WorldWideScience

Sample records for current plasma discharge

  1. Dynamics of the plasma current sheath in plasma focus discharges in different gases

    Energy Technology Data Exchange (ETDEWEB)

    Vinogradov, V. P.; Krauz, V. I., E-mail: krauz-vi@nrcki.ru [National Research Center Kurchatov Institute (Russian Federation); Mokeev, A. N. [Project Center ITER (Russian Federation); Myalton, V. V.; Kharrasov, A. M. [National Research Center Kurchatov Institute (Russian Federation)

    2016-12-15

    The shape of the plasma current sheath (PCS) in the final stage of its radial compression, the dynamics of pinching, and the subsequent pinch decay in plasma focus (PF) discharges in different gases are studied using an improved multichannel system of electron-optical plasma photography and a newly elaborated synchronization system. The PCS structure in discharges in heavy gases (Ne, Ar) is found to differ significantly from that in discharges in hydrogen and deuterium. The influence of a heavy gas (Xe) additive to hydrogen and deuterium on the structure and compression dynamics of the PCS is investigated.

  2. A diagnostic system for electrical faults in a high current discharge plasma setup

    Energy Technology Data Exchange (ETDEWEB)

    Nigam, S.; Aneesh, K.; Navathe, C. P.; Gupta, P. D. [Raja Ramanna Centre for Advanced Technology, Indore 452013 (India)

    2011-02-15

    A diagnostic system to detect electrical faults inside a coaxial high current discharge device is presented here. This technique utilizes two biconical antennas picking up electromagnetic radiation from the discharge device, a voltage divider sensing input voltage, and a Rogowski coil measuring the main discharge current. A computer program then analyses frequency components in these signals and provides information as to whether the discharge event was normal or any breakdown fault occurred inside the coaxial device. The diagnostic system is developed for a 450 kV and 50 kA capillary discharge plasma setup. For the setup various possible faults are analyzed by electrical simulation, followed by experimental results. In the case of normal discharge through the capillary load the dominant frequency is {approx}4 MHz. Under faulty conditions, the peak in magnitude versus frequency plot of the antenna signal changes according to the fault position which involves different paths causing variation in the equivalent circuit elements.

  3. A diagnostic system for electrical faults in a high current discharge plasma setup.

    Science.gov (United States)

    Nigam, S; Aneesh, K; Navathe, C P; Gupta, P D

    2011-02-01

    A diagnostic system to detect electrical faults inside a coaxial high current discharge device is presented here. This technique utilizes two biconical antennas picking up electromagnetic radiation from the discharge device, a voltage divider sensing input voltage, and a Rogowski coil measuring the main discharge current. A computer program then analyses frequency components in these signals and provides information as to whether the discharge event was normal or any breakdown fault occurred inside the coaxial device. The diagnostic system is developed for a 450 kV and 50 kA capillary discharge plasma setup. For the setup various possible faults are analyzed by electrical simulation, followed by experimental results. In the case of normal discharge through the capillary load the dominant frequency is ∼4 MHz. Under faulty conditions, the peak in magnitude versus frequency plot of the antenna signal changes according to the fault position which involves different paths causing variation in the equivalent circuit elements.

  4. A diagnostic system for electrical faults in a high current discharge plasma setup

    Science.gov (United States)

    Nigam, S.; Aneesh, K.; Navathe, C. P.; Gupta, P. D.

    2011-02-01

    A diagnostic system to detect electrical faults inside a coaxial high current discharge device is presented here. This technique utilizes two biconical antennas picking up electromagnetic radiation from the discharge device, a voltage divider sensing input voltage, and a Rogowski coil measuring the main discharge current. A computer program then analyses frequency components in these signals and provides information as to whether the discharge event was normal or any breakdown fault occurred inside the coaxial device. The diagnostic system is developed for a 450 kV and 50 kA capillary discharge plasma setup. For the setup various possible faults are analyzed by electrical simulation, followed by experimental results. In the case of normal discharge through the capillary load the dominant frequency is ˜4 MHz. Under faulty conditions, the peak in magnitude versus frequency plot of the antenna signal changes according to the fault position which involves different paths causing variation in the equivalent circuit elements.

  5. Plasma Emission Characteristics from a High Current Hollow Cathode in an Ion Thruster Discharge Chamber

    Science.gov (United States)

    Foster, John E.; Patterson, Michael J.

    2002-01-01

    The presence of energetic ions produced by a hollow cathodes operating at high emission currents (greater than 5A) has been documented in the literature. In order to further elucidate these findings, an investigation of a high current cathode operating in an ion thruster discharge chamber has been undertaken. Using Langmuir probes, a low energy charged particle analyzer and emission spectroscopy, the behavior of the near-cathode plasma and the emitted ion energy distribution was characterized. The presence of energetic ions was confirmed. It was observed that these ions had energies in excess of the discharge voltage and thus cannot be simply explained by ions falling out of plasma through a potential difference of this order. Additionally, evidence provided by Langmuir probes suggests the existence of a double layer essentially separating the hollow cathode plasma column from the main discharge. The radial potential difference associated with this double layer was measured to be of order the ionization potential.

  6. Mechanism behind self-sustained oscillations in direct current glow discharges and in dusty plasmas

    CERN Document Server

    Cho, Sung Nae

    2013-01-01

    An alternative explanation to the mechanism behind self-sustained oscillations of ions in direct current (DC) glow discharges is provided. Such description is distinguished from the one provided by fluid models, where oscillations are attributed to positive feedback mechanism associated with photoionization of particles and photoemission of electrons from the cathode. Here, oscillations arise as consequence of interaction between an ion and surface charges induced by it at the bounding electrodes. Such mechanism provides an elegant explanation to why self-sustained oscillations occur only in the negative resistance region of the voltage-current characteristic curve in DC glow discharges. It is found that oscillation frequencies increase with ion's surface charge density, but at the rate which is significantly slower than it does with electric field. The presented mechanism also describes the self-sustained oscillations of ions in dusty plasmas, demonstrating that oscillations in dusty plasmas and DC glow disc...

  7. Direct Current Magnetron Glow Discharge Plasma Characteristics Study for Controlled Deposition of Titanium Nitride Thin Film

    Directory of Open Access Journals (Sweden)

    Sankar Moni Borah

    2013-01-01

    Full Text Available This paper reports on the study of direct current (DC magnetron glow discharge plasma characteristics in a cylindrical magnetron system in argon-nitrogen. Presence of nitrogen gas makes the plasma environment reactive, and it results in significant changes of the plasma properties—number density, electron temperature, floating potential, and sheath thickness. Applied magnetic field is a parameter which is closely related to proper deposition of thin film. Cylindrical Langmuir probe and Emissive probe are used as diagnostics for the estimation of various plasma parameters indicated earlier. Controlled titanium nitride (TiN thin film deposition on bell-metal at different argon-nitrogen gases ratio is another important study reported.

  8. Plasma characteristics in the discharge region of a 20 A emission current hollow cathode

    Science.gov (United States)

    Mingming, SUN; Tianping, ZHANG; Xiaodong, WEN; Weilong, GUO; Jiayao, SONG

    2018-02-01

    Numerical calculation and fluid simulation methods were used to obtain the plasma characteristics in the discharge region of the LIPS-300 ion thruster’s 20 A emission current hollow cathode and to verify the structural design of the emitter. The results of the two methods indicated that the highest plasma density and electron temperature, which improved significantly in the orifice region, were located in the discharge region of the hollow cathode. The magnitude of plasma density was about 1021 m‑3 in the emitter and orifice regions, as obtained by numerical calculations, but decreased exponentially in the plume region with the distance from the orifice exit. Meanwhile, compared to the emitter region, the electron temperature and current improved by about 36% in the orifice region. The hollow cathode performance test results were in good agreement with the numerical calculation results, which proved that that the structural design of the emitter and the orifice met the requirements of a 20 A emission current. The numerical calculation method can be used to estimate plasma characteristics in the preliminary design stage of hollow cathodes.

  9. Nonlocal control of electron temperature in short direct current glow discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Demidov, V. I. [Department of Optics and Spectroscopy, St. Petersburg State University, St. Petersburg 199034 (Russian Federation); International Laboratory “Nonlocal Plasma in Nanotechnology and Medicine”, ITMO University, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); Department of Physics and Astronomy, West Virginia University, Morgantown, West Virginia 26506 (United States); Kudryavtsev, A. A.; Stepanova, O. M. [Department of Optics and Spectroscopy, St. Petersburg State University, St. Petersburg 199034 (Russian Federation); Kurlyandskaya, I. P. [International Laboratory “Nonlocal Plasma in Nanotechnology and Medicine”, ITMO University, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); St. Petersburg University of State Fire Service of EMERCOM RF, Murmansk Branch, Murmansk 183040 (Russian Federation)

    2014-09-15

    To demonstrate controlling the electron temperature in nonlocal plasma, experiments have been performed on a short (without positive column) dc glow discharge with a cold cathode by applying different voltages to the conducting discharge wall. The experiments have been performed for low-pressure noble gas discharges. The applied voltage can modify trapping the energetic electrons emitted from the cathode sheath and arising from the atomic and molecular processes in the plasma within the device volume. This phenomenon results in the energetic electrons heating the slow plasma electrons, which consequently modifies the electron temperature. Furthermore, a numerical model of the discharge has demonstrated the electron temperature modification for the above case.

  10. Control of plasma properties in a short direct-current glow discharge with active boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Adams, S. F. [Air Force Research Laboratory, WPAFB, Ohio 45433 (United States); Demidov, V. I., E-mail: vladimir.demidov@mail.wvu.edu [Air Force Research Laboratory, WPAFB, Ohio 45433 (United States); West Virginia University, Morgantown, West Virginia 26506 (United States); Bogdanov, E. A.; Kudryavtsev, A. A. [St. Petersburg State University, St. Petersburg 199034 (Russian Federation); Koepke, M. E. [West Virginia University, Morgantown, West Virginia 26506 (United States); Kurlyandskaya, I. P. [St. Petersburg University of State Fire Service of EMERCOM RF, Murmansk Branch, Murmansk 183040 (Russian Federation)

    2016-02-15

    To demonstrate controlling electron/metastable density ratio and electron temperature by applying negative voltages to the active (conducting) discharge wall in a low-pressure plasma with nonlocal electron energy distribution function, modeling has been performed in a short (lacking the positive-column region) direct-current glow discharge with a cold cathode. The applied negative voltage can modify the trapping of the low-energy part of the energetic electrons that are emitted from the cathode sheath and that arise from the atomic and molecular processes in the plasma within the device volume. These electrons are responsible for heating the slow, thermal electrons, while production of slow electrons (ions) and metastable atoms is mostly due to the energetic electrons with higher energies. Increasing electron temperature results in increasing decay rate of slow, thermal electrons (ions), while decay rate of metastable atoms and production rates of slow electrons (ions) and metastable atoms practically are unchanged. The result is in the variation of electron/metastable density ratio and electron temperature with the variation of the wall negative voltage.

  11. Development of soft ionization using direct current pulse glow discharge plasma source in mass spectrometry for volatile organic compounds analysis

    Science.gov (United States)

    Nunome, Yoko; Kodama, Kenji; Ueki, Yasuaki; Yoshiie, Ryo; Naruse, Ichiro; Wagatsuma, Kazuaki

    2018-01-01

    This study describes an ionization source for mass analysis, consisting of glow discharge plasma driven by a pulsed direct-current voltage for soft plasma ionization, to detect toxic volatile organic compounds (VOCs) rapidly and easily. The novelty of this work is that a molecular adduct ion, in which the parent molecule attaches with an NO+ radical, [M + NO]+, can be dominantly detected as a base peak with little or no fragmentation of them in an ambient air plasma at a pressure of several kPa. Use of ambient air as the discharge plasma gas is suitable for practical applications. The higher pressure in an ambient air discharge provided a stable glow discharge plasma, contributing to the soft ionization of organic molecules. Typical mass spectra of VOCs toluene, benzene, o-xylene, chlorobenzene and n-hexane were observed as [M + NO]+ adduct ion whose peaks were detected at m/z 122, 108, 136, 142 and 116, respectively. The NO generation was also confirmed by emission bands of NO γ-system. The ionization reactions were suggested, such that NO+ radical formed in an ambient air discharge could attach with the analyte molecule.

  12. ULTRAVIOLET INDUCED MOTION OF A FLUORESCENT DUST CLOUD IN AN ARGON DIRECT CURRENT GLOW DISCHARGE PLASMA

    Energy Technology Data Exchange (ETDEWEB)

    Hvasta, M.G.; and Zwicker, A.

    2008-01-01

    Dusty plasmas consist of electrons, ions, neutrals and nm-μm sized particles commonly referred to as dust. In man-made plasmas this dust may represent impurities in a tokamak or plasma etching processing. In astrophysical plasmas this dust forms structures such as planetary rings and comet tails. To study dusty plasma dynamics an experiment was designed in which a 3:1 silica (<5 μm diameter) and fl uorescent dust mixture was added to an argon DC glow discharge plasma and exposed to UV radiation. This fl uorescent lighting technique offers an advantage over laser scattering (which only allows two-dimensional slices of the cloud to be observed) and is simpler than scanning mirror techniques or particle image velocimetry. Under typical parameters (P=150 mTorr, V anode= 100 V, Vcathode= -400 V, Itotal < 2mA) when the cloud is exposed to the UV light (100W, λ = 365 nm) the mixture fl uoresces, moves ~2mm towards the light source and begins rotating in a clockwise manner (as seen from the cathode). By calibrating a UV lamp and adjusting the relative intensity of the UV with a variable transformer it was found that both translational and rotational velocities are a function of UV intensity. Additionally, it was determined that bulk cloud rotation is not seen when the dust tray is not grounded while bulk translation is. This ongoing experiment represents a novel way to control contamination in man-made plasmas and a path to a better understanding of UV-bathed plasma systems in space..

  13. Current-voltage characteristics of a cathodic plasma contactor with discharge chamber for application in electrodynamic tether propulsion

    Science.gov (United States)

    Xie, Kan; Martinez, Rafael A.; Williams, John D.

    2014-04-01

    This paper focuses on the net electron-emission current as a function of bias voltage of a plasma source that is being used as the cathodic element in a bare electrodynamic tether system. An analysis is made that enables an understanding of the basic issues determining the current-voltage (C-V) behaviour. This is important for the efficiency of the electrodynamic tether and for low impedance performance without relying on the properties of space plasma for varying orbital altitudes, inclinations, day-night cycles or the position of the plasma contactor relative to the wake of the spacecraft. The cathodic plasma contactor considered has a cylindrical discharge chamber (10 cm in diameter and ˜11 cm in length) and is driven by a hollow cathode. Experiments and a 1D spherical model are both used to study the contactor's C-V curves. The experiments demonstrate how the cathodic contactor would emit electrons into space for anode voltages in the range of 25-40 V, discharge currents in the range of 1-2.5 A, and low xenon gas flows of 2-4 sccm. Plasma properties are measured and compared with (3 A) and without net electron emission. A study of the dependence of relevant parameters found that the C-V behaviour strongly depends on electron temperature, initial ion energy and ion emission current at the contactor exit. However, it depended only weakly on ambient plasma density. The error in the developed model compared with the experimental C-V curves is within 5% at low electron-emission currents (0-2 A). The external ionization processes and high ion production rate caused by the discharge chamber, which dominate the C-V behaviour at electron-emission currents over 2 A, are further highlighted and discussed.

  14. Long-lived Ar-Hg plasma in the afterglow of a high-current pulsed discharge

    Energy Technology Data Exchange (ETDEWEB)

    Sergeichev, K. F.; Lukina, N. A.; Fesenko, A. A. [Russian Academy of Sciences, Prokhorov General Physics Institute (Russian Federation)

    2013-02-15

    High-density (n > 10{sup 12} cm{sup -3}) argon-mercury plasma produced by a short (t {approx} 20 {mu}s) high-power pulsed discharge in argon with an admixture of mercury vapor at a discharge current of {approx}50 A, an argon pressure of {approx}4 mm Hg, and a mercury vapor pressure of {approx}10{sup -3} mm Hg was studied using optical spectroscopy and radio physics methods. It is found that the lifetime of this plasma after the end of the discharge pulse is up to 10{sup -2} s. It is shown that such an abnormally long lifetime of such an afterglow plasma, as compared to the plasma of an argon discharge without an admixture of mercury vapor, is related to the long residence time of atoms and ions of both argon and mercury in highly excited states due to chemi-ionization processes involving long-lived metastable argon ions. It is suggested that dissociative recombination of highly excited molecular ions of argon play an important role in the transfer of excitation to argon atoms and ions that are close to autoionization states.

  15. Theory of gas discharge plasma

    CERN Document Server

    Smirnov, Boris M

    2015-01-01

    This book presents the theory of gas discharge plasmas in a didactical way. It explains the processes in gas discharge plasmas. A gas discharge plasma is an ionized gas which is supported by an external electric field. Therefore its parameters are determined by processes in it. The properties of a gas discharge plasma depend on its gas component, types of external fields, their geometry and regimes of gas discharge. Fundamentals of a gas discharge plasma include elementary, radiative and transport processes which are included in its kinetics influence. They are represented in this book together with the analysis of simple gas discharges. These general principles are applied to stationary gas discharge plasmas of helium and argon. The analysis of such plasmas under certain conditions is theoretically determined by numerical plasma parameters for given regimes and conditions.

  16. Infrared gas phase study on plasma-polymer interactions in high-current diffuse dielectric barrier discharge

    Science.gov (United States)

    Liu, Y.; Welzel, S.; Starostin, S. A.; van de Sanden, M. C. M.; Engeln, R.; de Vries, H. W.

    2017-06-01

    A roll-to-roll high-current diffuse dielectric barrier discharge at atmospheric pressure was operated in air and Ar/N2/O2 gas mixtures. The exhaust gas from the discharge was studied using a high-resolution Fourier-transform infrared spectrometer in the range from 3000 to 750 cm-1 to unravel the plasma-polymer interactions. The absorption features of HxNyOz, COx, and HCOOH (formic acid) were identified, and the relative densities were deduced by fitting the absorption bands of the detected molecules. Strong interactions between plasma and polymer (Polyethylene-2,6-naphthalate, or PEN) in precursor-free oxygen-containing gas mixtures were observed as evidenced by a high COx production. The presence of HCOOH in the gas effluent, formed through plasma-chemical synthesis of COx, turns out to be a sensitive indicator for etching. By adding tetraethylorthosilicate precursor in the plasma, dramatic changes in the COx production were measured, and two distinct deposition regimes were identified. At high precursor flows, a good agreement with the precursor combustion and the COx production was observed, whereas at low precursor flows an etching-deposition regime transpires, and the COx production is dominated by polymer etching.

  17. Modeling electronegative plasma discharge

    Energy Technology Data Exchange (ETDEWEB)

    Lichtenberg, A.J.; Lieberman, M.A. [Univ. of California, Berkley, CA (United States)

    1995-12-31

    Macroscopic analytic models for a three-component electronegative gas discharge are developed. Assuming the negative ions to be in Boltzmann equilibrium, a positive ion ambipolar diffusion equation is derived. The discharge consists of an electronegative core and electropositive edges. The electron density in the core is nearly uniform, allowing a parabolic approximation to the plasma profile to be employed. The resulting equilibrium equations are solved analytically and matched to a constant mobility transport model of an electropositive edge plasma. The solutions are compared to a simulation of a parallel-plane r.f. driven oxygen plasma for p = 50 mTorr and n{sub eo}= 2.4 x 10{sup 15} m{sup -3}. The ratio {alpha}{sub o} of central negative ion density to electron density, and the electron temperature T{sub e}, found in the simulation, are in reasonable agreement with the values calculated from the model. The model is extended to: (1) low pressures, where a variable mobility model is used in the electropositive edge region; and (2) high {alpha}{sub o} in which the edge region disappears. The inclusion of a second positive ion species, which can be very important in describing electronegative discharges used for materials processing, is a possible extension of the model.

  18. Exploring X-ray lasing in nitrogen pinch plasma at very high and fast discharge current excitation

    Science.gov (United States)

    Barnwal, S.; Nigam, S.; Aneesh, K.; Prasad, Y. B. S. R.; Sharma, M. L.; Tripathi, P. K.; Joshi, A. S.; Naik, P. A.; Vora, H. S.; Gupta, P. D.

    2017-06-01

    The possibility to demonstrate X-ray lasing in nitrogen at 13.4 nm through recombination scheme driven by capillary discharge excitation has been explored at a high discharge current of 95 kA, with 46 ns quarter period. The emission from nitrogen pinch plasma showed a fast pulse at the instant of pinch formation, overriding the long duration Bremsstrahlung emission. The spectroscopic study revealed dominant X-ray line emissions at 2.8 and 2.1 nm, apart from various X-ray line emissions at higher wavelengths. Line emission at 2.8 nm confirms the formation of NVI charge state of nitrogen. At lower pressures, faint emission of Ly-α line at 2.4 nm indicated formation of NVII ions by further heating. The favourable role of pre-pulse in the formation of higher charge states of nitrogen was also established beyond doubt. This study provides important inputs for future experiments towards demonstration of X-ray lasing at 13.4 nm.

  19. Chemical mechanisms inducing a dc current measured in the flowing post-discharge of an RF He-O2 plasma torch

    CERN Document Server

    Dufour, Thierry; Vandencasteele, N; Reniers, F

    2016-01-01

    The post-discharge of an RF plasma torch supplied with helium and oxygen gases is characterized by mass spectrometry, optical emission spectroscopy and electrical measurements. We have proved the existence of a dc current in the post-discharge (1--20 A), attributed to the Penning ionization of atmospheric nitrogen and oxygenated species. The mechanisms ruling this dc current are investigated through experiments in which we discuss the influence of the O2 flow rate, the He flow rate and the distance separating the plasma torch from a material surface located downstream.

  20. Constricted glow discharge plasma source

    Science.gov (United States)

    Anders, Andre; Anders, Simone; Dickinson, Michael; Rubin, Michael; Newman, Nathan

    2000-01-01

    A constricted glow discharge chamber and method are disclosed. The polarity and geometry of the constricted glow discharge plasma source is set so that the contamination and energy of the ions discharged from the source are minimized. The several sources can be mounted in parallel and in series to provide a sustained ultra low source of ions in a plasma with contamination below practical detection limits. The source is suitable for applying films of nitrides such as gallium nitride and oxides such as tungsten oxide and for enriching other substances in material surfaces such as oxygen and water vapor, which are difficult process as plasma in any known devices and methods. The source can also be used to assist the deposition of films such as metal films by providing low-energy ions such as argon ions.

  1. Plasma Discharge Process in a Pulsed Diaphragm Discharge System

    Science.gov (United States)

    Duan, Jianjin; Hu, Jue; Zhang, Chao; Wen, Yuanbin; Meng, Yuedong; Zhang, Chengxu

    2014-12-01

    As one of the most important steps in wastewater treatment, limited study on plasma discharge process is a key challenge in the development of plasma applications. In this study, we focus on the plasma discharge process of a pulsed diaphragm discharge system. According to the analysis, the pulsed diaphragm discharge proceeds in seven stages: (1) Joule heating and heat exchange stage; (2) nucleated site formation; (3) plasma generation (initiation of the breakdown stage); (4) avalanche growth and plasma expansion; (5) plasma contraction; (6) termination of the plasma discharge; and (7) heat exchange stage. From this analysis, a critical voltage criterion for breakdown is obtained. We anticipate this finding will provide guidance for a better application of plasma discharges, especially diaphragm plasma discharges.

  2. Toroidal current profile control during low confinement mode plasma discharges in DIII-D via first-principles-driven model-based robust control synthesis

    Science.gov (United States)

    Barton, Justin E.; Boyer, Mark D.; Shi, Wenyu; Schuster, Eugenio; Luce, Tim C.; Ferron, John R.; Walker, Michael L.; Humphreys, David A.; Penaflor, Ben G.; Johnson, Robert D.

    2012-12-01

    In order for ITER to be capable of operating in advanced tokamak operating regimes, characterized by a high fusion gain, good plasma confinement, magnetohydrodynamic stability and a non-inductively driven plasma current, for extended periods of time, several challenging plasma control problems still need to be solved. Setting up a suitable toroidal current density profile in the tokamak is key for one possible advanced operating scenario characterized by non-inductive sustainment of the plasma current. At the DIII-D tokamak, the goal is to create the desired current profile during the ramp-up and early flat-top phases of the plasma discharge and then actively maintain this target profile for the remainder of the discharge. The evolution in time of the toroidal current profile in tokamaks is related to the evolution of the poloidal magnetic flux profile, which is modelled in normalized cylindrical coordinates using a first-principles, nonlinear, dynamic partial differential equation (PDE) referred to as the magnetic diffusion equation. The magnetic diffusion equation is combined with empirical correlations developed from physical observations and experimental data from DIII-D for the electron temperature, the plasma resistivity and the non-inductive current drive to develop a simplified, control-oriented, nonlinear, dynamic PDE model of the poloidal flux profile evolution valid for low confinement mode discharges. In this work, we synthesize a robust feedback controller to reject disturbances and track a desired reference trajectory of the poloidal magnetic flux gradient profile by employing the control-oriented model of the system. A singular value decomposition of the static gain matrix of the plant model is utilized to identify the most relevant control channels and is combined with the dynamic response of system around a given operating trajectory to design the feedback controller. A general framework for real-time feedforward + feedback control of magnetic and

  3. Discharge current modes of high power impulse magnetron sputtering

    Directory of Open Access Journals (Sweden)

    Zhongzhen Wu

    2015-09-01

    Full Text Available Based on the production and disappearance of ions and electrons in the high power impulse magnetron sputtering plasma near the target, the expression of the discharge current is derived. Depending on the slope, six possible modes are deduced for the discharge current and the feasibility of each mode is discussed. The discharge parameters and target properties are simplified into the discharge voltage, sputtering yield, and ionization energy which mainly affect the discharge plasma. The relationship between these factors and the discharge current modes is also investigated.

  4. Plasma diagnostics discharge parameters and chemistry

    CERN Document Server

    Auciello, Orlando

    1989-01-01

    Plasma Diagnostics, Volume 1: Discharge Parameters and Chemistry covers seven chapters on the important diagnostic techniques for plasmas and details their use in particular applications. The book discusses optical diagnostic techniques for low pressure plasmas and plasma processing; plasma diagnostics for electrical discharge light sources; as well as Langmuir probes. The text also describes the mass spectroscopy of plasmas, microwave diagnostics, paramagnetic resonance diagnostics, and diagnostics in thermal plasma processing. Electrical engineers, nuclear engineers, microwave engineers, che

  5. On current termination in rotamak discharges

    Energy Technology Data Exchange (ETDEWEB)

    Donaldson, N.; Euripides, P.; Jones, I.R.; Xu, S. [Flinders Univ. of South Australia, Bedford Park, SA (Australia). School of Physical Sciences

    1995-03-01

    A new series of rotamak experiments conducted in a 50 litre spherical pyrex discharge vessel is described. An analysis of the results, together with that of previous results from a smaller, 10 litre vessel, provides an explanation for the current termination phenomenon which is such a noteworthy and characteristic feature of all rotamak discharges studied to date. It is shown that the amplitude of the applied rotating magnetic field, B{sub {omega}}, has to be greater than a certain critical value, B{sub {omega}}{sup crit}, for the rotamak discharge to be maintained. Provided B{sub {omega}} {>=} B{sub {omega}}{sup crit}, the properties of the discharge are then determined by the behaviour of the circuit used to couple the RF generators to the plasma load. The conditions necessary for the production of a compact toroidal magnetic configuration are presented. (author).

  6. Resistive evolution of current profile in tokamaks, application to the optimization of Tore-supra plasma discharges; Evolution resistive du profil de courant dans les Tokamaks, application a l'optimisation des decharges de Tore Supra

    Energy Technology Data Exchange (ETDEWEB)

    Bregeon, R

    1999-03-01

    In Tokamak plasma physics, current profile shaping has now become a key issue to improve the confinement properties of the plasma discharge. The objective of this work is to study the processes governing the current diffusion when non-inductive current are playing a major role in the discharge. Ultimately, this study aims to identify the key parameters to control the plasma current density profile with external current drive heating systems such as Lower Hybrid Current drive (LHCD) or self generated current drive such as the bootstrap current. Principles of non inductive current drive and heating systems are introduced as well as bootstrap current mechanisms. Then we present the experimental study of plasma parallel electric conductivity to validate existing models. Using these results, the poloidal magnetic field flux diffusion is modelled, using toroidal co-ordinates in order to give an accurate description of the current density profiles evolution. The initial and boundary conditions required for numerical resolution of the diffusion equation are also presented. Finally, we conclude this work with the simulations of two discharges: one with Fast Wave Electron Heating and the second using Lower Hybrid Current Drive. These simulations have multiples aims: validity test of our numerical tool and to show some limits of cylindrical models. Test of electric conductivity and bootstrap current models. To identify the key parameters involved in the current diffusion processes of a high performance plasma discharge on Tore Supra. Such simulations are crucial to determine the amount of non-inductive current required to control and sustain long plasma discharges in steady state. (author)

  7. Plasma discharge self-cleaning filtration system

    Science.gov (United States)

    Cho, Young I.; Fridman, Alexander; Gutsol, Alexander F.; Yang, Yong

    2014-07-22

    The present invention is directed to a novel method for cleaning a filter surface using a plasma discharge self-cleaning filtration system. The method involves utilizing plasma discharges to induce short electric pulses of nanoseconds duration at high voltages. These electrical pulses generate strong Shockwaves that disintegrate and dislodge particulate matter located on the surface of the filter.

  8. Beam--plasma instabilities and the beam--plasma discharge

    Energy Technology Data Exchange (ETDEWEB)

    Kellogg, P.J.; Boswell, R.W.

    1986-05-01

    Using a new electron gun, a number of measurements bearing on the generation of beam--plasma discharge (BPD) in WOMBAT (waves on magnetized beams and turbulence) (R. W. Boswell and P. J. Kellogg, Geophys. Res. Lett. 10, 565 (1983)) have been made. A beam--plasma discharge is an rf discharge in which the rf fields are provided by instabilities (W. D. Getty and L. D. Smullin, J. Appl. Phys. 34, 3421 (1963)). The new gun has a narrower divergence angle than the old, and comparison of the BPD thresholds for the two guns verifies that the BPD ignition current is proportional to the cross-sectional area of the plasma. The high-frequency instabilities, precursors to the BPD, are identified with the two Trivelpiece--Gould modes (A. W. Trivelpiece and R. W. Gould, J. Appl. Phys. 30, 1784 (1959)). Which frequency appears depends on the neutral pressure. The measured frequencies are not consistent with the simple interpretation of the lower frequency as a Cerenkov resonance with the low-Trivelpiece--Gould mode; it must be a cyclotron resonance. As is generally true in such beam--plasma interaction experiments, strong low-frequency waves appear at currents far below those necessary for BPD ignition. These low-frequency waves are shown to control the onset of the high-frequency precursors to the BPD. A mechanism for this control is suggested, which involves the conversion of a convective instability to an absolute one by trapping of the unstable waves in the density perturbations of the low-frequency waves. This process greatly reduces the current necessary for BPD ignition.

  9. Current-Induced Membrane Discharge

    DEFF Research Database (Denmark)

    Andersen, Mathias Bækbo; van Soestbergen, M.; Mani, A.

    2012-01-01

    . Salt depletion leads to a large electric field resulting in a local pH shift within the membrane with the effect that the membrane discharges and loses its ion selectivity. Since salt co-ions, H+ ions, and OH- ions contribute to OLC, CIMD interferes with electrodialysis (salt counterion removal...

  10. Hybrid Modeling of Plasma Discharges

    Science.gov (United States)

    2010-04-01

    or near-term future computational capabilities; this is why most kinetic solvers are limited to 2D- 2V or 2D-3V configurations and for a single or...near the X-point, as found in solar and geo-plasma or in high temperature field reversed configurations (FRC). The latter may require a dynamic...sinusoidal perturbation (see top-left panel in Figure 30). This allowed us to immediately trigger transverse instabilities, which developed into a

  11. Thermal analysis of high pressure micro plasma discharge

    Science.gov (United States)

    Mobli, Mostafa

    resistor and capacitance. A detailed gas phase chemical kinetic model was also implemented. One-dimensional simulation has been performed to study the effects of the neutral gas temperature on a micro plasma discharge operating in the "abnormal" glow mode. In addition, two dimensional simulation has been conducted to simulate the "normal" glow regime of a micro plasma discharge that has multi-dimensional spatial dependence. The effects of conjugate heat transfer on the gas temperature distribution and the overall plasma characteristics i.e. the voltage-current curve and electron number density has been investigated. The conjugate heat transfer is found to significantly affect the plasma behavior. Finally a temporally varying temperature boundary condition has been proposed that reduces the computational overhead but resolves the conjugate heat transfer effect with reasonable accuracy.

  12. Early Stage of Pulsed High Current Discharge with Copper Powder

    Science.gov (United States)

    Yokoyama, Takuma; Kuraoka, Takuya; Takano, Kazuya; Ibuka, Shinji; Yasuoka, Koichi; Ishii, Shozo

    Early phase of powder plasmas powered by a pulsed high current discharge was examined by use of high-speed cameras and a laser shadowgraph and schlieren techniques. Initial electrons created by a pre-ionization discharge collide with both an anode and powder particles, of which surfaces evaporate after then. Evaporation of the particle by electron collision initially occured in the hemisphere surface which is close to cathode side. Since vaporization of the anode far exceeds that of the particles, discharge characteristics is almost similar to that of vacuum sparks in which expanding anode plasmas are observed. In order to suppress the developpment of the anode plasma, reduction of the effective anode area by varying the anode shape was examined.

  13. Exploration to generate atmospheric pressure glow discharge plasma in air

    Science.gov (United States)

    Wenzheng, LIU; Chuanlong, MA; Shuai, ZHAO; Xiaozhong, CHEN; Tahan, WANG; Luxiang, ZHAO; Zhiyi, LI; Jiangqi, NIU; Liying, ZHU; Maolin, CHAI

    2018-03-01

    Atmospheric pressure glow discharge (APGD) plasma in air has high application value. In this paper, the methods of generating APGD plasma in air are discussed, and the characteristics of dielectric barrier discharge (DBD) in non-uniform electric field are studied. It makes sure that APGD in air is formed by DBD in alternating current electric field with using the absorbing electron capacity of electret materials to provide initial electrons and to end the discharge progress. Through designing electric field to form two-dimensional space varying electric field and three-dimensional space varying electric field, the development of electron avalanches in air-gap is suppressed effectively and a large space of APGD plasma in air is generated. Further, through combining electrode structures, a large area of APGD plasma in air is generated. On the other hand, by using the method of increasing the density of initial electrons, millimeter-gap glow discharge in atmospheric pressure air is formed, and a maximum gap distance between electrodes is 8 mm. By using the APGD plasma surface treatment device composed of contact electrodes, the surface modification of high polymer materials such as aramid fiber and polyester are studied and good effect of modifications is obtained. The present paper provides references for the researchers of industrial applications of plasma.

  14. Real-time control for long ohmic alternate current discharges

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Ivo S., E-mail: ivoc@ipfn.ist.utl.pt; Duarte, Paulo; Fernandes, Horácio; Valcárcel, Daniel F.; Carvalho, Pedro J.; Silva, Carlos; Duarte, André S.; Neto, André; Sousa, Jorge; Batista, António J.N.; Hekkert, Tiago; Carvalho, Bernardo B.; Gomes, Rui B.

    2014-05-15

    Highlights: • 40 Alternate plasma current (AC) semi-cycles without loss of ionization, more than 1 s of operation. • AC discharges automatic control: feedback loops, time-windows control strategy, goal oriented time-windows and exception handling. • Energy deposition and Carbon radiation evolution during the AC discharges. - Abstract: The ISTTOK tokamak has a long tradition on alternate plasma current (AC) discharges, but the old control system was limiting and lacked full system integration. In order to improve the AC discharges performance the ISTTOK fast control system was updated. This control system developed on site based on the Advanced Telecommunications Computing Architecture (ATCA) standard now integrates the information gathered by all the tokamak real-time diagnostics to produce an accurate observation of the plasma parameters. The real-time actuators were also integrated, allowing a Multiple Input Multiple Output (MIMO) control environment with several synchronization strategies available. The control system software was developed in C++ on top of a Linux system with the Multi-threaded Application Real-Time executor (MARTe) Framework to synchronize the real-time code execution under a 100μs control cycle. In addition, to simplify the discharge programming, a visual Human–Machine Interface (HMI) was also developed using the BaseLib2 libraries included in the MARTe Framework. This paper presents the ISTTOK control system and the optimizations that extended the AC current discharges duration to more than 1 s, corresponding to 40 semi-cycles without apparent degradation of the plasma parameters. This upgrade allows ISTTOK to be used as a low-cost material testing facility with long time exposures to nuclear fusion relevant plasmas, comparable (in duration) with medium size tokamaks.

  15. Discharge current distribution in stratified soil under impulse discharge

    Science.gov (United States)

    Eniola Fajingbesi, Fawwaz; Shahida Midi, Nur; Elsheikh, Elsheikh M. A.; Hajar Yusoff, Siti

    2017-06-01

    The mobility of charge particles traversing a material defines its electrical properties. Soil (earth) have long been the universal grounding before and after the inception of active ground systems for electrical appliance purpose due to it semi-conductive properties. The soil can thus be modelled as a single material exhibiting semi-complex inductive-reactive impedance. Under impulse discharge such as lightning strikes to soil this property of soil could result in electric potential level fluctuation ranging from ground potential rise/fall to electromagnetic pulse coupling that could ultimately fail connected electrical appliance. In this work we have experimentally model the soil and lightning discharge using point to plane electrode setup to observe the current distribution characteristics at different soil conductivity [mS/m] range. The result presented from this research indicate above 5% shift in conductivity before and after discharge which is significant for consideration when dealing with grounding designs. The current distribution in soil have also be successfully observed and analysed from experimental result using mean current magnitude in relation to electrode distance and location, current density variation with depth all showing strong correlation with theoretical assumptions of a semi-complex impedance material.

  16. Three-fluid magnetohydrodynamical simulation of plasma focus discharges

    Energy Technology Data Exchange (ETDEWEB)

    Behler, K.; Bruhns, H.

    1987-12-01

    A two-dimensional, three-fluid code based on the two-fluid Potter code (Methods in Computational Physics (Academic, New York, 1970), Vol. 9, p. 340) was developed for simulating the plasma focus discharge. With this code it is possible to treat the neutral gas in addition to the plasma components and to model the ionization and recombination phenomena. Thus the sheet dynamics in a plasma focus can be studied and effects investigated such as the occurrence of residual gas (or plasma) density behind the current sheet in the run-down phase. This is a prerequisite to the occurrence of leak currents, which are one of the causes limiting the performance of large plasma focus devices. It is shown that fast operating foci with small dimensions behave favorably compared with the ''classical'' Mather focus (Methods of Experimental Physics (Academic, New York, 1971), Vol. 9B, p. 187) with long coaxial electrodes.

  17. Battling Bacterial Biofilms with Gas Discharge Plasma

    Science.gov (United States)

    Zelaya, Anna; Vandervoort, Kurt; Brelles-Mariño, Graciela

    Most studies dealing with growth and physiology of bacteria have been carried out using free-living cells. However, most bacteria live in communities referred to as biofilms where cooperative interactions among their members make conventional methods of controlling microbial growth often ineffective. The use of gas discharge plasmas represents an alternative to traditional decontamination/sterilization methods. We studied biofilms using two organisms, Chromobacterium violaceum and Pseudomonas aeruginosa. With the first organism we demonstrated almost complete loss of cell culturability after a 5-min plasma treatment. However, additional determinations showed that non-culturable cells were still alive after short exposure times. We have recently reported the effect of plasma on P. aeruginosa biofilms grown on borosilicate coupons. In this paper, we present results for plasma treatments of 1-, 3-, and 7-day old P. aeruginosa biofilms grown on polycarbonate or stainless-steel coupons. Results indicate nearly 100% of ­biofilm inactivation after 5 min of exposure with similar inactivation kinetics for 1-, 3-, and 7-day-old biofilms, and for both materials used. The inactivation kinetics is similar for both organisms, suggesting that the method is useful regardless of the type of biofilm. AFM images show changes in biofilm structure for various plasma exposure times.

  18. [Automatic adjustment control system for DC glow discharge plasma source].

    Science.gov (United States)

    Wan, Zhen-zhen; Wang, Yong-qing; Li, Xiao-jia; Wang, Hai-zhou; Shi, Ning

    2011-03-01

    There are three important parameters in the DC glow discharge process, the discharge current, discharge voltage and argon pressure in discharge source. These parameters influence each other during glow discharge process. This paper presents an automatic control system for DC glow discharge plasma source. This system collects and controls discharge voltage automatically by adjusting discharge source pressure while the discharge current is constant in the glow discharge process. The design concept, circuit principle and control program of this automatic control system are described. The accuracy is improved by this automatic control system with the method of reducing the complex operations and manual control errors. This system enhances the control accuracy of glow discharge voltage, and reduces the time to reach discharge voltage stability. The glow discharge voltage stability test results with automatic control system are provided as well, the accuracy with automatic control system is better than 1% FS which is improved from 4% FS by manual control. Time to reach discharge voltage stability has been shortened to within 30 s by automatic control from more than 90 s by manual control. Standard samples like middle-low alloy steel and tin bronze have been tested by this automatic control system. The concentration analysis precision has been significantly improved. The RSDs of all the test result are better than 3.5%. In middle-low alloy steel standard sample, the RSD range of concentration test result of Ti, Co and Mn elements is reduced from 3.0%-4.3% by manual control to 1.7%-2.4% by automatic control, and that for S and Mo is also reduced from 5.2%-5.9% to 3.3%-3.5%. In tin bronze standard sample, the RSD range of Sn, Zn and Al elements is reduced from 2.6%-4.4% to 1.0%-2.4%, and that for Si, Ni and Fe is reduced from 6.6%-13.9% to 2.6%-3.5%. The test data is also shown in this paper.

  19. ORAL ISSUE OF THE JOURNAL "USPEKHI FIZICHESKIKH NAUK": Modeling of gas discharge plasma

    Science.gov (United States)

    Smirnov, Boris M.

    2009-06-01

    The condition for the self-maintenance of a gas discharge plasma (GDP) is derived from its ionization balance expressed in the Townsend form and may be used as a definition of a gas discharge plasma in its simplest form. The simple example of a gas discharge plasma in the positive column of a cylindrical discharge tube allows demonstrating a wide variety of possible GDP regimes, revealing a contradiction between simple models used to explain gas discharge regimes and the large number of real processes responsible for the self-maintenance of GDP. The variety of GDP processes also results in a stepwise change of plasma parameters and developing some instabilities as the voltage or discharge current is varied. As a consequence, new forms and new applications of gas discharge arise as technology progresses.

  20. Dielectric barrier discharge plasma treatment of cellulose nanofibre surfaces

    DEFF Research Database (Denmark)

    Kusano, Yukihiro; Madsen, Bo; Berglund, Linn

    2017-01-01

    Dielectric barrier discharge plasma treatment was applied to modify cellulose nanofibre (CNF) surfaces with and without ultrasonic irradiation. The plasma treatment improved the wetting by deionised water and glycerol, and increased the contents of oxygen, carbonyl group, and carboxyl group...

  1. Role of Plasma Discharge in Division of Prostatic Tissue

    Science.gov (United States)

    Ward, Arlen; Almgren, Carl; Yu, Zeng-Qi; Sartor, Joe; Collins, George

    2009-10-01

    During the treatment of benign prostatic hyperplasia electrical energy is used to separate prostatic tissue and remove it as a urinary obstruction. This surgical procedure is often performed in a saline environment, and current paths change as the tissue and fluid are heated. This study shows that a plasma discharge at the electrode is necessary to provide the current densities necessary to vaporize portions of the prostatic tissue in order to facilitate removal. This behavior is predicted in finite element simulations, and verified with color schlieren imaging and ex vivo bovine prostate tests.

  2. Characterization of ultra-short pulsed discharge plasma for CVD processing. [Chemical Vapor Deposition

    Energy Technology Data Exchange (ETDEWEB)

    Mizuno, Akira (Toyohashi Univ. of Technology (Japan). Dept. of Ecological Engineering); Okazaki, Ken (Tokyo Inst. of Technology (Japan). Research Center for Carbon Recycling and Utilization); Takekoshi, Takashi (Mitsubishi Kasei Co., Okayama (Japan). Mizushima Works); Tobe, Ryoki (Anelva Corp., Tokyo (Japan). Research Development Center)

    Characteristics of pulsed discharge plasma of methane-hydrogen gas mixture and Ar gas have been studied for active control of plasma chemical vapor deposition (CVD) processing. Voltage-current characteristics, time-lag of the current pulse, and the photon emission intensity profile have been investigated using high-voltage pulses of 50-1000 ns duration. In such a pulse discharge, voltages much higher than those in a dc glow discharge can be applied without any plasma nonuniformity or arcing because voltage amplitude falls to zero before glow to arc transition. A current value of more than 10[sup 3] times those in a glow discharge can be established. Very high photon emission intensity from CH radicals and H ions have been observed near the anode in a pulsed plasma. This is different in dc plasma, where the negative glow region near the cathode is the brightest.

  3. Parameters of the plasma of a dc pulsating discharge in a supersonic air flow

    Energy Technology Data Exchange (ETDEWEB)

    Shibkov, V. M., E-mail: shibkov@phys.msu.ru; Shibkova, L. V.; Logunov, A. A. [Moscow State University, Faculty of Physics (Russian Federation)

    2017-03-15

    A dc discharge in a cold (T = 200 K) supersonic air flow at a static pressure of 200–400 Torr was studied experimentally. The excited unsteady pulsating discharge has the form of a thin plasma channel with a diameter of ≤1 mm, stretched downstream the flow. Depending on the discharge current, the pulsation frequency varies from 800 to 1600 Hz and the electron temperature varies from 8000 to 15000 K.

  4. Characteristics of plasma properties in double discharge ablative pulsed plasma thrusters

    Science.gov (United States)

    Wu, Zhiwen; Sun, Guorui; Liu, Zhen; Liu, Xiangyang; Xie, Kan; Wang, Ningfei

    2017-11-01

    Ablative pulsed plasma thrusters, the earliest electric space propulsion devices, create highly transient plasmas in short discharges that are expelled to create thrust. In recent years, the double-discharge ablative pulsed plasma thruster design has been proposed to improve the low-thrust efficiency. In this study, optical emission spectroscopy was applied to investigate the plasma properties in different regions and energy distributions. The electron temperature and electron density of the plasmas are derived and discussed. This study provides a physical mechanism for double-discharge pulsed plasma thrusters.

  5. Sustained diffusive alternating current gliding arc discharge in atmospheric pressure air

    DEFF Research Database (Denmark)

    Zhu, Jiajian; Gao, Jinlong; Li, Zhongshan

    2014-01-01

    Rapid transition from glow discharge to thermal arc has been a common problem in generating stable high-power non-thermal plasmas especially at ambient conditions. A sustained diffusive gliding arc discharge was generated in a large volume in atmospheric pressure air, driven by an alternating...... current (AC) power source. The plasma column extended beyond the water-cooled stainless steel electrodes and was stabilized by matching the flow speed of the turbulent air jet with the rated output power. Comprehensive investigations were performed using high-speed movies measured over the plasma column......, synchronized with simultaneously recorded current and voltage waveforms. Dynamic details of the novel non-equilibrium discharge are revealed, which is characterized by a sinusoidal current waveform with amplitude stabilized at around 200 mA intermediate between thermal arc and glow discharge, shedding light...

  6. Influence of plasma properties on ARC discharge destabilization

    Science.gov (United States)

    Podenok, L. P.; Sharakhovskii, L. I.; Shimanovich, V. D.; Yas'ko, O. I.

    1997-01-01

    The influence of heat transfer processes in arc discharges on the development of thermal instability is considered. A substantial dependence of the process of destabilization on the plasma properties is shown by the example of argon and helium arcs.

  7. Abrupt changes in neon discharge plasma detected via the optogalvanic effect

    Energy Technology Data Exchange (ETDEWEB)

    Han, Xianming L., E-mail: xhan@butler.edu [Dept. of Physics and Astronomy, Butler University, Indianapolis, IN 46208 (United States); Blosser, Michael C. [Dept. of Physics and Astronomy, Butler University, Indianapolis, IN 46208 (United States); Misra, Prabhakar [Dept. of Physics and Astronomy, Howard University, Washington DC 20059 (United States); Chandran, Haridass [Dept. of Physical Science, Belfry School, Belfry, KY 41514 (United States)

    2012-10-30

    When a laser is tuned between two excited energy levels of a gas in a Direct Current discharge lamp, the discharge current will experience a temporary disturbance lasting tens or hundreds of microseconds known as the optogalvanic effect. We have carried out extensive studies of optogalvanic effects in neon discharge plasmas for transitions at 621.7 nm, 630.5 nm, 638.3 nm, 650.7 nm and 659.9 nm. A nonlinear least-squares Monte Carlo technique has been used to determine the relevant amplitude coefficients, decay rates and the instrumental time constant. We discovered an abrupt change in the neon discharge plasma at a discharge current of about 6 mA.

  8. Wave phenomena preceding and during a beam-plasma discharge

    Energy Technology Data Exchange (ETDEWEB)

    Boswell, R.W.; Morey, I.J.; Porteous, R.K. (Australian National Univ., Canberra, Australian Capital Territory (Australia))

    1989-03-01

    The waves and associated phenomena which are generated prior to and during the beam-plasma discharge (BPD) in the waves on magnetized beams and turbulence (WOMBAT) apparatus are described. These range in frequency from below the ion gyrofrequency of a few kilohertz to strong harmonics of the electron plasma frequency above 1 GHz. The low-frequency ion waves appear to be driven by E {times} B forces arising from the nonneutrality of the electron beam-plasma column at low beam currents (I{sub b}) or low gas pressures (P). As I{sub b} increases, the motion becomes chaotic after a sequence of wave period doublings resulting in the generation of subharmonies. Windows of coherent motion are observed within the chaotic regions. Further increases in I{sub b} lead to increases in ionizing collisions and when the background plasma density becomes sufficiently high, waves around the electron plasma frequency can be generated. Initially, these waves are modulated by the gross density perturbations of the large-amplitude ion waves, but subsequently they also increase to large amplitudes: e{phi}/kT {approximately} 1. This is sufficient to accelerate the background electrons to ionizing energies and produce the BPD. At low pressures this occurs for f{sub pe}/f{sub ce} {approximately} 0.5 (BPD1) with the process occurring in short bursts ({approximately} 100{tau}{sub pe}). Increasing I{sub b} produces a sudden jump in the frequency to {approximately} 1.5 f{sub ce} and a further increase in the plasma density and luminosity, which the authors term BPD2.

  9. Optical observations of post-discharge phenomena of laser-triggered discharge produced plasma for EUV lithography

    Science.gov (United States)

    Lim, Soowon; Kitajima, Seiya; Lu, Peng; Sakugawa, Takashi; Akiyama, Hidenori; Katsuki, Sunao; Teramoto, Yusuke

    2015-01-01

    This paper reports the dynamic post-discharge phenomena of laser-triggered discharge-produced plasmas (LTDPP) for extreme ultraviolet lithography (EUVL) sources. A pulsed laser was focused on the high-voltage tin cathode surface to form tin vapor jet across a 5 mm long anode-cathode gap, which leads to the electrical breakdown. The post-discharge phenomena were observed using both of the Schlieren method and high-speed camera. Schlieren images show the dynamic evolution of the discharge plasma and the development of tin droplets. Visible emission from the plasma lasted for more than 1 µs after the current stopped. The droplets emerged from the cathode approximately 100 µs after discharge and spread throughout the electrodes gap. Various sizes of droplets stagnate in the gap for milliseconds. The subsequent laser pulse and voltage application show an interaction between the droplets and the subsequent discharge. The subsequent laser pulse evaporates not only the cathode surface but also the droplets, which influence the tin vapor distribution in the gap. This uncertain vapor distribution affects the formation process of microplasmas that emit EUV.

  10. Plasma ionization frequency, edge-to-axis density ratio, and density on axis of a cylindrical gas discharge

    Energy Technology Data Exchange (ETDEWEB)

    Palacio Mizrahi, J. H. [Physics Department, Technion, Haifa 32000 (Israel)

    2014-06-15

    A rigorous derivation of expressions, starting from the governing equations, for the ionization frequency, edge-to-axis ratio of plasma density, plasma density at the axis, and radially averaged plasma density in a cylindrical gas discharge has been obtained. The derived expressions are simple and involve the relevant parameters of the discharge: Cylinder radius, axial current, and neutral gas pressure. The found expressions account for ion inertia, ion temperature, and changes in plasma ion collisionality.

  11. Process Performances of 2 ns Pulsed Discharge Plasma

    Science.gov (United States)

    Matsumoto, Takao; Wang, Douyan; Namihira, Takao; Akiyama, Hidenori

    2011-08-01

    Pulsed discharge plasmas have been used to treat exhaust gases. Since pulse duration and the rise time of applied voltage to the discharge electrode has a strong influence on the energy efficiency of pollutant removal, the development of a short-pulse generator is of paramount importance for practical applications. In this work, it is demonstrated that the non thermal plasma produced by the 2 ns pulsed discharge has a higher energy efficiency than the 5 ns pulsed discharge plasma for NO removal and ozone generation. Typically, the NO removal efficiency was 1.0 mol kW-1 h-1 for 70% NO removal (initial NO concentration = 200 ppm, gas flow = 10 L/min). Meanwhile, the ozone yield was 500 g kW-1 h-1 for 20 g/m3 ozone concentration in the case of oxygen feeding. These energy efficiencies are the highest in the literature.

  12. Development of a discharge-heated plasma tube

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Byung Heon; Jin, J. T.; Nam, S. M.; Lee, S. M.; Choi, H. L.; Ko, D. K.; Kim, S. H.; Lee, Y. B.; Choi, Y. S.; Lee, J. M.; Lee, C. K.; Lee, H. G.; Lee, H. C.; Jung, S. M.; Kim, Y. J.; Choi, G. S.; Son, N. G

    1999-12-01

    A discharge-heated type plasma tube was designed and constructed. The structure of the laser plasma tube was designed to be easy in maintenance. The inside plasma tube was made of a high purity alumina and the thermal insulator tube was made of a porous alumina. The electrode made of tungsten was chosen for the endurance of high discharge voltage. AR coated windows were used as laser windows. A proto-type laser plasma tube was tested with a pulse modulator. An average laser output power was 32 W at the discharge voltage of 28 kV, the electric input power of 4.6 kW, and the pulse repetition rates of 10 kHz. (author)

  13. High-frequency underwater plasma discharge application in antibacterial activity

    Science.gov (United States)

    Ahmed, M. W.; Choi, S.; Lyakhov, K.; Shaislamov, U.; Mongre, R. K.; Jeong, D. K.; Suresh, R.; Lee, H. J.

    2017-03-01

    Plasma discharge is a novel disinfection and effectual inactivation approach to treat microorganisms in aqueous systems. Inactivation of Gram-negative Escherichia coli ( E. coli) by generating high-frequency, high-voltage, oxygen (O2) injected and hydrogen peroxide (H2O2) added discharge in water was achieved. The effect of H2O2 dose and oxygen injection rate on electrical characteristics of discharge and E. coli disinfection has been reported. Microbial log reduction dependent on H2O2 addition with O2 injection was observed. The time variation of the inactivation efficiency quantified by the log reduction of the initial E. coli population on the basis of optical density measurement was reported. The analysis of emission spectrum recorded after discharge occurrence illustrated the formation of oxidant species (OH•, H, and O). Interestingly, the results demonstrated that O2 injected and H2O2 added, underwater plasma discharge had fabulous impact on the E. coli sterilization. The oxygen injection notably reduced the voltage needed for generating breakdown in flowing water and escalated the power of discharge pulses. No impact of hydrogen peroxide addition on breakdown voltage was observed. A significant role of oxidant species in bacterial inactivation also has been identified. Furthermore the E. coli survivability in plasma treated water with oxygen injection and hydrogen peroxide addition drastically reduced to zero. The time course study also showed that the retardant effect on E. coli colony multiplication in plasma treated water was favorable, observed after long time. High-frequency underwater plasma discharge based biological applications is technically relevant and would act as baseline data for the development of novel antibacterial processing strategies.

  14. High-frequency underwater plasma discharge application in antibacterial activity

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, M. W.; Choi, S.; Lyakhov, K.; Shaislamov, U. [Jeju National University, Department of Nuclear and Energy Engineering (Korea, Republic of); Mongre, R. K.; Jeong, D. K. [Jeju National University, Faculty of Biotechnology (Korea, Republic of); Suresh, R.; Lee, H. J., E-mail: hjlee@jejunu.ac.kr [Jeju National University, Department of Nuclear and Energy Engineering (Korea, Republic of)

    2017-03-15

    Plasma discharge is a novel disinfection and effectual inactivation approach to treat microorganisms in aqueous systems. Inactivation of Gram-negative Escherichia coli (E. coli) by generating high-frequency, high-voltage, oxygen (O{sub 2}) injected and hydrogen peroxide (H{sub 2}O{sub 2}) added discharge in water was achieved. The effect of H{sub 2}O{sub 2} dose and oxygen injection rate on electrical characteristics of discharge and E. coli disinfection has been reported. Microbial log reduction dependent on H{sub 2}O{sub 2} addition with O{sub 2} injection was observed. The time variation of the inactivation efficiency quantified by the log reduction of the initial E. coli population on the basis of optical density measurement was reported. The analysis of emission spectrum recorded after discharge occurrence illustrated the formation of oxidant species (OH{sup •}, H, and O). Interestingly, the results demonstrated that O{sub 2} injected and H{sub 2}O{sub 2} added, underwater plasma discharge had fabulous impact on the E. coli sterilization. The oxygen injection notably reduced the voltage needed for generating breakdown in flowing water and escalated the power of discharge pulses. No impact of hydrogen peroxide addition on breakdown voltage was observed. A significant role of oxidant species in bacterial inactivation also has been identified. Furthermore the E. coli survivability in plasma treated water with oxygen injection and hydrogen peroxide addition drastically reduced to zero. The time course study also showed that the retardant effect on E. coli colony multiplication in plasma treated water was favorable, observed after long time. High-frequency underwater plasma discharge based biological applications is technically relevant and would act as baseline data for the development of novel antibacterial processing strategies.

  15. Characteristics of 2-heptanone decomposition using nanosecond pulsed discharge plasma

    Science.gov (United States)

    Nakase, Yuki; Fukuchi, Yuichi; Wang, Douyan; Namihira, Takao; Akiyama, Hidenori; Kumamoto University Collaboration

    2015-09-01

    Volatile organic compounds (VOC) evaporate at room temperature. VOCs typically consist of toluene, benzene and ethyl acetate, which are used in cosmetics, dry cleaning products and paints. Exposure to elevated levels of VOCs may cause headaches, dizziness and irritation to the eyes, nose, and throat; they may also cause environmental problems such as air pollution, acid rain and photochemical smog. As such, they require prompt removal. Nanosecond pulsed discharge is a kind of non-thermal plasma consisting of a streamer discharge. Several advantages of nanosecond pulsed discharge plasma have been demonstrated by studies of our research group, including low heat loss, highly energetic electron generation, and the production of highly active radicals. These advantages have shown ns pulsed discharge plasma capable of higher energy efficiency for processes, such as air purification, wastewater treatment and ozone generation. In this research, nanosecond pulsed discharge plasma was employed to treat 2-heptanone, which is a volatile organic compound type and presents several harmful effects. Characteristics of treatment dependent on applied voltage, gas flow rate and input energy density were investigated. Furthermore, byproducts generated by treatment were also investigated.

  16. Sterilization by negative and positive DC plasma with a micro discharge gap at atmospheric pressure

    Science.gov (United States)

    Li, Hua; Jiang, Lin-Xiu; Jiang, Yong-Rong; Zhu, Jian-Min; Chen, Zhen-Cheng

    2017-11-01

    A new needle-to-droplet electrode structure with a micro discharge gap (2 mm) was designed to achieve direct current (DC) discharge plasma in ambient air with the aim of using the plasma to sterilize liquids. Without using noble gases or an external air flow, we succeeded in generating both a negative and positive DC plasma at atmospheric pressure. The plasma was driven by a 0 to ‑20,000 V, 100 W DC power supply. A stainless steel needle with a tip diameter of ˜ 50μm and a 200-μL droplet of bacteria-containing liquid served as the electrodes. At atmospheric pressure and room temperature (23∘C), utilizing the negative DC plasma, the discharge time lasted 10 s; the results showed that the higher the discharge voltage, the more efficient the sterilization effect. Conversely, when we applied a voltage of ‑5.5 kV, we found that the sterilization effect was more efficient for longer discharge times. Our findings demonstrate that Escherichia coli (E. coli) and Bacillus subtilis (B. subtilis) can be killed in about 30 s. Our experiments show that our sterilization method required less time and was more efficient for positive than for negative DC plasma under the same conditions.

  17. Effects of Gas Flow Rate on the Discharge Characteristics of a DC Excited Plasma Jet

    Science.gov (United States)

    Li, Xuechen; Jia, Pengying; Di, Cong; Bao, Wenting; Zhang, Chunyan

    2015-09-01

    A direct current (DC) source excited plasma jet consisting of a hollow needle anode and a plate cathode has been developed to form a diffuse discharge plume in ambient air with flowing argon as the working gas. Using optical and electrical methods, the discharge characteristics are investigated for the diffuse plasma plume. Results indicate that the discharge has a pulse characteristic, under the excitation of a DC voltage. The discharge pulse corresponds to the propagation process of a plasma bullet travelling from the anode to the cathode. It is found that, with an increment of the gas flow rate, both the discharge plume length and the current peak value of the pulsed discharge decrease in the laminar flow mode, reach their minima at about 1.5 L/min, and then slightly increase in the turbulent mode. However, the frequency of the pulsed discharge increases in the laminar mode with increasing the argon flow rate until the argon flow rate equals to about 1.5 L/min, and then slightly decreases in the turbulent mode. supported by National Natural Science Foundation of China (Nos. 10805013, 11375051), Funds for Distinguished Young Scientists of Hebei Province, China (No. A2012201045), Department of Education for Outstanding Youth Project of China (No. Y2011120), and Youth Project of Hebei University of China (No. 2011Q14)

  18. CO2 Dissociation by Low Current Gliding Discharge in the Reverse Vortex Flow

    Science.gov (United States)

    Gutsol, Alexander

    2012-10-01

    If performed with high energy efficiency, plasma-chemical dissociation of carbon dioxide can be a way of converting and storing energy when there is an excess of electric energy, for example generated by solar elements of wind turbines. CO2 dissociation with efficiency of up to 90% was reported earlier for low pressure microwave discharge in supersonic flow. A new plasma-chemical system uses a low current gliding discharge in the reverse vortex flow of plasma gas. The system is a development of the Gliding Arc in Tornado reactor. The system was used to study dissociation of CO2 in wide ranges of the following experimental parameters: reactor pressure (15-150 kPa), discharge current (50-500 mA), gas flow rate (3-30 liters per minute), and electrode gap length (1-10 cm). Additionally, the effect of thermal energy recuperation on CO2 dissociation efficiency was tested. Plasma chemical efficiency of CO2 dissociation is very low (about 3%) in a short discharge at low pressures (about 15 kPa) when it is defined by electronic excitation. The highest efficiency (above 40%) was reached at pressures 50-70 kPa in a long discharge with thermal energy recuperation. It means that the process is controlled by thermal dissociation with subsequent effective quenching. Plasma chemical efficiency was determined from the data of chromatographic analysis and oscilloscope electric power integration, and also was checked calorimetrically by the thermal balance of the system.

  19. Formation of a spark discharge in an inhomogeneous electric field with current limitation by a large ballast Resistance

    Energy Technology Data Exchange (ETDEWEB)

    Baldanov, B. B., E-mail: baibat@mail.ru [Russian Academy of Sciences, Institute of Physical Material Science, Siberian Branch (Russian Federation)

    2016-01-15

    Results of studies of a spark discharge initiated in argon in a point–plane electrode gap with limitation of the discharge current by a large ballast resistance are presented. It is shown that the current flowing through the plasma channel of such a low-current spark has the form of periodic pulses. It is experimentally demonstrated that, when a low-current spark transforms into a constricted glow discharge, current pulses disappear, the spatial structure of the cathode glow changes abruptly, and a brightly glowing positive plasma column forms in the gap.

  20. Sterilization of Turmeric by Atmospheric Pressure Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Setareh, Salarieh; Davoud, Dorranian

    2013-11-01

    In this study atmospheric pressure dielectric barrier discharge (DBD) plasma has been employed for sterilizing dry turmeric powders. A 6 kV, 6 kHz frequency generator was used to generate plasma with Ar, Ar/O2, He, and He/O2 gases between the 5 mm gap of two quartz covered electrodes. The complete sterilization time of samples due to plasma treatment was measured. The most important contaminant of turmeric is bacillus subtilis. The results show that the shortest sterilization time of 15 min is achieved by exposing the samples to Ar/O2 plasma. Survival curves of samples are exponential functions of time and the addition of oxygen to plasma leads to a significant increase of the absolute value of time constant of the curves. Magnitudes of protein and DNA in treated samples were increased to a similar value for all samples. Taste, color, and solubility of samples were not changed after the plasma treatment.

  1. Thermally stimulated discharge current (TSDC) and dielectric ...

    Indian Academy of Sciences (India)

    Unknown

    2001-10-09

    Oct 9, 2001 ... current (TSDC) peak above room temperature. Hong and Day (1979) applied the techniques of thermally stimulated polarization and depolarization current for studying alkaline ion motion in glasses of sodium silicate and lead silicate. The peaks observed are discussed on the basis of d.c. conductivity and ...

  2. Thrust Stand Measurements of the Microwave Assisted Discharge Inductive Plasma Accelerator

    Science.gov (United States)

    Hallock, Ashley K.; Polzin, Kurt A.; Emsellem, Gregory D.

    2011-01-01

    Pulsed inductive plasma thrusters [1-3] are spacecraft propulsion devices in which electrical energy is capacitively stored and then discharged through an inductive coil. This type of pulsed thruster is electrodeless, with a time-varying current in the coil interacting with a plasma covering the face of the coil to induce a plasma current. Propellant is accelerated and expelled at a high exhaust velocity (O(10-100 km/s)) by the Lorentz body force arising from the interaction of the magnetic field and the induced plasma current. While this class of thruster mitigates the life-limiting issues associated with electrode erosion, pulsed inductive plasma thrusters require high pulse energies to inductively ionize propellant. The Microwave Assisted Dis- charge Inductive Plasma Accelerator (MAD-IPA), shown in Fig. 1, is a pulsed inductive plasma thruster that addressees this issue by partially ionizing propellant inside a conical inductive coil before the main current pulse via an electron cyclotron resonance (ECR) discharge. The ECR plasma is produced using microwaves and a static magnetic field from a set of permanent magnets arranged to create a thin resonance region along the inner surface of the coil, restricting plasma formation, and in turn current sheet formation, to a region where the magnetic coupling between the plasma and the theta-pinch coil is high. The use of a conical theta-pinch coil also serves to provide neutral propellant containment and plasma plume focusing that is improved relative to the more common planar geometry of the Pulsed Inductive Thruster (PIT) [1, 2]. In this paper, we describe thrust stand measurements performed to characterize the performance (specific impulse, thrust efficiency) of the MAD-IPA thruster. Impulse data are obtained at various pulse energies, mass flow rates and inductive coil geometries. Dependencies on these experimental parameters are discussed in the context of the current sheet formation and electromagnetic plasma

  3. Insulator Degradation by High Current Discharges

    Science.gov (United States)

    Engel, Thomas Gregory

    1990-08-01

    The degenerative action produced by 300 kA, repetitive arc discharges on the surface of various insulator materials is investigated as a function of insulator and electrode material and the ambient atmosphere used. The insulator damage produced by the 20 mus wide oscillating pulse is characterized by a shot-to-shot decrease in surface breakdown voltage of the insulator and a loss of insulator mass. The insulators under investigation include a broad group of ceramic, polymeric, and elastomeric materials which have been tested with graphite, molybdenum, copper, and copper-tungsten electrodes. Typically, the ambient gas used in the tests was atmospheric air although some tests were conducted in pure nitrogen, pure oxygen, and admixtures thereof. Models have also been developed which predict holdoff voltage degradation, mass erosion, and holdoff voltage conditioning for the insulator. The conditioning of an insulator is characterized by an increase in its surface holdoff voltage in the initial stages of the test. In these models, insulator performance is predicted by its HDR (i.e., holdoff voltage degradation resistance), MVC (mass vaporization coefficient), and HVC (holdoff voltage conditioning) figures of merit which are calculated using the pertinent thermophysical properties of the material. The relationship between the figures of merit is also discussed.

  4. Discharge plasmas generated by piezoelectric transformers and their applications

    Science.gov (United States)

    Itoh, H.; Teranishi, K.; Suzuki, S.

    2006-05-01

    The characteristics of discharge plasma generated by piezoelectric transformers (PTs) and the practical applications of PT-based plasma reactors are reviewed in this paper. PTs of Pb(Zr · Ti)O3 generate high voltage by the piezoelectric effect, which can cause excitation and ionization of atoms and molecules, resulting in the generation of discharge plasma. When a narrow gap exists between the PT surface and a dielectric layer having a metal back electrode, dielectric barrier discharge (DBD) occurs at atmospheric pressure and above. The mechanical vibration of the PT and the resultant surface potential, which relate to electro-mechanical energy conversion by the piezoelectric effect, are investigated using a laser Doppler vibrometer and probe method, respectively. The characteristics of DBD are examined based on light patterns detected by the intensified charge coupled device camera, and the fundamental parameters of the filamentary discharge are determined. PT-generated DBD is shown to be applicable for ozone generation and as excimer lamps, and high-power operation is demonstrated using a parallel-driven hexad plasma reactor.

  5. Characterization of Plasma Polymerized Hexamethyldisiloxane Films Prepared by Arc Discharge

    NARCIS (Netherlands)

    Lazauskas, A.; Baltrusaitis, Jonas; Grigaliunas, V.; Jucius, D; Guobiene, A.; Prosycevas, I.; Narmontas, P.

    2014-01-01

    Herein, we present a simple method for fabricating plasma polymerized hexamethyldisiloxane films (pp-HMDSO) possessing superhydrophobic characteristics via arc discharge. The pp-HMDSO films were deposited on a soda–lime–silica float glass using HMDSO monomer vapor as a precursor. A detailed surface

  6. The layered structure of the carbon arc discharge plasma

    Science.gov (United States)

    Vekselman, Vladislav; Stratton, Brentley; Raitses, Yevgeny; LaboratoryPlasma Nanosynthesis Team

    2016-10-01

    The arc discharge with a consumed anode is commonly used for synthesis of nanomaterials such as fullerenes, nanotubes and, more recently, graphene. The role of the arc plasma in nanosynthesis processes, including ablation of the graphite anode, nucleation and growth of nanostructures remains unclear. Our recent fast frame camera measurements revealed arc oscillations associated with the ablation processes at the anode. More sophisticated measurements using optical emission spectroscopy and spectrally resolved fast framing imaging revealed the complex, layered structure of plasma species distribution, which is dynamically changing. The results of this research include time- and space- resolved distributions of plasma species, plasma electron density and temperature. The obtained experimental data suggest a strong correlation between arc plasma parameters and nanosynthesis processes. This work was supported by US Department of Energy, Office of Science, Basic Energy Sciences, Materials Sciences and Engineering Division.

