Heat exchanger inventory cost optimization for power cycles with one feedwater heater

International Nuclear Information System (INIS)

Qureshi, Bilal Ahmed; Antar, Mohamed A.; Zubair, Syed M.

2014-01-01

Highlights: • Cost optimization of heat exchanger inventory in power cycles is investigated. • Analysis for an endoreversible power cycle with an open feedwater heater is shown. • Different constraints on the power cycle are investigated. • The constant heat addition scenario resulted in the lowest value of the cost function. - Abstract: Cost optimization of heat exchanger inventory in power cycles with one open feedwater heater is undertaken. In this regard, thermoeconomic analysis for an endoreversible power cycle with an open feedwater heater is shown. The scenarios of constant heat rejection and addition rates, power as well as rate of heat transfer in the open feedwater heater are studied. All cost functions displayed minima with respect to the high-side absolute temperature ratio (θ 1 ). In this case, the effect of the Carnot temperature ratio (Φ 1 ), absolute temperature ratio (ξ) and the phase-change absolute temperature ratio for the feedwater heater (Φ 2 ) are qualitatively the same. Furthermore, the constant heat addition scenario resulted in the lowest value of the cost function. For variation of all cost functions, the smaller the value of the phase-change absolute temperature ratio for the feedwater heater (Φ 2 ), lower the cost at the minima. As feedwater heater to hot end unit cost ratio decreases, the minimum total conductance required increases

NREL: U.S. Life Cycle Inventory Database - About the LCI Database Project

Science.gov (United States)

About the LCI Database Project The U.S. Life Cycle Inventory (LCI) Database is a publicly available database that allows users to objectively review and compare analysis results that are based on similar source of critically reviewed LCI data through its LCI Database Project. NREL's High-Performance

Life Cycle Inventory Analysis for a Small-Scale Trawl Fishery in Sendai Bay, Japan

Directory of Open Access Journals (Sweden)

Kazuhito Watanabe

2016-04-01

Full Text Available A reduced environmental burden, while maintaining high quality and low cost, has become an important factor for achieving sustainability in the fisheries sector. The authors performed life cycle inventory (LCI analysis targeting the fish production for a small-scale trawl fishery including small trawlers operating in Sendai Bay, Japan. The average annual cumulative CO2 emissions for the small trawlers were 4.7 ton-CO2/ton-product and 8.3 ton-CO2/million Japanese yen (JPN. Total fuel consumption contributed to 97% of the global warming potential. The range of variation in the basic unit of CO2 for each small trawler was also elucidated. Energy conservation through lower fuel consumption is shown to be an effective measure for reducing CO2 in a small trawler fishery. Moreover, the authors examined the system boundary, the determination of the functional unit, and the allocation method of applying LCI analysis to fisheries. Finally, the economy and environment of small trawler fisheries are discussed as important factors for sustainable fisheries, and the life cycle approach is applied to a new fishery type in Japan.

What Inventory Behavior Tells Us about Business Cycles

OpenAIRE

James A. Kahn; Mark Bils

2000-01-01

Manufacturers' finished goods inventories move less than shipments over the business cycle. We argue that this requires marginal cost to be more procyclical than is conventionally measured. We construct, for six manufacturing industries, alternative measures of marginal cost that attribute high-frequency productivity shocks to procyclical work effort, and find that they are much more successful in accounting for inventory behavior. The difference is attributable to cyclicality in the shadow p...

A study on the environmental impacts analysis with life cycle analysis of NPPs

International Nuclear Information System (INIS)

Jeong, H. S.; Moon, K. H.; Youn, S. W.

2003-01-01

This Life Cycle Analysis (LCA) work was accomplished based on the ISO-14040 framework goal and scope definition, including life cycle inventory analysis, and life cycle impact assessment. For the selection of impact categories, resource use, global affairs, local affairs, and nuclear specific affair were considered. It was unexpected that environmental burdens are generally heavier in an electricity generation process than in upper stream and fabrication processes, except ODP and ETPs. It has been normally thought that environmental burden in upper steam would be heavier than those in other processes. This misconception could have originated from the ambiguous thought for end-of-pipe emissions and life cycle inventories

Tritium fuel cycle modeling and tritium breeding analysis for CFETR

Energy Technology Data Exchange (ETDEWEB)

Chen, Hongli; Pan, Lei; Lv, Zhongliang; Li, Wei; Zeng, Qin, E-mail: zengqin@ustc.edu.cn

2016-05-15

Highlights: • A modified tritium fuel cycle model with more detailed subsystems was developed. • The mean residence time method applied to tritium fuel cycle calculation was updated. • Tritium fuel cycle analysis for CFETR was carried out. - Abstract: Attaining tritium self-sufficiency is a critical goal for fusion reactor operated on the D–T fuel cycle. The tritium fuel cycle models were developed to describe the characteristic parameters of the various elements of the tritium cycle as a tool for evaluating the tritium breeding requirements. In this paper, a modified tritium fuel cycle model with more detailed subsystems and an updated mean residence time calculation method was developed based on ITER tritium model. The tritium inventory in fueling system and in plasma, supposed to be important for part of the initial startup tritium inventory, was considered in the updated mean residence time method. Based on the model, the tritium fuel cycle analysis of CFETR (Chinese Fusion Engineering Testing Reactor) was carried out. The most important two parameters, the minimum initial startup tritium inventory (I{sub m}) and the minimum tritium breeding ratio (TBR{sub req}) were calculated. The tritium inventories in steady state and tritium release of subsystems were obtained.

Life cycle inventories for bioenergy and fossil-fuel fired cogeneration plants

International Nuclear Information System (INIS)

Braennstroem-Norberg, B.M.; Dethlefsen, U.

1998-06-01

Life-cycle inventories for heat production from forest fuel, Salix, coal and oil are presented. Data from the Oerebro cogeneration plant are used for the bioenergy and coal cycles, whereas the oil-fired cycle is based on a fictive plant producing 53 MW electricity and 106 MW heat, also located in the town of Oerebro. This life cycle analysis only covers the inventory stage. A complete life cycle analysis also includes an environmental impact assessment. The methods for assessing environmental impact are still being developed and thus this phase has been omitted here. The intention is, instead, to provide an overall perspective of where in the chain the greatest environmental load for each fuel can be found. Production and energy conversion of fuel requires energy, which is often obtained from fossil fuel. This input energy corresponds to about 11% of the extracted amount of energy for oil, 9% for coal, 6% for Salix, whereas it is about 4% for forest fuel. Utilization of fossil fuel in the coal cycle amounts to production of electricity using coal condensation intended for train transports within Poland. In a life cycle perspective, biofuels show 20-30 times lower emissions of greenhouse gases in comparison with fossil fuels. The chains for biofuels also give considerably lower SO 2 emissions than the chains for coal and oil. The coal chain shows about 50% higher NO x emission than the other fuels. Finally, the study illustrates that emission of particles are similar for all sources of energy. The biofuel cycle is assessed to be generally applicable to plants of similar type and size and with similar transport distances. The oil cycle is probably applicable to small-scale cogeneration plants. However, at present there are no cogeneration plants in Sweden that are solely fired with oil. In the case of the coal cycle, deep mining and a relatively long transport distance within Poland have been assumed. If the coal mining had been from open-cast mines, and if the

Inventory charge calculations in the nuclear fuel cycle

International Nuclear Information System (INIS)

Salmon, R.

1975-09-01

Simplified methods are presented for the calculation of inventory charges or carrying charges on fuel, which represent the indirect component of the fuel cycle cost. These methods permit rapid calculation of the changes in fuel cycle cost caused by changes in the amount or timing of fuel cycle expenditures. The methods are developed by applying the discounted cash flow procedure to a single batch of fuel. In typical cases, this would be a batch representing equilibrium or steady-state reactor operation. The cost equations used are the same as those used in the computer code REFCO, described in ORNL-4695, which was based on the discounted cash flow procedure with continuous discounting. Equivalent procedures using the fixed charge rate concept also are developed. This is done in such a way that consistency with the discounted cash flow procedure is maintained. The fixed charge rate used here is defined in terms of tax rates and the interest rates on debt and equity capital. An effective inventory time is also defined. This is a function of the lead or lag time, the interest rates on capital, and the exposure time of the batch. Tabulated values of the effective inventory time and other useful functions, such as the ratio of indirect to direct cost, are included. Cost calculations using these tables agree with those produced by REFCO, the accuracy being within 0.001 mill/kWhr in the cases studied. (U.S.)

How can a life cycle inventory parametric model streamline life cycle assessment in the wooden pallet sector?

DEFF Research Database (Denmark)

Niero, Monia; Di Felice, Francesco; Ren, Jingzheng

2014-01-01

, as the information required for fulfilling the LCI are standard information about the features of the wooden pallet and its manufacturing process. The contribution analysis on the reference product revealed that the most contributing life cycle stages are wood and nails extraction and manufacturing (positive value......This study discusses the use of parameterization within the life cycle inventory (LCI) in the wooden pallet sector, in order to test the effectiveness of LCI parametric models to calculate the environmental impacts of similar products. Starting from a single case study, the objectives of this paper......; these correlations can be used to improve the design of new wooden pallets.The conceptual scheme for defining the model is based on ISO14040-44 standards. First of all, the product system was defined identifying the life cycle of a generic wood pallet, as well as its life cycle stages. A list of independent...

Tritium inventories and tritium safety design principles for the fuel cycle of ITER

International Nuclear Information System (INIS)

Cristescu, I.R.; Cristescu, I.; Doerr, L.; Glugla, M.; Murdoch, D.

2007-01-01

Within the tritium plant of ITER a total inventory of about 2-3 kg will be necessary to operate the machine in the DT phase. During plasma operation, tritium will be distributed in the different sub-systems of the fuel cycle. A tool for tritium inventory evaluation within each sub-system of the fuel cycle is important with respect to both the process of licensing ITER and also for operation. It is very likely that measurements of total tritium inventories may not be possible for all sub-systems; however, tritium accounting may be achieved by modelling its hold-up within each sub-system and by validating these models in real-time against the monitored flows and tritium streams between the sub-systems. To get reliable results, an accurate dynamic modelling of the tritium content in each sub-system is necessary. A dynamic model (TRIMO) for tritium inventory calculation reflecting the design of each fuel cycle sub-systems was developed. The amount of tritium needed for ITER operation has a direct impact on the tritium inventories within the fuel cycle sub-systems. As ITER will function in pulses, the main characteristics that influence the rapid tritium recovery from the fuel cycle as necessary for refuelling are discussed. The confinement of tritium within the respective sub-systems of the fuel cycle is one of the most important safety objectives. The design of the deuterium/tritium fuel cycle of ITER includes a multiple barrier concept for the confinement of tritium. The buildings are equipped with a vent detritiation system and re-circulation type room atmosphere detritiation systems, required for tritium confinement barrier during possible tritium spillage events. Complementarily to the atmosphere detritiation systems, in ITER a water detritiation system for tritium recovery from various sources will also be operated

ORIGEN-based Nuclear Fuel Inventory Module for Fuel Cycle Assessment: Final Project Report

Energy Technology Data Exchange (ETDEWEB)

Skutnik, Steven E. [Univ. of Tennessee, Knoxville, TN (United States). Dept. of Nuclear Engineering

2017-06-19

The goal of this project, “ORIGEN-based Nuclear Fuel Depletion Module for Fuel Cycle Assessment" is to create a physics-based reactor depletion and decay module for the Cyclus nuclear fuel cycle simulator in order to assess nuclear fuel inventories over a broad space of reactor operating conditions. The overall goal of this approach is to facilitate evaluations of nuclear fuel inventories for a broad space of scenarios, including extended used nuclear fuel storage and cascading impacts on fuel cycle options such as actinide recovery in used nuclear fuel, particularly for multiple recycle scenarios. The advantages of a physics-based approach (compared to a recipe-based approach which has been typically employed for fuel cycle simulators) is in its inherent flexibility; such an approach can more readily accommodate the broad space of potential isotopic vectors that may be encountered under advanced fuel cycle options. In order to develop this flexible reactor analysis capability, we are leveraging the Origen nuclear fuel depletion and decay module from SCALE to produce a standalone “depletion engine” which will serve as the kernel of a Cyclus-based reactor analysis module. The ORIGEN depletion module is a rigorously benchmarked and extensively validated tool for nuclear fuel analysis and thus its incorporation into the Cyclus framework can bring these capabilities to bear on the problem of evaluating long-term impacts of fuel cycle option choices on relevant metrics of interest, including materials inventories and availability (for multiple recycle scenarios), long-term waste management and repository impacts, etc. Developing this Origen-based analysis capability for Cyclus requires the refinement of the Origen analysis sequence to the point where it can reasonably be compiled as a standalone sequence outside of SCALE; i.e., wherein all of the computational aspects of Origen (including reactor cross-section library processing and interpolation, input and output

A life cycle greenhouse gas inventory of a tree production system

Science.gov (United States)

Alissa Kendall; E. Gregory McPherson

2012-01-01

PurposeThis study provides a detailed, process-based life cycle greenhouse gas (GHG) inventory of an ornamental tree production system for urban forestry. The success of large-scale tree planting initiatives for climate protection depends on projects being net sinks for CO2 over their entire life cycle....

Time-dependent tritium inventories and flow rates in fuel cycle components of a tokamak fusion reactor

International Nuclear Information System (INIS)

Kuan, W.

1995-01-01

Time-dependent inventories and flow rates for several components of the fuel cycle are modeled and studied through the use of a new modular-type model for the dynamic simulation of the fuel cycle in a fusion reactor. The complex dynamic behavior in the modeled subsystems is analyzed using this new model. Preliminary results using fuel cycle design configurations similar to ITER are presented and analyzed. The inventories and flow rates inside the primary vacuum pumping, fuel cleanup unit and isotope separation system are studied. Ways to minimize the tritium inventory are also assessed. This was performed by looking at various design options that could be used to minimize tritium inventory for specific components. (orig.)

Methodology for systematic analysis and improvement of manufacturing unit process life-cycle inventory (UPLCI)—CO2PE! initiative (cooperative effort on process emissions in manufacturing). Part 1: Methodology description

DEFF Research Database (Denmark)

Kellens, Karel; Dewulf, Wim; Overcash, Michael

2012-01-01

the provision of high-quality data for LCA studies of products using these unit process datasets for the manufacturing processes, as well as the in-depth analysis of individual manufacturing unit processes.In addition, the accruing availability of data for a range of similar machines (same process, different......This report proposes a life-cycle analysis (LCA)-oriented methodology for systematic inventory analysis of the use phase of manufacturing unit processes providing unit process datasets to be used in life-cycle inventory (LCI) databases and libraries. The methodology has been developed...... and resource efficiency improvements of the manufacturing unit process. To ensure optimal reproducibility and applicability, documentation guidelines for data and metadata are included in both approaches. Guidance on definition of functional unit and reference flow as well as on determination of system...

A new tool for life cycle inventories of agricultural machinery operations

Directory of Open Access Journals (Sweden)

Daniela Lovarelli

2016-03-01

Full Text Available The interest in environmental assessments about agricultural processes is fast growing and asking for new tools for accurate impact evaluations. The methodology commonly used to go through these studies is the life cycle assessment, of which the inventory phase (life cycle inventory, LCI is an essential step. For studies focusing on agricultural productions, the completion of LCI is particularly complex: taking into account the pedo-climatic and mechanical operative variability is evidently difficult. However, the prediction of the environmental impact of mechanical operations caused by the agricultural sector is essential to quantify the impact categories for which it is responsible. A new tool, ENVIAM, was developed to complete LCI to guarantee the availability of local data that describe the mechanical and pedo-climatic conditions occurring in the Po Valley area and widely applicable as well. It calculates mechanical power requests, directly consumed inputs (i.e., fuel, lubricant and material consumption of a productive system by taking into account soil texture, specific machinery operations and coupling solutions as defined by the user. A subdivision of working time and defined engine load have been considered to calculate fuel consumption; with regard to outputs, exhaust gases emissions from internal combustion engines have been assessed by evaluating the emissive stages of belonging as stated by the EU Directive. A case study was also performed to highlight the differences that occur when an analysis is fulfilled in a context with features different from the average, and resulted in significant variations for the inventory. In more details, a comparison was carried out both with Ecoinvent database and within ENVIAM. With regard to fuel consumption, by changing the soil texture, the analysis showed a range between 64%-184% for sandy and clay soils, respectively, if compared with medium texture ones. With this tool, local contexts defined

Thorium fuel cycle analysis

Energy Technology Data Exchange (ETDEWEB)

Yamaji, K [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

1980-07-01

Systems analysis of the thorium cycle, a nuclear fuel cycle accomplished by using thorium, is reported in this paper. Following a brief review on the history of the thorium cycle development, analysis is made on the three functions of the thorium cycle; (1) auxiliary system of U-Pu cycle to save uranium consumption, (2) thermal breeder system to exert full capacity of the thorium resource, (3) symbiotic system to utilize special features of /sup 233/U and neutron sources. The effects of the thorium loading in LWR (Light Water Reactor), HWR (Heavy Water Reactor) and HTGR (High Temperature Gas-cooled Reactor) are considered for the function of auxiliary system of U-Pu cycle. Analysis is made to find how much uranium is saved by /sup 233/U recycling and how the decrease in Pu production influences the introduction of FBR (Fast Breeder Reactor). Study on thermal breeder system is carried out in the case of MSBR (Molten Salt Breeder Reactor). Under a certain amount of fissile material supply, the potential system expansion rate of MSBR, which is determined by fissile material balance, is superior to that of FBR because of the smaller specific fissile inventory of MSBR. For symbiotic system, three cases are treated; i) nuclear heat supply system using HTGR, ii) denatured fuel supply system for nonproliferation purpose, and iii) hybrid system utilizing neutron sources other than fission reactor.

Coupling Computer-Aided Process Simulation and Estimations of Emissions and Land Use for Rapid Life Cycle Inventory Modeling

Science.gov (United States)

A methodology is described for developing a gate-to-gate life cycle inventory (LCI) of a chemical manufacturing process to support the application of life cycle assessment in the design and regulation of sustainable chemicals. The inventories were derived by first applying proces...

Environmental impact of producing hardwood lumber using life-cycle inventory

Science.gov (United States)

Richard D. Bergman; S.A. Bowe

2007-01-01

Using sustainable building materials is gaining a significant presence in the United States therefore proving sustainability claims are becoming increasingly more important. Showing wood products as green building materials is vital for the long-term productivity of the wood building industry. This study examined hardwood lumber manufacturing using Life-Cycle Inventory...

Life-cycle inventory of manufacturing hardwood lumber in Southeastern US

Science.gov (United States)

Richard D. Bergman; Scott A. Bowe

2012-01-01

Environmental impacts associated with the building industry have become of increasing importance. Materials and energy consumed during manufacture of building materials such as lumber affect a building’s environmental performance. This study determined environmental impacts of manufacturing hardwood lumber in the southeastern US using the life-cycle inventory method....

Life cycle inventory modeling of phosphorus substitution, losses and crop uptake after land application of organic waste products

DEFF Research Database (Denmark)

Ten Hoeve, Marieke; Bruun, Sander; Naroznova, Irina

2017-01-01

of this study was to develop a relatively easy to use life cycle inventory model, known as PLCI, that could be used to estimate these values. Methods: A life cycle inventory model for P was developed, which estimates the effect of an application of organic waste followed by ordinary fertilizer management...

Dynamic analysis of Korean nuclear fuel cycle with fast reactor systems

International Nuclear Information System (INIS)

Jeong, Chang Joon

2004-12-01

The Korean nuclear fuel cycle scenario was analyzed by the dynamic analysis method, including Pressurized Water Reactor (PWR), Canadian Deuterium Uranium (CANDU) and fast reactor systems. For the once-through fuel cycle model, the existing nuclear power plant construction plan was considered up to 2016, while the nuclear demand growth rate from the year 2016 was assumed to be 1%. After setting up the once-through fuel cycle model, the Korea Advanced Liquid Metal Reactor (KALIMER) scenario was modeled to investigate the fuel cycle parameters. For the analysis of the fast reactor fuel cycle, both KAILMER-150 and KALIMER-600 reactors were considered. In this analysis, the spent fuel inventory as well as the amount of plutonium, Minor Actinides (MA) and Fission Products (FP) of the recycling fuel cycle was estimated and compared to that of the once-through fuel cycle. Results of the once-through fuel cycle calculation showed that the demand grows up to 64 GWe and total amount of spent fuel would be ∼102 kt in 2100. If the KALIMER scenario is implemented, the total spent fuel inventory can be reduced by ∼80%. However it was found that the KALIMER scenario does not contribute to reduce the amount of MA and FP, which is important when designing a repository. For the further destruction of MA, an actinide burner can be considered in the future nuclear fuel cycle

Inventory parameters

CERN Document Server

Sharma, Sanjay

2017-01-01

This book provides a detailed overview of various parameters/factors involved in inventory analysis. It especially focuses on the assessment and modeling of basic inventory parameters, namely demand, procurement cost, cycle time, ordering cost, inventory carrying cost, inventory stock, stock out level, and stock out cost. In the context of economic lot size, it provides equations related to the optimum values. It also discusses why the optimum lot size and optimum total relevant cost are considered to be key decision variables, and uses numerous examples to explain each of these inventory parameters separately. Lastly, it provides detailed information on parameter estimation for different sectors/products. Written in a simple and lucid style, it offers a valuable resource for a broad readership, especially Master of Business Administration (MBA) students.

ANALYSIS MODEL FOR INVENTORY MANAGEMENT

Directory of Open Access Journals (Sweden)

CAMELIA BURJA

2010-01-01

Full Text Available The inventory represents an essential component for the assets of the enterprise and the economic analysis gives them special importance because their accurate management determines the achievement of the activity object and the financial results. The efficient management of inventory requires ensuring an optimum level for them, which will guarantee the normal functioning of the activity with minimum inventory expenses and funds which are immobilised. The paper presents an analysis model for inventory management based on their rotation speed and the correlation with the sales volume illustrated in an adequate study. The highlighting of the influence factors on the efficient inventory management ensures the useful information needed to justify managerial decisions, which will lead to a balancedfinancial position and to increased company performance.

Inventory Data on Commercial Broiler Chicken Production System using Life Cycle Assessment Approach: A Case Study

Science.gov (United States)

Suffian, S. A.; Sidek, A. A.; Yusof, H. M.; Al-Hazza, M. H. F.

2018-01-01

An inventory analysis of the life cycle of broiler chicken production from cradle-to-gate perspective was carried out with the aim to identify possible input and output parameters involved in the system. To do so, broiler chicken production in Myra Chicken Farm and Services was investigated in detail. Result shows the inventory data on feed consumption, transportation, physical performance parameter and other utilities that affect the product which is broilers. Broilers production in fact shows escalation year by year because of high demand from consumer. A cradle-to-gate assessment was conducted based on ISO 14040/14044 guidelines. Inventory data was gathered from farmers and available literature. Improving all the input and output system will increase the level of productivity and the cost of the production. Thus, at the end of the research, it will able to make industry player to understand and take into consideration the solutions in order to promote a green broiler chicken production.

Life cycle inventory of sodium acetate and expanded graphite: Short report

Energy Technology Data Exchange (ETDEWEB)

Jungbluth, N. [ESU-Services Ltd., Uster (Switzerland); Nguyen, B. [Haute Ecole d' Ingenierie et de Gestion du canton de Vaud, Laboratoire d' Energetique Solaire et de Physique du BATiment, HEIG-VD / LESBAT, Yverdon-les-Bains (Switzerland)

2008-07-01

This short report for the Laboratory for Solar Energy and Building Physics at the University of Applied Sciences in Yverdon, Switzerland, takes a look at work being done on the issue of solar energy storage. The use of sodium acetate as a phase-change material is reviewed and considered as being a good way of optimising solar heating systems. The goal of this study was to assess if the energy gain resulting from the use of sodium acetate is balanced out or not by its embodied energy. The study investigated sodium acetate with and without expanded graphite. The paper discusses the life cycle inventory analysis of the two materials and provides some aggregated key indicators for further analysis. In general the ecoinvent methodology has been followed in order to achieve full consistency with the background data used and to provide an assessment of the materials' impact on the environment.

Inventory Control System for a Healthcare Apparel Service Centre with Stockout Risk: A Case Analysis.

Science.gov (United States)

Pan, An; Hui, Chi-Leung

2017-01-01

Based on the real-world inventory control problem of a capacitated healthcare apparel service centre in Hong Kong which provides tailor-made apparel-making services for the elderly and disabled people, this paper studies a partial backordered continuous review inventory control problem in which the product demand follows a Poisson process with a constant lead time. The system is controlled by an ( Q , r ) inventory policy which incorporate the stockout risk, storage capacity, and partial backlog. The healthcare apparel service centre, under the capacity constraint, aims to minimize the inventory cost and achieving a low stockout risk. To address this challenge, an optimization problem is constructed. A real case-based data analysis is conducted, and the result shows that the expected total cost on an order cycle is reduced substantially at around 20% with our proposed optimal inventory control policy. An extensive sensitivity analysis is conducted to generate additional insights.

Toward Automated Inventory Modeling in Life Cycle Assessment: The Utility of Semantic Data Modeling to Predict Real-WorldChemical Production

Science.gov (United States)

A set of coupled semantic data models, i.e., ontologies, are presented to advance a methodology towards automated inventory modeling of chemical manufacturing in life cycle assessment. The cradle-to-gate life cycle inventory for chemical manufacturing is a detailed collection of ...

Categorization of Used Nuclear Fuel Inventory in Support of a Comprehensive National Nuclear Fuel Cycle Strategy

International Nuclear Information System (INIS)

Wagner, John C.; Peterson, Joshua L.; Mueller, Don; Gehin, Jess C.; Worrall, Andrew; Taiwo, Temitope; Nutt, Mark; Williamson, Mark A.; Todosow, Mike; Wigeland, Roald; Halsey, William; Omberg, Ronald; Swift, Peter; Carter, Joe

2013-01-01

A technical assessment of the current inventory [∼70,150 metric tons of heavy metal (MTHM) as of 2011] of U.S.-discharged used nuclear fuel (UNF) has been performed to support decisions regarding fuel cycle strategies and research, development and demonstration (RD and D) needs. The assessment considered discharged UNF from commercial nuclear electricity generation and defense and research programs and determined that the current UNF inventory can be divided into the following three categories: 1. Disposal - excess material that is not needed for other purposes; 2. Research - material needed for RD and D purposes to support waste management (e.g., UNF storage, transportation, and disposal) and development of alternative fuel cycles (e.g., separations and advanced fuels/reactors); and 3. Recycle/Recovery - material with inherent and/or strategic value. A set of key assumptions and attributes relative to the various disposition options were used to categorize the current UNF inventory. Based on consideration of RD and D needs, time frames and material needs for deployment of alternative fuel cycles, characteristics of the current UNF inventory, and possible uses to support national security interests, it was determined that the vast majority of the current UNF inventory should be placed in the Disposal category, without the need to make fuel retrievable from disposal for reuse or research purposes. Access to the material in the Research and Recycle/Recovery categories should be retained to support RD and D needs and national security interests. This assessment does not assume any decision about future fuel cycle options or preclude any potential options, including those with potential recycling of commercial UNF.

Inventory Control System for a Healthcare Apparel Service Centre with Stockout Risk: A Case Analysis

Directory of Open Access Journals (Sweden)

An Pan

2017-01-01

Full Text Available Based on the real-world inventory control problem of a capacitated healthcare apparel service centre in Hong Kong which provides tailor-made apparel-making services for the elderly and disabled people, this paper studies a partial backordered continuous review inventory control problem in which the product demand follows a Poisson process with a constant lead time. The system is controlled by an (Q,r inventory policy which incorporate the stockout risk, storage capacity, and partial backlog. The healthcare apparel service centre, under the capacity constraint, aims to minimize the inventory cost and achieving a low stockout risk. To address this challenge, an optimization problem is constructed. A real case-based data analysis is conducted, and the result shows that the expected total cost on an order cycle is reduced substantially at around 20% with our proposed optimal inventory control policy. An extensive sensitivity analysis is conducted to generate additional insights.

Categorization of Used Nuclear Fuel Inventory in Support of a Comprehensive National Nuclear Fuel Cycle Strategy - 13575

Energy Technology Data Exchange (ETDEWEB)

Wagner, John C.; Peterson, Joshua L.; Mueller, Don E.; Gehin, Jess C.; Worrall, Andrew [Oak Ridge National Laboratory, P.O. Box 2008, Bldg. 5700, MS-6170, Oak Ridge, TN 37831 (United States); Taiwo, Temitope; Nutt, Mark; Williamson, Mark A. [Argonne National Laboratory (United States); Todosow, Mike [Brookhaven National Laboratory (United States); Wigeland, Roald [Idaho National Laboratory (United States); Halsey, William G. [Lawrence Livermore National Laboratory (United States); Omberg, Ronald P. [Pacific Northwest National Laboratory (United States); Swift, Peter N. [Sandia National Laboratories (United States); Carter, Joe [Savannah River National Laboratory (United States)

2013-07-01

A technical assessment of the current inventory [∼70,150 metric tons of heavy metal (MTHM) as of 2011] of U.S.-discharged used nuclear fuel (UNF) has been performed to support decisions regarding fuel cycle strategies and research, development and demonstration (RD and D) needs. The assessment considered discharged UNF from commercial nuclear electricity generation and defense and research programs and determined that the current UNF inventory can be divided into the following three categories: 1. Disposal - excess material that is not needed for other purposes; 2. Research - material needed for RD and D purposes to support waste management (e.g., UNF storage, transportation, and disposal) and development of alternative fuel cycles (e.g., separations and advanced fuels/reactors); and 3. Recycle/Recovery - material with inherent and/or strategic value. A set of key assumptions and attributes relative to the various disposition options were used to categorize the current UNF inventory. Based on consideration of RD and D needs, time frames and material needs for deployment of alternative fuel cycles, characteristics of the current UNF inventory, and possible uses to support national security interests, it was determined that the vast majority of the current UNF inventory should be placed in the Disposal category, without the need to make fuel retrievable from disposal for reuse or research purposes. Access to the material in the Research and Recycle/Recovery categories should be retained to support RD and D needs and national security interests. This assessment does not assume any decision about future fuel cycle options or preclude any potential options, including those with potential recycling of commercial UNF. (authors)

Categorization of Used Nuclear Fuel Inventory in Support of a Comprehensive National Nuclear Fuel Cycle Strategy - 13575

International Nuclear Information System (INIS)

Wagner, John C.; Peterson, Joshua L.; Mueller, Don E.; Gehin, Jess C.; Worrall, Andrew; Taiwo, Temitope; Nutt, Mark; Williamson, Mark A.; Todosow, Mike; Wigeland, Roald; Halsey, William G.; Omberg, Ronald P.; Swift, Peter N.; Carter, Joe

2013-01-01

A technical assessment of the current inventory [∼70,150 metric tons of heavy metal (MTHM) as of 2011] of U.S.-discharged used nuclear fuel (UNF) has been performed to support decisions regarding fuel cycle strategies and research, development and demonstration (RD and D) needs. The assessment considered discharged UNF from commercial nuclear electricity generation and defense and research programs and determined that the current UNF inventory can be divided into the following three categories: 1. Disposal - excess material that is not needed for other purposes; 2. Research - material needed for RD and D purposes to support waste management (e.g., UNF storage, transportation, and disposal) and development of alternative fuel cycles (e.g., separations and advanced fuels/reactors); and 3. Recycle/Recovery - material with inherent and/or strategic value. A set of key assumptions and attributes relative to the various disposition options were used to categorize the current UNF inventory. Based on consideration of RD and D needs, time frames and material needs for deployment of alternative fuel cycles, characteristics of the current UNF inventory, and possible uses to support national security interests, it was determined that the vast majority of the current UNF inventory should be placed in the Disposal category, without the need to make fuel retrievable from disposal for reuse or research purposes. Access to the material in the Research and Recycle/Recovery categories should be retained to support RD and D needs and national security interests. This assessment does not assume any decision about future fuel cycle options or preclude any potential options, including those with potential recycling of commercial UNF. (authors)

Preliminary design and analysis on nuclear fuel cycle for fission-fusion hybrid spent fuel burner

International Nuclear Information System (INIS)

Chen Yan; Wang Minghuang; Jiang Jieqiong

2012-01-01

A wet-processing-based fuel cycle and a dry-processing were designed for a fission-fusion hybrid spent fuel burner (FDS-SFB). Mass flow of SFB was preliminarily analyzed. The feasibility analysis of initial loaded fuel inventory, recycle fuel fabrication and spent fuel reprocessing were preliminarily evaluated. The results of mass flow of FDS-SFB demonstrated that the initial loaded fuel inventory, recycle fuel fabrication and spent fuel reprocessing of nuclear fuel cycle of FDS-SFB is preliminarily feasible. (authors)

EFO-LCI: A New Life Cycle Inventory Database of Forestry Operations in Europe

Science.gov (United States)

Cardellini, Giuseppe; Valada, Tatiana; Cornillier, Claire; Vial, Estelle; Dragoi, Marian; Goudiaby, Venceslas; Mues, Volker; Lasserre, Bruno; Gruchala, Arkadiusz; Rørstad, Per Kristian; Neumann, Mathias; Svoboda, Miroslav; Sirgmets, Risto; Näsärö, Olli-Pekka; Mohren, Frits; Achten, Wouter M. J.; Vranken, Liesbet; Muys, Bart

2018-06-01

Life cycle assessment (LCA) has become a common methodology to analyze environmental impacts of forestry systems. Although LCA has been widely applied to forestry since the 90s, the LCAs are still often based on generic Life Cycle Inventory (LCI). With the purpose of improving LCA practices in the forestry sector, we developed a European Life Cycle Inventory of Forestry Operations (EFO-LCI) and analyzed the available information to check if within the European forestry sector national differences really exist. We classified the European forests on the basis of "Forest Units" (combinations of tree species and silvicultural practices). For each Forest Unit, we constructed the LCI of their forest management practices on the basis of a questionnaire filled out by national silvicultural experts. We analyzed the data reported to evaluate how they vary over Europe and how they affect LCA results and made freely available the inventory data collected for future use. The study shows important variability in rotation length, type of regeneration, amount and assortments of wood products harvested, and machinery used due to the differences in management practices. The existing variability on these activities sensibly affect LCA results of forestry practices and raw wood production. Although it is practically unfeasible to collect site-specific data for all the LCAs involving forest-based products, the use of less generic LCI data of forestry practice is desirable to improve the reliability of the studies. With the release of EFO-LCI we made a step toward the construction of regionalized LCI for the European forestry sector.

Analysis of Korean Nuclear Fuel Cycle System by Using DANESS Code

International Nuclear Information System (INIS)

Jeong, Chang Joon

2009-08-01

Korean fast reactor scenarios have been analyzed for various kinds of conversion ratio (CR) by the DANESS system dynamic analysis code. The once-through fuel cycle analysis was modeled based on the Korean 'National Energy Basic Plan' up to 2030 and a postulated nuclear demand growth rate until 2150. The fast reactor scenario analysis has been performed for three kinds of conversion ratios such as 0.3, 0.61 and 1.0. Through the calculations, the nuclear reactor deployment scenario, front-end cycle, back-end cycle, and long-term heat load have been investigated. From the once-through results, it is shown that the nuclear power demand would be ∼70 GWe and the total amount of the spent fuel accumulated by 2150 would be ∼168000 t. The fast reactor (FR) scenario analysis results show that the spent fuel inventory and out-pile transuranic element (TRU) can be reduced by increasing the fast reactor conversion ratio. Furthermore, the long-term heat load of spent fuel decreases with increasing the conversion ratio. However, it is known that the deployment of a fast reactor of low conversion ratio does not much reduce the spent fuel and out-pile TRU inventory due to the fast reactor deployment limitation which is related to the availability of TRU

Life cycle inventory of oil palm lumber production: A gate-to-gate case study

Science.gov (United States)

Shamsudin, Noor Ainna; Sahid, Ismail; Mokhtar, Anis; Muhamad, Halimah; Ahmad, Shamim

2018-04-01

Life Cycle Assessment (LCA) has been applied in the Malaysian oil palm industry since 2010. It is important to ensure that this main industry is ready to meet the demands and expectations of European market on the environmental performance of the oil palm industry. In addition, oil palm biomass, especially oil palm trunk (OPT) are abundantly available after replanting every year. In order to maximize the usage of OPT as a green product, it can be converted to palm lumber as a value-added product. Palm lumber act as a basis product from OPT before it is converted to panel product such as plywood, sandwich board and so on. However, the LCA study on palm lumber production is still scarce in Malaysia. Hence, this paper aims to perform and collect the inventory data for palm lumber production, which is known as Life Cycle Inventory (LCI). A gate-to-gate system boundary and the functional unit of 1 m3 of palm lumber produced have been used in this study. This inventory data was collected from three batches of the production cycle. The inputs are mainly the raw materials which are the OPT and the energy from diesel and electricity from the grid. Generally, each consumption of input such as energy and fossil fuel were different at each stage of palm lumber production. Kiln-drying represents a prominent stage in terms of energy consumption, which electrical use in the dryer represents 94% of total electrical grid consumption as compared to another stage of palm lumber production. By adding the inventory information especially in the downstream sector of biomass industry, hopefully it can improve the sustainability of oil palm industry in Malaysia.

PROSES PRODUKSI BIOETANOL DARI LIMBAH CAIR GULA DALAM KAITANNYA DENGAN POTENSI SEBAGAI BAHAN BAKAR DALAM PERSPEKTIF LIFE CYCLE INVENTORY ASSESSMENT

Directory of Open Access Journals (Sweden)

Agusta Samodra Putra

2013-11-01

Full Text Available Life cycle inventory assessment merupakan salah satu tahapan di dalam Life Cycle Assessment (LCA yang bisa digunakan untuk menggambarkan interaksi materi dan energi di dalam suatu proses produksi bioetanol. Studi kasus dilakukan di pabrik gula kawasan Subang dan pabrik bioetanol di kawasan Palimanan yang merupakan pabrik gula dan bioetanol terbesar di Jawa Barat. Inventory yang dilakukan adalah pada bagian perkebunan tebu, pabrikasi tebu menjadi gula, transportasi dari pabrik gula menuju ke pabrik bioetanol, dan pabrikasi etanol. Luas lahan kebun tebu yang dimiliki oleh pabrik gula di Subang adalah seluas 5000 hektar. Dari bahan baku tebu 3000 ton/hari dihasilkan molase sebanyak 60 ton/hari, sisanya menjadi gula dan ampas tebu. Pada inventory kali ini selain dari sisi proses juga dilakukan inventory pada sisi transportasi.

Life cycle inventory and external costs of the gas fuel cycle. An overview of the main results and a brief comparison with other fuels

International Nuclear Information System (INIS)

Torfs, R.; De Nocker, L.; Wouters, G.

1999-01-01

In the context of a research project funded by the Belgian electricity utilities Electrabel/SPE, VITO made a life cycle inventory of the primary energy use and airborne emissions (including greenhouse gases, SO2 and NOx) of different fuels. Consequently, the impacts of these pollutants on human health, manmade and the natural environment are quantified and these impacts are valued in monetary terms. This analysis is based on the European ExternE methodology to estimate the external costs of energy. The LCI and external cost analysis confirm clearly that natural gas is a relative clean fossil fuel cycle. External cost are in the range of 1.2 to 2.6 EUROcent /kWh, which roughly corresponds from 30 % to 80 % of the private production costs. These results are introduced into a software module, which allows the utilities to compare economic costs and environmental benefits of different measures to reduce CO2 emissions. (author)

Rate equations modeling for hydrogen inventory studies during a real tokamak material thermal cycle

Energy Technology Data Exchange (ETDEWEB)

Bonnin, X., E-mail: xavier.bonnin@iter.org [LSPM-CNRS, Université Paris 13, Sorbonne Paris Cité, 99 avenue Jean-Baptiste Clément, F-93430 Villetaneuse (France); Hodille, E. [IRFM, CEA-Cadarache, F-13108 St-Paul-Lez-Durance (France); Ning, N. [LSPM-CNRS, Université Paris 13, Sorbonne Paris Cité, 99 avenue Jean-Baptiste Clément, F-93430 Villetaneuse (France); Sang, C. [School of Physics and Optoelectronics Technology, Dalian University of Technology, Dalian 116024 (China); Grisolia, Ch. [IRFM, CEA-Cadarache, F-13108 St-Paul-Lez-Durance (France)

2015-08-15

Prediction and control of tritium inventory in plasma-facing components (PFCs) is a critical nuclear safety issue for ITER and future fusion devices. This goal can be achieved through rate equations models as presented here. We calibrate our models with thermal desorption spectrometry results to obtain a validated set of material parameters relevant to hydrogen inventory processes in bulk tungsten. The best fits are obtained with two intrinsic trap types, deep and shallow, and an extrinsic trap created by plasma irradiation and plastic deformation of the tungsten matrix associated with blister formation. We then consider a realistic cycle of plasma discharges consisting of 400 s of plasma exposure followed by a resting period of 1000 s, repeating for several hours. This cycle is then closed by a long “overnight” period, thus providing an estimate of the amount of tritium retained in the PFCs after a full day of standard operation.

Plutonium and minor actinides management in the nuclear fuel cycle: assessing and controlling the inventory

International Nuclear Information System (INIS)

Mouney, H.

2002-01-01

The mastering of the plutonium and minor actinides inventory in the French Nuclear Cycle is based on a progressive approach from the present status, dealing with the partial reprocessing of spent fuels and the recycling of Pu in the MOX assemblies loaded in the 20 licensed PWRs. This strategy keeps the door open long-term, for example, for the eventual multi-recycling of excess Pu in dedicated new assemblies, such as APA or CORAIL in order to stabilize the Pu inventory in the fuel cycle or allow its utilization in new types of fast reactors. Presently, in the framework of 1991 law, scenario studies relying on present and/or innovative technologies are carried out in order to transmute both Pu and minor actinides, thus minimising the quantities to be for disposal. (author)

Decay profiles of β and γ for a radionuclide inventory in equilibrium cycle of a BWR type reactor

International Nuclear Information System (INIS)

Salaices, M.; Sandoval, S.; Ovando, R.

2007-01-01

Presently work the β and γ radiation decay profiles for a radionuclides inventory in equilibrium cycle of a BWR type reactor is presented. The profiles are presented in terms of decay in the activity of the total inventory as well as of the chemical groups that conform the inventory. In the obtaining of the radionuclides inventory in equilibrium cycle the ORIGEN2 code, version 1 was used, which simulates fuel burnup cycles and it calculates the evolution of the isotopic composition as a result of the burnt one, irradiation and decay of the nuclear fuel. It can be observed starting from the results that the decrease in the activity for the initial inventory and the different chemical groups that conform it is approximately proportional to the base 10 logarithm of the time for the first 24 hours of having concluded the burnt one. It can also be observed that the chemical groups that contribute in more proportion to the total activity of the inventory are the lanthanides-actinides and the transition metals, with 39% and 28%, respectively. The groups of alkaline earth metals, halogens, metalloids, noble gases and alkaline metals, contribute with percentages that go from the 8 to 5%. The groups that less they contribute to the total activity of the inventory they are the non metals and semi-metals with smaller proportions that 1%. The chemical groups that more contribute to the energy of β and γ radiation its are the transition metals and the lanthanides-actinides with a change in the order of importance at the end of the 24 hours period. The case of the halogens is of relevance for the case of the γ radiation energy due that occupying the very near third site to the dimensions of the two previous groups. Additionally, the decay in the activity for the total inventory and the groups that conform it can be simulated by means of order 6 polynomials or smaller than describe its behavior appropriately. The results presented in this work, coupled to a distribution model

Life-Cycle Inventory and Costs of Different Car Powertrains

Energy Technology Data Exchange (ETDEWEB)

Roeder, Alexander

2001-12-01

This report contains two internal reports that document the data collected for a Ph.D. thesis (Roeder, A.: Integration of Life-Cycle Assessment and Energy Planning Models for the Evaluation of Car Power trains and Fuels, Dissertation ETH 14291, Zuerich/Villigen 2001). The aim of this thesis is a comparison of different car power trains and corresponding fuels under economic and ecological aspects. Such an analysis requires, of course, large amounts of data, and data mining was actually the most time-consuming part of the thesis. However, including a detailed documentation into the thesis would have made the latter far too bulky, so we decided to compile all data documentation into a single background document: the PSI report you are just reading. This report consists of two parts: The first part contains the life-cycle inventory (LCI), while the second part compiles the economic data. The LCI is based on the work of R. Frischknecht et al. that elaborated a very detailed inventory of energy systems in Switzerland (Frischknecht et al.: Oekoinventare von Energiesystemen, 3rd ed., BEW, Bern 1996). Processes already analysed in this reference (e.g. provision of most fossil energy carriers, basic processes such as standard materials or transport processes) have not been described here unless data quality requirements made a re-evaluation necessary (e.g. production of platinum- group metaIs). Within this report, you will find a description of the methodology used, the documentation of all input data, and a discussion of results. Numeric results can be found in the Appendix of the first part. The second part (that deals with the costs) is relatively short, compared to the LCI part. This is mainly because in many cases there was no need to analyse previous steps in a fuel chain or production chain in more detail: when the costs for natural gas for a European customer are known, it is clear that part of these costs is for exploration, part for extraction, part for processing

A production inventory model with deteriorating items and shortages

Directory of Open Access Journals (Sweden)

Samanta G.P.

2004-01-01

Full Text Available A continuous production control inventory model for deteriorating items with shortages is developed. A number of structural properties of the inventory system are studied analytically. The formulae for the optimal average system cost, stock level, backlog level and production cycle time are derived when the deterioration rate is very small. Numerical examples are taken to illustrate the procedure of finding the optimal total inventory cost, stock level, backlog level and production cycle time. Sensitivity analysis is carried out to demonstrate the effects of changing parameter values on the optimal solution of the system.

An Analysis of Inventory Management of T-Shirt at Mahanagari Bandung Pisan

Directory of Open Access Journals (Sweden)

Togar M Simatupang

2012-01-01

Full Text Available Inventory management plays an important role in business activity for fulfilling the demandfrom the customer. Mahanagari Bandung Pisan, a retail company that runs its business indesigning and creating the merchandise of Bandung, currently faces a problem within itsinventory management of T-shirt, the main product of the company that contributes about 79percent of the whole total sales. The company produces a high number of inventories, butthere is still lost sales occurred. This research is aimed at reviewing and finding the rootcauses of the problems occurred within inventory management of T-shirt in MahanagariBandung Pisan, by using the concept of inventory cycle for describing the current systemimplemented by Mahanagari Bandung Pisan in planning and managing the inventory of Tshirt.From the research, there are four main problems faced by the company in managing theinventory of the T-shirt. Those problems are inaccurate forecasting, unfixed schedule inordering the T-shirt to the vendor, lateness from vendor, and the office does not know currentcondition of T-shirt’s inventory. This paper proposed some solutions for solving the problem,which are combining the intuitive prediction method with moving average model for gettingthe more accurate demand forecasting, making the timeline in controlling and producing theinventory of T-shirt, implementing periodical control system and put a clause about sanctionin the contract made by Mahanagari Bandung Pisan and the vendor and controlling thesalesperson everyday and creating the rules about inventory recording.Key words: inventory management, inventory cycle, mahanagari bandung pisan, forecasting,t-shirt

Dynamic Analysis of the Thorium Fuel Cycle in CANDU Reactors

International Nuclear Information System (INIS)

Jeong, Chang Joon; Park, Chang Je

2006-02-01

The thorium fuel recycle scenarios through the Canada deuterium uranium (CANDU) reactor have been analyzed for two types of thorium fuel: homogeneous ThO 2 UO 2 and ThO 2 UO 2 -DUPIC fuels. The recycling is performed through the dry process fuel technology which has a proliferation resistance. For the once-through fuel cycle model, the existing nuclear power plant construction plan was considered up to 2016, while the nuclear demand growth rate from the year 2016 was assumed to be 0%. After setting up the once-through fuel cycle model, the thorium fuel CANDU reactor was modeled to investigate the fuel cycle parameters. In this analysis, the spent fuel inventory as well as the amount of plutonium, minor actinides and fission products of the multiple recycling fuel cycle were estimated and compared to those of the once-through fuel cycle. From the analysis results, it was found that the closed or partially closed thorium fuel cycle can be constructed through the dry process technology. Also, it is known that both the homogeneous and heterogeneous thorium fuel cycles can reduce the SF accumulation and save the natural uranium resource compared with the once-through cycle. From the material balance view point, the heterogeneous thorium fuel cycle seems to be more feasible. It is recommended, however, the economic analysis should be performed in future

Dynamic Analysis of the Thorium Fuel Cycle in CANDU Reactors

Energy Technology Data Exchange (ETDEWEB)

Jeong, Chang Joon; Park, Chang Je

2006-02-15

The thorium fuel recycle scenarios through the Canada deuterium uranium (CANDU) reactor have been analyzed for two types of thorium fuel: homogeneous ThO{sub 2}UO{sub 2} and ThO{sub 2}UO{sub 2}-DUPIC fuels. The recycling is performed through the dry process fuel technology which has a proliferation resistance. For the once-through fuel cycle model, the existing nuclear power plant construction plan was considered up to 2016, while the nuclear demand growth rate from the year 2016 was assumed to be 0%. After setting up the once-through fuel cycle model, the thorium fuel CANDU reactor was modeled to investigate the fuel cycle parameters. In this analysis, the spent fuel inventory as well as the amount of plutonium, minor actinides and fission products of the multiple recycling fuel cycle were estimated and compared to those of the once-through fuel cycle. From the analysis results, it was found that the closed or partially closed thorium fuel cycle can be constructed through the dry process technology. Also, it is known that both the homogeneous and heterogeneous thorium fuel cycles can reduce the SF accumulation and save the natural uranium resource compared with the once-through cycle. From the material balance view point, the heterogeneous thorium fuel cycle seems to be more feasible. It is recommended, however, the economic analysis should be performed in future.

Dynamic tritium inventory of a NET/ITER fuel cycle with lithium salt solution blanket

International Nuclear Information System (INIS)

Spannagel, G.; Gierszewski, P.

