Teller distortion are examined with the aid of ultraviolet–visible (UV) reflectance and photoluminescence (PL) studies. The dual peaks obtained in derivative spectrum conflict the current concept on the bandgap energy of MnO{sub 2}. These
High resolution deep level transient spectroscopy and process-induced defects in silicon

International Nuclear Information System (INIS)

Evans-Freeman, J.H.; Emiroglu, D.; Vernon-Parry, K.D.

2004-01-01

High resolution, or Laplace, deep level transient spectroscopy (LDLTS) enables the identification of very closely spaced energetic levels in a semiconductor bandgap. DLTS may resolve peaks with a separation of tens of electron volts, but LDLTS can resolve defect energy separations as low as a few MeV. In this paper, we present results from LDLTS applied to ion implantation-induced defects in silicon, with particular emphasis on characterisation of end-of-range interstitial type defects. Silicon was implanted with a variety of ions from mass 28 to 166. A combination of LDLTS and direct capture cross-section measurements was employed to show that electrically active small extended defects were present in the as-implanted samples. Larger dislocations were then generated in Si by oxygenation to act as a control sample. These stacking faults had typical lengths of microns, and their electrical activity was subsequently characterised by LDLTS. This was to establish the sensitivity of LDLTS to defects whose carrier capture is characterised by a non-exponential filling process and an evolving band structure as carrier capture proceeds. The LDLTS spectra show several components in capacitance transients originating from both the end-of-range defects, and the stacking faults, and also clearly show that the carrier emission rates reduce as these extended defects fill with carriers. The end-of-range defects and the stacking faults are shown to have the same electrical behaviour
Defect detection using transient thermography

International Nuclear Information System (INIS)

Mohd Zaki Umar; Ibrahim Ahmad; Ab Razak Hamzah; Wan Saffiey Wan Abdullah

2008-08-01

An experimental research had been carried out to study the potential of transient thermography in detecting sub-surface defect of non-metal material. In this research, eight pieces of bakelite material were used as samples. Each samples had a sub-surface defect in the circular shape with different diameters and depths. Experiment was conducted using one-sided Pulsed Thermal technique. Heating of samples were done using 30 kWatt adjustable quartz lamp while infra red (IR) images of samples were recorded using THV 550 IR camera. These IR images were then analysed with ThermofitTMPro software to obtain the Maximum Absolute Differential Temperature Signal value, ΔΤ m ax and the time of its appearance, τ m ax (ΔΤ). Result showed that all defects were able to be detected even for the smallest and deepest defect (diameter = 5 mm and depth = 4 mm). However the highest value of Differential Temperature Signal (ΔΤ m ax), were obtained at defect with the largest diameter, 20 mm and at the shallowest depth, 1 mm. As a conclusion, the sensitivity of the pulsed thermography technique to detect sub-surface defects of bakelite material is proportionately related with the size of defect diameter if the defects are at the same depth. On the contrary, the sensitivity of the pulsed thermography technique inversely related with the depth of defect if the defects have similar diameter size. (Author)
Anisotropic Magnus Force in Type-II Superconductors with Planar Defects

Science.gov (United States)

Monroy, Ricardo Vega; Gomez, Eliceo Cortés

2015-02-01

The effect of planar defects on the Magnus force in type-II superconductors is studied. It is shown that the deformation of the vortex due to the presence of a planar defect leads to a local decrease in the mean free path of electrons in the vortex. This effect reduces the effective Magnus coefficient in normal direction to the planar defect, leading to an anisotropic regime of the Hall effect. The presented developments here can qualitatively explain experimental observations of the anisotropic Hall effect in high- T c superconductors in the mixed state.
Fetal Valproate Syndrome with Limb Defects: An Indian Case Report

Directory of Open Access Journals (Sweden)

Manisha Goyal

2016-01-01

Full Text Available Epilepsy is a common disorder and exposure to antiepileptic drugs during pregnancy increases the risk of teratogenicity. Older AEDs such as valproate and phenobarbital are associated with a higher risk of major malformations in the fetus than newer AEDs like lamotrigine and levetiracetam. Exposure to valproic acid during first trimester can result in fetal valproate syndrome (FVS, comprising typical facial features, developmental delay, and a variety of malformations such as neural tube defects, cardiac and genitourinary malformations, and limb defects. We are presenting an Indian case of FVS with major limb defects.
Software for roof defects recognition on aerial photographs

Science.gov (United States)

Yudin, D.; Naumov, A.; Dolzhenko, A.; Patrakova, E.

2018-05-01

The article presents information on software for roof defects recognition on aerial photographs, made with air drones. An areal image segmentation mechanism is described. It allows detecting roof defects – unsmoothness that causes water stagnation after rain. It is shown that HSV-transformation approach allows quick detection of stagnation areas, their size and perimeters, but is sensitive to shadows and changes of the roofing-types. Deep Fully Convolutional Network software solution eliminates this drawback. The tested data set consists of the roofing photos with defects and binary masks for them. FCN approach gave acceptable results of image segmentation in Dice metric average value. This software can be used in inspection automation of roof conditions in the production sector and housing and utilities infrastructure.

Subclassification and Clinical Management of Extraction Sockets with Labial Dentoalveolar Dehiscence Defects.

Science.gov (United States)

Chu, Stephen J; Sarnachiaro, Guido O; Hochman, Mark N; Tarnow, Dennis P

2015-01-01

Immediate implant therapy involving implants placed into intact Type 1 extraction sockets has become a consistent clinical technique. The classification of Type 2 extraction sockets, where the mucosal tissues are present but there is a midfacial osseous dehiscence defect, has been described according to the extent of the buccal bone plate absence. The literature has offered different techniques in the treatment of Type 2 sockets; however, the extent of the defect has never been defined or delineated. In this article, the authors describe a subclassification of Type 2 sockets: Type 2A presents with a dehiscence defect roughly 5 mm to 6 mm from the free gingival margin (FGM) involving the coronal one-third of the labial bone plate; Type 2B presents with a dehiscence defect involving the middle one-third of the labial plate, approximately 7 mm to 9 mm from the FGM; and in Type 2C the dehiscence defect involves the apical one-third of the labial osseous plate roughly 10 mm or greater from the FGM. The authors also offer a protocol and technique employing immediate implant placement, guided bone regeneration, and bone graft containment with a custom two-piece healing abutment that can lead to consistent and satisfactory clinical outcomes in low-smile-line patients. The treatment protocol and sequence is outlined in a clinical case presentation involving a Type 2B socket.
Research on the correlation between corona current spectrum and audible noise spectrum of HVDC transmission line

Science.gov (United States)

Liu, Yingyi; Zhou, Lijuan; Liu, Yuanqing; Yuan, Haiwen; Ji, Liang

2017-11-01

Audible noise is closely related to corona current on a high voltage direct current (HVDC) transmission line. In this paper, we measured a large amount of audible noise and corona current waveforms simultaneously based on the largest outdoor HVDC corona cage all over the world. By analyzing the experimental data, the related statistical regularities between a corona current spectrum and an audible noise spectrum were obtained. Furthermore, the generation mechanism of audible noise was analyzed theoretically, and the related mathematical expression between the audible noise spectrum and the corona current spectrum, which is suitable for all of these measuring points in the space, has been established based on the electro-acoustic conversion theory. Finally, combined with the obtained mathematical relation, the internal reasons for these statistical regularities appearing in measured corona current and audible noise data were explained. The results of this paper not only present the statistical association regularities between the corona current spectrum and the audible noise spectrum on a HVDC transmission line, but also reveal the inherent reasons of these associated rules.
Study on defects and impurities in cast-grown polycrystalline silicon substrates for solar cells

International Nuclear Information System (INIS)

Arafune, K.; Sasaki, T.; Wakabayashi, F.; Terada, Y.; Ohshita, Y.; Yamaguchi, M.

2006-01-01

We focused on the defects and impurities in polycrystalline silicon substrates, which deteriorate solar cell efficiency. Comparison of the minority carrier lifetime with the grain size showed that the region with short minority carrier lifetimes did not correspond to the region with small grains. Conversely, the minority carrier lifetime decreased as the etch-pit density (EPD) increased, suggesting that the minority carrier lifetime is strongly affected by the EPD. Electron beam induced current measurements revealed that a combination of grain boundaries and point defects had high recombination activity. Regarding impurities, the interstitial oxygen concentration was relatively low compared with that in a Czochralski-grown silicon substrate, the total carbon concentration exceeded the solubility limit of silicon melt. X-ray microprobe fluorescence measurements revealed a large amount of iron in the regions where there were many etch-pits and grain boundaries with etch-pits. X-ray absorption near edge spectrum analysis revealed trapped iron in the form of oxidized iron
Solar spectrum from 1173 to 1324 A

International Nuclear Information System (INIS)

Chipman, E.; Bruner, E.C. Jr.

1975-01-01

We present some of the results of a rocket flight which obtained a high-resolution stigmatic spectrum of the Sun in the region 1173--1324 A. A list of 179 lines observed in this region is presented, with intensities, widths, and approximate excitation classes for each line. A reproduction and finding chart of the spectrum is included, along with discussion of some individual lines of special interest
Defect studies in electron-irradiated ZnO and GaN

International Nuclear Information System (INIS)

Tuomisto, F.; Look, D.C.; Farlow, G.C.

2007-01-01

We present experimental results obtained with positron annihilation spectroscopy in room-temperature electron-irradiated n-type ZnO and GaN. The cation vacancies act as important compensating centers in 2 MeV electron-irradiated samples, even though their introduction rates are different by 2 orders of magnitude. In addition, negatively charged non-open volume defects that also compensate the n-type conductivity are produced together with the cation vacancies at similar introduction rates. The low introduction rates of compensating defects in ZnO demonstrate the radiation hardness of the material. Isochronal thermal annealings were performed to study the dynamics of the irradiation-induced defects. In 2 MeV electron-irradiated ZnO, all the defects introduced in the irradiation disappear already at 600 K, while 1100 K is needed in GaN. Several separate annealing stages of the defects are observed in both materials, the first at 400 K
Defect studies in electron-irradiated ZnO and GaN

Energy Technology Data Exchange (ETDEWEB)

Tuomisto, F. [Laboratory of Physics, Helsinki University of Technology, 02015 TKK Espoo (Finland)], E-mail: filip.tuomisto@tkk.fi; Look, D.C. [Semiconductor Research Center, Wright State University, Dayton, OH 45435 (United States); Materials and Manufacturing Directorate, Air Force Research Laboratory, Wright-Patterson Air Force Base, OH 45433 (United States); Farlow, G.C. [Physics Department, Wright State University, Dayton, OH 45435 (United States)

2007-12-15

We present experimental results obtained with positron annihilation spectroscopy in room-temperature electron-irradiated n-type ZnO and GaN. The cation vacancies act as important compensating centers in 2 MeV electron-irradiated samples, even though their introduction rates are different by 2 orders of magnitude. In addition, negatively charged non-open volume defects that also compensate the n-type conductivity are produced together with the cation vacancies at similar introduction rates. The low introduction rates of compensating defects in ZnO demonstrate the radiation hardness of the material. Isochronal thermal annealings were performed to study the dynamics of the irradiation-induced defects. In 2 MeV electron-irradiated ZnO, all the defects introduced in the irradiation disappear already at 600 K, while 1100 K is needed in GaN. Several separate annealing stages of the defects are observed in both materials, the first at 400 K.
Eddy Current Testing for Detecting Small Defects in Thin Films

Science.gov (United States)

Obeid, Simon; Tranjan, Farid M.; Dogaru, Teodor

2007-03-01

Presented here is a technique of using Eddy Current based Giant Magneto-Resistance sensor (GMR) to detect surface and sub-layered minute defects in thin films. For surface crack detection, a measurement was performed on a copper metallization of 5-10 microns thick. It was done by scanning the GMR sensor on the surface of the wafer that had two scratches of 0.2 mm, and 2.5 mm in length respectively. In another experiment, metal coatings were deposited over the layers containing five defects with known lengths such that the defects were invisible from the surface. The limit of detection (resolution), in terms of defect size, of the GMR high-resolution Eddy Current probe was studied using this sample. Applications of Eddy Current testing include detecting defects in thin film metallic layers, and quality control of metallization layers on silicon wafers for integrated circuits manufacturing.
Ultrasonic examination of defects close to the outer surface

International Nuclear Information System (INIS)

Benoist, P.; Serre, M.; Champigny, F.

1986-11-01

During the examination of a pressurized water reactor vessel with an in Service Inspection Machine (MIS), various welds are scanned with immersion ultrasonic focused transducers from the inside of the vessel. Defects close to the outer surface are sometimes detected, and sizing with the successive 6 dB drop method leads to oversize some indications; this is caused by various reflections on the outer wall; the corner echo is of particular importance here. CEA and EDF have started an experimental program in order to study the response of volumetric and planar defects located near the outer surface. We present here the first results obtained with artificial defects. 2 refs
Strengthening of defected beam–column joints using CFRP

Directory of Open Access Journals (Sweden)

Mohamed H. Mahmoud

2014-01-01

Full Text Available This paper presents an experimental study for the structural performance of reinforced concrete (RC exterior beam–column joints rehabilitated using carbon-fiber-reinforced polymer (CFRP. The present experimental program consists of testing 10 half-scale specimens divided into three groups covering three possible defects in addition to an adequately detailed control specimen. The considered defects include the absence of the transverse reinforcement within the joint core, insufficient bond length for the beam main reinforcement and inadequate spliced implanted column on the joint. Three different strengthening schemes were used to rehabilitate the defected beam–column joints including externally bonded CFRP strips and sheets in addition to near surface mounted (NSM CFRP strips. The failure criteria including ultimate capacity, mode of failure, initial stiffness, ductility and the developed ultimate strain in the reinforcing steel and CFRP were considered and compared for each group for the control and the CFRP-strengthened specimens. The test results showed that the proposed CFRP strengthening configurations represented the best choice for strengthening the first two defects from the viewpoint of the studied failure criteria. On the other hand, the results of the third group showed that strengthening the joint using NSM strip technique enabled the specimen to outperform the structural performance of the control specimen while strengthening the joints using externally bonded CFRP strips and sheets failed to restore the strengthened joints capacity.
Strengthening of defected beam-column joints using CFRP.

