WorldWideScience

Sample records for dcb sandwich specimen

  1. A J Integral Approach for Measuring Cohesive Laws Using a Modified DCB Sandwich Specimen

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Berggreen, Christian; Sørensen, Bent F.

    2007-01-01

    mode mixities. The sandwich specimen consists of glass fiber faces and Divinycell H200 foam core. Arbitrary stiffening of the sandwich specimen with steel bars adhered to the faces reduces rotations and ensures that the method is useable for a wide range of materials. The J integral is employed...... and the opening of the pre-crack tip is recorded by a commercial digital photogrammetry measurement system. Cohesive laws are extracted by differentiating J with respect to the normal and tangential opening of the pre-crack tip. Some results are presented and discussed....

  2. A modified DCB sandwich specimen for measuring mixed-mode cohesive laws

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Sørensen, Bent F.; Berggreen, Christian;

    2008-01-01

    A test method is described for measuring cohesive laws for interfaces in sandwich structures. It is proposed to increase the bending stiffness of the sandwich faces by adhering steel bars onto the sandwich faces. This stiffening reduces rotations and ensures that the method is applicable for thin...... which mixed-mode cohesive laws are extracted....

  3. Fracture Testing of Honeycomb Core Sandwich Composites Using the DCB-UBM Test

    DEFF Research Database (Denmark)

    Saseendran, Vishnu; Berggreen, Christian; Carlsson, Leif A.

    2015-01-01

    of the face/core interface. In this paper, a novel test-rig exploiting the double cantilever beam-uneven bending moments (DCB-UBM) concept is used to determine the fracture toughness of aircraft type honeycomb core sandwich composites as a function of the phase angle (mode-mixity), within the framework......Face/core debonds in sandwich structures cause loss of integrity of sandwich structures. The debond problem in honeycomb core sandwich composites has not been widely studied. A suitable fracture approach coupled with experimental validation is paramount to determine the fracture resistance...... of Linear Elastic Fracture Mechanics (LEFM). The Double Cantilever Beam subjected to Uneven Bending Moments (DCB-UBM) test set-up, which was introduced by Sørensen.et.al [1], circumvents any dependency of the pre-crack length in calculation of Gc. The new test setup is based on rotary actuators which...

  4. Discrete Spring Model for Predicting Delamination Growth in Z-Fiber Reinforced DCB Specimens

    Science.gov (United States)

    Ratcliffe, James G.; OBrien, T. Kevin

    2004-01-01

    Beam theory analysis was applied to predict delamination growth in Double Cantilever Beam (DCB) specimens reinforced in the thickness direction with pultruded pins, known as Z-fibers. The specimen arms were modeled as cantilever beams supported by discrete springs, which were included to represent the pins. A bi-linear, irreversible damage law was used to represent Z-fiber damage, the parameters of which were obtained from previous experiments. Closed-form solutions were developed for specimen compliance and displacements corresponding to Z-fiber row locations. A solution strategy was formulated to predict delamination growth, in which the parent laminate mode I critical strain energy release rate was used as the criterion for delamination growth. The solution procedure was coded into FORTRAN 90, giving a dedicated software tool for performing the delamination prediction. Comparison of analysis results with previous analysis and experiment showed good agreement, yielding an initial verification for the analytical procedure.

  5. Tailoring Sandwich Face/Core Interfaces for Improved Damage Tolerance

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Berggreen, Christian; Carlsson, Leif A.

    2010-01-01

    Various modifications of the face/core interface in foam core sandwich specimens are examined in a series of two papers. This paper constitutes part I and describes the finite element analysis of a sandwich test specimen, i.e. a DCB specimen loaded by uneven bending moments (DCB-UBM). Using...

  6. DCB Funding

    Science.gov (United States)

    The Division of Cancer Biology (DCB) funds and supports extramural basic research that investigates the fundamental biology behind cancer. Find out more about DCB's grants process and funding opportunities.

  7. Design Analysis of the Mixed Mode Bending Sandwich Specimen

    DEFF Research Database (Denmark)

    Quispitupa, Amilcar; Berggreen, Christian; Carlsson, Leif A.

    2010-01-01

    A design analysis of the mixed mode bending (MMB) sandwich specimen for face–core interface fracture characterization is presented. An analysis of the competing failure modes in the foam cored sandwich specimens is performed in order to achieve face–core debond fracture prior to other failure modes....... The analysis facilitates selection of the appropriate geometry for the MMB sandwich specimen to promote debond failure. An experimental study is performed using MMB sandwich specimens with a H100 PVC foam core and E-glass–polyester faces. The results reveal that debond propagation is successfully achieved...... for the chosen geometries and mixed mode loading conditions....

  8. A general mixed mode fracture mechanics test specimen: The DCB-specimen loaded with uneven bending moments

    DEFF Research Database (Denmark)

    Sørensen, Bent F.; Jørgensen, K.; Jacobsen, T.K.;

    2004-01-01

    A mixed mode specimen is proposed for fracture mechanics characterisation of adhesive joints, laminates and multilayers. The specimen is a double cantilever beam specimen loaded with uneven bending moments at the two free beams. By varying the ratiobetween the two applied moments, the full mode...

  9. A Debonded Sandwich Specimen Under Mixed Mode Bending (MMB)

    DEFF Research Database (Denmark)

    Quispitupa, Amilcar; Berggreen, Christian; Carlsson, Leif A.

    2008-01-01

    Face/core interface crack propagation in sandwich specimens is analyzed. A thorough analysis of the typical failure modes in sandwich composites was performed in order to design the MMB specimen to promote face/core debond fracture. Displacement, compliance and energy release rate expressions...... for the MMB specimen were derived from a superposition analysis. An experimental verification of the methodology proposed was performed using MMB sandwich specimens with H100 PVC foam core and E-glass/polyester non-crimp quadro-axial [0/45/90/-45]s DBLT-850 faces. Different mixed mode loadings were applied...

  10. A Debonded Sandwich Specimen Under Mixed Mode Bending (MMB)

    DEFF Research Database (Denmark)

    Quispitupa, Amilcar; Berggreen, Christian; Carlsson, Leif A.

    2008-01-01

    Face/core interface crack propagation in sandwich specimens is analyzed. A thorough analysis of the typical failure modes in sandwich composites was performed in order to design the MMB specimen to promote face/core debond fracture. Displacement, compliance and energy release rate expressions...... for the MMB specimen were derived from a superposition analysis. An experimental verification of the methodology proposed was performed using MMB sandwich specimens with H100 PVC foam core and E-glass/polyester non-crimp quadro-axial [0/45/90/-45]s DBLT-850 faces. Different mixed mode loadings were applied...

  11. Text Fixture for Double Cantilever Beam (DCB) Specimens Subjected to Uneven Bending Moments

    DEFF Research Database (Denmark)

    Svenninggaard, Jon; Andreasen, Jens; Bak, Brian

    2017-01-01

    With the increased use of modern lightweight materials like layered fibre reinforced polymers there is an inherent demand to characterize their properties. One of the critical failure modes in layered materials is delamination due to the low out of plane strength. To characterize the interface...... as well as a 23 specially fabricated tool, made from two flat bars, which was fitted with strain gauges to verify that the strain field from the pure moment application. The analysis revealed negligible introductions of shear forces to the specimens....

  12. Mixed mode fracture toughness characterization of sandwich interfaces using the modified TSD specimen

    DEFF Research Database (Denmark)

    Berggreen, Christian; Andreasen, J.H.; Carlsson, L.A.;

    2009-01-01

    An extensive parametric analysis shows that the modified Tilted Sandwich Debond (TSD) specimen provides a methodology for characterization of the face/core fracture resistance over a range of mode-mixities. A pilot experimental mixed mode characterization of the fracture toughness of sandwich spe...

  13. On the analysis of a mixed mode bending sandwich specimen for debond fracture characterization

    DEFF Research Database (Denmark)

    Quispitupa, Amilcar; Berggreen, Christian; Carlsson, Leif A.

    2009-01-01

    The mixed mode bending specimen originally developed for mixed mode delamination fracture characterization of unidirectional composites has been extended to the study of debond propagation in foam cored sandwich specimens. The compliance and strain energy release rate expressions for the mixed mode...... bending sandwich specimen are derived based on a superposition analysis of solutions for the double cantilever beam and cracked sandwich beam specimens by applying a proper kinematic relationship for the specimen deformation combined with the loading provided by the test rig. This analysis provides also...... expressions for the global mode mixities. An extensive parametric analysis to improve the understanding of the influence of loading conditions, specimen geometry and mechanical properties of the face and core materials has been performed using the derived expressions and finite element analysis. The mixed...

  14. Face/core interface fracture characterization of mixed mode bending sandwich specimens

    DEFF Research Database (Denmark)

    Quispitupa, Amilcar; Berggreen, Christian; Carlsson, L.A.

    2011-01-01

    application point (lever arm distance). Finite element analysis was performed to determine the mode‐mixity at the crack tip. The results showed that the face/core interface fracture toughness increased with increased mode II loading. Post failure analysis of the fractured specimens revealed that the crack......Debonding of the core from the face sheets is a critical failure mode in sandwich structures. This paper presents an experimental study on face/core debond fracture of foam core sandwich specimens under a wide range of mixed mode loading conditions. Sandwich beams with E‐glass fibre face sheets...... and PVC H45, H100 and H250 foam core materials were evaluated. A methodology to perform precracking on fracture specimens in order to achieve a sharp and representative crack front is outlined. The mixed mode loading was controlled in the mixed mode bending (MMB) test rig by changing the loading...

  15. Face/core debond fatigue crack growth characterization using the sandwich mixed mode bending specimen

    DEFF Research Database (Denmark)

    Manca, Marcello; Quispitupa, Amilcar; Berggreen, Christian;

    2012-01-01

    Face/core fatigue crack growth in foam-cored sandwich composites is examined using the mixed mode bending (MMB) test method. The mixed mode loading at the debond crack tip is controlled by changing the load application point in the MMB test fixture. Sandwich specimens were manufactured using H45...... critical load, at load ratios of R=0.1 and 0.2. The crack length was determined during fatigue testing using the analytical compliance expression and verified by visual measurements. Fatigue crack growth results revealed higher crack growth rates for mode I dominated loading. For specimens with H45 core...

  16. Measuring Cohesive Laws for Interfaces in Sandwich Structures

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Sørensen, Bent F.; Berggreen, Carl Christian

    2006-01-01

    Extraction of cohesive laws are conducted for interfaces in sandwich structures. Separation between face and core are driven by pure bending moments applied to double cantilever beam (DCB) specimens. By varying the ratio between moments applied to the beams the test is conducted for different mode...... mixities. The sandwich specimens consists of glass fiber faces and Divinycell H200 foam core with a pre-crack between face and core made with teflon film. Arbitrary stiffening of the sandwich faces with steel bars adhered to the faces reduces rotations and ensures that the method is useable for a wide...

  17. Measuring Cohesive Laws for Interfaces in Sandwich Structures

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Sørensen, Bent F.; Berggreen, Carl Christian

    2006-01-01

    Extraction of cohesive laws are conducted for interfaces in sandwich structures. Separation between face and core are driven by pure bending moments applied to double cantilever beam (DCB) specimens. By varying the ratio between moments applied to the beams the test is conducted for different mode...... mixities. The sandwich specimens consists of glass fiber faces and Divinycell H200 foam core with a pre-crack between face and core made with teflon film. Arbitrary stiffening of the sandwich faces with steel bars adhered to the faces reduces rotations and ensures that the method is useable for a wide...

  18. Analysis of crack propagation in nuclear graphite using three-point bending of sandwiched specimens

    Energy Technology Data Exchange (ETDEWEB)

    Shi Li; Li Haiyan; Zou Zhenmin [School of Mechanical, Aerospace and Civil Engineering, University of Manchester, P.O. Box 88, Sackville Street, Manchester M60 1QD (United Kingdom); Fok, Alex S.L. [School of Mechanical, Aerospace and Civil Engineering, University of Manchester, P.O. Box 88, Sackville Street, Manchester M60 1QD (United Kingdom)], E-mail: alex.fok@manchester.ac.uk; Marsden, Barry J. [School of Mechanical, Aerospace and Civil Engineering, University of Manchester, P.O. Box 88, Sackville Street, Manchester M60 1QD (United Kingdom); Hodgkins, Andrew; Mummery, Paul M.; Marrow, James [School of Materials, University of Manchester, Grosvenor St., Manchester M1 7HS (United Kingdom)

    2008-01-31

    The aim of this paper was to assess the suitability of the sandwiched beam in three-point bending as a technique for determining fracture toughness and R-curve behaviour of nuclear graphite using small beam specimens. Surface displacements of the cracked beam specimen were measured using Electronic Speckle Pattern Interferometry (ESPI) and Image Correlation in order to accurately monitor crack propagation and frictional contact between the test specimen and the sandwiching beams. The results confirmed that solutions based on the simple beam theory could overestimate the fracture toughness of graphite. Finite element analysis using a Continuum Damage Mechanics failure model indicated that both friction and shape of the notch played an important part in providing resistance to crack growth. Inclusion of these factors and the use of more accurate load vs. crack length curves derived from the FE model would provide a satisfactory measure of fracture toughness in small beam specimens under such a loading configuration. The particular graphite tested, IG-110, showed a decrease in fracture toughness with increasing crack length.

  19. Improving Performance of Polymer Fiber Reinforced Sandwich X-Joints in Naval Vessels

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Berggreen, Christian; Karlsen, Kasper;

    2007-01-01

    This study deals with damage tolerance of sandwich X-joints with embedded debond damages between face and core. The study is conducted both through modeling and full-scale tests. Mixed mode cohesive laws from the opening of sandwich interfaces are determined experimentally from a DCB specimen...... loaded by moments, and the results are utilized in a cohesive zone model of a tested sandwich structure. Results of the crack propagation from experiments and simulation show fair agreement. Design aspects regarding the influence of debond size and core inserts on the residual strength are discussed....

  20. On the use of a woven mat to control the crack path in composite sandwich structures

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Berggreen, Christian; Carlsson, Leif A.

    2008-01-01

    cantilever beam specimen loaded by unequal bending moments (DCB-UBM specimen) [6, 7], see Figure 2. The specimen is loaded by a roller-wire system mounted in a tensile test machine. The ratio between the two applied moments (M1/M2) is dictated by the ratio between roller distances (I1/I2), see Figure 2...

  1. Determination of the size dependence of the energy release rate for mode I loaded DCB specimens

    DEFF Research Database (Denmark)

    Svenninggaard, Jon

    2015-01-01

    Large scale bridging in delamination of fiber reinforced composites is an important mechanism that is important to understand. In for example wind turbine blade design, this is of great importance as cracks may propagate from resin filled areas, wrinkles, air bubbles or manufacturing defects...

  2. Determination of the Mode I Interlaminar Fracture Toughness by Using a Nonlinear Double-Cantilever Beam Specimen

    Science.gov (United States)

    Pavelko, V.; Lapsa, K.; Pavlovskis, P.

    2016-07-01

    The aim of this study is estimation of the effect of large deflections of a double-cantilever beam (DCB) on the accuracy of determination of the mode I interlaminar fracture toughness GIc of layered composites by using the nonlinear theory of bending of beams. The differential equation of the deflection curve of arm of the DCB specimen in the natural form was used to analyze the strain energy of the specimen and its strain energy release rate GI upon propagation of delamination under the action of cleavage forces at the ends of cantilevers. An algorithm for calculating the strain energy and its release rate in the DCB specimens is realized in the form of a MATLAB code. An experimental study was carried out on DCB specimens of a highly flexible carbon/epoxy laminate. The validity of the nonlinear model developed is demonstrated. The standard methods used to determine GIc are refined for the case of highly flexible specimens.

  3. Sandwich Panels

    Directory of Open Access Journals (Sweden)

    N. Ramachandran

    1963-05-01

    Full Text Available This introductory article give an insight into the different methods employed in the construction of Sandwich panels, their limitations and future design application for defence use as a structural element with one of the highest strength-weight ratios yet devised.

  4. Sandwich construction

    Science.gov (United States)

    Marshall, A.

    A form of composites known as structural sandwich construction is presented in terms of materials used, design details for solving edging and attachment problems, and charts of design material analysis. Sandwich construction is used in nearly all commercial airliners and helicopters, and military air and space vehicles, and it is shown that this method can stiffen a structure without causing a weight increase. The facing material can be made of 2024 or 7075 aluminum alloy, titanium, or stainless steel, and the core material can be wood or foam. The properties of paper honeycomb and various aluminum alloy honeycombs are presented. Factors pertaining to adhesive materials are discussed, including products given off during cure, bonding pressure, and adaptability. Design requirements and manufacturing specifications are resolved using numerous suggestions.

  5. Advanced Mechanical Testing of Sandwich Materials

    DEFF Research Database (Denmark)

    Hayman, Brian; Berggreen, Christian; Jenstrup, Claus

    2008-01-01

    An advanced digital optical system has been used to measure surface strains on sandwich face and core specimens tested in a project concerned with improved criteria for designing sandwich X-joints. The face sheet specimens were of glass reinforced polyester and were tested in tension. The core...... specimens were of PVC foam and were tested in compression. The tests were performed in order to validate the use of the measurement system on these materials and to obtain material data for use in numerical simulations. While some limitations were identified, the optical system performed well and appears...

  6. An Accurate Method for the BDS Receiver DCB Estimation in a Regional Network

    Directory of Open Access Journals (Sweden)

    LI Xin

    2016-08-01

    Full Text Available An accurate approach for receiver differential code biases (DCB estimation is proposed with the BDS data obtained from a regional tracking network. In contrast to the conventional methods for BDS receiver DCB estimation, the proposed method does not require a complicated ionosphere model, as long as one reference station receiver DCB is known. The main idea for this method is that the ionosphere delay is highly dependent on the geometric ranges between the BDS satellite and the receiver normally. Therefore, the non-reference station receivers DCBs in this regional area can be estimated using single difference (SD with reference stations. The numerical results show that the RMS of these estimated BDS receivers DCBs errors over 30 days are about 0.3 ns. Additionally, after deduction of these estimated receivers DCBs and knowing satellites DCBs, the extractive diurnal VTEC showed a good agreement with the diurnal VTEC gained from the GIM interpolation, indicating the reliability of the estimated receivers DCBs.

  7. Development and Evaluation of Stitched Sandwich Panels

    Science.gov (United States)

    Stanley, Larry E.; Adams, Daniel O.; Reeder, James R. (Technical Monitor)

    2001-01-01

    This study explored the feasibility and potential benefits provided by the addition of through-the-thickness reinforcement to sandwich structures. Through-the-thickness stitching is proposed to increase the interlaminar strength and damage tolerance of composite sandwich structures. A low-cost, out-of-autoclave processing method was developed to produce composite sandwich panels with carbon fiber face sheets, a closed-cell foam core, and through-the-thickness Kevlar stitching. The sandwich panels were stitched in a dry preform state, vacuum bagged, and infiltrated using Vacuum Assisted Resin Transfer Molding (VARTM) processing. For comparison purposes, unstitched sandwich panels were produced using the same materials and manufacturing methodology. Test panels were produced initially at the University of Utah and later at NASA Langley Research Center. Four types of mechanical tests were performed: flexural testing, flatwise tensile testing, core shear testing, and edgewise compression testing. Drop-weight impact testing followed by specimen sectioning was performed to characterize the damage resistance of stitched sandwich panels. Compression after impact (CAI) testing was performed to evaluate the damage tolerance of the sandwich panels. Results show significant increases in the flexural stiffness and strength, out-of-plane tensile strength, core shear strength, edgewise compression strength, and compression-after-impact strength of stitched sandwich structures.

  8. Sandwich DIY

    Institute of Scientific and Technical Information of China (English)

    肖蕾

    2006-01-01

    我们都知道sandwich是一种方便食品,就是在两片面包中加上一些肉和蔬菜。Sandwich这个名字来源于英国的一位桑威治伯爵(Earl of Sandwich)。据说这位伯爵嗜赌如命,就是到吃饭的时候也不愿停下来。于是他就叫侍者把肉、蛋、菜夹在面包片中,让他拿在手上边赌边吃。后来人们就把这种夹馅面包叫做sandwich。现在sandwich已成为风靡世界的快餐食品(snack)了。Sandwich的做法其实很简单。如果你有两片面包,你几乎可以在这两片面包之间夹上任何食物来给自己做一个三明治。下面就让我们试一试,做一个三明治来吃。第一步:在一片面包上抹上黄油(butter)或植物黄油,在另一片面包上抹上蛋黄酱(mayonnaise)和芥末酱(mustard)。喜欢吃番茄酱(catsup)也可以放番茄酱!第二步:把花生酱(peanut butter)或者乳酪片(cream)、熟肉片放在涂了黄油的面包片上。想吃什么肉就放什么肉,香肠也可以!第三步:在乳酪上面放酸黄瓜片、番茄片和生菜。也可以根据个人的口味再放些乳酪、芥末酱和(或)番茄酱、洋葱、辣椒、盐、黑胡椒和醋。第四步:将第二片面包盖在上面,就做成了一个sand...

  9. Rapid determination method for 2-DCB in irradiated pork by ASE-Al2O3-GC-MS

    Science.gov (United States)

    Li, An; Pan, Li-Gang; Zhang, Xiu-Tong; Jin, Xin-Xin; Ma, Hong-Zao

    2017-01-01

    2-Dodecylcyclobutanone (2-DCB) is validated as a marker for irradiated foodstuffs. However, the preparation methods for the marker compound involve time-consuming and tedious procedures prior to analysis. This paper describes a rapid method for the extraction and cleanup of 2-DCB in irradiated pork. The highly automated extraction procedure is based on accelerated solvent extraction combined with a purification step by Al2O3, which is added to the extraction cell. The overall extraction time is less than 20 min, and the volume of the solvent is 1.5 times that of the extraction cell (34 mL). The recovery of 2-DCB from pork samples for this method is higher than 75%. The method allows detecting pork irradiated at low doses (0.5 kGy). The proposed method is considered an alternative to the Soxhlet extraction and Florisil chromatography method currently in use.

  10. The sandwich sign

    Directory of Open Access Journals (Sweden)

    Nasreen Mahomed

    2012-09-01

    Full Text Available The sandwich sign refers to the sandwiching of mesenteric vessels and fat by enlarged mesenteric nodes on cross-sectional imaging, commonly occurring in lymphoma, but not specific to lymphoma. The sign is radiologically indistinguishable from post-transplant lymphoproliferative disorders. The radiological significance of the sandwich sign is in suggesting the diagnosis of lymphoma so that appropriate treatment may be initiated early as the tumour has a rapid growth pattern.

  11. Receiver DCB estimation and GPS vTEC study at a low latitude station in the South Pacific

    Science.gov (United States)

    Prasad, Ramendra; Kumar, Sushil; Jayachandran, P. T.

    2016-11-01

    The statistical estimation of receiver differential code bias (DCB) of the GSV4004B receiver at a low latitude station, Suva (lat. 18.15°S, long. 178.45°E, Geomag. Lat. 21.07°S), Fiji, and the subsequent behaviour of vTEC, are presented. By means of least squares linear regression fitting technique, the receiver DCB was determined using the GPS vTEC data recorded during the year 2010, CODE TEC and IRI-2012 model for 2010. To substantiate the results, minimization of the standard deviation (SD) method was also used for GPS vTEC data. The overall monthly DCB was estimated to be in the range of 62.6 TECU. The vTEC after removing the resultant monthly DCB was consistent with other low latitude observations. The GPS vTEC 2010 data after eliminating the resultant DCB were lower in comparison to Faraday rotation vTEC measurements at Suva during 1984 primarily due to higher solar activity during 1984 as compared to 2010. Seasonally, vTEC was maximum during summer and minimum during winter. The winter showed least vTEC variability whereas equinox showed the largest daytime variability. The geomagnetic disturbances effect showed that both vTEC and its variability were higher on magnetically disturbed days as compared to quiet days with maximum variability in the daytime. Two geomagnetic storms of moderate strengths with main phases in the local daytime showed long duration (∼52 h) increase in vTEC by 33-67% which can be accounted by changes in E×B drifts due to prompt penetration of storm-time auroral electric field in the daytime and disturbance dynamo electric field in the nighttime to low latitudes.

  12. Interface fatigue crack propagation in sandwich X-joints – Part I: Experiments

    DEFF Research Database (Denmark)

    Moslemian, Ramin; Berggreen, Christian

    2013-01-01

    In this study, face/core fatigue crack growth in sandwich X-joints is investigated numerically and experimentally. The work presented here covers Part I of the study which includes an experimental investigation of fatigue crack growth in sandwich X-joints and characterization of the face/core int......In this study, face/core fatigue crack growth in sandwich X-joints is investigated numerically and experimentally. The work presented here covers Part I of the study which includes an experimental investigation of fatigue crack growth in sandwich X-joints and characterization of the face....../core interface of the joints. Sandwich tear test specimens with a face/core debond representing a debonded sandwich X-joint were tested under cyclic loading. Fatigue tests were conducted on the sandwich tear test specimens with H45, H100 and H250 PVC cores and glass/polyester face sheets. The Digital Image...

  13. Estimation of BDS DCB Combining GIM and Different Zero-mean Constraints

    Directory of Open Access Journals (Sweden)

    YAO Yibin

    2017-02-01

    Full Text Available As the limited number of the BeiDou Navigation Satellite System (BDS satellites and tracking stations currently, it's difficult to attain daily DCBs solution with precisely high accuracy based on BeiDou single system. In order to overcome the weakness above, two different zero-mean constraints for BDS satellites, called constraint one and constraint two, respectively, are used to estimate DCBs of BDS based on BeiDou observations from the multi-GNSS experiment (MGEX network and global ionosphere maps (GIM from the Center for Orbit Determination in Europe (CODE. The results show that the systematic difference of the overall trend under two different constraints is consistent, and the systematic difference of DCBC2I-C7I and DCBC2I-C6I is -3.3 ns and 1.2 ns, respectively. The systematic difference between BDS satellite DCBs and receiver DCBs has the same absolute value, but opposite signs instead. Compared to constraint one, The DCBs estimation of IGSO/MEO satellites under constraint two are more stable (the improvement of satellites DCBC2I-C7I and DCBC2I-C6I STD are up to 21%, 13%, respectively, the stability of IGSO and MEO satellites (STDs are within 0.1 ns, 0.2 ns, respectively is better than that of GEO satellites (STDs are 0.15~0.32 ns. DCB estimation of constraint one is not only consistent with the CAS/DLR products (Bias:-0.4~0.2 ns, but also takes into account the stability of BDS satellites DCB. Under the two different constraints, there is no obvious change in BDS receiver DCBs, meaning that the selection of constraints has no obvious influence on the stability of BDS receivers DCBs. The overall stability of BDS receiver DCBs is better than 1 ns. Due to the accuracy discrepancy of GIM in different latitudes, the stability of BDS receiver DCBs in the middle-high latitude (STDs are within 0.4 ns is better than that in low latitude region (STDs are 0.8~1 ns.

  14. Influences of the day-night differences of ionosphere on the GPS DCB estimation

    Science.gov (United States)

    Zhang, Donghe; Zhang, Shunrong; Coster, Anthea; Hao, Yongqiang; Xiao, Zuo

    2016-04-01

    The estimation of differential code bias (DCB) of GPS system is one of the necessary steps for total electron content (TEC) derivation from GPS measurements. Usually, the method for estimating the GPS DCBs follows the assumption of the gentle temporal and spatial variation of the ionosphere, but this assumption is just an approximation because of the ionosphere's inherent variability. It has been indicated that the estimated GPS satellite DCBs are sometimes influenced by the ionospheric conditions. Here, we demonstrate a possible influence of ionospheric condition that differs between day and night on the estimated DCBs from measurements of a single GPS station. It is found that the average standard deviations (STDs) of the satellite DCBs estimated with daytime data are higher than that with the nighttime data. To reduce this day-night difference effect on GPS DCB determination, we use an improved estimation method based on the primary features of the ionospheric variability with local time. A local time dependent weighting function was introduced into the original least-squared DCBs estimation algorithm. A test with data for BJFS station (39.60°N, 115.89°E) in 2001 indicates that the STD of the DCBs decreases from 2.533 TECU to 2.308 TECU, or by 8.9%, after the improved method was applied. For comparison, another test for the same station in 2009 indicates that the STD decreases from 1.344TECU to 1.295 TECU. Reference Li, LX. DH. Zhang., SR. Zhang., et al. Influences of the day-night differences of ionospheric variability on the estimation of GPS differential code bias, Radio Science, 2015, DOI: 10.1002/2014RS005565 Zhang D H, Shi H, Jin Y Q, et al. The variation of the estimated GPS instrumental bias and its possible connection with ionospheric variability. Sci China Tech Sci, 2014, 57: 67-79, doi: 10.1007/s11431-013-5419-7 Zhang D H, Zhang W,Li Q., Accuracy analysis of the GPS instrumental bias estimated from observations in middle and low latitudes

  15. Sandwich Panels Evaluated With Ultrasonic Spectroscopy

    Science.gov (United States)

    Cosgriff, Laura M.

    2004-01-01

    Enhanced, lightweight material systems, such as 17-4PH stainless steel sandwich panels are being developed for use as fan blades and fan containment systems for next-generation engines. The bond strength between the core and face sheets is critical in maintaining the structural integrity of the sandwich structure. To improve the inspection and production of these systems, researchers at the NASA Glenn Research Center are using nondestructive evaluation (NDE) techniques, such as ultrasonic spectroscopy, to evaluate the brazing quality between the face plates and the metallic foam core. The capabilities and limitations of a swept-frequency approach to ultrasonic spectroscopy were evaluated with respect to these sandwich structures. This report discusses results from three regions of a sandwich panel representing different levels of brazing quality between the outer face plates and a metallic foam core. Each region was investigated with ultrasonic spectroscopy. Then, on the basis of the NDE results, three shear specimens sectioned from the sandwich panel to contain each of these regions were mechanically tested.

  16. Genome sequence of Desulfitobacterium hafniense DCB-2, a Gram-positive anaerobe capable of dehalogenation and metal reduction

    Directory of Open Access Journals (Sweden)

    Kim Sang-Hoon

    2012-02-01

    Full Text Available Abstract Background The genome of the Gram-positive, metal-reducing, dehalorespiring Desulfitobacterium hafniense DCB-2 was sequenced in order to gain insights into its metabolic capacities, adaptive physiology, and regulatory machineries, and to compare with that of Desulfitobacterium hafniense Y51, the phylogenetically closest strain among the species with a sequenced genome. Results The genome of Desulfitobacterium hafniense DCB-2 is composed of a 5,279,134-bp circular chromosome with 5,042 predicted genes. Genome content and parallel physiological studies support the cell's ability to fix N2 and CO2, form spores and biofilms, reduce metals, and use a variety of electron acceptors in respiration, including halogenated organic compounds. The genome contained seven reductive dehalogenase genes and four nitrogenase gene homologs but lacked the Nar respiratory nitrate reductase system. The D. hafniense DCB-2 genome contained genes for 43 RNA polymerase sigma factors including 27 sigma-24 subunits, 59 two-component signal transduction systems, and about 730 transporter proteins. In addition, it contained genes for 53 molybdopterin-binding oxidoreductases, 19 flavoprotein paralogs of the fumarate reductase, and many other FAD/FMN-binding oxidoreductases, proving the cell's versatility in both adaptive and reductive capacities. Together with the ability to form spores, the presence of the CO2-fixing Wood-Ljungdahl pathway and the genes associated with oxygen tolerance add flexibility to the cell's options for survival under stress. Conclusions D. hafniense DCB-2's genome contains genes consistent with its abilities for dehalogenation, metal reduction, N2 and CO2 fixation, anaerobic respiration, oxygen tolerance, spore formation, and biofilm formation which make this organism a potential candidate for bioremediation at contaminated sites.

  17. Sandwich classification theorem

    Directory of Open Access Journals (Sweden)

    Alexey Stepanov

    2015-09-01

    Full Text Available The present note arises from the author's talk at the conference ``Ischia Group Theory 2014''. For subgroups FleN of a group G denote by Lat(F,N the set of all subgroups of N , containing F . Let D be a subgroup of G . In this note we study the lattice LL=Lat(D,G and the lattice LL ′ of subgroups of G , normalized by D . We say that LL satisfies sandwich classification theorem if LL splits into a disjoint union of sandwiches Lat(F,N G (F over all subgroups F such that the normal closure of D in F coincides with F . Here N G (F denotes the normalizer of F in G . A similar notion of sandwich classification is introduced for the lattice LL ′ . If D is perfect, i.,e. coincides with its commutator subgroup, then it turns out that sandwich classification theorem for LL and LL ′ are equivalent. We also show how to find basic subroup F of sandwiches for LL ′ and review sandwich classification theorems in algebraic groups over rings.

  18. Determination of the J integral for laminated double cantilever beam specimens: The curvature approach

    OpenAIRE

    Rask, Morten; Sørensen, Bent F

    2012-01-01

    A new approach is proposed for measuring the J integral (and thus the fracture resistance) of interface cracks in multiply laminates. With this approach the J integral is found from beam curvatures and applied moments. Knowledge of ply layup and stiffness is not required. In order to test the accuracy of the proposed approach, double cantilever beam specimen loaded with uneven bending moments (DCB-UBM) specimens were tested and analysed using the curvature approach and a method based on lamin...

  19. Fatigue fracture of fiber reinforced polymer honeycomb composite sandwich structures for gas turbine engines

    Science.gov (United States)

    Nikhamkin, Mikhail; Sazhenkov, Nikolai; Samodurov, Danil

    2017-05-01

    Fiber reinforced polymer honeycomb composite sandwich structures are commonly used in different industries. In particular, they are used in the manufacture of gas turbine engines. However, fiber reinforced polymer honeycomb composite sandwich structures often have a manufacturing flaw. In theory, such flaws due to their rapid propagation reduce the durability of fiber reinforced polymer honeycomb composite sandwich structures. In this paper, bending fatigue tests of fiber reinforced polymer honeycomb composite sandwich structures with manufacturing flaws were conducted. Comparative analysis of fatigue fracture of fiber reinforced polymer honeycomb composite sandwich specimens was conducted before and after their bending fatigue tests. The analysis was based on the internal damage X-ray observation of fiber reinforced polymer honeycomb composite sandwich specimens.

  20. Virtual Specimens

    Science.gov (United States)

    de Paor, D. G.

    2009-12-01

    Virtual Field Trips have been around almost as long as the Worldwide Web itself yet virtual explorers do not generally return to their desktops with folders full of virtual hand specimens. Collection of real specimens on fields trips for later analysis in the lab (or at least in the pub) has been an important part of classical field geoscience education and research for generations but concern for the landscape and for preservation of key outcrops from wanton destruction has lead to many restrictions. One of the author’s favorite outcrops was recently vandalized presumably by a geologist who felt the need to bash some of the world’s most spectacular buckle folds with a rock sledge. It is not surprising, therefore, that geologists sometimes leave fragile localities out of field trip itineraries. Once analyzed, most specimens repose in drawers or bins, never to be seen again. Some end up in teaching collections but recent pedagogical research shows that undergraduate students have difficulty relating specimens both to their collection location and ultimate provenance in the lithosphere. Virtual specimens can be created using 3D modeling software and imported into virtual globes such as Google Earth (GE) where, they may be linked to virtual field trip stops or restored to their source localities on the paleo-globe. Sensitive localities may be protected by placemark approximation. The GE application program interface (API) has a distinct advantage over the stand-alone GE application when it comes to viewing and manipulating virtual specimens. When instances of the virtual globe are embedded in web pages using the GE plug-in, Collada models of specimens can be manipulated with javascript controls residing in the enclosing HTML, permitting specimens to be magnified, rotated in 3D, and sliced. Associated analytical data may be linked into javascript and localities for comparison at various points on the globe referenced by ‘fetching’ KML. Virtual specimens open up

  1. Experimental investigation on vibration characteristics of sandwich beams with magnetorheological elastomers cores

    Institute of Scientific and Technical Information of China (English)

    魏克湘; 孟光; 张文明; 朱石沙

    2008-01-01

    A sandwich beam specimen was fabricated by treating with MR elastomers between two thin aluminum face-plates.Experiment was carried out to investigate the vibration responses of the sandwich beam with respect to the intensity of the magnetic field and excitation frequencies.The results show that the sandwich beams with MR elastomers cores have the capabilities of shifting natural frequencies and the vibration amplitudes decrease with the variation of the intensity of external magnetic field.

  2. Effects of Subzero Temperatures and Sea Water Immersion on Damage Initiation and Growth in Sandwich Composites

    Science.gov (United States)

    2008-12-10

    single cantilever beam sandwich test. The TSD is perhaps 19 An improved methodology for measuring the interracial toughness of sandwich beams 3...measuring the interracial toughness of sandwich beams 5 Table 4.1. Material properties Glass face Glass face Carbon „ , ,, Loading L...which shows the relationship between reaction forces for an MSCB specimen with 12 ply glass face sheets at different crack lengths. It is observed

  3. Predicting safe sandwich production

    DEFF Research Database (Denmark)

    Birk, Tina; Duan, Zhi; Møller, Cleide Oliveira de Almeida

    2014-01-01

    and serving. However, Danish sandwich producing companies find it challenging to comply with this and have expressed a need for more flexibility. The Danish guidelines do allow for a prolongation of the acceptable time outside the cold chain, if the safety of the specific production can be documented....... There is, therefore, room for developing targeted tools for evaluating the time-temperature scenarios in sandwich production. This study describes a decision support tool developed to offer the producers more flexibility. Based on time/temperature measurements obtained during preparation combined......Time and temperature control is crucial to avoid growth of pathogens during production and serving of cold ready-to-eat meals. The Danish guidelines state that chilled foods, such as sandwiches, should not be outside the cold chain for more than 3 hours including the time for preparation...

  4. Self-healing sandwich composite structures

    Science.gov (United States)

    Fugon, D.; Chen, C.; Peters, K.

    2012-04-01

    Previous research demonstrated that a thin self-healing layer is effective in recovering partial sandwich composite performance after an impact event. Many studies have been conducted that show the possibility of using Fiber Bragg Grating (FBG) sensors to monitor the cure of a resin through strain and temperature monitoring. For this experiment, FBG sensors were used to monitor the curing process of a self-healing layer within a twelve-layer fiberglass laminate after impact. First, five self-healing sandwich composite specimens were manufactured. FBG sensors were embedded between the fiberglass and foam core. Then the fiberglass laminate was impacted with the use of a drop tower and the curing process was monitored. The collected data was used to compare the cure of the resin and fiberglass alone to the cure of the resin from a self-healing specimen. For the low viscosity resin system tested, these changes were not sufficiently large to identify different polymerization states in the resin as it cured. These results indicate that applying different resin systems might increase the efficiency of the self-healing in the sandwich composites.

  5. On Sandwiched Singularities

    OpenAIRE

    Möhring, Konrad

    2004-01-01

    Sandwich-Singularitäten sind die Singularitäten auf derNormalisierung von Aufblasungen eines regulärenFlächenkeimes. In der Arbeit wird ein enger Zusammenhangzwischen Topologie und Deformationstheorie vonSandwich-Singularitäten einerseits und ebenenKurvensingularitäten andererseits dargestellt. NeueErgebnisse betreffen u.a. Deformationen vonnulldimensionalen komplexen Räumen in der Ebene, die durchvollständige Ideale beschrieben werden, z.B. wann'simultanes Aufblasen' der Fasern einer solchen...

  6. A study of structurally efficient graphite-thermoplastic trapezoidal-corrugation sandwich and semi-sandwich panels

    Science.gov (United States)

    Jegley, Dawn C.

    1993-01-01

    The structural efficiency of compression-loaded trapezoidal-corrugation sandwich and semi-sandwich composite panels is studied to determine their weight savings potential. Sandwich panels with two identical face sheets and a trapezoidal corrugated core between them, and semi-sandwich panels with a corrugation attached to a single skin are considered. An optimization code is used to find the minimum weight designs for critical compressive load levels ranging from 3,000 to 24,000 lb/in. Graphite-thermoplastic panels based on the optimal minimum weight designs were fabricated and tested. A finite-element analysis of several test specimens was also conducted. The results of the optimization study, the finite-element analysis, and the experiments are presented.

  7. Detecting and identifying damage in sandwich polymer composite by using acoustic emission

    DEFF Research Database (Denmark)

    McGugan, M.; Sørensen, Bent F.; Østergaard, R.

    2006-01-01

    Acoustic emission is a useful monitoring tool for extracting extra information during mechanical testing of polymer composite sandwich materials. The study of fracture mechanics within test specimens extracted from wind turbine blade material ispresented. The contribution of the acoustic emission...

  8. Origin of Sandwich

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    In every language there are words that have some interesting stories behind them. The word “sandwich” forexample, is very common in English. If we want to know the story behind it, we must know something about an English nobleman named Sandwich who lived in the 18th century.

  9. Making a Sandwich

    Institute of Scientific and Technical Information of China (English)

    郭富强

    2011-01-01

    Do you like eating sandwiches? Here is a recipe(做法) for a fruit sandwich.First , you should put butter(黄油)on two slices(片) of bread. Next, peel(剥开) three bananas. Now cut up(切碎) these three bananas and apple.

  10. Enhanced Performance of Sandwich Structures by Improved Damage Tolerance

    DEFF Research Database (Denmark)

    Martakos, Georgios

    The PhD thesis investigates the enhancement of the damage tolerance of sandwich structures by the embedding of a new type of core inserts that act as face/core interface crack stopping elements. The thesis presents series of experimental investigations where the new crack stopping elements...... are embedded in both sandwich beam and panel specimens. The experimental observations form the basis for evaluating the efficiency of the proposed crack stopping inserts. For the experiments, Digital Image Correlation (DIC) was used to characterize the measure the local strain fields and overall deformation...... behaviour around the new crack stopper elements. In support for the experimental investigations, a Finite Element (FE) analysis based methodology, including fracture mechanics analysis and the so-called ‘cycle jump’ technique, was developed to predict the progression of damage in sandwich specimens...

  11. Sandwiched composites in aerospace engineering

    OpenAIRE

    Nunes, J. P.; Silva,J.F.

    2016-01-01

    This chapter considers sandwiched composites used in aerospace applications. Typical sandwich composites consist of two thin, stiff, high-strength facing skins separated by a thick and light core. New developments in the type of face and core materials, production methods and joining and repair techniques are discussed in this chapter. It also discusses various properties as well as their main design methods for existing and future applications of sandwiched composites.

  12. G-control fatigue testing for cyclic crack propagation in composite structures

    DEFF Research Database (Denmark)

    Manca, Marcello; Berggreen, Christian; Carlsson, Leif A.

    2015-01-01

    (displacement or load control). The compliance based analytical formulation for G-control is explained for the DCB specimen and then applied to experimental testing of the sandwich MMB specimen. Experimental results are presented for sandwich MMB specimens with fiberglass face sheets and PVC foam core, showing...

  13. Long-term hygrothermal effects on damage tolerance of hybrid composite sandwich panels

    Science.gov (United States)

    Ishai, Ori; Hiel, Clement; Luft, Michael

    1995-01-01

    A sandwich construction, composed of hybrid carbon-glass fiber-reinforced plastic skins and a syntactic foam core, was selected as the design concept for a wind tunnel compressor blade application, where high damage tolerance and durability are of major importance. Beam specimens were prepared from open-edge and encapsulated sandwich panels which had previously been immersed in water at different temperatures for periods of up to about two years in the extreme case. Moisture absorption and strength characteristics, as related to time of exposure to hygrothermal conditions, were evaluated for the sandwich specimens and their constituents (skins and foam). After different exposure periods, low-velocity impact damage was inflicted on most sandwich specimens and damage characteristics were related to impact energy. Eventually, the residual compressive strengths of the damaged (and undamaged) beams were determined flexurally. Test results show that exposure to hygrothermal conditions leads to significant strength reductions for foam specimens and open-edge sandwich panels, compared with reference specimens stored at room temperature. In the case of skin specimens and for beams prepared from encapsulated sanwich panels that had previously been exposed to hygrothermal conditions, moisture absorption was found to improve strength as related to the reference case. The beneficial effect of moisture on skin performance was, however, limited to moisture contents below 1% (at 50 C and lower temperatures). Above this moisture level and at higher temperatures, strength degradation of the skin seems to prevail.

  14. The asymmetric sandwich theorem

    CERN Document Server

    Simons, Stephen

    2011-01-01

    We discuss the asymmetric sandwich theorem, a generalization of the Hahn-Banach theorem. As applications, we derive various results on the existence of linear functionals that include bivariate, trivariate and quadrivariate generalizations of the Fenchel duality theorem. Most of the results are about affine functions defined on convex subsets of vector spaces, rather than linear functions defined on vector spaces. We consider both results that use a simple boundedness hypothesis (as in Rockafellar's version of the Fenchel duality theorem) and also results that use Baire's theorem (as in the Robinson-Attouch-Brezis version of the Fenchel duality theorem). This paper also contains some new results about metrizable topological vector spaces that are not necessarily locally convex.

  15. Fracture of sandwiched composites

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Weh-Huei.

    1989-01-01

    Fracture of a pair of collinear cracks in various materials, such as an isotropic strip, an orthotropic strip, a bonded isotropic adhesive layer, and sandwiched orthotropic layers, is investigated. The crack surfaces are subjected to an arbitrary opening pressure p(x). The problems are formulated in terms of Fredholm integral equation of the second kind by making use the techniques of Fourier transform and finite Hilbert transform. In case of uniform opening pressure p(x)={sigma}, exact expressions for the stress intensity factors and the shape of deformed crack are obtained. Numerical calculations are carried out to study the effects of various boundary geometries and material properties on the fracture of the chosen materials.

  16. A comparative study of the impact properties of sandwich materials with different cores

    Directory of Open Access Journals (Sweden)

    Viot P.

    2012-08-01

    Full Text Available Sandwich panels are made of two high strength skins bonded to either side of a light weight core and are used in applications where high stiffness combined with low structural weight is required. The purpose of this paper is to compare the mechanical response of several sandwich panels whose core materials are different. Sandwich panels with glass fibre-reinforced polymer face sheets were used, combined with five different cores; polystyrene foam, polypropylene honeycomb, two different density Balsa wood and Cork. All specimens were subjected to low velocity impact and their structural response (Force-displacement curves were compared to quasistatic response of the panel tested using an hemispherical indenter.

  17. The Influence of Face Sheet Wrinkle Defects on the Performance of FRP Sandwich Structures

    DEFF Research Database (Denmark)

    Hayman, Brian; Berggreen, Carl Christian; Pettersson, Robert

    2005-01-01

    reported here, the influence of wrinkle defects on the in-plane compressive strength of quasiisotropic CFRP laminates used in PVC foam-cored sandwich panels has been investigated by three approaches: testing of sandwich beam specimens in fourpoint bending, testing of sandwich panels with in......Wrinkle defects may reduce the compressive strength of a face laminate for inplane loading applied perpendicularly to the line of the wrinkle. To be able to decide whether a repair is needed it is necessary to know the magnitude of the strength reduction for a given wrinkle geometry. In the studies...

  18. A comparative study of the impact properties of sandwich materials with different cores

    Science.gov (United States)

    Ramakrishnan, K. R.; Shankar, K.; Viot, P.; Guerard, S.

    2012-08-01

    Sandwich panels are made of two high strength skins bonded to either side of a light weight core and are used in applications where high stiffness combined with low structural weight is required. The purpose of this paper is to compare the mechanical response of several sandwich panels whose core materials are different. Sandwich panels with glass fibre-reinforced polymer face sheets were used, combined with five different cores; polystyrene foam, polypropylene honeycomb, two different density Balsa wood and Cork. All specimens were subjected to low velocity impact and their structural response (Force-displacement curves) were compared to quasistatic response of the panel tested using an hemispherical indenter.

  19. Structure of the cobalamin-binding protein of a putative O-demethylase from Desulfitobacterium hafniense DCB-2

    Energy Technology Data Exchange (ETDEWEB)

    Sjuts, Hanno; Dunstan, Mark S.; Fisher, Karl; Leys, David, E-mail: david.leys@manchester.ac.uk [University of Manchester, 131 Princess Street, Manchester M1 7DN (United Kingdom)

    2013-08-01

    The first crystal structure of the vitamin B12-binding protein from a three-component O-demethylase enzyme system is reported. During O-demethylation methyl groups are transferred from phenyl methyl ethers to tetrahydrofolate via methyl-B12 intermediates. This study describes the identification and the structural and spectroscopic analysis of a cobalamin-binding protein (termed CobDH) implicated in O-demethylation by the organohalide-respiring bacterium Desulfitobacterium hafniense DCB-2. The 1.5 Å resolution crystal structure of CobDH is presented in the cobalamin-bound state and reveals that the protein is composed of an N-terminal helix-bundle domain and a C-terminal Rossmann-fold domain, with the cobalamin coordinated in the base-off/His-on conformation similar to other cobalamin-binding domains that catalyse methyl-transfer reactions. EPR spectroscopy of CobDH confirms cobalamin binding and reveals the presence of a cob(III)alamin superoxide, indicating binding of oxygen to the fully oxidized cofactor. These data provide the first structural insights into the methyltransferase reactions that occur during O-demethylation by D. hafniense.

  20. RELATIONSHIP BETWEEN KNOWLEDGE, ACTION OF FAMILY IN DCB (DRAIN, CLOSE, AND BURY PROGRAM, AND THE EXISTENCE OF EGGS OF AEDES AEGYPTI MOSQUITO ON OVITRAP IN KANDAI KENDARI, INDONESIA

    Directory of Open Access Journals (Sweden)

    Reni Yunus

    2016-12-01

    Full Text Available Background: Dengue Hemorrhagic Fever (DHF is a contagious disease caused by the dengue virus infection through Aedes aegypti mosquito. DHF often causes epidemics and Extraordinary Events (EE in tropical and subtropical regions, including Indonesia. Objective: This study aims to examine the relationship between knowledge and society action on the prevention of dengue with the amount of mosquitoes trapped in ovitrap in Kandai, Kendari, Indonesia. Methods: The research method was an observational study with cross sectional design. The research was conducted at Kandai village, Kendari on May to July 2014. It was 87 homes with 87 families were recruited as sample size for this study. Ovitrap was used inside and outside of their homes. Results: DCB family knowledge and the existence of Aedes sp mosquitoes eggs on ovitrap were analyzed and observed in this study. Chi square test showed that X2 count value (1.261 was less than X2 table value (3.814 at error level 5% (α = 0.05 indicated that Ha was rejected and Ho was accepted. Meanwhile, Chi square test for the action of the family about DCB and the existence of eggs Aedes sp mosquito on ovitrap showed that X2 count value (4.115 was greater than X2 table value (3.814 at the error level 5% (α = 0.05, indicated that Ho was rejected and Ha was accepted. Conclusions:
 It was concluded that (1 there was no relationship between DCB family knowledge and the existence of Aedes sp mosquitoes eggs on ovitrap, and (2 there was a relationship between the action of family about DCB and the existence of aedes sp mosquitoes eggs on ovitrap in Kandai Kendari.

  1. Anaerobic Dehalogenation of Chloroanilines by Dehalococcoides mccartyi Strain CBDB1 and Dehalobacter Strain 14DCB1 via Different Pathways as Related to Molecular Electronic Structure.

    Science.gov (United States)

    Zhang, Shangwei; Wondrousch, Dominik; Cooper, Myriel; Zinder, Stephen H; Schüürmann, Gerrit; Adrian, Lorenz

    2017-02-24

    Dehalococcoides mccartyi strain CBDB1 and Dehalobacter strain 14DCB1 are organohalide-respiring microbes of the phyla Chloroflexi and Firmicutes, respectively. Here we report the transformation of chloroanilines by these two bacterial strains via dissimilar dehalogenation pathways, and discuss the underlying mechanism with quantum chemically calculated net atomic charges of the substrate Cl, H and C atoms. Strain CBDB1 preferentially removed Cl doubly flanked by two Cl or by one Cl and NH2, whereas strain 14DCB1 preferentially dechlorinated Cl that has an ortho H. For the CBDB1-mediated dechlorination, comparative analysis with Hirshfeld charges shows that the least negative Cl discriminates active from non-active substrates in 14 out of 15 cases, and may represent the preferred site of primary attack through cob(I)alamin. For the latter trend, 3 of 7 active substrates provide strong evidence, with partial support from 3 of the remaining 4 substrates. Regarding strain 14DCB1, the most positive carbon-attached H atom discriminates active from non-active chloroanilines in again 14 out of 15 cases. Here, regioselectivity is governed for 10 of the 11 active substrates by the most positive H attached to the highest-charge (most positive or least negative) aromatic C carrying the Cl to be removed. These findings suggest the aromatic ring H as primary site of attack through the supernucleophile Co(I), converting an initial H-bond to a full electron transfer as start of the reductive dehalogenation. For both mechanisms, one- and two-electron transfer to Cl (strain CBDB1) or H (strain 14DCB1) are compatible with the presently available data. Computational chemistry research into reaction intermediates and pathways may further add in understanding the bacterial reductive dehalogenation at the molecular level.

  2. Development of Aircraft Sandwich Parts

    Directory of Open Access Journals (Sweden)

    J. Křena

    2000-01-01

    Full Text Available The presented paper shows the design and development process of sandwich parts. A spoiler plate and a main landing gear door are developed. Sandwich parts are made of C/E composite facings and a foam core. FE models have been used for optimization of structures. Emphasis has been placed on deformations of parts under a few load cases. Experimental tests have been used for a verification of structure parts loaded by concentrated forces.

  3. CATALYTIC DECHLORINATION OF m-DCB IN WATER BY Pd/Fe%Pd/Fe双金属对水中m-二氯苯的催化脱氯

    Institute of Scientific and Technical Information of China (English)

    周红艺; 徐新华; 汪大翚

    2004-01-01

    Pd/Fe bimetallic catalysts were synthesized via chemical deposition and used to treat m-DCB.Batch experiments demonstrated that the Pd/Fe bimetallic particles could effectively dechlorinate m-DCB.The dechlorination efficiency reached 90% at a Pd/Fe loading ratio of 0.02% (mass) and metal to solution ratio 4g : 75ml in 90 min. Dechlorination was affected by several factors such as reaction temperature,pH, Pd/Fe ratio, and the induction of Pd/Fe catalysts. Chlorobenzene represents the partially stable dechlorinated intermediate in the generation of the final product (i. e. , benzene), while part of m-DCB was dechlorinated to benzene directly. The dechlorination reaction was believed to take place mainly on the active surface sites of the Pd/Fe bimetallic particles via a pseudo-first order reaction, and the activation energy of this reaction was found to be 96.6 kJ · mo1-1.