1991-01-01

At the Karlsruhe Nuclear Research Center (KfK) a flexible tool is being developed to simulate the dynamics of tritium inventories. This tool can be applied to any tritium handling system, especially to the fuel cycle components of future nuclear fusion devices. This instrument of simulation will be validated in equipment to be operated at the Karlsruhe Tritium Laboratory. In this study tritium inventories in a NET/ITER type fuel cycle involving a lithium salt solution blanket are investigated. The salt solution blanket serves as an example because it offers technological properties which are attractive in modeling the process; the example does not impair the general validity of the tool. Usually, the operation strategy of complex structures will deteriorate due to failures of the subsystems involved. These failures together with the reduced availability ensuing from them will be simulated. The example of this study is restricted to reduced availabilities of two subsystems, namely the reactor and the tritium recovery system. For these subsystems the influence of statistically varying intervals of operation is considered. Strategies we selected which are representative of expected modes of operation. In the design of a fuel cycle, care will be taken that prescribed availabilities of the subsystems can be achieved; however, the description of reactor operation is a complex task since operation breaks down into several campaigns for which rules have been specified which enable determination of whether a campaign has been successful and can be stopped. Thus, it is difficult to predict the overall behavior prior to a simulation which includes stochastic elements. Using the example mentioned above the capabilities of the tool will be illustrated; besides the presentation of results of inventory simulation, the applicability of these data will be discussed. (orig.)

Life-Cycle Inventory of Manufacturing Prefinished Engineered Wood Flooring in the Eastern United States

Science.gov (United States)

Richard D. Bergman; Scott A. Bowe

2010-01-01

Building products have come under increased scrutiny because of environmental impacts from their manufacturing. However, environmental impacts of manufacturing some wood products—such as prefinished engineered wood flooring—have not been determined. This study examined prefinished engineered wood flooring in the eastern United States following the life-cycle inventory...

Life Cycle Inventory Analysis of Prospective Insect Based Feed Production in West Africa

Directory of Open Access Journals (Sweden)

Martin Roffeis

2017-09-01

Full Text Available While the concept of insect based feeds (IBFs promises great potential, especially in developing countries, the sustainability performance of IBF production remains widely underexplored. Drawing on experimental data from rearing trials in West Africa, three different insect production systems were modelled ex-ante. The generic models served as a basis to analyse and compare the process performances of different IBF production systems using Musca domestica and Hermetia illucens reared on different substrates. The results show that the input efficiency in the production of IBF is largely determined by the quality of rearing substrates, the larval development time and the employed inoculation practises, i.e., the method by which eggs or larvae are added to rearing substrates. The H. illucens system ranked highest for conversion efficiency (substrate input per IBF output, but showed substantially higher inputs in labour, fossil energy and output of wastewater. M. domestica systems operated at lower conversion efficiencies, which resulted in higher outputs of residue substrates, together with higher emissions, land requirements, built infrastructure and water. By offering full disclosure of generic inventory data, this study provides data and inspiration for prospect research and development activities and offers a reference to future life cycle assessments (LCAs on IBF.

Evaluating Indicators and Life Cycle Inventories for Processes in Early Stages of Technical Readiness

Energy Technology Data Exchange (ETDEWEB)

Tan, Eric C [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Smith, Raymond [U.S. Environmental Protection Agency (EPA); Ruiz-Mercado, Gerardo [U.S. Environmental Protection Agency (EPA)

2017-11-01

This presentation examines different methods for analyzing manufacturing processes in the early stages of technical readiness. Before developers know much detail about their processes, it is valuable to apply various assessments to evaluate their performance. One type of assessment evaluates performance indicators to describe how closely processes approach desirable objectives. Another type of assessment determines the life cycle inventories (LCI) of inputs and outputs for processes, where for a functional unit of product, the user evaluates the resources used and the releases to the environment. These results can be compared to similar processes or combined with the LCI of other processes to examine up-and down-stream chemicals. The inventory also provides a listing of the up-stream chemicals, which permits study of the whole life cycle. Performance indicators are evaluated in this presentation with the U.S. Environmental Protection Agency's GREENSCOPE (Gauging Reaction Effectiveness for ENvironmental Sustainability with a multi-Objective Process Evaluator) methodology, which evaluates processes in four areas: Environment, Energy, Economics, and Efficiency. The method develops relative scores for indicators that allow comparisons across various technologies. In this contribution, two conversion pathways for producing cellulosic ethanol from biomass, via thermochemical and biochemical routes, are studied. The information developed from the indicators and LCI can be used to inform the process design and the potential life cycle effects of up- and down-stream chemicals.

Physics Metacognition Inventory Part II: Confirmatory factor analysis and Rasch analysis

Science.gov (United States)

Taasoobshirazi, Gita; Bailey, MarLynn; Farley, John

2015-11-01

The Physics Metacognition Inventory was developed to measure physics students' metacognition for problem solving. In one of our earlier studies, an exploratory factor analysis provided evidence of preliminary construct validity, revealing six components of students' metacognition when solving physics problems including knowledge of cognition, planning, monitoring, evaluation, debugging, and information management. The college students' scores on the inventory were found to be reliable and related to students' physics motivation and physics grade. However, the results of the exploratory factor analysis indicated that the questionnaire could be revised to improve its construct validity. The goal of this study was to revise the questionnaire and establish its construct validity through a confirmatory factor analysis. In addition, a Rasch analysis was applied to the data to better understand the psychometric properties of the inventory and to further evaluate the construct validity. Results indicated that the final, revised inventory is a valid, reliable, and efficient tool for assessing student metacognition for physics problem solving.

Life cycle environmental performance of renewable building materials in the context of residential construction : phase II research report: an extension to the 2005 phase I research report. Module C, Life-cycle inventory of hardwood lumber manufacturing in the Northeast and North Central United States.

Science.gov (United States)

Richard Bergman; Scott A. Bowe

2008-01-01

The goal of this study was to find the environmental impact of hardwood lumber production through a gate-to-gate Life-Cycle Inventory (LCI) on hardwood sawmills in the northeast and northcentral (NE/NC) United States. Primary mill data was collected per CORRIM Research Guidelines (CORRIM 2001). Life-cycle analysis is beyond the scope of the study.

Inventory Analysis and Social Life Cycle Assessment of Greenhouse Gas Emissions from Waste-to-Energy Incineration in Taiwan

Directory of Open Access Journals (Sweden)

Yu-Tsang Lu

2017-10-01

Full Text Available Waste-to-energy (WtE incineration technology is widely used to solve the energy supply, greenhouse gas emissions, and waste generation problems in urban areas. In Taiwan, there are new laws and regulations that would affect greenhouse gas management of WtE incineration plants. This research aims to identify or raise key issues to be promoted for WtE incineration plants due to existing management systems and complex issues mixed with GHG, energy, and solid waste treatment. This study utilizes inventory analysis and social LCA (SLCA approach on GHG management of WtE incineration plants in Taiwan to systematically identify materiality issues to be promoted. According to the results of materiality analysis for SLCA, this study generalizes four stakeholders, nine subcategories, and their 15 inventory indicators; and concludes that, among assessment results of 15 inventory indicators, three indicators are at a high level, four at a medium level, and eight at a low level. In total, 12 materiality issues are recognized. This study suggests WtE incineration plants should consider the following materiality issues with respect to priority: a systematic database and calculation methods, the goal and criteria of the laws and regulations, technology development toward circular economy and promotion activity or opportunity for local community and organization level.

Life Cycle Inventory of Biodiesel and Petroleum Diesel for Use in an Urban Bus

Energy Technology Data Exchange (ETDEWEB)

Sheehan, John [National Renewable Energy Lab. (NREL), Golden, CO (United States); Camobreco, Vince [National Renewable Energy Lab. (NREL), Golden, CO (United States); Duffield, James [National Renewable Energy Lab. (NREL), Golden, CO (United States); Graboski, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States); Graboski, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States); Shapouri, Housein [National Renewable Energy Lab. (NREL), Golden, CO (United States)

1998-05-01

This report presents the findings from a study of the life cycle inventories (LCIs) for petroleum diesel and biodiesel. An LCI is a comprehensive quantification of all the energy and environmental flows associated with a product from “cradle to grave.” It provides information on raw materials extracted from the environment; energy resources consumed; air, water, and solid waste emissions generated.

A demand-centered, hybrid life-cycle methodology for city-scale greenhouse gas inventories.

Science.gov (United States)

Ramaswami, Anu; Hillman, Tim; Janson, Bruce; Reiner, Mark; Thomas, Gregg

2008-09-01

Greenhouse gas (GHG) accounting for individual cities is confounded by spatial scale and boundary effects that impact the allocation of regional material and energy flows. This paper develops a demand-centered, hybrid life-cycle-based methodology for conducting city-scale GHG inventories that incorporates (1) spatial allocation of surface and airline travel across colocated cities in larger metropolitan regions, and, (2) life-cycle assessment (LCA) to quantify the embodied energy of key urban materials--food, water, fuel, and concrete. The hybrid methodology enables cities to separately report the GHG impact associated with direct end-use of energy by cities (consistent with EPA and IPCC methods), as well as the impact of extra-boundary activities such as air travel and production of key urban materials (consistent with Scope 3 protocols recommended by the World Resources Institute). Application of this hybrid methodology to Denver, Colorado, yielded a more holistic GHG inventory that approaches a GHG footprint computation, with consistency of inclusions across spatial scale as well as convergence of city-scale per capita GHG emissions (approximately 25 mt CO2e/person/year) with state and national data. The method is shown to have significant policy impacts, and also demonstrates the utility of benchmarks in understanding energy use in various city sectors.

Life cycle inventory analysis of hydrogen production by the steam-reforming process: comparison between vegetable oils and fossil fuels as feedstock

International Nuclear Information System (INIS)

Marquevich, M.; Sonnemann, G.W.; Castells, F.; Montane, D.

2002-01-01

A life cycle inventory analysis has been conducted to assess the environmental load, specifically CO 2 (fossil) emissions and global warming potential (GWP), associated to the production of hydrogen by the steam reforming of hydrocarbon feedstocks (methane and naphtha) and vegetable oils (rapeseed oil, soybean oil and palm oil). Results show that the GWPs associated with the production of hydrogen by steam reforming in a 100 years time frame are 9.71 and 9.46 kg CO 2 -equivalent/kg H 2 for natural gas and naphtha, respectively. For vegetable oils, the GWP decreases to 6.42 kg CO 2 -equivalent/kg H 2 for rapeseed oil, 4.32 for palm oil and 3.30 for soybean oil. A dominance analysis determined that the part of the process that has the largest effect on the GWP is the steam reforming reaction itself for the fossil fuel-based systems, which accounts for 56.7% and 74% of the total GWP for natural gas and naphtha, respectively. This contribution is zero for vegetable oil-based systems, for which harvesting and oil production are the main sources of CO 2 -eq emissions.(author)

Life Cycle Energy Analysis of Reclaimed Water Reuse Projects in Beijing.

Science.gov (United States)

Fan, Yupeng; Guo, Erhui; Zhai, Yuanzheng; Chang, Andrew C; Qiao, Qi; Kang, Peng

2018-01-01

  To illustrate the benefits of water reuse project, the process-based life cycle analysis (LCA) could be combined with input-output LCA to evaluate the water reuse project. Energy is the only evaluation parameter used in this study. Life cycle assessment of all energy inputs (LCEA) is completed mainly by the life cycle inventory (LCI), taking into account the full life cycle including the construction, the operation, and the demolition phase of the project. Assessment of benefit from water reuse during the life cycle should focus on wastewater discharge reduction and water-saving benefits. The results of LCEA of Beijing water reuse project built in 2014 in a comprehensive way shows that the benefits obtained from the reclaimed water reuse far exceed the life cycle energy consumption. In this paper, the authors apply the LCEA model to estimate the benefits of reclaimed water reuse projects quantitatively.

Relativity concept inventory: Development, analysis, and results

Directory of Open Access Journals (Sweden)

J. S. Aslanides

2013-05-01

Full Text Available We report on a concept inventory for special relativity: the development process, data analysis methods, and results from an introductory relativity class. The Relativity Concept Inventory tests understanding of relativistic concepts. An unusual feature is confidence testing for each question. This can provide additional information; for example, high confidence correlated with incorrect answers suggests a misconception. A novel aspect of our data analysis is the use of Monte Carlo simulations to determine the significance of correlations. This approach is particularly useful for small sample sizes, such as ours. Our results show a gender bias that was not present in course assessment, similar to that reported for the Force Concept Inventory.

Mining Available Data from the United States Environmental Protection Agency to Support Rapid Life Cycle Inventory Modeling of Chemical Manufacturing

Science.gov (United States)

Demands for quick and accurate life cycle assessments create a need for methods to rapidly generate reliable life cycle inventories (LCI). Data mining is a suitable tool for this purpose, especially given the large amount of available governmental data. These data are typically a...

Methodology for systematic analysis and improvement of manufacturing unit process life cycle inventory (UPLCI) CO2PE! initiative (cooperative effort on process emissions in manufacturing). Part 2: case studies

DEFF Research Database (Denmark)

Kellens, Karel; Dewulf, Wim; Overcash, Michael

2012-01-01

industrial data and engineering calculations for energy use and material loss. This approach is illustrated by means of a case study of a drilling process.The in-depth approach, which leads to more accurate LCI data as well as the identification of potential for environmental improvements...... for environmental improvement based on the in-depth analysis of individual manufacturing unit processes. Two case studies illustrate the applicability of the methodology.......This report presents two case studies, one for both the screening approach and the in-depth approach, demonstrating the application of the life cycle assessment-oriented methodology for systematic inventory analysis of the machine tool use phase of manufacturing unit processes, which has been...

Comparative Evaluation of Biomass Power Generation Systems in China Using Hybrid Life Cycle Inventory Analysis

Science.gov (United States)

Liu, Huacai; Yin, Xiuli; Wu, Chuangzhi

2014-01-01

There has been a rapid growth in using agricultural residues as an energy source to generate electricity in China. Biomass power generation (BPG) systems may vary significantly in technology, scale, and feedstock and consequently in their performances. A comparative evaluation of five typical BPG systems has been conducted in this study through a hybrid life cycle inventory (LCI) approach. Results show that requirements of fossil energy savings, and greenhouse gas (GHG) emission reductions, as well as emission reductions of SO2 and NOx, can be best met by the BPG systems. The cofiring systems were found to behave better than the biomass-only fired system and the biomass gasification systems in terms of energy savings and GHG emission reductions. Comparing with results of conventional process-base LCI, an important aspect to note is the significant contribution of infrastructure, equipment, and maintenance of the plant, which require the input of various types of materials, fuels, services, and the consequent GHG emissions. The results demonstrate characteristics and differences of BPG systems and help identify critical opportunities for biomass power development in China. PMID:25383383

Comparative Evaluation of Biomass Power Generation Systems in China Using Hybrid Life Cycle Inventory Analysis

Directory of Open Access Journals (Sweden)

Huacai Liu

2014-01-01

Full Text Available There has been a rapid growth in using agricultural residues as an energy source to generate electricity in China. Biomass power generation (BPG systems may vary significantly in technology, scale, and feedstock and consequently in their performances. A comparative evaluation of five typical BPG systems has been conducted in this study through a hybrid life cycle inventory (LCI approach. Results show that requirements of fossil energy savings, and greenhouse gas (GHG emission reductions, as well as emission reductions of SO2 and NOx, can be best met by the BPG systems. The cofiring systems were found to behave better than the biomass-only fired system and the biomass gasification systems in terms of energy savings and GHG emission reductions. Comparing with results of conventional process-base LCI, an important aspect to note is the significant contribution of infrastructure, equipment, and maintenance of the plant, which require the input of various types of materials, fuels, services, and the consequent GHG emissions. The results demonstrate characteristics and differences of BPG systems and help identify critical opportunities for biomass power development in China.

Simplified fuel cycle tritium inventory model for systems studies -- An illustrative example with an optimized cryopump exhaust system

International Nuclear Information System (INIS)

Kuan, W.; Ho, S.K.

1995-01-01

It is desirable to incorporate safety constraints due to fuel cycle tritium inventories into tokamak reactor design optimization. An optimal scenario to minimize tritium inventories without much degradation of plasma performance can be defined for each tritium processing component. In this work, the computer code TRUFFLES is used exclusively to obtain numerical data for a simplified model to be used for systems studies. As an illustration, the cryopump plasma exhaust subsystem is examined in detail for optimization purposes. This optimization procedure will then be used to further reduce its window of operation and provide constraints on the data used for the simplified tritium inventory model

Relativity Concept Inventory: Development, Analysis, and Results

Science.gov (United States)

Aslanides, J. S.; Savage, C. M.

2013-01-01

We report on a concept inventory for special relativity: the development process, data analysis methods, and results from an introductory relativity class. The Relativity Concept Inventory tests understanding of relativistic concepts. An unusual feature is confidence testing for each question. This can provide additional information; for example,…

Change impact analysis on the life cycle carbon emissions of energy systems – The nuclear example

International Nuclear Information System (INIS)

Nian, Victor

2015-01-01

Highlights: • This paper evaluates the life cycle carbon emission of nuclear power in a scenario based approach. • It quantifies the impacts to the LCA results from the change in design parameters. • The methodology can give indications towards preferred or favorable designs. • The findings contribute to the life cycle inventories of energy systems. - Abstract: The life cycle carbon emission factor (measured by t-CO 2 /GW h) of nuclear power is much lower than those of fossil fueled power generation technologies. However, the fact of nuclear energy being a low carbon power source comes with many assumptions. These assumptions range from system and process definitions, to input–output definitions, to system boundary and cut-off criteria selections, and life cycle inventory dataset. However, there is a somewhat neglected but critical aspect – the design aspect. This refers to the impacts on the life cycle carbon emissions from the change in design parameters related to nuclear power. The design parameters identified in this paper include: (1) the uranium ore grade, (2) the critical process technologies, represented by the average initial enrichment concentration of 235 U in the reactor fuel, and (3) the size of the nuclear power reactor (measured by the generating capacity). If not properly tested, assumptions in the design aspect can lead to an erroneous estimation on the life cycle carbon emission factor of nuclear power. In this paper, a methodology is developed using the Process Chain Analysis (PCA) approach to quantify the impacts of the changes in the selected design parameters on the life cycle carbon emission factor of nuclear power. The concept of doing so broadens the scope of PCAs on energy systems from “one-off” calculation to analysis towards favorable/preferred designs. The findings from the analyses can serve as addition to the life cycle inventory database for nuclear power as well as provide indications for the sustainability of

Temporal discounting in life cycle assessment: A critical review and theoretical framework

International Nuclear Information System (INIS)

Yuan, Chris; Wang, Endong; Zhai, Qiang; Yang, Fan

2015-01-01

Temporal homogeneity of inventory data is one of the major problems in life cycle assessment (LCA). Addressing temporal homogeneity of life cycle inventory data is important in reducing the uncertainties and improving the reliability of LCA results. This paper attempts to present a critical review and discussion on the fundamental issues of temporal homogeneity in conventional LCA and propose a theoretical framework for temporal discounting in LCA. Theoretical perspectives for temporal discounting in life cycle inventory analysis are discussed first based on the key elements of a scientific mechanism for temporal discounting. Then generic procedures for performing temporal discounting in LCA is derived and proposed based on the nature of the LCA method and the identified key elements of a scientific temporal discounting method. A five-step framework is proposed and reported in details based on the technical methods and procedures needed to perform a temporal discounting in life cycle inventory analysis. Challenges and possible solutions are also identified and discussed for the technical procedure and scientific accomplishment of each step within the framework. - Highlights: • A critical review for temporal homogeneity problem of life cycle inventory data • A theoretical framework for performing temporal discounting on inventory data • Methods provided to accomplish each step of the temporal discounting framework

Greenhouse gases emissions from waste management practices using Life Cycle Inventory model.

Science.gov (United States)

Chen, Tsao-Chou; Lin, Cheng-Fang

2008-06-30

When exploring the correlation between municipal solid waste management and green house gas emission, the volume and physical composition of the waste matter must be taken into account. Due to differences in local environments and lifestyles the quantity and composition of waste often vary. This leads to differences in waste treatment methods and causes different volumes of greenhouse gases (GHGs), highlighting the need for local research. In this study the Life Cycle Inventory method was used with global warming indicator GHGs as the variables. By quantifying the data and adopting a region-based approach, this created a model of household MSWM in Taipei City, a metropolitan region in Taiwan. To allow analysis and comparison a compensatory system was then added to expand the system boundary. The results of the analysis indicated that out of all the solid waste management sub-models for a function unit, recycling was the most effective method for reducing GHG emissions while using kitchen food waste as swine feeding resulted in the most GHG emissions. As for the impact of waste collection vehicles on emissions, if the efficiency of transportation could be improved and energy consumption reduced, this will help solid waste management to achieve its goal of reducing GHG emissions.

Greenhouse gases emissions from waste management practices using Life Cycle Inventory model

International Nuclear Information System (INIS)

Chen, T.-C.; Lin, C.-F.

2008-01-01

When exploring the correlation between municipal solid waste management and green house gas emission, the volume and physical composition of the waste matter must be taken into account. Due to differences in local environments and lifestyles the quantity and composition of waste often vary. This leads to differences in waste treatment methods and causes different volumes of greenhouse gases (GHGs), highlighting the need for local research. In this study the Life Cycle Inventory method was used with global warming indicator GHGs as the variables. By quantifying the data and adopting a region-based approach, this created a model of household MSWM in Taipei City, a metropolitan region in Taiwan. To allow analysis and comparison a compensatory system was then added to expand the system boundary. The results of the analysis indicated that out of all the solid waste management sub-models for a function unit, recycling was the most effective method for reducing GHG emissions while using kitchen food waste as swine feeding resulted in the most GHG emissions. As for the impact of waste collection vehicles on emissions, if the efficiency of transportation could be improved and energy consumption reduced, this will help solid waste management to achieve its goal of reducing GHG emissions

Optimality of cycle time and inventory decisions in a two echelon inventory system with exponential price dependent demand under credit period

Science.gov (United States)

Krugon, Seelam; Nagaraju, Dega

2017-05-01

This work describes and proposes an two echelon inventory system under supply chain, where the manufacturer offers credit period to the retailer with exponential price dependent demand. The model is framed as demand is expressed as exponential function of retailer’s unit selling price. Mathematical model is framed to demonstrate the optimality of cycle time, retailer replenishment quantity, number of shipments, and total relevant cost of the supply chain. The major objective of the paper is to provide trade credit concept from the manufacturer to the retailer with exponential price dependent demand. The retailer would like to delay the payments of the manufacturer. At the first stage retailer and manufacturer expressions are expressed with the functions of ordering cost, carrying cost, transportation cost. In second stage combining of the manufacturer and retailer expressions are expressed. A MATLAB program is written to derive the optimality of cycle time, retailer replenishment quantity, number of shipments, and total relevant cost of the supply chain. From the optimality criteria derived managerial insights can be made. From the research findings, it is evident that the total cost of the supply chain is decreased with the increase in credit period under exponential price dependent demand. To analyse the influence of the model parameters, parametric analysis is also done by taking with help of numerical example.

WW LCI v2: A second-generation life cycle inventory model for chemicals discharged to wastewater systems.

Science.gov (United States)

Kalbar, Pradip P; Muñoz, Ivan; Birkved, Morten

2018-05-01

We present a second-generation wastewater treatment inventory model, WW LCI 2.0, which on many fronts represents considerable advances compared to its previous version WW LCI 1.0. WW LCI 2.0 is a novel and complete wastewater inventory model integrating WW LCI 1.0, i.e. a complete life cycle inventory, including infrastructure requirement, energy consumption and auxiliary materials applied for the treatment of wastewater and disposal of sludge and SewageLCI, i.e. fate modelling of chemicals released to the sewer. The model is expanded to account for different wastewater treatment levels, i.e. primary, secondary and tertiary treatment, independent treatment by septic tanks and also direct discharge to natural waters. Sludge disposal by means of composting is added as a new option. The model also includes a database containing statistics on wastewater treatment levels and sludge disposal patterns in 56 countries. The application of the new model is demonstrated using five chemicals assumed discharged to wastewater systems in four different countries. WW LCI 2.0 model results shows that chemicals such as diethylenetriamine penta (methylene phosphonic acid) (DTPMP) and Diclofenac, exhibit lower climate change (CC) and freshwater ecotoxicity (FET) burdens upon wastewater treatment compared to direct discharge in all country scenarios. Results for Ibuprofen and Acetaminophen (more readily degradable) show that the CC burden depends on the country-specific levels of wastewater treatment. Higher treatment levels lead to lower CC and FET burden compared to direct discharge. WW LCI 2.0 makes it possible to generate complete detailed life cycle inventories and fate analyses for chemicals released to wastewater systems. Our test of the WW LCI 2.0 model with five chemicals illustrates how the model can provide substantially different outcomes, compared to conventional wastewater inventory models, making the inventory dependent upon the atomic composition of the molecules

Effect of biogenic carbon inventory on the life cycle assessment of bioenergy: challenges to the neutrality assumption

NARCIS (Netherlands)

Wiloso, E.I.; Heijungs, R.; Huppes, G.; Fang, K.

2016-01-01

Biogenic carbon is defined as carbon contained in biomass that is accumulated during plant growth. In spite of the considerable progress towards the inventory of biogenic carbon in the life cycle assessment (LCA) of bioenergy in policy guidelines, many scientific articles tend to give no

ALLOCATING ENVIRONMENTAL BURDENS ACROSS CO-PRODUCTS TO CREATE A LIFE CYCLE INVENTORY: IS THERE A BEST WAY?

Science.gov (United States)

Allocation methodology for creating life cycle inventories is frequently addressed, discussed and debated, yet the methodology continues to be in a state of flux. ISO 14041 puts perspective on the issues but its one-size fits all framework is being challenged. It is clear that ...

Life-cycle environmental performance of renewable building materials in the context of residential construction : phase II research report : an extension to the 2005 phase I research report. Module N, Life-cycle inventory of manufacturing prefinished engineered wood flooring in the eastern United States

Science.gov (United States)

Richard D. Bergman; Scott A. Bowe

2011-01-01

This study summarizes the environmental performance of prefinished engineered wood flooring using life-cycle inventory (LCI) analysis. Using primary mill data gathered from manufacturers in the eastern United States and applying the methods found in Consortium for Research on Renewable Industrial Materials (CORRIM) Research Guidelines and International Organization of...

Texas, 2008 forest inventory and analysis factsheet

Science.gov (United States)

James Bentley

2011-01-01

This science update summarizes the findings of the first statewide annual inventory conducted by the Southern Forest Inventory and Analysis (FIA) Program in cooperation with the Texas Forest Service of the forest resource attributes in Texas. The 254 counties of Texas are consolidated into seven FIA survey units—southeast (unit 1), the northeast (unit 2), the north...

Texas, 2010 forest inventory and analysis factsheet

Science.gov (United States)

James W. Bentley

2012-01-01

This science update summarizes the findings of the statewide annual inventory conducted by the Southern Forest Inventory and Analysis (FIA) Program in cooperation with the Texas Forest Service of the forest resource attributes in Texas. The 254 counties of Texas are consolidated into seven FIA survey units – southeast (unit 1), northeast (unit 2), north central (unit 3...

78 FR 14415 - Publication of Fiscal Year 2012 Service Contract Inventory Analysis

Science.gov (United States)

2013-03-05

... DEPARTMENT OF THE TREASURY Publication of Fiscal Year 2012 Service Contract Inventory Analysis AGENCY: Departmental Offices, Treasury. ACTION: Notice of publication of Fiscal Year 2012 Service Contract Inventory: Analysis of the FY 2012 Inventory and Planned Analysis of 2013. SUMMARY: The Department...

Dynamic modeling and analysis of alternative fuel cycle scenarios in Korea

International Nuclear Information System (INIS)

Jeong, Chang Joon; Choi, Hang Bok

2007-01-01

The Korean nuclear fuel cycle was modeled by the dynamic analysis method, which was applied to the once-through and alternative fuel cycles. First, the once-through fuel cycle was analyzed based on the Korean nuclear power plant construction plan up to 2015 and a postulated nuclear demand growth rate of zero after 2015. Second, alternative fuel cycles including the direct use of spent pressurized water reactor fuel in Canada deuterium reactors (DUPIC), a sodium-cooled fast reactor and an accelerator driven system were assessed and the results were compared with those of the once-through fuel cycle. The once-through fuel cycle calculation showed that the nuclear power demand would be 25 GWe and the amount of the spent fuel will be ∼65000 tons by 2100. The alternative fuel cycle analyses showed that the spent fuel inventory could be reduced by more than 30% and 90% through the DUPIC and fast reactor fuel cycles, respectively, when compared with the once-through fuel cycle. The results of this study indicate that both spent fuel and uranium resources can be effectively managed if alternative reactor systems are timely implemented along with the existing reactors

Representativeness of environmental impact assessment methods regarding Life Cycle Inventories.

Science.gov (United States)

Esnouf, Antoine; Latrille, Éric; Steyer, Jean-Philippe; Helias, Arnaud

2018-04-15

Life Cycle Assessment (LCA) characterises all the exchanges between human driven activities and the environment, thus representing a powerful approach for tackling the environmental impact of a production system. However, LCA practitioners must still choose the appropriate Life Cycle Impact Assessment (LCIA) method to use and are expected to justify this choice: impacts should be relevant facing the concerns of the study and misrepresentations should be avoided. This work aids practitioners in evaluating the adequacy between the assessed environmental issues and studied production system. Based on a geometrical standpoint of LCA framework, Life Cycle Inventories (LCIs) and LCIA methods were localized in the vector space spanned by elementary flows. A proximity measurement, the Representativeness Index (RI), is proposed to explore the relationship between those datasets (LCIs and LCIA methods) through an angular distance. RIs highlight LCIA methods that measure issues for which the LCI can be particularly harmful. A high RI indicates a close proximity between a LCI and a LCIA method, and highlights a better representation of the elementary flows by the LCIA method. To illustrate the benefits of the proposed approach, representativeness of LCIA methods regarding four electricity mix production LCIs from the ecoinvent database are presented. RIs for 18 LCIA methods (accounting for a total of 232 impact categories) were calculated on these LCIs and the relevance of the methods are discussed. RIs prove to be a criterion for distinguishing the different LCIA methods and could thus be employed by practitioners for deeper interpretations of LCIA results. Copyright © 2017 Elsevier B.V. All rights reserved.

Analysis of environmental impact phase in the life cycle of a nuclear power plant

International Nuclear Information System (INIS)

Hernandez del M, C.

2015-01-01

The life-cycle analysis covers the environmental aspects of a product throughout its life cycle. The focus of this study was to apply a methodology of life-cycle analysis for the environmental impact assessment of a nuclear power plant by analyzing international standards ISO 14040 and 14044. The methodology of life-cycle analysis established by the ISO 14044 standard was analyzed, as well as the different impact assessment methodologies of life cycle in order to choose the most appropriate for a nuclear power plant; various tools for the life-cycle analysis were also evaluated, as is the use of software and the use of databases to feed the life cycle inventory. The functional unit chosen was 1 KWh of electricity, the scope of analysis ranging from the construction and maintenance, disposal of spent fuel to the decommissioning of the plant, the manufacturing steps of the fuel were excluded because in Mexico is not done this stage. For environmental impact assessment was chosen the Recipe methodology which evaluates up to 18 impact categories depending on the project. In the case of a nuclear power plant were considered only categories of depletion of the ozone layer, climate change, ionizing radiation and formation of particulate matter. The different tools for life-cycle analysis as the methodologies of impact assessment of life cycle, different databases or use of software have been taken according to the modeling of environmental sensitivities of different regions, because in Mexico the methodology for life-cycle analysis has not been studied and still do not have all the tools necessary for the evaluation, so the uncertainty of the data supplied and results could be higher. (Author)

Life cycle analysis of photovoltaic cell and wind power plants

International Nuclear Information System (INIS)

Uchiyama, Yohji

1997-01-01

The paper presents life cycle analyses of net energy and CO 2 emissions on photovoltaic cell and wind power generation plants. Energy requirements associated with a plant are estimated for producing materials, manufacturing equipment, constructing facilities, acid operating plants. Energy ratio and net supplied energy are calculated by the process energy analysis that examines the entire energy inventory of input and output during life time of a plant. Life cycle CO 2 emission can also be calculated from the energy requirements obtained by the net energy analysis. The emission also includes greenhouse effect equivalent to CO 2 emission of methane gas leakage at a mining as well as CO 2 emissions from fossil fuel combustion during generating electricity, natural gas treatment at an extracting well and cement production in industry. The commercially available and future-commercial technologies are dealt with in the study. Regarding PV technologies, two different kinds of installation are investigated; roof-top typed installation of residential houses and ground installation of electric utilities. (author)

East Texas, 2011 forest inventory and analysis factsheet

Science.gov (United States)

Jason A. Cooper; James W. Bentley

2012-01-01

This science update summarizes the findings of the annual inventory conducted by the Southern Forest Inventory and Analysis (FIA) Program in cooperation with the Texas Forest Service of the forest resource attributes in east Texas. The 254 counties of Texas are consolidated into 7 FIA survey units—southeast (unit 1), northeast (unit 2), north central (unit 3), south (...

Life cycle impact assessment (LCIA) using the ecological scarcity ...

African Journals Online (AJOL)

After it is done, the inventory will be interpreted to the environmental impacts in life cycle impact assessment (LCIA). Two LCIA methods identified were “midpoint and endpoint” approaches. The ecological scarcity (ecopoints) is an LCIA method using “midpoint” approach. From the analysis to both life cycle stages, analysis ...

Life-cycle assessment of biodiesel versus petroleum diesel fuel

International Nuclear Information System (INIS)

Coulon, R.; Camobreco, V.; Sheehan, J.; Duffield, J.

1995-01-01

The US Department of Energy's Office of Transportation Technologies, DOE's National Renewable Energy Laboratory, the US Department of Agriculture's Office of Energy, and Ecobalance are carrying out a comprehensive Life-Cycle Assessment of soy-based diesel fuel (biodiesel) to quantify the environmental aspects of the cradle-to-grave production and use of biodiesel. The purpose of the project is to produce an analytical tool and database for use by industry and government decision makers involved in alternative fuel use and production. The study also includes a parallel effort to develop a life-cycle model for petroleum diesel fuel. The two models are used to compare the life-cycle energy and environmental implications of petroleum diesel and biodiesel derived from soybean. Several scenarios are studied, analyzing the influence of transportation distances, agricultural practice and allocation rules used. The project also includes effort to integrate spatial data into the inventory analysis and probabilistic uncertainty considerations into the impact assessment stage. Traditional life-cycle inventory analysis includes an aggregation process that eliminates spatial, temporal, and threshold information. This project will demonstrate an approach to life-cycle inventory analysis that retains spatial data for use in impact assessment. Explicit probabilistic treatment of uncertainty in impact assessment will take account of scientific uncertainties, and will attempt to identify the level of spatial detail that most efficiently reduces impact assessment uncertainties

Greenhouse gas emission inventory based on full energy chain analysis

International Nuclear Information System (INIS)

Dones, R.; Hirschberg, S.; Knoepfel, I.

1996-01-01

Methodology, characteristics, features and results obtained for greenhouse gases within the recent Swiss LCA study 'Environmental Life-Cycle Inventories of Energy Systems' are presented. The focus of the study is on existing average Full Energy Chains (FENCHs) in the electricity generation mixes in Europe and in Switzerland. The systems, including coal (hard coal and lignite), oil, natural gas, nuclear and hydro, are discussed one by one as well as part of the electricity mixes. Photovoltaic systems are covered separately since they are not included in the electricity mixes. A sensitivity analysis on methane leakage during long-range transport via pipeline is shown. Whilst within the current study emissions are not attributed to specific countries, the main sectors contributing to the total GHGs emissions calculated for the various FENCHs are specified. (author). 10 refs, 10 figs, 9 tabs

Greenhouse gas emission inventory based on full energy chain analysis

Energy Technology Data Exchange (ETDEWEB)

Dones, R; Hirschberg, S [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Knoepfel, I [Federal Inst. of Technology Zurich, Zurich (Switzerland)

1996-07-01

Methodology, characteristics, features and results obtained for greenhouse gases within the recent Swiss LCA study `Environmental Life-Cycle Inventories of Energy Systems` are presented. The focus of the study is on existing average Full Energy Chains (FENCHs) in the electricity generation mixes in Europe and in Switzerland. The systems, including coal (hard coal and lignite), oil, natural gas, nuclear and hydro, are discussed one by one as well as part of the electricity mixes. Photovoltaic systems are covered separately since they are not included in the electricity mixes. A sensitivity analysis on methane leakage during long-range transport via pipeline is shown. Whilst within the current study emissions are not attributed to specific countries, the main sectors contributing to the total GHGs emissions calculated for the various FENCHs are specified. (author). 10 refs, 10 figs, 9 tabs.

ORIGEN2.1 Cycle Specific Calculation of Krsko Nuclear Power Plant Decay Heat and Core Inventory

International Nuclear Information System (INIS)

Vukovic, J.; Grgic, D.; Konjarek, D.

2010-01-01

This paper presents ORIGEN2.1 computer code calculation of Krsko Nuclear Power Plant core for Cycle 24. The isotopic inventory, core activity and decay heat are calculated in one run for the entire core using explicit depletion and decay of each fuel assembly. Separate pre-ori application which was developed is utilized to prepare corresponding ORIGEN2.1 inputs. This application uses information on core loading pattern to determine fuel assembly specific depletion history using 3D burnup which is obtained from related PARCS computer code calculation. That way both detailed single assembly calculations as well as whole core inventory calculations are possible. Because of the immense output of the ORIGEN2.1, another application called post-ori is used to retrieve and plot any calculated property on the basis of nuclide, element, summary isotope or group of elements for activation products, actinides and fission products segments. As one additional possibility, with the post-ori application it is able to calculate radiotoxicity from calculated ORIGEN2.1 inventory. The results which are obtained using the calculation model of ORIGEN2.1 computer code are successfully compared against corresponding ORIGEN-S computer code results.(author).

Life cycle inventory analysis of regenerative thermal oxidation of air emissions from oriented strand board facilities in Minnesota - a perspective of global climate change

Energy Technology Data Exchange (ETDEWEB)

Nicholson, W.J. [Potlatch Corp., San Francisco, CA (United States)

1997-12-31

Life cycle inventory analysis has been applied to the prospective operation of regenerative thermal oxidation (RTO) technology at oriented strand board plants at Bemidji (Line 1) and Cook, Minnesota. The net system destruction of VOC`s and carbon monoxide, and at Cook a small quantity of particulate, has a very high environmental price in terms of energy and water use, global warming potential, sulfur and nitrogen oxide emissions, solids discharged to water, and solid waste deposited in landfills. The benefit of VOC destruction is identified as minor in terms of ground level ozone at best and possibly slightly detrimental. Recognition of environmental tradeoffs associated with proposed system changes is critical to sound decision-making. There are more conventional ways to address carbon monoxide emissions than combustion in RTO`s. In an environment in which global warming is a concern, fuel supplemental combustion for environmental control does not appear warranted. Consideration of non-combustion approaches to address air emission issues at the two operations is recommended. 1 ref., 5 tabs.

The Structure of the S-R Inventory of Anxiousness: Further Analysis.

Science.gov (United States)

Birenbaum, Menucha; And Others

1986-01-01

The Endler S-R Inventory of General Trait Anxiousness was analyzed employing Smallest Space Analysis (SSA) and factor analysis. The SSA yielded a two-dimensional lattice partitioning the space into regions corresponding to the situations specified in the inventory. The factor-analytic results were similar but not as informative. (Author/JAZ)

East Texas, 2012—Forest Inventory and Analysis Factsheet

Science.gov (United States)

Thomas J. Brandeis; Jason A. Cooper; James W. Bentley

2014-01-01

This science update summarizes the findings of the statewide annual inventory of the forest resource attributes in Texas conducted by the Southern Forest Inventory and Analysis (FIA) Program in cooperation with the Texas A&M Forest Service. The 254 counties of Texas are consolidated into seven FIA survey units—southeast (unit 1), northeast (unit 2), north central (...

Life cycle inventory and mass-balance of municipal food waste management systems: Decision support methods beyond the waste hierarchy.

Science.gov (United States)

Edwards, Joel; Othman, Maazuza; Crossin, Enda; Burn, Stewart

2017-11-01

When assessing the environmental and human health impact of a municipal food waste (FW) management system waste managers typically rely on the principles of the waste hierarchy; using metrics such as the mass or rate of waste that is 'prepared for recycling,' 'recovered for energy,' or 'sent to landfill.' These metrics measure the collection and sorting efficiency of a waste system but are incapable of determining the efficiency of a system to turn waste into a valuable resource. In this study a life cycle approach was employed using a system boundary that includes the entire waste service provision from collection to safe end-use or disposal. A life cycle inventory of seven waste management systems was calculated, including the first service wide inventory of FW management through kitchen in-sink disposal (food waste disposer). Results describe the mass, energy and water balance of each system along with key emissions profile. It was demonstrated that the energy balance can differ significantly from its' energy generation, exemplified by mechanical biological treatment, which was the best system for generating energy from waste but only 5 th best for net-energy generation. Furthermore, the energy balance of kitchen in-sink disposal was shown to be reduced because 31% of volatile solids were lost in pre-treatment. The study also confirmed that higher FW landfill diversion rates were critical for reducing many harmful emissions to air and water. Although, mass-balance analysis showed that the alternative end-use of the FW material may still contain high impact pollutants. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Overlooked runaway feedback in the marine nitrogen cycle: the vicious cycle

Directory of Open Access Journals (Sweden)

A. Landolfi

2013-03-01

Full Text Available The marine nitrogen (N inventory is thought to be stabilized by negative feedback mechanisms that reduce N inventory excursions relative to the more slowly overturning phosphorus inventory. Using a global biogeochemical ocean circulation model we show that negative feedbacks stabilizing the N inventory cannot persist if a close spatial association of N2 fixation and denitrification occurs. In our idealized model experiments, nitrogen deficient waters, generated by denitrification, stimulate local N2 fixation activity. But, because of stoichiometric constraints, the denitrification of newly fixed nitrogen leads to a net loss of N. This can enhance the N deficit, thereby triggering additional fixation in a vicious cycle, ultimately leading to a runaway N loss. To break this vicious cycle, and allow for stabilizing negative feedbacks to occur, inputs of new N need to be spatially decoupled from denitrification. Our idealized model experiments suggest that factors such as iron limitation or dissolved organic matter cycling can promote such decoupling and allow for negative feedbacks that stabilize the N inventory. Conversely, close spatial co-location of N2 fixation and denitrification could lead to net N loss.

TIARA analysis of tritium inventory in Li2O

International Nuclear Information System (INIS)

Billone, M.C.

1995-01-01

The TIARA code has been developed to predict tritium inventory in Li 2 O breeder ceramic and to predict purge exit flow rate and composition under steady-state operating conditions. Inventory predictions are based on models for bulk diffusion, surface desorption, solubility and precipitation. Parameters for these models are determined from the results of laboratory annealing studies on unirradiated and irradiated Li 2 O and from a limited number (2) of inventory data measured after in-reactor purge flow testing. The remaining inventory data points (18) are used for code validation. In the validation exercise, models and model parameters are fixed prior to running the validation cases to assess how well TIARA predictions agree with data. On average, the TIARA predictions are in excellent agreement with the inventory data from the following in-reactor tests: EXOTIC-2, SIBELIUS, VOM-15H, CRITIC-1, BEATRIX-II (Phase 1) thin ring, and BEATRIX-II (Phase 1) thick pellet. Thus, TIARA can be used with a reasonable degree of confidence for design analysis over a broad range of fabrication variables and steady-state operating conditions. (orig.)

ITER Dynamic Tritium Inventory Modeling Code

International Nuclear Information System (INIS)

Cristescu, Ioana-R.; Doerr, L.; Busigin, A.; Murdoch, D.

2005-01-01

A tool for tritium inventory evaluation within each sub-system of the Fuel Cycle of ITER is vital, with respect to both the process of licensing ITER and also for operation. It is very likely that measurements of total tritium inventories may not be possible for all sub-systems, however tritium accounting may be achieved by modeling its hold-up within each sub-system and by validating these models in real-time against the monitored flows and tritium streams between the systems. To get reliable results, an accurate dynamic modeling of the tritium content in each sub-system is necessary. In order to optimize the configuration and operation of the ITER fuel cycle, a dynamic fuel cycle model was developed progressively in the decade up to 2000-2001. As the design for some sub-systems from the fuel cycle (i.e. Vacuum pumping, Neutral Beam Injectors (NBI)) have substantially progressed meanwhile, a new code developed under a different platform to incorporate these modifications has been developed. The new code is taking over the models and algorithms for some subsystems, such as Isotope Separation System (ISS); where simplified models have been previously considered, more detailed have been introduced, as for the Water Detritiation System (WDS). To reflect all these changes, the new code developed inside EU participating team was nominated TRIMO (Tritium Inventory Modeling), to emphasize the use of the code on assessing the tritium inventory within ITER

Combined methodology of optimization and life cycle inventory for a biomass gasification based BCHP system

International Nuclear Information System (INIS)

Wang, Jiang-Jiang; Yang, Kun; Xu, Zi-Long; Fu, Chao; Li, Li; Zhou, Zun-Kai

2014-01-01

Biomass gasification based building cooling, heating, and power (BCHP) system is an effective distributed energy system to improve the utilization of biomass resources. This paper proposes a combined methodology of optimization method and life cycle inventory (LCI) for the biomass gasification based BCHP system. The life cycle models including biomass planting, biomass collection-storage-transportation, BCHP plant construction and operation, and BCHP plant demolition and recycle, are constructed to obtain economic cost, energy consumption and CO 2 emission in the whole service-life. Then, the optimization model for the biomass BCHP system including variables, objective function and solution method are presented. Finally, a biomass BCHP case in Harbin, China, is optimized under different optimization objectives, the life-cycle performances including cost, energy and CO 2 emission are obtained and the grey incidence approach is employed to evaluate their comprehensive performances of the biomass BCHP schemes. The results indicate that the life-cycle cost, energy efficiency and CO 2 emission of the biomass BCHP system are about 41.9 $ MWh −1 , 41% and 59.60 kg MWh −1 respectively. The optimized biomass BCHP configuration to minimize the life-cycle cost is the best scheme to achieve comprehensive benefit including cost, energy consumption, renewable energy ratio, steel consumption, and CO 2 emission. - Highlights: • Propose the combined method of optimization and LCI for biomass BCHP system. • Optimize the biomass BCHP system to minimize the life-cycle cost, energy and emission. • Obtain the optimized life-cycle cost, energy efficiency and CO 2 emission. • Select the best biomass BCHP scheme using grey incidence approach

A case study by life cycle assessment

Science.gov (United States)

Li, Shuyun

2017-05-01

This article aims to assess the potential environmental impact of an electrical grinder during its life cycle. The Life Cycle Inventory Analysis was conducted based on the Simplified Life Cycle Assessment (SLCA) Drivers that calculated from the Valuation of Social Cost and Simplified Life Cycle Assessment Model (VSSM). The detailed results for LCI can be found under Appendix II. The Life Cycle Impact Assessment was performed based on Eco-indicator 99 method. The analysis results indicated that the major contributor to the environmental impact as it accounts for over 60% overall SLCA output. In which, 60% of the emission resulted from the logistic required for the maintenance activities. This was measured by conducting the hotspot analysis. After performing sensitivity analysis, it is evidenced that changing fuel type results in significant decrease environmental footprint. The environmental benefit can also be seen from the negative output values of the recycling activities. By conducting Life Cycle Assessment analysis, the potential environmental impact of the electrical grinder was investigated.

Inventory difference analysis at Los Alamos Plutonium Facility

International Nuclear Information System (INIS)

Zardecki, A.; Armstrong, J.M.; Longmire, V.; Strittmatter, R.B.

1997-01-01

The authors have developed a prototype computer program that reads directly the inventory entries from a Microsoft Access data base. Based on historical data, the program then displays temporal trends and constructs a library of rules that encapsulates the system behavior. The following analysis of inventory data is illustrated by using a combination of realistic and simulated facility examples. Potential payoffs of this methodology include a reduction in time and resources needed to perform statistical tests and broad applicability to Department of Energy needs--for example, treaty verification

Life cycle inventory of manufacturing prefinished engineered wood flooring in eastern U.S. with comparison to solid strip wood flooring

Science.gov (United States)

Richard D. Bergman; Scott A. Bowe

2011-01-01

Building products have come under increased scrutiny because of environmental impacts from their manufacture. Our study followed the life cycle inventory approach for prefinished engineered wood flooring in the eastern US and compared the results with those of solid strip wood flooring. Our study surveyed five engineered wood flooring manufacturers in the eastern US....

The benefits of life cycle inventory parametric models in streamlining data collection. A case study in the wooden pallet sector

DEFF Research Database (Denmark)

Niero, Monia; Di Felice, F.; Ren, J.

2014-01-01

LCA methodology is time and resource consuming particularly when it comes to data collection and handling, therefore companies, particularly Small and Medium Enterprises (SMEs), are inclined to use streamlined approaches to shorten the resource-consuming life cycle inventory (LCI) phase. An effec......LCA methodology is time and resource consuming particularly when it comes to data collection and handling, therefore companies, particularly Small and Medium Enterprises (SMEs), are inclined to use streamlined approaches to shorten the resource-consuming life cycle inventory (LCI) phase...... study of a SME in the wooden pallet sector, investigating to what extent the use of parametric LCI models can be beneficial both in evaluating the environmental impacts of similar products and in providing a preliminary assessment of the potential environmental impacts of new products. We developed...... an LCI parametric model describing the LCI of a range of wooden pallets and tested its effectiveness with a reference product, namely a non-reversible pallet with four-way blocks. The identified parameters refer to the technical characteristics of the product system, e.g. the number and dimension...

Tritium accountancy and unmeasurable inventories in fusion reactors

International Nuclear Information System (INIS)

Avenhaus, R.; Spannagel, G.

1997-12-01

For the time being fusion technology development involves relatively small quantities of tritium. Consequently, it is sufficient to apply so-called ''conventional'' accountancy tools. However, it is foreseeable that tritium operations - and thus the amount of tritium - will increase substantially. An advanced accountancy methodology will satisfy the resulting new requirements. In this study such an advanced accountancy methodolody is developed and applied to the situation envisaged with idealized experiments of the Karlsruhe Tritium Laboratory (TLK) as well as an idealized ITER-type fuel cycle. Firstly, this task comprises modeling of fuel cycle operations, providing the ''true'' data of the in-process inventories. As both the fuel cycle subsystems and networking themselves are susceptible to changes, a measurement model takes care of the true data, handles data reduction, and applies mathematical methods to confirm the final inventories on a statistical basis. Then, in a third step, the test statistics might verify whether or not a tritium anomaly, e.g. a tritium loss has occurred. Since the statistical analysis generates problems the solutions of which are not part of the standard statistical literature in the Annex the results of the related original work is presented in mathematical-abstract form. (orig.)