Science.gov (United States)

Mahmoud, Mohamed H; Afefy, Hamdy M; Kassem, Nesreen M; Fawzy, Tarek M

2014-01-01

This paper presents an experimental study for the structural performance of reinforced concrete (RC) exterior beam-column joints rehabilitated using carbon-fiber-reinforced polymer (CFRP). The present experimental program consists of testing 10 half-scale specimens divided into three groups covering three possible defects in addition to an adequately detailed control specimen. The considered defects include the absence of the transverse reinforcement within the joint core, insufficient bond length for the beam main reinforcement and inadequate spliced implanted column on the joint. Three different strengthening schemes were used to rehabilitate the defected beam-column joints including externally bonded CFRP strips and sheets in addition to near surface mounted (NSM) CFRP strips. The failure criteria including ultimate capacity, mode of failure, initial stiffness, ductility and the developed ultimate strain in the reinforcing steel and CFRP were considered and compared for each group for the control and the CFRP-strengthened specimens. The test results showed that the proposed CFRP strengthening configurations represented the best choice for strengthening the first two defects from the viewpoint of the studied failure criteria. On the other hand, the results of the third group showed that strengthening the joint using NSM strip technique enabled the specimen to outperform the structural performance of the control specimen while strengthening the joints using externally bonded CFRP strips and sheets failed to restore the strengthened joints capacity.
Impact of interstitial iron on the study of meta-stable B-O defects in Czochralski silicon: Further evidence of a single defect

Science.gov (United States)

Kim, Moonyong; Chen, Daniel; Abbott, Malcolm; Nampalli, Nitin; Wenham, Stuart; Stefani, Bruno; Hallam, Brett

2018-04-01

We explore the influence of interstitial iron (Fei) on lifetime spectroscopy of boron-oxygen (B-O) related degradation in p-type Czochralski silicon. Theoretical and experimental evidence presented in this study indicate that iron-boron pair (Fe-B) related reactions could have influenced several key experimental results used to derive theories on the fundamental properties of the B-O defect. Firstly, the presence of Fei can account for higher apparent capture cross-section ratios (k) of approximately 100 observed in previous studies during early stages of B-O related degradation. Secondly, the association of Fe-B pairs can explain the initial stage of a two-stage recovery of carrier lifetime with dark annealing after partial degradation. Thirdly, Fei can result in high apparent k values after the permanent deactivation of B-O defects. Subsequently, we show that a single k value can describe the recombination properties associated with B-O defects throughout degradation, that the recovery during dark annealing occurs with a single-stage, and both the fast- and slow-stage B-O related degradation can be permanently deactivated during illuminated annealing. Accounting for the recombination activity of Fei provides further evidence that the B-O defect is a single defect, rather than two separate defects normally attributed to fast-forming recombination centers and slow-forming recombination centers. Implications of this finding for the nature of the B-O defect are also discussed.
Diameter Dependence of Planar Defects in InP Nanowires.

Science.gov (United States)

Wang, Fengyun; Wang, Chao; Wang, Yiqian; Zhang, Minghuan; Han, Zhenlian; Yip, SenPo; Shen, Lifan; Han, Ning; Pun, Edwin Y B; Ho, Johnny C

2016-09-12

In this work, extensive characterization and complementary theoretical analysis have been carried out on Au-catalyzed InP nanowires in order to understand the planar defect formation as a function of nanowire diameter. From the detailed transmission electron microscopic measurements, the density of stacking faults and twin defects are found to monotonically decrease as the nanowire diameter is decreased to 10 nm, and the chemical analysis clearly indicates the drastic impact of In catalytic supersaturation in Au nanoparticles on the minimized planar defect formation in miniaturized nanowires. Specifically, during the chemical vapor deposition of InP nanowires, a significant amount of planar defects is created when the catalyst seed sizes are increased with the lower degree of In supersaturation as dictated by the Gibbs-Thomson effect, and an insufficient In diffusion (or Au-rich enhancement) would lead to a reduced and non-uniform In precipitation at the NW growing interface. The results presented here provide an insight into the fabrication of "bottom-up" InP NWs with minimized defect concentration which are suitable for various device applications.
Nitrotyrosine adsorption on defective graphene: A density functional theory study

Science.gov (United States)

Majidi, R.; Karami, A. R.

2015-06-01

We have applied density functional theory to study adsorption of nitrotyrosine on perfect and defective graphene sheets. The graphene sheets with Stone-Wales (SW) defect, pentagon-nonagon (5-9) single vacancy, and pentagon-octagon-pentagon (5-8-5) double vacancy were considered. The calculations of adsorption energy showed that nitrotyrosine presents a more strong interaction with defective graphene rather than with perfect graphene sheet. The order of interaction strength is: SW>5-9>5-8-5>perfect graphene. It is found that the electronic properties of perfect and defective graphene are sensitive to the presence of nitrotyrosine. Hence, graphene sheets can be considered as a good sensor for detection of nitrotyrosine molecule which is observed in connection with several human disorders, such as Parkinson's and Alzheimer's disease.
Diagnostic outcomes of 27 children referred by pediatricians to a genetics clinic in the Netherlands with suspicion of fetal alcohol spectrum disorders

NARCIS (Netherlands)

Abdelmalik, Nadia; van Haelst, Mieke; Mancini, Grazia; Schrander-Stumpel, Connie; Marcus-Soekarman, Dominique; Hennekam, Raoul; Cobben, Jan Maarten

2013-01-01

The characteristics of fetal alcohol spectrum disorders (FASD) constitute a specific facial phenotype, growth failure and neurodevelopmental defects. Reported FASD prevalences vary widely from 0.08 per 1,000 up to 68.0-89.2 per 1,000. We aimed to evaluate to which extent children referred with a
Fuel defect detection, localization and removal in Bruce Power units 3 through 8

International Nuclear Information System (INIS)

Stone, R.; Armstrong, J.; Iglesias, F.; Oduntan, R.; Lewis, B.

2005-01-01

Fuel element defects are occurring in Bruce 'A' and Bruce 'B' Units. A root-cause investigation is ongoing, however, a solution is not yet in-hand. Fuel defect management efforts have been undertaken, therefore, in the interim. Fuel defect management tools are in-place for all Bruce Units. These tools can be categorized as analysis-based or operations-based. Analysis-based tools include computer codes used primarily for fuel defect characterization, while operations-based tools include Unit-specific delayed-neutron ('DN') monitoring systems and gaseous fission product ('GFP') monitoring systems. Operations-based tools are used for fuel defect detection, localization and removal activities. Fuel and Physics staff use defect detection, localization and removal methodologies and guidelines to disposition fuel defects. Methodologies are 'standardized' or 'routine' procedures for implementing analysis-based and operations-based tools to disposition fuel defects during Unit start-up operation and during operation at high steady-state power levels. Guidelines at present serve to supplement fuel defect management methodologies during Unit power raise. (author)
EUV actinic defect inspection and defect printability at the sub-32 nm half pitch

Energy Technology Data Exchange (ETDEWEB)

Huh, Sungmin; Kearney, Patrick; Wurm, Stefan; Goodwin, Frank; Han, Hakseung; Goldberg, Kenneth; Mochi, Iacopp; Gullikson, Eric M.

2009-08-01

Extreme ultraviolet (EUV) mask blanks with embedded phase defects were inspected with a reticle actinic inspection tool (AIT) and the Lasertec M7360. The Lasertec M7360, operated at SEMA TECH's Mask Blank Development Center (MBDC) in Albany, NY, has a sensitivity to multilayer defects down to 40-45 nm, which is not likely sufficient for mask blank development below the 32 nm half-pitch node. Phase defect printability was simulated to calculate the required defect sensitivity for a next generation blank inspection tool to support reticle development for the sub-32 nm half-pitch technology node. Defect mitigation technology is proposed to take advantage of mask blanks with some defects. This technology will reduce the cost of ownership of EUV mask blanks. This paper will also discuss the kind of infrastructure that will be required for the development and mass production stages.
Valuing spectrum at mm wavelengths for cellular networks

OpenAIRE

Shaw, B. A.; Beltrán, H. F.; Sowerby, K. W.

2017-01-01

This paper investigates the economic value of spectrum at mm wavelengths. The analysis uses four techniques to value spectrum, namely a benchmarking comparison, a discounted cash flow analysis, a real options approach and a deprival method. The methods to calculate spectrum value presented in this paper can be used for any spectrum band and in any country. However, to determine the value of mm wavelengths for cellular networks, we have used data from New Zealand, specifically for the existing...
Implantation processing of Si: A unified approach to understanding ion-induced defects and their impact

International Nuclear Information System (INIS)

Holland, O.W.; Roth, E.G.

1997-05-01

A model is presented to account for the effects of ion-induced defects during implantation processing of Si. It will be shown that processing is quite generally affected by the presence of defect excesses rather than the total number of defects. a defect is considered excess if it represents a surplus locally of one defect type over its compliment. Processing spanning a wide range of implantation conditions will be presented to demonstrate that the majority of the total defects played little or no role in the process. This is a direct result of the ease with which the spatially correlated Frenkel pairs recombine either dynamically or during a post-implantation annealing. Based upon this model, a method will be demonstrated for manipulating or engineering the excess defects to modify their effects. In particular high-energy, self-ions are shown to inject vacancies into a boron implanted region resulting in suppression of transient enhanced diffusion of the dopant
Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

Science.gov (United States)

Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

2015-10-01

Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.
Detection of defects in formed sheet metal using medial axis transformation

Science.gov (United States)

Murmu, Naresh C.; Velgan, Roman

2003-05-01

In the metal forming processes, the sheet metals are often prone to various defects such as thinning, dents, wrinkles etc. In the present manufacturing environments with ever increasing demand of higher quality, detecting the defects of formed sheet metal using an effective and objective inspection system is the foremost norm to remain competitive in market. The defect detection using optical techniques aspire to satisfy its needs to be non-contact and fast. However, the main difficulties to achieve this goal remain essentially on the development of efficient evaluation technique and accurate interpretation of extracted data. The defect like thinning is detected by evaluating the deviations of the thickness in the formed sheet metal against its nominal value. The present evaluation procedure for determination of thickness applied on the measurements data is not without deficiency. To improve this procedure, a new evaluation approach based on medial axis transformation is proposed here. The formed sheet metals are digitized using fringe projection systems in different orientations, and afterwards registered into one coordinate frame. The medial axis transformation (MAT) is applied on the point clouds, generating the point clouds of MAT. This data is further processed and medial surface is determined. The thinning defect is detected by evaluating local wall thickness and other defects like wrinkles are determined using the shape recognition on the medial surface. The applied algorithm is simple, fast and robust.

Point defects and irradiation in oxides: simulations at the atomic scale

International Nuclear Information System (INIS)

Crocombette, J.P.

2005-12-01

The studies done by Jean-Paul Crocombette between 1996 and 2005 in the Service de Recherches de Metallurgie Physique of the Direction de l'Energie Nucleaire in Saclay are presented in this Habilitation thesis. These works were part of the material science researches on the ageing, especially under irradiation, of oxides of interest for the nuclear industry. In this context simulation studies at the atomic scale were performed on two elementary components of ageing under irradiation : point defects and displacement cascades ; using two complementary simulation techniques : ab initio electronic structure calculations and empirical potential molecular dynamics. The first part deals with point defects : self defects (vacancies or interstitials) or hetero-atomic dopants. One first recalls the energetics of such defects in oxides, the specific features of defects calculations and the expected accuracy of these calculations. Then one presents the results obtained on uranium dioxide, oxygen in silver and amorphous silica. The second part tackles the modelling of disintegration recoil nuclei in various?displacement cascades created by crystalline matrices for actinide waste disposal. Cascade calculations give access to the amorphization mechanisms under irradiation of these materials. One thus predicts that the amorphization in zircon takes place directly in the tracks whereas in lanthanum zirconate, the amorphization proceeds through the accumulation of point defects. Finally the prospects of these studies are discussed. (author)
A Study of Defect Behavior in Almandine Garnet

Science.gov (United States)

Geiger, C. A.; Brearley, A. J.; Dachs, E.; Tipplet, G.; Rossman, G. R.

2016-12-01

Transport and diffusion in crystals are controlled by defects. However, a good understanding of the defect types in many silicates, including garnet, is not at hand. We undertook a study on synthetic almandine, ideal end-member Fe3Al2Si3O12, to better understand its precise chemical and physical properties and defect behavior. Crystals were synthesized at high pressures and temperatures under different fO2 conditions using various starting materials with H2O and without. The almandine obtained came in polycrystalline and single-crystal form. The synthetic reaction products and crystals were carefully characterized using X-ray powder diffraction, electron microprobe and TEM analysis and with 57Fe Mössbauer, UV/VIS single-crystal absorption and IR single-crystal spectroscopy. Various possible intrinsic defects, such as the Frenkel, Schottky and site-disorder types, along with Fe3+, in both synthetic and natural almandine crystals, were analyzed based on model defects expressed in Kröger-Vink notation. Certain types of minor microscopic- to macroscopic-sized precipitation or exsolution phases, including some that are nanosized, that are observed in synthetic almandine (e.g., magnetite), as well as in more compositionally complex natural crystals (e.g., magnetite, rutile, ilmenite), may result from defect reactions. An explanation for their origin through minor amounts of defects in garnet has certain advantages over other models that have been put forth in the literature that assume strict garnet stoichiometry for their formation and/or open-system atomic transport over relatively long length scales. Physical properties, including magnetic, electrical conductivity and diffusion behavior, as well as the color, of almandine are also analyzed in terms of various possible model defects. It is difficult, if not impossible, to synthesize stoichiometric end-member almandine, Fe3Al2Si3O12, in the laboratory, as small amounts of extrinsic OH- and/or Fe3+ defects, for example
Early Diagnosis of Autism Spectrum Disorder: Stability and Change in Clinical Diagnosis and Symptom Presentation

Science.gov (United States)

Guthrie, Whitney; Swineford, Lauren B.; Nottke, Charly; Wetherby, Amy M.