  4. Sandwich Hologram Interferometry For Determination Of Sacroiliac Joint Movements

    Science.gov (United States)

    Vukicevic, S.; Vinter, I.; Vukicevic, D.

    1983-12-01

    Investigations were carried out on embalmed and fresh specimens of human pelvisis with preserved lumbar spines, hip joints and all the ligaments. Specimens were tested under static vertical loading by pulsed laser interferometry. The deformations and behaviour of particular pelvic parts were interpreted by providing computer interferogram models. Results indicate rotation and tilting of the sacrum in the dorso-ventral direction and small but significant movements in the cranio-caudal direction. Sandwich holography proved to be the only applicable method when there is a combination of translation and tilt in the range of 200 μm to 1.5 mm.

  5. Fracture Mechanics Analysis of a Modified TSD Specimen

    DEFF Research Database (Denmark)

    Berggreen, Christian; Carlsson, Leif A.

    2008-01-01

    The Tilted Sandwich Debond (TSD) specimen has been recognized as a viable candidate for characterization of the face/core fracture resistance. Analysis, however, shows that the range of phase angles that can be realized by altering the tilt angle is quite limited. A parametric study however shows...

  6. Overall Buckling and Wringkling of Debonded Sandwich Beams: Finite Element and Experimental Results

    Directory of Open Access Journals (Sweden)

    Bambang K. Hadi

    2006-05-01

    Full Text Available Overall buckling and wrinkling of debonded sandwich beams under compressive loads were analyzed by both finite element and experimental methods. In the finite element method, a quarter and a half models of the specimens were analyzed. It shows that a quarter model is not adequate to analyze buckling of debonded sandwich beams, since it will disregard overall buckling mode that may occur in sandwich beams having compressive loads. At least a half model should be used to analyze buckling of sandwich beams. A finite element program UNA was used extensively to analyze the buckling loads. Experimental buckling of sandwich beams was carried out using a compression testing machine. Two LVDTs were used to measure deflections of the specimen during experimental loading. The loads were measured using load cells available in the machine. Specimens having core thickness of 45 and 75 mm were tested to represent overall and wrinkling modes respectively. The delamination lengths were 20, 60 and 80 mm, which represent 10, 30 and 40% of the beam length. The results show that the differences between experimental and finite element methods were less than 10%. Both overall buckling and wrinkling modes were shown in these specimens.

  7. Degradation of shear stiffness of Nomex honeycomb sandwich panel in laser irradiation

    Science.gov (United States)

    Wang, Jiawei; Jiang, Houman; Wu, Lixiong; Zhu, Yongxiang; Wei, Chenghua; Ma, Zhiliang; Wang, Lijun

    2017-05-01

    Based on the overhanging beam three-point bending method, the experimental system was set up to measure the variety of shear stiffness of Nomex honeycomb sandwich panel in laser irradiation. The shear stiffness of the specimens under different laser power density was measured. The result shows that the thermal effect during the laser irradiation leads to the degradation of mechanical properties of Nomex honeycomb sandwich panel. High temperature rise rate in the specimen is another main reason for the shear stiffness degeneration. This research provides a reference for the degradation of mechanical properties of composite materials in laser irradiation and proposes a new method for the study of laser interaction with matter.

  8. Damage Tolerance of Sandwich Plates With Debonded Face Sheets

    Science.gov (United States)

    Sankar, Bhavani V.

    2001-01-01

    A nonlinear finite element analysis was performed to simulate axial compression of sandwich beams with debonded face sheets. The load - end-shortening diagrams were generated for a variety of specimens used in a previous experimental study. The energy release rate at the crack tip was computed using the J-integral, and plotted as a function of the load. A detailed stress analysis was performed and the critical stresses in the face sheet and the core were computed. The core was also modeled as an isotropic elastic-perfectly plastic material and a nonlinear post buckling analysis was performed. A Graeco-Latin factorial plan was used to study the effects of debond length, face sheet and core thicknesses, and core density on the load carrying capacity of the sandwich composite. It has been found that a linear buckling analysis is inadequate in determining the maximum load a debonded sandwich beam can carry. A nonlinear post-buckling analysis combined with an elastoplastic model of the core is required to predict the compression behavior of debonded sandwich beams.

  9. Damage tolerance of a composite sandwich with interleaved foam core

    Science.gov (United States)

    Ishai, Ori; Hiel, Clement

    1992-01-01

    A composite sandwich panel consisting of carbon fiber-reinforced plastic (CFRP) skins and a syntactic foam core was selected as an appropriate structural concept for the design of wind tunnel compressor blades. Interleaving of the core with tough interlayers was done to prevent core cracking and to improve damage tolerance of the sandwich. Simply supported sandwich beam specimens were subjected to low-velocity drop-weight impacts as well as high velocity ballistic impacts. The performance of the interleaved core sandwich panels was characterized by localized skin damage and minor cracking of the core. Residual compressive strength (RCS) of the skin, which was derived from flexural test, shows the expected trend of decreasing with increasing size of the damage, impact energy, and velocity. In the case of skin damage, RCS values of around 50 percent of the virgin interleaved reference were obtained at the upper impact energy range. Based on the similarity between low-velocity and ballistic-impact effects, it was concluded that impact energy is the main variable controlling damage and residual strength, where as velocity plays a minor role.

  10. Urine culture - catheterized specimen

    Science.gov (United States)

    Culture - urine - catheterized specimen; Urine culture - catheterization; Catheterized urine specimen culture ... urinary tract infections may be found in the culture. This is called a contaminant. You may not ...

  11. Size Effects in Impact Damage of Composite Sandwich Panels

    Science.gov (United States)

    Dobyns, Alan; Jackson, Wade

    2003-01-01

    Panel size has a large effect on the impact response and resultant damage level of honeycomb sandwich panels. It has been observed during impact testing that panels of the same design but different panel sizes will show large differences in damage when impacted with the same impact energy. To study this effect, a test program was conducted with instrumented impact testing of three different sizes of sandwich panels to obtain data on panel response and residual damage. In concert with the test program. a closed form analysis method was developed that incorporates the effects of damage on the impact response. This analysis method will predict both the impact response and the residual damage of a simply-supported sandwich panel impacted at any position on the panel. The damage is incorporated by the use of an experimental load-indentation curve obtained for the face-sheet/honeycomb and indentor combination under study. This curve inherently includes the damage response and can be obtained quasi-statically from a rigidly-backed specimen or a specimen with any support conditions. Good correlation has been obtained between the test data and the analysis results for the maximum force and residual indentation. The predictions can be improved by using a dynamic indentation curve. Analyses have also been done using the MSC/DYTRAN finite element code.

  12. DCB - Tumor Metastasis Research

    Science.gov (United States)

    Tumor metastasis research examines the mechanisms that allow cancer cells to leave the primary tumor and spread to another part of the body. Learn about recent tumor metastasis research studies supported by the Division of Cancer Biology.

  13. Structural and failure mechanics of sandwich composites

    CERN Document Server

    Carlsson, LA; Carlsson, Leif A

    2011-01-01

    Focusing on important deformation and failure modes of sandwich structures, this volume describes the mechanics behind fracture processes. The text also reviews test methods developed for the cr, structural integrity, and failure mechanisms of sandwich structures.

  14. Interfacial Crack Arrest in Sandwich Panels with Embedded Crack Stoppers Subjected to Fatigue Loading

    Science.gov (United States)

    Martakos, G.; Andreasen, J. H.; Berggreen, C.; Thomsen, O. T.

    2017-02-01

    A novel crack arresting device has been implemented in sandwich panels and tested using a special rig to apply out-of-plane loading on the sandwich panel face-sheets. Fatigue crack propagation was induced in the face-core interface of the sandwich panels which met the crack arrester. The effect of the embedded crack arresters was evaluated in terms of the achieved enhancement of the damage tolerance of the tested sandwich panels. A finite element (FE) model of the experimental setup was used for predicting propagation rates and direction of the crack growth. The FE simulation was based on the adoption of linear fracture mechanics and a fatigue propagation law (i.e. Paris law) to predict the residual fatigue life-time and behaviour of the test specimens. Finally, a comparison between the experimental results and the numerical simulations was made to validate the numerical predictions as well as the overall performance of the crack arresters.

  15. The Influence of Face Sheet Wrinkle Defects on the Performance of FRP Sandwich Structures

    DEFF Research Database (Denmark)

    Hayman, Brian; Berggreen, Carl Christian; Pettersson, Robert

    2005-01-01

    Wrinkle defects may reduce the compressive strength of a face laminate for inplane loading applied perpendicularly to the line of the wrinkle. To be able to decide whether a repair is needed it is necessary to know the magnitude of the strength reduction for a given wrinkle geometry. In the studies...... reported here, the influence of wrinkle defects on the in-plane compressive strength of quasiisotropic CFRP laminates used in PVC foam-cored sandwich panels has been investigated by three approaches: testing of sandwich beam specimens in fourpoint bending, testing of sandwich panels with in......-plane compression, and finite element simulation. Wrinkles involving different numbers of plies have been considered. Two different sandwich lay-ups typical of deck and hull bottom panels in a naval ship have been included....

  16. The Effect of Face Sheet Wrinkle Defects on the Strength of FRP Sandwich Structures

    DEFF Research Database (Denmark)

    Hayman, Brian; Berggreen, Christian; Pettersson, Robert

    2007-01-01

    Wrinkle defects may reduce the compressive strength of a face laminate for in-plane loading applied perpendicularly to the line of the wrinkle. To be able to decide whether a repair is needed, it is necessary to know the magnitude of the strength reduction for a given wrinkle geometry....... In the studies reported here, the influence of wrinkle defects on the in-plane compressive strength of quasi-isotropic carbon fiber reinforced plastic (CFRP) laminates used in PVC foam-cored sandwich panels has been investigated by three approaches: testing of sandwich beam specimens in four-point bending......, testing of sandwich panels with inplane compression, and finite element simulation. Wrinkles involving different numbers of plies have been considered. Two different sandwich lay-ups typical of deck and hull bottom panels in naval ships have been included....

  17. Effect of varying geometrical parameters of trapezoidal corrugated-core sandwich structure

    Directory of Open Access Journals (Sweden)

    Zaid N.Z.M.

    2017-01-01

    Full Text Available Sandwich structure is an attractive alternative that increasingly used in the transportation and aerospace industry. Corrugated-core with trapezoidal shape allows enhancing the damage resistance to the sandwich structure, but on the other hand, it changes the structural response of the sandwich structure. The aim of this paper is to study the effect of varying geometrical parameters of trapezoidal corrugated-core sandwich structure under compression loading. The corrugated-core specimen was fabricated using press technique, following the shape of trapezoidal shape. Two different materials were used in the study, glass fibre reinforced plastic (GFRP and carbon fibre reinforced plastic (CFRP. The result shows that the mechanical properties of the core in compression loading are sensitive to the variation of a number of unit cells and the core thickness.

  18. Interfacial Crack Arrest in Sandwich Panels with Embedded Crack Stoppers Subjected to Fatigue Loading

    Science.gov (United States)

    Martakos, G.; Andreasen, J. H.; Berggreen, C.; Thomsen, O. T.

    2016-08-01

    A novel crack arresting device has been implemented in sandwich panels and tested using a special rig to apply out-of-plane loading on the sandwich panel face-sheets. Fatigue crack propagation was induced in the face-core interface of the sandwich panels which met the crack arrester. The effect of the embedded crack arresters was evaluated in terms of the achieved enhancement of the damage tolerance of the tested sandwich panels. A finite element (FE) model of the experimental setup was used for predicting propagation rates and direction of the crack growth. The FE simulation was based on the adoption of linear fracture mechanics and a fatigue propagation law (i.e. Paris law) to predict the residual fatigue life-time and behaviour of the test specimens. Finally, a comparison between the experimental results and the numerical simulations was made to validate the numerical predictions as well as the overall performance of the crack arresters.

  19. Technology sandwich panels with mineral wool insulation

    OpenAIRE

    Tyulenev M.; Burtzeva M.; Mednikova E.

    2016-01-01

    Sandwich panel — self–supporting structure consisting of metal cladding and thermal insulation core. As a heat–insulating core used mineral wool, foamed plastics. Production of sandwich panels with insulation mineral wool performed on modular lines for the production of aggregate or conveyer scheme. Sandwich panels are used as load–bearing elements of the facades, as well as a roof covering.

  20. Non-linear Behavior of Curved Sandwich Panels

    DEFF Research Database (Denmark)

    Berggreen, Carl Christian; Jolma, P.; Karjalainen, J. P.;

    2003-01-01

    In this paper the non-linear behavior of curved sandwich panels is investigated both numerically and experimentally. Focus is on various aspects of finite element modeling and calculation procedures. A simply supported, singly curved, CFRP/PVC sandwich panel is analyzed under uniform pressure load...... and results are compared to test data. A novel test arrangement utilizing a water filled cushion to create the uniform pressure load on curved panel specimen is used to obtain the experimental data. The panel is modeled with three different commercial finite element codes. Two implicit and one explicit code...... are used with various element types, modeling approaches and material models. The results show that the theoretical and experimental methods generally show fair agreement in panel non-linear behavior before collapse. It is also shown that special attention to detail has to be taken, because the predicted...

  1. Wire and Packing Tape Sandwiches

    Science.gov (United States)

    Rabinowitz, Sandy

    2009-01-01

    In this article, the author describes how students can combine craft wire with clear packing tape to create a two-dimensional design that can be bent and twisted to create a three-dimensional form. Students sandwich wire designs between two layers of tape. (Contains 1 online resource.)

  2. Thermal-Diode Sandwich Panel

    Science.gov (United States)

    Basiulis, A.

    1986-01-01

    Thermal diode sandwich panel transfers heat in one direction, but when heat load reversed, switches off and acts as thermal insulator. Proposed to control temperature in spacecraft and in supersonic missiles to protect internal electronics. In combination with conventional heat pipes, used in solar panels and other heat-sensitive systems.

  3. High temperature structural sandwich panels

    Science.gov (United States)

    Papakonstantinou, Christos G.

    High strength composites are being used for making lightweight structural panels that are being employed in aerospace, naval and automotive structures. Recently, there is renewed interest in use of these panels. The major problem of most commercial available sandwich panels is the fire resistance. A recently developed inorganic matrix is investigated for use in cases where fire and high temperature resistance are necessary. The focus of this dissertation is the development of a fireproof composite structural system. Sandwich panels made with polysialate matrices have an excellent potential for use in applications where exposure to high temperatures or fire is a concern. Commercial available sandwich panels will soften and lose nearly all of their compressive strength temperatures lower than 400°C. This dissertation consists of the state of the art, the experimental investigation and the analytical modeling. The state of the art covers the performance of existing high temperature composites, sandwich panels and reinforced concrete beams strengthened with Fiber Reinforced Polymers (FRP). The experimental part consists of four major components: (i) Development of a fireproof syntactic foam with maximum specific strength, (ii) Development of a lightweight syntactic foam based on polystyrene spheres, (iii) Development of the composite system for the skins. The variables are the skin thickness, modulus of elasticity of skin and high temperature resistance, and (iv) Experimental evaluation of the flexural behavior of sandwich panels. Analytical modeling consists of a model for the flexural behavior of lightweight sandwich panels, and a model for deflection calculations of reinforced concrete beams strengthened with FRP subjected to fatigue loading. The experimental and analytical results show that sandwich panels made with polysialate matrices and ceramic spheres do not lose their load bearing capability during severe fire exposure, where temperatures reach several

  4. Self-healing sandwich structures incorporating an interfacial layer with vascular network

    Science.gov (United States)

    Chen, Chunlin; Peters, Kara; Li, Yulong

    2013-02-01

    A self-healing capability specifically targeted for sandwich composite laminates based on interfacial layers with built-in vascular networks is presented. The self-healing occurs at the facesheet-core interface through an additional interfacial layer to seal facesheet cracks and rebond facesheet-core regions. The efficacy of introducing the self-healing system at the facesheet-core interface is evaluated through four-point bend and edgewise compression testing of representative foam core sandwich composite specimens with impact induced damage. The self-healing interfacial layer partially restored the specific initial stiffness, doubling the residual initial stiffness as compared to the control specimen after the impact event. The restoration of the ultimate specific skin strength was less successful. The results also highlight the critical challenge in self-healing of sandwich composites, which is to rebond facesheets which have separated from the core material.

  5. Moisture absorption and mechanical degradation studies of PMI foam cored fiber/epoxy resin sandwich composites

    Directory of Open Access Journals (Sweden)

    Liang Yin

    2015-04-01

    Full Text Available The present paper explores the result of hygrothermic aging of polymethacrylimide (PMI foam core sandwich composites immersed in different temperature deionized (DI and sea waters. The prepared specimens were tested for moisture up-take behavior and the resulting property degradation in terms of flexural and flat wise compressive strength. The results indicate that the saturated hygroscopic time of specimens immersed in low temperature water and high temperature water is about 480h and 720h, respectively. Due to the presence of ionic in sea water, the specimens immersed in sea water have higher compressive and flexural strength than specimens immersed in DI water.

  6. Flexural Behavior of Aluminum Honeycomb Core Sandwich Structure

    Science.gov (United States)

    Matta, Vidyasagar; Kumar, J. Suresh; Venkataraviteja, Duddu; Reddy, Guggulla Bharath Kumar

    2017-05-01

    and has more strength. By the power press used as forming method we fabricate the honey comb core and stacking the sheets with adhesive as epoxy resin or laser beam welding and sandwich structure will form with two face sheets. Then the specimen is taken to be tested to know the flexural behaviour by the flexural test as 3 point and 4 pont bend test. After testing of two different tests then we get the force vs displacement curve by this we can know the maximum force and by loading configurations and its displacement or deflection then we can calculate flexural stiffness and core shear modulus by the variation of three parameters. Our ultimate aim is to achieve maximum strength by minimum weight.

  7. Characterizing Facesheet/Core Disbonding in Honeycomb Core Sandwich Structure

    Science.gov (United States)

    Rinker, Martin; Ratcliffe, James G.; Adams, Daniel O.; Krueger, Ronald

    2013-01-01

    Results are presented from an experimental investigation into facesheet core disbonding in carbon fiber reinforced plastic/Nomex honeycomb sandwich structures using a Single Cantilever Beam test. Specimens with three, six and twelve-ply facesheets were tested. Specimens with different honeycomb cores consisting of four different cell sizes were also tested, in addition to specimens with three different widths. Three different data reduction methods were employed for computing apparent fracture toughness values from the test data, namely an area method, a compliance calibration technique and a modified beam theory method. The compliance calibration and modified beam theory approaches yielded comparable apparent fracture toughness values, which were generally lower than those computed using the area method. Disbonding in the three-ply facesheet specimens took place at the facesheet/core interface and yielded the lowest apparent fracture toughness values. Disbonding in the six and twelve-ply facesheet specimens took place within the core, near to the facesheet/core interface. Specimen width was not found to have a significant effect on apparent fracture toughness. The amount of scatter in the apparent fracture toughness data was found to increase with honeycomb core cell size.

  8. Mechanical properties characterization of composite sandwich materials intended for space antenna applications

    Science.gov (United States)

    Bowles, Kenneth J.; Vannucci, Raymond D.

    1986-01-01

    The composite materials proposed for use in the Advanced Communications Technology Satellite (ACTS) Program contains a new, high modulus graphite fiber as the reinforcement. A study was conducted to measure certain mechanical properties of the new fiber-reinforced material as well as of a composite-faced aluminum honeycomb sandwich structure. Properties were measured at -157, 22, and 121 C. Complete characterization of this material was not intended. Longitudinal tensile, picture-frame shear, short-beam shear, and flexural tests were performed on specimens of the composite face-sheet materials. Unidirectional, cross-plied, and quasi-isotropic fiber composite ply layup designs were fabricated and tested. These designs had been studied by using NASA's Integrated Composite Analyzer (ICAN) computer program. Flexural tests were conducted on (+/- 60/0 deg) sub s composite-faced sandwich structure material. Resistance strain gages were used to measure strains in the tensile, picture-frame, and sandwich flexural tests. The sandwich flexural strength was limited by the core strength at -157 and 22 C. The adhesive bond strength was the limiting factor at 121 C. Adhesive mechanical properties are reflected in sandwich structure flexural properties when the span-to-depth ratio is great enough to allow a significant shear effect on the load-deflection behavior of the sandwich beam. Most measured properties agreed satisfactorily with the properties predicted by ICAN.

  9. Fatigue characterization of Poly Vinyl Chloride (PVC) foam core sandwich composite using the G-control method

    DEFF Research Database (Denmark)

    Manca, Marcello; Berggreen, Christian; Carlsson, Leif A.

    2016-01-01

    This paper presents experimental results from cyclic crack propagation tests performed on sandwich specimens with glass/epoxy face sheets and Poly Vinyl Chloride (PVC) foam cores using the G-controlled cyclic energy release rate (ΔG) test procedure. The face material was tested in tension......, compression and shear to determine in-plane and out-of-plane mechanical properties, such as Young’s modulus, Poisson’s ratio and shear modulus. These properties were then used in an analytical model of the mixed-mode bending sandwich specimen to calculate compliance and energy release rate. Finite element...... analysis was used to determine the mode-mixity of the crack loading. Experimental crack growth cyclic tests were carried out on pre-cracked mixed-mode bending sandwich specimens with H45, H100 and H160 PVC foam cores under two mode-mixities (mode I and mode II dominant). Post-mortem analysis was performed...

  10. Determination of a cohesive law for delamination modelling - Accounting for variation in crack opening and stress state across the test specimen width

    DEFF Research Database (Denmark)

    Joki, R. K.; Grytten, F.; Hayman, Brian

    2016-01-01

    -scale bridging and the multi-axial state of stress in the test specimen. The fracture resistance is calculated from the applied moments, the elastic material properties and the geometry of the test specimen. The cohesive law is then determined in a three step procedure: 1) Obtain the bridging law...... that the changing state of stress and deformation across the width of the test specimen is taken into account. The changing state of stress and deformation across the specimen width is shown to be significant for small openings (small fracture process zone size). This will also be important for the initial part......The cohesive law for Mode I delamination in glass fibre Non-Crimped Fabric reinforced vinylester is determined for use in finite element models. The cohesive law is derived from a delamination test based on DCB specimens loaded with pure bending moments taking into account the presence of large...

  11. A Damage Tolerance Comparison of Composite Hat-Stiffened and Honeycomb Sandwich Structure for Launch Vehicle Interstage Applications

    Science.gov (United States)

    Nettles, A. T.

    2011-01-01

    In this study, a direct comparison of the compression-after-impact (CAI) strength of impact-damaged, hat-stiffened and honeycomb sandwich structure for launch vehicle use was made. The specimens used consisted of small substructure designed to carry a line load of approx..3,000 lb/in. Damage was inflicted upon the specimens via drop weight impact. Infrared thermography was used to examine the extent of planar damage in the specimens. The specimens were prepared for compression testing to obtain residual compression strength versus damage severity curves. Results show that when weight of the structure is factored in, both types of structure had about the same CAI strength for a given damage level. The main difference was that the hat-stiffened specimens exhibited a multiphase failure whereas the honeycomb sandwich structure failed catastrophically.

  12. Composite Sandwich Technologies Lighten Components

    Science.gov (United States)

    2010-01-01

    Leveraging its private resources with several Small Business Innovation Research (SBIR) contracts with both NASA and the U.S. Department of Defense, WebCore Technologies LLC, of Miamisburg, Ohio, developed a fiber-reinforced foam sandwich panel it calls TYCOR that can be used for a wide variety of industrial and consumer applications. Testing at Glenn Research Center?s Ballistic Impact Facility demonstrated that the technology was able to exhibit excellent damage localization and stiffness during impact. The patented and trademarked material has found use in many demanding applications, including marine, ground transportation, mobile shelters, bridges, and most notably, wind turbines.

  13. On the use of a woven mat to control the crack path in composite sandwich structures

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Berggreen, Christian; Carlsson, Leif A.

    2008-01-01

    is separation of face and core (debonding). Debonds can arise as a result of defects from production when an area between face and core has not been primed sufficiently resulting in a lack of adhesion. In use, impact loading, e.g. due to collision with objects, can result in formation of a debond crack....... Whether or not kinking occurs is governed by the stress state at the crack tip, e.g. described by the mode-mixity of the complex stress intensity factor and the properties of the face, core and adhesive [3]. The criticality of an existing crack can be highly dependent on the crack propagation path, since...... cantilever beam specimen loaded by unequal bending moments (DCB-UBM specimen) [6, 7], see Figure 2. The specimen is loaded by a roller-wire system mounted in a tensile test machine. The ratio between the two applied moments (M1/M2) is dictated by the ratio between roller distances (I1/I2), see Figure 2...

  14. 37 CFR 2.59 - Filing substitute specimen(s).

    Science.gov (United States)

    2010-07-01

    ... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Filing substitute specimen(s..., DEPARTMENT OF COMMERCE RULES OF PRACTICE IN TRADEMARK CASES Drawing § 2.59 Filing substitute specimen(s). (a... specimen(s), the applicant must: (1) For an amendment to allege use under § 2.76, verify by affidavit...

  15. Compressive and bending behavior of sandwich panels with Octet truss core fabricated from wires

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Ji Hyun; Nah, Seong Jun; Kang, Ki Ju [Chonnam National Univ., Gwangju (Korea, Republic of); Koo, Man Hoe [Agency for Defense Development, Daejeon (Korea, Republic of)

    2005-03-01

    Ultra light metal structures have been studied for several years because of their superior specific stiffness, strength and potential of multi functions. Many studies have been focused on how to manufacture ultra light metal structures and optimize them. In this study, we introduced a new idea to make sandwich panels having Octet truss cores. Wires bent in a shape of triangular wave were assembled to construct an Octet truss core and it was bonded with two face sheets to be a sandwich panel. The bending and compressive strength and stiffness were estimated through elementary mechanics for the sandwich specimens with two kinds of face sheets and the results were compared with the ones measured by experiments. Some aspects of assembling and mechanical behavior were discussed compared with Kagome core fabricated from wire, which had been introduced in the authors' previous work.

  16. Standard Terminology of Structural Sandwich Constructions

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2007-01-01

    1.1 This terminology covers terms necessary for a basic uniform understanding and usage of the language peculiar to structural sandwich constructions. The simplest structural sandwich is a three layered construction formed by bonding a thin layer (facing) to each side of a thick layer (core).

  17. Study of Debond Fracture Toughness of Sandwich Composites with Metal Foam Core

    Institute of Scientific and Technical Information of China (English)

    Xinzhu Wang; Linzhi Wu; Shixun Wang

    2009-01-01

    Two types of experiments were designed and performed to evaluate the adhesive bond in metal foam composite sandwich structures. The tensile bond strength of face/core was determined through the flatwise tensile test (FWT). The test results show that the interfacial peel strength is lower than the interlaminar peel strength in FWT test. The mode I interfacial fracture toughness (GIC) of sandwich structures containing a pre-crack on the upper face/core interface is determined by modified cracked sandwich beam (MCSB) experiment. It is found that the crack propagates unsynchronously on the two side of the specimen and the propagation of interfacial debonding always stays on the face/core interface during the MCSB tests. In order to simulate the failure of metal foam composite sandwich structures, a computational model based on the Tsai-Hill failure criterion and cohesive zone model is used. By comparing with experiment results, it can be concluded that the computational model can validly simulate the interfacial failure of metal foam composite sandwich structures with reasonable accuracy.

  18. Controlled Environment Specimen Transfer

    DEFF Research Database (Denmark)

    Damsgaard, Christian Danvad; Zandbergen, Henny W.; Hansen, Thomas Willum

    2014-01-01

    Specimen transfer under controlled environment conditions, such as temperature, pressure, and gas composition, is necessary to conduct successive complementary in situ characterization of materials sensitive to ambient conditions. The in situ transfer concept is introduced by linking an environme...

  19. Experimental Study On Fracture Property Of Double Cantilever Beam Specimen With Aluminum Foam

    Directory of Open Access Journals (Sweden)

    Kim Y.C.

    2015-06-01

    Full Text Available This study aims to investigate double cantilever beam specimen with aluminum foam bonded by spray adhesive to investigate the fracture strength of the adhesive joint experimentally. The fracture energy at opening mode is calculated by the formulae of British Engineering Standard (BS 7991 and International Standard (ISO 11343. For the static experiment, four types of specimens with the heights (h of 25 mm, 30 mm, 35 mm and 40 mm are manufactured and the experimental results are compared with each other. As the height becomes greater, the fracture energy becomes higher. After the length of crack reaches 150 mm, the fracture energy of the specimen (h=35 mm is greater than that of the specimen (h=40 mm. Fatigue test is also performed with DCB test specimen. As the height decreases, the fracture energy becomes higher. By the result obtained from this study, aluminum foam with adhesive joint can be applied to actual composite structure and its fracture property can possibly be anticipated.

  20. New "sandwich" structures conformed from three dimensional

    Directory of Open Access Journals (Sweden)

    Alba, Juan J.

    1996-03-01

    Full Text Available Poor interlaminar properties as well as poor-skin-to-core adhesion properties are very often the common existing problems we find when designing with "sandwich" structures. A new type of 3D-fabric "sandwich" structure is being developed in order to avoid these problems. Although the manufacturing process is very simple, a very complex "sandwich" structure is obtained as a result of the complexity of the 3D-fabric used. This 3D-fabric is a 3D woven glass fabric produced on velvet weaving machines with glass yarns. It is an integrally woven "sandwich" laminate for all kinds of composite products. The strength of the vertical fibers makes, that also after impregnation with a resin matrix, the "sandwich" structure is maintained. The result is a laminate with high strength and stiffness and low weight. On each side of this "sandwich" laminate additional reinforcement materials can be laminated and a synthetic foam can be injected in the hollow structure. This will allow to establish the mechanical properties of a finished product.

    Las pobres propiedades, tanto interlaminares como de adhesión entre piel y núcleo, constituyen uno de los grandes problemas cuando se diseñan estructuras utilizando paneles tipo "sandwich". Un nuevo tipo de panel "sandwich", configurado a partir de tejidos tridimensionales, está siendo desarrollado en la actualidad con el objetivo de eliminar esos problemas. Aunque el proceso de fabricación es muy simple, el panel "sandwich" obtenido es de estructura compleja, como resultado de la complejidad del tejido tridimensional utilizado. Este tejido tridimensional (3D es un tejido de fibra de vidrio producido en máquinas de tejer especializadas. La resistencia de las fibras verticales hace que, después de la impregnación con una resina, se mantenga la configuración tipo "sandwich". El resultado es un laminado de alta resistencia, gran rigidez y bajo peso. Sobre cada uno de los lados del panel "sandwich" se pueden

  1. New "sandwich" structures conformed from three dimensional

    OpenAIRE

    1996-01-01

    Poor interlaminar properties as well as poor-skin-to-core adhesion properties are very often the common existing problems we find when designing with "sandwich" structures. A new type of 3D-fabric "sandwich" structure is being developed in order to avoid these problems. Although the manufacturing process is very simple, a very complex "sandwich" structure is obtained as a result of the complexity of the 3D-fabric used. This 3D-fabric is a 3D woven glass fabric produced on velvet weaving machi...

  2. Tensile Properties and Failure Mechanism of 3D Woven Hollow Integrated Sandwich Composites

    Science.gov (United States)

    Liu, Chang; Cai, Deng'an; Zhou, Guangming; Lu, Fangzhou

    2017-01-01

    Tensile properties and failure mechanism of 3D woven hollow integrated sandwich composites are investigated experimentally, theoretically and numerically in this paper. Firstly, the tensile properties are obtained by quasi-static tensile tests on the specimens in two principal directions of the sandwich panels, called warp and weft. The experimental results shows that the tensile performances of the warp are better than that of the weft. By observing the broken specimens, it is found that the touch parts between yarns are the main failure regions under tension. Then, a theoretical method is developed to predict the tensile properties. By comparing with the experimental data, the accuracy of the theoretical method is verified. Simultaneously, a finite element model is established to predict the tensile behavior of the composites. The numerical results agree well with the experimental data. Moreover, the simulated progressive damages show that the contact regions in the warp and weft tension are both the initial failure areas.

  3. Detecting and identifying damage in sandwich polymer composite by using acoustic emission

    Energy Technology Data Exchange (ETDEWEB)

    McGugan, M.; Soerensen, Bent F.; Oestergaard, R.; Bech, T.

    2006-12-15

    Acoustic emission is a useful monitoring tool for extracting extra information during mechanical testing of polymer composite sandwich materials. The study of fracture mechanics within test specimens extracted from wind turbine blade material is presented. The contribution of the acoustic emission monitoring technique in defining different failure modes identified during the testing is discussed. The development of in-situ structural monitoring and control systems is considered. (au)

  4. A J integral based method to measure fracture resistance and cohesive laws in materials exhibiting large scale plasticity

    DEFF Research Database (Denmark)

    Sørensen, Bent F.; Goutianos, Stergios

    2014-01-01

    A method is developed to extract the fracture resistance and mode I cohesive law of nonlinear elastic-plastic materials using a Double Cantilever Beam (DCB) sandwich specimen loaded with pure bending moments. The method is based on the J integral which is valid for materials having a non-linear s......A method is developed to extract the fracture resistance and mode I cohesive law of nonlinear elastic-plastic materials using a Double Cantilever Beam (DCB) sandwich specimen loaded with pure bending moments. The method is based on the J integral which is valid for materials having a non...

  5. Buckling driven debonding in sandwich columns

    DEFF Research Database (Denmark)

    Østergaard, Rasmus Christian

    2008-01-01

    A compression loaded sandwich column that contains a debond is analyzed using a geometrically non-linear finite element model. The model includes a cohesive zone along one face sheet/core interface whereby the debond can extend by interface crack growth. Two geometrical imperfections are introduced......; a global imperfection of the sandwich column axis and a local imperfection of the debonded face sheet axis. The model predicts the sandwich column to be very sensitive to the initial debond length and the local face sheet imperfection. The study shows that the sensitivity to the face sheet imperfection...... results from two mechanisms: (a) interaction of local debond buckling and global buckling and (b) the development of a damaged zone at the debond crack tip. Based on the pronounced imperfection sensitivity, the author predicts that an experimental measurement of the strength of sandwich structures may...

  6. Local slamming impact of sandwich composite hulls

    National Research Council Canada - National Science Library

    Qin, Z; Batra, R.C

    2009-01-01

    We develop a hydroelastic model based on a {3,2}-order sandwich composite panel theory and Wagner's water impact theory for investigating the fluid-structure interaction during the slamming process...

  7. Active structural health monitoring of composite plates and sandwiches

    Directory of Open Access Journals (Sweden)

    Sadílek P.

    2013-12-01

    Full Text Available The aim of presented work is to design, assemble and test a functional system, that is able to reveal damage from impact loading. This is done by monitoring of change of spectral characteristics on a damaged structure that is caused by change of mechanical properties of material or by change of structure’s geometry. Excitation and monitoring of structures was done using piezoelectric patches. Unidirectional composite plate was tested for eigenfrequencies using chirp signal. The eigenfrequencies were compared to results from experiments with an impact hammer and consequently with results from finite element method. Same method of finding eigenfrequencies was used on a different unidirectional composite specimen. Series of impacts were performed. Spectrum of eigenfrequencies was measured on undamaged plate and then after each impact. Measurements of the plate with different level of damage were compared. Following experiments were performed on sandwich materials where more different failures may happen. Set of sandwich beams (cut out from one plate made of two outer composite layers and a foam core was investigated and subjected to several impacts. Several samples were impacted in the same manner to get comparable results. The impacts were performed with growing impact energy.

  8. On the Milnor fibers of sandwiched singularities

    OpenAIRE

    Nemethi, Andras; Popescu-Pampu, Patrick

    2009-01-01

    The sandwiched surface singularities are those rational surface singularities which dominate birationally smooth surface singularities. de Jong and van Straten showed that one can reduce the study of the deformations of a sandwiched surface singularity to the study of deformations of a 1-dimensional object, a so-called decorated plane curve singularity. In particular, the Milnor fibers corresponding to their various smoothing components may be reconstructed up to diffeomorphisms from those de...

  9. Investigation of failure mechanisms in GFRP sandwich structures with face sheet wrinkle defects used for wind turbine blades

    DEFF Research Database (Denmark)

    Leong, Martin Klitgaard; Overgaard, Lars C. T.; Thomsen, Ole Thybo

    2012-01-01

    Wrinkle defects can be formed during the production of wind turbine blades consisting of composite monolithic and sandwich laminates. Earlier studies have shown that the in-plane compressive strength of a sandwich panel with wrinkle defects may decrease dramatically. This study focuses on the fai......Wrinkle defects can be formed during the production of wind turbine blades consisting of composite monolithic and sandwich laminates. Earlier studies have shown that the in-plane compressive strength of a sandwich panel with wrinkle defects may decrease dramatically. This study focuses...... on the failure modes of sandwich specimens consisting of thick GFRP face sheets with a wrinkle defect and a balsa wood core subjected to in-plane compression loading. Three distinct modes of failure were found, and the strain distributions leading up to these failures were established by use of digital image...... correlation (DIC). Finite element analyses were subsequently conducted to model the response of the test specimens prior to failure, and generally a very good agreement was found with the DIC measurements, although slight differences between the predicted and measured strain fields were observed in the local...

  10. Preparation, characterization and catalytic behavior of hierachically porous CuO/α-Fe2O3/SiO2 composite material for CO and o-DCB oxidation

    Institute of Scientific and Technical Information of China (English)

    Xiaodong Ma; Xi Feng; Xuan He; Hongwen Guo; Lu Lü

    2011-01-01

    Hierachically porous (HP) CuO/α-Fe2O3/SiO2 composite material was fabricated by sol-gel method and multi-hydrothermal processes using HP-SiO2 as support.The resulting material was characterized by N2 adsorption-desorption,X-ray diffraction and scanning electron microscopy.The as-prepared CuO/Fe2O3/HP-SiO2 sample,with α-Fe2O3 and CuO nanocrystals,possessed a co-continuous skeleton,through-macroporous and mesoporous structure.Its catalytic behavior for CO and o-DCB oxidation was investigated.The result showed that CuO/Fe2O3/HP-SiO2 catalyst exhibited high catalytic activity for both CO and o-DCB oxidation,indicating its potential application in combined abatement of CO and chlorinated volatile organic compounds.

  11. Structural performance of new thin-walled concrete sandwich panel system reinforced with bfrp shear connectors

    DEFF Research Database (Denmark)

    Hodicky, Kamil; Hulin, Thomas; Schmidt, Jacob Wittrup

    2013-01-01

    This paper presents a new thin-walled concrete sandwich panel system reinforced with basalt fiber-reinforced plastic (BFRP) with optimum structural performances and a high thermal resistance developed by Connovate and Technical University of Denmark. The shear connecting system made of a BFRP grid...... is described and provides information on the structural design with its advantages. Experimental and numerical investigations of the BFRP connecting systems were performed. The experimental program included testing of small scale specimens by applying shear (push-off) loading and semi-full scale specimens...

  12. Standard Test Method for Laboratory Aging of Sandwich Constructions

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1999-01-01

    1.1 This test method covers the determination of the resistance of sandwich panels to severe exposure conditions as measured by the change in selected properties of the material after exposure. The exposure cycle to which the specimen is subjected is an arbitrary test having no correlation with natural weathering conditions. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  13. Predicting The Compression Strength Of Impact-Damaged Sandwich Panels

    Science.gov (United States)

    Ratcliffe, James; Jackson, Wade; Schaff, Jeffery

    1990-01-01

    The objective of this work was to develop a technique for predicting the residual compression strength of sandwich panels containing impact damage in one facesheet. The technique was tailored to predict the strength of specimens that exhibit a failure mode involving the formation of kink bands at locations of peak strain in the region of impact damage. Under continued compression loading, the kink bands propagate in a stable manner perpendicular to the applied load. When a critical kink-band length is reached, growth becomes unstable corresponding to panel failure. The analysis follows in two sections. The first section calculates the far-field stress required for stable kink-band growth and the second calculates that required for unstable growth. The residual strength prediction is made when the stress for stable growth becomes equal to that for unstable kink-band growth. Initial comparisons between analysis and experiment show good agreement.

  14. Genomics and museum specimens.

    Science.gov (United States)

    Nachman, Michael W

    2013-12-01

    Nearly 25 years ago, Allan Wilson and colleagues isolated DNA sequences from museum specimens of kangaroo rats (Dipodomys panamintinus) and compared these sequences with those from freshly collected animals (Thomas et al. 1990). The museum specimens had been collected up to 78 years earlier, so the two samples provided a direct temporal comparison of patterns of genetic variation. This was not the first time DNA sequences had been isolated from preserved material, but it was the first time it had been carried out with a population sample. Population geneticists often try to make inferences about the influence of historical processes such as selection, drift, mutation and migration on patterns of genetic variation in the present. The work of Wilson and colleagues was important in part because it suggested a way in which population geneticists could actually study genetic change in natural populations through time, much the same way that experimentalists can do with artificial populations in the laboratory. Indeed, the work of Thomas et al. (1990) spawned dozens of studies in which museum specimens were used to compare historical and present-day genetic diversity (reviewed in Wandeler et al. 2007). All of these studies, however, were limited by the same fundamental problem: old DNA is degraded into short fragments. As a consequence, these studies mostly involved PCR amplification of short templates, usually short stretches of mitochondrial DNA or microsatellites. In this issue, Bi et al. (2013) report a breakthrough that should open the door to studies of genomic variation in museum specimens. They used target enrichment (exon capture) and next-generation (Illumina) sequencing to compare patterns of genetic variation in historic and present-day population samples of alpine chipmunks (Tamias alpinus) (Fig. 1). The historic samples came from specimens collected in 1915, so the temporal span of this comparison is nearly 100 years.

  15. Biaxial Creep Specimen Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    JL Bump; RF Luther

    2006-02-09

    This report documents the results of the weld development and abbreviated weld qualification efforts performed by Pacific Northwest National Laboratory (PNNL) for refractory metal and superalloy biaxial creep specimens. Biaxial creep specimens were to be assembled, electron beam welded, laser-seal welded, and pressurized at PNNL for both in-pile (JOYO reactor, O-arai, Japan) and out-of-pile creep testing. The objective of this test campaign was to evaluate the creep behavior of primary cladding and structural alloys under consideration for the Prometheus space reactor. PNNL successfully developed electron beam weld parameters for six of these materials prior to the termination of the Naval Reactors program effort to deliver a space reactor for Project Prometheus. These materials were FS-85, ASTAR-811C, T-111, Alloy 617, Haynes 230, and Nirnonic PE16. Early termination of the NR space program precluded the development of laser welding parameters for post-pressurization seal weldments.

  16. [Blood Count Specimen].

    Science.gov (United States)

    Tamura, Takako

    2015-12-01

    The circulating blood volume accounts for 8% of the body weight, of which 45% comprises cellular components (blood cells) and 55% liquid components. We can measure the number and morphological features of blood cells (leukocytes, red blood cells, platelets), or count the amount of hemoglobin in a complete blood count: (CBC). Blood counts are often used to detect inflammatory diseases such as infection, anemia, a bleeding tendency, and abnormal cell screening of blood disease. This count is widely used as a basic data item of health examination. In recent years, clinical tests before consultation have become common among outpatient clinics, and the influence of laboratory values on consultation has grown. CBC, which is intended to count the number of raw cells and to check morphological features, is easily influenced by the environment, techniques, etc., during specimen collection procedures and transportation. Therefore, special attention is necessary to read laboratory data. Providing correct test values that accurately reflect a patient's condition from the laboratory to clinical side is crucial. Inappropriate medical treatment caused by erroneous values resulting from altered specimens should be avoided. In order to provide correct test values, the daily management of devices is a matter of course, and comprehending data variables and positively providing information to the clinical side are important. In this chapter, concerning sampling collection, blood collection tubes, dealing with specimens, transportation, and storage, I will discuss their effects on CBC, along with management or handling methods.

  17. Behavior of sandwich panels subjected to bending fatigue, axial compression loading and in-plane bending

    Science.gov (United States)

    Mathieson, Haley Aaron

    This thesis investigates experimentally and analytically the structural performance of sandwich panels composed of glass fibre reinforced polymer (GFRP) skins and a soft polyurethane foam core, with or without thin GFRP ribs connecting skins. The study includes three main components: (a) out-of-plane bending fatigue, (b) axial compression loading, and (c) in-plane bending of sandwich beams. Fatigue studies included 28 specimens and looked into establishing service life (S-N) curves of sandwich panels without ribs, governed by soft core shear failure and also ribbed panels governed by failure at the rib-skin junction. Additionally, the study compared fatigue life curves of sandwich panels loaded under fully reversed bending conditions (R=-1) with panels cyclically loaded in one direction only (R=0) and established the stiffness degradation characteristics throughout their fatigue life. Mathematical models expressing fatigue life and stiffness degradation curves were calibrated and expanded forms for various loading ratios were developed. Approximate fatigue thresholds of 37% and 23% were determined for non-ribbed panels loaded at R=0 and -1, respectively. Digital imaging techniques showed significant shear contribution significantly (90%) to deflections if no ribs used. Axial loading work included 51 specimens and examined the behavior of panels of various lengths (slenderness ratios), skin thicknesses, and also panels of similar length with various rib configurations. Observed failure modes governing were global buckling, skin wrinkling or skin crushing. In-plane bending involved testing 18 sandwich beams of various shear span-to-depth ratios and skin thicknesses, which failed by skin wrinkling at the compression side. The analytical modeling components of axially loaded panels include; a simple design-oriented analytical failure model and a robust non-linear model capable of predicting the full load-displacement response of axially loaded slender sandwich panels

  18. Energy Dissipation in Sandwich Structures During Axial Compression

    DEFF Research Database (Denmark)

    Urban, Jesper

    2002-01-01

    The purpose of this paper is to investigate the energy dissipation in sandwich structures during axial crushing. Axial crushing tests on six sandwich elements are described. The sandwich elements consist of a polyurethane core and E-glass/Polyester skin. The elements compare to full-scale structu......The purpose of this paper is to investigate the energy dissipation in sandwich structures during axial crushing. Axial crushing tests on six sandwich elements are described. The sandwich elements consist of a polyurethane core and E-glass/Polyester skin. The elements compare to full...

  19. A multifunctional heat pipe sandwich panel structure

    Energy Technology Data Exchange (ETDEWEB)

    Queheillalt, Douglas T.; Wadley, Haydn N.G. [University of Virginia, Department of Materials Science and Engineering, 140 Chemistry Way, P.O. Box 400745, Charlottesville, VA 22904 (United States); Carbajal, Gerardo [University of Turabo, School of Engineering, P.O. Box 3030, Gurabo 00778 (Puerto Rico); Peterson, G.P. [University of Colorado at Boulder, 914 Broadway, Boulder, CO 80309 (United States)

    2008-01-15

    A multifunctional sandwich panel combining efficient structural load support and thermal management characteristics has been designed and experimentally assessed. The concept is based upon a truncated, square honeycomb sandwich structure. In closed cell honeycomb structures, the transport of heat from one face to the other occurs by a combination of conduction through the webs and convection/radiation within the cells. Here, much more effective heat transport is achieved by multifunctionally utilizing the core as a heat pipe sandwich panel. Its interior consists of a 6061 aluminum truncated-square honeycomb core covered with a stochastic open-cell nickel foam wick. An electroless nickel plating barrier layer inhibited the chemical reaction between the deionized water working fluid and the aluminum structure, retarding the generation of non-condensable hydrogen gas. A thermodynamic model was used to guide the design of the heat pipe sandwich panel. We describe the results of a series of experiments that validate the operational principle of the multifunctional heat pipe sandwich panel and characterize its transient response to an intense localized heat source. The systems measured thermal response to a localized heat source agrees well with that predicted by a finite difference method model used to predict the thermal response. (author)

  20. Ultra-Lightweight Nanocomposite Foams and Sandwich Structures for Space Structure Applications

    Science.gov (United States)

    Tan, Seng

    2012-01-01

    Microcellular nanocomposite foams and sandwich structures have been created to have excellent electrical conductivity and radiation-resistant properties using a new method that does not involve or release any toxicity. The nanocomposite structures have been scaled up in size to 12 X 12 in. (30 X 30 cm) for components fabrication. These sandwich materials were fabricated mainly from PE, CNF, and carbon fibers. Test results indicate that they have very good compression and compression-after-impact properties, excellent electrical conductivity, and superior space environment durability. Compression tests show that 1000 ESH (equivalent Sun hours) of UV exposure has no effect on the structural properties of the sandwich structures. The structures are considerably lighter than aluminum alloy (= 36 percent lighter), which translates to 36 percent weight savings of the electronic enclosure and its housing. The good mechanical properties of the materials may enable the electronic housing to be fabricated with a thinner structure that further reduces the weight. There was no difficulty in machining the sandwich specimens into electronic enclosure housing.

  1. Fracture Behaviours in Compression-loaded Triangular Corrugated Core Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Zaid N.Z.M.

    2016-01-01

    Full Text Available The failure modes occurring in sandwich panels based on the corrugations of aluminium alloy, carbon fibre-reinforced plastic (CFRP and glass fibre-reinforced plastic (GFRP are analysed in this work. The fracture behaviour of these sandwich panels under compressive stresses is determined through a series of uniform lateral compression performed on samples with different cell wall thicknesses. Compression test on the corrugated-core sandwich panels were conducted using an Instron series 4505 testing machine. The post-failure examinations of the corrugated-core in different cell wall thickness were conducted using optical microscope. Load-displacement graphs of aluminium alloy, GFRP and CFRP specimens were plotted to show progressive damage development with five unit cells. Four modes of failure were described in the results: buckling, hinges, delamination and debonding. Each of these failure modes may dominate under different cell wall thickness or loading condition, and they may act in combination. The results indicate that thicker composites corrugated-core panels tend can recover more stress and retain more stiffness. This analysis provides a valuable insight into the mechanical behaviour of corrugated-core sandwich panels for use in lightweight engineering applications.

  2. Specimen Holder For Flammability Tests

    Science.gov (United States)

    Rucker, Michelle A.

    1992-01-01

    Fixture holds sheet specimens for flammability tests. Frame and clamps designed to minimize local overstress on specimen. Heat capacity of fixture low, interfering less with interpretation of results of test by drawing less heat away from specimen. Accepts films, fabrics, foams, and other sheets, rigid or flexible. Specimens thin or thick, or of variable thickness. Bent to accommodate curved rigid specimens. Also used for such other tests as particle-impact tests.

  3. Evaluation of Composite Honeycomb Sandwich Panels Under Compressive Loads at Elevated Temperatures

    Science.gov (United States)

    Walker, Sandra P.

    1998-01-01

    Fourteen composite honeycomb sandwich panels were tested to failure under compressive loading. The test specimens included panels with both 8 and 24-ply graphite-bismaleimide composite facesheets and both titanium and graphite-polyimide core materials. The panels were designed to have the load introduced through fasteners attached to pairs of steel angles on the ends of the panels to simulate double shear splice joints. The unloaded edges were unconstrained. Test temperatures included room temperature, 250F, and 300F. For the room and 250F temperature tests, the 24-ply specimen failure strains were close to the unnotched allowable strain values and failure loads were well above the design loads. However, failure strains much lower than the unnotched allowable strain values, and failure loads below the design loads were observed with several of the 8-ply specimens. For each individual test temperature, large variations in the failure strains and loads were observed for the 8-ply specimens. Dramatic decreases in the failure strains and loads were observed for the 24-ply specimens as the test temperature was increased from 250F to 300F. All 8-ply specimens appeared to have failed in a facesheet strength failure mode for all test temperatures. The 24-ply specimens displayed appreciably greater amounts of bending prior to failure than the 8-ply specimens, and panel buckling occurred prior to facesheet strength failure for the 24-ply room and 250F temperature tests.

  4. NASA Biological Specimen Repository

    Science.gov (United States)

    McMonigal, K. A.; Pietrzyk, R. A.; Sams, C. F.; Johnson, M. A.

    2010-01-01

    The NASA Biological Specimen Repository (NBSR) was established in 2006 to collect, process, preserve and distribute spaceflight-related biological specimens from long duration ISS astronauts. This repository provides unique opportunities to study longitudinal changes in human physiology spanning may missions. The NBSR collects blood and urine samples from all participating ISS crewmembers who have provided informed consent. These biological samples are collected once before flight, during flight scheduled on flight days 15, 30, 60, 120 and within 2 weeks of landing. Postflight sessions are conducted 3 and 30 days after landing. The number of in-flight sessions is dependent on the duration of the mission. Specimens are maintained under optimal storage conditions in a manner that will maximize their integrity and viability for future research The repository operates under the authority of the NASA/JSC Committee for the Protection of Human Subjects to support scientific discovery that contributes to our fundamental knowledge in the area of human physiological changes and adaptation to a microgravity environment. The NBSR will institute guidelines for the solicitation, review and sample distribution process through establishment of the NBSR Advisory Board. The Advisory Board will be composed of representatives of all participating space agencies to evaluate each request from investigators for use of the samples. This process will be consistent with ethical principles, protection of crewmember confidentiality, prevailing laws and regulations, intellectual property policies, and consent form language. Operations supporting the NBSR are scheduled to continue until the end of U.S. presence on the ISS. Sample distribution is proposed to begin with selections on investigations beginning in 2017. The availability of the NBSR will contribute to the body of knowledge about the diverse factors of spaceflight on human physiology.

  5. Modelling of Specimen Fracture

    Science.gov (United States)

    2013-09-23

    the plate center. An end load of 1.0 MPa was applied. 1 2 3 Modelling of Specimen Fracture – Final Report 11 TR-13-47 Figure 2.5: Crack Geometry Figure...Christopher Bayley DRDC Atlantic Dockyard Laboratory Pacific CFB Esquimalt, Building 199 PO Box 17000, Station Forces Victoria, British Columbia Canada...q The weighting function, q , can be any arbitrary function within the J-integral domain, and must be zero on the domain boundary . An easy function

  6. Labeling of Patient Specimens

    Science.gov (United States)

    2011-01-26

    noted during the event that the actu.al number of near miss incidmts reported monthly was low due to laboratory personnel performing rounds each...specimens never leaves label and if moved it is labeled), All orders in system and all near misses and errors reported to patient safety Purchase/Install...Meeting 14 Aug 09, 1400 in lab break room thru out Develop TICK sheet to track near misses .JDI Ms. Clark Clinics will provide toPS 1st working day of

  7. Vibro-acoustics of lightweight sandwich structures

    CERN Document Server

    Lu, Tianjian

    2014-01-01

    Vibro-Acoustics of Lightweight Sandwich Structures introduces the study of the coupled vibration and acoustic behavior of lightweight sandwich structures in response to harmonic force and sound pressure. This book focuses on the theoretical modeling and experimental investigation of lightweight sandwich structures in order to provide a predictive framework for vibro-acoustic characteristics of typical engineering structures. Furthermore, by developing solution tools, it concentrates on the influence of key systematic parameters leading to effective guidance for optimal structure design toward lightweight, high-stiffness and superior sound insulation capability. This book is intended for researchers, scientists, engineers and graduate students in mechanical engineering especially in structural mechanics, mechanics and acoustics. Fengxian Xin and Tianjian Lu both work at the School of Aerospace, Xi’an Jiaotong University.

