WorldWideScience

Sample records for current densities higher

  1. Expanding the reduced-current approach for thermoelectric generators to achieve higher volumetric power density

    DEFF Research Database (Denmark)

    Wijesooriyage, Waruna Dissanayaka; Rosendahl, Lasse

    2015-01-01

    Thermoelectrics are candidate niche electrical generator devices for energy management. At present, scientists are more focused on thermoelectric (TE) material development, but the TE module design procedure is still in a relatively virgin state. One of the most well-known methods is the reduced...... current approach (RCA) for TE module design, where the same current is induced through the p and n legs of the thermoelectric generator (TEG). The current density of each element is manipulated by changing the area of both legs. This technique leads to a TE module architecture based on the most efficient...... configuration of both p and n legs. In the current paper, we apply an extended version of this technique, to show how a TE module with a higher volumetric power density can be designed, compared to the original RCA. Our studies indicate that for some combinations of p and n material properties, optima yielding...

  2. Higher critical current density achieved in Bi-2223 High-Tc superconductors

    Directory of Open Access Journals (Sweden)

    M.S. Shalaby

    2016-07-01

    Full Text Available Bi2Sr2Ca2Cu3Ox (Bi-2223 were prepared using a solid state reaction method at different sintering times and temperatures. Structural phase identifications have been done using X-Ray analysis and refinement by Reitveld method which proves the coexistence of Bi-2223 and Bi-2212 phases. The critical transition temperature Tc and critical current density Jc values were measured using superconducting quantum interference device magnetometer (SQUID and by the magneto-optics technique. A remarkable rapid decrease to the diamagnetic signal in the magnetization versus temperature M(T at 110 K and Jc around 1.2 × 107 A/m2 at 5 K are confirmed for the Bi-2223 compound.

  3. Minimax Current Density Coil Design

    CERN Document Server

    Poole, Michael; Lopez, Hector Sanchez; Ng, Michael; Crozier, Stuart; 10.1088/0022-3727/43/9/095001

    2010-01-01

    'Coil design' is an inverse problem in which arrangements of wire are designed to generate a prescribed magnetic field when energized with electric current. The design of gradient and shim coils for magnetic resonance imaging (MRI) are important examples of coil design. The magnetic fields that these coils generate are usually required to be both strong and accurate. Other electromagnetic properties of the coils, such as inductance, may be considered in the design process, which becomes an optimization problem. The maximum current density is additionally optimized in this work and the resultant coils are investigated for performance and practicality. Coils with minimax current density were found to exhibit maximally spread wires and may help disperse localized regions of Joule heating. They also produce the highest possible magnetic field strength per unit current for any given surface and wire size. Three different flavours of boundary element method that employ different basis functions (triangular elements...

  4. Kernel current source density method.

    Science.gov (United States)

    Potworowski, Jan; Jakuczun, Wit; Lȩski, Szymon; Wójcik, Daniel

    2012-02-01

    Local field potentials (LFP), the low-frequency part of extracellular electrical recordings, are a measure of the neural activity reflecting dendritic processing of synaptic inputs to neuronal populations. To localize synaptic dynamics, it is convenient, whenever possible, to estimate the density of transmembrane current sources (CSD) generating the LFP. In this work, we propose a new framework, the kernel current source density method (kCSD), for nonparametric estimation of CSD from LFP recorded from arbitrarily distributed electrodes using kernel methods. We test specific implementations of this framework on model data measured with one-, two-, and three-dimensional multielectrode setups. We compare these methods with the traditional approach through numerical approximation of the Laplacian and with the recently developed inverse current source density methods (iCSD). We show that iCSD is a special case of kCSD. The proposed method opens up new experimental possibilities for CSD analysis from existing or new recordings on arbitrarily distributed electrodes (not necessarily on a grid), which can be obtained in extracellular recordings of single unit activity with multiple electrodes.

  5. 1D Current Source Density (CSD) Estimation in Inverse Theory: A Unified Framework for Higher-Order Spectral Regularization of Quadrature and Expansion-Type CSD Methods.

    Science.gov (United States)

    Kropf, Pascal; Shmuel, Amir

    2016-07-01

    Estimation of current source density (CSD) from the low-frequency part of extracellular electric potential recordings is an unstable linear inverse problem. To make the estimation possible in an experimental setting where recordings are contaminated with noise, it is necessary to stabilize the inversion. Here we present a unified framework for zero- and higher-order singular-value-decomposition (SVD)-based spectral regularization of 1D (linear) CSD estimation from local field potentials. The framework is based on two general approaches commonly employed for solving inverse problems: quadrature and basis function expansion. We first show that both inverse CSD (iCSD) and kernel CSD (kCSD) fall into the category of basis function expansion methods. We then use these general categories to introduce two new estimation methods, quadrature CSD (qCSD), based on discretizing the CSD integral equation with a chosen quadrature rule, and representer CSD (rCSD), an even-determined basis function expansion method that uses the problem's data kernels (representers) as basis functions. To determine the best candidate methods to use in the analysis of experimental data, we compared the different methods on simulations under three regularization schemes (Tikhonov, tSVD, and dSVD), three regularization parameter selection methods (NCP, L-curve, and GCV), and seven different a priori spatial smoothness constraints on the CSD distribution. This resulted in a comparison of 531 estimation schemes. We evaluated the estimation schemes according to their source reconstruction accuracy by testing them using different simulated noise levels, lateral source diameters, and CSD depth profiles. We found that ranking schemes according to the average error over all tested conditions results in a reproducible ranking, where the top schemes are found to perform well in the majority of tested conditions. However, there is no single best estimation scheme that outperforms all others under all tested

  6. Enhancing critical current density of cuprate superconductors

    Science.gov (United States)

    Chaudhari, Praveen

    2015-06-16

    The present invention concerns the enhancement of critical current densities in cuprate superconductors. Such enhancement of critical current densities include using wave function symmetry and restricting movement of Abrikosov (A) vortices, Josephson (J) vortices, or Abrikosov-Josephson (A-J) vortices by using the half integer vortices associated with d-wave symmetry present in the grain boundary.

  7. Program Calculates Current Densities Of Electronic Designs

    Science.gov (United States)

    Cox, Brian

    1996-01-01

    PDENSITY computer program calculates current densities for use in calculating power densities of electronic designs. Reads parts-list file for given design, file containing current required for each part, and file containing size of each part. For each part in design, program calculates current density in units of milliamperes per square inch. Written by use of AWK utility for Sun4-series computers running SunOS 4.x and IBM PC-series and compatible computers running MS-DOS. Sun version of program (NPO-19588). PC version of program (NPO-19171).

  8. Critical current densities in superconducting materials

    Indian Academy of Sciences (India)

    P Chaddah

    2003-02-01

    We discuss recent research in the area of critical current densities $(J_C)$ in superconductors. This shall cover recent work on newly discovered superconductors, as well as on the magnetic-field dependence of $J_C$.

  9. Burnout current density of bismuth nanowires

    Science.gov (United States)

    Cornelius, T. W.; Picht, O.; Müller, S.; Neumann, R.; Völklein, F.; Karim, S.; Duan, J. L.

    2008-05-01

    Single bismuth nanowires with diameters ranging from 100nmto1μm were electrochemically deposited in ion track-etched single-pore polycarbonate membranes. The maximum current density the wires are able to carry was investigated by ramping up the current until failure occurred. It increases by three to four orders of magnitude for nanowires embedded in the template compared to bulk bismuth and rises with diminishing diameter. Simulations show that the wires are heated up electrically to the melting temperature. Since the surface-to-volume ratio rises with diminishing diameter, thinner wires dissipate the heat more efficiently to the surrounding polymer matrix and, thus, can tolerate larger current densities.

  10. Effect of current density on the morphology of Zn electrodeposits

    Institute of Scientific and Technical Information of China (English)

    Ailing Fan; Wenhuai Tian; M. Kurosaki

    2004-01-01

    The effect of current density on the morphology of Zn electrodeposits prepared by a flow-channel cell was investigated by scanning electron microscopy (SEM). It was found that the morphology of Zn electrodeposits evolves from thin-layered hexagonal η-phase crystals to pyramidal η-phase particles with increasing the current density. The morphological evolution at various flow rates was also examined and the results show that the morphological evolution at a lower flow rate is more remarkable than that at a higher flow rate with increasing the current density. To reveal the mechanism of the morphological evolution in detail, the atomic configuration on both (0001)η and { 1100 }η planes under different current densities was investigated, it was noted that a specify current density could provide a good condition for the layered epitaxial growth of hexagonal η-phase.

  11. Current Trends in Higher Education Technology: Simulation

    Science.gov (United States)

    Damewood, Andrea M.

    2016-01-01

    This paper is focused on how technology in use changes over time, and the current trend of simulation technology as a supported classroom technology. Simulation-based training as a learning tool is discussed within the context of adult learning theories, as is the technology used and how today's higher education technology administrators support…

  12. Surface current density K: an introduction

    DEFF Research Database (Denmark)

    McAllister, Iain Wilson

    1991-01-01

    The author discusses the vector surface of current density K used in electrical insulation studies. K is related to the vector tangential electric field Kt at the surface of a body by the vector equation K=ΓE t where Γ represents the surface conductivity. The author derives a surface continuity...... equation that represents the boundary condition which the potential distributions in the adjoining media must fulfill. The volume current may be small in comparison to the surface current, and consequently in deriving the potential solutions the first term in this equation can sometimes be neglected....

  13. Geometric massive higher spins and current exchanges

    CERN Document Server

    Francia, Dario

    2008-01-01

    Generalised Fierz-Pauli mass terms allow to describe massive higher-spin fields on flat background by means of simple quadratic deformations of the corresponding geometric, massless Lagrangians. In this framework there is no need for auxiliary fields. We briefly review the construction in the bosonic case and study the interaction of these massive fields with external sources, computing the corresponding propagators. In the same fashion as for the massive graviton, but differently from theories where auxiliary fields are present, the structure of the current exchange is completely determined by the form of the mass term itself.

  14. Current Developments in Nuclear Density Functional Methods

    CERN Document Server

    Dobaczewski, J

    2010-01-01

    Density functional theory (DFT) became a universal approach to compute ground-state and excited configurations of many-electron systems held together by an external one-body potential in condensed-matter, atomic, and molecular physics. At present, the DFT strategy is also intensely studied and applied in the area of nuclear structure. The nuclear DFT, a natural extension of the self-consistent mean-field theory, is a tool of choice for computations of ground-state properties and low-lying excitations of medium-mass and heavy nuclei. Over the past thirty-odd years, a lot of experience was accumulated in implementing, adjusting, and using the density-functional methods in nuclei. This research direction is still extremely actively pursued. In particular, current developments concentrate on (i) attempts to improve the performance and precision delivered by the nuclear density-functional methods, (ii) derivations of density functionals from first principles rooted in the low-energy chromodynamics and effective th...

  15. Current Exchanges and Unconstrained Higher Spins

    CERN Document Server

    Francia, D; Sagnotti, A

    2007-01-01

    The (Fang-)Fronsdal formulation for free fully symmetric (spinor-) tensors rests on (gamma-)trace constraints on gauge fields and parameters. When these are relaxed, glimpses of the underlying geometry emerge: the field equations extend to non-local expressions involving the higher-spin curvatures, and with only a pair of additional fields an equivalent ``minimal'' local formulation is also possible. In this paper we complete the discussion of the ``minimal'' formulation for fully symmetric (spinor-) tensors, constructing one-parameter families of Lagrangians and extending them to (A)dS backgrounds. We then turn on external currents, that in this setting are subject to conventional conservation laws and, by a close scrutiny of current exchanges in the various formulations, we clarify the precise link between the local and non-local versions of the theory. To this end, we first show the equivalence of the constrained and unconstrained local formulations, and then identify a unique set of non-local Lagrangian e...

  16. Critical current density: Measurements vs. reality

    Science.gov (United States)

    Pan, A. V.; Golovchanskiy, I. A.; Fedoseev, S. A.

    2013-07-01

    Different experimental techniques are employed to evaluate the critical current density (Jc), namely transport current measurements and two different magnetisation measurements forming quasi-equilibrium and dynamic critical states. Our technique-dependent results for superconducting YBa2Cu3O7 (YBCO) film and MgB2 bulk samples show an extremely high sensitivity of Jc and associated interpretations, such as irreversibility fields and Kramer plots, which lose meaning without a universal approach. We propose such approach for YBCO films based on their unique pinning features. This approach allows us to accurately recalculate the magnetic-field-dependent Jc obtained by any technique into the Jc behaviour, which would have been measured by any other method without performing the corresponding experiments. We also discovered low-frequency-dependent phenomena, governing flux dynamics, but contradicting the considered ones in the literature. The understanding of these phenomena, relevant to applications with moving superconductors, can clarify their dramatic impact on the electric-field criterion through flux diffusivity and corresponding measurements.

  17. Current Density Measurements of an Annular-Geometry Ion Engine

    Science.gov (United States)

    Shastry, Rohit; Patterson, Michael J.; Herman, Daniel A.; Foster, John E.

    2012-01-01

    The concept of the annular-geometry ion engine, or AGI-Engine, has been shown to have many potential benefits when scaling electric propulsion technologies to higher power. However, the necessary asymmetric location of the discharge cathode away from thruster centerline could potentially lead to non-uniformities in the discharge not present in conventional geometry ion thrusters. In an effort to characterize the degree of this potential nonuniformity, a number of current density measurements were taken on a breadboard AGI-Engine. Fourteen button probes were used to measure the ion current density of the discharge along a perforated electrode that replaced the ion optics during conditions of simulated beam extraction. Three Faraday probes spaced apart in the vertical direction were also used in a separate test to interrogate the plume of the AGI-Engine during true beam extraction. It was determined that both the discharge and the plume of the AGI-Engine are highly uniform, with variations under most conditions limited to 10% of the average current density in the discharge and 5% of the average current density in the plume. Beam flatness parameter measured 30 mm from the ion optics ranged from 0.85 0.95, and overall uniformity was shown to generally increase with increasing discharge and beam currents. These measurements indicate that the plasma is highly uniform despite the asymmetric location of the discharge cathode.

  18. Extended Opacity Tables with Higher Temperature-Density-Frequency Resolution

    Science.gov (United States)

    Schillaci, Mark; Orban, Chris; Delahaye, Franck; Pinsonneault, Marc; Nahar, Sultana; Pradhan, Anil

    2015-05-01

    Theoretical models for plasma opacities underpin our understanding of radiation transport in many different astrophysical objects. These opacity models are also relevant to HEDP experiments such as ignition scale experiments on NIF. We present a significantly expanded set of opacity data from the widely utilized Opacity Project, and make these higher resolution data publicly available through OSU's portal with dropbox.com. This expanded data set is used to assess how accurate the interpolation of opacity data in temperature-density-frequency dimensions must be in order to adequately model the properties of most stellar types. These efforts are the beginning of a larger project to improve the theoretical opacity models in light of experimental results at the Sandia Z-pinch showing that the measured opacity of Iron disagrees strongly with all current models.

  19. Particle Image Velocimetry Study of Density Current Fronts

    Science.gov (United States)

    Martin, Juan Ezequiel

    2009-01-01

    Gravity currents are flows that occur when a horizontal density difference causes fluid to move under the action of gravity; density currents are a particular case, for which the scalar causing the density difference is conserved. Flows with a strong effect of the horizontal density difference, even if only partially driven by it--such as the…

  20. High current density cathode for electrorefining in molten electrolyte

    Science.gov (United States)

    Li, Shelly X.

    2010-06-29

    A high current density cathode for electrorefining in a molten electrolyte for the continuous production and collection of loose dendritic or powdery deposits. The high current density cathode eliminates the requirement for mechanical scraping and electrochemical stripping of the deposits from the cathode in an anode/cathode module. The high current density cathode comprises a perforated electrical insulated material coating such that the current density is up to 3 A/cm.sup.2.

  1. Morphology and Density Structure of Post-CME Current Sheets

    Science.gov (United States)

    Vrsnak, B.; Poletto, G.; Vujic, E.; Vourlidas, A.

    2009-01-01

    Eruption of a coronal mass ejection (CME) is believed to drag and open the coronal magnetic field, presumably leading to the formation of a large-scale current sheet and field relaxation by magnetic reconnection. This paper analyzes the physical characteristics of ray-like coronal features formed in the aftermath of CMEs, to confirm whether interpreting such phenomena in terms of a reconnecting current sheet is consistent with observations. Methods: The study focuses on UVCS/SOHO and LASCO/SOHO measurements of the ray width, density excess, and coronal velocity field as a function of the radial distance. The morphology of the rays implies that they are produced by Petschek-like reconnection in the large-scale current sheet formed in the wake of CME. The hypothesis is supported by the flow pattern, often showing outflows along the ray, and sometimes also inflows into the ray. The inferred inflow velocities range from 3 to 30 km/s, and are consistent with the narrow opening-angle of rays, which add up to a few degrees. The density of rays is an order of magnitude higher than in the ambient corona. The model results are consistent with the observations, revealing that the main cause of the density excess in rays is a transport of the dense plasma from lower to higher heights by the reconnection outflow.

  2. Numerical Simulation of Density Current Evolution in a Diverging Channel

    Directory of Open Access Journals (Sweden)

    Mitra Javan

    2012-01-01

    Full Text Available When a buoyant inflow of higher density enters a reservoir, it sinks below the ambient water and forms an underflow. Downstream of the plunge point, the flow becomes progressively diluted due to the fluid entrainment. This study seeks to explore the ability of 2D width-averaged unsteady Reynolds-averaged Navier-Stokes (RANS simulation approach for resolving density currents in an inclined diverging channel. 2D width-averaged unsteady RANS equations closed by a buoyancy-modified − turbulence model are integrated in time with a second-order fractional step approach coupled with a direct implicit method and discretized in space on a staggered mesh using a second-order accurate finite volume approach incorporating a high-resolution semi-Lagrangian technique for the convective terms. A series of 2D width-averaged unsteady simulations is carried out for density currents. Comparisons with the experimental measurements and the other numerical simulations show that the predictions of velocity and density field are with reasonable accuracy.

  3. Fermion N-representability for prescribed density and paramagnetic current density

    OpenAIRE

    Tellgren, Erik I; Kvaal, Simen; Helgaker, Trygve

    2014-01-01

    The $N$-representability problem is the problem of determining whether or not there exists $N$-particle states with some prescribed property. Here we report an affirmative solution to the fermion $N$-representability problem when both the density and paramagnetic current density are prescribed. This problem arises in current-density functional theory and is a generalization of the well-studied corresponding problem (only the density prescribed) in density functional theory. Given any density ...

  4. Current-voltage curve of a bipolar membrane at high current density

    NARCIS (Netherlands)

    Aritomi, T.; Boomgaard, van den Th.; Strathmann, H.

    1996-01-01

    The potential drop across a bipolar membrane was measured as a function of the applied current density. As a result, an inflection point was observed in the obtained current-voltage curve at high current density. This inflection point indicates that at high current densities water supply from outsid

  5. Current-voltage curve of a bipolar membrane at high current density

    NARCIS (Netherlands)

    Aritomi, T.; van den Boomgaard, Anthonie; Strathmann, H.

    1996-01-01

    The potential drop across a bipolar membrane was measured as a function of the applied current density. As a result, an inflection point was observed in the obtained current-voltage curve at high current density. This inflection point indicates that at high current densities water supply from

  6. Bifurcation of Vortex Density Current in Trapped Bose Condensates

    Institute of Scientific and Technical Information of China (English)

    XU Tao; ZHANG ShengLi

    2002-01-01

    Vortex density current in the Gross-Pitaevskii theory is studied. It is shown that the inner structure of the topological vortices can be classified by Brouwer degrees and Hopf indices of φ-mapping. The dynamical equations of vortex density current have been given. The bifurcation behavior at the critical points of the current is discussed in detail.

  7. Current Source Density Estimation for Single Neurons

    Directory of Open Access Journals (Sweden)

    Dorottya Cserpán

    2014-03-01

    Full Text Available Recent developments of multielectrode technology made it possible to measure the extracellular potential generated in the neural tissue with spatial precision on the order of tens of micrometers and on submillisecond time scale. Combining such measurements with imaging of single neurons within the studied tissue opens up new experimental possibilities for estimating distribution of current sources along a dendritic tree. In this work we show that if we are able to relate part of the recording of extracellular potential to a specific cell of known morphology we can estimate the spatiotemporal distribution of transmembrane currents along it. We present here an extension of the kernel CSD method (Potworowski et al., 2012 applicable in such case. We test it on several model neurons of progressively complicated morphologies from ball-and-stick to realistic, up to analysis of simulated neuron activity embedded in a substantial working network (Traub et al, 2005. We discuss the caveats and possibilities of this new approach.

  8. Higher-density dyadic wavelet transform and its application

    Science.gov (United States)

    Qin, Yi; Tang, Baoping; Wang, Jiaxu

    2010-04-01

    This paper proposes a higher-density dyadic wavelet transform with two generators, whose corresponding wavelet filters are band-pass and high-pass. The wavelet coefficients at each scale in this case have the same length as the signal. This leads to a new redundant dyadic wavelet transform, which is strictly shift invariant and further increases the sampling in the time dimension. We describe the definition of higher-density dyadic wavelet transform, and discuss the condition of perfect reconstruction of the signal from its wavelet coefficients. The fast implementation algorithm for the proposed transform is given as well. Compared with the higher-density discrete wavelet transform, the proposed transform is shift invariant. Applications into signal denoising indicate that the proposed wavelet transform has better denoising performance than other commonly used wavelet transforms. In the end, various typical wavelet transforms are applied to analyze the vibration signals of two faulty roller bearings, the results show that the proposed wavelet transform can more effectively extract the fault characteristics of the roller bearings than the other wavelet transforms.

  9. Projected current density comparison in tDCS block and smooth FE modeling.

    Science.gov (United States)

    Indahlastari, Aprinda; Chauhan, Munish; Sadleir, Rosalind J

    2016-08-01

    Current density distribution and projected current density calculation following transcranial direct current stimulation (tDCS) forward model in a human head were compared between two modeling pipelines: block and smooth. Block model was directly constructed from MRI voxel resolution and simulated in C. Smooth models underwent a boundary smoothing process by applying recursive Gaussian filters and simulated in COMSOL. Three smoothing levels were added to determine their effects on current density distribution compared to block models. Median current density percentage differences were calculated in anterior superior temporal gyrus (ASTG), hippocampus (HIP), inferior frontal gyrus (IFG), occipital lobes (OCC) and precentral gyrus (PRC) and normalized against a baseline value. A maximum of + 20% difference in median current density was found for three standard electrode montages: F3-RS, T7-T8 and Cz-Oz. Furthermore, median current density percentage differences in each montage target brain structures were found to be within + 7%. Higher levels of smoothing increased median current density percentage differences in T7-T8 and Cz-Oz target structures. However, while demonstrating similar trends in each montage, additional smoothing levels showed no clear relationship between their smoothing effects and calculated median current density in the five cortical structures. Finally, relative L2 error in reconstructed projected current density was found to be 17% and 21% for block and smooth pipelines, respectively. Overall, a block model workflow may be a more attractive alternative for simulating tDCS stimulation because involves a shorter modeling time and independence from commercial modeling platforms.

  10. High current density nanofilament cathodes for microwave amplifiers

    NARCIS (Netherlands)

    Schnell, J-P.; Minoux, E.; Gangloff, L.; Vincent, P.; Legagneux, P.; Dieumegard, D.; David, J.-F.; Peauger, F.; Hudanski, L.; Teo, K.B.K.; Lacerda, R.; Chhowalla, M.; Hasko, D.G.; Ahmed, H.; Amaratunga, G.A.J.; Milne, W.I.; Vila, L.; Dauginet-De Pra, L.; Demoustier-Champagne, S.; Ferain, E.; Legras, R.; Piraux, L.; Gröening, O.; Raedt, H. De; Michielsen, K.

    2004-01-01

    We study high current density nanofilament cathodes for microwave amplifiers. Two different types of aligned nanofilament array have been studied: first, metallic nanowires grown by electrodeposition into nanoporous templates at very low temperature (T

  11. Determining the Limiting Current Density of Vanadium Redox Flow Batteries

    Directory of Open Access Journals (Sweden)

    Jen-Yu Chen

    2014-09-01

    Full Text Available All-vanadium redox flow batteries (VRFBs are used as energy storage systems for intermittent renewable power sources. The performance of VRFBs depends on materials of key components and operating conditions, such as current density, electrolyte flow rate and electrolyte composition. Mass transfer overpotential is affected by the electrolyte flow rate and electrolyte composition, which is related to the limiting current density. In order to investigate the effect of operating conditions on mass transport overpotential, this study established a relationship between the limiting current density and operating conditions. First, electrolyte solutions with different states of charge were prepared and used for a single cell to obtain discharging polarization curves under various operating conditions. The experimental results were then analyzed and are discussed in this paper. Finally, this paper proposes a limiting current density as a function of operating conditions. The result helps predict the effect of operating condition on the cell performance in a mathematical model.

  12. Higher spin currents in the orthogonal coset theory

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Changhyun [Kyungpook National University, Department of Physics, Taegu (Korea, Republic of)

    2017-06-15

    In the coset model (D{sub N}{sup (1)} + D{sub N}{sup (1)}, D{sub N}{sup (1)}) at levels (k{sub 1}, k{sub 2}), the higher spin 4 current that contains the quartic WZW currents contracted with a completely symmetric SO(2N) invariant d tensor of rank 4 is obtained. The three-point functions with two scalars are obtained for any finite N and k{sub 2} with k{sub 1} = 1. They are determined also in the large N 't Hooft limit. When one of the levels is the dual Coxeter number of SO(2N), k{sub 1} = 2N - 2, the higher spin (7)/(2) current, which contains the septic adjoint fermions contracted with the above d tensor and the triple product of structure constants, is obtained from the operator product expansion (OPE) between the spin (3)/(2) current living in the N = 1 superconformal algebra and the above higher spin 4 current. The OPEs between the higher spin (7)/(2), 4 currents are described. For k{sub 1} = k{sub 2} = 2N - 2 where both levels are equal to the dual Coxeter number of SO(2N), the higher spin 3 current of U(1) charge (4)/(3), which contains the six products of spin (1)/(2) (two) adjoint fermions contracted with the product of the d tensor and two structure constants, is obtained. The corresponding N = 2 higher spin multiplet is determined by calculating the remaining higher spin (7)/(2), (7)/(2), 4 currents with the help of two spin (3)/(2) currents in the N = 2 superconformal algebra. The other N = 2 higher spin multiplet, whose U(1) charge is opposite to the one of the above N = 2 higher spin multiplet, is obtained. The OPE between these two N = 2 higher spin multiplets is also discussed. (orig.)

  13. Solid Oxide Electrolysis Cells: Degradation at High Current Densities

    DEFF Research Database (Denmark)

    Knibbe, Ruth; Traulsen, Marie Lund; Hauch, Anne;

    2010-01-01

    The degradation of Ni/yttria-stabilized zirconia (YSZ)-based solid oxide electrolysis cells operated at high current densities was studied. The degradation was examined at 850°C, at current densities of −1.0, −1.5, and −2.0 A/cm2, with a 50:50 (H2O:H2) gas supplied to the Ni/YSZ hydrogen electrode...

  14. DISCONTINUOUS FLOW OF TURBID DENSITY CURRENTS Ⅱ. INTERNAL HYDRAULIC JUMP

    Institute of Scientific and Technical Information of China (English)

    Jiahua FAN

    2005-01-01

    Traveling and stationary internal hydraulic jumps in density currents with positive or negative entrainment coefficients were analyzed based on simple assumptions. An expression of internal hydraulic jumps with entrainment coefficients was derived. Experimental data, published in literature, of stationary internal hydraulic jumps in turbid, thermal and saline density currents including measured values of water entrainment were used to compare with theory. Comparison was also made of traveling internal hydraulic jumps between measured data and theory.

  15. A high current density DC magnetohydrodynamic (MHD) micropump

    NARCIS (Netherlands)

    Homsy, Alexandra; Koster, Sander; Eijkel, Jan C.T.; Berg, van den Albert; Lucklum, F.; Verpoorte, E.; Rooij, de Nico F.

    2005-01-01

    This paper describes the working principle of a DC magnetohydrodynamic (MHD) micropump that can be operated at high DC current densities (J) in 75-µm-deep microfluidic channels without introducing gas bubbles into the pumping channel. The main design feature for current generation is a micromachined

  16. A high current density DC magnetohydrodynamic (MHD) micropump

    NARCIS (Netherlands)

    Homsy, A; Koster, Sander; Eijkel, JCT; van den Berg, A; Lucklum, F; Verpoorte, E; de Rooij, NF

    2005-01-01

    This paper describes the working principle of a DC magnetohydrodynamic (MHD) micropump that can be operated at high DC current densities (J) in 75-mu m-deep microfluidic channels without introducing gas bubbles into the pumping channel. The main design feature for current generation is a micromachin

  17. High current density sheet-like electron beam generator

    Science.gov (United States)

    Chow-Miller, Cora; Korevaar, Eric; Schuster, John

    Sheet electron beams are very desirable for coupling to the evanescent waves in small millimeter wave slow-wave circuits to achieve higher powers. In particular, they are critical for operation of the free-electron-laser-like Orotron. The program was a systematic effort to establish a solid technology base for such a sheet-like electron emitter system that will facilitate the detailed studies of beam propagation stability. Specifically, the effort involved the design and test of a novel electron gun using Lanthanum hexaboride (LaB6) as the thermionic cathode material. Three sets of experiments were performed to measure beam propagation as a function of collector current, beam voltage, and heating power. The design demonstrated its reliability by delivering 386.5 hours of operation throughout the weeks of experimentation. In addition, the cathode survived two venting and pump down cycles without being poisoned or losing its emission characteristics. A current density of 10.7 A/sq cm. was measured while operating at 50 W of ohmic heating power. Preliminary results indicate that the nearby presence of a metal plate can stabilize the beam.

  18. Estimation of current density distribution under electrodes for external defibrillation

    Directory of Open Access Journals (Sweden)

    Papazov Sava P

    2002-12-01

    Full Text Available Abstract Background Transthoracic defibrillation is the most common life-saving technique for the restoration of the heart rhythm of cardiac arrest victims. The procedure requires adequate application of large electrodes on the patient chest, to ensure low-resistance electrical contact. The current density distribution under the electrodes is non-uniform, leading to muscle contraction and pain, or risks of burning. The recent introduction of automatic external defibrillators and even wearable defibrillators, presents new demanding requirements for the structure of electrodes. Method and Results Using the pseudo-elliptic differential equation of Laplace type with appropriate boundary conditions and applying finite element method modeling, electrodes of various shapes and structure were studied. The non-uniformity of the current density distribution was shown to be moderately improved by adding a low resistivity layer between the metal and tissue and by a ring around the electrode perimeter. The inclusion of openings in long-term wearable electrodes additionally disturbs the current density profile. However, a number of small-size perforations may result in acceptable current density distribution. Conclusion The current density distribution non-uniformity of circular electrodes is about 30% less than that of square-shaped electrodes. The use of an interface layer of intermediate resistivity, comparable to that of the underlying tissues, and a high-resistivity perimeter ring, can further improve the distribution. The inclusion of skin aeration openings disturbs the current paths, but an appropriate selection of number and size provides a reasonable compromise.

  19. Casimir effect for scalar current densities in topologically nontrivial spaces

    Science.gov (United States)

    Bellucci, S.; Saharian, A. A.; Saharyan, N. A.

    2015-08-01

    We evaluate the Hadamard function and the vacuum expectation value (VEV) of the current density for a charged scalar field, induced by flat boundaries in spacetimes with an arbitrary number of toroidally compactified spatial dimensions. The field operator obeys the Robin conditions on the boundaries and quasiperiodicity conditions with general phases along compact dimensions. In addition, the presence of a constant gauge field is assumed. The latter induces Aharonov-Bohm-type effect on the VEVs. There is a region in the space of the parameters in Robin boundary conditions where the vacuum state becomes unstable. The stability condition depends on the lengths of compact dimensions and is less restrictive than that for background with trivial topology. The vacuum current density is a periodic function of the magnetic flux, enclosed by compact dimensions, with the period equal to the flux quantum. It is explicitly decomposed into the boundary-free and boundary-induced contributions. In sharp contrast to the VEVs of the field squared and the energy-momentum tensor, the current density does not contain surface divergences. Moreover, for Dirichlet condition it vanishes on the boundaries. The normal derivative of the current density on the boundaries vanish for both Dirichlet and Neumann conditions and is nonzero for general Robin conditions. When the separation between the plates is smaller than other length scales, the behavior of the current density is essentially different for non-Neumann and Neumann boundary conditions. In the former case, the total current density in the region between the plates tends to zero. For Neumann boundary condition on both plates, the current density is dominated by the interference part and is inversely proportional to the separation.

  20. Rf Gun with High-Current Density Field Emission Cathode

    Energy Technology Data Exchange (ETDEWEB)

    Jay L. Hirshfield

    2005-12-19

    High current-density field emission from an array of carbon nanotubes, with field-emission-transistor control, and with secondary electron channel multiplication in a ceramic facing structure, have been combined in a cold cathode for rf guns and diode guns. Electrodynamic and space-charge flow simulations were conducted to specify the cathode configuration and range of emission current density from the field emission cold cathode. Design of this cathode has been made for installation and testing in an existing S-band 2-1/2 cell rf gun. With emission control and modulation, and with current density in the range of 0.1-1 kA/cm2, this cathode could provide performance and long-life not enjoyed by other currently-available cathodes

  1. Superconducting toroidal field coil current densities for the TFCX

    Energy Technology Data Exchange (ETDEWEB)

    Kalsi, S.S.; Hooper, R.J.

    1985-04-01

    A major goal of the Tokamak Fusion Core Experiment (TFCX) study was to minimize the size of the device and achieve lowest cost. Two key factors influencing the size of the device employing superconducting magnets are toroidal field (TF) winding current density and its nuclear heat load withstand capability. Lower winding current density requires larger radial build of the winding pack. Likewise, lower allowable nuclear heating in the winding requires larger shield thickness between the plasma and coil. In order to achieve a low-cost device, it is essential to maximize the winding's current density and nuclear heating withhstand capability. To meet the above objective, the TFCX design specification adopted as goals a nominal winding current density of 3500 A/cm/sup 2/ with 10-T peak field at the winding and peak nuclear heat load limits of 1 MW/cm/sup 3/ for the nominal design and 50 MW/cm/sup 3/ for an advanced design. This study developed justification for these current density and nuclear heat load limits.

  2. Ionospheric midlatitude electric current density inferred from multiple magnetic satellites

    Science.gov (United States)

    Shore, R. M.; Whaler, K. A.; Macmillan, S.; Beggan, C.; Olsen, N.; Spain, T.; Aruliah, A.

    2013-09-01

    A method for inferring zonal electric current density in the mid-to-low latitude F region ionosphere is presented. We describe a method of using near-simultaneous overflights of the Ørsted and CHAMP satellites to define a closed circuit for an application of Ampère's integral law to magnetic data. Zonal current density from sources in only the region between the two satellites is estimated for the first time. Six years of mutually available vector magnetic data allows overlaps spanning the full 24 h range of local time twice. Solutions are computed on an event-by-event basis after correcting for estimates of main and crustal magnetic fields. Current density in the range ±0.1 μA/m2 is resolved, with the distribution of electric current largely matching known features such as the Appleton anomaly. The currents appear unmodulated at times of either high-negative Dst or high F10.7, which has implications for any future efforts to model their effects. We resolve persistent current intensifications between geomagnetic latitudes of 30 and 50° in the postmidnight, predawn sector, a region typically thought to be relatively free of electric currents. The cause of these unexpected intensifications remains an open issue. We compare our results with current density predictions made by the Coupled Thermosphere-Ionosphere-Plasmasphere model, a self-consistent, first-principles, three-dimensional numerical dynamic model of ionospheric composition and temperatures. This independent validation of our current density estimates highlights good agreement in the broad spatiotemporal trends we identify, which increases confidence in our results.

  3. Current drive at plasma densities required for thermonuclear reactors.

    Science.gov (United States)

    Cesario, R; Amicucci, L; Cardinali, A; Castaldo, C; Marinucci, M; Panaccione, L; Santini, F; Tudisco, O; Apicella, M L; Calabrò, G; Cianfarani, C; Frigione, D; Galli, A; Mazzitelli, G; Mazzotta, C; Pericoli, V; Schettini, G; Tuccillo, A A

    2010-08-10

    Progress in thermonuclear fusion energy research based on deuterium plasmas magnetically confined in toroidal tokamak devices requires the development of efficient current drive methods. Previous experiments have shown that plasma current can be driven effectively by externally launched radio frequency power coupled to lower hybrid plasma waves. However, at the high plasma densities required for fusion power plants, the coupled radio frequency power does not penetrate into the plasma core, possibly because of strong wave interactions with the plasma edge. Here we show experiments performed on FTU (Frascati Tokamak Upgrade) based on theoretical predictions that nonlinear interactions diminish when the peripheral plasma electron temperature is high, allowing significant wave penetration at high density. The results show that the coupled radio frequency power can penetrate into high-density plasmas due to weaker plasma edge effects, thus extending the effective range of lower hybrid current drive towards the domain relevant for fusion reactors.

  4. Scaling rules for critical current density in anisotropic biaxial superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yingxu, E-mail: yingxuli@swjtu.edu.cn [Applied Mechanics and Structure Safety Key Laboratory of Sichuan Province, School of Mechanics and Engineering, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Kang, Guozheng [Applied Mechanics and Structure Safety Key Laboratory of Sichuan Province, School of Mechanics and Engineering, Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Gao, Yuanwen, E-mail: ywgao@lzu.edu.cn [Key Laboratory of Mechanics on Environment and Disaster in Western China, The Ministry of Education of China, Lanzhou, Gansu 730000 (China); Department of Mechanics and Engineering Science, College of Civil Engineering and Mechanics, Lanzhou University, Lanzhou, Gansu 730000 (China)

    2016-06-15

    Recent researches highlight the additional anisotropic crystallographic axis within the superconducting plane of high temperature superconductors (HTS), demonstrating the superconducting anisotropy of HTS is better understood in the biaxial frame than the previous uniaxial coordinates within the superconducting layer. To quantitatively evaluate the anisotropy of flux pinning and critical current density in HTS, we extend the scaling rule for single-vortex collective pinning in uniaxial superconductors to account for flux-bundle collective pinning in biaxial superconductors. The scaling results show that in a system of random uncorrected point defects, the field dependence of the critical current density is described by a unified function with the scaled magnetic field of the isotropic superconductor. The obtained angular dependence of the critical current density depicts the main features of experimental observations, considering possible corrections due to the strong-pinning interaction.

  5. Anodic Oxidation of Carbon Steel at High Current Densities and Investigation of Its Corrosion Behavior

    Science.gov (United States)

    Fattah-Alhosseini, Arash; Khan, Hamid Yazdani

    2017-02-01

    This work aims at studying the influence of high current densities on the anodization of carbon steel. Anodic protective coatings were prepared on carbon steel at current densities of 100, 125, and 150 A/dm2 followed by a final heat treatment. Coatings microstructures and morphologies were analyzed using X-ray diffraction (XRD) and scanning electron microscope (SEM). The corrosion resistance of the uncoated carbon steel substrate and the anodic coatings were evaluated in 3.5 wt pct NaCl solution through electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. The results showed that the anodic oxide coatings which were prepared at higher current densities had thicker coatings as a result of a higher anodic forming voltage. Therefore, the anodized coatings showed better anti-corrosion properties compared to those obtained at lower current densities and the base metal.

  6. High-density turbidity currents: Are they sandy debris flows?

    Energy Technology Data Exchange (ETDEWEB)

    Shanmugam, G. [Mobil Exploration and Producing Technical Center, Dallas, TX (United States)

    1996-01-01

    Conventionally, turbidity currents are considered as fluidal flows in which sediment is supported by fluid turbulence, whereas debris flows are plastic flows in which sediment is supported by matrix strength, dispersive pressure, and buoyant lift. The concept of high-density turbidity current refers to high-concentration, commonly non-turbulent, flows of fluids in which sediment is supported mainly by matrix strength, dispersive pressure, and buoyant lift. The conventional wisdom that traction carpets with entrained turbulent clouds on top represent high-density turbidity currents is a misnomer because traction carpets are neither fluidal nor turbulent. Debris flows may also have entrained turbulent clouds on top. The traction carpet/debris flow and the overriding turbulent clouds are two separate entities in terms of flow rheology and sediment-support mechanism. In experimental and theoretical studies, which has linked massive sands and floating clasts to high-density turbidity currents, the term high-density turbidity current has actually been used for laminar flows. In alleviating this conceptual problem, sandy debris flow is suggested as a substitute for high-density turbidity current. Sandy debris flows represent a continuous spectrum of processes between cohesive and cohesionless debris flows. Commonly they are rheologically plastic. They may occur with or without entrained turbulent clouds on top. Their sediment-support mechanisms include matrix strength, dispersive pressure, and buoyant lift. They are characterized by laminar flow conditions, a moderate to high grain concentration, and a low to moderate mud content. Although flows evolve and transform during the course of transport in density-stratified flows, the preserved features in a deposit are useful to decipher only the final stages of deposition. At present, there are no established criteria to decipher transport mechanism from the depositional record.

  7. Estimation of current density distribution of PAFC by analysis of cell exhaust gas

    Energy Technology Data Exchange (ETDEWEB)

    Kato, S.; Seya, A. [Fuji Electric Co., Ltd., Ichihara-shi (Japan); Asano, A. [Fuji Electric Corporate, Ltd., Yokosuka-shi (Japan)

    1996-12-31

    To estimate distributions of Current densities, voltages, gas concentrations, etc., in phosphoric acid fuel cell (PAFC) stacks, is very important for getting fuel cells with higher quality. In this work, we leave developed a numerical simulation tool to map out the distribution in a PAFC stack. And especially to Study Current density distribution in the reaction area of the cell, we analyzed gas composition in several positions inside a gas outlet manifold of the PAFC stack. Comparing these measured data with calculated data, the current density distribution in a cell plane calculated by the simulation, was certified.

  8. Engineering Critical Current Density Improvement in Ag- Bi-2223 Tapes

    DEFF Research Database (Denmark)

    Wang, W. G.; Seifi, Behrouz; Eriksen, Morten;

    2000-01-01

    Ag alloy sheathed Bi-2223 multifilament tapes were produced by the powder-in-tube method. Engineering critical current density improvement has been achieved through both enhancement of critical current density by control of the thermal behavior of oxide powder and by an increase of the filling...... the superconductor composite sustaining large proportional oxide ceramics in the composite during drawing and rolling process. By optimization of the thermal and mechanical process, a Je of 12 kA/cm2 has been achieved in a 0.183.1 mm2 size tape which carried 67 A...

  9. Current Density Imaging through Acoustically Encoded Magnetometry: A Theoretical Exploration

    CERN Document Server

    Sheltraw, Daniel J

    2014-01-01

    The problem of determining a current density confined to a volume from measurements of the magnetic field it produces exterior to that volume is known to have non-unique solutions. To uniquely determine the current density, or the non-silent components of it, additional spatial encoding of the electric current is needed. In biological systems such as the brain and heart, which generate electric current associated with normal function, a reliable means of generating such additional encoding, on a spatial and temporal scale meaningful to the study of such systems, would be a boon for research. This paper explores a speculative method by which the required additional encoding might be accomplished, on the time scale associated with the propagation of sound across the volume of interest, by means of the application of a radially encoding pulsed acoustic spherical wave.

  10. Higher Spin Fields in Siegel Space, Currents and Theta Functions

    CERN Document Server

    Gelfond, O A

    2009-01-01

    Dynamics of four-dimensional massless fields of all spins is formulated in the Siegel space of complex $4\\times 4$ symmetric matrices. It is shown that the unfolded equations of free massless fields, that have a form of multidimensional Schrodinger equations, naturally distinguish between positive- and negative-frequency solutions of relativistic field equations, i.e. particles and antiparticles. Multidimensional Riemann theta functions are shown to solve massless field equations in the Siegel space. We establish the correspondence between conserved higher-spin currents in four-dimensional Minkowski space and those in the ten-dimensional matrix space. It is shown that global symmetry parameters of the current in the matrix space should be singular to reproduce a nonzero current in Minkowski space. The $\\D$-function integral evolution formulae for 4d massless fields in the Fock-Siegel space are obtained. The generalization of the proposed scheme to higher dimensions and systems of higher ranks is considered.

  11. High current density stability of ohmic contacts to silicon carbide

    Science.gov (United States)

    Downey, Brian P.

    The materials properties of SiC, such as wide bandgap, high breakdown electric field, and good thermal conductivity, make it an appealing option for high temperature and high power applications. The replacement of Si devices with SiC components could lead to a reduction in device size, weight, complexity, and cooling requirements along with an increase in device efficiency. One area of concern under high temperature or high current operation is the stability of the ohmic contacts. Ohmic contact degradation can cause an increase in parasitic resistance, which can diminish device performance. While contact studies have primarily focused on the high temperature stability of ohmic contacts to SiC, different failure mechanisms may arise under high current density stressing due to the influence of electromigration. In addition, preferential degradation may occur at the anode or cathode due to the directionality of current flow, known as a polarity effect. The failure mechanisms of ohmic contacts to p-type SiC under high current density stressing are explored. Complementary materials characterization techniques were used to analyze contact degradation, particularly the use of cross-sections prepared by focused ion beam for imaging using field emission scanning electron microscopy and elemental analysis using Auger electron spectroscopy. Initially the degradation of commonly studied Ni and Al-based contacts was investigated under continuous DC current. The contact metallization included a bond pad consisting of a TiW diffusion barrier and thick Au overlayer. The Ni contacts were found to degrade due to the growth of voids within the ohmic contact layer, which were initially produced during the high temperature Ni/SiC ohmic contact anneal. The Al-based contacts degraded due to the movement of Al from the ohmic contact layer to the surface of the Au bond pad, and the movement of Au into the ohmic contact layer from the bond pad. The inequality of Al and Au fluxes generated

  12. Path to Efficient Lower Hybrid Current Drive at High Density

    Science.gov (United States)

    Baek, S. G.; Bonoli, P. T.; Brunner, D.; Faust, I.; Labombard, B. L.; Parker, R. R.; Shiraiwa, S.; Wallace, G. M.; Wukitch, S.

    2015-11-01

    Recovery of lower hybrid current drive (LHCD) efficiency at high density was demonstrated on Alcator C-Mod by modifying the scrape-off layer (SOL) plasma. RF probe measurements around the C-Mod tokamak indicate that the LH wave amplitude at the high field side wall significantly attenuates with plasma density. This is interpreted as enhanced collisional loss due to the increase in the SOL density and width. By taking advantage of the narrower SOL width by doubling plasma current to 1.1 MA, it is found that the LH wave amplitude maintains its strength, and an effective current drive is extended to above 1x10e20 m-3. An order of magnitude increase in non-thermal Bremsstrahlung emission is consistent with ray-tracing results which take into account the change of SOL profiles with current. In the coming campaign, a further investigation on the role of the SOL plasma is planned by raising plasma current above 1.1 MA. This will be aided with newly developed RF magnetic loop antennas mounted on a radially movable probe head. This system is expected to intercept the LH resonance cone on the first pass, allowing us to measure radial profiles of both the wave amplitude and dominant parallel wavenumber in the SOL for the first time. These data will be compared with the GENRAY ray-tracing code. Work supported by USDoE awards DE-FC02-99ER54512.

  13. Ionospheric midlatitude electric current density inferred from multiple magnetic satellites

    DEFF Research Database (Denmark)

    Shore, R. M.; Whaler, K. A.; Macmillan, S.

    2013-01-01

    A method for inferring zonal electric current density in the mid-to-low latitude F region ionosphere is presented. We describe a method of using near-simultaneous overflights of the Ørsted and CHAMP satellites to define a closed circuit for an application of Ampère's integral law to magnetic data....... Zonal current density from sources in only the region between the two satellites is estimated for the first time. Six years of mutually available vector magnetic data allows overlaps spanning the full 24 h range of local time twice. Solutions are computed on an event-by-event basis after correcting...... for estimates of main and crustal magnetic fields. Current density in the range ±0.1 μA/m2 is resolved, with the distribution of electric current largely matching known features such as the Appleton anomaly. The currents appear unmodulated at times of either high-negative Dst or high F10.7, which has...

  14. The density matrix picture of laser coherent control current

    Institute of Scientific and Technical Information of China (English)

    SHOU Qian; ZHANG Haichao; LIU Luning; LIN Weizhu

    2004-01-01

    The physical substance of the coherent control current and the optical rectification have been analyzed based on density matrix perturbation theory. The analytical results demonstrate that they arise from the real and virtual manifestations of the same nonlinear process associated with diagonal and non-diagonal density matrix.And in terms of polarization, they respectively arise from the intraband and interband polarizations. Both the evolution of the coherent control current exited by ultrafast laser pulse and its dependence on frequency have been studied in time and frequency domains. In order to get an explicit knowledge of intraband polarization and the origination of the coherent control current, we have investigated the initial photo-carriers momentum distribution. The ultrafast decay of the polar momentum population in order of tens of femtosends is given to illustrate its instantaneous optical response.

  15. The Current State of Marketing Activity among Higher Education Institutions.

    Science.gov (United States)

    Newman, Cynthia M.

    2002-01-01

    Investigated the current state of marketing, marketing research, and planning practices at four-year higher education institutions. Builds upon previous studies by Blackburn (1979) and Goldgehn (1982 and 1989). Determined whether the use and apparent understanding of marketing and its attendant activities by admissions and enrollment management…

  16. Current Issues for Higher Education Information Resources Management.

    Science.gov (United States)

    CAUSE/EFFECT, 1995

    1995-01-01

    Current issues that are important for the future of information resources management in higher education are presented. They include: integrating planning for information resources within institution-wide strategic planning; reengineering fundamental services; change management; distributed computing support; networking; the changing communication…

  17. Massive fermion model in 3d and higher spin currents

    CERN Document Server

    Bonora, L; Prester, P Dominis; de Souza, B Lima; Smolic, I

    2016-01-01

    We analyze the 3d free massive fermion theory coupled to external sources. The presence of a mass explicitly breaks parity invariance. We calculate two- and three-point functions of a gauge current and the energy momentum tensor and, for instance, obtain the well-known result that in the IR limit (but also in the UV one) we reconstruct the relevant CS action. We then couple the model to higher spin currents and explicitly work out the spin 3 case. In the UV limit we obtain an effective action which was proposed many years ago as a possible generalization of spin 3 CS action. In the IR limit we derive a different higher spin action. This analysis can evidently be generalized to higher spins. We also discuss the conservation and properties of the correlators we obtain in the intermediate steps of our derivation.

  18. High dislocation density of tin induced by electric current

    Energy Technology Data Exchange (ETDEWEB)

    Liao, Yi-Han; Liang, Chien-Lung; Lin, Kwang-Lung, E-mail: matkllin@mail.ncku.edu.tw [Department of Material Science and Engineering, National Cheng Kung University, Tainan 70101, Taiwan, R. O. C (China); Wu, Albert T. [Department of Chemical and Material Engineering, National Central University, Jhongli 32001, Taiwan, R. O. C (China)

    2015-12-15

    A dislocation density of as high as 10{sup 17} /m{sup 2} in a tin strip, as revealed by high resolution transmission electron microscope, was induced by current stressing at 6.5 x 10{sup 3} A/ cm{sup 2}. The dislocations exist in terms of dislocation line, dislocation loop, and dislocation aggregates. Electron Backscattered Diffraction images reflect that the high dislocation density induced the formation of low deflection angle subgrains, high deflection angle Widmanstätten grains, and recrystallization. The recrystallization gave rise to grain refining.

  19. Higher-spin current multiplets in operator-product expansions

    CERN Document Server

    Anselmi, D

    2000-01-01

    Various formulas for currents with arbitrary spin are worked out in general space-time dimension, in the free field limit and, at the bare level, in presence of interactions. As the n-dimensional generalization of the (conformal) vector field, the (n/2-1)-form is used. The two-point functions and the higher-spin central charges are evaluated at one loop. As an application, the higher-spin hierarchies generated by the stress-tensor operator-product expansion are computed in supersymmetric theories. The results exhibit an interesting universality.

  20. Casimir effect for scalar current densities in topologically nontrivial spaces

    CERN Document Server

    Bellucci, S; Saharyan, N A

    2015-01-01

    We evaluate the Hadamard function and the vacuum expectation value (VEV) of the current density for a charged scalar field, induced by flat boundaries in spacetimes with an arbitrary number of toroidally compactified spatial dimensions. The field operator obeys the Robin conditions on the boundaries and quasiperiodicity conditions with general phases along compact dimensions. In addition, the presence of a constant gauge field is assumed. The latter induces Aharonov-Bohm-type effect on the VEVs. There is a region in the space of the parameters in Robin boundary conditions where the vacuum state becomes unstable. The stability condition depends on the lengths of compact dimensions and is less restrictive than that for background with trivial topology. The vacuum current density is a periodic function of the magnetic flux, enclosed by compact dimensions, with the period equal to the flux quantum. It is explicitly decomposed into the boundary-free and boundary-induced contributions. In sharp contrast to the VEVs...

  1. Magnetic topology and current channels in plasmas with toroidal current density inversions

    Science.gov (United States)

    Ciro, D.; Caldas, I. L.

    2013-10-01

    The equilibrium magnetic field inside axisymmetric plasmas with inversions on the toroidal current density is considered. Previous works have shown that internal regions with negative current density lead to non-nested magnetic surfaces inside the plasma. Following these results, we derive a general expression relating the positive and negative currents inside the non-nested surfaces. This is done in terms of an anisotropy parameter that is model-independent and is based in very general properties of the magnetic field. We demonstrate that the positive currents in axisymmetric islands screen the negative one in the plasma center by reaching about twice its magnitude. Further, we illustrate these results by developing a family of analytical local solutions for the poloidal magnetic field in a region of interest that contains the inverted current. These local solutions exhibit non-nested magnetic surfaces with a combined current of at least twice the magnitude of the negative one, as prescribed from the topological arguments, and allow to study topological transitions driven by geometrical changes in the current profile. To conclude, we discuss the signatures of internal current density inversions in a confinement device and show that magnetic pitch measurements may be inappropriate to differentiate current reversals and small current holes in plasmas.

  2. Higher insulin sensitivity in vegans is not associated with higher mitochondrial density.

    Science.gov (United States)

    Gojda, J; Patková, J; Jaček, M; Potočková, J; Trnka, J; Kraml, P; Anděl, M

    2013-12-01

    Vegans have a lower incidence of insulin resistance (IR)-associated diseases and a higher insulin sensitivity (IS) compared with omnivores. The aim of this study was to examine whether the higher IS in vegans relates to markers of mitochondrial biogenesis and to intramyocellular lipid (IMCL) content. Eleven vegans and 10 matched (race, age, sex, body mass index, physical activity and energy intake) omnivorous controls were enrolled in a case-control study. Anthropometry, bioimpedance (BIA), ultrasound measurement of visceral and subcutaneous fat layer, parameters of glucose and lipid homeostasis, hyperinsulinemic euglycemic clamp and muscle biopsies were performed. Citrate synthase (CS) activity, mitochondrial DNA (mtDNA) and IMCL content were assessed in skeletal muscle samples. Both groups were comparable in anthropometric and BIA parameters, physical activity and protein-energy intake. Vegans had significantly higher glucose disposal (M-value, vegans 8.11±1.51 vs controls 6.31±1.57 mg/kg/min, 95% confidence interval: 0.402 to 3.212, P=0.014), slightly lower IMCL content (vegans 13.91 (7.8 to 44.0) vs controls 17.36 (12.4 to 78.5) mg/g of muscle, 95% confidence interval: -7.594 to 24.550, P=0.193) and slightly higher relative muscle mtDNA amount (vegans 1.36±0.31 vs controls 1.13±0.36, 95% confidence interval:-0.078 to 0.537, P=0.135). No significant differences were found in CS activity (vegans 18.43±5.05 vs controls 18.16±5.41 μmol/g/min, 95% confidence interval: -4.503 to 5.050, P=0.906). Vegans have a higher IS, but comparable mitochondrial density and IMCL content with omnivores. This suggests that a decrease in whole-body glucose disposal may precede muscle lipid accumulation and mitochondrial dysfunction in IR development.

  3. Magnetohydrodynamically stable plasma with supercritical current density at the axis

    Energy Technology Data Exchange (ETDEWEB)

    Burdakov, A. V. [Budker Institute of Nuclear Physics, 11 Lavrentjev Avenue, 630090 Novosibirsk (Russian Federation); Novosibirsk State Technical University, 20 Karl Marks Avenue, 630092 Novosibirsk (Russian Federation); Postupaev, V. V., E-mail: V.V.Postupaev@inp.nsk.su; Sudnikov, A. V. [Budker Institute of Nuclear Physics, 11 Lavrentjev Avenue, 630090 Novosibirsk (Russian Federation); Novosibirsk State University, 2 Pirogova st., 630090 Novosibirsk (Russian Federation)

    2014-05-15

    In this work, an analysis of magnetic perturbations in the GOL-3 experiment is given. In GOL-3, plasma is collectively heated in a multiple-mirror trap by a high-power electron beam. During the beam injection, the beam-plasma interaction maintains a high-level microturbulence. This provides an unusual radial profile of the net current (that consists of the beam current, current of the preliminary discharge, and the return current). The plasma core carries supercritical current density with the safety factor well below unity, but as a whole, the plasma is stable with q(a) ≈ 4. The net plasma current is counter-directed to the beam current; helicities of the magnetic field in the core and at the edge are of different signs. This forms a system with a strong magnetic shear that stabilizes the plasma core in good confinement regimes. We have found that the most pronounced magnetic perturbation is the well-known n = 1, m = 1 mode for both stable and disruptive regimes.

  4. Higher-accuracy van der Waals density functional

    DEFF Research Database (Denmark)

    Lee, Kyuho; Murray, Éamonn D.; Kong, Lingzhu

    2010-01-01

    We propose a second version of the van der Waals density functional of Dion et al. [Phys. Rev. Lett. 92, 246401 (2004)], employing a more accurate semilocal exchange functional and the use of a large-N asymptote gradient correction in determining the vdW kernel. The predicted binding energy...

  5. Effect of coating current density on the wettability of electrodeposited copper thin film on aluminum substrate

    Directory of Open Access Journals (Sweden)

    Arun Augustin

    2016-09-01

    Full Text Available Copper is the only one solid metal registered by the US Environmental Protection Agency as an antimicrobial touch surface. In touch surface applications, wettability of the surface has high significance. The killing rate of the harmful microbes depends on the wetting of pathogenic solution. Compared to the bulk copper, coated one on aluminum has the advantage of economic competitiveness and the possibility of manufacturing complex shapes. In the present work, the copper coating on the aluminum surface has successfully carried out by electrodeposition using non cyanide alkaline bath. To ensure good adhesion strength, the substrate has been pre-zincated prior to copper deposition. The coating current density is one of the important parameters which determine the nucleation density of the copper on the substrate. To understand the effect of current density on wettability, the coating has done at different current densities in the range of 3 A dm−2 to 9 A dm−2 for fixed time interval. The grain size has been measured from TEM micrographs and showed that as current density increases, grain size reduces from 62 nm to 35 nm. Since the grain size reduces, grain boundary volume has increases. As a result the value of strain energy (calculated by Williamson–Hall method has increased. The density of nodular morphology observed in SEM analysis has been increased with coating current density. Further, wettability studies with respect to double distilled water on the electrodeposited copper coatings which are coated at different current densities are carried out. At higher current density the coating is more wettable by water because at these conditions grain size of the coating decreases and morphology of grain changes to a favorable dense nodularity.

  6. Stochastic Time-Dependent Current-Density Functional Theory

    Science.gov (United States)

    D'Agosta, Roberto

    2008-03-01

    Static and dynamical density functional methods have been applied with a certain degree of success to a variety of closed quantum mechanical systems, i.e., systems that can be described via a Hamiltonian dynamics. However, the relevance of open quantum systems - those coupled to external environments, e.g., baths or reservoirs - cannot be overestimated. To investigate open quantum systems with DFT methods we have introduced a new theory, we have named Stochastic Time-Dependent Current Density Functional theory (S-TDCDFT) [1]: starting from a suitable description of the system dynamics via a stochastic Schrödinger equation [2], we have proven that given an initial quantum state and the coupling between the system and the environment, there is a one-to-one correspondence between the ensemble-averaged current density and the external vector potential applied to the system.In this talk, I will introduce the stochastic formalism needed for the description of open quantum systems, discuss in details the theorem of Stochastic TD-CDFT, and provide few examples of its applicability like the dissipative dynamics of excited systems, quantum-measurement theory and other applications relevant to charge and energy transport in nanoscale systems.[1] M. Di Ventra and R. D'Agosta, Physical Review Letters 98, 226403 (2007)[2] N.G. van Kampen, Stochastic processes in Physics and Chemistry, (North Holland, 2001), 2nd ed.

  7. High current densities enable exoelectrogens to outcompete aerobic heterotrophs for substrate

    KAUST Repository

    Ren, Lijiao

    2014-08-05

    © 2014 Wiley Periodicals, Inc. Chemical oxygen demand (COD) removal rates could be described by first-order kinetics with respect to COD concentration at different current densities, even under open circuit conditions with no current generation. The COD concentration was reduced more quickly with current generation due to the greater consumption of substrate by exoelectrogens, and less substrate was lost to aerobic heterotrophs. Higher current densities enabled exoelectrogens to outcompete aerobic heterotrophs for substrate, allowing for increased coulombic efficiencies with current densities. © 2014 Wiley Periodicals, Inc. In mixed-culture microbial fuel cells (MFCs), exoelectrogens and other microorganisms compete for substrate. It has previously been assumed that substrate losses to other terminal electron acceptors over a fed-batch cycle, such as dissolved oxygen, are constant. However, a constant rate of substrate loss would only explain small increases in coulombic efficiencies (CEs, the fraction of substrate recovered as electrical current) with shorter cycle times, but not the large increases in CE that are usually observed with higher current densities and reduced cycle times. To better understand changes in CEs, COD concentrations were measured over time in fed-batch, single-chamber, air-cathode MFCs at different current densities (external resistances). COD degradation rates were all found to be first-order with respect to COD concentration, even under open circuit conditions with no current generation (first-order rate constant of 0.14±0.01h-1). The rate of COD removal increased when there was current generation, with the highest rate constant (0.33±0.02h-1) obtained at the lowest external resistance (100Ω). Therefore, as the substrate concentration was reduced more quickly due to current generation, the rate of loss of substrate to non-exoelectrogens decreased due to this first-order substrate-concentration dependence. As a result, coulombic

  8. Smoothness of invariant density for expanding transformations in higher dimensions

    Directory of Open Access Journals (Sweden)

    Kourosh Adl-Zarabi

    2000-01-01

    Full Text Available Let Ω be a bounded region in ℝn and let ={Pi}i=1m be a partition of Ω into a finite number of closed subsets having piecewise C2 boundaries of finite (n−1-dimensional measure. Let τ:Ω→Ω be an expanding transformation on where, τi:τ|Pi, and τi∈CM, m≥2. We show that the τ-invariant density h∈CM−2.

  9. Measurement of local current density of all-vanadium redox flow batteries

    Science.gov (United States)

    Hsieh, Wen-Yen; Leu, Chih-Hsing; Wu, Chun-Hsing; Chen, Yong-Song

    2014-12-01

    This article presents a preliminary study of the measurement of local current density in all-vanadium redox flow batteries. Two batteries are designed and manufactured in this study, and the experimental results are compared. In the first cell, the current collector is divided into 25 segments, and the flow field plate is not segmented, whereas in the other cell, the flow field plate is segmented. The effects of the electrolyte flow rate on the battery efficiencies and the local current density variation are investigated. The experimental results show that the current density near the outlet significantly decreases when the discharge capacity approaches zero. In addition, the battery has a larger discharge depth at a higher electrolyte flow rate.