2013-01-01

Background: Although a diagnosis of autism spectrum disorder (ASD) appears to be stable in children as young as age three, few studies have explored stability of a diagnosis in younger children. Predictive value of diagnostic tools for toddlers and patterns of symptom change are important considerations for clinicians making early diagnoses. Most…
Surface defects and chiral algebras

Energy Technology Data Exchange (ETDEWEB)

Córdova, Clay [School of Natural Sciences, Institute for Advanced Study,1 Einstein Dr, Princeton, NJ 08540 (United States); Gaiotto, Davide [Perimeter Institute for Theoretical Physics,31 Caroline St N, Waterloo, ON N2L 2Y5 (Canada); Shao, Shu-Heng [School of Natural Sciences, Institute for Advanced Study,1 Einstein Dr, Princeton, NJ 08540 (United States)

2017-05-26

We investigate superconformal surface defects in four-dimensional N=2 superconformal theories. Each such defect gives rise to a module of the associated chiral algebra and the surface defect Schur index is the character of this module. Various natural chiral algebra operations such as Drinfeld-Sokolov reduction and spectral flow can be interpreted as constructions involving four-dimensional surface defects. We compute the index of these defects in the free hypermultiplet theory and Argyres-Douglas theories, using both infrared techniques involving BPS states, as well as renormalization group flows onto Higgs branches. In each case we find perfect agreement with the predicted characters.
Presentation of a novel model of chitosan- polyethylene oxide-nanohydroxyapatite nanofibers together with bone marrow stromal cells to repair and improve minor bone defects

Directory of Open Access Journals (Sweden)

Asgar Emamgholi

2015-09-01

Full Text Available Objective(s:Various methods for repairing bone defects are presented. Cell therapy is one of these methods. Bone marrow stromal cells (BMSCs seem to be suitable for this purpose. On the other hand, lots of biomaterials are used to improve and repair the defect in the body, so in this study we tried to produce a similar structure to the bone by the chitosan and hydroxyapatite. Materials and Methods: In this study, the solution of chitosan-nanohydroxyapatite-polyethylene oxide (PEO Nanofibers was produced by electrospinning method, and then the BMSCs were cultured on this solution. A piece of chitosan-nanohydroxyapatite Nanofibers with BMSCs was placed in a hole with the diameter of 1 mm at the distal epiphysis of the rat femur. Then the biomechanical and radiographic studies were performed. Results: Biomechanical testing results showed that bone strength was significantly higher in the Nanofiber/BMSCs group in comparison with control group. Also the bone strength in nanofiber/BMSCs group was significant, but in nanofiber group was nearly significant. Radiographic studies also showed that the average amount of callus formation (radio opacity in nanofiber and control group was not significantly different. The callus formation in nanofiber/BMSCs group was increased compared to the control group, and it was not significant in the nanofiber group. Conclusion: Since chitosan-nanohydroxyapatite nanofibers with BMSCs increases the rate of bone repair, the obtained cell-nanoscaffold shell can be used in tissue engineering and cell therapy, especially for bone defects.
TVWS devices spectrum mask test and analysis

CSIR Research Space (South Africa)

Lamola, MM

2016-09-01

Full Text Available Dynamic Spectrum Access (DSA) plays a vital role in opportunistic access to spectrum. A key component of DSA is preventing interference to the incumbent (primary) user from the secondary user. We present the results of an experiment to analyze...
Laterality defects in the national birth defects prevention study 1998-2007 birth prevalence and descriptive epidemiology

Science.gov (United States)

Little is known epidemiologically about laterality defects. Using data from the National Birth Defects Prevention Study (NBDPS), a large multi-site case-control study of birth defects, we analyzed prevalence and selected characteristics in children born with laterality defects born from 1998 to 2007...
Sum Utilization of Spectrum with Spectrum Handoff and Imperfect Sensing in Interweave Multi-Channel Cognitive Radio Networks

Directory of Open Access Journals (Sweden)

Waqas Khalid

2018-05-01

Full Text Available Fifth-generation (5G heterogeneous network deployment poses new challenges for 5G-based cognitive radio networks (5G-CRNs as the primary user (PU is required to be more active because of the small cells, random user arrival, and spectrum handoff. Interweave CRNs (I-CRNs improve spectrum utilization by allowing opportunistic spectrum access (OSA for secondary users (SUs. The sum utilization of spectrum, i.e., joint utilization of spectrum by the SU and PU, depends on the spatial and temporal variations of PU activities, sensing outcomes, transmitting conditions, and spectrum handoff. In this study, we formulate and analyze the sum utilization of spectrum with different sets of channels under different PU and SU co-existing network topologies. We consider realistic multi-channel scenarios for the SU, with each channel licensed to a PU. The SU, aided by spectrum handoff, is authorized to utilize the channels on the basis of sensing outcomes and PU interruptions. The numerical evaluation of the proposed work is presented under different network and sensing parameters. Moreover, the sum utilization gain is investigated to analyze the sensitivities of different sensing parameters. It is demonstrated that different sets of channels, PU activities, and sensing outcomes have a significant impact on the sum utilization of spectrum associated with a specific network topology.
Cognitive Spectrum Efficient Multiple Access Technique using Relay Systems

DEFF Research Database (Denmark)

Frederiksen, Flemming Bjerge; Prasad, Ramjee

2007-01-01

Methods to enhance the use of the frequency spectrum by automatical spectrum sensing plus spectrum sharing in a cognitive radio technology context will be presented and discussed in this paper. Ideas to increase the coverage of cellular systems by relay channels, relay stations and collaborate...
Planck 2013 results. XXV. Searches for cosmic strings and other topological defects

CERN Document Server

Ade, P.A.R.; Armitage-Caplan, C.; Arnaud, M.; Ashdown, M.; Atrio-Barandela, F.; Aumont, J.; Baccigalupi, C.; Banday, A.J.; Barreiro, R.B.; Bartlett, J.G.; Bartolo, N.; Battaner, E.; Battye, R.; Benabed, K.; Benoit, A.; Benoit-Levy, A.; Bernard, J.P.; Bersanelli, M.; Bielewicz, P.; Bobin, J.; Bock, J.J.; Bonaldi, A.; Bonavera, L.; Bond, J.R.; Borrill, J.; Bouchet, F.R.; Bridges, M.; Bucher, M.; Burigana, C.; Butler, R.C.; Cardoso, J.F.; Catalano, A.; Challinor, A.; Chamballu, A.; Chiang, L.Y.; Chiang, H.C.; Christensen, P.R.; Church, S.; Clements, D.L.; Colombi, S.; Colombo, L.P.L.; Couchot, F.; Coulais, A.; Crill, B.P.; Curto, A.; Cuttaia, F.; Danese, L.; Davies, R.D.; Davis, R.J.; de Bernardis, P.; de Rosa, A.; de Zotti, G.; Delabrouille, J.; Delouis, J.M.; Desert, F.X.; Diego, J.M.; Dole, H.; Donzelli, S.; Dore, O.; Douspis, M.; Ducout, A.; Dunkley, J.; Dupac, X.; Efstathiou, G.; Ensslin, T.A.; Eriksen, H.K.; Fergusson, J.; Finelli, F.; Forni, O.; Frailis, M.; Franceschi, E.; Galeotta, S.; Ganga, K.; Giard, M.; Giardino, G.; Giraud-Heraud, Y.; Gonzalez-Nuevo, J.; Gorski, K.M.; Gratton, S.; Gregorio, A.; Gruppuso, A.; Hansen, F.K.; Hanson, D.; Harrison, D.; Henrot-Versille, S.; Hernandez-Monteagudo, C.; Herranz, D.; Hildebrandt, S.R.; Hivon, E.; Hobson, M.; Holmes, W.A.; Hornstrup, A.; Hovest, W.; Huffenberger, K.M.; Jaffe, T.R.; Jaffe, A.H.; Jones, W.C.; Juvela, M.; Keihanen, E.; Keskitalo, R.; Kisner, T.S.; Knoche, J.; Knox, L.; Kunz, M.; Kurki-Suonio, H.; Lagache, G.; Lahteenmaki, A.; Lamarre, J.M.; Lasenby, A.; Laureijs, R.J.; Lawrence, C.R.; Leahy, J.P.; Leonardi, R.; Lesgourgues, J.; Liguori, M.; Lilje, P.B.; Linden-Vornle, M.; Lopez-Caniego, M.; Lubin, P.M.; Macias-Perez, J.F.; Maffei, B.; Maino, D.; Mandolesi, N.; Maris, M.; Marshall, D.J.; Martin, P.G.; Martinez-Gonzalez, E.; Masi, S.; Matarrese, S.; Matthai, F.; Mazzotta, P.; McEwen, J.D.; Melchiorri, A.; Mendes, L.; Mennella, A.; Migliaccio, M.; Mitra, S.; Miville-Deschenes, M.A.; Moneti, A.; Montier, L.; Morgante, G.; Mortlock, D.; Moss, A.; Munshi, D.; Naselsky, P.; Natoli, P.; Netterfield, C.B.; Norgaard-Nielsen, H.U.; Noviello, F.; Novikov, D.; Novikov, I.; Osborne, S.; Oxborrow, C.A.; Paci, F.; Pagano, L.; Pajot, F.; Paoletti, D.; Pasian, F.; Patanchon, G.; Peiris, H.V.; Perdereau, O.; Perotto, L.; Perrotta, F.; Piacentini, F.; Piat, M.; Pierpaoli, E.; Pietrobon, D.; Plaszczynski, S.; Pointecouteau, E.; Polenta, G.; Ponthieu, N.; Popa, L.; Poutanen, T.; Pratt, G.W.; Prezeau, G.; Prunet, S.; Puget, J.L.; Rachen, J.P.; Rath, C.; Rebolo, R.; Remazeilles, M.; Renault, C.; Ricciardi, S.; Riller, T.; Ringeval, C.; Ristorcelli, I.; Rocha, G.; Rosset, C.; Roudier, G.; Rowan-Robinson, M.; Rusholme, B.; Sandri, M.; Santos, D.; Savini, G.; Scott, D.; Seiffert, M.D.; Shellard, E.P.S.; Spencer, L.D.; Starck, J.L.; Stolyarov, V.; Stompor, R.; Sudiwala, R.; Sureau, F.; Sutton, D.; Suur-Uski, A.S.; Sygnet, J.F.; Tauber, J.A.; Tavagnacco, D.; Terenzi, L.; Toffolatti, L.; Tomasi, M.; Tristram, M.; Tucci, M.; Tuovinen, J.; Valenziano, L.; Valiviita, J.; Van Tent, B.; Varis, J.; Vielva, P.; Villa, F.; Vittorio, N.; Wade, L.A.; Wandelt, B.D.; Yvon, D.; Zacchei, A.; Zonca, A.

2014-01-01

Planck data have been used to provide stringent new constraints on cosmic strings and other defects. We describe forecasts of the CMB power spectrum induced by cosmic strings, calculating these from network models and simulations using line-of-sight Boltzmann solvers. We have studied Nambu-Goto cosmic strings, as well as field theory strings for which radiative effects are important, thus spanning the range of theoretical uncertainty in strings models. We have added the angular power spectrum from strings to that for a simple adiabatic model, with the extra fraction defined as $f_{10}$ at multipole $\\ell=10$. This parameter has been added to the standard six parameter fit using COSMOMC with flat priors. For the Nambu-Goto string model, we have obtained a constraint on the string tension of $G\\mu/c^2 < 1.5 x 10^{-7}$ and $f_{10} < 0.015$ at 95% confidence that can be improved to $G\\mu/c^2 < 1.3 x 10^{-7}$ and $f_{10} < 0.010$ on inclusion of high-$\\ell$ CMB data. For the abelian-Higgs field theory ...
Testing of defects in Si semiconductor apparatus by using single-photon detection

International Nuclear Information System (INIS)

Zhongliang, Pan; Ling, Chen; Guangju, Chen

2013-01-01

The failure analysis of semiconductor apparatus is very needed for ensuring product quality, which can find several types of defects in the semiconductor apparatus. A new testing method for the defects in Si semiconductor apparatus is presented in this paper, the method makes use of photon emissions to find out the failure positions or failure components by taking advantage of the infrared photo emission characteristics of semiconductor apparatus. These emitted photons carry the information of the apparatus structure. If there are defects in the apparatus, these photons can help in understanding the apparatus properties and detecting the defects. An algorithm for the generation of circuit input vectors are presented in this paper to enhance the strength of the emitted photons for the given components in the semiconductor apparatus. The multiple-valued logic, the static timing analysis and path sensitizations, are used in the algorithm. A lot of experimental results for the Si semiconductor apparatus show that many types of defects such as contact spiking and latchup failure etc., can be detected accurately by the method proposed in this paper
Real-time defect detection on highly reflective curved surfaces

Science.gov (United States)

Rosati, G.; Boschetti, G.; Biondi, A.; Rossi, A.