  7. Plasma recombination in runaway discharges in tokamak TCABR

    Energy Technology Data Exchange (ETDEWEB)

    Soboleva, T.K. [Universidad Nacional Autonoma de Mexico, Mexico City (Mexico). Inst. de Ciencias Nucleares; Galvao, R.M.O.; Kuznetsov, Yu. K.; Nascimento, I.C. [Sao Paulo Univ., SP (Brazil). Inst. de Fisica; Krasheninnikov, S.I. [University of California, San Diego, CA (United States)

    2002-03-01

    A new regime of runaway discharges has been observed in the TCABR tokamak. One of the most distinctive features of this regime is the effect of plasma detachment from the limiter. This experimental fact can only be explained by the volume recombination, which requires a low-temperature plasma. The analysis of the energy and particle balance in the system plasma-relativistic runaway beam in TCABR, which takes into account only the collisional mechanism of the heat transfer from runaways to thermal electrons, predicts electron temperatures T{sub e} = 0.1 - 2 eV; the temperature decreases with the neutral density increase. The recombination process with the rate constant around 10{sup -16} m3/s is required for the explanation of plasma density behavior in the experiment. At present, it is difficult to conclude about the mechanism of recombination. More reliable and detailed experimental data, mainly about the plasma temperature, are necessary. (author)

  8. Non-self-sustained discharge with hollow anode for plasma-based surface treatment

    Directory of Open Access Journals (Sweden)

    Misiruk Ivan O.

    2016-06-01

    Full Text Available The paper discusses plasma methods for surface modification using the non-self-sustained glow discharge with a hollow anode. This discharge is characterised by low voltage and high values of electron and ion currents. It can be easily excited in vacuum-arc installations that are widely used for coatings deposition. It is shown that such type of discharge may be effectively used for ion pumping, film deposition, ion etching, diffusion saturation of metallic materials, fusion and brazing of metals, and for combined application of above mentioned technologies in a single vacuum cycle.

  9. Transient charging and discharging current study in pure PVF and ...

    Indian Academy of Sciences (India)

    Keywords. PVF; PVDF; polyblend; fluoropolymers; transient current. Abstract. The transient current were analysed by considering the effect of variation of forming time, temperature, field and composition of blend specimens. Measurements indicated that transient charging and discharging currents exhibited thermally ...

  10. Electric Dipole Moment Experiment Systematic from Electric Field Discharge Current

    Science.gov (United States)

    Feinberg, B.; Gould, Harvey

    2014-09-01

    A magnetic field, in the direction of the electric field and synchronous with the electric field reversal, will mimic an EDM signal. One might expect a discharge across the electric field plates to produce magnetic fields with only small or vanishing components parallel to the electric field, minimizing its systematic effect. Our experimental model, using simulated discharge currents, found otherwise: the discharge current may be at an angle to the normal, and thus generate a normal magnetic field. Comparison of data from the experimental model with the results from calculations will be presented, along with estimates of the time-averaged normal magnetic field seen by atoms in an electron EDM experiment using a fountain of laser-cooled francium, as a function of discharge current.

  11. Optimization of hollow cathode discharge electrode for damage free remote plasma removal process for semiconductor manufacturing

    Science.gov (United States)

    Cho, Tae S.; Han, Qing; Yang, Dongqing; Park, Soonam; Lubomirsky, Dima; Venkataraman, Shankar

    2016-05-01

    Cone-shaped hollow cathode electrode configuration for a damage free remote plasma removal process has been optimized for given pressures based on Paschen characteristic curves, voltage-current characteristics and time-resolved discharge observations as well as oxide film removal performances. Remote plasmas have been generated in two types of cone-shaped electrodes with mixtures of He, NF3, and NH3 for pressure range of 1-30 Torr. Paschen characteristic curves and voltage-current (V-I) characteristics define an operating pressure for low breakdown voltage and the hollow cathode effect to minimize the particles. Sinusoidal voltage waveform and asymmetry electrode configuration alternate the glow discharge and hollow cathode discharge modes in a cycle. The current and infrared emission intensity from the glow discharge increases together for both cone-shaped electrodes with increasing pressure, whereas the hollow cathode discharge plasma emits strong infrared only when pD condition is satisfied. For the wide cone electrode configuration, high voltage operation at higher pressure results in particle contamination on the processed wafer by high energy ion bombardment. Operating at optimum pressure for a given electrode configuration shows faster oxide etch rate with better uniformity over a whole 300 mm wafer.

  12. Streptococci biofilm decontamination on teeth by low-temperature air plasma of dc corona discharges

    Science.gov (United States)

    Kovalóvá, Z.; Zahoran, M.; Zahoranová, A.; Machala, Z.

    2014-06-01

    Non-thermal plasmas of atmospheric pressure air direct current corona discharges were investigated for potential applications in dental medicine. The objective of this ex vivo study was to apply cold plasmas for the decontamination of Streptococci biofilm grown on extracted human teeth, and to estimate their antimicrobial efficiency and the plasma's impact on the enamel and dentine of the treated tooth surfaces. The results show that both positive streamer and negative Trichel pulse coronas can reduce bacterial population in the biofilm by up to 3 logs in a 10 min exposure time. This bactericidal effect can be reached faster (within 5 min) by electrostatic spraying of water through the discharge onto the treated tooth surface. Examination of the tooth surface after plasma exposure by infrared spectroscopy and scanning electron microscopy did not show any significant alteration in the tooth material composition or the tooth surface structures.

  13. Simulation Tool for Dielectric Barrier Discharge Plasma Actuators

    Science.gov (United States)

    Likhanskii, Alexander

    2014-01-01

    Traditional approaches for active flow separation control using dielectric barrier discharge (DBD) plasma actuators are limited to relatively low speed flows and atmospheric conditions. This results in low feasibility of the DBDs for aerospace applications. For active flow control at turbine blades, fixed wings, and rotary wings and on hypersonic vehicles, DBD plasma actuators must perform at a wide range of conditions, including rarified flows and combustion mixtures. An efficient, comprehensive, physically based DBD simulation tool can optimize DBD plasma actuators for different operation conditions. Researchers are developing a DBD plasma actuator simulation tool for a wide range of ambient gas pressures. The tool will treat DBD using either kinetic, fluid, or hybrid models, depending on the DBD operational condition.

  14. Dielectric barrier discharge plasma pretreatment on hydrolysis of microcrystalline cellulose

    Science.gov (United States)

    Huang, Fangmin; Long, Zhouyang; Liu, Sa; Qin, Zhenglong

    2017-04-01

    Dielectric barrier discharge (DBD) plasma was used as a pretreatment method for downstream hydrolysis of microcrystalline cellulose (MCC). The degree of polymerization (DP) of MCC decreased after it was pretreated by DBD plasma under a carrier gas of air/argon. The effectiveness of depolymerization was found to be influenced by the crystallinity of MCC when under the pretreatment of DBD plasma. With the addition of tert-butyl alcohol in the treated MCC water suspension solution, depolymerization effectiveness of MCC was inhibited. When MCC was pretreated by DBD plasma for 30 min, the total reducing sugar concentration (TRSC) and liquefaction yield (LY) of pretreated-MCC (PMCC) increased by 82.98% and 34.18% respectively compared with those for raw MCC.

  15. Properties Influencing Plasma Discharges in Packed Bed Reactors

    Science.gov (United States)

    Kruszelnicki, Juliusz; Engeling, Kenneth W.; Foster, John E.; Kushner, Mark J.

    2016-09-01

    Atmospheric pressure dielectric barrier discharges (DBDs) sustained in packed bed reactors (PBRs) are being investigated for CO2 removal and conversion of waste gases into higher value compounds. We report on results of a computational investigation of PBR-DBD properties using the plasma hydrodynamics simulator nonPDPSIM with a comparison to experiments. Dielectric beads (rods in 2D) were inserted between two coplanar electrodes, 1 cm apart filled by humid air. A step-pulse of -30 kV was applied to the top electrode. Material properties of the beads (dielectric constant, secondary emission coefficient) and gas properties (photoionization and photo-absorption cross-sections, temperature) were varied. We found that photoionization plays a critical role in the propagation of the discharge through the PBR, as it serves to seed charges in regions of high electric field. Increasing rates of photo-ionization enable increases in the discharge propagation velocity, ionization rates and production of radicals. A transition between DBD-like and arc-like discharges occurs as the radiation mean free path decreases. Increasing the dielectric constant of the beads increased electric fields in the gas, which translated to increased discharge propagation velocity and charge density until ɛ/ɛ0 100. Secondary electron emission coefficient and gas temperature have minimal impacts on the discharge propagation though the latter did affect the production of reactive species. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

  16. Laser-guided energetic discharges over large air gaps by electric-field enhanced plasma filaments

    Science.gov (United States)

    Théberge, Francis; Daigle, Jean-François; Kieffer, Jean-Claude; Vidal, François; Châteauneuf, Marc

    2017-01-01

    Recent works on plasma channels produced during the propagation of ultrashort and intense laser pulses in air demonstrated the guiding of electric discharges along the laser path. However, the short plasma lifetime limits the length of the laser-guided discharge. In this paper, the conductivity and lifetime of long plasma channels produced by ultrashort laser pulses is enhanced efficiently over many orders of magnitude by the electric field of a hybrid AC-DC high-voltage source. The AC electric pulse from a Tesla coil allowed to stimulate and maintain the highly conductive channel during few milliseconds in order to guide a subsequent 500 times more energetic discharge from a 30-kV DC source. This DC discharge was laser-guided over an air gap length of two metres, which is more than two orders of magnitude longer than the expected natural discharge length. Long plasma channel induced by laser pulses and stimulated by an external high-voltage source opens the way for wireless and efficient transportation of energetic current pulses over long air gaps and potentially for guiding lightning.

  17. Ethanol reforming in non-equilibrium plasma of glow discharge

    CERN Document Server

    Levko, D

    2012-01-01

    The results of a detailed kinetic study of the main plasma chemical processes in non-equilibrium ethanol/argon plasma are presented. It is shown that at the beginning of the discharge the molecular hydrogen is mainly generated in the reaction of ethanol H-abstraction. Later hydrogen is formed from active H, CH2OH and CH3CHOH and formaldehyde. Comparison with experimental data has shown that the used kinetic mechanism predicts well the concentrations of main species at the reactor outlet.

  18. Radiofrequency antenna for suppression of parasitic discharges in a helicon plasma thruster experiment

    Science.gov (United States)

    Takahashi, Kazunori

    2012-08-01

    A radiofrequency (rf) antenna for helicon plasma thruster experiments is developed and tested using a permanent magnets helicon plasma source immersed in a vacuum chamber. A magnetic nozzle is provided by permanent magnets arrays and an argon plasma is produced by a 13.56 MHz radiofrequency helicon-wave or inductively-coupled discharge. A parasitic discharge outside the source tube is successfully suppressed by covering the rf antenna with a ceramic ring and a grounded shield; a decrease in the ion saturation current of a Langmuir probe located outside the source tube is observed and the ion saturation current on axis increases simultaneously, compared with the case of a standard uncovered rf antenna. It is also demonstrated that the covered antenna can yield stable operation of the source.

  19. An Investigation of Leakage Current and Partial Discharge For

    Directory of Open Access Journals (Sweden)

    Arkan A. Hussain

    2013-05-01

    Full Text Available High voltage insulators used in various overhead forms are exposed to leakage current and partial discharge.This work deals with different structure forms of insulator, such as (pin post, clamp top and tie top. These structures are applied in different tests, as covered and stripped states. The leakage current for these forms were measured by raising the insulator voltage to (5.25, 6.35, 7.57 kV for covered and stripped state. Partial discharges were determined in covered and stripped state of these insulator forms using (straight and balanced detection method.Pin post insulators have a leakage current and electric field larger than both clamp top and tie top. The clamp top and tie top insulator show almost the same value of leakage current measurements.The stripped conductors always produce large partial discharge than covered conductor.

  20. Balancing current drive and heating in DIII-D high noninductive current fraction discharges through choice of the toroidal field

    Science.gov (United States)

    Ferron, J. R.; Holcomb, C. T.; Luce, T. C.; Politzer, P. A.; Turco, F.; DeBoo, J. C.; Doyle, E. J.; In, Y.; La Haye, R. J.; Murakami, M.; Okabayashi, M.; Park, J. M.; Petrie, T. W.; Petty, C. C.; Reimerdes, H.

    2011-11-01

    In order to maintain stationary values of the stored energy and the plasma current in a tokamak discharge with all of the current driven noninductively, the sum of the α-heating power and the power required to provide externally driven current must be equal to the power required to maintain the pressure against transport losses. In a study of high noninductive current fraction discharges in the DIII-D tokamak, it is shown that in the case of present-day tokamaks with no α-heating, adjustment of the toroidal field strength (BT) is a tool to obtain this balance between the required current drive and heating powers with other easily modifiable discharge parameters (βN, q95, discharge shape, ne) fixed at values chosen to satisfy specific constraints. With all of the external power sources providing both heating and current drive, and βN and q95 fixed, the fraction of externally driven current scales with BT with little change in the bootstrap current fraction, thus allowing the noninductive current fraction to be adjusted.

  1. Coherent structures induced by dielectric barrier discharge plasma actuator

    Science.gov (United States)

    Zhang, Xin; Li, Huaxing; Choi, Kwing So; Song, Longfei

    2017-11-01

    The structures of a flow field induced by a plasma actuator were investigated experimentally in quiescent air using high-speed Particle Image Velocimetry (PIV) technology. The motivation behind was to figure out the flow control mechanism of the plasma technique. A symmetrical Dielectric Barrier Discharge (DBD) plasma actuator was mounted on the suction side of the SC (2)-0714 supercritical airfoil. The results demonstrated that the plasma jet had some coherent structures in the separated shear layer and these structures were linked to a dominant frequency of f0 = 39 Hz when the peak-to-peak voltage of plasma actuator was 9.8 kV. The high speed PIV measurement of the induced airflow suggested that the plasma actuator could excite the flow instabilities which lead to production of the roll-up vortex. Analysis of transient results indicated that the roll-up vortices had the process of formation, movement, merging and breakdown. This could promote the entrainment effect of plasma actuator between the outside airflow and boundary layer flow, which is very important for flow control applications.

  2. Plasma Processing with a One Atmosphere Uniform Glow Discharge Plasma (OAUGDP)

    Science.gov (United States)

    Reece Roth, J.

    2000-10-01

    The vast majority of all industrial plasma processing is conducted with glow discharges at pressures below 10 torr. This has limited applications to high value workpieces as a result of the large capital cost of vacuum systems and the production constraints of batch processing. It has long been recognized that glow discharges would play a much larger industrial role if they could be operated at one atmosphere. The One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) has been developed at the University of Tennessee Plasma Sciences Laboratory. The OAUGDP is non-thermal RF plasma with the time-resolved characteristics of a classical low pressure DC normal glow discharge. An interdisciplinary team was formed to conduct exploratory investigations of the physics and applications of the OAUGDP. This team includes collaborators from the UTK Textiles and Nonwovens Development Center (TANDEC) and the Departments of Electrical and Computer Engineering, Microbiology, Food Science and Technology, and Mechanical and Aerospace Engineering and Engineering Science. Exploratory tests were conducted on a variety of potential plasma processing and other applications. These include the use of OAUGDP to sterilize medical and dental equipment and air filters; diesel soot removal; plasma aerodynamic effects; electrohydrodynamic (EDH) flow control of the neutral working gas; increasing the surface energy of materials; increasing the wettability and wickability of fabrics; and plasma deposition and directional etching. A general overview of these topics will be presented.

  3. Dielectric barrier discharge plasma actuator for flow control

    Science.gov (United States)

    Opaits, Dmitry Florievich

    Electrohydrodynamic (EHD) and magnetohydrodynamic phenomena are being widely studied for aerodynamic applications. The major effects of these phenomena are heating of the gas, body force generation, and enthalpy addition or extraction, [1, 2, 3]. In particular, asymmetric dielectric barrier discharge (DBD) plasma actuators are known to be effective EHD device in aerodynamic control, [4, 5]. Experiments have demonstrated their effectiveness in separation control, acoustic noise reduction, and other aeronautic applications. In contrast to conventional DBD actuators driven by sinusoidal voltages, we proposed and used a voltage profile consisting of nanosecond pulses superimposed on dc bias voltage. This produces what is essentially a non-self-sustained discharge: the plasma is generated by repetitive short pulses, and the pushing of the gas occurs primarily due to the bias voltage. The advantage of this non-self-sustained discharge is that the parameters of ionizing pulses and the driving bias voltage can be varied independently, which adds flexibility to control and optimization of the actuators performance. Experimental studies were conducted of a flow induced in a quiescent room air by a single DBD actuator. A new approach for non-intrusive diagnostics of plasma actuator induced flows in quiescent gas was proposed, consisting of three elements coupled together: the Schlieren technique, burst mode of plasma actuator operation, and 2-D numerical fluid modeling. During the experiments, it was found that DBD performance is severely limited by surface charge accumulation on the dielectric. Several ways to mitigate the surface charge were found: using a reversing DC bias potential, three-electrode configuration, slightly conductive dielectrics, and semi conductive coatings. Force balance measurements proved the effectiveness of the suggested configurations and advantages of the new voltage profile (pulses+bias) over the traditional sinusoidal one at relatively low

  4. Thrust Stand Measurements Using Alternative Propellants in the Microwave Assisted Discharge Inductive Plasma Accelerator

    Science.gov (United States)

    Hallock, Ashley K.; Polzin, Kurt A.

    2011-01-01

    Storable propellants (for example water, ammonia, and hydrazine) are attractive for deep space propulsion due to their naturally high density at ambient interplanetary conditions, which obviates the need for a cryogenic/venting system. Water in particular is attractive due to its ease of handling and availability both terrestrially and extra-terrestrially. While many storable propellants are reactive and corrosive, a propulsion scheme where the propellant is insulated from vulnerable (e.g. metallic) sections of the assembly would be well-suited to process these otherwise incompatible propellants. Pulsed inductive plasma thrusters meet this criterion because they can be operated without direct propellant-electrode interaction. During operation of these devices, electrical energy is capacitively stored and then discharged through an inductive coil creating a time-varying current in the coil that interacts with a plasma covering the face of the coil to induce a plasma current. Propellant is accelerated and expelled at a high exhaust velocity (O(10-100 km/s)) by the Lorentz body force arising from the interaction of the magnetic field and the induced plasma current. While this class of thruster mitigates the life-limiting issues associated with electrode erosion, many pulsed inductive plasma thrusters require high pulse energies to inductively ionize propellant. The Microwave Assisted Discharge Inductive Plasma Accelerator (MAD-IPA) is a pulsed inductive plasma thruster that addressees this issue by partially ionizing propellant inside a conical inductive coil before the main current pulse via an electron cyclotron resonance (ECR) discharge. The ECR plasma is produced using microwaves and a static magnetic field from a set of permanent magnets arranged to create a thin resonance region along the inner surface of the coil, restricting plasma formation, and in turn current sheet formation, to a region where the magnetic coupling between the plasma and the theta

  5. Simulation of plasma discharge in liquids: A detailed two-phase fluid approach

    Science.gov (United States)

    Charchi Aghdam, Ali; Farouk, Tanvir; Reacting Systems; Advanced Energy Research Laboratory Team

    2015-09-01

    Plasma discharge in liquids has gained great attention recently due to its applications in biomedical engineering, fuel processing, and water treatment and so on. Despite the tremendous interest, a comprehensive understanding of the underlying physics still remains limited. In the current work, an attempt is made to present a mathematical multi-physics model to describe the discharge of plasma in liquids. An in-house modeling platform is developed for simulating plasma formation in multiphase fluids. The model resolves a detailed two-phase fluid including viscous effects, surface tension, gravitational forces and electrical body force. All the governing equations are solved for gas and liquid phases. Electric field and charged species equations along with the plasma reaction kinetics are solved to get the charge distribution in the different phases as well as at the gas-liquid interface to obtain the electric body force acting at the interface. By coupling the above sub-models, a comprehensive multi-physics model for plasma discharge in liquids is constructed which is able to capture several physical aspects of the phenomena especially the role of the bubble, its motion and distortion on plasma characteristics.

  6. Expectation of ozone generation in alternating current corona discharges

    Science.gov (United States)

    Yehia, Ashraf; Mizuno, Akira

    2012-03-01

    An analytical study was made in this paper to calculate the ozone generation inside an ac corona discharge reactor. The corona discharges were formed in a coaxial wire-cylinder reactor. The reactor was fed by dry air flowing with constant rates at atmospheric pressure and room temperature and stressed by an ac voltage. Concentration of the ozone generated inside the reactor was measured as a function of the ac corona current under different discharge conditions. An empirical equation was derived from the experimental results for calculating the ozone concentration generated inside the reactor. The results, that have been calculated by using the derived equation, have agreed with the experimental results over the whole range of the investigated parameters. Therefore, the derived equation represents a suitable criterion for expecting the ozone concentration that will generate by ac coronas in dry air fed coaxial wire-cylinder reactors under any discharge conditions in range of the investigated parameters.

  7. Current drive for rotamak plasmas

    Indian Academy of Sciences (India)

    Fusion 30, 967 (1988). [6] D Brotherton-Ratcliffe and R G Storer, Plasma Phys. Contr. Fusion 31, 615 (1989). [7] I R Jones, C Deng, I M El-Fayoumi and P Euripides, Phys. Rev. Lett. 81, 2072 (1998). [8] A Sykes et al, Nuclear fusion 32, 694 (1992). [9] L McCarthy, Nuclear fusion 42, 1304 (2002). [10] R Storer, Chinese Phys.

  8. PREFACE: 12th International Conference on Gas Discharge Plasmas and Their Applications

    Science.gov (United States)

    Koval, N.; Landl, N.; Bogdan, A.; Yudin, A.

    2015-11-01

    The 12th International Conference ''Gas Discharge Plasmas and Their Applications'' (GDP 2015) was held in Tomsk, Russia, on September 6-11, 2015. GDP 2015 represents a continuation of the conferences on physics of gas discharge held in Russia since 1984 and seminars and conferences on the technological applications of low temperature plasmas traditionally organized in Tomsk. The six-day Conference brought together the specialists from different countries and organizations and provided an excellent opportunity to exchange knowledge, make oral contributions and poster presentations, and initiate discussions on the topics that are of interest to the Conference participants. The selected papers of the Conference cover a wide range of technical areas and modern aspects of the physical processes in the generators of low-temperature plasma, the low and high-pressure discharges, the pulsed plasma sources, the surface modification, and other gas-discharge technologies. The Conference was hosted by Institute of High Current Electronics SB RAS, Tomsk Polytechnic University, Tomsk Scientific Center, and Tomsk State University of Architecture and Building.

  9. Electrical discharges of plasma ozonizer and its application

    Directory of Open Access Journals (Sweden)

    Tirawanichakul, S.

    2007-05-01

    Full Text Available Ozone synthesis is one of the applications of near atmospheric plasma processing. An ozone generator in this research comprised two annular cylindrical-shaped electrodes. The inner electrode was made ofstainless steel covered with the dielectric glass and the outer electrode was also made of stainless steel. The electric spacing gap was 0.0075 m and length of ozonizer was 0.21 m. Oxygen gas passing through thedischarge gap between two electrodes supplied by an alternating current (AC high voltage power supply, frequency 50 Hz, ranging of 6-10 kVAC was used for producing ozone. The amount of ozone was determinedby the KI standard method. The result showed that the concentration of ozone is proportional to the AC applied voltage. For determining effect of purified oxygen feed rate of 6-10 L/min on quantity of ozone, theresults indicated that at the volumetric flow rate of 8 L/min produced the largest amount of ozone. In addition, ozone concentration at a flow rate of 8 L/min and an electrical discharge time of 3 minutes wasapproximately determined as 41, 60, 80 and 135 mg/L at 8, 9, 10 and 11 kVAC, respectively. Moreover, study of dye wastewater of Krajud mat was proposed and treated by three different methods. Firstly, dye wastewater was solely treated by a plasma ozonation. Secondly, a combination ofozonation and alum coagulation was used for dye wastewater treatment. Finally, the combined ozonation and activated carbon adsorption were used for dye wastewater treatment. The experimental results showedthat the percentage of light absorbance reduction of pink dyed wastewater for these three different methods was about 56%, 35% and 10%, respectively compared to the reference sample. In addition, For thesemethods, the percentage of BOD of treated dye wastewater could be reduced to 64%, 54% and 46% respectively, the percentage of COD could be reduced to approximately 78%, 62% and 27%, respectively, comparedto the reference sample. In conclusion, the

  10. Analysis on electromagnetic characteristics and military application of non-magnetized discharge plasma

    Science.gov (United States)

    Liu, Yang; Wang, Jiachun; Miao, Lei; Li, Zhigang

    2015-11-01

    Firstly, the dispersion equation of a plane electromagnetic wave in homogeneous and non-magnetized discharge plasma was established. According to the different frequency of electromagnetic wave and plasma parameters, the characteristics were discussed when the plasma interacted with electromagnetic waves. Then the gas discharge approach was put forward according to characteristics of plasma generated by different methods and their advantages and disadvantages. The possibility of using non-magnetized discharge plasma for the military purpose was analyzed. In the end, the principle and characteristics of the application of the non-magnetized discharge plasma were studied in the fields of stealth and protection against strong electromagnetic pulse.

  11. Plasma-enhanced photoemission as a discharge lamp diagnostic

    Science.gov (United States)

    Schulman, M. B.; Woodward, D. R.

    1989-10-01

    We describe our application of plasma-enhanced photoemission as an in situ electrode diagnostic for operating discharge lamps. The method uses focused low-power laser beams of various wavelengths to investigate emission properties of cathodes in fluorescent lamps. When a pulsed laser beam is directed onto the cathode, the photoemission effect will cause electrons to be ejected if hν is greater than the effective work function of the surface over the area illuminated. This burst of photoelectrons can be monitored, as well as the optogalvanic signal which results as they enter the surrounding discharge and produce additional ionization. The photon energy at which photoemission is observed places an upper limit on the local effective work function, which is influenced by the electric field at the cathode surface.

  12. Asymmetric SOL Current in Vertically Displaced Plasma

    Science.gov (United States)

    Cabrera, J. D.; Navratil, G. A.; Hanson, J. M.

    2017-10-01

    Experiments at the DIII-D tokamak demonstrate a non-monotonic relationship between measured scrape-off layer (SOL) currents and vertical displacement event (VDE) rates with SOL currents becoming largely n=1 dominant as plasma is displaced by the plasma control system (PCS) at faster rates. The DIII-D PCS is used to displace the magnetic axis 10x slower than the intrinsic growth time of similar instabilities in lower single-null plasmas. Low order (n control is disabled. Previous inquiry shows VDE asymmetry characterized by SOL current fraction and geometric parameters of tokamak plasmas. We note that, of plasmas displaced by the PCS, short displacement time scales near the limit of the PCS temporal control appear to result in larger n=1/n=2 asymmetries. Work supported under USDOE Cooperative Agreement DE-FC02-04ER54698 and DE-FG02-04ER54761.

  13. Monte Carlo Simulation of Normal and Abnormal Glow Discharge Plasmas Using the Limited Weight Probability Method

    Science.gov (United States)

    Goto, Makoto; Kondoh, Yoshiomi

    1998-01-01

    A self-consistent Monte Carlo modelling technique has been developed to study normal and abnormal glow discharge plasmas. To simulate nonequilibrium particles, a limited weight probability method is introduced and a fine subslab system is used. These two methods are applied to a DC Ar-like gas discharge simulation. The simulations are performed for conditions corresponding to the experimental voltage and current sets of normal and abnormal glow disharges. The characteristic spatial profiles of plasmas for normal and abnormal glow discharges with high nonequilibrium electron energy distributions are obtained. The increase in the current and the voltage from the normal glow leads to the following: (1) the density peak of the ions rises in the cathode region, (2) the density peak of electrons rises and catches up with that of ions and the peak position occurs closer to the cathode simultaneously; instead of a small increase of plasma density in the bulk plasma region, (3) reversal field strength next to the cathode fall increases and (4) the two groups of the enregy distribution separates into three groups at the cathode fall edge.

  14. Current-vortex filaments in magnetized plasmas

    NARCIS (Netherlands)

    Bergmans, J.; Kuvshinov, B. N.; Lakhin, V. P.; Schep, T. J.; Westerhof, E.

    1999-01-01

    Current-vortex filament solutions to the two-fluid plasma equations that describe drift-Alfven waves are presented. Such filament systems are Hamiltonian. Integrable three and four filament systems are discussed in some detail. A wide variety of orbit topologies exists in the plasma case. Special

  15. Effective secondary electron emission coefficient in DC abnormal glow discharge plasmas

    Science.gov (United States)

    Arumugam, Saravanan; Alex, Prince; Sinha, Suraj Kumar

    2017-11-01

    In this work, a self-consistent model has been used to estimate the effective secondary electron emission coefficient (γE) of the cathode in typical abnormal dc glow discharge conditions. Using this model, the value of γE has been obtained for tungsten (W), copper (Cu), and stainless steel (SS304) cathode samples for argon (Ar) and nitrogen (N2) discharges. The γE for W is lower than the Cu cathode under identical operating conditions. The results show possible dependence of γE on the Fermi energy of the cathode material since it influences the probability of electron to be emitted by the incident ion. In addition to this, we found, significant contribution of cathode directed species other than ion to γE. Further, the effect of pressure on γE for the N2 discharge has been investigated in the pressure range of 0.5 mbar to 2.0 mbar and its value increases from 0.38 to 0.47 with pressure for the SS304 cathode. The knowledge of γE successfully explains the governing processes in abnormal glow discharge plasma that cannot be explained by the value of the ion induced secondary electron emission coefficient γi. The measurement of the γE value of the cathode material in typical abnormal glow discharge plasma conditions presents possibilities of exciting advancement in various applications by accurate estimation of discharge characteristics including flux of species, fraction of power carried by ions and electrons, plasma density, discharge current density, etc.

  16. Potential Industrial Applications of the One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) Operating in Ambient Air

    Science.gov (United States)

    Reece Roth, J.

    2004-11-01

    The majority of industrial plasma processing with glow discharges has been conducted at pressures below 10 torr. This tends to limit applications to high value workpieces as a result of the high capital cost of vacuum systems and the production constraints of batch processing. It has long been recognized that glow discharge plasmas would play a much larger industrial role if they could be generated at one atmosphere. The One Atmosphere Uniform Glow Discharge Plasma (OAUGDP), developed at the University of Tennessee's Plasma Sciences Laboratory, is a non-thermal RF plasma operating on displacement currents with the time-resolved characteristics of a classical low pressure DC normal glow discharge. As a glow discharge, the OAUGDP operates with maximum electrical efficiency at the Stoletow point, where the energy input per ion-electron pair is a minimum [1, 2]. Several interdisciplinary teams have investigated potential applications of the OAUGDP. These teams included collaborators from the UTK Textiles and Nonwovens Development Center (TANDEC), and the Departments of Electrical and Computer Engineering, Microbiology, and Food Science and Technology, as well as the NASA Langley Research Center. The potential applications of the OAUGDP have all been at one atmosphere and room temperature, using air as the working gas. These applications include sterilizing medical and dental equipment; sterilizable air filters to deal with the "sick building syndrome"; removal of soot from Diesel engine exhaust; subsonic plasma aerodynamic effects, including flow re-attachment to airfoils and boundary layer modification; electrohydrodynamic (EDH) flow control of working gases; increasing the surface energy of materials; improving the adhesion of paints and electroplated layers: improving the wettability and wickability of fabrics; stripping of photoresist; and plasma deposition and directional etching of potential microelectronic relevance. [1] J. R. Roth, Industrial Plasma Engineering

  17. Dielectric Barrier Discharge Plasma Actuator for Flow Control

    Science.gov (United States)

    Opaits, Dmitry, F.

    2012-01-01

    This report is Part II of the final report of NASA Cooperative Agreement contract no. NNX07AC02A. It includes a Ph.D. dissertation. The period of performance was January 1, 2007 to December 31, 2010. Part I of the final report is the overview published as NASA/CR-2012- 217654. Asymmetric dielectric barrier discharge (DBD) plasma actuators driven by nanosecond pulses superimposed on dc bias voltage are studied experimentally. This produces non-self-sustained discharge: the plasma is generated by repetitive short pulses, and the pushing of the gas occurs primarily due to the bias voltage. The parameters of ionizing pulses and the driving bias voltage can be varied independently, which adds flexibility to control and optimization of the actuators performance. The approach consisted of three elements coupled together: the Schlieren technique, burst mode of plasma actuator operation, and 2-D numerical fluid modeling. During the experiments, it was found that DBD performance is severely limited by surface charge accumulation on the dielectric. Several ways to mitigate the surface charge were found: using a reversing DC bias potential, three-electrode configuration, slightly conductive dielectrics, and semi conductive coatings. Force balance measurements proved the effectiveness of the suggested configurations and advantages of the new voltage profile (pulses+bias) over the traditional sinusoidal one at relatively low voltages. In view of practical applications certain questions have been also addressed, such as electrodynamic effects which accompany scaling of the actuators to real size models, and environmental effects of ozone production by the plasma actuators.

  18. Dynamics of plasma electrode coupling in fluorescent lamp discharges

    Science.gov (United States)

    Garner, R.

    2008-07-01

    A time dependent model of a low pressure, mercury-rare gas discharge with thermionic electrode is presented. The model is applicable to ac-operated fluorescent lamps, which is the focus of this work. The model describes a one-dimensional negative glow plasma that is bounded on one side by a thermionic electrode and a sheath, and on the other by a positive column plasma. The electrode/sheath component of the model, together with the mutually interacting negative glow plasma, allows for self-consistent calculation of the electrode sheath potential. The model describes a smooth transition in the plasma parameters from electrode to positive column and thus reveals the spatial extent of the influence of the electrode and sheath processes. A detailed description of the model is presented, as well as results of calculations pertaining to a standard fluorescent lamp. Also shown are measurements from a 2 mm interferometer and an internal floating probe, both of which compare favourably with the calculations.

  19. Dynamics of plasma-electrode coupling in fluorescent lamp discharges

    Energy Technology Data Exchange (ETDEWEB)

    Garner, R [Central Research and Services Laboratory, OSRAM SYLVANIA, 71 Cherry Hill Drive, Beverly, MA 01915 (United States)], E-mail: richard.garner@sylvania.com

    2008-07-21

    A time dependent model of a low pressure, mercury-rare gas discharge with thermionic electrode is presented. The model is applicable to ac-operated fluorescent lamps, which is the focus of this work. The model describes a one-dimensional negative glow plasma that is bounded on one side by a thermionic electrode and a sheath, and on the other by a positive column plasma. The electrode/sheath component of the model, together with the mutually interacting negative glow plasma, allows for self-consistent calculation of the electrode sheath potential. The model describes a smooth transition in the plasma parameters from electrode to positive column and thus reveals the spatial extent of the influence of the electrode and sheath processes. A detailed description of the model is presented, as well as results of calculations pertaining to a standard fluorescent lamp. Also shown are measurements from a 2 mm interferometer and an internal floating probe, both of which compare favourably with the calculations.

  20. Improvement of water quality using dielectric barrier discharge plasma

    Science.gov (United States)

    Quyen, N. T.; Traikool, T.; Nitisoravut, R.; Onjun, T.

    2017-06-01

    The improvement of water quality using by atmospheric plasma produced from a dielectric barrier discharge (DBD) was studied. An experiment was set-up with a 4 mm diameter pipe, which contains 2 electrodes and has an air flow with the rate of 15 liters per minute. Surface water, domestic wastewater and DI water were treated with the DBD plasma for some period of time. Electricity was supplied at 3.5 kV with the frequency of 5.5 kHz. Some key parameters of water quality includes the level of chemical oxygen demand (COD), total suspended solid (TSS), color, and odor are measured before and after. The result showed that strong acid with pH below 2 was observed after 60 minutes plasma treatment for the DI water, while the surface water and wastewater needs about 120 minutes to pH below 2 even though the pH value are about the same at the beginning. Moreover, It was formed that the COD, TSS microorganism was noticeably decreased, therefore the increasing of transparency level. This result confirms that atmospheric DBD plasma generated acidity in water as reduce amount of organic and suspended solid in water.

  1. Electron beam injection experiments - The beam-plasma discharge at low pressures and magnetic field strengths

    Science.gov (United States)

    Bernstein, W.; Leinbach, H.; Kellogg, P.; Monson, S.; Hallinan, T.; Garriott, O. K.; Konradi, A.; Mccoy, J.; Daly, P.; Baker, B.

    1978-01-01

    The paper describes electron beam injection experiments which clarify observational results obtained in rocket flights. A column of enhanced density plasma, exceeding the density expected from ionization by primary beam electrons, was observed in a large vacuum system at low magnetic fields (1 to 1.5 G) and low ambient pressures (10 to the minus 6 to 10 to the minus 5 torr). The peak luminosity of the discharge was about 10 times that of the beam alone, and the radius increased by a factor of three. In the absence of the discharge, RF emission is observed at 1.1 to 1.2 times the cyclotron frequency, and a strong band of RF noise with upper frequency cutoff at about the cyclotron frequency is observed in the discharge mode, along with higher frequency noise at or near the plasma frequency. The onset of the plasma discharge is critically dependent on beam current. The described results agree with observations obtained at much higher densities and magnetic fields in fusion research studies.

  2. Nitric Oxide Studies in Low Temperature Plasmas Generated with a Nanosecond Pulse Sphere Gap Electrical Discharge

    Science.gov (United States)

    Burnette, David Dean

    This dissertation presents studies of NO kinetics in a plasma afterglow using various nanosecond pulse discharges across a sphere gap. The discharge platform is developed to produce a diffuse plasma volume large enough to allow for laser diagnostics in a plasma that is rich in vibrationally-excited molecules. This plasma is characterized by current and voltage traces as well as ICCD and NO PLIF images that are used to monitor the plasma dimensions and uniformity. Temperature and vibrational loading measurements are performed via coherent anti-Stokes Raman spectroscopy (CARS). Absolute NO concentrations are obtained by laser-induce fluorescence (LIF) measurements, and N and O densities are found using two photon absorption laser-induced fluorescence (TALIF). For all dry air conditions studied, the NO behavior is characterized by a rapid rate of formation consistent with an enhanced Zeldovich process involving electronically-excited nitrogen species that are generated within the plasma. After several microseconds, the NO evolution is entirely controlled by the reverse Zeldovich process. These results show that under the chosen range of conditions and even in extreme instances of vibrational loading, there is no formation channel beyond ~2 musec. Both the NO formation and consumption mechanisms are strongly affected by the addition of fuel species, producing much greater NO concentrations in the afterglow.

  3. Transmission characteristics of microwave in a glow-discharge dusty plasma

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Jieshu; Yuan, Chengxun, E-mail: yuancx@hit.edu.cn; Gao, Ruilin; Wang, Ying; Zhou, Zhong-Xiang [Department of Physics, Harbin Institute of Technology, Harbin 150001 (China); Liu, Sha; Yue, Feng [Shanghai Institute of Spaceflight Control Technology, Shanghai 200233 (China); Wu, Jian [China Research Institute of Radio wave Propagation, Qingdao 102206 (China); Li, Hui [Department of Physics, Harbin Institute of Technology, Harbin 150001 (China); China Research Institute of Radio wave Propagation, Qingdao 102206 (China)

    2016-07-15

    In this study, the propagation characteristics of electromagnetic wave in a glow discharge plasma with dust particles are experimentally investigated. A helium alternating current glow discharge plasmas have been successfully generated. Measurements of the plasma parameters using Langmuir probes, in the absence of dust particles, provide plasma densities (n{sub e}) of 10{sup 17 }m{sup −3} and electron temperatures (T{sub e}) ranging from 2 to 4 eV. Dusty plasmas are made by adding 30 nm radius aluminum oxide (Al{sub 2}O{sub 3}) particles into the helium plasma. The density of the dust particle (n{sub d}) in the device is about 10{sup 11}–10{sup 12 }m{sup −3}. The propagation characteristics of electromagnetic waves are determined by a vector network analyzer with 4–6 GHz antennas. An apparent attenuation by the dust is observed, and the measured attenuation data are approximately in accordance with the theoretical calculations. The effects of gas pressure and input power on the propagation are also investigated. Results show that the transmission attenuation increases with the gas pressure and input power, the charged dust particles play a significant role in the microwave attenuation.

  4. Electrostatic Discharge Current Linear Approach and Circuit Design Method

    Energy Technology Data Exchange (ETDEWEB)

    Katsivelis, Pavlos K.; Fotis, Georgios P.; Gonos, Ioannis F.; Koussiouris, Tryfon, G.; Stathopulos, Ioannis A. [School of Electrical and Computer Engineering, National Technical University of Athens (Greece)

    2010-10-15

    The Electrostatic Discharge phenomenon is a great threat to all electronic devices and ICs. An electric charge passing rapidly from a charged body to another can seriously harm the last one. However, there is a lack in a linear mathematical approach which will make it possible to design a circuit capable of producing such a sophisticated current waveform. The commonly accepted Electrostatic Discharge current waveform is the one set by the IEC 61000-4-2. However, the over-simplified circuit included in the same standard is incapable of producing such a waveform. Treating the Electrostatic Discharge current waveform of the IEC 61000-4-2 as reference, an approximation method, based on Prony’s method, is developed and applied in order to obtain a linear system’s response. Considering a known input, a method to design a circuit, able to generate this ESD current waveform in presented. The circuit synthesis assumes ideal active elements. A simulation is carried out using the PSpice software.

  5. Electrostatic discharge current linear approach and circuit design method

    Energy Technology Data Exchange (ETDEWEB)

    Katsivelis, P. K.; Fotis, G. P.; Gonos, I. F.; Koussiouris, T. G.; Stathopulos, I. A. [School of Electrical and Computer Engineering, National Technical University of Athens, 9 Iroon Polytechniou Str., Zographou 157 80, Athens (Greece)

    2010-11-15

    The electrostatic discharge (ESD) phenomenon is a great threat to all electronic devices and ICs. An electric charge passing rapidly from a charged body to another can seriously harm the last one. However, there is a lack in a linear mathematical approach which will make it possible to design a circuit capable of producing such a sophisticated current waveform. The commonly accepted electrostatic discharge current waveform is the one set by the IEC 61000-4-2. However, the over-simplified circuit included in the same standard is incapable of producing such a waveform. Treating the electrostatic discharge current waveform of the IEC 61000-4-2 as reference, an approximation method, based on Prony's method, is developed and applied in order to obtain a linear system's response. Considering a known input, a method to design a circuit, able to generate this ESD current waveform in presented. The circuit synthesis assumes ideal active elements. A simulation is carried out using the PSpice software. (authors)

  6. Dielectric barrier discharges: progress on plasma sources and on the understanding of regimes and single filaments

    Science.gov (United States)

    Brandenburg, Ronny

    2017-05-01

    Dielectric barrier discharges (DBDs) are plasmas generated in configurations with an insulating (dielectric) material between the electrodes which is responsible for a self-pulsing operation. DBDs are a typical example of nonthermal atmospheric or normal pressure gas discharges. Initially used for the generation of ozone, they have opened up many other fields of application. Therefore DBDs are a relevant tool in current plasma technology as well as an object for fundamental studies. Another motivation for further research is the fact that so-called partial discharges in insulated high voltage systems are special types of DBDs. The breakdown processes, the formation of structures, and the role of surface processes are currently under investigation. This review is intended to give an update to the already existing literature on DBDs considering the research and development within the last two decades. The main principles and different modes of discharge generation are summarized. A collection of known as well as special electrode configurations and reactor designs will be presented. This shall demonstrate the different and broad possibilities, but also the similarities and common aspects of devices for different fields of applications explored within the last years. The main part is devoted to the progress on the investigation of different aspects of breakdown and plasma formation with the focus on single filaments or microdischarges. This includes a summary of the current knowledge on the electrical characterization of filamentary DBDs. In particular, the recent new insights on the elementary volume and surface memory mechanisms in these discharges will be discussed. An outlook for the forthcoming challenges on research and development will be given.

  7. Measurement realities of current collection in dynamic space plasma environments

    Science.gov (United States)

    Szuszczewicz, Edward P.

    1990-01-01

    Theories which describe currents collected by conducting and non-conducting bodies immersed in plasmas have many of their concepts based upon the fundamentals of sheath-potential distributions and charged-particle behavior in superimposed electric and magnetic fields. Those current-collecting bodies (or electrodes) may be Langmuir probes, electric field detectors, aperture plates on ion mass spectrometers and retarding potential analyzers, or spacecraft and their rigid and tethered appendages. Often the models are incomplete in representing the conditions under which the current-voltage characteristics of the electrode and its system are to be measured. In such cases, the experimenter must carefully take into account magnetic field effects and particle anisotropies, perturbations caused by the current collection process itself and contamination on electrode surfaces, the complexities of non-Maxwellian plasma distributions, and the temporal variability of the local plasma density, temperature, composition and fields. This set of variables is by no means all-inclusive, but it represents a collection of circumstances guaranteed to accompany experiments involving energetic particle beams, plasma discharges, chemical releases, wave injection and various events of controlled and uncontrolled spacecraft charging. Here, an attempt is made to synopsize these diagnostic challenges and frame them within a perspective that focuses on the physics under investigation and the requirements on the parameters to be measured. Examples include laboratory and spaceborne applications, with specific interest in dynamic and unstable plasma environments.

  8. Characterization of nanosecond pulse driven dielectric barrier discharge plasma actuators for aerodynamic flow control

    Science.gov (United States)

    Dawson, Robert; Little, Jesse

    2013-03-01

    Positive polarity nanosecond pulse driven dielectric barrier discharge (ns-DBD) plasma actuators are studied experimentally in quiescent atmosphere. Pulse energy and instantaneous pulse power (hereafter referred to as energy and power) are calculated using simultaneous voltage and current measurements. Electrical characteristics are evaluated as a function of peak voltage, pulse frequency, discharge length, and dielectric thickness. Schlieren imaging is used to provide a relative estimate of discharge energy that is coupled to the near surface gas as heat for the same parameters. Characteristics of the DBD load have a substantial effect on the individual voltage and current traces which are reflected in the energy and power values. Power is mainly dependent on actuator length which is inconsistent with schlieren data as expected. Higher per unit length energy indicates a stronger compression wave for a given actuator geometry, but this is not universally true across different actuators suggesting some constructions more efficiently couple energy to the gas. Energy and compression wave strength are linearly related. Higher pulse frequency produces higher energy but is primarily attributed to heating of the actuator and power supply components and not to an optimal discharge frequency. Both energy and wave strength increase as peak voltage to the power of approximately 3.5 over a substantial range similar to ac-DBD plasma actuators.

  9. Synthesis of magnetic nanoparticles by atmospheric-pressure glow discharge plasma-assisted electrolysis

    Science.gov (United States)

    Shirai, Naoki; Yoshida, Taketo; Uchida, Satoshi; Tochikubo, Fumiyoshi

    2017-07-01

    For the synthesis of magnetic nanoparticles (NPs), we used plasma-assisted electrolysis in which atmospheric-pressure DC glow discharge using a liquid electrode is combined with electrolysis. The solution surface is exposed to positive ions or electrons in plasma. To synthesize magnetic NPs, aqueous solutions of FeCl2 or an iron electrode immersed in liquid was used to supply iron ions in the liquid. Magnetic NPs were synthesized at the plasma-liquid interface upon the electron irradiation of the liquid surface. In the case of using aqueous solutions of FeCl2, the condition of magnetic NP synthesis depended on the gas species of plasma and the chemical agent in the liquid for controlling oxidization. The amount of magnetic NPs synthesized using plasma is not very large. On the other hand, in the case of using an iron electrode immersed in NaCl solution, magnetic NPs were synthesized without using FeCl2 solutions. When plasma-assisted electrolysis was operated, the iron electrode eluted Fe cations, resulting in the formation of magnetic NPs at the plasma-liquid interface. Magnetic NP synthesis depended on the concentration of NaCl solution and discharge current. The magnetic NPs were identified to be magnetite. By using this method, more magnetite NPs were synthesized than in the case of plasma-assisted electrolysis with FeCl2 aqueous solutions. The pH of the liquid used in plasma-assisted electrolysis was important for the synthesis of magnetite NPs.

  10. Degradation of methyl tert-butyl ether (MTBE) in water by glow discharge plasma.

    Science.gov (United States)

    Tong, Shaoping; Ni, Yanyan; Shen, Chensi; Wen, Yuezhong; Jiang, Xuanzhen

    2011-01-01

    This study evaluated the ability of the glow discharge plasma (GDP) technique to degrade methyl tert-butyl ether (MTBE) in an aqueous solution. The results showed that a large amount of hydrogen peroxide and highly active *OH free radicals were produced during the treatment. Various experimental parameters including discharge current, initial MTBE concentration and initial pH played significant roles on MTBE degradation. In addition, Fe2+ had a catalytic effect on the degradation of MTBE, which is potentially attributable to the reaction between Fe3+ and the hydrated electron. It was also confirmed that GDP was comparable to electrocatalytic oxidation and high-density plasma and more efficient than photocatalytic degradation techniques. These results suggest that GDP may become a competitive MTBE wastewater treatment technology.

  11. AlGaN/GaN MOS-HEMTs with Corona-Discharge Plasma Treatment

    Directory of Open Access Journals (Sweden)

    Shuo-Huang Yuan

    2017-05-01

    Full Text Available The effects of a corona-discharge plasma treatment on the performance of an AlGaN/GaN metal-oxide-semiconductor high-electron mobility transistor fabricated onto Si substrates were studied. The threshold voltage shifted from −8.15 to −4.21 V when the device was treated with an Al2O3 layer. The leakage current was reduced from 2.9 × 10−5 to 4.2 × 10−7 mA/mm, and the ION/IOFF ratio increased from 8.3 × 106 to 7.3 × 108 using the corona-discharge plasma treatment, which exhibited an increase of about two orders of magnitude. The device exhibited excellent performance with a subthreshold swing of 78 mV/dec and a peak gain of 47.92 mS/mm at VGS = 10 V.

  12. High-brightness VUV sources based on plasma-dynamic magnetoplasma compressor discharges in gases

    Science.gov (United States)

    Kamrukov, A. S.; Kozlov, N. P.; Protasov, Iu. S.; Shashkovskii, S. G.

    1989-02-01

    The paper is concerned with the physical and technical aspects of the use of plasma-dynamic methods for generating high-power electromagnetic pulses over a wide spectral region, particularly in the UV and VUV spectral bands. In the experimental studies reviewed here, these methods are implemented by using high-current discharges of an erosion-type magnetoplasma compressor in gases. Approaches to the optimization of the energy and spectral-brightness characteristics of such discharges are discussed. The development of high power (1.5 GW) open-type plasma sources with a tunable emission spectrum and a light efficiency of 40-60 percent which can operate in the repetitively pulsed mode is reported.

  13. Simulation of Dual-Electrode Capacitively Coupled Plasma Discharges

    Science.gov (United States)

    Lu, Yijia; Ji, Linhong; Cheng, Jia

    2016-12-01

    Dual-electrode capacitively coupled plasma discharges are investigated here to lower the non-uniformity of plasma density. The dual-electrode structure proposed by Jung splits the electrode region and increases the flexibility of fine tuning non-uniformity. Different RF voltages, frequencies, phase-shifts and electrode areas are simulated and the influences are discussed. RF voltage and electrode area have a non-monotonic effect on non-uniformity, while frequency has a monotonic effect. Phase-shift has a cyclical influence on non-uniformity. A special combination of 224 V voltage and 11% area ratio with 10 MHz lowers the non-uniformity of the original set (200 V voltage and 0% area ratio with 10 MHz) by 46.5%. The position of the plasma density peak at the probe line has been tracked and properly tuning the phase-shift can obtain the same trace as tuning frequency or voltage. supported by National Natural Science Foundation of China (No. 51405261)

  14. Electric regimes and luminescent behavior of D C air glow discharge plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Delgado-Aparicio V, L.F. [Pontificia Universidad Catolica del Peru, Lima (Peru). Seccion Fisica. Grupo de Investigacion en Plasmas. E-mail: plasma@pucp.edu.pe

    1998-07-01

    A study of the electric regimes or modes with a brief summary on their dependence with the eight luminescent zones (between dark and glowing ones) of a DC air glow discharge plasma is presented. This research, carried out as part of a thesis, describes the electric behavior of the discharge through potential, current and resistance measurements. With these, we explain the strong dependence of the subnormal, normal and abnormal regimes with pressure and gap separation. Also we can correlate the previous conclusions with the luminescent analysis that we had made, finding that varying the pressure varies the length and luminous intensity of the three principal mechanisms in the discharge: the cathode and anode fall, and in between them, the positive column. (author)

  15. The magnetic field application for the gas discharge plasma control in processes of surface coating and modification

    Science.gov (United States)

    Asadullin, T. Ya; Galeev, I. G.

    2017-01-01

    In this paper the method of magnetic field application to control the gas discharge plasma effect on the various surfaces in processes of surface coating and modification is considered. The magnetic field directed perpendicular to the direction of electric current in the gas discharge plasma channel is capable to reject this plasma channel due to action of Lorentz force on the moving electrically charged particles [1,2]. The three-dimensional spatial structure of magnetic field is created by system of necessary quantity of the magnets located perpendicular to the direction of course of electric current in the gas-discharge plasma channel. The formation of necessary spatial distribution of magnetic field makes possible to obtain a required distribution of plasma parameters near the processed surfaces. This way of the plasma channel parameters spatial distribution management is the most suitable for application in processes of plasma impact on a surface of irregular shape and in cases when the selective impact of plasma on a part of a surface of a product is required. It is necessary to apply automated computer management of the process parameters [3] to the most effective plasma impact.

  16. A tomographic visualization of electric discharge sound fields in atmospheric pressure plasma using laser diffraction

    Science.gov (United States)

    Nakamiya, Toshiyuki; Mitsugi, Fumiaki; Iwasaki, Yoichiro; Ikegami, Tomoaki; Tsuda, Ryoichi; Sonoda, Yoshito; Danuta Stryczewska, Henryka

    2013-02-01

    The phase modulation of transparent gas can be detected using Fraunhofer diffraction technique, which we call optical wave microphone (OWM). The OWM is suitable for the detection of sonic wave from audible sound to ultrasonic wave. Because this technique has no influence on sound field or electric field during the measurement, we have applied it to the sound detection for the electric discharges. There is almost no research paper that uses the discharge sound to examine the electrical discharge phenomenon. Two-dimensional visualization of the sound field using the OWM is also possible when the computerized tomography (CT) is combined. In this work, coplanar dielectric barrier discharge sin different gases of Ar, N2, He were characterized via the OWM as well as applied voltage and discharge current. This is the first report to investigate the influence of the type of the atmospheric gas on the two-dimensional sound field distribution for the coplanar dielectric barrier discharge using the OWM with CT. Contribution to the Topical Issue "13th International Symposium on High Pressure Low Temperature Plasma Chemistry (Hakone XIII)", Edited by Nicolas Gherardi, Henryca Danuta Stryczewska and Yvan Ségui.

  17. Magnetic Ignition of Pulsed Gas Discharges in Air of Low Pressure in a Coaxial Plasma Gun

    Science.gov (United States)

    Thom, Karlheinz; Norwood, Joseph, Jr.

    1961-01-01

    The effect of an axial magnetic field on the breakdown voltage of a coaxial system of electrodes has been investigated by earlier workers. For low values of gas pressure times electrode spacing, the breakdown voltage is decreased by the application of the magnetic field. The electron cyclotron radius now assumes the role held by the mean free path in nonmagnetic discharges and the breakdown voltage becomes a function of the magnetic flux density. In this paper the dependence of the formative time lag as a function of the magnetic flux density is established and the feasibility of using a magnetic field for igniting high-voltage, high-current discharges is shown through theory and experiment. With a 36 microfarad capacitor bank charged to 48,000 volts, a peak current of 1.3 x 10( exp 6) amperes in a coaxial type of plasma gun was achieved with a current rise time of only 2 microseconds.

  18. Current status of plasma emission electronics: II. Hardware

    Science.gov (United States)

    Bugaev, A. S.; Vizir, A. V.; Gushenets, V. I.; Nikolaev, A. G.; Oks, E. M.; Yushkov, G. Yu.; Burachevsky, Yu. A.; Burdovitsin, V. A.; Osipov, I. V.; Rempe, N. G.

    2003-04-01

    This paper is devoted to the engineering embodiment of the modern methods for producing charged ion and electron beams by extracting them from the plasma of a discharge. Electron beams use to execute electron-beam welding, annealing, and surface heating of materials and to realize plasmochemical reactions stimulated by fast electrons. Ion beams allow realization of technologies of ion implantation or ion-assisted deposition of coatings thereby opening new prospects for the creation of compounds and alloys by the method that makes it possible to obtain desired parameters and functional properties of the surface. A detailed description is given to the performance and design of devices producing beams of this type: the ion and electron sources being developed at the laboratory of plasma sources of the Institute of High-Current Electronics of the Russian Academy of Sciences and the laboratory of plasma electronics of Tomsk State University of Control Systems and Radioelectronics.

  19. Uniform surface growth of copper oxide nanowires in radiofrequency plasma discharge and limiting factors

    Energy Technology Data Exchange (ETDEWEB)

    Filipič, Gregor; Mozetič, Miran; Cvelbar, Uroš, E-mail: uros.cvelbar@ijs.si [Jozef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Jozef Stefan International Postgraduate School, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Baranov, Oleg [Plasma Laboratory, National Aerospace University “KhAI,” Kharkov 61070 (Ukraine); Ostrikov, Kostya [CSIRO Manufacturing, P.O. Box 218, Lindfield, NSW 2070 (Australia); Plasma Nanoscience, School of Physics, The University of Sydney, Sydney, NSW 2006 (Australia); School of Chemistry, Physics, and Mechanical Engineering, Queensland University of Technology, Brisbane, QLD 4000 (Australia)

    2014-11-15

    The uniform growth of copper oxide nanowires on the top of copper plate has been investigated during the exposure to radiofrequency plasma discharge in respect to plasma properties and its localization. The copper samples of 10 mm radius and 1 mm in thickness were exposed to argon-oxygen plasma created at discharge power of 150 W. After 10 min, almost uniform growth of nanowires was achieved over large surface. There were significant distortions in nanowire length and shape near the edges. Based on the experimental results, we developed a theoretical model, which took into account a balance in heat released at the flow of the current to the nanowire and rejected from the nanowire. This model established a dependence of the maximal length of the nanowire at dependence on the plasma parameters, where the limiting factor for nanowire growth and distortions in distribution are ballistic effects of ions and their local fluxes. In contrast, the plasma heating by potential interactions of species has very little influence on the length and smaller deviations in flux are allowed for uniformity of growth.

  20. Plasmas in Multiphase Media: Bubble Enhanced Discharges in Liquids and Plasma/Liquid Phase Boundaries

    Energy Technology Data Exchange (ETDEWEB)

    Kushner, Mark Jay [University of Michigan

    2014-07-10

    In this research project, the interaction of atmospheric pressure plasmas with multi-phase media was computationally investigated. Multi-phase media includes liquids, particles, complex materials and porous surfaces. Although this investigation addressed fundamental plasma transport and chemical processes, the outcomes directly and beneficially affected applications including biotechnology, medicine and environmental remediation (e.g., water purification). During this project, we made advances in our understanding of the interaction of atmospheric pressure plasmas in the form of dielectric barrier discharges and plasma jets with organic materials and liquids. We also made advances in our ability to use computer modeling to represent these complex processes. We determined the method that atmospheric pressure plasmas flow along solid and liquid surfaces, and through endoscopic like tubes, deliver optical and high energy ion activation energy to organic and liquid surfaces, and produce reactivity in thin liquid layers, as might cover a wound. We determined the mechanisms whereby plasmas can deliver activation energy to the inside of liquids by sustaining plasmas in bubbles. These findings are important to the advancement of new technology areas such as plasma medicine

  1. Slope seeking for autonomous lift improvement by plasma surface discharge

    Science.gov (United States)

    Benard, Nicolas; Moreau, Eric; Griffin, John; Cattafesta, Louis N., III

    2010-05-01

    The present paper describes an experimental investigation of closed-loop separation control using plasma actuators. The post-stall-separated flow over a NACA 0015 airfoil is controlled using a single dielectric barrier discharge actuator located at the leading edge. Open-loop measurements are first performed to highlight the effects of the voltage amplitude on the control authority for freestream velocities of 10-30 m/s (chord Re = 1.3 × 105 to 4 × 105). The results indicate that partial or full reattachment can be achieved and motivate the choice of the slope seeking approach as the control algorithm. A single-input/single-output algorithm is used to autonomously seek the optimal voltage required to achieve the control objective (full flow reattachment associated with maximum lift). The paper briefly introduces the concept of slope seeking, and a detailed parameterization of the controller is considered. Static (fixed speed) closed-loop experiments are then discussed, which demonstrate the capability of the algorithm. In each case, the flow can be reattached in an autonomous fashion. The last part of the paper demonstrates the robustness of the gradient-based, model-free scheme for dynamic freestream conditions. This paper highlights the capability of slope seeking to autonomously achieve high lift when used to drive the voltage of a plasma actuator. It also describes the advantages and drawbacks of such a closed-loop approach.

  2. Turbulence Induced Distortion of Resonance Absorption in a Glow Discharge Tube's Plasma*

    Science.gov (United States)

    Johnson, J. A., III; Roberson, Stephen; Williams, Kyron; Appartaim, Richard

    1999-11-01

    The glow discharge tube provides a reliable turbulent plasma over a range of turbulent states with densities comparable to the tokamak divertor regions. The fully turbulent plasma state can be manipulated through changes in the tube's pressure and the tube's operating current. A pulsed OPO laser at 488.0nm excites Ar ions in the plasma which in turn provide resonant radiation at 422.7nm. We observe changes in the lifetime of the excited state which are correlated with changes in the nature of the local turbulence and changes in a superposed local magnetic field. These changes are interpreted using quantum mechanical enhancements of a modified kinetic theory. The results are applied to potential stability issues in the design of fusion power plants.

  3. Current Sheet Formation in a Conical Theta Pinch Faraday Accelerator with Radio-frequency Assisted Discharge

    Science.gov (United States)

    Polzin, Kurt A.; Hallock, Ashley K.; Choueiri, Edgar Y.

    2008-01-01

    Data from an inductive conical theta pinch accelerator are presented to gain insight into the process of inductive current sheet formation in the presence of a preionized background gas produced by a steady-state RF-discharge. The presence of a preionized plasma has been previously shown to allow for current sheet formation at lower discharge voltages and energies than those found in other pulsed inductive accelerator concepts, leading to greater accelerator efficiencies at lower power levels. Time-resolved magnetic probe measurements are obtained for different background pressures and pulse energies to characterize the effects of these parameters on current sheet formation. Indices are defined that describe time-resolved current sheet characteristics, such as the total current owing in the current sheet, the time-integrated total current ('strength'), and current sheet velocity. It is found that for a given electric field strength, maximums in total current, strength, and velocity occur for one particular background pressure. At other pressures, these current sheet indices are considerably smaller. The trends observed in these indices are explained in terms of the principles behind Townsend breakdown that lead to a dependence on the ratio of the electric field to the background pressure. Time-integrated photographic data are also obtained at the same experimental conditions, and qualitatively they compare quite favorably with the time-resolved magnetic field data.

  4. Plasma characterization in reactive sputtering processes of Ti in Ar/O2 mixtures operated in metal, transition and poisoned modes: a comparison between direct current and high-power impulse magnetron discharges

    Science.gov (United States)

    Haase, Fabian; Kersten, Holger; Lundin, Daniel

    2017-10-01

    Two reactive sputtering techniques have been studied: direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS), operated in various Ar/O2 gas mixtures using a Ti target. The processes were characterized during different modes of operation including pure argon, metallic, transition and compound mode. Energy flux data as well as data on electron density and temperature were combined to obtain knowledge about the trends and changes in the investigated internal process plasma properties for the different modes investigated. Although there is a large reduction of the mass deposition rate (a factor 10 in DCMS and a factor 14 in HiPIMS), when transiting from the metal to compound mode, we detect no significant decrease of the total energy flux in DCMS and only a minor decrease in HiPIMS ( <20%). Such a result is surprising considering that the neutral flux contribution to the total energy flux is known to be significant. Instead, we find that the reduction of the neutral component is compensated by an increase in the electron and ion flux components, which is experimentally detected as an increase of the effective electron temperature and a slightly increasing (DCMS) or essentially constant (HiPIMS) electron density with increasing oxygen flow rate.

  5. Parametric Investigation of Nanosecond Pulse Driven Dielectric Barrier Discharge Plasma Actuators for Aerodynamic Flow Control

    Science.gov (United States)

    Dawson, Robert; Little, Jesse

    2012-11-01

    Nanosecond pulse driven dielectric barrier discharge plasma actuators are studied experimentally in quiescent atmosphere. Per unit length peak energy and instantaneous peak power are calculated using simultaneous voltage and current measurements. Electrical characteristics are evaluated as a function of peak voltage, pulse frequency, discharge length and dielectric thickness. Schlieren imaging of compression waves is used to provide a relative measure of discharge energy that is coupled to the near surface gas as heat for the same parameters. Characteristics of the DBD load have a substantial effect on voltage and current traces which are reflected in the peak energy and peak power. Both peak energy and compression wave strength depend primarily on dielectric thickness and secondarily on actuator length although this is not universal in the case of energy necessitating examination of alternative calculation strategies. Peak power is mainly dependent on actuator length which is inconsistent with schlieren data as expected. Higher pulse frequency produces higher pulse energy, but is primarily attributed to heating of the actuator and power supply components. This effect is mainly observed for short actuators. Pulse energy increases as peak voltage to the power 3.5. This behavior is similar to observations of energy and thrust for ac-DBD plasma actuators suggesting that aspects of lumped-element circuit models may be applicable for optimizing ns-DBD performance.

  6. Nanosecond pulsed dielectric barrier discharge plasma-catalytic removal of HCHO in humid air

    Science.gov (United States)

    Zhang, Shuai; Wang, Wenchun; Zhang, Li; Zhao, Zilu; Yang, Dezheng

    2017-05-01

    Non-thermal plasma (NTP) has been regarded as a promising method for the removal of a wide range of low concentration volatile organic compounds (VOCs). In this paper, nanosecond pulsed and alternating current dielectric barrier discharge plasmas synergistic catalyst are utilized for removal of formaldehyde (HCHO) in humid air. Working gas is 1% H2O/21% O2/78% N2 with 154 ppm HCHO over total flow rate of 50 mL/min. Specific energy density (SED) are 32.5 JL-1, 35.8 JL-1 and 1069.2 JL-1 at power consumption of 0.325 W, 0.3 W, 8.9 W for removal of 67%, 63.8% and 73.8% HCHO when using bipolar nanosecond pulsed, unipolar nanosecond pulsed and AC dielectric barrier discharge (DBD) plasma, respectively. The removal efficiencies of HCHO using nanosecond pulsed DBD plasma increase approximately 10 20% when the packed-bed Al2O3 pellets exist and can reach up to almost 100% when TiO2 nanoparticles are used while the effect of CeO2 nanoparticles is a bit poor. Analysis indicate that OH radical and O atom play main role for removal HCHO and the gas temperature is a significant factor for its influence on rate constants of HCHO with active particles.

  7. Modeling of inhomogeneous mixing of plasma species in argon–steam arc discharge

    Science.gov (United States)

    Jeništa, J.; Takana, H.; Uehara, S.; Nishiyama, H.; Bartlová, M.; Aubrecht, V.; Murphy, A. B.

    2018-01-01

    This paper presents numerical simulation of mixing of argon- and water-plasma species in an argon–steam arc discharge generated in a thermal plasma generator with the combined stabilization of arc by axial gas flow (argon) and water vortex. The diffusion of plasma species itself is described by the combined diffusion coefficients method in which the coefficients describe the diffusion of argon ‘gas,’ with respect to water vapor ‘gas.’ Diffusion processes due to the gradients of mass density, temperature, pressure, and an electric field have been considered in the model. Calculations for currents 150–400 A with 15–22.5 standard liters per minute (slm) of argon reveal inhomogeneous mixing of argon and oxygen–hydrogen species with the argon species prevailing near the arc axis. All the combined diffusion coefficients exhibit highly nonlinear distribution of their values within the discharge, depending on the temperature, pressure, and argon mass fraction of the plasma. The argon diffusion mass flux is driven mainly by the concentration and temperature space gradients. Diffusions due to pressure gradients and due to the electric field are of about 1 order lower. Comparison with our former calculations based on the homogeneous mixing assumption shows differences in temperature, enthalpy, radiation losses, arc efficiency, and velocity at 400 A. Comparison with available experiments exhibits very good qualitative and quantitative agreement for the radial temperature and velocity profiles 2 mm downstream of the exit nozzle.

  8. On the physical processes ruling an atmospheric pressure air glow discharge operating in an intermediate current regime

    Energy Technology Data Exchange (ETDEWEB)

    Prevosto, L., E-mail: prevosto@waycom.com.ar; Mancinelli, B.; Chamorro, J. C.; Cejas, E. [Grupo de Descargas Eléctricas, Departamento Ing. Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, Venado Tuerto (2600), Santa Fe (Argentina); Kelly, H. [Grupo de Descargas Eléctricas, Departamento Ing. Electromecánica, Facultad Regional Venado Tuerto (UTN), Laprida 651, Venado Tuerto (2600), Santa Fe (Argentina); Instituto de Física del Plasma (CONICET), Facultad de Ciencias Exactas y Naturales (UBA) Ciudad Universitaria Pab. I, 1428, Buenos Aires (Argentina)

    2015-02-15

    Low-frequency (100 Hz), intermediate-current (50 to 200 mA) glow discharges were experimentally investigated in atmospheric pressure air between blunt copper electrodes. Voltage–current characteristics and images of the discharge for different inter-electrode distances are reported. A cathode-fall voltage close to 360 V and a current density at the cathode surface of about 11 A/cm{sup 2}, both independent of the discharge current, were found. The visible emissive structure of the discharge resembles to that of a typical low-pressure glow, thus suggesting a glow-like electric field distribution in the discharge. A kinetic model for the discharge ionization processes is also presented with the aim of identifying the main physical processes ruling the discharge behavior. The numerical results indicate the presence of a non-equilibrium plasma with rather high gas temperature (above 4000 K) leading to the production of components such as NO, O, and N which are usually absent in low-current glows. Hence, the ionization by electron-impact is replaced by associative ionization, which is independent of the reduced electric field. This leads to a negative current-voltage characteristic curve, in spite of the glow-like features of the discharge. On the other hand, several estimations show that the discharge seems to be stabilized by heat conduction; being thermally stable due to its reduced size. All the quoted results indicate that although this discharge regime might be considered to be close to an arc, it is still a glow discharge as demonstrated by its overall properties, supported also by the presence of thermal non-equilibrium.

  9. Effect of dielectric and liquid on plasma sterilization using dielectric barrier discharge plasma.

    Science.gov (United States)

    Mastanaiah, Navya; Johnson, Judith A; Roy, Subrata

    2013-01-01

    Plasma sterilization offers a faster, less toxic and versatile alternative to conventional sterilization methods. Using a relatively small, low temperature, atmospheric, dielectric barrier discharge surface plasma generator, we achieved ≥ 6 log reduction in concentration of vegetative bacterial and yeast cells within 4 minutes and ≥ 6 log reduction of Geobacillus stearothermophilus spores within 20 minutes. Plasma sterilization is influenced by a wide variety of factors. Two factors studied in this particular paper are the effect of using different dielectric substrates and the significance of the amount of liquid on the dielectric surface. Of the two dielectric substrates tested (FR4 and semi-ceramic (SC)), it is noted that the FR4 is more efficient in terms of time taken for complete inactivation. FR4 is more efficient at generating plasma as shown by the intensity of spectral peaks, amount of ozone generated, the power used and the speed of killing vegetative cells. The surface temperature during plasma generation is also higher in the case of FR4. An inoculated FR4 or SC device produces less ozone than the respective clean devices. Temperature studies show that the surface temperatures reached during plasma generation are in the range of 30°C-66 °C (for FR4) and 20 °C-49 °C (for SC). Surface temperatures during plasma generation of inoculated devices are lower than the corresponding temperatures of clean devices. pH studies indicate a slight reduction in pH value due to plasma generation, which implies that while temperature and acidification may play a minor role in DBD plasma sterilization, the presence of the liquid on the dielectric surface hampers sterilization and as the liquid evaporates, sterilization improves.