  10. High Current Density 2D/3D Esaki Tunnel Diodes

    CERN Document Server

    Krishnamoorthy, Sriram; Lee, Choong Hee; Zhang, Yuewei; McCulloch, William D; Johnson, Jared M; Hwang, Jinwoo; Wu, Yiying; Rajan, Siddharth

    2016-01-01

    The integration of two-dimensional materials such as transition metal dichalcogenides with bulk semiconductors offer interesting opportunities for 2D/3D heterojunction-based novel device structures without any constraints of lattice matching. By exploiting the favorable band alignment at the GaN/MoS2 heterojunction, an Esaki interband tunnel diode is demonstrated by transferring large area, Nb-doped, p-type MoS2 onto heavily n-doped GaN. A peak current density of 446 A/cm2 with repeatable room temperature negative differential resistance, peak to valley current ratio of 1.2, and minimal hysteresis was measured in the MoS2/GaN non-epitaxial tunnel diode. A high current density of 1 kA/cm2 was measured in the Zener mode (reverse bias) at -1 V bias. The GaN/MoS2 tunnel junction was also modeled by treating MoS2 as a bulk semiconductor, and the electrostatics at the 2D/3D interface was found to be crucial in explaining the experimentally observed device characteristics.

  11. Emergent loop current order from pair density wave superconductivity

    Science.gov (United States)

    Kashyap, Manoj; Melchert, Drew; Agterberg, Daniel

    2015-03-01

    In addition to charge density wave (CDW) order, there is evidence that the pseudogap phase in the cuprates breaks time reversal symmetry. Here we show that pair density wave (PDW) states give rise to a translational invariant non-superconducting order parameter that breaks time reversal and parity symmetries, but preserves their product. This secondary order parameter has a different origin, but shares the same symmetry properties as a magnetoelectric loop current order that has been proposed earlier in the context of the cuprates to explain the appearance of intra-cell magnetic order. We further show that, due to fluctuations, this secondary loop current order, which represents the breaking of discrete symmetries, can preempt PDW order, which breaks both continuous and discrete symmetries. In such a phase, the emergent loop current order coexists with spatial short range CDW and short range superconducting order. Finally, we propose a PDW phase that accounts for intra-cell magnetic order and the Kerr effect, has CDW order consistent with x-ray scattering and nuclear magnetic resonance observations, and quasi-particle properties consistent with angle resolved photoemission scattering. We acknowledge support from NSF Grant No. DMR-1335215

  12. Anomalous dimensions of higher spin currents in large N CFTs

    CERN Document Server

    Hikida, Yasuaki

    2016-01-01

    We examine anomalous dimensions of higher spin currents in the critical O(N) scalar model and the Gross-Neveu model in arbitrary d dimensions. These two models are proposed to be dual to the type A and type B Vasiliev theories, respectively. We reproduce the known results on the anomalous dimensions to the leading order in 1/N by using conformal perturbation theory. This work can be regarded as an extension of previous work on the critical O(N) scalars in 3 dimensions, where it was shown that the bulk computation for the masses of higher spin fields on AdS_4 can be mapped to the boundary one in conformal perturbation theory. The anomalous dimensions of the both theories agree with each other up to an overall factor depending only on d, and the coincidence is explained for d=3 by making use of N=2 supersymmetry.

  13. The current density in quantum electrodynamics in external potentials

    Energy Technology Data Exchange (ETDEWEB)

    Schlemmer, Jan, E-mail: jan.schlemmer@univie.ac.at [Fakultät für Physik, Universität Wien, Boltzmanngasse 5, 1090 Wien (Austria); Zahn, Jochen, E-mail: jochen.zahn@itp.uni-leipzig.de [Institut für Theoretische Physik, Universität Leipzig, Brüderstr. 16, 04103 Leipzig (Germany)

    2015-08-15

    We review different definitions of the current density for quantized fermions in the presence of an external electromagnetic field. Several deficiencies in the popular prescription due to Schwinger and the mode sum formula for static external potentials are pointed out. We argue that Dirac’s method, which is the analog of the Hadamard point-splitting employed in quantum field theory in curved space–times, is conceptually the most satisfactory. As a concrete example, we discuss vacuum polarization and the stress–energy tensor for massless fermions in 1+1 dimension. Also a general formula for the vacuum polarization in static external potentials in 3+1 dimensions is derived.

  14. Discretizing Transient Current Densities in the Maxwell Equations

    Energy Technology Data Exchange (ETDEWEB)

    Stowell, M L

    2008-11-25

    We will briefly discuss a technique for applying transient volumetric current sources in full-wave, time-domain electromagnetic simulations which avoids the need for divergence cleaning. The method involves both 'edge-elements' and 'face-elements' in conjunction with a particle-in-cell scheme to track the charge density. Results from a realistic, 6.7 million element, 3D simulation are shown. While the author may have a finite element bias the technique should be applicable to finite difference methods as well.

  15. On the theory of the electric field and current density in a superconductor carrying transport current

    Energy Technology Data Exchange (ETDEWEB)

    Carr, W.J. [LEI 700 Technology Dr., Pittsburgh, PA 15219 (United States)]. E-mail: wjamescarrjr@att.net

    2005-09-15

    A theory is given to explain the physics behind the flow of low-frequency ac transport current around a closed superconducting circuit, where the circuit consists of two long, straight, parallel, uniform conductors, connected to each other at one end and to an applied emf at the other end. Thus one conductor is the return path for the other. A question of interest is what drives the current at any given point in the circuit. The answer given here is a surface charge, where the purpose of the surface charge is to spread the local emf around the circuit, so that at each point in the conductor it produces, together with the electric field of the vector potential, the electric field necessary for the current to flow. But it is then necessary to explain how the surface charge gets there, which is the central problem of the present analysis. The conclusion is that the total current density consists of the superposition of a large transport current and a very much smaller current system of a different symmetry. The transport current density is defined as a two-dimensional current density with no divergence. It flows uniformly along the conductor length, but can vary over the cross-section. The small additional current density has a much different symmetry, being three-dimensional and diverging at the surface of the conductor. Based on a slightly modified Bean model the transport current is treated as supercurrent having the value {+-}J {sub c}, while the small additional system of current is like normal current, with a density given by the electric field divided by a resistivity. The electric field is computed from the sum of the negative time derivative of the vector potential and the negative gradient of the scalar potential due to the surface charge. It has components parallel and perpendicular to the long axis of the conductor. Thus the small normal current density has a perpendicular component which flows into or out of the surface thereby creating the surface charge

  16. Doubled critical current density in Bi-2212 round wires by reduction of the residual bubble density

    Science.gov (United States)

    Jiang, J.; Starch, W. L.; Hannion, M.; Kametani, F.; Trociewitz, U. P.; Hellstrom, E. E.; Larbalestier, D. C.

    2011-08-01

    We have recently shown that the gas present in the only ~ 70% dense filaments of as-drawn Bi-2212 wire agglomerates into large bubbles that fill the entire filament diameter during the melt phase of the heat treatment. Once formed, these bubbles never disappear, although they can be bridged by 2212 grains formed on cooling. In order to test the effect of these bubbles on the critical current Ic, we increased the density of the filaments after drawing using 2 GPa of cold isostatic pressure, finding that the bubble density and size were greatly reduced and that Ic could be at least doubled. We conclude that enhancement of the filament packing density is of great importance for making major Ic improvements in this very useful, round superconducting wire.

  17. Influence of current density on surface morphology and properties of pulse plated tin films from citrate electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Ashutosh; Bhattacharya, Sumit; Das, Siddhartha; Das, Karabi, E-mail: karabi@metal.iitkgp.ernet.in

    2014-01-30

    Bulk polycrystalline tin films have been processed by pulse electrodeposition technique from a simple solution containing triammonium citrate and stannous chloride. The cathodic investigations have been carried out by galvanostatic methods. As deposited samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). XRD analysis of the deposited films shows microcrystalline grains having β-Sn form. The surface morphology is very rough at lower current density, but becomes smooth at higher current density, and exhibits pyramid type morphology at all the current densities. The effect of current density on microhardness, melting behavior, and electrical resistivity are also reported here.

  18. Lower hybrid counter current drive for edge current density modification in DIII-D

    Energy Technology Data Exchange (ETDEWEB)

    Fenstermacher, M.E.; Nevins, W.M. [Lawrence Livermore National Lab., CA (US); Porkolab, M.; Bonoli, P.T. [Massachusetts Inst. of Technology, Cambridge, MA (US). Plasma Fusion Center; Harvey, R.W. [General Atomics, San Diego, CA (US)

    1993-07-01

    Each of the Advanced Tokamak operating modes in DIII-D is thought to have a distinctive current density profile. So far these modes have only been achieved transiently through experiments which ramp the plasma current and shape. Extension of these modes to steady state requires non-inductive current profile control, e.g. with lower hybrid current drive (LHCD). Calculations of LHCD have been done for DIII-D using the ACCOME and CQL3D codes, showing that counter driven current at the plasma edge can cancel some of the undesirable edge bootstrap current and potentially extend the VH-mode. Results are presented for scenarios using 2.45 GHz LH waves launched from both the midplane and off-axis ports. The sensitivity of the results to injected power, n{sub e} and T{sub e}, and launched wave spectrum is also shown.

  19. Tokamak equilibria with strong toroidal current density reversal

    Science.gov (United States)

    Ludwig, G. O.; Rodrigues, Paulo; Bizarro, João P. S.

    2013-05-01

    The equilibrium of large magnetic islands in the core of a tokamak under conditions of strong toroidal current density reversal is investigated by a new method. The method uses distinct spectral representations to describe each simply connected region as well as the containing shell geometry. This ideal conducting shell may substitute for the plasma edge region or take a virtual character representing the external equilibrium field effect. The internal equilibrium of the islands is solved within the framework of the variational moment method. Equivalent surface current densities are defined on the boundaries of the islands and on the thin containing shell, giving a straightforward formulation to the interaction between regions. The equilibrium of the island-shell system is determined by matching moments of the Dirichlet boundary conditions. Finally, the macroscopic stability against a class of tilting displacements is examined by means of an energy principle. It is found out that the up-down symmetric islands are stable to this particular perturbation and geometry but the asymmetric system presents a bifurcation in the equilibrium.

  20. Magnetization of a Current-Carrying Superconducting Disk with B-Dependent Critical Current Density

    Science.gov (United States)

    Sohrabi, Mahdi; Babaei-Brojeny, Ali A.

    2010-11-01

    In the frame work of the critical state model (CSM), the magnetic response of a thin type-II superconducting disk that carries a radial transport current and is subjected to an applied magnetic field have been studied. To this end, we have studied the process of the magnetic flux-penetration. For a disk initially containing no magnetic flux but carrying a radial current, when a perpendicular magnetic field is applied, magnetic flux-penetration occurs in three stages: (1) the magnetic flux gradually penetrates from the edges of the disk until an instability occurs, (2) there is a rapid inflow of magnetic flux into the disk’s central region, which becomes resistive, and (3) magnetic flux continues to enter the disk, while persistent azimuthal currents flow in an outer annular region where the net current density is equal to J c . Also the behavior of a current-carrying disk subjected to an AC magnetic field is calculated. The magnetic flux, the current profiles and the magnetization hysteresis loops are calculated for several commonly used J c ( B) dependences. Finally, the results of the applications of the local field-dependent of the critical current density J c ( B) are compared with those obtained from the Bean model.

  1. Hydraulic jumps within pyroclastic density currents and their sedimentary record

    Science.gov (United States)

    Douillet, G.; Mueller, S.; Kueppers, U.; Dingwell, D. B.

    2013-12-01

    This contribution presents a complete and comprehensive formulation of the hydraulic jump phenomenon and reviews sedimentary structures that may be associated with them. Beginning from the general fluid phenomenon, we then focus on examples from pyroclastic density currents in order to infer dynamic parameters on the parent flows. A hydraulic jump is a fluid dynamics phenomenon that corresponds to the sudden increase of the thickness of a flow accompanied by a decrease of its velocity and/or density. A hydraulic jump is the expression of the transition of the flow from two different flow regimes: supercritical to subcritical. This entrains a change in the energy balance between kinetic energy and gravity potential energy. Recently, the terms of 'pneumatic jumps' have been used for similar phenomenon driven within a gas phase, and granular jumps for dense granular flows. It is thought that such strong changes in the flow conditions may leave characteristic structures in the sedimentary record. Indeed, the main variables influencing the sedimentation rate are the flow velocity, particle concentration and turbulence level, all of them strongly affected by a hydraulic jump. Structures deposited by hydraulic/pneumatic jumps have been called cyclic steps and chute and pool structures. Chute and pools represent the record of a single supercritical to subcritical transition, whereas cyclic steps are produced by stable trains of hydraulic jumps and subsequent re-accelerations. Pyroclastic density currents (PDCs) are gas and pyroclasts flows. As such, they can be subjected to granular and pneumatic jumps and their deposit have often been interpreted as containing records of jumps. Steep sided truncations covered by lensoidal layers have been interpreted as the record of internal jumps within density stratified flows. Fines-depleted breccias at breaks in slope are thought to result from the enhanced turbulence at a jump of the entire flow. Sudden increases in thickness of

  2. High Field Emission Current Density from Patterned Carbon Nanotube Field Emitter Arrays with Random Growth.

    Science.gov (United States)

    Khaneja, Mamta; Ghosh, Santanu; Gautam, Seema; Kumar, Prashant; Rawat, J S; Chaudhury, P K; Vankar, V D; Kumar, Vikram

    2015-05-01

    High field emission (FE) current density from carbon nanotube (CNT) arrays grown on lithographically patterned silicon substrates is reported. A typical patterned field emitter array consists of bundles of nanotubes separated by a fixed gap and spread over the entire emission area. Emission performance from such an array having randomly oriented nanotube growth within each bundle is reported for different bundle sizes and separations. One typical sample with aligned CNTs within the bundle is also examined for comparison. It is seen that the current density from an array having random nanotube growth within the bundles is appreciably higher as compared to its aligned counterpart. The influence of structure on FE current densities as revealed by Raman spectroscopy is also seen. It is also observed that current density depends on edge length and increases with the same for all samples under study. Highest current density of -100 mA cm(-2) at an applied field of 5 V/μm is achieved from the random growth patterned sample with a bundle size of 2 μm and spacing of 4 μm between the bundles.

  3. Cardiac activation mapping using ultrasound current source density imaging (UCSDI).

    Science.gov (United States)

    Olafsson, Ragnar; Witte, Russell S; Jia, Congxian; Huang, Sheng-Wen; Kim, Kang; O'Donnell, Matthew

    2009-03-01

    We describe the first mapping of biological current in a live heart using ultrasound current source density imaging (UCSDI). Ablation procedures that treat severe heart arrhythmias require detailed maps of the cardiac activation wave. The conventional procedure is time-consuming and limited by its poor spatial resolution (5-10 mm). UCSDI can potentially improve on existing mapping procedures. It is based on a pressure-induced change in resistivity known as the acousto-electric (AE) effect, which is spatially confined to the ultrasound focus. Data from 2 experiments are presented. A 540 kHz ultrasonic transducer (f/# = 1, focal length = 90 mm, pulse repetition frequency = 1600 Hz) was scanned over an isolated rabbit heart perfused with an excitation-contraction decoupler to reduce motion significantly while retaining electric function. Tungsten electrodes inserted in the left ventricle recorded simultaneously the AE signal and the low-frequency electrocardiogram (ECG). UCSDI displayed spatial and temporal patterns consistent with the spreading activation wave. The propagation velocity estimated from UCSDI was 0.25 +/- 0.05 mm/ms, comparable to the values obtained with the ECG signals. The maximum AE signal-to-noise ratio after filtering was 18 dB, with an equivalent detection threshold of 0.1 mA/ cm(2). This study demonstrates that UCSDI is a potentially powerful technique for mapping current flow and biopotentials in the heart.

  4. Critical state model with anisotropic critical current density

    CERN Document Server

    Bhagwat, K V; Ravikumar, G

    2003-01-01

    Analytical solutions of Bean's critical state model with critical current density J sub c being anisotropic are obtained for superconducting cylindrical samples of arbitrary cross section in a parallel geometry. We present a method for calculating the flux fronts and magnetization curves. Results are presented for cylinders with elliptical cross section with a specific form of the anisotropy. We find that over a certain range of the anisotropy parameter the flux fronts have shapes similar to those for an isotropic sample. However, in general, the presence of anisotropy significantly modifies the shape of the flux fronts. The field for full flux penetration also depends on the anisotropy parameter. The method is extended to the case of anisotropic J sub c that also depends on the local field B, and magnetization hysteresis curves are presented for typical values of the anisotropy parameter for the case of |J sub c | that decreases exponentially with |B|.

  5. Development of high temperature superconductors having high critical current density

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Gye Wong; Kim, C. J.; Lee, H.G.; Kwon, S. C.; Lee, H. J.; Kim, K. B.; Park, J. Y.; Jung, C. H

    2000-08-01

    Fabrication of high T{sub c} superconductors and its applications for electric power device were carried out for developing superconductor application technologies. High quality YBCO superconductors was fabricated by melt texture growth, top-seeded melt growth process and multi-seeded melt growth process and the properties was compared. The critical current density of the melt processed YBCO superconductors was about few 10,000 A/cm{sup 2} and the levitation force was 50 N. The processing time needed for the growth of the 123 single grain was greatly reduced by applying multi-seeding without no significant degradation of the levitation force. The multi-seeded melt growth process was confirmed as a time-saving and cost-effective method for the fabrication of bulk superconductors with controlled crystallographic orientation.

  6. Critical current densities in Bi-2223 sinter forgings.

    Energy Technology Data Exchange (ETDEWEB)

    Balachandran, U.; Fisher, B. L.; Goretta, K. C.; Harris, N. C.; Murayama, N.

    1999-07-23

    (Bi,Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} (Bi-2223) bars, prepared by sinter forging, exhibited good phase purity and strong textures with the c axes of the Bi-2223 grains parallel to the forging direction. The initial zero-field critical current density (J{sub c}) of the bars was 10{sup 3} A/cm{sup 2}, but because the forged bars were uncoated, this value decreased with repeated thermal cycling. J{sub c} as a function of applied magnetic field magnitude and direction roughly followed the dependencies exhibited by Ag-sheathed Bi-2223 tapes, but the forged bars were more strongly dependent on field strength and less strongly dependent on field angle.

  7. Ultra-high current density thin-film Si diode

    Science.gov (United States)

    Wang, Qi

    2008-04-22

    A combination of a thin-film .mu.c-Si and a-Si:H containing diode structure characterized by an ultra-high current density that exceeds 1000 A/cm.sup.2, comprising: a substrate; a bottom metal layer disposed on the substrate; an n-layer of .mu.c-Si deposited the bottom metal layer; an i-layer of .mu.c-Si deposited on the n-layer; a buffer layer of a-Si:H deposited on the i-layer, a p-layer of .mu.c-Si deposited on the buffer layer; and a top metal layer deposited on the p-layer.

  8. Identifying Distinguishing Characteristics of Secondary Pyroclastic Density Currents

    Science.gov (United States)

    Isom, S. L.; Brand, B. D.

    2014-12-01

    Pyroclastic density currents (PDCs) are ground-hugging mixtures of volcanic particles and gas that travel down the slopes of erupting volcanoes. The combination of high velocities, high bulk densities (due to particles in the current) and high temperatures make PDCs the most dangerous and deadly hazard associated with explosive volcanism. Secondary explosive phenomenon associated with PDCs, such as inland-directed surges (e.g., Montserrat, 2003) and phreatic explosions (e.g., Mt St Helens 1980) can increase the area affected and duration of the hazard. However, little work has been done on distinguishing the deposits of secondary explosive phenomenon from primary phenomenon. Samples have been acquired from the 1980 Mt St Helens phreatic explosion crater deposits and the 2003 eruptive event at Montserrat where a PDC flowed into the ocean, causing an inland-directed surge (Edmonds and Herd, 2005. Geology 33.4:245-248). The samples will be analyzed via depositional characteristics, granulometry, componentry, microscopic analysis and scanning electron microscope imaging. We hypothesize that thermal cracking or vesicle distortion (e.g., compression or hindered expansion) may occur in hot pyroclasts that enter a body of water, leading to a difference between the ash textures of primary PDCs, phreatic surges and inland-directed surge deposits. Analyzing granulometry and componentry from parent flows and secondary flows may also reveal distinguishing characteristics that will allow us to constrain differences in segregation mechanisms of particles for each phenomenon. Determining distinguishing depositional characteristics of these secondary phenomena is important for assessing their occurrence during past eruptions and identifying conditions conducive to the formation of secondary explosions. This will result in the ability to make more accurate hazard maps for volcanoes prone to explosive activity.

  9. High current density contacts for photoconductive semiconductor switches

    Energy Technology Data Exchange (ETDEWEB)

    Baca, A.G.; Hjalmarson, H.P.; Loubriel, G.M.; McLaughlin, D.L.; Zutavern, F.J.

    1993-08-01

    The current densities implied by current filaments in GaAs photoconductive semiconductor switches (PCSS) are in excess of 1 MA/cm{sup 2}. As the lateral switches are tested repeatedly, damage accumulates at the contacts until electrical breakdown occurs across the surface of the insulating region. In order to improve the switch lifetime, the incorporation of n- and p-type ohmic contacts in lateral switches as well as surface geometry modifications have been investigated. By using p-type AuBe ohmic contacts at the anode and n-type AuGe ohmic contacts at the cathode, contact lifetime improvements of 5--10x were observed compared to switches with n-type contacts at both anode and cathode. Failure analysis on samples operated for 1--1,000 shots show that extensive damage still exists for at least one contact on all switches observed and that temperatures approaching 500{degrees}C are can be reached. However, the n-type AuGe cathode is often found to have no damage observable by scanning electron microscopy (SEM). The observed patterns of contact degradation indicate directions for future contact improvements in lateral switches.

  10. Orbital functionals in density-matrix- and current-density-functional theory

    Energy Technology Data Exchange (ETDEWEB)

    Helbig, N.

    2006-05-15

    Density-Functional Theory (DFT), although widely used and very successful in the calculation of several observables, fails to correctly describe strongly correlated materials. In the first part of this work we, therefore, introduce reduced-densitymatrix- functional theory (RDMFT) which is one possible way to treat electron correlation beyond DFT. Within this theory the one-body reduced density matrix (1- RDM) is used as the basic variable. Our main interest is the calculation of the fundamental gap which proves very problematic within DFT. In order to calculate the fundamental gap we generalize RDMFT to fractional particle numbers M by describing the system as an ensemble of an N and an N+1 particle system (with N{<=}M{<=}N+1). For each fixed particle number, M, the total energy is minimized with respect to the natural orbitals and their occupation numbers. This leads to the total energy as a function of M. The derivative of this function with respect to the particle number has a discontinuity at integer particle number which is identical to the gap. In addition, we investigate the necessary and sufficient conditions for the 1- RDM of a system with fractional particle number to be N-representable. Numerical results are presented for alkali atoms, small molecules, and periodic systems. Another problem within DFT is the description of non-relativistic many-electron systems in the presence of magnetic fields. It requires the paramagnetic current density and the spin magnetization to be used as basic variables besides the electron density. However, electron-gas-based functionals of current-spin-density-functional Theory (CSDFT) exhibit derivative discontinuities as a function of the magnetic field whenever a new Landau level is occupied, which makes them difficult to use in practice. Since the appearance of Landau levels is, intrinsically, an orbital effect it is appealing to use orbital-dependent functionals. We have developed a CSDFT version of the optimized

  11. Differential modulation of corticospinal excitability by different current densities of anodal transcranial direct current stimulation.

    Directory of Open Access Journals (Sweden)

    Andisheh Bastani

    Full Text Available BACKGROUND: Novel non-invasive brain stimulation techniques such as transcranial direct current stimulation (tDCS have been developed in recent years. TDCS-induced corticospinal excitability changes depend on two important factors current intensity and stimulation duration. Despite clinical success with existing tDCS parameters, optimal protocols are still not entirely set. OBJECTIVE/HYPOTHESIS: The current study aimed to investigate the effects of four different anodal tDCS (a-tDCS current densities on corticospinal excitability. METHODS: Four current intensities of 0.3, 0.7, 1.4 and 2 mA resulting in current densities (CDs of 0.013, 0.029, 0.058 and 0.083 mA/cm(2 were applied on twelve right-handed (mean age 34.5±10.32 yrs healthy individuals in different sessions at least 48 hours apart. a-tDCS was applied continuously for 10 minute, with constant active and reference electrode sizes of 24 and 35 cm(2 respectively. The corticospinal excitability of the extensor carpi radialis muscle (ECR was measured before and immediately after the intervention and at 10, 20 and 30 minutes thereafter. RESULTS: Post hoc comparisons showed significant differences in corticospinal excitability changes for CDs of 0.013 mA/cm(2 and 0.029 mA/cm(2 (P = 0.003. There were no significant differences between excitability changes for the 0.013 mA/cm(2 and 0.058 mA/cm(2 (P = 0.080 or 0.013 mA/cm(2 and 0.083 mA/cm(2 (P = 0.484 conditions. CONCLUSION: This study found that a-tDCS with a current density of 0.013 mA/cm(2 induces significantly larger corticospinal excitability changes than CDs of 0.029 mA/cm(2. The implication is that might help to avoid applying unwanted amount of current to the cortical areas.

  12. Correlation of Critical Current Density with Cu3+ Concentration and Density in YBa2Cu3O7-x

    Science.gov (United States)

    Dou, S. X.; Liu, H. K.; Zhou, J. P.; Bourdillon, A. J.; Savvides, N.; Apperley, M.; Gouch, A.; Sorrell, C. C.

    Superconducting YBa2Cu3O7 wires and tapes were fabricated by cold drawing, rolling and extrusion processes. It was found that the critical current density, after O2 equilibration, correlates both with density and Cu3+ concentration. Full density was achieved by using a special heat treatment, but the critical current density was low owing to the low Cu3+ concentration present in this heavily twinned material. The best critical current density results were obtained for material with density of 92-95% of the theoretical value. The low critical current density of the porous specimens is attributed not only to a poor connectivity between grains but also to a low Cu3+ concentration due to the instability of Cu3+ at crystallite surfaces which increase in area with specimen porosity.

  13. Comparison of current density profiles based on particle orbit-driven current in steady-state plasma on QUEST

    Energy Technology Data Exchange (ETDEWEB)

    Alam, Md Mahbub, E-mail: m.alam@triam.kyushu-u.ac.jp [IGSES, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Nakamura, Kazuo [RIAM, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Xia, Fan [CFS, SWIP, P.O. Box 432, 610041 Chengdu (China); Mitarai, Osamu [Tokai University, Kumamoto 862-8652 (Japan); Hasegawa, Makoto; Tokunaga, Kazutoshi; Araki, Kuniaki; Zushi, Hideki; Hanada, Kazuaki; Fujisawa, Akihide; Idei, Hiroshi; Nagashima, Yoshihiko; Kawasaki, Shoji; Nakashima, Hisatoshi; Higashijima, Aki; Nagata, Takahiro [RIAM, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan)

    2016-11-01

    Highlights: • Electron cyclotron resonance heating (ECRH) of QUEST. • Particle guiding center orbit calculation. • Orbit-driven current density profile. • Hollow current density. • Equilibrium condition for steady-state operation of QUEST. - Abstract: In the present RF-driven divertor plasma of QUEST, it has been observed that orbit-driven current flows in the open magnetic surfaces outside of the closed magnetic surfaces. To observe this phenomenon and the characteristics of the orbit-driven current, current density profiles have been calculated on two different equilibrium conditions. We calculated current density profiles from particle guiding center orbits both for the fundamental and the second harmonic resonances for the 8.2 GHz electron cyclotron current drive. From this calculation, hollow current density profiles have been obtained with significant characteristics on both conditions. Only positive current distribution has been observed in the open magnetic surfaces outside of the closed magnetic surfaces.

  14. Lower-Dark-Current, Higher-Blue-Response CMOS Imagers

    Science.gov (United States)

    Pain, Bedabrata; Cunningham, Thomas; Hancock, Bruce

    2008-01-01

    Several improved designs for complementary metal oxide/semiconductor (CMOS) integrated-circuit image detectors have been developed, primarily to reduce dark currents (leakage currents) and secondarily to increase responses to blue light and increase signal-handling capacities, relative to those of prior CMOS imagers. The main conclusion that can be drawn from a study of the causes of dark currents in prior CMOS imagers is that dark currents could be reduced by relocating p/n junctions away from Si/SiO2 interfaces. In addition to reflecting this conclusion, the improved designs include several other features to counteract dark-current mechanisms and enhance performance.

  15. High-density matter: current status and future challenges

    Science.gov (United States)

    Stone, J. R.

    2015-05-01

    There are many fascinating processes in the Universe which we observe in more and more in detail thanks to increasingly sophisticated technology. One of the most interesting phenomena is the life cycle of stars, their birth, evolution and death. If the stars are massive enough, they end their lives in the core-collapse supernova explosion, the one of the most violent events in the Universe. As the result, the densest objects in the Universe, neutron stars and/or black holes are created. Naturally, the physical basis of these events should be understood in line with observation. The current status of our knowledge of processes in the life of stars is far from adequate for their true understanding. We show that although many models have been constructed their detailed ability to describe observations is limited or non-existent. Furthermore the general failure of all models means that we cannot tell which are heading in the right direction. A possible way forward in modeling of high-density matter is outlined, exemplified by the quark-meson-coupling model (QMC). This model has a natural explanation for the saturation of nuclear forces and depends on very few adjustable parameters, strongly constrained by the underlying physics. Latest QMC results for compact objects and finite nuclei are presented.

  16. High-density matter: current status and future challenges

    Directory of Open Access Journals (Sweden)

    Stone J. R.

    2015-01-01

    Full Text Available There are many fascinating processes in the Universe which we observe in more and more in detail thanks to increasingly sophisticated technology. One of the most interesting phenomena is the life cycle of stars, their birth, evolution and death. If the stars are massive enough, they end their lives in the core-collapse supernova explosion, the one of the most violent events in the Universe. As the result, the densest objects in the Universe, neutron stars and/or black holes are created. Naturally, the physical basis of these events should be understood in line with observation. The current status of our knowledge of processes in the life of stars is far from adequate for their true understanding. We show that although many models have been constructed their detailed ability to describe observations is limited or non-existent. Furthermore the general failure of all models means that we cannot tell which are heading in the right direction. A possible way forward in modeling of high-density matter is outlined, exemplified by the quark-meson-coupling model (QMC. This model has a natural explanation for the saturation of nuclear forces and depends on very few adjustable parameters, strongly constrained by the underlying physics. Latest QMC results for compact objects and finite nuclei are presented.

  17. Vibration effect on magnetization and critical current density of superconductors

    Science.gov (United States)

    Golovchanskiy, Igor A.; Pan, Alexey V.; George, Jonathan; Wells, Frederick S.; Fedoseev, Sergey A.; Rozenfeld, Anatoly

    2016-07-01

    In this work the effect of vibrations on critical current density (J c ) of superconductors has been studied. The vibrations are shown to affect J c of all types of superconductors during their measurements, employing a vibrating sample magnetometer (VSM). Increasing vibration frequency (f) and/or amplitude (A) leads to progressive reduction of J c as a function of magnetic field (B a ). The effect of vibrations is substantially stronger in thin films. It leads to development of unexpected kinks on {J}c({B}a) curves. Analysis of magnetization loops and relaxation of magnetization in YBCO films revealed that the vibration effect can be treated as the effective reduction of pinning potential. The asymmetry of the vibration effect in ascending and descending B a is observed, indicating differences in free energy of the corresponding vortex structures. Thermal effects induced by vibrations with large f and A are shown to have rather insignificant influence, while the vibrational vortex dynamics exhibit a strong impact. The irreversibility field ({B}{{irr}}) is shown to be instrumentally defined, and its value depends on VSM settings. In addition, the practical importance of {B}{{irr}} for J c modeling is demonstrated.

  18. Investigation of heavy current discharges with high initial gas density

    Energy Technology Data Exchange (ETDEWEB)

    Budin, A.; Bogomaz, A.; Kolikov, V.; Kuprin, A.; Leontiev, V.; Rutberg, P.; Shirokov, N. [Institute of Problems of Electrophysics of Russian Academy of Sciences, Dvortsovayanab., 18, St. Petersburg, 191065 (Russia)

    1996-05-01

    Piezoelectric pressure transducers, with noise immunity and time resolution of 0,5 {mu}s were used to measure pulse pressures of 430 MPa along the axis of an electrical discharge channel. Initial concentration of He was 2,7{center_dot}10{sup 21}cm{sup {minus}3}, dI/dt=6{center_dot}10{sup 11}A/s, and I{sub max}=560kA. Shock waves with amplitudes exceeding the pressure along the axis, were detected by a pressure transducer on the wall of the discharge chamber. Typical shock velocities were 2{center_dot}4km/s. Average pressure measurements along the discharge axis at different radii were used to estimate the current density distribution along the canal radius. The presence of the shock waves, promoting the additional hydrogen heating in the discharge chamber, has been registered during the discharge in hydrogen for I{sub max}{approximately}1MA and an initial concentration of 10{sup 21}cm{sup {minus}3}. {copyright} {ital 1996 American Institute of Physics.}

  19. Realizing life-scalable experimental pyroclastic density currents

    Science.gov (United States)

    Cronin, S. J.; Lube, G.; Breard, E.; Jones, J.; Valentine, G.; Freundt, A.; Hort, M. K.; Bursik, M. I.

    2013-12-01

    Pyroclastic Density Currents (PDCs) - the most deadly threat from volcanoes - are extremely hot, ground-hugging currents of rock fragments and gas that descend slopes at hundreds of kilometers per hour. These hostile flows are impossible to internally measure, thus volcanologists are persistently blocked in efforts to realistically forecast their internal mechanics and hazards. Attempts to fill this gap via laboratory-scale experiments continue to prove difficult, because they usually mismatch the dynamic and kinematic scaling of real-world flows by several orders of magnitude. In a multi-institutional effort, the first large-scale pyroclastic flow generator that can synthesize repeatable hot high-energy gas-particle mixture flows in safety has been commissioned in New Zealand. The final apparatus stands 15 m high, consisting of a tower/elevator system; an instrumented hopper that can hold >6000 kg (or 3.2 m3) of natural volcanic materials, which can be discharged at a range of controlled rates onto an instrumented, variably inclinable (6-25°) glass-sided chute for examining the vertical profiles of PDCs in motion. The use of rhyolitic pyroclastic material from the 1800 AD Taupo Eruption (with its natural grain-size, sorting and shape characteristics) and gas ensures natural coupling between the solids and fluid phases. PDC analogues with runout of >15 meters and flow depths of 1.5-6 meters are created by generating variably heated falling columns of natural volcanic particles (50-1300 kg/s), dispersed and aerated to controlled particle densities between 3 and 60 vol.% at the base of the elevated hopper. The descending columns rapidly generate high-velocity flows (up to 14 m/s) once impacting on the inclined channel, reproducing many features of natural flows, including segregation into dense and dilute regimes, progressive aggradational and en masse deposition of particles and the development of high internal gas-pore-pressures during flow. The PDC starting

  20. Effect of electrodeposition current density on the microstructure and magnetic properties of nickel-cobalt-molybdenum alloy powders

    Directory of Open Access Journals (Sweden)

    Pešić O.

    2014-01-01

    Full Text Available Nanostructured nickel-cobalt-molybdenum alloy powders were electrodeposited from an ammonium sulfate bath. The powders mostly consist of an amorphous phase and a very small amount of nanocrystals with an mean size of less than 3 nm. An increase in deposition current density increases the amorphous phase percentage, the density of chaotically distributed dislocations and internal microstrains in the powders, while decreasing the mean nanocrystal size. The temperature range over which the structural relaxation of the powders deposited at higher current densities occurs is shifted towards lower temperatures. A change in relative magnetic permeability during structural relaxation is higher in powders deposited at higher current densities. Powder crystallization takes place at temperatures above 700ºC. The formation of the stable crystal structure causes a decrease in relative magnetic permeability. [Projekat Ministarstva nauke Republike Srbije, br. 172057

  1. Current distribution and enhancement of the engineering critical current density in multifilament Bi-2223 tapes

    DEFF Research Database (Denmark)

    Wang, W.G.; Jensen, M.B.; Kindl, B.;

    2000-01-01

    The spatial distribution of the critical current density (Jc) and engineering critical current density (Je) along the tape width direction was studied by a cutting technique on Bi-2223 multifilamentary tapes. In general, an increase of Jc towards the centre of the tape was measured. We attribute...... this tendency to the stress-strain experienced in the tape during the rolling process. Jc of 50 kA/cm2 and Jeof 18 kA/cm2 was measured at the centre part (185 μm wide and 200 μm thick) of a tape cut from a 500 meters long tape (average Je of 8 kA/cm2). The low Jc of the edge part is a result of the porous...... microstructure with a great amount of secondary phases. Local variation of Jc was measured within the centre segment of the tape. This indicates the influence of other factors on Jc, such as filament shape, connectivity of the filaments, and sausaging. Enhancement of Je has been pursued in which average Je of 12...

  2. Crystallization of Ti33Cu67 metallic glass under high-current density electrical pulses

    Directory of Open Access Journals (Sweden)

    Mali Vyacheslav

    2011-01-01

    Full Text Available Abstract We have studied the phase and structure evolution of the Ti33Cu67 amorphous alloy subjected to electrical pulses of high current density. By varying the pulse parameters, different stages of crystallization could be observed in the samples. Partial polymorphic nanocrystallization resulting in the formation of 5- to 8-nm crystallites of the TiCu2 intermetallic in the residual amorphous matrix occurred when the maximum current density reached 9.7·108 A m-2 and the pulse duration was 140 μs, though the calculated temperature increase due to Joule heating was not enough to reach the crystallization temperature of the alloy. Samples subjected to higher current densities and higher values of the evolved Joule heat per unit mass fully crystallized and contained the Ti2Cu3 and TiCu3 phases. A common feature of the crystallized ribbons was their non-uniform microstructure with regions that experienced local melting and rapid solidification. PACS: 81; 81.05.Bx; 81.05.Kf.

  3. OLEDs under high current densities. Transient electroluminescence turn-on peaks and singlet-triplet quenching

    Energy Technology Data Exchange (ETDEWEB)

    Kasemann, Daniel

    2012-02-27

    densities. The triplet emitter system exhibits a slow rise of the EL after turn-on which prevents the usage of shorter pulses to enable higher current densities. The singlet emitter system, in contrast, exhibits a fast turn-on and reaches the maximum emission intensity within less than 20 ns. By several additional experiments including streak camera measurements and pump-probe experiments, the strong EL overshoot observed in the first few ns is successfully attributed to a reduced emission intensity in the steady state due to singlet-triplet annihilation. Hence, the separation of singlet emission and singlet-triplet quenching in time domain is demonstrated. At 550 A/cm{sup 2} and 10 ns pulse rise time, a peak luminance of 1.5.10{sup 6} cd/m{sup 2} is recorded. Finally, the experimental results are validated by modeling the singlet and triplet population dynamics in the emission layer of the fluorescent system to explain the time-resolved emission characteristics. Using a set of rate equations for the polaron density and the singlet and triplet exciton densities, the overshoot in singlet exciton density at the device turn-on is attributed to the separation of singlet emission and triplet quenching in time domain. Furthermore, by fitting the experimental data, the triplet-triplet annihilation rate in the host guest system is shown to become exciton density dependent at sufficiently high excitation density.

  4. Clast comminution during pyroclastic density current transport: Mt St Helens

    Science.gov (United States)

    Dawson, B.; Brand, B. D.; Dufek, J.

    2011-12-01

    Volcanic clasts within pyroclastic density currents (PDCs) tend to be more rounded than those in fall deposits. This rounding reflects degrees of comminution during transport, which produces an increase in fine-grained ash with distance from source (Manga, M., Patel, A., Dufek., J. 2011. Bull Volcanol 73: 321-333). The amount of ash produced due to comminution can potentially affect runout distance, deposit sorting, the volume of ash lofted into the upper atmosphere, and increase internal pore pressure (e.g., Wohletz, K., Sheridan, M. F., Brown, W.K. 1989. J Geophy Res, 94, 15703-15721). For example, increased pore pressure has been shown to produce longer runout distances than non-comminuted PDC flows (e.g., Dufek, J., and M. Manga, 2008. J. Geophy Res, 113). We build on the work of Manga et al., (2011) by completing a pumice abrasion study for two well-exposed flow units from the May 18th, 1980 eruption of Mt St Helens (MSH). To quantify differences in comminution from source, sampling and the image analysis technique developed in Manga et al., 2010 was completed at distances proximal, medial, and distal from source. Within the units observed, data was taken from the base, middle, and pumice lobes within the outcrops. Our study is unique in that in addition to quantifying the degree of pumice rounding with distance from source, we also determine the possible range of ash sizes produced during comminution by analyzing bubble wall thickness of the pumice through petrographic and SEM analysis. The proportion of this ash size is then measured relative to the grain size of larger ash with distance from source. This allows us to correlate ash production with degree of rounding with distance from source, and determine the fraction of the fine ash produced due to comminution versus vent-fragmentation mechanisms. In addition we test the error in 2D analysis by completing a 3D image analysis of selected pumice samples using a Camsizer. We find that the roundness of PDC

  5. Affirmative Action in Higher Education: A Current Legal Overview.

    Science.gov (United States)

    Alger, Jonathan

    Legal challenges to affirmative action continue in a variety of contexts within higher education, creating confusion and uncertainty for colleges and universities. This paper examines cases brought in federal court, although other complaints related to affirmative action programs have been filed in state courts and with the U.S. Department of…

  6. Current State and Problems of Higher Education Reform

    Science.gov (United States)

    Salnikov, N.; Burukhin, S.

    2009-01-01

    Higher education in Russia is experiencing changes in curriculum and in the specialization and function of institutions in the search for a better model for a post-Soviet society. The early 1990s saw the start of the reform of the system of education in Russia. However, problems of quality and of continuity with secondary education have still not…

  7. Current Challenges in Higher Education Administration and Management

    Science.gov (United States)

    Baldwin, Jon F.

    2009-01-01

    UK higher education has a proud tradition stretching back centuries, with St. Andrews almost 600 years old, and teaching having existed at Oxford for more than 900 years. There is no reason why universities established more recently should not demonstrate similar longevity. The management of stakeholders has always been central to the successful…

  8. Current Challenges in Higher Education Administration and Management

    Science.gov (United States)

    Baldwin, Jon F.

    2009-01-01

    UK higher education has a proud tradition stretching back centuries, with St. Andrews almost 600 years old, and teaching having existed at Oxford for more than 900 years. There is no reason why universities established more recently should not demonstrate similar longevity. The management of stakeholders has always been central to the successful…

  9. The Evaluation of Music Faculty in Higher Education: Current Practices

    Science.gov (United States)

    Parkes, Kelly A.

    2015-01-01

    The purpose of this research was to ascertain the methods used to evaluate music faculty and whether achievement measures, or student progress, impact the evaluations made about teacher effectiveness for music faculty in the higher education context. The author surveyed Chairs of Departments or Directors of Schools of Music (n = 412) listed as…

  10. Enhanced current and power density of micro-scale microbial fuel cells with ultramicroelectrode anodes

    Science.gov (United States)

    Ren, Hao; Rangaswami, Sriram; Lee, Hyung-Sool; Chae, Junseok

    2016-09-01

    We present a micro-scale microbial fuel cell (MFC) with an ultramicroelectrode (UME) anode, with the aim of creating a miniaturized high-current/power-density converter using carbon-neutral and renewable energy sources. Micro-scale MFCs have been studied for more than a decade, yet their current and power densities are still an order of magnitude lower than those of their macro-scale counterparts. In order to enhance the current/power densities, we engineer a concentric ring-shaped UME, with a width of 20 μm, to facilitate the diffusion of ions in the vicinity of the micro-organisms that form biofilm on the UME. The biofilm extends approximately 15 μm from the edge of the UME, suggesting the effective biofilm area increases. Measured current/power densities per the effective area and the original anode area are 7.08  ±  0.01 A m-2 & 3.09  ±  0.04 W m-2 and 17.7  ±  0.03 A m-2 & 7.72  ±  0.09 W m-2, respectively. This is substantially higher than any prior work in micro-scale MFCs, and very close, or even higher, to that of macro-scale MFCs. A Coulombic efficiency, a measure of how efficiently an MFC harvests electrons from donor substrate, of 70%, and an energy conversion efficiency of 17% are marked, highlighting the micro-scale MFC as an attractive alternative within the existing energy conversion portfolio.

  11. Use of catalytic anodes for zinc electrowinning at high current densities from purified electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Bestetti, M.; Ducati, U. [Polytechnic of Milan, Dept. of Applied Physical Chemistry, Milan (Italy); Kelsall, G.H. [T.H. Huxley School, Imperial College, London (United Kingdom); Li, G. [Cominco Research, Cominco Limited, Trail, British Columbia (Canada); Guerra, E. [Univ. of British Columbia, Dept. of Metals and Materials Engineering, Victoria, British Columbia (Canada)

    2001-07-01

    Substantial energy savings are possible in zinc electrowinning by substituting catalytic oxygen evolution anodes for conventional lead-silver anodes. However, it is well known that the harmful effects of impurities usually present in zinc electrolyte solutions limit the service life of catalytic anodes, though their purification by solvent extraction could obviate such problems. Laboratory-scale zinc deposition experiments, with synthetic electrolytes have been performed to determine the effects of current density, temperature, and electrolyte composition on cell voltages and current efficiencies. These data sets were used in an assessment of the optimum design parameters of the tank house. Zinc electrowinning at high current densities (higher than 2000 A/m{sup 2}) using catalytic anodes and purified solutions (e.g., by solvent extraction), is proposed as an alternative to the conventional process, which is based on lead-silver anodes working at relatively low current densities (ca. 500 A/m{sup 2}). Finally, a system for continuous deposition and stripping of the metal is discussed. (author)

  12. Low-energy-density diets are associated with higher diet quality and higher diet costs in French adults.

    Science.gov (United States)

    Drewnowski, Adam; Monsivais, Pablo; Maillot, Matthieu; Darmon, Nicole

    2007-06-01

    Low-energy-density diets are often recommended for weight control. Such diets have a higher nutrient content than do high-energy-density diets. This study tested the hypothesis that energy-dense diets have a relatively low monetary cost, whereas less energy-dense diets are more expensive. In this cross-sectional study, dietary intakes of 1,474 French adults (672 men, 802 women), aged 15 to 92 years, were assessed using 7-day diet records. Dietary energy density (kcal/g) was calculated by dividing total dietary energy by the edible weight of foods and caloric beverages consumed. Diet cost ($/7 days or $/2,000 kcal) was estimated using mean national food prices for 895 foods. The relationship between dietary energy density and diet cost was examined in a linear regression model. Within each quintile of energy intakes, the more energy-dense diets were associated with lower diet quality and with lower diet costs (r(2)=0.38 to 0.44). In a regression model, the more energy-dense diets cost less, whereas low-energy-density diets cost substantially more, adjusting for energy intakes, sex, and age. The finding that energy-dense diets cost less per 2,000 kcal may help explain why the highest rates of obesity are observed among groups of limited economic means. The finding that low-energy-density diets are associated with higher diet costs suggests that lasting improvements in diet quality may require economic as well as behavioral interventions.

  13. An Assessment of Reservoir Density Currents and Inflow Processes

    Science.gov (United States)

    1983-07-01

    are defined once where used in the main text and appendices and, for convience , are listed and redefined in Appendix D. Unless specifically stated...techniques are described hereafter and sample applications are presented in Appendix B. Overflows 118. Overflows occur when the inflowing water density is

  14. Fourier transform magnetic resonance current density imaging (FT-MRCDI) from one component of magnetic flux density.

    Science.gov (United States)

    Ider, Yusuf Ziya; Birgul, Ozlem; Oran, Omer Faruk; Arikan, Orhan; Hamamura, Mark J; Muftuler, L Tugan

    2010-06-01

    Fourier transform (FT)-based algorithms for magnetic resonance current density imaging (MRCDI) from one component of magnetic flux density have been developed for 2D and 3D problems. For 2D problems, where current is confined to the xy-plane and z-component of the magnetic flux density is measured also on the xy-plane inside the object, an iterative FT-MRCDI algorithm is developed by which both the current distribution inside the object and the z-component of the magnetic flux density on the xy-plane outside the object are reconstructed. The method is applied to simulated as well as actual data from phantoms. The effect of measurement error on the spatial resolution of the current density reconstruction is also investigated. For 3D objects an iterative FT-based algorithm is developed whereby the projected current is reconstructed on any slice using as data the Laplacian of the z-component of magnetic flux density measured for that slice. In an injected current MRCDI scenario, the current is not divergence free on the boundary of the object. The method developed in this study also handles this situation.

  15. Reconstruction of conductivity and current density images using only one component of magnetic field measurements.

    Science.gov (United States)

    Seo, Jin Keun; Yoon, Jeong-Rock; Woo, Eung Je; Kwon, Ohin

    2003-09-01

    Magnetic resonance current density imaging (MRCDI) is to provide current density images of a subject using a magnetic resonance imaging (MRI) scanner with a current injection apparatus. The injection current generates a magnetic field that we can measure from MR phase images. We obtain internal current density images from the measured magnetic flux densities via Ampere's law. However, we must rotate the subject to acquire all of the three components of the induced magnetic flux density. This subject rotation is impractical in clinical MRI scanners when the subject is a human body. In this paper, we propose a way to eliminate the requirement of subject rotation by careful mathematical analysis of the MRCDI problem. In our new MRCDI technique, we need to measure only one component of the induced magnetic flux density and reconstruct both cross-sectional conductivity and current density images without any subject rotation.

  16. Comparison of exact-exchange calculations for solids in current-spin-density- and spin-density-functional theory

    DEFF Research Database (Denmark)

    Sharma, S.; Pittalis, S.; Kurth, S.;

    2007-01-01

    The relative merits of current-spin-density- and spin-density-functional theory are investigated for solids treated within the exact-exchange-only approximation. Spin-orbit splittings and orbital magnetic moments are determined at zero external magnetic field. We find that for magnetic (Fe, Co...

  17. Remediation of print: On the current restructuration of higher education

    Directory of Open Access Journals (Sweden)

    Helge Høivik

    2014-09-01

    Full Text Available The educational establishment was built and structured on a communication pattern at the core of the Gutenberg Galaxy that combines the spoken word with printed and handwritten resources. The current digitization of text is a pacesetter for retooling the workplace in the "industries of signs", for replacing skills on a broad scale and for developing new formal and informal social relationships. In addition to technological developments, a strong driver of this process is the cost of the mainly manual modes of academic operation. Core inhibitors to change are century-old traditions embedded in brick-and-mortar institutions, the impossibility of enforcing industrial-type organization on knowledge work and an elitist and scholastic bent in the academic concept of self. The field is thus in need of a new Grammar of Schooling that reflects technologically and socially driven participation modes that better address educational needs and cost considerations. The educational institution is challenged to develop a new logic of production in its educational mission.

  18. Incorporating current research into formal higher education settings using Astrobites

    Science.gov (United States)

    Sanders, Nathan E.; Kohler, Susanna; Faesi, Chris; Villar, Ashley; Zevin, Michael

    2017-10-01

    A primary goal of many undergraduate- and graduate-level courses in the physical sciences is to prepare students to engage in scientific research or to prepare students for careers that leverage skillsets similar to those used by research scientists. Even for students who may not intend to pursue a career with these characteristics, exposure to the context of applications in modern research can be a valuable tool for teaching and learning. However, a persistent barrier to student participation in research is familiarity with the technical language, format, and context that academic researchers use to communicate research methods and findings with each other: the literature of the field. Astrobites, an online web resource authored by graduate students, has published brief and accessible summaries of more than 1300 articles from the astrophysical literature since its founding in 2010. This article presents three methods for introducing students at all levels within the formal higher education setting to approaches and results from modern research. For each method, we provide a sample lesson plan that integrates content and principles from Astrobites, including step-by-step instructions for instructors, suggestions for adapting the lesson to different class levels across the undergraduate and graduate spectrum, sample student handouts, and a grading rubric.

  19. Theoretical Modeling of Internal Hydraulic Jump in Density Currents

    CERN Document Server

    Firoozabadi, Bahar; Aryanfar, Asghar; Afshin, Hossein

    2013-01-01

    In this paper, we propose an analytical framework for internal hydraulic jumps. Density jumps or internal hydraulic jumps occur when a supper critical flow of water discharges into a stagnant layer of water with slightly different density. The approach used here is control volume method which is also used to analyze ordinary hydraulic jumps. The important difference here is that entrainment is taken into account. Using conservation equations with the aid of some simplifying assumptions we come to an equation that gives jump downstream height as function of jump upstream characteristics and the entrainment. To determine the magnitude of downstream height we use an experimental equation for calculating the entrainment. Finally we verify our framework by comparing the height that we gain from the derived equation with some experimental data.

  20. Lower hybrid current drive for edge current density modification in DIII-D: Final status report

    Energy Technology Data Exchange (ETDEWEB)

    Fenstermacher, M.E. [Lawrence Livermore National Lab., CA (United States); Porkolab, M. [Massachusetts Inst. of Tech., Cambridge, MA (United States). Plasma Fusion Center

    1993-08-04

    Application of Lower Hybrid (LH) Current Drive (CD) in the DIII-D tokamak has been studied at LLNL, off and on, for several years. The latest effort began in February 1992 in response to a letter from ASDEX indicating that the 2.45 GHz, 3 MW system there was available to be used on another device. An initial assessment of the possible uses for such a system on DIII-D was made and documented in September 1992. Multiple meetings with GA personnel and members of the LH community nationwide have occurred since that time. The work continued through the submission of the 1995 Field Work Proposals in March 1993 and was then put on hold due to budget limitations. The purpose of this document is to record the status of the work in such a way that it could fairly easily be restarted at a future date. This document will take the form of a collection of Appendices giving both background and the latest results from the FY 1993 work, connected by brief descriptive text. Section 2 will describe the final workshop on LHCD in DIII-D held at GA in February 1993. This was an open meeting with attendees from GA, LLNL, MIT and PPPL. Summary documents from the meeting and subsequent papers describing the results will be included in Appendices. Section 3 will describe the status of work on the use of low frequency (2.45 GHZ) LH power and Parametric Decay Instabilities (PDI) for the special case of high dielectric in the edge regions of the DIII-D plasma. This was one of the critical issues identified at the workshop. Other potential issues for LHCD in the DIII-D scenarios are: (1) damping of the waves on fast ions from neutral beam injection, (2) runaway electrons in the low density edge plasma, (3) the validity of the WKB approximation used in the ray-tracing models in the steep edge density gradients.

  1. A new wavelet transform to sparsely represent cortical current densities for EEG/MEG inverse problems.

    Science.gov (United States)

    Liao, Ke; Zhu, Min; Ding, Lei

    2013-08-01

    The present study investigated the use of transform sparseness of cortical current density on human brain surface to improve electroencephalography/magnetoencephalography (EEG/MEG) inverse solutions. Transform sparseness was assessed by evaluating compressibility of cortical current densities in transform domains. To do that, a structure compression method from computer graphics was first adopted to compress cortical surface structure, either regular or irregular, into hierarchical multi-resolution meshes. Then, a new face-based wavelet method based on generated multi-resolution meshes was proposed to compress current density functions defined on cortical surfaces. Twelve cortical surface models were built by three EEG/MEG softwares and their structural compressibility was evaluated and compared by the proposed method. Monte Carlo simulations were implemented to evaluate the performance of the proposed wavelet method in compressing various cortical current density distributions as compared to other two available vertex-based wavelet methods. The present results indicate that the face-based wavelet method can achieve higher transform sparseness than vertex-based wavelet methods. Furthermore, basis functions from the face-based wavelet method have lower coherence against typical EEG and MEG measurement systems than vertex-based wavelet methods. Both high transform sparseness and low coherent measurements suggest that the proposed face-based wavelet method can improve the performance of L1-norm regularized EEG/MEG inverse solutions, which was further demonstrated in simulations and experimental setups using MEG data. Thus, this new transform on complicated cortical structure is promising to significantly advance EEG/MEG inverse source imaging technologies.

  2. Analysis of recoverable current from one component of magnetic flux density in MREIT and MRCDI.

    Science.gov (United States)

    Park, Chunjae; Lee, Byung Il; Kwon, Oh In

    2007-06-01

    Magnetic resonance current density imaging (MRCDI) provides a current density image by measuring the induced magnetic flux density within the subject with a magnetic resonance imaging (MRI) scanner. Magnetic resonance electrical impedance tomography (MREIT) has been focused on extracting some useful information of the current density and conductivity distribution in the subject Omega using measured B(z), one component of the magnetic flux density B. In this paper, we analyze the map Tau from current density vector field J to one component of magnetic flux density B(z) without any assumption on the conductivity. The map Tau provides an orthogonal decomposition J = J(P) + J(N) of the current J where J(N) belongs to the null space of the map Tau. We explicitly describe the projected current density J(P) from measured B(z). Based on the decomposition, we prove that B(z) data due to one injection current guarantee a unique determination of the isotropic conductivity under assumptions that the current is two-dimensional and the conductivity value on the surface is known. For a two-dimensional dominating current case, the projected current density J(P) provides a good approximation of the true current J without accumulating noise effects. Numerical simulations show that J(P) from measured B(z) is quite similar to the target J. Biological tissue phantom experiments compare J(P) with the reconstructed J via the reconstructed isotropic conductivity using the harmonic B(z) algorithm.

  3. DISCONTINUOUS FLOW OF TURBID DENSITY CURRENTS I. CHANNEL EXPANSION AND CONTRACTION

    Institute of Scientific and Technical Information of China (English)

    Jiahua FAN

    2005-01-01

    Laboratory experiments on turbid density currents were conducted to observe the flow features of these currents with abrupt contracted and expanded reaches. Experimental data were used to determine water entrainment coefficients for both channel expansion and contraction. Expressions for turbid density currents with water entrainment coefficients in abrupt contracted and expanded reaches were derived,and compared with experimental data.

  4. Method for determining transport critical current densities and flux penetration depth in bulk superconductors

    Science.gov (United States)

    Israelsson, Ulf E. (Inventor); Strayer, Donald M. (Inventor)

    1992-01-01

    A contact-less method for determining transport critical current density and flux penetration depth in bulk superconductor material. A compressor having a hollow interior and a plunger for selectively reducing the free space area for distribution of the magnetic flux therein are formed of superconductor material. Analytical relationships, based upon the critical state model, Maxwell's equations and geometrical relationships define transport critical current density and flux penetration depth in terms of the initial trapped magnetic flux density and the ratio between initial and final magnetic flux densities whereby data may be reliably determined by means of the simple test apparatus for evaluating the current density and flux penetration depth.

  5. Dependence of the critical current density on the first matching field density

    Energy Technology Data Exchange (ETDEWEB)

    Obaidat, I.M. [Department of Physics, United Arab Emirates University, Al-Ain 17551 (United Arab Emirates)], E-mail: iobaidat@uaeu.ac.ae; Benkraouda, M.; Khawaja, U. Al [Department of Physics, United Arab Emirates University, Al-Ain 17551 (United Arab Emirates)

    2008-10-01

    Molecular dynamic simulations were carried out to investigate the properties of the critical depinning force in high temperature superconductors at several vortex densities at the first matching field. The study was conducted on samples with periodic square arrays of vortices and pinning sites. The variables in the simulations were the vortex density, the pinning sites density, the temperature, the pinning strength, the size of pinning sites. The critical depinning force is found to decrease with temperature for all first matching field densities. The rate of this decrease was found to be slower as the pinning strength and size of pinning site gets larger. At low temperatures and for large pinning strengths, the critical depinning force was found to decrease with increasing the first matching field density. But very interesting results were obtained at moderate temperatures where the critical depinning force was found to increase as the first matching field density increases. The same behavior of the critical depinning force was found at low temperatures, for small pinning strengths. These unexpected results were attributed to a vortex structural phase transition from a disordered state to an ordered state.

  6. Reaching Higher Densities for Laboratory White Dwarf Photospheres to Measure Spectroscopic Line Profiles

    CERN Document Server

    Falcon, Ross E; Gomez, T A; Schaeuble, M; Nagayama, T; Montgomery, M H; Winget, D E; Rochau, G A

    2016-01-01

    As part of our laboratory investigation of the theoretical line profiles used in white dwarf atmosphere models, we extend the electron-density ($n_{\\rm e}$) range measured by our experiments to higher densities (up to $n_{e}\\sim80\\times10^{16}$ cm$^{-3}$). Whereas inferred parameters using the hydrogen-$\\beta$ spectral line agree among different line-shape models for $n_{\\rm e}\\lesssim30\\times10^{16}$ cm$^{-3}$, we now see divergence between models. These are densities beyond the range previously benchmarked in the laboratory, meaning theoretical profiles in this regime have not been fully validated. Experimentally exploring these higher densities enables us to test and constrain different line-profile models, as the differences in their relative H-Balmer line shapes are more pronounced at such conditions. These experiments also aid in our study of occupation probabilities because we can measure these from relative line strengths.

  7. Influence of Jet Angle and Ion Density of Cathode Side on Low Current Vacuum Arc Characteristics

    Institute of Scientific and Technical Information of China (English)

    WANG Lijun; JIA Shenli; SHI Zongqian

    2008-01-01

    In this study, the influence of the initial jet angles (IJAs) and ion number densities (INDs) at the cathode side on the low current vacuum arc (LCVA) characteristics is simulated and analysed. The results show that the ion temperature, electron temperature, ion number density, axial current density and plasma pressure all decrease with the increase of the cathode IJAs. It is also shown that LCVA can cause a current constriction for lower cathode IND, and the anode sheath potential is more nonuniform, which is mainly related to the nonuniform distribution of the axial current density at the anode side.

  8. Engineering Critical Current Density Improvement in Ag- Bi-2223 Tapes

    DEFF Research Database (Denmark)

    Wang, W. G.; Seifi, Behrouz; Eriksen, Morten

    2000-01-01

    round wire as a preform prior to the flat rolling that achieved more homogenous filament distribution. Filament geometry and density were simulated by Finite Element Modeling. The tapes with large filling factor up to 45 % have been produced with a hard metal outer sheath, which facilitates...... the superconductor composite sustaining large proportional oxide ceramics in the composite during drawing and rolling process. By optimization of the thermal and mechanical process, a Je of 12 kA/cm2 has been achieved in a 0.183.1 mm2 size tape which carried 67 A...... factor of the tapes. Phase evolution at initial sintering stage has been studied by a quench experiment in Ag-Bi-2223 tapes. The content, texture, and microstructure of various phases were determined by XRD and SEM. A novel process approach has been invented in which square wire was chosen rather than...