2009-03-01

This paper presents an automated defect detection system for coated plastic components for the automotive industry. This research activity came up as an evolution of a previous study which employed a non-flat mirror to illuminate and inspect high reflective curved surfaces. According to this method, the rays emitted from a light source are conveyed on the surface under investigation by means of a suitably curved mirror. After the reflection on the surface, the light rays are collected by a CCD camera, in which the coating defects appear as shadows of various shapes and dimensions. In this paper we present an evolution of the above-mentioned method, introducing a simplified mirror set-up in order to reduce the costs and the complexity of the defect detection system. In fact, a set of plane mirrors is employed instead of the curved one. Moreover, the inspection of multiple bend radius parts is investigated. A prototype of the machine vision system has been developed in order to test this simplified method. This device is made up of a light projector, a set of plane mirrors for light rays reflection, a conveyor belt for handling components, a CCD camera and a desktop PC which performs image acquisition and processing. Like in the previous system, the defects are identified as shadows inside a high brightness image. At the end of the paper, first experimental results are presented.
CD and defect improvement challenges for immersion processes

Science.gov (United States)

Ehara, Keisuke; Ema, Tatsuhiko; Yamasaki, Toshinari; Nakagawa, Seiji; Ishitani, Seiji; Morita, Akihiko; Kim, Jeonghun; Kanaoka, Masashi; Yasuda, Shuichi; Asai, Masaya

2009-03-01

The intention of this study is to develop an immersion lithography process using advanced track solutions to achieve world class critical dimension (CD) and defectivity performance in a state of the art manufacturing facility. This study looks at three important topics for immersion lithography: defectivity, CD control, and wafer backside contamination. The topic of defectivity is addressed through optimization of coat, develop, and rinse processes as well as implementation of soak steps and bevel cleaning as part of a comprehensive defect solution. Develop and rinse processing techniques are especially important in the effort to achieve a zero defect solution. Improved CD control is achieved using a biased hot plate (BHP) equipped with an electrostatic chuck. This electrostatic chuck BHP (eBHP) is not only able to operate at a very uniform temperature, but it also allows the user to bias the post exposure bake (PEB) temperature profile to compensate for systematic within-wafer (WiW) CD non-uniformities. Optimized CD results, pre and post etch, are presented for production wafers. Wafer backside particles can cause focus spots on an individual wafer or migrate to the exposure tool's wafer stage and cause problems for a multitude of wafers. A basic evaluation of the cleaning efficiency of a backside scrubber unit located on the track was performed as a precursor to a future study examining the impact of wafer backside condition on scanner focus errors as well as defectivity in an immersion scanner.
Ultrasonic determination of the size of defects

International Nuclear Information System (INIS)

Zetterwall, T.

1989-01-01

The paper presents results from a study of ultrasonic testing of materials. The main topic has been the determination of the size, length and deep, of cracks or defects in stainless steel plates. (K.A.E)
Apparatus for locating defective nuclear fuel elements

International Nuclear Information System (INIS)

Lawrie, W.E.

1979-01-01

An ultrasonic search unit for locating defective fuel elements within a fuel assembly used in a water cooled nuclear reactor is presented. The unit is capable of freely traversing the restricted spaces between the fuel elements
Defect driven tailoring of colossal dielectricity of Reduced Graphene Oxide

Energy Technology Data Exchange (ETDEWEB)

Sarkar, S.; Mondal, A. [Department of Physics, Jadavpur University, Kolkata 700 032 (India); Dey, K. [Department of Solid State Physics, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700 032 (India); Ray, R., E-mail: juphyruma@gmail.com [Department of Physics, Jadavpur University, Kolkata 700 032 (India)

2016-02-15

Highlights: • Reduced graphene oxides (RGO) are prepared by two chemical routes. • Defects in RGO are characterized by Raman, FTIR and XPS studies. • Defects tailor colossal dielectricity in RGO. - Abstract: Reduced graphene oxide (RGO) is prepared in two different chemical routes where reduction of graphene oxide is performed by hydrazine hydrate and through high pressure in hydrothermal reactor. Samples are characterized by X-ray powdered diffraction (XRD), thermo gravimetric analysis (TGA), field emission scanning electron microscopy (FESEM) and tunneling electron microscopy (TEM). Types of defects are probed by Raman, FTIR spectroscopy and X-ray photoelectron spectroscopy (XPS). UV–vis absorption reveals different optical band gaps of the two RGOs. Conductivity mechanism is studied through I–V measurements displaying different characteristic features which are addressed due to the presence of defects appeared in different synthesis. Significantly high value (∼10{sup 4}) of dielectric permittivity at 10 MHz is attractive for technological application which could be tuned by the defects present in RGO.
Die Defects and Die Corrections in Metal Extrusion

Directory of Open Access Journals (Sweden)

Sayyad Zahid Qamar

2018-05-01

Full Text Available Extrusion is a very popular and multi-faceted manufacturing process. A large number of products for the automotive, aerospace, and construction sectors are produced through aluminum extrusion. Many defects in the extruded products occur because of the conditions of the dies and tooling. The problems in dies can be due to material issues, design and manufacturing, or severe usage. They can be avoided by maintaining the billet quality, by controlling the extrusion process parameters, and through routine maintenance. Die problems that occur on a day-to-day basis are mostly repairable and are rectified through various types of die correction operations. These defects and repair operations have not been reported in detail in the published literature. The current paper presents an in-depth description of repairable die defects and related die correction operations in metal extrusion. All major die defects are defined and classified, and their causes, preventive measures, and die correction operations are described. A brief frequency-based statistical study of die defects is also carried out to identify the most frequent die corrections. This work can be of direct benefit to plant engineers and operators and to researchers and academics in the field of metal extrusion.
Optical coherence tomography use in the diagnosis of enamel defects

Science.gov (United States)

Al-Azri, Khalifa; Melita, Lucia N.; Strange, Adam P.; Festy, Frederic; Al-Jawad, Maisoon; Cook, Richard; Parekh, Susan; Bozec, Laurent

2016-03-01

Molar incisor hypomineralization (MIH) affects the permanent incisors and molars, whose undermineralized matrix is evidenced by lesions ranging from white to yellow/brown opacities to crumbling enamel lesions incapable of withstanding normal occlusal forces and function. Diagnosing the condition involves clinical and radiographic examination of these teeth, with known limitations in determining the depth extent of the enamel defects in particular. Optical coherence tomography (OCT) is an emerging hard and soft tissue imaging technique, which was investigated as a new potential diagnostic method in dentistry. A comparison between the diagnostic potential of the conventional methods and OCT was conducted. Compared to conventional imaging methods, OCT gave more information on the structure of the enamel defects as well as the depth extent of the defects into the enamel structure. Different types of enamel defects were compared, each type presenting a unique identifiable pattern when imaged using OCT. Additionally, advanced methods of OCT image analysis including backscattered light intensity profile analysis and enface reconstruction were performed. Both methods confirmed the potential of OCT in enamel defects diagnosis. In conclusion, OCT imaging enabled the identification of the type of enamel defect and the determination of the extent of the enamel defects in MIH with the advantage of being a radiation free diagnostic technique.
CISAPS: Complex Informational Spectrum for the Analysis of Protein Sequences

Directory of Open Access Journals (Sweden)

Charalambos Chrysostomou

2015-01-01

Full Text Available Complex informational spectrum analysis for protein sequences (CISAPS and its web-based server are developed and presented. As recent studies show, only the use of the absolute spectrum in the analysis of protein sequences using the informational spectrum analysis is proven to be insufficient. Therefore, CISAPS is developed to consider and provide results in three forms including absolute, real, and imaginary spectrum. Biologically related features to the analysis of influenza A subtypes as presented as a case study in this study can also appear individually either in the real or imaginary spectrum. As the results presented, protein classes can present similarities or differences according to the features extracted from CISAPS web server. These associations are probable to be related with the protein feature that the specific amino acid index represents. In addition, various technical issues such as zero-padding and windowing that may affect the analysis are also addressed. CISAPS uses an expanded list of 611 unique amino acid indices where each one represents a different property to perform the analysis. This web-based server enables researchers with little knowledge of signal processing methods to apply and include complex informational spectrum analysis to their work.
The fractal character of radiation defects aggregation in crystals

International Nuclear Information System (INIS)

Akylbekov, A.; Akimbekov, E.; Baktybekov, K.; Vasil'eva, I.

2002-01-01

In processes of self-organization, which characterize open systems, the source of ordering is a non-equilibrium. One of the samples of ordering system is radiation-stimulated aggregation of defects in solids. In real work the analysis of criterions of ordering defects structures in solid, which is continuously irradiate at low temperature is presented. The method of cellular automata used in simulation of irradiation. It allowed us to imitate processes of defects formation and recombination. The simulation realized on the surfaces up to 1000x1000 units with initial concentration of defects C n (the power of dose) 0.1-1 %. The number of iterations N (duration of irradiation) mounted to 10 6 cycles. The single centers, which are the sources of formation aggregates, survive in the result of probabilistic nature of formation and recombination genetic pairs of defects and with strictly fixed radius of recombination (the minimum inter anionic distance). For determination the character of same type defects distribution the potential of their interaction depending of defects type and reciprocal distance is calculated. For more detailed study of processes, proceeding in cells with certain sizes of aggregates, the time dependence of potential interaction is constructed. It is shown, that on primary stage the potential is negative, then it increase and approach the saturation in positive area. The minimum of interaction potential corresponds to state of physical chaos in system. Its increasing occurs with formation of same type defects aggregates. Further transition to saturation and 'undulating' character of curves explains by formation and destruction aggregates. The data indicated that - these processes occur simultaneously in cells with different sizes. It allows us to assume that the radiation defects aggregation have a fractal nature

Defect design of insulation systems for photovoltaic modules

Science.gov (United States)

Mon, G. R.

1981-01-01

A defect-design approach to sizing electrical insulation systems for terrestrial photovoltaic modules is presented. It consists of gathering voltage-breakdown statistics on various thicknesses of candidate insulation films where, for a designated voltage, module failure probabilities for enumerated thickness and number-of-layer film combinations are calculated. Cost analysis then selects the most economical insulation system. A manufacturing yield problem is solved to exemplify the technique. Results for unaged Mylar suggest using fewer layers of thicker films. Defect design incorporates effects of flaws in optimal insulation system selection, and obviates choosing a tolerable failure rate, since the optimization process accomplishes that. Exposure to weathering and voltage stress reduces the voltage-withstanding capability of module insulation films. Defect design, applied to aged polyester films, promises to yield reliable, cost-optimal insulation systems.
Defect diffusion during annealing of low-energy ion-implanted silicon

International Nuclear Information System (INIS)

Bedrossian, P.J.; Caturla, M.J.; Diaz de la Rubia, T.

1997-01-01

The authors present a new approach for investigating the kinetics of defect migration during annealing of low-energy, ion-implanted silicon, employing a combination of computer simulations and atomic-resolution tunneling microscopy. Using atomically-clean Si(111)-7 x 7 as a sink for bulk point defects created by 5 keV Xe and Ar irradiation, they observe distinct, temperature-dependent surface arrival rates for vacancies and interstitials. A combination of simulation tools provides a detailed description of the processes that underlie the observed temperature-dependence of defect segregation, and the predictions of the simulations agree closely with the experimental observations
48 CFR 1615.407-1 - Rate reduction for defective pricing or defective cost or pricing data.

Science.gov (United States)

2010-10-01

... defective pricing or defective cost or pricing data. 1615.407-1 Section 1615.407-1 Federal Acquisition... CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Contract Pricing 1615.407-1 Rate reduction for defective pricing or defective cost or pricing data. The clause set forth in section 1652.215-70...
48 CFR 1652.215-70 - Rate Reduction for Defective Pricing or Defective Cost or Pricing Data.

Science.gov (United States)

2010-10-01

... Defective Pricing or Defective Cost or Pricing Data. 1652.215-70 Section 1652.215-70 Federal Acquisition... CLAUSES AND FORMS CONTRACT CLAUSES Texts of FEHBP Clauses 1652.215-70 Rate Reduction for Defective Pricing or Defective Cost or Pricing Data. As prescribed in 1615.407-1, the following clause shall be...
Fully Ab-Initio Determination of the Thermoelectric Properties of Half-Heusler NiTiSn: Crucial Role of Interstitial Ni Defects.

Science.gov (United States)

Berche, Alexandre; Jund, Philippe

2018-05-23

For thermoelectric applications, ab initio methods generally fail to predict the transport properties of the materials because of their inability to predict properly the carrier concentrations that control the electronic properties. In this work, a methodology to fill in this gap is applied on the NiTiSn half Heusler phase. For that, we show that the main defects act as donor of electrons and are responsible of the electronic properties of the material. Indeed, the presence of Ni i interstitial defects explains the experimental valence band spectrum and its associated band gap reported in the literature. Moreover, combining the DOS of the solid solutions with the determination of the energy of formation of charged defects, we show that Ni i defects are also responsible of the measured carrier concentration in experimentally supposed "pure" NiTiSn compounds. Subsequently the thermoelectric properties of NiTiSn can be calculated using a fully ab initio description and an overall correct agreement with experiments is obtained. This methodology can be extended to predict the result of extrinsic doping and thus to select the most efficient dopant for specific thermoelectric applications.
Intrinsic defects in silicon carbide for spin-based quantum applications

International Nuclear Information System (INIS)

Vladimir Dyakonov

2014-01-01

We present a set of experiments demonstrating a high potential of atomic-scale defects in SiC for various spin-based applications, including quantum information processing and photonics. In particular, we show that defect spn qubits in SiC can be addressed, manipulated and selectively read out by means of the double radio-optical resonance. The situation reminds the one in the atomic spectroscopy, where the atoms have their individual extremely sharp optical and RF resonance fingerprints. We also generate inverse population in some intrinsic defects, resulting in stimulated microwave emission at RT. This is a crucial step towards implementation of highly-integrable solid-state masers and extraordinarily sensitive microwave detectors. As an application example, we incorporate intrinsic defects in LED structures and show that they can be electrically driven at room temperature. (author)
Successful conservative management of symptomatic bilateral dorsal patellar defects presenting with cartilage involvement and bone marrow edema : MRI findings

NARCIS (Netherlands)

Kwee, Thomas C.; Sonneveld, Heleen; Nix, Maarten

2016-01-01

The dorsal patellar defect is a relatively rare entity that involves the superolateral quadrant of the patella. It is usually considered to represent a delayed ossification process, although its exact origin remains unclear. Because of its usually innocuous nature and clinical course, invasive
Can You Tell Me Something about Yourself?: Self-Presentation in Children and Adolescents with High Functioning Autism Spectrum Disorder in Hypothetical and Real Life Situations

Science.gov (United States)

Scheeren, Anke M.; Begeer, Sander; Banerjee, Robin; Terwogt, Mark Meerum; Koot, Hans M.

