Experimental study on a wide range of wave and current conditions of the WEPTOS Wave Energy Converter

DEFF Research Database (Denmark)

Pecher, Arthur; Kofoed, Jens Peter

This report presents the results of an experimental study that was performed on small scale model that was a replication of the full-scale Weptos WEC intended for DanWEC. The tests were performed in the circular basin at FloWave at Edinburgh University in October 2014. The laboratory facilities h...... the capabilities to have simultaneously currents and waves from any possible direction and also to produce advanced wave specifications....

Coordination between Fault-Ride-Through Capability and Over-current Protection of DFIG Generators for Wind Farms

DEFF Research Database (Denmark)

Bak-Jensen, Birgitte; Kawady, T.A.; Abdel-Rahman, Mansour Hassan

2010-01-01

is investigated. Simulation test cases using MATLAB-Simulink are implemented on a 365-MW wind farm in AL-Zaafarana, Egypt. The simulation results show the influence of the FRT capability on the protective relaying coordination in wind farms, showing that the FRT may work in situations where is were expected......Fault Ride-Through (FRT) capabilities set up according to the grid codes may affect the performance of related protective elements during fault periods. Therefore, in this paper the coordination between the FRT capability and over-current protection of DFIG Wind Generators in MV networks...... not to work, and then disabling the over-current protection, which should have worked in this situation....

Current Capabilities and Capacity of Ebola Treatment Centers in the United States.

Science.gov (United States)

Herstein, Jocelyn J; Biddinger, Paul D; Kraft, Colleen S; Saiman, Lisa; Gibbs, Shawn G; Le, Aurora B; Smith, Philip W; Hewlett, Angela L; Lowe, John J

2016-03-01

To describe current Ebola treatment center (ETC) locations, their capacity to care for Ebola virus disease patients, and infection control infrastructure features. A 19-question survey was distributed electronically in April 2015. Responses were collected via email by June 2015 and analyzed in an electronic spreadsheet. The survey was sent to and completed by site representatives of each ETC. The survey was sent to all 55 ETCs; 47 (85%) responded. Of the 47 responding ETCs, there are 84 isolation beds available for adults and 91 for children; of these pediatric beds, 35 (38%) are in children's hospitals. In total, the simultaneous capacity of the 47 reporting ETCs is 121 beds. On the basis of the current US census, there are 0.38 beds per million population. Most ETCs have negative pressure isolation rooms, anterooms, and a process for category A waste sterilization, although only 11 facilities (23%) have the capability to sterilize infectious waste on site. Facilities developed ETCs on the basis of Centers for Disease Control and Prevention guidance, but specific capabilities are not mandated at this present time. Owing to the complex and costly nature of Ebola virus disease treatment and variability in capabilities from facility to facility, in conjunction with the lack of regulations, nationwide capacity in specialized facilities is limited. Further assessments should determine whether ETCs can adapt to safely manage other highly infectious disease threats.

Some current experimental challenges in elementary particle physics

Energy Technology Data Exchange (ETDEWEB)

Cline, D.B. (California Univ., Los Angeles (USA). Dept. of Physics)

1990-06-01

We describe three experimental challenges for experimental elementary particle physics: (1) the ongoing search for flavor changing weak neutral currents, including future prospect for a anti BB factory, (2) the status of the tests of the standard model in the W, Z and t quark sectors and (3) some current search for physics beyond the standard model, to include the possibility of searching for CPT violation using a {Phi} factory. (orig.).

Sensing capabilities of graphite based MR elastomers

International Nuclear Information System (INIS)

Tian, T F; Li, W H; Deng, Y M

2011-01-01

This paper presents both experimental and theoretical investigations of the sensing capabilities of graphite based magnetorheological elastomers (MREs). In this study, eight MRE samples with varying graphite weight fractions were fabricated and their resistance under different magnetic fields and external loadings were measured with a multi-meter. With an increment of graphite weight fraction, the resistance of MRE sample decreases steadily. Higher magnetic fields result in a resistance increase. Based on an ideal assumption of a perfect chain structure, a mathematical model was developed to investigate the relationship between the MRE resistance with external loading. In this model, the current flowing through the chain structure consists of both a tunnel current and a conductivity current, both of which depend on external loadings. The modelling parameters have been identified and reconstructed from comparison with experimental results. The comparison indicates that both experimental results and modelling predictions agree favourably well

Recent Investments by NASA's National Force Measurement Technology Capability

Science.gov (United States)

Commo, Sean A.; Ponder, Jonathan D.

2016-01-01

The National Force Measurement Technology Capability (NFMTC) is a nationwide partnership established in 2008 and sponsored by NASA's Aeronautics Evaluation and Test Capabilities (AETC) project to maintain and further develop force measurement capabilities. The NFMTC focuses on force measurement in wind tunnels and provides operational support in addition to conducting balance research. Based on force measurement capability challenges, strategic investments into research tasks are designed to meet the experimental requirements of current and future aerospace research programs and projects. This paper highlights recent and force measurement investments into several areas including recapitalizing the strain-gage balance inventory, developing balance best practices, improving calibration and facility capabilities, and researching potential technologies to advance balance capabilities.

High-voltage integrated linear regulator with current sinking capabilities for portable ultrasound scanners

DEFF Research Database (Denmark)

Pausas, Guifre Vendrell; Llimos Muntal, Pere; Jørgensen, Ivan Harald Holger

2017-01-01

This paper presents a high-voltage integrated regulator capable of sinking current for driving pulse-triggered level shifters in drivers for ultrasound applications. The regulator utilizes a new topology with a feedback loop and a current sinking circuit to satisfy the requirements of the portable....... The proposed design has been implemented in high-voltage 0.18 μm process whithin an area of 0.11 mm2 and it is suitable for system-on-chip integration due to its low component count and the fully integrated design....

Experimental studies of coaxial plasma gun current

International Nuclear Information System (INIS)

Price, D.W.

1988-01-01

In this investigation of a coaxial plasma gun, plasma sheath currents and related behavior are examined. Plasma behavior in the gun affects gun characteristics. Plasma gun applications are determined by the plasma behavior. The AFWL PUFF capacitor bank (72 μF, 29 nH, 120 kV) drives the plasma gun using a deuterium fill gas. The gas breakdown site is isolated from the dielectric/vacuum interface in the AFWL system. Two gas values deliver gas in the system. The first delivers gas from the gun breech and the second optional valve delivers gas to the gun muzzle. Currents and voltages are measured by Rogowski coils, B probes and capacitive voltage probes. A O-D slug model is used to predict the current, inductance, gun voltage and plasma sheath velocity. The slug model assumes the sheath transits the gun with all mass in the sheath. In the snowplow mode, the plasma sheath is thin with a sharp current rise and drop. Our system operated in a transition mode between the snowplow and deflagration modes with early snowplow behavior and late deflagration behavior. Neutrons are produced in a plasma pinch at the gun muzzle, indicating snowplow behavior. The slug theory models overall gun behavior to experimental accuracy. Experimental results are compared to four theories for plasma sheath velocities: the Alfven collisionally limited model, the Rosenbluth model, the Fishbine saturated model and a single particle drift model. Experimental velocities vary from 10 5 to 10 6 m/s. Only the single particle drift and the slug model calculations are of the right magnitude (8 x 10 5 m/s). The Fishbine and the Rosenbluth models predict slower velocities (2 x 10 5 m/s). The Alfven model is not applicable to this system

Experimental investigation on the relationship between sluice caisson shape of tidal power plant and the water discharge capability

Energy Technology Data Exchange (ETDEWEB)

Lee, Dal Soo; Oh, Sang-Ho; Yi, Jin-Hak; Park, Woo-Sun [Coastal Engineering and Ocean Energy Research Department, Korea Ocean Research and Development Institute, Ansan 426-744 (Korea); Cho, Hyu-Sang; Kim, Duk-Gu; Ahn, Suk-Jin [Technology Research and Development Institute, Hyein E and C Co. Ltd., Seoul 157-861 (Korea); Eom, Hyun-Min [Global Environment System Research Laboratory, National Institute of Meteorological Research/KMA, Seoul 156-720 (Korea)

2010-10-15

The change of water discharge capability of the sluice caisson of tidal power plant according to the change of geometrical shape of the sluice caisson was investigated by performing laboratory experiments. The major design parameters that constitute general shape of the sluice caisson were deduced and a total of 32 different shapes of sluice caisson models were subjected to the hydraulic experiments. For every sluice caisson model, the water discharge capability was estimated with five different flow rates and three different water level conditions. The experiments were carried out in an open channel flume with a great care to measure flow rate and water level accurately, which are key physical quantities in estimating the water discharge capability of the sluice caisson models. By analyzing the experimental results, influence of the respective design parameters on the performance of the sluice caisson was examined and the general guidelines to enhance the water discharge capability were suggested. The discharge coefficient of the best sluice caisson model ranged from 2.3 to 3.1 depending on the experimental conditions, which is far higher than the values that were adopted in the past feasibility studies in Korea. (author)

Thermoelectric Generation Of Current - Theoretical And Experimental Analysis

Science.gov (United States)

Ruciński, Adam; Rusowicz, Artur

2017-12-01

This paper provides some information about thermoelectric technology. Some new materials with improved figures of merit are presented. These materials in Peltier modules make it possible to generate electric current thanks to a temperature difference. The paper indicates possible applications of thermoelectric modules as interesting tools for using various waste heat sources. Some zero-dimensional equations describing the conditions of electric power generation are given. Also, operating parameters of Peltier modules, such as voltage and electric current, are analyzed. The paper shows chosen characteristics of power generation parameters. Then, an experimental stand for ongoing research and experimental measurements are described. The authors consider the resistance of a receiver placed in the electric circuit with thermoelectric elements. Finally, both the analysis of experimental results and conclusions drawn from theoretical findings are presented. Voltage generation of about 1.5 to 2.5 V for the temperature difference from 65 to 85 K was observed when a bismuth telluride thermoelectric couple (traditionally used in cooling technology) was used.

Diode-Assisted Buck-Boost Current Source Inverters

DEFF Research Database (Denmark)

Gao, F.; Cai, Liang; Loh, P.C.

2007-01-01

This paper presents a couple of novel current source inverters (CSIs) with the enhanced current buckboost capability. With the unique diode-inductor network added between current source inverter circuitry and current boost elements, the proposed buck-boost current source inverters demonstrate...... uninfluenced. Lastly, all theoretical findings were verified experimentally using constructed laboratory prototypes....

Fault Ride-through Capability Enhancement of Voltage Source Converter-High Voltage Direct Current Systems with Bridge Type Fault Current Limiters

Directory of Open Access Journals (Sweden)

Md Shafiul Alam

2017-11-01

Full Text Available This paper proposes the use of bridge type fault current limiters (BFCLs as a potential solution to reduce the impact of fault disturbance on voltage source converter-based high voltage DC (VSC-HVDC systems. Since VSC-HVDC systems are vulnerable to faults, it is essential to enhance the fault ride-through (FRT capability with auxiliary control devices like BFCLs. BFCL controllers have been developed to limit the fault current during the inception of system disturbances. Real and reactive power controllers for the VSC-HVDC have been developed based on current control mode. DC link voltage control has been achieved by a feedback mechanism such that net power exchange with DC link capacitor is zero. A grid-connected VSC-HVDC system and a wind farm integrated VSC-HVDC system along with the proposed BFCL and associated controllers have been implemented in a real time digital simulator (RTDS. Symmetrical three phase as well as different types of unsymmetrical faults have been applied in the systems in order to show the effectiveness of the proposed BFCL solution. DC link voltage fluctuation, machine speed and active power oscillation have been greatly suppressed with the proposed BFCL. Another significant feature of this work is that the performance of the proposed BFCL in VSC-HVDC systems is compared to that of series dynamic braking resistor (SDBR. Comparative results show that the proposed BFCL is superior over SDBR in limiting fault current as well as improving system fault ride through (FRT capability.

Assessment of CFD capability for prediction of hypersonic shock interactions

Science.gov (United States)

Knight, Doyle; Longo, José; Drikakis, Dimitris; Gaitonde, Datta; Lani, Andrea; Nompelis, Ioannis; Reimann, Bodo; Walpot, Louis

2012-01-01

The aerothermodynamic loadings associated with shock wave boundary layer interactions (shock interactions) must be carefully considered in the design of hypersonic air vehicles. The capability of Computational Fluid Dynamics (CFD) software to accurately predict hypersonic shock wave laminar boundary layer interactions is examined. A series of independent computations performed by researchers in the US and Europe are presented for two generic configurations (double cone and cylinder) and compared with experimental data. The results illustrate the current capabilities and limitations of modern CFD methods for these flows.

Study of magnetorheology and sensing capabilities of MR elastomers

International Nuclear Information System (INIS)

Tian, T F; Li, W H; Alici, G

2013-01-01

This study focuses on the magnetorheology and sensing capability of graphite based Magnetorheological Elastomers (Gr MREs). By introducing graphite (Gr) to conventional MREs, the Gr MREs are derived. The anisotropic sample with 20% graphite weight fraction was selected to be compared with anisotropic conventional MREs. The microstructures of anisotropic Gr MREs and conventional MREs were observed. Both steady state tests and dynamic tests were conducted to study rheological properties of the samples. For dynamic tests, the effects of strain amplitude, and frequency on both storage modulus and loss modulus were measured. For sensing capability, the resistance of selected Gr MREs under different magnetic fields and external loadings is measured with a multi-meter. Either higher magnetic field or more external loading results in the resistance increment. Based on an ideal assumption of perfect chain structure, a mathematical model was proposed to investigate the relationship between the MRE resistance with the external loadings. In this model, the current flowing through the chain structure consists of both tunnel current and conductivity current, both of which depends on external loadings. The modelling parameters were identified and reconstructed from comparison with experimental results. The comparison indicates that both experimental results and modelling prediction agree favourably well.

An Overview of Current and Future Stratospheric Balloon Mission Capabilities

Science.gov (United States)

Smith, Michael

The modern stratospheric balloon has been used for a variety of missions since the late 1940's. Capabilities of these vehicles to carry larger payloads, fly to higher altitudes, and fly for longer periods of time have increased dramatically over this time. In addition to these basic performance metrics, reliability statistics for balloons have reached unprecedented levels in recent years. Balloon technology developed in the United States in the last decade has the potential to open a new era in economical space science using balloons. As always, the advantage of the balloon platform is the fact that missions can be carried out at a fraction of the cost and schedule of orbital missions. A secondary advantage is the fact that instruments can be re-flown numerous times while upgrading sensor and data processing technologies from year to year. New mission capabilities now have the potential for enabling ground breaking observations using balloons as the primary platform as opposed to a stepping stone to eventual orbital observatories. The limit of very high altitude balloon missions will be explored with respect to the current state of the art of balloon materials and fabrication. The same technological enablers will also be applied to possibilities for long duration missions at mid latitudes with payloads of several tons. The balloon types and their corresponding mission profiles will be presented in a performance matrix that will be useful for potential scientific users in planning future research programs.

Experimental testing and modelling of a resistive type superconducting fault current limiter using MgB2 wire

International Nuclear Information System (INIS)

Smith, A C; Pei, X; Oliver, A; Husband, M; Rindfleisch, M

2012-01-01

A prototype resistive superconducting fault current limiter (SFCL) was developed using single-strand round magnesium diboride (MgB 2 ) wire. The MgB 2 wire was wound with an interleaved arrangement to minimize coil inductance and provide adequate inter-turn voltage withstand capability. The temperature profile from 30 to 40 K and frequency profile from 10 to 100 Hz at 25 K were tested and reported. The quench properties of the prototype coil were tested using a high current test circuit. The fault current was limited by the prototype coil within the first quarter-cycle. The prototype coil demonstrated reliable and repeatable current limiting properties and was able to withstand a potential peak current of 372 A for one second without any degradation of performance. A three-strand SFCL coil was investigated and demonstrated scaled-up current capacity. An analytical model to predict the behaviour of the prototype single-strand SFCL coil was developed using an adiabatic boundary condition on the outer surface of the wire. The predicted fault current using the analytical model showed very good correlation with the experimental test results. The analytical model and a finite element thermal model were used to predict the temperature rise of the wire during a fault. (paper)

Correlates of experimentation with smoking and current cigarette consumption among adolescents* **

Science.gov (United States)

Bonilha, Amanda Gimenes; Ruffino-Netto, Antonio; Sicchieri, Mayara Piani; Achcar, Jorge Alberto; Rodrigues-Júnior, Antonio Luiz; Baddini-Martinez, José

2014-01-01

OBJECTIVE: The aim of this study was to analyze social characteristics and stress as correlates of cigarette smoking in adolescence. The main intent was to identify elements that distinguish adolescents who had experimented with smoking and did not progress to regular smoking from those who became current smokers. METHODS: Students at 10 high schools in the city of Ribeirão Preto, Brazil, completed a questionnaire based on an instrument employed in a similar large-scale study. The students were classified as never-smokers or experimenters. The experimenters were subcategorized as having become current smokers or nonprogressors. Analyses were performed using adjusted logistic models. RESULTS: A total of 2,014 students (mean age, 16.2 ± 1.1 years; females, 53%) completed the questionnaire. We categorized 1,283 students (63.7%) as never-smokers, 244 (12.1%) as current smokers, and 487 (24.2%) as nonprogressors. We found that experimentation with smoking was associated with being held back a grade in school (OR = 1.80), alcohol intake (low/occasional, OR = 8.92; high/regular, OR = 2.64), illicit drug use (OR = 9.32), having a sibling or cousin who smokes (OR = 1.39), having a friend who smokes (OR = 2.08), and high levels of stress (in females only, OR = 1.32). Factors associated with an increased risk of transitioning from experimenter to current smoker were alcohol intake (low/occasional, OR = 3.28; high/regular, OR = 2.16), illicit drug use (OR = 3.61), and having a friend who smokes (OR = 7.20). CONCLUSIONS: Current smoking was associated with a profile of socioeconomic correlates different from that associated with experimentation only. Our data (showing that current smoking was associated with having a friend who smokes, alcohol intake, and illicit drug use) suggest the need for comprehensive approaches to discourage substance use during adolescence. PMID:25610504

Correlates of experimentation with smoking and current cigarette consumption among adolescents

Directory of Open Access Journals (Sweden)

Amanda Gimenes Bonilha

2014-12-01

Full Text Available OBJECTIVE: The aim of this study was to analyze social characteristics and stress as correlates of cigarette smoking in adolescence. The main intent was to identify elements that distinguish adolescents who had experimented with smoking and did not progress to regular smoking from those who became current smokers. METHODS: Students at 10 high schools in the city of Ribeirão Preto, Brazil, completed a questionnaire based on an instrument employed in a similar large-scale study. The students were classified as never-smokers or experimenters. The experimenters were subcategorized as having become current smokers or nonprogressors. Analyses were performed using adjusted logistic models. RESULTS: A total of 2,014 students (mean age, 16.2 ± 1.1 years; females, 53% completed the questionnaire. We categorized 1,283 students (63.7% as never-smokers, 244 (12.1% as current smokers, and 487 (24.2% as nonprogressors. We found that experimentation with smoking was associated with being held back a grade in school (OR = 1.80, alcohol intake (low/occasional, OR = 8.92; high/regular, OR = 2.64, illicit drug use (OR = 9.32, having a sibling or cousin who smokes (OR = 1.39, having a friend who smokes (OR = 2.08, and high levels of stress (in females only, OR = 1.32. Factors associated with an increased risk of transitioning from experimenter to current smoker were alcohol intake (low/occasional, OR = 3.28; high/regular, OR = 2.16, illicit drug use (OR = 3.61, and having a friend who smokes (OR = 7.20. CONCLUSIONS: Current smoking was associated with a profile of socioeconomic correlates different from that associated with experimentation only. Our data (showing that current smoking was associated with having a friend who smokes, alcohol intake, and illicit drug use suggest the need for comprehensive approaches to discourage substance use during adolescence.

Experimental Determination of Bed Conditions in Concentrated Pyroclastic Density Currents

Science.gov (United States)

Winner, A.; Ferrier, K.; Dufek, J.

2016-12-01

Pyroclastic density currents (PDCs) are ground-hugging mixtures of hot gas and rock that can reach temperatures > 800 oC and speeds of 200 m/s. These flows are capable of eroding and entraining the underlying bed material into the flow, which can strongly influence flow momentum, runout distance, and hazards associated with PDCs. However, the mechanism of erosion remains poorly constrained, with proposed mechanisms including under-pressure following the head of the fluidized current, force chain enhanced stresses at the bed, and discrete particle impacts and friction. The interactions between PDCs and the bed have been difficult to observe in the field, as their infrequent occurrence, opacity, and hostile environment make real-time measurement difficult. This study is aimed at obtaining a better understanding of the interactions between PDCs and the bed through a quantitative analysis of bed forces. Our experimental apparatus consists of a rotating cylindrical flume of radius 22 cm, within which gas-rich granular material flows along the interior of the cylinder as it rotates. By using a rotating cylinder, we are able to simulate long-duration flows, allowing us to observe impact forces at the bed over timescales comparable to the flow duration of natural PDCs. To measure the distribution and evolution of forces imparted by the flow on the bed, we constructed a cylindrical insert with a non-erodible bed in which we embedded force sensor arrays parallel and perpendicular to the direction of flow. To measure the forces felt by the particles in the flow, we added "smart particles" 25 to 50 mm in diameter to the flow. Each smart particle contains a three-axis accelerometer and a micro SD card enclosed in a spherical plastic casing, and possesses a density similar to that of the pumice in the experimental flow. Each smart particle also contains a three-axis magnetometer which permits its location to be tracked by means of a unique applied magnetic field. Ultimately

Thermoelectric Generation Of Current – Theoretical And Experimental Analysis

Directory of Open Access Journals (Sweden)

Ruciński Adam

2017-12-01

Full Text Available This paper provides some information about thermoelectric technology. Some new materials with improved figures of merit are presented. These materials in Peltier modules make it possible to generate electric current thanks to a temperature difference. The paper indicates possible applications of thermoelectric modules as interesting tools for using various waste heat sources. Some zero-dimensional equations describing the conditions of electric power generation are given. Also, operating parameters of Peltier modules, such as voltage and electric current, are analyzed. The paper shows chosen characteristics of power generation parameters. Then, an experimental stand for ongoing research and experimental measurements are described. The authors consider the resistance of a receiver placed in the electric circuit with thermoelectric elements. Finally, both the analysis of experimental results and conclusions drawn from theoretical findings are presented. Voltage generation of about 1.5 to 2.5 V for the temperature difference from 65 to 85 K was observed when a bismuth telluride thermoelectric couple (traditionally used in cooling technology was used.

LAMPF experimental-area beam current monitors

International Nuclear Information System (INIS)

Tallerico, P.J.

1975-01-01

This paper summarizes the design and operational performance of a wide- range current monitor system used to measure charged-particle currents in the experimental areas of the Clinton P. Anderson Meson Physics Facility (LAMPF), a proton accelerator. The major features of the system are high sensitivity, wide dynamic range, and the ability to withstand high levels of radiation. The current pulses detected are from 50 μs to 1 ms in duration at repetition rates of from 1 to 120 Hz. The pulse amplitude varies from 1 μA to 17 mA of protons or H - ions. Both real-time and integrated outputs are available, and the minimum detectable currents are 1 μA at the video output and 50 nA at the integrated output. The basic system is comprised of toroids, preamplifiers, signal conditioners, voltage-to-frequency converters, and digital accumulators. The entire system is spread out over 1 km of beam pipe. Provision is made for calibration and for sending the outputs to remote users. The system is normally controlled by a small digital computer, which allows the system to be quite flexible in operation. The design features of the toroids and the associated electronics are discussed in detail, with emphasis on the steps taken to reduce noise and make the toroids temperature and radiation resistant

Materials Capability Review Los Alamos National Laboratory April 29-May 2, 2012

Energy Technology Data Exchange (ETDEWEB)

Taylor, Antoinette J [Los Alamos National Laboratory

2012-04-20

Los Alamos National Laboratory (LANL) uses Capability Reviews to assess the quality and institutional integration of science, technology and engineering (STE) and to advise Laboratory Management on the current and future health of LANL STE. The capabilities are deliberately chosen to be crosscutting over the Laboratory and therefore will include experimental, theoretical and simulation disciplines from multiple line organizations. Capability Reviews are designed to provide a more holistic view of the STE quality, integration to achieve mission requirements, and mission relevance. The scope of these capabilities necessitate that there will be significant overlap in technical areas covered by capability reviews (e.g., materials research and weapons science and engineering). In addition, LANL staff may be reviewed in different capability reviews because of their varied assignments and expertise. The principal product of the Capability Review is the report that includes the review committee's assessments, recommendations, and recommendations for STE.

The ESA River & Lake System: Current Capabilities and Future Potential

DEFF Research Database (Denmark)

Smith, Richard G.; Salloway, Mark; Berry, Philippa A. M.

Measuring the earth's river and lake resources using satellite radar altimetry offers a unique global monitoring capability, which complements the detailed measurements made by the steadily decreasing number of in-situ gauges. To exploit this unique remote monitoring capability, a global pilot...

Synthetic aperture radar capabilities in development

Energy Technology Data Exchange (ETDEWEB)

Miller, M. [Lawrence Livermore National Lab., CA (United States)

1994-11-15

The Imaging and Detection Program (IDP) within the Laser Program is currently developing an X-band Synthetic Aperture Radar (SAR) to support the Joint US/UK Radar Ocean Imaging Program. The radar system will be mounted in the program`s Airborne Experimental Test-Bed (AETB), where the initial mission is to image ocean surfaces and better understand the physics of low grazing angle backscatter. The Synthetic Aperture Radar presentation will discuss its overall functionality and a brief discussion on the AETB`s capabilities. Vital subsystems including radar, computer, navigation, antenna stabilization, and SAR focusing algorithms will be examined in more detail.

Enhancing the capabilities of eddy current techniques for non-destructive evaluation of austenitic stainless steels

International Nuclear Information System (INIS)

Rao, B.P.C.; Thirunavukkarasu, S.; Sasi, B.; Jayakumar, T.; Baldev Raj

2010-01-01

Eddy current non-destructive evaluation (NDE) techniques find many applications during fabrication and in-service inspection of components made of stainless steel. In recent years, concurrent developments in electromagnetic field detection sensors such as giant magneto-resistive (GMR), giant-magneto impedance (GMI) and SQUIDs sensors, computers, microelectronics, and incorporating advanced signal and image processing techniques, have paved the way for enhancing the capabilities of existing eddy current (EC) techniques for examination of austenitic stainless steel (SS) plates, tubes and other geometries and several innovative methodologies have been developed. This paper highlights a few such applications in EC testing to austenitic stainless steel components used in fast reactors. (author)

HYDROïD humanoid robot head with perception and emotion capabilities :Modeling, Design and Experimental Results

Directory of Open Access Journals (Sweden)

Samer eAlfayad

2016-04-01

Full Text Available In the framework of the HYDROïD humanoid robot project, this paper describes the modeling and design of an electrically actuated head mechanism. Perception and emotion capabilities are considered in the design process. Since HYDROïD humanoid robot is hydraulically actuated, the choice of electrical actuation for the head mechanism addressed in this paper is justified. Considering perception and emotion capabilities leads to a total number of 15 degrees of freedom for the head mechanism which are split on four main sub-mechanisms: the neck, the mouth, the eyes and the eyebrows. Biological data and kinematics performances of human head are taken as inputs of the design process. A new solution of uncoupled eyes is developed to possibly address the master-slave process that links the human eyes as well as vergence capabilities. Modeling each sub-system is carried out in order to get equations of motion, their frequency responses and their transfer functions. The neck pitch rotation is given as a study example. Then, the head mechanism performances are presented through a comparison between model and experimental results validating the hardware capabilities. Finally, the head mechanism is integrated on the HYDROïD upper-body. An object tracking experiment coupled with emotional expressions is carried out to validate the synchronization of the eye rotations with the body motions.

Unsteady single-phase natural circulation flow mixing prediction using CATHARE three-dimensional capabilities

Energy Technology Data Exchange (ETDEWEB)

Salah, Anis Bousbia; Vlassenbroeck, Jacques [Bel V - Subsidiary of the Belgian Federal Agency for Nuclear Contro, Brussels (Belize)

2017-04-15

Coolant mixing under natural circulation flow regime constitutes a key parameter that may play a role in the course of an accidental transient in a nuclear pressurized water reactor. This issue has motivated some experimental investigations carried out within the OECD/NEA PKL projects. The aim was to assess the coolant mixing phenomenon in the reactor pressure vessel downcomer and the core lower plenum under several asymmetric steady and unsteady flow conditions, and to provide experimental data for code validations. Former studies addressed the mixing phenomenon using, on the one hand, one-dimensional computational approaches with cross flows that are not fully validated under transient conditions and, on the other hand, expensive computational fluid dynamic tools that are not always justified for large-scale macroscopic phenomena. In the current framework, an unsteady coolant mixing experiment carried out in the Rossendorf coolant mixing test facility is simulated using the three-dimensional porous media capabilities of the thermal–hydraulic system CATHARE code. The current study allows highlighting the current capabilities of these codes and their suitability for reproducing the main phenomena occurring during asymmetric transient natural circulation mixing conditions.

Experimental test of the background rejection, through imaging capability, of a highly segmented AGATA germanium detector

International Nuclear Information System (INIS)

Doncel, M.; Recchia, F.; Quintana, B.; Gadea, A.; Farnea, E.

2010-01-01

The development of highly segmented germanium detectors as well as the algorithms to identify the position of the interaction within the crystal opens the possibility to locate the γ-ray source using Compton imaging algorithms. While the Compton-suppression shield, coupled to the germanium detector in conventional arrays, works also as an active filter against the γ rays originated outside the target, the new generation of position sensitive γ-ray detector arrays has to fully rely on tracking capabilities for this purpose. In specific experimental conditions, as the ones foreseen at radioactive beam facilities, the ability to discriminate background radiation improves the sensitivity of the gamma spectrometer. In this work we present the results of a measurement performed at the Laboratori Nazionali di Legnaro (LNL) aiming the evaluation of the AGATA detector capabilities to discriminate the origin of the γ rays on an event-by-event basis. It will be shown that, exploiting the Compton scattering formula, it is possible to track back γ rays coming from different positions, assigning them to specific emitting locations. These imaging capabilities are quantified for a single crystal AGATA detector.

Experimental study on the supercritical startup and heat transport capability of a neon-charged cryogenic loop heat pipe

International Nuclear Information System (INIS)

Guo, Yuandong; Lin, Guiping; He, Jiang; Bai, Lizhan; Zhang, Hongxing; Miao, Jianyin

2017-01-01

Highlights: • A neon-charged CLHP integrated with a G-M cryocooler was designed and investigated. • The CLHP can realize the supercritical startup with an auxiliary heat load of 1.5 W. • Maximum heat transport capability of the CLHP was 4.5 W over a distance of 0.6 m. • There existed an optimum auxiliary heat load to expedite the supercritical startup. • There existed an optimum charged pressure to reach the largest heat transfer limit. - Abstract: Neon-charged cryogenic loop heat pipe (CLHP) can realize efficient cryogenic heat transport in the temperature range of 30–40 K, and promises great application potential in the thermal control of future space infrared exploration system. In this work, extensive experimental studies on the supercritical startup and heat transport capability of a neon-charged CLHP integrated with a G-M cryocooler were carried out, where the effects of the auxiliary heat load applied to the secondary evaporator and charged pressure of the working fluid were investigated. Experimental results showed that the CLHP could successfully realize the supercritical startup with an auxiliary heat load of 1.5 W, and there existed an optimum auxiliary heat load and charged pressure of the working fluid respectively, to achieve the maximum temperature drop rate of the primary evaporator during the supercritical startup. The CLHP could reach a maximum heat transport capability of 4.5 W over a distance of 0.6 m corresponding to the optimum charged pressure of the working fluid; however, the heat transport capability decreased with the increase of the auxiliary heat load. Furthermore, the inherent mechanisms responsible for the phenomena observed in the experiments were analyzed and discussed, to provide a better understanding from the theoretical view.

THE IDEA IS TO USEMODIS IN CONJUNCTION WITH THE CURRENT LIMITED LANDSAT CAPABILITY, COMMERCIAL SATELLITES, ANDUNMANNED AERIAL VEHICLES (UAV), IN A MULTI-STAGE APPROACH TO MEET EPA INFORMATION NEEDS.REMOTE SENSING OVERVIEW: EPA CAPABILITIES, PRIORITY AGENCY APPLICATIONS, SENSOR/AIRCRAFT CAPABILITIES, COST CONSIDERATIONS, SPECTRAL AND SPATIAL RESOLUTIONS, AND TEMPORAL CONSIDERATIONS

Science.gov (United States)

EPA remote sensing capabilities include applied research for priority applications and technology support for operational assistance to clients across the Agency. The idea is to use MODIS in conjunction with the current limited Landsat capability, commercial satellites, and Unma...

Fault Ride Through Capability Enhancement of a Large-Scale PMSG Wind System with Bridge Type Fault Current Limiters

Directory of Open Access Journals (Sweden)

ALAM, M. S.

2018-02-01

Full Text Available In this paper, bridge type fault current limiter (BFCL is proposed as a potential solution to the fault problems of permanent magnet synchronous generator (PMSG based large-scale wind energy system. As PMSG wind system is more vulnerable to disturbances, it is essential to guarantee the stability during severe disturbances by enhancing the fault ride through capability. BFCL controller has been designed to insert resistance and inductance during the inception of system disturbances in order to limit fault current. Constant capacitor voltage has been maintained by the grid voltage source converter (GVSC controller while current extraction or injection has been achieved by machine VSC (MVSC controller. Symmetrical and unsymmetrical faults have been applied in the system to show the effectiveness of the proposed BFCL solution. PMSG wind system, BFCL and their controllers have been implemented by real time hardware in loop (RTHIL setup with real time digital simulator (RTDS and dSPACE. Another significant feature of this work is that the performance of the proposed BFCL is compared with that of series dynamic braking resistor (SDBR. Comparative RTHIL implementation results show that the proposed BFCL is very efficient in improving system fault ride through capability by limiting the fault current and outperforms SDBR.

Experimental observations of stray current effects on steel fibres embedded in mortar

DEFF Research Database (Denmark)

Solgaard, A.O.S.; Carsana, M.; Geiker, M.R.

2013-01-01

It is known that stray direct current can cause corrosive damage over time to bar reinforced concrete, but knowledge on the consequences to steel fibre reinforced concrete is limited. This paper presents analyses and corresponding results from an experimental program (parametric study) investigat......It is known that stray direct current can cause corrosive damage over time to bar reinforced concrete, but knowledge on the consequences to steel fibre reinforced concrete is limited. This paper presents analyses and corresponding results from an experimental program (parametric study......) investigating the conditions required for current to be picked up by embedded steel fibres or reinforcement (rebars). The experiments showed that there is a clear ‘length effect’ related to the susceptibility of stray current being picked up by embedded steel (fibres or rebars): the shorter the reinforcement...

Currents, HF Radio-derived, SF Bay, 1 hr, Meridional, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the meridional component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

Currents, HF Radio-derived, SF Bay, 1 hr, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

Currents, HF Radio-derived, Bodega Bay, 1 hr, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

Developing sustainable business experimentation capability : A case study

NARCIS (Netherlands)

Weissbrod, Ilka; Bocken, N.M.P.

2017-01-01

This research paper shows how a firm pursues innovation activities for economic, social and environmental value creation in the context of time sensitivity. We make a conceptual link between lean startup thinking, triple bottom line value creation, and organizational capabilities. The case study

An Experimental Evaluation of Blockage Corrections for Current Turbines

Science.gov (United States)

Ross, Hannah; Polagye, Brian

2017-11-01

Flow confinement has been shown to significantly alter the performance of turbines that extract power from water currents. These performance effects are related to the degree of constraint, defined by the ratio of turbine projected area to channel cross-sectional area. This quantity is referred to as the blockage ratio. Because it is often desirable to adjust experimental observations in water channels to unconfined conditions, analytical corrections for both wind and current turbines have been derived. These are generally based on linear momentum actuator disk theory but have been applied to turbines without experimental validation. This work tests multiple blockage corrections on performance and thrust data from a cross-flow turbine and porous plates (experimental analogues to actuator disks) collected in laboratory flumes at blockage ratios ranging between 10 and 35%. To isolate the effects of blockage, the Reynolds number, Froude number, and submergence depth were held constant while the channel width was varied. Corrected performance data are compared to performance in a towing tank at a blockage ratio of less than 5%. In addition to examining the accuracy of each correction, underlying assumptions are assessed to determine why some corrections perform better than others. This material is based upon work supported by the National Science Foundation Graduate Research Fellowship Program under Grant No. DGE-1256082 and the Naval Facilities Engineering Command (NAVFAC).

Materials capability review Los Alamos National Laboratory, May 3-6, 2010

Energy Technology Data Exchange (ETDEWEB)

Taylor, Antoinette [Los Alamos National Laboratory

2010-01-01

The 2010 'Capability Review' process at LANL significantly differs from the Division reviews of prior years. The Capabilities being reviewed (some 4-8 per year) are deliberately chosen to be crosscutting over the Laboratory, and therefore will include not only several experimental, theoretical and simulation disciplines, but also contributions from multiple line organizations. This approach is consistent with the new Laboratory organizational structure, focusing on agile and integrated capabilities applied to present national security missions, and also nurtured to be available for rapid application to future missions. The overall intent is that the Committee assess the quality of the science, engineering, and technology identified in the agenda, and advise the LANS Board of Governors and Laboratory management. Specifically, the Committees will: (1) Assess the quality of science, technology and engineering within the Capability in the areas defined in the agenda. Identify issues to develop or enhance the core competencies within this capability. (2) Evaluate the integration of this capability across the Laboratory organizations that are listed in the agenda in terms of joint programs, projects, proposals, and/or publications. Describe the integration of this capability in the wider scientific community using the recognition as a leader within the community, ability to set research agendas, and attraction and retention of staff. (3) Assess the quality and relevance of this capability's science, technology and engineering contributions to current and emerging Laboratory programs, including Nuclear Weapons, Threat Reduction/Homeland Security, and Energy Security. (4) Advise the Laboratory Director/Principal Associate Director for Science, Technology and Engineering on the health of the Capability including the current and future (5 year) science, technology and engineering staff needs, mix of research and development activities, program opportunities

NGNP Data Management and Analysis System Analysis and Web Delivery Capabilities

Energy Technology Data Exchange (ETDEWEB)

Cynthia D. Gentillon

2011-09-01

Projects for the Very High Temperature Reactor (VHTR) Technology Development Office provide data in support of Nuclear Regulatory Commission licensing of the very high temperature reactor. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high-temperature and high-fluence environments. The NGNP Data Management and Analysis System (NDMAS) at the Idaho National Laboratory has been established to ensure that VHTR data are (1) qualified for use, (2) stored in a readily accessible electronic form, and (3) analyzed to extract useful results. This document focuses on the third NDMAS objective. It describes capabilities for displaying the data in meaningful ways and for data analysis to identify useful relationships among the measured quantities. The capabilities are described from the perspective of NDMAS users, starting with those who just view experimental data and analytical results on the INL NDMAS web portal. Web display and delivery capabilities are described in detail. Also the current web pages that show Advanced Gas Reactor, Advanced Graphite Capsule, and High Temperature Materials test results are itemized. Capabilities available to NDMAS developers are more extensive, and are described using a second series of examples. Much of the data analysis efforts focus on understanding how thermocouple measurements relate to simulated temperatures and other experimental parameters. Statistical control charts and correlation monitoring provide an ongoing assessment of instrument accuracy. Data analysis capabilities are virtually unlimited for those who use the NDMAS web data download capabilities and the analysis software of their choice. Overall, the NDMAS provides convenient data analysis and web delivery capabilities for studying a very large and rapidly increasing database of well-documented, pedigreed data.

Experimental typography : reviewing the modernist and the current approaches

OpenAIRE

Makal, Eray

1993-01-01

Ankara : The Department of Graphic Design and Institute of Fine Arts, Bilkent Univ., 1993. Thesis (Master's) -- Bilkent University, 1993. Includes bibliographical references leaves 65-66. The intention of this study is to evaluate the experimental typography within the history of graphic design by taking in consideration of two epochs. The Modernist and The Current. Makal, Eray M.S.

Ion extraction capabilities of two-grid accelerator systems

International Nuclear Information System (INIS)

Rovang, D.C.; Wilbur, P.J.

1984-02-01

An experimental investigation into the ion extraction capabilities of two-grid accelerator systems common to electrostatic ion thrusters is described. This work resulted in a large body of experimental data which facilitates the selection of the accelerator system geometries and operating parameters necessary to maximize the extracted ion current. Results suggest that the impingement-limited perveance is not dramatically affected by reductions in screen hole diameter to 0.5 mm. Impingement-limited performance is shown to depend most strongly on grid separation distance, accelerator hole diameter ratio, the discharge-to-total accelerating voltage ratio, and the net-to-total accelerating voltage ratio. Results obtained at small grid separation ratios suggest a new grid operating condition where high beam current per hole levels are achieved at a specified net accelerating voltage. It is shown that this operating condition is realized at an optimum ratio of net-to-total accelerating voltage ratio which is typically quite high. The apparatus developed for this study is also shown to be well suited measuring the electron backstreaming and electrical breakdown characteristics of two-grid accelerator systems

Space Logistics: Launch Capabilities

Science.gov (United States)

Furnas, Randall B.

1989-01-01

The current maximum launch capability for the United States are shown. The predicted Earth-to-orbit requirements for the United States are presented. Contrasting the two indicates the strong National need for a major increase in Earth-to-orbit lift capability. Approximate weights for planned payloads are shown. NASA is studying the following options to meet the need for a new heavy-lift capability by mid to late 1990's: (1) Shuttle-C for near term (include growth versions); and (2) the Advanced Lauching System (ALS) for the long term. The current baseline two-engine Shuttle-C has a 15 x 82 ft payload bay and an expected lift capability of 82,000 lb to Low Earth Orbit. Several options are being considered which have expanded diameter payload bays. A three-engine Shuttle-C with an expected lift of 145,000 lb to LEO is being evaluated as well. The Advanced Launch System (ALS) is a potential joint development between the Air Force and NASA. This program is focused toward long-term launch requirements, specifically beyond the year 2000. The basic approach is to develop a family of vehicles with the same high reliability as the Shuttle system, yet offering a much greater lift capability at a greatly reduced cost (per pound of payload). The ALS unmanned family of vehicles will provide a low end lift capability equivalent to Titan IV, and a high end lift capability greater than the Soviet Energia if requirements for such a high-end vehicle are defined.In conclusion, the planning of the next generation space telescope should not be constrained to the current launch vehicles. New vehicle designs will be driven by the needs of anticipated heavy users.

Human Exploration Systems and Mobility Capability Roadmap Progress Review

Science.gov (United States)

Culbert, Chris; Taylor, Jeff

2005-01-01

Contents include the following: Capability Roadmap Team. Capability Description and Capability Breakdown Structure. Benefits of the Human Systems and Mobility Capability. Roadmap Process and Approach. Drivers and Assumptions for the whole team. Current State-of-the-Art, Assumptions and Requirements will be covered in the appropriate sections. Capability Presentations by Leads under Roadmap (Repeated for each capability under roadmap). Capability Description, Benefits, Current State-of-the-Art. Capability Requirements and Assumptions. Roadmap for Capability. Capability Readiness Level. Technology Readiness Level. Figures of Merit. Summary of Top Level Capability. Significant Technical Challenges. Summary and Forward Work.

Predictive digital peak current mode controller for DC-DC converters capable of operating over the full 0-100% duty cycle range

DEFF Research Database (Denmark)

Andersen, Karsten Holm; Nymand, Morten

2017-01-01

) and discontinuous conduction mode (DCM) and supports high switching frequencies even with low cost A/D converters. The proposed controller is implemented in a Field Programmable Gate Array (FPGA) to control a 450 W buck converter and the experimental results verify the controller's capability to operate in the full...

Experimental study of gas-cooled current leads for superconducting magnets

International Nuclear Information System (INIS)

Warren, R.P.

1978-04-01

Design details and experimental test results from several design variations of the gas-cooled, copper current leads used in conjunction with the superconducting dipole magnets for ESCAR (Experimental Superconducting Accelerator Ring) are reported. Thermal acoustic oscillations, which were experienced with an initial design, were eliminated in subsequent designs by a reduction of the hydraulic diameter. The occurrence of these oscillations is in general agreement with the stability analysis of Rott but the observed gas flow dependence is not in agreement with some other recently reported results for leads operated supercritical phase coolant. An empirically determined correlation was obtained by plotting lead resistance vs. enthalpy gain of the coolant gas. The resulting family of curves can be reduced to a single line on a plot of effective resistivity vs. the product of current and cross-sectional area divided by the product of the square of the mass flow of the coolant and the lead length. This correlation, which should be applicable to other designs of copper current leads in which ideal heat transfer to the coolant gas is approached, predicts that the enthalpy gain of the coolant, and therefore the peak lead temperature, is proportional to the cube of the ratio of current to coolant mass flow. The effective value of the strongly temperature-dependent kinematic viscosity of the coolant gas was found to vary linearly with the effective resistivity of the lead

Model-Based Military Scenario Management for Defence Capability

National Research Council Canada - National Science Library

Gori, Ronnie; Chen, Pin; Pozgay, Angela

2004-01-01

.... This paper describes initial work towards the development of an information model that links scenario and capability related information, and the results of capability analysis and experimentation...

Currents, HF Radio-derived, SF Bay Outlet, 1 hr, Meridional, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the meridional component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

Technical Study on Improvement of Endurance Capability of Limit Short-circuit Current of Charge Control SMART Meter

Science.gov (United States)

Li, W. W.; Du, Z. Z.; Yuan, R. m.; Xiong, D. Z.; Shi, E. W.; Lu, G. N.; Dai, Z. Y.; Chen, X. Q.; Jiang, Z. Y.; Lv, Y. G.

2017-10-01

Smart meter represents the development direction of energy-saving smart grid in the future. The load switch, one of the core parts of smart meter, should be of high reliability, safety and endurance capability of limit short-circuit current. For this reason, this paper discusses the quick simulation of relationship between attraction and counterforce of load switch without iteration, establishes dual response surface model of attraction and counterforce and optimizes the design scheme of load switch for charge control smart meter, thus increasing electromagnetic attraction and spring counterforce. In this way, this paper puts forward a method to improve the withstand capacity of limit short-circuit current.

ADVANCED SIMULATION CAPABILITY FOR ENVIRONMENTAL MANAGEMENT- CURRENT STATUS AND PHASE II DEMONSTRATION RESULTS

Energy Technology Data Exchange (ETDEWEB)

Seitz, R.

2013-02-26

The U.S. Department of Energy (USDOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Toolsets and High-Performance Computing (HPC) Multiprocess Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, toolsets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial toolsets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations

Quantifying the Global Fresh Water Budget: Capabilities from Current and Future Satellite Sensors

Science.gov (United States)

Hildebrand, Peter; Zaitchik, Benjamin

2007-01-01

The global water cycle is complex and its components are difficult to measure, particularly at the global scales and with the precision needed for assessing climate impacts. Recent advances in satellite observational capabilities, however, are greatly improving our knowledge of the key terms in the fresh water flux budget. Many components of the of the global water budget, e.g. precipitation, atmospheric moisture profiles, soil moisture, snow cover, sea ice are now routinely measured globally using instruments on satellites such as TRMM, AQUA, TERRA, GRACE, and ICESat, as well as on operational satellites. New techniques, many using data assimilation approaches, are providing pathways toward measuring snow water equivalent, evapotranspiration, ground water, ice mass, as well as improving the measurement quality for other components of the global water budget. This paper evaluates these current and developing satellite capabilities to observe the global fresh water budget, then looks forward to evaluate the potential for improvements that may result from future space missions as detailed by the US Decadal Survey, and operational plans. Based on these analyses, and on the goal of improved knowledge of the global fresh water budget under the effects of climate change, we suggest some priorities for the future, based on new approaches that may provide the improved measurements and the analyses needed to understand and observe the potential speed-up of the global water cycle under the effects of climate change.

Improvements in TREAT hodoscope fuel-motion capabilities

International Nuclear Information System (INIS)

Fink, C.L.; Boyar, R.E.; Eichholz, J.J.; DeVolpi, A.

1982-01-01

The fast-neutron detection system of the hadoscope has been a major ingredient in the success of the hodoscope as a fuel-motion monitoring device. While the original Hornyak-button detector system has met most of the current fuel-motion needs, the more stringent requirements of improved reactor-safety codes, and of new experimental test facilities necessitate improved detection capabilities. Development efforts have centered on three areas: the construction of an array of proton-recoil proportional counters to be used in conjunction with the Hornyak-button detectors, the upgrading of the Hornyak-button detectors to increase linearity and signal-to-background ratio, and the intercalibration of detectors using a modified horizontal and a new vertical scan system

Radiography Capabilities for Matter-Radiation Interactions in Extremes

Energy Technology Data Exchange (ETDEWEB)

Walstrom, Peter Lowell [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Garnett, Robert William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chapman, Catherine A. B [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Salazar, Harry Richard [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Otoole, Joseph Alfred [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Barber, Ronald L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Gomez, Tony Simon [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-04-28

The Matter-Radiation Interactions in Extremes (MaRIE) experimental facility will be used to discover and design the advanced materials needed to meet 21st century national security and energy security challenges. This new facility will provide the new tools scientists need to develop next-generation materials that will perform predictably and on-demand for currently unattainable lifetimes in extreme environments. The MaRIE facility is based on upgrades to the existing LANSCE 800-MeV proton linac and a new 12-GeV electron linac and associated X-ray FEL to provide simultaneous multiple probe beams, and new experimental areas. In addition to the high-energy photon probe beam, both electron and proton radiography capabilities will be available at the MaRIE facility. Recently, detailed radiography system studies have been performed to develop conceptual layouts of high-magnification electron and proton radiography systems that can meet the experimental requirements for the expected first experiments to be performed at the facility. A description of the radiography systems, their performance requirements, and a proposed facility layout are presented.

Field- and current-driven domain wall dynamics: An experimental picture

International Nuclear Information System (INIS)

Beach, G.S.D.; Knutson, C.; Tsoi, M.; Erskine, J.L.

2007-01-01

Field- and current-driven domain wall velocities are measured and discussed in terms of existing spin-torque models. A reversal in the roles of adiabatic and non-adiabatic spin-torque is shown to arise in those models below and above Walker breakdown. The measured dependence of velocity on current is the same in both regimes, indicating both spin-torque components have similar magnitude. However, the models on which these conclusions are based have serious quantitative shortcomings in describing the observed field-driven wall dynamics, for which they were originally developed. Hence, the applicability of simple one-dimensional models to most experimental conditions may be limited

Current transport modeling and experimental study of THz room temperature ballistic deflection transistors

Energy Technology Data Exchange (ETDEWEB)

Kaushal, Vikas; Margala, Martin [Department of Electrical and Computer Engineering, University of Massachusetts Lowell, MA, 01854 (United States); Yu Qiaoyan; Ampadu, Paul; Guarino, Gregg; Sobolewski, Roman, E-mail: vikas_kaushal@student.uml.ed [Department of Electrical and Computer Engineering, University of Rochester, NY, 14627 (United States)

2009-11-15

In this paper, two different theoretical models, Comsol Multiphysics{sup TM} (a Finite Element Analysis tool), and a field solver Atlas/Blaze from Silvaco, are compared qualitatively to study the effect of the deflector position, its size and electric field on the charge transport and its distribution along the channel, resulting in current outputs and leakages in ballistic deflection transistors (BDT). Silvaco simulations and experimental results were then used to study the lateral charge transport as a result of variation in electric field distribution, which controls the charge current along the channel in BDT. The electric field dependence of gain is also studied with experimental and theoretical results.

Current transport modeling and experimental study of THz room temperature ballistic deflection transistors

International Nuclear Information System (INIS)

Kaushal, Vikas; Margala, Martin; Yu Qiaoyan; Ampadu, Paul; Guarino, Gregg; Sobolewski, Roman

2009-01-01

In this paper, two different theoretical models, Comsol Multiphysics TM (a Finite Element Analysis tool), and a field solver Atlas/Blaze from Silvaco, are compared qualitatively to study the effect of the deflector position, its size and electric field on the charge transport and its distribution along the channel, resulting in current outputs and leakages in ballistic deflection transistors (BDT). Silvaco simulations and experimental results were then used to study the lateral charge transport as a result of variation in electric field distribution, which controls the charge current along the channel in BDT. The electric field dependence of gain is also studied with experimental and theoretical results.

Weak interactions and exchange currents in light nuclei. Theoretical and experimental aspects

International Nuclear Information System (INIS)

Guichon, P.

1980-01-01

The influence of meson exchange currents in the nuclear weak interaction is investigated theoretically and experimentally. The hypothesis of current algebra and partial conservation of axial current are used, through Adler-Dothan theorem, to derive the one pion exchange correction to the impulse approximation. Calculations are performed for partial transitions in the 1p-shell nuclei and in 16 O. The corrections are generally small except for the (0 + →0 - ) transition in 16 O where the large correction to the time component of the axial current can show up, due to selection rules. The measurement of the muon capture rate for this transition is described and an interpretation in term of exchange currents is proposed [fr

Current and Future Research at DANCE

Science.gov (United States)

Jandel, M.; Baramsai, B.; Bredeweg, T. A.; Couture, A.; Hayes, A.; Kawano, T.; Mosby, S.; Rusev, G.; Stetcu, I.; Taddeucci, T. N.; Talou, P.; Ullmann, J. L.; Walker, C. L.; Wilhelmy, J. B.

2015-05-01

An overview of the current experimental program on measurements of neutron capture and neutron induced fission at the Detector for Advanced Neutron Capture Experiments (DANCE) is presented. Three major projects are currently under way: 1) high precision measurements of neutron capture cross sections on Uranium isotopes, 2) research aimed at studies of the short-lived actinide isomer production in neutron capture on 235U and 3) measurements of correlated data of fission observables. New projects include developments of auxiliary detectors to improve the capability of DANCE. We are building a compact, segmented NEUtron detector Array at DANCE (NEUANCE), which will be installed in the central cavity of the DANCE array. It will provide experimental information on prompt fission neutrons in coincidence with the prompt fission gamma-rays measured by 160 BaF2 crystals of DANCE. Unique correlated data will be obtained for neutron capture and neutron-induced fission using the DANCE-NEUANCE experimental set up in the future.