  10. Effect of dielectric and liquid on plasma sterilization using dielectric barrier discharge plasma.

    Directory of Open Access Journals (Sweden)

    Navya Mastanaiah

    Full Text Available Plasma sterilization offers a faster, less toxic and versatile alternative to conventional sterilization methods. Using a relatively small, low temperature, atmospheric, dielectric barrier discharge surface plasma generator, we achieved ≥ 6 log reduction in concentration of vegetative bacterial and yeast cells within 4 minutes and ≥ 6 log reduction of Geobacillus stearothermophilus spores within 20 minutes. Plasma sterilization is influenced by a wide variety of factors. Two factors studied in this particular paper are the effect of using different dielectric substrates and the significance of the amount of liquid on the dielectric surface. Of the two dielectric substrates tested (FR4 and semi-ceramic (SC, it is noted that the FR4 is more efficient in terms of time taken for complete inactivation. FR4 is more efficient at generating plasma as shown by the intensity of spectral peaks, amount of ozone generated, the power used and the speed of killing vegetative cells. The surface temperature during plasma generation is also higher in the case of FR4. An inoculated FR4 or SC device produces less ozone than the respective clean devices. Temperature studies show that the surface temperatures reached during plasma generation are in the range of 30°C-66 °C (for FR4 and 20 °C-49 °C (for SC. Surface temperatures during plasma generation of inoculated devices are lower than the corresponding temperatures of clean devices. pH studies indicate a slight reduction in pH value due to plasma generation, which implies that while temperature and acidification may play a minor role in DBD plasma sterilization, the presence of the liquid on the dielectric surface hampers sterilization and as the liquid evaporates, sterilization improves.

  11. Effect of Dielectric and Liquid on Plasma Sterilization Using Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Mastanaiah, Navya; Johnson, Judith A.; Roy, Subrata

    2013-01-01

    Plasma sterilization offers a faster, less toxic and versatile alternative to conventional sterilization methods. Using a relatively small, low temperature, atmospheric, dielectric barrier discharge surface plasma generator, we achieved ≥6 log reduction in concentration of vegetative bacterial and yeast cells within 4 minutes and ≥6 log reduction of Geobacillus stearothermophilus spores within 20 minutes. Plasma sterilization is influenced by a wide variety of factors. Two factors studied in this particular paper are the effect of using different dielectric substrates and the significance of the amount of liquid on the dielectric surface. Of the two dielectric substrates tested (FR4 and semi-ceramic (SC)), it is noted that the FR4 is more efficient in terms of time taken for complete inactivation. FR4 is more efficient at generating plasma as shown by the intensity of spectral peaks, amount of ozone generated, the power used and the speed of killing vegetative cells. The surface temperature during plasma generation is also higher in the case of FR4. An inoculated FR4 or SC device produces less ozone than the respective clean devices. Temperature studies show that the surface temperatures reached during plasma generation are in the range of 30°C–66°C (for FR4) and 20°C–49°C (for SC). Surface temperatures during plasma generation of inoculated devices are lower than the corresponding temperatures of clean devices. pH studies indicate a slight reduction in pH value due to plasma generation, which implies that while temperature and acidification may play a minor role in DBD plasma sterilization, the presence of the liquid on the dielectric surface hampers sterilization and as the liquid evaporates, sterilization improves. PMID:23951023

  12. Relative Contribution of Volume and Surface-Plasma Generation of Negative Ions in Gas Discharges

    CERN Document Server

    Dudnikov, Vadim

    2005-01-01

    The relative contribution of volume and surface-plasma generation of extracted ?- ions in gas discharge sources will be analyzed. At the present time, it is well known that surface-plasma generation of extracted ?- ion is dominate above volume processes in discharges with admixture of cesium or other catalysts with low ionization potential. We will attract attention to evidences, that surface-plasma generation can be enhanced in high density discharges without cesium after electrode activation by high temperature conditioning in discharge. A diffusion of impurity with a low ionization potential can be a reason of observed enhancement of H-

  13. Diagnostic of capacitively coupled radio frequency plasma from electrical discharge characteristics: comparison with optical emission spectroscopy and fluid model simulation

    Science.gov (United States)

    Xiang, HE; Chong, LIU; Yachun, ZHANG; Jianping, CHEN; Yudong, CHEN; Xiaojun, ZENG; Bingyan, CHEN; Jiaxin, PANG; Yibing, WANG

    2018-02-01

    The capacitively coupled radio frequency (CCRF) plasma has been widely used in various fields. In some cases, it requires us to estimate the range of key plasma parameters simpler and quicker in order to understand the behavior in plasma. In this paper, a glass vacuum chamber and a pair of plate electrodes were designed and fabricated, using 13.56 MHz radio frequency (RF) discharge technology to ionize the working gas of Ar. This discharge was mathematically described with equivalent circuit model. The discharge voltage and current of the plasma were measured at different pressures and different powers. Based on the capacitively coupled homogeneous discharge model, the equivalent circuit and the analytical formula were established. The plasma density and temperature were calculated by using the equivalent impedance principle and energy balance equation. The experimental results show that when RF discharge power is 50–300 W and pressure is 25–250 Pa, the average electron temperature is about 1.7–2.1 eV and the average electron density is about 0.5 × 1017–3.6 × 1017 m‑3. Agreement was found when the results were compared to those given by optical emission spectroscopy and COMSOL simulation.

  14. Investigation of operating parameters on CO2 splitting by dielectric barrier discharge plasma

    Science.gov (United States)

    Pan, CHEN; Jun, SHEN; Tangchun, RAN; Tao, YANG; Yongxiang, YIN

    2017-12-01

    Experiments of CO2 splitting by dielectric barrier discharge (DBD) plasma were carried out, and the influence of CO2 flow rate, plasma power, discharge voltage, discharge frequency on CO2 conversion and process energy efficiency were investigated. It was shown that the absolute quantity of CO2 decomposed was only proportional to the amount of conductive electrons across the discharge gap, and the electron amount was proportional to the discharge power; the energy efficiency of CO2 conversion was almost a constant at a lower level, which was limited by CO2 inherent discharge character that determined a constant gap electric field strength. This was the main reason why CO2 conversion rate decreased as the CO2 flow rate increase and process energy efficiency was decreased a little as applied frequency increased. Therefore, one can improve the CO2 conversion by less feed flow rate or larger discharge power in DBD plasma, but the energy efficiency is difficult to improve.

  15. Effect of Secondary Electron Emission on Electron Cross-Field Current in E×B Discharges

    Energy Technology Data Exchange (ETDEWEB)

    Yevgeny Raitses, Igor D. Kaganovich, Alexander Khrabrov, Dmytro Sydorenko, Nathaniel J. Fisch and Andrei Smolyakov

    2011-02-10

    This paper reviews and discusses recent experimental, theoretical, and numerical studies of plasma-wall interaction in a weakly collisional magnetized plasma bounded with channel walls made from different materials. A lowpressure ExB plasma discharge of the Hall thruster was used to characterize the electron current across the magnetic field and its dependence on the applied voltage and electron-induced secondary electron emission (SEE) from the channel wall. The presence of a depleted, anisotropic electron energy distribution function with beams of secondary electrons was predicted to explain the enhancement of the electron cross-field current observed in experiments. Without the SEE, the electron crossfield transport can be reduced from anomalously high to nearly classical collisional level. The suppression of SEE was achieved using an engineered carbon velvet material for the channel walls. Both theoretically and experimentally, it is shown that the electron emission from the walls can limit the maximum achievable electric field in the magnetized plasma. With nonemitting walls, the maximum electric field in the thruster can approach a fundamental limit for a quasineutral plasma.

  16. Characteristics of plasma sterilizer using microwave torch plasma with AC high-voltage discharge plasma

    Science.gov (United States)

    Itarashiki, Tomomasa; Hayashi, Nobuya; Yonesu, Akira

    2016-01-01

    Microwave plasma sterilization has recently been attracting attention for medical applications. However, it is difficult to perform low-temperature sterilization in short time periods. Increasing the output power shortens the time required for sterilization but causes the temperature to increase. To overcome this issue, we have developed a hybrid plasma system that combines a microwave torch plasma and a high-voltage mesh plasma, which allows radicals to be produced at low temperatures. Using this system, successful sterilization was shown to be possible in a period of 45 min at a temperature of 41 °C.

  17. Endotoxin removal by radio frequency gas plasma (glow discharge)

    Science.gov (United States)

    Poon, Angela

    2011-12-01

    Contaminants remaining on implantable medical devices, even following sterilization, include dangerous fever-causing residues of the outer lipopolysaccharide-rich membranes of Gram-negative bacteria such as the common gut microorganism E. coli. The conventional method for endotoxin removal is by Food & Drug Administration (FDA)-recommended dry-heat depyrogenation at 250°C for at least 45 minutes, an excessively time-consuming high-temperature technique not suitable for low-melting or heat-distortable biomaterials. This investigation evaluated the mechanism by which E. coli endotoxin contamination can be eliminated from surfaces during ambient temperature single 3-minute to cumulative 15-minute exposures to radio-frequency glow discharge (RFGD)-generated residual room air plasmas activated at 0.1-0.2 torr in a 35MHz electrodeless chamber. The main analytical technique for retained pyrogenic bio-activity was the Kinetic Chromogenic Limulus Amebocyte Lysate (LAL) Assay, sufficiently sensitive to document compliance with FDA-required Endotoxin Unit (EU) titers less than 20 EU per medical device by optical detection of enzymatic color development corresponding to LAL Assay of sterile water extracts from both glass and Ge specimens. The Ge prism MAIR-IR measurements were repeated after employing 3-minute RFGD treatments sequentially for more than 10 cycles to observe removal of deposited matter that correlated with diminished EU titers. The results showed that 5 cycles, for a total exposure time of 15 minutes to low-temperature gas plasma, was sufficient to reduce endotoxin titers to below 0.05 EU/ml, and correlated with concurrent reduction of major endotoxin reference standard absorption bands at 3391 cm-1, 2887 cm-1, 1646 cm -1 1342 cm-1, and 1103 cm-1 to less than 0.05 Absorbance Units. Band depletion varied from 15% to 40% per 3-minute cycle of RFGD exposure, based on peak-to-peak analyses. In some cases, 100% of all applied biomass was removed within 5 sequential

  18. Plasma nitriding of aluminium in a pulsed dc glow discharge of nitrogen

    Science.gov (United States)

    Naseer, S.; Khan, F. U.; Rehman, N. U.; Qayyum, A.; Rahman, F.; Zakaullah, M.

    2010-02-01

    Plasma nitriding of aluminium in a 50 Hz pulsed-dc glow discharge is studied for different ion-current densities (2.0-5.0 mA cm-2) by keeping the corresponding discharge parameters such as treatment time, chamber pressure, substrate temperature and gas composition same. The treated samples are analysed for changes induced in surface properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and Vickers's micro-hardness testing. XRD showed the downshift in the original diffraction peak corresponding to (111) plane reflection along with the emergence of new diffraction peak corresponding to (220) plane reflection, confirming the N-diffusion into existing Al-lattice and formation of AlN compound. Surface hardness is significantly improved which might be attributed to the diffusion of nitrogen and compound layer formation.

  19. Numerical simulation of Trichel pulses of negative DC corona discharge based on a plasma chemical model

    Science.gov (United States)

    Chen, Xiaoyue; Lan, Lei; Lu, Hailiang; Wang, Yu; Wen, Xishan; Du, Xinyu; He, Wangling

    2017-10-01

    A numerical simulation method of negative direct current (DC) corona discharge based on a plasma chemical model is presented, and a coaxial cylindrical gap is adopted. There were 15 particle species and 61 kinds of collision reactions electrons involved, and 22 kinds of reactions between ions are considered in plasma chemical reactions. Based on this method, continuous Trichel pulses are calculated on about a 100 us timescale, and microcosmic physicochemical process of negative DC corona discharge in three different periods is discussed. The obtained results show that the amplitude of Trichel pulses is between 1-2 mA, and that pulse interval is in the order of 10-5 s. The positive ions produced by avalanche ionization enhanced the electric field near the cathode at the beginning of the pulse, then disappeared from the surface of cathode. The electric field decreases and the pulse ceases to develop. The negative ions produced by attachment slowly move away from the cathode, and the electric field increases gradually until the next pulse begins to develop. The positive and negative ions with the highest density during the corona discharge process are O4+ and O3- , respectively.

  20. Physics and Chemistry of MW Laser-induced Discharge in Gas Flows and Plasma Jets

    Science.gov (United States)

    2007-12-01

    can be quasi-stationary coaxial plasma accelerators (MPC). This type of accelerators generates plasma jets of different gases (H2, He, N2, Ar) with...gas is ionizing and accelerating in discharge processing. For this regime the plasma gun generates the plasma jets of different gases3 (H2, He, N2...spectrometers. Spectrometers 1 and 2 are used for measuring of time behavior of single spectral lines, emitting in the focus area of plasma gun . Usually

  1. Fluid model for a partially packed dielectric barrier discharge plasma reactor

    Science.gov (United States)

    Gadkari, Siddharth; Tu, Xin; Gu, Sai

    2017-09-01

    In this work, a two-dimensional numerical fluid model is developed for a partially packed dielectric barrier discharge (DBD) in pure helium. Influence of packing on the discharge characteristics is studied by comparing the results of DBD with partial packing with those obtained for DBD with no packing. In the axial partial packing configuration studied in this work, the electric field strength was shown to be enhanced at the top surface of the spherical packing material and at the contact points between the packing and the dielectric layer. For each value of applied potential, DBD with partial packing showed an increase in the number of pulses in the current profile in the positive half cycle of the applied voltage, as compared to DBD with no packing. Addition of partial packing to the plasma-alone DBD also led to an increase in the electron and ion number densities at the moment of breakdown. The time averaged electron energy profiles showed that a much higher range of electron energy can be achieved with the use of partial packing as compared to no packing in a DBD, at the same applied power. The spatially and time averaged values over one voltage cycle also showed an increase in power density and electron energy on inclusion of partial packing in the DBD. For the applied voltage parameters studied in this work, the discharge was found to be consistently homogeneous and showed the characteristics of atmospheric pressure glow discharge.

  2. Temporal distribution of linear densities of the plasma column in a plasma focus discharge

    Directory of Open Access Journals (Sweden)

    Cikhardtova Balzhima

    2015-06-01

    Full Text Available Experiments were carried out on the PF-1000 plasma focus device, with a deuterium filling and with deuterium puffing from a gas-puff nozzle placed on the axis of the anode face. The current was reaching 2 MA. 15 interferometric frames from one shot were recorded with a Nd:YLF laser and a Mach–Zehnder interferometer, with 10–20 ns delay between the frames. As a result, the temporal and spatial distribution of the linear densities and the radial and axial velocities of the moving of plasma in the dense plasma column could be estimated.

  3. Analysis on discharge process of a plasma-jet triggered gas spark switch

    Science.gov (United States)

    Weihao, TIE; Cui, MENG; Yuting, ZHANG; Zirang, YAN; Qiaogen, ZHANG

    2018-01-01

    The plasma-jet triggered gas switch (PJTGS) could operate at a low working coefficient with a low jitter. We observed and analyzed the discharge process of the PJTGS at the lowest working coefficient of 47% with the trigger voltage of 40 kV and the pulse energy of 2 J to evaluate the effect of the plasma jet. The temporal and spatial evolution and the optical emission spectrum of the plasma jet were captured. And the spraying delay time and outlet velocity under different gas pressures were investigated. In addition, the particle in cell with Monte Carlo collision was employed to obtain the particle distribution of the plasma jet varying with time. The results show that, the plasma jet generated by spark discharge is sprayed into a spark gap within tens of nanoseconds, and its outlet velocity could reach 104 m s‑1. The plasma jet plays a non-penetrating inducing role in the triggered discharge process of the PJTGS. On the one hand, the plasma jet provides the initial electrons needed by the discharge; on the other hand, a large number of electrons focusing on the head of the plasma jet distort the electric field between the head of the plasma jet and the opposite electrode. Therefore, a fast discharge originated from the plasma jet is induced and quickly bridges two electrodes.

  4. Nonlinear current sheet formation in ideal plasmas

    Science.gov (United States)

    Voge, A.; Schindler, K.; Otto, A.

    1994-01-01

    We present a numerical study of the formation of current sheets in ideal plasmas. First we confirm the development of singular current sheets in a one-dimensional model. In a second step we extend the analysis to two-dimensional equilibria. Here it is found that the resulting structures are quiet insensitive to the boundary conditions. For the special case of a magnetotail like equilibrium it will be shown that the resulting current distribution provides a possibility to understand the onset of a localized anomalous resistivity from a macroscopic point of view. Furthermore, the resulting structures provide an explanation for the dramatic decrease of the thickness of the current sheet in the magnetotail prior to the onset of geomagnetic substorms.

  5. Lower hybrid current drive in tokamak plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Ushigusa, Kenkichi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    1999-03-01

    Past ten years progress on Lower Hybrid Current Drive (LHCD) experiments have demonstrated the largest non-inductive current (3.6 MA, JT-60U), the longest current sustainment (2 hours, TRIAM-1M), non-inductive current drive at the highest density (n-bar{sub e} - 10{sup 20}m{sup -3}, ALCATOR-C) and the highest current drive efficiency ({eta}{sub CD} = 3.5x10{sup 19} m{sup -2}A/W, JT-60). These results indicate that LHCD is one of the most promising methods to drive non-inductive current in the present tokamak plasmas. This paper presents recent experimental results on LHCD experiments. Basic theories of LH waves, the wave propagation and the current drive are briefly summarized. The main part of this paper describes several important results and their physical pictures on recent LHCD experiments; 1) the experimental set-up, 2) the current drive efficiency, 3) the control of current profile and MHD activities, 4) the global energy confinement, 5) the global power flow, 6) fast electron behavior, 7) interaction between LH waves and thermal/fast ions, 8) combination with other CD method. (author)

  6. Effects of gas temperature in the plasma layer on RONS generation in array-type dielectric barrier discharge at atmospheric pressure

    Science.gov (United States)

    Yoon, Sung-Young; Yi, Changho; Eom, Sangheum; Park, Seungil; Kim, Seong Bong; Ryu, Seungmin; Yoo, Suk Jae

    2017-12-01

    In this work, we studied the control of plasma-produced species under a fixed gas composition (i.e., ambient air) in a 10 kHz-driven array-type dielectric barrier atmospheric-pressure plasma discharge. Instead of the gas composition, only the gas velocity was controlled. Thus, the plasma-maintenance cost was considerably lower than methods such as external N2 or O2 injection. The plasma-produced species were monitored using Fourier transformed infrared spectroscopy. The discharge properties were measured using a voltage probe, current probe, infrared camera, and optical emission spectroscopy. The results showed that the major plasma products largely depend on the gas temperature in the plasma discharge layer. The gas temperature in the plasma discharge layer was significantly different to the temperature of the ceramic adjacent to the plasma discharge layer, even in the small discharge power density of ˜15 W/cm2 or ˜100 W/cm3. Because the vibrational excitation of N2 was suppressed by the higher gas flow, the major plasma-produced species shifted from NOx in low flow to O3 in high flow.

  7. Study on discharge plasma in a cylindrical inertial electrostatic confinement fusion device

    Science.gov (United States)

    Buzarbaruah, N.; Dutta, N. J.; Borgohain, D.; Mohanty, S. R.; Bailung, H.

    2017-08-01

    Deuterium plasma has been produced in a cylindrical inertial electrostatic confinement fusion device using hot and cold cathode discharges and the plasma parameters are determined by employing an electrostatic probe. The plasma temperature and density are estimated at optimum experimental conditions and it is noted that the plasma temperature is 3 eV in the case of hot cathode discharge whereas 10 eV in the case of the cold cathode discharge. The plasma density as determined is two orders more in the case of the hot cathode discharge than the other. The probe is also used to observe the ion oscillation in the negative potential well that is formed in between the cathode grid and chamber (anode). The observation of spontaneous oscillation along with the harmonics has been reported.

  8. Dependence of MnOx Catalyst Position on Toluene Decomposition using Nanosecond Pulsed Discharge Plasma

    Science.gov (United States)

    Han, Junkai; Ogasawara, Akihiko; Wang, Jinlong; Wang, Douyan; Namihira, Takao; Sasaki, Mitsuru; Akiyama, Hidenori; Zhang, Pengyi; Kumamoto University Collaboration; Tsinghua University Collaboration

    2015-09-01

    Plasma catalysis, which combines advantages of high selectivity due to the catalysis and with fast ignition and response due to plasma technique, appears to be a promising technology to simultaneously resolve both efficiency and workability issues. In practice, a catalyst can be combined with NTP in two ways: by introducing the catalyst in the discharge zone (in-plasma catalytic reactor) or by placing the catalyst after the discharge zone (post-plasma catalytic reactor). This work aims to clarify combined effects by coupling MnOx catalyst with ns pulsed discharge system for decomposition of 100 ppm toluene utilizing three methods: plasma alone, in-plasma catalytic and post-plasma catalytic methods, in atmospheric pressure at room temperature. As the results, toluene removal ratio reached 100% at approximately 50 J/L under the in-plasma catalytic and post-plasma catalytic methods, while it was 70% under the plasma alone method. The concentrations of O3, HCOOH, and CO under the plasma alone method were higher compared with the in-plasma catalytic or post-plasma catalytic methods. CO2 selectivity under the post-plasma catalytic method was the highest of these three methods when toluene removal ratio exceeded 80%.

  9. Wind tunnel experiments on flow separation control of an Unmanned Air Vehicle by nanosecond discharge plasma aerodynamic actuation

    Science.gov (United States)

    Kang, Chen; Hua, Liang

    2016-02-01

    Plasma flow control (PFC) is a new kind of active flow control technology, which can improve the aerodynamic performances of aircrafts remarkably. The flow separation control of an unmanned air vehicle (UAV) by nanosecond discharge plasma aerodynamic actuation (NDPAA) is investigated experimentally in this paper. Experimental results show that the applied voltages for both the nanosecond discharge and the millisecond discharge are nearly the same, but the current for nanosecond discharge (30 A) is much bigger than that for millisecond discharge (0.1 A). The flow field induced by the NDPAA is similar to a shock wave upward, and has a maximal velocity of less than 0.5 m/s. Fast heating effect for nanosecond discharge induces shock waves in the quiescent air. The lasting time of the shock waves is about 80 μs and its spread velocity is nearly 380 m/s. By using the NDPAA, the flow separation on the suction side of the UAV can be totally suppressed and the critical stall angle of attack increases from 20° to 27° with a maximal lift coefficient increment of 11.24%. The flow separation can be suppressed when the discharge voltage is larger than the threshold value, and the optimum operation frequency for the NDPAA is the one which makes the Strouhal number equal one. The NDPAA is more effective than the millisecond discharge plasma aerodynamic actuation (MDPAA) in boundary layer flow control. The main mechanism for nanosecond discharge is shock effect. Shock effect is more effective in flow control than momentum effect in high speed flow control. Project supported by the National Natural Science Foundation of China (Grant Nos. 61503302, 51207169, and 51276197), the China Postdoctoral Science Foundation (Grant No. 2014M562446), and the Natural Science Foundation of Shaanxi Province, China (Grant No. 2015JM1001).

  10. Nanosecond Pulsed Discharge in Water without Bubbles: A Fundamental Study of Initiation, Propagation and Plasma Characteristics

    Science.gov (United States)

    Seepersad, Yohan

    The state of plasma is widely known as a gas-phase phenomenon, but plasma in liquids have also received significant attention over the last century. Generating plasma in liquids however is theoretically challenging, and this problem is often overcome via liquid-gas phase transition preceding the actual plasma formation. In this sense, plasma forms in gas bubbles in the liquid. Recent work at the Drexel Plasma Institute has shown that nanosecond pulsed electric fields can initiate plasma in liquids without any initial cavitation phase, at voltages below theoretical direct-ionization thresholds. This unique regime is poorly understood and does not fit into any current descriptive mechanisms. As with all new phenomena, a complete fundamental description is paramount to understanding its usefulness to practical applications. The primary goals of this research were to qualitatively and quantitatively understand the phenomenon of nanosecond pulsed discharge in liquids as a means to characterizing properties that may open up niche application possibilities. Analysis of the plasma was based on experimental results from non-invasive, sub-nanosecond time-resolved optical diagnostics, including direct imaging, transmission imaging (Schlieren and shadow), and optical emission spectroscopy. The physical characteristics of the plasma were studied as a function of variations in the electric field amplitude and polarity, liquid permittivity, and pulse duration. It was found that the plasma size and emission intensity was dependent on the permittivity of the liquid, as well as the voltage polarity, and the structure and dynamics were explained by a 'cold-lightning' mechanism. The under-breakdown dynamics at the liquid-electrode interface were investigated by transmission imaging to provide evidence for a novel mechanism for initiation based on the electrostriction. This mechanism was proposed by collaborators on the project and developed alongside the experimental work in this

  11. Effect of Inductive Coil Geometry on the Thrust Efficiency of a Microwave Assisted Discharge Inductive Plasma Accelerator

    Science.gov (United States)

    Hallock, Ashley; Polzin, Kurt; Emsellem, Gregory

    2012-01-01

    Pulsed inductive plasma thrusters [1-3] are spacecraft propulsion devices in which electrical energy is capacitively stored and then discharged through an inductive coil. The thruster is electrodeless, with a time-varying current in the coil interacting with a plasma covering the face of the coil to induce a plasma current. Propellant is accelerated and expelled at a high exhaust velocity (O(10-100 km/s)) by the Lorentz body force arising from the interaction of the magnetic field and the induced plasma current. While this class of thruster mitigates the life-limiting issues associated with electrode erosion, pulsed inductive plasma thrusters require high pulse energies to inductively ionize propellant. The Microwave Assisted Discharge Inductive Plasma Accelerator (MAD-IPA) [4, 5] is a pulsed inductive plasma thruster that addressees this issue by partially ionizing propellant inside a conical inductive coil via an electron cyclotron resonance (ECR) discharge. The ECR plasma is produced using microwaves and permanent magnets that are arranged to create a thin resonance region along the inner surface of the coil, restricting plasma formation, and in turn current sheet formation, to a region where the magnetic coupling between the plasma and the inductive coil is high. The use of a conical theta-pinch coil is under investigation. The conical geometry serves to provide neutral propellant containment and plasma plume focusing that is improved relative to the more common planar geometry of the Pulsed Inductive Thruster (PIT) [2, 3], however a conical coil imparts a direct radial acceleration of the current sheet that serves to rapidly decouple the propellant from the coil, limiting the direct axial electromagnetic acceleration in favor of an indirect acceleration mechanism that requires significant heating of the propellant within the volume bounded by the current sheet. In this paper, we describe thrust stand measurements performed to characterize the performance

  12. Development of a Time Synchronized CW-Laser Induced Fluorescence Measurement for Quasi-Periodic Oscillatory Plasma Discharges

    Science.gov (United States)

    MacDonald, Natalia; Cappelli, Mark; Hargus, William, Jr.

    2012-10-01

    An advanced CW laser induced fluorescence diagnostic technique, capable of correlating high frequency current fluctuations to the resulting fluorescence excitation lineshapes, has been developed. This presentation describes this so-called ``Sample-Hold'' method of time-synchronization, and provides the steps taken to validate this technique, including simulations and experimental measurements on a 60 Hz Xe lamp discharge. Initial results for time-synchronized velocity measurements on the quasi-periodic oscillatory mode of a magnetic cusped plasma accelerator are also presented. These results show that the positions of the ionization and peak acceleration regions in the device vary over the course of a discharge current oscillation.

  13. Long-Lived Plasma Process, Created by Impulse Discharge in Micro-Disperse Droplet Environment

    Directory of Open Access Journals (Sweden)

    Serge Olszewski

    2013-01-01

    Full Text Available The processes of organic compound (phenol and cation-active surfactants destruction in water solutions, which stay under the influence of plasma treatment have been investigated in different dynamic plasma-liquid systems (PLS with discharges in droplet micro-disperse environments (DMDE. The long-lived plasma process with separate spectral properties has been observed for pulsed discharge in DMDE. The approximate computer model is being proposed for a description of this effect. According to the introduced model this long-lived process is the aggregation of correlated discharges between charged droplets.

  14. Two-step ionization in non-equilibrium SF sub 6 discharges at high current density

    CERN Document Server

    Bychkov, Yu A; Lacour, B; Pasquiers, S; Puech, V; Yastremski, A

    2003-01-01

    In the pressure range 10-100 mbar, the discharge development in SF sub 6 has been investigated in the photo-triggered excitation scheme for current density in the range 10-1000 A cm sup - sup 2 and pulse duration of about 60 ns. Thanks to the homogeneity of the photo-triggered discharge, a self-consistent zero-dimensional model can be used to predict the temporal evolution of the electrical parameters. From a detailed comparison between the experimental results and the modelling predictions, evidence for the occurrence of a two-step ionization process in high current density discharges in SF sub 6 is reported and the corresponding collision cross-section is estimated. Moreover, it is shown that the amount of the two-step ionization is directly correlated to the density of the electrical charge transferred to the plasma per unit surface. This two-step ionization becomes the main source of electron multiplication whenever the transferred charge per unit surface is higher than 15 mu C cm sup - sup 2.

  15. Electron current extraction from radio frequency excited micro-dielectric barrier discharges

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Jun-Chieh; Kushner, Mark J. [Electrical Engineering and Computer Science Department, University of Michigan, 1301 Beal Ave., Ann Arbor, Michigan 48109 (United States); Leoni, Napoleon; Birecki, Henryk; Gila, Omer [Hewlett Packard Research Labs, Palo Alto, California 94304 (United States)

    2013-01-21

    Micro dielectric barrier discharges (mDBDs) consist of micro-plasma devices (10-100 {mu}m diameter) in which the electrodes are fully or partially covered by dielectrics, and often operate at atmospheric pressure driven with radio frequency (rf) waveforms. In certain applications, it may be desirable to extract electron current out of the mDBD plasma, which necessitates a third electrode. As a result, the physical structure of the m-DBD and the electron emitting properties of its materials are important to its operation. In this paper, results from a two-dimensional computer simulation of current extraction from mDBDs sustained in atmospheric pressure N{sub 2} will be discussed. The mDBDs are sandwich structures with an opening of tens-of-microns excited with rf voltage waveforms of up to 25 MHz. Following avalanche by electron impact ionization in the mDBD cavity, the plasma can be expelled from the cavity towards the extraction electrode during the part of the rf cycle when the extraction electrode appears anodic. The electron current extraction can be enhanced by biasing this electrode. The charge collection can be controlled by choice of rf frequency, rf driving voltage, and permittivity of the dielectric barrier.

  16. A study of the transient plasma potential in a pulsed bi-polar dc magnetron discharge

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, J W; Karkari, S K; Vetushka, A [Department of Physics, UMIST, Sackville Street, Manchester, M60 1QD (United Kingdom)

    2004-05-01

    The temporal evolution of the plasma potential, V{sub p}, in a pulsed dc magnetron plasma has been determined using the emissive probe technique. The discharge was operated in the 'asymmetric bi-polar' mode, in which the discharge voltage changes polarity during part of the pulse cycle. The probe measurements, with a time-resolution of 20 ns or better, were made along a line above the racetrack, normal to the plane of the cathode target, for a fixed frequency (100 kHz), duty cycle (50%), argon pressure (0.74 Pa) and discharge power (583 W). At all the measured positions, V{sub p} was found to respond to the large and rapid changes in the cathode voltage, V{sub d}, during the different phases of the pulse cycle, with V{sub p} always more positive than V{sub d}. At a typical substrate position (>80 mm from the target), V{sub p} remains a few volts above the most positive surface in the discharge at all times. In the 'on' phase of the pulse, the measurements show a significant axial electric field is generated in the plasma, with the plasma potential dropping by a total of about 30 V over a distance of 70 mm, from the bulk plasma to a position close to the beginning of the cathode fall. This is consistent with measurements made in the dc magnetron. During the stable 'reverse' phase of the discharge, for distances greater than 18 mm from the target, the axial electric field is found to collapse, with V{sub p} elevated uniformly to about 3 V above V{sub d}. Between the target and this field-free region an ion sheath forms, and the current flowing to the target is still an ion current in this 'reverse' period. During the initial 200 ns of the voltage 'overshoot' phase (between 'on' and 'reverse' phases), V{sub d} reached a potential of +290 V; however, close to the target, V{sub p} was found to attain a much higher value, namely +378 V. Along the line of measurement, the axial electric field reverses

  17. Effect of Electric Discharge on Properties of Nano-Particulate Catalyst for Plasma-Catalysis.

    Science.gov (United States)

    Lee, Chung Jun; Kim, Jip; Kim, Taegyu

    2016-02-01

    Heterogeneous catalytic processes have been used to produce hydrogen from hydrocarbons. However, high reforming temperature caused serious catalyst deteriorations and low energy efficiency. Recently, a plasma-catalyst hybrid process was used to reduce the reforming temperature and to improve the stability and durability of reforming catalysts. Effect of electric discharges on properties of nanoparticulate catalysts for plasma-catalysis was investigated in the present study. Catalyst-bed porosity was varied by packing catalyst beads with the different size in a reactor. Discharge power and onset voltage of the plasma were measured as the catalyst-bed porosity was varied. The effect of discharge voltage, frequency and voltage waveforms such as the sine, pulse and square was investigated. We found that the optimal porosity of the catalyst-bed exists to maximize the electric discharge. At a low porosity, the electric discharge was unstable to be sustained because the space between catalysts got narrow nearly close to the sheath region. On the other hand, at a high porosity, the electric discharge became weak because the plasma was not sufficient to interact with the surface of catalysts. The discharge power increased as the discharge voltage and frequency increased. The square waveform was more efficient than the sine and pulse one. At a high porosity, however, the effect of the voltage waveform was not considerable because the space between catalysts was too large for plasma to interact with the surface of catalysts.

  18. Measurement and analysis for optical radiation of glow discharge plasma at atmospheric pressure

    Science.gov (United States)

    Ren, Qinglei; Lin, Qi

    2006-02-01

    The optical radiation measurement and analysis to the glow discharge plasma at atmospheric pressure have been done in the paper. The low temperature plasma due to atmospheric pressure glow discharge (APGD) in air has been produced on the planar surface of designed electrode plate. The optical radiation spectra of the plasma produced in two kinds of electrode plats with different power values loaded have been measured and sampled with the minitype grating spectrograph system. The acquired spectra data are processed averagely and analyzed. The results of analysis indicate that the optical characteristic of the APGD plasma is related to the loaded power and layout of the electrode plate. This shows that it is feasible to describe the characteristic parameters of APGD plasma qualitatively and control the strength of the APGD plasma quantitatively by the obtained relationship, which provides a convenient approach for utilizing APGD plasma effectively and also establishes some foundation to investigate APGD plasma further.

  19. Simulation Tool for Dielectric Barrier Discharge Plasma Actuators at Atmospheric and Sub-Atmospheric Pressures Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Traditional approaches for active flow separation control using dielectric barrier discharge (DBD) plasma actuators are limited to relatively low-speed flows and...

  20. Discharge characteristics and dynamics of compressive plasma streams generated by a compact magnetoplasma compressor

    Energy Technology Data Exchange (ETDEWEB)

    Garkusha, I. E.; Tereshin, V. I.; Chebotarev, V. V.; Solyakov, D. G.; Petrov, Yu. V.; Ladygina, M. S.; Marchenko, A. K.; Staltsov, V. V.; Yelisyeyev, D. V. [National Academy of Sciences of Ukraine, Institute of Plasma Physics, National Science Center ' Kharkiv Institute of Physics and Technology,' (Ukraine)

    2011-11-15

    Results from experimental studies of a compact magnetoplasma compressor designed for operation with heavy gases are presented. The integral characteristics of the discharge and the energy contents and other parameters of the generated xenon plasma streams are determined.

  1. Surface Modification of Asymmetric Polysulfone/Polyethylene Glycol Membranes by DC Ar-Glow Discharge Plasma

    Directory of Open Access Journals (Sweden)

    Chalad Yuenyao

    2016-01-01

    Full Text Available Polysulfone/polyethylene glycol (PSF/PEG membranes were prepared by dry/wet phase inversion method. Effects of direct current glow discharge plasma using argon as working gas on morphological structures and gas separation properties of membranes were studied. Alteration of membrane characteristics were analyzed by various techniques like contact angle, scanning electron microscope, Fourier transform infrared spectroscopy, and dynamic mechanical thermal analysis. Gas separation properties were measured in terms of permeation and ideal O2/N2 selectivity. Results showed that hydrophilic and gas separation properties of PSF/PEG membranes increased by plasma surface modification. It was also shown that the dosage of PEG and plasma treatment affected the morphological structures and mechanical and gas separation properties. The macro voids and transmembrane structure disappeared with a little amount of PEG dosage. Pore size and mechanical strength tend to decrease with increasing PEG dosage up to 10 wt%. Glass transition temperature (Tg receded from 201.8 to 143.7°C for pure PSF and PSF/PEG with PEG dosage of 10 wt%. O2 and N2 gases permeation through the 10-minute plasma treated membranes tend to increase. However, the permeation strongly dispersed when treatment time was more extended.

  2. Cleaning of niobium surface by plasma of diffuse discharge at atmospheric pressure

    Science.gov (United States)

    Tarasenko, V. F.; Erofeev, M. V.; Shulepov, M. A.; Ripenko, V. S.

    2017-07-01

    Elements composition of niobium surface before and after plasma treatment by runaway electron preionized diffuse discharge was investigated in atmospheric pressure nitrogen flow by means of an Auger electron spectroscopy. Surface characterizations obtained from Auger spectra show that plasma treatment by diffuse discharge after exposure of 120000 pulses provides ultrafine surface cleaning from carbon contamination. Moreover, the surface free energy of the treated specimens increased up to 3 times, that improve its adhesion property.

  3. Generation of intense soft X-rays from capillary discharge plasmas

    Indian Academy of Sciences (India)

    At Laser Plasma Division, RRCAT, a program on high voltage capillary discharge had been started. The system consists of a 400 kV Marx bank, water line capacitor, spark gap and capillary chamber. The initial results of the emission of intense short soft X-ray pulses (5–10 ns) from the capillary discharge are reported.

  4. Diagnostics of the plasma series resonance effect in radio-frequency discharges

    Science.gov (United States)

    Schulze, J.; Kampschulte, T.; Luggenhölscher, D.; Czarnetzki, U.

    2007-10-01

    The intention of the paper is to give an example on how different plasma diagnostics can be combined in a synergistic way in order to investigate new physics. The link between the individual diagnostics has to be provided by theoretical concepts that predict certain relations between the different plasma parameters. The example chosen here is the effect of self-excited plasma series resonances in asymmetric capacitively coupled RF discharges. These resonance oscillations lead to high frequency current oscillations and are caused by a series resonance between the capacitive sheath and the effective inductance of the bulk which results from electron inertia. The non-linearity of the sheath is essential for the self-excitation of these oscillations. Laser spectroscopic electric field measurements, phase and space resolved optical emission spectroscopy, current, voltage, and Langmuir probe measurements are combined. The synergistic effect of these diagnostics in combination with a simple analytical model for the modification of the electron energy distribution function by electron beams yields information on cause and effect of electron heating and a better understanding of these fundamental phenomena.

  5. Nonlinear time-series analysis of current signal in cathodic contact glow discharge electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Allagui, Anis, E-mail: aallagui@sharjah.ac.ae; Abdelkareem, Mohammad Ali [Department of Sustainable and Renewable Energy Engineering, University of Sharjah, PO Box 27272, Sharjah (United Arab Emirates); Rojas, Andrea Espinel [Institut de Recherche en Communications et Cybernétique de Nantes, Ecole Centrale de Nantes, 44300 Nantes (France); Bonny, Talal; Elwakil, Ahmed S. [Department of Electrical and Computer Engineering, University of Sharjah, PO Box 27272, Sharjah (United Arab Emirates)

    2016-05-28

    In the standard two-electrode configuration employed in electrolytic process, when the control dc voltage is brought to a critical value, the system undergoes a transition from conventional electrolysis to contact glow discharge electrolysis (CGDE), which has also been referred to as liquid-submerged micro-plasma, glow discharge plasma electrolysis, electrode effect, electrolytic plasma, etc. The light-emitting process is associated with the development of an irregular and erratic current time-series which has been arbitrarily labelled as “random,” and thus dissuaded further research in this direction. Here, we examine the current time-series signals measured in cathodic CGDE configuration in a concentrated KOH solution at different dc bias voltages greater than the critical voltage. We show that the signals are, in fact, not random according to the NIST SP. 800-22 test suite definition. We also demonstrate that post-processing low-pass filtered sequences requires less time than the native as-measured sequences, suggesting a superposition of low frequency chaotic fluctuations and high frequency behaviors (which may be produced by more than one possible source of entropy). Using an array of nonlinear time-series analyses for dynamical systems, i.e., the computation of largest Lyapunov exponents and correlation dimensions, and re-construction of phase portraits, we found that low-pass filtered datasets undergo a transition from quasi-periodic to chaotic to quasi-hyper-chaotic behavior, and back again to chaos when the voltage controlling-parameter is increased. The high frequency part of the signals is discussed in terms of highly nonlinear turbulent motion developed around the working electrode.

  6. Numerical Simulation of Non-Equilibrium Plasma Discharge for High Speed Flow Control

    Science.gov (United States)

    Balasubramanian, Ramakrishnan; Anandhanarayanan, Karupannasamy; Krishnamurthy, Rajah; Chakraborty, Debasis

    2017-06-01

    Numerical simulation of hypersonic flow control using plasma discharge technique is carried out using an in-house developed code CERANS-TCNEQ. The study is aimed at demonstrating a proof of concept futuristic aerodynamic flow control device. The Kashiwa Hypersonic and High Temperature wind tunnel study of plasma discharge over a flat plate had been considered for numerical investigation. The 7-species, 18-reaction thermo-chemical non-equilibrium, two-temperature air-chemistry model due Park is used to model the weakly ionized flow. Plasma discharge is modeled as Joule heating source terms in both the translation-rotational and vibrational energy equations. Comparison of results for plasma discharge at Mach 7 over a flat plate with the reference data reveals that the present study is able to mimic the exact physics of complex flow such as formation of oblique shock wave ahead of the plasma discharge region with a resultant rise in surface pressure and vibrational temperature up to 7000 K demonstrating the use of non-equilibrium plasma discharge for flow control at hypersonic speeds.

  7. Gyrokinetic Analysis of the Current Ramp Phase of an ITER-like DIII-D Discharge

    Science.gov (United States)

    Bravenec, B.; Holland, C.; McKee, G. R.; Candy, J.; Görler, T.

    2016-10-01

    Being able to predict transport, especially electron, during the current ramp-up phase of a discharge is of great interest, especially for ITER. Here we present results, both linear and nonlinear, from the gyrokinetic codes GYRO, CGYRO, GS2, and GENE (a benchmarking effort) for a DIII-D discharge run with the ITER shape and normalized current, field and ramp rate. Preliminary results at the mid-radius (r / a = 0.6) and at the end of the current ramp from GENE are insignificant fluxes while CGYRO predicts only a finite electron energy flux. However, this flux is from fluctuations at the highest poloidal wave numbers of the simulations, implying that valid simulations may need to resolve the electron scales. These results plus linear analysis and nonlinear simulations at other times during the ramp and at other locations in the plasma will be presented. Supported by the US DOE under DE-FG02-08ER54978, DE-FG02-07ER54917, DE-FG02-89ER53296, DE-FC02-04ER54698.

  8. Physics of Collisional Plasmas Introduction to High-Frequency Discharges

    CERN Document Server

    Moisan, Michel

    2012-01-01

    The Physics of Collisional Plasmas deals with the plasma physics of interest to laboratory research and industrial applications, such as lighting, fabrication of microelectronics, destruction of greenhouse gases. Its emphasis is on explaining the physical mechanisms, rather than the detailed mathematical description and theoretical analysis. At the introductory level, it is important to convey the characteristic physical phenomena of plasmas, before addressing the ultimate formalism of kinetic theory, with its microscopic, statistical mechanics approach. To this aim, this text translates the physical phenomena into more tractable equations, using the hydrodynamic model; this considers the plasma as a fluid, in which the macroscopic physical parameters are the statistical averages of the microscopic (individual) parameters. This book is an introduction to the physics of collisional plasmas, as opposed to plasmas in space. It is intended for graduate students in physics and engineering . The first chapter intr...

  9. Glow discharge plasma in water: a green approach to enhancing ability of chitosan for dye removal.

    Science.gov (United States)

    Wen, Yuezhong; Shen, Chensi; Ni, Yanyan; Tong, Shaoping; Yu, Feng

    2012-01-30

    There is a need to explore effective and green approaches to enhancing the ability to use chitosan for contaminant removal for practical implementation of this technology. In the present study, glow discharge plasma (GDP), which has thus far been studied for degradation of contaminants, was used for the first time to pre-treat chitosan for dye removal in aqueous solution. The results show that the GDP treatment changed the morphology and crystallinity of chitosan particles, and the number of -CH(2) and -CH(3) groups in the chitosan samples increased. Various pretreatment parameters, including discharge current and time, played significant roles in the chitosan modification. It is observed that dye uptake in GDP-modified chitosan was faster than adsorption in untreated chitosan. The maximum adsorption by chitosan followed the order of untreated chitosanGDP current: 50 mA)GDP current: 120 mA), implying that the chitosan modified by GDP had a higher maximum adsorption capacity in comparison with the untreated chitosan. A possible mechanism is proposed. These results show that GDP may be an attractive pretreatment technology for environmental adsorption materials. Copyright © 2011 Elsevier B.V. All rights reserved.

  10. Parallel 3-D numerical simulation of dielectric barrier discharge plasma actuators

    Science.gov (United States)

    Houba, Tomas

    Dielectric barrier discharge plasma actuators have shown promise in a range of applications including flow control, sterilization and ozone generation. Developing numerical models of plasma actuators is of great importance, because a high-fidelity parallel numerical model allows new design configurations to be tested rapidly. Additionally, it provides a better understanding of the plasma actuator physics which is useful for further innovation. The physics of plasma actuators is studied numerically. A loosely coupled approach is utilized for the coupling of the plasma to the neutral fluid. The state of the art in numerical plasma modeling is advanced by the development of a parallel, three-dimensional, first-principles model with detailed air chemistry. The model incorporates 7 charged species and 18 reactions, along with a solution of the electron energy equation. To the author's knowledge, a parallel three-dimensional model of a gas discharge with a detailed air chemistry model and the solution of electron energy is unique. Three representative geometries are studied using the gas discharge model. The discharge of gas between two parallel electrodes is used to validate the air chemistry model developed for the gas discharge code. The gas discharge model is then applied to the discharge produced by placing a dc powered wire and grounded plate electrodes in a channel. Finally, a three-dimensional simulation of gas discharge produced by electrodes placed inside a riblet is carried out. The body force calculated with the gas discharge model is loosely coupled with a fluid model to predict the induced flow inside the riblet.

  11. Mechanism of Synthesis of Ultra-Long Single Wall Carbon Nanotubes in Arc Discharge Plasma

    Energy Technology Data Exchange (ETDEWEB)

    Keidar, Michael [George Washington University

    2013-06-23

    In this project fundamental issues related to synthesis of single wall carbon nanotubes (SWNTs), which is relationship between plasma parameters and SWNT characteristics were investigated. Given that among plasma-based techniques arc discharge stands out as very advantageous in several ways (fewer defects, high flexibility, longer lifetime) this techniques warrants attention from the plasma physics and plasma technology standpoint. Both experimental and theoretical investigations of the plasma and SWNTs synthesis were conducted. Experimental efforts focused on plasma diagnostics, measurements of nanostructures parameters, and nanoparticle characterization. Theoretical efforts focused to focus on multi-dimensional modeling of the arc discharge and single wall nanotube synthesis in arc plasmas. It was demonstrated in experiment and theoretically that controlling plasma parameters can affect nanostucture synthesis altering SWNT properties (length and diameter) and leading to synthesis of new structures such as a few-layer graphene. Among clearly identified parameters affecting synthesis are magnetic and electric fields. Knowledge of the plasma parameters and discharge characteristics is crucial for ability to control synthesis process by virtue of both magnetic and electric fields. New graduate course on plasma engineering was introduced into curriculum. 3 undergraduate students were attracted to the project and 3 graduate students (two are female) were involved in the project. Undergraduate student from Historically Black University was attracted and participated in the project during Summer 2010.

  12. Plasma characteristics of a high power helicon discharge

    Energy Technology Data Exchange (ETDEWEB)

    Ziemba, T; Euripides, P; Slough, J; Winglee, R; Giersch, L; Carscadden, J; Schnackenberg, T; Isley, S [Box 351310, University of Washington, Seattle WA, 98195 (United States)

    2006-08-01

    A new high power helicon (HPH) plasma system has been designed to provide input powers of several tens of kilowatts to produce a large area (0.5 m{sup 2}) of uniform high-density, of at least 5 x 10{sup 17} m{sup -3}, plasma downstream from the helicon coil. Axial and radial plasma characteristics show that the plasma is to a lesser extent created in and near the helicon coil and then is accelerated into the axial and equatorial regions. The bulk acceleration of the plasma is believed to be due to a coupling of the bulk of the electrons to the helicon field, which in turn transfers energy to the ions via ambipolar diffusion. The plasma beta is near unity a few centimetres away from the HPH system and Bdot measurements show {delta}B perturbations in the order of the vacuum magnetic field magnitude. In the equatorial region, a magnetic separatrix is seen to develop roughly at the mid-point between the helicon and chamber wall. The magnetic perturbation develops on the time scale of the plasma flow speed and upon the plasma reaching the chamber wall decays to the vacuum magnetic field configuration within 200 {mu}s.

  13. Evaluation of the potentials of humic acid removal in water by gas phase surface discharge plasma.

    Science.gov (United States)

    Wang, Tiecheng; Qu, Guangzhou; Ren, Jingyu; Yan, Qiuhe; Sun, Qiuhong; Liang, Dongli; Hu, Shibin

    2016-02-01

    Degradation of humic acid (HA), a predominant type of natural organic matter in ground water and surface waters, was conducted using a gas phase surface discharge plasma system. HA standard and two surface waters (Wetland, and Weihe River) were selected as the targets. The experimental results showed that about 90.9% of standard HA was smoothly removed within 40 min's discharge plasma treatment at discharge voltage 23.0 kV, and the removal process fitted the first-order kinetic model. Roles of some active species in HA removal were studied by evaluating the effects of solution pH and OH radical scavenger; and the results presented that O3 and OH radical played significant roles in HA removal. Scanning electron microscope (SEM) and FTIR analysis showed that HA surface topography and molecular structure were changed during discharge plasma process. The mineralization of HA was analyzed by UV-Vis spectrum, dissolved organic carbon (DOC), specific UV absorbance (SUVA), UV absorption ratios, and excitation-emission matrix (EEM) fluorescence. The formation of disinfection by-products during HA sample chlorination was also identified, and CHCl3 was detected as the main disinfection by-product, but discharge plasma treatment could suppress its formation to a certain extent. In addition, approximately 82.3% and 67.9% of UV254 were removed for the Weihe River water and the Wetland water after 40 min of discharge plasma treatment. Copyright © 2015 Elsevier Ltd. All rights reserved.

  14. Electron beam relaxation in a beam-plasma discharge in crossed fields

    Energy Technology Data Exchange (ETDEWEB)

    Gadeev, K.K.; Erastov, E.M.; Ivanov, A.A.; Muksunov, A.M.; Nikiforov, V.A.; Severnyj, V.V.; Khripunov, B.I.; Shapkin, V.V. (Gosudarstvennyj Komitet po Ispol' zovaniyu Atomnoj Ehnergii SSSR, Moscow. Inst. Atomnoj Ehnergii)

    Experimental investigation into production conditions of high- degree ionization plasma with an electron beam Usub(b)=5 kV, Isub(b)=0.7 A in crypton n/sub 0/=3x10/sup 12/ cm/sup -3/ in crossed electric and magnetic fields is stated. It is shown that resonance electric field can lead both to starting up of volume discharge-under these conditions electron beam power dissipation sharply increases, and discharge breakdown. Power dissipation increases when incresing magnetic field intensity from 8 to 12 kGs. Dependence of electron beam power dissipation on a longitudinal size of working volume has been investigated. A minimum length of the beam and gas interaction range, at which generation of volume discharge is still possible, has been determined. The data obtained can be useful during construction of a plasma centrifuge on the basis of beam-plasma discharge.

  15. Origins of ion energy distribution function (IEDF) in high power impulse magnetron sputtering (HIPIMS) plasma discharge

    Science.gov (United States)

    Hecimovic, A.; Burcalova, K.; Ehiasarian, A. P.

    2008-05-01

    The ion energy distribution function (IEDF) in high power impulse magnetron sputtering (HIPIMS) discharges was studied by plasma sampling energy-resolved mass spectroscopy. HIPIMS of chromium (Cr), titanium (Ti) and carbon (C) targets in argon (Ar) atmosphere was analysed. Singly and doubly charged ions of both the target and the gas were detected. Time-averaged IEDFs were measured for all detected ions at the substrate position at a distance of 150 mm from the target. The effects of target current and discharge pressure on the IEDF were investigated. Measurements were done at two pressures and for three peak discharge currents. The IEDF of both the target and the gas ions was found to comprise two Maxwellian distributions. Quantitative analysis of target IEDFs at a low pressure showed that the main peak had a lower average energy with an approximate value of EAV = 1 eV which is attributed to collisions with thermalized gas atoms and ions. The higher energy distribution has a tail extending up to 70 eV, which is assumed to originate from a Thompson distribution of sputtered metal atoms which, due to collisions, are thermalized and appear as a Maxwell distribution. The proportion of high energy IEDFs for metal ions increases monotonically as a function of Id. The effective ion temperature kBT, extracted from the main low energy peak, showed a weak dependence on peak current. The effective ion temperature extracted from the high energy tail showed a strong correlation with the change in Id. The IEDF at high pressure shows that a proportion of high energy IEDFs was very low and dominated by a low energy main peak. The gas IEDF at high pressure was completely thermalized. The metal-ion-to-gas-ion ratio was found to increase with Id and with the sputtering yield of the target material.

  16. Electron dynamics and plasma jet formation in a helium atmospheric pressure dielectric barrier discharge jet

    Energy Technology Data Exchange (ETDEWEB)

    Algwari, Q. Th. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); Electronic Department, College of Electronics Engineering, Mosul University, Mosul 41002 (Iraq); O' Connell, D. [Centre for Plasma Physics, School of Maths and Physics, Queen' s University Belfast, University Road, Belfast, Northern Ireland BT7 1NN (United Kingdom); York Plasma Institute, Department of Physics, University of York, York YO10 5DD (United Kingdom)

    2011-09-19

    The excitation dynamics within the main plasma production region and the plasma jets of a kHz atmospheric pressure dielectric barrier discharge (DBD) jet operated in helium was investigated. Within the dielectric tube, the plasma ignites as a streamer-type discharge. Plasma jets are emitted from both the powered and grounded electrode end; their dynamics are compared and contrasted. Ignition of these jets are quite different; the jet emitted from the powered electrode is ignited with a slight time delay to plasma ignition inside the dielectric tube, while breakdown of the jet at the grounded electrode end is from charging of the dielectric and is therefore dependent on plasma production and transport within the dielectric tube. Present streamer theories can explain these dynamics.

  17. Effect of Electron Energy Distribution on the Hysteresis of Plasma Discharge: Theory, Experiment, and Modeling

    Science.gov (United States)

    Lee, Hyo-Chang; Chung, Chin-Wook

    2016-09-01

    Hysteresis, which is the history dependence of physical systems, indicates that there are more-than-two stable points in a given condition, and it has been considered to one of the most important topics in fundamental physics. Recently, the hysteresis of plasma has become a focus of research because stable plasma operation is very important for fusion reactors, bio-medical plasmas, and industrial plasmas for nano-device fabrication process. Interestingly, the bi-stability characteristics of plasma with a huge hysteresis loop have been observed in inductive discharge plasmas Because hysteresis study in such plasmas can provide a universal understanding of plasma physics, many researchers have attempted experimental and theoretical studies. Despite long plasma research, how this plasma hysteresis occurs remains an unresolved question in plasma physics. Here, we report theory, experiment, and modeling of the hysteresis. It was found experimentally and theoretically that evolution of the electron energy distribution (EED) makes a strong plasma hysteresis. In Ramsauer and non-Ramsauer gas experiments, it was revealed that the plasma hysteresis is observed only at high pressure Ramsauer gas where the EED deviates considerably from a Maxwellian shape. This hysteresis was presented in the plasma balance model where the EED is considered. Because electrons in plasmas are usually not in a thermal equilibrium, this EED-effect can be regarded as a universal phenomenon in plasma physics. This research was partially supported by Korea Research Institute of Standard and Science.

  18. On production and asymmetric focusing of flat electron beams using rectangular capillary discharge plasmas

    Science.gov (United States)

    Bagdasarov, G. A.; Bobrova, N. A.; Boldarev, A. S.; Olkhovskaya, O. G.; Sasorov, P. V.; Gasilov, V. A.; Barber, S. K.; Bulanov, S. S.; Gonsalves, A. J.; Schroeder, C. B.; van Tilborg, J.; Esarey, E.; Leemans, W. P.; Levato, T.; Margarone, D.; Korn, G.; Kando, M.; Bulanov, S. V.

    2017-12-01

    A method for the asymmetric focusing of electron bunches, based on the active plasma lensing technique, is proposed. This method takes advantage of the strong inhomogeneous magnetic field generated inside the capillary discharge plasma to focus on the ultrarelativistic electrons. The plasma and magnetic field parameters inside the capillary discharge are described theoretically and modeled with dissipative magnetohydrodynamic computer simulations enabling analysis of the capillaries of rectangle cross-sections. Large aspect ratio rectangular capillaries might be used to transport electron beams with high emittance asymmetries, as well as assist in forming spatially flat electron bunches for final focusing before the interaction point.

  19. Growth Enhancement of Radish Sprouts Induced by Low Pressure O2 Radio Frequency Discharge Plasma Irradiation

    Science.gov (United States)

    Kitazaki, Satoshi; Koga, Kazunori; Shiratani, Masaharu; Hayashi, Nobuya

    2012-01-01

    We studied growth enhancement of radish sprouts (Raphanus sativus L.) induced by low pressure O2 radio frequency (RF) discharge plasma irradiation. The average length of radish sprouts cultivated for 7 days after O2 plasma irradiation is 30-60% greater than that without irradiation. O2 plasma irradiation does not affect seed germination. The experimental results reveal that oxygen related radicals strongly enhance growth, whereas ions and photons do not.

  20. Kinetics of Tomato Peroxidase Inactivation by Atmospheric Pressure Cold Plasma Based on Dielectric Barrier Discharge

    OpenAIRE

    Cullen, Patrick; Pankaj, Shashi; Misra, N

    2013-01-01

    Atmospheric pressure cold plasma technology is an emerging nonthermal food technology for microbiological decontamination of food and bio-materials. This study demonstrates the applicability of in-package cold plasma technology as a novel means to inactivation of enzymes. The kinetics of inactivation of tomato peroxidase as a model enzyme was studied at 30, 40 and 50kV, for up to 5’ of atmospheric air dielectric barrier discharge plasma treatments. The enzyme activity was found to decrease wi...

  1. Discharge Plasma Treatment for ${NO}_x$ Reduction from Diesel Engine Exhaust: A Laboratory Investigation

    OpenAIRE

    Rajanikanth, BS; Srinivasan, AD; Ravi, V

    2005-01-01

    A detailed study on the removal of oxides of nitrogen $({NO}_x)$ with and without the presence of carbonaceous soot in a stationary diesel engine exhaust was carried out using pulsed electrical discharges/catalyst/adsorbent processes. The processes were separately studied first and then the cascaded processes namely plasma-catalyst and plasma-adsorbent were examined. To investigate the effect of carbonaceous soot on the plasma treatment process, the filtered and unfiltered exhaust was treated...

  2. Atmospheric-pressure dielectric barrier discharge (DBD) in air : plasma characterisation for skin therapy

    OpenAIRE

    Rajasekaran, Priyadarshini

    2011-01-01

    A pulsed atmospheric-pressure dielectric barrier discharge (DBD) device operating in air is investigated for medical applications such as for skin disinfection and promotion of wound healing. The device ignites plasma on objects of high capacitance such as the human body and with grounded electrodes. Plasma parameters such as electron density and electron distribution function are determined. Plasma chemical kinetics is simulated and the production of biologically-useful molecules...

  3. Application of Surface Micro-Discharge plasma to spacecraft component decontamination

    Science.gov (United States)

    Shimizu, Satoshi; Barczyk, Simon; Rettberg, Petra; Shimizu, Tetsuji; Klaempfl, Tobias; Zimmermann, Julia; Weber, Peter; Morfill, Gregor; Thomas, Hubertus

    2013-09-01

    In the field of extinct or extant extraterrestrial life research on other planets and moons, the prevention of biological contamination through spaceprobes is one of the most important requirements, and its detailed conditions are defined by the COSPAR planetary protection policy. Currently, a dry heat microbial reduction (DHMR) method is the only applicable way to satisfy the demand, which could, however, damage the sophisticated components like integrated circuits. In this study, cold atmospheric plasma based on the Surface Micro-Discharge technology was investigated for inactivation of different types of bacteria and endospores as an alternative method. After 90 min of plasma gas exposure, 3-6 log reductions were observed for the vegetative bacteria Escherichia coliand Deinococcus radiodurans and several types of bacterial endospores - including Bacillus atrophaeus, B. safensis, B. megaterium, B. megaterium 2c1 and B. thuringiensis E24. Furthermore, the applicability of the system for spacecraft decontamination was checked by studying the inactivation homogeneity, the temperature at the area of interest and the effects of the plasma gas exposure on different materials. The authors would like to acknowledge the financial support from Deutches Zentrum fuer Luft- und Raumfahrt (FKZ 50 JR1005).

  4. Discharge electrode configuration effects on the performance of a plasma sparker

    Science.gov (United States)

    Pei, Yanliang; Zhang, Liancheng; Huang, Yifan; Yan, Hui; Zhu, Xinlei; Liu, Zhen; Yan, Keping

    2017-09-01

    A multi-electrode array is commonly applied in a plasma sparker to generate stable acoustic pulses. In this paper, the effects of the electrode configuration on the performance of a plasma sparker have been investigated. In terms of the load electrical characteristics, the electrode radius and distance have negligible influence on the electric characteristics, whereas a larger electrode number results in a smaller voltage and a larger current but has little effect on the load energy. Regarding the acoustic characteristics, both the expansion and collapse pulses can be increased by decreasing the electrode tip radius. the influence of the electrode number and electrode gap distance on the amplitude of the expansion pulse was found to be negligible. And the amplitude of the collapse pulse decreases significantly with increasing electrode number. Increasing the electrode number decreases the energy efficiency for intense bubble interactions, thus, a small electrode tip radius and a small electrode number are preferred for the design of a plasma sparker if the total discharge energy is given.

  5. Detection of accelerated particles from pulsed plasma discharge ...

    Indian Academy of Sciences (India)

    The ion beam of a Mather-type 23.25 J plasma focus device operated with air filling at 10 Torr was registered using CR-39 nuclear track detector. The irradiated samples were etched in NaOH solution at 70°C for 1 h. It is found here that plasma beam contains multi-components of microbeams. The individual track density of ...

  6. Transferred plasma jet from a dielectric barrier discharge for processing of poly(dimethylsiloxane) surfaces

    CERN Document Server

    Nascimento, Fellype do; Canesqui, Mara A; Moshkalev, Stanislav

    2016-01-01

    In this work we studied processing of poly(dimethylsiloxane) (PDMS) surfaces using dielectric barrier discharge (DBD) plasma in two different assemblies, one using the primary plasma jet obtained from a conventional DBD and the other using a DBD plasma jet transfer. The evolution of water contact angle (WCA) in function of plasma processing time and in function of aging time as well as the changes in the surface roughness of PDMS samples for both plasma treatments have been studied. We also compared vibrational and rotational temperatures for both plasmas and for the first time the vibrational temperature (T_vib) for the transferred plasma jet has been shown to be higher as compared with the primary jet. The increment in the T_vib value seems to be the main reason for the improvements in adhesion properties and surface wettability for the transferred plasma jet. Possible explanations for the increase in the vibrational temperature are presented.

  7. Optimizing pulsed current micro plasma arc welding parameters to ...

    African Journals Online (AJOL)

    This paper reveals the influences of pulsed current parameters namely peak current, back current, pulse and pulse width on the ultimate tensile strength of Micro Plasma Arc Welded Inconel 625 sheets. Mathematical model is developed to predict ultimate tensile strength of pulsed current micro plasma arc welded Inconel ...

  8. Influence of the gap size and dielectric constant of the packing on the plasma discharge in a packed bed dielectric barrier discharge reactor: a fluid modeling study

    Science.gov (United States)

    van Laer, Koen; Bogaerts, Annemie

    2016-09-01

    Packed bed dielectric barrier discharge (DBD) reactors have proven to be very useful sources of non-thermal plasma for a wide range of applications, of which the environmental applications have received most attention in recent years. Compared to an empty DBD reactor, a packing was introduced to either enhance the energy efficiency of the process, or, if the packing is catalytically active, steer the process towards a preferred end product. A wide range of geometries, bead sizes and bead materials have been tested experimentally in the past. However, since experimental diagnostics become more difficult with a packing present, a computational study is proposed to gain more insight. Using COMSOL's built in plasma module, a 2D axisymmetric fluid model is developed to study the influence of the gap size and the dielectric constant (ɛ) of the packing. Helium is used as discharge gas, at atmospheric pressure and room temperature. By decreasing the gas gap, the electric field strength is enhanced, resulting in a higher number of current peaks per half cycle of applied rf potential. Increasing ɛ also enhances the electric field strength. However, after a certain ɛ, its influence saturates. The electric field strength will no longer increase, leaving the discharge behavior unchanged.

  9. Determination of plasma displacement based on eddy current diagnostics for the Keda Torus eXperiment

    Science.gov (United States)

    Tu, Cui; Li, Hong; Liu, Adi; Li, Zichao; Zhang, Yuan; You, Wei; Tan, Mingsheng; Luo, Bing; Adil, Yolbarsop; Hu, Jintong; Wu, Yanqi; Yan, Wentan; Xie, Jinlin; Lan, Tao; Mao, Wenzhe; Ding, Weixing; Xiao, Chijin; Zhuang, Ge; Liu, Wandong

    2017-10-01

    The measurement of plasma displacement is one of the most basic diagnostic tools in the study of plasma equilibrium and control in a toroidal magnetic confinement configuration. During pulse discharge, the eddy current induced in the vacuum vessel and shell will produce an additional magnetic field at the plasma boundary, which will have a significant impact on the measurement of plasma displacement using magnetic probes. In the newly built Keda Torus eXperiment (KTX) reversed field pinch device, the eddy current in the composite shell can be obtained at a high spatial resolution. This device offers a new way to determine the plasma displacement for KTX through the multipole moment expansion of the eddy current, which can be obtained by unique probe arrays installed on the inner and outer surfaces of the composite shell. In an ideal conductor shell approximation, the method of multipole moment expansion of the poloidal eddy current for measuring the plasma displacement in toroidal coordinates, is more accurate than the previous method based on symmetrical magnetic probes, which yielded results in cylindrical coordinates. Through an analytical analysis of many current filaments and numerical simulations of the current distribution in toroidal coordinates, the scaling relation between the first moment of the eddy current and the center of gravity of the plasma current is obtained. In addition, the origin of the multipole moment expansion of the eddy current in KTX is retrieved simultaneously. Preliminary data on the plasma displacement have been collected using these two methods during short pulse discharges in the KTX device, and the results of the two methods are in reasonable agreement.

  10. Electric field formation in three different plasmas: A fusion reactor, arc discharge, and the ionosphere

    Science.gov (United States)

    Lee, Kwan Chul

    2017-11-01

    Three examples of electric field formation in the plasma are analyzed based on a new mechanism driven by ion-neutral collisions. The Gyro-Center Shift analysis uses the iteration of three equations including perpendicular current induced by the momentum exchange between ions and neutrals when there is asymmetry over the gyro-motion. This method includes non-zero divergence of current that leads the solution of time dependent state. The first example is radial electric field formation at the boundary of the nuclear fusion device, which is a key factor in the high-confinement mode operation of future fusion reactors. The second example is the reversed rotation of the arc discharge cathode spot, which has been a mysterious subject for more than one hundred years. The third example is electric field formations in the earth's ionosphere, which are important components of the equatorial electrojet and black aurora. The use of one method that explains various examples from different plasmas is reported, along with a discussion of the applications.

  11. Plasma Current Start-up in a Spherical Tokamak

    Science.gov (United States)

    Mitarai, Osamu; Kessel, Charles; Hirose, Akira

    The various plasma current start-up techniques and related topics in a spherical tokamak (ST) device are described. The Ohmic heating coil current clamp experiments in NSTX are described and discussed, and the plasma current start-up experiments in the STOR-M tokamak with iron core and the outer vertical field coil is presented as one of technique for a plasma current start-up in a ST.

  12. Differential Inactivation of Fungal Spores in Water and on Seeds by Ozone and Arc Discharge Plasma.

    Science.gov (United States)

    Kang, Min Ho; Pengkit, Anchalee; Choi, Kihong; Jeon, Seong Sil; Choi, Hyo Won; Shin, Dong Bum; Choi, Eun Ha; Uhm, Han Sup; Park, Gyungsoon

    2015-01-01

    Seed sterilization is essential for preventing seed borne fungal diseases. Sterilization tools based on physical technologies have recently received much attention. However, available information is very limited in terms of efficiency, safety, and mode of action. In this study, we have examined antifungal activity of ozone and arc discharge plasma, potential tools for seed sterilization. In our results, ozone and arc discharge plasma have shown differential antifungal effects, depending on the environment associated with fungal spores (freely submerged in water or infected seeds). Ozone inactivates Fusarium fujikuroi (fungus causing rice bakanae disease) spores submerged in water more efficiently than arc discharge plasma. However, fungal spores associated with or infecting rice seeds are more effectively deactivated by arc discharge plasma. ROS generated in water by ozone may function as a powerful fungicidal factor. On the other hand, shockwave generated from arc discharge plasma may have greatly contributed to antifungal effects on fungus associated with rice seeds. In support of this notion, addition of ultrasonic wave in ozone generating water has greatly increased the efficiency of seed disinfection.

  13. Differential Inactivation of Fungal Spores in Water and on Seeds by Ozone and Arc Discharge Plasma.

    Directory of Open Access Journals (Sweden)

    Min Ho Kang

    Full Text Available Seed sterilization is essential for preventing seed borne fungal diseases. Sterilization tools based on physical technologies have recently received much attention. However, available information is very limited in terms of efficiency, safety, and mode of action. In this study, we have examined antifungal activity of ozone and arc discharge plasma, potential tools for seed sterilization. In our results, ozone and arc discharge plasma have shown differential antifungal effects, depending on the environment associated with fungal spores (freely submerged in water or infected seeds. Ozone inactivates Fusarium fujikuroi (fungus causing rice bakanae disease spores submerged in water more efficiently than arc discharge plasma. However, fungal spores associated with or infecting rice seeds are more effectively deactivated by arc discharge plasma. ROS generated in water by ozone may function as a powerful fungicidal factor. On the other hand, shockwave generated from arc discharge plasma may have greatly contributed to antifungal effects on fungus associated with rice seeds. In support of this notion, addition of ultrasonic wave in ozone generating water has greatly increased the efficiency of seed disinfection.

