WorldWideScience

Sample records for deep drawing process

  1. Predicting galling behaviour in deep drawing processes

    NARCIS (Netherlands)

    van der Linde, G.

    2011-01-01

    Deep drawing is a sheet metal forming process which is widely used in, for example, the automotive industry. With this process it is possible to form complex shaped parts of sheet metal and it is suitable for products that have to be produced in large numbers. The tools for this process are required

  2. Intelligent Shimming for Deep Drawing Processes

    DEFF Research Database (Denmark)

    Tommerup, Søren; Endelt, Benny Ørtoft; Danckert, Joachim

    2011-01-01

    cavities the blank-holder force distribution can be controlled during the punch stroke. By means of a sequence of numerical simulations abrasive wear is imposed to the deep drawing of a rectangular cup. The abrasive wear is modelled by changing the tool surface geometry using an algorithm based...... on the sliding energy density. As the tool surfaces are changed the material draw-in is significantly altered when using conventional open-loop control of the blank-holder force. A feed-back controller is presented which is capable of reducing the draw-in difference to a certain degree. Further a learning...

  3. Applying a punch with microridges in multistage deep drawing processes.

    Science.gov (United States)

    Lin, Bor-Tsuen; Yang, Cheng-Yu

    2016-01-01

    The developers of high aspect ratio components aim to minimize the processing stages in deep drawing processes. This study elucidates the application of microridge punches in multistage deep drawing processes. A microridge punch improves drawing performance, thereby reducing the number of stages required in deep forming processes. As an example, the original eight-stage deep forming process for a copper cylindrical cup with a high aspect ratio was analyzed by finite element simulation. Microridge punch designs were introduced in Stages 4 and 7 to replace the original punches. In addition, Stages 3 and 6 were eliminated. Finally, these changes were verified through experiments. The results showed that the microridge punches reduced the number of deep drawing stages yielding similar thickness difference percentages. Further, the numerical and experimental results demonstrated good consistency in the thickness distribution.

  4. Inverse Analysis to Formability Design in a Deep Drawing Process

    Science.gov (United States)

    Buranathiti, Thaweepat; Cao, Jian

    Deep drawing process is an important process adding values to flat sheet metals in many industries. An important concern in the design of a deep drawing process generally is formability. This paper aims to present the connection between formability and inverse analysis (IA), which is a systematical means for determining an optimal blank configuration for a deep drawing process. In this paper, IA is presented and explored by using a commercial finite element software package. A number of numerical studies on the effect of blank configurations to the quality of a part produced by a deep drawing process were conducted and analyzed. The quality of the drawing processes is numerically analyzed by using an explicit incremental nonlinear finite element code. The minimum distance between elemental principal strains and the strain-based forming limit curve (FLC) is defined as tearing margin to be the key performance index (KPI) implying the quality of the part. The initial blank configuration has shown that it plays a highly important role in the quality of the product via the deep drawing process. In addition, it is observed that if a blank configuration is not greatly deviated from the one obtained from IA, the blank can still result a good product. The strain history around the bottom fillet of the part is also observed. The paper concludes that IA is an important part of the design methodology for deep drawing processes.

  5. Friction modeling on multiple scales for Deep drawing processes

    NARCIS (Netherlands)

    Karupannasamy, Dinesh Kumar

    2013-01-01

    A deep drawing process is one of the widely used manufacturing techniques in the automotive industry because of its capability to produce complex shapes with sheet material, often performed using lubricants to ease the forming. Finite Element Methods (FEM) are popularly used at the design stage to

  6. NON-LINEAR FINITE ELEMENT MODELING OF DEEP DRAWING PROCESS

    Directory of Open Access Journals (Sweden)

    Hasan YILDIZ

    2004-03-01

    Full Text Available Deep drawing process is one of the main procedures used in different branches of industry. Finding numerical solutions for determination of the mechanical behaviour of this process will save time and money. In die surfaces, which have complex geometries, it is hard to determine the effects of parameters of sheet metal forming. Some of these parameters are wrinkling, tearing, and determination of the flow of the thin sheet metal in the die and thickness change. However, the most difficult one is determination of material properties during plastic deformation. In this study, the effects of all these parameters are analyzed before producing the dies. The explicit non-linear finite element method is chosen to be used in the analysis. The numerical results obtained for non-linear material and contact models are also compared with the experiments. A good agreement between the numerical and the experimental results is obtained. The results obtained for the models are given in detail.

  7. Computer Aided Process Planning for Non-Axisymmetric Deep Drawing Products

    Science.gov (United States)

    Park, Dong Hwan; Yarlagadda, Prasad K. D. V.

    2004-06-01

    In general, deep drawing products have various cross-section shapes such as cylindrical, rectangular and non-axisymmetric shapes. The application of the surface area calculation to non-axisymmetric deep drawing process has not been published yet. In this research, a surface area calculation for non-axisymmetric deep drawing products with elliptical shape was constructed for a design of blank shape of deep drawing products by using an AutoLISP function of AutoCAD software. A computer-aided process planning (CAPP) system for rotationally symmetric deep drawing products has been developed. However, the application of the system to non-axisymmetric components has not been reported yet. Thus, the CAPP system for non-axisymmetric deep drawing products with elliptical shape was constructed by using process sequence design. The system developed in this work consists of four modules. The first is recognition of shape module to recognize non-axisymmetric products. The second is a three-dimensional (3-D) modeling module to calculate the surface area for non-axisymmetric products. The third is a blank design module to create an oval-shaped blank with the identical surface area. The forth is a process planning module based on the production rules that play the best important role in an expert system for manufacturing. The production rules are generated and upgraded by interviewing field engineers. Especially, the drawing coefficient, the punch and die radii for elliptical shape products are considered as main design parameters. The suitability of this system was verified by applying to a real deep drawing product. This CAPP system constructed would be very useful to reduce lead-time for manufacturing and improve an accuracy of products.

  8. Improved process robustness by using closed loop control in deep drawing applications

    Science.gov (United States)

    Barthau, M.; Liewald, M.; Christian, Held

    2017-09-01

    The production of irregular shaped deep-drawing parts with high quality requirements, which are common in today’s automotive production, permanently challenges production processes. High requirements on lightweight construction of passenger car bodies following European regulations until 2020 have been massively increasing the use of high strength steels substantially for years and are also leading to bigger challenges in sheet metal part production. Of course, the more and more complex shapes of today’s car body shells also intensify the issue due to modern and future design criteria. The metal forming technology tries to meet these challenges by developing a highly sophisticated layout of deep drawing dies that consider part quality requirements, process robustness and controlled material flow during the deep or stretch drawing process phase. A new method for controlling material flow using a closed loop system was developed at the IFU Stuttgart. In contrast to previous approaches, this new method allows a control intervention during the deep-drawing stroke. The blank holder force around the outline of the drawn part is used as control variable. The closed loop is designed as trajectory follow up with feed forward control. The used command variable is the part-wall stress that is measured with a piezo-electric measuring pin. In this paper the used control loop will be described in detail. The experimental tool that was built for testing the new control approach is explained here with its features. A method for gaining the follow up trajectories from simulation will also be presented. Furthermore, experimental results considering the robustness of the deep drawing process and the gain in process performance with developed control loop will be shown. Finally, a new procedure for the industrial application of the new control method of deep drawing will be presented by using a new kind of active element to influence the local blank holder pressure onto part

  9. Validation of the FEA of a deep drawing process with additional force transmission

    Science.gov (United States)

    Behrens, B.-A.; Bouguecha, A.; Bonk, C.; Grbic, N.; Vucetic, M.

    2017-10-01

    In order to meet requirements by automotive industry like decreasing the CO2 emissions, which reflects in reducing vehicles mass in the car body, the chassis and the powertrain, the continuous innovation and further development of existing production processes are required. In sheet metal forming processes the process limits and components characteristics are defined through the process specific loads. While exceeding the load limits, a failure in the material occurs, which can be avoided by additional force transmission activated in the deep drawing process before the process limit is achieved. This contribution deals with experimental investigations of a forming process with additional force transmission regarding the extension of the process limits. Based on FEA a tool system is designed and developed by IFUM. For this purpose, the steel material HCT600 is analyzed numerically. Within the experimental investigations, the deep drawing processes, with and without the additional force transmission are carried out. Here, a comparison of the produced rectangle cups is done. Subsequently, the identical deep drawing processes are investigated numerically. Thereby, the values of the punch reaction force and displacement are estimated and compared with experimental results. Thus, the validation of material model is successfully carried out on process scale. For further quantitative verification of the FEA results the experimental determined geometry of the rectangular cup is measured optically with ATOS system of the company GOM mbH and digitally compared with external software Geomagic®QualifyTM. The goal of this paper is the verification of the transferability of the FEA model for a conventional deep drawing process to a deep drawing process with additional force transmission with a counter punch.

  10. Determination of Process Parameters in Multi-Stage Hydro-Mechanical Deep Drawing by FE Simulation

    Science.gov (United States)

    Kumar, D. Ravi; Manohar, M.

    2017-09-01

    In this work, analysis has been carried to simulate manufacturing of a near hemispherical bottom part with large depth by hydro-mechanical deep drawing with an aim to reduce the number of forming steps and to reduce the extent of thinning in the dome region. Inconel 718 has been considered as the material due to its importance in aerospace industry. It is a Ni-based super alloy and it is one of the most widely used of all super alloys primarily due to large-scale applications in aircraft engines. Using Finite Element Method (FEM), numerical simulations have been carried out for multi-stage hydro-mechanical deep drawing by using the same draw ratios and design parameters as in the case of conventional deep drawing in four stages. The results showed that the minimum thickness in the final part can be increased significantly when compared to conventional deep drawing. It has been found that the part could be deep drawn to the desired height (after trimming at the final stage) without any severe wrinkling. Blank holding force (BHF) and peak counter pressure have been found to have a strong influence on thinning in the component. Decreasing the coefficient of friction has marginally increased the minimum thickness in the final component. By increasing the draw ratio and optimizing BHF, counter pressure and die corner radius in the simulations, it has been found that it is possible to draw the final part in three stages. It has been found that thinning can be further reduced by decreasing the initial blank size without any reduction in the final height. This reduced the draw ratio at every stage and optimum combination of BHF and counter pressure have been found for the 3-stage process also.

  11. Process Simulation of Aluminium Sheet Metal Deep Drawing at Elevated Temperatures

    International Nuclear Information System (INIS)

    Winklhofer, Johannes; Trattnig, Gernot; Lind, Christoph; Sommitsch, Christof; Feuerhuber, Hannes

    2010-01-01

    Lightweight design is essential for an economic and environmentally friendly vehicle. Aluminium sheet metal is well known for its ability to improve the strength to weight ratio of lightweight structures. One disadvantage of aluminium is that it is less formable than steel. Therefore complex part geometries can only be realized by expensive multi-step production processes. One method for overcoming this disadvantage is deep drawing at elevated temperatures. In this way the formability of aluminium sheet metal can be improved significantly, and the number of necessary production steps can thereby be reduced. This paper introduces deep drawing of aluminium sheet metal at elevated temperatures, a corresponding simulation method, a characteristic process and its optimization. The temperature and strain rate dependent material properties of a 5xxx series alloy and their modelling are discussed. A three dimensional thermomechanically coupled finite element deep drawing simulation model and its validation are presented. Based on the validated simulation model an optimised process strategy regarding formability, time and cost is introduced.

  12. Development of a Hybrid Deep Drawing Process to Reduce Springback of AHSS

    Science.gov (United States)

    Boskovic, Vladimir; Sommitsch, Christoph; Kicin, Mustafa

    2017-09-01

    In future, the steel manufacturers will strive for the implementation of Advanced High Strength Steels (AHSS) in the automotive industry to reduce mass and improve structural performance. A key challenge is the definition of optimal and cost effective processes as well as solutions to introduce complex steel products in cold forming. However, the application of these AHSS often leads to formability problems such as springback. One promising approach in order to minimize springback is the relaxation of stress through the targeted heating of materials in the radius area after the deep drawing process. In this study, experiments are conducted on a Dual Phase (DP) and TWining Induced Plasticity (TWIP) steel for the process feasibility study. This work analyses the influence of various heat treatment temperatures on the springback reduction of deep drawn AHSS.

  13. Development of Hydro-Mechanical Deep Drawing

    DEFF Research Database (Denmark)

    Zhang, Shi-Hong; Danckert, Joachim

    1998-01-01

    The hydro-mechanical deep-drawing process is reviewed in this article. The process principles and features are introduced and the developments of the hydro-mechanical deep-drawing process in process performances, in theory and in numerical simulation are described. The applications are summarized....... Some other related hydraulic forming processes are also dealt with as a comparison....

  14. Validation of formability of laminated sheet metal for deep drawing process using GTN damage model

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Yongbin; Cha, Wan-gi; Kim, Naksoo [Department of Mechanical Engineering, Sogang University, 1 Sinsu-dong, Mapo-gu, Seoul, 121-742 (Korea, Republic of); Ko, Sangjin [Mold/die and forming technology team, Product prestige research lab, LG electronics, 222, LG-ro, Jinwi-myeon, Pyeongtaek-si, Gyeonggi-do, 451-713 (Korea, Republic of)

    2013-12-16

    In this study, we studied formability of PET/PVC laminated sheet metal which named VCM (Vinyl Coated Metal). VCM offers various patterns and good-looking metal steel used for appliances such as refrigerator and washing machine. But, this sheet has problems which are crack and peeling of film when the material is formed by deep drawing process. To predict the problems, we used finite element method and GTN (Gurson-Tvergaard-Needleman) damage model to represent damage of material. We divided the VCM into 3 layers (PET film, adhesive and steel added PVC) in finite element analysis model to express the crack and peeling phenomenon. The material properties of each layer are determined by reverse engineering based on tensile test result. Furthermore, we performed the simple rectangular deep drawing and simulated it. The simulation result shows good agreement with drawing experiment result in position, punch stroke of crack occurrence. Also, we studied the fracture mechanism of PET film on VCM by comparing the width direction strain of metal and PET film.

  15. Strain hardening of aluminium alloy 3004 in the deep drawing and ironing processes

    International Nuclear Information System (INIS)

    Courbon, J.; Duval, J.L.

    1993-01-01

    The evolution of material hardening resulting from the canmaking operations on aluminium beverage cans has been investigated. Tensile tests in cup walls revealed that deep drawing induced softening in the hoop direction and hardening in the meridian direction. This anisotropy is retained in the ironing operation. Changes in strain path on a heavily cold-rolled material probably cause such a complex behaviour. To determine hardening laws for deep drawing, simple shear tests were thus performed because of the strain path similarity. They allowed to determine hardening laws over larger strains than tension could reach and revealed a saturation of stress. Altogether they proved adapted to the understanding of deep drawing. (orig.)

  16. Equivalent drawbead performance in deep drawing simulations

    NARCIS (Netherlands)

    Meinders, Vincent T.; Geijselaers, Hubertus J.M.; Huetink, Han

    1999-01-01

    Drawbeads are applied in the deep drawing process to improve the control of the material flow during the forming operation. In simulations of the deep drawing process these drawbeads can be replaced by an equivalent drawbead model. In this paper the usage of an equivalent drawbead model in the

  17. Mechanical Behaviour of Conventional Materials at Experimental Conditions of Deep Drawing Technological Process

    Science.gov (United States)

    Nikolov, N.; Pashkouleva, D.; Kavardzhikov, V.

    2012-09-01

    The paper deals with experimental investigations on the mechanical behaviour of body-centred-cubic (BCC) and face-centred-cubic (FCC)-conventionally structured sheet metalic-metalic materials under stress-strain conditions of a deep drawing process determined by a coefficient close to the limiting one for Steel 08 and punch diameter of 50 mm. The mechanical characteristics of the investigated materials are identified by one-dimensional tension tests. The materials' responses, as results of identical loading conditions, are described by the change of blank sizes and characteristics of the forming processes. The chosen deformation path ensures obtaining a qualitative steel piece and leads to failures of aluminium and brass blanks. The reported results could be useful for investigations and predictions of the mechanical responses of such type metallic structures applying microscopic instrumented observations and numerical simulations.

  18. Metal flow of a tailor-welded blank in deep drawing process

    Science.gov (United States)

    Yan, Qi; Guo, Ruiquan

    2005-01-01

    Tailor welded blanks were used in the automotive industry to consolidate parts, reduce weight, and increase safety. In recent years, this technology was developing rapidly in China. In Chinese car models, tailor welded blanks had been applied in a lot of automobile parts such as rail, door inner, bumper, floor panel, etc. Concerns on the properties of tailor welded blanks had become more and more important for automobile industry. A lot of research had shown that the strength of the welded seam was higher than that of the base metal, such that the weld failure in the aspect of strength was not a critical issue. However, formability of tailor welded blanks in the stamping process was complex. Among them, the metal flow of tailor welded blanks in the stamping process must be investigated thoroughly in order to reduce the scrap rate during the stamping process in automobile factories. In this paper, the behavior of metal flow for tailor welded blanks made by the laser welding process with two types of different thickness combinations were studied in the deep drawing process. Simulations and experiment verification of the movement of weld line for tailor welded blanks were discussed in detail. Results showed that the control on the movement of welded seam during stamping process by taking some measures in the aspect of blank holder was effective.

  19. Investigate earing of TWIP steel sheet during deep-drawing process by using crystal plasticity constitutive model

    Directory of Open Access Journals (Sweden)

    Yang J.

    2015-01-01

    Full Text Available By combining the nonlinear finite element analysis techniques and crystal plasticity theory, the macroscopic mechanical behaviour of crystalline material, the texture evolution and earing-type characteristics are simulated accurately. In this work, a crystal plasticity model exhibiting deformation twinning is introduced based on crystal plasticity theory and saturation-type hardening laws for FCC metal Fe-22Mn-0.6C TWIP steel. Based on the CPFE model and parameters which have been determined for TWIP steel, a simplified finite element model for deep drawing is promoted by using crystal plasticity constitutive model. The earing characteristics in typical deep-drawing process are simulated well. Further, the drawing forces are calculated and compared to the experimental results from reference. Meanwhile, the impacts of drawing coefficient and initial texture on the earing characteristics are investigated for controlling the earing.

  20. Influence of asymmetrical drawing radius deviation in micro deep drawing

    Science.gov (United States)

    Heinrich, L.; Kobayashi, H.; Shimizu, T.; Yang, M.; Vollertsen, F.

    2017-09-01

    Nowadays, an increasing demand for small metal parts in electronic and automotive industries can be observed. Deep drawing is a well-suited technology for the production of such parts due to its excellent qualities for mass production. However, the downscaling of the forming process leads to new challenges in tooling and process design, such as high relative deviation of tool geometry or blank displacement compared to the macro scale. FEM simulation has been a widely-used tool to investigate the influence of symmetrical process deviations as for instance a global variance of the drawing radius. This study shows a different approach that allows to determine the impact of asymmetrical process deviations on micro deep drawing. In this particular case the impact of an asymmetrical drawing radius deviation and blank displacement on cup geometry deviation was investigated for different drawing ratios by experiments and FEM simulation. It was found that both variations result in an increasing cup height deviation. Nevertheless, with increasing drawing ratio a constant drawing radius deviation has an increasing impact, while blank displacement results in a decreasing offset of the cups geometry. This is explained by different mechanisms that result in an uneven cup geometry. While blank displacement leads to material surplus on one side of the cup, an unsymmetrical radius deviation on the other hand generates uneven stretching of the cups wall. This is intensified for higher drawing ratios. It can be concluded that the effect of uneven radius geometry proves to be of major importance for the production of accurately shaped micro cups and cannot be compensated by intentional blank displacement.

  1. Deep Drawing for high LDR by a new Hydro-rim Forming Process with Differential Temperature- Analysis and Experiments

    International Nuclear Information System (INIS)

    Simon, Y. Ben; Tirosh, J.; Rubinski, Ludmila

    2005-01-01

    The purpose of this study is to analyze and test a possible increase of the Limit Drawing Ratio (LDR) in Deep Drawing by Hydro-rim process (a certain subset of the classical Hydroforming) which includes the newly differential temperature effect. The idea is to facilitate the plastic flow by local heating along the flange and to cool the area where strength is needed. The suggested analysis is based on the dual bounds approach (upper and lower bounds simultaneously) using the highly versatile Johnson-Cook constitutive material model. The advantage of combined high hydraulic pressure (about 1000 bar) with relatively high blank temperature (with magnitude of about one third the melting temperature of the considered material) in the same operation is discussed. Emphasis is given to the rule of blank temperature difference (between the flange and the wall of the product) conjugate with optimal hydro rim pressure in increasing the limit drawing ratio of the products (Aluminum, Copper and various Steels)

  2. Iterative process control and sensor evaluation for deep drawing tools with integrated piezoelectric actuators

    Directory of Open Access Journals (Sweden)

    Bäume Tobias

    2016-01-01

    Full Text Available Due to the design-driven increase in complexity of forming car body parts, it becomes more difficult to ensure a stable forming process. Piezoelectric actuators can influence the material flow of stamping parts effectively. In this article the implementation of piezoelectric actuators in a large scale sheet metal forming tool of a car manufacturer is described. Additionally, it is shown that part quality can be assessed with the help of triangulation laser sensors, which are mounted on the blankholder. The resulting flange draw-in signals were processed and used to adopt the applying actuator force iteratively to reduce the occurrence of cracks. It was shown that process control helped to improve the quality of the stamping parts significantly.

  3. Design strategy for optimal iterative learning control applied on a deep drawing process

    DEFF Research Database (Denmark)

    Endelt, Benny Ørtoft

    2017-01-01

    Metal forming processes in general can be characterised as repetitive processes; this work will take advantage of this characteristic by developing an algorithm or control system which transfers process information from part to part, reducing the impact of repetitive uncertainties, e.g. a gradual...... changes in the material properties. The process is highly non-linear and the system plant is modelled using a non-linear finite element and the gain factors for the iterative learning controller is identified solving a non-linear optimal control problem. The optimal control problem is formulated as a non...

  4. Numerical Simulation of Hydro-mechanical Deep Drawing — A Study on the Effect of Process Parameters on Drawability and Thickness Variation

    Science.gov (United States)

    Singh, Swadesh Kumar; Kumar, D. Ravi

    2005-08-01

    Hydro-mechanical deep drawing is a process for producing cup shaped parts with the assistance of a pressurized fluid. In the present work, numerical simulation of the conventional and counter pressure deep drawing processes has been done with the help of a finite element method based software. Simulation results were analyzed to study the improvement in drawability by using hydro-mechanical processes. The thickness variations in the drawn cups were analyzed and also the effect of counter pressure and oil gap on the thickness distribution was studied. Numerical simulations were also used for the die design, which combines both drawing and ironing processes in a single operation. This modification in the die provides high drawability, facilitates smooth material flow, gives more uniform thickness distribution and corrects the shape distortion.

  5. Evaluation of deep drawing force under different friction conditions

    OpenAIRE

    Lăzărescu Lucian; Banabic Dorel

    2017-01-01

    The purpose of this study is to investigate the variation of the required punch load during the deep drawing process under different friction conditions. In this regards, several deep-drawing tests of cylindrical cups were conducted under four friction conditions at the tool–blank interface. The first case was the dry deep-drawing, considered as a reference friction condition, while in the other three cases hydraulic oil, lithium-based grease and animal fat were used as lubricants. For each f...

  6. The Creative Drawing process

    DEFF Research Database (Denmark)

    Flensborg, Ingelise

      The creative drawing process Associated Professor Ingelise Flensborg, PhD The Danish University school of Education, Aarhus University Tuborgvej 164 København NV   Why are children's drawings important for the development of cognitive structures and for their development in a visual society......'s. It is a pattern of actions as well as a pattern for action    In my doctoral thesis I discussed the connection between spatial orientation and visual representation (as a form of knowledge). I wanted to show the developmental possibilities within spatial cognition in art-education. I used the dynamic theory......, which is supposed to be our most basic cognitive structure. The body's interaction with the environment is decisive for children's spatial representations. In my theoretical and empirical investigations I found that this interaction creates the basic form of cognitive structures. The child...

  7. Evaluation of deep drawing force under different friction conditions

    Directory of Open Access Journals (Sweden)

    Lăzărescu Lucian

    2017-01-01

    Full Text Available The purpose of this study is to investigate the variation of the required punch load during the deep drawing process under different friction conditions. In this regards, several deep-drawing tests of cylindrical cups were conducted under four friction conditions at the tool–blank interface. The first case was the dry deep-drawing, considered as a reference friction condition, while in the other three cases hydraulic oil, lithium-based grease and animal fat were used as lubricants. For each friction case, three levels of blank holding force were adopted, namely 10, 20 and 25 kN. The finite element simulation of the deep-drawing process was used to generate a set of calibration curves. By overlapping the experimental load-stroke curves on the calibration curves, the friction coefficient was estimated for each friction case.

  8. Generative Processes: Thick Drawing

    Science.gov (United States)

    Wallick, Karl

    2012-01-01

    This article presents techniques and theories of generative drawing as a means for developing complex content in architecture design studios. Appending the word "generative" to drawing adds specificity to the most common representation tool and clarifies that such drawings are not singularly about communication or documentation but are…

  9. A quantitative lubricant test for deep drawing

    DEFF Research Database (Denmark)

    Olsson, David Dam; Bay, Niels; Andreasen, Jan L.

    2010-01-01

    A tribological test for deep drawing has been developed by which the performance of lubricants may be evaluated quantitatively measuring the maximum backstroke force on the punch owing to friction between tool and workpiece surface. The forming force is found not to give useful information...

  10. Deep Drawing Simulations With Different Polycrystalline Models

    Science.gov (United States)

    Duchêne, Laurent; de Montleau, Pierre; Bouvier, Salima; Habraken, Anne Marie

    2004-06-01

    The goal of this research is to study the anisotropic material behavior during forming processes, represented by both complex yield loci and kinematic-isotropic hardening models. A first part of this paper describes the main concepts of the `Stress-strain interpolation' model that has been implemented in the non-linear finite element code Lagamine. This model consists of a local description of the yield locus based on the texture of the material through the full constraints Taylor's model. The texture evolution due to plastic deformations is computed throughout the FEM simulations. This `local yield locus' approach was initially linked to the classical isotropic Swift hardening law. Recently, a more complex hardening model was implemented: the physically-based microstructural model of Teodosiu. It takes into account intergranular heterogeneity due to the evolution of dislocation structures, that affects isotropic and kinematic hardening. The influence of the hardening model is compared to the influence of the texture evolution thanks to deep drawing simulations.

  11. Step by step control of a deep drawing process with piezo-electric actuators in serial operation

    Directory of Open Access Journals (Sweden)

    Bäume Tobias

    2015-01-01

    Full Text Available Due to the design-driven increase in complexity of forming car body parts, it becomes more difficult to ensure a stable forming process. Piezoelectric actuators can influence the material flow of stamping parts effectively. In this article the implementation of piezoelectric actuators in a large scale sheet metal forming tool of a car manufacturer is described. Additionally, it is shown that part quality can be assessed with the help of triangulation laser sensors, which are mounted on the blankholder. The resulting flange draw-in signals were used to reduce the occurrence of wrinkling or the rate of cracking. It was shown that process control improved the quality of the stamping parts significantly.

  12. Experimental and numerical study of micro deep drawing

    Directory of Open Access Journals (Sweden)

    Luo Liang

    2015-01-01

    Full Text Available Micro forming is a key technology for an industrial miniaturisation trend, and micro deep drawing (MDD is a typical micro forming method. It has great advantages comparing to other micro manufacturing methods, such as net forming ability, mass production potential, high product quality and complex 3D metal products fabrication capacity. Meanwhile, it is facing difficulties, for example the so-called size effects, once scaled down to micro scale. To investigate and to solve the problems in MDD, a combined micro blanking-drawing machine is employed and an explicit-implicit micro deep drawing model with a voronoi blank model is developed. Through heat treatment different grain sizes can be obtained, which affect material's properties and, consequently, the drawing process parameters, as well as produced cups' quality. Further, a voronoi model can provide detailed material information in simulation, and numerical simulation results are in accordance with experimental results.

  13. Feedback control in deep drawing based on experimental datasets

    Science.gov (United States)

    Fischer, P.; Heingärtner, J.; Aichholzer, W.; Hortig, D.; Hora, P.

    2017-09-01

    In large-scale production of deep drawing parts, like in automotive industry, the effects of scattering material properties as well as warming of the tools have a significant impact on the drawing result. In the scope of the work, an approach is presented to minimize the influence of these effects on part quality by optically measuring the draw-in of each part and adjusting the settings of the press to keep the strain distribution, which is represented by the draw-in, inside a certain limit. For the design of the control algorithm, a design of experiments for in-line tests is used to quantify the influence of the blank holder force as well as the force distribution on the draw-in. The results of this experimental dataset are used to model the process behavior. Based on this model, a feedback control loop is designed. Finally, the performance of the control algorithm is validated in the production line.

  14. Warm Deep Drawing of Aluminium Sheet

    NARCIS (Netherlands)

    Bolt, P.J.; Werkhoven, R.J.; van den Boogaard, Antonius H.

    2003-01-01

    Aluminium sheet drawing processes can be improved by manipulating local flow behaviour by means of elevated temperatures and temperature gradients in the tooling. Forming tests showed that a substantial improvement is possible not only for 5xxx but also for 6xxx series alloys. Finite element method

  15. Hydro-mechanical deep drawing of rolled magnesium sheets

    Energy Technology Data Exchange (ETDEWEB)

    Bach, F.W.; Rodman, M.; Rossberg, A. [Hannover Univ., Garbsen (Germany). Inst. of Materials Science; Behrens, B.A.; Vogt, O. [Hannover Univ., Garbsen (DE). Inst. of Metal Forming and Metal Forming Machine Tools (IFUM)

    2005-12-01

    Magnesium sheets offer high specific properties which make them very attractive in modern light weight constructions. The main obstacles for a wider usage are their high production costs, the poor corrosion properties and the limited ductility. Until today, forming processes have to be conducted at temperatures well above T=220 C. In the first place, this is a cost factor. Moreover, technical aspects, such as grain growth or the limited use of lubrication speak against high temperatures. The first aim of the presented research work is to increase the ductility at lower temperatures by alloy modification and by an adapted rolling technology. The key factor to reach isotropic mechanical properties and increased limit drawing ratios in deep drawing tools, is to achieve fine, homogeneous microstructures. This can be done by cross rolling at moderate temperatures. The heat treatment has to be adapted accordingly. In a second stage, hydro-mechanical deep drawing experiments were carried out at elevated temperature. The results show that the forming behaviour of the tested Mg-alloys is considerably improved compared to conventional deep drawing. (orig.)

  16. Comparison of Conventional Deep Drawing, Hydromechanical Deep-Drawing and High Pressure Sheet Metal Forming by Numerical Experiments

    International Nuclear Information System (INIS)

    Oender, I. Erkan; Tekkaya, A. Erman

    2005-01-01

    Increasing use of new technologies in automotive and aircraft applications requires intensive research and developments on sheet metal forming processes. This study focuses on the assessment of sheet hydroforming, hydro-mechanical deep drawing and conventional deep-drawing processes by performing a systematic analysis by numerical simulations. Circular, elliptic, rectangular and square cross-section cups have been selected for the geometry spectrum. Within the range of each cross section, depth, drawing ratio and fillet radii have been altered systematically. St14 stainless steel has been used as the material throughout the study. The deformation behavior has been described by an elasto-plastic material model and all numerical simulations have been carried out by using a dynamic-explicit commercial finite element code. During the analyses each workpiece is produced by the three competing processes. The analyses results such as sheet thickness distribution, necking, forming of radii etc., are used for assessing the success of each forming process alternative. The analyses revealed that depending on the workpiece geometry and dimensional properties certain processes are preferable for obtaining satisfactory products. The process windows for each process have been established based on the analyzed parameters of the three different product geometries. This data is expected to be useful for selecting the appropriate production process for a given workpiece geometry

  17. Thin film system with integrated load and temperature sensors for the technical application in deep drawing process

    Science.gov (United States)

    Biehl, Saskia; Paetsch, Nancy; Meyer-Kornblum, Eike

    2017-05-01

    In these days industry 4.0 resounded throughout the land and means the fourth industrial revolution. The industry has to tackle the task of a flexible and customer-oriented production. Therefor the need of sensor systems for the measurement of temperature and load, the two most important categories in production, is rising. For getting the real specification during the production process the integration of sensor elements in high load regions of machinery is very important. Thus wear resistant thin film sensor systems directly applied onto the surface of plant components are in development. These multilayer systems combine excellent wear resistance with sensory behaviour. The sensor data will lead to a deeper process understanding, to optimization of simulation tools, to reduction of rejects and to an improvement of flexibility in production.

  18. Study on micro hydro-mechanical deep drawing using finite element method

    Directory of Open Access Journals (Sweden)

    Ma Xiaoguang

    2016-01-01

    Full Text Available A numerical model was established to investigate the micro hydro-mechanical deep drawing process of austenitic stainless steel 304 foil (0.05 mm thickness. Due to the miniaturisation of the specimen size, the effect of grain size, gap distance and radial pressure during drawing process could be prominent. The results indicate that the appropriate radial pressure and gap distance could improve the limit drawing ratio (LDR of manufactured cylindrical cups by reducing the friction resistance. The maximum LDR obtained in the present work reaches 3.2, which is much higher than that obtained by conventional deep drawing process.

  19. Study of wear performance of deep drawing tooling

    Science.gov (United States)

    Naranje, Vishal G.; Karthikeyan, Ram; Nair, Vipin

    2017-09-01

    One of the most common challenges for many of the mechanical engineers and also in the field of materials science is the issue of occurrences of wear of the material parts which is used in certain applications that involves such surface interactions. In this paper, wear behaviour of particular grade High Carbon High Chromium Steel and many most famously D2, H13, O1 known as the Viking steel has been studied, evaluated and analyzed under certain processing parameters such as speed, load, track diameter and time required for deep drawing process to know it’s the wear rate and coefficient of friction. Also, the significance of the processing parameters which is used for wear testing analysis is also examined.

  20. Sunspot drawings handwritten character recognition method based on deep learning

    Science.gov (United States)

    Zheng, Sheng; Zeng, Xiangyun; Lin, Ganghua; Zhao, Cui; Feng, Yongli; Tao, Jinping; Zhu, Daoyuan; Xiong, Li

    2016-05-01

    High accuracy scanned sunspot drawings handwritten characters recognition is an issue of critical importance to analyze sunspots movement and store them in the database. This paper presents a robust deep learning method for scanned sunspot drawings handwritten characters recognition. The convolution neural network (CNN) is one algorithm of deep learning which is truly successful in training of multi-layer network structure. CNN is used to train recognition model of handwritten character images which are extracted from the original sunspot drawings. We demonstrate the advantages of the proposed method on sunspot drawings provided by Chinese Academy Yunnan Observatory and obtain the daily full-disc sunspot numbers and sunspot areas from the sunspot drawings. The experimental results show that the proposed method achieves a high recognition accurate rate.

  1. Deep drawing simulation of Tailored Blanks

    NARCIS (Netherlands)

    van den Berg, Albert; Meinders, Vincent T.; Stokman, B.

    1998-01-01

    Tailored blanks are increasingly used in the automotive industry. A tailored blank consists of different metal parts, which are joined by a welding process. These metal parts usually have different material properties. Hence, the main advantage of using a tailored blank is to provide the right

  2. Aspects of Finite Element Simulation of Axi-Symmetric Hydromechanical Deep Drawing

    DEFF Research Database (Denmark)

    Jensen, Morten Rikard; Olovsson, Lars; Danckert, Joachim

    1999-01-01

    A new approach for the Finite Element modelling of the hydromechanical deep drawing process is evaluated. In the model a Finite Difference approximation of Reynold’s equation is solved for the fluid flow between the blank and the draw die in the flange region. The approach is implemented...... as a contact algorithm in an explicit Finite Element code, Exhale2D. The developed model is verified against experiments and good agreement is obtained. It is concluded that the developed model is a promising approach for simulating the hydromechanical deep drawing process using the Finite Element Method....

  3. Experimental verification of a deep drawing tool system for adaptive blank holder pressure distribution

    DEFF Research Database (Denmark)

    Tommerup, Søren; Endelt, Benny Ørtoft

    2012-01-01

    In deep drawing, the strain path in the blank during the forming process can be significantly affected by application of temporal and spatial variation of the blank holder force. In this study, an active tool system capable of controlling the distribution of the blank holder force is presented...... which can be integrated into existing stacked deep drawing tools without need for modification of the press. A working system is presented consisting of a controller, designated volume displacement cavity pressure supply units and a shimming plate. It is applied to the deep drawing of a rectangular...... to the conventional shimming method using paper or metal shims between the tool plates. The tool system’s ability to influence the material flow is investigated by performing a series of deep drawing experiments. Eight different cavity pressure schemes are applied during the punch stroke and the scheme’s effects...

  4. Development of a quantitative lubricant test for deep drawing

    DEFF Research Database (Denmark)

    Olsson, David Dam; Bay, Niels; Andreasen, Jan Lasson

    2004-01-01

    A tribological test for deep drawing has been developed by which the performance of lubricants may be evaluated quantitatively measuring the maximum backstroke force on the punch due to sliding friction between tool and work piece surface. The forming force is found not to give useful information...

  5. Finite Element Analysis and Optimization for the Multi-stage Deep Drawing of Molybdenum Sheet

    International Nuclear Information System (INIS)

    Kim, Heung-Kyu; Hong, Seok Kwan; Kang, Jeong Jin; Heo, Young-moo; Lee, Jong-Kil; Jeon, Byung-Hee

    2005-01-01

    Molybdenum, a bcc refractory metal with a melting point of about 2600 deg. C, has a high heat and electrical conductivity. In addition, it remains strong mechanically at high temperatures as well as at low temperatures. Therefore it is a technologically very important material for the applications operating at high temperatures. However, a multi-stage process is required due to the low drawability for making a deep drawn part from the molybdenum sheet. In this study, a multi-stage deep drawing process for a molybdenum circular cup was designed by combining the drawing with the ironing, which was effective for the low drawability materials. A parametric study by FE analysis for the multi-stage deep drawing was conducted for evaluation of the design variables effect. Based on the FE analysis result, the multi-stage deep drawing process was parameterized by the design variables, and an optimum process design was obtained by the process optimization based on the FE simulation at each stage

  6. Study the effect of elevated dies temperature on aluminium and steel round deep drawing

    International Nuclear Information System (INIS)

    Lean, Yeong Wei; Azuddin, M.

    2016-01-01

    Round deep drawing operation can only be realized by expensive multi-step production processes. To reduce the cost of processes while expecting an acceptable result, round deep drawing can be done at elevated temperature. There are 3 common problems which are fracture, wrinkling and earing of deep drawing a round cup. The main objective is to investigate the effect of dies temperature on aluminium and steel round deep drawing; with a sub-objective of eliminate fracture and reducing wrinkling effect. Experimental method is conducted with 3 different techniques on heating the die. The techniques are heating both upper and lower dies, heating only the upper dies, and heating only the lower dies. 4 different temperatures has been chosen throughout the experiment. The experimental result then will be compared with finite element analysis software. There is a positive result from steel material on heating both upper and lower dies, where the simulation result shows comparable as experimental result. Heating both upper and lower dies will be the best among 3 types of heating techniques. (paper)

  7. Deformation Behavior of Reverse Deep Drawing of 5A06 Aluminum Alloy Plate

    Directory of Open Access Journals (Sweden)

    ZHANG Zhi-chao

    2017-09-01

    Full Text Available The limit drawing ratio is influenced by the bending and unbending effect during reverse deep drawing of plate. The 5A06 aluminum alloy plate widely applied in aerospace industry was used, and the reverse deep drawing of the 4.5mm thick plate was investigated experimentally and numerically. The stress and strain distributions of plate were analyzed, the deformation behaviour was discussed for three types of cross section of die during the reverse deep drawing process; moreover, the changing rule of strain paths with the die profile was also discussed. Results show that a maximum radial stress is induced by the bending effect at the transient region between the inside die radius and straight wall, where a radial stress and strain gradient along the thickness direction appears and the fracture is easy to occur. For the semi-circle profiled die structure, the limited punch stroke is 203mm which is increased by 40% than that for the die with a planar profile section. The semi-circle profiled die structure can reduce the bending effect, effectively reduce the stress gradient and the maximum stress value in the transient region, and is helpful to improve the limit drawing ratio of the 5A06 aluminum alloy plate.

  8. Deep subsurface microbial processes

    Science.gov (United States)

    Lovley, D.R.; Chapelle, F.H.

    1995-01-01

    Information on the microbiology of the deep subsurface is necessary in order to understand the factors controlling the rate and extent of the microbially catalyzed redox reactions that influence the geophysical properties of these environments. Furthermore, there is an increasing threat that deep aquifers, an important drinking water resource, may be contaminated by man's activities, and there is a need to predict the extent to which microbial activity may remediate such contamination. Metabolically active microorganisms can be recovered from a diversity of deep subsurface environments. The available evidence suggests that these microorganisms are responsible for catalyzing the oxidation of organic matter coupled to a variety of electron acceptors just as microorganisms do in surface sediments, but at much slower rates. The technical difficulties in aseptically sampling deep subsurface sediments and the fact that microbial processes in laboratory incubations of deep subsurface material often do not mimic in situ processes frequently necessitate that microbial activity in the deep subsurface be inferred through nonmicrobiological analyses of ground water. These approaches include measurements of dissolved H2, which can predict the predominant microbially catalyzed redox reactions in aquifers, as well as geochemical and groundwater flow modeling, which can be used to estimate the rates of microbial processes. Microorganisms recovered from the deep subsurface have the potential to affect the fate of toxic organics and inorganic contaminants in groundwater. Microbial activity also greatly influences 1 the chemistry of many pristine groundwaters and contributes to such phenomena as porosity development in carbonate aquifers, accumulation of undesirably high concentrations of dissolved iron, and production of methane and hydrogen sulfide. Although the last decade has seen a dramatic increase in interest in deep subsurface microbiology, in comparison with the study of

  9. Modelling mixed lubrication for deep drawing processes

    NARCIS (Netherlands)

    Karupannasamy, D.K.; Hol, J.; de Rooij, Matthias B.; Meinders, Vincent T.; Schipper, Dirk J.

    2012-01-01

    In Finite Element (FE) simulations of sheet metal forming (SMF), the coefficient of friction is generally expressed as a constant Coulomb friction. However in reality, the coefficient of friction at the local contact spots varies with the varying operational, deformation and contact conditions.

  10. Formability of paperboard during deep-drawing with local steam application

    Science.gov (United States)

    Franke, Wilken; Stein, Philipp; Dörsam, Sven; Groche, Peter

    2018-05-01

    The use of paperboard can significantly improve the environmental compatibility of everyday products such as packages. Nevertheless, most packages are currently made of plastics, since the three-dimensional shaping of paperboard is possible only to a limited extent. In order to increase the forming possibilities, deep drawing of cardboard has been intensively investigated for more than a decade. An improvement with regard to increased forming limits has been achieved by heating of the tool parts, which leads to a softening of paperboard constituents such as lignin. A further approach is the moistening of the samples, whereby the hydrogen bonds between the fibers are weakened and as a result an increase of the formability. It is expected that a combination of both parameter approaches will result in a significant increase in the forming capacity and in the shape accuracy. For this reason, a new tool concept is introduced within the scope of this work which makes it possible to moisten samples during the deep drawing process by means of steam supply. The conducted investigations show that spring-back in the preferred fiber direction can be reduced by 38 %. Orthogonal to the preferred fiber direction a reduction of spring back of up to 79 % is determined, which corresponds to a perfect shape. Moreover, it was determined that the steam duration and the initial moisture content have an influence on the final shape. In addition to the increased dimensional accuracy, an optimized wrinkle compression compared to conventional deep drawing is found. According to the results, it can be summarized that a steam application in the deep drawing of paperboard significantly improves the part quality.

  11. Deep learning evaluation using deep linguistic processing

    OpenAIRE

    Kuhnle, Alexander; Copestake, Ann

    2017-01-01

    We discuss problems with the standard approaches to evaluation for tasks like visual question answering, and argue that artificial data can be used to address these as a complement to current practice. We demonstrate that with the help of existing 'deep' linguistic processing technology we are able to create challenging abstract datasets, which enable us to investigate the language understanding abilities of multimodal deep learning models in detail, as compared to a single performance value ...

  12. Deep Drawing Behavior of CoCrFeMnNi High-Entropy Alloys

    Science.gov (United States)

    Bae, Jae Wung; Moon, Jongun; Jang, Min Ji; Ahn, Dong-Hyun; Joo, Soo-Hyun; Jung, Jaimyun; Yim, Dami; Kim, Hyoung Seop

    2017-09-01

    Herein, the deep drawability and deep drawing behavior of an equiatomic CoCrFeMnNi HEA and its microstructure and texture evolution are first studied for future applications. The CoCrFeMnNi HEA is successfully drawn to a limit drawing ratio (LDR) of 2.14, while the planar anisotropy of the drawn cup specimen is negligible. The moderate combination of strain hardening exponent and strain rate sensitivity and the formation of deformation twins in the edge region play important roles in successful deep drawing. In the meanwhile, the texture evolution of CoCrFeMnNi HEA has similarities with conventional fcc metals.

  13. Investigation of holder pressure and size effects in micro deep drawing of rectangular work pieces driven by piezoelectric actuator.

    Science.gov (United States)

    Aminzahed, Iman; Mashhadi, Mahmoud Mosavi; Sereshk, Mohammad Reza Vaziri

    2017-02-01

    Micro forming is a manufacturing process to fabricate micro parts with high quality and a cost effective manner. Deep drawing could be a favorable method for production of complicated parts in macro and micro sizes. In this paper piezoelectric actuator is used as a novel approach in the field of micro manufacturing. Also, in current work, investigations are conducted with four rectangular punches and blanks with various thicknesses. Blank holder pressure effects on thickness distributions, punch force, and springback are studied. According to the results of this work, increasing of blank holder pressure in scaled deep drawing, in contrast to thickness of drawn part, leads to decrease in the punch forces and springback. Furthermore, it is shown that in micro deep drawing, the effects of holder pressure on mentioned parameters can be ignored. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Micro-hydromechanical deep drawing of metal cups with hydraulic pressure effects

    Science.gov (United States)

    Luo, Liang; Jiang, Zhengyi; Wei, Dongbin; Wang, Xiaogang; Zhou, Cunlong; Huang, Qingxue

    2018-03-01

    Micro-metal products have recently enjoyed high demand. In addition, metal microforming has drawn increasing attention due to its net-forming capability, batch manufacturing potential, high product quality, and relatively low equipment cost. Micro-hydromechanical deep drawing (MHDD), a typical microforming method, has been developed to take advantage of hydraulic force. With reduced dimensions, the hydraulic pressure development changes; accordingly, the lubrication condition changes from the macroscale to the microscale. A Voronoi-based finite element model is proposed in this paper to consider the change in lubrication in MHDD according to open and closed lubricant pocket theory. Simulation results agree with experimental results concerning drawing force. Changes in friction significantly affect the drawing process and the drawn cups. Moreover, defined wrinkle indexes have been shown to have a complex relationship with hydraulic pressure. High hydraulic pressure can increase the maximum drawing ratio (drawn cup height), whereas the surface finish represented by the wear is not linearly dependent on the hydraulic pressure due to the wrinkles.

  15. Investigation into the factors that influence inverse bulging effect during sheet hydro-mechanical deep drawing

    Directory of Open Access Journals (Sweden)

    Lang Lihui

    2015-01-01

    Full Text Available The factors that influence inverse bulging effect during sheet hydro-mechanical deep drawing are especially researched in this paper. According to the different inverse bulging process, two modes can be singled: the initial inverse bulging (IIB and the local inverse bulging (LIB. IIB includes two parameters: inverse bulging height ratio (HIb/t and inverse bulging pressure ratio (PIb/t. LIB is influenced by IIB and has a direct relationship with liquid chamber pressure in the forming process. The optimal inverse bulging parameters of hemispherical bottom cylindrical part and flat bottom cylindrical part are obtained by numerical simulation. Process parameters including the clearance between the punch and the blank holder and the blank holder entrance radius that have a large influence on inverse bulging effect are optimized, so as to make inverse bulging effect behave better in hydroforming process. Finally, the accuracy of the numerical simulation results was verified by experiments.

  16. Waste Receiving and Processing Facility (WRAP) Drawing List

    International Nuclear Information System (INIS)

    WEIDERT, J.R.

    1999-01-01

    This supporting document delineates the process of identification, categorization, and/or classification of the WRAP facility drawings used to support facility operations and maintenance. This document provides a listing of those essential or safety related drawings which have been identified to date. All other WRAP facility drawings have been classified as general

  17. Superplasticity and Micro-arrayed Deep-Drawing Behavior of Ni-Co/GO Nanocomposite

    Science.gov (United States)

    Wang, Guofeng; Zhao, Shanshan; Li, You; Yang, Chao; Liu, Siyu

    2017-10-01

    In this article, Ni-Co/GO nanocomposite was fabricated by AC pulse electrodeposition method. The room temperature strength tests and the superplasticity of the nanocomposite were investigated by the tensile tests. A 5 × 5 micro-arrayed deep-drawing die was designed to explore the feasibility of micro-forming. The as-deposited material has a narrow grain size distribution with a mean grain size of 50 nm. The addition of GO as a reinforcing phase can effectively enhance the room temperature tensile strength of the nanocomposite, but reduce the plasticity. When adding GO to the plating bath, a maximum elongation of 467% was observed for the specimen with a GO content of 0.01 g/L at 773 K and a strain rate of 1.67 × 10-3 s-1 by tensile tests. Micro-arrayed deep-drawing tests were subsequently performed with male die diameter of 0.58 mm and female die diameter of 0.8 mm. The experimental relative drawing height values were measured and compared with the deep-drawing parts without GO additive. It is found that the micro-arrayed deep-drawing with rigid male die at high temperature was feasible and forming parts with good shape could be got. The thickness distribution analysis of the deep-drawing parts showed that wall thickness changed ranging from 53 to 95 μm, and the thickness reduction at the punch fillet is the most obvious.

  18. Numerical and Experimental Study on Manufacture of a Novel High-Capacity Engine Oil Pan Subjected to Hydro-Mechanical Deep Drawing

    Science.gov (United States)

    Chen, D. Y.; Xu, Y.; Zhang, S. H.; El-Aty, A. Abd; Ma, Y.

    2017-09-01

    The oil pan is equipped at the bottom of engine crankcase of the automobile to prevent impurity and collect the lubrication oil from the surfaces of the engine which is helpful for heat dissipation and oxidation prevention. The present study aims at manufacturing a novel high-capacity engine oil pan, which is considered as a complex shaped component with features of thin wall, large size and asymmetric deep cavity through both numerical and experimental methods. The result indicated that it is difficult to form the current part through the common deep drawing process. Accordingly, the hydro-mechanical deep drawing technology was conducted, which consisted of two steps, previous local drawing and the final integral deep drawing with hydraulic pressure. The finite element analysis (FEA) was carried out to investigate the influence of initial blank dimension and the key process parameters such as loading path, draw-bead force and fillet radius on the formability of the sheet blank. Compared with the common deep drawing, the limit drawing ratio by hydro-mechanical deep drawing can be increased from 2.34 to 2.77, while the reduction in blank wall thickness can be controlled in the range of 28%. The formability is greatly improved without any defects such as crack and wrinkle by means of parameters optimisation. The results gained from simulation keep a reasonable agreement with that obtained from experiment trials.

  19. Drawing as Instrument, Drawings as Evidence: Capturing Mental Processes with Pencil and Paper.

    Science.gov (United States)

    Puglionesi, Alicia

    2016-07-01

    Researchers in the mind sciences often look to the production and analysis of drawings to reveal the mental processes of their subjects. This essay presents three episodes that trace the emergence of drawing as an instrumental practice in the study of the mind. Between 1880 and 1930, drawings gained currency as a form of scientific evidence - as stable, reproducible signals from a hidden interior. I begin with the use of drawings as data in the child study movement, move to the telepathic transmission of drawings in psychical research and conclude with the development of drawing as an experimental and diagnostic tool for studying neurological impairment. Despite significant shifts in the theoretical and disciplinary organisation of the mind sciences in the early twentieth century, researchers attempted to stabilise the use of subject-generated drawings as evidence by controlling the contexts in which drawings were produced and reproduced, and crafting subjects whose interiority could be effectively circumscribed. While movements such as psychoanalysis and art therapy would embrace the narrative interpretation of patient art, neuropsychology continued to utilise drawings as material traces of cognitive functions.

  20. Drawing as Instrument, Drawings as Evidence: Capturing Mental Processes with Pencil and Paper

    Science.gov (United States)

    Puglionesi, Alicia

    2016-01-01

    Researchers in the mind sciences often look to the production and analysis of drawings to reveal the mental processes of their subjects. This essay presents three episodes that trace the emergence of drawing as an instrumental practice in the study of the mind. Between 1880 and 1930, drawings gained currency as a form of scientific evidence – as stable, reproducible signals from a hidden interior. I begin with the use of drawings as data in the child study movement, move to the telepathic transmission of drawings in psychical research and conclude with the development of drawing as an experimental and diagnostic tool for studying neurological impairment. Despite significant shifts in the theoretical and disciplinary organisation of the mind sciences in the early twentieth century, researchers attempted to stabilise the use of subject-generated drawings as evidence by controlling the contexts in which drawings were produced and reproduced, and crafting subjects whose interiority could be effectively circumscribed. While movements such as psychoanalysis and art therapy would embrace the narrative interpretation of patient art, neuropsychology continued to utilise drawings as material traces of cognitive functions. PMID:27292325

  1. Exploration of polyelectrolytes as draw solutes in forward osmosis processes

    KAUST Repository

    Ge, Qingchun

    2012-03-01

    The development of the forward osmosis (FO) process has been constrained by the slow development of appropriate draw solutions. Two significant concerns related to draw solutions are the draw solute leakage and intensiveenergy requirement in recycling draw solutes after the FO process. FO would be much attractive if there is no draw solute leakage and the recycle of draw solutes is easy and economic. In this study, polyelectrolytes of a series of polyacrylic acid sodium salts (PAA-Na), were explored as draw solutes in the FO process. The characteristics of high solubility in water and flexibility in structural configuration ensure the suitability of PAA-Na as draw solutes and their relative ease in recycle through pressure-driven membrane processes. The high water flux with insignificant salt leakage in the FO process and the high salt rejection in recycle processes reveal the superiority of PAA-Na to conventional ionic salts, such as NaCl, when comparing their FO performance via the same membranes. The repeatable performance of PAA-Na after recycle indicates the absence of any aggregation problems. The overall performance demonstrates that polyelectrolytes of PAA-Na series are promising as draw solutes, and the new concept of using polyelectrolytes as draw solutes in FO processes is applicable. © 2011 Elsevier Ltd.

  2. Improvement of cold wire drawing process by electropulsing

    OpenAIRE

    Sánchez Egea, Antonio José; González Rojas, Hernan Alberto; Jorba Peiró, Jordi

    2015-01-01

    The electroplastic effects on wire drawing process assisted with different short time current pulses configurations are investigated experimentally. The current pulses were induced to a specimen during the drawing process. The studied material is the 308L stainless steel. Current densities of 185 A/mm2, frequencies range from 140 to 350 Hz and pulse duration range from 100 to 250 μs were used in the electrically‐assisted wire drawing process. Frequency and pulse duration are...

  3. Forming Limit Diagram of Titanium and Stainless Steel Alloys to Study the Formability of Hydro-Mechanical Deep Drawing Parts

    Science.gov (United States)

    Shirizly, A.

    2005-08-01

    The increase demand for stronger, lighter and economic sheet metal products, make the Hydromecanical deep drawing process lately more and more popular. The Hydromecanical process is used in almost all types of sheet metal parts from home appliances and kitchenware to automotive and aviation industries. Therefore, many common materials were tested and characterized by their ability to sustain large strains via the well known Forming Limit Diagram (FLD). The aim of this work is to examine the forming capability if the Hydromecanical process in production of hemisphere parts made of materials commonly used in the aviation and aerospace industries. Experimental procedures were carried out to assess their ductility through FLD and the Forming Limit Carve (FLC).Two type of material sheets were tested herewith for demonstrating the procedure: commercial pure titanium and stainless steel 316L. A numerical simulation of the Hydromecanical process was examined and compared to self made Hydromecanical deep drawing of hemispherical parts.

  4. Forming Limit Diagram of Titanium and Stainless Steel Alloys to Study the Formability of Hydro-Mechanical Deep Drawing Parts

    International Nuclear Information System (INIS)

    Shirizly, A.

    2005-01-01

    The increase demand for stronger, lighter and economic sheet metal products, make the Hydromecanical deep drawing process lately more and more popular. The Hydromecanical process is used in almost all types of sheet metal parts from home appliances and kitchenware to automotive and aviation industries. Therefore, many common materials were tested and characterized by their ability to sustain large strains via the well known Forming Limit Diagram (FLD).The aim of this work is to examine the forming capability if the Hydromecanical process in production of hemisphere parts made of materials commonly used in the aviation and aerospace industries. Experimental procedures were carried out to assess their ductility through FLD and the Forming Limit Carve (FLC).Two type of material sheets were tested herewith for demonstrating the procedure: commercial pure titanium and stainless steel 316L. A numerical simulation of the Hydromecanical process was examined and compared to self made Hydromecanical deep drawing of hemispherical parts

  5. A Fundamental Study of Stretch-Drawing Process of Sheet Metals : Single and Double Operations

    Science.gov (United States)

    Gotoh, Manabu; Kim, Young-soo; Yamashita, Minoru

    1998-05-01

    Fundamental and informative data of axisymmetric stretch-drawing of several sheet metals with thichness of 0.7 1.0 mm are presented especially for single and double operations. Very small radius is applied to the die-profile (or -shoulder) in all operations to induce wall-thinning by the effect of bending-under-tension, from which the name `stretch-drawing' comes. It is clearly demonstrated that deeper cups could be formed by the single and double stretch-drawings from smaller cirlcular blanks due to such wall-thinning action than in the usual deep-drawing of larger blanks. From this fact, it is emphasized that the deep-drawability of a sheet metal is not evaluated simply by the conventional LDR (=limiting drawing ratio), but the depth of the drawn cup should also be taken into account. Many experimental data about various metals and thicknesses given in this paper offer a valueable information on this process for more general use which recommends to replace the conventional deep-drawing process by the stretch-drawing process both for single and double operations. In the single stretch-drawing, it is also confirmed that a deeper cup can be produced by raising the blank-holding force at later stage of operation. Fracturing is found to occur at the middle section of the wall part or at the die-profile other than at the punch profile common in the usual deep-drawing process. Numerical simulation of the single stretch-drawing process is also performed by use of DYNA-3D code to confirm that a satisfactory prediction especially in the depth of the drawn-cup can be done at least in a practical sense, although this kind of numerical analysis is very difficult because of the severity or localization of deformation around the die profile. The drawn cup of SUS304 among others fractures in a couple of weeks after the operation due to the residual circumferential tensile stress, whereas that of SUS304L does not. In the double stretch-drawing, it is confirmed that very deeper

  6. Imitation, Inspiration, and Creation: Cognitive Process of Creative Drawing by Copying Others' Artworks.

    Science.gov (United States)

    Okada, Takeshi; Ishibashi, Kentaro

    2017-09-01

    To investigate the cognitive processes underlying creative inspiration, we tested the extent to which viewing or copying prior examples impacted creative output in art. In Experiment 1, undergraduates made drawings under three conditions: (a) copying an artist's drawing, then producing an original drawing; (b) producing an original drawing without having seen another's work; and (c) copying another artist's work, then reproducing that artist's style independently. We discovered that through copying unfamiliar abstract drawings, participants were able to produce creative drawings qualitatively different from the model drawings. Process analyses suggested that participants' cognitive constraints became relaxed, and new perspectives were formed from copying another's artwork. Experiment 2 showed that exposure to styles of artwork considered unfamiliar facilitated creativity in drawing, while styles considered familiar did not do so. Experiment 3 showed that both copying and thoroughly viewing artwork executed using an unfamiliar style facilitated creativity in drawing, whereas merely thinking about alternative styles of artistic representation did not do so. These experiments revealed that deep encounters with unfamiliar artworks-whether through copying or prolonged observation-change people's cognitive representations of the act of drawing to produce novel artwork. Copyright © 2016 Cognitive Science Society, Inc.

  7. Development technique for deep drawing without blank holder to produce circular cup of brass alloy

    OpenAIRE

    Ali Hassan Saleh; Ammer Khalaf Ali

    2015-01-01

    Of this technique compared to the conventional deep drawing is that the circular cup can be carried out in single action press with limit In this paper a new mechanism for deep drawing was proposed to produce circular cup from thin plate without blank holder. In this technique the die assembly includes punch, die and die-punch. A 2D axisymmetric finite element model was built using DEFORM software. Effect of die geometry (half- cone angle) on maximum load, thickness distribution, strain distr...