Experimentally determined profiles of fast wave current drive on DIII-D

International Nuclear Information System (INIS)

Forest, C.B.; Petty, C.C.; Baity, F.W.; Chiu, S.C.; deGrassie, J.S.; Groebner, R.J.; Ikezi, H.; Jaeger, E.F.; Kupfer, K.; Murakami, M.; Pinsker, R.I.; Prater, R.; Rice, B.W.; Wade, M.R.; Whyte, D.G.

1996-01-01

Profiles of non-inductive current driven by fast waves have been determined for reversed-shear DIII-D discharges. Both the current profile and toroidal electric field profile are determined from time sequences of equilibrium reconstructions [C. B. Forest et al., Phys. Rev. Lett. 73, 2224 (1994)]. Using this information, the measured current profile has been separated into inductive and non-inductive portions. By comparing similar discharges with co and counter antenna phasings and similar fast wave power, the portion of the total non-inductive current driven by fast waves was determined. The experimentally determined profiles of FWCD are in general agreement with theoretical predictions. Specifically, 135 kA was driven by 1.4 MW of rf power with a profile peaked inside ρ=2. copyright 1996 American Institute of Physics

DDP-516 Computer Graphics System Capabilities

Science.gov (United States)

1972-06-01

This report describes the capabilities of the DDP-516 Computer Graphics System. One objective of this report is to acquaint DOT management and project planners with the system's current capabilities, applications hardware and software. The Appendix i...

Experimental observation of current generation by asymmetrical heating of ions in a tokamak plasma

International Nuclear Information System (INIS)

Gahl, J.; Ishihara, O.; Wong, K.L.; Kristiansen, M.; Hagler, M.

1986-01-01

The first experimental observation of current generation by asymmetrical heating of ions is reported. Ions were asymmetrically heated by a unidirectional fast Alfven wave launched by a slow wave antenna inside a tokamak. Current generation was detected by measuring the asymmetry of the toroidal plasma current with probes at the top and bottom of the toroidal plasma column

Review of current capabilities for the measurement of stress, displacement, and in situ deformation modulus

International Nuclear Information System (INIS)

Schrauf, T.W.; Pratt, H.R.

1979-12-01

Current capabilities for the measurement of stress, displacement, and in situ deformation modulus in rock masses are reviewed as to their accuracy, sensitivity, advantages, and limitations. Consideration is given to both the instruments themselves and the measurement technique. Recommendations concerning adaptation of existing measurement techniques to repository monitoring are also discussed. These recommendations include: (1) development of a modified borehole deformation gage with improved long-term stability and reliability and reduced thermal sensitivity; (2) development of a downhole transducer type of extensometer; (3) development of a rigid inclusion type gage; (4) development of an improved vibrating wire stressmeter with greater accuracy and simplified calibration and installation requirements; and (5) modification of standard rod extensometers to improve their sensitivity

Advanced Simulation Capability for Environmental Management - Current Status and Phase II Demonstration Results - 13161

Energy Technology Data Exchange (ETDEWEB)

Seitz, Roger R.; Flach, Greg [Savannah River National Laboratory, Savannah River Site, Bldg 773-43A, Aiken, SC 29808 (United States); Freshley, Mark D.; Freedman, Vicky; Gorton, Ian [Pacific Northwest National Laboratory, MSIN K9-33, P.O. Box 999, Richland, WA 99352 (United States); Dixon, Paul; Moulton, J. David [Los Alamos National Laboratory, MS B284, P.O. Box 1663, Los Alamos, NM 87544 (United States); Hubbard, Susan S.; Faybishenko, Boris; Steefel, Carl I.; Finsterle, Stefan [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, MS 50B-4230, Berkeley, CA 94720 (United States); Marble, Justin [Department of Energy, 19901 Germantown Road, Germantown, MD 20874-1290 (United States)

2013-07-01

The U.S. Department of Energy (US DOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Tool-sets and High-Performance Computing (HPC) Multi-process Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial tool-sets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations

Advanced Simulation Capability for Environmental Management - Current Status and Phase II Demonstration Results - 13161

International Nuclear Information System (INIS)

Seitz, Roger R.; Flach, Greg; Freshley, Mark D.; Freedman, Vicky; Gorton, Ian; Dixon, Paul; Moulton, J. David; Hubbard, Susan S.; Faybishenko, Boris; Steefel, Carl I.; Finsterle, Stefan; Marble, Justin

2013-01-01

The U.S. Department of Energy (US DOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Tool-sets and High-Performance Computing (HPC) Multi-process Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial tool-sets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations

Theoretical and experimental studies on ionic currents in nanopore-based biosensors.

Science.gov (United States)

Liu, Lei; Li, Chu; Ma, Jian; Wu, Yingdong; Ni, Zhonghua; Chen, Yunfei

2014-12-01

Novel generation of analytical technology based on nanopores has provided possibilities to fabricate nanofluidic devices for low-cost DNA sequencing or rapid biosensing. In this paper, a simplified model was suggested to describe DNA molecule's translocation through a nanopore, and the internal potential, ion concentration, ionic flowing speed and ionic current in nanopores with different sizes were theoretically calculated and discussed on the basis of Poisson-Boltzmann equation, Navier-Stokes equation and Nernst-Planck equation by considering several important parameters, such as the applied voltage, the thickness and the electric potential distributions in nanopores. In this way, the basic ionic currents, the modulated ionic currents and the current drops induced by translocation were obtained, and the size effects of the nanopores were carefully compared and discussed based on the calculated results and experimental data, which indicated that nanopores with a size of 10 nm or so are more advantageous to achieve high quality ionic current signals in DNA sensing.

Overview of current RFSP-code capabilities for CANDU core analysis

International Nuclear Information System (INIS)

Rouben, B.

1996-01-01

RFSP (Reactor Fuelling Simulation Program) is the major finite-reactor computer code in use at the Atomic Energy of Canada Limited for the design and analysis of CANDU reactor cores. An overview is given of the major computational capabilities available in RFSP. (author) 11 refs., 29 figs

Experimental study of collective effects in BEP storage ring with high stored current

International Nuclear Information System (INIS)

Danilov, V.; Koop, I.; Lysenko, A.; Militsyn, B.; Nesterenko, I.; Perevedentsev, E.; Pozdeev, E.; Ptitsin, V.; Shatunov, Yu.; Vasserman, I.

1993-01-01

The results of extensive investigation of beam dynamics with high current in BEP booster are presented. Strong bunch lengthening due to the potential well distortion by the inductive impedance was observed on the background of the multiple intrabeam scattering and of the ion accumulation (in the e - beam). The octupole and sextupole corrections enabled control of collective damping of the head-tail modes. Fast damping is also observed at zero chromaticity, this is attributed to the injection kickers acting as transmission lines. The proper tuning of the nonlinearity corrections cures the transverse instabilities and enables capability to store up to 0.8A current in a single bunch

Networking capability and new product development

NARCIS (Netherlands)

Mu, J.; Di Benedetto, A.C.

2012-01-01

Current research on network theory remains largely focused on structures and outcomes without exploring the capability that firms need to build efficient and effective networks to their advantage. In this paper, we take a networking capability view in studying inter-firm relationships. We assume

Experimental study on the 300W class planar type solid oxide fuel cell stack: Investigation for appropriate fuel provision control and the transient capability of the cell performance

International Nuclear Information System (INIS)

Komatsu, Y; Brus, G; Szmyd, J S; Kimijima, S

2012-01-01

The present paper reports the experimental study on the dynamic behavior of a solid oxide fuel cell (SOFC). The cell stack consists of planar type cells with standard power output 300W. A Major subject of the present study is characterization of the transient response to the electric current change, assuming load-following operation. The present studies particularly focus on fuel provision control to the load change. Optimized fuel provision improves power generation efficiency. However, the capability of SOFC must be restricted by a few operative parameters. Fuel utilization factor, which is defined as the ratio of the consumed fuel to the supplied fuel is adopted for a reference in the control scheme. The fuel flow rate was regulated to keep the fuel utilization at 50%, 60% and 70% during the current ramping. Lower voltage was observed with the higher fuel utilization, but achieved efficiency was higher. The appropriate mass flow control is required not to violate the voltage transient behavior. Appropriate fuel flow manipulation can contribute to moderate the overshoot on the voltage that may appear to the current change. The overshoot on the voltage response resulted from the gradual temperature behavior in the SOFC stack module.

Experimental study on the 300W class planar type solid oxide fuel cell stack: Investigation for appropriate fuel provision control and the transient capability of the cell performance

Science.gov (United States)

Komatsu, Y.; Brus, G.; Kimijima, S.; Szmyd, J. S.

2012-11-01

The present paper reports the experimental study on the dynamic behavior of a solid oxide fuel cell (SOFC). The cell stack consists of planar type cells with standard power output 300W. A Major subject of the present study is characterization of the transient response to the electric current change, assuming load-following operation. The present studies particularly focus on fuel provision control to the load change. Optimized fuel provision improves power generation efficiency. However, the capability of SOFC must be restricted by a few operative parameters. Fuel utilization factor, which is defined as the ratio of the consumed fuel to the supplied fuel is adopted for a reference in the control scheme. The fuel flow rate was regulated to keep the fuel utilization at 50%, 60% and 70% during the current ramping. Lower voltage was observed with the higher fuel utilization, but achieved efficiency was higher. The appropriate mass flow control is required not to violate the voltage transient behavior. Appropriate fuel flow manipulation can contribute to moderate the overshoot on the voltage that may appear to the current change. The overshoot on the voltage response resulted from the gradual temperature behavior in the SOFC stack module.

Experimental investigation of powerful pulse current generators based on capacitive storage and explosive magnetic generators

Science.gov (United States)

Shurupov, A. V.; Zavalova, V. E.; Kozlov, A. V.; Shurupov, M. A.; Povareshkin, M. N.; Kozlov, A. A.; Shurupova, N. P.

2018-01-01

Experimental models of microsecond duration powerful generators of current pulses on the basis of explosive magnetic generators and voltage impulse generator have been developed for the electromagnetic pulse effects on energy facilities to verify their stability. Exacerbation of voltage pulse carried out through the use of electro explosive current interrupter made of copper wires with diameters of 80 and 120 μm. Experimental results of these models investigation are represented. Voltage fronts about 100 ns and the electric field strength of 800 kV/m are registered.

Electro-Thermal-Mechanical Simulation Capability Final Report

International Nuclear Information System (INIS)

White, D

2008-01-01

such as magnetic flux compression generators and railguns. This project compliments ongoing DNT projects that have an experimental emphasis. Our research efforts have been encapsulated in the Diablo and ALE3D simulation codes. This new ETM capability already has both internal and external users, and has spawned additional research in plasma railgun technology. By developing this capability Engineering has become a world-leader in ETM design, analysis, and simulation. This research has positioned LLNL to be able to compete for new business opportunities with the DoD in the area of railgun design. We currently have a three-year $1.5M project with the Office of Naval Research to apply our ETM simulation capability to railgun bore life issues and we expect to be a key player in the railgun community

High Accuracy Beam Current Monitor System for CEBAF'S Experimental Hall A

International Nuclear Information System (INIS)

J. Denard; A. Saha; G. Lavessiere

2001-01-01

CEBAF accelerator delivers continuous wave (CW) electron beams to three experimental Halls. In Hall A, all experiments require continuous, non-invasive current measurements and a few experiments require an absolute accuracy of 0.2 % in the current range from 1 to 180 (micro)A. A Parametric Current Transformer (PCT), manufactured by Bergoz, has an accurate and stable sensitivity of 4 (micro)A/V but its offset drifts at the muA level over time preclude its direct use for continuous measurements. Two cavity monitors are calibrated against the PCT with at least 50 (micro)A of beam current. The calibration procedure suppresses the error due to PCT's offset drifts by turning the beam on and off, which is invasive to the experiment. One of the goals of the system is to minimize the calibration time without compromising the measurement's accuracy. The linearity of the cavity monitors is a critical parameter for transferring the accurate calibration done at high currents over the whole dynamic range. The method for measuring accurately the linearity is described

Resource-Based Capability on Development Knowledge Management Capabilities of Coastal Community

Science.gov (United States)

Teniwut, Roberto M. K.; Hasyim, Cawalinya L.; Teniwut, Wellem A.

2017-10-01

Building sustainable knowledge management capabilities in the coastal area might face a whole new challenge since there are many intangible factors involved from openness on new knowledge, access and ability to use the latest technology to the various local wisdom that still in place. The aimed of this study was to identify and analyze the resource-based condition of coastal community in this area to have an empirical condition of tangible and intangible infrastructure on developing knowledge management capability coastal community in Southeast Maluku, Indonesia. We used qualitative and quantitative analysis by depth interview and questionnaire for collecting the data with multiple linear regression as our analysis method. The result provided the information on current state of resource-based capability of a coastal community in this Southeast Maluku to build a sustainability model of knowledge management capabilities especially on utilization marine and fisheries resources. The implication of this study can provide an empirical information for government, NGO and research institution to dictate on how they conducted their policy and program on developing coastal community region.

Towards a dynamic concept of alliance capability

OpenAIRE

SLUYTS, Kim; MARTENS, Rudy; MATTHYSSENS, Paul

2008-01-01

This paper has a threefold purpose. First, we offer a literature review on alliance capability based on strategic and competence based management literature. Second, we extend existing literature on alliance capability by breaking this concept down into five sub capabilities, which are each linked to a stage of the alliance life cycle. Finally, we suggest how firms can support these capabilities through structural, technological and people-related tools and techniques. We argue that current l...

Outcomes of Domestic Standard Problem-03 : Scaling Capability of Facility Data

Energy Technology Data Exchange (ETDEWEB)

Park, Yusun; Youn, Bumsu; Lee, Seung-won; Kim, Won-tae; Kang, Kyoung-ho; Choi, Ki-yong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

The Domestic Standard Problem (DSP) previous two DSPs provided good research opportunities to many nuclear organizations to understand the capability of the current system-scale safety analysis codes and to find a way for further code development area. Thus, the third DSP program was launched in the 2nd half of the year 2012. As the third DSP exercise (DSP-03), a double-ended guillotine break of the main steam line at an 8% power without loss of off-site power (LOOP) was decided a target scenario. Seventeen domestic organizations joined this DSP exercise. This DSP exercise was performed in an open calculation environment similar to the previous ones. In the present DSP-03, taking into accounts the different levels of code experiences and expertise, three sub-topics were suggested by operating agency. Among them, the investigation on scaling capability of facility data which was the topic of Group A will be discussed in this paper. Agreed participants should perform two calculations with the ATLAS model and the APR1400 model. By comparing major and detailed local parameters from both calculation models, scaling capability of the facility data was investigated. The 38.6 mm MSLB in ATLAS test facility was calculated using SPACE and MARS-KS code. To analyze the effect of scaling on the system behavior, MSLB in APR-1400 was also simulated in this study and following results were obtained. - The code predicted appropriately the overall MSLB experimental data obtained from ATLAS test facility. - The break flow calculated by code was lower than that of experimental data. - And the difference between calculated value and measured value was attributed to the measurement of mass from break flow. - The temperatures of core inlet and outlet of ATLAS test facility were predicted lower than those of experimental data.

Qualitative assessment of the fission product release capability of ELOCA.Mk5

International Nuclear Information System (INIS)

Klein, M.E.; Carlucci, L.N.; Arimescu, V.I.

1995-01-01

A qualitative assessment of the fission product release capability of the ELOCA.Mk5 computer code was performed by simulating two transients from the sweep-gas experiment, FIO-133. Improved agreement between calculated and experimental trends in release was obtained by applying an interface pressure stress component to the pellet center. As well, results show that the current system for defining the reference temperature distribution for the thermal stress component is not always realistic. These results are being used in the development of a new, mechanistic pellet stress model. (author)

Analytical Chemistry Core Capability Assessment - Preliminary Report

International Nuclear Information System (INIS)

Barr, Mary E.; Farish, Thomas J.

2012-01-01

The concept of 'core capability' can be nebulous one. Even at a fairly specific level, where core capability equals maintaining essential services, it is highly dependent upon the perspective of the requestor. Samples are submitted to analytical services because the requesters do not have the capability to conduct adequate analyses themselves. Some requests are for general chemical information in support of R and D, process control, or process improvement. Many analyses, however, are part of a product certification package and must comply with higher-level customer quality assurance requirements. So which services are essential to that customer - just those for product certification? Does the customer also (indirectly) need services that support process control and improvement? And what is the timeframe? Capability is often expressed in terms of the currently utilized procedures, and most programmatic customers can only plan a few years out, at best. But should core capability consider the long term where new technologies, aging facilities, and personnel replacements must be considered? These questions, and a multitude of others, explain why attempts to gain long-term consensus on the definition of core capability have consistently failed. This preliminary report will not try to define core capability for any specific program or set of programs. Instead, it will try to address the underlying concerns that drive the desire to determine core capability. Essentially, programmatic customers want to be able to call upon analytical chemistry services to provide all the assays they need, and they don't want to pay for analytical chemistry services they don't currently use (or use infrequently). This report will focus on explaining how the current analytical capabilities and methods evolved to serve a variety of needs with a focus on why some analytes have multiple analytical techniques, and what determines the infrastructure for these analyses. This information will be

Liberalism, Humanism, and Feminism in Nussbaum's Capabilities ...

African Journals Online (AJOL)

A purely theoretical analysis of Martha Nussbaum's basis of the capabilities ... Since even a capabilities approach rooted in feminist justice is itself radical and must ... rhetoric of sex and social justice that has already been embraced by current

Experimental and Numerical Investigation of Local Scour Around Submarine Piggyback Pipeline Under Steady Current

Science.gov (United States)

Zhao, Enjin; Shi, Bing; Qu, Ke; Dong, Wenbin; Zhang, Jing

2018-04-01

As a new type of submarine pipeline, the piggyback pipeline has been gradually adopted in engineering practice to enhance the performance and safety of submarine pipelines. However, limited simulation work and few experimental studies have been published on the scour around the piggyback pipeline under steady current. This study numerically and experimentally investigates the local scour of the piggyback pipe under steady current. The influence of prominent factors such as pipe diameter, inflow Reynolds number, and gap between the main and small pipes, on the maximum scour depth have been examined and discussed in detail. Furthermore, one formula to predict the maximum scour depth under the piggyback pipeline has been derived based on the theoretical analysis of scour equilibrium. The feasibility of the proposed formula has been effectively calibrated by both experimental data and numerical results. The findings drawn from this study are instructive in the future design and application of the piggyback pipeline.

Development of Experimental Icing Simulation Capability for Full-Scale Swept Wings: Hybrid Design Process, Years 1 and 2

Science.gov (United States)

Fujiwara, Gustavo; Bragg, Mike; Triphahn, Chris; Wiberg, Brock; Woodard, Brian; Loth, Eric; Malone, Adam; Paul, Bernard; Pitera, David; Wilcox, Pete;

Study on Application of New Approach of Fault Current Limiters in Fault Ride through Capability Improvement of DFIG Based Wind Turbine

DEFF Research Database (Denmark)

Naderi, Seyed Behzad; Davari, Pooya; Zhou, Dao

2018-01-01

Due to salient advantages, Doubly-Fed Induction Generator (DFIG) has more application in power network compared to Fixed Speed Wind Turbine. Because of employing back-to-back converters, one of the important studies regarding new grid code requirements is Fault Ride-Through (FRT) capability....... The proposed FCL can insert a controllable resistance in fault current pass to not only restrict fault current level and compensate voltage sag in the stator but also consume pre-fault output active power of the DFIG regarding wind speed variation. Simulation results and analytics are presented to prove...

Designing high-order power-source synchronous current converters for islanded and grid-connected microgrids

DEFF Research Database (Denmark)

Ashabani, Mahdi; Gooi, Hoay Beng; Guerrero, Josep M.

2018-01-01

This paper deals with development of a versatile and compact control strategy for voltage source converters in grid-connected and islanded microgrids using synchronous current converters technology. The key feature is its new integrated high-order controller/synchronizer with applicability to both...... and automated current-based grid synchronization. Moreover, the controller realizes a power-source current-controlled microgrid with minimum control loops, as compared to widely adopted voltage controlled microgrids in the literature, with advantages such as fault-ride-through and inherent droop-less power...... sharing capabilities. Adaptive current-based synchronization and smooth switching to islanding mode provides high flexibility, reliability and only-plug operation capability. Extensive simulation and experimental results are presented to demonstrate performance of the proposed control and management...

First experimental results with the Current Limit Avoidance System at the JET tokamak

Energy Technology Data Exchange (ETDEWEB)

De Tommasi, G. [Associazione EURATOM-ENEA-CREATE, Università di Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); Galeani, S. [Dipartimento di Informatica, Sistemi e Produzione, Università di Roma, Tor Vergata, Rome (Italy); Jachmich, S. [Association EURATOM-Belgian State, Koninklijke Militaire School - Ecole Royale Militaire, B-1000 Brussels (Belgium); Joffrin, E. [IRFM-CEA, Centre de Cadarache, 13108 Saint-paul-lez-Durance (France); Lennholm, M. [EFDA Close Support Unit, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); European Commission, B-1049 Brussels (Belgium); Lomas, P.J. [Euratom-CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Neto, A.C. [Associazione EURATOM-IST, Instituto de Plasmas e Fusao Nuclear, IST, 1049-001 Lisboa (Portugal); Maviglia, F. [Associazione EURATOM-ENEA-CREATE, Via Claudio 21, 80125 Napoli (Italy); McCullen, P. [Euratom-CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Pironti, A. [Associazione EURATOM-ENEA-CREATE, Università di Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); Rimini, F.G. [Euratom-CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Sips, A.C.C. [European Commission, B-1049 Brussels (Belgium); Varano, G.; Vitelli, R. [Dipartimento di Informatica, Sistemi e Produzione, Università di Roma, Tor Vergata, Rome (Italy); Zaccarian, L. [CNRS, LAAS, 7 Avenue du Colonel Roche, F-31400 Toulouse (France); Universitè de Toulouse, LAAS, F-31400 Toulouse (France)

2013-06-15

The Current Limit Avoidance System (CLA) has been recently deployed at the JET tokamak to avoid current saturations in the poloidal field (PF) coils when the eXtreme Shape Controller is used to control the plasma shape. In order to cope with the current saturation limits, the CLA exploits the redundancy of the PF coils system to automatically obtain almost the same plasma shape using a different combination of currents in the PF coils. In the presence of disturbances it tries to avoid the current saturations by relaxing the constraints on the plasma shape control. The CLA system has been successfully implemented on the JET tokamak and fully commissioned in 2011. This paper presents the first experimental results achieved in 2011–2012 during the restart and the ITER-like wall campaigns at JET.

Demonstrating the capability and reliability of NDT inspections

International Nuclear Information System (INIS)

Wooldridge, A.B.

1996-01-01

This paper discusses some recent developments in demonstrating the capability of ultrasonics, eddy currents and radiography both theoretically and in practice, and indicates where further evidence is desirable. Magnox Electric has been involved with development of theoretical models for all three of these inspection methods. Feedback from experience on plant is also important to avoid overlooking any practical limitations of the inspections, and to ensure that the metallurgical characteristics of potential defects have been properly taken into account when designing and qualifying the inspections. For critical applications, inspection techniques are often supported by a Technical Justification which draws on all the relevant theoretical and experimental evidence, as well as experience of inspections on plant. The role of technical justifications is discussed in the context of inspection qualification. (author)

Do social networks and technological capabilities help knowledge management?

Directory of Open Access Journals (Sweden)

Encarnación García-Sánchez

2017-12-01

Full Text Available Dynamic capabilities are currently becoming an important extension of the theory of resources and capabilities that enables companies to adapt better in the current competitive environment. This paper examines how knowledge management, a dynamic function related to management or administration of a set of knowledge flows, develops thanks to the greater dynamism of social networks. It then shows how this relationship is especially strengthened by different technological capabilities. To achieve these goals, the paper examines the main tools that permit companies to develop an ability to achieve competitive advantage relative to the technological capabilities of managers and workers, social networks and knowledge management.

Development of Capabilities for New Experimental Studies on the Elasticity and Rheology of Lower Mantle Minerals

Science.gov (United States)

Triplett, R.; Weidner, D.; Whitaker, M. L.; Chen, H.; Li, L.

2017-12-01

Key mineralogical components of the mid-mantle of the Earth have historically been difficult to obtain elasticity data on because they either cannot be recovered to ambient conditions (e.g. calcium silicate perovskite) or back-transform during experimental preparation (e.g. magnesium silicate perovskite). Recently the conditions of the mid-mantle (14+ GPa, 1500+ K) and even of the lower mantle (24+ GPa, 1800+ K) have become reachable using multi-anvil apparatuses (MAA) with in-situ synchrotron x-ray capabilities, but the capabilities of these facilities have not yet fully matured. Examples include that reaching such pressures typically results in samples that are too small for ultrasonics, the few ultrasonics experiments done at these conditions have extremely limited x-ray visibility, and rheological experiments that apply differential stress have not been done at these conditions on large volume samples. The pressure reachable in a Large Volume Press (LVP) is limited by the properties of available ultra-hard (UH) materials such as tungsten carbide (WC) and x-ray transparent polycrystalline diamond (PCD) and cubic boron nitride (cBN). A key factor is the interaction of 1st stage anvils and anvils of UH materials; obtaining WC anvils of larger size is prohibitive in both capability and cost, and anvils of hardened steel are limited in the tonnage that can be applied before damage occurs. Other complications include the difference in compressibility between WC and PCD/cBN anvils and the availability of WC with simultaneous high compressive strength (pressure gain per tonnage) and high transverse rupture strength (lower chance of blowout and reusability). The DT25 press to be used at the new NSLS-II beamline XPD-D is a Kawaii-style LVP MAA which accepts 25 mm UH 2nd-stage anvils and has the capability to apply a differential load while at extreme conditions. We report on our development of techniques to do new and expanded experiments at lower mantle conditions

Promoting practical clinical management learning: the current situation about Information and Communications Technology capability development in student nurses.

Science.gov (United States)

Willmer, Marian

2005-11-01

This paper is about work-based learning in information management for student nurses. It seeks, through a literature review, to make a case for and promote Information and Communications Technology capability development in student nurses within their clinical environment. The profession of nursing, like many other jobs, is facing the increasing usage of information technology in day-to-day operations. Admission and discharges of patients have been held on computer databases since at least the 1980s. With the new Labour Government in 1997, increasing focus was placed on the effectiveness of the National Health Service and using computers as one way to assist in achieving greater effectiveness. Nurse education therefore needed to reflect this need and support trainee nurses to acquire skills in Information and Communications Technology. This paper is part of an ongoing professional doctorate inquiry into Information and Communications Technology capability development in student nurses. A literature search was conducted on teaching information and technology skills via Cumulative Index to Nursing and Allied Health Literature. Most of the available studies were neither based on the UK nor were they about student nurses. As there is a dearth of published work in this specific area, relevant, related and tangential literature was reviewed. It is argued that current practice and published work on Information and Communications Technology capability development by student nurses hardly exists. The literature confirmed that success in this area requires sound change management, an understanding of National Health Service culture, and effective people leadership skills. Nurse educators and managers need to pay more attention to understand how organizations work, particularly organizations where student nurses carry out their work. As the search revealed a significant gap in the literature in this area, a practical conceptual framework to fully analyse, develop and

A Process for Assessing NASA's Capability in Aircraft Noise Prediction Technology

Science.gov (United States)

Dahl, Milo D.

2008-01-01

An acoustic assessment is being conducted by NASA that has been designed to assess the current state of the art in NASA s capability to predict aircraft related noise and to establish baselines for gauging future progress in the field. The process for determining NASA s current capabilities includes quantifying the differences between noise predictions and measurements of noise from experimental tests. The computed noise predictions are being obtained from semi-empirical, analytical, statistical, and numerical codes. In addition, errors and uncertainties are being identified and quantified both in the predictions and in the measured data to further enhance the credibility of the assessment. The content of this paper contains preliminary results, since the assessment project has not been fully completed, based on the contributions of many researchers and shows a select sample of the types of results obtained regarding the prediction of aircraft noise at both the system and component levels. The system level results are for engines and aircraft. The component level results are for fan broadband noise, for jet noise from a variety of nozzles, and for airframe noise from flaps and landing gear parts. There are also sample results for sound attenuation in lined ducts with flow and the behavior of acoustic lining in ducts.

Integrated Program of Experimental Diagnostics at the NNSS: An Integrated, Prioritized Work Plan for Diagnostic Development and Maintenance and Supporting Capability

International Nuclear Information System (INIS)

2010-01-01

This Integrated Program of Experimental Diagnostics at the NNSS is an integrated prioritized work plan for the Nevada National Security Site (NNSS), formerly the Nevada Test Site (NTS), program that is independent of individual National Security Enterprise Laboratories (Labs) requests or specific Subprograms being supported. This prioritized work plan is influenced by national priorities presented in the Predictive Capability Framework (PCF) and other strategy documents (Primary and Secondary Assessment Technologies Plans and the Plutonium Experiments Plan). This document satisfies completion criteria for FY 2010 MRT milestone No.3496: Document an integrated, prioritized work plan for diagnostic development, maintenance, and supporting capability. This document is an update of the 3-year NNSS plan written a year ago, September 21, 2009, to define and understand Lab requests for diagnostic implementation. This plan is consistent with Lab interpretations of the PCF, Primary Assessment Technologies, and Plutonium Experiment plans.

Comparison of experimental and theoretical reaction rail currents, rail voltages, and airgap fields for the linear induction motor research vehicle

Science.gov (United States)

Elliott, D. G.

1977-01-01

Measurements of reaction rail currents, reaction rail voltages, and airgap magnetic fields in tests of the Linear Induction Motor Research Vehicle (LIMRV) were compared with theoretical calculations from the mesh/matrix theory. It was found that the rail currents and magnetic fields predicted by the theory are within 20 percent of the measured currents and fields at most motor locations in most of the runs, but differ by as much as a factor of two in some cases. The most consistent difference is a higher experimental than theoretical magnetic field near the entrance of the motor and a lower experimental than theoretical magnetic field near the exit. The observed differences between the theoretical and experimental magnetic fields and currents do not account for the differences of as much as 26 percent between the theoretical and experimental thrusts.

Precision intercomparison of beam current monitors at CEBAF

International Nuclear Information System (INIS)

Kazimi, R.; Dunham, B.; Krafft, G.A.; Legg, R.; Liang, C.; Sinclair, C.; Mamosser, J.

1995-01-01

The CEBAF accelerator delivers a CW electron beam at fundamental 1497 MHz, with average beam current up to 200 μA. Accurate, stable nonintercepting beam current monitors are required for: setup/control, monitoring of beam current and beam losses for machine protection and personnel safety, and providing beam current information to experimental users. Fundamental frequency stainless steel RF cavities have been chosen for these beam current monitors. This paper reports on precision intercomparison between two such RF cavities, an Unser monitor, and two Faraday cups, all located in the injector area. At the low beam energy in the injector, it is straightforward to verify the high efficiency of the Faraday cups, and the Unser monitor included a wire through it to permit an absolute calibration. The cavity intensity monitors have proven capable of stable, high precision monitoring of the beam current

Reduction of the heat leak in superconducting system at half-wave-rectified current mode by peltier current lead

International Nuclear Information System (INIS)

Yamaguchi, Takayuki; Ohtaki, Naohiro; Nakamura, Keiji; Yamaguchi, Satarou; Hasegawa, Yasuhiro

2002-01-01

Experiments of Peltier current lead (PCL) were performed by the way of half-wave-rectified current (HWRC) for an evaluation of the PCL system in the drive with the large-rippled current. The current ripple of the HWRC is large, and we discussed the cooling capability of the current ripple. The experimental results revealed that the temperature difference of the thermoelectric-element (TE) increased with the magnitude of the current in the PCL system, despite the large current ripple. Calorimetric measurements revealed that the PCL reduced the heat leak of 60% for the peak current 90A. We compared the PCL systems of the direct current (dc) mode and the HWRC mode. The results showed that the current dependence of the temperature difference in the HWRC mode did not match that of the dc mode, but those of the heat leak matched well. The performance of the Peltier cooling in the HWRC mode is reduced to be 2/π time of the Seebeck coefficient for the dc mode by using the time-average method. (author)

Reduction of the heat leak in superconducting system at half-wave-rectified current mode by peltier current lead

CERN Document Server

Yamaguchi, T; Nakamura, K; Yamaguchi, S; Hasegawa, Y

2002-01-01

Experiments of Peltier current lead (PCL) were performed by the way of half-wave-rectified current (HWRC) for an evaluation of the PCL system in the drive with the large-rippled current. The current ripple of the HWRC is large, and we discussed the cooling capability of the current ripple. The experimental results revealed that the temperature difference of the thermoelectric-element (TE) increased with the magnitude of the current in the PCL system, despite the large current ripple. Calorimetric measurements revealed that the PCL reduced the heat leak of 60% for the peak current 90A. We compared the PCL systems of the direct current (dc) mode and the HWRC mode. The results showed that the current dependence of the temperature difference in the HWRC mode did not match that of the dc mode, but those of the heat leak matched well. The performance of the Peltier cooling in the HWRC mode is reduced to be 2/pi time of the Seebeck coefficient for the dc mode by using the time-average method. (author)

Liquid metal current collectors for high-speed rotating machinery

International Nuclear Information System (INIS)

Carr, S.L.

1976-01-01

Recent interest in superconducting motors and generators has created a renewed interest in homopolar machinery. Homopolar machine designs have always been limited by the need for compact, high-current, low-voltage, sliding electrical curent collectors. Conventional graphite-based solid brushes are inadequate for use in homopolar machines. Liquid metals, under certain conditions of relative sliding velocities, electrical currents, and magnetic fields are known to be capable of performing well in homopolar machines. An effort to explore the capabilities and limits of a tongue-and-groove style current collector, utilizing sodium-potassium eutectic alloy (NaK) as the working fluid in high sliding speed operation is reported here. A double current collector generator model with a 14.5-cm maximum rotor diameter, 20,000 rpm rotational capability, and electrical current carrying ability was constructed and operated successfully at a peripheral velocity of 125 m/s. The limiting factor in these experiments was a high-speed fluid-flow instability resulting in the ejection of the working fluid from the operating portions of the collectors. The effects of collector size and geometry, working fluid (NaK or water), and cover gas pressure are reported. Hydrodynamic frictional torque-speed curves are given for the two fluids and for several geometries. Electrical resistances as a function of peripheral velocity at 60 amperes are reported, and the phenomenology of the high-speed fluid-flow instabilities is discussed. The possibility of long-term high-speed operation of current collectors of the tongue-and-groove type, along with experimental and theoretical hydrodynamic friction losses at high peripheral velocities, is considered

Facility Interface Capability Assessment (FICA) project report

International Nuclear Information System (INIS)

Pope, R.B.; MacDonald, R.R.; Viebrock, J.M.; Mote, N.

1995-09-01

The US Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is responsible for developing the Civilian Radioactive Waste Management System (CRWMS) to accept spent nuclear fuel from commercial facilities. The objective of the Facility Interface Capability Assessment (FICA) project was to assess the capability of each commercial spent nuclear fuel (SNF) storage facility, at which SNF is stored, to handle various SNF shipping casks. The purpose of this report is to present and analyze the results of the facility assessments completed within the FICA project. During Phase 1, the data items required to complete the facility assessments were identified and the database for the project was created. During Phase 2, visits were made to 122 facilities on 76 sites to collect data and information, the database was updated, and assessments of the cask-handling capabilities at each facility were performed. Each assessment of cask-handling capability contains three parts: the current capability of the facility (planning base); the potential enhanced capability if revisions were made to the facility licensing and/or administrative controls; and the potential enhanced capability if limited physical modifications were made to the facility. The main conclusion derived from the planning base assessments is that the current facility capabilities will not allow handling of any of the FICA Casks at 49 of the 122 facilities evaluated. However, consideration of potential revisions and/or modifications showed that all but one of the 49 facilities could be adapted to handle at least one of the FICA Casks. For this to be possible, facility licensing, administrative controls, and/or physical aspects of the facility would need to be modified

Facility Interface Capability Assessment (FICA) project report

Energy Technology Data Exchange (ETDEWEB)

Pope, R.B. [ed.] [Oak Ridge National Lab., TN (United States); MacDonald, R.R. [ed.] [Civilian Radioactive Waste Management System, Vienna, VA (United States); Viebrock, J.M.; Mote, N. [Nuclear Assurance Corp., Norcross, GA (United States)

1995-09-01

The US Department of Energy`s (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is responsible for developing the Civilian Radioactive Waste Management System (CRWMS) to accept spent nuclear fuel from commercial facilities. The objective of the Facility Interface Capability Assessment (FICA) project was to assess the capability of each commercial spent nuclear fuel (SNF) storage facility, at which SNF is stored, to handle various SNF shipping casks. The purpose of this report is to present and analyze the results of the facility assessments completed within the FICA project. During Phase 1, the data items required to complete the facility assessments were identified and the database for the project was created. During Phase 2, visits were made to 122 facilities on 76 sites to collect data and information, the database was updated, and assessments of the cask-handling capabilities at each facility were performed. Each assessment of cask-handling capability contains three parts: the current capability of the facility (planning base); the potential enhanced capability if revisions were made to the facility licensing and/or administrative controls; and the potential enhanced capability if limited physical modifications were made to the facility. The main conclusion derived from the planning base assessments is that the current facility capabilities will not allow handling of any of the FICA Casks at 49 of the 122 facilities evaluated. However, consideration of potential revisions and/or modifications showed that all but one of the 49 facilities could be adapted to handle at least one of the FICA Casks. For this to be possible, facility licensing, administrative controls, and/or physical aspects of the facility would need to be modified.

Current Parental Depression and Offspring Perceived Self-Competence: A Quasi-Experimental Examination

OpenAIRE

Class, Quetzal A.; D’Onofrio, Brian M.; Singh, Amber L.; Ganiban, Jody M.; Spotts, E. L.; Lichtenstein, Paul; Reiss, David; Neiderhiser, Jenae M.

2012-01-01

A genetically-informed, quasi-experimental design was used to examine the genetic and environmental processes underlying associations between current parental depressive symptoms and offspring perceived self-competence. Participants, drawn from a population-based Swedish sample, were 852 twin pairs and their male (52%) and female offspring aged 15.7 ± 2.4 years. Parental depressive symptoms were measured using the Center for Epidemiological Studies Depression scale. Offspring perceived self-c...

Arctic Observing Network Data Management: Current Capabilities and Their Promise for the Future

Science.gov (United States)

Collins, J.; Fetterer, F.; Moore, J. A.

2008-12-01

CADIS (the Cooperative Arctic Data and Information Service) serves as the data management, discovery and delivery component of the Arctic Observing Network (AON). As an International Polar Year (IPY) initiative, AON comprises 34 land, atmosphere and ocean observation sites, and will acquire much of the data coming from the interagency Study of Environmental Arctic Change (SEARCH). CADIS is tasked with ensuring that these observational data are managed for long term use by members of the entire Earth System Science community. Portions of CADIS are either in use by the community or available for testing. We now have an opportunity to evaluate the feedback received from our users, to identify any design shortcomings, and to identify those elements which serve their purpose well and will support future development. This presentation will focus on the nuts-and-bolts of the CADIS development to date, with an eye towards presenting lessons learned and best practices based on our experiences so far. The topics include: - How did we assess our users' needs, and how are those contributions reflected in the end product and its capabilities? - Why did we develop a CADIS metadata profile, and how does it allow CADIS to support preservation and scientific interoperability? - How can we shield the user from metadata complexities (especially those associated with various standards) while still obtaining the metadata needed to support an effective data management system? - How can we bridge the gap between the data storage formats considered convenient by researchers in the field, and those which are necessary to provide data interoperability? - What challenges have been encountered in our efforts to provide access to federated data (data stored outside of the CADIS system)? - What are the data browsing and visualization needs of the AON community, and which tools and technologies are most promising in terms of supporting those needs? A live demonstration of the current

A Grid Connected Transformerless Inverter and its Model Predictive Control Strategy with Leakage Current Elimination Capability

Directory of Open Access Journals (Sweden)

J. Fallah Ardashir

2017-06-01

Full Text Available This paper proposes a new single phase transformerless Photovoltaic (PV inverter for grid connected systems. It consists of six power switches, two diodes, one capacitor and filter at the output stage. The neutral of the grid is directly connected to the negative terminal of the source. This results in constant common mode voltage and zero leakage current. Model Predictive Controller (MPC technique is used to modulate the converter to reduce the output current ripple and filter requirements. The main advantages of this inverter are compact size, low cost, flexible grounding configuration. Due to brevity, the operating principle and analysis of the proposed circuit are presented in brief. Simulation and experimental results of 200W prototype are shown at the end to validate the proposed topology and concept. The results obtained clearly verifies the performance of the proposed inverter and its practical application for grid connected PV systems.

Experimental Investigation of a Direct Methanol Fuel Cell with Hilbert Fractal Current Collectors

Directory of Open Access Journals (Sweden)

Jing-Yi Chang

2014-01-01

Full Text Available The Hilbert curve is a continuous type of fractal space-filling curve. This fractal curve visits every point in a square grid with a size of 2×2, 4×4, or any other power of two. This paper presents Hilbert fractal curve application to direct methanol fuel cell (DMFC current collectors. The current collectors are carved following first, second, and third order Hilbert fractal curves. These curves give the current collectors different free open ratios and opening perimeters. We conducted an experimental investigation into DMFC performance as a function of the free open ratio and opening perimeter on the bipolar plates. Nyquist plots of the bipolar plates are made and compared using electrochemical impedance spectroscopy (EIS experiments to understand the phenomena in depth. The results obtained in this paper could be a good reference for future current collector design.

Eddy current technologies for thick metal structures

International Nuclear Information System (INIS)

Takagi, Toshiyuki; Endo, Hisashi

2004-01-01

One of approach of an eddy current testing (ECT) for thick metal structures is introduced. The detection limit of ECT is capable of enlarging thick more than 10 mm, which is ordinarily about 5 mm, by the design of probe. On the basis of results of numerical analysis, the defect detection in thick and shape is evaluated by the distribution of experimental ECT signals. The problems of ECT for thick metal structures and measures, approach to probe design, the specifications of probe, evaluation of experimental results and defect detection are described. By ECT fast simulator, good slit sharp is simulated in the case of 10 and 20 mm of EDM slit length and 5, 10 and 15 mm of slit height. (S.Y.)

Organizational Learning Capability: An Example of University Hospital

Directory of Open Access Journals (Sweden)

Yasin UZUNTARLA

2015-06-01

Full Text Available In health care institutions aiming healthy society by the way protecting and promoting human health, reaching information has a vital importance. This descriptive research purposed an evaluation of organizational learning capability of 396 employees working in Gülhane Military Medical Academy Hospital. A questionnaire including socio-demographic characteristics was used along with Organizational Learning Capability scale designed by Ricardo CHIVA and His Friends. Data acquired was analyzed with SPSS 15.0 program. Participants’ Organizational Learning Capability and its subscales means were assessed in terms of their sociodemographic characteristics. Assessing participants’ answers in terms of 5 subscales which are experimentation, risk taking, interaction with the external environment, dialogue and participatory decision-making; for education level and professional groups, statistical significant differences was found between Organizational Learning Capability and its subscales means.

High resolution, monochromatic x-ray topography capability at CHESS

Energy Technology Data Exchange (ETDEWEB)

Finkelstein, K. D., E-mail: kdf1@cornell.edu; Pauling, A.; Brown, Z. [CHESS, Cornell University, Ithaca, NY (United States); Jones, R. [Department of Physics, University of Connecticut, Storrs, CT (United States); Tarun, A.; Misra, D. S. [IIa Technologies (Singapore); Jupitz, S. [St. Mary’s College of Maryland, St. Mary’s City, MD (United States); Sagan, D. C. [CLASSE, Cornell University, Ithaca, NY (United States)

2016-07-27

CHESS has a monochromatic x-ray topography capability serving continually expanding user interest. The setup consists of a beam expanding monochromator, 6-circle diffactometer, and CHESS designed CMOS camera with real time sample-alignment capability. This provides rocking curve mapping with angle resolution as small as 2 µradians, spatial resolution to 3 microns, and field of view up to 7mm. Thus far the capability has been applied for: improving CVD-diamond growth, evaluating perfection of ultra-thin diamond membranes, correlating performance of diamond-based electronics with crystal defect structure, and defect analysis of single crystal silicon carbide. This paper describes our topography system, explains its capabilities, and presents experimental results from several applications.

High resolution, monochromatic x-ray topography capability at CHESS

International Nuclear Information System (INIS)

Finkelstein, K. D.; Pauling, A.; Brown, Z.; Jones, R.; Tarun, A.; Misra, D. S.; Jupitz, S.; Sagan, D. C.

2016-01-01

CHESS has a monochromatic x-ray topography capability serving continually expanding user interest. The setup consists of a beam expanding monochromator, 6-circle diffactometer, and CHESS designed CMOS camera with real time sample-alignment capability. This provides rocking curve mapping with angle resolution as small as 2 µradians, spatial resolution to 3 microns, and field of view up to 7mm. Thus far the capability has been applied for: improving CVD-diamond growth, evaluating perfection of ultra-thin diamond membranes, correlating performance of diamond-based electronics with crystal defect structure, and defect analysis of single crystal silicon carbide. This paper describes our topography system, explains its capabilities, and presents experimental results from several applications.

Exploration Medical Capability (ExMC) Projects

Science.gov (United States)

Wu, Jimmy; Watkins, Sharmila; Baumann, David

2010-01-01

During missions to the Moon or Mars, the crew will need medical capabilities to diagnose and treat disease as well as for maintaining their health. The Exploration Medical Capability Element develops medical technologies, medical informatics, and clinical capabilities for different levels of care during space missions. The work done by team members in this Element is leading edge technology, procedure, and pharmacological development. They develop data systems that protect patient's private medical information, aid in the diagnosis of medical conditions, and act as a repository of relevant NASA life sciences experimental studies. To minimize the medical risks to crew health the physicians and scientists in this Element develop models to quantify the probability of medical events occurring during a mission. They define procedures to treat an ill or injured crew member who does not have access to an emergency room and who must be cared for in a microgravity environment where both liquids and solids behave differently than on Earth. To support the development of these medical capabilities, the Element manages the development of medical technologies that prevent, monitor, diagnose, and treat an ill or injured crewmember. The Exploration Medical Capability Element collaborates with the National Space Biomedical Research Institute (NSBRI), the Department of Defense, other Government-funded agencies, academic institutions, and industry.

Conceptualizing innovation capabilities: A contingency perspective

Directory of Open Access Journals (Sweden)

Tor Helge Aas

2017-01-01

Full Text Available Empirical research has confirmed that a positive relationship exists between the implementation of innovation activities and the future performance of organizations. Firms utilize resources and capabilities to develop innovations in the form of new products, services or processes. Some firms prove to be better at reproducing innovation success than others, and the capacity to do so is referred to as innovation capability. However, the term innovation capability is ambiguously treated in extant literature. There are several different definitions of the concept and the distinction between innovation capabilities and other types of capabilities, such as dynamic capabilities, is neither explicitly stated, nor is the relationship between the concept and other resource- and capability-based concepts within strategy theory established. Although innovation is increasingly identified as crucial for a firm’s sustainable competitiveness in contemporary volatile and complex markets, the strategy-innovation link is underdeveloped in extant research. To overcome this challenge this paper raises the following research question: What type of innovation capabilities are required to innovate successfully? Due to the status of the extant research, we chose a conceptual research design to answer our research question and the paper contributes with a conceptual framework to discuss what innovation capabilities firms need to reproduce innovation success. Based on careful examination of current literature on innovation capability specifically, and the strategy-innovation link in general, we suggest that innovation capability must be viewed along two dimensions – innovation novelty and market characteristics. This framework enables the identification of four different contexts for innovation capabilities in a two-bytwo matrix. We discuss the types of innovation capabilities necessary within the four different contexts. This novel framework contributes to the

Faculty perceptions of the strengths, weaknesses and future prospects of the current medical undergraduate experimental physiology curriculum in Gujarat, India.

Science.gov (United States)

Paralikar, Swapnil; Shah, Chinmay

2015-01-01

Over the past several years, an opinion has emerged in India that the current practical curricula in medical schools fail to meet many of the objectives for which they were instituted. Hence, this study has assessed the perception of physiology faculty members regarding the current experimental physiology curriculum in one Indian state, Gujarat. The faculty were of the opinion that many of the topics currently taught in experimental physiology (amphibian nerve-muscle and heart muscle experiments) were outdated and clinically irrelevant: Therefore, the faculty advocated that duration of teaching time devoted to some of these topics should be reduced and topics with clinical relevance should be introduced at the undergraduate level. The faculty also felt that more emphasis should be laid on highlighting the clinical aspect related to each concept taught in experimental physiology . Moreover, a majority of faculty members were in favour of replacing the current practice in Gujarat of teaching experimental physiology only by explanation of graphs obtained from experiments conducted in the previous years, with computer assisted learning in small groups.

Maternal hypothyroidism: An overview of current experimental models.

Science.gov (United States)

Ghanbari, Mahboubeh; Ghasemi, Asghar

2017-10-15

Maternal hypothyroidism (MH) is the most common cause of transient congenital hypothyroidism. Different animal models are used for assessing developmental effects of MH in offspring. The severity and status of hypothyroidism in animal models must be a reflection of the actual conditions in humans. To obtain comparable results with different clinical conditions, which lead to MH in humans, several factors have been suggested for researchers to consider before designing the experimental models. Regarding development of fetal body systems during pregnancy, interference at different times provides different results and the appropriate time for induction of hypothyroidism should be selected based on accurate time of development of the system under assessment. Other factors that should be taken into consideration include, physiological and biochemical differences between humans and other species, thyroid hormone-independent effects of anti-thyroid drugs, circadian rhythms in TSH secretion, sex differences, physical and psychological stress. This review addresses essential guidelines for selecting and managing the optimal animal model for MH as well as discussing the pros and cons of currently used models. Copyright © 2017 Elsevier Inc. All rights reserved.

Modelling the transient behaviour of pulsed current tungsten-inert-gas weldpools

Science.gov (United States)

Wu, C. S.; Zheng, W.; Wu, L.

1999-01-01

A three-dimensional model is established to simulate the pulsed current tungsten-inert-gas (TIG) welding process. The goal is to analyse the cyclic variation of fluid flow and heat transfer in weldpools under periodic arc heat input. To this end, an algorithm, which is capable of handling the transience, nonlinearity, multiphase and strong coupling encountered in this work, is developed. The numerical simulations demonstrate the transient behaviour of weldpools under pulsed current. Experimental data are compared with numerical results to show the effectiveness of the developed model.

Developing Acquisition IS Integration Capabilities

DEFF Research Database (Denmark)

Wynne, Peter J.

2016-01-01

An under researched, yet critical challenge of Mergers and Acquisitions (M&A), is what to do with the two organisations’ information systems (IS) post-acquisition. Commonly referred to as acquisition IS integration, existing theory suggests that to integrate the information systems successfully......, an acquiring company must leverage two high level capabilities: diagnosis and integration execution. Through a case study, this paper identifies how a novice acquirer develops these capabilities in anticipation of an acquisition by examining its use of learning processes. The study finds the novice acquirer...... applies trial and error, experimental, and vicarious learning processes, while actively avoiding improvisational learning. The results of the study contribute to the acquisition IS integration literature specifically by exploring it from a new perspective: the learning processes used by novice acquirers...

Spike train generation and current-to-frequency conversion in silicon diodes

Science.gov (United States)

Coon, D. D.; Perera, A. G. U.

1989-01-01

A device physics model is developed to analyze spontaneous neuron-like spike train generation in current driven silicon p(+)-n-n(+) devices in cryogenic environments. The model is shown to explain the very high dynamic range (0 to the 7th) current-to-frequency conversion and experimental features of the spike train frequency as a function of input current. The devices are interesting components for implementation of parallel asynchronous processing adjacent to cryogenically cooled focal planes because of their extremely low current and power requirements, their electronic simplicity, and their pulse coding capability, and could be used to form the hardware basis for neural networks which employ biologically plausible means of information coding.

National power grid simulation capability : need and issues

Energy Technology Data Exchange (ETDEWEB)

Petri, Mark C. [Argonne National Lab. (ANL), Argonne, IL (United States)

2009-06-02

On December 9 and 10, 2008, the Department of Homeland Security (DHS) Science and Technology Directorate sponsored a national workshop at Argonne National Laboratory to explore the need for a comprehensive modeling and simulation capability for the national electric power grid system. The workshop brought together leading electric power grid experts from federal agencies, the national laboratories, and academia to discuss the current state of power grid science and engineering and to assess if important challenges are being met. The workshop helped delineate gaps between grid needs and current capabilities and identify issues that must be addressed if a solution is to be implemented. This report is a result of the workshop and highlights power grid modeling and simulation needs, the barriers that must be overcome to address them, and the benefits of a national power grid simulation capability.

Graphical Visualization of Human Exploration Capabilities

Science.gov (United States)

Rodgers, Erica M.; Williams-Byrd, Julie; Arney, Dale C.; Simon, Matthew A.; Williams, Phillip A.; Barsoum, Christopher; Cowan, Tyler; Larman, Kevin T.; Hay, Jason; Burg, Alex

2016-01-01

of planned future work to modify the computer program to include additional data and of alternate capability roadmap formats currently under consideration.

Technological capability at the Brazilian official pharmaceutical laboratories

Directory of Open Access Journals (Sweden)

José Vitor Bomtempo Martins

2008-10-01

Full Text Available This paper studies the technological capability in the Brazilian Official Pharmaceutical Laboratories [OPL]. The technological capability analysis could contribute to organization strategies and governmental actions in order to improve OPL basic tasks as well to incorporate new ones, particularly concerning the innovation management. Inspired in Figueiredo (2000, 2003a, 2003b and Figueiredo and Ariffin (2003, a framework was drawn and adapted to pharmaceutical industry characteristics and current sanitary and health legislation. The framework allows to map different dimensions of the technological capability (installations, processes, products, equipments, organizational capability and knowledge management and the level attained by OPL (ordinary or innovating capability. OPL show a good development of ordinary capabilities, particularly in Product and Processes. Concerning the other dimensions, OPL are quite diverse. In general, innovating capabilities are not much developed. In the short term, it was identified a dispersion in the capacitating efforts. Considering their present level and the absorption efforts, good perspectives can be found in Installations, Processes and Organizational Capability. A lower level of efforts in Products and Knowledge Management could undermine these capabilities in the future.