LIFE CYCLE DESIGN OF AIR INTAKE MANIFOLDS; PHASE I: 2.0 L FORD CONTOUR AIR INTAKE MANIFOLD

Science.gov (United States)

The project team applied the life cycle design methodology to the design analysis of three alternative air intake manifolds: a sand cast aluminum, brazed aluminum tubular, and nylon composite. The design analysis included a life cycle inventory analysis, environmental regulatory...

Life cycle inventory for palm based plywood: A gate-to-gate case study

Science.gov (United States)

Ahmad, Shamim; Sahid, Ismail; Subramaniam, Vijaya; Muhamad, Halimah; Mokhtar, Anis

2013-11-01

The oil palm industry heavily relies on the world market. It is essential to ensure that the oil palm industry is ready to meet the demands and expectation of these overseas customers on the environmental performance of the oil palm industry. Malaysia produces 13.9 million tons of oil palm biomass including oil palm trunk (OPT), frond and empty fruits bunches (EFB) annually. OPT felled in some oil palm plantations during replanting is transported to various industries and one such industry is the plywood factories. In order to gauge the environmental performance of the use of OPT as plywood a Life Cycle Assessment (LCA) study was conducted for palm based plywood. LCA is an important tool to assess the environmental performance of a product or process. Life cycle inventory (LCI) is the heart of a LCA study. This LCI study has a gate-to-gate system boundary and the functional unit is 1 m3 palm plywood produced and covers three types of plywood; Moisture Resistance Plywood (MR), Weather Boiling Proof Plywood Grade 1 (WBP Grade 1) at Factory D and Weather Boiling Proof Plywood Grade 2 (WBP Grade 2) at Factory E. Both factories use two different types of drying processes; conventional drying at Factory D and kiln drying at Factory E. This inventory data was collected from two factories (D and E) representing 40% of Malaysia palm plywood industry. The inputs are mainly the raw materials which are the oil palm trunks and tropical wood veneers and the energy from diesel and electricity from grid which is mainly used for the drying process. The other inputs include water, urea formaldehyde, phenol formaldehyde, flour and melamine powder. The outputs are the biomass waste which consists of oil palm trunk off-cut and emission from boiler. Generally, all types of plywood production use almost same materials and processing methods in different quantities. Due to the different process efficiency, Factory D uses less input of raw materials and energy compared to Factory E.

A factor analysis of the Kirton Adaption-Innovation Inventory using an alcoholic population.

Science.gov (United States)

Robertson, E D; Fournet, G P; Zelhart, P F; Estes, R E

1988-04-01

The present study reports a factor analysis of the Kirton Adaption-Innovation Inventory using 103 alcoholic men. Kirton in 1976 and we in an unpublished work in 1986 noted identical factor structures when responses from nonalcoholic populations to the inventory were factor analyzed. Recent reviews regarding personality characteristics of alcoholics suggest characteristics similar to the adaption-innovation concepts of Kirton. This factor analysis for an alcoholic sample supports the validity of the inventory as a measure of problem-solving style of alcoholics.

Anomaly detection for analysis of annual inventory data: a quality control approach

Science.gov (United States)

Francis A. Roesch; Paul C. Van Deusen

2010-01-01

Annual forest inventories present special challenges and opportunities for those analyzing the data arising from them. Here, we address one question currently being asked by analysts of the US Forest Service’s Forest Inventory and Analysis Program’s quickly accumulating annual inventory data. The question is simple but profound: When combining the next year’s data for...

The role of inventory management in Canadian economic fluctuations

OpenAIRE

Hung-Hay Lau

1996-01-01

Swings in inventory investment have traditionally played a major role in Canadian business cycles. However, advances in inventory-control techniques and the reduced uncertainty associated with lower inflation have enabled firms to manage their inventories much more tightly and effectively. This article examines recent developments in the management of non-farm business inventories in Canada at both the aggregate and the sectoral level and looks at implications for the role of inventories as a...

Nuclear fuel cycle system analysis

International Nuclear Information System (INIS)

Ko, W. I.; Kwon, E. H.; Kim, S. G.; Park, B. H.; Song, K. C.; Song, D. Y.; Lee, H. H.; Chang, H. L.; Jeong, C. J.

2012-04-01

The nuclear fuel cycle system analysis method has been designed and established for an integrated nuclear fuel cycle system assessment by analyzing various methodologies. The economics, PR(Proliferation Resistance) and environmental impact evaluation of the fuel cycle system were performed using improved DB, and finally the best fuel cycle option which is applicable in Korea was derived. In addition, this research is helped to increase the national credibility and transparency for PR with developing and fulfilling PR enhancement program. The detailed contents of the work are as follows: 1)Establish and improve the DB for nuclear fuel cycle system analysis 2)Development of the analysis model for nuclear fuel cycle 3)Preliminary study for nuclear fuel cycle analysis 4)Development of overall evaluation model of nuclear fuel cycle system 5)Overall evaluation of nuclear fuel cycle system 6)Evaluate the PR for nuclear fuel cycle system and derive the enhancement method 7)Derive and fulfill of nuclear transparency enhancement method The optimum fuel cycle option which is economical and applicable to domestic situation was derived in this research. It would be a basis for establishment of the long-term strategy for nuclear fuel cycle. This work contributes for guaranteeing the technical, economical validity of the optimal fuel cycle option. Deriving and fulfillment of the method for enhancing nuclear transparency will also contribute to renewing the ROK-U.S Atomic Energy Agreement in 2014

Biogas from Marine Macroalgae: a New Environmental Technology — Life Cycle Inventory for a Further LCA

Science.gov (United States)

Romagnoli, Francesco; Blumberga, Dagnija; Gigli, Emanuele

2010-01-01

The main goal of this paper is to analyze the innovative process of production of biogas (via fermentation processes) using marine macroalgae as feedstock in a pilot project plant in Augusta (Sicily, Italy). Algae, during their growth, have the capacity to assimilate nutrients and thus subsequent harvesting of the algal biomass recovers the nutrients from biowaste sources giving the possibility to transform negative environmental externalities in positive mainly in terms of eutrophication and climate change impact categories. The paper presents a novel environmental technology for the production of biogas and 2nd generation biofuel (liquid biomethane) after an upgrading process through the use of a cryogenic technology. The paper would also like to make the first attempt at understanding the possibility to implement this innovative technology in the Latvian context. The first calculations and assumptions for the Life Cycle Inventory for a further Life Cycle Assessment are presented.

TIARA analysis of tritium inventory in Li{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Billone, M.C.

1994-05-01

The TIARA code has been developed to predict tritium inventory in Li{sub 2}O breeder ceramic and to predict purge exit flow rate and composition under steady-state operating conditions. Inventory predictions are based on models for bulk diffusion, surface desorption, solubility and precipitation. Parameters for these models are determined from the results of laboratory annealing studies on unirradiated and irradiated Li{sub 2}O and from a limited number (2) of inventory data measured after in-reactor purge-flow testing. The remaining inventory data points (18) are used for code validation. In the validation exercise, models and model parameters are fixed to assess how well TIARA predictions agree with data. On the average, the TIARA predictions are in excellent agreement with the inventory data from the following in-reactor tests: EXOTIC-2, SIBELIUS, VOM-15H, CRITIC-1, BEATRIX-II (Phase 1) thin ring, and BEATRIX-II (Phase 1) thick pellet. Thus, TIARA can be used with a reasonable degree of confidence for design analysis over a broad range of fabrication variables and steady-state operating conditions.

Preliminary Investigation on Life Cycle Inventory of Powder Bed Fusion of Stainless Steel

Science.gov (United States)

Nyamekye, Patricia; Piili, Heidi; Leino, Maija; Salminen, Antti

Manufacturing of work pieces from stainless steel with laser additive manufacturing, known also as laser sintering or 3D printing may increase energy and material efficiency. The use of powder bed fusion offers advantages to make parts for dynamic applications of light weight and near-net-shape products. Due to these advantages among others, PBF may also reduce emissions and operational cost in various applications. However, there are only few life cycle assessment studies examining this subject despite its prospect to business opportunity. The application of Life Cycle Inventory (LCI) in Powder Bed Fusion (PBF) provides a distinct evaluation of material and energy consumption. LCI offers a possibility to improve knowledge of process efficiency. This study investigates effect of process sustainability in terms of raw material, energy and time consumption with PBF and CNC machining. The results of the experimental study indicated lower energy efficiency in the production process with PBF. This study revealed that specific energy consumption in PBF decreased when several components are built simultaneously than if they would be built individually. This is due to fact that energy consumption per part is lower. On the contrary, amount of energy needed to machine on part in case of CNC machining is lower when parts are done separately.

How physical modelling can improve Life Cycle Inventory accuracy and allow predictive LCA: an application to the steel industry

International Nuclear Information System (INIS)

Mirgaux, O.; Ablitzer, D.; Iosif, A.M.

2009-01-01

Assessing traditional iron and steelmaking processes from an environmental point of view and developing breakthrough eco-efficient processes for the future are major challenges for the steel industry today. In the framework of the challenging European project ULCOS, which stands for Ultra Low CO 2 Steelmaking, Life Cycle Assessment (LCA) was chosen to assess breakthrough processes that could be part of the future iron and steel making landscape and to compare them to the reference classical integrated steel-mill. To carry out such a study we propose a new methodological concept which combines LCA thinking with physicochemical process modelling. Physicochemical models were developed for each processes of the classical integrated steelmaking route in order to generate the data required to draw the Life Cycle Inventory of the route. Such a method bypasses the traditional data collection and brings accuracy to the inventory by introducing rigorous mass and energy balances into the methodology. In addition it was shown that such an approach allows testing and assessing different operational practices of the processes in order to optimise the use of energy and the CO 2 emissions, which showed that it can be used as a powerful tool for eco-conception of processes. (authors)

Integrated waste management and the tool of life cycle inventory : a route to sustainable waste management

Energy Technology Data Exchange (ETDEWEB)

McDougall, F.R.; White, P.R. [Procter and Gamble Newcastle Technical Centre, Newcastle (United Kingdom). Corporate Sustainable Development

2000-07-01

An overall approach to municipal waste management which integrates sustainable development principles was discussed. The three elements of sustainability which have to be balanced are environmental effectiveness, economic affordability and social acceptability. An integrated waste management (IWM) system considers different treatment options and deals with the entire waste stream. A life cycle inventory (LCI) and life cycle assessment (LCA) is used to determine the environmental burdens associated with IWM systems. LCIs for waste management are currently available for use in Europe, the United States, Canada and elsewhere. LCI is being used by waste management companies to assess the environmental attributes of future contract tenders. The models are used as benchmarking tools to assess the current environmental profile of a waste management system. They are also a comparative planning and communication tool. The authors are currently looking into publishing, at a future date, the experience of users of this LCI environmental management tool. 12 refs., 3 figs.

Canonical correlation analysis of the career attitudes and strategies inventory and the adult career concerns inventory

Directory of Open Access Journals (Sweden)

Charlene C Lew

2006-04-01

Full Text Available This study investigated the relationships between the scales of the Adult Career Concerns Inventory (ACCI and those of the Career Attitudes and Strategies Inventory (CASI. The scores of 202 South African adults for the two inventories were subjected to a canonical correlation analysis. Two canonical variates made statistically significant contributions to the explanation of the relationships between the two sets of variables. Inspection of the correlations of the original variables with the first canonical variate suggested that a high level of career concerns in general, as measured by the ACCI, is associated with high levels of career worries, more geographical barriers, a low risk-taking style and a non-dominant interpersonal style, as measured by the CASI. The second canonical variate suggested that concerns with career exploration and advancement of one’s career is associated with low job satisfaction, low family commitment, high work involvement, and a dominant style at work.

Multiparameter Cell Cycle Analysis.

Science.gov (United States)

Jacobberger, James W; Sramkoski, R Michael; Stefan, Tammy; Woost, Philip G

2018-01-01

Cell cycle cytometry and analysis are essential tools for studying cells of model organisms and natural populations (e.g., bone marrow). Methods have not changed much for many years. The simplest and most common protocol is DNA content analysis, which is extensively published and reviewed. The next most common protocol, 5-bromo-2-deoxyuridine S phase labeling detected by specific antibodies, is also well published and reviewed. More recently, S phase labeling using 5'-ethynyl-2'-deoxyuridine incorporation and a chemical reaction to label substituted DNA has been established as a basic, reliable protocol. Multiple antibody labeling to detect epitopes on cell cycle regulated proteins, which is what this chapter is about, is the most complex of these cytometric cell cycle assays, requiring knowledge of the chemistry of fixation, the biochemistry of antibody-antigen reactions, and spectral compensation. However, because this knowledge is relatively well presented methodologically in many papers and reviews, this chapter will present a minimal Methods section for one mammalian cell type and an extended Notes section, focusing on aspects that are problematic or not well described in the literature. Most of the presented work involves how to segment the data to produce a complete, progressive, and compartmentalized cell cycle analysis from early G1 to late mitosis (telophase). A more recent development, using fluorescent proteins fused with proteins or peptides that are degraded by ubiquitination during specific periods of the cell cycle, termed "Fucci" (fluorescent, ubiquitination-based cell cycle indicators) provide an analysis similar in concept to multiple antibody labeling, except in this case cells can be analyzed while living and transgenic organisms can be created to perform cell cycle analysis ex or in vivo (Sakaue-Sawano et al., Cell 132:487-498, 2007). This technology will not be discussed.

A comparative study of the safety and economics of fusion fuel cycles

International Nuclear Information System (INIS)

Brereton, S.J.; Kazimi, M.S.

1988-01-01

The safety and economic characteristics of the deuterium-tritium (DT), deuterium-deuterium (DD) and deuterium-helium-3 (DHe) fusion fuel cycles have been compared. Representative tokamak designs for each fuel cycle were established based on consistent design criteria, using modest extrapolations of present day technologies. The economic analysis of these designs took into account the possible variation in capital and operating costs, and plant availability. Safety analyses examined tritium inventories, routine tritium releases, inventories of activation products and the level of hazard associated with plant wastes. The annual dose incurred by plant workers was estimated for all fuel cycles. The impact of using a reduced activation steel as a blanket material on the economics and safety during normal conditions for the DD fuel cycle was examined. A loss of coolant accident (LOCA) was investigated to determine the relative safety and economic impact of this event for the various fuel cycles. Finally, a cost/benefit analysis was performed to determine if the increased costs associated with these designs are justified by the improved safety which they provide. (orig.)

Life cycle environmental performance of renewable building materials in the context of residential construction : phase II research report: an extension to the 2005 phase I research report. Module L, Life-cycle inventory of hardwood lumber manufacturing in the Southeastern United States.

Science.gov (United States)

Richard D. Bergman; Scott A. Bowe

2010-01-01

The goal of this study was to gain an understanding of the environmental impact of hardwood lumber production through a gate-to-gate life-cycle inventory (LCI) of hardwood sawmills in the Southeastern United States (SE). Primary mill data were collected per Consortium on Research for Renewable Industrial Materials (CORRIM) Research Guidelines. Life-cycle impact...

Analysis of an inventory model for both linearly decreasing demand and holding cost

Science.gov (United States)

Malik, A. K.; Singh, Parth Raj; Tomar, Ajay; Kumar, Satish; Yadav, S. K.

2016-03-01

This study proposes the analysis of an inventory model for linearly decreasing demand and holding cost for non-instantaneous deteriorating items. The inventory model focuses on commodities having linearly decreasing demand without shortages. The holding cost doesn't remain uniform with time due to any form of variation in the time value of money. Here we consider that the holding cost decreases with respect to time. The optimal time interval for the total profit and the optimal order quantity are determined. The developed inventory model is pointed up through a numerical example. It also includes the sensitivity analysis.

Optimal pricing and lot-sizing for perishable inventory with price and time dependent ramp-type demand

Science.gov (United States)

Panda, S.; Saha, S.; Basu, M.

2013-01-01

Product perishability is an important aspect of inventory control. To minimise the effect of deterioration, retailers in supermarkets, departmental store managers, etc. always want higher inventory depletion rate. In this article, we propose a dynamic pre- and post-deterioration cumulative discount policy to enhance inventory depletion rate resulting low volume of deterioration cost, holding cost and hence higher profit. It is assumed that demand is a price and time dependent ramp-type function and the product starts to deteriorate after certain amount of time. Unlike the conventional inventory models with pricing strategies, which are restricted to a fixed number of price changes and to a fixed cycle length, we allow the number of price changes before as well as after the start of deterioration and the replenishment cycle length to be the decision variables. Before start of deterioration, discounts on unit selling price are provided cumulatively in successive pricing cycles. After the start of deterioration, discounts on reduced unit selling price are also provided in a cumulative way. A mathematical model is developed and the existence of the optimal solution is verified. A numerical example is presented, which indicates that under the cumulative effect of price discounting, dynamic pricing policy outperforms static pricing strategy. Sensitivity analysis of the model is carried out.

Assessment of a combined dry anaerobic digestion and post-composting treatment facility for source-separated organic household waste, using material and substance flow analysis and life cycle inventory

DEFF Research Database (Denmark)

Jensen, Morten Bang; Møller, Jacob; Scheutz, Charlotte

2017-01-01

with low uncertainties for non-volatile substances, while balances for nitrogen, carbon, volatile solids and total organic carbon showed larger but reasonable uncertainties, due to volatilisation and emissions into the air. Material and substance flow analyses were performed in order to obtain transfer...... to the biogas, 24% to the compost, 13% to residues and 40% into the atmosphere. For nitrogen, 69% was transferred to the compost, 10% volatilised to the biofilter, 11% directly into the atmosphere and 10% to residues. Finally, a full life cycle inventory was conducted for the combined dry anaerobic digestion...

Assessing the impact of a mountain pine beetle infestation on stand structure of lodgepole pine forests in Colorado using the Forest Inventory and Analysis Annual forest inventory

Science.gov (United States)

Michael T. Thompson

2017-01-01

The Forest Inventory and Analysis (FIA) annual inventory system began in Colorado in 2002, which coincided with the onset of a major mountain pine beetle (Dendroctonus ponderosae) epidemic. The mortality event, coupled with 11 years of annual inventory data, provided an opportunity to assess the usefulness of the FIA annual inventory system for quantifying the effects...

Applying inventory classification to a large inventory management system

Directory of Open Access Journals (Sweden)

Benjamin Isaac May

2017-06-01

Full Text Available Inventory classification aims to ensure that business-driving inventory items are efficiently managed in spite of constrained resources. There are numerous single- and multiple-criteria approaches to it. Our objective is to improve resource allocation to focus on items that can lead to high equipment availability. This concern is typical of many service industries such as military logistics, airlines, amusement parks and public works. Our study tests several inventory prioritization techniques and finds that a modified multi-criterion weighted non-linear optimization (WNO technique is a powerful approach for classifying inventory, outperforming traditional techniques of inventory prioritization such as ABC analysis in a variety of performance objectives.

A life cycle analysis of polymer solar cell modules prepared using roll-to-roll methods under ambient conditions

DEFF Research Database (Denmark)

Espinosa Martinez, Nieves; García-Valverde, Rafael; Urbina, Antonio

2011-01-01

A life cycle analysis was performed on a full roll-to-roll coating procedure used for the manufacture of flexible polymer solar cell modules. The process known as ProcessOne employs a polyester substrate with a sputtered layer of the transparent conductor indium-tin-oxide (ITO). The ITO film was ...... photovoltaic technologies. The results showed that an Energy Pay-Back Time (EPBT) of 2.02 years can be achieved for an organic solar module of 2% efficiency, which could be reduced to 1.35 years, if the efficiency was 3%.......A life cycle analysis was performed on a full roll-to-roll coating procedure used for the manufacture of flexible polymer solar cell modules. The process known as ProcessOne employs a polyester substrate with a sputtered layer of the transparent conductor indium-tin-oxide (ITO). The ITO film...... printed. Finally the polymer solar modules were encapsulated, using a polyester barrier material. All operations except the application of ITO were carried out under ambient conditions. The life cycle analysis delivered a material inventory of the full process for a module production...

Radionuclide inventory and heat generation analysis in disposal of radioactive waste

International Nuclear Information System (INIS)

Suryanto

1997-01-01

Radionuclide inventory and heat generation analysis on spent nuclear fuel were done in order to study the potential radionuclides contributing radiological impact to human being caused by spent fuel disposal. The study was carried out using the Bateman equation of radionuclide decay chains for fission products and actinides. the results showed that Cs-137, Sr-90 and Pu-239 dominated inventory of spent fuel, in which Pu-238 and Pu-240 dominated heat generation during disposal. Accordingly, the above radionuclides could be considered as the reference radionuclides for safety analysis of spent nuclear fuel disposal (author)

Analysis of possible fuel cycles

International Nuclear Information System (INIS)

Boehm, H.; Kessler, G.; Engelmann, P.; Maerkl, H.; Stoll, W.

1978-01-01

A brief survey is presented of the most important fuel cycles. A rough analysis of fuel cycles is attempted under the aspects of proliferation, status of technical feasibility, resource conservation and waste management and the most important criteria for such an analysis are discussed. Among the multitude of potential combinations of fuel cycles and types of reactors only a few have reached a level of technical feasibility which would make them eligible for commercial implementation within the next decade. However, if, for instance, the higher proliferation resistance of a specific fuel cycle is to be utilized to diminish the worldwide proliferation hazard, that cycle would first of all have to be introduced on an industrial scale as quickly as possible. The analysis shows that the reduction of the bazard of worldwide proliferation will continue to be the objective primarily of international agreements and measures taken in the political realm. (orig.) [de

Environmental and ecological life cycle inventories of present and future PV systems in Europe for sustainability policies

International Nuclear Information System (INIS)

Frankl, P.; Lombardelli, S.; Corrado, A.

2004-01-01

The current use of Life Cycle Inventories (LCI) for the calculation of external costs and energy system modelling and planning is limited by two main factors: 1) lack of harmonization and transparency in the methodology used in LCA studies. 2) lack of transparent and updated and database on recent and emerging PV technologies (and other renewable and distributed generation technologies). These issues have been addressed and overcome by the recent EU research project ECLIPSE. With respect to photovoltaic (PV) systems, four main PV technologies (mc-Si, sc-Si, thin film a-Si, CIS) with different applications (ground-mounted power plants, retrofit and integrated building integrated systems) and derived configurations were analyzed, for a total of 47 system configurations. Each main technology is described in a report, which presents results in detailed and transparent manner, highlighting the crucial parameters which influence LCI results. The latter confirm the low life cycle emissions level and the very high value of PV systems towards sustainable energy systems for the future. (authors)

Life-cycle cost analysis of adsorption cycles for desalination

KAUST Repository

Thu, Kyaw

2010-08-01

This paper presents the thermo-economic analysis of the adsorption desalination (AD) cycle that is driven by low-temperature waste heat from exhaust of industrial processes or renewable sources. The AD cycle uses an adsorbent such as the silica gel to desalt the sea or brackish water. Based on an experimental prototype AD plant, the life-cycle cost analysis of AD plants of assorted water production capacities has been simulated and these predictions are translated into unit cost of water production. Our results show that the specific energy consumption of the AD cycle is 1.38 kWh/m3 which is the lowest ever reported. For a plant capacity of 1000 m3/d, the AD cycle offers a unit cost of $0.457/m3 as compared to more than $0.9 for the average RO plants. Besides being cost-effective, the AD cycle is also environment-friendly as it emits less CO2 emission per m3 generated, typically 85% less, by comparison to an RO process. © 2010 Desalination Publications.

Development and application of dynamic hybrid multi-region inventory analysis for macro-level environmental policy analysis. A case study on climate policy in Taiwan

NARCIS (Netherlands)

Chao, C.-W.; Heijungs, R.

2013-01-01

We develop a novel inventory method called Dynamic Hybrid Multi-Region Inventory analysis (DHMRI), which integrates the EEMRIOA and Integrated Hybrid LCA and applies time-dependent environmental intervention information for inventory analysis. Consequently, DHMRI is able to quantify the change in

Application of stochastic approach based on Monte Carlo (MC) simulation for life cycle inventory (LCI) of the rare earth elements (REEs) in beneficiation rare earth waste from the gold processing: case study

Science.gov (United States)

Bieda, Bogusław; Grzesik, Katarzyna

2017-11-01

The study proposes an stochastic approach based on Monte Carlo (MC) simulation for life cycle assessment (LCA) method limited to life cycle inventory (LCI) study for rare earth elements (REEs) recovery from the secondary materials processes production applied to the New Krankberg Mine in Sweden. The MC method is recognizes as an important tool in science and can be considered the most effective quantification approach for uncertainties. The use of stochastic approach helps to characterize the uncertainties better than deterministic method. Uncertainty of data can be expressed through a definition of probability distribution of that data (e.g. through standard deviation or variance). The data used in this study are obtained from: (i) site-specific measured or calculated data, (ii) values based on literature, (iii) the ecoinvent process "rare earth concentrate, 70% REO, from bastnäsite, at beneficiation". Environmental emissions (e.g, particulates, uranium-238, thorium-232), energy and REE (La, Ce, Nd, Pr, Sm, Dy, Eu, Tb, Y, Sc, Yb, Lu, Tm, Y, Gd) have been inventoried. The study is based on a reference case for the year 2016. The combination of MC analysis with sensitivity analysis is the best solution for quantified the uncertainty in the LCI/LCA. The reliability of LCA results may be uncertain, to a certain degree, but this uncertainty can be noticed with the help of MC method.

CFTSIM-ITER dynamic fuel cycle model

International Nuclear Information System (INIS)

Busigin, A.; Gierszewski, P.

1998-01-01

Dynamic system models have been developed for specific tritium systems with considerable detail and for integrated fuel cycles with lesser detail (e.g. D. Holland, B. Merrill, Analysis of tritium migration and deposition in fusion reactor systems, Proceedings of the Ninth Symposium Eng. Problems of Fusion Research (1981); M.A. Abdou, E. Vold, C. Gung, M. Youssef, K. Shin, DT fuel self-sufficiency in fusion reactors, Fusion Technol. (1986); G. Spannagel, P. Gierszewski, Dynamic tritium inventory of a NET/ITER fuel cycle with lithium salt solution blanket, Fusion Eng. Des. (1991); W. Kuan, M.A. Abdou, R.S. Willms, Dynamic simulation of a proposed ITER tritium processing system, Fusion Technol. (1995)). In order to provide a tool to understand and optimize the behavior of the ITER fuel cycle, a dynamic fuel cycle model called CFTSIM is under development. The CFTSIM code incorporates more detailed ITER models, specifically for the important isotope separation system, and also has an easier-to-use graphical interface. This paper provides an overview of CFTSIM Version 1.0. The models included are those with significant and varying tritium inventories over a test campaign: fueling, plasma and first wall, pumping, fuel cleanup, isotope separation and storage. An illustration of the results is shown. (orig.)

Initial Radionuclide Inventories

Energy Technology Data Exchange (ETDEWEB)

H. Miller

2004-09-19

The purpose of this analysis is to provide an initial radionuclide inventory (in grams per waste package) and associated uncertainty distributions for use in the Total System Performance Assessment for the License Application (TSPA-LA) in support of the license application for the repository at Yucca Mountain, Nevada. This document is intended for use in postclosure analysis only. Bounding waste stream information and data were collected that capture probable limits. For commercially generated waste, this analysis considers alternative waste stream projections to bound the characteristics of wastes likely to be encountered using arrival scenarios that potentially impact the commercial spent nuclear fuel (CSNF) waste stream. For TSPA-LA, this radionuclide inventory analysis considers U.S. Department of Energy (DOE) high-level radioactive waste (DHLW) glass and two types of spent nuclear fuel (SNF): CSNF and DOE-owned (DSNF). These wastes are placed in two groups of waste packages: the CSNF waste package and the codisposal waste package (CDSP), which are designated to contain DHLW glass and DSNF, or DHLW glass only. The radionuclide inventory for naval SNF is provided separately in the classified ''Naval Nuclear Propulsion Program Technical Support Document'' for the License Application. As noted previously, the radionuclide inventory data presented here is intended only for TSPA-LA postclosure calculations. It is not applicable to preclosure safety calculations. Safe storage, transportation, and ultimate disposal of these wastes require safety analyses to support the design and licensing of repository equipment and facilities. These analyses will require radionuclide inventories to represent the radioactive source term that must be accommodated during handling, storage and disposition of these wastes. This analysis uses the best available information to identify the radionuclide inventory that is expected at the last year of last emplacement

Periodic review inventory policy for non-instantaneous deteriorating items with time dependent deterioration rate

Directory of Open Access Journals (Sweden)

Anwesha Samanta

2015-09-01

Full Text Available The paper studies a periodic review inventory model with no shortages and different demand rates during pre- and post- deterioration periods . Deterioration of units start after a fixed time interval, and the deterioration rate is time dependent. The model determines the optimal reorder interval and the optimal order quantity so as to minimize the total cost per unit length of an inventory cycle. An extension of the model to include price discount has been further considered. Numerical examples are presented to illustrate the model and a sensitivity analysis is also reported.

Practical Policy Applications of Uncertainty Analysis for National Greenhouse Gas Inventories

International Nuclear Information System (INIS)

Gillenwater, M.; Sussman, F.; Cohen, J.

2007-01-01

goals precisely in terms of relationships among important variables (such as emissions estimate, commitment level, or statistical confidence); and (3) develop a quantifiable adjustment mechanism that reflects these environmental goals. We recommend that countries implement an investigation-focused (i.e., qualitative) uncertainty analysis that will (1) provide the type of information necessary to develop more substantive, and potentially useful, quantitative uncertainty estimates-regardless of whether those quantitative estimates are used for policy purposes; and (2) provide information needed to understand the likely causes of uncertainty in inventory data and thereby point to ways to improve inventory quality (i.e., accuracy, transparency, completeness, and consistency)

Practical Policy Applications of Uncertainty Analysis for National Greenhouse Gas Inventories

Energy Technology Data Exchange (ETDEWEB)

Gillenwater, M. [Environmental Resources Trust (United States)], E-mail: mgillenwater@ert.net; Sussman, F.; Cohen, J. [ICF International (United States)

2007-09-15

goals precisely in terms of relationships among important variables (such as emissions estimate, commitment level, or statistical confidence); and (3) develop a quantifiable adjustment mechanism that reflects these environmental goals. We recommend that countries implement an investigation-focused (i.e., qualitative) uncertainty analysis that will (1) provide the type of information necessary to develop more substantive, and potentially useful, quantitative uncertainty estimates-regardless of whether those quantitative estimates are used for policy purposes; and (2) provide information needed to understand the likely causes of uncertainty in inventory data and thereby point to ways to improve inventory quality (i.e., accuracy, transparency, completeness, and consistency)

Total energy cycle assessment of electric and conventional vehicles: an energy and environmental analysis. Volume 1: technical report

Energy Technology Data Exchange (ETDEWEB)

Cuenca, R.; Formento, J.; Gaines, L.; Marr, B.; Santini, D.; Wang, M. [Argonne National Lab., IL (United States); Adelman, S.; Kline, D.; Mark, J.; Ohi, J.; Rau, N. [National Renewable Energy Lab., Golden, CO (United States); Freeman, S.; Humphreys, K.; Placet, M. [Pacific Northwest National Lab., Richland, WA (United States)

1998-01-01

This report compares the energy use, oil use and emissions of electric vehicles (EVs) with those of conventional, gasoline-powered vehicles (CVs) over the total life cycle of the vehicles. The various stages included in the vehicles` life cycles include vehicle manufacture, fuel production, and vehicle operation. Disposal is not included. An inventory of the air emissions associated with each stage of the life cycle is estimated. Water pollutants and solid wastes are reported for individual processes, but no comprehensive inventory is developed. Volume I contains the major results, a discussion of the conceptual framework of the study, and summaries of the vehicle, utility, fuel production, and manufacturing analyses. It also contains summaries of comments provided by external peer reviewers and brief responses to these comments.

Pushing boundaries: new directions in inventory techniques and applications: Forest Inventory and Analysis (FIA) symposium 2015

Science.gov (United States)

Sharon M. Stanton; Glenn A. Christensen

2016-01-01

These proceedings report invited presentations and contributions to the 2015 Forest Inventory and Analysis (FIA) Symposium, which was hosted by the Research and Development branch of the U.S. Forest Service. As the only comprehensive and continuous census of the forests in the United States, FIA provides strategic information needed to evaluate sustainability of...

A two-echelon production-inventory model for deteriorating items with multiple buyers

NARCIS (Netherlands)

Ghiami, Yousef; Williams, Terry

2015-01-01

In a production-inventory system, the manufacturer produces the items at a rate, e.g. R, dispatches the order quantities to the customers in specific intervals and stores the excess inventory for subsequent deliveries. Therefore each inventory cycle of the manufacturer can be divided into two

Spatial GHG Inventory: Analysis of Uncertainty Sources. A Case Study for Ukraine

International Nuclear Information System (INIS)

Bun, R.; Gusti, M.; Kujii, L.; Tokar, O.; Tsybrivskyy, Y.; Bun, A.

2007-01-01

A geoinformation technology for creating spatially distributed greenhouse gas inventories based on a methodology provided by the Intergovernmental Panel on Climate Change and special software linking input data, inventory models, and a means for visualization are proposed. This technology opens up new possibilities for qualitative and quantitative spatially distributed presentations of inventory uncertainty at the regional level. Problems concerning uncertainty and verification of the distributed inventory are discussed. A Monte Carlo analysis of uncertainties in the energy sector at the regional level is performed, and a number of simulations concerning the effectiveness of uncertainty reduction in some regions are carried out. Uncertainties in activity data have a considerable influence on overall inventory uncertainty, for example, the inventory uncertainty in the energy sector declines from 3.2 to 2.0% when the uncertainty of energy-related statistical data on fuels combusted in the energy industries declines from 10 to 5%. Within the energy sector, the 'energy industries' subsector has the greatest impact on inventory uncertainty. The relative uncertainty in the energy sector inventory can be reduced from 2.19 to 1.47% if the uncertainty of specific statistical data on fuel consumption decreases from 10 to 5%. The 'energy industries' subsector has the greatest influence in the Donetsk oblast. Reducing the uncertainty of statistical data on electricity generation in just three regions - the Donetsk, Dnipropetrovsk, and Luhansk oblasts - from 7.5 to 4.0% results in a decline from 2.6 to 1.6% in the uncertainty in the national energy sector inventory

Life-Cycle Cost-Benefit Analysis

DEFF Research Database (Denmark)

Thoft-Christensen, Palle

2010-01-01

The future use of Life-Cycle Cost-Benefit (LCCB) analysis is discussed in this paper. A more complete analysis including not only the traditional factors and user costs, but also factors which are difficult to include in the analysis is needed in the future.......The future use of Life-Cycle Cost-Benefit (LCCB) analysis is discussed in this paper. A more complete analysis including not only the traditional factors and user costs, but also factors which are difficult to include in the analysis is needed in the future....

Life-Cycle Inventory Analysis of I-joist Production in the United States

Science.gov (United States)

Richard D. Bergman

2015-01-01

Documenting the environmental performance of building products is becoming increasingly common. Creating environmental product declarations (EPDs) based on life-cycle assessment (LCA) data is one approach to provide scientific documentation of the products’ environmental performance. Many U.S. structural wood products have LCA-based “eco-labels” developed under the ISO...

Life-cycle cost analysis of adsorption cycles for desalination

KAUST Repository

Thu, Kyaw; Chakraborty, A.; Saha, B.B.; Chun, Won Gee; Ng, K.C.

2010-01-01

This paper presents the thermo-economic analysis of the adsorption desalination (AD) cycle that is driven by low-temperature waste heat from exhaust of industrial processes or renewable sources. The AD cycle uses an adsorbent such as the silica gel

Development of the Social Inventory Database in Thailand Using Input–Output Analysis

Directory of Open Access Journals (Sweden)

Seksan Papong

2015-06-01

Full Text Available The social life cycle assessment (S-LCA is a technique for assessing social impact and potential impact that aims to evaluate the social and socio-economic aspects of products and their potential for both positive and negative impacts along their life cycle. The lack of a quantitative inventory data for social issues is a weakness of the S-LCA methodology to calculate social impacts. This study aims to establish a social inventory database in Thailand using input–output (IO modeling. The 2005 economic IO table of Thailand is used in this study. The six different social issues are calculated for both direct and indirect social intensity. The social issues include employment, number of female employees, working hours, wages and salaries, and non-fatal and fatal occupational cases. The results indicate that the primary sector has the highest social intensity in terms of employment, female employment, and working hour intensity. Meanwhile, the secondary sector was higher in non-fatal occupational cases intensity than other sectors. For wages intensity, the results show that the government sector was higher than other sectors, it being labor intensive and of low economic value. In addition, the fatal occupational cases shows the highest intensity in the non-metallic mining, fertilizer and pesticides, and construction sectors. In terms of total social impacts or social footprints, the wholesale and retail trade sector had the highest impact for almost all social issues due to the higher final demand in this sector.

Advanced Fuel Cycle Economic Sensitivity Analysis

Energy Technology Data Exchange (ETDEWEB)

David Shropshire; Kent Williams; J.D. Smith; Brent Boore

2006-12-01

A fuel cycle economic analysis was performed on four fuel cycles to provide a baseline for initial cost comparison using the Gen IV Economic Modeling Work Group G4 ECON spreadsheet model, Decision Programming Language software, the 2006 Advanced Fuel Cycle Cost Basis report, industry cost data, international papers, the nuclear power related cost study from MIT, Harvard, and the University of Chicago. The analysis developed and compared the fuel cycle cost component of the total cost of energy for a wide range of fuel cycles including: once through, thermal with fast recycle, continuous fast recycle, and thermal recycle.

B Plant exhaust filter inventory analysis

International Nuclear Information System (INIS)

Lan, J.S.; Wootan, D.W.; Carter, L.L.; Bunch, W.L.; Covey, L.I.; Greenborg, J.

1994-10-01

This paper describes a method for determining radionuclide inventories in filters using measurements of radiation fields that determine photon dose rates and photon-plus-electron dose rates between filter banks. The mathematical approach quantifies the curie inventories of filter banks by using the measured dose rates and the calculated Green's functions involving detector responses per unit source

Mission impossible? The boss wants to double our inventory turns.

Science.gov (United States)

Gips, J

1998-11-01

Despite the prolific implementation of manufacturing systems, JIT principles, Kaizen events, and cycle time reduction programs over the past few years, high inventories still plague many companies. The assumption that implementing these principles and techniques will automatically result in inventory levels that satisfy management frequently proves to be false. Events like mergers, introduction of new competition, and a dropoff in business often trigger edicts to cut inventories. The cost of inventories also extends beyond the traditional accounting measurements to include hidden operating costs that everyone should want to eliminate. This article looks at the reasons for inventories and explores strategies for reducing them.

International inventory of training facilities in nuclear power and its fuel cycle

International Nuclear Information System (INIS)

1977-01-01

Because the development of trained manpower is important for full use of nuclear power, the International Atomic Energy Agency has compiled this first inventory of training facilities and programs. It is based on information submitted by Member States and received up to 31 January 1977. The inventory is arranged by country, type of training organization, and by subject

Statistics and quality assurance for the Northern Research Station Forest Inventory and Analysis Program

Science.gov (United States)

Dale D. Gormanson; Scott A. Pugh; Charles J. Barnett; Patrick D. Miles; Randall S. Morin; Paul A. Sowers; James A. Westfall

2018-01-01

The U.S. Forest Service Forest Inventory and Analysis (FIA) program collects sample plot data on all forest ownerships across the United States. FIA’s primary objective is to determine the extent, condition, volume, growth, and use of trees on the Nation’s forest land through a comprehensive inventory and analysis of the Nation’s forest resources. The FIA program...

Nonproliferation and safeguards aspects of fuel cycle programs in reduction of excess separated plutonium and high-enriched uranium

International Nuclear Information System (INIS)

Persiani, P.J.

1995-01-01

The purpose of this preliminary investigation is to explore alternatives and strategies aimed at the gradual reduction of the excess inventories of separated plutonium and high-enriched uranium (HEU) in the civilian nuclear power industry. The study attempts to establish a technical and economic basis to assist in the formation of alternative approaches consistent with nonproliferation and safeguards concerns. Reference annual mass flows and inventories for a representative 1,400 Mwe Pressurized Water Reactor (PWR) fuel cycle have been investigated for three cases: the 100 percent uranium oxide UO 2 fuel loading once through cycle, and the 33 percent mixed oxide MOX loading configuration for a first and second plutonium recycle. The analysis addresses fuel cycle developments; plutonium and uranium inventory and flow balances; nuclear fuel processing operations; UO 2 once-through and MOX first and second recycles; and the economic incentives to draw-down the excess separated plutonium stores. The preliminary analysis explores several options in reducing the excess separated plutonium arisings and HEU, and the consequences of the interacting synergistic effects between fuel cycle processes and isotopic signatures of nuclear materials on nonproliferation and safeguards policy assessments

Introducing advanced nuclear fuel cycles in Canada

International Nuclear Information System (INIS)

Duret, M.F.

1978-05-01

The ability of several different advanced fuel cycles to provide energy for a range of energy growth scenarios has been examined for a few special situations of interest in Canada. Plutonium generated from the CANDU-PHW operating on natural uranium is used to initiate advanced fuel cycles in the year 2000. The four fuel cycles compared are: 1) natural uranium in the CANDU-PHW; 2) high burnup thorium cycle in the CANDU-PHW; 3) self-sufficient thorium cycle in the CANDU-PHW; 4) plutonium-uranium cycle in a fast breeder reactor. The general features of the results are quite clear. While any plutonium generated prior to the introduction of the advanced fuel cycle remains, system requirements for natural uranium for each of the advanced fuel cycles are the same and are governed by the rate at which plants operating on natural uranium can be retired. When the accumulated plutonium inventory has been entirely used, natural uranium is again required to provide inventory for the advanced fuel cycle reactors. The time interval during which no uranium is required varies only from about 25 to 40 years for both thorium cycles, depending primarily on the energy growth rate. The breeder does not require the entire plutonium inventory produced and so would call for less processing of fuel from the PHW reactors. (author)

BWROPT: A multi-cycle BWR fuel cycle optimization code

Energy Technology Data Exchange (ETDEWEB)

Ottinger, Keith E.; Maldonado, G. Ivan, E-mail: Ivan.Maldonado@utk.edu

2015-09-15

Highlights: • A multi-cycle BWR fuel cycle optimization algorithm is presented. • New fuel inventory and core loading pattern determination. • The parallel simulated annealing algorithm was used for the optimization. • Variable sampling probabilities were compared to constant sampling probabilities. - Abstract: A new computer code for performing BWR in-core and out-of-core fuel cycle optimization for multiple cycles simultaneously has been developed. Parallel simulated annealing (PSA) is used to optimize the new fuel inventory and placement of new and reload fuel for each cycle considered. Several algorithm improvements were implemented and evaluated. The most significant of these are variable sampling probabilities and sampling new fuel types from an ordered array. A heuristic control rod pattern (CRP) search algorithm was also implemented, which is useful for single CRP determinations, however, this feature requires significant computational resources and is currently not practical for use in a full multi-cycle optimization. The PSA algorithm was demonstrated to be capable of significant objective function reduction and finding candidate loading patterns without constraint violations. The use of variable sampling probabilities was shown to reduce runtime while producing better results compared to using constant sampling probabilities. Sampling new fuel types from an ordered array was shown to have a mixed effect compared to random new fuel type sampling, whereby using both random and ordered sampling produced better results but required longer runtimes.

A system dynamics model for tritium cycle of pulsed fusion reactor

International Nuclear Information System (INIS)

Zhu, Zuolong; Nie, Baojie; Chen, Dehong

2017-01-01

As great challenges and uncertainty exist in achieving steady plasma burning, pulsed plasma burning may be a potential scenario for fusion engineering test reactor, even for fusion DEMOnstration reactor. In order to analyze dynamic tritium inventory and tritium self-sufficiency for pulsed fusion systems, a system dynamics model of tritium cycle was developed on the basis of earlier version of Tritium Analysis program for fusion System (TAS). The model was verified with TRIMO, which was developed by KIT in Germany. Tritium self-sufficiency and dynamic tritium inventory assessment were performed for a typical fusion engineering test reactor. The verification results show that the system dynamics model can be used for tritium cycle analysis of pulsed fusion reactor with sufficient reliability. The assessment results of tritium self-sufficiency indicate that the fusion reactor might only need several hundred gram tritium to startup if achieved high efficient tritium handling ability (Referred ITER: 1 h). And the initial tritium startup inventory in pulsed fusion reactor is determined by the combined influence of pulse length, burn availability, and tritium recycle time. Meanwhile, tritium self-sufficiency can be achieved under the defined condition.

A system dynamics model for tritium cycle of pulsed fusion reactor

Energy Technology Data Exchange (ETDEWEB)

Zhu, Zuolong; Nie, Baojie [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); University of Science and Technology of China, Hefei, Anhui, 230027 (China); Chen, Dehong, E-mail: dehong.chen@fds.org.cn [Key Laboratory of Neutronics and Radiation Safety, Institute of Nuclear Energy Safety Technology, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China)

2017-05-15

As great challenges and uncertainty exist in achieving steady plasma burning, pulsed plasma burning may be a potential scenario for fusion engineering test reactor, even for fusion DEMOnstration reactor. In order to analyze dynamic tritium inventory and tritium self-sufficiency for pulsed fusion systems, a system dynamics model of tritium cycle was developed on the basis of earlier version of Tritium Analysis program for fusion System (TAS). The model was verified with TRIMO, which was developed by KIT in Germany. Tritium self-sufficiency and dynamic tritium inventory assessment were performed for a typical fusion engineering test reactor. The verification results show that the system dynamics model can be used for tritium cycle analysis of pulsed fusion reactor with sufficient reliability. The assessment results of tritium self-sufficiency indicate that the fusion reactor might only need several hundred gram tritium to startup if achieved high efficient tritium handling ability (Referred ITER: 1 h). And the initial tritium startup inventory in pulsed fusion reactor is determined by the combined influence of pulse length, burn availability, and tritium recycle time. Meanwhile, tritium self-sufficiency can be achieved under the defined condition.

National inventory of radioactive wastes and valorizable materials. Synthesis report

International Nuclear Information System (INIS)

2004-01-01

This national inventory of radioactive wastes is a reference document for professionals and scientists of the nuclear domain and also for any citizen interested in the management of radioactive wastes. It contains: 1 - general introduction; 2 - the radioactive wastes: definition, classification, origin and management; 3 - methodology of the inventory: organization, accounting, prospective, production forecasting, recording of valorizable materials, exhaustiveness, verification tools; 4 - general results: radioactive waste stocks recorded until December 31, 2002, forecasts for the 2003-2020 era, post-2020 prospects: dismantling operations, recording of valorizable materials; 5 - inventory per producer or owner: front-end fuel cycle facilities, power generation nuclear centers, back-end fuel cycle facilities, waste processing or maintenance facilities, civil CEA research centers, non-CEA research centers, medical activities (diagnostics, therapeutics, analyses), various industrial activities (sources fabrication, control, particular devices), military research and experiment centers, storage and disposal facilities; 6 - elements about radioactive polluted sites; 7 - examples of foreign inventories; 8 - conclusion and appendixes. (J.S.)

Total energy cycle assessment of electric and conventional vehicles: an energy and environmental analysis. Volume 2: appendices A-D to technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

This report compares the energy use, oil use and emissions of electric vehicles (EVs) with those of conventional, gasoline- powered vehicles (CVs) over the total life cycle of the vehicles. The various stages included in the vehicles` life cycles include vehicle manufacture, fuel production, and vehicle operation. Disposal is not included. An inventory of the air emissions associated with each stage of the life cycle is estimated. Water pollutants and solid wastes are reported for individual processes, but no comprehensive inventory is developed. Volume II contains additional details on the vehicle, utility, and materials analyses and discusses several details of the methodology.

Total energy cycle assessment of electric and conventional vehicles: an energy and environmental analysis. Volume 4: peer review comments on technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

This report compares the energy use, oil use and emissions of electric vehicles (EVs) with those of conventional, gasoline-powered vehicles (CVs) over the total life cycle of the vehicles. The various stages included in the vehicles` life cycles include vehicle manufacture, fuel production, and vehicle operation. Disposal is not included. An inventory of the air emissions associated with each stage of the life cycle is estimated. Water pollutants and solid wastes are reported for individual processes, but no comprehensive inventory is developed. Volume IV includes copies of all the external peer review comments on the report distributed for review in July 1997.

Life cycle based dynamic assessment coupled with multiple criteria decision analysis

DEFF Research Database (Denmark)

Sohn, Joshua; Kalbar, Pradip; Birkved, Morten

2017-01-01

the service life of the building. This case study uses both the established and the coupled MCDA assessment methods to quantify and assess the balance of impacts between the production of mineral wool insulation versus the production of space heat. The use of TOPSIS method for calculating single scores......This work looks at coupling Life cycle assessment (LCA) with a dynamic inventory and multiple criteria decision analysis (MCDA) to improve the validity and reliability of single score results for complex systems. This is done using the case study of a representative Danish single family home over...... not matter which impact assessment is applied. However, for the scenarios where other impact categories vary inversely or independently from the climate change impact indicator, such as with renewable energy production, there is need for a more unconventional method, such as the TOPSIS method...