  9. Quasi-ballistic carbon nanotube array transistors with current density exceeding Si and GaAs.

    Science.gov (United States)

    Brady, Gerald J; Way, Austin J; Safron, Nathaniel S; Evensen, Harold T; Gopalan, Padma; Arnold, Michael S

    2016-09-01

    Carbon nanotubes (CNTs) are tantalizing candidates for semiconductor electronics because of their exceptional charge transport properties and one-dimensional electrostatics. Ballistic transport approaching the quantum conductance limit of 2G 0 = 4e (2)/h has been achieved in field-effect transistors (FETs) containing one CNT. However, constraints in CNT sorting, processing, alignment, and contacts give rise to nonidealities when CNTs are implemented in densely packed parallel arrays such as those needed for technology, resulting in a conductance per CNT far from 2G 0. The consequence has been that, whereas CNTs are ultimately expected to yield FETs that are more conductive than conventional semiconductors, CNTs, instead, have underperformed channel materials, such as Si, by sixfold or more. We report quasi-ballistic CNT array FETs at a density of 47 CNTs μm(-1), fabricated through a combination of CNT purification, solution-based assembly, and CNT treatment. The conductance is as high as 0.46 G 0 per CNT. In parallel, the conductance of the arrays reaches 1.7 mS μm(-1), which is seven times higher than the previous state-of-the-art CNT array FETs made by other methods. The saturated on-state current density is as high as 900 μA μm(-1) and is similar to or exceeds that of Si FETs when compared at and equivalent gate oxide thickness and at the same off-state current density. The on-state current density exceeds that of GaAs FETs as well. This breakthrough in CNT array performance is a critical advance toward the exploitation of CNTs in logic, high-speed communications, and other semiconductor electronics technologies.

  10. Quasi-ballistic carbon nanotube array transistors with current density exceeding Si and GaAs

    Science.gov (United States)

    Brady, Gerald J.; Way, Austin J.; Safron, Nathaniel S.; Evensen, Harold T.; Gopalan, Padma; Arnold, Michael S.

    2016-01-01

    Carbon nanotubes (CNTs) are tantalizing candidates for semiconductor electronics because of their exceptional charge transport properties and one-dimensional electrostatics. Ballistic transport approaching the quantum conductance limit of 2G0 = 4e2/h has been achieved in field-effect transistors (FETs) containing one CNT. However, constraints in CNT sorting, processing, alignment, and contacts give rise to nonidealities when CNTs are implemented in densely packed parallel arrays such as those needed for technology, resulting in a conductance per CNT far from 2G0. The consequence has been that, whereas CNTs are ultimately expected to yield FETs that are more conductive than conventional semiconductors, CNTs, instead, have underperformed channel materials, such as Si, by sixfold or more. We report quasi-ballistic CNT array FETs at a density of 47 CNTs μm−1, fabricated through a combination of CNT purification, solution-based assembly, and CNT treatment. The conductance is as high as 0.46 G0 per CNT. In parallel, the conductance of the arrays reaches 1.7 mS μm−1, which is seven times higher than the previous state-of-the-art CNT array FETs made by other methods. The saturated on-state current density is as high as 900 μA μm−1 and is similar to or exceeds that of Si FETs when compared at and equivalent gate oxide thickness and at the same off-state current density. The on-state current density exceeds that of GaAs FETs as well. This breakthrough in CNT array performance is a critical advance toward the exploitation of CNTs in logic, high-speed communications, and other semiconductor electronics technologies. PMID:27617293

  11. Peltier effect in multilayered nanopillars under high density charge current

    Science.gov (United States)

    Gravier, L.; Fukushima, A.; Kubota, H.; Yamamoto, A.; Yuasa, S.

    2006-12-01

    From the basic equations of thermoelectricity, we model the thermal regimes that develop in multilayered nanopillar elements experiencing continuous charge currents. The energy conservation principle was applied to all layer-layer and layer-electrode junctions. The obtained set of equations was solved to derive the temperature of each junction. The contribution of the Peltier effect is included in an effective resistance. This model gives satisfactory fits to experimental data obtained on a series of reference nanopillar elements.

  12. Peltier effect in multilayered nanopillars under high density charge current

    Energy Technology Data Exchange (ETDEWEB)

    Gravier, L [Institut de Physique des Nanostructures, Ecole Polytechnique Federale de Lausanne (EPFL), EPFL-SB-IPN station 3, 1015 Lausanne (Switzerland); Fukushima, A [National Institute of Advances Industrial Science and Technology (AIST) 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan); Kubota, H [National Institute of Advances Industrial Science and Technology (AIST) 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan); Yamamoto, A [National Institute of Advances Industrial Science and Technology (AIST) 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan); Yuasa, S [National Institute of Advances Industrial Science and Technology (AIST) 1-1-1 Umezono, Tsukuba, Ibaraki 305-8568 (Japan)

    2006-12-21

    From the basic equations of thermoelectricity, we model the thermal regimes that develop in multilayered nanopillar elements experiencing continuous charge currents. The energy conservation principle was applied to all layer-layer and layer-electrode junctions. The obtained set of equations was solved to derive the temperature of each junction. The contribution of the Peltier effect is included in an effective resistance. This model gives satisfactory fits to experimental data obtained on a series of reference nanopillar elements.

  13. Equilibria and Stability of JET Discharges with Zero Core Current Density

    Energy Technology Data Exchange (ETDEWEB)

    B.C. Stratton; N.C. Hawkes; G.T.A. Huysmans; J.A. Breslau; L.E. Zakharov; B. Alper; R.V. Budny; C.D. Challis; R. Deangelis; V. Drozdov; C. Fenzi; C. Giroud; T.C. Hender; J. Hobirk; S.C. Jardin; E. Joffrin; P.J. Lomas; P. Lotte; J. Mailloux; W. Park; E. Rachlew; S. Reyes-Cortes; E. Solano; T. Tala; K-D. Zastrow; JET-EFDA Contributors

    2002-10-15

    Injection of Lower Hybrid Heating and Current Drive (LHCD) into the current ramp-up phase of JET [Joint European Torus] discharges can produce extremely reversed q-profiles characterized by a core region of near zero current density (within Motional Stark Effect diagnostic measurement errors). Non-inductive, off-axis co-current drive induces a back electromotive force inside the non-inductive current radius that drives a negative current in the plasma core. The core current density does not go negative, although current diffusion calculations indicate that there is sufficient LHCD to cause this. The clamping of the core current density near zero is consistent with n=0 reconnection events redistributing the core current soon after it goes negative. This is seen in reduced MHD simulations and in nonlinear resistive MHD simulations which predict that these discharges undergo n=0 reconnection events that clamp the core current near zero.

  14. Changes of IK,ATP current density and allosteric modulation during chronic atrial fibrillation

    Institute of Scientific and Technical Information of China (English)

    WU Gang; HUANG Cong-xin; TANG Yan-hong; JIANG Hong; WAN Jun; CHEN Hui; XIE Qiang; HUANG Zheng-rong

    2005-01-01

    Background Atrial fibrillation (AF) is the most common supraventricular arrhythmia in clinical practice. Chronic atrial fibrillation (CAF) is associated with ionic remodeling. However, little is known about the activity of ATP-sensitive potassium current (IK,ATP) during CAF. So we studied the changes of IK,ATP density and allosteric modulation of ATP-sensitivity by intracellular pH during CAF.Methods Myocardium samples were obtained from the right auricular appendage of patients with rheumatic heart disease complicated with valvular disease in sinus rhythm (SR) or CAF. There were 14 patients in SR group and 9 patients in CAF group. Single atrial cells were isolated using an enzyme dispersion technique. IK,ATP was recorded using the whole-cell and inside-out configuration of voltage-clamp techniques. In whole-cell model, myocytes of SR and CAF groups were perfused with simulated ischemic solution to elicit IK,ATP. In inside-out configuration, the internal patch membranes were exposed to different ATP concentrations in pH 7.4 and 6.8.Results Under simulated ischemia, IK,ATP current density of CAF group was significantly higher than in SR group [(83.5±10.8) vs. (58.7±8.4) pA/pF, P<0.01]. IK,ATP of the two groups showed ATP concentration-dependent inhibition. The ATP concentration for 50% current inhibition (IC50) for the SR group was significantly different in pH 7.4 and pH 6.8 (24 vs. 74 μmol/L, P<0.01). The IC50 did not change significantly in CAF group when the pH decreased from 7.4 to 6.8.Conclusions During CAF, IK,ATP current density was increased and its allosteric modulation of ATP-sensitivity by intracellular pH was diminished.

  15. Polarized Parton Densities and Higher Twist in the Light of the Recent CLAS and COMPASS data

    CERN Document Server

    Leader, Elliot; Stamenov, Dimiter B

    2007-01-01

    The impact of the recent very precise CLAS and COMPASS g_1/F_1 data on polarized parton densities and higher twist effects is discussed. We demonstrate that the low Q^2 CLAS data improve essentially our knowledge of higher twist corrections to the spin structure function g1, while the large Q^2 COMPASS data influence mainly the strange quark and gluon polarizations which slightly decrease. We find also that the present inclusive DIS data cannot rule out a negative polarized and changing in sign gluon densities.

  16. Density-Driven Currents and Deposition of Fine Materials

    DEFF Research Database (Denmark)

    Saremi, Sina

    Dredging is a key element in river, ports, coastal and offshore development. In general dredging is conducted for excavation at the river,lake or seabed, relocation of the material, maintenance of the navigation channels, mining underwater deposits, land reclamation or cleaning up the environment....... Dredging activities always make changes to the environment, such as alteration of the coastal or river morphology, currents and wave climates, and water quality. Such changes may be considered improving or degrading to the environment. The type of material being dredged, type of the dredging equipment...... and type of sediments change along and into the seabed. Variations in the material entering the hopper have been studied by assuming fluctuating inflow concentrations. The fluctuations impose a mean net change on the overflow concentrations. In the third part of this study, the above described CFD model...

  17. Impact of CLAS and COMPASS data on Polarized Parton Densities and Higher Twist

    CERN Document Server

    Leader, E; Stamenov, D B; Leader, Elliot; Sidorov, Aleksander V.; Stamenov, Dimiter B.

    2006-01-01

    We have re-analyzed the world data on inclusive polarized DIS including the very precise CLAS proton and deuteron data, as well as the latest COMPASS data on the asymmetry $A_1^d$, and have studied the impact of these data on polarized parton densities and higher twist effects. We demonstrate that the low $Q^2$ CLAS data improve essentially our knowledge of higher twist corrections to the spin structure function $g_1$, while the large $Q^2$ COMPASS data influence mainly the strange quark density. In our new analysis we find that a negative polarized gluon density, or one that changes sign as a function of x, cannot be ruled out from the present DIS data.

  18. Non-perturbative calculation of molecular magnetic properties within current-density functional theory.

    Science.gov (United States)

    Tellgren, E I; Teale, A M; Furness, J W; Lange, K K; Ekström, U; Helgaker, T

    2014-01-21

    We present a novel implementation of Kohn-Sham density-functional theory utilizing London atomic orbitals as basis functions. External magnetic fields are treated non-perturbatively, which enable the study of both magnetic response properties and the effects of strong fields, using either standard density functionals or current-density functionals-the implementation is the first fully self-consistent implementation of the latter for molecules. Pilot applications are presented for the finite-field calculation of molecular magnetizabilities, hypermagnetizabilities, and nuclear magnetic resonance shielding constants, focusing on the impact of current-density functionals on the accuracy of the results. Existing current-density functionals based on the gauge-invariant vorticity are tested and found to be sensitive to numerical details of their implementation. Furthermore, when appropriately regularized, the resulting magnetic properties show no improvement over standard density-functional results. An advantage of the present implementation is the ability to apply density-functional theory to molecules in very strong magnetic fields, where the perturbative approach breaks down. Comparison with high accuracy full-configuration-interaction results show that the inadequacies of current-density approximations are exacerbated with increasing magnetic field strength. Standard density-functionals remain well behaved but fail to deliver high accuracy. The need for improved current-dependent density-functionals, and how they may be tested using the presented implementation, is discussed in light of our findings.

  19. Non-perturbative calculation of molecular magnetic properties within current-density functional theory

    Energy Technology Data Exchange (ETDEWEB)

    Tellgren, E. I., E-mail: erik.tellgren@kjemi.uio.no; Lange, K. K.; Ekström, U.; Helgaker, T. [Centre for Theoretical and Computational Chemistry, Department of Chemistry, University of Oslo, P.O. Box 1033 Blindern, N-0315 Oslo (Norway); Teale, A. M., E-mail: andrew.teale@nottingham.ac.uk [Centre for Theoretical and Computational Chemistry, Department of Chemistry, University of Oslo, P.O. Box 1033 Blindern, N-0315 Oslo (Norway); School of Chemistry, University of Nottingham, University Park, Nottingham NG7 2RD (United Kingdom); Furness, J. W. [School of Chemistry, University of Nottingham, University Park, Nottingham NG7 2RD (United Kingdom)

    2014-01-21

    We present a novel implementation of Kohn–Sham density-functional theory utilizing London atomic orbitals as basis functions. External magnetic fields are treated non-perturbatively, which enable the study of both magnetic response properties and the effects of strong fields, using either standard density functionals or current-density functionals—the implementation is the first fully self-consistent implementation of the latter for molecules. Pilot applications are presented for the finite-field calculation of molecular magnetizabilities, hypermagnetizabilities, and nuclear magnetic resonance shielding constants, focusing on the impact of current-density functionals on the accuracy of the results. Existing current-density functionals based on the gauge-invariant vorticity are tested and found to be sensitive to numerical details of their implementation. Furthermore, when appropriately regularized, the resulting magnetic properties show no improvement over standard density-functional results. An advantage of the present implementation is the ability to apply density-functional theory to molecules in very strong magnetic fields, where the perturbative approach breaks down. Comparison with high accuracy full-configuration-interaction results show that the inadequacies of current-density approximations are exacerbated with increasing magnetic field strength. Standard density-functionals remain well behaved but fail to deliver high accuracy. The need for improved current-dependent density-functionals, and how they may be tested using the presented implementation, is discussed in light of our findings.

  20. Variation of Eddy Current Density Distribution and its Effect on Crack Signal in Eddy Current Non-Destructive of Testing

    Directory of Open Access Journals (Sweden)

    Ladislav Janousek

    2006-01-01

    Full Text Available The paper deals with variation of eddy current density distribution along material depth and investigates an effect of the variation on a crack signal in eddy current non-destructive testing. Four coaxial rectangular tangential coils are used to induce eddy currents in a tested conductive object. The exciting coils are driven independently by phase-shifted AC currents; a ratio of amplitudes of the exciting currents is continuously changed to vary the distribution of eddy current density along material depth under a circular pick-up coil positioned in centre between the exciting coils. Dependences of a crack signal amplitude and its phase on the ratio are evaluated and special features are extracted. It is revealed that the dependences are strongly influenced by depth of a crack, and thus the extracted features can enhance evaluation of a detected crack.

  1. The Effect of Ion Current Density on Target Etching in Radio Frequency-Magnetron Sputtering Process

    Institute of Scientific and Technical Information of China (English)

    王庆; 王永富; 巴德纯; 岳向吉

    2012-01-01

    The effect of ion current density of argon plasma on target sputtering in magnetron sputtering process was investigated. Using home-made ion probe with computer-based data acquisition system, the ion current density as functions of discharge power, gas pressure and positions was measured. A double-hump shape was found in ion current density curve after the analysis of the effects of power and pressure. The data demonstrate that ion current density increases with the increase in gas pressure in spite of slightly at the double-hump site, sharply at wave-trough and side positions. Simultaneously, the ion current density increases upon increase in power. Es- pecially, the ion current density steeply increases at the double-hump site. The highest energy of the secondary electrons arising from Larmor precession was found at the double-hump position, which results in high ion density. The target was etched seriously at the double-hump position due to the high ion density there. The data indicates that the increase in power can lead to a high sputtering speed rate.

  2. Vortex-lattice pinning and critical current density in anisotropic high-temperature superconductors

    Science.gov (United States)

    Li, Yingxu; Li, Xiangyu; Kang, Guozheng; Gao, Yuanwen

    2016-10-01

    The anisotropy of critical current density is an impressive manifestation in the physics of high-temperature superconductors. We develop an analytical characterization of anisotropic flux-lattice pinning and critical current density in a system of random point defects. The effect of superconducting anisotropy on the pinning force and critical current density is formulated. The in-plane/out-of-plane anisotropy and microscopic characteristic lengths are incorporated in the field and angular dependence of the critical current density. This is helpful in understanding the physical essence of the scaling behavior in the experiments for critical current anisotropy. We discuss the role of strong and weak point defects in the anisotropic flux-lattice pinning. Relevance of the theory to the critical-state model is dictated as well.

  3. High Current Density and Low Thermal Conductivity of Atomically Thin Semimetallic WTe2.

    Science.gov (United States)

    Mleczko, Michal J; Xu, Runjie Lily; Okabe, Kye; Kuo, Hsueh-Hui; Fisher, Ian R; Wong, H-S Philip; Nishi, Yoshio; Pop, Eric

    2016-08-23

    Two-dimensional (2D) semimetals beyond graphene have been relatively unexplored in the atomically thin limit. Here, we introduce a facile growth mechanism for semimetallic WTe2 crystals and then fabricate few-layer test structures while carefully avoiding degradation from exposure to air. Low-field electrical measurements of 80 nm to 2 μm long devices allow us to separate intrinsic and contact resistance, revealing metallic response in the thinnest encapsulated and stable WTe2 devices studied to date (3-20 layers thick). High-field electrical measurements and electrothermal modeling demonstrate that ultrathin WTe2 can carry remarkably high current density (approaching 50 MA/cm(2), higher than most common interconnect metals) despite a very low thermal conductivity (of the order ∼3 Wm(-1) K(-1)). These results suggest several pathways for air-stable technological viability of this layered semimetal.

  4. Current density and conductivity through modified gravity in the graphene with defects

    CERN Document Server

    Sepehri, Alireza; Bamba, Kazuharu; Capozziello, Salvatore; Saridakis, Emmanuel N

    2016-01-01

    We propose a model describing the evolution of the free electron current density in graphene. Based on the concept of Mp-branes, we perform the analysis using the difference between curvatures of parallel and antiparallel spins. In such a framework an effective graviton emerges in the form of gauge field exchange between electrons. In a plain graphene system, the curvatures produced by both kinds of spins neutralize each other. However, in the presence of defects, the inequality between curvatures leads to the emergence of current density, modified gravity and conductivity. Depending on the type of the defects, the resulting current density can be negative or positive.

  5. Depairing current density through a low-angle grain boundary in a superconducting film

    Directory of Open Access Journals (Sweden)

    Feng Xue

    2016-05-01

    Full Text Available In this paper, the effect of a grain boundary (GB on the depairing current density of a high-temperature superconducting film is investigated. The modified effective free energy is proposed by considering the interaction of the superconducting condensate with the deformation of the superconductor due to the dislocations which constitute a grain boundary. After the elastic strain field of the dislocation is obtained, we analyzed the depress effect of the GB on the depairing current density of a superconducting film. The results are qualitatively agreement with the classic exponential relationship with the misorientation angles of the critical current density of high-temperature superconductors.

  6. Effects of Electron Flow Current Density on Flow Impedance of Magnetically Insulated Transmission Lines

    Institute of Scientific and Technical Information of China (English)

    HE Yong; ZOU Wen-Kang; SONG Sheng-Yi

    2011-01-01

    @@ In modern pulsed power systems, magnetically insulated transmission lines (MITLs) are used to couple power between the driver and the load.The circuit parameters of MITLs are well understood by employing the concept of Sow impedance derived from Maxwell's equations and pressure balance across the flow.However, the electron density in an MITL is always taken as constant in the application of flow impedance.Thus effects of electron flow current density (product of electron density and drift velocity) in an MITL are neglected.We calculate the flow impedances of an MITL and compare them under three classical MITL theories, in which the electron density profile and electron flow current density are different from each other.It is found that the assumption of constant electron density profile in the calculation of the Sow impedance is not always valid.The electron density profile and the electron flow current density have significant effects on flow impedance of the MITL.The details of the electron flow current density and its effects on the operation impedance of the MITL should be addressed more explicitly experiments and theories in the future.

  7. Electromigration in Sn–Ag solder thin films under high current density

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, X. [School of Computing and Mathematical Sciences, University of Greenwich, 30 Park Row, London SE10 9LS (United Kingdom); Kotadia, H. [Physics Department, School of Natural and Mathematical Sciences, King' s College London, Strand, London WC2R 2LS (United Kingdom); Xu, S. [Department of Electronic Engineering, City University of Hong Kong, 83 Tat Chee Avenue, Kow-loon Tong, Hong Kong (China); Lu, H. [School of Computing and Mathematical Sciences, University of Greenwich, 30 Park Row, London SE10 9LS (United Kingdom); Mannan, S.H. [Physics Department, School of Natural and Mathematical Sciences, King' s College London, Strand, London WC2R 2LS (United Kingdom); Bailey, C. [School of Computing and Mathematical Sciences, University of Greenwich, 30 Park Row, London SE10 9LS (United Kingdom); Chan, Y.C. [Department of Electronic Engineering, City University of Hong Kong, 83 Tat Chee Avenue, Kow-loon Tong, Hong Kong (China)

    2014-08-28

    The electro-migration behavior of a Sn–Ag solder thin film stripe that is deposited on a glass substrate has been investigated under a high current density in the absence ofthermo-migration. The distribution of voids and hillocks at current densities of 4.4–6.0 × 10{sup 4} A/cm{sup 2} has been analyzed optically and using electron microscopy. The voids mainly formed at the cathode side of the stripe where maximum current density was predicted but voids also formed along a line that crosses the stripe. This was explained in terms of the initial voids forming at locations of maximum current density concentration, altering these locations, and then expanding into them. The movement of the maximum current density location is caused by redistribution of current as the voids form. An atomic migration model has been developed and used in this work. It was found that if thermal gradients were completely neglected, the model was unable to account for the divergence of atomic flux density which is necessary for void nucleation. However, the temperature dependence of the diffusivity of atoms is sufficient to account for void nucleation within the timescale of the experiments. - Highlights: • Experimental and computational study of electron migration in a SnAg film • The calculated atomic flux divergence has been used to predict void formation. • Voids caused by electromigration observed at current crowding sites and in other regions.

  8. Definition of current density in the presence of a non-local potential.

    Science.gov (United States)

    Li, Changsheng; Wan, Langhui; Wei, Yadong; Wang, Jian

    2008-04-16

    In the presence of a non-local potential arising from electron-electron interaction, the conventional definition of current density J(c) = (e/2m)([(p-eA)ψ](*)ψ-ψ(*)[(p-eA)ψ]) cannot satisfy the condition of current conservation, i.e., [Formula: see text] in the steady state. In order to solve this problem, we give a new definition of current density including the contribution due to the non-local potential. We show that the current calculated based on the new definition of current density conserves the current and is the same as that obtained from the Landauer-Büttiker formula. Examples are given to demonstrate our results.

  9. Ion density and dielectric breakdown in the afterglow of a high-current arc discharge

    Energy Technology Data Exchange (ETDEWEB)

    Rutgers, W.R.; Verhagen, F.C.M.; De Zeeuw, W.A.

    1984-01-01

    The ion density in the afterglow of a high-current atmospheric arc-discharge and electrical breakdown have been investigated in atomic (argon), molecular (nitrogen) and electronegative (carbon dioxide) media. From the decay with time of the ion density, effective recombination coefficients can be calculated. When the ion density is reduced to values below 2 x 10/sup 17/m/sup -3/, the afterglow plasma changes from a resistive into a dielectric medium. (J.C.R.)

  10. A Galvanostatic Modeling for Preparation of Electrodeposited Nanocrystalline Coatings by Control of Current Density

    Institute of Scientific and Technical Information of China (English)

    Ali Mohammad Rashidi

    2012-01-01

    The correlation between the grain size of electrodeposited coatings and the current densities was modeled by considering galvanostatic conditions. In order to test the model by experimental results, nanocrystalline (NC) nickel samples were deposited at different current densities using a Watts bath. The grain size of the deposits was evaluated by X-ray diffraction (XRD) technique. Model predictions were validated by finding a curve being the best-fit to the experimental results which were gathered from literature for different NC coatings in addition to those data measured in this research for NC nickel coatings. According to our model, the variation of grain size with the reciprocal of the current density follows a power law. A good agreement between the experimental results and model predictions was observed which indicated that the derived analytical model is applicable for producting the nanocrystalline electrodeposits with the desired grain size by controling current density.

  11. Flux quantum tunneling effect and its influence on the experimental critical current density

    Institute of Scientific and Technical Information of China (English)

    闻海虎; 赵忠贤; GriessenR.

    1995-01-01

    By using magnetic sweeping method, the temperature and magnetic field dependencies of the experimental current density and the normalized relaxation rate have been obtained. The true critical current density corresponding to the zero activation energy has been carried out based on the collective-pinning and the thermally-activated flux motion models, and therefore the influences of the quantum tunneling effect and the thermal activation effect on the experimental critical current density are distinguished. It is found that, with temperature lower than 10 K, the relaxation rate will not drop to zero when T approaches zero K because of the occurrence of the flux quantum tunneling. This additional flux motion further reduces the experimental critical current density j making it saturated with lowering temperature.

  12. Charge Exchange Effect on Space-Charge-Limited Current Densities in Ion Diode

    Institute of Scientific and Technical Information of China (English)

    石磊

    2002-01-01

    The article theoretically studied the charge-exchange effects on space charge limited electron and ion current densities of non-relativistic one-dimensional slab ion diode, and compared with those of without charge exchange.

  13. Fresh water-salt water density currents, a major cause of siltation in estuaries

    National Research Council Canada - National Science Library

    Schultz, E.A; Simmons, H.B

    1957-01-01

    ... the effects of changing the upland discharge into estuaries, rivers, and harbours where the fresh water-salt water density currents are present in some degree, and in some cases are the major cause of siltation; and 4...

  14. 4-Component relativistic calculation of the magnetically induced current density in the group 15 heteroaromatic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Bast, Radovan; Juselius, Jonas [Centre for Theoretical and Computational Chemistry (CTCC), Department of Chemistry, University of Tromso, N-9037 Tromso (Norway); Saue, Trond [Institut de Chimie de Strasbourg, CNRS et Universite Louis Pasteur, Laboratoire de Chimie Quantique, 4, rue Blaise Pascal, BP 1032, F-67070 Strasbourg (France)], E-mail: tsaue@chimie.u-strasbg.fr

    2009-02-17

    We present a 4-component relativistic implementation for calculating the magnetically induced current density within Hartree-Fock and Kohn-Sham linear response theory using a common gauge origin. We demonstrate how the current density can be decomposed into paramagnetic and diamagnetic contributions by calculating separately the contributions from rotations between positive-energy orbitals and contributions from rotations between the occupied positive-energy orbitals and the virtual negative-energy orbitals, respectively. This methodology is applied to the study of the magnetically induced current density in benzene and the group 15 heteroaromatic compounds C{sub 5}H{sub 5}E (E = N, P, As, Sb, Bi). Quantitative values for the magnetically induced ring currents are obtained by numerical integration over the current flow. We have found that the diatropic ring current is sustained for the entire series of the group 15 heteroaromatic compounds-the induced ring current susceptibility of bismabenzene being 76% of the benzene result. Having employed two hybrid and two nonhybrid generalized gradient approximation functionals, the results are found to be rather insensitive to the choice of the density functional approximation. The relativistic effect is relatively small, reaching its maximum of 8% for bismabenzene. The presented 4-component relativistic methodology opens up the possibility to visualize magnetically induced current densities of aromatic heavy-element systems with both scalar relativistic and spin-orbit effects included.

  15. Switching current density reduction in perpendicular magnetic anisotropy spin transfer torque magnetic tunneling junctions

    Energy Technology Data Exchange (ETDEWEB)

    You, Chun-Yeol [Department of Physics, Inha University, Incheon 402-751 (Korea, Republic of)

    2014-01-28

    We investigate the switching current density reduction of perpendicular magnetic anisotropy spin transfer torque magnetic tunneling junctions using micromagnetic simulations. We find that the switching current density can be reduced with elongated lateral shapes of the magnetic tunnel junctions, and additional reduction can be achieved by using a noncollinear polarizer layer. The reduction is closely related to the details of spin configurations during switching processes with the additional in-plane anisotropy.

  16. Influence of current density on microstructure of pulse electrodeposited tin coatings

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Ashutosh; Bhattacharya, Sumit; Sen, Ranjan; Reddy, B.S.B. [Department of Metallurgical and Materials Engineering, Indian Institute of Technology-Kharagpur, Kharagpur-721302 (India); Fecht, H.-J. [Institut fuer Mikro- und Nanomaterialien, Universitaet Ulm, D-89081 Ulm (Germany); Das, Karabi, E-mail: karabi@metal.iitkgp.ernet.in [Department of Metallurgical and Materials Engineering, Indian Institute of Technology-Kharagpur, Kharagpur-721302 (India); Das, Siddhartha [Department of Metallurgical and Materials Engineering, Indian Institute of Technology-Kharagpur, Kharagpur-721302 (India)

    2012-06-15

    Pulse electrodeposited tin coatings on copper substrate have been synthesized from an aqueous solution containing sodium stannate (Na{sub 2}SnO{sub 3}.3H{sub 2}O) and sodium hydroxide (NaOH). The effect of current density on surface morphology of the deposits has been investigated. As deposited coatings are characterized by X-ray diffraction, scanning electron microscopy, electron backscatter diffraction, and line profile analysis. The X-ray diffraction analysis shows that the deposits consist of tetragonal ({beta}-Sn) structure with microcrystalline grains. The deposits plated at lower current density exhibit (110) texture which decreases with increasing current densities. The effects of current density on Cu-Sn diffusion and whisker growth of the electrodeposited tin coatings are also reported here. - Highlights: Black-Right-Pointing-Pointer Pulse electrodeposition of Sn from aqueous alkaline solution without adding any organic additive. Black-Right-Pointing-Pointer Effect of current density on morphology and whisker growth in tin coatings aged for 1 year. Black-Right-Pointing-Pointer Solution bath is stable and can be operated over a wide range of current density.

  17. Experimental study of the velocity of density currents in convergent and divergent channels

    Institute of Scientific and Technical Information of China (English)

    Hasan Torabi POUDEH; Samad EMAMGHOLIZADEH; Manoocher Fathi-MOGHADAM

    2014-01-01

    The head velocity of the density current in the convergent and divergent channel is a key parameter for evaluating the extent to which suspended material travels, and for determining the type and distribution of sediment in the water body. This study experimentally evaluated the effects of the reach degree of convergence and divergence on the head velocity of the density current. Experiments were conducted in the flume with 6.0 m long, 0.72 m width and 0.6 m height. The head velocity was measured at three convergent degrees (-8o;-12o;-26o), at three divergent degrees (8o; 12o; 26o) and two slopes (0.009, 0.016) for various discharges. The measured head velocity of the density current is compared with the head velocity of the density current in the constant cross section channel. Based on non-dimensional and statistical analysis, relations as linear multiple regression are offered for predicting head velocity of the density current in the convergent, divergent and constant cross section channel. Also the results of this research show that for the same slope and discharge, the head velocity of the density current in the convergent and divergent channel are greater and less than the head velocity of the constant cross section, respectively.

  18. Higher spin currents in the N =2 stringy coset minimal model

    Science.gov (United States)

    Ahn, Changhyun

    2016-12-01

    In the coset model based on (AN-1 (1 )⊕AN-1 (1 ),AN-1 (1 )) at level (N ,N ;2 N ), it is known that the N =2 superconformal algebra can be realized by the two kinds of adjoint fermions. Each Kac-Moody current of spin 1 is given by the product of fermions with structure constant (f symbols) as usual. One can construct the spin-1 current by combining the above two fermions with the structure constant and the spin-1 current by multiplying these two fermions with a completely symmetric S U (N ) invariant tensor of rank 3 (d symbols). The lowest higher spin-2 current with nonzero U (1 ) charge (corresponding to the zero mode eigenvalue of the spin-1 current of N =2 superconformal algebra) can be obtained from these four spin-1 currents in quadratic form. Similarly, the other type of lowest higher spin-2 current, whose U (1 ) charge is opposite to the above one, can be obtained also. Four higher spin-5/2 currents can be constructed from the operator product expansions (OPEs) between the spin-3/2 currents of N =2 superconformal algebra and the above two higher spin-2 currents. The two higher spin-3 currents can be determined by the OPEs between the above spin-3/2 currents and the higher spin-5/2 currents. Finally, the ten N =2 OPEs between the four N =2 higher spin multiplets (2 ,5/2 ,5/2 ,3 ) , (2 ,5/2 ,5/2 ,3 ) , (7/2 ,4 ,4 ,9/2 ) , and (7/2 ,4 ,4 ,9/2 ) are obtained explicitly for generic N .

  19. Higher-order adaptive finite-element methods for Kohn-Sham density functional theory

    CERN Document Server

    Motamarri, Phani; Leiter, Kenneth; Knap, Jaroslaw; Gavini, Vikram

    2012-01-01

    We present an efficient computational approach to perform real-space electronic structure calculations using an adaptive higher-order finite-element discretization of Kohn-Sham density-functional theory (DFT).To this end, we develop an \\emph{a priori} mesh adaption technique to construct a close to optimal finite-element discretization of the problem. We further propose an efficient solution strategy for solving the discrete eigenvalue problem by using spectral finite-elements in conjunction with Gauss-Lobatto quadrature, and a Chebyshev acceleration technique for computing the occupied eigenspace. Using the proposed solution procedure, we investigate the computational efficiency afforded by higher-order finite-element discretizations of the Kohn-Sham DFT problem. Our studies suggest that staggering computational savings---of the order of $1000-$fold---can be realized, for both all-electron and pseudopotential calculations, by using higher-order finite-element discretizations. On all the benchmark systems stu...

  20. Numerical Simulation of Current Density Distribution in Keyhole Double-Sided Arc Welding

    Institute of Scientific and Technical Information of China (English)

    Junsheng SUN; Chuansong WU; Min ZHANG; Houxiao WANG

    2004-01-01

    In the double-sided arc welding system (DSAW) composing of PAW+TIG arcs, the PAW arc is guided by the TIG arc so that the current mostly flows through the direction of the workpiece thickness and the penetration is greatly improved. To analyze the current density distribution in DSAW is beneficial to understanding of this process.Considering all kinds of dynamic factors acting on the weldpool, this paper discusses firstly the surface deformation of the weldpool and the keyhole formation in PAW+TIG DSAW process on the basis of the magnetohydrodynamic theory and variation principles. Hence, a model of the current density distribution is developed. Through numerical simulation, the current density distribution in PAW+TIG DSAW process is quantitatively analyzed. It shows that the minimal radius of keyhole formed in PAW+TIG DSAW process is 0.5 mm and 89.5 percent of current flows through the keyhole.

  1. Interaction of pyroclastic density currents with human settlements: Evidence from ancient Pompeii

    Science.gov (United States)

    Gurioli, Lucia; Pareschi, M. Teresa; Zanella, Elena; Lanza, Roberto; Deluca, Enrico; Bisson, Marina

    2005-06-01

    Integrating field observations and rock-magnetic measurements, we report how a turbulent pyroclastic density current interacted with and moved through an urban area. The data are from the most energetic, turbulent pyroclastic density current of the A.D. 79 eruption of Vesuvius, Italy, which partially destroyed the Roman city of Pompeii. Our results show that the urban fabric was able to divide the lower portion of the current into several streams that followed the city walls and the intracity roads. Vortices, revealed by upstream particle orientations and decreases in deposit temperature, formed downflow of obstacles or inside cavities. Although these perturbations affected only the lower part of the current and were localized, they could represent, in certain cases, cooler zones within which chances of human survival are increased. Our integrated field data for pyroclastic density current temperature and flow direction, collected for the first time across an urban environment, enable verification of coupled thermodynamic numerical models and their hazard simulation abilities.

  2. A fast, calibrated model for pyroclastic density currents kinematics and hazard

    Science.gov (United States)

    Esposti Ongaro, Tomaso; Orsucci, Simone; Cornolti, Fulvio

    2016-11-01

    Multiphase flow models represent valuable tools for the study of the complex, non-equilibrium dynamics of pyroclastic density currents. Particle sedimentation, flow stratification and rheological changes, depending on the flow regime, interaction with topographic obstacles, turbulent air entrainment, buoyancy reversal, and other complex features of pyroclastic currents can be simulated in two and three dimensions, by exploiting efficient numerical solvers and the improved computational capability of modern supercomputers. However, numerical simulations of polydisperse gas-particle mixtures are quite computationally expensive, so that their use in hazard assessment studies (where there is the need of evaluating the probability of hazardous actions over hundreds of possible scenarios) is still challenging. To this aim, a simplified integral (box) model can be used, under the appropriate hypotheses, to describe the kinematics of pyroclastic density currents over a flat topography, their scaling properties and their depositional features. In this work, multiphase flow simulations are used to evaluate integral model approximations, to calibrate its free parameters and to assess the influence of the input data on the results. Two-dimensional numerical simulations describe the generation and decoupling of a dense, basal layer (formed by progressive particle sedimentation) from the dilute transport system. In the Boussinesq regime (i.e., for solid mass fractions below about 0.1), the current Froude number (i.e., the ratio between the current inertia and buoyancy) does not strongly depend on initial conditions and it is consistent to that measured in laboratory experiments (i.e., between 1.05 and 1.2). For higher density ratios (solid mass fraction in the range 0.1-0.9) but still in a relatively dilute regime (particle volume fraction lower than 0.01), numerical simulations demonstrate that the box model is still applicable, but the Froude number depends on the reduced

  3. A carbon nanotube field emission cathode with high current density and long-term stability

    Science.gov (United States)

    Calderón-Colón, Xiomara; Geng, Huaizhi; Gao, Bo; An, Lei; Cao, Guohua; Zhou, Otto

    2009-08-01

    Carbon nanotube (CNT) field emitters are now being evaluated for a wide range of vacuum electronic applications. However, problems including short lifetime at high current density, instability under high voltage, poor emission uniformity, and pixel-to-pixel inconsistency are still major obstacles for device applications. We developed an electrophoretic process to fabricate composite CNT films with controlled nanotube orientation and surface density, and enhanced adhesion. The cathodes have significantly enhanced macroscopic field emission current density and long-term stability under high operating voltages. The application of this CNT electron source for high-resolution x-ray imaging is demonstrated.

  4. Simultaneous visualization of oxygen partial pressure, current density, and water droplets in serpentine fuel cell during power generation for understanding reaction distributions

    Science.gov (United States)

    Takanohashi, Kazuhiro; Suga, Takeo; Uchida, Makoto; Ueda, Toshihide; Nagumo, Yuzo; Inukai, Junji; Nishide, Hiroyuki; Watanabe, Masahiro

    2017-03-01

    Understanding the reaction distributions inside a polymer electrolyte fuel cell (PEFC) is essential for the higher performance and durability. We have developed a new see-through cell and visualized the distributions of oxygen partial pressure and current density inside a running PEFC at the temperature of 40 and 80 °C and the relative humidity of 53%. The oxygen utilization was changed from 0% to 80% by changing the current density. At higher oxygen utilizations, the current density was higher and therefore the water generation. Generated water droplets in the flow channel were also visualized, allowing for the simultaneous visualization of the distribution of the oxygen partial pressure, current density, and water droplets. By combining the observations of all three parameters, the reactions inside a membrane-electrode assembly were discussed.

  5. A comparison of different methods to implement higher order derivatives of density functionals

    Energy Technology Data Exchange (ETDEWEB)

    van Dam, Hubertus J.J. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-05-18

    Density functional theory is the dominant approach in electronic structure methods today. To calculate properties higher order derivatives of the density functionals are required. These derivatives might be implemented manually,by automatic differentiation, or by symbolic algebra programs. Different authors have cited different reasons for using the particular method of their choice. This paper presents work where all three approaches were used and the strengths and weaknesses of each approach are considered. It is found that all three methods produce code that is suffficiently performanted for practical applications, despite the fact that our symbolic algebra generated code and our automatic differentiation code still have scope for significant optimization. The automatic differentiation approach is the best option for producing readable and maintainable code.

  6. Current density imaging using directly measured harmonic Bz data in MREIT.

    Science.gov (United States)

    Park, Chunjae; Kwon, Oh In

    2013-01-01

    Magnetic resonance electrical impedance tomography (MREIT) measures magnetic flux density signals through the use of a magnetic resonance imaging (MRI) in order to visualize the internal conductivity and/or current density. Understanding the reconstruction procedure for the internal current density, we directly measure the second derivative of Bz data from the measured k-space data, from which we can avoid a tedious phase unwrapping to obtain the phase signal of Bz . We determine optimal weighting factors to combine the derivatives of magnetic flux density data, [Symbol: see text](2) Bz , measured using the multi-echo train. The proposed method reconstructs the internal current density using the relationships between the induced internal current and the measured [Symbol: see text](2) Bz data. Results from a phantom experiment demonstrate that the proposed method reduces the scanning time and provides the internal current density, while suppressing the background field inhomogeneity. To implement the real experiment, we use a phantom with a saline solution including a balloon, which excludes other artifacts by any concentration gradient in the phantom.

  7. An adaptive finite element approach to modelling sediment laden density currents

    Science.gov (United States)

    Parkinson, S.; Hill, J.; Allison, P. A.; Piggott, M. D.

    2012-04-01

    Modelling sediment-laden density currents at real-world scales is a challenging task. Here we present Fluidity, which uses dynamic adaptive re-meshing to reduce computational costs whilst maintaining sufficient resolution where and when it is required. This allows small-scale processes to be captured in large scale simulations. Density currents, also known as gravity or buoyancy currents, occur wherever two fluids with different densities meet. They can occur at scales of up to hundred kilometres in the ocean when continental shelves collapse. This process releases large quantities of sediment into the ocean which increase the bulk density of the fluid to form a density current. These currents can carry sediment hundreds of kilometres, at speeds of up to a hundred kilometres per hour, over the sea bed. They can be tsunamigenic and they have the potential to cause significant damage to submarine infrastructure, such as submarine telecommunications cables or oil and gas infrastructure. They are also a key process for movement of organic material into the depths of the ocean. Due to this, they play an important role in the global carbon cycle on the Earth, forming a significant component of the stratigraphic record, and their deposits can form useful sources of important hydrocarbons. Modelling large scale sediment laden density currents is a very challenging problem. Particles within the current are suspended by turbulence that occurs at length scales that are several orders of magnitude smaller than the size of the current. Models that resolve the vertical structure of the flow require a very large, highly resolved mesh, and substantial computing power to solve. Here, we verify our adaptive model by comparison with a set of laboratory experiments by Gladstone et al. [1998] on the propagation and sediment deposition of bidisperse gravity currents. Comparisons are also made with fixed mesh solutions, and it is shown that accuracy can be maintained with fewer elements

  8. Measurement of induced magnetic flux density using injection current nonlinear encoding (ICNE) in MREIT.

    Science.gov (United States)

    Park, Chunjae; Lee, Byung Il; Kwon, Ohin; Woo, Eung Je

    2007-02-01

    Magnetic resonance electrical impedance tomography (MREIT) measures induced magnetic flux densities subject to externally injected currents in order to visualize conductivity distributions inside an electrically conducting object. Injection currents induce magnetic flux densities that appear in phase parts of acquired MR image data. In the conventional current injection method, we inject currents during the time segment between the end of the first RF pulse and the beginning of the reading gradient in order to ensure the gradient linearity. Noting that longer current injections can accumulate more phase changes, we propose a new pulse sequence called injection current nonlinear encoding (ICNE) where the duration of the injection current pulse is extended until the end of the reading gradient. Since the current injection during the reading gradient disturbs the gradient linearity, we first analyze the MR signal produced by the ICNE pulse sequence and suggest a novel algorithm to extract the induced magnetic flux density from the acquired MR signal. Numerical simulations and phantom experiments show that the new method is clearly advantageous in terms of the reduced noise level in measured magnetic flux density data. The amount of noise reduction depends on the choice of the data acquisition time and it was about 24% when we used a prolonged data acquisition time of 10.8 ms. The ICNE method will enhance the clinical applicability of the MREIT technique when it is combined with an appropriate phase artefact minimization method.

  9. Can the current density map topology be extracted from the nucleus independent chemical shifts?

    NARCIS (Netherlands)

    Van Damme, Sofie; Acke, Guillaume; Havenith, Remco W. A.; Bultinck, Patrick

    2016-01-01

    Aromatic compounds are characterised by the presence of a ring current when in a magnetic field. As a consequence, current density maps are used to assess (the degree of) aromaticity of a compound. However, often a more discrete set of so-called Nucleus Independent Chemical Shift (NICS) values is us

  10. Experimental determination of two-dimensional critical current density distribution in YBCO coated conductors

    Energy Technology Data Exchange (ETDEWEB)

    Amemiya, Naoyuki; Shinkai, Yoshichika [Faculty of Engineering, Yokohama National University, Tokiwadai, Hodogaya, Yokohama (Japan); Iijima, Yasuhiro; Kakimoto, Kazuomi; Takeda, Kaoru [Materials Research Laboratory, Fujikura Ltd., Kiba, Koto, Tokyo (Japan)

    2001-08-01

    The critical current density (J{sub c}) distribution in YBCO coated conductors is attracting interest from the viewpoint of its influence on their AC loss characteristics as well as from material science and process engineering. A two-dimensional J{sub c} distribution in a YBCO coated conductor made by the IBAD (ion-beam assisted deposition) and the PLD (pulse-laser deposition) method can be determined by the magnetic-knife method with spatial resolutions of 0.2 mm lateral and 10 mm longitudinal directions, respectively. In an up-to-date 80A-class YBCO coated conductor, the J{sub c} is relatively uniform in the central part and reaches mbox{l_brace}7$x$10{sup 9} A m{sup -2}, {r_brace} while the J{sub c} fluctuates spatially in the central part of a tape fabricated earlier and with less critical current. Near the edges of the tapes, the J{sub c} is higher or lower than in the central part and the experimentally determined J{sub c} distributions are far from uniform. This suggests that a presumption of a uniform J{sub c} for AC loss estimations is not always reasonable and can lead to a large error in the estimated AC losses. (author)

  11. Physical and Mechanical Characterization of Electrodeposited Nickel Nanowires -- Influence of Current Density and External Magnetic Field

    Science.gov (United States)

    Samykano, Mahendran

    insights from the present experimental research include: Electrodeposition method consistently synthesizes high purity Ni nanowires (98% and higher based on energy dispersive spectroscopy (EDS)) with a significant improvement in surface morphology when magnetic field is present during synthesis; X-ray diffraction (XRD) characterization and analysis indicate that electric current density has significant influence on the crystal orientation of Ni nanowire, while a decrease in crystal size was noticed with increased magnetic field intensity for same current densities. Carefully studied uni-axial tensile characterization using MEMS tensile loading device indicates an increase in elastic tensile modulus when the magnetic field is present during electrodeposition and consistent observation of three different variants of ductile failure modes. Results and discussions of tensile stress-strain mechanical characteristics of Ni nanowires and their failure modes provide key research findings that are not currently available in the literature to our knowledge. The present research contributes to the experimental understanding of tensile deformation of Ni nanowires, as well as developing and presenting a robust experimental methodology for future extension to other metallic nanowires. Research findings clearly illustrate a need for three-dimensional high fidelity experimental tools and relevant computational modeling for a full understanding and insight on deformation and failure mechanisms involved at nanoscale.

  12. Flow Transformation in Pyroclastic Density Currents: Entrainment and Granular Dynamics during the 2006 eruption of Tungurahua

    Science.gov (United States)

    Dufek, J.; Benage, M. C.; Geist, D.; Harpp, K. S.

    2013-12-01

    Pyroclastic density currents are ground hugging flows composed of hot gases, fragments of juvenile magmatic material, and entrained clasts from the conduit or the edifice over which the flows have traveled. The interior of these flows are opaque to observation due to their large ash content, but recent investigations have highlighted that there are likely strong gradients in particle concentration and segregation of particle sizes in these particle-laden gravity currents. Pyroclastic density currents refer to a broad range of phenomena from dense flows in which the dynamics are dominated by frictional interaction between particles (dense granular flows), to gas fluidized flows, to dilute flows dominated by particle-gas turbulent interaction. However, abrupt flow transformation (e.g. from dense to dilute pyroclastic density currents) can arise due to energy exchange across multiple length scales and phases, and understanding these flow transformations is important in delineating the entrainment and erosion history of these flows, interpretations of their deposits, and in better understanding the hazards they present. During the 2006 eruption of Tungurahua, Ecuador numerous, dense pyroclastic density currents descended the volcano as result of boiling-over or low column collapse eruptions. The deposits of these flows typically have pronounced snouts and levees, and are often dominated by large, clasts (meter scale in some locations). There is an exceptional observational record of these flows and their deposits, permitting detailed field constraints of their dynamics. A particularly interesting set of flows occurred on Aug. 17, 2006 during the paroxysmal phase of the eruption that descended the slope of the volcano, filled in the river channel of the Chambo river, removing much of the larger clasts from the flow, and resulting in a dilute ';surge' that transported finer material across the channel and uphill forming dune features on the opposite bank of the river. We

  13. Calculations of current densities for neutral and doubly charged persubstituted benzenes using effective core potentials.

    Science.gov (United States)

    Rauhalahti, Markus; Taubert, Stefan; Sundholm, Dage; Liégeois, Vincent

    2017-03-08

    Magnetically induced current density susceptibilities and ring-current strengths have been calculated for neutral and doubly charged persubstituted benzenes C6X6 and C6X6(2+) with X = F, Cl, Br, I, At, SeH, SeMe, TeH, TeMe, and SbH2. The current densities have been calculated using the gauge-including magnetically induced current (GIMIC) method, which has been interfaced to the Gaussian electronic structure code rendering current density calculations using effective core potentials (ECP) feasible. Relativistic effects on the ring-current strengths have been assessed by employing ECP calculations of the current densities. Comparison of the ring-current strengths obtained in calculations on C6At6 and C6At6(2+) using relativistic and non-relativistic ECPs show that scalar relativistic effects have only a small influence on the ring-current strengths. Comparisons of the ring-current strengths and ring-current profiles show that the C6I6(2+), C6At6(2+), C6(SeH)6(2+), C6(SeMe)6(2+), C6(TeH)6(2+), C6(TeMe)6(2+), and C6(SbH2)6(2+) dications are doubly aromatic sustaining spatially separated ring currents in the carbon ring and in the exterior of the molecule. The C6I6(+) radical cation is also found to be doubly aromatic with a weaker ring current than obtained for the dication.

  14. Effect of the current density on electrodepositing alpha-lead dioxide coating on aluminum substrate

    Institute of Scientific and Technical Information of China (English)

    Burning CHEN; Zhongcheng GUO; Hui HUANG; Xianwan YANG; Yuandong CAO

    2009-01-01

    The α-PbO_2 electrodes are prepared by anodic electrodeposition on Al/conductive coating electrode from alkaline plumbite solutions in order to investigate the effect of the different current densities on the properties of α-PbO_2 electrodes. The physic-ochemical properties of the α-PbO_2 electrodes are analyzed by using SEM, EDS, XRD, Tafel plot, linear sweep voltammetry (LSV) and A.C. Impedance. A compact and uniform layer of lead dioxide was obtained at the current density of 3 mA-cm~(-2) . A further increase in current density results in smaller particles with high porosity. EDS and XRD analyses have shown that the PbO_2 deposited in alkaline conditions is highly non stoichiometric, and the PbO impurities are formed on the surface layer besides the α-PbO_2. The corrosion resistance of α-PbO_2 at the low current density is superior to that of the high current density. It can be attributed to a porous layer of deposited films at high current densities. When used as anodes for oxygen evolution in aqueous Zn~(2+) 50 g·L~(-1), H_2SO_4 150 g·L~(-1), the Al/conductive coating/α-PbO_2 exhibits lower potential compared to Pb electrode. Al/conductive coating/α-PbO_2 electrode with the best electrocatalytic activity was obtained at current density of 1 mA·cm~(-2). The lowest roughness factor was obtained at 1 mA·cm~(-2).

  15. Transport critical-current density of superconducting films with hysteretic ferromagnetic dots

    Directory of Open Access Journals (Sweden)

    Nuria Del-Valle

    2012-06-01

    Full Text Available Superconductor-ferromagnet hybrids present a rich and complex phenomenology. Particularly, a hysteretic behavior on the transport critical-current density, as a function of a uniform perpendicular applied field, has been experimentally found in superconducting films with some embedded ferromagnets. Here we analyze the interaction superconductor-ferromagnets by means of an iterative model based on the critical-state model with field-dependent internal critical-current density and compare the results with actual transport measurements. By using arguments of field compensation, we show how the change in the magnetization of the ferromagnetic inclusions is responsible for the observed hysteresis on the transport critical current.

  16. Selective regulation of current densities underlies spontaneous changes in the activity of cultured neurons.

    Science.gov (United States)

    Turrigiano, G; LeMasson, G; Marder, E

    1995-05-01

    We study the electrical activity patterns and the expression of conductances in adult stomatogastric ganglion (STG) neurons as a function of time in primary cell culture. When first plated in culture, these neurons had few active properties. After 1 d in culture they produced small action potentials that rapidly inactivated during maintained depolarization. After 2 d in culture they fired large action potentials tonically when depolarized, and their properties resembled very closely the properties of STG neurons pharmacologically isolated in the ganglion. After 3-4 d in culture, however, their electrical properties changed and they fired in bursts when depolarized. We characterized the currents expressed by these neurons in culture. They included two TTX-sensitive sodium currents, a calcium current, a delayed-rectifier-like current, a calcium-dependent potassium current, and two A-type currents. The changes in firing properties with time in culture were accompanied by an increase in inward and decrease in outward current densities. A single-compartment conductance-based model of an STG neuron was constructed by fitting the currents measured in the biological neurons. When the current densities in the model neuron were matched to those measured for the biological neurons in each activity state, the model neuron closely reproduced each state, indicating that the changes in current densities are sufficient to account for the changes in intrinsic properties. These data indicate that STG neurons isolated in culture change their intrinsic electrical properties by selectively adjusting the magnitudes of their ionic conductances.

  17. Gauge-Origin Independent Calculations of the Anisotropy of the Magnetically Induced Current Densities.

    Science.gov (United States)

    Fliegl, Heike; Jusélius, Jonas; Sundholm, Dage

    2016-07-21

    Gauge-origin independent current density susceptibility tensors have been computed using the gauge-including magnetically induced current (GIMIC) method. The anisotropy of the magnetically induced current density (ACID) functions constructed from the current density susceptibility tensors are therefore gauge-origin independent. The ability of the gauge-origin independent ACID function to provide quantitative information about the current flow along chemical bonds has been assessed by integrating the cross-section area of the ACID function in the middle of chemical bonds. Analogously, the current strength susceptibility passing a given plane through the molecule is obtained by numerical integration of the current flow parallel to the normal vector of the integration plane. The cross-section area of the ACID function is found to be strongly dependent on the exact location of the integration plane, which is in sheer contrast to the calculated ring-current strength susceptibilities that are practically independent of the chosen position of the integration plane. The gauge-origin independent ACID functions plotted for different isosurface values show that a visual assessment of the current flow and degree of aromaticity depends on the chosen isosurface. The present study shows that ACID functions are not an unambiguous means to estimate the degree of molecular aromaticity according to the magnetic criterion and to determine the current pathway of complex molecular rings.

  18. Direct mapping of local redox current density on a monolith electrode by laser scanning.

    Science.gov (United States)

    Lee, Seung-Woo; Lopez, Jeffrey; Saraf, Ravi F

    2013-09-15

    An optical method of mapping local redox reaction over a monolith electrode using simple laser scanning is described. As the optical signal is linearly proportional to the maximum redox current that is measured concomitantly by voltammetry, the optical signal quantitatively maps the local redox current density distribution. The method is demonstrated on two types of reactions: (1) a reversible reaction where the redox moieties are ionic, and (2) an irreversible reaction on two different types of enzymes immobilized on the electrode where the reaction moieties are nonionic. To demonstrate the scanning capability, the local redox behavior on a "V-shaped" electrode is studied where the local length scale and, hence, the local current density, is nonuniform. The ability to measure the current density distribution by this method will pave the way for multianalyte analysis on a monolith electrode using a standard three-electrode configuration. The method is called Scanning Electrometer for Electrical Double-layer (SEED).

  19. Higher Harmonics Induced by Waves Propagating over A Submerged Obstacle in the Presence of Uniform Current

    Institute of Scientific and Technical Information of China (English)

    宁德志; 林红星; 滕斌; 邹青萍

    2014-01-01

    To investigate higher harmonics induced by a submerged obstacle in the presence of uniform current, a 2D fully nonlinear numerical wave flume (NWF) is developed by use of a time-domain higher-order boundary element method (HOBEM) based on potential flow theory. A four-point method is developed to decompose higher bound and free harmonic waves propagating upstream and downstream around the obstacle. The model predictions are in good agreement with the experimental data for free harmonics induced by a submerged horizontal cylinder in the absence of currents. This serves as a benchmark to reveal the current effects on higher harmonic waves. The peak value of non-dimensional second free harmonic amplitude is shifted upstream for the opposing current relative to that for zero current with the variation of current-free incident wave amplitude, and it is vice versa for the following current. The second-order analysis shows a resonant behavior which is related to the ratio of the cylinder diameter to the second bound mode wavelength over the cylinder. The second-order resonant position slightly downshifted for the opposing current and upshifted for the following current.

  20. A novel hybrid FEM-BEM method for 3D eddy current field calculation using current density J

    Institute of Scientific and Technical Information of China (English)

    LIU; Zhizhen(刘志珍); WANG; Yanzhang(王衍章); JIA; Zhiping(贾智平); SUN; Yingming(孙英明)

    2003-01-01

    This paper introduces a novel hybrid FEM-BEM method for calculating 3D eddy current field. In the eddy current region, the eddy current density J is solved by the finite element method (FEM) which is discretized by brick finite element mesh, while in the eddy current free region, the magnetic field intensity H is solved by the boundary element method (BEM) which is discretized by rectangular boundary element mesh. Under the boundary conditions, an algebraic equation group is obtained that only includes J by eliminating H. This method has many advantages over traditional ones, such as fewer variables, more convenient coupling between the FEM and the BEM and wider application to multiply-connected regions. The calculated values of two models are in good agreement with experimental results. This shows the validity of our method.

  1. LORETA current source density for duration mismatch negativity and neuropsychological assessment in early schizophrenia.

    Directory of Open Access Journals (Sweden)

    Tomohiro Miyanishi

    Full Text Available INTRODUCTION: Patients with schizophrenia elicit cognitive decline from the early phase of the illness. Mismatch negativity (MMN has been shown to be associated with cognitive function. We investigated the current source density of duration mismatch negativity (dMMN, by using low-resolution brain electromagnetic tomography (LORETA, and neuropsychological performance in subjects with early schizophrenia. METHODS: Data were obtained from 20 patients meeting DSM-IV criteria for schizophrenia or schizophreniform disorder, and 20 healthy control (HC subjects. An auditory odd-ball paradigm was used to measure dMMN. Neuropsychological performance was evaluated by the brief assessment of cognition in schizophrenia Japanese version (BACS-J. RESULTS: Patients showed smaller dMMN amplitudes than those in the HC subjects. LORETA current density for dMMN was significantly lower in patients compared to HC subjects, especially in the temporal lobes. dMMN current density in the frontal lobe was positively correlated with working memory performance in patients. CONCLUSIONS: This is the first study to identify brain regions showing smaller dMMN current density in early schizophrenia. Further, poor working memory was associated with decreased dMMN current density in patients. These results are likely to help understand the neural basis for cognitive impairment of schizophrenia.

  2. Induced fermionic charge and current densities in two-dimensional rings

    CERN Document Server

    Bellucci, S; Grigoryan, A Kh

    2016-01-01

    For a massive quantum fermionic field, we investigate the vacuum expectation values (VEVs) of the charge and current densities induced by an external magnetic flux in a two-dimensional circular ring. Both the irreducible representations of the Clifford algebra are considered. On the ring edges the bag (infinite mass) boundary conditions are imposed for the field operator. This leads to the Casimir type effect on the vacuum characteristics. The radial current vanishes. The charge and the azimuthal current are decomposed into the boundary-free and boundary-induced contributions. Both these contributions are odd periodic functions of the magnetic flux with the period equal to the flux quantum. An important feature that distinguishes the VEVs of the charge and current densities from the VEV of the energy density, is their finiteness on the ring edges. The current density is equal to the charge density for the outer edge and has the opposite sign on the inner edge. The VEVs are peaked near the inner edge and, as f...

  3. Effect of Applied Current Density on Morphological and Structural Properties of Electrodeposited Fe-Cu Films

    Institute of Scientific and Technical Information of China (English)

    Umut Sarac; M. Celalettin Baykul

    2012-01-01

    A detailed study has been carried out to investigate the effect of applied current density on the composition, crystallographic structure, grain size, and surface morphology of Fe-Cu films. X-ray diffraction (XRD) results show that the films consist of a mixture of face-centered cubic (fcc) Cu and body centered cubic (bcc) ~-Fe phases. The average crystalline size of both Fe and Cu particles decreases as the applied current density becomes more negative. Compositional analysis of Fe-Cu films indicates that the Fe content within the films increases with decreasing current density towards more negative values. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) have been used to investigate the surface morphology of Fe-Cu films. It is observed that the surface morphology of the films changes from dendritic structure to a cauliflower structure as the applied current density becomes more negative. The surface roughness and grain size of the Fe-Cu films decrease with decreasing applied current density towards more negative values.

  4. Higher Education in Kenya: An Assessment of Current Responses to the Imperative of Widening Access

    Science.gov (United States)

    Odhiambo, George

    2016-01-01

    Higher education is a key factor in a nation's effort to develop a highly skilled workforce for competing in the global economy. In this paper, current trends in accessibility, equity, participation and financing of higher education in Kenya are examined. The paper explores the challenges which need to be confronted and discusses the way forward…

  5. Propagation and deposition mechanisms of dense pyroclastic density currents: insights from analogue laboratory experiments. (Invited)

    Science.gov (United States)

    Roche, O.; Montserrat, S.; Niño, Y.; Tamburrino, A.

    2010-12-01

    Analogue laboratory experiments on air-particle flows represent a useful tool to investigate the mechanisms of propagation and deposition of dense (or the dense part of) pyroclastic density currents. In this context, we carried out experiments in the dam-break configuration and studied the emplacement processes of analogue biphasic currents generated from the quasi-instantaneous release of fluidized columns of fine (80 µm) particles. The low permeability of the granular material permitted relatively slow diffusion of the initial pore pressure within the flows until they came to halt. Analysis of the flow kinematics and comparison with flows of water in the same apparatus revealed that the air-particle currents propagated in two distinct stages. They behaved as their inertial water counterparts for most their emplacement, as both types of flows had the same morphology and propagated at constant front velocity U~√(2gh), h being the initial height of the granular column. This occurred as long as the height of the collapsing fluidized columns was higher than the that of the resultant flows, thus generating a driving pressure gradient. This fluid-inertial behavior suggested that the pore fluid pressure was high during propagation of the mixture. In order to check this hypothesis, we carried out non invasive measurements of the pore fluid pressure at the base of the air-particle flows and made correlation of the pressure signal with the flow structure from analyses of high speed videos. The flow structure consisted of a sliding head that caused underpressure relative to ambient conditions and whose magnitude correlated with the flow velocity. The flow head was followed by a body that generated overpressure and at the base of which a deposit aggraded at a nearly constant rate. Both the flow head and body were sheared pervasively as the internal velocity increased upwards. The combination of pressure advection from the source and relatively slow pressure diffusion

  6. Towards the definition of AMS facies in the deposits of pyroclastic density currents

    Science.gov (United States)

    Ort, M.H.; Newkirk, T.T.; Vilas, J.F.; Vazquez, J.A.; Ort, M.H.; Porreca, Massimiliano; Geissman, J.W.