Scientific capabilities of the advanced light source for radioactive materials

International Nuclear Information System (INIS)

Shuh, D.K.

2007-01-01

The Advanced Light Source (ALS) of Lawrence Berkeley National Laboratory (LBNL) is a third-generation synchrotron radiation light source and is a U.S. Department of Energy (DOE) national user facility. Currently, the ALS has approximately forty-five operational beamlines spanning a spectrum of scientific disciplines, and provides scientific opportunities for more than 2 000 users a year. Access to the resources of the ALS is through a competitive proposal mechanism within the general user program. Several ALS beamlines are currently being employed for a range of radioactive materials investigations. These experiments are reviewed individually relying on a graded hazard approach implemented by the ALS in conjunction with the LBNL Environmental, Health, and Safety (EH and S) Radiation Protection Program. The ALS provides radiological work authorization and radiological control technician support and assistance for accepted user experimental programs. LBNL has several radioactive laboratory facilities located near the ALS that provide support for ALS users performing experiments with radioactive materials. The capabilities of the ALS beamlines for investigating radioactive materials are given and examples of several past studies are summarised. (author)

Current Challenges in the First Principle Quantitative Modelling of the Lower Hybrid Current Drive in Tokamaks

Science.gov (United States)

Peysson, Y.; Bonoli, P. T.; Chen, J.; Garofalo, A.; Hillairet, J.; Li, M.; Qian, J.; Shiraiwa, S.; Decker, J.; Ding, B. J.; Ekedahl, A.; Goniche, M.; Zhai, X.

2017-10-01

The Lower Hybrid (LH) wave is widely used in existing tokamaks for tailoring current density profile or extending pulse duration to steady-state regimes. Its high efficiency makes it particularly attractive for a fusion reactor, leading to consider it for this purpose in ITER tokamak. Nevertheless, if basics of the LH wave in tokamak plasma are well known, quantitative modeling of experimental observations based on first principles remains a highly challenging exercise, despite considerable numerical efforts achieved so far. In this context, a rigorous methodology must be carried out in the simulations to identify the minimum number of physical mechanisms that must be considered to reproduce experimental shot to shot observations and also scalings (density, power spectrum). Based on recent simulations carried out for EAST, Alcator C-Mod and Tore Supra tokamaks, the state of the art in LH modeling is reviewed. The capability of fast electron bremsstrahlung, internal inductance li and LH driven current at zero loop voltage to constrain all together LH simulations is discussed, as well as the needs of further improvements (diagnostics, codes, LH model), for robust interpretative and predictive simulations.

Experimental study on the evolution of Peregrine breather with uniform-depth adverse currents

Science.gov (United States)

Liao, B.; Ma, Y.; Ma, X.; Dong, G.

2018-05-01

A series of laboratory experiments were performed to study the evolution of Peregrine breather (PB) in a wave flume in finite depth, and wave trains were initially generated in a region of quiescent water and then propagated into an adverse current region for which the current velocity strength gradually increased from zero to an approximately stable value. The PB is often considered as a prototype of oceanic freak waves that can focus wave energy into a single wave packet. In the experiment, the cases were selected with the relative water depths k0h (k0 is the wave number in quiescent water and h is the water depth) varying from 3.11 through 8.17, and the initial wave steepness k0a0 (a0 is the background wave amplitude) ranges between 0.065 and 0.120. The experimental results show the persistence of the breather evolution dynamics even in the presence of strong opposing currents. We have shown that the characteristic spectrum of the PB persists even on strong currents, thus making it a viable characteristic for prediction of freak waves. It was also found that the adverse currents tend to shift the focusing point upstream compared to the cases without currents. Furthermore, it was found that uniform-depth adverse currents can reduce the breather extension in time domain.

Experimental investigation of droplet separation in a horizontal counter-current air/water stratified flow

International Nuclear Information System (INIS)

Gabriel, Stephan Gerhard

2015-01-01

A stratified counter-current two-phase gas/liquid flow can occur in various technical systems. In the past investigations have mainly been motivated by the possible occurrence of these flows in accident scenarios of nuclear light water-reactors and in numerous applications in process engineering. However, the precise forecast of flow parameters, is still challenging, for instance due to their strong dependency on the geometric boundary conditions. A new approach which uses CFD methods (Computational Fluid Dynamics) promises a better understanding of the flow phenomena and simultaneously a higher scalability of the findings. RANS methods (Reynolds Averaged Navier Stokes) are preferred in order to compute industrial processes and geometries. A very deep understanding of the flow behavior and equation systems based on real physics are necessary preconditions to develop the equation system for a reliable RANS approach with predictive power. Therefore, local highly resolved, experimental data is needed in order to provide and validate the required turbulence and phase interaction models. The central objective of this work is to provide the data needed for the code development for these unsteady, turbulent and three-dimensional flows. Experiments were carried out at the WENKA facility (Water Entrainment Channel Karlsruhe) at the Karlsruhe Institute of Technology (KIT). The work consists of a detailed description of the test-facility including a new bended channel, the measurement techniques and the experimental results. The characterization of the new channel was done by flow maps. A high-speed imaging study gives an impression of the occurring flow regimes, and different flow phenomena like droplet separation. The velocity distributions as well as various turbulence values were investigated by particle image velocimetry (PIV). In the liquid phase fluorescent tracer-particles were used to suppress optical reflections from the phase surface (fluorescent PIV, FPIV

Experimental Physical Sciences Vistas: MaRIE (draft)

Energy Technology Data Exchange (ETDEWEB)

Shlachter, Jack [Los Alamos National Laboratory

2010-09-08

security science challenges. Our first issue of Vistas focused on our current national user facilities (the Los Alamos Neutron Science Center [LANSCE], the National High Magnetic Field Laboratory-Pulsed Field Facility, and the Center for Integrated Nanotechnologies) and the vitality they bring to our Laboratory. These facilities are a magnet for students, postdoctoral researchers, and staff members from all over the world. This, in turn, allows us to continue to develop and maintain our strong staff across the relevant disciplines and conduct world-class discovery science. The second issue of Vistas was devoted entirely to the Laboratory's materials strategy - one of the three strategic science thrusts for the Laboratory. This strategy has helped focus our thinking for MaRIE. We believe there is a bright future in cutting-edge experimental materials research, and that a 21st-century facility with unique capability is necessary to fulfill this goal. The Laboratory has spent the last several years defining MaRIE, and this issue of Vistas presents our current vision of that facility. MaRIE will leverage LANSCE and our other user facilities, as well as our internal and external materials community for decades to come, giving Los Alamos a unique competitive advantage, advancing materials science for the Laboratory's missions and attracting and recruiting scientists of international stature. MaRIE will give the international materials research community a suite of tools capable of meeting a broad range of outstanding grand challenges.

Experimental study on short-circuit characteristics of the new protection circuit of insulated gate bipolar transistor

International Nuclear Information System (INIS)

Ji, In-Hwan; Choi, Young-Hwan; Ha, Min-Woo; Han, Min-Koo; Choi, Yearn-Ik

2006-01-01

A new protection circuit employing the collector to emitter voltage (V CE ) sensing scheme for short-circuit withstanding capability of the insulated gate bipolar transistor (IGBT) is proposed and verified by experimental results. Because the current path between the gate and collector can be successfully eliminated in the proposed protection circuit, the power consumption can be reduced and the gate input impedance can be increased. Previous study is limited to dc characteristics. However, experimental results show that the proposed protection circuit successfully reduces the over-current of main IGBT by 80.4% under the short-circuit condition

Advanced Simulation Capability for Turbopump Cavitation Dynamics Guided by Experimental Validation, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Numerical cavitation modeling capability is critical in the design of liquid rocket engine turbopumps, feed lines, injector manifolds and engine test facilities....

Protobacco Media Exposure and Youth Susceptibility to Smoking Cigarettes, Cigarette Experimentation, and Current Tobacco Use among US Youth.

Directory of Open Access Journals (Sweden)

Erika B Fulmer

Full Text Available Youth are exposed to many types of protobacco influences, including smoking in movies, which has been shown to cause initiation. This study investigates associations between different channels of protobacco media and susceptibility to smoking cigarettes, cigarette experimentation, and current tobacco use among US middle and high school students.By using data from the 2012 National Youth Tobacco Survey, structural equation modeling was performed in 2013. The analyses examined exposure to tobacco use in different channels of protobacco media on smoking susceptibility, experimentation, and current tobacco use, accounting for perceived peer tobacco use.In 2012, 27.9% of respondents were never-smokers who reported being susceptible to trying cigarette smoking. Cigarette experimentation increased from 6.3% in 6th grade to 37.1% in 12th grade. Likewise, current tobacco use increased from 5.2% in 6th grade to 33.2% in 12th grade. Structural equation modeling supported a model in which current tobacco use is associated with exposure to static advertising through perception of peer use, and by exposure to tobacco use depicted on TV and in movies, both directly and through perception of peer use. Exposure to static advertising appears to directly increase smoking susceptibility but indirectly (through increased perceptions of peer use to increase cigarette experimentation. Models that explicitly incorporate peer use as a mediator can better discern the direct and indirect effects of exposure to static advertising on youth tobacco use initiation.These findings underscore the importance of reducing youth exposure to smoking in TV, movies, and static advertising.

Experimental Observation of a Current-Driven Instability in a Neutral Electron-Positron Beam

Science.gov (United States)

Warwick, J.; Dzelzainis, T.; Dieckmann, M. E.; Schumaker, W.; Doria, D.; Romagnani, L.; Poder, K.; Cole, J. M.; Alejo, A.; Yeung, M.; Krushelnick, K.; Mangles, S. P. D.; Najmudin, Z.; Reville, B.; Samarin, G. M.; Symes, D. D.; Thomas, A. G. R.; Borghesi, M.; Sarri, G.

2017-11-01

We report on the first experimental observation of a current-driven instability developing in a quasineutral matter-antimatter beam. Strong magnetic fields (≥1 T ) are measured, via means of a proton radiography technique, after the propagation of a neutral electron-positron beam through a background electron-ion plasma. The experimentally determined equipartition parameter of ɛB≈10-3 is typical of values inferred from models of astrophysical gamma-ray bursts, in which the relativistic flows are also expected to be pair dominated. The data, supported by particle-in-cell simulations and simple analytical estimates, indicate that these magnetic fields persist in the background plasma for thousands of inverse plasma frequencies. The existence of such long-lived magnetic fields can be related to analog astrophysical systems, such as those prevalent in lepton-dominated jets.

The Interface of IT Capabilities and Disruptive Innovations

DEFF Research Database (Denmark)

Baiyere, Abayomi

2017-01-01

The occurrence of disruptive innovations tends to challenge the fabric, structure and capability that define firms facing their threat. Prior research indicates that the capacity of a firm to restructure and reconfigure its resources to face/leverage such turbulent situations is dependent on how...... well it can orchestrate its capabilities. Although IT capability has been identified as one of the essential capability of today’s organisations, managers as well as researchers are yet to uncover the dynamics through which an organisation’s IT capability can be leveraged in disruptive innovation...... situations. This paper contributes to our understanding in this direction by conceptually exploring the different roles of an organisation's IT capabilitiy in disruptive innovation scenarios. The paper provides a synthesis of the current state of knowledge about both concepts and extends this to highlight...

Accelerator and Electrodynamics Capability Review

International Nuclear Information System (INIS)

Jones, Kevin W.

2010-01-01

Los Alamos National Laboratory (LANL) uses capability reviews to assess the science, technology and engineering (STE) quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). Laboratory Management will use this report for STE assessment and planning. LANL has defined fifteen STE capabilities. Electrodynamics and Accelerators is one of the seven STE capabilities that LANL Management (Director, PADSTE, technical Associate Directors) has identified for review in Fiscal Year (FY) 2010. Accelerators and electrodynamics at LANL comprise a blend of large-scale facilities and innovative small-scale research with a growing focus on national security applications. This review is organized into five topical areas: (1) Free Electron Lasers; (2) Linear Accelerator Science and Technology; (3) Advanced Electromagnetics; (4) Next Generation Accelerator Concepts; and (5) National Security Accelerator Applications. The focus is on innovative technology with an emphasis on applications relevant to Laboratory mission. The role of Laboratory Directed Research and Development (LDRD) in support of accelerators/electrodynamics will be discussed. The review provides an opportunity for interaction with early career staff. Program sponsors and customers will provide their input on the value of the accelerator and electrodynamics capability to the Laboratory mission.

Accelerator and electrodynamics capability review

Energy Technology Data Exchange (ETDEWEB)

Jones, Kevin W [Los Alamos National Laboratory

2010-01-01

Los Alamos National Laboratory (LANL) uses capability reviews to assess the science, technology and engineering (STE) quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). Laboratory Management will use this report for STE assessment and planning. LANL has defined fifteen STE capabilities. Electrodynamics and Accelerators is one of the seven STE capabilities that LANL Management (Director, PADSTE, technical Associate Directors) has identified for review in Fiscal Year (FY) 2010. Accelerators and electrodynamics at LANL comprise a blend of large-scale facilities and innovative small-scale research with a growing focus on national security applications. This review is organized into five topical areas: (1) Free Electron Lasers; (2) Linear Accelerator Science and Technology; (3) Advanced Electromagnetics; (4) Next Generation Accelerator Concepts; and (5) National Security Accelerator Applications. The focus is on innovative technology with an emphasis on applications relevant to Laboratory mission. The role of Laboratory Directed Research and Development (LDRD) in support of accelerators/electrodynamics will be discussed. The review provides an opportunity for interaction with early career staff. Program sponsors and customers will provide their input on the value of the accelerator and electrodynamics capability to the Laboratory mission.

Experimental investigation of flooding in air-water counter-current flow with a vertical adiabatic multi-rod bundle

International Nuclear Information System (INIS)

Chung, Bub Dong; Kim, Hho Jung; Cha, Jong Hee; Cho, Sung Jae; Chun, Moon Hyun

1991-01-01

The process of flooding phenomenon in a vertical adiabatic 3 x 3 tube bundle flow channel has been studied experimentally. A series of tests was performed, using three types of tube bundle differing only in the number of spacer grids attached, to investigate the effects of spacer grids and multi-flow channel interactions on the air-water counter-current flow limitations. Experimentally determined flooding points at various water film Reynolds numbers for three different test sections are presented in graphical form and compared with entrainment criterion for co-current flow and instability criteria. In addition, empirical flooding correlations of the Kutateladze type are obtained for each type of test section using liquid penetration data

Nuclear Data Needs and Capabilities for Applications

International Nuclear Information System (INIS)

Brown, D.

2015-01-01

In July 2014, DOE NP carried out a review of the US Nuclear Data Program. This led to several recommendations, including that the USNDP should 'devise effective and transparent mechanisms to solicit input and feedback from all stakeholders on nuclear data needs and priorities. The review also recommended that USNDP pursue experimental activities of relevance to nuclear data; the revised 2014 Mission Statement accordingly states that the USNDP uses 'targeted experimental studies' to address gaps in nuclear data. In support of these recommendations, DOE NP requested that USNDP personnel organize a Workshop on Nuclear Data Needs and Capabilities for Applications (NDNCA). This Workshop was held at Lawrence Berkeley National Laboratory (LBNL) on 27-29 May 2015. The goal of the NDNCA Workshop was to compile nuclear data needs across a wide spectrum of applied nuclear science, and to provide a summary of associated capabilities (accelerators, reactors, spectrometers, etc.) available for the required measurements. The first two days of the workshop consisted of 25 plenary talks by speakers from 16 different institutions, on Nuclear Energy, national security (NS), isotope production (IP), and industrial applications (IA). There were also shorter 'capabilities' talks that described the experimental facilities and instrumentation available for the measurement of nuclear data. This was followed by a third day of topic-specific 'breakout' sessions and a final closeout session. The agenda and copies of these talks are available online at http://bang.berkeley.edu/events/NDNCA/agenda. The importance of nuclear data to both basic and applied nuclear science was reflected in the fact that while the impetus for the workshop arose from the 2014 USNDP review, joint sponsorship for the workshop was provided by the Nuclear Science and Security Consortium, a UC-Berkeley based organization funded by the National Nuclear Security Administration (NNSA).

Analysing Leontiev Tube Capabilities in the Space-based Plants

Directory of Open Access Journals (Sweden)

N. L. Shchegolev

2017-01-01

Full Text Available The paper presents a review of publications dedicated to the gas-dynamic temperature stratification device (the Leontief tube and shows main factors affecting its efficiency. Describes an experimental installation, which is used to obtain data on the value of energy separation in the air to prove this device the operability.The assumption that there is an optimal relationship between the flow velocities in the subsonic and supersonic channels of the gas-dynamic temperature stratification device is experimentally confirmed.The paper conducts analysis of possible ways to raise the efficiency of power plants of various (including space basing, and shows that, currently, a mainstream of increasing efficiency of their operation is to complicate design solutions.A scheme of the closed gas-turbine space-based plant using a mixture of inert gases (helium-xenon one for operation is proposed. What differs it from the simplest variants is a lack of the cooler-radiator and integration into gas-dynamic temperature stratification device and heat compressor.Based on the equations of one-dimensional gas dynamics, it is shown that the total pressure restorability when removing heat in a thermal compressor determines operating capability of this scheme. The exploratory study of creating a heat compressor is performed, and it is shown that when operating on gases with a Prandtl number close to 1, the total pressure does not increase.The operating capability conditions of the heat compressor are operation on gases with a low value of the Prandtl number (helium-xenon mixture at high supersonic velocities and with a longitudinal pressure gradient available.It is shown that there is a region of the low values of the Prandtl number (Pr <0.3 for which, with the longitudinal pressure gradient available in the supersonic flows of a viscous gas, the total pressure can be restored.

Structural Capability of an Organization toward Innovation Capability

DEFF Research Database (Denmark)

Nielsen, Susanne Balslev; Momeni, Mostafa

2016-01-01

The scholars in the field of strategic management have developed two major approaches for attainment of competitive advantage: an approach based on environmental opportunities, and another one based on internal capabilities of an organization. Some investigations in the last two decades have...... indicated that the advantages relying on the internal capabilities of organizations may determine the competitive position of organizations better than environmental opportunities do. Characteristics of firms shows that one of the most internal capabilities that lead the organizations to the strongest...... competitive advantage in the organizations is the innovation capability. The innovation capability is associated with other organizational capabilities, and many organizations have focused on the need to identify innovation capabilities.This research focuses on recognition of the structural aspect...

A finite difference method for numerical solution of the Nernst-Planck equations when convective flux and electric current are involved

International Nuclear Information System (INIS)

Aguilera, V.M.; Garrido, J.; Mafe, S.; Pellicer, J.

1985-01-01

An algorithm for the solution of Nernst-Planck equations with simultaneous convective flux and electric current has been developed without using Poisson's equation. The numerical simulation which has been developed reproduces the behaviour of the system employing their experimental variables as parameters of the algorithm. However, other procedures are only capable of dealing with some of the experimental conditions described here. The agreement between the theoretically predicted values and the experimentally obtained is quite reasonable. (author)

SPHINX experimenters information package

International Nuclear Information System (INIS)

Zarick, T.A.

1996-08-01

This information package was prepared for both new and experienced users of the SPHINX (Short Pulse High Intensity Nanosecond X-radiator) flash X-Ray facility. It was compiled to help facilitate experiment design and preparation for both the experimenter(s) and the SPHINX operational staff. The major areas covered include: Recording Systems Capabilities,Recording System Cable Plant, Physical Dimensions of SPHINX and the SPHINX Test cell, SPHINX Operating Parameters and Modes, Dose Rate Map, Experiment Safety Approval Form, and a Feedback Questionnaire. This package will be updated as the SPHINX facilities and capabilities are enhanced

The Virtual Ship - A New Capability in Support of Maritime Forces

National Research Council Canada - National Science Library

Best, John

1999-01-01

...) systems, weapons and the platform itself. There is currently a gap in the capability to rigorously study these integration requirements in a laboratory environment Additionally, the capability is lacking to comprehensively investigate...

Developing a Current Capability Design for Manufacture Framework in the Aerospace Industry

OpenAIRE

Whiteside, A.; Shehab, Essam; Beadle, C.; Percival, M.

2009-01-01

Organised by: Cranfield University During progressive product design and development in the aerospace industry, a lack of effective communication between the sequential functions of design, manufacturing and assembly often causes delays and setbacks whereby production capabilities are unable to realise design intent in high-complexity product models. As a result, there is a need to formalise the progressive release of an engineering model to production functions during New Prod...

Experimental Observation of a Current-Driven Instability in a Neutral Electron-Positron Beam.

Science.gov (United States)

Warwick, J; Dzelzainis, T; Dieckmann, M E; Schumaker, W; Doria, D; Romagnani, L; Poder, K; Cole, J M; Alejo, A; Yeung, M; Krushelnick, K; Mangles, S P D; Najmudin, Z; Reville, B; Samarin, G M; Symes, D D; Thomas, A G R; Borghesi, M; Sarri, G

2017-11-03

We report on the first experimental observation of a current-driven instability developing in a quasineutral matter-antimatter beam. Strong magnetic fields (≥1  T) are measured, via means of a proton radiography technique, after the propagation of a neutral electron-positron beam through a background electron-ion plasma. The experimentally determined equipartition parameter of ε_{B}≈10^{-3} is typical of values inferred from models of astrophysical gamma-ray bursts, in which the relativistic flows are also expected to be pair dominated. The data, supported by particle-in-cell simulations and simple analytical estimates, indicate that these magnetic fields persist in the background plasma for thousands of inverse plasma frequencies. The existence of such long-lived magnetic fields can be related to analog astrophysical systems, such as those prevalent in lepton-dominated jets.

RIA testing capability of the transient reactor test facility

International Nuclear Information System (INIS)

Crawford, D.C.; Swanson, R.W.

1999-01-01

The advent of high-burnup fuel implementation in LWRs has generated international interest in high-burnup LWR fuel performance. Recent testing under simulated RIA conditions has demonstrated that certain fuel designs fail at peak fuel enthalpy values that are below existing regulatory criteria. Because many of these tests were performed with non-prototypically aggressive test conditions (i.e., with power pulse widths less than 10 msec FWHM and with non-protoypic coolant configurations), the results (although very informative) do not indisputably identify failure thresholds and fuel behavior. The capability of the TREAT facility to perform simulated RIA tests with prototypic test conditions is currently being evaluated by ANL personnel. TREAT was designed to accommodate test loops and vehicles installed for in-pile transient testing. During 40 years of TREAT operation and fuel testing and evaluation, experimenters have been able to demonstrate and determine the transient behavior of several types of fuel under a variety of test conditions. This experience led to an evolution of test methodology and techniques which can be employed to assess RIA behavior of LWR fuel. A pressurized water loop that will accommodate RIA testing of LWR and CANDU-type fuel has completed conceptual design. Preliminary calculations of transient characteristics and energy deposition into test rods during hypothetical TREAT RIA tests indicate that with the installation of a pressurized water loop, the facility is quite capable of performing prototypic RIA testing. Typical test scenarios indicate that a simulated RIA with a 72 msec FWHM pulse width and energy deposition of 1200 kJ/kg (290 cal/gm) is possible. Further control system enhancements would expand the capability to pulse widths as narrow as 40 msec. (author)

Mixed-mode chaotic circuit with Wien-bridge configuration: The results of experimental verification

International Nuclear Information System (INIS)

Kilic, Recai

2007-01-01

In this paper, we deal with the experimentally implementation of inductorless Wien bridge-based mixed-mode chaotic circuit (MMCC) which is capable to exhibit both linear and nonlinear oscillations. The results of experimental implementation agree with the results of theoretical and computer simulation presented in literature. Since the proposed implementation of MMCC circuit uses different design blocks such as Wien bridge-based autonomous circuit part, CFOA (current feedback operational amplifier)-based floating inductance simulator, CFOA-based Chua's diode and switching mechanism, it offers very versatile chaotic circuit model for studying autonomous and nonautonomous chaotic dynamics

Toward Vision Oriented Organization through Foresight Capability Development

Directory of Open Access Journals (Sweden)

Gianita BLEOJU

2014-11-01

Full Text Available Dealing with complexity is becoming increasingly difficult for organizations, due to limited replicable abilities, once management performance was remunerated by successful decisions on the marketplace. The competitive advantage, based upon current documented organizational management expertise, deployed into patterns of competitive behavior, prove to be unsustainable. Therefore, we assist to a relative emergency of strategic intelligence adjustment framework, to channel the managerial capability mechanisms, from current detective orientation capabilities toward anticipatory ones. Based upon exploitation of an organizational profiling database, we try our contribution to this challenging debate, by formulating recommendations for strategic adjustment and prototype testing of the potential solutions, through a designed transition matrix from market oriented to vision oriented organizations.

Post Irradiation Capabilities at the Idaho National Laboratory

International Nuclear Information System (INIS)

Schulthess, J.L.; Rosenberg, K.E.

2011-01-01

The U.S. Department of Energy (DOE), Office of Nuclear Energy (NE) oversees the efforts to ensure nuclear energy remains a viable option for the United States. A significant portion of these efforts are related to post-irradiation examinations (PIE) of highly activated fuel and materials that are subject to the extreme environment inside a nuclear reactor. As the lead national laboratory, Idaho National Laboratory (INL) has a rich history, experience, workforce and capabilities for performing PIE. However, new advances in tools and techniques for performing PIE now enable understanding the performance of fuels and materials at the nano-scale and smaller level. Examination at this level is critical since this is the scale at which irradiation damage occurs. The INL is on course to adopt these advanced tools and techniques to develop a comprehensive nuclear fuels and materials characterization capability that is unique in the world. Because INL has extensive PIE capabilities currently in place, a strong foundation exist to build upon as new capabilities are implemented and work load increases. In the recent past, INL has adopted significant capability to perform advanced PIE characterization. Looking forward, INL is planning for the addition of two facilities that will be built to meet the stringent demands of advanced tools and techniques for highly activated fuels and materials characterization. Dubbed the Irradiated Materials Characterization Laboratory (IMCL) and Advanced Post Irradiation Examination Capability, these facilities are next generation PIE laboratories designed to perform the work of PIE that cannot be performed in current DOE facilities. In addition to physical capabilities, INL has recently added two significant contributors to the Advanced Test Reactor-National Scientific User Facility (ATR-NSUF), Oak Ridge National Laboratory and University of California, Berkeley.

The Experimental Measurement of Aerodynamic Heating About Complex Shapes at Supersonic Mach Numbers

Science.gov (United States)

Neumann, Richard D.; Freeman, Delma C.

2011-01-01

In 2008 a wind tunnel test program was implemented to update the experimental data available for predicting protuberance heating at supersonic Mach numbers. For this test the Langley Unitary Wind Tunnel was also used. The significant differences for this current test were the advances in the state-of-the-art in model design, fabrication techniques, instrumentation and data acquisition capabilities. This current paper provides a focused discussion of the results of an in depth analysis of unique measurements of recovery temperature obtained during the test.

System Reliability Analysis Capability and Surrogate Model Application in RAVEN

Energy Technology Data Exchange (ETDEWEB)

Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alfonsi, Andrea [Idaho National Lab. (INL), Idaho Falls, ID (United States); Huang, Dongli [Idaho National Lab. (INL), Idaho Falls, ID (United States); Gleicher, Frederick [Idaho National Lab. (INL), Idaho Falls, ID (United States); Wang, Bei [Idaho National Lab. (INL), Idaho Falls, ID (United States); Adbel-Khalik, Hany S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pascucci, Valerio [Idaho National Lab. (INL), Idaho Falls, ID (United States); Smith, Curtis L. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-11-01

This report collect the effort performed to improve the reliability analysis capabilities of the RAVEN code and explore new opportunity in the usage of surrogate model by extending the current RAVEN capabilities to multi physics surrogate models and construction of surrogate models for high dimensionality fields.

Methodological Individualism and the Organizational Capabilities Approach

DEFF Research Database (Denmark)

Felin, Teppo; Foss, Nicolai Juul

2004-01-01

AbstractDuring the last decade, strategy scholars have increasingly converged on organizationalcapabilities as a key construct in strategy research. We explicate some of the underlying,unstated assumptions of current capabilities-based work by drawing on seminal work in thephilosophy of social...... critical individual-levelconsiderations, including individual action and heterogeneity. In this note we do not denyor reject the notion of routines or capabilities per se, but rather call for an increasedemphasis on how these collective structures originate and change as a result of individualactions...

NOAA NOS SOS, EXPERIMENTAL - Currents

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA NOS SOS server is part of the IOOS DIF SOS Project. The stations in this dataset have currents data. *These services are for testing and evaluation use...

Atmospheric Release Advisory Capability

International Nuclear Information System (INIS)

Dickerson, M.H.; Gudiksen, P.H.; Sullivan, T.J.

1983-02-01

The Atmospheric Release Advisory Capability (ARAC) project is a Department of Energy (DOE) sponsored real-time emergency response service available for use by both federal and state agencies in case of a potential or actual atmospheric release of nuclear material. The project, initiated in 1972, is currently evolving from the research and development phase to full operation. Plans are underway to expand the existing capability to continuous operation by 1984 and to establish a National ARAC Center (NARAC) by 1988. This report describes the ARAC system, its utilization during the past two years, and plans for its expansion during the next five to six years. An integral part of this expansion is due to a very important and crucial effort sponsored by the Defense Nuclear Agency to extend the ARAC service to approximately 45 Department of Defense (DOD) sites throughout the continental US over the next three years

Transformerless photovoltaic inverters with leakage current and pulsating power elimination

DEFF Research Database (Denmark)

Tang, Yi; Yao, Wenli; Wang, H.

2015-01-01

This paper presents a transformerless inverter topology, which is capable of simultaneously solving leakage current and pulsating power issues in grid-connected photovoltaic (PV) systems. Without adding any additional components to the system, the leakage current caused by the PV......-to-ground parasitic capacitance can be bypassed by introducing a common mode (CM) conducting path to the inverter. The resulting ground leakage current is therefore well controlled to be below the regulation limit. Moreover, the proposed inverter can also eliminate the well-known double line frequency pulsating power....... The mechanism of leakage current suppression and the closed-loop control of pulsating power decoupling are discussed in the paper in details. A 500 W prototype was also built and tested in the laboratory, and both simulation and experimental results are finally presented to show the excellent performance...

Finite element analysis of ageing reinforced and prestressed concrete structures in nuclear plant - An international review of current capabilities and priorities for future developments

International Nuclear Information System (INIS)

2002-01-01

Nuclear plants contain a variety of concrete structures whose structural performance is essential to the safety of the plant. There is a requirement to demonstrate the robustness of these structures during normal operating and extreme accident conditions, throughout their life. During this time, the concrete may degrade due to the effects of ageing. This degradation must be accounted for during the assessment of their performance. Finite Element Analysis (FEA) techniques have tremendous potential for providing valuable insight into the behaviour of these aged concrete structures under a range of different loading conditions. Advanced FEA techniques currently enjoy widespread use within the nuclear industry for the non-linear analysis of concrete. Many practitioners within the nuclear industry are at the forefront of the industrial application of these methods. However, in some areas, the programs that are commercially available lag behind the best information available from research. This document is an international review of current capabilities and priorities for future development relating to non-linear finite element analysis of reinforced and prestressed concrete in the nuclear industry in the various member states. Particular attention is paid to the analysis of degraded or ageing structures. This report: 1. Summarises the needs for FEA of aged concrete nuclear structures; 2. Details the existing capabilities, not just in terms of what the software is capable of, but also in terms of the current practices employed by those in industry; 3. Looks at how engineers, within the nuclear industry, working in this field would like to see methods improved, and identifies the factors that are limiting current practice; 4. Summarises ongoing research that may provide beneficial technological advances; 5. Assigns priorities to the different development requests; 6. Selects those developments that are felt to be of greatest benefit to industry and provides a qualitative

Experimental device, corresponding forward model and processing of the experimental data using wavelet analysis for tomographic image reconstruction applied to eddy current nondestructive evaluation

International Nuclear Information System (INIS)

Joubert, P.Y.; Madaoui, N.

1999-01-01

In the context of eddy current non destructive evaluation using a tomographic image reconstruction process, the success of the reconstruction depends not only on the choice of the forward model and of the inversion algorithms, but also on the ability to extract the pertinent data from the raw signal provided by the sensor. We present in this paper, an experimental device designed for imaging purposes, the corresponding forward model, and a pre-processing of the experimental data using wavelet analysis. These three steps implemented with an inversion algorithm, will allow in the future to perform image reconstruction of 3-D flaws. (authors)

SuperMAG: Present and Future Capabilities

Science.gov (United States)

Hsieh, S. W.; Gjerloev, J. W.; Barnes, R. J.

2009-12-01

SuperMAG is a global collaboration that provides ground magnetic field perturbations from a long list of stations in the same coordinate system, identical time resolution and with a common baseline removal approach. This unique high quality dataset provides a continuous and nearly global monitoring of the ground magnetic field perturbation. Currently, only archived data are available on the website and hence it targets basic research without any operational capabilities. The existing SuperMAG software can be easily adapted to ingest real-time or near real-time data and provide a now-casting capability. The SuperDARN program has a long history of providing near real-time maps of the northern hemisphere electrostatic potential and as both SuperMAG and SuperDARN share common software it is relatively easy to adapt these maps for global magnetic perturbations. Magnetometer measurements would be assimilated by the SuperMAG server using a variety of techniques, either by downloading data at regular intervals from remote servers or by real-time streaming connections. The existing SuperMAG analysis software would then process these measurements to provide the final calibrated data set using the SuperMAG coordinate system. The existing plotting software would then be used to produce regularly updated global plots. The talk will focus on current SuperMAG capabilities illustrating the potential for now-casting and eventually forecasting.

Capabilities for measuring physical and chemical properties of rocks at high pressure

Energy Technology Data Exchange (ETDEWEB)

Durham, W.B. (comp.)

1990-01-01

The Experimental Geophysics Group of the Earth Sciences Department at Lawrence Livermore National Laboratory (LLNL) has experimental equipment that measures a variety of physical properties and phase equilibria and kinetics on rocks and minerals at extreme pressures (to 500 GPa) and temperatures (from 10 to 2800 K). These experimental capabilities are described in this report in terms of published results, photographs, and schematic diagrams.

Experimental Products Development Team (EPDT) Supporting New AWIPS . Part 2; Capabilities

Science.gov (United States)

Burks, Jason E.

2015-01-01

In 2012, the Experimental Products Development Team (EPDT) was formed within NASA's Short-term Prediction Research and Transition (SPoRT) Center to create training for development of plug-ins to extend the National Weather Service (NWS) Advanced Weather Interactive Processing System (AWIPS) version 2. The broader atmospheric science community had a need for AWIPS II development training being created at SPoRT and EPDT was expanded to include other groups who were looking for training. Since the expansion of the group occurred, EPDT has provided AWIPS II development training to over thirty participants spanning a wide variety of groups such as NWS Systems Engineering Center, NWS Meteorological Development Laboratory, and several NOAA Cooperative Institutes. Participants within EPDT solidify their learning experience through hands-on learning and by participating in a "code-sprint" in which they troubleshoot existing and develop plug-ins. The hands-on learning workshop is instructor lead with participants completing exercises within the AWIPS II Development Environment. During the code sprints EPDT groups work on projects important to the community and have worked on various plug-ins such as an RGB image recipe creation tool, and an mPing (crowd sourced precipitation type reporting system) ingest and display. EPDT has developed a well-defined training regime which prepares participants to fully develop plug-ins for the extendible AWIPS II architecture from ingest to the display of new data. SPoRT has hosted 2 learning workshops and 1 code sprint over the last two years, and continues to build and shape the EPDT group based on feedback from previous workshops. The presentation will provide an overview of EPDT current and future activities, and best practices developed within EPDT.

Active power compensator of the current harmonics based on the instantaneous power theory

Directory of Open Access Journals (Sweden)

Marian GAICEANU

2005-12-01

Full Text Available The quality of the electrical current becomes a major concern. The proliferation of the power electronic converters, which are used extensively to control electrical apparatus in industrial and commercial applications (dc and ac variable speed motor drives, induction furnaces, power line conditioners, and industrial power supplies, is at the origin of the AC current distribution network pollution and the reactive power demand. These power electronic converters typically draw non-sinusoidal currents from the utility, causing interference with adjacent sensitive loads and limit the utilization of the available electrical supply. The quality of the electrical current thus becomes a significant concern for the distributors of energy and their customers. Recent progress as regards technology of the power electronics brings a capacity of compensation and correction of the harmonic distortion generated by the nonlinear loads. In this paper a parallel active filter prototype capable of reducing the total harmonic distortion in the supply for most current source or adjustable speed drive type loads is presented. A 33 kVA active power filter was developed for harmonic and reactive power compensation based on the instantaneous power theory. The active filter configuration requires the measurement of both the load and filter currents. Experimental results from a prototype active power filter confirm the suitability of the proposed approach. The actual 33kVA prototype converter has been built and tested in the SIEI S.p.A. (Italy laboratory under the Marie Curie Post Doctoral research. The active power compensator is controlled by a high performance DSP platform, resulting in the following active filter features: source current reduction up to the 25th harmonic, 10% THD achievable for current source type loads, efficiency above 97%, does not cause resonance with other loads, operation in the presence of unbalanced loads, reactive power and harmonics

Pulse Power Capability Estimation of Lithium Titanate Oxide-based Batteries

DEFF Research Database (Denmark)

Stroe, Ana-Irina; Swierczynski, Maciej Jozef; Stroe, Daniel Loan

2016-01-01

The pulse power capability (PPC) represents one of the parameters that describe the performance behavior of Lithium-ion batteries independent on the application. Consequently, extended information about the Li-ion battery PPC and its dependence on the operating conditions become necessary. Thus......, this paper analyzes the power capability characteristic of a 13Ah high power Lithium Titanate Oxide-based battery and its dependence on temperature, load current and state-of-charge. Furthermore, a model to predict the discharging PPC of the battery cell at different temperatures and load currents for three...

The new MCNP6 depletion capability

International Nuclear Information System (INIS)

Fensin, M. L.; James, M. R.; Hendricks, J. S.; Goorley, J. T.

2012-01-01

The first MCNP based in-line Monte Carlo depletion capability was officially released from the Radiation Safety Information and Computational Center as MCNPX 2.6.0. Both the MCNP5 and MCNPX codes have historically provided a successful combinatorial geometry based, continuous energy, Monte Carlo radiation transport solution for advanced reactor modeling and simulation. However, due to separate development pathways, useful simulation capabilities were dispersed between both codes and not unified in a single technology. MCNP6, the next evolution in the MCNP suite of codes, now combines the capability of both simulation tools, as well as providing new advanced technology, in a single radiation transport code. We describe here the new capabilities of the MCNP6 depletion code dating from the official RSICC release MCNPX 2.6.0, reported previously, to the now current state of MCNP6. NEA/OECD benchmark results are also reported. The MCNP6 depletion capability enhancements beyond MCNPX 2.6.0 reported here include: (1) new performance enhancing parallel architecture that implements both shared and distributed memory constructs; (2) enhanced memory management that maximizes calculation fidelity; and (3) improved burnup physics for better nuclide prediction. MCNP6 depletion enables complete, relatively easy-to-use depletion calculations in a single Monte Carlo code. The enhancements described here help provide a powerful capability as well as dictate a path forward for future development to improve the usefulness of the technology. (authors)

The New MCNP6 Depletion Capability

International Nuclear Information System (INIS)

Fensin, Michael Lorne; James, Michael R.; Hendricks, John S.; Goorley, John T.

2012-01-01

The first MCNP based inline Monte Carlo depletion capability was officially released from the Radiation Safety Information and Computational Center as MCNPX 2.6.0. Both the MCNP5 and MCNPX codes have historically provided a successful combinatorial geometry based, continuous energy, Monte Carlo radiation transport solution for advanced reactor modeling and simulation. However, due to separate development pathways, useful simulation capabilities were dispersed between both codes and not unified in a single technology. MCNP6, the next evolution in the MCNP suite of codes, now combines the capability of both simulation tools, as well as providing new advanced technology, in a single radiation transport code. We describe here the new capabilities of the MCNP6 depletion code dating from the official RSICC release MCNPX 2.6.0, reported previously, to the now current state of MCNP6. NEA/OECD benchmark results are also reported. The MCNP6 depletion capability enhancements beyond MCNPX 2.6.0 reported here include: (1) new performance enhancing parallel architecture that implements both shared and distributed memory constructs; (2) enhanced memory management that maximizes calculation fidelity; and (3) improved burnup physics for better nuclide prediction. MCNP6 depletion enables complete, relatively easy-to-use depletion calculations in a single Monte Carlo code. The enhancements described here help provide a powerful capability as well as dictate a path forward for future development to improve the usefulness of the technology.

Research of Steel-dielectric Transition Using Subminiature Eddy-current Transducer

Science.gov (United States)

Dmitriev, S. F.; Malikov, V. N.; Sagalakov, A. M.; Ishkov, A. V.

2018-05-01

The research aims to develop a subminiature transducer for electrical steel investigation. The authors determined the capability to study steel characteristics at different depths based on variations of eddy-current transducer amplitude at the steel-dielectric boundary. A subminiature transformer-type transducer was designed, which enables to perform local investigations of ferromagnetic materials using an eddy-current method based on local studies of the steel electrical conductivity. Having the designed transducer as a basis, a hardware-software complex was built to perform experimental studies of steel at the interface boundary. Test results are reported for a specimen with continuous and discrete measurements taken at different frequencies. The article provides the key technical information about the eddy current transformer used and describes the methodology of measurements that makes it possible to control steel to dielectric transition.

Researching pharmacist managerial capability: philosophical perspectives and paradigms of inquiry.

Science.gov (United States)

Woods, Phillip; Gapp, Rod; King, Michelle A

2015-01-01

In successful community pharmacy business enterprises suitably responsive actions to meet ever-increasing change require capable pharmacy managers who readily learn and adapt. Capability as a concept is generally understood to be the ability of a manager to identify and act to solve unfamiliar problems in unfamiliar situations. Capability is characterized by adaptability and flexibility. However, different understandings of the concept 'capability' and what it means to be 'capable' are indirect and incomplete. This paper aims to clarify current theories regarding the concept of 'capability' at the level of the individual, and through this to make more explicit what is known about the phenomenon, but more particularly, how we know what we know. The analysis includes the concept of 'competence' because explanations of capability include competence, and the two concepts are not clearly separated in the literature. By probing the epistemological origins of current theory concerning both concepts, the limiting taken for granted assumptions are revealed. Assumptions about context and time, and the psychological theory through which individuals are assumed to perceive, know and learn, are illuminated. The analysis, in connection with the literature, shows how the interpretive philosophic research approach may reveal a different and useful theoretical perspective for explaining capability as a dynamic performance. It is suggested that such a perspective may narrow the gap between the theory of capability and its practice. The interpretive perspective holds potential to reveal how capability, as performed by successful community pharmacy managers, might be further researched and strengthened. This paper supports the challenging suggestion that pharmacy social research needs to rebalance the dominance of purely empirical research by exploring interpretive methodologies to better understand human actions and relations in the context of pharmacy. Crown Copyright © 2015

Simple process capability analysis and quality validation of ...

African Journals Online (AJOL)

Many ways can be applied to improve the process and one of them is by choosing the correct six sigma's design of experiment (DOE). In this study, Taguchi's experimental design was applied to achieve high percentage of cell viability in the fermentation experiment. The process capability of this study was later analyzed by ...

Location estimation of approaching objects is modulated by the observer's inherent and momentary action capabilities

NARCIS (Netherlands)

Kandula, Manasa; Hofman, Dennis; Dijkerman, H Chris

2016-01-01

Action capability may be one of the factors that can influence our percept of the world. A distinction can be made between momentary action capability (action capability at that particular moment) and inherent action capability (representing a stable action capability). In the current study, we

Off-Gas Adsorption Model Capabilities and Recommendations

Energy Technology Data Exchange (ETDEWEB)

Lyon, Kevin L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Welty, Amy K. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Law, Jack [Idaho National Lab. (INL), Idaho Falls, ID (United States); Ladshaw, Austin [Georgia Inst. of Technology, Atlanta, GA (United States); Yiacoumi, Sotira [Georgia Inst. of Technology, Atlanta, GA (United States); Tsouris, Costas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-03-01

Off-gas treatment is required to reduce emissions from aqueous fuel reprocessing. Evaluating the products of innovative gas adsorption research requires increased computational simulation capability to more effectively transition from fundamental research to operational design. Early modeling efforts produced the Off-Gas SeParation and REcoverY (OSPREY) model that, while efficient in terms of computation time, was of limited value for complex systems. However, the computational and programming lessons learned in development of the initial model were used to develop Discontinuous Galerkin OSPREY (DGOSPREY), a more effective model. Initial comparisons between OSPREY and DGOSPREY show that, while OSPREY does reasonably well to capture the initial breakthrough time, it displays far too much numerical dispersion to accurately capture the real shape of the breakthrough curves. DGOSPREY is a much better tool as it utilizes a more stable set of numerical methods. In addition, DGOSPREY has shown the capability to capture complex, multispecies adsorption behavior, while OSPREY currently only works for a single adsorbing species. This capability makes DGOSPREY ultimately a more practical tool for real world simulations involving many different gas species. While DGOSPREY has initially performed very well, there is still need for improvement. The current state of DGOSPREY does not include any micro-scale adsorption kinetics and therefore assumes instantaneous adsorption. This is a major source of error in predicting water vapor breakthrough because the kinetics of that adsorption mechanism is particularly slow. However, this deficiency can be remedied by building kinetic kernels into DGOSPREY. Another source of error in DGOSPREY stems from data gaps in single species, such as Kr and Xe, isotherms. Since isotherm data for each gas is currently available at a single temperature, the model is unable to predict adsorption at temperatures outside of the set of data currently

Axial mercury segregation in direct current operated low-pressure argon-mercury gas discharge: Part I. Experimental

NARCIS (Netherlands)

Gielen, J.W.A.M.; de Groot, S.; Dijk, van J.; Mullen, van der J.J.A.M.

2004-01-01

Due to cataphoresis, axial segregation of mercury will occur when the gas discharge of a fluorescent lamp is operated by means of a direct current. A consequence of this is a non-uniform axial luminance distribution along the lamp. To determine the degree of axial mercury segregation experimentally,

Recent Advances in Simulation of Eddy Current Testing of Tubes and Experimental Validations

Science.gov (United States)

Reboud, C.; Prémel, D.; Lesselier, D.; Bisiaux, B.

2007-03-01

Eddy current testing (ECT) is widely used in iron and steel industry for the inspection of tubes during manufacturing. A collaboration between CEA and the Vallourec Research Center led to the development of new numerical functionalities dedicated to the simulation of ECT of non-magnetic tubes by external probes. The achievement of experimental validations led us to the integration of these models into the CIVA platform. Modeling approach and validation results are discussed here. A new numerical scheme is also proposed in order to improve the accuracy of the model.

Mixed-mode chaotic circuit with Wien-bridge configuration: The results of experimental verification

Energy Technology Data Exchange (ETDEWEB)

Kilic, Recai [Erciyes University, Department of Electronic Engineering, 38039 Kayseri (Turkey)]. E-mail: kilic@erciyes.edu.tr

2007-05-15

In this paper, we deal with the experimentally implementation of inductorless Wien bridge-based mixed-mode chaotic circuit (MMCC) which is capable to exhibit both linear and nonlinear oscillations. The results of experimental implementation agree with the results of theoretical and computer simulation presented in literature. Since the proposed implementation of MMCC circuit uses different design blocks such as Wien bridge-based autonomous circuit part, CFOA (current feedback operational amplifier)-based floating inductance simulator, CFOA-based Chua's diode and switching mechanism, it offers very versatile chaotic circuit model for studying autonomous and nonautonomous chaotic dynamics.

Impact of Personnel Capabilities on Organizational Innovation Capability

DEFF Research Database (Denmark)

Nielsen, Susanne Balslev; Momeni, Mostafa

2016-01-01

in this rapidly changing world. This research focuses on definition of the personnel aspect of innovation capability, and proposes a conceptual model based on the scientific articles of academic literature on organisations innovation capability. This paper includes an expert based validation in three rounds...... of the Delphi method. And for the purpose of a better appreciation of the relationship dominating the factors of the model, it has distributed the questionnaire to Iranian companies in the Food industry. This research proposed a direct relationship between Innovation Capability and the Personnel Capability...

High current density M-type cathodes for vacuum electron devices

International Nuclear Information System (INIS)

Li Ji; Yu Zhiqiang; Shao Wensheng; Zhang Ke; Gao Yujuan; Yuan Haiqing; Wang Hui; Huang Kaizhi; Chen Qilue; Yan Suqiu; Cai Shaolun

2005-01-01

We investigated high current density emission capabilities of M-type cathodes used for vacuum electron devices (VEDs). The experimental results of emission and lifetime evaluating in both close-spaced diode structure and electron gun testing vehicles are given. Emission current densities measured in the diode structure at 1020 deg. C Br in the CW mode were above 10 A/cm 2 ; while in electron gun testing vehicles, emission current densities were above 8 A/cm 2 in CW mode and above 32 A/cm 2 in pulsed mode, respectively. The current density above 94 A/cm 2 has been acquired in no. 0306 electron gun vehicle while the practical temperature is 1060 deg. C Br . For a comparison some of the data from I-scandate cathodes are presented. Finally, several application examples in practical travelling wave tubes (TWTs) and multi beam klystrons (MBKs) are also reported

Development of a gamma ray spectroscopy capability at LANSCE

International Nuclear Information System (INIS)

Nelson, R.O.; Strottman, D.D.; Sterbenz, S.M.

1998-01-01

This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The goal of this project was to explore an upgrade to the GEANIE high-resolution gamma-ray spectrometer at the Los Alamos Neutron Science Center (LANSCE) to help build additional experimental capabilities. The improvements identified have significantly added to the capabilities of GEANIE and made the facility more attractive for studies supporting the core national security mission as well as for use by outside collaborators. These benefits apply to both basic and applied studies

Group Capability Model

Science.gov (United States)

Olejarski, Michael; Appleton, Amy; Deltorchio, Stephen

2009-01-01

The Group Capability Model (GCM) is a software tool that allows an organization, from first line management to senior executive, to monitor and track the health (capability) of various groups in performing their contractual obligations. GCM calculates a Group Capability Index (GCI) by comparing actual head counts, certifications, and/or skills within a group. The model can also be used to simulate the effects of employee usage, training, and attrition on the GCI. A universal tool and common method was required due to the high risk of losing skills necessary to complete the Space Shuttle Program and meet the needs of the Constellation Program. During this transition from one space vehicle to another, the uncertainty among the critical skilled workforce is high and attrition has the potential to be unmanageable. GCM allows managers to establish requirements for their group in the form of head counts, certification requirements, or skills requirements. GCM then calculates a Group Capability Index (GCI), where a score of 1 indicates that the group is at the appropriate level; anything less than 1 indicates a potential for improvement. This shows the health of a group, both currently and over time. GCM accepts as input head count, certification needs, critical needs, competency needs, and competency critical needs. In addition, team members are categorized by years of experience, percentage of contribution, ex-members and their skills, availability, function, and in-work requirements. Outputs are several reports, including actual vs. required head count, actual vs. required certificates, CGI change over time (by month), and more. The program stores historical data for summary and historical reporting, which is done via an Excel spreadsheet that is color-coded to show health statistics at a glance. GCM has provided the Shuttle Ground Processing team with a quantifiable, repeatable approach to assessing and managing the skills in their organization. They now have a common

Vacuum chamber eddy current correction coil for the AGS Booster

International Nuclear Information System (INIS)

Danby, G.; Jackson, J.

1988-01-01

The AGS Booster injector will perform a variety of functions. Heavy ion acceleration requires a bakeable, ultra-high vacuum system (VC). Acceleration for intense proton beams requires rapid cycling (B /preceq/ 10T/sec). If straight forward heavy walled VC are used, the field perturbations due to eddy currents are large. The state of the art lattice has highly distributed lumped sextupoles capable of substantially correcting the induced field nonlinearity. Nevertheless, for the very highest space charge-intensity limits, it is desirable to have the capability to remove eddy current fields at the source. Correction coils attached to the outside of the VC cancel its current aberrations over the required good field aperture. These can be passively powered by transformer action, using two turn windings around the magnet yoke. Programmed power supplies can also be used. This inexpensive additional correction option uses a three turn per quadrant coil which follows the local contour of the VC. Transverse movements of several mms of the VC will have no beam optical effect since the large field aberrations and their corrections have the same displaced coordinates. Experimental and computer studies will be presented, as well as mechanical and electrical design of a simple method of construction. 6 figs

Vacuum chamber eddy current correction coil for the AGS booster

International Nuclear Information System (INIS)

Danby, G.; Jackson, J.

1988-01-01

This paper reports on the AGS Booster injector that performs a variety of functions. Heavy ion acceleration requires a bakeable, ultra-high vacuum system (VC). Acceleration for intense proton beams requires rapid cycling (B ≤10T/sec). If straight forward heavy walled VC are used, the field perturbations due to eddy currents are large. The state of the art lattice has highly distributed lumped sextupoles capable of substantially correcting the induced field nonlinearity. Nevertheless, for the very highest space charge-intensity limits, it is desirable to have the capability to remove eddy current fields at the source. Correction coils attached to the outside of the VC cancel its current aberrations over the required good field aperture. These can be passively powered by transformer action, using two turn windings around the magnet yoke. Programmed power supplies can also be used. This inexpensive additional correction option uses a three turn per quadrant coil which follows the local contour of the VC. Transverse movements of several mms of the VC will have no beam optical effect since the large field aberrations and their corrections have the same displace coordinates. Experimental and computer studies will be presented, as well as mechanical and electrical design of a simple method of construction

Capability Paternalism

NARCIS (Netherlands)

Claassen, R.J.G.|info:eu-repo/dai/nl/269266224

A capability approach prescribes paternalist government actions to the extent that it requires the promotion of specific functionings, instead of the corresponding capabilities. Capability theorists have argued that their theories do not have much of these paternalist implications, since promoting

New simulation capabilities of electron clouds in ion beams with large tune depression

International Nuclear Information System (INIS)

Vay, J.-L.; Furman, M.A.; Seidl, P.A.