  14. Plasma Perturbations in High-Speed Probing of Hall Thruster Discharge Chambers: Quantification and Mitigation

    Science.gov (United States)

    Jorns, Benjamin A.; Goebel, Dan M.; Hofer, Richard R.

    2015-01-01

    An experimental investigation is presented to quantify the effect of high-speed probing on the plasma parameters inside the discharge chamber of a 6-kW Hall thruster. Understanding the nature of these perturbations is of significant interest given the importance of accurate plasma measurements for characterizing thruster operation. An array of diagnostics including a high-speed camera and embedded wall probes is employed to examine in real time the changes in electron temperature and plasma potential induced by inserting a high-speed reciprocating Langmuir probe into the discharge chamber. It is found that the perturbations onset when the scanning probe is downstream of the electron temperature peak, and that along channel centerline, the perturbations are best characterized as a downstream shift of plasma parameters by 15-20% the length of the discharge chamber. A parametric study is performed to investigate techniques to mitigate the observed probe perturbations including varying probe speed, probe location, and operating conditions. It is found that the perturbations largely disappear when the thruster is operated at low power and low discharge voltage. The results of this mitigation study are discussed in the context of recommended methods for generating unperturbed measurements of the discharge chamber plasma.

  15. Positive direct current corona discharges in single wire-duct electrostatic precipitators

    OpenAIRE

    Ashraf Yehia; E. Abdel-Fattah; Akira Mizuno

    2016-01-01

    This paper is aimed to study the characteristics of the positive dc corona discharges in single wire-duct electrostatic precipitators. Therefore, the corona discharges were formed inside dry air fed single wire-duct reactor under positive dc voltage at the normal atmospheric conditions. The corona current-voltage characteristics curves have been measured in parallel with the ozone concentration generated inside the reactor under different discharge conditions. The corona current-voltage chara...

  16. Extreme Degree of Ionization in Homogenous Micro-Capillary Plasma Columns Heated by Ultrafast Current Pulses

    Science.gov (United States)

    Avaria, G.; Grisham, M.; Li, J.; Tomasel, F. G.; Shlyaptsev, V. N.; Busquet, M.; Woolston, M.; Rocca, J. J.

    2015-03-01

    Homogeneous plasma columns with ionization levels typical of megaampere discharges are created by rapidly heating gas-filled 520 -μ m -diameter channels with nanosecond rise time current pulses of 40 kA. Current densities of up to 0.3 GA cm-2 greatly increase Joule heating with respect to conventional capillary discharge Z pinches, reaching unprecedented degrees of ionization for a high-Z plasma column heated by a current pulse of remarkably low amplitude. Dense xenon plasmas are ionized to Xe28 + , while xenon impurities in hydrogen discharges reach Xe30 + . The unique characteristics of these hot, ˜300 :1 length-to-diameter aspect ratio plasmas allow the observation of unexpected spectroscopic phenomena. Axial spectra show the unusual dominance of the intercombination line over the resonance line of He-like Al by nearly an order of magnitude, caused by differences in opacities in the axial and radial directions. These plasma columns could enable the development of sub-10-nm x-ray lasers.

  17. Irregular-regular mode oscillations inside plasma bubble and its fractal analysis in glow discharge magnetized plasma

    Science.gov (United States)

    Megalingam, Mariammal; Hari Prakash, N.; Solomon, Infant; Sarma, Arun; Sarma, Bornali

    2017-04-01

    Experimental evidence of different kinds of oscillations in floating potential fluctuations of glow discharge magnetized plasma is being reported. A spherical gridded cage is inserted into the ambient plasma volume for creating plasma bubbles. Plasma is produced between a spherical mesh grid and chamber. The spherical mesh grid of 80% optical transparency is connected to the positive terminal of power supply and considered as anode. Two Langmuir probes are kept in the ambient plasma to measure the floating potential fluctuations in different positions within the system, viz., inside and outside the spherical mesh grid. At certain conditions of discharge voltage (Vd) and magnetic field, irregular to regular mode appears, and it shows chronological changes with respect to magnetic field. Further various nonlinear analyses such as Recurrence Plot, Hurst exponent, and Lyapunov exponent have been carried out to investigate the dynamics of oscillation at a range of discharge voltages and external magnetic fields. Determinism, entropy, and Lmax are important measures of Recurrence Quantification Analysis which indicate an irregular to regular transition in the dynamics of the fluctuations. Furthermore, behavior of the plasma oscillation is characterized by the technique called multifractal detrended fluctuation analysis to explore the nature of the fluctuations. It reveals that it has a multifractal nature and behaves as a long range correlated process.

  18. Three modes of a direct-current plasma jet operated underwater to degrade methylene blue

    Science.gov (United States)

    Xuechen, LI; Biao, WANG; Pengying, JIA; Linwei, YANG; Yaru, LI; Jingdi, CHU

    2017-11-01

    A direct-current air plasma jet operated underwater presents three stable modes including an intermittently-pulsed discharge, a periodically-pulsed discharge and a continuous discharge with increasing the power voltage. The three discharge modes have different appearances for the plasma plumes. Moreover, gap voltage-current characteristics indicate that the continuous discharge is in a normal glow regime. Spectral lines from reactive species (OH, N2, N2 +, H α , and O) have been revealed in the emission spectrum of the plasma jet operated underwater. Spectral intensities emitted from OH radical and oxygen atom increase with increasing the power voltage or the gas flow rate, indicating that reactive species are abundant. These reactive species cause the degradation of the methylene blue dye in solution. Effects of the experimental parameters such as the power voltage, the gas flow rate and the treatment time are investigated on the degradation efficiency. Results indicate that the degradation efficiency increases with increasing the power voltage, the gas flow rate or the treatment time. Compared with degradation in the intermittently-pulsed mode or the periodically-pulsed one, it is more efficient in the continuous mode, reaching 98% after 21 min treatment.

  19. Characterization of a dielectric barrier discharge in contact with liquid and producing a plasma activated water

    Science.gov (United States)

    Neretti, G.; Taglioli, M.; Colonna, G.; Borghi, C. A.

    2017-01-01

    In this work a low-temperature plasma source for the generation of plasma activated water (PAW) is developed and characterized. The plasma reactor was operated by means of an atmospheric-pressure air dielectric barrier discharge (DBD). The plasma generated is in contact with the water surface and is able to chemically activate the liquid medium. Electrodes were supplied by both sinusoidal and nanosecond-pulsed voltage waveforms. Treatment times were varied from 2 to 12 min to increase the energy dose released to the water by the DBD plasma. The physics of the discharge was studied by means of electrical, spectroscopic and imaging diagnostics. The interaction between the plasma and the liquid was investigated as well. Temperature and composition of the treated water were detected. Images of the discharges showed a filamentary behaviour in the sinusoidal case and a more homogeneous behaviour in the nanosecond-pulsed one. The images and the electrical measurements allowed to evaluate an average electron number density of about 4  ×  1019 and 6  ×  1017 m-3 for the sinusoidal and nanosecond-pulsed discharges respectively. Electron temperatures in the range of 2.1÷2.6 eV were measured by using spectroscopic diagnostics. Rotational temperatures in the range of 318-475 K were estimated by fitting synthetic spectra with the measured ones. Water temperature and pH level did not change significantly after the exposure to the DBD plasma. The production of ozone and hydrogen peroxide within the water was enhanced by increasing the plasma treatment time and the energy dose. Numerical simulations of the nanosecond-pulsed discharge were performed by using a self-consistent coupling of state-to-state kinetics of the air mixture with the Boltzmann equation of free electron kinetics. Temporal evolution of the electron energy distribution function shows departure from the Maxwellian distribution especially during the afterglow phase of the discharge. When

  20. Low pressure plasma discharges for the sterilization and decontamination of surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Rossi, F; Rauscher, H; Hasiwa, M; Gilliland, D [European Commission, Joint Research Centre, Institute for Health and Consumer Protection, Via E. Fermi 2749, 21027 Ispra (Vatican City State, Holy See) (Italy); Kylian, O [Faculty of Mathematics and Physics, Charles University, V Holesovickach 2, Prague 8, 180 00 (Czech Republic)], E-mail: francois.rossi@jrc.ec.europa.eu

    2009-11-15

    The mechanisms of sterilization and decontamination of surfaces are compared in direct and post discharge plasma treatments in two low-pressure reactors, microwave and inductively coupled plasma. It is shown that the removal of various biomolecules, such as proteins, pyrogens or peptides, can be obtained at high rates and low temperatures in the inductively coupled plasma (ICP) by using Ar/O{sub 2} mixtures. Similar efficiency is obtained for bacterial spores. Analysis of the discharge conditions illustrates the role of ion bombardment associated with O radicals, leading to a fast etching of organic matter. By contrast, the conditions obtained in the post discharge lead to much lower etching rates but also to a chemical modification of pyrogens, leading to their de-activation. The advantages of the two processes are discussed for the application to the practical case of decontamination of medical devices and reduction of hospital infections, illustrating the advantages and drawbacks of the two approaches.

  1. Plasma Medicine: Current Achievements and Future Prospects

    Science.gov (United States)

    Laroussi, Mounir

    2012-10-01

    Research on the biomedical applications of low temperature plasmas started with small scale experiments that were simply aimed at discovering what happens to biological cells when exposed to the chemically rich environment of plasma. These early experiments took place in the mid to late 1990s. As interest in this multidisciplinary field dramatically rose, various engineering and physics groups collaborated with biologists and medical experts to investigate the use of plasma technology as a basis for innovative medical approaches to cure various diseases. However, many questions concerning the fundamental mechanisms involved in cell-plasma interaction remained unanswered. As a result various workshops were organized to gather the diverse research community in the field of plasma medicine in order to have a fruitful exchange of ideas regarding the scientific challenges that needed to be surmounted to advance and expand the field's knowledge base. The present GEC workshop continues this important tradition of scientific cooperation since there is still a significant lack of understanding of many of the biochemical and molecular pathways that come into play when biological cells are exposed to plasmas. In this talk, first background information on the various plasma devices developed in our institute will be presented. This will be followed by a summary of our work on the effects of plasmas on prokaryotic and eukaryotic cells. The talk will be concluded by presenting our vision of the future of the field and an outline of the main challenges that need to be overcome if practical medical applications are to be achieved.

  2. Glow plasma jet - experimental study of a transferred atmospheric pressure glow discharge

    Energy Technology Data Exchange (ETDEWEB)

    Guerra-Mutis, Marlon H [Mares Oil Ltd., Instituto Colombiano del Petroleo (ICP) - ECOPETROL (Colombia); U, Carlos V Pelaez [Laboratorio de Control Magnetico de Fluidos, Instituto Colombiano del Petroleo (ICP) - ECOPETROL (Colombia); H, Rafael Cabanzo [Laboratorio de Espectroscopia Atomico-Molecular (LEAM) - UIS (Colombia)

    2003-05-01

    In this paper we present the experimental study of a glow plasma jet (GPJ) obtained from a transferred atmospheric pressure glow discharge (APGD) operating at 60 Hz. The characterization of the emission spectra for both electrical discharges is presented and the electrical circuit features for APGD generation are discussed. The potentiality of GPJ as a source of active species for depletion of contaminants in liquid hydrocarbon fractions is also established.

  3. Saturated Resin Ectopic Regeneration by Non-Thermal Dielectric Barrier Discharge Plasma

    OpenAIRE

    Chunjing Hao; Zehua Xiao; Di Xu; Chengbo Zhang; Jian Qiu; Kefu Liu

    2017-01-01

    Textile dyes are some of the most refractory organic compounds in the environment due to their complex and various structure. An integrated resin adsorption/Dielectric Barrier Discharge (DBD) plasma regeneration was proposed to treat the indigo carmine solution. It is the first time to report ectopic regeneration of the saturated resins by non-thermal Dielectric Barrier Discharge. The adsorption/desorption efficiency, surface functional groups, structural properties, regeneration efficiency, ...

  4. Volatile organic compounds (VOCs) removal in non-thermal plasma double dielectric barrier discharge reactor.

    Science.gov (United States)

    Mustafa, Muhammad Farooq; Fu, Xindi; Liu, Yanjun; Abbas, Yawar; Wang, Hongtao; Lu, Wenjing

    2018-04-05

    Non-thermal plasma (NTP) an emerging technology to treat volatile organic compounds (VOCs) present in unhygienic point source air streams. In present study, double dielectric barrier discharge (DDBD) reactors were used for the first time to evaluate the removal efficiency of VOCs mixture of different nature at constant experimental conditions (input power 16-65.8 W, VOCs mixture feeding rate 1-6 L/min, 100-101 ppm inlet concentration of individual VOC). Reactor A and B with discharge gap at 6 mm and 3 mm respectively, were used in current study. When treated at an input power of 53.7 W with gas feeding rate of 1 L/min in DDBD reactor A, removal efficiency of the VOCs were: tetrachloroethylene (100%), toluene (100%), trichloroethylene (100%), benzene (100%), ethyl acetate (100%) and carbon disulfide (88.30%); whereas in reactor B, the removal efficiency of all VOCs were 100%. Plasma-catalyst (Pt-Sn/Al 2 O 3 , BaTiO 3 and HZSM-5) synergistic effect on VOCs removal efficiency was also investigated. Highest removal efficiency i.e 100% was observed for each compound with BaTiO 3 and HZSM-5 at an input power 65.8 W. However, integrating NTP with BaTiO 3 and HZSM-5 leads to enhanced removal performance of VOCs mixture with high activity, increase in energy efficiency and suppression of unwanted byproducts. Copyright © 2018 Elsevier B.V. All rights reserved.

  5. Laser-induced optogalvanic signal oscillations in miniature neon glow discharge plasma.

    Science.gov (United States)

    Saini, V K

    2013-06-20

    Laser-induced optogalvanic (OG) signal oscillations detected in miniature neon glow discharge plasma are investigated using a discharge equivalent-circuit model. The damped oscillations in OG signal are generated when a pulsed dye laser is tuned to a specific neon transition (1s5→2p2) at 588.2 nm under the discharge conditions where dynamic resistance changes its sign. Penning ionization via quasi-resonant energy transfer collisions between neon gas atoms in metastable state and sputtered electrode atoms in ground state is discussed to explain the negative differential resistance properties of discharge plasma that are attributed to oscillations in the OG signal. The experimentally observed results are simulated by analyzing the behavior of an equivalent discharge-OG circuit. Good agreement between theoretically calculated and experimental results is observed. It is found that discharge plasma is more sensitive and less stable in close vicinity to dynamic resistance sign inversion, which can be useful for weak-optical-transition OG detection.

  6. Note: Arc discharge plasma source with plane segmented LaB6 cathode.

    Science.gov (United States)

    Akhmetov, T D; Davydenko, V I; Ivanov, A A; Kreter, A; Mishagin, V V; Savkin, V Ya; Shulzhenko, G I; Unterberg, B

    2016-05-01

    A plane cathode composed of close-packed hexagonal LaB6 (lanthanum hexaboride) segments is described. The 6 cm diameter circular cathode is heated by radiation from a graphite foil flat spiral. The cathode along with a hollow copper anode is used for the arc discharge plasma production in a newly developed linear plasma device. A separately powered coil located around the anode is used to change the magnetic field strength and geometry in the anode region. Different discharge regimes were realized using this coil.

  7. A compact, low cost Marx bank for generating capillary discharge plasmas

    Science.gov (United States)

    Dyson, A. E.; Thornton, C.; Hooker, S. M.

    2016-09-01

    We describe in detail a low power Compact Marx Bank (CMB) circuit that can provide 20 kV, 500 A pulses of approximately 100-200 ns duration. One application is the generation of capillary discharge plasmas of density ≈1018 cm-3 used in laser plasma accelerators. The CMB is triggered with a high speed solid state switch and gives a high voltage output pulse with a ns scale rise time into a 50 Ω load (coaxial cable) with 45 kV are demonstrated in air discharges.

  8. Self-consistent evolution of plasma discharge and electromagnetic fields in a microwave pulse compressor

    Science.gov (United States)

    Shlapakovski, A. S.; Beilin, L.; Hadas, Y.; Schamiloglu, E.; Krasik, Ya. E.

    2015-07-01

    Nanosecond-scale evolution of plasma and RF electromagnetic fields during the release of energy from a microwave pulse compressor with a plasma interference switch was investigated numerically using the code MAGIC. The plasma was simulated in the scope of the gas conductivity model in MAGIC. The compressor embodied an S-band cavity and H-plane waveguide tee with a shorted side arm filled with pressurized gas. In a simplified approach, the gas discharge was initiated by setting an external ionization rate in a layer crossing the side arm waveguide in the location of the electric field antinode. It was found that with increasing ionization rate, the microwave energy absorbed by the plasma in the first few nanoseconds increases, but the absorption for the whole duration of energy release, on the contrary, decreases. In a hybrid approach modeling laser ignition of the discharge, seed electrons were set around the electric field antinode. In this case, the plasma extends along the field forming a filament and the plasma density increases up to the level at which the electric field within the plasma decreases due to the skin effect. Then, the avalanche rate decreases but the density still rises until the microwave energy release begins and the electric field becomes insufficient to support the avalanche process. The extraction of the microwave pulse limits its own power by terminating the rise of the plasma density and filament length. For efficient extraction, a sufficiently long filament of dense plasma must have sufficient time to be formed.

  9. Modification of the Steel Surface Treated by a Volume Discharge Plasma in Nitrogen at Atmospheric Pressure

    Science.gov (United States)

    Erofeev, M. V.; Shulepov, M. A.; Ivanov, Yu. F.; Oskomov, K. V.; Tarasenko, V. F.

    2016-03-01

    Effect of volume discharge plasma initiated by an avalanche electron beam on the composition, structure, and properties of the surface steel layer is investigated. Voltage pulses with incident wave amplitude up to 30 kV, full width at half maximum of about 4 ns, and wave front of about 2.5 ns were applied to the gap with an inhomogeneous electric field. Changes indicating the hardening effect of the volume discharge initiated by an avalanche electron beam are revealed in St3-grade steel specimens treated by the discharge of this type.

  10. Effects of background gas on sulfur hexafluoride removal by atmospheric dielectric barrier discharge plasma

    Directory of Open Access Journals (Sweden)

    Xiaoxing Zhang

    2016-11-01

    Full Text Available The effects of background gases (He, Ar, N2 and air on SF6 removal in a dielectric barrier reactor were investigated at atmospheric pressure. A comparison among these background gases was performed in terms of discharge voltage, discharge power, mean electron energy, electron density, removal efficiency and energy yield for the destruction of SF6. Results showed that the discharge voltage of He and Ar was lower than that of N2 and air, but the difference of their discharge power was small. Compared with three other background gases, Ar had a relatively superior destruction and removal rate and energy yield since the mean electron energy and electron density in SF6/H2O/Ar plasma were both maintained at a high level. Complete removal of 2% SF6 could be achieved at a discharge power of 48.86 W with Ar and the corresponding energy yield can reach 4.8 g/kWh.

  11. A uniform laminar air plasma plume with large volume excited by an alternating current voltage

    Science.gov (United States)

    Li, Xuechen; Bao, Wenting; Chu, Jingdi; Zhang, Panpan; Jia, Pengying

    2015-12-01

    Using a plasma jet composed of two needle electrodes, a laminar plasma plume with large volume is generated in air through an alternating current voltage excitation. Based on high-speed photography, a train of filaments is observed to propagate periodically away from their birth place along the gas flow. The laminar plume is in fact a temporal superposition of the arched filament train. The filament consists of a negative glow near the real time cathode, a positive column near the real time anode, and a Faraday dark space between them. It has been found that the propagation velocity of the filament increases with increasing the gas flow rate. Furthermore, the filament lifetime tends to follow a normal distribution (Gaussian distribution). The most probable lifetime decreases with increasing the gas flow rate or decreasing the averaged peak voltage. Results also indicate that the real time peak current decreases and the real time peak voltage increases with the propagation of the filament along the gas flow. The voltage-current curve indicates that, in every discharge cycle, the filament evolves from a Townsend discharge to a glow one and then the discharge quenches. Characteristic regions including a negative glow, a Faraday dark space, and a positive column can be discerned from the discharge filament. Furthermore, the plasma parameters such as the electron density, the vibrational temperature and the gas temperature are investigated based on the optical spectrum emitted from the laminar plume.

  12. Eddy current-adjusted plasma shape reconstruction by Cauchy condition surface method on QUEST

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, K., E-mail: nakamura@triam.kyushu-u.ac.jp [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka (Japan); Jiang, Y.; Liu, X.L. [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, Kasuga, Fukuoka (Japan); Mitarai, O. [Liberal Arts Education Center, Kumamoto Campus, Tokai University, Toroku, Kumamoto (Japan); Kurihara, K.; Kawamata, Y.; Sueoka, M. [Japan Atomic Energy Agency, Naka, Ibaraki (Japan); Hasegawa, M.; Tokunaga, K.; Zushi, H.; Hanada, K.; Fujisawa, A.; Sakamoto, M.; Idei, H.; Kawasaki, S.; Nakashima, H.; Higashijima, A.; Araki, K. [Research Institute for Applied Mechanics, Kyushu University, Kasuga, Fukuoka (Japan)

    2011-10-15

    CCS (Cauchy Condition Surface) method is a numerical approach to reproduce plasma shape, which has good precision in conventional tokamaks. In order to apply it in plasma shape reproduction of ST (Spherical Tokamak), the calculation precision of the CCS method in a spherical tokamak CPD (Compact PWI experimental Device) (B{sub t} = 0.25 T, R = 0.3 m, a = 0.2 m) has been analyzed. The precision was confirmed also in ST and decided to be applied to a spherical tokamak QUEST (B{sub t} = 0.25 T, R = 0.68 m, a = 0.40 m).. In present stage from the magnetic measurement, it is known that the eddy current effect is large in QUEST experiment, and there are no special magnetic measurements for eddy current now, so some proper model should be selected to evaluate the eddy current effect. The eddy current density by not only CS (Center Solenoid) coil but also plasma current is calculated using EDDYCAL (JAEA). The eddy current magnitudes are taken as unknown variables and solved together with plasma shape reconstruction in ohmic discharge and ECCD (Electron Cyclotron Current Drive) discharge.

  13. Overview of current applications in plasma medicine

    Science.gov (United States)

    Ryan, Thomas P.; Stalder, Kenneth R.

    2017-02-01

    Plasma medicine is a rapidly growing field of treatment, with the number and type of medical applications growing annually, such as dentistry, cancer treatment, wound treatment, Antimicrobial (bacteria, biofilm, virus, fungus, prions), and surface sterilization. Work promoting muscle and blood vessel regeneration and osteointegration is being investigated. This review paper will cover the latest treatments using gas-based plasmas in medicine. Disinfection of water and new commercial systems will also be reviewed, as well as vaccine deactivation. With the rapid increase in new investigators, development of new devices and systems for treatment, and wider clinical applications, Plasma medicine is becoming a powerful tool in in the field of medicine. There are a wide range of Plasma sources that allows customization of the effect. These variations include frequency (DC to MHz), voltage capacity (kV), gas source (He, Ar; O2, N2, air, water vapor; combinations), direct/indirect target exposure, and water targets.

  14. Non-Uniform Plasma Discharges in Near Earth Space Environment and Ionosphere to Troposphere Responses

    Science.gov (United States)

    McCanney, J. M.

    2009-05-01

    Most earth weather and ionosphere-space environment coupling studies separate the problems into distinct groups. Heliosphere to solar wind - solar storm activity to ionospheric coupling - thermosphere and mid- altitude to the ionosphere and electrical effects such as elves and sprites and thunderstorms in another group - additionally mid and high latitude weather systems are many times separated also. The theoretical work here shows that not only are these areas coupled and related, but it also shows that without the constant electrical and resulting magnetic driving forces from space environments, earth would have little if no weather variability at all below the ionosphere. With only solar light energy as input, earth (and the other planets) would have little weather at all. The realization that extensive electrical activates occur in and above the troposphere, extending to the ionosphere and ultimately coupling to the magnetosphere have raised the theoretical and experimental questions regarding the sources of EMF which create the observed effects. The current work has identified 17 Local Electrical Batteries (LEBs), which provide the electrical EMF that can be linked to the observed effects the jet streams and lower atmospheric weather phenomenon. The path of the sources of EMF can be followed from the passing solar wind through "tunnels" that end in electrical currents that pass into the atmosphere via the ionosphere to storm cloud systems in the lower atmosphere. However the source of energy comes from localized plasma discharging of a non-uniform plasma environment that powers the electrical systems of the entire solar system. These are ultimately the sources of electrical energy that power the severe lower atmospheric storm systems such as westerly moving hurricanes at low latitudes and associated tornadoes. The connection is made theoretically with the solar wind that drives the 17 identified LEBs. The ultimate source of driving energy is the result of an

  15. Experiments of Discharge Guiding using Strongly and Weakly Ionized Plasma Channel produced by KrF Laser

    Science.gov (United States)

    Shimada, Yoshinori; Uchida, Shigeaki; Kawasaki, Zen-Ichiro; Yamanaka, Tatsuhiko; Takagi, Yasuhiro; Furuoka, Yoshihiro; Yamanaka, Chiyoe

    We have studied the feasibility of a hybrid discharge method (to guide the discharge with strongly and weakly ionized plasma channels) of a long guiding laser plasma channel. Charged particle densities in a weakly ionized plasma channel were measured as a function of the laser intensity. Critical condition of the weakly ionized plasma to guide an electrical streamer was determined. The electrical resistibility of plasma channel to generate the self-propagating streamer is smaller than 3.5 Ωm. The self-propagating streamer could heat the channel and leads to a main discharge.

  16. Plasma medicine—current state of research and medical application

    Science.gov (United States)

    Weltmann, K.-D.; von Woedtke, Th

    2017-01-01

    Plasma medicine means the direct application of cold atmospheric plasma (CAP) on or in the human body for therapeutic purposes. Further, the field interacts strongly with results gained for biological decontamination. Experimental research as well as first practical application is realized using two basic principles of CAP sources: dielectric barrier discharges (DBD) and atmospheric pressure plasma jets (APPJ). Originating from the fundamental insights that the biological effects of CAP are most probably caused by changes of the liquid environment of cells, and are dominated by reactive oxygen and nitrogen species (ROS, RNS), basic mechanisms of biological plasma activity are identified. It was demonstrated that there is no increased risk of cold plasma application and, above all, there are no indications for genotoxic effects. The most important biological effects of cold atmospheric pressure plasma were identified: (1) inactivation of a broad spectrum of microorganisms including multidrug resistant ones; (2) stimulation of cell proliferation and tissue regeneration with lower plasma treatment intensity (treatment time); (3) inactivation of cells by initialization of programmed cell death (apoptosis) with higher plasma treatment intensity (treatment time). In recent years, the main focus of clinical applications was in the field of wound healing and treatment of infective skin diseases. First CAP sources are CE-certified as medical devices now which is the main precondition to start the introduction of plasma medicine into clinical reality. Plasma application in dentistry and, above all, CAP use for cancer treatment are becoming more and more important research fields in plasma medicine. A further in-depth knowledge of control and adaptation of plasma parameters and plasma geometries is needed to obtain suitable and reliable plasma sources for the different therapeutic indications and to open up new fields of medical application.

  17. Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis.

    Science.gov (United States)

    Raniszewski, Grzegorz; Wiak, Slawomir; Pietrzak, Lukasz; Szymanski, Lukasz; Kolacinski, Zbigniew

    2017-02-23

    One of the most common methods of carbon nanotubes (CNTs) synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon-plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs). It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented.

  18. Influence of Plasma Jet Temperature Profiles in Arc Discharge Methods of Carbon Nanotubes Synthesis

    Directory of Open Access Journals (Sweden)

    Grzegorz Raniszewski

    2017-02-01

    Full Text Available One of the most common methods of carbon nanotubes (CNTs synthesis is application of an electric-arc plasma. However, the final product in the form of cathode deposit is composed of carbon nanotubes and a variety of carbon impurities. An assay of carbon nanotubes produced in arc discharge systems available on the market shows that commercial cathode deposits contain about 10% CNTs. Given that the quality of the final product depends on carbon–plasma jet parameters, it is possible to increase the yield of the synthesis by plasma jet control. Most of the carbon nanotubes are multiwall carbon nanotubes (MWCNTs. It was observed that the addition of catalysts significantly changes the plasma composition, effective ionization potential, the arc channel conductance, and in effect temperature of the arc and carbon elements flux. This paper focuses on the influence of metal components on plasma-jet forming containing carbon nanotubes cathode deposit. The plasma jet temperature control system is presented.

  19. Excitation of a global plasma mode by an intense electron beam in a dc discharge

    Science.gov (United States)

    Sydorenko, D.; Kaganovich, I. D.; Ventzek, P. L. G.; Chen, L.

    2018-01-01

    The interaction of an intense electron beam with a finite-length, inhomogeneous plasma is investigated numerically. The plasma density profile is maximal in the middle and decays towards the plasma edges. Two regimes of the two-stream instability are observed. In one regime, the frequency of the instability is the plasma frequency at the density maximum and plasma waves are excited in the middle of the plasma. In the other regime, the frequency of the instability matches the local plasma frequency near the edges of the plasma and the intense plasma oscillations occur near plasma boundaries. The latter regime appears sporadically and only for strong electron beam currents. This instability generates a copious amount of suprathermal electrons. The energy transfer to suprathermal electrons is the saturation mechanism of the instability.

  20. Current self-limitation in a transverse nanosecond discharge with a slotted cathode

    Science.gov (United States)

    Ashurbekov, N. A.; Iminov, K. O.; Popov, O. A.; Shakhsinov, G. S.

    2017-03-01

    A high-voltage transverse pulsed nanosecond discharge with a slotted hollow cathode was found to be a source of high-energy (few kV) ribbon electron beams. Conditions for the formation and extinction of electron beams were experimentally studied in discharges in helium at pressures of 1-100 Torr. It was found that interaction of fast electrons with a non-uniform electric field near the slotted cathode led to limitation of the magnitude of the discharge current. A physical model was developed to describe the discharge current self-limitation that was in satisfactory agreement with the experimental results. Some technical solutions that are expected to increase the upper current limits in transverse nanosecond discharge are discussed.

  1. Discharge ignition behavior of the Space Station plasma contactor

    Science.gov (United States)

    Sarver-Verhey, Timothy R.; Hamley, John A.

    1995-01-01

    Ignition testing of hollow cathode assemblies being developed for the Space Station plasma contactor system has been initiated to validate reliable multiple restart capability. An ignition approach was implemented that was derived from an earlier arcjet program that successfully demonstrated over 11,600 ignitions. For this, a test profile was developed to allow accelerated cyclic testing at expected operating conditions. To date, one hollow cathode assembly has been used to demonstrate multiple ignitions. A prototype hollow cathode assembly has achieved 3,615 successful ignitions at a nominal anode voltage of 18.0 V. During the ignition testing several parameters were investigated, of which the heater power and pre-heat time were the only parameters found to significantly impact ignition rate.

  2. Validation of numerical codes for the analysis of plasma discharges

    Energy Technology Data Exchange (ETDEWEB)

    Albanese, R. (Univ. di Salerno, Dipt. di Ingegneria Elettronica, Fisciano (Italy)); Bottura, L. (NET Team, Garching (Germany)); Chiocchio, S. (NET Team, Garching (Germany)); Coccorese, E. (Univ. di Reggio Calabria, Ist. di Ingegneria Elettronica (Italy)); Gernhardt, J. (Max Planck IPP, Garching (Germany)); Gruber, O. (Max Planck IPP, Garching (Germany)); Fresa, R. (Univ. di Salerno, Dipt. di Ingegneria Elettronica, Fisciano (Italy)); Martone, R. (Univ. di Salerno, Dipt. di Ingegneria Elettronica, Fisciano (Italy)); Portone, A. (NET Team, Garching (Germany)); Seidel, U. (Max Planck IPP, Garching (Germany))

    1994-01-01

    Electromagnetic aspects in the design of ITER-like reactors call for an extensive use of complex and advanced numerical codes. For this reason a strong attention has been paid within the NET-Team to the code development. In particular, through a cooperation with some Italian universities, during the last years a number of numerical procedures were developed and integrated. In order to assess the code reliability and to gain confidence on their predictions for next generation ITER-like reactors, the validation of the codes against experiments has to be considered as a strict requirement. Aim of this paper is to give a comprehensive presentation of this problem in the light of the results of a campaign of validation runs. The main outcome of this work is that the computational procedures, which have been developed for the NET project and then extensively used also for ITER studies, can be considered as experimentally validated in a sufficiently wide range of cases of interest. In particular, computed values are compared with experimental measurements made during some typical ASDEX-Upgrade discharges. From the electromagnetic point of view, many features of this machine are common to the ITER concept, so that the results of the validation can reasonably be extended to the ITER case. (orig.)

  3. Removal Dynamics of Nitric Oxide (NO Pollutant Gas by Pulse-Discharged Plasma Technique

    Directory of Open Access Journals (Sweden)

    Lianshui Zhang

    2014-01-01

    Full Text Available Nonthermal plasma technique has drawn extensive attentions for removal of air pollutants such as NOx and SO2. The NO removal mechanism in pulse discharged plasma is discussed in this paper. Emission spectra diagnosis indicates that the higher the discharge voltage is, the more the NO are removed and transformed into O, N, N2, NO2, and so forth. Plasma electron temperature Te is ranged from 6400 K at 2.4 kV discharge voltage to 9500 K at 4.8 kV. After establishing a zero-dimensional chemical reaction kinetic model, the major reaction paths are clarified as the electron collision dissociation of NO into N and O during discharge and followed by single substitution of N on NO to form N2 during and after discharge, compared with the small fraction of NO2 formed by oxidizing NO. The reaction directions can be adjusted by N2 additive, and the optimal N2/NO mixing ratio is 2 : 1. Such a ratio not only compensates the disadvantage of electron competitive consumption by the mixed N2, but also heightens the total NO removal extent through accelerating the NO oxidization process.

  4. Modeling plasma glow discharges in Air near a Mach 3 bow shock with KRONOS

    Science.gov (United States)

    Rassou, Sebastien; Labaune, Julien; Packan, Denis; Elias, Paul-Quentin

    2016-09-01

    In this work, plasma glow discharge in Air is modeled near a Mach 3 bow shock. Numerical simulations are performed using the coupling KRONOS which have been developed at ONERA. The flow field is modeled using the code CFD: CEDRE from ONERA and the electrical and plasma part by the EDF open-source code CODE_SATURNE. The plasma kinetic modeling consists on a two-term Boltzmann equation solver and a chemical reaction solver depending of the electric field. The coupling KRONOS is fully parallelized and run on ONERA supercomputers. The shock wave is formed by the propagation of a supersonic flow (M = 3) through a truncated conical model mounted with a central spike. Depending on the spike's voltage value, corona, glow or arc regime could be obtained in a steady flow. The parameters for the supersonic flow and the spike configurations are chosen to be in glow discharge regime and to reproduce the experimental setup. In our simulations, 12 species and 80 reactions (ionization, electronic or vibrational excitation, attachment etc ...) are considered to properly model the glow discharge and the afterglow. In a stationary flow, glow discharge is observed only at the upstream of the shock wave near the high voltage spike. Behind the bow shock, in the afterglow, negative ions are provided by electrons attachment with O2. The negative ions flow convection ensures the electrical conduction and the establishment of the glow discharge.

  5. Experimental Studies of Coaxial Plasma Gun Current

    Science.gov (United States)

    1988-09-01

    insertion into experimental systems (117-133), fueling for proposed thermonuclear reactors (134-138], breeding fissionable material [139, 140] and...Center Top Level Linear Exponential Yield Current Current Extrap . Extrap . (MA) (MA) Current Current (MA) (MA) 02901 2.8106 0.18 0.05 D3001 1.2x107...Exponential Yield Current Current Extrap . Extrap . (MA) (MA) Current Current (MA) (MA) 30703 1.610 8 1.57 0.64 0.54 0.59 J0706 4.040O 1.46 0.85 0.80 0.82 J

  6. Recombination time of an RF discharge plasma in the presence of water molecules

    Energy Technology Data Exchange (ETDEWEB)

    Protasevich, E.T.

    1986-05-01

    The authors show that the introduction of water vapor into an electrodeless rf discharge noticeably reduces the excitation temperature and substantially increases the recombination time of the plasma. An attempt is made to explain the physical processes associated with these phenomena.

  7. Energy deposition characteristics of nanosecond dielectric barrier discharge plasma actuators : Influence of dielectric material

    NARCIS (Netherlands)

    Correale, G.; Winkel, R.; Kotsonis, M.

    2015-01-01

    An experimental study aimed at the characterization of energy deposition of nanosecond Dielectric Barrier Discharge (ns-DBD) plasma actuators was carried out. Special attention was given on the effect of the thickness and material used for dielectric barrier. The selected materials for this study

  8. Characterization of ion emission of an extreme ultraviolet generating discharge produced Sn plasma

    NARCIS (Netherlands)

    Gielissen, K.; Sidelnikov, Y.; Glushkov, D.; Soer, W.A.; Banine V.Y.; Van der Mullen, J.

    2010-01-01

    The ion emission of a Sn-based discharge produced extreme ultraviolet producing plasma is characterized with the combined use of different time-of-flight techniques. An electrostatic ion spectrometer isemployed to measure the average charge distribution of the emitted Sn ions. A dedicated Faraday

  9. Group Velocity Measurements in Laser-Heated Capillary Discharge Waveguides for Laser-Plasma Accelerators

    Science.gov (United States)

    Pieronek, C. V.; Daniels, J.; Gonsalves, A. J.; Benedetti, C.; Leemans, W. P.

    2017-10-01

    To date, the most energetic electron beams from laser-plasma accelerators have been produced using gas-filled capillary discharge waveguides, which increase the acceleration length by mitigating diffraction of the driving laser pulse. To reach higher electron beam energies, lower plasma density is required to reduce bunch dephasing. However, confinement of the driver is reduced for lower plasma density, reducing the acceleration length. A laser-heated capillary discharge waveguide, where the discharge is heated by a coaxial laser pulse, was proposed to create a steeper density gradient at lower density. Here the first measurements of group velocity in laser-heated capillary discharges, obtained via spectral interferometry, are presented. Increase of the driver group velocity and reduction in on-axis plasma density by laser-heating are shown. Work supported by the U.S. Dept. of Energy, Office of Science, Office of High Energy Physics, under Contract No. DE-AC02-05CH11231. Additional support by the National Science Foundation under Grant PHY-1415596.

  10. Method of preparing water purification membranes. [polymerization of allyl amine as thin films in plasma discharge

    Science.gov (United States)

    Hollahan, J. R.; Wydeven, T. J., Jr. (Inventor)

    1974-01-01

    Allyl amine and chemically related compounds are polymerized as thin films in the presence of a plasma discharge. The monomer compound can be polymerized by itself or in the presence of an additive gas to promote polymerization and act as a carrier. The polymerized films thus produced show outstanding advantages when used as reverse osmosis membranes.

  11. Charging of dust grains in a nonequilibrium plasma of a stratified glow discharge

    Science.gov (United States)

    Sukhinin, G. I.; Fedoseev, A. V.

    2007-12-01

    A theoretical model is presented that describes the charging of dust grains in the positive plasma column of a stratified glow dc discharge in argon. A one-dimensional self-consistent model is used to obtain axial profiles of the electric field, as well as the electron energy distribution function along the axis of the discharge tube. Radial profiles of the electric field are determined in the ambipolar diffusion approximation. It is assumed that, in the radial direction, the electron distribution function depends only on the total electron energy. Two-dimensional distributions of the discharge plasma parameters are calculated and used to determine the potential and charge of a test dust grain at a certain point within the discharge and the electrostatic forces acting on it. It is shown that the grain charge distribution depends strongly on the nonequilibrium electron distribution function and on the nonuniform distribution of the electric field in a stratified glow discharge. A discussion is presented on the suspension of dust grains, the separation of grains by size in the discharge striations, and a possible mechanism for the onset of vortex dust motion at the edge of a dust cloud.

  12. Experimental study of n-decane decomposition with microsecond pulsed discharge plasma

    Science.gov (United States)

    Feilong, SONG; Di, JIN; Min, JIA; Wenwen, WEI; Huimin, SONG; Yun, WU

    2017-12-01

    A highly-integrated experimental system for the plasma decomposition of fuels was built. Experiments were conducted in a flow reactor at atmospheric pressure and confirmed that n-decane could be cracked by large-gap dielectric barrier discharge under the excitation of a microsecond-pulse power supply. Alkanes and olefins with a C atom number that is smaller than 10 as well as hydrogen were found in the cracked products of n-decane (n-C10H22). The combination of preheating and plasma decomposition had strong selectivity for olefins. Under strong discharge conditions, small molecule olefins were found in the products. Moreover, there was a general tendency that small molecule olefins gradually accounted for higher percentage of products at higher temperature and discharge frequency.

  13. An overview of CO2 conversion in a microwave discharge: the role of plasma-catalysis

    Science.gov (United States)

    Chen, Guoxing; Britun, Nikolay; Godfroid, Thomas; Georgieva, Violeta; Snyders, Rony; Delplancke-Ogletree, Marie-Paule

    2017-03-01

    An overview of the recent progress on plasma-assisted CO2 conversion in microwave discharges is given. Special attention is devoted to the results obtained using plasma catalysis, which are compared to the plasma-only CO2 decomposition cases. The effects of plasma operating conditions, catalyst preparation methods, nature of plasma activation gas, gas mixture, as well as the NiO content on the TiO2 surface on CO2 conversion and its energy efficiency are discussed. A significant improvement in CO2 conversion is obtained with a NiO/TiO2 catalyst activated in Ar plasma, when the NiO content is about 10 wt.%. The catalyst characterization data show that Ar plasma treatment results in a higher density of oxygen vacancies and a comparatively more uniform distribution of NiO on the TiO2 surface, which strongly influence CO2 conversion and its energy efficiency. The dissociative electron attachment of CO2 at the catalyst surface enhanced by the oxygen vacancies and by plasma electrons may also explain the increase in conversion and energy efficiencies. A mechanism for the plasma-catalytic CO2 conversion at the surface of an Ar plasma-threated catalyst is proposed.

  14. Non-thermal dielectric-barrier discharge plasma damages human keratinocytes by inducing oxidative stress

    Science.gov (United States)

    KIM, KI CHEON; PIAO, MEI JING; HEWAGE, SUSARA RUWAN KUMARA MADDUMA; HAN, XIA; KANG, KYOUNG AH; JO, JIN OH; MOK, YOUNG SUN; SHIN, JENNIFER H.; PARK, YEUNSOO; YOO, SUK JAE; HYUN, JIN WON

    2016-01-01

    The aim of this study was to identify the mechanisms through which dielectric-barrier discharge plasma damages human keratinocytes (HaCaT cells) through the induction of oxidative stress. For this purpose, the cells were exposed to surface dielectric-barrier discharge plasma in 70% oxygen and 30% argon. We noted that cell viability was decreased following exposure of the cells to plasma in a time-dependent manner, as shown by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide assay. The levels of intracellular reactive oxygen species (ROS) were determined using 2′,7′-dichlorodihydro-fluorescein diacetate and dihydroethidium was used to monitor superoxide anion production. Plasma induced the generation of ROS, including superoxide anions, hydrogen peroxide and hydroxyl radicals. N-acetyl cysteine, which is an antioxidant, prevented the decrease in cell viability caused by exposure to plasma. ROS generated by exposure to plasma resulted in damage to various cellular components, including lipid membrane peroxidation, DNA breaks and protein carbonylation, which was detected by measuring the levels of 8-isoprostane and diphenyl-1-pyrenylphosphine assay, comet assay and protein carbonyl formation. These results suggest that plasma exerts cytotoxic effects by causing oxidative stress-induced damage to cellular components. PMID:26573561

  15. Generation of C6+ in a spark-discharge coupled laser plasma

    Science.gov (United States)

    Balki, Oguzhan; Rahman, Md. Mahmudur; Xiao, Shu; Elsayed-Ali, Hani E.

    2017-11-01

    By coupling a spark discharge into a laser-generated carbon plasma, fully-stripped carbon ions with a relatively low laser pulse energy are observed. When spark-discharge energy of ∼ 750 mJ is coupled to the carbon plasma generated by ∼ 50 mJ laser pulse (wavelength 1064 nm, pulse width 8 ns, intensity 5 × 109 W /cm2), enhancement in the total ion charge by a factor of ∼ 6 is observed, along with the increase of maximum charge state from C4+ to C6+. Spark coupling to the laser plasma significantly reduces the laser pulse energy required to generate highly-charged ions. Compared to the laser carbon plasma alone, the spark discharge increases the intensity of the spectral emission of carbon lines, the electron density ne, and the electron temperature Te. The effective ion plasma temperature associated with translational motion along the plume axis Tieff is calculated from the ion time-of-flight signal.

  16. High-speed sterilization technique using dielectric barrier discharge plasmas in atmospheric humid air

    Science.gov (United States)

    Miyamae, M.; Kikuchi, Y.; Fukumoto, N.; Nagata, M.

    2010-11-01

    The inactivation of Bacillus atrophaeus spores by a dielectric barrier discharge (DBD) plasma produced by an ac voltage application of 1 kHz in atmospheric humid air was investigated in order to develop low-temperature, low-cost and high-speed plasma sterilization technique. The biological indicators covered with a Tyvek sheet were set just outside the DBD plasma region, where the air temperature and humidity as a discharge gas were precisely controlled by an environmental test chamber. The results show that the inactivation of Bacillus atrophaeus spores was found to be dependent strongly on the humidity, and was completed within 15 min at a relative humidity of 90 % and a temperature of 30 C. The treatment time for sterilization is shorter than those of conventional sterilization methods using ethylene oxide gas and dry heat treatment. It is considered that reactive species such as hydroxyl radicals that are effective for the inactivation of Bacillus atrophaeus spores could be produced by the DBD plasma in the humid air. Repetitive micro-pulsed discharge plasmas in the humid air will be applied for the sterilization experiment to enhance the sterilization efficiency.

  17. Energy Transport in Tokamak Plasmas with Central Current Density Control Using Fast Waves

    Energy Technology Data Exchange (ETDEWEB)

    Forest, C.B.; Petty, C.C.; Austin, M.E.; Baity, F.W.; Burrell, K.H.; Chiu, S.C.; Chu, M.S.; deGrassie, J.S.; Gohil, P.; Hyatt, A.W.; Ikezi, H.; Lazarus, E.A.; Murakami, M.; Pinsker, R.I.; Porkolab, M.; Prater, R.; Rice, B.W.; Staebler, G.M.; Strait, E.J.; Taylor, T.S.; Whyte, D.G. [General Atomics, San Diego, California 92186-9784 (United States)]|[University of Maryland, College Park, Maryland 20742-3280 (United States)]|[Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831-8071 (United States)]|[Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)]|[Lawrence Livermore National Laboratory, Livermore, California 94551-9900 (United States)]|[Centre Canadien de Fusion Magnetique, Varennes, Quebec (Canada)

    1996-10-01

    Fast wave current drive has been used to substantially modify the central current density profile in a tokamak plasma. Counter-fast wave current drive (FWCD) applied to discharges with negative central magnetic shear enhances the shear reversal and leads to a distinct transition to a mode of improved core confinement. In this state, the electron thermal diffusivity decreases by (50{plus_minus}20){percent} and the ion diffusivity by (80{plus_minus}20){percent}, compared to just before the transition. The FWCD and electron heating elucidates the role of the current profile on confinement and stability. {copyright} {ital 1996 The American Physical Society.}

  18. New type of discharge-produced plasma source for extreme ultraviolet based on liquid tin jet electrodes

    NARCIS (Netherlands)

    Koshelev, K.N.; Krivtsun, V.M.; Ivanov, V.; Yakushev, O.; Chekmarev, A.; Koloshnikov, V.; Snegirev, E.; Medvedev, Viacheslav

    2012-01-01

    A new approach for discharge-produced plasma (DPP) extreme ultraviolet (EUV) sources based on the usage of two liquid metallic alloy jets as discharge electrodes has been proposed and tested. Discharge was ignited using laser ablation of one of the cathode jets. A system with two jet electrodes was

  19. Multi-Inputs/Multi-Outputs control of plasma current and loop voltage on Tore Supra

    Energy Technology Data Exchange (ETDEWEB)

    Nouailletas, R., E-mail: remy.nouailletas@cea.fr [CEA, F-13108 Saint Paul lez Durance (France); Barana, O.; Saint-Laurent, F.; Brémond, S.; Moreau, P.; Ekedahl, A.; Artaud, J.-F. [CEA, F-13108 Saint Paul lez Durance (France)

    2013-10-15

    During a tokamak discharge, several control modes may have to be run in sequence in order to perform the control of the different discharge phases. The transitions between these control modes are not always easy to handle because in most cases the coupling between the controlled plasma quantities is not taken into account in each control mode design process. This paper presents a new Multi-Inputs/Multi-Outputs (MIMO) controller applied on Tore Supra to control both plasma current and flux variations through the central solenoid voltage and the lower hybrid current drive (LHCD) system power. It deals with the transition from a loop voltage floating mode to a loop voltage control mode. The controller, synthesized and tuned using a model-based approach, has been validated in simulation before its successful implementation on Tore Supra experiments.

  20. Comment on “Two-dimensional positive column structure in a discharge tube with radius discontinuity” [Phys. Plasmas 21, 113503 (2014)

    Energy Technology Data Exchange (ETDEWEB)

    Demidova, M. V. [Department of Chemistry, Wright State University, Dayton, Ohio 45435 (United States); Division of NLP Technology, INTEPH Technology LLC, Dayton, Ohio 45066 (United States); Kudryavtsev, A. A. [Division of NLP Technology, INTEPH Technology LLC, Dayton, Ohio 45066 (United States); International Laboratory “Nonlocal Plasma in Nanotechnology and Medicine”, ITMO University, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); Kurlyandskaya, I. P. [International Laboratory “Nonlocal Plasma in Nanotechnology and Medicine”, ITMO University, Kronverkskiy pr. 49, St. Petersburg 197101 (Russian Federation); Department of Optics, St. Petersburg State University, St. Petersburg 199034 (Russian Federation); Saifutdinov, A. I.; Stepanova, O. M. [Department of Optics, St. Petersburg State University, St. Petersburg 199034 (Russian Federation)

    2015-09-15

    Zobnin et al. have published a paper [Phys. Plasmas, 21, 113503 (2014)] on a topic of discharge physics in the presence of a sharp change in cylindrical discharge geometry. In the comment it is pointed out that for untrapped electrons a full kinetic equation, which includes dependences on spatial coordinates and energies, has to be used for the electron velocity distribution function determination. It is also unclear what probe theories Zobnin et al. have used in their paper for the calculation of electron current to the discharge tube wall.

  1. Treatment of Candida albicans biofilms with low-temperature plasma induced by dielectric barrier discharge and atmospheric pressure plasma jet

    Science.gov (United States)

    Koban, Ina; Matthes, Rutger; Hübner, Nils-Olaf; Welk, Alexander; Meisel, Peter; Holtfreter, Birte; Sietmann, Rabea; Kindel, Eckhard; Weltmann, Klaus-Dieter; Kramer, Axel; Kocher, Thomas

    2010-07-01

    Because of some disadvantages of chemical disinfection in dental practice (especially denture cleaning), we investigated the effects of physical methods on Candida albicans biofilms. For this purpose, the antifungal efficacy of three different low-temperature plasma devices (an atmospheric pressure plasma jet and two different dielectric barrier discharges (DBDs)) on Candida albicans biofilms grown on titanium discs in vitro was investigated. As positive treatment controls, we used 0.1% chlorhexidine digluconate (CHX) and 0.6% sodium hypochlorite (NaOCl). The corresponding gas streams without plasma ignition served as negative treatment controls. The efficacy of the plasma treatment was determined evaluating the number of colony-forming units (CFU) recovered from titanium discs. The plasma treatment reduced the CFU significantly compared to chemical disinfectants. While 10 min CHX or NaOCl exposure led to a CFU log10 reduction factor of 1.5, the log10 reduction factor of DBD plasma was up to 5. In conclusion, the use of low-temperature plasma is a promising physical alternative to chemical antiseptics for dental practice.

  2. Treatment of Candida albicans biofilms with low-temperature plasma induced by dielectric barrier discharge and atmospheric pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Koban, Ina; Welk, Alexander; Meisel, Peter; Holtfreter, Birte; Kocher, Thomas [Unit of Periodontology, Dental School, University of Greifswald, Rotgerberstr. 8, 17475 Greifswald (Germany); Matthes, Rutger; Huebner, Nils-Olaf; Kramer, Axel [Institute for Hygiene and Environmental Medicine, University of Greifswald, Walther-Rathenau-Str. 49 a, 17487 Greifswald (Germany); Sietmann, Rabea [Institute of Microbiology, University of Greifswald, Friedrich-Ludwig-Jahn-Str. 15, 17487 Greifswald (Germany); Kindel, Eckhard; Weltmann, Klaus-Dieter, E-mail: ina.koban@uni-greifswald.d [Leibniz Institute for Plasma Science and Technology (INP), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany)

    2010-07-15

    Because of some disadvantages of chemical disinfection in dental practice (especially denture cleaning), we investigated the effects of physical methods on Candida albicans biofilms. For this purpose, the antifungal efficacy of three different low-temperature plasma devices (an atmospheric pressure plasma jet and two different dielectric barrier discharges (DBDs)) on Candida albicans biofilms grown on titanium discs in vitro was investigated. As positive treatment controls, we used 0.1% chlorhexidine digluconate (CHX) and 0.6% sodium hypochlorite (NaOCl). The corresponding gas streams without plasma ignition served as negative treatment controls. The efficacy of the plasma treatment was determined evaluating the number of colony-forming units (CFU) recovered from titanium discs. The plasma treatment reduced the CFU significantly compared to chemical disinfectants. While 10 min CHX or NaOCl exposure led to a CFU log{sub 10} reduction factor of 1.5, the log{sub 10} reduction factor of DBD plasma was up to 5. In conclusion, the use of low-temperature plasma is a promising physical alternative to chemical antiseptics for dental practice.

  3. Controlled cytotoxicity of plasma treated water formulated by open-air hybrid mode discharge

    Science.gov (United States)

    Lu, P.; Boehm, D.; Cullen, P.; Bourke, P.

    2017-06-01

    Plasma treated liquids (PTLs) provide a means to convey a broad range of effects of relevance for food, environmental, or clinical decontamination, plant growth promotion, and therapeutic applications. Devising the reactive species ingredients and controlling the biological response of PTLs are of great interest. We demonstrate an approach by using an open-air hybrid mode discharge (HMD) to control the principal reactive species composition within plasma treated water (PTW), which is then demonstrated to regulate the cytotoxicity of PTW. The cytotoxicity of HMD produced PTW demonstrates a non-monotonic change over the discharge time. Although hydrogen peroxide and nitrite are not the sole effectors for cell death caused by PTW, using them as principal reactive species indicators, cytotoxicity can be removed and/or enhanced by formulating their concentrations and composition through adjusting the discharge mode and time on-line during PTW generation without the addition of additional working gas or chemical scavengers. This work demonstrates that a hybrid mode discharge can be employed to generate a PTW formulation to control a biological response such as cytotoxicity. This provides insights into how plasma treated liquids may be harnessed for biological applications in a specific and controllable manner.

  4. Relaxation of an electron beam in a crossed-field beam-plasma discharge

    Energy Technology Data Exchange (ETDEWEB)

    Gadeev, K.; Erastov, E.; Ivanov, A.; Muksunov, A.; Nikiforov, V.; Severnyi, V.; Khripunov, B.; Shapkin, V.

    1981-09-01

    The conditions for the formation of a plasma with a high degree of ionization by an electron beam (U/sub b/ = 5 kV, I/sub b/ = 0.07 A) have been studied experimentally in krypton at a density n/sub 0/ = 3 x 10/sup 12/ cm/sup -3/, in crossed electric and magnetic fields. Imposing a resonant electric field can cause both the onset of a volume discharge (under these conditions the dissipation of the beam power increases sharply) and a cutoff of the discharge. An increase in the magnetic field from 8 and 12 kG causes an increase in the power dissipation. The dissipation of the beam power has been studied as a function of the longitudinal dimension of the working volume, in which the beam interacts with the gas. Below a certain minimum length of this region a volume discharge can no longer be formed. The results of this study may prove useful for developing a plasma centrifuge which operates by means of a beam-plasma discharge.

  5. X-ray spectra of plasma radiation from laser induced low-power vacuum discharge

    Science.gov (United States)

    Romanov, I. V.; Kologrivov, A. A.; Paperny, V. L.; Rupasov, A. A.; Starodub, A. N.

    2018-02-01

    The x-ray spectra of plasma radiation in the wavelength range 30–300 Å are studied. The radiation is emitted from plasma of a vacuum discharge with storage energy less than 30 J that is initiated on an Al or Fe cathode by beam from neodymium laser with a power density up to 1012 W cm‑2. It is shown that both the spectral composition and intensity of radiation of hot micropinch plasma that is formed in the cathodic jet are determined by the set of the discharge and the laser pulse characteristics. By optimizing these characteristics, a mode of the discharge operation is attainable, in which a significant portion of the radiation energy is located in the long-wave band of the quasi-continuum (230–270 Å and 160–200 Å for Al and Fe cathodes, respectively). That makes it possible to treat such a discharge as an intense source of narrow-band soft x-ray radiation.

  6. A self-discharge model of Lithium-Sulfur batteries based on direct shuttle current measurement

    DEFF Research Database (Denmark)

    Knap, Vaclav; Stroe, Daniel Loan; Swierczynski, Maciej Jozef

    2016-01-01

    . A simple but comprehensive mathematical model of the Li-S battery cell self-discharge based on the shuttle current was developed and is presented. The shuttle current values for the model parameterization were obtained from the direct shuttle current measurements. Furthermore, the battery cell depth...

  7. Positive direct current corona discharges in single wire-duct electrostatic precipitators

    Energy Technology Data Exchange (ETDEWEB)

    Yehia, Ashraf, E-mail: yehia30161@yahoo.com [Department of Physics, College of Science and Humanitarian Studies at Alkharj, Prince Sattam bin Abdulaziz University, P.O. Box 83, Alkharj 11942 (Saudi Arabia); Department of Physics, Faculty of Science, Assiut University, Assiut 71516, Arab Republic of Egypt (Egypt); Abdel-Fattah, E. [Department of Physics, College of Science and Humanitarian Studies at Alkharj, Prince Sattam bin Abdulaziz University, P.O. Box 83, Alkharj 11942 (Saudi Arabia); Department of Physics, Faculty of Science, Zagazig University, Zagazig 44519, Arab Republic of Egypt (Egypt); Mizuno, Akira [Department of Environmental and Life Sciences, Toyohashi University of Technology, Tempaku-cho, Toyohashi 441-8580 (Japan)

    2016-05-15

    This paper is aimed to study the characteristics of the positive dc corona discharges in single wire-duct electrostatic precipitators. Therefore, the corona discharges were formed inside dry air fed single wire-duct reactor under positive dc voltage at the normal atmospheric conditions. The corona current-voltage characteristics curves have been measured in parallel with the ozone concentration generated inside the reactor under different discharge conditions. The corona current-voltage characteristics curves have agreed with a semi empirical equation derived from the previous studies. The experimental results of the ozone concentration generated inside the reactor were formulated in the form of an empirical equation included the different parameters that were studied experimentally. The obtained equations are valid to expect both the current-voltage characteristics curves and the corresponding ozone concentration that generates with the positive dc corona discharges inside single wire-duct electrostatic precipitators under any operating conditions in the same range of the present study.

  8. Negative edge plasma currents in the SINP tokamak

    Indian Academy of Sciences (India)

    toroidal electric field (ET), Rogowskii coil for the discharge current (Ip) measurements, cos and sin coils for the horizontal ( hor) and vertical ( ver) position measurements respec- tively, a current transformer for the vertical field measurements and toroidal flux loop for the measurements of poloidal beta (βp) and energy ...

  9. Laser beam coupling with capillary discharge plasma for laser wakefield acceleration applications

    Science.gov (United States)

    Bagdasarov, G. A.; Sasorov, P. V.; Gasilov, V. A.; Boldarev, A. S.; Olkhovskaya, O. G.; Benedetti, C.; Bulanov, S. S.; Gonsalves, A.; Mao, H.-S.; Schroeder, C. B.; van Tilborg, J.; Esarey, E.; Leemans, W. P.; Levato, T.; Margarone, D.; Korn, G.

    2017-08-01

    One of the most robust methods, demonstrated to date, of accelerating electron beams by laser-plasma sources is the utilization of plasma channels generated by the capillary discharges. Although the spatial structure of the installation is simple in principle, there may be some important effects caused by the open ends of the capillary, by the supplying channels etc., which require a detailed 3D modeling of the processes. In the present work, such simulations are performed using the code MARPLE. First, the process of capillary filling with cold hydrogen before the discharge is fired, through the side supply channels is simulated. Second, the simulation of the capillary discharge is performed with the goal to obtain a time-dependent spatial distribution of the electron density near the open ends of the capillary as well as inside the capillary. Finally, to evaluate the effectiveness of the beam coupling with the channeling plasma wave guide and of the electron acceleration, modeling of the laser-plasma interaction was performed with the code INF&RNO.

  10. Study of generating nitrogen plasma jet by using glow discharge in non-uniform gap

    Science.gov (United States)

    Liu, Wenzheng; Li, Zhiyi; Ma, Chuanlong; Zhao, Luxiang

    2017-10-01

    Experimental studies of a larger-scale atmospheric pressure glow discharge (APGD) nitrogen plasma jet are presented in this paper. A chamber with non-uniform gap formed in the electrode structure is designed by using non-uniform thickness of dielectrics. Through the electric field simulation, it is found that there is a non-uniform electric field distribution in the lateral and longitudinal directions of the chamber. The discharge starts from the larger electric field intensity of the submillimeter and then is followed by the development to the left and right sides of the smaller electric field intensity of the long gap. Moreover, the non-uniform electric field distribution in the lateral and longitudinal directions can help to suppress the generation of filament discharge. The experiments indicate that a uniform APGD in nitrogen is formed in the chamber and the inner electrode surface has a large luminous intensity. Through the fluid simulation, it is found that the velocity of the gas at the inner electrode surface is large. As a result, the nitrogen flow can effectively bring out the high-density plasmas on the inner electrode surface, which is beneficial to the formation of the plasma jet. The experimental results show that the electrode structure can generate APGD nitrogen plasma jets with the length of 10 mm and width of 15 mm, which is of relatively high application value.

  11. Direct-current cathodic vacuum arc system with magnetic-field mechanism for plasma stabilization.

    Science.gov (United States)

    Zhang, H-S; Komvopoulos, K

    2008-07-01

    Filtered cathodic vacuum arc (FCVA) deposition is characterized by plasma beam directionality, plasma energy adjustment via substrate biasing, macroparticle filtering, and independent substrate temperature control. Between the two modes of FCVA deposition, namely, direct current (dc) and pulsed arc, the dc mode yields higher deposition rates than the pulsed mode. However, maintaining the dc arc discharge is challenging because of its inherent plasma instabilities. A system generating a special configuration of magnetic field that stabilizes the dc arc discharge during film deposition is presented. This magnetic field is also part of the out-of-plane magnetic filter used to focus the plasma beam and prevent macroparticle film contamination. The efficiency of the plasma-stabilizing magnetic-field mechanism is demonstrated by the deposition of amorphous carbon (a-C) films exhibiting significantly high hardness and tetrahedral carbon hybridization (sp3) contents higher than 70%. Such high-quality films cannot be produced by dc arc deposition without the plasma-stabilizing mechanism presented in this study.

  12. Packed-bed reactor/silent-discharge plasma design data report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    In 1992, Congress passed the Federal Facility Compliance Act requiring the U.S. Department of Energy (DOE) to treat and dispose of its mixed waste in accordance with Resource Conservation and Recovery Act (RCRA) land disposal restrictions (LDRs). The DOE Albuquerque Operations Office (AL) currently does not have adequate systems to treat the mixed wastes generated and stored at the nine DOE-AL sites. In response to the need for mixed-waste treatment capacity, DOE-AL organized a Treatment Selection Team under the Mixed-Waste Treatment Program (MWTP) to match mixed wastes with treatment options and develop a strategy for treatment of its mixed waste. The strategy developed by the Treatment Selection Team, as described in the AL Mixed-Waste Treatment Plan (DOE 1994), is to use available off-site commercial treatment facilities for all wastes that can be successfully and cost-effectively treated by such facilities. Where no appropriate commercial treatment facilities exist, mobile treatment units (MTUs) would be developed to treat wastes at the sites where the wastes are generated. Treatment processes used for mixed waste must not only address the hazardous component (i.e., meet LDRs) but also must contain the radioactive component in a form that allows final disposal while protecting workers, the public, and the environment. The packed-bed reactor/silent discharge plasma was chosen as a potential candidate for the treatment of the mixed wastes. The process is described.

  13. Characterization of Ni ferrites powders prepared by plasma arc discharge process

    Science.gov (United States)

    Safari, A.; Gheisari, Kh.; Farbod, M.

    2017-01-01

    The aim of this work was to synthesize a single-phase spinel structure from a mixture of zinc, iron and nickel powders by plasma arc discharge method. A mixture of zinc, iron and nickel powders with the appropriate molar ratio was prepared and formed into a cylindrical shape. The synthesis process was performed in air, oxygen and argon atmospheres with the applied arc current of 400 A and pressure of 1 atm. After establishing an arc between the electrodes, the produced powders were collected and their structure and magnetic properties were examined by XRD and VSM, respectively. ZnO as an impurity was appeared in the as-produced powders owing to the high reactivity of zinc atoms, preventing the formation of Ni-Zn ferrite. A pure spinel structure with the highest saturation magnetization (43.8 emu/g) was observed as zinc powders removed completely from the initial mixture. Morphological evaluations using field emission scanning electron microscopy showed that the mean size of fabricated nanoparticles was in the range 100-200 nm and was dependent on the production conditions.

  14. Ion sources with arc-discharge plasma box driven by directly heated LaB(6) electron emitter or cold cathode.

    Science.gov (United States)

    Ivanov, Alexander A; Davydenko, Vladimir I; Deichuli, Petr P; Shulzhenko, Grigori I; Stupishin, Nikolay V

    2008-02-01

    In the Budker Institute, Novosibirsk, an ion source with arc-discharge plasma box has been developed in the recent years for application in thermonuclear devices for plasma diagnostics. Several modifications of the ion source were provided with extracted current ranging from 1 to 7 A and pulse duration of up to 4 s. Initially, the arc-discharge plasma box with cold cathode was used, with which pulse duration is limited to 2 s by the cathode overheating and sputtering in local arc spots. Recently, a directly heated LaB(6) electron emitter was employed instead, which has extended lifetime compared to the cold cathode. In the paper, characteristics of the beam produced with both arrangements of the plasma box are presented.

  15. Dynamics of the spectral behaviour of an ultrashort laser pulse in an argon-gas-filled capillary discharge-preformed plasma channel

    Directory of Open Access Journals (Sweden)

    Sakai S.

    2013-11-01

    Full Text Available We have reported the argon plasma waveguide produced in an alumina (Al2O3 capillary discharge and used to guide ultrashort laser pulses at intensities of the order of 1016  W/cm2. A one-dimensional magnetohydrodynamic (MHD code was used to evaluate the average degree of ionization of Ar in the preformed plasma channel. The spectrum of the propagated laser pulse in the Ar plasma waveguide was not modified and was well reproduced by a particle-in-cell (PIC simulation under initial ion charge state of Ar3+ in the preformed plasma waveguide. The optimum timing for the laser pulse injection was around 150 ns after initiation of a discharge with a peak current of 200 A.

  16. Characterization of an AC glow-type gliding arc discharge in atmospheric air with a current-voltage lumped model

    Science.gov (United States)

    Kong, Chengdong; Gao, Jinlong; Zhu, Jiajian; Ehn, Andreas; Aldén, Marcus; Li, Zhongshan

    2017-09-01

    Quantitative characterization of a high-power glow-mode gliding arc (GM-GA) discharge operated in open air is performed using a current-voltage lumped model that is built from the perspective of energy balance and electron conservation. The GM-GA discharge is powered by a 35 kHz alternating current power supply. Instantaneous images of the discharge volume are recorded using a high-speed camera at a frame rate of 50 kHz, synchronized with the simultaneously recorded current and voltage waveforms. Detailed analyzation indicates that the electrical input power is dissipated mainly through the transport of vibrationally excited nitrogen and other active radicals (such as O). The plasma is quite non-thermal with the ratio of vibrational and translational temperatures (Tv/Tg) larger than 2 due to the intense energy dissipation. The electron number density reaches 3 × 1019 m-3 and is always above the steady value owing to the short cutting events, which can recover the electron density to a relatively large value and limits the maximum length of the gliding arc. The slow decaying rate of electrons is probably attributed to the decomposed state of a hot gaseous mixture and the related associative ionization.

  17. Optical Diagnostics of Air Flows Induced in Surface Dielectric Barrier Discharge Plasma Actuator

    Science.gov (United States)

    Kobatake, Takuya; Deguchi, Masanori; Suzuki, Junya; Eriguchi, Koji; Ono, Kouichi

    2014-10-01

    A surface dielectric barrier discharge (SDBD) plasma actuator has recently been intensively studied for the flow control over airfoils and turbine blades in the fields of aerospace and aeromechanics. It consists of two electrodes placed on both sides of the dielectric, where one is a top powered electrode exposed to the air, and the other is a bottom grounded electrode encapsulated with an insulator. The unidirectional gas flow along the dielectric surfaces is induced by the electrohydrodynamic (EHD) body force. It is known that the thinner the exposed electrode, the greater the momentum transfer to the air is, indicating that the thickness of the plasma is important. To analyze plasma profiles and air flows induced in the SDBD plasma actuator, we performed time-resolved and -integrated optical emission and schlieren imaging of the side view of the SDBD plasma actuator in atmospheric air. We applied a high voltage bipolar pulse (4-8 kV, 1-10 kHz) between electrodes. Experimental results indicated that the spatial extent of the plasma is much smaller than that of the induced flows. Experimental results further indicated that in the positive-going phase, a thin and long plasma is generated, where the optical emission is weak and uniform; on the other hand, in the negative-going phase, a thick and short plasma is generated, where a strong optical emission is observed near the top electrode.

  18. Obtaining the high-current low-energy electron beams in the systems with a plasma emitter

    CERN Document Server

    Devyatkov, V N; Shchanin, P M

    2001-01-01

    Using gas filled diodes with arc and glow-discharge base plasma emitters one investigated into generation and transfer of high-current electron beams. Using a diode with arc discharge base plasma emitter at 15 kV accelerating voltage one obtained a space charge compensated with up to 1 kA current compressed by proper magnetic field from 8 cm diameter up to 1 cm and transported at over 20 cm distance with 70% efficiency. Using a diode with a glow-discharge one obtained a 80 A current and up to 100 A/cm current density beam. In a weak axial magnetic field with B=0.015 T induction such a beam is transported at 30 cm distance

  19. Measurements of 3D slip velocities and plasma column lengths of a gliding arc discharge

    DEFF Research Database (Denmark)

    Zhu, Jiajian; Gao, Jinlong; Ehn, Andreas

    2015-01-01

    A non-thermal gliding arc discharge was generated at atmospheric pressure in an air flow. The dynamics of the plasma column and tracer particles were recorded using two synchronized high-speed cameras. Whereas the data analysis for such systems has previously been performed in 2D (analyzing...... the single camera image), we provide here a 3D data analysis that includes 3D reconstructions of the plasma column and 3D particle tracking velocimetry based on discrete tomography methods. The 3D analysis, in particular, the determination of the 3D slip velocity between the plasma column and the gas flow......, gives more realistic insight into the convection cooling process. Additionally, with the determination of the 3D slip velocity and the 3D length of the plasma column, we give more accurate estimates for the drag force, the electric field strength, the power per unit length, and the radius...