  8. Novel 1-D Sandwich Photonic Bandgap Structure

    Institute of Scientific and Technical Information of China (English)

    庞云波; 高葆新

    2004-01-01

    A sandwich photonic bandgap (PBG) structure is a novel PBG structure whose periodic lattice is buried in the middle of a substrate. Neither drilling nor suspending the substrate is required, and the integrity of the ground plane is maintained. This paper presents several modification techniques for sandwich PBG structure fabrication. The forbidden gap can be improved by adopting the chirping technique, applying the tapering technique, enlarging the periodic elements, adjusting the location of the periodic lattice in the substrate, and using different dielectric media H-shape elements. A finite difference time domain method is applied to analyze the structures. Deep and wide stopbands can be obtained using the modified sandwich structures. Experimental measurement results agree well with the theoretical analysis.

  9. Behaviour of Metal Foam Sandwich Panels

    DEFF Research Database (Denmark)

    2011-01-01

    Sandwich panels as used in structures comprise of a foam core enclosed by thin high strength steel faces. This paper discusses currently design formulae of local buckling behaviour of such panels using the finite element method. Multiple wave finite element models were adopted to investigate...... and examine the adequacy of currently used approach for the design of sandwich panels. The paper presents brief details of the finite element model used including geometry, load pattern and boundary conditions. The selected model gives good agreement with experimental results from Pokharel and Mahendran (2003......). The study shows that currently available design formulae are conservative for stocky sandwich plate elements while being over-conservative for high slenderness. A unified design formula of local buckling behaviour applicable to the full range of slenderness is developed....

  10. AA, sandwich line with magnetic horn

    CERN Multimedia

    1980-01-01

    The magnetic horn, focusing the antiprotons emanating from the target, was affixed to a sandwich line through which the 150 kA pulses were supplied. Expecting to have to change from time to time the fragile horn (inner conductor only 0.7 mm thick), the assembly was designed for quick exchange. At the lower end of the sandwich line we see the connectors for the high-current cables, at the upper end the magnet horn. It has just been lifted from the V-supports which held it aligned downstream of the target. Continue with 8010293.

  11. Hyperglucagonaemia analysed by glucagon sandwich ELISA

    DEFF Research Database (Denmark)

    Albrechtsen, Nicolai Jacob Wewer; Hartmann, Bolette; Veedfald, Simon

    2014-01-01

    characterised. The specific determination of fully processed, intact glucagon requires a 'sandwich' assay employing a combination of antibodies directed against both N- and C-termini. We compared a novel assay for intact glucagon with a highly sensitive C-terminal RIA (hitherto considered specific) to determine...... the extent to which the hyperglucagonaemia measured in clinical samples was caused by authentic glucagon. METHODS: We examined the performance of three commercial glucagon 'sandwich' ELISAs. The ELISA with the best overall performance was selected to compare glucagon measurements in clinical samples...

  12. Nonlinear dynamic analysis of sandwich panels

    Science.gov (United States)

    Lush, A. M.

    1984-01-01

    Two analytical techniques applicable to large deflection dynamic response calculations for pressure loaded composite sandwich panels are demonstrated. One technique utilizes finite element modeling with a single equivalent layer representing the face sheets and core. The other technique utilizes the modal analysis computer code DEPROP which was recently modified to include transverse shear deformation in a core layer. The example problem consists of a simply supported rectangular sandwich panel. Included are comparisons of linear and nonlinear static response calculations, in addition to dynamic response calculations.

  13. OPTIMAL DESIGN OF QUADRATIC SANDWICH PLATE

    Directory of Open Access Journals (Sweden)

    TIMAR Dr. Imre

    2016-05-01

    Full Text Available In this paper, we show the optimal design of the three-layered sandwich plates. The objective function contains the material and fabrication costs. The design constraints are the maximal stresses, the deflection of plates and damping of vibrations. The unknown is the thickness of the filling foam. By the mathematical method, we define the minima of the cost function and the optimal thickness of the filling layer of foam. The active constraint is the deflection, so we calculate of the costs of the sandwich plate with the homogeneous plate.

  14. New examples of sandwich gravitational waves and their impulsive limit

    CERN Document Server

    Podolsky, J

    1998-01-01

    Non-standard sandwich gravitational waves are constructed from the homogeneous pp vacuum solution and the motions of free test particles in the space-times are calculated explicitly. They demonstrate the caustic property of sandwich waves. By performing limits to impulsive gravitational wave it is demonstrated that the resulting particle motions are identical regardless of the ''initial'' sandwich.

  15. Non-linear analytical solutions for laterally loaded sandwich plates

    DEFF Research Database (Denmark)

    Riber, Hans Jørgen

    1997-01-01

    This work focuses on the response of orthotropic sandwich composite plates with large deflections due to high lateral loads. The results have special application to the design of ship structures. A geometrical nonlinear theory is outlined, on the basis of the classical sandwich plate theory...... of sandwich plates subjected to high lateral loading. (C) 1997 Published by Elsevier Science Ltd. All rights reserved....

  16. Experimental investigations of sandwich panels using high performance concrete thin plates exposed to fire

    DEFF Research Database (Denmark)

    Hulin, Thomas; Hodicky, Kamil; Schmidt, Jacob Wittrup

    2015-01-01

    temperatures for panels with 30 mm thick plates stiffened by structural ribs, thick insulation layers, and steel shear connecting systems. Parametric variation assessing the role of each component of the sandwich structure was performed on unloaded specimens of reduced size. Full size walls were tested......Structural sandwich panels using thin high performance concrete (HPC) plates offer a possibility to address the modern environmental challenges faced by the construction industry. Fire resistance is a major necessity in structures using HPC. This paper presents experimental studies at elevated...... plate and one of them experienced heavy heat-induced spalling. Results highlighted insulation shear failure from differential thermal expansion at the interface with concrete. It suggests the existence of a high bond level between the two materials which might allow structural applications at early age...

  17. Analysis of the Flexure Behavior and Compressive Strength of Fly Ash Core Sandwiched Composite Material

    Directory of Open Access Journals (Sweden)

    Vijaykumar H.K

    2014-07-01

    Full Text Available In this paper, commercially available Fly Ash and Epoxy is used for the core material, woven glass fabric as reinforcing skin material, epoxy as matrix/adhesive materials used in this study for the construction of sandwich composite. Analysis is carried out on different proportions of epoxy and fly ash sandwiched composite material for determining the flexural strength and compressive strength, three different proportions of epoxy and fly ash used for the study. Those are 65%-35% (65% by weight fly ash and 35% by weight epoxy resin composite material, 60%-40% and 55%-45% composite material. 60%-40% composite material specimen shows better results in the entire test carried out i.e. Flexure and Compression. The complete experimental results are discussed and presented in this paper.

  18. A Finite Element Analysis for Predicting the Residual Compressive Strength of Impact-Damaged Sandwich Panels

    Science.gov (United States)

    Ratcliffe, James G.; Jackson, Wade C.

    2008-01-01

    A simple analysis method has been developed for predicting the residual compressive strength of impact-damaged sandwich panels. The method is tailored for honeycomb core-based sandwich specimens that exhibit an indentation growth failure mode under axial compressive loading, which is driven largely by the crushing behavior of the core material. The analysis method is in the form of a finite element model, where the impact-damaged facesheet is represented using shell elements and the core material is represented using spring elements, aligned in the thickness direction of the core. The nonlinear crush response of the core material used in the analysis is based on data from flatwise compression tests. A comparison with a previous analysis method and some experimental data shows good agreement with results from this new approach.

  19. A Finite Element Analysis for Predicting the Residual Compression Strength of Impact-Damaged Sandwich Panels

    Science.gov (United States)

    Ratcliffe, James G.; Jackson, Wade C.

    2008-01-01

    A simple analysis method has been developed for predicting the residual compression strength of impact-damaged sandwich panels. The method is tailored for honeycomb core-based sandwich specimens that exhibit an indentation growth failure mode under axial compression loading, which is driven largely by the crushing behavior of the core material. The analysis method is in the form of a finite element model, where the impact-damaged facesheet is represented using shell elements and the core material is represented using spring elements, aligned in the thickness direction of the core. The nonlinear crush response of the core material used in the analysis is based on data from flatwise compression tests. A comparison with a previous analysis method and some experimental data shows good agreement with results from this new approach.

  20. AA, sandwich line with magnetic horn

    CERN Document Server

    1980-01-01

    Continuation from 8010293: Finally, the sandwich line with the horn is placed on the ground, for the horn to be inspected and, if needed, exchanged for a new one. The whole procedure was trained with several members of the AA team, for quick and safe handling, and to share the radiation dose amongst them.

  1. Proof of the Thin Sandwich Conjecture

    CERN Document Server

    Bartnik, R; Bartnik, Robert; Fodor, Gyula

    1993-01-01

    We prove that the Thin Sandwich Conjecture in general relativity is valid, provided that the data $(g_{ab},\\dot g_{ab})$ satisfy certain geometric conditions. These conditions define an open set in the class of possible data, but are not generically satisfied. The implications for the ``superspace'' picture of the Einstein evolution equations are discussed.

  2. Behaviour of Metal Foam Sandwich Panels

    DEFF Research Database (Denmark)

    2011-01-01

    Sandwich panels as used in structures comprise of a foam core enclosed by thin high strength steel faces. This paper discusses currently design formulae of local buckling behaviour of such panels using the finite element method. Multiple wave finite element models were adopted to investigate...

  3. Structural detailing of openings in sandwich panels

    NARCIS (Netherlands)

    Tomà, T.; Courage, W.

    1996-01-01

    European Recommendations exist which provide calculation rules to determine the strength and stiffness of sandwich panels composed of two metal faces with a foam in between. In case of openings in such panels (e.g. for windows) an influence will appear with regard to the stiffness and loadbearing ca

  4. X-joints in composite sandwich panels

    NARCIS (Netherlands)

    Vredeveldt, A.W.; Janssen, G.Th.M.

    1998-01-01

    The small structural weight of fast large ships such as fast mono hulls or catamaran type of ships is of extreme importance to their success. One possible light weight structural solution is the sandwich panel with fibre reinforced laminates and a balsa, honeycomb or foam core. A severe obstacle for

  5. Organometallic half-sandwich iridium anticancer complexes

    NARCIS (Netherlands)

    Liu, Z.; Habtemariam, A.; Pizarro, A.M.; Fletcher, S.A.; Kisova, A.; Vrana, O.; Salassa, L.; Bruijnincx, P.C.A.|info:eu-repo/dai/nl/33799529X; Clarkson, G.J.; Brabec, V.; Sadler, Peter J.

    2011-01-01

    The low-spin 5d6 IrIII organometallic half-sandwich complexes [(η5-Cpx)Ir(XY)Cl]0/+, Cpx = Cp*, tetramethyl(phenyl)cyclopentadienyl (Cpxph), or tetramethyl(biphenyl)cyclopentadienyl (Cpxbiph), XY = 1,10-phenanthroline (4−6), 2,2′-bipyridine (7−9), ethylenediamine (10 and 11), or picolinate (12−14),

  6. Feedback Sandwiches Affect Perceptions but Not Performance

    Science.gov (United States)

    Parkes, Jay; Abercrombie, Sara; McCarty, Teresita

    2013-01-01

    The feedback sandwich technique-make positive comments; provide critique; end with positive comments-is commonly recommended to feedback givers despite scant evidence of its efficacy. These two studies (N = 20; N = 350) of written peer feedback with third-year medical students on clinical patient note-writing assignments indicate that students…

  7. X-joints in composite sandwich panels

    NARCIS (Netherlands)

    Vredeveldt, A.W.; Janssen, G.Th.M.

    1998-01-01

    The small structural weight of fast large ships such as fast mono hulls or catamaran type of ships is of extreme importance to their success. One possible light weight structural solution is the sandwich panel with fibre reinforced laminates and a balsa, honeycomb or foam core. A severe obstacle for

  8. Compression After Impact on Honeycomb Core Sandwich Panels with Thin Facesheets, Part 2: Analysis

    Science.gov (United States)

    Mcquigg, Thomas D.; Kapania, Rakesh K.; Scotti, Stephen J.; Walker, Sandra P.

    2012-01-01

    A two part research study has been completed on the topic of compression after impact (CAI) of thin facesheet honeycomb core sandwich panels. The research has focused on both experiments and analysis in an effort to establish and validate a new understanding of the damage tolerance of these materials. Part 2, the subject of the current paper, is focused on the analysis, which corresponds to the CAI testings described in Part 1. Of interest, are sandwich panels, with aerospace applications, which consist of very thin, woven S2-fiberglass (with MTM45-1 epoxy) facesheets adhered to a Nomex honeycomb core. Two sets of materials, which were identical with the exception of the density of the honeycomb core, were tested in Part 1. The results highlighted the need for analysis methods which taken into account multiple failure modes. A finite element model (FEM) is developed here, in Part 2. A commercial implementation of the Multicontinuum Failure Theory (MCT) for progressive failure analysis (PFA) in composite laminates, Helius:MCT, is included in this model. The inclusion of PFA in the present model provided a new, unique ability to account for multiple failure modes. In addition, significant impact damage detail is included in the model. A sensitivity study, used to assess the effect of each damage parameter on overall analysis results, is included in an appendix. Analysis results are compared to the experimental results for each of the 32 CAI sandwich panel specimens tested to failure. The failure of each specimen is predicted using the high-fidelity, physicsbased analysis model developed here, and the results highlight key improvements in the understanding of honeycomb core sandwich panel CAI failure. Finally, a parametric study highlights the strength benefits compared to mass penalty for various core densities.

  9. Type specimen studies in Pleurotus

    NARCIS (Netherlands)

    Petersen, Ronald H.; Krisai-Greilhuber, Irmgard

    1999-01-01

    An epitype specimen is designated for Pleurotus cornucopiae. Morphological examination of Mexican material and the type specimen of P. opuntiae showed that the distribution of this species includes North Africa and the highlands of Mexico. The type specimen of Lentinus (Pleurotus) eugrammus reveals

  10. Formation Mechanism of by-Product PCBs in the P-DCB Production%对二氯苯生产中的多氯联苯副产物排放与生成机制研究

    Institute of Scientific and Technical Information of China (English)

    李素梅; 朱琦; 刘平; 尚屹; 田亚静; 姚薇; 朱维耀

    2009-01-01

    A typical p-DCB production process was selected in this study. A series of p-DCB product samples, 1 Japanese sample and 1 chlorobenzene sample were collected and analyzed for by-product polychlorinated biphenyls (PCBs). It is a common phenomenon that byproduct PCBs exists in the p-DCB production process. The PCBs levels in the p-DCB samples were 62-781 ng/g and the highest WHO-TEQ in the process was 0.24 ng/g, while the PCBs level in the Japanese sample reached 881 ng/g. PCB31 was the dominate PCB congener in all the p-DCB samples with the maximum 98.5% of the total PCBs. Maximum content of PCBs was TrCBs in the p-DCB samples with the next TeCBs, DiCBs and PeCBs, while MoCBs were the highest in the chlorobenzene sample. Furthermore, a formation mechanism of PCBs in the production process was proposed and proved by the analysis result. It suggested that the formation of PCBs form the condensation of polychlorobenzenes had a relation with the concentration of polychlorobenzenes and the chlorine position in the benzene ring.%对国内某化工企业一系列对二氯苯样品和日本某企业对二氯苯样品的PCBs副产物的含量和生成机制进行了研究.在该企业对二氯苯样品检测到了62~781 ng/g的PCBs,WHO-TEQ最高达到了0.24 pg/g,在日本样品中PCBs总量也达到了881 ng/g,说明PCBs副产物在对二氯苯生产中是一个比较普遍的现象.在对二氯苯样品中,PCB31是主要的PCBs单体,最高占到了PCBs总量的98.5%.对二氯苯样品中都是TrCBs含量最高,其次是TeCBs和DiCBs以及PeCBs;而氯苯样品中则是MoCBs含量最高,占到了PCBs总量的73.5%.本研究还对各主要PCBs化合物的生成机制进行了探索,发现多氯苯缩合生成PCBs的过程受到多氯苯的浓度和氯对苯环的定位影响,并得到了试验的证实.

  11. HYBRID-SANDWICHED REINFORCEMENT WITH GEOSYNTHETICS

    Science.gov (United States)

    Yasuhara, Kazuya; Yamazaki, Shinji; Sakakibara, Tsutomu

    Advantageous aspects of sandwich-type reinforced earth structures combined with geosynthetics and sand mat are highlighted in this paper. Those aspects were elucidated by two kinds of laboratory tests : (1) large consolidation tests for improvement of hydraulic conductivity and (2) model footing tests on improvement of bearing capacity and deformation characteristics for reinforced earth structures, including both vertical permeability and horizontal transmissibility characteristics of geosynthetics results from both laboratory tests indicated the following: i) Hydraulic conductivity of geosynthetics used for this type of earth reinforcement can be maintained for a long period. Such conductivity sometimes disappears, particularly because of clogging when geosynthetics are adopted in embankment construction using fine-grained soils. This fact indicates that the sand mats which are laid above and beneath geosynthetics play a salient role in preventing clogging of geosynthetics that occurs by intrusion of fines from cohesive soils. ii) Sandwich-type reinforcement combined with geosynthetics and sand mats increases stability and decreases deformation of earth structures. In particular, the sandwich structure is effective for providing toughness, which has remained an important issue for reducing infrastructural maintenance and costs. In the later part of the paper, conventionally available stability analysis was carried out to propose the design procedure for reinforced earth structures and at the same time numerical analysis was also conducted to ensure the applicability of the hybrid-sandwiched earth reinforcement newly proposed in the current paper. Finally, based on the horizontal placement by means of HBS described in the current paper, the vertical drain procedure using the sandwich structures for accelerating consolidation and increasing stability of soft soils is also suggested for the future research and investigation.

  12. Structural Analysis of Sandwich Foam Panels

    Energy Technology Data Exchange (ETDEWEB)

    Kosny, Jan [ORNL; Huo, X. Sharon [Tennessee Technological University

    2010-04-01

    The Sandwich Panel Technologies including Structural Insulated Panels (SIPs) can be used to replace the conventional wooden-frame construction method. The main purpose of this Cooperative Research and Development Agreement (CRADA) between UT-Battelle, LLC and SGI Venture, Inc. was to design a novel high R-value type of metal sandwich panelized technology. This CRADA project report presents design concept discussion and numerical analysis results from thermal performance study of this new building envelope system. The main objective of this work was to develop a basic concept of a new generation of wall panel technologies which will have R-value over R-20 will use thermal mass to improve energy performance in cooling dominated climates and will be 100% termite resistant. The main advantages of using sandwich panels are as follows: (1) better energy saving structural panels with high and uniform overall wall R-value across the elevation that could not be achieved in traditional walls; and (2) reducing the use of raw materials or need for virgin lumber. For better utilization of these Sandwich panels, engineers need to have a thorough understanding of the actual performance of the panels and system. Detailed analysis and study on the capacities and deformation of individual panels and its assembly have to be performed to achieve that goal. The major project activity was to conduct structural analysis of the stresses, strains, load capacities, and deformations of individual sandwich components under various load cases. The analysis simulated the actual loading conditions of the regular residential building and used actual material properties of the steel facings and foam.

  13. Fatigue Failure of Sandwich Beams with Wrinkle Defects Used for Wind Turbine Blades

    DEFF Research Database (Denmark)

    Leong, Martin Klitgaard; Hvejsel, C.F.; Lund, Erik

    2012-01-01

    Glass fiber face sheet/balsa wood core sandwich beams with out-of-plane fiber misalignments/wrinkle defects were subjected to in-plane fully reversed fatigue loading and the failure modes were documented. A fatigue life design limit was estimated using finite element analyses and the Northwestern...... University failure theory. The presence of the wrinkle defect significantly lowered the fatigue strength, but it was found that the test specimens could reach a pre-defined fatigue life with no signs of damage, by applying a fatigue load below 80% of the estimated design limit....

  14. On the Milnor fibers of sandwiched singularities

    CERN Document Server

    Nemethi, Andras

    2009-01-01

    The sandwiched surface singularities are those rational surface singularities which dominate birationally smooth surface singularities. de Jong and van Straten showed that one can reduce the study of the deformations of a sandwiched surface singularity to the study of deformations of a 1-dimensional object, a so-called decorated plane curve singularity. In particular, the Milnor fibers corresponding to their various smoothing components may be reconstructed up to diffeomorphisms from those deformations of associated decorated curves which have only ordinary singularities. Part of the topology of such a deformation is encoded in the incidence matrix between the irreducible components of the deformed curve and the points which decorate it, well-defined up to permutations of columns. Extending a previous theorem ofours, which treated the case of cyclic quotient singularities, we show that the Milnor fibers which correspond to deformations whose incidence matrices are different up to permutations of columns are n...

  15. Utilization of Bamboo as Lightweight Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Suthon SRIVARO

    2016-05-01

    Full Text Available Lightweight sandwich panels consisting of bamboo faces and oil palm trunk core were manufactured using melamine urea formaldehyde with the resin content of 250 g/m2 (solid basis. The parameters examined were node and density of bamboo faces. Physical (board density, thickness swelling and water absorption and mechanical (modulus of elasticity and modulus of rupture properties of the sandwich board obtained were investigated and compared with other bamboo products and commercial wood based products. Result showed that this panel had better dimensional stability than those of other bamboo products but lower bending strength. Node of bamboo had no significant effect on any board properties examined. Most of board properties were influenced by bamboo face density. Comparing the properties to commercial wood based products, this panel could be used as wall/floor applications.

  16. Ultrasonic Spectroscopy of Stainless Steel Sandwich Panels

    Science.gov (United States)

    Cosgriff, Laura M.; Lerch, Bradley A.; Hebsur, Mohan G.; Baaklini, George Y.; Ghosn, Louis J.

    2003-01-01

    Enhanced, lightweight material systems, such as 17-4PH stainless steel sandwich panels are being developed for use as fan blades and fan containment material systems for next generation engines. In order to improve the production for these systems, nondestructive evaluation (NDE) techniques, such as ultrasonic spectroscopy, are being utilized to evaluate the brazing quality between the 17-4PH stainless steel face plates and the 17-4PH stainless steel foam core. Based on NDE data, shear tests are performed on sections representing various levels of brazing quality from an initial batch of these sandwich structures. Metallographic characterization of brazing is done to corroborate NDE findings and the observed shear failure mechanisms.

  17. Buckling optimisation of sandwich cylindrical panels

    Science.gov (United States)

    Abouhamzeh, M.; Sadighi, M.

    2016-06-01

    In this paper, the buckling load optimisation is performed on sandwich cylindrical panels. A finite element program is developed in MATLAB to solve the governing differential equations of the global buckling of the structure. In order to find the optimal solution, the genetic algorithm Toolbox in MATLAB is implemented. Verifications are made for both the buckling finite element code and also the results from the genetic algorithm by comparisons to the results available in literature. Sandwich cylindrical panels are optimised for the buckling strength with isotropic or orthotropic cores with different boundary conditions. Results are presented in terms of stacking sequence of fibers in the face sheets and core to face sheet thickness ratio.

  18. Utilization of Bamboo as Lightweight Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Suthon SRIVARO

    2016-05-01

    Full Text Available Lightweight sandwich panels consisting of bamboo faces and oil palm trunk core were manufactured using melamine urea formaldehyde with the resin content of 250 g/m2 (solid basis. The parameters examined were node and density of bamboo faces. Physical (board density, thickness swelling and water absorption and mechanical (modulus of elasticity and modulus of rupture properties of the sandwich board obtained were investigated and compared with other bamboo products and commercial wood based products. Result showed that this panel had better dimensional stability than those of other bamboo products but lower bending strength. Node of bamboo had no significant effect on any board properties examined. Most of board properties were influenced by bamboo face density. Comparing the properties to commercial wood based products, this panel could be used as wall/floor applications.

  19. A spiral antenna sandwiched by dielectric layers

    OpenAIRE

    Nakano, Hisamatsu; Ikeda, Masakazu; Hitosugi, Kazuo; Yamauchi, Junji

    2004-01-01

    An infinitesimally thin spiral antenna, sandwiched by bottom and top dielectric layers having the same relative permittivity, is analyzed under the condition that the dielectric layers are of finite extent and the antenna is backed by an infinite conducting plane. As the thickness of the top dielectric layer increases, the input impedance and axial ratio (AR) vary in an oscillatory fashion, with a period slightly larger than one-half of the guided wavelength of a wave propagating in an unboun...

  20. Mixed auxeticity of auxetic sandwich structures

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Teik-Cheng [SIM University, Singapore (Singapore)

    2012-07-15

    Previously, a sandwich structure in which the Poisson ratios of the core and facesheets possess opposite signs has been shown to exhibit overall conventional and auxetic behavior depending on the loading mode - axial loading or bending - for an intermediate range of relative core thickness. In addition to these two loading modes, sandwich structures in aerospace applications encounter torsional loads. In this paper, the effective Poisson's ratio for torsional loading is proposed. Results show that, depending on the loading mode and the relative core thickness, there can be up to four levels of overall auxeticity, namely (i) full auxeticity (FA) if the structure behaves as an auxetic structure under all three modes of loading, (ii) high auxeticity (HA) if the structure behaves as an auxetic structure in two of the loading modes, (iii) low auxeticity (LA) if the structure behaves as an auxetic structure in only one of the loading modes, and (iv) no auxeticity (NA) if the structure behaves as a conventional structure under all of the three loading modes. These results indicate that by selecting the Poisson's ratios and the thickness of the cores and facesheets, the sandwich structure can be made to respond differently under different external loading conditions. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  1. Data characterizing compressive properties of Al/Al2O3 syntactic foam core metal matrix sandwich

    Directory of Open Access Journals (Sweden)

    Mohammed Yaseer Omar

    2015-12-01

    Full Text Available Microstructural observations and compressive property datasets of metal matrix syntactic foam core sandwich composite at quasi-static and high strain rate (HSR conditions (525–845 s−1 are provided. The data supplied in this article includes sample preparation procedure prior to scanning electron and optical microscopy as well as the micrographs. The data used to construct the stress–strain curves and the derived compressive properties of all specimens in both quasi-static and HSR regions are included. Videos of quasi-static compressive failure and that obtained by a high speed image acquisition system during deformation and failure of HSR specimen are also included.

  2. Shear Behavior of 3D Woven Hollow Integrated Sandwich Composites: Experimental, Theoretical and Numerical Study

    Science.gov (United States)

    Zhou, Guangming; Liu, Chang; Cai, Deng'an; Li, Wenlong; Wang, Xiaopei

    2016-11-01

    An experimental, theoretical and numerical investigation on the shear behavior of 3D woven hollow integrated sandwich composites was presented in this paper. The microstructure of the composites was studied, then the shear modulus and load-deflection curves were obtained by double lap shear tests on the specimens in two principal directions of the sandwich panels, called warp and weft. The experimental results showed that the shear modulus of the warp was higher than that of the weft and the failure occurred in the roots of piles. A finite element model was established to predict the shear behavior of the composites. The simulated results agreed well with the experimental data. Simultaneously, a theoretical method was developed to predict the shear modulus. By comparing with the experimental data, the accuracy of the theoretical method was verified. The influence of structural parameters on shear modulus was also discussed. The higher yarn number, yarn density and dip angle of the piles could all improve the shear modulus of 3D woven hollow integrated sandwich composites at different levels, while the increasing height would decrease the shear modulus.

  3. On the Rigidity in Bending of a Sandwich with Thick CFRP Facings and Thin Soft Core

    Science.gov (United States)

    Caprino, G.; Iaccarino, P.; Langella, A.; Lamboglia, A.

    2009-06-01

    Flexure tests in three-point bending were performed in the elastic domain on sandwich specimens whose facings were made of T800H/3900-2 laminates, and the core by a soft rubbery layer. The contribution of the shear and flexural deformations to the overall deflection was varied by varying the slenderness ratio. The rigidities yielded by the load-displacement curve were corrected for the indentation occurring at the points of load introduction, using an experimentally determined calibration curve. Due to the thinness of the sandwich, indentation negligibly affected the precision of the results, with the apparent rigidities differing from the actual ones by less than 2%. By an analytical formula previously developed for sandwich structures, a prediction of the rigidities in flexure was attempted, adopting elastic constants available in the literature. The correlation with the data points was poor, with the theoretical results largely overestimating the actual rigidities. However, the reliability of the closed-form formula was supported by finite element analysis, carried out modelling the facings by 2D plate elements, and the core by 3D brick elements. Through the formula, the core shear modulus was individuated as responsible of the discrepancies observed. Assuming a suitable value for this parameter, both the analytic solution and the finite element models were able to match with accuracy the rigidities measured.

  4. Thermal conductivity of newspaper sandwiched aerated lightweight concrete panel

    Energy Technology Data Exchange (ETDEWEB)

    Ng, Soon-Ching; Low, Kaw-Sai [Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Genting Kelang, Setapak, 53300 Kuala Lumpur, Wilayah Persekutuan (Malaysia)

    2010-12-15

    Investigation on the thermal conductivity of newspaper sandwiched aerated lightweight concrete (ALC) panels is the main purpose of this study. Various densities of ALC panels ranging from 1700, 1400 and 1100 kg/m{sup 3} with three different aerial intensities of newspaper sandwiched were produced. Investigation was limited to the effect of aerial intensity of newspaper sandwiched and the effect of density of ALC on thermal conductivity. It is found that the thermal conductivity of newspaper sandwiched ALC panels reduced remarkably compared to control ALC panels. The reduction was recorded at 18.0%, 21.8% and 20.7% correspond to densities of 1700, 1400 and 1100 kg/m{sup 3} with just a mere 0.05 g/cm{sup 2} aerial intensity of newspaper sandwiched. Newspaper sandwiched has a significant impact on the performance of thermal conductivity of ALC panels based on regression analysis. (author)

  5. Influence of plywood grain direction on sandwich panel bending properties

    OpenAIRE

    Jaroslav Kljak; Mladen Brezović; Alan Antonović

    2009-01-01

    This paper investigates the influence of plywood grain direction on bending properties of a sandwich panel, as well as on stress distribution in each layer. Experimental sandwich panels (tnom= 29 mm) were made of two three-ply plywood panels and a rigid PVC core between them. Grain directions of plywood panels were between 0° and 90°, continuously raised by 15°. Seven models of sandwich panels were made. Bending properties of a sandwich panel was determined by three point bending method and s...

  6. Buckling Analysis of Debonded Sandwich Panel Under Compression

    Science.gov (United States)

    Sleight, David W.; Wang, John T.

    1995-01-01

    A sandwich panel with initial through-the-width debonds is analyzed to study the buckling of its faceskin when subject to an in-plane compressive load. The debonded faceskin is modeled as a beam on a Winkler elastic foundation in which the springs of the elastic foundation represent the sandwich foam. The Rayleigh-Ritz and finite-difference methods are used to predict the critical buckling load for various debond lengths and stiffnesses of the sandwich foam. The accuracy of the methods is assessed with a plane-strain finite-element analysis. Results indicate that the elastic foundation approach underpredicts buckling loads for sandwich panels with isotropic foam cores.

  7. Analytical determination of the ultimate strength of sandwich beams

    Science.gov (United States)

    Theotokoglou, Efstathios E.

    1996-09-01

    An analytical determination of the ultimate strength of a typical GRP/PVC sandwich beam has been performed. These beams represent common building practise in marine applications. Equations describing the behaviour of a sandwich panel under beam loading and various failure modes have been developed. The method has been applied to predict the ultimate load for a simple supported sandwich beam. The critical loads have been compared with those from the experimental investigation of a typical bulkhead-to-hull GRP/PVC sandwich T-joint under pull out forces.

  8. Elastic constants for superplastically formed/diffusion-bonded sandwich structures

    Science.gov (United States)

    Ko, W. L.

    1979-01-01

    Formulae and the associated graphs are presented for contrasting the effective elastic constants for a superplastically formed/diffusion-bonded (SPF/DB) corrugated sandwich core and a honeycomb sandwich core. The results used in the comparison of the structural properties of the two types of sandwich cores are under conditions of equal sandwich density. It was found that the stiffness in the thickness direction of the optimum SPF/DB corrugated core (i.e., triangular truss core) was lower than that of the honeycomb core, and that the former had higher transverse shear stiffness than the latter.

  9. A double-sandwich ELISA for identification of monoclonal antibodies suitable for sandwich immunoassays

    Science.gov (United States)

    The sandwich immunoassay (sIA) is an invaluable technique for concentrating, detecting, and quantifying target antigens. The two critical components required are a capture antibody and a detection antibody, each binding a different epitope on the target antigen. The specific antibodies incorporated...

  10. On curves on sandwiched surface singularities

    OpenAIRE

    Fernandez-Sanchez, Jesus

    2007-01-01

    Fixed a point O on a non-singular surface S and a complete mO-primary ideal I in its local ring, the curves on the surface X obtained by blowing-up I are studied in terms of the base points of I. Criteria for the principality of these curves are obtained. New formulas for their multiplicity, intersection numbers and order of singularity at the singularities of X are given. The semigroup of branches going through a sandwiched singularity is effectively determined, too.

  11. Failure modes of composite sandwich beams

    Directory of Open Access Journals (Sweden)

    Gdoutos E.

    2008-01-01

    Full Text Available A thorough investigation of failure behavior of composite sandwich beams under three-and four-point bending was undertaken. The beams were made of unidirectional carbon/epoxy facings and a PVC closed-cell foam core. The constituent materials were fully characterized and in the case of the foam core, failure envelopes were developed for general two-dimensional states of stress. Various failure modes including facing wrinkling, indentation failure and core failure were observed and compared with analytical predictions. The initiation, propagation and interaction of failure modes depend on the type of loading, constituent material properties and geometrical dimensions.

  12. Recent trends in aluminum foam sandwich technology

    Energy Technology Data Exchange (ETDEWEB)

    Banhart, John [TU Berlin, Materials Science and Technology, Hardenbergstr. 36, 10623 Berlin (Germany); Helmholtz-Centre Berlin, Hahn-Meitner-Platz, 14109 Berlin (Germany); Seeliger, Hans-Wolfgang [Pohltec Metalfoam GmbH, Robert-Bosch-Str. 6D, 50769 Koeln (Germany)

    2012-12-15

    We review the status of aluminum foam sandwich (AFS) technology and discuss both recent improvements of foaming technology and current application strategies. It is concluded that the quality of foams has improved in the past years but the costs are still very much the same. This is why applications in which metal foams have more than one function are more likely to be economically viable. The examples presented include electromagnetic shielding, carrier plates for mirrors, cooking equipment, architectural panels, and blast protection. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. 2003 Dead Bald Eagle Specimen

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The specimen report states the Bald Eagle was found along the side of the I-95 by a motorist who contacted Santee National Wildlife Refuge. The Bald Eagle was taken...

  14. Manufacturing of Plutonium Tensile Specimens

    Energy Technology Data Exchange (ETDEWEB)

    Knapp, Cameron M [Los Alamos National Laboratory

    2012-08-01

    Details workflow conducted to manufacture high density alpha Plutonium tensile specimens to support Los Alamos National Laboratory's science campaigns. Introduces topics including the metallurgical challenge of Plutonium and the use of high performance super-computing to drive design. Addresses the utilization of Abaqus finite element analysis, programmable computer numerical controlled (CNC) machining, as well as glove box ergonomics and safety in order to design a process that will yield high quality Plutonium tensile specimens.

  15. Application of lock-in thermography for the inspection of disbonds in titanium alloy honeycomb sandwich structure

    Science.gov (United States)

    Zhao, Hanxue; Zhou, Zhenggan; Fan, Jin; Li, Gen; Sun, Guangkai

    2017-03-01

    This paper investigates the lock-in thermography testing of skin-to-core disbonds in titanium alloy honeycomb structure. A three-dimensional finite element model of titanium alloy honeycomb sandwich structure is built. The phase difference between the disbond defect region and the nondefective region is used to optimize the excitation frequency. The phase variation of the surface temperature because of the discontinuity of the honeycomb structure is analyzed. And the relationship between the phase difference of the defect and the nondefective region and the thickness of the disbond is obtained. Two titanium alloy honeycomb sandwich structure specimens with skin-to-core disbond defects were manufactured. Different from the conventional method of simulating disbond defects, two methods of prefabricating intimate contact disbond are proposed to form real defects. The lock-in thermography experiments are carried out on the specimens. The digital correlation method is used to process the infrared image sequence. The experimental results show that lock-in thermography is effective in inspecting the intimate contact disbond in titanium alloy honeycomb sandwich structure.

  16. Dynamic Failure of Composite and Sandwich Structures

    CERN Document Server

    Abrate, Serge; Rajapakse, Yapa D S

    2013-01-01

    This book presents a broad view of the current state of the art regarding the dynamic response of composite and sandwich structures subjected to impacts and explosions. Each chapter combines a thorough assessment of the literature with original contributions made by the authors.  The first section deals with fluid-structure interactions in marine structures.  The first chapter focuses on hull slamming and particularly cases in which the deformation of the structure affects the motion of the fluid during the water entry of flexible hulls. Chapter 2 presents an extensive series of tests underwater and in the air to determine the effects of explosions on composite and sandwich structures.  Full-scale structures were subjected to significant explosive charges, and such results are extremely rare in the open literature.  Chapter 3 describes a simple geometrical theory of diffraction for describing the interaction of an underwater blast wave with submerged structures. The second section addresses the problem of...

  17. Sandwich materials for wind turbine blades

    Energy Technology Data Exchange (ETDEWEB)

    Thybo Thomsen, O. [Aalborg Univ., Dept. of Mechanical Engineering, Aalborg (Denmark)

    2006-07-01

    Wind turbine blades are being manufactured using polymer matrix composite materials (PMC), in a combination of monolithic (single skin) and sandwich composites. Present day designs are mainly based on glass fibre reinforced composites (GFRP), but for very large blades carbon fibre reinforced composites (CFRP) are being used increasingly, in addition to GFRP by several manufacturers to reduce the weight. The size of wind turbines have increased significantly over the last 25 years, and this trend is expected to continue in the future. Thus, it is anticipated that wind turbines with a rated power output in the range of 8-10 MW and a rotor diameter about 170-180 m will be developed and installed within the next 10-15 years. The paper presents an overview of current day design principles and materials technology applied for wind turbine blades, and it highlights the limitations and important design issues to be addressed for up-scaling of wind turbine blades from the current maximum length in excess of 61 m to blade lengths in the vicinity of 90 m as envisaged for future very large wind turbines. In particular, the paper discusses the potential advantages and challenges of applying sandwich type construction to a larger extent than is currently being practiced for the load carrying parts of wind turbine blades. (au)

  18. Quantum radiation from a sandwich black hole

    Science.gov (United States)

    Frolov, Valeri P.; Zelnikov, Andrei

    2017-02-01

    We discuss quantum radiation of a massless scalar field from a spherically symmetric nonsingular black hole with a finite lifetime. Namely, we discuss a sandwich black-hole model, where a black hole is originally created by a collapse of a null shell of mass M , and later, after some time Δ V , it is disrupted by the collapse of the other shell with negative mass -M . We assume that between the shells the metric is static and either coincides with the Hayward metric or with a special generalization of it. We show that in both cases for a sufficiently large parameter Δ V the radiation after the formation of the black hole practically coincides with the Hawking result. We also calculate the radiation, emitted from the black hole interior. This radiation contains a peak at the moment when the second shell intersects the inner horizon. In the standard sandwich metric (with the Hayward interior) this outburst of energy is exponentially large. In the modified metric, which includes an additional nontrivial redshift parameter, this exponent is suppressed. This is a result of a significant decrease of the surface gravity of the inner horizon in the latter case. We discuss possible consequences of this result in the context of the self-consistency requirement for nonsingular models with quantum radiation.

  19. Fracture Analysis of Debonded Sandwich Columns Under Axial Compression

    DEFF Research Database (Denmark)

    May, A.; Avilés, F.; Berggreen, Christian

    A sandwich structure consists of two strong and stiff face sheets bonded to a weak low density core. The large separation between the face sheets provides increased bending rigidity and strength at low weight cost. Thus, sandwich structures frequently present better mechanical properties than mon...

  20. Practical Instruction in Tissue Culture and Cytogenetics for Sandwich Students.

    Science.gov (United States)

    Williams, D. C.; Bishun, N. P.

    1973-01-01

    Describes the training and practical techniques taught to students involved in a sandwich course at the Tissue Culture and Cytogenetics Unit of the Marie Curie Memorial Foundation, Surrey, England. Students spend a minimum of six months involved in the sandwich course before returning to university for a final academic year. (JR)

  1. Query processing of pre-partitioned data using Sandwich Operators

    NARCIS (Netherlands)

    Baumann, S.; Boncz, P.A.; Sattler, K.-U.

    2012-01-01

    In this paper we present the Sandwich Operators, an elegant approach to exploit pre-sorting or pre-grouping from clustered storage schemes in operators such as Aggregation/Grouping, HashJoin, and Sort of a database management system. Thereby, each of these operator types is "sandwiched" by two new o

  2. Tailoring Sandwich Face/Core Interfaces for Improved Damage Tolerance

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Berggreen, Christian; Carlsson, Leif A.

    2010-01-01

    A face/core debond in a sandwich structure may propagate in the interface or kink into either the face or core. It is found that certain modifications of the face/core interface region influence the kinking behavior, which is studied experimentally in the present paper. A sandwich double cantilever...

  3. Fracture Analysis of Debonded Sandwich Columns Under Axial Compression

    DEFF Research Database (Denmark)

    May, A.; Avilés, F.; Berggreen, Christian

    A sandwich structure consists of two strong and stiff face sheets bonded to a weak low density core. The large separation between the face sheets provides increased bending rigidity and strength at low weight cost. Thus, sandwich structures frequently present better mechanical properties than mon...

  4. Thick Plate Homogenization of Sandwich Panels Including Folded Cellular Cores

    OpenAIRE

    LEBEE, Arthur; Sab, Karam

    2011-01-01

    In the present work, we provide the Bending-Gradient homogenization scheme and apply it to a sandwich panel including the chevron pattern. It turns out that the shear forces stiffness of the sandwich panel is strongly influenced by a skin distortion phenomenon which cannot be neglected in conventional design.

  5. Finite Element Modeling of the Buckling Response of Sandwich Panels

    Science.gov (United States)

    Rose, Cheryl A.; Moore, David F.; Knight, Norman F., Jr.; Rankin, Charles C.

    2002-01-01

    A comparative study of different modeling approaches for predicting sandwich panel buckling response is described. The study considers sandwich panels with anisotropic face sheets and a very thick core. Results from conventional analytical solutions for sandwich panel overall buckling and face-sheet-wrinkling type modes are compared with solutions obtained using different finite element modeling approaches. Finite element solutions are obtained using layered shell element models, with and without transverse shear flexibility, layered shell/solid element models, with shell elements for the face sheets and solid elements for the core, and sandwich models using a recently developed specialty sandwich element. Convergence characteristics of the shell/solid and sandwich element modeling approaches with respect to in-plane and through-the-thickness discretization, are demonstrated. Results of the study indicate that the specialty sandwich element provides an accurate and effective modeling approach for predicting both overall and localized sandwich panel buckling response. Furthermore, results indicate that anisotropy of the face sheets, along with the ratio of principle elastic moduli, affect the buckling response and these effects may not be represented accurately by analytical solutions. Modeling recommendations are also provided.

  6. Optimization of sandwich composites fuselages under flight loads

    NARCIS (Netherlands)

    Yan, C.; Bergsma, O.; Koussios, S.; Zu, L.; Beukers, A.

    2010-01-01

    The sandwich composites fuselages appear to be a promising choice for the future aircrafts because of their structural efficiency and functional integration advantages. However, the design of sandwich composites is more complex than other structures because of many involved variables. In this paper,

  7. Design and manufacturing of bio-based sandwich structures

    CSIR Research Space (South Africa)

    John, Maya J

    2017-03-01

    Full Text Available The aim of this chapter is to discuss the design and manufacturing of bio-based sandwich structures. As the economic advantages of weight reduction have become mandatory for many advanced industries, bio-based sandwich panels have emerged...

  8. Development, testing, and numerical modeling of a foam sandwich biocomposite

    Science.gov (United States)

    Chachra, Ricky

    This study develops a novel sandwich composite material using plant based materials for potential use in nonstructural building applications. The face sheets comprise woven hemp fabric and a sap based epoxy, while the core comprises castor oil based foam with waste rice hulls as reinforcement. Mechanical properties of the individual materials are tested in uniaxial compression and tension for the foam and hemp, respectively. The sandwich composite is tested in 3 point bending. Flexural results are compared to a finite element model developed in the commercial software Abaqus, and the validated model is then used to investigate alternate sandwich geometries. Sandwich model responses are compared to existing standards for nonstructural building panels, showing that the novel material is roughly half the strength of equally thick drywall. When space limitations are not an issue, a double thickness sandwich biocomposite is found to be a structurally acceptable replacement for standard gypsum drywall.

  9. Data characterizing flexural properties of Al/Al2O3 syntactic foam core metal matrix sandwich

    Directory of Open Access Journals (Sweden)

    Mohammed Yaseer Omar

    2015-12-01

    Full Text Available Microstructural observations and flexural property datasets are provided for aluminum alloy matrix syntactic foam core sandwich composites. The tests are conducted in three-point bending configuration. The data supplied includes methods used for conducting microscopy and mechanical testing. Raw load–displacement data, which is used to plot stress–strain graphs, obtained during the flexural test is also included. Images from a DSLR camera are stitched together to form a detailed failure sequencing video. Failure of specimens is captured in sequential images using a digital camera. These images are stitched together to develop a video for visualization of failure mechanisms. Calculations are also included for a theoretical model that is used to estimate the flexural properties of the syntactic foam core sandwich.

  10. Ultrasonic guided wave characterization and damage detection in foam-core sandwich panel using PWAS and LDV

    Science.gov (United States)

    Chakraborty, Nibir; Roy Mahapatra, D.; Srinivasan, Gopalakrishnan

    2012-04-01

    Lamb wave type guided wave propagation in foam core sandwich structures and detectability of damages using spectral analysis method are reported in this paper. An experimental study supported by theoretical evaluation of the guided wave characteristics is presented here that shows the applicability of Lamb wave type guided ultrasonic wave for detection of damage in foam core sandwich structures. Sandwich beam specimens were fabricated with 10 mm thick foam core and 0.3 mm thick aluminum face sheets. Thin piezoelectric patch actuators and sensors are used to excite and sense guided wave. Group velocity dispersion curves and frequency response of sensed signal are obtained experimentally. The nature of damping present in the sandwich panel is monitored by measuring the sensor signal amplitude at various different distances measured from the center of the linear phased array. Delaminations of increasing width are created and detected experimentally by pitch-catch interrogation with guided waves and wavelet transform of the sensed signal. Signal amplitudes are analyzed for various different sizes of damages to differentiate the damage size/severity. A sandwich panel is also fabricated with a planer dimension of 600 mm x 400 mm. Release film delamination is introduced during fabrication. Non-contact Laser Doppler Vibrometer (LDV) is used to scan the panel while exciting with a surface bonded piezoelectric actuator. Presence of damage is confirmed by the reflected wave fringe pattern obtained from the LDV scan. With this approach it is possible to locate and monitor the damages by tracking the wave packets scattered from the damages.

  11. Efficacy of four lining materials in sandwich technique to reduce microleakage in class II composite resin restorations.

    Science.gov (United States)

    Moazzami, S M; Sarabi, N; Hajizadeh, H; Majidinia, S; Li, Y; Meharry, M R; Shahrokh, H

    2014-01-01

    The aim of the present study was to evaluate the effect of four different sandwich techniques on gingival microleakage of Class II direct composite resin restorations. Fifty sound human premolars were selected and randomly divided into five groups (n=10). Class II box only cavities were prepared in one of the proximal surfaces of each tooth with a gingival margin located approximately 0.5 mm below the cemento-enamel junction. Group A (control) was restored incrementally with composite resin (Tetric Ceram). Groups B, C, D, and E were restored with the sandwich technique using a compomer (Compoglass F), flowable composite resin (Tetric Flow), self-cure composite resin (Degufill SC), or resin modified glass ionomer (Fuji II LC), respectively. After thermal-load cycling, the specimens were immersed in 0.5% basic fuschin for 24 hours. Dye penetration (10(-1) mm) was detected using a sectioning technique. Data were analyzed with repeated measurements and Duncan test at α=0.05. The least amount of microleakage was detected in the incremental group (1.28 ± 0.98). The sandwich technique using resin modified glass ionomer (7.99 ± 9.57) or compomer (4.36 ± 1.78) resulted in significantly more leakage than did the sandwich technique using flowable (1.50 ± 1.97) or self-cure composite (2.26 ± 1.52). According to the results of this study, none of the four sandwich technique composite resin restorations used in this study could reduce gingival microleakage to a greater degree than the incremental technique.

  12. Influence of the inter-layer adhesion on the structural strength of sandwich pipes; Influencia da adesao entre camadas na resistencia estrutural de dutos sanduiche

    Energy Technology Data Exchange (ETDEWEB)

    Castello, Xavier; Estefen, Segen [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia. Programa de Engenharia Oceanica

    2005-07-01

    Sandwich pipes composed of two steel layers separated by a polypropylene annulus can be used for the transport of oil and gas in deep waters, combining high structural resistance with thermal insulation in order to prevent blockage by paraffin and hydrates. In this work, sandwich pipes with typical inner diameters of those employed in the offshore production are analyzed numerically regarding to the influence of the inter-layer adhesion of steel pipes and polymer on the limit strength under external pressure and longitudinal bending as well as the bending and straightening process representative of the reeling installation method. The numerical model incorporates geometric and material non-linearity, which had been based on previous works of the authors. Tests of specimens under tension and segments of sandwich pipes are carried through to evaluate the maximum shear stresses of the interfaces metal-polymer. The adhesion is modeled by contact adopting a maximum shear stress value to allow the relative displacement between the layers. It was observed that the structural resistance of the sandwich pipe is strongly dependent on the shear stress acting at the interface, occurring the collapse of the pipe when the maximum shear stress is reached. The results obtained are analyzed to determine the minimum shear strength at the union which provides adequate structural resistance for the sandwich pipe under representative conditions of the installation and operation loading phases. (author)

  13. Standard Test Method for Sandwich Corrosion Test

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This test method defines the procedure for evaluating the corrosivity of aircraft maintenance chemicals, when present between faying surfaces (sandwich) of aluminum alloys commonly used for aircraft structures. This test method is intended to be used in the qualification and approval of compounds employed in aircraft maintenance operations. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements appear in Section 9.

  14. Nanoparticle organization in sandwiched polymer brushes.

    Science.gov (United States)

    Curk, Tine; Martinez-Veracoechea, Francisco J; Frenkel, Daan; Dobnikar, Jure

    2014-05-14

    The organization of nanoparticles inside grafted polymer layers is governed by the interplay of polymer-induced entropic interactions and the action of externally applied fields. Earlier work had shown that strong external forces can drive the formation of colloidal structures in polymer brushes. Here we show that external fields are not essential to obtain such colloidal patterns: we report Monte Carlo and molecular dynamics simulations that demonstrate that ordered structures can be achieved by compressing a "sandwich" of two grafted polymer layers, or by squeezing a coated nanotube, with nanoparticles in between. We show that the pattern formation can be efficiently controlled by the applied pressure, while the characteristic length-scale, that is, the typical width of the patterns, is sensitive to the length of the polymers. Based on the results of the simulations, we derive an approximate equation of state for nanosandwiches.

  15. Development and Mechanical Behavior of FML/Aluminium Foam Sandwiches

    Science.gov (United States)

    Baştürk, S. B.; Tanoğlu, M.

    2013-10-01

    In this study, the Fiber-Metal Laminates (FMLs) containing glass fiber reinforced polypropylene (GFPP) and aluminum (Al) sheet were consolidated with Al foam cores for preparing the sandwich panels. The aim of this article is the comparison of the flexural properties of FML/Al foam sandwich panels bonded with various surface modification approaches (silane treatment and combination of silane treatment with polypropylene (PP) based film addition). The FML/foam sandwich systems were fabricated by laminating the components in a mould at 200 °C under 1.5 MPa pressure. The energy absorbtion capacities and flexural mechanical properties of the prepared sandwich systems were evaluated by mechanical tests. Experiments were performed on samples of varying foam thicknesses (8, 20 and 30 mm). The bonding among the sandwich components were achieved by various surface modification techniques. The Al sheet/Al foam sandwiches were also consolidated by bonding the components with an epoxy adhesive to reveal the effect of GFPP on the flexural performance of the sandwich structures.

  16. Wave propagation in sandwich panels with a poroelastic core.

    Science.gov (United States)

    Liu, Hao; Finnveden, Svante; Barbagallo, Mathias; Arteaga, Ines Lopez

    2014-05-01

    Wave propagation in sandwich panels with a poroelastic core, which is modeled by Biot's theory, is investigated using the waveguide finite element method. A waveguide poroelastic element is developed based on a displacement-pressure weak form. The dispersion curves of the sandwich panel are first identified as propagating or evanescent waves by varying the damping in the panel, and wave characteristics are analyzed by examining their motions. The energy distributions are calculated to identify the dominant motions. Simplified analytical models are also devised to show the main physics of the corresponding waves. This wave propagation analysis provides insight into the vibro-acoustic behavior of sandwich panels lined with elastic porous materials.

  17. Thermal behavior of a titanium honeycomb-core sandwich panel

    Science.gov (United States)

    Ko, William L.; Jackson, Raymond H.

    1991-01-01

    Finite element thermal stress analysis was performed on a rectangular titanium honecomb-core sandwich panel which is subjected to thermal load with a temperature gradient across its depth. The distributions of normal stresses in the face sheets and the face-sheet/sandwich-core interfacial shear stresses are presented. The thermal buckling of the heated face sheet was analyzed by assuming the face sheet to be resting on an elastic foundation representing the sandwich core. Thermal buckling curves and thermal buckling load surface are presented for setting the limit for temperature gradient across the panel depth.