2007-01-01

We have developed a new, comprehensive set of simulation tools aimed at modeling the interaction of intense ion beams and electron clouds (e-clouds). The set contains the 3-D accelerator PIC code WARP and the 2-D 'slice' e-cloud code POSINST [M. Furman, this workshop, paper TUAX05], as well as a merger of the two, augmented by new modules for impact ionization and neutral gas generation. The new capability runs on workstations or parallel supercomputers and contains advanced features such as mesh refinement, disparate adaptive time stepping, and a new 'drift-Lorentz' particle mover for tracking charged particles in magnetic fields using large time steps. It is being applied to the modeling of ion beams (1 MeV, 180 mA, K+) for heavy ion inertial fusion and warm dense matter studies, as they interact with electron clouds in the High-Current Experiment (HCX) [experimental results discussed by A. Molvik, this workshop, paper THAW02]. We describe the capabilities and present recent simulation results with detailed comparisons against the HCX experiment, as well as their application (in a different regime) to the modeling of e-clouds in the Large Hadron Collider (LHC). (author)

New simulation capabilities of electron clouds in ion beams with large tune depression

International Nuclear Information System (INIS)

Lawrence Livermore National Laboratory

2006-01-01

We have developed a new, comprehensive set of simulation tools aimed at modeling the interaction of intense ion beams and electron clouds (e-clouds). The set contains the 3-D accelerator PIC code WARP and the 2-D ''slice'' e-cloud code POSINST [M. Furman, this workshop, paper TUAX05], as well as a merger of the two, augmented by new modules for impact ionization and neutral gas generation. The new capability runs on workstations or parallel supercomputers and contains advanced features such as mesh refinement, disparate adaptive time stepping, and a new ''drift-Lorentz'' particle mover for tracking charged particles in magnetic fields using large time steps. It is being applied to the modeling of ion beams (1 MeV, 180 mA, K+) for heavy ion inertial fusion and warm dense matter studies, as they interact with electron clouds in the High-Current Experiment (HCX) [experimental results discussed by A. Molvik, this workshop, paper THAW02]. We describe the capabilities and present recent simulation results with detailed comparisons against the HCX experiment, as well as their application (in a different regime) to the modeling of e-clouds in the Large Hadron Collider (LHC)

An improved current control scheme for grid-connected DG unit based distribution system harmonic compensation

DEFF Research Database (Denmark)

He, Jinwei; Wei Li, Yun; Wang, Xiongfei

2013-01-01

In order to utilize DG unit interfacing converters to actively compensate distribution system harmonics, this paper proposes an enhanced current control approach. It seamlessly integrates system harmonic mitigation capabilities with the primary DG power generation function. As the proposed current...... controller has two well decoupled control branches to independently control fundamental and harmonic DG currents, phase-locked loops (PLL) and system harmonic component extractions can be avoided during system harmonic compensation. Moreover, a closed-loop power control scheme is also employed to derive...... the fundamental current reference. The proposed power control scheme effectively eliminates the impacts of steady-state fundamental current tracking errors in the DG units. Thus, an accurate power control is realized even when the harmonic compensation functions are activated. Experimental results from a single...

Current Capabilities and Development Potential in Surgical Robotics

Directory of Open Access Journals (Sweden)

Mathias Hoeckelmann

2015-05-01

Full Text Available Commercial surgical robots have been in clinical use since the mid-1990s, supporting surgeons in various tasks. In the past decades, many systems emerged as research platforms, and a few entered the global market. This paper summarizes the currently available surgical systems and research directions in the broader field of surgical robotics. The widely deployed teleoperated manipulators aim to enhance human cognitive and physical skills and provide smart tools for surgeons, while image-guided robotics focus on surpassing human limitations by introducing automated targeting and treatment delivery methods. Both concepts are discussed based on prototypes and commercial systems. Through concrete examples the possible future development paths of surgical robots are illustrated. While research efforts are taking different approaches to improve the capacity of such systems, the aim of this survey is to assess their maturity from the commercialization point of view.

New facility boost CSIRO's micromanfacturing capability

International Nuclear Information System (INIS)

Grad, Paul.

1997-01-01

CSIRO is developing a leading edge microengineering capability, an electron beam lithography and device fabrication facility. Structures of submicron size can be manufactured and incorporated in microelectronic or micromechanical devices. Current and potential uses are outlined in this paper and include: chemical sensors, electronic surveillance and radar systems, microsensors, micromotors and microgages to be used in telecommunication, environment monitoring or medicine

Blind spots of dynamic capabilities: A systems theoretic perspective

Directory of Open Access Journals (Sweden)

Robert Burisch

2016-05-01

Full Text Available Dynamic capabilities remain one of the most popular, but also one of the most controversial topics in current knowledge and innovation research. This study exposes strengths and weaknesses of existing conceptualizations of dynamic capabilities by using a systems theoretic lens. Systems theory suggests that organizations operate in environments they cannot fully understand. Thus, organizational action patterns inevitably involve simplification, selectivity and uncertainty leading to inherent blind spots in every kind of strategic action. As the resulting insight, fully flexible organizational capabilities might not be achievable and continuous adaptation to every kind of environmental change cannot be possible from a systems theoretic perspective. Accordingly, this work discusses empirical difficulties that derive from the preceding argumentation and outlines a corresponding re-conceptualization of the dynamic capabilities concept.

Current Needs for the Experimental Investigation of the CHF Phenomenon Relevant to LWR Core Conditions

International Nuclear Information System (INIS)

Le Corre, J.M.

2009-01-01

The current achievements and needs toward the investigation, understanding and mechanistic prediction of the Critical Heat Flux (CHF) event, under PWR and BWR core conditions, are addressed in this paper. It is shown that, even when using advanced 3-D CFD simulation tools, the current approach to CHF mechanistic modeling has serious limitations. This is mainly due to the lack of information regarding the relevant two-phase flow pattern(s) (in particular near the heated wall) and associated mechanisms (at the meso and micro-scale) leading to the CHF event. Areas of current experimental needs are identified in order to address these shortcomings. In addition, the use of 1-D and 3-D numerical tools to mechanistically predict the CHF is discussed. It is shown that 3-D two-phase CFD codes may not be superior to 1-D codes without proper consideration of relevant constitutive relations. (author)

Current Projects Strengthening Capabilities in Disused Sealed Radioactive Source (DSRS) Management

International Nuclear Information System (INIS)

Roughan, Cathleen Maura

2017-01-01

IAEA NEFW-WTS Operations - Overview: •Condition and store or remove DSRS Categories 1-5 •Provide tools and technology for management of DSRS •Assist in design of facilities for safe and secure handling and storage •Work with suppliers, recycles and service company providers to find suitable handling and transport options – limited options available •Coordinated missions with Safety, Security to address DSRS needs in the Member State – holistic approach •Build capacity and sustainability in Member States. Qualified Technical Centre: •Increase the worldwide capability to manage DSRS: –Encouraging countries with well-equipped centres or facilities and trained personnel to provide a range of technical services for the management of DSRS; –Within their countries and regionally; –Assist in implementing IAEA activities; •Build capacity and sustainability in MSs

Fatigue Crack Length Sizing Using a Novel Flexible Eddy Current Sensor Array

Directory of Open Access Journals (Sweden)

Ruifang Xie

2015-12-01

Full Text Available The eddy current probe, which is flexible, array typed, highly sensitive and capable of quantitative inspection is one practical requirement in nondestructive testing and also a research hotspot. A novel flexible planar eddy current sensor array for the inspection of microcrack presentation in critical parts of airplanes is developed in this paper. Both exciting and sensing coils are etched on polyimide films using a flexible printed circuit board technique, thus conforming the sensor to complex geometric structures. In order to serve the needs of condition-based maintenance (CBM, the proposed sensor array is comprised of 64 elements. Its spatial resolution is only 0.8 mm, and it is not only sensitive to shallow microcracks, but also capable of sizing the length of fatigue cracks. The details and advantages of our sensor design are introduced. The working principal and the crack responses are analyzed by finite element simulation, with which a crack length sizing algorithm is proposed. Experiments based on standard specimens are implemented to verify the validity of our simulation and the efficiency of the crack length sizing algorithm. Experimental results show that the sensor array is sensitive to microcracks, and is capable of crack length sizing with an accuracy within ±0.2 mm.

Control of the UV flux of a XeCl dielectric barrier discharge excilamp through its current variation

Energy Technology Data Exchange (ETDEWEB)

Piquet, H; Bhosle, S; Diez, R; Cousineau, M; Djibrillah, M; Le Thanh, D; Dagang, A N; Zissis, G

2012-02-28

The efficiency of the electrical power transfer to the gas mixture of a XeCl dielectric barrier discharge (DBD) exciplex lamp is analysed. An equivalent circuit model of the DBD is considered. It is shown that the excilamp power can be controlled by applying current to the lamp. This highly desired property is ensured by means of a specific power supply topology, whose concepts and design are discussed. The experimental prototype of a current-mode converter operating in the pulsed regime at pulse repetition rate of 50 kHz is presented and its capability to control the amount of energy transferred during each current pulse is demonstrated. The capability of this power supply to maintain specific operating conditions for the DBD lamp, with a very stable behaviour (even at a very low current, in the regime of a single discharge channel), is illustrated. The experimental results of a combined use of this converter and a XeCl excilamp are presented. The influence of the supply parameters on the 308-nm XeCl excilamp is analysed. The shape of the UV pulse of the lamp is experimentally shown to be similar to that of the current, which actually flows into the gas mixture. The UV radiation power is demonstrated to be tightly correlated to the current injected into the gas and controlled by the available degrees of freedom offered by the power supply. The measured UV output characteristics and performance of the system are discussed. Time resolved UV imaging of a XeCl DBD excilamp is used to analyse the mechanisms involved in the production of exciplexes at various power supply regimes. It is shown that a pulsed voltage source leads to formation of short high intensity UV peaks, while current pulses lead to formation of sustained discharge filaments. Based on the results of modelling of the above-mentioned operation conditions, the two power supply regimes are compared and analysed from the point of view of the UV power and radiative control.

High-current relativistic klystron amplifier development for microsecond pulse lengths

International Nuclear Information System (INIS)

Fazio, M.V.; Carlsten, B.E.; Faehl, R.; Kwan, T.J.; Rickel, D.G.; Stringfield, R.M.; Tallerico, P.J.

1991-01-01

Los Alamos is extending the performance of the Friedman-type, high-current relativistic klystron amplifier (RKA) to the microsecond regime while attempting to achieve the gigawatt-level peak power capability that has been characteristic of the RKA at shorter pulse lengths. Currently the electron beam power into the device is about 1 GW in microsecond duration pulses, with an effort underway to increase the beam power to 2.5 GW. To data the device has yielded an rf modulated electron beam power of 350 MW, with up to 50 MW coupled into waveguide. Several aspects of RKA operation under investigation that affect RKA beam bunching efficiency and amplifier gain include cavity tuning, beam diameter, beam current, and input rf drive power, and the development of an output coupler that efficiently couples the microwave power from the low impedance beam into rectangular waveguide operating in the dominant mode. Current results from experimental testing and code modeling are presented

High-current relativistic klystron amplifier development for microsecond pulse lengths

International Nuclear Information System (INIS)

Fazio, M.V.; Carlsten, B.E.; Faehl, R.J.; Kwan, T.J.; Rickel, D.G.; Stringfield, R.M.; Tallerico, P.J.

1991-01-01

Los Alamos is extending the performance of the Friedman-type, high-current relativistic klystron amplifier (RKA) to the microsecond regime while attempting to achieve the gigawatt-level peak power capability that has been characteristic of the RKA at shorter pulse lengths. Currently the electron beam power into the device is about 1 GW in microsecond duration pulses, with an effort underway to increase the beam power to 2.5 GW. To date the device has yielded an rf modulated electron beam power of 350 MW, with up to 50 MW coupled into waveguide. Several aspects of RKA operation under investigation that affect RKA beam bunching efficiency and amplifier gain include cavity tuning, beam diameter, beam current, and input rf drive power, and the development of an output coupler that efficiently couples the microwave power from the low impedance beam into rectangular waveguide operating in the dominant mode. Current results from experimental testing and code modelling are presented. 5 refs., 5 figs

Dynamic capabilities, Marketing Capability and Organizational Performance

Directory of Open Access Journals (Sweden)

Adriana Roseli Wünsch Takahashi

2017-01-01

Full Text Available The goal of the study is to investigate the influence of dynamic capabilities on organizational performance and the role of marketing capabilities as a mediator in this relationship in the context of private HEIs in Brazil. As a research method we carried out a survey with 316 IES and data analysis was operationalized with the technique of structural equation modeling. The results indicate that the dynamic capabilities have influence on organizational performance only when mediated by marketing ability. The marketing capability has an important role in the survival, growth and renewal on educational services offerings for HEIs in private sector, and consequently in organizational performance. It is also demonstrated that mediated relationship is more intense for HEI with up to 3,000 students and other organizational profile variables such as amount of courses, the constitution, the type of institution and type of education do not significantly alter the results.

Design Mechanism as Territorial Strategic Capability

Directory of Open Access Journals (Sweden)

Gianita BLEOJU

2009-01-01

Full Text Available The current exigencies that a territory must faced in order to its’ optimalpositioning in future regional competition requires the ability to design theappropriate mechanism which better valorize the territory capability. Such aconstruct is vital for territorial sustainable development and supposes thecreation of a specific body of knowledge from distinctive local resourceexploitation and unique value creation and allocation. Territorial mechanismdesign is a typical management decision about identification, ownership andcontrol of specific strategic capabilities and their combination in a distinctiveterritorial portfolio. The most difficult responsibility is to allocate the territorialvalue added which is a source of conflict among territorial components. Ourcurrent paper research covers the basics of two complementary territorialpillars-rural and tourism potential and proves the lack of specific designmechanisms which explain the current diminishing value of Galati Brailaregion. The proposed management system, relying upon territorial controlmechanism, will ensure knowledge sharing process via collaborative learning,with the final role of appropriate territorial attractivity signals, reinforcingidentity as key factor of territorial attractability. Our paper is fully documentedon there years of data analyzing from territorial area of interest. This offers usthe necessary empiric contrasting for our proposed solution.

Automatic Condition Monitoring of Industrial Rolling-Element Bearings Using Motor’s Vibration and Current Analysis

DEFF Research Database (Denmark)

Yang, Zhenyu

2015-01-01

An automatic condition monitoring for a class of industrial rolling-element bearings is developed based on the vibration as well as stator current analysis. The considered fault scenarios include a single-point defect, multiple-point defects, and a type of distributed defect. Motivated by the pot...... characteristic frequencies, sideband effects, time-average of spectra, and selection of fault index and thresholds, are also discussed. The experimental work shows a huge potential to use some simple methods for successful diagnosis of industrial bearing systems.......An automatic condition monitoring for a class of industrial rolling-element bearings is developed based on the vibration as well as stator current analysis. The considered fault scenarios include a single-point defect, multiple-point defects, and a type of distributed defect. Motivated...... is extensively studied under diverse operating conditions: different sensor locations, motor speeds, loading conditions, and data samples from different time segments. The experimental results showed the powerful capability of vibration analysis in the bearing point defect fault diagnosis. The current analysis...

Aircraft Capability Management

Science.gov (United States)

Mumaw, Randy; Feary, Mike

2018-01-01

This presentation presents an overview of work performed at NASA Ames Research Center in 2017. The work concerns the analysis of current aircraft system management displays, and the initial development of an interface for providing information about aircraft system status. The new interface proposes a shift away from current aircraft system alerting interfaces that report the status of physical components, and towards displaying the implications of degradations on mission capability. The proposed interface describes these component failures in terms of operational consequences of aircraft system degradations. The research activity was an effort to examine the utility of different representations of complex systems and operating environments to support real-time decision making of off-nominal situations. A specific focus was to develop representations that provide better integrated information to allow pilots to more easily reason about the operational consequences of the off-nominal situations. The work is also seen as a pathway to autonomy, as information is integrated and understood in a form that automated responses could be developed for the off-nominal situations in the future.

Sandia Laboratories technical capabilities. Auxiliary capabilities: environmental health information science

International Nuclear Information System (INIS)

1975-09-01

Sandia Laboratories is an engineering laboratory in which research, development, testing, and evaluation capabilities are integrated by program management for the generation of advanced designs. In fulfilling its primary responsibility to ERDA, Sandia Laboratories has acquired extensive research and development capabilities. The purpose of this series of documents is to catalog the many technical capabilities of the Laboratories. After the listing of capabilities, supporting information is provided in the form of highlights, which show applications. This document deals with auxiliary capabilities, in particular, environmental health and information science. (11 figures, 1 table) (RWR)

Study on decay heat removal capability of reactor vessel auxiliary cooling system

International Nuclear Information System (INIS)

Nishi, Y.; Kinoshita, I.

1991-01-01

The reactor vessel auxiliary cooling system (RVACS) is a simple, Passive decay heat removal system for an LMFBR. However, the heat removal capacity of this system is small compared to that of an immersed type of decay heat exchanger. In this study, a high-porosity porous body is proposed to enhance the RVACS's heat transfer performance to improve its applicability. The objectives of this study are to propose a new method which is able to use thermal radiation effectively, to confirm its heat removal capability and to estimate its applicability limit of RVACS for an LMFBR. Heat transfer tests were conducted in an experimental facility with a 3.5 m heat transfer height to evaluate the heat transfer performance of the high-porosity porous body. Using the experimental results, plant transient analyses were performed for a 300 MWe pool type LMFBR under a Total Black Out (TBO) condition to confirm the heat removal capability. Furthermore, the relationship between heat removal capability and thermal output of a reactor were evaluated using a simple parameter model

Leveraging Innovation Capabilities of Asian Micro, Small and ...

International Development Research Centre (IDRC) Digital Library (Canada)

Leveraging Innovation Capabilities of Asian Micro, Small and Medium Enterprises through Intermediary Organizations. Micro, small and medium enterprises (MSMEs) are a source of livelihood for billions of poor people worldwide. The current global economic downturn has hit these enterprises particularly hard, putting ...

Influence of Cultural, Organizational, and Automation Capability on Human Automation Trust: A Case Study of Auto-GCAS Experimental Test Pilots

Science.gov (United States)

Koltai, Kolina; Ho, Nhut; Masequesmay, Gina; Niedober, David; Skoog, Mark; Cacanindin, Artemio; Johnson, Walter; Lyons, Joseph

2014-01-01

This paper discusses a case study that examined the influence of cultural, organizational and automation capability upon human trust in, and reliance on, automation. In particular, this paper focuses on the design and application of an extended case study methodology, and on the foundational lessons revealed by it. Experimental test pilots involved in the research and development of the US Air Force's newly developed Automatic Ground Collision Avoidance System served as the context for this examination. An eclectic, multi-pronged approach was designed to conduct this case study, and proved effective in addressing the challenges associated with the case's politically sensitive and military environment. Key results indicate that the system design was in alignment with pilot culture and organizational mission, indicating the potential for appropriate trust development in operational pilots. These include the low-vulnerability/ high risk nature of the pilot profession, automation transparency and suspicion, system reputation, and the setup of and communications among organizations involved in the system development.

Automatic Condition Monitoring of Industrial Rolling-Element Bearings Using Motor’s Vibration and Current Analysis

Directory of Open Access Journals (Sweden)

Zhenyu Yang

2015-01-01

Full Text Available An automatic condition monitoring for a class of industrial rolling-element bearings is developed based on the vibration as well as stator current analysis. The considered fault scenarios include a single-point defect, multiple-point defects, and a type of distributed defect. Motivated by the potential commercialization, the developed system is promoted mainly using off-the-shelf techniques, that is, the high-frequency resonance technique with envelope detection and the average of short-time Fourier transform. In order to test the flexibility and robustness, the monitoring performance is extensively studied under diverse operating conditions: different sensor locations, motor speeds, loading conditions, and data samples from different time segments. The experimental results showed the powerful capability of vibration analysis in the bearing point defect fault diagnosis. The current analysis also showed a moderate capability in diagnosis of point defect faults depending on the type of fault, severity of the fault, and the operational condition. The temporal feature indicated a feasibility to detect generalized roughness fault. The practical issues, such as deviations of predicted characteristic frequencies, sideband effects, time-average of spectra, and selection of fault index and thresholds, are also discussed. The experimental work shows a huge potential to use some simple methods for successful diagnosis of industrial bearing systems.

Diagnosing the uncertainty and detectability of emission reductions for REDD + under current capabilities: an example for Panama

International Nuclear Information System (INIS)

Pelletier, Johanne; Potvin, Catherine; Ramankutty, Navin

2011-01-01

In preparation for the deployment of a new mechanism that could address as much as one fifth of global greenhouse gas emissions by reducing emissions from deforestation and forest degradation (REDD +), important work on methodological issues is still needed to secure the capacity to produce measurable, reportable, and verifiable emissions reductions from REDD + in developing countries. To contribute to this effort, we have diagnosed the main sources of uncertainty in the quantification of emission from deforestation for Panama, one of the first countries to be supported by the Forest Carbon Partnership Facility of the World Bank and by UN-REDD. Performing sensitivity analyses using a land-cover change emissions model, we identified forest carbon stocks and the quality of land-cover maps as the key parameters influencing model uncertainty. The time interval between two land-cover assessments, carbon density in fallow and secondary forest, and the accuracy of land-cover classifications also affect our ability to produce accurate estimates. Further, we used the model to compare emission reductions from five different deforestation reduction scenarios drawn from governmental input. Only the scenario simulating a reduction in deforestation by half succeeds in crossing outside the confidence bounds surrounding the baseline emission obtained from the uncertainty analysis. These results suggest that with current data, real emission reductions in developing countries could be obscured by their associated uncertainties. Ways of addressing the key sources of error are proposed, for developing countries involved in REDD + , for improving the accuracy of their estimates in the future. These new considerations confirm the importance of current efforts to establish forest monitoring systems and enhance capabilities for REDD + in developing countries.

Dominant factors governing the rate capability of a TiO2 nanotube anode for high power lithium ion batteries.

Science.gov (United States)

Han, Hyungkyu; Song, Taeseup; Lee, Eung-Kwan; Devadoss, Anitha; Jeon, Yeryung; Ha, Jaehwan; Chung, Yong-Chae; Choi, Young-Min; Jung, Yeon-Gil; Paik, Ungyu

2012-09-25

Titanium dioxide (TiO(2)) is one of the most promising anode materials for lithium ion batteries due to low cost and structural stability during Li insertion/extraction. However, its poor rate capability limits its practical use. Although various approaches have been explored to overcome this problem, previous reports have mainly focused on the enhancement of both the electronic conductivity and the kinetic associated with lithium in the composite film of active material/conducting agent/binder. Here, we systematically explore the effect of the contact resistance between a current collector and a composite film of active material/conducting agent/binder on the rate capability of a TiO(2)-based electrode. The vertically aligned TiO(2) nanotubes arrays, directly grown on the current collector, with sealed cap and unsealed cap, and conventional randomly oriented TiO(2) nanotubes electrodes were prepared for this study. The vertically aligned TiO(2) nanotubes array electrode with unsealed cap showed superior performance with six times higher capacity at 10 C rate compared to conventional randomly oriented TiO(2) nanotubes electrode with 10 wt % conducting agent. On the basis of the detailed experimental results and associated theoretical analysis, we demonstrate that the reduction of the contact resistance between electrode and current collector plays an important role in improving the electronic conductivity of the overall electrode system.

Current Capabilities at SNL for the Integration of Small Modular Reactors onto Smart Microgrids Using Sandia's Smart Microgrid Technology High Performance Computing and Advanced Manufacturing.

Energy Technology Data Exchange (ETDEWEB)

Rodriguez, Salvador B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

Smart grids are a crucial component for enabling the nation’s future energy needs, as part of a modernization effort led by the Department of Energy. Smart grids and smart microgrids are being considered in niche applications, and as part of a comprehensive energy strategy to help manage the nation’s growing energy demands, for critical infrastructures, military installations, small rural communities, and large populations with limited water supplies. As part of a far-reaching strategic initiative, Sandia National Laboratories (SNL) presents herein a unique, three-pronged approach to integrate small modular reactors (SMRs) into microgrids, with the goal of providing economically-competitive, reliable, and secure energy to meet the nation’s needs. SNL’s triad methodology involves an innovative blend of smart microgrid technology, high performance computing (HPC), and advanced manufacturing (AM). In this report, Sandia’s current capabilities in those areas are summarized, as well as paths forward that will enable DOE to achieve its energy goals. In the area of smart grid/microgrid technology, Sandia’s current computational capabilities can model the entire grid, including temporal aspects and cyber security issues. Our tools include system development, integration, testing and evaluation, monitoring, and sustainment.

Capability demonstration of simultaneous proton beam irradiation during exposure to molten lead–bismuth eutectic for HT9 steel

International Nuclear Information System (INIS)

Qvist, Staffan; Bolind, Alan Michael; Hosemann, Peter; Wang, Yongqiang; Tesmer, Joseph; De Caro, Magdalena Serrano; Bourke, Mark

2013-01-01

We report the design and assembly of a corrosion station to enable simultaneous proton irradiation of a metallic surface that was also in contact with molten lead–bismuth eutectic (LBE). The capability has been established at the ion beam materials laboratory at Los Alamos National Laboratory (LANL). The engineering design focused on temperature and oxygen content control in the LBE, as well as the ability to achieve doses significantly in excess of 1 dpa in the contact region over the irradiation campaigns. In the preliminary demonstration of capability reported here, a sample made of HT9 steel was placed in contact with LBE at 450 °C and irradiated for 58 h at an average proton beam current of 0.3 μA/mm 2 . SRIM [1] calculations indicate that the nominal surface dose ranged from approximately 3–22 dpa. This paper outlines the experimental setup and design constraints. Characterization of the sample will be reported in a subsequent paper.

Capability demonstration of simultaneous proton beam irradiation during exposure to molten lead–bismuth eutectic for HT9 steel

Energy Technology Data Exchange (ETDEWEB)

Qvist, Staffan, E-mail: staffan@berkeley.edu [University of California, Berkeley (United States); Bolind, Alan Michael [University of California, Berkeley (United States); Japan Atomic Energy Agency (Japan); Hosemann, Peter [University of California, Berkeley (United States); Wang, Yongqiang; Tesmer, Joseph; De Caro, Magdalena Serrano; Bourke, Mark [Los Alamos National Laboratory (United States)

2013-01-11

We report the design and assembly of a corrosion station to enable simultaneous proton irradiation of a metallic surface that was also in contact with molten lead–bismuth eutectic (LBE). The capability has been established at the ion beam materials laboratory at Los Alamos National Laboratory (LANL). The engineering design focused on temperature and oxygen content control in the LBE, as well as the ability to achieve doses significantly in excess of 1 dpa in the contact region over the irradiation campaigns. In the preliminary demonstration of capability reported here, a sample made of HT9 steel was placed in contact with LBE at 450 °C and irradiated for 58 h at an average proton beam current of 0.3 μA/mm{sup 2}. SRIM [1] calculations indicate that the nominal surface dose ranged from approximately 3–22 dpa. This paper outlines the experimental setup and design constraints. Characterization of the sample will be reported in a subsequent paper.

Experimental facility of innovative types as the laboratory analog of research reactor experimental device

International Nuclear Information System (INIS)

Androsenko, A.A.; Androsenko, P.A.; Zabud'ko, A.N.; Kremenetskij, A.K.; Nikolaev, A.N.; Trykov, L.A.

1991-01-01

The paper analyses capability of creating laboratory analogs of complex experimental facilities at research reactors utilizing power radionuclide neutron sources fabricated in industrial conditions. Some experimental and calculational investigations of neutron-physical characteristics are presented, which have been attained at the RIZ research reactor laboratory analog. Experimental results are supplemented by calculational investigations, fulfilled by means of the BRAND three-dimensional computational complex and the ROZ-6 one-dimensional program. 4 refs.; 3 figs

Eddy current array probe for detection of surface breaking cracks in the extrados of feeder bends

International Nuclear Information System (INIS)

Obrutsky, L.S.; Cassidy, R.A.; Chaplin, K.; Martin, P.; Bureau, J.F.

2006-01-01

A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to inspect first and second bends with similar settings and capabilities; permanent record for future reference; axial and circumferential crack detection in a single scan; capability to detect OD surface-breaking cracks, which can provide additional information to that provided by ultrasonic testing (UT) for flaw characterization, and detection threshold: Surface breaking cracks equivalent to a 0.5 mm deep, 10 mm long EDM notch located on the OD of the bend extrados. This paper discusses the basis for probe design, summarizes the experimental work to evaluate probe capabilities and analyzes the results from the field trial. (author)

Eddy current array probe for detection of surface breaking cracks in the extrados of feeder bends

Energy Technology Data Exchange (ETDEWEB)

Obrutsky, L.S.; Cassidy, R.A.; Chaplin, K. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada)]. E-mail: obrutskyl@aecl.ca; Martin, P. [NB Power, Point Lepreau NGS, Point Lepreau, New Brunswick (Canada)]. E-mail: PMartin@nbpower.com; Bureau, J.F. [Zetec, Quebec, Quebec (Canada)]. E-mail: jean-francois.bureau@zetec.com

2006-07-01

A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to inspect first and second bends with similar settings and capabilities; permanent record for future reference; axial and circumferential crack detection in a single scan; capability to detect OD surface-breaking cracks, which can provide additional information to that provided by ultrasonic testing (UT) for flaw characterization, and detection threshold: Surface breaking cracks equivalent to a 0.5 mm deep, 10 mm long EDM notch located on the OD of the bend extrados. This paper discusses the basis for probe design, summarizes the experimental work to evaluate probe capabilities and analyzes the results from the field trial. (author)

Inference of ICF Implosion Core Mix using Experimental Data and Theoretical Mix Modeling

International Nuclear Information System (INIS)

Welser-Sherrill, L.; Haynes, D.A.; Mancini, R.C.; Cooley, J.H.; Tommasini, R.; Golovkin, I.E.; Sherrill, M.E.; Haan, S.W.

2009-01-01

The mixing between fuel and shell materials in Inertial Confinement Fusion (ICF) implosion cores is a current topic of interest. The goal of this work was to design direct-drive ICF experiments which have varying levels of mix, and subsequently to extract information on mixing directly from the experimental data using spectroscopic techniques. The experimental design was accomplished using hydrodynamic simulations in conjunction with Haan's saturation model, which was used to predict the mix levels of candidate experimental configurations. These theoretical predictions were then compared to the mixing information which was extracted from the experimental data, and it was found that Haan's mix model performed well in predicting trends in the width of the mix layer. With these results, we have contributed to an assessment of the range of validity and predictive capability of the Haan saturation model, as well as increased our confidence in the methods used to extract mixing information from experimental data.

Automated ultrasonic testing--capabilities, limitations and methods

International Nuclear Information System (INIS)

Beller, L.S.; Mikesell, C.R.

1977-01-01

The requirements for precision and reproducibility of ultrasonic testing during inservice inspection of nuclear reactors are both quantitatively and qualitatively more severe than most current practice in the field can provide. An automated ultrasonic testing (AUT) system, which provides a significant advancement in field examination capabilities, is described. Properties of the system, its application, and typical results are discussed

Nuclear Research and Development Capabilities Needed to Support Future Growth

Energy Technology Data Exchange (ETDEWEB)

Wham, Robert M. [ORNL, P.O. Box 2008, Oak Ridge, TN 37831-6154 (United States); Kearns, Paul [Battelle Memorial Institute (United States); Marston, Ted [Marston Consulting (United States)

2009-06-15

The energy crisis looming before the United States can be resolved only by an approach that integrates a 'portfolio' of options. Nuclear energy, already an important element in the portfolio, should play an even more significant role in the future as the U.S. strives to attain energy independence and reduce carbon emissions. The DOE Office of Nuclear Energy asked Battelle Memorial Institute to obtain input from the commercial power generation industry on industry's vision for nuclear energy over the next 30-50 years. With this input, Battelle was asked to generate a set of research and development capabilities necessary for DOE to support the anticipated growth in nuclear power generation. This presentation, based on the report generated for the Office of Nuclear Energy, identifies the current and future nuclear research and development capabilities required to make this happen. The capabilities support: (1) continued, safe operation of the current fleet of nuclear plants; (2) the availability of a well qualified and trained workforce; (3) demonstration of the next generation nuclear plants; (4) development of a sustainable fuel cycle; (5) advanced technologies for maximizing resource utilization and minimization of waste and (6) advanced modeling and simulation for rapid and reliable development and deployment of new nuclear technologies. In order to assure these capabilities are made available, a Strategic Nuclear Energy Capability Initiative is proposed to provide the required resources during this critical period of time. (authors)

Plasma auxiliary heating and current drive

International Nuclear Information System (INIS)

1999-01-01

Heating and current drive systems must fulfil several roles in ITER operating scenarios: heating through the H-mode transition and to ignition; plasma burn control; current drive and current profile control in steady state scenarios; and control of MHD instabilities. They must also perform ancillary functions, such as assisting plasma start-up and wall conditioning. It is recognized that no one system can satisfy all of these requirements with the degree of flexibility that ITER will require. Four heating and current drive systems are therefore under consideration for ITER: electron cyclotron waves at a principal frequency of 170 GHz; fast waves operating in the range 40-70 MHz (ion cyclotron waves); lower hybrid waves at 5 GHz; and neutral beam injection using negative ion beam technology for operation at 1 MeV energy. It is likely that several of these systems will be employed in parallel. The systems have been chosen on the basis of the maturity of physics understanding and operating experience in current experiments and on the feasibility of applying the relevant technology to ITER. Here, the fundamental physics describing the interaction of these heating systems with the plasma is reviewed, the relevant experimental results in the exploitation of the heating and current drive capabilities of each system are discussed, key aspects of their application to ITER are outlined, and the major technological developments required in each area are summarized. (author)

Experimental and analytical study on vibration control effects of eddy-current tuned mass dampers under seismic excitations

Science.gov (United States)

Lu, Zheng; Huang, Biao; Zhang, Qi; Lu, Xilin

2018-05-01

Eddy-current tuned mass dampers (EC-TMDs) are non-contacting passive control devices and are developed on the basis of conventional tuned mass dampers. They comprise a solid mass, a stiffness element, and a damping element, wherein the damping mechanism originates from eddy currents. By relative motion between a non-magnetic conductive metal and a permanent magnet in a dynamic system, a time-varying magnetic field is induced in the conductor, thereby generating eddy currents. The eddy currents induce a magnetic field with opposite polarity, causing repulsive forces, i.e., damping forces. This technology can overcome the drawbacks of conventional tuned mass dampers, such as limited service life, deterioration of mechanical properties, and undesired additional stiffness. The experimental and analytical study of this system installed on a multi-degree-of-freedom structure is presented in this paper. A series of shaking table tests were conducted on a five-story steel-frame model with/without an EC-TMD to evaluate the effectiveness and performance of the EC-TMD in suppressing the vibration of the model under seismic excitations. The experimental results show that the EC-TMD can effectively reduce the displacement response, acceleration response, interstory drift ratio, and maximum strain of the columns under different earthquake excitations. Moreover, an analytical method was proposed on the basis of electromagnetic and structural dynamic theories. A comparison between the test and simulation results shows that the simulation method can be used to estimate the response of structures with an EC-TMD under earthquake excitations with acceptable accuracy.

Development of an environmental radiation analysis research capability in the UAE

International Nuclear Information System (INIS)

Kim, Sung-yeop; Kim, Chankyu; Lee, Kun Jai; Chang, Soon Heung; Elmasri, Hasna; Beeley, Philip A.

2013-01-01

The UAE has started a nuclear energy program with the aim of having its first four units on-line between 2017 and 2020 and it is important that the country has an environmental radiation analysis capability to support this program. Khalifa University is therefore implementing a research laboratory to support both experimental analysis and radionuclide transport modeling in the aquatic and terrestrial environment. This paper outlines the development of this capability as well as the work in progress and planned for the future. - Highlights: • New university environmental radiation laboratory established in UAE. • Facilities included for alpha, beta and gamma radiometrics. • Transport modeling capability is being established. • Laboratory also used for education and training. • Robotic methods for sampling and analysis are under development

Managing Capabilities for Supply Chain Resilience Through it Integration

Directory of Open Access Journals (Sweden)

Gružauskas Valentas

2017-08-01

Full Text Available The trend for e-commerce, estimated population size to 11 billion by 2050, and an increase in urbanization level to 70 % is requiring to re-think the current supply chain. These trends changed the distribution process: delivery distances are decreasing, the product variety is increasing, and more products are being sold in smaller quantities. Therefore, the concept of supply chain resilience has gained more recognition in recent years. The scientific literature analysis conducted by the authors indicate several capabilities that influence supply chain resilience. Collaboration, flexibility, redundancy and integration are the most influential capabilities to supply chain resilience. However, the authors identify that the combination of these capabilities to supply chain resilience is under researched. The authors indicate that by combining these capabilities with the upcoming technologies of industry 4.0, supply chain resilience can be achieved. In the future, the authors are planning to conduct further research to identify the influence of these capabilities to supply chain resilience, to quantify supply chain resilience, and to provide further practices of industry 4.0 concept usage for supply chain resilience.

Current Capabilities, Requirements and a Proposed Strategy for Interdependency Analysis in the UK

Science.gov (United States)

Bloomfield, Robin; Chozos, Nick; Salako, Kizito

The UK government recently commissioned a research study to identify the state-of-the-art in Critical Infrastructure modelling and analysis, and the government/industry requirements for such tools and services. This study (Cetifs) concluded with a strategy aiming to bridge the gaps between the capabilities and requirements, which would establish interdependency analysis as a commercially viable service in the near future. This paper presents the findings of this study that was carried out by CSR, City University London, Adelard LLP, a safety/security consultancy and Cranfield University, defense academy of the UK.

The Advanced Test Reactor Irradiation Facilities and Capabilities

International Nuclear Information System (INIS)

S. Blaine Grover; Raymond V. Furstenau

2007-01-01

The Advanced Test Reactor (ATR) is one of the world's premiere test reactors for performing long term, high flux, and/or large volume irradiation test programs. The ATR is a very versatile facility with a wide variety of experimental test capabilities for providing the environment needed in an irradiation experiment. These different capabilities include passive sealed capsule experiments, instrumented and/or temperature-controlled experiments, and pressurized water loop experiment facilities. The ATR has enhanced capabilities in experiment monitoring and control systems for instrumented and/or temperature controlled experiments. The control systems utilize feedback from thermocouples in the experiment to provide a custom blended flowing inert gas mixture to control the temperature in the experiments. Monitoring systems have also been utilized on the exhaust gas lines from the experiment to monitor different parameters, such as fission gases for fuel experiments, during irradiation. ATR's unique control system provides axial flux profiles in the experiments, unperturbed by axially positioned control components, throughout each reactor operating cycle and over the duration of test programs requiring many years of irradiation. The ATR irradiation positions vary in diameter from 1.6 cm (0.625 inches) to 12.7 cm (5.0 inches) over an active core length of 122 cm (48.0 inches). Thermal and fast neutron fluxes can be adjusted radially across the core depending on the needs of individual test programs. This paper will discuss the different irradiation capabilities available and the cost/benefit issues related to each capability. Examples of different experiments will also be discussed to demonstrate the use of the capabilities and facilities at ATR for performing irradiation experiments

Bubble Radiation Detection: Current and Future Capability

International Nuclear Information System (INIS)

Peurrung, A.J.; Craig, R.A.

1999-01-01

Despite a number of noteworthy achievements in other fields, superheated droplet detectors (SDDs) and bubble chambers (BCs) have not been used for nuclear nonproliferation and arms control. This report examines these two radiation-detection technologies in detail and answers the question of how they can be or should be ''adapted'' for use in national security applications. These technologies involve closely related approaches to radiation detection in which an energetic charged particle deposits sufficient energy to initiate the process of bubble nucleation in a superheated fluid. These detectors offer complete gamma-ray insensitivity when used to detect neutrons. They also provide controllable neutron-energy thresholds and excellent position resolution. SDDs are extraordinarily simple and inexpensive. BCs offer the promise of very high efficiency (∼75%). A notable drawback for both technologies is temperature sensitivity. As a result of this problem, the temperature must be controlled whenever high accuracy is required, or harsh environmental conditions are encountered. The primary findings of this work are listed and briefly summarized below: (1) SDDs are ready to function as electronics-free neutron detectors on demand for arms-control applications. The elimination of electronics at the weapon's location greatly eases the negotiability of radiation-detection technologies in general. (2) As a result of their high efficiency and sharp energy threshold, current BCs are almost ready for use in the development of a next-generation active assay system. Development of an instrument based on appropriately safe materials is warranted. (3) Both kinds of bubble detectors are ready for use whenever very high gamma-ray fields must be confronted. Spent fuel MPC and A is a good example where this need presents itself. (4) Both kinds of bubble detectors have the potential to function as low-cost replacements for conventional neutron detectors such as 3 He tubes. For SDDs

Dynamic capabilities and innovation capabilities: The case of the ‘Innovation Clinic’

Directory of Open Access Journals (Sweden)

Fred Strønen

2017-01-01

Full Text Available In this explorative study, we investigate the relationship between dynamic capabilities and innovation capabilities. Dynamic capabilities are at the core of strategic management in terms of how firms can ensure adaptation to changing environments over time. Our paper follows two paths of argumentation. First, we review and discuss some major contributions to the theories on ordinary capabilities, dynamic capabilities, and innovation capabilities. We seek to identify different understandings of the concepts in question, in order to clarify the distinctions and relationships between dynamic capabilities and innovation capabilities. Second, we present a case study of the ’Innovation Clinic’ at a major university hospital, including four innovation projects. We use this case study to explore and discuss how dynamic capabilities can be extended, as well as to what extent innovation capabilities can be said to be dynamic. In our conclusion, we discuss the conditions for nurturing ‘dynamic innovation capabilities’ in organizations.

Transportation capabilities study of DOE-owned spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Clark, G.L.; Johnson, R.A.; Smith, R.W. [Packaging Technology, Inc., Tacoma, WA (United States); Abbott, D.G.; Tyacke, M.J. [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States)

1994-10-01

This study evaluates current capabilities for transporting spent nuclear fuel owned by the US Department of Energy. Currently licensed irradiated fuel shipping packages that have the potential for shipping the spent nuclear fuel are identified and then matched against the various spent nuclear fuel types. Also included are the results of a limited investigation into other certified packages and new packages currently under development. This study is intended to support top-level planning for the disposition of the Department of Energy`s spent nuclear fuel inventory.

Capability ethics

OpenAIRE

Robeyns, Ingrid

2012-01-01

textabstractThe capability approach is one of the most recent additions to the landscape of normative theories in ethics and political philosophy. Yet in its present stage of development, the capability approach is not a full-blown normative theory, in contrast to utilitarianism, deontological theories, virtue ethics, or pragmatism. As I will argue in this chapter, at present the core of the capability approach is an account of value, which together with some other (more minor) normative comm...

Nuclear Data Needs and Capabilities for Applications

Energy Technology Data Exchange (ETDEWEB)

Brown, D. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2015-05-27

In July 2014, DOE NP carried out a review of the US Nuclear Data Program. This led to several recommendations, including that the USNDP should “devise effective and transparent mechanisms to solicit input and feedback from all stakeholders on nuclear data needs and priorities.” The review also recommended that USNDP pursue experimental activities of relevance to nuclear data; the revised 2014 Mission Statement accordingly states that the USNDP uses “targeted experimental studies” to address gaps in nuclear data. In support of these recommendations, DOE NP requested that USNDP personnel organize a Workshop on Nuclear Data Needs and Capabilities for Applications (NDNCA). This Workshop was held at Lawrence Berkeley National Laboratory (LBNL) on 27-29 May 2015. The goal of the NDNCA Workshop was to compile nuclear data needs across a wide spectrum of applied nuclear science, and to provide a summary of associated capabilities (accelerators, reactors, spectrometers, etc.) available for the required measurements. The first two days of the workshop consisted of 25 plenary talks by speakers from 16 different institutions, on nuclear energy (NE), national security (NS), isotope production (IP), and industrial applications (IA). There were also shorter “capabilities” talks that described the experimental facilities and instrumentation available for the measurement of nuclear data. This was followed by a third day of topic-specific “breakout” sessions and a final closeout session. The agenda and copies of these talks are available online at http://bang.berkeley.edu/events/NDNCA/agenda. The importance of nuclear data to both basic and applied nuclear science was reflected in the fact that while the impetus for the workshop arose from the 2014 USNDP review, joint sponsorship for the workshop was provided by the Nuclear Science and Security Consortium, a UC-Berkeley based organization funded by the National Nuclear Security Administration (NNSA).

Experimental investigation of localized stress-induced leakage current distribution in gate dielectrics using array test circuit

Science.gov (United States)

Park, Hyeonwoo; Teramoto, Akinobu; Kuroda, Rihito; Suwa, Tomoyuki; Sugawa, Shigetoshi

2018-04-01

Localized stress-induced leakage current (SILC) has become a major problem in the reliability of flash memories. To reduce it, clarifying the SILC mechanism is important, and statistical measurement and analysis have to be carried out. In this study, we applied an array test circuit that can measure the SILC distribution of more than 80,000 nMOSFETs with various gate areas at a high speed (within 80 s) and a high accuracy (on the 10-17 A current order). The results clarified that the distributions of localized SILC in different gate areas follow a universal distribution assuming the same SILC defect density distribution per unit area, and the current of localized SILC defects does not scale down with the gate area. Moreover, the distribution of SILC defect density and its dependence on the oxide field for measurement (E OX-Measure) were experimentally determined for fabricated devices.

Experimental measurements of the eddy current signal due to a flawed, conducting half space

International Nuclear Information System (INIS)

Long, S.A.; Toomsawasdi, S.; Zaman, A.J.M.

1984-01-01

This chapter reports on an experimental investigation in which the change in impedance of a practical multi-turn eddy current coil near a conducting half space is measured as a function of the conductivity and the lift-off distance. The results are compared in a qualitative fashion with the analytical results for a single-turn coil. Measurements are also made of the change in impedance due to a small void in the conducting half space as a function of both its depth and radial position. The results indicate that, at least in a qualitative fashion, the precisely derived analytical solutions adequately predict the general behavior of the change in complex impedance of an eddy current coil above a conducting ground plane as a function of lift-off distance. It is determined that the effect of a sub-surface void on the change in inductance of the test coil correlates well with theoretical calculations

Reframing Inclusive Education: Educational Equality as Capability Equality

Science.gov (United States)

Terzi, Lorella

2014-01-01

In this paper, I argue that rethinking questions of inclusive education in the light of the value of educational equality--specifically conceived as capability equality, or genuine opportunities to achieve educational functionings--adds some important insights to the current debate on inclusive education. First, it provides a cohesive value…

Exploration Medical Capability - Technology Watch

Science.gov (United States)

Krihak, Michael; Watkins, Sharmila; Barr, Yael; Barsten, Kristina; Fung, Paul; Baumann, David

2011-01-01

The objectives of the Technology Watch process are to identify emerging, high-impact technologies that augment current ExMC development efforts, and to work with academia, industry, and other government agencies to accelerate the development of medical care and research capabilities for the mitigation of potential health issues that could occur during space exploration missions. The establishment of collaborations with these entities is beneficial to technology development, assessment and/or insertion. Such collaborations also further NASA s goal to provide a safe and healthy environment for human exploration. The Tech Watch project addresses requirements and capabilities identified by knowledge and technology gaps that are derived from a discrete set of medical conditions that are most likely to occur on exploration missions. These gaps are addressed through technology readiness level assessments, market surveys, collaborations and distributed innovation opportunities. Ultimately, these gaps need to be closed with respect to exploration missions, and may be achieved through technology development projects. Information management is a key aspect to this process where Tech Watch related meetings, research articles, collaborations and partnerships are tracked by the HRP s Exploration Medical Capabilities (ExMC) Element. In 2011, ExMC will be introducing the Tech Watch external website and evidence wiki that will provide access to ExMC technology and knowledge gaps, technology needs and requirements documents.

Gossiping Capabilities

DEFF Research Database (Denmark)

Mogensen, Martin; Frey, Davide; Guerraoui, Rachid

Gossip-based protocols are now acknowledged as a sound basis to implement collaborative high-bandwidth content dissemination: content location is disseminated through gossip, the actual contents being subsequently pulled. In this paper, we present HEAP, HEterogeneity Aware gossip Protocol, where...... nodes dynamically adjust their contribution to gossip dissemination according to their capabilities. Using a continuous, itself gossip-based, approximation of relative capabilities, HEAP dynamically leverages the most capable nodes by (a) increasing their fanouts (while decreasing by the same proportion...... declare a high capability in order to augment their perceived quality without contributing accordingly. We evaluate HEAP in the context of a video streaming application on a 236 PlanetLab nodes testbed. Our results shows that HEAP improves the quality of the streaming by 25% over a standard gossip...

Capabilities and diagnostics of the Sandia Pelletron-raster system

International Nuclear Information System (INIS)

Buckalew, W.H.; Lockwood, G.J.; Luker, S.M.; Ruggles, L.E.; Wyant, F.J.

1984-07-01

The radiation capabilities of the PELLETRON Electron Beam Accelerator have been expanded to include a controllable, variable dimension, beam diffusion option. This rastered beam option has been studied in detail. Beam characteristics have been determined as a function of incident electron beam energy, current, and deflection system parameters. The beam diagnostics required to define any given diffuse beam pattern are accurate and predictable. Recently, utility of this added PELLETRON capability was demonstrated by simulating the effects of complex nuclear reactor accident electron environments on electrical insulation materials similar to those used in nuclear power plants

Experimental studies of the quench behaviour of MgB{sub 2} superconducting wires for fault current limiter applications

Energy Technology Data Exchange (ETDEWEB)

Ye Lin [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Majoros, M [Laboratories for Applied Superconductivity and Magnetism, Ohio State University, Columbus, OH 43210 (United States); Campbell, A M [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Coombs, T [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Astill, D [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Harrison, S [Scientific Magnetics, Culham Science Centre, Culham, Abingdon, Oxfordshire OX14 3DB (United Kingdom); Husband, M [Strategic Research Center (SRC)-Electrical Engineering, Rolls-Royce plc, Derby DE24 8BJ (United Kingdom); Rindfleisch, M [Hyper Tech Research Inc., Columbus, OH 43212 (United States); Tomsic, M [Hyper Tech Research Inc., Columbus, OH 43212 (United States)

2007-07-15

Various MgB{sub 2} wires with different sheath materials provided by Hyper Tech Research Inc., have been tested in the superconducting fault current limiter (SFCL) desktop tester at 24-26 K in a self-field. Samples 1 and 2 are similarly fabricated monofilamentary MgB{sub 2} wires with a sheath of CuNi, except that sample 2 is doped with SiC and Mg addition. Sample 3 is a CuNi sheathed multifilamentary wire with Cu stabilization and Mg addition. All the samples with Nb barriers have the same diameter of 0.83 mm and superconducting fractions ranging from 15% to 27% of the total cross section. They were heat-treated at temperatures of 700 deg. C for a hold time of 20-40 min. Current limiting properties of MgB{sub 2} wires subjected to pulse overcurrents have been experimentally investigated in an AC environment in the self-field at 50 Hz. The quench currents extracted from the pulse measurements were in a range of 200-328 A for different samples, corresponding to an average engineering critical current density (J{sub e}) of around 4.8 x 10{sup 4} A cm{sup -2} at 25 K in the self-field, based on the 1 {mu}V cm{sup -1} criterion. This work is intended to compare the quench behaviour in the Nb-barrier monofilamentary and multifilamentary MgB{sub 2} wires with CuNi and Cu/CuNi sheaths. The experimental results can be applied to the design of fault current limiter applications based on MgB{sub 2} wires.

Enhanced Monte-Carlo-Linked Depletion Capabilities in MCNPX

International Nuclear Information System (INIS)

Fensin, Michael L.; Hendricks, John S.; Anghaie, Samim

2006-01-01

As advanced reactor concepts challenge the accuracy of current modeling technologies, a higher-fidelity depletion calculation is necessary to model time-dependent core reactivity properly for accurate cycle length and safety margin determinations. The recent integration of CINDER90 into the MCNPX Monte Carlo radiation transport code provides a completely self-contained Monte-Carlo-linked depletion capability. Two advances have been made in the latest MCNPX capability based on problems observed in pre-released versions: continuous energy collision density tracking and proper fission yield selection. Pre-released versions of the MCNPX depletion code calculated the reaction rates for (n,2n), (n,3n), (n,p), (n,a), and (n,?) by matching the MCNPX steady-state 63-group flux with 63-group cross sections inherent in the CINDER90 library and then collapsing to one-group collision densities for the depletion calculation. This procedure led to inaccuracies due to the miscalculation of the reaction rates resulting from the collapsed multi-group approach. The current version of MCNPX eliminates this problem by using collapsed one-group collision densities generated from continuous energy reaction rates determined during the MCNPX steady-state calculation. MCNPX also now explicitly determines the proper fission yield to be used by the CINDER90 code for the depletion calculation. The CINDER90 code offers a thermal, fast, and high-energy fission yield for each fissile isotope contained in the CINDER90 data file. MCNPX determines which fission yield to use for a specified problem by calculating the integral fission rate for the defined energy boundaries (thermal, fast, and high energy), determining which energy range contains the majority of fissions, and then selecting the appropriate fission yield for the energy range containing the majority of fissions. The MCNPX depletion capability enables complete, relatively easy-to-use depletion calculations in a single Monte Carlo code

Experimental Study of Current Discharge Behavior and Hard X-ray Anisotropy by APF Plasma Focus Device

Science.gov (United States)

Habibi, M.; Amrollahi, R.; Attaran, M.

2009-03-01

Amirkabir (APF) is a new Mather-type plasma focus device (16 kV, 36 μf, and 115 nH). In this work we present some experimental results as variation of discharge current signal respect to applied voltage at the optimum pressure, focusing time of plasma versus gas pressure, and variations of current discharge with different insulator sleeve dimensions. As we prospected optimum pressure tending to increase as we tried to higher voltage levels. The time taken by the current sheath to lift-off the insulator surface and therefore quality of pinched plasma depends on the length of the insulator sleeve. The results show that the insulator diameter can influence on pinch quality. Behavior of hard X-ray (HXR) signals with the pressure and also anisotropy of HXR investigated by the use of two scintillation detectors. The distribution of HXR intensity shows a large anisotropy with a maximum intensity between 22.5° and 45° and also between -22.5° and -67.5°.