    2014-01-01

    Anisotropy of magnetic susceptibility (AMS) provides a statistically robust technique to characterize the fabrics of deposits of pyroclastic density currents (PDCs). AMS fabrics in two types of pyroclastic deposits (small-volume phreatomagmatic currents in the Hopi Buttes volcanic field, Arizona, USA, and large-volume caldera-forming currents, Caviahue Caldera, Neuquén, Argentina) show similar patterns. Near the vent and in areas of high topographical roughness, AMS depositional fabrics are poorly grouped, with weak lineations and foliations. In a densely welded proximal ignimbrite, this fabric is overprinted by a foliation formed as the rock compacted and deformed. Medial deposits have moderate–strong AMS lineations and foliations. The most distal deposits have strong foliations but weak lineations. Based on these facies and existing models for pyroclastic density currents, deposition in the medial areas occurs from the strongly sheared, high-particle-concentration base of a density-stratified current. In proximal areas and where topography mixes this denser base upwards into the current, deposition occurs rapidly from a current with little uniformity to the shear, in which particles fall and collide in a chaotic fashion. Distal deposits are emplaced by a slowing or stalled current so that the dominant particle motion is vertical, leading to weak lineation and strong foliation.

  7. Effects of discharge current and voltage on the high density of metastable helium atoms

    Institute of Scientific and Technical Information of China (English)

    FengXian-Ping; DAndruczyk; BWJames; KTakiyama; SNamba; TOda

    2003-01-01

    Both hollow-cathode and Penning-type discharges were adopted toexcite helium atoms to a metastable state. Experimental data indicate that Penning discharge is more suitable for generating high fractions of metastables in a low-density helium hean for laser-induced fluorescence technique in measuring electric fields at the edge of a plasma. The metastable density increases with increasing helium gas pressure in the range of 1.33×10-2-66.7Pa. The highest metastable density of 3.8×1016m-3 is observed at a static gas pressure of 66.7Pa. An approximately linear relationship between the density of metastable helium atoms and the plasma discharge current is observed. Magnetic field plays a very important role in producing a high density of metastable atoms in Penning discharge.

  8. Effects of discharge current and voltage on the high density of metastable helium atoms

    Institute of Scientific and Technical Information of China (English)

    Feng Xian-Ping(冯贤平); D Andruczyk; B W James; K Takiyama; S Namba; T Oda

    2003-01-01

    Both hollow-cathode and Penning-type discharges were adopted to excite helium atoms to a metastable state.Experimental data indicate that Penning discharge is more suitable for generating high fractions of metastables in a low-density helium beam for laser-induced fluorescence technique in measuring electric fields at the edge of a plasma.The metastable density increases with increasing helium gas pressure in the range of 1.33× 10-2-66.7Pa. The highest metastable density of 3.8 × 1016m-3 is observed at a static gas pressure of 66.7Pa. An approximately linear relationship between the density of metastable helium atoms and the plasma discharge current is observed. Magnetic field plays a very important role in producing a high density of metastable atoms in Penning discharge.

  9. Effects of Current Density on Microstructure of Titania Coatings by Micro-arc Oxidation

    Institute of Scientific and Technical Information of China (English)

    Yue Yang; Hua Wu

    2012-01-01

    In the present study, titania coatings were prepared under different current density conditions in micro-arc oxidation (MAO) process on titanium alloy in NaAlO2 solution. The aim of this work was to study the effects of current density on the microstructure of titania coatings. The morphology and phase composition of the coatings were investigated by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD) and Raman spectra. The thickness and surface roughness of the coatings were characterized by confocal laser Scanning Microscopy (CLSM). The results showed that the coatings were composed of crystalline anatase and rutile phases of TiO2, and contain a network of evenly distributed small pores. It has also shown that an increase in current density leads to an increase in rutile content.

  10. Microstructure characterisation of solid oxide electrolysis cells operated at high current density

    DEFF Research Database (Denmark)

    Bowen, Jacob R.; Bentzen, Janet Jonna; Chen, Ming;

    High temperature solid oxide cells can be operated either as fuel cells or electrolysis cells for efficient power generation or production of hydrogen from steam or synthesis gas (H2 + CO) from steam and CO2 respectively. When operated under harsh conditions, they often exhibit microstructural......, microstructure evolution of the Ni-yttria stabilized zirconia (YSZ) is followed as a function of galvanostatic steam electrolysis testing at current densities between -0.5 and -1.0 A cm-2 for periods of up to 750 hours at 800 °C. The volume fraction and size of the percolating Ni particles was statistically...... quantified using the mean linear intercept method as a function of current density and correlated to increases in serial resistance. The above structural changes are then compared in terms of electrode degradation observed during the co-electrolysis of steam and CO2 at current densities up to -1.5 A cm-2...

  11. Higher Spin Currents in the N=2 Stringy Coset Minimal Model

    CERN Document Server

    Ahn, Changhyun

    2016-01-01

    In the coset model based on (A_{N-1}^{(1)} \\oplus A_{N-1}^{(1)}, A_{N-1}^{(1)}) at level (N, N; 2N), it is known that the N=2 superconformal algebra can be realized by the two kinds of adjoint fermions. Each Kac-Moody current of spin-1 is given by the product of fermions with structure constant (f symbols) as usual. One can construct the spin-1 current by combining the above two fermions with the structure constant and the spin-1 current by multiplying these two fermions with completely symmetric SU(N) invariant tensor of rank 3 (d symbols). The lowest higher spin-2 current with nonzero U(1) charge (corresponding to the zeromode eigenvalue of spin-1 current of N=2 superconformal algebra) can be obtained from these four spin-1 currents in quadratic form. Similarly, the other type of lowest higher spin-2 current, whose U(1) charge is opposite to the above one, can be obtained also. Four higher spin-5/2 currents can be constructed from the operator product expansions (OPEs) between the spin-3/2 currents of N=2 s...

  12. SOL plasma measurements during high density and long duration current drive on TRIAM-1M

    Energy Technology Data Exchange (ETDEWEB)

    Takemura, Takeharu; Kawasaki, Shoji; Jotaki, Eriko; Makino, Ken-ichi; Sakamoto, Mizuki; Nakamura, Kazuo; Nakamura, Yukio; Itoh, Sanae; Itoh, Satoshi [Kyushu Univ., Kasuga, Fukuoka (Japan). Research Inst. for Applied Mechanics

    1997-02-01

    In the superconducting, strong magnetic field tokamak, TRIAM-1M, for the purpose of maintaining high density plasma for long time, the current drive experiment using 8.2 GHz lower hybrid wave has been carried out. For maintaining high density plasma for long time, it is indispensable to control gas puff and recycling from wall, as these are closely related to the structure and characteristics of boundary plasma including scrape-off layer (SOL). In this study, in the high density, long time current drive using 8.2 GHz lower hybrid wave, the electron density and electron temperature of SOL plasma were measured by using double probe, and the z-direction distribution and the toroidal magnetic field dependence of the electron density and electron temperature of SOL plasma were examined and compared with OH discharge. Also the dependence of the electron density of SOL plasma on the phase difference in a adjoining waveguide tubes was examined. The experimental setup and the double probe theory are explained. The experimental results of the change with time lapse, the z-direction distribution and the magnetic field dependence of the electron density and electron temperature of SOL plasma are reported. (K.I.)

  13. The importance of current contributions to shielding constants in density-functional theory.

    Science.gov (United States)

    Reimann, Sarah; Ekström, Ulf; Stopkowicz, Stella; Teale, Andrew M; Borgoo, Alex; Helgaker, Trygve

    2015-07-28

    The sources of error in the calculation of nuclear-magnetic-resonance shielding constants determined by density-functional theory are examined. Highly accurate Kohn-Sham wave functions are obtained from coupled-cluster electron density functions and used to define accurate-but current independent-density-functional shielding constants. These new reference values, in tandem with high-accuracy coupled-cluster shielding constants, provide a benchmark for the assessment of errors in common density-functional approximations. In particular the role of errors arising in the diamagnetic and paramagnetic terms is investigated, with particular emphasis on the role of current-dependence in the latter. For carbon and nitrogen the current correction is found to be, in some cases, larger than 10 ppm. This indicates that the absence of this correction in general purpose exchange-correlation functionals is one of the main sources of error in shielding calculations using density functional theory. It is shown that the current correction improves the shielding performance of many popular approximate DFT functionals.

  14. Ion Current Density Calculation of the Inductive Radio Frequency Ion Source

    Directory of Open Access Journals (Sweden)

    V.I. Voznyi

    2012-10-01

    Full Text Available A radio-frequency (RF inductive ion source at 27.12 MHz is investigated. With a global model of the argon discharge, plasma density, electron temperature and ion current density of the ion source is calculated in relation to absorbed RF power and gas pressure as a discharge chamber size changes. It is found that ion beam current density grows as the discharge chamber size decreases. Calculations show that in the RF source with a discharge chamber 30 mm in diameter and 35 mm long the ion current density is 40 mA/cm2 at 100 W of absorbed RF power and 7 mTorr of pressure, and agrees well with experimentally measured value of 43 mA/cm2. With decreasing discharge chamber diameter to 15 mm ion current density can reach 85 mA/cm2 at absorbed RF power of 100 W.

  15. Lower-energy-density diets are associated with higher monetary costs per kilocalorie and are consumed by women of higher socioeconomic status.

    Science.gov (United States)

    Monsivais, Pablo; Drewnowski, Adam

    2009-05-01

    Diets of lower energy density are associated with higher diet quality, lower body weights, and better health outcomes. This study examined associations among dietary energy density, energy-adjusted diet costs, and socioeconomic indicators of study participants. In this cross-sectional study, energy and nutrient intakes for 164 men and women aged 25 to 65 years were obtained using a food frequency instrument between June 2005 and September 2006. Dietary energy density (kcal/g) was calculated with and without beverages. Energy-adjusted diet costs ($/2,000 kcal) were calculated using food prices in Seattle, WA. Tertile splits of energy density and energy cost were analyzed using tests for linear trend. Linear regression models tested the association between education, income, and dietary variables, adjusting for age and sex. Diets of lower energy density were associated with higher absolute nutrient intakes. Diets of lower energy density were also associated with higher energy-adjusted diet costs. Conversely, highest energy density diets were associated with lower intakes of micronutrients and fiber and lower costs. Education and household income showed a negative association with dietary energy density in regression models. Education and household incomes showed a positive association with the energy-adjusted cost of the diet. Education was a stronger predictor of both energy density and energy cost than was household income. Higher-quality diets were not only more costly per kilocalorie but were also consumed by persons of higher educational level. The influence of diet quality on health, observed in some epidemiologic studies, might be modulated by unobserved indexes of socioeconomic status.

  16. Lower-energy-density diets are associated with higher monetary costs per kilocalorie and are consumed by women of higher socioeconomic status2

    Science.gov (United States)

    Monsivais, Pablo; Drewnowski, Adam

    2010-01-01

    Objective Diets of lower energy density are associated with higher diet quality, lower body weights, and better health outcomes. This study examined the association between dietary energy density, energy-adjusted diet costs and socioeconomic indicators of study participants. Design In this cross-sectional study, energy and nutrient intakes for 164 men and women aged 25–65y were obtained using a food frequency instrument between June 2005 and September 2006. Dietary energy density (kcal/g) was calculated with and without beverages. Energy-adjusted diet costs ($/2,000 kcal) were calculated using food prices in Seattle. Tertile splits of energy density and energy cost were analyzed using tests for linear trend. Linear regression models tested the association between gender, education, income and dietary variables, adjusting for age. Results Diets of lower energy density were associated with higher absolute nutrient intakes. Diets of lower energy density were also associated with higher energy-adjusted diet costs. Conversely, highest energy density diets were associated with lower intakes of micronutrients and fiber and lower costs. Education and household income showed a negative association with dietary energy density in regression models. Education and household incomes showed a positive association with the energy-adjusted cost of the diet and education was a stronger predictor of both energy density and energy cost than was household income. Conclusion Higher-quality diets were not only more costly per kcal but were also consumed by persons of higher educational level. The impact of diet quality on health, observed in some epidemiologic studies, might be modulated by unobserved indices of socioeconomic status. PMID:19394467

  17. Corrosion current density prediction in reinforced concrete by imperialist competitive algorithm.

    Science.gov (United States)

    Sadowski, Lukasz; Nikoo, Mehdi

    2014-01-01

    This study attempted to predict corrosion current density in concrete using artificial neural networks (ANN) combined with imperialist competitive algorithm (ICA) used to optimize weights of ANN. For that reason, temperature, AC resistivity over the steel bar, AC resistivity remote from the steel bar, and the DC resistivity over the steel bar are considered as input parameters and corrosion current density as output parameter. The ICA-ANN model has been compared with the genetic algorithm to evaluate its accuracy in three phases of training, testing, and prediction. The results showed that the ICA-ANN model enjoys more ability, flexibility, and accuracy.

  18. Limitations of absolute current densities derived from the Semel & Skumanich method

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Semel and Skumanich proposed a method to obtain the absolute electric current density, |Jz|, without disambiguation of 180° in the transverse field directions. The advantage of the method is that the uncertainty in the determination of the ambiguity in the magnetic azimuth is removed. Here, we investigate the limits of the calculation when applied to a numerical MHD model. We have found that the combination of changes in the magnetic azimuth with vanishing horizontal field component leads to errors, where electric current densities are often strong. Where errors occur, the calculation gives |Jz| too small by factors typically 1.2 - 2.0.

  19. Yerba Mate (Ilex paraguariensis) consumption is associated with higher bone mineral density in postmenopausal women.

    Science.gov (United States)

    Conforti, Andrea S; Gallo, María E; Saraví, Fernando D

    2012-01-01

    Yerba Mate (Ilex paraguariensis) tea consumption is higher in Argentina and other South American countries than those of coffee or tea (Camellia sinensis). The effects of Yerba Mate on bone health have not previously been explored. From a program for osteoporosis prevention and treatment, postmenopausal women who drank at least 1 L of Yerba Mate tea daily during 4 or more years (n=146) were identified, and matched by age and time since menopause with an equal number of women who did not drink Yerba Mate tea. Their bone mineral density (BMD) was measured by dual-energy X-ray absorptiometry (DXA) at the lumbar spine and femoral neck. Yerba Mate drinkers had a 9.7% higher lumbar spine BMD (0.952 g/cm(2) versus 0.858 g/cm(2): p<0.0001) and a 6.2% higher femoral neck BMD (0.817 g/cm(2) versus 0.776 g/cm(2); p=0.0002). In multiple regression analysis, Yerba Mate drinking was the only factor, other than body mass index, which showed a positive correlation with BMD at both the lumbar spine (p<0.0001) and the femoral neck (p=0.0028). Results suggest a protective effect of chronic Yerba Mate consumption on bone.

  20. Modelling of Current Density Redistribution in Hollow Needle to Plate Electrical Discharge Designed for Ozone Generation

    Science.gov (United States)

    Kriha, Vitezslav

    2003-10-01

    Non-thermal plasma of atmospheric pressure electrical discharges in flowing air can be used to generation of ozone. We have been observed two modes of discharge burning in a hollow needle to plane electrodes configuration studied in the ozone generation experiments: A low current diffuse mode is characterized by increasing of the ozone production with the discharge current; a high current filamentary mode is disadvantageous for the ozone generation(the ozone production decreases when the discharge current increases). A possible interpretation of this effect is following: The filamentary mode discharge current density is redistributed and high current densities in filaments cores lead to degradation of the ozone generation. Local fields in the discharge can be modified by charged metallic and/or dielectric components (passive modulators) in the discharge space. An interactive numerical model has been developed for this purpose. This model is based on Ferguson's polynomial objects for both the discharge chamber scene modelling and the discharge fields analyzing. This approach allows intuitive modifications of modulators shapes and positions in 3D scene followed by quantitative comparison of the current density distribution with previous configurations.

  1. The electrical current density vector in the inner penumbra of a Sunspot

    CERN Document Server

    Puschmann, K G; Pillet, V Martínez

    2010-01-01

    We determine the entire electrical current density vector in a geometrical 3D volume of the inner penumbra of a sunspot from an inversion of spectropolarimetric data obtained with Hinode/SP. Significant currents are seen to wrap around the hotter, more elevated regions with lower and more horizontal magnetic field that harbor strong upflows and radial outflows (the intraspines). The horizontal component of the current density vector is 3-4 times larger than the vertical; nearly all previous studies only obtain the vertical component and thus strongly underestimate the current density. The current density and the magnetic field vectors form an angle of about 20 degrees. The plasma beta at the 0 km level is larger than 1 in the intraspines and is one order of magnitude lower in the background component of the penumbra (spines). At the 200 km level, the plasma beta is below 0.3 nearly everywhere. The plasma beta surface as well as the surface optical depth unity are very corrugated. At the borders of intraspines...

  2. Large Eddy Simulations of Compositional Density Currents Flowing Over a Mobile Bed

    Science.gov (United States)

    Kyrousi, Foteini; Zordan, Jessica; Leonardi, Alessandro; Juez, Carmelo; Zanello, Francesca; Armenio, Vincenzo; Franca, Mário J.

    2017-04-01

    Density currents are a ubiquitous phenomenon caused by natural events or anthropogenic activities, and play an important role in the global sediment cycle; they are agents of long distance sediment transport in lakes, seas and oceans. Density gradients induced by salinity, temperature differences, or by the presence of suspended material are all possible triggers of a current. Such flows can travel long distances while eroding or depositing bed materials. This can provoke rapid topological changes, which makes the estimation of their transport capacity of prime interest for environmental engineering. Despite their relevance, field data regarding their dynamics is limited due to density currents scattered and unpredictable occurrence in nature. For this reason, laboratory experiments and numerical simulations have been a preferred way to investigate sediment transport processes associated to density currents. The study of entrainment and deposition processes requires detailed data of velocities spatial and temporal distributions in the boundary layer and bed shear stress, which are troublesome to obtain in laboratory. Motivated by this, we present 3D wall-resolved Large Eddy Simulations (LES) of density currents generated by lock-exchange. The currents travel over a smooth flat bed, which includes a section composed by erodible fine sediment susceptible of eroding. Several sediment sizes and initial density gradients are considered. The grid is set to resolve the velocity field within the boundary layer of the current (a tiny fraction of the total height), which in turn allows to obtain predictions of the bed shear stress. The numerical outcomes are compared with experimental data obtained with an analogous laboratory setting. In laboratory experiments salinity was chosen for generating the initial density gradient in order to facilitate the identification of entrained particles, since salt does not hinder the possibility to track suspended particles. Under these

  3. Simulations and experiments of intense ion beam current density compression in space and timea)

    Science.gov (United States)

    Sefkow, A. B.; Davidson, R. C.; Gilson, E. P.; Kaganovich, I. D.; Anders, A.; Coleman, J. E.; Leitner, M.; Lidia, S. M.; Roy, P. K.; Seidl, P. A.; Waldron, W. L.; Yu, S. S.; Welch, D. R.

    2009-05-01

    The Heavy Ion Fusion Science Virtual National Laboratory has achieved 60-fold longitudinal pulse compression of ion beams on the Neutralized Drift Compression Experiment (NDCX) [P. K. Roy et al., Phys. Rev. Lett. 95, 234801 (2005)]. To focus a space-charge-dominated charge bunch to sufficiently high intensities for ion-beam-heated warm dense matter and inertial fusion energy studies, simultaneous transverse and longitudinal compression to a coincident focal plane is required. Optimizing the compression under the appropriate constraints can deliver higher intensity per unit length of accelerator to the target, thereby facilitating the creation of more compact and cost-effective ion beam drivers. The experiments utilized a drift region filled with high-density plasma in order to neutralize the space charge and current of an ˜300 keV K+ beam and have separately achieved transverse and longitudinal focusing to a radius 2 MeV) ion beam user-facility for warm dense matter and inertial fusion energy-relevant target physics experiments.

  4. Surface layer structure and average contact temperature of copper-containing materials under dry sliding with high electric current density

    Science.gov (United States)

    Fadin, V. V.; Aleutdinova, M. I.; Rubtsov, V. Ye.; Aleutdinov, K. A.

    2016-11-01

    Dry sliding of copper and powder composites of Cu-Fe and Cu-Fe-graphite compositions against 1045 steel under electric current of contact density higher than 250 A/cm2 has been studied, which demonstrated the change in surface layer structure and formation of tribolayer consisting of iron, copper and FeO oxide. Signs of quasi-viscous flow of worn surface were observed. It was noted that the thin contact layer containing about 40 at % of oxygen and 40% of Fe was the main factor decreasing the adhesion interaction. It was affirmed that the introduction of graphite into the primary structure of the composite leads to rather low content of FeO oxide and to the increased tendency of surface layer to catastrophic deterioration under sliding with contact current density of about 300 A/cm2. The temperature of contact did not exceed 400°C.

  5. Effect of current density on distribution coefficient of solute at solid-liquid interface

    Institute of Scientific and Technical Information of China (English)

    常国威; 王自东; 吴春京; 胡汉起

    2003-01-01

    When current passes through the solid-liquid interface, the growth rate of crystal, solid-liquid interfaceenergy and radius of curvature at dendritic tip will change. Based on this fact, the theoretical relation between thedistribution of solute at solid-liquid interface and current density was established, and the effect of current on thedistribution coefficient of solute through effecting the rate of crystal growth, the solid-liquid interface energy and theradius of curvature at the dendritic tip was discussed. The results show that as the current density increases, thedistribution coefficient of solute tends to rise in a whole, and when the former is larger than about 400 A/cm2 , thelatter varies significantly.

  6. [Heart current density as the most important biological parameter of electrocution in the bathtub].

    Science.gov (United States)

    Fechner, G; Brinkmann, B; Heckmann, M

    1990-01-01

    The most important factor during electrocution in a bathtub is the amount of current flowing through a body, not the amount of voltage. A method of measurement is introduced which--under simulation of various electrical situations--provides the possibility to measure the current flowing through the heart and to determine it's direction and density in the tissue. Hereby a ranking of the different factors influencing electrocution can be set up.

  7. Dependence of critical current density on crystalline direction in thin YBCO films

    DEFF Research Database (Denmark)

    Paturi, P.; Peurla, M.; Raittila, J.

    2005-01-01

    The dependence of critical current density (J(c)) on the angle between the current direction and the (100) direction in the ab-plane of thin YBCO films deposited on (001)-SrTiO3 from natiocrystalline and microcrystalline targets is studied using magneto-optical microscopy. In the films made from ...... indicating that in addition to linear defects also the twin boundaries are very important flux pinning sites. (c) 2005 Elsevier B.V. All rights reserved....

  8. A mathematical model of the current density distribution in electrochemical cells - AUTHORS’ REVIEW

    Directory of Open Access Journals (Sweden)

    PREDRAG M. ŽIVKOVIĆ

    2011-06-01

    Full Text Available An approach based on the equations of electrochemical kinetics for the estimation of the current density distribution in electrochemical cells is presented. This approach was employed for a theoretical explanation of the phenomena of the edge and corner effects. The effects of the geometry of the system, the kinetic parameters of the cathode reactions and the resistivity of the solution are also discussed. A procedure for a complete analysis of the current distribution in electrochemical cells is presented.

  9. Higher-order adaptive finite-element methods for Kohn–Sham density functional theory

    Energy Technology Data Exchange (ETDEWEB)

    Motamarri, P. [Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Nowak, M.R. [Department of Electrical Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Leiter, K.; Knap, J. [U.S. Army Research Labs, Aberdeen Proving Ground, Aberdeen, MD 21001 (United States); Gavini, V., E-mail: vikramg@umich.edu [Department of Mechanical Engineering, University of Michigan, Ann Arbor, MI 48109 (United States)

    2013-11-15

    We present an efficient computational approach to perform real-space electronic structure calculations using an adaptive higher-order finite-element discretization of Kohn–Sham density-functional theory (DFT). To this end, we develop an a priori mesh-adaption technique to construct a close to optimal finite-element discretization of the problem. We further propose an efficient solution strategy for solving the discrete eigenvalue problem by using spectral finite-elements in conjunction with Gauss–Lobatto quadrature, and a Chebyshev acceleration technique for computing the occupied eigenspace. The proposed approach has been observed to provide a staggering 100–200-fold computational advantage over the solution of a generalized eigenvalue problem. Using the proposed solution procedure, we investigate the computational efficiency afforded by higher-order finite-element discretizations of the Kohn–Sham DFT problem. Our studies suggest that staggering computational savings—of the order of 1000-fold—relative to linear finite-elements can be realized, for both all-electron and local pseudopotential calculations, by using higher-order finite-element discretizations. On all the benchmark systems studied, we observe diminishing returns in computational savings beyond the sixth-order for accuracies commensurate with chemical accuracy, suggesting that the hexic spectral-element may be an optimal choice for the finite-element discretization of the Kohn–Sham DFT problem. A comparative study of the computational efficiency of the proposed higher-order finite-element discretizations suggests that the performance of finite-element basis is competing with the plane-wave discretization for non-periodic local pseudopotential calculations, and compares to the Gaussian basis for all-electron calculations to within an order of magnitude. Further, we demonstrate the capability of the proposed approach to compute the electronic structure of a metallic system containing 1688

  10. Effect of electrolysis parameters on the morphologies of copper powder obtained at high current densities

    Directory of Open Access Journals (Sweden)

    Orhan Gökhan

    2012-01-01

    Full Text Available The effects of copper ion concentrations and electrolyte temperature on the morphologies and on the apparent densities of electrolytic copper powders at high current densities under galvanostatic regime were examined. These parameters were evaluated by the current efficiency of hydrogen evolution. In addition, scanning electron microscopy was used for analyzing the morphology of the copper powders. It was found that the morphology was dependent over the copper ion concentration and electrolyte temperature under same current density (CD conditions. At 150 mA cm-2 and the potential of 1000±20 mV (vs. SCE, porous and disperse copper powders were obtained at low concentrations of Cu ions (0.120 M Cu2+ in 0.50 M H2SO4. Under this condition, high rate of hydrogen evolution reaction took place parallel to copper electrodeposition. The morphology was changed from porous, disperse and cauliflower-like to coral-like, shrub-like and stalk-stock like morphology with the increasing of Cu ion concentrations towards 0.120 M, 0.155 M, 0.315 M, 0.475 M and 0.630 M Cu2+ in 0.5 M H2SO4 respectively at the same CD. Similarly, as the temperature was increased, powder morphology and apparent density were observed to be changed. The apparent density values of copper powders were found to be suitable for many of the powder metallurgy applications.

  11. Down-regulation of endogenous KLHL1 decreases voltage-gated calcium current density.

    Science.gov (United States)

    Perissinotti, Paula P; Ethington, Elizabeth G; Cribbs, Leanne; Koob, Michael D; Martin, Jody; Piedras-Rentería, Erika S

    2014-05-01

    The actin-binding protein Kelch-like 1 (KLHL1) can modulate voltage-gated calcium channels in vitro. KLHL1 interacts with actin and with the pore-forming subunits of Cav2.1 and CaV3.2 calcium channels, resulting in up-regulation of P/Q and T-type current density. Here we tested whether endogenous KLHL1 modulates voltage gated calcium currents in cultured hippocampal neurons by down-regulating the expression of KLHL1 via adenoviral delivery of shRNA targeted against KLHL1 (shKLHL1). Control adenoviruses did not affect any of the neuronal properties measured, yet down-regulation of KLHL1 resulted in HVA current densities ~68% smaller and LVA current densities 44% smaller than uninfected controls, with a concomitant reduction in α(1A) and α(1H) protein levels. Biophysical analysis and western blot experiments suggest Ca(V)3.1 and 3.3 currents are also present in shKLHL1-infected neurons. Synapsin I levels, miniature postsynaptic current frequency, and excitatory and inhibitory synapse number were reduced in KLHL1 knockdown. This study corroborates the physiological role of KLHL1 as a calcium channel modulator and demonstrates a novel, presynaptic role.

  12. Interpretation of very low frequency electromagnetic measurements in terms of normalized current density over variable topography

    Science.gov (United States)

    Singh, Anand; Sharma, S. P.

    2016-10-01

    A 2D inversion approach is developed to interpret VLF electromagnetic measurement recorded over variable topography. To depict the variable topography accurately, an octree mesh discretization is incorporated. Subsurface structure is modeled in terms of apparent current density distribution and compared with the inversion results for actual resistivity distribution obtained using numerical techniques. The study demonstrates that the results obtained using both approaches (current density and resistivity distribution) are comparable, but due to analytical expression, current density imaging is faster. The conjugate gradient method is used to reduce the computation time and storage space when solving the matrix equations, resulting in feasible and practical imaging inversion of VLF data. The preconditioned matrix, which is determined by the distances between the blocks and observation points, has an important function in improving the resolution. In case of flat earth, preconditioned conjugate gradient inversion of data results in images that are comparable to those obtained using resistivity inversion. We also test whether topography variation in the order of skin depth is significant to incorporate topography in the modeling. The example of a topographical field VLF data inversion shows the efficacy of the presented approach to appraise the subsurface structure in terms of current density.

  13. Time-dependent current-density-functional theory for the metallic response of solids

    NARCIS (Netherlands)

    Romaniello, P; de Boeij, PL

    2005-01-01

    We extend the formulation of time-dependent current-density-functional theory for the linear response properties of dielectric and semi-metallic solids [Kootstra , J. Chem. Phys. 112, 6517 (2000)] to treat metals as well. To achieve this, the Kohn-Sham response functions have to include both interba

  14. Time-dependent current-density-functional theory for the metallic response of solids

    NARCIS (Netherlands)

    Romaniello, P; de Boeij, PL

    We extend the formulation of time-dependent current-density-functional theory for the linear response properties of dielectric and semi-metallic solids [Kootstra , J. Chem. Phys. 112, 6517 (2000)] to treat metals as well. To achieve this, the Kohn-Sham response functions have to include both

  15. The Keldysh formalism applied to time-dependent current-density-functional theory

    NARCIS (Netherlands)

    Gidopoulos, NI; Wilson, S

    2003-01-01

    In this work we demonstrate how to derive the Kohn-Sham equations of time-dependent current-density functional theory from a generating action functional defined on a Keldysh time contour. These Kohn-Sham equations contain an exchange-correlation contribution to the vector potential. For this

  16. Reliability of quantitative EEG (qEEG) measures and LORETA current source density at 30 days.

    Science.gov (United States)

    Cannon, Rex L; Baldwin, Debora R; Shaw, Tiffany L; Diloreto, Dominic J; Phillips, Sherman M; Scruggs, Annie M; Riehl, Timothy C

    2012-06-14

    There is a growing interest for using quantitative EEG and LORETA current source density in clinical and research settings. Importantly, if these indices are to be employed in clinical settings then the reliability of these measures is of great concern. Neuroguide (Applied Neurosciences) is sophisticated software developed for the analyses of power, and connectivity measures of the EEG as well as LORETA current source density. To date there are relatively few data evaluating topographical EEG reliability contrasts for all 19 channels and no studies have evaluated reliability for LORETA calculations. We obtained 4 min eyes-closed and eyes-opened EEG recordings at 30-day intervals. The EEG was analyzed in Neuroguide and FFT power, coherence and phase was computed for traditional frequency bands (delta, theta, alpha and beta) and LORETA current source density was calculated in 1 Hz increments and summed for total power in eight regions of interest (ROI). In order to obtain a robust measure of reliability we utilized a random effects model with an absolute agreement definition. The results show very good reproducibility for total absolute power and coherence. Phase shows lower reliability coefficients. LORETA current source density shows very good reliability with an average 0.81 for ECB and 0.82 for EOB. Similarly, the eight regions of interest show good to very good agreement across time. Implications for future directions and use of qEEG and LORETA in clinical populations are discussed.

  17. Advanced Tokamak current density profiles for non-inductive Tore Supra operation

    Energy Technology Data Exchange (ETDEWEB)

    Kazarian-Vibert, F.; Litaudon, X.; Arslanbekov, R.; Bibet, P.; Froissard, P.; Goniche, M.; Hoang, G.T.; Joffrin, E.; Moreau, D.; Peysson, Y.; Rey, G. [Association Euratom-CEA, Centre d`Etudes de Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. de Recherches sur la Fusion Controlee

    1995-12-31

    This document deals with the advanced Tokamak concept concerning self consistent hollow current density profiles. Several Lower Hybrid experiments performed on Tore Supra are presented: the feasibility of the constant-flux operation mode is demonstrated and a new improved confinement regime with a reversed shear has been obtained. (TEC). 12 refs., 5 figs.

  18. Degradation of Solid Oxide Electrolysis Cells Operated at High Current Densities

    DEFF Research Database (Denmark)

    Tao, Youkun; Ebbesen, Sune Dalgaard; Mogensen, Mogens Bjerg

    2014-01-01

    In this work the durability of solid oxide cells for co-electrolysis of steam and carbon dioxide (45 % H2O + 45 % CO2 + 10 % H2) at high current densities was investigated. The tested cells are Ni-YSZ electrode supported, with a YSZ electrolyte and either a LSM-YSZ or LSCF-CGO oxygen electrode...

  19. Behaviour of bipolar membranes at high current density. Water diffusion limitation

    NARCIS (Netherlands)

    Krol, J.J.; Jansink, M.G.J.; Wessling, Matthias; Strathmann, H.

    1998-01-01

    In this paper the behaviour of bipolar membranes at very high current density is discussed. Current–voltage curves are determined, both for the Tokuyama Soda BP-1 and the WSI Technologies bipolar membrane. The current–voltage curves are characterised by an inflection point at which a drastic

  20. High current density in light-emitting transistors of organic single crystals

    NARCIS (Netherlands)

    Takenobu, Taishi; Bisri, Satria Zulkarnaen; Takahashi, Tetsuo; Yahiro, Masayuki; Adachi, Chihaya; Iwasa, Yoshihiro

    2008-01-01

    We measured the external electroluminescence quantum efficiency (eta(ext)) in light-emitting field-effect transistors (LETs) made of organic single crystals and found that, in the ambipolar transport region, eta(ext) is not degraded up to several hundreds A/cm(2) current-density range, which is 2 or

  1. Particle image velocimetry measurements and numerical modeling of a saline density current

    CSIR Research Space (South Africa)

    Gerber, G

    2011-03-01

    Full Text Available Particle image velocimetry scalar measurements were carried out on the body of a stably stratified density current with an inlet Reynolds number of 2,300 and bulk Richardson number of 0.1. These measurements allowed the mass and momentum transport...

  2. Model Predictive Control with Integral Action for Current Density Profile Tracking in NSTX-U

    Science.gov (United States)

    Ilhan, Z. O.; Wehner, W. P.; Schuster, E.; Boyer, M. D.

    2016-10-01

    Active control of the toroidal current density profile may play a critical role in non-inductively sustained long-pulse, high-beta scenarios in a spherical torus (ST) configuration, which is among the missions of the NSTX-U facility. In this work, a previously developed physics-based control-oriented model is embedded in a feedback control scheme based on a model predictive control (MPC) strategy to track a desired current density profile evolution specified indirectly by a desired rotational transform profile. An integrator is embedded into the standard MPC formulation to reject various modeling uncertainties and external disturbances. Neutral beam powers, electron density, and total plasma current are used as actuators. The proposed MPC strategy incorporates various state and actuator constraints directly into the control design process by solving a constrained optimization problem in real-time to determine the optimal actuator requests. The effectiveness of the proposed controller in regulating the current density profile in NSTX-U is demonstrated in closed-loop nonlinear simulations. Supported by the US DOE under DE-AC02-09CH11466.

  3. Dissipative particle dynamics simulation for the density currents of polymer fluids

    Science.gov (United States)

    Li, Yanggui; Geng, Xingguo; Liu, Zhijun; Liu, Qingsheng; Ouyang, Jie

    2016-11-01

    In this work, the two-dimensional lock-exchange density currents of polymer fluids are numerically investigated using dissipative particle dynamics (DPD) at the mesoscale particle level. A modified finitely extensible nonlinear elastic (FENE) chain model is chosen to describe the polymer system, which perfectly depicts not only the elastic tension but also the elastic repulsion between the adjacent beads with bond length as the equilibrium length of one segment. Through the model and numerical simulation, we analyze the dynamics behavior of the density currents of polymer fluids. A comparison with its Newtonian counterpart suggests that the interface between two polymer fluids is more smoothed, and the front structure is different from the Newtonian case because the Kelvin-Helmholtz instability and cleft instability are suppressed by the polymer. Besides, we also probe the influences of polymer volume concentration, chain length and extensibility on the density currents. These simulation results show that increasing any of the parameters, concentration, chain length, and extensibility, the inhibiting effect of polymer on the density currents becomes more significant.

  4. Contributions for the modelling of submarine cables – current density and simplified modelling of wired layers

    DEFF Research Database (Denmark)

    Silva, Filipe Miguel Faria da; Bak, Claus Leth; Ebdrup, Thomas

    2015-01-01

    This article researches two topics relevant for the development of accurate formulae able to estimate the ampacity of HVAC submarine cables. Simplified formulae for estimating the current density distribution, which can be used for theoretical analyses, are developed and compared with the exact...

  5. Investigation of the Critical Current Density of YBaCuO high-temperature Superconductor Ceramic

    OpenAIRE

    METSKHVARISHVILI, I. R.; KEKELIDZE, N. P.; METSKHVARISHVILI, M. R.

    2002-01-01

    The method of high harmonics is used to investigate penetration of low magnetic fields within the Y1Ba2Cu3O7 high-temperature superconductor ceramic. Given experimental results are explained by the modal dependencies between the value of critical current density and the magnetic induction B: jc(B) = jc(0){\\frac{{B02}} {{B02 + B2}}}.

  6. Influence of electropolishing current densities on sulfur generation at niobium surface

    Energy Technology Data Exchange (ETDEWEB)

    Tyagi, P.V., E-mail: tyagipv@ornl.gov [The Graduate University for Advanced Studies, Tsukuba, Ibaraki (Japan); Nishiwaki, M.; Noguchi, T.; Sawabe, M.; Saeki, T.; Hayano, H.; Kato, S. [KEK, High Energy Accelerator Research Organization, Tsukuba, Ibaraki (Japan)

    2013-11-15

    We report the effect of different current densities on sulfur generation at Nb surface in the electropolishing (EP) with aged electrolyte. In this regard, we conducted a series of electropolishing (EP) experiments in aged EP electrolyte with high (≈50 mA/cm{sup 2}) and low (≈30 mA/cm{sup 2}) current densities on Nb surfaces. The experiments were carried out both for laboratory coupons and a real Nb single cell cavity with six witness samples located at three typical positions (equator, iris and beam pipe). Sample's surfaces were investigated by XPS (X-ray photoelectron spectroscopy), SEM (scanning electron microscope) and EDX (energy dispersive X-ray spectroscopy). The surface analysis showed that the EP with a high current density produced a huge amount of sulfate/sulfite particles at Nb surface whereas the EP with a low current density was very helpful to mitigate sulfate/sulfite at Nb surface in both the experiments.

  7. Electrical safety in spinal cord stimulation: current density analysis by computer modeling

    NARCIS (Netherlands)

    Wesselink, W.A.; Holsheimer, J.

    1995-01-01

    The possibility of tissue damage in spinal cord stimulation was investigated in a computer modeling study. A decrease of the electrode area in monopolar stimulation resulted in an increase of the current density at the electrode surface. When comparing the modeling results with experimental data

  8. The influence of critical current density of Bi-2212 superconductors by defects after Yb-doping

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Tianni [State key Laboratory for Mechanical Behavior of Materials of Xi' an Jiaotong University, Xi' an 710014 (China); SMRC, Northwest Institute for Nonferrous Metal Research, Xi' an 710016 (China); Zhang, Cuiping [SMRC, Northwest Institute for Nonferrous Metal Research, Xi' an 710016 (China); Guo, Shengwu [State key Laboratory for Mechanical Behavior of Materials of Xi' an Jiaotong University, Xi' an 710014 (China); Wu, Yifang [State key Laboratory for Mechanical Behavior of Materials of Xi' an Jiaotong University, Xi' an 710014 (China); SMRC, Northwest Institute for Nonferrous Metal Research, Xi' an 710016 (China); Li, Chengshan, E-mail: csli368@126.com [SMRC, Northwest Institute for Nonferrous Metal Research, Xi' an 710016 (China); Zhou, Lian [State key Laboratory for Mechanical Behavior of Materials of Xi' an Jiaotong University, Xi' an 710014 (China); SMRC, Northwest Institute for Nonferrous Metal Research, Xi' an 710016 (China)

    2015-12-15

    Highlights: • Ca substituting Yb element in Bi-2212 single crystal. • The critical current density of this sample is the highest without the optimal Tc value. • The Cu–O{sub 2} and Ca–O layers in pure and doping samples are observed using HRTEM. • The optimal defect density is calculated. - Abstract: Bi{sub 2}Sr{sub 2}Ca{sub 1−x}Yb{sub x}Cu{sub 2}O{sub 8+δ} (Bi-2212) single crystals with x = 0.000, 0.005, 0.010 and 0.020 have been prepared by self-flux method. The influences of Yb doping on the formation of the dislocations in the lattice structures, as well as the related current carrying capability are investigated. Due to the SQUID measurement and the Bean model calculation, the maximum critical current density (Jc) is obtained when the Yb doping content is x = 0.010, though the Tc and the carrier concentration are not in the optimal region. Based on the HRTEM analyses of the Ca–O and Cu–O{sub 2} layers, the optimal dislocation density in the Cu–O{sub 2} layers is deduced according to the number of the dislocations per unit area. Besides, the sizes of the dislocations also prove the effectiveness of Yb substitution on the enhancement of the current carrying capability in Bi-2212 single crystals.

  9. Electrochemical impedance spectroscopy analysis of porous silicon prepared by photo-electrochemical etching: current density effect

    Science.gov (United States)

    Husairi, F. S.; Rouhi, J.; Eswar, K. A.; Zainurul, A. Z.; Rusop, M.; Abdullah, S.

    2014-09-01

    Electrical impedance characteristics of porous silicon nanostructures (PSiNs) in frequency function were studied. PSiNs were prepared through photo-electrochemical etching method at various current densities (15-40 mA/cm2) and constant etching time. The atomic force microscope images of PSiNs show that pore diameter and roughness increase when current density increases to 35 mA/cm2. The surface roughness subsequently decreases because of continuous etching of pillars, and a second etching process occurs. Photoluminescence spectra show blue and red shift with increasing applied current density that is attributed to PSiNs size. Variations of electrical resistance and capacitance values of PSiNs were measured using electrochemical impedance spectroscopy analysis. These results indicate that PSiNs prepared at 20 mA/cm2 current density have uniform porous structures with a large number of pillars. Furthermore, this PSiNs structure influences large values of charge transfer resistance and double layer capacitance, indicating potential application in sensors.

  10. Faraday-effect polarimeter-interferometer system for current density measurement on EAST.

    Science.gov (United States)

    Liu, H Q; Jie, Y X; Ding, W X; Brower, D L; Zou, Z Y; Li, W M; Wang, Z X; Qian, J P; Yang, Y; Zeng, L; Lan, T; Wei, X C; Li, G S; Hu, L Q; Wan, B N

    2014-11-01

    A multichannel far-infrared laser-based POlarimeter-INTerferometer (POINT) system utilizing the three-wave technique is under development for current density and electron density profile measurements in the EAST tokamak. Novel molybdenum retro-reflectors are mounted in the inside wall for the double-pass optical arrangement. A Digital Phase Detector with 250 kHz bandwidth, which will provide real-time Faraday rotation angle and density phase shift output, have been developed for use on the POINT system. Initial calibration indicates the electron line-integrated density resolution is less than 5 × 10(16) m(-2) (∼2°), and the Faraday rotation angle rms phase noise is <0.1°.

  11. Finite temperature fermion condensate, charge and current densities in a (2+1)-dimensional conical space

    Energy Technology Data Exchange (ETDEWEB)

    Bellucci, S. [INFN, Laboratori Nazionali di Frascati, Frascati (Italy); Bezerra de Mello, E.R. [Universidade Federal da Parai ba, Departamento de Fisica, 58.059-970, Joao Pessoa, PB (Brazil); Braganca, E. [INFN, Laboratori Nazionali di Frascati, Frascati (Italy); Universidade Federal da Parai ba, Departamento de Fisica, 58.059-970, Joao Pessoa, PB (Brazil); Saharian, A.A. [Yerevan State University, Department of Physics, Yerevan (Armenia)

    2016-06-15

    We evaluate the fermion condensate and the expectation values of the charge and current densities for a massive fermionic field in (2+1)-dimensional conical spacetime with a magnetic flux located at the cone apex. The consideration is done for both irreducible representations of the Clifford algebra. The expectation values are decomposed into the vacuum expectation values and contributions coming from particles and antiparticles. All these contributions are periodic functions of the magnetic flux with the period equal to the flux quantum. Related to the non-invariance of the model under the parity and time-reversal transformations, the fermion condensate and the charge density have indefinite parity with respect to the change of the signs of the magnetic flux and chemical potential. The expectation value of the radial current density vanishes. The azimuthal current density is the same for both the irreducible representations of the Clifford algebra. It is an odd function of the magnetic flux and an even function of the chemical potential. The behavior of the expectation values in various asymptotic regions of the parameters are discussed in detail. In particular, we show that for points near the cone apex the vacuum parts dominate. For a massless field with zero chemical potential the fermion condensate and charge density vanish. Simple expressions are derived for the part in the total charge induced by the planar angle deficit and magnetic flux. Combining the results for separate irreducible representations, we also consider the fermion condensate, charge and current densities in parity and time-reversal symmetric models. Possible applications to graphitic nanocones are discussed. (orig.)

  12. Remarks on time-dependent [current]-density functional theory for open quantum systems.

    Science.gov (United States)

    Yuen-Zhou, Joel; Aspuru-Guzik, Alán

    2013-08-14

    Time-dependent [current]-density functional theory for open quantum systems (OQS) has emerged as a formalism that can incorporate dissipative effects in the dynamics of many-body quantum systems. Here, we review and clarify some formal aspects of these theories that have been recently questioned in the literature. In particular, we provide theoretical support for the following conclusions: (1) contrary to what we and others had stated before, within the master equation framework, there is in fact a one-to-one mapping between vector potentials and current densities for fixed initial state, particle-particle interaction, and memory kernel; (2) regardless of the first conclusion, all of our recently suggested Kohn-Sham (KS) schemes to reproduce the current and particle densities of the original OQS, and in particular, the use of a KS closed driven system, remains formally valid; (3) the Lindblad master equation maintains the positivity of the density matrix regardless of the time-dependence of the Hamiltonian or the dissipation operators; (4) within the stochastic Schrödinger equation picture, a one-to-one mapping from stochastic vector potential to stochastic current density for individual trajectories has not been proven so far, except in the case where the vector potential is the same for every member of the ensemble, in which case, it reduces to the Lindblad master equation picture; (5) master equations may violate certain desired properties of the density matrix, such as positivity, but they remain as one of the most useful constructs to study OQS when the environment is not easily incorporated explicitly in the calculation. The conclusions support our previous work as formally rigorous, offer new insights into it, and provide a common ground to discuss related theories.

  13. Higher-order finite-difference formulation of periodic Orbital-free Density Functional Theory

    CERN Document Server

    Ghosh, Swarnava

    2014-01-01

    We present a real-space formulation and higher-order finite-difference implementation of periodic Orbital-free Density Functional Theory (OF-DFT). Specifically, utilizing a local reformulation of the electrostatic and kernel terms, we develop a generalized framework suitable for performing OF-DFT simulations with different variants of the electronic kinetic energy. In particular, we develop a self-consistent field (SCF) type fixed-point method for calculations involving linear-response kinetic energy functionals. In doing so, we make the calculation of the electronic ground-state and forces on the nuclei amenable to computations that altogether scale linearly with the number of atoms. We develop a parallel implementation of this formulation using the finite-difference discretization, using which we demonstrate that higher-order finite-differences can achieve relatively large convergence rates with respect to mesh-size in both the energies and forces. Additionally, we establish that the fixed-point iteration c...

  14. Laboratory study of magnetic reconnection with a density asymmetry across the current sheet.

    Science.gov (United States)

    Yoo, Jongsoo; Yamada, Masaaki; Ji, Hantao; Jara-Almonte, Jonathan; Myers, Clayton E; Chen, Li-Jen

    2014-08-29

    The effects of a density asymmetry across the current sheet on anti-parallel magnetic reconnection are studied systematically in a laboratory plasma. Despite a significant density ratio of up to 10, the in-plane magnetic field profile is not significantly changed. On the other hand, the out-of-plane Hall magnetic field profile is considerably modified; it is almost bipolar in structure with the density asymmetry, as compared to quadrupolar in structure with the symmetric configuration. Moreover, the ion stagnation point is shifted to the low-density side, and the electrostatic potential profile also becomes asymmetric with a deeper potential well on the low-density side. Nonclassical bulk electron heating together with electromagnetic fluctuations in the lower hybrid frequency range is observed near the low-density-side separatrix. The dependence of the ion outflow and reconnection electric field on the density asymmetry is measured and compared with theoretical expectations. The measured ion outflow speeds are about 40% of the theoretical values.

  15. Conductivity and current density image reconstruction using harmonic Bz algorithm in magnetic resonance electrical impedance tomography.

    Science.gov (United States)

    Oh, Suk Hoon; Lee, Byung Il; Woo, Eung Je; Lee, Soo Yeol; Cho, Min Hyoung; Kwon, Ohin; Seo, Jin Keun

    2003-10-07

    Magnetic resonance electrical impedance tomography (MREIT) is to provide cross-sectional images of the conductivity distribution sigma of a subject. While injecting current into the subject, we measure one component Bz of the induced magnetic flux density B = (Bx, By, Bz) using an MRI scanner. Based on the relation between (inverted delta)2 Bz and inverted delta sigma, the harmonic Bz algorithm reconstructs an image of sigma using the measured Bz data from multiple imaging slices. After we obtain sigma, we can reconstruct images of current density distributions for any given current injection method. Following the description of the harmonic Bz algorithm, this paper presents reconstructed conductivity and current density images from computer simulations and phantom experiments using four recessed electrodes injecting six different currents of 26 mA. For experimental results, we used a three-dimensional saline phantom with two polyacrylamide objects inside. We used our 0.3 T (tesla) experimental MRI scanner to measure the induced Bz. Using the harmonic Bz algorithm, we could reconstruct conductivity and current density images with 82 x 82 pixels. The pixel size was 0.6 x 0.6 mm2. The relative L2 errors of the reconstructed images were between 13.8 and 21.5% when the signal-to-noise ratio (SNR) of the corresponding MR magnitude images was about 30. The results suggest that in vitro and in vivo experimental studies with animal subjects are feasible. Further studies are requested to reduce the amount of injection current down to less than 1 mA for human subjects.

  16. Nanoscale Imaging of Current Density with a Single-Spin Magnetometer.

    Science.gov (United States)

    Chang, K; Eichler, A; Rhensius, J; Lorenzelli, L; Degen, C L

    2017-03-24

    Charge transport in nanostructures and thin films is fundamental to many phenomena and processes in science and technology, ranging from quantum effects and electronic correlations in mesoscopic physics, to integrated charge- or spin-based electronic circuits, to photoactive layers in energy research. Direct visualization of the charge flow in such structures is challenging due to their nanometer size and the itinerant nature of currents. In this work, we demonstrate noninvasive magnetic imaging of current density in two-dimensional conductor networks including metallic nanowires and carbon nanotubes. Our sensor is the electronic spin of a diamond nitrogen-vacancy center attached to a scanning tip and operated under ambient conditions. Using a differential measurement technique, we detect DC currents down to a few μA with a current density noise floor of ∼2 × 10(4) A/cm(2). Reconstructed images have a spatial resolution of typically 50 nm, with a best-effort value of 22 nm. Current density imaging offers a new route for studying electronic transport and conductance variations in two-dimensional materials and devices, with many exciting applications in condensed matter physics and materials science.

  17. High temperature and current density induced degradation of multi-layer graphene

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Baoming; Haque, M. A., E-mail: mah37@psu.edu [Mechanical and Nuclear Engineering, The Pennsylvania State University, 314, Leonhard Building, University Park, Pennsylvania 16802 (United States); Mag-isa, Alexander E.; Kim, Jae-Hyun [Korea Institute of Machinery and Materials, 156 Gajungbuk-ro, Yuseong-gu, Daejeon 305-343 (Korea, Republic of); Lee, Hak-Joo [Korea Institute of Machinery and Materials, 156 Gajungbuk-ro, Yuseong-gu, Daejeon 305-343 (Korea, Republic of); Center for Advanced Meta-Materials (CAMM), 156 Gajungbuk-ro, Yuseong-gu, Daejeon 305-343 (Korea, Republic of)

    2015-10-19

    We present evidence of moderate current density, when accompanied with high temperature, promoting migration of foreign atoms on the surface of multi-layer graphene. Our in situ transmission electron microscope experiments show migration of silicon atoms at temperatures above 800 °C and current density around 4.2 × 10{sup 7} A/cm{sup 2}. Originating from the micro-machined silicon structures that clamp the freestanding specimen, the atoms are observed to react with the carbon atoms in the multi-layer graphene to produce silicon carbide at temperatures of 900–1000 °C. In the absence of electrical current, there is no migration of silicon and only pyrolysis of polymeric residue is observed.

  18. Effects of current density on preparation of grainy electrolytic manganese dioxide

    Institute of Scientific and Technical Information of China (English)

    GUO Hua-jun; ZHU Bing-quan; LI Xin-hai; ZHANG Xin-ming; WANG Zhi-xing; PENG Wen-jie; LIU Lu-ping

    2005-01-01

    Grainy electrolytic manganese dioxide was prepared by electrodeposition in a 0.9 mol/L MnSO4 and 2.5 mol/L H2SO4 solution. The structure, particle size and appearance of the grainy electrolytic manganese dioxide were determined by powder X-ray diffraction, laser particle size analysis and scanning electron micrographs measurements. Current density has important effects on cell voltage, anodic current efficiency and particle size of the grainy electrolytic manganese dioxide, and the optimum current density is 30 A/dm 2. The grainy electrolytic manganese dioxide electrodeposited under the optimum conditions consists of γ-MnO2 with an orthorhombic lattice structure; the grainy electrolytic manganese dioxide has a spherical or sphere-like appearance and a narrow particle size distribution with an average particle diameter of 7.237 μm.

  19. Higher Spin Currents in the Enhanced N=3 Kazama-Suzuki Model

    CERN Document Server

    Ahn, Changhyun

    2016-01-01

    The N=3 Kazama-Suzuki model at the `critical' level has been found by Creutzig, Hikida and Ronne. We construct the lowest higher spin currents of spins (3/2, 2,2,2,5/2, 5/2, 5/2, 3) in terms of various fermions. In order to obtain the operator product expansions (OPEs) between these higher spin currents, we describe three N=2 OPEs between the two N=2 higher spin currents denoted by (3/2, 2, 2, 5/2) and (2, 5/2, 5/2, 3) (corresponding 36 OPEs in the component approach). Using the various Jacobi identities, the coefficient functions appearing on the right hand side of these N=2 OPEs are determined in terms of central charge completely. Then we describe them as one single N=3 OPE in the N=3 superspace. The right hand side of this N=3 OPE contains the SO(3)-singlet N=3 higher spin multiplet of spins (2, 5/2, 5/2, 5/2, 3,3,3, 7/2), the SO(3)-singlet N=3 higher spin multiplet of spins (5/2, 3,3,3, 7/2, 7/2, 7/2, 4), and the SO(3)-triplet N=3 higher spin multiplets where each multiplet has the spins (3, 7/2, 7/2, 7/...

  20. Transport, deposition, and liftoff in laboratory density currents composed of hot particles in air

    Science.gov (United States)

    Andrews, B. J.; Manga, M.

    2010-12-01

    Understanding the dynamics of transport, deposition, and air entrainment in pyroclastic density currents (PDCs) is required for accurate predictions of future current behaviors and interpretations of ancient deposits, but directly observing the interiors of natural PDCs is effectively impossible. We model PDCs with scaled, hot, particle-laden density currents generated in a 6 m long, 0.6 m wide, 1.8 m tall air-filled tank. Comparison of relevant scaling between our experiments and natural PDCs indicates that we are accurately capturing much of the dynamics of dilute PDCs: * Reynolds numbers of our experiments are lower than natural currents, 10^3 compared to 10^6, but still fully turbulent; * Densimetric and Thermal Richardson numbers are of O(1) in both natural and modeled currents; * Stokes and settling numbers for particles in the experiments fall within the expected range for natural PDCs. Conditions within the tank are monitored with temperature and humidity probes. Experiments are illuminated with sheet lighting, and recorded with high-definition video cameras. In general, currents have average velocities of 10-20 cm/s, initial thicknesses of 10-20 cm (although thickness greatly increases as currents entrain and expand air), and run out or lift off distances of 3-5 m. Large Kelvin-Helmholtz type eddies usually form along the top of the current immediately behind the head; these vortices are similar in size to the total current thickness. In currents that lift off, the distal current end typically retreats with time. Preliminary results suggest that lift off distance decreases with increasing thermal Richardson number. Analysis of turbulent structures indicates that the current heads are dominated by large coherent structures with length scales, L, comparable to the current thickness. Within 5-10 L of the current fronts, sequences of similar large eddies often occur. At greater distances behind the current fronts, turbulent structures become smaller and less

  1. Effect of preionization, fluorine concentration, and current density on the discharge uniformity in F2 excimer laser gas mixtures

    Science.gov (United States)

    Mathew, D.; Bastiaens, H. M. J.; Boller, K. J.; Peters, P. J. M.

    2007-08-01

    The discharge homogeneity in F2-based excimer laser gas mixtures and its dependence on various key parameters, such as the degree of preionization, preionization delay time, F2 concentration and current density, is investigated in a small x-ray preionized discharge chamber. The spatial and temporal evolution of the discharges is monitored by taking photographs of the discharge fluorescence with a fast intensified CCD camera. It is found that a preionization electron density of about 107 cm-3 bar-1 is sufficient to initiate a streamer-free homogeneous discharge in gas mixtures of helium and fluorine with multiatmospheric gas pressure. The accompanying optimum time delay between the application of the x-ray pulse and voltage across the discharge electrodes is determined to be about 20 ns. It is shown that in spite of these optimum initial conditions, a homogeneous glow discharge eventually transforms into an inhomogeneous discharge containing numerous filaments. Our experiments show that the higher the initial F2 concentration, the initial current density or the pump power density, the shorter the time interval over which the discharge stays homogeneous. By a quantitative characterization and defining a detailed measure of the observed discharge inhomogeneity we find that halogen depletion, as suggested from the theory, is responsible for the temporal instability of discharges in such laser gas mixtures, as the experimental results are in good agreement with the theory on the halogen depletion instability mechanism.

  2. Role of head of turbulent 3-D density currents in mixing during slumping regime

    Science.gov (United States)

    Bhaganagar, Kiran

    2017-02-01

    A fundamental study was conducted to shed light on entrainment and mixing in buoyancy-driven Boussinesq density currents. Large-eddy simulation was performed on lock-exchange (LE) release density currents—an idealized test bed to generate density currents. As dense fluid was released over a sloping surface into an ambient lighter fluid, the dense fluid slumps to the bottom and forms a characteristic head of the current. The dynamics of the head dictated the mixing processes in LE currents. The key contribution of this study is to resolve an ongoing debate on mixing: We demonstrate that substantial mixing occurs in the early stages of evolution in an LE experiment and that entrainment is highly inhomogeneous and unsteady during the slumping regime. Guided by the flow physics, entrainment is calculated using two different but related perspectives. In the first approach, the entrainment parameter (E) is defined as the fraction of ambient fluid displaced by the head that entrains into the current. It is an indicator of the efficiency in which ambient fluid is displaced into the current and it serves as an important metric to compare the entrainment of dense currents over different types of surfaces, e.g., roughness configuration. In the second approach, E measures the net entrainment in the current at an instantaneous time t over the length of the current. Net entrainment coefficient is a metric to compare the effects of flow dynamical conditions, i.e., lock-aspect ratio that dictates the fraction of buoyancy entering the head, and also the effect of the sloping angle. Together, the entrainment coefficient and the net entrainment coefficient provide an insight into the entrainment process. The "active" head of the current acts as an engine that mixes the ambient fluid with the existing dense fluid, the 3-D lobes and clefts on the frontal end of the current causes recirculation of the ambient fluid into the current, and Kelvin-Helmholtz rolls are the mixers that

  3. Higher spin currents in the enhanced N=3 Kazama-Suzuki model

    Science.gov (United States)

    Ahn, Changhyun; Kim, Hyunsu

    2016-12-01

    The N=3 Kazama-Suzuki model at the `critical' level has been found by Creutzig, Hikida and Ronne. We construct the lowest higher spin currents of spins (3/2,2,2,2,5/2,5/2,5/2,3) in terms of various fermions. In order to obtain the operator product expansions (OPEs) between these higher spin currents, we describe three N=2 OPEs between the two N=2 higher spin currents denoted by (3/2,2,2,5/2) and (2,5/2,5/2,3) (corresponding 36 OPEs in the component approach). Using the various Jacobi identities, the coefficient functions appearing on the right hand side of these N=2 OPEs are deter-mined in terms of central charge completely. Then we describe them as one single N=3 OPE in the N=3 superspace. The right hand side of this N=3 OPE contains the SO(3)-singlet N=3 higher spin multiplet of spins (2,5/2,5/2,5/2,3,3,3,7/2) , the SO(3)-singlet N=3 higher spin multiplet of spins (5/2,3,3,3,7/2,7/2,7/2,4) , and the SO(3)-triplet N=3 higher spin multiplets where each multiplet has the spins (3,7/2,7/2,7/2,4,4,4,9/2) , in addition to N=3 superconformal family of the identity operator. Finally, by factoring out the spin-1/2 current of N=3 linear superconformal algebra generated by eight currents of spins (1/2,1,1,1,3/2,3/2,3/2,2) , we obtain the extension of so-called SO (3) nonlinear Knizhnik Bershadsky algebra.

  4. Comparison between the magnetic and transport critical current densities in high critical current density melt-textured yttrium barium copper-oxide

    Science.gov (United States)

    Gao, L.; Meng, R. L.; Xue, Y. Y.; Hor, P. H.; Chu, C. W.

    1991-01-01

    Using a recently developed pulsed critical current density (Jc) measuring system, the Jc of the high-Jc melt-textured YBa2Cu3O(7-delta) (Y123) bulk samples has been determined. I-V curves with a voltage resolution of 0.5 microV were obtained, and transport Jc's along the a-b plane as high as 7.2 x 10 to the 4th A/sq cm were extracted. These results are comparable to the values obtained magnetically. On the other hand, transport Jc along the c axis were found to be two orders of magnitude smaller, even though the magnetic Jc along the c axis is only about five times smaller than Jc along the a-b plane. It is suggested that for the high-temperature superconducting materials which are highly anisotropic, caution should be taken when using the nontransport magnetic methods to determine Jc.

  5. Non-equilibrium steady states: fluctuations and large deviations of the density and of the current

    Science.gov (United States)

    Derrida, Bernard

    2007-07-01

    These lecture notes give a short review of methods such as the matrix ansatz, the additivity principle or the macroscopic fluctuation theory, developed recently in the theory of non-equilibrium phenomena. They show how these methods allow us to calculate the fluctuations and large deviations of the density and the current in non-equilibrium steady states of systems like exclusion processes. The properties of these fluctuations and large deviation functions in non-equilibrium steady states (for example, non-Gaussian fluctuations of density or non-convexity of the large deviation function which generalizes the notion of free energy) are compared with those of systems at equilibrium.

  6. Current Trends in Malaysian Higher Education and the Effect on Education Policy and Practice: An Overview

    Science.gov (United States)

    Grapragasem, Selvaraj; Krishnan, Anbalagan; Mansor, Azlin Norhaini

    2014-01-01

    Malaysia has evolved from a production-based to knowledge-based economy in order to stay relevant and compete in the global marketplace. Thus, the purpose of this article is to discuss current trends in Malaysian higher education and how these affect education policies and practices. Four main trends are discussed in this study: Globalization,…

  7. Current Approaches to the Assessment of Graphic Design in a Higher Education Context

    Science.gov (United States)

    Giloi, Susan; du Toit, Pieter

    2013-01-01

    This article provides an overview of the current trends in assessment practice within the field of graphic design. The demands placed on educators to apply sound assessment practice for Higher Education subjects is as intense in the field of graphic design as in any other. Forcing the assessment of creative visual work into existing assessment…

  8. Higher order equivalent edge currents for fringe wave radar scattering by perfectly conducting polygonal plates

    DEFF Research Database (Denmark)

    Breinbjerg, Olav

    1992-01-01

    An approach for including higher order edge diffraction in the equivalent edge current (EEC) method is proposed. This approach, which applies to monostatic as well as bistatic radar configurations with perfectly conducting polygonal plates, involves three distinct sets of EECs. All of these sets ...