  18. Sandwich Panel as a Structural Element of Overlap

    Directory of Open Access Journals (Sweden)

    Novikov Maxim

    2016-01-01

    Full Text Available This paper considers the issue of sandwich panels using as load-bearing structural elements. The comparison of deflections and critical failure loads were obtained by the results of the full-scale roof sandwich panels tests conducted by the company “Joris Ide” and the theoretical design, according to the calculation method described in Euronorms. Based on these results it was concluded that sandwich panels can be treated as a load-bearing structure only with more taught manufacturing requirements. Thus, the reduced spread of critical loads can be achieved.

  19. Evaluation of the Transient Liquid Phase (TLP) Bonding Process for Ti3Al-Based Honeycomb Core Sandwich Structure

    Science.gov (United States)

    Bird, R. Keith; Hoffman, Eric K.

    1998-01-01

    The suitability of using transient liquid phase (TLP) bonding to fabricate honeycomb core sandwich panels with Ti-14Al-21Nb (wt%) titanium aluminide (T3Al) face sheets for high-temperature hypersonic vehicle applications was evaluated. Three titanium alloy honeycomb cores and one Ti3Al alloy honeycomb core were investigated. Edgewise compression (EWC) and flatwise tension (FWT) tests on honeycomb core sandwich specimens and tensile tests of the face sheet material were conducted at temperatures ranging from room temperature to 1500 F. EWC tests indicated that the honeycomb cores and diffusion bonded joints were able to stabilize the face sheets up to and beyond the face sheet compressive yield strength for all temperatures investigated. The specimens with the T3Al honeycomb core produced the highest FWT strengths at temperatures above 1000 F. Tensile tests indicated that TLP processing conditions resulted in decreases in ductility of the Ti-14Al-21Nb face sheets. Microstructural examination showed that the side of the face sheets to which the filler metals had been applied was transformed from equiaxed alpha2 grains to coarse plates of alpha2 with intergranular Beta. Fractographic examination of the tensile specimens showed that this transformed region was dominated by brittle fracture.

  20. Successful mouse hepatocyte culture with sandwich collagen gel formation

    National Research Council Canada - National Science Library

    Choi, Hyun Jung; Choi, Dongho

    2013-01-01

    .... However, long-term cultures of functional hepatocytes are difficult to establish. To increase the longevity and maintain the differentiated functions of hepatocytes in primary culture, cells can be cultured in a sandwich configuration of collagen...

  1. Outcome of the TURP-TUVP sandwich procedure for minimally ...

    African Journals Online (AJOL)

    shanker

    TURP–TUVP sandwich procedure for the surgical treatment of BPH larger than 40cc in ... volume larger than 40cc had satisfactory patient safety profile and resulted in .... ment, nursing contact time, and duration of catheterization, besides.

  2. Sandwich-like reconstruction of anterior skull base defects

    Institute of Scientific and Technical Information of China (English)

    WANG Zhengmin; WANG Dehui

    2002-01-01

    @@ RESULTS From October, 1984 to October, 1998, 116 patients underwent transcranial or transcranial-facial approach for the resection of malignant or benign aggressive tumor, and sandwich-like repairs were performed for the anterior skull base defect.

  3. Mechanical and vibro-acoustic aspects of composite sandwich cylinders

    NARCIS (Netherlands)

    Yuan, C.

    2013-01-01

    Designing a fuselage involves many considerations such as strength and stability, fatigue, damage tolerance, fire and lightning resistance, thermal and acoustic insulation, production, inspection, maintenance and repair. In the background of the application of composite sandwich structures on the ai

  4. Mechanical and vibro-acoustic aspects of composite sandwich cylinders

    NARCIS (Netherlands)

    Yuan, C.

    2013-01-01

    Designing a fuselage involves many considerations such as strength and stability, fatigue, damage tolerance, fire and lightning resistance, thermal and acoustic insulation, production, inspection, maintenance and repair. In the background of the application of composite sandwich structures on the ai

  5. Observability and Controllability Analysis for Sandwich Systems with Backlash

    Directory of Open Access Journals (Sweden)

    Luo Na

    2015-12-01

    Full Text Available In this paper, an approach to analyze the observability and controllability of sandwich systems with backlash is proposed. In this method, a non-smooth state-space function is used to describe the sandwich systems with backlash which are also non-smooth non-linear systems. Then, a linearization method based on non-smooth optimization is proposed to derive a linearized state-space function to approximate the non-smooth sandwich systems within a bounded region around the equilibrium point that we are interested in. Afterwards, both observability and controllability matrices are constructed and the methods to analyze the observability as well as controllability of sandwich system with backlash are derived. Finally, numerical examples are presented to validate the proposed method.

  6. Mechanical and vibro-acoustic aspects of composite sandwich cylinders

    NARCIS (Netherlands)

    Yuan, C.

    2013-01-01

    Designing a fuselage involves many considerations such as strength and stability, fatigue, damage tolerance, fire and lightning resistance, thermal and acoustic insulation, production, inspection, maintenance and repair. In the background of the application of composite sandwich structures on the

  7. Residual Strength Prediction of Debond Damaged Sandwich Panels

    DEFF Research Database (Denmark)

    Berggreen, Carl Christian

    This presentation concerns theoretical and experimental prediction of crack propagation and residual strength of debond damaged sandwich panels. It is evident that in order to achieve highly optimised structures which are able to operate in a stochastic loading environment, damage tolerance...... propagation and initiation, as these mechanisms are governing for the overall failure load of the structure. Thus, this presentation will describe the development, validation and application of a FEM based numerical model for prediction of residual strength of damaged sandwich panels. The core......, but they are especially relevant for sandwich structures which by nature are highly optimised structures with a high number of possible damage scenarios and consequent failure mechanisms. A major challenge in estimation of structural integrity of damaged sandwich structures is modelling and prediction of crack...

  8. Fracture Characterization of Sandwich Face/Core Interfaces

    DEFF Research Database (Denmark)

    Manca, Marcello

    such result it is important to devise new experimental and analytical techniques to establish the multi-mode fracture characteristics of sandwich plate structures and accordingly develop methods to inhibit defect propagation. This thesis deals with characterization of fracture between face and core...... samples. A number of sandwich materials were tested (GFRP/foam cores and CFRP/Nomex) bothin static and fatigue. A linear elastic fracture mechanics model was used to determine the analyticalexpression of compliance which allowed to calculate automatically the crack length. In combination, a finite element...... types of sandwich samples atdifferent mode mixities and ΔG levels, and results in agreement with previous studies were obtained suggesting that the developed testing method is a reliable tool for the study of face/core interface debonded sandwich structures....

  9. Forced vibration of a shear thickening fluid sandwich beam

    Science.gov (United States)

    Wei, Minghai; Hu, Gang; Jin, Lu; Lin, Kun; Zou, Dujian

    2016-05-01

    The forced vibration of a sandwich beam integrating a shear thickening fluid (STF) core and with conductive skins subjected to a periodic excitation was investigated theoretically in this study. The rheological properties of the STF material including viscosity, plasticity, and elasticity may be changed under the periodic vibration, and hence they were considered. The governing equation of motion was derived based on the complex stiffness method and some key parameters were derived based on the Timoshenko beam theory. Effects of the excitation frequency, the excitation amplitude, the excitation location, and the skin/core thickness ratio on the nature frequency of the sandwich beam were investigated. It was found that the STF core has a significant effect on the dynamic property of the sandwich beam. Based on the findings, integrating the STF core in a sandwich beam can reduce the vibration of the beam.

  10. Specimen Collection and Submission Manual

    Science.gov (United States)

    2016-06-01

    a validated test algorithm . If there is insufficient specimen volume for testing, there may be delays, and the request may be referred to management...Additional guidance on packing and shipping infectious substances can be found through American Society for Microbiology: http://www.asm.org...images/pdf/Clinical/ pack -ship-7-15-2011.pdf TR-16-161 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. UNCLASSIFIED

  11. Fungal contaminants in cytopathology specimens

    Directory of Open Access Journals (Sweden)

    Prashant Sharma

    2014-02-01

    Full Text Available A pseudo-epidemic of environmental fungi, most likely by Fusarium spp., leading to inappropriate investigations for disseminated systemic mycosis is described. Subtle diagnostic clues, including the specimens affected, the nature of the host response, and the type of fungal elements noted helped to determine the nature of contaminants. The potential pitfall can be avoided by the knowledge of pertinent disease biology, prompt consultation for infectious diseases, and investigations of the potential environmental sources followed by source control.

  12. Compression After Impact on Honeycomb Core Sandwich Panels With Thin Facesheets. Part 1; Experiments

    Science.gov (United States)

    McQuigg, Thomas D.; Kapania, Rakesh K.; Scotti, Stephen J.; Walker, Sandra P.

    2012-01-01

    A two part research study has been completed on the topic of compression after impact (CAI) of thin facesheet honeycomb core sandwich panels. The research has focused on both experiments and analysis in an effort to establish and validate a new understanding of the damage tolerance of these materials. Part one, the subject of the current paper, is focused on the experimental testing. Of interest are sandwich panels, with aerospace applications, which consist of very thin, woven S2-fiberglass (with MTM45-1 epoxy) facesheets adhered to a Nomex honeycomb core. Two sets of specimens, which were identical with the exception of the density of the honeycomb core, were tested. Static indentation and low velocity impact using a drop tower are used to study damage formation in these materials. A series of highly instrumented CAI tests was then completed. New techniques used to observe CAI response and failure include high speed video photography, as well as digital image correlation (DIC) for full-field deformation measurement. Two CAI failure modes, indentation propagation, and crack propagation, were observed. From the results, it can be concluded that the CAI failure mode of these panels depends solely on the honeycomb core density.

  13. Lightweight Sandwich Panel in Cold Stores and Refrigerated Warehouses

    OpenAIRE

    Chidom, Charles

    2013-01-01

    The use of sandwich panels has gained considerable recognition in the construction industry and more use of this composite structure is ever increasing. This study highlights and familiarizes the use of lightweight sandwich panel in refrigerated warehouses and cold storage facility and construction and the challenges such construction faces in warm climates considering the effects of thermal load. The study was commissioned by HAMK Sheet Metal Center, the steel research and development ce...

  14. Optimization of composite sandwich cover panels subjected to compressive loadings

    Science.gov (United States)

    Cruz, Juan R.

    1991-01-01

    An analysis and design method is presented for the design of composite sandwich cover panels that include the transverse shear effects and damage tolerance considerations. This method is incorporated into a sandwich optimization computer program entitled SANDOP. As a demonstration of its capabilities, SANDOP is used in the present study to design optimized composite sandwich cover panels for for transport aircraft wing applications. The results of this design study indicate that optimized composite sandwich cover panels have approximately the same structural efficiency as stiffened composite cover panels designed to satisfy individual constraints. The results also indicate that inplane stiffness requirements have a large effect on the weight of these composite sandwich cover panels at higher load levels. Increasing the maximum allowable strain and the upper percentage limit of the 0 degree and +/- 45 degree plies can yield significant weight savings. The results show that the structural efficiency of these optimized composite sandwich cover panels is relatively insensitive to changes in core density. Thus, core density should be chosen by criteria other than minimum weight (e.g., damage tolerance, ease of manufacture, etc.).

  15. Electronically asymmetric bis(porphyrin) sandwich complexes

    Energy Technology Data Exchange (ETDEWEB)

    Girolami, G.S.; Gorlin, P.A.; Suslick, K.S. [Univ. of Illinois, Urbana, IL (United States)

    1994-02-16

    Bis(porphyrin)metal(IV) complexes (M(porph){sub 2}) have been extensively studies in recent years due to their structural, chemical, and spectroscopic similarity to the {open_quotes}special pair{close_quotes} found in the reaction center of photosynthetic bacteria. Strong interactions arise in the bis(porphyrin) complexes due to the short inter-porphyrin separation (< 3 {angstrom}), which results in properties not seen in mono(porphyrin) analogs. For example, the bis(porphyrin) complexes are considerably easier to oxidize than analogous mono(porphyrin) species, and the M(porph){sub 2{sup n+}} cations (n = 1,2) exhibit near-IR absorptions not found in simple mono(porphyrin)cations. As part of the authors continuing effort to understand the factors that govern the electronic structures of bis(porphyrin) supermolecules, the authors now describe the synthesis of a series of zirconium sandwich complexes. Introduction of electron-withdrawing or -donating groups on the {beta}-pyrrole position considerably affects the electronic properties of these molecules without altering their steric parameters. Thus, peripheral substitution allows modification of the inter-porphyrin {pi} interactions while keeping the inter-porphyrin separation constant. Previous studies have changed the identity of the central metal, but the electronic structure and the interplanar distance could not be varied independently.

  16. Quantitative Evaluation by Glucose Diffusion of Microleakage in Aged Calcium Silicate-Based Open-Sandwich Restorations

    Directory of Open Access Journals (Sweden)

    S. Koubi

    2012-01-01

    Full Text Available This study compared the in vitro marginal integrity of open-sandwich restorations based on aged calcium silicate cement versus resin-modified glass ionomer cement. Class II cavities were prepared on 30 extracted human third molars. These teeth were randomly assigned to two groups (=10 to compare a new hydraulic calcium silicate cement designed for restorative dentistry (Biodentine, Septodont, Saint Maur des Fossés, France with a resin-modified glass ionomer cement (Ionolux, Voco, Cuxhaven, Germany in open-sandwich restorations covered with a light-cured composite. Positive (=5 and negative (=5 controls were included. The teeth simultaneously underwent thermocycling and mechanocycling using a fatigue cycling machine (1,440 cycles, 5–55°C; 86,400 cycles, 50 N/cm2. The specimens were then stored in phosphate-buffered saline to simulate aging. After 1 year, the teeth were submitted to glucose diffusion, and the resulting data were analyzed with a nonparametric Mann-Whitney test. The Biodentine group and the Ionolux group presented glucose concentrations of 0.074 ± 0.035 g/L and 0.080 ± 0.032 g/L, respectively. No statistically significant differences were detected between the two groups. Therefore, the calcium silicate-based material performs as well as the resin-modified glass ionomer cement in open-sandwich restorations.

  17. Feasibility study of a SiC sandwich neutron spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Jian, E-mail: caepwujian@163.com [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900, Sichuan Province (China); Lei, Jiarong, E-mail: jiarong_lei@163.com [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900, Sichuan Province (China); Jiang, Yong; Chen, Yu; Rong, Ru; Zou, Dehui; Fan, Xiaoqiang [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900, Sichuan Province (China); Chen, Gang; Li, Li; Bai, Song [Nanjing Electronic Devices Institute, Nanjing 210016 (China)

    2013-04-21

    Semiconductor sandwich neutron spectrometers are suitable for in-pile measurements of fast reactor spectra thanks to their compact and relatively simple design. We have assembled and tested a sandwich neutron spectrometer based on 4H-silicon carbide (4H-SiC) Schottky diodes. The SiC diodes detect neutrons via neutron-induced charged particles (tritons and alpha particles) produced by {sup 6}Li(n,α){sup 3}H reaction. {sup 6}LiF neutron converter layers are deposited on the front surface of Schottky diodes by magnetron sputtering. The responses of SiC diodes to charged particles were investigated with an {sup 241}Am alpha source. A sandwich neutron spectrometer was assembled with two SiC Schottky diodes selected based on the charged-particle-response experimental results. The low-energy neutron response of the sandwich spectrometer was measured in the neutron field of the Chinese Fast Burst Reactor-II (CFBR-II). Spectra of alpha particles and tritons from {sup 6}Li(n,α){sup 3}H reaction were obtained with two well-resolved peaks. The energy resolution of the sum spectrum was 8.8%. The primary experimental results confirmed the 4H-SiC sandwich neutron spectrometer's feasibility. -- Highlights: ► Sandwich neutron spectrometer employing 4H-SiC as a detecting material has been developed for the first time. ► {sup 6}LiF neutron converter has been deposited on the surface of 4H-SiC Schottky diode. ► Preliminary testing results obtained with the 4H-SiC sandwich neutron spectrometer are presented.

  18. Application of sandwich honeycomb carbon/glass fiber-honeycomb composite in the floor component of electric car

    Science.gov (United States)

    Sukmaji, I. C.; Wijang, W. R.; Andri, S.; Bambang, K.; Teguh, T.

    2017-01-01

    Nowadays composite is a superior material used in automotive component due to its outstanding mechanical behavior. The sandwich polypropylene honeycomb core with carbon/glass fiber composite skin (SHCG) as based material in a floor component of electric car application is investigated in the present research. In sandwich structure form, it can absorb noise better compare with the conventional material [1]. Also in present paper, Finite Element Analysis (FEA) of SHCG as based material for floor component of the electric car is analyzed. The composite sandwich is contained with a layer uniform carbon fiber and mixing non-uniform carbon-glass fiber in upper and lower skin. Between skins of SHCG are core polypropylene honeycomb that it have good flexibility to form following dies profile. The variables of volume fraction ratio of carbon/glass fiber in SHCG skin are 20/80%, 30/70%, and 50/50%. The specimen of SHCG is tested using the universal testing machine by three points bending method refers to ASTM C393 and ASTM C365. The cross point between tensile strength to the volume fraction the mixing carbon/glass line and ratio cost line are the searched material with good mechanical performance and reasonable cost. The point is 30/70 volume fraction of carbon/glass fiber. The result of the testing experiment is become input properties of model structure sandwich in FEA simulation. FEA simulation approach is conducted to find critical strength and factor of complex safety geometry against varied distributed passenger loads of a floor component the electric car. The passenger loads variable are 80, 100, 150, 200, 250 and 300 kg.

  19. Hydraulically Driven Grips For Hot Tensile Specimens

    Science.gov (United States)

    Bird, R. Keith; Johnson, George W.

    1994-01-01

    Pair of grips for tensile and compressive test specimens operate at temperatures up to 1,500 degrees F. Grips include wedges holding specimen inside furnace, where heated to uniform temperature. Hydraulic pistons drive wedges, causing them to exert clamping force. Hydraulic pistons and hydraulic fluid remain outside furnace, at room temperature. Cooling water flows through parts of grips to reduce heat transferred to external components. Advantages over older devices for gripping specimens in high-temperature tests; no need to drill holes in specimens, maintains constant gripping force on specimens, and heated to same temperature as that of specimen without risk of heating hydraulic fluid and acuator components.

  20. Response of Honeycomb Core Sandwich Panel with Minimum Gage GFRP Face-Sheets to Compression Loading After Impact

    Science.gov (United States)

    McQuigg, Thomas D.; Kapania, Rakesh K.; Scotti, Stephen J.; Walker, Sandra P.

    2011-01-01

    A compression after impact study has been conducted to determine the residual strength of three sandwich panel constructions with two types of thin glass fiber reinforced polymer face-sheets and two hexagonal honeycomb Nomex core densities. Impact testing is conducted to first determine the characteristics of damage resulting from various impact energy levels. Two modes of failure are found during compression after impact tests with the density of the core precipitating the failure mode present for a given specimen. A finite element analysis is presented for prediction of the residual compressive strength of the impacted specimens. The analysis includes progressive damage modeling in the face-sheets. Preliminary analysis results were similar to the experimental results; however, a higher fidelity core material model is expected to improve the correlation.

  1. Enhancing Fatigue Performance of Sandwich Composites with Nanophased Core

    Directory of Open Access Journals (Sweden)

    S. Zainuddin

    2010-01-01

    Full Text Available We report fatigue performance of sandwich composites with nanophased core under shear load. Nanophased core was made from polyurethane foam dispersed with carbon nanofiber (CNF. CNFs were dispersed into part-A of liquid polyurethane through a sonication process and the loading of nanoparticles was 1.0 wt%. After dispersion, part-A was mixed with part-B, cast into a mold, and allowed to cure. Nanophased foam was then used to fabricate sandwich composites. Static shear tests revealed that strength and modulus of nanophased foams were 33% and 19% higher than those of unreinforced (neat foams. Next, shear fatigue tests were conducted at a frequency of 3 Hz and stress ratio (R of 0.1. S-N curves were generated and fatigue performances were compared. Number of cycles to failure for nanophased sandwich was significantly higher than that of the neat ones. For example, at 57% of ultimate shear strength, nanophased sandwich would survive 400,000 cycles more than its neat counterpart. SEM micrographs indicated stronger cell structures with nanophased foams. These stronger cells strengthened the sub-interface zones underneath the actual core-skin interface. High toughness of the sub-interface layer delayed initiation of fatigue cracks and thereby increased the fatigue life of nanophased sandwich composites.

  2. Critical velocity of sandwich cylindrical shell under moving internal pressure

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Critical velocity of an infinite long sandwich shell under moving internal pres-sure is studied using the sandwich shell theory and elastodynamics theory. Propagation of axisymmetric free harmonic waves in the sandwich shell is studied using the sandwich shell theory by considering compressibility and transverse shear deformation of the core, and transverse shear deformation of face sheets. Based on the elastodynamics theory, displacement components expanded by Legendre polynomials, and position-dependent elastic constants and densities are introduced into the equations of motion. Critical ve-locity is the minimum phase velocity on the desperation relation curve obtained by using the two methods. Numerical examples and the finite element (FE) simulations are pre-sented. The results show that the two critical velocities agree well with each other, and two desperation relation curves agree well with each other when the wave number κ is relatively small. However, two limit phase velocities approach to the shear wave velocities of the face sheet and the core respectively when k limits to infinite. The two methods are efficient in the investigation of wave propagation in a sandwich cylindrical shell when κ is relatively small. The critical velocity predicted in the FE simulations agrees with theoretical prediction.

  3. Experimental study on mechanical properties of aircraft honeycomb sandwich structures

    Directory of Open Access Journals (Sweden)

    Talebi Mazraehshahi H.

    2010-06-01

    Full Text Available Mechanical behaviour of sandwich panels under different conditions have been exprimentally studied in this research to increase the knowledge of aircraft sandwich panel structures and facilitate design criteria for aircraft structures. Tests were concentrated on the honeycomb sandwich structures under different loads including flexural, insert shear, flat wise tension and compression loads. Furthermore, effect of core density and face material on mechanical behavior of different samples were investigated and compared with analytical and FEM method. Effects of skin thickness on strength of honycomb sandwhich panels under shear pull out and moments have also been considerd in this study. According to this investigation, insert strength and flexural test under different load conditions is strongly affected by face thickness, but compression and tearoff (falt wise tensile properties of a sandwich panel depends on core material. The study concludes that the correlation between experimental results and the analytical predictions will enable the designer to predict the mechanical behaviour and strength of a sandwich beam; however, applied formula may lead engineers to unreliable results for shear modulus.

  4. A comparison of FRP-sandwich penetrating impact test methods

    Energy Technology Data Exchange (ETDEWEB)

    Hildebrand, M. [VTT Manufacturing Technology, Espoo (Finland). Maritime and Mechanical Engineering

    1996-12-31

    The main objective of this project is to identify the test methods which provide useful results for the different types of penetrating impacts occurring in sandwich structures. A series of penetrating impact tests on FRP-sandwich panels is performed using three different test methods and the results of the test methods are compared. The test methods used are the standardised method ISO 6603 and two non-standardised methods. The first non-standardised method uses a pyramid-shaped impactor instead of the cylindrical impactor used in the ISO 6603 method. In the second non-standardised method, the impact test is performed quasistatically using a cylindrical impactor. Possible stages of failure occurring in FRP-sandwich during a penetrating impact are illustrated. A comprehensive test method should be able to provoke various failure modes, as observed in impact failures of actual sandwich structures. The results obtained with the three test methods lead to a different ranking in impact strength of the panels. Hence, impact test results obtained with different test methods are not even qualitatively comparable. The pyramid-shaped impactor is able to generate clearly more failure modes than the cylindrical impactor in the ISO 6603 method. Therefore, it is considered to be of more practical value for determining the impact strength of PRP-sandwich structures. (orig.) (15 refs.)

  5. Thermal buckling analysis of truss-core sandwich plates

    Institute of Scientific and Technical Information of China (English)

    陈继伟; 刘咏泉; 刘伟; 苏先樾

    2013-01-01

    Truss-core sandwich plates have received much attention in virtue of the high values of strength-to-weight and stiffness-to-weight as well as the great ability of impulse-resistance recently. It is necessary to study the stability of sandwich panels under the influence of the thermal load. However, the sandwich plates are such complex three-dimensional (3D) systems that direct analytical solutions do not exist, and the finite element method (FEM) cannot represent the relationship between structural parameters and mechanical properties well. In this paper, an equivalent homogeneous continuous plate is idealized by obtaining the effective bending and transverse shear stiffness based on the characteristics of periodically distributed unit cells. The first order shear deformation theory for plates is used to derive the stability equation. The buckling temperature of a simply supported sandwich plate is given and verified by the FEM. The effect of related parameters on mechanical properties is investigated. The geometric parameters of the unit cell are optimized to attain the maximum buckling temperature. It is shown that the optimized sandwich plate can improve the resistance to thermal buckling significantly.

  6. Design of sandwich acoustic window for sonar domes

    Institute of Scientific and Technical Information of China (English)

    YU Mengsa; LI Dongsheng; GONG Li; XU Jian

    2005-01-01

    Aimed at the low noise design of sonar dome in ships, a method has been presented for calculating the sonar self noise of a simplified sonar dome consisting of sandwich acoustic window and parallel acoustic cavity, which is excited by stationary random pressure fluctuation of turbulence boundary layer, using temporal and spatial double Fourier transform and wavenumber-frequency spectrum analysis. After numerically analyzing the influence of geometrical and physical parameters of acoustic window on the sonar self noise, the design method and reasonable parameters for sandwich acoustic window are proposed. The results show that the property of low noise induced by acoustic window of sandwich is dominated by the cut-off effect of longitudinal wave and transverse wave propagating in the visco-elastic layer of sandwich as well as the mismatch effect of impedance. If the thickness, density, Young's modulus and damping factor of plates and visco-elastic layer as well as the sound speed of longitudinal wave and transverse wave in the visco-elastic layer are selected reasonably, the maximum noise reduction of sandwich acoustic window is 6.5 dB greater than that of a single glass fiber reinforced plastic plate.

  7. Measurements and Counts for Notacanthidae Specimens

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Taxonomic data were collected for specimens of deep-sea spiny eels (Notacanthidae) from the Hawaiian Ridge by Bruce C. Mundy. Specimens were collected off the north...

  8. Ham Sandwich with Mayo: A Stronger Conclusion to the Classical Ham Sandwich Theorem

    CERN Document Server

    Elton, John H

    2009-01-01

    The conclusion of the classical ham sandwich theorem of Banach and Steinhaus may be strengthened: there always exists a common bisecting hyperplane that touches each of the sets, that is, intersects the closure of each set. Hence, if the knife is smeared with mayonnaise, a cut can always be made so that it will not only simultaneously bisect each of the ingredients, but it will also spread mayonnaise on each. A discrete analog of this theorem says that n finite nonempty sets in n-dimensional Euclidean space can always be simultaneously bisected by a single hyperplane that contains at least one point in each set. More generally, for n compactly-supported positive finite Borel measures in Euclidean n-space, there is always a hyperplane that bisects each of the measures and intersects the support of each measure.

  9. 1/3 SUBHARMONIC SOLUTION OF ELLIPTICAL SANDWICH PLATES

    Institute of Scientific and Technical Information of China (English)

    李银山; 张年梅; 杨桂通

    2003-01-01

    The problem of nonlinear forced oscillations for elliptical sandwich plates is dealtwith. Based on the governing equations expressed in terms of five displacement components,the nonlinear dynamic equation of an elliptical sandwich plate under a harmonic force isderived. A superpositive-iterative harmonic balance ( SIHB ) method is presented for thesteady-state analysis of strongly nonlinear oscillators. In a periodic oscillation, the periodicsolutions can be expressed in the form of basic harmonics and bifurcate harmonics. Thus,an oscillation system which is described as a second order ordinary differential equation,can be expressed as fundamental differential equation with fundamental harmonics andincremental differential equation with derived harmonics. The 1/3 subharnonic solution ofan elliptical sandwich plate is investigated by using the methods of SIHB. The SIHB methodis compared with the numerical integration method. Finally, asymptotical stability of the1/3 subharmonic oscillations is inspected.

  10. Sandwich complex-containing macromolecules: property tunability through versatile synthesis.

    Science.gov (United States)

    Abd-El-Aziz, Alaa S; Agatemor, Christian; Etkin, Nola

    2014-03-01

    Sandwich complexes feature unique properties as the physical and electronic properties of a hydrocarbon ligand or its derivative are integrated into the physical, electronic, magnetic, and optical properties of a metal. Incorporation of these complexes into macromolecules results in intriguing physical, electrical, and optical properties that were hitherto unknown in organic-based macromolecules. These properties are tunable through well-designed synthetic strategies. This review surveys many of the synthetic approaches that have resulted in tuning the properties of sandwich complex-containing macromolecules. While the past two decades have seen an ever-growing number of research publications in this field, gaps remain to be filled. Thus, we expect this review to stimulate research interest towards bridging these gaps, which include the insolubility of some of these macromolecules as well as expanding the scope of the sandwich complexes. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Identification of material properties of sandwich structure with piezoelectric patches

    Directory of Open Access Journals (Sweden)

    Zemčík R.

    2008-11-01

    Full Text Available The work focuses on light-weight sandwich structures made of carbon-epoxy skins and foam core which have unique bending stiffness compared to conventional materials. The skins are manufactured by vacuum autoclave technology from unidirectional prepregs and the sandwich is then glued together. The resulting material properties of the structure usually differ from those provided by manufacturer or even those obtained from experimental tests on separate materials, which makes computational models unreliable. Therefore, the properties are identified using the combination of experimental analysis of the sandwich with attached piezoelectric transducer and corresponding static and modal finite element analyses. Simple mathematical optimization with repetitive finite element solution is used. The model is then verified by transient analysis when the piezoelectric patch is excited by harmonic signals covering the first two eigen-frequencies and the induced oscillations are measured by laser sensor.

  12. Microtomography with sandwich detectors for small-animal bone imaging

    Science.gov (United States)

    Kim, S. H.; Kim, D. W.; Kim, D.; Youn, H.; Cho, S.; Kim, H. K.

    2016-10-01

    An x-ray radiographic system consisting of two detectors in tandem, or a sandwich detector, can produce dual-energy image from a single-shot exposure. Subtraction of two images obtained from the two detectors can produce a sharper image through an unsharp masking effect if the two images are formed at different spatial resolutions. This is indeed possible by incorporating different thicknesses of x-ray conversion layers in the detectors. In this study, we have developed a microtomography system with a sandwich detector in pursuit of high-resolution bone-enhanced small-animal imaging. The results show that the bone-enhanced images reconstructed from the dual-energy projection data provide higher visibility of bone details than the conventionally reconstructed images. The microtomography with the single-shot dual-energy sandwich detector will be useful for the high-resolution bone-enhanced small-animal imaging.

  13. Free vibration Analysis of Sandwich Plates with cutout

    Science.gov (United States)

    Mishra, N.; Basa, B.; Sarangi, S. K.

    2016-09-01

    This paper presents the free vibration analysis of sandwich plates with cutouts. Cutouts are inevitable in structural applications and the presence of these cutouts in the structures greatly influences their dynamic characteristics. A finite element model has been developed here using the ANSYS 15.0 software to study the free vibration characteristics of sandwich plates in the presence of cutouts. Shell 281 element, an 8-noded element with six degrees of freedom suited for analyzing thin to moderately thick structures is considered in the development of the model. Block Lanczose method is adopted to extract the mode shapes to obtain the natural frequency corresponding to free vibration of the plate. The effects of parametric variation on the natural frequency of the sandwich plates with cutout are studied and results are presented.

  14. ANALISIS KERAGAAN PANEL SANDWICH UNTUK RUMAH PRA-PABRIKASI

    Directory of Open Access Journals (Sweden)

    Naresworo Nugroho

    2010-12-01

    Full Text Available In the last five years, several earthquakes struck several places in Indonesia and thousands of people died caused of their masonry house. Therefore, the idea of bamboo utilization in the form of structural sandwich panel components for anti-seismic pre-fabrication house is one of appropriate way out. This research describes the performance and behavior of engineered structure wooden-bamboo sandwich panel in full sized test. The wall frame being use were meranti wood, this frame attached by plywood as face and back, then 5 cm bamboo cutting as core; the fastener used in this study were isocyanate resin and nails. This study carried out by experimental data of full scale structural tests on shear wall (ISO 22452. These result showed that the seismic reliability of the wall frame system made of bamboo sandwich panel was appropriate and will be useful for pre-fabrication houses as anti-seismic and environment friendly residential building

  15. Study on voids of epoxy matrix composites sandwich structure parts

    Science.gov (United States)

    He, Simin; Wen, Youyi; Yu, Wenjun; Liu, Hong; Yue, Cheng; Bao, Jing

    2017-03-01

    Void is the most common tiny defect of composite materials. Porosity is closely related to composite structure property. The voids forming behaviour in the composites sandwich structural parts with the carbon fiber reinforced epoxy resin skins was researched by adjusting the manufacturing process parameters. The composites laminate with different porosities were prepared with the different process parameter. The ultrasonic non-destructive measurement method for the porosity was developed and verified through microscopic examination. The analysis results show that compaction pressure during the manufacturing process had influence on the porosity in the laminate area. Increasing the compaction pressure and compaction time will reduce the porosity of the laminates. The bond-line between honeycomb core and carbon fiber reinforced epoxy resin skins were also analyzed through microscopic examination. The mechanical properties of sandwich structure composites were studied. The optimization process parameters and porosity ultrasonic measurement method for composites sandwich structure have been applied to the production of the composite parts.

  16. Examination of Sandwich Materials Using Air-Coupled Ultrasonics

    DEFF Research Database (Denmark)

    Borum, K.K.; Berggreen, Carl Christian

    2004-01-01

    The air-coupled ultrasonic techniques have been improved drastically in recent years. Better equipment has made this technique much more useful. This paper focuses on the examination of sandwich materials used in naval ships. It is more convenient to be able to make the measurements directly...... in atmospheric air instead of using immersion technique. The air-coupled techniques have been used in through-transmission mode using separate sender and receiver transducer. The frequency was either 50 kHz or 120 kHz. Laboratory tests on glass fibre/PVC foam core sandwich panels showed that debonds between core...... and skin laminate could be found by the air-coupled technique. It was therefore decided to use this technique in-situ during mechanical testing of sandwich panels. These tests were done in order to verify a developed FEM code using interfacial fracture mechanics and illustrated on a superstructure...

  17. Effect of layer length on deflection in sandwich beams

    Science.gov (United States)

    Abbu, Muthanna A.; AL-Ameri, Riyadh

    2017-09-01

    A theoretical study has been carried out on sandwich beams strengthened mechanically by two external steel plates attached to their tension and compression sides with so-called "shear connectors ". This study is based on the individual behaviour of each component of the composite sandwich section (i.e. reinforced concrete beam and upper steel plate and lower steel plate). The approach has been developed to simulate the behaviour of such beams, and is based on neglecting the separation between the three layers; i.e., the deflections are equal in each element through the same section. The differential equations reached were solved analytically. Deflection was calculated by using the approach for several beams, tested in two series, and close agreements were obtained with the experimental values. Furthermore, the interaction efficiency between the three elements in a composite sandwich beam has been considered thoroughly, from which the effect of some parameters, such as plate length upon the behaviour of such beams, were studied.

  18. Vibration analysis and optimization of sandwich composite with curvilinear fibers

    Science.gov (United States)

    Honda, S.; Narita, Y.

    2016-09-01

    The present paper develops a shell element based on the refined zigzag theory (RZT) and applies it to the vibration analysis and optimization problem of the composite sandwich plate composed of CFRP skins and soft-cores. The RZT accepts large differences in layer stiffness, and requires less calculation effort than the layer-wise or three-dimensional theories. Numerical results revealed that the present method predicts vibration characteristics of composite sandwich plates with soft-core accurately. Then, shapes of reinforcing fibers in CFRP composite skins are optimized to maximize fundamental frequencies. As an optimizer, the particle swarm optimization (PSO) approach is employed since curvilinear fiber shapes are defined by continuous design variables. Obtained results showed that the composite sandwich with optimum curvilinear fiber shapes indicates higher fundamental frequencies compared with straight fibers.

  19. ['Sandwich PhD': considerations for a successful experience abroad].

    Science.gov (United States)

    Salvetti, Marina de Goes; Bueno, Mariana; Gastaldo, Denise; Kimura, Amélia Fumiko; Pimenta, Cibele Andrucioli de Mattos

    2013-03-01

    International PhD internship, named "Sandwich PhD" in Brazil is an opportunity to improve research abilities, to become known in academic area and to establish and/or increase work opportunities in an international context. In this article, we describe key factors regarding the planning and development of the "Sandwich PhD" as experienced by professors and students involved in the collaboration between the School of Nursing, University of São Paulo and Lawrence S. Bloomberg Faculty of Nursing, University of Toronto, Canada. We also present the participation of PhD students' network as an alternative to the "Sandwich PhD". An international experience, when well-planned and developed correctly, promotes students' personal and professional development and favors the internationalization of Brazilian graduate programs and research groups.

  20. Extended high order sandwich panel theory for bending analysis of sandwich beams with carbon nanotube reinforced face sheets

    Science.gov (United States)

    Jedari Salami, S.

    2016-02-01

    Bending analysis of a sandwich beam with soft core and carbon nanotube reinforced composite (CNTRC) face sheets in the literature is presented based on Extended High order Sandwich Panel Theory (EHSAPT). Distribution of fibers through the thickness of the face sheets could be uniform or functionally graded (FG). In this theory the face sheets follow the first order shear deformation theory (FSDT). Besides, the two dimensional elasticity is used for the core. The field equations are derived via the Ritz based solution which is suitable for any essential boundary condition. The influences of boundary conditions on bending response of the sandwich panel with soft core and CNTRC face sheet are investigated. In each type of boundary condition the effect of distribution pattern of CNTRCs on many essential involved parameters of the sandwich beam with functionally graded carbon nanotube reinforced composite (FG- CNTRC) face sheets are studied in detail. Finally, experimental result have been compared with those obtained based on developed solution method. It is concluded that, the sandwich beam with X distribution figure of face sheets is the strongest with the smallest transverse displacement, and followed by the UD, O and ∧-ones, respectively.

  1. Methods for Using Durable Adhesively Bonded Joints for Sandwich Structures

    Science.gov (United States)

    Smeltzer, Stanley S., III (Inventor); Lundgren, Eric C. (Inventor)

    2016-01-01

    Systems, methods, and apparatus for increasing durability of adhesively bonded joints in a sandwich structure. Such systems, methods, and apparatus includes an first face sheet and an second face sheet as well as an insert structure, the insert structure having a first insert face sheet, a second insert face sheet, and an insert core material. In addition, sandwich core material is arranged between the first face sheet and the second face sheet. A primary bondline may be coupled to the face sheet(s) and the splice. Further, systems, methods, and apparatus of the present disclosure advantageously reduce the load, provide a redundant path, reduce structural fatigue, and/or increase fatigue life.

  2. NONLINEAR VIBRATION OF CIRCULAR SANDWICH PLATES UNDER CIRCUMJACENT LOAD

    Institute of Scientific and Technical Information of China (English)

    DU Guo-jun; MA Jian-qing

    2006-01-01

    Based on yon Karman plate theory, the issue about nonlinear vibration for circular sandwich plates under circumjacent load with the loosely clamped boundary condition was researched. Nonlinear differential eigenvalue equations and boundary conditions of the problem were formulated by variational method and then their exact static solution can be got. The solution was derived by modified iteration method, so the anslytic relations between amplitude and nonlinear oscillating frequency for circular sandwich plates were obtained. When circumjacent load makes the lowest natural frequency zero,critical load is obtained.

  3. Electronic States in Quasi-one-Dimensional Copolymeric Sandwich Structures

    Institute of Scientific and Technical Information of China (English)

    刘德胜; 王鹿霞; 魏建华; 郑斌; 解士杰; 韩圣浩; 梅良模

    2001-01-01

    The electronic properties of xPA/nPPP/yPA sandwiched copo]ymers with a well-barrier-well structure have been studied by using a tight-binding calculation. It was found that the electronic properties of the neutral states of these sandwiched copolymers are sensitive to the constitutions of PPP and PA monomers and the interface coupling between PA and PPP. It is verified that the quantum tunnelling effect will occur at the lowest conductive state of xPA/nPPP/xPA copolymers.

  4. A New Silicon-Based Ferroelectric Sandwich Structure

    Institute of Scientific and Technical Information of China (English)

    任天令; 张林涛; 刘理天; 李志坚

    2001-01-01

    A new silicon-based PbTiO3/Pb(Zr0.53 Ti0.47)O3/PbTiO3 sandwich structure is fabricated by a sol-gel method. Compared with other fabrication processes without PbTiO3 buffer layers, the annealing temperature is greatly reduced by as much as 100℃. Capacitance-voltage, polarization-electric field and dielectric-frequency properties of this sandwich structure are studied. The Pb(Zrx Ti1-x)O3 films are proved to have good dielectric and ferroelectric properties.

  5. New-sandwiched hydrogen separation membranes with low environmental impact

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Y.; Ozaki, T.; Komaki, M.; Nishimura, C. [Eco-Energy Materials Group, Ecomaterials Center, Ibaraki (Japan)

    2003-07-01

    There is a strong interest in economical methods for hydrogen separation. In this work, we have developed sandwiched membranes, Pd-Ag/V-15Ni/Pd-Ag, which had much lower environmental impact than palladium-based membranes, which are the most commonly used membrane for the current production of highly pure hydrogen. The Pd-Ag overlayer was prepared on V-15Ni substrates (thickness 40 {mu}m) using multi-target sputtering. The hydrogen permeation of the Pd-Ag/V-15Ni/Pd-Ag sandwiched membranes was examined using gas permeation technology. (orig.)

  6. Friction stir welding (FSW of aluminium foam sandwich panels

    Directory of Open Access Journals (Sweden)

    M. Bušić

    2016-07-01

    Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

  7. Buckling analysis of sandwich plate using layer wise theory

    Energy Technology Data Exchange (ETDEWEB)

    Ranjbaran, Arash; Khoshravan, Mohammad Reza [University of Tabriz, Tabriz (Iran, Islamic Republic of); Kharazi, Mahsa [Sahand University of Technology, Sahand (Iran, Islamic Republic of)

    2014-07-15

    Buckling analysis of sandwich plate was investigated using layer wise method. The formulation was based on the first-order shear deformation theory, and the Rayleigh-Ritz method was used for approximating and determining the displacement field. The results obtained from layer wise theory was compared with finite element results and showed good agreement. This study demonstrated that layer wise theory could describe buckling behavior of sandwich plates with high accuracy and represents a more realistic and acceptable description of behavior of the plates with much less computational cost.

  8. Damage assessment of compression loaded debond damaged sandwich panels

    DEFF Research Database (Denmark)

    Moslemian, Ramin; Berggreen, Christian; Quispitupa, Amilcar;

    2010-01-01

    Sandwich composites with face sheets of fiber-reinforced plastics (FRP) and cores of polymer foam offer a lightweight construction that is well suited to wind turbine blades, naval and other vessels for high-speed operation or where payload considerations require that the structural weight...... with an implanted circular face/core debond. Compression tests were conducted on intact sandwich panels and panels with an implanted circular face/core debond with three different types of foam core materials (PVC H130, PVC H250 and PMI 51-IG). The strains and out-of-plane displacements of the debonded region were...

  9. Fabrication and characterization of sandwiched optical fibers with periodic gratings.

    Science.gov (United States)

    Chiang, Chia-Chin

    2010-08-01

    This study proposes a novel process for fabricating a sandwiched long-period fiber grating (SLPFG) using a SU-8 thick photoresist technique. The SLPFG consists of a thin cladding optical fiber sandwiched with a double-sided periodical grating coating. By varying the external loads on the SLPFG, the transmission dip of the resonance wavelength is tuned according to a squared-harmonic curve. The SLPFG can thus be utilized as a loss tunable filter or sensor. The resonance dip wavelength is related to the cladding thicknesses of the optical fiber and the periods of the grating. A maximum transmission resonant dip of 34.61dB was achieved.

  10. The application of J integral to measure cohesive laws in materials undergoing large scale yielding

    DEFF Research Database (Denmark)

    Sørensen, Bent F.; Goutianos, Stergios

    2015-01-01

    We explore the possibility of determining cohesive laws by the J-integral approach for materials having non-linear stress-strain behaviour (e.g. polymers and composites) by the use of a DCB sandwich specimen, consisting of stiff elastic beams bonded to the non-linear test material, loaded with pure...... bending moments. For a wide range of parameters of the non-linear material, the plastic unloading during crack extension is small, resulting in J integral values (fracture resistance) that deviate maximum 15% from the work of the cohesive traction. Thus the method can be used to extract the cohesive laws...... directly from experiments without any presumption about their shape. Finally, the DCB sandwich specimen was also analysed using the I integral to quantify the overestimation of the steady-state fracture resistance obtained using the J integral based method....

  11. Composite Behavior of Insulated Concrete Sandwich Wall Panels Subjected to Wind Pressure and Suction

    Directory of Open Access Journals (Sweden)

    Insub Choi

    2015-03-01

    Full Text Available A full-scale experimental test was conducted to analyze the composite behavior of insulated concrete sandwich wall panels (ICSWPs subjected to wind pressure and suction. The experimental program was composed of three groups of ICSWP specimens, each with a different type of insulation and number of glass-fiber-reinforced polymer (GFRP shear grids. The degree of composite action of each specimen was analyzed according to the load direction, type of the insulation, and number of GFRP shear grids by comparing the theoretical and experimental values. The failure modes of the ICSWPs were compared to investigate the effect of bonds according to the load direction and type of insulation. Bonds based on insulation absorptiveness were effective to result in the composite behavior of ICSWP under positive loading tests only, while bonds based on insulation surface roughness were effective under both positive and negative loading tests. Therefore, the composite behavior based on surface roughness can be applied to the calculation of the design strength of ICSWPs with continuous GFRP shear connectors.

  12. Composite Behavior of Insulated Concrete Sandwich Wall Panels Subjected to Wind Pressure and Suction

    Science.gov (United States)

    Choi, Insub; Kim, JunHee; Kim, Ho-Ryong

    2015-01-01

    A full-scale experimental test was conducted to analyze the composite behavior of insulated concrete sandwich wall panels (ICSWPs) subjected to wind pressure and suction. The experimental program was composed of three groups of ICSWP specimens, each with a different type of insulation and number of glass-fiber-reinforced polymer (GFRP) shear grids. The degree of composite action of each specimen was analyzed according to the load direction, type of the insulation, and number of GFRP shear grids by comparing the theoretical and experimental values. The failure modes of the ICSWPs were compared to investigate the effect of bonds according to the load direction and type of insulation. Bonds based on insulation absorptiveness were effective to result in the composite behavior of ICSWP under positive loading tests only, while bonds based on insulation surface roughness were effective under both positive and negative loading tests. Therefore, the composite behavior based on surface roughness can be applied to the calculation of the design strength of ICSWPs with continuous GFRP shear connectors. PMID:28788001

  13. Comparisons of SHM Sensor Models with Empirical Test Data for Sandwich Composite Structures

    Science.gov (United States)

    2011-09-01

    propagation in a honeycomb sandwich panel was done by Metis Design Inc. in collaboration with ARC NASA . The sandwich panel fabricated for this test...structures. Sandwich type composites are being studied for use in NASAs new heavy lift launch vehicle and flaw detection is crucial for safety and for...and at the Marshall Space Flight Center to examine acoustic wave propagating and the ability to detect intrinsic faults in sandwich type composite

  14. Stabilization of nonlinear sandwich systems via state feedback-Discrete-time systems

    NARCIS (Netherlands)

    Wang, Xu; Stoorvogel, Anton A.; Saberi, Ali; Grip, H°avard Fjær; Sannuti, Peddapullaiah

    2011-01-01

    A recent paper (IEEE Trans. Aut. Contr. 2010; 55(9):2156–2160) considered stabilization of a class of continuous-time nonlinear sandwich systems via state feedback. This paper is a discrete-time counterpart of it. The class of nonlinear sandwich systems consists of saturation elements sandwiched bet

  15. Study of compression-loaded and impact-damaged structurally efficient graphite-thermoplastic trapezoidal-corrugation sandwich and semisandwich panels

    Science.gov (United States)

    Jegley, Dawn C.

    1992-01-01

    The structural efficiency of compression-loaded trapezoidal-corrugation sandwich and semisandwich composite panels is studied to determine their weight savings potential. Sandwich panels with two identical face sheets and a trapezoidal corrugated core between them and semisandwich panels with a corrugation attached to a single skin are considered. An optimization code is used to find the minimum weight designs for critical compressive load levels ranging from 3000 to 24,000 lb/in. Graphite-thermoplastic panels based on the optimal minimum weight designs were fabricated and tested. A finite element analysis of several test specimens was also conducted. The results of the optimization study, the finite element analysis, and the experiments are presented. The results of testing impact damage panels are also discussed.

  16. Clinicopathological study of hysterectomised specimens

    Directory of Open Access Journals (Sweden)

    Saravana A.

    2016-12-01

    Full Text Available Background: Hysterectomy is the commonest major surgical procedure performed in gynecology. It can be done by abdominal or vaginal route and with the help of laparoscopy. Hysterectomy is an effective treatment option for many conditions like fibroid, abnormal uterine bleeding, endometriosis, adenomyosis, uterine prolapse, pelvic inflammatory disease and cancer of reproductive organ when other treatment options are contraindicated or have failed, or if the woman no longer wishes to retain her menstrual and reproductive. The aim and objective of the study was to correlate indications of hysterectomy with histopathological findings in hysterectomised patients. Methods: A retrospective study was carried on 113 hysterectomised cases over a period of one year from June 2015 to May 2016. The data regarding the patient’s age, parity, clinical diagnosis, type of hysterectomy and histopathological diagnosis were reviewed by the records and analyzed. Results: A total of 113 cases of hysterectomies were studied. Hysterectomies were distributed over a wide age ranging from 20 years to 75 years. Most common age group was 41-50 years. Among hystectomies majority were done through vaginal route 86 (76.1% and 26 (23% cases were done through abdominal route. Most common clinical diagnosis was fibroid uterus in 44(38.9% cases. Most of the hysterectomies were done for benign conditions. In final histopathological report most common diagnosis was fibroid uterus in 45(39.8% hysterectomy specimens. It was correlated well with clinical diagnosis. Next most common histopathological diagnosis was Adenomyosis. Conclusions: Histopathological analysis correlated well with preoperative clinical diagnosis in majority of cases. The commonest indication and histopathological finding in our study was fibroid uterus. Next most common histopathological finding was Adenomyosis. Most commonly hysterectomies were done through vaginal route in our study.

  17. [The German Environmental Specimen Bank].

    Science.gov (United States)

    Schröter-Kermani, Christa; Gies, Andreas; Kolossa-Gehring, Marike

    2016-03-01

    The main objective of the German Environmental Specimen Bank (ESB) is the long-term storage of environmental and human samples under stable deep-freeze conditions for future research. The ESB is unique in providing a continuous historical record of environmental and human exposure to chemicals in Germany. ESB was started parallel to the development of the first German Chemicals Legislation in the late 1970s. In 1979, the ESB test operation began. After the Chemicals Law came into force in 1982, the ESB was established as a permanent facility in 1985. With the new European Chemicals Legislation, REACH, in 2007 responsibility for the safety of commercial chemicals and risk assessment was assigned to the industry. Since then, the ESB has become even more important in verifying the self-assessment of the industry, in evaluating the effectiveness of regulations, thus ensuring the protection of humans and the environment against adverse effects caused by exposure to chemicals. These objectives are pursued by the regular monitoring of contaminations and the assessment of temporal trends. Demonstrating the necessity of deriving exposure reduction measures, ESB results serve as key information for policy-makers. Information on preventing exposure to chemicals is available to the general public and to the public health services. The ESB is thus an important monitoring instrument of the Federal Ministry for the Environment, Nature Conservation, Building and Nuclear Safety. The Federal Environment Agency operates the ESB based on its own concepts, heads the scientific data evaluation and transfers results into the environmental policy arena and to the general public.

  18. Composite Behavior of a Novel Insulated Concrete Sandwich Wall Panel Reinforced with GFRP Shear Grids: Effects of Insulation Types

    Directory of Open Access Journals (Sweden)

    JunHee Kim

    2015-03-01

    Full Text Available A full-scale experimental program was used in this study to investigate the structural behavior of novel insulated concrete sandwich wall panels (SWPs reinforced with grid-type glass-fiber-reinforced polymer (GFRP shear connectors. Two kinds of insulation-expanded polystyrene (EPS and extruded polystyrene (XPS with 100 mm thickness were incased between the two concrete wythes to meet the increasing demand for the insulation performance of building envelope. One to four GFRP shear grids were used to examine the degree of composite action of the two concrete wythes. Ten specimens of SWPs were tested under displacement control subjected to four-point concentrated loads. The test results showed that the SWPs reinforced with GFRP grids as shear connectors developed a high degree of composite action resulting in high flexural strength. The specimens with EPS foam exhibited an enhanced load-displacement behavior compared with the specimens with XPS because of the relatively stronger bond between insulation and concrete. In addition, the ultimate strength of the test results was compared to the analytical prediction with the mechanical properties of only GRFP grids. The specimens with EPS insulation presented higher strength-based composite action than the ones with XPS insulation.

  19. A Study for the Characteristic Changes Under the Repeated Thermal Exposure in the Process of Repairing Aircraft Sandwich Structures

    Science.gov (United States)

    Kim, Yun Hae; Han, Joong Won; Kim, Don Won; Choi, Byung Keun; Murakami, R.

    Delamination can be observed in the sound areas during and/or after a couple times exposure to the elevated curing temperature due to the repeated repair condition. This study was conducted for checking the degree of degradation of properties of the cured parts and delamination between skin prepreg and honeycomb core. Specimens with glass honeycomb sandwich construction and glass/epoxy prepreg were prepared. The specimens were cured 1 to 5 times at 260°F in an autoclave and each additionally exposed 50, 100 and 150 hours in the 260°F oven. Each specimen was tested for tensile strength, compressive strength, flatwise tensile strength and interlaminar shear strength. To monitor the characteristics of the resin itself, the cured resin was tested using DMA and DSC. As a results, the decrease of Tg value were observed in the specific specimen which is exposed over 50 hrs at 260°F. This means the change or degradative of resin properties is also related to the decrease of flatwise tensile properties. Accordingly, minimal exposure on the curing temperature is recommended for parts in order to prevent the delation and maintain the better condition.