Rights, goals, and capabilities

NARCIS (Netherlands)

van Hees, M.V.B.P.M

This article analyses the relationship between rights and capabilities in order to get a better grasp of the kind of consequentialism that the capability theory represents. Capability rights have been defined as rights that have a capability as their object (rights to capabilities). Such a

Neurocognitive capabilities modulate the integration of evidence in schizophrenia

NARCIS (Netherlands)

Eifler, Sarah; Rausch, Franziska; Schirmbeck, Frederike; Veckenstedt, Ruth; Englisch, Susanne; Meyer-Lindenberg, Andreas; Kirsch, Peter; Zink, Mathias

2014-01-01

Previous studies have demonstrated a cognitive bias in the integration of disconfirmatory evidence (BADE) in patients with schizophrenia. This bias has been associated with delusions. So far, it is unclear how the integration of evidence is associated with neurocognitive capabilities. In the current

Assessment of Mobile Accident Response Capability

International Nuclear Information System (INIS)

1983-03-01

This report presents the results of a DOE-sponsored assessment of nuclear accident response resources. It identifies the mobile resources that could be required to respond to different types of nuclear accidents including major ones like TMI-2, identifies the resources currently available and makes recommendations for the design and construction of additional mobile accident response resources to supplement those already in existence. This project is referred to as the Mobile Accident Response Capability (MARC) program

Development of eddy current probe for fiber orientation assessment in carbon fiber composites

Science.gov (United States)

Wincheski, Russell A.; Zhao, Selina

2018-04-01

Measurement of the fiber orientation in a carbon fiber composite material is crucial in understanding the load carrying capability of the structure. As manufacturing conditions including resin flow and molding pressures can alter fiber orientation, verification of the as-designed fiber layup is necessary to ensure optimal performance of the structure. In this work, the development of an eddy current probe and data processing technique for analysis of fiber orientation in carbon fiber composites is presented. A proposed directional eddy current probe is modeled and its response to an anisotropic multi-layer conductor simulated. The modeling results are then used to finalize specifications of the eddy current probe. Experimental testing of the fabricated probe is presented for several samples including a truncated pyramid part with complex fiber orientation draped to the geometry for resin transfer molding. The inductively coupled single sided measurement enables fiber orientation characterization through the thickness of the part. The fast and cost-effective technique can be applied as a spot check or as a surface map of the fiber orientations across the structure. This paper will detail the results of the probe design, computer simulations, and experimental results.

Treating the Capability for Suicide: A Vital and Understudied Frontier in Suicide Prevention.

Science.gov (United States)

Anestis, Michael D; Law, Keyne C; Jin, Hyejin; Houtsma, Claire; Khazem, Lauren R; Assavedo, Brittney L

2017-10-01

Current efforts at suicide prevention center largely on reducing suicidal desire among individuals hospitalized for suicidality or being treated for related psychopathology. Such efforts have yielded evidence-based treatments, and yet the national suicide rate has continued to climb. We propose that this disconnect is heavily influenced by an unmet need to consider population-level interventions aimed at reducing the capability for suicide. Drawing on lessons learned from other public health phenomena that have seen drastic declines in frequency in recent decades (HIV, lung cancer, motor vehicle accidents), we propose that current suicidality treatment efforts trail current suicidality theories in their lack of focus on the extent to which individuals thinking about suicide are capable of transitioning from ideation to attempt. We summarize extant evidence for specific capability-centered approaches (e.g., means safety) and propose other options for improving our ability to address this largely overlooked variable. We also note that population-level approaches in this regard would represent an important opportunity to decrease risk in individuals who either lack access to evidence-based care or underreport suicidal ideation, as a reduced capability for suicide would theoretically diminish the potency of suicidal desire and, in this sense, lower the odds of a transition from ideation to attempt. © 2016 The American Association of Suicidology.

A Combined Experimental and Finite Element Analysis Method for the Estimation of Eddy-Current Loss in NdFeB Magnets

Directory of Open Access Journals (Sweden)

Radu Fratila

2014-05-01

Full Text Available NdFeB permanent magnets (PMs are widely used in high performance electrical machines, but their relatively high conductivity subjects them to eddy current losses that can lead to magnetization loss. The Finite Element (FE method is generally used to quantify the eddy current loss of PMs, but it remains quite difficult to validate the accuracy of the results with complex devices. In this paper, an experimental test device is used in order to extract the eddy current losses that are then compared with those of a 3D FE model.

A combined experimental and finite element analysis method for the estimation of eddy-current loss in NdFeB magnets.

Science.gov (United States)

Fratila, Radu; Benabou, Abdelkader; Tounzi, Abdelmounaïm; Mipo, Jean-Claude

2014-05-14

NdFeB permanent magnets (PMs) are widely used in high performance electrical machines, but their relatively high conductivity subjects them to eddy current losses that can lead to magnetization loss. The Finite Element (FE) method is generally used to quantify the eddy current loss of PMs, but it remains quite difficult to validate the accuracy of the results with complex devices. In this paper, an experimental test device is used in order to extract the eddy current losses that are then compared with those of a 3D FE model.

Building Visual Artists’ Resilience Capabilities: Current Educator Strategies and Methods

Directory of Open Access Journals (Sweden)

Eileen Maree Siddins

2016-07-01

Full Text Available Enrolments in higher education programs in the creative and performing arts are increasing in many countries. Yet graduates of these degrees, who enter the broad sector known as the creative industries, face particular challenges in terms of securing long-term and sustainable employment. In addition, creative and performing artists face a range of mental challenges, caused by such factors as: the solitary nature of much creative practice, critical feedback by audiences and gatekeepers, or the general pressures associated with maintaining artistic relevance or integrity. The concepts of resilience and professional wellbeing are therefore highly relevant to those who pursue a career in creative industries, and while there has been an emerging body of work in this area, to date it has focussed on the performing arts area (e.g. music, theatre. Hence, in order to expand knowledge relevant to resilience and artists, this paper sets out to explore the extent to which current educators in the Australian context specifically address these issues within higher visual arts curricula; specifically the areas of illustration, design, film and photography. This was achieved via interviews with seventeen current academics working in these areas. The findings propose that higher education providers of programs in the visual arts consider placing a stronger emphasis on the embedded development of resilience and professional wellbeing capacities.

Current experimental situation in heavy-ion reactions

International Nuclear Information System (INIS)

Scott, D.K.

1978-06-01

A detailed survey of the present experimental situation in heavy-ion physics is presented. The discussion begins by considering the simple excitation of discrete states in elastic scattering, transfer, and compound-nucleus reactions; it then turns to more drastic perturbations of the nucleus high in the continuum through fusion, fission, and deeply inelastic scattering, and concludes with the (possibly) limiting asymptotic phenomena of relativistic heavy-ion collisions. 138 figures, 5 tables, 451 references

'I think it will eventually be done away with': Attitudes among healthcare professionals towards the current system of animal experimentation.

Science.gov (United States)

Dignon, Andrée

2016-08-01

This article describes a study of attitudes to the current system of animal experimentation (for the production of health interventions) among 52 UK healthcare professionals. These healthcare professionals participated in three separate focus groups (of 18, 17 and 17 participants) and were invited to respond to the question 'what is your opinion about the current system of animal testing?' The study focused specifically on their views of the current system (rather than their views of animal testing in general). The healthcare professionals were critical of the current system, particularly with regard to regulation, secrecy, validity, unnecessary suffering and welfare. © The Author(s) 2014.

An embedded acceleration measurement capability for EXPRESS Rack Payloads

International Nuclear Information System (INIS)

Foster, William M. II; Sutliff, Thomas J.

2000-01-01

The International Space Station provides a microgravity environment allowing long duration studies to be made on phenomena masked by the presence of earth's gravitational effects. Studies are also enabled in areas requiring a substantial decrease in steady-state and vibratory acceleration environments. In anticipation microgravity science experiments being targeted for EXPRESS (EXpedite the PRocessing of Experiments to Space Station) Racks, a capability has been provided to simplify and conduct a consistent measurement of the microgravity environment for payloads. The Space Acceleration Measurement System-II (SAMS-II) project has collaborated with the EXPRESS Rack Project to embed an electronics unit within the four EXPRESS Racks equipped with Active Rack Isolation Systems (ARIS). Each SAMS-II unit provides a standardized means for payload acceleration measurements to be acquired. Access to this capability is via front panel connections similar to those of power, data and water cooling provided for EXPRESS payloads. Furthermore, an International Subrack Interface Standard (ISIS) drawer configuration has been developed to provide measurement capability to the non-ARIS equipped EXPRESS Racks, as well as to other ISIS-configured racks, for non-isolated experimental measurement needs. This paper describes the SAMS-II acceleration measurement capabilities provided to ISS users and, in particular, to the EXPRESS Rack community

Capability ethics

NARCIS (Netherlands)

I.A.M. Robeyns (Ingrid)

2012-01-01

textabstractThe capability approach is one of the most recent additions to the landscape of normative theories in ethics and political philosophy. Yet in its present stage of development, the capability approach is not a full-blown normative theory, in contrast to utilitarianism, deontological

The SCEC Community Modeling Environment (SCEC/CME) - An Overview of its Architecture and Current Capabilities

Science.gov (United States)

Maechling, P. J.; Jordan, T. H.; Minster, B.; Moore, R.; Kesselman, C.; SCEC ITR Collaboration

2004-12-01

these models. In some cases, the CME system also provides alternatives to the SCEC community models. The CME system hosts a collection of community geophysical software codes. These codes include seismic hazard analysis (SHA) programs developed by the SCEC/USGS OpenSHA group. Also, the CME system hosts anelastic wave propagation codes including Kim Olsen's Finite Difference code and Carnegie Mellon's Hercules Finite Element tool chain. The CME system can execute a workflow, that is, a series of geophysical computations using the output of one processing step as the input to a subsequent step. Our workflow capability utilizes grid-based computing software that can submit calculations to a pool of computing resources as well as data management tools that help us maintain an association between data files and metadata descriptions of those files. The CME system maintains, and provides access to, a collection of valuable geophysical data sets. The current CME Digital Library holdings include a collection of 60 ground motion simulation results calculated by a SCEC/PEER working group and a collection of Greens Functions calculated for 33 TriNet broadband receiver sites in the Los Angeles area.

Calculated fraction of an incident current pulse that will be accelerated by an electron linear accelerator and comparisons with experimental data

International Nuclear Information System (INIS)

Alsmiller, R.G. Jr.; Alsmiller, F.S.; Lewis, T.A.

1986-05-01

In a series of previous papers, calculated results obtained using a one-dimensional ballistic model were presented to aid in the design of a prebuncher for the Oak Ridge Electron Linear Accelerator. As part of this work, a model was developed to provide limits on the fraction of an incident current pulse that would be accelerated by the existing accelerator. In this paper experimental data on this fraction are presented and the validity of the model developed previously is tested by comparing calculated and experimental data. Part of the experimental data is used to fix the physical parameters in the model and then good agreement between the calculated results and the rest of the experimental data is obtained

Dynamic Capabilities

DEFF Research Database (Denmark)

Grünbaum, Niels Nolsøe; Stenger, Marianne

2013-01-01

The findings reveal a positive relationship between dynamic capabilities and innovation performance in the case enterprises, as we would expect. It was, however, not possible to establish a positive relationship between innovation performance and profitability. Nor was there any positive...... relationship between dynamic capabilities and profitability....

Experimental and theoretical studies of a high temperature cesium-barium tacitron, with application to low voltage-high current inversion

International Nuclear Information System (INIS)

Murray, C.S.; El-Genk, M.S.

1994-02-01

A low voltage/high current switch refer-red as ''Cs-Ba tacitron'' is studied for use as a dc to ac inverter in high temperature and/or ionizing radiation environments. The operational characteristics of the Cs-Ba tacitron as a switch were investigated experimentally in three modes: (a) breakdown mode, (b) I-V mode, and (c) current modulation mode. Operation parameters measured include switching frequencies up to 20 kHz, hold-off voltages up to 200 V, current densities in excess of 15 A/CM 2 , switch power density of 1 kW/cm 2 , and a switching efficiency in excess of 90 % at collector voltages greater than 30 V. Also, if the discharge current is circuit limited to a value below the maximum thermal emission current density, the voltage drop is constant and below 3 V

Reactivity Insertion Accident (RIA) Capability Status in the BISON Fuel Performance Code

Energy Technology Data Exchange (ETDEWEB)

Williamson, Richard L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Folsom, Charles Pearson [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pastore, Giovanni [Idaho National Lab. (INL), Idaho Falls, ID (United States); Veeraraghavan, Swetha [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-05-01

One of the Challenge Problems being considered within CASL relates to modelling and simulation of Light Water Reactor LWR) fuel under Reactivity Insertion Accident (RIA) conditions. BISON is the fuel performance code used within CASL for LWR fuel under both normal operating and accident conditions, and thus must be capable of addressing the RIA challenge problem. This report outlines required BISON capabilities for RIAs and describes the current status of the code. Information on recent accident capability enhancements, application of BISON to a RIA benchmark exercise, and plans for validation to RIA behavior are included.

PHISICS multi-group transport neutronic capabilities for RELAP5

Energy Technology Data Exchange (ETDEWEB)

Epiney, A.; Rabiti, C.; Alfonsi, A.; Wang, Y.; Cogliati, J.; Strydom, G. [Idaho National Laboratory (INL), 2525 N. Fremont Ave., Idaho Falls, ID 83402 (United States)

2012-07-01

PHISICS is a neutronic code system currently under development at INL. Its goal is to provide state of the art simulation capability to reactor designers. This paper reports on the effort of coupling this package to the thermal hydraulic system code RELAP5. This will enable full prismatic core and system modeling and the possibility to model coupled (thermal-hydraulics and neutronics) problems with more options for 3D neutron kinetics, compared to the existing diffusion theory neutron kinetics module in RELAP5 (NESTLE). The paper describes the capabilities of the coupling and illustrates them with a set of sample problems. (authors)

Capabilities and Incapabilities of the Capabilities Approach to Health Justice.

Science.gov (United States)

Selgelid, Michael J

2016-01-01

This first part of this article critiques Sridhar Venkatapuram's conception of health as a capability. It argues that Venkatapuram relies on the problematic concept of dignity, implies that those who are unhealthy lack lives worthy of dignity (which seems politically incorrect), sets a low bar for health, appeals to metaphysically problematic thresholds, fails to draw clear connections between appealed-to capabilities and health, and downplays the importance/relevance of health functioning. It concludes by questioning whether justice entitlements should pertain to the capability for health versus health achievements, challenging Venkatapuram's claims about the strength of health entitlements, and demonstrating that the capabilities approach is unnecessary to address social determinants of health. © 2016 John Wiley & Sons Ltd.

IntelliTable: Inclusively-Designed Furniture with Robotic Capabilities.

Science.gov (United States)

Prescott, Tony J; Conran, Sebastian; Mitchinson, Ben; Cudd, Peter

2017-01-01

IntelliTable is a new proof-of-principle assistive technology system with robotic capabilities in the form of an elegant universal cantilever table able to move around by itself, or under user control. We describe the design and current capabilities of the table and the human-centered design methodology used in its development and initial evaluation. The IntelliTable study has delivered robotic platform programmed by a smartphone that can navigate around a typical home or care environment, avoiding obstacles, and positioning itself at the user's command. It can also be configured to navigate itself to pre-ordained places positions within an environment using ceiling tracking, responsive optical guidance and object-based sonar navigation.

Assessing the Impact of IT Competency on Organizational Learning Capability of Indonesian Manufacturing Firms

Directory of Open Access Journals (Sweden)

Alizar Hasan

2010-01-01

Full Text Available This paper attempt to assessing the impact of IT competency on organizational learning capability by using the measurement scale that have been developed by Tippins et al. and Gomes et al. These studies cover a sample of 192 manufacturing firms. IT competencies are classified into three dimensions: IT knowledge, IT operations, and IT objects, and organizational learning capability are classified into four dimensions: Managerial commitment, System perspec-tive, Openness and experimentation, and Knowledge transfer and integration. The result of factor analysis on IT competency and Organizational learning capability show that all items have high loading only on a single factor with ranging from .60 to .84. The findings revealed that IT competency positively and significantly influences the organizational learning capability of Indonesian manufacturing firms.

Current Monitoring System for ITER Like ICRH Antenna

International Nuclear Information System (INIS)

Argouarch, A.

2006-01-01

On TS antennas, the power transfer optimization from ICRH antenna to Plasma load is performed using feedback internal matching system. Experimental handling is required to mach the reactive impedance accordingly to the fluctuant plasma loading. As part of the development of the new ICRH prototype antenna, an additional measurement system based on Rogowski coils was developed to monitor the current distribution in antenna straps. The objective is to control module and phase of the antenna current straps with measurement provided by the coil system. Matching capacitors values, generators power and phase can also be controlled using the output of the devices, improving the real time matching control of the array. This paper details the new measurement layout, the Rogowski coil, and the whole system connected on each strap design for RF currents measurement between 40 MHz - 60 MHz for maximum amplitude of 1 kA. On the new ICRH prototype antenna, the measurement coils are coupled to the point where the strap currents are short circuited to the frame. The module and phase measurements are performed with the coils by direct magnetic induction in a vacuum and high temperature environment. Also, the Rogowski coils were characterized at low level power with vector network analyzer and the design adapted in order to obtain a controlled and reproducible gain in the desire bandwidth. The transconductive function is established with an experimental gain near -80 dB between primary circuit and inductive signal generated by the Rogowski coil. In a second step, the system with its associated electronic was qualified under high RF power. First results with high RF current (closed to 500 A at 57 MHz) match the desire Rogowski coil response. Compromises with electrical response at low power level and the coil under thermal/RF stresses were the most challenging part of the development. The overall response of the system and the current module/phase measurements are promising. A proper

Capabilities for Strategic Adaptation

DEFF Research Database (Denmark)

Distel, Andreas Philipp

This dissertation explores capabilities that enable firms to strategically adapt to environmental changes and preserve competitiveness over time – often referred to as dynamic capabilities. While dynamic capabilities being a popular research domain, too little is known about what these capabiliti...

Clinical experimentation with aerosol antibiotics: current and future methods of administration

Directory of Open Access Journals (Sweden)

Zarogoulidis P

2013-10-01

Full Text Available Paul Zarogoulidis,1,2 Ioannis Kioumis,1 Konstantinos Porpodis,1 Dionysios Spyratos,1 Kosmas Tsakiridis,3 Haidong Huang,4 Qiang Li,4 J Francis Turner,5 Robert Browning,6 Wolfgang Hohenforst-Schmidt,7 Konstantinos Zarogoulidis1 1Pulmonary Department, G Papanikolaou General Hospital, Aristotle University of Thessaloniki, Thessaloniki, Greece; 2Department of Interventional Pneumology, Ruhrlandklinik, West German Lung Center, University Hospital, University Duisburg-Essen, Essen, Germany; 3Cardiothoracic Surgery Department, Saint Luke Private Hospital of Health Excellence, Thessaloniki, Greece; 4Department of Respiratory Diseases, Shanghai Hospital/First Affiliated Hospital of the Second Military Medical University, Shanghai, People’s Republic of China; 5Pulmonary Medicine, University of Nevada School of Medicine, National Supercomputing Center for Energy and the Environment University of Nevada, Las Vegas, NV, USA; 6Pulmonary and Critical Care Medicine, Interventional Pulmonology, National Naval Medical Center, Walter Reed Army Medical Center, Bethesda, MD, USA; 7II Medical Department, Regional Clinic of Coburg, University of Wuerzburg, Coburg, Germany Abstract: Currently almost all antibiotics are administered by the intravenous route. Since several systems and situations require more efficient methods of administration, investigation and experimentation in drug design has produced local treatment modalities. Administration of antibiotics in aerosol form is one of the treatment methods of increasing interest. As the field of drug nanotechnology grows, new molecules have been produced and combined with aerosol production systems. In the current review, we discuss the efficiency of aerosol antibiotic studies along with aerosol production systems. The different parts of the aerosol antibiotic methodology are presented. Additionally, information regarding the drug molecules used is presented and future applications of this method are discussed

Technical note: An experimental set-up to measure latent and sensible heat fluxes from (artificial plant leaves

Directory of Open Access Journals (Sweden)

S. J. Schymanski

2017-07-01

Full Text Available Leaf transpiration and energy exchange are coupled processes that operate at small scales yet exert a significant influence on the terrestrial hydrological cycle and climate. Surprisingly, experimental capabilities required to quantify the energy–transpiration coupling at the leaf scale are lacking, challenging our ability to test basic questions of importance for resolving large-scale processes. The present study describes an experimental set-up for the simultaneous observation of transpiration rates and all leaf energy balance components under controlled conditions, using an insulated closed loop miniature wind tunnel and artificial leaves with pre-defined and constant diffusive conductance for water vapour. A range of tests documents the above capabilities of the experimental set-up and points to potential improvements. The tests reveal a conceptual flaw in the assumption that leaf temperature can be characterized by a single value, suggesting that even for thin, planar leaves, a temperature gradient between the irradiated and shaded or transpiring and non-transpiring leaf side can lead to bias when using observed leaf temperatures and fluxes to deduce effective conductances to sensible heat or water vapour transfer. However, comparison of experimental results with an explicit leaf energy balance model revealed only minor effects on simulated leaf energy exchange rates by the neglect of cross-sectional leaf temperature gradients, lending experimental support to our current understanding of leaf gas and energy exchange processes.

Synthetic methods for beam to beam power balancing capability of large laser facilities

International Nuclear Information System (INIS)

Chen Guangyu; Zhang Xiaomin; Zhao Runchang; Zheng Wanguo; Yang Xiaoyu; You Yong; Wang Chengcheng; Shao Yunfei

2011-01-01

To account for output power balancing capability of large laser facilities, a synthetic method with beam to beam root-mean-square is presented. Firstly, a conversion process for the facilities from original data of beam powers to regular data is given. The regular data contribute to the normal distribution approximately, and then a corresponding simple method of root-mean-square for beam to beam power balancing capability is given.Secondly, based on theory of total control charts and cause-selecting control charts, control charts with root-mean-square are established which show short-term variety of power balancing capability of the facilities. Mean rate of failure occurrence is also defined and used to describe long-term trend of global balancing capabilities of the facilities. Finally, advantages of the intuitive and efficient diagnosis for synthetic methods are illustrated by analysis of experimental data. (authors)

Current status and prospects of research reactors

International Nuclear Information System (INIS)

Gabaraev, A.B.; Cherepnin, Yu.S.; Tretyakov, I.T.; Khmelshikov, V.V.; Dollezhal, N.A.

2009-01-01

Full text: The first nuclear research reactors (RR) appeared in the 1940s. Their initial purpose was to provide knowledge of the main processes associated with neutron-induced nuclear reactions. Later, the rang of problems addressed expanded substantially. Besides fundamental research in the properties of matter, such reactors are successfully used for dealing with problems in the fields of materials science, nuclear engineering, medicine, isotope production, education, etc. Over the whole period of RR fleet growth, more than six hundred nuclear research facilities were built in 70 countries of the world. As of the end of 2008, the number of Russian research reactors in service was about 20% of the globally operating RR fleet. This paper discusses the current status of the world's RR fleet and describes the capabilities of the experimental reactor facilities existing in Russia. In the 21st century, research reactors will remain in demand to solve scientific and technological problems for innovative development of society. The emerging renaissance of nuclear power, the expanding RR uses for production of isotopes and other applications, the increase in the number of countries willing to use nuclear technologies in energy production, industry and science - all contribute to a rebirth of interest in research reactors. One of the ways to improve the experimental capabilities lies in radical upgrading of the reactor facilities with qualitative changes in the main neutronic characteristics of the core. The associated design approaches are illustrated with the example of the IBR-2M reactor at the JNRI in Dubna. The imperative need restricting the spread of nuclear threat leads us to give up using highly enriched uranium in most research reactors. Development of RR fuel with reduced enrichment in uranium has been one of the priority objectives of NIKIET for many years. This paper presents the latest results obtained along these lines, as applied to pool-type research

Filling of a Salt-withdrawal Minibasin on the Continental Slope by Turbidity Currents: Experimental study

Science.gov (United States)

Violet, J.; Evans, C.; Sheets, B.; Paola, C.; Pratson, L.; Parker, G.

2001-12-01

We report on the transport and deposition of sediment by turbidity currents in an experimental basin designed to model salt-withdrawal minibasins found along the northern continental slope of the Gulf of Mexico. The experiment was performed in two stages in the subsiding EXperimental EarthScape facility (XES) at St. Anthony Falls Laboratory, University of Minnesota. Stage I consisted of 15 turbidity-current events in the following sequence: one 36-minute continuous event, six 1.85-minute small pulses, one 3.8-minute large pulse, six more small pulses, one more large pulse, and finally one more continuous event. The continuous events and the small pulses had a flow discharge of 1.5 liters/s and the large pulse had a flow discharge of 4.5 liters/s. The flows all had a volume concentration of sediment of 0.05. The sediment comprised three grades of silica with nominal diameters of 20 microns (45%), 45 microns (40%) and 110 microns (15%). The basin subsided continuously during Stage I. Stage II consisted of the same sequence of events as Stage I, but with no further subsidence. The sand content was eliminated during the latter part of Stage II. The deposit was imaged as it developed during the experiment using high-frequency sonar. The sonar records show indications of incipient self-channelization as well as clear erosion, bypass, and deposition. Erosion was promoted by large pulse events and the absence of sand. The deposit shows well developed lamination and normal grading.

A variable capacitance based modeling and power capability predicting method for ultracapacitor

Science.gov (United States)

Liu, Chang; Wang, Yujie; Chen, Zonghai; Ling, Qiang

2018-01-01

Methods of accurate modeling and power capability predicting for ultracapacitors are of great significance in management and application of lithium-ion battery/ultracapacitor hybrid energy storage system. To overcome the simulation error coming from constant capacitance model, an improved ultracapacitor model based on variable capacitance is proposed, where the main capacitance varies with voltage according to a piecewise linear function. A novel state-of-charge calculation approach is developed accordingly. After that, a multi-constraint power capability prediction is developed for ultracapacitor, in which a Kalman-filter-based state observer is designed for tracking ultracapacitor's real-time behavior. Finally, experimental results verify the proposed methods. The accuracy of the proposed model is verified by terminal voltage simulating results under different temperatures, and the effectiveness of the designed observer is proved by various test conditions. Additionally, the power capability prediction results of different time scales and temperatures are compared, to study their effects on ultracapacitor's power capability.

Technique development for modulus, microcracking, hermeticity, and coating evaluation capability characterization of SiC/SiC tubes

Energy Technology Data Exchange (ETDEWEB)

Hu, Xunxiang [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Ang, Caen K. [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Singh, Gyanender P. [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States); Katoh, Yutai [Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States)

2016-08-01

Driven by the need to enlarge the safety margins of nuclear fission reactors in accident scenarios, research and development of accident-tolerant fuel has become an important topic in the nuclear engineering and materials community. A continuous-fiber SiC/SiC composite is under consideration as a replacement for traditional zirconium alloy cladding owing to its high-temperature stability, chemical inertness, and exceptional irradiation resistance. An important task is the development of characterization techniques for SiC/SiC cladding, since traditional work using rectangular bars or disks cannot directly provide useful information on the properties of SiC/SiC composite tubes for fuel cladding applications. At Oak Ridge National Laboratory, experimental capabilities are under development to characterize the modulus, microcracking, and hermeticity of as-fabricated, as-irradiated SiC/SiC composite tubes. Resonant ultrasound spectroscopy has been validated as a promising technique to evaluate the elastic properties of SiC/SiC composite tubes and microcracking within the material. A similar technique, impulse excitation, is efficient in determining the basic mechanical properties of SiC bars prepared by chemical vapor deposition; it also has potential for application in studying the mechanical properties of SiC/SiC composite tubes. Complete evaluation of the quality of the developed coatings, a major mitigation strategy against gas permeation and hydrothermal corrosion, requires the deployment of various experimental techniques, such as scratch indentation, tensile pulling-off tests, and scanning electron microscopy. In addition, a comprehensive permeation test station is being established to assess the hermeticity of SiC/SiC composite tubes and to determine the H/D/He permeability of SiC/SiC composites. This report summarizes the current status of the development of these experimental capabilities.

Experimental Neutrino Physics

Energy Technology Data Exchange (ETDEWEB)

Wilkes, Richard Jeffrey [Univ. of Washington, Seattle, WA (United States)

2017-11-15

The University of Washington (UW) HEP neutrino group performed experimental research on the physics of neutrinos, using the capabilities offered by the T2K Experiment and the Super-Kamiokande Neutrino Observatory. The UW group included senior investigator R. J. Wilkes, two PhD students, four MS degree students, and a research engineer, all of whom are members of the international scientific collaborations for T2K and Super-Kamiokande. During the period of support, within T2K we pursued new precision studies sensitive to new physics, going beyond the limits of current measurements of the fundamental neutrino oscillation parameters (mass differences and mixing angles). We began efforts to measure (or significantly determine the absence of) 1 the CP-violating phase parameter δCP and determine the neutrino mass hierarchy. Using the Super-Kamiokande (SK) detector we pursued newly increased precision in measurement of neutrino oscillation parameters with atmospheric neutrinos, and extended the current reach in searches for proton decay, in addition to running the most sensitive supernova watch instrument [Scholberg 2012], performing other astrophysical neutrino studies, and analyzing beam-induced events from T2K. Overall, the research addressed central questions in the field of particle physics. It included the training of graduate students (both PhD and professional MS degree students), and postdoctoral researchers. Undergraduate students also participated as laboratory assistants.

Size and transportation capabilities of the existing US cask fleet

International Nuclear Information System (INIS)

Danese, F.L.; Johnson, P.E.; Joy, D.S.

1990-01-01

This study investigates the current spent nuclear fuel cask fleet capability in the United States. In addition, it assesses the degree to which the current fleet would be available, as a contingency, until proposed Office of Civilian Radioactive Waste Management casks become operational. A limited fleet of ten spent fuel transportation casks is found to be readily available for use in Federal waste management efforts over the next decade

Current density monitor for intense relativistic electron beams

International Nuclear Information System (INIS)

Fiorito, R.B.; Raleigh, M.; Seltzer, S.M.

1986-01-01

We describe a new type of electric probe which is capable of measuring the time-resolved current density profile of a stable, reproducible, high-energy (>4-MeV) high-current (>1-kA) electron beam. The sensing element of this probe is an open-ended but capped-off 50-Ω coaxial line constructed of graphite. The graphite sensor is 4.3 mm in diameter, 6 cm long, and is range thin to the primary beam electrons. The probe produces a signal proportional to the intercepted beam current. When the sensor is scanned radially through the beam during repeated pulses, a curve of signal versus depth of insertion is produced from which the radial current density profile can be determined. Measurements are presented of the profile of the electron beam from the Experimental Test Accelerator (4.5 MeV, 10 kA) at Lawrence Livermore National Laboratory. Good agreement is shown between measurements made with this probe and the beam radius as predicted by transport codes. The advantage of the electric probe lies in its ruggedness, simplicity, inherent fast rise time, and low cost. In contrast to other systems it requires no radiation shielding, water cooling, or auxiliary support equipment to operate in an intense beam environment

Current Parental Depression and Offspring Perceived Self-Competence: A Quasi-Experimental Examination

Science.gov (United States)

Class, Quetzal A.; D’Onofrio, Brian M.; Singh, Amber L.; Ganiban, Jody M.; Spotts, E. L.; Lichtenstein, Paul; Reiss, David; Neiderhiser, Jenae M.

2013-01-01

A genetically-informed, quasi-experimental design was used to examine the genetic and environmental processes underlying associations between current parental depressive symptoms and offspring perceived self-competence. Participants, drawn from a population-based Swedish sample, were 852 twin pairs and their male (52%) and female offspring aged 15.7 ± 2.4 years. Parental depressive symptoms were measured using the Center for Epidemiological Studies Depression scale. Offspring perceived self-competence was measured using a modified Harter Perceived Competence Scale. Cousin comparisons and Children of Twins (CoT) designs suggested that associations between maternal depressive symptoms and offspring perceived self-competence were due to shared genetic/environmental liability. The mechanism responsible for father-offspring associations, however, was independent of genetic factors and of extended-family environmental factors, supporting a causal inference. Thus, mothers and fathers may impact offspring perceived self-competence via different mechanisms and unmeasured genetic and environmental selection factors must be considered when studying the intergenerational transmission of cognitive vulnerabilities for depression. PMID:22692226

Current parental depression and offspring perceived self-competence: a quasi-experimental examination.

Science.gov (United States)

Class, Quetzal A; D'Onofrio, Brian M; Singh, Amber L; Ganiban, Jody M; Spotts, E L; Lichtenstein, Paul; Reiss, David; Neiderhiser, Jenae M

2012-09-01

A genetically-informed, quasi-experimental design was used to examine the genetic and environmental processes underlying associations between current parental depressive symptoms and offspring perceived self-competence. Participants, drawn from a population-based Swedish sample, were 852 twin pairs and their male (52 %) and female offspring aged 15.7 ± 2.4 years. Parental depressive symptoms were measured using the Center for Epidemiological Studies Depression scale. Offspring perceived self-competence was measured using a modified Harter Perceived Competence Scale. Cousin comparisons and Children of Twins designs suggested that associations between maternal depressive symptoms and offspring perceived self-competence were due to shared genetic/environmental liability. The mechanism responsible for father-offspring associations, however, was independent of genetic factors and of extended family environmental factors, supporting a causal inference. Thus, mothers and fathers may impact offspring perceived self-competence via different mechanisms and unmeasured genetic and environmental selection factors must be considered when studying the intergenerational transmission of cognitive vulnerabilities for depression.

Investigation of steel to dielectric transition using microminiature eddy-current converter

Directory of Open Access Journals (Sweden)

Malikov Vladimir

2018-01-01

Full Text Available The research aims to develop a microminiature converter for electrical steel investigation. The research topic is considered relevant due to the need for evaluation and forecasting of safe operating life of electric steel products. The authors determined the capability to study steel characteristics at different depths based on variations of eddy-current converter amplitude at the steel-dielectric boundary. A microminiature transformer-type converter was designed, which enables to perform local investigations of ferromagnetic materials using eddy-current method based on local studies of the steel electrical conductivity. Having the designed converter as a basis, a hardware-software complex was built to perform experimental studies of steel at the interface boundary. A system was developed for automated converter relocation above the studied object at a specified velocity. Test results are reported for a specimen with continuous and discrete measurements taken at different frequencies. Response dependence of eddy-current converter was found to demonstrate non-linear behavior at steel to dielectric transition. The effect of gap between the eddy-current converter and the test object is investigated.

NASA Stennis Space Center Integrated System Health Management Test Bed and Development Capabilities

Science.gov (United States)

Figueroa, Fernando; Holland, Randy; Coote, David

2006-01-01

Integrated System Health Management (ISHM) is a capability that focuses on determining the condition (health) of every element in a complex System (detect anomalies, diagnose causes, prognosis of future anomalies), and provide data, information, and knowledge (DIaK)-not just data-to control systems for safe and effective operation. This capability is currently done by large teams of people, primarily from ground, but needs to be embedded on-board systems to a higher degree to enable NASA's new Exploration Mission (long term travel and stay in space), while increasing safety and decreasing life cycle costs of spacecraft (vehicles; platforms; bases or outposts; and ground test, launch, and processing operations). The topics related to this capability include: 1) ISHM Related News Articles; 2) ISHM Vision For Exploration; 3) Layers Representing How ISHM is Currently Performed; 4) ISHM Testbeds & Prototypes at NASA SSC; 5) ISHM Functional Capability Level (FCL); 6) ISHM Functional Capability Level (FCL) and Technology Readiness Level (TRL); 7) Core Elements: Capabilities Needed; 8) Core Elements; 9) Open Systems Architecture for Condition-Based Maintenance (OSA-CBM); 10) Core Elements: Architecture, taxonomy, and ontology (ATO) for DIaK management; 11) Core Elements: ATO for DIaK Management; 12) ISHM Architecture Physical Implementation; 13) Core Elements: Standards; 14) Systematic Implementation; 15) Sketch of Work Phasing; 16) Interrelationship Between Traditional Avionics Systems, Time Critical ISHM and Advanced ISHM; 17) Testbeds and On-Board ISHM; 18) Testbed Requirements: RETS AND ISS; 19) Sustainable Development and Validation Process; 20) Development of on-board ISHM; 21) Taxonomy/Ontology of Object Oriented Implementation; 22) ISHM Capability on the E1 Test Stand Hydraulic System; 23) Define Relationships to Embed Intelligence; 24) Intelligent Elements Physical and Virtual; 25) ISHM Testbeds and Prototypes at SSC Current Implementations; 26) Trailer

Instrumented tube burns: theoretical and experimental observations

Energy Technology Data Exchange (ETDEWEB)

Yarrington, Cole Davis [Los Alamos National Laboratory; Obrey, Stephen J [Los Alamos National Laboratory; Foley, Timothy J [Los Alamos National Laboratory; Son, Steven F [Los Alamos National Laboratory

2009-01-01

The advent of widely available nanoscale energetic composites has resulted in a flurry of novel applications. One of these applications is the use of nanomaterials in energetic compositions. In compositions that exhibit high sensitivity to stimulus, these materials are often termed metastable intermolecular composites (MIC). More generally, these compositions are simply called nanoenergetics. Researchers have used many different experimental techniques to analyze the various properties of nanoenergetic systems. Among these various techniques, the confined tube burn is a simple experiment that is capable of obtaining much data related to the combustion of these materials. The purpose of this report is to review the current state of the confined tube burn experiment, including the drawbacks of the technique and possible remedies. As this report is intended to focus on the specific experimental technique, data from many different energetic materials, and experimental configurations will be presented. The qualitative and quantitative data that can be gathered using confined tube burn experiments include burning rates, total impulse, pressure rise rate, and burning rate differences between different detector types. All of these measurements lend insight into the combustion properties and mechanisms of specific nanoenergetics. Finally, certain data indicates a more complicated flow scenario which may need to be considered when developing burn tube models.

Medical home capabilities of primary care practices that serve sociodemographically vulnerable neighborhoods.

Science.gov (United States)

Friedberg, Mark W; Coltin, Kathryn L; Safran, Dana Gelb; Dresser, Marguerite; Schneider, Eric C

2010-06-14

Under current medical home proposals, primary care practices using specific structural capabilities will receive enhanced payments. Some practices disproportionately serve sociodemographically vulnerable neighborhoods. If these practices lack medical home capabilities, their ineligibility for enhanced payments could worsen disparities in care. Via survey, 308 Massachusetts primary care practices reported their use of 13 structural capabilities commonly included in medical home proposals. Using geocoded US Census data, we constructed racial/ethnic minority and economic disadvantage indices to describe the neighborhood served by each practice. We compared the structural capabilities of "disproportionate-share" practices (those in the most sociodemographically vulnerable quintile on each index) and others. Racial/ethnic disproportionate-share practices were more likely than others to have staff assisting patient self-management (69% vs 55%; P = .003), on-site language interpreters (54% vs 26%; P primary care practices serving sociodemographically vulnerable neighborhoods were more likely than other practices to have structural capabilities commonly included in medical home proposals. Payments tied to these capabilities may aid practices serving vulnerable populations.

Experimental system design for the integration of trapped-ion and superconducting qubit systems

Science.gov (United States)

De Motte, D.; Grounds, A. R.; Rehák, M.; Rodriguez Blanco, A.; Lekitsch, B.; Giri, G. S.; Neilinger, P.; Oelsner, G.; Il'ichev, E.; Grajcar, M.; Hensinger, W. K.

2016-12-01

We present a design for the experimental integration of ion trapping and superconducting qubit systems as a step towards the realization of a quantum hybrid system. The scheme addresses two key difficulties in realizing such a system: a combined microfabricated ion trap and superconducting qubit architecture, and the experimental infrastructure to facilitate both technologies. Developing upon work by Kielpinski et al. (Phys Rev Lett 108(13):130504, 2012. doi: 10.1103/PhysRevLett.108.130504), we describe the design, simulation and fabrication process for a microfabricated ion trap capable of coupling an ion to a superconducting microwave LC circuit with a coupling strength in the tens of kHz. We also describe existing difficulties in combining the experimental infrastructure of an ion trapping set-up into a dilution refrigerator with superconducting qubits and present solutions that can be immediately implemented using current technology.

Comparison between phase-shift full-bridge converters with noncoupled and coupled current-doubler rectifier.

Science.gov (United States)

Tsai, Cheng-Tao; Su, Jye-Chau; Tseng, Sheng-Yu

2013-01-01

This paper presents comparison between phase-shift full-bridge converters with noncoupled and coupled current-doubler rectifier. In high current capability and high step-down voltage conversion, a phase-shift full-bridge converter with a conventional current-doubler rectifier has the common limitations of extremely low duty ratio and high component stresses. To overcome these limitations, a phase-shift full-bridge converter with a noncoupled current-doubler rectifier (NCDR) or a coupled current-doubler rectifier (CCDR) is, respectively, proposed and implemented. In this study, performance analysis and efficiency obtained from a 500 W phase-shift full-bridge converter with two improved current-doubler rectifiers are presented and compared. From their prototypes, experimental results have verified that the phase-shift full-bridge converter with NCDR has optimal duty ratio, lower component stresses, and output current ripple. In component count and efficiency comparison, CCDR has fewer components and higher efficiency at full load condition. For small size and high efficiency requirements, CCDR is relatively suitable for high step-down voltage and high efficiency applications.

Comparison between Phase-Shift Full-Bridge Converters with Noncoupled and Coupled Current-Doubler Rectifier

Directory of Open Access Journals (Sweden)

Cheng-Tao Tsai

2013-01-01

Full Text Available This paper presents comparison between phase-shift full-bridge converters with noncoupled and coupled current-doubler rectifier. In high current capability and high step-down voltage conversion, a phase-shift full-bridge converter with a conventional current-doubler rectifier has the common limitations of extremely low duty ratio and high component stresses. To overcome these limitations, a phase-shift full-bridge converter with a noncoupled current-doubler rectifier (NCDR or a coupled current-doubler rectifier (CCDR is, respectively, proposed and implemented. In this study, performance analysis and efficiency obtained from a 500 W phase-shift full-bridge converter with two improved current-doubler rectifiers are presented and compared. From their prototypes, experimental results have verified that the phase-shift full-bridge converter with NCDR has optimal duty ratio, lower component stresses, and output current ripple. In component count and efficiency comparison, CCDR has fewer components and higher efficiency at full load condition. For small size and high efficiency requirements, CCDR is relatively suitable for high step-down voltage and high efficiency applications.

Verification and validation of COBRA-SFS transient analysis capability

International Nuclear Information System (INIS)

Rector, D.R.; Michener, T.E.; Cuta, J.M.

1998-05-01

This report provides documentation of the verification and validation testing of the transient capability in the COBRA-SFS code, and is organized into three main sections. The primary documentation of the code was published in September 1995, with the release of COBRA-SFS, Cycle 2. The validation and verification supporting the release and licensing of COBRA-SFS was based solely on steady-state applications, even though the appropriate transient terms have been included in the conservation equations from the first cycle. Section 2.0, COBRA-SFS Code Description, presents a capsule description of the code, and a summary of the conservation equations solved to obtain the flow and temperature fields within a cask or assembly model. This section repeats in abbreviated form the code description presented in the primary documentation (Michener et al. 1995), and is meant to serve as a quick reference, rather than independent documentation of all code features and capabilities. Section 3.0, Transient Capability Verification, presents a set of comparisons between code calculations and analytical solutions for selected heat transfer and fluid flow problems. Section 4.0, Transient Capability Validation, presents comparisons between code calculations and experimental data obtained in spent fuel storage cask tests. Based on the comparisons presented in Sections 2.0 and 3.0, conclusions and recommendations for application of COBRA-SFS to transient analysis are presented in Section 5.0

Critical operations capabilities in a high cost environment: a multiple case study

Science.gov (United States)

Sansone, C.; Hilletofth, P.; Eriksson, D.

2018-04-01

Operations capabilities have been a popular research area for many years and several frameworks have been proposed in the literature. The current frameworks do not take specific contexts into consideration, for instance a high cost environment. This research gap is of particular interest since a manufacturing relocation process has been ongoing the last decades, leading to a huge amount of manufacturing being moved from high to low cost environments. The purpose of this study is to identify critical operations capabilities in a high cost environment. The two research questions were: What are the critical operations capabilities dimensions in a high cost environment? What are the critical operations capabilities in a high cost environment? A multiple case study was conducted and three Swedish manufacturing firms were selected. The study was based on the investigation of an existing framework of operations capabilities. The main dimensions of operations capabilities included in the framework were: cost, quality, delivery, flexibility, service, innovation and environment. Each of the dimensions included two or more operations capabilities. The findings confirmed the validity of the framework and its usefulness in a high cost environment and a new operations capability was revealed (employee flexibility).

Heavy Lift Launch Capability with a New Hydrocarbon Engine

Science.gov (United States)

Threet, Grady E., Jr.; Holt, James B.; Philips, Alan D.; Garcia, Jessica A.

2011-01-01

The Advanced Concepts Office at NASA's George C. Marshall Space Flight Center was tasked to define the thrust requirement of a new liquid oxygen rich staged combustion cycle hydrocarbon engine that could be utilized in a launch vehicle to meet NASA s future heavy lift needs. Launch vehicle concepts were sized using this engine for different heavy lift payload classes. Engine out capabilities for one of the heavy lift configurations were also analyzed for increased reliability that may be desired for high value payloads or crewed missions. The applicability for this engine in vehicle concepts to meet military and commercial class payloads comparable to current ELV capability was also evaluated.

Controlling Fringe Sensitivity of Electro-Optic Holography Systems Using Laser Diode Current Modulation

Science.gov (United States)

Bybee, Shannon J.

2001-01-01

Electro-Optic Holography (EOH) is a non-intrusive, laser-based, displacement measurement technique capable of static and dynamic displacement measurements. EOH is an optical interference technique in which fringe patterns that represent displacement contour maps are generated. At excessively large displacements the fringe density may be so great that individual fringes are not resolvable using typical EOH techniques. This thesis focuses on the development and implementation of a method for controlling the sensitivity of the EOH system. This method is known as Frequency Translated Electro-Optic Holography (FTEOH). It was determined that by modulating the current source of the laser diode at integer multiples of the object vibration, the fringe pattern is governed by higher order Bessel function of the first kind and the number of fringes that represent a given displacement can be controlled. The reduction of fringes is theoretically unlimited but physically limited by the frequency bandwidth of the signal generator, providing modulation to the laser diode. Although this research technique has been verified theoretically and experimentally in this thesis, due to the current laser diode capabilities it is a tedious and time consuming process to acquire data using the FTEOH technique.

Process for Upgrading Cognitive Assessment Capabilities Onboard the International Space Station

Science.gov (United States)

Picano, J. J.; Seaton, K. A.; Holland, A. W.

2016-01-01

MOTIVATION: Spaceflight poses varied and unique risks to the brain and cognitive functioning including radiation exposure, sleep disturbance, fatigue, fluid shifts (increased intracranial pressure), toxin exposure, elevated carbon dioxide, and traumatic brain injury, among others. These potential threats to cognitive functioning are capable of degrading performance and compromising mission success. Furthermore, the threats may increase in severity, and new types of threats may emerge for longer duration exploration missions. This presentation will describe the process used to identify gaps in our current approach, evaluate best practices in cognitive assessment, and transition new cognitive assessment tools to operational use. OVERVIEW: Risks to brain health and performance posed by spaceflight missions require sensitive tools to assess cognitive functioning of astronauts in flight. The Spaceflight Cognitive Assessment Tool for Windows (WinSCAT) is the automated cognitive assessment tool currently deployed onboard the International Space Station (ISS). WinSCAT provides astronauts and flight surgeons with objective data to monitor neurocognitive functioning. WinSCAT assesses 5 discrete cognitive domains, is sensitive to changes in cognitive functioning, and was designed to be completed in less than 15 minutes. However, WinSCAT does not probe other areas of cognitive functioning that might be important to mission success. Researchers recently have developed batteries that may expand current capabilities, such as increased sensitivity to subtle fluctuations in cognitive functioning. Therefore, we engaged in a systematic process review in order to improve upon our current capabilities and incorporate new advances in cognitive assessment. This process included a literature review on newer measures of neurocognitive assessment, surveys of operational flight surgeons at NASA regarding needs and gaps in our capabilities, and expert panel review of candidate cognitive

Buck-Boost Current-Source Inverters With Diode-Inductor Network

DEFF Research Database (Denmark)

Gao, Feng; Liang, Chao; Loh, Poh Chiang

2009-01-01

This paper presents a number of novel currentsource inverters (CSIs) with enhanced current buck-boost capability. By adding a unique diode-inductor network between the inverter circuitry and current-boost elements, the proposed buck-boost CSIs demonstrate a doubling of current-boost capability......, as compared with other recently reported buck-boost CSIs. For controlling the proposed CSIs, two modulation schemes are designed for achieving either optimized harmonic performance or minimized commutation count without influencing the inverter current buck-boost gain. These theoretical findings were...

Capability-based computer systems

CERN Document Server

Levy, Henry M

2014-01-01

Capability-Based Computer Systems focuses on computer programs and their capabilities. The text first elaborates capability- and object-based system concepts, including capability-based systems, object-based approach, and summary. The book then describes early descriptor architectures and explains the Burroughs B5000, Rice University Computer, and Basic Language Machine. The text also focuses on early capability architectures. Dennis and Van Horn's Supervisor; CAL-TSS System; MIT PDP-1 Timesharing System; and Chicago Magic Number Machine are discussed. The book then describes Plessey System 25

ROV: improving remotely operated vehicle (ROV) intervention capabilities for blowout preventer override systems

Energy Technology Data Exchange (ETDEWEB)

Lazar, Stephen [Christopher S. Mancini, Tomball, TX (United States)

2012-07-01

Events during 2010 have focused attention on increased ROV/BOP Intervention capabilities and standardization of BOP/ROV interfaces in the oil and gas offshore industry. Currently no enforced set standards for ROV intervention panels or manifold types for use on BOP Override systems are specified. The industry offers multiple configurations at present. This abstract will discuss the advantages and disadvantages of the various configurations in existence, trending toward suggested industry standards taking shape as requirements in the near term. Standards for the offshore industry or a set specification must be made to increase safety and functionality of BOP control systems. To date, ROV override capabilities have been added to existing engineered BOP systems. BOP designed closing times were not a critical consideration, only that the access was there to allow for ROV override. Increased ROV flow and pressure capabilities: no current minimum flow requirements for Emergency BOP Override pumps are established. Based on stack valving and configuration, a minimum, 7 gpm may be required to shift valving fully to allow BOP operator function. IADC/API minimum requirements may be proposed at 10 gpm at 3000psi. Based on shear pressures exceeding 3000psi, pressures of 5000psi should be considered. Current intervention skids/pump capabilities will be required if ROVs must achieve API 16D BOP minimum closing times. Remote or isolated accumulation for increased intervention capabilities offers possibilities when ANY ROV of opportunity can trigger a function (such as small inspection type ROVs). Increased volumes will be required. This is critical in functioning stack rams with an ROV of opportunity to achieve API 16D closing times. We now understand that higher flows and pressures are required along with standardization of stab types. Current recommendations: API 17H Hi-Flow manifolds should be added to essential ROV overrides. ROV skids will have a minimum requirement of 10gpm

Strength capability while kneeling.

Science.gov (United States)

Haslegrave, C M; Tracy, M F; Corlett, E N

1997-12-01

Work sometimes has to be carried out kneeling, particularly where jobs are performed in confined spaces as is common for miners, aircraft baggage handlers and maintenance workers. In order to assess the risks in performing forceful tasks under such conditions, data is needed on strength capabilities of kneeling subjects. A study was undertaken to measure isometric strength in single-handed exertions for male subjects and to investigate the effects on this of task layout factors (direction of force exertion, reach distance, height of the workpiece and orientation relative to the subject's sagittal plane). The data has been tabulated to show the degree to which strength may be reduced in different situations and analysis of the task factors showed their influence to be complex with direction of exertion and reach distance having the greatest effect. The results also suggest that exertions are weaker when subjects are kneeling on two knees than when kneeling on one knee, although this needs to be confirmed by direct experimental comparison.

Semi-empirical master curve concept describing the rate capability of lithium insertion electrodes

Science.gov (United States)

Heubner, C.; Seeba, J.; Liebmann, T.; Nickol, A.; Börner, S.; Fritsch, M.; Nikolowski, K.; Wolter, M.; Schneider, M.; Michaelis, A.

2018-03-01

A simple semi-empirical master curve concept, describing the rate capability of porous insertion electrodes for lithium-ion batteries, is proposed. The model is based on the evaluation of the time constants of lithium diffusion in the liquid electrolyte and the solid active material. This theoretical approach is successfully verified by comprehensive experimental investigations of the rate capability of a large number of porous insertion electrodes with various active materials and design parameters. It turns out, that the rate capability of all investigated electrodes follows a simple master curve governed by the time constant of the rate limiting process. We demonstrate that the master curve concept can be used to determine optimum design criteria meeting specific requirements in terms of maximum gravimetric capacity for a desired rate capability. The model further reveals practical limits of the electrode design, attesting the empirically well-known and inevitable tradeoff between energy and power density.

Mobile Test Capabilities

Data.gov (United States)

Federal Laboratory Consortium — The Electrical Power Mobile Test capabilities are utilized to conduct electrical power quality testing on aircraft and helicopters. This capability allows that the...

A new pneumatic suspension system with independent stiffness and ride height tuning capabilities

Science.gov (United States)

Yin, Zhihong; Khajepour, Amir; Cao, Dongpu; Ebrahimi, Babak; Guo, Konghui

2012-12-01

This paper introduces a new pneumatic spring for vehicle suspension systems, allowing independent tuning of stiffness and ride height according to different vehicle operating conditions and driver preferences. The proposed pneumatic spring comprises a double-acting pneumatic cylinder, two accumulators and a tuning subsystem. This paper presents a detailed description of the pneumatic spring and its working principle. The mathematical model is established based on principles of thermo and fluid dynamics. An experimental setup has been designed and fabricated for testing and evaluating the proposed pneumatic spring. The analytical and experimental results confirm the capability of the new pneumatic spring system for independent tuning of stiffness and ride height. The mathematical model is verified and the capabilities of the pneumatic spring are further proved. It is concluded that this new pneumatic spring provides a more flexible suspension design alternative for meeting various conflicting suspension requirements for ride comfort and performance.