2010-01-01

The self-presentation skills of children and adolescents with high-functioning autistic spectrum disorder (HFASD) and typically developing (TD) controls were compared, in response to both hypothetical and real life situations. In both situations, 26 HFASD and 26 TD participants were prompted to describe themselves twice, first in a baseline…
Non-stoichiometry Defects and Radiation Hardness of Lead Tungstate Crystals PbWO4

CERN Document Server

Devitsin, E G; Kozlov, V A; Nefedov, L; Polyansky, E V; Potashov, S Yu; Terkulov, A R; Zadneprovski, B I

2001-01-01

It has been stated many times that the formation of radiation infringements in PbWO4 is to big extent stipulated by non-stoichiometry defects of the crystals, arising in the process of their growth and annealing. To refine the idea of characteristics of non-stoichiometry defects and their effect on the radiation hardness of PbWO4 the current study is aimed at the melt composition infringements during its evaporation and at optical transmission of crystals obtained in these conditions after their irradiation (137Cs source). In the optical transmission measurements along with traditional techniques a method "in situ" was used, which provided the measurements in fixed points of the spectrum (380, 470 and 535 nm) directly in the process of the irradiation. X-ray phase and fluorescence analysis of condensation products of vapours over PbWO4 melt has found PbWO4 phase in their content as well as compounds rich in lead, PbO, Pb2WO5, with overall ratio Pb/W = 3.2. Correspondingly the lack of lead and variations in th...
Enamel Defects of Human Primary Dentition as Virtual Memory of Early Developmental Events

Directory of Open Access Journals (Sweden)

Naser Asl Aminabadi

2009-12-01

Full Text Available Background and aims. The objectives of the present study were to investigate the prevalence and the position of enamel defects of primary teeth and hence to estimate the approximate time of an insult. Material and methods. 121 children aged 3 to 5 years were included in the study. The Modified Developmental Defects of Enamel Index was used to diagnose and classify the defects. The defects were categorized as hypoplasia, hypocalcification or a combination of them. Each tooth was investigated for occlusal/incisal, middle, cervical, incisomiddle, cervicomiddle and complete crown defects. Results. 55.37% of the children were affected by enamel defects, 23.96% being categorized as hypocalcification and 22.31% as hypoplasia. The enamel defects were more abundant in maxillary primary incisors and mandibular primary canines. Minimum involvement was seen in maxillary primary second molars and mandibular primary lateral incisors. The prevalence of cervical defects in maxillary primary incisors was significantly more than the middle or incisal defects (P < 0.05. The prevalence of incisal defects in mandibular primary incisors was significantly more than the middle or cervical defects (P < 0.05. Conclusions. The results revealed a considerable number of enamel defects which are multiple, symmetric and chronologically accordant with the estimated neonatal line in primary teeth of healthy children.
Structure, stability and mobility of point defects in hexagonal close packed zirconium: an ab initio study

International Nuclear Information System (INIS)

Verite, G.

2007-09-01

This research aims at determining, by means of DFT (density functional theory) electronic structure computations, the structure, the stability, and the mobility of isolated point defects, lack defects, auto-interstitial defects, or small aggregate defects in the compact hexagonal zirconium (hc Zr). After a literature survey on the studied materials and a review of computer simulation methods in material science, the author presents and comments the available results from experiments or simulations on point defects in hc Zr. He presents the growth phenomenon under radiation. Then, he briefly described the computing techniques used in this study, reports the determination of the network parameters and elastic constants of each material. He reports and comments the results obtained with the SIESTA code and with a Monte Carlo kinetic simulation. The different types of defects are investigated
Support for calcium channel gene defects in autism spectrum disorders

Directory of Open Access Journals (Sweden)

Lu Ake Tzu-Hui

2012-12-01

Full Text Available Abstract Background Alternation of synaptic homeostasis is a biological process whose disruption might predispose children to autism spectrum disorders (ASD. Calcium channel genes (CCG contribute to modulating neuronal function and evidence implicating CCG in ASD has been accumulating. We conducted a targeted association analysis of CCG using existing genome-wide association study (GWAS data and imputation methods in a combined sample of parent/affected child trios from two ASD family collections to explore this hypothesis. Methods A total of 2,176 single-nucleotide polymorphisms (SNP (703 genotyped and 1,473 imputed covering the genes that encode the α1 subunit proteins of 10 calcium channels were tested for association with ASD in a combined sample of 2,781 parent/affected child trios from 543 multiplex Caucasian ASD families from the Autism Genetics Resource Exchange (AGRE and 1,651 multiplex and simplex Caucasian ASD families from the Autism Genome Project (AGP. SNP imputation using IMPUTE2 and a combined reference panel from the HapMap3 and the 1,000 Genomes Project increased coverage density of the CCG. Family-based association was tested using the FBAT software which controls for population stratification and accounts for the non-independence of siblings within multiplex families. The level of significance for association was set at 2.3E-05, providing a Bonferroni correction for this targeted 10-gene panel. Results Four SNPs in three CCGs were associated with ASD. One, rs10848653, is located in CACNA1C, a gene in which rare de novo mutations are responsible for Timothy syndrome, a Mendelian disorder that features ASD. Two others, rs198538 and rs198545, located in CACN1G, and a fourth, rs5750860, located in CACNA1I, are in CCGs that encode T-type calcium channels, genes with previous ASD associations. Conclusions These associations support a role for common CCG SNPs in ASD.
Pupillary anomaly masquerading as a glaucomatous visual field defect: a case report

Directory of Open Access Journals (Sweden)

Tey Adrian

2004-06-01

Full Text Available Abstract Background Patients are often referred to ophthalmologists with focal visual field defects on routine testing, possibly related to a potential diagnosis of glaucoma. However, examination of the individual patient's ocular characteristics as well as facial characteristics may often reveal a cause of the visual field defect. Case presentation We describe a patient who was found to have a superior visual field defect on routine testing by the optician. Repeat perimetry with pharmacological dilatation of the pupil revealed that the cause of the field defect was related to an eccentric inferiorly displaced pupil, secondary to trauma some years previously. Discussion Individual patient characteristics, including both ocular, as well as facial, need to be considered, when interpreting any visual field defect.
On the influence of extrinsic point defects on irradiation-induced point-defect distributions in silicon

International Nuclear Information System (INIS)

Vanhellemont, J.; Romano-Rodriguez, A.

1994-01-01

A semi-quantitative model describing the influence of interfaces and stress fields on {113}-defect generation in silicon during 1-MeV electron irradiation, is further developed to take into account also the role of extrinsic point defects. It is shown that the observed distribution of {113}-defects in high-flux electron-irradiated silicon and its dependence on irradiation temperature and dopant concentration can be understood by taking into account not only the influence of the surfaces and interfaces as sinks for intrinsic point defects but also the thermal stability of the bulk sinks for intrinsic point defects. In heavily doped silicon the bulk sinks are related with pairing reactions of the dopant atoms with the generated intrinsic point defects or related with enhanced recombination of vacancies and self-interstitials at extrinsic point defects. The obtained theoretical results are correlated with published experimental data on boron-and phosphorus-doped silicon and are illustrated with observations obtained by irradiating cross-section transmission electron microscopy samples of wafer with highly doped surface layers. (orig.)
Reconstruction of Facial Defect Using Deltopectoral Flap.

Science.gov (United States)

Aldelaimi, Tahrir N; Khalil, Afrah A

2015-11-01

Reconstruction of the head and neck is a challenge for otolarygology surgeons, maxillofacial surgeons as well as plastic surgeons. Defects caused by the resection and/or trauma should be closed with flaps which match in color, texture and hair bearing characteristics with the face. Deltopectoral flap is a one such flap from chest and neck skin mainly used to cover the facial defects. This study report a patient presenting with tragic Road Traffic Accident (RTA) admitted to maxillofacial surgery department at Ramadi Teaching Hospital, Anbar province, Iraq. An incision, medially based, was done and deltopectoral fascio-cutaneous flap was used for surgical exposure and closure of defects after RTA. There was no major complication. Good aesthetic and functional results were achieved. Deltopectoral flap is an excellent alternative for the reconstruction of head and neck. Harvesting and application of the flap is rapid and safe. Only a single incision is sufficient for dissection and flap elevation.
Defects of mutant DNMT1 are linked to a spectrum of neurological disorders

Science.gov (United States)

Baets, Jonathan; Duan, Xiaohui; Wu, Yanhong; Smith, Gordon; Seeley, William W.; Mademan, Inès; McGrath, Nicole M.; Beadell, Noah C.; Khoury, Julie; Botuyan, Maria-Victoria; Mer, Georges; Worrell, Gregory A.; Hojo, Kaori; DeLeon, Jessica; Laura, Matilde; Liu, Yo-Tsen; Senderek, Jan; Weis, Joachim; Van den Bergh, Peter; Merrill, Shana L.; Reilly, Mary M.; Houlden, Henry; Grossman, Murray; Scherer, Steven S.; De Jonghe, Peter; Dyck, Peter J.

2015-01-01

We report a broader than previously appreciated clinical spectrum for hereditary sensory and autonomic neuropathy type 1E (HSAN1E) and a potential pathogenic mechanism for DNA methyltransferase (DNMT1) mutations. The clinical presentations and genetic characteristics of nine newly identified HSAN1E kinships (45 affected subjects) were investigated. Five novel mutations of DNMT1 were discovered; p.C353F, p.T481P, p.P491L, p.Y524D and p.I531N, all within the target-sequence domain, and two mutations (p.T481P, p.P491L) arising de novo. Recently, HSAN1E has been suggested as an allelic disorder of autosomal dominant cerebellar ataxia, deafness and narcolepsy. Our results indicate that all the mutations causal for HSAN1E are located in the middle part or N-terminus end of the TS domain, whereas all the mutations causal for autosomal dominant cerebellar ataxia, deafness and narcolepsy are located in the C-terminus end of the TS domain. The impact of the seven causal mutations in this cohort was studied by cellular localization experiments. The binding efficiency of the mutant DNMT proteins at the replication foci and heterochromatin were evaluated. Phenotypic characterizations included electromyography, brain magnetic resonance and nuclear imaging, electroencephalography, sural nerve biopsies, sleep evaluation and neuropsychometric testing. The average survival of HSAN1E was 53.6 years. [standard deviation = 7.7, range 43–75 years], and mean onset age was 37.7 years. (standard deviation = 8.6, range 18–51 years). Expanded phenotypes include myoclonic seizures, auditory or visual hallucinations, and renal failure. Hypersomnia, rapid eye movement sleep disorder and/or narcolepsy were identified in 11 subjects. Global brain atrophy was found in 12 of 14 who had brain MRI. EEGs showed low frequency (delta waves) frontal-predominant abnormality in five of six patients. Marked variability in cognitive deficits was observed, but the majority of patients (89%) developed
Model for transport and reaction of defects and carriers within displacement cascades in gallium arsenide

International Nuclear Information System (INIS)

Wampler, William R.; Myers, Samuel M.

2015-01-01

A model is presented for recombination of charge carriers at evolving displacement damage in gallium arsenide, which includes clustering of the defects in atomic displacement cascades produced by neutron or ion irradiation. The carrier recombination model is based on an atomistic description of capture and emission of carriers by the defects with time evolution resulting from the migration and reaction of the defects. The physics and equations on which the model is based are presented, along with the details of the numerical methods used for their solution. The model uses a continuum description of diffusion, field-drift and reaction of carriers, and defects within a representative spherically symmetric cluster of defects. The initial radial defect profiles within the cluster were determined through pair-correlation-function analysis of the spatial distribution of defects obtained from the binary-collision code MARLOWE, using recoil energies for fission neutrons. Properties of the defects are discussed and values for their parameters are given, many of which were obtained from density functional theory. The model provides a basis for predicting the transient response of III-V heterojunction bipolar transistors to displacement damage from energetic particle irradiation
Stability and Electronic Properties of Hydrogenated Zigzag Carbon Nanotube Focused on Stone-Wales Defect

International Nuclear Information System (INIS)

Pan Li-Jun; Zhang Jie; Chen Wei-Guang; Tang Ya-Nan

2015-01-01

We present a first-principles study of the chemisorption of hydrogen on a Stone-Wales (SW) defective carbon nanotube (10,0). The investigated configurations include four configurations covering single defects and double defects. One hydrogen dimer adsorption is energetically favored on bonds shared by carbon heptagon-heptagon for configurations with the defect parallel to the tube axis compared with the carbon pentagon-hexagon sites for ones with a slanted defect. This different behavior is also demonstrated for hydrogen dimer chain adsorption, the favored site for the former ones is through the defect, which is the nearest neighbor site to defect for the latter ones. It is found that the energy band gaps of hydrogenated configurations may be enlarged or decreased by altering the adsorption site or defect position. The semiconductor-to-metal transition may occur for configurations with the defect or defects parallel to the tube axis due to low electronic localization. Our results highlight the interest of the interaction of multi-factor system by providing a detailed bond and position picture of a hydrogenated defective carbon nanotube (10,0). (paper)
Fructose-1,6-diphosphatase deficiency: Another enzyme defect which can present itself with the clinical features of “tyrosinosis”

NARCIS (Netherlands)

Bakker, H.D.; Bree, P.K. de; Ketting, D.; Sprang, F.J. van; Wadman, S.K.