  20. A numerical simulation study on active species production in dense methane-air plasma discharge

    Science.gov (United States)

    Gui, LI; Muyang, QIAN; Sanqiu, LIU; Huaying, CHEN; Chunsheng, REN; Dezhen, WANG

    2018-01-01

    Recently, low-temperature atmospheric pressure plasmas have been proposed as a potential type of ‘reaction carrier’ for the conversion of methane into value-added chemicals. In this paper, the multi-physics field coupling software of COMSOL is used to simulate the detailed discharge characteristics of atmospheric pressure methane-air plasma. A two-dimensional axisymmetric fluid model is constructed, in which 77 plasma chemical reactions and 32 different species are taken into account. The spatial density distributions of dominant charged ions and reactive radical species, such as {{{CH}}}4+, {{{CH}}}3+, {{{N}}}2+, {{{O}}}2+, H, O, CH3, and CH2, are presented, which is due to plasma chemical reactions of methane/air dissociation (or ionization) and reforming of small fragment radical species. The physicochemical mechanisms of methane dissociation and radical species recombination are also discussed and analyzed.

  1. Cold atmospheric plasma discharged in water and its potential use in cancer therapy

    Science.gov (United States)

    Chen, Zhitong; Cheng, Xiaoqian; Lin, Li; Keidar, Michael

    2017-01-01

    Cold atmospheric plasma (CAP) has emerged as a novel technology for cancer treatment. CAP can directly treat cells and tissue but such direct application is limited to skin or can be invoked as a supplement during open surgery. In this study we report indirect plasma treatment using CAP discharged in deionized (DI) water using three gases as carriers (argon (Ar), helium (He), and nitrogen (N2)). Plasma stimulated water was applied to the human breast cancer cell line (MDA-MB-231). MTT (3-(4, 5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay tests showed that using Ar plasma had the strongest effect on inducing apoptosis in cultured human breast cancer cells. This result is attributed to the elevated production of reactive oxygen species and reactive nitrogen species in water.

  2. Predictive Study of Non-Inductive Current Drive Discharge Modes using Newly Upgraded ASTRA code in KSTAR

    Science.gov (United States)

    Ju, Myunghee

    1999-11-01

    To investigate the reference discharge scenarios for the steady state operation in KSTAR [1], the code ASTRA (An Automatic System for TRansport Analysis) [2] has been upgraded: (A) the ray-tracing lower-hybrid wave code LSC [3] is newly added in ASTRA , (B) the neutral beam solver is modified with the KSTAR parameters [4], (C) the ICRF (Ion Cyclotron Ranges of Frequency) full wave code TORIC [5] is also newly implemented in ASTRA. With the newly upgraded ASTRA code, the predictive study of 100current drive discharge scenarios in neutral beam + lower hybrid wave + fast wave heated plasma has been done with a variety of transport models in the KSTAR tokamak reference plasma. * Work supported by the Ministry of Science and Technology, Korea. [1] G. S. Lee, Y. Kim, S. M. Hwang, J. Kim, and D. I. Choi, Bull. Am. Phys. Soc. 41, 7 (1996). [2] Pereverzev G.V. et al., Preprint IPP 5/42, Garching, 1991. [3] D.W. Ignat et al, Nuclear Fusion. Vol. 34, No. 6, 1994. [4] Alexi Polevoi et al., JAERI-DATA/Code 97-014. [5] M. Brambilla, A Full Wave Code for Ion Cyclotron Waves in Toroidal Plasmas, Report IPP 5/66, Garching, 1996.

  3. Boltzmann statistical consideration on the excitation mechanism of iron atomic lines emitted from glow discharge plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Lei; Kashiwakura, Shunsuke; Wagatsuma, Kazuaki, E-mail: wagatuma@imr.tohoku.ac.jp

    2011-11-15

    A Boltzmann plot for many iron atomic lines having excitation energies of 3.3-6.9 eV was investigated in glow discharge plasmas when argon or neon was employed as the plasma gas. The plot did not show a linear relationship over a wide range of the excitation energy, but showed that the emission lines having higher excitation energies largely deviated from a normal Boltzmann distribution whereas those having low excitation energies (3.3-4.3 eV) well followed it. This result would be derived from an overpopulation among the corresponding energy levels. A probable reason for this is that excitations for the high-lying excited levels would be caused predominantly through a Penning-type collision with the metastable atom of argon or neon, followed by recombination with an electron and then stepwise de-excitations which can populate the excited energy levels just below the ionization limit of iron atom. The non-thermal excitation occurred more actively in the argon plasma rather than the neon plasma, because of a difference in the number density between the argon and the neon metastables. The Boltzmann plots yields important information on the reason why lots of Fe I lines assigned to high-lying excited levels can be emitted from glow discharge plasmas. - Highlights: Black-Right-Pointing-Pointer This paper shows the excitation mechanism of Fe I lines from a glow discharge plasma. Black-Right-Pointing-Pointer A Boltzmann distribution is studied among iron lines of various excitation levels. Black-Right-Pointing-Pointer We find an overpopulation of the high-lying energy levels from the normal distribution. Black-Right-Pointing-Pointer It is caused through Penning-type collision of iron atom with argon metastable atom.

  4. Runaway electron studies with hard x-ray and microwave diagnostics in the FT-2 lower hybrid current drive discharges

    Science.gov (United States)

    Shevelev, A. E.; Khilkevitch, E. M.; Lashkul, S. I.; Rozhdestvensky, V. V.; Pandya, S. P.; Plyusnin, V. V.; Altukhov, A. B.; Kouprienko, D. V.; Chugunov, I. N.; Doinikov, D. N.; Esipov, L. A.; Gin, D. B.; Iliasova, M. V.; Naidenov, V. O.; Polunovsky, I. A.; Sidorov, A. V.; Kiptily, V. G.

    2018-01-01

    Studies of the super-thermal and runaway electron behavior in ohmic and lower hybrid current drive FT-2 tokamak plasmas have been carried out using information obtained from measurements of hard x-ray spectra and non-thermal microwave radiation intensity at the frequency of 10 GHz and in the range of (53 ÷ 78) GHz. A gamma-ray spectrometer based on a scintillation detector with a LaBr3(Ce) crystal was used, which provides measurements at counting rates up to 107 s‑1. Reconstruction of the energy distribution of RE interacting with the poloidal limiter of the tokamak chamber was made with application of the DeGaSum code. Super-thermal electrons accelerated up to 2 MeV by the LH waves at the high-frequency pumping of the plasma with low density ≤ft ~ 2  ×  1013 cm‑3 and then up to 7 MeV by vortex electric field have been found. Experimental analysis of the runaway electron beam generation and evolution of their energy distribution in the FT-2 plasmas is presented in the article and compared with the numerical calculation of the maximum energy gained by runaway electrons for given plasma parameters. In addition, possible mechanisms for limiting the maximum energy gained by the runaway electrons are also calculated and described for a FT-2 plasma discharge.

  5. Analysis of Ar plasma jets induced by single and double dielectric barrier discharges at atmospheric pressure

    Science.gov (United States)

    Judée, F.; Merbahi, N.; Wattieaux, G.; Yousfi, M.

    2016-09-01

    The aim is the comparison of different plasma parameters of single and double dielectric barrier discharge plasma jet configurations (S-DBD and D-DBD) which are potentially usable in biomedical applications. Both configurations are studied in terms of electric field distribution, electrical discharge characteristics, plasma parameters (estimated by optical emission spectroscopy analysis), and hydrodynamics of the plasma jet for electrical parameters of power supplies corresponding to an applied voltage of 10 kV, pulse duration of 1 μs, frequency of 9.69 kHz, and Ar flow of 2 l/min. We observed that the D-DBD configuration requires half the electrical power one needs to provide in the S-DBD case to generate a plasma jet with similar characteristics: excitation temperature around 4700 K, electron density around 2.5 × 1014 cm-3, gas temperature of about 320 K, a relatively high atomic oxygen concentration reaching up to 1000 ppm, the presence of reactive oxygen and nitrogen species (nitric oxide, hydroxyl radical, and atomic oxygen), and an irradiance in the UV-C range of about 20 μW cm-2. Moreover, it has been observed that D-DBD plasma jet is more sensitive to short pulse durations, probably due to the charge accumulation over the dielectric barrier around the internal electrode. This results in a significantly longer plasma length in the D-DBD configuration than in the S-DBD one up to a critical flow rate (2.25 l/min) before the occurrence of turbulence in the D-DBD case. Conversely, ionization wave velocities are significantly higher in the S-DBD setup (3.35 × 105 m/s against 1.02 × 105 m/s for D-DBD), probably due to the higher electrostatic field close to the high voltage electrode in the S-DBD plasma jet.

  6. Studies of thermal energy confinement scaling in PDX plasmas: D/sup 0/. -->. H/sup +/ limiter discharges

    Energy Technology Data Exchange (ETDEWEB)

    Kaye, S.M.; Goldston, R.J.; Bell, M.; Bol, K.; Bitter, M.; Fonck, R.; Grek, B.; Hawryluk, R.J.; Johnson, D.; Kaita, R.

    1984-06-01

    Experiments were performed on the PDX tokamak to study plasma heating and ..beta.. scaling with higher power, near-perpendicular neutral beam injection. The data taken during these experiments were analyzed using a time-dependent data interpretation code (TRANSP) to study the transport and thermal confinement scaling over a wide range of plasma parameters. This study focuses on results from experiments with D/sup 0/ injection into H/sup +/ plasmas using graphite rail limiters, a = 40 to 44 cm, R = 143 cm, I/sub p/ = 200 to 480 kA, B/sub T/ = 0.7 to 2.2 T, and typically anti n/sub e/ = 2.5 to 4.2 x 10/sup 13/ cm/sup -3/. The results of this study indicate that for both ohmic and neutral beam heated discharges the energy flow out of the plasma is dominated by anomalous electron losses, attributed to electron thermal conduction. The ion conduction losses are well described to electron thermal conduction. The ion conduction losses are well described by neoclassical theory; however, the total ion loss influences the power balance significantly only at high toroidal fields and high plasma currents.

  7. Accurate characterization of RF antennas for low-temperature plasma discharges with non-uniform magneto-static fields

    Science.gov (United States)

    Melazzi, Davide; Lancellotti, Vito; Cardinali, Alessandro; Manente, Marco; Pavarin, Daniele

    2014-10-01

    The analysis of Radio Frequency Helicon plasma sources appears to have focused on the absorption of electromagnetic energy, but not much on the role played by the antenna driving the plasma discharge. In fact, most approaches assume (i) the induced current density on the antenna a priori, and (ii) a uniform magneto-static field aligned with the plasma column. To determine the antenna current self-consistently and to consider non-uniform magneto-static fields we have developed two codes: ADAMANT and RAYWh. The former implements a full-wave approach to evaluate the current distribution on the antenna and the antenna impedance, which is crucial for the design of the feeding network. RAYWh solves the 3D Maxwell-Vlasov model equations by a WKB asymptotic expansion, and is capable of predicting the occurrence of mode transitions. We report on a comparative study of various antennas working in the 1--30 MHz range commonly used in Helicon sources. The current distribution on the antenna, power deposition, and wave propagation phenomena have been investigated for various density profiles, magneto-static field configurations, neutral pressure, electron temperature.

  8. Plasma decay in high-voltage nanosecond discharges in oxygen-containing mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Anokhin, E. M.; Popov, M. A. [Moscow Institute of Physics and Technology (Russian Federation); Kochetov, I. V. [Troitsk Institute for Innovation and Fusion Research (Russian Federation); Aleksandrov, N. L., E-mail: nick-aleksandrov@mail.ru [Moscow Institute of Physics and Technology (Russian Federation); Starikovskii, A. Yu. [Princeton University (United States)

    2016-01-15

    Plasma decay in high-voltage nanosecond discharges in CO{sub 2}: O{sub 2} and Ar: O{sub 2} mixtures at room gas temperature and a pressure of 10 Torr is studied experimentally and theoretically. The time dependence of the electron density during plasma decay is measured using microwave interferometry. The time evolution of the charged particle density, ion composition, and electron temperature is simulated numerically. It is shown that, under the given conditions, the discharge plasma is dominated for the most time by O{sub 2}{sup +} ions and plasma decay is determined by dissociative and three-body electron−ion recombination. As in the previous studies performed for air and oxygen plasmas, agreement between measurements and calculations is achieved only under the assumption that the rate of three-body recombination of molecular ions is much greater than that for atomic ions. The values of the rate constant of three-body recombination of electrons with O{sub 2}{sup +} ions in a wide range of electron temperatures (500–5500 K), as well as for thermal (300 K) electrons, are obtained by processing the experimental results.

  9. Hierarchical modeling of plasma and transport phenomena in a dielectric barrier discharge reactor

    Science.gov (United States)

    Bali, N.; Aggelopoulos, C. A.; Skouras, E. D.; Tsakiroglou, C. D.; Burganos, V. N.

    2017-12-01

    A novel dual-time hierarchical approach is developed to link the plasma process to macroscopic transport phenomena in the interior of a dielectric barrier discharge (DBD) reactor that has been used for soil remediation (Aggelopoulos et al 2016 Chem. Eng. J. 301 353–61). The generation of active species by plasma reactions is simulated at the microseconds (µs) timescale, whereas convection and thermal conduction are simulated at the macroscopic (minutes) timescale. This hierarchical model is implemented in order to investigate the influence of the plasma DBD process on the transport and reaction mechanisms during remediation of polluted soil. In the microscopic model, the variables of interest include the plasma-induced reactive concentrations, while in the macroscopic approach, the temperature distribution, and the velocity field both inside the discharge gap and within the polluted soil material as well. For the latter model, the Navier–Stokes and Darcy Brinkman equations for the transport phenomena in the porous domain are solved numerically using a FEM software. The effective medium theory is employed to provide estimates of the effective time-evolving and three-phase transport properties in the soil sample. Model predictions considering the temporal evolution of the plasma remediation process are presented and compared with corresponding experimental data.

  10. Skeletal cell differentiation is enhanced by atmospheric dielectric barrier discharge plasma treatment.

    Directory of Open Access Journals (Sweden)

    Marla J Steinbeck

    Full Text Available Enhancing chondrogenic and osteogenic differentiation is of paramount importance in providing effective regenerative therapies and improving the rate of fracture healing. This study investigated the potential of non-thermal atmospheric dielectric barrier discharge plasma (NT-plasma to enhance chondrocyte and osteoblast proliferation and differentiation. Although the exact mechanism by which NT-plasma interacts with cells is undefined, it is known that during treatment the atmosphere is ionized generating extracellular reactive oxygen and nitrogen species (ROS and RNS and an electric field. Appropriate NT-plasma conditions were determined using lactate-dehydrogenase release, flow cytometric live/dead assay, flow cytometric cell cycle analysis, and Western blots to evaluate DNA damage and mitochondrial integrity. We observed that specific NT-plasma conditions were required to prevent cell death, and that loss of pre-osteoblastic cell viability was dependent on intracellular ROS and RNS production. To further investigate the involvement of intracellular ROS, fluorescent intracellular dyes Mitosox (superoxide and dihydrorhodamine (peroxide were used to assess onset and duration after NT-plasma treatment. Both intracellular superoxide and peroxide were found to increase immediately post NT-plasma treatment. These increases were sustained for one hour but returned to control levels by 24 hr. Using the same treatment conditions, osteogenic differentiation by NT-plasma was assessed and compared to peroxide or osteogenic media containing β-glycerolphosphate. Although both NT-plasma and peroxide induced differentiation-specific gene expression, neither was as effective as the osteogenic media. However, treatment of cells with NT-plasma after 24 hr in osteogenic or chondrogenic media significantly enhanced differentiation as compared to differentiation media alone. The results of this study show that NT-plasma can selectively initiate and amplify ROS

  11. Numerical study of capacitive coupled HBr/Cl2 plasma discharge for dry etch applications

    Science.gov (United States)

    Gul, Banat; Ahmad, Iftikhar; Zia, Gulfam; Aman-ur-Rehman

    2016-09-01

    HBr/Cl2 plasma discharge is investigated to study the etchant chemistry of this discharge by using the self-consistent fluid model. A comprehensive set of gas phase reactions (83 reactions) including primary processes such as excitation, dissociation, and ionization are considered in the model along with 24 species. Our findings illustrate that the densities of neutral species (i.e., Br, HCl, Cl, H, and H2) produced in the reactor are higher than charged species (i.e., Cl2+, Cl-, HBr+, and Cl+). Density profile of neutral and charged species followed bell shaped and double humped distributions, respectively. Increasing Cl2 fraction in the feedback gases (HBr/Cl2 from 90/10 to 10/90) promoted the production of Cl, Cl+, and Cl2+ in the plasma, indicating that chemical etching pathway may be preferred at high Cl-environment. These findings pave the way towards controlling/optimizing the Si-etching process.

  12. Plasma Discharges in Gas Bubbles in Liquid Water: Breakdown Mechanisms and Resultant Chemistry

    Science.gov (United States)

    Gucker, Sarah M. N.

    The use of atmospheric pressure plasmas in gases and liquids for purification of liquids has been investigated by numerous researchers, and is highly attractive due to their strong potential as a disinfectant and sterilizer. However, the fundamental understanding of plasma production in liquid water is still limited. Despite the decades of study dedicated to electrical discharges in liquids, many physical aspects of liquids, such as the high inhomogeneity of liquids, complicate analyses. For example, the complex nonlinearities of the fluid have intricate effects on the electric field of the propagating streamer. Additionally, the liquid material itself can vaporize, leading to discontinuous liquid-vapor boundaries. Both can and do often lead to notable hydrodynamic effects. The chemistry of these high voltage discharges on liquid media can have circular effects, with the produced species having influence on future discharges. Two notable examples include an increase in liquid conductivity via charged species production, which affects the discharge. A second, more complicated scenario seen in some liquids (such as water) is the doubling or tripling of molecular density for a few molecule layers around a high voltage electrode. These complexities require technological advancements in optical diagnostics that have only recently come into being. This dissertation investigates several aspects of electrical discharges in gas bubbles in liquids. Two primary experimental configurations are investigated: the first allows for single bubble analysis through the use of an acoustic trap. Electrodes may be brought in around the bubble to allow for plasma formation without physically touching the bubble. The second experiment investigates the resulting liquid phase chemistry that is driven by the discharge. This is done through a dielectric barrier discharge with a central high voltage surrounded by a quartz discharge tube with a coil ground electrode on the outside. The plasma

  13. GeV Electron Beams from a Capillary Discharge Guided Laser Plasma Accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Kei; Gonsalves, Anthony; Panasenko, Dmitriy; Lin, Chen; Toth, Csaba; Geddes, Cameron; Schroeder, Carl; Esarey, Eric; Leemans, Wim

    2010-07-08

    Laser plasma acceleration (LPA) up to 1 GeV has been realized at Lawrence Berkeley National Laboratory by using a capillary discharge waveguide. In this paper, the capillary discharge guided LPA system including a broadband single-shot electron spectrometer is described. The spectrometer was designed specifically for LPA experiments and has amomentumacceptance of 0.01 - 1.1 GeV/c with a percent level resolution. Experiments using a 33 mm long, 300 mu m diameter capillary demonstrated the generation of high energy electron beams up to 1 GeV. By de-tuning discharge delay from optimum guiding performance, selftrapping and acceleration were found to be stabilized producing 460 MeV electron beams.

  14. The role of gas composition in plasma-dust structures in RF discharge

    Energy Technology Data Exchange (ETDEWEB)

    Maiorov, S. A., E-mail: maiorov-sa@mail.ru [Prokhorov General Physics Institute, Russian Academy of Sciences, Vavilov st. 38, Moscow 119991 (Russian Federation); Joint Institute for High Temperatures, Russian Academy of Sciences, Izhorskaya st. 13/19, Moscow 127412 (Russian Federation); Kodanova, S. K.; Dosbolayev, M. K.; Ramazanov, T. S.; Bastykova, N. Kh.; Utegenov, A. U. [Institute of Experimental and Theoretical Physics, Al-Farabi Kazakh National University, Al-Farabi 71, Almaty 050040 (Kazakhstan); Golyatina, R. I. [Prokhorov General Physics Institute, Russian Academy of Sciences, Vavilov st. 38, Moscow 119991 (Russian Federation)

    2015-03-15

    The influence of a mixture of light and heavy gases, i.e., helium and argon, on plasma-dust structures in the radiofrequency discharge has been studied. The dust chains in the sheath of the radiofrequency discharge, the average distance between the dust particles and their chains, have been analyzed. A significant effect of small amounts of argon on the correlation characteristics of dust particles has been observed. The results of numerical simulation of ion and electron drift in the mixture of helium and argon are presented. It is shown that even 1% of argon admixture to helium produces such an effect that argon ions become the main components of the discharge, as they drift with lightweight helium forming a strongly anisotropic velocity distribution function.

  15. Methane Incorporation into Liquid Fuel by Non-Equilibrium Plasma Discharges

    CERN Document Server

    Liu, Chong; Ji, Hai-Feng; Smith, Joshua; Rabinovich, Alexander; Dobrynin, Danil; Fridman, Alexander

    2016-01-01

    The conventional ways of processing natural gas into more efficient and economical fuels usually either have low conversion rate or low energy efficiency. In this work, a new approach of methane liquefaction is proposed. Instead of direct treatment of only natural gas, plasma activated methane is reacting with liquid fuel. In this way, methane molecules are directly incorporated onto liquid fuel to achieve liquefaction. Nanosecond-pulsed dielectric barrier discharge and atmospheric pressure glow discharge are used here to ensure no local heating in gas bubbles. Effects of both discharges on methane reaction with liquid fuel are investigated, mass and chemical changes in liquid are observed. Preliminary results show fixation of methane in liquid fuel.

  16. ANALYSIS OF A COMMERCIAL PORTABLE LITHIUM-ION BATTERY UNDER LOW CURRENT CHARGE-DISCHARGE CYCLES

    Directory of Open Access Journals (Sweden)

    Stephany Pires da Silva

    Full Text Available The dependence between the transferred charge and the corresponding transference time to charge and discharge a portable cell phone Li-ion battery (LiCoO2/C under cycles of low intensity currents was studied in detail. The voltage curve profile between 3.0 and 4.2 V and the charging and discharging time are strongly influenced by the applied current intensity. A linear dependence between the stored and extracted charges, into and from the battery, with the intensity of applied current was also observed. Allometric equations were found to describe the correlation between the charge transference time and the applied current intensity to charge and discharge the battery.

  17. Alternating current plasma operation in the STOR-M tokamak

    Science.gov (United States)

    Mitarai, O.; Xiao, Chijin; Zhang, Liyan; McColl, D.; Zhang, Wei; Conway, G.; Hirose, A.; Skarsgard, H. M.

    1996-10-01

    One cycle alternating current (AC) plasma operation without a dwell time has been achieved in the STOR-M tokamak with good reproducibility using a newly developed ohmic heating circuit. The plasma current of +24 kA is smoothly ramped down in 10 ms with a rampdown rate of around 2.0 kA/ms and then ramped up to between -20 and -24 kA directly without a dwell time. The plasma density of up to (3.7+or-0.6)*1018 m-3 remains at the current reversal as observed in recent soft landing experiments. The key to a successful, reproducible and direct transition in AC tokamak operations on STOR-M is to control both the total vertical field by a feedback control system and the plasma density by careful gas puffing during the current reversal phase. This experiment has demonstrated that the initial loop voltage for the second negative current is minimized when the dwell time approaches zero, and the AC operation without dwelling is possible whenever the plasma current can be softly terminated with a finite residual plasma density

  18. Determination of plasma density from data on the ion current to cylindrical and planar probes

    Energy Technology Data Exchange (ETDEWEB)

    Voloshin, D. G., E-mail: dvoloshin@mics.msu.su; Vasil’eva, A. N.; Kovalev, A. S.; Mankelevich, Yu. A.; Rakhimova, T. V. [Moscow State University, Skobeltsyn Nuclear Physics Institute (Russian Federation)

    2016-12-15

    To improve probe methods of plasma diagnostics, special probe measurements were performed and numerical models describing ion transport to a probe with allowance for collisions were developed. The current–voltage characteristics of cylindrical and planar probes were measured in an RF capacitive discharge in argon at a frequency of 81 MHz and plasma densities of 10{sup 10}–10{sup 11} cm{sup –3}, typical of modern RF reactors. 1D and 2D numerical models based on the particle-in-cell method with Monte Carlo collisions for simulating ion motion and the Boltzmann equilibrium for electrons are developed to describe current collection by a probe. The models were used to find the plasma density from the ion part of the current–voltage characteristic, study the effect of ion collisions, and verify simplified approaches to determining the plasma density. A 1D hydrodynamic model of the ion current to a cylindrical probe with allowance for ion collisions is proposed. For a planar probe, a method to determine the plasma density from the averaged numerical results is developed. A comparative analysis of different approaches to calculating the plasma density from the ion current to a probe is performed.

  19. Gene Transfection Method Using Atmospheric Pressure Dielectric-Barrier Discharge Plasmas

    Science.gov (United States)

    Sasaki, Shota; Kanzaki, Makoto; Kaneko, Toshiro

    2013-09-01

    Gene transfection which is the process of deliberately introducing nucleic acids into cells is expected to play an important role in medical treatment because the process is necessary for gene therapy and creation of induced pluripotent stem (iPS) cells. However, the conventional transfection methods have some problems, so we focus attention on promising transfection methods by atmospheric pressure dielectric-barrier discharge (AP-DBD) plasmas. AP-DBD He plasmas are irradiated to the living cell covered with genes. Preliminarily, we use fluorescent dye YOYO-1 instead of the genes and use LIVE/DEAD Stain for cell viability test, and we analyze the transfection efficiency and cell viability under the various conditions. It is clarified that the transfection efficiency is strongly dependence on the plasma irradiation time and cell viability rates is high rates (>90%) regardless of long plasma irradiation time. These results suggest that ROS (Reactive Oxygen Species) and electric field generated by the plasma affect the gene transfection. In addition to this (the plasma irradiation time) dependency, we now investigate the effect of the plasma irradiation under the various conditions.

  20. Degradation of triclosan in aqueous solution by dielectric barrier discharge plasma combined with activated carbon fibers.

    Science.gov (United States)

    Xin, Lu; Sun, Yabing; Feng, Jingwei; Wang, Jian; He, Dong

    2016-02-01

    The degradation of triclosan (TCS) in aqueous solution by dielectric barrier discharge (DBD) plasma with activated carbon fibers (ACFs) was investigated. In this study, ACFs and DBD plasma coexisted in a planar DBD plasma reactor, which could synchronously achieve degradation of TCS, modification and in situ regeneration of ACFs, enhancing the effect of recycling of ACFs. The properties of ACFs before and after modification by DBD plasma were characterized by BET and XPS. Various processing parameters affecting the synergetic degradation of TCS were also investigated. The results exhibited excellent synergetic effects in DBD plasma-ACFs system on TCS degradation. The degradation efficiency of 120 mL TCS with initial concentration of 10 mg L(-1) could reach 93% with 1 mm thick ACFs in 18 min at input power of 80 W, compared with 85% by single DBD plasma. Meanwhile, the removal rate of total organic carbon increased from 12% at pH 6.26-24% at pH 3.50. ACFs could ameliorate the degradation efficiency for planar DBD plasma when treating TCS solution at high flow rates or at low initial concentrations. A possible degradation pathway of TCS was investigated according to the detected intermediates, which were identified by liquid chromatography-hybrid quadrupole time-of-flight mass spectrometry (LC-QTOF-MS) combined with theoretical calculation of Gaussian 09 program. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Optical emission diagnostics for plasma parameters in pulse-modulated argon capacitively-coupled discharges

    Science.gov (United States)

    Wang, Shicong; Boffard, John B.; Lin, Chun C.; Wendt, Amy E.

    2014-10-01

    Pulsing of discharge power in low pressure rf plasmas is a means to improve materials processing outcomes. Plasma-surface interactions depend on the relative fluxes of ions, reactive neutrals and photons, which can be controlled by adjusting pulse frequency and duty cycle, due their effect on plasma properties, particularly the electron energy distribution. We report on an optical emission spectroscopy (OES) based plasma diagnostic to characterize the time evolution of plasma properties within the pulse cycle for two systems: a pulsed capacitively-coupled plasma (CCP), and a pulsed CCP in combination with a continuous-wave (cw) inductively coupled plasma (ICP); Typical conditions: 30 mTorr Ar, 13.56 MHz rf power (400 W peak CCP and 500 W ICP) and 1 kHz pulse frequency. We quantify the trade off between time resolution versus uncertainty in measured OES intensities. Because only a small fraction of CCP rf power contributes to electron heating, the method is limited by relatively low absolute OES intensities for the CCP-only case, and small incremental changes in intensity when the pulsed CCP is combined with the cw ICP. Nevertheless, with sufficient signal averaging, even subtle changes in parameters induced by the CCP in the latter case can be quantified. This work was supported in part by NSF Grant PHY-1068670.

  2. Propagation characteristics of dust–acoustic waves in presence of a floating cylindrical object in the DC discharge plasma

    Energy Technology Data Exchange (ETDEWEB)

    Choudhary, Mangilal, E-mail: mangilal@ipr.res.in [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India); Homi Bhabha National Institute, Training School Complex, Anushakti Nagar, Mumbai 400085 (India); Mukherjee, S.; Bandyopadhyay, P. [Institute for Plasma Research, Bhat, Gandhinagar 382428 (India)

    2016-08-15

    The experimental observation of the self–excited dust acoustic waves (DAWs) and its propagation characteristics in the absence and presence of a floating cylindrical object is investigated. The experiments are carried out in a direct current (DC) glow discharge dusty plasma in a background of argon gas. Dust particles are found levitated at the interface of plasma and cathode sheath region. The DAWs are spontaneously excited in the dust medium and found to propagate in the direction of ion drift (along the gravity) above a threshold discharge current at low pressure. Excitation of such a low frequency wave is a result of the ion–dust streaming instability in the dust cloud. Characteristics of the propagating dust acoustic wave get modified in the presence of a floating cylindrical object of radius larger than that of the dust Debye length. Instead of propagation in the vertical direction, the DAWs are found to propagate obliquely in the presence of the floating object (kept either vertically or horizontally). In addition, a horizontally aligned floating object forms a wave structure in the cone shaped dust cloud in the sheath region. Such changes in the propagation characteristics of DAWs are explained on the basis of modified potential (or electric field) distribution, which is a consequence of coupling of sheaths formed around the cylindrical object and the cathode.

  3. Propagation characteristics of dust$-$acoustic waves in presence of a floating cylindrical object in the DC discharge plasma

    CERN Document Server

    Choudhary, Mangilal; Bandyopadhyay, P

    2016-01-01

    The experimental observation of the self$-$excited dust acoustic waves (DAWs) and its propagation characteristics in the absence and presence of a floating cylindrical object are investigated. The experiments are carried out in a direct current (DC) glow discharge dusty plasma in the background of argon gas. Dust particles are found levitated at the interface of plasma and cathode sheath region. The DAWs are spontaneously excited in the dust medium and found to propagate in the direction of ion drift (along the gravity) above a threshold discharge current at lower pressure. The excitation of such low frequency wave is a result of the ion--dust streaming instability in the dust cloud. The characteristics of the propagating dust acoustic wave get modified in presence of a floating cylindrical object of radius larger than the dust Debye length. Instead of propagating in the vertical direction, the DAWs are found to propagate obliquely in presence of the floating object (kept either vertically or horizontally). I...

  4. Surface modification of chitosan/PEO nanofibers by air dielectric barrier discharge plasma for acetylcholinesterase immobilization

    Energy Technology Data Exchange (ETDEWEB)

    Dorraki, Naghme, E-mail: n.dorraki@web.sbu.ac.ir [Laser and Plasma Research Institute, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Safa, Nasrin Navab [Laser and Plasma Research Institute, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Jahanfar, Mehdi [Protein Research Center, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Ghomi, Hamid [Laser and Plasma Research Institute, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of); Ranaei-Siadat, Seyed-Omid [Protein Research Center, Shahid Beheshti University, Evin 1983963113, Tehran (Iran, Islamic Republic of)

    2015-09-15

    Highlights: • We used an economical and effective method for surface modification. • Chitosan/PEO nanofibrous membranes were modified by air-DBD plasma. • The most NH{sub 3}{sup +} group was generated on the 6 min plasma modified membrane. • We immobilized acetylcholinesterase on the plasma modified and unmodified membranes. • More enzyme activity was detected on the modified membrane by plasma. - Abstract: There are different methods to modify polymer surfaces for biological applications. In this work we have introduced air-dielectric barrier discharge (DBD) plasma at atmospheric pressure as an economical and safe method for modifying the surface of electrospun chitosan/PEO (90/10) nanofibers for acetylcholinesterase (AChE) immobilization. According to the contact angle measurement results, the nanofibers become highly hydrophilic when they are exposed to the DBD plasma for 6 min in compared to unmodified membrane. Attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) results reveal hydroxyl, C=O and NH{sub 3}{sup +} polar groups increment after 6 min plasma treatment. Contact angle measurements and ATR-FTIR results are confirmed by X-ray photoelectron spectroscopy (XPS). AChE at pH 7.4 carries a negative charge and after immobilization on the surface of plasma-treated nanofibrous membrane attracts the NH{sub 3}{sup +} group and more enzyme activity is detected on the plasma-modified nanofibers for 6 min in compared to unmodified nanofibers. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) are used for the surface topography and morphology characterization. The results have proved that air-DBD plasma is a suitable method for chitosan/PEO nanofibrous membrane modification as a biodegradable and functionalized substrate for enzyme immobilization.

  5. Observation of plasma jets in a table top plasma focus discharge

    Energy Technology Data Exchange (ETDEWEB)

    Pavez, Cristian; Soto, Leopoldo, E-mail: lsoto@cchen.cl [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Center for Research and Applications in Plasma Physics and Pulsed Power, P4, Santiago-Talca (Chile); Departamento de Ciencias Físicas, Facultad de Ciencias Exactas, Universidad Andrés Bello, República 220, Santiago (Chile); Pedreros, José [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Departamento de Ingeniería Eléctrica, Universidad de Santiago de Chile, Santiago (Chile); Tarifeño-Saldivia, Ariel [Comisión Chilena de Energía Nuclear, CCHEN, Casilla 188-D, Santiago (Chile); Center for Research and Applications in Plasma Physics and Pulsed Power, P4, Santiago-Talca (Chile)

    2015-04-15

    In the last years, medium size Z-pinch experiments operating at tens of kJ are being used to create supersonic plasma jets. Those experiments are produced with wire arrays and radial foils, and they are conducted in generators based on water-filled transmission lines. Also plasma jets have been observed in small X-pinch experiments operating at 1 kJ. In this work, observations of plasma jets produced in a table top plasma focus device by means of optical and digital interferometry are shown. The device was operated at only ∼70 J, achieving 50 kA in 150 ns. The plasma jets were observed after the pinch, in the region close and on the anode, along the axis. The electron density measured from the jets is in the range 10{sup 24}–10{sup 25 }m{sup −3}. From two consecutive plasma images separated 18 ns, the axial jet velocity was measured in the order of 4 × 10{sup 4 }m/s.

  6. Experimental investigation on electrical characteristics and dose measurement of dielectric barrier discharge plasma device used for therapeutic application

    Science.gov (United States)

    Shahbazi Rad, Zahra; Abbasi Davani, Fereydoun

    2017-04-01

    In this research, a Dielectric Barrier Discharge (DBD) plasma device operating in air has been made. The electrical characteristics of this device like instantaneous power, dissipated power, and discharge capacitance have been measured. Also, the effects of applied voltage on the dissipated power and discharge capacitance of the device have been investigated. The determination of electrical parameters is important in DBD plasma device used in living tissue treatment for choosing the proper treatment doses and preventing the destructive effects. The non-thermal atmospheric pressure DBD plasma source was applied for studying the acceleration of blood coagulation time, in vitro and wound healing time, in vivo. The citrated blood drops coagulated within 5 s treatment time by DBD plasma. The effects of plasma temperature and electric field on blood coagulation have been studied as an affirmation of the applicability of the constructed device. Also, the effect of constructed DBD plasma on wound healing acceleration has been investigated.

  7. INPROVING OF THE QUALITY FOOD FOR ANIMALS BY PULSED POWER PLASMA DISCHARGE

    Directory of Open Access Journals (Sweden)

    Sebastian Gnapowski

    2015-08-01

    Full Text Available Soy beans powder mixed with water is a good food for animals. However, there are two problems with this brew. One is that soy beans powder is sunk down to fast. Parts of soy beans powder are too big and too heavy. Animals do not eat soy beans powder because after a few minutes (around 3min is sunk down and soy beans are on the bottom case. Another negative point is a quick growth of mold, especially during summer when the temperature is highest. Mold is making food unhealthy and causes unpleasant smell. After mold appears it is difficult to clean the case. One of the solutions to eliminate these problems is to use pulse power plasma discharge and the second solution is ultra sound treatment. It was observed that pulse power discharge can decrease the size of soy beans powder a few times. Another advantage of such experiments was that the pulse power discharge killed bacteria and viruses. After our experiments we did not observe mold growing. Using pulse power discharge we can decrease sinking speed by about ten times. Ultra sound generation is useful and can decrease sinking speed even more, compared with pulse power discharge.

  8. A study of the glow discharge plasma jet of the novel Hamburger-electrode

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Wenzheng, E-mail: wzhliu@bjtu.edu.cn; Ma, Chuanlong, E-mail: 15121452@bjtu.edu.cn; Yang, Xiao; Cui, Weisheng; Chen, Xiuyang [School of Electrical Engineering, Beijing Jiaotong University, Beijing 100044 (China)

    2016-08-15

    To generate atmospheric pressure glow discharge plasma jets (APGDPJs), a novel Hamburger-electrode was proposed. Through the study on electric field distributions, flow field distributions, and characteristics of the discharge and jet, we found that adopting the mode of dielectric barrier discharge with non-uniform thickness of dielectric, it was easy to form the strong electric field areas which were conducive to generate discharge and electric field distributions with large electric field intensity in the narrow gap and weak electric field intensity in the wide gap that were not inclined to form a filament discharge. Using the structure of evenly distributed inner electrodes, it was easy to weaken the pressure of strong electric field areas and form flow field distributions which is beneficial for taking out the high density charged particles and generating APGDPJs. Stable APGDPJs in nitrogen with 3.5 mm in diameter and 9 mm in length were formed by using the novel Hamburger-electrode.

  9. Core-SOL simulations of L-mode tokamak plasma discharges using BALDUR code

    Directory of Open Access Journals (Sweden)

    Yutthapong Pinanroj

    2014-04-01

    Full Text Available Core-SOL simulations were carried out of plasma in tokamak reactors operating in a low confinement mode (L-mode, for various conditions that match available experimental data. The simulation results were quantitatively compared against experimental data, showing that the average RMS errors for electron temperature, ion temperature, and electron density were lower than 16% or less for 14 L-mode discharges from two tokamaks named DIII-D and TFTR. In the simulations, the core plasma transport was described using a combination of neoclassical transport calculated by NCLASS module and anomalous transport by Multi-Mode-Model version 2001 (MMM2001. The scrape-off-layer (SOL is the small amount of residual plasma that interacts with the tokamak vessel, and was simulated by integrating the fluid equations, including sources, along open field lines. The SOL solution provided the boundary conditions of core plasma region on low confinement mode (L-mode. The experimental data were for 14 L-mode discharges and from two tokamaks, named DIII-D and TFTR.

  10. Flame Structure and Chemiluminescence Emissions of Inverse Diffusion Flames under Sinusoidally Driven Plasma Discharges

    Directory of Open Access Journals (Sweden)

    Maria Grazia De Giorgi

    2017-03-01

    Full Text Available Reduction of nitric oxides (NOx in aircraft engines and in gas turbines by lean combustion is of great interest in the design of novel combustion systems. However, the stabilization of the flame under lean conditions is a main issue. In this context, the present work investigates the effects of sinusoidal dielectric barrier discharge (DBD on a lean inverse diffusive methane/air flame in a Bunsen-type burner under different actuation conditions. The flame appearance was investigated with fixed methane loading (mass flux, but with varying inner airflow rate. High-speed flame imaging was done by using an intensified (charge-coupled device CCD camera equipped with different optical filters in order to selectively record signals from the chemiluminescent species OH*, CH*, or CO2* to evaluate the flame behavior in presence of plasma actuation. The electrical power consumption was less than 33 W. It was evident that the plasma flame enhancement was significantly influenced by the plasma discharges, particularly at high inner airflow rates. The flame structure changes drastically when the dissipated plasma power increases. The flame area decreases due to the enhancement of mixing and chemical reactions that lead to a more anchored flame on the quartz exit with a reduction of the flame length.

  11. Experimental behaviour of a argon plasma, which is passed by a high current intensity, with different magnetic field configurations; Comportamiento experimental de un plasma de argon en diferentes configuraciones de campo magnetico y a elevadas corrientes

    Energy Technology Data Exchange (ETDEWEB)

    Lozano, J.

    1964-07-01

    In a lineal discharge, the longitudinal and azimuthal magnetic fields produced by the current through the tube and the returning conductors, which have 4 different forms, are determined with a magnetic probe, which has a radial and longitudinal displacement. The plasma is produced discharging a 135{mu}F and 9 KV capacitor bank through Argon at 10{sup -}1 Torr. (Author) 5 refs.

  12. Faraday Accelerator With Radio-Frequency Assisted Discharge (FARAD): A New Electrodeless Concept for Plasma Propulsion

    National Research Council Canada - National Science Library

    Choueiri, Edgar; Pozin, Kurt; Hallock, Ashley

    2008-01-01

    .... The primary advantage of this concept is that a preionized plasma is employed to lower the initial voltage threshold which applies to the formation of an inductive current sheet in other pulsed...

  13. Effect of duty-cycles on the air plasma gas-phase of dielectric barrier discharges

    Science.gov (United States)

    Barni, R.; Biganzoli, I.; Dell'Orto, E. C.; Riccardi, C.

    2015-10-01

    An experimental investigation concerning the effects of a duty-cycle in the supply of a dielectric barrier discharge in atmospheric pressure air has been performed. Electrical characteristics of the discharge have been measured, focusing mainly on the statistical properties of the current filaments and on dielectric surface charging, both affected by the frequent repetition of breakdown imposed by the duty-cycle. Information on the gas-phase composition was gathered too. In particular, a strong enhancement in the ozone formation rate is observed when suitable long pauses separate the active discharge phases. A simulation of the chemical kinetics in the gas-phase, based on a simplified discharge modeling, is briefly described in order to shed light on the observed increase in ozone production. The effect of a duty-cycle on surface modification of polymeric films in order to increase their wettability has been investigated too.

  14. Surface treatment of para-aramid fiber by argon dielectric barrier discharge plasma at atmospheric pressure

    Science.gov (United States)

    Gu, Ruxi; Yu, Junrong; Hu, Chengcheng; Chen, Lei; Zhu, Jing; Hu, Zuming

    2012-10-01

    This paper is focused on influence of argon dielectric barrier discharge (DBD) plasma on the adhesive performance and wettability of para-aramid fibers and three parameters including treated power, exposure time and argon flux were detected. The interfacial shear strength (IFSS) was greatly increased by 28% with 300 W, 60 s, 2 L min-1 argon flux plasma treatment. The content of oxygen atom and oxygen-containing polar functional groups were enhanced after the argon plasma treated, so as the surface roughness, which contributed to the improvement of surface wettability and the decrease of contact angle with water. However, long-time exposure, exorbitant power or overlarge argon flux could partly destroy the prior effects of the treatment and damage the mechanical properties of fibers to some degree.

  15. A volume averaged global model for inductively coupled HBr/Ar plasma discharge

    Science.gov (United States)

    Chung, Sang-Young; Kwon, Deuk-Chul; Choi, Heechol; Song, Mi-Young

    2015-09-01

    A global model for inductively coupled HBr/Ar plasma was developed. The model was based on a self-consistent global model had been developed by Kwon et al., and a set of chemical reactions in the HBr/Ar plasma was compiled by surveying theoretical, experimental and evaluative researches. In this model vibrational excitations of bi-atomic molecules and electronic excitations of hydrogen atom were taken into account. Neutralizations by collisions between positive and negative ions were considered with Hakman's approximate formula achieved by fitting of theoretical result. For some reactions that were not supplied from literatures the reaction parameters of Cl2 and HCl were adopted as them Br2 and HBr, respectively. For validation calculation results using this model were compared with experimental results from literatures for various plasma discharge parameters and it showed overall good agreement.

  16. Plasma chemistry in an atmospheric pressure Ar/NH3 dielectric barrier discharge

    DEFF Research Database (Denmark)

    Fateev, A.; Leipold, F.; Kusano, Y.

    2005-01-01

    absorption spectroscopy was also employed for the detection of stable products in the exhaust gas. To clarify the different processes for ammonia decomposition, N-2(2 - 10%) was added to the plasma. Modeling of the chemical kinetics in an Ar/NH3 plasma was performed as well. The dominant stable products...... of an atmospheric pressure Ar/NH3 DBD are H-2, N-2 and N2H4. The hydrazine (N2H4) concentration in the plasma and in the exhaust gases at various ammonia concentrations and different discharge powers was measured. Thermal N2H4 decomposition into NH2 radicals may be used for NOx reduction processes....

  17. Analysis of shot-to-shot variability in post-disruption runaway electron currents for diverted DIII-D discharges

    Science.gov (United States)

    Izzo, V. A.; Humphreys, D. A.; Kornbluth, M.

    2012-09-01

    In DIII-D experiments, rapid termination by Ar-pellet injection sometimes produces a post-termination runaway electron (RE) current plateau, but this effect is highly non-reproducible on a shot-to-shot basis, particularly for diverted target plasmas. A set of DIII-D discharges is analyzed with two MHD codes to understand the relationship between the current profile of the target plasma and the amplitude of the RE current plateau. Using the linear stability code GATO, a correlation between the radial profile of the unstable n = 1 mode just after Ar-pellet injection and the observed appearance of an RE plateau is identified. Nonlinear NIMROD simulations with RE test-particle calculations directly predict RE confinement times during the disruption. With one exception, NIMROD predicts better RE confinement for shots in which higher RE currents were observed in DIII-D. But, the variation in confinement is primarily connected to the saturated n = 1 mode amplitude and not its radial profile. Still, both sets of analyses support the hypothesis that RE deconfinement by MHD fluctuations is a major factor in the shot-to-shot variability of RE plateaus, though additional factors such as seed current amplitude cannot be ruled out.

  18. Synergistic effect of electrical and chemical factors on endocytosis in micro-discharge plasma gene transfection

    Science.gov (United States)

    Jinno, M.; Ikeda, Y.; Motomura, H.; Isozaki, Y.; Kido, Y.; Satoh, S.

    2017-06-01

    We have developed a new micro-discharge plasma (MDP)-based gene transfection method, which transfers genes into cells with high efficiency and low cytotoxicity; however, the mechanism underlying the method is still unknown. Studies revealed that the N-acetylcysteine-mediated inhibition of reactive oxygen species (ROS) activity completely abolished gene transfer. In this study, we used laser-produced plasma to demonstrate that gene transfer does not occur in the absence of electrical factors. Our results show that both electrical and chemical factors are necessary for gene transfer inside cells by microplasma irradiation. This indicates that plasma-mediated gene transfection utilizes the synergy between electrical and chemical factors. The electric field threshold required for transfection was approximately 1 kV m-1 in our MDP system. This indicates that MDP irradiation supplies sufficient concentrations of ROS, and the stimulation intensity of the electric field determines the transfection efficiency in our system. Gene transfer by plasma irradiation depends mainly on endocytosis, which accounts for at least 80% of the transfer, and clathrin-mediated endocytosis is a dominant endocytosis. In plasma-mediated gene transfection, alterations in electrical and chemical factors can independently regulate plasmid DNA adhesion and triggering of endocytosis, respectively. This implies that plasma characteristics can be adjusted according to target cell requirements, and the transfection process can be optimized with minimum damage to cells and maximum efficiency. This may explain how MDP simultaneously achieves high transfection efficiency with minimal cell damage.

  19. Comparison Between Dielectric Barrier Discharge Plasma and Ozone Regenerations of Activated Carbon Exhausted with Pentachlorophenol

    Science.gov (United States)

    Qu, Guangzhou; Liang, Dongli; Qu, Dong; Huang, Yimei; Li, Jie

    2014-06-01

    In this study, two regeneration methods (dielectric barrier discharge (DBD) plasma and ozone (O3) regeneration) of saturated granular activated carbon (GAC) with pentachlorophenol (PCP) were compared. The results show that the two regeneration methods can eliminate contaminants from GAC and recover its adsorption properties to some extent. Comparing the DBD plasma with O3 regeneration, the adsorption rate and the capacity of the GAC samples after DBD plasma regeneration are greater than those after O3 regeneration. O3 regeneration decreases the specific surface area of GAC and increases the acidic surface oxygen groups on the surface of GAC, which causes a decrease in PCP on GAC uptake. With increasing regeneration cycles, the regeneration efficiencies of the two methods decrease, but the decrease in the regeneration efficiencies of GAC after O3 regeneration is very obvious compared with that after DBD plasma regeneration. Furthermore, the equilibrium data were fitted by the Freundlich and Langmuir models using the non-linear regression technique, and all the adsorption equilibrium isotherms fit the Langmuir model fairly well, which demonstrates that the DBD plasma and ozone regeneration processes do not appear to modify the adsorption process, but to shift the equilibrium towards lower adsorption concentrations. Analyses of the weight loss of GAC show that O3 regeneration has a lower weight loss than DBD plasma regeneration.

  20. Modification of polyethylene terephthalate (PET) films surface with gradient roughness and homogenous surface chemistry by dielectric barrier discharge plasma

    Science.gov (United States)

    Gao, Ming; Sun, Liqun; Guo, Ying; Shi, Jianjun; Zhang, Jing

    2017-12-01

    Dielectric barrier discharge (DBD) plasma was used to modify polyethylene terephthalate (PET) films with gradient roughness and homogenous surface chemistry. Based on asymmetric electrode arrangement, the spatial distribution of the plasma on the films surface was non-uniform, leading to the formation of typical three discharge regions (central zone, boundary zone and diffuse zone). The experimental results showed that the plasma induced significant morphological and chemical changes onto the surfaces. Furthermore, a gradient surface roughness from central zone to diffuse zone was formed, while surface chemistry was relatively homogenous in these regions, which can be explained by theoretical plasma-etching mechanism.

  1. Breakdown in helium in high-voltage open discharge with subnanosecond current front rise

    Energy Technology Data Exchange (ETDEWEB)

    Schweigert, I. V., E-mail: ischweig@itam.nsc.ru; Alexandrov, A. L. [Russian Academy of Sciences, Khristianovich Institute of Theoretical and Applied Mechanics, Siberian Branch (Russian Federation); Bokhan, P. A.; Zakrevskiy, Dm. E. [Russian Academy of Sciences, Rzhanov Institute of Semiconductors Physics, Siberian Branch (Russian Federation)

    2016-07-15

    Investigations of high-voltage open discharge in helium have shown a possibility of generation of current pulses with subnanosecond front rise, due to ultra-fast breakdown development. The open discharge is ignited between two planar cathodes with mesh anode in the middle between them. For gas pressure 6 Torr and 20 kV applied voltage, the rate of current rise reaches 500 A/(cm{sup 2} ns) for current density 200 A/cm{sup 2} and more. The time of breakdown development was measured for different helium pressures and a kinetic model of breakdown in open discharge is presented, based on elementary reactions for electrons, ions and fast atoms. The model also includes various cathode emission processes due to cathode bombardment by ions, fast atoms, electrons and photons of resonant radiation with Doppler shift of frequency. It is shown, that the dominating emission processes depend on the evolution of the discharge voltage during the breakdown. In the simulations, two cases of voltage behavior were considered: (i) the voltage is kept constant during the breakdown; (ii) the voltage is reduced with the growth of current. For the first case, the exponentially growing current is maintained due to photoemission by the resonant photons with Doppler-shifted frequency. For the second case, the dominating factor of current growth is the secondary electron emission. In both cases, the subnanosecond rise of discharge current was obtained. Also the effect of gas pressure on breakdown development was considered. It was found that for 20 Torr gas pressure the time of current rise decreases to 0.1 ns, which is in agreement with experimental data.

  2. Current-Driven Filament Instabilities in Relativistic Plasmas. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Ren, Chuang

    2013-02-13

    This grant has supported a study of some fundamental problems in current- and flow-driven instabilities in plasmas and their applications in inertial confinement fusion (ICF) and astrophysics. It addressed current-driven instabilities and their roles in fast ignition, and flow-driven instabilities and their applications in astrophysics.

  3. Currents between tethered electrodes in a magnetized laboratory plasma

    Science.gov (United States)

    Stenzel, R. L.; Urrutia, J. M.

    1989-01-01

    Laboratory experiments on important plasma physics issues of electrodynamic tethers were performed. These included current propagation, formation of wave wings, limits of current collection, nonlinear effects and instabilities, charging phenomena, and characteristics of transmission lines in plasmas. The experiments were conducted in a large afterglow plasma. The current system was established with a small electron-emitting hot cathode tethered to an electron-collecting anode, both movable across the magnetic field and energized by potential difference up to V approx.=100 T(sub e). The total current density in space and time was obtained from complete measurements of the perturbed magnetic field. The fast spacecraft motion was reproduced in the laboratory by moving the tethered electrodes in small increments, applying delayed current pulses, and reconstructing the net field by a linear superposition of locally emitted wavelets. With this technique, the small-amplitude dc current pattern is shown to form whistler wings at each electrode instead of the generally accepted Alfven wings. For the beam electrode, the whistler wing separates from the field-aligned beam which carries no net current. Large amplitude return currents to a stationary anode generate current-driven microinstabilities, parallel electric fields, ion depletions, current disruptions and time-varying electrode charging. At appropriately high potentials and neutral densities, excess neutrals are ionized near the anode. The anode sheath emits high-frequency electron transit-time oscillations at the sheath-plasma resonance. The beam generates Langmuir turbulence, ion sound turbulence, electron heating, space charge fields, and Hall currents. An insulated, perfectly conducting transmission line embedded in the plasma becomes lossy due to excitation of whistler waves and magnetic field diffusion effects. The implications of the laboratory observations on electrodynamic tethers in space are discussed.

  4. Functionalization of Hydrogen-free Diamond-like Carbon Films using Open-air Dielectric Barrier Discharge Atmospheric Plasma Treatments

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence Berkeley National Laboratory, Berkeley, CA 94720, USA; Instituto de Materiales de Madrid, C.S.I.C., Cantoblanco, 28049 Madrid, Spain; Instituto de Quimica-Fisica" Rocasolano" C.S.I.C., 28006 Madrid, Spain; Mahasarakham University, Mahasarakham 44150, Thailand; CASTI, CNR-INFM Regional Laboratory, L' Aquila 67100, Italy; SUNY Upstate Medical University, Syracuse, NY 13210, USA; Endrino, Jose; Endrino, J. L.; Marco, J. F.; Poolcharuansin, P.; Phani, A.R.; Allen, M.; Albella, J. M.; Anders, A.

    2007-12-28

    A dielectric barrier discharge (DBD) technique has been employed to produce uniform atmospheric plasmas of He and N2 gas mixtures in open air in order to functionalize the surface of filtered-arc deposited hydrogen-free diamond-like carbon (DLC) films. XPS measurements were carried out on both untreated and He/N2 DBD plasma treated DLC surfaces. Chemical states of the C 1s and N 1s peaks were collected and used to characterize the surface bonds. Contact angle measurements were also used to record the short- and long-term variations in wettability of treated and untreated DLC. In addition, cell viability tests were performed to determine the influence of various He/N2 atmospheric plasma treatments on the attachment of osteoblast MC3T3 cells. Current evidence shows the feasibility of atmospheric plasmas in producing long-lasting variations in the surface bonding and surface energy of hydrogen-free DLC and consequently the potential for this technique in the functionalization of DLC coated devices.

  5. A self-discharge model of Lithium-Sulfur batteries based on direct shuttle current measurement

    Science.gov (United States)

    Knap, Vaclav; Stroe, Daniel-Ioan; Swierczynski, Maciej; Purkayastha, Rajlakshmi; Propp, Karsten; Teodorescu, Remus; Schaltz, Erik

    2016-12-01

    In the group of post Lithium-ion batteries, Lithium-Sulfur (Li-S) batteries attract a high interest due to their high theoretical limits of the specific capacity of 1672 Ah kg-1 and specific energy of around 2600 Wh kg-1. However, they suffer from polysulfide shuttle, a specific phenomenon of this chemistry, which causes fast capacity fade, low coulombic efficiency, and high self-discharge. The high self-discharge of Li-S batteries is observed in the range of minutes to hours, especially at a high state of charge levels, and makes their use in practical applications and testing a challenging process. A simple but comprehensive mathematical model of the Li-S battery cell self-discharge based on the shuttle current was developed and is presented. The shuttle current values for the model parameterization were obtained from the direct shuttle current measurements. Furthermore, the battery cell depth-of-discharge values were recomputed in order to account for the influence of the self-discharge and provide a higher accuracy of the model. Finally, the derived model was successfully validated against laboratory experiments at various conditions.

  6. Plasma Shape and Current Density Profile Control in Advanced Tokamak Operating Scenarios

    Science.gov (United States)

    Shi, Wenyu

    -point position. Setting up a suitable toroidal current profile is related to both the stability and performance of the plasma. The requirements of ITER motivate the research on plasma current profile control. Currently, physics-based control-oriented modeling techniques of the current profile evolution can be separated into two major classes: data-driven and first-principles-driven. In this dissertation, a two-timescale linear dynamic data-driven model of the rotational transform profile and betaN is identified based on experimental data from the DIII-D tokamak. A mixed-sensitivity Hinfinity controller is developed and tested during DIII-D high-confinement (H-mode) experiments by using the heating and current drive (H&CD) systems to regulate the plasma rotational transform profile and betaN around particular target values close to the reference state used for system identification. The preliminary experimental results show good progress towards routine current profile control in DIII-D. As an alternative, a nonlinear dynamic first-principles-driven model is obtained by converting the physics-based model that describes the current profile evolution in H-mode DIII-D discharges into a form suitable for control design. The obtained control-oriented model is validated by comparing the model prediction to experimental data. An Hinfinity control design problem is formulated to synthesize a stabilizing feedback controller, with the goal of developing a closed-loop controller to drive the current profile in DIII-D to a desirable target evolution. Simulations show that the controller is capable of regulating the system around the target rotational transform profile in the presence of disturbances. When compared to a previously designed data-driven model-based controller, the proposed first-principles-driven model-based controller shows potential for improving the control performance.

  7. Plasma Kinetics in Electrical Discharge in Mixture of Air, Water and Ethanol Vapors for Hydrogen Enriched Syngas Production

    OpenAIRE

    Shchedrin, A. I.; Levko, D. S.; Ryabtsev, A. V.; Chernyak, V. Ya.; Yukhymenko, V. V.; Olszewski, S. V.; Naumov, V. V.; Prysiazhnevych, I. V.; Solomenko, E. V.; Demchina, V. P.; Kudryavtsev, V. S.

    2008-01-01

    The complex theoretical and experimental investigation of plasma kinetics of the electric discharge in the mixture of air and ethanol-water vapors is carried out. The discharge was burning in the cavity, formed by air jets pumping between electrodes, placed in aqueous ethanol solution. It is found out that the hydrogen yield from the discharge is maximal in the case when ethanol and water in the solution are in equal amounts. It is shown that the hydrogen production increases with the dischar...

  8. Purification of water by bipolar pulsed discharge plasma combined with TiO2 catalysis

    Science.gov (United States)

    Zhang, Yongrui; Zhang, Ruobing; Ma, Wenchang; Zhang, Xian; Wang, Liming; Guan, Zhicheng

    2013-03-01

    In the process of water treatment by bipolar pulsed discharge plasma, there are not only the chemical effects such as the cold plasma, but also the physical effects such as the optical radiation. The energy of the optical radiation can be used by photocatalyst. Therefore, the effect of the photocatalyst to the degradation of the organic pollutant was investigated using a packed bed reactor by bipolar pulsed discharge in the air-liquid-solid mixture. The nanoparticle TiO2 photocatalyst was obtained using the sol-gel method and the typical dye solution Indigo Carmine was chosen as the degradation target to test the catalytic effect of the nanoparticle TiO2 photocatalyst. Experiment results proved that the degradation efficiency of the Indigo Carmine solution was increased by a certain extent with the TiO2 photocatalyst. It was totally decolorized within 3 minutes by bipolar pulsed discharge in the condition that the peak voltage was 30 kV and the air flow was 1.0 m3 h-1.

  9. Rydberg gas theory of a glow discharge plasma: III. Formation, occupied state distributions, free energy, and kinetic control.

    Science.gov (United States)

    Mason, Rod S; Douglas, Peter

    2010-04-21

    It has been suggested that Rydberg gas atoms are involved in conducting electricity through a steady state flowing afterglow (FAG) discharge plasma (R. S. Mason, D. J. Mitchell and P. M. Dickinson, Phys. Chem. Chem. Phys., 2010, DOI: ). From known properties of Rydberg atoms, a statistical model is developed here to find the distribution of levels (principal quantum number n) occupied in such a hypothetical Rydberg gas. It behaves non-ideally at positive column plasma densities, predicting 30 states are very long-lived and almost completely separated from the low n states by the low probability of intermediate levels. The effects of Rydberg gas (N(R)) and free charge densities are examined. The gas can exist in a deep free energy well (> 120 kJ mol(-1) below ionisation level when 10(10) collision and deceleration at the opposite NG-Positive Column (PC) plasma boundary. The atoms become stabilized after passing into the PC, by collisionally induced (nlm) mixing of states and the removal of free charge by charge transfer (and hence the passage of electric current through the Rydberg gas). The coupling of Rydberg states with the ionization continuum is poor; therefore, if the rate of their charge transfer is greater than that of their ionization, the Rydberg gas will remain relatively charge free and hence stable when it is conducting a current. When applied to the FAG plasma, the model provides a self-consistent interpretive framework for all its electrical, mass spectrometric and chemical behaviour. The effect on the optical spectroscopy of these plasmas is considered briefly.

  10. Effect of individual discharge cascades on the microstructure of plasma electrolytic oxidation coatings

    Energy Technology Data Exchange (ETDEWEB)

    Troughton, S.C. [Department of Materials Science & Metallurgy, Cambridge Universitym 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Nominé, A. [Department of Physical Sciences, Open University, Walton Hall, Milton Keynes MK7 6AA (United Kingdom); Dean, J. [Department of Materials Science & Metallurgy, Cambridge Universitym 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Clyne, T.W., E-mail: twc10@cam.ac.uk [Department of Materials Science & Metallurgy, Cambridge Universitym 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom)

    2016-12-15

    Highlights: • High speed current/video monitoring of discharge cascades. • SEM and X-ray Computed Tomography of cascade sites. • Effects of supply frequency and process interruption. • Explanation of cascade localisation. - Abstract: Short duration (∼1 s) PEO treatments have been applied to aluminium alloy samples on which coatings of thickness ∼100 μm had previously been created. This was done using the small area electrical monitoring system previously developed in the Gordon Laboratory in Cambridge. Voltage supply frequencies of 50 Hz and 2.5 kHz were employed. Fairly high resolution SEM micrographs were taken, covering the whole surface of small area samples (ie over a circular area of diameter about 0.9 mm). This was done both before and after the 1 s PEO treatments. X-ray tomographic data were also obtained in the vicinity of a recently-completed set of discharges. The outcomes of these observations were correlated with synchronised high speed electrical monitoring and video photography, carried out during the PEO treatment periods. Localised cascades (comprising hundreds of individual discharges) were observed in all cases, persisting throughout the 1 s periods and also reappearing in the same location when a second 1 s PEO treatment was applied to the same sample. This repetition of discharges at the same location is apparently due to the deep pores associated with these sites, creating a pathway of low electrical resistance, even after appreciable oxidation has occurred in the vicinity. Observations were made of the way in which the surfaces were reconstructed locally as discharge cascades occurred. With the high frequency voltage supply, discharge lifetimes were limited to the half-cycle period (of 200 μs), but in other respects the cascades were similar to those with the lower frequency. However, some discharges occurred during cathodic half-cycles with the high frequency supply, at the same location as the anodic discharges in the cascade

  11. Preliminary scaling laws for plasma current, ion kinetic temperature, and plasma number density in the NASA Lewis bumpy torus plasma

    Science.gov (United States)

    Roth, J. R.

    1976-01-01

    Parametric variation of independent variables which may affect the characteristics of bumpy torus plasma have identified those which have a significant effect on the plasma current, ion kinetic temperature, and plasma number density, and those which do not. Empirical power law correlations of the plasma current, and the ion kinetic temperature and number density were obtained as functions of potential applied to the midplane electrode rings, the background neutral gas pressure, and the magnetic field strength. Additional parameters studied included the type of gas, the polarity of the midplane electrode rings, the mode of plasma operation, and the method of measuring the plasma number density. No significant departures from the scaling laws appear to occur at the highest ion kinetic temperatures or number densities obtained to date.

  12. Catalytic-Dielectric Barrier Discharge Plasma Reactor For Methane and Carbon Dioxide Conversion

    Directory of Open Access Journals (Sweden)

    Istadi Istadi

    2007-10-01

    Full Text Available A catalytic - DBD plasma reactor was designed and developed for co-generation of synthesis gas and C2+ hydrocarbons from methane. A hybrid Artificial Neural Network - Genetic Algorithm (ANN-GA was developed to model, simulate and optimize the reactor. Effects of CH4/CO2 feed ratio, total feed flow rate, discharge voltage and reactor wall temperature on the performance of catalytic DBD plasma reactor was explored. The Pareto optimal solutions and corresponding optimal operating parameters ranges based on multi-objectives can be suggested for catalytic DBD plasma reactor owing to two cases, i.e. simultaneous maximization of CH4 conversion and C2+ selectivity, and H2 selectivity and H2/CO ratio. It can be concluded that the hybrid catalytic DBD plasma reactor is potential for co-generation of synthesis gas and higher hydrocarbons from methane and carbon dioxide and showed better than the conventional fixed bed reactor with respect to CH4 conversion, C2+ yield and H2 selectivity for CO2 OCM process. © 2007 BCREC UNDIP. All rights reserved.[Presented at Symposium and Congress of MKICS 2007, 18-19 April 2007, Semarang, Indonesia][How to Cite: I. Istadi, N.A.S. Amin. (2007. Catalytic-Dielectric Barrier Discharge Plasma Reactor For Methane and Carbon Dioxide Conversion. Bulletin of Chemical Reaction Engineering and Catalysis, 2 (2-3: 37-44.  doi:10.9767/bcrec.2.2-3.8.37-44][How to Link/DOI: http://dx.doi.org/10.9767/bcrec.2.2-3.8.37-44 || or local: http://ejournal.undip.ac.id/index.php/bcrec/article/view/8][Cited by: Scopus 1 |

  13. Spectroscopic studies of plasma in a carbon arc discharge for synthesis of nanomaterials

    Science.gov (United States)

    Vekselman, Vladislav; Feurer, Matthew; Yeh, Yao-Wen; Stratton, Brentley; Raitses, Yevgeny; LaboratoryPlasma Nanosynthesis Team

    2016-09-01

    An atmospheric pressure arc discharge with graphite electrodes is commonly used for synthesis of carbon nanomaterials such as buckyballs, nanotubes and graphene. In operation, the graphite anode ablates providing a feedstock material for synthesis these carbon nanostructures. Existing models predict that nucleation and growth of these nanomaterials in an arc discharge are governed by spatial distributions of density and temperature of plasma species. Control of these distributions can potentially enable optimization of nanosynthesis processes, to achieve the best combination of synthesis selectivity at the synthesis yield. In this work, we report first detail measurements of spatial distribution of arc plasma parameters obtained with a set of in-situ diagnostics, including optical emission spectroscopy and fast framing imaging. These parameters were measured in low- and high- anode ablation modes. Results of these measurements demonstrate a strong correlation between arc plasma and synthesis processes. This work was supported by U.S. Department of Energy, Office of Science, Basic Sciences, Materials Sciences and Engineering Division.

  14. Deflagration of Energetic Materials Initiated by Electrostatic Discharges and Laser-Induced Plasmas

    Science.gov (United States)

    Collins, Eric; Gottfried, Jennifer

    2017-06-01

    A laser-induced plasma and an electrostatic discharge were used for the ignition of small quantities (5-10 mg) of energetic materials. The laser-induced plasma was generated from a ns-pulsed Nd:YAG laser with energy output of 0.8 J per pulse and the electrostatic discharge was generated from a 0.035 μF capacitor that was charged to energy levels of up to 10 J. Although the durations and energy outputs of these two ignition mechanisms are very different, similarities in the initiation of the energetic materials include particle ejection from the target, heating of particles in the air from the plasma and spark, and a shockwave formation. The shock wave was measured and analyzed at various energy levels using schlieren imaging with a high speed camera. Diagnostics used to measure time-resolved temperatures, energy generation, and emission signatures of the deflagrations were high speed camera pyrometry, visible and infrared photo receivers, and a high-resolution spectrometer, respectively.

  15. Evaluation of pathogen inactivation on sliced cheese induced by encapsulated atmospheric pressure dielectric barrier discharge plasma.

    Science.gov (United States)

    Yong, Hae In; Kim, Hyun-Joo; Park, Sanghoo; Alahakoon, Amali U; Kim, Kijung; Choe, Wonho; Jo, Cheorun

    2015-04-01

    Pathogen inactivation induced by atmospheric pressure dielectric barrier discharge (DBD) (250 W, 15 kHz, air discharge) produced in a rectangular plastic container and the effect of post-treatment storage time on inactivation were evaluated using agar plates and cheese slices. When agar plates were treated with plasma, populations of Escherichia coli, Salmonella Typhimurium, and Listeria monocytogenes showed 3.57, 6.69, and 6.53 decimal reductions at 60 s, 45 s, and 7 min, respectively. When the pathogens tested were inoculated on cheese slices, 2.67, 3.10, and 1.65 decimal reductions were achieved at the same respective treatment times. The post-treatment storage duration following plasma treatment potently affected further reduction in pathogen populations. Therefore, the newly developed encapsulated DBD-plasma system for use in a container can be applied to improve the safety of sliced cheese, and increasing post-treatment storage time can greatly enhance the system's pathogen-inactivation efficiency. Copyright © 2014 Elsevier Ltd. All rights reserved.

  16. Plasma monitoring of nanoparticles formation in SiH4/H2 discharges

    Science.gov (United States)

    Alexiou, Giannis; Tsigaras, Giannis; Amanatides, Eleftherios; Mataras, Dimitrios; Plasma Technology Laboratory-Department of Chemical Engineering-University of Patras Team

    2016-09-01

    Radio-frequency SiH4/H2 discharges is the most common technique for the growth of silicon thin films. Nanoparticles formation and uncontrollable agglomeration to dust is common drawback of such type of discharges due to the extensive reactivity of the species produced in the gas phase. In this work, we deposited silicon films in different plasma conditions while monitoring at the same time nanoparticles formation. The experiments were performed under Continuous Wave (CW) and Pulsed Plasma generation in order to control particles formation. Different time-resolved plasma diagnostics, such as Optical Emission Imaging, Laser Light Scattering and self-bias voltage (Vdc) measurements were used for the detection of particles. Mass spectrometry was also used to record higher silanes formation during the deposition. The deposited films were characterized in terms of crystallinity, hydrogen content and optical properties by Laser Raman, Fourier Transformed Infrared and UV/Vis spectroscopy. Finally, Atomic Force Microscopy (AFM) was applied to monitor the morphology and roughness of the films. The properties and the morphology of the deposited films are compared in order to determine the effect of the particles formation on the material's quality.