Experimental study on magnetically insulated transmission line electrode surface evolution process under MA/cm current density

Energy Technology Data Exchange (ETDEWEB)

Zhang, PengFei; Qiu, Aici [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); State Key Laboratory of Intense Pulse Radiation of Simulation and Effect, Northwest Institute of Nuclear Technology, Xi' an 710024 (China); Hu, Yang; Yang, HaiLiang; Sun, Jiang; Wang, Liangping; Cong, Peitian [State Key Laboratory of Intense Pulse Radiation of Simulation and Effect, Northwest Institute of Nuclear Technology, Xi' an 710024 (China)

2016-03-15

The design of high-current density magnetically insulated transmission line (MITL) is a difficult problem of current large-scale Z-pinch device. In particular, a thorough understanding of the MITL electrode surface evolution process under high current density is lacking. On the “QiangGuang-I” accelerator, the load area possesses a low inductance short-circuit structure with a diameter of 2.85 mm at the cathode, and three reflux columns with a diameter of 3 mm and uniformly distributed circumference at the anode. The length of the high density MITL area is 20 mm. A laser interferometer is used to assess and analyze the state of the MITL cathode and anode gap, and their evolution process under high current density. Experimental results indicate that evident current loss is not observed in the current density area at pulse leading edge, and peak when the surface current density reaches MA/cm. Analysis on electrode surface working conditions indicates that when the current leading edge is at 71.5% of the peak, the total evaporation of MITL cathode structure can be realized by energy deposition caused by ohmic heating. The electrode state changes, and diffusion conditions are reflected in the laser interferometer image. The MITL cathode area mainly exists in metal vapor form. The metal vapor density in the cathode central region is higher than the upper limit of laser penetration density (∼4 × 10{sup 21}/cm{sup 3}), with an expansion velocity of ∼0.96 km/s. The metal vapor density in the electrode outer area may lead to evident distortion of fringes, and its expansion velocity is faster than that in the center area (1.53 km/s).

Experimental Irradiations of Materials and Fuels in the BR2 Reactor: An Overview of Current Programmes

International Nuclear Information System (INIS)

Van Dyck, S.; Koonen, E.; Verwerft, M.; Wéber, M.

2013-01-01

The BR2 material test reactor offers a variety of experimental irradiation possibilities for testing of materials, fuels and instruments. The current paper gives an overview of the recent and ongoing programmes in order to illustrate the experimental potential of the reactor. Three domains of applications are reviewed: Irradiation of materials and fuels for pressurised water reactors (PWR); irradiation of materials for accelerator driven systems (ADS), cooled by liquid lead alloys; and irradiation of fuel for Material Test Reactors (MTR). For PWR relevant tests, a dedicated loop is available, providing a full simulation of the thermo hydraulic conditions of a PWR. ADS related tests require particular control of the irradiation environment and the necessary safety precautions in order to avoid 210 Po contamination. In-core mechanical testing of materials is done in comparison and complimentarily to post-irradiation examinations in order to assess flux related effects on the deformation behaviour of materials. (author)

Study on evaluation of containment capability of glove box under fire accident (2)

International Nuclear Information System (INIS)

Abe, Hitoshi; Watanabe, Koji; Tashiro, Shinsuke; Uchiyama, Gunzo

2007-11-01

In the MOX fuel fabrication facility, MOX is required to be handled in glove box to sustain containment of MOX into the facility. In case of fire in the facility, the containment capability of glove box may be deteriorated by pyrolysis or combustion of the plastic materials as components of glove box caused by thermal stress from flame. The purpose of this study is to examine pyrolysis and combustion properties of the materials for applying them to quantitative evaluation method for the containment capability of glove box under fire. This report summarize experimental results about the properties under the air condition and investigation of evaluation model for estimating time-course of deteriorating containment capability of glove box under fire. (author)

Addition of liquid waste incineration capability to the INEL's low-level waste incinerator

International Nuclear Information System (INIS)

Steverson, E.M.; Clark, D.P.; McFee, J.N.

1986-01-01

A liquid waste system has recently been installed in the Waste Experimental Reduction Facility (WERF) incinerator at the Idaho National Engineering Laboratory (INEL). In this paper, aspects of the incineration system such as the components, operations, capabilities, capital cost, EPA permit requirements, and future plans are discussed. The principal objective of the liquid incineration system is to provide the capability to process hazardous, radioactively contaminated, non-halogenated liquid wastes. The system consists primarily of a waste feed system, instrumentation and controls, and a liquid burner, which were procured at a capital cost of $115,000

Maintaining operational excellence: building capability beyond knowledge transfer

International Nuclear Information System (INIS)

Ramjist, S.

2013-01-01

This paper describes the issues relating to human resources and maintaining capabilities in an organization. The sustaining elements are: vision and plan for excellence; invest in the plant; invest in human capital; find and fix problems. There is much discussion about knowledge transfer and retention that is mainly focused on technical attributes and proficiency. We are losing more people with the requisite managerial and leadership capability than we can develop and backfill at a Time when our industry is facing increased competition and decreased margins. We are vulnerable because this Increases our dependence on augmented staff for certain key leadership roles. Previous methods for developing people will take too long and does not appeal to current generation. A solution, not the only solution, but the one we have chosen is initial hiring of operators, maintainers and engineers, internal promotion for key roles (FLM, FSOS, Shift Supervisor, Section Manager, ANO) and focus on all three aspects of capability and looking for leadership traits. Look for ambition, drive, initiative and motivation. Identify, separate and stream. Take specific measures to accelerate growth.

Maintaining operational excellence: building capability beyond knowledge transfer

Energy Technology Data Exchange (ETDEWEB)

Ramjist, S. [Ontario Power Generation, Darlington Nuclear Generating Station, Bowmanville, Ontario (Canada)

2013-07-01

This paper describes the issues relating to human resources and maintaining capabilities in an organization. The sustaining elements are: vision and plan for excellence; invest in the plant; invest in human capital; find and fix problems. There is much discussion about knowledge transfer and retention that is mainly focused on technical attributes and proficiency. We are losing more people with the requisite managerial and leadership capability than we can develop and backfill at a Time when our industry is facing increased competition and decreased margins. We are vulnerable because this Increases our dependence on augmented staff for certain key leadership roles. Previous methods for developing people will take too long and does not appeal to current generation. A solution, not the only solution, but the one we have chosen is initial hiring of operators, maintainers and engineers, internal promotion for key roles (FLM, FSOS, Shift Supervisor, Section Manager, ANO) and focus on all three aspects of capability and looking for leadership traits. Look for ambition, drive, initiative and motivation. Identify, separate and stream. Take specific measures to accelerate growth.

A Web Service Protocol Realizing Interoperable Internet of Things Tasking Capability

Science.gov (United States)

Huang, Chih-Yuan; Wu, Cheng-Hung

2016-01-01

The Internet of Things (IoT) is an infrastructure that interconnects uniquely-identifiable devices using the Internet. By interconnecting everyday appliances, various monitoring, and physical mashup applications can be constructed to improve human’s daily life. In general, IoT devices provide two main capabilities: sensing and tasking capabilities. While the sensing capability is similar to the World-Wide Sensor Web, this research focuses on the tasking capability. However, currently, IoT devices created by different manufacturers follow different proprietary protocols and are locked in many closed ecosystems. This heterogeneity issue impedes the interconnection between IoT devices and damages the potential of the IoT. To address this issue, this research aims at proposing an interoperable solution called tasking capability description that allows users to control different IoT devices using a uniform web service interface. This paper demonstrates the contribution of the proposed solution by interconnecting different IoT devices for different applications. In addition, the proposed solution is integrated with the OGC SensorThings API standard, which is a Web service standard defined for the IoT sensing capability. Consequently, the Extended SensorThings API can realize both IoT sensing and tasking capabilities in an integrated and interoperable manner. PMID:27589759

A Web Service Protocol Realizing Interoperable Internet of Things Tasking Capability.

Science.gov (United States)

Huang, Chih-Yuan; Wu, Cheng-Hung

2016-08-31

The Internet of Things (IoT) is an infrastructure that interconnects uniquely-identifiable devices using the Internet. By interconnecting everyday appliances, various monitoring, and physical mashup applications can be constructed to improve human's daily life. In general, IoT devices provide two main capabilities: sensing and tasking capabilities. While the sensing capability is similar to the World-Wide Sensor Web, this research focuses on the tasking capability. However, currently, IoT devices created by different manufacturers follow different proprietary protocols and are locked in many closed ecosystems. This heterogeneity issue impedes the interconnection between IoT devices and damages the potential of the IoT. To address this issue, this research aims at proposing an interoperable solution called tasking capability description that allows users to control different IoT devices using a uniform web service interface. This paper demonstrates the contribution of the proposed solution by interconnecting different IoT devices for different applications. In addition, the proposed solution is integrated with the OGC SensorThings API standard, which is a Web service standard defined for the IoT sensing capability. Consequently, the Extended SensorThings API can realize both IoT sensing and tasking capabilities in an integrated and interoperable manner.

Building Service Provider Capabilities

DEFF Research Database (Denmark)

Brandl, Kristin; Jaura, Manya; Ørberg Jensen, Peter D.

2015-01-01

In this paper we study whether and how the interaction between clients and the service providers contributes to the development of capabilities in service provider firms. In situations where such a contribution occurs, we analyze how different types of activities in the production process...... process. We find that clients influence the development of human capital capabilities and management capabilities in reciprocally produced services. While in sequential produced services clients influence the development of organizational capital capabilities and management capital capabilities....... of the services, such as sequential or reciprocal task activities, influence the development of different types of capabilities. We study five cases of offshore-outsourced knowledge-intensive business services that are distinguished according to their reciprocal or sequential task activities in their production...

Dynamic capabilities for cooperation in Brazilian multinational and factors determining its management

Directory of Open Access Journals (Sweden)

Priscila Rezende da Costa

2015-05-01

Full Text Available In the context of emerging companies’ growth, current challenges depend on the local generation of product and process innovations, as well as dynamic capability to generate innovative solutions cooperatively and new globe business models. The objective of this study is to analyse the determining managerial factors for the dynamic capability of cooperation in Brazilian multinationals (BMNs. A survey was conducted with a sample of 60 BMNs, and a structured questionnaire and statistical tests with factorial analysis and Cronbach's alpha were used. The aggregate analysis of the results indicates that BMNs are going through a transitional process between the operational capability of cooperation and the capability for dynamic cooperation, which are relevant to the continuous adaptation of already-established cooperative management routines and the evaluation and incorporation of the relational capability of management practices that consider systemic flows, open innovation and integrate strategic intentionality into cooperative processes.

Radiation induced currents in mineral-insulated cables and in pick-up coils: model calculations and experimental verification in the BR1 reactor

Science.gov (United States)

Vermeeren, Ludo; Leysen, Willem; Brichard, Benoit

2018-01-01

Mineral-insulated (MI) cables and Low-Temperature Co-fired Ceramic (LTCC) magnetic pick-up coils are intended to be installed in various position in ITER. The severe ITER nuclear radiation field is expected to lead to induced currents that could perturb diagnostic measurements. In order to assess this problem and to find mitigation strategies models were developed for the calculation of neutron-and gamma-induced currents in MI cables and in LTCC coils. The models are based on calculations with the MCNPX code, combined with a dedicated model for the drift of electrons stopped in the insulator. The gamma induced currents can be easily calculated with a single coupled photon-electron MCNPX calculation. The prompt neutron induced currents requires only a single coupled neutron-photon-electron MCNPX run. The various delayed neutron contributions require a careful analysis of all possibly relevant neutron-induced reaction paths and a combination of different types of MCNPX calculations. The models were applied for a specific twin-core copper MI cable, for one quad-core copper cable and for silver conductor LTCC coils (one with silver ground plates in order to reduce the currents and one without such silver ground plates). Calculations were performed for irradiation conditions (neutron and gamma spectra and fluxes) in relevant positions in ITER and in the Y3 irradiation channel of the BR1 reactor at SCK•CEN, in which an irradiation test of these four test devices was carried out afterwards. We will present the basic elements of the models and show the results of all relevant partial currents (gamma and neutron induced, prompt and various delayed currents) in BR1-Y3 conditions. Experimental data will be shown and analysed in terms of the respective contributions. The tests were performed at reactor powers of 350 kW and 1 MW, leading to thermal neutron fluxes of 1E11 n/cm2s and 3E11 n/cm2s, respectively. The corresponding total radiation induced currents are ranging from

Size and transportation capabilities of the existing U.S. cask fleet

International Nuclear Information System (INIS)

Danese, F.L.; Johnson, P.E.; Joy, D.S.

1990-01-01

This paper investigates the current spent nuclear fuel cask fleet capability in the United States. It assesses the degree to which the current fleet would be available, as a contingency, until proposed Office of Civilian Radioactive Waste Management casks become operational. A limited fleet of ten spent fuel transportation casks is found to be readily available for use in Federal waste management efforts over the next decade

Capabilities of current wildfire models when simulating topographical flow

Science.gov (United States)

Kochanski, A.; Jenkins, M.; Krueger, S. K.; McDermott, R.; Mell, W.

2009-12-01

Accurate predictions of the growth, spread and suppression of wild fires rely heavily on the correct prediction of the local wind conditions and the interactions between the fire and the local ambient airflow. Resolving local flows, often strongly affected by topographical features like hills, canyons and ridges, is a prerequisite for accurate simulation and prediction of fire behaviors. In this study, we present the results of high-resolution numerical simulations of the flow over a smooth hill, performed using (1) the NIST WFDS (WUI or Wildland-Urban-Interface version of the FDS or Fire Dynamic Simulator), and (2) the LES version of the NCAR Weather Research and Forecasting (WRF-LES) model. The WFDS model is in the initial stages of development for application to wind flow and fire spread over complex terrain. The focus of the talk is to assess how well simple topographical flow is represented by WRF-LES and the current version of WFDS. If sufficient progress has been made prior to the meeting then the importance of the discrepancies between the predicted and measured winds, in terms of simulated fire behavior, will be examined.

Assessment of predictive capabilities for aerodynamic heating in hypersonic flow

Science.gov (United States)

Knight, Doyle; Chazot, Olivier; Austin, Joanna; Badr, Mohammad Ali; Candler, Graham; Celik, Bayram; Rosa, Donato de; Donelli, Raffaele; Komives, Jeffrey; Lani, Andrea; Levin, Deborah; Nompelis, Ioannis; Panesi, Marco; Pezzella, Giuseppe; Reimann, Bodo; Tumuklu, Ozgur; Yuceil, Kemal

2017-04-01

The capability for CFD prediction of hypersonic shock wave laminar boundary layer interaction was assessed for a double wedge model at Mach 7.1 in air and nitrogen at 2.1 MJ/kg and 8 MJ/kg. Simulations were performed by seven research organizations encompassing both Navier-Stokes and Direct Simulation Monte Carlo (DSMC) methods as part of the NATO STO AVT Task Group 205 activity. Comparison of the CFD simulations with experimental heat transfer and schlieren visualization suggest the need for accurate modeling of the tunnel startup process in short-duration hypersonic test facilities, and the importance of fully 3-D simulations of nominally 2-D (i.e., non-axisymmmetric) experimental geometries.

Imaging capabilities of germanium gamma cameras

International Nuclear Information System (INIS)

Steidley, J.W.

1977-01-01

Quantitative methods of analysis based on the use of a computer simulation were developed and used to investigate the imaging capabilities of germanium gamma cameras. The main advantage of the computer simulation is that the inherent unknowns of clinical imaging procedures are removed from the investigation. The effects of patient scattered radiation were incorporated using a mathematical LSF model which was empirically developed and experimentally verified. Image modifying effects of patient motion, spatial distortions, and count rate capabilities were also included in the model. Spatial domain and frequency domain modeling techniques were developed and used in the simulation as required. The imaging capabilities of gamma cameras were assessed using low contrast lesion source distributions. The results showed that an improvement in energy resolution from 10% to 2% offers significant clinical advantages in terms of improved contrast, increased detectability, and reduced patient dose. The improvements are of greatest significance for small lesions at low contrast. The results of the computer simulation were also used to compare a design of a hypothetical germanium gamma camera with a state-of-the-art scintillation camera. The computer model performed a parametric analysis of the interrelated effects of inherent and technological limitations of gamma camera imaging. In particular, the trade-off between collimator resolution and collimator efficiency for detection of a given low contrast lesion was directly addressed. This trade-off is an inherent limitation of both gamma cameras. The image degrading effects of patient motion, camera spatial distortions, and low count rate were shown to modify the improvements due to better energy resolution. Thus, based on this research, the continued development of germanium cameras to the point of clinical demonstration is recommended

Experimental integration of quantum key distribution and gigabit-capable passive optical network

Science.gov (United States)

Sun, Wei; Wang, Liu-Jun; Sun, Xiang-Xiang; Mao, Yingqiu; Yin, Hua-Lei; Wang, Bi-Xiao; Chen, Teng-Yun; Pan, Jian-Wei

2018-01-01

Quantum key distribution (QKD) ensures information-theoretic security for the distribution of random bits between two remote parties. To extend QKD applications to fiber-to-the-home optical communications, such as gigabit-capable passive optical networks (GPONs), an effective method is the use of wavelength-division multiplexing. However, the Raman scattering noise from intensive classical traffic and the huge loss introduced by the beam splitter in a GPON severely limits the performance of QKD. Here, we demonstrate the integration of QKD and a commercial GPON system with fiber lengths up to 14 km, in which the maximum splitting ratio of the beam splitter reaches 1:64. By placing the QKD transmitter on the optical line terminal side, we reduce the Raman noise collected at the QKD receiver. Using a bypass structure, the loss of the beam splitter is circumvented effectively. Our results pave the way to extending the applications of QKD to last-mile communications.

Numerical and experimental investigations of human swimming motions.

Science.gov (United States)

Takagi, Hideki; Nakashima, Motomu; Sato, Yohei; Matsuuchi, Kazuo; Sanders, Ross H

2016-08-01

This paper reviews unsteady flow conditions in human swimming and identifies the limitations and future potential of the current methods of analysing unsteady flow. The capability of computational fluid dynamics (CFD) has been extended from approaches assuming steady-state conditions to consideration of unsteady/transient conditions associated with the body motion of a swimmer. However, to predict hydrodynamic forces and the swimmer's potential speeds accurately, more robust and efficient numerical methods are necessary, coupled with validation procedures, requiring detailed experimental data reflecting local flow. Experimental data obtained by particle image velocimetry (PIV) in this area are limited, because at present observations are restricted to a two-dimensional 1.0 m(2) area, though this could be improved if the output range of the associated laser sheet increased. Simulations of human swimming are expected to improve competitive swimming, and our review has identified two important advances relating to understanding the flow conditions affecting performance in front crawl swimming: one is a mechanism for generating unsteady fluid forces, and the other is a theory relating to increased speed and efficiency.

Photoionization capable, extreme and vacuum ultraviolet emission in developing low temperature plasmas in air

NARCIS (Netherlands)

Stephens, J.; Fierro, A.; Beeson, S.; Laity, G.; Trienekens, D.; Joshi, R.P.; Dickens, J.; Neuber, A.

2016-01-01

Experimental observation of photoionization capable extreme ultraviolet and vacuum ultraviolet emission from nanosecond timescale, developing low temperature plasmas (i.e. streamer discharges) in atmospheric air is presented. Applying short high voltage pulses enabled the observation of the onset of

Marshall Space Flight Center's Impact Testing Facility Capabilities

Science.gov (United States)

Finchum, Andy; Hubbs, Whitney; Evans, Steve

2008-01-01

Marshall Space Flight Center s (MSFC) Impact Testing Facility (ITF) serves as an important installation for space and missile related materials science research. The ITF was established and began its research in spacecraft debris shielding in the early 1960s, then played a major role in the International Space Station debris shield development. As NASA became more interested in launch debris and in-flight impact concerns, the ITF grew to include research in a variety of impact genres. Collaborative partnerships with the DoD led to a wider range of impact capabilities being relocated to MSFC as a result of the closure of Particle Impact Facilities in Santa Barbara, California. The Particle Impact Facility had a 30 year history in providing evaluations of aerospace materials and components during flights through rain, ice, and solid particle environments at subsonic through hypersonic velocities. The facility s unique capabilities were deemed a "National Asset" by the DoD. The ITF now has capabilities including environmental, ballistic, and hypervelocity impact testing utilizing an array of air, powder, and two-stage light gas guns to accommodate a variety of projectile and target types and sizes. Numerous upgrades including new instrumentation, triggering circuitry, high speed photography, and optimized sabot designs have been implemented. Other recent research has included rain drop demise characterization tests to obtain data for inclusion in on-going model development. The current and proposed ITF capabilities range from rain to micrometeoroids allowing the widest test parameter range possible for materials investigations in support of space, atmospheric, and ground environments. These test capabilities including hydrometeor, single/multi-particle, ballistic gas guns, exploding wire gun, and light gas guns combined with Smooth Particle Hydrodynamics Code (SPHC) simulations represent the widest range of impact test capabilities in the country.

Satellite-based Tropical Cyclone Monitoring Capabilities

Science.gov (United States)

Hawkins, J.; Richardson, K.; Surratt, M.; Yang, S.; Lee, T. F.; Sampson, C. R.; Solbrig, J.; Kuciauskas, A. P.; Miller, S. D.; Kent, J.

2012-12-01

Satellite remote sensing capabilities to monitor tropical cyclone (TC) location, structure, and intensity have evolved by utilizing a combination of operational and research and development (R&D) sensors. The microwave imagers from the operational Defense Meteorological Satellite Program [Special Sensor Microwave/Imager (SSM/I) and the Special Sensor Microwave Imager Sounder (SSMIS)] form the "base" for structure observations due to their ability to view through upper-level clouds, modest size swaths and ability to capture most storm structure features. The NASA TRMM microwave imager and precipitation radar continue their 15+ yearlong missions in serving the TC warning and research communities. The cessation of NASA's QuikSCAT satellite after more than a decade of service is sorely missed, but India's OceanSat-2 scatterometer is now providing crucial ocean surface wind vectors in addition to the Navy's WindSat ocean surface wind vector retrievals. Another Advanced Scatterometer (ASCAT) onboard EUMETSAT's MetOp-2 satellite is slated for launch soon. Passive microwave imagery has received a much needed boost with the launch of the French/Indian Megha Tropiques imager in September 2011, basically greatly supplementing the very successful NASA TRMM pathfinder with a larger swath and more frequent temporal sampling. While initial data issues have delayed data utilization, current news indicates this data will be available in 2013. Future NASA Global Precipitation Mission (GPM) sensors starting in 2014 will provide enhanced capabilities. Also, the inclusion of the new microwave sounder data from the NPP ATMS (Oct 2011) will assist in mapping TC convective structures. The National Polar orbiting Partnership (NPP) program's VIIRS sensor includes a day night band (DNB) with the capability to view TC cloud structure at night when sufficient lunar illumination exits. Examples highlighting this new capability will be discussed in concert with additional data fusion efforts.

Building EOS capability for Malaysia - the options

Science.gov (United States)

Subari, M. D.; Hassan, A.

2014-06-01

Earth observation satellite (EOS) is currently a major tool to monitor earth dynamics and increase human understanding of earth surface process. Since the early 80s, Malaysia has been using EOS images for various applications, such as weather forecasting, land use mapping, agriculture, environment monitoring and others. Until now, all EOS images were obtained from foreign satellite systems. Realising on the strategic need of having its own capability, Malaysia embarked into EOS development programs in the early 90s. Starting with TiungSAT-1, a micro-satellite carrying small camera, then followed by RazakSAT, a small satellite carrying 2.5 m panchromatic (PAN) medium-aperture-camera, the current satellite program development, the RazakSAT-2, designed to carry a 1.0 m high resolution PAN and 4.0m multi-spectral camera, would become a strategic initiative of the government in developing and accelerating the nation's capability in the area of satellite technology and its application. Would this effort continue until all needs of the remote sensing community being fulfilled by its own EOS? This paper will analyze the intention of the Malaysian government through its National Space Policy and other related policy documents, and proposes some policy options on this. Key factors to be considered are specific data need of the EOS community, data availability and the more subjective political motivations such as national pride.

Evaluation of Current Planetary Boundary Layer Retrieval Capabilities from Space

Science.gov (United States)

Santanello, Joseph A., Jr.; Schaefer, Alexander J.; Blaisdell, John; Yorks, John

2016-01-01

The PBL over land remains a significant gap in our water and energy cycle understanding from space. This work combines unique NASA satellite and model products to demonstrate the ability of current sensors (advanced IR sounding and lidar) to retrieve PBL properties and in turn their potential to be used globally to evaluate and improve weather and climate prediction models. While incremental progress has been made in recent AIRS retrieval versions, insufficient vertical resolution remains in terms of detecting PBL properties. Lidar shows promise in terms of detecting vertical gradients (and PBLh) in the lower troposphere, but daytime conditions over land remain a challenge due to noise, and their coverage is limited to approximately 2 weeks or longer return times.

Experimental investigation of focusing and transport of heavy-current electron beams

International Nuclear Information System (INIS)

Baranchikov, E.I.; Gordeev, A.V.; Koba, Yu.V.; Korolev, V.D.; Pen'kina, V.S.; Rudakov, L.I.; Smirnov, V.P.; Sukhov, A.D.; Tarumov, E.Z.

The results of an experimental and theoretical study of beam transfer through transverse magnetic fields are outlined. The injection and transport of an annular relativistic electron beam due to a magnetic trap of acute-angle geometry are experimentally studied

Fast wave current drive on DIII-D

International Nuclear Information System (INIS)

deGrassie, J.S.; Petty, C.C.; Pinsker, R.I.

1995-01-01

The physics of electron heating and current drive with the fast magnetosonic wave has been demonstrated on DIII-D, in reasonable agreement with theoretical modeling. A recently completed upgrade to the fast wave capability should allow full noninductive current drive in steady state advanced confinement discharges and provide some current density profile control for the Advanced Tokamak Program. DIII-D now has three four-strap fast wave antennas and three transmitters, each with nominally 2 MW of generator power. Extensive experiments have been conducted with the first system, at 60 MHz, while the two newer systems have come into operation within the past year. The newer systems are configured for 60 to 120 MHz. The measured FWCD efficiency is found to increase linearly with electron temperature as γ = 0.4 x 10 18 T eo (keV) [A/m 2 W], measured up to central electron temperature over 5 keV. A newly developed technique for determining the internal noninductive current density profile gives efficiencies in agreement with this scaling and profiles consistent with theoretical predictions. Full noninductive current drive at 170 kA was achieved in a discharge prepared by rampdown of the Ohmic current. Modulation of microwave reflectometry signals at the fast wave frequency is being used to investigate fast wave propagation and damping. Additionally, rf pick-up probes on the internal boundary of the vessel provide a comparison with ray tracing codes, with dear evidence for a toroidally directed wave with antenna phasing set for current drive. There is some experimental evidence for fast wave absorption by energetic beam ions at high cyclotron harmonic resonances

Large-Scale Testing and High-Fidelity Simulation Capabilities at Sandia National Laboratories to Support Space Power and Propulsion

International Nuclear Information System (INIS)

Dobranich, Dean; Blanchat, Thomas K.

2008-01-01

Sandia National Laboratories, as a Department of Energy, National Nuclear Security Agency, has major responsibility to ensure the safety and security needs of nuclear weapons. As such, with an experienced research staff, Sandia maintains a spectrum of modeling and simulation capabilities integrated with experimental and large-scale test capabilities. This expertise and these capabilities offer considerable resources for addressing issues of interest to the space power and propulsion communities. This paper presents Sandia's capability to perform thermal qualification (analysis, test, modeling and simulation) using a representative weapon system as an example demonstrating the potential to support NASA's Lunar Reactor System

Measurement capabilities of the Bendix Metrology Organization

International Nuclear Information System (INIS)

Barnes, L.M.

1984-01-01

The purpose of this manual is to communicate the measurement and calibration capabilities of the Metrology Organization of the Bendix Kansas City Division. Included is a listing of the measurement types and ranges available, and the accuracies normally attainable under conditions at the Kansas City Division. Also described are currently used standards and measurement devices. The manual is divided into four major sections, each describing a broad general area of measurement: mechanical; environmental, gas, liquid; electrical; and optical and radiation

PROGRAMS WITH DATA MINING CAPABILITIES

Directory of Open Access Journals (Sweden)

Ciobanu Dumitru

2012-03-01

Full Text Available The fact that the Internet has become a commodity in the world has created a framework for anew economy. Traditional businesses migrate to this new environment that offers many features and options atrelatively low prices. However competitiveness is fierce and successful Internet business is tied to rigorous use of allavailable information. The information is often hidden in data and for their retrieval is necessary to use softwarecapable of applying data mining algorithms and techniques. In this paper we want to review some of the programswith data mining capabilities currently available in this area.We also propose some classifications of this softwareto assist those who wish to use such software.

Developing Alliance Capabilities

DEFF Research Database (Denmark)

Heimeriks, Koen H.; Duysters, Geert; Vanhaverbeke, Wim

This paper assesses the differential performance effects of learning mechanisms on the development of alliance capabilities. Prior research has suggested that different capability levels could be identified in which specific intra-firm learning mechanisms are used to enhance a firm's alliance...

Experimental and numerical study of influence of ferromagnetic cover on critical current of BiSCCO-2223/Ag tape superconductor

International Nuclear Information System (INIS)

Vojenciak, M; Souc, J; Goemoery, F

2009-01-01

Samples of commercially available BiSCCO-2223/Ag tape have been partially covered by the ferromagnetic material. Improvement of the self-field critical current up to 15 % has been achieved by this procedure. A critical current of such tape strongly depends on geometric and magnetic properties of both, the superconducting tape as well as the ferromagnetic cover. Numerical simulations, based on the critical state model using commercial finite element method (FEM) code, have been performed. Properties of superconductor are characterized by anisotropic dependence of the critical current density on magnetic field as well as detail geometry of filaments. The ferromagnetic material is characterized by nonlinear magnetization curve. Nonlinear dependences of the critical current on selected parameters are shown in this work. Optimization of the cover parameters using these curves has been made. Samples with various parameters have been manufactured for the confirmation of numerical simulations results. Experimental results are in good qualitative agreement with results obtained by numerical simulations.

Low Voltage Ride-Through Capability Solutions for Permanent Magnet Synchronous Wind Generators

Directory of Open Access Journals (Sweden)

Victor F. Mendes

2016-01-01

Full Text Available Due to the increasing number of wind power plants, several countries have modified their grid codes to include specific requirements for the connection of this technology to the power system. One of the requirements is the ride-through fault capability (RTFC, i.e., the system capability to sustain operation during voltage sags. In this sense, the present paper intends to investigate the behavior of a full-converter wind generator with a permanent magnet synchronous machine during symmetrical and asymmetrical voltage sags. Two solutions to improve the low voltage ride-through capability (LVRT of this technology are analyzed: discharging resistors (brake chopper and resonant controllers (RCs. The design and limitations of these solutions and the others proposed in the literature are discussed. Experimental results in a 34 kW test bench, which represents a scaled prototype of a real 2 MW wind conversion system, are presented.

Leadership capabilities of physiotherapy leaders in Ireland: Part 1 physiotherapy managers.

Science.gov (United States)

McGowan, Emer; Elliott, Naomi; Stokes, Emma

2018-05-07

Investigation of the leadership capabilities of physiotherapists is needed to allow understanding of current leadership practice and to enable appropriate training programs to be developed. To explore physiotherapy managers´ perceptions of their leadership capabilities. Semi-structured interviews were conducted with a purposive sample of 18 physiotherapy managers from a range of public services and private practices in Ireland. The interviews were analyzed using template analysis and the coding template was based on the Bolman and Deal Leadership framework which details four leadership frames: structural, human resource, political, and symbolic. The physiotherapy managers described demonstrating leadership capabilities associated with each of the four leadership frames. However, the language used by the physiotherapy managers suggested that they work predominantly through the structural and human resource frames. The employment of capabilities associated with the political frame varied between participants; some participants described working through this frame while others reported difficulties. The symbolic frame was underused; there were fewer examples given of capabilities such as communicating their vision, demonstrating passion and facilitating a positive workplace culture. Physiotherapy managers work predominantly through the structural and human resource frames. To successfully meet the leadership requirements of their roles physiotherapy managers may benefit from specific leadership development training to develop leadership capabilities in the political and symbolic frames.

Experimental high-speed network

Science.gov (United States)

McNeill, Kevin M.; Klein, William P.; Vercillo, Richard; Alsafadi, Yasser H.; Parra, Miguel V.; Dallas, William J.

1993-09-01

Many existing local area networking protocols currently applied in medical imaging were originally designed for relatively low-speed, low-volume networking. These protocols utilize small packet sizes appropriate for text based communication. Local area networks of this type typically provide raw bandwidth under 125 MHz. These older network technologies are not optimized for the low delay, high data traffic environment of a totally digital radiology department. Some current implementations use point-to-point links when greater bandwidth is required. However, the use of point-to-point communications for a total digital radiology department network presents many disadvantages. This paper describes work on an experimental multi-access local area network called XFT. The work includes the protocol specification, and the design and implementation of network interface hardware and software. The protocol specifies the Physical and Data Link layers (OSI layers 1 & 2) for a fiber-optic based token ring providing a raw bandwidth of 500 MHz. The protocol design and implementation of the XFT interface hardware includes many features to optimize image transfer and provide flexibility for additional future enhancements which include: a modular hardware design supporting easy portability to a variety of host system buses, a versatile message buffer design providing 16 MB of memory, and the capability to extend the raw bandwidth of the network to 3.0 GHz.

Radioactive waste material testing capabilities in Romania

International Nuclear Information System (INIS)

Vieru, G.

1999-01-01

Radioactive material including wastes, generated by Romanian nuclear facilities are packaged in accordance with national and IAEA's Regulation for a safe transport to the disposal center. The evaluation and certification of packages is accomplished by subjecting these packages to normal and simulated test conditions in order to prove the package to technical performances. The standards provide to package designers the possibility to use analysis, testing or a combination of these. The paper describes the experimental and simulating qualification tests for type A packages used for transport and storage of radioactive wastes (low level). Testing are used to substantiate assumptions used in analytical models and to demonstrate package structural response. There are also presented testing capabilities which are used to perform and simulate the required qualification tests. By direct comparison of analysis and experimental results, the degree of reliability of analytical methods and admissibility of assumptions taken in package designing and in demonstrating its safety under conditions of INR - Pitesti, within the contract between the INR - Pitesti and IAEA - Vienna, were determined. (author)

Development of covariance capabilities in EMPIRE code

Energy Technology Data Exchange (ETDEWEB)

Herman,M.; Pigni, M.T.; Oblozinsky, P.; Mughabghab, S.F.; Mattoon, C.M.; Capote, R.; Cho, Young-Sik; Trkov, A.

2008-06-24

The nuclear reaction code EMPIRE has been extended to provide evaluation capabilities for neutron cross section covariances in the thermal, resolved resonance, unresolved resonance and fast neutron regions. The Atlas of Neutron Resonances by Mughabghab is used as a primary source of information on uncertainties at low energies. Care is taken to ensure consistency among the resonance parameter uncertainties and those for thermal cross sections. The resulting resonance parameter covariances are formatted in the ENDF-6 File 32. In the fast neutron range our methodology is based on model calculations with the code EMPIRE combined with experimental data through several available approaches. The model-based covariances can be obtained using deterministic (Kalman) or stochastic (Monte Carlo) propagation of model parameter uncertainties. We show that these two procedures yield comparable results. The Kalman filter and/or the generalized least square fitting procedures are employed to incorporate experimental information. We compare the two approaches analyzing results for the major reaction channels on {sup 89}Y. We also discuss a long-standing issue of unreasonably low uncertainties and link it to the rigidity of the model.

Current leads for superconducting magnets

International Nuclear Information System (INIS)

Ishibashi, Kenji

1989-01-01

Current leads for superconducting magnets have been studied since 1960's. The technology of current leads may seem to have been established both in theory and experiment before the middle of 1970's. Nevertheless, a wide variety of superconducting magnets have been introduced in the last 15 years, and the demands for special current leads have increased in accordance to the variety. A steady advance has been made in the design theory and fabrication of current leads. This paper describes the recent current lead technology regarding the design theory, safety in accidents, and high current capability. (author)

Preface to special issue of selected papers from Theoretical, Experimental, and Computational Mechanics (TECM)

DEFF Research Database (Denmark)

Jabbari, Masoud; Sarlak Chivaee, Hamid; Hattel, Jesper Henri

2017-01-01

We are pleased to introduce this special issue of the Applied Mathematical Modelling journal with highlights from theTheoretical, Experimental, and Computational Mechanics Symposium (TECM-2015). This special issue consists of four rigorouslyselected papers originally presented at TECM-2015...... as a part of the 13th International Conference of Numerical Analysisand Applied Mathematics 2015 (ICNAAM 2015), which was held on 23-29 September 2015 in Rhodes, Greece.The symposium attracted a broad range of international and local leaders in theoretical, experimental, and computational mechanics across...... various fields and application. The symposium did an excellent job of outlining the current landscape of computational mechanics and its capabilities in solving complex industrial problems in the process industries, and we agree with the editor-in-chief of the journal that it is certainly worthwhile...

Experimental and numerical examination of eddy (Foucault) currents in rotating micro-coils: Generation of heat and its impact on sample temperature

Science.gov (United States)

Aguiar, Pedro M.; Jacquinot, Jacques-François; Sakellariou, Dimitris

2009-09-01

The application of nuclear magnetic resonance (NMR) to systems of limited quantity has stimulated the use of micro-coils (diameter Foucault (eddy) currents, which generate heat. We report the first data acquired with a 4 mm MACS system and spinning up to 10 kHz. The need to spin faster necessitates improved methods to control heating. We propose an approximate solution to calculate the power losses (heat) from the eddy currents for a solenoidal coil, in order to provide insight into the functional dependencies of Foucault currents. Experimental tests of the dependencies reveal conditions which result in reduced sample heating and negligible temperature distributions over the sample volume.

Experimental and numerical examination of eddy (Foucault) currents in rotating micro-coils: Generation of heat and its impact on sample temperature.

Science.gov (United States)

Aguiar, Pedro M; Jacquinot, Jacques-François; Sakellariou, Dimitris

2009-09-01

The application of nuclear magnetic resonance (NMR) to systems of limited quantity has stimulated the use of micro-coils (diameter Foucault (eddy) currents, which generate heat. We report the first data acquired with a 4mm MACS system and spinning up to 10kHz. The need to spin faster necessitates improved methods to control heating. We propose an approximate solution to calculate the power losses (heat) from the eddy currents for a solenoidal coil, in order to provide insight into the functional dependencies of Foucault currents. Experimental tests of the dependencies reveal conditions which result in reduced sample heating and negligible temperature distributions over the sample volume.

Capabilities, innovation, and overall performance in Brazilian export firms.

Directory of Open Access Journals (Sweden)

José Ednilson de Oliveira Cabral

2015-06-01

Full Text Available This article extends the current research on innovation by investigating the relationship between innovative capabilities and export firms’ overall performance. From the perspectives of the resource-based view (RBV and dynamic capability, we examine the differential and interactive effects of exploration and exploitation capabilities in product innovation for external markets and overall performance (direct and mediated by a new product. In addition, we test the moderating effect of market dynamism and the controlling effect of firm size on these relationships. Hence, the main contribution of this article is developing and empirically testing an original model, by combining these constructs that address new relationships, in an emerging country. This model was tested with data from 498 Brazilian export firms, distributed throughout all Brazilian manufacturing sectors, by firm size, and in states. The analysis was made with application of the structural equation modeling (SEM. As a result, we found support for the assumptions that exploitation capabilities influence product innovation and overall performance, whereas exploration capabilities and their interaction to exploitation capabilities influence overall performance, but not product innovation. Additionally, the relationship between exploitation capabilities and overall performance is mediated by product innovation. Unlike hypothesized, market dynamism does not moderate the relationship between product innovation and overall performance. Furthermore, firm size works as a controlling variable in the relationships analyzed. Regarding the implications for theory, this study contributes to grasp that exploitation capabilities influences a firm’s overall performance, both directly and indirectly (via product innovation, and highlights the various direct and mediatory effects of innovation on overall performance. These insights show the importance of considering the role of mediating and

Photoresist thin-film effects on alignment process capability

Science.gov (United States)

Flores, Gary E.; Flack, Warren W.

1993-08-01

Two photoresists were selected for alignment characterization based on their dissimilar coating properties and observed differences on alignment capability. The materials are Dynachem OFPR-800 and Shipley System 8. Both photoresists were examined on two challenging alignment levels in a submicron CMOS process, a nitride level and a planarized second level metal. An Ultratech Stepper model 1500 which features a darkfield alignment system with a broadband green light for alignment signal detection was used for this project. Initially, statistically designed linear screening experiments were performed to examine six process factors for each photoresist: viscosity, spin acceleration, spin speed, spin time, softbake time, and softbake temperature. Using the results derived from the screening experiments, a more thorough examination of the statistically significant process factors was performed. A full quadratic experimental design was conducted to examine viscosity, spin speed, and spin time coating properties on alignment. This included a characterization of both intra and inter wafer alignment control and alignment process capability. Insight to the different alignment behavior is analyzed in terms of photoresist material properties and the physical nature of the alignment detection system.

Critical-state model for the determination of critical currents in disk-shaped superconductors

International Nuclear Information System (INIS)

Frankel, D.J.

1979-01-01

A series of experiments has been carried out on the flux trapping and shielding capabilities of a flat strip of Nb-Ti/Cu composite material. A circular piece of material from the strip was tested in a uniform field directed perpendicularly to the surface of the sample. Profiles of the normal component of the field along the sample diameter were measured. The critical-state model was adapted for this geometry and proved capable of reproducing the measured field profiles. Model curves agreed well with experimental field profiles generated when the full sample was in the critical state, when only a portion of the sample was in the critical state, and when profiles were obtained after the direction of the rate change of the magnetic field was reversed. The adaption of the critical-state model to disk geometry provides a possible method either to derive values of the critical current from measurements of field profiles above thin flat samples, or to predict the trapping and shielding behavior of such samples if the critical current is already known. This method of determining critical currents does not require that samples be formed into narrow strips or wires, as is required for direct measurements of J/sub c/, or into tubes or cylinders, as is usually required for magnetization-type measurements. Only a relatively small approximately circular piece of material is needed. The method relies on induced currents, so there is no need to pass large currents into the sample. The field-profile measurements are easily performed with expensive Hall probes and do not require detection of the resistive transition of the superconductor

Experimental study of the positive leader velocity as a function of the current in the initial and final-jump phases of a spark discharge

International Nuclear Information System (INIS)

Andreev, A. G.; Bazelyan, E. M.; Bulatov, M. U.; Kuzhekin, I. P.; Makalsky, L. M.; Sukharevskij, D. I.; Syssoev, V. S.

2008-01-01

A positive leader in air at gap lengths of up to 8 m was studied experimentally on an open experimental stand. The voltage source was a 6-MV pulsed voltage generator or an artificial charged aerosol cloud. The dependence of the leader velocity on the current in the range 0.2-8 A was determined by simultaneously recording the optical picture and electric parameters of the discharge. Particular attention was paid to the final-jump phase of the discharge, when the gap was completely bridged by the streamer zone of the leader. It is shown that the character of the dependence of the leader velocity on the current in this phase remains unchanged; hence, the final-jump phase can be used in experiments in which the current has to be varied within a wide range. For this purpose, one can use a damping resistance, which is inefficient in the initial phase. The parameters of the power-law dependence of the leader velocity on the current at currents of a few amperes are established reliably. It is found that the power-law dependence with constant parameters is inapplicable to calculate the leader velocity at currents of about 0.1 A, which correspond to the lower limit of the leader viability.

Scientific user facilities at Oak Ridge National Laboratory: New research capabilities and opportunities

Science.gov (United States)

Roberto, James

2011-10-01

Over the past decade, Oak Ridge National Laboratory (ORNL) has transformed its research infrastructure, particularly in the areas of neutron scattering, nanoscale science and technology, and high-performance computing. New facilities, including the Spallation Neutron Source, Center for Nanophase Materials Sciences, and Leadership Computing Facility, have been constructed that provide world-leading capabilities in neutron science, condensed matter and materials physics, and computational physics. In addition, many existing physics-related facilities have been upgraded with new capabilities, including new instruments and a high- intensity cold neutron source at the High Flux Isotope Reactor. These facilities are operated for the scientific community and are available to qualified users based on competitive peer-reviewed proposals. User facilities at ORNL currently welcome more than 2,500 researchers each year, mostly from universities. These facilities, many of which are unique in the world, will be reviewed including current and planned research capabilities, availability and operational performance, access procedures, and recent research results. Particular attention will be given to new neutron scattering capabilities, nanoscale science, and petascale simulation and modeling. In addition, user facilities provide a portal into ORNL that can enhance the development of research collaborations. The spectrum of partnership opportunities with ORNL will be described including collaborations, joint faculty, and graduate research and education.

Study on model current predictive control method of PV grid- connected inverters systems with voltage sag

Science.gov (United States)

Jin, N.; Yang, F.; Shang, S. Y.; Tao, T.; Liu, J. S.

2016-08-01

According to the limitations of the LVRT technology of traditional photovoltaic inverter existed, this paper proposes a low voltage ride through (LVRT) control method based on model current predictive control (MCPC). This method can effectively improve the photovoltaic inverter output characteristics and response speed. The MCPC method of photovoltaic grid-connected inverter designed, the sum of the absolute value of the predictive current and the given current error is adopted as the cost function with the model predictive control method. According to the MCPC, the optimal space voltage vector is selected. Photovoltaic inverter has achieved automatically switches of priority active or reactive power control of two control modes according to the different operating states, which effectively improve the inverter capability of LVRT. The simulation and experimental results proves that the proposed method is correct and effective.

Experimental observations of the tearing of an electron current sheet

International Nuclear Information System (INIS)

Gekelman, W.; Pfister, H.

1988-01-01

A neutral magnetic sheet, in which the current is carried mainly by the electrons, is set up in a laboratory plasma. By forcing the current through a thin slot, the ratio of the length to height t of the sheet may be varied; the current is observed to tear when tapprox. >30. The structure of the magnetic islands and their associated currents is fully three dimensional, although a linear two-dimensional theory gives a very good estimate of the tearing mode growth time. Tearing is accompanied by the generation of significant Hall currents, and magnetic disturbances are observed to propagate at the whistler wave speed

Axial mercury segregation in direct current operated low-pressure argon-mercury gas discharges: Part I. Experimental

International Nuclear Information System (INIS)

Gielen, John W A M; Groot, Simon de; Mullen, Joost J A M van der

2004-01-01

Due to cataphoresis, axial segregation of mercury will occur when the gas discharge of a fluorescent lamp is operated by means of a direct current. A consequence of this is a non-uniform axial luminance distribution along the lamp. To determine the degree of axial mercury segregation experimentally, axial luminance distributions have been measured which are converted into axial mercury vapour pressure distributions by an appropriate calibration method. The mercury segregation has been investigated for variations in lamp tube radius (3.6-4.8 mm), argon buffer gas pressure (200-600 Pa) and lamp current (100-250 mA) at mercury vapour pressures set at the anode in the range from 0.2 to 9.0 Pa. From the experiments it has been concluded that the mercury vapour pressure gradient at any axial position for a certain lamp tube diameter, argon pressure and lamp current depends on the local mercury vapour pressure. This observation is in contrast to assumptions made in earlier modelling publications in which one mercury vapour pressure gradient is used for all axial positions. By applying a full factorial design, an empirical relation of the mercury segregation is found for any set of parameters inside the investigated parameter ranges

Development of the experimental procedure to examine the response of carbon fiber-reinforced polymer composites subjected to a high-intensity pulsed electric field and low-velocity impact.

Science.gov (United States)

Hart, Robert J; Zhupanska, Olesya I

2016-01-01

A new fully automated experimental setup has been developed to study the response of carbon fiber reinforced polymer (CFRP) composites subjected to a high-intensity pulsed electric field and low-velocity impact. The experimental setup allows for real-time measurements of the pulsed electric current, voltage, impact load, and displacements on the CFRP composite specimens. The setup includes a new custom-built current pulse generator that utilizes a bank of capacitor modules capable of producing a 20 ms current pulse with an amplitude of up to 2500 A. The setup enabled application of the pulsed current and impact load and successfully achieved coordination between the peak of the current pulse and the peak of the impact load. A series of electrical, impact, and coordinated electrical-impact characterization tests were performed on 32-ply IM7/977-3 unidirectional CFRP composites to assess their ability to withstand application of a pulsed electric current and determine the effects of the pulsed current on the impact response. Experimental results revealed that the electrical resistance of CFRP composites decreased with an increase in the electric current magnitude. It was also found that the electrified CFRP specimens withstood higher average impact loads compared to the non-electrified specimens.

Key Future Engineering Capabilities for Human Capital Retention

Science.gov (United States)

Sivich, Lorrie

Projected record retirements of Baby Boomer generation engineers have been predicted to result in significant losses of mission-critical knowledge in space, national security, and future scientific ventures vital to high-technology corporations. No comprehensive review or analysis of engineering capabilities has been performed to identify threats related to the specific loss of mission-critical knowledge posed by the increasing retirement of tenured engineers. Archival data from a single diversified Fortune 500 aerospace manufacturing engineering company's engineering career database were analyzed to ascertain whether relationships linking future engineering capabilities, engineering disciplines, and years of engineering experience could be identified to define critical knowledge transfer models. Chi square, logistic, and linear regression analyses were used to map patterns of discipline-specific, mission-critical knowledge using archival data of engineers' perceptions of engineering capabilities, key developmental experiences, and knowledge learned from their engineering careers. The results from the study were used to document key engineering future capabilities. The results were then used to develop a proposed human capital retention plan to address specific key knowledge gaps of younger engineers as veteran engineers retire. The potential for social change from this study involves informing leaders of aerospace engineering corporations on how to build better quality mentoring or succession plans to fill the void of lost knowledge from retiring engineers. This plan can secure mission-critical knowledge for younger engineers for current and future product development and increased global competitiveness in the technology market.

Current-driven turbulence in plasmas

International Nuclear Information System (INIS)

Kluiver, H. de.

1977-10-01

Research on plasma heating in linear and toroidal systems using current-driven turbulence is reviewed. The motivation for this research is presented. Relations between parameters describing the turbulent plasma state and macroscopic observables are given. Several linear and toroidal devices used in current-driven turbulence studies are described, followed by a discussion of special diagnostic methods used. Experimental results on the measurement of electron and ion heating, anomalous plasma conductivity and associated turbulent fluctuation spectra are reviewed. Theories on current-driven turbulence are discussed and compared with experiments. It is demonstrated from the experimental results that current-driven turbulence occurs not only for extreme values of the electric field but also for an experimentally much more accessible and wide range of parameters. This forms a basis for a discussion on possible future applications in fusion-oriented plasma research

Transforming organizational capabilities in strategizing

DEFF Research Database (Denmark)

Jørgensen, Claus; Friis, Ole Uhrskov; Koch, Christian

2014-01-01

Offshored and networked enterprises are becoming an important if not leading organizational form and this development seriously challenges their organizational capabilities. More specifically, over the last years, SMEs have commenced entering these kinds of arrangements. As the organizational...... capabilities of SMEs are limited at the outset, even more emphasis is needed regarding the issues of developing relevant organizational capabilities. This paper aims at investigating how capabilities evolve during an offshoring process of more than 5 years in two Danish SMEs, i.e. not only short- but long......-term evolvements within the companies. We develop our framework of understanding organizational capabilities drawing on dynamic capability, relational capability and strategy as practice concepts, appreciating the performative aspects of developing new routines. Our two cases are taken from one author’s Ph...

First Materials Science Research Facility Rack Capabilities and Design Features

Science.gov (United States)

Cobb, S.; Higgins, D.; Kitchens, L.; Curreri, Peter (Technical Monitor)

2002-01-01

The first Materials Science Research Rack (MSRR-1) is the primary facility for U.S. sponsored materials science research on the International Space Station. MSRR-1 is contained in an International Standard Payload Rack (ISPR) equipped with the Active Rack Isolation System (ARIS) for the best possible microgravity environment. MSRR-1 will accommodate dual Experiment Modules and provide simultaneous on-orbit processing operations capability. The first Experiment Module for the MSRR-1, the Materials Science Laboratory (MSL), is an international cooperative activity between NASA's Marshall Space Flight Center (MSFC) and the European Space Agency's (ESA) European Space Research and Technology Center (ESTEC). The MSL Experiment Module will accommodate several on-orbit exchangeable experiment-specific Module Inserts which provide distinct thermal processing capabilities. Module Inserts currently planned for the MSL are a Quench Module Insert, Low Gradient Furnace, and a Solidification with Quench Furnace. The second Experiment Module for the MSRR-1 configuration is a commercial device supplied by MSFC's Space Products Development (SPD) Group. Transparent furnace assemblies include capabilities for vapor transport processes and annealing of glass fiber preforms. This Experiment Module is replaceable on-orbit. This paper will describe facility capabilities, schedule to flight and research opportunities.

Experimental study of blockage of monochromatic waves by counter currents

NARCIS (Netherlands)

Suastika, I.K.

1999-01-01

Blockage of waves by a current can occur if waves are propagating on a spatially varying opposing current in which the velocity is increasing in the wave propagation direction. The ongoing waves become shorter and steeper while they are propagating against the current. Blocking occurs at the

Experimental tests of the new plastic scintillator with pulse shape discrimination capabilities EJ-299-33

Energy Technology Data Exchange (ETDEWEB)

Cester, D., E-mail: davide.cester@gmail.com [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy); Nebbia, G. [INFN Sezione di Padova, Via Marzolo 8, I-35131 Padova (Italy); Stevanato, L. [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy); Pino, F. [Laboratorio de Fisica Nuclear, Universidad Simon Bolivar, Apartado 89000, 1080 A Caracas (Venezuela, Bolivarian Republic of); Viesti, G. [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy)

2014-01-21

We have studied the prototype of a new plastic scintillator material (EJ-299-33) engineered for gamma-neutron discrimination. Energy and time resolutions as well as pulse shape discrimination capability have been compared with those of standard plastic and liquid scintillators. EJ-299-33 characteristics are somewhat poorer compared to standard scintillators. However, results obtained with the new plastic material suggest its possible use in basic research (time-of-flight measurements) as well as in Homeland Security applications (neutron/gamma monitoring device)

Short term braking capability during power interruptions for integrated matrix converter

DEFF Research Database (Denmark)

Klumpner, Christian; Blaabjerg, Frede

2004-01-01

attractive. Sinusoidal input currents and bi-directional power flow are other advantages of the matrix converter, but it is less immune to power grid disturbances compared to a standard ASD. In hoisting applications, short-term braking capability during a power outage is needed until the mechanical brake...... engages or to perform more effective a combined braking. This paper proposes a new method to provide short-term braking capability during a power outage for matrix converters. A braking chopper is needed in the clamp circuit, which allows for a drastically reduction of the capacitor size. The power flow...