Development of dynamic simulation code for fuel cycle fusion reactor

Energy Technology Data Exchange (ETDEWEB)

Aoki, Isao; Seki, Yasushi [Department of Fusion Engineering Research, Naka Fusion Research Establishment, Japan Atomic Energy Research Institute, Naka, Ibaraki (Japan); Sasaki, Makoto; Shintani, Kiyonori; Kim, Yeong-Chan

1999-02-01

A dynamic simulation code for fuel cycle of a fusion experimental reactor has been developed. The code follows the fuel inventory change with time in the plasma chamber and the fuel cycle system during 2 days pulse operation cycles. The time dependence of the fuel inventory distribution is evaluated considering the fuel burn and exhaust in the plasma chamber, purification and supply functions. For each subsystem of the plasma chamber and the fuel cycle system, the fuel inventory equation is written based on the equation of state considering the fuel burn and the function of exhaust, purification, and supply. The processing constants of subsystem for steady states were taken from the values in the ITER Conceptual Design Activity (CDA) report. Using this code, the time dependence of the fuel supply and inventory depending on the burn state and subsystem processing functions are shown. (author)

Assessment of Used Nuclear Fuel Inventory Relative to Disposition Options

International Nuclear Information System (INIS)

Wagner, John C.; Peterson, Joshua L.; Mueller, Don; Gehin, Jess C.; Worrall, Andrew; Taiwo, Temitope; Nutt, Mark; Williamson, Mark A.; Todosow, Mike; Wigeland, Roald; Halsey, William; Omberg, Ronald; Swift, Peter; Carter, Joe

2013-01-01

This paper presents a technical assessment of the current inventory [∼70,150 metric tons of heavy metal (MTHM) as of 2011] of U.S.-discharged used nuclear fuel (UNF) to support decisions regarding fuel cycle strategies and research, development and demonstration (RD and D) needs. The assessment considered discharged UNF from commercial nuclear electricity generation and defense and research programs and determined that the current UNF inventory can be divided into the following three categories: 1. Disposal - excess material that is not needed for other purposes; 2. Research - material needed for RD and D purposes to support waste management (e.g., UNF storage, transportation, and disposal) and development of alternative fuel cycles (e.g., separations and advanced fuels/reactors); and 3. Recycle/Recovery - material with inherent and/or strategic value. A set of key assumptions and attributes relative to the disposition options was used to categorize the current UNF inventory. Based on consideration of RD and D needs, time frames and material needs for deployment of alternative fuel cycles, characteristics of the current UNF inventory, and possible uses to support national security interests, it was determined that the vast majority of the category, without the need for retrieval for reuse or research purposes. Access to the material in the Research and Recycle/Recovery categories should be retained to support RD and D needs and national security interests. This assessment does not assume any decision about future fuel cycle options or preclude any potential options, including those with potential recycling of commercial UNF, since the ∼2,000 MTHM that is generated annually could provide the feedstock needed for deployment of alternative fuel cycles.

A Logistic Life Cycle Cost-Benefit Analysis of Power Quality Management in the Avionics Repair Facility

National Research Council Canada - National Science Library

Kennedy, Christopher

1998-01-01

.... The implementation of power quality management can result in wide scale logistical support changes in regards to the life cycle costs of maintaining the DoD's current inventory of sensitive electronic equipment...

Inventory of activation analysis facilities available in the European Community to Industrial users

International Nuclear Information System (INIS)

Pauwels, J.

1975-01-01

This inventory includes lists of activation equipment produced in the European Community, facilities available for industrial users and activation laboratories existing in the European companies. The aim of this inventory is to provide all information that may be useful, to companies interested in activation analysis, as well as to give an idea on existing routine applications and on the European market in facilities

Invasive plants found in east Texas forests, 2009 forest inventory and analysis factsheet

Science.gov (United States)

Sonja N. Oswalt; Christopher M. Oswalt

2011-01-01

This science update provides information on the presence and cover of nonnative invasive plants found in forests of the eastern region of the State of Texas based on an annual inventory conducted by the Forest Inventory and Analysis (FIA) Program at the Southern Research Station of the U.S. Department of Agriculture Forest Service in cooperation with the Texas Forest...

National dam inventory provides data for analysis

International Nuclear Information System (INIS)

Spragens, L.

1992-01-01

The Association of State Dam Safety Officials completed a dam inventory this fall. Information on approximately 90,000 state-regulated dams in the US collected during the four-year inventory is being used to build a database managed by the Federal Emergency Management Agency. In addition to ASDSO's work, the federal government conducted an inventory of federal dams. This data will be added to the state information to form one national database. The database will feature 35 data fields for each entry, including the name of the dam, its size, the name of the nearest downstream community, maximum discharge and storage volume, the date of the last inspection, and details about the emergency action plan. The program is an update of the nation's first dam inventory, required by the Dam Safety Act of 1972. The US Army Corps of Engineers completed the original inventory in 1981. The Water Resources Development Act of 1986 authorized appropriations of $2.5 million for the Corps to update the inventory. FEMA and the Corps entered into an agreement for FEMA to undertake the task for the Corps and to coordinate work on both the federal and state inventories. ASDSO compiles existing information on state-regulated dams into a common format for the database, added missing information, and established a process for continually updating data. ASDSO plans to analyze the information collected for the database. It will look at statistics for the number of dams regulated, communities that could be affected, and the number of high-hazard dams. FEMA is preparing reports for Congress on the project. The reports, which are expected to be ready by May 1993, will include information on the methodology used and facts about regulated dams under state jurisdiction

Status of life cycle inventories for batteries

International Nuclear Information System (INIS)

Sullivan, J.L.; Gaines, L.

2012-01-01

Highlights: ► Cradle-to-gate (ctg) energy and emissions compared among five battery systems. ► Calculate material production values fall well within observed ranges. ► Values based on recycled materials in poor agreement with observed ranges. ► Material production data needed for recycled and some virgin battery materials. ► Battery manufacturing data range widely and hence also need updating. - Abstract: This study reviews existing life-cycle inventory (LCI) results for cradle-to-gate (ctg) environmental assessments of lead-acid (PbA), nickel–cadmium (NiCd), nickel-metal hydride (NiMH), sodium-sulfur (Na/S), and lithium-ion (Li-ion) batteries. LCI data are evaluated for the two stages of cradle-to-gate performance: battery material production and component fabrication and assembly into purchase ready batteries. Using existing production data on battery constituent materials, overall battery material production values were calculated and contrasted with published values for the five battery technologies. The comparison reveals a more prevalent absence of material production data for lithium ion batteries, though such data are also missing or dated for a few important constituent materials in nickel metal hydride, nickel cadmium, and sodium sulfur batteries (mischmetal hydrides, cadmium, β-alumina). Despite the overall availability of material production data for lead acid batteries, updated results for lead and lead peroxide are also needed. On the other hand, LCI data for the commodity materials common to most batteries (steel, aluminum, plastics) are up to date and of high quality, though there is a need for comparable quality data for copper. Further, there is an almost total absence of published LCI data on recycled battery materials, an unfortunate state of affairs given the potential benefit of battery recycling. Although battery manufacturing processes have occasionally been well described, detailed quantitative information on energy and

Deuterium inventory in Tore Supra: reconciling particle balance and post-mortem analysis

International Nuclear Information System (INIS)

Tsitrone, E.; Brosset, C.; Pegourie, B.; Gauthier, E.; Bouvet, J.; Bucalossi, J.; Carpentier, S.; Corre, Y.; Delchambre, E.; Dittmar, T.; Douai, D.; Ekedahl, A.; Ghendrih, Ph.; Grisolia, C.; Grosman, A.; Gunn, J.; Hong, S.H.; Desgranges, L.; Escarguel, A.; Jacob, W.

2009-01-01

Fuel retention, a crucial issue for next step devices, is assessed in present-day tokamaks using two methods: particle balance performed during shots and post-mortem analysis carried out during shutdowns between experimental campaigns. Post-mortem analysis generally gives lower estimates of fuel retention than integrated particle balance. In order to understand the discrepancy between these two methods, a dedicated experimental campaign has been performed in Tore Supra to load the vessel walls with deuterium (D) and monitor the trapped D inventory through particle balance. The campaign was followed by an extensive post-mortem analysis phase of the Tore Supra limiter. This paper presents the status of the analysis phase, including the assessment of the D content in the castellated tile structure of the limiter. Indeed, using combined surface analysis techniques, it was possible to derive the relative contributions of different zones of interest on the limiter (erosion, thick deposits, thin deposits), showing that the post-mortem inventory is mainly due to codeposition (90% of the total), in particular due to gap deposits. However, deuterium was also evidenced deep into the material in erosion zones (10% of the total). At the present stage of the analysis, 50% of the inventory deduced from particle balance has been found through post-mortem analysis, a significant progress with respect to previous studies (factor 8-10 discrepancy). This shows that post-mortem analysis can be consistent with particle balance provided specific procedures are implemented (dedicated campaign followed by extensive post-mortem analysis). Both techniques are needed for a reliable assessment of fuel retention in tokamaks, giving complementary information on how much and where fuel is retained in the vessel walls.

Sistem Optimasi Inventory Berbasis Layanan Web Di PT Pelita Biru

Directory of Open Access Journals (Sweden)

Cristeddy Asa Bakti

2017-05-01

Full Text Available Various types of LPG sold, requiring a precise inventory management, especially the facts on the ground are often encountered uncertainties include uncertainty of demand and the performance cycle. The aim of this research  is to develop  decision making system to optimize inventory by the Economic Order Quantity method based on the Bowersox formula by using the combining of variables for demand uncertainty and performance cycle. The system uses the web service media method for easy access and maintenance with centralized data on the server and users only use the existing browser. The method of categorizing goods uses the category ABC by dividing the type of goods into categories A (very important, B (important and C (not important. The results provide safe inventory value calculations based on variables of  uncertainty and performance cycles. With the optimization resulting from this system, the company can maintain the availability of the goods by making appropriate arrangements, priorities, and the amount so as to minimize the occurrence of the possibility of excess and lack of stock.

Analysis within the systems development life-cycle

CERN Document Server

Rock-Evans, Rosemary

1987-01-01

Analysis within the Systems Development Life-Cycle: Book 1, Data Analysis-The Deliverables provides a comprehensive treatment of data analysis within the systems development life-cycle and all the deliverables that need to be collected in analysis. The purpose of deliverables is explained and a number of alternative ways of collecting them are discussed. This book is comprised of five chapters and begins with an overview of what """"analysis"""" actually means, with particular reference to tasks such as hardware planning and software evaluation and where they fit into the overall cycle. The ne

Development of a Life Cycle Inventory of Water Consumption Associated with the Production of Transportation Fuels

Energy Technology Data Exchange (ETDEWEB)

Lampert, David J. [Argonne National Lab. (ANL), Argonne, IL (United States); Cai, Hao [Argonne National Lab. (ANL), Argonne, IL (United States); Wang, Zhichao [Argonne National Lab. (ANL), Argonne, IL (United States); Keisman, Jennifer [Argonne National Lab. (ANL), Argonne, IL (United States); Wu, May [Argonne National Lab. (ANL), Argonne, IL (United States); Han, Jeongwoo [Argonne National Lab. (ANL), Argonne, IL (United States); Dunn, Jennifer [Argonne National Lab. (ANL), Argonne, IL (United States); Sullivan, John L. [Argonne National Lab. (ANL), Argonne, IL (United States); Elgowainy, Amgad [Argonne National Lab. (ANL), Argonne, IL (United States); Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States); Keisman, Jennifer [American Association for the Advancemetn of Science (AAAS), Washington, DC (United States)

2015-10-01

The production of all forms of energy consumes water. To meet increased energy demands, it is essential to quantify the amount of water consumed in the production of different forms of energy. By analyzing the water consumed in different technologies, it is possible to identify areas for improvement in water conservation and reduce water stress in energy-producing regions. The transportation sector is a major consumer of energy in the United States. Because of the relationships between water and energy, the sustainability of transportation is tied to management of water resources. Assessment of water consumption throughout the life cycle of a fuel is necessary to understand its water resource implications. To perform a comparative life cycle assessment of transportation fuels, it is necessary first to develop an inventory of the water consumed in each process in each production supply chain. The Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model is an analytical tool that can used to estimate the full life-cycle environmental impacts of various transportation fuel pathways from wells to wheels. GREET is currently being expanded to include water consumption as a sustainability metric. The purpose of this report was to document data sources and methodologies to estimate water consumption factors (WCF) for the various transportation fuel pathways in GREET. WCFs reflect the quantity of freshwater directly consumed per unit production for various production processes in GREET. These factors do not include consumption of precipitation or low-quality water (e.g., seawater) and reflect only water that is consumed (i.e., not returned to the source from which it was withdrawn). The data in the report can be combined with GREET to compare the life cycle water consumption for different transportation fuels.

Studying the effect on system preference by varying coproduct allocation in creating life-cycle inventory.

Science.gov (United States)

Curran, Mary Ann

2007-10-15

How one models the input and output data for a life-cycle assessment (LCA) can greatly affect the results. Although much attention has been paid to allocation methodology by researchers in the field, specific guidance is still lacking: Earlier research focused on the effects of applying various allocation schemes to industrial processes when creating life-cycle inventories. To determine the impact of different allocation approaches upon product choice, this study evaluated the gas- and water-phase emissions during the production, distribution, and use of three hypothetical fuel systems (data that represent conventional gasoline and gasoline with 8.7 and 85% ethanol were used as the basis for modeling). This paper presents an explanation of the allocation issue and the results from testing various allocation schemes (weight, volume, market value, energy, and demand-based) when viewed across the entire system. Impact indicators for global warming, ozone depletion, and human health noncancer (water impact) were lower for the ethanol-containing fuels, while impact indicators for acidification, ecotoxicity, eutrophication, human health criteria, and photochemical smog were lower for conventional gasoline (impacts for the water-related human health cancer category showed mixed results). The relative ranking of conventional gasoline in relation to the ethanol-containing fuels was consistent in all instances, suggesting that, in this case study, the choice of allocation methodology had no impact on indicating which fuel has lower environmental impacts.

Surface erosion and tritium inventory analysis for CIT [Compact Ignition Tokamak

International Nuclear Information System (INIS)

Brooks, J.N.; Dylla, H.F.

1990-09-01

The expected buildup of co-deposited tritium on the CIT carbon divertor and first wall surfaces and operational methods of minimizing the inventory have been examined. The analysis uses impurity transport computer codes, and associated plasma and tritium retention models, to compute the thickness of redeposited sputtered carbon and the resulting co-deposited tritium inventory on the divertor plates and first wall. Predicted erosion/growth rates are dominated by the effect of gaps between carbon tiles. The overall results appear favorable, showing stable operation (finite self-sputtering) and acceptably low (∼25 Ci/pulse) co-deposited tritium rates, at high surface temperature (1700 degree C) design conditions. These results, however, are highly speculative due to serious model inadequacies at the high sputtering rates predicted. If stable operation is obtainable, the prospects appear good for adequate tritium inventory control via helium-oxygen glow discharge cleaning. 25 refs

Analysis of advanced european nuclear fuel cycle scenarios including transmutation and economical estimates

International Nuclear Information System (INIS)

Merino Rodriguez, I.; Alvarez-Velarde, F.; Martin-Fuertes, F.

2013-01-01

In this work the transition from the existing Light Water Reactors (LWR) to the advanced reactors is analyzed, including Generation III+ reactors in a European framework. Four European fuel cycle scenarios involving transmutation options have been addressed. The first scenario (i.e., reference) is the current fleet using LWR technology and open fuel cycle. The second scenario assumes a full replacement of the initial fleet with Fast Reactors (FR) burning U-Pu MOX fuel. The third scenario is a modification of the second one introducing Minor Actinide (MA) transmutation in a fraction of the FR fleet. Finally, in the fourth scenario, the LWR fleet is replaced using FR with MOX fuel as well as Accelerator Driven Systems (ADS) for MA transmutation. All scenarios consider an intermediate period of GEN-III+ LWR deployment and they extend for a period of 200 years looking for equilibrium mass flows. The simulations were made using the TR-EVOL code, a tool for fuel cycle studies developed by CIEMAT. The results reveal that all scenarios are feasible according to nuclear resources demand (U and Pu). Concerning to no transmutation cases, the second scenario reduces considerably the Pu inventory in repositories compared to the reference scenario, although the MA inventory increases. The transmutation scenarios show that elimination of the LWR MA legacy requires on one hand a maximum of 33% fraction (i.e., a peak value of 26 FR units) of the FR fleet dedicated to transmutation (MA in MOX fuel, homogeneous transmutation). On the other hand a maximum number of ADS plants accounting for 5% of electricity generation are predicted in the fourth scenario (i.e., 35 ADS units). Regarding the economic analysis, the estimations show an increase of LCOE (Levelized cost of electricity) - averaged over the whole period - with respect to the reference scenario of 21% and 29% for FR and FR with transmutation scenarios respectively, and 34% for the fourth scenario. (authors)

Development of dynamic simulation code for fuel cycle of fusion reactor

International Nuclear Information System (INIS)

Aoki, Isao; Seki, Yasushi; Sasaki, Makoto; Shintani, Kiyonori; Kim, Yeong-Chan

1999-02-01

A dynamic simulation code for fuel cycle of a fusion experimental reactor has been developed. The code follows the fuel inventory change with time in the plasma chamber and the fuel cycle system during 2 days pulse operation cycles. The time dependence of the fuel inventory distribution is evaluated considering the fuel burn and exhaust in the plasma chamber, purification and supply functions. For each subsystem of the plasma chamber and the fuel cycle system, the fuel inventory equation is written based on the equation of state considering the fuel burn and the function of exhaust, purification, and supply. The processing constants of subsystem for steady states were taken from the values in the ITER Conceptual Design Activity (CDA) report. Using this code, the time dependence of the fuel supply and inventory depending on the burn state and subsystem processing functions are shown. (author)

Uranium requirements for advanced fuel cycles in expanding nuclear power systems

International Nuclear Information System (INIS)

Banerjee, S.; Tamm, H.

1978-01-01

When considering advanced fuel cycle strategies in rapidly expanding nuclear power systems, equilibrium analyses do not apply. A computer simulation that accounts for system delay times and fissile inventories has been used to study the effects of different fuel cycles and different power growth rates on uranium consumption. The results show that for a given expansion rate of installed capacity, the main factors that affect resource requirements are the fissile inventory needed to introduce the advanced fuel cycle and the conversion (or breeding) ratio. In rapidly expanding systems, the effect of fissile inventory dominates, whereas in slowly expanding systems, conversion or breeding ratio dominates. Heavy-water-moderated and -cooled reactors, with their high conversion ratios, appear to be adaptable vehicles for accommodating fuel cycles covering a wide range of initial fissile inventories. They are therefore particularly suitable for conserving uranium over a wide range of nuclear power system expansion rates

Sensitivity analysis of tritium breeding ratio and startup inventory for CFETR

Energy Technology Data Exchange (ETDEWEB)

Pan, Lei; Chen, Hongli; Zeng, Qin, E-mail: zengqin@ustc.edu.cn

2016-11-15

Highlights: • Through the calculation method of the model, it was found that the increase of the artificially determined startup inventory I0 causes significant increase of TBRreq and the increase of the achievable tritium breeding ratio TBRachiv leads to the decrease of the Im. • The increase of fueling efficiency and fractional burnup significantly contributes to the decrease of both Im and TBRreq, while the increase of the duty time and availability results in the decrease of TBRreq and the proportional increase of Im. • The outer tritium plant parameters of some subsystems that have relatively big tritium throughput have intense influence on either Im or TBRreq. - Abstract: In order to evaluate the tritium self-sufficiency of fusion plant, citing CFETR (Chinese Fusion Engineering Testing Reactor) as an example, a modified tritium fuel cycle model was developed. The calculation method of this model to obtain the minimum startup inventory I{sub m} and its corresponding required minimum tritium breeding ratio TBR{sub req} was first introduced. Then the model was utilized to analyze the influence on I{sub m} and TBR{sub req} by all tritium cycle parameters that were classified into two categories, namely, the tritium burning parameters and the outer tritium plant parameters. As for the tritium burning parameters, the increase of fueling efficiency and fractional burnup significantly contributes to the decrease of both I{sub m} and TBR{sub req}, while the increase of the duty time and availability results in the decrease of TBR{sub req} and the proportional increase of I{sub m}. As for the outer tritium plant parameters, it was found that the outer tritium plant parameters of some subsystems that have relatively big tritium throughput have intense influence on either I{sub m} or TBR{sub req}.

Using mental mapping to unpack perceived cycling risk.

Science.gov (United States)

Manton, Richard; Rau, Henrike; Fahy, Frances; Sheahan, Jerome; Clifford, Eoghan

2016-03-01

Cycling is the most energy-efficient mode of transport and can bring extensive environmental, social and economic benefits. Research has highlighted negative perceptions of safety as a major barrier to the growth of cycling. Understanding these perceptions through the application of novel place-sensitive methodological tools such as mental mapping could inform measures to increase cyclist numbers and consequently improve cyclist safety. Key steps to achieving this include: (a) the design of infrastructure to reduce actual risks and (b) targeted work on improving safety perceptions among current and future cyclists. This study combines mental mapping, a stated-preference survey and a transport infrastructure inventory to unpack perceptions of cycling risk and to reveal both overlaps and discrepancies between perceived and actual characteristics of the physical environment. Participants translate mentally mapped cycle routes onto hard-copy base-maps, colour-coding road sections according to risk, while a transport infrastructure inventory captures the objective cycling environment. These qualitative and quantitative data are matched using Geographic Information Systems and exported to statistical analysis software to model the individual and (infra)structural determinants of perceived cycling risk. This method was applied to cycling conditions in Galway City (Ireland). Participants' (n=104) mental maps delivered data-rich perceived safety observations (n=484) and initial comparison with locations of cycling collisions suggests some alignment between perception and reality, particularly relating to danger at roundabouts. Attributing individual and (infra)structural characteristics to each observation, a Generalised Linear Mixed Model statistical analysis identified segregated infrastructure, road width, the number of vehicles as well as gender and cycling experience as significant, and interactions were found between individual and infrastructural variables. The paper

Energy and exergy analysis of integrated system of ammonia–water Kalina–Rankine cycle

International Nuclear Information System (INIS)

Chen, Yaping; Guo, Zhanwei; Wu, Jiafeng; Zhang, Zhi; Hua, Junye

2015-01-01

The integrated system of AWKRC (ammonia–water Kalina–Rankine cycle) is a novel cycle operated on KC (Kalina cycle) for power generation in non-heating seasons and on AWRC (ammonia–water Rankine cycle) for cogeneration of power and heating water in winter. The influences of inlet temperatures of both heat resource and cooling water on system efficiencies were analyzed based on the first law and the second law of thermodynamics. The calculation is based on following conditions that the heat resource temperature keeps 300 °C, the cooling water temperature for the KC or AWRC is respectively 25 °C or 15 °C; and the temperatures of heating water and backwater are respectively 90 °C and 40 °C. The results show that the evaluation indexes of the power recovery efficiency and the exergy efficiency of KC were respectively 18.2% and 41.9%, while the composite power recovery efficiency and the composite exergy efficiency of AWRC are respectively 21.1% and 43.0% accounting both power and equivalent power of cogenerated heating capacity, including 54.5% heating recovery ratio or 12.4% heating water exergy efficiency. The inventory flow diagrams of both energy and exergy gains and losses of the components operating on KC or AWRC are also demonstrated. - Highlights: • An integrated system of AWKRC (ammonia–water Kalina–Rankine cycle) is investigated. • NH_3–H_2O Rankine cycle is operated for cogenerating power and heating-water in winter. • Heating water with 90 °C and capacity of 54% total reclaimed heat load is cogenerated. • Kalina cycle is operated for power generation in other seasons with high efficiency. • Energy and exergy analysis draw similar results in optimizing the system parameters.

Factor Analysis of the Coopersmith Self-Esteem Inventory

OpenAIRE

Güloğlu, Berna; Aydın, Gül

2001-01-01

This study investigated the factor structure of the Turkish version of the Coopersmith Self-Esteem Inventory. The results showed that the inventory had a 21-factor highly complex factor structure. However of the empirically found 21 factors only 10 seemed theoretically meaningful. The results were discussed in comparison to the fndings obtained from the studies that were carried out with the original version of the Coopersmith Self-esteem Inventory.

Life-Cycle Inventory Analysis of Laminated Veneer Lumber Production in the United States

Science.gov (United States)

Richard D. Bergman

2015-01-01

Documenting the environmental performance of building products is becoming increasingly common. Developing environmental product declarations (EPDs) based on life-cycle assessment (LCA) data is one way to provide scientific documentation. Many U.S. structural wood products have LCA-based “eco-labels” using the ISO standard. However, the standard requires underlying...

The Organisational Culture Assessment Inventory: A Metaphorical Analysis in Educational Settings.

Science.gov (United States)

Steinhoff, Carl R.; Owens, Robert G.

1989-01-01

A preliminary analysis of the Organizational Culture Assessment Inventory yielded four root metaphors descriptive of the type of culture likely to be found in public schools: the family, the machine, the circus, and the "little shop of horrors." (10 references) (SI)

A framework for social life cycle impact assessment

DEFF Research Database (Denmark)

Dreyer, Louise Camilla; Hauschild, Michael Zwicky; Schierbeck, Jens

2006-01-01

Goal, Scope and Background. To enhance the use of life cycle assessment (LCA) as a tool in business decision-making, a methodology for Social life cycle impact assessment (LCIA) is being developed. Social LCA aims at facilitating companies to conduct business in a socially responsible manner...... by providing information about the potential social impacts on people caused by the activities in the life cycle of their product. The development of the methodology has been guided by a business perspective accepting that companies, on the one hand, have responsibility for the people affected...... in the life cycle rather than to the individual industrial processes, as is the case in Environmental LCA. Inventory analysis is therefore focused on the conduct of the companies engaged in the life cycle. A consequence of this view is that a key must be determined for relating the social profiles...

An attributional life cycle assessment for an Italian residential multifamily building.

Science.gov (United States)

Vitale, Pierluca; Arena, Umberto

2017-09-06

The study describes an attributional life cycle assessment carried out according to the ISO standards and focused on an Italian multifamily residential building. The aim was developing an exhaustive and reliable inventory of high-quality primary data, comparing the environmental impacts along the three stages of the building life cycle. The pre-use phase takes into account the production of all the construction materials, transportation, and on-site assembling. The use phase quantifies the resource consumptions for 50 years of the building utilization and ordinary maintenance. The end-of-life phase includes the building demolition and the management of generated wastes. The results quantify how the design criteria affect the environmental performances of the residential building along its life cycle. The role of the pre-use phase appears remarkable for global warming potential (GWP), due to the huge impacts of steel and concrete production processes. The use phase gives the largest contributions, which reach 77% and 84% of the total, for the categories of global warming and non-renewable energy. The end-of-life phase provides limited avoided impacts. A comparative analysis quantifies the improvements achievable with an alternative type of partitions and external walls. Acronyms: AC: air conditioning; C&DW: construction and demolition waste; CFL: compact fluorescent lamp; DHW: domestic hot water; EC: European Commission; EU: European Union; GDP: gross domestic product; GHG: greenhouse gases; GWP: global warming potential; LCA: life cycle assessment; LCI: life cycle inventory; LCIA: life cycle impact assessment; MFA: material flow analysis; NREP: non-renewable energy potential; RINP: respiratory inorganics potential; WFD: Waste Framework Directive.

The Timber Resource Inventory Model (TRIM): a projection model for timber supply and policy analysis.

Science.gov (United States)

P.L. Tedder; R.N. La Mont; J.C. Kincaid

1987-01-01

TRIM (Timber Resource Inventory Model) is a yield table projection system developed for timber supply projections and policy analysis. TRIM simulates timber growth, inventories, management and area changes, and removals over the projection period. Programs in the TRIM system, card-by-card descriptions of required inputs, table formats, and sample results are presented...

Southern forest inventory and analysis volume equation user’s guide

Science.gov (United States)

Christopher M. Oswalt; Roger C. Conner

2011-01-01

Reliable volume estimation procedures are fundamental to the mission of the Forest Inventory and Analysis (FIA) program. Moreover, public access to FIA program procedures is imperative. Here we present the volume estimation procedures used by the southern FIA program of the U.S. Department of Agriculture Forest Service Southern Research Station. The guide presented...

The analysis for inventory of experimental reactor high temperature gas reactor type

International Nuclear Information System (INIS)

Sri Kuntjoro; Pande Made Udiyani

2016-01-01

Relating to the plan of the National Nuclear Energy Agency (BATAN) to operate an experimental reactor of High Temperature Gas Reactors type (RGTT), it is necessary to reactor safety analysis, especially with regard to environmental issues. Analysis of the distribution of radionuclides from the reactor into the environment in normal or abnormal operating conditions starting with the estimated reactor inventory based on the type, power, and operation of the reactor. The purpose of research is to analyze inventory terrace for Experimental Power Reactor design (RDE) high temperature gas reactor type power 10 MWt, 20 MWt and 30 MWt. Analyses were performed using ORIGEN2 computer code with high temperatures cross-section library. Calculation begins with making modifications to some parameter of cross-section library based on the core average temperature of 570 °C and continued with calculations of reactor inventory due to RDE 10 MWt reactor power. The main parameters of the reactor 10 MWt RDE used in the calculation of the main parameters of the reactor similar to the HTR-10 reactor. After the reactor inventory 10 MWt RDE obtained, a comparison with the results of previous researchers. Based upon the suitability of the results, it make the design for the reactor RDE 20MWEt and 30 MWt to obtain the main parameters of the reactor in the form of the amount of fuel in the pebble bed reactor core, height and diameter of the terrace. Based on the main parameter or reactor obtained perform of calculation to get reactor inventory for RDE 20 MWT and 30 MWT with the same methods as the method of the RDE 10 MWt calculation. The results obtained are the largest inventory of reactor RDE 10 MWt, 20 MWt and 30 MWt sequentially are to Kr group are about 1,00E+15 Bq, 1,20E+16 Bq, 1,70E+16 Bq, for group I are 6,50E+16 Bq, 1,20E+17 Bq, 1,60E+17 Bq and for groups Cs are 2,20E+16 Bq, 2,40E+16 Bq, 2,60E+16 Bq. Reactor inventory will then be used to calculate the reactor source term and it

An inventory model of purchase quantity for fully-loaded vehicles with maximum trips in consecutive transport time

Directory of Open Access Journals (Sweden)

Chen Pоуu

2013-01-01

Full Text Available Products made overseas but sold in Taiwan are very common. Regarding the cross-border or interregional production and marketing of goods, inventory decision-makers often have to think about how to determine the amount of purchases per cycle, the number of transport vehicles, the working hours of each transport vehicle, and the delivery by ground or air transport to sales offices in order to minimize the total cost of the inventory in unit time. This model assumes that the amount of purchases for each order cycle should allow all rented vehicles to be fully loaded and the transport times to reach the upper limit within the time period. The main research findings of this study included the search for the optimal solution of the integer planning of the model and the results of sensitivity analysis.

Nuclear material production cycle vulnerability analysis

International Nuclear Information System (INIS)

Bott, T.F.

1996-01-01

This paper discusses a method for rapidly and systematically identifying vulnerable equipment in a nuclear material or similar production process and ranking that equipment according to its attractiveness to a malevolent attacker. A multistep approach was used in the analysis. First, the entire production cycle was modeled as a flow diagram. This flow diagram was analyzed using graph theoretical methods to identify processes in the production cycle and their locations. Models of processes that were judged to be particularly vulnerable based on the cycle analysis then were developed in greater detail to identify equipment in that process that is vulnerable to intentional damage

An Analysis of the Optimal Multiobjective Inventory Clustering Decision with Small Quantity and Great Variety Inventory by Applying a DPSO

Science.gov (United States)

Li, Meng-Hua

2014-01-01

When an enterprise has thousands of varieties in its inventory, the use of a single management method could not be a feasible approach. A better way to manage this problem would be to categorise inventory items into several clusters according to inventory decisions and to use different management methods for managing different clusters. The present study applies DPSO (dynamic particle swarm optimisation) to a problem of clustering of inventory items. Without the requirement of prior inventory knowledge, inventory items are automatically clustered into near optimal clustering number. The obtained clustering results should satisfy the inventory objective equation, which consists of different objectives such as total cost, backorder rate, demand relevance, and inventory turnover rate. This study integrates the above four objectives into a multiobjective equation, and inputs the actual inventory items of the enterprise into DPSO. In comparison with other clustering methods, the proposed method can consider different objectives and obtain an overall better solution to obtain better convergence results and inventory decisions. PMID:25197713

Evaluation of Environmental Impacts for Rice Agroecosystems using Life Cycle Assessment (LCA)

OpenAIRE

S. Khoramdel; J. Shabahang; A. Amin Ghafouri

2017-01-01

In order to evaluate life cycle assessment (LCA) for rice agroecosystems based on mean of nitrogen fertilizer levels (less than 190, 190-200, 200-210, 210-220 and more than 220 kg N ha) during 1999-2012, an experiment was conducted. Four steps includung goal definition and scoping, inventory analysis, life cycle impact assessment and integration and interpretation were computed. Functional unit was considered as one tone paddy. Impact categories were acidification, eutrophication in aquatic a...

Emission inventory estimation of an intercity bus terminal.

Science.gov (United States)

Qiu, Zhaowen; Li, Xiaoxia; Hao, Yanzhao; Deng, Shunxi; Gao, H Oliver

2016-06-01

Intercity bus terminals are hotspots of air pollution due to concentrated activities of diesel buses. In order to evaluate the bus terminals' impact on air quality, it is necessary to estimate the associated mobile emission inventories. Since the vehicles' operating condition at the bus terminal varies significantly, conventional calculation of the emissions based on average emission factors suffers the loss of accuracy. In this study, we examined a typical intercity bus terminal-the Southern City Bus Station of Xi'an, China-using a multi-scale emission model-(US EPA's MOVES model)-to quantity the vehicle emission inventory. A representative operating cycle for buses within the station is constructed. The emission inventory was then estimated using detailed inputs including vehicle ages, operating speeds, operating schedules, and operating mode distribution, as well as meteorological data (temperature and humidity). Five functional areas (bus yard, platforms, disembarking area, bus travel routes within the station, and bus entrance/exit routes) at the terminal were identified, and the bus operation cycle was established using the micro-trip cycle construction method. Results of our case study showed that switching to compressed natural gas (CNG) from diesel fuel could reduce PM2.5 and CO emissions by 85.64 and 6.21 %, respectively, in the microenvironment of the bus terminal. When CNG is used, tail pipe exhaust PM2.5 emission is significantly reduced, even less than brake wear PM2.5. The estimated bus operating cycles can also offer researchers and policy makers important information for emission evaluation in the planning and design of any typical intercity bus terminals of a similar scale.

Life cycle inventory and carbon and water FoodPrint of fruits and vegetables: application to a Swiss retailer.

Science.gov (United States)

Stoessel, Franziska; Juraske, Ronnie; Pfister, Stephan; Hellweg, Stefanie

2012-03-20

Food production and consumption is known to have significant environmental impacts. In the present work, the life cycle assessment methodology is used for the environmental assessment of an assortment of 34 fruits and vegetables of a large Swiss retailer, with the aim of providing environmental decision-support to the retailer and establishing life cycle inventories (LCI) also applicable to other case studies. The LCI includes, among others, seedling production, farm machinery use, fuels for the heating of greenhouses, irrigation, fertilizers, pesticides, storage and transport to and within Switzerland. The results show that the largest reduction of environmental impacts can be achieved by consuming seasonal fruits and vegetables, followed by reduction of transport by airplane. Sourcing fruits and vegetables locally is only a good strategy to reduce the carbon footprint if no greenhouse heating with fossil fuels is involved. The impact of water consumption depends on the location of agricultural production. For some crops a trade-off between the carbon footprint and the induced water stress is observed. The results were used by the retailer to support the purchasing decisions and improve the supply chain management.

The impact of spent fuel reprocessing facilities deployment rate on transuranics inventory in alternative fuel cycle strategies

International Nuclear Information System (INIS)

Aquien, A.; Kazimi, M.; Hejzlar, P.

2007-01-01

The depletion rate of transuranic inventories from spent fuel depends on both the deployment of advanced reactors that can be loaded with recycled transuranics, and on the deployment of the facilities that separate and reprocess spent fuel. In addition to tracking the mass allocation of TRU in the system and calculating a system cost, the fuel cycle simulation tool CAFCA includes a flexible recycling plant deployment model. This study analyses the impact of different recycling deployment schemes for various fuel cycle strategies in the US over the next hundred years under the assumption of a demand for nuclear energy growing at a rate of 2,4%. Recycling strategies explored in this study fall under two categories: recycling in thermal light water reactors using combined non-fertile and UO 2 fuel (CONFU) and recycling in fast reactors (either fertile-free actinide burner reactors, or self-sustaining gas-cooled fast reactors). Preliminary results show that the earlier deployment of recycling in the thermal reactors will limit the stored levels of TRU below those of fast reactors. However, the avoided accumulation of spent fuel interim storage depends on the deployment rate of the recycling facilities. In addition, by the end of the mid century, the TRU in cooling storage will exceed that in interim storage. (authors)

A framework for an inventory model for deteriorating items with expiration under trapezoidal-type demand and partial backlogging

Directory of Open Access Journals (Sweden)

Kunal T. Shukla

2016-09-01

Full Text Available Background: As in the case of deteriorating items, expiration plays a major role in inventory management, a generalized approach is studied based on an inventory model for deteriorating items with expiration dates. Methods: In this paper, the demand rate during the cycle time is assumed to be trapezoidal. Shortages are allowed and partially backlogged. An inventory replenishment strategy is formulated for trapezoidal demand rates and backlogging rates in general for retailers; with the support of fundamental concepts of calculus. Results: The method is illustrated with the support of numerical examples along with sensitivity analysis with respect to major parameters. Conclusion: This generalized approach provides a platform to develop a strategy using different demand functions and backlogging rates.

An Analysis of the Impact of RFID Technology on Inventory Systems

Science.gov (United States)

Rekik, Yacine

Nowadays, most enterprises undertake large investments in order to implement information systems that support decision making for managing inventories. Nevertheless, if data collected from the physical processes used to feed these systems are not correct, there will be severe impacts on business performance. Inventory inaccuracy occurs when the inventory level in the Information System is not in agreement with the physically available inventory. In this chapter, we first describe the major factors generating inventory inaccuracy. Then, we provide situations permitting to manage an inventory system subject to errors. We provide a framework to model the inventory inaccuracy issue and focus on the impact of advanced identification systems, such as that provided by RFID technology, in improving the performance of a supply chain subject to inventory inaccuracies.

Optimization of inventory management in furniture manufacturing

OpenAIRE

Karkauskas, Justinas

2017-01-01

Aim of research - to present inventory management optimization guidelines for furniture manufacturing company, based on analysis of scientific literature and empirical research. Tasks of the Issue: • Disclose problems of inventory management in furniture manufacturing sector; • To analyze theoretical inventory management decisions; • To develop theoretical inventory management optimization model; • Do empirical research of inventory management and present offers for optimizatio...

Results of the 1988 Baden-Wuerttemberg stress inventory

International Nuclear Information System (INIS)

Hildebrand, E.E.; Schoepfer, W.; Hanack, C.; Kublin, E.; Trefz-Malcher, G.

1993-01-01

As a comparison of the 1983 and 1988 needle-analysis inventories showed, Mg and K deficiency situations, in particular, and conditions of inadequate calcium supply tend to persist and were clearly to be distinguished from fluctuations due to weather during the five-year observation period. Obviously, therefore, a complete, lasting recovery of the nutrition situation in such regions without aimed interventions is rather unlikely. Restoring stable nutritive element cycles will also in the future require application of nutritive elements and buffer substances as part of site-specific melioration measures. Sulfur contents show for the greater part a decreasing tend, which indicates a generally reduced deposition of this element. (orig./EF) [de

Gridded anthropogenic emissions inventory and atmospheric transport of carbonyl sulfide in the U.S.: U.S. Anthropogenic COS Source and Transport

Energy Technology Data Exchange (ETDEWEB)

Zumkehr, Andrew [Sierra Nevada Research Institute, University of California, Merced California USA; Hilton, Timothy W. [Sierra Nevada Research Institute, University of California, Merced California USA; Whelan, Mary [Sierra Nevada Research Institute, University of California, Merced California USA; Smith, Steve [Joint Global Change Research Institute, PNNL, College Park Maryland USA; Campbell, J. Elliott [Sierra Nevada Research Institute, University of California, Merced California USA

2017-02-21

Carbonyl sulfide (COS or OCS), the most abundant sulfur containing gas in the troposphere, has recently emerged as a potentially important atmospheric tracer for the carbon cycle. Atmospheric inverse modeling studies may be able to use existing tower, airborne, and satellite observations of COS to infer information about photosynthesis. However, such analysis relies on gridded anthropogenic COS source estimates that are largely based on industry activity data from over three decades ago. Here we use updated emission factor data and industry activity data to develop a gridded inventory with a 0.1 degree resolution for the U.S. domain. The inventory includes the primary anthropogenic COS sources including direct emissions from the coal and aluminum industries as well as indirect sources from industrial carbon disulfide emissions. Compared to the previously published inventory, we found that the total anthropogenic source (direct and indirect) is 47% smaller. Using this new gridded inventory to drive the STEM/WRF atmospheric transport model, we found that the anthropogenic contribution to COS variation in the troposphere is small relative to the biosphere influence, which is encouraging of carbon cycle applications in this region. Additional anthropogenic sectors with highly uncertain emission factors require further field measurements.

Modelling the inventory and impact assessment of partitioning and transmutation approaches to spent nuclear fuel management

International Nuclear Information System (INIS)

Hoggett-Jones, C.; Robbins, C.; Gettinby, G.; Blythe, S.

2002-01-01

An inventory modelling and impact assessment system to investigate the potential effects of partitioning and transmutation is proposed. It is founded on a mass based inventory analysis using the principles of basic nuclear physics and the international standards for assessing radiological health effects. It is specific to the back-end of the nuclear fuel cycle and is applied to four alternative spent fuel management strategies. The system accounts for the dynamic nature of post-irradiation scenarios and is being used to develop software for use within the nuclear power industry. Four example waste-disposal options are considered using the method. Impact assessments and parameter sensitivity analyses are presented

Modelling the inventory and impact assessment of partitioning and transmutation approaches to spent nuclear fuel management

Energy Technology Data Exchange (ETDEWEB)

Hoggett-Jones, C. E-mail: craig@stams.strath.ac.uk; Robbins, C.; Gettinby, G.; Blythe, S

2002-03-01

An inventory modelling and impact assessment system to investigate the potential effects of partitioning and transmutation is proposed. It is founded on a mass based inventory analysis using the principles of basic nuclear physics and the international standards for assessing radiological health effects. It is specific to the back-end of the nuclear fuel cycle and is applied to four alternative spent fuel management strategies. The system accounts for the dynamic nature of post-irradiation scenarios and is being used to develop software for use within the nuclear power industry. Four example waste-disposal options are considered using the method. Impact assessments and parameter sensitivity analyses are presented.

Study of Intelligent Secure Chemical Inventory Management System

Science.gov (United States)

Shukran, Mohd Afizi Mohd; Naim Abdullah, Muhammad; Nazri Ismail, Mohd; Maskat, Kamaruzaman; Isa, Mohd Rizal Mohd; Shahfee Ishak, Muhammad; Adib Khairuddin, Muhamad

2017-08-01

Chemical inventory management system has been experiencing a new revolution from traditional inventory system which is manual to an automated inventory management system. In this paper, some review of the classic and modern approaches to chemical inventory management system has been discussed. This paper also describe about both type of inventory management. After a comparative analysis of the traditional method and automated method, it can be said that both methods have some distinctive characteristics. Moreover, the automated inventory management method has higher accuracy of calculation because the calculations are handled by software, eliminating possible errors and saving time. The automated inventory system also allows users and administrators to track the availability, location and consumption of chemicals. The study of this paper can provide forceful review analysis support for the chemical inventory management related research.

Projecting Timber Inventory at the Product Level

Science.gov (United States)

Lawrence Teeter; Xiaoping Zhou

1999-01-01

Current timber inventory projections generally lack information on inventory by product classes. Most models available for inventory projection and linked to supply analyses are limited to projecting aggregate softwood and hardwood. The research presented describes a methodology for distributing the volume on each FIA (USDA Forest Service Forest Inventory and Analysis...

Analysis within the systems development life-cycle

CERN Document Server

Rock-Evans, Rosemary

1987-01-01

Analysis within the Systems Development Life-Cycle: Book 2, Data Analysis-The Methods describes the methods for carrying out data analysis within the systems development life-cycle and demonstrates how the results of fact gathering can be used to produce and verify the analysis deliverables. A number of alternative methods of analysis other than normalization are suggested. Comprised of seven chapters, this book shows the tasks to be carried out in the logical order of progression-preparation, collection, analysis of the existing system (which comprises the tasks of synthesis, verification, an

Inventory on cleaner production education and training

DEFF Research Database (Denmark)

Jørgensen, Michael Søgaard; Pöyry, Sirkka; Huisingh, Donald

Analysis and presentation of the data from an international inventory on cleaner production education and training......Analysis and presentation of the data from an international inventory on cleaner production education and training...

Assessment of drought related mortality in pinyon-juniper and ponderosa pine forests using Forest Inventory and Analysis data

Science.gov (United States)

John D. Shaw

2008-01-01

(Please note, this is an abstract only) Widespread mortality in several forest types is associated with several years of drought in the Southwest. Implementation of USDA Forest Service Forest Inventory and Analysis (FIA) annual inventory in several states coincided with the onset of elevated mortality rates. Analysis of data collected 2000-2004 reveals the status and...

Fuel cell hybrid taxi life cycle analysis

Energy Technology Data Exchange (ETDEWEB)

Baptista, Patricia, E-mail: patricia.baptista@ist.utl.pt [IDMEC-Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1, 1049-001 Lisboa (Portugal); Ribau, Joao; Bravo, Joao; Silva, Carla [IDMEC-Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1, 1049-001 Lisboa (Portugal); Adcock, Paul; Kells, Ashley [Intelligent Energy, Charnwood Building, HolywellPark, Ashby Road, Loughborough, LE11 3GR (United Kingdom)

2011-09-15

A small fleet of classic London Taxis (Black cabs) equipped with hydrogen fuel cell power systems is being prepared for demonstration during the 2012 London Olympics. This paper presents a Life Cycle Analysis for these vehicles in terms of energy consumption and CO{sub 2} emissions, focusing on the impacts of alternative vehicle technologies for the Taxi, combining the fuel life cycle (Tank-to-Wheel and Well-to-Tank) and vehicle materials Cradle-to-Grave. An internal combustion engine diesel taxi was used as the reference vehicle for the currently available technology. This is compared to battery and fuel cell vehicle configurations. Accordingly, the following energy pathways are compared: diesel, electricity and hydrogen (derived from natural gas steam reforming). Full Life Cycle Analysis, using the PCO-CENEX drive cycle, (derived from actual London Taxi drive cycles) shows that the fuel cell powered vehicle configurations have lower energy consumption (4.34 MJ/km) and CO{sub 2} emissions (235 g/km) than both the ICE Diesel (9.54 MJ/km and 738 g/km) and the battery electric vehicle (5.81 MJ/km and 269 g/km). - Highlights: > A Life Cycle Analysis of alternative vehicle technologies for the London Taxi was performed. > The hydrogen powered vehicles have the lowest energy consumption and CO{sub 2} emissions results. > A hydrogen powered solution can be a sustainable alternative in a full life cycle framework.

Fuel cell hybrid taxi life cycle analysis

International Nuclear Information System (INIS)

Baptista, Patricia; Ribau, Joao; Bravo, Joao; Silva, Carla; Adcock, Paul; Kells, Ashley

2011-01-01

A small fleet of classic London Taxis (Black cabs) equipped with hydrogen fuel cell power systems is being prepared for demonstration during the 2012 London Olympics. This paper presents a Life Cycle Analysis for these vehicles in terms of energy consumption and CO 2 emissions, focusing on the impacts of alternative vehicle technologies for the Taxi, combining the fuel life cycle (Tank-to-Wheel and Well-to-Tank) and vehicle materials Cradle-to-Grave. An internal combustion engine diesel taxi was used as the reference vehicle for the currently available technology. This is compared to battery and fuel cell vehicle configurations. Accordingly, the following energy pathways are compared: diesel, electricity and hydrogen (derived from natural gas steam reforming). Full Life Cycle Analysis, using the PCO-CENEX drive cycle, (derived from actual London Taxi drive cycles) shows that the fuel cell powered vehicle configurations have lower energy consumption (4.34 MJ/km) and CO 2 emissions (235 g/km) than both the ICE Diesel (9.54 MJ/km and 738 g/km) and the battery electric vehicle (5.81 MJ/km and 269 g/km). - Highlights: → A Life Cycle Analysis of alternative vehicle technologies for the London Taxi was performed. → The hydrogen powered vehicles have the lowest energy consumption and CO 2 emissions results. → A hydrogen powered solution can be a sustainable alternative in a full life cycle framework.

The thorium fuel cycle in water-moderated reactor systems

International Nuclear Information System (INIS)

Critoph, E.

1977-05-01

Thorium and uranium cycles are compared with regard to reactor characteristics and technology, fuel-cycle technology, economic parameters, fuel-cycle costs, and system characteristics. In heavy-water reactors (HWRs) thorium cycles having uranium requirements at equilibrium ranging from zero to a quarter of those for the natural-uranium once-through cycle appear feasible. An 'inventory' of uranium of between 1 and 2 Mg/MW(e) is required for the transition to equilibrium. The cycles with the lowest uranium requirements compete with the others only at high uranium prices. Using thorium in light-water reactors, uranium requirements can be reduced by a factor of between two and three from the once-through uranium cycle. The light-water breeder reactor, promising zero uranium requirements at equilibrium, is being developed. Larger uranium inventories are required than for the HWRs. The lead time, from a decision to use thorium to significant impact on uranium utilization (compared to uranium cycle, recycling plutonium) is some two decades

Presentation and Analysis of a Worldwide Database of Earthquake-Induced Landslide Inventories : Earthquake-Induced Landslide Inventories

NARCIS (Netherlands)

Tanyas, Hakan; Van Westen, Cees J.; Allstadt, Kate E.; Anna Nowicki Jessee, M.; Görüm, Tolga; Jibson, Randall W.; Godt, Jonathan W.; Sato, Hiroshi P.; Schmitt, Robert G.; Marc, Odin; Hovius, Niels

2017-01-01

Earthquake‐induced landslide (EQIL) inventories are essential tools to extend our knowledge of the relationship between earthquakes and the landslides they can trigger. Regrettably, such inventories are difficult to generate and therefore scarce, and the available ones differ in terms of their

The Life Cycle Analysis Toolbox

International Nuclear Information System (INIS)

Bishop, L.; Tonn, B.E.; Williams, K.A.; Yerace, P.; Yuracko, K.L.