  8. Prediction of forming limit in hydro-mechanical deep drawing of steel sheets using ductile fracture criterion

    Science.gov (United States)

    Oh, S.-T.; Chang, H.-J.; Oh, K. H.; Han, H. N.

    2006-04-01

    It has been observed that the forming limit curve at fracture (FLCF) of steel sheets, with a relatively higher ductility limit have linear shapes, similar to those of a bulk forming process. In contrast, the FLCF of sheets with a relatively lower ductility limit have rather complex shapes approaching the forming limit curve at neck (FLCN) towards the equi-biaxial strain paths. In this study, the FLCFs of steel sheets were measured and compared with the fracture strains predicted from specific ductile fracture criteria, including a criterion suggested by the authors, which can accurately describe FLCFs with both linear and complex shapes. To predict the forming limit for hydro-mechanical deep drawing of steel sheets, the ductile fracture criteria were integrated into a finite element simulation. The simulation, results based on the criterion suggested by authors accurately predicted the experimetal, fracture limits of steel sheets for the hydro-mechanical deep drawing process.

  9. DEEP DRAWING TECHNOLOGY WITH WALL IRONING IN MASS PACKAGING INDUSTRY

    Directory of Open Access Journals (Sweden)

    Saša Ranđelović

    2017-04-01

    Full Text Available Aluminum is a metal that is being increasingly used in the packaging industry in the modern metal forming technology, but it also provides a good opportunity for effective advertising and product promotion. Processing technologies for aluminum plastic deformation ensure superior packaging that meets the most rigorous demands in the food, pharmaceutical, chemical, and other industries. It is the case of mass production with very little material loss that offers the possibility of multiple recycling. On the other hand, today's products for general purpose consumers cannot be imagined without aggressive advertising that has a major impact on customers. Modern graphics techniques for printing images and different basic surfaces offer great opportunities that manufacturers use widely in the promotion and sale of their products.

  10. Novel concept for measurement of global blank draw-in when deep drawing outer skin automotive components

    Science.gov (United States)

    Kraft, M.; Bürgel, U.

    2017-09-01

    Modern press shops in the automotive industry have to deal with many challenges. One challenge is to achieve a consistent part quality. In order to reach this target, modern press systems and tools are equipped with several types of sensors. For example, there are sensors to measure characteristic values of blanks or sensors to measure the temperature in the tools. Often several sensors are used simultaneously. A significant parameter for determining the quality of draw panels is the draw-in amount. Previously, it was only possible to measure selective points of the draw-in amount due to sensors in the tools. All the known sensors have disadvantages, for example, they are exposed to wearing or susceptible to contamination. In this paper, a sensor system will be introduced that allows the measurement of the global draw-in amount of a drawn panel. Here, the draw-in amount is not measured in the draw die, it is measured during the transportation of the part to the following operation. Within the short transport time the part can be fully covered by an optical system. This leads to a multitude of advantages compared with previously known systems. For example, it is no longer necessary to equip every tool with sensor technology to measure the draw-in amount. Now it is sufficient to equip every press line with a single system to measure the draw-in. This fact leads not only to lower costs, it also simplifies the tool design. In addition, the risk of contamination of the sensor system is greatly reduced. The paper will also introduce an actuator that was built to locally vary the blankholder forces for a sheet metal forming process. Furthermore, an FEM model is presented that allows the determination of the effective range of these actuators. With the knowledge from the FEM simulation, an approach for an open loop control is presented. With this approach, the press shops at Opel are developing a control procedure in order to influence the stamping process positively.

  11. Spring back evaluation by bending under tension tests in conditions of multiaxial stresses corresponding to deep drawing processes. Application to AISI 304 DDQ stainless steel sheet; Evaluacion del springback mediante ensayos de doblado bajo tension en condiciones de multiaxialidad tipicas de los procesos de embuticion profunda. Aplicacion a chapa de acero inoxidable AISI 304 DDQ

    Energy Technology Data Exchange (ETDEWEB)

    Miguel, V.; Coello, J.; Martinez, A.; Calatayud, A.

    2013-09-01

    In this paper, a methodology has been developed for evaluating the spring back of AISI 304 DDQ stainless steel sheet based on a bending under tension test. The main difference of the methodology herein carried out is that tests are made under the multiaxial stresses state that take place in deep drawing processes. This affects to the level of stress value in the test and to the hardening state of the sheet. Springback evaluation has been done in two different areas. Bending area has been evaluated from elastic recovery ratio defined as the ratio between the bending radius after and before bending. Bending and unbending extreme has been studied from the measured curvature radius in this area and taking into account the geometric equivalence of the test with the drawing cups process. Results found allow to state that drawing ratio or deformation ratio have a negligible influence on the springback into the range of values experimented here. Bending radius has hardly influence as well while bending angle is the most significant variable. The results obtained are compared to those measured in deep-drawn cups, finding a great agreement. (Author)

  12. Analytical and regression models of glass rod drawing process

    Science.gov (United States)

    Alekseeva, L. B.

    2018-03-01

    The process of drawing glass rods (light guides) is being studied. The parameters of the process affecting the quality of the light guide have been determined. To solve the problem, mathematical models based on general equations of continuum mechanics are used. The conditions for the stable flow of the drawing process have been found, which are determined by the stability of the motion of the glass mass in the formation zone to small uncontrolled perturbations. The sensitivity of the formation zone to perturbations of the drawing speed and viscosity is estimated. Experimental models of the drawing process, based on the regression analysis methods, have been obtained. These models make it possible to customize a specific production process to obtain light guides of the required quality. They allow one to find the optimum combination of process parameters in the chosen area and to determine the required accuracy of maintaining them at a specified level.

  13. Delayed cracking in 301LN austenitic steel after deep drawing: Martensitic transformation and residual stress analysis

    International Nuclear Information System (INIS)

    Berrahmoune, M.R.; Berveiller, S.; Inal, K.; Patoor, E.

    2006-01-01

    The main objective of this work is to study the delayed cracking phenomenon of the 301LN unstable austenitic steel, by determining the distribution of residual stresses after deep drawing, taking into account the phase transformation. Deep drawing for different ratios is done for two different temperatures. Cracks appear for the highest drawing ratio (DR = 2.00) in the top of the cup. The breaking patterns observed using a scanning electron microscope show ductile fracture in the middle region, and both intergranular and transgranular rupture in the edges. Martensite contents throughout the cup wall and through the thickness are determined. Increasing the martensite content was found to have a great effect on the cracking sensitivity. X-ray diffraction allows us to determine the residual stresses in the martensitic phase. These last are positive, increase with increasing drawing ratios. The maximum value is located at the middle height of the cup, it exceeds 500 MPa for the 2.00 drawing ratio, and is less than 350 MPa for the 1.89 drawing ratio

  14. Dynamic strain aging of twinning-induced plasticity (TWIP) steel in tensile testing and deep drawing

    International Nuclear Information System (INIS)

    Kim, J.G.; Hong, S.; Anjabin, N.; Park, B.H.; Kim, S.K.; Chin, K.-G.; Lee, S.; Kim, H.S.

    2015-01-01

    The dynamic strain aging (DSA) of metallic materials due to solute atom diffusion to mobile dislocations induce deformation instability with load fluctuations and deformation localizations, hence reducing their sheet formability. In this paper, DSA behaviors of twinning induced plasticity (TWIP) steel with and without Al during tensile testing and deep drawing are investigated in terms of strain localization and the Portevin-Le Chatelier (PLC) band. A theoretical DSA model with internal variables of dislocation density and twin volume fraction is presented for an estimation of strain localization and strain hardening behavior of TWIP steels. The simulation results of the load history and PLC bands during tensile testing and deep drawing are in good agreement with the experimental values. A serration behavior is observed in high-Mn TWIP steels and its tensile residual stress is higher than that in the Al-added TWIP steels, which results in a deformation crack or delayed fracture of deep drawn specimens

  15. Effects of hypnosis and level of processing on repeated recall of line drawings.

    Science.gov (United States)

    McKelvie, S J; Pullara, M

    1988-07-01

    Moderately susceptible subjects (N = 30) initially judged 30 line drawings of objects for pleasantness (deep processing) and 30 line drawings for visual complexity (shallow processing), after which they were given two immediate recall tests. Following a 48-hr delay, subjects were allocated randomly to hypnosis, simulation, or neutral control conditions and were tested four more times. Subjects produced more correct and incorrect responses over the six trials and gave a higher number of correct responses for deep items than for shallow items. Over the last four trials, hypnosis had no general facilitative effect relative to the other two treatments, but the effect of depth was strongest for hypnotized subjects, who recalled more deep items than did the controls. Finally, both hypnotized and simulating subjects rated their recall as more involuntary and their experimental treatment as more helpful than did the controls. Caution is urged in the forensic use of hypnosis as a retrieval device.

  16. An experimental study on effect of process parameters in deep ...

    African Journals Online (AJOL)

    The effects of various deep drawing process parameters were determined by experimental study with the use of Taguchi fractional factorial design and analysis of variance for AA6111 Aluminum alloy. The optimum process parameters were determined based on their influence on the thickness variation at different regions ...

  17. An experimental study on effect of process parameters in deep ...

    African Journals Online (AJOL)

    DR OKE

    Indeed, deep drawing is one of the widely used sheet metal forming process ... and quality of business process by the use of statistical tools (Chen and Lyu, 2009). ... Selection of control factors and their levels are made on the basis of some.

  18. Complex approach mechanical properties and formability assessment of selected deep-drawing steels

    Directory of Open Access Journals (Sweden)

    J. Štaba

    2009-07-01

    Full Text Available The paper analyses the properties of deep-drawing sheets of three grades (Re = 320 to 475 MPa, surface-treated with hot-dip galvanizing, made of microalloyed steels. Deformation properties are assessed using tensile tests, technological Erichsen or cupping tests. These characteristics, as well as the behaviour of the surface layer, are also investigated under dynamic conditions (modified Erichsen test using a drop tester, or using flat bending fatigue tests. Using microscopic analysis the deformation properties of the surface layer are evaluated. The results show the compactness of the surface layer, high deformation characteristics, as well as fatigue properties of the investigated deep-drawing materials, suitable for application in the automotive industry.

  19. A Draw-In Sensor for Process Control and Optimization

    International Nuclear Information System (INIS)

    Mahayotsanun, Numpon; Cao, Jian; Peshkin, Michael

    2005-01-01

    Sheet metal forming is one of the major processes in manufacturing and is broadly used due to its high degree of design flexibility and low cost. In the sheet metal forming process, draw-in (planar movement of a sheet periphery) frequently occurs and is one of the most dominated indicators on the success of a forming process. Currently, monitoring and controlling draw-in during each stamping operation requires either time-consuming setup or a significant die modification. Most devices have been used only in laboratory settings. Our goal is to design a draw-in sensor providing high sensitivity in monitoring; ease of setup, measurement and controlling; and eventually be implemented in industry. Our design is based on the mutual inductance principle, which we considered physical factors affecting the characteristics of the draw-in sensor. Two different configurations, single-transducer and double-transducer of our draw-in sensors have been designed and tested. The results showed good linearity, especially for the double-transducer case. The output of the draw-in sensor was affected by the type of sheet metal, dimension of the transducer, and the distance between the transducer and the testing sheet metal. It was found that the result was insensitive to the waviness of the sheet metal if sheet thickness was thin. The invention, implementation, and integration of the draw-in sensor will have an enormous impact on revolutionizing the control of stamping process, will provide solid ground for process variation and uncertainty studies, and ultimately will affect the design decision process

  20. Complex approach mechanical properties and formability assessment of selected deep-drawing steels

    OpenAIRE

    J. Štaba; M. Buršák

    2009-01-01

    The paper analyses the properties of deep-drawing sheets of three grades (Re = 320 to 475 MPa), surface-treated with hot-dip galvanizing, made of microalloyed steels. Deformation properties are assessed using tensile tests, technological Erichsen or cupping tests. These characteristics, as well as the behaviour of the surface layer, are also investigated under dynamic conditions (modified Erichsen test using a drop tester), or using flat bending fatigue tests. Using microscopic analysis the d...

  1. Microstructure and Mechanical Behavior of Deep Drawing DC04 Steel at Different Length Scales

    OpenAIRE

    Schreijäg, Simone

    2013-01-01

    The deformation behavior of steels is strongly influenced by their microstructure which is a result of the alloying elements and thermal treatments. In this work, the microstructure and the deformation behavior of a non-alloyed deep drawing DC04 steel was investigated. The microstructure was analyzed during heat treatment by EBSD, then microcompression experiments were performed on selected microstructural units and then bulk steel samples were mechanically tested by tensile experiments.

  2. Multiscale deep drawing analysis of dual-phase steels using grain cluster-based RGC scheme

    International Nuclear Information System (INIS)

    Tjahjanto, D D; Eisenlohr, P; Roters, F

    2015-01-01

    Multiscale modelling and simulation play an important role in sheet metal forming analysis, since the overall material responses at macroscopic engineering scales, e.g. formability and anisotropy, are strongly influenced by microstructural properties, such as grain size and crystal orientations (texture). In the present report, multiscale analysis on deep drawing of dual-phase steels is performed using an efficient grain cluster-based homogenization scheme.The homogenization scheme, called relaxed grain cluster (RGC), is based on a generalization of the grain cluster concept, where a (representative) volume element consists of p  ×  q  ×  r (hexahedral) grains. In this scheme, variation of the strain or deformation of individual grains is taken into account through the, so-called, interface relaxation, which is formulated within an energy minimization framework. An interfacial penalty term is introduced into the energy minimization framework in order to account for the effects of grain boundaries.The grain cluster-based homogenization scheme has been implemented and incorporated into the advanced material simulation platform DAMASK, which purposes to bridge the macroscale boundary value problems associated with deep drawing analysis to the micromechanical constitutive law, e.g. crystal plasticity model. Standard Lankford anisotropy tests are performed to validate the model parameters prior to the deep drawing analysis. Model predictions for the deep drawing simulations are analyzed and compared to the corresponding experimental data. The result shows that the predictions of the model are in a very good agreement with the experimental measurement. (paper)

  3. BLANK SHAPE OPTIMIZATION ON DEEP DRAWING OF A TWIN ELLIPTICAL CUP USING THE REDUCED BASIS TECHNIQUE METHOD

    Directory of Open Access Journals (Sweden)

    Mahdi Hasanzadeh Golshani

    2015-08-01

    Full Text Available In this project thesis, initial blank shape optimization of a twin elliptical cup to reduce earring phenomenon in anisotropic sheet deep drawing process was studied .The purpose of this study is optimization of initial blank for reduction of the ears height value. The optimization process carried out using finite element method approach, which is coupled with Taguchi design of experiments and reduced basis technique methods. The deep drawing process was simulated in FEM software ABAQUS 6.12. The results of optimization show earring height and, in addition, a number of design variables and time of process can be reduced by using this methods. After optimization process with the proposed method, the maximum reduction of the earring height would be from 21.08 mm to 0.07 mm and also it could be reduced to 0 in some of the directions. The proposed optimization design in this article allows the designers to select the practical basis shapes. This leads to obtain better results at the end of the optimization process, to reduce design variables, and also to prevent repeating the optimization steps for indirect shapes.

  4. Warm Deep Drawing of Rectangular Parts of AZ31 Magnesium Alloy Sheet Adopting Variable Blank Holder Force

    International Nuclear Information System (INIS)

    Peng Yinghong; Chang Qunfeng; Li Dayong; Zeng Xiaoqin

    2007-01-01

    AZ31 magnesium alloy sheet with good shape and formability is fabricated by warm cross rolling. Uniaxial tensile tests are conducted using a Gleeble 3500 thermal - mechanical simulator, and the mechanical properties of AZ31 magnesium alloy sheet are analyzed. A warm deep drawing process of square part is also simulated by the finite element method. The influences of blank holder force on the formability are numerically investigated. A double-action hydraulic press that can realize adjustable blank holder forces is developed and its working principle and control system are introduced. Some warm deep drawing experiments of square parts of AZ31 magnesium alloy sheet are also performed. Different variation schemes of the blank holder force with the stroke of the punch are tested, and the experiment results are compared. Results show that the suitable blank holder force variation scheme is a ladder curve with the punch stroke. Adopting the variable blank holder force technique can improve 13.2% of the drawing depth of square parts of AZ31 magnesium alloy sheet

  5. An incremental analysis of a deep drawing steel’s material behaviour undergoing the predeformation using drawbeads

    Science.gov (United States)

    Schmid, H.; Suttner, S.; Merklein, M.

    2017-09-01

    Nowadays lightweight design in metal forming processes leads to complex deep drawing geometries, which can cause multiple damages. Therefore, drawbeads are one way to regulate and control material flow during the forming process. Not only in research, but also in industrial practice, it could be determined that material is work hardened passing drawbead geometries. It particularly means when material is pre-deformed with tensile and alternating bending loads. This incident also gives the opportunity to utilize it in a reasonable way if examined properly. To investigate these findings, a process oriented and comprehensive analysis of the material behaviour during these forming operations is needed. In this paper, sheet metal strips are linearly drawn through a drawbead and stopped after passing the drawbead. Within this forming operation, the material undergoes non-linear straining before reaching the in-plane position again. Here, the process will be stopped to investigate a permanent strengthening local along the sheet thickness. Therefore, microhardness measurements are realized before and after passing the drawbead. Because of its common use and its wide known material data, a deep drawing steel DC will be used for these studies. Additionally, the strategy is applied to advanced high strength steel.

  6. Thermomechanical analysis of an electrically assisted wire drawing process

    OpenAIRE

    Sánchez Egea, Antonio José; González Rojas, Hernan Alberto; Celentano, Diego Javier; Jorba Peiró, Jordi; Cao, Jia

    2017-01-01

    Electrically-assisted wire drawing process is a hybrid manufacturing process characterized by enhancement of the formability, ductility and elongation of the wire drawn specimen. A thermomechanical model to describe the change of the mechanical response due to the thermal contribution is proposed in this work. Additionally, a numerical simulation was conducted to study the potential and limitations of this hybrid process by using two different hardening laws: a phenomenological and a dislocat...

  7. Electro-thermo-mechanical coupling analysis of deep drawing with resistance heating for aluminum matrix composites sheet

    Science.gov (United States)

    Zhang, Kaifeng; Zhang, Tuoda; Wang, Bo

    2013-05-01

    Recently, electro-plastic forming to be a focus of attention in materials hot processing research area, because it is a sort of energy-saving, high efficient and green manufacturing technology. An electro-thermo-mechanical model can be adopted to carry out the sequence simulation of aluminum matrix composites sheet deep drawing via electro-thermal coupling and thermal-mechanical coupling method. The first step of process is resistance heating of sheet, then turn off the power, and the second step is deep drawing. Temperature distribution of SiCp/2024Al composite sheet by resistance heating and sheet deep drawing deformation were analyzed. During the simulation, effect of contact resistances, temperature coefficient of resistance for electrode material and SiCp/2024Al composite on temperature distribution were integrally considered. The simulation results demonstrate that Sicp/2024Al composite sheet can be rapidly heated to 400° in 30s using resistances heating and the sheet temperature can be controlled by adjusting the current density. Physical properties of the electrode materials can significantly affect the composite sheet temperature distribution. The temperature difference between the center and the side of the sheet is proportional to the thermal conductivity of the electrode, the principal cause of which is that the heat transfers from the sheet to the electrode. SiCp/2024Al thin-wall part can be intactly manufactured at strain rate of 0.08s-1 and the sheet thickness thinning rate is limited within 20%, which corresponds well to the experimental result.

  8. Analysis of earing behaviour in deep drawing of ASS 304 at elevated temperature

    Science.gov (United States)

    Gupta, Amit Kumar; Deole, Aditya; Kotkunde, Nitin; Singh, Swadesh Kumar; jella, Gangadhar

    2016-08-01

    Earing tendency in a deep drawn cup of circular blanks is one the most prominent characteristics observed due to anisotropy in a metal sheet. Such formation of uneven rim is mainly due to dissimilarity in yield stress as well as Lankford parameter (r- value) in different orientations. In this paper, an analytical function coupled with different yield functions viz., Hill 1948, Barlat 1989 and Barlat Yld 2000-2d has been used to provide an approximation of earing profile. In order to validate the results, material parameters for yield functions and hardening rule have been calibrated for ASS 304 at 250°C and deep drawing experiment is conducted to measure the earing profile. The predicted earing profiles based on analytical results have been validated using experimental earing profile. Based on this analysis, Barlat Yld 2000-2d has been observed to be a well suited yield model for deep drawing of ASS 304, which also confirms the reliability of analytical function for earing profile estimation.

  9. Deep Drawing of High-Strength Tailored Blanks by Using Tailored Tools

    Directory of Open Access Journals (Sweden)

    Thomas Mennecart

    2016-01-01

    Full Text Available In most forming processes based on tailored blanks, the tool material remains the same as that of sheet metal blanks without tailored properties. A novel concept of lightweight construction for deep drawing tools is presented in this work to improve the forming behavior of tailored blanks. The investigations presented here deal with the forming of tailored blanks of dissimilar strengths using tailored dies made of two different materials. In the area of the steel blank with higher strength, typical tool steel is used. In the area of the low-strength steel, a hybrid tool made out of a polymer and a fiber-reinforced surface replaces the steel half. Cylindrical cups of DP600/HX300LAD are formed and analyzed regarding their formability. The use of two different halves of tool materials shows improved blank thickness distribution, weld-line movement and pressure distribution compared to the use of two steel halves. An improvement in strain distribution is also observed by the inclusion of springs in the polymer side of tools, which is implemented to control the material flow in the die. Furthermore, a reduction in tool weight of approximately 75% can be achieved by using this technique. An accurate finite element modeling strategy is developed to analyze the problem numerically and is verified experimentally for the cylindrical cup. This strategy is then applied to investigate the thickness distribution and weld-line movement for a complex geometry, and its transferability is validated. The inclusion of springs in the hybrid tool leads to better material flow, which results in reduction of weld-line movement by around 60%, leading to more uniform thickness distribution.

  10. Dynamic analysis of six-bar mechanical press for deep drawing

    Science.gov (United States)

    Mitsi, S.; Tsiafis, I.; Bouzakis, K. D.

    2017-02-01

    This paper analyzes the dynamical behavior of a six-bar linkage used in mechanical presses for metal forming such as deep drawing. In the under study mechanism, a four-bar linkage is connected to a slider through an articulated binary link. The motion of the six-bar linkage is studied by kinematic analysis developing an analytical method. Furthermore, using an iterative method and d’ Alembert’s principle, the joint forces and drive moment are evaluated considering joint frictions. The simulation results obtained with a MATLAB program are validated by comparing the theoretical values of the input moment with the ones obtained from the conservation of energy law.

  11. Effect of Hydraulic Pressure on Warm Hydro Mechanical Deep Drawing of Magnesium Alloy Sheet

    Science.gov (United States)

    Liu, Wei; Wu, Linzhi; Yuan, Shijian

    The uniaxial tensile test and hydraulic bulging test of AZ31 magnesium alloy sheets were applied to study the influence of temperature on the material properties and obtain the forming limit curves at different temperatures. Numerical simulations of warm hydro mechanical deep drawing were carried out to investigate the effect of hydraulic pressure on the formability of a cylindrical cup, and the simplified hydraulic pressure profiles were used to simulate the loading procedure of hydraulic pressure. The optimal hydraulic pressure at different temperatures were given and verified by experimental studies at temperature 100°C and 170V.

  12. Characterisation and full-scale production testing of multifunctional surfaces for deep drawing applications

    DEFF Research Database (Denmark)

    Godi, Alessandro; Grønbæk, J.; De Chiffre, Leonardo

    2017-01-01

    assisted polishing. Advanced methods are employed to characterise the tools' surface topographies, detecting the surface features and analysing them separately according to their specific function. Four different multifunctional dies as well as two un-textured references are selected for testing. The tests......Full-scale deep drawing tests using tools featuring multifunctional surfaces are carried out in a production environment. Multifunctional tools display regularly spaced, transversal grooves for lubricant retention obtained by hard-turning, separated by smooth bearing plateaus realized by robot...

  13. Humor drawings evoked temporal and spectral EEG processes

    Science.gov (United States)

    Kuo, Hsien-Chu; Chuang, Shang-Wen

    2017-01-01

    Abstract The study aimed to explore the humor processing elicited through the manipulation of artistic drawings. Using the Comprehension–Elaboration Theory of humor as the main research background, the experiment manipulated the head portraits of celebrities based on the independent variables of facial deformation (large/small) and addition of affective features (positive/negative). A 64-channel electroencephalography was recorded in 30 participants while viewing the incongruous drawings of celebrities. The electroencephalography temporal and spectral responses were measured during the three stages of humor which included incongruity detection, incongruity comprehension and elaboration of humor. Analysis of event-related potentials indicated that for humorous vs non-humorous drawings, facial deformation and the addition of affective features significantly affected the degree of humor elicited, specifically: large > small deformation; negative > positive affective features. The N170, N270, N400, N600-800 and N900-1200 components showed significant differences, particularly in the right prefrontal and frontal regions. Analysis of event-related spectral perturbation showed significant differences in the theta band evoked in the anterior cingulate cortex, parietal region and posterior cingulate cortex; and in the alpha and beta bands in the motor areas. These regions are involved in emotional processing, memory retrieval, and laughter and feelings of amusement induced by elaboration of the situation. PMID:28402573

  14. Humor drawings evoked temporal and spectral EEG processes.

    Science.gov (United States)

    Wang, Regina W Y; Kuo, Hsien-Chu; Chuang, Shang-Wen

    2017-08-01

    The study aimed to explore the humor processing elicited through the manipulation of artistic drawings. Using the Comprehension-Elaboration Theory of humor as the main research background, the experiment manipulated the head portraits of celebrities based on the independent variables of facial deformation (large/small) and addition of affective features (positive/negative). A 64-channel electroencephalography was recorded in 30 participants while viewing the incongruous drawings of celebrities. The electroencephalography temporal and spectral responses were measured during the three stages of humor which included incongruity detection, incongruity comprehension and elaboration of humor. Analysis of event-related potentials indicated that for humorous vs non-humorous drawings, facial deformation and the addition of affective features significantly affected the degree of humor elicited, specifically: large > small deformation; negative > positive affective features. The N170, N270, N400, N600-800 and N900-1200 components showed significant differences, particularly in the right prefrontal and frontal regions. Analysis of event-related spectral perturbation showed significant differences in the theta band evoked in the anterior cingulate cortex, parietal region and posterior cingulate cortex; and in the alpha and beta bands in the motor areas. These regions are involved in emotional processing, memory retrieval, and laughter and feelings of amusement induced by elaboration of the situation. © The Author (2017). Published by Oxford University Press.

  15. A methodology to obtain strain indicators under deep drawing multiaxial stresses. Application to DC-05 electro galvanized steel (UNE in ISO 10130)

    International Nuclear Information System (INIS)

    Miguel, V.; Catalayud, A.; Ferrer, C.

    2007-01-01

    In this work a methodology to investigate deep drawing quality steel sheets deformation tendency under multiaxial deep drawing stresses has been proposed. the method consists in assaying a sheet in a wedge die in order to order to introduce a pure shear estate in the material 0 degree centigree, 45 degree centigree and 90 degree centigree rolling directions are selected in the assays, and transversal strain is the variable considered in them. a strain coefficient 0/% has been defined in order to evaluate thickness variations in the test. almost no changes in thickness have been registered and this indicates that strain carried out in the test is similar to that taking place in deep drawing. The stress necessary for practice a certain plastic deformation is obtained too and a potential function between them is formulated. Indicators presented in this work are compared to anisotropy and strength coefficients obtained in normalized tensile tests. these results allow us to justify the steel behaviour in the cup deep drawing processes related to ear forming. (Author) 11 refs

  16. High temperature tensile properties and deep drawing of fully green composites

    Directory of Open Access Journals (Sweden)

    2009-01-01

    Full Text Available In recent years, research and development of materials using biomass sources are much expected to construct a sustainable society. The so-called green composite consisting of natural fibers and biodegradable resin, is one of the most promising materials in developing biomass products. In this study, especially, we focus on the tensile deformation behavior of the green composites reinforced with ramie woven fabrics at high temperature. The results show that the fracture strain at high temperatures increases larger than that of room temperature, and initial deformation resistance of the composites seen at room temperature does not appear at high temperatures. Thus, several conditions to cause more deformability of the green composites were found. Finally, in order to utilize such deformability, Lankford-values of the green composites were clarified, and deep drawing was carried out for sheet materials made of the green composites.

  17. A Study on DLC Tool Coating for Deep Drawing and Ironing of Stainless Steel

    DEFF Research Database (Denmark)

    Üstünyagiz, Esmeray; Hafis Sulaiman, Mohd; Christiansen, Peter

    2018-01-01

    ) to replicate industrial ironing of deep drawn, stainless steel parts. Non-hazardous tribo-systems in form of a double layer Diamond-like coated tool applied under dry condition or with an environmentally friendly lubricant were investigated via emulating industrial process conditions in laboratory tests...

  18. Predicting Process Behaviour using Deep Learning

    OpenAIRE

    Evermann, Joerg; Rehse, Jana-Rebecca; Fettke, Peter

    2016-01-01

    Predicting business process behaviour is an important aspect of business process management. Motivated by research in natural language processing, this paper describes an application of deep learning with recurrent neural networks to the problem of predicting the next event in a business process. This is both a novel method in process prediction, which has largely relied on explicit process models, and also a novel application of deep learning methods. The approach is evaluated on two real da...

  19. Formability of dual-phase steels in deep drawing of rectangular parts: Influence of blank thickness and die radius

    Science.gov (United States)

    López, Ana María Camacho; Regueras, José María Gutiérrez

    2017-10-01

    The new goals of automotive industry related with environment concerns, the reduction of fuel emissions and the security requirements have driven up to new designs which main objective is reducing weight. It can be achieved through new materials such as nano-structured materials, fibre-reinforced composites or steels with higher strength, among others. Into the last group, the Advance High Strength Steels (AHSS) and particularly, dual-phase steels are in a predominant situation. However, despite of their special characteristics, they present issues related to their manufacturability such as springback, splits and cracks, among others. This work is focused on the deep drawing processof rectangular shapes, a very usual forming operation that allows manufacturing several automotive parts like oil pans, cases, etc. Two of the main parameters in this process which affect directly to the characteristics of final product are blank thickness (t) and die radius (Rd). Influence of t and Rd on the formability of dual-phase steels has been analysed considering values typically used in industrial manufacturing for a wide range of dual-phase steels using finite element modelling and simulation; concretely, the influence of these parameters in the percentage of thickness reduction pt(%), a quite important value for manufactured parts by deep drawing operations, which affects to its integrity and its service behaviour. Modified Morh Coulomb criteria (MMC) has been used in order to obtain Fracture Forming Limit Diagrams (FFLD) which take into account an important failure mode in dual-phase steels: shear fracture. Finally, a relation between thickness reduction percentage and studied parameters has been established fordual-phase steels, obtaining a collection of equations based on Design of Experiments (D.O.E) technique, which can be useful in order to predict approximate results.

  20. Mean associative multiplicities in deep inelastic processes

    International Nuclear Information System (INIS)

    Dzhaparidze, G.Sh.; Kiselev, A.V.; Petrov, V.A.

    1981-01-01

    The associative hadron multiplicities in deep inelastic and Drell--Yan processes are studied. In particular the mean multiplicities in different hard processes in QCD are found to be determined by the mean multiplicity in parton jet [ru

  1. Imitation, Inspiration, and Creation: Cognitive Process of Creative Drawing by Copying Others' Artworks

    Science.gov (United States)

    Okada, Takeshi; Ishibashi, Kentaro

    2017-01-01

    To investigate the cognitive processes underlying creative inspiration, we tested the extent to which viewing or copying prior examples impacted creative output in art. In Experiment 1, undergraduates made drawings under three conditions: (a) copying an artist's drawing, then producing an original drawing; (b) producing an original drawing without…

  2. Deep inelastic processes and the parton model

    International Nuclear Information System (INIS)

    Altarelli, G.

    The lecture was intended as an elementary introduction to the physics of deep inelastic phenomena from the point of view of theory. General formulae and facts concerning inclusive deep inelastic processes in the form: l+N→l'+hadrons (electroproduction, neutrino scattering) are first recalled. The deep inelastic annihilation e + e - →hadrons is then envisaged. The light cone approach, the parton model and their relation are mainly emphasized

  3. Analysis of Tube Drawing Process – A Finite Element Approach ...

    African Journals Online (AJOL)

    In this paper the effect of die semi angle on drawing load in cold tube drawing has been investigated numerically using the finite element method. The equation governing the stress distribution was derived and solved using Galerkin finite element method. An isoparametric formulation for the governing equation was utilized ...

  4. Deep drawing experiences of niobium disk for PEFP SRF cavity prototype

    International Nuclear Information System (INIS)

    Kim, Han Sung; An, Sun; Zhang, Liping; Tang, Yazhe; Li, Ying Min; Kwon, Hyeok Jung; Cho, Yong Sub

    2009-01-01

    A superconducting radio frequency (SRF) cavity with a geometrical beta of 0.42 has been designed to accelerate a proton beam after 100 MeV for an extension of Proton Engineering Frontier Project (PEFP). The designed cavity shape is an elliptical and the resonant frequency is 700 MHz. In order to confirm the RF and mechanical properties of the cavity, two prototypes of copper cavities have been fabricated and tested. Based on the experiences gained with the copper prototypes, two niobium prototypes have been designed. One is two-cell cavity and the other is five cell cavity. The two-cell cavity is for finalizing the niobium cavity production procedure and testing the cavity RF properties at a low temperature and moderate power level. The five-cell cavity is for checking the production quality and testing vertical test system in the future. Both of them are under fabrication. Through the fabrication of the niobium prototype, several issues such as deep drawing, electron beam welding and surface treatment will be addressed. The drawing of the PEPF SRF low beta cavity is shown in Fig. 1. Major parameters for the cavity are like following. - Frequency: 700 MHz - Operating mode: TM010 pi mode - Cavity type: Elliptical - Geometrical beta: 0.42 - Number of cells: 5 per cavity - Accelerating gradient: 8 MV/m - Epeak/Eacc: 3.71 - Bpeak/Eacc: 7.47 mT/(MV/m) - R/Q: 102.3 ohm - Epeak: 29.68 MV/m - Field flatness: 1.56 % - Cell to cell coupling: 1.41 % - Geometrical factor: 121.68 ohm - Cavity wall thickness: 4.3 mm - Lorentz force detuning: 0.4 Hz/(MV/m)2 - Stiffening structure: Double ring - Effective length: 0.45 m - External Q of FPC: 8.0E5 ±20 % - HOM load: less than 2 W - HOM Qext requirement: less than 3.0E5 At present, all the niobium disk and plates for cavity and NbTi flanges for beam pipe flange are prepared

  5. A novel feedback control system – Controlling the material flow in deep drawing using distributed blank-holder force

    DEFF Research Database (Denmark)

    Endelt, Benny Ørtoft; Tommerup, Søren; Danckert, Joachim

    2013-01-01

    The performance of a feedback control system is often limited by the quality of the model on which it is based, and often the controller design is based on trial and error due to insufficient modeling capabilities. A framework is proposed where the controller design is based on classical state...... on a deep drawing operation where the objective was to control material flow throughout the part using only spatial information regarding flange draw-in. The control system controls both the magnitude and distribution of the blank-holder force. The methodology proved stable and flexible with respect...

  6. The Design of Drawing Process of Cylindrical Cup with Oval Bottom Using Computer Simulation

    Directory of Open Access Journals (Sweden)

    Kapustová Mária

    2017-01-01

    Full Text Available Based on technological calculations, technology of one-operation drawing without blankholder was designed for production of a large-dimensional drawpiece with shape of welded on concave bottom. The necessary drawing force was also defined by calculation as maximum drawing force for trimming of drawpiece bottom. This contribution points out to the importance of FEM simulation of drawing process in order to verify the design of production technology of drawpiece with shape of welded on concave bottom on the basis of technological calculations. Simulation programme Deform verified the construction design of drawing tool determined for drawpiece production by first draw, and also determined the drawing force actually consumed during plastic deformation of drawpiece shape. Used simulation software confirmed correctness of drawing tool construction, as correct material plastic flow in drawing tool was monitored and production of drawpiece was faultless.

  7. Using Drawing Technology to Assess Students' Visualizations of Chemical Reaction Processes

    Science.gov (United States)

    Chang, Hsin-Yi; Quintana, Chris; Krajcik, Joseph

    2014-01-01

    In this study, we investigated how students used a drawing tool to visualize their ideas of chemical reaction processes. We interviewed 30 students using thinking-aloud and retrospective methods and provided them with a drawing tool. We identified four types of connections the students made as they used the tool: drawing on existing knowledge,…

  8. Deep Drawing Simulation Of High And Ultrahigh Strength Steels Under Consideration Of Anisotropic Hardening

    International Nuclear Information System (INIS)

    Roll, Karl; Faust, Alexander; Kessler, Lutz

    2007-01-01

    In today's sheet metal forming simulation, most attention is paid to yield loci functions, which describe the anisotropy of the material in yielding. The coefficients, defining the shape of the yield locus in these functions are usually fitted at a certain level of plastic work and are then valid for the whole range of plastic deformation. Modern high and ultrahigh strength steels, especially those with induced plasticity, may often exhibit only a very small anisotropy in yielding, but a severe anisotropy in work hardening for different loading conditions. This behavior can not be described by fitting the yield locus at a specific value of plastic deformation. An approach to take into account the anisotropic hardening of sheet metals is to provide different yield curves for several loading conditions and expand the yield locus dependent on the current form of load. By doing this, one can use a comparatively simple yield locus, like that of Hill from 1948, because all anisotropy is given by the different hardening curves. For the commercial FEM code LS DYNA the material model MATFEM Generalized Yield is available as a user subroutine, which supports this approach. In this paper, forming simulation results of different yield loci are compared with experimental results. The simulations were carried out in LS-DYNA with the Barlat 89 and 2000 yield loci and isotropic hardening and with the GenYld model combining a Hill 48 yield locus and anisotropic hardening. The deep drawing experiments were conducted on a hydraulic press, measuring binder and punch forces. The deformation of the sheet was measured by optical grid analysis. A comparison of the simulated and measured plastic strains shows that using a model including anisotropic hardening can produce better results than the usage of a complex yield locus but isotropic hardening for the examined materials. This might be interesting for e.g. spring back simulations. By combining a simple yield locus with anisotropic

  9. Mean associated multiplicities in deep inelastic processes

    International Nuclear Information System (INIS)

    Dzhaparidze, G.Sh.; Kiselev, A.V.; Petrov, V.A.

    1982-01-01

    A formula is derived for the mean hadron multiplicity in the target fragmentation range of deep inelastic scattering processes. It is shown that in the high-x region the ratio of the mean multiplicities in the current fragmentation region and in the target fragmentation region tends to unity at high energies. The mean multiplicity for the Drell-Yan process is considered

  10. Draw solutions for forward osmosis processes: Developments, challenges, and prospects for the future

    KAUST Repository

    Ge, Qingchun

    2013-09-01

    Forward osmosis (FO) has emerged as one of potential technologies to mitigate clean water and energy shortage. Not only can it produce clean water but also energy by employing draw solutes to induce osmotic gradients across semipermeable membranes as the driving force for water production and power generation. Ideally, the semipermeable membrane performs as a barrier that allows only water to pass through but rejects all others. However, in reality, depending on draw solute\\'s chemistry property and physical structure, the reverse flux of draw solutes may take place across FO membranes which not only results in a lower effective osmotic driving force but also facilitates fouling. In addition, the asymmetric structure of FO membranes and the transport resistance of draw solutes within the FO membranes cause concentration polarization and lower the water flux. Furthermore, the regeneration of draw solutes from diluted draw solutions and the production of clean water might be energy-intensive if inappropriate draw solutes and recycle processes are utilized. Therefore, in this work we aim to give a comprehensive review on the progress of draw solution for FO processes. An assessment on the advantages and limitations of the existing draw solutes are made. Various FO integrated processes for water production and draw solute regeneration are exemplified. We also highlight the challenges and future research directions for the molecular design of better draw solutes. © 2013 Elsevier B.V.

  11. Modern problems of deep processing of coal

    International Nuclear Information System (INIS)

    Ismagilov, Z.R.

    2013-01-01

    Present article is devoted to modern problems of deep processing of coal. The history and development of new Institute of Coal Chemistry and Material Sciences of Siberian Branch of Russian Academy of Science was described. The aims and purposes of new institute were discussed.

  12. Mean associated multiplicities in deep inelastic processes

    International Nuclear Information System (INIS)

    Dzhaparidze, G.S.; Kiselev, A.V.; Petrov, V.A.

    1982-01-01

    A formula is derived for the mean multiplicity of hadrons in the target-fragmentation region in the process of deep inelastic scattering. It is shown that in the region of large x the ratio of the mean multiplicities in the current- and target-fragmentation regions tends to unity at high energies. The mean multiplicity in the Drell-Yan process is also discussed

  13. Influence of the relative deformation rate on tube processing by ultrasonic vibration drawing

    International Nuclear Information System (INIS)

    Susan, M.; Bujoreanu, L. G.; Galusca, D. G.; Munteanu, C.; Lliescu, V.

    2004-01-01

    After a brief review of the friction reversion mechanism during ultrasonic vibration drawing of tubes (UVD), the paper introduces a method to determine the drawing force based on the theorem of total consumed power, in the case of tube processing. The experiments performed on tubes made from 10TiNiCr180 (AISI321) austenitic stainless steel confirm the superiority of UVD technology regarding the diminution of the drawing force, the increase of the plasticity and the improvement of the safety coefficient, tendencies that are enhanced with the decrease of the relative drawing rate. The best results were obtained for the relative drawing rate of 0.12 for which the drawing force decreased with 33%, plasticity increased with 9% and safety coefficient with 22%, as compared to CT. (Author) 10 refs

  14. NUMERICAL SIMULATION OF RESIDUAL STRESSES GENERATED IN THE WIRE DRAWING PROCESS FOR DIFFERENT PROCESS PARAMETERS

    Directory of Open Access Journals (Sweden)

    Juliana Zottis

    2014-03-01

    Full Text Available The drawing process of steel bars is usually used to check better dimensional accuracy and mechanical properties to the material. In the other hand, the major concern found in manufacturing axes through this process is the appearance of distortion of shape. Such distortions are directly linked to the accumulation of residual stresses generated during the processes. As a result, this paper aims to study the influence of process parameters such as shape of puller, speed and lubrication used in wire drawing analyzing the accumulation of residual stress after the process. The stress analysis was performed by FEM being used two simulation software: Simufact.formingGP and DeformTM. Through these analyzes, it was found that the shape of how the bar is pulled causes a reduction of up to 100 MPa in residual stresses in the center of the bar, which represents an important factor in the study of the possible causes of the distortion. As well as factors speed and homogeneity of lubrication significantly altered the profile of residual stresses in the bar.

  15. Performance Evaluation of Absorbent Solution for Draw Solute Recovery in Forward Osmosis Desalination Process

    International Nuclear Information System (INIS)

    Kim, Young; Lee, Jong Hoon; Lee, Kong Hoon; Kim, Yu-Chang; Oh, Dong Wook; Lee, Jungho

    2013-01-01

    Although forward osmosis desalination technology has drawn substantial attention as a next-generation desalination method, the energy efficiency of its draw solution treatment process should be improved for its commercialization. When ammonium bicarbonate is used as the draw solute, the system consists of forward-osmosis membrane modules, draw solution separation and recovery processes. Mixed gases of ammonia and carbon dioxide generated during the draws solution separation, need to be recovered to re-concentrate ammonium bicarbonate solution, for continuous operation as well as for the economic feasibility. The diluted ammonium bicarbonate solution has been proposed as the absorbent for the draw solution regeneration. In this study, experiments are conducted to investigate performance and features of the absorption corresponding to absorbent concentration. It is concluded that ammonium bicarbonate solution can be used to recover the generated ammonia and carbon dioxide. The results will be applied to design and operation of pilot-scale forward-osmosis desalination system

  16. Performance Evaluation of Absorbent Solution for Draw Solute Recovery in Forward Osmosis Desalination Process

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young; Lee, Jong Hoon; Lee, Kong Hoon; Kim, Yu-Chang; Oh, Dong Wook; Lee, Jungho [Korea Institute of Machinery Materials, Daejeon (Korea, Republic of)

    2013-04-15

    Although forward osmosis desalination technology has drawn substantial attention as a next-generation desalination method, the energy efficiency of its draw solution treatment process should be improved for its commercialization. When ammonium bicarbonate is used as the draw solute, the system consists of forward-osmosis membrane modules, draw solution separation and recovery processes. Mixed gases of ammonia and carbon dioxide generated during the draws solution separation, need to be recovered to re-concentrate ammonium bicarbonate solution, for continuous operation as well as for the economic feasibility. The diluted ammonium bicarbonate solution has been proposed as the absorbent for the draw solution regeneration. In this study, experiments are conducted to investigate performance and features of the absorption corresponding to absorbent concentration. It is concluded that ammonium bicarbonate solution can be used to recover the generated ammonia and carbon dioxide. The results will be applied to design and operation of pilot-scale forward-osmosis desalination system.

  17. Hadron final states in deep inelastic processes

    International Nuclear Information System (INIS)

    Bjorken, J.D.

    1976-05-01

    Lectures are presented dealing mainly with the description and discussion of hadron final states in electroproduction, colliding beams, and neutrino reactions from the point of view of the simple parton model. Also the space-time evolution of final states in the parton model is considered. It is found that the picture of space-time evolution of hadron final states in deep inelastic processes isn't totally trivial and that it can be made consistent with the hypotheses of the parton model. 39 references

  18. Drawing Links between the Autism Cognitive Profile and Imagination: Executive Function and Processing Bias in Imaginative Drawings by Children with and without Autism

    Science.gov (United States)

    Ten Eycke, Kayla D.; Müller, Ulrich

    2018-01-01

    Little is known about the relation between cognitive processes and imagination and whether this relation differs between neurotypically developing children and children with autism. To address this issue, we administered a cognitive task battery and Karmiloff-Smith's drawing task, which requires children to draw imaginative people and houses. For…

  19. Study Of The Wet Multipass Drawing Process Applied On High Strength Thin Steel Wires

    Science.gov (United States)

    Thimont, J.; Felder, E.; Bobadilla, C.; Buessler, P.; Persem, N.; Vaubourg, JP.

    2011-05-01

    Many kinds of high strength thin steel wires are involved in so many applications. Most of the time, these wires are made of a pearlitic steel grade. The current developments mainly concern the wire last drawing operation: after a patenting treatment several reduction passes are performed on a slip-type multipass drawing machine. This paper focuses on modeling this multipass drawing process: a constitutive law based on the wire microstructure evolutions is created, a mechanical study is performed, a set of experiments which enables determining the process friction coefficients is suggested and finally the related analytical model is introduced. This model provides several general results about the process and can be used in order to set the drawing machines.

  20. Phenomenology of deep-inelastic processes

    International Nuclear Information System (INIS)

    Moretto, L.G.

    1983-03-01

    The field of heavy-ion deep-inelastic reactions is reviewed with particular attention to the experimental picture. The most important degrees of freedom involved in the process are identified and illustrated with relevant experiments. Energy dissipation and mass transfer are discussed in terms of particles and/or phonons exchanged in the process. The equilibration of the fragment neutron-to-proton ratios is inspected for evidence of giant isovector resonances. The angular momentum effects are observed in the fragment angular distributions and the angular momentum transfer is inferred from the magnitude and alignment of the fragments spins. The possible sources of light particles accompanying the deep-inelastic reactions are discussed. The use of the sequentially emitted particles as angular momentum probes is illustrated. The significance and uses of a thermalized component emitted by the dinucleus is reviewed. The possible presence of Fermi jets in the prompt component is shown to be critical to the justification of the one-body theories

  1. The phenomenology of deep-inelastic processes

    International Nuclear Information System (INIS)

    Moretto, L.G.

    1983-01-01

    The field of heavy-ion deep-inelastic reactions is reviewed with particular attention to the experimental picture. The most important degrees of freedom involved in the process are identified and illustrated with relevant experiments. Energy dissipation and mass transfer are discussed in terms of particles and/or phonons exchanged in the process. The equilibration of the fragment neutron-to-proton ratios is inspected for evidence of giant isovector resonances. The angular momentum effects are observed in the fragment angular distributions and the angular momentum transfer is inferred from the magnitude and alignment of the fragments spins. The possible sources of light particles accompanying the deep-inelastic reactions are discussed. The use of the sequentially emitted particles as angular momentum probes is illustrated. The significance and uses of a thermalized component emitted by the dinucleus is reviewed. The possible presence of Fermi jets in the prompt component is shown to be critical to the justification of the one-body theories. (orig.)

  2. Forming Behaviour in Laser Shock Drawing

    OpenAIRE

    Schulze Niehoff, H.; Vollertsen, F.; Wielage, H.

    2008-01-01

    Through the continuing trend of miniaturization new cost efficient and fast methods for processing small parts are required. In this paper a new non-mechanical process for the forming process of micro deep drawing is presented. This new deep drawing process utilizes a laser initiated plasma shock wave at the target, which forms the sheet. Several pulses can be applied at one point and therefore high forming degrees can be reached without increasing the energy density. In this paper the pressu...

  3. Application of ConceptDraw Office for planning, documenting, monitoring of operating processes

    International Nuclear Information System (INIS)

    Bocharnikov, O.P.; Savenko, S.V.; Nikiforov, N.S.

    2011-01-01

    ConceptDraw Office allows effectively deciding the following tasks: to carry out planning, designing, control of implementation of production processes; to prepare working documents (engineering diagrams, process flor diagrams, evacuation and emergency plans; to create dashboards with information for organization management; to distribute the organization resources with the purpose of increase of efficiency and safety of operating processes.

  4. Reduction of tensile residual stresses during the drawing process of tungsten wires

    International Nuclear Information System (INIS)

    Rodriguez Ripoll, Manel; Weygand, Sabine M.; Riedel, Hermann

    2010-01-01

    Tungsten wires are commonly used in the lighting industry as filaments for lamps. During the drawing process, the inhomogeneous deformation imparted by the drawing die causes tensile residual stresses at the wire surface in circumferential direction. These stresses have a detrimental effect for the wire because they are responsible for driving longitudinal cracks, known as splits. This work proposes two methods for reducing the residual stresses during wire drawing, namely applying an advanced die geometry and performing an inexpensive post-drawing treatment based on targeted bending operations. These two methods are analyzed with finite element simulations using material parameters obtained by mechanical tests on tungsten wires at different temperatures as input data. The computed results predict a substantial reduction of the circumferential residual stresses, thus reducing the risk of splitting.

  5. Deep Learning in Visual Computing and Signal Processing

    OpenAIRE

    Xie, Danfeng; Zhang, Lei; Bai, Li

    2017-01-01

    Deep learning is a subfield of machine learning, which aims to learn a hierarchy of features from input data. Nowadays, researchers have intensively investigated deep learning algorithms for solving challenging problems in many areas such as image classification, speech recognition, signal processing, and natural language processing. In this study, we not only review typical deep learning algorithms in computer vision and signal processing but also provide detailed information on how to apply...

  6. Full-fledged temporal processing: bridging the gap between deep linguistic processing and temporal extraction

    Directory of Open Access Journals (Sweden)

    Francisco Costa

    2013-07-01

    Full Text Available The full-fledged processing of temporal information presents specific challenges. These difficulties largely stem from the fact that the temporal meaning conveyed by grammatical means interacts with many extra-linguistic factors (world knowledge, causality, calendar systems, reasoning. This article proposes a novel approach to this problem, based on a hybrid strategy that explores the complementarity of the symbolic and probabilistic methods. A specialized temporal extraction system is combined with a deep linguistic processing grammar. The temporal extraction system extracts eventualities, times and dates mentioned in text, and also temporal relations between them, in line with the tasks of the recent TempEval challenges; and uses machine learning techniques to draw from different sources of information (grammatical and extra-grammatical even if it is not explicitly known how these combine to produce the final temporal meaning being expressed. In turn, the deep computational grammar delivers richer truth-conditional meaning representations of input sentences, which include a principled representation of temporal information, on which higher level tasks, including reasoning, can be based. These deep semantic representations are extended and improved according to the output of the aforementioned temporal extraction module. The prototype implemented shows performance results that increase the quality of the temporal meaning representations and are better than the performance of each of the two components in isolation.

  7. Agile Drawing

    DEFF Research Database (Denmark)

    Kruse Aagaard, Anders; Lahmy, Maya

    2014-01-01

    This paper aims to discuss the expanding territory of the architectural drawing through digital fabrication processes and with this angle suggest an experimental practice in research and education. At two workshops held throughout June 2014 this approach and mind-set was presented to 2nd year...... on the correlation between tool and drawing. The output of the workshop is considered one accumulated body of drawings and artefacts, mapping some aspect of the method put forward in a tangible materialised approach....

  8. Frictional interactions in forming processes: New studies with transparent sapphire strip-drawing dies

    Science.gov (United States)

    Rao, R. S.; Lu, C. Y.; Wright, P. K.; Devenpeck, M. L.; Richmond, O.; Appleby, E. J.

    1982-05-01

    This research is concerned with the frictional interactions at the toolwork interfaces in the machining and strip-drawing processes. A novel feature is that transparent sapphire (single crystal Al2O3) is being used as the tool and die material. This allows the tribological features of the interface to be directly observed and recorded on movie-film. These qualitative studies provide information on the role of lubricants. In addition, techniques are being developed to quantify the velocity gradient along the interface. For example, in the drawing work it has been found that tracer markings (e.g. dye-spots), applied to the undrawn strip, remain intact during drawing and can be tracked along the sapphire/strip interface. Such data will be used as input to a finite-element, elasto-plastic-workhardening model of the deformation process. The latter can compute strip deformation characteristics, drawing forces and local coefficients of friction at the interface. Introductory results will be presented in this paper, obtained from drawing tin-plated mild steel with sapphire and cemented carbide dies. Drawing loads and die-separating forces will be presented and movie-films of the action of tracer markings at the interface shown. In order to demonstrate how this data can be used in an analysis of a large strain deformation process with friction, initial results from running the FIPDEF elasto-plastic code will be discussed. From a commercial viewpoint research on strip-drawing is of special interest to the can-making industry. From a physical viewpoint stripdrawing is of particular interest because it is a symmetrical, plane strain deformation and, in comparison with other metal processing operations, it is more readily modeled. However, until now the elasto-plastic codes that have been developed to predictively model drawing have had limitations: the most notable being that of quantifying the friction conditions at the die-work interface. Hence the specification of the

  9. New neuro-fuzzy system-based holey polymer fibers drawing process

    Science.gov (United States)

    Mohammed Salim, Omar Nameer

    2017-10-01

    Furnace temperature (T), draw tension (TE), and draw ratio (Dr) are the main parameters that could directly affect holey polymer fiber (HPF) production during the drawing stage. Therefore, a suitable mechanism to control (T), (TE), and (Dr) is required to enhance the HPF production process. The conventional approaches, such as observation and tuning technique, experience many difficulties in realizing the accurate values of (T), (TE), and (Dr) in addition to being expensive and time consuming. Therefore, an artificial intelligence model using the adaptive neuro-fuzzy system (ANFIS) method is proposed as an effective solution to achieve an accurate value of the main parameters that affect HPF drawing. Three ANFIS models are developed and tested to determine which one has the best performance for emulating the operation of HPF drawing tower. The ANFIS model with a gbell MF provides a better performance than Gaussian MF ANFIS model and triangular MF ANFIS model in terms of lower mean absolute error and mean square error. Furthermore, the proposed gbell MF model achieved the highest Q-Q response, which indicates the excellent performance of this model.

  10. Experimental and Numerical Studies on Isothermal and Non-isothermal Deep Drawing of IS 513 CR3 Steel Sheets

    Science.gov (United States)

    Mayavan, T.; Karthikeyan, L.; Senthilkumar, V. S.

    2016-11-01

    The present work aims to investigate the effects of the temperature gradient developed within the tool profiles on the formability of IS 513 CR3-grade steel sheets using the cup drawing test. The deformation characteristics of steel sheets were analyzed by comparing the thicknesses in various regions of the formed cup and also the limiting drawing ratios (LDR). Finite element simulations were carried out to predict the behavior of the steel sheets in isothermal and non-isothermal forming using Abaqus/Standard 6.12-1. An analytical model created by Kim was used to validate the experimental and finite element analysis (FEA) results on identical process parameters. Both the FEA and analytical modeling results showed that formability improvement is possible in warm forming; the findings are in good agreement with the experimental results in determining the locations and values of excessive thinning. The results also indicated that formability improvement cannot be achieved by keeping the tooling temperature at the same level. The LDR increased by around 9.5% in isothermal forming and by 19% in non-isothermal forming (with the punch maintained at a lower temperature compared with the die and blank holder). In addition, the fractured surfaces of unsuccessfully formed samples were analyzed using scanning electron microscopy. Metallographic investigations confirmed that the fracture mechanism during the forming of IS 513 CR3-grade steel sheets depends on the brittleness, strain hardening value, forming temperature, and magnitude of stresses developed.

  11. Influence of a cold deformation process by drawing on the electrical properties of copper wires

    Directory of Open Access Journals (Sweden)

    Rafael da Silva Bernardo

    Full Text Available Abstract This article presents a study of the drawing, deformation, hardening and heat treatment of copper wire, in order to investigate the influence of combinations of operating variables (annealing factor, oil emulsion temperature and machine speed during the drawing process on the electrical conductivity of copper wires. The results showed that when the metal is deformed, the value of electrical conductivity suffers a decrease due to the hardening phenomenon. Because of this, it is necessary to heat treat the material. So, it was observed that the annealing factor, which is associated with the thermal treatment temperature, showed a high degree of correlation with the electrical conductivity. This fact is explained by the annealing factor which is responsible for the intensity of the heat treatment. The speed at which the drawing occurs also showed a direct correlation with electric conductivity because the higher the value, the greater the heat treatment temperature and consequently, the greater the electrical conductivity of the material. On the other hand, it had not been possible to establish a conclusion about the correlation between the electrical conductivity and oil emulsion temperature during the drawing process.

  12. Microsoft excel's automatic data processing and diagram drawing of RIA internal quality control parameters

    International Nuclear Information System (INIS)

    Zeng Pingfan; Liu Guoqiang

    2006-01-01

    We did automatic data processing and diagram drawing of various parameters of RIA' s internal quality control (IQC)by the use of Microsoft Excel (ME). By use of AVERAGE and STDEV of ME, we got x-bar, s and CV%. With pearson, we got the serum quality control coefficients (r). Inputing the original data to diagram's self-definition item, the diagram was drawn automatically. By the use of logic judging, we got the quality control judging results with the status, timing and data of various quality control parameters. For the past four years, the ME data processing and diagram drawing as well as quality control judging have been showed to be accurate, convenient and correct. It was quick and easy to manage and the automatic computer processing of RIA's IQC was realized. Conclusion: the method is applicable to all types of RIA' s IQC. (authors)

  13. Material Behavior Based Hybrid Process for Sheet Draw-Forging Thin Walled Magnesium Alloys

    International Nuclear Information System (INIS)

    Sheng, Z.Q.; Shivpuri, R.

    2005-01-01

    Magnesium alloys are conventionally formed at the elevated temperatures. The thermally improved formability is sensitive to the temperature and strain rate. Due to limitations in forming speeds, tooling strength and narrow processing windows, complex thin walled parts cannot be made by traditional warm drawing or hot forging processes. A hybrid process, which is based on the deformation mechanism of magnesium alloys at the elevated temperature, is proposed that combines warm drawing and hot forging modes to produce an aggressive geometry at acceptable forming speed. The process parameters, such as temperatures, forming speeds etc. are determined by the FEM modeling and simulation. Sensitivity analysis under the constraint of forming limits of Mg alloy sheet material and strength of tooling material is carried out. The proposed approach is demonstrated on a conical geometry with thin walls and with bottom features. Results show that designed geometry can be formed in about 8 seconds, this cannot be formed by conventional forging while around 1000s is required for warm drawing. This process is being further investigated through controlled experiments

  14. Parallel Distributed Processing theory in the age of deep networks

    OpenAIRE

    Bowers, Jeffrey

    2017-01-01

    Parallel Distributed Processing (PDP) models in psychology are the precursors of deep networks used in computer science. However, only PDP models are associated with two core psychological claims, namely, that all knowledge is coded in a distributed format, and cognition is mediated by non-symbolic computations. These claims have long been debated within cognitive science, and recent work with deep networks speaks to this debate. Specifically, single-unit recordings show that deep networks le...