Experimental coherent X-ray diffractive imaging: capabilities and limitations of the technique

International Nuclear Information System (INIS)

Schropp, Andreas

2008-08-01

The investigations pursued during this work were focused on the testing of the applicability of the coherent X-ray diffractive imaging(CXDI)-method in the hard X-ray regime and different measurements were carried out at photon energies between 7 keV and 10 keV. The samples investigated were lithographically prepared two-dimensional gold structures with a size ranging from 3 μm to 10 μm as well as a cluster of gold spheres with a lateral extension of about 3.5 μm. Continuous diffraction patterns were recorded in small angle scattering geometry. In some of the measurements a scattering signal up to the edge of the detector could be measured which corresponds to a lateral resolution of about 30 nm. For certain samples it was possible to reconstruct the object from the measured diffraction data. Since the scattered intensity of non-periodic objects is weak at large scattering angles, the available photon flux is finally the main limitation of the method with regard to the achievable resolution. The experimental data were used to get an estimate of photon flux required for sub-nanometer resolution. The ptychographic iterative phase retrieval algorithm proposed by J. M. Rodenburg et al. (2004) was implemented and tested on simulated diffraction data. Additionally, a genetic algorithm has been developed and implemented for phase retrieval. This algorithm is very different from state-of-the-art algorithms and allows to introduce further experimentally important parameters such as a certain illumination function and partial coherence of the X-ray light. (orig.)

Conceptualising energy use and energy poverty using a capabilities framework

International Nuclear Information System (INIS)

Day, Rosie; Walker, Gordon; Simcock, Neil

2016-01-01

In this article we conceptualise energy use from a capabilities perspective, informed by the work of Amartya Sen, Martha Nussbaum and others following them. Building on this, we suggest a corresponding definition of energy poverty, as understood in the capabilities space. We argue that such an understanding provides a theoretically coherent means of comprehending the relationship between energy and wellbeing, and thus conceptualising energy deprivation, that makes sense across settings including both the global North and South: a coherence which has previously been lacking. At the same time, it has the flexibility to be deployed in a way that is sensitive to local contexts. Understanding energy use in the capabilities space also provides a means for identifying multiple sites of intervention, including some areas that are currently largely overlooked. We argue that this is advantageous for attempts to address energy poverty in the context of climate change and imperatives for the containment of aggregate energy consumption. - Highlights: •We apply the capabilities approach of Amartya Sen and Martha Nussbaum to conceptualising why energy is used and needed. •We propose a definition of energy poverty based on the capabilities approach. •We argue that this understanding integrates approaches to energy poverty from global North and South contexts. •The proposed definition of energy poverty is multi-dimensional. •This understanding opens new conceptual space for interventions to alleviate energy poverty.

COMPUTER SUPPORT SYSTEMS FOR ESTIMATING CHEMICAL TOXICITY: PRESENT CAPABILITIES AND FUTURE TRENDS

Science.gov (United States)

Computer Support Systems for Estimating Chemical Toxicity: Present Capabilities and Future Trends A wide variety of computer-based artificial intelligence (AI) and decision support systems exist currently to aid in the assessment of toxicity for environmental chemicals. T...

How Stakeholder Sensing and Anticipations Shape the Firm’s Strategic Response Capability

DEFF Research Database (Denmark)

Hallin, Carina Antonia; Andersen, Torben Juul; Ooi, Can-Seng

We outline a strategic response capability framework drawing on cognitive neuroscience to explain stakeholder sensing and anticipations as essential input to environmental analysis. Stakeholders receive stimuli from ongoing interactions with the firm and thereby sense current environmental changes...

High current, 0.5-MA, fast, 100-ns, linear transformer driver experiments

Directory of Open Access Journals (Sweden)

Michael G. Mazarakis

2009-05-01

Full Text Available The linear transformer driver (LTD is a new method for constructing high current, high-voltage pulsed accelerators. The salient feature of the approach is switching and inductively adding the pulses at low voltage straight out of the capacitors through low inductance transfer and soft iron core isolation. Sandia National Laboratories are actively pursuing the development of a new class of accelerator based on the LTD technology. Presently, the high current LTD experimental research is concentrated on two aspects: first, to study the repetition rate capabilities, reliability, reproducibility of the output pulses, switch prefires, jitter, electrical power and energy efficiency, and lifetime measurements of the cavity active components; second, to study how a multicavity linear array performs in a voltage adder configuration relative to current transmission, energy and power addition, and wall plug to output pulse electrical efficiency. Here we report the repetition rate and lifetime studies performed in the Sandia High Current LTD Laboratory. We first utilized the prototype ∼0.4-MA, LTD I cavity which could be reliably operated up to ±90-kV capacitor charging. Later we obtained an improved 0.5-MA, LTD II version that can be operated at ±100  kV maximum charging voltage. The experimental results presented here were obtained with both cavities and pertain to evaluating the maximum achievable repetition rate and LTD cavity performance. The voltage adder experiments with a series of double sized cavities (1 MA, ±100  kV will be reported in future publications.

A business analytics capability framework

Directory of Open Access Journals (Sweden)

Ranko Cosic

2015-09-01

Full Text Available Business analytics (BA capabilities can potentially provide value and lead to better organisational performance. This paper develops a holistic, theoretically-grounded and practically relevant business analytics capability framework (BACF that specifies, defines and ranks the capabilities that constitute an organisational BA initiative. The BACF was developed in two phases. First, an a priori conceptual framework was developed based on the Resource-Based View theory of the firm and a thematic content analysis of the BA literature. Second, the conceptual framework was further developed and refined using a three round Delphi study involving 16 BA experts. Changes from the Delphi study resulted in a refined and confirmed framework including detailed capability definitions, together with a ranking of the capabilities based on importance. The BACF will help academic researchers and industry practitioners to better understand the capabilities that constitute an organisational BA initiative and their relative importance. In future work, the capabilities in the BACF will be operationalised to measure their as-is status, thus enabling organisations to identify key areas of strength and weakness and prioritise future capability improvement efforts.

Sensor Alerting Capability

Science.gov (United States)

Henriksson, Jakob; Bermudez, Luis; Satapathy, Goutam

2013-04-01

There is a large amount of sensor data generated today by various sensors, from in-situ buoys to mobile underwater gliders. Providing sensor data to the users through standardized services, language and data model is the promise of OGC's Sensor Web Enablement (SWE) initiative. As the amount of data grows it is becoming difficult for data providers, planners and managers to ensure reliability of data and services and to monitor critical data changes. Intelligent Automation Inc. (IAI) is developing a net-centric alerting capability to address these issues. The capability is built on Sensor Observation Services (SOSs), which is used to collect and monitor sensor data. The alerts can be configured at the service level and at the sensor data level. For example it can alert for irregular data delivery events or a geo-temporal statistic of sensor data crossing a preset threshold. The capability provides multiple delivery mechanisms and protocols, including traditional techniques such as email and RSS. With this capability decision makers can monitor their assets and data streams, correct failures or be alerted about a coming phenomena.

Current status of baryon spectroscopy

International Nuclear Information System (INIS)

Wali, K.C.

1975-01-01

The basic ideas of some of the current models and the experimental numerical comparisons are discussed briefly. Included are realistic or constituent quark models, experimental comparison, the experimental and theoretical basis for the assignments, algebraic quark models, and confinement schemes

Low Voltage Current Mode Switched-Current-Mirror Mixer

Directory of Open Access Journals (Sweden)

Chunhua Wang

2009-09-01

Full Text Available A new CMOS active mixer topology can operate at 1 V supply voltage by use of SCM (switched currentmirror. Such current-mode mixer requires less voltage headroom with good linearization. Mixing is achieved with four improved current mirrors, which are alternatively activated. For ideal switching, the operation is equivalent to a conventional active mixer. This paper analyzes the performance of the SCM mixer, in comparison with the conventional mixer, demonstrating competitive performance at a lower supply voltage. Moreover, the new mixer’s die, without any passive components, is very small, and the conversion gain is easy to adjust. An experimental prototype was designed and simulated in standard chartered 0.18μm RF CMOS Process with Spectre in Cadence Design Systems. Experimental results show satisfactory mixer performance at 2.4 GHz.

Social Capital, IT Capability, and the Success of Knowledge Management Systems

Directory of Open Access Journals (Sweden)

Irene Y.L. Chen

2009-03-01

Full Text Available Many organizations have implemented knowledge management systems to support knowledge management. However, many of such systems have failed due to the lack of relationship networks and IT capability within organizations. Motivated by such concerns, this paper examines the factors that may facilitate the success of knowledge management systems. The ten constructs derived from social capital theory, resource-based view and IS success model are integrated into the current research model. Twenty-one hypotheses derived from the research model are empirically validated using a field survey of KMS users. The results suggest that social capital and organizational IT capability are important preconditions of the success of knowledge management systems. Among the posited relationships, trust, social interaction ties, IT capability do not significantly impact service quality, system quality and IT capability, respectively. Against prior expectation, service quality and knowledge quality do not significantly influence perceived KMS benefits and user satisfaction, respectively. Discussion of the results and conclusion are provided. This study then provides insights for future research avenue.

Validation of Shielding Analysis Capability of SuperMC with SINBAD

Directory of Open Access Journals (Sweden)

Chen Chaobin

2017-01-01

Full Text Available Abstract: The shielding analysis capability of SuperMC was validated with the Shielding Integral Benchmark Archive Database (SINBAD. The SINBAD was compiled by RSICC and NEA, it includes numerous benchmark experiments performed with the D-T fusion neutron source facilities of OKTAVIAN, FNS, IPPE, etc. The results from SuperMC simulation were compared with experimental data and MCNP results. Very good agreement with deviation lower than 1% was achieved and it suggests that SuperMC is reliable in shielding calculation.

Materials Capability Review Los Alamos National Laboratory May 4-7, 2009

Energy Technology Data Exchange (ETDEWEB)

Taylor, Antoniette J [Los Alamos National Laboratory

2009-01-01

Los Alamos National Laboratory (LANL) uses external peer review to measure and continuously improve the quality of its science, technology and engineering (STE). LANL uses capability reviews to assess the STE quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. STE capabilities are define to cut across directorates providing a more holistic view of the STE quality, integration to achieve mission requirements, and mission relevance. The scope of these capabilities necessitate that there will be significant overlap in technical areas covered by capability reviews (e.g ., materials research and weapons science and engineering). In addition, LANL staff may be reviewed in different capability reviews because of their varied assignments and expertise. LANL plans to perform a complete review of the Laboratory's STE capabilities (hence staff) in a three-year cycle. The principal product of an external review is a report that includes the review committee's assessments, commendations, and recommendations for STE. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). This report will be used by Laboratory Management for STE assessment and planning. The report is also provided to the Department of Energy (DOE) as part of LANL's Annual Performance Plan and to the Los Alamos National Security (LANS) LLC's Science and Technology Committee (STC) as part of its responsibilities to the LANS Board of Governors. LANL has defined fourteen

Supply capability creation process: Key milestone criteria and activities

Energy Technology Data Exchange (ETDEWEB)

Verrollot, J.; Tolonen, A.; Harkonen, J.; Haapasalo, H.

2017-07-01

The article focuses on supply capability creation (SCC) within the new product development (NPD). The purpose is to establish an SCC process describing the main SCC activities and milestone criteria in preparing the supply process for new products Design/methodology/approach: The article analyses the earlier research, carries out current state analysis of six case companies regarding the SCC areas, and proposes a SCC process. Findings: The developed SCC process aims at preparing the operational supply capability for a developed new product based on the preferred, qualified and contracted suppliers and materials along the NPD process, and ultimately at the product ramp-up. Originality/value: This paper introduces a SCC process that has not been presented earlier in the literature, highlighting the important role of the SCC for successful product ramp-ups.

Core Capabilities and Technical Enhancement -- FY-98 Annual Report

Energy Technology Data Exchange (ETDEWEB)

Miller, David Lynn

1999-04-01

The Core Capability and Technical Enhancement (CC&TE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CC&TE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CC&TE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

Core capabilities and technical enhancement, FY-98 annual report

Energy Technology Data Exchange (ETDEWEB)

Miller, D.L.

1999-04-01

The Core Capability and Technical Enhancement (CCTE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Department of Energy's Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CCTE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CCTE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

Building EOS capability for Malaysia – the options

International Nuclear Information System (INIS)

Subari, M D; Hassan, A

2014-01-01

Earth observation satellite (EOS) is currently a major tool to monitor earth dynamics and increase human understanding of earth surface process. Since the early 80s, Malaysia has been using EOS images for various applications, such as weather forecasting, land use mapping, agriculture, environment monitoring and others. Until now, all EOS images were obtained from foreign satellite systems. Realising on the strategic need of having its own capability, Malaysia embarked into EOS development programs in the early 90s. Starting with TiungSAT-1, a micro-satellite carrying small camera, then followed by RazakSAT, a small satellite carrying 2.5 m panchromatic (PAN) medium-aperture-camera, the current satellite program development, the RazakSAT-2, designed to carry a 1.0 m high resolution PAN and 4.0m multi-spectral camera, would become a strategic initiative of the government in developing and accelerating the nation's capability in the area of satellite technology and its application. Would this effort continue until all needs of the remote sensing community being fulfilled by its own EOS? This paper will analyze the intention of the Malaysian government through its National Space Policy and other related policy documents, and proposes some policy options on this. Key factors to be considered are specific data need of the EOS community, data availability and the more subjective political motivations such as national pride

The FENIX [Fusion ENgineering International EXperimental] test facility

International Nuclear Information System (INIS)

Slack, D.S.; Patrick, R.E.; Chaplin, M.R.; Miller, J.R.; Shen, S.S.; Summers, L.T.; Kerns, J.A.

1989-01-01

The Fusion ENgineering International EXperimental Magnet Facility (FENIX), under construction at Lawrence Livermore National Laboratory (LLNL), is a significant step forward in meeting the testing requirements necessary for the development of superconductor for large-scale, superconducting magnets. A 14-T, transverse field over a test volume of 150 x 60 x 150 mm in length will be capable of testing conductors the size of the International Thermonuclear Experimental Reactor (ITER). Proposed conductors for ITER measure ∼35 mm on one side and will operate at currents of up to 40 kA at fields of ∼14 T. The testing of conductors and associated components, such as joints, will require large-bore, high-field magnet facilities. FENIX is being constructed using the existing A 2o and A 2i magnets from the idle MFTF. The east and west A 2 pairs will be mounted together to form a split-pair solenoid. The pairs of magnets will be installed in a 4.0-m cryostat vessel located in the HFTF building at LLNL. Each magnet is enclosed in its own cryostat, the existing 4.0-m vessel serving only as a vacuum chamber. 4 refs., 8 figs

Campus Capability Plan

Energy Technology Data Exchange (ETDEWEB)

Adams, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Arsenlis, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bailey, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bergman, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brase, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brenner, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Camara, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Carlton, H. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cheng, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chrzanowski, P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Colson, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); East, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Farrell, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ferranti, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gursahani, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hansen, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Helms, L. L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hernandez, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jeffries, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Larson, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lu, K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McNabb, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mercer, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Skeate, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sueksdorf, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zucca, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Le, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ancria, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Scott, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Leininger, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gagliardi, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gash, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bronson, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chung, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hobson, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Meeker, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sanchez, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zagar, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Quivey, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sommer, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Atherton, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-06-06

Lawrence Livermore National Laboratory Campus Capability Plan for 2018-2028. Lawrence Livermore National Laboratory (LLNL) is one of three national laboratories that are part of the National Nuclear Security Administration. LLNL provides critical expertise to strengthen U.S. security through development and application of world-class science and technology that: Ensures the safety, reliability, and performance of the U.S. nuclear weapons stockpile; Promotes international nuclear safety and nonproliferation; Reduces global danger from weapons of mass destruction; Supports U.S. leadership in science and technology. Essential to the execution and continued advancement of these mission areas are responsive infrastructure capabilities. This report showcases each LLNL capability area and describes the mission, science, and technology efforts enabled by LLNL infrastructure, as well as future infrastructure plans.

Experimental Investigation of Comparative Process Capabilities of Metal and Ceramic Injection Molding for Precision Applications

DEFF Research Database (Denmark)

Islam, Aminul; Giannekas, Nikolaos; Marhöfer, David Maximilian

2016-01-01

and discussion presented in the paper will be useful for thorough understanding of the MIM and CIM processes and to select the right material and process for the right application or even to combine metal and ceramic materials by molding to produce metal–ceramic hybrid components.......The purpose of this paper is to make a comparative study on the process capabilities of the two branches of the powder injection molding (PIM) process—metal injection molding (MIM) and ceramic injection molding (CIM), for high-end precision applications. The state-of-the-art literature does...

Fiber transmission and generation of ultrawideband pulses by direct current modulation of semi-conductor lasers and chirp-to-intensity conversion

DEFF Research Database (Denmark)

Company Torres, Victor; Prince, Kamau; Tafur Monroy, Idelfonso

2008-01-01

Optical pulses generated by current modulation of semiconductor lasers are strongly frequency chirped. This effect has been considered pernicious for optical communications. We take advantage of this effect for the generation of ultrawideband microwave signals by using an optical filter to achieve...... chirp-to-intensity conversion. We also experimentally achieve propagation through a 20 km nonzero dispersion shifted fiber with no degradation of the signal at the receiver. Our method constitutes a prospective low-cost solution and offers integration capabilities with fiber...

Predictive modeling capabilities from incident powder and laser to mechanical properties for laser directed energy deposition

Science.gov (United States)

Shin, Yung C.; Bailey, Neil; Katinas, Christopher; Tan, Wenda

2018-01-01

This paper presents an overview of vertically integrated comprehensive predictive modeling capabilities for directed energy deposition processes, which have been developed at Purdue University. The overall predictive models consist of vertically integrated several modules, including powder flow model, molten pool model, microstructure prediction model and residual stress model, which can be used for predicting mechanical properties of additively manufactured parts by directed energy deposition processes with blown powder as well as other additive manufacturing processes. Critical governing equations of each model and how various modules are connected are illustrated. Various illustrative results along with corresponding experimental validation results are presented to illustrate the capabilities and fidelity of the models. The good correlations with experimental results prove the integrated models can be used to design the metal additive manufacturing processes and predict the resultant microstructure and mechanical properties.

Predictive modeling capabilities from incident powder and laser to mechanical properties for laser directed energy deposition

Science.gov (United States)

Shin, Yung C.; Bailey, Neil; Katinas, Christopher; Tan, Wenda

2018-05-01

This paper presents an overview of vertically integrated comprehensive predictive modeling capabilities for directed energy deposition processes, which have been developed at Purdue University. The overall predictive models consist of vertically integrated several modules, including powder flow model, molten pool model, microstructure prediction model and residual stress model, which can be used for predicting mechanical properties of additively manufactured parts by directed energy deposition processes with blown powder as well as other additive manufacturing processes. Critical governing equations of each model and how various modules are connected are illustrated. Various illustrative results along with corresponding experimental validation results are presented to illustrate the capabilities and fidelity of the models. The good correlations with experimental results prove the integrated models can be used to design the metal additive manufacturing processes and predict the resultant microstructure and mechanical properties.

Experimental Results of a DC Bus Voltage Level Control for a Load-Controlled Marine Current Energy Converter

Directory of Open Access Journals (Sweden)

Johan Forslund

2015-05-01

Full Text Available This paper investigates three load control methods for a  marine current energy converter using a vertical axis current  turbine (VACT mounted on a permanent magnet synchronous generator  (PMSG. The three cases are; a fixed AC load, a fixed pulse width  modulated (PWM DC load and DC bus voltage control of a DC  load. Experimental results show that the DC bus voltage control  reduces the variations of rotational speed by a factor of 3.5 at the cost  of slightly increased losses in the generator and transmission lines.  For all three cases, the tip speed ratio \\(\\lambda\\ can be kept close to  the expected \\(\\lambda_{opt}\\. The power coefficient is estimated to be  0.36 at \\(\\lambda_{opt}\\; however, for all three cases, the average  extracted power was about \\(\\sim 19\\\\%. A maximum power point  tracking (MPPT system, with or without water velocity measurement,  could increase the average extracted power.

Development of students learning capabilities and professional capabilities

DEFF Research Database (Denmark)

Ringtved, Ulla Lunde; Wahl, Christian; Belle, Gianna

This paper describes the work-in-progress on a project that aims todevelop a tool that via learning analytic methods enable studentsto enhance, document and assess the development of their learningcapabilities and professional capabilities in consequence of theirself-initiated study activities...... during their bachelor educations. Thetool aims at enhancing the development of students’ capabilities toself-initiate, self-regulate and self-assess their study activities.The tool uses the concept of collective intelligence as source formotivation and inspiration in self-initiating study activities...... as wellas self-assessing them. The tool is based on a heutagogical approachto support reflection on learning potential in these activities. Thisenhances the educational use of students self-initiated learningactivities by bringing visibility and evidence to them, and therebybringing value to the assessment...

Capitalizing on capabilities.

Science.gov (United States)

Ulrich, Dave; Smallwood, Norm

2004-06-01

By making the most of organizational capabilities--employees' collective skills and fields of expertise--you can dramatically improve your company's market value. Although there is no magic list of proficiencies that every organization needs in order to succeed, the authors identify 11 intangible assets that well-managed companies tend to have: talent, speed, shared mind-set and coherent brand identity, accountability, collaboration, learning, leadership, customer connectivity, strategic unity, innovation, and efficiency. Such companies typically excel in only three of these capabilities while maintaining industry parity in the other areas. Organizations that fall below the norm in any of the 11 are likely candidates for dysfunction and competitive disadvantage. So you can determine how your company fares in these categories (or others, if the generic list doesn't suit your needs), the authors explain how to conduct a "capabilities audit," describing in particular the experiences and findings of two companies that recently performed such audits. In addition to highlighting which intangible assets are most important given the organization's history and strategy, this exercise will gauge how well your company delivers on its capabilities and will guide you in developing an action plan for improvement. A capabilities audit can work for an entire organization, a business unit, or a region--indeed, for any part of a company that has a strategy to generate financial or customer-related results. It enables executives to assess overall company strengths and weaknesses, senior leaders to define strategy, midlevel managers to execute strategy, and frontline leaders to achieve tactical results. In short, it helps turn intangible assets into concrete strengths.

Maximum field capability of energy saver superconducting magnets

International Nuclear Information System (INIS)

Turkot, F.; Cooper, W.E.; Hanft, R.; McInturff, A.

1983-01-01

At an energy of 1 TeV the superconducting cable in the Energy Saver dipole magnets will be operating at ca. 96% of its nominal short sample limit; the corresponding number in the quadrupole magnets will be 81%. All magnets for the Saver are individually tested for maximum current capability under two modes of operation; some 900 dipoles and 275 quadrupoles have now been measured. The dipole winding is composed of four individually wound coils which in general come from four different reels of cable. As part of the magnet fabrication quality control a short piece of cable from both ends of each reel has its critical current measured at 5T and 4.3K. In this paper the authors describe and present the statistical results of the maximum field tests (including quench and cycle) on Saver dipole and quadrupole magnets and explore the correlation of these tests with cable critical current

Network Communication as a Service-Oriented Capability

Energy Technology Data Exchange (ETDEWEB)

Johnston, William; Johnston, William; Metzger, Joe; Collins, Michael; Burrescia, Joseph; Dart, Eli; Gagliardi, Jim; Guok, Chin; Oberman, Kevin; O' Conner, Mike

2008-01-08

In widely distributed systems generally, and in science-oriented Grids in particular, software, CPU time, storage, etc., are treated as"services" -- they can be allocated and used with service guarantees that allows them to be integrated into systems that perform complex tasks. Network communication is currently not a service -- it is provided, in general, as a"best effort" capability with no guarantees and only statistical predictability. In order for Grids (and most types of systems with widely distributed components) to be successful in performing the sustained, complex tasks of large-scale science -- e.g., the multi-disciplinary simulation of next generation climate modeling and management and analysis of the petabytes of data that will come from the next generation of scientific instrument (which is very soon for the LHC at CERN) -- networks must provide communication capability that is service-oriented: That is it must be configurable, schedulable, predictable, and reliable. In order to accomplish this, the research and education network community is undertaking a strategy that involves changes in network architecture to support multiple classes of service; development and deployment of service-oriented communication services, and; monitoring and reporting in a form that is directly useful to the application-oriented system so that it may adapt to communications failures. In this paper we describe ESnet's approach to each of these -- an approach that is part of an international community effort to have intra-distributed system communication be based on a service-oriented capability.

A system for the study of molecular contamination. [experimental vacuum chambers

Science.gov (United States)

Dillow, C. F.; Allen, T. H.; Linford, R. M. F.; Richmond, R. G.

1975-01-01

An experimental vacuum chambers was designed and fabricated to provide a wide range of experimental capability. This work chamber assembly (WCA) was conceived to establish the proof-of-principle of various techniques for studying the kinetics of contaminants and their effects. It incorporates the capability for depositing both optical and contaminant films on temperature-controlled samples, and for in-situ measurements of the vacuum ultraviolet reflectance. Ellipsometer optics are mounted on the chamber for film thickness determinations, and other features include access ports for radiation sources and instrumentation.

Development and first experimental tests of Faraday cup array.

Science.gov (United States)

Prokůpek, J; Kaufman, J; Margarone, D; Krůs, M; Velyhan, A; Krása, J; Burris-Mog, T; Busold, S; Deppert, O; Cowan, T E; Korn, G

2014-01-01

A new type of Faraday cup, capable of detecting high energy charged particles produced in a high intensity laser-matter interaction environment, has recently been developed and demonstrated as a real-time detector based on the time-of-flight technique. An array of these Faraday cups was designed and constructed to cover different observation angles with respect to the target normal direction. Thus, it allows reconstruction of the spatial distribution of ion current density in the subcritical plasma region and the ability to visualise its time evolution through time-of-flight measurements, which cannot be achieved with standard laser optical interferometry. This is a unique method for two-dimensional visualisation of ion currents from laser-generated plasmas. A technical description of the new type of Faraday cup is introduced along with an ad hoc data analysis procedure. Experimental results obtained during campaigns at the Petawatt High-Energy Laser for Heavy Ion Experiments (GSI, Darmstadt) and at the Prague Asterix Laser System (AS CR) are presented. Advantages and limitations of the used diagnostic system are discussed.

The evolution of alliance capabilities

NARCIS (Netherlands)

Heimeriks, K.H.; Duysters, G.M.; Vanhaverbeke, W.P.M.

2004-01-01

This paper assesses the effectiveness and differential performance effects of learning mechanisms on the evolution of alliance capabilities. Relying on the concept of capability lifecycles, prior research has suggested that different capability levels could be identified in which different

REBA experimenters' manual

International Nuclear Information System (INIS)

Schuch, R.L.

1977-04-01

The REBA is a high-energy, pulsed electron beam or bremsstrahlung x-ray generator whose operational purpose is to provide an energy source of short duration for conducting experiments, primarily to determine material responses to rapid surface and in-depth deposition of energy. The purpose of this manual is to serve as a basic source of information for prospective users of REBA. Included is a brief discussion of the design and operation of the facility as well as a summary of output characteristics for electron beam modes and environmental data for x-ray operation. The manual also contains a description of the REBA experimental facilities, including geometry of the test cell, instrumentation and data collection capabilities, and services and support available to experimenters

Partnership for the Revitalization of National Wind Tunnel Force Measurement Capability

Science.gov (United States)

Rhew, Ray D.; Skelley, Marcus L.; Woike, Mark R.; Bader, Jon B.; Marshall, Timothy J.

2009-01-01

Lack of funding and lack of focus on research over the past several years, coupled with force measurement capabilities being decentralized and distributed across the National Aeronautics and Space Administration (NASA) research centers, has resulted in a significant erosion of (1) capability and infrastructure to produce and calibrate force measurement systems; (2) NASA s working knowledge of those systems; and (3) the quantity of high-quality, full-capability force measurement systems available for use in aeronautics testing. Simultaneously, and at proportional rates, the capability of industry to design, manufacture, and calibrate these test instruments has been eroding primarily because of a lack of investment by the aeronautics community. Technical expertise in this technology area is a core competency in aeronautics testing; it is highly specialized and experience-based, and it represents a niche market for only a few small precision instrument shops in the United States. With this backdrop, NASA s Aeronautics Test Program (ATP) chartered a team to examine the issues and risks associated with the problem, focusing specifically on strain- gage balances. The team partnered with the U.S. Air Force s Arnold Engineering Development Center (AEDC) to exploit their combined capabilities and take a national level government view of the problem. This paper describes the team s approach, its findings, and its recommendations, and the current status for revitalizing the government s balance capability with respect to designing, fabricating, calibrating, and using the instruments.

Optical Design Capabilities at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Lawson, J.K.

2002-01-01

Optical design capabilities continue to play the same strong role at Lawrence Livermore National Laboratory (LLNL) that they have played in the past. From defense applications to the solid-state laser programs to the Atomic Vapor Laser Isotope Separation (AVLIS), members of the optical design group played critical roles in producing effective system designs and are actively continuing this tradition. This talk will explain the role optical design plays at LLNL, outline current capabilities and summarize a few activities in which the optical design team has been recently participating. Among the many optical engineers working at LLNL, a distinct group exists which specializes in optical design issues. The optical design group collectively has a wide range of fields of expertise as well as a diversity of background histories including LLNL, university, industry and aerospace experience. This unique resource has resulted many effective and productive designs for customers at LLNL and outside the lab.

Simulation study and experimental results for detection and classification of the transient capacitor inrush current using discrete wavelet transform and artificial intelligence

Directory of Open Access Journals (Sweden)

Patcharoen Theerasak

2018-04-01

Full Text Available This paper describes the combination of discrete wavelet transforms (DWT and artificial intelligence (AI, which are efficient techniques to identify the type of inrush current, analyze the origin and possible cause on the capacitor bank switching. The experiment setup used to verify the proposed techniques can be detected and classified the transient inrush current from normal capacitor rated current. The discrete wavelet transforms are used to detect and classify the inrush current. Then, output from wavelet is acted as input of fuzzy inference system for discriminating the type of switching transient inrush current. The proposed technique shows enhanced performance with a discrimination accuracy of 90.57%. Both simulation study and experimental results are quite satisfactory with providing the high accuracy and reliability which can be developed and implemented into a numerical overcurrent (50/51 and unbalanced current (60C protection relay for an application of shunt capacitor bank protection in the future.

Simulation study and experimental results for detection and classification of the transient capacitor inrush current using discrete wavelet transform and artificial intelligence

Science.gov (United States)

Patcharoen, Theerasak; Yoomak, Suntiti; Ngaopitakkul, Atthapol; Pothisarn, Chaichan

2018-04-01

This paper describes the combination of discrete wavelet transforms (DWT) and artificial intelligence (AI), which are efficient techniques to identify the type of inrush current, analyze the origin and possible cause on the capacitor bank switching. The experiment setup used to verify the proposed techniques can be detected and classified the transient inrush current from normal capacitor rated current. The discrete wavelet transforms are used to detect and classify the inrush current. Then, output from wavelet is acted as input of fuzzy inference system for discriminating the type of switching transient inrush current. The proposed technique shows enhanced performance with a discrimination accuracy of 90.57%. Both simulation study and experimental results are quite satisfactory with providing the high accuracy and reliability which can be developed and implemented into a numerical overcurrent (50/51) and unbalanced current (60C) protection relay for an application of shunt capacitor bank protection in the future.

Capturing Firms’ Heterogeneity through Marketing and IT Capabilities in SMEs

Directory of Open Access Journals (Sweden)

María A. Ramón-Jerónimo

2017-11-01

Full Text Available To achieve sustainability, firms capable of surviving economic recessions is of key relevance; the capabilities that firms need to face dynamic environments remain an open question. In this work, a new procedure is proposed to capture firms’ heterogeneity with regard to the capabilities they possess in operating efficiently in dynamic environments. This approach enables the identification of the classes of firms that develop efficiency with a specific integration of resources. While the literature has most often measured firm capabilities using subjective measures, this study suggests the use of Data Envelopment Analysis to capture the ability to transform resources into outcomes and of Latent Class Regression to capture differences across firms that explain firms’ heterogeneity in the way they perform. By combining these two techniques, this work presents a way to identify those firms that need to invest in and develop certain capabilities. This work analyses a large dataset of manufacturing Small Medium Enterprises (SMEs extracted from the Business and Strategy survey provided by Fundación de la Sociedad Estatal de Participaciones Industriales( SEPI in Spain. The dataset used enfolds 10,960 observations from 2048 firms during the period 1994–2011. The complete dataset has been employed to calculate manufacturing firms’ efficiency. In a second step, data were cleaned to eliminate outliers, and to identify SMEs and observations with records of IT capabilities. As a result, 329 manufacturing SMEs were analysed to capture their heterogeneity. The results contribute to the current literature by explaining how manufacturing SMEs show a different need in their development of capabilities to be efficient and adapt to environmental changes. While approximately 20% of firms analysed really take advantage of recessions through their investment in R&D, the remaining 80% need to adjust their size or invest in IT capabilities to become competitive

Aquantis Ocean Current Turbine Development Project Report

Energy Technology Data Exchange (ETDEWEB)

Fleming, Alex J.

2014-08-23

The Aquantis® Current Plane (“C-Plane”) technology developed by Dehlsen Associates, LLC (DA) and Aquantis, Inc. is an ocean current turbine designed to extract kinetic energy from ocean currents. The technology is capable of achieving competitively priced base-load, continuous, and reliable power generation from a source of renewable energy not before possible in this scale or form.

Statistical methods for quality assurance basics, measurement, control, capability, and improvement

CERN Document Server

Vardeman, Stephen B

2016-01-01

This undergraduate statistical quality assurance textbook clearly shows with real projects, cases and data sets how statistical quality control tools are used in practice. Among the topics covered is a practical evaluation of measurement effectiveness for both continuous and discrete data. Gauge Reproducibility and Repeatability methodology (including confidence intervals for Repeatability, Reproducibility and the Gauge Capability Ratio) is thoroughly developed. Process capability indices and corresponding confidence intervals are also explained. In addition to process monitoring techniques, experimental design and analysis for process improvement are carefully presented. Factorial and Fractional Factorial arrangements of treatments and Response Surface methods are covered. Integrated throughout the book are rich sets of examples and problems that help readers gain a better understanding of where and how to apply statistical quality control tools. These large and realistic problem sets in combination with the...

Experimental study of falling water limitation under counter-current flow in the vertical rectangular channel

International Nuclear Information System (INIS)

Usui, Tohru; Kaminaga, Masanori; Sudo, Yukio.

1988-07-01

Quantitative understanding of critical heat flux (CHF) in the narrow vertical rectangular channel is required for the thermo-hydroulic design and the safety analysis of research reactors in which flat-plate-type fuel is adopted. Especially, critical heat flux under low downward velocity has a close relation with falling water limitation under counter-current flow. Accordingly, CCFL (Counter-current Flow Limitation) experiments were carried out for both vertical rectangular channels and vertical circular tubes varried in their size and configuration of their cross sections, to make clear CCFL characteristics in the vertical rectangular channels. In the experiments, l/de of the rectangular channel was changed from 3.5 to 180. As the results, it was clear that different equivalent hydraulic diameter de, namely width or water gap of channel, gave different CCFL characteristics of rectangular channel. But the influence of channel length l on CCFL characteristics was not observed. Besides, a dimensionless correlation to estimate a relation between upward air velocity and downward water velocity was proposed based on the present experimental results. The difference of CCFL characteristics between rectangular channels and circular tubes was also investigated. Especially for the rectangular channels, dry-patches appearing condition was made clear as a flow-map. (author)

Experiments with eddy currents: the eddy current brake

International Nuclear Information System (INIS)

Gonzalez, Manuel I

2004-01-01

A moderate-cost experimental setup is presented to help students to understand some qualitative and quantitative aspects of eddy currents. The setup operates like an eddy current brake, a device commonly used in heavy vehicles to dissipate kinetic energy by generating eddy currents. A set of simple experiments is proposed to measure eddy current losses and to relate them to various relevant parameters. Typical results for each of the experiments are presented, and comparisons with theoretical predictions are included. The experiments, which are devoted to first-year undergraduate students, deal also with other pedagogically relevant topics in electricity and magnetism, such as basic laws, electrical measurement techniques, the sources of the magnetic field and others

Brandishing Cyberattack Capabilities

Science.gov (United States)

2013-01-01

Advertising cyberwar capabilities may be helpful. It may back up a deterrence strategy. It might dissuade other states from conventional mischief or...to enable the attack.5 Many of the instruments of the attack remain with the target system, nestled in its log files, or even in the malware itself...debat- able. Even if demonstrated, what worked yesterday may not work today. But difficult does not mean impossible. Advertising cyberwar capabilities

Current status of baryon spectroscopy

International Nuclear Information System (INIS)

Wali, K.C.

1975-08-01

In this review of baryon spectroscopy, the basic ideas of some of the current models and the experimental data for their claims to success are discussed including realistic or constituent quark models, experimental comparison, the experimental and theoretical basis for the assignments, algebraic quark models, and confinement schemes

Spin currents in metallic nanostructures

Energy Technology Data Exchange (ETDEWEB)

Czeschka, Franz Dominik

2011-09-05

A pure spin current, i.e., a flow of angular momentum without accompanying net charge current, is a key ingredient in the field of spintronics. In this thesis, we experimentally investigated two different concepts for pure spin current sources suggested by theory. The first is based on a time-dependent magnetization precession which ''pumps'' a pure spin current into an adjacent non-magnetic conductor. Our experiments quantitatively corroborated important predictions expected theoretically for this approach, including the dependence of the spin current on the sample geometry and the microwave power. Even more important, we could show for the first time that the spin pumping concept is viable in a large variety of ferromagnetic materials and that it only depends on the magnetization damping. Therefore, our experiments established spin pumping as generic phenomenon and demonstrated that it is a powerful way to generate pure spin currents. The second theoretical concept is based on the conversion of charge currents into spin currents in non-magnetic nanostructures via the spin Hall effect. We experimentally investigated this approach in H-shaped, metallic nanodevices, and found that the predictions are linked to requirements not realizable with the present experimental techniques, neither in sample fabrication nor in measurement technique. Indeed, our experimental data could be consistently understood by a spin-independent transport model describing the transition from diffusive to ballistic transport. In addition, the implementation of advanced fabrication and measurement techniques allowed to discover a new non-local phenomenon, the non-local anisotropic magnetoresistance. Finally, we also studied spin-polarized supercurrents carried by spin-triplet Cooper pairs. We found that low resistance interfaces are a key requirement for further experiments in this direction. (orig.)

Supply capability creation process: Key milestone criteria and activities

Directory of Open Access Journals (Sweden)

Jordan Verrollot

2017-09-01

Full Text Available Purpose: The article focuses on supply capability creation (SCC within the new product development (NPD. The purpose is to establish an SCC process describing the main SCC activities and milestone criteria in preparing the supply process for new products Design/methodology/approach: The article analyses the earlier research, carries out current state analysis of six case companies regarding the SCC areas, and proposes a SCC process. Findings: The developed SCC process aims at preparing the operational supply capability for a developed new product based on the preferred, qualified and contracted suppliers and materials along the NPD process, and ultimately at the product ramp-up. Originality/value: This paper introduces a SCC process that has not been presented earlier in the literature, highlighting the important role of the SCC for successful product ramp-ups.

CALCULATION-EXPERIMENTAL METHOD OF RESEARCH IN A METALLIC CONDUCTOR WITH THE PULSE CURRENT OF ELECTRONIC WAVEPACKAGES AND DE BROGLIE ELECTRONIC HALF-WAVES

Directory of Open Access Journals (Sweden)

M. I. Baranov

2016-12-01

Full Text Available Purpose. Development of calculation-experimental method for a discovery and study of electronic wavepackages (EWP and of de Broglie electronic half-waves in a metallic conductor with the pulse axial-flow current of high density. Methodology. Theoretical bases of the electrical engineering, bases of quantum physics, electrophysics bases of technique of high voltage and large pulsecurrents, and also bases of technique of measuring of permanent and variable electric value. Results. On the basis of generalization of results of research of features of the longitudinal wave periodic distributing of negatively charged transmitters of electric current of conductivity in the thin round continuous zincked steel wire offered and approved in the conditions of high-voltage laboratory method for a discovery and direct determination in him of geometrical parameters of «hot» and «cold» longitudinal areas quantized periodic longitudinal EWP and accordingly the mediated determination of values of the quantized lengths formative their de Broglie electronic half-waves. It is shown that results of close quantum mechanical calculations of EWP and quantized lengths λenz/2 of longitudinal de Broglie half-waves for the probed wire long l0 well comport with the results of the executed high temperature experiments on the powerful high-voltage generator of homopolar large pulse current of millisecond duration. Originality. First calculation-experimental a way the important for the theory of electricity fact of existence is set in a round metallic explorer with the impulsive axial-flow current of the quantized coherent de Broglie electronic half-waves, amplitudes of which at the quantum number of n=1,3,9 correspond the middles of «hot» longitudinal areas of EWP. Calculation quantum mechanical correlation of type of λenz/2=l0/n got experimental confirmation, in obedience to which on length of l0 conductor the integer of quantized electronic half-waves is always laid

Substrate decoration for improvement of current-carrying capabilities of YBa2Cu3Ox thin films

International Nuclear Information System (INIS)

Khoryushin, Alexey V.; Mozhaev, Peter B.; Mozhaeva, Julia E.; Bdikin, Igor K.; Zhao, Yue; Andersen, Niels H.; Jacobsen, Claus S.; Hansen, Jørn Bindslev

2013-01-01

Highlights: ► Effects of substrate decoration on properties of YBCO thin films were studied. ► Y 2 O 3 nanoparticles, ultra-thin Y 2 O 3 and Y:ZrO 2 layers were used as decoration layer. ► Decoration improves j C (5 T and 50 K) up to 0.97 MA/cm 2 vs. 0.76 MA/cm 2 for a reference film. ► Ultra-thin layer of yttria and yttria nanoparticles have a similar effect on YBCO. ► Y 2 O 3 decoration results in power law coefficient α = 0.3 vs. α = 0.4 for a reference film. -- Abstract: The effects of substrate decoration with yttria and Y:ZrO 2 on the structural and electrical properties of the YBa 2 Cu 3 O x (YBCO) thin films are studied. The films were deposited on (LaAlO 3 ) 3 –(Sr 2 AlTaO 8 ) 7 substrates by pulsed laser deposition. Two different structures of decoration layer were applied, a template layer of nanoparticles and an uniform ultra-thin layer. Significant improvement of current-carrying capabilities was observed, especially at high external magnetic fields. Structural studies of these films reveal the presence of extended linear defects in the YBCO matrix. The formation of these structures is attributed to seeding of randomly oriented YBCO grains due to suppression of epitaxy in the very beginning of the deposition. The films of both kinds of decoration layers show nearly the same improvement of j C over the reference film at 77 and 50 K: j C (5T and 50 K) reaches 0.92 and 0.97 MA/cm 2 for uniform and template decoration layers. At 5 and 20 K the effect of template decoration layers is more beneficial: j C (5T and 20 K) values are 3.5 and 4.1 MA/cm 2 , j C (5T and 5 K) values are 6.4 and 7.9 MA/cm 2 , for uniform and template decoration layers, respectively

KSC Technical Capabilities Website

Science.gov (United States)

Nufer, Brian; Bursian, Henry; Brown, Laurette L.

2010-01-01

This document is the website pages that review the technical capabilities that the Kennedy Space Center (KSC) has for partnership opportunities. The purpose of this information is to make prospective customers aware of the capabilities and provide an opportunity to form relationships with the experts at KSC. The technical capabilities fall into these areas: (1) Ground Operations and Processing Services, (2) Design and Analysis Solutions, (3) Command and Control Systems / Services, (4) Materials and Processes, (5) Research and Technology Development and (6) Laboratories, Shops and Test Facilities.

Implementing NASA's Capability-Driven Approach: Insight into NASA's Processes for Maturing Exploration Systems

Science.gov (United States)

Williams-Byrd, Julie; Arney, Dale; Rodgers, Erica; Antol, Jeff; Simon, Matthew; Hay, Jason; Larman, Kevin

2015-01-01

NASA is engaged in transforming human spaceflight. The Agency is shifting from an exploration-based program with human activities focused on low Earth orbit (LEO) and targeted robotic missions in deep space to a more sustainable and integrated pioneering approach. Through pioneering, NASA seeks to address national goals to develop the capacity for people to work, learn, operate, live, and thrive safely beyond the Earth for extended periods of time. However, pioneering space involves more than the daunting technical challenges of transportation, maintaining health, and enabling crew productivity for long durations in remote, hostile, and alien environments. This shift also requires a change in operating processes for NASA. The Agency can no longer afford to engineer systems for specific missions and destinations and instead must focus on common capabilities that enable a range of destinations and missions. NASA has codified a capability driven approach, which provides flexible guidance for the development and maturation of common capabilities necessary for human pioneers beyond LEO. This approach has been included in NASA policy and is captured in the Agency's strategic goals. It is currently being implemented across NASA's centers and programs. Throughout 2014, NASA engaged in an Agency-wide process to define and refine exploration-related capabilities and associated gaps, focusing only on those that are critical for human exploration beyond LEO. NASA identified 12 common capabilities ranging from Environmental Control and Life Support Systems to Robotics, and established Agency-wide teams or working groups comprised of subject matter experts that are responsible for the maturation of these exploration capabilities. These teams, called the System Maturation Teams (SMTs) help formulate, guide and resolve performance gaps associated with the identified exploration capabilities. The SMTs are defining performance parameters and goals for each of the 12 capabilities

Current measurement method for characterization of fast switching power semiconductors with Silicon Steel Current Transformer

DEFF Research Database (Denmark)

Li, Helong; Beczkowski, Szymon; Munk-Nielsen, Stig

2015-01-01

This paper proposes a novel current measurement method with Silicon Steel Current Transformer (SSCT) for the characterization of fast switching power semiconductors. First, the existing current sensors for characterization of fast switching power semiconductors are experimentally evaluated...

Organizational Economics of Capability and Heterogeneity

DEFF Research Database (Denmark)

Argyres, Nicholas S.; Felin, Teppo; Foss, Nicolai Juul

2012-01-01

For decades, the literatures on firm capabilities and organizational economics have been at odds with each other, specifically relative to explaining organizational boundaries and heterogeneity. We briefly trace the history of the relationship between the capabilities literature and organizational...... economics, and we point to the dominance of a “capabilities first” logic in this relationship. We argue that capabilities considerations are inherently intertwined with questions about organizational boundaries and internal organization, and we use this point to respond to the prevalent capabilities first...... logic. We offer an integrative research agenda that focuses first on the governance of capabilities and then on the capability of governance....

A Fast Response Capability within NOAA/NOS/CO-OPS

Science.gov (United States)

2007-01-01

A Fast Response Capability within NOAA/NOS/CO-OPS P. B. Burke NOAA/National Ocean Service/CO-OPS 1305 East-West Hwy. Silver Spring, MD 20910...USA pat.burke@noaa.gov T. Graff NOAA/National Ocean Service/CO-OPS 1305 East-West Hwy. Silver Spring, MD 20910 USA tammy.graff@noaa.gov... flotation hull, an instrumentation tower mounted atop the hull and a current meter mount with a mooring attachment. The triangular tower housed two

Task-Difficulty Homeostasis in Car Following Models: Experimental Validation Using Self-Paced Visual Occlusion.

Directory of Open Access Journals (Sweden)

Jami Pekkanen

Full Text Available Car following (CF models used in traffic engineering are often criticized for not incorporating "human factors" well known to affect driving. Some recent work has addressed this by augmenting the CF models with the Task-Capability Interface (TCI model, by dynamically changing driving parameters as function of driver capability. We examined assumptions of these models experimentally using a self-paced visual occlusion paradigm in a simulated car following task. The results show strong, approximately one-to-one, correspondence between occlusion duration and increase in time headway. The correspondence was found between subjects and within subjects, on aggregate and individual sample level. The long time scale aggregate results support TCI-CF models that assume a linear increase in time headway in response to increased distraction. The short time scale individual sample level results suggest that drivers also adapt their visual sampling in response to transient changes in time headway, a mechanism which isn't incorporated in the current models.

Metrology Measurement Capabilities

Energy Technology Data Exchange (ETDEWEB)

Dr. Glen E. Gronniger

2007-10-02

This document contains descriptions of Federal Manufacturing & Technologies (FM&T) Metrology capabilities, traceability flow charts, and the measurement uncertainty of each measurement capability. Metrology provides NIST traceable precision measurements or equipment calibration for a wide variety of parameters, ranges, and state-of-the-art uncertainties. Metrology laboratories conform to the requirements of the Department of Energy Development and Production Manual Chapter 13.2, ANSI/ISO/IEC ANSI/ISO/IEC 17025:2005, and ANSI/NCSL Z540-1. FM&T Metrology laboratories are accredited by NVLAP for the parameters, ranges, and uncertainties listed in the specific scope of accreditation under NVLAP Lab code 200108-0. See the Internet at http://ts.nist.gov/Standards/scopes/2001080.pdf. These parameters are summarized. The Honeywell Federal Manufacturing & Technologies (FM&T) Metrology Department has developed measurement technology and calibration capability in four major fields of measurement: (1) Mechanical; (2) Environmental, Gas, Liquid; (3) Electrical (DC, AC, RF/Microwave); and (4) Optical and Radiation. Metrology Engineering provides the expertise to develop measurement capabilities for virtually any type of measurement in the fields listed above. A strong audit function has been developed to provide a means to evaluate the calibration programs of our suppliers and internal calibration organizations. Evaluation includes measurement audits and technical surveys.

Capable design or designing capabilities? An exploration of service design as an emerging organizational capability in Telenor – Martinkenaite

Directory of Open Access Journals (Sweden)

Ieva Martinkenaite

2017-01-01

Full Text Available This empirical paper examines a process, starting with the managerial decision to make service design an organizational capability, and follows it as it unfolds over time within one organization. Service design has become an established business practice of how firms create new products and services to promote differentiation in an increasingly uncertain business landscape. Implicit in the literature on service design are assumptions about strategic implications of adopting the prescribed innovation methods and tools. However, little is known about how service design evolves into an organizational capability enabling firms to transform their existing businesses and sustain competitiveness. Through a longitudinal, exploratory case study of service design practices in one of the world’s largest telecommunications companies, we explicate mechanisms through which service design evolves into an organizational capability by exploring the research question: what are the mechanisms through which service design develops into an organizational capability? Our study reveals the effect of an initial introduction of service design tools, identification of boundaryspanning actors and co-alignment of dedicated resources between internal functions, as well as through co-creation with customers. Over time, these activities lead to the adoption of service design practices, and subsequently these practices spark incremental learning throughout the organization, alter managerial decisions and influence multiple paths for the development of new capabilities. Reporting on this process, we are able to describe how service design practices were disseminated and institutionalized within the organization we observed. This study thus contributes by informing how service design can evolve into an organizational capability, as well as by bridging the emerging literature on service design and design thinking with established strategy theory. Further research will have to

Drift chamber electronics with multi-hit capability for time and current division measurements

Energy Technology Data Exchange (ETDEWEB)

Manarin, A; Pregernig, L; Rabany, M; Saban, R; Vismara, G

1983-11-15

Drift chambers have been installed for luminosity measurements in intersection 5 of the SPS accelerator working in panti p colliding mode. The required electronics is described. The system is able to process up to 16 hits per wire with a double pulse resolution of 40 ns; drift time and current division, with 1.25 ns and 1.6% resolution respectively, are recorded. Transconductance preamplifiers and discriminators are directly mounted on the chamber; 160 m of twisted-apir cable bring the signals to the digitizer unit. Coarse time is measured using RAM techniques, while fine time is obtained by means of a microstrip delay associated with a 100 K ECL priority encoder. Current division used a single 50 MHz Flash ADC which alows 26 dB dynamic range with 6 bit resolution. First operational results are reported.

The Capability to Hold Property

NARCIS (Netherlands)

Claassen, Rutger

2015-01-01

This paper discusses the question of whether a capability theory of justice (such as that of Martha Nussbaum) should accept a basic “capability to hold property.” Answering this question is vital for bridging the gap between abstract capability theories of justice and their institutional

IMPROVEMENTS IN THE CAPABILITY PROFILE OF 3-D PRINTING: AN UPDATE

Directory of Open Access Journals (Sweden)

Dimitrov, Dimitar Marinov

2014-08-01

Full Text Available Knowledge about the capabilities of a production system is an important issue. The three- dimensional (3-D printing (drop-on-bed process has become a well-established Additive Manufacturing (AM technology. Initially intended for use mainly as a concept modeller, its scope of application has expanded to include, among others, fit and functional models, pattern-making for casting and moulding processes, rapid tooling, and medical and architectural models. This growth in applications has stimulated a reciprocal improvement in available materials and the technological capabilities of 3-D printing, such as accuracy, strength and elongation, surface finish, build time, and cost. These factors are of significance to users who want to control their processes better and to designers who want to define their expectations and determine their requirements. Thus this paper aims to provide a technical update, highlighting the influence level of different factors on a system’s capabilities. This paper uses the example of the ZPrinter 310 system from the Z Corporation, applies appropriate statistical techniques, and takes into consideration the latest material and machine developments, in order to report on the current improvements of the capability profile of this important process.

Baseline Assessment and Prioritization Framework for IVHM Integrity Assurance Enabling Capabilities

Science.gov (United States)

Cooper, Eric G.; DiVito, Benedetto L.; Jacklin, Stephen A.; Miner, Paul S.