  17. Enhancement of the plasma chemistry process in a three-phase discharge reactor

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Ruobing; Wu Yan; Li Guofeng [Institute of Electrostatics and Special Power, Dalian University of Technology, Dalian, 116023 (China)

    2005-05-01

    The influence of solid packing on the chemical process involved in the solid-liquid-gas three-phase discharge plasma reactor, initiated by a bipolar pulsed power source was studied with indigo carmine (indigo-5,5'-disulfonic acid, IDS) as the probe. Dynamic scanning of the UV-Vis absorption spectrum was used as the analysis method. Experimental results show that addition of solid packing into the water-air two-phase discharge plasma reactor enhances the chemical processes in the reactor. The dielectric properties of the packing materials determine the degree of enhancement. Water treatment performance of the reactor with dielectric spheres is much better than that with conducting materials for the same experimental conditions. In addition, dielectric glass beads have a stronger influence on the chemical enhancement process than ceramic spheres. Decolourization of IDS in the plasma reactor with dielectric packing is a pseudo-first-order reaction. The total organic carbon in the solution decreases during the treatment process.

  18. Saturated Resin Ectopic Regeneration by Non-Thermal Dielectric Barrier Discharge Plasma

    Directory of Open Access Journals (Sweden)

    Chunjing Hao

    2017-11-01

    Full Text Available Textile dyes are some of the most refractory organic compounds in the environment due to their complex and various structure. An integrated resin adsorption/Dielectric Barrier Discharge (DBD plasma regeneration was proposed to treat the indigo carmine solution. It is the first time to report ectopic regeneration of the saturated resins by non-thermal Dielectric Barrier Discharge. The adsorption/desorption efficiency, surface functional groups, structural properties, regeneration efficiency, and the intermediate products between gas and liquid phase before and after treatment were investigated. The results showed that DBD plasma could maintain the efficient adsorption performance of resins while degrading the indigo carmine adsorbed by resins. The degradation rate of indigo carmine reached 88% and the regeneration efficiency (RE can be maintained above 85% after multi-successive regeneration cycles. The indigo carmine contaminants were decomposed by a variety of reactive radicals leading to fracture of exocyclic C=C bond, which could cause decoloration of dye solution. Based on above results, a possible degradation pathway for the indigo carmine by resin adsorption/DBD plasma treatment was proposed.

  19. Synthesis and characteristics of Ag/Pt bimetallic nanocomposites by arc-discharge solution plasma processing.

    Science.gov (United States)

    Pootawang, Panuphong; Saito, Nagahiro; Takai, Osamu; Lee, Sang-Yul

    2012-10-05

    Arc discharge in solution, generated by applying a high voltage of unipolar pulsed dc to electrodes of Ag and Pt, was used as a method to form Ag/Pt bimetallic nanocomposites via electrode erosion by the effects of the electric arc at the cathode (Ag rod) and the sputtering at the anode (Pt rod). Ag/Pt bimetallic nanocomposites were formed as colloidal particles dispersed in solution via the reduction of hydrogen radicals generated during discharge without the addition of chemical precursor or reducing agent. At a discharge time of 30 s, the fine bimetallic nanoparticles with a mean particle size of approximately 5 nm were observed by transmission electron microscopy (TEM). With increasing discharge time, the bimetallic nanoparticle size tended to increase by forming an agglomeration. The presence of the relatively small amount of Pt dispersed in the Ag matrix could be observed by the analytical mapping mode of energy-dispersive x-ray spectroscopy and high-resolution TEM. This demonstrated that the synthesized particle was in the form of a nanocomposite. No contamination of other chemical substances was detected by x-ray photoelectron spectroscopy. Hence, solution plasma could be a clean and simple process to effectively synthesize Ag/Pt bimetallic nanocomposites and it is expected to be widely applicable in the preparation of several types of nanoparticle.

  20. Continuous measurements of discharge from a horizontal acoustic Doppler current profiler in a tidal river

    NARCIS (Netherlands)

    Hoitink, A.J.F.; Buschman, F.A.; Vermeulen, B.

    2009-01-01

    Acoustic Doppler current profilers (ADCPs) can be mounted horizontally at a river bank, yielding single-depth horizontal array observations of velocity across the river. This paper presents a semideterministic, semistochastic method to obtain continuous measurements of discharge from horizontal ADCP

  1. Effect of laser pulse on alternative current arc discharge during laser-arc hybrid welding of magnesium alloy

    Science.gov (United States)

    Chen, Minghua; Xin, Lijun; Zhou, Qi; He, Lijia; Wu, Fufa

    2018-01-01

    The coupling effect between a laser and arc plasma was studied in situations in which the laser acts at the positive and negative waveforms of the arc discharge during the laser-arc hybrid welding of magnesium alloy. Using the methods of direct observation, high speed imaging, and spectral analysis, the surface status of weld seams, weld penetration depths, plasma behavior, and spectral characteristics of welding plasma were investigated, respectively. Results show that, as compared with the laser pulse acting at the negative waveform of the arc plasma discharge, a better weld seam formation can be achieved when the laser pulse acts at the positive waveform of the arc discharge. At the same time, the radiation intensity of Mg atoms in the arc plasma increases significantly. However, the weld penetration depth is weaker. The findings show that when the laser pulse is acting at the negative waveform of the arc plasma discharge, the position of the arc plasma discharge on the workpiece can be restrained by the laser action point, which improves the energy density of the welding arc.

  2. Surface treatment of aramid fiber by air dielectric barrier discharge plasma at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Jia Caixia [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education) and Faculty of Chemical, Environmental and Biological Science and Technology, Dalian University of Technology, Dalian 116024 (China); Chen Ping, E-mail: chenping_898@126.com [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education) and Faculty of Chemical, Environmental and Biological Science and Technology, Dalian University of Technology, Dalian 116024 (China) and Liaoning Key Laboratory of Advanced Polymer Matrix Composites Manufacturing Technology, Shenyang Aerospace University, Shenyang 110034 (China); Liu Wei [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education) and Faculty of Chemical, Environmental and Biological Science and Technology, Dalian University of Technology, Dalian 116024 (China); Dalian University of Education, Dalian 116021 (China); Li Bin; Wang Qian [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education) and Faculty of Chemical, Environmental and Biological Science and Technology, Dalian University of Technology, Dalian 116024 (China)

    2011-02-15

    Aramid fiber samples are treated by air dielectric barrier discharge (DBD) plasma at atmospheric pressure; the plasma treatment time is investigated as the major parameter. The effects of this treatment on the fiber surface physical and chemical properties are studied by using surface characterization techniques. Scanning electron microscopy (SEM) is performed to determine the surface morphology changes, X-ray photoelectron spectroscopy (XPS) is analyzed to reveal the surface chemical composition variations and dynamic contact angle analysis (DCAA) is used to examine the changes of the fiber surface wettability. In addition, the wetting behavior of a kind of thermoplastic resin, poly(phthalazinone ether sulfone ketone) (PPESK), on aramid fiber surface is also observed by SEM photos. The study shows that there seems to be an optimum treatment condition for surface modification of aramid fiber by the air DBD plasma. In this paper, after the 12 s, 27.6 W/cm{sup 3} plasma treatment the aramid fiber surface roughness is significantly improved, some new oxygen-containing groups such as C-O, C=O and O=C-O are generated on the fiber surface and the fiber surface wettability is greatly enhanced, which results in the better wetting behavior of PPESK resin on the plasma-treated aramid fiber.

  3. Surface treatment of aramid fiber by air dielectric barrier discharge plasma at atmospheric pressure

    Science.gov (United States)

    Jia, Caixia; Chen, Ping; Liu, Wei; Li, Bin; Wang, Qian

    2011-02-01

    Aramid fiber samples are treated by air dielectric barrier discharge (DBD) plasma at atmospheric pressure; the plasma treatment time is investigated as the major parameter. The effects of this treatment on the fiber surface physical and chemical properties are studied by using surface characterization techniques. Scanning electron microscopy (SEM) is performed to determine the surface morphology changes, X-ray photoelectron spectroscopy (XPS) is analyzed to reveal the surface chemical composition variations and dynamic contact angle analysis (DCAA) is used to examine the changes of the fiber surface wettability. In addition, the wetting behavior of a kind of thermoplastic resin, poly(phthalazinone ether sulfone ketone) (PPESK), on aramid fiber surface is also observed by SEM photos. The study shows that there seems to be an optimum treatment condition for surface modification of aramid fiber by the air DBD plasma. In this paper, after the 12 s, 27.6 W/cm3 plasma treatment the aramid fiber surface roughness is significantly improved, some new oxygen-containing groups such as C-O, Cdbnd O and Odbnd C-O are generated on the fiber surface and the fiber surface wettability is greatly enhanced, which results in the better wetting behavior of PPESK resin on the plasma-treated aramid fiber.

  4. Surface treatment of para-aramid fiber by argon dielectric barrier discharge plasma at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Gu Ruxi [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, Shanghai 201620 (China); Yu Junrong, E-mail: yjr@dhu.edu.cn [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, Shanghai 201620 (China); Hu Chengcheng; Chen Lei; Zhu Jing [State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, Shanghai 201620 (China); Hu Zuming [Key Laboratory of High-performance Fibers and Products, Ministry of Education, Donghua University, Shanghai 201620 (China)

    2012-10-01

    Highlights: Black-Right-Pointing-Pointer We use DBD technique to modify the surface of Kelvar29 fibers. Black-Right-Pointing-Pointer The changed parameters include treated power, time and argon flux. Black-Right-Pointing-Pointer There exists an optimum experimental condition of plasma treatment. Black-Right-Pointing-Pointer Adhesion and wettability properties of fibers are improved through plasma treatment. - Abstract: This paper is focused on influence of argon dielectric barrier discharge (DBD) plasma on the adhesive performance and wettability of para-aramid fibers and three parameters including treated power, exposure time and argon flux were detected. The interfacial shear strength (IFSS) was greatly increased by 28% with 300 W, 60 s, 2 L min{sup -1} argon flux plasma treatment. The content of oxygen atom and oxygen-containing polar functional groups were enhanced after the argon plasma treated, so as the surface roughness, which contributed to the improvement of surface wettability and the decrease of contact angle with water. However, long-time exposure, exorbitant power or overlarge argon flux could partly destroy the prior effects of the treatment and damage the mechanical properties of fibers to some degree.

  5. Current Density and Plasma Displacement Near Perturbed Rational Surface

    Energy Technology Data Exchange (ETDEWEB)

    A.H. Boozer and N. Pomphrey

    2010-10-10

    The current density in the vicinity of a rational surface of a force-free magnetic field subjected to an ideal perturbation is shown to be the sum of both a smooth and a delta-function distribution, which give comparable currents. The maximum perturbation to the smooth current density is comparable to a typical equilibrium current density and the width of the layer in which the current flows is shown to be proportional to the perturbation amplitude. In the standard linearized theory, the plasma displacement has an unphysical jump across the rational surface, but the full theory gives a continuous displacement.

  6. Depolarization of the 4{sup 1}D{sub 2} state of a helium atom by charged particles in beam plasma discharge

    Energy Technology Data Exchange (ETDEWEB)

    Kazantsev, S.A.; Luchinkina, V.V.; Mezentsev, A.P.; Mustafaev, A.S.; Rebane, V.N.; Rys, A.G.; Stepanov, Yu.L. [St. Petersburg (Russian Federation)

    1994-06-01

    Depolarization of the 4{sup 1}D{sub 2}-2{sup 1}P{sub 1} spectra line of He atoms caused by collisions with charged particles in beam plasma discharge is investigated both experimentally and theoretically. A comparison is made between the values of the rate constant for the collisional breakdown of alignment of helium atoms in the 4{sup 1}D{sub 2} state calculated from the theory of collisional relaxation of atomic polarization moments and determined from the experimentally observed broadening of the Hanle signal contour with the increase of the beam discharge current. 23 refs., 6 figs.

  7. Thin current sheets caused by plasma flow gradients in space and astrophysical plasma

    Directory of Open Access Journals (Sweden)

    D. H. Nickeler

    2010-08-01

    Full Text Available Strong gradients in plasma flows play a major role in space and astrophysical plasmas. A typical situation is that a static plasma equilibrium is surrounded by a plasma flow, which can lead to strong plasma flow gradients at the separatrices between field lines with different magnetic topologies, e.g., planetary magnetospheres, helmet streamers in the solar corona, or at the boundary between the heliosphere and interstellar medium. Within this work we make a first step to understand the influence of these flows towards the occurrence of current sheets in a stationary state situation. We concentrate here on incompressible plasma flows and 2-D equilibria, which allow us to find analytic solutions of the stationary magnetohydrodynamics equations (SMHD. First we solve the magnetohydrostatic (MHS equations with the help of a Grad-Shafranov equation and then we transform these static equilibria into a stationary state with plasma flow. We are in particular interested to study SMHD-equilibria with strong plasma flow gradients perpendicular to separatrices. We find that induced thin current sheets occur naturally in such situations. The strength of the induced currents depend on the Alfvén Mach number and its gradient, and on the magnetic field.

  8. A refractive index gradient (RING) diagnostic for transient discharges or expansions of vapor or plasmas

    Science.gov (United States)

    Cuneo, M. E.; Lockner, T. R.; Tisone, G. S.; Bieg, K. W.; Stinnett, R. W.; Chavez, J. R.

    The use of lasers to measure plasma properties is well known. Common methods include interferometry (density), Schlieren (gradient of density), and shadowgraphy (derivative of gradient). The diagnostic described uses a fast silicon photodiode quadrant detector with a differential amplifier to temporally detect the refraction of a CW laser by transient discharges or expansions of vapor, gas or plasma. The laser beam is refracted by the gradient of the total index of refraction due to neutral and ionized atoms (positive index) and electrons (negative index) in those discharges. The output of the circuit is a voltage proportional to the deflection angle of the laser beam through the discharge. The method is a time-resolved, quantitative, species discriminating (i.e., atoms or electrons) Schlieren technique. The diagnostic is easy to field, sensitive 1.3 + or - 0.1 to 3.3 + or - 0.1 mv/mrad depending on laser power, divergence, moment arm and circuit gain) and fast (rise time = 11 (+ or -) 1 to 24 (+ or -) 1 ns depending on various circuit parameters). Diagnostic theory, and circuit design and performance is discussed. This Refractive INdex Gradient (RING) diagnostic was applied to measurements on several ion sources under development at Sandia for use on intense applied-B ion diodes in the light ion fusion program. Sources studied include different types of flashboards, a thermal evaporation lithium ion source, and a laser produced ion source. To illustrate the utility of this technique, examples of measurements on LEVIS (Laser EVaporation Ion Source), a laser produced active lithium ion source is given. Measured properties include vapor/plasma production thresholds, expansion velocities, some species information, gradient profiles, and estimates of density profiles.

  9. Transition in discharge plasma of Hall thruster type in presence of secondary electron emissive surface

    Science.gov (United States)

    Schweigert, I. V.; Yadrenkin, M. A.; Fomichev, V. P.

    2017-11-01

    Modification of the sheath structure near the emissive plate placed in magnetized DC discharge plasma of Hall thruster type was studied in the experiment and in kinetic simulations. The plate is made from Al2O3 which has enhanced secondary electron emission yield. The energetic electrons emitted by heated cathode provide the volume ionization and the secondary electron emission from the plate. An increase of the electron beam energy leads to an increase of the secondary electron generation, which initiates the transition in sheath structure over the emissive plate.

  10. Electron beam injection experiments - Replication of flight observations in a laboratory beam plasma discharge

    Science.gov (United States)

    Bernstein, W.; Mcgarity, J. O.; Konradi, A.

    1983-01-01

    Recent electron beam injection experiments in the lower ionosphere have produced two perplexing results: (1) At altitudes from 140 km to 220 km, the beam associated 391.4 nm intensity is relatively independent of altitude despite the decreasing N2 abundance. (2) The radial extent of the perturbed region populated by beam associated energetic electrons significantly exceeds the nominal gyrodiameter for 90 deg injection. A series of laboratory measurements is described in which both of these flight results appear to have been closely reproduced. The laboratory results are reasonably consistent with the transition from a collision dominated to collisionless beam-plasma discharge configuration.

  11. Slow electron energy balance for hybrid models of direct-current glow discharges

    Science.gov (United States)

    Eliseev, S. I.; Bogdanov, E. A.; Kudryavtsev, A. A.

    2017-09-01

    In this paper, we present the formulation of slow electron energy balance for hybrid models of direct current (DC) glow discharge. Electrons originating from non-local ionization (secondary) contribute significantly to the energy balance of slow electrons. An approach towards calculating effective energy brought by a secondary electron to the group of slow electrons by means of Coulomb collisions is suggested. The value of effective energy shows a considerable dependence on external parameters of a discharge, such as gas pressure, type, and geometric parameters. The slow electron energy balance was implemented into a simple hybrid model that uses analytical formulation for the description of non-local ionization by fast electrons. Simulations of short (without positive column) DC glow discharge in argon are carried out for a range of gas pressures. Comparison with experimental data showed generally good agreement in terms of current-voltage characteristics, electron density, and electron temperature. Simulations also capture the trend of increasing electron density with decreasing pressure observed in the experiment. Analysis shows that for considered conditions, the product of maximum electron density ne and electron temperature Te in negative glow is independent of gas pressure and depends on the gas type, cathode material, and discharge current. Decreasing gas pressure reduces the heating rate of slow electrons during Coulomb collisions with secondary electrons, which leads to lower values of Te and, in turn, higher maximum ne.

  12. Positive direct current corona discharges in single wire-duct electrostatic precipitators

    Directory of Open Access Journals (Sweden)

    Ashraf Yehia

    2016-05-01

    Full Text Available This paper is aimed to study the characteristics of the positive dc corona discharges in single wire-duct electrostatic precipitators. Therefore, the corona discharges were formed inside dry air fed single wire-duct reactor under positive dc voltage at the normal atmospheric conditions. The corona current-voltage characteristics curves have been measured in parallel with the ozone concentration generated inside the reactor under different discharge conditions. The corona current-voltage characteristics curves have agreed with a semi empirical equation derived from the previous studies. The experimental results of the ozone concentration generated inside the reactor were formulated in the form of an empirical equation included the different parameters that were studied experimentally. The obtained equations are valid to expect both the current-voltage characteristics curves and the corresponding ozone concentration that generates with the positive dc corona discharges inside single wire-duct electrostatic precipitators under any operating conditions in the same range of the present study.

  13. Effects of improving current characteristics of spark discharge on underwater shock waves

    Directory of Open Access Journals (Sweden)

    O Higa

    2016-09-01

    Full Text Available We have been developing a food-processing device that uses underwater shock waves generated by spark discharges at an underwater spark gap. Underwater shock waves can be used in food processing for softening, fracturing and sterilization. These technologies are attracting attention because the food is not heated during processing, so it does not change flavour. In this study, we develop a rice-powder manufacturing system using the fracturing effect provided by underwater shock waves. Because rice grains are very hard, the process must be applied repeatedly using a momentary high pressure to fracture the grains. The fast repeated generation of shock waves should provide high pressures from low energies. Therefore, we aim to achieve higher pressures from low energies expended by the underwater gap discharge. We increase the pulse compression rate by decreasing the circuit impedance of the device and increasing the charging voltage. Using optical observations and a pressure sensor, we measure the high pressure developed by the underwater shock wave and the rise time of the discharge current. We find that we can decrease the rise time of the discharge current by 17% while maintaining the peak current, and simultaneously increase the high pressure of the underwater shock wave by 135%.

  14. Influence of current and temperature on discharge characteristics of electrochemical nickel−cadmium system

    Directory of Open Access Journals (Sweden)

    Todorović Andreja

    2010-01-01

    Full Text Available The paper elaborates determination of characteristic values in the discharging process of non-hermetic nickel-cadmium galvanic battery with nominal voltage Un = 60 V and nominal capacity qn = C5 = 190 Ah and its dependence from current and temperature. Study has been performed with the set of experimental metering of voltages, electromotive force, current from discharge time range and electromotive force in steady state regime before and after battery charging. Electromotive force characteristics are obtained by using the Nernst’s equation, while the least square method was used to determine the average values of internal electrical resistivity, power losses and efficiency level. These results were used in the approximate exponential functions to determine the range dependence of the efficiency level from the internal electrical resistance of discharge current in reliance from the temperature range. Obtained results show that, in accordance to the given voltage variation of 10% Un, this type of battery holds maximal full load current of one hour capacity at the temperature of 25°C and maximal full load current of two hours capacity at the temperature of −30°C. The methodology used in the case study covers determination of the electromotive force in time range based on the metered results of values during complete battery fullness and emptiness with prior determination of equilibrium constants of galvanic battery reaction through method suggested by the author of this paper. Further process, using the electromotive force values obtained through the aforementioned process, the metered current, and approximate polynomial function of the nominal discharge voltage characteristic determines range of battery internal electric resistance from time, followed by the selection of discharge cases with average values for: voltage, electromotive force, internal electrical resistance, available and utilized power, power losses, and battery efficiency

  15. Plasma of a vacuum-arc discharge for obtaining carbon-based coatings

    Science.gov (United States)

    Pikus, M. I.; Lisenkov, A. A.; Kostrin, D. K.; Trifonov, S. A.

    2017-11-01

    Formation of the carbon films and coatings of different structural modifications can be efficiently achieved by sputtering graphite in a vacuum-arc plasma source. In this case the plasma flux is shaped in a form of a current-carrying jet with fairly distinct lateral borders. Spectral analysis shows that this plasma flux contains positively charged, excited and neutral carbon particles. In this paper is shown that for a technological cycle of deposition of a carbon-based coating it is possible to form a sublayer of the substrate material carbide, providing a possibility for the later growth of a well-formed coating.

  16. Sterilization characteristics of dental instruments using oxygen plasma produced by narrow gap RF discharge

    Science.gov (United States)

    Sakai, Yasuhiro; Liu, Zhen; Goto, Masaaki; Hayashi, Nobuya

    2016-07-01

    Sterilization characteristics and material compatibility of low-pressure RF oxygen plasma sterilization method for dental instruments are investigated. Regarding the characteristics of the plasma sterilizer for dental instruments, it is small and can rapidly sterilize owing to a narrow gap discharge. Sterilization of vial-type biological indicators is achieved for the shortest treatment period of 40 min at an RF power of 80 W at a temperature of 70 °C. At a temperature lower than 60 °C, a sterilization period of 90 min is required using a water-cooled electrode. No surface modifications of dental instruments such as chemical composition and deterioration of fine crystals of a diamond bar were observed under a scanning electron microscope.

  17. Cylindrical dielectric barrier discharge plasma catalytic effect on chemical methods of silver nano-particle production

    Science.gov (United States)

    Bahrami, Zahra; Khani, Mohammad Reza; Shokri, Babak

    2016-11-01

    In this study, cylindrical dielectric barrier discharge plasma was used to study the catalytic effect on chemical methods of silver nano-particles for the first time. In this method, the processing time is short and the temperature of reaction is low. Also, the reactor is very simple, inexpensive, and accessible. In this work, pure AgNO3 as the precursor agent and poly vinyl pyrrolidone as the macromolecular surfactant were dissolved in ethanol as the solvent. UV-Vis and XRD were used to identify the colloidal and powder nano-particles, respectively. Optical emission spectroscopy was also used to identify the active species in plasma. Effects of gas flow rate, voltage, volume of solution, and processing time were also studied. Moreover, TEM and SEM images presented the mean diameter of nano-particle size around 10 to 20 nm. The results have been very promising.

  18. Treatment of Egyptian Maghara coal by plasma ozone synthesized by silent discharge

    CERN Document Server

    Salem, M A; Garamoon, A A; Hassouba, M A

    2003-01-01

    A sample of pyrite rich bituminous coal collected from the main coal seam of Maghara mine, northern sinai, was treated by ozone plasma. The latter was synthesized using silent discharge method (10 kv a.c. and 50 hz). The room temperature Moessbauer spectra of untreated coal sample was easily fitted to two doublet, whose parameters matched those of pyrite (FeS sub 2) and sulfate (FeSO sub 4.H sub 2 O) in addition to hematite. After treatment by ozone plasma, a doublet ascribed to pyrite was observed. The extent of pyrite oxidation to jarosite (Fe sub 2 (SO sub 4) sub 3. nH sub 2 O) was monitored by their relative spectral areas, the incomplete oxidation of pyrite may be attributed to the presence of calcium sulfate layer which acts a screen of ozone.

  19. Dielectric Barrier Discharge (DBD) Plasma Actuators Thrust-Measurement Methodology Incorporating New Anti-Thrust Hypothesis

    Science.gov (United States)

    Ashpis, David E.; Laun, Matthew C.

    2014-01-01

    We discuss thrust measurements of Dielectric Barrier Discharge (DBD) plasma actuators devices used for aerodynamic active flow control. After a review of our experience with conventional thrust measurement and significant non-repeatability of the results, we devised a suspended actuator test setup, and now present a methodology of thrust measurements with decreased uncertainty. The methodology consists of frequency scans at constant voltages. The procedure consists of increasing the frequency in a step-wise fashion from several Hz to the maximum frequency of several kHz, followed by frequency decrease back down to the start frequency of several Hz. This sequence is performed first at the highest voltage of interest, then repeated at lower voltages. The data in the descending frequency direction is more consistent and selected for reporting. Sample results show strong dependence of thrust on humidity which also affects the consistency and fluctuations of the measurements. We also observed negative values of thrust or "anti-thrust", at low frequencies between 4 Hz and up to 64 Hz. The anti-thrust is proportional to the mean-squared voltage and is frequency independent. Departures from the parabolic anti-thrust curve are correlated with appearance of visible plasma discharges. We propose the anti-thrust hypothesis. It states that the measured thrust is a sum of plasma thrust and anti-thrust, and assumes that the anti-thrust exists at all frequencies and voltages. The anti-thrust depends on actuator geometry and materials and on the test installation. It enables the separation of the plasma thrust from the measured total thrust. This approach enables more meaningful comparisons between actuators at different installations and laboratories. The dependence on test installation was validated by surrounding the actuator with a large diameter, grounded, metal sleeve.

  20. Role of turbulence fluctuations on uncertainties of acoutic Doppler current profiler discharge measurements

    Science.gov (United States)

    Tarrab, Leticia; Garcia, Carlos M.; Cantero, Mariano I.; Oberg, Kevin

    2012-01-01

    This work presents a systematic analysis quantifying the role of the presence of turbulence fluctuations on uncertainties (random errors) of acoustic Doppler current profiler (ADCP) discharge measurements from moving platforms. Data sets of three-dimensional flow velocities with high temporal and spatial resolution were generated from direct numerical simulation (DNS) of turbulent open channel flow. Dimensionless functions relating parameters quantifying the uncertainty in discharge measurements due to flow turbulence (relative variance and relative maximum random error) to sampling configuration were developed from the DNS simulations and then validated with field-scale discharge measurements. The validated functions were used to evaluate the role of the presence of flow turbulence fluctuations on uncertainties in ADCP discharge measurements. The results of this work indicate that random errors due to the flow turbulence are significant when: (a) a low number of transects is used for a discharge measurement, and (b) measurements are made in shallow rivers using high boat velocity (short time for the boat to cross a flow turbulence structure).

  1. Optimizing pulsed current micro plasma arc welding parameters to ...

    African Journals Online (AJOL)

    user

    tensile strength of pulsed current micro plasma arc welded Inconel 625 sheets. Four factors, five level, central composite rotatable design matrix is used to optimize the number of experiments. The mathematical model has been developed by using. Response Surface Method. The adequacy of the developed model is ...

  2. Effects and Mechanism of Atmospheric-Pressure Dielectric Barrier Discharge Cold Plasma on Lactate Dehydrogenase (LDH) Enzyme

    OpenAIRE

    Hao Zhang; Zimu Xu; Jie Shen; Xu Li; Lili Ding; Jie Ma; Yan Lan; Weidong Xia; Cheng Cheng; Qiang Sun; Zelong Zhang; Chu, Paul K

    2015-01-01

    Proteins are carriers of biological functions and the effects of atmospheric-pressure non-thermal plasmas on proteins are important to applications such as sterilization and plasma-induced apoptosis of cancer cells. Herein, we report our detailed investigation of the effects of helium-oxygen non-thermal dielectric barrier discharge (DBD) plasmas on the inactivation of lactate dehydrogenase (LDH) enzyme solutions. Circular dichroism (CD) and dynamic light scattering (DLS) indicate that the los...

  3. Study on Surface Damage and Performance Degradation of Impregnated Catalyst in Dielectric Barrier Discharge Plasma-Assisted Methane Conversion Processes.

    Science.gov (United States)

    Lee, Chung Jun; Lee, Dae Hoon; Kim, Taegyu

    2018-02-01

    This paper describes the performance degradation of impregnated catalyst in the dielectric barrier discharge (DBD) plasma-assisted methane conversion process. Mn and Ni mixed copper-zinc catalysts, and bare γ-Al2O3 support were exposed to the DBD plasma generated at 1 kHz and 9 kV under CH4 direct conversion for 4 hours. The performance degradation due to the surface damage of the catalyst by the plasma was investigated by SEM analysis.

  4. Formation of radical and active chemical species in electrical discharge plasma in the presence of liquid water

    Energy Technology Data Exchange (ETDEWEB)

    Locke, B.R.; Shih, K.Y.; Burlica, R. [Florida State Univ., Tallahassee, FL (United States). Dept. of Chemical and Biomedical Engineering

    2010-07-01

    This study investigated the interactions of plasma with liquid water using a combination of emission spectroscopy of radical and atomic species and direct measurements of more stable chemical compounds. The study focused on electrical discharge plasma formed directly in liquid water and on discharges formed in the gas phase above liquid water, in bubbles in liquid water, and in the gas phase with water droplet spray that result in a variety of active chemical species that can be used for pollution control as well as other applications in biomedical and materials engineering. The purpose was to improve the design and operation of plasma reactors for a variety of applications. This presentation also reviewed the mechanisms for the formation of active chemical species such as hydroxyl and other radicals, hydrogen peroxide and molecular hydrogen, in electrical discharge plasma formed in the presence of water.

  5. A novel large-scale plasma source: two discharge modes and their correlation to the production of aqueous reactive species

    Science.gov (United States)

    Wang, Bingchuan; Liu, Dingxin; Zhang, Zhiquan; Li, Qiaosong; Liu, Zhijie; Guo, Li; Wang, Xiaohua; Kong, Michael G.

    2017-08-01

    In this paper, a novel large-scale plasma source is put forward, which can generate two modes of discharge, i.e. the surface dielectric barrier discharge and the plasma jet array, by just varying the helium gas flow rate. It is found that the discharge power changes a little with the increasing gas flow rate, but the densities of reactive species in the gas phase and in the treated water change a lot. In particular, the gaseous O3 has its density decreasing while the aqueous O3 has its concentration increasing with the increasing gas flow rate. In the plasma-treated water, the reactive nitrogen species such as nitrite and nitrate have their concentrations first increasing and then decreasing, while the reactive oxygen species such as H2O2, O3 and OH have their concentrations increasing monotonically, implying that the plasma source is well-adaptive for different application requirements.

  6. Measurement of Plasma density in High Intensity Discharge Lamps by THz Interferometry

    Science.gov (United States)

    Kieckhafer, Alex; Curry, John

    2008-10-01

    A THz interferometer has been constructed with the goal of directly measuring plasma electron densities in High Intensity Discharge (HID) lamp plasmas. The use of THz frequencies has several advantages. Primary of these is the ability to measure high densities. The 0.6 THz system constructed is capable of measuring densities up to 4x10^15 cm-3. Additionally, the short wavelength of 0.6 THz radiation will allow focal spot sizes smaller than a millimeter in diameter, thus enabling high spatial resolution measurements. The system also differs from traditional microwave interferometry in that heterodyning has been eliminated. In inductively driven lamps the plasma recombines twice per AC cycle, when the voltage drops below a critical value. This time-dependent phase shift of the THz beam will allow calculation of density as a function of time. Zero-points can be acquired during the measurement itself due to the twice-per-cycle recombination of the plasma. Detection using electro-optical or nonlinear optical methods can easily achieve the time resolution required for these measurements, while maintaining sufficient signal-to-noise levels for detection without the assistance of lock-in amplification.

  7. Study of carbon dioxide gas treatment based on equations of kinetics in plasma discharge reactor

    Science.gov (United States)

    Abedi-Varaki, Mehdi

    2017-08-01

    Carbon dioxide (CO2) as the primary greenhouse gas, is the main pollutant that is warming earth. CO2 is widely emitted through the cars, planes, power plants and other human activities that involve the burning of fossil fuels (coal, natural gas and oil). Thus, there is a need to develop some method to reduce CO2 emission. To this end, this study investigates the behavior of CO2 in dielectric barrier discharge (DBD) plasma reactor. The behavior of different species and their reaction rates are studied using a zero-dimensional model based on equations of kinetics inside plasma reactor. The results show that the plasma reactor has an effective reduction on the CO2 density inside the reactor. As a result of reduction in the temporal variations of reaction rate, the speed of chemical reactions for CO2 decreases and very low concentration of CO2 molecules inside the plasma reactor is generated. The obtained results are compared with the existing experimental and simulation findings in the literature.

  8. Leading edge vortex control on a delta wing with dielectric barrier discharge plasma actuators

    Science.gov (United States)

    Shen, Lu; Wen, Chih-yung

    2017-06-01

    This paper presents an experimental investigation of the application of dielectric barrier discharge (DBD) plasma actuators on a slender delta wing to control the leading edge vortices (LEVs). The experiments are conducted in a wind tunnel with a Reynolds number of 50 000 based on the chord length. The smoke flow visualization reveals that the DBD plasma actuators at the leading edges significantly modify the vortical flow structure over the delta wing. It is noted that symmetric control at both semi-spans and asymmetric control at a single semi-span leads to opposite effects on the local LEVs. Particle image velocimetry (PIV) indicates that the shear layer is deformed by the actuators. Therefore, both the strength and the shape of the LEV cores are deeply affected. The six-component force measurement shows that the DBD plasma actuators have a limited effect on lift and drag while inducing relatively large moments. This suggests that the DBD plasma actuator is a promising technique for delta wing maneuvering.

  9. Plasma current start-up experiments without a central solenoid in the iron core STOR-M tokamak

    Science.gov (United States)

    Mitarai, O.; Tomney, G.; Rohollohi, A.; Lewis, E.; McColl, D.; Xiao, C.; Hirose, A.

    2015-06-01

    Reproducible plasma current start-up without a central solenoid (CS) has been demonstrated using the outer ohmic heating (OH) coils in the iron core STOR-M tokamak (Mitarai et al 2014 Fusion Eng. Des. 89 2467-71). Although the outer OH coil current saturates the iron core eventually, it has been demonstrated that the plasma current can be maintained during the iron core saturation phase. In this work, further studies have been conducted to investigate the effects of the turn number of the outer OH coils (N = 4 or N = 6) in the CS-less discharges and to evaluate the plasma stability with respect to the n-decay index of the vertical magnetic field. For the loose coupling of the iron core with N = 4 turns, the plasma current can be sustained after the additional third capacitor bank is applied near the iron core saturation phase, showing the slow transition from the unsaturated to the partially saturated phase. For the case of stronger coupling of N = 6 turns, the plasma current is increased at the same fast bank voltage, but the main discharge is shortened from 35 to 20 ms. As the magnetizing current is smaller due to stronger coupling between the OH coils and the plasma current, the transition from the unsaturated to the saturated phase is slightly difficult at present. The present experimental results suggest a feasible operation scenario in a future spherical tokamak (ST) at least using loose iron core coupling for smoother transition from the unsaturated to the saturated iron core phase. Thus, a reliable plasma current start-up by the outer OH coils and the current ramp-up to a steady state by additional heating power and vertical field coils could be considered as an operation scenario for future ST reactors with an iron core transformer.

  10. Oxygen functionalization of MWCNTs in RF-dielectric barrier discharge Ar/O2 plasma

    Science.gov (United States)

    Abdel-Fattah, E.; Ogawa, D.; Nakamura, K.

    2017-07-01

    The oxygenation of multi-wall carbon nanotubes (MWCNTs) was performed via a radio frequency dielectric barrier discharge (RF-DBD) in an Ar/{{\\text{H}}2}\\text{O} plasma mixture. The relative intensity of the Ar/{{\\text{O}}2} plasma species was characterized by optical emission spectroscopy (OES). The effects of treatment time, RF power and oxygen gas percentage on the chemical composition and surface morphology of MWCNTs were investigated by means of x-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy and field emission scanning electron microscopy (FE-SEM). The results of FTIR and XPS revealed the presence of oxygen-containing functional groups on the MWCNTs treated in an Ar/{{\\text{O}}2} plasma at an RF power of 50 W and pressure of 400 Pa. The amount of oxygen functional groups (C=O, C-O, and O-COO) also increased by increasing treatment time up to 6 min, but slightly decreased when treatment time was increased by 10 min. The increase of oxygen gas percentage in the plasma mixture does not affect the oxygen content in the treated MWCNTs. Meanwhile, MWCNTs treated at high power (80 W) showed a reduction in oxygen functional groups in comparison with low RF power conditions. The Raman analysis was consistent with the XPS and FTIR results. The integrity of the nanotube patterns also remained damaged as observed by FE-SEM images. The MWCNTs treated in RF-DBD using the Ar/{{\\text{O}}2} plasma mixture showed improved dispersibility in deionized water. A correlation between the OES data and the observed surface characterization for an improved understanding of the functionalization of MWCNTs in Ar/{{\\text{O}}2} plasma was presented.

  11. Time-resolved characteristics of deuteron-beam generated by plasma focus discharge

    Science.gov (United States)

    Bradley, D. A.

    2018-01-01

    The plasma focus device discussed herein is a Z-pinch pulsed-plasma arrangement. In this, the plasma is heated and compressed into a cylindrical column, producing a typical density of > 1025 particles/m3 and a temperature of (1–3) × 107 oC. The plasma focus has been widely investigated as a radiation source, including as ion-beams, electron-beams and as a source of x-ray and neutron production, providing considerable scope for use in a variety of technological situations. Thus said, the nature of the radiation emission depends on the dynamics of the plasma pinch. In this study of the characteristics of deuteron-beam emission, in terms of energy, fluence and angular distribution were analyzed. The 2.7 kJ plasma focus discharge has been made to operate at a pressure of less than 1 mbar rather than at its more conventional operating pressure of a few mbar. Faraday cup were used to determine deuteron-beam energy and deuteron-beam fluence per shot while CR-39 solid-state nuclear track detectors were employed in studying the angular distribution of deuteron emission. Beam energy and deuteron-beam fluence per shot have been found to be pressure dependent. The largest value of average deuteron energy measured for present conditions was found to be (52 ± 7) keV, while the deuteron-beam fluence per shot was of the order of 1015 ions/m2 when operated at a pressure of 0.2 mbar. The deuteron-beam emission is in the forward direction and is observed to be highly anisotropic. PMID:29309425

  12. Time-dependent simulation of plasma and electrodes in high-intensity discharge lamps with different electrode shapes

    CERN Document Server

    Flesch, P

    2003-01-01

    The subject of this paper is the modelling of d.c. and a.c. high-intensity Hg-discharge lamps with differently shaped electrodes. Different arc attachments on the electrodes are studied and insight for the development of new electrodes is gained. The model includes the entire discharge plasma (plasma column, hot plasma spots in front of electrodes, near-electrode non-LTE-plasma) as well as anode and cathode. No subdivision of the discharge space into different regions is necessary (like space charge layer, ionization zone, plasma column). This is achieved by using a differential equation for a non-LTE electrical conductivity which is applicable for local thermal equilibrium (LTE-)regions as well as for non-LTE plasma regions close to the electrodes in a high pressure plasma. Modelling results for a 0.6 MPa mercury discharge considering six different electrode shapes (anode and cathode) are presented and compared with experimental results. The electrodes have different diameters and different electrode tips, s...

  13. Plasma inactivation of microorganisms on sprout seeds in a dielectric barrier discharge.

    Science.gov (United States)

    Butscher, Denis; Van Loon, Hanne; Waskow, Alexandra; Rudolf von Rohr, Philipp; Schuppler, Markus

    2016-12-05

    Fresh produce is frequently contaminated by microorganisms, which may lead to spoilage or even pose a threat to human health. In particular sprouts are considered to be among the most risky foods sold at retail since they are grown in an environment practically ideal for growth of bacteria and usually consumed raw. Because heat treatment has a detrimental effect on the germination abilities of sprout seeds, alternative treatment technologies need to be developed for microbial inactivation purposes. In this study, non-thermal plasma decontamination of sprout seeds is evaluated as a promising option to enhance food safety while maintaining the seed germination capabilities. In detail, investigations focus on understanding the efficiency of non-thermal plasma inactivation of microorganisms as influenced by the type of microbial contamination, substrate surface properties and moisture content, as well as variations in the power input to the plasma device. To evaluate the impact of these parameters, we studied the reduction of native microbiota or artificially applied E. coli on alfalfa, onion, radish and cress seeds exposed to non-thermal plasma in an atmospheric pressure pulsed dielectric barrier discharge streamed with argon. Plasma treatment resulted in a maximum reduction of 3.4 logarithmic units for E. coli on cress seeds. A major challenge in plasma decontamination of granular food products turned out to be the complex surface topology, where the rough surface with cracks and crevices can shield microorganisms from plasma-generated reactive species, thus reducing the treatment efficiency. However, improvement of the inactivation efficiency was possible by optimizing substrate characteristics such as the moisture level and by tuning the power supply settings (voltage, frequency) to increase the production of reactive species. While the germination ability of alfalfa seeds was considerably decreased by harsh plasma treatment, enhanced germination was observed under

  14. Dielectric Barrier Discharge based Mercury-free plasma UV-lamp for efficient water disinfection.

    Science.gov (United States)

    Prakash, Ram; Hossain, Afaque M; Pal, U N; Kumar, N; Khairnar, K; Mohan, M Krishna

    2017-12-12

    A structurally simple dielectric barrier discharge based mercury-free plasma UV-light source has been developed for efficient water disinfection. The source comprises of a dielectric barrier discharge arrangement between two co-axial quartz tubes with an optimized gas gap. The outer electrode is an aluminium baked foil tape arranged in a helical form with optimized pitch, while the inner electrode is a hollow aluminium metallic rod, hermetically sealed. Strong bands peaking at wavelengths 172 nm and 253 nm, along with a weak band peaking at wavelength 265 nm have been simultaneously observed due to plasma radiation from the admixture of xenon and iodine gases. The developed UV source has been used for bacterial deactivation studies using an experimental setup that is an equivalent of the conventional house-hold water purifier system. Deactivation studies for five types of bacteria, i.e., E. coli, Shigella boydii, Vibrio, Coliforms and Fecal coliform have been demonstrated with 4 log reductions in less than ten seconds.

  15. An advanced time-dependent collisional-radiative model of helium plasma discharges

    Science.gov (United States)

    Claustre, J.; Boukandou-Mombo, C.; Margot, J.; Matte, J.-P.; Vidal, F.

    2017-10-01

    A new spatially averaged time-dependent collisional-radiative model for helium plasmas, coupled to the electron Boltzmann equation (EBE), has been developed. Its main novelties are: (1) full time dependence for both the multi-species kinetics and the EBE. It is shown that this is necessary to correctly simulate discharges where the parameters vary on nanoseconds-microsecond timescales. (2) All electron processes are accounted for accurately. In particular, for the various ionization and recombination processes, free electrons are added or removed at the appropriate energy, with the appropriate interpolation on the energy grid. (3) The energy dependence of the electron loss by ambipolar diffusion is taken into account approximately. (4) All of the processes which are known to be important in helium discharges for pressure P≤slant 760 Torr are included, and 42 energy levels up to n = 6, where n is the main quantum number, are taken into account. Atomic and molecular ions, as well as excimers, are also included. (5) The gas temperature is calculated self-consistently. The model is validated through comparisons with known numerical steady-state results of Santos et al (2014 J. Phys. D. 47 265201) which they compared to their experimental results, and good agreement is obtained for their measured quantities. It is then applied to post-discharge decay cases with very short power decay times. The time evolution of the population densities and reaction rates are analyzed in detail with emphasis on the observed large increase of the metastable density.

  16. [Quality of hospital discharge reports in terms of current legislation and expert recommendations].

    Science.gov (United States)

    Zambrana-García, José Luis; Rivas-Ruiz, Francisco

    2013-01-01

    To determine the quality of hospital discharge reports (HDRs) taking into account current legislation and the conclusions of the consensus on hospital discharge reports in medical specialities in 11 community hospitals in Andalusia (Spain). A cross-sectional study of 1,708 HDRs was carried out. We determined the presence or absence of the various items required by current legislation and by the recommendations of the above-mentioned consensus. A total of 97.4% (95% confidence interval [95% CI]: 96.5-98.2) of the HDRs were classified as satisfactory according to the stipulations of current legislation. However, when the assessment was based on the consensus, the rate of adequacy fell to 72.1% (95% CI: 70.0-74.3). A notable finding was the absence of the duration of treatment after hospital discharge in 39.4% of the HDRs. HDRs show an excellent level of compliance with the data required by current regulations, but their intrinsic quality needs to be improved. Copyright © 2012 SESPAS. Published by Elsevier Espana. All rights reserved.

  17. Current leakage for low altitude satellites. [to surrounding plasma sheath

    Science.gov (United States)

    Mccoy, J. E.; Konradi, A.; Garriott, O. K.

    1979-01-01

    Ionospheric plasma densities exceeding 1,000,000 per cu cm exist around satellites in low earth orbit. Operation of large solar arrays at high voltage may drive substantial leakage currents through this surrounding plasma. Power losses exceeding solar cell output have been observed for small arrays biased above +2,000 V. Estimates of these effects for very large power systems are developed. Recent large scale (10 meter) lab tests are reported. Estimates based on calculations of space charge limited sheath dimensions are identified as a good working model, leading to projected power losses for large arrays increasing much more slowly than for small arrays.

  18. Thermal regime of self-heated hollow cathode in a low-pressure high-current pulsed-periodic discharge

    Science.gov (United States)

    Gavrilov, N. V.; Emlin, D. R.

    2017-11-01

    We have studied the thermal regime of a self-heated hollow cathode in combined low-current (1-5 A) dc discharge and high-current (up to 100 A) pulsed-periodic discharge and the influence of the pulsed parameters on the current-voltage characteristic of the high-current discharge. It has been shown that, after the application of a voltage pulse (200-500 V), the discharge current attains its peak value and is stabilized over a time of 100 μs. The discharge voltage in the quasi-stationary discharge stage exceeds the continuous discharge voltage at the same current by many times and depends on the mean value of the current in the discharge gap. The interpretation of the form of the I-V characteristics of the pulsed discharge is based on the dynamics of heating and cooling of the cathode surface layer and on the variations in the integral temperature of the cathode.

  19. Modeling of inductively coupled plasma SF{sub 6}/O{sub 2}/Ar plasma discharge: Effect of O{sub 2} on the plasma kinetic properties

    Energy Technology Data Exchange (ETDEWEB)

    Pateau, Amand [Institut des Matériaux Jean Rouxel, Université de Nantes, 2 rue de la Houssiniére 44322 Nantes, France and ST Microelectronics, 10 rue Thals de Milet, 37071 Tours (France); Rhallabi, Ahmed, E-mail: ahmed.rhallabi@univ-nantes.fr; Fernandez, Marie-Claude [Institut des Matériaux Jean Rouxel, Université de Nantes, 2 rue de la Houssiniére 44322 Nantes (France); Boufnichel, Mohamed; Roqueta, Fabrice [ST Microelectronics, 10 rue Thales de Milet, 37071 Tours (France)

    2014-03-15

    A global model has been developed for low-pressure, inductively coupled plasma (ICP) SF{sub 6}/O{sub 2}/Ar mixtures. This model is based on a set of mass balance equations for all the considered species, coupled with the discharge power balance equation and the charge neutrality condition. The present study is an extension of the kinetic global model previously developed for SF{sub 6}/Ar ICP plasma discharges [Lallement et al., Plasma Sources Sci. Technol. 18, 025001 (2009)]. It is focused on the study of the impact of the O{sub 2} addition to the SF{sub 6}/Ar gas mixture on the plasma kinetic properties. The simulation results show that the electron density increases with the %O{sub 2}, which is due to the decrease of the plasma electronegativity, while the electron temperature is almost constant in our pressure range. The density evolutions of atomic fluorine and oxygen versus %O{sub 2} have been analyzed. Those atomic radicals play an important role in the silicon etching process. The atomic fluorine density increases from 0 up to 40% O{sub 2} where it reaches a maximum. This is due to the enhancement of the SF{sub 6} dissociation processes and the production of fluorine through the reactions between SF{sub x} and O. This trend is experimentally confirmed. On the other hand, the simulation results show that O(3p) is the preponderant atomic oxygen. Its density increases with %O{sub 2} until reaching a maximum at almost 40% O{sub 2}. Over this value, its diminution with O{sub 2}% can be justified by the high increase in the loss frequency of O(3p) by electronic impact in comparison to its production frequency by electronic impact with O{sub 2}.

  20. Particle modelling of magnetically confined oxygen plasma in low pressure radio frequency discharge

    Energy Technology Data Exchange (ETDEWEB)

    Benyoucef, Djilali [Laboratoire Génie Electrique et Energie Renouvelables, Chlef University (Algeria); Yousfi, Mohammed [Université de de Toulouse, LAPLACE, UMR CNRS 5213, 118 Route de Narbonne, Toulouse 31062 (France)

    2015-01-15

    The main objective of this paper is the modelling and simulation of a radio frequency (RF) discharge in oxygen at low pressure and at room temperature, including the effect of crossed electric and magnetic fields for generation and confinement of oxygen plasma. The particle model takes into account one axial dimension along the electric field axis and three velocity components during the Monte Carlo treatment of the collisions between charged particles and background gas. The simulation by this developed code allows us not only to determine the electrodynamics characteristics of the RF discharge, but also to obtain kinetics and energetic description of reactive oxygen plasma at low pressure. These information are very important for the control of the deep reactive-ion etching technology of the silicon to manufacture capacitors with high density and for the deposition thick insulating films or thick metal to manufacture micro-coils. The simulation conditions are as follows: RF peak voltage of 200 V, frequency of 13.56 MHz, crossed magnetic field varying from 0 to 50 Gauss, and oxygen pressure of 13.8 Pa. In the presence of magnetic field, the results show an increase of the plasma density, a decrease of the electron mean energy, and also a reduction of the ratio between electron density and positive ion density. Finally in order to validate, the results are successfully compared with measurements already carried out in the literature. The conditions of comparison are from 100 to 300 V of the peak voltage at 13.56 MHz under a pressure of 13.8 Pa and a gap distance of 2.5 cm.

  1. Current flow instability and nonlinear structures in dissipative two-fluid plasmas

    Science.gov (United States)

    Koshkarov, O.; Smolyakov, A. I.; Romadanov, I. V.; Chapurin, O.; Umansky, M. V.; Raitses, Y.; Kaganovich, I. D.

    2018-01-01

    The current flow in two-fluid plasma is inherently unstable if plasma components (e.g., electrons and ions) are in different collisionality regimes. A typical example is a partially magnetized E ×B plasma discharge supported by the energy released from the dissipation of the current in the direction of the applied electric field (perpendicular to the magnetic field). Ions are not magnetized so they respond to the fluctuations of the electric field ballistically on the inertial time scale. In contrast, the electron current in the direction of the applied electric field is dissipatively supported either by classical collisions or anomalous processes. The instability occurs due to a positive feedback between the electron and ion current coupled by the quasi-neutrality condition. The theory of this instability is further developed taking into account the electron inertia, finite Larmor radius and nonlinear effects. It is shown that this instability results in highly nonlinear quasi-coherent structures resembling breathing mode oscillations in Hall thrusters.

  2. Current and Perspective Applications of Dense Plasma Focus Devices

    Science.gov (United States)

    Gribkov, V. A.

    2008-04-01

    Dense Plasma Focus (DPF) devices' applications, which are intended to support the main-stream large-scale nuclear fusion programs (NFP) from one side (both in fundamental problems of Dense Magnetized Plasma physics and in its engineering issues) as well as elaborated for an immediate use in a number of fields from the other one, are described. In the first direction such problems as self-generated magnetic fields, implosion stability of plasma shells having a high aspect ratio, etc. are important for the Inertial Confinement Fusion (ICF) programs (e.g. as NIF), whereas different problems of current disruption phenomenon, plasma turbulence, mechanisms of generation of fast particles and neutrons in magnetized plasmas are of great interest for the large devices of the Magnetic Plasma Confinement—MPC (e.g. as ITER). In a sphere of the engineering problems of NFP it is shown that in particular the radiation material sciences have DPF as a very efficient tool for radiation tests of prospect materials and for improvement of their characteristics. In the field of broad-band current applications some results obtained in the fields of radiation material sciences, radiobiology, nuclear medicine, express Neutron Activation Analysis (including a single-shot interrogation of hidden illegal objects), dynamic non-destructive quality control, X-Ray microlithography and micromachining, and micro-radiography are presented. As the examples of the potential future applications it is proposed to use DPF as a powerful high-flux neutron source to generate very powerful pulses of neutrons in the nanosecond (ns) range of its duration for innovative experiments in nuclear physics, for the goals of radiation treatment of malignant tumors, for neutron tests of materials of the first wall, blankets and NFP device's constructions (with fluences up to 1 dpa per a year term), and ns pulses of fast electrons, neutrons and hard X-Rays for brachytherapy.

  3. Relation between magnetic fields and electric currents in plasmas

    Directory of Open Access Journals (Sweden)

    V. M. Vasyliunas

    2005-10-01

    Full Text Available Maxwell's equations allow the magnetic field B to be calculated if the electric current density J is assumed to be completely known as a function of space and time. The charged particles that constitute the current, however, are subject to Newton's laws as well, and J can be changed by forces acting on charged particles. Particularly in plasmas, where the concentration of charged particles is high, the effect of the electromagnetic field calculated from a given J on J itself cannot be ignored. Whereas in ordinary laboratory physics one is accustomed to take J as primary and B as derived from J, it is often asserted that in plasmas B should be viewed as primary and J as derived from B simply as (c/4π∇×B. Here I investigate the relation between ∇×B and J in the same terms and by the same method as previously applied to the MHD relation between the electric field and the plasma bulk flow vmv2001: assume that one but not the other is present initially, and calculate what happens. The result is that, for configurations with spatial scales much larger than the electron inertial length λe, a given ∇×B produces the corresponding J, while a given J does not produce any ∇×B but disappears instead. The reason for this can be understood by noting that ∇×B≠4π/cJ implies a time-varying electric field (displacement current which acts to change both terms (in order to bring them toward equality; the changes in the two terms, however, proceed on different time scales, light travel time for B and electron plasma period for J, and clearly the term changing much more slowly is the one that survives. (By definition, the two time scales are equal at λe. On larger scales, the evolution of B (and hence also of ∇×B is governed by ∇×E, with E determined by plasma dynamics via the generalized Ohm's law; as illustrative simple examples, I discuss the formation of magnetic drift currents in the magnetosphere and of Pedersen and Hall currents in

  4. Plasma-Surface Interactions in Hollow Cathode Discharges for Electric Propulsion

    Science.gov (United States)

    Capece, Angela Maria

    Electric thrusters generate high exhaust velocities and can achieve specific impulses in excess of 1000 s. The low thrust generation and high specific impulse make electric propulsion ideal for interplanetary missions, spacecraft station keeping, and orbit raising maneuvers. Consequently, these devices have been used on a variety of space missions including Deep Space 1, Dawn, and hundreds of commercial spacecraft in Earth orbit. In order to provide the required total impulses, thruster burn time can often exceed 10,000 hours, making thruster lifetime essential. One of the main life-limiting components on ion engines is the hollow cathode, which serves as the electron source for ionization of the xenon propellant gas. Reactive contaminants such as oxygen can modify the cathode surface morphology and degrade the electron emission properties. Hollow cathodes that operate with reactive impurities in the propellant will experience higher operating temperatures, which increase evaporation of the emission materials and reduce cathode life. A deeper understanding of the mechanisms initiating cathode failure will improve thruster operation, increase lifetime, and ultimately reduce cost. A significant amount of work has been done previously to understand the effects of oxygen poisoning on vacuum cathodes; however, the xenon plasma adds complexity, and its role during cathode poisoning is not completely understood. The work presented here represents the first attempt at understanding how oxygen impurities in the xenon discharge plasma alter the emitter surface and affect operation of a 4:1:1 BaO-CaO-Al2O3 hollow cathode. A combination of experimentation and modeling was used to investigate how oxygen impurities in the discharge plasma alter the emitter surface and reduce the electron emission capability. The experimental effort involved operating a 4:1:1 hollow cathode at various conditions with oxygen impurities in the xenon flow. Since direct measurements of the emitter

  5. Research in Water Permeability of Poly(ethylene) Terephthalate Track Membranes Modified by Polymerization of Dimethylaniline under the Action of Direct Current Discharge

    CERN Document Server

    Kravets, L I; Drachev, A I

    2004-01-01

    The properties of poly(ethylene) terephthalate track membranes modified by polymerization of dimethylaniline in a discharge of direct current are investigated. The influence of conditions of plasma treatment on the basic characteristics of the membranes (pore size, wettability, surface charge, water permeability) is studied. It is shown that under the action of discharge, a polymeric layer is formed on the membrane surface that can swell in solutions with low pH values. It has been found that the degree of the swelling stipulated by the conformation transfer of macromolecules of the deposited polymeric layer depends upon the size of relative magnification of the mass of the membrane during its plasma treatment. It is also shown that the obtained membranes can reversibly react to changing the pH of solution and applied pressure.

  6. Mercury-free electrodeless discharge lamp: effect of xenon pressure and plasma parameters on luminance

    Science.gov (United States)

    Ahmad, Nazri Dagang; Kondo, Akira; Motomura, Hideki; Jinno, Masafumi

    2009-05-01

    Since there is much concern about environmental preservation, the authors have paid attention to the uses of mercury in lighting application. They have focused on the application of the xenon low-pressure inductively coupled plasma (ICP) discharge in developing cylindrical type mercury-free light sources. ICP can be operated at low filling gas pressures and demonstrates significant potential in producing high density plasma. Xenon pressure was varied from 0.1 to 100 Torr and the lamp luminance was measured. The gas pressure dependence shows an increase in luminance at pressures below 1 Torr. In order to clarify this behaviour, measurement of plasma parameters was carried out using the double probe method and its relation to lamp luminance is discussed. As the gas pressure is decreased (from 1 to 0.01 Torr), the electron temperature increases while the electron density decreases while at the same time the lamp luminance increases. There are several factors that are believed to contribute to the increase in luminance in the very low pressure region. Increases in luminance are considered to be due to the electron-ion recombination process which brings a strong recombination radiation in continuum in the visible region and also due to the effect of stochastic heating.

  7. Spatial distributions of plasma parameters in inductively coupled hydrogen discharges with an expansion region

    Science.gov (United States)

    Gao, Fei; Zhang, Yu-Ru; Li, Hong; Liu, Yang; Wang, You-Nian

    2017-07-01

    Spatial distributions of plasma parameters have been investigated by a Langmuir probe in a hydrogen inductively coupled plasma with an expansion region. The influence of the gas pressure and the radio-frequency power on the electron energy probability function (EEPF), electron density, and electron temperature has been presented. The results indicate that the EEPF evolves from a bi-Maxwellian distribution in the discharge driver region to a Maxwellian distribution in the expansion region at low pressures, whereas it is always characterized by a Maxwellian distribution at high pressures. Moreover, the electron density exhibits a bell-shaped profile in the driver region, while the electron temperature shows a relatively uniform distribution there, and they decrease to low values in the expansion region. In order to verify the experimental results, we use the COMSOL simulation software to calculate the electron density and electron temperature at different powers at 2 Pa. The simulated and measured axial distributions of the plasma properties agree well except for the absolute value, i.e., the calculated electron temperature is higher at all the RF powers, and the calculated electron density is underestimated at 2 kW, while a better agreement is obtained at low RF power.

  8. Control of stationary crossflow modes in swept Hiemenz flows with dielectric barrier discharge plasma actuators

    Science.gov (United States)

    Wang, Zhefu; Wang, Liang; Fu, Song

    2017-09-01

    Sensitivity analyses and non-linear parabolized stability equations are solved to provide a computational assessment of the potential use of a Dielectric Barrier Discharge (DBD) plasma actuator for a prolonging laminar region in swept Hiemenz flow. The derivative of the kinetic energy with respect to the body force is deduced, and its components in different directions are defined as sensitivity functions. The results of sensitivity analyses and non-linear parabolized stability equations both indicate that the introduction of a body force as the plasma actuator at the bottom of a crossflow vortex can mitigate instability to delay flow transition. In addition, the actuator is more effective when placed more upstream until the neutral point. In fact, if the actuator is sufficiently close to the neutral point, it is likely to act as a strong disturbance over-riding the natural disturbance and dominating transition. Different operating voltages of the DBD actuators are tested, resulting in an optimal practice for transition delay. The results demonstrate that plasma actuators offer great potential for transition control.

  9. Capabilities of the dielectric barrier discharge plasma actuator for multi-frequency excitations

    Energy Technology Data Exchange (ETDEWEB)

    Benard, N; Moreau, E [Laboratoire d' Etudes Aerodynamiques (LEA), Universite de Poitiers, ENSMA, CNRS Bld Marie et Pierre Curie, Teleport 2, 86962 Futuroscope Cedex (France)

    2010-04-14

    Natural instability mechanisms are inherent in most laminar and turbulent flow configurations. Usually, these instabilities result in the formation of flow structures occurring at diverse spatial and time scales. An effective control requires an actuator able to bring momentum transfer over a wide range of frequencies to act on these instabilities. Promising results are expected for such control strategy because, according to stability theory, a small amplitude perturbation can be large enough to produce significant effects even at high Reynolds number. Moreover, simultaneous production of small perturbations at several frequencies can enhance or cancel non-linear interactions; this opens alternative methods for flow control. The focus of this study is to demonstrate the ability of plasma actuators to introduce flow perturbations at single and dual frequencies by simply adjusting the waveform of the voltage applied to the plasma actuator. The flows produced by a dielectric barrier discharge supplied by burst, superposition and ring modulations are described in temporal and frequential domains. The results confirm the potential of non-thermal plasma actuators to produce highly unsteady flows at single, double or multiple frequencies.

  10. Mercury-free electrodeless discharge lamp: effect of xenon pressure and plasma parameters on luminance

    Energy Technology Data Exchange (ETDEWEB)

    Nazri Dagang Ahmad; Kondo, Akira; Motomura, Hideki; Jinno, Masafumi, E-mail: nazri@mayu.ee.ehime-u.ac.j [Department of Electrical and Electronic Engineering, 3 Bunkyo-cho, Matsuyama, Ehime 790-8577 (Japan)

    2009-05-07

    Since there is much concern about environmental preservation, the authors have paid attention to the uses of mercury in lighting application. They have focused on the application of the xenon low-pressure inductively coupled plasma (ICP) discharge in developing cylindrical type mercury-free light sources. ICP can be operated at low filling gas pressures and demonstrates significant potential in producing high density plasma. Xenon pressure was varied from 0.1 to 100 Torr and the lamp luminance was measured. The gas pressure dependence shows an increase in luminance at pressures below 1 Torr. In order to clarify this behaviour, measurement of plasma parameters was carried out using the double probe method and its relation to lamp luminance is discussed. As the gas pressure is decreased (from 1 to 0.01 Torr), the electron temperature increases while the electron density decreases while at the same time the lamp luminance increases. There are several factors that are believed to contribute to the increase in luminance in the very low pressure region. Increases in luminance are considered to be due to the electron-ion recombination process which brings a strong recombination radiation in continuum in the visible region and also due to the effect of stochastic heating.

  11. Evidence of current free double layer in high density helicon discharge

    Energy Technology Data Exchange (ETDEWEB)

    Ganguli, A. [Centre for Energy Studies, Indian Institute of Technology, New Delhi 110016 (India); Sahu, B. B. [Department of Applied Sciences and Humanities, Dronacharya College of Engineering, Gurgaon 123506 (India); Tarey, R. D. [Department of Physics, Indian Institute of Technology, New Delhi 110016 (India)

    2013-01-15

    This paper investigates the formation of double layer (DL) in helicon plasmas. In the experiment, argon plasma production is using the excitation of m = -1 helicon mode with magnetic mirror field with high mirror ratio of {approx}1:1.7. We have specifically used the radio frequency compensated Langmuir probe (LP) to measure the relevant plasma parameters simultaneously so as to investigate the details about the plasma production. The DL, which consists of both warm and bulk populations towards higher potential region and only dense bulk plasmas towards the lower potential region downstream the antenna, is present in the transition region. LP measurements also show an abrupt fall of density along with a potential drop of about 20 V and (e {Delta}V{sub p}/k T{sub e}) Almost-Equal-To 12 within a few cm. The potential drop is equal to the difference of the electron temperatures between the two plasma regions forming the DL, which is present in the plateau region of mirror, unlike in several prior studies on the DL formation in the region of strong gradients in the magnetic field. The DL is strong, current-free, electric double-layer with estimated thickness of about 10 Debye lengths.

  12. Plasma sources for high-current electron beam generation

    Science.gov (United States)

    Krasik, Ya. E.; Dunaevsky, A.; Felsteiner, J.

    2001-05-01

    A review of experimental studies of the operation of cathodes made of metal-ceramic, velvet, corduroy, carbon fibers, carbon fabric, and different types of ferroelectrics is presented. These cathodes operated at electric fields in the range of 5-60 kV/cm that allowed the generation of electron beams with duration of several hundreds of nanoseconds while keeping a quasi-constant diode impedance. All cathodes had the same diameter and were tested in a diode powered by a high-voltage generator (300 kV, 85 Ω, 250 ns, ⩽5 Hz). It was shown that the source of electrons for all the studied cathodes is a plasma which is formed as a result of surface discharges. Different types of electrical and optical diagnostics were used to study the formation and parameters of the plasma, the potential distribution inside the anode-cathode gap, and the uniformity and divergence of the extracted electron beam as a function of the amplitude and rise time of the accelerating pulse. Results of the lifetime of the tested cathodes and their compatibility with vacuum requirements are presented as well.

  13. Dissipated power and induced velocity fields data of a micro single dielectric barrier discharge plasma actuator for active flow control

    Directory of Open Access Journals (Sweden)

    E. Pescini

    2015-12-01

    Full Text Available In recent years, single dielectric barrier discharge (SDBD plasma actuators have gained great interest among all the active flow control devices typically employed in aerospace and turbomachinery applications [1,2]. Compared with the macro SDBDs, the micro single dielectric barrier discharge (MSDBD actuators showed a higher efficiency in conversion of input electrical power to delivered mechanical power [3,4]. This article provides data regarding the performances of a MSDBD plasma actuator [5,6]. The power dissipation values [5] and the experimental and numerical induced velocity fields [6] are provided. The present data support and enrich the research article entitled “Optimization of micro single dielectric barrier discharge plasma actuator models based on experimental velocity and body force fields” by Pescini et al. [6].

  14. Dissipated power and induced velocity fields data of a micro single dielectric barrier discharge plasma actuator for active flow control.

    Science.gov (United States)

    Pescini, E; Martínez, D S; De Giorgi, M G; Francioso, L; Ficarella, A

    2015-12-01

    In recent years, single dielectric barrier discharge (SDBD) plasma actuators have gained great interest among all the active flow control devices typically employed in aerospace and turbomachinery applications [1,2]. Compared with the macro SDBDs, the micro single dielectric barrier discharge (MSDBD) actuators showed a higher efficiency in conversion of input electrical power to delivered mechanical power [3,4]. This article provides data regarding the performances of a MSDBD plasma actuator [5,6]. The power dissipation values [5] and the experimental and numerical induced velocity fields [6] are provided. The present data support and enrich the research article entitled "Optimization of micro single dielectric barrier discharge plasma actuator models based on experimental velocity and body force fields" by Pescini et al. [6].

  15. Time development of electric fields and currents in space plasmas

    Directory of Open Access Journals (Sweden)

    A. T. Y. Lui

    2006-05-01

    Full Text Available Two different approaches, referred to as Bu and Ej, can be used to examine the time development of electric fields and currents in space plasmas based on the fundamental laws of physics. From the Bu approach, the required equation involves the generalized Ohm's law with some simplifying assumptions. From the Ej approach, the required equation can be derived from the equation of particle motion, coupled self-consistently with Maxwell's equation, and the definition of electric current density. Recently, some strong statements against the Ej approach have been made. In this paper, we evaluate these statements by discussing (1 some limitations of the Bu approach in solving the time development of electric fields and currents, (2 the procedure in calculating self-consistently the time development of the electric current in space plasmas without taking the curl of the magnetic field in some cases, and (3 the dependency of the time development of magnetic field on electric current. It is concluded that the Ej approach can be useful to understand some magnetospheric problems. In particular, statements about the change of electric current are valid theoretical explanations of change in magnetic field during substorms.

  16. Time development of electric fields and currents in space plasmas

    Directory of Open Access Journals (Sweden)

    A. T. Y. Lui

    2006-05-01

    Full Text Available Two different approaches, referred to as Bu and Ej, can be used to examine the time development of electric fields and currents in space plasmas based on the fundamental laws of physics. From the Bu approach, the required equation involves the generalized Ohm's law with some simplifying assumptions. From the Ej approach, the required equation can be derived from the equation of particle motion, coupled self-consistently with Maxwell's equation, and the definition of electric current density. Recently, some strong statements against the Ej approach have been made. In this paper, we evaluate these statements by discussing (1 some limitations of the Bu approach in solving the time development of electric fields and currents, (2 the procedure in calculating self-consistently the time development of the electric current in space plasmas without taking the curl of the magnetic field in some cases, and (3 the dependency of the time development of magnetic field on electric current. It is concluded that the Ej approach can be useful to understand some magnetospheric problems. In particular, statements about the change of electric current are valid theoretical explanations of change in magnetic field during substorms.

  17. Systematic Comparison between Half and Full Dielectric Barrier Discharges Based on the Low Temperature Plasma Probe (LTP) and Dielectric Barrier Discharge for Soft Ionization (DBDI) Configurations.

    Science.gov (United States)

    Klute, Felix D; Brandt, Sebastian; Vogel, Pascal; Biskup, Beatrix; Reininger, Charlotte; Horvatic, Vlasta; Vadla, Cedomil; Farnsworth, Paul B; Franzke, Joachim

    2017-09-05

    Dielectric barrier discharge (DBD)-based analytical applications have experienced rapid development in recent years. DBD designs and parameters and the application they are used for can vary considerably. This leads to a diverse field with many apparently unique systems that are all based on the same physical principle. The most significant changes among DBDs used for chemical analysis are in how the discharge electrodes are separated from the ignited discharge gas. While the official definition of a DBD states that at least one electrode has to be covered by a dielectric to be considered a DBD, configurations with both electrodes covered by dielectric layers can also be realized. The electrode surface plays a major role in several plasma-related technical fields, surface treatment or sputtering processes, for example, and has hence been studied in great detail. Analytical DBDs are often operated at low power and atmospheric pressure, making a direct transfer of insight and know-how gained from the aforementioned well-studied fields complicated. This work focuses on comparing two DBD configurations: the low temperature plasma probe (LTP) and the dielectric barrier discharge for soft ionization (DBDI). The LTP is representative of a DBD with one covered electrode and the DBDI of a design in which both electrodes are covered. These two configurations are well suited for a systematic comparison due to their similar geometric designs based on a dielectric capillary.