1974-01-01

An infant with a picture of hereditary liver disease corresponding in many respects with so-called “tyrosinosis” is described. The primary defect appeared to be fructose-l,6-diphosphatase deficiency, which was not recognized during the patient's life. Many abnormalities of amino acid metabolism
The frequency spectrum crisis - Issues and answers

Science.gov (United States)

Armes, G. L.

The frequency spectrum represents a unique resource which can be overtaxed. In the present investigation, it is attempted to evalute the demand for satellite and microwave services. Dimensions of increased demand are discussed, taking into account developments related to the introduction of the personal computer, the activities of the computer and communications industries in preparation for the office of the future, and electronic publishing. Attention is given to common carrier spectrum congestion, common carrier microwave, satellite communications, teleports, international implications, satellite frequency bands, satellite spectrum implications, alternatives regarding the utilization of microwave frequency bands, U.S. Government spectrum utilization, and the impact at C-band.

A high signal-to-noise ratio composite quasar spectrum

International Nuclear Information System (INIS)

Francis, P.J.; Hewett, P.C.; Foltz, C.B.; Chaffee, F.H.; Weymann, R.J.

1991-01-01

A very high signal-to-noise ratio (S/N of about 400) composite spectrum of the rest-frame ultraviolet and optical region of high luminosity quasars is presented. The spectrum is derived from 718 individual spectra obtained as part of the Large Bright Quasar Survey. The moderate resolution, 4A or less, and high signal-to-noise ratio allow numerous weak emission features to be identified. Of particular note is the large equivalent-width of the Fe II emission in the rest-frame ultraviolet and the blue continuum slope of the composite. The primary aim of this paper is to provide a reference spectrum for use in line identifications, and a series of large-scale representations of the composite spectrum are shown. A measure of the standard deviation of the individual quasar spectra from the composite spectrum is also presented. 12 refs
Congenital Heart Defects and CCHD

Science.gov (United States)

... and more. Stony Point, NY 10980 Close X Home > Complications & Loss > Birth defects & other health conditions > Congenital heart defects and ... in congenital heart defects. You have a family history of congenital heart ... syndrome or VCF. After birth Your baby may be tested for CCHD as ...
Visual defects in a mouse model of fetal alcohol spectrum disorder.

Science.gov (United States)

Lantz, Crystal L; Pulimood, Nisha S; Rodrigues-Junior, Wandilson S; Chen, Ching-Kang; Manhaes, Alex C; Kalatsky, Valery A; Medina, Alexandre Esteves

2014-01-01

Alcohol consumption during pregnancy can lead to a multitude of neurological problems in offspring, varying from subtle behavioral changes to severe mental retardation. These alterations are collectively referred to as Fetal Alcohol Spectrum Disorders (FASD). Early alcohol exposure can strongly affect the visual system and children with FASD can exhibit an amblyopia-like pattern of visual acuity deficits even in the absence of optical and oculomotor disruption. Here, we test whether early alcohol exposure can lead to a disruption in visual acuity, using a model of FASD to mimic alcohol consumption in the last months of human gestation. To accomplish this, mice were exposed to ethanol (5 g/kg i.p.) or saline on postnatal days (P) 5, 7, and 9. Two to three weeks later we recorded visually evoked potentials to assess spatial frequency detection and contrast sensitivity, conducted electroretinography (ERG) to further assess visual function and imaged retinotopy using optical imaging of intrinsic signals. We observed that animals exposed to ethanol displayed spatial frequency acuity curves similar to controls. However, ethanol-treated animals showed a significant deficit in contrast sensitivity. Moreover, ERGs revealed a market decrease in both a- and b-waves amplitudes, and optical imaging suggest that both elevation and azimuth maps in ethanol-treated animals have a 10-20° greater map tilt compared to saline-treated controls. Overall, our findings suggest that binge alcohol drinking restricted to the last months of gestation in humans can lead to marked deficits in visual function.
Studies on defect detectability in banded stainless steel tubes

International Nuclear Information System (INIS)

Shyamsunder, M.T.; Rao, B.P.C.; Babu Rao, C.; Jayakumar, T.; Kalyanasundaram, P.; Baldev Raj

1996-01-01

During inspection of one batch of stainless steel cladding tubes, a few of the tubes gave rise to continuous large amplitude indications throughout the length of the tube. It was observed that the presence of any defects in such tubes would be impossible to detect, due to the poor signal-to-noise ratio. Detailed investigations regarding the surface profile of the tubes were carried out using a novel technique called the projected interferometry method revealed periodic diametral variations and the same were further confirmed by cross sectional profiling. The feasibility of detecting defects in such banded tubes, using eddy current testing were carried out on tubes with artificial defects. This paper discusses the use of three different eddy current methods and their relative performances for inspection. The specific advantages of the phased array eddy current testing method in unambiguous defect detection in situations similar to the one encountered during the present investigations are also discussed. (author)
Low-temperature electron irradiation induced defects in gallium arsenide: bulk and surface acoustic wave studies

International Nuclear Information System (INIS)

Brophy, M.J. Jr.

1985-01-01

Irradiation of GaAs with 2.25 to 2.5 MeV electrons at temperatures below 190 K produces two peaks in ultrasonic attenuation versus temperature. The defects responsible for both peaks have trigonal symmetry and were observed in n-type and semi-insulating GaAs with bulk and surface acoustic waves (SAW) respectively. Bulk waves at eight frequencies between 9 and 130 MHz and SAW at 73 and 145 MHz were used. The reorientation kinetics of both peaks follow the Arrhenius law. The annealing of both peaks was studied with isochronal and isothermal anneals in the temperature range 200 to 335 K. Peak I anneals with a spectrum of activation energies in the range 0.7-1.1 eV between 220 and 335 K. Peak II anneals with a single activation energy of about 1.1 eV above 300K. The different annealing characteristics indicate that these peaks represent two distinct defects. The annealing above 300 K has not been seen in electrical resistivity measurements, but was observed in earlier length change experiments. Irradiation of GaAs:Cr produces no Cr-radiation defect complexes. The attenuation peak associated with Cr 2+ decrease with electron dose, but starts to recover at 150 K
Priorities for autism spectrum disorder risk communication and ethics.

Science.gov (United States)

Yudell, Michael; Tabor, Holly K; Dawson, Geraldine; Rossi, John; Newschaffer, Craig

2013-11-01

Autism spectrum disorders are an issue of increasing public health significance. The incidence of autism spectrum disorders has been increasing in recent years, and they are associated with significant personal and financial impacts for affected persons and their families. In recent years, a large number of scientific studies have been undertaken, which investigate genetic and environmental risk factors for autism, with more studies underway. At present, much remains unknown regarding autism spectrum disorder risk factors, but the emerging picture of causation is in many cases complex, with multiple genes and gene-environment interactions being at play. The complexity and uncertainty surrounding autism spectrum disorder risk factors raise a number of questions regarding the ethical considerations that should be taken into account when undertaking autism spectrum disorder risk communication. At present, however, little has been written regarding autism spectrum disorder risk communication and ethics. This article summarizes the findings of a recent conference investigating ethical considerations and policy recommendations in autism spectrum disorder risk communication, which to the authors' knowledge is the first of its kind. Here, the authors discuss a number of issues, including uncertainty; comprehension; inadvertent harm; justice; and the appropriate roles of clinicians, scientists, and the media in autism spectrum disorder risk communication.
Defect types and room-temperature ferromagnetism in undoped rutile TiO2 single crystals

Science.gov (United States)

Li, Dong-Xiang; Qin, Xiu-Bo; Zheng, Li-Rong; Li, Yu-Xiao; Cao, Xing-Zhong; Li, Zhuo-Xin; Yang, Jing; Wang, Bao-Yi

2013-03-01

Room-temperature ferromagnetism has been experimentally observed in annealed rutile TiO2 single crystals when a magnetic field is applied parallel to the sample plane. By combining X-ray absorption near the edge structure spectrum and positron annihilation lifetime spectroscopy, Ti3+—VO defect complexes (or clusters) have been identified in annealed crystals at a high vacuum. We elucidate that the unpaired 3d electrons in Ti3+ ions provide the observed room-temperature ferromagnetism. In addition, excess oxygen ions in the TiO2 lattice could induce a number of Ti vacancies which obviously increase magnetic moments.
Defect types and room-temperature ferromagnetism in undoped rutile TiO2 single crystals

International Nuclear Information System (INIS)

Li Dong-Xiang; Cao Xing-Zhong; Li Zhuo-Xin; Yang Jing; Wang Bao-Yi; Qin Xiu-Bo; Zheng Li-Rong; Li Yu-Xiao

2013-01-01

Room-temperature ferromagnetism has been experimentally observed in annealed rutile TiO 2 single crystals when a magnetic field is applied parallel to the sample plane. By combining X-ray absorption near the edge structure spectrum and positron annihilation lifetime spectroscopy, Ti 3+ —V O defect complexes (or clusters) have been identified in annealed crystals at a high vacuum. We elucidate that the unpaired 3d electrons in Ti 3+ ions provide the observed room-temperature ferromagnetism. In addition, excess oxygen ions in the TiO 2 lattice could induce a number of Ti vacancies which obviously increase magnetic moments
Computer simulation of defect cluster

Energy Technology Data Exchange (ETDEWEB)

Kuramoto, Eiichi [Kyushu Univ., Kasuga, Fukuoka (Japan). Research Inst. for Applied Mechanics

1996-04-01

In order to elucidate individual element process of various defects and defect clusters of used materials under irradiation environments, interatomic potential with reliability was investigated. And for comparison with experimental results, it is often required to adopt the temperature effect and to investigate in details mechanism of one dimensional motion of micro conversion loop and so forth using the molecular dynamic (MD) method. Furthermore, temperature effect is also supposed for stable structure of defects and defect clusters, and many problems relating to alloy element are also remained. And, simulation on photon life at the defects and defect clusters thought to be important under comparison with equipment can also be supposed an improvement of effectiveness due to relation to theses products. In this paper, some topics in such flow was extracted to explain them. In particular, future important problems will be potential preparation of alloy, structure, dynamic behavior and limited temperature of intralattice atomic cluster. (G.K.)
Improvement of defect characterization in ultrasonic testing by adaptative learning network

International Nuclear Information System (INIS)

Bieth, M.; Adamonis, D.C.; Jusino, A.

1982-01-01

Numerous methods exist now for signal analysis in ultrasonic testing. These methods give more or less accurate information for defects characterization. In this paper is presented the development of a particular system based on a computer Signal processing: the Adaptative Learning Network (ALN) allowing the discrimination of defects in function of their nature. The ultrasonic signal is sampled and characterized by parameters amplitude-time and amplitude-frequency. The method was tested on stainless steel tubes welds showing fatigue cracks. The ALN model developed allows, under certain conditions, the discrimination of cracks from other defects [fr
Transcatheter closure of ventricular septal defect with Occlutech Duct Occluder.

Science.gov (United States)

Atik-Ugan, Sezen; Saltik, Irfan Levent

2018-04-01

Patent ductus arteriosus occluders are used for transcatheter closure of ventricular septal defects, as well as for closure of patent ductus arteriosus. The Occlutech Duct Occluder is a newly introduced device for transcatheter closure of patent ductus arteriosus. Here, we present a case in which the Occlutech Duct Occluder was successfully used on a patient for the closure of a perimembraneous ventricular septal defect.
Symmetry-forbidden intervalley scattering by atomic defects in monolayer transition-metal dichalcogenides

DEFF Research Database (Denmark)

Kaasbjerg, Kristen; Martiny, Johannes H. J.; Low, Tony

2017-01-01

protectionmechanism against intervalley scattering in monolayer TMDs. The predicteddefectdependent selection rules for intervalley scattering can be verified viaFourier transform scanning tunneling spectroscopy (FT-STS), and provide aunique identification of, e.g., atomic vacancy defects (M vs X). Our findingsare......Intervalley scattering by atomic defects in monolayer transition metaldichalcogenides (TDMs; MX2) presents a serious obstacle for applicationsexploiting their unique valley-contrasting properties. Here, we show that thesymmetry of the atomic defects can give rise to an unconventional...
Norwegian Pitched Roof Defects

Directory of Open Access Journals (Sweden)

Lars Gullbrekken

2016-06-01

Full Text Available The building constructions investigated in this work are pitched wooden roofs with exterior vertical drainpipes and wooden load-bearing system. The aim of this research is to further investigate the building defects of pitched wooden roofs and obtain an overview of typical roof defects. The work involves an analysis of the building defect archive from the research institute SINTEF Building and Infrastructure. The findings from the SINTEF archive show that moisture is a dominant exposure factor, especially in roof constructions. In pitched wooden roofs, more than half of the defects are caused by deficiencies in design, materials, or workmanship, where these deficiencies allow moisture from precipitation or indoor moisture into the structure. Hence, it is important to increase the focus on robust and durable solutions to avoid defects both from exterior and interior moisture sources in pitched wooden roofs. Proper design of interior ventilation and vapour retarders seem to be the main ways to control entry from interior moisture sources into attic and roof spaces.
Effect of defect length on rolling contact fatigue crack propagation in high strength steel

Directory of Open Access Journals (Sweden)

T. Makino

2015-10-01

Full Text Available The objective of the present paper is to clarify the effect of defect length in depth direction on rolling contact fatigue (RCF crack propagation in high strength steel. RCF test and synchrotron radiation micro computed tomography (SR micro CT imaging were conducted. In the case of the defect with the 15 m diameter, flaking life decreased with increasing defect length. In a comparison of the CT image and the SEM view, the shapes of defects and the locations of the horizontal cracks were almost the same respectively. The mechanism of RCF crack propagation was discussed by finite element (FE analysis. Defects led to higher tensile residual stress than that without defects in the region where the defect exists. The shear stress range at 0.1 mm in depth on the middle line of the defect and the range of mode II stress intensity factor at the bottom of a vertical crack increased with increasing defect length.
Point defect thermodynamics and diffusion in Fe3C: A first-principles study

International Nuclear Information System (INIS)

Chao Jiang; Uberuaga, B.P.; Srinivasan, S.G.