2009-01-01

Fundamental to vehicle health management is the deployment of systems incorporating advanced technologies for predicting and detecting anomalous conditions in highly complex and integrated environments. Integrated structural integrity health monitoring, statistical algorithms for detection, estimation, prediction, and fusion, and diagnosis supporting adaptive control are examples of advanced technologies that present considerable verification and validation challenges. These systems necessitate interactions between physical and software-based systems that are highly networked with sensing and actuation subsystems, and incorporate technologies that are, in many respects, different from those employed in civil aviation today. A formidable barrier to deploying these advanced technologies in civil aviation is the lack of enabling verification and validation tools, methods, and technologies. The development of new verification and validation capabilities will not only enable the fielding of advanced vehicle health management systems, but will also provide new assurance capabilities for verification and validation of current generation aviation software which has been implicated in anomalous in-flight behavior. This paper describes the research focused on enabling capabilities for verification and validation underway within NASA s Integrated Vehicle Health Management project, discusses the state of the art of these capabilities, and includes a framework for prioritizing activities.

Experimental program at Fermilab

International Nuclear Information System (INIS)

Jovanovic, D.

1974-01-01

The experimental program at Fermilab is briefly surveyed: accelerators and experimental areas, current experiments such as elastic scattering of π +- , K +- , p +- , on proton and deuteron total cross sections, neutrino physics, high transverse momentum [fr

A study on the prediction capability of GOTHIC and HYCA3D code for local hydrogen concentrations

International Nuclear Information System (INIS)

Choi, Y. S.; Lee, W. J.; Lee, J. J.; Park, K. C.

2002-01-01

In this study the prediction capability of GOTHIC and HYCA3D code for local hydrogen concentrations was verified with experimental results. Among the experiments, executed by SNU and other organization inside and outside of the country, the fast transient and the obstacle cases are selected. In case of large subcompartment both the code show good agreement with the experimental data. But in case of small and complex geometry or fast transient the results of GOTHIC code have the large difference from experimental ones. This represents that GOTHIC code is unsuitable for these cases. On the contrary HTCA3D code agrees well with all the experimental data

Issues in neutral currents

International Nuclear Information System (INIS)

Sehgal, L.M.

1980-01-01

The experimental results on low energy confirming the structure of the effective Lagrangian of the weak neutral current processes as predicted by the Salam-Weinberg model are reviewed. Some possible modifications of the effective Lagrangian and the feasibility of their experimental verification are also considered. (P.L.)

Developing Collaborative Product Development Capabilities

DEFF Research Database (Denmark)

Mahnke, Volker; Tran, Yen

2012-01-01

innovation strategies’. Our analyses suggest that developing such collaboration capabilities benefits from the search for complementary practices, the combination of learning styles, and the development of weak and strong ties. Results also underscore the crucial importance of co-evolution of multi......Collaborative product development capabilities support a company’s product innovation activities. In the context of the fast fashion sector, this paper examines the development of the product development capabilities (PDC) that align product development capabilities in a dual innovation context......, one, slow paced, where the firm is well established and the other, fast paced, which represents a new competitive arena in which the company competes. To understand the process associated with collaborative capability development, we studied three Scandinavian fashion companies pursuing ‘dual...

A Dangerous Idea? Freedom, Children and the Capability Approach to Education

Science.gov (United States)

Bessant, Judith

2014-01-01

This article begins by observing how education is currently appreciated primarily for its utility value, a view informed by utilitarianism and neoclassical economic theory. A critique of that framing is offered and an alternative way of valuing education informed by a Capabilities Approach is presented. In doing so, I also observe that while key…

The multipurpose thermalhydraulic test facility TOPFLOW: an overview on experimental capabilities, instrumentation and results

International Nuclear Information System (INIS)

Prasser, H.M.; Beyer, M.; Carl, H.; Manera, A.; Pietruske, H.; Schuetz, P.; Weiss, F.P.

2006-01-01

A new multipurpose thermalhydraulic test facility TOPFLOW (TwO Phase FLOW) was built and put into operation at Forschungszentrum Rossendorf in 2002 and 2003. Since then, it has been mainly used for the investigation of generic and applied steady state and transient two phase flow phenomena and the development and validation of models of computational fluid dynamic (CFD) codes in the frame of the German CFD initiative. The advantage of TOPFLOW consists in the combination of a large scale of the test channels with a wide operational range both of the flow velocities as well as of the system pressures and temperatures plus finally the availability of a special instrumentation that is capable in high spatial and temporal resolving two phase flow phenomena, for example the wire-mesh sensors. (orig.)

In-pile cladding tests at NRI Rez and PIE capabilities and experience

International Nuclear Information System (INIS)

Zmitko, M.

2002-01-01

In-pile cladding corrosion test facilities and relevant post-irradiation capabilities at NRI Rez plc are overviewed. Basic information about the research rector LVR-15 and in-pile water loops is given. An experience in the field of Zr-alloy cladding corrosion testing and investigation of cladding corrosion behaviour is demonstrated for two experimental programmes conducted at NRI Rez in the past period. The first example describes results obtained at studying of corrosion behaviour of advanced Zr-alloys under PWR conditions with a special concern to a high lithium content and subcooled surface boiling. The second example informs about completion of the experimental programme supported by the IAEA which is focused on investigation of Zircaloy-4 cladding behaviour under VVER water chemistry, thermal-hydraulic and irradiation conditions with the main to obtain experimental data for an assessment of the Zircaloy-4 cladding compatibility with VVER conditions. (author)

Implementation of the Land, Atmosphere Near Real-Time Capability for EOS (LANCE)

Science.gov (United States)

Michael, Karen; Murphy, Kevin; Lowe, Dawn; Masuoka, Edward; Vollmer, Bruce; Tilmes, Curt; Teague, Michael; Ye, Gang; Maiden, Martha; Goodman, H. Michael;

Experimental Investigation of an Automobile Air-Conditioning System using Integrated Brushless Direct Current Motor Rotary Compressor

Directory of Open Access Journals (Sweden)

Sukri M.F.

2016-01-01

Full Text Available The present study presents an experimental investigation on the effect of condenser air inlet temperature and dimensionless parameter of X on the performance of automobile air-conditioning (AAC system using integrated brushless direct current motor-rotary compressor and electronic expansion valve. The other components of AAC system are from original component of AAC system used for medium size passenger car. The experimental results showed that the increment of the condenser air inlet temperature and X caused an increase in condensing temperature, cooling capacity and compressor work, while decreasing the coefficient of performance (COP. Meanwhile, the evaporating temperature increase with the increment of condenser air inlet temperature, but decrease with decrement of X. In general, AAC system have to work at higher value of X in order to produce more cooling capacity, thereby increment in compressor work also occurs due to energy balance. However, at higher value of X, the COP of the system dropped due to dominant increase in compressor power, as opposed to a rise in cooling capacity. Due to this reason, the best operation of this compressor occurs at X = 4.96 for constant T5 (35ºC, or at T5 = 30ºC for constant X (4.96.

Rationalization and future planning for AECL's research reactor capability

International Nuclear Information System (INIS)

Slater, J.B.

1990-01-01

AECL's research reactor capability has played a crucial role in the development of Canada's nuclear program. All essential concepts for the CANDU reactors were developed and tested in the NRX and NRU reactors, and in parallel, important contributions to basic physics were made. The technical feasibility of advanced fuel cycles and of the organic-cooled option for CANDU reactors were also demonstrated in the two reactors and the WR-1 reactor. In addition, an important and growing radio-isotope production industry was established and marketed on a world-wide basis. In 1984, however, it was recognized that a review and rationalization of the research reactor capability was required. The commercial success of the CANDU reactor system had reduced the scope and size of the required development program. Limited research and development funding and competition from other research facilities and programs, required that the scope be reduced to a support basis essential to maintain strategic capability. Currently, AECL, is part-way through this rationalization program and completion should be attained during 1992/93 when the MAPLE reactor is operational and decisions on NRX decommissioning will be made. A companion paper describes some of the unique operational and maintenance problems which have resulted from this program and the solutions which have been developed. Future planning must recognize the age of the NRU reactor (currently 32 years) and the need to plan for eventual replacement. Strategy is being developed and supporting studies include a full technical assessment of the NRU reactor and the required age-related upgrading program, evaluation of the performance characteristics and costs of potential future replacement reactors, particularly the advanced MAPLE concept, and opportunities for international co-operation in developing mutually supportive research programs

Dynamic Capabilities and Performance

DEFF Research Database (Denmark)

Wilden, Ralf; Gudergan, Siegfried P.; Nielsen, Bo Bernhard

2013-01-01

are contingent on the competitive intensity faced by firms. Our findings demonstrate the performance effects of internal alignment between organizational structure and dynamic capabilities, as well as the external fit of dynamic capabilities with competitive intensity. We outline the advantages of PLS...

Experimental study of a high-current FEM with a broadband microwave system

Energy Technology Data Exchange (ETDEWEB)

Denisov, G.G.; Bratman, V.L.; Ginzburg, N.S. [Institute of Applied Physics, Nizhny Novgorod (Russian Federation)] [and others

1995-12-31

One of the main features of FELs and FEMs is the possibility of fast and wideband tuning of the resonant frequency of active media, which can be provided by changing the particle energy. For a frequency adjustable FEM-oscillator, a broadband microwave system, which is simply combined with an electron-optical FEM system and consists of an oversized waveguide and reflectors based on the microwave beams multiplication effect has been proposed and studied successfully in {open_quotes}cold{close_quotes} measurements. Here, the operating ability of a cavity, that includes some key elements of the broadband microwave system, was tested in the presence of an electron beam. To provide large particle oscillation velocities in a moderate undulator field and the presence of a guide magnetic field, the FEM operating regime of double resonance was chosen. In this regime the cyclotron as well as undulator resonance conditions were satisfied. The FEM-oscillator was investigated experimentally on a high-current accelerator {open_quotes}Sinus-6{close_quotes} that forms an electron beam with particle energy 500keV and pulse duration 25ns. The aperture with a diameter 2.5mm at the center of the anode allows to pass through only the central fraction of the electron beam with a current about 100A and a small spread of longitudinal velocities of the particles. Operating transverse velocity was pumped into the electron beam in the pulse plane undulator of a 2.4cm period. The cavity with a frequency near 45GHz consists of a square waveguide and two reflectors. The broadband up-stream reflector based on the multiplication effect had the power reflectivity coefficient more than 90% in the frequency band 10% for the H{sup 10} wave of the square waveguide with the maximum about 100% at a frequency 45GHz. The down-stream narrow-band Bragg reflector had the power reflection coefficient approximately 80% in the frequency band of 4% near 45GHz for the operating mode.

Link Between Capacity for Current Production and Syntrophic Growth in Geobacter species

Directory of Open Access Journals (Sweden)

Amelia-Elena eRotaru

2015-07-01

Full Text Available Electrodes are unnatural electron acceptors, and it is yet unknown how some Geobacter species evolved to use electrodes as terminal electron acceptors. Analysis of different Geobacter species revealed that they varied in their capacity for current production. G. metallireducens and G. hydrogenophilus generated high current densities (ca. 0.05 mA/cm2, comparable to G. sulfurreducens. G. bremensis, G. chapellei, G. humireducens, and G. uranireducens, produced much lower currents (ca. 0.05 mA/cm2 and G. bemidjiensis was previously found to not produce current. There was no correspondence between the effectiveness of current generation and Fe(III oxide reduction rates. Some high-current-density strains (G. metallireducens and G. hydrogenophilus reduced Fe(III-oxides as fast as some low-current-density strains (G. bremensis, G. humireducens, and G. uranireducens whereas other low-current-density strains (G. bemidjiensis and G. chapellei reduced Fe(III oxide as slowly as G. sulfurreducens, a high-current-density strain. However, there was a correspondence between the ability to produce higher currents and the ability to grow syntrophically. G. hydrogenophilius was found to grow in co-culture with Methanosarcina barkeri, which is capable of direct interspecies electron transfer (DIET, but not with Methanospirillium hungatei capable only of H2 or formate transfer. Conductive granular activated carbon (GAC stimulated metabolism of the G. hydrogenophilus - M. barkeri co-culture, consistent with electron exchange via DIET. These findings, coupled with the previous finding that G. metallireducens and G. sulfurreducens are also capable of DIET, suggest that evolution to optimize DIET has fortuitiously conferred the capability for high-density current production to some Geobacter species.

Author's capabilities in author indexing

International Nuclear Information System (INIS)

Ooi, Shoichi

1988-01-01

The purpose of this paper is to provide a author capability of current author indexing practices in journal literature indexing practices in 'Journal of Nuclear Science and Technology of Japan'. This Journal employed keywords freely assigned by author and not taken from INIS Thesaurus or other vocabulary list. Author examined 413 literatures, comparing keywords assigned by the literatures' authors with descriptor's (ATOMINDEX) assigned by an experienced professional indexer. The results of the comparisons showed that the average set of terms assigned by author included about 70% of all the terms assigned to the same literature by the professional indexer. Authors eventually would contribute, for the most effective point to create reference to information is at the time of its generation. Consequently, it may be possible to transfer them easily to descriptors in every secondary information system. (author)

Marketing Capability in Strategy Research

DEFF Research Database (Denmark)

Ritter, Thomas; Distel, Andreas Philipp

Following the call for a demand-side perspective of strategic management (e.g., Priem et al., 2012), a firm’s marketing capability, i.e. its ability to interact with down-stream stakeholders, becomes a pivotal element in explaining a firm’s competitiveness. While marketing capability is recognized...... in the strategic management literature as an important driver of firm performance, our review of 86 articles reveals a lack of a generally accepted definition of marketing capability, a lack of a common conceptualization as well as differences in the measurement of marketing capability. In order to build a common...... ground for advancing marketing capability research and thus supporting the demand-side perspective in strategic management, we develop an integrative framework to explain the differences and propose a research agenda for developing the field....

Strategies for developing subchannel capability in an advanced system thermalhydraulic code: a literature review

International Nuclear Information System (INIS)

Cheng, J.; Rao, Y.F.

2015-01-01

In the framework of developing next generation safety analysis tools, Canadian Nuclear Laboratories (CNL) has planned to incorporate subchannel analysis capability into its advanced system thermalhydraulic code CATHENA 4. This paper provides a literature review and an assessment of current subchannel codes. It also evaluates three code-development methods: (i) static coupling of CATHENA 4 with the subchannel code ASSERT-PV, (ii) dynamic coupling of the two codes, and (iii) fully implicit implementation for a new, standalone CATHENA 4 version with subchannel capability. Results of the review and assessment suggest that the current ASSERT-PV modules can be used as the base for the fully implicit implementation of subchannel capability in CATHENA 4, and that this option may be the most cost-effective in the long run, resulting in savings in user application and maintenance costs. In addition, improved versatility of the tool could be accomplished by the addition of new features that could be added as part of its development. The new features would improve the capabilities of the existing subchannel code in handling low, reverse, and stagnant flows often encountered in system thermalhydraulic analysis. Therefore, the method of fully implicit implementation is preliminarily recommended for further exploration. A feasibility study will be performed in an attempt to extend the present work into a preliminary development plan. (author)

Optimization of Experimental Conditions of the Pulsed Current GTAW Parameters for Mechanical Properties of SDSS UNS S32760 Welds Based on the Taguchi Design Method

Science.gov (United States)

Yousefieh, M.; Shamanian, M.; Saatchi, A.

2012-09-01

Taguchi design method with L9 orthogonal array was implemented to optimize the pulsed current gas tungsten arc welding parameters for the hardness and the toughness of super duplex stainless steel (SDSS, UNS S32760) welds. In this regard, the hardness and the toughness were considered as performance characteristics. Pulse current, background current, % on time, and pulse frequency were chosen as main parameters. Each parameter was varied at three different levels. As a result of pooled analysis of variance, the pulse current is found to be the most significant factor for both the hardness and the toughness of SDSS welds by percentage contribution of 71.81 for hardness and 78.18 for toughness. The % on time (21.99%) and the background current (17.81%) had also the next most significant effect on the hardness and the toughness, respectively. The optimum conditions within the selected parameter values for hardness were found as the first level of pulse current (100 A), third level of background current (70 A), first level of % on time (40%), and first level of pulse frequency (1 Hz), while they were found as the second level of pulse current (120 A), second level of background current (60 A), second level of % on time (60%), and third level of pulse frequency (5 Hz) for toughness. The Taguchi method was found to be a promising tool to obtain the optimum conditions for such studies. Finally, in order to verify experimental results, confirmation tests were carried out at optimum working conditions. Under these conditions, there were good agreements between the predicted and the experimental results for the both hardness and toughness.

Applicability evaluation of eddy current testing for underwater laser beam welding

International Nuclear Information System (INIS)

Kobayashi, Noriyasu; Kasuya, Takashi; Ueno, Souichi; Ochiai, Makoto; Yuguchi, Yasuhiro

2010-01-01

We clarified a defect detecting capability of eddy current testing (ECT) as a surface inspection technique for underwater laser beam welding. An underwater laser beam welding procedure includes groove caving as a preparation, laser beam welding in groove and welding surface grinding as a post treatment. Therefore groove and grinded welding surface inspections are required underwater. We curried out defect detection tests using three kinds of specimens simulated a groove, reactor vessel nozzle dissimilar metal welding materials and a laser beam welding material with a cross coil ECT probe. From experimental results, we confirmed that it is possible to detect 0.3 mm or more depth electro-discharge machining slits on machining surfaces in all specimens and an ECT has possibility as a surface inspection technique for underwater laser beam welding. (author)

Upgrade of the Gas Flow Control System of the Resistive Current Leads of the LHC Inner Triplet Magnets: Simulation and Experimental Validation

CERN Document Server

Perin, A; Casas-Cubillos, J; Pezzetti, M

2014-01-01

The 600 A and 120 A circuits of the inner triplet magnets of the Large Hadron Collider are powered by resistive gas cooled current leads. The current solution for controlling the gas flow of these leads has shown severe operability limitations. In order to allow a more precise and more reliable control of the cooling gas flow, new flowmeters will be installed during the first long shutdown of the LHC. Because of the high level of radiation in the area next to the current leads, the flowmeters will be installed in shielded areas located up to 50 m away from the current leads. The control valves being located next to the current leads, this configuration leads to long piping between the valves and the flowmeters. In order to determine its dynamic behaviour, the proposed system was simulated with a numerical model and validated with experimental measurements performed on a dedicated test bench.

Upgrade of the gas flow control system of the resistive current leads of the LHC inner triplet magnets: Simulation and experimental validation

Energy Technology Data Exchange (ETDEWEB)

Perin, A.; Casas-Cubillos, J.; Pezzetti, M. [CERN, CH-1211 Geneva 23 (Switzerland); Almeida, M. [Universidade Federal de Minas Gerais, 31270-901 Belo Horizonte (Brazil)

2014-01-29

The 600 A and 120 A circuits of the inner triplet magnets of the Large Hadron Collider are powered by resistive gas cooled current leads. The current solution for controlling the gas flow of these leads has shown severe operability limitations. In order to allow a more precise and more reliable control of the cooling gas flow, new flowmeters will be installed during the first long shutdown of the LHC. Because of the high level of radiation in the area next to the current leads, the flowmeters will be installed in shielded areas located up to 50 m away from the current leads. The control valves being located next to the current leads, this configuration leads to long piping between the valves and the flowmeters. In order to determine its dynamic behaviour, the proposed system was simulated with a numerical model and validated with experimental measurements performed on a dedicated test bench.

Current status of the scientific study of the personality disorders: an overview of epidemiological, longitudinal, experimental psychopathology, and neurobehavioral perspectives.

Science.gov (United States)

Lenzenweger, Mark F

2010-08-01

Research on the nature and development of personality disorders has grown immensely over the past thirty years. A selective summary overview is given of the current status of the scientific study of the personality disorders from several perspectives, including the epidemiological, longitudinal, experimental psychopathology, and neurobehavioral perspectives. From this research, we now know that approximately 10 percent of the general population suffer from a diagnosable personality disorder. Moreover, contrary to nearly a century of theory and clinical pedagogy, modern longitudinal studies clearly suggest that personality disorders decrease in severity over time. The mechanisms by which this change occurs are not understood at present, though it is not likely that change in underlying normal personality systems drives the change in personality disorder. The methods of the experimental psychopathology laboratory, including neuroimaging approaches, are being brought to bear on the nature of personality disorders in efforts to relate neurobiological and neurocognitive functions to personality disorder symptomatology. A model that links personality disorder feature development to underlying, interacting brain-based neurobehavioral systems is reviewed in brief. Current issues and findings illustrative of these developments are given using borderline personality disorder as an exemplar. Finally, areas of intersection between psychoanalytic treatment approaches and the growing science of personality disorder are highlighted.

Ion extraction capabilities of closely spaced grids

Science.gov (United States)

Rovang, D. C.; Wilbur, P. J.

1982-01-01

The ion extraction capabilities of accelerator systems with small screen hole diameters (less than 2.0 mm) are investigated at net-accelerating voltages of 100, 300, and 500 V. Results show that the impingement-limited perveance is not dramatically affected by reductions in screen hole diameter to 1.0 mm, but impingement-limited performance was found to be dependent on the grid separation distance, the discharge-to-total accelerating voltage ratio, and the net-to-total accelerating voltage ratio. Results obtained using small hole diameters and closely spaced grids indicate a new mode of grid operation where high current density operation can be achieved with a specified net acceleration voltage by operating the grids at a high rather than low net-to-total acceleration voltage. Beam current densities as high as 25 mA/sq cm were obtained using grids with 1.0 mm diameter holes operating at a net accelerating voltage of 500 V.

Improving Effectiveness of Capabilities in EU Conflict Prevention

DEFF Research Database (Denmark)

Rodt, Annemarie Peen

– severely challenging the Union’s current capabilities as an international security provider. The urgency of improving conflict preventive and crisis management measures is particularly pertinent in Africa, where the numbers affected by conflicts across the continent are staggering. This contribution sets...... out to answer whether – and if so how – EU responses to African conflicts have made a meaningful contribution to preventing (further) conflict. The Union’s efforts in Libya, South Sudan, Democratic Republic of Congo and Central African Republic are critically examined in a comparative case study...

The Impact of IT Capability on Employee Capability, Customer Value, Customer Satisfaction, and Business Performance

Science.gov (United States)

Chae, Ho-Chang

2009-01-01

This study empirically examines the impact of IT capability on firms' performance and evaluates whether firms' IT capabilities play a role in improving employee capability, customer value, customer satisfaction, and ultimately business performance. The results were based on comparing the business performance of the IT leader companies with that of…

Effect of Wave Accessibility on Lower Hybrid Wave Current Drive in Experimental Advanced Superconductor Tokamak with H-Mode Operation

International Nuclear Information System (INIS)

Li Xin-Xia; Xiang Nong; Gan Chun-Yun

2015-01-01

The effect of the wave accessibility condition on the lower hybrid current drive in the experimental advanced superconductor Tokamak (EAST) plasma with H-mode operation is studied. Based on a simplified model, a mode conversion layer of the lower hybrid wave between the fast wave branch and the slow wave branch is proved to exist in the plasma periphery for typical EAST H-mode parameters. Under the framework of the lower hybrid wave simulation code (LSC), the wave ray trajectory and the associated current drive are calculated numerically. The results show that the wave accessibility condition plays an important role on the lower hybrid current drive in EAST plasma. For wave rays with parallel refractive index n ‖ = 2.1 or n ‖ = 2.5 launched from the outside midplane, the wave rays may penetrate the core plasma due to the toroidal geometry effect, while numerous reflections of the wave ray trajectories in the plasma periphery occur. However, low current drive efficiency is obtained. Meanwhile, the wave accessibility condition is improved if a higher confined magnetic field is applied. The simulation results show that for plasma parameters under present EAST H-mode operation, a significant lower hybrid wave current drive could be obtained for the wave spectrum with peak value n ‖ = 2.1 if a toroidal magnetic field B T = 2.5 T is applied. (paper)

Advances in U.S. Land Imaging Capabilities

Science.gov (United States)

Stryker, T. S.

2017-12-01

Advancements in Earth observations, cloud computing, and data science are improving everyday life. Information from land-imaging satellites, such as the U.S. Landsat system, helps us to better understand the changing landscapes where we live, work, and play. This understanding builds capacity for improved decision-making about our lands, waters, and resources, driving economic growth, protecting lives and property, and safeguarding the environment. The USGS is fostering the use of land remote sensing technology to meet local, national, and global challenges. A key dimension to meeting these challenges is the full, free, and open provision of land remote sensing observations for both public and private sector applications. To achieve maximum impact, these data must also be easily discoverable, accessible, and usable. The presenter will describe the USGS Land Remote Sensing Program's current capabilities and future plans to collect and deliver land remote sensing information for societal benefit. He will discuss these capabilities in the context of national plans and policies, domestic partnerships, and international collaboration. The presenter will conclude with examples of how Landsat data is being used on a daily basis to improve lives and livelihoods.

Assessment of CFD Capability for Hypersonic Shock Wave Laminar Boundary Layer Interactions

OpenAIRE

Mehrnaz Rouhi Youssefi; Doyle Knight

2017-01-01

The goal of this study is to assess CFD capability for the prediction of shock wave laminar boundary layer interactions at hypersonic velocities. More specifically, the flow field over a double-cone configuration is simulated using both perfect gas and non-equilibrium Navier–Stokes models. Computations are compared with recent experimental data obtained from measurements conducted in the LENS XX (Large Energy National Shock Expansion Tunnel Version 2) at the Calspan University of Buffalo Rese...

Amartya Sen's Capability Approach and Education

Science.gov (United States)

Walker, Melanie

2005-01-01

The human capabilities approach developed by the economist Amartya Sen links development, quality of life and freedom. This article explores the key ideas in the capability approach of: capability, functioning, agency, human diversity and public participation in generating valued capabilities. It then considers how these ideas relate specifically…

Capability maturity models in engineering companies: case study analysis

Directory of Open Access Journals (Sweden)

Titov Sergei

2016-01-01

Full Text Available In the conditions of the current economic downturn engineering companies in Russia and worldwide are searching for new approaches and frameworks to improve their strategic position, increase the efficiency of the internal business processes and enhance the quality of the final products. Capability maturity models are well-known tools used by many foreign engineering companies to assess the productivity of the processes, to elaborate the program of business process improvement and to prioritize the efforts to optimize the whole company performance. The impact of capability maturity model implementation on cost and time are documented and analyzed in the existing research. However, the potential of maturity models as tools of quality management is less known. The article attempts to analyze the impact of CMM implementation on the quality issues. The research is based on a case study methodology and investigates the real life situation in a Russian engineering company.

The influence of reactive current on wind farm LVRT behavior

Energy Technology Data Exchange (ETDEWEB)

Li, Qing; Zhang, Mei; He, Jing; Qin, Shi-yao [China Electric Power Research Institute, Beijing (China)

2012-07-01

The Low voltage ride through (LVRT) capability of the whole wind farm is required in Chinese grid code published in 2011. In order to analyze the influence of reactive current on wind farm during grid fault, a 100 MW wind farm was simulated with the wind turbines which have been tested. Based on the validated wind turbine model, the wind farm was detailed modelled in DigSILENT/PowerFactory. The model of wind turbines, transformers, feeders, main transformers, static var compensator, and transmission lines was considered in the simulation. Under the weak and strong grid conditions, the wind farm was simulated with different wind turbine reactive current behavior during grid fault, respectively. The voltage distribution, active and reactive power transient behavior at the point of interconnection was analyzed. The results show that wind farm LVRT behavior is related to reactive current and LVRT capability of wind turbine, wind farm electrical structure and grid conditions. And it is very important for wind turbine to have a flexible dynamic reactive current control capability. (orig.)

Capabilities for innovation

DEFF Research Database (Denmark)

Nielsen, Peter; Nielsen, Rene Nesgaard; Bamberger, Simon Grandjean

2012-01-01

is a survey that collected information from 601 firms belonging to the private urban sector in Denmark. The survey was carried out in late 2010. Keywords: dynamic capabilities/innovation/globalization/employee/employer cooperation/Nordic model Acknowledgment: The GOPA study was financed by grant 20080053113......Technological developments combined with increasing levels of competition related to the ongoing globalization imply that firms find themselves in dynamic, changing environments that call for dynamic capabilities. This challenges the internal human and organizational resources of firms in general...

They see a rat, we seek a cure for diseases: the current status of animal experimentation in medical practice.

Science.gov (United States)

Kehinde, Elijah O

2013-01-01

The objective of this review article was to examine current and prospective developments in the scientific use of laboratory animals, and to find out whether or not there are still valid scientific benefits of and justification for animal experimentation. The PubMed and Web of Science databases were searched using the following key words: animal models, basic research, pharmaceutical research, toxicity testing, experimental surgery, surgical simulation, ethics, animal welfare, benign, malignant diseases. Important relevant reviews, original articles and references from 1970 to 2012 were reviewed for data on the use of experimental animals in the study of diseases. The use of laboratory animals in scientific research continues to generate intense public debate. Their use can be justified today in the following areas of research: basic scientific research, use of animals as models for human diseases, pharmaceutical research and development, toxicity testing and teaching of new surgical techniques. This is because there are inherent limitations in the use of alternatives such as in vitro studies, human clinical trials or computer simulation. However, there are problems of transferability of results obtained from animal research to humans. Efforts are on-going to find suitable alternatives to animal experimentation like cell and tissue culture and computer simulation. For the foreseeable future, it would appear that to enable scientists to have a more precise understanding of human disease, including its diagnosis, prognosis and therapeutic intervention, there will still be enough grounds to advocate animal experimentation. However, efforts must continue to minimize or eliminate the need for animal testing in scientific research as soon as possible. © 2013 S. Karger AG, Basel.

Verification of the short-circuit current making capability of high-voltage switching devices

NARCIS (Netherlands)

Smeets, R.P.P.; Linden, van der W.A.

2001-01-01

Switching-in of short-circuit current leads to pre-arcing in the switching device. Pre-arcing affects the ability of switchgear to close and latch. In three-phase systems, making is associated with transient voltage phenomena that may have a significant impact on the duration of the pre-arcing

Experimental and numerical assessment of low-frequency current distributions from UMTS and GSM mobile phones

International Nuclear Information System (INIS)

Gosselin, Marie-Christine; Kühn, Sven; Kuster, Niels

2013-01-01

The evaluation of the exposure from mobile communication devices requires consideration of electromagnetic fields (EMFs) over a broad frequency range from dc to GHz. Mobile phones in operation have prominent spectral components in the low-frequency (LF) and radio-frequency (RF) ranges. While the exposure to RF fields from mobile phones has been comprehensively assessed in the past, the LF fields have received much less attention. In this study, LF fields from mobile phones are assessed experimentally and numerically for the global system for mobile (GSM) and universal mobile telecommunications system (UMTS) communication systems and conclusions about the global (LF and RF) EMF exposure from both systems are drawn. From the measurements of the time-domain magnetic fields, it was found that the contribution from the audio signal at a normal speech level, i.e., −16 dBm0, is the same order of magnitude as the fields induced by the current bursts generated from the implementation of the GSM communication system at maximum RF output level. The B-field induced by currents in phones using the UMTS is two orders of magnitude lower than that induced by GSM. Knowing that the RF exposure from the UMTS is also two orders of magnitude lower than from GSM, it is now possible to state that there is an overall reduction of the exposure from this communication system. (paper)

Experimental and numerical assessment of low-frequency current distributions from UMTS and GSM mobile phones

Science.gov (United States)

Gosselin, Marie-Christine; Kühn, Sven; Kuster, Niels

2013-12-01

The evaluation of the exposure from mobile communication devices requires consideration of electromagnetic fields (EMFs) over a broad frequency range from dc to GHz. Mobile phones in operation have prominent spectral components in the low-frequency (LF) and radio-frequency (RF) ranges. While the exposure to RF fields from mobile phones has been comprehensively assessed in the past, the LF fields have received much less attention. In this study, LF fields from mobile phones are assessed experimentally and numerically for the global system for mobile (GSM) and universal mobile telecommunications system (UMTS) communication systems and conclusions about the global (LF and RF) EMF exposure from both systems are drawn. From the measurements of the time-domain magnetic fields, it was found that the contribution from the audio signal at a normal speech level, i.e., -16 dBm0, is the same order of magnitude as the fields induced by the current bursts generated from the implementation of the GSM communication system at maximum RF output level. The B-field induced by currents in phones using the UMTS is two orders of magnitude lower than that induced by GSM. Knowing that the RF exposure from the UMTS is also two orders of magnitude lower than from GSM, it is now possible to state that there is an overall reduction of the exposure from this communication system.

Telematics Options and Capabilities

Energy Technology Data Exchange (ETDEWEB)

Hodge, Cabell [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-05

This presentation describes the data tracking and analytical capabilities of telematics devices. Federal fleet managers can use the systems to keep their drivers safe, maintain a fuel efficient fleet, ease their reporting burden, and save money. The presentation includes an example of how much these capabilities can save fleets.

Capability Handbook- offline metrology

DEFF Research Database (Denmark)

Islam, Aminul; Marhöfer, David Maximilian; Tosello, Guido

This offline metrological capability handbook has been made in relation to HiMicro Task 3.3. The purpose of this document is to assess the metrological capability of the HiMicro partners and to gather the information of all available metrological instruments in the one single document. It provides...

A circuital model of switching behaviour of 4H-SiC p+-n-n+ diodes valid at any current and temperature

International Nuclear Information System (INIS)

Bellone, S; Benedetto, L Di; Licciardo, G D; Corte, F Della

2014-01-01

A circuital model of 4H-SiC p + -n-n + diodes is presented, which is able to describe the switching behaviour of the devices in a wide range of current, voltage and temperature, at an arbitrary instant, with comparable accuracy of numerical simulations. The model has been analytically derived under generic conditions and is capable to calculate also the dynamic spatial distribution of minority carriers in the epitaxial layer. The accuracy of the model is shown by comparison with numerical simulations and experimental measurements.

Current control of superconducting coils for fusion experimental facility

International Nuclear Information System (INIS)

Ise, T.; Etou, D.; Chikaraishi, H.; Takami, S.; Inoue, T.

2003-01-01

The LHD (Large Helical Device) has twelve superconducting coils and six dc power supplies, and following specifications are required for its control system; each coil current must be controlled independently, the steady state control error is less than 0.01% of the reference value, the current settling time for 0.1% of control error is less than 1 second, and the control system must be robust against turbulence caused by appearance and disappearance of the plasma, parameter errors and external electro-magnetic noises. In this paper, the design and test results of the coil current control system for the LHD are described. The good response and robustness are in the relation of trade off each other. H-infinity controller is one of schemes to guarantee robustness for stability. However, the independent responses of six coils were impossible by the H-infinity controller only. To resolve this problem, we applied a feed-forward control with the H-infinity control. Moreover, the advanced design method of H-infinity controller using μ-synthesis was applied to guarantee the control performance in the whole operating condition. As a result, good control results were obtained by experiments. (author)

The Capability Approach

OpenAIRE

Robeyns, Ingrid

2011-01-01

textabstract In its most general description, the capability approach is a flexible and multi-purpose normative framework, rather than a precise theory of well-being, freedom or justice. At its core are two normative claims: first, the claim that the freedom to achieve well-being is of primary moral importance, and second, that freedom to achieve well-being is to be understood in terms of people’s capabilities, that is, their real opportunities to do and be what they have reason to value. Thi...

Sandia QIS Capabilities.

Energy Technology Data Exchange (ETDEWEB)

Muller, Richard P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-07-01

Sandia National Laboratories has developed a broad set of capabilities in quantum information science (QIS), including elements of quantum computing, quantum communications, and quantum sensing. The Sandia QIS program is built atop unique DOE investments at the laboratories, including the MESA microelectronics fabrication facility, the Center for Integrated Nanotechnologies (CINT) facilities (joint with LANL), the Ion Beam Laboratory, and ASC High Performance Computing (HPC) facilities. Sandia has invested $75 M of LDRD funding over 12 years to develop unique, differentiating capabilities that leverage these DOE infrastructure investments.

State-level emergency preparedness and response capabilities.

Science.gov (United States)

Watkins, Sharon M; Perrotta, Dennis M; Stanbury, Martha; Heumann, Michael; Anderson, Henry; Simms, Erin; Huang, Monica

2011-03-01

Prior assessments of public health readiness had identified gaps in radiation preparedness. In recent years, preparedness planning has involved an "all-hazards" approach. Current assessment of the national status related to radiation public health emergency preparedness capabilities at the state and local health department levels was needed. A survey of state health departments related to radiation readiness was undertaken in 2010 by the Council of State and Territorial Epidemiologists (CSTE). States with nuclear power plants were instructed to consider their responses exclusive of capabilities and resources related to the plants given that the emergency response plans for nuclear power plants are specific and unique. Thirty-eight (76%) state health departments responded to the survey, including 26 of the 31 states with nuclear power plants. Specific strengths noted at the state level included that the majority of states had a written radiation response plan and most plans include a detailed section for communications issues during a radiation emergency. In addition, more than half of the states indicated that their relationship with federal partners is sufficient to provide resources for radiation emergencies, indicating the importance states placed on federal resources and expertise. Specific weaknesses are discussed and include that most states had completed little to no planning for public health surveillance to assess potential human health impacts of a radiation event; less than half had written plans to address exposure assessment, environmental sampling, human specimen collection and analysis, and human health assessment. Few reported having sufficient resources to do public health surveillance, radiation exposure assessment, laboratory functions and other capabilities. Levels of planning, resources and partnerships varied among states, those with nuclear power plants were better prepared. Gaps were evident in all states; however and additional training and

Current drive and sustain experiments with the bootstrap current in JT-60

International Nuclear Information System (INIS)

Kikuchi, Mitsuru; Azumi, Masafumi; Tani, Keiji; Tsuji, Shunji; Kubo, Hirotaka

1989-11-01

The current drive and sustain experiments with the neoclassical bootstrap current are performed in the JT-60 tokamak. It is shown that up to 80% of total plasma current is driven by the bootstrap current in extremely high β p regime (β p = 3.2) and the current drive product I p (bootstrap) n-bar e R p up to 4.4 x 10 19 MAm -2 has been attained with the bootstrap current. The experimental resistive loop voltages are compared with the calculations using the neoclassical resistivity with and without the bootstrap current and the Spitzer resistivity for a wide range of the plasma current (I p = 0.5 -2 MA) and the poloidal beta (β p = 0.1 - 3.2). The calculated resistive loop voltage is consistent with the neoclassical prediction including the bootstrap current. Current sustain with the bootstrap current is tested by terminating the I p feedback control during the high power neutral beam heating. An enhancement of the L/R decay time than those expected from the plasma resistivity with measured T e and Zeff has been confirmed experimentally supporting the large non-inductive current in the plasma and is consistent with the neoclassical prediction. A new technique to calculate the bootstrap current in multi-collisionality regime for finite aspect ratio tokamak has bee developed. The neoclassical bootstrap current is calculated directly through the force balance equations between viscous and friction forces according to the Hirshman-Sigmar theory. The bootstrap current driven by the fast ion component is also included. Ballooning stability of the high β p plasma are analyzed using the current profiles including the bootstrap current. The plasma pressure is close to the ballooning limit in high β p discharges. (author)

A Study on the Impact of Marketing Capability, Operations Capability, Environmental Capability and Diversification Strategy on the Performance of Hotel Industry in the UK

OpenAIRE

ZHANG, YUBO

2009-01-01

Hotel industry has been an increasingly significant service industry across the whole world. The performance measurement method is crucial for hotels’ operations. This study examines the impacts of marketing capability, operations capability, environmental capability and diversification strategy on the business performance of hotel industry in the UK. Based on the financial archival data in the database and information obtained in the firm websites from 2004 to 2007, the investigation is carr...

Overview of the ITER EC H and CD system and its capabilities

Energy Technology Data Exchange (ETDEWEB)

Omori, T., E-mail: toshimichi.omori@iter.org [ITER Organization, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Henderson, M.A. [ITER Organization, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Albajar, F. [Fusion for Energy, C/Josep Pla 2, Torres Diagonal Litoral-B3, E-08019 Barcelona (Spain); Alberti, S. [CRPP-Association EURATOM-Confederation Suisse, EPFL Ecublens, CH-1015 Lausanne (Switzerland); Baruah, U. [Institute for Plasma Research, Near Indira Bridge, Bhat, Gandhinagar 382428 (India); Bigelow, T.S. [US ITER Project Office, ORNL, 055 Commerce Park, PO Box 2008, Oak Ridge, TN 37831 (United States); Beckett, B. [ITER Organization, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Bertizzolo, R. [CRPP-Association EURATOM-Confederation Suisse, EPFL Ecublens, CH-1015 Lausanne (Switzerland); Bonicelli, T. [Fusion for Energy, C/Josep Pla 2, Torres Diagonal Litoral-B3, E-08019 Barcelona (Spain); Bruschi, A. [Istituto di Fisica del Plasma, Association EURATOM-ENEA-CNR, Milano (Italy); Caughman, J.B. [US ITER Project Office, ORNL, 055 Commerce Park, PO Box 2008, Oak Ridge, TN 37831 (United States); Chavan, R. [CRPP-Association EURATOM-Confederation Suisse, EPFL Ecublens, CH-1015 Lausanne (Switzerland); Cirant, S. [Istituto di Fisica del Plasma, Association EURATOM-ENEA-CNR, Milano (Italy); Collazos, A. [CRPP-Association EURATOM-Confederation Suisse, EPFL Ecublens, CH-1015 Lausanne (Switzerland); Cox, D.; Darbos, C. [ITER Organization, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Baar, M.R. de [Association EURATOM-FOM, 3430 BE Nieuwegein (Netherlands); Denisov, G. [Institute of Applied Physics, 46 Ulyanov Street, Nizhny Novgorod 603950 (Russian Federation); Farina, D. [Istituto di Fisica del Plasma, Association EURATOM-ENEA-CNR, Milano (Italy); Gandini, F. [ITER Organization, CS 90 046, 13067 St Paul Lez Durance Cedex (France)

2011-10-15

The Electron Cyclotron (EC) system for the ITER tokamak is designed to inject {>=}20 MW RF power into the plasma for Heating and Current Drive (H and CD) applications. The EC system consists of up to 26 gyrotrons (between 1 and 2 MW each), the associated power supplies, 24 transmission lines and 5 launchers. The EC system has a diverse range of applications including central heating and current drive, current profile tailoring and control of plasma magneto-hydrodynamic (MHD) instabilities such as the sawtooth and neoclassical tearing modes (NTMs). This diverse range of applications requires the launchers to be capable of depositing the EC power across nearly the entire plasma cross section. This is achieved by two types of antennas: an equatorial port launcher (capable of injecting up to 20 MW from the plasma axis to mid-radius) and four upper port launchers providing access from inside of mid radius to near the plasma edge. The equatorial launcher design is optimized for central heating, current drive and profile tailoring, while the upper launcher should provide a very focused and peaked current density profile to control the plasma instabilities. The overall EC system has been modified during the past 3 years taking into account the issues identified in the ITER design review from 2007 and 2008 as well as integrating new technologies. This paper will review the principal objectives of the EC system, modifications made during the past 2 years and how the design is compliant with the principal objectives.

Overview of the ITER EC H and CD system and its capabilities

International Nuclear Information System (INIS)

Omori, T.; Henderson, M.A.; Albajar, F.; Alberti, S.; Baruah, U.; Bigelow, T.S.; Beckett, B.; Bertizzolo, R.; Bonicelli, T.; Bruschi, A.; Caughman, J.B.; Chavan, R.; Cirant, S.; Collazos, A.; Cox, D.; Darbos, C.; Baar, M.R. de; Denisov, G.; Farina, D.; Gandini, F.

2011-01-01

The Electron Cyclotron (EC) system for the ITER tokamak is designed to inject ≥20 MW RF power into the plasma for Heating and Current Drive (H and CD) applications. The EC system consists of up to 26 gyrotrons (between 1 and 2 MW each), the associated power supplies, 24 transmission lines and 5 launchers. The EC system has a diverse range of applications including central heating and current drive, current profile tailoring and control of plasma magneto-hydrodynamic (MHD) instabilities such as the sawtooth and neoclassical tearing modes (NTMs). This diverse range of applications requires the launchers to be capable of depositing the EC power across nearly the entire plasma cross section. This is achieved by two types of antennas: an equatorial port launcher (capable of injecting up to 20 MW from the plasma axis to mid-radius) and four upper port launchers providing access from inside of mid radius to near the plasma edge. The equatorial launcher design is optimized for central heating, current drive and profile tailoring, while the upper launcher should provide a very focused and peaked current density profile to control the plasma instabilities. The overall EC system has been modified during the past 3 years taking into account the issues identified in the ITER design review from 2007 and 2008 as well as integrating new technologies. This paper will review the principal objectives of the EC system, modifications made during the past 2 years and how the design is compliant with the principal objectives.

UK resource base assessment of organisations and capabilities in the biomass sector

International Nuclear Information System (INIS)

1996-01-01

British Biogen is the trade association for the UK's emerging biomass industry. It has been recognised that the biomass industry has considerable export potential due to its immense scale potential overseas, and there is an accompanying need for an export development strategy for the industry. The report contains a detailed analysis of a selection of UK companies and organisations, with regard to their export capabilities, thus providing an essential pre-requisite to developing the export strategy. The fundamental aim of the study is to assess the nature, scale and current capabilities of the UK biomass industry resource base and, in turn, to determine its potential to service export markets. (author)

How does procurement capability maturity affect e-Procurement adoption and leverage purchasing in supply chain

Directory of Open Access Journals (Sweden)

Pongpanga Pongsuwan

2016-11-01

Full Text Available This study refers to the research model of Batenburg (2008 which defined procurement functions to six maturity dimensions; strategy, processes, control, organization, information, e-Technology as the starting point and indicates twenty two items to support capability maturity measurement which is called “Procurement Competitive Capability Maturity”(PCCM. This model is used for a company to assess current practices of procurement function and perceives the level of its capabilities. The data collection is from a survey of fifty-two selected procurement organizations in Southeast Asia (SEA countries; from Thailand, Vietnam, Philippines, Indonesia, Malaysia and Singapore. The objective of this study is to demonstrate the significant value of industry type, size of spending and centralized/decentralized procurement that affect procurement capability maturity. The results show that the industry has no relation to the capability maturity; the size of procurement spend has a positive relation to the capability maturity; and the centralized procurement has higher capability maturity than the decentralized. Moreover, this study extends the knowledge of e-Procurement and digital context to leverage procurement processes and visible procurement integration in an organization and across the supply chain.

Analysis and experimental verification of a control scheme for unified power quality conditioner

Energy Technology Data Exchange (ETDEWEB)

Peng Cheng Zhu; Xun Li; Yong Kang; Jian Chen [Huazhong Univ. of Science and Techmnology, Wuhan (China). Dept. of Electrical Engineering

2005-07-01

Improving power quality for sensitive load by a Unified Power Quality Conditioner (UPQC) in a distributed generation system is presented in this paper. The power balance of a UPQC, consisting of back-to-back connected series and shunt Active Filters (AF), is analysed. Based on the analysis a novel control scheme is established in a 2-phase Synchronous Rotating d-q Frame (SRF). In this control scheme, the series AF is controlled as a current source and makes the input current sinusoidal, while the shunt AF is controlled as a voltage source and keeps the load voltage in the normal value. With the proposed control strategy, the UPQC is capable of compensating not only harmonic and reactive currents of the load but also grid voltage distortion. There is no harmonic interference between harmonic-producing loads and harmonic-sensitive loads, which are connected on the common bus. The performance of a UPQC with the proposed control scheme under nonlinear load and grid voltage distortion is investigated with simulation as well as experimental works. (Author)

The capability concept – On how to define and describe capability in relation to risk, vulnerability and resilience

International Nuclear Information System (INIS)

Lindbom, Hanna; Tehler, Henrik; Eriksson, Kerstin; Aven, Terje

2015-01-01

Capabilities-based planning and capability assessment are high on the agendas of several countries and organisations as part of their risk management and emergency preparedness. Despite this, few definitions of capability exist, and they are not easily related to concepts such as risk, vulnerability and resilience. The aim of the present study was thus to broaden the scientific basis of the risk field to also include the concept of capability. The proposed definition is based on a recently developed risk framework, and we define capability as the uncertainty about and the severity of the consequences of an activity given the occurrence of the initiating event and the performed task. We provide examples of how the response capability for a fictive scenario can be described using this definition, and illustrate how our definition can be used to analyse capability assessments prepared according to the Swedish crisis management system. We have analysed the content of 25 capability assessments produced in 2011 by stakeholders on local, regional and national level. It was concluded that none addressed uncertainty to any appreciable extent, and only a third described capability in terms of consequences and task, making it difficult to relate these capability assessments to risk assessments. - Highlights: • Few definitions of capability relate to definitions of risk, vulnerability and resilience. • We relate capability to risk, vulnerability and resilience. • We define capability using the components uncertainty, consequences, event and task

Experimental results of current distribution in Rutherford-type LHC cables

CERN Document Server

Verweij, A P

2000-01-01

Current distribution among the wires of multi-strand superconducting cables is an important item for accelerator magnets. A non-uniform distribution could cause additional field distortions in the magnet bore and can as well be one of the reasons of premature quenching. Since two years electrical measurements on superconducting Rutherford-type cables are performed at CERN as part of the reception tests for the Large Hadron Collider (LHC). Cable samples of 2.4 m length are tested at currents up to 32 kA, temperatures around 1.9 and 4.3 K, and fields up to 10 T, applied perpendicularly as well as parallel to the broad face of the cable. Last year, an array of 24 Hall probes was installed in the test set-up in order to measure the self-field of the cable samples along one cable pitch. Each of the probes measures the local field generated by the current in the strands close by, and the results of the all probes reflect therefore the distribution of the strand currents. Experiments are done varying the applied fie...

Optical see-through head-mounted display with occlusion capability

Science.gov (United States)

Gao, Chunyu; Lin, Yuxiang; Hua, Hong

2013-05-01

Lack of mutual occlusion capability between computer-rendered and real objects is one of fundamental problems for most existing optical see-through head-mounted displays (OST-HMD). Without the proper occlusion management, the virtual view through an OST-HMD appears "ghost-like", floating in the real world. To address this challenge, we have developed an innovative optical scheme that uniquely combines the eyepiece and see-through relay optics to achieve an occlusion-capable OST-HMD system with a very compelling form factor and high optical performances. The proposed display system was based on emerging freeform optical design technologies and was designed for highly efficient liquid crystal on silicon (LCoS) type spatial light modulator (SLM) and bright Organic LED (OLED) microdisplay. The proposed display technology was capable of working in both indoor and outdoor environments. Our current design offered a 1280x1024 color resolution based on 0.8" microdisplay and SLM. The MTF values for the majority of the fields at the cutoff frequency of 40lps/mm, which is determined by the pixel size of the microdisplay, are better than 15%. The design achieved a diagonal FOV of 40 degrees, 31.7 degrees horizontally and 25.6 degrees vertically, an exit pupil diameter of 8mm (non-vignetted), and an eye clearance of 18mm. The optics weights about 20 grams per eye. Our proposed occlusion capable OST-HMD system can easily find myriads of applications in various military and commercial sectors such as military training, gaming and entertainment.

Synthesizing large-scale pyroclastic flows: Experimental design, scaling, and first results from PELE

Science.gov (United States)

Lube, G.; Breard, E. C. P.; Cronin, S. J.; Jones, J.

2015-03-01

Pyroclastic flow eruption large-scale experiment (PELE) is a large-scale facility for experimental studies of pyroclastic density currents (PDCs). It is used to generate high-energy currents involving 500-6500 m3 natural volcanic material and air that achieve velocities of 7-30 m s-1, flow thicknesses of 2-4.5 m, and runouts of >35 m. The experimental PDCs are synthesized by a controlled "eruption column collapse" of ash-lapilli suspensions onto an instrumented channel. The first set of experiments are documented here and used to elucidate the main flow regimes that influence PDC dynamic structure. Four phases are identified: (1) mixture acceleration during eruption column collapse, (2) column-slope impact, (3) PDC generation, and (4) ash cloud diffusion. The currents produced are fully turbulent flows and scale well to natural PDCs including small to large scales of turbulent transport. PELE is capable of generating short, pulsed, and sustained currents over periods of several tens of seconds, and dilute surge-like PDCs through to highly concentrated pyroclastic flow-like currents. The surge-like variants develop a basal <0.05 m thick regime of saltating/rolling particles and shifting sand waves, capped by a 2.5-4.5 m thick, turbulent suspension that grades upward to lower particle concentrations. Resulting deposits include stratified dunes, wavy and planar laminated beds, and thin ash cloud fall layers. Concentrated currents segregate into a dense basal underflow of <0.6 m thickness that remains aerated. This is capped by an upper ash cloud surge (1.5-3 m thick) with 100 to 10-4 vol % particles. Their deposits include stratified, massive, normally and reversely graded beds, lobate fronts, and laterally extensive veneer facies beyond channel margins.

Design and prototype of an augmented reality display with per-pixel mutual occlusion capability.

Science.gov (United States)

Wilson, Austin; Hua, Hong

2017-11-27

State-of-the-art optical see-through head-mounted displays for augmented reality (AR) applications lack mutual occlusion capability, which refers to the ability to render correct light blocking relationship when merging digital and physical objects, such that the virtual views appear to be ghost-like and lack realistic appearance. In this paper, using off-the-shelf optical components, we present the design and prototype of an AR display which is capable of rendering per-pixel mutual occlusion. Our prototype utilizes a miniature organic light emitting display coupled with a liquid crystal on silicon type spatial light modulator to achieve an occlusion capable AR display offering a 30° diagonal field of view and an angular resolution of 1.24 arcminutes, with an optical performance of > 0.4 contrast over the full field at the Nquist frequency of 24.2 cycles/degree. We experimentally demonstrate a monocular prototype achieving >100:1 dynamic range in well-lighted environments.

IEDA [Intelligent Eddy Current Data Analysis] helps make sense of eddy current data [steam generators

International Nuclear Information System (INIS)

Clark, R.

1989-01-01

The increasing sophistication of eddy current signal interpretation in steam generator tubing has improved capabilities, but has also made the process of analysis more complex and time consuming. Westinghouse has developed an intelligent computerised tool - the IEDA (Intelligent Eddy Current Data Analysis) system, to lighten the load on analysts. Since 1985, 44 plants have been inspected with IEDA, representing over 400,000 tubes. The system has provided a repeatability and a consistency not achieved by human operators. (U.K.)

Human push capability.