  15. Research on the drawing process with a large total deformation wires of AZ31 alloy

    International Nuclear Information System (INIS)

    Bajor, T; Muskalski, Z; Suliga, M

    2010-01-01

    Magnesium and their alloys have been extensively studied in recent years, not only because of their potential applications as light-weight engineering materials, but also owing to their biodegradability. Due to their hexagonal close-packed crystallographic structure, cold plastic processing of magnesium alloys is difficult. The preliminary researches carried out by the authors have indicated that the application of the KOBO method, based on the effect of cyclic strain path change, for the deformation of magnesium alloys, provides the possibility of obtaining a fine-grained structure material to be used for further cold plastic processing with large total deformation. The main purpose of this work is to present research findings concerning a detailed analysis of mechanical properties and changes occurring in the structure of AZ31 alloy wire during the multistage cold drawing process. The appropriate selection of drawing parameters and the application of multistep heat treatment operations enable the deformation of the AZ31 alloy in the cold drawing process with a total draft of about 90%.

  16. Deep processes in non-relativistic confining potentials

    International Nuclear Information System (INIS)

    Fishbane, P.M.; Grisaru, M.T.

    1978-01-01

    The authors study deep inelastic and hard scattering processes for non-relativistic particles confined in deep potentials. The mechanisms by which the effects of confinement disappear and the particles scatter as if free are useful in understanding the analogous results for a relativistic field theory. (Auth.)

  17. Parallel Distributed Processing Theory in the Age of Deep Networks.

    Science.gov (United States)

    Bowers, Jeffrey S

    2017-12-01

    Parallel distributed processing (PDP) models in psychology are the precursors of deep networks used in computer science. However, only PDP models are associated with two core psychological claims, namely that all knowledge is coded in a distributed format and cognition is mediated by non-symbolic computations. These claims have long been debated in cognitive science, and recent work with deep networks speaks to this debate. Specifically, single-unit recordings show that deep networks learn units that respond selectively to meaningful categories, and researchers are finding that deep networks need to be supplemented with symbolic systems to perform some tasks. Given the close links between PDP and deep networks, it is surprising that research with deep networks is challenging PDP theory. Copyright © 2017. Published by Elsevier Ltd.

  18. Understanding human visual processing with Deep Neural Networks

    OpenAIRE

    Thorat, Sushrut

    2016-01-01

    This presentation has 2 parts:1. An introduction to the vision processing - neuroscience, and machine vision.2. Discussion of one of the first papers relating Deep Networks to the visual ventral stream. (Khaligh-Razavi, 2014)

  19. Multiple production of hadrons in deep inelastic processes

    International Nuclear Information System (INIS)

    Kiselev, A.V.; Petrov, V.A.

    1985-01-01

    Formulas are proposed for the description of the mean multiplicity of hadrons in deep inelastic processes. On the basis of the existing data, predictions are made for the behavior of the mean multiplicity at higher energies

  20. Average multiplications in deep inelastic processes and their interpretation

    International Nuclear Information System (INIS)

    Kiselev, A.V.; Petrov, V.A.

    1983-01-01

    Inclusive production of hadrons in deep inelastic proceseseus is considered. It is shown that at high energies the jet evolution in deep inelastic processes is mainly of nonperturbative character. With the increase of a final hadron state energy the leading contribution to an average multiplicity comes from a parton subprocess due to production of massive quark and gluon jets and their further fragmentation as diquark contribution becomes less and less essential. The ratio of the total average multiplicity in deep inelastic processes to the average multiplicity in e + e - -annihilation at high energies tends to unity

  1. Auditory processing during deep propofol sedation and recovery from unconsciousness

    OpenAIRE

    Koelsch, Stefan; Heinke, Wolfgang; Sammler, Daniela; Olthoff, Derk

    2006-01-01

    Objective Using evoked potentials, this study investigated effects of deep propofol sedation, and effects of recovery from unconsciousness, on the processing of auditory information with stimuli suited to elicit a physical MMN, and a (music-syntactic) ERAN. Methods Levels of sedation were assessed using the Bispectral Index (BIS) and the Modified Observer's Assessment of Alertness and Sedation Scale (MOAAS). EEG-measurements were performed during wakefulness, deep propofol sedation (MOAAS 2–3...

  2. A Study on Changes in Thickness of STS304 Material in the Progressive Drawing Process

    Directory of Open Access Journals (Sweden)

    Lee C.K.

    2017-06-01

    Full Text Available In the drawing process, the roundness of corners in the punch and the die are very important factors in determining the thicknesses of the product. The results clearly revealed that the thickness of a flange was increased and the thickness of body parts reduced when the roundness of the die entrance was small. The material thickness of the top part was decreased when the corner roundness of the punch was large. The smooth inflow of materials was found to have a significant effect on the thickness during the post-process. The compressive strength of STS 304 material exhibited a higher value compared with other processing methods. Moreover, we clearly observed the corner roundness of the punch and the die to be a very important factor for STS 304 materials.

  3. Draw-in Map - A Road Map for Simulation-Guided Die Tryout and Stamping Process Control

    International Nuclear Information System (INIS)

    Wang Chuantao; Zhang, Jimmy J.; Goan, Norman

    2005-01-01

    Sheet metal forming is a displacement or draw-in controlled manufacturing process in which a flat blank is drawn into die cavity to form an automotive body panel. Draw-in amount is the single most important stamping manufacturing index that controls all forming characteristics (strains, stresses, thinning, etc.), stamping failures (splits, wrinkles, surface distortion, etc.) and line die operations and automations. Draw-in Map is engineered for math-based die developments via advanced stamping simulation technology. Then the Draw-in Map is provided to die makers in plants as a road map for math-guided die tryout in which the die tryout workers follow the engineered tryout conditions and matches the engineered draw-in amount so that the tryout time and cost are greatly reduced, and quality is ensured. The Map can also be used as a math-based trouble-shooting tool to identify the causes of formability problems in stamping production. The engineered Draw-in Map has been applied to all draw die tryout for all GM vehicle programs since 1998. A minimum 50% reduction in both lead-time and cost and significant improvement in panel quality in tryout have been reported. This paper presents the concept and process to apply the engineered Draw-in Map in die tryout

  4. Drawing a Transductive Ecosophy in Process: Technological Arts, Residual Matter, Associated Milieus

    Directory of Open Access Journals (Sweden)

    Gisèle Trudel

    2015-06-01

    Full Text Available Drawing a Transductive Ecosophy in Process: Technological Arts, Residual Matter, Associated Milieus by Gisèle Trudel. NANO: New American Notes Online, Issue 7: The Aesthetics of Trash - nanocrit.com. This text examines the tetralogy of media artworks about residual matter produced by Ælab between 2008 and 2014. Taking its own title as a diagram (Deleuze and Guattari Mille Plateaux, it charts and builds on the processes of these artworks, elucidating their relations to materiality, philosophy and technicity. Technological research-creation becomes in these instances a transdisciplinary aesthetic act, emerging from an ecology of practices that combine humans, non-humans and waste matter in an effort to increase attentiveness in actions.

  5. A system of automated processing of deep water hydrological information

    Science.gov (United States)

    Romantsov, V. A.; Dyubkin, I. A.; Klyukbin, L. N.

    1974-01-01

    An automated system for primary and scientific analysis of deep water hydrological information is presented. Primary processing of the data in this system is carried out on a drifting station, which also calculates the parameters of vertical stability of the sea layers, as well as their depths and altitudes. Methods of processing the raw data are described.

  6. Privileging Younger Children's Voices in Research: Use of Drawings and a Co-Construction Process

    Directory of Open Access Journals (Sweden)

    Joanna Tay-Lim PhD Student

    2013-02-01

    Full Text Available The growing acknowledgement of the value of listening to children's views and experiences in social research, popularly termed as “listening to their voices,” brings with it methodological consequences. Regarding children as expert informants about their own lives carries with it the simultaneous call for researchers to be experts in developing and employing appropriate strategies that can effectively elicit the insights that children can bring to a research topic. With younger children, the use of participatory methodologies has been foregrounded as the key to unlocking their potential to contribute rich and useful perspectives to inform research into their lives. This article explores the usefulness of employing preschoolers' drawings within the context of a co-construction process to facilitate the children's construction of ideas and reinforce their voices in research. The case is made that the quality of the dialogical engagement is as important as the drawing itself, and both visual images and the verbal exchanges are central to the children's meaning-making process. In the co-construction process, both adult and child are (ideally equal players and the resulting dialogical process plays a major role in the constitution of the phenomena. The role of the researcher as the co-constructor can be a challenging one because it entails engaging and supporting children's views and the expression of these views. The discussion and illustrations from the first author's research projects contribute to the literature base on positioning preschool children as valid social actors in their communities. We operate through an ethos of empowerment of all participants, and aim for participatory research practice which has at its heart an active involvement in promoting the rights of children as citizens with voice and power. (Pascal & Bertram, 2009, p. 249

  7. Auditory processing during deep propofol sedation and recovery from unconsciousness.

    Science.gov (United States)

    Koelsch, Stefan; Heinke, Wolfgang; Sammler, Daniela; Olthoff, Derk

    2006-08-01

    Using evoked potentials, this study investigated effects of deep propofol sedation, and effects of recovery from unconsciousness, on the processing of auditory information with stimuli suited to elicit a physical MMN, and a (music-syntactic) ERAN. Levels of sedation were assessed using the Bispectral Index (BIS) and the Modified Observer's Assessment of Alertness and Sedation Scale (MOAAS). EEG-measurements were performed during wakefulness, deep propofol sedation (MOAAS 2-3, mean BIS=68), and a recovery period. Between deep sedation and recovery period, the infusion rate of propofol was increased to achieve unconsciousness (MOAAS 0-1, mean BIS=35); EEG measurements of recovery period were performed after subjects regained consciousness. During deep sedation, the physical MMN was markedly reduced, but still significant. No ERAN was observed in this level. A clear P3a was elicited during deep sedation by those deviants, which were task-relevant during the awake state. As soon as subjects regained consciousness during the recovery period, a normal MMN was elicited. By contrast, the P3a was absent in the recovery period, and the P3b was markedly reduced. Results indicate that the auditory sensory memory (as indexed by the physical MMN) is still active, although strongly reduced, during deep sedation (MOAAS 2-3). The presence of the P3a indicates that attention-related processes are still operating during this level. Processes of syntactic analysis appear to be abolished during deep sedation. After propofol-induced anesthesia, the auditory sensory memory appears to operate normal as soon as subjects regain consciousness, whereas the attention-related processes indexed by P3a and P3b are markedly impaired. Results inform about effects of sedative drugs on auditory and attention-related mechanisms. The findings are important because these mechanisms are prerequisites for auditory awareness, auditory learning and memory, as well as language perception during anesthesia.

  8. The Analysis of the High Speed Wire Drawing Process of High Carbon Steel Wires Under Hydrodynamic Lubrication Conditions

    Directory of Open Access Journals (Sweden)

    Suliga M.

    2015-04-01

    Full Text Available In this work the analysis of the wire drawing process in hydrodynamic dies has been done. The drawing process of φ5.5 mm wire rod to the final wire of φ1.7 mm was conducted in 12 passes, in drawing speed range of 5-25 m/s. For final wires of φ1.7 mm the investigation of topography of wire surface, the amount of lubricant on the wire surface and the pressure of lubricant in hydrodynamic dies were determined. Additionally, in the work selected mechanical properties of the wires have been estimated.

  9. The Analysis of Force Parameters in Drawing Process of High Carbon Steel Wires in Conventional and Hydrodynamic Dies

    Directory of Open Access Journals (Sweden)

    Suliga M.

    2017-12-01

    Full Text Available The paper analyzes force parameters in the process of multistage drawing of steel wires in conventional and hydrodynamic dies. The drawing process of the wire rod with a diameter of 5.5 mm for wires with a diameter of 1.70 mm was performed in 12 drafts with the usage of the multistage drawbench Koch KGT with the speed range of 5-25 m/s.

  10. Charm production and mass scales in deep inelastic processes

    International Nuclear Information System (INIS)

    Close, F.E.; Scott, D.M.; Sivers, D.

    1976-07-01

    Because of their large mass, the production of charmed particles offers the possibility of new insight into fundamental dynamics. An approach to deep inelastic processes is discussed in which Generalized Vector Meson Dominance is used to extend parton model results away from the strict Bjorken scaling limit into regions where mass scales play an important role. The processes e + e - annihilation, photoproduction, deep inelastic leptoproduction, photon-photon scattering and the production of lepton pairs in hadronic collisions are discussed. The GCMD approach provides a reasonably unified framework and makes specific predictions concerning the way in which these reactions reflect an underlying flavour symmetry, broken by large mass differences. (author)

  11. Influence of Surface-profile and Movement-path of Roller on Thickness Thinning during Multi-pass Deep Drawing Spinning

    Directory of Open Access Journals (Sweden)

    Xia Qinxiang

    2016-01-01

    Full Text Available Over thinning is a serious defect influencing the forming quality of spun workpiece during multi-pass deep drawing spinning. Surface-profile and movement-path of roller are the key factors influencing the thinning ratio of wall thickness of spun workpiece. The influence of surface-profile and movement-path of roller on thickness thinning were studied based on numerical simulation and experimental research, four groups of forming experiments were carried out under the combination of the different surface-profile of roller (R12 and R25-12 and movement-path of roller (spinning from the bottom of the blank and spinning from the middle of the blank. The results show that both the surface-profile and movement-path of roller have great influence on wall thickness thinning during multi-pass deep drawing spinning; and compared with the movement-path of roller, the influence of surface-profile of roller is more significant. The experimental results conform well to the simulation ones. It indicates that the FEA model established is reasonable and reliable.

  12. An Action Research on Deep Word Processing Strategy Instruction

    Science.gov (United States)

    Zhang, Limei

    2010-01-01

    For too long a time, how to memorize more words and keep them longer in mind has been a primary and everlasting problem for vocabulary teaching and learning. This study focused on deep processing as a word memorizing strategy in contextualizing, de- and re- contextualizing learning stages. It also examined possible effects of such pedagogy on…

  13. Some comments about polarization in deep inelastic processes

    International Nuclear Information System (INIS)

    Bajpai, R.P.

    1983-01-01

    One can fit baryon production in deep inelastic processes in terms of baryon fragmentation functions. It appears that for z > 0.3, the individual quark materializes into a baryon by picking up the appropriate diquark. The spin and isospin properties of the diquark will give definite asymmetry in baryon production in terms of only three unknown parameters. 4 references, 1 table

  14. Drawing Inventors

    Science.gov (United States)

    Szekely, George

    2012-01-01

    Children are drawing inventors. Their art is certainly not what most adults think of as drawing. Almost instinctively, kids know that drawing is everywhere--that they can draw with almost anything, and that innumerable surfaces can be converted for art use. Teaching drawing is showing interest and enthusiasm for kids' drawing inventions--instead…

  15. Local processing enhancements associated with superior observational drawing are due to enhanced perceptual functioning, not weak central coherence.

    Science.gov (United States)

    Chamberlain, Rebecca; McManus, I C; Riley, Howard; Rankin, Qona; Brunswick, Nicola

    2013-01-01

    Individuals with drawing talent have previously been shown to exhibit enhanced local visual processing ability. The aim of the current study was to assess whether local processing biases associated with drawing ability result from a reduced ability to cohere local stimuli into global forms, or an increased ability to disregard global aspects of an image. Local and global visual processing ability was assessed in art students and controls using the Group Embedded Figures Task, Navon shape stimuli, the Block Design Task and the Autism Spectrum Quotient, whilst controlling for nonverbal IQ and artistic ability. Local processing biases associated with drawing appear to arise from an enhancement of local processing alongside successful filtering of global information, rather than a reduction in global processing. The relationship between local processing and drawing ability is independent of individual differences in nonverbal IQ and artistic ability. These findings have implications for bottom-up and attentional theories of observational drawing, as well as explanations of special skills in autism.

  16. Guidelines for Selecting Plugs Used in Thin-Walled Tube Drawing Processes of Metallic Alloys

    Directory of Open Access Journals (Sweden)

    Eva María Rubio

    2017-12-01

    Full Text Available In this paper, some practical guidelines to select the plug or set of plugs more adequate to carry out drawing processes of thin-walled tubes carried out with fixed conical inner plug are presented. For this purpose, the most relevant input parameters have been considered in this study: the tube material, the most important geometrical parameters of the process (die semiangle, α , and cross-sectional area reduction, r and the friction conditions (Coulomb friction coefficients, μ 1 , between the die and the tube outer surface, and μ 2 , between the plug and the tube inner surface. Three work-hardening materials are analyzed: the annealed copper UNS C11000, the aluminum UNS A91100, and the stainless steel UNS S34000. The analysis is realized by means of the upper bound method (UBM, modelling the plastic deformation zone by triangular rigid zones (TRZ, under the validated assumption that the process occurs under plane strain conditions. The obtained results allow establishing, for each material, a group of geometrical parameters, friction conditions, a set of plugs that make possible to carry out the process under good conditions, and the optimum plug to carry out the process using the minimum amount of energy. The proposed model is validated by means of an own finite element analysis (FEA carried out under different conditions and, in addition, by other finite element method (FEM simulations and real experiments taken from other researchers found in the literature (called literature simulations and literature experimental results, respectively. As a main conclusion, it is possible to affirm that the plug that allows carrying out the process with minimum quantity of energy is cylindrical in most cases.

  17. Dispersal from deep ocean sources: physical and related scientific processes

    International Nuclear Information System (INIS)

    Robinson, A.R.; Kupferman, S.L.

    1985-02-01

    This report presents the results of the workshop ''Dispersal from Deep Ocean Sources: Physical and Related Scientific Processes,'' together with subsequent developments and syntheses of the material discussed there. The project was undertaken to develop usable predictive descriptions of dispersal from deep oceanic sources. Relatively simple theoretical models embodying modern ocean physics were applied, and observational and experimental data bases were exploited. All known physical processes relevant to the dispersal of passive, conservative tracers were discussed, and contact points for inclusion of nonconservative processes (biological and chemical) were identified. Numerical estimates of the amplitude, space, and time scales of dispersion were made for various mechanisms that control the evolution of the dispersal as the material spreads from a bottom point source to small-, meso-, and world-ocean scales. Recommendations for additional work are given. The volume is presented as a handbook of dispersion processes. It is intended to be updated as new results become available

  18. Effects due to spectator interaction in deep inelastic processes

    International Nuclear Information System (INIS)

    Smilga, A.V.

    1979-01-01

    The simplest diagrams describing interaction with the spectator in the e - π→e - + hadrons deep inelastic process are considered. The contribution of the final state interaction diagram to the structure function considerable in the Feynman gauge is suppressed under the temporal gauge choice in accordance with the results of the naive parton model. The expressin for the cross section of the process when large quark momentum is transferred to the spectator is derived

  19. Influence of the Strain History on TWIP Steel Deformation Mechanisms in the Deep-Drawing Process

    Science.gov (United States)

    Lapovok, R.; Timokhina, I.; Mester, A.-K.; Weiss, M.; Shekhter, A.

    2018-06-01

    A study of preferable deformation modes on strain path and strain level in a TWIP steel sheet was performed. Different strain paths were obtained by stretch forming of specimens with various shapes and tensile tests. TEM analysis was performed on samples cut from various locations in the deformed specimens, which had different strain paths and strain levels and the preferable deformation modes were identified. Stresses caused by various strain paths were considered and an analytical analysis performed to identify the preferable deformation modes for the case of single crystal. For a single crystal, in assumption of the absence of lattice rotation, the strain path and the level of accumulated equivalent strain define the preferable deformation mode. For a polycrystalline material, such analytical analysis is not possible due to the large number of grains and, therefore, numerical simulation was employed. For the polycrystalline material, the role of strain path diminishes due to the presence of a large number of grains with random orientations and the effect of accumulated strain becomes dominant. However, at small strains the strain path still defines the level of twinning activity. TEM analysis experimentally confirmed that various deformation modes lead to different deformation strengthening mechanisms.

  20. Encountering Drawing

    Science.gov (United States)

    Gregory, Nuala

    2017-01-01

    This article divides into two roughly equal parts, both of which aim to address the "act" rather than the "art" of drawing. The second part focuses on a theoretical discussion of drawing. The first bears on a number of themes including the role of drawing in colonial history, drawing and data collection, and drawing and memory.…

  1. Role of deep inelastic processes in nuclear physics: experimental and theoretical aspects of deep inelastic reactions

    International Nuclear Information System (INIS)

    Moretto, L.G.

    1979-03-01

    The collective modes excited in deep-inelastic reactions and their natural hierarchy provided by their characteristic relaxation times is described. The relaxation of the mass asymmetry mode is discussed in terms of a diffusion process. Charge distributions and angular distributions as a function of Z calculated with this model are in good agreement with experimental data. This diffusion model also treats the transfer of energy and angular momentum in terms of particle transfer, and is successfully compared with experimental γ-ray multiplicities as a function of both Q-value and mass asymmetry. The angular momentum transfer is again considered in connection with the sequential fission of heavy, deep-inelastic fragments and the excitation of collective modes in the exit channel is considered. The role of the giant E1 mode in the equilibration of the neutron-to-proton ratio is discussed. 39 references

  2. Deep inelastic processes. Phenomenology. Quark-parton model

    International Nuclear Information System (INIS)

    Ioffe, B.L.; Lipatov, L.N.; Khoze, V.A.

    1983-01-01

    Main theoretical approaches and experimental results related to deep inelastic processes are systematically outlined: electroproduction, neutrino scattering on nucleon, electron-positron pairs annihilation into hadron γγ collisions, production of lepton pairs in hadron collisions with a large effective mass or hadrons with large transverse momenta. Kinematics and phenomenology, space-time description of deep inelastic processes, sum rules, parton and quark-parton models are considered. The experiment is briefly discussed in the book. It is performed from the stand point of comparing it with the theory, experimental data are given as of June, 1982. Since the time of accomplishing the study on the manuscript a number of new experimental results not changing however the statements made in the book appeared. Principal consists in experiments with colliding proton-antiproton beams in CERN, which resulted in discovery of intermediate W-bozon

  3. Hadronic final states and sum rules in deep inelastic processes

    International Nuclear Information System (INIS)

    Pal, B.K.

    1977-01-01

    In order to get maximum information on the hadronic final states and sum rules in deep inelastic processes, Regge phenomenology and quarks parton model have been used. The unified picture for the production of hadrons of type i as a function of Bjorken and Feyman variables with only one adjustable parameter is formulated. The results of neutrino experiments and the production of charm particles are discussed in sum rules. (author)

  4. Multifilamentary MgB2 wires fracture behavior during the drawing process

    International Nuclear Information System (INIS)

    Shan, D.; Yan, G.; Zhou, L.; Li, J.S.; Li, C.S.; Wang, Q.Y.; Xiong, X.M.; Jiao, G.F.

    2012-01-01

    The fracture behavior of 6 + 1 filamentary MgB 2 superconductive wires is presented here. The composite wires were fabricated by in situ Powder-in-Tube method using Nb as a barrier and copper as a stabilizer. The microstructure of the material has a great influence on its fracture behavior. The microstructural aspects of crack nucleation and propagation are discussed. It shows that there are complicated correlations between fracture behavior and the main influencing parameters, which contain specific drawing conditions (drawing velocity, reduction in area per pass), materials properties (strength, yield stress, microstructure) as well as the extent of bonding between the metal sheaths at their interface.

  5. Thinking Drawing

    Science.gov (United States)

    Adams, Eileen

    2017-01-01

    This article draws heavily on the author's critical autobiography: "Eileen Adams: Agent of Change." It presents evidence of the value of drawing as a medium for learning, particularly in art and design, and argues that drawing is a useful educational tool. The premise is that drawing makes you think. This article explains various…

  6. Drawing images or Architectural drawing

    Directory of Open Access Journals (Sweden)

    Amparo Bernal López-Sanvicente

    2013-10-01

    Full Text Available In this article we will discuss how the aesthetic values, that the digital imaging provide, has influenced in drawing and architecture in a historical reading of the evolution of each means of architecture expression. In painting art and photography have been happening genres and styles that have adopted criteria of one or another discipline. When photography became independent from painting as an artistic discipline, its relationship to the architecture affected both the acceptance of its stylistic canon and the broadcast area. With technological development and the emergence of the new concept of digital imaging, it has become an indispensable tool in the whole process of contemporary architecture, which should not contaminate the true sense of the architectural drawing.

  7. An integrated CAD/CAM system for CNG pressure vessel manufactured by deep drawing and ironing operation

    Energy Technology Data Exchange (ETDEWEB)

    Park, Joon Hong; Kim, Chul; Choi, Jae Chan [Pusan National Univ., Pusan (Korea, Republic of)

    2004-06-01

    The fiber reinforced composite material is widely used in the multi-industrial field because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage proceeding to the sudden bursting which is generated by the pressure leakage condition. Therefore, pressure vessels using this composite material can be applied in the field such as defence industry and aerospace industry. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding of composite vessel subjected to internal pressure, the standard interpretation model is developed by using the ANSYS with AutoLISP and ANSYS APDL languages, general commercial software, which is verified as useful characteristic of the solution. Among the modules of the system, both the process planning module for carrying out the process planning of filament wound composite pressure vessel and the autofrettage process module for obtaining higher residual stress will minimize trial and error and reduce the period for developing new products. The system can serve as a valuable system for experts and as a dependable training aid for beginners.

  8. An integrated CAD/CAM system for CNG pressure vessel manufactured by deep drawing and ironing operation

    International Nuclear Information System (INIS)

    Park, Joon Hong; Kim, Chul; Choi, Jae Chan

    2004-01-01

    The fiber reinforced composite material is widely used in the multi-industrial field because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage proceeding to the sudden bursting which is generated by the pressure leakage condition. Therefore, pressure vessels using this composite material can be applied in the field such as defence industry and aerospace industry. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding of composite vessel subjected to internal pressure, the standard interpretation model is developed by using the ANSYS with AutoLISP and ANSYS APDL languages, general commercial software, which is verified as useful characteristic of the solution. Among the modules of the system, both the process planning module for carrying out the process planning of filament wound composite pressure vessel and the autofrettage process module for obtaining higher residual stress will minimize trial and error and reduce the period for developing new products. The system can serve as a valuable system for experts and as a dependable training aid for beginners

  9. Processing of chromatic information in a deep convolutional neural network.

    Science.gov (United States)

    Flachot, Alban; Gegenfurtner, Karl R

    2018-04-01

    Deep convolutional neural networks are a class of machine-learning algorithms capable of solving non-trivial tasks, such as object recognition, with human-like performance. Little is known about the exact computations that deep neural networks learn, and to what extent these computations are similar to the ones performed by the primate brain. Here, we investigate how color information is processed in the different layers of the AlexNet deep neural network, originally trained on object classification of over 1.2M images of objects in their natural contexts. We found that the color-responsive units in the first layer of AlexNet learned linear features and were broadly tuned to two directions in color space, analogously to what is known of color responsive cells in the primate thalamus. Moreover, these directions are decorrelated and lead to statistically efficient representations, similar to the cardinal directions of the second-stage color mechanisms in primates. We also found, in analogy to the early stages of the primate visual system, that chromatic and achromatic information were segregated in the early layers of the network. Units in the higher layers of AlexNet exhibit on average a lower responsivity for color than units at earlier stages.

  10. Mechanical drawing

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Ho Seon; Lee, Geun Hui

    2004-04-15

    This book deals with how to read and draw the mechanical drawing, which includes the basic of drawing like purpose, kinds, and criterion, projection, special projection drawing, omission of the figure, section, and types of section, dimensioning method, writing way of allowable limit size, tolerance of regular size, parts list and assembling drawing, fitting, mechanical elements like screw, key, pin, rivet, spring, bearing, pipe, valve, welding, geometric tolerance and mechanical materials.

  11. Multiple production of hadrons in deep-inelastic processes

    International Nuclear Information System (INIS)

    Kiselev, A.V.; Petrov, V.A.

    1984-01-01

    A formula to describe an average hadron multiplicity on deep-inelastic processes has been proposed. On the basis of available experimental data predictions are made about the behaviour of average multiplicity at higher energies. The W-dependence of obserVed in experiments at present remains invariable up to energies W approximately 20-25 GeV. At W> or approXimately 25 GeV there will begin a rapid ibcrease of , which is analogous to the increase, observed for sub(esup(+)esup(-)) and is of the same nature

  12. Motivational priming and processing interrupt: startle reflex modulation during shallow and deep processing of emotional words.

    Science.gov (United States)

    Herbert, Cornelia; Kissler, Johanna

    2010-05-01

    Valence-driven modulation of the startle reflex, that is larger eyeblinks during viewing of unpleasant pictures and inhibited blinks while viewing pleasant pictures, is well documented. The current study investigated, whether this motivational priming pattern also occurs during processing of unpleasant and pleasant words, and to what extent it is influenced by shallow vs. deep encoding of verbal stimuli. Emotional and neutral adjectives were presented for 5s, and the acoustically elicited startle eyeblink response was measured while subjects memorized the words by means of shallow or deep processing strategies. Results showed blink potentiation to unpleasant and blink inhibition to pleasant adjectives in subjects using shallow encoding strategies. In subjects using deep-encoding strategies, blinks were larger for pleasant than unpleasant or neutral adjectives. In line with this, free recall of pleasant words was also better in subjects who engaged in deep processing. The results suggest that motivational priming holds as long as processing is perceptual. However, during deep processing the startle reflex appears to represent a measure of "processing interrupt", facilitating blinks to those stimuli that are more deeply encoded. Copyright 2010 Elsevier B.V. All rights reserved.

  13. Ultrafine-Grained Pure Ti Processed by New SPD Scheme Combining Drawing with Shear

    Science.gov (United States)

    Raab, A. G.; Bobruk, E. V.; Raab, G. I.

    2018-05-01

    The paper displays the results of the studies and analysis of a promising severe plastic deformation scheme that implements the conditions of a non-monotonous impact during shear drawing of long-length bulk metal materials. The paper describes the efficiency of the proposed severe plastic deformation technique to form a gradient ultrafine-grained state in rod-shaped billets on the example of commercially pure Ti and its further development for future industrial applications.

  14. Reconsidering the scribbling stage of drawing: a new perspective on toddlers' representational processes

    Science.gov (United States)

    Longobardi, Claudio; Quaglia, Rocco; Iotti, Nathalie O.

    2015-01-01

    Although the scribbling stage of drawing has been historically regarded as meaningless and transitional, a sort of prelude to the “actual” drawing phase of childhood, recent studies have begun to re-evaluate this important moment of a child's development and find meaning in what was once considered mere motor activity and nothing more. The present study analyzes scribbling in all its subphases and discovers a clear intention behind young children's gestures. From expressing the dynamic qualities of an object and the child's relationship with it, to gradually reducing itself to a simple contour of a content no more “alive” on the paper, but only in the child's own imagination, we trace the evolution of the line as a tool that toddlers use to communicate feelings and intentions to the world that surrounds them. We will provide a selected number of graphical examples that are representative of our theory. These drawings (13 in total) were extracted from a much wider sample derived from our studies on children's graphical-pictorial abilities, conducted on children aged 0–3 years in various Italian nurseries. Our results appear to indicate that scribbling evolves through a series of stages, and that early graphical activity in children is sparked and maintained by their relationship with their caregivers and the desire to communicate with them. PMID:26347690

  15. Synthesis of magnetic nanoparticles as a draw solute in forward osmosis membrane process for the treatment of radioactive liquid waste

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Heeman; Lee, Kune Woo; Moon, Jei Kwon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-05-15

    These wastes contain about 0.3 ∼ 0.8 wt% of boric acid. It is known that reverse osmosis (RO) membrane can eliminate boron at high pH and boron of 40 ∼ 90% can be removed by RO membrane in pH condition. RO uses hydraulic pressure to oppose, and exceed, the osmotic pressure of an aqueous feed solution containing boric acid. As an emerging technology forward osmosis (FO) has attracted growing interest in wastewater treatment and desalination because FO operates at low or no hydraulic pressures. FO is a membrane process in which water flows across a semi-permeable membrane from a feed solution of lower osmotic pressure to a draw solution of higher osmotic pressure. However, the challenges of FO still lie in the fabrication of eligible FO membranes and the readily separable draw solutes of high osmotic pressures. Superparamagnetic Fe{sub 3}O{sub 4} nanoparticles can be separated from water by an external magnet field easily. If Fe{sub 3}O{sub 4} nanoparticles are coated with highly soluble organic substances, thus they can be used as a draw solute by concurrently generating high osmotic pressure and easy separation. The carboxylated polyglycerol coated Fe{sub 3}O{sub 4} nanoparticles have been successfully synthesized. The nanoparticles were about 50 nm in diameter and showed the good colloidal stability in aqueous solution. The osmolality and osmotic pressure were enough high to be used as a draw solute in FO. For the future work, we will investigate the performance of our magnetic draw solute in FO to remove boron in the simulated liquid waste.

  16. Synthesis of magnetic nanoparticles as a draw solute in forward osmosis membrane process for the treatment of radioactive liquid waste

    International Nuclear Information System (INIS)

    Yang, Heeman; Lee, Kune Woo; Moon, Jei Kwon

    2013-01-01

    These wastes contain about 0.3 ∼ 0.8 wt% of boric acid. It is known that reverse osmosis (RO) membrane can eliminate boron at high pH and boron of 40 ∼ 90% can be removed by RO membrane in pH condition. RO uses hydraulic pressure to oppose, and exceed, the osmotic pressure of an aqueous feed solution containing boric acid. As an emerging technology forward osmosis (FO) has attracted growing interest in wastewater treatment and desalination because FO operates at low or no hydraulic pressures. FO is a membrane process in which water flows across a semi-permeable membrane from a feed solution of lower osmotic pressure to a draw solution of higher osmotic pressure. However, the challenges of FO still lie in the fabrication of eligible FO membranes and the readily separable draw solutes of high osmotic pressures. Superparamagnetic Fe 3 O 4 nanoparticles can be separated from water by an external magnet field easily. If Fe 3 O 4 nanoparticles are coated with highly soluble organic substances, thus they can be used as a draw solute by concurrently generating high osmotic pressure and easy separation. The carboxylated polyglycerol coated Fe 3 O 4 nanoparticles have been successfully synthesized. The nanoparticles were about 50 nm in diameter and showed the good colloidal stability in aqueous solution. The osmolality and osmotic pressure were enough high to be used as a draw solute in FO. For the future work, we will investigate the performance of our magnetic draw solute in FO to remove boron in the simulated liquid waste

  17. Early Detection of Alzheimer's Disease Based on the Patient's Creative Drawing Process: First Results with a Novel Neuropsychological Testing Method.

    Science.gov (United States)

    Heymann, Petra; Gienger, Regine; Hett, Andreas; Müller, Stephan; Laske, Christoph; Robens, Sibylle; Ostermann, Thomas; Elbing, Ulrich

    2018-01-01

    Based on the knowledge of art therapy, we developed a new neuropsychological drawing test in order to identify individuals with mild cognitive impairment (MCI) as well as dementia patients and healthy controls (HC). By observing a variety of drawing characteristics of 92 participants with a mean age of 67.7, art therapy and dementia experts discriminate HC from MCI, early dementia of the Alzheimer-type (eDAT), and moderate dementia of the Alzheimer-type (mDAT) by the process analysis of tree drawings on a digitizing tablet. The art therapist's average categorical rating of healthy and MCI or demented individuals matched the clinical diagnosis by 88%. In a first small study, we analyzed interrater reliability, sensitivity, specificity, negative and positive predicted values of our tree drawing test (TDT) in comparison with the clock drawing test (CDT). Similar values of moderate interrater reliability were found for the TDT (0.56) as well as for the CDT (0.54). A significant high sensitivity of 0.9 within this binary impairment scale (HC versus impaired or demented) can be demonstrated. Substantial values for the specificity (0.67) could be obtained that however remain under a perfect value of the CDT (1.0). Considering 31 individuals that received the clinical diagnosis "impaired or demented" the TDT shows a higher recognition rate for the MCI group than the CDT. Furthermore in 8 of 12 borderline cases of clinical diagnosis, the outcome of the TDT diagnosis was consistent with the final clinical result.

  18. The deep processing of oil residues conjunction with shales

    Directory of Open Access Journals (Sweden)

    Anatoly Maloletnev

    2012-12-01

    Full Text Available The results of studies on the development of a new process of thermal cracking of tar oil as a slurry with crushed oil shale to obtain components of motor fuels. The results suggest doubtless advantages of the process before the industrial of thermo cracking, since the single-stage processing of raw materials in relatively in the mild conditions (5 MPa, 425ºC, volumetric feed rate 1.0 h-1 is achieved deep destruction of tar oil (the yield petrol fraction with a bp amounts to up to 180ºC - ~12 mass % of middle distillates with a bp 180-360ºC – 43-44 mass %, of raw material for catalytic cracking of a bp 360-520ºC – ~15-16%, based on the initial tar oil. Formed like coke products and raw materials contained in V and Ni is postponed on the mineral part of slate and removed from the reaction zone with the liquid products of the process.

  19. Modeling and Control of the Springback Effect in the Bottom Sheet Metal Part One-Stage Drawing Process

    Directory of Open Access Journals (Sweden)

    A. S. Chumadin

    2014-01-01

    Full Text Available The main objective of this study is to reduce a manufacturing complexity of bottom sheet metal parts by improving the accuracy of parts produced. This study is aimed at using the finite element analysis to prove assumptions that there is a transition frontier between the processes of forming and drawing, and there are capabilities to control springback effect by moving this frontier positions.The process, the stress-strain state of which in the dome corresponds to the process of forming parts, and in the flange area to the drawing process, was considered to be a formingdrawing process.Based on previous studies, techniques to reduce a springback have been proposed which enable us to use three calculation schemes for the process simulation:The frontier transition position control between the processes of forming and drawing by changing the contact pressure on the flange by varying the frictions coefficients on the die and binder surfaces;Springback manage through the additional tensile forces in the flange area of the blank;Springback manage through the technological insert at the first process stage.For ease of comparison with previous research results the same geometric parameters and material properties of the items are used in the simulation.The springback analysis used a finite element method in the AutoFormTM incremental module with automatically mashed and standard tolerance computation properties. The blank, binder, punch, and die were then imported to the module by CATIATM interface in .iges format.The calculation has shown that the optimal value for the least thinning and springback parts are available for the second scheme whereby ring punch makes additional tension in the flange area (from 1.09 to 0.35 mm with thinning from 0.80 to 0.73 mm. The use of flange retention of sheet blank at the expense of variable frictional forces showed the springback value reduction by 4 times (from 1.09 to 0.27 mm. However thinning was 16% (from 0.80 to

  20. Elastocaloric effects in ultra-fine grained NiTi microwires processed by cold-drawing

    Directory of Open Access Journals (Sweden)

    Xuexi Zhang

    2018-03-01

    Full Text Available Efficient elastocaloric cooling in shape memory alloys requires a stable superelastic behavior in which high yield strength is needed. Here Ni50.4Ti49.6 microwires with diameter 130 μm and ultra-fine grains ∼30 nm were prepared by multi-step cold-drawing and low-temperature annealing. Enhanced cyclic stability of the elastocaloric effects induced by the superelastic training was demonstrated. The pre-trained microwire showed a stable ΔSe 43 J/(kg K with a broad working temperature range ΔT ∼ 70 K. The superelastic trained microwire, with giant and stable ΔSe over a wide working temperature window, may act as a promising elastocaloric cooling material for minor-sized devices.

  1. 3D Viscoelastic Finite Element Modelling of Polymer Flow in the Fiber Drawing Process for Microstructured Polymer Optical Fiber Fabrication

    DEFF Research Database (Denmark)

    Fasano, Andrea; Rasmussen, Henrik K.; Marín, J. M. R.

    2015-01-01

    The process of drawing an optical fiber from a polymer preform is still not completely understood,although it represents one of the most critical steps in the process chain for the fabrication of microstructuredpolymer optical fibers (mPOFs). Here we present a new approach for the numerical...... modelling of the fiber drawingprocess using a fully three-dimensional and time-dependent finite element method, giving significant insightinto this widely spread mPOF production technique. Our computational predictions are physically based on theviscoelastic fluid dynamics of polymers. Until now...

  2. A Non-catalytic Deep Desulphurization Process using Hydrodynamic Cavitation

    Science.gov (United States)

    Suryawanshi, Nalinee B.; Bhandari, Vinay M.; Sorokhaibam, Laxmi Gayatri; Ranade, Vivek V.

    2016-09-01

    A novel approach is developed for desulphurization of fuels or organics without use of catalyst. In this process, organic and aqueous phases are mixed in a predefined manner under ambient conditions and passed through a cavitating device. Vapor cavities formed in the cavitating device are then collapsed which generate (in-situ) oxidizing species which react with the sulphur moiety resulting in the removal of sulphur from the organic phase. In this work, vortex diode was used as a cavitating device. Three organic solvents (n-octane, toluene and n-octanol) containing known amount of a model sulphur compound (thiophene) up to initial concentrations of 500 ppm were used to verify the proposed method. A very high removal of sulphur content to the extent of 100% was demonstrated. The nature of organic phase and the ratio of aqueous to organic phase were found to be the most important process parameters. The results were also verified and substantiated using commercial diesel as a solvent. The developed process has great potential for deep of various organics, in general, and for transportation fuels, in particular.

  3. Architectural Drawing

    DEFF Research Database (Denmark)

    Steinø, Nicolai

    2018-01-01

    In a time of computer aided design, computer graphics and parametric design tools, the art of architectural drawing is in a state of neglect. But design and drawing are inseparably linked in ways which often go unnoticed. Essentially, it is very difficult, if not impossible, to conceive of a design...... is that computers can represent graphic ideas both faster and better than most medium-skilled draftsmen, drawing in design is not only about representing final designs. In fact, several steps involving the capacity to draw lie before the representation of a final design. Not only is drawing skills an important...... prerequisite for learning about the nature of existing objects and spaces, and thus to build a vocabulary of design. It is also a prerequisite for both reflecting and communicating about design ideas. In this paper, a taxonomy of notation, reflection, communication and presentation drawing is presented...

  4. Bad Drawing

    OpenAIRE

    Burgoyne, Greig

    2016-01-01

    "Only when we move do we see the chains" - Rosa Luxemburg Bad drawing / paper cell is a site-specific drawing performance commissioned for The Prison Drawing Project, Scarborough jail, Yorkshire, presented as a film grafted onto the space that is the cell. It takes the notion of drawing as an act of covering and form of measurement, in an immersive act of attempted liberation. Measuring using rolls of paper, the film chronicles what could be seen as a bad day wallpapering a space, no ass...

  5. Deep Levels of Processing Elicit a Distinctiveness Heuristic: Evidence from the Criterial Recollection Task

    Science.gov (United States)

    Gallo, David A.; Meadow, Nathaniel G.; Johnson, Elizabeth L.; Foster, Katherine T.

    2008-01-01

    Thinking about the meaning of studied words (deep processing) enhances memory on typical recognition tests, relative to focusing on perceptual features (shallow processing). One explanation for this levels-of-processing effect is that deep processing leads to the encoding of more distinctive representations (i.e., more unique semantic or…

  6. Combining shallow and deep processing for a robust, fast, deep-linguistic dependency parser

    OpenAIRE

    Schneider, G

    2004-01-01

    This paper describes Pro3Gres, a fast, robust, broad-coverage parser that delivers deep-linguistic grammatical relation structures as output, which are closer to predicate-argument structures and more informative than pure constituency structures. The parser stays as shallow as is possible for each task, combining shallow and deep-linguistic methods by integrating chunking and by expressing the majority of long-distance dependencies in a context-free way. It combines statistical and rule-base...

  7. Prize Draw

    CERN Multimedia

    Staff Association

    2014-01-01

      Prize draw Go Sport vouchers 393 members of the Staff Association participated in our free prize draw in July where they could win one of the thirty Go Sport vouchers of 50 euros. The thirty winners have been contacted and can come and collect their voucher from the Staff Association Secretariat.

  8. Analyzing the Effect of Spinning Process Variables on Draw Frame Blended Cotton Mélange Yarn Quality

    Science.gov (United States)

    Ray, Suchibrata; Ghosh, Anindya; Banerjee, Debamalya

    2017-12-01

    An investigation has been made to study the effect of important spinning process variables namely shade depth, ring frame spindle speed and yarn twist multiplier (TM) on various yarn quality parameters like unevenness, strength, imperfection, elongation at break and hairiness index of draw frame blended cotton mélange yarn. Three factors Box and Behnken design of experiment has been used to conduct the study. The quadratic regression model is used to device the statistical inferences about sensitivity of the yarn quality parameters to the different process variables. The response surfaces are constructed for depicting the geometric representation of yarn quality parameters plotted as a function of process variables. Analysis of the results show that yarn strength of draw frame blended cotton mélange yarn is significantly affected by shade depth and TM. Yarn unevenness is affected by shade depth and ring frame spindle speed. Yarn imperfection level is mainly influenced by the shade depth and spindle speed. The shade depth and yarn TM have shown significant impact on yarn hairiness index.

  9. Machine drawing

    CERN Document Server

    Narayana, KL; Reddy, K Venkata

    2006-01-01

    About the Book: Written by three distinguished authors with ample academic and teaching experience, this textbook, meant for diploma and degree students of Mechanical Engineering as well as those preparing for AMIE examination, incorporates the latest standards. The new edition includes the features of assembly drawings, part drawings and computer-aided drawings to cater to the needs of students pursuing various courses. The text of the new edition has been thoroughly revised to include new concepts and practices in the subject. It should prove an ideal textbook. Contents: Introduction

  10. Modulation of Human Time Processing by Subthalamic Deep Brain Stimulation

    Science.gov (United States)

    Timmermann, Lars; Reck, Christiane; Maarouf, Mohammad; Jörgens, Silke; Ploner, Markus; Südmeyer, Martin; Groiss, Stefan Jun; Sturm, Volker; Niedeggen, Michael; Schnitzler, Alfons

    2011-01-01

    Timing in the range of seconds referred to as interval timing is crucial for cognitive operations and conscious time processing. According to recent models of interval timing basal ganglia (BG) oscillatory loops are involved in time interval recognition. Parkinsońs disease (PD) is a typical disease of the basal ganglia that shows distortions in interval timing. Deep brain stimulation (DBS) of the subthalamic nucleus (STN) is a powerful treatment of PD which modulates motor and cognitive functions depending on stimulation frequency by affecting subcortical-cortical oscillatory loops. Thus, for the understanding of BG-involvement in interval timing it is of interest whether STN-DBS can modulate timing in a frequency dependent manner by interference with oscillatory time recognition processes. We examined production and reproduction of 5 and 15 second intervals and millisecond timing in a double blind, randomised, within-subject repeated-measures design of 12 PD-patients applying no, 10-Hz- and ≥130-Hz-STN-DBS compared to healthy controls. We found under(re-)production of the 15-second interval and a significant enhancement of this under(re-)production by 10-Hz-stimulation compared to no stimulation, ≥130-Hz-STN-DBS and controls. Milliseconds timing was not affected. We provide first evidence for a frequency-specific modulatory effect of STN-DBS on interval timing. Our results corroborate the involvement of BG in general and of the STN in particular in the cognitive representation of time intervals in the range of multiple seconds. PMID:21931767

  11. Modulation of human time processing by subthalamic deep brain stimulation.

    Science.gov (United States)

    Wojtecki, Lars; Elben, Saskia; Timmermann, Lars; Reck, Christiane; Maarouf, Mohammad; Jörgens, Silke; Ploner, Markus; Südmeyer, Martin; Groiss, Stefan Jun; Sturm, Volker; Niedeggen, Michael; Schnitzler, Alfons

    2011-01-01

    Timing in the range of seconds referred to as interval timing is crucial for cognitive operations and conscious time processing. According to recent models of interval timing basal ganglia (BG) oscillatory loops are involved in time interval recognition. Parkinsońs disease (PD) is a typical disease of the basal ganglia that shows distortions in interval timing. Deep brain stimulation (DBS) of the subthalamic nucleus (STN) is a powerful treatment of PD which modulates motor and cognitive functions depending on stimulation frequency by affecting subcortical-cortical oscillatory loops. Thus, for the understanding of BG-involvement in interval timing it is of interest whether STN-DBS can modulate timing in a frequency dependent manner by interference with oscillatory time recognition processes. We examined production and reproduction of 5 and 15 second intervals and millisecond timing in a double blind, randomised, within-subject repeated-measures design of 12 PD-patients applying no, 10-Hz- and ≥ 130-Hz-STN-DBS compared to healthy controls. We found under(re-)production of the 15-second interval and a significant enhancement of this under(re-)production by 10-Hz-stimulation compared to no stimulation, ≥ 130-Hz-STN-DBS and controls. Milliseconds timing was not affected. We provide first evidence for a frequency-specific modulatory effect of STN-DBS on interval timing. Our results corroborate the involvement of BG in general and of the STN in particular in the cognitive representation of time intervals in the range of multiple seconds.

  12. Drawing in nursing PBL.

    Science.gov (United States)

    Chan, Zenobia C Y

    2013-08-01

    The implementation of art education in nursing is said to have positive effects on nursing students. Most studies applied visual art dialogues or object design, whereas the effectiveness of drawing as a teaching and learning method is rarely examined and discussed. This paper aimed to discuss the potential and effectiveness of drawing as a learning and teaching method. Four drawings which were created by Hong Kong nursing students are demonstrated and the students' perspectives of how drawing enhanced learning are shown in this paper. Topics on drawing as a fun teaching and learning method and the way it can enhance critical thinking and creativity are also discussed. In conclusion, the activity was a great success, and students enjoyed the learning process and reflected positive comments. However, we cannot conclude that drawing is an effective teaching and learning method based on a single paper, therefore more similar studies should be conducted to investigate this method. Copyright © 2012 Elsevier Ltd. All rights reserved.

  13. Evolutionary process of deep-sea bathymodiolus mussels.

    Science.gov (United States)

    Miyazaki, Jun-Ichi; de Oliveira Martins, Leonardo; Fujita, Yuko; Matsumoto, Hiroto; Fujiwara, Yoshihiro

    2010-04-27

    Since the discovery of deep-sea chemosynthesis-based communities, much work has been done to clarify their organismal and environmental aspects. However, major topics remain to be resolved, including when and how organisms invade and adapt to deep-sea environments; whether strategies for invasion and adaptation are shared by different taxa or unique to each taxon; how organisms extend their distribution and diversity; and how they become isolated to speciate in continuous waters. Deep-sea mussels are one of the dominant organisms in chemosynthesis-based communities, thus investigations of their origin and evolution contribute to resolving questions about life in those communities. We investigated worldwide phylogenetic relationships of deep-sea Bathymodiolus mussels and their mytilid relatives by analyzing nucleotide sequences of the mitochondrial cytochrome c oxidase subunit I (COI) and NADH dehydrogenase subunit 4 (ND4) genes. Phylogenetic analysis of the concatenated sequence data showed that mussels of the subfamily Bathymodiolinae from vents and seeps were divided into four groups, and that mussels of the subfamily Modiolinae from sunken wood and whale carcasses assumed the outgroup position and shallow-water modioline mussels were positioned more distantly to the bathymodioline mussels. We provisionally hypothesized the evolutionary history of Bathymodilolus mussels by estimating evolutionary time under a relaxed molecular clock model. Diversification of bathymodioline mussels was initiated in the early Miocene, and subsequently diversification of the groups occurred in the early to middle Miocene. The phylogenetic relationships support the "Evolutionary stepping stone hypothesis," in which mytilid ancestors exploited sunken wood and whale carcasses in their progressive adaptation to deep-sea environments. This hypothesis is also supported by the evolutionary transition of symbiosis in that nutritional adaptation to the deep sea proceeded from extracellular

  14. Evolutionary process of deep-sea bathymodiolus mussels.

    Directory of Open Access Journals (Sweden)

    Jun-Ichi Miyazaki

    Full Text Available BACKGROUND: Since the discovery of deep-sea chemosynthesis-based communities, much work has been done to clarify their organismal and environmental aspects. However, major topics remain to be resolved, including when and how organisms invade and adapt to deep-sea environments; whether strategies for invasion and adaptation are shared by different taxa or unique to each taxon; how organisms extend their distribution and diversity; and how they become isolated to speciate in continuous waters. Deep-sea mussels are one of the dominant organisms in chemosynthesis-based communities, thus investigations of their origin and evolution contribute to resolving questions about life in those communities. METHODOLOGY/PRINCIPAL FINDING: We investigated worldwide phylogenetic relationships of deep-sea Bathymodiolus mussels and their mytilid relatives by analyzing nucleotide sequences of the mitochondrial cytochrome c oxidase subunit I (COI and NADH dehydrogenase subunit 4 (ND4 genes. Phylogenetic analysis of the concatenated sequence data showed that mussels of the subfamily Bathymodiolinae from vents and seeps were divided into four groups, and that mussels of the subfamily Modiolinae from sunken wood and whale carcasses assumed the outgroup position and shallow-water modioline mussels were positioned more distantly to the bathymodioline mussels. We provisionally hypothesized the evolutionary history of Bathymodilolus mussels by estimating evolutionary time under a relaxed molecular clock model. Diversification of bathymodioline mussels was initiated in the early Miocene, and subsequently diversification of the groups occurred in the early to middle Miocene. CONCLUSIONS/SIGNIFICANCE: The phylogenetic relationships support the "Evolutionary stepping stone hypothesis," in which mytilid ancestors exploited sunken wood and whale carcasses in their progressive adaptation to deep-sea environments. This hypothesis is also supported by the evolutionary transition of

  15. Automatic drawing and CAD actualization in processing data of radiant sampling in physics prospect

    International Nuclear Information System (INIS)

    Liu Jinsheng

    2010-01-01

    In this paper discussed a method of processing radiant sampling data with computer. By this method can get expain the curve of radiant sampling data, and we can combine mineral masses and analyse and calculate them, then record the result on Notebook. There are many merites of this method: easy to learn, simple to use, high efficient. It adapts to all sorts of mines. (authors)

  16. Automatic drawing and cad actualiztion in processing data of radiant sampling in physics prospect

    International Nuclear Information System (INIS)

    Liu Jinsheng

    2010-01-01

    In this paper discussed a method of processing radiant sampling data with computer. By this method can get explain the curve of radiant sampling data, and we can combine mineral masses and analyses and calculate them, then record the result on Notebook. There are many merites of this method: easy to learn, simple to use, high efficient. It adapts to all sorts of mines. (authors)

  17. Scratching the surface: the processing of pain from deep tissues.

    Science.gov (United States)

    Sikandar, Shafaq; Aasvang, Eske Kvanner; Dickenson, Anthony H

    2016-04-01

    Although most pain research focuses on skin, muscles, joints and viscerae are major sources of pain. We discuss the mechanisms of deep pains arising from somatic and visceral structures and how this can lead to widespread manifestations and chronification. We include how both altered peripheral and central sensory neurotransmission lead to deep pain states and comment on key areas such as top-down modulation where little is known. It is vital that the clinical characterization of deep pain in patients is improved to allow for back translation to preclinical models so that the missing links can be ascertained. The contribution of deeper somatic and visceral tissues to various chronic pain syndromes is common but there is much we need to know.

  18. Automated drawing generation system

    International Nuclear Information System (INIS)

    Yoshinaga, Toshiaki; Kawahata, Junichi; Yoshida, Naoto; Ono, Satoru

    1991-01-01

    Since automated CAD drawing generation systems still require human intervention, improvements were focussed on an interactive processing section (data input and correcting operation) which necessitates a vast amount of work. As a result, human intervention was eliminated, the original objective of a computerized system. This is the first step taken towards complete automation. The effects of development and commercialization of the system are as described below. (1) The interactive processing time required for generating drawings was improved. It was determined that introduction of the CAD system has reduced the time required for generating drawings. (2) The difference in skills between workers preparing drawings has been eliminated and the quality of drawings has been made uniform. (3) The extent of knowledge and experience demanded of workers has been reduced. (author)

  19. Improvements in anatomy knowledge when utilizing a novel cyclical "Observe-Reflect-Draw-Edit-Repeat" learning process.

    Science.gov (United States)

    Backhouse, Mark; Fitzpatrick, Michael; Hutchinson, Joseph; Thandi, Charankumal S; Keenan, Iain D

    2017-01-01

    Innovative educational strategies can provide variety and enhance student learning while addressing complex logistical and financial issues facing modern anatomy education. Observe-Reflect-Draw-Edit-Repeat (ORDER), a novel cyclical artistic process, has been designed based on cognitivist and constructivist learning theories, and on processes of critical observation, reflection and drawing in anatomy learning. ORDER was initially investigated in the context of a compulsory first year surface anatomy practical (ORDER-SAP) at a United Kingdom medical school in which a cross-over trial with pre-post anatomy knowledge testing was utilized and student perceptions were identified. Despite positive perceptions of ORDER-SAP, medical student (n = 154) pre-post knowledge test scores were significantly greater (P learning methods (3.26, SD = ±2.25) than with ORDER-SAP (2.17, ±2.30). Based on these findings, ORDER was modified and evaluated in the context of an optional self-directed gross anatomy online interactive tutorial (ORDER-IT) for participating first year medical students (n = 55). Student performance was significantly greater (P  0.05) to those students without these characteristics. These findings will be of value to anatomy instructors seeking to engage students from diverse learning backgrounds in a research-led, innovative, time and cost-effective learning method, in the context of contrasting learning environments. Anat Sci Educ 10: 7-22. © 2016 American Association of Anatomists. © 2016 American Association of Anatomists.

  20. Differential impact of thalamic versus subthalamic deep brain stimulation on lexical processing.

    Science.gov (United States)

    Krugel, Lea K; Ehlen, Felicitas; Tiedt, Hannes O; Kühn, Andrea A; Klostermann, Fabian

    2014-10-01

    Roles of subcortical structures in language processing are vague, but, interestingly, basal ganglia and thalamic Deep Brain Stimulation can go along with reduced lexical capacities. To deepen the understanding of this impact, we assessed word processing as a function of thalamic versus subthalamic Deep Brain Stimulation. Ten essential tremor patients treated with thalamic and 14 Parkinson׳s disease patients with subthalamic Deep Brain Stimulation performed an acoustic Lexical Decision Task ON and OFF stimulation. Combined analysis of task performance and event-related potentials allowed the determination of processing speed, priming effects, and N400 as neurophysiological correlate of lexical stimulus processing. 12 age-matched healthy participants acted as control subjects. Thalamic Deep Brain Stimulation prolonged word decisions and reduced N400 potentials. No comparable ON-OFF effects were present in patients with subthalamic Deep Brain Stimulation. In the latter group of patients with Parkinson' disease, N400 amplitudes were, however, abnormally low, whether under active or inactive Deep Brain Stimulation. In conclusion, performance speed and N400 appear to be influenced by state functions, modulated by thalamic, but not subthalamic Deep Brain Stimulation, compatible with concepts of thalamo-cortical engagement in word processing. Clinically, these findings specify cognitive sequels of Deep Brain Stimulation in a target-specific way. Copyright © 2014 Elsevier Ltd. All rights reserved.

  1. Drawing in architectural lighting design

    NARCIS (Netherlands)

    Skipetari, A.; Nijhuis, S.

    2011-01-01

    Drawing is an important tool for lighting designers. Not only as a means of visual communication but also to aid visual thinking. As a process and product, drawing is a constituent part of the overall lighting design process, from concept to realisation. The emphasis is usually placed on drawing as

  2. Increasing the Deep Drawability of Al-1050 Aluminum Sheet using Multi-Point Blank Holder

    Directory of Open Access Journals (Sweden)

    Gavas, M.

    2006-01-01

    Full Text Available Aluminum alloys have been widely used in the fields of automobile and aerospace industries. Due to their bad cold-formability in deep drawing, a lot of forming methods have been implemented to increase the drawing height and the limiting drawing rate (LDR. The conventional deep drawing process is limited to a certain limit drawing ratio beyond which failure will ensue. The purpose of this experimental study is to examine the possibilities of increasing this limitation using the multi-point blank holder. The results from the experiments showed that the multi-point blank holder is effective way to promote deep drawability of Al-1050 sheet.

  3. Drilling bits for deep drilling and process for their manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Rhode, H.; Juergens, R.; Feenstra, R.; Busking, B.E.

    1978-11-30

    The invention concerns a drilling head or a drilling bit for use in deep drilling in underground formations and particularly concerns a drilling bit with a drilling bit body, which has a shank and a hollow space, which is connected with a duct extending through the shank. The drilling bit body has several separate cutting elements for removing material from the floor of a borehole and hydraulic devices for cooling and/or cleaning the cutting elements are provided.

  4. An integrated architecture for shallow and deep processing

    OpenAIRE

    Crysmann, Berthold; Frank, Anette; Kiefer, Bernd; Müller, Stefan; Neumann, Günter; Piskorski, Jakub; Schäfer, Ulrich; Siegel, Melanie; Uszkoreit, Hans; Xu, Feiyu; Becker, Markus; Krieger, Hans-Ulrich

    2011-01-01

    We present an architecture for the integration of shallow and deep NLP components which is aimed at flexible combination of different language technologies for a range of practical current and future applications. In particular, we describe the integration of a high-level HPSG parsing system with different high-performance shallow components, ranging from named entity recognition to chunk parsing and shallow clause recognition. The NLP components enrich a representation of natural language te...