1999-01-01

The life cycle analysis toolbox is a valuable integration of decision-making tools and supporting materials developed by Oak Ridge National Laboratory (ORNL) to help Department of Energy managers improve environmental quality, reduce costs, and minimize risk. The toolbox provides decision-makers access to a wide variety of proven tools for pollution prevention (P2) and waste minimization (WMin), as well as ORNL expertise to select from this toolbox exactly the right tool to solve any given P2/WMin problem. The central element of the toolbox is a multiple criteria approach to life cycle analysis developed specifically to aid P2/WMin decision-making. ORNL has developed numerous tools that support this life cycle analysis approach. Tools are available to help model P2/WMin processes, estimate human health risks, estimate costs, and represent and manipulate uncertainties. Tools are available to help document P2/WMin decision-making and implement programs. Tools are also available to help track potential future environmental regulations that could impact P2/WMin programs and current regulations that must be followed. An Internet-site will provide broad access to the tools

Decay profiles of {beta} and {gamma} for a radionuclide inventory in equilibrium cycle of a BWR type reactor; Perfiles de decaimiento de radiacion {beta} y {gamma} para un inventario de radionuclidos en ciclo de equilibrio de un reactor tipo BWR

Energy Technology Data Exchange (ETDEWEB)

Salaices, M.; Sandoval, S.; Ovando, R. [Instituto de Investigaciones Electricas. Gerencia de Energia Nuclear, Av. Reforma 113 Col. Palmira. 62490 Cuernavaca, Morelos (Mexico)]. e-mail: sal@iie.org.mx

2007-07-01

Presently work the {beta} and {gamma} radiation decay profiles for a radionuclides inventory in equilibrium cycle of a BWR type reactor is presented. The profiles are presented in terms of decay in the activity of the total inventory as well as of the chemical groups that conform the inventory. In the obtaining of the radionuclides inventory in equilibrium cycle the ORIGEN2 code, version 1 was used, which simulates fuel burnup cycles and it calculates the evolution of the isotopic composition as a result of the burnt one, irradiation and decay of the nuclear fuel. It can be observed starting from the results that the decrease in the activity for the initial inventory and the different chemical groups that conform it is approximately proportional to the base 10 logarithm of the time for the first 24 hours of having concluded the burnt one. It can also be observed that the chemical groups that contribute in more proportion to the total activity of the inventory are the lanthanides-actinides and the transition metals, with 39% and 28%, respectively. The groups of alkaline earth metals, halogens, metalloids, noble gases and alkaline metals, contribute with percentages that go from the 8 to 5%. The groups that less they contribute to the total activity of the inventory they are the non metals and semi-metals with smaller proportions that 1%. The chemical groups that more contribute to the energy of {beta} and {gamma} radiation its are the transition metals and the lanthanides-actinides with a change in the order of importance at the end of the 24 hours period. The case of the halogens is of relevance for the case of the {gamma} radiation energy due that occupying the very near third site to the dimensions of the two previous groups. Additionally, the decay in the activity for the total inventory and the groups that conform it can be simulated by means of order 6 polynomials or smaller than describe its behavior appropriately. The results presented in this work, coupled

Uranium oxide fuel cycle analysis in VVER-1000 with VISTA simulation code

Science.gov (United States)

Mirekhtiary, Seyedeh Fatemeh; Abbasi, Akbar

2018-02-01

The VVER-1000 Nuclear power plant generates about 20-25 tons of spent fuel per year. In this research, the fuel transmutation of Uranium Oxide (UOX) fuel was calculated by using of nuclear fuel cycle simulation system (VISTA) code. In this simulation, we evaluated the back end components fuel cycle. The back end component calculations are Spent Fuel (SF), Actinide Inventory (AI) and Fission Product (FP) radioisotopes. The SF, AI and FP values were obtained 23.792178 ton/y, 22.811139 ton/y, 0.981039 ton/y, respectively. The obtained value of spent fuel, major actinide, and minor actinide and fission products were 23.8 ton/year, 22.795 ton/year, 0.024 ton/year and 0.981 ton/year, respectively.

Effects of inflation and time value of money on an inventory system with deteriorating items and partially backlogged shortages

Directory of Open Access Journals (Sweden)

Chandra K. Jaggi

2016-04-01

Full Text Available As the long arm of the grinding, deep financial crisis continues to haunt the global economy, the effects of inflation and time value of money cannot be oblivious to an inventory system. Inflation, defined as a general rise in the prices of goods and services over a period of time, has monetary depreciation as one of its major side effects. And, since inventories correspond to substantial investment in capital for any organization, it would be unethical if the effects of inflation and time value of money are not considered while determining the optimal inventory policy. Moreover, deterioration of items is a phenomenon which cannot be ignored, as it may yield misleading results. Further, under the inflationary conditions, the different cost parameters including the price are bound to vary from cycle to cycle over the planning horizon. Another important factor is shortages which no retailer would prefer, and in practice are partially backlogged and partially lost. In order to convert the lost sales into sales, the retailer offers such customers an incentive, by charging them the price prevailing at the time of placing an order, instead of the current inflated price. Therefore, bearing in mind these facts, the present paper develops an inventory model for a retailer dealing with deteriorating items under inflationary conditions over a fixed planning horizon. The objective is to derive the optimal number of cycles and cycle length that maximizes the net present value of the total profit over a fixed planning horizon. An appropriate algorithm has been proposed to obtain the optimal solution. Finally, a numerical example is provided to illustrate the proposed model. Sensitivity analysis of the optimal solution with respect to major parameters is carried out and some managerial inferences have been presented.

Analysis within the systems development life-cycle

CERN Document Server

Rock-Evans, Rosemary

1987-01-01

Analysis within the Systems Development Life-Cycle: Book 4, Activity Analysis-The Methods describes the techniques and concepts for carrying out activity analysis within the systems development life-cycle. Reference is made to the deliverables of data analysis and more than one method of analysis, each a viable alternative to the other, are discussed. The """"bottom-up"""" and """"top-down"""" methods are highlighted. Comprised of seven chapters, this book illustrates how dependent data and activities are on each other. This point is especially brought home when the task of inventing new busin

Background qualitative analysis of the European reference life cycle database (ELCD) energy datasets - part II: electricity datasets.

Science.gov (United States)

Garraín, Daniel; Fazio, Simone; de la Rúa, Cristina; Recchioni, Marco; Lechón, Yolanda; Mathieux, Fabrice

2015-01-01

The aim of this paper is to identify areas of potential improvement of the European Reference Life Cycle Database (ELCD) electricity datasets. The revision is based on the data quality indicators described by the International Life Cycle Data system (ILCD) Handbook, applied on sectorial basis. These indicators evaluate the technological, geographical and time-related representativeness of the dataset and the appropriateness in terms of completeness, precision and methodology. Results show that ELCD electricity datasets have a very good quality in general terms, nevertheless some findings and recommendations in order to improve the quality of Life-Cycle Inventories have been derived. Moreover, these results ensure the quality of the electricity-related datasets to any LCA practitioner, and provide insights related to the limitations and assumptions underlying in the datasets modelling. Giving this information, the LCA practitioner will be able to decide whether the use of the ELCD electricity datasets is appropriate based on the goal and scope of the analysis to be conducted. The methodological approach would be also useful for dataset developers and reviewers, in order to improve the overall Data Quality Requirements of databases.

Configuration model of partial repairable spares under batch ordering policy based on inventory state

Institute of Scientific and Technical Information of China (English)

Ruan Minzhi; Luo Yi; Li Hua

2014-01-01

Rational planning of spares configuration project is an effective approach to improve equipment availability as well as reduce life cycle cost (LCC). With an analysis of various impacts on support system, the spares demand rate forecast model is constructed. According to systemic analysis method, spares support effectiveness evaluation indicators system is built, and then, initial spares configuration and optimization method is researched. To the issue of discarding and con-sumption for incomplete repairable items, its expected backorders function is approximated by Laplace demand distribution. Combining the (s-1, s) and (R, Q) inventory policy, the spares resup-ply model is established under the batch ordering policy based on inventory state, and the optimi-zation analysis flow for spares configuration is proposed. Through application on shipborne equipment spares configuration, the given scenarios are analyzed under two constraint targets:one is the support effectiveness, and the other is the spares cost. Analysis reveals that the result is consistent with practical regulation;therefore, the model’s correctness, method’s validity as well as optimization project’s rationality are proved to a certain extent.

Analysis of a combined Rankine-vapour-compression refrigeration cycle

International Nuclear Information System (INIS)

Aphornratana, Satha; Sriveerakul, Thanarath

2010-01-01

This paper describes a theoretical analysis of a heat-powered refrigeration cycle, a combined Rankine-vapour-compression refrigeration cycle. This refrigeration cycle combines an Organic Rankine Cycle and a vapour-compression cycle. The cycle can be powered by low grade thermal energy as low as 60 deg. C and can produce cooling temperature as low as -10 deg. C. In the analysis, two combined Rankine-vapour-compression refrigeration cycles were investigated: the system with R22 and the system with R134a. Calculated COP values between 0.1 and 0.6 of both the systems were found.

Development of fusion fuel cycles: Large deviations from US defense program systems

Energy Technology Data Exchange (ETDEWEB)

Klein, James Edward, E-mail: james.klein@srnl.doe.gov; Poore, Anita Sue; Babineau, David W.

2015-10-15

Highlights: • All tritium fuel cycles start with a “Tritium Process.” All have similar tritium processing steps. • Fusion tritium fuel cycles minimize process tritium inventories for various reasons. • US defense program facility designs did not minimize in-process inventories. • Reduced inventory tritium facilities will lower public risk. - Abstract: Fusion energy research is dominated by plasma physics and materials technology development needs with smaller levels of effort and funding dedicated to tritium fuel cycle development. The fuel cycle is necessary to supply and recycle tritium at the required throughput rate; additionally, tritium confinement throughout the facility is needed to meet regulatory and environmental release limits. Small fuel cycle development efforts are sometimes rationalized by stating that tritium processing technology has already been developed by nuclear weapons programs and these existing processes only need rescaling or engineering design to meet the needs of fusion fuel cycles. This paper compares and contrasts features of tritium fusion fuel cycles to United States Cold War era defense program tritium systems. It is concluded that further tritium fuel cycle development activities are needed to provide technology development beneficial to both fusion and defense programs tritium systems.

An Analysis of the Order Cycle at Coast Guard Supply Center Curtis Bay, Maryland. How to Measure Customer Service.

Science.gov (United States)

1994-12-01

Order Cycle ..... 20 2. Order Processing and the Information System .......... ................. 21 3. The Order Cycle at SCCB ...... ......... 21 v...order transmittal time, order processing time, order assembly time, stock availability, production time, and delivery time. CUSTOMER L7 2 I i u *r1...methods, inventory stocking policies, order processing procedures, transport modes, and scheduling methods [Ref. 15]. 20 2. Order Processing and the

National inventory of the radioactive wastes and the recycling materials; Inventaire national des dechets radioactifs et des matieres valorisables

Energy Technology Data Exchange (ETDEWEB)

Dupuis, M.C

2006-07-01

This synthesis report presents the 2006 inventory of the radioactive wastes and recycling materials, in France. It contains 9 chapters: a general introduction, the radioactive wastes (definition, classification, origins and management), the inventory methodology (organization, accounting and prospecting, exhaustiveness and control tools), main results (stocks, prevision for the period 2005-2020, perspectives after 2020), the inventory for producers or owners (front end fuel cycle, electric power plants, back end fuel cycle, wastes processing and maintenance facilities, researches centers, medical activities, industrial activities, non nuclear industries using nuclear materials, defense center, storage and disposal), the polluted sites, examples of foreign inventories, conclusion and annexes. (A.L.B.)

The application methods of ABC/XYZ-analysis for the inventory management purposes within the ERP-system

Directory of Open Access Journals (Sweden)

O. V. Zhukov

2017-01-01

Full Text Available Inventory management for a trading company is a vital task, which requires processing significant amounts of information. Through the application of ABC/XYZ-analysis of the nomenclature within the enterprise ERP-system, it is possible to increase significantly the efficiency of inventory management, in accordance with Pareto principle concentrating on managing the most important categories of goods. Various researchers dealt with the methods of ABC/XYZ-analysis itself but its usage as a part of the inventory management and procurement subsystem has a number of essential features, ignoring of which can lead to tangible negative consequences. The article discusses the methods and key problems of application of ABC/XYZ-analysis within the enterprise management accounting information system. For each of the factors that can affect the reliability of sales and procurement statistics and distort the results of the classification of goods, we have formulated the proposals to minimize the negative impact of that specific factor. Proposed methods allow reducing the impact of the following factors: availability of conditions for duplicate nomenclature to appear within the enterprise accounting software, the lack of a unified approach to the formation of names for newly created items of nomenclature, frequent changes in the products range of the suppliers, excessive detailing of information about a product in its name. The results of successfully implemented analysis and classification of goods can be used for a wide range of tasks varying from implementing effective inventory control to general planning and forecasting commodity flows as a part of the enterprise budgeting model. Solving these problems will harmoniously fit the inventory management in the managerial accounting system making it an effective tool in achieving strategic business goals.

Analysis of Maisotsenko open gas turbine bottoming cycle

International Nuclear Information System (INIS)

Saghafifar, Mohammad; Gadalla, Mohamed

2015-01-01

Maisotsenko gas turbine cycle (MGTC) is a recently proposed humid air turbine cycle. An air saturator is employed for air heating and humidification purposes in MGTC. In this paper, MGTC is integrated as the bottoming cycle to a topping simple gas turbine as Maisotsenko bottoming cycle (MBC). A thermodynamic optimization is performed to illustrate the advantages and disadvantages of MBC as compared with air bottoming cycle (ABC). Furthermore, detailed sensitivity analysis is reported to present the effect of different operating parameters on the proposed configurations' performance. Efficiency enhancement of 3.7% is reported which results in more than 2600 tonne of natural gas fuel savings per year. - Highlights: • Developed an accurate air saturator model. • Introduced Maisotsenko bottoming cycle (MBC) as a power generation cycle. • Performed Thermodynamic optimization for MBC and air bottoming cycle (ABC). • Performed detailed sensitivity analysis for MBC under different operating conditions. • MBC has higher efficiency and specific net work output as compared to ABC

Nuclear fuel cycle system simulation tool based on high-fidelity component modeling

Energy Technology Data Exchange (ETDEWEB)

Ames, David E.,

2014-02-01

The DOE is currently directing extensive research into developing fuel cycle technologies that will enable the safe, secure, economic, and sustainable expansion of nuclear energy. The task is formidable considering the numerous fuel cycle options, the large dynamic systems that each represent, and the necessity to accurately predict their behavior. The path to successfully develop and implement an advanced fuel cycle is highly dependent on the modeling capabilities and simulation tools available for performing useful relevant analysis to assist stakeholders in decision making. Therefore a high-fidelity fuel cycle simulation tool that performs system analysis, including uncertainty quantification and optimization was developed. The resulting simulator also includes the capability to calculate environmental impact measures for individual components and the system. An integrated system method and analysis approach that provides consistent and comprehensive evaluations of advanced fuel cycles was developed. A general approach was utilized allowing for the system to be modified in order to provide analysis for other systems with similar attributes. By utilizing this approach, the framework for simulating many different fuel cycle options is provided. Two example fuel cycle configurations were developed to take advantage of used fuel recycling and transmutation capabilities in waste management scenarios leading to minimized waste inventories.

Forest inventory and analysis program in the Western U.S.

Science.gov (United States)

Ashley. Lehman

2015-01-01

The Pacific Northwest (PNW) Research Station’s Forest Inventory and Analysis (FIA) program of the USDA Forest Service monitors and reports on the status and trends of the Pacific Island’s forest resources and ecosystem services. Since 2001 the FIA program has partnered with State and Private Forestry’s, Region 5 and the local governments in the U.S. Affiliated Western...

Life-cycle analysis of renewable energy systems

DEFF Research Database (Denmark)

Sørensen, Bent

1994-01-01

An imlementation of life-cycle analysis (LCA) for energy systems is presented and applied to two renewable energy systems (wind turbines and building-integrated photovoltaic modules) and compared with coal plants......An imlementation of life-cycle analysis (LCA) for energy systems is presented and applied to two renewable energy systems (wind turbines and building-integrated photovoltaic modules) and compared with coal plants...

Analysis within the systems development life-cycle

CERN Document Server

Rock-Evans, Rosemary

1987-01-01

Analysis within the Systems Development Life-Cycle, Book 3: Activity Analysis - The Deliverables provides a comprehensive coverage of the deliverables of activity analysis. The book also details purpose of each deliverable in the context of the next tasks in the systems development cycle (SDC). The text first covers the concept of deliverables and the benefits of making deliverables visible. In the second chapter, the book introduces the main concepts and diagrammatic techniques of activity analysis. The third chapter deals with the important classes or categories of concept, while the fourth

A Rasch Analysis of the Junior Metacognitive Awareness Inventory with Singapore Students

Science.gov (United States)

Ning, Hoi Kwan

2018-01-01

The psychometric properties of the 2 versions of the Junior Metacognitive Awareness Inventory were examined with Singapore student samples. Other than 2 misfitting items and an underutilized response scale, Rasch analysis demonstrated that the instruments have good measurement precision, and no differential item functioning was detected across…

Analysis of environmental impact phase in the life cycle of a nuclear power plant; Analisis de la fase de impacto ambiental en el ciclo de vida de una central nuclear

Energy Technology Data Exchange (ETDEWEB)

Hernandez del M, C.

2015-07-01

The life-cycle analysis covers the environmental aspects of a product throughout its life cycle. The focus of this study was to apply a methodology of life-cycle analysis for the environmental impact assessment of a nuclear power plant by analyzing international standards ISO 14040 and 14044. The methodology of life-cycle analysis established by the ISO 14044 standard was analyzed, as well as the different impact assessment methodologies of life cycle in order to choose the most appropriate for a nuclear power plant; various tools for the life-cycle analysis were also evaluated, as is the use of software and the use of databases to feed the life cycle inventory. The functional unit chosen was 1 KWh of electricity, the scope of analysis ranging from the construction and maintenance, disposal of spent fuel to the decommissioning of the plant, the manufacturing steps of the fuel were excluded because in Mexico is not done this stage. For environmental impact assessment was chosen the Recipe methodology which evaluates up to 18 impact categories depending on the project. In the case of a nuclear power plant were considered only categories of depletion of the ozone layer, climate change, ionizing radiation and formation of particulate matter. The different tools for life-cycle analysis as the methodologies of impact assessment of life cycle, different databases or use of software have been taken according to the modeling of environmental sensitivities of different regions, because in Mexico the methodology for life-cycle analysis has not been studied and still do not have all the tools necessary for the evaluation, so the uncertainty of the data supplied and results could be higher. (Author)

The status of nuclear fuel cycle system analysis for the development of advanced nuclear fuel cycles

Energy Technology Data Exchange (ETDEWEB)

Ko, Won Il; Kim, Seong Ki; Lee, Hyo Jik; Chang, Hong Rae; Kwon, Eun Ha; Lee, Yoon Hee; Gao, Fanxing [KAERI, Daejeon (Korea, Republic of)

2011-11-15

The system analysis has been used with different system and objectives in various fields. In the nuclear field, the system can be applied from uranium mining to spent fuel reprocessing or disposal which is called the nuclear fuel cycle. The analysis of nuclear fuel cycle can be guideline for development of advanced fuel cycle through integrating and evaluating the technologies. For this purpose, objective approach is essential and modeling and simulation can be useful. In this report, several methods which can be applicable for development of advanced nuclear fuel cycle, such as TRL, simulation and trade analysis were explained with case study

Accounting for the biogeochemical cycle of nitrogen in input-output life cycle assessment.

Science.gov (United States)

Singh, Shweta; Bakshi, Bhavik R

2013-08-20

Nitrogen is indispensable for sustaining human activities through its role in the production of food, animal feed, and synthetic chemicals. This has encouraged significant anthropogenic mobilization of reactive nitrogen and its emissions into the environment resulting in severe disruption of the nitrogen cycle. This paper incorporates the biogeochemical cycle of nitrogen into the 2002 input-output model of the U.S. economy. Due to the complexity of this cycle, this work proposes a unique classification of nitrogen flows to facilitate understanding of the interaction between economic activities and various flows in the nitrogen cycle. The classification scheme distinguishes between the mobilization of inert nitrogen into its reactive form, use of nitrogen in various products, and nitrogen losses to the environment. The resulting inventory and model of the US economy can help quantify the direct and indirect impacts or dependence of economic sectors on the nitrogen cycle. This paper emphasizes the need for methods to manage the N cycle that focus not just on N losses, which has been the norm until now, but also include other N flows for a more comprehensive view and balanced decisions. Insight into the N profile of various sectors of the 2002 U.S. economy is presented, and the inventory can also be used for LCA or Hybrid LCA of various products. The resulting model is incorporated in the approach of Ecologically-Based LCA and available online.

Safety analysis and inventory control of transuranic and low-level waste in common storage

International Nuclear Information System (INIS)

Porten, D.R.; Bonner, A.L.; Joyce, J.P.

1993-01-01

This paper describes a methodology developed For the inventory control of low-level waste (LLW) and transuranic (TRU) waste, when both are stored in the same location, and both contribute to an inventory constrained by safety considerations. Development of the method arose from the necessity to make safety analysis calculations for the addition of LLW, in quantities greater than existing inventory limits would allow when stored with TRU waste, in the Hanford Central Waste Complex (CWC)-Ensuring that the dose consequences of credible releases are maintained at low-hazard limits or less, was used to allow greater than Type A quantities of LLW into the CWC. Basically, what happens is the original limited amount of TRU allowed is reduced by some equivalent amount of LLW introduced. The total quantity of TRU, and LLW in excess of Type A quantities, must be administratively maintained via curie equivalency Factors to ensure operation as a low-hazard Facility. The ''equivalency'' between TRU and LLW proposed here is specific only to the CWC, but the methodology can be used for other specific applications, such as TRU and LLW storage or handling facilities where inventory limits must be enforced or where a simplified inventory system is required

Economic Analysis of Several Nuclear Fuel Cycles

International Nuclear Information System (INIS)

Ko, Won Il; Gao, Fanxing; Kim, Sung Ki

2012-01-01

Economics is one of the essential criteria to be considered for the future deployment of the nuclear power. With regard to the competitive power market, the cost of electricity from nuclear power plants is somewhat highly competitive with those from the other electricity generations, averaging lower in cost than fossil fuels, wind, or solar. However, a closer look at the nuclear power production brings an insight that the cost varies within a wide range, highly depending on a nuclear fuel cycle option. The option of nuclear fuel cycle is a key determinant in the economics, and therefrom, a comprehensive comparison among the proposed fuel cycle options necessitates an economic analysis for thirteen promising options based on the material flow analysis obtained by an equilibrium model as specified in the first article (Modeling and System Analysis of Different Fuel Cycle Options for Nuclear Power Sustainability (I): Uranium Consumption and Waste Generation). The objective of the article is to provide a systematic cost comparison among these nuclear fuel cycles. The generation cost (GC) generally consists of a capital cost, an operation and maintenance cost (O and M cost), a fuel cycle cost (FCC), and a decontaminating and decommissioning (D and D) cost. FCC includes a frontend cost and a back-end cost, as well as costs associated with fuel recycling in the cases of semi-closed and closed cycle options. As a part of GC, the economic analysis on FCC mainly focuses on the cost differences among fuel cycle options considered and therefore efficiently avoids the large uncertainties of the Generation-IV reactor capital costs and the advanced reprocessing costs. However, the GC provides a more comprehensive result covering all the associated costs, and therefrom, both GC and FCC have been analyzed, respectively. As a widely applied tool, the levelized cost (mills/KWh) proves to be a fundamental calculation principle in the energy and power industry, which is particularly

Evaluation of pavement life cycle cost analysis: Review and analysis

Directory of Open Access Journals (Sweden)

Peyman Babashamsi

2016-07-01

Full Text Available The cost of road construction consists of design expenses, material extraction, construction equipment, maintenance and rehabilitation strategies, and operations over the entire service life. An economic analysis process known as Life-Cycle Cost Analysis (LCCA is used to evaluate the cost-efficiency of alternatives based on the Net Present Value (NPV concept. It is essential to evaluate the above-mentioned cost aspects in order to obtain optimum pavement life-cycle costs. However, pavement managers are often unable to consider each important element that may be required for performing future maintenance tasks. Over the last few decades, several approaches have been developed by agencies and institutions for pavement Life-Cycle Cost Analysis (LCCA. While the transportation community has increasingly been utilising LCCA as an essential practice, several organisations have even designed computer programs for their LCCA approaches in order to assist with the analysis. Current LCCA methods are analysed and LCCA software is introduced in this article. Subsequently, a list of economic indicators is provided along with their substantial components. Collecting previous literature will help highlight and study the weakest aspects so as to mitigate the shortcomings of existing LCCA methods and processes. LCCA research will become more robust if improvements are made, facilitating private industries and government agencies to accomplish their economic aims. Keywords: Life-Cycle Cost Analysis (LCCA, Pavement management, LCCA software, Net Present Value (NPV

A BWR 24-month cycle analysis using multicycle techniques

International Nuclear Information System (INIS)

Hartley, K.D.

1993-01-01

Boiling water reactor (BWR) fuel cycle design analyses have become increasingly challenging in the past several years. As utilities continue to seek improved capacity factors, reduced power generation costs, and reduced outage costs, longer cycle lengths and fuel design optimization become important considerations. Accurate multicycle analysis techniques are necessary to determine the viability of fuel designs and cycle operating strategies to meet reactor operating requirements, e.g., meet thermal and reactivity margin constraints, while minimizing overall fuel cycle costs. Siemens Power Corporation (SPC), Nuclear Division, has successfully employed multi-cycle analysis techniques with realistic rodded cycle depletions to demonstrate equilibrium fuel cycle performance in 24-month cycles. Analyses have been performed by a BWR/5 reactor, at both rated and uprated power conditions

PWR core design, neutronics evaluation and fuel cycle analysis for thorium-uranium breeding recycle

International Nuclear Information System (INIS)

Bi, G.; Liu, C.; Si, S.

2012-01-01

This paper was focused on core design, neutronics evaluation and fuel cycle analysis for Thorium-Uranium Breeding Recycle in current PWRs, without any major change to the fuel lattice and the core internals, but substituting the UOX pellet with Thorium-based pellet. The fuel cycle analysis indicates that Thorium-Uranium Breeding Recycle is technically feasible in current PWRs. A 4-loop, 193-assembly PWR core utilizing 17 x 17 fuel assemblies (FAs) was taken as the model core. Two mixed cores were investigated respectively loaded with mixed reactor grade Plutonium-Thorium (PuThOX) FAs and mixed reactor grade 233 U-Thorium (U 3 ThOX) FAs on the basis of reference full Uranium oxide (UOX) equilibrium-cycle core. The UOX/PuThOX mixed core consists of 121 UOX FAs and 72 PuThOX FAs. The reactor grade 233 U extracted from burnt PuThOX fuel was used to fabrication of U 3 ThOX for starting Thorium-. Uranium breeding recycle. In UOX/U 3 ThOX mixed core, the well designed U 3 ThOX FAs with 1.94 w/o fissile uranium (mainly 233 U) were located on the periphery of core as a blanket region. U 3 ThOX FAs remained in-core for 6 cycles with the discharged burnup achieving 28 GWD/tHM. Compared with initially loading, the fissile material inventory in U 3 ThOX fuel has increased by 7% via 1-year cooling after discharge. 157 UOX fuel assemblies were located in the inner of UOX/U 3 ThOX mixed core refueling with 64 FAs at each cycle. The designed UOX/PuThOX and UOX/U 3 ThOX mixed core satisfied related nuclear design criteria. The full core performance analyses have shown that mixed core with PuThOX loading has similar impacts as MOX on several neutronic characteristic parameters, such as reduced differential boron worth, higher critical boron concentration, more negative moderator temperature coefficient, reduced control rod worth, reduced shutdown margin, etc.; while mixed core with U 3 ThOX loading on the periphery of core has no visible impacts on neutronic characteristics compared

Using Market Forces to Reduce Greenhouse Gas Emissions Through Product-Level Life Cycle Analysis and Eco-Labeling

Science.gov (United States)

Sweeney, J. F.; Davis, S. J.

2007-12-01

Established protocols allow entity-level accounting of greenhouse gas (GHG) emissions. The information contained within GHG inventories is used by entities to manage their carbon footprint and to anticipate future exposure to compulsory GHG markets or taxes. The efficacy of such inventories, as experienced by the consumer, can be improved upon by product-level GHG inventories applying the methods of traditional life cycle analysis (LCA). A voluntary product-level assessment of this type, coupled with an eco-label, would 1) empower consumers with information about the total embodied GHG content of a product, 2) allow companies to understand and manage GHG emissions outside the narrow scope of their entities, and 3) drive reduction of GHG emissions throughout product value chains. The Climate Conservancy (TCC) is a non-profit organization founded to help companies calculate their GHG emissions at the level of individual product units, and to inform consumers about the GHG intensity of the products they choose to purchase. With the assistance of economists, policy experts and scientists, TCC has developed a useful metric for reporting product-level GHG emissions that allows for a normalized comparison of a product's GHG intensity irrespective of industry sector or competitors, where GHG data are often unavailable or incomplete. Using this metric, we envision our Climate Conscious label becoming an important arbiter of choice for consumers seeking ways to mitigate their climate impacts without the need for governmental regulation.

Replenishment policy for an inventory model under inflation

Science.gov (United States)

Singh, Vikramjeet; Saxena, Seema; Singh, Pushpinder; Mishra, Nitin Kumar

2017-07-01

The purpose of replenishment is to keep the flow of inventory in the system. To determine an optimal replenishment policy is a great challenge in developing an inventory model. Inflation is defined as the rate at which the prices of goods and services are rising over a time period. The cost parameters are affected by the rate of inflation. High rate of inflation affects the organizations financial conditions. Based on the above backdrop the present paper proposes the retailers replenishment policy for deteriorating items with different cycle lengths under inflation. The shortages are partially backlogged. At last numerical examples validate the results.

Using Forest Inventory and Analysis data to model plant-climate relationships

Science.gov (United States)

Nicholas L. Crookston; Gerald E. Rehfeldt; Marcus V. Warwell

2007-01-01

Forest Inventory and Analysis (FIA) data from 11 Western conterminous States were used to (1) estimate and map the climatic profiles of tree species and (2) explore how to include climate variables in individual tree growth equations used in the Forest Vegetation Simulator (FVS). On the first front, we found the FIA data to be useful as training data in Breiman's...

ABC Analysis for Inventory Management: Bridging the Gap between Research and Classroom

Science.gov (United States)

Ravinder, Handanhal; Misra, Ram B.

2014-01-01

ABC analysis is a well-established categorization technique based on the Pareto Principle for determining which items should get priority in the management of a company's inventory. In discussing this topic, today's operations management and supply chain textbooks focus on dollar volume as the sole criterion for performing the categorization. The…

Life cycle inventory of biodiesel and petroleum diesel for use in an urban bus. Final report

Energy Technology Data Exchange (ETDEWEB)

Sheehan, J.; Camobreco, V.; Duffield, J.; Graboski, M.; Shapouri, H.

1998-05-01

This report presents the findings from a study of the life cycle inventories for petroleum diesel and biodiesel. It presents information on raw materials extracted from the environment, energy resources consumed, and air, water, and solid waste emissions generated. Biodiesel is a renewable diesel fuel substitute. It can be made from a variety of natural oils and fats. Biodiesel is made by chemically combining any natural oil or fat with an alcohol such as methanol or ethanol. Methanol has been the most commonly used alcohol in the commercial production of biodiesel. In Europe, biodiesel is widely available in both its neat form (100% biodiesel, also known as B1OO) and in blends with petroleum diesel. European biodiesel is made predominantly from rapeseed oil (a cousin of canola oil). In the United States, initial interest in producing and using biodiesel has focused on the use of soybean oil as the primary feedstock mainly because the United States is the largest producer of soybean oil in the world. 170 figs., 148 tabs.

Exploratory Factor Analysis of the Beck Anxiety Inventory and the Beck Depression Inventory-II in a Psychiatric Outpatient Population

Science.gov (United States)

2018-01-01

Background To further understand the relationship between anxiety and depression, this study examined the factor structure of the combined items from two validated measures for anxiety and depression. Methods The participants were 406 patients with mixed psychiatric diagnoses including anxiety and depressive disorders from a psychiatric outpatient unit at a university-affiliated medical center. Responses of the Beck Anxiety Inventory (BAI), Beck Depression Inventory (BDI)-II, and Symptom Checklist-90-Revised (SCL-90-R) were analyzed. We conducted an exploratory factor analysis of 42 items from the BAI and BDI-II. Correlational analyses were performed between subscale scores of the SCL-90-R and factors derived from the factor analysis. Scores of individual items of the BAI and BDI-II were also compared between groups of anxiety disorder (n = 185) and depressive disorder (n = 123). Results Exploratory factor analysis revealed the following five factors explaining 56.2% of the total variance: somatic anxiety (factor 1), cognitive depression (factor 2), somatic depression (factor 3), subjective anxiety (factor 4), and autonomic anxiety (factor 5). The depression group had significantly higher scores for 12 items on the BDI while the anxiety group demonstrated higher scores for six items on the BAI. Conclusion Our results suggest that anxiety and depressive symptoms as measured by the BAI and BDI-II can be empirically differentiated and that particularly items of the cognitive domain in depression and those of physical domain in anxiety are noteworthy. PMID:29651821

Towards Soil and Sediment Inventories of Black Carbon

Science.gov (United States)

Masiello, C. A.

2008-12-01

A body of literature on black carbon (BC) concentrations in soils and sediments is rapidly accumulating, but as of yet, there are no global or regional inventories of BC in either reservoir. Soil and sediment BC inventories are badly needed for a range of fields. For example, in oceanography a global sediment BC inventory is crucial in understanding the role of biomass burning in the development of stable marine carbon reservoirs, including dissolved organic carbon and sedimentary organic carbon. Again in the marine environment, BC likely strongly impacts the fate and transport of anthropogenic pollutants: regional inventories of BC in sediments will help develop better environmental remediation strategies. In terrestrial systems well-constrained natural BC soil inventories would help refine ecological, agricultural, and soil biogeochemical studies. BC is highly sorptive of nutrients including nitrogen and phosphorous. The presence of BC in ecosystems almost certainly alters N and P cycling; however, without soil BC inventories, we cannot know where BC has a significant impact. BC's nutrient sorptivity and water-holding capacity make it an important component of agricultural soils, and some researchers have proposed artificially increasing soil BC inventories to improve soil fertility. Natural soil BC concentrations in some regions are quite high, but without a baseline inventory, it is challenging to predict when agricultural amendment will significantly exceed natural conditions. And finally, because BC is one of the most stable fractions of organic carbon in soils, understanding its concentration and regional distribution will help us track the dynamics of soil organic matter response to changing environmental conditions. Developing effective regional and global BC inventories is challenging both because of data sparsity and methodological intercomparison issues. In this presentation I will describe a roadmap to generating these valuable inventories.

Life cycle inventory of the production of rare earths and the subsequent production of NdFeB rare earth permanent magnets.

Science.gov (United States)

Sprecher, Benjamin; Xiao, Yanping; Walton, Allan; Speight, John; Harris, Rex; Kleijn, Rene; Visser, Geert; Kramer, Gert Jan

2014-04-01

Neodymium is one of the more critical rare earth elements with respect to current availability and is most often used in high performance magnets. In this paper, we compare the virgin production route of these magnets with two hypothetical recycling processes in terms of environmental impact. The first recycling process looks at manual dismantling of computer hard disk drives (HDDs) combined with a novel hydrogen based recycling process. The second process assumes HDDs are shredded. Our life cycle assessment is based both on up to date literature and on our own experimental data. Because the production process of neodymium oxide is generic to all rare earths, we also report the life cycle inventory data for the production of rare earth oxides separately. We conclude that recycling of neodymium, especially via manual dismantling, is preferable to primary production, with some environmental indicators showing an order of magnitude improvement. The choice of recycling technology is also important with respect to resource recovery. While manual disassembly allows in principle for all magnetic material to be recovered, shredding leads to very low recovery rates (<10%).

Modeling and analysis of advanced binary cycles

Energy Technology Data Exchange (ETDEWEB)

Gawlik, K.

1997-12-31

A computer model (Cycle Analysis Simulation Tool, CAST) and a methodology have been developed to perform value analysis for small, low- to moderate-temperature binary geothermal power plants. The value analysis method allows for incremental changes in the levelized electricity cost (LEC) to be determined between a baseline plant and a modified plant. Thermodynamic cycle analyses and component sizing are carried out in the model followed by economic analysis which provides LEC results. The emphasis of the present work is on evaluating the effect of mixed working fluids instead of pure fluids on the LEC of a geothermal binary plant that uses a simple Organic Rankine Cycle. Four resources were studied spanning the range of 265{degrees}F to 375{degrees}F. A variety of isobutane and propane based mixtures, in addition to pure fluids, were used as working fluids. This study shows that the use of propane mixtures at a 265{degrees}F resource can reduce the LEC by 24% when compared to a base case value that utilizes commercial isobutane as its working fluid. The cost savings drop to 6% for a 375{degrees}F resource, where an isobutane mixture is favored. Supercritical cycles were found to have the lowest cost at all resources.

Life cycle environmental performance of renewable building materials in the context of residential construction : phase II research report: an extension to the 2005 phase I research report. Module D, Life cycle inventory of softwood lumber manufacturing in the Northeastern and North Central United States.

Science.gov (United States)

Richard D. Bergman; Scott A. Bowe

2009-01-01

The goal of this study was to gain an understanding of the environmental impact for softwood lumber production through a gate-to-gate life-cycle inventory (LCI) of softwood sawmills in the northeastern and north central United States (NE/NC). Primary mill data were collected per Consortium on Research for Renewable Industrial Material (CORRIM) Research Guidelines (...

Beginning LCA. A guide into environmental life cycle assessment

Energy Technology Data Exchange (ETDEWEB)

Van den Berg, N.W. [ed.; Huppes, G. [Centre of Environmental Science CLM, Leiden University, Leiden (Netherlands); Dutilh, C.E. [Unilever, Van den Bergh Netherlands, Rotterdam (Netherlands)

1995-02-01

The main goal of this document is to provide practical guidance for those who want to start with Life Cycle Assessment (LCA). The document has been set up in the form of modules. Module 1 provides arguments to decide whether or not LCA is the right tool to use in a particular case. In this module other ways to study interactions with the environment will be mentioned as well. Module 2 explains the process of formulating the purpose and scope of the study. The results will give a general picture of the characteristics of the LCA. The next step, which is called the inventory analysis, represents the largest amount of work and is split up into four parts, i.e. Modules 3,4,5, and 6. Module 3 gives guidelines and detailed examples on how to construct a flowchart of the study. Module 5 describes how to collect the required data and Module 4 how to define the system boundaries. Finally, the processing of data is described in Module 6. The result of the inventory is a list of emissions and extractions for all processes involved in manufacturing and required for the functioning of a product, service or activity during the entire life cycle. Sometimes results are so clear that you may decide to stop after the inventory stage. Usually however, it is useful to carry out the impact assessment, which is split up into two parts (Modules 7 and 8). Instructions are given on how to translate the list of environmental interventions of the entire life cycle of the product into a table with scores on environmental themes: the classification/characterization. A basic substance list that might be used is added (Module 7). Also a description showing how to evaluate the results of the classification/characterization is given, so that conclusions may be drawn on the information that has been generated (Module 8). Module 9, the last module, describes how to complete the LCA. It provides suggestions on how to present the results and indications about the improvement analysis.

Analysis of advanced European nuclear fuel cycle scenarios including transmutation and economic estimates

International Nuclear Information System (INIS)

Rodríguez, Iván Merino; Álvarez-Velarde, Francisco; Martín-Fuertes, Francisco

2014-01-01

Highlights: • Four fuel cycle scenarios have been analyzed in resources and economic terms. • Scenarios involve Once-Through, Pu burning, and MA transmutation strategies. • No restrictions were found in terms of uranium and plutonium availability. • The best case cost and the impact of their uncertainties to the LCOE were analyzed. - Abstract: Four European fuel cycle scenarios involving transmutation options (in coherence with PATEROS and CP-ESFR EU projects) have been addressed from a point of view of resources utilization and economic estimates. Scenarios include: (i) the current fleet using Light Water Reactor (LWR) technology and open fuel cycle, (ii) full replacement of the initial fleet with Fast Reactors (FR) burning U–Pu MOX fuel, (iii) closed fuel cycle with Minor Actinide (MA) transmutation in a fraction of the FR fleet, and (iv) closed fuel cycle with MA transmutation in dedicated Accelerator Driven Systems (ADS). All scenarios consider an intermediate period of GEN-III+ LWR deployment and they extend for 200 years, looking for long term equilibrium mass flow achievement. The simulations were made using the TR E VOL code, capable to assess the management of the nuclear mass streams in the scenario as well as economics for the estimation of the levelized cost of electricity (LCOE) and other costs. Results reveal that all scenarios are feasible according to nuclear resources demand (natural and depleted U, and Pu). Additionally, we have found as expected that the FR scenario reduces considerably the Pu inventory in repositories compared to the reference scenario. The elimination of the LWR MA legacy requires a maximum of 55% fraction (i.e., a peak value of 44 FR units) of the FR fleet dedicated to transmutation (MA in MOX fuel, homogeneous transmutation) or an average of 28 units of ADS plants (i.e., a peak value of 51 ADS units). Regarding the economic analysis, the main usefulness of the provided economic results is for relative comparison of

Double shell tanks plutonium inventory assessment

International Nuclear Information System (INIS)

Tusler, L.A.

1995-01-01

This report provides an evaluation that establishes plutonium inventory estimates for all DSTs based on known tank history information, the DST plutonium inventory tracking system, tank characterization measurements, tank transfer records, and estimated average concentration values for the various types of waste. These estimates use data through December 31, 1994, and give plutonium estimates as of January 1, 1995. The plutonium inventory values for the DSTs are given in Section 31. The plutonium inventory estimate is 224 kg for the DSTs and 854 kg for the SSTs for a total of 1078 kg. This value compares favorably with the total plutonium inventory value of 981 kg obtained from the total plutonium production minus plutonium recovery analysis estimates

INVENTORY ABSTRACTION

International Nuclear Information System (INIS)

Ragan, G.

2001-01-01

The purpose of the inventory abstraction, which has been prepared in accordance with a technical work plan (CRWMS M andO 2000e for/ICN--02 of the present analysis, and BSC 2001e for ICN 03 of the present analysis), is to: (1) Interpret the results of a series of relative dose calculations (CRWMS M andO 2000c, 2000f). (2) Recommend, including a basis thereof, a set of radionuclides that should be modeled in the Total System Performance Assessment in Support of the Site Recommendation (TSPA-SR) and the Total System Performance Assessment in Support of the Final Environmental Impact Statement (TSPA-FEIS). (3) Provide initial radionuclide inventories for the TSPA-SR and TSPA-FEIS models. (4) Answer the U.S. Nuclear Regulatory Commission (NRC)'s Issue Resolution Status Report ''Key Technical Issue: Container Life and Source Term'' (CLST IRSR) key technical issue (KTI): ''The rate at which radionuclides in SNF [spent nuclear fuel] are released from the EBS [engineered barrier system] through the oxidation and dissolution of spent fuel'' (NRC 1999, Subissue 3). The scope of the radionuclide screening analysis encompasses the period from 100 years to 10,000 years after the potential repository at Yucca Mountain is sealed for scenarios involving the breach of a waste package and subsequent degradation of the waste form as required for the TSPA-SR calculations. By extending the time period considered to one million years after repository closure, recommendations are made for the TSPA-FEIS. The waste forms included in the inventory abstraction are Commercial Spent Nuclear Fuel (CSNF), DOE Spent Nuclear Fuel (DSNF), High-Level Waste (HLW), naval Spent Nuclear Fuel (SNF), and U.S. Department of Energy (DOE) plutonium waste. The intended use of this analysis is in TSPA-SR and TSPA-FEIS. Based on the recommendations made here, models for release, transport, and possibly exposure will be developed for the isotopes that would be the highest contributors to the dose given a release

Parametric-based thermodynamic analysis of organic Rankine cycle as bottoming cycle for combined-cycle power plant

International Nuclear Information System (INIS)

Qureshi, S.; Memon, A.G.; Abbasi, A.F.

2017-01-01

In Pakistan, the thermal efficiency of the power plants is low because of a huge share of fuel energy is dumped into the atmosphere as waste heat. The ORC (Organic Rankine Cycle) has been revealed as one of the promising technologies to recover waste heat to enhance the thermal efficiency of the power plant. In current work, ORC is proposed as a second bottoming cycle for existing CCPP (Combined Cycle Power Plant). In order to assess the efficiency of the plant, a thermodynamic model is developed in the ESS (Engineering Equation Solver) software. The developed model is used for parametric analysis to assess the effects of various operating parameters on the system performance. The analysis of results shows that the integration of ORC system with existing CCPP system enhances the overall power output in the range of 150.5-154.58 MW with 0.24-5% enhancement in the efficiency depending on the operating conditions. During the parametric analysis of ORC, it is observed that inlet pressure of the turbine shows a significant effect on the performance of the system as compared to other operating parameters. (author)

Inventory model with cash flow oriented and time-dependent holding cost under permissible delay in payments

Directory of Open Access Journals (Sweden)

Tripathi R.P.

2013-01-01

Full Text Available This study develops an inventory model for determining an optimal ordering policy for non-deteriorating items and time-dependent holding cost with delayed payments permitted by the supplier under inflation and time-discounting. The discounted cash flows approach is applied to study the problem analysis. Mathematical models have been derived under two different situations i.e. case I: The permissible delay period is less than cycle time for settling the account and case II: The permissible delay period is greater than or equal to cycle time for settling the account. An algorithm is used to obtain minimum total present value of the costs over the time horizon H. Finally, numerical example and sensitivity analysis demonstrate the applicability of the proposed model. The main purpose of this paper is to investigate the optimal cycle time and optimal payment time for an item so that annual total relevant cost is minimized.

The Coopersmith Self-Esteem Inventory: analysis and partial validation of a modified adult form.

Science.gov (United States)

Myhill, J; Lorr, M

1978-01-01

Determined the factor structure of an adult form of the Coopersmith Self-Esteem Inventory (SEI), tested several hypotheses related to its content, and assessed the utility of the five derived scores for differentiating psychiatric outpatients from normals. The modified Self-Esteem Inventory and six other scales were completed by 200 local-government employees. A principal components analysis of correlations among 58 SEI items and two marker variables revealed five factors. The rotated dimensions were labelled (1) anxiety; (2) defensiveness; (3) negative social attitude; (4) rejection of self; and (5) inadequacy of self. Fifty psychiatric outpatients were compared with 100 normals with respect to the five derived factor scores. Tests of significance indicated that the two groups differed significantly on all measures except the defensiveness or lie scale factor. It is concluded that the Coopersmith Inventory is complex and measures several characteristics in addition to self-esteem.

Analysis of uncertainty propagation in nuclear fuel cycle scenarios

International Nuclear Information System (INIS)

Krivtchik, Guillaume

2014-01-01

Nuclear scenario studies model nuclear fleet over a given period. They enable the comparison of different options for the reactor fleet evolution, and the management of the future fuel cycle materials, from mining to disposal, based on criteria such as installed capacity per reactor technology, mass inventories and flows, in the fuel cycle and in the waste. Uncertainties associated with nuclear data and scenario parameters (fuel, reactors and facilities characteristics) propagate along the isotopic chains in depletion calculations, and through out the scenario history, which reduces the precision of the results. The aim of this work is to develop, implement and use a stochastic uncertainty propagation methodology adapted to scenario studies. The method chosen is based on development of depletion computation surrogate models, which reduce the scenario studies computation time, and whose parameters include perturbations of the depletion model; and fabrication of equivalence model which take into account cross-sections perturbations for computation of fresh fuel enrichment. Then the uncertainty propagation methodology is applied to different scenarios of interest, considering different options of evolution for the French PWR fleet with SFR deployment. (author) [fr

Thermodynamic Analysis of Supplementary-Fired Gas Turbine Cycles

DEFF Research Database (Denmark)

Elmegaard, Brian; Henriksen, Ulrik Birk; Qvale, Einar Bjørn

2002-01-01

This paper presents an analysis of the possibilities for improving the efficiency of an indirectly biomass-fired gas turbine (IBFGT) by supplementary direct gas-firing. The supplementary firing may be based on natural gas, biogas, or pyrolysis gas. {The interest in this cycle arise from a recent...... demonstration of a two-stage gasification process through construction of several plants.} A preliminary analysis of the ideal recuperated Brayton cycle shows that for this cycle any supplementary firing will have a marginal efficiency of unity per extra unit of fuel. The same result is obtained...

Licensed fuel facility status report. Inventory difference data, July 1, 1995--June 30, 1996

International Nuclear Information System (INIS)

Pham, T.N.

1998-02-01

The U.S. Nuclear Regulatory Commission is committed to an annual publication of licensed fuel cycle facility inventory difference data, following Agency review of the information and completion of any related investigations. Information in this report includes inventory difference results for active fuel fabrication facilities possessing more than one effective kilogram of special nuclear material. 1 tab

Differential Item Functioning Analysis of the Mental, Emotional, and Bodily Toughness Inventory

Science.gov (United States)

Gao, Yong; Mack, Mick G.; Ragan, Moira A.; Ragan, Brian

2012-01-01

In this study the authors used differential item functioning analysis to examine if there were items in the Mental, Emotional, and Bodily Toughness Inventory functioning differently across gender and athletic membership. A total of 444 male (56.3%) and female (43.7%) participants (30.9% athletes and 69.1% non-athletes) responded to the Mental,…

Design and psychometric analysis of the Hopelessness and Suicide Ideation Inventory “IDIS”

Directory of Open Access Journals (Sweden)

Bertha Lucía Avendaño Prieto

2016-01-01

Full Text Available The objective was to design the Hopeless and Suicide Ideation Inventory, also know as IDIS - Spanish acronym for Inventario de Desesperanza e Ideación Suicida - and to analyze its psychometric properties. A quantitative empirical research was conducted employing a non-experimental design, an instrumental variable and cross-sectional analysis. Three hundred and thirty-nine people participated in the study (67.6% females, 31.6% males, in which 54.6% were students and 34.8% were employees. Participants completed the IDIS, the Beck Depression Inventory (BDI-II, the Positive and Negative Suicide Ideation Inventory, and the Beck Hopelessness Scale. The results indicated an inter-rater reliability and a positive convergent validity in both scales. Suicidal ideation revealed an internal consistency of α = .76, and α = .81 for hopelessness; a total variance of 41.77% and 47.52% was obtained correspondingly. Based on the Item Response Theory (IRT, the adjustments for INFIT and OUTFIT fell under the expected range. It was concluded that the IDIS is a reliable and valid measure, however, further evaluations on sensitivity and specificity are encouraged.