  9. Current Approaches to the Assessment of Graphic Design in a Higher Education Context

    Science.gov (United States)

    Giloi, Susan; du Toit, Pieter

    2013-01-01

    This article provides an overview of the current trends in assessment practice within the field of graphic design. The demands placed on educators to apply sound assessment practice for Higher Education subjects is as intense in the field of graphic design as in any other. Forcing the assessment of creative visual work into existing assessment…

  10. Responsivity Dependent Anodization Current Density of Nanoporous Silicon Based MSM Photodetector

    Directory of Open Access Journals (Sweden)

    Batool Eneaze B. Al-Jumaili

    2016-01-01

    Full Text Available Achieving a cheap and ultrafast metal-semiconductor-metal (MSM photodetector (PD for very high-speed communications is ever-demanding. We report the influence of anodization current density variation on the response of nanoporous silicon (NPSi based MSM PD with platinum (Pt contact electrodes. Such NPSi samples are grown from n-type Si (100 wafer using photoelectrochemical etching with three different anodization current densities. FESEM images of as-prepared samples revealed the existence of discrete pores with spherical and square-like shapes. XRD pattern displayed the growth of nanocrystals with (311 lattice orientation. The nanocrystallite sizes obtained using Scherrer formula are found to be between 20.8 nm and 28.6 nm. The observed rectifying behavior in the I-V characteristics is ascribed to the Pt/PSi/n-Si Schottky barrier formation, where the barrier height at the Pt/PSi interface is estimated to be 0.69 eV. Furthermore, this Pt/PSi/Pt MSM PD achieved maximum responsivity of 0.17 A/W and quantum efficiency as much as 39.3%. The photoresponse of this NPSi based MSM PD demonstrated excellent repeatability, fast response, and enhanced saturation current with increasing anodization current density.

  11. Density currents in the Chicago River: Characterization, effects on water quality, and potential sources

    Science.gov (United States)

    Jackson, P. Ryan; Garcia, Carlos M.; Oberg, Kevin A.; Johnson, Kevin K.; Garcia, Marcelo H.

    2008-01-01

    Bidirectional flows in a river system can occur under stratified flow conditions and in addition to creating significant errors in discharge estimates, the upstream propagating currents are capable of transporting contaminants and affecting water quality. Detailed field observations of bidirectional flows were made in the Chicago River in Chicago, Illinois in the winter of 2005-06. Using multiple acoustic Doppler current profilers simultaneously with a water-quality profiler, the formation of upstream propagating density currents within the Chicago River both as an underflow and an overflow was observed on three occasions. Density differences driving the flow primarily arise from salinity differences between intersecting branches of the Chicago River, whereas water temperature is secondary in the creation of these currents. Deicing salts appear to be the primary source of salinity in the North Branch of the Chicago River, entering the waterway through direct runoff and effluent from a wastewater-treatment plant in a large metropolitan area primarily served by combined sewers. Water-quality assessments of the Chicago River may underestimate (or overestimate) the impairment of the river because standard water-quality monitoring practices do not account for density-driven underflows (or overflows). Chloride concentrations near the riverbed can significantly exceed concentrations at the river surface during underflows indicating that full-depth parameter profiles are necessary for accurate water-quality assessments in urban environments where application of deicing salt is common.

  12. The antidune question for bedforms in deposits of dilute pyroclastic density currents

    Science.gov (United States)

    Amin Douillet, Guilhem; Kueppers, Ulrich; Dingwell, Donald B.

    2014-05-01

    Dilute pyroclastic density currents (PDCs) are mixture of volcanic particles and gas that can be produced during explosive volcanic eruptions. Like turbidites, they travel on the ground driven by their higher density compared to the ambient fluid, which is due to the load of suspended particles. Dilute PDCs have a low enough particle concentration so that their deposit can contain cross stratification, but high enough so that they do not lift off as ash clouds. Since the 1970's most dune bedform cross stratifications found within dilute PDC deposits have been interpreted as antidunes, mainly due to the fact that they can exhibit more aggradation on the stoss than on the lee side. However, several studies have challenged this interpretation in the last few years (stepwise aggradation, differential draping, flow reversal, near-bed load blocking). In order to decipher which are the valuable arguments to confirm or infirm the antidune interpretation, we document deposits from different eruptions: Tungurahua (Ecuador), Laacher See (Germany), Purrumbete (Australia), Ubehebe (USA), Stromboli (Italy), Yasur (Vanuatu). We consider fluid dynamics arguments on the formation of gravity waves within the shallow water approximation and for internal gravity waves within a stratified medium. Indeed, antidunes are by definition sedimentary prints of stationary gravity waves. We also consider the possibility of cyclic steps as a parental phenomenon for the formation of dilute PDC bedforms. Finally, results of wind tunnel experiments for boundary layer conditions give another independent set of data to interpret cross stratifications within dilute PDC deposits. Whereas we cannot rule out an interpretation as antidunes for some bedforms (lensoidal stoss-depositional structures, low aspect ratio bedforms in train), others can clearly be disregarded based on geometrical considerations. Overall, the interpretation as antidune cannot be simply based on stoss-deposition, and needs to take

  13. Development of Ti-sheathed MgB{sub 2} wires with high critical current density

    Energy Technology Data Exchange (ETDEWEB)

    Liang, G [Department of Physics, Sam Houston State University, Huntsville, TX 77341 (United States); Fang, H [Department of Physics, Sam Houston State University, Huntsville, TX 77341 (United States); Hanna, M [Department of Mechanical Engineering and Texas Center for Superconductivity, University of Houston, Houston, TX 77204-4006 (United States); Yen, F [Texas Center for Superconductivity, University of Houston, Houston, TX 77204-4006 (United States); Lv, B [Department of Chemistry, University of Houston, Houston, TX 77204-5003 (United States); Alessandrini, M [Department of Mechanical Engineering and Texas Center for Superconductivity, University of Houston, Houston, TX 77204-4006 (United States); Keith, S [Department of Physics, Sam Houston State University, Huntsville, TX 77341 (United States); Hoyt, C [Department of Physics, Sam Houston State University, Huntsville, TX 77341 (United States); Tang, Z [Department of Chemistry, University of Houston, Houston, TX 77204-5003 (United States); Salama, K [Department of Mechanical Engineering and Texas Center for Superconductivity, University of Houston, Houston, TX 77204-4006 (United States)

    2006-11-15

    Working towards developing lightweight superconducting magnets for future space and other applications, we have successfully fabricated mono-core Ti-sheathed MgB{sub 2} wires by the powder-in-tube method. The wires were characterized by magnetization, electrical resistivity, x-ray diffraction, scanning electron microscopy, and energy dispersive spectrometry measurements. The results indicate that the Ti sheath does not react with the magnesium and boron, and the present wire rolling process can produce MgB{sub 2} wires with a superconducting volume fraction of at least 64% in the core. Using the Bean model, it was found that at 5 K, the magnetic critical current densities, J{sub c}, measured in magnetic fields of 0, 5, and 8 T are about 4.2 x 10{sup 5}, 3.6 x 10{sup 4}, and 1.4 x 10{sup 4} A cm{sup -2}, respectively. At 20 K and 0 T, the magnetic J{sub c} is about 2.4 x 10{sup 5} A cm{sup -2}. These results show that at zero and low fields, the values of the magnetic J{sub c} for Ti-sheathed MgB{sub 2} wires are comparable with the best results available for the Fe-sheathed MgB{sub 2} wires. At high fields, however, the J{sub c} for Ti-sheathed MgB{sub 2} wires appears higher than that for the Fe-sheathed MgB{sub 2} wires.

  14. Higher Dietary Energy Density is Associated with Stunting but not Overweight and Obesity in a Sample of Urban Malaysian Children.

    Science.gov (United States)

    Shariff, Zalilah Mohd; Lin, Khor Geok; Sariman, Sarina; Siew, Chin Yit; Yusof, Barakatun Nisak Mohd; Mun, Chan Yoke; Lee, Huang Soo; Mohamad, Maznorila

    2016-01-01

    Although diets with high energy density are associated with increased risk of overweight and obesity, it is not known whether such diets are associated with undernutrition. This study assessed the relationship between dietary energy density (ED) and nutritional status of 745 urban 1- to 10-year-old children. Dietary intakes were obtained using food recall and record for two days. Dietary energy density was based on food and caloric beverages. Higher dietary ED was associated with lower intakes of carbohydrate, sugar, vitamins C and D, and calcium but higher fat, fiber, iron, and folate intakes. While intakes of fruits and milk/dairy products decreased, meat, fish, and legume intakes increased with higher dietary ED. Stunting, but not other growth problems, was associated with higher dietary ED. Future studies should confirm the cause-and-effect relationship between higher dietary ED and stunting.

  15. Towards time-dependent current-density-functional theory in the non-linear regime.

    Science.gov (United States)

    Escartín, J M; Vincendon, M; Romaniello, P; Dinh, P M; Reinhard, P-G; Suraud, E

    2015-02-28

    Time-Dependent Density-Functional Theory (TDDFT) is a well-established theoretical approach to describe and understand irradiation processes in clusters and molecules. However, within the so-called adiabatic local density approximation (ALDA) to the exchange-correlation (xc) potential, TDDFT can show insufficiencies, particularly in violently dynamical processes. This is because within ALDA the xc potential is instantaneous and is a local functional of the density, which means that this approximation neglects memory effects and long-range effects. A way to go beyond ALDA is to use Time-Dependent Current-Density-Functional Theory (TDCDFT), in which the basic quantity is the current density rather than the density as in TDDFT. This has been shown to offer an adequate account of dissipation in the linear domain when the Vignale-Kohn (VK) functional is used. Here, we go beyond the linear regime and we explore this formulation in the time domain. In this case, the equations become very involved making the computation out of reach; we hence propose an approximation to the VK functional which allows us to calculate the dynamics in real time and at the same time to keep most of the physics described by the VK functional. We apply this formulation to the calculation of the time-dependent dipole moment of Ca, Mg and Na2. Our results show trends similar to what was previously observed in model systems or within linear response. In the non-linear domain, our results show that relaxation times do not decrease with increasing deposited excitation energy, which sets some limitations to the practical use of TDCDFT in such a domain of excitations.

  16. Influences of urban fabric on pyroclastic density currents at Pompeii (Italy): 1. Flow direction and deposition

    Science.gov (United States)

    Gurioli, L.; Zanella, E.; Pareschi, M. T.; Lanza, R.

    2007-05-01

    To assess ways in which the products of explosive eruptions interact with human settlements, we performed volcanological and rock magnetic analyses on the deposits of the A.D. 79 eruption at the Pompeii excavations (Italy). During this eruption the Roman town of Pompeii was covered by 2.5 m of fallout pumice and then partially destroyed by pyroclastic density currents (PDCs). Anisotropy of magnetic susceptibility measurements performed on the fine matrix of the deposits allowed the quantification of the variations in flow direction and emplacement mechanisms of the parental PDCs that entered the town. These results, integrated with volcanological field investigations, revealed that the presence of buildings, still protruding through the fallout deposits, strongly affected the distribution and accumulation of the erupted products. All of the PDCs that entered the town, even the most dilute ones, were density stratified currents in which interaction with the urban fabric occurred in the lower part of the current. The degree of interaction varied mainly as a function of obstacle height and density stratification within the current. For examples, the lower part of the EU4pf current left deposits up to 3 m thick and was able to interact with 2- to 4-m-high obstacles. However, a decrease in thickness and grain size of the deposits across the town indicates that even though the upper portion of the current was able to decouple from the lower portion, enabling it to flow over the town, it was not able to fully restore the sediment supply to the lower portion in order to maintain the deposition observed upon entry into the town.

  17. The current density in quantum electrodynamics in time-dependent external potentials and the Schwinger effect

    CERN Document Server

    Zahn, Jochen

    2015-01-01

    In the framework of quantum electrodynamics (QED) in external potentials, we introduce a method to compute the time-dependence of the expectation value of the current density for time-dependent homogeneous external electric fields. We apply it to the so-called Sauter pulse. For late times, our results agree with the asymptotic value due to electron-positron pair production. For sub-critical peak field strengths, or results agree very well with the general expression derived by Serber for the linearization in the external field. In particular, the expectation value of the current density at intermediate times can be much greater than at asymptotic times. We comment on consequences of these findings for recent proposals to test the Schwinger effect with high intensity lasers using processes at intermediate times.

  18. Two-dimensional simulations of temperature and current-density distribution in electromigrated structures

    Science.gov (United States)

    Kießig, Birgit; Schäfer, Roland; von Löhneysen, Hilbert

    2014-01-01

    We report on the application of a feedback-controlled electromigration technique for the formation of nanometre-sized gaps in mesoscopic gold wires and rings. The effect of current density and temperature, linked via Joule heating, on the resulting gap size is investigated. Our experiments include in situ measurements of the evolution of the electrical resistance and of the structure of the device during electromigration. Experimentally, a good thermal coupling to the substrate turned out to be crucial to reach electrode spacings below 10 nm and to avoid overall melting of the nanostructures. This finding is supported by numerical calculations of the current-density and temperature profiles for structure layouts subjected to electromigration. The numerical method can be used for optimizing the layout so as to predetermine the location where electromigration leads to the formation of a gap.

  19. Distribution of the Current Density in Electrolyte of the Pem Fuel Cell

    Directory of Open Access Journals (Sweden)

    Eugeniusz Kurgan

    2004-01-01

    Full Text Available In this paper water management in proton exchange membrane (PEM fuel cell is considered. Firt mass convervation law for water is applied. Next proton transport is described by the Nernst-Planck equation and liqid water convection velocity is eliminated by the Schlogl equation. Electro-osmotic drag coefficient is related to hydrogen index and experimentally determined swelling coefficient. Three partial differential equations for molar water concentration Cw, electric potential ϕ and water pressure Pw are formulated. Current density vector i is derived from proton flux expression. These equations together with adequate boundary conditions were solved using finite element method. The distribution of electric potential and current density in function of geometrical parametres is investigated. At the end some illustrative example is given.

  20. Results of Current Density Distribution Mapping in PEM Fuel Cells Dependent on Operation Parameters

    Directory of Open Access Journals (Sweden)

    Zbigniew A. Styczynski

    2013-07-01

    Full Text Available This paper presents in situ measurements of a newly developed current density measurement system for proton exchange membrane fuel cells (PEMFC. While the functional principle and technical evaluation of the measurement system were presented in a previous paper, this paper analyzes the influence of various operation parameters, including multiple start-stop operation, at the anode, cathode and cooling locations on the distribution and long-term development of the current density. The system was operated for 500 h over two years with long periods of inactivity between measurements. The measurement results are evaluated and provide additional information on how to optimize the operation modes of fuel cells, including the start and stop of such systems as well as the water balance.

  1. Simulating the frontal instability of lock-exchange density currents with dissipative particle dynamics

    Science.gov (United States)

    Li, Yanggui; Geng, Xingguo; Wang, Heping; Zhuang, Xin; Ouyang, Jie

    2016-06-01

    The frontal instability of lock-exchange density currents is numerically investigated using dissipative particle dynamics (DPD) at the mesoscopic particle level. For modeling two-phase flow, the “color” repulsion model is adopted to describe binary fluids according to Rothman-Keller method. The present DPD simulation can reproduce the flow phenomena of lock-exchange density currents, including the lobe-and-cleft instability that appears at the head, as well as the formation of coherent billow structures at the interface behind the head due to the growth of Kelvin-Helmholtz instability. Furthermore, through the DPD simulation, some small-scale characteristics can be observed, which are difficult to be captured in macroscopic simulation and experiment.

  2. Current densities of thin filament MgB2/Ti/GlidCop® wire

    Science.gov (United States)

    Kováč, P.; Hušek, I.; Melišek, T.; Kopera, L.

    2011-10-01

    Fine-filamentary MgB2/Ti/GlidCop wire has been produced by an in situ process. Hydrostatic extrusion, drawing and two-axis rolling were used for wire deformation up to the size of 0.2 × 0.2 mm2. An averaged filament size of 7.6-14 µm was obtained for two-axis rolled wire and tape, which are the smallest MgB2 filaments known so far. Very short annealing periods (3-7 min) were used for the thinnest filaments, resulting in a critical current density of ≈12 000 A cm - 2 at 8 T and 4.2 K. The results presented demonstrate the ability to prepare uniform ≈10 µm size and high current density filamentary MgB2 wires in nonmagnetic sheaths, which can be applied for DC and AC coils.

  3. Time-dependent current-density functional theory for generalized open quantum systems.

    Science.gov (United States)

    Yuen-Zhou, Joel; Rodríguez-Rosario, César; Aspuru-Guzik, Alán

    2009-06-14

    In this article, we prove the one-to-one correspondence between vector potentials and particle and current densities in the context of master equations with arbitrary memory kernels, therefore extending time-dependent current-density functional theory (TD-CDFT) to the domain of generalized many-body open quantum systems (OQS). We also analyse the issue of A-representability for the Kohn-Sham (KS) scheme proposed by D'Agosta and Di Ventra for Markovian OQS [Phys. Rev. Lett. 2007, 98, 226403] and discuss its domain of validity. We suggest ways to expand their scheme, but also propose a novel KS scheme where the auxiliary system is both closed and non-interacting. This scheme is tested numerically with a model system, and several considerations for the future development of functionals are indicated. Our results formalize the possibility of practising TD-CDFT in OQS, hence expanding the applicability of the theory to non-Hamiltonian evolutions.

  4. Predicting size effect on diffusion-limited current density of oxygen reduction by copper wire

    Institute of Scientific and Technical Information of China (English)

    LU Yonghong; XU Haibo; WANG Jia; ZHONG Lian

    2011-01-01

    The size effect of copper wire radius (0.04鈥?.82 mm) on the diffusion-limited current density of an oxygen reduction reaction in stagnant simulated seawater (naturally aerated 0.5 mol/L NaCl) is investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) and compared with the results obtained in 0.5 mol/L H2SO4. In the oxygen diffusion-limited range, size effect is found to occur independent of electrolytes, which is attributed to non-linear diffusion. Additionally, to satisfy application in a marine setting, an empirical equation correlating oxygen diffusion-limited current density to copper wire radius is proposed by fitting experimental data.

  5. Strong critical current density enhancement in NiCu/NbN superconducting nanostripes for optical detection

    Science.gov (United States)

    Marrocco, N.; Pepe, G. P.; Capretti, A.; Parlato, L.; Pagliarulo, V.; Peluso, G.; Barone, A.; Cristiano, R.; Ejrnaes, M.; Casaburi, A.; Kashiwazaki, N.; Taino, T.; Myoren, H.; Sobolewski, Roman

    2010-08-01

    We present measurements of ferromagnet/superconductor (NiCu/NbN) and plain superconducting (NbN) nanostripes with the linewidth ranging from 150 to 300 nm. The NiCu (3 nm)/NbN (8 nm) bilayers, as compared to NbN (8 nm), showed a up to six times increase in their critical current density, reaching at 4.2 K the values of 5.5 MA/cm2 for a 150 nm wide nanostripe meander and 12.1 MA/cm2 for a 300 nm one. We also observed six-time sensitivity enhancement when the 150 nm wide NiCu/NbN nanostripe was used as an optical detector. The strong critical current enhancement is explained by the vortex pinning strength and density increase in NiCu/NbN bilayers and confirmed by approximately tenfold increase in the vortex polarizability factor.

  6. Real-time identification of the current density profile in the JET Tokamak: method and validation

    CERN Document Server

    Mazon, Didier; Boulbe, Cédric; Faugeras, Blaise; Boboc, A; Brix, M; De Vries, P; Sharapov, S; Zabeo, L

    2009-01-01

    The real-time reconstruction of the plasma magnetic equilibrium in a Tokamak is a key point to access high performance regimes. Indeed, the shape of the plasma current density profile is a direct output of the reconstruction and has a leading effect for reaching a steady-state high performance regime of operation. In this paper we present the methodology followed to identify numerically the plasma current density in a Tokamak and its equilibrium. In order to meet the real-time requirements a C++ software has been developed using the combination of a finite element method, a nonlinear fixed point algorithm associated to a least square optimization procedure. The experimental measurements that enable the identification are the magnetics on the vacuum vessel, the interferometric and polarimetric measurements on several chords and the motional Stark effect. Details are given about the validation of the reconstruction on the JET tokamak, either by comparison with ?off-line' equilibrium codes or real time software ...

  7. Higher Serum Uric Acid Is Associated with Higher Bone Mineral Density in Chinese Men with Type 2 Diabetes Mellitus

    Directory of Open Access Journals (Sweden)

    Dian-dian Zhao

    2016-01-01

    Full Text Available Accumulating evidence suggests that oxidative stress is associated with osteoporosis. Serum uric acid (UA is a strong endogenous antioxidant. Therefore, we investigated the relationship between the serum UA and BMD in Chinese men with T2DM. In this cross-sectional study of 621 men with T2DM, BMDs at lumbar spine (L2–4, femoral neck (FN, and total hip (TH were measured by dual-energy X-ray absorptiometry (DXA. Serum levels of UA, calcium (Ca, 25-OH vitamin D3 (vitD3, parathyroid hormone (PTH, and creatinine (Cr were also tested. Data analyses revealed that serum UA levels were positively associated with BMD at all sites (p<0.05 in men with T2DM after adjusting for multiple confounders. The serum UA levels were positively correlated with body weight (r=0.322, body mass index (BMI (r=0.331, Ca (r=0.179, and Cr (r=0.239 (p<0.001 and were also positively associated with the concentrations of PTH (r=0.10, p<0.05. When compared with those in the lowest tertile of UA levels, men with T2DM in the highest tertile had a lower prevalence of osteoporosis or osteopenia (adjusted odds ratio 0.54, 95% confidence interval [CI] 0.31–0.95. These data suggest that higher serum levels of UA are associated with higher BMDs and lower risks of osteoporosis in Chinese men with T2DM.

  8. Current Density Functional Theory Using Meta-Generalized Gradient Exchange-Correlation Functionals.

    Science.gov (United States)

    Furness, James W; Verbeke, Joachim; Tellgren, Erik I; Stopkowicz, Stella; Ekström, Ulf; Helgaker, Trygve; Teale, Andrew M

    2015-09-08

    We present the self-consistent implementation of current-dependent (hybrid) meta-generalized gradient approximation (mGGA) density functionals using London atomic orbitals. A previously proposed generalized kinetic energy density is utilized to implement mGGAs in the framework of Kohn-Sham current density functional theory (KS-CDFT). A unique feature of the nonperturbative implementation of these functionals is the ability to seamlessly explore a wide range of magnetic fields up to 1 au (∼235 kT) in strength. CDFT functionals based on the TPSS and B98 forms are investigated, and their performance is assessed by comparison with accurate coupled-cluster singles, doubles, and perturbative triples (CCSD(T)) data. In the weak field regime, magnetic properties such as magnetizabilities and nuclear magnetic resonance shielding constants show modest but systematic improvements over generalized gradient approximations (GGA). However, in the strong field regime, the mGGA-based forms lead to a significantly improved description of the recently proposed perpendicular paramagnetic bonding mechanism, comparing well with CCSD(T) data. In contrast to functionals based on the vorticity, these forms are found to be numerically stable, and their accuracy at high field suggests that the extension of mGGAs to CDFT via the generalized kinetic energy density should provide a useful starting point for further development of CDFT approximations.

  9. New theorem of classical electromagnetism: equilibrium magnetic field and current density are zero inside ideal conductors

    CERN Document Server

    Fiolhais, Miguel C N; Providencia, C; Nordmark, Arne B

    2010-01-01

    We prove a theorem on the magnetic energy minimum in a system of perfect, or ideal, conductors. It is analogous to Thomson's theorem on the equilibrium electric field and charge distribution in a system of conductors. We first prove Thomson's theorem using a variational principle. Our new theorem is then derived by similar methods. We find that magnetic energy is minimized when the current distribution is a surface current density with zero interior magnetic field; perfect conductors are perfectly diamagnetic. The results agree with currents in superconductors being confined near the surface. The theorem implies a generalized force that expels current and magnetic field from the interior of a conductor that loses its resistivity. Examples of solutions that obey the theorem are presented.

  10. Influence of Fast Neutron Irradiation on Critical Current Densities of Bi-2223/Ag Tape

    Institute of Scientific and Technical Information of China (English)

    Duan Zhenzhong

    2004-01-01

    Experimental results on the magnetic field behavior of the critical current in silver sheathed Bi-2223 tapes are presented. The experiments consist of transport and magnetic measurements in a wide temperature range and in external magnetic field up to 6 T. Significant enhancement of the intragrain critical current densities Jc are observed after irradiation with fast neutron. This is attributed to an improvement of flux pinning capability by the neutron induced defects, but the weak link structure is somewhat damaged as evidenced by the small degradation of transport critical current at low field. According to the measurement of remanent magnetic moment before and after irradiation with fast neutron, the connectivity in Bi-2223 tapes is reduced by 50% after irradiated to a fluence of 2 × 1021 m-2, which resulted in the critical currents degradated by a factor of 10%.

  11. Accurate Prediction of Transimpedances and Equivalent Input Noise Current Densities of Tuned Optical Receiver Front Ends

    DEFF Research Database (Denmark)

    Liu, Qing Zhong

    1991-01-01

    Novel analytical expressions have been derived for calculating transimpedances and equivalent input noise current densities of five tuned optical receiver front ends based on PIN diode and MESFETs or HEMTs. Miller's capacitance, which has been omitted in previous studies, has been taken into acco...... into account. The accuracy of the expressions has been verified by using Touchstone simulator. The agreement between the calculated and simulated front end performances is very good....

  12. Non equilibrium steady states: fluctuations and large deviations of the density and of the current

    OpenAIRE

    Derrida, B.

    2007-01-01

    These lecture notes give a short review of methods such as the matrix ansatz, the additivity principle or the macroscopic fluctuation theory, developed recently in the theory of non-equilibrium phenomena. They show how these methods allow to calculate the fluctuations and large deviations of the density and of the current in non-equilibrium steady states of systems like exclusion processes. The properties of these fluctuations and large deviation functions in non-equilibrium steady states (fo...

  13. Divergence of the axial current and fermion density in Gross-Neveu models

    CERN Document Server

    Karbstein, Felix

    2007-01-01

    The divergence of the axial current is used to relate the spatial derivative of the fermion density to the bare fermion mass and scalar/pseudoscalar condensates in 1+1 dimensional Gross-Neveu models. This serves as a novel test of known results, to explain simple features of the continuous chiral model and to resolve a conflict concerning the assignment of baryon number to certain multi-fermion bound states.

  14. Influence of the anodic etching current density on the morphology of the porous SiC layer

    Directory of Open Access Journals (Sweden)

    Anh Tuan Cao

    2014-03-01

    Full Text Available In this report, we fabricated a porous layer in amorphous SiC thin films by using constant-current anodic etching in an electrolyte of aqueous diluted hydrofluoric acid. The morphology of the porous amorphous SiC layer changed as the anodic current density changed: At low current density, the porous layer had a low pore density and consisted of small pores that branched downward. At moderate current density, the pore size and depth increased, and the pores grew perpendicular to the surface, creating a columnar pore structure. At high current density, the porous structure remained perpendicular, the pore size increased, and the pore depth decreased. We explained the changes in pore size and depth at high current density by the growth of a silicon oxide layer during etching at the tips of the pores.

  15. Magnetic resonance electrical impedance tomography (MREIT): conductivity and current density imaging

    Science.gov (United States)

    Seo, Jin Keun; Kwon, Ohin; Woo, Eung Je

    2005-01-01

    This paper reviews the latest impedance imaging technique called Magnetic Resonance Electrical Impedance Tomography (MREIT) providing information on electrical conductivity and current density distributions inside an electrically conducting domain such as the human body. The motivation for this research is explained by discussing conductivity changes related with physiological and pathological events, electromagnetic source imaging and electromagnetic stimulations. We briefly summarize the related technique of Electrical Impedance Tomography (EIT) that deals with cross-sectional image reconstructions of conductivity distributions from boundary measurements of current-voltage data. Noting that EIT suffers from the ill-posed nature of the corresponding inverse problem, we introduce MREIT as a new conductivity imaging modality providing images with better spatial resolution and accuracy. MREIT utilizes internal information on the induced magnetic field in addition to the boundary current-voltage measurements to produce three-dimensional images of conductivity and current density distributions. Mathematical theory, algorithms, and experimental methods of current MREIT research are described. With numerous potential applications in mind, future research directions in MREIT are proposed.

  16. Structural transitions in electron beam deposited Co–carbonyl suspended nanowires at high electrical current densities

    Directory of Open Access Journals (Sweden)

    Gian Carlo Gazzadi

    2015-06-01

    Full Text Available Suspended nanowires (SNWs have been deposited from Co–carbonyl precursor (Co2(CO8 by focused electron beam induced deposition (FEBID. The SNWs dimensions are about 30–50 nm in diameter and 600–850 nm in length. The as-deposited material has a nanogranular structure of mixed face-centered cubic (FCC and hexagonal close-packed (HCP Co phases, and a composition of 80 atom % Co, 15 atom % O and 5 atom % C, as revealed by transmission electron microscopy (TEM analysis and by energy-dispersive X-ray (EDX spectroscopy, respectively. Current (I–voltage (V measurements with current densities up to 107 A/cm2 determine different structural transitions in the SNWs, depending on the I–V history. A single measurement with a sudden current burst leads to a polycrystalline FCC Co structure extended over the whole wire. Repeated measurements at increasing currents produce wires with a split structure: one half is polycrystalline FCC Co and the other half is graphitized C. The breakdown current density is found at 2.1 × 107 A/cm2. The role played by resistive heating and electromigration in these transitions is discussed.

  17. Structural transitions in electron beam deposited Co-carbonyl suspended nanowires at high electrical current densities.

    Science.gov (United States)

    Gazzadi, Gian Carlo; Frabboni, Stefano

    2015-01-01

    Suspended nanowires (SNWs) have been deposited from Co-carbonyl precursor (Co2(CO)8) by focused electron beam induced deposition (FEBID). The SNWs dimensions are about 30-50 nm in diameter and 600-850 nm in length. The as-deposited material has a nanogranular structure of mixed face-centered cubic (FCC) and hexagonal close-packed (HCP) Co phases, and a composition of 80 atom % Co, 15 atom % O and 5 atom % C, as revealed by transmission electron microscopy (TEM) analysis and by energy-dispersive X-ray (EDX) spectroscopy, respectively. Current (I)-voltage (V) measurements with current densities up to 10(7) A/cm(2) determine different structural transitions in the SNWs, depending on the I-V history. A single measurement with a sudden current burst leads to a polycrystalline FCC Co structure extended over the whole wire. Repeated measurements at increasing currents produce wires with a split structure: one half is polycrystalline FCC Co and the other half is graphitized C. The breakdown current density is found at 2.1 × 10(7) A/cm(2). The role played by resistive heating and electromigration in these transitions is discussed.

  18. Energy transportation via MITL by the linear current flow density up to 7 MA/cm

    Science.gov (United States)

    Korolev, V. D.; Bakshaev, Yu. L.; Bartov, A. V.; Blinov, P. I.; Bryzgunov, V. A.; Chernenko, A. S.; Dan'ko, S. A.; Kalinin, Yu. G.; Kingsep, A. S.; Kazakov, E. D.; Smirnov, V. P.; Smirnova, E. A.; Ustroev, G. I.

    2006-10-01

    The transmission properties of the magnetically self-insulated vacuum transporting line (MITL) were studied on the S-300 pulsed power machine (3 MA, 100 ns) at the high linear current flow density up to dI/db = 7 MA/cm. Experiments were carried out with the short line sections with 10 ÷ 15 mm length and 3 ÷ 5 mm vacuum gap. For measuring of the plasma parameters, the frame ICT photography with the nanosecond temporal resolution in the SXR range and ICT (Image Converter Tube) chronography in visible range were used. The X-ray radiation in various ranges was recorded by the XRD with thin filters (SXR) and by the semiconductor detectors (HXR). The information about current transmission efficiency was obtained by means of magnetic loops and low-inductance shunt. It was determined that dense plasma arose on both anode and cathode when the linear current flow density was low enough, dI/db ≤ 1 MA/cm. A dense plasma moves across the vacuum gap with the velocity (1 ÷ 2) × 106 cm/s. By recording the current and hard X-ray radiation it was found that electron losses in the current front did not exceed 10 ÷ 100 kA. Under strong magnetization of electrons r H = mvc/eB Conceptual Project of fusion reactor on the base of fast Z-pinch has been brought about.

  19. Fast electron current density profile and diffusion studies during LHCD in PBX-M

    Energy Technology Data Exchange (ETDEWEB)

    Jones, S.E.; Kesner, J.; Luckhardt, S.; Paoletti, F. [Massachusetts Inst. of Tech., Cambridge, MA (United States). Plasma Fusion Center; von Goeler, S.; Bernabei, S.; Kaita, R. [Princeton Univ., NJ (United States). Plasma Physics Lab.; Rimini, F. [JET Joint Undertaking, Abingdon (United Kingdom)

    1993-08-01

    Successful current profile control experiments using lower hybrid current drive (LCHD) clearly require knowledge of (1) the location of the driven fast electrons and (2) the ability to maintain that location from spreading due to radial diffusion. These issues can be addressed by examining the data from the hard x-ray camera on PBX-M, a unique diagnostic producing two-dimensional, time resolved tangential images of fast electron bremsstrahlung. Using modeling, these line-of-sight images are inverted to extract a radial fast electron current density profile. We note that ``hollow`` profiles have been observed, indicative of off-axis current drive. These profiles can then be used to calculate an upper bound for an effective fast electron diffusion constant: assuming an extremely radially narrow lower hybrid absorption profile and a transport model based on Rax and Moreau, a model fast electron current density profile is calculated and compared to the experimentally derived profile. The model diffusion constant is adjusted until a good match is found. Applied to steady-state quiescent modes on PBX-M, we obtain an upper limit for an effective diffusion constant of about D*=1.1 m{sup 2}/sec.

  20. Limiting current density in bis(trifluoromethylsulfonyl)amide-based ionic liquid for lithium batteries

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jun-Woo; Yoshida, Kazuki; Tachikawa, Naoki; Dokko, Kaoru; Watanabe, Masayoshi [Department of Chemistry and Biotechnology, Yokohama National University, 79-5 Tokiwadai, Hodogaya-ku, Yokohama 240-8501 (Japan)

    2011-02-15

    The physicochemical and electrochemical properties of the binary ionic liquid (IL), lithium bis(trifluoromethylsulfonyl)amide (LiTFSA) dissolved in N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium bis(trifluoromethylsulfonyl)amide (DEMETFSA), were investigated. The ionic conductivity of the binary IL decreased with an increase in LiTFSA concentration. The self-diffusion coefficients of Li{sup +}, DEME{sup +}, and TFSA{sup -} dissolved in the IL were measured by using the pulsed-field-gradient spin-echo (PGSE) NMR method. The self-diffusion coefficient of each ionic species was also found to decrease with increasing concentration of LiTFSA. The limiting current density in the IL electrolyte was evaluated by chronoamperometry using symmetric Li vertical stroke IL vertical stroke Li cell. The results suggest that the diffusion process of Li(I) in the IL dominates the limiting current density in the cell. The highest limiting current density is achieved at a concentration of 0.64 mol dm{sup -3} of LiTFSA. (author)

  1. Influence of current density on microstructure and properties of electrodeposited nickel-alumina composite coatings

    Energy Technology Data Exchange (ETDEWEB)

    Góral, Anna, E-mail: a.goral@imim.pl [Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta St., 30-059 Krakow (Poland); Nowak, Marek [Institute of Non-Ferrous Metals Gliwice, Light Metals Division Skawina, 19 Pilsudskiego St., 32-050 Skawina (Poland); Berent, Katarzyna; Kania, Bogusz [Institute of Metallurgy and Materials Science, Polish Academy of Sciences, 25 Reymonta St., 30-059 Krakow (Poland)

    2014-12-05

    Highlights: • Current density of the electrodeposition affects the incorporation of Al{sub 2}O{sub 3} in Ni matrix. • Ni/Al{sub 2}O{sub 3} composite coatings exhibit changes in crystallographic texture. • The pitting corrosion effects were observed in Ni/Al{sub 2}O{sub 3} coatings. • Residual stresses were decreased with increasing current density and coating thickness. - Abstract: Electrodeposition process is a very promising method for producing metal matrix composites reinforced with ceramic particles. In this method insoluble particles suspended in an electrolytic bath are embedded in a growing metal layer. This paper is focused on the investigations of the nickel matrix nanocomposite coatings with hard α-Al{sub 2}O{sub 3} nano-particles, electrochemically deposited from modified Watts-type baths on steel substrates. The influence of various current densities on the microstructure, residual stresses, texture, hardness and corrosion resistance of the deposited nickel/alumina coatings was investigated. The surface morphology, cross sections of the coatings and distribution of the ceramic particles in the metal matrix were examined by scanning electron microscopy. The phase composition, residual stresses and preferred grain orientation of the coatings were characterized using X-ray diffraction techniques. The coating morphology revealed that α-Al{sub 2}O{sub 3} particles show a distinct tendency to form agglomerates, approximately uniformly distributed into the nickel matrix.

  2. On the study of phase formation and critical current density in superconducting MgB2

    Indian Academy of Sciences (India)

    Suchitra Rajput; Sujeet Chaudhary; Subhash C Kashyap; Pankaj Srivastava

    2006-06-01

    Superconducting bulk MgB2 samples have been synthesized by employing sintering technique without using any additional process steps, generally undertaken in view of the substantial loss of magnesium, during heat treatment. Starting with Mg rich powders having different atomic ratios of Mg : B, as against the nominally required Mg : B = 1 : 2 ratio, we have obtained superconducting MgB2 samples of different characteristics. The effect of excess Mg in the starting mixture and processing temperature on the phase-formation, transition temperature (C) and critical current density (C) have been investigated by electrical transport and a.c. susceptibility measurements. The X-ray diffraction and X-ray photoelectron spectroscopic analyses of MgB2 bulk samples have been carried out to understand the role of excess Mg and the effect of processing temperature. It is established that MgB2 samples with high critical current density can be synthesized from a Mg rich powder having Mg : B in 2 : 2 ratio, at temperatures around 790°C. Critical current density has been found to vary systematically with processing temperature.

  3. Modeling Bubble Flow and Current Density Distribution in an Alkaline Electrolysis Cell

    Directory of Open Access Journals (Sweden)

    Ravichandra S. Jupudi

    2009-12-01

    Full Text Available The effect of bubbles on the current density distribution over the electrodes of an alkaline electrolyzer cell is studied using a two-dimensional computational fluid dynamics model. Model includes Eulerian-Eulerian two-phase flow methodology to model the multiphase flow of Hydrogen and Oxygen with water and the behavior of each phase is accounted for using first principle. Hydrogen/Oxygen evolution, flow field and current density distribution are incorporated in the model to account for the complicated physics involved in the process. Fluent 6.2 is used to solve two-phase flow and electrochemistry is incorporated using UDF (User Defined Function feature of Fluent. Model is validated with mesh refinement study and by comparison with experimental measurements. Model is found to replicate the effect of cell voltage and inter-electrode gap (distance between the electrodes on current density accurately. Further, model is found to capture the existence of optimum cell height. The validated model is expected to be a very useful tool in the design and optimization of alkaline electrolyzer cells.

  4. Iontophoretic Permeation of Lisinopril at Different Current Densities and Drug Concentrations

    Directory of Open Access Journals (Sweden)

    Ashish Jain

    2012-08-01

    Full Text Available Purpose: The purpose of the present work was to assess iontophoretic permeation of Lisinopril at different current densities and concentrations for development of patient-controlled active transdermal system. Methods: In vitro iontophoretic transdermal delivery of Lisinopril across the pigskin was investigated at three different drug concentrations and three different current densities (0.25- 0.75 mA/cm2 in the donor cell of the diffusion apparatus, using cathodal iontophoresis along with the passive controls. Results: For passive permeation, the steady state flux significantly increased with the increasing of donor drug concentration. At all concentration levels, iontophoresis considerably increased the permeation rate compared to passive controls. Iontophoretic transport of Lisinopril was to be found increase with current densities. Flux enhancement was highest at the lowest drug load and lowest at the highest drug load. Conclusion: The obtained results indicate that permeation rate of Lisinopril across the pigskin can be considerably enhanced, controlled or optimized by the use of Iontophoresis technique.

  5. Tin Oxide Nanoparticles: Synthesis, Characterization and Study their Particle Size at Different Current Density

    Directory of Open Access Journals (Sweden)

    Karzan A. Omar

    2013-11-01

    Full Text Available Tin oxide nanoparticles are prepared by electrochemical reduction method using tetrapropylammonium bromide (TPAB and tetrabutylammonium bromide (TBAB as structure directing agent in an organic medium viz. tetrahydrofuran (THF and acetonitrile (ACN in 4:1 ratio by optimizing current density and molar concentration of the ligand. The reduction process takes place under an inert atmosphere of nitrogen over a period of 2 h. Such nanoparticles are prepared by using a simple electrolysis cell in which the sacrificial anode as a commercially available in tin metal sheet and platinum (inert sheet act as a cathode. The parameters such as current density, solvent polarity, distance between electrodes and concentration of stabilizers are used to control the size of nanoparticles. The synthesized tin oxide nanoparticles are characterized by using UV–Visible, FT-IR and SEM–EDS analysis techniques. UV-Visible spectroscopy has revealed the optical band gap to be 4.13, 4.16 and 4.24 ev for (8, 10 and 12 mA/cm2 and the effect of current density on theirs particle size, respectively.

  6. Top-Off Injection and Higher Currents at the Stanford Synchrotron Radiation Lightsource

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Johannes M.; Liu, James C.; Prinz, Alyssa A.; Rokni, Sayed H.; /SLAC

    2011-04-05

    The Stanford Synchrotron Radiation Lightsource (SSRL) at the SLAC National Accelerator Laboratory is a 234 m circumference storage ring for 3 GeV electrons with its synchrotron radiation serving currently 13 beamlines with about 27 experimental stations. It operated for long time with 100 mA peak current provided by usually three injections per day. In July 2009, the maximum beam current was raised to 200 mA. Over the period from June 2009 to March 2010, Top-Off operation started at every beamline. Top-Off, i.e., the injection of electrons into the storage ring with injection stoppers open, is necessary for SSRL to reach its design current of 500 mA. In the future, the maximal power of the injection current will also soon be raised from currently 1.5 W to 5 W. The Radiation Protection Department at SLAC worked with SSRL on the specifications for the safety systems for operation with Top-Off injection and higher beam currents.

  7. Current progress in high cell density yeast bioprocesses for bioethanol production.

    Science.gov (United States)

    Westman, Johan O; Franzén, Carl Johan

    2015-08-01

    High capital costs and low reaction rates are major challenges for establishment of fermentation-based production systems in the bioeconomy. Using high cell density cultures is an efficient way to increase the volumetric productivity of fermentation processes, thereby enabling faster and more robust processes and use of smaller reactors. In this review, we summarize recent progress in the application of high cell density yeast bioprocesses for first and second generation bioethanol production. High biomass concentrations obtained by retention of yeast cells in the reactor enables easier cell reuse, simplified product recovery and higher dilution rates in continuous processes. High local cell density cultures, in the form of encapsulated or strongly flocculating yeast, furthermore obtain increased tolerance to convertible fermentation inhibitors and utilize glucose and other sugars simultaneously, thereby overcoming two additional hurdles for second generation bioethanol production. These effects are caused by local concentration gradients due to diffusion limitations and conversion of inhibitors and sugars by the cells, which lead to low local concentrations of inhibitors and glucose. Quorum sensing may also contribute to the increased stress tolerance. Recent developments indicate that high cell density methodology, with emphasis on high local cell density, offers significant advantages for sustainable second generation bioethanol production.

  8. Effect of a pinning field on the critical current density for current-induced domain wall motion in perpendicular magnetic anisotropy nanowires.

    Science.gov (United States)

    Ooba, Ayaka; Fujimura, Yuma; Takahashi, Kota; Komine, Takashi; Sugita, Ryuji

    2012-09-01

    In this study, the effect of a pinning field on the critical current density for current-induced domain wall motion in nanowires with perpendicular magnetic anisotropy was investigated using micromagnetic simulations. In order to estimate the pinning field in notched nanowires, we conducted wall energy calculations for nanowires with various saturation magnetizations. The pinning field increased as the notch size increased. The pinning field decreased as the saturation magnetization decreased. As a result, the decreased in the pinning field causes the reduction of the critical current density. Therefore, a significant reduction of the critical current density can be obtained by decreasing the saturation magnetization, even if wall pinning occurs.

  9. Higher dimensional bipartite composite systems with the same density matrix: separable, free entangled, or PPT entangled?

    Science.gov (United States)

    Cheng, Wei; Xu, Fang; Li, Hua; Wang, Gang

    2014-04-01

    Given the density matrix of a bipartite quantum state, could we decide whether it is separable, free entangled, or PPT entangled? Here, we give a negative answer to this question by providing a lot of concrete examples of density matrices, some of which are well known. We find that both separability and distillability are dependent on the decomposition of the density matrix. To be more specific, we show that if a given matrix is considered as the density operators of different composite systems, their entanglement properties might be different. In the case of density matrices, we can look them as both and bipartite quantum states and show that their entanglement properties (i.e., separable, free entangled, or PPT entangled) are completely irrelevant to each other.

  10. Power lateral pnp transistor operating with high current density in irradiated voltage regulator

    Directory of Open Access Journals (Sweden)

    Vukić Vladimir Đ.

    2013-01-01

    Full Text Available The operation of power lateral pnp transistors in gamma radiation field was examined by detection of the minimum dropout voltage on heavily loaded low-dropout voltage regulators LM2940CT5, clearly demonstrating their low radiation hardness, with unacceptably low values of output voltage and collector-emitter voltage volatility. In conjunction with previous results on base current and forward emitter current gain of serial transistors, it was possible to determine the positive influence of high load current on a slight improvement of voltage regulator LM2940CT5 radiation hardness. The high-current flow through the wide emitter aluminum contact of the serial transistor above the isolation oxide caused intensive annealing of the positive oxide-trapped charge, leading to decrease of the lateral pnp transistor's current gain, but also a more intensive recovery of the small-signal npn transistors in the control circuit. The high current density in the base area of the lateral pnp transistor immediately below the isolation oxide decreased the concentration of negative interface traps. Consequently, the positive influence of the reduced concentration of the oxide-trapped charge on the negative feedback reaction circuit, together with the favourable effect of reduced interface traps concentration, exceeded negative influence of the annealed oxide-trapped charge on the serial pnp transistor's forward emitter current gain.

  11. Persistent current and Drude weight of one-dimensional interacting fermions on imperfect ring from current lattice density functional theory

    Science.gov (United States)

    Akande, Akinlolu; Sanvito, Stefano

    2016-11-01

    We perform a numerical study of interacting one-dimensional Hubbard rings with a single impurity potential and pierced by a magnetic flux. Our calculations are carried out at the level of current lattice density functional theory (CLDFT) for the Hubbard model and compared to known results obtained in the thermodynamical limit from the Bethe ansatz. In particular, we investigate the effects of disorder and Coulomb interaction on the persistent current (PC) and the Drude weight. It is found that CLDFT is able to accurately describe qualitative and quantitative features of these ground state properties in the presence of disorder and electronic interaction. When the impurity potential is switched off, the CLDFT approach describes well the velocity of the Luttinger liquid excitations as a function of both interaction strength and electron filling. Then, when the impurity scattering potential is finite, we find the PC to vanish as {{L}-{{α\\text{B}}-1}} for large L and independent on the strength of the scattering potential, in good agreement with Luttinger liquid theory.

  12. Amplification of current density modulation in a FEL with an infinite electron beam

    Energy Technology Data Exchange (ETDEWEB)

    Wang, G.; Litvinenko, V.N.; Webb, S.D.

    2011-03-28

    We show that the paraxial field equation for a free electron laser (FEL) in an infinitely wide electron beam with {kappa}-2 energy distribution can be reduced to a fourth ordinary differential equation (ODE). Its solution for arbitrary initial phase space density modulation has been derived in the wave-vector domain. For initial current modulation with Gaussian profile, close form solutions are obtained in space-time domain. In developing an analytical model for a FEL-based coherent electron cooling system, an infinite electron beam has been assumed for the modulation and correction processes. While the assumption has its limitation, it allows for an analytical close form solution to be obtained, which is essential for investigating the underlying scaling law, benchmarking the simulation codes and understanding the fundamental physics. 1D theory was previously applied to model a CeC FEL amplifier. However, the theory ignores diffraction effects and does not provide the transverse profile of the amplified electron density modulation. On the other hand, 3D theories developed for a finite electron beam usually have solutions expanded over infinite number of modes determined by the specific transverse boundary conditions. Unless the mode with the largest growth rate substantially dominates other modes, both evaluation and extracting scaling laws can be complicated. Furthermore, it is also preferable to have an analytical FEL model with assumptions consistent with the other two sections of a CeC system. Recently, we developed the FEL theory in an infinitely wide electron beam with {kappa}-1 (Lorentzian) energy distribution. Close form solutions have been obtained for the amplified current modulation initiated by an external electric field with various spatial-profiles. In this work, we extend the theory into {kappa}-2 energy distribution and study the evolution of current density induced by an initial density modulation.

  13. Analysis of nanosecond breaking of a high-density current in SOS diodes

    Science.gov (United States)

    Grekhov, I. V.; Lyublinskii, A. G.; Smirnova, I. A.

    2015-11-01

    Effect of a sharp (nanosecond) breaking of the reverse current with a density on the order of 103-104 A/cm2 in a silicon diode upon switching from direct to reverse bias voltage (so-called silicon opening switch, or SOS effect) is widely used in nanosecond technologies of gigawatt powers. For detailed analysis of the SOS effect, we constructed a special setup with small stray inductance, which makes it possible to test single SOS diodes with a working area of 1-2 mm2 in a wide range of current densities. Our experiments show, in particular, that the numerical model of the SOS effect developed at the Institute of Electrophysics, Ural Branch, Russian Academy of Sciences successfully described the experimental results. It is also shown that the charge extracted from the diode structure by the reverse current exceeds the charge introduced by a direct current pulse by not more than 10%, indicating a relatively small role of ionization processes. The possibility to carry out experiments on single samples with a small surface area allows us to study the SOS effect and considerably facilitates investigations aimed at the perfection of the design of SOS diodes.

  14. Micromagnetic model for studies on Magnetic Tunnel Junction switching dynamics, including local current density

    Energy Technology Data Exchange (ETDEWEB)

    Frankowski, Marek, E-mail: mfrankow@agh.edu.pl; Czapkiewicz, Maciej; Skowronski, Witold; Stobiecki, Tomasz

    2014-02-15

    We present a model introducing the Landau–Lifshitz–Gilbert equation with a Slonczewski's Spin-Transfer-Torque (STT) component in order to take into account spin polarized current influence on the magnetization dynamics, which was developed as an Object Oriented MicroMagnetic Framework extension. We implement the following computations: magnetoresistance of vertical channels is calculated from the local spin arrangement, local current density is used to calculate the in-plane and perpendicular STT components as well as the Oersted field, which is caused by the vertical current flow. The model allows for an analysis of all listed components separately, therefore, the contribution of each physical phenomenon in dynamic behavior of Magnetic Tunnel Junction (MTJ) magnetization is discussed. The simulated switching voltage is compared with the experimental data measured in MTJ nanopillars.

  15. Current Density-Functional Theory using meta-Generalized Gradient Exchange--Correlation Functionals

    CERN Document Server

    Furness, James W; Tellgren, Erik I; Stopkowicz, Stella; Ekström, Ulf; Helgaker, Trygve; Teale, Andrew M

    2015-01-01

    We present the self-consistent implementation of current-dependent (hybrid) meta generalized gradient approximation (mGGA) density functionals using London atomic orbitals. A previously proposed generalized kinetic energy density is utilized to implement mGGAs in the framework of Kohn--Sham current density-functional theory (KS-CDFT). A unique feature of the non-perturbative implementation of these functionals is the ability to seamlessly explore a wide range of magnetic fields up to 1 a.u. ($\\sim 235000$T) in strength. CDFT functionals based on the TPSS and B98 forms are investigated and their performance is assessed by comparison with accurate CCSD(T) data. In the weak field regime magnetic properties such as magnetizabilities and NMR shielding constants show modest but systematic improvements over GGA functionals. However, in strong field regime the mGGA based forms lead to a significantly improved description of the recently proposed perpendicular paramagnetic bonding mechanism, comparing well with CCSD(T...

  16. The operator product expansion between the 16 lowest higher spin currents in the N=4 superspace

    Science.gov (United States)

    Ahn, Changhyun; Kim, Man Hea

    2016-07-01

    Some of the operator product expansions (OPEs) between the lowest 16 higher spin currents of spins (1, 3/2, 3/2, 3/2, 3/2, 2, 2, 2, 2, 2, 2, 5/2, 5/2, 5/2, 5/2, 3) in an extension of the large N=4 linear superconformal algebra were constructed in N=4 superconformal coset SU(5)/SU(3) theory previously. In this paper, by rewriting these OPEs in the N=4 superspace developed by Schoutens (and other groups), the remaining undetermined OPEs in which the corresponding singular terms possess the composite fields with spins s =7/2, 4, 9/2, 5 are completely determined. Furthermore, by introducing arbitrary coefficients in front of the composite fields on the right-hand sides of the above complete 136 OPEs, reexpressing them in the N=2 superspace, and using the N=2 OPEs Mathematica package by Krivonos and Thielemans, the complete structures of the above OPEs with fixed coefficient functions are obtained with the help of various Jacobi identities. We then obtain ten N=2 super OPEs between the four N=2 higher spin currents denoted by (1, 3/2, 3/2, 2), (3/2, 2, 2, 5/2), (3/2, 2, 2, 5/2), and (2, 5/2, 5/2, 3) (corresponding 136 OPEs in the component approach) in the N=4 superconformal coset SU(N+2)/SU(N) theory. Finally, we describe them as one single N=4 super OPE between the above 16 higher spin currents in the N=4 superspace. The fusion rule for this OPE contains the next 16 higher spin currents of spins of (2, 5/2, 5/2, 5/2, 5/2, 3, 3, 3, 3, 3, 3, 7/2, 7/2, 7/2, 7/2, 4) in addition to the quadratic N=4 lowest higher spin multiplet and the large N=4 linear superconformal family of the identity operator. The various structure constants (fixed coefficient functions) appearing on the right-hand side of this OPE depend on N and the level k of the bosonic spin-1 affine Kac-Moody current. For convenience, the above 136 OPEs in the component approach for generic ( N, k) with simplified notation are given.

  17. Three-Dimensional Nanometer Features of Direct Current Electrical Trees in Low-Density Polyethylene.

    Science.gov (United States)

    Pallon, Love K H; Nilsson, Fritjof; Yu, Shun; Liu, Dongming; Diaz, Ana; Holler, Mirko; Chen, Xiangrong R; Gubanski, Stanislaw; Hedenqvist, Mikael S; Olsson, Richard T; Gedde, Ulf W

    2017-03-08

    Electrical trees are one reason for the breakdown of insulating materials in electrical power systems. An understanding of the growth of electrical trees plays a crucial role in the development of reliable high voltage direct current (HVDC) power grid systems with transmission voltages up to 1 MV. A section that contained an electrical tree in low-density polyethylene (LDPE) has been visualized in three dimensions (3D) with a resolution of 92 nm by X-ray ptychographic tomography. The 3D imaging revealed prechannel-formations with a lower density with the width of a couple of hundred nanometers formed around the main branch of the electrical tree. The prechannel structures were partially connected with the main tree via paths through material with a lower density, proving that the tree had grown in a step-by-step manner via the prestep structures formed in front of the main channels. All the prechannel structures had a size well below the limit of the Paschen law and were thus not formed by partial discharges. Instead, it is suggested that the prechannel structures were formed by electro-mechanical stress and impact ionization, where the former was confirmed by simulations to be a potential explanation with electro-mechanical stress tensors being almost of the same order of magnitude as the short-term modulus of low-density polyethylene.

  18. Effects of the current boundary conditions at the plasma-gun gap on density in SSPX

    Science.gov (United States)

    Kolesnikov, Roman; Lodestro, L. L.; Meyer, W. H.

    2012-10-01

    The Sustained Spheromak Physics Experiment (SSPX) was a toroidal magnetic-confinement device without toroidal magnetic-field coils or a central transformer but which generated core-plasma currents by dynamo processes driven by coaxial plasma-gun injection into a flux-conserving vessel. Record electron temperatures in a spheromak (Te˜500eV) were achieved, and final results of the SSPX program were reported in [1]. Plasma density, which depended strongly on wall conditions, was an important parameter in SSPX. It was observed that density rises with Igun and that confinement improved as the density was lowered. Shortly after the last experiments, a new feature was added to the Corsica code's solver used to reconstruct SSPX equilibria. Motivated by n=0 fields observed in NIMROD simulations of SSPX, an insulating boundary condition was implemented at the plasma-gun gap. Using this option we will perform new reconstructions of SSPX equilibria and look for correlations between the location of the separatrix (which moves up the gun wall and onto the insulating gap as Igun increases) and plasma density and magnetic-flux amplification [2].[4pt] [1] H. S. McLean, APS, DPP, Dallas, TX, 2008.[0pt] [2] E. B. Hooper et al., Nucl. Fusion 47, 1064 (2007).

  19. Water Dissociation Phenomena on a Bipolar Membrane——Current-voltage Curve in Relation with Ionic Transport and Limiting Current Density

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The water dissociation mechanism on a bipolar membrane under the electrical field was investigated and characterized in terms of ionic transport and limiting current density. It is considered that the depletion layer exists at the junction of a bipolar membrane, which is coincided with the viewpoint of the most literatures, but we also consider that the thickness and conductivity of this layer is not only related with the increase of the applied voltage but also with the limiting current density. Below the limiting current density, the thickness of the depletion layer keeps a constant and the conductivity decreases with the increase of the applied voltage;while above the limiting current density, the depletion thickness will increase with the increase of the applied voltage and the conductivity keeps a very low constant. Based on the data reported in the literatures and independent determinations, the limiting current density was calculated and the experimental curves Ⅰ- Ⅴ in the two directions were compared with the theoretical calculations. It is demonstrated that above the limiting current density, the experimental results,either in the L-H direction or in the H-L direction, are consistent with the theoretical calculations; below the limiting current density, a slight deviation exists between the experimental and the theoretical results, and between the experimental results in the two directions. The change in Donnan potential due to the asymmetry of the mono-layers and the changes of ionic composition in the two directions is possibly responsible for this deviation.

  20. Force-free collisionless current sheet models with non-uniform temperature and density profiles

    Science.gov (United States)

    Wilson, F.; Neukirch, T.; Allanson, O.

    2017-09-01

    We present a class of one-dimensional, strictly neutral, Vlasov-Maxwell equilibrium distribution functions for force-free current sheets, with magnetic fields defined in terms of Jacobian elliptic functions, extending the results of Abraham-Shrauner [Phys. Plasmas 20, 102117 (2013)] to allow for non-uniform density and temperature profiles. To achieve this, we use an approach previously applied to the force-free Harris sheet by Kolotkov et al. [Phys. Plasmas 22, 112902 (2015)]. In one limit of the parameters, we recover the model of Kolotkov et al. [Phys. Plasmas 22, 112902 (2015)], while another limit gives a linear force-free field. We discuss conditions on the parameters such that the distribution functions are always positive and give expressions for the pressure, density, temperature, and bulk-flow velocities of the equilibrium, discussing the differences from previous models. We also present some illustrative plots of the distribution function in velocity space.

  1. Obtaining the Probability Vector Current Density in Canonical Quantum Mechanics by Linear Superposition

    CERN Document Server

    Kauffmann, Steven Kenneth

    2013-01-01

    The quantum mechanics status of the probability vector current density has long seemed to be marginal. On one hand no systematic prescription for its construction is provided, and the special examples of it that are obtained for particular types of Hamiltonian operator could conceivably be attributed to happenstance. On the other hand this concept's key physical interpretation as local average particle flux, which flows from the equation of continuity that it is supposed to satisfy in conjunction with the probability scalar density, has been claimed to breach the uncertainty principle. Given the dispiriting impact of that claim, we straightaway point out that the subtle directional nature of the uncertainty principle makes it consistent with the measurement of local average particle flux. We next focus on the fact that the unique closed-form linear-superposition quantization of any classical Hamiltonian function yields in tandem the corresponding unique linear-superposition closed-form divergence of the proba...

  2. One-dimensional transport of interacting particles: currents, density profiles, phase diagrams, and symmetries.

    Science.gov (United States)

    Dierl, Marcel; Einax, Mario; Maass, Philipp

    2013-06-01

    Driven lattice gases serve as canonical models for investigating collective transport phenomena and properties of nonequilibrium steady states. Here we study one-dimensional transport with nearest-neighbor interactions both in closed bulk systems and in open channels coupled to two particle reservoirs at the ends of the channel. For the widely employed Glauber rates we derive an exact current-density relation in the bulk for unidirectional hopping. An approach based on time-dependent density functional theory provides a good description of the kinetics. For open systems, the system-reservoir couplings are shown to have a striking influence on boundary-induced phase diagrams. The role of particle-hole symmetry is discussed, and its consequence for the topology of the phase diagrams. It is furthermore demonstrated that systems with weak bias can be mapped onto systems with unidirectional hopping.

  3. Density effect on critical current density and flux pinning properties of polycrystalline SmFeAsO1 - xFx superconductor

    Science.gov (United States)

    Ding, Y.; Sun, Y.; Zhuang, J. C.; Cui, L. J.; Shi, Z. X.; Sumption, M. D.; Majoros, M.; Susner, M. A.; Kovacs, C. J.; Li, G. Z.; Collings, E. W.; Ren, Z. A.

    2011-12-01

    A series of polycrystalline SmFeAs1 - xOx bulks was prepared to systematically investigate the influence of sample density on flux pinning properties. Different sample densities were achieved by controlling the pelletizing pressure. The superconducting volume fraction, the critical current densities Jcm and the flux pinning force densities Fp were estimated from the magnetization measurements. Experimental results show that: (1) the superconducting volume fraction increases with the increasing of sample density; (2) the Jcm values have a similar trend except for the sample with very high density due to different connectivity and pinning mechanisms, moreover, the Jcm(B) curve develops a peak effect at approximately the same field at which the high density sample shows a kink; (3) the Fp(B) curve of the high density sample shows a low-field peak and a high-field peak at several temperatures, which can be explained by improved intergranular current, while only one peak can be observed in Fp(B) of the low density samples. Based on the scaling behaviour of flux pinning force densities, the main intragranular pinning is normal point pinning.

  4. High-current-density gun with a LaB6 cathode

    Science.gov (United States)

    Ebihara, K.; Hiramatsu, S.