  5. Animated construction of line drawings

    KAUST Repository

    Fu, Hongbo; Zhou, Shizhe; Liu, Ligang; Mitra, Niloy J.

    2011-01-01

    Revealing the sketching sequence of a line drawing can be visually intriguing and used for video-based storytelling. Typically this is enabled based on tedious recording of artists' drawing process. We demonstrate that it is often possible

  6. Integrating deep and shallow natural language processing components : representations and hybrid architectures

    OpenAIRE

    Schäfer, Ulrich

    2006-01-01

    We describe basic concepts and software architectures for the integration of shallow and deep (linguistics-based, semantics-oriented) natural language processing (NLP) components. The main goal of this novel, hybrid integration paradigm is improving robustness of deep processing. After an introduction to constraint-based natural language parsing, we give an overview of typical shallow processing tasks. We introduce XML standoff markup as an additional abstraction layer that eases integration ...

  7. Sensory processing of deep tissue nociception in the rat spinal cord and thalamic ventrobasal complex.

    Science.gov (United States)

    Sikandar, Shafaq; West, Steven J; McMahon, Stephen B; Bennett, David L; Dickenson, Anthony H

    2017-07-01

    Sensory processing of deep somatic tissue constitutes an important component of the nociceptive system, yet associated central processing pathways remain poorly understood. Here, we provide a novel electrophysiological characterization and immunohistochemical analysis of neural activation in the lateral spinal nucleus (LSN). These neurons show evoked activity to deep, but not cutaneous, stimulation. The evoked responses of neurons in the LSN can be sensitized to somatosensory stimulation following intramuscular hypertonic saline, an acute model of muscle pain, suggesting this is an important spinal relay site for the processing of deep tissue nociceptive inputs. Neurons of the thalamic ventrobasal complex (VBC) mediate both cutaneous and deep tissue sensory processing, but in contrast to the lateral spinal nucleus our electrophysiological studies do not suggest the existence of a subgroup of cells that selectively process deep tissue inputs. The sensitization of polymodal and thermospecific VBC neurons to mechanical somatosensory stimulation following acute muscle stimulation with hypertonic saline suggests differential roles of thalamic subpopulations in mediating cutaneous and deep tissue nociception in pathological states. Overall, our studies at both the spinal (lateral spinal nucleus) and supraspinal (thalamic ventrobasal complex) levels suggest a convergence of cutaneous and deep somatosensory inputs onto spinothalamic pathways, which are unmasked by activation of muscle nociceptive afferents to produce consequent phenotypic alterations in spinal and thalamic neural coding of somatosensory stimulation. A better understanding of the sensory pathways involved in deep tissue nociception, as well as the degree of labeled line and convergent pathways for cutaneous and deep somatosensory inputs, is fundamental to developing targeted analgesic therapies for deep pain syndromes. © 2017 University College London. Physiological Reports published by Wiley Periodicals

  8. Animated construction of line drawings

    KAUST Repository

    Fu, Hongbo

    2011-12-01

    Revealing the sketching sequence of a line drawing can be visually intriguing and used for video-based storytelling. Typically this is enabled based on tedious recording of artists\\' drawing process. We demonstrate that it is often possible to estimate a reasonable drawing order from a static line drawing with clearly defined shape geometry, which looks plausible to a human viewer. We map the key principles of drawing order from drawing cognition to computational procedures in our framework. Our system produces plausible animated constructions of input line drawings, with no or little user intervention. We test our algorithm on a range of input sketches, with varying degree of complexity and structure, and evaluate the results via a user study. We also present applications to gesture drawing synthesis and drawing animation creation especially in the context of video scribing.

  9. Animated construction of line drawings

    KAUST Repository

    Fu, Hongbo

    2011-12-01

    Revealing the sketching sequence of a line drawing can be visually intriguing and used for video-based storytelling. Typically this is enabled based on tedious recording of artists\\' drawing process. We demonstrate that it is often possible to estimate a reasonable drawing order from a static line drawing with clearly defined shape geometry, which looks plausible to a human viewer. We map the key principles of drawing order from drawing cognition to computational procedures in our framework. Our system produces plausible animated constructions of input line drawings, with no or little user intervention. We test our algorithm on a range of input sketches, with varying degree of complexity and structure, and evaluate the results via a user study. We also present applications to gesture drawing synthesis and drawing animation creation especially in the context of video scribing. © 2011 ACM.

  10. SYNAPTIC DEPRESSION IN DEEP NEURAL NETWORKS FOR SPEECH PROCESSING.

    Science.gov (United States)

    Zhang, Wenhao; Li, Hanyu; Yang, Minda; Mesgarani, Nima

    2016-03-01

    A characteristic property of biological neurons is their ability to dynamically change the synaptic efficacy in response to variable input conditions. This mechanism, known as synaptic depression, significantly contributes to the formation of normalized representation of speech features. Synaptic depression also contributes to the robust performance of biological systems. In this paper, we describe how synaptic depression can be modeled and incorporated into deep neural network architectures to improve their generalization ability. We observed that when synaptic depression is added to the hidden layers of a neural network, it reduces the effect of changing background activity in the node activations. In addition, we show that when synaptic depression is included in a deep neural network trained for phoneme classification, the performance of the network improves under noisy conditions not included in the training phase. Our results suggest that more complete neuron models may further reduce the gap between the biological performance and artificial computing, resulting in networks that better generalize to novel signal conditions.

  11. Formation of metal and dielectric liners using a solution process for deep trench capacitors.

    Science.gov (United States)

    Ham, Yong-Hyun; Kim, Dong-Pyo; Baek, Kyu-Ha; Park, Kun-Sik; Kim, Moonkeun; Kwon, Kwang-Ho; Shin, Hong-Sik; Lee, Kijun; Do, Lee-Mi

    2012-07-01

    We demonstrated the feasibility of metal and dielectric liners using a solution process for deep trench capacitor application. The deep Si trench via with size of 10.3 microm and depth of 71 microm were fabricated by Bosch process in deep reactive ion etch (DRIE) system. The aspect ratio was about 7. Then, nano-Ag ink and poly(4-vinylphenol) (PVPh) were used to form metal and dielectric liners, respectively. The thicknesses of the Ag and PVPh liners were about 144 and 830 nm, respectively. When the curing temperature of Ag film increased from 120 to 150 degrees C, the sheet resistance decreased rapidly from 2.47 to 0.72 Omega/sq and then slightly decreased to 0.6 Omega/sq with further increasing the curing temperature beyond 150 degrees C. The proposed liner formation method using solution process is a simple and cost effective process for the high capacity of deep trench capacitor.

  12. A quark-parton description of the deep inelastic scattering processes

    International Nuclear Information System (INIS)

    Bajpai, R.P.

    1977-01-01

    A consistent description of various deep inelastic processes in a quark-parton model is presented. The valence quark probability distribution and the form of core quark probability distribution is fixed from the deep inelastic electroproduction data. Langacker and Suzuki prescription is used to fix the p and n quark core distribution. The differential excitation of quark currents similar to the Harari model of e + e - annihilation process is invoked in deep inelastic electroproduction and neutrino reactions. An effective phenomenological form of the weak currents associated with new quarks and the associated nucleon structure is determined. (author)

  13. Process optimization of a non-circular drawing sequence based on multi-surrogate assisted meta-heuristic algorithms

    Energy Technology Data Exchange (ETDEWEB)

    Pholdee, Nantiwat; Bureerat, Su Jin [Khon Kaen University, Khon Kaen (Thailand); Baek, Hyun Moo [DTaQ, Changwon (Korea, Republic of); Im, Yong Taek [KAIST, Daejeon (Korea, Republic of)

    2015-08-15

    Process optimization of a Non-circular drawing (NCD) sequence of a pearlitic steel wire was performed to improve the mechanical properties of a drawn wire based on surrogate assisted meta-heuristic algorithms. The objective function was introduced to minimize inhomogeneity of effective strain distribution at the cross-section of the drawn wire, which could deteriorate delamination characteristics of the drawn wires. The design variables introduced were die geometry and reduction of area of the NCD sequence. Several surrogate models and their combinations with the weighted sum technique were utilized. In the process optimization of the NCD sequence, the surrogate models were used to predict effective strain distributions at the cross-section of the drawn wire. Optimization using Differential evolution (DE) algorithm was performed, while the objective function was calculated from the predicted effective strains. The accuracy of all surrogate models was investigated, while optimum results were compared with the previous study available in the literature. It was found that hybrid surrogate models can improve prediction accuracy compared to a single surrogate model. The best result was obtained from the combination of Kriging (KG) and Support vector regression (SVR) models, while the second best was obtained from the combination of four surrogate models: Polynomial response surface (PRS), Radial basic function (RBF), KG, and SVR. The optimum results found in this study showed better effective strain homogeneity at the cross-section of the drawn wire with the same total reduction of area of the previous work available in the literature for fewer number of passes. The multi-surrogate models with the weighted sum technique were found to be powerful in improving the delamination characteristics of the drawn wire and reducing the production cost.

  14. Deep geothermal processes acting on faults and solid tides in coastal Xinzhou geothermal field, Guangdong, China

    Science.gov (United States)

    Lu, Guoping; Wang, Xiao; Li, Fusi; Xu, Fangyiming; Wang, Yanxin; Qi, Shihua; Yuen, David

    2017-03-01

    This paper investigated the deep fault thermal flow processes in the Xinzhou geothermal field in the Yangjiang region of Guangdong Province. Deep faults channel geothermal energy to the shallow ground, which makes it difficult to study due to the hidden nature. We conducted numerical experiments in order to investigate the physical states of the geothermal water inside the fault zone. We view the deep fault as a fast flow path for the thermal water from the deep crust driven up by the buoyancy. Temperature measurements at the springs or wells constrain the upper boundary, and the temperature inferred from the Currie temperature interface bounds the bottom. The deepened boundary allows the thermal reservoir to revolve rather than to be at a fixed temperature. The results detail the concept of a thermal reservoir in terms of its formation and heat distribution. The concept also reconciles the discrepancy in reservoir temperatures predicted from both quartz and Na-K-Mg. The downward displacement of the crust increases the pressure at the deep ground and leads to an elevated temperature and a lighter water density. Ultimately, our results are a first step in implementing numerical studies of deep faults through geothermal water flows; future works need to extend to cases of supercritical states. This approach is applicable to general deep-fault thermal flows and dissipation paths for the seismic energy from the deep crust.

  15. Nobel drawings

    CERN Multimedia

    Michel Blanc

    2009-01-01

    1. The Universe in One Drawing (G. Smoot Physics 2006) 2. Superfluid Properties (R. Richardson Physics 1996) 3. The Asymptotic Freedom of the Quark (David Gross, Physics 2004) 4. Understanding Superfluidity (Anthony Legget, Physics 2003) 5. Taming Infinities (G. 't Hooft, Physics 1999) 6. Homo Diagrammaticus (M. Veltman, Physics 1999) 7. A Tale Of Two Liquids (D. Osheroff, Physics 1996) 8. Wire Proliferation (G. Charpak, Physics 1992) 9. High Temperature Superconductivity (G. Bednorz, Physics 1987) 10. Atomic Cuisine (courtesy of C. Rubbia, Physics 1984) 11. Colliding Charm (S. Ting, Physics 1976) 12. The Bubble Chamber ( D. Glaser, Physics 1960) 13. The Narrow Resonance of the J-Psi (B. Richter, Physics 1976) 14. Stochastic Cooling (S. Van der Meer, Physics 1984) 15. The Good Anomaly (J Steinberger, Physics 1988) 16. Quark Somewhere on the White Paper (R. Taylor, Physics 1990) 17. The Tau of Particle Physics (M. Perl, 1995) 18. NMR Spectroscopy (K. Wuethrich, Chemistry 2002) 19. Coherent States (R....

  16. Hybrid robust deep and shallow semantic processing for creativity support in document production

    OpenAIRE

    Uszkoreit, Hans; Callmeier, Ulrich; Eisele, Andreas; Schäfer, Ulrich; Siegel, Melanie

    2004-01-01

    The research performed in the DeepThought project (http://www.project-deepthought.net) aims at demonstrating the potential of deep linguistic processing if added to existing shallow methods that ensure robustness. Classical information retrieval is extended by high precision concept indexing and relation detection. We use this approach to demonstrate the feasibility of three ambitious applications, one of which is a tool for creativity support in document production and collective brainstormi...

  17. Processes governing transient responses of the deep ocean buoyancy budget to a doubling of CO2

    Science.gov (United States)

    Palter, J. B.; Griffies, S. M.; Hunter Samuels, B. L.; Galbraith, E. D.; Gnanadesikan, A.

    2012-12-01

    Recent observational analyses suggest there is a temporal trend and high-frequency variability in deep ocean buoyancy in the last twenty years, a phenomenon reproduced even in low-mixing models. Here we use an earth system model (GFDL's ESM2M) to evaluate physical processes that influence buoyancy (and thus steric sea level) budget of the deep ocean in quasi-steady state and under a doubling of CO2. A new suite of model diagnostics allows us to quantitatively assess every process that influences the buoyancy budget and its temporal evolution, revealing surprising dynamics governing both the equilibrium budget and its transient response to climate change. The results suggest that the temporal evolution of the deep ocean contribution to sea level rise is due to a diversity of processes at high latitudes, whose net effect is then advected in the Eulerian mean flow to mid and low latitudes. In the Southern Ocean, a slowdown in convection and spin up of the residual mean advection are approximately equal players in the deep steric sea level rise. In the North Atlantic, the region of greatest deep steric sea level variability in our simulations, a decrease in mixing of cold, dense waters from the marginal seas and a reduction in open ocean convection causes an accumulation of buoyancy in the deep subpolar gyre, which is then advected equatorward.

  18. Array signal processing in the NASA Deep Space Network

    Science.gov (United States)

    Pham, Timothy T.; Jongeling, Andre P.

    2004-01-01

    In this paper, we will describe the benefits of arraying and past as well as expected future use of this application. The signal processing aspects of array system are described. Field measurements via actual tracking spacecraft are also presented.

  19. Drawing experts have better visual memory while drawing.

    Science.gov (United States)

    Perdreau, Florian; Cavanagh, Patrick

    2015-01-01

    Drawing involves frequent shifts of gaze between the original and the drawing and visual memory helps compare the original object and the drawing across these gaze shifts while creating and correcting the drawing. It remains unclear whether this memory encodes all of the object or only the features around the current drawing position and whether both the original and the copy are equally well represented. To address these questions, we designed a "drawing" experiment coupled with a change detection task. A polygon was displayed on one screen and participants had to copy it on another, with the original and the drawing presented in alternation. At unpredictable moments during the copying process, modifications were made on the drawing and the original figure (while they were not in view). Participants had to correct their drawing every time they perceived a change so that their drawing always matched the current original figure. Our results show a better memory representation of the original figure than of the drawing, with locations relevant to the current production most accurately represented. Critically, experts showed better memory for both the original and the drawing than did novices, suggesting that experts have specialized advantages for encoding visual shapes.

  20. Processing speed and working memory span: their differential role in superficial and deep memory processes in schizophrenia.

    Science.gov (United States)

    Brébion, Gildas; Bressan, Rodrigo A; Pilowsky, Lyn S; David, Anthony S

    2011-05-01

    Previous work has suggested that decrement in both processing speed and working memory span plays a role in the memory impairment observed in patients with schizophrenia. We undertook a study to examine simultaneously the effect of these two factors. A sample of 49 patients with schizophrenia and 43 healthy controls underwent a battery of verbal and visual memory tasks. Superficial and deep encoding memory measures were tallied. We conducted regression analyses on the various memory measures, using processing speed and working memory span as independent variables. In the patient group, processing speed was a significant predictor of superficial and deep memory measures in verbal and visual memory. Working memory span was an additional significant predictor of the deep memory measures only. Regression analyses involving all participants revealed that the effect of diagnosis on all the deep encoding memory measures was reduced to non-significance when processing speed was entered in the regression. Decreased processing speed is involved in verbal and visual memory deficit in patients, whether the task require superficial or deep encoding. Working memory is involved only insofar as the task requires a certain amount of effort.

  1. Software Graphics Processing Unit (sGPU) for Deep Space Applications

    Science.gov (United States)

    McCabe, Mary; Salazar, George; Steele, Glen

    2015-01-01

    A graphics processing capability will be required for deep space missions and must include a range of applications, from safety-critical vehicle health status to telemedicine for crew health. However, preliminary radiation testing of commercial graphics processing cards suggest they cannot operate in the deep space radiation environment. Investigation into an Software Graphics Processing Unit (sGPU)comprised of commercial-equivalent radiation hardened/tolerant single board computers, field programmable gate arrays, and safety-critical display software shows promising results. Preliminary performance of approximately 30 frames per second (FPS) has been achieved. Use of multi-core processors may provide a significant increase in performance.

  2. The Effects of Test Anxiety on Learning at Superficial and Deep Levels of Processing.

    Science.gov (United States)

    Weinstein, Claire E.; And Others

    1982-01-01

    Using a deep-level processing strategy, low test-anxious college students performed significantly better than high test-anxious students in learning a paired-associate word list. Using a superficial-level processing strategy resulted in no significant difference in performance. A cognitive-attentional theory and test anxiety mechanisms are…

  3. Deep processing activates the medial temporal lobe in young but not in old adults

    NARCIS (Netherlands)

    Daselaar, S.M.; Veltman, D.J.; Rombouts, S.A.R.B.; Raaijmakers, J.G.W.; Jonker, C.

    2003-01-01

    Age-related impairments in episodic memory have been related to a deficiency in semantic processing, based on the finding that elderly adults typically benefit less than young adults from deep, semantic as opposed to shallow, nonsemantic processing of study items. In the present study. we tested the

  4. Deep processing activates the medial temporal lobe in young but not in old adults.

    NARCIS (Netherlands)

    Daselaar, S.M.; Veltman, D.J.; Rombouts, S.A.R.B.; Raaijmakers, J.G.W.; Jonker, C.

    2003-01-01

    Age-related impairments in episodic memory have been related to a deficiency in semantic processing, based on the finding that elderly adults typically benefit less than young adults from deep, semantic as opposed to shallow, nonsemantic processing of study items. In the present study, we tested the

  5. Deep processing activates the medial temporal lobe in young but not in old adults

    NARCIS (Netherlands)

    Daselaar, Sander M.; Veltman, Dick J.; Rombouts, Serge A. R. B.; Raaijmakers, Jeroen G. W.; Jonker, Cees

    2003-01-01

    Age-related impairments in episodic memory have been related to a deficiency in semantic processing, based on the finding that elderly adults typically benefit less than young adults from deep, semantic as opposed to shallow, nonsemantic processing of study items. In the present study, we tested the

  6. Deep water overflow in the Faroe Bank Channel; modelling, processes, and impact

    DEFF Research Database (Denmark)

    Rullyanto, Arief

    , creating new water masses with distinct temperature, salinity and density characteristics. The change of water mass characteristics not only affects the local environment, but also far distant regions. The Faroe Bank Channel, which is located in the southern part of Faroe Islands, is one of the most...... under different circumstances. The focus is on the Faroe Bank Channel, a relatively small region, which has a significant impact on the global ocean circulation and marine organisms that live in its environment....... or tides, but also deep beneath the surface, where deep-water currents circulate waters throughout the world’s oceans. In certain very-localized regions, the flow of the deep-water has to travel over a sill in a narrow submarine channel. This overflow process mixes the deep water with overlying waters...

  7. Statistical Analysis of Deep Drilling Process Conditions Using Vibrations and Force Signals

    Directory of Open Access Journals (Sweden)

    Syafiq Hazwan

    2016-01-01

    Full Text Available Cooling systems is a key point for hot forming process of Ultra High Strength Steels (UHSS. Normally, cooling systems is made using deep drilling technique. Although deep twist drill is better than other drilling techniques in term of higher productivity however its main problem is premature tool breakage, which affects the production quality. In this paper, analysis of deep twist drill process parameters such as cutting speed, feed rate and depth of cut by using statistical analysis to identify the tool condition is presented. The comparisons between different two tool geometries are also studied. Measured data from vibrations and force sensors are being analyzed through several statistical parameters such as root mean square (RMS, mean, kurtosis, standard deviation and skewness. Result found that kurtosis and skewness value are the most appropriate parameters to represent the deep twist drill tool conditions behaviors from vibrations and forces data. The condition of the deep twist drill process been classified according to good, blunt and fracture. It also found that the different tool geometry parameters affect the performance of the tool drill. It believe the results of this study are useful in determining the suitable analysis method to be used for developing online tool condition monitoring system to identify the tertiary tool life stage and helps to avoid mature of tool fracture during drilling process.

  8. Optimum stamping die structure based on analytical method of die deformation during draw process; Seikei katei no kanagata henkei kaiseki ni motozuku, press kanagata kozo no saitekika

    Energy Technology Data Exchange (ETDEWEB)

    Nakahara, T; Tamai, H [Mazda Motor Corp., Hiroshima (Japan)

    1997-10-01

    We measured an actual deformation and pressure distribution in draw process of bending cam, and analyzed deformation process of die structure, in order to eliminate adjusting work considering die deformation by stamping force. We studied die structure improvement with simulation based on analytical method. This report describes a sample of die structure improvement based on a simulation and actual measurement. 1 ref., 11 figs., 1 tab.

  9. Headache in children's drawings.

    Science.gov (United States)

    Wojaczyńska-Stanek, Katarzyna; Koprowski, Robert; Wróbel, Zygmunt; Gola, Małgorzata

    2008-02-01

    Headache is a common health problem in childhood. Children's drawings are helpful in the diagnosis of headache type. Children, especially younger ones, communicate better through pictures than verbally. The aim of the present study is to evaluate the usefulness of drawings of the child's headache in the diagnostic process carried out by a pediatrician and a pediatric neurologist. At the beginning of a visit in a neurological clinic, or on the first day of hospitalization, the child was asked, "Please draw your headache," or "How do you feel your headache?" without any additional explanations or suggestions. Clinical diagnosis of headache type was made on the basis of the standard diagnostic evaluation. For the purpose of this study, children's headaches were categorized as migraine, tension-type headache, or "the others." One hundred twenty-four drawings of children with headaches were analyzed by 8 pediatricians and 8 pediatric neurologists. The analysts were unaware of the clinical history, age, sex, and diagnosis of the patients. The clinical diagnosis was considered the "gold standard" to which the headache drawing diagnosis was compared. There were 68 girls 5-18 years of age and 56 boys 7-18 years of age. Of the 124 children, 40 were clinically diagnosed with migraine (32.2%), 47 with tension-type headache (37.9%), and 37 (29.8%) as the others. Children with migraine most frequently draw sharp elements. Children with tension-type headache mainly drew compression elements and pressing elements. In the group of "the other" headaches, 21 children were diagnosed with somatoform disorders. The most frequent element in this group's drawings was a whirl in the head. Colors used most frequently were black and red, which signify severe pain. There was no difference in sensitivity of diagnoses between neurologists and pediatricians. Because the evaluation of drawings by children with headaches done both by pediatricians and pediatric neurologists was correct for

  10. Architectural Drawing - an Animate Field

    DEFF Research Database (Denmark)

    Hougaard, Anna Katrine

    2015-01-01

    Architectural drawing is changing because architects today draw with computers. Due to this change digital diagrams employed by computational architectural practices are often emphasized as powerful structures of control and organisation in the design process. But there are also diagrams, which do...... ways of directing behaviour of artefacts and living things without controlling this behaviour completely. I analyse a musical composition by John Cage as an example of a sketch diagram, and then hypothesize that orthogonal, architectural drawing can work in similar ways. Thereby I hope to point out...... important affordance of architectural drawing as a ¬hybrid between the openness of hand-sketching and the rule-based-ness of diagramming, an affordance which might be useful in the migrational zone of current architectural drawing where traditional hand drawing techniques and computer drawing techniques...

  11. PARAMETRIC DRAWINGS VS. AUTOLISP

    Directory of Open Access Journals (Sweden)

    PRUNĂ Liviu

    2015-06-01

    Full Text Available In this paper the authors make a critical analysis of the advantages offered by the parametric drawing use by comparison with the AutoLISP computer programs used when it comes about the parametric design. Studying and analysing these two work models the authors have got to some ideas and conclusions which should be considered in the moment in that someone must to decide if it is the case to elaborate a software, using the AutoLISP language, or to establish the base rules that must be followed by the drawing, in the idea to construct outlines or blocks which can be used in the projection process.

  12. Uniform, optimal signal processing of mapped deep-sequencing data.

    Science.gov (United States)

    Kumar, Vibhor; Muratani, Masafumi; Rayan, Nirmala Arul; Kraus, Petra; Lufkin, Thomas; Ng, Huck Hui; Prabhakar, Shyam

    2013-07-01

    Despite their apparent diversity, many problems in the analysis of high-throughput sequencing data are merely special cases of two general problems, signal detection and signal estimation. Here we adapt formally optimal solutions from signal processing theory to analyze signals of DNA sequence reads mapped to a genome. We describe DFilter, a detection algorithm that identifies regulatory features in ChIP-seq, DNase-seq and FAIRE-seq data more accurately than assay-specific algorithms. We also describe EFilter, an estimation algorithm that accurately predicts mRNA levels from as few as 1-2 histone profiles (R ∼0.9). Notably, the presence of regulatory motifs in promoters correlates more with histone modifications than with mRNA levels, suggesting that histone profiles are more predictive of cis-regulatory mechanisms. We show by applying DFilter and EFilter to embryonic forebrain ChIP-seq data that regulatory protein identification and functional annotation are feasible despite tissue heterogeneity. The mathematical formalism underlying our tools facilitates integrative analysis of data from virtually any sequencing-based functional profile.

  13. Deep Magnetic Diagenesis in Sediments: Progressive and Punctuated Processes.

    Science.gov (United States)

    Musgrave, R. J.; Kars, M. A. C.; Vega, M. E.

    2017-12-01

    Magnetic diagenesis in the tuffaceous muds, mudstones and volcaniclastic rocks cored at IODP Site U1437 is a product of progressive processes that continue throughout the 1800-m-thick sequence, punctuated by superimposed features corresponding to a series of influxes of fluids and concentrations of hydrocarbons. XRD, visual examination and SEM images indicate the presence of both magnetite and the magnetic sulfide greigite. Inferences from high values of saturation isothermal remanence normalised by magnetic susceptibility (SIRM/χ), distribution of hysteresis data near a diagenetic greigite curve on a Day plot, and 'humping' of low-temperature cycles of SIRM suggest that detrital magnetite and diagenetic greigite are both significant contributors to the magnetic assemblage, with greigite constituting a higher proportion in shallower samples. Progressive magnetic diagenesis is expressed as a continuing background decrease in SIRM/χ. FORC curves indicate an initial diagenetic growth of one or more higher-coercivity phases, followed downhole by increasing loss of all but low-coercivity material. The downhole pattern is consistent with progressive loss of fine-grained magnetite, initial authigenesis of greigite, and progressive pyritisation of the greigite. Some coarse-grained samples from the base of the sequence buck the trend, exhibiting SD behavior probably related to surviving magnetite inclusions in silicates. Shipboard fluid analysis revealed a complex profile of interstitial-water geochemistry, marked by several fluid influxes, including inputs of sulfate-rich water at about 275 and 460 meters below seafloor (mbsf). Methane concentrations, mostly low, markedly increase in the interval between 750 and 1460 mbsf, and ethane appears below an inferred fault at 1104 mbsf. Each of these fluid events is marked by offsets in the rock magnetic parameters SIRM/χ, S-0.3T, and DJH, representing repeated phases of late diagenetic growth of greigite in response to

  14. Microstructure, Texture Evolution and Mechanical Properties of VT3-1 Titanium Alloy Processed by Multi-Pass Drawing and Subsequent Isothermal Annealing

    Directory of Open Access Journals (Sweden)

    Xiaofei Lei

    2017-04-01

    Full Text Available Microstructure, texture evolution, and mechanical properties of Ti–6Al–1.5Cr–2.5Mo–0.5Fe–0.3Si (VT3-1 titanium alloy processed by multi-pass drawing and subsequent isothermal annealing were systematically investigated. A fiber-like microstructure is formed after warm drawing at 760 °C with 60% area reduction. After isothermal annealing, the samples deformed to different amounts of area reduction show a similar volume fraction (80% of α phase, while the sample deformed to 60% exhibits a homogeneous microstructure with a larger grain size (5.8 μm. The major texture component of α phase developed during warm drawing is centered at a position of {φ1 = 10°, φ = 65°, φ2 = 0°}. The textures for annealed samples are almost along the orientation of original deformation textures and show significant increases in orientation density and volume fraction compared with their deformed states. In addition, for the drawn samples, the ultimate tensile strength increases but the ductility decreases with increasing drawing deformation. A negative slope of yield strength of annealed samples versus grain size (d−1/2 is found due to the difference between texture softening for as-rolled + annealed state and texture hardening for drawn + annealed state. The mechanical properties of annealed samples are found to be strongly dependent on grain size and texture, resulting in the balance of the strength and ductility.

  15. Attenuation of deep semantic processing during mind wandering: an event-related potential study.

    Science.gov (United States)

    Xu, Judy; Friedman, David; Metcalfe, Janet

    2018-03-21

    Although much research shows that early sensory and attentional processing is affected by mind wandering, the effect of mind wandering on deep (i.e. semantic) processing is relatively unexplored. To investigate this relation, we recorded event-related potentials as participants studied English-Spanish word pairs, one at a time, while being intermittently probed for whether they were 'on task' or 'mind wandering'. Both perceptual processing, indexed by the P2 component, and deep processing, indexed by a late, sustained slow wave maximal at parietal electrodes, was attenuated during periods preceding participants' mind wandering reports. The pattern when participants were on task, rather than mind wandering, is similar to the subsequent memory or difference in memory effect. These results support previous findings of sensory attenuation during mind wandering, and extend them to a long-duration slow wave by suggesting that the deeper and more sustained levels of processing are also disrupted.

  16. Process optimization of a deep trench isolation structure for high voltage SOI devices

    International Nuclear Information System (INIS)

    Zhu Kuiying; Qian Qinsong; Zhu Jing; Sun Weifeng

    2010-01-01

    The process reasons for weak point formation of the deep trench on SOI wafers have been analyzed in detail. An optimized trench process is also proposed. It is found that there are two main reasons: one is over-etching laterally of the silicon on the surface of the buried oxide caused by a fringe effect; and the other is the slow growth rate of the isolation oxide in the concave silicon corner of the trench bottom. In order to improve the isolation performance of the deep trench, two feasible ways for optimizing the trench process are proposed. The improved process thickens the isolation oxide and rounds sharp silicon corners at their weak points, increasing the applied voltage by 15-20 V at the same leakage current. The proposed new trench isolation process has been verified in the foundry's 0.5-μm HV SOI technology. (semiconductor devices)

  17. Descending projections from the dysgranular zone of rat primary somatosensory cortex processing deep somatic input.

    Science.gov (United States)

    Lee, Taehee; Kim, Uhnoh

    2012-04-01

    In the mammalian somatic system, peripheral inputs from cutaneous and deep receptors ascend via different subcortical channels and terminate in largely separate regions of the primary somatosensory cortex (SI). How these inputs are processed in SI and then projected back to the subcortical relay centers is critical for understanding how SI may regulate somatic information processing in the subcortex. Although it is now relatively well understood how SI cutaneous areas project to the subcortical structures, little is known about the descending projections from SI areas processing deep somatic input. We examined this issue by using the rodent somatic system as a model. In rat SI, deep somatic input is processed mainly in the dysgranular zone (DSZ) enclosed by the cutaneous barrel subfields. By using biotinylated dextran amine (BDA) as anterograde tracer, we characterized the topography of corticostriatal and corticofugal projections arising in the DSZ. The DSZ projections terminate mainly in the lateral subregions of the striatum that are also known as the target of certain SI cutaneous areas. This suggests that SI processing of deep and cutaneous information may be integrated, to a certain degree, in this striatal region. By contrast, at both thalamic and prethalamic levels as far as the spinal cord, descending projections from DSZ terminate in areas largely distinguishable from those that receive input from SI cutaneous areas. These subcortical targets of DSZ include not only the sensory but also motor-related structures, suggesting that SI processing of deep input may engage in regulating somatic and motor information flow between the cortex and periphery. Copyright © 2011 Wiley-Liss, Inc.

  18. The stratigraphic record and processes of turbidity current transformation across deep-marine lobes

    NARCIS (Netherlands)

    Kane, Ian A.; Ponten, Anna; Vangdal, Brita; Eggenhuisen, Joris|info:eu-repo/dai/nl/322850274; Hodgson, David M.; Spychala, Yvonne T.|info:eu-repo/dai/nl/411435019

    Sedimentary facies in the distal parts of deep-marine lobes can diverge significantly from those predicted by classical turbidite models, and sedimentological processes in these environments are poorly understood. This gap may be bridged using outcrop studies and theoretical models. In the

  19. Relations between Goals, Self-Efficacy, Critical Thinking and Deep Processing Strategies: A Path Analysis

    Science.gov (United States)

    Phan, Huy Phuong

    2009-01-01

    Research exploring students' academic learning has recently amalgamated different motivational theories within one conceptual framework. The inclusion of achievement goals, self-efficacy, deep processing and critical thinking has been cited in a number of studies. This article discusses two empirical studies that examined these four theoretical…

  20. On connection between coefficient functions for deep inelastic and annihilation processes

    International Nuclear Information System (INIS)

    Gabadadze, G.T.; Kataev, A.L.

    1995-01-01

    It has been shown that the one-loop behaviour of the axial anomaly, occurring when the axial current is appropriately normalized, leads to the cancellation of the corrections of type C F N-N α s , (N≥1) in the Crewther relation for the coefficient functions of deep inelastic and annihilation processes. 11 refs

  1. Effects of charged Higgs bosons in the deep inelastic process ντ N ...

    Indian Academy of Sciences (India)

    the value of the contribution of the W± exchange diagrams, provided MH± .... section rates of the charged current deep inelastic process ντ N in the frame of the ..... rates do not depend on the choice of the cuts on the momentum transfer square.

  2. A simple model for the quark fragmentation functions seen in deep inelastic processes

    International Nuclear Information System (INIS)

    Seiden, A.

    1977-01-01

    Using some simple assumptions, a calculation is presented of the quark fragmentation functions seen in deep inelastic processes. The results provide evidence for the conjecture that both jets seen in high p(perpendicular) reactions at the ISR stem from similar parents. The calculated functions are in excellent agreement with the inclusive distributions seen in γp and anti γp scattering, and in particular explain the puzzling presence of leading π - 's from the fragmentation of a leading up quark. The results are also in agreement with the charge ratios extracted from deep inelastic electron scattering. (Auth.)

  3. Partonic transverse motion in unpolarized semi-inclusive deep inelastic scattering processes

    International Nuclear Information System (INIS)

    Boglione, M.; Melis, S.; Prokudin, A.

    2011-01-01

    We analyze the role of partonic transverse motion in unpolarized semi-inclusive deep inelastic scattering processes. Imposing appropriate kinematical conditions, we find some constraints which fix an upper limit to the range of allowed k perpendicular values. We show that, applying these additional requirements on the partonic kinematics, we obtain different results with respect to the usual phenomenological approach based on the Gaussian smearing with analytical integration over an unlimited range of k perpendicular values. These variations are particularly interesting for some observables, like the h > azimuthal modulation of the unpolarized semi-inclusive deep inelastic scattering cross section or the average transverse momentum of the final, detected hadron.

  4. Deep Space 1 arrives at KSC and processing begins in the PHSF

    Science.gov (United States)

    1998-01-01

    NASA's Deep Space 1 spacecraft waits in the Payload Hazardous Servicing Facility for prelaunch processing. Targeted for launch on a Boeing Delta 7326 rocket on Oct. 15, 1998, the first flight in NASA's New Millennium Program is designed to validate 12 new technologies for scientific space missions of the next century. Onboard experiments include an ion propulsion engine and software that tracks celestial bodies so the spacecraft can make its own navigation decisions without the intervention of ground controllers. Deep Space 1 will complete most of its mission objectives within the first two months, but will also do a flyby of a near-Earth asteroid, 1992 KD, in July 1999.

  5. Effect of Heat Drawing Process on Mechanical Properties of Dry-Jet Wet Spun Fiber of Linear Low Density Polyethylene/Carbon Nanotube Composites

    Directory of Open Access Journals (Sweden)

    Jong Won Kim

    2017-01-01

    Full Text Available Polyethylene is one of the most commonly used polymer materials. Even though linear low density polyethylene (LLDPE has better mechanical properties than other kinds of polyethylene, it is not used as a textile material because of its plastic behavior that is easy to break at the die during melt spinning. In this study, LLDPE fibers were successfully produced with a new approach using a dry-jet wet spinning and a heat drawing process. The fibers were filled with carbon nanotubes (CNTs to improve the strength and reduce plastic deformation. The crystallinity, degree of orientation, mechanical properties (strength to yield, strength to break, elongation at break, and initial modulus, electrical conductivity, and thermal properties of LLDPE fibers were studied. The results show that the addition of CNTs improved the tensile strength and the degree of crystallinity. The heat drawing process resulted in a significant increase in the tensile strength and the orientation of the CNTs and polymer chains. In addition, this study demonstrates that the heat drawing process effectively decreases the plastic deformation of LLDPE.

  6. Deep processing activates the medial temporal lobe in young but not in old adults.

    Science.gov (United States)

    Daselaar, Sander M; Veltman, Dick J; Rombouts, Serge A R B; Raaijmakers, Jeroen G W; Jonker, Cees

    2003-11-01

    Age-related impairments in episodic memory have been related to a deficiency in semantic processing, based on the finding that elderly adults typically benefit less than young adults from deep, semantic as opposed to shallow, nonsemantic processing of study items. In the present study, we tested the hypothesis that elderly adults are not able to perform certain cognitive operations under deep processing conditions. We further hypothesised that this inability does not involve regions commonly associated with lexical/semantic retrieval processes, but rather involves a dysfunction of the medial temporal lobe (MTL) memory system. To this end, we used functional MRI on rather extensive groups of young and elderly adults to compare brain activity patterns obtained during a deep (living/nonliving) and a shallow (uppercase/lowercase) classification task. Common activity in relation to semantic classification was observed in regions that have been previously related to semantic retrieval, including mainly left-lateralised activity in the inferior prefrontal, middle temporal, and middle frontal/anterior cingulate gyrus. Although the young adults showed more activity in some of these areas, the finding of mainly overlapping activation patterns during semantic classification supports the idea that lexical/semantic retrieval processes are still intact in elderly adults. This received further support by the finding that both groups showed similar behavioural performances as well on the deep and shallow classification tasks. Importantly, though, the young revealed significantly more activity than the elderly adults in the left anterior hippocampus during deep relative to shallow classification. This finding is in line with the idea that age-related impairments in episodic encoding are, at least partly, due to an under-recruitment of the medial temporal lobe memory system.

  7. Young Children's Drawings in Problem Solving

    Science.gov (United States)

    Bakar, Kamariah Abu; Way, Jennifer; Bobis, Janette

    2016-01-01

    This paper explores young children's drawings (6 years old) in early number and addition activities in Malaysia. Observation, informal interviews and analysis of drawings revealed two types of drawing, and gave insight into the transitional process required for children to utilise drawings in problem solving. We argue the importance of valuing and…

  8. Process strategies for ultra-deep x-ray lithography at the Advanced Photon Source

    International Nuclear Information System (INIS)

    Mancini, D.C.; Moldovan, N.; Divan, R.; De Carlo, F.; Yaeger, J.

    2001-01-01

    For the past five years, we have been investigating and advancing processing capabilities for deep x-ray lithography (DXRL) using synchrotron radiation from a bending magnet at the Advanced Photon Source (APS), with an emphasis on ultra-deep structures (1mm to 1cm thick). The use of higher-energy x-rays has presented many challenges in developing optimal lithographic techniques for high-aspect ratio structures: mask requirements, resist preparation, exposure, development, and post-processing. Many problems are more severe for high-energy exposure of thicker films than for sub-millimeter structures and affect resolution, processing time, adhesion, damage, and residue. A number of strategies have been created to overcome the challenges and limitations of ultra-deep x-ray lithography (UDXRL), that have resulted in the current choices for mask, substrate, and process flow at the APS. We describe our current process strategies for UDXRL, how they address the challenges presented, and their current limitations. We note especially the importance of the process parameters for use of the positive tone resist PMMA for UDXRL, and compare to the use of negative tone resists such as SU-8 regarding throughput, resolution, adhesion, damage, and post-processing.

  9. Characterization of a deep radiological contamination: integration of geostatistical processing and historical data - 59062

    International Nuclear Information System (INIS)

    Desnoyers, Yvon; De Moura, Patrick

    2012-01-01

    The problem of site characterization is quite complex, especially for deep radiological contamination. This article illustrates the added value of the geo-statistical processing on a real application case dealing with grounds of facilities partially dismantled at the end of the 1950's in Fontenay-aux-Roses CEA Center (France). 12 years ago, a first exploratory drill-hole confirmed the presence of a deep radiological contamination (more than 4 m deep). More recently, 8 additional drill-holes failed to delineate the contamination extension. The integration of the former topography and other geological data led to the realization of 10 additional drill holes. This final stage significantly improved the characterization of the radiological contamination, which impacted the remediation project and the initially estimated volumes. (authors)

  10. Architectural Drawing - an Animate Field

    DEFF Research Database (Denmark)

    Hougaard, Anna Katrine

    2015-01-01

    Architectural drawing is changing because architects today draw with computers. Due to this change digital diagrams employed by computational architectural practices are often emphasized as powerful structures of control and organisation in the design process. But there are also diagrams, which d...

  11. Vacuum arc behavior and its voltage characteristics in drawing process controlled by composite magnetic fields along axial and transverse directions

    International Nuclear Information System (INIS)

    Wang, Lijun; Deng, Jie; Wang, Haijing; Jia, Shenli; Qin, Kang; Shi, Zongqian

    2015-01-01

    In this research, drawing vacuum arc (VA) experiments were conducted using composite contacts under currents ranging from 5 kA to 20 kA root mean square (rms). The new type of contact comprised an axial magnetic field (AMF) configuration and a transverse magnetic field (TMF) configuration. The TMF plate was in the center, surrounded by the AMF plate. The contact generated both AMFs and TMFs simultaneously. VA appearances and arc voltages were recorded, and the VA was modeled as a conductor for electromagnetic force analysis in ANSYS software. The results showed that the coaxiality of operating mechanisms significantly influenced arc behavior just as the arc was ignited. When arc brightness did not increase after ignition, there was a voltage drop accompanied with diffusion of the VA. As to VA development, when an arc was ignited on an AMF plate, it spread on the plate and rotated. Over time the arc current increased, the constricting arc forms, and the arc column rotated on the TMF plate under the action of Ampere's force. With regard to the influence of a magnetic field on a VA at different stages, in the initial drawing arc stage the TMF was dominant, and the arc started to rotate under the action of Ampere's force. Afterwards, the AMF was dominant, with a steadily burning arc. As for contact melting, in the initial arcing period, a contracted short arc caused severe melting and erosion of the contact plate. When the ignition spot or root was close to the slot of plate, the electromagnetic force pushed the arc toward slot and contact edge, resulting in local erosion of the slot region

  12. Drawing evaluation report for sampling equipment drawings

    International Nuclear Information System (INIS)

    WILSON, G.W.

    1999-01-01

    This document presents the results of a task to evaluate Tank Waste Remediation System (TWRS) sampling equipment drawings and identifies drawings category as either essential, support, or general drawings. This report completes the drawing evaluation task as outlined in Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation (Wilson, 1997). The scope of this report is limited to an evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the TRWS Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, and all core sampling equipment (see LMHC Task Order 304). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Light Duty Utility Arm (LDUA), Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The LDUA drawings are addressed in the Characterization Equipment Essential Drawings (HNF 1998). The Cone Penetrometer system drawings which are vendor drawings (not H- series) is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and were not included in the original scope for this evaluation and will be addressed in the evaluation update scheduled for fiscal year 1999

  13. Deep brain stimulation of the subthalamic nucleus enhances emotional processing in Parkinson disease.

    Science.gov (United States)

    Schneider, Frank; Habel, Ute; Volkmann, Jens; Regel, Sabine; Kornischka, Jürgen; Sturm, Volker; Freund, Hans-Joachim

    2003-03-01

    High-frequency electrical stimulation of the subthalamic nucleus is a new and highly effective therapy for complications of long-term levodopa therapy and motor symptoms in advanced Parkinson disease (PD). Clinical observations indicate additional influence on emotional behavior. Electrical stimulation of deep brain nuclei with pulse rates above 100 Hz provokes a reversible, lesioning-like effect. Here, the effect of deep brain stimulation of the subthalamic nucleus on emotional, cognitive, and motor performance in patients with PD (n = 12) was examined. The results were compared with the effects of a suprathreshold dose of levodopa intended to transiently restore striatal dopamine deficiency. Patients were tested during medication off/stimulation off (STIM OFF), medication off/stimulation on (STIM ON), and during the best motor state after taking levodopa without deep brain stimulation (MED). More positive self-reported mood and an enhanced mood induction effect as well as improvement in emotional memory during STIM ON were observed, while during STIM OFF, patients revealed reduced emotional performance. Comparable effects were revealed by STIM ON and MED. Cognitive performance was not affected by the different conditions and treatments. Deep brain stimulation of the subthalamic nucleus selectively enhanced affective processing and subjective well-being and seemed to be antidepressive. Levodopa and deep brain stimulation had similar effects on emotion. This finding may provide new clues about the neurobiologic bases of emotion and mood disorders, and it illustrates the important role of the basal ganglia and the dopaminergic system in emotional processing in addition to the well-known motor and cognitive functions.

  14. Constrained Convolutional Sparse Coding for Parametric Based Reconstruction of Line Drawings

    KAUST Repository

    Shaheen, Sara

    2017-12-25

    Convolutional sparse coding (CSC) plays an essential role in many computer vision applications ranging from image compression to deep learning. In this work, we spot the light on a new application where CSC can effectively serve, namely line drawing analysis. The process of drawing a line drawing can be approximated as the sparse spatial localization of a number of typical basic strokes, which in turn can be cast as a non-standard CSC model that considers the line drawing formation process from parametric curves. These curves are learned to optimize the fit between the model and a specific set of line drawings. Parametric representation of sketches is vital in enabling automatic sketch analysis, synthesis and manipulation. A couple of sketch manipulation examples are demonstrated in this work. Consequently, our novel method is expected to provide a reliable and automatic method for parametric sketch description. Through experiments, we empirically validate the convergence of our method to a feasible solution.

  15. Implementation of an Antenna Array Signal Processing Breadboard for the Deep Space Network

    Science.gov (United States)

    Navarro, Robert

    2006-01-01

    The Deep Space Network Large Array will replace/augment 34 and 70 meter antenna assets. The array will mainly be used to support NASA's deep space telemetry, radio science, and navigation requirements. The array project will deploy three complexes in the western U.S., Australia, and European longitude each with 400 12m downlink antennas and a DSN central facility at JPL. THis facility will remotely conduct all real-time monitor and control for the network. Signal processing objectives include: provide a means to evaluate the performance of the Breadboard Array's antenna subsystem; design and build prototype hardware; demonstrate and evaluate proposed signal processing techniques; and gain experience with various technologies that may be used in the Large Array. Results are summarized..

  16. Study on the process of calibration and deep centring of blanks

    International Nuclear Information System (INIS)

    Potapov, I.N.; Romantsev, B.A.; Popov, V.A.; Volodin, V.V.; Goncharuk, A.V.

    1985-01-01

    Process of calibration and deep centring of blanks before broaching is developed and studied. Investigations are performed at a semi-industrial screw rolling mill MISiS-100 T. Blanks made of 40Kh, 60, 50, 45KhN2MFA, 30KhGSNA steels 80, 85, and 90 mm in diameter and 300 mm long were calibrated and centered after heating in a furnace to a depth of 200 mm at shafts and faces with different calibration. 30KhN2MFA steel is chosen for face material; heat treatment is conducted under the following conditions: heating up to 950-1000 deg C and hold-up during 30-35 min with the following cooling in the air. The above experimental investigations reveal that the process of calibration and deep centring accomplished at a three-shaft screw rolling mill is rather stable and provides a high accuracy of centering hollow marking

  17. Concrete decontamination: two innovative processes in response to surface or deep contamination

    International Nuclear Information System (INIS)

    CUER, F.; Nadai, A. de; Faure, S.

    2008-01-01

    To meet the future needs in the nuclear industry as regards dismantling and decommissioning, the LPAD (Laboratoire des Procedes Avances de Decontamination) develops new specific techniques to decontaminate concretes: the drying gel process adapted to surface contamination and the electrokinetics process to treat deep contamination. Indeed, because the concrete constitute a porous medium, two types of contamination can be met according to the environment to which is subjected the material. In the case of an accidental or dry contamination, radio elements do not penetrate beyond the first millimeters of the material. The contamination is then considered as surface. On the contrary, the contamination is considered as 'deep' when radioactive ions have diffused deeply under the effects of the natural diffusion. This is the case in fuel storage pond or other many nuclear infrastructures. (authors)

  18. K-factors in the deep inelastic Compton and Drell-Yan processes

    International Nuclear Information System (INIS)

    Czechowski, A.; Krawczyk, M.

    1983-01-01

    The associated production of hadrons is used to answer the question about the nature of large QCD corrections for hard processes. The results of the order α s calculation of K-factors for the deep inelastic Compton process and some predictions for the large p perpendicular to Drell-Yan pair production in hadron-hadron collision are presented. In the soft gluon approximation a significant difference between K-factors corresponding to different inclusive distributions in each of these processes is found. (author)

  19. A Psychometric Study of Reading Processes in L2 Acquisition: Deploying Deep Processing to Push Learners' Discourse Towards Syntactic Processing-Based Constructions

    Science.gov (United States)

    Manuel, Carlos J.

    2009-01-01

    This study assesses reading processes and/or strategies needed to deploy deep processing that could push learners towards syntactic-based constructions in L2 classrooms. Research has found L2 acquisition to present varying degrees of success and/or fossilization (Bley-Vroman 1989, Birdsong 1992 and Sharwood Smith 1994). For example, learners have…

  20. The drawing effect: Evidence for reliable and robust memory benefits in free recall.

    Science.gov (United States)

    Wammes, Jeffrey D; Meade, Melissa E; Fernandes, Myra A

    2016-01-01

    In 7 free-recall experiments, the benefit of creating drawings of to-be-remembered information relative to writing was examined as a mnemonic strategy. In Experiments 1 and 2, participants were presented with a list of words and were asked to either draw or write out each. Drawn words were better recalled than written. Experiments 3-5 showed that the memory boost provided by drawing could not be explained by elaborative encoding (deep level of processing, LoP), visual imagery, or picture superiority, respectively. In Experiment 6, we explored potential limitations of the drawing effect, by reducing encoding time and increasing list length. Drawing, relative to writing, still benefited memory despite these constraints. In Experiment 7, the drawing effect was significant even when encoding trial types were compared in pure lists between participants, inconsistent with a distinctiveness account. Together these experiments indicate that drawing enhances memory relative to writing, across settings, instructions, and alternate encoding strategies, both within- and between-participants, and that a deep LoP, visual imagery, or picture superiority, alone or collectively, are not sufficient to explain the observed effect. We propose that drawing improves memory by encouraging a seamless integration of semantic, visual, and motor aspects of a memory trace.

  1. Sedimentary Markers : a window into deep geodynamic processes Examples from the Western Mediterranean Sea

    Science.gov (United States)

    Rabineau, Marina; Aslanian, Daniel; Leroux, Estelle; Pellen, Romain; Gorini, Christian; Moulin, Maryline; Droz, Laurence; Bache, Francois; Molliex, Stephane; Silenzario, Carmine; Rubino, Jean-Loup

    2017-04-01

    Deep Earth dynamics impact so strongly on surface geological processes that we can use sediment palaeo-markers as a window into the deeper Earth. Derived from climatic and tectonic erosive actions on the continents, and related to eustasy, subsidence and isostasy, the sediment in a deep basin is the main recorder of these processes. Nevertheless, defining and quantifying the relative roles of parameters that interact to give the final sedimentary architecture is not a simple task. Using a 3D-grid of seismic and wide-angle data, boreholes and numerical stratigraphic modelling, we propose here a quantification of post-rift vertical movements in the Provençal Basin (Western Mediterranean) involving three domains of subsidence: seaward tilting on the platform and the slope and purely vertical subsidence in the deep basin (Rabineau et al., 2014 ; Leroux et al., 2015). These domains fit the deeper crustal domains highlighted by previous geophysical data (Moulin et al., 2015 ; Afilhado et al., 2015). Post-break-up sedimentary markers may therefore be used to identify the initial hinge lines of the rifting phase, to quantify sedimentation rates and isostatic rebound (Rabineau et al., 2014) and redefine the subsidence laws. Similar work and results are obtained in the Valencia Basin (Pellen et al., 2016). This Western Mediterranean Sea is a natural laboratory with very high total subsidence rates that enable high sedimentation rates along the margin with sediments provided by the Rhône and Ebro rivers flowing from the Alps, the Pyrennees and Catalan chains, which in turn archives the detailed record of climate/tectonic evolution during the Neogene. The Western Mediterranean Sea could therefore further probe deep-earth and surface connections using deep drillings of this land-locked ocean basin transformed into a giant saline basin (Rabineau et al., 2015). Leroux, E., Aslanian, D., Rabineau, M., M. Moulin, D. Granjeon, C. Gorini, L. Droz, 2015. Sedimentary markers: a

  2. The role of deep-water sedimentary processes in shaping a continental margin: The Northwest Atlantic

    Science.gov (United States)

    Mosher, David C.; Campbell, D.C.; Gardner, J.V.; Piper, D.J.W.; Chaytor, Jason; Rebesco, M.

    2017-01-01

    The tectonic history of a margin dictates its general shape; however, its geomorphology is generally transformed by deep-sea sedimentary processes. The objective of this study is to show the influences of turbidity currents, contour currents and sediment mass failures on the geomorphology of the deep-water northwestern Atlantic margin (NWAM) between Blake Ridge and Hudson Trough, spanning about 32° of latitude and the shelf edge to the abyssal plain. This assessment is based on new multibeam echosounder data, global bathymetric models and sub-surface geophysical information.The deep-water NWAM is divided into four broad geomorphologic classifications based on their bathymetric shape: graded, above-grade, stepped and out-of-grade. These shapes were created as a function of the balance between sediment accumulation and removal that in turn were related to sedimentary processes and slope-accommodation. This descriptive method of classifying continental margins, while being non-interpretative, is more informative than the conventional continental shelf, slope and rise classification, and better facilitates interpretation concerning dominant sedimentary processes.Areas of the margin dominated by turbidity currents and slope by-pass developed graded slopes. If sediments did not by-pass the slope due to accommodation then an above grade or stepped slope resulted. Geostrophic currents created sedimentary bodies of a variety of forms and positions along the NWAM. Detached drifts form linear, above-grade slopes along their crests from the shelf edge to the deep basin. Plastered drifts formed stepped slope profiles. Sediment mass failure has had a variety of consequences on the margin morphology; large mass-failures created out-of-grade profiles, whereas smaller mass failures tended to remain on the slope and formed above-grade profiles at trough-mouth fans, or nearly graded profiles, such as offshore Cape Fear.

  3. Important processes affecting the release and migration of radionuclides from a deep geological repository

    International Nuclear Information System (INIS)

    Barátová, Dana; Nečas, Vladimír

    2017-01-01

    The processes that affect significantly the transport of contaminants through the near field and far field of a deep geological repository of spent nuclear fuel were studied. The processes can be generally divided into (i) processes related to the release of radionuclides from the spent nuclear fuel; (ii) processes related to the radionuclide transport mechanisms (such as advection and diffusion); and (iii) processes affecting the rate of radionuclide migration through the multi-barrier repository system. A near-field and geosphere model of an unspecified geological repository sited in a crystalline rock is also described. Focus of the treatment is on the effects of the different processes on the activity flow of the major safety-relevant radionuclides. The activity flow was simulated for one spent fuel cask by using the GoldSim simulation tool. (orig.)

  4. Structure and properties of melt-spun high acrylonitrile copolymer fibers via continuous zone-drawing and zone-annealing processes

    International Nuclear Information System (INIS)

    Wu Zongquan; Zhang Anqiu; Percec, Simona; Jin Shi; Jing, Alexander J.; Ge, Jason J.; Cheng, Stephen Z.D.

    2003-01-01

    Continuous zone-drawing and zone-annealing processes have been utilized to probe improvements in mechanical performance of melt-spun high acrylonitrile copolymer fibers (AMLON TM ). The as-spun fibers were zone-drawn at different ratios in a narrow temperature range of 100-105 deg. C and then zone-annealed. As a result of these processes, the fibers show substantial increases in tensile strength and tensile modulus (about three times) and significant improvements in elongation-at-break (about two times) after zone annealing. The thermal transition behavior, dimensional stability and dynamic relaxation properties of the as-spun, zone-drawn and zone-annealed fibers have been studied using differential scanning calorimetry, thermal mechanical and dynamic mechanical experiments. Their mechanical and thermal property changes after the zone-drawing and zone-annealing processes can be associated with the microscopic structural evolution including crystallinity, crystal orientation and apparent crystallite size detected by wide angle X-ray diffraction experiments

  5. Flexible and fast: linguistic shortcut affects both shallow and deep conceptual processing.

    Science.gov (United States)

    Connell, Louise; Lynott, Dermot

    2013-06-01

    Previous research has shown that people use linguistic distributional information during conceptual processing, and that it is especially useful for shallow tasks and rapid responding. Using two conceptual combination tasks, we showed that this linguistic shortcut extends to the processing of novel stimuli, is used in both successful and unsuccessful conceptual processing, and is evident in both shallow and deep conceptual tasks. Specifically, as predicted by the ECCo theory of conceptual combination, people use the linguistic shortcut as a "quick-and-dirty" guide to whether the concepts are likely to combine into a coherent conceptual representation, in both shallow sensibility judgment and deep interpretation generation tasks. Linguistic distributional frequency predicts both the likelihood and the time course of rejecting a novel word compound as nonsensical or uninterpretable. However, it predicts the time course of successful processing only in shallow sensibility judgment, because the deeper conceptual process of interpretation generation does not allow the linguistic shortcut to suffice. Furthermore, the effects of linguistic distributional frequency are independent of any effects of conventional word frequency. We discuss the utility of the linguistic shortcut as a cognitive triage mechanism that can optimize processing in a limited-resource conceptual system.

  6. Encoding-related brain activity during deep processing of verbal materials: a PET study.

    Science.gov (United States)

    Fujii, Toshikatsu; Okuda, Jiro; Tsukiura, Takashi; Ohtake, Hiroya; Suzuki, Maki; Kawashima, Ryuta; Itoh, Masatoshi; Fukuda, Hiroshi; Yamadori, Atsushi

    2002-12-01

    The recent advent of neuroimaging techniques provides an opportunity to examine brain regions related to a specific memory process such as episodic memory encoding. There is, however, a possibility that areas active during an assumed episodic memory encoding task, compared with a control task, involve not only areas directly relevant to episodic memory encoding processes but also areas associated with other cognitive processes for on-line information. We used positron emission tomography (PET) to differentiate these two kinds of regions. Normal volunteers were engaged in deep (semantic) or shallow (phonological) processing of new or repeated words during PET. Results showed that deep processing, compared with shallow processing, resulted in significantly better recognition performance and that this effect was associated with activation of various brain areas. Further analyses revealed that there were regions directly relevant to episodic memory encoding in the anterior part of the parahippocampal gyrus, inferior frontal gyrus, supramarginal gyrus, anterior cingulate gyrus, and medial frontal lobe in the left hemisphere. Our results demonstrated that several regions, including the medial temporal lobe, play a role in episodic memory encoding.

  7. Analysis of the processes defining radionuclide migration from deep geological repositories in porous medium

    International Nuclear Information System (INIS)

    Brazauskaite, A.; Poskas, P.