2008-01-01

The point defect structure of cementite (Fe 3 C) is investigated using a combination of the statistical mechanical Wagner-Schottky model and first-principles calculations within the generalized gradient approximation. Large 128-atom supercells are employed to obtain fully converged point defect formation energies. The present study unambiguously shows that carbon vacancies and octahedral carbon interstitials are the structural defects in C-depleted and C-rich cementite, respectively. The dominant thermal defects in C-depleted and stoichiometric cementite are found to be carbon Frenkel pairs. In C-rich cementite, however, the primary thermal excitations are strongly temperature-dependent: interbranch, Schottky and Frenkel defects dominate successively with increasing temperature. Using the nudged elastic band technique, the migration barriers of major point defects in cementite are also determined and compared with available experiments in the literature
Congenital platelet function defects

Science.gov (United States)

... pool disorder; Glanzmann's thrombasthenia; Bernard-Soulier syndrome; Platelet function defects - congenital ... Congenital platelet function defects are bleeding disorders that cause reduced platelet function. Most of the time, people with these disorders have ...
Diffusive, Structural, Optical, and Electrical Properties of Defects in Semiconductors

CERN Multimedia

Wagner, F E

2002-01-01

Electronic properties of semiconductors are extremely sensitive to defects and impurities that have localized electronic states with energy levels in the band gap of the semiconductor. Spectroscopic techniques like photoluminescence (PL), deep level transient spectroscopy (DLTS), or Hall effect, that are able to detect and characterize band gap states do not reveal direct information about their microscopic origin. To overcome this chemical "blindness", the present approach is to use radioactive isotopes as a tracer. Moreover, the recoil energies involved in $\\beta$ and $\\gamma$-decays can be used to create intrinsic isolated point defects (interstitials, vacancies) in a controlled way. A microscopic insight into the structure and the thermodynamic properties of complexes formed by interacting defects can be gained by detecting the hyperfine interaction between the nuclear moments of radioactive dopants and the electromagnetic fields present at the site of the radioactive nucleus. The understanding and the co...
Metallography of defects

International Nuclear Information System (INIS)

Borisova, E.A.; Bochvar, G.A.; Brun, M.Ya.

1980-01-01

Different types of defects of metallurgical, technological and exploitation origin in intermediate and final products of titanium alloys, are considered. The examples of metallic and nonmetallic inclusions, chemical homogeneity, different grains, bands, cracks, places of searing, porosity are given; methods of detecting the above defects are described. The methods of metallography, X-ray spectral analysis, measuring microhardness are used
Defects induced by helium implantation in SiC

International Nuclear Information System (INIS)

Oliviero, E.; Barbot, J.F.; Declemy, A.; Beaufort, M.F.; Oliviero, E.

2008-01-01

SiC is one of the considered materials for nuclear fuel conditioning and for the fabrication of some core structures in future nuclear generation reactors. For the development of this advance technology, a fundamental research on this material is of prime importance. In particular, the implantation/irradiation effects have to be understood and controlled. It is with this aim that the structural alterations induced by implantation/irradiation in SiC are studied by different experimental techniques as transmission electron microscopy, helium desorption, X-ray diffraction and Rutherford backscattering spectrometry. In this work, the different types of defects induced by helium implantation in SiC, point or primary defects (obtained at low energy (∼100 eV) until spread defects (obtained at higher energy (until ∼2 MeV)) are exposed. The amorphization/recrystallization and swelling phenomena are presented too. (O.M.)
Rabbit Calvarial Defect Model for Customized 3D-Printed Bone Grafts.

Science.gov (United States)

Lee, Kang-Gon; Lee, Kang-Sik; Kang, Yu-Jeoung; Hwang, Jong-Hyun; Lee, Se-Hwan; Park, Sang-Hyug; Park, Yongdoo; Cho, Young-Sam; Lee, Bu-Kyu

2018-05-01

Bone graft materials are commonly used to regenerate various bone defects, but their application is often limited because of the complex defect shape in various clinical conditions. Hence, customized bone grafts using three-dimensional (3D) printing techniques have been developed. However, conventional simple bone defect models are limited for evaluating the benefits and manufacturing accuracy of 3D-printed customized bone grafts. Thus, the aim of the present study was to develop a complex-shaped bone defect model. We designed an 8-shaped bony defect that consists of two simple circles attached to the rabbit calvarium. To determine the critical-sized defect (CSD) of the 8-shaped defects, 5.6- and 7-mm-diameter trephine burs were tested, and the 7-mm-diameter bur could successfully create a CSD, which was easily reproducible on the rabbit calvarium. The rate of new bone formation was 28.65% ± 8.63% at 16 weeks following creation of the defect. To confirm its efficacy for clinical use, the 8-shaped defect was created on a rabbit calvarium and 3D computed tomography (CT) was performed. A stereolithography file was produced using the CT data, and a 3D-printed polycaprolactone graft was fabricated. Using our 8-shaped defect model, we were able to modify the tolerances of the bone graft and calvarial defect to fabricate a more precise bone graft. Customized characteristics of the bone graft were then used to improve the accuracy of the bone graft. In addition, we confirmed the fitting ability of the 3D-printed graft during implantation of the graft. Our 8-shaped defect model on the rabbit calvarium using a 7.0-mm trephine bur may be a useful CSD model for evaluating 3D-printed graft materials.

Influence of cover defects on the attenuation of radon with earthen covers

International Nuclear Information System (INIS)

Kalkwarf, D.R.; Mayer, D.W.

1983-11-01

Experimental and theoretical evaluations of radon flux through laboratory-scale defective soil columns are presented together with a survey of literature on the formation and prevention of defects in soil covers. This report focuses on air-filled, centimeter-scale defects that are most probable in earthen covers for attenuating radon emission from uranium-mill tailings. Examples include shirnkage and erosion cracks, erosion piping, animal burrows and air channels formed by the biodegradation of vegetation roots. Calculations based on mathematical models indicate that collections of defects which could increase the radon flux from an earthen cover by a factor of two would be easily detected by visual inspection. However, these models ignore air-turbulence in the defect and drying of the soil around the defect. Laboratory measurements showed that turbulent diffusion of radon occurred through defects as narrow as 0.3 cm when subjected to a transverse air velocity of 1 to 6 miles per hour at the surface. Both turbulence and more-rapid drying of soil can accelerate radon flux to the cover surface. Consequently, recommended methods to inhibit defect formation should be applied. 29 references, 3 figures, 5 tables
Evaluation of Bending Strength of Carburized Gears Based on Inferential Identification of Principal Surface Layer Defects

Science.gov (United States)

Masuyama, Tomoya; Inoue, Katsumi; Yamanaka, Masashi; Kitamura, Kenichi; Saito, Tomoyuki

High load capacity of carburized gears originates mainly from the hardened layer and induced residual stress. On the other hand, surface decarburization, which causes a nonmartensitic layer, and inclusions such as oxides and segregation act as latent defects which considerably reduce fatigue strength. In this connection, the authors have proposed a formula of strength evaluation by separately quantifying defect influence. However, the principal defect which limits strength of gears with several different defects remains unclarified. This study presents a method of inferential identification of principal defects based on test results of carburized gears made of SCM420 clean steel, gears with both an artificial notch and nonmartensitic layer at the tooth fillet, and so forth. It clarifies practical uses of presented methods, and strength of carburized gears can be evaluated by focusing on principal defect size.
Lyophilized allogeneic bone grafts for cystic and discontinuity defects of the jaws

International Nuclear Information System (INIS)

Pill Hoon Choung; Eun Seok Kim

1999-01-01

Allogenic bone grafts have been used after various processing in each institute was made by lyophilized allogenic bone and used for maxillofacial reconstruction. Three types of lyophilized allogenic bone grafts as powder, chip and block form were performed to reconstruct the following defects: 1) maxillectomy, 2) mandiblectomy, 3) cystectomy, 4) cleft alveolus, 5) gap in orthognathic osteotomy, 6) peri-implant defect, 7) extraction socket, and 8) facial contouring. Above defects can be classified as cystic and discontinuity defects of the maxilia and the mandible. Because discontinuity defects have more difficult problems to reconstruct considering mechanical strength of the allogenic bone. We performed allogenic bone grafts on 50 cystic defects and 12 discontinuity defects of the jaws. Among them, 3 cases were removed due to infection, and the others had no complications. In reconstruction of cystic defects, the defects were filled with allogenic chip which were made from allogenic block bone at the surgery, which later were changed to host bone. Three cases of them showed tooth eruption through the allogenic bone grafting site, changing the eruption pathway, which was interrupted by the lesion. in reconstruction of discontinuity defects, usually allogenic bone has been used as a tray, in which PMCB or demineralized bone chips were filled. But we tried to reconstruct this discontinuity defect using allogeneic bone block without inside filling of PMCB different from tray type. We will present the results of allogenic bone grafts using cranial bone, costochondral graft, and the mandible
Methods of removal of defects arising at liquid etching of polycrystalline silicon

Directory of Open Access Journals (Sweden)

Ivanchykou A. E.

2008-02-01

Full Text Available The paper presents a model of generation of defects having the form of spots on the surface of the polycrystalline silicon during processing of semiconductor wafers with hydrofluoric acid based etchant, and a model of removal of such defects in chemical solutions. The authors investigate how the centrifuge speed during drying and the relief of structures, produced on the plate, effect the number of defects. It is shown that there is a possibility to remove defects by chemical treatment in the peroxide-ammonia solutions (PAS and also by sequence of chemical cleaning in Karo mixture, SiO2 etching and treatment in PAS.
Investigation of impurity defects in α-iron by molecular dynamics method

International Nuclear Information System (INIS)

Kevorkyan, Yu.R.

1986-01-01

Investigation of the configuration of impurity defects in α-iron by the molecular dynamics method is presented. The Jhonson model potential has been used to calculate the interaction of matrix atoms. The impurity-matrix atom interaction is described by the same form of the potential shifted along the axis of interatomic distances for a definite value. The correspondence between the shift value and change in the radius of the impurity defect is established on the basis of calculation of the relaxation volume. Possible configurations of the impurity - interstitial matrix atom complexes are obtained for the given model of the impurity defect, dimensional boundaries of possible transitions between different configurations are determined. Formation and bound energies, relaxation volumes of impurity defects are calculated
Study of reticular defects in V3Si (A15 structure)

International Nuclear Information System (INIS)

Ben Lamine, Abdelmottaleb

1980-01-01

The A15 crystal structure is that of superconductive compounds with high critical temperature. This research thesis aims at studying its possible reticular defects. In a first part, the author presents this structure and more particularly its crystallographic properties, reports the indexing of electronic diffraction diagrams (point diagrams and line diagrams of Kikuchi) in the case of V 3 Si. Then, after having described the sample preparation technique, the author reports the study of reticular defects by high voltage electronic microscopy on a raw V 3 Si crystal. The existence of a specific defect is highlighted and the crystallographic study of this defect is reported. It has been performed by means of computer-based simulation of contrast (TWODIS software). Results are then discussed
A simplified multisupport response spectrum method

Science.gov (United States)

Ye, Jihong; Zhang, Zhiqiang; Liu, Xianming

2012-03-01

A simplified multisupport response spectrum method is presented. The structural response is a sum of two components of a structure with a first natural period less than 2 s. The first component is the pseudostatic response caused by the inconsistent motions of the structural supports, and the second is the structural dynamic response to ground motion accelerations. This method is formally consistent with the classical response spectrum method, and the effects of multisupport excitation are considered for any modal response spectrum or modal superposition. If the seismic inputs at each support are the same, the support displacements caused by the pseudostatic response become rigid body displacements. The response spectrum in the case of multisupport excitations then reduces to that for uniform excitations. In other words, this multisupport response spectrum method is a modification and extension of the existing response spectrum method under uniform excitation. Moreover, most of the coherency coefficients in this formulation are simplified by approximating the ground motion excitation as white noise. The results indicate that this simplification can reduce the calculation time while maintaining accuracy. Furthermore, the internal forces obtained by the multisupport response spectrum method are compared with those produced by the traditional response spectrum method in two case studies of existing long-span structures. Because the effects of inconsistent support displacements are not considered in the traditional response spectrum method, the values of internal forces near the supports are underestimated. These regions are important potential failure points and deserve special attention in the seismic design of reticulated structures.
Annealing of radiation-induced defects in silicon in a simplified phenomenological model

International Nuclear Information System (INIS)

Lazanu, S.; Lazanu, I.