  20. Stiff, Strong Splice For A Composite Sandwich Structure

    Science.gov (United States)

    Schmaling, D.

    1991-01-01

    New type of splice for composite sandwich structure reduces peak shear stress in structure. Layers of alternating fiber orientation interposed between thin ears in adhesive joint. Developed for structural joint in spar of helicopter rotor blade, increases precision of control over thickness of adhesive at joint. Joint easy to make, requires no additional pieces, and adds little weight.

  1. Bending and Deformation of Sandwich Panels Due to Localized Pressure

    Directory of Open Access Journals (Sweden)

    Bambang K. Hadi

    2005-05-01

    Full Text Available Bending and deformation of sandwich panels due to localized pressure were analyzed using both Rayleigh-Ritz and finite element methods. The faces were made of laminated composite plates, while the core was a honeycomb material. Carbon fiber and glass fiber reinforced plastics were used for composite plate faces. In the case of Rayleigh-Ritz method, first the total energy of the system was calculated and then taking the variations of the total energy, the sandwich panel deflections could be computed. The deflections were assumed by means of Fourier series. A finite element code NASTRAN was exploited extensively in the finite element method. 3-dimensional 8-node brick elements were used to model sandwich panels, for both the faces sheets and the core. The results were then compared to each other and in general they are in good agreements. Dimple phenomena were found in these cases. It shows that localized pressure on sandwich structures will produce dimple on the pressurize region with little effects on the rest of the structures.

  2. Mechanical Behavior of CFRP Lattice Core Sandwich Bolted Corner Joints

    Science.gov (United States)

    Zhu, Xiaolei; Liu, Yang; Wang, Yana; Lu, Xiaofeng; Zhu, Lingxue

    2017-02-01

    The lattice core sandwich structures have drawn more attention for the integration of load capacity and multifunctional applications. However, the connection of carbon fibers reinforced polymer composite (CFRP) lattice core sandwich structure hinders its application. In this paper, a typical connection of two lattice core sandwich panels, named as corner joint or L-joint, was investigated by experiment and finite element method (FEM). The mechanical behavior and failure mode of the corner joints were discussed. The results showed that the main deformation pattern and failure mode of the lattice core sandwich bolted corner joints structure were the deformation of metal connector and indentation of the face sheet in the bolt holes. The metal connectors played an important role in bolted corner joints structure. In order to save the calculation resource, a continuum model of pyramid lattice core was used to replace the exact structure. The computation results were consistent with experiment, and the maximum error was 19%. The FEM demonstrated the deflection process of the bolted corner joints structure visually. So the simplified FEM can be used for further analysis of the bolted corner joints structure in engineering.

  3. Electronic transport in nanoparticle monolayers sandwiched between graphene electrodes.

    Science.gov (United States)

    Lu, Chenguang; Zhang, Datong; van der Zande, Arend; Kim, Philip; Herman, Irving P

    2014-11-06

    Graphene/CdSe nanoparticle monolayer/graphene sandwich structures were fabricated to explore the interactions between these layered materials. Electrical transport across these heterostructures suggests that transport is limited by tunneling through the nanoparticle (NP) ligands but not the NP core itself. Photoconductivity suggests ligands may affect the exciton separation efficiency.

  4. Elastic-plastic deformation of sandwich rod on elastic basis

    Institute of Scientific and Technical Information of China (English)

    GU Yu

    2008-01-01

    Sandwich composite material possesses advantages of both light weight and high strength.Although the mechanical behaviors of sandwich composite material with the influence of single external environment have been intensively studied,little work has been done in the study of mechanical property,in view of the nonlinear behavior of sandwich composites in the complicated external environments.In this paper,the problem about the bending of the three-layer elastic-plastic rod located on the elastic base,with a compressibly physical nonlinear core,has been studied.The mechanical response of the designed three-layer elements consisting of two bearing layers and a core has been examined.The complicated problem about curving of the three-layer rod located on the elastic base has been solved.The convergence of the proposed method of elastic solutions is examined to convince that the solution is acceptable.The calculated results indicate that the plasticity and physical nonlinearity of materials have a great influence on the deformation of the sandwich rod on the elastic basis.

  5. Editorial: Sandwiched Between Strasbourg and Karlsruhe: EU Fundamental Rights Protection

    NARCIS (Netherlands)

    Reestman, J.H.; Besselink, L.

    2016-01-01

    Starting out from the notion of the `Verfassungsgerichtsverbund´, coined by the President Vosskuhle of the German Federal Constitutional Court, this contribution sketches the manner in which the European Court of Justice operates, sandwiched in between the European Court of Human Rights that sets a

  6. Electrowetting-driven oscillating drops sandwiched between two substrates

    NARCIS (Netherlands)

    Mampallil, Dileep; Eral, H.B.; Staicu, A.D.; Mugele, F.; Ende, van den D.

    2013-01-01

    Drops sandwiched between two substrates are often found in lab-on-chip devices based on digital microfluidics. We excite azimuthal oscillations of such drops by periodically modulating the contact line via ac electrowetting. By tuning the frequency of the applied voltage, several shape modes can be

  7. Dielectrophoretic behaviours of microdroplet sandwiched between LN substrates.

    Science.gov (United States)

    Chen, Lipin; Li, Shaobei; Fan, Bolin; Yan, Wenbo; Wang, Donghui; Shi, Lihong; Chen, Hongjian; Ban, Dechao; Sun, Shihao

    2016-07-07

    We demonstrate a sandwich configuration for microfluidic manipulation in LiNbO3 platform based on photovoltaic effect, and the behaviours of dielectric microdroplet under this sandwich configuration are investigated. It is found that the microdroplet can generate in the form of liquid bridge inside the LiNbO3-based sandwich structure under the governing dielectrophoretic force, and the dynamic process of microdroplet generation highly depends on the substrate combinations. Dynamic features found for different combinations are explained by the different electrostatic field distribution basing on the finite-element simulation results. Moreover, the electrostatic field required by the microdroplet generation is estimated through meniscus evolution and it is found in good agreement with the simulated electrostatic field inside the sandwich gap. Several kinds of microdroplet manipulations are attempted in this work. We suggest that the local dielectrophoretic force acting on the microdroplet depends on the distribution of the accumulated irradiation dosage. Without using any additional pumping or jetting actuator, the microdroplet can be step-moved, deformed or patterned by the inconsecutive dot-irradiation scheme, as well as elastically stretched out and back or smoothly guided in a designed pass by the consecutive line-irradiation scheme.

  8. Application of Load Carrying Sandwich Elements in Wind Turbine Blades

    DEFF Research Database (Denmark)

    Jensen, Jacob Fisker; Schultz, Jacob Pagh; Berggreen, Carl Christian

    2005-01-01

    . For a single skin design, buckling is critical compared to other design criterions. By introducing sandwich, a significant weight reduction and increased buckling capacity is obtained. Tower clearance now becomes critical. Proper choice of core material and thickness is important to prevent face wrinkling...

  9. Effect of Physical Nonlinearity on Local Buckling in Sandwich Beams

    NARCIS (Netherlands)

    Koissin, Vitaly; Shipsha, Andrey; Skvortsov, Vitaly

    2010-01-01

    This article deals with experimental, theoretical, and FE characterization of the local buckling in foam-core sandwich beams. In the theoretical approach, this phenomena is considered in a periodic formulation (unbounded wrinkle wave); a nonlinear stress—strain response of the face material is accou

  10. Bending moment of galvanized iron glass fiber sandwich panel

    Directory of Open Access Journals (Sweden)

    Gurustal Somnath Swamy

    2016-05-01

    Full Text Available The main objective of this project is to prepare a laminated with Galvanized iron thickness fractions, fiber volume fractions and orientation in the layers of GF were fabricated by hand lay-up method and evaluated for their bending moment properties of the sandwich panel using universal testing machine. This paper theoretically calculates the bending behavior of sandwich panel. The recent need to develop a new range of materials has resulted in the development of high performance lightweight composites with excellent properties. Metal– composite systems consist of alternating layers of metal and fiber-reinforced polymer composites which are bonded by an adhesive. Sandwich beams were tested under Air Bending. Stress-strain and stress-displacement were recorded by using AIMIL UTM. The beam face sheets exhibited a softening non-linearity on the bending side. Experimental results were in good agreement with predictions from simple models. On an overall basis, the sandwich panel exhibited better bending moment performance than the monolithic galvanized iron

  11. The elastic response of sandwich structures to local loading

    NARCIS (Netherlands)

    Koysin, V.; Skvortsov, Vitaly; Krahmalev, Sergey; Shipsha, Andrey

    2004-01-01

    The paper addresses the elastic response of sandwich panels to local static and dynamic loading. The bottom face is assumed to be clamped, so that the overall bending is eliminated. The governing equations are derived using the static Lamé equations for the core and the thin plate Kirchoff–Love

  12. Multiscale Finite-Element Modeling of Sandwich Honeycomb Composite Structures

    Directory of Open Access Journals (Sweden)

    Yu. I. Dimitrienko

    2014-01-01

    Full Text Available The paper presents a developed multi-scale model of sandwich honeycomb structures. The model allows us both to calculate effective elastic-strength characteristics of honeycomb and forced covering of sandwich, and to find a 3D stress-strain state of structures using the threedimensional elastic theory for non- homogeneous media. On the basis of finite element analysis it is shown, that under four-point bending the maximal value of bending and shear stresses in the sandwich honeycomb structures are realized in the zone of applied force and plate support. Here the local stress maxima approximately 2-3 times exceed the “engineering” theoretical plate values of bending and shear stresses in the middle of panel. It is established that at tests for fourpoint bending there is a failure of the honeycomb sandwich panels because of the local adhesion failure rather than because of the covering exfoliation off the honeycomb core in the middle of panel.

  13. Fatigue failure of sandwich beams with face sheet wrinkle defects

    DEFF Research Database (Denmark)

    Leong, Martin Klitgaard; Hvejsel, C.F.; Thomsen, Ole Thybo

    2012-01-01

    This paper presents experimental fatigue results for GFRP face sheet/balsa core sandwich beams with face sheet wrinkle defects, subjected to fully reversed in-plane fatigue loading. An estimate of the fatigue design limit is presented, based on static test results, finite element analyses...

  14. Dielectrophoretic behaviours of microdroplet sandwiched between LN substrates

    Science.gov (United States)

    Chen, Lipin; Li, Shaobei; Fan, Bolin; Yan, Wenbo; Wang, Donghui; Shi, Lihong; Chen, Hongjian; Ban, Dechao; Sun, Shihao

    2016-07-01

    We demonstrate a sandwich configuration for microfluidic manipulation in LiNbO3 platform based on photovoltaic effect, and the behaviours of dielectric microdroplet under this sandwich configuration are investigated. It is found that the microdroplet can generate in the form of liquid bridge inside the LiNbO3-based sandwich structure under the governing dielectrophoretic force, and the dynamic process of microdroplet generation highly depends on the substrate combinations. Dynamic features found for different combinations are explained by the different electrostatic field distribution basing on the finite-element simulation results. Moreover, the electrostatic field required by the microdroplet generation is estimated through meniscus evolution and it is found in good agreement with the simulated electrostatic field inside the sandwich gap. Several kinds of microdroplet manipulations are attempted in this work. We suggest that the local dielectrophoretic force acting on the microdroplet depends on the distribution of the accumulated irradiation dosage. Without using any additional pumping or jetting actuator, the microdroplet can be step-moved, deformed or patterned by the inconsecutive dot-irradiation scheme, as well as elastically stretched out and back or smoothly guided in a designed pass by the consecutive line-irradiation scheme.

  15. Low-Velocity Impact on Composite Sandwich Plates

    Science.gov (United States)

    1996-07-01

    plate and correct for this error. 3.4 One- and Two-Degree of Freedom Models A single degree of freedom system (figure 3-3a) was used by Caprino et al...Composite Materials, Vol. 26, No. 10: 1523-1535 (1992). 211) Caprino , G., and Teti, R. "Impact and post-impact behavior of foam core sandwich

  16. Fluid Structure Interaction Effect on Sandwich Composite Structures

    Science.gov (United States)

    2011-09-01

    14. SUBJECT TERMS Fluid Structure Interaction, FSI, composite, balsa, low velocity impact, sandwich composites, VARTM , Vacuum Assisted Resin Transfer...11 1. Vacuum Assisted Resin Transfer Molding ( VARTM ) ...................11 2. Procedure...required equipment for VARTM composite production. ..............10 Figure 4. VARTM Lay-up (From [8

  17. Effect of microencapsulated phase change material in sandwich panels

    Energy Technology Data Exchange (ETDEWEB)

    Castellon, Cecilia; Medrano, Marc; Roca, Joan; Cabeza, Luisa F. [GREA Innovacio Concurrent, Edifici CREA, Universitat de Lleida, Pere de Cabrera s/n, 25001 Lleida (Spain); Navarro, Maria E.; Fernandez, Ana I. [Departamento de Ciencias de los Materiales e Ingenieria Metalurgica, Universitat de Barcelona, Marti i Franques 1, 08028 Barcelona (Spain); Lazaro, Ana; Zalba, Belen [Instituto de Investigacion en Ingenieria de Aragon, I3A, Grupo de Ingenieria Termica y Sistemas Energeticos (GITSE), Dpto. Ingenieria Mecanica, Area de Maquinas y Motores Termicos, Universidad de Zaragoza, Campus Politecnico Rio Ebro, Edificio ' ' Agustin de Betancourt,' ' Maria de Luna s/n, 50018 Zaragoza (Spain)

    2010-10-15

    Sandwich panels are a good option as building materials, as they offer excellent characteristics in a modular system. The goal of this study was to demonstrate the feasibility of using the microencapsulated PCM (Micronal BASF) in sandwich panels to increase their thermal inertia and to reduce the energy demand of the final buildings. In this paper, to manufacture the sandwich panel with microencapsulated PCM three different methods were tested. In case 1, the PCM was added mixing the microencapsulated PCM with one of the components of the polyurethane. In the other two cases, the PCM was added either a step before (case 2) or a step after (case 3) to the addition of the polyurethane to the metal sheets. The results show that in case 1 the effect of PCM was overlapped by a possible increase in thermal conductivity, but an increase of thermal inertia was found in case 3. In case 2, different results were obtained due to the poor distribution of the PCM. Some samples showed the effect of the PCM (higher thermal inertia), and other samples results were similar to the conventional sandwich panel. In both cases (2 and 3), it is required to industrialize the process to improve the results. (author)

  18. Dynamic Behaviour of Concrete Sandwich Panel under Blast Loading

    Directory of Open Access Journals (Sweden)

    Dong Yongxiang

    2009-01-01

    Full Text Available Surface contact explosion experiments were performed to study the dynamic behaviour of concrete sandwich panel subjected to blast loading. Experimental results have shown that there are four damage modes explosion cratering, scabbing of the backside, radial cracking induced failure, and circumferential cracking induced failure. It also illustrates that different foam materials sandwiched in the multi-layered medium have an important effect on damage patterns. Due to the foam material, the stress peak decreases one order of magnitude and the duration is more than four times that of the panel without the soft layer by numerical simulation. Additionally, the multi layered medium with concrete foam demonstrates the favourable protective property compared with that of aluminum foam. Meanwhile, the optimal analysis of the thickness of the foam material in the sandwich panel was performed in terms of experimental and numerical analyseis. The proper thickness proportion of soft layer is about 20 percent to the total thickness of sandwich panel under the conditions in this study.Defence Science Journal, 2009, 59(1, pp.22-29, DOI:http://dx.doi.org/10.14429/dsj.59.1480  

  19. Methods for Assessing Honeycomb Sandwich Panel Wrinkling Failures

    Science.gov (United States)

    Zalewski, Bart F.; Dial, William B.; Bednarcyk, Brett A.

    2012-01-01

    Efficient closed-form methods for predicting the facesheet wrinkling failure mode in sandwich panels are assessed. Comparisons were made with finite element model predictions for facesheet wrinkling, and a validated closed-form method was implemented in the HyperSizer structure sizing software.

  20. Flexural Strength of Functionally Graded Nanotube Reinforced Sandwich Spherical Panel

    Science.gov (United States)

    Mahapatra, Trupti R.; Mehar, Kulmani; Panda, Subrata K.; Dewangan, S.; Dash, Sushmita

    2017-02-01

    The flexural behaviour of the functionally graded sandwich spherical panel under uniform thermal environment has been investigated in the present work. The face sheets of the sandwich structure are made by the functionally graded carbon nanotube reinforced material and the core face is made by the isotropic and homogeneous material. The material properties of both the fiber and matrix are assumed to be temperature dependent. The sandwich panel model is developed in the framework of the first order shear deformation theory and the governing equation of motion is derived using the variational principle. For the discretization purpose a suitable shell element has been employed from the ANSYS library and the responses are computed using a parametric design language (APDL) coding. The performance and accuracy of the developed model has been established through the convergence and validation by comparing the obtained results with previously published results. Finally, the influence of different geometrical parameters and material properties on the flexural behaviour of the sandwich spherical panel in thermal environment has been investigated through various numerical illustrations and discussed in details.

  1. Effect of Physical Nonlinearity on Local Buckling in Sandwich Beams

    NARCIS (Netherlands)

    Koysin, V.; Shipsha, Andrey; Skvortsov, Vitaly

    2010-01-01

    This article deals with experimental, theoretical, and FE characterization of the local buckling in foam-core sandwich beams. In the theoretical approach, this phenomena is considered in a periodic formulation (unbounded wrinkle wave); a nonlinear stress—strain response of the face material is accou

  2. Modular container assembled from fiber reinforced thermoplastic sandwich panels

    Science.gov (United States)

    Donnelly, Mathew William; Kasoff, William Andrew; Mcculloch, Patrick Carl; Williams, Frederick Truman

    2007-12-25

    An improved, load bearing, modular design container structure assembled from thermoformed FRTP sandwich panels in which is utilized the unique core-skin edge configuration of the present invention in consideration of improved load bearing performance, improved useful load volume, reduced manufacturing costs, structural weight savings, impact and damage tolerance and repair and replace issues.

  3. Effect of acid etching of glass ionomer cement surface on the microleakage of sandwich restorations.

    Science.gov (United States)

    Bona, Alvaro Della; Pinzetta, Caroline; Rosa, Vinícius

    2007-06-01

    The purposes of this study were to evaluate the sealing ability of different glass ionomer cements (GICs) used for sandwich restorations and to assess the effect of acid etching of GIC on microleakage at GIC-resin composite interface. Forty cavities were prepared on the proximal surfaces of 20 permanent human premolars (2 cavities per tooth), assigned to 4 groups (n=10) and restored as follows: Group CIE - conventional GIC (CI) was applied onto the axial and cervical cavity walls, allowed setting for 5 min and acid etched (E) along the cavity margins with 35% phosphoric acid for 15 s, washed for 30 s and water was blotted; the adhesive system was applied and light cured for 10 s, completing the restoration with composite resin light cured for 40 s; Group CIN - same as Group CIE, except for acid etching of the CI surface; Group RME - same as CIE, but using a resin modified GIC (RMGIC); Group RMN - same as Group RME, except for acid etching of the RMGIC surface. Specimens were soaked in 1% methylene blue dye solution at 24 degrees C for 24 h, rinsed under running water for 1 h, bisected longitudinally and dye penetration was measured following the ISO/TS 11405-2003 standard. Results were statistically analyzed by Kruskal-Wallis and chi-square tests (a=0.05). Dye penetration scores were as follow: CIE - 2.5; CIN - 2.5; RME - 0.9; and RMN - 0.6. The results suggest that phosphoric acid etching of GIC prior to the placement of composite resin does not improve the sealing ability of sandwich restorations. The RMGIC was more effective in preventing dye penetration at the GIC-resin composite-dentin interfaces than CI.

  4. Effect of acid etching of glass ionomer cement surface on the microleakage of sandwich restorations

    Directory of Open Access Journals (Sweden)

    Álvaro Della Bona

    2007-06-01

    Full Text Available The purposes of this study were to evaluate the sealing ability of different glass ionomer cements (GICs used for sandwich restorations and to assess the effect of acid etching of GIC on microleakage at GIC-resin composite interface. Forty cavities were prepared on the proximal surfaces of 20 permanent human premolars (2 cavities per tooth, assigned to 4 groups (n=10 and restored as follows: Group CIE - conventional GIC (CI was applied onto the axial and cervical cavity walls, allowed setting for 5 min and acid etched (E along the cavity margins with 35% phosphoric acid for 15 s, washed for 30 s and water was blotted; the adhesive system was applied and light cured for 10 s, completing the restoration with composite resin light cured for 40 s; Group CIN - same as Group CIE, except for acid etching of the CI surface; Group RME - same as CIE, but using a resin modified GIC (RMGIC; Group RMN - same as Group RME, except for acid etching of the RMGIC surface. Specimens were soaked in 1% methylene blue dye solution at 24ºC for 24 h, rinsed under running water for 1 h, bisected longitudinally and dye penetration was measured following the ISO/TS 11405-2003 standard. Results were statistically analyzed by Kruskal-Wallis and chi-square tests (a=0.05. Dye penetration scores were as follow: CIE - 2.5; CIN - 2.5; RME - 0.9; and RMN - 0.6. The results suggest that phosphoric acid etching of GIC prior to the placement of composite resin does not improve the sealing ability of sandwich restorations. The RMGIC was more effective in preventing dye penetration at the GIC-resin composite-dentin interfaces than CI.

  5. An outbreak of Vero cytotoxin producing Escherichia coli O157 infection associated with takeaway sandwiches.

    LENUS (Irish Health Repository)

    McDonnell, R J

    1997-12-12

    An outbreak of food poisoning due to Escherichia coli O157 phage type 2 Vero cytotoxin 2 affected 26 people in southern counties of England in May and June 1995. The organism was isolated from faecal specimens from 23 patients, 16 of whom lived in Dorset and seven in Hampshire. Isolates were indistinguishable by phage typing, Vero cytotoxin gene typing, restriction fragment length polymorphism, and pulsed field gel electrophoresis. Three associated cases, linked epidemiologically to the outbreak, were confirmed serologically by detection of antibodies to E. coli O157 lipopolysaccharide. Twenty-two of the 26 patients were adults: four were admitted to hospital with haemorrhagic colitis. Four cases were children: two were admitted to hospital with haemolytic uraemic syndrome (HUS). There were no deaths. Although E. coli O157 was not isolated from any food samples, illness was associated with having eaten cold meats in sandwiches bought from two sandwich producers, in Weymouth and in Portsmouth. Both shops were supplied by the same wholesaler, who kept no records and obtained cooked meats from several sources in packs that did not carry adequate identification marks. It was, therefore, impossible to trace back to the original producer or to investigate further to determine the origin of contamination with E. coli O157. To protect the public health it is essential that all wholesale packs of ready-to-eat food carry date codes and the producer\\'s identification mark. Detailed record keeping should be part of hazard analysis critical control point (HACCP) systems and should be maintained throughout the chain of distribution from the producer to retail outlets.

  6. Full-field ultrasonic inspection for a composite sandwich plate skin-core debonding detection using laser-based ultrasonics

    Science.gov (United States)

    Chong, See Yenn; Victor, Jared J.; Todd, Michael D.

    2017-04-01

    In this paper, a full-field ultrasonic guided wave method is proposed to inspect a composite sandwich specimen made for an aircraft engine nacelle. The back skin/core interface of the specimen is built with two fabricated disbond defects (diameters of 12.7 mm and 25.4 mm) by removing areas of the adhesive used to bond the back skin to the core. A laser ultrasonic interrogation system (LUIS) incorporated with a disbond detection algorithm is developed. The system consists of a 1-kHz laser ultrasonic scanning system and a single fixed ultrasonic sensor to interrogate ultrasonic guided waves in the sandwich specimen. The interest area of 400 mm × 400 mm is scanned at a 0.5 mm scan interval. The corresponding full-field ultrasonic data is obtained and generated in the three-dimensional (3-D) space-time domain. Then, the 3-D full-field ultrasonic data is Fourier transformed and the ultrasonic frequency spectra are analyzed to determine the dominant frequency that is sensitive to the disbond defects. Continuous wavelet transform (CWT) based on fast Fourier transform (FFT) is implemented as a single-frequency bandpass filter to filter the full-field ultrasonic data in the 3-D space-time domain at the selected dominant frequency. The LUIS has shown the ability to detect the disbond with diameters of 11 mm and 23 mm which match to the pre-determined disbond sizes well. For future research, a robust signal processing algorithm and a model-based matched filter will be investigated to make the detection process autonomous and improve detectability

  7. Nondestructive DNA extraction from museum specimens.

    Science.gov (United States)

    Hofreiter, Michael

    2012-01-01

    Natural history museums around the world hold millions of animal and plant specimens that are potentially amenable to genetic analyses. With more and more populations and species becoming extinct, the importance of these specimens for phylogenetic and phylogeographic analyses is rapidly increasing. However, as most DNA extraction methods damage the specimens, nondestructive extraction methods are useful to balance the demands of molecular biologists, morphologists, and museum curators. Here, I describe a method for nondestructive DNA extraction from bony specimens (i.e., bones and teeth). In this method, the specimens are soaked in extraction buffer, and DNA is then purified from the soaking solution using adsorption to silica. The method reliably yields mitochondrial and often also nuclear DNA. The method has been adapted to DNA extraction from other types of specimens such as arthropods.

  8. Primary hepatocyte culture in collagen gel mixture and collagen sandwich

    Institute of Scientific and Technical Information of China (English)

    Ying-Jie Wang; Hong-Ling Liu; Hai-Tao Guo; Hong-Wei Wen; Jun Liu

    2004-01-01

    AIM: To explore the methods of hepatocytes culture in a collagen gel mixture or between double layers of collagen sandwich configuration and to examine the functional and cytomorphological characteristics of cultured hepatocytes.METHODS: A two-step collagenase perfusion technique was used to isolate the hepatocytes from Wistar rats or newborn Chinese experimental piglets. The isolated hepatocytes were cultured in a collagen gel mixture or between double layers of collagen sandwich configuration respectively. The former was that rat hepatocytes were mixed with type I rat tail collagen solution till gelled, and the medium was added onto the gel. The latter was that swine hepatocytes were seeded on a plate precoated with collagen gel for 24 h, then another layer of collagen gel was overlaid, resulting in a sandwich configuration. The cytomorphological characteristics, albumin secretion, and LDH-release of the hepatocytes cultured in these two models were examined.RESULTS: Freshly isolated rat hepatocytes were successfully mixed and fixed in collagen gel, and cultured in the gel condition. During the culture period, the urea synthesized and secreted by rat hepatocytes was detected throughout the period. Likewise, newborn experimental piglet hepatocytes were successfully fixed between the double layers of collagen gel, forming a sandwich configuration.Within a week of culture, the albumin secreted by swine hepatocytes was detected by SDS/PAGE analysis. The typical cytomorphological characteristics of the hepatocytes cultured by the above two culture models were found under a phasecontrast microscope. There was little LDH-release during the culture period.CONCLUSION: Both collagen gel mixture and double layers of collagen sandwich configuration can provide cultural conditions much closer to in vivoenvironment, and are helpful for maintaining specific hepatic fiJnctions and cytomorphological characteristics. A collagen gel mixture culture may be more eligible for the

  9. Cascaded-systems analysis of sandwich x-ray detectors

    Science.gov (United States)

    Kim, D. W.; Kim, J.; Yun, S.; Youn, H.; Kim, H. K.

    2016-12-01

    Active sandwich-like multilayer detectors have been developed, and their potential for motion-artifact-free dual-energy x-ray imaging at a single exposure has been demonstrated in the material decomposition context. Since the sandwich detector uses the x-ray beam transmittance through the front layer, direct x-ray interaction within photodiodes in the front layer is unavoidable, and which can increase noise in the front detector images. Similar direct x-ray interaction can also occur in the rear detector layer. To obtain a better contrast performance, an additional filter layer can be placed between the two detector layers. However, this filter layer can increase adversely noise in images obtained from the rear detector layer by reducing the number of x-ray photons reaching it. A theoretical model, which can describe the signal-to-noise performance of the sandwich detector as functions of various design parameters, has been developed by using a linear cascaded-systems theory. From the cascaded-systems analysis, the direct x-ray interaction increases noise at the high spatial frequencies where the number of secondary quanta lessens. The intermediate filter layer enhances the contribution of additive electronic noise in the overall noise performance of the rear detector layer. The detailed cascaded-systems analysis on the x-ray sandwich detectors are reported in comparisons with the measured noise-power spectra and detective quantum efficiencies. The developed model will be useful for a better design and practical use of a sandwich detector for single-shot dual-energy imaging.

  10. DCB - Cancer Immunology, Hematology, and Etiology Research

    Science.gov (United States)

    Part of NCI’s Division of Cancer Biology’s research portfolio, studies supported include the characterization of basic mechanisms relevant to anti-tumor immune responses and hematologic malignancies.

  11. DCB - DNA and Chromosome Aberrations Research

    Science.gov (United States)

    Part of NCI's Division of Cancer Biology's research portfolio, this research area is focused on making clear the genetic and epigenetic mechanisms of tumorigenesis and mechanisms of chemical and physical carcinogenesis.

  12. Making Durable Specimens For Electron Microscopy

    Science.gov (United States)

    Doychak, Joseph

    1989-01-01

    Consistent metal-oxide cross sections prepared quickly. New process makes TEM/STEM cross sections of metal/oxide interfaces. After specimen bars oxidized, placed in specially designed mold. Following encapsulation in zinc alloy, 3-mm-diameter specimen bar sliced into disks suitable for further preparation steps. Technique used to prepare 3-mm-diameter specimens of cross sections of oxides of alloys intended for use at temperatures greater than approximately 600 degree C.

  13. RSB: Research Specimen Banking across the Institution

    OpenAIRE

    Pense, Rick; Grose, Tim; Anderson, Lynn; Lee, H

    2001-01-01

    Research Specimen Banking (RSB) system is a component of the translational investigations infrastructure at Moffitt Cancer Center & Research Institute. It was implemented to provide specimen management functions to support basic science cancer research taking place in conjunction with caner clinical trials. RSB handles the receipt and distribution of clinical specimens to the research labs, with identifiers that both mask personal identity and enable linkage of clinical data to correlative re...

  14. The Planar Sandwich and Other 1D Planar Heat Flow Test Problems in ExactPack

    Energy Technology Data Exchange (ETDEWEB)

    Singleton, Jr., Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-01-24

    This report documents the implementation of several related 1D heat flow problems in the verification package ExactPack [1]. In particular, the planar sandwich class defined in Ref. [2], as well as the classes PlanarSandwichHot, PlanarSandwichHalf, and other generalizations of the planar sandwich problem, are defined and documented here. A rather general treatment of 1D heat flow is presented, whose main results have been implemented in the class Rod1D. All planar sandwich classes are derived from the parent class Rod1D.

  15. Mechanical Response of All-composite Pyramidal Lattice Truss Core Sandwich Structures

    Institute of Scientific and Technical Information of China (English)

    Ming Li; Linzhi Wu; Li Ma; Bing Wang; Zhengxi Guan

    2011-01-01

    The mechanical performance of an all-composite pyramidal lattice truss core sandwich structure was investigated both theoretically and experimentally. Sandwich structures were fabricated with a hot compression molding method using carbon fiber reinforced composite T700/3234. The out-of-plane compression and shear tests were conducted. Experimental results showed that the all-composite pyramidal lattice truss core sandwich structures were more weight efficient than other metallic lattice truss core sandwich structures. Failure modes revealed that node rupture dominated the mechanical behavior of sandwich structures.

  16. Elastic stability of superplastically formed/diffusion-bonded orthogonally corrugated core sandwich plates

    Science.gov (United States)

    Ko, W. L.

    1980-01-01

    The paper concerns the elastic buckling behavior of a newly developed superplastically formed/diffusion-bonded (SPF/DB) orthogonally corrugated core sandwich plate. Uniaxial buckling loads were calculated for this type of sandwich plate with simply supported edges by using orthotropic sandwich plate theory. The buckling behavior of this sandwich plate was then compared with that of an SPF/DB unidirectionally corrugated core sandwich plate under conditions of equal structural density. It was found that the buckling load for the former was considerably higher than that of the latter.

  17. STEM tomography for thick biological specimens

    Energy Technology Data Exchange (ETDEWEB)

    Aoyama, Kazuhiro [FEI Company Japan Ltd., Application Laboratory, NSS-II Building, 2-13-34 Kohnan, Minato-ku, Tokyo 108-0075 (Japan)], E-mail: kazuhiro.aoyama@fei.com; Takagi, Tomoko [FEI Company Japan Ltd., Application Laboratory, NSS-II Building, 2-13-34 Kohnan, Minato-ku, Tokyo 108-0075 (Japan); Laboratory of Electron Microscopy, Japan Women' s University, 2-8-1 Mejirodai, Bunkyo-ku, Tokyo 112-8681 (Japan); Hirase, Ai; Miyazawa, Atsuo [Bio-multisome Research Team, RIKEN SPring-8 Center, Harima Institute, 1-1-1 Kouto, Sayo, Hyogo 679-5148 (Japan); CREST, JST (Japan)

    2008-12-15

    Scanning transmission electron microscopy (STEM) tomography was applied to biological specimens such as yeast cells, HEK293 cells and primary culture neurons. These cells, which were embedded in a resin, were cut into 1-{mu}m-thick sections. STEM tomography offers several important advantages including: (1) it is effective even for thick specimens, (2) 'dynamic focusing', (3) ease of using an annular dark field (ADF) mode and (4) linear contrasts. It has become evident that STEM tomography offers significant advantages for the observation of thick specimens. By employing STEM tomography, even a 1-{mu}m-thick specimen (which is difficult to observe by conventional transmission electron microscopy (TEM)) was successfully analyzed in three dimensions. The specimen was tilted up to 73 deg. during data acquisition. At a large tilt angle, the specimen thicknesses increase dramatically. In order to observe such thick specimens, we introduced a special small condenser aperture that reduces the collection angle of the STEM probe. The specimen damage caused by the convergent electron beam was expected to be the most serious problem; however, the damage in STEM was actually smaller than that in TEM. In this study, the irradiation damage caused by TEM- and STEM-tomography in biological specimens was quantitatively compared.

  18. Compressive and shear buckling analysis of metal matrix composite sandwich panels under different thermal environments

    Science.gov (United States)

    Ko, William L.; Jackson, Raymond H.

    1993-01-01

    Combined inplane compressive and shear buckling analysis was conducted on flat rectangular sandwich panels using the Raleigh-Ritz minimum energy method with a consideration of transverse shear effect of the sandwich core. The sandwich panels were fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that slightly slender (along unidirectional compressive loading axis) rectangular sandwich panels have the most desirable stiffness-to-weight ratios for aerospace structural applications; the degradation of buckling strength of sandwich panels with rising temperature is faster in shear than in compression; and the fiber orientation of the face sheets for optimum combined-load buckling strength of sandwich panels is a strong function of both loading condition and panel aspect ratio. Under the same specific weight and panel aspect ratio, a sandwich panel with metal matrix composite face sheets has much higher buckling strength than one having monolithic face sheets.

  19. Outbreak of Salmonella indiana associated with egg mayonnaise sandwiches at an acute NHS hospital.

    Science.gov (United States)

    Mason, B W; Williams, N; Salmon, R L; Lewis, A; Price, J; Johnston, K M; Trott, R M

    2001-12-01

    An outbreak of Salmonella indiana infection in December 2000 affected 17 staff, relatives and patients at an acute NHS Hospital in Swansea. Epidemiological investigation identified egg mayonnaise sandwiches as the vehicle of infection. It was not possible to definitively determine the source of the infection or how the prepared sandwiches became contaminated. The most likely explanation was a pasteurisation failure of a batch of the egg roll used to make these sandwiches. Sandwiches are the most frequently identified vehicle of infection in foodborne outbreaks of salmonella infection in hospitals in England and Wales. The process of sandwich preparation has inherent risks because it involves considerable handling of food, which is consumed without further cooking. Care is required in all stages of preparation including the sourcing of materials used to produce the sandwiches. NHS Trusts should review their Hazard Analysis Critical Control Point plans for sandwich production.

  20. A large outbreak of salmonellosis associated with sandwiches contaminated with multiple bacterial pathogens purchased via an online shopping service.

    Science.gov (United States)

    Wei, Sung-Hsi; Huang, Angela S; Liao, Ying-Shu; Liu, Yu-Lun; Chiou, Chien-Shun

    2014-03-01

    Food sold over the internet is an emerging business that also presents a concern with regard to food safety. A nationwide foodborne disease outbreak associated with sandwiches purchased from an online shop in July 2010 is reported. Consumers were telephone interviewed with a structured questionnaire and specimens were collected for etiological examination. A total of 886 consumers were successfully contacted and completed the questionnaires; 36.6% had become ill, with a median incubation period of 18 h (range, 6-66 h). The major symptoms included diarrhea (89.2%), abdominal pain (69.8%), fever (47.5%), headache (32.7%), and vomiting (17.3%). Microbiological laboratories isolated Salmonella enterica serovar Enteritidis, Salmonella Virchow, Staphylococcus aureus, Bacillus cereus, and enterotoxigenic Escherichia coli from the contaminated sandwiches, Salmonella Enteritidis and Salmonella Virchow from the patients, and Salmonella Enteritidis and Staphylococcus aureus from food handlers. Pulsed-field gel electrophoresis genotyping suggested a common origin of Salmonella bacteria recovered from the patients, food, and a food handler. Among the pathogens detected, the symptoms and incubation period indicated that Salmonella, likely of egg origin, was the probable causative agent of the outbreak. This outbreak illustrates the importance of meticulous hygiene practices during food preparation and temperature control during food shipment and the food safety challenges posed by online food-shopping services.

  1. Impact load mitigation in sandwich beams using local resonators

    CERN Document Server

    Sharma, B

    2015-01-01

    Dynamic response of sandwich beams with resonators embedded in the cores subjected to impact loads is studied. Using finite element models the effectiveness of various local resonator frequencies under a given impact load is compared to the behavior of an equivalent mass beam. It is shown that addition of appropriately chosen local resonators into the sandwich beam is an effective method of improving its flexural bending behavior under impact loads. The effect of a given local resonance frequency under different impact load durations is also studied. It is demonstrated that the choice of appropriate local resonance frequency depends on the impact duration. Further, by performing transverse impact experiments, the finite element models are verified and the advantage of using internal resonators under impact loading conditions is demonstrated.

  2. Preserving entanglement under decoherence and sandwiching all separable states

    CERN Document Server

    Lockhart, R B; Lockhart, Robert; Steiner, Michael

    2000-01-01

    Every entangled state can be perturbed, for instance by decoherence, and stay entangled. For a large class of pure entangled states, we show how large the perturbation can be. Our class includes all pure bipartite and all maximally entangled states. For an entangled state, E, the constucted neighborhood of entangled states is the region outside two parallel hyperplanes, which sandwich the set of all separable states. The states for which these neighborhoods are largest are the maximally entangled ones. As the number of particles, or the dimensions of the Hilbert spaces for two of the particles increases, the distance between two of the hyperplanes which sandwich the separable states goes to zero. It is easy to decide if a state Q is in the neighborhood of entangled states we construct for an entangled state E. One merely has to check if the trace of EQ is greater than a constant which depends upon E and which we determine.

  3. Natural fabric sandwich laminate composites: development and investigation

    Indian Academy of Sciences (India)

    C K ARVINDA PANDIAN; H SIDDHI JAILANI; A RAJADURAI

    2017-02-01

    In this work, eco-friendly natural fabric sandwich laminate (NFSL) composites are formulated using jute and linen-fabric-reinforced epoxy with different layer ratios (5:0, 4:1, 3:2, 2:3, 1:4 and 0:5) by hand layup system. Different mechanical attributes (tensile, flexural and impact) of the NFSL composites are quantified. Thermal stability and water absorption behaviour of the NFSL composites are also assessed. A scanning electron microscope (SEM) and optical microscope are used for qualitative analysis of NFSL composites’ interfacial properties. Two layers of jute and three layers of linen sandwich laminate have registered peak values in tensile and impact properties. The five layers of linen laminate composite have exhibited high flexural strength, been proven to have good thermal stability and furthermore shown better water absorption behaviour than any other laminate composites.

  4. Non-Uniform Compressive Strength of Debonded Sandwich Panels

    DEFF Research Database (Denmark)

    Berggreen, Carl Christian; Simonsen, Bo Cerup

    2005-01-01

    This article describes the development, validation and application of a FEM based numerical model for prediction of residual strength of damaged sandwich panels. The core of the theoretical method is a newly developed procedure for prediction of the propagation of a face-core debond. As demonstra......This article describes the development, validation and application of a FEM based numerical model for prediction of residual strength of damaged sandwich panels. The core of the theoretical method is a newly developed procedure for prediction of the propagation of a face-core debond.......(2005)., shows that the model is indeed able to predict the failure modes and the residual strength of damaged panels with accuracy sufficient for practical applications. This opens up for a number of important engineering applications, for example risk-based inspection and repair schemes....

  5. Applications of thin-film sandwich crystallization platforms

    Energy Technology Data Exchange (ETDEWEB)

    Axford, Danny, E-mail: danny.axford@diamond.ac.uk; Aller, Pierre; Sanchez-Weatherby, Juan; Sandy, James [Diamond Light Source, Harwell Oxford, Didcot OX11 0DE (United Kingdom)

    2016-03-24

    Crystallization via sandwiches of thin polymer films is presented and discussed. Examples are shown of protein crystallization in, and data collection from, solutions sandwiched between thin polymer films using vapour-diffusion and batch methods. The crystallization platform is optimal for both visualization and in situ data collection, with the need for traditional harvesting being eliminated. In wells constructed from the thinnest plastic and with a minimum of aqueous liquid, flash-cooling to 100 K is possible without significant ice formation and without any degradation in crystal quality. The approach is simple; it utilizes low-cost consumables but yields high-quality data with minimal sample intervention and, with the very low levels of background X-ray scatter that are observed, is optimal for microcrystals.

  6. Sandwich-like Reconstruction of Anterior Skull Base Defects

    Institute of Scientific and Technical Information of China (English)

    Wang Zheng-min; Wang De-hui

    2001-01-01

    Objective: To evaluate the safety and efficacy of new modality of anterior skull base repair,namely sandwich-like reconstruction of anterior skull base defects. Methods: A retrospective analysis of patients who underwent transcranial or transcranial-facial resections of malignant or benign aggressive tumors involving the anterior skull base was conducted in our department. We used the sandwich-like reconstruction, using pedicled pericranial flap, frontal muscle flap and free abdominal adipose tissue between them, to separate of cranial cavity and aerodigest tract and keep the frontal lobes in place following resections of anterior skull base tumors. Results: From October, 1984 to October, 1998, 116 patients underwent transcranial or transcranialfacial approach for the resection of malignant or aggressive benign tumor, and sandwich-like repairs were performed for the anterior skull base defect. 54 (46.6 % ) patients had previous operation, with a maximum of 5 surgeries. The average age of patients was 35.9 years old, ranging form 6 to 73 years old. Forty-eight (41.4%)patients had malignant neoplasmas, and sixty-eight (58.6%) patients had benign aggressive tumors. In our series, with the maximal follow-ups for as long as 14 years, NO one had early failure of the one-stage reconstruction. CSF fluid leakage was not encountered, nor was ascending bacterial meningitis observed. No immediate or delayed prolapse of dura or frontal lobes was observed. Conclusion: We conclude that the sandwich-like reconstruction, using pericranial flap, frontal muscle flap and free abdominal adipose between them, is an extremely safe and effective procedure for the repair of skull base defect, even when tumor extensively involves anterior skull base.

  7. Sandwich-like Reconstruction of Anterior Skull Base Defects

    Institute of Scientific and Technical Information of China (English)

    WangZheng-min,MD; WangDe-hui,MD

    2001-01-01

    Objective:To evaluate the safety and efficacy of new modality of anterior skull base repair,namely sandwich-like reconstruction of anterior skull base defects. Methods : A retrospective analysis of patients who underwent wanscranial or wanscranial-facial resections of malignant or benign aggressive tumors involving the anterior skull base was conducted in our department. We used the sandwich-like reconstruction, using pedicled pericranial flap, frontal muscle flap and free abdominal adipose tissue between them, to separate of cranial cavity and aerodigest tract and keep the frontal lobes in place following resections of anterior skull base tumors. Results: From October, 1984 to October, 1998, 116 patients underwent tmnscranial or tmnscranial-facial approach for the resection of malignant or aggressive benign tumor, and sandwich-like repairs were performed for the anterior skull base defect.54 (46.6%) patients had previous operation, with a maximum of 5 surgeries. The average age of patients was 35.9 years old, ranging form 6 to 73 years old. Forty-eight (41.4%) patients had malignant neoplasmas, and sixty-eight (58.6%) patients had benign aggressive tumors. In our series, with the maximal follow-ups for as long as 14 years, NO one had early failure of the one-stage reconstruction. CSF fluid leakage was not encountered, nor was ascending bacterial meningitis observed. No immediate or delayed prolapse of dura or frontal lobes was observed. Conclusion: We conclude that the sandwich-like reconstruction, using pericranial flap, frontal muscle flap and free abdominal adipose between them, is an extremely safe and effective procedure for the repair of skull base defect, even when tumor extensively involves anterior skull base.

  8. Residual Strength of In-plane Loaded Debonded Sandwich Panels

    DEFF Research Database (Denmark)

    Lundsgaard-Larsen, Christian; Nøkkentved, Alexandros; Berggreen, Carl Christian

    2005-01-01

    Face/core debond damaged sandwich panels exposed to uniform and non-uniform compression loads are studied experimentally. The panel geometry is full-scale rectangular with a centrally located circular prefabricated debond. The results show a considerable strength reduction with increasing debond...... diameter, with the failure mechanisms varying between buckling driven debond propagation and face compression failure for large and small debonds respectively....

  9. Sandwiched R\\'enyi Convergence for Quantum Evolutions

    OpenAIRE

    Müller-Hermes, Alexander; Franca, Daniel Stilck

    2016-01-01

    We study the speed of convergence of a primitive quantum time evolution towards its fixed point in the distance of sandwiched R\\'enyi divergences. For each of these distance measures the convergence is typically exponentially fast and the best exponent is given by a constant (similar to a logarithmic Sobolev constant) depending only on the generator of the time evolution. We establish relations between these constants and the logarithmic Sobolev constants as well as the spectral gap. An impor...

  10. The Generalized Thin-Sandwich Problem and its Local Solvability

    CERN Document Server

    Giulini, D

    1999-01-01

    We consider Einstein Gravity coupled to dynamical matter consisting of a gauge field with any compact gauge group and minimally coupled scalar fields. We investigate the conditions under which a free specification of a spatial field configuration for the total system and its derivative with respect to coordinate-time determines a solution to the field equations (generalized thin-sandwich problem). Sufficient conditions for local solvability (in the space of fields) are established.

  11. An asymptotically exact theory of smart sandwich shells

    CERN Document Server

    Le, Khanh Chau

    2016-01-01

    An asymptotically exact two-dimensional theory of elastic-piezoceramic sandwich shells is derived by the variational-asymptotic method. The error estimation of the constructed theory is given in the energetic norm. As an application, analytical solution to the problem of forced vibration of a circular elastic plate partially covered by two piezoceramic patches with thickness polarization excited by a harmonic voltage is found.

  12. Flexural Behavior of Two-Way Sandwiched Slabs

    OpenAIRE

    Pachpande, Jivan Vilas

    2015-01-01

    This dissertation presents the details of the findings of a study focused on evaluating the structural behavior of three-dimensional (3D) cementitious sandwich panels with Expanded Polystyrene (EPS) foam core for two-way slab applications. In this study, both theoretical and finite element numerical analysis procedures were adopted to predict the performance of such slabs under out-of-plane loading conditions. The results from theoretical and finite element analysis were verified by compariso...

  13. Graphene Sandwiched Mesostructured Li-Ion Battery Electrodes.

    Science.gov (United States)

    Liu, Jinyun; Zheng, Qiye; Goodman, Matthew D; Zhu, Haoyue; Kim, Jinwoo; Krueger, Neil A; Ning, Hailong; Huang, Xingjiu; Liu, Jinhuai; Terrones, Mauricio; Braun, Paul V

    2016-09-01

    A deterministic graphene-sandwiched Li-ion battery electrode consisting of an integrated 3D mesostructure of electrochemically active materials and graphene is presented. As demonstrations, electrodes with active nanomaterials that coat (V2 O5 @graphene@V2 O5 cathode) or are coated by (graphene@Si@graphene anode) graphene are fabricated. These electrodes exhibit high capacities and ultralong cycle lives (the cathode can be cycled over 2000 times with minimal capacity fade).

  14. Double Rosensweig instability in a ferrofluid sandwich structure

    OpenAIRE

    Rannacher, Dirk; Engel, Andreas

    2003-01-01

    We consider a horizontal ferrofluid layer sandwiched between two layers of immiscible non-magnetic fluids. In a sufficiently strong vertical magnetic field the flat interfaces between magnetic and non-magnetic fluids become unstable to the formation of peaks. We theoretically investigate the interplay between these two instabilities for different combinations of the parameters of the fluids and analyze the evolving interfacial patterns. We also estimate the critical magnetic field strength at...

  15. Two-dimensional analysis of shallow sandwich panels

    DEFF Research Database (Denmark)

    Skvortsov, V; Bozhevolnaya, Elena

    2001-01-01

    The shallow singly curved and rectangular in-plane sandwich panels affected by lateral loads are considered. The set of governing equations on the basis of the Timoshenko-Reissner plate theory is derived for these panels in the case of general boundary conditions. Usage of any real boundary condi...... all four edges and for the panel that is simply supported along its curved boundaries and has hinge-like supports along the straight boundaries. (C) 2001 Elsevier Science Ltd. All rights reserved....

  16. A sandwich ELISA to detect VHSV and IPNV in turbot

    OpenAIRE

    Vázquez-Brañas, M. (Manuel); Coll-Morales, J. (Julio); Estepa, A

    1994-01-01

    Abstract: The recent demonstration that reared turbot (Scophthalmus maximus L) is a natural host for salmonid rhabdoviruses has made their rapid detection relevant to these fish species. A unique protocol to select and use non-competitive monoclonal antibodies (Mabs) for two high-sensitivity sandwich ELISAs has been developed to detect both infectious pancreatic necrosis virus (IPNV) and viral haemorrhagic septicaemia virus (VHSV) in turbot kidney extracts to assess the possibility of using t...

  17. Residual Strength of In-plane Loaded Debonded Sandwich Panels

    DEFF Research Database (Denmark)

    Berggreen, Carl Christian; Simonsen, Bo Cerup

    2005-01-01

    This paper presents a FEM based numerical model for prediction of residual strength of damaged sandwich panels. As demonstrated, the model can predict the maximum load carrying capacity of real-life panels with debond damages, where the failure is governed by face-sheet buckling followed by debond...... growth. Comparison of the theoretical predictions is carried out against a series of largescale experiments described in Lundsgaard-Larsen et al. (2005)...

  18. 16 CFR Figure 3 to Part 1610 - Specimen Holder Supported in Specimen Rack

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Specimen Holder Supported in Specimen Rack 3 Figure 3 to Part 1610 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FLAMMABLE FABRICS ACT... Holder Supported in Specimen Rack ER25MR08.002...

  19. Sandwich Structured Composites for Aeronautics: Methods of Manufacturing Affecting Some Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Aneta Krzyżak

    2016-01-01

    Full Text Available Sandwich panels are composites which consist of two thin laminate outer skins and lightweight (e.g., honeycomb thick core structure. Owing to the core structure, such composites are distinguished by stiffness. Despite the thickness of the core, sandwich composites are light and have a relatively high flexural strength. These composites have a spatial structure, which affects good thermal insulator properties. Sandwich panels are used in aeronautics, road vehicles, ships, and civil engineering. The mechanical properties of these composites are directly dependent on the properties of sandwich components and method of manufacturing. The paper presents some aspects of technology and its influence on mechanical properties of sandwich structure polymer composites. The sandwiches described in the paper were made by three different methods: hand lay-up, press method, and autoclave use. The samples of sandwiches were tested for failure caused by impact load. Sandwiches prepared in the same way were used for structural analysis of adhesive layer between panels and core. The results of research showed that the method of manufacturing, more precisely the pressure while forming sandwich panels, influences some mechanical properties of sandwich structured polymer composites such as flexural strength, impact strength, and compressive strength.

  20. Reconstituted Charpy impact specimens. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Perrin, J.S.; Wullaert, R.A.; McConnell, P.; Server, W.L.; Fromm, E.O.

    1982-12-01

    The arc stud welding process was used to produce new, full size Charpy V-notch impact specimens from halves of Charpy specimens which had been previously tested. The apparatus was developed such that it could be used not only for unirradiated specimens, but also so that it could be adapted for in-cell use to produce new reconstituted specimens of irradiated material. The materials studied are of interest in nuclear applications. They include A533B, A36, A516-80, submerged arc weld metal (A508 base metal), HY80, cast duplex stainless steel, irradiated A533B, and irradiated submerged arc weld metal (A508 base metal). Both unirradiated and irradiated specimens were successfully produced and subsequently impact tested. In general, there was excellent agreement when comparing the original curves to the subsequent curves generated with reconstituted specimens. This program has shown that the arc stud welding process is well suited for producing reconstituted specimens at a reasonable cost using either unirradiated or irradiated material.

  1. Impact properties of aluminium - glass fiber reinforced plastics sandwich panels

    Directory of Open Access Journals (Sweden)

    Mathivanan Periasamy

    2012-06-01

    Full Text Available Aluminium - glass fiber reinforced plastics (GFRP sandwich panels are hybrid laminates consisting of GFRP bonded with thin aluminum sheets on either side. Such sandwich materials are increasingly used in airplane and automobile structures. Laminates with varying aluminium thickness fractions, fiber volume fractions and orientation in the layers of GFRP were fabricated by hand lay up method and evaluated for their impact performance by conducting drop weight tests under low velocity impacts. The impact energy required for initiating a crack in the outer aluminium layer as well as the energy required for perforation was recorded. The impact load-time history was also recorded to understand the failure behavior. The damage depth and the damage area were measured to evaluate the impact resistance. Optical photography and scanning electron micrographs were taken to visualize the crack and the damage zone. The bidirectional cross-ply hybrid laminate (CPHL has been found to exhibit better impact performance and damage resistance than the unidirectional hybrid laminate (UDHL. Increase in aluminium thickness fraction (Al tf and fiber volume fraction (Vf resulted in an increase in the impact energy required for cracking and perforation. On an overall basis, the sandwich panels exhibited better impact performance than the monolithic aluminium.