    2004-01-01

    Due to the danger of exposure arising from long-lived radionuclides to humans and environment, spent nuclear fuel (SNF) and high level waste (HLW) are not allowed to be disposed of in near surface repositories. There exists an international consensus that such high level and long-lived radioactive wastes are best disposed of in geological repositories using a system of engineered and natural barriers. At present, the geological repository of SNF and HLW has not been realized yet in any country but there is a lot of experience in the assessment of radionuclide migration from deep repositories, investigations of different processes related to the safety of a disposal system. The aim of this study was to analyze the processes related to the radionuclide migration from deep geological repositories in porous medium such as SNF matrix dissolution, release mechanism of radionuclides from SNF matrix, radionuclide solubility, sorption, diffusive, advective transport of radionuclides from the canister and through the engineered and natural barriers. It has been indicated that SNF matrix dissolution, radionuclide solubility and sorption are sensitive to ambient conditions prevailing in the repository. The approaches that could be used for modeling the radionuclide migration from deep repositories in porous medium are also presented. (author)

  8. Drawing Evaluation Report for Sampling Equipment Drawings

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    This document presents the results of a task to update the evaluation of River Protection Project (WP) sampling equipment drawings and updates the assigned drawings category as either essential, support, or general drawings. This report updates the drawing evaluation that was originally done per Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation. The scope of this report is limited to updating the evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the RPP Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, all core sampling equipment, and Light Duty Utility Arm (LDUA) (see LMHC contract No. 519, release 10). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The Cone Penetrometer system, which is depicted on vendor drawings, (not H- series), is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and was not included in the original scope for this update and will be addressed in the evaluation update scheduled for later in fiscal year 1999, when equipment ownership is determined

  9. Drawing cure: children's drawings as a psychoanalytic instrument.

    Science.gov (United States)

    Wittmann, Barbara

    2010-01-01

    This essay deals with the special case of drawings as psychoanalytical instruments. It aims at a theoretical understanding of the specific contribution made by children's drawings as a medium of the psychical. In the influential play technique developed by Melanie Klein, drawing continuously interacts with other symptomatic (play) actions. Nonetheless, specific functions of drawing within the play technique can be identified. The essay will discuss four crucial aspects in-depth: 1) the strengthening of the analysis's recursivity associated with the graphic artifact; 2) the opening of the analytic process facilitated by drawing; 3) the creation of a genuinely graphic mode of producing meaning that allows the child to develop a "theory" of the workings of his own psychic apparatus; and 4) the new possibilities of symbolization associated with the latter. In contrast to classical definitions of the psychological instrument, the child's drawing is a weakly structured tool that does not serve to reproduce psychic processes in an artificial, controlled setting. The introduction of drawing into the psychoanalytic cure is by no means interested in replaying past events, but in producing events suited to effecting a transformation of the synchronic structures of the unconscious.

  10. Uniform lateral etching of tungsten in deep trenches utilizing reaction-limited NF3 plasma process

    Science.gov (United States)

    Kofuji, Naoyuki; Mori, Masahito; Nishida, Toshiaki

    2017-06-01

    The reaction-limited etching of tungsten (W) with NF3 plasma was performed in an attempt to achieve the uniform lateral etching of W in a deep trench, a capability required by manufacturing processes for three-dimensional NAND flash memory. Reaction-limited etching was found to be possible at high pressures without ion irradiation. An almost constant etching rate that showed no dependence on NF3 pressure was obtained. The effect of varying the wafer temperature was also examined. A higher wafer temperature reduced the threshold pressure for reaction-limited etching and also increased the etching rate in the reaction-limited region. Therefore, the control of the wafer temperature is crucial to controlling the etching amount by this method. We found that the uniform lateral etching of W was possible even in a deep trench where the F radical concentration was low.

  11. Lift-off process for deep-submicron-size junctions using supercritical CO2

    International Nuclear Information System (INIS)

    Fukushima, A.; Kubota, H.; Yuasa, S.; Takahachi, T.; Kadoriku, S.; Miyake, K.

    2007-01-01

    Deep-submicron-size (∼100-nm-size) junctions are a key element to investigate spin-torque transfer phenomena such as current induced magnetization reversal or the spin-torque diode effect. In the fabrication of submicron-size junctions using an etching method, the lift-off process after the etching process tends to be difficult as the size of junctions shrinks. In this study, we present a new lift-off process using supercritical CO 2 . In this process, the samples were immersed in solvent (mixture of N-Methyl-2-pyrrolidone and isopropanol), and pressurized by CO 2 gas. The CO 2 gas then went into supercritical phase and the solvent was removed by a continuous flow of CO 2 . We obtained considerable yield rate (success ratio in lift-off process) of more than 50% for the samples down to 100-nm-size junctions

  12. From transport and storage to control of the process: the challenge of biodigestion from drawings of swine in agroindustrial scale

    Directory of Open Access Journals (Sweden)

    José Carlos Souza Oliveira

    2017-07-01

    The objective of this article is to analyze some factors that represent challenges to the application of biodigestion process for energy generation from swine waste on an agroindustrial scale, thus contributing to important reflection on the design and installation of biodigesters in agroindustrial activities.

  13. Canada's Deep Geological Repository for Used Nuclear Fuel - Geo-scientific Site Evaluation Process - 13117

    International Nuclear Information System (INIS)

    Blyth, Alec; Ben Belfadhel, Mahrez; Hirschorn, Sarah; Hamilton, Duncan; McKelvie, Jennifer

    2013-01-01

    The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable rock formation at a depth of approximately 500 meters (m) (1,640 feet [ft]). In May 2010, the NWMO published a nine-step site selection process that serves as the road map to decision-making on the location for the deep geological repository. The safety and appropriateness of any potential site will be assessed against a number of factors, both technical and social in nature. The selected site will be one that can be demonstrated to be able to safely contain and isolate used nuclear fuel, protecting humans and the environment over the very long term. The geo-scientific suitability of potential candidate sites will be assessed in a stepwise manner following a progressive and thorough site evaluation process that addresses a series of geo-scientific factors revolving around five safety functions. The geo-scientific site evaluation process includes: Initial Screenings; Preliminary Assessments; and Detailed Site Evaluations. As of November 2012, 22 communities have entered the site selection process (three in northern Saskatchewan and 18 in northwestern and southwestern Ontario). (authors)

  14. Stochastic process variation in deep-submicron CMOS circuits and algorithms

    CERN Document Server

    Zjajo, Amir

    2014-01-01

    One of the most notable features of nanometer scale CMOS technology is the increasing magnitude of variability of the key device parameters affecting performance of integrated circuits. The growth of variability can be attributed to multiple factors, including the difficulty of manufacturing control, the emergence of new systematic variation-generating mechanisms, and most importantly, the increase in atomic-scale randomness, where device operation must be described as a stochastic process. In addition to wide-sense stationary stochastic device variability and temperature variation, existence of non-stationary stochastic electrical noise associated with fundamental processes in integrated-circuit devices represents an elementary limit on the performance of electronic circuits. In an attempt to address these issues, Stochastic Process Variation in Deep-Submicron CMOS: Circuits and Algorithms offers unique combination of mathematical treatment of random process variation, electrical noise and temperature and ne...

  15. Emotional words can be embodied or disembodied: the role of superficial vs. deep types of processing

    Directory of Open Access Journals (Sweden)

    Ensie eAbbassi

    2015-07-01

    Full Text Available Emotional words are processed rapidly and automatically in the left hemisphere (LH and slowly, with the involvement of attention, in the right hemisphere (RH. This review aims to find the reason for this difference and suggests that emotional words can be processed superficially or deeply due to the involvement of the linguistic and imagery systems, respectively. During superficial processing, emotional words likely make connections only with semantically associated words in the LH. This part of the process is automatic and may be sufficient for the purpose of language processing. Deep processing, in contrast, seems to involve conceptual information and imagery of a word’s perceptual and emotional properties using autobiographical memory contents. Imagery and the involvement of autobiographical memory likely differentiate between emotional and neutral word processing and explain the salient role of the RH in emotional word processing. It is concluded that the level of emotional word processing in the RH should be deeper than in the LH and, thus, it is conceivable that the slow mode of processing adds certain qualities to the output.

  16. Emotional words can be embodied or disembodied: the role of superficial vs. deep types of processing.

    Science.gov (United States)

    Abbassi, Ensie; Blanchette, Isabelle; Ansaldo, Ana I; Ghassemzadeh, Habib; Joanette, Yves

    2015-01-01

    Emotional words are processed rapidly and automatically in the left hemisphere (LH) and slowly, with the involvement of attention, in the right hemisphere (RH). This review aims to find the reason for this difference and suggests that emotional words can be processed superficially or deeply due to the involvement of the linguistic and imagery systems, respectively. During superficial processing, emotional words likely make connections only with semantically associated words in the LH. This part of the process is automatic and may be sufficient for the purpose of language processing. Deep processing, in contrast, seems to involve conceptual information and imagery of a word's perceptual and emotional properties using autobiographical memory contents. Imagery and the involvement of autobiographical memory likely differentiate between emotional and neutral word processing and explain the salient role of the RH in emotional word processing. It is concluded that the level of emotional word processing in the RH should be deeper than in the LH and, thus, it is conceivable that the slow mode of processing adds certain qualities to the output.

  17. Emotional words can be embodied or disembodied: the role of superficial vs. deep types of processing

    Science.gov (United States)

    Abbassi, Ensie; Blanchette, Isabelle; Ansaldo, Ana I.; Ghassemzadeh, Habib; Joanette, Yves

    2015-01-01

    Emotional words are processed rapidly and automatically in the left hemisphere (LH) and slowly, with the involvement of attention, in the right hemisphere (RH). This review aims to find the reason for this difference and suggests that emotional words can be processed superficially or deeply due to the involvement of the linguistic and imagery systems, respectively. During superficial processing, emotional words likely make connections only with semantically associated words in the LH. This part of the process is automatic and may be sufficient for the purpose of language processing. Deep processing, in contrast, seems to involve conceptual information and imagery of a word’s perceptual and emotional properties using autobiographical memory contents. Imagery and the involvement of autobiographical memory likely differentiate between emotional and neutral word processing and explain the salient role of the RH in emotional word processing. It is concluded that the level of emotional word processing in the RH should be deeper than in the LH and, thus, it is conceivable that the slow mode of processing adds certain qualities to the output. PMID:26217288

  18. Canada's deep geological repository for used nuclear fuel - site selection process update

    International Nuclear Information System (INIS)

    Facella, J.

    2014-01-01

    In 2007, the Government of Canada selected Adaptive Phased Management as Canada's plan for the long-term management of Canada's used nuclear fuel in a deep geological repository, located in an informed and willing host. The process of site selection is an important milestone in this program. The NWMO describes its approach to working collaboratively with communities which expressed interest in exploring the project, as well as Aboriginal communities in the area and other surrounding communities. The project is designed to be implemented through a long-term partnership involving the interested community, Aboriginal communities and surrounding communities working with the NWMO. (author)

  19. Expanding Music Listening Experience through Drawing

    Science.gov (United States)

    Han, Yo-Jung

    2016-01-01

    Drawing while listening to music provides an opportunity for students to imagine and associate, leading to holistic listening experience. The personal qualitative listening experience triggered by music can be revealed in their drawings. In the process of representing of the listening experience through drawing, students can also increase their…

  20. An adaptive deep-coupled GNSS/INS navigation system with hybrid pre-filter processing

    Science.gov (United States)

    Wu, Mouyan; Ding, Jicheng; Zhao, Lin; Kang, Yingyao; Luo, Zhibin

    2018-02-01

    The deep-coupling of a global navigation satellite system (GNSS) with an inertial navigation system (INS) can provide accurate and reliable navigation information. There are several kinds of deeply-coupled structures. These can be divided mainly into coherent and non-coherent pre-filter based structures, which have their own strong advantages and disadvantages, especially in accuracy and robustness. In this paper, the existing pre-filters of the deeply-coupled structures are analyzed and modified to improve them firstly. Then, an adaptive GNSS/INS deeply-coupled algorithm with hybrid pre-filters processing is proposed to combine the advantages of coherent and non-coherent structures. An adaptive hysteresis controller is designed to implement the hybrid pre-filters processing strategy. The simulation and vehicle test results show that the adaptive deeply-coupled algorithm with hybrid pre-filters processing can effectively improve navigation accuracy and robustness, especially in a GNSS-challenged environment.

  1. [The importance of drawing in adolescence].

    Science.gov (United States)

    Titia Rizzi, Alice

    Teenagers like to draw. A drawing is a fundamental object of creativity in the process of re-construction and change typical of this period. However, theoretical approaches often consider that the evolution of the stages of drawing come to an end in adolescence. It is important to consider the practical and clinical benefit of drawing and to develop expression-based activities which can be carried out with this population. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  2. Deep Incremental Boosting

    OpenAIRE

    Mosca, Alan; Magoulas, George D

    2017-01-01

    This paper introduces Deep Incremental Boosting, a new technique derived from AdaBoost, specifically adapted to work with Deep Learning methods, that reduces the required training time and improves generalisation. We draw inspiration from Transfer of Learning approaches to reduce the start-up time to training each incremental Ensemble member. We show a set of experiments that outlines some preliminary results on some common Deep Learning datasets and discuss the potential improvements Deep In...

  3. Geometric and engineering drawing

    CERN Document Server

    Morling, K

    2010-01-01

    The new edition of this successful text describes all the geometric instructions and engineering drawing information that are likely to be needed by anyone preparing or interpreting drawings or designs with plenty of exercises to practice these principles.

  4. Analysis of the deep rolling process on turbine blades using the FEM/BEM-coupling

    International Nuclear Information System (INIS)

    Baecker, V; Klocke, F; Wegner, H; Timmer, A; Grzhibovskis, R; Rjasanow, S

    2010-01-01

    Highly stressed components of aircraft engines, like turbine blades, have to satisfy stringent requirements regarding durability and reliability. The induction of compressive stresses and strain hardening in their surface layer has proven as a promising method to significantly increase their fatigue resistance. The required surface layer properties can be achieved by deep rolling. The determination of optimal process parameters still requires elaborate experimental set-up and subsequent time- and cost-extensive measurements. In previous works the application of the Finite Element Method (FEM) was proposed as an effective and cost reducing alternative to predict the surface layer state for given process parameters. However, FEM requires very fine mesh in the surface layer to resolve the high stress gradients with sufficient accuracy. The hereby caused high time and memory requirements render an efficient simulation of complete turbine components as impossible. In this article a solution is offered by coupling the FEM with the Boundary Elements Method (BEM). It enables the computing of large scale models at low computational cost and high result accuracy. Different approaches of the FEM/BEM-coupling for the simulation of deep rolling are examined with regard to their stability and required computing time.

  5. Deep-inelastic multinucleon transfer processes in the 16O+27Al reaction

    Science.gov (United States)

    Roy, B. J.; Sawant, Y.; Patwari, P.; Santra, S.; Pal, A.; Kundu, A.; Chattopadhyay, D.; Jha, V.; Pandit, S. K.; Parkar, V. V.; Ramachandran, K.; Mahata, K.; Nayak, B. K.; Saxena, A.; Kailas, S.; Nag, T. N.; Sahoo, R. N.; Singh, P. P.; Sekizawa, K.

    2018-03-01

    The reaction mechanism of deep-inelastic multinucleon transfer processes in the 16O+27Al reaction at an incident 16O energy (Elab=134 MeV) substantially above the Coulomb barrier has been studied both experimentally and theoretically. Elastic-scattering angular distribution, total kinetic energy loss spectra, and angular distributions for various transfer channels have been measured. The Q -value- and angle-integrated isotope production cross sections have been deduced. To obtain deeper insight into the underlying reaction mechanism, we have carried out a detailed analysis based on the time-dependent Hartree-Fock (TDHF) theory. A recently developed method, TDHF+GEMINI, has been applied to evaluate production cross sections for secondary products. From a comparison between the experimental and theoretical cross sections, we find that the theory qualitatively reproduces the experimental data. Significant effects of secondary light-particle emissions are demonstrated. Possible interplay among fusion-fission, deep-inelastic, multinucleon transfer, and particle evaporation processes is discussed.

  6. Automatic tissue image segmentation based on image processing and deep learning

    Science.gov (United States)

    Kong, Zhenglun; Luo, Junyi; Xu, Shengpu; Li, Ting

    2018-02-01

    Image segmentation plays an important role in multimodality imaging, especially in fusion structural images offered by CT, MRI with functional images collected by optical technologies or other novel imaging technologies. Plus, image segmentation also provides detailed structure description for quantitative visualization of treating light distribution in the human body when incorporated with 3D light transport simulation method. Here we used image enhancement, operators, and morphometry methods to extract the accurate contours of different tissues such as skull, cerebrospinal fluid (CSF), grey matter (GM) and white matter (WM) on 5 fMRI head image datasets. Then we utilized convolutional neural network to realize automatic segmentation of images in a deep learning way. We also introduced parallel computing. Such approaches greatly reduced the processing time compared to manual and semi-automatic segmentation and is of great importance in improving speed and accuracy as more and more samples being learned. Our results can be used as a criteria when diagnosing diseases such as cerebral atrophy, which is caused by pathological changes in gray matter or white matter. We demonstrated the great potential of such image processing and deep leaning combined automatic tissue image segmentation in personalized medicine, especially in monitoring, and treatments.

  7. Higher-twist effects in QCD, deep inelastic scattering, and the Drell-Yan process

    International Nuclear Information System (INIS)

    Berger, E.L.; Stanford Univ., CA

    1980-01-01

    Inclusion of specific effects associated with constituent binding in hadronic wave functions is shown to lead to important non-scaling, non-factorizing 1/Q 2 contributions to cross sections for semi-inclusive deep-inelastic scattering, the Drell-Yan process, and other hard scattering reactions. These 1/Q 2 higher-twist terms are predicted to be dominant in well defined kinematic regions such as large x and/or large z. The provide angular distributions typical of longitudinally polarized virtual photons and W's, including sin 2 theta terms in meson induced Drell-Yan processes and in e + e - → πX, as well as unusual (1-γ) terms in deep-inelastic scattering. Calculations are also presented of the quark structure functions of the pion qsub(π)(x,Q 2 ) and for the quark to pion fragmentation function Dsub(π)(z,Q 2 ). Predictions are made for the azimuthal angle dependence of the cross sections for πN → μ anti μX and IN → l'πX. (orig.)

  8. Uncovering molecular relaxation processes with nonlinear spectroscopies in the deep UV

    International Nuclear Information System (INIS)

    West, Brantley A.; Molesky, Brian P.; Giokas, Paul G.; Moran, Andrew M.

    2013-01-01

    Highlights: • We discuss the outlook for multidimensional spectroscopies in the deep UV. • Photophysics are examined in small DNA components at cryogenic temperatures. • Wavepacket motions are detected in ring-opening systems with 2DUV spectroscopy. • Measurements of electronic wavepacket motions in molecules are proposed. - Abstract: Nonlinear laser spectroscopies in the deep UV spectral range are motivated by studies of biological systems and elementary processes in small molecules. This perspective article discusses recent technical advances in this area with a particular emphasis on diffractive optic based approaches to four-wave mixing spectroscopies. Applications to two classes of systems illustrate present experimental capabilities. First, experiments on DNA components at cryogenic temperatures are used to uncover features of excited state potential energy surfaces and vibrational cooling mechanisms. Second, sub-200 fs internal conversion processes and coherent wavepacket motions are investigated in cyclohexadiene and α-terpinene. Finally, we propose new experimental directions that combine methods for producing few-cycle UV laser pulses in noble gases with incoherent detection methods (e.g., photoionization) in experiments with time resolution near a singlefemtosecond. These measurements are motivated by knowledge of extremely fast non-adiabatic dynamics and the resolution of electronic wavepacket motions in molecules

  9. Post-processing of Deep Web Information Extraction Based on Domain Ontology

    Directory of Open Access Journals (Sweden)

    PENG, T.

    2013-11-01

    Full Text Available Many methods are utilized to extract and process query results in deep Web, which rely on the different structures of Web pages and various designing modes of databases. However, some semantic meanings and relations are ignored. So, in this paper, we present an approach for post-processing deep Web query results based on domain ontology which can utilize the semantic meanings and relations. A block identification model (BIM based on node similarity is defined to extract data blocks that are relevant to specific domain after reducing noisy nodes. Feature vector of domain books is obtained by result set extraction model (RSEM based on vector space model (VSM. RSEM, in combination with BIM, builds the domain ontology on books which can not only remove the limit of Web page structures when extracting data information, but also make use of semantic meanings of domain ontology. After extracting basic information of Web pages, a ranking algorithm is adopted to offer an ordered list of data records to users. Experimental results show that BIM and RSEM extract data blocks and build domain ontology accurately. In addition, relevant data records and basic information are extracted and ranked. The performances precision and recall show that our proposed method is feasible and efficient.

  10. Deep recurrent neural network reveals a hierarchy of process memory during dynamic natural vision.

    Science.gov (United States)

    Shi, Junxing; Wen, Haiguang; Zhang, Yizhen; Han, Kuan; Liu, Zhongming

    2018-05-01

    The human visual cortex extracts both spatial and temporal visual features to support perception and guide behavior. Deep convolutional neural networks (CNNs) provide a computational framework to model cortical representation and organization for spatial visual processing, but unable to explain how the brain processes temporal information. To overcome this limitation, we extended a CNN by adding recurrent connections to different layers of the CNN to allow spatial representations to be remembered and accumulated over time. The extended model, or the recurrent neural network (RNN), embodied a hierarchical and distributed model of process memory as an integral part of visual processing. Unlike the CNN, the RNN learned spatiotemporal features from videos to enable action recognition. The RNN better predicted cortical responses to natural movie stimuli than the CNN, at all visual areas, especially those along the dorsal stream. As a fully observable model of visual processing, the RNN also revealed a cortical hierarchy of temporal receptive window, dynamics of process memory, and spatiotemporal representations. These results support the hypothesis of process memory, and demonstrate the potential of using the RNN for in-depth computational understanding of dynamic natural vision. © 2018 Wiley Periodicals, Inc.

  11. Optimization of WEDM process parameters using deep cryo-treated Inconel 718 as work material

    Directory of Open Access Journals (Sweden)

    Bijaya Bijeta Nayak

    2016-03-01

    Full Text Available The present work proposes an experimental investigation and optimization of various process parameters during taper cutting of deep cryo-treated Inconel 718 in wire electrical discharge machining process. Taguchi's design of experiment is used to gather information regarding the process with less number of experimental runs considering six input parameters such as part thickness, taper angle, pulse duration, discharge current, wire speed and wire tension. Since traditional Taguchi method fails to optimize multiple performance characteristics, maximum deviation theory is applied to convert multiple performance characteristics into an equivalent single performance characteristic. Due to the complexity and non-linearity involved in this process, good functional relationship with reasonable accuracy between performance characteristics and process parameters is difficult to obtain. To address this issue, the present study proposes artificial neural network (ANN model to determine the relationship between input parameters and performance characteristics. Finally, the process model is optimized to obtain a best parametric combination by a new meta-heuristic approach known as bat algorithm. The results of the proposed algorithm show that the proposed method is an effective tool for simultaneous optimization of performance characteristics during taper cutting in WEDM process.

  12. Deep Sequence Analysis of AgoshRNA Processing Reveals 3' A Addition and Trimming.

    Science.gov (United States)

    Harwig, Alex; Herrera-Carrillo, Elena; Jongejan, Aldo; van Kampen, Antonius Hubertus; Berkhout, Ben

    2015-07-14

    The RNA interference (RNAi) pathway, in which microprocessor and Dicer collaborate to process microRNAs (miRNA), was recently expanded by the description of alternative processing routes. In one of these noncanonical pathways, Dicer action is replaced by the Argonaute2 (Ago2) slicer function. It was recently shown that the stem-length of precursor-miRNA or short hairpin RNA (shRNA) molecules is a major determinant for Dicer versus Ago2 processing. Here we present the results of a deep sequence study on the processing of shRNAs with different stem length and a top G·U wobble base pair (bp). This analysis revealed some unexpected properties of these so-called AgoshRNA molecules that are processed by Ago2 instead of Dicer. First, we confirmed the gradual shift from Dicer to Ago2 processing upon shortening of the hairpin length. Second, hairpins with a stem larger than 19 base pair are inefficiently cleaved by Ago2 and we noticed a shift in the cleavage site. Third, the introduction of a top G·U bp in a regular shRNA can promote Ago2-cleavage, which coincides with a loss of Ago2-loading of the Dicer-cleaved 3' strand. Fourth, the Ago2-processed AgoshRNAs acquire a short 3' tail of 1-3 A-nucleotides (nt) and we present evidence that this product is subsequently trimmed by the poly(A)-specific ribonuclease (PARN).

  13. HippoDraw

    International Nuclear Information System (INIS)

    Gravina, M.F.; Kunz, P.F.; Rensing, P.E.

    1992-09-01

    HippoDraw is a NeXTSTEP application for viewing statistical data. It has several unique features which make viewing data distributions highly interactive. It also incorporates a set of simple drawing tools. HippoDraw is written in Objective-C and uses the Hippoplotamus library package to handle the n-tuples and displays

  14. Universitality features in (pp), (e+e-), and deep inelastic scattering process

    International Nuclear Information System (INIS)

    Zichichi, A.

    1985-01-01

    This paper discusses the use of the correct variables in (pp), (e + e - ), and deep-inelastic scattering (DIS) processes which allow universality features to be established different ways of producing mulihadronic states. The experimental data where (pp) interactions are compared with (e + e - ) are shown. Extrapolations of collider physics are discussed and it is found that the leading effects must be subtracted and the correct variables have to be used if one wants to compare purely hadronic interactions with (e + e - ) and DIS. The new method of studying (pp) and (pp) collisions allows one to put on equal footing the multiparticle systems that are produced in purely hadronic interactions, in (e + e - ) annihilation, and in DIS processes

  15. Canada's deep geological repository for used nuclear fuel - the geoscientific site evaluation process

    Energy Technology Data Exchange (ETDEWEB)

    Belfadhel, M.B.; Blyth, A.; Desroches, A.; Hirschorn, S.; Mckelvie, J.; Sanchez-Rico Castejon, M.; Parmenter, A.; Urrutia-Bustos, A.; Vorauer, A., E-mail: mbenbelfadhel@nwmo.ca [Nuclear Waste Management Organization, Toronto, ON (Canada)

    2014-07-01

    The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for the long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable crystalline or sedimentary rock formation. In May 2010, the NWMO initiated a nine-step site selection process to find an informed and willing community to host the project. This paper describes the approach, methods and criteria being used to assess the geoscientific suitability of communities currently involved in the site selection process. The social, cultural and economic aspects of the assessment are discussed in a companion paper. (author)

  16. Quark initial state interaction in deep inelastic scattering and the Drell-Yan process

    International Nuclear Information System (INIS)

    Linnyk, O.; Leupold, S.; Mosel, U.

    2005-01-01

    We pursue a phenomenological study of higher-twist effects in high-energy processes by taking into account the off-shellness (virtuality) of partons bound in the nucleon. The effect of parton off-shellness in deep inelastic ep→eX scattering (DIS) and the Drell-Yan process (pp→llX) is examined. Assuming factorization and a single-parameter Breit-Wigner form for the parton spectral function, we develop a model to calculate the corresponding off-shell cross sections. Allowing for a finite parton width ≅100 MeV, we reproduce the data of both DIS and the triple-differential Drell-Yan cross section without an additional K-factor. The results are compared to those from perturbative QCD and the intrinsic-k T approach

  17. Effects of deep cryogenic treatment on the solid-state phase transformation of Cu-Al alloy in cooling process

    Science.gov (United States)

    Wang, Yuhui; Liao, Bo; Liu, Jianhua; Chen, Shuqing; Feng, Yu; Zhang, Yanyan; Zhang, Ruijun

    2012-07-01

    The solid-state phase transformation temperature and duration of deep cryogenic treated and untreated Cu-Al alloys in cooling process were measured by differential scanning calorimetry measurement. The solid-state phase transformation activation energy and Avrami exponent were calculated according to these measurements. The effects of deep cryogenic treatment on the solid-state phase transformation were investigated based on the measurement and calculation as well as the observation of alloy's microstructure. The results show that deep cryogenic treatment can increase the solid-phase transformation activation energy and shorten the phase transformation duration, which is helpful to the formation of fine grains in Cu-Al alloy.

  18. Effective As(III) Removal by A Multi-Charged Hydroacid Complex Draw Solute Facilitated Forward Osmosis-Membrane Distillation (FO-MD) Processes

    KAUST Repository

    Ge, Qingchun; Han, Gang; Chung, Neal Tai-Shung

    2016-01-01

    © 2016 American Chemical Society. Effective removal of As(III) from water by an oxalic acid complex with the formula of Na3[Cr(C2O4)3] (Na-Cr-OA) is demonstrated via an forward osmosis-membrane distillation (FO-MD) hybrid system in this study. Na-Cr-OA first proved its superiority as a draw solute with high water fluxes and negligible reverse fluxes in FO, then a systematic investigation of the Na-Cr-OA promoted FO process was conducted to ascertain the factors in As(III) removal. Relatively high water fluxes of 28 LMH under the FO mode and 74 LMH under the pressure retarded osmosis (PRO) mode were achieved when using a 1000 ppm As(III) solution as the feed and 1.0 M Na-Cr-OA as the draw solution at 60 °C. As(III) removal with a water recovery up to 21.6% (FO mode) and 48.3% (PRO mode) were also achieved in 2 h. An outstanding As(III) rejection with 30-3000 μg/L As(III) in the permeate was accomplished when As(III) feed solutions varied from 5 × 104 to 1 × 106 μg/L, superior to the best FO performance reported for As(III) removal. Incorporating MD into FO not only makes As(III) removal sustainable by reconcentrating the Na-Cr-OA solution simultaneously, but also reduces the As(III) concentration below 10 μg/L in the product water, meeting the WHO standard.

  19. Effective As(III) Removal by A Multi-Charged Hydroacid Complex Draw Solute Facilitated Forward Osmosis-Membrane Distillation (FO-MD) Processes.

    Science.gov (United States)

    Ge, Qingchun; Han, Gang; Chung, Tai-Shung

    2016-03-01

    Effective removal of As(III) from water by an oxalic acid complex with the formula of Na3[Cr(C2O4)3] (Na-Cr-OA) is demonstrated via an forward osmosis-membrane distillation (FO-MD) hybrid system in this study. Na-Cr-OA first proved its superiority as a draw solute with high water fluxes and negligible reverse fluxes in FO, then a systematic investigation of the Na-Cr-OA promoted FO process was conducted to ascertain the factors in As(III) removal. Relatively high water fluxes of 28 LMH under the FO mode and 74 LMH under the pressure retarded osmosis (PRO) mode were achieved when using a 1000 ppm As(III) solution as the feed and 1.0 M Na-Cr-OA as the draw solution at 60 °C. As(III) removal with a water recovery up to 21.6% (FO mode) and 48.3% (PRO mode) were also achieved in 2 h. An outstanding As(III) rejection with 30-3000 μg/L As(III) in the permeate was accomplished when As(III) feed solutions varied from 5 × 10(4) to 1 × 10(6) μg/L, superior to the best FO performance reported for As(III) removal. Incorporating MD into FO not only makes As(III) removal sustainable by reconcentrating the Na-Cr-OA solution simultaneously, but also reduces the As(III) concentration below 10 μg/L in the product water, meeting the WHO standard.

  20. Effective As(III) Removal by A Multi-Charged Hydroacid Complex Draw Solute Facilitated Forward Osmosis-Membrane Distillation (FO-MD) Processes

    KAUST Repository

    Ge, Qingchun

    2016-01-29

    © 2016 American Chemical Society. Effective removal of As(III) from water by an oxalic acid complex with the formula of Na3[Cr(C2O4)3] (Na-Cr-OA) is demonstrated via an forward osmosis-membrane distillation (FO-MD) hybrid system in this study. Na-Cr-OA first proved its superiority as a draw solute with high water fluxes and negligible reverse fluxes in FO, then a systematic investigation of the Na-Cr-OA promoted FO process was conducted to ascertain the factors in As(III) removal. Relatively high water fluxes of 28 LMH under the FO mode and 74 LMH under the pressure retarded osmosis (PRO) mode were achieved when using a 1000 ppm As(III) solution as the feed and 1.0 M Na-Cr-OA as the draw solution at 60 °C. As(III) removal with a water recovery up to 21.6% (FO mode) and 48.3% (PRO mode) were also achieved in 2 h. An outstanding As(III) rejection with 30-3000 μg/L As(III) in the permeate was accomplished when As(III) feed solutions varied from 5 × 104 to 1 × 106 μg/L, superior to the best FO performance reported for As(III) removal. Incorporating MD into FO not only makes As(III) removal sustainable by reconcentrating the Na-Cr-OA solution simultaneously, but also reduces the As(III) concentration below 10 μg/L in the product water, meeting the WHO standard.

  1. Response of deep and shallow tropical maritime cumuli to large-scale processes

    Science.gov (United States)

    Yanai, M.; Chu, J.-H.; Stark, T. E.; Nitta, T.

    1976-01-01

    The bulk diagnostic method of Yanai et al. (1973) and a simplified version of the spectral diagnostic method of Nitta (1975) are used for a more quantitative evaluation of the response of various types of cumuliform clouds to large-scale processes, using the same data set in the Marshall Islands area for a 100-day period in 1956. The dependence of the cloud mass flux distribution on radiative cooling, large-scale vertical motion, and evaporation from the sea is examined. It is shown that typical radiative cooling rates in the tropics tend to produce a bimodal distribution of mass spectrum exhibiting deep and shallow clouds. The bimodal distribution is further enhanced when the large-scale vertical motion is upward, and a nearly unimodal distribution of shallow clouds prevails when the relative cooling is compensated by the heating due to the large-scale subsidence. Both deep and shallow clouds are modulated by large-scale disturbances. The primary role of surface evaporation is to maintain the moisture flux at the cloud base.

  2. Deep-inelastic processes: a workbench for large scale motion in nuclear matter

    International Nuclear Information System (INIS)

    Moretto, L.G.; Schmitt, R.P.

    1978-07-01

    The most prominent collective modes excited in deep-inelastic reactions are reviewed, and the natural hierarchy provided by their characteristic relaxation times is described. A model is presented which treats the relaxation of the mass asymmetry mode in terms of a diffusion process. Charge distributions and angular distributions as a function of Z calculated with this model are in good agreement with experimental data. An extension of this diffusion model which treats the transfer of energy and angular momentum in terms of particle transfer is described, and is successfully compared with experimental γ-ray multiplicities as a function of both Q-value and mass asymmetry. The problem of angular momentum transfer is again considered in connection with the sequential fission of heavy, deep-inelastic fragments and the excitation of collective modes in the exit channel is suggested. Lastly, the role of the giant E1 mode in the equilibration of the neutron-to-proton ratio is discussed. 14 figures, 39 references

  3. Deep-inelastic processes: a workbench for large scale motion in nuclear matter

    Energy Technology Data Exchange (ETDEWEB)

    Moretto, L.G.; Schmitt, R.P.

    1978-07-01

    The most prominent collective modes excited in deep-inelastic reactions are reviewed, and the natural hierarchy provided by their characteristic relaxation times is described. A model is presented which treats the relaxation of the mass asymmetry mode in terms of a diffusion process. Charge distributions and angular distributions as a function of Z calculated with this model are in good agreement with experimental data. An extension of this diffusion model which treats the transfer of energy and angular momentum in terms of particle transfer is described, and is successfully compared with experimental ..gamma..-ray multiplicities as a function of both Q-value and mass asymmetry. The problem of angular momentum transfer is again considered in connection with the sequential fission of heavy, deep-inelastic fragments and the excitation of collective modes in the exit channel is suggested. Lastly, the role of the giant E1 mode in the equilibration of the neutron-to-proton ratio is discussed. 14 figures, 39 references.

  4. A Sparse Auto Encoder Deep Process Neural Network Model and its Application

    Directory of Open Access Journals (Sweden)

    Xu Shaohua

    2017-01-01

    Full Text Available Aiming at the problem of time-varying signal pattern classification, a sparse auto-encoder deep process neural network (SAE-DPNN is proposed. The input of SAE-DPNN is time-varying process signal and the output is pattern category. It combines the time-varying signal classification method of process neural network (PNN and the data feature extraction and hierarchical sparse representation mechanism of sparse automatic encoder (SAE. Based on the feedforward PNN model, SAE-DPNN is constructed by stacking the process neurons, SAE network and softmax classifier. It can maintain the time-sequence and structure of the input signal, express and synthesize the process distribution characteristics of multidimensional time-varying signals and their combinations. SAE-DPNN improves the identification of complex features and distinguishes between different types of signals, realizes the direct classification of time-varying signals. In this paper, the feature extraction and representation mechanism of time-varying signal in SAE-DPNN are analyzed, and a specific learning algorithm is given. The experimental results verify the effectiveness of the model and algorithm.

  5. ON THE ISSUE OF IMPORT SUBSTITUTION OF DEEP PROCESSING PRODUCTS FROM GRAIN AND POTATO

    Directory of Open Access Journals (Sweden)

    N. R. Andreev

    2014-01-01

    Full Text Available Summary. The analysis of structure of starch containing raw materials processing in Russia Federation is provided in the article. There was noted an increase in volumes of corn and wheat processing, however the share of processed potato is still low (below 4%. It was established that Russian starch products and starch sweeteners are on the same level on quality as best European samples and they are very competitive. Market demand in crystalline glucose for food and medical purposes (over 30 thous. tons is fully covered by import. The volume of import of modified starches exceeds 80 % of total consumption. The biggest volume of import among native starches belongs to potato starch – over 60 %. The article provides suggestions on import substitution of mentioned starch products. The growth of starch production in Russia was accompanied by concentration of production at large enterprises. So, in 2013 over 90 % of glucose syrup was produced at six enterprises, over 80 % of dry starch – at five enterprises. Efficiency of corn and wheat processing into starch and starch products is achieved by production and selling of co-products (dry gluten, gluten, corn germ or corn oil, corn extract, feed products.Development of starch sweeteners production from starch could be achieved by expanding the consumption areas of different kinds of glucose syrup and production of glucose-fructose syrups as full substitute of sugar, providing import substitution of sugar, crystalline glucose of food and medicine purpose, deep processing of glucose into polyols (sorbit, maltit, polylactites, aminoacids.

  6. On astronomical drawing [1846

    Science.gov (United States)

    Smyth, Charles Piazzi

    Reprinted from the Memoirs of the Royal Astronomical Society 15, 1846, pp. 71-82. With annotations and illustrations added by Klaus Hentschel. The activities of the Astronomer Royal for Scotland, Charles Piazzi Smyth (1819-1900), include the triangulation of South African districts, landscape painting, day-to-day or tourist sketching, the engraving and lithographing of prominent architectural sites, the documentary photography of the Egyptian pyramids or the Tenerife Dragon tree, and `instant photographs' of the clouds above his retirement home in Clova, Ripon. His colorful records of the aurora polaris, and solar and terrestrial spectra all profited from his trained eye and his subtle mastery of the pen and the brush. As his paper on astronomical drawing, which we chose to reproduce in this volume, amply demonstrates, he was conversant in most of the print technology repertoire that the 19th century had to offer, and carefully selected the one most appropriate to each sujet. For instance, he chose mezzotint for the plates illustrating Maclear's observations of Halley's comet in 1835/36, so as to achieve a ``rich profundity of shadows, the deep obscurity of which is admirably adapted to reproduce those fine effects of chiaroscuro frequently found in works where the quantity of dark greatly predominates.'' The same expertise with which he tried to emulate Rembrandt's chiaroscuro effects he applied to assessing William and John Herschel's illustrations of nebulae, which appeared in print between 1811 and 1834. William Herschel's positive engraving, made partly by stippling and partly by a coarse mezzotint, receives sharp admonishment because of the visible ruled crossed lines in the background and the fact that ``the objects, which are also generally too light, [have] a much better definition than they really possess.'' On the other hand, John Herschel's illustration of nebulae and star clusters, given in negative, ``in which the lights are the darkest part of the

  7. Deep brain stimulation of nucleus accumbens region in alcoholism affects reward processing.

    Science.gov (United States)

    Heldmann, Marcus; Berding, Georg; Voges, Jürgen; Bogerts, Bernhard; Galazky, Imke; Müller, Ulf; Baillot, Gunther; Heinze, Hans-Jochen; Münte, Thomas F

    2012-01-01

    The influence of bilateral deep brain stimulation (DBS) of the nucleus nucleus (NAcc) on the processing of reward in a gambling paradigm was investigated using H(2)[(15)O]-PET (positron emission tomography) in a 38-year-old man treated for severe alcohol addiction. Behavioral data analysis revealed a less risky, more careful choice behavior under active DBS compared to DBS switched off. PET showed win- and loss-related activations in the paracingulate cortex, temporal poles, precuneus and hippocampus under active DBS, brain areas that have been implicated in action monitoring and behavioral control. Except for the temporal pole these activations were not seen when DBS was deactivated. These findings suggest that DBS of the NAcc may act partially by improving behavioral control.

  8. Diverging receptive and expressive word processing mechanisms in a deep dyslexic reader.

    Science.gov (United States)

    Ablinger, Irene; Radach, Ralph

    2016-01-29

    We report on KJ, a patient with acquired dyslexia due to cerebral artery infarction. He represents an unusually clear case of an "output" deep dyslexic reader, with a distinct pattern of pure semantic reading. According to current neuropsychological models of reading, the severity of this condition is directly related to the degree of impairment in semantic and phonological representations and the resulting imbalance in the interaction between the two word processing pathways. The present work sought to examine whether an innovative eye movement supported intervention combining lexical and segmental therapy would strengthen phonological processing and lead to an attenuation of the extreme semantic over-involvement in KJ's word identification process. Reading performance was assessed before (T1) between (T2) and after (T3) therapy using both analyses of linguistic errors and word viewing patterns. Therapy resulted in improved reading aloud accuracy along with a change in error distribution that suggested a return to more sequential reading. Interestingly, this was in contrast to the dynamics of moment-to-moment word processing, as eye movement analyses still suggested a predominantly holistic strategy, even at T3. So, in addition to documenting the success of the therapeutic intervention, our results call for a theoretically important conclusion: Real-time letter and word recognition routines should be considered separately from properties of the verbal output. Combining both perspectives may provide a promising strategy for future assessment and therapy evaluation. Copyright © 2015. Published by Elsevier Ltd.

  9. PyDBS: an automated image processing workflow for deep brain stimulation surgery.

    Science.gov (United States)

    D'Albis, Tiziano; Haegelen, Claire; Essert, Caroline; Fernández-Vidal, Sara; Lalys, Florent; Jannin, Pierre

    2015-02-01

    Deep brain stimulation (DBS) is a surgical procedure for treating motor-related neurological disorders. DBS clinical efficacy hinges on precise surgical planning and accurate electrode placement, which in turn call upon several image processing and visualization tasks, such as image registration, image segmentation, image fusion, and 3D visualization. These tasks are often performed by a heterogeneous set of software tools, which adopt differing formats and geometrical conventions and require patient-specific parameterization or interactive tuning. To overcome these issues, we introduce in this article PyDBS, a fully integrated and automated image processing workflow for DBS surgery. PyDBS consists of three image processing pipelines and three visualization modules assisting clinicians through the entire DBS surgical workflow, from the preoperative planning of electrode trajectories to the postoperative assessment of electrode placement. The system's robustness, speed, and accuracy were assessed by means of a retrospective validation, based on 92 clinical cases. The complete PyDBS workflow achieved satisfactory results in 92 % of tested cases, with a median processing time of 28 min per patient. The results obtained are compatible with the adoption of PyDBS in clinical practice.

  10. Deep Sequence Analysis of AgoshRNA Processing Reveals 3’ A Addition and Trimming

    Directory of Open Access Journals (Sweden)

    Alex Harwig

    2015-01-01

    Full Text Available The RNA interference (RNAi pathway, in which microprocessor and Dicer collaborate to process microRNAs (miRNA, was recently expanded by the description of alternative processing routes. In one of these noncanonical pathways, Dicer action is replaced by the Argonaute2 (Ago2 slicer function. It was recently shown that the stem-length of precursor-miRNA or short hairpin RNA (shRNA molecules is a major determinant for Dicer versus Ago2 processing. Here we present the results of a deep sequence study on the processing of shRNAs with different stem length and a top G·U wobble base pair (bp. This analysis revealed some unexpected properties of these so-called AgoshRNA molecules that are processed by Ago2 instead of Dicer. First, we confirmed the gradual shift from Dicer to Ago2 processing upon shortening of the hairpin length. Second, hairpins with a stem larger than 19 base pair are inefficiently cleaved by Ago2 and we noticed a shift in the cleavage site. Third, the introduction of a top G·U bp in a regular shRNA can promote Ago2-cleavage, which coincides with a loss of Ago2-loading of the Dicer-cleaved 3’ strand. Fourth, the Ago2-processed AgoshRNAs acquire a short 3’ tail of 1–3 A-nucleotides (nt and we present evidence that this product is subsequently trimmed by the poly(A-specific ribonuclease (PARN.

  11. Drawing Theory. An Introduction

    Directory of Open Access Journals (Sweden)

    Stefano Milani

    2014-08-01

    Full Text Available Nowadays, drawing practices seem to operate in a rather uncertain field that is typical of an in-between phase of disciplinary development and that needs to be addressed, if an ‘anticipated projection’ of the development of drawing is to be attempted. The field of drawing, as practice and discourse, seems to have entered an end-condition, where the celebration of the extensive production of drawings is combined with a certain fatigue in both its understanding and reflection. Even though the role of drawing is nowadays still regarded as the most common act of architecture, this understanding of drawing is hardly subject to critical inquiries, and, unfortunately, mostly limited to its instrumental role within the representation of the project.A common characteristic in all of the papers in this issue of Footprint is that a specific character of the theoretical field generated by drawing is the elaboration of the correlation between two epistemic regions. This singular character probably belongs to drawing’s structural duality of being simultaneously a simulacrum of a reality and reality itself, memory and anticipation, subject and object, by being in essence the measure of two different facets inherent to architectural thinking. Drawing not only gives consistency to the poles, rendering them architectural matter, but also literally (reconstructs them. At the same time, drawing formalizes the theoretical distance between the two.

  12. MiniDraw

    DEFF Research Database (Denmark)

    2018-01-01

    MiniDraw is a teaching-oriented 2D graphics direct manipulation framework in Java, inspired by JHotDraw. It is used in the book "Flexible, Reliable Software - using Patterns and Agile Development", by Henrik Bærbak Christensen, published by CRC Press 2010.......MiniDraw is a teaching-oriented 2D graphics direct manipulation framework in Java, inspired by JHotDraw. It is used in the book "Flexible, Reliable Software - using Patterns and Agile Development", by Henrik Bærbak Christensen, published by CRC Press 2010....

  13. Differentiated effects of deep brain stimulation and medication on somatosensory processing in Parkinson's disease.

    Science.gov (United States)

    Sridharan, Kousik Sarathy; Højlund, Andreas; Johnsen, Erik Lisbjerg; Sunde, Niels Aagaard; Johansen, Lars Gottfried; Beniczky, Sándor; Østergaard, Karen

    2017-07-01

    Deep brain stimulation (DBS) and dopaminergic medication effectively alleviate the motor symptoms in Parkinson's disease (PD) patients, but their effects on the sensory symptoms of PD are still not well understood. To explore early somatosensory processing in PD, we recorded magnetoencephalography (MEG) from thirteen DBS-treated PD patients and ten healthy controls during median nerve stimulation. PD patients were measured during DBS-treated, untreated and dopaminergic-medicated states. We focused on early cortical somatosensory processing as indexed by N20m, induced gamma augmentation (31-45Hz and 55-100Hz) and induced beta suppression (13-30Hz). PD patients' motor symptoms were assessed by UPDRS-III. Using Bayesian statistics, we found positive evidence for differentiated effects of treatments on the induced gamma augmentation (31-45Hz) with highest gamma in the dopaminergic-medicated state and lowest in the DBS-treated and untreated states. In contrast, UPDRS-III scores showed beneficial effects of both DBS and dopaminergic medication on the patients' motor symptoms. Furthermore, treatments did not affect the amplitude of N20m. Our results suggest differentiated effects of DBS and dopaminergic medication on cortical somatosensory processing in PD patients despite consistent ameliorating effects of both treatments on PD motor symptoms. The differentiated effect suggests differences in the effect mechanisms of the two treatments. Copyright © 2017 International Federation of Clinical Neurophysiology. Published by Elsevier B.V. All rights reserved.

  14. Analysing Children's Drawings: Applied Imagination

    Science.gov (United States)

    Bland, Derek

    2012-01-01

    This article centres on a research project in which freehand drawings provided a richly creative and colourful data source of children's imagined, ideal learning environments. Issues concerning the analysis of the visual data are discussed, in particular, how imaginative content was analysed and how the analytical process was dependent on an…

  15. TWRS system drawings and field verification

    International Nuclear Information System (INIS)

    Shepard, D.G.

    1995-01-01

    The Configuration Management Program combines the TWRS Labeling and O and M drawing and drawing verification programs. The combined program will produce system drawings for systems that are normally operated or have maintenance performed on the system, label individual pieces of equipment for proper identification, even if system drawings are not warranted, and perform verification of drawings that are identified as essential in Tank Farm Essential Drawing Plans. During fiscal year 1994, work was begun to label Tank Farm components and provide user friendly system based drawings for Tank Waste Remediation System (TWRS) operations and maintenance. During the first half of fiscal 1995, the field verification program continued to convert TWRS drawings into CAD format and verify the accuracy based on visual inspections. During the remainder of fiscal year 1995 these efforts will be combined into a single program providing system based drawings and field verification of TWRS equipment and facilities. This combined program for TWRS will include all active systems for tank farms. Operations will determine the extent of drawing and labeling requirements for single shell tanks, i.e. the electrical distribution, HVAC, leak detection, and the radiation monitoring system. The tasks required to meet these objectives, include the following: identify system boundaries or scope for drawing being verified; label equipment/components in the process systems with a unique Equipment Identification Number (EIN) per the TWRS Data Standard; develop system drawings that are coordinated by ''smart'' drawing numbers and/or drawing references as identified on H-14-020000; develop a Master Equipment List (MEL) multi-user data base application which will contain key information about equipment identified in the field; and field verify and release TWRS Operation and Maintenance (O and M) drawings

  16. Cross-frequency coupling in deep brain structures upon processing the painful sensory inputs.

    Science.gov (United States)

    Liu, C C; Chien, J H; Kim, J H; Chuang, Y F; Cheng, D T; Anderson, W S; Lenz, F A

    2015-09-10

    Cross-frequency coupling has been shown to be functionally significant in cortical information processing, potentially serving as a mechanism for integrating functionally relevant regions in the brain. In this study, we evaluate the hypothesis that pain-related gamma oscillatory responses are coupled with low-frequency oscillations in the frontal lobe, amygdala and hippocampus, areas known to have roles in pain processing. We delivered painful laser pulses to random locations on the dorsal hand of five patients with uncontrolled epilepsy requiring depth electrode implantation for seizure monitoring. Two blocks of 40 laser stimulations were delivered to each subject and the pain-intensity was controlled at five in a 0-10 scale by adjusting the energy level of the laser pulses. Local-field-potentials (LFPs) were recorded through bilaterally implanted depth electrode contacts to study the oscillatory responses upon processing the painful laser stimulations. Our results show that painful laser stimulations enhanced low-gamma (LH, 40-70 Hz) and high-gamma (HG, 70-110 Hz) oscillatory responses in the amygdala and hippocampal regions on the right hemisphere and these gamma responses were significantly coupled with the phases of theta (4-7 Hz) and alpha (8-1 2 Hz) rhythms during pain processing. Given the roles of these deep brain structures in emotion, these findings suggest that the oscillatory responses in these regions may play a role in integrating the affective component of pain, which may contribute to our understanding of the mechanisms underlying the affective information processing in humans. Copyright © 2015 IBRO. Published by Elsevier Ltd. All rights reserved.

  17. Deep frying

    NARCIS (Netherlands)

    Koerten, van K.N.

    2016-01-01

    Deep frying is one of the most used methods in the food processing industry. Though practically any food can be fried, French fries are probably the most well-known deep fried products. The popularity of French fries stems from their unique taste and texture, a crispy outside with a mealy soft

  18. Responding to Children's Drawings

    Science.gov (United States)

    Watts, Robert

    2010-01-01

    This article aims to explore the issues that face primary school teachers when responding to children's drawings. Assessment in art and design is an ongoing concern for teachers with limited experience and confidence in the area and, although children's drawings continue to be a focus of much research, the question of what it is that teachers say…

  19. Architecture, Drawing, Topology

    DEFF Research Database (Denmark)

    Meldgaard, Morten

    This book presents contributions of drawing and text along with their many relationalities from ontology to history and vice versa in a range of reflections on architecture, drawing and topology. We hope to thereby indicate the potential of the theme in understanding not only the architecture of ...

  20. Strict confluent drawing

    NARCIS (Netherlands)

    Eppstein, D.; Holten, D.H.R.; Löffler, M.; Nöllenburg, M.; Speckmann, B.; Verbeek, K.A.B.

    2013-01-01

    We define strict confluent drawing, a form of confluent drawing in which the existence of an edge is indicated by the presence of a smooth path through a system of arcs and junctions (without crossings), and in which such a path, if it exists, must be unique. We prove that it is NP-complete to

  1. Strict confluent drawing

    NARCIS (Netherlands)

    Eppstein, D.; Holten, D.; Löffler, M.; Nöllenburg, M.; Speckmann, B.; Verbeek, K.A.B.

    2016-01-01

    We define strict confluent drawing, a form of confluent drawing in which the existence of an edge is indicated by the presence of a smooth path through a system of arcs and junctions (without crossings), and in which such a path, if it exists, must be unique. We prove that it is NP-complete to

  2. DEEP LEARNING AND IMAGE PROCESSING FOR AUTOMATED CRACK DETECTION AND DEFECT MEASUREMENT IN UNDERGROUND STRUCTURES

    Directory of Open Access Journals (Sweden)

    F. Panella

    2018-05-01

    Full Text Available This work presents the combination of Deep-Learning (DL and image processing to produce an automated cracks recognition and defect measurement tool for civil structures. The authors focus on tunnel civil structures and survey and have developed an end to end tool for asset management of underground structures. In order to maintain the serviceability of tunnels, regular inspection is needed to assess their structural status. The traditional method of carrying out the survey is the visual inspection: simple, but slow and relatively expensive and the quality of the output depends on the ability and experience of the engineer as well as on the total workload (stress and tiredness may influence the ability to observe and record information. As a result of these issues, in the last decade there is the desire to automate the monitoring using new methods of inspection. The present paper has the goal of combining DL with traditional image processing to create a tool able to detect, locate and measure the structural defect.

  3. Virtual sampling in variational processing of Monte Carlo simulation in a deep neutron penetration problem

    International Nuclear Information System (INIS)

    Allagi, Mabruk O.; Lewins, Jeffery D.

    1999-01-01

    In a further study of virtually processed Monte Carlo estimates in neutron transport, a shielding problem has been studied. The use of virtual sampling to estimate the importance function at a certain point in the phase space depends on the presence of neutrons from the real source at that point. But in deep penetration problems, not many neutrons will reach regions far away from the source. In order to overcome this problem, two suggestions are considered: (1) virtual sampling is used as far as the real neutrons can reach, then fictitious sampling is introduced for the remaining regions, distributed in all the regions, or (2) only one fictitious source is placed where the real neutrons almost terminate and then virtual sampling is used in the same way as for the real source. Variational processing is again found to improve the Monte Carlo estimates, being best when using one fictitious source in the far regions with virtual sampling (option 2). When fictitious sources are used to estimate the importances in regions far away from the source, some optimization has to be performed for the proportion of fictitious to real sources, weighted against accuracy and computational costs. It has been found in this study that the optimum number of cells to be treated by fictitious sampling is problem dependent, but as a rule of thumb, fictitious sampling should be employed in regions where the number of neutrons from the real source fall below a specified limit for good statistics

  4. Groundwater Mixing Process Identification in Deep Mines Based on Hydrogeochemical Property Analysis

    Directory of Open Access Journals (Sweden)

    Bo Liu

    2016-12-01

    Full Text Available Karst collapse columns, as a potential water passageway for mine water inrush, are always considered a critical problem for the development of deep mining techniques. This study aims to identify the mixing process of groundwater deriving two different limestone karst-fissure aquifer systems. Based on analysis of mining groundwater hydrogeochemical properties, hydraulic connection between the karst-fissure objective aquifer systems was revealed. In this paper, piper diagram was used to calculate the mixing ratios at different sampling points in the aquifer systems, and PHREEQC Interactive model (Version 2.5, USGS, Reston, VA, USA, 2001 was applied to modify the mixing ratios and model the water–rock interactions during the mixing processes. The analysis results show that the highest mixing ratio is 0.905 in the C12 borehole that is located nearest to the #2 karst collapse column, and the mixing ratio decreases with the increase of the distance from the #2 karst collapse column. It demonstrated that groundwater of the two aquifers mixed through the passage of #2 karst collapse column. As a result, the proposed Piper-PHREEQC based method can provide accurate identification of karst collapse columns’ water conductivity, and can be applied to practical applications.

  5. Interplay of hard and soft physics in small x deep inelastic processes

    International Nuclear Information System (INIS)

    Abramowicz, H.

    1995-01-01

    Coherence phenomena, the increase with energy of coherence length and the nonuniversality of parton structure of the effective pomeron are explained. New hard phenomena directly calculable in QCD such as diffractive electroproduction of states with M 2 2 and the color transparency phenomenon as well as new options to measure the light-cone wave functions of various hadrons are considered. An analogue of Bjorken scaling is predicted for the diffractive electroproduction of ρ mesons at large momentum transfers and for the production of large rapidity gap events, as observed at HERA. A phenomenological QCD evolution equation is suggested to calculate the basic characteristics of the large rapidity gap events. The increase of parton densities at small x as well as new means to disentangle experimentally soft and hard physics are considered. We discuss constraints on the increase of deep inelastic amplitudes with Q 2 derived from the inconsistency of QCD predictions for inclusive and exclusive processes and from unitarity of the S matrix for collisions of wave packets. New ways to probe QCD physics of hard processes at large longitudinal distances and to answer the long standing problems on the origin of the pomeron are suggested. Unresolved problems and perspectives of small x physics are also outlined. (orig.)

  6. The impact of Parkinson's disease and subthalamic deep brain stimulation on reward processing.

    Science.gov (United States)

    Evens, Ricarda; Stankevich, Yuliya; Dshemuchadse, Maja; Storch, Alexander; Wolz, Martin; Reichmann, Heinz; Schlaepfer, Thomas E; Goschke, Thomas; Lueken, Ulrike

    2015-08-01

    Due to its position in cortico-subthalamic and cortico-striatal pathways, the subthalamic nucleus (STN) is considered to play a crucial role not only in motor, but also in cognitive and motivational functions. In the present study we aimed to characterize how different aspects of reward processing are affected by disease and deep brain stimulation of the STN (DBS-STN) in patients with idiopathic Parkinson's disease (PD). We compared 33 PD patients treated with DBS-STN under best medical treatment (DBS-on, medication-on) to 33 PD patients without DBS, but optimized pharmacological treatment and 34 age-matched healthy controls. We then investigated DBS-STN effects using a postoperative stimulation-on/ -off design. The task set included a delay discounting task, a task to assess changes in incentive salience attribution, and the Iowa Gambling Task. The presence of PD was associated with increased incentive salience attribution and devaluation of delayed rewards. Acute DBS-STN increased risky choices in the Iowa Gambling Task under DBS-on condition, but did not further affect incentive salience attribution or the evaluation of delayed rewards. Findings indicate that acute DBS-STN affects specific aspects of reward processing, including the weighting of gains and losses, while larger-scale effects of disease or medication are predominant in others reward-related functions. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Green Processing of Lignocellulosic Biomass and Its Derivatives in Deep Eutectic Solvents.

    Science.gov (United States)

    Tang, Xing; Zuo, Miao; Li, Zheng; Liu, Huai; Xiong, Caixia; Zeng, Xianhai; Sun, Yong; Hu, Lei; Liu, Shijie; Lei, Tingzhou; Lin, Lu

    2017-07-10

    The scientific community has been seeking cost-competitive and green solvents with good dissolving capacity for the valorization of lignocellulosic biomass. At this point, deep eutectic solvents (DESs) are currently emerging as a new class of promising solvents that are generally liquid eutectic mixtures formed by self-association (or hydrogen-bonding interaction) of two or three components. DESs are attractive solvents for the fractionation (or pretreatment) of lignocellulose and the valorization of lignin, owing to the high solubility of lignin in DESs. DESs are also employed as effective media for the modification of cellulose to afford functionalized cellulosic materials, such as cellulose nanocrystals. More interestingly, biomassderived carbohydrates, such as fructose, can be used as one of the constituents of DESs and then dehydrated to 5-hydroxymethylfurfural in high yield. In this review, a comprehensive summary of recent contribution of DESs to the processing of lignocellulosic biomass and its derivatives is provided. Moreover, further discussion about the challenges of the application of DESs in biomass processing is presented. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Poly(A)-tag deep sequencing data processing to extract poly(A) sites.