    1996-08-01

    To develop a high-current electron gun for an induction linac, a prototype of a Pierce-type electron gun using planar 12-mm-diam lanthanum hexaboride (LaB6) is studied as a thermionic emitter at high current densities. The cathode is heated up to temperatures of 1750 °C by electron bombardment and thermal radiation from a tungsten heater. The heater that has the highest temperature in the gun is thermally isolated from the outer vacuum chamber with heat shields. The bombardment voltage of ˜1 kV is typically applied to a gap between the cathode and the heater. The gun has been operated up to voltages of 55 kV, obtaining a maximum current density of 20 A/cm2 with a pulse width of 250 ns at a cathode temperature of 1600 °C. High-voltage pulsing results show that the gun, with applied voltages of over 40 kV, is operated in space-charge-limited region at temperatures of over 1600 °C; also it is operated in a temperature-limited region at temperatures of less than 1500 °C. An effective work function of 2.68 eV is obtained. The cathode, when heated up to 1600 °C, emits over 7 A of electrons with a ˜20% reduction after 850 h of continuous operation. These measurements were made between vacuum pressures of 10-6 and 10-7 Torr.

  5. Ultrahigh-current-density metal-ion implantation and diamondlike-hydrocarbon films for tribological applications

    Science.gov (United States)

    Wilbur, P. J.

    1993-09-01

    The metal-ion-implantation system used to implant metals into substrates are described. The metal vapor required for operation is supplied by drawing sufficient electron current from the plasma discharge to an anode-potential crucible so a solid, pure metal placed in the crucible will be heated to the point of vaporization. The ion-producing, plasma discharge is initiated within a graphite-ion-source body, which operates at high temperature, by using an argon flow that is turned off once the metal vapor is present. Extraction of ion beams several cm in diameter at current densities ranging to several hundred micro-A/sq cm on a target 50 cm downstream of the ion source were demonstrated using Mg, Ag, Cr, Cu, Si, Ti, V, B, and Zr. These metals were implanted into over 100 substrates (discs, pins, flats, wires). A model describing thermal stresses induced in materials (e.g. ceramic plates) during high-current-density implantation is presented. Tribological and microstructural characteristics of iron and 304-stainless-steel samples implanted with Ti or B are examined. Diamondlike-hydrocarbon coatings were applied to steel surfaces and found to exhibit good tribological performance.

  6. The influence of critical current density of Bi-2212 superconductors by defects after Yb-doping

    Science.gov (United States)

    Lu, Tianni; Zhang, Cuiping; Guo, Shengwu; Wu, Yifang; Li, Chengshan; Zhou, Lian

    2015-12-01

    Bi2Sr2Ca1-xYbxCu2O8+δ (Bi-2212) single crystals with x = 0.000, 0.005, 0.010 and 0.020 have been prepared by self-flux method. The influences of Yb doping on the formation of the dislocations in the lattice structures, as well as the related current carrying capability are investigated. Due to the SQUID measurement and the Bean model calculation, the maximum critical current density (Jc) is obtained when the Yb doping content is x = 0.010, though the Tc and the carrier concentration are not in the optimal region. Based on the HRTEM analyses of the Ca-O and Cu-O2 layers, the optimal dislocation density in the Cu-O2 layers is deduced according to the number of the dislocations per unit area. Besides, the sizes of the dislocations also prove the effectiveness of Yb substitution on the enhancement of the current carrying capability in Bi-2212 single crystals.

  7. Quasi-1D van der Waals materials as high current-density local interconnects (Conference Presentation)

    Science.gov (United States)

    Stolyarov, Maxim; Aytan, Ece; Bloodgood, Matthew; Salguero, Tina T.; Balandin, Alexander A.

    2016-09-01

    The continuous downscaling of interconnect dimensions in combination with the introduction of low-k dielectrics has increased the number of heat dissipation, integration and reliability challenges in modern electronics. As a result, there is a strong need for new materials that have high current-carrying capacity for applications as nanoscale interconnects. In this presentation, we show that quasi-one-dimensional (1D) van der Waals metals such as TaSe3 have excellent breakdown current density exceeding that of 5 MA/cm2. This value is above that currently achievable in conventional copper or aluminum wires. The quasi-1D van der Waals materials are characterized by strong bonds along one dimension and weak van der Waals bonds along two other dimensions. The material for this study was grown by the chemical vapor transport (CVT) method. Both mechanical and chemical exfoliation methods were used to fabricate nanowires with lateral dimensions below 100 nm. The dimensions of the quasi-1D nanowires were verified with scanning electron microscopy (SEM) and atomic force microscopy (AFM). The metal (Ti/Au) contacts for the electrical characterization were deposited using electron beam evaporation (EBE). The measurements were conducted on a number of prototype interconnects with multiple electric contacts to ensure reproducibility. The obtained results suggest that quasi-1D van der Waals metals present a feasible alternative to conventional copper interconnects in terms of the current-carrying capacity and the breakdown current-density. This work was supported, in part, by the SRC and DARPA through STARnet Center for Function Accelerated nanoMaterial Engineering (FAME).

  8. Invariance in current dipole moment density across brain structures and species: physiological constraint for neuroimaging.

    Science.gov (United States)

    Murakami, Shingo; Okada, Yoshio

    2015-05-01

    Although anatomical constraints have been shown to be effective for MEG and EEG inverse solutions, there are still no effective physiological constraints. Strength of the current generator is normally described by the moment of an equivalent current dipole Q. This value is quite variable since it depends on size of active tissue. In contrast, the current dipole moment density q, defined as Q per surface area of active cortex, is independent of size of active tissue. Here we studied whether the value of q has a maximum in physiological conditions across brain structures and species. We determined the value due to the primary neuronal current (q primary) alone, correcting for distortions due to measurement conditions and secondary current sources at boundaries separating regions of differing electrical conductivities. The values were in the same range for turtle cerebellum (0.56-1.48 nAm/mm(2)), guinea pig hippocampus (0.30-1.34 nAm/mm(2)), and swine neocortex (0.18-1.63 nAm/mm(2)), rat neocortex (~2.2 nAm/mm(2)), monkey neocortex (~0.40 nAm/mm(2)) and human neocortex (0.16-0.77 nAm/mm(2)). Thus, there appears to be a maximum value across the brain structures and species (1-2 nAm/mm(2)). The empirical values closely matched the theoretical values obtained with our independently validated neural network model (1.6-2.8 nAm/mm(2) for initial spike and 0.7-3.1 nAm/mm(2) for burst), indicating that the apparent invariance is not coincidental. Our model study shows that a single maximum value may exist across a wide range of brain structures and species, varying in neuron density, due to fundamental electrical properties of neurons. The maximum value of q primary may serve as an effective physiological constraint for MEG/EEG inverse solutions.

  9. Planar gradient coil design by scaling the spatial frequencies of minimum-inductance current density.

    Science.gov (United States)

    Lee, S Y; Park, B S; Yi, J H; Yi, W

    1997-11-01

    Gradient coil inductance has been remarkably reduced by the minimum-inductance design technique, which minimizes the magnetic energy stored by the gradient coil. The planar gradient coil designed by this technique, however, often has poor magnetic field linearity. Scaling the spatial frequencies of the current density function derived by this method, the magnetic field linearity of the planar gradient coil can be greatly improved with a small sacrifice of gradient coil inductance. A figure of merit of the planar gradient coil has been found to be improved by scaling the spatial frequencies.

  10. Correlations of the density and of the current in non-equilibrium diffusive systems

    Science.gov (United States)

    Sadhu, Tridib; Derrida, Bernard

    2016-11-01

    We use fluctuating hydrodynamics to analyze the dynamical properties in the non-equilibrium steady state of a diffusive system coupled with reservoirs. We derive the two-time correlations of the density and of the current in the hydrodynamic limit in terms of the diffusivity and the mobility. Within this hydrodynamic framework we discuss a generalization of the fluctuation dissipation relation in a non-equilibrium steady state where the response function is expressed in terms of the two-time correlations. We compare our results to an exact solution of the symmetric exclusion process. This exact solution also allows one to directly verify the fluctuating hydrodynamics equation.

  11. Density and current profiles in Uq (A2(1)) zero range process

    Science.gov (United States)

    Kuniba, A.; Mangazeev, V. V.

    2017-09-01

    The stochastic R matrix for Uq (An(1)) introduced recently gives rise to an integrable zero range process of n classes of particles in one dimension. For n = 2 we investigate how finitely many first class particles fixed as defects influence the grand canonical ensemble of the second class particles. By using the matrix product stationary probabilities involving infinite products of q-bosons, exact formulas are derived for the local density and current of the second class particles in the large volume limit.

  12. A class of vector identities relevant to the representation of the electric current density

    CERN Document Server

    Bornatici, M

    2007-01-01

    A rigorous mathematical proof is given of a class of vector identities that provide a way to separate an arbitrary vector field (over a linear space) into the sum of a radial (i.e., pointing toward the radial unit vector) vector field, minus the divergence of a tensor plus the curl of an axial vector. Such a separation is applied to the representation of electric current densities yielding a specific form of the effective polarization and magnetization fields which is also discussed in some details.

  13. Temperature-dependence of Threshold Current Density-Length Product in Metallization Lines: A Revisit

    Science.gov (United States)

    Saptono Duryat, Rahmat; Kim, Choong-Un

    2016-04-01

    One of the important phenomena in Electromigration (EM) is Blech Effect. The existence of Threshold Current Density-Length Product or EM Threshold has such fundamental and technological consequences in the design, manufacture, and testing of electronics. Temperature-dependence of Blech Product had been thermodynamically established and the real behavior of such interconnect materials have been extensively studied. The present paper reviewed the temperature-dependence of EM threshold in metallization lines of different materials and structure as found in relevant published articles. It is expected that the reader can see a big picture from the compiled data, which might be overlooked when it was examined in pieces.

  14. Analysis of reliability metrics and quality enhancement measures in current density imaging.

    Science.gov (United States)

    Foomany, F H; Beheshti, M; Magtibay, K; Masse, S; Foltz, W; Sevaptsidis, E; Lai, P; Jaffray, D A; Krishnan, S; Nanthakumar, K; Umapathy, K

    2013-01-01

    Low frequency current density imaging (LFCDI) is a magnetic resonance imaging (MRI) technique which enables calculation of current pathways within the medium of study. The induced current produces a magnetic flux which presents itself in phase images obtained through MRI scanning. A class of LFCDI challenges arises from the subject rotation requirement, which calls for reliability analysis metrics and specific image registration techniques. In this study these challenges are formulated and in light of proposed discussions, the reliability analysis of calculation of current pathways in a designed phantom and a pig heart is presented. The current passed is measured with less than 5% error for phantom, using CDI method. It is shown that Gauss's law for magnetism can be treated as reliability metric in matching the images in two orientations. For the phantom and pig heart the usefulness of image registration for mitigation of rotation errors is demonstrated. The reliability metric provides a good representation of the degree of correspondence between images in two orientations for phantom and pig heart. In our CDI experiments this metric produced values of 95% and 26%, for phantom, and 88% and 75% for pig heart, for mismatch rotations of 0 and 20 degrees respectively.

  15. THE PECULIARITIES OF THE U. S. HIGHER EDUCATION DEVELOPMENT STRATEGY IN THE CONTEXT OF CURRENT CONDITIONS

    Directory of Open Access Journals (Sweden)

    Olga I. Fomina

    2014-01-01

    Full Text Available Abstract. The aim of the research is to investigate a current state of the US higher education and to show obstacles in a way of its innovative perfection; to reveal specificity of the US state policy concerning the higher school; to define factors that influence the effectiveness of the American research universities during the last decades. Methods. The author applies for methods of the retrospective and logic analysis while considering social and economic conditions and features of functioning of the American higher educational institutions during the latter half of 20th – the early 21st centuries. Conclusions on a condition and prospects of development of the US higher education are made on the basis of the review and the author’s interpretation of original documentary sources tenor and the official statistical data. Results. The author specifies the groups of factors that provide functioning efficiency of leading research universities of the USA. The research findings demonstrate that the diversification of funding sources, the concentration of talents in professorial, scientific, student communities, the guarantee of the academic mobility, and the favorable management structure of the US universities allow to lower dependence on economic instability, to provide development dynamism and adequately react to present calls. The characteristic of the system developed in the present period of the US higher education is given; the directions of its innovative development in modern conditions are defined. Scientific novelty. The author singles out and proves the problems of the US higher school caused by an economic crisis in the early 21st century and essentially affected the state strategy in educational management sphere and the corporate policy of high schools, taking into consideration the inescapable fact that features of the US higher education system are caused by aspiration of this state to hold the leading positions in the world

  16. Critical current densities and irreversibility fields of MgB 2 bulks

    Science.gov (United States)

    Kumakura, H.; Takano, Y.; Fujii, H.; Togano, K.; Kito, H.; Ihara, H.

    2001-11-01

    We prepared two MgB 2 bulks by applying conventional sintering and high-pressure sintering methods, and compared the current carrying properties. Jc obtained by the resistive method was larger than that obtained by the magnetic method. Jc- B curves obtained by the resistive method showed no history effect. These results indicate that most of the superconducting currents flowing in the MgB 2 bulks were intergrain (transport) currents and intragrain currents were negligibly small. The high-pressure sintered sample with smaller grain size showed smaller field dependence of Jc and higher Birr than the conventionally sintered sample with larger grain size. This behavior can be explained by the grain boundary flux pinning.

  17. Effects on magnetic reconnection of a density asymmetry across the current sheet

    Directory of Open Access Journals (Sweden)

    K. G. Tanaka

    2008-08-01

    Full Text Available The magnetopause (MP reconnection is characterized by a density asymmetry across the current sheet. The asymmetry is expected to produce characteristic features in the reconnection layer. Here we present a comparison between the Cluster MP crossing reported by Retinò et al. (2006 and virtual observations in two-dimensional particle-in-cell simulation results. The simulation, which includes the density asymmetry but has zero guide field in the initial condition, has reproduced well the observed features as follows: (1 The prominent density dip region is detected at the separatrix region (SR on the magnetospheric (MSP side of the MP. (2 The intense electric field normal to the MP is pointing to the center of the MP at the location where the density dip is detected. (3 The ion bulk outflow due to the magnetic reconnection is seen to be biased towards the MSP side. (4 The out-of-plane magnetic field (the Hall magnetic field has bipolar rather than quadrupolar structure, the latter of which is seen for a density symmetric case. The simulation also showed rich electron dynamics (formation of field-aligned beams in the proximity of the separatrices, which was not fully resolved in the observations. Stepping beyond the simulation-observation comparison, we have also analyzed the electron acceleration and the field line structure in the simulation results. It is found that the bipolar Hall magnetic field structure is produced by the substantial drift of the reconnected field lines at the MSP SR due to the enhanced normal electric field. The field-aligned electrons at the same MSP SR are identified as the gun smokes of the electron acceleration in the close proximity of the X-line. We have also analyzed the X-line structure obtained in the simulation to find that the density asymmetry leads to a steep density gradient in the in-flow region, which may lead to a non-stationary behavior of the X-line when three-dimensional freedom is taken into account.

  18. Scanning Hall-probe microscopy system for two-dimensional imaging of critical current density in RE-123 coated conductors

    Energy Technology Data Exchange (ETDEWEB)

    Higashikawa, K., E-mail: kohei@super.ees.kyushu-u.ac.jp [Department of Electrical Engineering, Graduate School of Information Science and Electrical Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); Inoue, M.; Kawaguchi, T.; Shiohara, K.; Imamura, K.; Kiss, T. [Department of Electrical Engineering, Graduate School of Information Science and Electrical Engineering, Kyushu University, 744 Motooka, Nishi-ku, Fukuoka 819-0395 (Japan); Iijima, Y.; Kakimoto, K.; Saitoh, T. [Material Technology Laboratory, Fujikura, 1-5-1, Kiba, Koto-ku, Tokyo 135-8512 (Japan); Izumi, T. [Superconductivity Research Laboratory, International Superconductivity Technology Center, 1-10-13 Shinonome, Koto-ku, Tokyo 135-0062 (Japan)

    2011-11-15

    Nondestructive characterization method of in-plane distribution of critical current density for coated conductors. Current distribution in a coated conductor compared with that from theoretical analysis. Relationship between local critical current density and local magnetic field. We have developed a characterization method for two-dimensional imaging of critical current density in coated conductors (CCs) based on scanning Hall-probe microscopy (SHPM). The distributions of the magnetic field around a sample were measured for several different conditions of external magnetic fields, and then were converted to those of the sheet current density which flowed to shield the external magnetic field or to trap the penetrated magnetic field. As a result, it was found that the amplitude of the sheet current density corresponded to that of critical current density almost in all the area of the sample except for the region where current direction changed. This indicates that we could obtain an in-plane distribution of the critical current density with a spatial resolution of around 100 {mu}m in non-destructive manner by this method. We believe that this measurement will be a multifunctional and comprehensive characterization method for coated conductors.

  19. Basic Characteristics of New Developed Higher-Voltage Direct-Current Power-Feeding Prototype System

    Science.gov (United States)

    Babasaki, Tadatoshi; Tanaka, Toshimitsu; Tanaka, Toru; Nozaki, Yousuke; Aoki, Tadahito; Kurokawa, Fujio

    High efficiency power feeding systems are effective solutions for reducing the ICT power consumption with reducing power consumption of the ICT equipment and cooling systems. A higher voltage direct current (HVDC) power feeding system prototype was produced. This system is composed of a rectifier equipment, power distribution unit, batteries, and the ICT equipment. The configuration is similar to a -48V DC power supply system. The output of the rectifier equipment is 100kW, and the output voltage is 401.4V. This paper present the configuration of the HVDC power feeding system and discuss its basic characteristics in the prototype system.

  20. First test of BNL electron beam ion source with high current density electron beam

    Science.gov (United States)

    Pikin, Alexander; Alessi, James G.; Beebe, Edward N.; Shornikov, Andrey; Mertzig, Robert; Wenander, Fredrik; Scrivens, Richard

    2015-01-01

    A new electron gun with electrostatic compression has been installed at the Electron Beam Ion Source (EBIS) Test Stand at BNL. This is a collaborative effort by BNL and CERN teams with a common goal to study an EBIS with electron beam current up to 10 A, current density up to 10,000 A/cm2 and energy more than 50 keV. Intensive and pure beams of heavy highly charged ions with mass-to-charge ratio heavy ion research facilities including NASA Space Radiation Laboratory (NSRL) at BNL and HIE-ISOLDE at CERN. With a multiampere electron gun, the EBIS should be capable of delivering highly charged ions for both RHIC facility applications at BNL and for ISOLDE experiments at CERN. Details of the electron gun simulations and design, and the Test EBIS electrostatic and magnetostatic structures with the new electron gun are presented. The experimental results of the electron beam transmission are given.

  1. Growth and characterization of high current density, high-speed InAs/AlSb resonant tunneling diodes

    Science.gov (United States)

    Soderstrom, J. R.; Brown, E. R.; Parker, C. D.; Mahoney, L. J.; Yao, J. Y.

    1991-01-01

    InAs/AlSb double-barrier resonant tunneling diodes with peak current densities up to 370,000 A/sq cm and high peak-to-valley current ratios of 3.2 at room temperature have been fabricated. The peak current density is well-explained by a stationary-state transport model with the two-band envelope function approximation. The valley current density predicted by this model is less than the experimental value by a factor that is typical of the discrepancy found in other double-barrier structures. It is concluded that threading dislocations are largely inactive in the resonant tunneling process.

  2. Frequency spectra from current vs. magnetic flux density measurements for mobile phones and other electrical appliances.

    Science.gov (United States)

    Straume, Aksel; Johnsson, Anders; Oftedal, Gunnhild; Wilén, Jonna

    2007-10-01

    The frequency spectra of electromagnetic fields have to be determined to evaluate human exposure in accordance to ICNIRP guidelines. In the literature, comparisons with magnetic field guidelines have been performed by using the frequency distribution of the current drawn from the battery. In the present study we compared the frequency spectrum in the range 217 Hz to 2.4 kHz of the magnetic flux density measured near the surface of a mobile phone with the frequency spectrum of the supply current. By using the multiple frequency rule, recommended in the ICNIRP guidelines, we estimated the magnetic field exposure in the two cases. Similar measurements and estimations were done for an electric drill, a hair dryer, and a fluorescent desk lamp. All the devices have a basic frequency of 50 Hz, and the frequency spectra were evaluated up to 550 Hz. We also mapped the magnetic field in 3D around three mobile phones. The frequency distributions obtained from the two measurement methods are not equal. The frequency content of the current leads to an overestimation of the magnetic field exposure by a factor up to 2.2 for the mobile phone. For the drill, the hair dryer, and the fluorescent lamp, the supply current signal underestimated the exposure by a factor up to 2.3. In conclusion, an accurate exposure evaluation requires the magnetic flux density spectrum of the device to be measured directly. There was no indication that the devices studied would exceed the reference levels at the working distances normally used.

  3. Rhizosphere bacteria from sites with higher fungal densities exhibit greater levels of potential antifungal properties

    NARCIS (Netherlands)

    De Boer, W.; De Ridder-Duine, A.S.; Klein Gunnewiek, P.J.A.; Smant, W.; Van Veen, J.A.

    2008-01-01

    A field study was performed to examine whether an increased density of saprotrophic fungi in the rhizosphere selects for bacteria with traits advantageous to living in a fungal-rich environment. Fast-growing bacteria were isolated from the rhizosphere of Carex arenaria (sand sedge) plants growing in

  4. REM sleep behaviour disorder is associated with lower fast and higher slow sleep spindle densities.

    Science.gov (United States)

    O'Reilly, Christian; Godin, Isabelle; Montplaisir, Jacques; Nielsen, Tore

    2015-12-01

    To investigate differences in sleep spindle properties and scalp topography between patients with rapid eye movement sleep behaviour disorder (RBD) and healthy controls, whole-night polysomnograms of 35 patients diagnosed with RBD and 35 healthy control subjects matched for age and sex were compared. Recordings included a 19-lead 10-20 electroencephalogram montage and standard electromyogram, electrooculogram, electrocardiogram and respiratory leads. Sleep spindles were automatically detected using a standard algorithm, and their characteristics (amplitude, duration, density, frequency and frequency slope) compared between groups. Topological analyses of group-discriminative features were conducted. Sleep spindles occurred at a significantly (e.g. t34 = -4.49; P = 0.00008 for C3) lower density (spindles ∙ min(-1) ) for RBD (mean ± SD: 1.61 ± 0.56 for C3) than for control (2.19 ± 0.61 for C3) participants. However, when distinguishing slow and fast spindles using thresholds individually adapted to the electroencephalogram spectrum of each participant, densities smaller (31-96%) for fast but larger (20-120%) for slow spindles were observed in RBD in all derivations. Maximal differences were in more posterior regions for slow spindles, but over the entire scalp for fast spindles. Results suggest that the density of sleep spindles is altered in patients with RBD and should therefore be investigated as a potential marker of future neurodegeneration in these patients.

  5. Higher-Order Adaptive Finite-Element Methods for Kohn-Sham Density Functional Theory

    Science.gov (United States)

    2012-07-03

    equation (25)). The constants c1 and c2 which correspond to the scaling and shifting are determined such that the unwanted eigen-spectrum is mapped into...U. Gross, A. Rubio, Octopus : A tool for the application of time- dependent density functional theory, Phys. Status Solidi B 243 (2006) 24652488. [12

  6. Truncation planes from a dilute pyroclastic density current: field data and analogue experiments.

    Science.gov (United States)

    Douillet, Guilhem Amin; Gegg, Lukas; Mato, Celia; Kueppers, Ulrich; Dingwell, Donald B.

    2016-04-01

    Pyroclastic density currents (PDCs) are a catastrophic transport mode of ground hugging gas-particle mixtures associated with explosive volcanic eruptions. The extremely high sedimentation rates and turbulence levels of these particulate density currents can freeze and preserve dynamic phenomena that happen but are not recorded in other sedimentary environments. Several intriguing and unanticipated features have been identified in outcrops and reproduced via analogue experiments, with the potential to change our views on morphodynamics and particle motion. Three types of small-scale (ca. 10 cm) erosion structures were observed on the stoss side of dune bedforms in the field: 1) vertical erosion planes covered with stoss-aggrading, vertical lamination, 2) overturned laminations at the preserved limit of erosion planes and 3) loss of stratification at erosion planes. These features are interpreted to indicate rapidly evolving velocities, undeveloped boundary layers, and a diffuse zone rather than a sharp border defining the flow-bed interface. Most experimental work on particle motion and erosion from the literature has been accomplished under constant conditions and with planar particle beds. Here, in order to reproduce the field observations, short-lived air-jets generated with a compressor-gun were shot into stratified beds of coarse particles (300 μm) of low density (1000 kg/m3). These "eroding jets" were filmed with a high speed camera and the deposits were sectioned after the experiments. The three natural types of erosion characteristics were experimentally generated. Vertical erosion planes are produced by small-scale, relatively sustained jets. Overturned laminations are due to a fluidization-like behavior at the erosion front of short-lived, strong jets, demonstrating that the fluid's velocity profile penetrates into the deposit. Loss of lamination seems related to the nature of erosion onset in packages. Rather than providing simple answers, the dataset

  7. Classification of motor imagery by means of cortical current density estimation and Von Neumann entropy.

    Science.gov (United States)

    Kamousi, Baharan; Amini, Ali Nasiri; He, Bin

    2007-06-01

    The goal of the present study is to employ the source imaging methods such as cortical current density estimation for the classification of left- and right-hand motor imagery tasks, which may be used for brain-computer interface (BCI) applications. The scalp recorded EEG was first preprocessed by surface Laplacian filtering, time-frequency filtering, noise normalization and independent component analysis. Then the cortical imaging technique was used to solve the EEG inverse problem. Cortical current density distributions of left and right trials were classified from each other by exploiting the concept of Von Neumann entropy. The proposed method was tested on three human subjects (180 trials each) and a maximum accuracy of 91.5% and an average accuracy of 88% were obtained. The present results confirm the hypothesis that source analysis methods may improve accuracy for classification of motor imagery tasks. The present promising results using source analysis for classification of motor imagery enhances our ability of performing source analysis from single trial EEG data recorded on the scalp, and may have applications to improved BCI systems.

  8. Reconstructing cortical current density by exploring sparseness in the transform domain.

    Science.gov (United States)

    Ding, Lei

    2009-05-07

    In the present study, we have developed a novel electromagnetic source imaging approach to reconstruct extended cortical sources by means of cortical current density (CCD) modeling and a novel EEG imaging algorithm which explores sparseness in cortical source representations through the use of L1-norm in objective functions. The new sparse cortical current density (SCCD) imaging algorithm is unique since it reconstructs cortical sources by attaining sparseness in a transform domain (the variation map of cortical source distributions). While large variations are expected to occur along boundaries (sparseness) between active and inactive cortical regions, cortical sources can be reconstructed and their spatial extents can be estimated by locating these boundaries. We studied the SCCD algorithm using numerous simulations to investigate its capability in reconstructing cortical sources with different extents and in reconstructing multiple cortical sources with different extent contrasts. The SCCD algorithm was compared with two L2-norm solutions, i.e. weighted minimum norm estimate (wMNE) and cortical LORETA. Our simulation data from the comparison study show that the proposed sparse source imaging algorithm is able to accurately and efficiently recover extended cortical sources and is promising to provide high-accuracy estimation of cortical source extents.

  9. Reduced event-related current density in the anterior cingulate cortex in schizophrenia.

    Science.gov (United States)

    Mulert, C; Gallinat, J; Pascual-Marqui, R; Dorn, H; Frick, K; Schlattmann, P; Mientus, S; Herrmann, W M; Winterer, G

    2001-04-01

    There is good evidence from neuroanatomic postmortem and functional imaging studies that dysfunction of the anterior cingulate cortex plays a prominent role in the pathophysiology of schizophrenia. So far, no electrophysiological localization study has been performed to investigate this deficit. We investigated 18 drug-free schizophrenic patients and 25 normal subjects with an auditory choice reaction task and measured event-related activity with 19 electrodes. Estimation of the current source density distribution in Talairach space was performed with low-resolution electromagnetic tomography (LORETA). In normals, we could differentiate between an early event-related potential peak of the N1 (90-100 ms) and a later N1 peak (120-130 ms). Subsequent current-density LORETA analysis in Talairach space showed increased activity in the auditory cortex area during the first N1 peak and increased activity in the anterior cingulate gyrus during the second N1 peak. No activation difference was observed in the auditory cortex between normals and patients with schizophrenia. However, schizophrenics showed significantly less anterior cingulate gyrus activation and slowed reaction times. Our results confirm previous findings of an electrical source in the anterior cingulate and an anterior cingulate dysfunction in schizophrenics. Our data also suggest that anterior cingulate function in schizophrenics is disturbed at a relatively early time point in the information-processing stream (100-140 ms poststimulus).

  10. Current density distribution mapping in PEM fuel cells as an instrument for operational measurements

    Energy Technology Data Exchange (ETDEWEB)

    Geske, M.; Heuer, M.; Heideck, G.; Styczynski, Z. A. [Otto-von-Guericke University Magdeburg, Chair Electric Power Networks and Renewable Energy Sources, Magdeburg (Germany)

    2010-07-01

    A newly developed measurement system for current density distribution mapping has enabled a new approach for operational measurements in proton exchange membrane fuel cells (PEMFC). Taking into account previously constructed measurement systems, a method based on a multi layer printed circuit board was chosen for the development of the new system. This type of system consists of a sensor, a special electronic device and the control and visualization PC. For the acquisition of the current density distribution values, a sensor device was designed and installed within a multilayer printed circuit board with integrated shunt resistors. Varying shunt values can be taken into consideration with a newly developed and evaluated calibration method. The sensor device was integrated in a PEM fuel cell stack to prove the functionality of the whole measurement system. A software application was implemented to visualize and save the measurement values. Its functionality was verified by operational measurements within a PEMFC system. Measurement accuracy and possible negative reactions of the sensor device during PEMFC operation are discussed in detail in this paper. The developed system enables operational measurements for different operating phases of PEM fuel cells. Additionally, this can be seen as a basis for new opportunities of optimization for fuel cell design and operation modes. (author)

  11. Evaluation of ion current density distribution on an extraction electrode of a radio frequency ion thruster

    Science.gov (United States)

    Masherov, P.; Riaby, V.; Abgaryan, V.

    2017-01-01

    The radial distributions of ion current density on an ion extracting electrode of a radio frequency (RF) ion thruster (RIT) with an inductive plasma source were obtained using probe diagnostics of the RF xenon plasma. Measurements were carried out using a plane wall probe simulator and the VGPS-12 Probe System of Plasma Sensors Co. At xenon flow rate q  =  2 sccm plasma pressure was 2 · 10-3 Torr, incident RF generator power varied in the range P g  =  50-250 W with RF power absorbed by plasma up to P p  =  220 W. Ion current densities were determined using semi- and double-logarithmic probe characteristics by linear extrapolations of their ion branches to probe floating potentials. The same parameters were also measured in undisturbed plasma by a classic cylindrical probe. They exceeded plane probe data by more than two times, showing the effectiveness of plasma sheath reproduction of the RIT ion extracting electrode by the plane wall probe simulator. Slight non-uniformity of the resulting plasma distributions and simplified RIT model design showed that the studied device with flat antenna coil and ferrite core could be considered as a promising prospect for RITs of new generation.

  12. Seasonal Variation in Sea Turtle Density and Abundance in the Southeast Florida Current and Surrounding Waters.

    Science.gov (United States)

    Bovery, Caitlin M; Wyneken, Jeanette

    2015-01-01

    Assessment and management of sea turtle populations is often limited by a lack of available data pertaining to at-sea distributions at appropriate spatial and temporal resolutions. Assessing the spatial and temporal distributions of marine turtles in an open system poses both observational and analytical challenges due to the turtles' highly migratory nature. Surface counts of marine turtles in waters along the southern part of Florida's east coast were made in and adjacent to the southeast portion of the Florida Current using standard aerial surveys during 2011 and 2012 to assess their seasonal presence. This area is of particular concern for sea turtles as interest increases in offshore energy developments, specifically harnessing the power of the Florida Current. While it is understood that marine turtles use these waters, here we evaluate seasonal variation in sea turtle abundance and density over two years. Density of sea turtles observed within the study area ranged from 0.003 turtles km-2 in the winter of 2011 to 0.064 turtles km-2 in the spring of 2012. This assessment of marine turtles in the waters off southeast Florida quantifies their in-water abundance across seasons in this area to establish baselines and inform future management strategies of these protected species.

  13. Seasonal Variation in Sea Turtle Density and Abundance in the Southeast Florida Current and Surrounding Waters

    Science.gov (United States)

    Bovery, Caitlin M.; Wyneken, Jeanette

    2015-01-01

    Assessment and management of sea turtle populations is often limited by a lack of available data pertaining to at-sea distributions at appropriate spatial and temporal resolutions. Assessing the spatial and temporal distributions of marine turtles in an open system poses both observational and analytical challenges due to the turtles’ highly migratory nature. Surface counts of marine turtles in waters along the southern part of Florida’s east coast were made in and adjacent to the southeast portion of the Florida Current using standard aerial surveys during 2011 and 2012 to assess their seasonal presence. This area is of particular concern for sea turtles as interest increases in offshore energy developments, specifically harnessing the power of the Florida Current. While it is understood that marine turtles use these waters, here we evaluate seasonal variation in sea turtle abundance and density over two years. Density of sea turtles observed within the study area ranged from 0.003 turtles km-2 in the winter of 2011 to 0.064 turtles km-2 in the spring of 2012. This assessment of marine turtles in the waters off southeast Florida quantifies their in-water abundance across seasons in this area to establish baselines and inform future management strategies of these protected species. PMID:26717520

  14. Critical current density measurement of thin films by AC susceptibility based on the penetration parameter h

    Energy Technology Data Exchange (ETDEWEB)

    Li Xiaofen, E-mail: xiaofenli@gmail.com [Materials Research Division, Riso National Laboratory for Sustainable Energy, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Grivel, Jean-Claude; Abrahamsen, Asger B.; Andersen, Niels H. [Materials Research Division, Riso National Laboratory for Sustainable Energy, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark)

    2012-07-15

    We have numerically proved that the dependence of AC susceptibility {chi} of a E(J) power law superconducting thin disc on many parameters can be reduced to one penetration parameter h, with E the electric field and J the current density. Based on this result, we propose a way of measuring the critical current density J{sub c} of superconducting thin films by AC susceptibility. Compared with the normally used method based on the peak of the imaginary part, our method uses a much larger range of the AC susceptibility curve, thus allowing determination of the temperature (T) dependence of J{sub c} from a normally applied {chi}(T) measurement. A fitting equation J{sub c} = 1.9H{sub a} Divides {chi} Prime Divides {sup 0.69}/d, -0.4 < {chi} Prime < -0.001 derived from the critical state case (Bean model) can be used in most situations, where H{sub a} is the amplitude of the applied AC field, {chi} Prime is the real part of the normalized susceptibility and d is the thickness of the film. The method is valid for the cases where the film is fully penetrated. We also discuss how the finite London penetration depth affects the susceptibility when the film is screened. Measurements with varying T, H{sub a} and DC background field H{sub dc} are performed to support the arguments.

  15. Critical current density measurement of thin films by AC susceptibility based on the penetration parameter h

    Science.gov (United States)

    Li, Xiao-Fen; Grivel, Jean-Claude; Abrahamsen, Asger B.; Andersen, Niels H.

    2012-07-01

    We have numerically proved that the dependence of AC susceptibility χ of a E(J) power law superconducting thin disc on many parameters can be reduced to one penetration parameter h, with E the electric field and J the current density. Based on this result, we propose a way of measuring the critical current density Jc of superconducting thin films by AC susceptibility. Compared with the normally used method based on the peak of the imaginary part, our method uses a much larger range of the AC susceptibility curve, thus allowing determination of the temperature (T) dependence of Jc from a normally applied χ(T) measurement. A fitting equation Jc = 1.9Ha∣χ‧∣0.69/d, -0.4 Bean model) can be used in most situations, where Ha is the amplitude of the applied AC field, χ‧ is the real part of the normalized susceptibility and d is the thickness of the film. The method is valid for the cases where the film is fully penetrated. We also discuss how the finite London penetration depth affects the susceptibility when the film is screened. Measurements with varying T, Ha and DC background field Hdc are performed to support the arguments.

  16. A new method for estimating the critical current density of a superconductor from its hysteresis loop

    Energy Technology Data Exchange (ETDEWEB)

    Lal, Ratan, E-mail: rlal_npl_3543@yahoo.i [Superconductivity Division, National Physical Laboratory, Council of Scientific and Industrial Research, Dr. K.S. Krishnan Road, New Delhi 110012 (India)

    2010-02-15

    The critical current density J{sub c} of some of the superconducting samples, calculated on the basis of the Bean's model, shows negative curvature for low magnetic field with a downward bending near H = 0. To avoid this problem Kim's expression of the critical current density, J{sub c} = k/(H{sub 0} + H), where J{sub c} has positive curvature for all H, has been employed by connecting the positive constants k and H{sub 0} with the features of the hysteresis loop of a superconductor. A relation between the full penetration field H{sub p} and the magnetic field H{sub min}, at which the magnetization is minimum, is obtained from the Kim's theory. Taking the value of J{sub c} at H = H{sub p} according to the actual loop width, as in the Bean's theory, and at H = 0 according to an enhanced loop width due to the local internal field, values of k and H{sub 0} are obtained in terms of the magnetization values M{sup +}(-H{sub min}), M{sup -}(H{sub min}), M{sup +}(H{sub p}) and M{sup -}(H{sub p}). The resulting method of estimating J{sub c} from the hysteresis loop turns out to be as simple as the Bean's method.

  17. Current Density Distribution Mapping in PEM Fuel Cells as An Instrument for Operational Measurements

    Directory of Open Access Journals (Sweden)

    Martin Geske

    2010-04-01

    Full Text Available A newly developed measurement system for current density distribution mapping has enabled a new approach for operational measurements in proton exchange membrane fuel cells (PEMFC. Taking into account previously constructed measurement systems, a method based on a multi layer printed circuit board was chosen for the development of the new system. This type of system consists of a sensor, a special electronic device and the control and visualization PC. For the acquisition of the current density distribution values, a sensor device was designed and installed within a multilayer printed circuit board with integrated shunt resistors. Varying shunt values can be taken into consideration with a newly developed and evaluated calibration method. The sensor device was integrated in a PEM fuel cell stack to prove the functionality of the whole measurement system. A software application was implemented to visualize and save the measurement values. Its functionality was verified by operational measurements within a PEMFC system. Measurement accuracy and possible negative reactions of the sensor device during PEMFC operation are discussed in detail in this paper. The developed system enables operational measurements for different operating phases of PEM fuel cells. Additionally, this can be seen as a basis for new opportunities of optimization for fuel cell design and operation modes.

  18. Spatially resolved determination of the short-circuit current density of silicon solar cells via lock-in thermography

    Energy Technology Data Exchange (ETDEWEB)

    Fertig, Fabian, E-mail: fabian.fertig@ise.fraunhofer.de; Greulich, Johannes; Rein, Stefan [Fraunhofer Institute for Solar Energy Systems ISE, Heidenhofstr. 2, D-79110 Freiburg (Germany)

    2014-05-19

    We present a spatially resolved method to determine the short-circuit current density of crystalline silicon solar cells by means of lock-in thermography. The method utilizes the property of crystalline silicon solar cells that the short-circuit current does not differ significantly from the illuminated current under moderate reverse bias. Since lock-in thermography images locally dissipated power density, this information is exploited to extract values of spatially resolved current density under short-circuit conditions. In order to obtain an accurate result, one or two illuminated lock-in thermography images and one dark lock-in thermography image need to be recorded. The method can be simplified in a way that only one image is required to generate a meaningful short-circuit current density map. The proposed method is theoretically motivated, and experimentally validated for monochromatic illumination in comparison to the reference method of light-beam induced current.

  19. Determination of Defect Densities in High Electron Mobility Transistors Using Current Transient DLTS

    Science.gov (United States)

    Palma, John; Mil'shtein, Samson

    2011-12-01

    Since its introduction, Deep Level Transient Spectroscopy (DLTS) has become the preferred tool for investigating semiconductor defects. The limitations of measuring the small changes in gate capacitance in transistors led to the advent of current transient DLTS where the defects manifest themselves as a small change in drain current. However, this method was introduced at a time when heterostructure devices, such as High Electron Mobility Transistors (HEMTs), were non-existent and fails in determining defect concentrations in these modern devices. This study establishes a method by which defect concentrations can be determined in HEMT structures using current transient DLTS. First, the relationship between the change in the trap charge and the transistor drain current is established. Then, a computer aided technique is described which determines the volume within the device where the Fermi level crosses the trap energy. The result is that trap densities and their locations can be determined. DLTS measurements revealed two traps with ET = 0.43 and Nt = 1.1×1017cm-3, and ET = 0.19 and Nt = 3.1×1017 cm-3 for a tested HEMT.

  20. Modeling space-charge-limited currents in organic semiconductors: Extracting trap density and mobility

    KAUST Repository

    Dacuña, Javier

    2011-11-28

    We have developed and have applied a mobility edge model that takes drift and diffusion currents to characterize the space-charge-limited current in organic semiconductors into account. The numerical solution of the drift-diffusion equation allows the utilization of asymmetric contacts to describe the built-in potential within the device. The model has been applied to extract information of the distribution of traps from experimental current-voltage measurements of a rubrene single crystal from Krellner showing excellent agreement across several orders of magnitude in the current. Although the two contacts are made of the same metal, an energy offset of 580 meV between them, ascribed to differences in the deposition techniques (lamination vs evaporation) was essential to correctly interpret the shape of the current-voltage characteristics at low voltage. A band mobility of 0.13cm 2V-1s-1 for holes is estimated, which is consistent with transport along the long axis of the orthorhombic unit cell. The total density of traps deeper than 0.1 eV was 2.2×1016cm -3. The sensitivity analysis and error estimation in the obtained parameters show that it is not possible to accurately resolve the shape of the trap distribution for energies deeper than 0.3 eV or shallower than 0.1 eV above the valence-band edge. The total number of traps deeper than 0.3 eV, however, can be estimated. Contact asymmetry and the diffusion component of the current play an important role in the description of the device at low bias and are required to obtain reliable information about the distribution of deep traps. © 2011 American Physical Society.

  1. Obesity-related eating behaviors are associated with higher food energy density and higher consumption of sugary and alcoholic beverages: a cross-sectional study.

    Science.gov (United States)

    Muñoz-Pareja, Maritza; Guallar-Castillón, Pilar; Mesas, Arthur E; López-García, Esther; Rodríguez-Artalejo, Fernando

    2013-01-01

    Obesity-related eating behaviors (OREB) are associated with higher energy intake. Total energy intake can be decomposed into the following constituents: food portion size, food energy density, the number of eating occasions, and the energy intake from energy-rich beverages. To our knowledge this is the first study to examine the association between the OREB and these energy components. Data were taken from a cross-sectional study conducted in 2008-2010 among 11,546 individuals representative of the Spanish population aged ≥ 18 years. Information was obtained on the following 8 self-reported OREB: not planning how much to eat before sitting down, eating precooked/canned food or snacks bought at vending machines or at fast-food restaurants, not choosing low-energy foods, not removing visible fat from meat or skin from chicken, and eating while watching TV. Usual diet was assessed with a validated diet history. Analyses were performed with linear regression with adjustment for main confounders. Compared to individuals with ≤ 1 OREB, those with ≥ 5 OREB had a higher food energy density (β 0.10; 95% CI 0.08, 0.12 kcal/g/day; p-trendintake of dairy products and red meat, and with lower consumption of fresh fruit, oily fish and white meat. No association was found between the number of OREB and food portion size or the number of eating occasions. OREB were associated with higher food energy density and higher consumption of sugary and alcoholic beverages. Avoiding OREB may prove difficult because they are firmly socially rooted, but these results may nevertheless serve to palliate the undesirable effects of OREB by reducing the associated energy intake.

  2. Improved critical current density of MgB2--carbon nanotubes composite.

    Science.gov (United States)

    Shekhar, Chandra; Giri, Rajiv; Malik, S K; Srivastav, O N

    2007-06-01

    In the present study, we report a systematic study of doping/admixing of carbon nanotubes (CNTs) in different concentrations in MgB2. The composite material corresponding to MgB2-x at.% CNTs (35 at.% > or = x > or = 0 at.%) have been prepared by solid-state reaction at ambient pressure. All the samples in the present investigation have been subjected to structural/microstructural characterization employing XRD, Scanning electron microscopic (SEM), and Transmission electron microscopic (TEM) techniques. The magnetization measurements were performed by Physical property measurement system (PPMS) and electrical transport measurements have been done by the four-probe technique. The microstructural investigations reveal the formation of MgB2-carbon nanotube composites. A CNT connecting the MgB2 grains may enhance critical current density due to its size (approximately 5-20 nm diameter) compatible with coherence length of MgB2 (approximately 5-6 nm) and ballistic transport current carrying capability along the tube axis. The transport critical current density (Jct) of MgB2 samples with varying CNTs concentration have been found to vary significantly e.g., Jct of the MgB2 sample with 10 at.% CNT addition is approximately 2.3 x 10(3) A/cm2 and its value for MgB2 sample without CNT addition is approximately 7.2 x 102 A/cm2 at 20 K. In order to study the flux pinning effect of CNTs doping/ admixing in MgB2, the evaluation of intragrain critical current density (JJ) has been carried out through magnetic measurements on the fine powdered version of the as synthesized samples. The optimum result on Jc is obtained for 10 at.% CNTs admixed MgB2 sample at 5 K, the Jc reaches approximately 5.2 x 10(6) A/cm2 in self field, -1.6 x 10(6) A/cm2 at 1 T, approximately 2.9 x 10(5) A/cm2 at 2.6 T, and approximately 3.9 x 10(4) A/cm2 at 4 T. The high value of intragrain Jc in 10 at.% CNTs admixed MgB2 superconductor has been attributed to the incorporation of CNTs into the crystal matrix of

  3. Higher order classical density functional theory for branched chains and rings.

    Science.gov (United States)

    Marshall, Bennett D; Chapman, Walter G

    2011-12-22

    We develop a general density functional theory for polyatomic molecules by taking the complete association limit of Wertheim's thermodynamic perturbation theory in a general way. By enforcing the complete association limit at an early point in the derivation and introducing the concept of molecular graphs, a general form for the free energy functional and segment densities are developed for both rigid and semiflexible molecules. The theory is applicable to branched chains, rings, or any other molecular structure. As an example the theory is applied as a second order perturbation theory to the case of molecules with a rigid three segment head and a fully flexible tail in a slit pore where bond angle of the rigid portion is an independent variable.

  4. Finite Temperature and Density Effects in Higher Dimensions with and without Compactifications

    CERN Document Server

    Shiraishi, Kiyoshi

    2012-01-01

    Expressions for the thermodynamic potential of a Dirac fermion gas are represented at finite temperature with the chemical potential in an ultrastatic space $R^d\\times S^N$. The high- and low- temperature expansions for the thermodynamic potential are obtained and, in particular, strongly degenerate fermi gas is investigated. For the Candelas-Weinberg model, sufficiently high "charge" density prevents the compactification of the extra space.

  5. Current status of educational services in higher agricultural education in Ukraine

    Directory of Open Access Journals (Sweden)

    A. S. Cobets’

    2016-07-01

    Full Text Available Perspective directions of integration state policy of Ukraine Higher Education  into the European educational space and steps of implementation are determined. It is analysed the current state of higher agricultural education and integration current state policy of Ukraine Higher Education into the European educational space which allowed to identify problems and highlighted areas for further development. It is considered that it is necessary to establish cooperation in the triangle «production ­ education – science», extend the impact of scientists and experts on the content of  educational sector, come educational standards to needs and challenges of the real economy, as upgrades of industry standards for higher education, forming curricula, new teaching methods. Professionals training is possible only in a simulation of modern production principles, including the European Union. It is necessary to strengthen the position of agricultural universities as international educational and scientific centers in the framework of the European educational space. This refers to the practice and teaching students abroad, teachers training, participation in international programs, joint research. Ukrainian agricultural education system has competitive advantages despite the general neglect and can be considered unique in the educational market, it has conditions for the creation and testing of innovative products for different agro­climatic zones within a region. This provides the results of knowledge­based real conditions of agricultural production. Among the weaknesses of the education system it is possible to note a lack of cooperation with employers, lack of logistical and information and communication resources, mismatch of modern innovative designs and high technologies. It is therefore necessary to overcome the gap between the content of education and the real needs of innovation economy. In general, you need to ensure long­term practice

  6. High short-circuit current density CdTe solar cells using all-electrodeposited semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Echendu, O.K., E-mail: oechendu@yahoo.com; Fauzi, F.; Weerasinghe, A.R.; Dharmadasa, I.M.

    2014-04-01

    CdS/CdTe and ZnS/CdTe n–n heterojunction solar cells have been fabricated using all-electrodeposited semiconductors. The best devices show remarkable high short-circuit current densities of 38.5 mAcm{sup −2} and 47.8 mAcm{sup −2}, open-circuit voltages of 630 mV and 646 mV and conversion efficiencies of 8.0% and 12.0% respectively. The major strength of these device structures lies in the combination of n–n heterojunction with a large Schottky barrier at the n-CdTe/metal back contact which provides the required band bending for the separation of photo-generated charge carriers. This is in addition to the use of a high quality n-type CdTe absorber layer with high electron mobility. The potential barrier heights estimated for these devices from the current–voltage characteristics exceed 1.09 eV and 1.13 eV for CdS/CdTe and ZnS/CdTe cells respectively. The diode rectification factors of both devices are in excess of four orders of magnitude with reverse saturation current densities of 1.0 × 10{sup −7} Acm{sup −2} and 4.0 × 10{sup −7} Acm{sup −2} respectively. These all-electrodeposited solar cell device structures are currently being studied and developed as an alternative to the well-known p–n junction structures which utilise chemical bath-deposited CdS. The preliminary material growth, device fabrication and assessment results are presented in this paper. - Highlights: • Two-electrode deposition. • High J{sub sc} Schottky barrier solar cells. • CdCl{sub 2} + CdF{sub 2} treatment.

  7. Ion Current Density Study of the NASA-300M and NASA-457Mv2 Hall Thrusters

    Science.gov (United States)

    Huang, Wensheng; Shastry, Rohit; Herman, Daniel A.; Soulas, George C.; Kamhawi, Hani

    2012-01-01

    NASA Glenn Research Center is developing a Hall thruster in the 15-50 kW range to support future NASA missions. As a part of the process, the performance and plume characteristics of the NASA-300M, a 20-kW Hall thruster, and the NASA-457Mv2, a 50-kW Hall thruster, were evaluated. The collected data will be used to improve the fidelity of the JPL modeling tool, Hall2De, which will then be used to aid the design of the 15-50 kW Hall thruster. This paper gives a detailed overview of the Faraday probe portion of the plume characterization study. The Faraday probe in this study is a near-field probe swept radially at many axial locations downstream of the thruster exit plane. Threshold-based integration limits with threshold values of 1/e, 1/e(sup 2), and 1/e(sup 3) times the local peak current density are tried for the purpose of ion current integration and divergence angle calculation. The NASA-300M is operated at 7 conditions and the NASA-457Mv2 at 14 conditions. These conditions span discharge voltages of 200 to 500 V and discharge power of 10 to 50 kW. The ion current density profiles of the near-field plume originating from the discharge channel are discovered to strongly resemble Gaussian distributions. A novel analysis approach involving a form of ray tracing is used to determine an effective point of origin for the near-field plume. In the process of performing this analysis, definitive evidence is discovered that showed the near-field plume is bending towards the thruster centerline.

  8. Obesity-related eating behaviors are associated with higher food energy density and higher consumption of sugary and alcoholic beverages: a cross-sectional study.

    Directory of Open Access Journals (Sweden)

    Maritza Muñoz-Pareja

    Full Text Available OBJECTIVES: Obesity-related eating behaviors (OREB are associated with higher energy intake. Total energy intake can be decomposed into the following constituents: food portion size, food energy density, the number of eating occasions, and the energy intake from energy-rich beverages. To our knowledge this is the first study to examine the association between the OREB and these energy components. METHODS: Data were taken from a cross-sectional study conducted in 2008-2010 among 11,546 individuals representative of the Spanish population aged ≥ 18 years. Information was obtained on the following 8 self-reported OREB: not planning how much to eat before sitting down, eating precooked/canned food or snacks bought at vending machines or at fast-food restaurants, not choosing low-energy foods, not removing visible fat from meat or skin from chicken, and eating while watching TV. Usual diet was assessed with a validated diet history. Analyses were performed with linear regression with adjustment for main confounders. RESULTS: Compared to individuals with ≤ 1 OREB, those with ≥ 5 OREB had a higher food energy density (β 0.10; 95% CI 0.08, 0.12 kcal/g/day; p-trend<0.001 and a higher consumption of sugary drinks (β 7; 95% CI -7, 20 ml/day; p-trend<0.05 and of alcoholic beverages (β 24; 95% CI 10, 38 ml/day; p-trend<0.001. Specifically, a higher number of OREB was associated with higher intake of dairy products and red meat, and with lower consumption of fresh fruit, oily fish and white meat. No association was found between the number of OREB and food portion size or the number of eating occasions. CONCLUSIONS: OREB were associated with higher food energy density and higher consumption of sugary and alcoholic beverages. Avoiding OREB may prove difficult because they are firmly socially rooted, but these results may nevertheless serve to palliate the undesirable effects of OREB by reducing the associated energy intake.

  9. Modelling of the reactive sputtering process with non-uniform discharge current density and different temperature conditions

    Science.gov (United States)

    Vašina, P; Hytková, T; Eliáš, M

    2009-05-01

    The majority of current models of the reactive magnetron sputtering assume a uniform shape of the discharge current density and the same temperature near the target and the substrate. However, in the real experimental set-up, the presence of the magnetic field causes high density plasma to form in front of the cathode in the shape of a toroid. Consequently, the discharge current density is laterally non-uniform. In addition to this, the heating of the background gas by sputtered particles, which is usually referred to as the gas rarefaction, plays an important role. This paper presents an extended model of the reactive magnetron sputtering that assumes the non-uniform discharge current density and which accommodates the gas rarefaction effect. It is devoted mainly to the study of the behaviour of the reactive sputtering rather that to the prediction of the coating properties. Outputs of this model are compared with those that assume uniform discharge current density and uniform temperature profile in the deposition chamber. Particular attention is paid to the modelling of the radial variation of the target composition near transitions from the metallic to the compound mode and vice versa. A study of the target utilization in the metallic and compound mode is performed for two different discharge current density profiles corresponding to typical two pole and multipole magnetics available on the market now. Different shapes of the discharge current density were tested. Finally, hysteresis curves are plotted for various temperature conditions in the reactor.

  10. Plasma Shape and Current Density Profile Control in Advanced Tokamak Operating Scenarios

    Science.gov (United States)

    Shi, Wenyu

    The need for new sources of energy is expected to become a critical problem within the next few decades. Nuclear fusion has sufficient energy density to potentially supply the world population with its increasing energy demands. The tokamak is a magnetic confinement device used to achieve controlled fusion reactions. Experimental fusion technology has now reached a level where tokamaks are able to produce about as much energy as is expended in heating the fusion fuel. The next step towards the realization of a nuclear fusion tokamak power plant is ITER, which will be capable of exploring advanced tokamak (AT) modes, characterized by a high fusion gain and plasma stability. The extreme requirements of the advanced modes motivates researchers to improve the modeling of the plasma response as well as the design of feedback controllers. This dissertation focuses on several magnetic and kinetic control problems, including the plasma current, position and shape control, and data-driven and first-principles-driven modeling and control of plasma current density profile and the normalized plasma pressure ratio betaN. The plasma is confined within the vacuum vessel by an external electromagnetic field, produced primarily by toroidal and poloidal field coils. The outermost closed plasma surface or plasma boundary is referred to as the shape of the plasma. A central characteristic of AT plasma regimes is an extreme elongated shape. The equilibrium among the electromagnetic forces acting on an elongated plasma is unstable. Moreover, the tokamak performance is improved if the plasma is located in close proximity to the torus wall, which guarantees an efficient use of available volume. As a consequence, feedback control of the plasma position and shape is necessary. In this dissertation, an Hinfinity-based, multi-input-multi-output (MIMO) controller for the National Spherical Torus Experiment (NSTX) is developed, which is used to control the plasma position, shape, and X

  11. Direct numerical simulations of particle-laden density currents with adaptive, discontinuous finite elements

    Directory of Open Access Journals (Sweden)

    S. D. Parkinson

    2014-05-01

    Full Text Available High resolution direct numerical simulations (DNS are an important tool for the detailed analysis of turbidity current dynamics. Models that resolve the vertical structure and turbulence of the flow are typically based upon the Navier–Stokes equations. Two-dimensional simulations are known to produce unrealistic cohesive vortices that are not representative of the real three-dimensional physics. The effect of this phenomena is particularly apparent in the later stages of flow propagation. The ideal solution to this problem is to run the simulation in three dimensions but this is computationally expensive. This paper presents a novel finite-element (FE DNS turbidity current model that has been built within Fluidity, an open source, general purpose, computational fluid dynamics code. The model is validated through re-creation of a lock release density current at a Grashof number of 5 × 106 in two, and three-dimensions. Validation of the model considers the flow energy budget, sedimentation rate, head speed, wall normal velocity profiles and the final deposit. Conservation of energy in particular is found to be a good metric for measuring mesh performance in capturing the range of dynamics. FE models scale well over many thousands of processors and do not impose restrictions on domain shape, but they are computationally expensive. Use of discontinuous discretisations and adaptive unstructured meshing technologies, which reduce the required element count by approximately two orders of magnitude, results in high resolution DNS models of turbidity currents at a fraction of the cost of traditional FE models. The benefits of this technique will enable simulation of turbidity currents in complex and large domains where DNS modelling was previously unachievable.

  12. Erosion and entrainment of snow and ice by pyroclastic density currents: some outstanding questions (Invited)

    Science.gov (United States)

    Walder, J. S.

    2010-12-01

    A pyroclastic density current moving over snow is likely to transform to a lahar if the pyroclasts incorporate enough (melting) snow and meltwater to bring the bulk water content of the mixture to about 35% by volume. However, the processes by which such a mixture forms are still not well understood. Walder (Bull. Volcanol., v. 62, 2000) showed experimentally the existence of an erosion mechanism that functions even in the absence of relative shear motion between pyroclasts and snow substrate: a portion of the snow melted by a blanket of pyroclasts is vaporized; the flux of water vapor upward through the pyroclasts may be enough to fluidize the pyroclasts, which then convect, rapidly scour the snow substrate and transform into a slurry. But these experiments do not tell us how moving pyroclasts would erode snow, and simply releasing a hot grain flow over a snow surface in the lab gives misleading results owing to improper scaling of τ/σ , the ratio of the shear stress τ exerted by the pyroclastic flow to the shear strength σ of snow. There seems to be no way around this problem for experiments with actual snow. However, it may be possible to circumvent the scaling problem by replacing the snow substrate by a gas-fluidized particle bed: by varying the gas flux, the apparent shear strength of the particle bed can be varied. Such an investigation of erosional processes could be done at room temperature. Snow-avalanche studies (for example, Gauer and Issler, Ann. Glaciol. v. 38, 2003) may provide some insight into snow erosion by a pyroclastic density current. Snow is eroded at the base of a dense snow avalanche by abrasion, particle impacts, and—at the avalanche head—by plowing and a “blasting” mechanism associated with compression of the snowpack and expulsion of pore fluid (air). Erosion at the avalanche head seems to be particularly important. Similar processes are likely to occur when the over-riding flow comprises hot grains. The laboratory release of

  13. Distribution characteristics of coronal electric current density as an indicator for the occurrence of a solar flare

    Science.gov (United States)

    Kang, Jihye; Magara, Tetsuya; Inoue, Satoshi; Kubo, Yuki; Nishizuka, Naoto

    2016-10-01

    In this paper we investigate the distribution characteristics of the coronal electric current density in a flare-producing active region (AR12158; SOL2014-09-10) by reconstructing nonlinear force-free (NLFF) fields from photospheric magnetic field data. A time series of NLFF fields shows the spatial distribution and its temporal development of coronal current density in this active region. A fractal dimensional analysis shows that a concentrated coronal current forms a structure of fractal spatiality. Furthermore, the distribution function of coronal current density is featured with a double power-law profile, and the value of electric current density at the breaking point of a double power-law fitting function shows a noticeable time variation toward the onset of an X-class flare. We discuss that this quantity will be a useful indicator for the occurrence of a flare.

  14. Distribution characteristics of coronal electric current density as an indicator for the occurrence of a solar flare

    Science.gov (United States)

    Kang, Jihye; Magara, Tetsuya; Inoue, Satoshi; Kubo, Yuki; Nishizuka, Naoto

    2016-12-01

    In this paper we investigate the distribution characteristics of the coronal electric current density in a flare-producing active region (AR12158; SOL2014-09-10) by reconstructing nonlinear force-free (NLFF) fields from photospheric magnetic field data. A time series of NLFF fields shows the spatial distribution and its temporal development of coronal current density in this active region. A fractal dimensional analysis shows that a concentrated coronal current forms a structure of fractal spatiality. Furthermore, the distribution function of coronal current density is featured with a double power-law profile, and the value of electric current density at the breaking point of a double power-law fitting function shows a noticeable time variation toward the onset of an X-class flare. We discuss that this quantity will be a useful indicator for the occurrence of a flare.

  15. Excessive magnetic field flux density distribution from overhead isolated powerline conductors due to neutral line current.

    Science.gov (United States)

    Netzer, Moshe

    2013-06-01

    Overhead isolated powerline conductors (hereinafter: "OIPLC") are the most compact form for distributing low voltage currents. From the known physics of magnetic field emission from 3-phase power lines, it is expected that excellent symmetry of the 120° shifted phase currents and where compact configuration of the 3-phase+neutral line exist, the phase current vectorial summation of the magnetic field flux density (MFFD) is expected to be extremely low. However, despite this estimation, an unexpectedly very high MFFD was found in at least three towns in Israel. This paper explains the reasons leading to high MFFD emissions from compact OIPLC and the proper technique to fix it. Analysis and measurement results had led to the failure hypothsis of neutral line poor connection design and poor grounding design of the HV-LV utility transformers. The paper elaborates on the low MFFD exposure level setup by the Israeli Environmental Protection Office which adopted a rather conservative precaution principal exposure level (2 mG averaged over 24 h).

  16. Extracting functional components of neural dynamics with Independent Component Analysis and inverse Current Source Density.

    Science.gov (United States)

    Lęski, Szymon; Kublik, Ewa; Swiejkowski, Daniel A; Wróbel, Andrzej; Wójcik, Daniel K

    2010-12-01

    Local field potentials have good temporal resolution but are blurred due to the slow spatial decay of the electric field. For simultaneous recordings on regular grids one can reconstruct efficiently the current sources (CSD) using the inverse Current Source Density method (iCSD). It is possible to decompose the resultant spatiotemporal information about the current dynamics into functional components using Independent Component Analysis (ICA). We show on test data modeling recordings of evoked potentials on a grid of 4 × 5 × 7 points that meaningful results are obtained with spatial ICA decomposition of reconstructed CSD. The components obtained through decomposition of CSD are better defined and allow easier physiological interpretation than the results of similar analysis of corresponding evoked potentials in the thalamus. We show that spatiotemporal ICA decompositions can perform better for certain types of sources but it does not seem to be the case for the experimental data studied. Having found the appropriate approach to decomposing neural dynamics into functional components we use the technique to study the somatosensory evoked potentials recorded on a grid spanning a large part of the forebrain. We discuss two example components associated with the first waves of activation of the somatosensory thalamus. We show that the proposed method brings up new, more detailed information on the time and spatial location of specific activity conveyed through various parts of the somatosensory thalamus in the rat.

  17. Large critical current density improvement in Bi-2212 wires through the groove-rolling process

    Science.gov (United States)

    Malagoli, A.; Bernini, C.; Braccini, V.; Romano, G.; Putti, M.; Chaud, X.; Debray, F.