  2. Sandwich-structured hollow fiber membranes for osmotic power generation

    KAUST Repository

    Fu, Feng Jiang

    2015-11-01

    In this work, a novel sandwich-structured hollow fiber membrane has been developed via a specially designed spinneret and optimized spinning conditions. With this specially designed spinneret, the outer layer, which is the most crucial part of the sandwich-structured membrane, is maintained the same as the traditional dual-layer membrane. The inner substrate layer is separated into two layers: (1) an ultra-thin middle layer comprising a high molecular weight polyvinylpyrrolidone (PVP) additive to enhance integration with the outer polybenzimidazole (PBI) selective layer, and (2) an inner-layer to provide strong mechanical strength for the membrane. Experimental results show that a high water permeability and good mechanical strength could be achieved without the expensive post treatment process to remove PVP which was necessary for the dual-layer pressure retarded osmosis (PRO) membranes. By optimizing the composition, the membrane shows a maximum power density of 6.23W/m2 at a hydraulic pressure of 22.0bar when 1M NaCl and 10mM NaCl are used as the draw and feed solutions, respectively. To our best knowledge, this is the best phase inversion hollow fiber membrane with an outer selective PBI layer for osmotic power generation. In addition, this is the first work that shows how to fabricate sandwich-structured hollow fiber membranes for various applications. © 2015 Elsevier B.V.

  3. Sandwiched Rényi divergence satisfies data processing inequality

    Energy Technology Data Exchange (ETDEWEB)

    Beigi, Salman [School of Mathematics, Institute for Research in Fundamental Sciences (IPM), P.O. Box 19395-5746, Tehran (Iran, Islamic Republic of)

    2013-12-15

    Sandwiched (quantum) α-Rényi divergence has been recently defined in the independent works of Wilde et al. [“Strong converse for the classical capacity of entanglement-breaking channels,” preprint http://arxiv.org/abs/arXiv:1306.1586 (2013)] and Müller-Lennert et al. [“On quantum Rényi entropies: a new definition, some properties and several conjectures,” preprint http://arxiv.org/abs/arXiv:1306.3142v1 (2013)]. This new quantum divergence has already found applications in quantum information theory. Here we further investigate properties of this new quantum divergence. In particular, we show that sandwiched α-Rényi divergence satisfies the data processing inequality for all values of α > 1. Moreover we prove that α-Holevo information, a variant of Holevo information defined in terms of sandwiched α-Rényi divergence, is super-additive. Our results are based on Hölder's inequality, the Riesz-Thorin theorem and ideas from the theory of complex interpolation. We also employ Sion's minimax theorem.

  4. Static and Fatigue Characterization of Nomex Honeycomb Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Keskes Boualem

    2013-07-01

    Full Text Available The main benefits of using the sandwich concept in structural components are the high stiffness, good fatigue resistance and low weight ratios. Recent advances in materials and construction techniques have resulted in further improvement and increased uniformity of the sandwich composite properties. In order to use these materials in different applications, the knowledge of simply their static properties alone is not sufficient but additional information on their fatigue properties and durability are required. In this paper, first static and fatigue tests on four points bending of nomex honeycomb composite sandwich panels have been performed. Load/displacement and S-N fatigue curves are presented and analysed. Fatigue failure and damage modes are observed with an optical microscope and are discussed. The second is to address such fatigue behaviour by using a damage model and check it by experimentation. This fatigue damage model is based on stiffness degradation, which is used as a damage indicator. Two non-linear cumulative damage models derived from the chosen stiffness degradation equation are examined with assumption of linear Miner's damage summation. Predicted results are compared with available experimental data.

  5. Structural modeling of sandwich structures with lightweight cellular cores

    Science.gov (United States)

    Liu, T.; Deng, Z. C.; Lu, T. J.

    2007-10-01

    An effective single layered finite element (FE) computational model is proposed to predict the structural behavior of lightweight sandwich panels having two dimensional (2D) prismatic or three dimensional (3D) truss cores. Three different types of cellular core topology are considered: pyramidal truss core (3D), Kagome truss core (3D) and corrugated core (2D), representing three kinds of material anisotropy: orthotropic, monoclinic and general anisotropic. A homogenization technique is developed to obtain the homogenized macroscopic stiffness properties of the cellular core. In comparison with the results obtained by using detailed FE model, the single layered computational model can give acceptable predictions for both the static and dynamic behaviors of orthotropic truss core sandwich panels. However, for non-orthotropic 3D truss cores, the predictions are not so well. For both static and dynamic behaviors of a 2D corrugated core sandwich panel, the predictions derived by the single layered computational model is generally acceptable when the size of the unit cell varies within a certain range, with the predictions for moderately strong or strong corrugated cores more accurate than those for weak cores.

  6. Microtomography with a sandwich detector for mouse bone imaging

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seung Ho; Kim, Junwoo; Kim, Ho Kyung [Pusan National University, Busan (Korea, Republic of); Youn, Hanbean; Jeon, Hosang [Pusan National University Yangsan Hospital, Yangsan (Korea, Republic of)

    2015-10-15

    Single-shot dual-energy imaging, using sandwich detector, the rear detector usually uses a thicker x-ray converter to enhance quantum efficiency with the higher-energy spectrum, hence providing a blurrier image than the front detector. The weighted logarithmic subtraction of the two images therefore results in a form of unsharp masking that enhances edges in the resultant image. Inspired by this observation, we have developed a micro computed tomography (micro-CT) system with the sandwich detector for high-resolution bone imaging of small animals. The sandwich detector consists of two flat-panel detectors by stacking one upon the other. Although the x-ray beam continuously irradiates, the step-rotation of an object and stay-readout of projection data were considered for the scanning and data gathering. It will be necessary that more elaborate experiments with the mouse and/or other quantitative phantoms. And quantification of the image quality of bone-enhanced images in comparisons with the conventional images will be performed. The image analysis of differences between bone-enhanced images obtained from the projection- and image-based approaches can be performed.

  7. Static and Fatigue Characterization of Nomex Honeycomb Sandwich Panels

    Directory of Open Access Journals (Sweden)

    Keskes Boualem

    2013-07-01

    Full Text Available The main benefits of using the sandwich concept in structural components are the high stiffness, good fatigue resistance and low weight ratios. Recent advances in materials and construction techniques have resulted in further improvement and increased uniformity of the sandwich composite properties. In order to use these materials in different applications, the knowledge of simply their static properties alone is not sufficient but additional information on their fatigue properties and durability are required. In this paper, first static and fatigue tests on four points bending of nomex honeycomb composite sandwich panels have been performed. Load/displacement and S-N fatigue curves are presented and analysed. Fatigue failure and damage modes are observed with an optical microscope and are discussed. The second is to address such fatigue behaviour by using a damage model and check it by experimentation. This fatigue damage model is based on stiffness degradation, which is used as a damage indicator. Two non-linear cumulative damage models derived from the chosen stiffness degradation equation are examined with assumption of linear Miner's damage summation. Predicted results are compared with available experimental data.

  8. Systematic selection of modified aptamer pairs for diagnostic sandwich assays.

    Science.gov (United States)

    Ochsner, Urs A; Green, Louis S; Gold, Larry; Janjic, Nebojsa

    2014-01-01

    Protein diagnostic applications typically require pairs of analyte-specific reagents for capture and detection. We developed methods for the systematic isolation of slow off-rate modified aptamer (SOMAmer) reagents that bind to different epitopes and allow efficient pair-wise screening of multiple ligands. SOMAmers were generated via a second systematic evolution of ligands by exponential enrichment (SELEX), using complexes of target proteins with a primary, non-amplifiable SOMAmer and employing different modified nucleotides (e.g., naphthylmethyl- or tryptaminocarbonyl-dU) to favor alternate binding epitopes. Non-competing binding of primary and secondary SOMAmers was tested in radiolabel competition and sandwich binding assays. Multiplexed high-throughput screening for sandwich pairs utilized the Luminex platform, with primary SOMAmers as capture agents attached to different types of LumAvidin beads, which were then pooled for testing the secondary SOMAmers individually as detection agents. Functional SOMAmer pairs were obtained for Clostridium difficile binary toxin (CdtA) and for a panel of human proteins (ANGPT2, TSP2, CRDL1, MATN2, GPVI, C7, PLG) that had been previously identified as promising markers for cardiovascular risk. The equilibrium dissociation constants (Kd values) ranged from 0.02-2.7 nM, and the detection limits were in the low picomolar range for these proteins in SOMAmer sandwich assays. These results indicate that SOMAmer pairs hold promise for the development of rapid tests or specific diagnostic panels.

  9. Structural modeling of sandwich structures with lightweight cellular cores

    Institute of Scientific and Technical Information of China (English)

    T. Liu; Z. C. Deng; T. J. Lu

    2007-01-01

    An effective single layered finite element (FE) computational model is proposed to predict the structural behavior of lightweight sandwich panels having two dimensional (2D) prismatic or three dimensional (3D) truss cores.Three different types of cellular core topology are considered: pyramidal truss core (3D), Kagome truss core (3D) and corrugated core (2D), representing three kinds of material anisotropy: orthotropic, monoclinic and general anisotropic. A homogenization technique is developed to obtain the homogenized macroscopic stiffness properties of the cellular core. In comparison with the results obtained by using detailed FE model, the single layered computational model cangive acceptable predictions for both the static and dynamic behaviors of orthotropic truss core sandwich panels. However, for non-orthotropic 3D truss cores, the predictions are not so well. For both static and dynamic behaviors of a 2D corrugated core sandwich panel, the predictions derived by the single layered computational model is generally acceptable when the size of the unit cell varies within a certain range, with the predictions for moderately strong or strong corrugated cores more accurate than those for weak cores.

  10. Stress Corrosion Crack Growth Behavior of Titanium Alloy/Bioactive Glasses Sandwiches in Simulated Human Physiological Environment

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Based on a series of newly developed bioactive glasses having suitable thermo-mechanical properties to allow application as fixation agents between bone and titanium alloy biomedical implants, the stress corrosion crack growth(SCCG) behavior of their interfaces with Ti6Al4V was investigated in simulated body fluid (SBF) with the objectiveof discerning the salient mechanisms of crack advance and to assess the reliability of the bonds. Results indicatedthat crack growth rates in Ti6Al4V/glass/Ti6Al4V sandwich specimens were nearly the same as or slightly lowerthan those in the bulk glasses at comparable stress intensities; indeed, cracks would prefer to propagate off theinterface, suggesting that the Ti6Al4V/glass interface has relatively good crack-growth resistance. Mechanistically,interfacial crack growth appears to be controlled by the classic stress corrosion mechanisms for silicate glasses, withno discernible effect of bioactivity on the SCCG behavior being observed.

  11. Mode-II-Fracture Specimen And Holder

    Science.gov (United States)

    Buzzard, Robert J.; Ghosn, Louis; Succop, George

    1991-01-01

    Test specimen and loading frame developed for fatigue and fracture testing of materials under mode-II (sliding-mode) loading. Assembly placed in compression-testing machine. Loads directed oppositely along centerline cause self-similar crack to propagate. Enables consistently accurate alignment of specimens before insertion of specimen/frame assemblies into compression-testing machine. Makes design attractive for testing in hostile environments in which access to machine or furnace limited. Additional feature, with little or no modification, placed horizontally into impact testing machine and subjected to loading at high speeds.

  12. An h-p Finite Element Vibration Analysis of Open Conical Sandwich Panels and Conical Sandwich Frusta

    Science.gov (United States)

    BARDELL, N. S.; LANGLEY, R. S.; DUNSDON, J. M.; AGLIETTI, G. S.

    1999-09-01

    The vibration study of a general three-layer conical sandwich panel based on theh -p version of the finite element method is presented in this paper. No restriction is placed on the degree of curvature of the shell, thereby relaxing the strictures associated with shallow shell theory. The methodology incorporates a new set of trigonometric functions to provide the element p -enrichment, and elements may be joined together to model either open conical panels, or complete conical frusta (circumferentially connected, but open at each end). The full range of classical boundary conditions, which includes free, clamped, simply supported and shear diaphragm edges, may be applied in any combination to open and closed panels, thereby facilitating the study of a wide range of conical sandwich shells. The convergence properties of this element have been established for different combinations of the h - and p -parameters, thereby assuring its integrity for more general use. Since very little work has been reported on the vibration characteristic of either circumferentially closed or open conical sandwich panels, the main thrust of this work has been to present and validate an efficient modelling technique, rather than to perform numerous parameter and/or sensitivity studies. To this end, some new results are presented and subsequently validated using a commercially available finite element package. It is shown that for results of comparable accuracy, models constructed using the h-p formulation require significantly fewer degrees of freedom than those assembled using the commercial package. Some preliminary experimental results are also included for completeness.

  13. Structure of Wet Specimens in Electron Microscopy

    Science.gov (United States)

    Parsons, D. F.

    1974-01-01

    Discussed are past work and recent advances in the use of electron microscopes for viewing structures immersed in gas and liquid. Improved environmental chambers make it possible to examine wet specimens easily. (Author/RH)

  14. Testing Biopsy and Cytology Specimens for Cancer

    Science.gov (United States)

    ... Your Diagnosis Exams and Tests for Cancer Testing Biopsy and Cytology Specimens for Cancer Waiting to hear ... who tell you whether the cells in your biopsy sample are cancer or not. How is cancer ...

  15. Structure of Wet Specimens in Electron Microscopy

    Science.gov (United States)

    Parsons, D. F.

    1974-01-01

    Discussed are past work and recent advances in the use of electron microscopes for viewing structures immersed in gas and liquid. Improved environmental chambers make it possible to examine wet specimens easily. (Author/RH)

  16. Tensile and Compressive Properties of Woven Kenaf/Glass Sandwich Hybrid Composites

    Directory of Open Access Journals (Sweden)

    Mohaiman J. Sharba

    2016-01-01

    Full Text Available Monotonic (tensile and compression properties of woven kenaf/glass reinforced unsaturated polyester sandwich hybrid composites have been experimentally investigated. Five types of composites laminates were fabricated using a combination of hand lay-up and cold press techniques, postcured for two hours at 80°C and left for 48 hours at room temperature. The hybrid composites contained fixed six layers of glass as a shell, three on each side, whereas the number of core kenaf layers was changed in three stages to get S1, S2, and S3 hybrid composites. Composites specimens with pure glass and kenaf were also fabricated for comparison. It was found that one kenaf layer replaced about 20% of total fiber weight fraction of the composite; this leads to reducing the density of final hybrid composite by 13%. Besides, in mechanical properties perspective, there are less than 1% reduction in compression strength and 40% in tensile strength when compared to pure glass composite. Generally, the results revealed that the best performance was observed in S1, which showed a good balance of all mechanical properties determined in this work.

  17. Localization of Transversal Cracks in Sandwich Beams and Evaluation of Their Severity

    Directory of Open Access Journals (Sweden)

    G. R. Gillich

    2014-01-01

    Full Text Available An algorithm to assess transversal cracks in composite structures based on natural frequency changes due to damage is proposed. The damage assessment is performed in two steps; first the crack location is found, and afterwards an evaluation of its severity is performed. The technique is based on a mathematical relation that provides the exact solution for the frequency changes of bending vibration modes, considering two terms. The first term is related to the strain energy stored in the beam, while the second term considers the increase of flexibility due to damage. Thus, it is possible to separate the problems of localization and severity assessment, which makes the localization process independent of the beams cross-section shape and boundary conditions. In fact, the process consists of comparing vectors representing the measured frequency shifts with patterns constructed using the mode shape curvatures of the undamaged beam. Once the damage is localized, the evaluation of its severity is made taking into account the global rigidity reduction. The damage identification algorithm was validated by experiments performed on numerous sandwich panel specimens.

  18. Structure and magnetic anisotropy evolution in Au/Co/Au sandwiches upon thermal treatment

    Energy Technology Data Exchange (ETDEWEB)

    Wawro, A.; Kurant, Z.; Baczewski, L.T.; Pankowski, P.; Pelka, J.B.; Maneikis, A. [Institute of Physics, Polish Academy of Sciences, Al. Lotnikow 32/46, 02-668 Warsaw (Poland); Bojko, A.; Zablotskii, V.; Maziewski, A. [Institute of Experimental Physics, University of Bialystok, ul. Lipowa 41, 15-424 Bialystok (Poland)

    2006-01-01

    The correlation between structural and magnetic properties of Au(111)/Co(0001)/Au(111) sandwiches with perpendicular magnetic anisotropy, grown by molecular beam epitaxy, has been studied in details. Thermal treatment in the range between room temperature and 300 C at various stages of samples growth process as well as after its completion is applied as a factor modifying the structure of studied specimens. Annealing at 150 C does not affect substantially either crystalline structure or perpendicular magnetic anisotropy. At 250 C the RHEED pattern of Co layers reveals the loss of the lattice coherence with Au underlayer and the analysis of synchrotron radiation reflectometry leads to the conclusion that the continuity of Co layers is lost. Structural evolution upon thermal treatment is well correlated with changes of magnetic anisotropy studied by magnetooptical Kerr effect. After annealing at 250 C magnetization switches from out-of-plane to in-plane orientation, which is explained in terms of interfacial and magnetoelastic contributions to the sample magnetic anisotropy. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  19. A Numerical Study on the Edgewise Compression Strength of Sandwich Structures with Facesheet-Core Disbonds

    Science.gov (United States)

    Bergan, Andrew C.

    2017-01-01

    Damage tolerant design approaches require determination of critical damage modes and flaw sizes in order to establish nondestructive evaluation detection requirements. A finite element model is developed to assess the effect of circular facesheet-core disbonds on the strength of sandwich specimens subjected to edgewise compressive loads for the purpose of predicting the critical flaw size for a variety of design parameters. Postbuckling analyses are conducted in which an initial imperfection is seeded using results from a linear buckling analysis. Both the virtual crack closure technique (VCCT) and cohesive elements are considered for modeling disbond growth. Predictions from analyses using the VCCT and analyses using cohesive elements are in good correlation. A series of parametric analyses are conducted to investigate the effect of core thickness and material, facesheet layup, facesheet-core interface properties, and curvature on the criticality of facesheet-core disbonds of various sizes. The results from these analyses provide a basis for determining the critical flaw size for facesheet-core disbonds subjected to edgewise compression loads and, therefore, nondestructive evaluation flaw detection requirements for this configuration.

  20. Impact of specimen adequacy on the assessment of renal allograft biopsy specimens.

    Science.gov (United States)

    Cimen, S; Geldenhuys, L; Guler, S; Imamoglu, A; Molinari, M

    2016-01-01

    The Banff classification was introduced to achieve uniformity in the assessment of renal allograft biopsies. The primary aim of this study was to evaluate the impact of specimen adequacy on the Banff classification. All renal allograft biopsies obtained between July 2010 and June 2012 for suspicion of acute rejection were included. Pre-biopsy clinical data on suspected diagnosis and time from renal transplantation were provided to a nephropathologist who was blinded to the original pathological report. Second pathological readings were compared with the original to assess agreement stratified by specimen adequacy. Cohen's kappa test and Fisher's exact test were used for statistical analyses. Forty-nine specimens were reviewed. Among these specimens, 81.6% were classified as adequate, 6.12% as minimal, and 12.24% as unsatisfactory. The agreement analysis among the first and second readings revealed a kappa value of 0.97. Full agreement between readings was found in 75% of the adequate specimens, 66.7 and 50% for minimal and unsatisfactory specimens, respectively. There was no agreement between readings in 5% of the adequate specimens and 16.7% of the unsatisfactory specimens. For the entire sample full agreement was found in 71.4%, partial agreement in 20.4% and no agreement in 8.2% of the specimens. Statistical analysis using Fisher's exact test yielded a P value above 0.25 showing that - probably due to small sample size - the results were not statistically significant. Specimen adequacy may be a determinant of a diagnostic agreement in renal allograft specimen assessment. While additional studies including larger case numbers are required to further delineate the impact of specimen adequacy on the reliability of histopathological assessments, specimen quality must be considered during clinical decision making while dealing with biopsy reports based on minimal or unsatisfactory specimens.

  1. Multiple-turnover cleavage of double-stranded DNA by sandwiched zinc-finger nuclease.

    Science.gov (United States)

    Mineta, Yusuke; Okamoto, Tomoyuki; Takenaka, Kosuke; Doi, Norio; Aoyama, Yasuhiro; Sera, Takashi

    2009-01-01

    To refine zinc-finger nuclease (ZFN) technology, we constructed a sandwiched ZFN, in which a DNA cleavage enzyme was sandwiched with two artificial zinc-finger proteins (AZPs). Because the sandwiched ZFN is designed to cleave the DNA between the two AZP-binding sites, the sandwiched ZFN is expected to bind preferentially to a DNA substrate rather than to cleavage products and thereby cleave it with multiple turnovers. To prove the concept, we sandwiched a staphylococcal nuclease (SNase), which cleaves DNA as a monomer, between two 3-finger AZPs. The AZP-sandwiched SNase cleaved large amounts of dsDNA site-specifically. Such multiple-turnover cleavage was not observed with control nucleases that possess a single AZP.

  2. Vickers Microhardness Testing with Miniaturized Disk Specimens

    OpenAIRE

    Kurishita, Hiroaki; Kayano, Hideo

    1991-01-01

    The microhardness technique has been increasingly important for testing irradiated materials because of the necessity of small-scale specimen technology. In order to establish Vickers microhardness testing over a wide temperature range using miniaturized specimens such as transmission electron microscopy (TEM) disks, an apparatus that permits the measurements in the temperature range of well below liquid nitrogen temperature to well above room temperature is developed. Effects of indentation ...

  3. Ultrasonic analysis of spherical composite test specimens

    Energy Technology Data Exchange (ETDEWEB)

    Brosey, W.D.

    1984-08-22

    Filament wound spherical test specimens have been examined ultrasonically as part of a program to determine the effectiveness of various nondestructive evaluation techniques for analysis of mechanical characteristics of a composite with enclosed geometry. The Kevlar-epoxy composite specimens contained simulated defect conditions which were located, and the extent of damage determined, using ultrasonic analysis. Effects of transducer frequency and signal parameters have been examined to determine optimum conditions for flaw detection. The data were displayed in rectangular and axonometric projection.

  4. Mechanics properties of paulownia core sandwich composites%泡桐木夹层结构材料的力学性能

    Institute of Scientific and Technical Information of China (English)

    方海; 刘伟庆; 陆伟东; 万里

    2011-01-01

    Green paulownia sandwich composite material was manufactured by using paulownia tree. The mechanics properties of paulownia were better than that of balsa wood except weight, and it was low-cost. The light-weight high-performance paulownia core sandwich composites were manufactured by vacuum infusion molding process. The sandwich beams with different ratios of span to thickness were researched by three-point and four-point flexural test. The typical failure modes and the mechanism of innovative sandwich specimens were investigated. The flexural stiffness and the ultimate bearing capacity of sandwich composites were studied by ordinary sandwich beam theory. The analysis result agreed well with test result. The design method was presented based on the intensity demand.%选用泡桐木为原料,制备出夹层结构用泡桐木绿色夹芯材料,其木质纤维具有天然蜂窝形状,结构类似于目前航空航天领域常用的蜂窝芯材;泡桐木芯材除密度略高于Balsa轻木外,其他力学性能测试指标均优于轻木,同时在价格上占有绝对的优势.采用真空导入成型工艺,成功制备出轻质高强的泡桐木夹层复合材料,通过不同跨高比试件的三点与四点弯试验,研究其典型受力破坏形态与机制;利用经典夹层梁理论预佑试件抗弯刚度和受弯极限承载力,理论值与实测值符合较好,并以此为基础,提出了基于强度的优化设计方法.

  5. Fabrication and Testing of Carbon Fiber Reinforced Truss Core Sandwich Panels

    Institute of Scientific and Technical Information of China (English)

    Bing Wang; Linzhi Wu; Li Ma; Qiang Wang; Shanyi Du

    2009-01-01

    Truss core sandwich panels reinforced by carbon fibers were assembled with bonded laminate facesheets and carbon fiber reinforced truss cores. The top and bottom facesheets were interconnected with truss cores. Both ends of the truss cores were embedded into four layers of top and bottom facesheets. The mechanical properties of truss core sandwich panels were then investigated under out-of-plane and in-plane compression loadings to reveal the failure mechanisms of sandwich panels. Experimental results indicated that the mechanical behavior of sandwich structure under in-plane loading is dominated by the buckling and debonding of facesheets.

  6. Fiber-Reinforced-Foam (FRF) Core Composite Sandwich Panel Concept for Advanced Composites Technologi

    Science.gov (United States)

    2010-01-01

    Fiber-Reinforced-Foam (FRF) Core Composite Sandwich Panel Concept for Advanced Composites Technologies Project - Preliminary Manufacturing Demonstration Articles for Ares V Payload Shroud Barrel Acreage Structure

  7. Giant magnetoresistance effect in Ni buffered Co/Cu/Co sandwich

    Institute of Scientific and Technical Information of China (English)

    LI; Tie(李铁)

    2002-01-01

    The effects of Ni buffer layer on the giant magnetoresistance structure of Co/Cu/Co sandwich are investigated systematically in this paper.It is found that Ni buffer layer can induce the crystallization of the lower Ni/Co layer and produce small coercivity,thus enlarging the difference in the magnetic behavior between the two magnetic layers in the sandwich.Moreover,the use of the Ni buffer layer can also improve the interface flatness in the sandwich.All these factors enhance the sensitivity of the Ni buffered sandwich.``

  8. Combined-load buckling behavior of metal-matrix composite sandwich panels under different thermal environments

    Science.gov (United States)

    Ko, William L.; Jackson, Raymond H.

    1991-01-01

    Combined compressive and shear buckling analysis was conducted on flat rectangular sandwich panels with the consideration of transverse shear effects of the core. The sandwich panel is fabricated with titanium honeycomb core and laminated metal matrix composite face sheets. The results show that the square panel has the highest combined load buckling strength, and that the buckling strength decreases sharply with the increases of both temperature and panel aspect ratio. The effect of layup (fiber orientation) on the buckling strength of the panels was studied in detail. The metal matrix composite sandwich panel was much more efficient than the sandwich panel with nonreinforced face sheets and had the same specific weight.

  9. Mechanical evaluation with fe analysis of sandwich panels for wind turbine blade

    Energy Technology Data Exchange (ETDEWEB)

    Yasaswi, M.; Naveen, P.N.E.; Prasad, R.V. [GIET. Dept. of Mechanical Engineering, Rajahmundry (India)

    2012-07-01

    Sandwich panels are notable for their structural efficiency and are used as load bearing components in various branches of engineering, especially in aerospace and marine industries. The objective of the present work is to perform computer-aided analysis on sandwich panels. The analysis of sandwich panel with truss core are compared with other four types of sandwich panel with continuous corrugated core, top hat core, zed core and channel core. The basic reason to use sandwich structure is to save weight, however smooth skins and excellent fatigue resistance are also attributes of a sandwich structure. A sandwich is comprised of two layered composite materials formed by bonding two or more thin facings or face sheets to relatively thick core materials. In this type of construction the facings resist nearly all of the in-plane loads and out-of-plane bending moments. The thin facings provide nearly all of the bending stiffness because they are generally of a much higher modulus material is located at a greatest distance from the neutral axis of the component. The basic concept of sandwich panel is that the facings carry the bending loads and the core carries the shear loads. The main function of the core material is to distribute local loads and stresses over large areas. From all this analysis it is concluded that the truss core Sandwich panels can be used in wind turbine blade design. (Author)

  10. Closeout of JOYO-1 Specimen Fabrication Efforts

    Energy Technology Data Exchange (ETDEWEB)

    ME Petrichek; JL Bump; RF Luther

    2005-10-31

    Fabrication was well under way for the JOYO biaxial creep and tensile specimens when the NR Space program was canceled. Tubes of FS-85, ASTAR-811C, and T-111 for biaxial creep specimens had been drawn at True Tube (Paso Robles, CA), while tubes of Mo-47.5 Re were being drawn at Rhenium Alloys (Cleveland, OH). The Mo-47.5 Re tubes are now approximately 95% complete. Their fabrication and the quantities produced will be documented at a later date. End cap material for FS-85, ASTAR-811C, and T-111 had been swaged at Pittsburgh Materials Technology, Inc. (PMTI) (Large, PA) and machined at Vangura (Clairton, PA). Cutting of tubes, pickling, annealing, and laser engraving were in process at PMTI. Several biaxial creep specimen sets of FS-85, ASTAR-811C, and T-111 had already been sent to Pacific Northwest National Laboratory (PNNL) for weld development. In addition, tensile specimens of FS-85, ASTAR-811C, T-111, and Mo-47.5 Re had been machined at Kin-Tech (North Huntington, PA). Actual machining of the other specimen types had not been initiated. Flowcharts 1-3 detail the major processing steps each piece of material has experienced. A more detailed description of processing will be provided in a separate document [B-MT(SRME)-51]. Table 1 lists the in-process materials and finished specimens. Also included are current metallurgical condition of these materials and specimens. The available chemical analyses for these alloys at various points in the process are provided in Table 2.

  11. Current rectification in nickelocenylferrocene sandwiched between two gold electrodes.

    Science.gov (United States)

    Matsuura, Yukihito

    2013-01-07

    I present a theoretical study of the electronic transport properties of nickelocenylferrocene sandwiched between gold electrodes. Compared with the biferrocene system, the nickelocenylferrocene system had high electrical conduction and rectification in the bias range -1 to 1 V. Furthermore, the spin-down states of the nickelocenylferrocene system exhibited perfect spin-filtering properties. From the electronic states of the nickelocenylferrocene, it was found that the rectification was caused by a difference in the bias-dependent behaviors between the Fe 3d and Ni 3d orbitals.

  12. A Conformal Thin-Sandwich Solver for Generic Initial Data

    CERN Document Server

    East, William E; Pretorius, Frans

    2012-01-01

    We present a new scheme for constructing initial data for the Einstein field equations using the conformal thin-sandwich formulation that does not assume conformal flatness or approximate Killing vectors. This includes a method for determining free data based on superposition, as well as a way to handle black hole singularities without excision. We numerically solve the constraint equations using a multigrid algorithm with mesh refinement. We demonstrate the efficacy of the method with initial data solutions for several applications: a quasi-circular binary black hole merger, a dynamical capture black hole-neutron star merger, and an ultrarelativistic collision.

  13. Standard Test Method for Dimensional Stability of Sandwich Core Materials

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2002-01-01

    1.1 This test method covers the determination of the sandwich core dimensional stability in the two plan dimensions. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given may be approximate. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  14. Standard Test Method for Shear Fatigue of Sandwich Core Materials

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2000-01-01

    1.1 This test method covers determination of the effect of repeated shear loads on sandwich core materials. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  15. Hydrogen storage property of sandwiched magnesium hydride nanoparticle thin film

    Energy Technology Data Exchange (ETDEWEB)

    Barcelo, Steven; Rogers, Matthew; Grigoropoulos, Costas P.; Mao, Samuel S. [Lawrence Berkeley National Laboratory and Department of Mechanical Engineering, University of California at Berkeley, Berkeley, CA 94720 (United States)

    2010-07-15

    Hydrogen sorption property of magnesium (Mg) in the form of sandwiched Pd/Mg/Pd films is investigated. Pulsed laser deposition method was applied to deposit the samples consisting of films of nanoparticles. The enthalpy of formation of MgH{sub 2} was found to be -68 kJ/mol H{sub 2} for films with nanoparticle size on the order of 50 nm, which is smaller than the value for bulk MgH{sub 2} and may be explained by the concept of excess volume. (author)

  16. Optimization of the curing process of a sandwich panel

    Science.gov (United States)

    Phyo Maung, Pyi; Tatarnikov, O.; Malysheva, G.

    2016-10-01

    This study presented finite element modelling and experimental measurements of temperatures during the autoclave curing of the T-50 aircraft wing sandwich panel. This panel consists of upper and lower carbon fibre based laminates and an aluminium foil honeycomb. The finite element modelling was performed using the Femap-Nastran product. During processing, the temperature at various points on the surface of the panel was measured using the thermocouples. The finite element method simulated the thermal conditions and determined the temperatures in the different parts of the panel for a full cycle of the curing process. A comparison of the calculated and experimental data shows that their difference does not exceed 6%.

  17. Devices, systems, and methods for conducting sandwich assays using sedimentation

    Energy Technology Data Exchange (ETDEWEB)

    Schaff, Ulrich Y; Sommer, Gregory J; Singh, Anup K; Hatch, Anson V

    2015-02-03

    Embodiments of the present invention are directed toward devices, systems, and method for conducting sandwich assays using sedimentation. In one example, a method includes generating complexes on a plurality of beads in a fluid sample, individual ones of the complexes comprising a capture agent, a target analyte, and a labeling agent. The plurality of beads including the complexes may be transported through a density media, wherein the density media has a density lower than a density of the beads and higher than a density of the fluid sample, and wherein the transporting occurs, at least in part, by sedimentation. Signal may be detected from the labeling agents of the complexes.

  18. Experimental Investigations of Compressed Sandwich Composite/Honeycomb Cylindrical Shells

    Science.gov (United States)

    Muc, A.; Stawiarski, A.; Romanowicz, P.

    2017-06-01

    This article explains in some details the behaviour of thick, deep cylindrical sandwich panels subjected to compressive loads. In general, experimental results indicated that two different forms of failure have been observed - the first corresponds to the overall buckling and the second to the facesheet wrinkling. The obtained experimentally damages of shells are verified and validated with the use of the FE analysis, 2-D and 3-D both in the linear and non-linear approach. The unidirectional strain gauges were applied to detect the initiation of the overall buckling mode.

  19. FINITE ELEMENT MODELING OF THIN CIRCULAR SANDWICH PLATES DEFLECTION

    Directory of Open Access Journals (Sweden)

    K. S. Kurachka

    2014-01-01

    Full Text Available A mathematical model of a thin circular sandwich plate being under the vertical load is proposed. The model employs the finite element method and takes advantage of an axisymmetric finite element that leads to the small dimension of the resulting stiffness matrix and sufficient accuracy for practical calculations. The analytical expressions for computing local stiffness matrices are found, which can significantly speed up the process of forming the global stiffness matrix and increase the accuracy of calculations. A software is under development and verification. The discrepancy between the results of the mathematical model and those of analytical formulas for homogeneous thin circularsandwich plates does not exceed 7%.

  20. Optical and thermophysical parameters measurement using sandwich photodetectors

    Science.gov (United States)

    Turinov, Valery I.

    1993-12-01

    A method is reported for estimating thermophysical and optical parameters, in which a two- spectral band sandwich photodetector is used. The sensitivity ranges of such a sensor are 2 - 5 micrometers and 8 - 14 micrometers . On irradiating an object's surface by a short radiation pulse the photodetector collected signals U1, U2 and the rates of their changes (dU1/dt), (dU2/dt) are recorded. These pertain to the same area on the object's surface and belong to the two spectral ranges mentioned. The parameters of the object are evaluated by means of calculations with the values measured.

  1. The Value of Agricultural Voucher Specimens

    OpenAIRE

    Barkworth,Mary; Wolf, Paul; Kinosian,Sylvia; Dyreson, Curtis; Pearse, Will; Brandt, Ben; Cobb,Neil

    2017-01-01

    Voucher specimens are the ultimate raw data of biodiversity studies because they document the interpretation of the names used in papers and reports resulting from such studies. The value of voucher specimens is increased by making their records web-accessible but they can be further enhanced by linking them to other online resources, particularly if the links are birectional.  In this presentation, we discuss the potential benefits of such links for a group of agricultural significance, the ...

  2. A Z_m Ham Sandwich Theorem for Complex Measures

    CERN Document Server

    Simon, Steven

    2010-01-01

    A "ham sandwich" theorem is derived for n complex measures on C^n. For each integer m >= 2, a complex hyperplane H and m corresponding "1/m" sectors are found, satisfying the condition that the "rotational average" of the measures of these sectors is zero. The result can be seen as a kind of rotational equipartition of each measure by a regular "m-fan". The proof of the theorem is topological, based on a Z_m version of the Borsuk-Ulam theorem for punctured (2n - 1)-spheres in C^n. Any finite real measure on R^{2n} can be seen as a type of complex measure on C^n, so the theorem can be applied to n finite measures on R^{2n}. In the case that m = 3, this shows the existence of a regular 3-fan which trisects each of the n measures. Similarly, any pair of finite real measures on R^{2n} can be naturally identified with a complex measure on C^n, so the theorem applies to 2n finite measures on R^{2n}. This yields a rotational condition on pairs of finite measures, and the original ham sandwich theorem for R^{2n} is r...

  3. Plasmonic nanomesh sandwiches for ultrathin film silicon solar cells

    Science.gov (United States)

    Gao, Tongchuan; Wang, Baomin; Leu, Paul W.

    2017-02-01

    We theoretically investigate the strategy of integrating metal nanoparticles (NPs)/nanomeshes (NMs) into the top and/or bottom of crystalline silicon (c-Si) thin film solar cells for light trapping and enhanced carrier collection. C-Si thin films exhibit absorption resonances corresponding to Fabry-Pérot modes. Frontside metal NPs enhance absorption by additionally coupling light into localized surface plasmon resonances and c-Si waveguide modes, while a frontside metal NM increases absorption by coupling light into surface plasmon polaritons and c-Si waveguide modes. The frontside metal NM also functions as a flexible top electrode, which may replace conventional brittle transparent conductive oxide thin films. The backside metal NM exhibits enhanced absorption due to the coupling of light into c-Si waveguide modes and the cavity modes within the holes of metal NM. We illustrate how the optimal metal NM sandwich, consisting of NMs on both sides of a 300 nm thick c-Si with an appropriate antireflection coating (ARC), achieves a 72.9% enhancement in short-circuit current density compared with that of a 300 nm thick c-Si thin film solar cell with 100 nm thick Si3N4 ARC and 300 nm thick Ag back reflector. The current generation in the metal NM sandwich is more in the center of the thin film such that there should be less surface recombination. The uniform current generation throughout the film results in less overall recombination.

  4. Dispersion of guided waves in composite laminates and sandwich panels

    Science.gov (United States)

    Schaal, Christoph; Mal, Ajit

    2015-03-01

    In composite structures, damages are often invisible from the surface and can grow to reach a critical size, potentially causing catastrophic failure of the entire structure. Thus safe operation of these structures requires careful monitoring of the initiation and growth of such defects. Ultrasonic methods using guided waves offer a reliable and cost-effective method for structural health monitoring in advanced structures. Guided waves allow for long monitoring ranges and are very sensitive to defects within their propagation path. In this work, the relevant properties of guided Lamb waves for damage detection in composite structures are investigated. An efficient numerical approach is used to determine their dispersion characteristics, and these results are compared to those from laboratory experiments. The experiments are based on a pitch-catch method, in which a pair of movable transducers is placed on one surface of the structure to induce and detect guided Lamb waves. The specific cases considered include an aluminum plate and an aluminum honeycomb sandwich panel with woven composite face sheets. In addition, a disbond of the interface between one of the face sheets and the honeycomb core of the sandwich panel is also considered, and the dispersion characteristics of the two resultant waveguides are determined. Good agreement between numerical and experimental dispersion results is found, and suggestions on the applicability of the pitch-catch system for structural health monitoring are made.

  5. Free Vibration and Hardening Behavior of Truss Core Sandwich Beam

    Directory of Open Access Journals (Sweden)

    J. E. Chen

    2016-01-01

    Full Text Available The dynamic characteristics of simply supported pyramidal truss core sandwich beam are investigated. The nonlinear governing equation of motion for the beam is obtained by using a Zig-Zag theory. The averaged equations of the beam with primary, subharmonic, and superharmonic resonances are derived by using the method of multiple scales and then the corresponding frequency response equations are obtained. The influences of strut radius and core height on the linear natural frequencies and hardening behaviors of the beam are studied. It is illustrated that the first-order natural frequency decreases continuously and the second-order and third-order natural frequencies initially increase and then decrease with the increase of strut radius, and the first three natural frequencies all increase with the rise of the core height. Furthermore, the results indicate that the hardening behaviors of the beam become weaker with the increase of the rise of strut radius and core height. The mechanisms of variations in hardening behavior of the sandwich beam with the three types of resonances are detailed and discussed.

  6. Immunometric Double-Antibody Sandwich Enzyme-Linked Immunosorbent Assay.

    Science.gov (United States)

    Kohl, Thomas O; Ascoli, Carl A

    2017-06-01

    The double-antibody sandwich enzyme-linked immunosorbent assay (ELISA) is preferentially used to determine the concentration of unknown antibody in a sample. Pure antigen is not required in this assay; however, the use of a reporter-labeled detection antibody is essential. The double-antibody sandwich ELISA is suitable for epitope mapping of different monoclonal antibodies that have been generated against a single antigen. First, plates are coated with a capture antibody specific for immunoglobulins generated by immunization of a host species. Next, the test antibody solution (e.g., serum) is incubated with the capture antibody to facilitate binding. The plates are washed to remove unbound antibody, and then antigen is added. The plates are washed again followed by the addition of an antigen-specific reporter-labeled antibody. Following incubation, unbound reporter antibody is washed off, and reporter-specific substrate is added. Reporter-mediated substrate hydrolysis is visualized and measured. The signal is proportional to the number of test antibodies present in the serum. © 2017 Cold Spring Harbor Laboratory Press.

  7. Impact Delamination and Fracture in Aluminum/Acrylic Sandwich Plates

    Science.gov (United States)

    Liaw, Benjamin; Zeichner, Glenn; Liu, Yanxiong; Bowles, Kenneth J. (Technical Monitor)

    2000-01-01

    Impact-induced delamination and fracture in 6061-T6 aluminum/cast acrylic sandwich plates adhered by epoxy were generated in an instrumented drop-weight impact machine. Although only a small dent was produced on the aluminum side when a hemispherical penetrator tup was dropped onto it from a couple of inches, a large ring of delamination at the interface was observed. The delamination damage was often accompanied by severe shattering in the acrylic substratum. Damage patterns in the acrylic layer include radial and ring cracks and, together with delamination at the interface, may cause peeling-off of acrylic material from the sandwich plate. Theory of stress-wave propagation can be used to explain these damage patterns. The impact tests were conducted at various temperatures. The results also show clearly that temperature effect is very important in impact damage. For pure cast acrylic nil-ductile transition (NDT) occurs between 185-195 F. Excessive impact energy was dissipated into fracture energy when tested at temperature below this range or through plastic deformation when tested at temperature above the NDT temperature. Results from this study will be used as baseline data for studying fiber-metal laminates, such as GLARE and ARALL for advanced aeronautical and astronautical applications.

  8. Modelling of Debond and Crack Propagation in Sandwich Structures Using Fracture and Damage Mechanics

    DEFF Research Database (Denmark)

    Berggreen, C.; Simonsen, Bo Cerup; Toernqvist, Rikard

    2003-01-01

    Skin-core de-bonding or core crack propagation will often be dominating mechanisms in the collapse modes of sandwich structures. This paper presents two different methods for prediction of crack propagation in a sandwich structure: a fracture mechanics approach, where a new mode-mix method...

  9. Failure Investigation of Debonded Sandwich Columns: An Experimental and Numerical Study

    DEFF Research Database (Denmark)

    Moslemian, Ramin; Berggreen, Christian; Carlsson, Leif A.

    2009-01-01

    Failure of compression loaded sandwich columns with an implanted through-width face/core debond is examined. Compression tests were conducted on sandwich columns containing implemented face/core debonds. The strains and out-of-plane displacements of the debonded region were monitored using the di...

  10. Research overview of design method of super light multi-hole class- honeycomb sandwich structure materials

    Directory of Open Access Journals (Sweden)

    Xiang LI

    Full Text Available With the sandwich structure materials' application and promotion in the field of engineering continuously, existing sandwich structure material gradually cannot meet the design requirements. It is very urgent to develop new sandwich structure materials of high efficiency, energy saving and easy to process. The project puts forward and constructs a new kind of class-honeycomb sandwich structure material combined with important application backgrounds that super light and high strength metal sandwich structure materials are applied into the high weight and high energy consumption equipments of automobile, aerospace and machinery and so on. This research involve: mechanical properties equivalent method for the class-honeycomb sandwich structure and its core; Strength, stiffness and inherent frequency characteristic and failure criterions of the class-honeycomb sandwich structure; based on the failure criterions constructing the multiple-constraint models of the class-honeycomb sandwich structure. The research tries to put forward a new method for innovative design of lightweight material and structure and new ideas of lightweight technology research in theory and practice.

  11. Real-time X-ray investigation of aluminum foam sandwich production

    Energy Technology Data Exchange (ETDEWEB)

    Banhart, J.; Stanzick, H. [Fraunhofer-Inst. for Advanced Materials, Bremen (Germany); Helfen, L.; Baumbach, T. [Fraunhofer-Inst. for Non-Destructive Testing, Dresden (Germany); Nijhof, K. [Honsel-Werke AG, Meschede (Germany)

    2001-06-01

    The authors study the foaming behavior of Al-based sandwich panels using X-ray radioscopy. X-ray radioscopy is a suitable tool for observing the metal foaming process in general and the production of aluminum foam sandwich panels in particular. The internal structure of the foam can be resolved clearly. (orig.)

  12. A Phloem Sandwich Unit for Observing Bark Beetles, Associated Predators, and Parasites

    Science.gov (United States)

    Donald N. Kim; Mitchel C. Miller

    1981-01-01

    This paper describes a phloem sandwich that allows observation of parent beetles, their brood, and associates within the inner bark, and permits observation of predator and parasite behavior on the bark surface. The construction of the unit permits the introduction of multiple pairs of beetles into a single sandwich.

  13. Sandwich Magnetoelectric Composites of Polyvinylidene Fluoride, Tb-Dy-Fe Alloy, and Lead Zirconate Titanate

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The novel sandwich composites were prepared by sandwiching a polyvinylidene fluoride/Tb-Dy-Fe alloy composite (PVDF/Terfenol-D) between polyvinylidene fluoride/lead zirconate titanate composites(PVDF/PZT). The maximum magnetoelectric effect voltage coefficient, (dE/dH)33max, of the sandwich composites is higher than that of three-phase composites at their own optimal loading level of Terfenol-D. This is attributed to less interface relaxations of strain and better polarization of the sandwich composites. When the volume fraction of Terfenol-D is higher than 0.10, no coupling interaction for three-phase composites could intensity, the magnetoelectric effect voltage coefficient, (dE/dH)33, of sandwich composites is higher than that of three-phase composites; at low magnetic field intensity, (dE/dH)33 of sandwich composites is lower than that of three-phase composites. At their resonance frequency, the (dE/dH)33max of the sandwich composites and the dH)33max at resonance frequency confirms the improvement of maximum magnetoelectric effect coefficient via sandwich-structured composites.

  14. PMI Foam Cored Sandwich Components Produced by Means of Different Manufacturing Methods

    Institute of Scientific and Technical Information of China (English)

    Leonhard Maier; HU Pei; Herman Seibert

    2006-01-01

    The paper introduced the structural applications with PMI (Polymethacrylimide) foams in sandwich components for rotor craft, launching vehicle and civil aircraft and discuss some typically used manufacturing methods, such as e. g.in-mould pressing, autoclave curing and resin infusion. The advantages of foam-cored sandwich design versus honeycombcored design will be discussed, focussing on manufacturing costs.

  15. Failure Investigation of Debonded Sandwich Columns: An Experimental and Numerical Study

    DEFF Research Database (Denmark)

    Moslemian, Ramin; Berggreen, Christian; Carlsson, Leif A.

    2009-01-01

    Failure of compression loaded sandwich columns with an implanted through-width face/core debond is examined. Compression tests were conducted on sandwich columns containing implemented face/core debonds. The strains and out-of-plane displacements of the debonded region were monitored using the di...

  16. Experimental validation of the Higher-Order Theory approach for sandwich panels with flexible core materials

    NARCIS (Netherlands)

    Straalen, IJ.J. van

    2000-01-01

    During tthe 1990's the higher-order theory was developed by Frostig to enable detailed stress analyses of sandwich panel structures. To investigate the potentials of this approach experiments are performed on sandwich panels made of thin steel faces and mineral wool or polystyrene core material. A p

  17. Weld nugget formation in resistance spot welding of new lightweight sandwich material

    DEFF Research Database (Denmark)

    Sagüés Tanco, J.; Nielsen, Chris Valentin; Chergui, Azeddine

    2015-01-01

    Weldability of a new lightweight sandwich material, LITECOR®, by resistance spot welding is analyzed by experiments and numerical simulations. The spot welding process is accommodated by a first pulse squeezing out the non-conductive polymer core of the sandwich material locally to allow metal–me...

  18. Robust and Air-Stable Sandwiched Organo-Lead Halide Perovskites for Photodetector Applications

    KAUST Repository

    Mohammed, Omar F.

    2016-02-25

    We report the simplest possible method to date for fabricating robust, air-stable, sandwiched perovskite photodetectors. Our proposed sandwiched structure is devoid of electron or hole transporting layers and also the expensive electrodes. These simpler architectures may have application in the perovskite-only class of solar cells scaling up towards commercialization.

  19. 16 CFR Figure 6 to Subpart A of... - Dummy Specimen in Specimen Holder

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Dummy Specimen in Specimen Holder 6 Figure 6 to Subpart A of Part 1209 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT REGULATIONS INTERIM SAFETY STANDARD FOR CELLULOSE INSULATION The Standard Pt. 1209, Subpt. A...

  20. Innovative sandwich concepts open up potential for flat structures. Function-integrated lightweight design; Sandwich-Strukturen fuer den funktionsintegrierten Leichtbau. Fahrzeugleichtbau

    Energy Technology Data Exchange (ETDEWEB)

    Kopp, Gerhard; Friedrich, Horst E. [DLR Deutsches Zentrum fuer Luft- und Raumfahrt e.V., Stuttgart (Germany). Inst. fuer Fahrzeugkonzepte; Kuppinger, Jan [Fraunhofer-Institut fuer Chemische Technologie (ICT), Pfinztal (Germany). Abt. Polymer-Engineering; Henning, Frank [Fraunhofer-Institut fuer Chemische Technologie (ICT), Pfinztal (Germany). Abt. Polymer-Engineering; DLR Deutsches Zentrum fuer Luft- und Raumfahrt e.V., Stuttgart (Germany). Kompetenzzentrum; Karlsruher Innovationsclusters ' Technologien fuer den hybriden Leichtbau' (Germany)

    2009-07-01

    Sandwich structures make it possible to achieve an optimum combination of material, form and functional lightweight design. Vehicle weight is reduced and resources are saved. However, such solutions can only be used when the overall concept is cost-effective. For this reason, various DLR and Fraunhofer institutes are currently working on new and cost-effective sandwich structures within the 'Competence Centre for Automotive Lightweight Technology' to further exploit this construction method for flat structures. (orig.)

  1. A Novel Sandwich-type Dinuclear Complex for High-capacity Hydrogen Storage%A Novel Sandwich-type Dinuclear Complex for High-capacity Hydrogen Storage

    Institute of Scientific and Technical Information of China (English)

    朱海燕; 陈元振; 李赛; 曹秀贞; 柳永宁

    2012-01-01

    From density functional theory (DFT) calculations, we predicted that the sandwich-type dinuclear organometallic compounds Cpffi2 and Cp2Sc2 can adsorb up to eight hydrogen molecules respectively, corresponding to a high gravimetric storage capacity of 6.7% and 6.8% (w), respectively. These sandwich-type organometallocenes proposed in this work are favorable for reversible adsorption and desorption of hydrogen at ambient conditions.

  2. 37 CFR 2.56 - Specimens.

    Science.gov (United States)

    2010-07-01

    ... indicate membership in the collective organization. (5) A certification mark specimen must show how a... of a union or other organization performed the work or labor on the goods or services. (c) A... be a digitized image in .jpg or .pdf format....

  3. Influence of Si buffer layer on the giant magnetoresistance effect in Co/Cu/Co sandwiches

    Institute of Scientific and Technical Information of China (English)

    李冠雄; 沈鸿烈; 沈勤我; 李铁; 邹世昌

    2000-01-01

    The Co/Cu/Co sandwiches with a semiconductor Si buffer layer were prepared by high vacuum electron-beam evaporation. The influence of the Si buffer layer with different thickness on the giant magnetoresistance (GMR) effect in the Co/Cu/Co sandwiches was investigated. It was found that the GMR showed an obvious anisotropy when the thickness of Si buffer layer was larger than or equal to 0.9 nm, and that the GMR was basically isotropic with an Si buffer layer thinner than 0.9 nm. The anisotropic behavior of GMR can be ascribed to the in-plane magnetic anisotropy in the sandwiches. Due to the interdiffusion at the Si buffer/Co interface, a Co2Si interface layer with a good (301) texture formed and induced the in-plane magnetic anisotropy in the sandwiches. The dependence of the crystalline texture of the sandwiches on the thickness of Si buffer layer was also studied.

  4. Unidirectional cloning by cleaving heterogeneous sites with a single sandwiched zinc finger nuclease.

    Science.gov (United States)

    Shinomiya, Kazuki; Mori, Tomoaki; Aoyama, Yasuhiro; Sera, Takashi

    2011-11-04

    We previously developed a novel type of zinc finger nucleases (ZFNs), sandwiched ZFNs that can discriminate DNA substrates from cleavage products and thus cleave DNA much more efficiently than conventional ZFNs as well as perform with multiple turnovers like restriction endonucleases. In the present study, we used the sandwiched ZFN to unidirectionally clone exogenous genes into target vectors by cleaving heterogeneous sites that contained heterogeneous spacer DNAs between two zinc-finger protein binding sites with a single sandwiched ZFN. We demonstrated that the sandwiched ZFN cleaved a 40-fold excess of both insert and vector plasmids within 1h and confirmed by sequencing that the resulting recombinants harbored the inserted DNA fragment in the desired orientation. Because sandwiched ZFNs can recognize and cleave a variety of long (≥ 26-bp) target DNAs, they may not only expand the utility of ZFNs for construction of recombinant plasmids, but also serve as useful meganucleases for synthesis of artificial genomes.

  5. An Optimum Analysis Method of Sandwich Structures Made from Elastic-viscoelastic Materials

    Institute of Scientific and Technical Information of China (English)

    CHEN Ying-bo; XIA Yu; REN Zhi-gang; LU Zhe-an; WANG Er-lei

    2004-01-01

    Due to a viscoelastic damping middle layer,sandwich structures have the capacity of energy consumption.In this paper,we describe the frequency-dependent property of viscoelastic materials using complex modulus model,and iterative modal strain energy method and iterative complex eigenvalue method are presented to obtain frequency and loss factor of sandwich structures.The two methods are effective and exact for the large-scale complex composite sandwich structures.Then an optimum analysis method is suggested to apply to sandwich structures.Finally,as an example,an optimum analysis of a clamped-clamped sandwich beams is conducted,theoretical closed-form solution and numerical predictions are studied comparatively,and the results agree well.