    Science.gov (United States)

    Wu, Xiaohui; Ji, Guoli; Li, Qingshun Quinn

    2015-01-01

    Polyadenylation [poly(A)] is an essential posttranscriptional processing step in the maturation of eukaryotic mRNA. The advent of next-generation sequencing (NGS) technology has offered feasible means to generate large-scale data and new opportunities for intensive study of polyadenylation, particularly deep sequencing of the transcriptome targeting the junction of 3'-UTR and the poly(A) tail of the transcript. To take advantage of this unprecedented amount of data, we present an automated workflow to identify polyadenylation sites by integrating NGS data cleaning, processing, mapping, normalizing, and clustering. In this pipeline, a series of Perl scripts are seamlessly integrated to iteratively map the single- or paired-end sequences to the reference genome. After mapping, the poly(A) tags (PATs) at the same genome coordinate are grouped into one cleavage site, and the internal priming artifacts removed. Then the ambiguous region is introduced to parse the genome annotation for cleavage site clustering. Finally, cleavage sites within a close range of 24 nucleotides and from different samples can be clustered into poly(A) clusters. This procedure could be used to identify thousands of reliable poly(A) clusters from millions of NGS sequences in different tissues or treatments.

  9. Search for QCD Instanton-Induced Processes in Deep-Inelastic Scattering at HERA

    CERN Document Server

    Adloff, C.; Andrieu, B.; Anthonis, T.; Astvatsatourov, A.; Babaev, A.; Bahr, J.; Baranov, P.; Barrelet, E.; Bartel, W.; Becker, J.; Beckingham, M.; Beglarian, A.; Behnke, O.; Beier, C.; Belousov, A.; Berger, C.; Berndt, T.; Bizot, J.C.; Bohme, J.; Boudry, V.; Braunschweig, W.; Brisson, V.; Broker, H.B.; Brown, D.P.; Bruckner, W.; Bruncko, D.; Busser, F.W.; Bunyatyan, A.; Burrage, A.; Buschhorn, G.; Bystritskaya, L.; Campbell, A.J.; Carli, T.; Caron, S.; Cassol-Brunner, F.; Clarke, D.; Collard, C.; Contreras, J.G.; Coppens, Y.R.; Coughlan, J.A.; Cousinou, M.C.; Cox, B.E.; Cozzika, G.; Cvach, J.; Dainton, J.B.; Dau, W.D.; Daum, K.; Davidsson, M.; Delcourt, B.; Delerue, N.; Demirchyan, R.; De Roeck, A.; De Wolf, E.A.; Diaconu, C.; Dingfelder, J.; Dixon, P.; Dodonov, V.; Dowell, J.D.; Droutskoi, A.; Dubak, A.; Duprel, C.; Eckerlin, Guenter; Eckstein, D.; Efremenko, V.; Egli, S.; Eichler, R.; Eisele, F.; Eisenhandler, E.; Ellerbrock, M.; Elsen, E.; Erdmann, M.; Erdmann, W.; Faulkner, P.J.W.; Favart, L.; Fedotov, A.; Felst, R.; Ferencei, J.; Ferron, S.; Fleischer, M.; Fleischmann, P.; Fleming, Y.H.; Flugge, G.; Fomenko, A.; Foresti, I.; Formanek, J.; Franke, G.; Frising, G.; Gabathuler, E.; Gabathuler, K.; Garvey, J.; Gassner, J.; Gayler, Joerg; Gerhards, R.; Gerlich, C.; Ghazaryan, Samvel; Goerlich, L.; Gogitidze, N.; Grab, C.; Grabski, V.; Grassler, H.; Greenshaw, T.; Grindhammer, Guenter; Hadig, T.; Haidt, D.; Hajduk, L.; Haller, J.; Haynes, W.J.; Heinemann, B.; Heinzelmann, G.; Henderson, R.C.W.; Hengstmann, S.; Henschel, H.; Heremans, R.; Herrera, G.; Herynek, I.; Hildebrandt, M.; Hilgers, M.; Hiller, K.H.; Hladky, J.; Hoting, P.; Hoffmann, D.; Horisberger, R.; Hovhannisyan, A.; Hurling, S.; Ibbotson, M.; Issever, C .; Jacquet, M.; Jaffre, M.; Janauschek, L.; Janssen, X.; Jemanov, V.; Jonsson, L.; Johnson, C.; Johnson, D.P.; Jones, M.A.S.; Jung, H.; Kant, D.; Kapichine, M.; Karlsson, M.; Karschnick, O.; Keil, F.; Keller, N.; Kennedy, J.; Kenyon, I.R.; Kermiche, S.; Kiesling, Christian M.; Kjellberg, P.; Klein, M.; Kleinwort, C.; Kluge, T.; Knies, G.; Koblitz, B.; Kolya, S.D.; Korbel, V.; Kostka, P.; Kotelnikov, S.K.; Koutouev, R.; Koutov, A.; Kroseberg, J.; Kruger, K.; Kuhr, T.; Kurca, T.; Lamb, D.; Landon, M.P.J.; Lange, W.; Lastovicka, T.; Laycock, P.; Lebailly, E.; Lebedev, A.; Leissner, B.; Lemrani, R.; Lendermann, V.; Levonian, S.; Lindstroem, M.; List, B.; Lobodzinska, E.; Lobodzinski, B.; Loginov, A.; Loktionova, N.; Lubimov, V.; Luders, S.; Luke, D.; Lytkin, L.; Malden, N.; Malinovski, E.; Malinovski, I.; Mangano, S.; Maracek, R.; Marage, P.; Marks, J.; Marshall, R.; Martyn, H.U.; Martyniak, J.; Maxfield, S.J.; Meer, D.; Mehta, A.; Meier, K.; Meyer, A.B.; Meyer, H.; Meyer, J.; Meyer, P.O.; Mikocki, S.; Milstead, D.; Mohrdieck, S.; Mondragon, M.N.; Moreau, F.; Morozov, A.; Morris, J.V.; Muller, K.; Murin, P.; Nagovizin, V.; Naroska, B.; Naumann, J.; Naumann, T.; Nellen, G.; Newman, Paul R.; Niebergall, F.; Niebuhr, C.; Nix, O.; Nowak, G.; Olsson, J.E.; Ozerov, D.; Panassik, V.; Pascaud, C.; Patel, G.D.; Peez, M.; Perez, E.; Petrukhin, A.; Phillips, J.P.; Pitzl, D.; Poschl, R.; Potachnikova, I.; Povh, B.; Radel, G.; Rauschenberger, J.; Reimer, P.; Reisert, B.; Reyna, D.; Risler, C.; Rizvi, E.; Robmann, P.; Roosen, R.; Rostovtsev, A.; Rusakov, S.; Rybicki, K.; Sankey, D.P.C.; Schatzel, S.; Scheins, J.; Schilling, F.P.; Schleper, P.; Schmidt, D.; Schmidt, S.; Schmitt, S.; Schneider, M.; Schoeffel, L.; Schoning, A.; Schorner, T.; Schroder, V.; Schultz-Coulon, H.C.; Schwanenberger, C.; Sedlak, K.; Sefkow, F.; Chekelian, V.; Sheviakov, I.; Shtarkov, L.N.; Sirois, Y.; Sloan, T.; Smirnov, P.; Soloviev, Y.; South, D.; Spaskov, V.; Specka, Arnd E.; Spitzer, H.; Stamen, R.; Stella, B.; Stiewe, J.; Strauch, I.; Straumann, U.; Swart, M.; Tchetchelnitski, S.; Thompson, Graham; Thompson, P.D.; Tobien, N.; Tomasz, F.; Traynor, D.; Truoel, Peter; Tsipolitis, G.; Tsurin, I.; Turnau, J.; Turney, J.E.; Tzamariudaki, E.; Udluft, S.; Uraev, A.; Urban, Marcel; Usik, A.; Valkar, S.; Valkarova, A.; Vallee, C.; Van Mechelen, P.; Vassiliev, S.; Vazdik, Y.; Vest, A.; Vichnevski, A.; Wacker, K.; Wagner, J.; Wallny, R.; Waugh, B.; Weber, G.; Wegener, D.; Werner, C.; Werner, N.; Wessels, M.; White, G.; Wiesand, S.; Wilksen, T.; Winde, M.; Winter, G.G.; Wissing, C.; Wobisch, M.; Woehrling, E.E.; Wunsch, E.; Wyatt, A.C.; Zacek, J.; Zalesak, J.; Zhang, Z.; Zhokin, A.; Zomer, F.; zur Nedden, M.

    2002-01-01

    Signals of QCD instanton-induced processes are searched for in deep-inelastic scattering (DIS) at the electron-proton collider HERA in a kinematic region defined by the Bjorken-scaling variables x > 10^(-3), 0.1 < y < 0.6 and photon virtualities 10 <= Q^2 < 100GeV^2. Several observables characterising hadronic final state properties of QCD instanton-induced events are exploited to identify a potentially instanton-enriched domain. While an excess of events with instanton-like topology over the expectation of the standard DIS background is observed it can not be claimed to be significant given the uncertainty of the simulation. Upper limits on the cross-section for instanton-induced processes of between 60pb and 1000pb are set dependent on the kinematic domain considered. The data do not exclude the cross-section predicted by instanton perturbation theory for small instanton sizes. At large instanton sizes a naive extrapolation of instanton perturbation theory yields a cross-section in the range of ...

  10. Characterization equipment essential drawing plan

    International Nuclear Information System (INIS)

    WILSON, G.W.

    1999-01-01

    The purpose of this document is to list the Characterization equipment drawings that are classified as Essential Drawings. Essential Drawings: Are those drawings identified by the facility staff as necessary to directly support the safe operation of the facility or equipment (HNF 1997a). The Characterization equipment drawings identified in this report are deemed essential drawings as defined in HNF-PRO-242, Engineering Drawing Requirements (HNF 1997a). These drawings will be prepared, revised, and maintained per HNF-PRO-440, Engineering Document Change Control (HNF 1997b). All other Characterization equipment drawings not identified in this document will be considered Support drawings until the Characterization Equipment Drawing Evaluation Report is completed

  11. Scientific drawing: an introduction to drawing as a language in fieldwork

    Directory of Open Access Journals (Sweden)

    José Mayor Iborra

    2013-11-01

    Full Text Available The scientific drawing understood as a universal language is a tool of undoubted documentary value as well as daily use in our field work of any professional who is with the need to register with graphics, a work process in which, need to process the drawing as coach and illustrator information. The drawings scientists have always had the vocation of fidelity and accuracy, in order to collect objective truths. The scientific drawing has been compressed and discriminating, as the reading order of the drawing through the line by providing a clear exposition that the photograph is not enough to achieve.

  12. Integrative and Deep Learning through a Learning Community: A Process View of Self

    Science.gov (United States)

    Mahoney, Sandra; Schamber, Jon

    2011-01-01

    This study investigated deep learning produced in a community of general education courses. Student speeches on liberal education were analyzed for discovering a grounded theory of ideas about self. The study found that learning communities cultivate deep, integrative learning that makes the value of a liberal education relevant to students.…

  13. Deep Processing Strategies and Critical Thinking: Developmental Trajectories Using Latent Growth Analyses

    Science.gov (United States)

    Phan, Huy P.

    2011-01-01

    The author explored the developmental courses of deep learning approach and critical thinking over a 2-year period. Latent growth curve modeling (LGM) procedures were used to test and trace the trajectories of both theoretical frameworks over time. Participants were 264 (119 women, 145 men) university undergraduates. The Deep Learning subscale of…

  14. Order of blood draw

    DEFF Research Database (Denmark)

    Cornes, Michael; van Dongen-Lases, Edmée; Grankvist, Kjell

    2017-01-01

    does occur if order of draw is not followed during blood collection and when performing venipuncture under less than ideal circumstances, thus putting patient safety at risk. Moreover, given that order of draw is not difficult to follow and knowing that ideal phlebotomy conditions and protocols...... Medicine Working Group for the Preanalytical Phase (EFLM WG-PRE) provides an overview and summary of the literature with regards to order of draw in venous blood collection. Given the evidence presented in this article, the EFLM WG-PRE herein concludes that a significant frequency of sample contamination...

  15. Methodology for balancing design and process tradeoffs for deep-subwavelength technologies

    Science.gov (United States)

    Graur, Ioana; Wagner, Tina; Ryan, Deborah; Chidambarrao, Dureseti; Kumaraswamy, Anand; Bickford, Jeanne; Styduhar, Mark; Wang, Lee

    2011-04-01

    For process development of deep-subwavelength technologies, it has become accepted practice to use model-based simulation to predict systematic and parametric failures. Increasingly, these techniques are being used by designers to ensure layout manufacturability, as an alternative to, or complement to, restrictive design rules. The benefit of model-based simulation tools in the design environment is that manufacturability problems are addressed in a design-aware way by making appropriate trade-offs, e.g., between overall chip density and manufacturing cost and yield. The paper shows how library elements and the full ASIC design flow benefit from eliminating hot spots and improving design robustness early in the design cycle. It demonstrates a path to yield optimization and first time right designs implemented in leading edge technologies. The approach described herein identifies those areas in the design that could benefit from being fixed early, leading to design updates and avoiding later design churn by careful selection of design sensitivities. This paper shows how to achieve this goal by using simulation tools incorporating various models from sparse to rigorously physical, pattern detection and pattern matching, checking and validating failure thresholds.

  16. Microbial redox processes in deep subsurface environments and the potential application of (perchlorate in oil reservoirs

    Directory of Open Access Journals (Sweden)

    Martin G Liebensteiner

    2014-09-01

    Full Text Available The ability of microorganisms to thrive under oxygen-free conditions in subsurface environments relies on the enzymatic reduction of oxidized elements, such as sulfate, ferric iron or CO2, coupled to the oxidation of inorganic or organic compounds. A broad phylogenetic and functional diversity of microorganisms from subsurface environments has been described using isolation-based and advanced molecular ecological techniques. The physiological groups reviewed here comprise iron-, manganese- and nitrate-reducing microorganisms. In the context of recent findings also the potential of chlorate and perchlorate [jointly termed (perchlorate] reduction in oil reservoirs will be discussed. Special attention is given to elevated temperatures that are predominant in the deep subsurface. Microbial reduction of (perchlorate is a thermodynamically favorable redox process, also at high temperature. However, knowledge about (perchlorate reduction at elevated temperatures is still scarce and restricted to members of the Firmicutes and the archaeon Archaeoglobus fulgidus. By analyzing the diversity and phylogenetic distribution of functional genes in (metagenome databases and combining this knowledge with extrapolations to earlier-made physiological observations we speculate on the potential of (perchlorate reduction in the subsurface and more precisely oil fields. In addition, the application of (perchlorate for bioremediation, souring control and microbial enhanced oil recovery are addressed.

  17. Hemispheric dissociation of reward processing in humans: insights from deep brain stimulation.

    Science.gov (United States)

    Palminteri, Stefano; Serra, Giulia; Buot, Anne; Schmidt, Liane; Welter, Marie-Laure; Pessiglione, Mathias

    2013-01-01

    Rewards have various effects on human behavior and multiple representations in the human brain. Behaviorally, rewards notably enhance response vigor in incentive motivation paradigms and bias subsequent choices in instrumental learning paradigms. Neurally, rewards affect activity in different fronto-striatal regions attached to different motor effectors, for instance in left and right hemispheres for the two hands. Here we address the question of whether manipulating reward-related brain activity has local or general effects, with respect to behavioral paradigms and motor effectors. Neuronal activity was manipulated in a single hemisphere using unilateral deep brain stimulation (DBS) in patients with Parkinson's disease. Results suggest that DBS amplifies the representation of reward magnitude within the targeted hemisphere, so as to affect the behavior of the contralateral hand specifically. These unilateral DBS effects on behavior include both boosting incentive motivation and biasing instrumental choices. Furthermore, using computational modeling we show that DBS effects on incentive motivation can predict DBS effects on instrumental learning (or vice versa). Thus, we demonstrate the feasibility of causally manipulating reward-related neuronal activity in humans, in a manner that is specific to a class of motor effectors but that generalizes to different computational processes. As these findings proved independent from therapeutic effects on parkinsonian motor symptoms, they might provide insight into DBS impact on non-motor disorders, such as apathy or hypomania. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. High resolution deep level transient spectroscopy and process-induced defects in silicon

    International Nuclear Information System (INIS)

    Evans-Freeman, J.H.; Emiroglu, D.; Vernon-Parry, K.D.

    2004-01-01

    High resolution, or Laplace, deep level transient spectroscopy (LDLTS) enables the identification of very closely spaced energetic levels in a semiconductor bandgap. DLTS may resolve peaks with a separation of tens of electron volts, but LDLTS can resolve defect energy separations as low as a few MeV. In this paper, we present results from LDLTS applied to ion implantation-induced defects in silicon, with particular emphasis on characterisation of end-of-range interstitial type defects. Silicon was implanted with a variety of ions from mass 28 to 166. A combination of LDLTS and direct capture cross-section measurements was employed to show that electrically active small extended defects were present in the as-implanted samples. Larger dislocations were then generated in Si by oxygenation to act as a control sample. These stacking faults had typical lengths of microns, and their electrical activity was subsequently characterised by LDLTS. This was to establish the sensitivity of LDLTS to defects whose carrier capture is characterised by a non-exponential filling process and an evolving band structure as carrier capture proceeds. The LDLTS spectra show several components in capacitance transients originating from both the end-of-range defects, and the stacking faults, and also clearly show that the carrier emission rates reduce as these extended defects fill with carriers. The end-of-range defects and the stacking faults are shown to have the same electrical behaviour

  19. 37 CFR 1.83 - Content of drawing.

    Science.gov (United States)

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Content of drawing. 1.83... COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions The Drawings § 1.83 Content of drawing. (a) The drawing in a nonprovisional application must show every feature of the...

  20. Does processing a shallow and a deep orthography produce different brain activity patterns? An ERP study conducted in Hebrew.

    Science.gov (United States)

    Bar-Kochva, Irit

    2011-01-01

    Orthographies range from shallow orthographies with transparent grapheme-phoneme relations, to deep orthographies, in which these relations are opaque. Two forms of script transcribe the Hebrew language: the shallow pointed script (with diacritics) and the deep unpointed script (without diacritics). This study was set out to examine whether the reading of these scripts evokes distinct brain activity. Preliminary results indicate distinct Event-related-potentials (ERPs). As an equivalent finding was absent when ERPs of non-orthographic stimuli with and without meaningless diacritics were compared, the results imply that print-specific aspects of processing account for the distinct activity elicited by the pointed and unpointed scripts.

  1. Drawings: Kozloduy NPP

    International Nuclear Information System (INIS)

    Boyadjiev, Z.

    1995-01-01

    This paper includes drawings of Kozloduy nuclear power plant needed for study for the seismic analysis and testing. It covers the list and schemes of safety and safety related systems for normal operation as well as protection and control systems

  2. Right Brain Drawing.

    Science.gov (United States)

    Whalen, Adryce C.

    1985-01-01

    The author describes activities of a weekly enrichment class providing right-brain tasks to gifted elementary students. Activities, which centered on artistic creativity, were taken from "Drawing On the Right Side of the Brain" by B. Edwards. (CL)

  3. Regional Variation of CH4 and N2 Production Processes in the Deep Aquifers of an Accretionary Prism.

    Science.gov (United States)

    Matsushita, Makoto; Ishikawa, Shugo; Nagai, Kazushige; Hirata, Yuichiro; Ozawa, Kunio; Mitsunobu, Satoshi; Kimura, Hiroyuki

    2016-09-29

    Accretionary prisms are mainly composed of ancient marine sediment scraped from the subducting oceanic plate at a convergent plate boundary. Large amounts of anaerobic groundwater and natural gas, mainly methane (CH4) and nitrogen gas (N2), are present in the deep aquifers associated with an accretionary prism; however, the origins of these gases are poorly understood. We herein revealed regional variations in CH4 and N2 production processes in deep aquifers in the accretionary prism in Southwest Japan, known as the Shimanto Belt. Stable carbon isotopic and microbiological analyses suggested that CH4 is produced through the non-biological thermal decomposition of organic matter in the deep aquifers in the coastal area near the convergent plate boundary, whereas a syntrophic consortium of hydrogen (H2)-producing fermentative bacteria and H2-utilizing methanogens contributes to the significant production of CH4 observed in deep aquifers in midland and mountainous areas associated with the accretionary prism. Our results also demonstrated that N2 production through the anaerobic oxidation of organic matter by denitrifying bacteria is particularly prevalent in deep aquifers in mountainous areas in which groundwater is affected by rainfall.

  4. Integrating shallow and deep knowledge in the design of an on-line process monitoring system

    Energy Technology Data Exchange (ETDEWEB)

    Gallanti, M.; Gilardoni, L.; Guida, G.; Stefanini, A.; Tomada, L.

    1989-01-01

    Monitoring and malfunctions diagnosis of complex industrial plants involves, in addition to shallow empirical knowledge about plant operation, also deep knowledge about structure and function. This paper presents the results obtained in the design and experimentation of PROP and PROP-2 systems, devoted to on-line monitoring and diagnosis of pollution phenomena in the cycle water of a thermal power plant. In particular, it focuses on PROP-2 architecture, with encompasses a four-level hierarchical knowledge base including both empirical knowledge and a deep model of the plant. Shallow knowledge is represented by production rules and event-graphs (a formalism for expressing procedural knowledge), while deep knowledge is expressed using a representation language based on the concept of component. One major contribution of the proposed approach has been to show in a running experimental system that a suitable blend of shallow and deep knowledge can offer substantial advantages over a single paradigm.

  5. Surface Improvement of Shafts by Turn-Assisted Deep Cold Rolling Process

    Directory of Open Access Journals (Sweden)

    Prabhu Raghavendra

    2016-01-01

    Full Text Available It is well recognized that mechanical surface enhancement methods can significantly improve the characteristics of highly-stressed metallic components. Deep cold rolling is one of such technique which is particularly attractive since it is possible to generate, near the surface, deep compressive residual stresses and work hardened layers while retaining a relatively smooth surface finish. In this paper, the effect of turn-assisted deep cold rolling on AISI 4140 steel is examined, with emphasis on the residual stress state. Based on the X-ray diffraction measurements, it is found that turn-assisted deep cold rolling can be quite effective in retarding the initiation and initial propagation of fatigue cracks in AISI 4140 steel.

  6. Rupture process of the 2013 Okhotsk deep mega earthquake from iterative backprojection and compress sensing methods

    Science.gov (United States)

    Qin, W.; Yin, J.; Yao, H.

    2013-12-01

    On May 24th 2013 a Mw 8.3 normal faulting earthquake occurred at a depth of approximately 600 km beneath the sea of Okhotsk, Russia. It is a rare mega earthquake that ever occurred at such a great depth. We use the time-domain iterative backprojection (IBP) method [1] and also the frequency-domain compressive sensing (CS) technique[2] to investigate the rupture process and energy radiation of this mega earthquake. We currently use the teleseismic P-wave data from about 350 stations of USArray. IBP is an improved method of the traditional backprojection method, which more accurately locates subevents (energy burst) during earthquake rupture and determines the rupture speeds. The total rupture duration of this earthquake is about 35 s with a nearly N-S rupture direction. We find that the rupture is bilateral in the beginning 15 seconds with slow rupture speeds: about 2.5km/s for the northward rupture and about 2 km/s for the southward rupture. After that, the northward rupture stopped while the rupture towards south continued. The average southward rupture speed between 20-35 s is approximately 5 km/s, lower than the shear wave speed (about 5.5 km/s) at the hypocenter depth. The total rupture length is about 140km, in a nearly N-S direction, with a southward rupture length about 100 km and a northward rupture length about 40 km. We also use the CS method, a sparse source inversion technique, to study the frequency-dependent seismic radiation of this mega earthquake. We observe clear along-strike frequency dependence of the spatial and temporal distribution of seismic radiation and rupture process. The results from both methods are generally similar. In the next step, we'll use data from dense arrays in southwest China and also global stations for further analysis in order to more comprehensively study the rupture process of this deep mega earthquake. Reference [1] Yao H, Shearer P M, Gerstoft P. Subevent location and rupture imaging using iterative backprojection for

  7. Tank farms essential drawing plan

    International Nuclear Information System (INIS)

    Domnoske-Rauch, L.A.

    1998-01-01

    The purpose of this document is to define criteria for selecting Essential Drawings, Support Drawings, and Controlled Print File (CPF) drawings and documents for facilities that are part of East and West Tank Farms. Also, the drawings and documents that meet the criteria are compiled separate listings. The Essential Drawing list and the Support Drawing list establish a priority for updating technical baseline drawings. The CPF drawings, denoted by an asterisk (*), defined the drawings and documents that Operations is required to maintain per the TWRS Administration Manual. The Routing Boards in Buildings 272-WA and 272-AW are not part of the CPF

  8. Interactions between superficial and deep dorsal horn spinal cord neurons in the processing of nociceptive information.

    Science.gov (United States)

    Petitjean, Hugues; Rodeau, Jean-Luc; Schlichter, Rémy

    2012-12-01

    In acute rat spinal cord slices, the application of capsaicin (5 μm, 90 s), an agonist of transient receptor potential vanilloid 1 receptors expressed by a subset of nociceptors that project to laminae I-II of the spinal cord dorsal horn, induced an increase in the frequency of spontaneous excitatory and spontaneous inhibitory postsynaptic currents in about half of the neurons in laminae II, III-IV and V. In the presence of tetrodotoxin, which blocks action potential generation and polysynaptic transmission, capsaicin increased the frequency of miniature excitatory postsynaptic currents in only 30% of lamina II neurons and had no effect on the frequency of miniature excitatory postsynaptic currents in laminae III-V or on the frequency of miniature inhibitory postsynaptic currents in laminae II-V. When the communication between lamina V and more superficial laminae was interrupted by performing a mechanical section between laminae IV and V, capsaicin induced an increase in spontaneous excitatory postsynaptic current frequency in laminae II-IV and an increase in spontaneous inhibitory postsynaptic current frequency in lamina II that were similar to those observed in intact slices. However, in laminae III-IV of transected slices, the increase in spontaneous inhibitory postsynaptic current frequency was virtually abolished. Our results indicate that nociceptive information conveyed by transient receptor potential vanilloid 1-expressing nociceptors is transmitted from lamina II to deeper laminae essentially by an excitatory pathway and that deep laminae exert a 'feedback' control over neurons in laminae III-IV by increasing inhibitory synaptic transmission in these laminae. Moreover, we provide evidence that laminae III-IV might play an important role in the processing of nociceptive information in the dorsal horn. © 2012 The Authors. European Journal of Neuroscience © 2012 Federation of European Neuroscience Societies and Blackwell Publishing Ltd.

  9. Qualifications of Bonding Process of Temperature Sensors to Deep-Space Missions

    Science.gov (United States)

    Ramesham, Rajeshuni; Kitiyakara, Amarit; Redick, Richard W., III; Sunada, Eric T.

    2011-01-01

    A process has been examined for bonding a platinum resistance thermometer (PRT) onto potential aerospace materials such as flat aluminum surfaces and a flexible copper tube to simulate coaxial cables for flight applications. Primarily, PRTs were inserted into a silver-plated copper braid to avoid stresses on the sensor while the sensor was attached with the braid to the base material for long-duration, deep-space missions. A1-1145/graphite composite (planar substrate) and copper tube have been used in this study to assess the reliability of PRT bonding materials. A flexible copper tube was chosen to simulate the coaxial cable to attach PRTs. The substrate materials were cleaned with acetone wipes to remove oils and contaminants. Later, the surface was also cleaned with ethyl alcohol and was air-dried. The materials were gently abraded and then were cleaned again the same way as previously mentioned. Initially, shielded (silver plated copper braid) PRT (type X) test articles were fabricated and cleaned. The base antenna material was pretreated and shielded, and CV-2566 NuSil silicone was used to attach the shielded PRT to the base material. The test articles were cured at room temperature and humidity for seven days. The resistance of the PRTs was continuously monitored during the thermal cycling, and the test articles were inspected prior to, at various intermediate steps during, and at the end of the thermal cycling as well. All of the PRTs survived three times the expected mission life for the JUNO project. No adhesion problems were observed in the PRT sensor area, or under the shielded PRT. Furthermore, the PRT resistance accurately tracked the thermal cycling of the chamber.

  10. [Cost-effectiveness of the deep vein thrombosis diagnosis process in primary care].

    Science.gov (United States)

    Fuentes Camps, Eva; Luis del Val García, José; Bellmunt Montoya, Sergi; Hmimina Hmimina, Sara; Gómez Jabalera, Efren; Muñoz Pérez, Miguel Ángel

    2016-04-01

    To analyse the cost effectiveness of the application of diagnostic algorithms in patients with a first episode of suspected deep vein thrombosis (DVT) in Primary Care compared with systematic referral to specialised centres. Observational, cross-sectional, analytical study. Patients from hospital emergency rooms referred from Primary Care to complete clinical evaluation and diagnosis. A total of 138 patients with symptoms of a first episode of DVT were recruited; 22 were excluded (no Primary Care report, symptoms for more than 30 days, anticoagulant treatment, and previous DVT). Of the 116 patients finally included, 61% women and the mean age was 71 years. Variables from the Wells and Oudega clinical probability scales, D-dimer (portable and hospital), Doppler ultrasound, and direct costs generated by the three algorithms analysed: all patients were referred systematically, referral according to Wells and Oudega scale. DVT was confirmed in 18.9%. The two clinical probability scales showed a sensitivity of 100% (95% CI: 85.1 to 100) and a specificity of about 40%. With the application of the scales, one third of all referrals to hospital emergency rooms could have been avoided (P<.001). The diagnostic cost could have been reduced by € 8,620 according to Oudega and € 9,741 according to Wells, per 100 patients visited. The application of diagnostic algorithms when a DVT is suspected could lead to better diagnostic management by physicians, and a more cost effective process. Copyright © 2015 Elsevier España, S.L.U. All rights reserved.

  11. Evaluation of processes controlling the geochemical constituents in deep groundwater in Bangladesh: Spatial variability on arsenic and boron enrichment

    International Nuclear Information System (INIS)

    Halim, M.A.; Majumder, R.K.; Nessa, S.A.; Hiroshiro, Y.; Sasaki, K.; Saha, B.B.; Saepuloh, A.; Jinno, K.

    2010-01-01

    Forty-six deep groundwater samples from highly arsenic affected areas in Bangladesh were analyzed in order to evaluate the processes controlling geochemical constituents in the deep aquifer system. Spatial trends of solutes, geochemical modeling and principal component analysis indicate that carbonate dissolution, silicate weathering and ion exchange control the major-ion chemistry. The groundwater is dominantly of Na-Cl type brackish water. Approximately 17% of the examined groundwaters exhibit As concentrations higher than the maximum acceptable limit of 10 μg/L for drinking water. Strong correlation (R 2 = 0.67) of Fe with dissolved organic carbon (DOC) and positive saturation index of siderite suggests that the reductive dissolution of Fe-oxyhydroxide in presence of organic matter is considered to be the dominant process to release high content of Fe (median 0.31 mg/L) in the deep aquifer. In contrast, As is not correlated with Fe and DOC. Boron concentration in the 26% samples exceeds the standard limit of 500 μg/L, for water intended for human consumption. Negative relationships of B/Cl ratio with Cl and boron with Na/Ca ratio demonstrate the boron in deep groundwater is accompanied by brackish water and cation exchange within the clayey sediments.

  12. Monitoring deep geodynamic processes within Vrancea intermediate-depth seismic zone by geodetic means

    Science.gov (United States)

    Besutiu, Lucian; Zlagnean, Luminita

    2015-04-01

    Background Located in the bending zone of East Carpathians, the so-called Vrancea zone is one of the most active seismic regions in Europe. Despite many years of international research, its intermediate-depth seismicity within full intra-continental environment still represents a challenge of the 21st century. Infrastructure In the attempt to join the above-mentioned efforts, the Solid Earth Dynamics Department (SEDD) in the Institute of Geodynamics of the Romanian Academy has developed a special research infrastructure, mainly devoted to gravity and space geodesy observations. A geodetic network covering the epicentre area of the intermediate-depth earthquakes has been designed and implemented for monitoring deep geodynamic processes and their surface echoes. Within each base-station of the above-mentioned network, a still-reinforced concrete pillar allows for high accuracy repeated gravity and GPS determinations. Results Starting from some results of the previously run CERGOP and UNIGRACE European programmes, to which additional SEDD repeated field campaigns were added, an unusual geodynamic behaviour has been revealed in the area. 1) Crust deformation: unlike the overall uprising of East Carpathians, as a result of denudation followed by erosion, their SE bending zone, with Vrancea epicentre area exhibits a slight subsidence. 2) Gravity change: more than 200 microgals non-tidal gravity decrease over a 20 years time-span has been noticed within the subsiding area. Extended observations showed the gravity lowering as a nowadays continuing process. Interpretation This strange combination of topography subsidence and gravity lowering has been interpreted in terms of crust stretching in the Vrancea epicentre zone due to the gravity pull created by densification of the lower crust as a result of phase-transform processes taking place in the lithospheric compartment sunken into the upper mantle. The occurrence of crust earthquakes with vertical-extension focal

  13. Deep brain stimulation reveals emotional impact processing in ventromedial prefrontal cortex

    DEFF Research Database (Denmark)

    Gjedde, Albert; Geday, Jacob

    2009-01-01

    We tested the hypothesis that modulation of monoaminergic tone with deep-brain stimulation (DBS) of subthalamic nucleus would reveal a site of reactivity in the ventromedial prefrontal cortex that we previously identified by modulating serotonergic and noradrenergic mechanisms by blocking serotonin......-noradrenaline reuptake sites. We tested the hypothesis in patients with Parkinson's disease in whom we had measured the changes of blood flow everywhere in the brain associated with the deep brain stimulation of the subthalamic nucleus. We determined the emotional reactivity of the patients as the average impact...

  14. Hydrochemical evaluation and identification of geochemical processes in the shallow and deep wells in the Ramganga Sub-Basin, India.

    Science.gov (United States)

    Rajmohan, Natarajan; Patel, Neelam; Singh, Gaurav; Amarasinghe, Upali A

    2017-09-01

    Groundwater samples were collected from 44 wells in the Ramganga Sub-Basin (RSB), India, and analysed for major ions, nutrients and trace metals. The primary goal of this study is to evaluate the hydrochemistry and to identify the geochemical processes that govern the water chemistry in the shallow and deep tube wells in the study area using geochemical methods. The knowledge of changes in hydrochemistry of the aquifers is important for both groundwater recharge and use in the region. This study found that there are substantial differences of water chemistry between shallow and deep wells. In the shallow wells, the average concentrations of total dissolved solid (TDS), Na, K, Ca, Mg, HCO 3 , Cl, SO 4 , NO 3 , PO 4 , F, Cu, Mn, Fe and Cr are twofold higher than the deep wells. The concentrations of dissolved silica in the groundwater do not vary with the depth, which implies that the variation in the water chemistry is not due to mineral dissolution alone. Major ion ratios and saturation indices suggest that the water chemistry is predominantly controlled by dissolution of carbonate minerals, silicate weathering and ion exchange reactions. Thermodynamic evaluation (ion activity ratios and stability filed diagrams) indicates that the kaolinite and gibbsite controlled the water chemistry in the both shallow and deep wells. In addition, the groundwater chemistry in the shallow wells is affected by the vertical infiltration of contaminated water from surface contamination sources and nitrification process. In the deep wells, absence of NO 3 and low concentrations of Cl, SO 4 , PO 4 and F imply the role of regional flow and denitrification in the groundwater. Results concluded that proper management plan is necessary to protect the shallow aquifer in the RSB since shallow aquifer pumping is less expensive than the deeper one.

  15. Canada's deep geological repository for used nuclear fuel - update on the site evaluation process and interweaving of aboriginal traditional knowledge

    International Nuclear Information System (INIS)

    Watts, B.; Belfadhel, M.B.; Facella, J.

    2015-01-01

    The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for the long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository (DGR) in a suitable crystalline or sedimentary rock formation. In May 2010, the NWMO initiated a nine-step site selection process to seek an informed and willing community to host Canada's deep geological repository. As of April 2015, twenty-two communities expressed interest in learning more about the project. This paper provides an update on the site evaluation process and describes the approach, methods and criteria used in the assessments, focusing on geological and community well-being studies. Engagement and field activities to interweave Aboriginal Traditional Knowledge with western science are also discussed. (author)

  16. Position-specific automated processing of V3 env ultra-deep pyrosequencing data for predicting HIV-1 tropism.

    Science.gov (United States)

    Jeanne, Nicolas; Saliou, Adrien; Carcenac, Romain; Lefebvre, Caroline; Dubois, Martine; Cazabat, Michelle; Nicot, Florence; Loiseau, Claire; Raymond, Stéphanie; Izopet, Jacques; Delobel, Pierre

    2015-11-20

    HIV-1 coreceptor usage must be accurately determined before starting CCR5 antagonist-based treatment as the presence of undetected minor CXCR4-using variants can cause subsequent virological failure. Ultra-deep pyrosequencing of HIV-1 V3 env allows to detect low levels of CXCR4-using variants that current genotypic approaches miss. However, the computation of the mass of sequence data and the need to identify true minor variants while excluding artifactual sequences generated during amplification and ultra-deep pyrosequencing is rate-limiting. Arbitrary fixed cut-offs below which minor variants are discarded are currently used but the errors generated during ultra-deep pyrosequencing are sequence-dependant rather than random. We have developed an automated processing of HIV-1 V3 env ultra-deep pyrosequencing data that uses biological filters to discard artifactual or non-functional V3 sequences followed by statistical filters to determine position-specific sensitivity thresholds, rather than arbitrary fixed cut-offs. It allows to retain authentic sequences with point mutations at V3 positions of interest and discard artifactual ones with accurate sensitivity thresholds.

  17. Deep ocean fluxes and their link to surface ocean processes and the biological pump

    Digital Repository Service at National Institute of Oceanography (India)

    Rixen, T.; Guptha, M.V.S.; Ittekkot, V.

    's role as a reservoir for atmospheric CO sub(2).The results show a pronounced monsoon-driven seasonality with enhanced organic carbon fluxes into the deep-sea during the SW Monsoon and during the early and late NE Monsoon north of 10 degrees N...

  18. Regge behaviour and Bjorken scaling for deep-inelastic lepton-hadron scattering process

    International Nuclear Information System (INIS)

    Tran Huu Phat

    1976-01-01

    Within the framework of the Jost-Lehmann-Dyson (JLD) representation and the renormalization-group (RG) equation, it is shown that either the RG technique is not applicable to deep-inelastic phenomena or Regge behaviour and Bjorken scaling for structure functions do not coexist. (author)

  19. Deep and Surface Processing of Instructor's Feedback in an Online Course

    Science.gov (United States)

    Huang, Kun; Ge, Xun; Law, Victor

    2017-01-01

    This study investigated the characteristics of deep and surface approaches to learning in online students' responses to instructor's qualitative feedback given to a multi-stage, ill-structured design project. Further, the study examined the relationships between approaches to learning and two learner characteristics: epistemic beliefs (EB) and…

  20. Process-based approach for the detection of deep gas invading the surface

    Science.gov (United States)

    Romanak, Katherine; Bennett, Philip C.

    2017-05-09

    The present invention includes a method for determining the level of deep gas in a near surface formation that includes: measuring CO.sub.2, O.sub.2, CH.sub.4, and N.sub.2 levels in percent by volume from one or more surface or near surface geological samples; adding the water vapor content to the measured CO.sub.2, O.sub.2, CH.sub.4, and N.sub.2 levels in percent by volume; normalizing the gas mixture to 100% by volume or 1 atmospheric total pressure; and determining the ratios of: O.sub.2 versus CO.sub.2 to distinguish in-situ vadose zone CO.sub.2 from exogenous deep leakage CO.sub.2; CO.sub.2 versus N.sub.2 to distinguish whether CO.sub.2 is being removed from the near surface formation or CO.sub.2 is added from an exogenous deep leakage input; or CO.sub.2 versus N.sub.2/O.sub.2 to determine the degree of oxygen influx, consumption, or both; wherein the ratios are indicative of natural in situ CO.sub.2 or CO.sub.2 from the exogenous deep leakage input.

  1. Auto-Encoder based Deep Learning for Surface Electromyography Signal Processing

    Directory of Open Access Journals (Sweden)

    Marwa Farouk Ibrahim Ibrahim

    2018-01-01

    Full Text Available Feature extraction is taking a very vital and essential part of bio-signal processing. We need to choose one of two paths to identify and select features in any system. The most popular track is engineering handcrafted, which mainly depends on the user experience and the field of application. While the other path is feature learning, which depends on training the system on recognising and picking the best features that match the application. The main concept of feature learning is to create a model that is expected to be able to learn the best features without any human intervention instead of recourse the traditional methods for feature extraction or reduction and avoid dealing with feature extraction that depends on researcher experience. In this paper, Auto-Encoder will be utilised as a feature learning algorithm to practice the recommended model to excerpt the useful features from the surface electromyography signal. Deep learning method will be suggested by using Auto-Encoder to learn features. Wavelet Packet, Spectrogram, and Wavelet will be employed to represent the surface electromyography signal in our recommended model. Then, the newly represented bio-signal will be fed to stacked autoencoder (2 stages to learn features and finally, the behaviour of the proposed algorithm will be estimated by hiring different classifiers such as Extreme Learning Machine, Support Vector Machine, and SoftMax Layer. The Rectified Linear Unit (ReLU will be created as an activation function for extreme learning machine classifier besides existing functions such as sigmoid and radial basis function. ReLU will show a better classification ability than sigmoid and Radial basis function (RBF for wavelet, Wavelet scale 5 and wavelet packet signal representations implemented techniques. ReLU will illustrate better classification ability, as an activation function, than sigmoid and poorer than RBF for spectrogram signal representation. Both confidence interval and

  2. Mechanical Drawing and Design.

    Science.gov (United States)

    Mikulsky, Marilyn; McEnaney, Walter K.

    A syllabus is provided for a comprehensive foundation course in mechanical drawing and design for grades 9, 10, 11, or 12 that is prerequisite to advanced elective courses. Introductory materials include course objectives, an overview of basic concepts, and guidelines for implementation. Brief discussions of and suggestions for the areas of design…

  3. Drawing Hospital Foodscapes

    DEFF Research Database (Denmark)

    Tvedebrink, Tenna Doktor Olsen; Fisker, Anna Marie; Kirkegaard, Poul Henning

    This poster presents a series of drawings depicting the initial considerations made with the Ph.D. project for an improved ‘Interior Design for Food’ in a Danish hospital ward. The project concerns a study on the ontological and symbolic interrelationship possibly existing between food...

  4. Drawing the Line

    DEFF Research Database (Denmark)

    Holm, Isak Winkel

    2016-01-01

    of judgement that distinguishes between the inside and outside of a political community, between citizens and zombies. Second, the chapter focuses on the rhetorics applied to draw the line between rights-bearers and the rightless. ‘Prophetic’ speech, echoing the language of the Old Testament prophets, is vital...

  5. Bernard Tschumi Draws Architecture!

    Directory of Open Access Journals (Sweden)

    Gevork Hartoonian

    2014-08-01

    Full Text Available Bernard Tschumi’s delineation prepared for the Museu de Arte Contemporânea provides the starting point for this essay, which discusses the historicity of drawing and highlights the horizontality and the verticality that structure architecture’s contrast with the pictorial realm. Juxtaposing a freehand sketch with the digital image of the same project, Tschumi moves to address the paradox concerning the position of the body and drawing. This drawing also speaks for the reversal in the position of the body brought about by digital reproductivity.The reversal alludes to Tschumi’s theorization of architecture in terms of space and event. These, I will argue, are anticipated in The Manhattan Transcripts (1981 where a set of freehand drawings is used to evoke a filmic mood wherein the image is projected parallel to the spectator’s seated position. The essay goes further, suggesting that the theatricality permeating the present architecture is part of the shift from horizontality to the painterly, and yet the phenomenon is not merely a technical issue. Rather, it alludes to architecture’s dialogical rapport with painting at work since the Renaissance.

  6. Drawing experts have better visual memory while drawing

    NARCIS (Netherlands)

    Perdreau, F.A.G.; Cavanagh, P.

    2015-01-01

    Drawing involves frequent shifts of gaze between the original and the drawing and visual memory helps compare the original object and the drawing across these gaze shifts while creating and correcting the drawing. It remains unclear whether this memory encodes all of the object or only the features

  7. Drawings between Sensory Appeal and Cultural Code

    DEFF Research Database (Denmark)

    Nielsen, Anne Maj

    to the drawing child in ways that affect the drawing. This is important to take into consideration in research. Sensory appeal and cultural codes in analysis and practice Children’s perception and visual experiences contribute to the construction and transformation of meanings and narratives as they are mediated...... to the drawing child in ways that affect the drawing and the mediation of meaning. This should be taken into consideration in research. The aim of this paper is to qualify analysis of drawings as data in empirical research and to reflect upon opportunities for aesthetic learning processes in psycho....... & Nielsen, A.M. (Eds.) Æstetiske læreprocesser – i teori og praksis. (pp. 192 – 220). København: Billesoe & Baltzer. Fink-Jensen, K. (2007). Attunement and Bodily Dialogues in Music Education. Philosophy of Music Education Review, 15, no 1, 53 - 68. Keller, C. & Keller, J.D. (1993). Thinking and acting...

  8. Semantic knowledge for histopathological image analysis: from ontologies to processing portals and deep learning

    Science.gov (United States)

    Kergosien, Yannick L.; Racoceanu, Daniel

    2017-11-01

    , major changes are also to be expected for the relation of human diagnosis to machine based procedures. Improving on a former imaging platform which used a local knowledge base and a reasoning engine to combine image processing modules into higher level tasks, we propose a framework where different actors of the histopathology imaging world can cooperate using web services - exchanging knowledge as well as imaging services - and where the results of such collaborations on diagnostic related tasks can be evaluated in international challenges such as those recently organized for mitosis detection, nuclear atypia, or tissue architecture in the context of cancer grading. This framework is likely to offer an effective context-guidance and traceability to Deep Learning approaches, with an interesting promising perspective given by the multi-task learning (MTL) paradigm, distinguished by its applicability to several different learning algorithms, its non- reliance on specialized architectures and the promising results demonstrated, in particular towards the problem of weak supervision-, an issue found when direct links from pathology terms in reports to corresponding regions within images are missing.

  9. Deep borehole disposition of surplus fissile materials-The site selection process

    International Nuclear Information System (INIS)

    Heiken, G.; WoldeGabriel, G.; Morley, R.; Plannerer, H.

    1996-01-01

    One option for disposing of excess weapons plutonium is to place it near the base of deep boreholes in stable crystalline rocks. The technology exists to immediately begin the design of this means of disposition and there are many attractive sites available within the conterminous US. The borehole system utilizes mainly natural barriers to preven migration of Pu and U to the Earth's surface. Careful site selection ensures favorable geologic conditions that provide natural long-lived migration barriers; they include deep, extremely stable rock formations, strongly reducing brines that exhibit increasing salinity with depth, and most importantly, demonstrated isolation or non-communication of deep fluids with the biosphere for millions of years. This isolation is the most important characteristic, with the other conditions mainly being those that will enhance the potential of locating and maintaining the isolated zones. Candidate sites will probably be located on the craton in very old Precambrian crystalline rocks, most likely the center of a granitic pluton. The sites will be located in tectonically stable areas with no recent volcanic or seismic activity, and situated away from tectonic features that might become active in the near geologic future

  10. Survival of Penicillium spp. conidia during deep-frying and baking steps of frozen chicken nuggets processing.

    Science.gov (United States)

    Wigmann, Évelin Francine; Moreira, Rafael Chelala; Alvarenga, Verônica Ortiz; Sant'Ana, Anderson S; Copetti, Marina Venturini

    2016-05-01

    This study aimed at determining whether Penicillium spp. strains could survive through the heat treatment applied during the processing of frozen chicken nuggets. Firstly, it was found that the conidia of Penicillium were not able to survive the heat shock in phosphate buffer at pH 7.2 in thermal death tubes (TDT) at 80 °C/30 min. Subsequently, each Penicillium strain was inoculated in frozen chicken nuggets, which were subjected to the following treatments: i) only deep frying (frying oil at 195-200 °C), ii) only baking (120-130 °C until the internal temperature reached 70 °C) and iii) deep frying followed by baking (frying oil temperature of 195-200 °C and baking temperature of 120-130 °C, until the internal temperature reached 70 °C). The results indicated that Penicillium polonicum NGT 23/12, Penicillium commune NGT 16/12, Penicillium solitum NGT 30/12 and Penicillium crustosum NGT 51/12 were able to survive after the combined treatment (deep frying followed by baking) when inoculated in chicken nuggets. P. polonicum NGT 23/12 was the most resistant strain to the combined treatment (deep frying and baking), as its population was reduced by 3 log cycles CFU/g, when the internal temperature reached 78 °C after 10 min and 30 s of baking. The present data show that if Penicillium spp. is present in high numbers in raw materials, such as breading flours, it will survive the thermal processing applied during chicken nuggets production. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Draw the Line!

    DEFF Research Database (Denmark)

    present proceedings from the UPGEM conference "Draw the Line!" in Copenhagen May 2008. The proceedings include contributions by UPGEM researchers, conference speeches by other researchers, politicians and gender equality officers in which they relate their work and research with the research done in UPGEM......Draw the Line! International Conference, Copenhagen 2008 Papers, proceedings and recommendations is the second publication of the international three year long project "Understanding Puzzles in the Gendered European Map" (UPGEM), which is financed by the European Commission. In this publication we....... The UPGEM research has previously been published in national reports from each of the partner countries (Denmark, Estonia, Finland, Italy and Poland). In these individual national reports of universities as workplaces for male and female researchers we discuss scientific cultures in physics embedded...

  12. Probabilistic design of aluminum sheet drawing for reduced risk of wrinkling and fracture

    International Nuclear Information System (INIS)

    Zhang Wenfeng; Shivpuri, Rajiv

    2009-01-01

    Often, sheet drawing processes are designed to provide the geometry of the final part, and then the process parameters such as blank dimensions, blank holder forces (BHFs), press strokes and interface friction are designed and controlled to provide the greatest drawability (largest depth of draw without violating the wrinkling and thinning constraints). The exclusion of inherent process variations in this design can often lead to process designs that are unreliable and uncontrollable. In this paper, a general multi-criteria design approach is presented to quantify the uncertainties and to incorporate them into the response surface method (RSM) based model so as to conduct probabilistic optimization. A surrogate RSM model of the process mechanics is generated using FEM-based high-fidelity models and design of experiments (DOEs), and a simple linear weighted approach is used to formulate the objective function or the quality index (QI). To demonstrate this approach, deep drawing of an aluminum Hishida part is analyzed. With the predetermined blank shape, tooling design and fixed drawing depth, a probabilistic design (PD) is successfully carried out to find the optimal combination of BHF and friction coefficient under variation of material properties. The results show that with the probabilistic approach, the QI improved by 42% over the traditional deterministic design (DD). It also shows that by further reducing the variation of friction coefficient to 2%, the QI will improve further to 98.97%

  13. Physicochemical studies on sunflower oil blended with cold pressed tiger nut oil during deep frying process

    Directory of Open Access Journals (Sweden)

    Ali Rehab, F. M.

    2012-10-01

    Full Text Available Sunflower oils were blended with different levels of cold pressed tiger nut oil. Blended oils were obtained by mixing tiger nut oil with sunflower oil at the volume ratios of 0:100, 10: 90, 20: 80, 30: 70, 40: 60, 50:50 and 100: 0. The effects of deep frying on physico-chemical parameters (Free Fatty Acid (FFA, Peroxide Value (PV, thiobarbituric acid value (TBA, iodine value, Total Polar Compounds (TPC, color and viscosity were evaluated over 30 hours of the frying process. The total phenolic content of native oils was determined. GLC analysis was performed to illustrate the fatty acid composition of sunflower oil, tiger nut oil and binary mixtures of them as well as their oxidation rates. The pure and blended oils were heated at 180 °C ± 5 °C, then frozen French fried potatoes were fried every 30 min. Oil samples were taken every 5 h and the entire continuous frying period was 30 h. The results showed that fresh sunflower oil had significantly the highest value of COX (7.25; while tiger nut oil had significantly the lowest (2.24. Mixing sunflower oil with different levels of tiger nut oil led to an increase in its stability against oxidation. The phenolic content of cold pressed tiger nut oil was about 3.3 times as high as that of sunflower oil. The analytical data showed that the lowest deterioration during the frying process occurred in tiger nut oil and the highest in sunflower. The changes in the physico-chemical parameters were controlled and significantly (P < 0.05 decreased when tiger nut /sunflower oil (W/W proportions were varied between 20/80 to 50/50. The obtained results indicate that mixing sunflower oil with cold pressed tiger nut oil increased the stability and hence improved the quality of sunflower oil during the frying process.

    Aceites de girasol se mezclaron con diferentes niveles de aceite de chufa prensado en frío. Se obtuvieron mezclas de aceite de chufa con girasol en las proporciones: 0:100, 10: 90, 20: 80, 30

  14. Linear stories in Carlo Scarpa's architectural drawings

    DEFF Research Database (Denmark)

    Dayer, Carolina

    2017-01-01

    , an architect guides the viewer’s imagination into another not-yet-real world that is projected much like divinatory practices of reading palms or tarot cards. The magic-real field of facts and fictions coexisting in one realm can be understood as a confabulation. A confabulation brings together both fact...... close reading of the drawings has been made despite the thousands of drawings the architect constructed. Scarpa’s drawings, like confabulations, are places where many realities simultaneously coexist but all constitute one reality in a linear process, linear understood not as a straight, nor predictable...

  15. Process for selecting a site for Canada's deep geological repository for used nuclear fuel

    International Nuclear Information System (INIS)

    Facella, J.; Belfadhel, M.B.

    2011-01-01

    The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management, the approach selected by the Government of Canada for long-term management of used nuclear fuel waste generated by Canadian nuclear reactors. The ultimate objective of Adaptive Phased Management is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable crystalline or sedimentary rock formation at a depth of about 500m. The repository will consist of a series of access and service shafts and a series of tunnels leading to placement rooms where used fuel will be placed and sealed in competent rock using a multi-barrier system which includes long lived specially designed containers, sealing materials such as bentonite and the rock itself. The used fuel will be monitored throughout all phases of implementation and will also remain retrievable for an extended period of time. In May 2010, the NWMO published the site selection process that serves as the road map to decision-making on the location for the deep geological repository. NWMO initiated the process with a first stage that invites communities to learn more about the project and the site selection process. NWMO is actively building awareness of the project and, on request of communities, is delivering briefings, supporting community capacity building and undertaking high-level screenings of site suitability. The paper provides a brief description of: Adaptive Phased Management including the deep geological repository which is its ultimate goal, and the design of the site selection process, and importantly the approach to assessing the suitability of sites from both a social and technical perspective. The paper will outline how NWMO sought to develop a socially-acceptable site selection process as a firm foundation for future decisions on siting. Through a two-year collaborative process, NWMO sought to understand the expectations of

  16. Canada's Deep Geological Repository for Used Nuclear Fuel - Geo-scientific Site Evaluation Process - 13117

    Energy Technology Data Exchange (ETDEWEB)

    Blyth, Alec; Ben Belfadhel, Mahrez; Hirschorn, Sarah; Hamilton, Duncan; McKelvie, Jennifer [Nuclear Waste Management Organization, 22 St. Clair Avenue East, Toronto, Ontario M4T 2S3 (Canada)

    2013-07-01

    The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management (APM), the approach selected by the Government of Canada for long-term management of used nuclear fuel generated by Canadian nuclear reactors. The ultimate objective of APM is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable rock formation at a depth of approximately 500 meters (m) (1,640 feet [ft]). In May 2010, the NWMO published a nine-step site selection process that serves as the road map to decision-making on the location for the deep geological repository. The safety and appropriateness of any potential site will be assessed against a number of factors, both technical and social in nature. The selected site will be one that can be demonstrated to be able to safely contain and isolate used nuclear fuel, protecting humans and the environment over the very long term. The geo-scientific suitability of potential candidate sites will be assessed in a stepwise manner following a progressive and thorough site evaluation process that addresses a series of geo-scientific factors revolving around five safety functions. The geo-scientific site evaluation process includes: Initial Screenings; Preliminary Assessments; and Detailed Site Evaluations. As of November 2012, 22 communities have entered the site selection process (three in northern Saskatchewan and 18 in northwestern and southwestern Ontario). (authors)

  17. Evaluating the Generalization Value of Process-based Models in a Deep-in-time Machine Learning framework

    Science.gov (United States)

    Shen, C.; Fang, K.

    2017-12-01

    Deep Learning (DL) methods have made revolutionary strides in recent years. A core value proposition of DL is that abstract notions and patterns can be extracted purely from data, without the need for domain expertise. Process-based models (PBM), on the other hand, can be regarded as repositories of human knowledge or hypotheses about how systems function. Here, through computational examples, we argue that there is merit in integrating PBMs with DL due to the imbalance and lack of data in many situations, especially in hydrology. We trained a deep-in-time neural network, the Long Short-Term Memory (LSTM), to learn soil moisture dynamics from Soil Moisture Active Passive (SMAP) Level 3 product. We show that when PBM solutions are integrated into LSTM, the network is able to better generalize across regions. LSTM is able to better utilize PBM solutions than simpler statistical methods. Our results suggest PBMs have generalization value which should be carefully assessed and utilized. We also emphasize that when properly regularized, the deep network is robust and is of superior testing performance compared to simpler methods.

  18. Deep inelastic lepton-hadron processes in gauge models with massive vector gluons

    International Nuclear Information System (INIS)

    Morozov, P.T.; Stamenov, D.B.

    1978-01-01

    Considered is a class of strong interaction models in which the interactions between coloured quarks are mediated by massive neutral vector gluons. All the vector gluons acquire masses by the Higgs mechanism. These models are not asymptotically free. The effective gauge coupling constant anti α vanishes asymptotically, and the effective quartic coupling constant anti h tends to a finite asymptotic value. The behaviour of the moments of the deep inelastic lepton-hadron structure functions is analyzed. It is shown that the Bjorken scaling is violated by powers of logarithms

  19. Deep smarts.

    Science.gov (United States)

    Leonard, Dorothy; Swap, Walter

    2004-09-01

    When a person sizes up a complex situation and rapidly comes to a decision that proves to be not just good but brilliant, you think, "That was smart." After you watch him do this a few times, you realize you're in the presence of something special. It's not raw brainpower, though that helps. It's not emotional intelligence, either, though that, too, is often involved. It's deep smarts. Deep smarts are not philosophical--they're not"wisdom" in that sense, but they're as close to wisdom as business gets. You see them in the manager who understands when and how to move into a new international market, in the executive who knows just what kind of talk to give when her organization is in crisis, in the technician who can track a product failure back to an interaction between independently produced elements. These are people whose knowledge would be hard to purchase on the open market. Their insight is based on know-how more than on know-what; it comprises a system view as well as expertise in individual areas. Because deep smarts are experienced based and often context specific, they can't be produced overnight or readily imported into an organization. It takes years for an individual to develop them--and no time at all for an organization to lose them when a valued veteran walks out the door. They can be taught, however, with the right techniques. Drawing on their forthcoming book Deep Smarts, Dorothy Leonard and Walter Swap say the best way to transfer such expertise to novices--and, on a larger scale, to make individual knowledge institutional--isn't through PowerPoint slides, a Web site of best practices, online training, project reports, or lectures. Rather, the sage needs to teach the neophyte individually how to draw wisdom from experience. Companies have to be willing to dedicate time and effort to such extensive training, but the investment more than pays for itself.

  20. Influence of fertilizer draw solution properties on the process performance and microbial community structure in a side-stream anaerobic fertilizer-drawn forward osmosis - ultrafiltration bioreactor.

    Science.gov (United States)

    Kim, Youngjin; Li, Sheng; Chekli, Laura; Phuntsho, Sherub; Ghaffour, Noreddine; Leiknes, TorOve; Shon, Ho Kyong

    2017-09-01

    In this study, a side-stream anaerobic fertilizer-drawn forward osmosis (FDFO) and ultrafiltration (UF) membrane bioreactor (MBR) hybrid system was proposed and operated for 55days. The FDFO performance was first investigated in terms of flux decline with various fertilizers draw solution. Flux decline was very severe with all fertilizers due to the absence of aeration and the sticky property of sludge. Flux recovery by physical cleaning varied significantly amongst tested fertilizers which seriously affected biofouling in FDFO via reverse salt flux (RSF). Besides, RSF had a significant impact on nutrient accumulation in the bioreactor. These results indicated that nutrient accumulation negatively influenced the anaerobic activity. To elucidate these phenomena, bacterial and archaeal community structures were analyzed by pyrosequencing. Results showed that bacterial community structure was affected by fertilizer properties with less impact on archaeal community structure, which resulted in a reduction in biogas production and an increase in nitrogen content. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Influence of fertilizer draw solution properties on the process performance and microbial community structure in a side-stream anaerobic fertilizer-drawn forward osmosis – ultrafiltration bioreactor

    KAUST Repository

    Kim, Youngjin

    2017-02-27

    In this study, a side-stream anaerobic fertilizer-drawn forward osmosis (FDFO) and ultrafiltration (UF) membrane bioreactor (MBR) hybrid system was proposed and operated for 55 days. The FDFO performance was first investigated in terms of flux decline with various fertilizers draw solution. Flux decline was very severe with all fertilizers due to the absence of aeration and the sticky property of sludge. Flux recovery by physical cleaning varied significantly amongst tested fertilizers which seriously affected biofouling in FDFO via reverse salt flux (RSF). Besides, RSF had a significant impact on nutrient accumulation in the bioreactor. These results indicated that nutrient accumulation negatively influenced the anaerobic activity. To elucidate these phenomena, bacterial and archaeal community structures were analyzed by pyrosequencing. Results showed that bacterial community structure was affected by fertilizer properties with less impact on archaeal community structure, which resulted in a reduction in biogas production and an increase in nitrogen content.