  18. Measuring discharge with acoustic Doppler current profilers from a moving boat

    Science.gov (United States)

    Mueller, David S.; Wagner, Chad R.; Rehmel, Michael S.; Oberg, Kevin A.; Rainville, Francois

    2013-01-01

    The use of acoustic Doppler current profilers (ADCPs) from a moving boat is now a commonly used method for measuring streamflow. The technology and methods for making ADCP-based discharge measurements are different from the technology and methods used to make traditional discharge measurements with mechanical meters. Although the ADCP is a valuable tool for measuring streamflow, it is only accurate when used with appropriate techniques. This report presents guidance on the use of ADCPs for measuring streamflow; this guidance is based on the experience of U.S. Geological Survey employees and published reports, papers, and memorandums of the U.S. Geological Survey. The guidance is presented in a logical progression, from predeployment planning, to field data collection, and finally to post processing of the collected data. Acoustic Doppler technology and the instruments currently (2013) available also are discussed to highlight the advantages and limitations of the technology. More in-depth, technical explanations of how an ADCP measures streamflow and what to do when measuring in moving-bed conditions are presented in the appendixes. ADCP users need to know the proper procedures for measuring discharge from a moving boat and why those procedures are required, so that when the user encounters unusual field conditions, the procedures can be adapted without sacrificing the accuracy of the streamflow-measurement data.

  19. Action-potential discharge in hippocampal CA1 pyramidal neurons: current source-density analysis.

    Science.gov (United States)

    Richardson, T L; Turner, R W; Miller, J J

    1987-11-01

    1. The site of origin of evoked action-potential discharge in hippocampal CA1 pyramidal neurons was investigated using the in vitro rat hippocampal slice preparation. 2. Action-potential discharge in pyramidal cells was evoked by stimulation of efferent pyramidal cell fibers in the alveus (antidromic) or afferent synaptic inputs in stratum oriens (SO) or stratum radiatum (SR). Laminar profiles of evoked extracellular field potentials were recorded at 25-micron intervals along the entire dendrosomatic axis of the pyramidal cell and a one-dimensional current source-density analysis was applied. 3. Suprathreshold stimulation of the alveus evoked an antidromic population spike response and current sink with the shortest peak latency in stratum pyramidale or proximal stratum oriens. A biphasic positive/negative potential associated with a current source/sink was recorded in dendritic regions, with both components increasing in peak latency with distance from the border of stratum pyramidale. 4. Suprathreshold stimulation of SO or SR evoked a population spike response superimposed upon the underlying synaptic depolarization at all levels of the dendrosomatic axis. The shortest latency population spike and current sink were recorded in stratum pyramidale or proximal stratum oriens. In dendritic regions, a biphasic positive/negative potential and current source/sink conducted with increasing latency from the border of stratum pyramidale. 5. A direct comparison of alvear- and SR-evoked responses revealed a basic similarity in population spike potentials and associated sink/source relationships at both the somatic and dendritic level and a similar shift in peak latency of spike components along the pyramidal cell axis. 6. It is concluded that the initial site for generation of a spike along the dendrosomatic axis of the pyramidal cell following antidromic or orthodromic stimulation is in the region of the cell body layer (soma or axon hillock). Action-potential discharge in

  20. Use of an Acoustic Doppler Current Profiler (ADCP) to Measure Hypersaline Bidirectional Discharge

    Science.gov (United States)

    Johnson, K.K.; Loving, B.L.; ,

    2002-01-01

    The U.S. Geological Survey measures the exchange of flow between the north and south parts of Great Salt Lake, Utah, as part of a monitoring program. Turbidity and bidirectional flow through the breach in the causeway that divides the lake into two parts makes it difficult to measure discharge with conventional streamflow techniques. An acoustic Doppler current profiler (ADCP) can be used to more accurately define the angles of flow and the location of the interface between the layers of flow. Because of the high salinity levels measured in Great Salt Lake (60-280 parts per thousand), special methods had to be developed to adjust ADCP-computed discharges for the increased speed of sound in hypersaline waters and for water entrained at the interface between flow layers.

  1. A comparative study for the inactivation of multidrug resistance bacteria using dielectric barrier discharge and nano-second pulsed plasma.

    Science.gov (United States)

    Park, Ji Hoon; Kumar, Naresh; Park, Dae Hoon; Yusupov, Maksudbek; Neyts, Erik C; Verlackt, Christof C W; Bogaerts, Annemie; Kang, Min Ho; Uhm, Han Sup; Choi, Eun Ha; Attri, Pankaj

    2015-09-09

    Bacteria can be inactivated through various physical and chemical means, and these have always been the focus of extensive research. To further improve the methodology for these ends, two types of plasma systems were investigated: nano-second pulsed plasma (NPP) as liquid discharge plasma and an Argon gas-feeding dielectric barrier discharge (Ar-DBD) as a form of surface plasma. To understand the sterilizing action of these two different plasma sources, we performed experiments with Staphylococcus aureus (S. aureus) bacteria (wild type) and multidrug resistant bacteria (Penicillum-resistant, Methicillin-resistant and Gentamicin-resistant). We observed that both plasma sources can inactivate both the wild type and multidrug-resistant bacteria to a good extent. Moreover, we observed a change in the surface morphology, gene expression and β-lactamase activity. Furthermore, we used X-ray photoelectron spectroscopy to investigate the variation in functional groups (C-H/C-C, C-OH and C=O) of the peptidoglycan (PG) resulting from exposure to plasma species. To obtain atomic scale insight in the plasma-cell interactions and support our experimental observations, we have performed molecular dynamics simulations to study the effects of plasma species, such as OH, H2O2, O, O3, as well as O2 and H2O, on the dissociation/formation of above mentioned functional groups in PG.

  2. Conversion of carbon dioxide to carbon monoxide by pulse dielectric barrier discharge plasma

    Science.gov (United States)

    Wang, Taobo; Liu, Hongxia; Xiong, Xiang; Feng, Xinxin

    2017-01-01

    The conversion of carbon dioxide (CO2) to carbon monoxide (CO) was investigated in a non-thermal plasma dielectric barrier discharge (DBD) reactor, and the effects of different process conditions on the CO2 conversion were investigated. The results showed that the increase of input power could optimize the conversion of CO2 to CO. The CO2 conversion and CO yield were negatively correlated with the gas flow rate, but there was an optimum gas flow rate, that made the CO selectivity best. The carrier gas (N2, Ar) was conducive to the conversion of CO2, and the effect of N2 as carrier gas was better than Ar. The conversion of CO2 to CO was enhanced by addition of the catalyst (5A molecular sieve).

  3. One-dimensional electromagnetic band gap structures formed by discharge plasmas in a waveguide

    Energy Technology Data Exchange (ETDEWEB)

    Arkhipenko, V. I.; Simonchik, L. V., E-mail: l.simonchik@dragon.bas-net.by; Usachonak, M. S. [B.I. Stepanov Institute of Physics of the NAS of Belarus, Ave. Nezavisimostsi 68, 220072 Minsk (Belarus); Callegari, Th.; Sokoloff, J. [Université de Toulouse, UPS, INPT, LAPLACE, Laboratoire Plasma et Conversion d' Energie, 118 route de Narbonne, F-31062 Toulouse cedex 9 (France)

    2014-09-28

    We demonstrate the ability to develop one-dimensional electromagnetic band gap structure in X-band waveguide solely by using the positive columns of glow discharges in neon at the middle pressure. Plasma inhomogeneities are distributed uniformly along a typical X-band waveguide with cross section of 23×10 mm². It is shown that electron densities larger than 10¹⁴ cm ⁻³ are needed in order to create an effective one-dimensional electromagnetic band gap structure. Some applications for using the one-dimensional electromagnetic band gap structure in waveguide as a control of microwave (broadband filter and device for variation of pulse duration) are demonstrated.

  4. High Current, High Density Arc Plasma as a New Source for WiPAL

    Science.gov (United States)

    Waleffe, Roger; Endrizzi, Doug; Myers, Rachel; Wallace, John; Clark, Mike; Forest, Cary; WiPAL Team

    2016-10-01

    The Wisconsin Plasma Astrophysics Lab (WiPAL) has installed a new array of nineteen plasma sources (plasma guns) on its 3 m diameter, spherical vacuum vessel. Each gun is a cylindrical, molybdenum, washer-stabilized, arc plasma source. During discharge, the guns are maintained at 1.2 kA across 100 V for 10 ms by the gun power supply establishing a high density plasma. Each plasma source is fired independently allowing for adjustable plasma parameters, with densities varying between 1018 -1019 m-3 and electron temperatures of 5-15 eV. Measurements were characterized using a 16 tip Langmuir probe. The plasma source will be used as a background plasma for the magnetized coaxial plasma gun (MCPG), the Terrestrial Reconnection Experiment (TREX), and as the plasma source for a magnetic mirror experiment. Temperature, density, and confinement results will be presented. This work is supported by the DoE and the NSF.

  5. Analytic non-Maxwellian electron velocity distribution function in a Hall discharge plasma

    Science.gov (United States)

    Shagayda, Andrey; Tarasov, Alexey

    2017-10-01

    The electron velocity distribution function in the low-pressure discharges with the crossed electric and magnetic fields, which occur in magnetrons, plasma accelerators, and Hall thrusters with a closed electron drift, is not Maxwellian. A deviation from equilibrium is caused by a large electron mean free path relative to the Larmor radius and the size of the discharge channel. In this study, we derived in the relaxation approximation the analytical expression of the electron velocity distribution function in a weakly ionized Lorentz plasma with the crossed electric and magnetic fields in the presence of the electron density and temperature gradients in the direction of the electric field. The solution was obtained in the stationary approximation far from boundary surfaces, when diffusion and mobility are determined by the classical effective collision frequency of electrons with ions and atoms. The moments of the distribution function including the average velocity, the stress tensor, and the heat flux were calculated and compared with the classical hydrodynamic expressions. It was shown that a kinetic correction to the drift velocity stems from a contribution of the off-diagonal component of the stress tensor. This correction becomes essential if the drift velocity in the crossed electric and magnetic fields would be comparable to the thermal velocity of electrons. The electron temperature has three different components at a nonzero effective collision frequency and two different components in the limit when the collision frequency tends to zero. It is shown that, in the presence of ionization collisions, the components of the heat flux have additives that are not related to the temperature gradient, and arise because of the electron drift.

  6. Irradiation of silver and agar/silver nanoparticles with argon, oxygen glow discharge plasma, and mercury lamp.

    Science.gov (United States)

    Ahmad, Mahmoud M; Abdel-Wahab, Essam A; El-Maaref, A A; Rawway, Mohammed; Shaaban, Essam R

    2014-01-01

    The irradiation effect of argon, oxygen glow discharge plasma, and mercury lamp on silver and agar/silver nanoparticle samples is studied. The irradiation time dependence of the synthesized silver and agar/silver nanoparticle absorption spectra and their antibacterial effect are studied and compared. In the agar/silver nanoparticle sample, as the irradiation time of argon glow discharge plasma or mercury lamp increases, the peak intensity and the full width at half maximum, FWHM, of the surface plasmon resonance absorption band is increased, however a decrease of the peak intensity with oxygen glow plasma has been observed. In the silver nanoparticle sample, as the irradiation time of argon, oxygen glow discharge plasma or mercury lamp increases, the peak intensity of the surface plasmon resonance absorption band is increased, however, there is no significant change in the FWHM of the surface plasmon resonance absorption band. The SEM results for both samples showed nanoparticle formation with mean size about 50 nm and 40 nm respectively. Throughout the irradiation time with the argon, oxygen glow discharge plasma or mercury lamp, the antibacterial activity of several kinds of Gram-positive and Gram-negative bacteria has been examined.

  7. Model-guided control of hippocampal discharges by local direct current stimulation.

    Science.gov (United States)

    Mina, Faten; Modolo, Julien; Recher, Fanny; Dieuset, Gabriel; Biraben, Arnaud; Benquet, Pascal; Wendling, Fabrice

    2017-05-10

    Neurostimulation is an emerging treatment for drug-resistant epilepsies when surgery is contraindicated. Recent clinical results demonstrate significant seizure frequency reduction in epileptic patients, however the mechanisms underlying this therapeutic effect are largely unknown. This study aimed at gaining insights into local direct current stimulation (LDCS) effects on hyperexcitable tissue, by i) analyzing the impact of electrical currents locally applied on epileptogenic brain regions, and ii) characterizing currents achieving an "anti-epileptic" effect (excitability reduction). First, a neural mass model of hippocampal circuits was extended to accurately reproduce the features of hippocampal paroxysmal discharges (HPD) observed in a mouse model of epilepsy. Second, model predictions regarding current intensity and stimulation polarity were confronted to in vivo mice recordings during LDCS (n = 8). The neural mass model was able to generate realistic hippocampal discharges. Simulation of LDCS in the model pointed at a significant decrease of simulated HPD (in duration and occurrence rate, not in amplitude) for cathodal stimulation, which was successfully verified experimentally in epileptic mice. Despite the simplicity of our stimulation protocol, these results contribute to a better understanding of clinical benefits observed in epileptic patients with implanted neurostimulators. Our results also provide further support for model-guided design of neuromodulation therapy.

  8. Formation of current singularity in a topologically constrained plasma

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Yao [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Princeton Univ., NJ (United States). Dept. of Astrophysical Sciences; Huang, Yi-Min [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Princeton Univ., NJ (United States). Dept. of Astrophysical Sciences; Qin, Hong [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Princeton Univ., NJ (United States). Dept. of Astrophysical Sciences; Univ Sci & Technol China, Dept Modern Phys, Hefei 230026, Anhui, Peoples R China.; Bhattacharjee, A. [Princeton Plasma Physics Lab. (PPPL), Princeton, NJ (United States); Princeton Univ., NJ (United States). Dept. of Astrophysical Sciences

    2016-02-01

    Recently a variational integrator for ideal magnetohydrodynamics in Lagrangian labeling has been developed. Its built-in frozen-in equation makes it optimal for studying current sheet formation. We use this scheme to study the Hahm-Kulsrud-Taylor problem, which considers the response of a 2D plasma magnetized by a sheared field under sinusoidal boundary forcing. We obtain an equilibrium solution that preserves the magnetic topology of the initial field exactly, with a fluid mapping that is non-differentiable. Unlike previous studies that examine the current density output, we identify a singular current sheet from the fluid mapping. These results are benchmarked with a constrained Grad-Shafranov solver. The same signature of current singularity can be found in other cases with more complex magnetic topologies.

  9. Experimental evidence of E × B plasma rotation in a 2.45 GHz hydrogen discharge

    Energy Technology Data Exchange (ETDEWEB)

    Cortázar, O. D., E-mail: daniel.cortazar@uclm.es [Institute for Energy Research-INEI, University of Castilla-La Mancha, C.J. Cela s/n, 13170 Ciudad Real (Spain); Megía-Macías, A. [CERN, BE-ABP-HSL Department, CH1211 Geneva (Switzerland); E.S.S. Bilbao, Polígono Ugaldeguren III, A-7B, 48170 Zamudio (Spain); Tarvainen, O.; Koivisto, H. [Department of Physics, Accelerator Laboratory, University of Jyväskylä, PO Box 35 (YFL), 40500 Jyväskylä (Finland)

    2015-12-15

    An experimental observation of a rotating plasma structure in a 2.45 GHz microwave-driven hydrogen discharge is reported. The rotation is presumably produced by E × B drift. The formation of the rotating plasma structure is sensitive to the strength of the off-resonance static magnetic field. The rotation frequency is on the order of 10 kHz and is affected by the neutral gas pressure and applied microwave power.

  10. Parametric studies of the Hall current plasma thruster

    Science.gov (United States)

    Ashkenazy, J.; Raitses, Y.; Appelbaum, G.

    1998-05-01

    The Hall current plasma thruster accelerates a plasma jet by an axial electric field and an applied radial magnetic field in an annular ceramic channel. A relatively large current density (>0.1 A/cm2) can be obtained as the acceleration mechanism is not limited by space charge effects. Such a device can be used as a small rocket engine on board spacecraft with the advantage of a large jet velocity compared to conventional rocket engines (10000-30000 m/s versus 2000-4800 m/s). An experimental Hall thruster was constructed and operated in a broad range of operating conditions and under various configuration variations. Electrical, magnetic and plasma diagnostics, and as well accurate thrust and gas flow rate measurements, have been used to investigate the dependence of thruster behavior on the applied voltage, gas flow rate, magnetic field, channel geometry and wall material. The studies conducted so far have demonstrated a significant effect of channel material on thruster electrical characteristics and the existence of an optimal channel length for a given flow rate. Representative results highlighting these findings are presented.

  11. Partial discharge measurements on 110kV current transformers. Setting the control value. Case study

    Science.gov (United States)

    Dan, C.; Morar, R.

    2017-05-01

    The case study presents a series of partial discharge measurements, reflecting the state of insulation of 110kV CURRENT TRANSFORMERS located in Sibiu county substations. Measurements were performed based on electrical method, using MPD600: an acquisition and analysis toolkit for detecting, recording, and analyzing partial discharges. MPD600 consists of one acquisition unit, an optical interface and a computer with dedicated software. The system allows measurements of partial discharge on site, even in presence of strong electromagnetic interferences because it provides synchronous acquisition from all measurement points. Therefore, measurements, with the ability to be calibrated, do render: - a value subject to interpretation according to IEC 61869-1:2007 + IEC 61869-2:2012 + IEC 61869-3:2011 + IEC 61869-5:2011 and IEC 60270: 2000; - the possibility to determine the quantitative limit of PD (a certain control value) to which the equipment can be operated safely and repaired with minimal costs (relative to the high costs implied by eliminating the consequences of a failure) identified empirically (process in which the instrument transformer subjected to the tests was completely destroyed).

  12. A high-current rail-type gas switch with preionization by an additional corona discharge

    Energy Technology Data Exchange (ETDEWEB)

    Antipov, E. I.; Belozerov, O. S.; Krastelev, E. G., E-mail: ekrastelev@yandex.ru [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute) (Russian Federation)

    2016-12-15

    The characteristics of a high-current rail-type gas switch with preionization of the gas (air) in a spark gap by an additional corona discharge are investigated. The experiments were performed in a voltage range of 10–45 kV using a two-electrode switch consisting of two cylindrical electrodes with a diameter of 22 mm and a length of 100 mm and a set of laterally located corona-discharge needles. The requirements for the position and size of the needles are defined for which a corona discharge is ignited before a breakdown of the main gap and does not change to a sparking form, and the entire length of the rail electrodes is efficiently used. The fulfillment of these requirements ensures stable operation of the switch with a small variation of the pulse breakdown voltage, which is not more than 1% for a fixed voltage-pulse rise time in the range from 150 ns to 3.5 μs. A short delay time of the switch breakdown makes it possible to control the two-electrode switch by an overvoltage pulse of nanosecond duration.

  13. Removal of cyanide from water by means of plasma discharge technology.

    Science.gov (United States)

    Hijosa-Valsero, María; Molina, Ricardo; Schikora, Hendrik; Müller, Michael; Bayona, Josep M

    2013-03-15

    Two different nonthermal plasma reactors at atmospheric pressure were assessed for the first time for cyanide removal (1 mg L(-1)) from aqueous solutions (0.025 M NaHCO(3)/NaOH buffer, pH 11) at laboratory scale. Both devices were dielectric barrier discharge (DBD) reactors; one of them was a conventional batch reactor (R1) and the other one was a coaxial thin falling water film reactor (R2). A first-order degradation kinetics was proposed for both experiments, obtaining k(R1) = 0.5553 min(-1) and k(R2) = 0.7482 min(-1). The coaxial reactor R2 yielded a removal of 99% within only 3 min. Energy efficiencies (G) were calculated, yielding 1.74 mg kW(-1) h(-1) for R1 and 127.9 mg kW(-1) h(-1) for R2. When the treatment was applied to industrial wastewaters, cyanide elimination was confirmed, although at a lower rate (above 92% removal in 90 min with R2). Therefore, plasma reactors could be a relevant alternative to established advanced oxidation techniques (UV, H(2)O(2), ozonation, etc.) for the removal of cyanide from wastewaters with low organic loads or even drinking waters. Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. Dust coupling parameter of radio-frequency-discharge complex plasma under microgravity conditions

    Science.gov (United States)

    Zhukhovitskii, D. I.; Naumkin, V. N.; Khusnulgatin, A. I.; Molotkov, V. I.; Lipaev, A. M.

    2017-10-01

    Oscillation of particles in a dust crystal formed in a low-pressure radio-frequency gas discharge under microgravity conditions is studied. Analysis of experimental data obtained in our previous study shows that the oscillations are highly isotropic and nearly homogeneous in the bulk of a dust crystal; oscillations of the neighboring particles are significantly correlated. We demonstrate that the standard deviation of the particle radius vector along with the local particle number density fully define the coupling parameter of the particle subsystem. The latter proves to be of the order of 100, which is two orders of magnitude lower than the coupling parameter estimated for the Brownian diffusion of particles with the gas temperature. This means significant kinetic overheating of particles under stationary conditions. A theoretical interpretation of the large amplitude of oscillation implies the increase of particle charge fluctuations in the dust crystal. The theoretical estimates are based on the ionization equation of state for the complex plasma and the equation for the plasma perturbation evolution. They are shown to match the results of experimental data processing. Estimated order of magnitude of the coupling parameter accounts for the existence of the solid-liquid phase transition observed for similar systems in experiments.

  15. Spatial and temporal evolution of ion energies in high power impulse magnetron sputtering plasma discharge

    Science.gov (United States)

    Hecimovic, A.; Ehiasarian, A. P.

    2010-09-01

    High power impulse magnetron sputtering (HIPIMS) is a novel deposition technology successfully implemented on full scale industrial machines. HIPIMS utilizes short pulses of high power delivered to the target in order to generate high amount of metal ions. The life-span of ions between the pulses and their energy distribution could strongly influence the properties and characteristics of the deposited coating. In modern industrial coating machines the sample rotates on a substrate holder and changes its position and distance with regard to the magnetron. Time resolved measurements of the ion energy distribution function (IEDF) at different distances from the magnetron have been performed to investigate the temporal evolution of ions at various distances from target. The measurements were performed using two pressures, 1 and 3 Pa to investigate the influence of working gas pressure on IEDF. Plasma sampling energy-resolved mass spectroscopy was used to measure the IEDF of Ti1+, Ti2+, Ar1+, and Ar2+ ions in HIPIMS plasma discharge with titanium (Ti) target in Ar atmosphere. The measurements were done over a full pulse period and the distance between the magnetron and the orifice of the mass spectrometer was changed from 25 to 215 mm.

  16. Dielectric barrier discharge micro-plasma emission spectrometry for the detection of acetone in exhaled breath.

    Science.gov (United States)

    Yang, Ting; Gao, Dong-Xue; Yu, Yong-Liang; Chen, Ming-Li; Wang, Jian-Hua

    2016-01-01

    Acetone is a predominant volatile organic compound (VOC) in the exhaled breath and a promising biomarker for diabetes and ketoacidosis. A non-thermal micro-plasma generated in a planar dielectric barrier discharge (DBD) is used as a radiation source for the excitation of gaseous acetone followed by its quantification with optical emission spectrometry (OES). Gaseous acetone can be directly sampled, while liquid acetone is evaporated by heated tungsten coil and then introduced into the DBD micro-plasma by a helium carrier flow for performing optical emission and detection at a 519 nm emission line. In the present study, the exhaled breath is collected and transferred into aqueous medium for sampling. With a sampling volume of 7 μL in a micro-drop, a linear range of 40-1600 mg L(-1) is obtained along with a detection limit of 44 ng and a precision of 5.7% RSD. The present system is successfully applied to the determination of breath acetone for both diabetic patients and healthy volunteers. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Experimental investigation of current free double layers in helicon plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Sahu, B. B. [Department of Applied Sciences and Humanities, Dronacharya College of Engineering, Gurgaon 123506 (India); Tarey, R. D. [Department of Physics, Indian Institute of Technology, New Delhi 110016 (India); Ganguli, A. [Centre for Energy Studies, Indian Institute of Technology, New Delhi 110016 (India)

    2014-02-15

    The paper presents investigations of current free double layer (CFDL) that forms in helicon plasmas. In contrast to the other work reporting on the same subject, in the present investigations the double layer (DL) forms in a mirror-like magnetic field topology. The RF compensated Langmuir probe measurements show multiple DLs, which are in connection with, the abrupt fall of densities along with potential drop of about 24 V and 18 V. The DLs strengths (e ΔV{sub p})/(k T{sub e}) are about 9.5 and 6, and the corresponding widths are about 6 and 5 D lengths. The potential drop is nearly equal to the thermal anisotropies between the two plasma regions forming the DL, which is present in the plateau region of mirror, unlike the earlier studies on the DL formation in the region of strong gradients in the magnetic field. Also, it presents a qualitative discussion on the mechanism of DL formation.

  18. Surface modification of polyvinyl alcohol/malonic acid nanofibers by gaseous dielectric barrier discharge plasma for glucose oxidase immobilization

    Energy Technology Data Exchange (ETDEWEB)

    Afshari, Esmail, E-mail: e.afshari@mail.sbu.ac.ir [Laser and Plasma Research Institute, Shahid Beheshti University, Evin, 1983963113 Tehran (Iran, Islamic Republic of); Mazinani, Saeedeh [Amirkabir Nanotechnology Research Institute (ANTRI), Amirkabir University of Technology, 15875-4413, Tehran (Iran, Islamic Republic of); Ranaei-Siadat, Seyed-Omid [Protein Research Center, Shahid Beheshti University, Evin, 1983963113 Tehran (Iran, Islamic Republic of); Ghomi, Hamid [Laser and Plasma Research Institute, Shahid Beheshti University, Evin, 1983963113 Tehran (Iran, Islamic Republic of)

    2016-11-01

    Highlights: • We fabricated polyvinyl alcohol/malonic acid nanofibers using electrospinning. • The surface nanofibers were modified by gaseous (air, nitrogen, CO{sub 2} and argon) dielectric barrier discharge. • Among them, air plasma had the most significant effect on glucose oxidase immobilization. • Chemical analysis showed that after modification of nanofibers by air plasma, the carboxyl group increased. • After air plasma treatment, reusability and storage stability of glucose oxidase immobilized on nanofibers improved. - Abstract: Polymeric nanofiber prepares a suitable situation for enzyme immobilization for variety of applications. In this research, we have fabricated polyvinyl alcohol (PVA)/malonic acid nanofibers using electrospinning. After fabrication of nanofibers, the effect of air, nitrogen, CO{sub 2}, and argon DBD (dielectric barrier discharge) plasmas on PVA/malonic acid nanofibers were analysed. Among them, air plasma had the most significant effect on glucose oxidase (GOx) immobilization. Attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectrum analysis and X-ray photoelectron spectroscopy (XPS) results revealed that in case of air plasma modified nanofibers, the carboxyl groups on the surface are increased. The scanning electron microscopy (SEM) images showed that, after GOx immobilization, the modified nanofibers with plasma has retained its nanofiber structure. Finally, we analysed reusability and storage stability of GOx immobilized on plasma modified and unmodified nanofibers. The results were more satisfactory for modified nanofibers with respect to unmodified ones.

  19. Mechanism of formation of subnanosecond current front in high-voltage pulse open discharge

    Science.gov (United States)

    Schweigert, I. V.; Alexandrov, A. L.; Zakrevsky, Dm. E.; Bokhan, P. A.

    2014-11-01

    The mechanism of subnanosecond current front rise observed previously in the experiment in high-voltage pulse open discharge in helium is studied in kinetic particle-in-cell simulations. The Boltzmann equations for electrons, ions, and fast atoms are solved self-consistently with the Poisson equations for the electrical potential. The partial contributions to the secondary electron emission from the ions, fast atoms, photons, and electrons, bombarding the electrode, are calculated. In simulations, as in the experiment, the discharge glows between two symmetrical cathodes and the anode grid in the midplane at P =6 Torr and the applied voltage of 20 kV. The electron avalanche development is considered for two experimental situations during the last stage of breakdown: (i) with constant voltage and (ii) with decreasing voltage. For case (i), the subnanosecond current front rise is set by photons from the collisional excitation transfer reactions. For the case (ii), the energetic electrons swamp the cathode during voltage drop and provide the secondary electron emission for the subnanosecond current rise, observed in the experiment.

  20. Evaluation of Novel Integrated Dielectric Barrier Discharge Plasma as Ozone Generator

    Directory of Open Access Journals (Sweden)

    Muhammad Nur

    2017-04-01

    Full Text Available This paper presents a characterization of an integrated ozone generator constructed by seven of reactors of Dielectric Barrier Discharge Plasma (DBDP. DBDP a has spiral-cylindrical configuration. Silence plasma produced ozone inside the DBDP reactor was generated by AC-HV with voltage up to 25 kV and maximum frequency of 23 kHz. As a source of ozone, dry air was pumped into the generator and controlled by valves system and a flowmeter. We found ozone concentration increased with the applied voltage, but in contrary, the concentration decreased with the flow rate of dry air. It was also found that a maximum concentration was 20 mg/L and ozone capacity of 48 g/h with an input power of 1.4 kW. Moreover, in this generator, IP efficiency of 8.13 g/kWh was obtained at input power 0.45 kW and air flow rate of 9 L/min. Therefore, be the higher ozone capacity can be produced with higher input power; however, it provided lower IP efficiency. The effect of dry air flow rate and applied voltage on ozone concentrations have been studied. At last, spiral wire copper was very corrosive done to the interaction with ozone, and it is necessary to do a research for finding the best metals as an active electrode inside of the quartz dielectric. Copyright © 2017 BCREC GROUP. All rights reserved Received: 18th July 2016; Revised: 25th September 2016; Accepted: 5th October 2016 How to Cite: Nur, M., Susan, A.I., Muhlisin, Z., Arianto, F., Kinandana, A.W., Nurhasanah, I., Sumariyah, S., Wibawa, P.J., Gunawan, G., Usman, A. (2017. Evaluation of Novel Integrated Dielectric Barrier Discharge Plasma as Ozone Generator. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (1: 24-31 (doi:10.9767/bcrec.12.1.605.24-31 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.1.605.24-31

  1. Positive Voltage Hazard to EMU Crewman from Currents through Plasma

    Science.gov (United States)

    Kramer, Leonard; Hamilton, Doug; Mikatarian, Ronald; Thomas, Joseph; Koontz, Steven

    2010-09-01

    The International Space Station(ISS) in its transit through the ionosphere experiences a variable electrical potential between its bonded structure and the overlying ionospheric plasma. The 160 volt solar arrays on ISS are grounded negative and drive structure to negative floating potential(FP) relative to plasma. This potential is a result of the asymmetric collection properties of currents from ions and electrons moderated by geomagnetic; so called v Å~ B induction distributing an additional 20 volts both positive and negative across ISS’s main structural truss element. Since the space suit or extravehicular mobility unit(EMU) does not protect the crewperson from electrical shock, during extra vehicular activity(EVA) the person is exposed to a hazard from the potential when any of the several metallic suit penetrations come in direct contact with ISS structure. The moisture soaked garment worn by the crewperson and the large interior metal contact areas facilitate currents through the crewperson’s body. There are two hazards; Negative and Positive FP. The Negative hazard is the better known risk created by a shock hazard from arcing of anodized material on the EMU. Negative hazard has been controlled by plasma contactor units(PCU) containing a reserve of Xenon gas which is expelled from ISS. The PCU provide a ground path for the negative charge from the structure to flow to exterior plasma bringing ISS FP closer to zero. The understanding has now emerged that the operation of PCUs to protect the crewmen from negative voltage exposes him to low to moderate positive voltage(≤15V). Positive voltage is also a hazard as it focuses electrons onto exposed metal EMU penetrations completing a circuit from plasma through interior contact with the moist crewman’s body and on to ISS ground through any of several secondary isolated metal penetrations. The resulting direct current from positive voltage exposure is now identified as an electrical shock hazard. This

  2. Magnetohydrodynamic perturbations arising in metallic conductors under the action of the discharge current

    Science.gov (United States)

    Surkaev, A. L.

    2015-07-01

    The presence of radial and axial mechanical perturbations in metallic conductors (cylinders and flat plates) arising under the action of a nanosecond discharge current are proved experimentally. The amplitude of the mechanical perturbations in solid-state conductors oscillates. The radial component of the mechanical perturbation should be considered as a reason for a magnetohydrodynamic instability with mode m = 0 and, accordingly, for the formation of strata at the electrical explosion of the conductor. Data for the electrical explosion of the metallic cylindrical conductor and flat metal sheet (foil) are presented.

  3. Optimization of ECR-breakdown and plasma discharge formation on T-10 tokamak, using X-mode second harmonic of ECR.

    Directory of Open Access Journals (Sweden)

    Roy I.

    2012-09-01

    Full Text Available In order to obtain breakdown and suitable plasma parameters for low-voltage OH start-up, high level of EC-power was injected into T-10 tokamak. Input HF-power was varied in the range of 0.15–1.0 MW. Two HF-launcher systems with different output beams allowed to inject EC-waves with maximum power density 0.25 MW/cm2 and 0.01 MW/cm2. Dependence of breakdown time delay on HF-power was obtained. It was shown, that optimal plasma parameters were achieved in presence of plasma equilibrium currents I=3 kA (input HF-power=1.0 MW. Electron temperature Te=100÷150 eV and electron density ne=5·1012 cm−3 was measured in these discharges. These parameters remained constant during full HF-pulse-length.

  4. UNJUK KERJA REAKTOR PLASMA DIELECTRIC BARRIER DISCHARGE UNTUK PRODUKSI BIODIESEL DARI MINYAK KELAPA SAWIT

    Directory of Open Access Journals (Sweden)

    Ardian Dwi Yudhistira

    2013-10-01

    Full Text Available Biodiesel is one of alternative renewable energy source to substitute diesel fuel. Various biodiesel productionprocesses through transesterification reaction with a variety of catalysts have been developed by previousresearcher. This process still has the disadvantage of a long reaction time, and high energy need. DielectricBarrier Discharge (DBD plasma electro-catalysis may become a solution to overcome the drawbacks in theconventional transesterification process. This process only needs a short time reaction and low energy process.The purpose of this study was to assess the performance of DBD plasma rector in making biodiesel such as: theeffect of high voltage electric value, electrodes gap, mole ratio of methanol / oil, and reaction time. TheResearch method was using GC-MS (Gas Cromatography-Mass Spectrofotometry and FTIR (FourierTransform Infrared Spectrofotometry and then it will be analysed the change of chemical bond betweenreactant and product. So, the reaction mechanism can be predicted. Biodiesel is produced using methanol andpalm oil as reactants and DBD plasma used as reactor in batch system. Then, reactants contacted by highvoltage electric. From the results of this research can be concluded that the reaction mechanism occurs in theprocess is the reaction mechanism of cracking, the higher of electric voltage and the longer of reaction time leadto increasing of product yield. The more of mole ratio of methanol / oil and widening the gap between theelectrodes lead to decreased product yield. From this research, product yield maksimum is 89,8% in the variableof rasio mol metanol/palm oil 3:1, voltage 10 kV, electrode gap 1,5 cm, and reaction time 30 seconds.

  5. Nonlinear currents generated in plasma by a radiation pulse with a frequency exceeding the electron plasma frequency

    Energy Technology Data Exchange (ETDEWEB)

    Grishkov, V. E.; Uryupin, S. A., E-mail: uryupin@sci.lebedev.ru [Russian Academy of Sciences, Lebedev Physical Institute (Russian Federation)

    2016-09-15

    It is shown that the nonlinear currents generated in plasma by a radiation pulse with a frequency exceeding the electron plasma frequency change substantially due to a reduction in the effective electron–ion collision frequency.

  6. Effect of preionization, fluorine concentration, and current density on the discharge uniformity in F2 excimer laser gas mixtures

    NARCIS (Netherlands)

    Mathew, D.; Bastiaens, Hubertus M.J.; Boller, Klaus J.; Peters, P.J.M.

    2007-01-01

    The discharge homogeneity in F2-based excimer laser gas mixtures and its dependence on various key parameters, such as the degree of preionization, preionization delay time, F2 concentration and current density, is investigated in a small x-ray preionized discharge chamber. The spatial and temporal

  7. On-line Monitoring Device for High-voltage Switch Cabinet Partial Discharge Based on Pulse Current Method

    Science.gov (United States)

    Y Tao, S.; Zhang, X. Z.; Cai, H. W.; Li, P.; Feng, Y.; Zhang, T. C.; Li, J.; Wang, W. S.; Zhang, X. K.

    2017-12-01

    The pulse current method for partial discharge detection is generally applied in type testing and other off-line tests of electrical equipment at delivery. After intensive analysis of the present situation and existing problems of partial discharge detection in switch cabinets, this paper designed the circuit principle and signal extraction method for partial discharge on-line detection based on a high-voltage presence indicating systems (VPIS), established a high voltage switch cabinet partial discharge on-line detection circuit based on the pulse current method, developed background software integrated with real-time monitoring, judging and analyzing functions, carried out a real discharge simulation test on a real-type partial discharge defect simulation platform of a 10KV switch cabinet, and verified the sensitivity and validity of the high-voltage switch cabinet partial discharge on-line monitoring device based on the pulse current method. The study presented in this paper is of great significance for switch cabinet maintenance and theoretical study on pulse current method on-line detection, and has provided a good implementation method for partial discharge on-line monitoring devices for 10KV distribution network equipment.

  8. Relation between magnetic fields and electric currents in plasmas

    Directory of Open Access Journals (Sweden)

    V. M. Vasyliunas

    2005-10-01

    Full Text Available Maxwell's equations allow the magnetic field B to be calculated if the electric current density J is assumed to be completely known as a function of space and time. The charged particles that constitute the current, however, are subject to Newton's laws as well, and J can be changed by forces acting on charged particles. Particularly in plasmas, where the concentration of charged particles is high, the effect of the electromagnetic field calculated from a given J on J itself cannot be ignored. Whereas in ordinary laboratory physics one is accustomed to take J as primary and B as derived from J, it is often asserted that in plasmas B should be viewed as primary and J as derived from B simply as (c/4π∇×B. Here I investigate the relation between ∇×B and J in the same terms and by the same method as previously applied to the MHD relation between the electric field and the plasma bulk flow vmv2001: assume that one but not the other is present initially, and calculate what happens. The result is that, for configurations with spatial scales much larger than the electron inertial length λe, a given ∇×B produces the corresponding J, while a given J does not produce any ∇×B but disappears instead. The reason for this can be understood by noting that ∇×B≠4π/cJ implies a time-varying electric field (displacement current which acts to change both terms (in order to bring them toward equality; the changes in the two terms, however, proceed on different time scales, light travel time for B and electron plasma period for J, and clearly the term changing much more slowly is the one that survives. (By definition, the two time scales are equal at λe. On larger scales, the evolution of B (and hence also of ∇×B is governed by

  9. Plasma current start-up by the outer ohmic heating coils in the Saskatchewan TORus Modified (STOR-M) iron core tokamak

    Science.gov (United States)

    Mitarai, O.; Xiao, C.; McColl, D.; Dreval, M.; Hirose, A.; Peng, M.

    2015-03-01

    A plasma current up to 15 kA has been driven with outer ohmic heating (OH) coils in the STOR-M iron core tokamak. Even when the inner OH coil is disconnected, the outer OH coils alone can induce the plasma current as primary windings and initial breakdown are even easier in this coil layout. This result suggests a possibility to use an iron core in a spherical tokamak to start up the plasma current without a central solenoid. The effect of the iron core saturation on the extension of the discharge pulse length has been estimated for further experiments in the STOR-M tokamak.

  10. Dielectric barrier discharge atmospheric cold plasma treatments to inhibit foodborne pathogens and tulane virus in Romaine lettuce

    Science.gov (United States)

    Dielectric barrier discharge atmospheric cold plasma (ACP) treatment is a novel, promising antimicrobial method. Of particular interest is the potential for ACP as an in-package decontamination method for fresh produce. Such tools are highly desirable, as they minimize the possibility of post-proces...

  11. Electromagnetic Interference from Swimming Pool Generator Current Causing Inappropriate ICD Discharges

    Directory of Open Access Journals (Sweden)

    Edward Samuel Roberto

    2017-01-01

    Full Text Available Electromagnetic interference (EMI includes any electromagnetic field signal that can be detected by device circuitry, with potentially serious consequences: incorrect sensing, pacing, device mode switching, and defibrillation. This is a unique case of extracardiac EMI by alternating current leakage from a submerged motor used to recycle chlorinated water, resulting in false rhythm detection and inappropriate ICD discharge. A 31-year-old female with arrhythmogenic right ventricular cardiomyopathy and Medtronic dual-chamber ICD placement presented after several inappropriate ICD shocks at the public swimming pool. Patient had never received prior shocks and device was appropriate at all regular follow-ups. Intracardiac electrograms revealed unique, high-frequency signals at exactly 120 msec suggestive of EMI from a strong external source of alternating current. Electrical artifact was incorrectly sensed as a ventricular arrhythmia which resulted in discharge. ICD parameters including sensing, pacing thresholds, and impedance were all normal suggesting against device malfunction. With device failure and intracardiac sources excluded, EMI was therefore strongly suspected. Avoidance of EMI source brought complete resolution with no further inappropriate shocks. After exclusion of intracardiac interference, device malfunction, and abnormal settings, extracardiac etiologies such as EMI must be thoughtfully considered and excluded. Elimination of inappropriate shocks is to “first, do no harm.”

  12. Design and characterization of a direct current glow discharge lamp for analytical applications

    Energy Technology Data Exchange (ETDEWEB)

    Dimri, A.K. [Central Scientific Instruments Organisation, Sector-30, Chandigarh 160030 (India)]. E-mail: akrdimri@yahoo.com; Paul, A.K. [Central Scientific Instruments Organisation, Sector-30, Chandigarh 160030 (India); Bajpai, R.P. [Central Scientific Instruments Organisation, Sector-30, Chandigarh 160030 (India)

    2004-11-08

    This paper describes a compact, small volume direct current glow discharge lamp operating at low wattage for atomic emission spectrometric analysis and its process optimization for copper and brass solid samples. The design aspects, fundamental characteristics and analytical performance are described in detail. The discharge is observed end-on, with water-cooled cathode surface parallel to the spectroscopic entrance slit. The anode diameter is 7 mm and the minimum sample diameter required is 20 mm. The sample is located outside the lamp for easy access and interchangeability. The lamp is powered by a dc power supply capable of delivering 300 mA (max.) and 1500 V. The studies of fundamental characteristics include the current-voltage relationship and their dependence on pressure and the emission intensity of copper spectral line (324.7 nm). The studies were made in the pressure range of 2-7 mbar. Long-term stability of optical emission spectra was also recorded to be within {+-}0.75%. The performance of the lamp is quite linear in the pressure range 3.5-7 mbar at an applied voltage of about 450 V.

  13. The component content of active particles in a plasma-chemical reactor based on volume barrier discharge

    Energy Technology Data Exchange (ETDEWEB)

    Soloshenko, I A [Institute of Physics of National Academy of Sciences of Ukraine, 46 Nauki Avenue, 03028, Kiev (Ukraine); Tsiolko, V V [Institute of Physics of National Academy of Sciences of Ukraine, 46 Nauki Avenue, 03028, Kiev (Ukraine); Pogulay, S S [Institute of Physics of National Academy of Sciences of Ukraine, 46 Nauki Avenue, 03028, Kiev (Ukraine); Terent' yeva, A G [Institute of Physics of National Academy of Sciences of Ukraine, 46 Nauki Avenue, 03028, Kiev (Ukraine); Bazhenov, V Yu [Institute of Physics of National Academy of Sciences of Ukraine, 46 Nauki Avenue, 03028, Kiev (Ukraine); Shchedrin, A I [Institute of Physics of National Academy of Sciences of Ukraine, 46 Nauki Avenue, 03028, Kiev (Ukraine); Ryabtsev, A V [Institute of Physics of National Academy of Sciences of Ukraine, 46 Nauki Avenue, 03028, Kiev (Ukraine); Kuzmichev, A I [National Technical University ' KPI' , 37 Peremogy Avenue, KPI-2230, 03056, Kiev, (Ukraine)

    2007-02-01

    In this paper the results of theoretical and experimental studies of the component content of active particles formed in a plasma-chemical reactor composed of a multiple-cell generator of active particles, based on volume barrier discharge, and a working chamber are presented. For calculation of the content of uncharged plasma components an approach is proposed which is based on averaging of the power introduced over the entire volume. Advantages of such an approach lie in an absence of fitting parameters, such as the dimensions of microdischarges, their surface density and rate of breakdown. The calculation and the experiment were accomplished with the use of dry air (20% relative humidity) as the plasma generating medium. Concentrations of O{sub 3}, HNO{sub 3}, HNO{sub 2}, N{sub 2} O{sub 5} and NO{sub 3} were measured experimentally in the discharge volume and working chamber for the residence time of particles on a discharge of 0.3 s and more and discharge specific power of 1.5 W cm{sup -3}. It has been determined that the best agreement between the calculation and the experiment occurs at calculated gas medium temperatures in the discharge plasma of about 400-425 K, which correspond to the experimentally measured rotational temperature of nitrogen. In most cases the calculated concentrations of O{sub 3}, HNO{sub 3}, HNO{sub 2}, N{sub 2}O{sub 5} and NO{sub 3} for the barrier discharge and the working chamber are in fairly good agreement with the respective measured values.

  14. Observation of SOL Current Correlated with MHD Activity in NBI-heated DIII-D Tokamak Discharges

    Energy Technology Data Exchange (ETDEWEB)

    H. Takahashi; E.D. Fredrickson; M.J. Schaffer; M.E. Austin; T.E. Evans; L.L. Lao; J.G. Watkins

    2004-03-26

    This work investigates the potential roles played by the scrape-off-layer current (SOLC) in MHD activity of tokamak plasmas, including effects on stability. SOLCs are found during MHD activity that are: (1) slowly growing after a mode-locking-like event, (2) oscillating in the several kHz range and phase-locked with magnetic and electron temperature oscillations, (3) rapidly growing with a sub-ms time scale during a thermal collapse and a current quench, and (4) spiky in temporal behavior and correlated with spiky features in Da signals commonly identified with the edge localized mode (ELM). These SOLCs are found to be an integral part of the MHD activity, with a propensity to flow in a toroidally non-axisymmetric pattern and with magnitude potentially large enough to play a role in the MHD stability. Candidate mechanisms that can drive these SOLCs are identified: (a) toroidally non-axisymmetric thermoelectric potential, (b) electromotive force (EMF) from MHD activity, and (c) flux swing, both toroidal and poloidal, of the plasma column. An effect is found, stemming from the shear in the field line pitch angle, that mitigates the efficacy of a toroidally non-axisymmetric SOLC to generate a toroidally non-axisymmetric error field. Other potential magnetic consequences of the SOLC are identified: (i) its error field can introduce complications in feedback control schemes for stabilizing MHD activity and (ii) its toroidally non-axisymmetric field can be falsely identified as an axisymmetric field by the tokamak control logic and in equilibrium reconstruction. The radial profile of a SOLC observed during a quiescent discharge period is determined, and found to possess polarity reversals as a function of radial distance.

  15. Conception of a novel spray tower plasma-reactor in a spatial post-discharge configuration: Pollutants remote treatment.

    Science.gov (United States)

    Ferhat, Mohamed Fouad; Ghezzar, Mouffok Redouane; Smaïl, Bentaïba; Guyon, Cedric; Ognier, Stéphanie; Addou, Ahmed

    2017-01-05

    This paper describes a novel gliding Arc discharge reactor producing a non-thermal plasma at atmospheric pressure in humid air. The ionized gas is generated in a spray-tower absorber for the treatment of organic pollutants. The reactor configuration enables the plasma-degradation of micro-droplets effluents in the spatial post-discharge mode. This type of design allows to exclude the direct contact between the plasma plume and the liquid to be treated in order to avoid the liquid heating and the flame extinction problems. A hydrodynamic study coupling 'Navier-Stokes' equations and those of 'Convection-Diffusion' allowed to calculate the concentration profiles and the droplet falling velocity. The stripping of phenol was studied to valid the hydrodynamic approach. Experiences and simulations showed that after 1h of treatment, only 5% of the compound was transferred into the plasma phase. The spatiality of the novel reactor allowed a degradation rate of 100% for catechol after 38min of plasma-treatment. For 4-nitrophenol, the degradation rate reached 90% after 120min. Phenol and its by-products degradation were totally degraded by combining the spatiality of the reactor and the temporal post-discharge. A degradation mechanism was proposed and a plasmachemical reaction in relation with the pernitrous acid species was confirmed. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. The effect of displacement current on fast-pulsed dielectric barrier discharges

    CERN Document Server

    Bletzinger, P

    2003-01-01

    Applied voltage and gas pressure dependent electrical power deposition efficiencies in a short voltage pulse excited dielectric barrier discharge have been measured. The effect of time delay between the onset of gas breakdown, peak conduction current and the applied voltage pulse with increasing gas pressure leads to higher net power deposition at lower E/n, where E is the electric field and n is the gas density. An accurate measurement of the power deposition requires careful estimation of the displacement current with the applied voltage as the voltage time derivative dV/dt increases. The variation of optical emission intensity measurements of Ar 2p sub 1 -1s sub 2 , N sub 2 C-B and N sub 2 sup + B-X transitions with increasing gas pressure validated the conclusions reached from the time resolved electrical measurements.

  17. PHYSICS OF GASES, PLASMAS, AND ELECTRIC DISCHARGES: Diagnosis of Methane Plasma Generated in an Atmospheric Pressure DBD Micro-Jet by Optical Emission Spectroscopy

    Science.gov (United States)

    Zhang, Jun-Feng; Bian, Xin-Chao; Chen, Qiang; Liu, Fu-Ping; Liu, Zhong-Wei

    2009-03-01

    Diagnosis of methane plasma, generated in an atmospheric pressure dielectric barrier discharge (DBD) microplasma jet with a quartz tube as dielectric material by a 25 kHz sinusoidal ac power source, is conducted by optical emission spectroscopy (OES). The reactive radicals in methane plasma such as CH, C2, and Hα are detected insitu by OES. The possible dissociation mechanism of methane in diluted Ar plasma is deduced from spectra. In addition, the density of CH radical, which is considered as one of the precursors in diamond-like (DLC) film formation, affected by the parameters of input voltage and the feed gas flow rate, is emphasized. With the Boltzmann plots, four Ar atomic spectral lines (located at 675.28nm, 687.13nm, 738.40nm and 794.82nm, respectively) are chosen to calculate the electron temperature, and the dependence of electron temperature on discharge parameters is also investigated.

  18. Efficient new process for the desulfurization of mixtures of air and hydrogen sulfide via a dielectric barrier discharge plasma

    Directory of Open Access Journals (Sweden)

    S. Dahle

    2015-10-01

    Full Text Available The efficient removal of hydrogen sulfide, H2S, from streams of H2S in air via a dielectric barrier discharge (DBD plasma has been investigated using a quadrupole mass spectrometer. A suitable plasma device with a reservoir for storing sorbent powder of various kinds within the plasma region was constructed. Plasma treatments of gas streams with high concentrations of hydrogen sulfide in air yielded a removal of more than 98% of the initial hydrogen sulfide and a deposition of sulfur at the surface of the dielectric, while small amounts of sulfur dioxide were generated. The presence of calcium carbonate within the plasma region of the DBD device resulted in the removal of over 99% of the initial hydrogen sulfide content and the removal of 98% of the initial sulfur dioxide impurities from the gas mixture.

  19. Fast wave current drive in neutral beam heated plasmas on DIII-D

    Energy Technology Data Exchange (ETDEWEB)

    Petty, C.C.; Forest, C.B.; Pinsker, R.I.; deGrassie, J.S. [General Atomics, San Diego, California 92186 (United States); Baity, F.W. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Callis, R.W.; Cary, W.P.; Chiu, S.C.; Freeman, R.L.; Gohil, P.; Groebner, R.J.; Ikezi, H. [General Atomics, San Diego, California 92186 (United States); Jaeger, E.F. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Lin-Liu, Y.R. [General Atomics, San Diego, California 92186 (United States); Murakami, M. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Porkolab, M. [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Prater, R. [General Atomics, San Diego, California 92186 (United States); Rice, B.W. [Lawrence Livermore National Laboratory, Livermore, California 94551 (United States)

    1997-04-01

    The physics of non-inductive current drive and current profile control using the fast magnetosonic wave has been demonstrated on the DIII-D tokamak. In non-sawtoothing discharges formed by neutral beam injection (NBI), the radial profile of the fast wave current drive (FWCD) was determined by the response of the loop voltage profile to co, counter, and symmetric antenna phasings, and was found to be in good agreement with theoretical models. The application of counter FWCD increased the magnetic shear reversal of the plasma and delayed the onset of sawteeth, compared to co FWCD. The partial absorption of fast waves by energetic beam ions at high harmonics of the ion cyclotron frequency was also evident from a build up of fast particle pressure near the magnetic axis and a correlated increase in the neutron rate. The anomalous fast particle pressure and neutron rate increased with increasing NBI power and peaked when a harmonic of the deuterium cyclotron frequency passed through the center of the plasma. The experimental FWCD efficiency was highest at 2 T where the interaction between the fast waves and the beam ions was weakest; as the magnetic field strength was lowered, the FWCD efficiency decreased to approximately half of the maximum theoretical value. {copyright} {ital 1997 American Institute of Physics.}

  20. 3D MHD modelling of low current-high voltage dc plasma torch under restrike mode

    Science.gov (United States)

    Lebouvier, A.; Delalondre, C.; Fresnet, F.; Cauneau, F.; Fulcheri, L.

    2012-01-01

    We present in this paper a magnetohydrodynamic (MHD) modelling of the gliding arc behaviour of a dc plasma torch operating with air under low current and high voltage conditions. The low current leads to instabilities and difficulties with simulating the process because the magnetic field is not sufficient to constrict the arc. The model is 3D, time dependent and the MHD equations are solved using CFD software Code_Saturne®. Although the arc is definitively non-local thermodynamic equilibrium (LTE), the LTE assumption is considered as a first approach. The injection of air is tangential. A hot gas channel reattachment model has been used to simulate the restriking process of the arc root. After the description of the model, the most appropriate electrical voltage breakdown parameter has been selected in comparing with experimental results. A typical operating point is then studied in detail and shows the helical shape of the arc discharge in the nozzle. Finally, the mass flow rate and the current have been varied in the range 0.16-0.5 g s-1 and 100-300 mA, respectively, corresponding to typical glidarc operating points of our experimental plasma torch. The model shows good consistency with experimental data in terms of global behaviour, arc length, mean voltage and glidarc frequency.

  1. Study of nanosecond discharges in different H2 air mixtures at atmospheric pressure for plasma-assisted applications

    Science.gov (United States)

    Bourdon, Anne; Kobayashi, Sumire; Bonaventura, Zdenek; Tholin, Fabien; Popov, Nikolay

    2016-09-01

    This paper presents 2D simulations of nanosecond pulsed discharges between two point electrodes in different H2/air mixtures and in air at atmospheric pressure. A fluid model is coupled with detailed kinetic schemes for air and different H2/air mixtures to simulate the discharge dynamics. First, as the positive and negative ionization waves propagate in the interelectrode gap, it has been observed that in H2/air mixtures with equivalence ratios between 0.3 and 2, major positive ions produced by the nanosecond discharge are N2+,O2+and HN2+.The discharge dynamics is shown to vary only slightly for equivalence ratios of the H2/air mixture between 0.3 and 2. Then, as the discharge transits to a nanosecond spark discharge, we have studied the different chemical reactions that lead to fast gas heating and to the production of radicals, as O,H and OH. Both thermal and chemical effects of the nanosecond spark discharge are of interest for plasma assisted combustion applications. This work has been supported by the project DRACO (Grant No. ANR-13-IS09-0004) and the french russian LIA Kappa.

  2. Removal of priority pollutants from water by means of dielectric barrier discharge atmospheric plasma.

    Science.gov (United States)

    Hijosa-Valsero, María; Molina, Ricardo; Schikora, Hendrik; Müller, Michael; Bayona, Josep M

    2013-11-15

    Two different nonthermal plasma reactors at atmospheric pressure were assessed for the removal of organic micropollutants (atrazine, chlorfenvinfos, 2,4-dibromophenol, and lindane) from aqueous solutions (1-5 mg L(-1)) at laboratory scale. Both devices were dielectric barrier discharge (DBD) reactors; one was a conventional batch reactor (R1) and the other a coaxial thin-falling-water-film reactor (R2). A first-order degradation kinetics was proposed for both experiments. The kinetic constants (k) were slightly faster in R1 (0.534 min(-1) for atrazine; 0.567 min(-1) for chlorfenvinfos; 0.802 min(-1) for 2,4-dibromophenol; 0.389 min(-1) for lindane) than in R2 (0.104 min(-1) for atrazine; 0.523 min(-1) for chlorfenvinfos; 0.273 min(-1) for 2,4-dibromophenol; 0.294 min(-1) for lindane). However, energy efficiencies were about one order of magnitude higher in R2 (89 mg kW(-1) h(-1) for atrazine; 447 mg kW(-1) h(-1) for c hlorfenvinfos; 47 mg kW(-1) h(-1) for 2,4-dibromophenol; 50 mg kW(-1) h(-1) for lindane) than in R1. Degradation by -products of all four compounds were identified in R1. As expected, when the plasma treatment (R1) was applied to industrial wastewater spiked with atrazine or lindane, micropollutant removal was also achieved, although at a lower rate than with aqueous solutions (k = 0.117 min(-1) for atrazine; k = 0.061 min(-1) for lindane). Copyright © 2013 Elsevier B.V. All rights reserved.

  3. Synthesis of thick diamond films by direct current hot-cathode plasma chemical vapour deposition

    CERN Document Server

    Jin Zeng Sun; Bai Yi Zhen; Lu Xian Yi

    2002-01-01

    The method of direct current hot-cathode plasma chemical vapour deposition has been established. A long-time stable glow discharge at large discharge current and high gas pressure has been achieved by using a hot cathode in the temperature range from 1100 degree C to 1500 degree C and non-symmetrical configuration of the poles, in which the diameter of the cathode is larger than that of anode. High-quality thick diamond films, with a diameter of 40-50 mm and thickness of 0.5-4.2 mm, have been synthesized by this method. Transparent thick diamond films were grown over a range of growth rates between 5-10 mu m/h. Most of the thick diamond films have thermal conductivities of 10-12 W/K centre dot cm. The thick diamond films with high thermal conductivity can be used as a heat sink of semiconducting laser diode array and as a heat spreading and isolation substrate of multichip modules. The performance can be obviously improved

  4. The role of the gas/plasma plume and self-focusing in a gas-filled capillary discharge waveguide for high-power laser-plasma applications

    CERN Document Server

    Ciocarlan, C.; Islam, M. R.; Ersfeld, B.; Abuazoum, S.; Wilson, R.; Aniculaesei, C.; Welsh, G. H.; Vieux, G.; Jaroszynski, D. A.; 10.1063/1.4822333

    2013-01-01

    The role of the gas/plasma plume at the entrance of a gas-filled capillary discharge plasma waveguide in increasing the laser intensity has been investigated. Distinction is made between neutral gas and hot plasma plumes that, respectively, develop before and after discharge breakdown. Time-averaged measurements show that the on-axis plasma density of a fully expanded plasma plume over this region is similar to that inside the waveguide. Above the critical power, relativistic and ponderomotive selffocusing lead to an increase in the intensity, which can be nearly a factor of 2 compared with the case without a plume. When used as a laser plasma wakefield accelerator, the enhancement of intensity can lead to prompt electron injection very close to the entrance of the waveguide. Self-focusing occurs within two Rayleigh lengths of the waveguide entrance plane in the region, where the laser beam is converging. Analytical theory and numerical simulations show that, for a density of 3.01018 cm3, the peak normalized...

  5. Spectroscopic Study of Plasma Polymerized a-C:H Films Deposited by a Dielectric Barrier Discharge

    Directory of Open Access Journals (Sweden)

    Thejaswini Halethimmanahally Chandrashekaraiah

    2016-07-01

    Full Text Available Plasma polymerized a-C:H thin films have been deposited on Si (100 and aluminum coated glass substrates by a dielectric barrier discharge (DBD operated at medium pressure using C2Hm/Ar (m = 2, 4, 6 gas mixtures. The deposited films were characterized by Fourier transform infrared reflection absorption spectroscopy (FT-IRRAS, Raman spectroscopy, and ellipsometry. FT-IRRAS revealed the presence of sp3 and sp2 C–H stretching and C–H bending vibrations of bonds in the films. The presence of D and G bands was confirmed by Raman spectroscopy. Thin films obtained from C2H4/Ar and C2H6/Ar gas mixtures have ID/IG ratios of 0.45 and 0.3, respectively. The refractive indices were 2.8 and 3.1 for C2H4/Ar and C2H6/Ar films, respectively, at a photon energy of 2 eV.

  6. STUDENT AWARD FINALIST: Oxygen Pathways in Streamer Discharge for Transient Plasma Ignition

    Science.gov (United States)

    Pendleton, S. J.; Bowman, S.; Singleton, D.; Watrous, J.; Carter, C.; Lempert, W.; Gundersen, M. A.

    2011-10-01

    The use of streamers for the ignition of fuels, also known as transient plasma ignition (TPI), has been shown in a variety of engines to improve combustion through decreased ignition delay, increased lean burn capability and increased energy release relative to conventional spark ignition. The mechanisms behind these improvements, however, remain poorly understood. Temperature measurements by optical emission spectroscopy demonstrate that ignition by TPI is a nonthermal process, and thus is almost entirely dependent on the production and presence of electron impact-created active species in the discharge afterglow. Of particular interest are active oxygen species due to their relatively long lifetimes at high pressures and the pivotal role they play in combustion reactions. In order to elucidate the oxygen pathways, here we report the investigation of the temporal evolution of the populations of atomic oxygen and ozone by use of two-photon absorption laser induced fluorescence (TALIF) and UV absorption, respectively. Experimental results are presented and compared to kinetic modeling of the streamers. Future experiments are proposed to better understand the physics behind TPI. Supported by NSF, AFOSR, NumerEx-ONR, AFRL-WPAFB.

  7. Dechlorination and decomposition of chloroform induced by glow discharge plasma in an aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yongjun, E-mail: lyjglow@sohu.com [College of Environmental Science & Engineering, Dalian Maritime University, Dalian 116026 (China); Brook Byers Institute for Sustainable Systems, Georgia Institute of Technology, Atlanta 30332 (United States); Crittenden, John C. [Brook Byers Institute for Sustainable Systems, Georgia Institute of Technology, Atlanta 30332 (United States); Wang, Lei [College of Environmental Science & Engineering, Xiamen University of Technology, Xiamen 361024 (China); Liu, Panliang [Brook Byers Institute for Sustainable Systems, Georgia Institute of Technology, Atlanta 30332 (United States)

    2016-05-05

    Highlights: • Hydrated electrons played an important role for chloroform decomposition. • Oxygen enhanced hydrolyses are critical for the chloroform mineralization. • Energy efficiency of GDP is higher than those of the typical competitive processes. - Abstract: In this study, efficient dechlorination and decomposition of chloroform (CF) induced by glow discharge plasma (GDP) in contact with a sodium sulfate solution was investigated. Intermediate byproducts were determined by ionic chromatography and headspace gas chromatography, respectively. Results showed that CF can be effectively dechlorinated and decomposed under the action of GDP. Both removal and dechlorination of CF increased with increasing pH and with addition of hydroxyl radical scavengers to the solution. Addition of H{sub 2}O{sub 2} to the solution slightly decreased the CF removal. Formic acid, oxalic acid and dichloromethane were determined as the major intermediate byproducts. Final products were carbon dioxide and hydrochloric acid. Hydrated electrons were the most likely active species responsible for initiation of the dechlorination, and hydroxyl radicals may be the ones for the oxidation of the organic intermediate byproducts. Hydrolyses of the chloromethyl radicals contributed much in the mineralization of the organic chlorine. Reaction mechanism was proposed based on the dechlorination kinetics and the distribution of intermediate byproducts.

  8. Removal of caffeine from water by combining dielectric barrier discharge (DBD plasma with goethite

    Directory of Open Access Journals (Sweden)

    Jian Wang

    2017-07-01

    Full Text Available In this research, dielectric barrier discharge plasma was developed to cooperate with goethite for removing caffeine in aqueous solution. Goethite was characterized by X-ray diffraction and scanning electron microscopy. The effects of input power, initial concentration and catalysts concentration on the removal efficiency of caffeine were evaluated. Furthermore, the degradation pathways of caffeine were also discussed preliminarily. In the case of caffeine concentration at 50 mg L−1, the degradation efficiency of caffeine was improved from 41% to 94% after 24 min on the conditions of input power of 75 W by combining goethite catalysts (2.5 g L−1, while the energy efficiency could be enhanced 1.6–2.3 times compared to the single DBD reactor. The reaction mechanism experiments demonstrated that attack by hydroxyl radical and ozone was the main degradation process of caffeine in aqueous solution. These studies also provided a theoretical and practical basis for the application of DBD-goethite in treatment of caffeine from water.

  9. Investigation of multifractal nature of floating potential fluctuations obtained from a dc glow discharge magnetized plasma

    Science.gov (United States)

    Shaw, Pankaj Kumar; Saha, Debajyoti; Ghosh, Sabuj; Janaki, M. S.; Iyengar, A. N. Sekar

    2017-03-01

    In this paper, multifractal detrended fluctuation analysis (MF-DFA) has been used to analyze the floating potential fluctuations obtained with a Langmuir probe from a dc glow discharge magnetized plasma device. The generalized Hurst exponents (h(q)) , local fluctuation function (Fq(s)) , the Rényi exponents (τ(q)) and the multifractal spectrum F(α) have been calculated by applying the MF-DFA method. The result of the MF-DFA shows the multifractal nature of these fluctuations. We have investigated the influence of magnetic field on the multifractal nature of the fluctuations and it is seen that degree of multifractality is reduced with the increase in the magnetic field strength. The values of h(q) have been restricted between 0.7 and 1 for the magnetized fluctuations. This result is evidence of the existence of long-range correlations in the fluctuations. Furthermore, we employed shuffle and surrogate approaches to analyze the origins of multifractality. Comparing the MF-DFA results for the data set to those for shuffled and surrogate series, we have found that its multifractal nature is due to the existence of significant long-term correlation.

  10. Biodiesel production using fatty acids from food industry waste using corona discharge plasma technology.

    Science.gov (United States)

    Cubas, A L V; Machado, M M; Pinto, C R S C; Moecke, E H S; Dutra, A R A

    2016-01-01

    This article aims to describe an alternative and innovative methodology to transform waste, frying oil in a potential energy source, the biodiesel. The biodiesel was produced from fatty acids, using a waste product of the food industry as the raw material. The methodology to be described is the corona discharge plasma technology, which offers advantages such as acceleration of the esterification reaction, easy separation of the biodiesel and the elimination of waste generation. The best conditions were found to be an oil/methanol molar ratio of 6:1, ambient temperature (25 °C) and reaction time of 110 min and 30 mL of sample. The acid value indicates the content of free fatty acids in the biodiesel and the value obtained in this study was 0.43 mg KOH/g. Peaks corresponding to octadecadienoic acid methyl ester, octadecanoic acid methyl ester and octadecenoic acid methyl ester, from the biodiesel composition, were identified using GC-MS. A major advantage of this process is that the methyl ester can be obtained in the absence of chemical catalysts and without the formation of the co-product (glycerin). Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Effects of pulse polarity on nanosecond pulse driven dielectric barrier discharge plasma actuators

    Science.gov (United States)

    Dawson, Robyn A.; Little, Jesse

    2014-01-01

    Nanosecond pulse driven dielectric barrier discharge plasma actuators are studied in quiescent air using a power supply capable of producing negative and positive polarity waveforms. High voltage pulses are applied to the exposed electrode of typical asymmetric actuator geometry. In addition to polarity, the effects of pulse amplitude, actuator length, and dielectric thickness are also investigated. Schlieren images are used to estimate the relative near surface gas heating, while electrical measurements are acquired simultaneously. Negative polarity pulses develop slightly more energy per unit length for thin dielectrics, while positive polarity is slightly higher for thick dielectrics. In most cases, the difference in per unit length energy produced by positive and negative pulses on equivalent actuators is not outside the measurement uncertainty. Negative polarity pulses are found to produce a stronger pressure wave for a given peak voltage and pulse energy across the test matrix. Results indicate that the negative polarity pulse more efficiently couples electrical energy to the near surface gas as heat. This suggests negative polarity pulses may be preferred for aerodynamic flow control applications employing this actuator arrangement.

  12. Removal of priority pollutants from water by means of dielectric barrier discharge atmospheric plasma

    Energy Technology Data Exchange (ETDEWEB)

    Hijosa-Valsero, María, E-mail: mhijv@unileon.es [Instituto de Diagnóstico Ambiental y Estudios del Agua (IDAEA), CID, CSIC, C/Jordi Girona 18-26, E-08034 Barcelona (Spain); Molina, Ricardo, E-mail: ricardo.molina@cid.csic.es [Instituto de Química Avanzada de Cataluña (IQAC), CID, CSIC, C/Jordi Girona 18-26, E-08034 Barcelona (Spain); Schikora, Hendrik, E-mail: hendrik.schikora@igb.fraunhofer.de [Fraunhofer IGB, Nobelstraße 12, 70569 Stuttgart (Germany); Müller, Michael, E-mail: michael.mueller@igb.fraunhofer.de [Fraunhofer IGB, Nobelstraße 12, 70569 Stuttgart (Germany); Bayona, Josep M., E-mail: josep.bayona@cid.csic.es [Instituto de Diagnóstico Ambiental y Estudios del Agua (IDAEA), CID, CSIC, C/Jordi Girona 18-26, E-08034 Barcelona (Spain)

    2013-11-15

    Highlights: • DBD plasma reactors were used to remove pollutants from aqueous solutions. • Atrazine, chlorfenvinfos, 2,4-dibromophenol and lindane were studied. • First-order degradation kinetics were observed for all the compounds. • Degradation by-products were identified by GC–MS. • Treatment efficiencies were lower in industrial wastewater than in pure water. -- Abstract: Two different nonthermal plasma reactors at atmospheric pressure were assessed for the removal of organic micropollutants (atrazine, chlorfenvinfos, 2,4-dibromophenol, and lindane) from aqueous solutions (1–5 mg L{sup −1}) at laboratory scale. Both devices were dielectric barrier discharge (DBD) reactors; one was a conventional batch reactor (R1) and the other a coaxial thin-falling-water-film reactor (R2). A first-order degradation kinetics was proposed for both experiments. The kinetic constants (k) were slightly faster in R1 (0.534 min{sup −1} for atrazine; 0.567 min{sup −1} for chlorfenvinfos; 0.802 min{sup −1} for 2,4-dibromophenol; 0.389 min{sup −1} for lindane) than in R2 (0.104 min{sup −1} for atrazine; 0.523 min{sup −1} for chlorfenvinfos; 0.273 min{sup −1} for 2,4-dibromophenol; 0.294 min{sup −1} for lindane). However, energy efficiencies were about one order of magnitude higher in R2 (89 mg kW{sup −1} h{sup −1} for atrazine; 447 mg kW{sup −1} h{sup −1} for chlorfenvinfos; 47 mg kW{sup −1} h{sup −1} for 2,4-dibromophenol; 50 mg kW{sup −1} h{sup −1} for lindane) than in R1. Degradation by-products of all four compounds were identified in R1. As expected, when the plasma treatment (R1) was applied to industrial wastewater spiked with atrazine or lindane, micropollutant removal was also achieved, although at a lower rate than with aqueous solutions (k = 0.117 min{sup −1} for atrazine; k = 0.061 min{sup −1} for lindane)

  13. Imaging diagnostics of pulsed plasma discharges in saline generated with various sharp pin powered electrodes

    Science.gov (United States)

    Asimakoulas, L.; Karim, M. L.; Dostal, L.; Krcma, F.; Graham, W. G.; Field, T. A.