Assessing environmental impacts in a life cycle perspective

DEFF Research Database (Denmark)

Hauschild, Michael Zwicky

2005-01-01

is focused on the product system which comprises all the processes which the product and its components meet throughout their lives- from the extraction of raw materials via manufacture, use and waste management to final disposal, or in short from the cradle to the grave (see Figure 1). The focus......What are the environmental impacts from an armchairor a cellular phone or a steak, if you take into account all the activities needed to produce, maintain, use or consume and eventually dispose of it? Life cycle impact assessment is the part of life cycle assessment (LCA) where the inventory...... of material flows in the life cycle of a product are translated into environmental impacts and consumption of resources, and questions like these are given an answer. The environmental impacts may range from very local (e.g. land use) to global (like climate change). As an environmental analysis tool, LCA...

A single product perishing inventory model with demand interaction

African Journals Online (AJOL)

The paper describes a single perishing product inventory model in which ... continuous review inventory models have been studied recently by Yadavalli et al ...... stochastic inventory system with lost sales, Stochastic Analysis and Applications ...

Concept for fuel-cycle based safeguards

International Nuclear Information System (INIS)

deMontmollin, J.M.; Higinbotham, W.A.; Gupta, D.

1985-01-01

Although the guidelines for NPT safeguards specify that the State's fuel cycle and degree of international independence are to be taken into account, the same model approach and absolute-quantity inspection goals are applied to all similar facilities, irrespective of the State's fuel cycle, and the findings are reported in those terms. A concept whereby safeguards might more effectively and efficiently accomplish the purposes of NPT safeguards is explored. The principal features are: (1) division of the fuel cycle into three zones, each containing material having a different degree of significance for safeguards; (2) closing a verified material balance around each zone, supplementing the present MBA balances for more sensitive facilities and replacing them for others; (3) maintenance by the IAEA of a current book inventory for each facility by means of immediate, abbreviated reporting of interfacility transfers; (4) near real-time analysis of material flow patterns through the fuel cycle; and (5) a periodic statement of the findings for the entire State that takes the form that there is assurance that all nuclear materials under safeguards are accounted for to some stated degree of uncertainty

The annual cycle of plutonium in the water column of a warm, monomictic reservoir

International Nuclear Information System (INIS)

Pinder, J.E. III; Alberts, J.J.; Bowling, J.W.; Nelson, D.M.; Orlandini, K.A.

1992-01-01

An annual cycle occurs in the 239,240 Pu inventories of the water column of Pond B, an 87-ha warm monomictic reservoir on the US Department of Energy's Savannah River Site in Barnwell Co., South Carolina. The pond has elevated concentrations of 238 Pu and 239,240 Pu in sediments due to releases from former reactor operations and continues to receive additional Pu input from atmospheric deposition. For surface waters, the 239,240 Pu inventory increases following turnover in November to a maximum in March followed by a decline until later summer when minimum inventories occur. For deeper waters, the 239,240 Pu inventories increase rapidly following turnover and reach maximum values in March. The inventories in deeper waters remain large from March until turnover. Maximum inventories for the entire water column occur in March with minimum inventories at turnover in October and November. Turnover results in a redistribution of Pu across water depth but no measurable Pu loss from the water column. Ratios of 238 Pu: 239,240 Pu indicate that the cycle involves primarily Pu from sediment sources with little influence from atmospheric sources. Thus, the cycle represents net remobilization of 239,240 Pu from the sediments to the water column during the oxic, holomictic portion of the year followed by a net loss of Pu from the water column once stratification occurs. (author)

Cartographic standards to improve maps produced by the Forest Inventory and Analysis program

Science.gov (United States)

Charles H. (Hobie) Perry; Mark D. Nelson

2009-01-01

The Forest Service, U.S. Department of Agriculture's Forest Inventory and Analysis (FIA) program is incorporating an increasing number of cartographic products in reports, publications, and presentations. To create greater quality and consistency within the national FIA program, a Geospatial Standards team developed cartographic design standards for FIA map...

78 FR 17205 - Notice of Availability of Service Contract Inventories

Science.gov (United States)

2013-03-20

... FEDERAL MARITIME COMMISSION Notice of Availability of Service Contract Inventories AGENCY: Federal Maritime Commission. ACTION: Notice of availability of service contract inventories. FOR FURTHER... Service Contract Inventory Analysis, the FY 2012 Service Contract Inventory, and the FY 2012 Service...

Optimal Inventory Policy under Permissible Payment Delay in Fashion Supply Chains

OpenAIRE

Guo Li; Yuchen Kang; Mengqi Liu; Zhaohua Wang

2014-01-01

This paper investigates a retailer’s optimal inventory cycle and the corresponding time of payment in fashion supply chains where a supplier allows the payment delay. Here according to the established model we first analyze the retailer's reaction, and then find out the retailer’s optimal inventory policy and time of payment to maximize its total profit. Our result shows that it is not always the best choice for retailers of fashion supply chains to choose the discount way to replenish stocks...

Inventory Control System by Using Vendor Managed Inventory (VMI)

Science.gov (United States)

Sabila, Alzena Dona; Mustafid; Suryono

2018-02-01

The inventory control system has a strategic role for the business in managing inventory operations. Management of conventional inventory creates problems in the stock of goods that often runs into vacancies and excess goods at the retail level. This study aims to build inventory control system that can maintain the stability of goods availability at the retail level. The implementation of Vendor Managed Inventory (VMI) method on inventory control system provides transparency of sales data and inventory of goods at retailer level to supplier. Inventory control is performed by calculating safety stock and reorder point of goods based on sales data received by the system. Rule-based reasoning is provided on the system to facilitate the monitoring of inventory status information, thereby helping the process of inventory updates appropriately. Utilization of SMS technology is also considered as a medium of collecting sales data in real-time due to the ease of use. The results of this study indicate that inventory control using VMI ensures the availability of goods ± 70% and can reduce the accumulation of goods ± 30% at the retail level.

Life cycle and nano-products: end-of-life assessment

International Nuclear Information System (INIS)

Asmatulu, Eylem; Twomey, Janet; Overcash, Michael

2012-01-01

Understanding environmental impacts of nanomaterials necessitates analyzing the life cycle profile. The initial emphasis of nanomaterial life cycle studies has been on the environmental and health effects of nanoproducts during the production and usage stages. Analyzing the end-of-life (eol) stage of nanomaterials is also critical because significant impacts or benefits for the environment may arise at that particular stage. In this article, the Woodrow Wilson Center’s Project on Emerging Nanotechnologies (PEN) Consumer Products Inventory (CPI) model was used, which contains a relatively large and complete nanoproduct list (1,014) as of 2010. The consumer products have wide range of applications, such as clothing, sports goods, personal care products, medicine, as well as contributing to faster cars and planes, more powerful computers and satellites, better micro and nanochips, and long-lasting batteries. In order to understand the eol cycle concept, we allocated 1,014 nanoproducts into the nine end-of-life categories (e.g., recyclability, ingestion, absorption by skin/public sewer, public sewer, burning/landfill, landfill, air release, air release/public sewer, and other) based on probable final destinations of the nanoproducts. This article highlights the results of this preliminary assessment of end-of-life stage of nanoproducts. The largest potential eol fate was found to be recyclability, however little literature appears to have evolved around nanoproduct recycling. At lower frequency is dermal and ingestion human uptake and then landfill. Release to water and air are much lower potential eol fates for current nanoproducts. In addition, an analysis of nano-product categories with the largest number of products listed indicated that clothes, followed by dermal-related products and then sports equipment were the most represented in the PEN CPI (http://www.nanotechproject.org/inventories/consumer/browse/categories/http://www.nanotechproject.org/inventories

Life cycle and nano-products: end-of-life assessment

Energy Technology Data Exchange (ETDEWEB)

Asmatulu, Eylem; Twomey, Janet; Overcash, Michael, E-mail: mrovercash@earthlink.net [Wichita State University, Department of Industrial and Manufacturing Engineering (United States)

2012-03-15

Understanding environmental impacts of nanomaterials necessitates analyzing the life cycle profile. The initial emphasis of nanomaterial life cycle studies has been on the environmental and health effects of nanoproducts during the production and usage stages. Analyzing the end-of-life (eol) stage of nanomaterials is also critical because significant impacts or benefits for the environment may arise at that particular stage. In this article, the Woodrow Wilson Center's Project on Emerging Nanotechnologies (PEN) Consumer Products Inventory (CPI) model was used, which contains a relatively large and complete nanoproduct list (1,014) as of 2010. The consumer products have wide range of applications, such as clothing, sports goods, personal care products, medicine, as well as contributing to faster cars and planes, more powerful computers and satellites, better micro and nanochips, and long-lasting batteries. In order to understand the eol cycle concept, we allocated 1,014 nanoproducts into the nine end-of-life categories (e.g., recyclability, ingestion, absorption by skin/public sewer, public sewer, burning/landfill, landfill, air release, air release/public sewer, and other) based on probable final destinations of the nanoproducts. This article highlights the results of this preliminary assessment of end-of-life stage of nanoproducts. The largest potential eol fate was found to be recyclability, however little literature appears to have evolved around nanoproduct recycling. At lower frequency is dermal and ingestion human uptake and then landfill. Release to water and air are much lower potential eol fates for current nanoproducts. In addition, an analysis of nano-product categories with the largest number of products listed indicated that clothes, followed by dermal-related products and then sports equipment were the most represented in the PEN CPI (http://www.nanotechproject.org/inventories/consumer/browse/categories/http://www.nanotechproject.org/inventories

Spectral Analysis Of Business Cycles In The Visegrad Group Countries

Directory of Open Access Journals (Sweden)

Kijek Arkadiusz

2017-06-01

Full Text Available This paper examines the business cycle properties of Visegrad group countries. The main objective is to identify business cycles in these countries and to study the relationships between them. The author applies a modification of the Fourier analysis to estimate cycle amplitudes and frequencies. This allows for a more precise estimation of cycle characteristics than the traditional approach. The cross-spectral analysis of GDP cyclical components for the Czech Republic, Hungary, Poland and Slovakia makes it possible to assess the degree of business cycle synchronization between the countries.

Meta-Analysis of the English Version of the Beck Depression Inventory-Second Edition

Science.gov (United States)

Erford, Bradley T.; Johnson, Erin; Bardoshi, Gerta

2016-01-01

This meta-analysis reviewed 144 studies from 1996 to 2013 using the Beck Depression Inventory-Second Edition. Internal consistency was 0.89 and test-retest reliability 0.75. Convergent comparisons were robust across 43 depression instruments. Structural validity supported both one- and two-factor solutions and diagnostic accuracy varied according…

Innovation of the Process of Inventorying of the Selected Transport Units: Case Study in the Automotive Industry

Directory of Open Access Journals (Sweden)

Chocholáč Jan

2017-05-01

Full Text Available In the current situation, highly competitive time when the emphasis is on shortening delivery schedules, streamlining the production cycle and, ultimately, reducing the total cost businesses are forced to optimizations and innovations. The article deals with the inventory of the selected transport units in warehouses. The inventory is currently being carried out through manual labor of employees. This paper proposes a possible implementation of new and innovative approach to inventory control, with the help of an automated inventory realized by the drones.

The construct validity of the Major Depression Inventory

DEFF Research Database (Denmark)

Nielsen, Marie Germund; Ørnbøl, Eva; Vestergaard, Mogens

2017-01-01

Objective We aimed to assess the measurement properties of the ten-item Major Depression Inventory when used on clinical suspicion in general practice by performing a Rasch analysis. Methods General practitioners asked consecutive persons to respond to the web-based Major Depression Inventory...... on clinical suspicion of depression. We included 22 practices and 245 persons. Rasch analysis was performed using RUMM2030 software. The Rasch model fit suggests that all items contribute to a single underlying trait (defined as internal construct validity). Mokken analysis was used to test dimensionality...... for gender, age, work status and education. The Rasch and Mokken analyses revealed two dimensions, but the Major Depression Inventory showed fit to one scale if items 9 and 10 were excluded. Conclusion Our study indicated scalability problems in the current version of the Major Depression Inventory...

Development of dynamic simulation code for fuel cycle of fusion reactor. 1. Single pulse operation simulation

Energy Technology Data Exchange (ETDEWEB)

Aoki, Isao; Seki, Yasushi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment; Sasaki, Makoto; Shintani, Kiyonori; Kim, Yeong-Chan

1997-11-01

A dynamic simulation code for the fuel cycle of a fusion experimental reactor has been developed. The code follows the fuel inventory change with time in the plasma chamber and the fuel cycle system during a single pulse operation. The time dependence of the fuel inventory distribution is evaluated considering the fuel burn and exhaust in the plasma chamber, purification and supply functions. For each subsystem of the plasma chamber and the fuel cycle system, the fuel inventory equation is written based on the equation of state considering the function of fuel burn, exhaust, purification, and supply. The processing constants of subsystem for the steady states were taken from the values in the ITER Conceptual Design Activity (CDA) report. Using the code, the time dependence of the fuel supply and inventory depending on the burn state and subsystem processing functions are shown. (author)

Inventory Control System by Using Vendor Managed Inventory (VMI

Directory of Open Access Journals (Sweden)

Dona Sabila Alzena

2018-01-01

Full Text Available The inventory control system has a strategic role for the business in managing inventory operations. Management of conventional inventory creates problems in the stock of goods that often runs into vacancies and excess goods at the retail level. This study aims to build inventory control system that can maintain the stability of goods availability at the retail level. The implementation of Vendor Managed Inventory (VMI method on inventory control system provides transparency of sales data and inventory of goods at retailer level to supplier. Inventory control is performed by calculating safety stock and reorder point of goods based on sales data received by the system. Rule-based reasoning is provided on the system to facilitate the monitoring of inventory status information, thereby helping the process of inventory updates appropriately. Utilization of SMS technology is also considered as a medium of collecting sales data in real-time due to the ease of use. The results of this study indicate that inventory control using VMI ensures the availability of goods ± 70% and can reduce the accumulation of goods ± 30% at the retail level.

Analysis of environmental friendliness of DUPIC fuel cycle

International Nuclear Information System (INIS)

Ko, Won Il; Kim, Ho Dong

2001-07-01

Some properties of irradiated DUPIC fuels are compared with those of other fuel cycles. It was indicated that the toxicity of the DUPIC option based on 1 GWe-yr is much smaller than those of other fuel cycle options, and is just about half the order of magnitude of other fuel cycles. From the activity analysis of 99 Tc and 237 Np, which are important to the long-term transport of fission products stored in geologic media, the DUPIC option, was being contained only about half of those other options. It was found from the actinide content estimation that the MOX option has the lowest plutonium arising based on 1 GWe-year and followed by the DUPIC option. However, fissile Pu content generated in the DUPIC fuel was the lowest among the fuel cycle options. From the analysis of radiation barrier in proliferation resistance aspect, the fresh DUPIC fuel can play a radiation barrier part, better than CANDU spent fuels as well as fresh MOX fuel. It is indicated that the DUPIC fuel cycle has the excellent resistance to proliferation, compared with an existing reprocessing option and CANDU once-through option. In conclusions, DUPIC fuel cycle would have good properties on environmental effect and proliferation resistance, compared to other fuel cycle cases

Parking infrastructure: energy, emissions, and automobile life-cycle environmental accounting

Energy Technology Data Exchange (ETDEWEB)

Chester, Mikhail; Horvath, Arpad; Madanat, Samer, E-mail: mchester@cal.berkeley.edu, E-mail: horvath@ce.berkeley.edu, E-mail: madanat@ce.berkeley.edu [Department of Civil and Environmental Engineering, University of California, Berkeley, Berkeley CA 94720 (United States)

2010-07-15

The US parking infrastructure is vast and little is known about its scale and environmental impacts. The few parking space inventories that exist are typically regionalized and no known environmental assessment has been performed to determine the energy and emissions from providing this infrastructure. A better understanding of the scale of US parking is necessary to properly value the total costs of automobile travel. Energy and emissions from constructing and maintaining the parking infrastructure should be considered when assessing the total human health and environmental impacts of vehicle travel. We develop five parking space inventory scenarios and from these estimate the range of infrastructure provided in the US to be between 105 million and 2 billion spaces. Using these estimates, a life-cycle environmental inventory is performed to capture the energy consumption and emissions of greenhouse gases, CO, SO{sub 2}, NO{sub X}, VOC (volatile organic compounds), and PM{sub 10} (PM: particulate matter) from raw material extraction, transport, asphalt and concrete production, and placement (including direct, indirect, and supply chain processes) of space construction and maintenance. The environmental assessment is then evaluated within the life-cycle performance of sedans, SUVs (sports utility vehicles), and pickups. Depending on the scenario and vehicle type, the inclusion of parking within the overall life-cycle inventory increases energy consumption from 3.1 to 4.8 MJ by 0.1-0.3 MJ and greenhouse gas emissions from 230 to 380 g CO{sub 2}e by 6-23 g CO{sub 2}e per passenger kilometer traveled. Life-cycle automobile SO{sub 2} and PM{sub 10} emissions show some of the largest increases, by as much as 24% and 89% from the baseline inventory. The environmental consequences of providing the parking spaces are discussed as well as the uncertainty in allocating paved area between parking and roadways.

Nuclear Fuel Cycle System Analysis (I)

Energy Technology Data Exchange (ETDEWEB)

Ko, Won Il; Kwon, Eun Ha; Kim, Ho Dong; Yoon, Ji Sup; Park, Seong Won

2006-12-15

As a nation develops strategies that provide nuclear energy while meeting its various objectives, it must begin with identification of a fuel cycle option that can be best suitable for the country. For such a purpose, this paper takes four different fuel cycle options - Once-through Cycle, DUPIC Recycle, Thermal Reactor Recycle and GEN-IV Recycle, and evaluates each option in terms of sustainability, environment-friendliness, proliferation-resistance and economics. The analysis shows that the GEN-IV Recycle appears to have an advantage in terms of sustainability, environment-friendliness and long-term proliferation-resistance, while it is expected to be more economically competitive, if uranium ore prices increase or costs of pyroprocessing and fuel fabrication decrease.

Economics analysis of fuel cycle cost of fusion–fission hybrid reactors based on different fuel cycle strategies

Energy Technology Data Exchange (ETDEWEB)

Zu, Tiejun, E-mail: tiejun@mail.xjtu.edu.cn; Wu, Hongchun; Zheng, Youqi; Cao, Liangzhi

2015-01-15

Highlights: • Economics analysis of fuel cycle cost of FFHRs is carried out. • The mass flows of different fuel cycle strategies are established based on the equilibrium fuel cycle model. • The levelized fuel cycle costs of different fuel cycle strategies are calculated, and compared with current once-through fuel cycle. - Abstract: The economics analysis of fuel cycle cost of fusion–fission hybrid reactors has been performed to compare four fuel cycle strategies: light water cooled blanket burning natural uranium (Strategy A) or spent nuclear fuel (Strategy B), sodium cooled blanket burning transuranics (Strategy C) or minor actinides (Strategy D). The levelized fuel cycle costs (LFCC) which does not include the capital cost, operation and maintenance cost have been calculated based on the equilibrium mass flows. The current once-through (OT) cycle strategy has also been analyzed to serve as the reference fuel cycle for comparisons. It is found that Strategy A and Strategy B have lower LFCCs than OT cycle; although the LFCC of Strategy C is higher than that of OT cycle when the uranium price is at its nominal value, it would become comparable to that of OT cycle when the uranium price reaches its historical peak value level; Strategy D shows the highest LFCC, because it needs to reprocess huge mass of spent nuclear fuel; LFCC is sensitive to the discharge burnup of the nuclear fuel.

Inventory Control System by Using Vendor Managed Inventory (VMI)

OpenAIRE

Dona Sabila Alzena; Mustafid Mustafid; Suryono Suryono

2018-01-01

The inventory control system has a strategic role for the business in managing inventory operations. Management of conventional inventory creates problems in the stock of goods that often runs into vacancies and excess goods at the retail level. This study aims to build inventory control system that can maintain the stability of goods availability at the retail level. The implementation of Vendor Managed Inventory (VMI) method on inventory control system provides transparency of sales data an...

Web-based turbine cycle performance analysis for nuclear power plants

International Nuclear Information System (INIS)

Heo, Gyun Young; Lee, Sung Jin; Chang, Soon Heung; Choi, Seong Soo

2000-01-01

As an approach to improve the economical efficiency of operating nuclear power plants, a thermal performance analysis tool for steam turbine cycle has been developed. For the validation and the prediction of the signals used in thermal performance analysis, a few statistical signal processing techniques are integrated. The developed tool provides predicted performance calculation capability that is steady-state wet steam turbine cycle simulation, and measurement performance calculation capability which determines component- and cycle-level performance indexes. Web-based interface with all performance analysis is implemented, so even remote users can achieve performance analysis. Comparing to ASME PTC6 (Performance Test Code 6), the focusing point of the developed tool is historical performance analysis rather than single accurate performance test. The proposed signal processing techniques are validated using actual plant signals, and turbine cycle models are tested by benchmarking with a commercial thermal analysis tool

A New Dynamic Model for Nuclear Fuel Cycle System Analysis

International Nuclear Information System (INIS)

Choi, Sungyeol; Ko, Won Il

2014-01-01

The evaluation of mass flow is a complex process where numerous parameters and their complex interaction are involved. Given that many nuclear power countries have light and heavy water reactors and associated fuel cycle technologies, the mass flow analysis has to consider a dynamic transition from the open fuel cycle to other cycles over decades or a century. Although an equilibrium analysis provides insight concerning the end-states of fuel cycle transitions, it cannot answer when we need specific management options, whether the current plan can deliver these options when needed, and how fast the equilibrium can be achieved. As a pilot application, the government brought several experts together to conduct preliminary evaluations for nuclear fuel cycle options in 2010. According to Table 1, they concluded that the closed nuclear fuel cycle has long-term advantages over the open fuel cycle. However, it is still necessary to assess these options in depth and to optimize transition paths of these long-term options with advanced dynamic fuel cycle models. A dynamic simulation model for nuclear fuel cycle systems was developed and its dynamic mass flow analysis capability was validated against the results of existing models. This model can reflects a complex combination of various fuel cycle processes and reactor types, from once-through to multiple recycling, within a single nuclear fuel cycle system. For the open fuel cycle, the results of the developed model are well matched with the results of other models

Nuclear Fuel Cycle Analysis Technology to Develop Advanced Nuclear Fuel Cycle

Energy Technology Data Exchange (ETDEWEB)

Park, Byung Heung [Chungju National University, Chungju (Korea, Republic of); Ko, Won IL [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2011-12-15

The nuclear fuel cycle (NFC) analysis is a study to set a NFC policy and to promote systematic researches by analyzing technologies and deriving requirements at each stage of a fuel cycle. System analysis techniques are utilized for comparative analysis and assessment of options on a considered system. In case that NFC is taken into consideration various methods of the system analysis techniques could be applied depending on the range of an interest. This study presented NFC analysis strategies for the development of a domestic advanced NFC and analysis techniques applicable to different phases of the analysis. Strategically, NFC analysis necessitates the linkage with technology analyses, domestic and international interests, and a national energy program. In this respect, a trade-off study is readily applicable since it includes various aspects on NFC as metrics and then analyzes the considered NFC options according to the derived metrics. In this study, the trade-off study was identified as a method for NFC analysis with the derived strategies and it was expected to be used for development of an advanced NFC. A technology readiness level (TRL) method and NFC simulation codes could be utilized to obtain the required metrics and data for assessment in the trade-off study. The methodologies would guide a direction of technology development by comparing and assessing technological, economical, environmental, and other aspects on the alternatives. Consequently, they would contribute for systematic development and deployment of an appropriate advanced NFC.

Nuclear Fuel Cycle Analysis Technology to Develop Advanced Nuclear Fuel Cycle

International Nuclear Information System (INIS)

Park, Byung Heung; Ko, Won IL

2011-01-01

The nuclear fuel cycle (NFC) analysis is a study to set a NFC policy and to promote systematic researches by analyzing technologies and deriving requirements at each stage of a fuel cycle. System analysis techniques are utilized for comparative analysis and assessment of options on a considered system. In case that NFC is taken into consideration various methods of the system analysis techniques could be applied depending on the range of an interest. This study presented NFC analysis strategies for the development of a domestic advanced NFC and analysis techniques applicable to different phases of the analysis. Strategically, NFC analysis necessitates the linkage with technology analyses, domestic and international interests, and a national energy program. In this respect, a trade-off study is readily applicable since it includes various aspects on NFC as metrics and then analyzes the considered NFC options according to the derived metrics. In this study, the trade-off study was identified as a method for NFC analysis with the derived strategies and it was expected to be used for development of an advanced NFC. A technology readiness level (TRL) method and NFC simulation codes could be utilized to obtain the required metrics and data for assessment in the trade-off study. The methodologies would guide a direction of technology development by comparing and assessing technological, economical, environmental, and other aspects on the alternatives. Consequently, they would contribute for systematic development and deployment of an appropriate advanced NFC.

Purchasing and inventory management techniques for optimizing inventory investment

International Nuclear Information System (INIS)

McFarlane, I.; Gehshan, T.

1993-01-01

In an effort to reduce operations and maintenance costs among nuclear plants, many utilities are taking a closer look at their inventory investment. Various approaches for inventory reduction have been used and discussed, but these approaches are often limited to an inventory management perspective. Interaction with purchasing and planning personnel to reduce inventory investment is a necessity in utility efforts to become more cost competitive. This paper addresses the activities that purchasing and inventory management personnel should conduct in an effort to optimize inventory investment while maintaining service-level goals. Other functions within a materials management organization, such as the warehousing and investment recovery functions, can contribute to optimizing inventory investment. However, these are not addressed in this paper because their contributions often come after inventory management and purchasing decisions have been made

Presentation and analysis of a worldwide database of earthquake-induced landslide inventories

Science.gov (United States)

Tanyas, Hakan; van Westen, Cees J.; Allstadt, Kate E.; Nowicki Jessee, M. Anna; Gorum, Tolga; Jibson, Randall W.; Godt, Jonathan W.; Sato, Hiroshi P.; Schmitt, Robert G.; Marc, Odin; Hovius, Niels

2017-01-01

Earthquake-induced landslide (EQIL) inventories are essential tools to extend our knowledge of the relationship between earthquakes and the landslides they can trigger. Regrettably, such inventories are difficult to generate and therefore scarce, and the available ones differ in terms of their quality and level of completeness. Moreover, access to existing EQIL inventories is currently difficult because there is no centralized database. To address these issues, we compiled EQIL inventories from around the globe based on an extensive literature study. The database contains information on 363 landslide-triggering earthquakes and includes 66 digital landslide inventories. To make these data openly available, we created a repository to host the digital inventories that we have permission to redistribute through the U.S. Geological Survey ScienceBase platform. It can grow over time as more authors contribute their inventories. We analyze the distribution of EQIL events by time period and location, more specifically breaking down the distribution by continent, country, and mountain region. Additionally, we analyze frequency distributions of EQIL characteristics, such as the approximate area affected by landslides, total number of landslides, maximum distance from fault rupture zone, and distance from epicenter when the fault plane location is unknown. For the available digital EQIL inventories, we examine the underlying characteristics of landslide size, topographic slope, roughness, local relief, distance to streams, peak ground acceleration, peak ground velocity, and Modified Mercalli Intensity. Also, we present an evaluation system to help users assess the suitability of the available inventories for different types of EQIL studies and model development.

The soil indicator of forest health in the Forest Inventory and Analysis Program

Science.gov (United States)

Michael C. Amacher; Charles H. Perry

2010-01-01

Montreal Process Criteria and Indicators (MPCI) were established to monitor forest conditions and trends to promote sustainable forest management. The Soil Indicator of forest health was developed and implemented within the USFS Forest Inventory and Analysis (FIA) program to assess condition and trends in forest soil quality in U.S. forests regardless of ownership. The...

INVENTORY DECISIONS WITH DECREASING PURCHASING COSTS

OpenAIRE

XIANGPEI HU; HUIMIN WANG; YUNZENG WANG

2012-01-01

Costs of many items drop systematically throughout their life-cycles, due to advances in technology and competition. Motivated by the management of service parts for some high-tech products, this paper studies inventory decisions for such items. In a periodic review setting with stochastic demand, we model the purchasing costs of successive periods as a stochastic and decreasing sequence. Unit selling price of the item is determined as some mark-up of the purchasing cost and, hence, will chan...

Performance analysis of a combined organic Rankine cycle and vapor compression cycle for power and refrigeration cogeneration

International Nuclear Information System (INIS)

Kim, Kyoung Hoon; Perez-Blanco, Horacio

2015-01-01

A thermodynamic analysis of cogeneration of power and refrigeration activated by low-grade sensible energy is presented in this work. An organic Rankine cycle (ORC) for power production and a vapor compression cycle (VCC) for refrigeration using the same working fluid are linked in the analysis, including the limiting case of cold production without net electricity production. We investigate the effects of key parameters on system performance such as net power production, refrigeration, and thermal and exergy efficiencies. Characteristic indexes proportional to the cost of heat exchangers or of turbines, such as total number of transfer units (NTU tot ), size parameter (SP) and isentropic volumetric flow ratio (VFR) are also examined. Three important system parameters are selected, namely turbine inlet temperature, turbine inlet pressure, and the flow division ratio. The analysis is conducted for several different working fluids. For a few special cases, isobutane is used for a sensitivity analysis due to its relatively high efficiencies. Our results show that the system has the potential to effectively use low grade thermal sources. System performance depends both on the adopted parameters and working fluid. - Highlights: • Waste heat utilization can reduce emissions of carbon dioxide. • The ORC/VCC cycle can deliver power and/or refrigeration using waste heat. • Efficiencies and size parameters are used for cycle evaluation. • The cycle performance is studied for eight suitable refrigerants. Isobutane is used for a sensitivity analysis. • The work shows that the isobutene cycle is quite promising.

Analysis of Refrigeration Cycle Performance with an Ejector

Directory of Open Access Journals (Sweden)

Wani J. R.

2016-01-01

Full Text Available A conventional refrigeration cycle uses expansion device between the condenser and the evaporator which has losses during the expansion process. A refrigeration cycle with ejector is a promising modification to improve the performance of conventional refrigeration cycle. The ejector is used to recover some of the available work so that the compressor suction pressure increases. To investigate the enhancement a model with R134a refrigerant was developed. To solve the set of equations and simulate the cycle performance a subroutine was written on engineering equation solver (EES environment. At specific conditions, the refrigerant properties are obtained from EES. At the design conditions the ejector refrigeration cycle achieved 5.141 COP compared to 4.609 COP of the conventional refrigeration cycle. This means that ejector refrigeration cycle offers better COP with 10.35% improvement compared to conventional refrigeration cycle. Parametric analysis of ejector refrigeration cycle indicated that COP was influenced significantly by evaporator and condenser temperatures, entrainment ratio and diffuser efficiency.

The enhanced forest inventory and analysis program of the USDA forest service: historical perspective and announcements of statistical documentation

Science.gov (United States)

Ronald E. McRoberts; William A. Bechtold; Paul L. Patterson; Charles T. Scott; Gregory A. Reams

2005-01-01

The Forest Inventory and Analysis (FIA) program of the USDA Forest Service has initiated a transition from regional, periodic inventories to an enhanced national FIA program featuring annual measurement of a proportion of plots in each state, greater national consistency, and integration with the ground sampling component of the Forest Health Monitoring (FHM) program...

Equilibrium transuranic management scheme for diverse fuel cycle analysis

International Nuclear Information System (INIS)

Haas, Jason; Lee, John C.

2008-01-01

A key issue cited in the U.S. Department of Energy's report to Congress (2003) on the research path for the Advanced Fuel Cycle Initiative (AFCI) is an accurate estimation of life cycle costs for the construction, operation, decontamination and decommissioning of all fuel cycle facilities. In this report we discuss the methodology and validation of a fuel cycle model based on equilibrium operation. We apply our model to a diverse set of advanced reactors and fuel types in order to determine the most effective transmuting system while simultaneously minimizing fuel cycle costs. Our analysis shows that a nearly instant equilibrium modeling of fuel cycle scenarios can accurately approximate the detailed complex dynamic models developed by national laboratories. Our analysis also shows that the cost of transmuting Spent Nuclear Fuel (SNF) from a UO 2 fueled Pressurized Water Reactor (PWR) is minimized by utilizing the thorium cycle in sodium cooled fast reactors and is near the cost for long term repository storage of SNF at Yucca Mountain. (authors)

ARC System fuel cycle analysis capability, REBUS-2

International Nuclear Information System (INIS)

Hosteny, R.P.

1978-10-01

A detailed description is given of the ARC System fuel cycle modules FCI001, FCC001, FCC002, and FCC003 which form the fuel cycle analysis modules of the ARC System. These modules, in conjunction with certain other modules of the ARC System previously described in documents of this series, form the fuel cycle analysis system called REBUS-2. The physical model upon which the REBUS-2 fuel cycle modules are based and the calculational approach used in solving this model are discussed in detail. The REBUS-2 system either solves for the infinite time (i.e., equilibrium) operating conditions of a fuel recycle system under fixed fuel management conditions, or solves for the operating conditions during each of a series of explicitly specified (i.e., nonequilibrium) sequence of burn cycles. The code has the capability to adjust the fuel enrichment, the burn time, and the control poison requirements in order to satisfy user specified constraints on criticality, discharge fuel burnup, or to give the desired multiplication constant at some specified time during the reactor operation

ARC System fuel cycle analysis capability, REBUS-2

Energy Technology Data Exchange (ETDEWEB)

Hosteny, R.P.

1978-10-01

A detailed description is given of the ARC System fuel cycle modules FCI001, FCC001, FCC002, and FCC003 which form the fuel cycle analysis modules of the ARC System. These modules, in conjunction with certain other modules of the ARC System previously described in documents of this series, form the fuel cycle analysis system called REBUS-2. The physical model upon which the REBUS-2 fuel cycle modules are based and the calculational approach used in solving this model are discussed in detail. The REBUS-2 system either solves for the infinite time (i.e., equilibrium) operating conditions of a fuel recycle system under fixed fuel management conditions, or solves for the operating conditions during each of a series of explicitly specified (i.e., nonequilibrium) sequence of burn cycles. The code has the capability to adjust the fuel enrichment, the burn time, and the control poison requirements in order to satisfy user specified constraints on criticality, discharge fuel burnup, or to give the desired multiplication constant at some specified time during the reactor operation.

Application of life cycle assessment for an evaluation of wastewater treatment and reuse project--case study of Xi'an, China.

Science.gov (United States)

Zhang, Q H; Wang, X C; Xiong, J Q; Chen, R; Cao, B

2010-03-01

In order to illuminate the benefit of a wastewater treatment and reuse project, a life cycle assessment (LCA) model was proposed by combining the process-based LCA and the input-output based LCA in one framework and using energy consumption as the sole parameter for quantitative evaluation of the project. The life cycle consumption was evaluated mainly by life cycle inventory (LCI) analysis taking into account the construction phase, operation phase and demolishment phase of the project. For evaluating the life cycle benefit of treated water reuse, attention was paid to the decrease of secondary effluent discharge and water saving. As a result of comprehensive LCA analysis of a case project in Xi'an, China, it was understood that the life cycle benefit gained from treated wastewater reuse much surpassed the life cycle energy consumption. The advantage of wastewater treatment and reuse was well shown by LCA analysis using the proposed model. 2009 Elsevier Ltd. All rights reserved.

Municipal solid waste management health risk assessment from air emissions for China by applying life cycle analysis.

Science.gov (United States)

Li, Hua; Nitivattananon, Vilas; Li, Peng

2015-05-01

This study is to quantify and objectively evaluate the extent of environmental health risks from three waste treatment options suggested by the national municipal solid waste management enhancing strategy (No [2011] 9 of the State Council, promulgated on 19 April 2011), which includes sanitary landfill, waste-to-energy incineration and compost, together with the material recovery facility through a case study in Zhangqiu City of China. It addresses potential chronic health risks from air emissions to residential receptors in the impacted area. It combines field survey, analogue survey, design documents and life cycle inventory methods in defining the source strength of chemicals of potential concern. The modelling of life cycle inventory and air dispersion is via integrated waste management(IWM)-2 and Screening Air Dispersion Model (Version 3.0) (SCREEN3). The health risk assessment is in accordance with United States Environmental Protection Agency guidance Risk Assessment Guidance for Superfund (RAGS), Volume I: Human Health Evaluation Manual (Part F, Supplemental Guidance for Inhalation Risk Assessment). The exposure concentration is based on long-term exposure to the maximum ground level contaminant in air under the 'reasonable worst situation' emissions and then directly compared with reference for concentration and unit risk factor/cancer slope factor derived from the national air quality standard (for a conventional pollutant) and toxicological studies (for a specific pollutant). Results from this study suggest that the option of compost with material recovery facility treatment may pose less negative health impacts than other options; the sensitivity analysis shows that the landfill integrated waste management collection rate has a great influence on the impact results. Further investigation is needed to validate or challenge the findings of this study. © The Author(s) 2015.

Optimization of Inventory

OpenAIRE

PROKOPOVÁ, Nikola

2017-01-01

The subject of this thesis is optimization of inventory in selected organization. Inventory optimization is a very important topic in each organization because it reduces storage costs. At the beginning the inventory theory is presented. It shows the meaning and types of inventory, inventory control and also different methods and models of inventory control. Inventory optimization in the enterprise can be reached by using models of inventory control. In the second part the company on which is...

Life cycle costs for Alaska bridges.

Science.gov (United States)

2014-08-01

A study was implemented to assist the Alaska Department of Transportation and Public Facilities (ADOT&PF) with life cycle costs for : the Alaska Highway Bridge Inventory. The study consisted of two parts. Part 1 involved working with regional offices...

Forest Inventory and Analysis in the United States: Remote sensing and geospatial activities

Science.gov (United States)

Mark Nelson; Gretchen Moisen; Mark Finco

2007-01-01

Our Nation's forests provide a wealth of ecological, social, and economic resources. These forest lands cover over 300 million hectares of the United States, or about one third of the total land area. Accurate and timely information about them is essential to their wise management and use. The mission of the Forest Service's Forest Inventory and Analysis (FIA...

Use of dwell time concept in fission product inventory assessment for CANDU reactors

International Nuclear Information System (INIS)

Bae, C.J.; Choi, J.H.; Hwang, H.R.; Seo, J.T.

2003-01-01

A realistic approach in calculating the initial fission product inventory within the CANFLEX-NU fuel has been assessed for its applicability to the single channel event safety analysis for CANDU reactors. This approach is based on the dwell time concept in which the accident is assumed to occur at the dwell time when the summation of fission product inventory for all isotopes becomes largest. However, in the current conservative analysis, the maximum total inventory and the corresponding gap inventory for each isotope are used as the initial fission product inventories regardless of the accident initiation time. The fission product inventory analysis has been performed using ELESTRES code considering power histories and burnup of the fuel bundles in the limiting channel. The analysis results showed that the total fission product inventory is found to be largest at 20% dwell time. Therefore, the fission product inventory at 20% dwell time can be used as the initial condition for the single channel event for the CANDU 6 reactors. (author)

Inventory Abstraction

International Nuclear Information System (INIS)

Leigh, C.

2000-01-01

The purpose of the inventory abstraction as directed by the development plan (CRWMS M and O 1999b) is to: (1) Interpret the results of a series of relative dose calculations (CRWMS M and O 1999c, 1999d). (2) Recommend, including a basis thereof, a set of radionuclides that should be modeled in the Total System Performance Assessment in Support of the Site Recommendation (TSPA-SR) and the Total System Performance Assessment in Support of the Final Environmental Impact Statement (TSPA-FEIS). (3) Provide initial radionuclide inventories for the TSPA-SR and TSPA-FEIS models. (4) Answer the U.S. Nuclear Regulatory Commission (NRC)'s Issue Resolution Status Report ''Key Technical Issue: Container Life and Source Term'' (CLST IRSR) (NRC 1999) key technical issue (KTI): ''The rate at which radionuclides in SNF [Spent Nuclear Fuel] are released from the EBS [Engineered Barrier System] through the oxidation and dissolution of spent fuel'' (Subissue 3). The scope of the radionuclide screening analysis encompasses the period from 100 years to 10,000 years after the potential repository at Yucca Mountain is sealed for scenarios involving the breach of a waste package and subsequent degradation of the waste form as required for the TSPA-SR calculations. By extending the time period considered to one million years after repository closure, recommendations are made for the TSPA-FEIS. The waste forms included in the inventory abstraction are Commercial Spent Nuclear Fuel (CSNF), DOE Spent Nuclear Fuel (DSNF), High-Level Waste (HLW), naval Spent Nuclear Fuel (SNF), and U.S. Department of Energy (DOE) plutonium waste. The intended use of this analysis is in TSPA-SR and TSPA-FEIS. Based on the recommendations made here, models for release, transport, and possibly exposure will be developed for the isotopes that would be the highest contributors to the dose given a release to the accessible environment. The inventory abstraction is important in assessing system performance because

Waste-to-energy: A review of life cycle assessment and its extension methods.

Science.gov (United States)

Zhou, Zhaozhi; Tang, Yuanjun; Chi, Yong; Ni, Mingjiang; Buekens, Alfons

2018-01-01

This article proposes a comprehensive review of evaluation tools based on life cycle thinking, as applied to waste-to-energy. Habitually, life cycle assessment is adopted to assess environmental burdens associated with waste-to-energy initiatives. Based on this framework, several extension methods have been developed to focus on specific aspects: Exergetic life cycle assessment for reducing resource depletion, life cycle costing for evaluating its economic burden, and social life cycle assessment for recording its social impacts. Additionally, the environment-energy-economy model integrates both life cycle assessment and life cycle costing methods and judges simultaneously these three features for sustainable waste-to-energy conversion. Life cycle assessment is sufficiently developed on waste-to-energy with concrete data inventory and sensitivity analysis, although the data and model uncertainty are unavoidable. Compared with life cycle assessment, only a few evaluations are conducted to waste-to-energy techniques by using extension methods and its methodology and application need to be further developed. Finally, this article succinctly summarises some recommendations for further research.

Developing Green GDP Accounting for Thai Agricultural Sector Using the Economic Input Output - Life Cycle Assessment to Assess Green Growth

OpenAIRE

Attavanich, Witsanu; Mungkung, Rattanawan; Mahathanaseth, Itthipong; Sanglestsawai, Santi; Jirajari, Athiwatr

2016-01-01

There is no indicator measuring Thailand’s green growth by valuing the resource degradation and environmental damage costs. This article aims to estimate Thailand’s green gross domestic (GDP) that takes into account environmental damage costs with the detailed analysis on the agricultural sector using the Economic Input Output - Life Cycle Assessment (EIO-LCA) approach. The representative product in each sector was selected based on the available life cycle inventory data, economic values and...

The construct validity of the Major Depression Inventory: A Rasch analysis of a self-rating scale in primary care.

Science.gov (United States)

Nielsen, Marie Germund; Ørnbøl, Eva; Vestergaard, Mogens; Bech, Per; Christensen, Kaj Sparle

2017-06-01

We aimed to assess the measurement properties of the ten-item Major Depression Inventory when used on clinical suspicion in general practice by performing a Rasch analysis. General practitioners asked consecutive persons to respond to the web-based Major Depression Inventory on clinical suspicion of depression. We included 22 practices and 245 persons. Rasch analysis was performed using RUMM2030 software. The Rasch model fit suggests that all items contribute to a single underlying trait (defined as internal construct validity). Mokken analysis was used to test dimensionality and scalability. Our Rasch analysis showed misfit concerning the sleep and appetite items (items 9 and 10). The response categories were disordered for eight items. After modifying the original six-point to a four-point scoring system for all items, we achieved ordered response categories for all ten items. The person separation reliability was acceptable (0.82) for the initial model. Dimensionality testing did not support combining the ten items to create a total score. The scale appeared to be well targeted to this clinical sample. No significant differential item functioning was observed for gender, age, work status and education. The Rasch and Mokken analyses revealed two dimensions, but the Major Depression Inventory showed fit to one scale if items 9 and 10 were excluded. Our study indicated scalability problems in the current version of the Major Depression Inventory. The conducted analysis revealed better statistical fit when items 9 and 10 were excluded. Copyright © 2017 Elsevier Inc. All rights reserved.

Joint inventory control and pricing in a service-inventory system

DEFF Research Database (Denmark)

Marand, Ata Jalili; Li, Hongyan Jenny; Thorstenson, Anders

2017-01-01

This study addresses joint inventory control and pricing decisions for a service-inventory system. In such a system both an on-hand inventory item and a positive service time are required to fulfill customer demands. The service-inventory system also captures main features of the classical...... inventory systems with a positive processing time, e.g., make-to-order systems. In this study, the service-inventory system is modeled as an M/M/1 queue in which the customer arrival rate is price dependent. The inventory of an individual item is continuously reviewed under an (r,Q) policy....... The replenishment lead times of the inventory are exponentially distributed. Furthermore, customers arriving during stock-out periods are lost. The stochastic customer inter-arrival times, service times, and inventory replenishment lead times cause the high complexity of the problem and the difficulty in solving it...

Applying unit process life cycle inventor (UPLCI) methodology in product/packaging combinatons

NARCIS (Netherlands)

Oude Luttikhuis, Ellen; Toxopeus, Marten E.; Overcash, M.; Nee, Andrew Y.C.; Song, Bin; Ong, Soh-Khim

2013-01-01

This paper discusses how the UPLCI approach can be used for determining the inventory of the manufacturing phases of product/packaging combinations. The UPLCI approach can make the inventory of the manufacturing process of the product that is investigated more accurate. The life cycle of

Model of inventory replenishment in periodic review accounting for the occurrence of shortages

Directory of Open Access Journals (Sweden)

Stanisław Krzyżaniak

2014-03-01

Full Text Available Background: Despite the development of alternative concepts of goods flow management, the inventory management under conditions of random variations of demand is still an important issue, both from the point of view of inventory keeping and replenishment costs and the service level measured as the level of inventory availability. There is a number of inventory replenishment systems used in these conditions, but they are mostly developments of two basic systems: reorder point-based and periodic review-based. The paper deals with the latter system. Numerous researches indicate the need to improve the classical models describing that system, the reason being mainly the necessity to adapt the model better to the actual conditions. This allows a correct selection of parameters that control the used inventory replenishment system and - as a result - to obtain expected economic effects. Methods: This research aimed at building a model of the periodic review system to reflect the relations (observed during simulation tests between the volume of inventory shortages and the degree of accounting for so-called deferred demand, and the service level expressed as the probability of satisfying the demand in the review and the inventory replenishment cycle. The following model building and testing method has been applied: numerical simulation of inventory replenishment - detailed analysis of simulation results - construction of the model taking into account the regularities observed during the simulations - determination of principles of solving the system of relations creating the model - verification of the results obtained from the model using the results from simulation. Results: Presented are selected results of calculations based on classical formulas and using the developed model, which describe the relations between the service level and the parameters controlling the discussed inventory replenishment system. The results are compared to the simulation

Dealing with Emergy Algebra in the Life Cycle Assessment Framework

Science.gov (United States)

The Life Cycle Inventory (LCI) represents one of the four steps of the Life Cycle Assessment (LCA) methodology, which is a standardized procedure (ISO 14040:2006) to estimate the environmental impacts generated by the production, use and disposal of goods and services. In this co...

Development of computer software for pavement life cycle cost analysis.

Science.gov (United States)

1988-01-01

The life cycle cost analysis program (LCCA) is designed to automate and standardize life cycle costing in Virginia. It allows the user to input information necessary for the analysis, and it then completes the calculations and produces a printed copy...

KWIKPLAN: a computer program for projecting the annual requirements of nuclear fuel cycle operations

International Nuclear Information System (INIS)

Salmon, R.; Kee, C.W.

1977-06-01

The computer code KWIKPLAN was written to facilitate the calculation of projected nuclear fuel cycle activities. Using given projections of power generation, the code calculates annual requirements for fuel fabrication, fuel reprocessing, uranium mining, and plutonium use and production. The code uses installed capacity projections and mass flow data for six types of reactors to calculate projected fuel cycle activities and inventories. It calculates fissile uranium and plutonium flows and inventories after allowing for an economy with limited reprocessing capacity and a backlog of unreprocessed fuel. All calculations are made on a quarterly basis; printed and punched output of the projected fuel cycle activities are made on an annual basis. Since the punched information is used in another code to determine waste inventories, the code punches a table from which the effective average burnup can be calculated for the fuel being reprocessed

A Study on Degree of Conservatism of PZR Inventory during Event Analysis

International Nuclear Information System (INIS)

Lee, Sang Seob; Park, Min Soo; Huh, Jae Yong; Lee, Gyu Cheon

2016-01-01

The pressurizer safety valves (PSVs) are installed in OPR1000 plants. While the pressurizer pilot operated safety relief valve (POSRV) of APR1400 is designed to discharge steam and/or water, the PSV is designed to discharge steam only. To check degree of conservatism of a PZR water level during PSV operation, a study has been performed using a computer code, RELAP5/ MOD3.3. Degree of conservatism is described herein, and the results are shown to evaluate degree of conservatism. Degree of conservatism is evaluated with respect to the PZR inventory for OPR1000 plant. It could be concluded that there is no possibility the liquid goes through PSVs during PLCS malfunction, because the expected maximum PZR inventory would remain below PSV nozzle based on the conservative assumptions. With the site specific PSV characteristics, a degree of conservatism would be determined to guarantee the PSV integrity during the event. To guarantee the PSV integrity, an independent analysis is recommended

A Study on Degree of Conservatism of PZR Inventory during Event Analysis

Energy Technology Data Exchange (ETDEWEB)

Lee, Sang Seob; Park, Min Soo; Huh, Jae Yong; Lee, Gyu Cheon [KEPCO Engineering and Construction Co. Ltd., Deajeon (Korea, Republic of)

2016-10-15

The pressurizer safety valves (PSVs) are installed in OPR1000 plants. While the pressurizer pilot operated safety relief valve (POSRV) of APR1400 is designed to discharge steam and/or water, the PSV is designed to discharge steam only. To check degree of conservatism of a PZR water level during PSV operation, a study has been performed using a computer code, RELAP5/ MOD3.3. Degree of conservatism is described herein, and the results are shown to evaluate degree of conservatism. Degree of conservatism is evaluated with respect to the PZR inventory for OPR1000 plant. It could be concluded that there is no possibility the liquid goes through PSVs during PLCS malfunction, because the expected maximum PZR inventory would remain below PSV nozzle based on the conservative assumptions. With the site specific PSV characteristics, a degree of conservatism would be determined to guarantee the PSV integrity during the event. To guarantee the PSV integrity, an independent analysis is recommended.