  2. Slainless steel tube drawing on a mandrel

    International Nuclear Information System (INIS)

    Sokolovskij, V.I.; Parshin, V.S.; Veshkurtsev, V.I.

    1976-01-01

    A new technique for drawing stainless pipes on a mandrel has been developed at the Ural Polytechnical Institute. The method involves metal surfacing with a salt melt and results in stretching equal to 2.0. The use of such metal coats as lubrication sublayers makes possible repeated drawing with and without a mandrel. In both cases, the process does not involve intermediate heat treatment and/or any additional preparation of the surface

  3. PARAMETRIC DRAWINGS VS. AUTOLISP

    OpenAIRE

    PRUNĂ Liviu; SLONOVSCHI Andrei

    2015-01-01

    In this paper the authors make a critical analysis of the advantages offered by the parametric drawing use by comparison with the AutoLISP computer programs used when it comes about the parametric design. Studying and analysing these two work models the authors have got to some ideas and conclusions which should be considered in the moment in that someone must to decide if it is the case to elaborate a software, using the AutoLISP language, or to establish the base rules that must be followed...

  4. 37 CFR 1.85 - Corrections to drawings.

    Science.gov (United States)

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Corrections to drawings. 1.85... COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions The Drawings § 1.85 Corrections to drawings. (a) A utility or plant application will not be placed on the files for examination...

  5. 37 CFR 1.81 - Drawings required in patent application.

    Science.gov (United States)

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Drawings required in patent..., DEPARTMENT OF COMMERCE GENERAL RULES OF PRACTICE IN PATENT CASES National Processing Provisions The Drawings § 1.81 Drawings required in patent application. (a) The applicant for a patent is required to furnish...

  6. Deep repository - Engineered barrier system. Erosion and sealing processes in tunnel backfill materials investigated in laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Sanden, Torbjoern; Boergesson, Lennart; Dueck, Ann; Goudarzi, Reza; Loennqvist, Margareta (Clay Technology AB, Lund (Sweden))

    2008-12-15

    SKB in Sweden and Posiva in Finland are developing and plan to implement similar disposal concepts for the final disposal of spent nuclear fuel. Co-operation and joint development work between Posiva and SKB with the overall objective to develop backfill concepts and techniques for sealing and closure of the repository have been going on for several years. The investigation described in this report is intended to acquire more knowledge regarding the behavior of some of the candidate backfilling materials. Blocks made of three different materials (Friedland clay, Asha 230 or a bentonite/ballast 30/70 mixture) as well as different bentonite pellets have been examined. The backfill materials will be exposed to an environment simulating that in a tunnel, with high relative humidity and water inflow from the rock. The processes and properties investigated are: 1. Erosion properties of blocks and pellets (Friedland blocks, MX-80 pellets, Cebogel QSE pellets, Minelco and Friedland granules). 2. Displacements of blocks after emplacement in a deposition drift (Blocks of Friedland, Asha 230 and Mixture 30/70). 3. The ability of these materials to seal a leaking in-situ cast plug cement/rock but also other fractures in the rock (MX-80 pellets). 4. The self healing ability after a piping scenario (Blocks of Friedland, Asha 230 Mixture 30/70 and also MX-80 pellets). 5. Swelling and cracking of the compacted backfill blocks caused by relative humidity. The erosion properties of Friedland blocks were also investigated in Phase 2 of the joint SKBPosiva project 'Backfilling and Closure of the Deep Repository, BACLO, which included laboratory scale experiments. In this phase of the project (3) some completing tests were performed with new blocks produced for different field tests. These blocks had a lower density than intended and this has an influence on the erosion properties measured. The erosion properties of MX-80 pellets were also investigated earlier in the project but

  7. Drawing evaluation report for sampling equipment drawings; TOPICAL

    International Nuclear Information System (INIS)

    WILSON, G.W.

    1999-01-01

    This document presents the results of a task to evaluate Tank Waste Remediation System (TWRS) sampling equipment drawings and identifies drawings category as either essential, support, or general drawings. This report completes the drawing evaluation task as outlined in Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation (Wilson, 1997). The scope of this report is limited to an evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the TRWS Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, and all core sampling equipment (see LMHC Task Order 304). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Light Duty Utility Arm (LDUA), Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The LDUA drawings are addressed in the Characterization Equipment Essential Drawings (HNF 1998). The Cone Penetrometer system drawings which are vendor drawings (not H- series) is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and were not included in the original scope for this evaluation and will be addressed in the evaluation update scheduled for fiscal year 1999

  8. Left-right asymmetry for pion and kaon production in the semi-inclusive deep-inelastic scattering process

    International Nuclear Information System (INIS)

    Sun, Bo; She, Jun; Zhang, Bing; Mao, Ya-Jun; Ma, Bo-Qiang

    2010-01-01

    We analyze the left-right asymmetry in the semi-inclusive deep-inelastic scattering (SIDIS) process without introducing any weighting functions. With the current theoretical understanding, we find that the Sivers effect plays a key role in our analysis. We use the latest parametrization of the Sivers and fragmentation functions to reanalyze the π ± production process and find that the results are sensitive to the parametrization. We also extend our calculation on the K ± production, which can help us know more about the Sivers distribution of the sea quarks and the unfavored fragmentation processes. HERMES kinematics with a proton target, COMPASS kinematics with a proton, deuteron, and neutron target (the information on the neutron target can be effectively extracted from the 3 He target), and JLab kinematics (both 6 GeV and 12 GeV) with a proton and neutron target are considered in our paper. (orig.)

  9. A graph rewriting programming language for graph drawing

    OpenAIRE

    Rodgers, Peter

    1998-01-01

    This paper describes Grrr, a prototype visual graph drawing tool. Previously there were no visual languages for programming graph drawing algorithms despite the inherently visual nature of the process. The languages which gave a diagrammatic view of graphs were not computationally complete and so could not be used to implement complex graph drawing algorithms. Hence current graph drawing tools are all text based. Recent developments in graph rewriting systems have produced computationally com...

  10. Microbial processes in North Atlantic pelagic sediments, and potential risks of deep-sea waste disposal

    International Nuclear Information System (INIS)

    Bolliger, R.; Hanselmann, K.W.; Bachofen, R.

    1989-01-01

    From the results for waste disposal on deep sea sediments, it was concluded: As waste canisters are buried in the sediment to a depth of 15 to 20 cm, they are in contact with the zone that contains the highest potential bacterial activity through a relatively large surface. An input of oxidizable organic matter to the sediment surface zone will stimulate microbial activity and therefore increase the risk for solubilization and redistribution of elements in the ocean water. Waste canisters lying on the sediment surface cut off the oxygen supply from the ocean water and ease the shift to anaerobiosis. This initiates microbial activities through which metals are changed into their mobile species as a consequence of the altered environmental redox potential. The risk for steel corrosion by hydrogen sulfide, which could be produced by sulfate reducing bacteria, is minimal since this physiological group is not active in the North Atlantic sediments examined

  11. Sensitivity analysis of a light gas oil deep hydrodesulfurization process via catalytic distillation

    Energy Technology Data Exchange (ETDEWEB)

    Rosales-Quintero, A.; Vargas-Villamil, F.D. [Prog. de Matematicas Aplicadas y Computacion, Instituto Mexicano del Petroleo, Eje Central Lazaro Cardenas 152, Mexico, D.F. 07330 (Mexico); Arce-Medina, E. [Instituto Politecnico Nacional, ESIQIE, Ed. 8 Col. Lindavista, Mexico, D.F. 07738 (Mexico)

    2008-01-30

    In this work, a sensitivity analysis of a light gas oil deep hydrodesulfurization catalytic distillation column is presented. The aim is to evaluate the effects of various parameters and operating conditions on the organic sulfur compound elimination by using a realistic light gas oil fraction. The hydrocarbons are modeled using pseudocompounds, while the organic sulfur compounds are modeled using model compounds, i.e., dibenzothiophene (DBT) and 4,6-dimethyl dibenzothiophene (4,6-DMDBT). These are among the most refractive sulfur compounds present in the oil fractions. A sensitivity analysis is discussed for the reflux ratio, bottom flow rate, condenser temperature, hydrogen and gas oil feed stages, catalyst loading, the reactive, stripping, and rectifying stages, feed disturbances, and multiple feeds. The results give insight into the qualitative effect of some of the operating variables and disturbances on organic sulfur elimination. In addition, they show that special attention must be given to the bottom flow rate and LGO feed rate control. (author)

  12. Fundamentals of a moderate thermocracking-deep deasphalting combined process of Karamay vacuum residue

    Energy Technology Data Exchange (ETDEWEB)

    Zhiming, X; Tonghua, L.; Suogi, Z.; Renan, W. [University of Petroleum, State Key Laboratory of Heavy Oil Processing, Beijing (China); Lailong, L.; Zhen, L. [Karamay Petrochemical Company, Petrochemical Research Institute, Karamay (China)

    2004-07-01

    Thermocracking of heavy oil vacuum residue was carried out to determine the optimum conditions for the thermal cracking of Karamay vacuum residue prior to coke formation. The vacuum residue and the cracked residue after distillation were separated using supercritical fluid extraction and fractionation techniques. Sixteen and thirteen fractions and non-extractable end cuts respectively were separated, and their properties, compositions and average structures determined. Solubility parameters of the end cuts were measured, and those of the fractions calculated. The solubility parameter of the end cut of distilled residue was found to have greatly increased. It was determined that when the difference of the end cut and the extractable fractions amounts to 6.37MPa1/2, in the case of Karamay vacuum residue coke will deposit under thermocracking conditions. Based on the results of a series of solvent deep deasphalting experiments, a scheme for vacuum residue thermocracking and deasphalting of the cracked residue was proposed.

  13. Enhancing observation by drawing: Alveolinids models by Manfred Reichel (1896-1984)

    Science.gov (United States)

    Leria, Maria

    2017-04-01

    Graphic representation is a fundamental tool in morphological studies, as paleontology. A paradigmatic example is the alveolinid drawings of Prof. Manfred Reichel (1896-1984). Thanks to these drawings his research on foraminifera, had an important impact on micropaleontology. Manfred Reichel studied Fine Arts, but later he began a scientific career on biological sciences and becoming a professor in micropaleontology, at the Geological and Paleontological Institute of the University of Basel, Switzerland. His background in art had a benefit in his scientific production, especially with the extremely complex foraminiferal structures. By means of illustrations, inspired by the French naturalists, he was able to solve the most complex internal architecture of forams. His drawings display foraminifera's internal 3D structure in such a comprehensible way that has not been improved using modern techniques. His work has been used by different generations of paleontologist to understand the internal architecture of forams and are still used today. The aim of this study is to analyze the process that Reichel followed to create some of his most representative drawings. This study is based on the examination of a selection of Reichel's drawings (n>40) held at the Natural History Museum in Basel. In addition, his family and students have been interviewed supplying useful information to understand how he applied his artistic skills to teach and research. This study illustrates the steps followed by Reichel in the creation of a drawing of alveolinid. The process represents the transformation of the morphological data from 2D images (polished rock sections) into a comprehensible 3D image. A description of the process of observation, comparison, sketches and studies, concluding with the final three-dimensional drawing is shown. The results show that that the classical convention in drawing is still and irreplaceable tool in natural sciences, because it allows to define aspects that

  14. Evaluation of Workability on the Microstructure and Mechanical Property of Modified 9Cr-2W Steel for Fuel Cladding by Cold Drawing Process and Intermediate Heat Treatment Condition

    Directory of Open Access Journals (Sweden)

    Hyeong-Min Heo

    2018-03-01

    Full Text Available In this study, we evaluated the cold drawing workability of two kinds of modified 9Cr-2W steel containing different contents of boron and nitrogen depending on the temperature and time of normalizing and tempering treatments. Using ring compression tests at room temperature, the effect of intermediate heat treatment condition on workability was investigated. It was found that the prior austenite grain size can be changed by the austenite transformation and that the grain size increases with increasing temperature during normalizing heat treatment. Alloy B and Alloy N showed different patterns after normalizing heat treatment. Alloy N had higher stress than Alloy B, and the reduction in alloy N increased while the reduction in alloy B decreased. Alloy B showed a larger number of initially formed cracks and a larger average crack length than Alloy N. Crack length and number increased proportionally in Alloy B as the stress increased. Alloy B had lower crack resistance than Alloy N due to boron segregation.

  15. Photometric redshifts for the next generation of deep radio continuum surveys - II. Gaussian processes and hybrid estimates

    Science.gov (United States)

    Duncan, Kenneth J.; Jarvis, Matt J.; Brown, Michael J. I.; Röttgering, Huub J. A.

    2018-04-01

    Building on the first paper in this series (Duncan et al. 2018), we present a study investigating the performance of Gaussian process photometric redshift (photo-z) estimates for galaxies and active galactic nuclei detected in deep radio continuum surveys. A Gaussian process redshift code is used to produce photo-z estimates targeting specific subsets of both the AGN population - infrared, X-ray and optically selected AGN - and the general galaxy population. The new estimates for the AGN population are found to perform significantly better at z > 1 than the template-based photo-z estimates presented in our previous study. Our new photo-z estimates are then combined with template estimates through hierarchical Bayesian combination to produce a hybrid consensus estimate that outperforms both of the individual methods across all source types. Photo-z estimates for radio sources that are X-ray sources or optical/IR AGN are significantly improved in comparison to previous template-only estimates - with outlier fractions and robust scatter reduced by up to a factor of ˜4. The ability of our method to combine the strengths of the two input photo-z techniques and the large improvements we observe illustrate its potential for enabling future exploitation of deep radio continuum surveys for both the study of galaxy and black hole co-evolution and for cosmological studies.

  16. Review on chemical processes around the facilities in deep underground and study on numerical approach to evaluate them

    International Nuclear Information System (INIS)

    Sawada, Masataka

    2003-01-01

    The facilities for radioactive waste repositories are constructed in deep underground. Various chemical reactions including microbial activities may affect the long-term performance of the barrier system. An advancement of the evaluation method for the long-term behavior of barrier materials is desired. One of the efficient approaches is numerical simulation based on modeling of chemical processes. In the first part of this report, chemical processes and microbial reactions that can affect the performance of facilities in deep underground are reviewed. For example, dissolution and precipitation of minerals composing bentonite and rock are caused by highly alkaline water from cementitious materials. Numerical approaches to the chemical processes are also studied. Most chemical processes are reactions between groundwater (or solutes in it) and minerals composing barrier materials. So they can be simulated by coupled reaction rate transport analyses. Some analysis codes are developed and applied to problems in radioactive waste disposal. Microbial reaction rate can be modeled using the growth equation of microorganisms. In order to evaluate the performance of the barrier system after altered by chemical processes, not only the change in composition but also properties of altered materials is required to be obtained as output of numerical simulation. If the relationships between reaction rate and material properties are obtained, time history and spatial distribution of material properties can also be obtained by the coupled reaction rate transport analysis. At present, modeling study on the relationships between them is not sufficient, and obtaining such relationships using both theoretical and experimental approaches are also an important research target. (author)

  17. Czech Children's Drawing of Nature

    Science.gov (United States)

    Yilmaz, Zuhal; Kubiatko, Milan; Topal, Hatice

    2012-01-01

    Do world children draw nature pictures in a certain way? Range of mountains in the background, a sun, couple clouds, a river rising from mountains. Is this type of drawing universal in the way these nature items are organized on a drawing paper? The sample size from Czech Republic included 33 participants from two kindergartens. They were 5 and 6…

  18. THE MAIN CHARACTERISTICS OF LUBRICATION FOR WIRE DRAWING FOR METAL CORD, THEIR INFLUENCE ON DRAWING QUALITY

    Directory of Open Access Journals (Sweden)

    A. A. Truhanovich

    2008-01-01

    Full Text Available The physical-chemical characteristics of lubrications for dry wiredrawing are examined. The connection of some parameters with quality of both the drawing process and finished wire is shown.

  19. Marine litter on the floor of deep submarine canyons of the Northwestern Mediterranean Sea: The role of hydrodynamic processes

    Science.gov (United States)

    Tubau, Xavier; Canals, Miquel; Lastras, Galderic; Rayo, Xavier; Rivera, Jesus; Amblas, David

    2015-05-01

    Marine litter represents a widespread type of pollution in the World's Oceans. This study is based on direct observation of the seafloor by means of Remotely Operated Vehicle (ROV) dives and reports litter abundance, type and distribution in three large submarine canyons of the NW Mediterranean Sea, namely Cap de Creus, La Fonera and Blanes canyons. Our ultimate objective is establishing the links between active hydrodynamic processes and litter distribution, thus going beyond previous, essentially descriptive studies. Litter was monitored using the Liropus 2000 ROV. Litter items were identified in 24 of the 26 dives carried out in the study area, at depths ranging from 140 to 1731 m. Relative abundance of litter objects by type, size and apparent weight, and distribution of litter in relation to depth and canyon environments (i.e. floor and flanks) were analysed. Plastics are the dominant litter component (72%), followed by lost fishing gear, disregarding their composition (17%), and metal objects (8%). Most of the observed litter seems to be land-sourced. It reaches the ocean through wind transport, river discharge and after direct dumping along the coastline. While coastal towns and industrial areas represent a permanent source of litter, tourism and associated activities relevantly increase litter production during summer months ready to be transported to the deep sea by extreme events. After being lost, fishing gear such as nets and long-lines has the potential of being harmful for marine life (e.g. by ghost fishing), at least for some time, but also provides shelter and a substrate on which some species like cold-water corals are capable to settle and grow. La Fonera and Cap de Creus canyons show the highest mean concentrations of litter ever seen on the deep-sea floor, with 15,057 and 8090 items km-2, respectively, and for a single dive litter observed reached 167,540 items km-2. While most of the largest concentrations were found on the canyon floors at

  20. Comparative analysis of triangular rigid zone models in the mechanical study of drawing processes by upper bound; Analisis compartivo de modelos de bloques rigidos triangulares en el estudio mecanico de procesos de estirado por limite superior

    Energy Technology Data Exchange (ETDEWEB)

    Rubio, E. M.; Domingo, R.; Gonzalez, C.; Sanz, A.

    2004-07-01

    To study the optimised geometrical configuration to carry out mechanical drawing of plates is the main objective of this paper. To accomplish this objective, a comparative analysis of some suitable geometrical and kinematic configurations of the material located in the deformation zone has been made. Concretely, several triangular rigid zone models have been chosen, for each one, the overall energy involved in the process have been calculated and an estimation of its different components has been made. The calculation of the energy has been achieved applying the Upper Bound Theorem under plane strain and partial friction conditions. In addition, the range of use for the selected configurations has been established. (Author) 19 refs.

  1. A Critical Discussion of Deep and Surface Processing: What It Means, How It Is Measured, the Role of Context, and Model Specification

    Science.gov (United States)

    Dinsmore, Daniel L.; Alexander, Patricia A.

    2012-01-01

    The prevailing assumption by some that deep processing promotes stronger learning outcomes while surface processing promotes weaker learning outcomes has been called into question by the inconsistency and ambiguity of results in investigations of the relation between levels of processing and performance. The purpose of this literature review is to…

  2. Search for QCD-instanton-induced processes in deep inelastic scattering at HERA

    International Nuclear Information System (INIS)

    Sievers, M.

    2000-07-01

    A limit on the QCD instanton induced cross section has been determined using the data recorded by the ZEUS detector during the year 1997, with a total integrated luminosity of 26 pb -1 . Deep inelastic scattering events were selected, requiring Q 2 > 75 GeV 2 and x > 10 -3 . Cuts to enrich the instanton fraction (final cuts) have been devised: They are the jet transverse momentum, the reconstructed Q '2 , the transverse energy, the mass and the multiplicity of the instanton candidate. The best strategy to determine a limit on fraction of the instanton candidates among the events after the final cuts has turned out to be a fit to the sphericity distributions. The upper limit at 95% confidence level of the fraction of instanton events in the DIS sample, including systematic errors, is f lim,Hrw = 12% for the Herwig Monte Carlo program. Using the Ariadne Monte Carlo program yields a limit of f lim,Ari = 8.2%. These limits have to be compared to the value predicted by theory (QCDINS 1.6) of: f = 6.2% A second, independent, method relying on the best strategy of cuts was not as sensitive and gave weaker limits. (orig.)

  3. Genomic region operation kit for flexible processing of deep sequencing data.

    Science.gov (United States)

    Ovaska, Kristian; Lyly, Lauri; Sahu, Biswajyoti; Jänne, Olli A; Hautaniemi, Sampsa

    2013-01-01

    Computational analysis of data produced in deep sequencing (DS) experiments is challenging due to large data volumes and requirements for flexible analysis approaches. Here, we present a mathematical formalism based on set algebra for frequently performed operations in DS data analysis to facilitate translation of biomedical research questions to language amenable for computational analysis. With the help of this formalism, we implemented the Genomic Region Operation Kit (GROK), which supports various DS-related operations such as preprocessing, filtering, file conversion, and sample comparison. GROK provides high-level interfaces for R, Python, Lua, and command line, as well as an extension C++ API. It supports major genomic file formats and allows storing custom genomic regions in efficient data structures such as red-black trees and SQL databases. To demonstrate the utility of GROK, we have characterized the roles of two major transcription factors (TFs) in prostate cancer using data from 10 DS experiments. GROK is freely available with a user guide from >http://csbi.ltdk.helsinki.fi/grok/.

  4. Deep brain stimulation of the subthalamic nucleus modulates reward processing and action selection in Parkinson patients.

    Science.gov (United States)

    Wagenbreth, Caroline; Zaehle, Tino; Galazky, Imke; Voges, Jürgen; Guitart-Masip, Marc; Heinze, Hans-Jochen; Düzel, Emrah

    2015-06-01

    Deep brain stimulation (DBS) of the subthalamic nucleus (STN) is an effective treatment for motor impairments in Parkinson's disease (PD) but its effect on the motivational regulation of action control is still not fully understood. We investigated whether DBS of the STN influences the ability of PD patients to act for anticipated reward or loss, or whether DBS improves action execution independent of motivational valence. 16 PD patients (12 male, mean age = 58.5 ± 10.17 years) treated with bilateral STN-DBS and an age- and gender-matched group of healthy controls (HC) performed a go/no-go task whose contingencies explicitly decouple valence and action. Patients were tested with (ON) and without (OFF) active STN stimulation. For HC, there was a benefit in performing rewarded actions when compared to actions that avoided punishment. PD patients showed such a benefit reliably only when STN stimulation was ON. In fact, the relative behavioral benefit for go for reward over go to avoid losing was stronger in the PD patients under DBS ON than in HC. In PD patients, rather than generally improving motor functions independent of motivational valence, modulation of the STN by DBS improves action execution specifically when rewards are anticipated. Thus, STN-DBS establishes a reliable congruency between action and reward ("Pavlovian congruency") and remarkably enhances it over the level observed in HC.

  5. Particle mixing processes of Chernobyl fallout in deep Norwegian Sea sediments: Evidence for seasonal effects

    Science.gov (United States)

    Balzer, W.

    1996-09-01

    A 1430 m deep station in the Norwegian Sea (Voering Plateau) was occupied five times between May 1986 and February 1987 to investigate the seasonal variation in sediment mixing rates. Cherbnbyl-derived radiocesium, identified by its high proportion of short-lived 134Cs, was used as a tracer for mixing. Most of the nuclide input arrived at the sediment within a narrow time span in June/early July during the beginning of the seasonal biogenic sedimentation pulse. Measured 137Cs profiles in the sediment over time were compared with modelled distributions calculated with a finite difference scheme. The input function of radiocesium to the sea floor was evaluated from the increase of the total inventory with time. Time-invariant mixing coefficients did not provide reasonable fits to either summer or winter distributions. The best fit was obtained with a rate of mixing proportional to the radiocesium input flux, with an average enhancement factor of 6.6 during the two summer months. It appears that the benthic macrofauna are more active during the food supply season and rapidly ingest/bury freshly sedimented materials.

  6. Implicit and explicit processing in deep dyslexia: Semantic blocking as a test for failure of inhibition in the phonological output lexicon.

    Science.gov (United States)

    Colangelo, Annette; Buchanan, Lori

    2006-12-01

    The failure of inhibition hypothesis posits a theoretical distinction between implicit and explicit access in deep dyslexia. Specifically, the effects of failure of inhibition are assumed only in conditions that have an explicit selection requirement in the context of production (i.e., aloud reading). In contrast, the failure of inhibition hypothesis proposes that implicit processing and explicit access to semantic information without production demands are intact in deep dyslexia. Evidence for intact implicit and explicit access requires that performance in deep dyslexia parallels that observed in neurologically intact participants on tasks based on implicit and explicit processes. In other words, deep dyslexics should produce normal effects in conditions with implicit task demands (i.e., lexical decision) and on tasks based on explicit access without production (i.e., forced choice semantic decisions) because failure of inhibition does not impact the availability of lexical information, only explicit retrieval in the context of production. This research examined the distinction between implicit and explicit processes in deep dyslexia using semantic blocking in lexical decision and forced choice semantic decisions as a test for the failure of inhibition hypothesis. The results of the semantic blocking paradigm support the distinction between implicit and explicit processing and provide evidence for failure of inhibition as an explanation for semantic errors in deep dyslexia.

  7. Emotional words can be embodied or disembodied: the role of superficial vs. deep types of processing

    OpenAIRE

    Abbassi, Ensie; Blanchette, Isabelle; Ansaldo, Ana I.; Ghassemzadeh, Habib; Joanette, Yves

    2015-01-01

    Emotional words are processed rapidly and automatically in the left hemisphere (LH) and slowly, with the involvement of attention, in the right hemisphere (RH). This review aims to find the reason for this difference and suggests that emotional words can be processed superficially or deeply due to the involvement of the linguistic and imagery systems, respectively. During superficial processing, emotional words likely make connections only with semantically associated words in the LH. This pa...

  8. Site selection and characterization processes for deep geologic disposal of high level nuclear waste

    International Nuclear Information System (INIS)

    Costin, L.S.

    1997-10-01

    In this paper, the major elements of the site selection and characterization processes used in the US high level waste program are discussed. While much of the evolution of the site selection and characterization processes have been driven by the unique nature of the US program, these processes, which are well defined and documented, could be used as an initial basis for developing site screening, selection, and characterization programs in other countries. Thus, this paper focuses more on the process elements than the specific details of the US program

  9. Site selection and characterization processes for deep geologic disposal of high level nuclear waste

    International Nuclear Information System (INIS)

    Costin, L.S.

    1997-01-01

    In this paper, the major elements of the site selection and characterization processes used in the U. S. high level waste program are discussed. While much of the evolution of the site selection and characterization processes have been driven by the unique nature of the U. S. program, these processes, which are well-defined and documented, could be used as an initial basis for developing site screening, selection, and characterization programs in other countries. Thus, this paper focuses more on the process elements than the specific details of the U. S. program. (author). 3 refs., 2 tabs., 5 figs

  10. Site selection and characterization processes for deep geologic disposal of high level nuclear waste

    Energy Technology Data Exchange (ETDEWEB)

    Costin, L.S. [Sandia National Labs., Albuquerque, NM (United States)

    1997-12-31

    In this paper, the major elements of the site selection and characterization processes used in the U. S. high level waste program are discussed. While much of the evolution of the site selection and characterization processes have been driven by the unique nature of the U. S. program, these processes, which are well-defined and documented, could be used as an initial basis for developing site screening, selection, and characterization programs in other countries. Thus, this paper focuses more on the process elements than the specific details of the U. S. program. (author). 3 refs., 2 tabs., 5 figs.

  11. Process for selecting a site for Canada's deep geological repository for used nuclear fuel

    International Nuclear Information System (INIS)

    Facella, J.; Ben Belfadhel, M.; Patton, P.

    2012-01-01

    'Full Text:' The Nuclear Waste Management Organization (NWMO) is responsible for implementing Adaptive Phased Management, the approach selected by the Government of Canada for long-term management of used nuclear fuel waste generated by Canadian nuclear reactors. The ultimate objective of Adaptive Phased Management is the centralized containment and isolation of Canada's used nuclear fuel in a Deep Geological Repository in a suitable crystalline or sedimentary rock formation at a depth of about 500m. The repository will consist of a series of access and service shafts and a series of tunnels leading to placement rooms where used fuel will be placed and sealed in competent rock using a multi-barrier system which includes long lived specially designed containers, sealing materials such as bentonite and the rock itself. The used fuel will be monitored throughout all phases of implementation and will also remain retrievable for an extended period of time. In May 2010, the NWMO published the site selection process that serves as the road map to decision-making on the location for the deep geological repository. NWMO initiated the process with a first stage that invites communities to learn more about the project and the site selection process. NWMO is actively building awareness of the project and, on request of communities, is delivering briefings, supporting community capacity building and undertaking screenings of site suitability. This panel presentation provides a brief description of: Adaptive Phased Management including the deep geological repository which is its ultimate goal, and the design of the site selection process, and importantly the approach to assessing the suitability of sites from both a social and technical perspective. The panel presentation will be conducted in three parts: site selection process and engagement, Aboriginal engagement and Technical evaluations, followed by a discussion. The presentation will outline how NWMO sought

  12. Effects of Coherence and Relevance on Shallow and Deep Text Processing.

    Science.gov (United States)

    Lehman, Stephen; Schraw, Gregory

    2002-01-01

    Examines the effects of coherence and relevance on shallow and deeper text processing, testing the hypothesis that enhancing the relevance of text segments compensates for breaks in local and global coherence. Results reveal that breaks in local coherence had no effect on any outcome measures, whereas relevance enhanced deeper processing.…

  13. Deep Sequence Analysis of AgoshRNA Processing Reveals 3' A Addition and Trimming

    NARCIS (Netherlands)

    Harwig, Alex; Herrera-Carrillo, Elena; Jongejan, Aldo; van Kampen, Antonius Hubertus; Berkhout, Ben

    2015-01-01

    The RNA interference (RNAi) pathway, in which microprocessor and Dicer collaborate to process microRNAs (miRNA), was recently expanded by the description of alternative processing routes. In one of these noncanonical pathways, Dicer action is replaced by the Argonaute2 (Ago2) slicer function. It was

  14. Natural analogues: studies of geological processes relevant to radioactive waste disposal in deep geological repositories

    Energy Technology Data Exchange (ETDEWEB)

    Russel, A.W. [Bedrock Geosciences, Auenstein (Switzerland); Reijonen, H.M. [Saanio and Rickkola Oy, Helsinki (Finland); McKinley, I.G. [MCM Consulting, Baden-Daettwil (Switzerland)

    2015-06-15

    The geological disposal of radioactive wastes is generally accepted to be the most practicable approach to handling the waste inventory built up from over 70 years accumulation of power production, research-medical-industrial and military wastes. Here, a brief overview of the approach to geological disposal is presented along with some information on repository design and the assessment of repository post-closure safety. One of the significant challenges for repository safety assessment is how to extrapolate the likely long-term (i.e. ten thousand to a million years) behaviour of the repository from the necessarily short term data from analytical laboratories and underground rock laboratories currently available. One approach, common to all fields of the geosciences, but also in such diverse fields as philosophy, biology, linguistics, law, etc., is to utilise the analogue argumentation methodology. For the specific case of radioactive waste management, the term 'natural analogue' has taken on a particular meaning associated with providing supporting arguments for a repository safety assessment. This approach is discussed here with a brief overview of how the study of natural (and, in particular, geological) systems can provide supporting information on the likely long-term evolution of a deep geological waste repository. The overall approach is discussed and some relevant examples are presented, including the use of uranium ore bodies to assess waste form stability, the investigation of native metals to define the longevity of waste containers and how natural clays can provide information on the stability of waste tunnel backfill material. (authors)

  15. Natural analogues: studies of geological processes relevant to radioactive waste disposal in deep geological repositories

    International Nuclear Information System (INIS)

    Russel, A.W.; Reijonen, H.M.; McKinley, I.G.

    2015-01-01

    The geological disposal of radioactive wastes is generally accepted to be the most practicable approach to handling the waste inventory built up from over 70 years accumulation of power production, research-medical-industrial and military wastes. Here, a brief overview of the approach to geological disposal is presented along with some information on repository design and the assessment of repository post-closure safety. One of the significant challenges for repository safety assessment is how to extrapolate the likely long-term (i.e. ten thousand to a million years) behaviour of the repository from the necessarily short term data from analytical laboratories and underground rock laboratories currently available. One approach, common to all fields of the geosciences, but also in such diverse fields as philosophy, biology, linguistics, law, etc., is to utilise the analogue argumentation methodology. For the specific case of radioactive waste management, the term 'natural analogue' has taken on a particular meaning associated with providing supporting arguments for a repository safety assessment. This approach is discussed here with a brief overview of how the study of natural (and, in particular, geological) systems can provide supporting information on the likely long-term evolution of a deep geological waste repository. The overall approach is discussed and some relevant examples are presented, including the use of uranium ore bodies to assess waste form stability, the investigation of native metals to define the longevity of waste containers and how natural clays can provide information on the stability of waste tunnel backfill material. (authors)

  16. Optimisation of tungsten ore processing through a deep mineralogical characterisation and the study of the crushing process

    OpenAIRE

    Bascompte Vaquero, Jordi

    2017-01-01

    The unstoppable increasing global demand for metals calls for an urgent development of more efficient extraction and processing methods in the mining industry. Comminution is responsible for nearly half of the energy consumption of the entire mining process, and in the majority of the cases it is far from being optimised. Inside comminution, grinding is widely known for being more inefficient than crushing, however, it is needed to reach liberation at an ultrafine particle size. ...

  17. The TOPOMOD-ITN project: unravel the origin of Earth's topography from modelling deep-surface processes

    Science.gov (United States)

    Faccenna, C.; Funiciello, F.

    2012-04-01

    EC-Marie Curie Initial Training Networks (ITN) projects aim to improve the career perspectives of young generations of researchers. Institutions from both academic and industry sectors form a collaborative network to recruit research fellows and provide them with opportunities to undertake research in the context of a joint research training program. In this frame, TOPOMOD - one of the training activities of EPOS, the new-born European Research Infrastructure for Geosciences - is a funded ITN project designed to investigate and model how surface processes interact with crustal tectonics and mantle convection to originate and develop topography of the continents over a wide range of spatial and temporal scales. The multi-disciplinary approach combines geophysics, geochemistry, tectonics and structural geology with advanced geodynamic numerical/analog modelling. TOPOMOD involves 8 European research teams internationally recognized for their excellence in complementary fields of Earth Sciences (Roma TRE, Utrecht, GFZ, ETH, Cambridge, Durham, Rennes, Barcelona), to which are associated 5 research institutions (CNR-Italy, Univ. Parma, Univ. Lausanne, Univ. Montpellier, Univ. Mainz) , 3 high-technology enterprises (Malvern Instruments, TNO, G.O. Logical Consulting) and 1 large multinational oil and gas company (ENI). This unique network places emphasis in experience-based training increasing the impact and international visibility of European research in modeling. Long-term collaboration and synergy are established among the overmentioned research teams through 15 cross-disciplinary research projects that combine case studies in well-chosen target areas from the Mediterranean, the Middle and Far East, west Africa, and South America, with new developments in structural geology, geomorphology, seismology, geochemistry, InSAR, laboratory and numerical modelling of geological processes from the deep mantle to the surface. These multidisciplinary projects altogether aim to

  18. Impact of manual preference on directionality in children's drawings.

    Science.gov (United States)

    Picard, Delphine

    2011-01-01

    The effects of handedness on directionality in drawing are already well documented in the literature, at least as far as adults are concerned. The present study investigates the impact of manual preference on directionality as seen in the drawing product and drawing process, from a developmental point of view. A total of 120 children aged 5 to 9, both right and left-handed drawers, volunteered for the study. Children were asked to draw twice from memory a set of six common objects. Results indicate that directionality in drawing product varies significantly according to manual preference in the 9-year-old children, but not in the younger age groups. The concomitant increase between 7 and 9 years of age in the use of preferred stroke directions and the impact of manual preference in the drawing process suggests that biomechanical factors might play an important role in behavioural asymmetries in drawing.

  19. Redox processes in the safety case of deep geological repositories of radioactive wastes. Contribution of the European RECOSY Collaborative Project

    International Nuclear Information System (INIS)

    Duro, L.; Bruno, J.; Grivé, M.; Montoya, V.; Kienzler, B.; Altmaier, M.; Buckau, G.

    2014-01-01

    Highlights: • The RECOSY project produced results relevant for the Safety Case of nuclear disposal. • We classify the safety related features where RECOSY has contributed. • Redox processes effect the retention of radionuclides in all repository subsystems. - Abstract: Redox processes influence key geochemical characteristics controlling radionuclide behaviour in the near and far field of a nuclear waste repository. A sound understanding of redox related processes is therefore of high importance for developing a Safety Case, the collection of scientific, technical, administrative and managerial arguments and evidence in support of the safety of a disposal facility. This manuscript presents the contribution of the specific research on redox processes achieved within the EURATOM Collaborative Project RECOSY (REdox phenomena COntrolling SYstems) to the Safety Case of nuclear waste disposal facilities. Main objectives of RECOSY were related to the improved understanding of redox phenomena controlling the long-term release or retention of radionuclides in nuclear waste disposal and providing tools to apply the results to Performance Assessment and the Safety Case. The research developed during the project covered aspects of the near-field and the far-field aspects of the repository, including studies relevant for the rock formations considered in Europe as suitable for hosting an underground repository for radioactive wastes. It is the intention of this paper to highlight in which way the results obtained from RECOSY can feed the scientific process understanding needed for the stepwise development of the Safety Case associated with deep geological disposal of radioactive wastes

  20. SHARAKU: an algorithm for aligning and clustering read mapping profiles of deep sequencing in non-coding RNA processing.

    Science.gov (United States)

    Tsuchiya, Mariko; Amano, Kojiro; Abe, Masaya; Seki, Misato; Hase, Sumitaka; Sato, Kengo; Sakakibara, Yasubumi

    2016-06-15

    Deep sequencing of the transcripts of regulatory non-coding RNA generates footprints of post-transcriptional processes. After obtaining sequence reads, the short reads are mapped to a reference genome, and specific mapping patterns can be detected called read mapping profiles, which are distinct from random non-functional degradation patterns. These patterns reflect the maturation processes that lead to the production of shorter RNA sequences. Recent next-generation sequencing studies have revealed not only the typical maturation process of miRNAs but also the various processing mechanisms of small RNAs derived from tRNAs and snoRNAs. We developed an algorithm termed SHARAKU to align two read mapping profiles of next-generation sequencing outputs for non-coding RNAs. In contrast with previous work, SHARAKU incorporates the primary and secondary sequence structures into an alignment of read mapping profiles to allow for the detection of common processing patterns. Using a benchmark simulated dataset, SHARAKU exhibited superior performance to previous methods for correctly clustering the read mapping profiles with respect to 5'-end processing and 3'-end processing from degradation patterns and in detecting similar processing patterns in deriving the shorter RNAs. Further, using experimental data of small RNA sequencing for the common marmoset brain, SHARAKU succeeded in identifying the significant clusters of read mapping profiles for similar processing patterns of small derived RNA families expressed in the brain. The source code of our program SHARAKU is available at http://www.dna.bio.keio.ac.jp/sharaku/, and the simulated dataset used in this work is available at the same link. Accession code: The sequence data from the whole RNA transcripts in the hippocampus of the left brain used in this work is available from the DNA DataBank of Japan (DDBJ) Sequence Read Archive (DRA) under the accession number DRA004502. yasu@bio.keio.ac.jp Supplementary data are available

  1. Multi-Step Deep Reactive Ion Etching Fabrication Process for Silicon-Based Terahertz Components

    Science.gov (United States)

    Jung-Kubiak, Cecile (Inventor); Reck, Theodore (Inventor); Chattopadhyay, Goutam (Inventor); Perez, Jose Vicente Siles (Inventor); Lin, Robert H. (Inventor); Mehdi, Imran (Inventor); Lee, Choonsup (Inventor); Cooper, Ken B. (Inventor); Peralta, Alejandro (Inventor)

    2016-01-01

    A multi-step silicon etching process has been developed to fabricate silicon-based terahertz (THz) waveguide components. This technique provides precise dimensional control across multiple etch depths with batch processing capabilities. Nonlinear and passive components such as mixers and multipliers waveguides, hybrids, OMTs and twists have been fabricated and integrated into a small silicon package. This fabrication technique enables a wafer-stacking architecture to provide ultra-compact multi-pixel receiver front-ends in the THz range.

  2. Revealing stable processing products from ribosome-associated small RNAs by deep-sequencing data analysis.

    Science.gov (United States)

    Zywicki, Marek; Bakowska-Zywicka, Kamilla; Polacek, Norbert

    2012-05-01

    The exploration of the non-protein-coding RNA (ncRNA) transcriptome is currently focused on profiling of microRNA expression and detection of novel ncRNA transcription units. However, recent studies suggest that RNA processing can be a multi-layer process leading to the generation of ncRNAs of diverse functions from a single primary transcript. Up to date no methodology has been presented to distinguish stable functional RNA species from rapidly degraded side products of nucleases. Thus the correct assessment of widespread RNA processing events is one of the major obstacles in transcriptome research. Here, we present a novel automated computational pipeline, named APART, providing a complete workflow for the reliable detection of RNA processing products from next-generation-sequencing data. The major features include efficient handling of non-unique reads, detection of novel stable ncRNA transcripts and processing products and annotation of known transcripts based on multiple sources of information. To disclose the potential of APART, we have analyzed a cDNA library derived from small ribosome-associated RNAs in Saccharomyces cerevisiae. By employing the APART pipeline, we were able to detect and confirm by independent experimental methods multiple novel stable RNA molecules differentially processed from well known ncRNAs, like rRNAs, tRNAs or snoRNAs, in a stress-dependent manner.

  3. Cosmic Infrared Background Fluctuations in Deep Spitzer Infrared Array Camera Images: Data Processing and Analysis

    Science.gov (United States)

    Arendt, Richard; Kashlinsky, A.; Moseley, S.; Mather, J.

    2010-01-01

    This paper provides a detailed description of the data reduction and analysis procedures that have been employed in our previous studies of spatial fluctuation of the cosmic infrared background (CIB) using deep Spitzer Infrared Array Camera observations. The self-calibration we apply removes a strong instrumental signal from the fluctuations that would otherwise corrupt the results. The procedures and results for masking bright sources and modeling faint sources down to levels set by the instrumental noise are presented. Various tests are performed to demonstrate that the resulting power spectra of these fields are not dominated by instrumental or procedural effects. These tests indicate that the large-scale ([greater, similar]30') fluctuations that remain in the deepest fields are not directly related to the galaxies that are bright enough to be individually detected. We provide the parameterization of these power spectra in terms of separate instrument noise, shot noise, and power-law components. We discuss the relationship between fluctuations measured at different wavelengths and depths, and the relations between constraints on the mean intensity of the CIB and its fluctuation spectrum. Consistent with growing evidence that the [approx]1-5 [mu]m mean intensity of the CIB may not be as far above the integrated emission of resolved galaxies as has been reported in some analyses of DIRBE and IRTS observations, our measurements of spatial fluctuations of the CIB intensity indicate the mean emission from the objects producing the fluctuations is quite low ([greater, similar]1 nW m-2 sr-1 at 3-5 [mu]m), and thus consistent with current [gamma]-ray absorption constraints. The source of the fluctuations may be high-z Population III objects, or a more local component of very low luminosity objects with clustering properties that differ from the resolved galaxies. Finally, we discuss the prospects of the upcoming space-based surveys to directly measure the epochs

  4. COSMIC INFRARED BACKGROUND FLUCTUATIONS IN DEEP SPITZER INFRARED ARRAY CAMERA IMAGES: DATA PROCESSING AND ANALYSIS

    International Nuclear Information System (INIS)

    Arendt, Richard G.; Kashlinsky, A.; Moseley, S. H.; Mather, J.

    2010-01-01

    This paper provides a detailed description of the data reduction and analysis procedures that have been employed in our previous studies of spatial fluctuation of the cosmic infrared background (CIB) using deep Spitzer Infrared Array Camera observations. The self-calibration we apply removes a strong instrumental signal from the fluctuations that would otherwise corrupt the results. The procedures and results for masking bright sources and modeling faint sources down to levels set by the instrumental noise are presented. Various tests are performed to demonstrate that the resulting power spectra of these fields are not dominated by instrumental or procedural effects. These tests indicate that the large-scale (∼>30') fluctuations that remain in the deepest fields are not directly related to the galaxies that are bright enough to be individually detected. We provide the parameterization of these power spectra in terms of separate instrument noise, shot noise, and power-law components. We discuss the relationship between fluctuations measured at different wavelengths and depths, and the relations between constraints on the mean intensity of the CIB and its fluctuation spectrum. Consistent with growing evidence that the ∼1-5 μm mean intensity of the CIB may not be as far above the integrated emission of resolved galaxies as has been reported in some analyses of DIRBE and IRTS observations, our measurements of spatial fluctuations of the CIB intensity indicate the mean emission from the objects producing the fluctuations is quite low (∼>1 nW m -2 sr -1 at 3-5 μm), and thus consistent with current γ-ray absorption constraints. The source of the fluctuations may be high-z Population III objects, or a more local component of very low luminosity objects with clustering properties that differ from the resolved galaxies. Finally, we discuss the prospects of the upcoming space-based surveys to directly measure the epochs inhabited by the populations producing these

  5. Deep Reactive Ion Etching (DRIE) of High Aspect Ratio SiC Microstructures using a Time-Multiplexed Etch-Passivate Process

    Science.gov (United States)

    Evans, Laura J.; Beheim, Glenn M.

    2006-01-01

    High aspect ratio silicon carbide (SiC) microstructures are needed for microengines and other harsh environment micro-electro-mechanical systems (MEMS). Previously, deep reactive ion etching (DRIE) of low aspect ratio (AR less than or = 1) deep (greater than 100 micron) trenches in SiC has been reported. However, existing DRIE processes for SiC are not well-suited for definition of high aspect ratio features because such simple etch-only processes provide insufficient control over sidewall roughness and slope. Therefore, we have investigated the use of a time-multiplexed etch-passivate (TMEP) process, which alternates etching with polymer passivation of the etch sidewalls. An optimized TMEP process was used to etch high aspect ratio (AR greater than 5) deep (less than 100 micron) trenches in 6H-SiC. Power MEMS structures (micro turbine blades) in 6H-SiC were also fabricated.

  6. Auto Draw from Excel Input Files

    Science.gov (United States)

    Strauss, Karl F.; Goullioud, Renaud; Cox, Brian; Grimes, James M.

    2011-01-01

    The design process often involves the use of Excel files during project development. To facilitate communications of the information in the Excel files, drawings are often generated. During the design process, the Excel files are updated often to reflect new input. The problem is that the drawings often lag the updates, often leading to confusion of the current state of the design. The use of this program allows visualization of complex data in a format that is more easily understandable than pages of numbers. Because the graphical output can be updated automatically, the manual labor of diagram drawing can be eliminated. The more frequent update of system diagrams can reduce confusion and reduce errors and is likely to uncover symmetric problems earlier in the design cycle, thus reducing rework and redesign.

  7. Drawing new territories

    DEFF Research Database (Denmark)

    Pihl, Ole Verner

    2006-01-01

      ABSTRACT: Are we conscious of the tools we use in the reflective evaluation of the sketch process? Is there room enough for the abstract and intuitive sketch process? The possibilities to unfold the intuitive sketch process have been expanded with the new digital tools. The analog sketch and 3D...

  8. Categorization of the processes contributing to ttH(H→bb) using deep neural networks with the CMS experiment

    Energy Technology Data Exchange (ETDEWEB)

    Rath, Yannik; Erdmann, Martin; Fischer, Benjamin; Fischer, Robert; Heidemann, Fabian; Quast, Thorben; Rieger, Marcel [III. Physikalisches Institut A, RWTH Aachen University (Germany)

    2016-07-01

    In ttH(H→bb) analyses, event categorization is introduced to simultaneously constrain signal and background processes. A common procedure is to categorize events according to both their jet and b-tag multiplicities. The separation power of this approach is limited by the b-tagging efficiency. Especially ttH(H→bb) events with their high b-tag multiplicities suffer from migrations to background categories. In this presentation, we explore deep neural networks (DNNs) as a method of categorizing events according to their jet multiplicity and a DNN event class hypothesis. DNNs have the advantage of being able to learn discriminating features from low level variables, e.g. kinematic properties, and are naturally suited for multiclass classification problems. We compare the ttH signal separation achieved with the DNN method with that of a common categorization approach.

  9. Nanodroplet processing platform for deep and quantitative proteome profiling of 10-100 mammalian cells.

    Science.gov (United States)

    Zhu, Ying; Piehowski, Paul D; Zhao, Rui; Chen, Jing; Shen, Yufeng; Moore, Ronald J; Shukla, Anil K; Petyuk, Vladislav A; Campbell-Thompson, Martha; Mathews, Clayton E; Smith, Richard D; Qian, Wei-Jun; Kelly, Ryan T

    2018-02-28

    Nanoscale or single-cell technologies are critical for biomedical applications. However, current mass spectrometry (MS)-based proteomic approaches require samples comprising a minimum of thousands of cells to provide in-depth profiling. Here, we report the development of a nanoPOTS (nanodroplet processing in one pot for trace samples) platform for small cell population proteomics analysis. NanoPOTS enhances the efficiency and recovery of sample processing by downscaling processing volumes to 3000 proteins are consistently identified from as few as 10 cells. Furthermore, we demonstrate quantification of ~2400 proteins from single human pancreatic islet thin sections from type 1 diabetic and control donors, illustrating the application of nanoPOTS for spatially resolved proteome measurements from clinical tissues.

  10. Quark correlation functions in deep-inelastic semi-inclusive processes

    International Nuclear Information System (INIS)

    Levelt, J.; Mulders, P.J.

    1994-01-01

    We investigate one-particle semi-inclusive processes in lepton-hadron scattering. In unpolarized scattering order Q -1 corrections appear only when transverse momenta are detected. We consider the twist-two and -three matrix elements and calculate the semi-inclusive structure functions in terms of quark correlation functions. We find that at the twist-three level not only the standard quark distribution and fragmentation function contribute, but also two new transverse ''profile functions.'' We discuss the gauge invariance of the hadronic tensor at the twist-three level. The results of our approach are used to calculate expressions for some cross sections for semi-inclusive processes

  11. Deeper than skin deep - The effect of botulinum toxin-A on emotion processing.

    Science.gov (United States)

    Baumeister, J-C; Papa, G; Foroni, F

    2016-08-01

    The effect of facial botulinum Toxin-A (BTX) injections on the processing of emotional stimuli was investigated. The hypothesis, that BTX would interfere with processing of slightly emotional stimuli and less with very emotional or neutral stimuli, was largely confirmed. BTX-users rated slightly emotional sentences and facial expressions, but not very emotional or neutral ones, as less emotional after the treatment. Furthermore, they became slower at categorizing slightly emotional facial expressions under time pressure. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Amides with nitrogenous heterocyclic substituent, their manufacturing process and their use to draw out selectively Actinium series (III) and to separate them in particular from Lanthanides (III)

    International Nuclear Information System (INIS)

    Cuillerdier, C.; Musikas, C.

    1993-01-01

    Present invention is concerned with new amides with nitrogenous heterocyclic substituent utilizable to separate trivalent actinium series from trivalent lanthanides. In these molecules, it is possible to obtain particularly covalent liaison which has more affinity with 5f series, that is to say actinium series; included a manufacturing process for these amides with nitrogenous heterocyclic substituent

  13. A Multidimensional Investigation of Deep-Level and Surface-Level Processing

    Science.gov (United States)

    Dinsmore, Daniel L.; Alexander, Patricia A.

    2016-01-01

    This study examines the moderating effects of a situational factor (i.e., text type) and an individual factor (i.e., subject-matter knowledge) on the relation between depth of processing and performance. One-hundred and fifty-one undergraduates completed measures of subject-matter knowledge, read either an expository or persuasive text about the…

  14. Exploring Students' Reflective Thinking Practice, Deep Processing Strategies, Effort, and Achievement Goal Orientations

    Science.gov (United States)

    Phan, Huy Phuong

    2009-01-01

    Recent research indicates that study processing strategies, effort, reflective thinking practice, and achievement goals are important factors contributing to the prediction of students' academic success. Very few studies have combined these theoretical orientations within one conceptual model. This study tested a conceptual model that included, in…

  15. Deep Processing of Long-Distance Dependencies in L2 English: The Case of Anaphora

    Science.gov (United States)

    Wang, Yi-Ting

    2012-01-01

    Since the seminal work of Alan Juffs, second language (L2) sentence processing has become a central research topic in the field of L2 acquisition. Beyond a general hunger for new data offered by new experimental techniques and designs, intellectual concerns with system-wide understanding of first-language (L1)-L2 differences extended to the…

  16. Comparison of the neural basis for imagined writing and drawing.

    Science.gov (United States)

    Harrington, Greg S; Farias, Dana; Davis, Christine H; Buonocore, Michael H

    2007-05-01

    Drawing and writing are complex processes that require the synchronization of cognition, language, and perceptual-motor skills. Drawing and writing have both been utilized in the treatment of aphasia to improve communication. Recent research suggests that the act of drawing an object facilitated naming, whereas writing the word diminished accurate naming in individuals with aphasia. However, the relationship between object drawing and subsequent phonological output is unclear. Although the right hemisphere is characteristically mute, there is evidence from split-brain research that the right hemisphere can integrate pictures and words, likely via a semantic network. We hypothesized that drawing activates right hemispheric and left perilesional regions that are spared in aphasic individuals and may contribute to semantic activation that supports naming. Eleven right-handed subjects participated in a functional MRI (fMRI) experiment involving imagined drawing and writing and 6 of the 11 subjects participated in a second fMRI experiment involving actual writing and drawing. Drawing and writing produced very similar group activation maps including activation bilaterally in the premotor, inferior frontal, posterior inferior temporal, and parietal areas. The comparison of drawing vs. writing revealed significant differences between the conditions in areas of the brain known for language processing. The direct comparison between drawing and writing revealed greater right hemisphere activation for drawing in language areas such as Brodmann area (BA) 46 and BA 37.

  17. Deep architecture neural network-based real-time image processing for image-guided radiotherapy.

    Science.gov (United States)

    Mori, Shinichiro

    2017-08-01

    To develop real-time image processing for image-guided radiotherapy, we evaluated several neural network models for use with different imaging modalities, including X-ray fluoroscopic image denoising. Setup images of prostate cancer patients were acquired with two oblique X-ray fluoroscopic units. Two types of residual network were designed: a convolutional autoencoder (rCAE) and a convolutional neural network (rCNN). We changed the convolutional kernel size and number of convolutional layers for both networks, and the number of pooling and upsampling layers for rCAE. The ground-truth image was applied to the contrast-limited adaptive histogram equalization (CLAHE) method of image processing. Network models were trained to keep the quality of the output image close to that of the ground-truth image from the input image without image processing. For image denoising evaluation, noisy input images were used for the training. More than 6 convolutional layers with convolutional kernels >5×5 improved image quality. However, this did not allow real-time imaging. After applying a pair of pooling and upsampling layers to both networks, rCAEs with >3 convolutions each and rCNNs with >12 convolutions with a pair of pooling and upsampling layers achieved real-time processing at 30 frames per second (fps) with acceptable image quality. Use of our suggested network achieved real-time image processing for contrast enhancement and image denoising by the use of a conventional modern personal computer. Copyright © 2017 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

  18. Probing connections between deep earth and surface processes in a land-locked ocean basin transformed into a giant saline basin : The Mediterranean GOLD project

    NARCIS (Netherlands)

    Rabineau, M.; Cloetingh, S.; Kuroda, J.; Aslanian, D.; Droxler, A.; Gorini, C.; Garcia-Castellanos, D.; Moscariello, A.; Burov, E.; Sierro, F.; Lirer, F.; Roure, F.; Pezard, P. A.; Matenco, L.; Hello, Y.; Mart, Y.; Camerlenghi, A.; Tripati, A.

    During the last decade, the interaction of deep processes in the lithosphere and mantle with surface processes (erosion, climate, sea-level, subsidence, glacio-isostatic readjustment) has been the subject of heated discussion. The use of a multidisciplinary approach linking geology, geophysics,

  19. Drawing expression of autistic child

    OpenAIRE

    SOLDÁTOVÁ, Barbora

    2016-01-01

    The presented thesis deals with drawing of children with autism. It is divided into two parts, the theoretical and the empirical. In the theoretical parts there are four chapters. Three chapters deal with problem of autism spectrum disorders, types of autism, options of diagnostics, frequency and possible causes of autism. The fourth chapter deals with basic information about children's drawing, unique manifestation of the autistic disablement in the children's drawing. In the empirical part ...

  20. DrawFromDrawings: 2D Drawing Assistance via Stroke Interpolation with a Sketch Database.

    Science.gov (United States)

    Matsui, Yusuke; Shiratori, Takaaki; Aizawa, Kiyoharu

    2017-07-01

    We present DrawFromDrawings, an interactive drawing system that provides users with visual feedback for assistance in 2D drawing using a database of sketch images. Following the traditional imitation and emulation training from art education, DrawFromDrawings enables users to retrieve and refer to a sketch image stored in a database and provides them with various novel strokes as suggestive or deformation feedback. Given regions of interest (ROIs) in the user and reference sketches, DrawFromDrawings detects as-long-as-possible (ALAP) stroke segments and the correspondences between user and reference sketches that are the key to computing seamless interpolations. The stroke-level interpolations are parametrized with the user strokes, the reference strokes, and new strokes created by warping the reference strokes based on the user and reference ROI shapes, and the user study indicated that the interpolation could produce various reasonable strokes varying in shapes and complexity. DrawFromDrawings allows users to either replace their strokes with interpolated strokes (deformation feedback) or overlays interpolated strokes onto their strokes (suggestive feedback). The other user studies on the feedback modes indicated that the suggestive feedback enabled drawers to develop and render their ideas using their own stroke style, whereas the deformation feedback enabled them to finish the sketch composition quickly.

  1. Stages of Drawing and Intelligence

    National Research Council Canada - National Science Library

    Kavanagh, Fintan

    1998-01-01

    Children's drawings follow a developmental sequence. Beginning with uncontrolled scribble, children progress to controlled scribble, through basic forms, to increasingly sophisticated modes of representation...

  2. Optimal Monotone Drawings of Trees

    OpenAIRE

    He, Dayu; He, Xin

    2016-01-01

    A monotone drawing of a graph G is a straight-line drawing of G such that, for every pair of vertices u,w in G, there exists abpath P_{uw} in G that is monotone in some direction l_{uw}. (Namely, the order of the orthogonal projections of the vertices of P_{uw} on l_{uw} is the same as the order they appear in P_{uw}.) The problem of finding monotone drawings for trees has been studied in several recent papers. The main focus is to reduce the size of the drawing. Currently, the smallest drawi...

  3. [Teenagers' drawings in transcultural consultations].

    Science.gov (United States)

    Simon, Amalini; Titia Rizzi, Alice

    The place of teenagers' drawings has been studied as part of a transcultural consultation, based on the creativity of the children of migrants. When speaking is difficult, drawings enable teenagers to show another dimension of their internal world. Aravin, a young Tamil boy, who lacked the necessary words, was able to express all the complexity of his thoughts through his drawings, finally being able to formulate in the group the difficult situations which he was drawing. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  4. Shader-Based Wireframe Drawing

    DEFF Research Database (Denmark)

    Bærentzen, Jakob Andreas; Nielsen, Steen Lund; Gjøl, Mikkel

    2008-01-01

    In this paper, we first argue that drawing lines on polygons is harder than it may appear. We then propose two novel and robust techniques for a special case of this problem, namely wireframe drawing. Neither method suffers from the well-known artifacts associated with the standard two pass, offset...... based techniques for wireframe drawing. Both methods draw prefiltered lines and produce high-quality antialiased results without super-sampling. The first method is a single pass technique well suited for convex N-gons for small N (in particular quadrilaterals or triangles). It is demonstrated...