    2013-04-01

    Recently there has been a growing interest in Bi-2212 superconductor round wire for high magnetic field use despite the fact that an increase of the critical current is still needed to boost its successful use in such applications. Recent studies have demonstrated that the main obstacle to current flow, especially in long wires, is the residual porosity inside these powder-in-tube processed conductors that develops from bubble agglomeration when the Bi-2212 melts. In this work we tried to overcome this issue affecting the wire densification by changing the deformation process. Here we show the effects of groove rolling versus the drawing process on the critical current density JC and on the microstructure. In particular, groove-rolled multifilamentary wires show a JC increased by a factor of about 3 with respect to drawn wires prepared with the same Bi-2212 powder and architecture. We think that this approach in the deformation process is able to produce the required improvements both because the superconducting properties are enhanced and because it makes the fabrication process faster and cheaper.

  18. Modelling the electric field and the current density generated by cerebellar transcranial DC stimulation in humans.

    Science.gov (United States)

    Parazzini, Marta; Rossi, Elena; Ferrucci, Roberta; Liorni, Ilaria; Priori, Alberto; Ravazzani, Paolo

    2014-03-01

    Transcranial Direct Current Stimulation (tDCS) over the cerebellum (or cerebellar tDCS) modulates working memory, changes cerebello-brain interaction, and affects locomotion in humans. Also, the use of tDCS has been proposed for the treatment of disorders characterized by cerebellar dysfunction. Nonetheless, the electric field (E) and current density (J) spatial distributions generated by cerebellar tDCS are unknown. This work aimed to estimate E and J distributions during cerebellar tDCS. Computational electromagnetics techniques were applied in three human realistic models of different ages and gender. The stronger E and J occurred mainly in the cerebellar cortex, with some spread (up to 4%) toward the occipital cortex. Also, changes by ±1cm in the position of the active electrode resulted in a small effect (up to 4%) in the E and J spatial distribution in the cerebellum. Finally, the E and J spreads to the brainstem and the heart were negligible, thus further supporting the safety of this technique. Despite inter-individual differences, our modeling study confirms that the cerebellum is the structure mainly involved by cerebellar tDCS. Modeling approach reveals that during cerebellar tDCS the current spread to other structures outside the cerebellum is unlike to produce functional effects. Copyright © 2013 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

  19. Critical current densities estimated from AC susceptibilities in proximity-induced superconducting matrix of multifilamentary wire

    Science.gov (United States)

    Akune, Tadahiro; Sakamoto, Nobuyoshi

    2009-03-01

    In a multifilamentary wire proximity-currents between filaments show a close resemblance with the inter-grain current in a high-Tc superconductor. The critical current densities of the proximity-induced superconducting matrix Jcm can be estimated from measured twist-pitch dependence of magnetization and have been shown to follow the well-known scaling law of the pinning strength. The grained Bean model is applied on the multifilamentary wire to obtain Jcm, where the filaments are immersed in the proximity-induced superconducting matrix. Difference of the superconducting characteristics of the filament, the matrix and the filament content factor give a variety of deformation on the AC susceptibility curves. The computed AC susceptibility curves of multifilamentary wires using the grained Bean model are favorably compared with the experimental results. The values of Jcm estimated from the susceptibilities using the grained Bean model are comparable to those estimated from measured twist-pitch dependence of magnetization. The applicability of the grained Bean model on the multifilamentary wire is discussed in detail.

  20. Critical current densities estimated from AC susceptibilities in proximity-induced superconducting matrix of multifilamentary wire

    Energy Technology Data Exchange (ETDEWEB)

    Akune, Tadahiro; Sakamoto, Nobuyoshi, E-mail: akune@te.kyusan-u.ac.j [Department of Electrical Engineering and Information Technology, Kyushu Sangyo University, 2-3-1 Matsukadai, Fukuoka 813-8503 (Japan)

    2009-03-01

    In a multifilamentary wire proximity-currents between filaments show a close resemblance with the inter-grain current in a high-T{sub c} superconductor. The critical current densities of the proximity-induced superconducting matrix J{sub cm} can be estimated from measured twist-pitch dependence of magnetization and have been shown to follow the well-known scaling law of the pinning strength. The grained Bean model is applied on the multifilamentary wire to obtain J{sub cm}, where the filaments are immersed in the proximity-induced superconducting matrix. Difference of the superconducting characteristics of the filament, the matrix and the filament content factor give a variety of deformation on the AC susceptibility curves. The computed AC susceptibility curves of multifilamentary wires using the grained Bean model are favorably compared with the experimental results. The values of J{sub cm} estimated from the susceptibilities using the grained Bean model are comparable to those estimated from measured twist-pitch dependence of magnetization. The applicability of the grained Bean model on the multifilamentary wire is discussed in detail.

  1. High critical current density in powder-in-tube processed MgB2/Ta/Cu wire

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The magnetization of dense MgB2/Ta/Cu wires prepared by the powder-in-tube method is measured by a SQUID magnetometer. The results indicate that the critical temperature of MgB2/Ta/Cu is around 38.4 K with a sharp transition width of 0.6 K. The MgB2/Ta/Cu wire shows a strong flux pinning and the critical current density is higher than 105 A/cm2 (5 K, self-field) and 104 A/cm2 (20 K, 1 T). Also, the irreversibility field of the sample reaches 6.6 T at 5 K.

  2. THE CURRENT ASSESSMENT OF TEACHERS IN HIGHER EDUCATION AT THE INSTITUTO POLITÉCNICO NACIONAL

    Directory of Open Access Journals (Sweden)

    Juan José Arenas-Romero

    2014-07-01

    Full Text Available In this paper, the current form of teacher assessment at a higher level and criteria used, based on surveys of student opinion is analyzed. Such surveys do not reflect the real capacity of teachers and only serves as a form of administrative control. This paper establishes the utility of these assessments as a tool for improvement and as part of an early detection of needs, be altered by the biased way he handles himself. In addition, a criticism of this type of evaluation is done; the results are disclosed extemporaneously, which also restricts the development of teachers through the bureaucratic control of that information not timely feedback to teachers in order to improve their performance.

  3. Solar cells from 120 PPMA carbon-contaminated feedstock without significantly higher reverse current or shunt

    Energy Technology Data Exchange (ETDEWEB)

    Manshanden, P.; Coletti, G. [ECN Solar Energy, Petten (Netherlands)

    2012-09-15

    In a bid to drive down the cost of silicon wafers, several options for solar grade silicon feedstock have been investigated over the years. All methods have in common that the resulting silicon contains higher levels of impurities like dopants, oxygen, carbon or transition metals, the type and level of impurities depending on the raw materials and refining processes. In this work wafers from a p-type mc-Si ingot made with feedstock contaminated with 120 ppma of carbon have been processed into solar cells together with reference uncontaminated feedstock from semiconductor grade polysilicon with <0.4 ppma carbon. The results show that comparable reverse current, shunts, and efficiencies can be reached for both types of wafers. Gettering and defect hydrogenation effectiveness also did not deviate from the reference. Electroluminescence pictures do not show increased hotspot formation, even at -16V.

  4. Business intelligence and data warehouse programs in higher education institutions: current status and recommendations for improvement

    Directory of Open Access Journals (Sweden)

    Olga Marinova

    2016-11-01

    Full Text Available The purpose of this article is to explore the current situation and the main challenges in existing Business Intelligence (BI and Data Warehouse (DW curricula. On the base of this research, certain recommendations for their improvement are made. At the same time, the paper gives concrete guidelines for the development of a clear and comprehensive graduate profile with knowledge, skills and social competence in the field of BI and DW. This is particularly beneficial for universities and other higher education institutions, that seek to offer courses with high quality content and tendencies, adequate to the latest education, in the concerned area. The paper is written within the Erasmus plus KA2 project “Developing the innovative methodology of teaching Business Informatics” (DIMBI, 2015-1-PL01-KA203-0016636.

  5. Current guidelines for high-density lipoprotein cholesterol in therapy and future directions

    Directory of Open Access Journals (Sweden)

    Subedi BH

    2014-04-01

    Full Text Available Bishnu H Subedi,1,2 Parag H Joshi,1 Steven R Jones,1 Seth S Martin,1 Michael J Blaha,1 Erin D Michos1 1Johns Hopkins Ciccarone Center for the Prevention of Heart Disease, 2Greater Baltimore Medical Center, Baltimore, MD, USA Abstract: Many studies have suggested that a significant risk factor for atherosclerotic cardiovascular disease (ASCVD is low high-density lipoprotein cholesterol (HDL-C. Therefore, increasing HDL-C with therapeutic agents has been considered an attractive strategy. In the prestatin era, fibrates and niacin monotherapy, which cause modest increases in HDL-C, reduced ASCVD events. Since their introduction, statins have become the cornerstone of lipoprotein therapy, the benefits of which are primarily attributed to decrease in low-density lipoprotein cholesterol. Findings from several randomized trials involving niacin or cholesteryl ester transfer protein inhibitors have challenged the concept that a quantitative elevation of plasma HDL-C will uniformly translate into ASCVD benefits. Consequently, the HDL, or more correctly, HDL-C hypothesis has become more controversial. There are no clear guidelines thus far for targeting HDL-C or HDL due to lack of solid outcomes data for HDL specific therapies. HDL-C levels are only one marker of HDL out of its several structural or functional properties. Novel approaches are ongoing in developing and assessing agents that closely mimic the structure of natural HDL or replicate its various functions, for example, reverse cholesterol transport, vasodilation, anti-inflammation, or inhibition of platelet aggregation. Potential new approaches like HDL infusions, delipidated HDL, liver X receptor agonists, Apo A-I upregulators, Apo A mimetics, and gene therapy are in early phase trials. This review will outline current therapies and describe future directions for HDL therapeutics. Keywords: high-density lipoprotein, lipids, cholesterol, atherosclerosis, cardiovascular disease, therapy

  6. Scalp current density mapping in the analysis of mismatch negativity paradigms.

    Science.gov (United States)

    Giard, Marie-Hélène; Besle, Julien; Aguera, Pierre-Emmanuel; Gomot, Marie; Bertrand, Olivier

    2014-07-01

    MMN oddball paradigms are frequently used to assess auditory (dys)functions in clinical populations, or the influence of various factors (such as drugs and alcohol) on auditory processing. A widely used procedure is to compare the MMN responses between two groups of subjects (e.g. patients vs controls), or between experimental conditions in the same group. To correctly interpret these comparisons, it is important to take into account the multiple brain generators that produce the MMN response. To disentangle the different components of the MMN, we describe the advantages of scalp current density (SCD)-or surface Laplacian-computation for ERP analysis. We provide a short conceptual and mathematical description of SCDs, describe their properties, and illustrate with examples from published studies how they can benefit MMN analysis. We conclude with practical tips on how to correctly use and interpret SCDs in this context.

  7. Current source density estimation and interpolation based on the spherical harmonic Fourier expansion.

    Science.gov (United States)

    Pascual-Marqui, R D; Gonzalez-Andino, S L; Valdes-Sosa, P A; Biscay-Lirio, R

    1988-12-01

    A method for the spatial analysis of EEG and EP data, based on the spherical harmonic Fourier expansion (SHE) of scalp potential measurements, is described. This model provides efficient and accurate formulas for: (1) the computation of the surface Laplacian and (2) the interpolation of electrical potentials, current source densities, test statistics and other derived variables. Physiologically based simulation experiments show that the SHE method gives better estimates of the surface Laplacian than the commonly used finite difference method. Cross-validation studies for the objective comparison of different interpolation methods demonstrate the superiority of the SHE over the commonly used methods based on the weighted (inverse distance) average of the nearest three and four neighbor values.

  8. Current-source density analysis of slow brain potentials during time estimation.

    Science.gov (United States)

    Gibbons, Henning; Rammsayer, Thomas H

    2004-11-01

    Two event-related potential studies were conducted to investigate differential brain correlates of temporal processing of intervals below and above 3-4 s. In the first experiment, 24 participants were presented with auditorily marked target durations of 2, 4, and 6 s that had to be reproduced. Timing accuracy was similar for all three target durations. As revealed by current-source density analysis, slow-wave components during both presentation and reproduction were independent of target duration. Experiment 2 examined potential modulating effects of type of interval (filled and empty) and presentation mode (randomized and blocked presentation of target durations). Behavioral and slow-wave findings were consistent with those of Experiment 1. Thus, the present findings support the notion of a general timing mechanism irrespective of interval duration as proposed by scalar timing theory and pacemaker-counter models of time estimation.

  9. Estimation of population firing rates and current source densities from laminar electrode recordings.

    Science.gov (United States)

    Pettersen, Klas H; Hagen, Espen; Einevoll, Gaute T

    2008-06-01

    This model study investigates the validity of methods used to interpret linear (laminar) multielectrode recordings. In computer experiments extracellular potentials from a synaptically activated population of about 1,000 pyramidal neurons are calculated using biologically realistic compartmental neuron models combined with electrostatic forward modeling. The somas of the pyramidal neurons are located in a 0.4 mm high and wide columnar cylinder, mimicking a stimulus-evoked layer-5 population in a neocortical column. Current-source density (CSD) analysis of the low-frequency part (estimates of the true underlying CSD. The high-frequency part (>750 Hz) of the potentials (multi-unit activity, MUA) is found to scale approximately as the population firing rate to the power 3/4 and to give excellent estimates of the underlying population firing rate for trial-averaged data. The MUA signal is found to decay much more sharply outside the columnar populations than the LFP.

  10. Current density in generalized Fibonacci superlattices under a uniform electric field.

    Science.gov (United States)

    Panchadhyayee, P; Biswas, R; Khan, Arif; Mahapatra, P K

    2008-07-09

    We present an exhaustive study on tunneling and electrical conduction in an electrically biased GaAs-Al(y)Ga(1-y)As generalized Fibonacci superlattice. The study is based on transfer matrix formalism using an Airy function approach and provides an exact calculation of the current density in the case of quasi-periodic multibarrier systems. The results suggest the use of such quasi-periodic systems in perfect band-pass or band-eliminator (of extremely low width) circuitry. We have clearly demonstrated the resonance-type peaks and negative differential conductivity regimes in such systems. It has also been found that quasi-periodicity favors sharp negative differential conductivity peaks compared to those in periodic superlattices and thus have profound importance in device applications.

  11. PERFORMANCE OPTIMIZATION OF LINEAR INDUCTION MOTOR BY EDDY CURRENT AND FLUX DENSITY DISTRIBUTION ANALYSIS

    Directory of Open Access Journals (Sweden)

    M. S. MANNA

    2011-12-01

    Full Text Available The development of electromagnetic devices as machines, transformers, heating devices confronts the engineers with several problems. For the design of an optimized geometry and the prediction of the operational behaviour an accurate knowledge of the dependencies of the field quantities inside the magnetic circuits is necessary. This paper provides the eddy current and core flux density distribution analysis in linear induction motor. Magnetic flux in the air gap of the Linear Induction Motor (LIM is reduced to various losses such as end effects, fringes, effect, skin effects etc. The finite element based software package COMSOL Multiphysics Inc. USA is used to get the reliable and accurate computational results for optimization the performance of Linear Induction Motor (LIM. The geometrical characteristics of LIM are varied to find the optimal point of thrust and minimum flux leakage during static and dynamic conditions.

  12. An unusually energetic basaltic phreatomagmatic eruption: Using deposit characteristics to constrain dilute pyroclastic density current dynamics

    Science.gov (United States)

    Brand, Brittany D.; Clarke, Amanda B.

    2012-10-01

    Multiple, highly erosive base surges of the Table Rock Complex tuff ring (TRC2), Oregon, produced dune-bedded deposits with crest to crest bedform wavelengths up to 200 m, which are amongst the largest ever recognized in the deposits of pyroclastic density currents. Here we use bedform wavelength, surmounted obstacles, and a large chute-and-pool feature to estimate near-source velocities (118-233 m s- 1), lower-bound velocities at radial distances of 1.6, 2 and 4.7 km from source (34, 29 and 20 m s- 1, respectively), and corresponding column collapse heights (up to 2.8 km). This paper represents one of the few studies that attempt to quantify flow characteristics, such as emplacement velocities at different distances from source, eruption column collapse height, and eruptive energy, based on deposit characteristics.

  13. Fracture behaviors of thin superconducting films with field-dependent critical current density

    Science.gov (United States)

    He, An; Xue, Cun; Yong, Huadong; Zhou, Youhe

    2013-09-01

    The fracture behaviors under electromagnetic force with field-dependent critical current density in thin superconducting film are investigated. Applying finite element method, the energy release rates and stress intensity factors of one central crack versus applied field and crack length are obtained for the Bean model and Kim model. It is interesting that the profile of the stress intensity factor is generally the same as the magnetostrictive behavior during one full cycle applied field. Furthermore, the crack problem of two collinear cracks with respect to crack length and distance is also researched for the Kim model. The results show that the energy release rates and stress intensity factors of the two collinear cracks at left tip and right tip are remarkably different for relatively small crack distance and long crack length. This work can offer good estimations and provide a basis for interpretation of cracking and mechanical failure of HTS thin films in numerous real situations.

  14. High critical current densities in industrial scale composites made from high homogeneity NB 46. 5 TI

    Energy Technology Data Exchange (ETDEWEB)

    Larbalestier, D.C.; Hemachalam, K.; Lee, P.; McDonald, W.K.; O' Larey, P.; Scanlan, R.; Starch, W.; Taylor, C.; Warnes, W.; West, A.W.; Zeitlin, B.

    1985-03-01

    Recent work in our group on the fabricationmicrostructure-superconducting properties of composites of Nb-Ti has produced much new information about the precipitate morphology and origins of high critical current density (J /SUB c/ ) in these materials./sup 1 -4/ Precipitation of Ti-rich phase is seen to commence as a grain boundary film 2 - 4 nm thick, the film then developing into approximately equiaxed particles of ..cap alpha..-Ti at the boundary triple points. The typical size of such precipitates is 50 - 100 nm. Controlled drawing of such a structure produces an array of locally ordered ribbon precipitates. These precipitates are typically 3 - 5 nm thick by 100 - 300 nm long (when observed in transverse section). Their length in longitudinal section appears to be several hundred nm, indicating great ductility in these small ..cap alpha..-Ti precipitates. The typical separation of the precipitates is 20 - 30 nm. Thus the dimensions of the precipitate array are quite comparable to that of the flux lattice since the fluxoid separation is 22 nm at 5 T and the fluxoid diameter of Nb 46.5 wt% Ti is approximately 10 nm. The flux pinning behavior of these precipitate structures is expected to be complex: /SUP 2.4/ the defect density is very high, the precipitate morphology has a very high aspect ratio and the extreme thinness of the precipitates must permit some superconductivity to be induced in them by the proximity effect./sup 5/

  15. Critical current densities in Ag-added bulk MgB{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Muralidhar, M., E-mail: miryala1@shibaura-it.ac.jp [Superconducting Materials Laboratory, Department of Materials Science and Engineering, Shibaura Institute of Technology, 3-7-5 Toyosu, Koto-ku, Tokyo 135-8548 (Japan); Inoue, K. [Superconducting Materials Laboratory, Department of Materials Science and Engineering, Shibaura Institute of Technology, 3-7-5 Toyosu, Koto-ku, Tokyo 135-8548 (Japan); Koblischka, M.R. [Experimental Physics, Saarland University, Campus C 6 3, 66123 Saarbrücken (Germany); Murakami, M. [Superconducting Materials Laboratory, Department of Materials Science and Engineering, Shibaura Institute of Technology, 3-7-5 Toyosu, Koto-ku, Tokyo 135-8548 (Japan)

    2015-11-15

    Highlights: • Bulk MgB{sub 2} samples with Ag contents of 0–10 wt% were sintered at 775 °C for 3 h. • Magnetization measurements showed a sharp superconducting transition with T{sub c} (onset) around 38.5–38.7 K. • Atomic force microscopy indicated that Ag-based MgB{sub 2} particles are of nanometer size. • The sample with 4 wt% Ag addition exhibited the highest J{sub c} of 400 kA/cm{sup 2} at 10 K and self field. - Abstract: In previous studies, we found that bulk MgB{sub 2} contained numerous voids in various shapes and sizes. With the aim of improving the critical current density as well as the mechanical performance of the disk-shaped MgB{sub 2} bulk superconductors, we added Ag and optimized the processing conditions. The samples with varied Ag content from 0, 2, 4, 6, to 10 wt% were synthesized in pure Ar atmosphere. Microstructural observation by scanning electron microscopy confirmed that metallic Ag particles are embedded in the void regions. Furthermore, atomic force microscopy indicated that silver-based MgB{sub 2} particles are of nanometer size. As a result, the critical current density (J{sub c}) values were improved with Ag addition as compared to pure MgB{sub 2} bulk. The sample with 4 wt% Ag addition exhibited the highest J{sub c} of 293 kA/cm{sup 2} at 20 K and self field. The respective J{sub c} values at 10 K were 400 kA/cm{sup 2}, 300 kA/cm{sup 2}, and 100 kA/cm{sup 2} in self field, 1 T and 2 T. These values are the highest record values so far reported in bulk MgB{sub 2} materials.

  16. Effect of higher implant density on curve correction in dystrophic thoracic scoliosis secondary to neurofibromatosis Type 1.

    Science.gov (United States)

    Li, Yang; Yuan, Xinxin; Sha, Shifu; Liu, Zhen; Zhu, Weiguo; Qiu, Yong; Wang, Bin; Yu, Yang; Zhu, Zezhang

    2017-10-01

    OBJECTIVE The aim of this study was to investigate how implant density affects radiographic results and clinical outcomes in patients with dystrophic scoliosis secondary to neurofibromatosis Type 1 (NF1). METHODS A total of 41 patients with dystrophic scoliosis secondary to NF1 who underwent 1-stage posterior correction between June 2011 and December 2013 were included. General information about patients was recorded, as were preoperative and postoperative scores from Scoliosis Research Society (SRS)-22 questionnaires. Pearson correlation analysis was used to analyze the associations among implant density, coronal Cobb angle correction rate and correction loss at last follow-up, change of sagittal curve, and apical vertebral translation. Patients were then divided into 2 groups: those with low-density and those with high-density implants. Independent-sample t-tests were used to compare demographic data, radiographic findings, and clinical outcomes before surgery and at last follow-up between the groups. RESULTS Significant correlations were found between the implant density and the coronal correction rate of the main curve (r = 0.505, p density and change of sagittal profile (p = 0.662) or apical vertebral translation (p = 0.062). The SRS-22 scores improved in the appearance, activity, and mental health domains within both groups, but there was no difference between the groups in any of the SRS-22 domains at final follow-up (p > 0.05 for all). CONCLUSIONS Although no significant differences between the high- and low-density groups were found in any of the SRS-22 domains at final follow-up, higher implant density was correlated with superior coronal correction and less postoperative correction loss in patients with dystrophic NF1-associated scoliosis.

  17. Analysis of plasma equilibrium based on orbit-driven current density profile in steady-state plasma on QUEST

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, K., E-mail: nakamura@triam.kyushu-u.ac.jp [RIAM, Kyushu University, Kasuga 816-8580 (Japan); Alam, M.M. [IGSES, Kyushu University, Kasuga 816-8580 (Japan); Jiang, Y.Z. [Tsinghua University, Beijing 100084 (China); Mitarai, O. [Tokai University, Kumamoto 862-8652 (Japan); Kurihara, K.; Kawamata, Y.; Sueoka, M.; Takechi, M. [Japan Atomic Energy Agency, Naka 311-0193 (Japan); Hasegawa, M.; Tokunaga, K.; Araki, K.; Zushi, H.; Hanada, K.; Fujisawa, A.; Idei, H.; Nagashima, Y.; Kawasaki, S.; Nakashima, H.; Higashijima, A.; Nagata, T. [RIAM, Kyushu University, Kasuga 816-8580 (Japan); and others

    2016-11-01

    Highlights: • High energy particle guiding center orbit is calculated as a contour plot of conserved variable. • Current density profile is analyzed based on the orbit-driven current. • Plasma equilibrium is reconstructed by considering the hollow current profile. - Abstract: In the present RF-driven (ECCD) steady-state plasma on QUEST (B{sub t} = 0.25 T, R = 0.68 m, a = 0.40 m), plasma current seems to flow in the open magnetic surface outside of the closed magnetic surface in the low-field region according to plasma current fitting (PCF) method. We consider that the current in the open magnetic surface is due to orbit-driven current by high-energy particles in RF-driven plasma. So based on the analysis of current density profile based on the orbit-driven current, plasma equilibrium is to be calculated. We calculated high energy particles guiding center orbits as a contour plot of conserved variable in Hamiltonian formulation and considered particles initial position with different levels of energy and pitch angles that satisfy resonance condition. Then the profile of orbit-driven current is estimated by multiplying the particle density on the resonance surface and the velocity on the orbits. This analysis shows negative current near the magnetic axis and hollow current profile is expected even if pressure driven current is considered. Considering the hollow current profile shifted toward the low-field region, the equilibrium is fitted by J-EFIT coded by MATLAB.

  18. Status Epilepticus Induced Spontaneous Dentate Gyrus Spikes: In Vivo Current Source Density Analysis.

    Science.gov (United States)

    Flynn, Sean P; Barriere, Sylvain; Barrier, Sylvain; Scott, Rod C; Lenck-Santini, Pierre-Pascal; Holmes, Gregory L

    2015-01-01

    The dentate gyrus is considered to function as an inhibitory gate limiting excitatory input to the hippocampus. Following status epilepticus (SE), this gating function is reduced and granule cells become hyper-excitable. Dentate spikes (DS) are large amplitude potentials observed in the dentate gyrus (DG) of normal animals. DS are associated with membrane depolarization of granule cells, increased activity of hilar interneurons and suppression of CA3 and CA1 pyramidal cell firing. Therefore, DS could act as an anti-excitatory mechanism. Because of the altered gating function of the dentate gyrus following SE, we sought to investigate how DS are affected following pilocarpine-induced SE. Two weeks following lithium-pilocarpine SE induction, hippocampal EEG was recorded in male Sprague-Dawley rats with 16-channel silicon probes under urethane anesthesia. Probes were placed dorso-ventrally to encompass either CA1-CA3 or CA1-DG layers. Large amplitude spikes were detected from EEG recordings and subject to current source density analysis. Probe placement was verified histologically to evaluate the anatomical localization of current sinks and the origin of DS. In 9 of 11 pilocarpine-treated animals and two controls, DS were confirmed with large current sinks in the molecular layer of the dentate gyrus. DS frequency was significantly increased in pilocarpine-treated animals compared to controls. Additionally, in pilocarpine-treated animals, DS displayed current sinks in the outer, middle and/or inner molecular layers. However, there was no difference in the frequency of events when comparing between layers. This suggests that following SE, DS can be generated by input from medial and lateral entorhinal cortex, or within the dentate gyrus. DS were associated with an increase in multiunit activity in the granule cell layer, but no change in CA1. These results suggest that following SE there is an increase in DS activity, potentially arising from hyperexcitability along the

  19. Direct numerical simulations of particle-laden density currents with adaptive, discontinuous finite elements

    Directory of Open Access Journals (Sweden)

    S. D. Parkinson

    2014-09-01

    Full Text Available High-resolution direct numerical simulations (DNSs are an important tool for the detailed analysis of turbidity current dynamics. Models that resolve the vertical structure and turbulence of the flow are typically based upon the Navier–Stokes equations. Two-dimensional simulations are known to produce unrealistic cohesive vortices that are not representative of the real three-dimensional physics. The effect of this phenomena is particularly apparent in the later stages of flow propagation. The ideal solution to this problem is to run the simulation in three dimensions but this is computationally expensive. This paper presents a novel finite-element (FE DNS turbidity current model that has been built within Fluidity, an open source, general purpose, computational fluid dynamics code. The model is validated through re-creation of a lock release density current at a Grashof number of 5 × 106 in two and three dimensions. Validation of the model considers the flow energy budget, sedimentation rate, head speed, wall normal velocity profiles and the final deposit. Conservation of energy in particular is found to be a good metric for measuring model performance in capturing the range of dynamics on a range of meshes. FE models scale well over many thousands of processors and do not impose restrictions on domain shape, but they are computationally expensive. The use of adaptive mesh optimisation is shown to reduce the required element count by approximately two orders of magnitude in comparison with fixed, uniform mesh simulations. This leads to a substantial reduction in computational cost. The computational savings and flexibility afforded by adaptivity along with the flexibility of FE methods make this model well suited to simulating turbidity currents in complex domains.

  20. Direct numerical simulations of particle-laden density currents with adaptive, discontinuous finite elements

    Science.gov (United States)

    Parkinson, S. D.; Hill, J.; Piggott, M. D.; Allison, P. A.

    2014-09-01

    High-resolution direct numerical simulations (DNSs) are an important tool for the detailed analysis of turbidity current dynamics. Models that resolve the vertical structure and turbulence of the flow are typically based upon the Navier-Stokes equations. Two-dimensional simulations are known to produce unrealistic cohesive vortices that are not representative of the real three-dimensional physics. The effect of this phenomena is particularly apparent in the later stages of flow propagation. The ideal solution to this problem is to run the simulation in three dimensions but this is computationally expensive. This paper presents a novel finite-element (FE) DNS turbidity current model that has been built within Fluidity, an open source, general purpose, computational fluid dynamics code. The model is validated through re-creation of a lock release density current at a Grashof number of 5 × 106 in two and three dimensions. Validation of the model considers the flow energy budget, sedimentation rate, head speed, wall normal velocity profiles and the final deposit. Conservation of energy in particular is found to be a good metric for measuring model performance in capturing the range of dynamics on a range of meshes. FE models scale well over many thousands of processors and do not impose restrictions on domain shape, but they are computationally expensive. The use of adaptive mesh optimisation is shown to reduce the required element count by approximately two orders of magnitude in comparison with fixed, uniform mesh simulations. This leads to a substantial reduction in computational cost. The computational savings and flexibility afforded by adaptivity along with the flexibility of FE methods make this model well suited to simulating turbidity currents in complex domains.

  1. The influence of current speed and vegetation density on flow structure in two macrotidal eelgrass canopies

    Science.gov (United States)

    Lacy, Jessica R.; Wyllie-Echeverria, Sandy

    2011-01-01

    The influence of eelgrass (Zostera marina) on near-bed currents, turbulence, and drag was investigated at three sites in two eelgrass canopies of differing density and at one unvegetated site in the San Juan archipelago of Puget Sound, Washington, USA. Eelgrass blade length exceeded 1 m. Velocity profiles up to 1.5 m above the sea floor were collected over a spring-neap tidal cycle with a downward-looking pulse-coherent acoustic Doppler profiler above the canopies and two acoustic Doppler velocimeters within the canopies. The eelgrass attenuated currents by a minimum of 40%, and by more than 70% at the most densely vegetated site. Attenuation decreased with increasing current speed. The data were compared to the shear-layer model of vegetated flows and the displaced logarithmic model. Velocity profiles outside the meadows were logarithmic. Within the canopies, most profiles were consistent with the shear-layer model, with a logarithmic layer above the canopy. However, at the less-dense sites, when currents were strong, shear at the sea floor and above the canopy was significant relative to shear at the top of the canopy, and the velocity profiles more closely resembled those in a rough-wall boundary layer. Turbulence was strong at the canopy top and decreased with height. Friction velocity at the canopy top was 1.5–2 times greater than at the unvegetated, sandy site. The coefficient of drag CD on the overlying flow derived from the logarithmic velocity profile above the canopy, was 3–8 times greater than at the unvegetated site (0.01–0.023 vs. 2.9 × 10−3).

  2. Status Epilepticus Induced Spontaneous Dentate Gyrus Spikes: In Vivo Current Source Density Analysis.

    Directory of Open Access Journals (Sweden)

    Sean P Flynn

    Full Text Available The dentate gyrus is considered to function as an inhibitory gate limiting excitatory input to the hippocampus. Following status epilepticus (SE, this gating function is reduced and granule cells become hyper-excitable. Dentate spikes (DS are large amplitude potentials observed in the dentate gyrus (DG of normal animals. DS are associated with membrane depolarization of granule cells, increased activity of hilar interneurons and suppression of CA3 and CA1 pyramidal cell firing. Therefore, DS could act as an anti-excitatory mechanism. Because of the altered gating function of the dentate gyrus following SE, we sought to investigate how DS are affected following pilocarpine-induced SE. Two weeks following lithium-pilocarpine SE induction, hippocampal EEG was recorded in male Sprague-Dawley rats with 16-channel silicon probes under urethane anesthesia. Probes were placed dorso-ventrally to encompass either CA1-CA3 or CA1-DG layers. Large amplitude spikes were detected from EEG recordings and subject to current source density analysis. Probe placement was verified histologically to evaluate the anatomical localization of current sinks and the origin of DS. In 9 of 11 pilocarpine-treated animals and two controls, DS were confirmed with large current sinks in the molecular layer of the dentate gyrus. DS frequency was significantly increased in pilocarpine-treated animals compared to controls. Additionally, in pilocarpine-treated animals, DS displayed current sinks in the outer, middle and/or inner molecular layers. However, there was no difference in the frequency of events when comparing between layers. This suggests that following SE, DS can be generated by input from medial and lateral entorhinal cortex, or within the dentate gyrus. DS were associated with an increase in multiunit activity in the granule cell layer, but no change in CA1. These results suggest that following SE there is an increase in DS activity, potentially arising from

  3. The Operator Product Expansion between the 16 Lowest Higher Spin Currents in the N=4 Superspace

    CERN Document Server

    Ahn, Changhyun

    2015-01-01

    Some of the operator product expansions (OPEs) between the lowest 16 higher spin currents of spins (1, 3/2, 3/2, 3/2, 3/2, 2, 2, 2, 2, 2, 2, 5/2, 5/2, 5/2, 5/2, 3) in an extension of the large N=4 linear superconformal algebra were constructed in the N=4 superconformal coset SU(5)/SU(3) theory previously. In this paper, by rewriting the above OPEs in the N=4 superspace developed by Schoutens (and other groups), the remaining undetermined OPEs where the corresponding singular terms possess the composite fields with spins s =7/2, 4, 9/2, 5 are completely determined. Furthermore, by introducing the arbitrary coefficients in front of the composite fields in the right hand sides of the above complete 136 OPEs, reexpressing them in the N=2 superspace and using the N=2 OPEs mathematica package by Krivonos and Thielemans, the complete structures of the above OPEs with fixed coefficient functions are obtained with the help of various Jacobi identities. Then one obtains ten N=2 super OPEs between the four N=2 higher sp...

  4. CURRENT STATUS OF AMAZONIAN ORNAMENTAL FISH FROM PERU WITH HIGHER DEMAND OF EXPORTATION

    Directory of Open Access Journals (Sweden)

    Ortiz, N.

    2008-01-01

    Full Text Available Current status of Amazonian ornamental fish from Peru with higher demand of exportation was analyzed. The ornamental freshwater fishes from Peru with higher demand are Osteoglossum bicirrhosum (Cuvier, 1829 (Osteoglossidae, followed by ray Potamotrygon motoro (Müller & Henle, 1841 (Potamotrygonidae. Main ornamental and continental fish family that exports is Loriicaridae (Siluriformes. The vast continental and ornamental fish from Peru with higher demand are climate tropical and clear waters with pH de 6.5 a 7.5. Four species (Potamotrygon falkneri Castex & Maciel, 1963, Acanthicus adonis Isbrücker & Nijssen, 1988, Peckoltia vittata (Steindachner, 1881 and Corydoras julii Steindachner, 1906 that exists are not reported on check-list of continental fishes from Peru performed by Ortega & Vari (1986 and, Chang & Ortega (1995. C. julii, is the unique fish not found in the ornamental fish list from Peru performed by “Instituto de Investigación de la Amazonia Peruana” (IIAP and “Comisión para la Promoción de Exportaciones” (PROMPEX. O. bicirrhosum, P. motoro, Corydoras arcuatus Elwin 1938 and C. julii are fish with more data obtained. Fish with less data obtained was Brachyplatystoma tigrinum (Britski, 1981. Main problematic observed on ornamental continental Peruvian fish since an ecological point of view, are pollution of fish environment, mainly by heavy metals, alteration on great scale from habitat, where lives and surroundings, and also, introduction alien species. The main problem that suffer commercialization of ornamental fish as in other species, is regulation and foment by part of authority respect to bio-business initiatives bio-business; generating confusion between user and lack of motivation legalities of these bionegocio.

  5. Shear Viscosity to Entropy Density Ratio in Higher Derivative Gravity with Momentum Dissipation

    CERN Document Server

    Wang, Yi-Li

    2016-01-01

    Recently, it has been suggested that there is a new bound for the shear viscosity to entropy density ratio that reads $\\eta/s\\gtrsim (T/\\Delta)^2$ as $T/\\Delta\\to 0$, where $\\Delta$ is a scale present in the zero temperature IR theory. In this paper, we investigate $\\eta/s$ in linear scalar fields modified Gauss-Bonnet theory that breaks translation invariance. We first calculate $\\eta/s$ both analytically and numerically and show its relationship with temperature in log-log plot. Our results are in good agreement with the new viscosity bound above. The causality is also considered in this work. We then find that there will be no causality violation if the linear scalar field is added and hence the constraint for the Gauss-Bonnet coupling $\\lambda$ vanishes.

  6. Current Issues in Finite-T Density-Functional Theory and Warm-Correlated Matter †

    Directory of Open Access Journals (Sweden)

    M. W. C. Dharma-wardana

    2016-03-01

    Full Text Available Finite-temperature density functional theory (DFT has become of topical interest, partly due to the increasing ability to create novel states of warm-correlated matter (WCM.Warm-dense matter (WDM, ultra-fast matter (UFM, and high-energy density matter (HEDM may all be regarded as subclasses of WCM. Strong electron-electron, ion-ion and electron-ion correlation effects and partial degeneracies are found in these systems where the electron temperature Te is comparable to the electron Fermi energy EF. Thus, many electrons are in continuum states which are partially occupied. The ion subsystem may be solid, liquid or plasma, with many states of ionization with ionic charge Zj. Quasi-equilibria with the ion temperature Ti ≠ Te are common. The ion subsystem in WCM can no longer be treated as a passive “external potential”, as is customary in T = 0 DFT dominated by solid-state theory or quantum chemistry. Many basic questions arise in trying to implement DFT for WCM. Hohenberg-Kohn-Mermin theory can be adapted for treating these systems if suitable finite-T exchange-correlation (XC functionals can be constructed. They are functionals of both the one-body electron density ne and the one-body ion densities ρj. Here, j counts many species of nuclei or charge states. A method of approximately but accurately mapping the quantum electrons to a classical Coulomb gas enables one to treat electron-ion systems entirely classically at any temperature and arbitrary spin polarization, using exchange-correlation effects calculated in situ, directly from the pair-distribution functions. This eliminates the need for any XC-functionals. This classical map has been used to calculate the equation of state of WDM systems, and construct a finite-T XC functional that is found to be in close agreement with recent quantum path-integral simulation data. In this review, current developments and concerns in finite-T DFT, especially in the context of non-relativistic warm

  7. Application of hybrid supercapacitor using granule Li4Ti5O12/activated carbon with variation of current density

    Science.gov (United States)

    Lee, Byung-Gwan; Lee, Seung-Hwan

    2017-03-01

    We report the electrochemical performance of asymmetric hybrid supercapacitors composed of granule Li4Ti5O12 as an anode and activated carbon as a cathode with different current densities. It is demonstrated that the hybrid supercapacitors show good initial discharge capacities were ranged from 39.8 to 46.4 F g-1 in the current densities range of 0.3-1 A g-1. The performance degradation is proportional to the current density due to quick gassing, resulting from H2O and HF formation. In particular, the hybrid supercapacitors show the pretty good cycling stability of 97.4%, even at the high current density of 0.8 A g-1, which are among most important performance in the real application for energy storage devices. Therefore, we believe that hybrid supercapacitors using granule Li4Ti5O12/activated carbon are eligible for the promising next generation energy devices.

  8. Influence of the initial parameters of the magnetic field and plasma on the spatial structure of the electric current and electron density in current sheets formed in helium

    Energy Technology Data Exchange (ETDEWEB)

    Ostrovskaya, G. V., E-mail: galya-ostr@mail.ru [Russian Academy of Sciences, Ioffe Physical Technical Institute (Russian Federation); Markov, V. S.; Frank, A. G., E-mail: annfrank@fpl.gpi.ru [Russian Academy of Sciences, Prokhorov General Physics Institute (Russian Federation)

    2016-01-15

    The influence of the initial parameters of the magnetic field and plasma on the spatial structure of the electric current and electron density in current sheets formed in helium plasma in 2D and 3D magnetic configurations with X-type singular lines is studied by the methods of holographic interferometry and magnetic measurements. Significant differences in the structures of plasma and current sheets formed at close parameters of the initial plasma and similar configurations of the initial magnetic fields are revealed.

  9. High critical current density and enhanced irreversibility field in superconducting MgB2 thin films.

    Science.gov (United States)

    Eom, C B; Lee, M K; Choi, J H; Belenky, L J; Song, X; Cooley, L D; Naus, M T; Patnaik, S; Jiang, J; Rikel, M; Polyanskii, A; Gurevich, A; Cai, X Y; Bu, S D; Babcock, S E; Hellstrom, E E; Larbalestier, D C; Rogado, N; Regan, K A; Hayward, M A; He, T; Slusky, J S; Inumaru, K; Haas, M K; Cava, R J

    2001-05-31

    The discovery of superconductivity at 39 K in magnesium diboride offers the possibility of a new class of low-cost, high-performance superconducting materials for magnets and electronic applications. This compound has twice the transition temperature of Nb3Sn and four times that of Nb-Ti alloy, and the vital prerequisite of strongly linked current flow has already been demonstrated. One possible drawback, however, is that the magnetic field at which superconductivity is destroyed is modest. Furthermore, the field which limits the range of practical applications-the irreversibility field H*(T)-is approximately 7 T at liquid helium temperature (4.2 K), significantly lower than about 10 T for Nb-Ti (ref. 6) and approximately 20 T for Nb3Sn (ref. 7). Here we show that MgB2 thin films that are alloyed with oxygen can exhibit a much steeper temperature dependence of H*(T) than is observed in bulk materials, yielding an H* value at 4.2 K greater than 14 T. In addition, very high critical current densities at 4.2 K are achieved: 1 MA cm-2 at 1 T and 105 A cm-2 at 10 T. These results demonstrate that MgB2 has potential for high-field superconducting applications.

  10. Phase development and critical current density of Bi-2223 tapes fabricated by groove rolling

    Science.gov (United States)

    Iyer, A. N.; Salib, S.; Vipulanandan, C.; Salama, K.; Balachandran, U.

    1999-07-01

    The powder-in-tube technique is the most widely used method for fabricating silver-clad Bi-2223 wires and tapes. In this method the silver billet containing the precursor material is transformed to the final shape using metallurgical deformation techniques such as wire drawing and flat rolling. In the present study, a modified version of the powder-in-tube technique was adopted where the silver billet was reduced in size by groove rolling instead of wire drawing. Microstructural analysis during the initial deformation stage revealed crack formation in the superconductor core. Stress conditions during groove rolling were analysed and appropriate changes were incorporated in the deformation process. After groove rolling the wires were flat rolled to a final thickness of 250 icons/Journals/Common/mu" ALT="mu" ALIGN="TOP"/>m. Subsequent thermomechanical treatment resulted in tapes with critical current density of icons/Journals/Common/approx" ALT="approx" ALIGN="TOP"/>19700 A cm-2 (critical current of icons/Journals/Common/approx" ALT="approx" ALIGN="TOP"/>40 A).

  11. First test of BNL electron beam ion source with high current density electron beam

    Energy Technology Data Exchange (ETDEWEB)

    Pikin, Alexander, E-mail: pikin@bnl.gov; Alessi, James G., E-mail: pikin@bnl.gov; Beebe, Edward N., E-mail: pikin@bnl.gov [Brookhaven National Laboratory, Upton, NY 11973 (United States); Shornikov, Andrey; Mertzig, Robert; Wenander, Fredrik; Scrivens, Richard [CERN, CH-1211 Geneva 23 (Switzerland)

    2015-01-09

    A new electron gun with electrostatic compression has been installed at the Electron Beam Ion Source (EBIS) Test Stand at BNL. This is a collaborative effort by BNL and CERN teams with a common goal to study an EBIS with electron beam current up to 10 A, current density up to 10,000 A/cm{sup 2} and energy more than 50 keV. Intensive and pure beams of heavy highly charged ions with mass-to-charge ratio < 4.5 are requested by many heavy ion research facilities including NASA Space Radiation Laboratory (NSRL) at BNL and HIE-ISOLDE at CERN. With a multiampere electron gun, the EBIS should be capable of delivering highly charged ions for both RHIC facility applications at BNL and for ISOLDE experiments at CERN. Details of the electron gun simulations and design, and the Test EBIS electrostatic and magnetostatic structures with the new electron gun are presented. The experimental results of the electron beam transmission are given.

  12. Metal based gas diffusion layers for enhanced fuel cell performance at high current densities

    Science.gov (United States)

    Hussain, Nabeel; Van Steen, Eric; Tanaka, Shiro; Levecque, Pieter

    2017-01-01

    The gas diffusion layer strongly influences the performance and durability of polymer electrolyte fuel cells. A major drawback of current carbon fiber based GDLs is the non-controlled variation in porosity resulting in a random micro-structure. Moreover, when subjected to compression these materials show significant reduction in porosity and permeability leading to water management problems and mass transfer losses within the fuel cell. This study investigated the use of uniform perforated metal sheets as GDLs in conjunction with microchannel flowfields. A metal sheet design with a pitch of 110 μm and a hole diameter of 60 μm in combination with an MPL showed superior performance in the high current density region compared to a commercially available carbon paper based GDL in a single cell environment. Fuel cell testing with different oxidants (air, heliox and oxygen) indicate that the metal sheet offers both superior diffusion and reduced flooding in comparison to the carbon based GDL. The presence of the MPL has been found to be critical to the functionality of the metal sheet suggesting that the MPL design may represent an important optimisation parameter for further improvements in performance.

  13. Temperature and Magnetic Field Dependence of Critical Current Density of YBCO with Varying Flux Pinning Additions (POSTPRINT)

    Science.gov (United States)

    2010-03-01

    AFRL-RZ-WP-TP-2010-2083 TEMPERATURE AND MAGNETIC FIELD DEPENDENCE OF CRITICAL CURRENT DENSITY OF YBCO WITH VARYING FLUX PINNING ADDITIONS...MAGNETIC FIELD DEPENDENCE OF CRITICAL CURRENT DENSITY OF YBCO WITH VARYING FLUX PINNING ADDITIONS (POSTPRINT) 5a. CONTRACT NUMBER In-house 5b...20 ‒ 77 K. Films were prepared with pulsed laser deposition by (M/ YBCO )N multilayer or ( YBCO )1-x Mx single-target methods, for different M phases

  14. Theory of excluded volume equation of state: higher approximations and new generation of equations of state for entire density range.

    Science.gov (United States)

    Rusanov, Anatoly I

    2004-07-22

    A novel theory of an equation of state based on excluded volume and formulated in two preceding papers for gases and gaseous mixtures is extended to the entire density range by considering higher (beginning from the third) approximations of the theory. The algorithm of constructing higher approximations is elaborated. Equations of state are deduced using the requirement of maximum simplicity and contain a single free parameter to be chosen by reason of convenience or simplicity or to be used as a fitting parameter with respect to the computer simulation database. In this way, precise equations of state are derived for the hard-sphere fluid in the entire density range. On the side, the theory reproduces most known earlier equations of state for hard spheres and determines their place in the hierarchy of approximations. Equations of state for van der Waals fluids are also presented, and their critical parameters are estimated.

  15. Current-density functional theory study of the H2 molecule evolving under a strong ultrashort magnetic field

    Science.gov (United States)

    Vikas, Hash(0xb7f6e60)

    2012-01-01

    Hydrogen molecule in a strong ultrashort magnetic field is investigated through a current-density functional theory (CDFT) and quantum fluid dynamics (QFD) based approach employing current-density dependent vector exchange-correlation potential and energy density functional derived with a vorticity variable. The numerical computations through the CDFT based approach are performed for the H2 molecule, starting initially from its field-free ground state, in a parallel internuclear axis and magnetic field-axis configuration with the internuclear separation R ranging from 0.1 a.u. to 14.0 a.u., and the strength of the time-dependent (TD) magnetic field varying between 0-1011 G over a few femtoseconds. The numerical results are compared with that obtained using an approach based on the current-density independent approximation under similar computational constraints but employing only scalar exchange-correlation potential dependent on the electronic charge-density alone. The current-density based approach yields exchange- and correlation energy as well as electronic charge-density of the H2 molecule drastically different from that obtained using current-independent approach, in particular, at TD magnetic field-strengths >109 G during a typical time-period of the field when the magnetic-field had attained maximum applied field-strength and is switched to a decreasing ramp function. This nonadiabatic behavior of the TD electronic charge-density is traced to the TD vorticity-dependent vector exchange-correlation potential of the CDFT based approach. The interesting electron dynamics of the H2 molecule in strong TD magnetic field is further elucidated by treating electronic charge-density as an `electron-fluid'. The present work also reveals interesting real-time dynamics on the attosecond time-scale in the electronic charge-density distribution of the hydrogen molecule.

  16. Theoretical Limit to the Laser Threshold Current Density in an InGaN Quantume Well Laser

    Energy Technology Data Exchange (ETDEWEB)

    Amano, H; Chow, W W; Han, J

    1998-10-09

    This paper describes an investigation of the spontaneous emission limit to the laser threshold current density in an InGaN quantum well laser. The peak gain and spontaneous emission rate as functions of carrier density are com- puted using a microscopic laser theory. From these quantities, the minimum achievable threshold current density is determined for a given threshold gain. The dependence on quantum well width, and the effects of inhomogeneous broadening due to spatial alloy variations are discussed. Also, comparison with experiments is made.

  17. Residual magnetic field profiles and their current density profiles of coated conductors for fast and slow cut-off current operations

    Energy Technology Data Exchange (ETDEWEB)

    Sun, J.; Taillouli, M.; Hamabe, M.; Watanabe, H.; Chikumoto, N.; Yamaguchi, S. [Chubu University, Kasugai, Aichi (Japan); Shyshkin, O. [V. N. Karazin Kharkiv National University, Kharkov (Ukraine)

    2015-03-15

    Coated conductor is an important candidate for power cable applications due to its high current density. Even for DC power cable transmission, we must study the transport properties of HTS tapes after slow and fast discharge. In order to evaluate relation of the magnetic field with applied current we developed a scanning magnetic field measurements system by employing a Hall probe. This work presents the measurements of the magnetic fields above a coated conductor by varying applied current pattern. In the work, a transport current of 100 A, less than the critical current, is applied to YBCO coated conductor. We measured the residual magnetic field distributions after cut off the transport current with slow and fast operations. The results show differences of the magnetic field profiles and the corresponding current profiles by an inverse solution from the magnetic field measurement between these two operations because of the hysteresis of coated conductor excited by the transport current.

  18. Photonic Integrated Circuits for Cost-Effective, High Port Density, and Higher Capacity Optical Communications Systems

    Science.gov (United States)

    Chiappa, Pierangelo

    Bandwidth-hungry services, such as higher speed Internet, voice over IP (VoIP), and IPTV, allow people to exchange and store huge amounts of data among worldwide locations. In the age of global communications, domestic users, companies, and organizations around the world generate new contents making bandwidth needs grow exponentially, along with the need for new services. These bandwidth and connectivity demands represent a concern for operators who require innovative technologies to be ready for scaling. To respond efficiently to these demands, Alcatel-Lucent is fast moving toward photonic integration circuits technologies as the key to address best performances at the lowest "bit per second" cost. This article describes Alcatel-Lucent's contribution in strategic directions or achievements, as well as possible new developments.

  19. The Influence of Current Density and Frequency on the Microstructure and Corrosion Behavior of Plasma Electrolytic Oxidation Coatings on Ti6Al4V

    Science.gov (United States)

    Khanmohammadi, H.; Allahkaram, S. R.; Igual Munoz, A.; Towhidi, N.

    2017-02-01

    The effect of processing current density and frequency on the microstructure and corrosion behavior of the PEO coatings was studied. Coatings were characterized using FESEM, EDS, potentiodynamic polarization and EIS. The results indicated that the surface roughness, porosity and Al/Ti chemical value on the surface of the coatings increase with an increase in the current density and a decrease in the frequency of the PEO process. Corrosion investigations showed a relation between a mixed structural parameter (that contains thickness, porosity percentage and average pore diameter of the coatings) and the corrosion resistance of the PEO coatings. EIS data showed that higher coating thickness, lower surface porosity percentage and smaller pore diameter lead to the higher corrosion resistance.

  20. Enhancement of the critical current density in FeO-coated MgB2 thin films at high magnetic fields

    Directory of Open Access Journals (Sweden)

    Andrei E. Surdu

    2011-12-01

    Full Text Available The effect of depositing FeO nanoparticles with a diameter of 10 nm onto the surface of MgB2 thin films on the critical current density was studied in comparison with the case of uncoated MgB2 thin films. We calculated the superconducting critical current densities (Jc from the magnetization hysteresis (M–H curves for both sets of samples and found that the Jc value of FeO-coated films is higher at all fields and temperatures than the Jc value for uncoated films, and that it decreases to ~105 A/cm2 at B = 1 T and T = 20 K and remains approximately constant at higher fields up to 7 T.

  1. Novel algorithm for identifying T-wave current density alternans using synthesized 187-channel vector-projected body surface mapping.

    Science.gov (United States)

    Nakai, Kenji; Takahashi, Shin; Suzuki, Atsushi; Hagiwara, Nobuhisa; Futagawa, Keisuke; Shoda, Morio; Shiga, Tsuyoshi; Takahashi, Ken; Okabayashi, Hitoshi; Itoh, Manabu; Kasanuki, Hiroshi

    2011-03-01

    The noninvasive evaluation of ventricular T-wave alternans (TWA) in patients with lethal ventricular arrhythmias is an important issue. In this study, we propose a novel algorithm to identify T-wave current density alternans (TWCA) using synthesized 187-channel vector-projected body surface mapping (187-ch SAVP-ECG). We recorded 10 min of 187-ch SAVP-ECG using a Mason-Likar lead system in the supine position. A recovery time (RT) dispersion map was obtained by averaging the 187-ch SAVP-ECG. The TWCA value was determined from the relative changes in the averaged current density in the T-wave zone (Tpeak ± 50 ms) for two T-wave types. We registered 20 ECG recordings from normal controls and 11 ECG recordings from nine subjects with long QT syndrome (LQT). We divided LQT syndrome subjects into two groups: group 1 provided 9 ECG recordings without visually apparent TWAs, and group 2 provided 2 ECG recordings with visually apparent TWAs. The QTc interval values in the LQT groups were higher than those in the control (515 ± 60 ms in LQT G-1, 600 ± 27 ms in LQT G-2 vs. 415 ± 19 ms in control, P < 0.001). The RTendc dispersion values among the LQT subjects were higher than those of the control subjects (48 ± 19 ms in LQT G-1, 65 ± 30 ms in LQT G-2 vs. 24 ± 10 ms in control, P < 0.01). The mean TWCA value was significantly higher in the LQT G-2 group with visually apparent TWCAs (0.5 ± 0.2% in control, 2.1 ± 1.2% in LQT G-1, and 32.3 ± 6.9% in LQT G-2). Interestingly, the two-dimensional distribution of TWCA in LQT was inhomogeneous and correlated with the distribution of increased RT dispersion. We conclude that a novel algorithm using 187-ch SAVP-ECG might provide new insights into body surface TWCA.

  2. The Case for Higher Computational Density in the Memory-Bound FDTD Method within Multicore Environments

    Directory of Open Access Journals (Sweden)

    Mohammed F. Hadi

    2012-01-01

    Full Text Available It is argued here that more accurate though more compute-intensive alternate algorithms to certain computational methods which are deemed too inefficient and wasteful when implemented within serial codes can be more efficient and cost-effective when implemented in parallel codes designed to run on today's multicore and many-core environments. This argument is most germane to methods that involve large data sets with relatively limited computational density—in other words, algorithms with small ratios of floating point operations to memory accesses. The examples chosen here to support this argument represent a variety of high-order finite-difference time-domain algorithms. It will be demonstrated that a three- to eightfold increase in floating-point operations due to higher-order finite-differences will translate to only two- to threefold increases in actual run times using either graphical or central processing units of today. It is hoped that this argument will convince researchers to revisit certain numerical techniques that have long been shelved and reevaluate them for multicore usability.

  3. He 2++ molecular ion in a strong time-dependent magnetic field: a current-density functional study.

    Science.gov (United States)

    Vikas

    2011-08-01

    The He 2++ molecular ion exposed to a strong ultrashort time-dependent (TD) magnetic field of the order of 10(9) G is investigated through a quantum fluid dynamics (QFD) and current-density functional theory (CDFT) based approach using vector exchange-correlation (XC) potential and energy density functional that depend not only on the electronic charge-density but also on the current density. The TD-QFD-CDFT computations are performed in a parallel internuclear-axis and magnetic field-axis configuration at the field-free equilibrium internuclear separation R = 1.3 au with the field-strength varying between 0 and 10(11) G. The TD behavior of the exchange- and correlation energy of the He 2++ is analyzed and compared with that obtained using a [B-TD-QFD-density functional theory (DFT)] approach based on the conventional TD-DFT under similar computational constraints but using only scalar XC potential and energy density functional dependent on the electronic charge-density alone. The CDFT based approach yields TD exchange- and correlation energy and TD electronic charge-density significantly different from that obtained using the conventional TD-DFT based approach, particularly, at typical magnetic field strengths and during a typical time period of the TD field. This peculiar behavior of the CDFT-based approach is traced to the TD current-density dependent vector XC potential, which can induce nonadiabatic effects causing retardation of the oscillating electronic charge density. Such dissipative electron dynamics of the He 2++ molecular ion is elucidated by treating electronic charge density as an electron-"fluid" in the terminology of QFD.

  4. High current density PQQ-dependent alcohol and aldehyde dehydrogenase bioanodes.

    Science.gov (United States)

    Aquino Neto, Sidney; Hickey, David P; Milton, Ross D; De Andrade, Adalgisa R; Minteer, Shelley D

    2015-10-15

    In this paper, we explore the bioelectrooxidation of ethanol using pyrroloquinoline quinone (PQQ)-dependent alcohol and aldehyde dehydrogenase (ADH and AldDH) enzymes for biofuel cell applications. The bioanode architectures were designed with both direct electron transfer (DET) and mediated electron transfer (MET) mechanisms employing high surface area materials such as multi-walled carbon nanotubes (MWCNTs) and MWCNT-decorated gold nanoparticles, along with different immobilization techniques. Three different polymeric matrices were tested (tetrabutyl ammonium bromide (TBAB)-modified Nafion; octyl-modified linear polyethyleneimine (C8-LPEI); and cellulose) in the DET studies. The modified Nafion membrane provided the best electrical communication between enzymes and the electrode surface, with catalytic currents as high as 16.8 ± 2.1 µA cm(-2). Then, a series of ferrocene redox polymers were evaluated for MET. The redox polymer 1,1'-dimethylferrocene-modified linear polyethyleneimine (FcMe2-C3-LPEI) provided the best electrochemical response. Using this polymer, the electrochemical assays conducted in the presence of MWCNTs and MWCNTs-Au indicated a Jmax of 781 ± 59 µA cm(-2) and 925 ± 68 µA cm(-2), respectively. Overall, from the results obtained here, DET using the PQQ-dependent ADH and AldDH still lacks high current density, while the bioanodes that operate via MET employing ferrocene-modified LPEI redox polymers show efficient energy conversion capability in ethanol/air biofuel cells. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Probabilistic volcanic hazard assessments of Pyroclastic Density Currents: ongoing practices and future perspectives

    Science.gov (United States)

    Tierz, Pablo; Sandri, Laura; Ramona Stefanescu, Elena; Patra, Abani; Marzocchi, Warner; Costa, Antonio; Sulpizio, Roberto

    2014-05-01

    Explosive volcanoes and, especially, Pyroclastic Density Currents (PDCs) pose an enormous threat to populations living in the surroundings of volcanic areas. Difficulties in the modeling of PDCs are related to (i) very complex and stochastic physical processes, intrinsic to their occurrence, and (ii) to a lack of knowledge about how these processes actually form and evolve. This means that there are deep uncertainties (namely, of aleatory nature due to point (i) above, and of epistemic nature due to point (ii) above) associated to the study and forecast of PDCs. Consequently, the assessment of their hazard is better described in terms of probabilistic approaches rather than by deterministic ones. What is actually done to assess probabilistic hazard from PDCs is to couple deterministic simulators with statistical techniques that can, eventually, supply probabilities and inform about the uncertainties involved. In this work, some examples of both PDC numerical simulators (Energy Cone and TITAN2D) and uncertainty quantification techniques (Monte Carlo sampling -MC-, Polynomial Chaos Quadrature -PCQ- and Bayesian Linear Emulation -BLE-) are presented, and their advantages, limitations and future potential are underlined. The key point in choosing a specific method leans on the balance between its related computational cost, the physical reliability of the simulator and the pursued target of the hazard analysis (type of PDCs considered, time-scale selected for the analysis, particular guidelines received from decision-making agencies, etc.). Although current numerical and statistical techniques have brought important advances in probabilistic volcanic hazard assessment from PDCs, some of them may be further applicable to more sophisticated simulators. In addition, forthcoming improvements could be focused on three main multidisciplinary directions: 1) Validate the simulators frequently used (through comparison with PDC deposits and other simulators), 2) Decrease

  6. Current density distributions and sputter marks in electron cyclotron resonance ion sources.

    Science.gov (United States)

    Panitzsch, Lauri; Peleikis, Thies; Böttcher, Stephan; Stalder, Michael; Wimmer-Schweingruber, Robert F

    2013-01-01

    Most electron cyclotron resonance ion sources use hexapolar magnetic fields for the radial confinement of the plasma. The geometry of this magnetic structure is then--induced by charged particles--mapped onto the inner side of the plasma electrode via sputtering and deposition. The resulting structures usually show two different patterns: a sharp triangular one in the central region which in some cases is even sputtered deep into the material (referred to as thin groove or sharp structure), and a blurred but still triangular-like one in the surroundings (referred to as broad halo). Therefore, both patterns seem to have different sources. To investigate their origins we replaced the standard plasma electrode by a custom-built plasma electrode acting as a planar, multi-segment current-detector. For different biased disc voltages, detector positions, and source biases (referred to the detector) we measured the electrical current density distributions in the plane of the plasma electrode. The results show a strong and sharply confined electron population with triangular shape surrounded by less intense and spatially less confined ions. Observed sputter- and deposition marks are related to the analysis of the results. Our measurements suggest that the two different patterns (thin and broad) indeed originate from different particle populations. The thin structures seem to be caused by the hot electron population while the broad marks seem to stem from the medium to highly charged ions. In this paper we present our measurements together with theoretical considerations and substantiate the conclusions drawn above. The validity of these results is also discussed.