An economic analysis code used for PWR fuel cycle

International Nuclear Information System (INIS)

Liu Dingqin

1989-01-01

An economic analysis code used for PWR fuel cycle is developed. This economic code includes 12 subroutines representing vavious processes for entire PWR fuel cycle, and indicates the influence of the fuel cost on the cost of the electricity generation and the influence of individual process on the sensitivity of the fuel cycle cost

The estimation and prediction of the inventories for the liquid and gaseous radwaste systems using the linear regression analysis

International Nuclear Information System (INIS)

Kim, J. Y.; Shin, C. H.; Kim, J. K.; Lee, J. K.; Park, Y. J.

2003-01-01

The variation transitions of the inventories for the liquid radwaste system and the radioactive gas have being released in containment, and their predictive values according to the operation histories of Yonggwang(YGN) 3 and 4 were analyzed by linear regression analysis methodology. The results show that the variation transitions of the inventories for those systems are linearly increasing according to the operation histories but the inventories released to the environment are considerably lower than the recommended values based on the FSAR suggestions. It is considered that some conservation were presented in the estimation methodology in preparing stage of FSAR

Global gridded anthropogenic emissions inventory of carbonyl sulfide

Science.gov (United States)

Zumkehr, Andrew; Hilton, Tim W.; Whelan, Mary; Smith, Steve; Kuai, Le; Worden, John; Campbell, J. Elliott

2018-06-01

Atmospheric carbonyl sulfide (COS or OCS) is the most abundant sulfur containing gas in the troposphere and is an atmospheric tracer for the carbon cycle. Gridded inventories of global anthropogenic COS are used for interpreting global COS measurements. However, previous gridded anthropogenic data are a climatological estimate based on input data that is over three decades old and are not representative of current conditions. Here we develop a new gridded data set of global anthropogenic COS sources that includes more source sectors than previously available and uses the most current emissions factors and industry activity data as input. Additionally, the inventory is provided as annually varying estimates from years 1980-2012 and employs a source specific spatial scaling procedure. We estimate a global source in year 2012 of 406 Gg S y-1 (range of 223-586 Gg S y-1), which is highly concentrated in China and is twice as large as the previous gridded inventory. Our large upward revision in the bottom-up estimate of the source is consistent with a recent top-down estimate based on air-monitoring and Antarctic firn data. Furthermore, our inventory time trends, including a decline in the 1990's and growth after the year 2000, are qualitatively consistent with trends in atmospheric data. Finally, similarities between the spatial distribution in this inventory and remote sensing data suggest that the anthropogenic source could potentially play a role in explaining a missing source in the global COS budget.

Integrating forest inventory and analysis data into a LIDAR-based carbon monitoring system

Science.gov (United States)

Kristofer D. Johnson; Richard Birdsey; Andrew O Finley; Anu Swantaran; Ralph Dubayah; Craig Wayson; Rachel. Riemann

2014-01-01

Forest Inventory and Analysis (FIA) data may be a valuable component of a LIDAR-based carbon monitoring system, but integration of the two observation systems is not without challenges. To explore integration methods, two wall-to-wall LIDAR-derived biomass maps were compared to FIA data at both the plot and county levels in Anne Arundel and Howard Counties in Maryland...

LIFE CYCLE ASSESSMENT PILIHAN PENGELOLAAN SAMPAH : STUDI KASUS WILAYAH KARTAMANTUL PROPINSI D.I. YOGYAKARTA (Life Cycle Assessment of Solid Waste Management Options : Case Study of the KARTAMANTUL Regions, Province of D.I.Yogyakarta

Directory of Open Access Journals (Sweden)

Made Gunamantba

2010-07-01

system options. The functional unit of the study was the ammount of solid waste managed. The life cycle inventory analysis carried out by including the assumtions made for each processes in the SWM system. Energy production and inventory emissions were calculated and classified in to impact categories; global warming, acidification, eutrophication, and photochemical oxidant. Impact categories indicator were quantified with equivalence factors of relevan emissions to develope the environmental profiles of each scenario. In most of the categories, direct gasification was found to be the most feasible method, except the acidification. Sensitivity analysis has been used to test some of the assumptions used in the influence of variety input to the results but none have effect on the overall result. Therefore, the best alternative to the existing SWM can be identified.

The USA Nr Inventory: Dominant Sources and Primary Transport Pathways

Science.gov (United States)

Sabo, R. D.; Clark, C.; Sobota, D. J.; Compton, J.; Cooter, E. J.; Schwede, D. B.; Bash, J. O.; Rea, A.; Dobrowolski, J. P.

2016-12-01

Efforts to mitigate the deleterious effects of excess reactive nitrogen (Nr) on human health and ecosystem goods and service while ensuring food, biofuel, and fiber availability, is one of the most pressing environmental management challenges of this century. Effective management of Nr requires up to date inventories that quantitatively characterize the sources, transport, and transformation of Nr through the environment. The inherent complexity of the nitrogen cycle, however, through multiple exchange points across air, water, and terrestrial media, renders such inventories difficult to compile and manage. Previous Nr Inventories are for 2002 and 2007, and used data sources that have since been improved. Thus, this recent inventory will substantially advance the methodology across many sectors of the inventory (e.g. deposition and biological fixation in crops and natural systems) and create a recent snapshot that is sorely needed for policy planning and trends analysis. Here we use a simple mass balance approach to estimate the input-output budgets for all United States Geologic Survey Hydrologic Unit Code-8 watersheds. We focus on a recent year (i.e. 2012) to update the Nr Inventory, but apply the analytical approach for multiple years where possible to assess trends through time. We also compare various sector estimates using multiple methodologies. Assembling datasets that account for new Nr inputs into watersheds (e.g., atmospheric NOy deposition, food imports, biologic N fixation) and internal fluxes of recycled Nr (e.g., manure, Nr emmissions/volatilization) provide an unprecedented, data driven computation of N flux. Input-output budgets will offer insight into 1) the dominant sources of Nr in a watershed (e.g., food imports, atmospheric N deposition, or fertilizer), 2) the primary loss pathways for Nr (e.g., crop N harvest, volatilization/emissions), and 3) what watersheds are net sources versus sinks of Nr. These insights will provide needed clarity for

Life cycle inventory for the production of germinated oil palm seeds at a selected seed production unit in Malaysia

Science.gov (United States)

Khairuddin, Nik Sasha Khatrina; Ismail, B. S.; Muhamad, Halimah; May, Choo Yuen

2013-11-01

The increasing global demand for edible oil has encouraged Malaysia to increase the areas under oil palm cultivation. The total demand for germinated oil palm seeds in the years 2009, 2010, 2011 and 2012 were 86.4, 76.5, 72.6 and 75.2 million, respectively. Production of germinated oil palm seeds is the first link in the palm oil supply chain. Therefore, good management practices at seed production stage is required to ensure only high quality germinated oil palm seeds are produced before sale to customers. Life cycle assessment (LCA) has been used as a tool to assess environmental impact of the processes throughout a product's lifespan and this approach is an important tool for assessing green house gas (GHG) emission. For this study, a gate-to-gate life cycle inventory (LCI) of a single germinated oil palm seed production unit was carried out. The functional unit used for this LCI was one germinated oil palm seed. To determine the environmental impact for the production of germinated oil palm seeds, information on the inputs were obtained. The inputs for the production of germinated oil palm seeds involved materials such as polyethylene bags, electricity, water, chemicals and fungicides. For this study, the system boundary involved seed germination process and management of germinated oil palm seeds. It was found that the amount of input such as materials and energy used in the production of germinated oil palm seeds was very minimal.

Economic Analysis of Different Nuclear Fuel Cycle Options

International Nuclear Information System (INIS)

Ko, W.; Gao, F.

2012-01-01

An economic analysis has been performed to compare four nuclear fuel cycle options: a once-through cycle (OT), DUPIC recycling, thermal recycling using MOX fuel in a pressurized water reactor (PWR-MOX), and sodium fast reactor recycling employing pyro processing (Pyro-SFR). This comparison was made to suggest an economic competitive fuel cycle for the Republic of Korea. The fuel cycle cost (FCC) has been calculated based on the equilibrium material flows integrated with the unit cost of the fuel cycle components. The levelized fuel cycle costs (LFCC) have been derived in terms of mills/kWh for a fair comparison among the FCCs, and the results are as follows: OT 7.35 mills/kWh, DUPIC 9.06 mills/kWh, PUREX-MOX 8.94 mills/kWh, and Pyro-SFR 7.70 mills/kWh. Due to unavoidable uncertainties, a cost range has been applied to each unit cost, and an uncertainty study has been performed accordingly. A sensitivity analysis has also been carried out to obtain the break-even uranium price (215$/kgU) for the Pyro-SFR against the OT, which demonstrates that the deployment of the Pyro-SFR may be economical in the foreseeable future. The influence of pyro techniques on the LFCC has also been studied to determine at which level the potential advantages of Pyro-SFR can be realized.

An Inquiry into the Life Cycle of Systems of Inner Walls: Comparison of Masonry and Drywall

Directory of Open Access Journals (Sweden)

Karina Condeixa

2015-06-01

Full Text Available Life Cycle Assessment is a methodology that investigates impacts linked to a product or service during its entire life cycle. Life Cycle Assessment studies investigate processes and sub-processes in a fragmented way to ascertain their inputs, outputs and emissions and get an overview of the generating sources of their environmental loads. The lifecycle concept involves all direct and indirect processes of the studied object. This article aims to model the material flows in the masonry and drywall systems and internal walls in a Brazilian scenario, and calculate the climate change impacts generated by the transport of the component materials of the systems. Internal walls of a residential dwelling in Rio de Janeiro are analyzed from a qualitative inventory of all life cycles with an analysis of material flows, based on technical and academic literature. All Life Cycle Impact Assessment of the systems is carried out with international data from the database, and using the IPCC2013 method for climate change impacts. This study disregards the refurbishment and possible extensions within the use phase. Thus, the inventory identifies weaknesses of the systems while the impact assessment validates the results. This study allows us a complete understanding about the inner walls systems in the Brazilian scenario, evidencing its main weaknesses and subsidizes decision-making for the industry and for planning of the new buildings.

Nuclear Fuel Cycle System Analysis (II)

Energy Technology Data Exchange (ETDEWEB)

Ko, Won Il; Kwon, Eun Ha; Yoon, Ji Sup; Park, Seong Won

2007-04-15

As a nation develops strategies that provide nuclear energy while meeting its various objectives, it must begin with identification of a fuel cycle option that can be best suitable for the country. For such a purpose, this paper takes four different fuel cycle options that are likely adopted by the Korean government, considering the current status of nuclear power generation and the 2nd Comprehensive Nuclear Energy Promotion Plan (CNEPP) - Once-through Cycle, DUPIC Recycle, Thermal Reactor Recycle and GEN-IV Recycle. The paper then evaluates each option in terms of sustainability, environment-friendliness, proliferation-resistance, economics and technologies. Like all the policy decision, however, a nuclear fuel cycle option can not be superior in all aspects of sustainability, environment-friendliness, proliferation-resistance, economics, technologies and so on, which makes the comparison of the options extremely complicated. Taking this into consideration, the paper analyzes all the four fuel cycle options using the Multi-Attribute Utility Theory (MAUT) and the Analytic Hierarchy Process (AHP), methods of Multi-Attribute Decision Making (MADM), that support systematical evaluation of the cases with multi- goals or criteria and that such goals are incompatible with each other. The analysis shows that the GEN-IV Recycle appears to be most competitive.

Economic analysis of fast reactor fuel cycle with different modes

International Nuclear Information System (INIS)

Ding Xiaoming

2014-01-01

Because of limitations on the access to technical and economic data and the lack of effective verification, the lack of in-depth study on the economy of fast reactor fuel cycle in China. This paper introduces the analysis and calculation results of the levelized cost of electricity (LCOE) under three different fuel cycle modes including fast reactor fuel cycle carried out by Massachusetts Institute of Technology (MIT). The author used the evaluation method and hypothesis parameters provided by the MIT to carry out the sensitivity analysis for the impact of the overnight cost, the discount rate and changes of uranium price on the LCOE under three fuel cycle modes. Finally, some suggestions are proposed on the study of economy in China's fast reactor fuel cycle. (authors)

A review of battery life-cycle analysis : state of knowledge and critical needs.

Energy Technology Data Exchange (ETDEWEB)

Sullivan, J. L.; Gaines, L.; Energy Systems

2010-12-22

A literature review and evaluation has been conducted on cradle-to-gate life-cycle inventory studies of lead-acid, nickel-cadmium, nickel-metal hydride, sodium-sulfur, and lithium-ion battery technologies. Data were sought that represent the production of battery constituent materials and battery manufacture and assembly. Life-cycle production data for many battery materials are available and usable, though some need updating. For the remaining battery materials, lifecycle data either are nonexistent or, in some cases, in need of updating. Although battery manufacturing processes have occasionally been well described, detailed quantitative information on energy and material flows is missing. For all but the lithium-ion batteries, enough constituent material production energy data are available to approximate material production energies for the batteries, though improved input data for some materials are needed. Due to the potential benefit of battery recycling and a scarcity of associated data, there is a critical need for life-cycle data on battery material recycling. Either on a per kilogram or per watt-hour capacity basis, lead-acid batteries have the lowest production energy, carbon dioxide emissions, and criteria pollutant emissions. Some process-related emissions are also reviewed in this report.

Erikson Psychosocial Stage Inventory: A Factor Analysis

Science.gov (United States)

Gray, Mary McPhail; And Others

1986-01-01

The 72-item Erikson Psychosocial Stage Inventory (EPSI) was factor analyzed for a group of 534 university freshmen and sophomore students. Seven factors emerged, which were labeled Initiative, Industry, Identity, Friendship, Dating, Goal Clarity, and Self-Confidence. Item's representing Erikson's factors, Trust and Autonomy, were dispersed across…

[Development of the Coparental Regulation Inventory and cross-sectional analysis of mothers' encouragement and criticism].

Science.gov (United States)

Kato, Michiyo; Kurosawa, Tai; Kamiya, Tetsuji

2014-02-01

We developed the Coparental Regulation Inventory to assess the regulatory behavior of the mothers in involving fathers with child rearing. We translated and modified the short form of the Parental Regulation Inventory (PRI) for Japanese couples in different stages of child rearing. An online questionnaire was conducted with mothers (n = 500) and fathers (n = 500) whose youngest child was less than 21-years-old. Exploratory factor analysis identified two factors, which were labeled "encouragement" and "criticism". The resulting Coparental Regulation Inventory (the modified PRI) had high internal consistency and test-retest reliability. The construct validity of the scale was supported by its correlation with parenting alliance, marital satisfaction, and the father's involvement. These findings suggest that the scale is an adequate instrument for identifying the behaviors of mothers related to coparenting. In addition, we examined the frequency of encouragement and criticism used by the mother in relation to the child-rearing stage using cross-sectional analysis. In the mothers' reports, mothers with infants and children encouraged fathers more than mothers with early and late adolescents. Mothers with late adolescents criticized fathers less than mothers with infants. In the fathers' reports, mothers gave more encouragement to fathers who had infants than at any other age, whereas the child's age was not related to mothers' criticism perceived by the fathers.

A tool to determine crown and plot canopy transparency for forest inventory and analysis phase 3 plots using digital photographs

Science.gov (United States)

Matthew F. Winn; Philip A. Araman

2012-01-01

The USDA Forest Service Forest Inventory and Analysis (FIA) program collects crown foliage transparency estimates for individual trees on Phase 3 (P3) inventory plots. The FIA crown foliage estimate is obtained from a pair of perpendicular side views of the tree. Researchers with the USDA Forest Service Southern Research Station have developed a computer program that...

Understory vegetation data quality assessment for the Interior West Forest and Inventory Analysis program

Science.gov (United States)

Paul L. Patterson; Renee A. O' Brien

2011-01-01

The Interior West Forest Inventory and Analysis (IW-FIA) program of the USDA Forest Service collects field data on understory vegetation structure that have broad applications. In IW-FIA one aspect of quality assurance is assessed based on the repeatability of field measurements. The understory vegetation protocol consists of two suites of measurements; (1) the...

Dynamic model of the global iodine cycle for the estimation of dose to the world population from releases of iodine-129 to the environment

International Nuclear Information System (INIS)

Kocher, D.C.

1979-11-01

A dynamic linear compartment model of the global iodine cycle has been developed for the purpose of estimating long-term doses and dose commitments to the world population from releases of 129 I to the environment. The environmental compartments assumed in the model comprise the atmosphere, hydrosphere, lithosphere, and terrestrial biosphere. The global transport of iodine is described by means of time-invariant fractional transfer rates between the environmental compartments. The fractional transfer rates for 129 I are determined primarily from available data on compartment inventories and fluxes for naturally occurring stable iodine and from data on the global hydrologic cycle. The dose to the world population is estimated from the calculated compartment inventories of 129 I, the known compartment inventories of stable iodine, a pathway analysis of the intake of iodine by a reference individual, dose conversion factors for inhalation and ingestion, and an estimate of the world population. For an assumed constant population of 12.21 billion beyond the year 2075, the estimated population dose commitment is 2 x 10 5 man-rem/Ci. The sensitivity of the calculated doses to variations in some of the parameters in the model for the global iodine cycle is investigated. A computer code written to calculate global compartment inventories and dose rates and population doses is described and documented

The association of bicycle-related genital numbness and Sexual Health Inventory for Men (SHIM) score: results from a large, multinational, cross-sectional study.

Science.gov (United States)

Baradaran, Nima; Awad, Mohannad; Gaither, Thomas W; Fergus, Kirkpatrick B; Ndoye, Medina; Cedars, Benjamin E; Balakrishnan, Ashwin S; Eisenberg, Michael L; Sanford, Tom; Breyer, Benjamin N

2018-05-23

To assess the association of genital numbness and erectile dysfunction in male cyclists. Cyclists were recruited through Facebook advertisements and outreach to sporting clubs. This is a secondary analysis of a larger epidemiological population-based study that examined sexual and urinary wellness in athletes. We queried cycling habits and erectile function using Sexual Health Inventory for Men (SHIM). A total of 2 774 male cyclists were included in the analysis. Amongst cyclists, there was a statistically significant increase in the trend of genital numbness presence with more years of cycling (P = 0.002), more frequent weekly cycling (P biking intensity. Cyclists report genital numbness in proportion with biking intensity but numbness is not associated with worse sexual function in this cohort. © 2018 The Authors BJU International © 2018 BJU International Published by John Wiley & Sons Ltd.

The 2014 tanana inventory pilot: A USFS-NASA partnership to leverage advanced remote sensing technologies for forest inventory

Science.gov (United States)

Hans-Erik Andersen; Chad Babcock; Robert Pattison; Bruce Cook; Doug Morton; Andrew. Finley

2015-01-01

Interior Alaska (approx. 112 million forested acres in size) is the last remaining forested area within the United States where the Forest Inventory and Analysis (FIA) program is not currently implemented. A joint NASA-FIA inventory pilot project was carried out in 2014 to increase familiarity with interior Alaska logistics and evaluate the utility of state-of-the-art...

Application of stochastic approach based on Monte Carlo (MC) simulation for life cycle inventory (LCI) to the steel process chain: case study.

Science.gov (United States)

Bieda, Bogusław

2014-05-15

The purpose of the paper is to present the results of application of stochastic approach based on Monte Carlo (MC) simulation for life cycle inventory (LCI) data of Mittal Steel Poland (MSP) complex in Kraków, Poland. In order to assess the uncertainty, the software CrystalBall® (CB), which is associated with Microsoft® Excel spreadsheet model, is used. The framework of the study was originally carried out for 2005. The total production of steel, coke, pig iron, sinter, slabs from continuous steel casting (CSC), sheets from hot rolling mill (HRM) and blast furnace gas, collected in 2005 from MSP was analyzed and used for MC simulation of the LCI model. In order to describe random nature of all main products used in this study, normal distribution has been applied. The results of the simulation (10,000 trials) performed with the use of CB consist of frequency charts and statistical reports. The results of this study can be used as the first step in performing a full LCA analysis in the steel industry. Further, it is concluded that the stochastic approach is a powerful method for quantifying parameter uncertainty in LCA/LCI studies and it can be applied to any steel industry. The results obtained from this study can help practitioners and decision-makers in the steel production management. Copyright © 2013 Elsevier B.V. All rights reserved.

A Joint Replenishment Inventory Model with Lost Sales

Science.gov (United States)

Devy, N. L.; Ai, T. J.; Astanti, R. D.

2018-04-01

This paper deals with two items joint replenishment inventory problem, in which the demand of each items are constant and deterministic. Inventory replenishment of items is conducted periodically every T time intervals. Among of these replenishments, joint replenishment of both items is possible. It is defined that item i is replenished every ZiT time intervals. Replenishment of items are instantaneous. All of shortages are considered as lost sales. The maximum allowance for lost sales of item i is Si. Mathematical model is formulated in order to determining the basic time cycle T, replenishment multiplier Zi , and maximum lost sales Si in order to minimize the total cost per unit time. A solution methodology is proposed for solve the model and a numerical example is provided for demonstrating the effectiveness of the proposed methodology.

Effect of inventory method on niche models: random versus systematic error

Science.gov (United States)

Heather E. Lintz; Andrew N. Gray; Bruce McCune

2013-01-01

Data from large-scale biological inventories are essential for understanding and managing Earth's ecosystems. The Forest Inventory and Analysis Program (FIA) of the U.S. Forest Service is the largest biological inventory in North America; however, the FIA inventory recently changed from an amalgam of different approaches to a nationally-standardized approach in...

Analysis of thorium and uranium fuel cycles in an iso-breeder lead fast reactor using extended-EQL3D procedure

International Nuclear Information System (INIS)

Fiorina, Carlo; Krepel, Jiri; Cammi, Antonio; Franceschini, Fausto; Mikityuk, Konstantin; Ricotti, Marco Enrico

2013-01-01

Highlights: ► Extension of EQL3D procedure to calculate radio-toxicity and decay heat. ► Characterization of uranium- and thorium-fueled LFR from BOL to equilibrium. ► Safety improvements for a LFR in a closed thorium cycle. ► Advantages of thorium-fueled LFR in terms of decay heat and radio-toxicity generation. ► Safety, decay heat and radio-toxicity concerns for a Th–Pu beginning-of-life core. - Abstract: Use of thorium in fast reactors has typically been considered as a secondary option, mainly thanks to a possible self-sustaining thorium cycle already in thermal reactors and due to the limited breeding capabilities compared to U–Pu in the fast neutron energy range. In recent years nuclear waste management has become more important, and the thorium option has been reconsidered for the claimed potential to burn transuranic waste and the lower build-up of hazardous isotopes in a closed cycle. To ascertain these claims and their limitations, the fuel cycle isotopic inventory, and associated waste radio-toxicity and decay heat, should be quantified and compared to the case of the uranium cycle using realistic core configurations, with complete recycle of all the actinides. Since the transition from uranium to thorium fuel cycles will likely involve a transuranic burning phase, this transition and the challenges that the evolving fuel actinide composition presents, for instance on reactor feedback parameters, should also be analyzed. In the present paper, these issues are investigated based on core physics analysis of the Lead-cooled Fast Reactor ELSY, performed with the fast reactor ERANOS code and the EQL3D procedure allowing full-core characterization of the equilibrium cycle and the transition cycles. In order to compute radio-toxicity and decay heat, EQL3D has been extended by developing a new module, which has been assessed against ORIGEN-S and is presented here. The capability of the EQL3D procedure to treat full-core 3D geometries allowed to

Compatibility analysis of DUPIC fuel (part5) - DUPIC fuel cycle economics analysis

Energy Technology Data Exchange (ETDEWEB)

Ko, Won Il; Choi, Hang Bok; Yang, Myung Seung

2000-08-01

This study examines the economics of the DUPIC fuel cycle using unit costs of fuel cycle components estimated based on conceptual designs. The fuel cycle cost (FCC) was calculated by a deterministic method in which reference values of fuel cycle components are used. The FCC was then analyzed by a Monte Carlo simulation to get the uncertainty of the FCC associated with the unit costs of the fuel cycle components. From the deterministic analysis on the one-batch equilibrium fuel cycle model, the DUPIC FCC was estimated to be 6.55-6.72 mills/kWh for proposed DUPIC fuel options, which is a little smaller than that of the once-through FCC by 0.04-0.28 mills/kWh. Considering the uncertainty (0.45-0.51 mills/kWh) of the FCC estimated by the Monte Carlo simulation method, the cost difference between the DUPIC and once-through fuel cycle is negligible. On the other hand, the material balance calculation has shown that the DUPIC fuel cycle can save natural uranium resources by -20% and reduce the spent fuel arising by -65%, compared with the once-through fuel cycle. In conclusion, the DUPIC fuel cycle possesses a strong advantage over the once-through fuel cycle from the viewpoint of the environmental effect.

Compatibility analysis of DUPIC fuel (part5) - DUPIC fuel cycle economics analysis

International Nuclear Information System (INIS)

Ko, Won Il; Choi, Hang Bok; Yang, Myung Seung

2000-08-01

This study examines the economics of the DUPIC fuel cycle using unit costs of fuel cycle components estimated based on conceptual designs. The fuel cycle cost (FCC) was calculated by a deterministic method in which reference values of fuel cycle components are used. The FCC was then analyzed by a Monte Carlo simulation to get the uncertainty of the FCC associated with the unit costs of the fuel cycle components. From the deterministic analysis on the one-batch equilibrium fuel cycle model, the DUPIC FCC was estimated to be 6.55-6.72 mills/kWh for proposed DUPIC fuel options, which is a little smaller than that of the once-through FCC by 0.04-0.28 mills/kWh. Considering the uncertainty (0.45-0.51 mills/kWh) of the FCC estimated by the Monte Carlo simulation method, the cost difference between the DUPIC and once-through fuel cycle is negligible. On the other hand, the material balance calculation has shown that the DUPIC fuel cycle can save natural uranium resources by -20% and reduce the spent fuel arising by -65%, compared with the once-through fuel cycle. In conclusion, the DUPIC fuel cycle possesses a strong advantage over the once-through fuel cycle from the viewpoint of the environmental effect

Detection of feigned mental disorders on the personality assessment inventory: a discriminant analysis.

Science.gov (United States)

Rogers, R; Sewell, K W; Morey, L C; Ustad, K L

1996-12-01

Psychological assessment with multiscale inventories is largely dependent on the honesty and forthrightness of those persons evaluated. We investigated the effectiveness of the Personality Assessment Inventory (PAI) in detecting participants feigning three specific disorders: schizophrenia, major depression, and generalized anxiety disorder. With a simulation design, we tested the PAI validity scales on 166 naive (undergraduates with minimal preparation) and 80 sophisticated (doctoral psychology students with 1 week preparation) participants. We compared their results to persons with the designated disorders: schizophrenia (n = 45), major depression (n = 136), and generalized anxiety disorder (n = 40). Although moderately effective with naive simulators, the validity scales evidenced only modest positive predictive power with their sophisticated counterparts. Therefore, we performed a two-stage discriminant analysis that yielded a moderately high hit rate (> 80%) that was maintained in the cross-validation sample, irrespective of the feigned disorder or the sophistication of the simulators.

Flow cytometric life cycle analysis in cellular radiation biology

International Nuclear Information System (INIS)

Wood, J.C.S.

1982-01-01

Three approaches to flow cytometric histogram analysis were developed: (1) differential histogram analysis, (2) DNA histogram analysis, and (3) multiparameter data analysis. These techniques were applied to an important unresolved problem in radiation biology. The initial responses to irradiation of a mammalian cell which occur during the first two cell cycles following the irradiation are of considerable interest to the radiation biologist. During the first two post-irradiation cell cycles, cells which ultimately will survive repair radiation-induced damage, while some cells begin to express some of the radiation-induced nuclear and chomatin damage. Caffeine- and thymidine-treated, and untreated gamma-irradiated cell populations were studied with respect to the radiation-induced G2 delay, deficient DNA synthesis, and the appearance of cells with abnormal DNA contents. It is hypothesized that the measured deficiency in DNA synthesis observed in the first post-irradiation cell cycle may be a result of daughter cells from abnormal first post-irradiation mitoses

Environmental inventories for future electricity supply systems for Switzerland

Energy Technology Data Exchange (ETDEWEB)

Dones, R; Gantner, U; Hirschberg, S [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Doka, G; Knoepfel, I [Eidgenoessische Technische Hochschule, Zurich (Switzerland)

1996-02-01

This report provides the analysis of environmental inventories for selected electricity supply systems considered as possible options to meet the expected electricity demand in Switzerland in year 2030. Two possible electricity demand level cases were postulated by VSE, both under the basic assumption of economic growth: a high-growth demand case corresponding to a yearly increase of 2% from year 1995 to year 2010 and 1% from year 2010 to year 2030, and a low-growth demand case corresponding to a yearly increase of 1% from year 1995 to year 2010 and 0.5% from year 2010 to year 2030. The base (i.e. secured) supply in year 2030 will be, according to VSE, totally dominated by hydro with rather minor contributions from combined heat-and-power plants, small gas turbines, incinerators and solar photovoltaic plants. Due to decommissioning of the currently operating nuclear power plants and expiration of long-term electricity import contracts there will eventually occur a gap between the postulated electricity demand and the base supply. VSE provided seven options to cover this gap, defined in terms of mixes with different contributions from gas, coal, nuclear and solar chains; in this context a distinction is also made with respect to shares of domestic and imported electricity. The systems considered represent advanced technologies, regarded as either typical or most suitable for the Swiss conditions. System-specific input to the present analysis has been partially generated based on direct contacts with the industry. Life Cycle Analysis (LCA) was used to establish environmental inventories for the systems analysed. The analysis has been performed on three levels:(1) individually for each system considered, (2) comparison of systems, (3) comparison of supply options. Results are also provided for these three levels.

Comparative energy analysis on a new regenerative Brayton cycle

International Nuclear Information System (INIS)

Goodarzi, M.

2016-01-01

Highlights: • New regenerative Brayton cycle has been introduced. • New cycle has higher thermal efficiency and lower exhausted heat per output power. • Regenerator may remain useful in the new cycle even at high pressure ratio. • New regenerative Brayton cycle is suggested for low pressure ratio operations. - Abstract: Gas turbines are frequently used for power generation. Brayton cycle is the basis for gas turbine operation and developing the alternative cycles. Regenerative Brayton cycle is a developed cycle for basic Brayton cycle with higher thermal efficiency at low to moderate pressure ratios. A new regenerative Brayton cycle has been introduced in the present study. Energy analysis has been conducted on ideal cycles to compare them from the first law of thermodynamics viewpoint. Comparative analyses showed that the new regenerative Brayton cycle has higher thermal efficiency than the original one at the same pressure ratio, and also lower heat absorption and exhausted heat per unite output power. Computed results show that new cycle improves thermal efficiency from 12% to 26% relative to the original regenerative Brayton cycle in the range of studied pressure ratios. Contrary to the original regenerative Brayton cycle, regenerator remains useful in the new regenerative Brayton cycle even at higher pressure ratio.

Life cycle analysis of biogas from residues; Livscykelanalys av biogas fraan restprodukter

Energy Technology Data Exchange (ETDEWEB)

Tufvesson, Linda; Lantz, Mikael [Dep. for Miljoe- och Energisystem, Lunds Tekniska Hoegskola, Lund (Sweden)

2012-06-15

The purpose of this study is to carry out life cycle assessments for different biogas systems where biogas is produced from different residues. The investigated residues are distiller's waste, rapeseed cake, whey permeate, concentrated whey permeate, fodder milk, fish residues, bakery residues and glycerol. The environmental impact categories included are climate change, eutrophication, acidification, photochemical ozone creation potential, particles and energy balance. The calculations include emissions from technical systems, especially the energy input in various operations and processes. A general conclusion is that all studied residues are very well suited for production of biogas if there is no demand for them as animal feed today. All biogas systems also reduce the emissions of greenhouse gases compared to petrol and diesel and meet the requirements presented in the EU renewable energy directive (RED). The results of the study also show that the investigated biogas systems are complex and many different parameters affect the result. These parameters are both integrated in the life cycle assessment method, but also in the inventory data used.

Exergy analysis of a combined power and cooling cycle

International Nuclear Information System (INIS)

Fontalvo, Armando; Pinzon, Horacio; Duarte, Jorge; Bula, Antonio; Quiroga, Arturo Gonzalez; Padilla, Ricardo Vasquez

2013-01-01

This paper presents a comprehensive exergy analysis of a combined power and cooling cycle which combines a Rankine and absorption refrigeration cycle by using ammonia–water mixture as working fluid. A thermodynamic model was developed in Matlab ® to find out the effect of pressure ratio, ammonia mass fraction at the absorber and turbine efficiency on the total exergy destruction of the cycle. The contribution of each cycle component on the total exergy destruction was also determined. The results showed that total exergy destruction decreases when pressure ratio increases, and reaches a maximum at x ≈ 0.5, when ammonia mass fraction is varied at absorber. Also, it was found that the absorber, the boiler and the turbine had the major contribution to the total exergy destruction of the cycle, and the increase of the turbine efficiency reduces the total exergy destruction. The effect of rectification cooling source (external and internal) on the cycle output was investigated, and the results showed that internal rectification cooling reduces the total exergy destruction of the cycle. Finally, the effect of the presence or absence of the superheater after the rectification process was determined and it was obtained that the superheated condition reduces the exergy destruction of the cycle at high turbine efficiency values. Highlights: • A parametric exergy analysis of a combined power and cooling cycle is performed. • Two scenarios for rectifier cooling (internal and external) were studied. • Internal cooling source is more exergetic efficient than external cooling source. • The absorber and boiler have the largest total exergy destruction. • Our results show that the superheater reduces the exergy destruction of the cycle

Competitive Analysis of the Online Inventory Problem

DEFF Research Database (Denmark)

Larsen, Kim Skak; Wøhlk, Sanne

2010-01-01

We consider a real-time version of the inventory problem with deterministic demand in which decisions as to when to replenish and how much to buy must be made in an online fashion without knowledge of future prices. We suggest online algorithms for each of four models for the problem and use...

Investigating Psychometric Properties of the Persian Version of Positive Psychotherapy Inventory

Directory of Open Access Journals (Sweden)

Z Ghorbani

2015-08-01

Full Text Available The purpose of the study was to investigate psychometric properties of the Persian version of positive psychotherapy inventory in university students. Research method was descriptive, correlational type. The sample of the study consist of 432 MS and PhD students, 225 female and 207 male, aged between 23 to 45 of state universities of Tehran who were selected through multi-stage random sampling. To study reliability, convergent and structural validity of instrument the sample group completed, positive psychotherapy inventory (Rashid and Oxford Happiness Inventory (Argyle and Hills. To investigating the reliability Cronbach alpha and test- retest method, and for validity of instrument structural validity exploratory factor analysis method and convergent validity were used. Results showed the total internal consistency of positive psychotherapy inventory was 0.80 and subscales internal consistency was between 0.80 to 0.92 respectively. In addition test-retest reliability coefficient was 0.70 for total inventory and between 0.63 to 0.73 for the subscales. Also the correlation coefficients between positive psychotherapy inventory and oxford happiness inventory were 0.73, which indicated a satisfactory convergent validity for positive psychotherapy inventory. Confirmatory factor analysis results showed three factors model of positive psychotherapy inventory in the Iranian sample. These three factors explained 79.99 variance of total inventory.

Nuclide inventories of spent fuels from light water reactors

International Nuclear Information System (INIS)

Okumura, Keisuke; Okamoto, Tsutomu

2012-02-01

Accurate information on nuclide inventories of spent fuels from Light Water Reactors (LWRs) is important for evaluations of criticality, decay heat, radioactivity, toxicity, and so on, in the safety assessments of storage, transportation, reprocessing and waste disposal of the spent fuels. So, a lot of lattice burn-up calculations were carried out for the possible fuel specifications and irradiation conditions in Japanese commercial LWRs by using the latest nuclear data library JENDL-4.0 and a sophisticated lattice burn-up calculation code MOSRA-SRAC. As a result, burn-up changes of nuclide inventories and their possible ranges were clarified for 21 heavy nuclides and 118 fission products, which are important from the viewpoint of impacts to nuclear characteristics and nuclear fuel cycle and environment. (author)

A Global Chance-Constraint for Stochastic Inventory Systems under Service Level Constraints

NARCIS (Netherlands)

Rossi, R.; Tarim, S.A.; Hnich, B.; Prestwich, S.

2008-01-01

We consider a class of production/inventory control problems that has a single product and a single stocking location, for which a stochastic demand with a known non-stationary probability distribution is given. Under the widely-known replenishment cycle policy the problem of computing policy

Impact of ADTT concepts on the management of global plutonium inventories

International Nuclear Information System (INIS)

Davidson, J.W.; Krakowski, R.A.; Arthur, E.D.

1996-01-01

The impact of a number of current and future nuclear systems on global plutonium inventories is assessed under realistic forecasts of nuclear power growth. Advanced systems, such as those employing Accelerator Driven Transmutation Technologies (ADTT) and liquid metal reactors, show significant promise for meeting future plutonium management needs. These analyses also indicate requirements for a higher level of detail in the nuclear fuel cycle model and for development of a metric to more quantitatively assess the proliferation risk of plutonium arising from the civilian fuel cycle

Sensitivity analysis in life cycle assessment

NARCIS (Netherlands)

Groen, E.A.; Heijungs, R.; Bokkers, E.A.M.; Boer, de I.J.M.

2014-01-01

Life cycle assessments require many input parameters and many of these parameters are uncertain; therefore, a sensitivity analysis is an essential part of the final interpretation. The aim of this study is to compare seven sensitivity methods applied to three types of case stud-ies. Two

The environmental impact of organic Rankine cycle for waste heat recovery through life-cycle assessment

International Nuclear Information System (INIS)

Liu, Chao; He, Chao; Gao, Hong; Xie, Hui; Li, Yourong; Wu, Shuangying; Xu, Jinliang

2013-01-01

The LCA (life-cycle assessment) was applied to evaluate EI (the environmental impact) of ORCPW (organic Rankine cycle power-plant for waste-heat-recovery) in this paper. The model of LCA on the ORCPW was established. The life-cycle of ORCPW was divided into construction, operation and decommissioning phases. The inventory of environmental emissions was listed for the ORCPW with 7 different working fluids. The GWP (global warming potential), AP (acidification potential), EP (eutrophication potential), HTP (human toxicity potential), SWP (solid waste potential) and SAP (soot and dust potential) were investigated. Some EIs of ORCPW were compared with the EIs of other power generation modes. The results show that the construction phase of ORCPW contributes mostly to the GWP and EP. GWP is the most serious EI followed by HTP among all the environmental impacts. The average pay back times of greenhouse gas discharged from ORCPW is calculated on the basis of five other power generation modes. For 7 different working fluids, it is 3–5 years for CO 2 , about one year for CH 4 and 3–6 years for NO x . But CO cannot be paid back during the life-cycle of ORCPW according to the average pay back time. - Highlights: • LCA was proposed to evaluate the environmental performance of ORC. • The ORC life cycle environmental emissions inventory was established. • GWP is the most serious environmental impact, followed by HTP. • The ORC with R113 exhibits the lowest environment impact load, followed by Pentane. • The total GWP of ORC could be paid back in 5 years

Risk Analysis of a Two-Level Supply Chain Subject to Misplaced Inventory

Directory of Open Access Journals (Sweden)

Lijing Zhu

2017-06-01

Full Text Available Misplaced inventory is prevalent in retail stores and may lead to the overall poor performance of the supply chain. We explore the impact of misplaced inventory on a two-level supply chain, which consists of a risk-neutral supplier and a risk-averse retailer. The supplier decides the wholesale price to maximize her profit, whereas the retailer decides the order quantity to maximize his utility. Under the Conditional Value-at-Risk (CVaR criterion, we formulate the problem as a Stackelberg game model and obtain the equilibrium solutions in three cases: (i information asymmetry about inventory errors exists; (ii the retailer shares information about inventory errors with the supplier; and (iii in order to reduce misplaced inventory, the supply chain deploys Radio-Frequency Identification (RFID technology. The benefits of information sharing and RFID implementation are explored. A revenue and cost sharing contract is proposed to coordinate the supply chain and to allocate the cost savings from RFID implementation among supply chain participants. Finally, we provide managerial insights for risk-averse decision makers that are considering investing in the RFID technology.

Fuel cycle based safeguards

International Nuclear Information System (INIS)

De Montmollin, J.M.; Higinbotham, W.A.; Gupta, D.

1985-07-01

In NPT safeguards the same model approach and absolute-quantity inspection goals are applied at present to all similar facilities, irrespective of the State's fuel cycle. There is a continuing interest and activity on the part of the IAEA in new NPT safeguards approaches that more directly address a State's nuclear activities as a whole. This fuel cycle based safeguards system is expected to a) provide a statement of findings for the entire State rather than only for individual facilities; b) allocate inspection efforts so as to reflect more realistically the different categories of nuclear materials in the different parts of the fuel cycle and c) provide more timely and better coordinated information on the inputs, outputs and inventories of nuclear materials in a State. (orig./RF) [de

Designing Intelligent Secure Android Application for Effective Chemical Inventory

Science.gov (United States)

Shukran, Mohd Afizi Mohd; Naim Abdullah, Muhammad; Nazri Ismail, Mohd; Maskat, Kamaruzaman; Isa, Mohd Rizal Mohd; Shahfee Ishak, Muhammad; Adib Khairuddin, Muhamad

2017-08-01

Mobile services support various situations in everyday life and with the increasing sophistication of phone functions, the daily life is much more easier and better especially in term of managing tools and apparatus. Since chemical inventory management system has been experiencing a new revolution from antiquated to an automated inventory management system, some additional features should be added in current chemical inventory system. Parallel with the modern technologies, chemical inventory application using smart phone has been developed. Several studies about current related chemical inventory management using smart phone application has been done in this paper in order to obtain an overview on recent studies in smartphone application for chemical inventory system which are needed in schools, universities or other education institutions. This paper also discuss about designing the proposed secure mobile chemical inventory system. The study of this paper can provide forceful review analysis support for the chemical inventory management system related research.

Anomalous dismeter distribution shifts estimated from FIA inventories through time

Science.gov (United States)

Francis A. Roesch; Paul C. Van Deusen

2010-01-01

In the past decade, the United States Department of Agriculture Forest Service’s Forest Inventory and Analysis Program (FIA) has replaced regionally autonomous, periodic, state-wide forest inventories using various probability proportional to tree size sampling designs with a nationally consistent annual forest inventory design utilizing systematically spaced clusters...

Dynamic analysis of the CTAR (constant temperature adsorption refrigeration) cycle

International Nuclear Information System (INIS)

Hassan, H.Z.; Mohamad, A.A.; Al-Ansary, H.A.; Alyousef, Y.M.

2014-01-01

The basic SAR (solar-driven adsorption refrigeration) machine is an intermittent cold production system. Recently, the CO-SAR (continuous operation solar-powered adsorption refrigeration) system is developed. The CO-SAR machine is based on the theoretical CTAR (constant temperature adsorption refrigeration) cycle in which the adsorption process takes place at a constant temperature that equals the ambient temperature. Practically, there should be a temperature gradient between the adsorption bed and the surrounding atmosphere to provide a driving potential for heat transfer. In the present study, the dynamic analysis of the CTAR cycle is developed. This analysis provides a comparison between the theoretical and the dynamic operation of the CTAR cycle. The developed dynamic model is based on the D-A adsorption equilibrium equation and the energy and mass balances in the adsorption reactor. Results obtained from the present work demonstrate that, the idealization of the constant temperature adsorption process in the theoretical CTAR cycle is not far from the real situation and can be approached. Furthermore, enhancing the heat transfer between the adsorption bed and the ambient during the bed pre-cooling process helps accelerating the heat rejection process from the adsorption reactor and therefore approaching the isothermal process. - Highlights: • The dynamic analysis of the CTAR (constant temperature adsorption refrigeration) cycle is developed. • The CTAR theoretical and dynamic cycles are compared. • The dynamic cycle approaches the ideal one by enhancing the bed precooling

Nitrogen Cycle Evaluation (NiCE) Chip for the Simultaneous Analysis of Multiple N-Cycle Associated Genes.

Science.gov (United States)

Oshiki, Mamoru; Segawa, Takahiro; Ishii, Satoshi

2018-02-02

Various microorganisms play key roles in the Nitrogen (N) cycle. Quantitative PCR (qPCR) and PCR-amplicon sequencing of the N cycle functional genes allow us to analyze the abundance and diversity of microbes responsible in the N transforming reactions in various environmental samples. However, analysis of multiple target genes can be cumbersome and expensive. PCR-independent analysis, such as metagenomics and metatranscriptomics, is useful but expensive especially when we analyze multiple samples and try to detect N cycle functional genes present at relatively low abundance. Here, we present the application of microfluidic qPCR chip technology to simultaneously quantify and prepare amplicon sequence libraries for multiple N cycle functional genes as well as taxon-specific 16S rRNA gene markers for many samples. This approach, named as N cycle evaluation (NiCE) chip, was evaluated by using DNA from pure and artificially mixed bacterial cultures and by comparing the results with those obtained by conventional qPCR and amplicon sequencing methods. Quantitative results obtained by the NiCE chip were comparable to those obtained by conventional qPCR. In addition, the NiCE chip was successfully applied to examine abundance and diversity of N cycle functional genes in wastewater samples. Although non-specific amplification was detected on the NiCE chip, this could be overcome by optimizing the primer sequences in the future. As the NiCE chip can provide high-throughput format to quantify and prepare sequence libraries for multiple N cycle functional genes, this tool should advance our ability to explore N cycling in various samples. Importance. We report a novel approach, namely Nitrogen Cycle Evaluation (NiCE) chip by using microfluidic qPCR chip technology. By sequencing the amplicons recovered from the NiCE chip, we can assess diversities of the N cycle functional genes. The NiCE chip technology is applicable to analyze the temporal dynamics of the N cycle gene

Introducing buffer inventories in the RBD analysis of process production systems

International Nuclear Information System (INIS)

Macchi, Marco; Kristjanpoller, Fredy; Garetti, Marco; Arata, Adolfo; Fumagalli, Luca

2012-01-01

The throughput analysis is an important issue for the design and operations management of process production lines. The throughput of a line depends on the availability and nominal throughput of its machines. Further on, it is influenced by the accumulation process of production material stocked into buffers along the line; hence, the buffer inventory level is also a relevant variable that has to be considered when assessing the throughput of the line. The present paper is particularly concerned with using such an assessment for supporting maintenance decisions. The buffer inventory level should provide the proper isolation time before the buffer becomes empty, so that, during this time, a maintenance intervention can be carried on at a failed machine upward, without causing a propagation of the effect of the failure in the machines downward (the so called ‘material starvation’). Alike, it should guarantee the proper isolation time before reaching the complete utilisation of the buffer capacity, so that also during this time a maintenance intervention is possible at a failed machine downward without causing a propagation of the effect of the failure in the machines upward (the so called ‘blocking of production’). This strategy is particularly interesting in the process industry where the capital cost of equipment is high and the holding cost of material is low. Hence, the isolation times before reaching ‘material starvation’ or ‘blocking of production’ have to be properly studied in order to make an accurate analysis of their effect on the throughput of the line. The present paper provides a model to this end, derived by extending the well known Reliability Block Diagram (RBD) method, currently used in the normal duties of a maintenance engineer. The usual RBD availability analysis is integrated by a state space analysis through which isolation times can be analysed. Besides, an empirical study – the case of a production line taken out from the

Design of inventory pools in spare part support operation systems

Science.gov (United States)

Mo, Daniel Y.; Tseng, Mitchell M.; Cheung, Raymond K.

2014-06-01

The objective of a spare part support operation is to fulfill the part request order with different service contracts in the agreed response time. With this objective to achieve different service targets for multiple service contracts and the considerations of inventory investment, it is not only important to determine the inventory policy but also to design the structure of inventory pools and the order fulfilment strategies. In this research, we focused on two types of inventory pools: multiple inventory pool (MIP) and consolidated inventory pool (CIP). The idea of MIP is to maintain separated inventory pools based on the types of service contract, while CIP solely maintains a single inventory pool regardless of service contract. Our research aims to design the inventory pool analytically and propose reserve strategies to manage the order fulfilment risks in CIP. Mathematical models and simulation experiments would be applied for analysis and evaluation.

Reduction of worldwide plutonium inventories using conventional reactors and advanced fuels: A systems study

International Nuclear Information System (INIS)

Krakowski, R.A.; Bathke, C.G.; Chodak, P. III

1997-01-01

The potential for reducing plutonium inventories in the civilian nuclear fuel cycle through recycle in LWRs of a variety of mixed-oxide forms is examined by means of a cost-based plutonium-flow systems model that includes an approximate measure of proliferation risk. The impact of plutonium recycle in a number of forms is examined, including the introduction of nonfertile fuels into conventional (LWR) reactors to reduce net plutonium generation, to increase plutonium burnup, and to reduce exo-reactor plutonium inventories

Hybrid life-cycle environmental and cost inventory of sewage sludge treatment and end-use scenarios: a case study from China.

Science.gov (United States)

Murray, Ashley; Horvath, Arpad; Nelson, Kara L

2008-05-01

Sewage sludge management poses environmental, economic, and political challenges for wastewater treatment plants and municipalities around the globe. To facilitate more informed and sustainable decision making, this study used life-cycle inventory (LCI) to expand upon previous process-based LCIs of sewage sludge treatmenttechnologies. Additionally, the study evaluated an array of productive end-use options for treated sewage sludge, such as fertilizer and as an input into construction materials, to determine how the sustainability of traditional manufacturing processes changes with sludge as a replacement for other raw inputs. The inclusion of the life-cycle of necessary inputs (such as lime) used in sludge treatment significantly impacts the sustainability profiles of different treatment and end-use schemes. Overall, anaerobic digestion is generally the optimal treatment technology whereas incineration, particularly if coal-fired, is the most environmentally and economically costly. With respect to sludge end use, offsets are greatest for the use of sludge as fertilizer, but all of the productive uses of sludge can improve the sustainability of conventional manufacturing practices. The results are intended to help inform and guide decisions about sludge handling for existing wastewater treatment plants and those that are still in the planning phase in cities around the world. Although additional factors must be considered when selecting a sludge treatment and end-use scheme, this study highlights how a systems approach to planning can contribute significantly to improving overall environmental sustainability.