  5. Engineering drawing from the beginning

    CERN Document Server

    Cousins, M F

    1970-01-01

    Engineering Drawing from the Beginning, Volume 2 discusses the methods for communicating technical engineering concepts through illustrations and drawings. This volume covers the more advance techniques in engineering drawing. The coverage of the text includes the helix, which is the path traced by a point moving uniformly around the surface of a right cylinder that is moving axially. The book also covers drawings of solid objects such as prisms, pyramids, and cones, along with hollow objects made from sheet material. In Chapter 5, the text presents the conventional representations of common

  6. An open-loop system design for deep space signal processing applications

    Science.gov (United States)

    Tang, Jifei; Xia, Lanhua; Mahapatra, Rabi

    2018-06-01

    A novel open-loop system design with high performance is proposed for space positioning and navigation signal processing. Divided by functions, the system has four modules, bandwidth selectable data recorder, narrowband signal analyzer, time-delay difference of arrival estimator and ANFIS supplement processor. A hardware-software co-design approach is made to accelerate computing capability and improve system efficiency. Embedded with the proposed signal processing algorithms, the designed system is capable of handling tasks with high accuracy over long period of continuous measurements. The experiment results show the Doppler frequency tracking root mean square error during 3 h observation is 0.0128 Hz, while the TDOA residue analysis in correlation power spectrum is 0.1166 rad.

  7. Nanodroplet processing platform for deep and quantitative proteome profiling of 10–100 mammalian cells

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Ying; Piehowski, Paul D.; Zhao, Rui; Chen, Jing; Shen, Yufeng; Moore, Ronald J.; Shukla, Anil K.; Petyuk, Vladislav A.; Campbell-Thompson, Martha; Mathews, Clayton E.; Smith, Richard D.; Qian, Wei-Jun; Kelly, Ryan T.

    2018-02-28

    Nanoscale or single cell technologies are critical for biomedical applications. However, current mass spectrometry (MS)-based proteomic approaches require samples comprising a minimum of thousands of cells to provide in-depth profiling. Here, we report the development of a nanoPOTS (Nanodroplet Processing in One pot for Trace Samples) platform as a major advance in overall sensitivity. NanoPOTS dramatically enhances the efficiency and recovery of sample processing by downscaling processing volumes to <200 nL to minimize surface losses. When combined with ultrasensitive LC-MS, nanoPOTS allows identification of ~1500 to ~3,000 proteins from ~10 to ~140 cells, respectively. By incorporating the Match Between Runs algorithm of MaxQuant, >3000 proteins were consistently identified from as few as 10 cells. Furthermore, we demonstrate robust quantification of ~2400 proteins from single human pancreatic islet thin sections from type 1 diabetic and control donors, illustrating the application of nanoPOTS for spatially resolved proteome measurements from clinical tissues.

  8. Influence of batch annealing conditions on the mechanical properties of a drawing steel. Influencia de las condiciones de recocido en campaa sobre las propiedades mecanicas de un acero de embuticion

    Energy Technology Data Exchange (ETDEWEB)

    Saura, J.J.; Carcel, A.; Cembrero, J.; Villena, J. (Departamento de Ingenieria Mecanica y de Materiales, ETSI. Industriales Valencia (Spain))

    1994-01-01

    The aim of this work was to establish correlations between annealing conditions and mechanical properties of extra low carbon deep drawing steel sheets. The mechanical properties can be interpreted on the basis of the microstructures obtained and crystallographic textures. The relationship between process parameters allow to select annealing conditions to achieve the required mechanical and metallurgical characteristics. Author (7 refs.)

  9. Investigation of deep inelastic scattering processes involving large p$_{t}$ direct photons in the final state

    CERN Multimedia

    2002-01-01

    This experiment will investigate various aspects of photon-parton scattering and will be performed in the H2 beam of the SPS North Area with high intensity hadron beams up to 350 GeV/c. \\\\\\\\ a) The directly produced photon yield in deep inelastic hadron-hadron collisions. Large p$_{t}$ direct photons from hadronic interactions are presumably a result of a simple annihilation process of quarks and antiquarks or of a QCD-Compton process. The relative contribution of the two processes can be studied by using various incident beam projectiles $\\pi^{+}, \\pi^{-}, p$ and in the future $\\bar{p}$. \\\\\\\\b) The correlations between directly produced photons and their accompanying hadronic jets. We will examine events with a large p$_{t}$ direct photon for away-side jets. If jets are recognised their properties will be investigated. Differences between a gluon and a quark jet may become observable by comparing reactions where valence quark annihilations (away-side jet originates from a gluon) dominate over the QDC-Compton...

  10. Deep Sequencing Insights in Therapeutic shRNA Processing and siRNA Target Cleavage Precision.

    Science.gov (United States)

    Denise, Hubert; Moschos, Sterghios A; Sidders, Benjamin; Burden, Frances; Perkins, Hannah; Carter, Nikki; Stroud, Tim; Kennedy, Michael; Fancy, Sally-Ann; Lapthorn, Cris; Lavender, Helen; Kinloch, Ross; Suhy, David; Corbau, Romu

    2014-02-04

    TT-034 (PF-05095808) is a recombinant adeno-associated virus serotype 8 (AAV8) agent expressing three short hairpin RNA (shRNA) pro-drugs that target the hepatitis C virus (HCV) RNA genome. The cytosolic enzyme Dicer cleaves each shRNA into multiple, potentially active small interfering RNA (siRNA) drugs. Using next-generation sequencing (NGS) to identify and characterize active shRNAs maturation products, we observed that each TT-034-encoded shRNA could be processed into as many as 95 separate siRNA strands. Few of these appeared active as determined by Sanger 5' RNA Ligase-Mediated Rapid Amplification of cDNA Ends (5-RACE) and through synthetic shRNA and siRNA analogue studies. Moreover, NGS scrutiny applied on 5-RACE products (RACE-seq) suggested that synthetic siRNAs could direct cleavage in not one, but up to five separate positions on targeted RNA, in a sequence-dependent manner. These data support an on-target mechanism of action for TT-034 without cytotoxicity and question the accepted precision of substrate processing by the key RNA interference (RNAi) enzymes Dicer and siRNA-induced silencing complex (siRISC).Molecular Therapy-Nucleic Acids (2014) 3, e145; doi:10.1038/mtna.2013.73; published online 4 February 2014.

  11. Distorted spin dependent spectral function of {sup 3}He and semi-inclusive deep inelastic scattering processes

    Energy Technology Data Exchange (ETDEWEB)

    Kaptari, Leonya P. [University of Perugia (Italy); INFN-Perugia (Italy); Thomas Jefferson National Accelerator Facility, Newport News, VA (United States); Joint Inst. for Nuclear Research, Dubna (Russia); Del Dotto, Alessio [University of Rome, Rome (Italy); INFN-Roma (Italy); Pace, Emanuele [University of Rome (Italy); INFN-Tor Vergata (Italy); Salme, Giovanni [INFN-Roma (Italy); Scopetta, Sergio [University of Perugia (Italy); INFN-Perugia (Italy)

    2014-03-01

    The spin dependent spectral function, relevant to describe polarized electron scattering off polarized {sup 3}He, is studied, within the Plane Wave Impulse Approximation and taking into account final state interaction effects (FSI). In particular, the case of semi-inclusive deep inelastic scattering (SiDIS) is considered, evaluating the FSI of the hadronizing quark with the nuclear remnants. It is shown that particular kinematical regions can be selected to minimize the latter effects, so that parton distributions in the neutron can be accessed. On the other side, in the regions where FSI dominates, the considered reactions can elucidate the mechanism of hadronization of quarks during the propagation in the nuclear medium. It is shown that the obtained spin dependent spectral function can be directly applied to investigate the SiDIS reaction e-vector + {sup 3}He-vector to h+X, where the hadron h originates from the current fragmentation. Experiments of this type are being performed at JLab to extract neutron transverse momentum dependent parton distributions. As a case study, a different SiDIS process, with detection of slow (A-1) systems in the final state, is considered in more details, in order to establish when nuclear structure effects and FSI can be distinguished from elementary reactions on quasi-free nucleons. It is argued that, by a proper choice of kinematics, the origin of nuclear effects in polarized DIS phenomena and the details of the interaction between the hadronizing quark and the nuclear medium can be investigated at a level which is not reachable in inclusive deep inelastic scattering.

  12. Deep desulfurization of middle distillates. Process adaptation to oil fractions' compositions

    Energy Technology Data Exchange (ETDEWEB)

    Pedernera, Esteban; Reimert, Rainer; Nguyen, Ngoc Luan; Van Buren, Vincent [Division of Fuel Technology, Universitat Karlsruhe TH, Engler-Bunte-Ring 1, 76131 Karlsruhe (Germany)

    2003-04-30

    The influence of oil fractions' compositions on the conversion of sulfurous components was investigated in a trickle-bed reactor in laboratory scale. A commercially available NiMo/{gamma}-Al{sub 2}O{sub 3} catalyst was used throughout the investigations. Experimental results including sulfur conversion of different oil fractions and residence time distributions under reacting conditions are presented. The hydrogen consumption is ascribed to the conversion of sulfur and of nitrogen, to the hydrogenation of aromatics and to hydrocracking based on a simulation applying ASPEN Plus. Various configurations of the desulfurization process are evaluated but no advantage is found by separate treatment of individual oil fractions. In addition, experiments were carried out to determine liquid distribution and wetting efficiency in a catalyst bed by using magnetic resonance imaging (MRI) technique.

  13. Gas generation in deep radioactive waste repositories: a review of processes, controls and models

    International Nuclear Information System (INIS)

    Jones, M.A.

    1990-10-01

    Gas generation within radioactive waste repositories may produce two general problems: 1) breaching of engineered and natural barriers due to high gas pressures; 2) enhanced radiological risk due to reduced groundwater travel times and/or greater aqueous or gaseous activities reaching the biosphere. As a result of these concerns, HMIP must be aware of the current status of relevant research, together with any associated deficiencies. This report addresses the current status of published research on near-field gas generation from worldwide sources and documents the important gas generating processes, the factors controlling them and models available to simulate them. In the absence of suitable models, outline technical specifications for corrosion and microbial degradation gas generation models are defined and the deficiencies in the current understanding of gas generation are highlighted; a conceptual research programme to correct these deficiencies is presented. (author)

  14. Drawing Myth and History in visual art

    Directory of Open Access Journals (Sweden)

    Jaime de Córdoba

    2009-07-01

    Full Text Available After the famous exhibition “Copier créer” curated by Jean Pierre Cuzin in the “Musée du Louvre” in 1993, the practice of drawing art has acquired a renovated interest. This exhibition revised the theoretical concepts introduced by Bober and others in the second half of the XXth century and increased the value of the contribution of drawing in the study of art history instead of the idea of copying. An important catalog and essay by Haverkamp, Begemann and Login, titled “Creative copies”, appeared in 1988 and contained the best examples of the main collections. The last but not least important consequence was the collaboration between international museums, using their own spaces, with contemporary artists. The hermeneutic drawings and paintings by Markus Lüpertz in the Munich Glyptotheck and the exhibition of Giacometti’s drawings shown in the IVAM in 2000 are two excellent examples of the European relevance in this field. I want to analyze here twenty years of drawing done in different museums and institutions around the world and its close relationship with the process of recovering our historical memory by using visual art.

  15. Drawing of uranium in γ phase

    International Nuclear Information System (INIS)

    Stohr, J.A.

    1955-01-01

    It describes the study of working and drawing of uranium in γ phase. In a first part, the forgeable characteristics of uranium metal in the three different phases (α, β and γ) are compared by using BASTIEN-PORTEVIN method. The different experiments are testing the behaviour metal in each phase under different stresses and a temperature gradient as slow and shock traction, slow and shock compression, resilience, flexibility. Results show that optimum conditions for uranium drawing is uranium in phase γ. In a second part, it described the drawing method and process. The uranium rods obtained by this technique are of very good quality. In addition, the material wear is very low which permits a low production cost. Finally, the uranium rod physical properties are studied. (M.P.)

  16. How to draw a planarization

    NARCIS (Netherlands)

    Bläsius, T.; Radermacher, M.; Rutter, I.; Steffen, B.; Baier, C.; van den Brand, M.; Eder, J.; Hinchey, M.; Margaria, T.

    2017-01-01

    We study the problem of computing straight-line drawings of non-planar graphs with few crossings. We assume that a crossing-minimization algorithm is applied first, yielding a planarization, i.e., a planar graph with a dummy vertex for each crossing, that fixes the topology of the resulting drawing.

  17. Drawing Links within Dental Education

    Science.gov (United States)

    Wright, J.

    2017-01-01

    This study examines results of a practical drawing task given to a cohort of first year dental surgery students at Kings College Dental Institute, London. It compares and relates their success in drilling and removing caries and pulp tissue from a virtual tooth using the hapTEL virtual learning system, with each individuals' drawing skills.…

  18. Drawing subway maps : a survey

    NARCIS (Netherlands)

    Wolff, A.

    2007-01-01

    This paper deals with automating the drawing of subway maps. There are two features of schematic subway maps that make them different from drawings of other networks such as flow charts or organigrams. First, most schematic subway maps use not only horizontal and vertical lines, but also diagonals.

  19. Heated Hydro-Mechanical Deep Drawing of Magnesium Sheet Metal

    Science.gov (United States)

    Kurz, Gerrit

    In order to reduce fuel consumption efforts have been made to decrease the weight of automobile constructions by increasing the use of lightweight materials. In this field of application magnesium alloys are important because of their low density. A promising alternative to large surfaced and thin die casting parts has been found in construction parts that are manufactured by sheet metal forming of magnesium. Magnesium alloys show a limited formability at room temperature. A considerable improvement of formability can be achieved by heating the material. Formability increases above a temperature of approximately T = 225 °C.

  20. Structure analysis of 3104 aluminium alloy applied to deep drawing

    Energy Technology Data Exchange (ETDEWEB)

    Klyszewski, A.; Lech-Grega, M.; Zelechowski, J.; Szymanski, W. [Light Metals Div., Skawina (Poland). Inst. of Non-Ferrous Metals

    2000-07-01

    Optical and electron microscopy observations and X-ray investigations of 3104 aluminium alloy ingots and bands after experimental heat treatment were carried out. The influence of ingots homogenisation temperature and parameters of material heat treatment after hot rolling on structure, texture and earing of band 0.3 mm thick was analysed. (orig.)

  1. Deep drawing simulations of tailored blanks and experimental verification

    NARCIS (Netherlands)

    Meinders, Vincent T.; van den Berg, Albert; Huetink, Han

    2000-01-01

    Tailored Blanks are increasingly used in the automotive industry. A combination of different materials, thickness, and coatings can be welded together to form a blank for stamping car body panels. The main advantage of using Tailored Blanks is to have specific characteristics at particular parts of

  2. I Draw Therefore I Am: Drawing as Visual (Communication Studies

    Directory of Open Access Journals (Sweden)

    Muliyadi Mahamood

    2013-11-01

    Full Text Available This paper sets view to consider the significance of drawings as part of visual communication design. Drawing gives a chance to observe, to muse, to select and develop continuous thinking techniques. It is to present that drawing is not just a cursory to generate ideas, but it has its own energy and philosophy which deserve studying as a domain of art. In recent years, drawing has received attention; there is on the one hand a group of drawing practitioners, and on the other hand a group of drawing researchers. Drawing in design is a medium of visual and spatial thinking. Digging into research actually is a necessity for visual communication studies. It is suggested here three kinds of research approaches: research into art/design; research through art/design; and research for art/design. Indeed, it leads to four axis topics (topoi for design studies: design practice, design product, design discourse, and design meta-discourse. A field of study called ‘visual culture’ which, departed from the study of critical theory and cultural studies which have set out relatively new field of study called ‘visual studies’. Based upon to this perspective, visual (communication studies should be more self-reflexive. The production of visual communication contributes to construct the visual culture in society.

  3. Optimization of Deep Oxidative Desulfurization Process Using Ionic Liquid and Potassium Monopersulfate

    Directory of Open Access Journals (Sweden)

    Yinke Zhang

    2018-01-01

    Full Text Available Response surface methodology (RSM was selected to optimize a desulfurization process with metal based ionic liquids ([Bmim]Cl/CoCl2 and potassium monopersulfate (PMS together to remove benzothiophene (BT from octane (simulating oil. The four experimental conditions of PMS dosage, [Bmim]Cl/CoCl2 dosage, temperature, and reaction time were investigated. The results showed that the quadratic relationship was built up between BT removal and four experimental variables with 0.9898 fitting coefficient. The optimal conditions were 1.6 g (20 wt% PMS solution, 3.2 g [Bmim]Cl/CoCl2, 46°C, and 23 min, which were obtained based on RSM and experimental results. Under the optimal condition, predicted sulfur removal rate and experimental sulfur removal rate were 96.7% and 95.4%, respectively. The sequence of four experimental conditions on desulfurization followed the order temperature > time > [Bmim]Cl/CoCl2 dosage > PMS solution dosage.

  4. Link between concentrations of sediment flux and deep crustal processes beneath the European Alps.

    Science.gov (United States)

    Garefalakis, Philippos; Schlunegger, Fritz

    2018-01-09

    Large sediment fluxes from mountain belts have the potential to cause megafans to prograde into the neighbouring sedimentary basins. These mechanisms have been documented based from numerical modelling and stratigraphic records. However, little attention has been focused on inferring temporal changes in the concentrations of supplied sediment from coarse-grained deposits. Here, we extract changes of this variable in the field from a Late Oligocene, c. 4 km-thick suite of fluvial conglomerates situated in the North Alpine foreland basin, which evolved in response to the tectonic and erosional history of the Alps. We measure a decrease in channel depths from >2 m to 20 cm from the base to the top of the suite. These constraints are used to calculate an increase in fan surface slopes from 1.0° based on the Shields criteria for sediment entrainment. We combine slope and bulk grain size data with the Bagnold equation for sediment transport to infer higher concentrations of the supplied sediment. We use these shifts to propose a change towards faster erosion and a steeper landscape in the Alpine hinterland, driven by mantle-scale processes beneath the Alps.

  5. Long time-series of chemical and isotopic compositions of Vesuvius fumaroles: evidence for deep and shallow processes

    Directory of Open Access Journals (Sweden)

    Berardino Bocchino

    2011-06-01

    Full Text Available Long time-series of chemical and isotopic compositions of Vesuvius fumaroles were acquired in the framework of the volcanic surveillance in the 1998-2010 period. These allow the identification of processes that occur at shallow levels in the hydrothermal system, and variations that are induced by deep changes in volcanic activity. Partial condensation processes of fumarolic water under near-discharge conditions can explain the annual 18O and deuterium variabilities that are observed at Vesuvius fumaroles. Significant variations in the chemical compositions of fumaroles occurred over the 1999-2002 period, which accompanied the seismic crisis of autumn 1999, when Vesuvius was affected by the most energetic earthquakes of its last quiescence period. A continuous increase in the relative concentrations of CO2 and He and a general decrease in the CH4 concentrations are interpreted as the consequence of an increment in the relative amount of magmatic fluids in the hydrothermal system. Gas equilibria support this hypothesis, showing a PCO2 peak that culminated in 2002, increasing from values of ~40 bar in 1998 to ~55-60 bar in 2001-2002. We propose that the seismic crisis of 1999 marked the arrival of the magmatic fluids into the hydrothermal system, which caused the observed geochemical variations that started in 1999 and culminated in 2002.

  6. Temporary dietary iron restriction affects the process of thrombus resolution in a rat model of deep vein thrombosis.

    Directory of Open Access Journals (Sweden)

    Makiko Oboshi

    Full Text Available Deep vein thrombosis (DVT is a major cause of pulmonary thromboembolism and sudden death. Thus, it is important to consider the pathophysiology of DVT. Recently, iron has been reported to be associated with thrombotic diseases. Hence, in this study, we investigate the effects of dietary iron restriction on the process of thrombus resolution in a rat model of DVT.We induced DVT in 8-week-old male Sprague-Dawley rats by performing ligations of their inferior venae cavae. The rats were then given either a normal diet (DVT group or an iron-restricted diet (DVT+IR group. Thrombosed inferior venae cavae were harvested at 5 days after ligation.The iron-restricted diet reduced venous thrombus size compared to the normal diet. Intrathrombotic collagen content was diminished in the DVT+IR group compared to the DVT group. In addition, intrathrombotic gene expression and the activity of matrix metalloproteinase-9 were increased in the DVT+IR group compared to the DVT group. Furthermore, the DVT+IR group had greater intrathrombotic neovascularization as well as higher gene expression levels of urokinase-type plasminogen activator and tissue-type plasminogen activator than the DVT group. The iron-restricted diet decreased intrathrombotic superoxide production compared to the normal diet.These results suggest that dietary iron restriction affects the process of thrombus resolution in DVT.

  7. Temporary dietary iron restriction affects the process of thrombus resolution in a rat model of deep vein thrombosis.

    Science.gov (United States)

    Oboshi, Makiko; Naito, Yoshiro; Sawada, Hisashi; Hirotani, Shinichi; Iwasaku, Toshihiro; Okuhara, Yoshitaka; Morisawa, Daisuke; Eguchi, Akiyo; Nishimura, Koichi; Fujii, Kenichi; Mano, Toshiaki; Ishihara, Masaharu; Masuyama, Tohru

    2015-01-01

    Deep vein thrombosis (DVT) is a major cause of pulmonary thromboembolism and sudden death. Thus, it is important to consider the pathophysiology of DVT. Recently, iron has been reported to be associated with thrombotic diseases. Hence, in this study, we investigate the effects of dietary iron restriction on the process of thrombus resolution in a rat model of DVT. We induced DVT in 8-week-old male Sprague-Dawley rats by performing ligations of their inferior venae cavae. The rats were then given either a normal diet (DVT group) or an iron-restricted diet (DVT+IR group). Thrombosed inferior venae cavae were harvested at 5 days after ligation. The iron-restricted diet reduced venous thrombus size compared to the normal diet. Intrathrombotic collagen content was diminished in the DVT+IR group compared to the DVT group. In addition, intrathrombotic gene expression and the activity of matrix metalloproteinase-9 were increased in the DVT+IR group compared to the DVT group. Furthermore, the DVT+IR group had greater intrathrombotic neovascularization as well as higher gene expression levels of urokinase-type plasminogen activator and tissue-type plasminogen activator than the DVT group. The iron-restricted diet decreased intrathrombotic superoxide production compared to the normal diet. These results suggest that dietary iron restriction affects the process of thrombus resolution in DVT.

  8. Automatical and accurate segmentation of cerebral tissues in fMRI dataset with combination of image processing and deep learning

    Science.gov (United States)

    Kong, Zhenglun; Luo, Junyi; Xu, Shengpu; Li, Ting

    2018-02-01

    Image segmentation plays an important role in medical science. One application is multimodality imaging, especially the fusion of structural imaging with functional imaging, which includes CT, MRI and new types of imaging technology such as optical imaging to obtain functional images. The fusion process require precisely extracted structural information, in order to register the image to it. Here we used image enhancement, morphometry methods to extract the accurate contours of different tissues such as skull, cerebrospinal fluid (CSF), grey matter (GM) and white matter (WM) on 5 fMRI head image datasets. Then we utilized convolutional neural network to realize automatic segmentation of images in deep learning way. Such approach greatly reduced the processing time compared to manual and semi-automatic segmentation and is of great importance in improving speed and accuracy as more and more samples being learned. The contours of the borders of different tissues on all images were accurately extracted and 3D visualized. This can be used in low-level light therapy and optical simulation software such as MCVM. We obtained a precise three-dimensional distribution of brain, which offered doctors and researchers quantitative volume data and detailed morphological characterization for personal precise medicine of Cerebral atrophy/expansion. We hope this technique can bring convenience to visualization medical and personalized medicine.

  9. Method and an apparatus to control the lateral motion of a long metal bar being formed by a mechanical process such as rolling or drawing

    Science.gov (United States)

    Chang, Tzyy-Shuh; Huang, Hsun-Hau; Lin, Chang-Hung

    2007-10-02

    An adjustable guide, includes two or more mechanisms each having a rotatable retaining element containing a retaining groove with a variable radius in its perimeter surface. The grooves form a guidance path to control the lateral, i.e. non-axial, motion of a long bar moving along a longitudinal axis during a production process.The diameter of the guidance path varies according to the variable radii of the grooves. The guidance path increases in size at a predetermined rate, from a point of origin to an end point on the retaining groove. Rotating the retaining elements causes the diameter of the retaining grooves to change so that the size of the guidance path can be changed to match the diameter of the bar being rolled, size of the guidance path can be changed to fit the diameter of a new bar rolled without having to exchange the guide for a different sized guide, reduce fiction between the bar and the guide, a media, such as compressed air, can be injected between the retaining elements via orifices.Each retaining element is attached to a mounting apparatus. The mounting apparatus can be fixed or flexible. The flexible mounting apparatus includes one or more springs and one or more shock absorbers. A force neutral position of the flexible mounting apparatus is designed to be located on the predetermined ideal bar path line. The flexible mounting apparatus dissipates kinetic energy from the bar thereby reducing the bar's lateral motion relative to the ideal bar path line.The damping ratio of the mounting apparatus can be adjustable to alter the product's vibration mode to enable better control of the bar's lateral motion.

  10. Opposite effects of ketamine and deep brain stimulation on rat thalamocortical information processing.

    Science.gov (United States)

    Kulikova, Sofya P; Tolmacheva, Elena A; Anderson, Paul; Gaudias, Julien; Adams, Brendan E; Zheng, Thomas; Pinault, Didier

    2012-11-01

    Sensory and cognitive deficits are common in schizophrenia. They are associated with abnormal brain rhythms, including disturbances in γ frequency (30-80 Hz) oscillations (GFO) in cortex-related networks. However, the underlying anatomofunctional mechanisms remain elusive. Clinical and experimental evidence suggests that these deficits result from a hyporegulation of glutamate N-methyl-D-aspartate receptors. Here we modeled these deficits in rats with ketamine, a non-competitive N-methyl-D-aspartate receptor antagonist and a translational psychotomimetic substance at subanesthetic doses. We tested the hypothesis that ketamine-induced sensory deficits involve an impairment of the ability of the thalamocortical (TC) system to discriminate the relevant information from the baseline activity. Furthermore, we wanted to assess whether ketamine disrupts synaptic plasticity in TC systems. We conducted multisite network recordings in the rat somatosensory TC system, natural stimulation of the vibrissae and high-frequency electrical stimulation (HFS) of the thalamus. A single systemic injection of ketamine increased the amount of baseline GFO, reduced the amplitude of the sensory-evoked TC response and decreased the power of the sensory-evoked GFO. Furthermore, cortical application of ketamine elicited local and distant increases in baseline GFO. The ketamine effects were transient. Unexpectedly, HFS of the TC pathway had opposite actions. In conclusion, ketamine and thalamic HFS have opposite effects on the ability of the somatosensory TC system to discriminate the sensory-evoked response from the baseline GFO during information processing. Investigating the link between the state and function of the TC system may conceptually be a key strategy to design innovative therapies against neuropsychiatric disorders. © 2012 The Authors. European Journal of Neuroscience © 2012 Federation of European Neuroscience Societies and Blackwell Publishing Ltd.

  11. Adolescence and Family in Argentina. 
Deep Changes in the Process of Emancipation

    Directory of Open Access Journals (Sweden)

    Blas Corsaro

    2016-02-01

    Full Text Available It was believed that adolescents delay more and more the emancipation from home and this became an updated topic for the social results that it has today. Our objective is to measure the relationship children- parents to know if, at the end of the century, adolescents consider it part of their process of growth or, as it was before, a necessity to be free from them. Hypothesis: do current adolescents cohabit in a climate that takes them to be less urged to achieve their independence from parents home? Method: free interviews and semi directed ones with standardized protocol. Results: during 1994-1999- two hundred and eighty Argentine (18-20 years, both sexes said to be conformed with the relationship (84% with their mothers and 72% with their fathers, that the family climate was pleasant(85% and that they were respected in their decisions (88% mother and 85% father. They thought in becoming independent (64%, not to get rid of their parents (85% but because they will feel happy (71%,or to make their own experience (65%, to achieve independence (57% or because they felt already mature (52%. Most of them (53% neither cared get rid of their parents nor felt fear doing that (56% and did not feel (85% to be loosing their parents. It was confirmed that there is a delay to live independently. Such a postponement is not only owed to the economic situation, mostly the harmonic family climate predisposes to continue living with parents that embody new paternal models. . Leaving home is associated more to the pleasure of managering the own life than to getting rid of oppresor parents. 

  12. Drawing-to-Learn: A Framework for Using Drawings to Promote Model-Based Reasoning in Biology

    Science.gov (United States)

    Quillin, Kim; Thomas, Stephen

    2015-01-01

    The drawing of visual representations is important for learners and scientists alike, such as the drawing of models to enable visual model-based reasoning. Yet few biology instructors recognize drawing as a teachable science process skill, as reflected by its absence in the Vision and Change report’s Modeling and Simulation core competency. Further, the diffuse research on drawing can be difficult to access, synthesize, and apply to classroom practice. We have created a framework of drawing-to-learn that defines drawing, categorizes the reasons for using drawing in the biology classroom, and outlines a number of interventions that can help instructors create an environment conducive to student drawing in general and visual model-based reasoning in particular. The suggested interventions are organized to address elements of affect, visual literacy, and visual model-based reasoning, with specific examples cited for each. Further, a Blooming tool for drawing exercises is provided, as are suggestions to help instructors address possible barriers to implementing and assessing drawing-to-learn in the classroom. Overall, the goal of the framework is to increase the visibility of drawing as a skill in biology and to promote the research and implementation of best practices. PMID:25713094

  13. SIMULACIÓN EXPERIMENTAL Y NUMÉRICA DE UN PROCESO DE TREFILADO HÚMEDO DE UN ALAMBRE DE ACERO AL CARBONO EXPERIMENTAL AND NUMERICAL SIMULATION OF THE DAMP WIRE DRAWING PROCESS OF A CARBON STEEL

    Directory of Open Access Journals (Sweden)

    Ennio L Rojas

    2008-06-01

    Full Text Available En este trabajo se presenta un análisis experimental y numérico para la descripción del comportamiento mecánico de un alambre de acero al carbono durante un proceso industrial de trefilado húmedo. En primer lugar, se hizo una campaña experimental de mediciones de fuerza de trefilado de las doce reducciones presentes en el proceso. En segundo lugar, se llevaron a cabo ensayos de tracción con objeto de caracterizar el comportamiento mecánico del material en cada etapa de reducción. En estos ensayos se obtuvieron curvas de tensión-deformación que, en conjunto a las respuestas calculadas a partir de la simulación de los ensayos, permitieron derivar la evolución de los parámetros elásticos y plásticos característicos del material a medida que se reduce su diámetro. De dicha evolución se constató el gran endurecimiento que experimenta el material durante el proceso el que, a su vez, condiciona fuertemente su trefilabilidad. Las simulaciones se realizaron por medio de un modelo elastoplástico de grandes deformaciones implementado en un programa de cálculo preexistente, basado en el método de elementos finitos, denominado VULCAN. Luego, los parámetros del material obtenidos en los ensayos de tracción fueron considerados en la simulación del proceso de deformación que ocurre durante el paso del alambre a través de los dados. Los resultados de la simulación se consideran aceptables y representativos del comportamiento del alambre en el proceso.This paper presents an experimental and numerical analysis for the description of the mechanical behaviour of a carbon steel wire during an industrial process of damp drawing. Firstly, an experimental procedure aimed at measuring wire drawing forces in the twelve reductions present in the process was performed. Secondly, tensile tests were carried out in order to characterize the mechanical behavior of the material for each reduction step. The resulting stress-strain curves together with

  14. One step transesterification process of sludge palm oil (SPO) by using deep eutectic solvent (DES) in biodiesel production

    Science.gov (United States)

    Manurung, Renita; Ramadhani, Debbie Aditia; Maisarah, Siti

    2017-06-01

    Biodiesel production by using sludge palm oil (SPO) as raw material is generally synthesized in two step reactions, namely esterification and transesterification, because the free fatty acid (FFA) content of SPO is relatively high. However, the presence of choline chloride (ChCl), glycerol based deep eutectic solvent (DES), in transesterification may produce biodiesel from SPO in just one step. In this study, DES was produced by the mixture of ChCl and glycerol at molar ratio of 1:2 at a temperature of 80°C and stirring speed of 400 rpm for 1 hour. DES was characterized by its density and viscosity. The transesterification process was performed at reaction temperature of 70 °C, ethanol to oil molar with ratio of 9:1, sodium hydroxide as catalyst concentration of 1 % wt, DES as cosolvent with concentration of 0 to 5 % wt, stirring speed of 400 rpm, and one hour reaction time. The obtained biodiesel was then assessed with density, viscosity, and ester content as the parameters. FFA content of SPO as the raw material was 7.5290 %. In this case, DES as cosolvent in one step transesterification process of low feedstock could reduce the side reaction (saponification), decrease the time reaction, decrease the surface tension between ethanol and oil, and increase the mass transfer that simultaneously simplified the purification process and obtained the highest yield. The esters properties met the international standards of ASTM D 6751, with the highest yield obtained was 83.19% with 99.55% of ester content and the ratio of ethanol:oil of 9:1, concentration of DES of 4%, catalyst amount of 1%, temperature of reaction at 70°C and stirring speed of 400 rpm.

  15. Studies in Cup Drawing Behavior of Polymer Laminated Sheet Metal

    Science.gov (United States)

    Elnagmi, M.; Jain, M.; Bruhis, M.; Nielsen, K.

    2011-08-01

    Axisymmetric deep drawing behavior of a polymer laminated sheet metal (PLSM) is investigated using an axisymmetric cup drawing test. PLSMs are of interest as a replacement for painted finishes for automotive applications as they have the potential to achieve good quality long lasting and aesthetically appealing surfaces on stamped parts. However, there is limited understanding of PLSMs in automotive deep drawing situations to produce complex 3-D parts. The tests are carried out using well-controlled, laboratory-based, dual-action, servo-hydraulic forming presses under blank-holder force and punch displacement control conditions. An optical strain mapping system is used to measure the surface strains (and to construct 3D strain maps) from the film side of the deformed samples for a range of forming conditions. Deep drawing characteristics such as punch load versus punch displacement traces, strain distribution along the cup profile, flange wrinkling and fracture characteristics are experimentally assessed for stainless steel-plastic film laminated sheet materials. Also the effect of lamination pressure on wrinkling and delamination is investigated for a decorative pressure sensitive adhesive film affixed to the stainless steel sheet.

  16. Experimental study on titanium wire drawing with ultrasonic vibration.

    Science.gov (United States)

    Liu, Shen; Shan, Xiaobiao; Guo, Kai; Yang, Yuancai; Xie, Tao

    2018-02-01

    Titanium and its alloys have been widely used in aerospace and biomedical industries, however, they are classified as difficult-to-machine materials. In this paper, ultrasonic vibration is imposed on the die to overcome the difficulties during conventional titanium wire drawing processes at the room temperature. Numerical simulations were performed to investigate the variation of axial stress within the contacting region and study the change of the drawing stress with several factors in terms of the longitudinal amplitude and frequency of the applied ultrasonic vibration, the diameter reduction ratio, and the drawing force. An experimental testing equipment was established to measure the drawing torque and rotational velocity of the coiler drum during the wire drawing process. The result indicates the drawing force increases with the growth of the drawing velocity and the reduction ratio, whether with or without vibrations. Application of either form of ultrasonic vibrations contributes to the further decrease of the drawing force, especially the longitudinal vibration with larger amplitude. SEM was employed to detect the surface morphology of the processed wires drawn under the three circumstances. The surface quality of the drawn wires with ultrasonic vibrations was apparently improved compared with those using conventional method. In addition, the longitudinal and torsional composite vibration was more effective for surface quality improvement than pure longitudinal vibration, however, at the cost of weakened drawing force reduction effect. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Artistic drawing as a mnemonic device

    Science.gov (United States)

    Baker Christensen, Leslie

    Despite art-based learning being widely used, existing data are primarily qualitative, and most research has not isolated particular variables such as memory for empirical study. The few experiments that have been conducted demonstrated that drawing improves free recall of unpaired words, and retention improves after lessons integrated with drawing, drama, and narrative exercises. To help fill the gap in the current literature, the present study compared the effectiveness of encoding and the rate of memory decay between a drawing mnemonic and note taking on a paired associates task. Using a within-subjects experimental design, participants were presented with word pairs and asked to complete either a drawing mnemonic (DM) or note taking (NT) to assist memorization. Participants were tested immediately after the word pair presentation and after a 20-minute delay. Results supported the hypothesis that the DM condition would produce superior encoding, as evidenced by greater retention on the immediate test. However, no memory decay was observed in the experiment, and therefore results on the delayed test were inconclusive. In fact, scores for the NT condition improved over time whereas the scores for the DM condition did not, which might imply that note taking results in a different consolidation process than drawing. Findings from this study suggested that arts integration can be an effective method to support memory for learned information. Future studies that examine the effect of rehearsal and the long-term effectiveness of a drawing mnemonic are warranted. This dissertation is available in open access at AURA, http://aura.antioch.edu/ and Ohio Link ETD Center, https://etd.ohiolink.edu/etd.

  18. Decreasing diameter fluctuation of polymer optical fiber with optimized drawing conditions

    Science.gov (United States)

    Çetinkaya, Onur; Wojcik, Grzegorz; Mergo, Pawel

    2018-05-01

    The diameter fluctuations of poly(methyl methacrylate) based polymer optical fibers, during drawing processes, have been comprehensively studied. In this study, several drawing parameters were selected for investigation; such as drawing tensions, preform diameters, preform feeding speeds, and argon flows. Varied drawing tensions were used to draw fibers, while other parameters were maintained at constant. At a later stage in the process, micro-structured polymer optical fibers were drawn under optimized drawing conditions. Fiber diameter deviations were reduced to 2.2%, when a 0.2 N drawing tension was employed during the drawing process. Higher drawing tensions led to higher diameter fluctuations. The Young’s modulus of fibers drawn with different tensions was also measured. Our results showed that fiber elasticity increased as drawing tensions decreased. The inhomogeneity of fibers was also determined by comparing the deviation of Young’s modulus.

  19. Knudsen pump produced via silicon deep RIE, thermal oxidation, and anodic bonding processes for on-chip vacuum pumping

    Science.gov (United States)

    Van Toan, Nguyen; Inomata, Naoki; Trung, Nguyen Huu; Ono, Takahito

    2018-05-01

    This work describes the fabrication and evaluation of the Knudsen pump for on-chip vacuum pumping that works based on the principle of a thermal transpiration. Three AFM (atomic force microscope) cantilevers are integrated into small chambers with a size of 5 mm  ×  3 mm  ×  0.4 mm for the pump’s evaluation. Knudsen pump is fabricated using deep RIE (reactive ion etching), wet thermal oxidation and anodic bonding processes. The fabricated device is evaluated by monitoring the quality (Q) factor of the integrated cantilevers. The Q factor of the cantilever is increased from 300 -1150 in cases without and with a temperature difference approximately 25 °C between the top (the hot side at 40 °C) and bottom (the cold side at 15 °C) sides of the fabricated device, respectively. The evacuated chamber pressure of around 10 kPa is estimated from the Q factor of the integrated cantilevers.

  20. The effect of deep and slow breathing on pain perception, autonomic activity, and mood processing--an experimental study.

    Science.gov (United States)

    Busch, Volker; Magerl, Walter; Kern, Uwe; Haas, Joachim; Hajak, Göran; Eichhammer, Peter

    2012-02-01

    Deep and slow breathing (DSB) techniques, as a component of various relaxation techniques, have been reported as complementary approaches in the treatment of chronic pain syndromes, but the relevance of relaxation for alleviating pain during a breathing intervention was not evaluated so far. In order to disentangle the effects of relaxation and respiration, we investigated two different DSB techniques at the same respiration rates and depths on pain perception, autonomic activity, and mood in 16 healthy subjects. In the attentive DSB intervention, subjects were asked to breathe guided by a respiratory feedback task requiring a high degree of concentration and constant attention. In the relaxing DSB intervention, the subjects relaxed during the breathing training. The skin conductance levels, indicating sympathetic tone, were measured during the breathing maneuvers. Thermal detection and pain thresholds for cold and hot stimuli and profile of mood states were examined before and after the breathing sessions. The mean detection and pain thresholds showed a significant increase resulting from the relaxing DSB, whereas no significant changes of these thresholds were found associated with the attentive DSB. The mean skin conductance levels indicating sympathetic activity decreased significantly during the relaxing DSB intervention but not during the attentive DSB. Both breathing interventions showed similar reductions in negative feelings (tension, anger, and depression). Our results suggest that the way of breathing decisively influences autonomic and pain processing, thereby identifying DSB in concert with relaxation as the essential feature in the modulation of sympathetic arousal and pain perception. Wiley Periodicals, Inc.

  1. Nonstationary plasma-thermo-fluid dynamics and transition in processes of deep penetration laser beam-matter interaction

    Science.gov (United States)

    Golubev, Vladimir S.; Banishev, Alexander F.; Azharonok, V. V.; Zabelin, Alexandre M.

    1994-09-01

    A qualitative analysis of the role of some hydrodynamic flows and instabilities by the process of laser beam-metal sample deep penetration interaction is presented. The forces of vapor pressure, melt surface tension and thermocapillary forces can determined a number of oscillatory and nonstationary phenomena in keyhole and weld pool. Dynamics of keyhole formation in metal plates has been studied under laser beam pulse effect ((lambda) equals 1.06 micrometers ). Velocities of the keyhole bottom motion have been determined at 0.5 X 105 - 106 W/cm2 laser power densities. Oscillatory regime of plate break- down has been found out. Small-dimensional structures with d-(lambda) period was found on the frozen cavity walls, which, in our opinion, can contribute significantly to laser beam absorption. A new form of periodic structure on the frozen pattern being a helix-shaped modulation of the keyhole walls and bottom relief has been revealed. Temperature oscillations related to capillary oscillations in the melt layer were discovered in the cavity. Interaction of the CW CO2 laser beam and the matter by beam penetration into a moving metal sample has been studied. The pulsed and thermodynamic parameters of the surface plasma were investigated by optical and spectroscopic methods. The frequencies of plasma jets pulsations (in 10 - 105 Hz range) are related to possible melt surface instabilities of the keyhole.

  2. Modelling of processes occurring in deep geological repository - development of new modules in the GoldSim environment

    International Nuclear Information System (INIS)

    Vopalka, D.; Lukin, D.; Vokal, A.

    2006-01-01

    Three new modules modelling the processes that occur in a deep geological repository have been prepared in the GoldSim computer code environment (using its Transport Module). These modules help to understand the role of selected parameters in the near-field region of the final repository and to prepare an own complex model of the repository behaviour. The source term module includes radioactive decay and ingrowth in the canister, first order degradation of fuel matrix, solubility limitation of the concentration of the studied nuclides, and diffusive migration through the surrounding bentonite layer controlled by the output boundary condition formulated with respect to the rate of water flow in the rock. The corrosion module describes corrosion of canisters made of carbon steel and transport of corrosion products in the near-field region. This module computes balance equations between dissolving species and species transported by diffusion and/or advection from the surface of a solid material. The diffusion module that includes also non-linear form of the interaction isotherm can be used for an evaluation of small-scale diffusion experiments. (author)

  3. Modelling of processes occurring in deep geological repository - Development of new modules in the GoldSim environment

    Science.gov (United States)

    Vopálka, D.; Lukin, D.; Vokál, A.

    2006-01-01

    Three new modules modelling the processes that occur in a deep geological repository have been prepared in the GoldSim computer code environment (using its Transport Module). These modules help to understand the role of selected parameters in the near-field region of the final repository and to prepare an own complex model of the repository behaviour. The source term module includes radioactive decay and ingrowth in the canister, first order degradation of fuel matrix, solubility limitation of the concentration of the studied nuclides, and diffusive migration through the surrounding bentonite layer controlled by the output boundary condition formulated with respect to the rate of water flow in the rock. The corrosion module describes corrosion of canisters made of carbon steel and transport of corrosion products in the near-field region. This module computes balance equations between dissolving species and species transported by diffusion and/or advection from the surface of a solid material. The diffusion module that includes also non-linear form of the interaction isotherm can be used for an evaluation of small-scale diffusion experiments.

  4. Animated construction of line drawings

    KAUST Repository

    Fu, Hongbo; Zhou, Shizhe; Liu, Ligang; Mitra, Niloy J.

    2011-01-01

    system produces plausible animated constructions of input line drawings, with no or little user intervention. We test our algorithm on a range of input sketches, with varying degree of complexity and structure, and evaluate the results via a user study

  5. HippoDraw and Hippoplotamus

    International Nuclear Information System (INIS)

    Gravina, M.F.; Kunz, P.F.; Pavel, T.J.; Rensing, P.E.

    1992-02-01

    Hippo Draw is a result of research into finding better ways to visualize the kind of statistical data that is so common in high energy physics analyses. In these analyses, frequency distributions are visualized as histograms, contour plots, scatter plots, etc. Traditionally, one used a library of subroutines, called a histogram package, within one's analysis programs to create and display such distributions. HippoDraw is a NeXTstep application for viewing statistical data. It has several unique features which make viewing data distributions highly interactive. It also incorporates simple drawing tools. HippoDraw is written in Objective-C and uses the Hippoplotamus library package which handles the n-tuples and displays. Hippoplotamus is written in ANSI C. 4 refs

  6. Deterritorializing Drawing - transformation/deformation

    DEFF Research Database (Denmark)

    Brabrand, Helle

    2012-01-01

    but also from within by sensations, body ‘images’ are different to all other images. Twisting these body images make a mode of operation of art. The paper will address the above issues discussing modes of operation and appearance of my actual project. Acting in the reality of drawing, the project confront...... the body, situated in real time and depth, with drawing transforming and deforming time and depth....

  7. Simultaneous identification of DNA and RNA viruses present in pig faeces using process-controlled deep sequencing.

    Directory of Open Access Journals (Sweden)

    Jana Sachsenröder

    Full Text Available BACKGROUND: Animal faeces comprise a community of many different microorganisms including bacteria and viruses. Only scarce information is available about the diversity of viruses present in the faeces of pigs. Here we describe a protocol, which was optimized for the purification of the total fraction of viral particles from pig faeces. The genomes of the purified DNA and RNA viruses were simultaneously amplified by PCR and subjected to deep sequencing followed by bioinformatic analyses. The efficiency of the method was monitored using a process control consisting of three bacteriophages (T4, M13 and MS2 with different morphology and genome types. Defined amounts of the bacteriophages were added to the sample and their abundance was assessed by quantitative PCR during the preparation procedure. RESULTS: The procedure was applied to a pooled faecal sample of five pigs. From this sample, 69,613 sequence reads were generated. All of the added bacteriophages were identified by sequence analysis of the reads. In total, 7.7% of the reads showed significant sequence identities with published viral sequences. They mainly originated from bacteriophages (73.9% and mammalian viruses (23.9%; 0.8% of the sequences showed identities to plant viruses. The most abundant detected porcine viruses were kobuvirus, rotavirus C, astrovirus, enterovirus B, sapovirus and picobirnavirus. In addition, sequences with identities to the chimpanzee stool-associated circular ssDNA virus were identified. Whole genome analysis indicates that this virus, tentatively designated as pig stool-associated circular ssDNA virus (PigSCV, represents a novel pig virus. CONCLUSION: The established protocol enables the simultaneous detection of DNA and RNA viruses in pig faeces including the identification of so far unknown viruses. It may be applied in studies investigating aetiology, epidemiology and ecology of diseases. The implemented process control serves as quality control, ensures

  8. Drawing Millions of Spaces

    DEFF Research Database (Denmark)

    Brabrand, Helle

    2017-01-01

    a flat surface in actual space for projection of line-, photo-, and video effects, and then, out of this surface-context, provoke a participator to move and extract different atmospheric perspectives. Presently, the work is presented as a video. In The Art-Architecture Complex Hal Foster criticizes what...... of process - movement - time. Asking very basic architectural questions, his focus is on elevation, on what happens to your body when the elevation is shifting: how do you cut into space, gather the land in a volume, and hold that volume? Serra’s concern is moving body-space experiences: ‘when you face...... a concave shape, the whole breadth of the curvilinear volume opens up in front of you; but once you walk around the edge, it changes to an opaque convexity that reveals itself only through walking – you can’t see the openness of the field or how the volume sucks into it. Just turning the corner opens up...

  9. Sensitivity of Deep Soil Organic Carbon Age to Sorption, Transport and Microbial Interactions - Insights from a Calibrated Process Model

    Science.gov (United States)

    Ahrens, B.; Schrumpf, M.; Reichstein, M.

    2013-12-01

    Subsoil soil organic carbon (SOC) is characterized by conventional radiocarbon ages on the order of centuries to millennia. Most vertically explicit SOC turnover models represent this persistence of deep SOC by one pool that has millennial turnover times. This approach lumps different stabilizing mechanisms such as chemical recalcitrance, sorptive stabilization and energy limitation into a single rate constant. As an alternative, we present a continuous, vertically explicit SOC decomposition model that allows for stabilization via sorption and microbial interactions (COMISSION model). We compare the COMISSION model with the SOC profile of a Haplic Podzol under a Norway spruce forest. In the COMISSION model two pools receive aboveground litter input and vertically distributed root litter input. The readily leachable and soluble fraction of litter input enters a dissolved organic carbon pool (DOC), while the rest enters the residue pool which represents polymeric, non-soluble SOC. The residue pool is depolymerized with extracellular enzymes produced by a microbial pool to enter the DOC pool which represents SOC potentially available for assimilation by microbes. The adsorption/desorption of DOC from/to mineral surfaces controls the availability of carbon in the DOC pool for assimilatory uptake by microbes. The sorption of DOC is modeled with dynamic Langmuir equations. The desorbed part of the DOC pool not only constitutes the substrate for the microbial pool, but is also transported via advection. Interactions of microbes with the residue and DOC pool are modeled with Michaelis-Menten kinetics - this not only allows representing ';priming', but also the retardation of decomposition via energy limitation in the deep soil where substrate is scarce. Further, soil organic matter is recycled within the soil profile through microbial processing - dead microbes either enter the DOC or the residue pool, and thereby also contribute to longer residence times with soil depth

  10. Stimulating Scientific Reasoning with Drawing-Based Modeling

    Science.gov (United States)

    Heijnes, Dewi; van Joolingen, Wouter; Leenaars, Frank

    2018-01-01

    We investigate the way students' reasoning about evolution can be supported by drawing-based modeling. We modified the drawing-based modeling tool SimSketch to allow for modeling evolutionary processes. In three iterations of development and testing, students in lower secondary education worked on creating an evolutionary model. After each…

  11. 37 CFR 1.152 - Design drawings.

    Science.gov (United States)

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Design drawings. 1.152... Design drawings. The design must be represented by a drawing that complies with the requirements of § 1... are not permitted in a design drawing. Photographs and ink drawings are not permitted to be combined...

  12. Radiation dose reduction in digital breast tomosynthesis (DBT) by means of deep-learning-based supervised image processing

    Science.gov (United States)

    Liu, Junchi; Zarshenas, Amin; Qadir, Ammar; Wei, Zheng; Yang, Limin; Fajardo, Laurie; Suzuki, Kenji

    2018-03-01

    To reduce cumulative radiation exposure and lifetime risks for radiation-induced cancer from breast cancer screening, we developed a deep-learning-based supervised image-processing technique called neural network convolution (NNC) for radiation dose reduction in DBT. NNC employed patched-based neural network regression in a convolutional manner to convert lower-dose (LD) to higher-dose (HD) tomosynthesis images. We trained our NNC with quarter-dose (25% of the standard dose: 12 mAs at 32 kVp) raw projection images and corresponding "teaching" higher-dose (HD) images (200% of the standard dose: 99 mAs at 32 kVp) of a breast cadaver phantom acquired with a DBT system (Selenia Dimensions, Hologic, CA). Once trained, NNC no longer requires HD images. It converts new LD images to images that look like HD images; thus the term "virtual" HD (VHD) images. We reconstructed tomosynthesis slices on a research DBT system. To determine a dose reduction rate, we acquired 4 studies of another test phantom at 4 different radiation doses (1.35, 2.7, 4.04, and 5.39 mGy entrance dose). Structural SIMilarity (SSIM) index was used to evaluate the image quality. For testing, we collected half-dose (50% of the standard dose: 32+/-14 mAs at 33+/-5 kVp) and full-dose (standard dose: 68+/-23 mAs at 33+/-5 kvp) images of 10 clinical cases with the DBT system at University of Iowa Hospitals and Clinics. NNC converted half-dose DBT images of 10 clinical cases to VHD DBT images that were equivalent to full dose DBT images. Our cadaver phantom experiment demonstrated 79% dose reduction.

  13. Cutting costs without drawing blood.

    Science.gov (United States)

    Copeland, T

    2000-01-01

    When looking for ways to cut costs, most managers reach for the head-count hatchet, and the markets usually roar with approval. But a company can almost always create far more sustainable value by rigorously evaluating the small-ticket capital items that often get rubber-stamped. Drawing on his experience as a consultant and providing numerous anecdotes, the author contends that those "little" requests often prove to be gold plated or unnecessary. A disciplined evaluation involves asking only eight questions and conducting postmortems--regular audits of units' capital spending. But the payoff is enormous. Because cutting the capital budget increases cash flow, the author argues that a permanent cut of just 15% in the planned level of capital spending could boost some companies' market capitalization by as much as 30%. The first three questions--Is this your investment to make? Does it really have to be new? How are our competitors meeting compliance needs?--are asked of operating managers as they assemble capital project requests. The next three are asked by senior managers of themselves and their colleagues as they examine proposals: Is the left hand duplicating investments made by the right? Are trade-offs between profit and capital spending well understood? Are there signs of budget massage? At the end of the review process, senior managers ask: Are we fully using shared assets? How fine-grained are our capacity measures? The author's suggestions for the postmortem include searching for systematic problems with whole classes of expenditures and making sure audit teams come up with specific recommendations for change.

  14. The neural basis for simulated drawing and the semantic implications.

    Science.gov (United States)

    Harrington, Greg S; Farias, Dana; Davis, Christine H

    2009-03-01

    This functional magnetic resonance imaging (fMRI) study of the mental simulation of drawing (1) investigated the neural substrates of drawing and (2) delineated the semantic aspects of drawing. The goal was to advance our understanding of how drawing a familiar object is linked to lexical semantics and therefore a viable method to use to rehabilitate aphasia. We hypothesized that the semantic aspects of drawing familiar objects compared to drawing non-objects would yield greater activation in the inferior temporal cortex and the inferior frontal cortex of the left hemisphere. To test this hypothesis, eight right-handed subjects performed an fMRI experiment that directly contrasted drawing familiar objects to non-objects using mental imagery. Simulated drawing recruited a large, distributed network of frontal, parietal, and temporal structures. In the contrast comparing drawing familiar objects to non-objects there was stronger activation in the left hemisphere within the inferior temporal, anterior inferior frontal, inferior parietal and superior frontal cortices. The activation within the inferior temporal cortex was associated with visual semantic processing and semantic mediated naming. We suggest that the anterior inferior frontal activation is linked to the inferior temporal cortex and is involved in the selection of specific semantic features of the object as well as retrieval of information regarding the perceptual aspects of the object.

  15. Drawing Disorders in Alzheimer's Disease and Other Forms of Dementia.

    Science.gov (United States)

    Trojano, Luigi; Gainotti, Guido

    2016-04-21

    Drawing is a multicomponential process that can be impaired by many kinds of brain lesions. Drawing disorders are very common in Alzheimer's disease and other forms of dementia, and can provide clinical information for the distinction of the different dementing diseases. In our review we started from an overview of the neural and cognitive bases of drawing, and from a recollection of the drawing tasks more frequently used for assessing individuals with dementia. Then, we analyzed drawing disorders in dementia, paying special attention to those observed in Alzheimer's disease, from the prodromal stages of the amnesic mild cognitive impairment to the stages of full-blown dementia, both in the sporadic forms with late onset in the entorhino-hippocampal structures and in those with early onset in the posterior neocortical structures. We reviewed the drawing features that could differentiate Alzheimer's disease from vascular dementia and from the most frequent forms of degenerative dementia, namely frontotemporal dementia and Lewy body disease. Finally, we examined some peculiar aspects of drawing disorders in dementia, such as perseverations, rotations, and closing-in. We argue that a careful analysis of drawing errors helps to differentiate the different forms of dementia more than overall accuracy in drawing.

  16. A qualitative evaluation of long-term processes governing the behaviour of uranium mill tailings placed in deep lakes

    International Nuclear Information System (INIS)

    McKee, Paul; Snodgrass, William; Lush, D.L.; Ross, P.

    1982-03-01

    The emplacement of uranim mill tailings in deep lakes may provide an acceptable method of tailings disposal at certain sites in Canada. Disposal in a depositional environment typical of deep lakes appears to offer greater prospects for long-term stability than present methods of land-based management. From the regulatory point of view, it is necessary to know which factors should be taken into account in assessing the acceptability of such an approach. This report examines the environmental variables governing the behaviour of radionuclides and trace elements in the groundwater systems, lake water, and finally in the biosphere over the short and long-term. Physical, chemical and biological factors are each considered. Conclusions are presented in terms of points for and against disposal in deep lakes

  17. A qualitative evaluation of long-term processes governing the behaviour of uranium mill tailings placed in deep lakes

    International Nuclear Information System (INIS)

    1982-03-01

    The emplacement of uranium mill tailings in deep lakes may provide an acceptable method of tailings disposal at certain sites in Canada. Disposal in a depositional environment typical of deep lakes appears to offer greater prospects for long-term stability than present methods of land-based management. From the regulatory point of view, it is necessary to know which factors should be taken into account in assessing the acceptability of such an approach. This report examines the environmental variables governing the behaviour of radionuclides and trace elements in the groundwater systems, lake water, and finally in the biosphere over the short and long term. Physical, chemical and biological factors are each considered. Conclusions are presented in terms of points for and against disposal in deep lakes. This report summarizes the data and conclusions presented in an annex volume

  18. Projective configurations in projectivegeometrical drawings

    Directory of Open Access Journals (Sweden)

    Ivashchenko Andrey Viktorovich

    2015-05-01

    Full Text Available The article focuses on the optimization of the earlier discussed computer method of obtaining new forms of polyhedra based on projective geometry drawings (trace Diagrams.While working on getting new multifaceted forms by projective geometry methods based on the well-known models of polyhedra on the first stage of the work it is required to calculate the parameters of projective geometry drawings, and then to build them. This is an often used apparatus of analytical geometry. According to it, at first the parameters of the polyhedron (core system of planes are calculated, then we obtain the equation of the plane of the face of the polyhedron, and finally we obtain the equations of lines the next plane faces on the selected curve plane. At each stage of application such a method requires the use of the algorithms of floating point arithmetic, on the one hand, leads to some loss of accuracy of the results and, on the other hand, the large amount of computer time to perform these operations in comparison with integer arithmetic operations.The proposed method is based on the laws existing between the lines that make up the drawing - the known configurations of projective geometry (complete quadrilaterals, configuration of Desargues, Pappus et al..The authors discussed in detail the analysis procedure of projective geometry drawing and the presence of full quadrilaterals, Desargues and Pappus configurations in it.Since the composition of these configurations is invariant with respect to projective change of the original nucleus, knowing them, you can avoid the calculations when solving the equations for finding direct projective geometry drawing analytically, getting them on the basis of belonging to a particular configuration. So you can get a definite advantage in accuracy of the results, and in the cost of computer time. Finding these basic configurations significantly enriches the set of methods and the use of projective geometry drawings.

  19. Electroplastic drawing of stainless steels

    International Nuclear Information System (INIS)

    Troitskij, O.A.; Spitsyn, V.I.; Sokolov, N.V.; Ryzhkov, V.G.

    1977-01-01

    Effect of electroplastic drawing on mechanical, magnetic and electrical properties of wire of 12Kh18N10T and Kh13N13M2 steels was studied. Pulse, direct and alternating currents were used. Direct and alternating current densities were 400 A/mm 2 , mean density of pulse current was 200 A/mm 2 . The investigations have shown that the current density increase results in decreasing the wire strengthening intensity though in increasing plastic properties. As a result of electroplastic drawing the growth of magnetic characteristics of wire occurs

  20. Re-processing of Shallow and Deep Crustal Reflection Seismic Data along BABEL Line 7, Central Sweden

    OpenAIRE

    Shahrokhi, Hanieh

    2012-01-01

    The BABEL project (Baltic And Bothnian Echoes from the Lithosphere) was a collaboration among British, Danish, Finnish, German and Swedish geoscientists to acquire deep-crustal reflection and wide-angle refraction data in the Baltic Shield and Gulf of Bothnia. In 1989, the collection of 2,268 km of deep marine reflection seismic data was carried out. BABEL line 7, one of several BABEL profiles, is the focus of this study and runs north of the Åland islands, in an E-W direction in the Bothnian...