2001-01-01

The concentration of primary radiation-induced defects has been previously estimated considering both the explicit mechanisms of the primary interaction between the incoming particle and the nuclei of the semiconductor lattice, and the recoil energy partition between ionisation and displacements, in the frame of the Lindhard theory. The primary displacement defects are vacancies and interstitials that are essentially unstable in silicon. They interact via migration, recombination, annihilation or produce other defects. In the present work, the time evolution of the concentration of defects induced by pions in medium and high resistivity silicon for detectors is modelled, after irradiation. In some approximations, the differential equations representing the time evolution processes could be decoupled. The theoretical equations so obtained are solved analytically in some particular cases, with one free parameter, for a wide range of particle fluences and/or for a wide energy range of incident particles, for different temperatures; the corresponding stationary solutions are also presented
Resource management for energy and spectrum harvesting sensor networks

CERN Document Server

Zhang, Deyu; Zhou, Haibo; Shen, Xuemin (Sherman)

2017-01-01

This SpringerBrief offers a comprehensive review and in-depth discussion of the current research on resource management. The authors explain how to best utilize harvested energy and temporally available licensed spectrum. Throughout the brief, the primary focus is energy and spectrum harvesting sensor networks (ESHNs) including energy harvesting (EH)-powered spectrum sensing and dynamic spectrum access. To efficiently collect data through the available licensed spectrum, this brief examines the joint management of energy and spectrum. An EH-powered spectrum sensing and management scheme for Heterogeneous Spectrum Harvesting Sensor Networks (HSHSNs) is presented in this brief. The scheme dynamically schedules the data sensing and spectrum access of sensors in ESHSNs to optimize the network utility, while considering the stochastic nature of EH process, PU activities and channel conditions. This brief also provides useful insights for the practical resource management scheme design for ESHSNs and motivates a ne...
The solar spectrum from 1173 to 1324 A

Science.gov (United States)

Chipman, E.; Bruner, E. C., Jr.

1975-01-01

We present some of the results of a rocket flight which obtained a high-resolution stigmatic spectrum of the sun in the region 1173-1324 A. A list of 179 lines observed in this region is presented, with intensities, widths, and approximate excitation classes for each line. A reproduction and finding chart of the spectrum is included, along with discussion of some individual lines of special interest.
What the Spectrum of Microglial Functions Can Teach us About Fetal Alcohol Spectrum Disorder

Directory of Open Access Journals (Sweden)

Elissa L. Wong

2017-06-01

Full Text Available Alcohol exposure during gestation can lead to severe defects in brain development and lifelong physical, behavioral and learning deficits that are classified under the umbrella term fetal alcohol spectrum disorder (FASD. Sadly, FASD is diagnosed at an alarmingly high rate, affecting 2%–5% of live births in the United States, making it the most common non-heritable cause of mental disability. Currently, no standard therapies exist that are effective at battling FASD symptoms, highlighting a pressing need to better understand the underlying mechanisms by which alcohol affects the developing brain. While it is clear that sensory and cognitive deficits are driven by inappropriate development and remodeling of the neural circuits that mediate these processes, alcohol’s actions acutely and long-term on the brain milieu are diverse and complex. Microglia, the brain’s immune cells, have been thought to be a target for alcohol during development because of their exquisite ability to rapidly detect and respond to perturbations affecting the brain. Additionally, our view of these immune cells is rapidly changing, and recent studies have revealed a myriad of microglial physiological functions critical for normal brain development and long-term function. A clear and complete understanding of how microglial roles on this end of the spectrum may be altered in FASD is currently lacking. Such information could provide important insights toward novel therapeutic targets for FASD treatment. Here we review the literature that links microglia to neural circuit remodeling and provide a discussion of the current understanding of how developmental alcohol exposure affects microglial behavior in the context of developing brain circuits.
The reliability of ultrasonic inspection and the critical defect size

International Nuclear Information System (INIS)

Vasilchenko, G.S.; Bely, V.E.; Ovchinnikov, A.V.; Rivkin, E.Yu.

1991-01-01

The ability to detect fabrication and service-induced defects in the welded joints of components and pipelines in nuclear power stations by ultrasonic inspection when this is conducted by using standard instruments and procedures appears to be insufficient. This fact was confirmed by the research carried out in PISC program and other studies. In order to increase the accuracy of measurement and to obtain the additional information on the character of any defect in ultrasonic testing as well as the validity of applying nondestructive testing data to strength calculation, scientific researches have been promoted and carried out in the USSR in a program under the guidance of NPO CNIITMASH. The reliability of the ultrasonic control of welded joints and the ways and means for its improvement are discussed. The presentation of the parameters realized by the ultrasonic inspection of defects in the form of schema for the use in strength calculation is explained. The calculation of stress intensity factor, the estimation of critical defect size, and the estimation of acceptable defect size are reported. (K.I.)
A proposed defect tracking model for classifying the inserted defect reports to enhance software quality control.

Science.gov (United States)

Sultan, Torky; Khedr, Ayman E; Sayed, Mostafa

2013-01-01

NONE DECLARED Defect tracking systems play an important role in the software development organizations as they can store historical information about defects. There are many research in defect tracking models and systems to enhance their capabilities to be more specifically tracking, and were adopted with new technology. Furthermore, there are different studies in classifying bugs in a step by step method to have clear perception and applicable method in detecting such bugs. This paper shows a new proposed defect tracking model for the purpose of classifying the inserted defects reports in a step by step method for more enhancement of the software quality.
High resolution measurements supported by electronic structure calculations of two naphthalene derivatives: [1,5]- and [1,6]-naphthyridine—Estimation of the zero point inertial defect for planar polycyclic aromatic compounds

Energy Technology Data Exchange (ETDEWEB)

Gruet, S., E-mail: sebastien.gruet@synchrotron-soleil.fr, E-mail: manuel.goubet@univ-lille1.fr; Pirali, O. [AILES Beamline, Synchrotron SOLEIL, Saint-Aubin, 91192 Gif-sur-Yvette (France); Institut des Sciences Moléculaires d’Orsay, UMR 8214 CNRS – Université Paris Sud, 91405 Orsay Cedex (France); Goubet, M., E-mail: sebastien.gruet@synchrotron-soleil.fr, E-mail: manuel.goubet@univ-lille1.fr [Laboratoire de Physique des Lasers, Atomes et Molécules, UMR 8523 CNRS – Université Lille 1, 59655 Villeneuve d’Ascq Cedex (France)

2014-06-21

Polycyclic aromatic hydrocarbons (PAHs) molecules are suspected to be present in the interstellar medium and to participate to the broad and unresolved emissions features, the so-called unidentified infrared bands. In the laboratory, very few studies report the rotationally resolved structure of such important class of molecules. In the present work, both experimental and theoretical approaches provide the first accurate determination of the rotational energy levels of two diazanaphthalene: [1,5]- and [1,6]-naphthyridine. [1,6]-naphthyridine has been studied at high resolution, in the microwave (MW) region using a Fourier transform microwave spectrometer and in the far-infrared (FIR) region using synchrotron-based Fourier transform spectroscopy. The very accurate set of ground state (GS) constants deduced from the analysis of the MW spectrum allowed the analysis of the most intense modes in the FIR (ν{sub 38}-GS centered at about 483 cm{sup −1} and ν{sub 34}-GS centered at about 842 cm{sup −1}). In contrast with [1,6]-naphthyridine, pure rotation spectroscopy of [1,5]-naphthyridine cannot be performed for symmetry reasons so the combined study of the two intense FIR modes (ν{sub 22}-GS centered at about 166 cm{sup −1} and ν{sub 18}-GS centered at about 818 cm{sup −1}) provided the GS and the excited states constants. Although the analysis of the very dense rotational patterns for such large molecules remains very challenging, relatively accurate anharmonic density functional theory calculations appeared as a highly relevant supporting tool to the analysis for both molecules. In addition, the good agreement between the experimental and calculated infrared spectrum shows that the present theoretical approach should provide useful data for the astrophysical models. Moreover, inertial defects calculated in the GS (Δ{sub GS}) of both molecules exhibit slightly negative values as previously observed for planar species of this molecular family. We adjusted
Mesenteric defect with internal herniation in the pediatric emergency department: an unusual presentation of acute abdomen.

Science.gov (United States)

Hu, Mei-Hua; Huang, Go-Shine; Chen, Jeng-Chang; Wu, Chang-Teng

2014-04-01

Internal herniation is a rare cause of intestinal obstruction, especially in the emergency department. We report a child with acute abdomen resulting from transmesenteric internal herniation of the small bowel. Radiographic findings revealed gaseous distension of the bowel loops in the upper abdominal area with a paucity of gas in the lower abdomen. Operative finding showed gangrenous small bowel due to mesenteric defect with an internal herniation. The gangrenous bowel was resected and the patient was discharged with an uneventful outcome. We emphasize that early recognition of internal herniation warrants further evaluation and appropriate management. Copyright © 2012. Published by Elsevier B.V.
Implications of defect clusters formed in cascades on free defect generation and microstructural development

International Nuclear Information System (INIS)

Wiedersich, H.

1992-12-01

A large fraction of the defects produced by irradiation with energetic neutrons or heavy ions originates in cascades. Not only increased recombination of vacancy and interstitial defects but also significant clustering of like defects occur. Both processes reduce the number of point defects available for long range migration. Consequences of defect clustering in cascades will be discussed in a semi-quantitative form with the aid of calculations using a very simplified model: Quasi-steady-state distributions of immobile vacancy and/or interstitial clusters develop which, in turn, can become significant sinks for mobile defects, and, therefore reduce their lifetime. Although cluster sinks will cause segregation and, potentially, precipitation of second phases due to local changes of composition, the finite lifetime of clusters will not lead to lasting, local compositional changes. A transition from highly dense interstitial and vacancy cluster distributions to the void swelling regime occurs when the thermal evaporation of vacancies from small vacancy clusters becomes significant at higher temperatures. Unequal clustering of vacancies and interstitials leads to an imbalance of their fluxes of in the matrix and, hence, to unequal contributions to atom transport by interstitials and by vacancies even in the quasi-steady state approximation
Characterization of point defects in monolayer arsenene

Science.gov (United States)

Liang, Xiongyi; Ng, Siu-Pang; Ding, Ning; Wu, Chi-Man Lawrence

2018-06-01

Topological defects that are inevitably found in 2D materials can dramatically affect their properties. Using density functional theory (DFT) calculations and ab initio molecular dynamics (AIMD) method, the structural, thermodynamic, electronic and magnetic properties of six types of typical point defects in arsenene, i.e. the Stone-Wales defect, single and double vacancies and adatoms, were systemically studied. It was found that these defects were all more easily generated in arsenene with lower formation energies than those with graphene and silicene. Stone-Wales defects can be transformed from pristine arsenene by overcoming a barrier of 2.19 eV and single vacancy defects tend to coalesce into double vacancy defects by diffusion. However, a type of adatom defect does not exhibit kinetic stability at room temperature. In addition, SV defects and another type of adatom defect can remarkably affect the electronic and magnetic properties of arsenene, e.g. they can introduce localized states near the Fermi level, as well as a strongly local magnetic moment due to dangling bond and unpaired electron. Furthermore, the simulated scanning tunneling microscopy (STM) and Raman spectroscopy were computed and the types of point defects can be fully characterized by correlating the STM images and Raman spectra to the defective atomistic structures. The results provide significant insights to the effect of defects in arsenene for potential applications, as well as identifications of two helpful tools (STM and Raman spectroscopy) to distinguish the type of defects in arsenene for future experiments.
Multigrid and defect correction for the steady Navier-Stokes equations : application to aerodynamics

NARCIS (Netherlands)

Koren, B.

1991-01-01

Theoretical and expcrimental convergence results are presented for nonlinear multigrid and iterative defect correction applied to finite volume discretizations of the full, steady, 2D, compressible NavierStokes equations. lterative defect correction is introduced for circumventing the difficulty in
Dipole defects in beryl

International Nuclear Information System (INIS)

Holanda, B A; Cordeiro, R C; Blak, A R

2010-01-01

Dipole defects in gamma irradiated and thermally treated beryl (Be 3 Al 2 Si 6 O 18 ) samples have been studied using the Thermally Stimulated Depolarization Currents (TSDC) technique. TSDC experiments were performed in pink (morganite), green (emerald), blue (aquamarine) and colourless (goshenite) natural beryl. TSDC spectra present dipole peaks at 190K, 220K, 280K and 310K that change after gamma irradiation and thermal treatments. In morganite samples, for thermal treatments between 700K and 1100K, the 280K peak increase in intensity and the band at 220K disappears. An increase of the 280K peak and a decrease of the 190K peak were observed in the TSDC spectra of morganite after a gamma irradiation of 25kGy performed after the thermal treatments. In the case of emerald samples, thermal treatments enhanced the 280K peak and gamma irradiation partially destroyed this band. The goshenite TSDC spectra present only one band at 280K that is not affected either by thermal treatments or by gamma irradiation. All the observed peaks are of dipolar origin because the intensity of the bands is linearly dependent on the polarization field, behaviour of dipole defects. The systematic study, by means of TSDC measurements, of ionizing irradiation effects and thermal treatments in these crystals makes possible a better understanding of the role played by the impurities in beryl crystals.
Beating Birth Defects

Centers for Disease Control (CDC) Podcasts

Each year in the U.S., one in 33 babies is affected by a major birth defect. Women can greatly improve their chances of giving birth to a healthy baby by avoiding some of the risk factors for birth defects before and during pregnancy. In this podcast, Dr. Stuart Shapira discusses ways to improve the chances of giving birth to a healthy baby.

Some links on this page may take you to non-federal websites. Their policies may differ from this site.