    2016-09-01

    Plasmas formed by 1 ms pulses of between 180 and 300 V applied to sharp pin-like electrodes immersed in saline solution have been imaged with a Photron SA-X2 fast framing camera and an Andor iStar 510 ICCD camera. Stainless steel, Tungsten and Gold electrodes were investigated with tip diameters of 30 μm, 1 μm and fast framing results show that light emission is normally centred on a single small volume, which appears to move about, but remains close to the tip. In the case of Tungsten with higher voltages or longer pulses the tip of the needle can heat up to incandescent temperatures. At higher voltages shock wave fronts appear to be observed as the vapour layer collapses at the end of the voltage pulse. Backlighting and no lighting to observe bubble/vapour layer formation and emission due to plasma formation were employed. Sometimes at higher voltages a thicker vapour layer engulfs the tip and no plasma emission/current is observed.

  14. Atmospheric pressure plasma produced inside a closed package by a dielectric barrier discharge in Ar/CO2 for bacterial inactivation of biological samples

    DEFF Research Database (Denmark)

    Chiper, Alina Silvia; Chen, Weifeng; Mejlholm, Ole

    2011-01-01

    The generation and evaluation of a dielectric barrier discharge produced inside a closed package made of a commercially available packaging film and filled with gas mixtures of Ar/CO2 at atmospheric pressure is reported. The discharge parameters were analysed by electrical measurements and optica...... times higher in the Ar/CO2 plasma compared with an Ar plasma. The efficiency of the produced plasma for the inactivation of bacteria on food inside the closed package was investigated....

  15. Influence of gas flow velocity on the transport of chemical species in an atmospheric pressure air plasma discharge

    Science.gov (United States)

    Hasan, M. I.; Walsh, J. L.

    2017-03-01

    This paper reports on a numerical study of the transport of reactive chemical species generated in an atmospheric-pressure air plasma discharge under the influence of a high velocity flowing gas. Using a 1D air plasma model, it is shown that the reactive species transported downstream of the discharge region can be categorized into three distinct groups based on their spatial distribution: (i) decaying downstream species, (ii) increasing downstream species and (iii) variable density species, where the density is a function of both spatial position and gas flow velocity. It is demonstrated that the gas flow velocity influences the dominant chemical reactions downstream of the discharge region, noticeably altering the composition of several key reactive chemical species transported to a given downstream location. As many emerging applications of atmospheric pressure plasma are driven by the flux of reactive chemical species, this study highlights the importance of gas flow velocity, not only as a means to enhance mass transport but also as a means to manipulate the very nature of the reactive plasma chemistry arriving at a given location.

  16. Surface Oxide Net Charge of a Titanium Alloy; Comparison Between Effects of Treatment With Heat or Radiofrequency Plasma Glow Discharge

    Science.gov (United States)

    MacDonald, Daniel E.; Rapuano, Bruce E.; Schniepp, Hannes C.

    2010-01-01

    In the current study, we have compared the effects of heat and radiofrequency plasma glow discharge (RFGD) treatment of a Ti6Al4V alloy on the physico-chemical properties of the alloy’s surface oxide. Titanium alloy (Ti6Al4V) disks were passivated alone, heated to 600 °C, or RFGD plasma treated in pure oxygen. RFGD treatment did not alter the roughness, topography, elemental composition or thickness of the alloy’s surface oxide layer. In contrast, heat treatment altered oxide topography by creating a pattern of oxide elevations approximately 50–100 nm in diameter. These nanostructures exhibited a three-fold increase in roughness compared to untreated surfaces when RMS roughness was calculated after applying a spatial high-pass filter with a 200 nm cutoff wavelength. Heat treatment also produced a surface enrichment in aluminum and vanadium oxides. Both RFGD and heat treatment produced similar increases in oxide wettability. Atomic force microscopy (AFM) measurements of metal surface oxide net charge signified by a long range force of attraction to or repulsion from a (negatively charged) silicon nitride AFM probe were also obtained for all three experimental groups. Force measurements showed that the RFGD-treated Ti6Al4V samples demonstrated a higher net positive surface charge at pH values below 6 and a higher net negative surface charge at physiological pH (pH values between 7 and 8) compared to control and heat-treated samples These findings suggest that RFGD treatment of metallic implant materials can be used to study the role of negatively charged surface oxide functional groups in protein bioactivity, osteogenic cell behavior and osseointegration independently of oxide topography. PMID:20880672

  17. SOC Estimation of Power Battery Design on Constant-current Discharge

    Directory of Open Access Journals (Sweden)

    Zeng Zhigang

    2014-04-01

    Full Text Available This paper takes the electric car’s power battery (VRLA battery cell as the research object, for real-time monitoring problem of power battery's state of charge (SOC and remaining time, The system adopts micro control unit (MCU 89S51 and AD974 to control battery discharge in constant current, Through the measurement of a periodic, get Series of working voltage, using phase-slope calculation method at this time calculating the battery's SOC and remaining time. Through the experiment, this estimation method proved the feasibility of the dynamic working point can be mapped to the static working point, and the largest relative error is no more than 7 %. For further improving the measurement accuracy and reducing error, Through the software can realize appropriate correction and compensation of temperature, aging and other interference factors. Error analysis results show that this method has small error, high measurement accuracy.

  18. Novel design of high voltage pulse source for efficient dielectric barrier discharge generation by using silicon diodes for alternating current.

    Science.gov (United States)

    Truong, Hoa Thi; Hayashi, Misaki; Uesugi, Yoshihiko; Tanaka, Yasunori; Ishijima, Tatsuo

    2017-06-01

    This work focuses on design, construction, and optimization of configuration of a novel high voltage pulse power source for large-scale dielectric barrier discharge (DBD) generation. The pulses were generated by using the high-speed switching characteristic of an inexpensive device called silicon diodes for alternating current and the self-terminated characteristic of DBD. The operation started to be powered by a primary DC low voltage power supply flexibly equipped with a commercial DC power supply, or a battery, or DC output of an independent photovoltaic system without transformer employment. This flexible connection to different types of primary power supply could provide a promising solution for the application of DBD, especially in the area without power grid connection. The simple modular structure, non-control requirement, transformer elimination, and a minimum number of levels in voltage conversion could lead to a reduction in size, weight, simple maintenance, low cost of installation, and high scalability of a DBD generator. The performance of this pulse source has been validated by a load of resistor. A good agreement between theoretically estimated and experimentally measured responses has been achieved. The pulse source has also been successfully applied for an efficient DBD plasma generation.

  19. Novel design of high voltage pulse source for efficient dielectric barrier discharge generation by using silicon diodes for alternating current

    Science.gov (United States)

    Truong, Hoa Thi; Hayashi, Misaki; Uesugi, Yoshihiko; Tanaka, Yasunori; Ishijima, Tatsuo

    2017-06-01

    This work focuses on design, construction, and optimization of configuration of a novel high voltage pulse power source for large-scale dielectric barrier discharge (DBD) generation. The pulses were generated by using the high-speed switching characteristic of an inexpensive device called silicon diodes for alternating current and the self-terminated characteristic of DBD. The operation started to be powered by a primary DC low voltage power supply flexibly equipped with a commercial DC power supply, or a battery, or DC output of an independent photovoltaic system without transformer employment. This flexible connection to different types of primary power supply could provide a promising solution for the application of DBD, especially in the area without power grid connection. The simple modular structure, non-control requirement, transformer elimination, and a minimum number of levels in voltage conversion could lead to a reduction in size, weight, simple maintenance, low cost of installation, and high scalability of a DBD generator. The performance of this pulse source has been validated by a load of resistor. A good agreement between theoretically estimated and experimentally measured responses has been achieved. The pulse source has also been successfully applied for an efficient DBD plasma generation.

  20. Kinetics of decolorization of azo dye by bipolar pulsed barrier discharge in a three-phase discharge plasma reactor

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Ruobing [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China)]. E-mail: zrbingdut@163.com; Zhang Chi [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Cheng Xingxin [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Wang Liming [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Wu Yan [Institute of Electrostatics and Special Power, Dalian University of Technology, Dalian 116024 (China); Guan Zhicheng [Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China)

    2007-04-02

    Removal of amaranth, a commercial synthetic azo dye widely used in the dye and food industry, was examined as a possible remediation technology for treating dye-contaminated water. Effects of various parameters such as gas flow rate, solution conductivity, pulse repetition frequency, etc., on decolorization kinetics were investigated. Experimental results show that an aqueous solution of 24 mg/l dye is 81.24% decolorized following 30 min plasma treatment for a 50 kV voltage and 0.75 m{sup 3}/h gas flow rate. Decolorization reaction of amaranth in the plasma reactor is a pseudo first order reaction. Rate constant (k) of decolorization increases quickly with increasing the applied voltage, pulse repetition frequency and the gas flow rate. However, when the applied voltage is beyond 50 kV and increases further, increase rate of k decreases. In addition, k decreases quickly when the solution conductivity increases from 200 to 1481 {mu}S/cm. The decolorization reaction has a high rate constant (k = 0.0269 min{sup -1}) when the solution pH is beyond 10. Rate constant k decreases with the decrease of pH and reaches minimum at a pH of about 5 (k {sub min} = 0.01603 min{sup -1}), then increases to 0.02105 min{sup -1} when pH decreases to 3.07. About 15% of the initial TOC can be degraded only in about 120 min non-thermal plasma treatment.

  1. Dependence of various SOL widths on plasma current and density in NSTX H-mode plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, J; Maingi, R; Boedo, J; Soukhanovskii, V A

    2009-02-12

    The dependence of various SOL widths on the line-averaged density ({ovr n}{sub e}) and plasma current (l{sub p}) for the quiescent H-mode plasmas with Type-V ELMs in the National Spherical Torus Experiment (NSTX) was investigated. It is found that the heat flux SOL width ({lambda}{sub q}), measured by the IR camera, is virtually insensitive to {ovr n}{sub e} and has a strong negative dependence on l{sub p}. This insensitivity of {lambda}{sub q} to {ovr n}{sub e} is consistent with the scaling law from JET H-mode plasmas that shows a very weak dependence on the upstream density. The electron temperature, ion saturation current density, electron density, and electron pressure decay lengths ({lambda}{sub Te}, {lambda}{sub jsat}, {lambda}{sub ne}, and {lambda}{sub pe}, respectively) measured by the probe showed that {lambda}{sub Te} and {lambda}{sub jsat} have strong negative dependence on l{sub p}, whereas {lambda}{sub ne} and {lambda}{sub pe} revealed only a little or no dependence. The dependence of {lambda}{sub Te} on l{sub p} is consistent with the scaling law in the literature while {lambda}{sub ne} and {lambda}{sub pe} dependence shows a different trend.

  2. The evolution of discharge current and channel radius in cloud-to-ground lightning return stroke process

    Science.gov (United States)

    Fan, Tingting; Yuan, Ping; Wang, Xuejuan; Cen, Jianyong; Chang, Xuan; Zhao, Yanyan

    2017-09-01

    The spectra of two negative cloud-to-ground lightning discharge processes with multi-return strokes are obtained by a slit-less high-speed spectrograph, which the temporal resolution is 110 μs. Combined with the synchronous electrical observation data and theoretical calculation, the physical characteristics during return strokes process are analysed. A positive correlation between discharge current and intensity of ionic lines in the spectra is verified, and based on this feature, the current evolution characteristics during four return strokes are investigated. The results show that the time from peak current to the half-peak value estimated by multi point-fitting is about 101 μs-139 μs. The Joule heat in per unit length of four return strokes channel is in the order of 105J/m-106 J/m. The radius of arc discharge channel is positively related to the discharge current, and the more intense the current is, the greater the radius of channel is. Furthermore, the evolution for radius of arc core channel in the process of return stroke is consistent with the change trend of discharge current after the peak value. Compared with the decay of the current, the temperature decreases more slowly.

  3. Calculation of the non-inductive current profile in high-performance NSTX plasmas

    Science.gov (United States)

    Gerhardt, S. P.; Fredrickson, E.; Gates, D.; Kaye, S.; Menard, J.; Bell, M. G.; Bell, R. E.; Le Blanc, B. P.; Kugel, H.; Sabbagh, S. A.; Yuh, H.

    2011-03-01

    The constituents of the current profile have been computed for a wide range of high-performance plasmas in NSTX (Ono et al 2000 Nucl. Fusion 40 557); these include cases designed to maximize the non-inductive fraction, pulse length, toroidal-β or stored energy. In the absence of low-frequency MHD activity, good agreement is found between the reconstructed current profile and that predicted by summing the independently calculated inductive, pressure-driven and neutral beam currents, without the need to invoke any anomalous beam ion diffusion. Exceptions occur, for instance, when there are toroidal Alfvén eigenmode avalanches or coupled m/n = 1/1 + 2/1 kink-tearing modes. In these cases, the addition of a spatially and temporally dependent fast-ion diffusivity can reduce the core beam current drive, restoring agreement between the reconstructed profile and the summed constituents, as well as bringing better agreement between the simulated and measured neutron emission rate. An upper bound on the fast-ion diffusivity of ~0.5-1 m2 s-1 is found in 'MHD-free' discharges, based on the neutron emission, the time rate of change in the neutron signal when a neutral beam is stepped and reconstructed on-axis current density.

  4. Effects and Mechanism of Atmospheric-Pressure Dielectric Barrier Discharge Cold Plasma on Lactate Dehydrogenase (LDH) Enzyme

    Science.gov (United States)

    Zhang, Hao; Xu, Zimu; Shen, Jie; Li, Xu; Ding, Lili; Ma, Jie; Lan, Yan; Xia, Weidong; Cheng, Cheng; Sun, Qiang; Zhang, Zelong; Chu, Paul K.

    2015-05-01

    Proteins are carriers of biological functions and the effects of atmospheric-pressure non-thermal plasmas on proteins are important to applications such as sterilization and plasma-induced apoptosis of cancer cells. Herein, we report our detailed investigation of the effects of helium-oxygen non-thermal dielectric barrier discharge (DBD) plasmas on the inactivation of lactate dehydrogenase (LDH) enzyme solutions. Circular dichroism (CD) and dynamic light scattering (DLS) indicate that the loss of activity stems from plasma-induced modification of the secondary molecular structure as well as polymerization of the peptide chains. Raising the treatment intensity leads to a reduced alpha-helix content, increase in the percentage of the beta-sheet regions and random sequence, as well as gradually decreasing LDH activity. However, the structure of the LDH plasma-treated for 300 seconds exhibits a recovery trend after storage for 24 h and its activity also increases slightly. By comparing direct and indirect plasma treatments, plasma-induced LDH inactivation can be attributed to reactive species (RS) in the plasma, especially ones with a long lifetime including hydrogen peroxide, ozone, and nitrate ion which play the major role in the alteration of the macromolecular structure and molecular diameter in lieu of heat, UV radiation, and charged particles.

  5. Statistical Analysis of Reducing Biochemical Oxygen Demand (BOD) on Industrial Rubber Wastewater using Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Syakur, Abdul; Zaman, Badrus; Yunita Nurmaliakasih, Dias

    2017-04-01

    Dielectric Barrier Discharge plasma (DBD) is one of type non-thermal plasma (non-equilibrium plasma) or can be referred to as cold plasma. In this research, DBD plasma be utilized to reduce organic compounds like Biochemichal oxygen demand in the wastewater rubber processing. In the environment field DBD plasma has been used as a treatment for reducing air pollutants such as gas COx, NOx and HC. In addition DBD plasma have been developed to processed wastewater as an alternative technology in wastewater treatment. DBD plasma appears when the electrode is given a high voltage so that, it will form electric field in the area of the electrodes which allows the ionization and the presence of high-energy electrons in the area. The presence of these electrons will ionize molecules of H2O into active species such as OH•, H• and H2O2. The active species that can oxidize into CO2 and H2O so, BOD that can be degraded. In this research for wastewater treatment used high voltage are 10kV, 11kV, 12kV and 13kV and variations of processing time for 5, 10, 15, 20, and 25 (minutes). By increasing the voltage and extend the contact time then the speed variation of electrons to ionize the greater and more active species to be formed to degrade the pollutants to the maximum. This research used quantitative analysis with statistical analysis using SPSS software.

  6. Analysis of plasma equilibrium based on orbit-driven current density profile in steady-state plasma on QUEST

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, K., E-mail: nakamura@triam.kyushu-u.ac.jp [RIAM, Kyushu University, Kasuga 816-8580 (Japan); Alam, M.M. [IGSES, Kyushu University, Kasuga 816-8580 (Japan); Jiang, Y.Z. [Tsinghua University, Beijing 100084 (China); Mitarai, O. [Tokai University, Kumamoto 862-8652 (Japan); Kurihara, K.; Kawamata, Y.; Sueoka, M.; Takechi, M. [Japan Atomic Energy Agency, Naka 311-0193 (Japan); Hasegawa, M.; Tokunaga, K.; Araki, K.; Zushi, H.; Hanada, K.; Fujisawa, A.; Idei, H.; Nagashima, Y.; Kawasaki, S.; Nakashima, H.; Higashijima, A.; Nagata, T. [RIAM, Kyushu University, Kasuga 816-8580 (Japan); and others

    2016-11-01

    Highlights: • High energy particle guiding center orbit is calculated as a contour plot of conserved variable. • Current density profile is analyzed based on the orbit-driven current. • Plasma equilibrium is reconstructed by considering the hollow current profile. - Abstract: In the present RF-driven (ECCD) steady-state plasma on QUEST (B{sub t} = 0.25 T, R = 0.68 m, a = 0.40 m), plasma current seems to flow in the open magnetic surface outside of the closed magnetic surface in the low-field region according to plasma current fitting (PCF) method. We consider that the current in the open magnetic surface is due to orbit-driven current by high-energy particles in RF-driven plasma. So based on the analysis of current density profile based on the orbit-driven current, plasma equilibrium is to be calculated. We calculated high energy particles guiding center orbits as a contour plot of conserved variable in Hamiltonian formulation and considered particles initial position with different levels of energy and pitch angles that satisfy resonance condition. Then the profile of orbit-driven current is estimated by multiplying the particle density on the resonance surface and the velocity on the orbits. This analysis shows negative current near the magnetic axis and hollow current profile is expected even if pressure driven current is considered. Considering the hollow current profile shifted toward the low-field region, the equilibrium is fitted by J-EFIT coded by MATLAB.

  7. Determination of the plasma impedance of a glow discharge in carbon dioxide

    Science.gov (United States)

    Kiselev, A. S.; Smirnov, E. A.

    2017-07-01

    In this work an expression for the dynamic resistance of a glow discharge flowing in long tubes is obtained and analyzed. The expression describes the physical processes occurring in the positive column of a glow discharge. The frequency dependences of the active and reactive components as well as the dynamic resistance module for the discharge conditions corresponding to CO2-lasers have been calculated. Based on the simulation results developed a computer program in the C# programming language for modeling the dynamic resistance discharge of glow discharge lasers.

  8. Effect of limiter currents on plasma equilibrium and stability in a tokamak

    Science.gov (United States)

    Belashov, V. I.; Gribov, Yu. V.; Putvinskij, S. V.; Brevnov, N. N.

    The results of theoretical and experimental research of currents between diaphragms limiting plasma cord in tokamak on plasma equilibrium and stability with an arbitrary form of transverse cross section are presented. It is shown that plasma cord behaviour depends on applied voltage polarity. The phenomena considered can be important for tokamaks in which fast plasma compression in a big radius is invisaged.

  9. Modification of polylactic acid surface using RF plasma discharge with sputter deposition of a hydroxyapatite target for increased biocompatibility

    Energy Technology Data Exchange (ETDEWEB)

    Tverdokhlebov, S.I., E-mail: tverd@tpu.ru [Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk 634050 (Russian Federation); Bolbasov, E.N.; Shesterikov, E.V. [Tomsk Polytechnic University, 30 Lenin Avenue, Tomsk 634050 (Russian Federation); Antonova, L.V.; Golovkin, A.S.; Matveeva, V.G. [Federal State Budgetary Institution Research Institute for Complex Issues of Cardiovascular Disease, 6 Sosnovy Blvd, Kemerovo 650002 (Russian Federation); Petlin, D.G.; Anissimov, Y.G. [Griffith University, School of Natural Sciences, Engineering Dr., Southport, QLD 4222 (Australia)

    2015-02-28

    Highlights: • The treatment by plasma of radio-frequency magnetron discharge with hydroxyapatite target sputtering improves the biocompatibility of PLLA surface. • The treatment significantly increases the roughness of PLLA surface. • The formation of rough highly porous surface is due to the etching and crystallization processes on PLLA surface during treatment. • Maximum concentration of the ions from the sputtered target is achieved at 60 s of the plasma treatment. - Abstract: Surface modification of polylactic acid (PLLA) by plasma of radio-frequency magnetron discharge with hydroxyapatite target sputtering was investigated. Increased biocompatibility was demonstrated using studies with bone marrow multipotent mesenchymal stromal cells. Atomic force microscopy demonstrates that the plasma treatment modifies the surface morphology of PLLA to produce rougher surface. Infrared spectroscopy and X-ray diffraction revealed that changes in the surface morphology are caused by the processes of PLLA crystallization. Fluorescent X-ray spectroscopy showed that the plasma treatment also changes the chemical composition of PLLA, enriching it with ions of the sputtered target: calcium, phosphorus and oxygen. It is hypothesized that these surface modifications increase biocompatibility of PLLA without increasing toxicity.

  10. PTFE surface etching in the post-discharge of a RF scanning plasma torch: evidence of ejected fluorinated species

    CERN Document Server

    Dufour, Thierry; Viville, Pascal; Duluard, Corinne Y; Desbief, Simon; Lazzaroni, Roberto; Reniers, François

    2016-01-01

    The texturization of poly(tetrafluoroethylene) (PTFE) surfaces is achieved at atmospheric pressure by using the post-discharge of a radio-frequency plasma torch supplied in helium and oxygen gases. The surface properties are characterized by contact angle measurement, X-ray photoelectron spectroscopy and atomic force microscopy. We show that the plasma treatment increases the surface hydrophobicity (with water contact angles increasing from 115 to 155{\\deg}) only by modifying the PTFE surface morphology and not the stoichiometry. Measurements of sample mass losses correlated to the ejection of CF$_2$ fragments from the PTFE surface evidenced an etching mechanism at atmospheric pressure.

  11. Order–chaos–order–chaos transition and evolution of multiple anodic double layers in glow discharge plasma

    Directory of Open Access Journals (Sweden)

    Prince Alex

    2015-01-01

    Full Text Available Plasma often shows complex dynamic behavior. We present an experimental observation of order–chaos–order–chaos transition in glow discharge plasma. These transitions correspond to the evolution of different stages of a multiple anodic double layer. Multiple anodic double layers were produced in a typical glow discharge condition and associated floating potential oscillations were recorded for monotonous variation of one of the control parameters i.e. the cathode voltage. With a variation in the cathode voltage, the multiple anodic double layers were evolved to different stages. The recorded experimental time series data had been analyzed and quantified using power spectra, phase space trajectories, time-delay reconstructions of state space, Lyapunov exponent and correlation dimensions. The analysis shows that the chaotic behavior corresponds to diffused boundaries between two double layers.

  12. Two-dimensional MHD simulation of the plasma focus discharge, taking the neutral gas into account as a third medium. Zweidimensionale MHD-Simulation der Plasmafokusentladung unter Beruecksichtigung des Neutralgases als dritte Fluessigkeit

    Energy Technology Data Exchange (ETDEWEB)

    Behler, K.

    1984-01-01

    Planned as a plasma accelerator for filling other fusion devices, the plasma focus with its special properties became an original and remarkable type of experiment. The plasma discharge ignited in the coaxial electrodes over an electric insulator propagates, driven by its own magnetic field, towards the end of the electrodes. Leaving the channel most of the accelerated plasma is shot into space. The electric current layer over the end of the inner electrode collapses and at last forms a hot, dense plasmafilament on the axis. With deuterium as a fuel gas, intense neutron emission is observed, which makes this 'plasma focus' interesting as an effective fusion plasma. (orig./AH).

  13. A comparison of reactive plasma pre-treatments on PET substrates by Cu and Ti pulsed-DC and HIPIMS discharges

    Energy Technology Data Exchange (ETDEWEB)

    Audronis, M., E-mail: m.audronis@yahoo.co.uk [Gencoa Ltd, Physics Road, Speke, Liverpool, L24 9HP (United Kingdom); Hinder, S.J. [The Surface Analysis Laboratory, Faculty of Engineering and Physical Sciences, University of Surrey, Guildford, GU2 7XH (United Kingdom); Mack, P. [ThermoFisher Scientific Ltd, Imberhorne Lane, East Grinstead, Sussex, RH19 1UB (United Kingdom); Bellido-Gonzalez, V. [Gencoa Ltd, Physics Road, Speke, Liverpool, L24 9HP (United Kingdom); Bussey, D.; Matthews, A. [Department of Engineering Materials, University of Sheffield, Sheffield S1 3JD (United Kingdom); Baker, M.A. [The Surface Analysis Laboratory, Faculty of Engineering and Physical Sciences, University of Surrey, Guildford, GU2 7XH (United Kingdom)

    2011-12-30

    PET web samples have been treated by magnetically enhanced glow discharges powered using either medium frequency pulse direct current (p-DC) or low frequency high power pulse (HIPIMS) sources. The plasma pre-treatment processes were carried out in an Ar-O{sub 2} atmosphere using either Cu or Ti sputter targets. XPS, AFM and sessile drop water contact angle measurements have been employed to examine changes in surface chemistry and morphology for different pre-treatment process parameters. Deposition of metal oxide onto the PET surface is observed as a result of the sputter magnetron-based glow discharge web treatment. Using the Cu target, both the p-DC and HIPIMS processes result in the formation of a thin CuO layer (with a thickness between 1 and 11 nm) being deposited onto the PET surface. Employing the Ti target, both p-DC and HIPIMS processes give rise to a much lower concentration of Ti (< 5 at.%), in the form of TiO{sub 2} on the PET treated surface. The TiO{sub 2} is probably distributed as an island-like distribution covering the PET surface. Presence of Cu and Ti oxide constituents on the treated PET is beneficial in aiding the adhesion but alone (i.e. without oxygen plasma activation) is not enough to provide very high levels of hydrophilicity as is clear from sessile drop water contact angle measurements on aged samples. Exposure to the plasma treatments leads to a small amount of roughening of the substrate surface, but the average surface roughness in all cases is below 2.5 nm. The PET structure at the interface with a coating is mostly or wholly preserved. The oxygen plasma treatment, metal oxide deposition and surface roughening resulting from the HIPIMS and p-DC treatments will promote adhesion to any subsequent thin film that is deposited immediately following the plasma treatment.

  14. Formation of current filaments and magnetic field generation in a quantum current-carrying plasma

    Science.gov (United States)

    Niknam, A. R.; Taghadosi, M. R.; Majedi, S.; Khorashadizadeh, S. M.

    2013-09-01

    The nonlinear dynamics of filamentation instability and magnetic field in a current-carrying plasma is investigated in the presence of quantum effects using the quantum hydrodynamic model. A new nonlinear partial differential equation is obtained for the spatiotemporal evolution of the magnetic field in the diffusion regime. This equation is solved by applying the Adomian decomposition method, and then the profiles of magnetic field and electron density are plotted. It is shown that the saturation time of filamentation instability increases and, consequently, the instability growth rate and the magnetic field amplitude decrease in the presence of quantum effects.

  15. Heat and Radiofrequency Plasma Glow Discharge Pretreatment of a Titanium Alloy: Eveidence for Enhanced Osteoinductive Properties

    Science.gov (United States)

    Rapuano, Bruce E.; Singh, Herman; Boskey, Adele L.; Doty, Stephen B.; MacDonald, Daniel E.

    2013-01-01

    It is believed that orthopedic and implant longevity can be improved by optimizing fixation, or direct bone-implant contact, through the stimulation of new bone formation around the implant. The purpose of this study was to determine whether heat (600°C) or radiofrequency plasma glow discharge (RFGD) pretreatment of Ti6Al4V stimulated calcium-phosphate mineral formation in cultures of attached MC3T3 osteoprogenitor cells with or without a fibronectin coating. Calcium-phosphate mineral was analyzed by flame atomic absorption spectrophotometry, scanning electron microscopy (SEM)/electron dispersive X-ray microanalysis (EDAX) and Fourier transformed infrared spectroscopy (FTIR). RFGD and heat pretreatments produced a general pattern of increased total soluble calcium levels, although the effect of heat pretreatment was greater than that of RFGD. SEM/EDAX showed the presence of calcium-and phosphorus-containing particles on untreated and treated disks that were more numerous on fibronectin-coated disks. These particles were observed earliest (1 week) on RFGD-pretreated surfaces. FTIR analyses showed that the heat pretreatment produced a general pattern of increased levels of apatite mineral at 2–4 weeks; a greater effect was observed for fibronectin-coated disks compared to uncoated disks. The observed findings suggest that heat pretreatment of Ti6Al4V increased the total mass of the mineral formed in MC3T3 osteoprogenitor cell cultures more than RFGD while the latter pretreatment hastened the early deposition of mineral. These findings help to support the hypothesis that the pretreatments enhance the osteoinductive properties of the alloy. PMID:23494951

  16. Hydrazine-enhanced NO conversion in a pulsed corona discharge plasma (PCDP reactor: Behaviors and mechanism

    Directory of Open Access Journals (Sweden)

    Liu Hong

    2016-09-01

    Full Text Available The NO conversion efficiency in a pulsed corona discharge plasma (PCDP reactor in the presence of a new additive, hydrazine hydrate (N2H4·H2O, was studied, and the reaction mechanism was analyzed. The NO conversion efficiency reached 62.5%, and the NO conversion Energy Yield (EY reached 20.9 gNO/kWh, which is higher than that obtained using water or ammonia additives under the same conditions. The predominant elementary reactions and radicals, as well as the mechanism by which the additive enhanced the NO conversion process, were determined by comparing experimental data with theoretical simulation results and by performing a sensitivity analysis. After the addition of N2H4·H2O, the N2H4 reacts with radicals generated in the PCDP reactor to form a large quantity of strongly reducing species with NH2 as the predominant component, which can directly reduce NO to N2 and effectively prevent the generation of N2O. Compared with the traditional PCDP-based De-NOx process in which nitric acid is generated by oxidation with an additional neutralization step required, this new PCDP-based De-NOx process with N2H4·H2O addition is superior because NO is mostly reduced to N2. The study provides a basis for the application of N2H4·H2O as a synergist to improve NO abatement in a PCDP reactor.

  17. Interferometric and schlieren characterization of the plasmas and shock wave dynamics during laser-triggered discharge in atmospheric air

    Energy Technology Data Exchange (ETDEWEB)

    Wei, Wenfu; Li, Xingwen, E-mail: xwli@mail.xjtu.edu.cn; Wu, Jian; Yang, Zefeng; Jia, Shenli; Qiu, Aici [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Shaanxi 710049 (China)

    2014-08-15

    This paper describes our efforts to reveal the underlying physics of laser-triggered discharges in atmospheric air using a Mach-Zehnder interferometer and schlieren photography. Unlike the hemispherical shock waves that are produced by laser ablation, bell-like morphologies are observed during laser-triggered discharges. Phase shifts are recovered from the interferograms at a time of 1000 ns by the 2D fast Fourier transform method, and then the values of the refractive index are deduced using the Abel inversion. An abundance of free electrons is expected near the cathode surface. The schlieren photographs visualize the formation of stagnation layers at ∼600 ns in the interaction zones of the laser- and discharge-produced plasmas. Multiple reflected waves are observed at later times with the development of shock wave propagations. Estimations using the Taylor-Sedov self-similar solution indicated that approximately 45.8% and 51.9% of the laser and electrical energies are transferred into the gas flow motions, respectively. Finally, numerical simulations were performed, which successfully reproduced the main features of the experimental observations, and provided valuable insights into the plasma and shock wave dynamics during the laser-triggered discharge.

  18. Investigation of the effect of dielectric barrier discharge plasma actuators on the radar cross section of an object

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, S; Arjomandi, M [University of Adelaide, Adelaide, South Australia, 5005 (Australia)

    2011-08-10

    The application of dielectric barrier discharge (DBD) plasma as an electromagnetic absorber was investigated by determining the radar cross section (RCS) of a rectangular, flat plate with a DBD plasma actuator array installed on one of its sides. In order to justify the experimental results, the expected effect of plasma actuation on RCS was analysed by determining the attenuation effect of the plasma with the Lorentz model. Due to the very limited life time of the free electrons and the small extent of the plasma sheath, the attenuation was found to be only minimal. The theoretical results have been verified by comparing the measured RCS values of a plate with and without plasma actuation applied on it in a high-frequency anechoic lab. As expected, no significant influence of DBD plasma on RCS was detected. In addition, it was found that the high voltage power supply used as a part of DBD circuitry produced a high level of disturbance even in the microwave range.

  19. Comparison of bottom-track to global positioning system referenced discharges measured using an acoustic Doppler current profiler

    Science.gov (United States)

    Wagner, Chad R.; Mueller, David S.

    2011-01-01

    A negative bias in discharge measurements made with an acoustic Doppler current profiler (ADCP) can be caused by the movement of sediment on or near the streambed. The integration of a global positioning system (GPS) to track the movement of the ADCP can be used to avoid the systematic negative bias associated with a moving streambed. More than 500 discharge transects from 63 discharge measurements with GPS data were collected at sites throughout the US, Canada, and New Zealand with no moving bed to compare GPS and bottom-track-referenced discharges. Although the data indicated some statistical bias depending on site conditions and type of GPS data used, these biases were typically about 0.5% or less. An assessment of differential correction sources was limited by a lack of data collected in a range of different correction sources and different GPS receivers at the same sites. Despite this limitation, the data indicate that the use of Wide Area Augmentation System (WAAS) corrected positional data is acceptable for discharge measurements using GGA as the boat-velocity reference. The discharge data based on GPS-referenced boat velocities from the VTG data string, which does not require differential correction, were comparable to the discharges based on GPS-referenced boat velocities from the differentially-corrected GGA data string. Spatial variability of measure discharges referenced to GGA, VTG and bottom-tracking is higher near the channel banks. The spatial variability of VTG-referenced discharges is correlated with the spatial distribution of maximum Horizontal Dilution of Precision (HDOP) values and the spatial variability of GGA-referenced discharges is correlated with proximity to channel banks.

  20. Treatment surfaces with atomic oxygen excited in dielectric barrier discharge plasma of O2 admixed to N2

    Directory of Open Access Journals (Sweden)

    E. V. Shun'ko

    2012-06-01

    Full Text Available This paper describes the increase in surface energy of substrates by their treatment with gas composition generated in plasmas of DBD (Dielectric Barrier Discharge in O2 admixed with N2. Operating gas dissociation and excitation was occurred in plasmas developed in two types of reactors of capacitively-coupled dielectric barrier configurations: coaxial cylindrical, and flat rectangular. The coaxial cylindrical type comprised an inner cylindrical electrode encapsulated in a ceramic sheath installed coaxially inside a cylindrical ceramic (quartz tube passing through an annular outer electrode. Components of the flat rectangular type were a flat ceramic tube of a narrow rectangular cross section supplied with two flat electrodes mounted against one another outside of the long parallel walls of this tube. The operating gas, mixture of N2 and O2, was flowing in a completely insulated discharge gap formed between insulated electrodes of the devices with an average velocity of gas inlet of about 7 to 9 m/s. Dielectric barrier discharge plasma was excited in the operating gaps with a bipolar pulse voltage of about 6 kV for 2 ms at 50 kHz repetition rate applied to the electrodes of the coaxial device, and of about 14 kV for 7 ms at 30 kHz repetition rate for the flat linear device. A lifetime of excited to the 2s22p4(1S0 state in DBD plasma and streaming to the surfaces with a gas flow atomic oxygen, responsible presumably for treating surfaces, exceeded 10 ms in certain cases, that simplified its separation from DBD plasma and delivery to substrates. As it was found in particular, surfaces of glass and some of polymers revealed significant enhancement in wettability after treatment.

  1. Sterilization/disinfection using reduced-pressure plasmas: some differences between direct exposure of bacterial spores to a discharge and their exposure to a flowing afterglow

    Science.gov (United States)

    Moisan, M.; Levif, P.; Séguin, J.; Barbeau, J.

    2014-07-01

    The use of plasma for sterilization or disinfection offers a promising alternative to conventional steam or chemical approaches. Plasma can operate at temperatures less damaging to some heat-sensitive medical devices and, in contrast to chemicals, can be non-toxic and non-polluting for the operator and the environment, respectively. Direct exposure to the gaseous discharge (comprising an electric field and ions/electrons) or exposure to its afterglow (no E-field) can both be envisaged a priori, since these two methods can achieve sterility. However, important issues must be considered besides the sterility goal. Direct exposure to the discharge, although yielding a faster inactivation of microorganisms, is shown to be potentially more aggressive to materials and sometimes subjected to the shadowing effect that precludes the sterilization of complex-form items. These two drawbacks can be successfully minimized with an adequate flowing-afterglow exposure. Most importantly, the current paper shows that direct exposure to the discharge can lead to the dislodgment and release of viable microorganisms from their substratum. Such a phenomenon could be responsible for the recontamination of sterilized devices as well as possible contamination of the ambient surroundings, additionally yielding an erroneous over-appreciation of the inactivation efficiency. The operation of the N2-O2 flowing afterglow system being developed in our group is such that there are no ions and electrons left in the process chamber (late-afterglow regime) in full contrast with their presence in the discharge. The dislodgment and release of spores could be attributed, based on the literature, to their electrostatic charging by electrons, leading to an (outward) electrostatic stress that exceeds the adhesion of the spores on their substrate.

  2. Potential of electric discharge plasma methods in abatement of volatile organic compounds originating from the food industry.

    Science.gov (United States)

    Preis, S; Klauson, D; Gregor, A

    2013-01-15

    Increased volatile organic compounds emissions and commensurate tightening of applicable legislation mean that the development and application of effective, cost-efficient abatement methods are areas of growing concern. This paper reviews the last two decades' publications on organic vapour emissions from food processing, their sources, impacts and treatment methods. An overview of the latest developments in conventional air treatment methods is presented, followed by the main focus of the paper, non-thermal plasma technology. The results of the review suggest that non-thermal plasma technology, in its pulsed corona discharge configuration, is an emerging treatment method with potential for low-cost, effective abatement of a wide spectrum of organic air pollutants. It is found that the combination of plasma treatment with catalysis is a development trend that demonstrates considerable potential. The as yet relatively small number of plasma treatment applications is considered to be due to the novelty of pulsed electric discharge techniques and a lack of reliable pulse generators and reactors. Other issues acting as barriers to widespread adoption of the technique include the possible formation of stable oxidation by-products, residual ozone and nitrogen oxides, and sensitivity towards air humidity. Copyright © 2012 Elsevier Ltd. All rights reserved.

  3. Preferential killing of human lung cancer cell lines with mitochondrial dysfunction by nonthermal dielectric barrier discharge plasma

    Science.gov (United States)

    Panngom, K; Baik, K Y; Nam, M K; Han, J H; Rhim, H; Choi, E H

    2013-01-01

    The distinctive cellular and mitochondrial dysfunctions of two human lung cancer cell lines (H460 and HCC1588) from two human lung normal cell lines (MRC5 and L132) have been studied by dielectric barrier discharge (DBD) plasma treatment. This cytotoxicity is exposure time-dependent, which is strongly mediated by the large amount of H2O2 and NOx in culture media generated by DBD nonthermal plasma. It is found that the cell number of lung cancer cells has been reduced more than that of the lung normal cells. The mitochondrial vulnerability to reactive species in H460 may induce distinctively selective responses. Differential mitochondrial membrane potential decrease, mitochondrial enzymatic dysfunction, and mitochondrial morphological alteration are exhibited in two cell lines. These results suggest the nonthermal plasma treatment as an efficacious modality in lung cancer therapy. PMID:23703387

  4. Microsecond-pulsed dielectric barrier discharge plasma stimulation of tissue macrophages for treatment of peripheral vascular disease

    Energy Technology Data Exchange (ETDEWEB)

    Miller, V., E-mail: vmiller@coe.drexel.edu; Lin, A.; Brettschneider, J.; Fridman, G.; Fridman, A. [AJ Drexel Plasma Institute, Drexel University, Camden, New Jersey 08103 (United States); Kako, F.; Gabunia, K.; Kelemen, S.; Autieri, M. [Department of Physiology, Independence Blue Cross Cardiovascular Research Center, Temple University School of Medicine, Philadelphia, Pennsylvania 19140 (United States)

    2015-12-15

    Angiogenesis is the formation of new blood vessels from pre-existing vessels and normally occurs during the process of inflammatory reactions, wound healing, tissue repair, and restoration of blood flow after injury or insult. Stimulation of angiogenesis is a promising and an important step in the treatment of peripheral artery disease. Reactive oxygen species have been shown to be involved in stimulation of this process. For this reason, we have developed and validated a non-equilibrium atmospheric temperature and pressure short-pulsed dielectric barrier discharge plasma system, which can non-destructively generate reactive oxygen species and other active species at the surface of the tissue being treated. We show that this plasma treatment stimulates the production of vascular endothelial growth factor, matrix metalloproteinase-9, and CXCL 1 that in turn induces angiogenesis in mouse aortic rings in vitro. This effect may be mediated by the direct effect of plasma generated reactive oxygen species on tissue.

  5. Simulation of precipitation and discharge extremes of the river Meuse in current and future climate

    NARCIS (Netherlands)

    Leander, R.

    2009-01-01

    The river Meuse is the second largest river in the Netherlands and is characterized by strong variations in its discharge. From a government point of view there is a particular interest in discharge levels with return periods in the order of 1000 years, far beyond the length of the observed

  6. Discharge dynamics and plasma density recovery by on/off switches of additional gas

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Hyo-Chang, E-mail: lhc@kriss.re.kr [Center for Vacuum Technology, Korea Research Institute of Standard and Science, Daejeon 305-340 (Korea, Republic of); Department of Electrical Engineering, Hanyang University, 222 Wangsimni-ro, Seongdong-gu, Seoul 04763 (Korea, Republic of); Kwon, Deuk-Chul [Plasma Technology Research Center, Nation Fusion Research Institute, Gunsan 573-540 (Korea, Republic of); Oh, SeungJu; Kang, Hyun-Ju; Kim, Yu-Sin; Chung, Chin-Wook, E-mail: joykang@hanyang.ac.kr [Department of Electrical Engineering, Hanyang University, 222 Wangsimni-ro, Seongdong-gu, Seoul 04763 (Korea, Republic of)

    2016-06-15

    Measurement of the plasma density is investigated to study plasma dynamics by adding reactive gas (O{sub 2}) or rare gas (He) in Ar plasmas. When the O{sub 2} or He gas is added, plasma density is suddenly decreased, while the plasma density recovers slowly with gas off. It is found that the recovery time is strongly dependent on the gas flow rate, and it can be explained by effect of gas residence time. When the He gas is off in the Ar plasma, the plasma density is overshot compared to the case of the O{sub 2} gas pulsing due to enhanced ionizations by metastable atoms. Analysis and calculation for correlation between the plasma density dynamics and the gas pulsing are also presented in detail.

  7. The Double Star Plasma Electron and Current Experiment

    Directory of Open Access Journals (Sweden)

    A. N. Fazakerley

    2005-11-01

    Full Text Available The Double Star Project is a collaboration between Chinese and European space agencies, in which two Chinese magnetospheric research spacecraft, carrying Chinese and European instruments, have been launched into equatorial (on 29 December 2003 and polar (on 25 July 2004 orbits designed to enable complementary studies with the Cluster spacecraft. The two Double Star spacecraft TC-1 and TC-2 each carry a Double Star Plasma Electron and Current Experiment (PEACE instrument. These two instruments were based on Cluster Flight Spare equipment, but differ from Cluster instruments in two important respects. Firstly, a Double Star PEACE instrument has only a single sensor, which must be operated in a manner not originally envisaged in the Cluster context in order to sample the full range of energies. Secondly, the DPU hardware was modified and major changes of onboard software were implemented, most notably a completely different approach to data compression has been adopted for Double Star, which allows high resolution 3-dimensional distributions to be transmitted almost every spin, a significant improvement over Cluster. This paper describes these instruments, and includes examples of data collected in various magnetospheric regions encountered by the spacecraft which have been chosen to illustrate the power of combined Double Star and Cluster measurements.

  8. OH and O radicals production in atmospheric pressure air/Ar/H2O gliding arc discharge plasma jet

    Science.gov (United States)

    N, C. ROY; M, R. TALUKDER; A, N. CHOWDHURY

    2017-12-01

    Atmospheric pressure air/Ar/H2O gliding arc discharge plasma is produced by a pulsed dc power supply. An optical emission spectroscopic (OES) diagnostic technique is used for the characterization of plasmas and for identifications of {{OH}} and {{O}} radicals along with other species in the plasmas. The OES diagnostic technique reveals the excitation T x ≈ 5550–9000 K, rotational T r ≈ 1350–2700 K and gas T g ≈ 850–1600 K temperatures, and electron density {n}{{e}}≈ ({1.1-1.9})× {10}14 {{{cm}}}-3 under different experimental conditions. The production and destruction of {{OH}} and {{O}} radicals are investigated as functions of applied voltage and air flow rate. Relative intensities of {{OH}} and {{O}} radicals indicate that their production rates are increased with increasing {{Ar}} content in the gas mixture and applied voltage. {n}{{e}} reveals that the higher densities of {{OH}} and {{O}} radicals are produced in the discharge due to more effective electron impact dissociation of {{{H}}}2{{O}} and {{{O}}}2 molecules caused by higher kinetic energies as gained by electrons from the enhanced electric field as well as by enhanced {n}{{e}}. The productions of {{OH}} and {{O}} are decreasing with increasing air flow rate due to removal of Joule heat from the discharge region but enhanced air flow rate significantly modifies discharge maintenance properties. Besides, {T}{{g}} significantly reduces with the enhanced air flow rate. This investigation reveals that {{Ar}} plays a significant role in the production of {{OH}} and {{O}} radicals.

  9. Electro-Catalysis System for Biodiesel Synthesis from Palm Oil over Dielectric-Barrier Discharge Plasma Reactor

    Directory of Open Access Journals (Sweden)

    Istadi Istadi

    2014-07-01

    Full Text Available Biodiesel synthesis reaction routes from palm oil using plasma electro-catalysis process over Dielectric-Barrier Discharge (DBD plasma reactor were studied. The study was focused on finding possible reaction mechanism route during plasma electro-catalysis process. The prediction was performed based on the changes of Gas Chromatography Mass Spectrometer (GC-MS and Fourier Transform Infra Red (FT-IR analyses to the biodiesel products with respect to time length of plasma treatment. It was found that main reaction mechanism occurred in the plasma electro-catalysis system was non-thermal pyrolysis rather than transesterification. The main reactions within the plasma treatment were due to collision between high energetic electrons (supplied from high voltage power supply through high voltage electrode and the reaction mixtures. The high energetic electrons affected the electrons pair of covalent bonding to be excited or dissociated even ionized at higher energy. Therefore, this plasma electro-catalysis system was promising for biodiesel synthesis from vegetable oils due to only very short time reaction was needed, even no need a catalyst, no soap formation, and no glycerol by-product. This system could produce fatty acid methyl ester yield of 75.65% at 120 seconds and other possible chemicals, such as alkynes, alkanes, esters, carboxylic acid, and aldehydes. However, during the plasma process, the reaction mechanisms were still difficult to be controlled due the action of available high energetic electrons. The advanced studies on how to control the reaction mechanism selectively in the plasma electro-catalysis will be published elsewhere. © 2014 BCREC UNDIP. All rights reservedReceived: 23rd January 2014; Revised: 20th March 2014; Accepted: 23rd March 2014[How to Cite: Istadi, I., Yudhistira, A.D., Anggoro, D.D., Buchori, L. (2014. Electro-Catalysis System for Biodiesel Synthesis from Palm Oil over Dielectric-Barrier Discharge Plasma Reactor

  10. Effects of glow discharge cleanings on hydrogen isotope removal for plasma facing materials

    Energy Technology Data Exchange (ETDEWEB)

    Yamauchi, Y., E-mail: yamauchi@qe.eng.hokudai.ac.jp [Faculty of Engineering, Hokkaido University, Kita-13, Nishi-8, Kita-ku, Sapporo, Hokkaido 060-8628 (Japan); Matsumoto, A.; Kosaka, Y.; Kimura, Y.; Takeda, K. [Graduate School of Engineering, Hokkaido University, Kita-13, Nishi-8, Kita-ku, Sapporo, Hokkaido 060-8628 (Japan); Hino, T.; Nobuta, Y. [Faculty of Engineering, Hokkaido University, Kita-13, Nishi-8, Kita-ku, Sapporo, Hokkaido 060-8628 (Japan); Nishimura, K. [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki, Gifu 509-5292 (Japan); Ueda, Y. [Graduate School of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan)

    2013-07-15

    The effect of the discharge cleanings on hydrogen isotope removal have been evaluated for graphite, stainless steel, tungsten, boron and titanium. For all materials, the helium glow discharge cleaning was the most effective on the hydrogen isotope removal among the inert gas discharges. High efficiency of energy transfer to target atom and deep projected range for helium ion might be responsible for the high removal fraction. The effect of argon glow discharge cleaning was small. The small removal fraction for the argon might be owing to re-deposition layer, which acted as a screening to the removal. The hydrogen isotope in the tungsten was hardly removed by the inert gas discharge cleanings. The small removal fraction for the tungsten might be owing to hydrogen isotope retention in deeper regions resulting from diffusion along with the grain boundary or the porous structure. Surface impurity and morphologies significantly influenced the deuterium removal effects.

  11. Current discharge management of acute coronary syndromes: baseline results from a national quality improvement initiative.

    Science.gov (United States)

    Wai, A; Pulver, L K; Oliver, K; Thompson, A

    2012-05-01

    Evidence-practice gaps exist in the continuum of care for patients with acute coronary syndromes (ACS), particularly at hospital discharge. We aimed to describe the methodology and baseline results of the Discharge Management of Acute Coronary Syndromes (DMACS) project, focusing on the prescription of guideline-recommended medications, referral to cardiac rehabilitation and communication between the hospital, patient and their primary healthcare professionals. DMACS employed Drug Use Evaluation methodology involving data collection, evaluation and feedback, and targeted educational interventions. Adult patients with ACS discharged during a 4-month period were eligible to participate. Data were collected (maximum 50 patients) at each site through an inpatient medical record review, a general practitioner (GP) postal/fax survey conducted 14 days post discharge and a patient telephone survey 3 months post discharge. Forty-nine hospitals participated in the audit recruiting 1545 patients. At discharge, 57% of patients were prescribed a combination of antiplatelet agent(s), beta-blocker, statin and angiotensin-converting enzyme inhibitor and/or angiotensin II-antagonist. At 3 months post discharge, 48% of patients reported using the same combination. Some 67% of patients recalled being referred to cardiac rehabilitation; of these, 33% had completed the programme. In total, 83% of patients had a documented ACS management plan at discharge. Of these, 90% included a medication list, 56% a chest pain action plan and 54% risk factor modification advice. Overall, 65% of GPs rated the quality of information received in the discharge summary as 'very good' to 'excellent'. The findings of our baseline audit showed that despite the robust evidence base and availability of national guidelines, the management of patients with ACS can be improved. These findings will inform a multifaceted intervention strategy to improve adherence to guidelines for the discharge management of

  12. Plasma density scaling at the current reversal in the STOR-1M tokamak with AC operation

    Science.gov (United States)

    Mitarai, Osamu; Hirose, Akira; Skarsgard, Harvey M.

    1992-02-01

    Plasma density behavior in the STOR-1M tokamak with alternating current operation is described in the Murakami-Hugill diagram. At the current reversal, the density remains finite. Gas puffing before current reversal allows alternating current operation with larger currents, and improves its reproducibility. A qualitative explanation for the finite plasma density at the current reversal is presented, based on a short-circuit effect by the limiter.

  13. Formation of diamond-like carbon thin films using barrier-type surface discharge plasma under atmospheric pressure

    Science.gov (United States)

    Yasui, Shinji; Tada, Kazuya; Takuwa, Tetsuya

    2016-01-01

    We studied the deposition of diamond-like carbon (DLC) thin films using barrier-type surface discharge plasma under atmospheric pressure. The main radicals generated by the barrier-type surface discharge using H2, CH4, and He as the plasma gases were Hα, Hβ, and CH. The emission intensities increased as the ratio of CH4 in the mixed gas decreased, and the mixed gas ratios of 2% CH4, 18% H2, 80% He were appropriate for the generation of the barrier-type surface discharge. The gas flow rate and applied voltage required to achieve a suitable plasma state for deposition of the DLC films varied depending on the polarity of the applied pulse. When a negative pulse is used, homogenous films can be obtained on the silicon wafer under the entire hole of the electrode; however, the deposition rate becomes very low in the range of 1.8-5.8 nm/min because the surface streamer plasma is very weak. On the other hand, using a bipolar and a positive pulse, a relatively high deposition rate in the range of 10-30 nm/min can be achieved on the silicon wafer under the central part of the electrode, although the thickness of the DLC films becomes nonuniform at the edge part of the electrode. The appropriate conditions of the DLC film deposition in this study were the pulse voltages of 6-8 kV and a gas flow rate of 1500 mL/min when using bipolar- and positive-pulse voltages. The relatively hard DLC films (6-8 GPa) were obtained under these conditions.

  14. The use of segmented cathodes to determine the spoke current density distribution in high power impulse magnetron sputtering plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Poolcharuansin, Phitsanu [Department of Electrical Engineering and Electronics, University of Liverpool, Brownlow Hill, Liverpool L69 3GJ (United Kingdom); The Technological Plasma Research Unit, Department of Physics, Mahasarakham University, Maha Sarakham 44150 (Thailand); Estrin, Francis Lockwood; Bradley, James W., E-mail: j.w.bradley@liverpool.ac.uk [Department of Electrical Engineering and Electronics, University of Liverpool, Brownlow Hill, Liverpool L69 3GJ (United Kingdom)

    2015-04-28

    The localized target current density associated with quasi-periodic ionization zones (spokes) has been measured in a high power impulse magnetron sputtering (HiPIMS) discharge using an array of azimuthally separated and electrical isolated probes incorporated into a circular aluminum target. For a particular range of operating conditions (pulse energies up to 2.2 J and argon pressures from 0.2 to 1.9 Pa), strong oscillations in the probe current density are seen with amplitudes up to 52% above a base value. These perturbations, identified as spokes, travel around the discharge above the target in the E×B direction. Using phase information from the angularly separated probes, the spoke drift speeds, angular frequencies, and mode number have been determined. Generally, at low HiPIMS pulse energies E{sub p} < 0.8 J, spokes appear to be chaotic in nature (with random arrival times), however as E{sub p} increases, coherent spokes are observed with velocities between 6.5 and 10 km s{sup −1} and mode numbers m = 3 or above. At E{sub p} > 1.8 J, the plasma becomes spoke-free. The boundaries between chaotic, coherent, and no-spoke regions are weakly dependent on pressure. During each HiPIMS pulse, the spoke velocities increase by about 50%. Such an observation is explained by considering spoke velocities to be determined by the critical ionization velocity, which changes as the plasma composition changes during the pulse. From the shape of individual current density oscillations, it appears that the leading edge of the spoke is associated with a slow increase in local current density to the target and the rear with a more rapid decrease. The measurements show that the discharge current density associated with individual spokes is broadly spread over a wide region of the target.

  15. Synthesis of Carbon nano structures by plasma discharge; Sintesis de nanoestructuras de carbono por descarga de plasmaa

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez L, M.L

    2007-07-01

    Due to the great quantity of applications of the carbon nano structures (NEC) in diverse areas like: synthesis of super-resistant materials, hydrogen storage, nano sensors generation and nano catalysts, it has seen the necessity to generate new processes of synthesis of this materials as well as to already improve those existent. The present work has as objective to optimize the NEC synthesis process by means of the electric arc method which uses alternating current to high frequencies (HF), obtaining relatively clean products; that is to say, it hardly presents amorphous material neither sludges. They stand out the obtaining of carbon nano fibers (NFC) by means of a luminescent-arch discharge, in a gas mixture of He-CH{sub 4} with 34% at. Ni/10.32% at.Y like catalyst; at a frequency of 42 kHz and low power (300 W). This method benefits the amass of the particles in both electrodes due to the high frequencies. The time of duration of the process oscillates between 5 and 20 minutes. The obtained product was characterized by scanning electron microscopy (MEB), transmission electron microscopy (MET) to determine the NEC type obtained and by X-ray diffraction analysis and Raman spectroscopy for determining the purity of the samples. The NFC is relatively free of amorphous coal. The surface and structural analysis indicates that the fibers have a half diameter of 80 nm. It is also made, a study by optical emission spectroscopy of plasma using the Swan band for determining the temperature. (Author)

  16. Influence of surface-active bonds of carbon structures on discharge-charging processes of a current source

    Science.gov (United States)

    Kuz'menko, A. P.; Grechushnikov, E. A.; Kharseev, V. A.

    2017-09-01

    A study has been carried out of the effect on the discharge-charging processes of a current source of surface-active bonds of carbon structures used as additives in the composition of a negative electrode material. A mechanism has been proposed based on the conclusions derived from the Kossel-Stranski molecularkinetic theory, which explains the growth of 3PbOPbSO4H2O crystals upon the introduction of carbon materials. It has been established that the presence of carbon additives in the composition of the negative electrode material of starter lead-acid batteries increases the capacitance of 20-h discharge mode by up to 5% and the discharge duration by cold scrolling current to a final voltage of 6 V at negative temperatures of-18°C and-30°C by 3-4.5% and 9-13%, respectively.

  17. Absolute number densities of helium metastable atoms determined by atomic absorption spectroscopy in helium plasma-based discharges used as ambient desorption/ionization sources for mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Reininger, Charlotte; Woodfield, Kellie [Brigham Young University, Department of Chemistry and Biochemistry, Provo, UT 84602 (United States); Keelor, Joel D.; Kaylor, Adam; Fernández, Facundo M. [Georgia Institute of Technology, School of Chemistry and Biochemistry, Atlanta, GA 30332 (United States); Farnsworth, Paul B., E-mail: paul_farnsworth@byu.edu [Brigham Young University, Department of Chemistry and Biochemistry, Provo, UT 84602 (United States)

    2014-10-01

    The absolute number densities of helium atoms in the 2s {sup 3}S{sub 1} metastable state were determined in four plasma-based ambient desorption/ionization sources by atomic absorption spectroscopy. The plasmas included a high-frequency dielectric barrier discharge (HF-DBD), a low temperature plasma (LTP), and two atmospheric-pressure glow discharges, one with AC excitation and the other with DC excitation. Peak densities in the luminous plumes downstream from the discharge capillaries of the HF-DBD and the LTP were 1.39 × 10{sup 12} cm{sup −3} and 0.011 × 10{sup 12} cm{sup −3}, respectively. Neither glow discharge produced a visible afterglow, and no metastable atoms were detected downstream from the capillary exits. However, densities of 0.58 × 10{sup 12} cm{sup −3} and 0.97 × 10{sup 12} cm{sup −3} were measured in the interelectrode regions of the AC and DC glow discharges, respectively. Time-resolved measurements of metastable atom densities revealed significant random variations in the timing of pulsed absorption signals with respect to the voltage waveforms applied to the discharges. - Highlights: • We determine He metastable number densities for four plasma types • The highest number densities were observed in a dielectric barrier discharge • No helium metastable atoms were observed downstream from the exits of glow discharges.

  18. One-step preparation of nanostructured martite catalyst and graphite electrode by glow discharge plasma for heterogeneous electro-Fenton like process.

    Science.gov (United States)

    Khataee, Alireza; Sajjadi, Saeed; Hasanzadeh, Aliyeh; Vahid, Behrouz; Joo, Sang Woo

    2017-09-01

    Natural Martite ore particles and graphite were modified by alternating current (AC) glow discharge plasma to form nanostructured catalyst and cathode electrode for using in the heterogeneous-electro Fenton-like (Het-EF-like) process. The performance of the plasma-treated martite (PTM) and graphite electrode (PTGE) was studied for the treatment of paraquat herbicide in a batch system. 85.78% degradation efficiency for 20 mg L -1 paraquat was achieved in the modified process under desired operational conditions (i.e. current intensity of 300 mA, catalyst amount of 1 g L -1 , pH = 6, and background electrolyte (Na 2 SO 4 ) concentration of 0.05 mol L -1 ) which was higher than the 41.03% for the unmodified one after 150 min of treatment. The ecofriendly modification of the martite particles and the graphite electrode, no chemical needed, low leached iron and milder operational pH were the main privileges of plasma utilization. Moreover, the degradation efficiency through the process was not declined after five repeated cycles at the optimized conditions, which proved the stability of the nanostructured PTM and PTGE in the long-term usage. The archived results exhibit this method is the first example of high efficient, cost-effective, and environment-friendly method for generation of nanostructured samples. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Self-enhanced plasma discharge effect in the deposition of diamond-like carbon films on the inner surface of slender tube

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yi [Department of 702, Beihang University, Beijing (China); Li, Liuhe, E-mail: liliuhe@buaa.edu.cn [Department of 702, Beihang University, Beijing (China); Luo, Sida [Department of 702, Beihang University, Beijing (China); International Research Institute for Multidisciplinary Science, Beihang University, Beijing (China); Lu, Qiuyuan [Dong Feng Commercial Vehicle Technical Center, Dong Feng Commercial Vehicle Co., LTD, Wuhan (China); Gu, Jiabin; Lei, Ning [Department of 702, Beihang University, Beijing (China); Huo, Chunqin [Key Laboratory of Optoelectronic Devices and Systems of Ministry of Education, Shenzhen University, Guangdong (China)

    2017-01-30

    Highlights: • Effect of inner surface materials of tubes on plasma discharge is examined. • Electron mean free path is used to analyze the films deposition. • Secondary electrons emitted from inner surface of tube enhance plasma discharge. - Abstract: Enhanced glow discharge plasma immersion ion implantation and deposition (EGD-PIII&D) have been proved to be highly effective for depositing diamond-like carbon (DLC) films on the inner surface of the slender quartz tube with a deposition rate of 1.3 μm/min. Such a high-efficiency DLC films deposition was explained previously as the short electrons mean free path to cause large collision frequency between electrons and neutral particles. However, in this paper, we found that the inner surface material of the tube itself play a vital role on the films deposition. To disclose the mechanism of this phenomenon, the effect of different inner surface materials on plasma discharge was experimentally and theoretically investigated. Then a self-enhancing plasma discharge is discovered. It is found that secondary electrons emitted from the inner surface material, whatever it is the tube inner surface or deposited DLC films, can dramatically enhance the plasma discharge to improve the DLC films deposition rate.

  20. Simulation of impurity transport in the peripheral plasma due to the emission of dust in long pulse discharges on the Large Helical Device

    Directory of Open Access Journals (Sweden)

    M. Shoji

    2017-08-01

    Full Text Available Two different plasma termination processes by dust emission were observed in long pulse discharges in the Large Helical Device. One is a plasma termination caused by large amounts of carbon dust released from a lower divertor region. The other is termination caused by stainless steel (iron dust emission from the surface of a helical coil can. The effect of the dust emission on the sustainment of the long pulse discharges are investigated using a three-dimensional edge plasma transport code (EMC3-EIRENE coupled with a dust transport code (DUSTT. The simulation shows that the plasma is more influenced by the iron dust emission from the helical coil can than by the carbon dust emission from the divertor region. The simulation revealed that the plasma flow in divertor legs is quite effective for preventing dust from terminating the long pulse discharges.

  1. Current Magnitude and Mechanisms of Groundwater Discharge in the Arctic: Case Study from Alaska.

    Science.gov (United States)

    Dimova, Natasha T; Paytan, Adina; Kessler, John D; Sparrow, Katy J; Garcia-Tigreros Kodovska, Fenix; Lecher, Alanna L; Murray, Joseph; Tulaczyk, Slawomir M

    2015-10-20

    To better understand groundwater-surface water dynamics in high latitude areas, we conducted a field study at three sites in Alaska with varying permafrost coverage. The natural groundwater tracer ((222)Rn, radon) was used to evaluate groundwater discharge, and electrical resistivity tomography (ERT) was used to examine subsurface mixing dynamics. Different controls govern groundwater discharge at these sites. In areas with sporadic permafrost (Kasitsna Bay), the major driver of submarine groundwater discharge is tidal pumping, due to the large tidal oscillations, whereas at Point Barrow, a site with continuous permafrost and small tidal amplitudes, fluxes are mostly affected by seasonal permafrost thawing. Extended areas of low resistivity in the subsurface alongshore combined with high radon in surface water suggests that groundwater-surface water interactions might enhance heat transport into deeper permafrost layers promoting permafrost thawing, thereby enhancing groundwater discharge.

  2. Gas flow rate dependence of the discharge characteristics of a helium atmospheric pressure plasma jet interacting with a substrate

    Science.gov (United States)

    Yan, Wen; Economou, Demetre J.

    2017-10-01

    A 2D (axisymmetric) computational study of the discharge characteristics of an atmospheric pressure plasma jet as a function of gas flow rate was performed. The helium jet emerged from a dielectric tube, with an average gas flow velocity in the range 2.5-20 m s-1 (1 atm, 300 K) in a nitrogen ambient, and impinged on a substrate a short distance dowstream. The effect of the substrate conductivity (conductror versus insulator) was also studied. Whenever possible, simulation predictions were compared with published experimental observations. Discharge ignition and propagation in the dielectric tube were hardly affected by the He gas flow velocity. Most properties of the plasma jet, however, depended sensitively on the He gas flow velocity, which determined the concentration distributions of helium and nitrogen in the mixing layer forming in the gap between the tube exit and the substrate. At low gas flow velocity, the plasma jet evolved from a hollow (donut-shaped) feature to one where the maximum of electron density was on axis. When the gas flow velocity was high, the plasma jet maintained its hollow structure until it struck the substrate. For a conductive substrate, the radial ion fluxes to the surface were relatively uniform over a radius of ~0.4-0.8 mm, and the dominant ion flux was that of He+. For a dielectric substrate, the radial ion fluxes to the surface peaked on the symmetry axis at low He gas flow velocity, but a hollow ion flux distribution was observed at high gas flow velocity. At the same time, the main ion flux switched from N2+ to He2+ as the He gas flow velocity increased from a low to a high value. The diameter of the plasma ‘footprint’ on the substrate first increased with increasing He gas flow velocity, and eventually saturated with further increases in velocity.

  3. Atmospheric Pressure Non-Thermal Plasma Activation of CO2in a Packed-Bed Dielectric Barrier Discharge Reactor.

    Science.gov (United States)

    Mei, Danhua; Tu, Xin

    2017-11-17

    Direct conversion of CO 2 into CO and O 2 is performed in a packed-bed dielectric barrier discharge (DBD) non-thermal plasma reactor at low temperatures and atmospheric pressure. The maximum CO 2 conversion of 22.6 % is achieved when BaTiO 3 pellets are fully packed into the discharge gap. The introduction of γ-Al 2 O 3 or 10 wt % Ni/γ-Al 2 O 3 catalyst into the BaTiO 3 packed DBD reactor increases both CO 2 conversion and energy efficiency of the plasma process. Packing γ-Al 2 O 3 or 10 wt % Ni/γ-Al 2 O 3 upstream of the BaTiO 3 bed shows higher CO 2 conversion and energy efficiency compared with that of mid- or downstream packing modes because the reverse reaction of CO 2 conversion-the recombination of CO and O to form CO 2 -is more likely to occur in mid- and downstream modes. Compared with the γ-Al 2 O 3 support, the coupling of the DBD with the Ni catalyst shows a higher CO 2 conversion, which can be attributed to the presence of Ni active species on the catalyst surface. The argon plasma treatment of the reacted Ni catalyst provides extra evidence to confirm the role of Ni active species in the conversion of CO 2 . © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. A Microwave Plasma Discharge in Rare Gases as a VUV Source for Planetary Atmospheric Photochemistry

    OpenAIRE

    Tigrine, Sarah; Carrasco, Nathalie; Vettier, Ludovic; Cernogora, Guy

    2016-01-01

    International audience; The aim of this work is to show that micro-wave discharges in rare gases, can be an efficient windowless VUV photon source for planetaryatmospheric photochemistry experiments. In this context, we perform a microwave discharge (surfatron) in a neon gas flow. We characterizethe VUV photon flux emitted in different conditions, when working in the mbar pressure range, and compare it to synchrotron VUV fluxes alsoused for similar applications.

  5. Feedback model of secondary electron emission in DC gas discharge plasmas

    Science.gov (United States)

    Saravanan, ARUMUGAM; Prince, ALEX; Suraj, Kumar SINHA

    2018-01-01

    Feedback is said to exist in any amplifier when the fraction of output power in fed back as an input. Similarly, in gaseous discharge ions that incident on the cathode act as a natural feedback element to stabilize and self sustain the discharge. The present investigation is intended to emphasize the feedback nature of ions that emits secondary electrons (SEs) from the cathode surface in DC gas discharges. The average number of SEs emitted per incident ion and non ionic species (energetic neutrals, metastables and photons) which results from ion is defined as effective secondary electron emission coefficient (ESEEC,{γ }{{E}}). In this study, we derive an analytic expression that corroborates the relation between {γ }{{E}} and power influx by ion to the cathode based on the feedback theory of an amplifier. In addition, experimentally, we confirmed the typical positive feedback nature of SEE from the cathode in argon DC glow discharges. The experiment is done for three different cathode material of same dimension (tungsten (W), copper (Cu) and brass) under identical discharge conditions (pressure: 0.45 mbar, cathode bias: ‑600 V, discharge gab: 15 cm and operating gas: argon). Further, we found that the {γ }{{E}} value of these cathode material controls the amount of feedback power given by ions. The difference in feedback leads different final output i.e the power carried by ion at cathode ({P}{{i}}{\\prime }{| }{{C}}). The experimentally obtained value of {P}{{i}}{\\prime }{| }{{C}} is 4.28 W, 6.87 W and 9.26 W respectively for W, Cu and brass. In addition, the present investigation reveals that the amount of feedback power in a DC gas discharges not only affect the fraction of power fed back to the cathode but also the entire characteristics of the discharge.

  6. The application of a non-thermal plasma generated by gas-liquid gliding arc discharge in sterilization

    Science.gov (United States)

    Du, Chang Ming; Wang, Jing; Zhang, Lu; Xia Li, Hong; Liu, Hui; Xiong, Ya

    2012-01-01

    Gliding arc discharge has been investigated in recent years as an innovative physicochemical technique for contaminated water treatment at atmospheric pressure and ambient temperature. In this study we tested a gas-liquid gliding arc discharge reactor, the bacterial suspension of which was treated circularly. When the bacterial suspension was passed through the electrodes and circulated at defined flow rates, almost 100% of the bacteria were killed in less than 3.0 min. Experimental results showed that it is possible to achieve an abatement of 7.0 decimal logarithm units within only 30 s. Circulation flow rates and types of feeding gas caused a certain impact on bacteria inactivation, but the influences are not obvious. So, under the promise of sterilization effect, industrial applications can select their appropriate operating conditions. All inactivation curves presented the same three-phase profile showing an apparent sterilization effect. Analysis of the scanning electron microscope images of bacterial cells supports the speculation that the gas-liquid gliding arc discharge plasma is acting under various mechanisms driven essentially by oxidation and the effect of electric field. These results enhance the possibility of applying gas-liquid gliding arc discharge decontamination systems to disinfect bacterial-contaminated water. Furthermore, correlational research indicates the potential applica