  6. Natural Cork Agglomerate Employed as an Environmentally Friendly Solution for Quiet Sandwich Composites

    Science.gov (United States)

    Sargianis, James; Kim, Hyung-ick; Suhr, Jonghwan

    2012-01-01

    Carbon fiber-synthetic foam core sandwich composites are widely used for many structural applications due to their superior mechanical performance and low weight. Unfortunately these structures typically have very poor acoustic performance. There is increasingly growing demand in mitigating this noise issue in sandwich composite structures. This study shows that marrying carbon fiber composites with natural cork in a sandwich structure provides a synergistic effect yielding a noise-free sandwich composite structure without the sacrifice of mechanical performance or weight. Moreover the cork-core sandwich composites boast a 250% improvement in damping performance, providing increased durability and lifetime operation. Additionally as the world seeks environmentally friendly materials, the harvesting of cork is a natural, renewable process which reduces subsequent carbon footprints. Such a transition from synthetic foam cores to natural cork cores could provide unprecedented improvements in acoustic and vibrational performance in applications such as aircraft cabins or wind turbine blades. PMID:22574250

  7. Structural Behaviour of Precast Lightweight Foamed Concrete Sandwich Panel under Axial Load: An Overview

    Directory of Open Access Journals (Sweden)

    Suryani Samsudin

    2013-02-01

    Full Text Available The development of precast sandwich concrete has gained acceptance worldwide in conjunction with the Industrial Building System (IBS.  The advancement and improvement of using wall panel has gone through a lot of achievements through the last decade. The usage of precast lightweight sandwich panel has become the alternative to conventional construction using brick wall. The usage of this panel system contributes to a sustainable and environmental friendly construction.  This paper presents an overview of the latest development in precast concrete sandwich panel as an IBS. The purpose of this paper is to provide comprehensive information on latest research development of sandwich panel for building construction purposes. The information on sandwich panel’s composition, material, properties, strength, availability, and its usage as structural element are reported.  An innovative concept used in the design of these systems and the use of lightweight materials is also discussed.

  8. Analysis and Behaviour of Sandwich Panels with Profiled Metal Facings under Transverse Load

    Directory of Open Access Journals (Sweden)

    M. Budescu

    2004-01-01

    Full Text Available Sandwich panels with thin steel facings and polyurethane core combine the load-carrying capacity of metal facings and protection functions with core properties. The core separates the two facings and keeps them in a stable condition, transmits shear between external layers, provides most of the shear rigidity and occasionally makes of useful contribution to the bending stiffness of the sandwich construction as a whole [1]. An experimental program on sandwich panels has been organized to prove that the mechanical properties of core and interface satisfy the load-carrying requirements for structural sandwich panels. The analysis of sandwich panels with deep profiles facings for cladding elements, respectively the roof constructions, has been carried out according to the European design norms [1], [5].

  9. Computed tomography with single-shot dual-energy sandwich detectors

    Science.gov (United States)

    Kim, Seung Ho; Youn, Hanbean; Kim, Daecheon; Kim, Dong Woon; Jeon, Hosang; Kim, Ho Kyung

    2016-03-01

    Single-shot dual-energy sandwich detector can produce sharp images because of subtraction of images from two sub-detector layers, which have different thick x-ray converters, of the sandwich detector. Inspired by this observation, the authors have developed a microtomography system with the sandwich detector in pursuit of high-resolution bone-enhanced small-animal imaging. The preliminary results show that the bone-enhanced images reconstructed with the subtracted projection data are better in visibility of bone details than the conventionally reconstructed images. In addition, the bone-enhanced images obtained from the sandwich detector are relatively immune to the artifacts caused by photon starvation. The microtomography with the single-shot dual-energy sandwich detector will be useful for the high-resolution bone imaging.

  10. Rehydration of forensically important larval Diptera specimens.

    Science.gov (United States)

    Sanford, Michelle R; Pechal, Jennifer L; Tomberlin, Jeffery K

    2011-01-01

    Established procedures for collecting and preserving evidence are essential for all forensic disciplines to be accepted in court and by the forensic community at large. Entomological evidence, such as Diptera larvae, are primarily preserved in ethanol, which can evaporate over time, resulting in the dehydration of specimens. In this study, methods used for rehydrating specimens were compared. The changes in larval specimens with respect to larval length and weight for three forensically important blow fly (Diptera: Calliphoridae) species in North America were quantified. Phormia regina (Meigen), Cochliomyia macellaria (F.), and Chrysomya rufifacies (Macquart) third-instar larvae were collected from various decomposing animals and preserved with three preservation methods (80% ethanol, 70% isopropyl alcohol, and hot-water kill then 80% ethanol). Preservative solutions were allowed to evaporate. Rehydration was attempted with either of the following: 80% ethanol, commercial trisodium phosphate substitute solution, or 0.5% trisodium phosphate solution. All three methods partially restored weight and length of specimens recorded before preservation. Analysis of variance results indicated that effects of preservation, rehydration treatment, and collection animal were different in each species. The interaction between preservative method and rehydration treatment had a significant effect on both P. regina and C. macellaria larval length and weight. In addition, there was a significant interaction effect of collection animal on larval C. macellaria measurements. No significant effect was observed in C. rufifacies larval length or weight among the preservatives or treatments. These methods could be used to establish a standard operating procedure for dealing with dehydrated larval specimens in forensic investigations.

  11. Effect of Processing Conditions on Fracture Resistance and Cohesive Laws of Binderfree All-Cellulose Composites

    DEFF Research Database (Denmark)

    Goutianos, Stergios; Arévalo, R.; Sørensen, Bent F.

    2014-01-01

    microscope to a) perform accurate measurements of both the fracture energy for crack initiation and the fracture resistance and b) observe the microscale failure mechanisms especially in the the wake of the crack tip. Since the mechanical behaviour of the all-cellulose composites was non-linear, a general...... method was first developed to obtain fracture resistance values from the DCB specimens taking into account the non-linear material response. The binderfree all-cellulose composites were prepared by a mechanical refinement process that allows the formation of intramolecular bonds between the cellulose......The fracture properties of all-cellulose composites without matrix were studied using Double Cantilever Beam (DCB) sandwich specimens loaded with pure monotonically increasing bending moments, which give stable crack growth. The experiments were conducted in an environmental scanning electron...

  12. Left ventricle remodelling by double-patch sandwich technique

    Directory of Open Access Journals (Sweden)

    Nocchi Andrea

    2007-01-01

    Full Text Available Abstract Background The sandwich double-patch technique was adopted as an alternative method for reconstruction of the left ventricle after excision of postinfarction dysfunctional myocardium to solve technical problems due to the thick edges of the ventricular wall. Methods Over a 5-year period, 12 of 21 patients with postinfarction antero-apical left ventricular aneurysm had thick wall edges after wall excision. It was due to akinetic muscular thick tissue in 6 cases, while in the other 6 with classic fibrous aneurysm, thick edges remained after the cut of the border zone. The ventricular opening was sandwiched between two patches and this is a technique which is currently used for the treatment of the interventricular septum rupture. In our patients the patches are much smaller than the removed aneurysm and they were sutured simply by a single row of single stitches. However, in contrast to interventricular septum rupture where the patches loosen the tension of the tissues, in our patients the patches pull strongly and restrain the walls by fastening their edges and supporting tight stitches. In this way they could narrow the cavity and close the ventricle. Results The resected area varied from 5 × 4 to 8 × 8 cm. Excision was extended into the interventricular septum in 5 patients, thus opening the right ventricle. CABG was performed on all patients but two. Left ventricular volumes and the ejection fraction changed significantly: end-systolic volume 93.5 ± 12.4 to 57.8 ± 8.9 ml, p Conclusion The double-patch sandwich technique (bi-patch closure offers some advantages and does not result in increased morbidity and mortality. In the case of excising a left ventricular aneurysm, this technique in no way requires eversion of the edges, felt strips, buttressed and multiple sutures, all of which are needed for longitudinal linear closure. Moreover, it does not require purse string sutures, endocardial scar remnant to secure the patch or

  13. Utilization of bagasse and coconut fibers waste as fillers of sandwich composite for bridge railway sleepers

    Science.gov (United States)

    Soehardjo, K. A.; Basuki, A.

    2017-07-01

    The bridge railway sleepers is an essential component in the construction of railways, as the foundation of the rail support in order to withstand the load a train that runs above it. Sleepers used in bridge construction are expected to have a longer service life, lighter weight and durable so that can be used more efficient. This research was carried out to create a model of bridges railway sleepers made of sandwich structured composite from fiber glass, epoxy resin with fillers waste of bagasse (sugar cane pulp mill) or coconut fiberboard (copra industry) that using polyurethane as an adhesive. The process of making was conditioned for small and medium industrial applications. Railway sleepers’ specifications adapted to meet the requirements of end user. The process steps in this research include; lay-up fiberglass combined with bagasse/coconut fiberboard (as fillers), gluing with epoxy resin, molded it with pressure to be solid, curing after solidification process. The specimens of composite, bagasse and coconut fiber board were tested for tensile and compressive strength. The prototype were tested of mechanical test: flexural moment test to the stand rail, flexural moment test to the middle of the sleepers and tensile strength test on one side of the sleepers, in accordance to SNI 11-3388-1994 Method testing of single block concrete sleepers and bearing single rail fastening systems. The results of mechanical testing all variations meet the technical specifications of end user such as test results for flexural moment on all prototypes, after load test, there is no visible crack. While in the tensile strength test, it seem the prototype with coconut fiberboard filler, shows better performance than bagasse fiberboard filler, the decisions is just depended on techno economic and lifetime.

  14. Breast specimen shrinkage following formalin fixation

    Directory of Open Access Journals (Sweden)

    Horn CL

    2014-02-01

    Full Text Available Christopher L Horn, Christopher Naugler Department of Pathology and Laboratory Medicine, University of Calgary, and Calgary Laboratory Services, Calgary, AB, Canada Abstract: Accurate measurement of primary breast tumors and subsequent surgical margin assessment is critical for pathology reporting and resulting patient therapy. Anecdotal observations from pathology laboratory staff indicate possible shrinkage of breast cancer specimens due to the formalin fixation process. As a result, we conducted a prospective study to investigate the possible shrinkage effects of formalin fixation on breast cancer specimens. The results revealed no significant changes in tumor size, but there were significant changes in the distance to all surgical resection margins from the unfixed to fixed state. This shrinkage effect could interfere with the accuracy of determining distance to margin assessment and tumor-free margin assessment. Thus, changes in these measurements due to the formalin fixation process have the potential to alter treatment options for the patient. Keywords: breast margins, formalin, shrinkage, cancer

  15. Is routine histopathology of tonsil specimen necessary?

    Directory of Open Access Journals (Sweden)

    Agida S Adoga

    2011-01-01

    Full Text Available Background: Tonsillar diseases are common in paediatric and adult otolaryngological practice. These diseases require tonsillectomy. Specimens are subjected to histopathology routinely in my institution for fear of infections and tumour without consideration for risk factors. The financial burden is on the patients and waste of histopathologist′s man hour because other specimens are left un-attended. This study aims to find out the necessity of routine histopathology of tonsil specimens. Materials and Methods : A 2 year retrospective review of the histopathological results of two (paediatric and adult groups of 61 patients managed for tonsillar diseases at the ENT UNIT of Jos University Teaching Hospital from July 2005 to June, 2007. Data extracted included biodata, clinical features and histopathological diagnosis. Result : The 61 patients comprise 35 children and 26 adults. The youngest and oldest paediatric patients were 1 year and 3 months and 16 years respectively, a range of 1 year 3 months to 16 years. The youngest and oldest adults were 17 and 50 years with a range of 17-50 years. Groups mean ages were 5.1 and 28.5 years. The gender ratios were 1:2.7 and 1:1.9 respectively. One adult was HIV positive. The histopathological diagnosis were chronic nonspecific tonsillitis in 10(16.6%, follicular tonsillitis in 23(38.3%, chronic suppurative tonsillitis in 10(16.6%, lymphoid hyperplasia in 18(30.0% and lymphoma in 1(1.0% respectively. Conclusion : Histopathologic request for tonsillectomy specimens should be based on certain risk factors with consideration of the cost to patients and to spare the histopathologist′s man hour.

  16. SQA specimen paper 2013, national 5, French

    CERN Document Server

    SQA

    2013-01-01

    Practise for your exam on the offical National 5 specimen paper from the Scottish Qualifications Authority. Plus each book includes additional model papers and extra revision guidance, making them an essential purchase for any student.; Discover how to get your best grade with answers checked by senior examiners.; Prepare for your exams with study skills guidance sections.; Gain vital extra marks and avoid common mistakes with examiner tips

  17. Damage modeling in Small Punch Test specimens

    DEFF Research Database (Denmark)

    Martínez Pañeda, Emilio; Cuesta, I.I.; Peñuelas, I.

    2016-01-01

    Ductile damage modeling within the Small Punch Test (SPT) is extensively investigated. The capabilities ofthe SPT to reliably estimate fracture and damage properties are thoroughly discussed and emphasis isplaced on the use of notched specimens. First, different notch profiles are analyzed...... and constraint conditionsquantified. The role of the notch shape is comprehensively examined from both triaxiality and notchfabrication perspectives. Afterwards, a methodology is presented to extract the micromechanical-basedductile damage parameters from the load-displacement curve of notched SPT samples...

  18. 浅析Sandwich 教学法

    Institute of Scientific and Technical Information of China (English)

    田志逢

    2012-01-01

    为了真正实现学生为主体教师为主导的教学模式,我们把Sandwich 教学法引入课堂教学中.从教学内容的选取、课堂的设计、问题的设置、学生的分组、教师的总结等各个环节精心的安排,使得学生积极参与课堂,把课堂真正的交还给学生,从而积极有效的提高了学生学习的兴趣、动力,大幅度提高了教学效果.

  19. Bilateral sandwiched scapulae: A rare presentation of hereditary multiple exostoses.

    Science.gov (United States)

    Mozaffarian, Kamran; Farahani, Mohammad Javad; Vosoughi, Amir Reza

    2016-01-01

    Hereditary multiple exostoses, an autosomal dominant condition, is a common benign tumor which is characterized by the development of multiple osteochondromas. Bilateral dorsal and ventral involvement of scapulae is extremely rare without any reported case in the literature. An 18-year-old girl was referred because of bilateral prominent scapulae and left-sided pain on shoulder girdle motion especially at more than 90° abduction and forward flexion. Radiograph evaluation showed multiple exostoses on ventral and dorsal surfaces of body of both scapulae; hence simple excision of the lesion was impossible. The patient was symptom-free about 18 months after partial scapulectomy of left side. Partial scapulectomy seems to be an effective treatment for the sandwiched scapula between dorsal and ventral benign tumors.

  20. Smearing of chaos in sandwich pp-waves

    CERN Document Server

    Podolsky, J

    1999-01-01

    Recent results demonstrating the chaotic behavior of geodesics in non-homogeneous vacuum pp-wave solutions are generalized. Here we concentrate on motion in non-homogeneous sandwich pp-waves and show that chaos smears as the duration of these gravitational waves is reduced. As the number of radial bounces of any geodesic decreases, the outcome channels to infinity become fuzzy, and thus the fractal structure of the initial conditions characterizing chaos is cut at lower and lower levels. In the limit of impulsive waves, the motion is fully non-chaotic. This is proved by presenting the geodesics in a simple explicit form which permits a physical interpretation, and demonstrates the focusing effect. It is shown that a circle of test particles is deformed by the impulse into a family of closed hypotrochoidal curves in the transversal plane. These are deformed in the longitudinal direction in such a way that a specific closed caustic surface is formed.

  1. Analytical modeling of sandwich beam for piezoelectric bender elements

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Piezoelectric bender elements are widely used as electromechanical sensors and actuators. An analytical sandwich beam model for piezoelectric bender elements was developed based on the first-order shear deformation theory (FSDT), which assumes a single rotation angle for the whole cross-section and a quadratic distribution function for coupled electric potential in piezoelectric layers, and corrects the effect of transverse shear strain on the electric displacement integration. Free vibration analysis of simplysupported bender elements was carried out and the numerical results showed that, solutions of the present model for various thickness-to-length ratios are compared well with the exact two-dimensional solutions, which presents an efficient and accurate model for analyzing dynamic electromechanical responses of bender elements.

  2. Electrowetting-driven oscillating drops sandwiched between two substrates.

    Science.gov (United States)

    Mampallil, Dileep; Eral, H Burak; Staicu, Adrian; Mugele, Frieder; van den Ende, Dirk

    2013-11-01

    Drops sandwiched between two substrates are often found in lab-on-chip devices based on digital microfluidics. We excite azimuthal oscillations of such drops by periodically modulating the contact line via ac electrowetting. By tuning the frequency of the applied voltage, several shape modes can be selected one by one. The frequency of the oscillations is half the frequency of the contact angle modulation by electrowetting, indicating a parametric excitation. The drop response to sinusoidal driving deviates substantially from sinusoidal behavior in a "stop and go" fashion. Although our simple theoretical model describes the observed behavior qualitatively, the resonances appear at lower frequencies than expected. Moreover, the oscillations produce a nonperiodic fluid transport within the drop with a typical velocity of 1 mm/s. In digital microfluidic devices, where the typical drop size is less than 1 mm, this flow can result in very fast mixing on the spot.

  3. FMR studies of single permalloy layers sandwiched by Au

    Energy Technology Data Exchange (ETDEWEB)

    Hurdequint, H. [Laboratoire de Physique des Solides, UMR 8502, Universite Paris-Sud, 91405 ORSAY Cedex (France)]. E-mail: hurdequint@lps.u-psud.fr

    2007-03-15

    Results of FMR studies performed at X-band on two series of thin permalloy (Py) layers sandwiched by Au are reported and analyzed. These two series are characterized by an Au layer thickness of 12 and 6 nm, respectively. The FMR results are compared to the ones obtained for a series of (Py/Al{sub 2}O{sub 3}) control films. A strong interfacial increase of the intrinsic damping is revealed. The spin-orbit perpendicular anisotropy field is also dominated by the metallic interface contribution. Remarkable phenomena evidenced in the angular variation of the FMR spectrum may be well understood in terms of the theoretical description we have developed of the observable signal in a bimetallic (ferro/normal) film.

  4. Electrowetting-driven oscillating drops sandwiched between two substrates

    Science.gov (United States)

    Mampallil, Dileep; Burak Eral, H.; Staicu, Adrian; Mugele, Frieder; van den Ende, Dirk

    2013-11-01

    Drops sandwiched between two substrates are often found in lab-on-chip devices based on digital microfluidics. We excite azimuthal oscillations of such drops by periodically modulating the contact line via ac electrowetting. By tuning the frequency of the applied voltage, several shape modes can be selected one by one. The frequency of the oscillations is half the frequency of the contact angle modulation by electrowetting, indicating a parametric excitation. The drop response to sinusoidal driving deviates substantially from sinusoidal behavior in a “stop and go” fashion. Although our simple theoretical model describes the observed behavior qualitatively, the resonances appear at lower frequencies than expected. Moreover, the oscillations produce a nonperiodic fluid transport within the drop with a typical velocity of 1 mm/s. In digital microfluidic devices, where the typical drop size is less than 1 mm, this flow can result in very fast mixing on the spot.

  5. Mechanical properties and experimental researches of new CSIPs sandwich panels

    Directory of Open Access Journals (Sweden)

    Du Wenfeng

    2017-01-01

    Full Text Available The advantages of glass fiber reinforced composites (FRP and SIPs (structural insulated panels are combined, and a new type of sandwich panel called composite structural insulated panels (CSIPs is proposed. Through the adhesive bonding, CSIPs are made of FRP as face sheets and expanded polyethylene foam (EPS as a core. To master the mechanical characteristics of CSIPs, firstly, adopting the large deflection theory of Reissener in this paper derived the calculation formula of displacement and the stability critical load of CSIPs. Then, ANSYS software was used to carry on the analysis of finite element simulation. Finally, a testing piece of CSIP with length 1000mm and breath 1000mm was made and a test was done. The results show that the theoretical analysis results, finite element simulation results and test results are basically coincide. So the calculating formula of deformation and bearing capacity of CSIPs are correct. And CSIPs have the outstanding advantages of light weight and high strength.

  6. Applications of thin-film sandwich crystallization platforms.

    Science.gov (United States)

    Axford, Danny; Aller, Pierre; Sanchez-Weatherby, Juan; Sandy, James

    2016-04-01

    Examples are shown of protein crystallization in, and data collection from, solutions sandwiched between thin polymer films using vapour-diffusion and batch methods. The crystallization platform is optimal for both visualization and in situ data collection, with the need for traditional harvesting being eliminated. In wells constructed from the thinnest plastic and with a minimum of aqueous liquid, flash-cooling to 100 K is possible without significant ice formation and without any degradation in crystal quality. The approach is simple; it utilizes low-cost consumables but yields high-quality data with minimal sample intervention and, with the very low levels of background X-ray scatter that are observed, is optimal for microcrystals.

  7. Prediction of the ballistic limit of an aluminium sandwich panel

    Science.gov (United States)

    Campbell, J.; De Vuyst, T.; Vignjevic, R.; Hughes, K.

    2016-08-01

    This paper presents research on modelling the impact of a 150g projectile on a 35mm thick aluminium sandwich panel. The objective of the work is a predictive modelling capability for the ballistic limit of the panel. A predictive modelling capability supports the design of capture and deorbit missions for large items of space debris such as satellites and rocket upper stages. A detailed explicit finite element model was built using the LSDYNA software and results were compared with experimental data for the projectile exit velocity to establish key parameters. The primary parameters influencing the model behaviour were the strength and failure of the aluminium face sheets and the friction between projectile and panel. The model results showed good agreement with experimental results for ogive nose projectiles, but overestimated the exit velocity for flat nose projectiles.

  8. Immunometric Antibody Sandwich Enzyme-Linked Immunosorbent Assay.

    Science.gov (United States)

    Kohl, Thomas O; Ascoli, Carl A

    2017-06-01

    The antibody sandwich enzyme-linked immunosorbent assay (ELISA) is the most commonly used assay for rapid and accurate detection of antigens. It displays greater sensitivity compared with the indirect ELISA and can be used to determine absolute antigen concentrations in unknown samples provided purified antigen standards are available, although it requires the use of two different antibodies. Briefly, wells are coated with antigen-specific capture antibody then incubated with samples containing unknown antigen. Washing removes unbound antigen and exogenous sample protein before incubation with a second antigen-specific detection antibody, washing, and reincubation with a reporter-labeled tertiary antibody. After tertiary antibody is washed off, substrate is added and hydrolysis is measured spectrophotometrically. The signal intensity is directly proportional to the concentration of the antigen in the test sample. © 2017 Cold Spring Harbor Laboratory Press.

  9. On-Surface Synthesis of Sandwich Molecular Nanowires on Graphene.

    Science.gov (United States)

    Huttmann, Felix; Schleheck, Nicolas; Atodiresei, Nicolae; Michely, Thomas

    2017-07-26

    We demonstrate a new synthesis route for the growth of organometallic sandwich molecular nanowires, taking the example of Eu-cyclooctatetraene (EuCot), a predicted ferromagnetic semiconductor. We employ simultaneous exposure of Cot molecules and Eu vapor in ultrahigh vacuum to an inert substrate, such as graphene. Using a Cot excess under temperature conditions of a finite residence time of the molecule, the reactand diffusion confined to two dimensions results in a clean product of ultralong wires. In situ scanning tunneling microscopy reveals not only their molecular structure but also a rich and intriguing growth morphology. The new on-surface synthesis permits experimental access to a largely unexplored class of one-dimensional organometallic systems with potential for exciting electronic and magnetic properties.

  10. Morphology Analysis of Cu Film Fractures in Sandwiched Methylmethacrylate Plates

    Directory of Open Access Journals (Sweden)

    Cristiano Fidani

    2015-06-01

    Full Text Available Thin films of Cu were evaporated on solid plates of polymethylmethacrylate (PMMA. A polymerization process was made to realize sandwiched structure to protect the Cu films. Fracturing of the metal film surface was observed with several morphologies showing two different fracture systems. Surface film morphology was analysed in terms of the distribution area of the islands and contour fractal dimension. The island areas showed a maximum corresponding to 42 nm of the Cu thickness, it was also the threshold to observe the second fracture system. The fractures pattern resulted to be scale invariant with fractal dimensions between 1.55 and 1.7. The minimum fractal dimension also occurred at the film thickness corresponding to the maximum island area. The reported effects can be understood on the basis of different thermal expansion coefficients of the two materials and their thermally induced adhesion.DOI: http://dx.doi.org/10.5755/j01.ms.21.2.6518

  11. Equivariant Equipartitions: Ham Sandwich Theorems for Finite Subgroups of Spheres

    CERN Document Server

    Simon, Steven

    2011-01-01

    Equivariant "Ham Sandwich" Theorems are obtained for the finite subgroups of the unit spheres S^{d-1}, d=1,2,4. Given any F-valued mass distributions on F^n and any non-zero finite subgroup G of the unit sphere S^{d-1} in F= R, C, or H, it is shown that there exists a collection of fundamental G-regions partitioning F^n which "G-Equipartition" each of the n measures, as realized by the simultaneous vanishing of the "G-averages" of the regions' measures. Equipartition results for real measures follow, among them that any n signed mass distributions on R^{(p-1)n} can be equipartitioned by a single regular p-fan for any prime number p.

  12. Incidental prostate cancer in radical cystoprostatectomy specimens

    Institute of Scientific and Technical Information of China (English)

    Xiao-Dong Jin; Zhao-Dian Chen; Bo Wang; Song-Liang Cai; Xiao-Lin Yao; Bai-Ye Jin

    2008-01-01

    Aim: To investigate the rates of prostate cancer (Pca) in radical cystoprostatectomy (RCP) specimens for bladder cancer in mainland China. To determine the follow-up outcome of patients with two concurrent cancers and identify whether prostate-specific antigen (PSA) is a useful tool for the detection of Pca prior to surgery. Methods: From January 2002 to January 2007, 264 male patients with bladder cancer underwent RCP at our center. All patients underwent digital rectal examination (DRE) and B ultrasound. Serum PSA levels were tested in 168 patients. None of the patients had any evidence of Pca before RCP. Entire prostates were embedded and sectioned at 5 mm intervals. Results: Incidental Pca was observed in 37 of 264 (14.0%) RCP specimens. Of these, 12 (32.4%) were clinically significant according to an accepted definition. The PSA levels were not significantly different between patients with Pca and those without Pca, nor between patients with significant Pca and those with insignificant Pca. Thirty-four patients with incidental Pca were followed up. During a mean follow-up period of 26 months, two patients with PSA > 4 ng/mL underwent castration. None of the patients died of Pca. Conclusion: The incidence of Pca in RCP specimens in mainland China is lower than that in most developed countries. PSA cannot identify asymptomatic Pca prior to RCP. In line with published reports, incidental Pca does not impact the prognosis of bladder cancer patients undergoing RCP.

  13. Nondestructive and Strain Testing of Composite Sandwich Panels

    Science.gov (United States)

    Goyings, Ryan

    In April 2006, Sikorsky Aircraft received a contract from the United States Marine Corps (USMC) to develop a successor to their CH-53E heavy-lift helicopter. The new designation is the CH-53K "Super Stallion" and provides increased operating capabilities through the use of design revisions that incorporate extensive use of carbon fiber composites and composite sandwich panels. "The CH-53K will have five times the capability at half of the operational cost of the aircraft it's replacing. It will be the most capable helicopter ever produced. With more than twice the combat radius of the CH-53E, the CH-53K uses mature technology to deliver a fully shipboard compatible platform to meet current and future Marine Corps requirements". Upon introduction, it will be the largest rotary wing aircraft in the United States Department of Defense. The USMC will incorporate the CH-53K into the Joint Operations Concept of Full Spectrum Dominance and Sea Power 21 thereby enabling rapid, decisive operations and the early termination of conflict by projecting and sustaining forces to distant anti-access, area-denial environments. Even with an increased lift capability, the CH-53K is a slow moving, low flying helicopter susceptible to damage from small arms fire. There is no field level composite repair capability within any maintained documents published by the Department of Defense. Purdue University has developed a field level rapid repair technique capable of returning strength and integrity to damaged carbon composite structural components. The patch is made from carbon fiber weave that is applied using a field capable Vacuum Assisted Resin Transfer Molding (VARTM). This thesis seeks to validate, using nondestructive testing methods and strain monitoring, the manufacturing, damage, and repair process of composite sandwich panels representative of the CH-53K structural panels.

  14. Probabilistic Structural Evaluation of Uncertainties in Radiator Sandwich Panel Design

    Science.gov (United States)

    Kuguoglu, Latife; Ludwiczak, Damian

    2006-01-01

    The Jupiter Icy Moons Orbiter (JIMO) Space System is part of the NASA's Prometheus Program. As part of the JIMO engineering team at NASA Glenn Research Center, the structural design of the JIMO Heat Rejection Subsystem (HRS) is evaluated. An initial goal of this study was to perform sensitivity analyses to determine the relative importance of the input variables on the structural responses of the radiator panel. The desire was to let the sensitivity analysis information identify the important parameters. The probabilistic analysis methods illustrated here support this objective. The probabilistic structural performance evaluation of a HRS radiator sandwich panel was performed. The radiator panel structural performance was assessed in the presence of uncertainties in the loading, fabrication process variables, and material properties. The stress and displacement contours of the deterministic structural analysis at mean probability was performed and results presented. It is followed by a probabilistic evaluation to determine the effect of the primitive variables on the radiator panel structural performance. Based on uncertainties in material properties, structural geometry and loading, the results of the displacement and stress analysis are used as an input file for the probabilistic analysis of the panel. The sensitivity of the structural responses, such as maximum displacement and maximum tensile and compressive stresses of the facesheet in x and y directions and maximum VonMises stresses of the tube, to the loading and design variables is determined under the boundary condition where all edges of the radiator panel are pinned. Based on this study, design critical material and geometric parameters of the considered sandwich panel are identified.

  15. Experimental study of the mechanical behaviour of pin reinforced foam core sandwich materials under shear load

    Science.gov (United States)

    Dimassi, M. A.; Brauner, C.; Herrmann, A. S.

    2016-03-01

    Sandwich structures with a lightweight closed cell hard foam core have the potential to be used in primary structures of commercial aircrafts. Compared to honeycomb core sandwich, the closed cell foam core sandwich overcomes the issue of moisture take up and makes the manufacturing of low priced and highly integrated structures possible. However, lightweight foam core sandwich materials are prone to failure by localised external loads like low velocity impacts. Invisible cracks could grow in the foam core and threaten the integrity of the structure. In order to enhance the out-of-plane properties of foam core sandwich structures and to improve the damage tolerance (DT) dry fibre bundles are inserted in the foam core. The pins are infused with resin and co-cured with the dry fabric face sheets in an out-of-autoclave process. This study presents the results obtained from shear tests following DIN 53294-standard, on flat sandwich panels. All panels were manufactured with pin-reinforcement manufactured with the Tied Foam Core Technology (TFC) developed by Airbus. The effects of pin material (CFRP and GFRP) and pin volume fraction on the shear properties of the sandwich structure and the crack propagation were investigated and compared to a not pinned reference. It has been concluded that the pin volume fraction has a remarkable effect on the shear properties and damage tolerance of the observed structure. Increasing the pin volume fraction makes the effect of crack redirection more obvious and conserves the integrity of the structure after crack occurrence.

  16. Combined compressive and shear buckling analysis of hypersonic aircraft sandwich panels

    Science.gov (United States)

    Ko, William L.; Jackson, Raymond H.

    1992-01-01

    The combined-load (compression and shear) buckling equations were established for orthotropic sandwich panels by using the Rayleigh-Ritz method to minimize the panel total potential energy. The resulting combined-load buckling equations were used to generate buckling interaction curves for super-plastically-formed/diffusion-bonded titanium truss-core sandwich panels and titanium honeycomb-core sandwich panels having the same specific weight. The relative combined-load buckling strengths of these two types of sandwich panels are compared with consideration of their sandwich orientations. For square and nearly square panels of both types, the combined load always induces symmetric buckling. As the panel aspect ratios increase, antisymmetric buckling will show up when the loading is shear-dominated combined loading. The square panel (either type) has the highest combined buckling strength, but the combined load buckling strength drops sharply as the panel aspect ratio increases. For square panels, the truss-core sandwich panel has higher compression-dominated load buckling strength. However, for shear dominated loading, the square honeycomb-core sandwich panel has higher shear-dominated combined load buckling strength.

  17. Combined compressive and shear buckling analysis of hypersonic aircraft structural sandwich panels

    Science.gov (United States)

    Ko, William L.; Jackson, Raymond H.

    1991-01-01

    The combined-load (compression and shear) buckling equations were established for orthotropic sandwich panels by using the Rayleigh-Ritz method to minimize the panel total potential energy. The resulting combined-load buckling equations were used to generate buckling interaction curves for super-plastically-formed/diffusion-bonded titanium truss-core sandwich panels and titanium honeycomb-core sandwich panels having the same specific weight. The relative combined-load buckling strengths of these two types of sandwich panels are compared with consideration of their sandwich orientations. For square and nearly square panels of both types, the combined load always induces symmetric buckling. As the panel aspect ratios increase, antisymmetric buckling will show up when the loading is shear-dominated combined loading. The square panel (either type) has the highest combined buckling strength, but the combined load buckling strength drops sharply as the panel aspect ratio increases. For square panels, the truss-core sandwich panel has higher compression-dominated combined load buckling strength. However, for shear dominated loading, the square honeycomb-core sandwich panel has higher shear-dominated combined load buckling strength.

  18. EFFECT OF DIVIDED CORE ON THE BENDING PERFORMANCES OF TEXTILE REINFORCED FOAM CORE SANDWICH COMPOSITES

    Directory of Open Access Journals (Sweden)

    ALPYILDIZ Tuba

    2016-05-01

    Full Text Available Sandwich composites are generally used in marine applications, wind turbines, space and aircraft vehicles due to their high bending rigidities in addition to their lighter weights. The objective of this study is to investigate the effect of divided foam core and interlayer sheet of glass fabric on the bending performances of sandwich composites which are manufactured with glass fabrics as the facesheets/interlayer sheets and PVC foam as the core material. Sandwich composites with single and divided core are manufactured and compared in terms of flexural behavious via three point bending tests. It is found that the bending performance is enhanced with the use of divided core and using divided core does not affect the behaviour of the sandwich composite against bending deformations. In the case of the plain core sandwich composite, dividing the core is advised for certain applications rather than perforating the core to increase the bending stiffness and strength of the textile reinforced sandwich composites because it is possible to purchase core with any thickness and there is no need for additional process such as perforation. The proposed application could enhance the bending performances without altering the weight and cost of the sandwich composites, which are preferred due to their higher bending rigidities in relation to their lighter weights.

  19. 42 CFR 493.1232 - Standard: Specimen identification and integrity.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 5 2010-10-01 2010-10-01 false Standard: Specimen identification and integrity... Nonwaived Testing General Laboratory Systems § 493.1232 Standard: Specimen identification and integrity. The... optimum integrity of a patient's specimen from the time of collection or receipt of the specimen through...

  20. Specimen loading list for the varying temperature experiment

    Energy Technology Data Exchange (ETDEWEB)

    Qualls, A.L.; Sitterson, R.G. [Oak Ridge National Lab., TN (United States)

    1998-09-01

    The varying temperature experiment HFIR-RB-13J has been assembled and inserted in the reactor. Approximately 5300 specimens were cleaned, inspected, matched, and loaded into four specimen holders. A listing of each specimen loaded into the steady temperature holder, its position in the capsule, and the identification of the corresponding specimen loaded into the varying temperature holder is presented in this report.

  1. HMSRP Hawaiian Monk Seal Specimen Data (includes physical specimens, collection information, status, storage locations, and laboratory results associated with individual specimens)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set includes physical specimens, paper logs and Freezerworks database of all logged information on specimens collected from Hawaiian monk seals since 1975....

  2. Sandwich Structure-like Meshes Fabricated via Electrospinning for Controllable Release of Zoledronic Acid

    Institute of Scientific and Technical Information of China (English)

    LU Jian; LIU Jian-guo; SONG Xiao-feng; CHEN Xue-si; WU Xiao-dong

    2011-01-01

    Novel sandwich structure-like nanofiber multilayered meshes were fabricated via electrospinning. The purpose of the present work was to control zoledronic acid release via the novel structure of sandwich structure-like meshes. The in vitro release experiments reveal that the drug release speed and initial burst release were controllable by adjusting the thicknesses of electrospun barrier mesh and drug-loaded mesh. Compared with those of other drug delivery systems, the main advantages of the sandwich structure-like fiber meshes are facile preparation conditions and the generality for hydrophobic and hydrophilic pharmaceuticals.

  3. Modelling of Debond and Crack Propagation in Sandwich Structures Using Fracture and Damage Mechanics

    DEFF Research Database (Denmark)

    Berggreen, C.; Simonsen, Bo Cerup; Toernqvist, Rikard

    2003-01-01

    Skin-core de-bonding or core crack propagation will often be dominating mechanisms in the collapse modes of sandwich structures. This paper presents two different methods for prediction of crack propagation in a sandwich structure: a fracture mechanics approach, where a new mode-mix method...... is presented, and a local damage mechanics approach. The paper presents a real-life application example, where the superstructure in a vessel pulls the skin off the sandwich deck. The calculations show almost unstable crack growth initially followed by a stabilization, and a nearly linear relation between...

  4. Design Considerations for Thermally Insulating Structural Sandwich Panels for Hypersonic Vehicles

    Science.gov (United States)

    Blosser, Max L.

    2016-01-01

    Simplified thermal/structural sizing equations were derived for the in-plane loading of a thermally insulating structural sandwich panel. Equations were developed for the strain in the inner and outer face sheets of a sandwich subjected to uniaxial mechanical loads and differences in face sheet temperatures. Simple equations describing situations with no viable solution were developed. Key design parameters, material properties, and design principles are identified. A numerical example illustrates using the equations for a preliminary feasibility assessment of various material combinations and an initial sizing for minimum mass of a sandwich panel.

  5. The pleural sandwich sign in two cases of primary pleural lymphoma

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yoo Kyung; Lee, Myung Jae; Ryu, Yon Ju; Cho, Min Sun [School of Medicine, Ewha Womans University, Seoul (Korea, Republic of)

    2015-02-15

    The sandwich sign is used to describe mesenteric lymphoma in which mesenteric vessels and fat are enveloped by enlarged mesenteric lymph nodes. We present two cases of primary pleural lymphoma demonstrating the 'pleural sandwich sign'. Contrast-enhanced computed tomography showed conglomerated parietal pleural and extrapleural masses encasing the intercostal arteries. Histopathological examinations confirmed low grade marginal zone B-cell lymphoma in an 80-year-old man and diffuse large B-cell lymphoma in a 68-year-old man. The pleural sandwich sign may suggest the diagnosis of primary pleural lymphoma.

  6. Elastic constants for superplastically formed/diffusion-bonded corrugated sandwich core

    Science.gov (United States)

    Ko, W. L.

    1980-01-01

    Formulas and associated graphs for evaluating the effective elastic constants for a superplastically formed/diffusion bonded (SPF/DB) corrugated sandwich core, are presented. A comparison of structural stiffnesses of the sandwich core and a honeycomb core under conditions of equal sandwich core density was made. The stiffness in the thickness direction of the optimum SPF/DB corrugated core (that is, triangular truss core) is lower than that of the honeycomb core, and that the former has higher transverse shear stiffness than the latter.

  7. Fatigue failure of sandwich beams with face sheet wrinkle defects

    DEFF Research Database (Denmark)

    Leong, Martin Klitgaard; Hvejsel, C.F.; Thomsen, Ole Thybo

    2012-01-01

    and application of the Northwestern University failure criteria. The presence of a wrinkle defect reduced the fatigue life by approximately 66%, compared to that of an unnotched reference laminate. Furthermore, the results from the fatigue tests revealed that the design limit was initially overestimated......, as the specimens loaded close to the predicted design limit typically failed before reaching the target life, or reached test run-out with visible face sheet damage indicating imminent final failure in the worst case. It was found that specimens would reach target life with no visible or otherwise detectable...

  8. Wildlife specimen collection, preservation, and shipment

    Science.gov (United States)

    White, C. LeAnn; Dusek, Robert J.; Franson, J. Christian; Friend, Milton; Gibbs, Samantha E.J.; Wild, Margaret A.

    2015-01-01

    Specimens are used to provide supporting information leading to the determination of the cause of disease or death in wildlife and for disease monitoring or surveillance. Commonly used specimens for wildlife disease investigations include intact carcasses, tissues from carcasses, euthanized or moribund animals, parasites, ingested food, feces, or environmental samples. Samples from live animals or the environment (e.g., contaminated feed) in the same vicinity as a mortality event also may be helpful. The type of specimen collected is determined by availability of samples and biological objectives. Multiple fresh, intact carcasses from affected species are the most useful in establishing a cause for a mortality event. Submission of entire carcasses allows observation of gross lesions and abnormalities, as well as disease testing of multiple tissues. Samples from live animals may be more appropriate when sick animals cannot be euthanized (e.g., threatened or endangered species) or for research and monitoring projects examining disease or agents circulating in apparently healthy animals or those not exhibiting clinical signs. Samples from live animals may include collections of blood, hair, feathers, feces, or ectoparasites, or samples obtained by swabbing lesions or orifices. Photographs and videos are useful additions for recording field and clinical signs and conveying conditions at the site. Collection of environmental samples (e.g., feces, water, feed, or soil) may be appropriate when animals cannot be captured for sampling or the disease agent may persist in the environment. If lethal collection is considered necessary, biologists should refer to the policies, procedures, and permit requirements of their institution/facility and the agency responsible for species management (U.S. Fish and Wildlife Service or State natural resource agency) prior to use in the field. If threatened or endangered species are found dead, or there is evidence of illegal take, field

  9. Histological evaluation of 400 cholecystectomy specimens

    Directory of Open Access Journals (Sweden)

    H Kumar

    2015-09-01

    Full Text Available Background: A majority of gallbladder specimens show changes associated with chronic cholecystitis; however few harbour a highly lethal carcinoma. This study was conducted to review the significant histopathological findings encountered in gallbladder specimens received in our laboratory.Materials and Methods: Four hundred cholecystectomy specimens were studied over a period of five years (May, 2002 to April, 2007 received at department of pathology, Kasturba Medical College, Mangalore, India. Results: Gallstones and associated diseases were more common in women in the 4th to 5th decade as compared to men with M: F ratio of 1:1.33. Maximum number of patients (28.25% being 41 to 50 years old. Histopathologically, the most common diagnosis was chronic cholecystitis (66.75%, followed by chronic active cholecystitis (20.25%, acute cholecystitis (6%, gangrenous cholecystitis (2.25%,xanthogranulomatous cholecystitis (0.50%, empyema (1%, mucocele (0.25%, choledochal cyst (0.25%, adenocarcinoma gallbladder (1.25% and  normal  gallbladders (1%.Conclusion: All lesions were found more frequently in women except chronic active cholecystitis. Gallstones were present in (80.25% cases, and significantly associated with various lesions (P value 0.009. Pigment stones were most common, followed by cholesterol stones and mixed stones. Adequate  sectioning  is  mandatory  in  all  cases  to  assess  epithelial changes arising from cholelithiasis and chronic cholecystitis as it has been known to progress to malignancy in some cases.

  10. Isolation of Klebsiella terrigena from clinical specimens.

    Science.gov (United States)

    Podschun, R; Ullmann, U

    1992-04-01

    In a three-year survey conducted from 1988 to 1990 Klebsiella isolates from human clinical specimens were subjected to additional tests to identify any Klebsiella terrigena strains. Ten strains of Klebsiella terrigena (0.4%) were found among 2355 indole-negative Klebsiella isolates. Most of the isolates were recovered from the respiratory tract. In the API20EC system almost exclusively biotypes no. 1777771 and 1777671 were observed. Serotyping revealed capsule types K2, K5 and K18 in two strains each. In antibiotic susceptibility tests the strains were shown to be comparable in sensitivity to Klebsiella pneumoniae.

  11. Fabrication and Characterization of Li-6 Sandwich Detector

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Kiwhan [Future and Challenge Technology Co., Yongin (Korea, Republic of); Iliev, Metodi; Ianakiev, Kiril; Swinhoe, Martyn [Los Alamos National Laboratory, New Mexico (United States)

    2014-10-15

    Lithium-6 has been used as a radiation detector material for its ability to react with thermal neutrons, producing alphas and tritons as the primary charged particles during the neutron conversion reaction. Lithium-6 has a thermal neutron cross section of 940 barns, producing a 2.05 MeV alpha particle and a 2.73 MeV triton in a back to back symmetry to conserve energy and momentum, if the incident thermal neutron has low energy. The most widely recognized thermal neutron conversion reaction involves He-3. A He-3 atom has a thermal neutron cross section of 5330 barns, but its resulting particles have total 0.764 MeV to share between a proton and triton. The use of He-3 gas is not limited to homeland security and international safe-guards programs; the high energy physics and medical communities all benefit from the unique capabilities of He-3. As fission neutrons enter the sandwich medium consisting of light guides, plastic scintillator, and lithium-6 foil, they lose energy in the volume. Some neutrons are reduced to thermal energy range and interact with lithium-6 atoms, producing a triton and an alpha particle during the reaction. The primary charged particles then impart their energies in the plastic scintillator film, producing photons. The photons then travels toward the ends of the light guide strips and get collected by the PMTs. Initially, the lithium-6 metal was in storage for many years at the Y-12 National Security Complex, Oak Ridge, Tenneessee, and the metal piece needed reprocessing as shown in Fig. 3. The piece was transported to a lithium battery production facility which had the capability to reprocess lithium ingots. After the metal was reprocessed, it was purified to 95% enrichment and regained sheen (Fig. 4). The foil was extruded as 50-micron, 5 cm-wide strips as shown in inset of Fig. 4. The rolls were stored in an airtight pouch which was filled with dry argon and sealed in a metal container capable of withstanding long term storage as shown

  12. Twistable and bendable actuator: a CNT/polymer sandwich structure driven by thermal gradient.

    Science.gov (United States)

    Seo, Dong Kyun; Kang, Tae June; Kim, Dae Weon; Kim, Yong Hyup

    2012-02-24

    We demonstrate a novel configuration of an electrothermal actuator (ETA), which is based on a polydimethylsiloxane (PDMS) slab sandwiched by upper and lower active layers of CNT-PDMS composite. When only one active layer of a single sandwich structure ETA is heated and the other is not, there exists a thermal gradient in the direction of the slab thickness, resulting in bending motion toward the unheated side. Moreover, a dual sandwich structure ETA, consisting of two parallel assembled sandwich structures on the same body, has the unique ability to act with a twisting motion as the two ETAs bend in opposite directions. We expect the advent of the bendable and twistable actuator to break new ground in ETAs.

  13. Novel sandwich structure adsorptive membranes for removal of 4-nitrotoluene from water

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Yuexin [College of Chemistry, Beijing Normal University, Beijing 100875 (China); School of Pharmacy, North China University of Science and Technology, Tangshan 063000 (China); Jia, Zhiqian, E-mail: zhqjia@bnu.edu.cn [College of Chemistry, Beijing Normal University, Beijing 100875 (China)

    2016-11-05

    Highlights: • Novel sandwich PES-SPES/PS-PDVB/PTFE adsorptive membranes were prepared. • The removal efficiency for 4-nitrotoluene is greater than 95% after five recycles. • The membrane showed higher adsorption capacity than that of mixed matrix membrane. - Abstract: Novel sandwich PES-SPES/PS-PDVB/PTFE adsorptive membranes were prepared by a filtration/immersion precipitation method and employed for the removal of 4-nitrotoluene from water. The static adsorption thermodynamics, kinetics, dynamic adsorption/desorption and membrane reusability were investigated. The results showed that the Freundlich model describes the adsorption isotherm satisfactorily. With increased PS-PDVB content, the maximum static adsorption capacity, partition coefficient, apparent adsorption rate constant, and dynamic adsorption capacity all significantly increased. The sandwich membranes showed much higher removal efficiency and adsorption capacity than those of mixed matrix membranes. With respect to dynamics adsorption/desorption, the sandwich membranes exhibited excellent reusability, with a removal efficiency greater than 95% even after five recycles.

  14. A variable transverse stiffness sandwich structure using fluidic flexible matrix composites (F2MC)

    Science.gov (United States)

    Li, Suyi; Lotfi, Amir; Shan, Ying; Wang, K. W.; Rahn, Christopher D.; Bakis, Charles E.

    2008-03-01

    Presented in this paper is the development of a novel honeycomb sandwich panel with variable transverse stiffness. In this structure, the traditional sandwich face sheets are replaced by the fluidic flexible matrix composite (F2MC) tube layers developed in recent studies. The F2MC layers, combined with the anisotropic honeycomb core material properties, provide a new sandwich structure with variable stiffness properties for transverse loading. In this research, an analytical model is derived based on Lekhitskii's anisotropic pressurized tube solution and Timoshenko beam theory. Experimental investigations are also conducted to verify the analytical findings. A segmented multiple-F2MC-tube configuration is synthesized to increase the variable stiffness range. The analysis shows that the new honeycomb sandwich structure using F2MC tubes of 10 segments can provide a high/low transverse stiffness ratio of 60. Segmentation and stiffness control can be realized by an embedded valve network, granting a fast response time.

  15. Blast-Resistant Improvement of Sandwich Armor Structure with Aluminum Foam Composite

    Directory of Open Access Journals (Sweden)

    Shu Yang

    2013-01-01

    Full Text Available Sandwich armor structures with aluminum foam can be utilized to protect a military vehicle from harmful blast load such as a landmine explosion. In this paper, a system-level dynamic finite element model is developed to simulate the blast event and to evaluate the blast-resistant performance of the sandwich armor structure. It is found that a sandwich armor structure with only aluminum foam is capable of mitigating crew injuries under a moderate blast load. However, a severe blast load causes force enhancement and results in much worse crew injury. An isolating layer between the aluminum foam and the vehicle floor is introduced to remediate this drawback. The results show that the blast-resistant capability of the innovative sandwich armor structure with the isolating layer increases remarkably.

  16. Theoretical Calculation and Analysis of Slip and Deformation for Concrete Sandwich Panels

    Institute of Scientific and Technical Information of China (English)

    LI Yanbo; ZHANG Shaohua; XIA Baoyang

    2007-01-01

    Slip and deformation of concrete sandwich panels under uniformly distributed loads is concerned. The effect of slip on the deformation of concrete sandwich panels are studied, and the analytical expressions of slip and deformation for concrete sandwich panels is obtained. These formulae can describe the slip distribution and account for its effect on deformation. In order to restrict the bound of formula, the formula of crack moment is obtained. The results of theoretical calculation are compared with those of tests and finite element methods. The comparison shows that the results of theoretical calculation are in accord with those of tests and finite element methods. So the theoretical calculation can be used to calculate slip and deformation of concrete sandwich panels in practical projects.

  17. Analytical study of sandwich structures using Euler-Bernoulli beam equation

    Science.gov (United States)

    Xue, Hui; Khawaja, H.

    2017-01-01

    This paper presents an analytical study of sandwich structures. In this study, the Euler-Bernoulli beam equation is solved analytically for a four-point bending problem. Appropriate initial and boundary conditions are specified to enclose the problem. In addition, the balance coefficient is calculated and the Rule of Mixtures is applied. The focus of this study is to determine the effective material properties and geometric features such as the moment of inertia of a sandwich beam. The effective parameters help in the development of a generic analytical correlation for complex sandwich structures from the perspective of four-point bending calculations. The main outcomes of these analytical calculations are the lateral displacements and longitudinal stresses for each particular material in the sandwich structure.

  18. Templating odd numbered magnetic rings: oxovanadium heptagons sandwiched by beta-cyclodextrins.

    Science.gov (United States)

    Hoshino, Norihisa; Nakano, Motohiro; Nojiri, Hiroyuki; Wernsdorfer, Wolfgang; Oshio, Hiroki

    2009-10-28

    The oxovanadium heptagons sandwiched by beta-cyclodextrins showed stepped magnetization curves, which were characteristic of level crossings of spin sublevels. Doubly degenerate ground Kramers' doublets split into two spin states, and the splitting energy gaps depend upon ring distortions.

  19. Vibroacoustic optimization of anti-tetrachiral and auxetic hexagonal sandwich panels with gradient geometry

    Science.gov (United States)

    Ranjbar, Mostafa; Boldrin, Luca; Scarpa, Fabrizio; Neild, Simon; Patsias, Sophoclis

    2016-05-01

    The work describes the vibroacoustic behavior of anti-tetrachiral and auxetic hexagonal gradient sandwich panels using homogenized finite element models to determine the mechanical properties of the auxetic structures, the natural frequencies and radiated sound power level of sandwich panels made by the auxetic cores. The mechanical properties and the vibroacoustic behavior of auxetic hexagonal sandwich panels are investigated as a benchmark. The radiated sound power level of the structure over the frequency range of 0-1000 Hz is minimized by modifying the core geometry of the gradient auxetic sandwich panels. Several excitation cases are considered. First-order and random optimization methods are used for the minimization of radiated sound power level of the structures. The results of this study present significant insights into the design of auxetic structures with respect to their vibroacoustical properties.

  20. Experimental and Theoretical Deflections of Hybrid Composite Sandwich Panel under Four-point Bending Load

    Directory of Open Access Journals (Sweden)

    Jauhar Fajrin

    2017-03-01

    Full Text Available This paper presents a comparison of theoretical and experimental deflection of a hybrid sandwich panel under four-point bending load. The paper initially presents few basic equations developed under three-point load, followed by development of model under four-point bending load and a comparative analysis between theoretical and experimental results. It was found that the proposed model for predicting the deflection of hybrid sandwich panels provided fair agreement with the experimental values. Most of the sandwich panels showed theoretical deflection values higher than the experimental values, which is desirable in the design. It was also noticed that the introduction of intermediate layer does not contribute much to reduce the deflection of sandwich panel as the main contributor for the total deflection was the shear deformation of the core that mostly determined by the geometric of the samples and the thickness of the core.