Towards a comprehensive greenhouse gas emissions inventory for biosolids.

Science.gov (United States)

Alvarez-Gaitan, J P; Short, Michael D; Lundie, Sven; Stuetz, Richard

2016-06-01

Effective handling and treatment of the solids fraction from advanced wastewater treatment operations carries a substantial burden for water utilities relative to the total economic and environmental impacts from modern day wastewater treatment. While good process-level data for a range of wastewater treatment operations are becoming more readily available, there remains a dearth of high quality operational data for solids line processes in particular. This study seeks to address this data gap by presenting a suite of high quality, process-level life cycle inventory data covering a range of solids line wastewater treatment processes, extending from primary treatment through to biosolids reuse in agriculture. Within the study, the impacts of secondary treatment technology and key parameters such as sludge retention time, activated sludge age and primary-to-waste activated sludge ratio (PS:WAS) on the life cycle inventory data of solids processing trains for five model wastewater treatment plant configurations are presented. BioWin(®) models are calibrated with real operational plant data and estimated electricity consumption values were reconciled against overall plant energy consumption. The concept of "representative crop" is also introduced in order to reduce the uncertainty associated with nitrous oxide emissions and soil carbon sequestration offsets under biosolids land application scenarios. Results indicate that both the treatment plant biogas electricity offset and the soil carbon sequestration offset from land-applied biosolids, represent the main greenhouse gas mitigation opportunities. In contrast, fertiliser offsets are of relatively minor importance in terms of the overall life cycle emissions impacts. Results also show that fugitive methane emissions at the plant, as well as nitrous oxide emissions both at the plant and following agricultural application of biosolids, are significant contributors to the overall greenhouse gas balance and combined are

Confirmatory Factor Analysis of the Universiti Sains Malaysia Emotional Quotient Inventory Among Medical Students in Malaysia

Directory of Open Access Journals (Sweden)

Wan Nor Arifin

2016-05-01

Full Text Available The Universiti Sains Malaysia Emotional Quotient Inventory (USMEQ-i is a Malay-language emotional intelligence (EI inventory that was based on a mixed-model approach of EI. It was specifically developed and validated for use among medical course applicants. However, evidence to support its use among medical students is inadequate. This study aims to provide further construct validity evidence for the USMEQ-i among medical students through confirmatory factor analysis (CFA. A cross-sectional study was carried out on a sample of 479 medical students in Universiti Sains Malaysia (USM. After a preliminary analysis, data from only 317 respondents were found suitable for inclusion in CFA. CFA was performed using the maximum likelihood estimation method with bootstrapping due to the nonnormality of items at the multivariate level. The results of the analysis support the two-factor model of the EI component and the one-factor model of the faking component. However, the USMEQ-i should be administered with caution until further cross-validation studies are conducted among students in other medical schools in Malaysia.

Life cycle impacts of manufacturing redwood decking in Northern California

Science.gov (United States)

Richard D. Bergman; Elaine Oneil; Ivan L. Eastin; Han-Sup Han

2014-01-01

Awareness of the environmental footprint of building construction and use has led to increasing interest in green building. Defining a green building is an evolving process with life cycle inventory and life cycle impact assessment (LCIA) emerging as key tools in that evolution and definition process. This study used LCIA to determine the environmental footprint...

Thermodynamic Analysis of Supplementary-Fired Gas Turbine Cycles

DEFF Research Database (Denmark)

Elmegaard, Brian; Henriksen, Ulrik Birk; Qvale, Einar Bjørn

2003-01-01

to result in a high marginal efficiency. The paper shows that depending on the application, this is not always the case. The interest in this cycle arises from a recent demonstration of the feasibility of a two-stage gasification process through construction of several plants. The gas from this process...... could be divided into two streams, one for primary and one for supplementary firing. A preliminary analysis of the ideal, recuperated Brayton cycle shows that for this cycle any supplementary firing will have a marginal efficiency of unity per extra unit of fuel. The same result is obtained...

Activity based costing model for inventory valuation

Directory of Open Access Journals (Sweden)

Vineet Chouhan

2017-03-01

Full Text Available Activity-Based-Model (ABC is used for the purpose of significant improvement for overhead accounting systems by providing the best information required for managerial decision. This pa-per discusses implacability of ABC technique on inventory valuation as a management account-ing innovation. In order to prove the applicability of ABC for inventory control a material driven medium-sized and privately owned company from engineering (iron and steel industry is select-ed and by analysis of its production process and its material dependency and use of indirect in-ventory, an ABC model is explored for better inventory control. The case revealed that the ne-cessity of ABC in the area of inventory control is significant. The company is not only able to increase its quality of decision but also it can significantly analyze its cost of direct material cost, valuation of direct material and use its implications for better decision making.

Exergy analysis, parametric analysis and optimization for a novel combined power and ejector refrigeration cycle

International Nuclear Information System (INIS)

Dai Yiping; Wang Jiangfeng; Gao Lin

2009-01-01

A new combined power and refrigeration cycle is proposed, which combines the Rankine cycle and the ejector refrigeration cycle. This combined cycle produces both power output and refrigeration output simultaneously. It can be driven by the flue gas of gas turbine or engine, solar energy, geothermal energy and industrial waste heats. An exergy analysis is performed to guide the thermodynamic improvement for this cycle. And a parametric analysis is conducted to evaluate the effects of the key thermodynamic parameters on the performance of the combined cycle. In addition, a parameter optimization is achieved by means of genetic algorithm to reach the maximum exergy efficiency. The results show that the biggest exergy loss due to the irreversibility occurs in heat addition processes, and the ejector causes the next largest exergy loss. It is also shown that the turbine inlet pressure, the turbine back pressure, the condenser temperature and the evaporator temperature have significant effects on the turbine power output, refrigeration output and exergy efficiency of the combined cycle. The optimized exergy efficiency is 27.10% under the given condition.

Integrative Application of Life Cycle Assessment and Risk Assessment to Environmental Impacts of Anthropogenic Pollutants at a Watershed Scale.

Science.gov (United States)

Lin, Xiaodan; Yu, Shen; Ma, Hwongwen

2018-01-01

Intense human activities have led to increasing deterioration of the watershed environment via pollutant discharge, which threatens human health and ecosystem function. To meet a need of comprehensive environmental impact/risk assessment for sustainable watershed development, a biogeochemical process-based life cycle assessment and risk assessment (RA) integration for pollutants aided by geographic information system is proposed in this study. The integration is to frame a conceptual protocol of "watershed life cycle assessment (WLCA) for pollutants". The proposed WLCA protocol consists of (1) geographic and environmental characterization mapping; (2) life cycle inventory analysis; (3) integration of life-cycle impact assessment (LCIA) with RA via characterization factor of pollutant of interest; and (4) result analysis and interpretation. The WLCA protocol can visualize results of LCIA and RA spatially for the pollutants of interest, which might be useful for decision or policy makers for mitigating impacts of watershed development.

The use of remote sensing for updating extensive forest inventories

Science.gov (United States)

John F. Kelly

1990-01-01

The Forest Inventory and Analysis unit of the USDA Forest Service Southern Forest Experiment Station (SO-FIA) has the research task of devising an inventory updating system that can be used to provide reliable estimates of forest area, volume, growth, and removals at the State level. These updated inventories must be accomplished within current budgetary restraints....

Inventory decision in a closed-loop supply chain with inspection, sorting, and waste disposal

Science.gov (United States)

Dwicahyani, A. R.; Jauhari, W. A.; Kurdhi, N. A.

2016-02-01

The study of returned item inventory management in a closed-loop supply chain system has become an important issue in recent years. So far, investigations about inventory decision making in a closed-loop supply chain system have been confined to traditional forward and reverse oriented material flow supply chain. In this study, we propose an integrated inventory model consisting a supplier, a manufacturer, and a retailer where the manufacturer inspects all of the returned items collected from the customers and classifies them as recoverable or waste. Returned items that recovered through the remanufacturing process and the newly manufactured products are then used to meet the demand of the retailer. However, some recovered items which are not comparable to the ones in quality, classified as refurbished items, are sold to a secondary market at a reduced price. This study also suggests that the flow of returned items is controlled by a decision variable, namely an acceptance quality level of recoverable item in the system. We apply multiple remanufacturing cycle and multiple production cycle policy to the proposed model and give the corresponding iterative procedure to determine the optimal solutions. Further, numerical examples are presented for illustrative purpose.

A Thermodynamic Analysis of Two Competing Mid-Sized Oxyfuel Combustion Combined Cycles

Directory of Open Access Journals (Sweden)

Egill Thorbergsson

2016-01-01

Full Text Available A comparative analysis of two mid-sized oxyfuel combustion combined cycles is performed. The two cycles are the semiclosed oxyfuel combustion combined cycle (SCOC-CC and the Graz cycle. In addition, a reference cycle was established as the basis for the analysis of the oxyfuel combustion cycles. A parametric study was conducted where the pressure ratio and the turbine entry temperature were varied. The layout and the design of the SCOC-CC are considerably simpler than the Graz cycle while it achieves the same net efficiency as the Graz cycle. The fact that the efficiencies for the two cycles are close to identical differs from previously reported work. Earlier studies have reported around a 3% points advantage in efficiency for the Graz cycle, which is attributed to the use of a second bottoming cycle. This additional feature is omitted to make the two cycles more comparable in terms of complexity. The Graz cycle has substantially lower pressure ratio at the optimum efficiency and has much higher power density for the gas turbine than both the reference cycle and the SCOC-CC.

The thorium fuel cycle in water-moderated reactor systems

International Nuclear Information System (INIS)

Critoph, E.

1977-01-01

Current interest in the thorium cycle, as an alternative to the uranium cycle, for water-moderated reactors is based on two attractive aspects of its use - the extension of uranium resources, and the related lower sensitivity of energy costs to uranium price. While most of the scientific basis required is already available, some engineering demonstrations are needed to provide better economic data for rational decisions. Thorium and uranium cycles are compared with regard to reactor characteristics and technology, fuel-cycle technology, economic parameters, fuel-cycle costs, and system characteristics. There appear to be no major feasibility problems associated with the use of thorium, although development is required in the areas of fuel testing and fuel management. The use of thorium cycles implies recycling the fuel, and the major uncertainties are in the associated costs. Experience in the design and operation of fuel reprocessing and active-fabrication facilities is required to estimate costs to the accuracy needed for adequately defining the range of conditions economically favourable to thorium cycles. In heavy-water reactors (HWRs) thorium cycles having uranium requirements at equilibrium ranging from zero to a quarter of those for the natural-uranium once-through cycle appear feasible. An ''inventory'' of uranium of between 1 and 2Mg/MW(e) is required for the transition to equilibrium. The cycles with the lowest uranium requirements compete with the others only at high uranium prices. Using thorium in light-water reactors, uranium requirements can be reduced by a factor of between two and three from the once-through uranium cycle. The light-water breeder reactor, promising zero uranium requirements at equilibrium, is being developed. Larger uranium inventories are required than for the HWRs. The lead time, from a decision to use thorium to significant impact on uranium utilization (compared to uranium cycle, recycling plutonium), is some two decades

Development of the HD-Teen Inventory.

Science.gov (United States)

Driessnack, Martha; Williams, Janet K; Barnette, J Jackson; Sparbel, Kathleen J; Paulsen, Jane S

2012-05-01

Adolescents, who have a parent with Huntington Disease (HD), not only are at genetic risk for HD but also are witness to its onset and devastating clinical progression as their parent declines. To date, no mechanism has been developed to direct health care providers to the atypical adolescent experiences of these teens. The purpose of this report is to describe the process of developing the HD-Teen Inventory clinical assessment tool. Forty-eight teens and young adults from 19 U.S. states participated in the evaluation of the HD-Teen Inventory tool. Following item analysis, the number of items was reduced and item frequency and reaction scales were combined, based on the strong correlation (r = .94). The resultant tool contains 15 inventory and 2 open-ended response items. The HD-Teen Inventory emerged as a more compact and efficient tool for identifying the most salient concerns of at-risk teens in HD families in research and/or clinical practice.

sensitivity analysis on flexible road pavement life cycle cost model

African Journals Online (AJOL)

user

of sensitivity analysis on a developed flexible pavement life cycle cost model using varying discount rate. The study .... organizations and specific projects needs based. Life-cycle ... developed and completed urban road infrastructure corridor ...

Energy and entropy analysis of closed adiabatic expansion based trilateral cycles

International Nuclear Information System (INIS)

Garcia, Ramon Ferreiro; Carril, Jose Carbia; Gomez, Javier Romero; Gomez, Manuel Romero

2016-01-01

Highlights: • The adiabatic expansion based TC surpass Carnot factor at low temperatures. • The fact of surpassing Carnot factor doesn’t violate the 2nd law. • An entropy analysis is applied to verify the fulfilment of the second law. • Correction of the exergy transfer associated with heat transferred to a cycle. - Abstract: A vast amount of heat energy is available at low cost within the range of medium and low temperatures. Existing thermal cycles cannot make efficient use of such available low grade heat because they are mainly based on conventional organic Rankine cycles which are limited by Carnot constraints. However, recent developments related to the performance of thermal cycles composed of closed processes have led to the exceeding of the Carnot factor. Consequently, once the viability of closed process based thermal cycles that surpass the Carnot factor operating at low and medium temperatures is globally accepted, research work will aim at looking into the consequences that lead from surpassing the Carnot factor while fulfilling the 2nd law, its impact on the 2nd law efficiency definition as well as the impact on the exergy transfer from thermal power sources to any heat consumer, including thermal cycles. The methodology used to meet the proposed objectives involves the analysis of energy and entropy on trilateral closed process based thermal cycles. Thus, such energy and entropy analysis is carried out upon non-condensing mode trilateral thermal cycles (TCs) characterised by the conversion of low grade heat into mechanical work undergoing closed adiabatic path functions: isochoric heat absorption, adiabatic heat to mechanical work conversion and isobaric heat rejection. Firstly, cycle energy analysis is performed to determine the range of some relevant cycle parameters, such as the operating temperatures and their associated pressures, entropies, internal energies and specific volumes. In this way, the ranges of temperatures within which

Forest inventory in Myanmar

Energy Technology Data Exchange (ETDEWEB)

Bo, Sit [Forest Resource Div., Forest Department (Myanmar)

1993-10-01

Forest inventory in Myanmar started in 1850s. Up till 1975, Myanmar Forest Department conducted forest inventories covering approximately one forest division every year. The National Forest Survey and Inventory Project funded by UNDP and assisted by FAO commenced in 1981 and the National Forest Management and Inventory project followed in 1986. Up till end March 1993, pre-investment inventory has covered 26.7 million acres, reconnaissance inventory 5.4 million acres and management inventory has carried out in 12 townships

Forest inventory in Myanmar

International Nuclear Information System (INIS)

Sit Bo

1993-01-01

Forest inventory in Myanmar started in 1850s. Up till 1975, Myanmar Forest Department conducted forest inventories covering approximately one forest division every year. The National Forest Survey and Inventory Project funded by UNDP and assisted by FAO commenced in 1981 and the National Forest Management and Inventory project followed in 1986. Up till end March 1993, pre-investment inventory has covered 26.7 million acres, reconnaissance inventory 5.4 million acres and management inventory has carried out in 12 townships

Second Law Of Thermodynamics Analysis Of Triple Cycle Power Plant

Directory of Open Access Journals (Sweden)

Matheus M. Dwinanto

2012-11-01

Full Text Available Triple cycle power plant with methane as a fuel has been analyzed on the basis of second law of thermodynamics.In this model, ideal Brayton cycle is selected as a topping cycle as it gives higher efficiency at lower pressure ratio comparedintercooler and reheat cycle. In trilple cycle the bottoming cycles are steam Rankine and organic Rankine cycle. Ammoniahas suitable working properties like critical temperature, boiling temperature, etc. Steam cycle consists of a deaerator andreheater. The bottoming ammonia cycle is a ideal Rankine cycle. Single pressure heat recovery steam and ammoniagenerators are selected for simplification of the analysis. The effects of pressure ratio and maximum temperature which aretaken as important parameters regarding the triple cycle are discussed on performance and exergetic losses. On the otherhand, the efficiency of the triple cycle can be raised, especially in the application of recovering low enthalpy content wasteheat. Therefore, by properly combining with a steam Rankine cycle, the ammonia Rankine cycle is expected to efficientlyutilize residual yet available energy to an optimal extent. The arrangement of multiple cycles is compared with combinedcycle having the same sink conditions. The parallel type of arrangement of bottoming cycle is selected due to increasedperformance.

Development and application of dynamic hybrid multi-region inventory analysis for macro-level environmental policy analysis: a case study on climate policy in Taiwan.

Science.gov (United States)

Chao, Chia-Wei; Heijungs, Reinout; Ma, Hwong-wen

2013-03-19

We develop a novel inventory method called Dynamic Hybrid Multi-Region Inventory analysis (DHMRI), which integrates the EEMRIOA and Integrated Hybrid LCA and applies time-dependent environmental intervention information for inventory analysis. Consequently, DHMRI is able to quantify the change in the environmental footprint caused by a specific policy while taking structural changes and technological dynamics into consideration. DHMRI is applied to assess the change in the total CO2 emissions associated with the total final demand caused by the climate policy in Taiwan to demonstrate the practicality of this novel method. The evaluation reveals that the implementation of mitigation measures included in the existing climate policy, such as an enhancement in energy efficiency, promotion of renewable energy, and limitation of the growth of energy-intensive industries, will lead to a 28% increase in the total CO2 emissions and that the main driver is the export-oriented electronics industry. Moreover, a major increase in the total emissions is predicted to occur in Southeast Asia and China. The observations from the case study reveal that DHMRI is capable of overcoming the limitations of existing assessment tools at macro-level evaluation of environmental policies.

Rankine cycle waste heat recovery system

Science.gov (United States)

Ernst, Timothy C.; Nelson, Christopher R.

2014-08-12

This disclosure relates to a waste heat recovery (WHR) system and to a system and method for regulation of a fluid inventory in a condenser and a receiver of a Rankine cycle WHR system. Such regulation includes the ability to regulate the pressure in a WHR system to control cavitation and energy conversion.

Comparative performance analysis of combined-cycle pulse detonation turbofan engines (PDTEs

Directory of Open Access Journals (Sweden)

Sudip Bhattrai

2013-09-01

Full Text Available Combined-cycle pulse detonation engines are promising contenders for hypersonic propulsion systems. In the present study, design and propulsive performance analysis of combined-cycle pulse detonation turbofan engines (PDTEs is presented. Analysis is done with respect to Mach number at two consecutive modes of operation: (1 Combined-cycle PDTE using a pulse detonation afterburner mode (PDA-mode and (2 combined-cycle PDTE in pulse detonation ramjet engine mode (PDRE-mode. The performance of combined-cycle PDTEs is compared with baseline afterburning turbofan and ramjet engines. The comparison of afterburning modes is done for Mach numbers from 0 to 3 at 15.24 km altitude conditions, while that of pulse detonation ramjet engine (PDRE is done for Mach 1.5 to Mach 6 at 18.3 km altitude conditions. The analysis shows that the propulsive performance of a turbine engine can be greatly improved by replacing the conventional afterburner with a pulse detonation afterburner (PDA. The PDRE also outperforms its ramjet counterpart at all flight conditions considered herein. The gains obtained are outstanding for both the combined-cycle PDTE modes compared to baseline turbofan and ramjet engines.

Environmental impacts of lighting technologies - Life cycle assessment and sensitivity analysis

International Nuclear Information System (INIS)

Welz, Tobias; Hischier, Roland; Hilty, Lorenz M.

2011-01-01

With two regulations, 244/2009 and 245/2009, the European Commission recently put into practice the EuP Directive in the area of lighting devices, aiming to improve energy efficiency in the domestic lighting sector. This article presents a comprehensive life cycle assessment comparison of four different lighting technologies: the tungsten lamp, the halogen lamp, the conventional fluorescent lamp and the compact fluorescent lamp. Taking advantage of the most up-to-date life cycle inventory database available (ecoinvent data version 2.01), all life cycle phases were assessed and the sensitivity of the results for varying assumptions analysed: different qualities of compact fluorescent lamps (production phase), different electricity mixes (use phase), and end-of-life scenarios for WEEE recycling versus municipal solid waste incineration (disposal phase). A functional unit of 'one hour of lighting' was defined and the environmental burdens for the whole life cycle for all four lamp types were calculated, showing a clearly lower impact for the two gas-discharge lamps, i.e. the fluorescent and the compact fluorescent lamp. Differences in the product quality of the compact fluorescent lamps reveal to have only a very small effect on the overall environmental performance of this lamp type; a decline of the actual life time of this lamp type doesn't result in a change of the rank order of the results of the here examined four lamp types. It was also shown that the environmental break-even point of the gas-discharge lamps is reached long before the end of their expected life-span. All in all, it can be concluded that a change from today's tungsten lamp technology to a low-energy-consuming technology such as the compact fluorescent lamp results in a substantial environmental benefit.

Prediction of solar cycle 24 using fourier series analysis

International Nuclear Information System (INIS)

Khalid, M.; Sultana, M.; Zaidi, F.

2014-01-01

Predicting the behavior of solar activity has become very significant. It is due to its influence on Earth and the surrounding environment. Apt predictions of the amplitude and timing of the next solar cycle will aid in the estimation of the several results of Space Weather. In the past, many prediction procedures have been used and have been successful to various degrees in the field of solar activity forecast. In this study, Solar cycle 24 is forecasted by the Fourier series method. Comparative analysis has been made by auto regressive integrated moving averages method. From sources, January 2008 was the minimum preceding solar cycle 24, the amplitude and shape of solar cycle 24 is approximate on monthly number of sunspots. This forecast framework approximates a mean solar cycle 24, with the maximum appearing during May 2014 (+- 8 months), with most sunspot of 98 +- 10. Solar cycle 24 will be ending in June 2020 (+- 7 months). The difference between two consecutive peak values of solar cycles (i.e. solar cycle 23 and 24 ) is 165 months(+- 6 months). (author)

Comparative analysis of thermodynamic performance and optimization of organic flash cycle (OFC) and organic Rankine cycle (ORC)

International Nuclear Information System (INIS)

Lee, Ho Yong; Park, Sang Hee; Kim, Kyoung Hoon

2016-01-01

A comparative thermodynamic performance and optimization analysis of basic organic flash cycle (OFCB), organic flash cycle with two-phase expander (OFCT), and organic Rankine cycle (ORC) activated by low-temperature sensible energy is carried out in the subcritical pressure regions. The three substances of R245fa, R123, and o-xylene are considered as the working fluids. Effects of cycle type, working fluid, and evaporation and source temperatures are systemically investigated on the system performance such as net power production, thermal and exergy efficiencies, and exergy destruction ratios at each component of the systems. Results show that the cycle type or working fluid which shows optimum performance depends on the source temperature, and organic flash cycle shows a potential for efficient recovery of low grade energy source.

Defining the student burnout construct: a structural analysis from three burnout inventories.

Science.gov (United States)

Maroco, João; Campos, Juliana Alvares Duarte Bonini

2012-12-01

College student burnout has been assessed mainly with the Maslach burnout inventory (MBI). However, the construct's definition and measurement with MBI has drawn several criticisms and new inventories have been suggested for the evaluation of the syndrome. A redefinition of the construct of student burnout is proposed by means of a structural equation model, reflecting burnout as a second order factor defined by factors from the MBI-student survey (MBI-SS); the Copenhagen burnout inventory-student survey (CBI-SS) and the Oldenburg burnout inventory-student survey (OLBI-SS). Standardized regression weights from Burnout to Exhaustion and Cynicism from the MBI-SS scale, personal burnout and studies related burnout from the CBI, and exhaustion and disengagement from OLBI, show that these factors are strong manifestations of students' burnout. For college students, the burnout construct is best defined by two dimensions described as "physical and psychological exhaustion" and "cynicism and disengagement".

Inventory Model with Partial Backordering When Backordered Customers Delay Purchase after Stockout-Restoration

Directory of Open Access Journals (Sweden)

Ren-Qian Zhang

2016-01-01

Full Text Available Many inventory models with partial backordering assume that the backordered demand must be filled instantly after stockout restoration. In practice, however, the backordered customers may successively revisit the store because of the purchase delay behavior, producing a limited backorder demand rate and resulting in an extra inventory holding cost. Hence, in this paper we formulate the inventory model with partial backordering considering the purchase delay of the backordered customers and assuming that the backorder demand rate is proportional to the remaining backordered demand. Particularly, we model the problem by introducing a new inventory cost component of holding the backordered items, which has not been considered in the existing models. We propose an algorithm with a two-layer structure based on Lipschitz Optimization (LO to minimize the total inventory cost. Numerical experiments show that the proposed algorithm outperforms two benchmarks in both optimality and efficiency. We also observe that the earlier the backordered customer revisits the store, the smaller the inventory cost and the fill rate are, but the longer the order cycle is. In addition, if the backordered customers revisit the store without too much delay, the basic EOQ with partial backordering approximates our model very well.

Interactive Inventory Monitoring

Science.gov (United States)

Garud, Sumedha

2013-01-01

Method and system for monitoring present location and/or present status of a target inventory item, where the inventory items are located on one or more inventory shelves or other inventory receptacles that communicate with an inventory base station through use of responders such as RFIDs. A user operates a hand held interrogation and display (lAD) module that communicates with, or is part of the base station to provide an initial inquiry. lnformation on location(s) of the larget invenlory item is also indicated visibly and/or audibly on the receptacle(s) for the user. Status information includes an assessment of operation readiness and a time, if known, that the specified inventory item or class was last removed or examined or modified. Presentation of a user access level may be required for access to the target inventgory item. Another embodiment provides inventory informatin for a stack as a sight-impaired or hearing-impaired person adjacent to that stack.

Inventory Management Strategies For Productivity Improvement In Equipment Manufacturing Firms

Directory of Open Access Journals (Sweden)

T.T Amachree

2017-08-01

Full Text Available This study examined and developed Inventory Management Strategies IMS which could be creatively employed for Productivity Improvement in Equipment Firms PIEMF Equipment manufacturing projects suffer from declining productivity and inability to effectively satisfy customized order batch quantity within schedules budgeted cost and quality specifications due to lack of robust and well defined IMS as well as none code classification of vast number of inventory item. Survey and expost-facto research designs were adopted on the four identified IMS in three EMF. The method used for primary data collection and measurement on four IMS and inventory management parameters was questionnaire modelled into likert five point scale from the target respondents being experts in the subject matter. The secondary data was obtained from the computerised inventory status file of the three equipment manufacturing firms. The methods of primary data analysis and test of research used were Pearsons product moment correlation coefficient and oneway. Analysis of variance ANOVA computer software via Statistical Program for Social Science SPSS version 17 ABC analysis and classification of materials was used for code categorization of secondary data also with the aid of Microsoft excel. The results of the analyses highlighted and isolated A class of inventory items which are 137 out of 543 for Siemens Nig. Ltd 154 out of 551 for Dresser-Rand Nig. Ltd and 162 of 551 for Nigerian Engineering Works Ltd. The results of Pearson product moment correlation analysis and test of research hypotheses indicate that Materials Requirements Planning MRP followed by Supply Chain Management SCM are the most significant IMS as they correlate strongly with PIEMF. The study recommends IMS adoption by code classification of materials in which MRP or SCM could be deployed for management of A class of inventories while classical IMS could be used for management B and C classes of inventory items.

Transmutation and inventory analysis in an ATW molten salt system

Energy Technology Data Exchange (ETDEWEB)

Sisolak, J.E.; Truebenbach, M.T.; Henderson, D.L. [Univ. of Wisconsin, Madison, WI (United States)

1995-10-01

As an extension of earlier work to determine the equilibrium state of an ATW molten salt, power producing, reactor/transmuter, the WAIT code provides a time dependent view of material inventories and reactor parameters. By considering several cases, the authors infer that devices of this type do not reach equilibrium for dozens of years, and that equilibrium design calculations are inapplicable over most of the reactor life. Fissile inventory and k{sub eff} both vary by factors of 1.5 or more between reactor startup and ultimate convergence to equilibrium.

Nuclear Fuel Cycle Analysis and Simulation Tool (FAST)

Energy Technology Data Exchange (ETDEWEB)

Ko, Won Il; Kwon, Eun Ha; Kim, Ho Dong

2005-06-15

This paper describes the Nuclear Fuel Cycle Analysis and Simulation Tool (FAST) which has been developed by the Korea Atomic Energy Research Institute (KAERI). Categorizing various mix of nuclear reactors and fuel cycles into 11 scenario groups, the FAST calculates all the required quantities for each nuclear fuel cycle component, such as mining, conversion, enrichment and fuel fabrication for each scenario. A major advantage of the FAST is that the code employs a MS Excel spread sheet with the Visual Basic Application, allowing users to manipulate it with ease. The speed of the calculation is also quick enough to make comparisons among different options in a considerably short time. This user-friendly simulation code is expected to be beneficial to further studies on the nuclear fuel cycle to find best options for the future all proliferation risk, environmental impact and economic costs considered.

Inventory and review of aquifer storage and recovery in southern Florida

Science.gov (United States)

Reese, Ronald S.

2002-01-01

publications > water resources investigations > report 02-4036 US Department of the Interior US Geological Survey WRI 02-4036Inventory and Review of Aquifer Storage and Recovery in Southern Florida By Ronald S. ReeseTallahassee, Florida 2002 prepared as part of the U.S. Geological Survey Place-Based Studies Program ABSTRACT Abstract Introduction Inventory of Data Case Studies Summary References Tables Aquifer storage and recovery in southern Florida has been proposed on an unprecedented scale as part of the Comprehensive Everglades Restoration Plan. Aquifer storage and recovery wells were constructed or are under construction at 27 sites in southern Florida, mostly by local municipalities or counties located in coastal areas. The Upper Floridan aquifer, the principal storage zone of interest to the restoration plan, is the aquifer being used at 22 of the sites. The aquifer is brackish to saline in southern Florida, which can greatly affect the recovery of the freshwater recharged and stored.Well data were inventoried and compiled for all wells at most of the 27 sites. Construction and testing data were compiled into four main categories: (1) well identification, location, and construction data; (2) hydraulic test data; (3) ambient formation water-quality data; and (4) cycle testing data. Each cycle during testing or operation includes periods of recharge of freshwater, storage, and recovery that each last days or months. Cycle testing data include calculations of recovery efficiency, which is the percentage of the total amount of potable water recharged for each cycle that is recovered.Calculated cycle test data include potable water recovery efficiencies for 16 of the 27 sites. However, the number of cycles at most sites was limited; except for two sites, the highest number of cycles was five. Only nine sites had a recovery efficiency above 10 percent for the first cycle, and 10 sites achieved a recovery efficiency above 30 percent during at least one cycle. The

Analysis of potential combustion source impacts on acid deposition using an independently derived inventory. Volume I

Energy Technology Data Exchange (ETDEWEB)

1983-12-01

This project had three major objectives. The first objective was to develop a fossil fuel combustion source inventory (NO/sub x/, SO/sub x/, and hydrocarbon emissions) that would be relatively easy to use and update for analyzing the impact of combustion emissions on acid deposition in the eastern United States. The second objective of the project was to use the inventory data as a basis for selection of a number of areas that, by virtue of their importance in the acid rain issue, could be further studied to assess the impact of local and intraregional combustion sources. The third objective was to conduct an analysis of wet deposition monitoring data in the areas under study, along with pertinent physical characteristics, meteorological conditions, and emission patterns of these areas, to investigate probable relationships between local and intraregional combustion sources and the deposition of acidic material. The combustion source emissions inventory has been developed for the eastern United States. It characterizes all important area sources and point sources on a county-by-county basis. Its design provides flexibility and simplicity and makes it uniquely useful in overall analysis of emission patterns in the eastern United States. Three regions with basically different emission patterns have been identified and characterized. The statistical analysis of wet deposition monitoring data in conjunction with emission patterns, wind direction, and topography has produced consistent results for each study area and has demonstrated that the wet deposition in each area reflects the characteristics of the localized area around the monitoring sites (typically 50 to 150 miles). 8 references, 28 figures, 39 tables.

National inventory of radioactive wastes and valorizable materials. Synthesis report; Inventaire national des dechets radioactifs et des matieres valorisables. Rapport de synthese

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This national inventory of radioactive wastes is a reference document for professionals and scientists of the nuclear domain and also for any citizen interested in the management of radioactive wastes. It contains: 1 - general introduction; 2 - the radioactive wastes: definition, classification, origin and management; 3 - methodology of the inventory: organization, accounting, prospective, production forecasting, recording of valorizable materials, exhaustiveness, verification tools; 4 - general results: radioactive waste stocks recorded until December 31, 2002, forecasts for the 2003-2020 era, post-2020 prospects: dismantling operations, recording of valorizable materials; 5 - inventory per producer or owner: front-end fuel cycle facilities, power generation nuclear centers, back-end fuel cycle facilities, waste processing or maintenance facilities, civil CEA research centers, non-CEA research centers, medical activities (diagnostics, therapeutics, analyses), various industrial activities (sources fabrication, control, particular devices), military research and experiment centers, storage and disposal facilities; 6 - elements about radioactive polluted sites; 7 - examples of foreign inventories; 8 - conclusion and appendixes. (J.S.)

A break-even analysis of RFID technology for inventory sensitive to shrinkage

NARCIS (Netherlands)

Kok, de A.G.; Donselaar, van K.H.; Woensel, van T.

2008-01-01

By embedding RFID tags onto their products, both manufacturers and retailers try to control for shrinkage (e.g. due to theft). Current inventory control systems do not take into account the disappearing inventory due to this shrinkage. As a response, corrective actions are made by performing costly

Distributed source term analysis, a new approach to nuclear material inventory verification

CERN Document Server

Beddingfield, D H

2002-01-01

The Distributed Source-Term Analysis (DSTA) technique is a new approach to measuring in-process material holdup that is a significant departure from traditional hold-up measurement methodology. The DSTA method is a means of determining the mass of nuclear material within a large, diffuse, volume using passive neutron counting. The DSTA method is a more efficient approach than traditional methods of holdup measurement and inventory verification. The time spent in performing DSTA measurement and analysis is a fraction of that required by traditional techniques. The error ascribed to a DSTA survey result is generally less than that from traditional methods. Also, the negative bias ascribed to gamma-ray methods is greatly diminished because the DSTA method uses neutrons which are more penetrating than gamma-rays.

Distributed source term analysis, a new approach to nuclear material inventory verification

International Nuclear Information System (INIS)

Beddingfield, D.H.; Menlove, H.O.

2002-01-01

The Distributed Source-Term Analysis (DSTA) technique is a new approach to measuring in-process material holdup that is a significant departure from traditional hold-up measurement methodology. The DSTA method is a means of determining the mass of nuclear material within a large, diffuse, volume using passive neutron counting. The DSTA method is a more efficient approach than traditional methods of holdup measurement and inventory verification. The time spent in performing DSTA measurement and analysis is a fraction of that required by traditional techniques. The error ascribed to a DSTA survey result is generally less than that from traditional methods. Also, the negative bias ascribed to γ-ray methods is greatly diminished because the DSTA method uses neutrons which are more penetrating than γ-rays

Data supporting the comparative life cycle assessment of different municipal solid waste management scenarios

Science.gov (United States)

Ali Rajaeifar, Mohammad; Tabatabaei, Meisam; Ghanavati, Hossein

2015-01-01

Environmental assessment of municipal solid waste (MSW) management scenarios would help to select eco-friendly scenarios. In this study, the inventory data in support of life cycle assessment of different MSW are presented. The scenarios were defined as: anaerobic digestion (AD, Sc-0), landfilling combined with composting (Sc-1), incineration (Sc-2), incineration combined with composting (Sc-3), and AD combined with incineration (Sc-4). The current article contains flowcharts of the different scenarios. Additionally, six supplementary files including inventory data on the different scenarios, data on the different damage assessment categories, normalization, and single scores are presented (Supplementary files 1–6). The analysis of the different scenarios revealed that the most eco-friendly scenario to be implemented in the future would be the combination of AD and incineration (Sc-4). PMID:26217743

Data supporting the comparative life cycle assessment of different municipal solid waste management scenarios

Directory of Open Access Journals (Sweden)

Mohammad Ali Rajaeifar

2015-06-01

Full Text Available Environmental assessment of municipal solid waste (MSW management scenarios would help to select eco-friendly scenarios. In this study, the inventory data in support of life cycle assessment of different MSW are presented. The scenarios were defined as: anaerobic digestion (AD, Sc-0, landfilling combined with composting (Sc-1, incineration (Sc-2, incineration combined with composting (Sc-3, and AD combined with incineration (Sc-4. The current article contains flowcharts of the different scenarios. Additionally, six supplementary files including inventory data on the different scenarios, data on the different damage assessment categories, normalization, and single scores are presented (Supplementary files 1–6. The analysis of the different scenarios revealed that the most eco-friendly scenario to be implemented in the future would be the combination of AD and incineration (Sc-4.

'Once through' cycles in the pebble bed HTR

International Nuclear Information System (INIS)

Teuchert, E.

1977-12-01

In the pebble bed HTR the 'Once Through' cycles achieve a favorable conservation of uranium resources due to their high burnup and due to the relatively low fissile inventory. A detailed study is given for cycles with highly enriched uranium and thorium, 20% enriched uranium and thorium, and for the low (approximately 8%) enriched cycle. The recommended cycle is based on the known THTR fuel element in the Th/U (93%) cycle. The variant with separate Seed elements and Breed elements presents the best pioneer in view of later recycling and thermal breeding. The minimum proliferation risk is achieved in the Th/U (20%) cycle basing on the fuel element type of the AVR, due to the low amount and high denaturization of the disloaded plutonium. (orig.) [de

Hanford regulated laundry: inventory control and production improvement study

Energy Technology Data Exchange (ETDEWEB)

Hostick, C. J.; Imhoff, C. H.; Levine, L. O.

1986-04-01

The purpose of this report is to assist the Hanford regulated laundry facility in reducing processing costs and in improving facility performance. Specific problem areas addressed were: no method for determining optimum manpower requirements, resulting in excessive amounts of employee overtime; no buffer inventory available to offset demand peaks, resulting in additional employee overtime and unmet demand; lack of adequate inventory control, resulting in unnecessary inventory costs; and no detailed analysis of the impact of 100% monitoring.

Constructing the Japanese version of the Maslach Burnout Inventory-Student Survey: Confirmatory factor analysis.

Science.gov (United States)

Tsubakita, Takashi; Shimazaki, Kazuyo

2016-01-01

To examine the factorial validity of the Maslach Burnout Inventory-Student Survey, using a sample of 2061 Japanese university students majoring in the medical and natural sciences (67.9% male, 31.8% female; Mage  = 19.6 years, standard deviation = 1.5). The back-translated scale used unreversed items to assess inefficacy. The inventory's descriptive properties and Cronbach's alphas were calculated using SPSS software. The present authors compared fit indices of the null, one factor, and default three factor models via confirmatory factor analysis with maximum-likelihood estimation using AMOS software, version 21.0. Intercorrelations between exhaustion, cynicism, and inefficacy were relatively higher than in prior studies. Cronbach's alphas were 0.76, 0.85, and 0.78, respectively. Although fit indices of the hypothesized three factor model did not meet the respective criteria, the model demonstrated better fit than did the null and one factor models. The present authors added four paths between error variables within items, but the modified model did not show satisfactory fit. Subsequent analysis revealed that a bi-factor model fit the data better than did the hypothesized or modified three factor models. The Japanese version of the Maslach Burnout Inventory-Student Survey needs minor changes to improve the fit of its three factor model, but the scale as a whole can be used to adequately assess overall academic burnout in Japanese university students. Although the scale was back-translated, two items measuring exhaustion whose expressions overlapped should be modified, and all items measuring inefficacy should be reversed in order to statistically clarify the factorial difference between the scale's three factors. © 2015 The Authors. Japan Journal of Nursing Science © 2015 Japan Academy of Nursing Science.

Analysis of interconnecting energy systems over a synchronized life cycle

International Nuclear Information System (INIS)

Nian, Victor

2016-01-01

Highlights: • A methodology is developed for evaluating a life cycle of interconnected systems. • A new concept of partial temporal boundary is introduced via quantitative formulation. • The interconnecting systems are synchronized through the partial temporal boundary. • A case study on the life cycle of the coal–uranium system is developed. - Abstract: Life cycle analysis (LCA) using the process chain analysis (PCA) approach has been widely applied to energy systems. When applied to an individual energy system, such as coal or nuclear electricity generation, an LCA–PCA methodology can yield relatively accurate results with its detailed process representation based on engineering data. However, there are fundamental issues when applying conventional LCA–PCA methodology to a more complex life cycle, namely, a synchronized life cycle of interconnected energy systems. A synchronized life cycle of interconnected energy systems is established through direct interconnections among the processes of different energy systems, and all interconnecting systems are bounded within the same timeframe. Under such a life cycle formation, there are some major complications when applying conventional LCA–PCA methodology to evaluate the interconnecting energy systems. Essentially, the conventional system and boundary formulations developed for a life cycle of individual energy system cannot be directly applied to a life cycle of interconnected energy systems. To address these inherent issues, a new LCA–PCA methodology is presented in this paper, in which a new concept of partial temporal boundary is introduced to synchronize the interconnecting energy systems. The importance and advantages of these new developments are demonstrated through a case study on the life cycle of the coal–uranium system.

Analysis on the fuel cycle requirements of the FR systems

International Nuclear Information System (INIS)

Maki, Takashi; Horiuchi, Nobutake

2003-01-01

The functions of the nuclear fuel cycle amount analysis code, developed in 2002 were extended. This code calculates the change in characteristics with time of mass balance (for example, the amount of natural uranium demand, plutonium mass balance, environmental load reduction, etc.) in nuclear fuel cycles, to examine the state of future reactor types or recycling facilities. In 2003, as for this code, calculation functions of automatic adjustment of FR capacity, LWR's recovery minor actinide (MA) recycling, were added, and the I/O function was improved according to it. Moreover, benchmark calculation to the extended amount analysis code was performed using the other tool, and it was confirmed that mass balance was calculated appropriately. Furthermore, the mass balance of a few typical FR cycle concepts was calculated with this analysis code, and the further of each concept was clarified. (author)

Mapping Forest Inventory and Analysis forest land use: timberland, reserved forest land, and other forest land

Science.gov (United States)

Mark D. Nelson; John Vissage

2007-01-01

The Forest Inventory and Analysis (FIA) program produces area estimates of forest land use within three subcategories: timberland, reserved forest land, and other forest land. Mapping these subcategories of forest land requires the ability to spatially distinguish productive from unproductive land, and reserved from nonreserved land. FIA field data were spatially...

Management of actinide waste inventories in nuclear phase-out scenarios

International Nuclear Information System (INIS)

Cometto, M.; Wydler, P.; Chawla, R.

2008-01-01

The improvement of the 'radiological cleanliness' of nuclear energy is a primary goal in the development of advanced reactors and fuel cycles. The multiple recycling of actinides in advanced nuclear systems with fast neutron spectra represents a key option for reducing the potential hazard from high-level waste, especially when the fuel cycle is fully closed. Such strategies, however, involve large inventories of radiotoxic, transuranic (TRU) nuclides in the nuclear park, both in-pile and out-of-pile. The management of these inventories with the help of actinide burners is likely to become an important issue, if nuclear energy systems are eventually phased out, i.e. replaced by other types of energy systems. The present paper compares phase-out scenarios for two transmutation strategies involving fast reactors (FRs) and accelerator-driven systems (ADSs), respectively, operating in symbiosis with conventional light water reactors (LWRs). Particular objectives are to evaluate and compare the TRU reduction performance of the systems as a function of the phase-out time and to determine the appropriate phase-out length for different phase-out criteria. In this connection, an interesting aspect concerns the continuous optimisation of the fuel cycle to counterbalance the reactivity decrease due to the depletion of the fissile isotopes in the fuel. It will be shown that both FRs and ADSs can achieve the goal, provided that the phase-out operation can be continued for about a hundred years

Confirmatory Factor Analysis of the Trinity Inventory of Precursors to Suicide (TIPS) and Its Relationship to Hopelessness and Depression

Science.gov (United States)

Smyth, Caroline L.; MacLachlan, Malcolm

2005-01-01

Numerous existing measures assess attitudes toward suicide yet fail to account for contextual factors. The Trinity Inventory of Precursors to Suicide (TIPS) is presented as an alternative, with implications for the development of prevention programs. Having previously reported exploratory analysis of the TIPS; confirmatory factor analysis and…

EMERGY ANALYSIS OF THE PREHISTORIC NITROGEN CYCLE

Science.gov (United States)

Several relationships between the specific emergy or the emergy per unit mass and the mass concentration of nitrogen were shown to exist through an analysis of the global nitrogen cycle. These observed relationships were interpreted by examining the nature of the underlying ener...

Tritium inventory control--the experience with DT tokamaks and its relevance for future machines

International Nuclear Information System (INIS)

Bell, A.C.; Gentile, C.A.; Laesser, R.L.K.; Coad, J.P.

2003-01-01

At present, the commercial use of tritium is relatively small scale. The main source of supply is as a by-product of heavy water moderated fission reactors and the products are mainly discrete sources or tracers with activity typically in the GBq range. There are in general no restrictions on the use of tritium other than those, which would normally apply to the use of radioactive material. The future use of tritium as intermediate fuel for a fusion power plant series will involve an increase by several orders of magnitude in the industrial use of tritium and may increase concerns relating to safety, transport and waste disposal. In addition, the use of tritium in fusion power will be unable to be satisfied by current sources of supply and tritium production in future fusion power plants will be essential for the operation of the plants as well as for the start of new ones. Power plant studies have, however, shown that these issues can be satisfactorily addressed. In addition the values for clearance of tritiated materials in a number of countries are consistent with the low environmental impact of disposal of tritiated waste. There are, however, many practical operational and regulatory problems, which will need to be solved in the context of the experimental programmes. The current regulations for control and accountancy of tritium inventory, as applied internationally and in specific countries, are reviewed and their influence on the DT fuel cycle considered. The effect of safety case limits on the need for control of tritium inventory in TFTR, JET and ITER is analysed. The sensitivity of the fuel cycle to tritium inventory is considered. The experience of controlling tritium inventory in TFTR and JET is reviewed and the latest results from JET presented. This takes into account the limits and constraints, the differing requirements for tritium processing, in-vessel retention, the needs for waste management and decommissioning including detritiation, and

Spatially explicit analysis of field inventories for national forest carbon monitoring

Directory of Open Access Journals (Sweden)

David C. Marvin

2016-06-01

Full Text Available Abstract Background Tropical forests provide a crucial carbon sink for a sizable portion of annual global CO2 emissions. Policies that incentivize tropical forest conservation by monetizing forest carbon ultimately depend on accurate estimates of national carbon stocks, which are often based on field inventory sampling. As an exercise to understand the limitations of field inventory sampling, we tested whether two common field-plot sampling approaches could accurately estimate carbon stocks across approximately 76 million ha of Perúvian forests. A 1-ha resolution LiDAR-based map of carbon stocks was used as a model of the country’s carbon geography. Results Both field inventory sampling approaches worked well in estimating total national carbon stocks, almost always falling within 10 % of the model national total. However, the sampling approaches were unable to produce accurate spatially-explicit estimates of the carbon geography of Perú, with estimates falling within 10 % of the model carbon geography across no more than 44 % of the country. We did not find any associations between carbon stock errors from the field plot estimates and six different environmental variables. Conclusions Field inventory plot sampling does not provide accurate carbon geography for a tropical country with wide ranging environmental gradients such as Perú. The lack of association between estimated carbon errors and environmental variables suggests field inventory sampling results from other nations would not differ from those reported here. Tropical forest nations should understand the risks associated with primarily field-based sampling approaches, and consider alternatives leading to more effective forest conservation and climate change mitigation.

A Perishable Inventory Model with Return

Science.gov (United States)

Setiawan, S. W.; Lesmono, D.; Limansyah, T.

2018-04-01

In this paper, we develop a mathematical model for a perishable inventory with return by assuming deterministic demand and inventory dependent demand. By inventory dependent demand, it means that demand at certain time depends on the available inventory at that time with certain rate. In dealing with perishable items, we should consider deteriorating rate factor that corresponds to the decreasing quality of goods. There are also costs involved in this model such as purchasing, ordering, holding, shortage (backordering) and returning costs. These costs compose the total costs in the model that we want to minimize. In the model we seek for the optimal return time and order quantity. We assume that after some period of time, called return time, perishable items can be returned to the supplier at some returning costs. The supplier will then replace them in the next delivery. Some numerical experiments are given to illustrate our model and sensitivity analysis is performed as well. We found that as the deteriorating rate increases, returning time becomes shorter, the optimal order quantity and total cost increases. When considering the inventory-dependent demand factor, we found that as this factor increases, assuming a certain deteriorating rate, returning time becomes shorter, optimal order quantity becomes larger and the total cost increases.

Exergy analysis of helium liquefaction systems based on modified Claude cycle with two-expanders

Science.gov (United States)

Thomas, Rijo Jacob; Ghosh, Parthasarathi; Chowdhury, Kanchan

2011-06-01

Large-scale helium liquefaction systems, being energy-intensive, demand judicious selection of process parameters. An effective tool for design and analysis of thermodynamic cycles for these systems is exergy analysis, which is used to study the behavior of a helium liquefaction system based on modified Claude cycle. Parametric evaluation using process simulator Aspen HYSYS® helps to identify the effects of cycle pressure ratio and expander flow fraction on the exergetic efficiency of the liquefaction cycle. The study computes the distribution of losses at different refrigeration stages of the cycle and helps in selecting optimum cycle pressures, operating temperature levels of expanders and mass flow rates through them. Results from the analysis may help evolving guidelines for designing appropriate thermodynamic cycles for practical helium liquefaction systems.

Estimating down dead wood from FIA forest inventory variables in Maine

Science.gov (United States)

David C. Chojnacky; Linda S. Heath

2002-01-01

Down deadwood (DDW) is a carbon component important in the function and structure of forest ecosystems, but estimating DDW is problematic because these data are not widely available in forest inventory databases. However, DDW data were collected on USDA Forest Service Forest Inventory and Analysis (FIA) plots during Maine's 1995 inventory. This study examines ways...

International inventory of training facilities in nuclear power and its fuel cycle 1978