  1. Flutter Characteristic Study of Composite Sandwich Panel with Functionally Graded Foam Core

    Directory of Open Access Journals (Sweden)

    Peng Jin

    2016-01-01

    Full Text Available This paper attempts to investigate the flutter characteristic of sandwich panel composed of laminated facesheets and a functionally graded foam core. The macroscopic properties of the foam core change continuously along this direction parallel to the facesheet lamina. The model used in the study is a simple sandwich panel-wing clamped at the root, with three simple types of grading strategies for FGM core: (1 linear grading strategy in the chord-wise direction, (2 linear grading strategy in the span-wise direction, and (3 bilinear grading of properties of foam core across the panel. The results show that use of FGM core has the potential to increase the flutter speed of the sandwich panel. Finally, a minimum weight design of composite sandwich panel with lamination parameters of facesheet and density distribution of foam core as design variables is conducted using particle swarm optimization (PSO.

  2. Two dimensional dynamic analysis of sandwich plates with gradient foam cores

    Energy Technology Data Exchange (ETDEWEB)

    Mu, Lin; Xiao, Deng Bao; Zhao, Guiping [State Key Laboratory for Mechanical structure Strength and Vibration, School of AerospaceXi' an Jiaotong University, Xi' an (China); Cho, Chong Du [Dept. of Mechanical Engineering, Inha University, Inchon (Korea, Republic of)

    2016-09-15

    Present investigation is concerned about dynamic response of composite sandwich plates with the functionally gradient foam cores under time-dependent impulse. The analysis is based on a model of the gradient sandwich plate, in which the face sheets and the core adopt the Kirchhoff theory and a [2, 1]-order theory, respectively. The material properties of the gradient foam core vary continuously along the thickness direction. The gradient plate model is validated with the finite element code ABAQUS®. And the results show that the proposed model can predict well the free vibration of composite sandwich plates with gradient foam cores. The influences of gradient foam cores on the natural frequency, deflection and energy absorbing of the sandwich plates are also investigated.

  3. An Investigation on Low Velocity Impact Response of Multilayer Sandwich Composite Structures

    Directory of Open Access Journals (Sweden)

    S. Jedari Salami

    2013-01-01

    Full Text Available The effects of adding an extra layer within a sandwich panel and two different core types in top and bottom cores on low velocity impact loadings are studied experimentally in this paper. The panel includes polymer composite laminated sheets for faces and the internal laminated sheet called extra layer sheet, and two types of crushable foams are selected as the core material. Low velocity impact tests were carried out by drop hammer testing machine to the clamped multilayer sandwich panels with expanded polypropylene (EPP and polyurethane rigid (PUR in the top and bottom cores. Local displacement of the top core, contact force and deflection of the sandwich panel were obtained for different locations of the internal sheet; meanwhile the EPP and PUR were used in the top and bottom cores alternatively. It was found that the core material type has made significant role in improving the sandwich panel’s behavior compared with the effect of extra layer location.

  4. Stress Distribution on Sandwich Structure with Triangular Grid Cores Suffered from Bending Load

    Directory of Open Access Journals (Sweden)

    Cui Xu

    2015-01-01

    Full Text Available Triangular grid reinforced by carbon fiber/epoxy (CF/EP was designed and manufactured. The sandwich structure was prepared by gluing the core and composite skins. The mechanical properties of the sandwich structure were investigated by the finite element analysis (FEA and three-point bending methods. The calculated bending stiffness and core shear stress were compared to the characteristics of a honeycomb sandwich structure. The results indicated that the triangular core ultimately failed under a bending load of 11000 N; the principal stress concentration was located at the loading region; and the cracks occurred on the interface top skin and triangular core. In addition, the ultimate stress bearing of the sandwich structure was 8828 N. The experimental results showed that the carbon fiber reinforced triangular grid was much stiffer and stronger than the honeycomb structure.

  5. Investigation of out of plane compressive strength of 3D printed sandwich composites

    Science.gov (United States)

    Dikshit, V.; Yap, Y. L.; Goh, G. D.; Yang, H.; Lim, J. C.; Qi, X.; Yeong, W. Y.; Wei, J.

    2016-07-01

    In this study, the 3D printing technique was utilized to manufacture the sandwich composites. Composite filament fabrication based 3D printer was used to print the face-sheet, and inkjet 3D printer was used to print the sandwich core structure. This work aims to study the compressive failure of the sandwich structure manufactured by using these two manufacturing techniques. Two different types of core structures were investigated with the same type of face-sheet configuration. The core structures were printed using photopolymer, while the face-sheet was made using nylon/glass. The out-of-plane compressive strength of the 3D printed sandwich composite structure has been examined in accordance with ASTM standards C365/C365-M and presented in this paper.

  6. Magnetic and Structural Properties in Co/Cu/Co Sandwiches with Ni and Cr Buffer Layers

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The magnetic and structural properties in Co/Cu/Co sandwiches with Ni and Cr buffer layers were investigated. It was found that the coercivity in Ni layer buffered samples decreases with increasing Ni layer thickness, while that in Cr layer buffered ones increases with increasing Cr layer thickness, leading to a large difference in field sensitivity of their giant magnetoresistance (GMR) properties. X-ray diffraction and high resolution transmission electron microscope images exhibited that there is a strong fcc (111) texture in the samples with Ni buffer layer. But there are only randomly oriented polycrystalline grains in Cr buffered sandwiches. According to atomic force microscope topography, the surface roughness of Cr buffered sandwiches is smaller than that of Ni buffered ones. It is demonstrated that buffer layer influences both magnetic and structural properties in Co/Cu/Co sandwiches as well as their GMR characteristics.

  7. Wave propagation and absorption of sandwich beams containing interior dissipative multi-resonators.

    Science.gov (United States)

    Chen, H; Li, X P; Chen, Y Y; Huang, G L

    2017-04-01

    In this study, a sandwich beam with periodic multiple dissipative resonators in the sandwich core material is investigated for broadband wave mitigation and/or absorption. An analytical approach based on the transfer matrix method and Bloch theorem is developed for both infinite and finite sandwich structures. Wave attenuation constants are theoretically obtained to examine the effects of various system parameters on the position, width and wave attenuation performance of the band gaps. The wave absorption coefficient of the sandwich beam is quantitatively studied to distinguish wave attenuation mechanisms caused by reflection and absorption. It is numerically demonstrated that a transient blast-induced elastic wave with broadband frequencies can be almost completely mitigated or absorbed at a subwavelength scale. The results of this study could be used for developing new multifunctional composite materials to suppress impact-induced and/or blast-induced elastic waves which may cause severe local damage to engineering structures.

  8. Sandwich-type theorems for a class of integral operators with special properties

    Directory of Open Access Journals (Sweden)

    Parisa Hariri

    2014-02-01

    Full Text Available In the present paper, we prove subordination, superordination and sandwich-type properties of a certain integral operators for univalent functions on open unit disc, moreover the special behavior of this class is investigated.

  9. Effects of Core Softness and Bimodularity of Fibreglass Layers on Flexural Stiffness of Polymer Sandwich Structures

    Directory of Open Access Journals (Sweden)

    Šuba Oldřich

    2017-01-01

    Full Text Available This paper deals with the study of the flexural stiffness of the sandwich structures based on fibreglass and polymeric foams. The influence of geometrical and material parameters on the resulting effective flexural stiffness of the sandwich structure is being studied experimentally, analytically and by using FEM models. The effective modulus of elasticity of the sandwich-structured element is being studied and its theoretical and model dependencies on the flexibility of the foam core and bimodularity of the fibreglass layers are being investigated. The achieved results are compared with the experimentally observed values. This study shows that it is necessary to pay special attention to the issue of flexural stiffness of the walls when designing sandwich shell products in order to prevent possible failures in the practical applications of these types of structures.

  10. Prediction of Thermal and Elastic Properties of Honeycomb Sandwich Plate for Analysis of Thermal Deformation

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Seok Min; Lee, Jang Il; Byun, Jae Ki; Choi, Young Don [Korea Univ., Seoul (Korea, Republic of)

    2014-04-15

    Thermal problems that are directly related to the lifetime of an electronic device are becoming increasingly important owing to the miniaturization of electronic devices. To solve thermal problems, it is essential to study thermal stability through thermal diffusion and insulation. A honeycomb sandwich plate has anisotropic thermal conductivity. To analyze the thermal deformation and temperature distribution of a system that employs a honeycomb sandwich plate, the thermal and elastic properties need to be determined. In this study, the thermal and elastic properties of a honeycomb sandwich plate, such as thermal conductivity, coefficient of thermal expansion, elastic modulus, Poisson's ratio, and shear modulus, are predicted. The properties of a honeycomb sandwich plate vary according to the hexagon size, thickness, and material properties.

  11. Mid term results of total hip arthroplasty using polyethylene-ceramic composite (Sandwich liner

    Directory of Open Access Journals (Sweden)

    Tao Wang

    2016-01-01

    Conclusions: Our experience with the ceramic-polyethylene sandwich liner acetabular component has been disappointing because of the high rate of fracture and osteolyis. We have discontinued the use of this device and recommend the same.

  12. Penetration of sandwich plates with hybrid-cores under oblique ballistic impact

    Directory of Open Access Journals (Sweden)

    Changye Ni

    2014-01-01

    Full Text Available The oblique penetration performance of lightweight hybrid-cored sandwich plates are investigated numerically. To compose the hybrid-core, ceramic prisms are inserted into pyramidal metal lattice trusses and fixed using epoxy resin. Three-dimensional finite element simulations are carried out for the hybridcored sandwich impacted at 15°, 30°, 45°, and 60° obliquity by a hemispherical projectile. The ballistic limit, the energy absorbed by the constituting elements, and the critical oblique angle are quantified. The physical mechanisms underlying the failure and the influence of fundamental system parameters are explored. The angle of obliquity is found to have significant influence on the ballistic trajectory and erosion of the projectile, thus it is important for the impact response and penetration resistance of the sandwich. For oblique angles equal to or larger than 45°, the projectile moves mainly horizontally and can not effectively penetrate across the sandwich.

  13. Detection of Penicillinase in Milk by Sandwich ELISA Based Polyclonal and Monoclonal Antibody.

    Science.gov (United States)

    Zhao, Yinli; Li, Guoxi

    2016-01-01

    A sandwich ELISA has been developed using polyclonal and monoclonal antibody for the determination of penicillinase in milk. For this purpose, specific polyclonal and monoclonal antibodies against penicillinase were generated and characterized. Using penicillinase standards prepared from 1-128 ng/mL, the method indicated that the detection limit of the sandwich ELISA, as measured in an ELISA plate reader, was as low as 0.86 ng/mL of penicillinase. For determine the accuracy, raw milk containing 2, 8, 32, and 64 ng/mL of penicillinase were tested by sandwich ELISA. Recoveries were from 93-97.5%, and the coefficient of variation [CV (%)] were from 5.55-8.38%. For interassay reproducibility, recoveries were from 89.5-95.1%, the coefficient of variation [CV (%)] were from 5.26-9.58%. This sandwich ELISA provides a useful screening method for quantitative detection of penicillinase in milk.

  14. Study on folds of monolayer sandwiched-in different thickness terranes

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The paper discussed the limitation of ‘Dominant wavelength theory’. The theoretical model and nonhomogeneous differential equation of fold and deformation of a monolayer sandwiched-in limited and different thickness terranes are proposed by using mechanics of elasticity. In addition, the ′Dominant wavelength theory’ is proved by the experimental folding in elastic materials. The folds of a monolayer sandwiched-in limited and different thickness terranes are studied inside and are explored in the field.

  15. The primitive matrices of sandwich semigroups of generalized circulant Boolean matrices

    Institute of Scientific and Technical Information of China (English)

    LIU Jian-ping; CHEN Jin-song

    2013-01-01

    Let Gn(C) be the sandwich semigroup of generalized circulant Boolean matrices with the sandwich matrix C and GC (Jn) the set of all primitive matrices in Gn(C). In this paper, some necessary and suffi cient conditions for A in the semigroup Gn(C) to be primitive are given. We also show that GC (Jn) is a subsemigroup of Gn(C).

  16. Geometrical parameters influence on behavior of the sandwich plates with corrugated core

    Directory of Open Access Journals (Sweden)

    Djoković Jelena M.

    2016-01-01

    Full Text Available The influence of geometric parameters on behavior and stiffness of sandwich plates with corrugated core is considered in this paper. The following parameters were analyzed: ratio of core sheet and facing sheet thickness and the ratio of the core’s pitch to the core’s depth, as well as the corrugation angle. It is shown that changes of these parameters can contribute to increase or decrease of the corrugated sandwich plate stiffness.

  17. Assessment of foam fracture in sandwich beams using thermoelastic stress analysis

    DEFF Research Database (Denmark)

    Dulieu-Barton, J.M.; Berggreen, Christian; Mettemberg, C.

    2009-01-01

    Thermoelastic Stress Analysis (TSA) has been well established for determining crack-tip parameters in metallic materials. This paper examines its ability to determine accurately the crack-tip parameters for PVC foam used in sandwich structures.......Thermoelastic Stress Analysis (TSA) has been well established for determining crack-tip parameters in metallic materials. This paper examines its ability to determine accurately the crack-tip parameters for PVC foam used in sandwich structures....

  18. Polyisocyanurate systems for insulating and sandwich elements; Polyisocyanurat-Systeme fuer Daemm- und Sandwichelemente

    Energy Technology Data Exchange (ETDEWEB)

    Malotki, P. von [Elastogran GmbH, Lemfoerde (Germany)

    2000-07-01

    PUR rigid foam plates are laminated with flexible Al films, paper or glass non-wovens, or may be processed into sandwich elements with metallic top-layers via coil-coating. Dependence of heat insulation efficiency, dimensional stability and fire behavior of the foam on chemical composition and the blowing agents is considered and compared with polyisocyanurate foams. Recipes for the production of PIR heat insulation elements and sandwich elements are given.

  19. Multiscale Modeling Methods for Analysis of Failure Modes in Foldcore Sandwich Panels

    Science.gov (United States)

    Sturm, R.; Schatrow, P.; Klett, Y.

    2015-12-01

    The paper presents an homogenised core model suitable for use in the analysis of fuselage sandwich panels with folded composite cores under combined loading conditions. Within a multiscale numerical design process a failure criterion was derived for describing the macroscopic behaviour of folded cores under combined loading using a detailed foldcore micromodel. The multiscale modelling method was validated by simulation of combined compression/bending failure of foldcore sandwich panels.

  20. EXPERIMENTAL ANALYSIS OF FLEXURAL STRENGTH ON GLASS FIBER SANDWICH COMPOSITE BY VARYING Z-PINS PITCHES

    OpenAIRE

    Pravin*, Jeyapratha

    2016-01-01

    This paper ambit to evaluate the flexural strength of glass fiber sandwich panels with varying z-pins pitches. Failure of sandwich panel are delamination and core shear, to minimize the crack propagation, pins are inserted in z-direction, by varying pitches through its thickness. During the insertion of pin, may cause the material some damage. Despite the damage, flexural property does not affected due interpolation of pins. Although the experiment were pull out with a phenomenal results of z...

  1. Mechanical behavior of a sandwich with corrugated GRP core: numerical modeling and experimental validation

    OpenAIRE

    Tumino, D; T. Ingrassia; V. Nigrelli; G. Pitarresi; V. Urso Miano

    2014-01-01

    In this work the mechanical behaviour of a core reinforced composite sandwich structure is studied. The sandwich employs a Glass Reinforced Polymer (GRP) orthotropic material for both the two external skins and the inner core web. In particular, the core is designed in order to cooperate with the GRP skins in membrane and flexural properties by means of the addition of a corrugated laminate into the foam core. An analytical model has been developed to replace a unit cell of this s...

  2. Analysis and Testing of a Tapered End Connection for Laser Welded Steel Sandwich Panels

    Science.gov (United States)

    2009-08-15

    1951, Elastic Constants for Corrugated Core Sandwich Plates. Technical Note 2289. National Aeronautics and Space Administration ( NASA ). 19. Lok...Assoc. Professor of Mechanical Engineering, University of Maine (Co-I) Grant No: N00014-05-1 -0735 ATS subcontract No: UM-591 Report No. C-2004-015...RPT-04 August 15,2009 20090925154 ABSTRACT This report summarize the analysis and cyclic testing of a laser welded steel sandwich panel end

  3. Structural performance of complex core systems for FRP-balsa composite sandwich bridge decks

    OpenAIRE

    Osei-Antwi, Michael

    2014-01-01

    Based on current fiber-reinforced polymer (FRP) composite construction principles, FRP decks fall into two categories: pultruded decks and sandwich decks. Sandwich decks comprise face sheets and either honeycombs or foams reinforced with internal FRP webs for shear resistance. The honeycomb structure and the webs cause debonding between the upper face sheets and the core due to the uneven support of the former. An alternative material that has high shear capacity and can provide uniform ...

  4. Numerical analysis of sandwich beam with corrugated core under three-point bending

    Energy Technology Data Exchange (ETDEWEB)

    Wittenbeck, Leszek [Poznan University of Technology, Institute of Mathematics Piotrowo Street No. 5, 60-965 Poznan (Poland); Grygorowicz, Magdalena; Paczos, Piotr [Poznan University of Technology, Institute of Applied Mechanics Jana Pawla IIStreet No. 24, 60-965 Poznan (Poland)

    2015-03-10

    The strength problem of sandwich beam with corrugated core under three-point bending is presented.The beam are made of steel and formed by three mutually orthogonal corrugated layers. The finite element analysis (FEA) of the sandwich beam is performed with the use of the FEM system - ABAQUS. The relationship between the applied load and deflection in three-point bending is considered.

  5. Influence of weld stiffness on buckling strength of laser-welded web-core sandwich plates

    OpenAIRE

    Jelovica, Jasmin; Romanoff, Jani; Ehlers, Sören; Varsta, Petri

    2012-01-01

    This paper investigates the influence of weld rotation stiffness on the global bifurcation buckling strength of laser-welded web-core sandwich plates. The study is carried out using two methods, the first is the equivalent single-layer theory approach solved analytically for simply supported plates and numerically for clamped plates. First-order shear deformation theory is used. The second method is the three-dimensional model of a sandwich plate solved with finite element method. Both approa...

  6. Sandwiched zinc-finger nucleases demonstrating higher homologous recombination rates than conventional zinc-finger nucleases in mammalian cells.

    Science.gov (United States)

    Mori, Tomoaki; Mori, Koichi; Tobimatsu, Takamasa; Sera, Takashi

    2014-02-01

    We previously reported that our sandwiched zinc-finger nucleases (ZFNs), in which a DNA cleavage domain is inserted between two artificial zinc-finger proteins, cleave their target DNA much more efficiently than conventional ZFNs in vitro. In the present study, we compared DNA cleaving efficiencies of a sandwiched ZFN with those of its corresponding conventional ZFN in mammalian cells. Using a plasmid-based single-strand annealing reporter assay in HEK293 cells, we confirmed that the sandwiched ZFN induced homologous recombination more efficiently than the conventional ZFN; reporter activation by the sandwiched ZFN was more than eight times that of the conventional one. Western blot analysis showed that the sandwiched ZFN was expressed less frequently than the conventional ZFN, indicating that the greater DNA-cleaving activity of the sandwiched ZFN was not due to higher expression of the sandwiched ZFN. Furthermore, an MTT assay demonstrated that the sandwiched ZFN did not have any significant cytotoxicity under the DNA-cleavage conditions. Thus, because our sandwiched ZFN cleaved more efficiently than its corresponding conventional ZFN in HEK293 cells as well as in vitro, sandwiched ZFNs are expected to serve as an effective molecular tool for genome editing in living cells.

  7. Parametric study on nonlinear vibration of composite truss core sandwich plate with internal resonance

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jia Nen; Liu, Jun [Tianjin Key Laboratory of the Design and Intelligent Control of the Advanced Mechatronical System, Tianjin University of Technology, Tianjin (China); Zhang, Wei; Yao, Ming Hui [College of Mechanical Engineering, Beijing University of Technology, Beijing (China); Sun, Min [School of Science, Tianjin Chengjian University, Tianjin (China)

    2016-09-15

    Nonlinear vibrations of carbon fiber reinforced composite sandwich plate with pyramidal truss core are investigated. The governing equation of motion for the sandwich plate is derived by using a Zig-Zag theory under consideration of geometrically nonlinear. The natural frequencies of sandwich plates with different dimensions are calculated and compared with those obtained from the classic laminated plate theory and Reddy's third-order shear deformation plate theory. The frequency responses and waveforms of the sandwich plate when 1:3 internal resonance occurs are obtained, and the characteristics of the internal resonance are discussed. The influences of layer number of face sheet, strut radius, core height and inclination angle on the nonlinear responses of the sandwich plate are analyzed. The results demonstrate that the strut radius and inclination angle mainly affect the resonance frequency band of the sandwich plate, and the layer number and core height not only influence the resonance frequency band but also significantly affect the response amplitude.

  8. An Analysis of Nondestructive Evaluation Techniques for Polymer Matrix Composite Sandwich Materials

    Science.gov (United States)

    Cosgriff, Laura M.; Roberts, Gary D.; Binienda, Wieslaw K.; Zheng, Diahua; Averbeck, Timothy; Roth, Donald J.; Jeanneau, Philippe

    2006-01-01

    Structural sandwich materials composed of triaxially braided polymer matrix composite material face sheets sandwiching a foam core are being utilized for applications including aerospace components and recreational equipment. Since full scale components are being made from these sandwich materials, it is necessary to develop proper inspection practices for their manufacture and in-field use. Specifically, nondestructive evaluation (NDE) techniques need to be investigated for analysis of components made from these materials. Hockey blades made from sandwich materials and a flat sandwich sample were examined with multiple NDE techniques including thermographic, radiographic, and shearographic methods to investigate damage induced in the blades and flat panel components. Hockey blades used during actual play and a flat polymer matrix composite sandwich sample with damage inserted into the foam core were investigated with each technique. NDE images from the samples were presented and discussed. Structural elements within each blade were observed with radiographic imaging. Damaged regions and some structural elements of the hockey blades were identified with thermographic imaging. Structural elements, damaged regions, and other material variations were detected in the hockey blades with shearography. Each technique s advantages and disadvantages were considered in making recommendations for inspection of components made from these types of materials.

  9. Development of a finite element model for the simulation of parabolic impact of sandwich panels

    Science.gov (United States)

    Ram Ramakrishnan, Karthik; Guérard, Sandra; Mahéo, Laurent; Shankar, Krishna; Viot, Philippe

    2015-09-01

    Sandwich panels are lightweight structures of two thin high strength facesheets bonded to either side of a thick low density core such as foams and honeycombs. It is necessary to study the impact response of sandwich structures in order to ensure the reliability and safety of these structures. The response of sandwich panels to impact loading is usually studied for impact at normal angle of incidence. In real engineering situations, the structures are more frequently loaded at some oblique angle or with a complex trajectory. It is easy to carry out normal impact tests using devices like the drop tower, but impacts at oblique angles are difficult to characterise experimentally. A tri-dimensional impact device called Hexapod has been developed to experimentally study the impact loading of sandwich plates with a parabolic trajectory. The Hexapod is a modified Gough-Stewart platform that can be moved independently in the six degrees of freedom, corresponding to three translation axes and three rotation axes. In this paper, an approach for modelling the parabolic impact of sandwich structures with thin metallic facesheets and polymer foam core using commercial finite element code LS-DYNA software is presented. The results of the FE model of sandwich panels are compared with experimental data in terms of the time history of vertical and horizontal components of force. A comparison of the strain history obtained from Digital Image Correlation and LS-Dyna model are also presented.

  10. Mechanical properties of sandwich composite made of syntactic foam core and GFRP skins

    Directory of Open Access Journals (Sweden)

    Zulzamri Salleh

    2016-12-01

    Full Text Available Sandwich composites or sandwich panels have been widely used as potential materials or building structures and are regarded as a lightweight material for marine applications. In particular, the mechanical properties, such as the compressive, tensile and flexural behaviour, of sandwich composites formed from glass fibre sheets used as the skin and glass microballoon/vinyl ester as the syntactic foam core were investigated in this report. This syntactic foam core is sandwiched between unidirectional glass fibre reinforced plastic (GFRP using vinyl ester resins to build high performance sandwich panels. The results show that the compressive and tensile strengths decrease when the glass microballoon content is increased in syntactic foam core of sandwich panels. Moreover, compressive modulus is also found to be decreased, and there is no trend for tensile modulus. Meanwhile, the flexural stiffness and effective flexural stiffness for edgewise position have a higher bending as 50% and 60%, respectively. Furthermore, the results indicated that the glass microballoon mixed in a vinyl ester should be controlled to obtain a good combination of the tensile, compressive and flexural strength properties.

  11. Evaluation and selection of indirect ELISA and sandwich ELISA kits for anti-HCV detection

    Directory of Open Access Journals (Sweden)

    LI Yongzhen

    2014-10-01

    Full Text Available ObjectiveTo compare the sensitivity and specificity between indirect enzyme-linked immunosorbent assay (ELISA and double-antibody sandwich ELISA kits produced in China and to select the best ELISA kit. MethodsSamples for evaluation included 60 serum plates and 40 serum samples positive or weakly positive for antibody to hepatitis C virus (anti-HCV which were confirmed by recombinant immunoblot assay. These samples were tested with a sandwich ELISA kit and three indirect ELISA kits, all of which were produced in China. Comparison between ELISA kits was made by paired chi-square test; comparison of false negative rate was made by R×C contingency table test. ResultsThe sensitivities of three indirect ELISA kits and a sandwich ELISA kit were 90.2%, 78.0%, 95.1%, and 97.6%, respectively, and the specificities were 78.1%, 72.6%, 94.1%, and 100%, respectively. The sandwich ELISA kit had a 4-8 times higher sensitivity than indirect ELISA kits. The R×C contingency table test revealed significant differences in false negative rate between ELISA kits and combinations of ELISA kits (χ2=29.898, P<0.05. ConclusionSandwich ELISA kit has higher sensitivity and specificity than indirect ELISA kits. Combined use of sandwich ELISA and indirect ELISA kits can significantly reduce the false negative rate and effectively prevent missed anti-HCV detection.

  12. Development of a finite element model for the simulation of parabolic impact of sandwich panels

    Directory of Open Access Journals (Sweden)

    Ramakrishnan Karthik Ram

    2015-01-01

    Full Text Available Sandwich panels are lightweight structures of two thin high strength facesheets bonded to either side of a thick low density core such as foams and honeycombs. It is necessary to study the impact response of sandwich structures in order to ensure the reliability and safety of these structures. The response of sandwich panels to impact loading is usually studied for impact at normal angle of incidence. In real engineering situations, the structures are more frequently loaded at some oblique angle or with a complex trajectory. It is easy to carry out normal impact tests using devices like the drop tower, but impacts at oblique angles are difficult to characterise experimentally. A tri-dimensional impact device called Hexapod has been developed to experimentally study the impact loading of sandwich plates with a parabolic trajectory. The Hexapod is a modified Gough-Stewart platform that can be moved independently in the six degrees of freedom, corresponding to three translation axes and three rotation axes. In this paper, an approach for modelling the parabolic impact of sandwich structures with thin metallic facesheets and polymer foam core using commercial finite element code LS-DYNA software is presented. The results of the FE model of sandwich panels are compared with experimental data in terms of the time history of vertical and horizontal components of force. A comparison of the strain history obtained from Digital Image Correlation and LS-Dyna model are also presented.

  13. Failure Predictions of Out-of-Autoclave Sandwich Joints with Delaminations Under Flexure Loads

    Science.gov (United States)

    Nordendale, Nikolas A.; Goyal, Vinay K.; Lundgren, Eric C.; Patel, Dhruv N.; Farrokh, Babak; Jones, Justin; Fischetti, Grace; Segal, Kenneth N.

    2015-01-01

    An analysis and a test program was conducted to investigate the damage tolerance of composite sandwich joints. The joints contained a single circular delamination between the face-sheet and the doubler. The coupons were fabricated through out-of-autoclave (OOA) processes, a technology NASA is investigating for joining large composite sections. The four-point bend flexure test was used to induce compression loading into the side of the joint where the delamination was placed. The compression side was chosen since it tends to be one of the most critical loads in launch vehicles. Autoclave cure was used to manufacture the composite sandwich sections, while the doubler was co-bonded onto the sandwich face-sheet using an OOA process after sandwich panels were cured. A building block approach was adopted to characterize the mechanical properties of the joint material, including the fracture toughness between the doubler and face-sheet. Twelve four-point-bend samples were tested, six in the sandwich core ribbon orientation and six in sandwich core cross-ribbon direction. Analysis predicted failure initiation and propagation at the pre-delaminated location, consistent with experimental observations. A building block approach using fracture analyses methods predicted failure loads in close agreement with tests. This investigation demonstrated a small strength reduction due to a flaw of significant size compared to the width of the sample. Therefore, concerns of bonding an OOA material to an in-autoclave material was mitigated for the geometries, materials, and load configurations considered.

  14. PENGGUNAAN SANDWICH PLATE SYSTEM (SPS PADA KONSTRUKSI INNER BOTTOM

    Directory of Open Access Journals (Sweden)

    Ahmad Baidowi

    2015-06-01

    Full Text Available Perkembangan teknologi yang semakin maju memberikan alternatif-alternatif dalam memperbaiki berbagai bentuk sistem, termasuk di dalamnya konstruksi struktur kapal. Latar belakang dari penelitian ini adalah pada permasalahan kebutuhan material ringan pada kapal, kecepatan proses produksi, penyederhanaan konstruksi dan biaya perawatan kapal yang rendah. Penggunaan material ringan Sandwich Plate System (SPS menjadi salah satu jawaban dari permasalahan-permasalahan tersebut, penggunaan SPS dapat menyederhanakan bentuk dari konstruksi kapal dengan menghilangkan penegar inner bottom longitudinal dan mampu mengurangi Light Weight Tonnase (LWT. Artikel ini membahas perbandingan pola distribusi tegangan dan deformasi pada konstruksi bottom yang menggunakan SPS dan baja AH36, selain dari itu juga mengetahui seberapa besar pengurangan LWT yang dihasilkan untuk meningkatkan Payload kapal. Analisa dilakukan dengan simulasi numerik berdasarkan FEM pada konstruksi inner bottom dengan pembebanan muatan. Dari hasil simulasi didapatkan besar tegangan maksimal untuk material baja AH36 sebesar 226 Mpa dengan menggunakan penegar, sedangkan konstuksi dengan material SPS tegangan maksimal yang dihasilkan sebesar 221 Mpa tanpa penggunaan penegar, dengan deformasi maksimal untuk AH36 dan SPS yaitu 77 mm yang terjadi pada bagian tengah blok konstruksi inner bottom. Dengan hilangnya penegar berat konstruksi berkurang sebesar 13,05% dari penggunaan material baja AH36 sehingga memberikan peningkatan payload sebesar 13,05%. Simulasi penelitian dilakukan pada kapal Bulk Carrier (BC.

  15. Piezoelectric performance of fluor polymer sandwiches with different void structures

    Science.gov (United States)

    Lou, Kexing; Zhang, Xiaoqing; Xia, Zhongfu

    2012-06-01

    Film sandwiches, consisting of two outer layers of fluoroethylenepropylene and one middle layer of patterned porous polytetrafluoroethylene, were prepared by patterning and fusion bonding. Contact charging was conducted to render the films piezoelectric. The critical voltage to trigger air breakdown in the inner voids in the fabricated films was investigated. The piezoelectric d 33 coefficients were measured employing the quasistatic method and dielectric resonance spectrum. The results show that the critical voltage for air breakdown in the inner voids is associated with the void microstructure of the films. For the films with patterning factors of 0%, 25% and 44%, the critical values are 300, 230 and 230 kV/cm, respectively. With an increase in the patterning factor, both the piezoelectric d 33 coefficients determined from the dielectric resonance spectra and those determined from quasistatic measurements increase, which might be due to a decrease in Young's modulus for the films. The nonlinearity of d 33 becomes increasingly obvious as the patterning factor increases.

  16. Sandwiched structural panel having a bi-directional core structure

    Science.gov (United States)

    Weddendorf, Bruce (Inventor)

    1995-01-01

    A structural panel assembly has a bi-directional core structure sandwiched between and secured to a pair of outer side wall members. The core structure is formed from first and second perpendicular series of elongated strip members having crenelated configurations. The strip members in the first series thereof are transversely interwoven with the strip members in the second series thereof in a manner such that crest portions of the strip members in the first series overlie and oppose trough portions of the strip members in the second series, and trough portions of the strip members in the first series underlie and oppose crest portions of the strip members in the second series. The crest portions of all of the strip members lie generally in a first plane and are secured to the inner side of one of the panel assembly outer side walls, and the trough portions of all of the strip members lie generally in a second plane and are secured to the inner side of the other panel assembly outer side wall.

  17. Efficient transport of droplet sandwiched between saw-tooth plates.

    Science.gov (United States)

    Wang, Liya; Wu, Hengan; Wang, Fengchao

    2016-01-15

    The transport of droplet sandwiched between smooth and saw-tooth plates was investigated using molecular dynamics method. The repeated opening and closing of the plates result in sequential stretching and squeezing of the droplet, which provide the driving force. The asymmetrical saw tooth obstructs the backward motion of the droplet, and gives rise to a net forward displacement of the droplet in every opening and closing cycle. This unidirectional motion facilitates the efficient droplet transport, which is referred to as the ratchet-like effect in this work. Our simulations also reveal that the influence of the surface wettability on the droplet transport is different for saw-tooth and smooth plates. Droplet transport efficiency exhibits monotonic decrease with the increase of the solid-liquid interactions for saw-tooth plates. While for smooth plates, unidirectional droplet movement was only observed for certain solid-liquid interactions. Taken together these simulation results and theoretical analysis, we demonstrate that hydrophobic saw-tooth plates can improve the transport efficiency significantly. These findings not only enhance our understanding of the droplet transport from atomistic scale, but also are beneficial to practical applications in designing of micro- and nano-fluidic systems.

  18. GAMBE: multipurpose sandwich detector for neutrons and photons

    Science.gov (United States)

    Ahmed, A.; Burdin, S.; Casse, G.; van Zalinge, H.; Powel, S.; Rees, J.; Smith, A.; Tsurin, I.

    2016-10-01

    Detectors made with semiconductors such as silicon can be efficiently used for detecting and imaging neutrons when coated with suitable materials. They detect the charged reaction products resulting from the interaction of thermal neutrons with materials with high capture cross section like 10B, 6Li, and 6LiF. This work describes the performance of a thermal neutron detector system, GAMBE, which is based on silicon sensors and a layer of neutron-sensitive material, such as a lithium fluoride film or a lithium-6 foil, in a sandwich configuration. This arrangement has a total detection efficiency of 4 +/- 2 %, 7 +/- 1 %, and12 +/- 1 % for 7 μm 6LiF film, 40 μm and 70 μm 6Li foil respectively. Also, it enhances the rejection of fake hits using a simple coincidence method. The coincidence that defines a true neutron hit is the simultaneous signal recorded by the two sensors facing the conversion layer (or foil). These coincidences provide a very good method for rejecting the spurious hits coming from gamma-rays, which are usually present in the neutron field under measurement. The GAMBE system yields a rejection factor at the level of 108 allowing very pure neutron detection in high gamma background conditions. However, the price to pay is a reduction of the detection efficiency of 1 +/- 1 % or 0:9 +/- 0:3 % for 7 μm 6LiF film and 40 μm 6Li foil respectively.

  19. Magnetic ordering in Fe/Co sandwiches on Cu(100).

    Science.gov (United States)

    Razee, S S A; Staunton, J B; Szunyogh, L

    2009-07-01

    We investigate magnetic correlations and local magnetic moments at finite temperatures of some Fe and Co multilayers on Cu(100) substrates, such as Co(m)Fe(n)Co(m)/Cu(100) and Fe(m)Co(n)Fe(m)/Cu(100). We use an ab initio mean-field theory of magnetic fluctuations for layered materials based on the first-principles local spin-density functional theory implemented through the screened Korringa-Kohn-Rostoker method. We find that the presence of Fe layers in the neighbourhood of a Co layer always leads to a reduction in the magnetic moment of the Co atoms, whereas that of the Fe atoms is enhanced. Of particular interest is the lack of local moment formation on the single fcc-Co layer sandwiched between two fcc-Fe layers. However, a Co layer completely immersed in a Cu environment remains ferromagnetic. The Curie temperature of the Co(m)Fe(n)Co(m)/Cu(100) system oscillates as the Fe layer thickness is increased whereas that of the Fe(m)Co(n)Fe(m)/Cu(100) system increases almost monotonically with Co layer thickness.

  20. Numerical investigation of blanking for metal polymer sandwich sheets

    Directory of Open Access Journals (Sweden)

    Gutknecht Florian

    2016-01-01

    Full Text Available Metal polymer sandwich sheets consist of materials with drastically different mechanical properties. Due to this fact and because of high local gradients in the cutting zone during the blanking process, traditional process strategies and empirical knowledge are difficult to apply. A finite-element simulation of the shear cutting process is used to predict the necessary force and the geometry of the cutting surface. A fully-coupled ductile damage model is used for the description of the material behaviour. This model considers the influence of shear and compression-dominated stress states on the initiation of damage. Experimental tensile and compression test data is used for the identification of material parameters. The results of the blanking simulation are compared with experimental data. Furthermore, the evolution of the stress state is analysed to gain understanding of the underlying physics. Finally this model enables the prediction of core compression and other quantities such as the acting stresses and corresponding triaxilities, which provide valuable information for the development of analytical models.

  1. UHPC SANDWICH STRUCTURES WITH COMPOSITE COATING UNDER COMPRESSIVE LOAD

    Directory of Open Access Journals (Sweden)

    Jan Markowski

    2016-12-01

    Full Text Available Ultra-high-performance concrete (UHPC sandwich structures with composite coating serve as multipurpose load-bearing elements. The UHPC’s extraordinary compressive strength is used in a multi-material construction element, while issues regarding the concrete’s brittle failure behaviour are properly addressed. A hollow section concrete core is covered by two steel tubes. The outer steel tube is wrapped in a composite material. By this design, UHPC is used in a material- and shape-optimised way with a low dead weight ratio[1] concerning the load-bearing capacity and stability[2]. The cross-section’s hollow shape optimises the construction’s buckling stability while saving self-weight. The composite coating on the column’s outside functions both as a layer increasing the construction’s durability and as a structural component increasing the the maximum and the residual load capacity. Investigations on the construction’s structural behaviour were performed.

  2. Sandwich module prototype progress for space solar power

    Science.gov (United States)

    Jaffe, Paul; Hodkin, Jason; Harrington, Forest; Person, Clark; Nurnberger, Michael; Nguyen, Bang; LaCava, Susie; Scheiman, Dave; Stewart, Grant; Han, Andrew; Hettwer, Ethan; Rhoades, Daniel

    2014-02-01

    Space solar power (SSP) has been broadly defined as the collection of solar energy in space and its wireless transmission for use on earth. This approach potentially gives the benefit of provision of baseload power while avoiding the losses due to the day/night cycle and tropospheric effects that are associated with terrestrial solar power. Proponents have contended that the implementation of such systems could offer energy security, environmental, and technological advantages to those who would undertake their development. Among recent implementations commonly proposed for SSP, the modular symmetrical concentrator (MSC) and other modular concepts have received considerable attention. Each employs an array of modules for performing conversion of concentrated sunlight into microwaves or laser beams for transmission to earth. While prototypes of such modules have been designed and developed previously by several groups, none have been subjected to the challenging conditions inherent to the space environment and the possible solar concentration levels in which an array of modules might be required to operate. The research described herein details our team's efforts in the development of photovoltaic arrays, power electronics, microwave conversion electronics, and antennas for microwave-based "sandwich" module prototypes. The implementation status and testing results of the prototypes are reviewed.

  3. Variable stiffness sandwich panels using electrostatic interlocking core

    Science.gov (United States)

    Heath, Callum J. C.; Bond, Ian P.; Potter, Kevin D.

    2016-04-01

    Structural topology has a large impact on the flexural stiffness of a beam structure. Reversible attachment between discrete substructures allows for control of shear stress transfer between structural elements, thus stiffness modulation. Electrostatic adhesion has shown promise for providing a reversible latching mechanism for controllable internal connectivity. Building on previous research, a thin film copper polyimide laminate has been used to incorporate high voltage electrodes to Fibre Reinforced Polymer (FRP) sandwich structures. The level of electrostatic holding force across the electrode interface is key to the achievable level of stiffness modulation. The use of non-flat interlocking core structures can allow for a significant increase in electrode contact area for a given core geometry, thus a greater electrostatic holding force. Interlocking core geometries based on cosine waves can be Computer Numerical Control (CNC) machined from Rohacell IGF 110 Foam core. These Interlocking Core structures could allow for enhanced variable stiffness functionality compared to basic planar electrodes. This novel concept could open up potential new applications for electrostatically induced variable stiffness structures.

  4. Homogeneous and sandwich active panels under deterministic and stochastic excitation.

    Science.gov (United States)

    Rohlfing, J; Gardonio, P

    2009-06-01

    In this paper an element-based model is used to predict the structural response and sound radiation of two smart panels excited by (a) an acoustic plane wave, (b) a stochastic acoustic diffuse field, and (c) a turbulent boundary layer. The first panel is made of aluminum, while the second is a composite sandwich panel with equivalent static stiffness but four times lower mass per unit area. The panels are equipped with 16 decentralized velocity feedback control loops using idealized point force actuators. In contrast to previous studies on smart panels, the analysis is extended to the upper end of the audio frequency range. In this frequency region the response and sound radiation of the panels strongly depend on the spatial characteristics of the excitation field and the sound radiation properties with respect to the bending wavelength on the panels. Considerable reduction in structural response and sound radiation is predicted for the low audio frequency range where the panel response is dominated by well separated resonances of low order structural modes. It is also found that some reduction can be achieved around acoustic and convective coincidence regions.

  5. Dispersion of Lamb waves in a honeycomb composite sandwich panel.

    Science.gov (United States)

    Baid, Harsh; Schaal, Christoph; Samajder, Himadri; Mal, Ajit

    2015-02-01

    Composite materials are increasingly being used in advanced aircraft and aerospace structures. Despite their many advantages, composites are often susceptible to hidden damages that may occur during manufacturing and/or service of the structure. Therefore, safe operation of composite structures requires careful monitoring of the initiation and growth of such defects. Ultrasonic methods using guided waves offer a reliable and cost effective method for defects monitoring in advanced structures due to their long propagation range and their sensitivity to defects in their propagation path. In this paper, some of the useful properties of guided Lamb type waves are investigated, using analytical, numerical and experimental methods, in an effort to provide the knowledge base required for the development of viable structural health monitoring systems for composite structures. The laboratory experiments involve a pitch-catch method in which a pair of movable transducers is placed on the outside surface of the structure for generating and recording the wave signals. The specific cases considered include an aluminum plate, a woven composite laminate and an aluminum honeycomb sandwich panel. The agreement between experimental, numerical and theoretical results are shown to be excellent in certain frequency ranges, providing a guidance for the design of effective inspection systems.

  6. Enzymatic detection of formalin-fixed museum specimens for DNA analysis and enzymatic maceration of formalin-fixed specimens

    DEFF Research Database (Denmark)

    Sørensen, Margrethe; Redsted Rasmussen, Arne; Simonsen, Kim Pilkjær

    2016-01-01

    % ethanol. The method was subsequently tested on wild-living preserved specimens and an archived specimen. The protease enzyme used was SavinaseH 16 L, Type EX from Novozymes A/S. The enzymatic screening test demands only simple laboratory equipment. The method is useful for natural history collections...... in museums where DNA analyses of archived specimens are performed. Wasted time and resources can be avoided through the detection of formalin-fixed specimens because these specimens yield low-quality, damaged DNA. In addition to the screening method, it is shown that formalin-preserved specimens can...

  7. Reheating of zinc-titanate sintered specimens

    Directory of Open Access Journals (Sweden)

    Labus N.

    2015-01-01

    Full Text Available The scope of this work was observing dimensional and heat transfer changes in ZnTiO3 samples during heating in nitrogen and air atmosphere. Interactions of bulk specimens with gaseous surrounding induce microstructure changes during heating. Sintered ZnTiO3 nanopowder samples were submitted to subsequent heating. Dilatation curves and thermogravimetric with simultaneous differential thermal analysis TGA/DTA curves were recorded. Reheating was performed in air and nitrogen atmospheres. Reheated samples obtained at different characteristic temperatures in air were analyzed by X-ray diffraction (XRD. Microstructures obtained by scanning electron microscopy (SEM of reheated sintered samples are presented and compared. Reheating in a different atmosphere induced different microstructures. The goal was indicating possible causes leading to the microstructure changes. [Projekat Ministarstva nauke Republike Srbije, br. OI172057 i br. III45014

  8. Dissolution of bulk specimens of silicon nitride

    Science.gov (United States)

    Davis, W. F.; Merkle, E. J.

    1981-01-01

    An accurate chemical characterization of silicon nitride has become important in connection with current efforts to incorporate components of this material into advanced heat engines. However, there are problems concerning a chemical analysis of bulk silicon nitride. Current analytical methods require the pulverization of bulk specimens. A pulverization procedure making use of grinding media, on the other hand, will introduce contaminants. A description is given of a dissolution procedure which overcomes these difficulties. It has been found that up to at least 0.6 g solid pieces of various samples of hot pressed and reaction bonded silicon nitride can be decomposed in a mixture of 3 mL hydrofluoric acid and 1 mL nitric acid overnight at 150 C in a Parr bomb. High-purity silicon nitride is completely soluble in nitric acid after treatment in the bomb. Following decomposition, silicon and hydrofluoric acid are volatilized and insoluble fluorides are converted to a soluble form.

  9. Tensile test of dumbbell-shaped specimen in thickness direction

    Science.gov (United States)

    Iizuka, Takashi

    2016-10-01

    Sheet metal forming is widely used in manufacturing shops, and evaluation of forming limit for sheet metal is important. However, specimen shape influences on the fracture of the sheet metal. As one of methods to decrease these effects, an uniaxial tensile test using specimen dumbbell-shaped in thickness direction had been examined using FEM analysis. In this study, actually specimen dumbbell-shaped in thickness direction was fabricated using a new incremental sheet forging method, and uniaxial tensile test was conducted. Load-stroke diagram, fracture morphologies, stress-strain curves and shape after fracture were investigated, and effects of specimen shape were considered. Elongation was larger as using specimen dumbbell-shaped in the width direction. Stress-strain curves until necking occurred were less influenced by specimen shape. However, yield stress decreased and local elongation increased as using specimen dumbbell-shaped in the width direction. The reasons why these tendencies showed were considered in the view of specimen shapes.

  10. A new specimen management system using RFID technology.

    Science.gov (United States)

    Shim, Hun; Uh, Young; Lee, Seung Hwan; Yoon, Young Ro

    2011-12-01

    The specimen management system with barcode needs to be improved in order to solve inherent problems in work performance. This study describes the application of Radio Frequency Identification (RFID) which is the solution for the problems associated with specimen labeling and management. A new specimen management system and architecture with RFID technology for clinical laboratory was designed. The suggested system was tested in various conditions such as durability to temperature and aspect of effective utilization of new work flow under a virtual hospital clinical laboratory environment. This system demonstrates its potential application in clinical laboratories for improving work flow and specimen management. The suggested specimen management system with RFID technology has advantages in comparison to the traditional specimen management system with barcode in the aspect of mass specimen processing, robust durability of temperature, humidity changes, and effective specimen tracking.

  11. A non-destructive DNA sampling technique for herbarium specimens.

    Science.gov (United States)

    Shepherd, Lara D

    2017-01-01

    Herbarium specimens are an important source of DNA for plant research but current sampling methods require the removal of material for DNA extraction. This is undesirable for irreplaceable specimens such as rare species or type material. Here I present the first non-destructive sampling method for extracting DNA from herbarium specimens. DNA was successfully retrieved from robust leaves and/or stems of herbarium specimens up to 73 years old.

  12. Drone Transport of Microbes in Blood and Sputum Laboratory Specimens.

    Science.gov (United States)

    Amukele, Timothy K; Street, Jeff; Carroll, Karen; Miller, Heather; Zhang, Sean X

    2016-10-01

    Unmanned aerial vehicles (UAVs) could potentially be used to transport microbiological specimens. To examine the impact of UAVs on microbiological specimens, blood and sputum culture specimens were seeded with usual pathogens and flown in a UAV for 30 ± 2 min. Times to recovery, colony counts, morphologies, and matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS)-based identifications of the flown and stationary specimens were similar for all microbes studied.

  13. The type specimen of Anoura geoffroyi lasiopyga (Chiroptera: Phyllostomidae)

    Science.gov (United States)

    Arroyo-Cabrales, Joaquin; Gardner, A.L.

    2003-01-01

    In 1868, Wilhelm Peters described Glossonycteris lasiopyga, based on a specimen provided by Henri de Saussure and collected in Mexico. The type specimen was presumed to be among those housed in the collections of the Zoologisches Museum of the Humboldt Universitat in Berlin, Germany. Our study of one of Saussure?s specimens from Mexico, discovered in the collections of the Museum d?Histoire Naturelle, Geneva, Switzerland, demonstrates that it and not one of the Berlin specimens is the holotype.

  14. Elastic-plastic analysis of the SS-3 tensile specimen

    Energy Technology Data Exchange (ETDEWEB)

    Majumdar, S. [Argonne National Lab., IL (United States)

    1998-09-01

    Tensile tests of most irradiated specimens of vanadium alloys are conducted using the miniature SS-3 specimen which is not ASTM approved. Detailed elastic-plastic finite element analysis of the specimen was conducted to show that, as long as the ultimate to yield strength ratio is less than or equal to 1.25 (which is satisfied by many irradiated materials), the stress-plastic strain curve obtained by using such a specimen is representative of the true material behavior.

  15. A quantitative exposure model simulating human norovirus transmission during preparation of deli sandwiches.

    Science.gov (United States)

    Stals, Ambroos; Jacxsens, Liesbeth; Baert, Leen; Van Coillie, Els; Uyttendaele, Mieke

    2015-03-02

    Human noroviruses (HuNoVs) are a major cause of food borne gastroenteritis worldwide. They are often transmitted via infected and shedding food handlers manipulating foods such as deli sandwiches. The presented study aimed to simulate HuNoV transmission during the preparation of deli sandwiches in a sandwich bar. A quantitative exposure model was developed by combining the GoldSim® and @Risk® software packages. Input data were collected from scientific literature and from a two week observational study performed at two sandwich bars. The model included three food handlers working during a three hour shift on a shared working surface where deli sandwiches are prepared. The model consisted of three components. The first component simulated the preparation of the deli sandwiches and contained the HuNoV reservoirs, locations within the model allowing the accumulation of NoV and the working of intervention measures. The second component covered the contamination sources being (1) the initial HuNoV contaminated lettuce used on the sandwiches and (2) HuNoV originating from a shedding food handler. The third component included four possible intervention measures to reduce HuNoV transmission: hand and surface disinfection during preparation of the sandwiches, hand gloving and hand washing after a restroom visit. A single HuNoV shedding food handler could cause mean levels of 43±18, 81±37 and 18±7 HuNoV particles present on the deli sandwiches, hands and working surfaces, respectively. Introduction of contaminated lettuce as the only source of HuNoV resulted in the presence of 6.4±0.8 and 4.3±0.4 HuNoV on the food and hand reservoirs. The inclusion of hand and surface disinfection and hand gloving as a single intervention measure was not effective in the model as only marginal reductions of HuNoV levels were noticeable in the different reservoirs. High compliance of hand washing after a restroom visit did reduce HuNoV presence substantially on all reservoirs. The

  16. Study on the performance of infrared thermal imaging light source for detection of impact defects in CFRP composite sandwich panels

    Energy Technology Data Exchange (ETDEWEB)

    Park, Hee Sang [R and D, Korea Research Institute of Smart Material and Structures System Association, Daejeon (Korea, Republic of); Choi, Man Yong; Kwon, Koo Ahn; Park, Jeong Hak; Choi, Won Jae [Safety measurement center, Korea research Institute of Standards and Science, Daejeon (Korea, Republic of); Jung, Hyun Chul [Dept. of Mechanical Engineering Chosun University, Gwangju (Korea, Republic of)

    2017-04-15

    Recently, composite materials have been mainly used in the main wings, ailerons, and fuselages of aircraft and rotor blades of helicopters. Composite materials used in rapid moving structures are subject to impact by hail, lightning, and bird strike. Such an impact can destroy fiber tissues in the composite materials as well as deform the composite materials, resulting in various problems such as weakened rigidity of the composite structure and penetration of water into tiny cracks. In this study, experiments were conducted using a 2 kW halogen lamp which is most frequently used as a light source, a 2 kW near-infrared lamp, which is used for heating to a high temperature, and a 6 kW xenon flash lamp which emits a large amount of energy for a moment. CFRP composite sandwich panels using Nomex honeycomb core were used as the specimens. Experiments were carried out under impact damages of 1, 4 and 8 J. It was found that the detection of defects was fast when the xenon flash lamp was used. The detection of damaged regions was excellent when the halogen lamp was used. Furthermore, the near-infrared lamp is an effective technology for showing the surface of a test object.

  17. Fixture For Hot Stress Tests Of Thin Specimens

    Science.gov (United States)

    Gates, Thomas S.

    1993-01-01

    Fixture designed to hold and heat thin, rectangular-cross-section specimen of composite material during hot lengthwise-stress test. Suitable for testing same specimen in either tension or compression. Clamps lightly onto specimen, providing both heat via thermal conduction and lateral support needed to prevent buckling during compression test.

  18. 49 CFR 219.205 - Specimen collection and handling.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Specimen collection and handling. 219.205 Section... § 219.205 Specimen collection and handling. (a) General. Urine and blood specimens must be obtained, marked, preserved, handled, and made available to FRA consistent with the requirements of this subpart...

  19. The CAS Bio-specimen Centers in Sound Progress

    Institute of Scientific and Technical Information of China (English)

    LI Liangqian; QIAO Gexia; YAO Yijian

    2010-01-01

    @@ Bio-specimen centers, including herbaria and zoological museums, are the most integrated places for the storage of specimens, which are real samples and the most important vouchers for taxonomic and biodiversity studies.The information carried by the specimens is of substantial reference for research on species distribution, history, status, phylogeny and evolution, etc.

  20. Adaptation of Museum Specimens for Use in Anatomical Teaching Aids

    Science.gov (United States)

    Harris, P. F.; And Others

    1977-01-01

    Color transparencies are prepared of a re-colored anatomical specimen after placing labels temporarily in position to indicate specific structures. The specimen is also radiographed to show skeletal and soft tissue structures. Cross-reference among the specimen, photographs, and radiographs is supplemented by examination and self-assessment…