  7. Spatial profiles of interelectrode electron density in direct current superposed dual-frequency capacitively coupled plasmas

    Science.gov (United States)

    Ohya, Yoshinobu; Ishikawa, Kenji; Komuro, Tatsuya; Yamaguchi, Tsuyoshi; Takeda, Keigo; Kondo, Hiroki; Sekine, Makoto; Hori, Masaru

    2017-04-01

    We present experimentally determined spatial profiles of the interelectrode electron density (n e) in dual-frequency capacitively coupled plasmas in which the negative direct current (dc) bias voltage (V dc) is superposed; in the experiment, 13 MHz (P low) was applied to the lower electrode and 60 MHz (P high) to the upper electrode. The bulk n e increased substantially with increases in the external power, P high, P low, and with increases in V dc. When P low was insufficient, the bulk n e decreased as the V dc bias increased. The bulk n e increased due to its dependence on V dc, especially for |V dc|  >  500 V. This may correspond to the sheath voltages (V s) of the lower electrode. The n e values in front of the upper electrode were coupled with the V dc: the V dc dependence first decreased and then increased. The dc currents (I dc) of the upper electrode were collected when a large P low was applied. The value of I dc at the threshold value of V dc  ≈  V s (e.g.  ‑500 V) increased with an increase in n e. When |V dc| exceeded the threshold, the spatial n e profile and the I dc dependence were changed relative to the electrical characteristics of the dc superposition; this led to a change in the location of the maximum n e, the width of the area of n e depletion in front of the electrodes, and a transition in the electron heating modes.

  8. Quantification of mid and late evoked sinks in laminar current source density profiles of columns in the primary auditory cortex.

    Science.gov (United States)

    Schaefer, Markus K; Hechavarría, Julio C; Kössl, Manfred

    2015-01-01

    Current source density (CSD) analysis assesses spatiotemporal synaptic activations at somatic and/or dendritic levels in the form of depolarizing current sinks. Whereas many studies have focused on the short (primary auditory cortex of Mongolian gerbils. By applying an algorithm for contour calculation, three distinct mid and four late evoked sinks were identified in layers I, III, Va, VIa, and VIb. Our results further showed that the patterns of intracortical information-flow remained qualitatively similar for low and for high sound pressure level stimuli at the characteristic frequency (CF) as well as for stimuli ± 1 octave from CF. There were, however, differences associated with the strength, vertical extent, onset latency, and duration of the sinks for the four stimulation paradigms used. Stimuli one octave above the most sensitive frequency evoked a new, and quite reliable, sink in layer Va whereas low level stimulation led to the disappearance of the layer VIb sink. These data indicate the presence of input sources specifically activated in response to level and/or frequency parameters. Furthermore, spectral integration above vs. below the CF of neurons is asymmetric as illustrated by CSD profiles. These results are important because synaptic feedback associated with mid and late sinks-beginning at 50 ms post stimulus latency-is likely crucial for response modulation resulting from higher order processes like memory, learning or cognitive control.

  9. Maternal effects on male weaponry: female dung beetles produce major sons with longer horns when they perceive higher population density

    Directory of Open Access Journals (Sweden)

    Buzatto Bruno A

    2012-07-01

    Full Text Available Abstract Background Maternal effects are environmental influences on the phenotype of one individual that are due to the expression of genes in its mother, and are expected to evolve whenever females are better capable of assessing the environmental conditions that their offspring will experience than the offspring themselves. In the dung beetle Onthophagus taurus, conditional male dimorphism is associated with alternative reproductive tactics: majors fight and guard females whereas minors sneak copulations. Furthermore, variation in dung beetle population density has different fitness consequences for each male morph, and theory predicts that higher population density might select for a higher frequency of minors and/or greater expenditure on weaponry in majors. Because adult dung beetles provide offspring with all the nutritional resources for their development, maternal effects strongly influence male phenotype. Results Here we tested whether female O. taurus are capable of perceiving population density, and responding by changing the phenotype of their offspring. We found that mothers who were reared with other conspecifics in their pre-mating period produced major offspring that had longer horns across a wider range of body sizes than the major offspring of females that were reared in isolation in their pre-mating period. Moreover, our results indicate that this maternal effect on male weaponry does not operate through the amount of dung provided by females to their offspring, but is rather transmitted through egg or brood mass composition. Finally, although theory predicts that females experiencing higher density might produce more minor males, we found no support for this, rather the best fitting models were equivocal as to whether fewer or the same proportions of minors were produced. Conclusions Our study describes a new type of maternal effect in dung beetles, which probably allows females to respond to population density adaptively

  10. Influences of current density on tribological characteristics of ceramic coatings on ZK60 Mg alloy by plasma electrolytic oxidation.

    Science.gov (United States)

    Wu, Xiaohong; Su, Peibo; Jiang, Zhaohua; Meng, Song

    2010-03-01

    Current density is a key factor of plasma electrolytic oxidation process. Its influences on structure, mechanical, and tribological characteristics of ceramic coatings on ZK60 Mg alloy by pulsed bipolar microplasma oxidation in Na(3)PO(4) solution were studied in this paper. Thickness, structure, composition, mechanical property, and tribological characteristics of the coatings were studied by eddy current coating thickness gauge, scanning electron microscope (SEM), X-ray diffraction (XRD), nanoindentation measurements, and ball-on-disk friction testing. The results show that all the coatings prepared under different current densities are composed of MgO phase. The amount of MgO phase, thickness and friction coefficient of the coatings increased with the increasing current density. Among three ceramic coatings produced under three current densities, the coating produced under the current density of 7 A/dm(2) got the highest nanohardness and lowest wear rate with the value of 1.7 GPa and 1.27 x 10(-5) mm(3)/Nm.

  11. Enhancement in the critical current density of C-doped MgB2 wire using a polyacrylic acid dopant.

    Science.gov (United States)

    Lee, Seung Muk; Hwang, Soo Min; Lee, Chang Min; Kim, Won; Joo, Jinho; Lim, Jun Hyung; Kim, Chan-Joong; Hong, Gye-Won

    2012-02-01

    C-doped MgB2 wires were fabricated from a polyacrylic acid (PAA) using a conventional in-situ PIT technique. The effects of the PAA content on the lattice parameter, microstructure, critical temperature (Tc) and critical current density (Jc) were examined. With increasing PAA content, the amount of MgO in the sample increased but the crystallinity, a-axis lattice parameter, and Tc of MgB2 wires decreased, indicating that the C that decomposed from PAA during heat treatment had substituted for B. All doped samples exhibited a higher Jc than the undoped sample at high magnetic field, and the Jc(B) property improved with increasing PAA content: for the 7 wt% doped sample, the Jc was approximately 3-times higher than that of the pristine sample (1.28 kA/cm2 vs. 3.43 kA/cm2) at 5 K and 6.6 T. The improved Jc(B) of the doped sample was attributed to the decreased grain size, enlarged lattice distortion and increased C doping level.

  12. Sintering process and critical current density of low activation Mg11B2 superconductors from low temperature to high temperature

    Science.gov (United States)

    Cheng, Fang; Liu, Yongchang; Ma, Zongqing; Shahriar Al Hossain, Md; Somer, M.

    2016-08-01

    As the "low activation" superconductor, Mg11B2 has a potential application in superconducting coils for fusion reactor. In present work, the sintering process and critical current density of low activation Mg11B2 superconductors were systemically studied from low temperature to high temperature. It was found that the Jc and Hirr values of Mg11B2 bulks in present work are both obviously higher than that of those samples prepared in previous studies. Furthermore, the low-temperature sintered samples exhibit better Jc performance at high fields than the high-temperature sintered samples, due to strong grain boundaries pinning. On the other hand, the high-temperature sintered samples have higher Jc at low fields compared to low-temperature sintered samples, mainly owing to their better crystallinity and grain connectivity. The highest Jc value (2.20 ×105 A cm-2 at 20 K, self-field) is obtained in the Mg11B2 sample sintered at 850 °C for 45 min.

  13. Probability Density Function of the Output Current of Cascaded Multiplexer/Demultiplexers in Transparent Optical Networks

    Science.gov (United States)

    Rebola, João L.; Cartaxo, Adolfo V. T.

    The influence of the concatenation of arbitrary optical multiplexers/demultiplexers (MUX/DEMUXs) on the probability density function (PDF) of the output current of a transparent optical network is assessed. All PDF results obtained analytically are compared with estimates from Monte Carlo simulation and an excellent agreement is achieved. The non-Gaussian behavior of the PDFs, previously reported by other authors for square-law detectors, is significantly enhanced with the number of nodes increase due to the noise accumulation along the cascade of MUX/DEMUXs. The increase of the MUX/DEMUXs bandwidth and detuning also enhances the PDFs non-Gaussian behavior. The PDF shape variation with the detuning depends strongly on the number of nodes. Explanations for the Gaussian approximation (GA) accuracy on the assessment of the performance of a concatenation of optical MUX/DEMUXs are also provided. For infinite extinction ratio and tuned MUX/DEMUXs, the GA error probabilities are, in general, pessimistic, due to the inaccurate estimation of the error probability for both bits. For low extinction ratio, the GA is very accurate due to a balance between the error probabilities estimated for the bits "1" and "0." With the detuning increase, the GA estimates can become optimistic.

  14. High critical current densities in bulk MgB{sub 2} fabricated using amorphous boron

    Energy Technology Data Exchange (ETDEWEB)

    Muralidhar, Miryala; Kenta, Nozaki; Murakami, Masato [Superconducting Materials Laboratory, Department of Materials Science and Engineering, Shibaura Institute of Technology, Tokyo 135-8548 (Japan); Koblischka, Michael R. [Institute of Experimental Physics, Saarland University, P.O. Box 151150, 66041 Saarbruecken (Germany)

    2015-10-15

    We prepared bulk MgB{sub 2} from high-purity commercial powders of Mg metal (99.9% purity) and amorphous B (99% purity) powders using a single-step solid state reaction at 775 C for varying sintering duration from 1 to 10 h in pure argon atmosphere. X-ray diffraction analysis showed that all the samples were single phase MgB{sub 2}. The magnetization measurements confirmed a sharp superconducting transition with T{sub c,onset} at around 38.2-38.8 K. The critical current density (J{sub c}) values for the MgB{sub 2} samples produced at 1 h sintering time is the highest one in all processed materials here. Scanning electron microscopy analyses indicated that the sintering time has a crucial influence on the grain size. As a result, the highest J{sub c} value of 270 kA cm{sup -2} at 20 K and self-field was achieved in the sample produced at 775 C for 1 h. Our results clearly demonstrate that the optimization of the sintering conditions is essential to improve the bulk MgB{sub 2} performance. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  15. High Current Density, Long Life Cathodes for High Power RF Sources

    Energy Technology Data Exchange (ETDEWEB)

    Ives, Robert Lawrence [Calabazas Creek Research,, Inc.; Collins, George [Calabazas Creek Research, Inc.; Falce, Lou [Consultant; Schwartzkopf, Steve [Ron Witherspoon, Inc.; Busbaher, Daniel [Semicon Associates

    2014-01-22

    This program was tasked with improving the quality and expanding applications for Controlled Porosity Reservoir (CPR) cathodes. Calabazas Creek Research, Inc. (CCR) initially developed CPR cathodes on a DOE-funded SBIR program to improve cathodes for magnetron injection guns. Subsequent funding was received from the Defense Advanced Research Projects Agency. The program developed design requirements for implementation of the technology into high current density cathodes for high frequency applications. During Phase I of this program, CCR was awarded the prestigious 2011 R&D100 award for this technology. Subsequently, the technology was presented at numerous technical conferences. A patent was issued for the technology in 2009. These cathodes are now marketed by Semicon Associates, Inc. in Lexington, KY. They are the world’s largest producer of cathodes for vacuum electron devices. During this program, CCR teamed with Semicon Associates, Inc. and Ron Witherspoon, Inc. to improve the fabrication processes and expand applications for the cathodes. Specific fabrications issues included the quality of the wire winding that provides the basic structure and the sintering to bond the wires into a robust, cohesive structure. The program also developed improved techniques for integrating the resulting material into cathodes for electron guns.

  16. Morphological and optical properties of n-type porous silicon: effect of etching current density

    Indian Academy of Sciences (India)

    M DAS; D SARKAR

    2016-12-01

    Morphological and optical properties of porous silicon (PS) layer fabricated on n-type silicon wafer have been reported in the present article. Method of PS fabrication is by photo-assisted electrochemical etching with different etching current densities ($J$). Porosity and PS layer thickness, obtained by the gravimetric method, increase with increasing $J$. Pore morphology observed by FESEM shows the presence of randomly distributed pores with mostly spherical shape. Calculated pore size is also seen to increase with increasing value of $J$. XRD gives the characteristic amorphous peak of PS along with some peaks corresponding to crystalline silicon (c-Si). Calculated crystallite size shows decreasing trend with increasing $J$ value. The optical properties of these samples have been investigated by UV–visible reflectance, Raman spectroscopy and photoluminescence (PL) spectra. Reflectance measurement shows blue-shift of the spectrum with increased reflectivity for increasing $J$. Raman spectra show remarkable blue-shift with respect to the c-Si peak. PL spectra give the luminescence energy in the orange–red region of the visible spectrum and little change with variation of $J$.

  17. Minimax current density gradient coils: analysis of coil performance and heating.

    Science.gov (United States)

    Poole, Michael S; While, Peter T; Lopez, Hector Sanchez; Crozier, Stuart

    2012-08-01

    Standard gradient coils are designed by minimizing the inductance or resistance for an acceptable level of gradient field nonlinearity. Recently, a new method was proposed to minimize the maximum value of the current density in a coil additionally. The stated aim of that method was to increase the minimum wire spacing and to reduce the peak temperature in a coil for fixed efficiency. These claims are tested in this study with experimental measurements of magnetic field and temperature as well as simulations of the performance of many coils. Experimental results show a 90% increase in minimum wire spacing and 40% reduction in peak temperature for equal coil efficiency and field linearity. Simulations of many more coils indicate increase in minimum wire spacing of between 50 and 340% for the coils studied here. This method is shown to be able to increase coil efficiency when constrained by minimum wire spacing rather than switching times or total power dissipation. This increase in efficiency could be used to increase gradient strength, duty cycle, or buildability.

  18. Evaporation of metals by high-density (107 A · cm-2) electrical currents

    Science.gov (United States)

    Rakhel, A. D.

    1996-09-01

    In the present work, the problem of time evolution of pressure and temperature profiles across a wire through which an electrical current with a density of the order of 107 A · cm-2 flows is solved. The correct boundary conditions for a metal surface are obtained for the case when this metal is rapidly evaporated as a result of high-power Joule heating. The pressure profile appears under these conditions due to pinch-effect and inertia of thermal expansion of the metal; the temperature profile arises because of intensive evaporation from the surface of the wire. The conditions under which a liquid metal is superheated are formulated. On the basis of the analysis of the experimental results on exploding wires, the conclusion is drawn that decay of the metastable state takes place near the binodal. It is shown that the distribution of fine dispersed vapor bubbles is strongly nonuniform across the wire and the process of expansion of the two-phase mixture is very similar to the motion of a wave.

  19. Photoelectrolysis of water at high current density - Use of ultraviolet laser excitation

    Science.gov (United States)

    Bocarsly, A. B.; Bolts, J. M.; Cummins, P. G.; Wrighton, M. S.

    1977-01-01

    The behavior of TiO2 and SrTiO3 photoanodes in cells for the photoelectrolysis of H2O has been investigated for high-intensity 351-,364-nm excitation from an Ar ion laser. Intensities up to 380 W/sq cm have been used. For TiO2 a small amount of surface decomposition is found after irradiation at high intensity, whereas SrTiO3 undergoes no detectable changes. Current-voltage properties for both electrodes are essentially independent of light intensity up to the level of 380 W/sq cm, and there is little if any change in quantum efficiency for electron flow. Photocurrent densities have been shown to exceed 5 A/sq cm for O2 evolution. Data show that the energy storage rate associated with the SrTiO3 photoelectrolysis can exceed 30 W/sq cm; this represents the highest demonstrated rate of sustained optical-to-chemical energy conversion.

  20. Magnetic petrofabric of igneous rocks: Lessons from pyroclastic density current deposits and obsidians

    Science.gov (United States)

    Cañón-Tapia, E.; Mendoza-Borunda, R.

    2014-12-01

    Measurement of the anisotropy of magnetic susceptibility (AMS) of igneous rocks can provide clues concerning their mechanism of formation and in particular are very helpful as flow direction indicators. Unlike other igneous rocks, however, pyroclastic density current deposits (PDCDs) present a challenge in the interpretation of AMS measurements due to the complexity of their mechanism of emplacement. In this paper we review the most common assumptions made in the interpretation of the AMS of PDCD, taking advantage of key lessons obtained from obsidians. Despite the complexities on the mechanism of formation of PDCDs, it is shown that a key element for the fruitful interpretation of AMS is to give proper attention to the various components likely to be involved in controlling their general petrofabric. The anisotropies of ferromagnetic crystals (whether as free phases or embedded within clasts or shards), and those of paramagnetic minerals (mainly ferrosilicates) need to be taken into consideration when interpreting the AMS measurements of PDCDs. Variations of the deposition regime both as a function of position and of time also need to be considered on the interpretations. Nevertheless, if a suitable sampling strategy is adopted, the potential of the AMS method as a petrofabric indicator is maximized.

  1. High critical current density YBCO films and fabrication of dc-SQUIDs

    CERN Document Server

    Kuriki, S; Kawaguchi, Y; Matsuda, M; Otowa, T

    2002-01-01

    In order to improve the sensitivity of SQUID magnetometers made of high-T sub c films, we have studied the conditions of pulsed-laser deposition of YBCO films. Among the different deposition parameters examined, extensive degassing of the vacuum chamber before and precise control of the substrate temperature during the film deposition were found effective for obtaining high critical temperature T sub c and high critical current density J sub c. It was also found that the residual-resistance ratio has a clear correlation with J sub c , indicating that it can be a good, and easy to measure, index of the film quality. Films having T sub c approx 89-90 K and J sub c >= 5x10 sup 6 A cm sup - sup 2 at 77 K were used to fabricate SQUIDs without a pickup loop. Grain-boundary junctions formed on bicrystal substrates with a 30 deg. misorientation angle exhibited I sub c R sub n values of more than 100 mu V at 77 K. The well-known scaling behaviour of the relation I sub c R sub n propor to (J sup G sup B sub c) sup 1 su...

  2. Fracture behaviors of thin superconducting films with field-dependent critical current density

    Energy Technology Data Exchange (ETDEWEB)

    He, An; Xue, Cun; Yong, Huadong; Zhou, Youhe, E-mail: zhouyh@lzu.edu.cn

    2013-09-15

    Highlights: • The fracture behaviors of superconducting films for the Kim model are studied. • The profile of stress intensity factor is generally the same as magnetostriction. • The crack problem of two collinear cracks is also researched for the Kim model. -- Abstract: The fracture behaviors under electromagnetic force with field-dependent critical current density in thin superconducting film are investigated. Applying finite element method, the energy release rates and stress intensity factors of one central crack versus applied field and crack length are obtained for the Bean model and Kim model. It is interesting that the profile of the stress intensity factor is generally the same as the magnetostrictive behavior during one full cycle applied field. Furthermore, the crack problem of two collinear cracks with respect to crack length and distance is also researched for the Kim model. The results show that the energy release rates and stress intensity factors of the two collinear cracks at left tip and right tip are remarkably different for relatively small crack distance and long crack length. This work can offer good estimations and provide a basis for interpretation of cracking and mechanical failure of HTS thin films in numerous real situations.

  3. Field and temperature scaling of the critical current density in commercial REBCO coated conductors

    CERN Document Server

    Senatore, Carmine; Bonura, Marco; Kulich, Miloslav; Mondonico, Giorgio

    2016-01-01

    Scaling relations describing the electromagnetic behaviour of coated conductors (CCs) greatly simplify the design of REBCO-based devices. The performance of REBCO CCs is strongly influenced by fabrication route, conductor architecture and materials, and these parameters vary from one manufacturer to the others. In the present work we have examined the critical surface for the current density, Jc(T,B,θ ), of coated conductors from six different manufacturers: American Superconductor Co. (US), Bruker HTS GmbH (Germany), Fujikura Ltd. (Japan), SuNAM Co. Ltd. (Korea), SuperOx ZAO (Russia) and SuperPower Inc. (US). Electrical transport and magnetic measurements were performed at temperatures between 4.2 K and 77 K and in magnetic field up to 19 T. Experiments were conducted at three different orientations of the field with respect to the crystallographic c-axis of the REBCO layer, θ = 0deg , 45deg and 90deg , in order to probe the angular anisotropy of Jc. In spite of the large variability of CCs performance, ...

  4. Pyroclastic Density Current Hazards in the Auckland Volcanic Field, New Zealand

    Science.gov (United States)

    Brand, B. D.; Gravley, D.; Clarke, A. B.; Bloomberg, S. H.

    2012-12-01

    The most dangerous phenomena associated with phreatomagmatic eruptions are dilute pyroclastic density currents (PDCs). These are turbulent, ground-hugging sediment gravity currents that travel radially away from the explosive center at up to 100 m/s. The Auckland Volcanic Field (AVF), New Zealand, consists of approximately 50 eruptive centers, at least 39 of which have had explosive phreatomagmatic behaviour. A primary concern for future AVF eruptions is the impact of dilute PDCs in and around the Auckland area. We combine field observations from the Maungataketake tuff ring, which has one of the best exposures of dilute PDC deposits in the AVF, with a quantitative model for flow of and sedimentation from a radially-spreading, steady-state, depth-averaged dilute PDC (modified from Bursik and Woods, 1996 Bull Volcanol 58:175-193). The model allows us to explore the depositional mechanisms, macroscale current dynamics, and potential impact on societal infrastructure of dilute PDCs from a future AVF eruption. The lower portion of the Maungataketake tuff ring pyroclastic deposits contains trunks, limbs and fragments of Podocarp trees (strength of the wood, we calculate that dynamic pressures (Pdyn) of 10-75 kPa are necessary to topple trees of this size and composition. Thus the two main criteria for model success based on the field evidence include (a) Pdyn must be >10 kPa nearer than 0.9 km to the vent, and 35 kPa can be expected within 3 km from source, ensuring complete destruction of the area; Pdyn > 15 kPa up to 5 km from source, resulting in heavy structural damage to most buildings and near destruction of weaker buildings; and Pdyn <10 kPa at ~6 km from source, resulting in severe damage to weaker structures at least up to this distance. This exercise illustrates our ability to combine field measurements with numerical techniques to explore controlling parameters of dilute PDC dynamics. These tools can be used to understand and estimate the damage potential and

  5. Thermodynamics of sulfur poisoning in solid oxide fuel cells revisited: The effect of H2S concentration, temperature, current density and fuel utilization

    Science.gov (United States)

    da Silva, Aline Lima; Heck, Nestor Cezar

    2015-11-01

    Thermodynamics of sulfur poisoning in SOFCs is revisited in the present study, aiming at contributing to the understanding of the effects of different operating parameters on deactivation by sulfur. Ni-S Gibbs energy diagram shows that, whenever sulfur chemical potential is increased, the catalyst poisoning becomes greater, due to increase in nickel sulfide activity, which is a strictly increasing function of sulfur coverage on Ni surface. For studying current density effect, simulations are carried out in the range of 0 (OCV) - 1 A cm-2, at 1123 K, considering methane as a fuel. At 10 ppm H2S, an increase in current density from 0 (OCV) to 0.5 A cm-2 results in a slight increase in the nickel sulfide activity from 3.0 × 10-6 to 1.2 × 10-5; however, at 1 A cm-2, nickel sulfide activity is 25.000 times higher than at 0.5 A cm-2. At 1 A cm-2, H2 and CO are almost entirely converted to H2O and CO2 by electrochemical reaction. Therefore, the effect of current density becomes remarkable when fuel utilization approaches 100%. These theoretical findings are corroborated by the recent experimental evidences related to the detrimental influence of current density on SOFC performance during sulfur poisoning.

  6. A Study on Effects on Current Density Distribution, Inductance Gradient, and Contact Force by Variation of Armature and Rail Structure

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Bok Ki [Kwangwoon University, Seoul (Korea)

    2001-02-01

    The distribution of current in the conductors influenced by armature geometry and velocity is an important parameter for determining performance of an electromagnetic launcher(EML). The electric current in the early launching stage tends to flow on the outer surface of the conductors, resulting in very high local electric current density. However, the tendency for current to concentrate on the surface is driven by the velocity skin effect later in launching stage. The high current density produces high local heating and, consequently, increases armature wear which causes several defects on EML system. This paper investigates the effect of rail/armature geometry on current density distribution, launcher inductance gradient (L'), and contact force. Three geometrical parameters are used to characterize the railgun system. These are the ratio of contact length, relative position of contact leading edge to root trailing edge, and the ratio of rail overhang to the rail height. The distribution of current density, L',contact force between various configurations of the armature and the rail are analyzed and compared by using the EMAP3D program. (author). 6 refs., 9 figs., 3 tabs.

  7. Time-dependent density-functional theory simulation of local currents in pristine and single-defect zigzag graphene nanoribbons

    Science.gov (United States)

    He, Shenglai; Russakoff, Arthur; Li, Yonghui; Varga, Kálmán

    2016-07-01

    The spatial current distribution in H-terminated zigzag graphene nanoribbons (ZGNRs) under electrical bias is investigated using time-dependent density-functional theory solved on a real-space grid. A projected complex absorbing potential is used to minimize the effect of reflection at simulation cell boundary. The calculations show that the current flows mainly along the edge atoms in the hydrogen terminated pristine ZGNRs. When a vacancy is introduced to the ZGNRs, loop currents emerge at the ribbon edge due to electrons hopping between carbon atoms of the same sublattice. The loop currents hinder the flow of the edge current, explaining the poor electric conductance observed in recent experiments.

  8. Laboratory Study Of Magnetic Reconnection With A Density Asymmetry Across The Current Sheet

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Joseph; Yamada, Massaaki; Ji, Hantao; Meyers,, Clayton E.; Jara-Almonte,; Chen, Li-Jen

    2014-04-18

    The effects of an upstream density asymmetry on magnetic reconnection are studied systematically in a laboratory plasma. Despite a significant upstream density asymmetry of up to 10, the reconnecting magnetic field pro file is not signifi cantly changed. On the other hand, the out-of-plane magnetic field profile is considerably modified; it is almost bipolar in structure with the density asymmetry, as compared to the quadrupolar structure in the symmetric configuration. The in-plane ion flow pattern and the electrostatic potential pro file are also affected by the density asymmetry. Strong bulk electron heating is observed near the low-density-side separatrix together with electromagnetic fluctuations in the lower hybrid frequency range. The dependence of the ion outflow and reconnection electric field on the density asymmetry is measured and compared with theoretical expectations.

  9. Preliminary scaling laws for plasma current, ion kinetic temperature, and plasma number density in the NASA Lewis bumpy torus plasma

    Science.gov (United States)

    Roth, J. R.

    1976-01-01

    Parametric variation of independent variables which may affect the characteristics of bumpy torus plasma have identified those which have a significant effect on the plasma current, ion kinetic temperature, and plasma number density, and those which do not. Empirical power law correlations of the plasma current, and the ion kinetic temperature and number density were obtained as functions of potential applied to the midplane electrode rings, the background neutral gas pressure, and the magnetic field strength. Additional parameters studied included the type of gas, the polarity of the midplane electrode rings, the mode of plasma operation, and the method of measuring the plasma number density. No significant departures from the scaling laws appear to occur at the highest ion kinetic temperatures or number densities obtained to date.

  10. Volcán de Colima dome collapse of July, 2015 and associated pyroclastic density currents

    Science.gov (United States)

    Reyes-Dávila, Gabriel A.; Arámbula-Mendoza, Raúl; Espinasa-Pereña, Ramón; Pankhurst, Matthew J.; Navarro-Ochoa, Carlos; Savov, Ivan; Vargas-Bracamontes, Dulce M.; Cortés-Cortés, Abel; Gutiérrez-Martínez, Carlos; Valdés-González, Carlos; Domínguez-Reyes, Tonatiuh; González-Amezcua, Miguel; Martínez-Fierros, Alejandro; Ramírez-Vázquez, Carlos Ariel; Cárdenas-González, Lucio; Castañeda-Bastida, Elizabeth; Vázquez Espinoza de los Monteros, Diana M.; Nieto-Torres, Amiel; Campion, Robin; Courtois, Loic; Lee, Peter D.

    2016-06-01

    During July 10th-11th 2015, Volcán de Colima, Mexico, underwent its most intense eruptive phase since its Subplinian-Plinian 1913 AD eruption. Production of scoria coincident with elevated fumarolic activity and SO2 flux indicate a significant switch of upper-conduit dynamics compared with the preceding decades of dome building and vulcanian explosions. A marked increase in rockfall events and degassing activity was observed on the 8th and 9th of July. On the 10th at 20:16 h (Local time = UTM - 6 h) a partial collapse of the dome generated a series of pyroclastic density currents (PDCs) that lasted 52 min and reached 9.1 km to the south of the volcano. The PDCs were mostly channelized by the Montegrande and San Antonio ravines, and produced a deposit with an estimated volume of 2.4 × 106 m3. Nearly 16 h after the first collapse, a second and larger collapse occurred which lasted 1 h 47 min. This second collapse produced a series of PDCs along the same ravines, reaching a distance of 10.3 km. The total volume calculated for the PDCs of the second event is 8.0 × 106 m3. Including associated ashfall deposits, the two episodes produced a total of 14.2 × 106 m3 of fragmentary material. The collapses formed an amphitheater-shaped crater open towards the south. We propose that the dome collapse was triggered by arrival of gas-rich magma to the upper conduit, which then boiled-over and sustained the PDCs. A juvenile scoria sample selected from the second partial dome collapse contains hornblende, yet at an order of magnitude less abundant (0.2%) than that of 1913, and exhibits reaction rims, whereas the 1913 hornblende is unreacted. At present there is no compelling petrologic evidence for imminent end-cycle activity observed at Volcán de Colima.

  11. Early effect of NEURAPAS® balance on current source density (CSD of human EEG

    Directory of Open Access Journals (Sweden)

    Koch Klaus

    2011-08-01

    Full Text Available Abstract Psychiatric patients often suffer from stress, anxiety and depression. Various plant extracts are known to fight stress (valerian, anxiety (passion flower or depression (St. John's wort. NEURAPAS® balance is a mixture of these three extracts and has been designed to cover this complex of psychiatric conditions. The study was initiated to quantitatively assess the effect of this combination on brain electric activity. Method Quantitative electroencephalogram (EEG current source density (CSD recording from 16 healthy male and female human volunteers (average age 49 years was used in a randomized, placebo-controlled cross over study. Recordings were performed 0. 5, 1. 5, 3 and 4 hours after administration of the preparations under the conditions of 6 min eyes open and 5 min d2 concentration test, mathematical calculation test and memory test, respectively. All variables (electric power within 6 frequency ranges at 17 electrode positions were fed into a linear discriminant analysis (eyes open condition. In the presence of mental load these variables were used to construct brain maps of frequency changes. Results Under the condition of mental load, centro-parietal spectral power remained statistically significantly lower within alpha1, alpha2 and beta1 frequencies in the presence of verum in comparison to placebo. Discriminant analysis revealed a difference to placebo 3 and 4 hours after intake of 6 tablets of NEURAPAS® balance. Data location within the polydimensional space was projected into the area of the effects of sedative and anti-depressive reference drugs tested earlier under identical conditions. Results appeared closer to the effects of fluoxetine than to St. John's wort. Conclusions Analysis of the neurophysiological changes following the intake of NEURAPAS® balance revealed a similarity of frequency changes to those of calming and anti-depressive drugs on the EEG without impairment of cognition. Trial registration Clinical

  12. Localization of endocardial ectopic activity by means of noninvasive endocardial surface current density reconstruction

    Science.gov (United States)

    Lai, Dakun; Liu, Chenguang; Eggen, Michael D.; Iaizzo, Paul A.; He, Bin

    2011-07-01

    Localization of the source of cardiac ectopic activity has direct clinical benefits for determining the location of the corresponding ectopic focus. In this study, a recently developed current-density (CD)-based localization approach was experimentally evaluated in noninvasively localizing the origin of the cardiac ectopic activity from body-surface potential maps (BSPMs) in a well-controlled experimental setting. The cardiac ectopic activities were induced in four well-controlled intact pigs by single-site pacing at various sites within the left ventricle (LV). In each pacing study, the origin of the induced ectopic activity was localized by reconstructing the CD distribution on the endocardial surface of the LV from the measured BSPMs and compared with the estimated single moving dipole (SMD) solution and precise pacing site (PS). Over the 60 analyzed beats corresponding to ten pacing sites (six for each), the mean and standard deviation of the distance between the locations of maximum CD value and the corresponding PSs were 16.9 mm and 4.6 mm, respectively. In comparison, the averaged distance between the SMD locations and the corresponding PSs was slightly larger (18.4 ± 3.4 mm). The obtained CD distribution of activated sources extending from the stimulus site also showed high consistency with the endocardial potential maps estimated by a minimally invasive endocardial mapping system. The present experimental results suggest that the CD method is able to locate the approximate site of the origin of a cardiac ectopic activity, and that the distribution of the CD can portray the propagation of early activation of an ectopic beat.

  13. Influence of High-Current-Density Impulses on the Compression Behavior: Experiments with Iron and a Nickel-Based Alloy

    Science.gov (United States)

    Demler, E.; Gerstein, G.; Dalinger, A.; Epishin, A.; Rodman, D.; Nürnberger, F.

    2017-01-01

    Difficulties of processing of high strength and/or brittle materials by plastic deformation, e.g., by forging, require to develop new industrial technologies. In particular, the feasible deformation rates are limited for low-ductile metallic materials. For this reason, processes were investigated to improve the deformability in which electrical impulses are to be applied to lower the yield strength. However, owing to the impulse duration and low current densities, concomitant effects always occur, e.g., as a result of Joule heating. Current developments in power electronics allow now to transmit high currents as short pulses. By reducing the impulse duration and increasing the current density, the plasticity of metallic materials can be correspondingly increased. Using the examples of polycrystalline iron and a single-crystal, nickel-based alloy (PWA 1480), current advances in the development of methods for forming materials by means of high-current-density impulses are demonstrated. For this purpose, appropriate specimens were loaded in compression and, using novel testing equipment, subjected to a current strength of 10 kA with an impulse duration of 2 ms. For a pre-defined strain, the test results show a significant decrease in the compressive stress during the compression test and a significant change in the dislocation distribution following the current impulse treatment.

  14. New insights into aromatic pathways of carbachlorins and carbaporphyrins based on calculations of magnetically induced current densities.

    Science.gov (United States)

    Benkyi, Isaac; Fliegl, Heike; Valiev, Rashid R; Sundholm, Dage

    2016-04-28

    Magnetically induced current densities have been calculated and analyzed for a number of synthesized carbachlorins and carbaporphyrins using density functional theory and the gauge including magnetically induced current (GIMIC) method. Aromatic properties have been determined by using accurate numerical integration of the current flow yielding reliable current strengths and pathways that are related to the degree of aromaticity and the aromatic character of the studied molecules. All investigated compounds are found to be aromatic. However, the obtained aromatic pathways differ from those previously deduced from spectroscopic data and magnetic shielding calculations. For all studied compounds, the ring current divides into an outer and an inner branch at each pyrrolic subring, showing that all π-electrons of the pyrrolic rings take part in the delocalization pathway. The calculations do not support the common notion that the main share of the current takes the inner route at the pyrrolic rings without an inner hydrogen and follows an 18π aromatic pathway. The aromatic pathways of the investigated carbaporphyrins and carbachlorins are very similar, since the current strength via the Cβ[double bond, length as m-dash]Cβ' bond of the cyclopentadienyl ring of the carbaporphyrins is almost as weak as the current density passing the corresponding saturated Cβ-Cβ' bond of the carbachlorins.

  15. Influence of High-Current-Density Impulses on the Compression Behavior: Experiments with Iron and a Nickel-Based Alloy

    Science.gov (United States)

    Demler, E.; Gerstein, G.; Dalinger, A.; Epishin, A.; Rodman, D.; Nürnberger, F.

    2016-12-01

    Difficulties of processing of high strength and/or brittle materials by plastic deformation, e.g., by forging, require to develop new industrial technologies. In particular, the feasible deformation rates are limited for low-ductile metallic materials. For this reason, processes were investigated to improve the deformability in which electrical impulses are to be applied to lower the yield strength. However, owing to the impulse duration and low current densities, concomitant effects always occur, e.g., as a result of Joule heating. Current developments in power electronics allow now to transmit high currents as short pulses. By reducing the impulse duration and increasing the current density, the plasticity of metallic materials can be correspondingly increased. Using the examples of polycrystalline iron and a single-crystal, nickel-based alloy (PWA 1480), current advances in the development of methods for forming materials by means of high-current-density impulses are demonstrated. For this purpose, appropriate specimens were loaded in compression and, using novel testing equipment, subjected to a current strength of 10 kA with an impulse duration of 2 ms. For a pre-defined strain, the test results show a significant decrease in the compressive stress during the compression test and a significant change in the dislocation distribution following the current impulse treatment.

  16. The Current Situation and Future Prospects of International Relations in Japanese Higher Education Related Engineering Field

    Science.gov (United States)

    Taguchi, Shigenori

    With ongoing globalization, the role of higher education in developing excellent human resources who can play an active role in international society, among other things is becoming increasingly important. Recently, the international competition among higher education institutions to recruit the best and brightest students has been heating up increasingly. In this section, we present the outline of recent trend of internationalization in higher education with reference to policy of the Ministry of Education, Culture, Sports, Science and Technology (MEXT) .

  17. On the toroidal current density flowing across a poloidal-magnetic-field null in an axisymmetric plasma

    Science.gov (United States)

    Rodrigues, Paulo; Bizarro, João P. S.

    2013-04-01

    The axisymmetry condition and two of Maxwell's equations are used to show that, in general, there are no nested magnetic surfaces around a poloidal-magnetic-field null for a sufficiently small value of the toroidal current density flowing there. Hence, the toroidal current density at the axis of a magnetic configuration with extreme shear reversal cannot continuously approach zero unless nested surfaces are first broken or particular values are assigned to boundary conditions and other plasma parameters. The threshold of the toroidal current-density at which the topology changes is shown to be set by such parameters, and some examples of the predicted topology transition are presented using analytical solutions of the Grad-Shafranov equation.

  18. On the toroidal current density flowing across a poloidal-magnetic-field null in an axisymmetric plasma

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Paulo; Bizarro, Joao P. S. [Associacao Euratom-IST, Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, 1049-001 Lisboa (Portugal)

    2013-04-15

    The axisymmetry condition and two of Maxwell's equations are used to show that, in general, there are no nested magnetic surfaces around a poloidal-magnetic-field null for a sufficiently small value of the toroidal current density flowing there. Hence, the toroidal current density at the axis of a magnetic configuration with extreme shear reversal cannot continuously approach zero unless nested surfaces are first broken or particular values are assigned to boundary conditions and other plasma parameters. The threshold of the toroidal current-density at which the topology changes is shown to be set by such parameters, and some examples of the predicted topology transition are presented using analytical solutions of the Grad-Shafranov equation.

  19. Structural and phase transformations in zinc and brass wires under heating with high-density current pulse

    Science.gov (United States)

    Pervikov, A. V.

    2016-06-01

    The work is focused on revealing the mechanism of structure and phase transformations in the metal wires under heating with a high-density current pulse (the electric explosion of wires, EEWs). It has been demonstrated on the example of brass and zinc wires that the transition of a current pulse with the density of j ≈ 3.3 × 107 A/cm2 results in homogeneous heating of the crystalline structure of the metal/alloy. It has been determined that under heating with a pulse of high-density current pulse, the electric resistance of the liquid phases of zinc and brass decreases as the temperature increases. The results obtained allow for a conclusion that the presence of the particles of the condensed phase in the expanding products of EEW is the result of overheating instabilities in the liquid metal.

  20. High Current Density Effect on In-situ Atomic Migration Characteristics of a BiTe Thin Film System

    Science.gov (United States)

    Kim, Seunghyun; Park, Yong-Jin; Joo, Young-Chang; Park, Young-Bae

    2013-10-01

    Understanding fundamental atomic migration characteristics of multicomponent chalcogenide materials such as GeSbTe (GST) and BiTe are important in order to investigate the failure mechanism related to the electrical reliability of thermoelectric materials under high current density. In this work, high current density effect on the in-situ atomic migration characteristics of the BiTe thermoelectric thin films was conducted by real-time observation inside an scanning electron microscope chamber. Under the high current density conditions ranging from 0.83×106 to 1.0×106 A/cm2 at 100 °C, Te migrated toward the cathode, and Bi migrated toward the anode because the electrostatic force was dominant by very high Joule heating effect.

  1. The influence of post-growth thermal treatments on the critical current density of TSMG YBCO bulk superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Diko, P; Antal, V; Zmorayova, K; Sefcikova, M; Kovac, J [Institute of Experimental Physics SAS, Watsonova 47, 04001 Kosice (Slovakia); Chaud, X [CNRS/CRETA, 25, Avenue des Martyrs, 38042 Grenoble Cedex 9 (France); Yao, X [Department of Physics, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Chen, I [Department of Materials Science and Engineering, National Cheng Kung University (NCKU) Tainan, Taiwan (China); Eisterer, M; Weber, H W [Vienna University of Technology, Atominstitut, Stadionallee 2, 1020 Vienna (Austria)

    2010-12-15

    Oxygenation and thermochemical post-growth treatments of top seeded melt-growth (TSMG) YBCO bulk superconductors can significantly influence critical current density. It is shown that, depending on oxygenation conditions and the size of 211 particles, different reductions of intrinsic critical current density values can be obtained due to the reduction in the sample cross-section caused by the presence of a/b-microcracks induced by 211 particles, and a/b- and a/c-cracks induced by oxygenation. The possibility of eliminating oxygenation cracks by high pressure oxygenation and consequently significantly increasing the macroscopic critical current density is demonstrated. An effective dopant concentration for chemical pinning is proposed and possible clustering of substitutions in the Y123 lattice by thermochemical treatments is shown.

  2. Effect of Current Density on Thermodynamic Properties of Nanocrystalline Palladium Capped Samarium Hydride Thin Film Switchable Mirrors

    Directory of Open Access Journals (Sweden)

    Pushpendra Kumar

    2007-01-01

    Full Text Available A 55 nm samarium film capped with a 10 nm palladium overlayer switched from a metallic reflecting to a semiconducting, transparent in visible state during ex-situ hydrogen loading via electrochemical means in 1 M KOH electrolytic aqueous solution at room temperature. The switching between metal to semiconductor was accompanied by measurement of transmittance during hydrogen loading/unloading. The effect of current density on switching and thermodynamic properties was studied between dihydride state (FCC phase and trihydride state (hexagonal phase. From the plateau of partial pressure of hydrogen at x=2.6, enthalpy of formation was calculated at different current densities. The diffusion coefficients and switching kinetics are shown to depend on applied current density.

  3. Analysis of the magnetically induced current density of molecules consisting of annelated aromatic and antiaromatic hydrocarbon rings.

    Science.gov (United States)

    Sundholm, Dage; Berger, Raphael J F; Fliegl, Heike

    2016-06-21

    Magnetically induced current susceptibilities and current pathways have been calculated for molecules consisting of two pentalene groups annelated with a benzene (1) or naphthalene (2) moiety. Current strength susceptibilities have been obtained by numerically integrating separately the diatropic and paratropic contributions to the current flow passing planes through chosen bonds of the molecules. The current density calculations provide novel and unambiguous current pathways for the unusual molecules with annelated aromatic and antiaromatic hydrocarbon moieties. The calculations show that the benzene and naphthalene moieties annelated with two pentalene units as in molecules 1 and 2, respectively, are unexpectedly antiaromatic sustaining only a local paratropic ring current around the ring, whereas a weak diatropic current flows around the C-H moiety of the benzene ring. For 1 and 2, the individual five-membered rings of the pentalenes are antiaromatic and a slightly weaker semilocal paratropic current flows around the two pentalene rings. Molecules 1 and 2 do not sustain any net global ring current. The naphthalene moiety of the molecule consisting of a naphthalene annelated with two pentalene units (3) does not sustain any strong ring current that is typical for naphthalene. Instead, half of the diatropic current passing the naphthalene moiety forms a zig-zag pattern along the C-C bonds of the naphthalene moiety that are not shared with the pentalene moieties and one third of the current continues around the whole molecule partially cancelling the very strong paratropic semilocal ring current of the pentalenes. For molecule 3, the pentalene moieties and the individual five-membered rings of the pentalenes are more antiaromatic than for 1 and 2. The calculated current patterns elucidate why the compounds with formally [4n + 2] π-electrons have unusual aromatic properties violating the Hückel π-electron count rule. The current density calculations also provide

  4. Average OH density in alternating current dielectric barrier discharge by laser-induced fluorescence technique

    Science.gov (United States)

    Yang, Hongliang; Feng, Chunlei; Gao, Liang; Ding, Hongbin

    2015-10-01

    The average OH density in atmospheric He-H2O(0.4%) needle-plate dielectric barrier discharge (DBD) was measured by the asynchronous laser-induced fluorescence (LIF) technique and the fluctuation of OH radical density was measured simultaneously to prove that the average OH density can be obtained by the asynchronous LIF technique. The evolution of the average OH density in four different discharge patterns, namely, negative barrier corona discharge, glow discharge, multi glow discharge, and streamer discharge, was studied, and it was found that the average OH density has an observable increase from corona discharge to streamer discharge. The main mechanism of OH production in the four different discharge patterns was analyzed. It was shown that the main mechanism of OH production in negative barrier corona discharge is electron direct collision dissociation, whereas in the other three discharge patterns the He metastable Penning ionization is the main process.

  5. Self-field effects on critical current density and current-voltage characteristics in superconducting YBaCuO thick films

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez, A.D.; Hart, C.; Martinez, C.M.; Ares, O. [Superconductivity Lab, IMRE-University of Havana, Vedado 10400, Havana (Cuba)

    1999-07-01

    The self-field and percolative influences on transport measurements of polycrystalline bridges engraved on YBaCuO thick film have been investigated. A maximum in the dependence of the critical current density on cross-sectional area of the bridge (A = 0.003 mm{sup 2}-0.3 mm{sup 2}) has been found experimentally, in samples with low critical current densities (J{sub c}<50 A cm{sup -2}). The result of the measurements are in agreement with Mulet and coworkers, who have predicted that, under certain conditions, the self-field effects on transport measurements are negligible and the J{sub c} dependence on the sample dimensions is determined by the percolative character of the transport current. Self-field influences have also been observed in current-voltage characteristics, which have been analysed using the Ambegaokar-Halperin phase-slip theory. By allowing the noise parameter ({gamma}) to change with temperature, magnetic field and transport current, adequate agreement between theoretical and experimental current-voltage characteristics has been obtained. The dependence of the noise parameter with the transport current is demonstrated to be related with the self-field. (author)

  6. Critical current density behaviors across a grain boundary inclined to current with different angles in YBa2Cu3O7-δ bicrystal junctions

    Science.gov (United States)

    Tao, Hua; Wei-Wei, Xu; Zheng-Ming, Ji; Da-Yuan, Guo; Qing-Yun, Wang; Xiang-Rong, Ma; Rui-Yu, Liang

    2016-06-01

    The critical current density behaviors across a bicrystal grain boundary (GB) inclined to the current direction with different angles in YBa2Cu3O7-δ bicrystal junctions in magnetic fields are investigated. There are two main reasons for the difference in critical current density in junctions at different GB inclined angles in the same magnetic field: (i) the GB plane area determines the current carrying cross section; (ii) the vortex motion dynamics at the GB affects the critical current value when the vortex starts to move along the GB by Lorentz force. Furthermore, the vortex motion in a bicrystal GB is studied by investigating transverse (Hall) and longitudinal current-voltage characteristics (I-V xx and I-V xy ). It is found that the I-V xx curve diverges from linearity at a high driving current, while the I-V xy curve keeps nearly linear, which indicates the vortices inside the GB break out of the GB by Lorentz force. Project supported by the National Natural Science Foundation of China (Grant Nos. 61501222, 61371036, and 61571219) and the School Scientific Research Fund of Nanjing Institute of Technology, China (Grant Nos. YKJ201418).

  7. Update on Affirmative Action in Higher Education: A Current Legal Overview.

    Science.gov (United States)

    Springer, Ann

    This update reviews affirmative action cases in higher education in the context of the Supreme Court's recent decision to hear the Michigan affirmative action cases. The Supreme Court's decision on the Michigan cases will be the first Supreme Court opinion on affirmative action in higher education since "Bakke." Individual federal circuits and…

  8. The Current State and Developments in Higher Education in Gerontology in the Nordic Countries

    Science.gov (United States)

    Hietanen, Heidi; Lyyra, Tiina-Mari; Parkatti, Terttu; Heikkinen, Eino

    2012-01-01

    The growing size of the older population challenges not only researchers but also higher education in gerontology. On the basis of an online survey the authors describe the situation of Nordic higher education in gerontology in 2008 and 2009 and also give some good examples of Nordic- and European-level collaboration. The survey results showed…

  9. Higher Education Distance Learning in Portugal--State of the Art and Current Policy Issues

    Science.gov (United States)

    Hasan, Abrar; Laaser, Wolfram

    2010-01-01

    The paper is based on a recent report given to the Portuguese Ministry of Science, Technology and Higher Education on "Reforming Higher Education Distance Learning in Portugal" (Hasan et. al. 2009). The report was grounded on on-site visits of leading Portuguese Universities, Polytechnics and Business Schools as well as on written…

  10. The Current State and Developments in Higher Education in Gerontology in the Nordic Countries

    Science.gov (United States)

    Hietanen, Heidi; Lyyra, Tiina-Mari; Parkatti, Terttu; Heikkinen, Eino

    2012-01-01

    The growing size of the older population challenges not only researchers but also higher education in gerontology. On the basis of an online survey the authors describe the situation of Nordic higher education in gerontology in 2008 and 2009 and also give some good examples of Nordic- and European-level collaboration. The survey results showed…

  11. Vital Signs: The Current State of African Americans in Higher Education.

    Science.gov (United States)

    Journal of Blacks in Higher Education, 2000

    2000-01-01

    Presents a statistical record of the progress of African Americans in higher education, offering: the Black-White Higher Education Equality Index; statistics that measure racial inequality; states in which black college enrollments are expected to grow over the next 15 years; and differences among the states in their percentages of low-income…

  12. Benchmarking in European Higher Education: A Step beyond Current Quality Models

    Science.gov (United States)

    Burquel, Nadine; van Vught, Frans

    2010-01-01

    This paper presents the findings of a two-year EU-funded project (DG Education and Culture) "Benchmarking in European Higher Education", carried out from 2006 to 2008 by a consortium led by the European Centre for Strategic Management of Universities (ESMU), with the Centre for Higher Education Development, UNESCO-CEPES, and the…

  13. Bullying and Cyber-Bullying in Higher Education: Current Institutional Practice and Prevention

    Science.gov (United States)

    Early, Jeremy Scott

    2014-01-01

    Cyber-bullying led a Rutgers University student to commit suicide, which led the Federal government and institutions of higher education to take a closer look at bullying and cyber-bullying on college campuses. Congress introduced the "Tyler Clementi Higher Education Anti-Harassment Act" (Tyler Clementi Act) that would require…

  14. Bullying and Cyber-Bullying in Higher Education: Current Institutional Practice and Prevention

    Science.gov (United States)

    Early, Jeremy Scott

    2014-01-01

    Cyber-bullying led a Rutgers University student to commit suicide, which led the Federal government and institutions of higher education to take a closer look at bullying and cyber-bullying on college campuses. Congress introduced the "Tyler Clementi Higher Education Anti-Harassment Act" (Tyler Clementi Act) that would require…

  15. Current Trends, Challenges and Prospects of Student Mobility in the African Higher Education Landscape

    Science.gov (United States)

    Woldegiorgis, Emnet Tadesse; Doevenspeck, Martin

    2015-01-01

    Since the 1990s, the development in the international dimension of higher education including student/scholar mobility, regional and international research networks and initiatives have brought new opportunities for African higher education to be incorporated in the global knowledge production and circulation processes. One of the instruments of…

  16. Short-circuit current density imaging of crystalline silicon solar cells via lock-in thermography: Robustness and simplifications

    Energy Technology Data Exchange (ETDEWEB)

    Fertig, Fabian, E-mail: fabian.fertig@ise.fraunhofer.de; Greulich, Johannes; Rein, Stefan [Fraunhofer Institute for Solar Energy Systems ISE, Heidenhofstr. 2, D-79110 Freiburg (Germany)

    2014-11-14

    Spatially resolved determination of solar cell parameters is beneficial for loss analysis and optimization of conversion efficiency. One key parameter that has been challenging to access by an imaging technique on solar cell level is short-circuit current density. This work discusses the robustness of a recently suggested approach to determine short-circuit current density spatially resolved based on a series of lock-in thermography images and options for a simplified image acquisition procedure. For an accurate result, one or two emissivity-corrected illuminated lock-in thermography images and one dark lock-in thermography image have to be recorded. The dark lock-in thermography image can be omitted if local shunts are negligible. Furthermore, it is shown that omitting the correction of lock-in thermography images for local emissivity variations only leads to minor distortions for standard silicon solar cells. Hence, adequate acquisition of one image only is sufficient to generate a meaningful map of short-circuit current density. Beyond that, this work illustrates the underlying physics of the recently proposed method and demonstrates its robustness concerning varying excitation conditions and locally increased series resistance. Experimentally gained short-circuit current density images are validated for monochromatic illumination in comparison to the reference method of light-beam induced current.

  17. Influence of Electrolyte Modulus on the Local Current Density at a Dendrite Tip on a Lithium Metal Electrode

    Energy Technology Data Exchange (ETDEWEB)

    Harry, KJ; Higa, K; Srinivasan, V; Balsara, NP

    2016-08-10

    Understanding and controlling the electrochemical deposition of lithium is imperative for the safe use of rechargeable batteries with a lithium metal anode. Solid block copolymer electrolyte membranes are known to enhance the stability of lithium metal anodes by mechanically suppressing the formation of lithium protrusions during battery charging. Time-resolved hard X-ray microtomography was used to monitor the internal structure of a symmetric lithium-polymer cell during galvanostatic polarization. The microtomography images were used to determine the local rate of lithium deposition, i.e. local current density, in the vicinity of a lithium globule growing through the electrolyte. Measurements of electrolyte displacement enabled estimation of local stresses in the electrolyte. At early times, the current density was maximized at the globule tip, as expected from simple current distribution arguments. At later times, the current density was maximized at the globule perimeter. We show that this phenomenon is related to the local stress fields that arise as the electrolyte is deformed. The local current density, normalized for the radius of curvature, decreases with increasing compressive stresses at the lithium-polymer interface. To our knowledge, our study provides the first direct measurement showing the influence of local mechanical stresses on the deposition kinetics at lithium metal electrodes.

  18. Stochastic dynamics of extended objects in driven systems: I. Higher-dimensional currents in the continuous setting

    Science.gov (United States)

    Catanzaro, Michael J.; Chernyak, Vladimir Y.; Klein, John R.

    2016-12-01

    The probability distributions, as well as the mean values of stochastic currents and fluxes, associated with a driven Langevin process, provide a good and topologically protected measure of how far a stochastic system is driven out of equilibrium. By viewing a Langevin process on a compact oriented manifold of arbitrary dimension m as a theory of a random vector field associated with the environment, we are able to consider stochastic motion of higher-dimensional objects, which allow new observables, called higher-dimensional currents, to be introduced. These higher dimensional currents arise by counting intersections of a k -dimensional trajectory, produced by a evolving (k - 1) -dimensional cycle, with a reference cross section, represented by a cycle of complimentary dimension (m - k) . We further express the mean fluxes in terms of the solutions of the Supersymmetric Fokker-Planck (SFP), thus generalizing the corresponding well-known expressions for the conventional currents.

  19. Stochastic Dynamics of Extended Objects in Driven Systems: I. Higher-Dimensional Currents in the Continuous Setting

    CERN Document Server

    Catanzaro, Michael J; Klein, John R

    2016-01-01

    The probability distributions, as well as the mean values of stochastic currents and fluxes, associated with a driven Langevin process, provide a good and topologically protected measure of how far a stochastic system is driven out of equilibrium. By viewing a Langevin process on a compact oriented manifold of arbitrary dimension m as a theory of a random vector field associated with the environment, we are able to consider stochastic motion of higher-dimensional objects, which allow new observables, called higher-dimensional currents, to be introduced. These higher dimensional currents arise by counting intersections of a k-dimensional trajectory, produced by a evolving (k-1)-dimensional cycle, with a reference cross section, represented by a cycle of complimentary dimension (m - k). We further express the mean fluxes in terms of the solutions of the Supersymmetric Fokker-Planck (SFP), thus generalizing the corresponding well-known expressions for the conventional currents.

  20. A new look at mobility metrics for pyroclastic density currents: collection, interpretation, and use

    Science.gov (United States)

    Ogburn, S. E.; Lopes, D.; Calder, E. S.

    2012-12-01

    Mitigation of risk associated with pyroclastic density currents (PDCs) depends upon accurate forecasting of possible flow paths, often using empirical models that rely on mobility metrics or the stochastic application of computational flow models. Mobility metrics often inform computational models, sometimes as direct model inputs (e.g. energy cone model), or as estimates for input parameters (e.g. basal friction parameter in TITAN2D). These mobility metrics are often compiled from PDCs at many volcanoes, generalized to reveal empirical constants, or sampled for use in probabilistic models. In practice, however, there are often inconsistencies in how mobility metrics have been collected, reported, and used. For instance, the runout of PDCs often varies depending on the method used (e.g. manually measured from a paper map, automated using GIS software); and the distance traveled by the center of mass of PDCs is rarely reported due to the difficulty in locating it. This work reexamines the way we measure, report, and analyze PDC mobility metrics. Several metrics, such as the Heim coefficient (height dropped/runout, H/L) and the proportionality of inundated area to volume (A∝V2/3) have been used successfully with PDC data (Sparks 1976; Nairn and Self 1977; Sheridan 1979; Hayashi and Self 1992; Calder et al. 1999; Widiwijayanti et al. 2008) in addition to the non-volcanic flows they were originally developed for. Other mobility metrics have been investigated by the debris avalanche community but have not yet been extensively applied to pyroclastic flows (e.g. the initial aspect ratio of collapsing pile). We investigate the relative merits and suitability of contrasting mobility metrics for different types of PDCs (e.g. dome-collapse pyroclastic flows, ash-cloud surges, pumice flows), and indicate certain circumstances under which each model performs optimally. We show that these metrics can be used (with varying success) to predict the runout of a PDC of given volume

  1. Catalysts for ultrahigh current density oxygen cathodes for space fuel cell applications

    Science.gov (United States)

    Tryk, Donald A.; Yeager, E.

    1992-01-01

    The objective was to identify promising electrocatalyst/support systems for oxygen cathodes capable of operating at ultrahigh current densities in alkaline fuel cells. Such cells will require operation at relatively high temperatures and O2 pressures. A number of materials were prepared, including Pb-Ru and Pb-Ir pyrochlores, RuO2 and Pt-doped RuO2, lithiated NiO and La-Ni perovskites. Several of these materials were prepared using techniques that had not been previously used to prepare them. Particularly interesting was the use of the alkaline solution technique to prepare Pt-doped and Pb-Ru pyrochlores in high area form. Also interesting was the use of the fusion (melt) method for preparing the Pb-Ru pyrochlore. Several of the materials were also deposited with platinum. Well-crystallized Pb2Ru2O(7-y) was used to fabricate very high performance O2 cathodes with good stability in room temperature KOH. This material was also found to be stable over a useful potential range at approx. 140 C in concentrated KOH. For some of the samples, fabrication of the gas-fed electrodes could not be fully optimized during this project period. Future work may be directed at this problem. Pyrochlores that were not well-crystallized were found to be unstable in alkaline solution. Very good O2 reduction performance and stability were observed with Pb2RuO(7-y) in a carbon-based gas-fed electrode with an anion-conducting membrane placed on the electrolyte side of the electrode. The performance came within a factor of about two of that observed without carbon. High area platinum and gold supported on several conductive metal oxide supports were examined. Only small improvements in O2 reduction performance at room temperature were observed for Pb2Ru2O(7-y) as a support because of the high intrinsic activity of the pyrochlore. In contrast, a large improvement was observed for Li-doped NiO as a support for Pt. Very poor performance was observed for Au deposited on Li-NiO at approx. 150 C

  2. The 2010 Pyroclastic Density Currents of Merapi Volcano, Central Java, Indonesia

    Science.gov (United States)

    Charbonnier, Sylvain; Germa, Aurelie; Connor, Chuck; Connor, Laura; Dixon, Tim; Komorowski, Jean-Christophe; Gertisser, Ralf; Lavigne, Franck; Preece, Katie

    2013-04-01

    The 2010 pyroclastic density currents (PDC) at Merapi present a rare opportunity to collect a uniquely detailed dataset of the source, extent, lateral variations and impact of various PDC deposits on a densely populated area. Using traditional volcanological field-based methods and multi-temporal dataset of high-resolution satellite imagery, a total of 23 PDC events have been recognized, including 5 main channeled flows, 15 overbank flows derived from overspill and re-channelization of the main PDCs into adjacent tributaries and two main surge events. The 2010 PDC deposits covered an area of ~22.3 km2, unequally distributed between valley-filling (6.9%), overbank (22.4%) and ash-cloud surge deposits (71.7%). Their total estimated volume is ~36.3×106 m3, with ~50.2% of this volume accounting for valley-filling deposits, 39.3% for overbank deposits and 10.5% for ash-cloud surge deposits. The internal architecture and facies variations of the 2010 PDC deposit were investigated using data collected from 30 stratigraphic sections measured after one rainy season of erosion. The results show that complex, local-scale variations in flow dynamics and deposit architectures are apparent and that the main factors that control the propagation of the main flows and their potential hazards for overbanking were driven by: (1) the rapid emplacement of several voluminous PDCs, associated with the steady infilling of the receiving landscape after the two first phases of the eruption; (2) longitudinal changes in channel capacity following increased sinuosity in the valley and decreased containment space; and (3) the effects of varying generation mechanisms (gravitational dome collapse, vertical or lateral dome explosions and column-collapse) and source materials involved during individual PDC forming events. Integration of these data into numerical simulations of the 3-5 November channeled and overbank PDCs using two well-established geophysical mass flow models, Titan2D and Volcflow

  3. Transient 3D numerical simulations of column collapse and pyroclastic density current scenarios at Vesuvius

    Science.gov (United States)

    Esposti Ongaro, T.; Neri, A.; Menconi, G.; de'Michieli Vitturi, M.; Marianelli, P.; Cavazzoni, C.; Erbacci, G.; Baxter, P. J.

    2008-12-01

    Numerical simulations of column collapse and pyroclastic density current (PDC) scenarios at Vesuvius were carried out using a transient 3D flow model based on multiphase transport laws. The model describes the dynamics of the collapse as well as the effects of the 3D topography of the volcano on PDC propagation. Source conditions refer to a medium-scale sub-Plinian event and consider a pressure-balanced jet. Simulation results provide new insights into the complex dynamics of these phenomena. In particular: 1) column collapse can be characterized by different regimes, from incipient collapse to partial or nearly total collapse, thus confirming the possibility of a transitional field of behaviour of the column characterized by the contemporaneous and/or intermittent occurrence of ash fallout and PDCs; 2) the collapse regime can be characterized by its fraction of eruptive mass reaching the ground and generating PDCs; 3) within the range of the investigated source conditions, the propagation and hazard potential of PDCs appear to be directly correlated with the flow-rate of the mass collapsing to the ground, rather than to the collapse height of the column (this finding is in contrast with predictions based on the energy-line concept, which simply correlates the PDC runout and kinetic energy with the collapse height of the column); 4) first-order values of hazard variables associated with PDCs (i.e., dynamic pressure, temperature, airborne ash concentration) can be derived from simulation results, thereby providing initial estimates for the quantification of damage scenarios; 5) for scenarios assuming a location of the central vent coinciding with that of the present Gran Cono, Mount Somma significantly influences the propagation of PDCs, largely reducing their propagation in the northern sector, and diverting mass toward the west and southeast, accentuating runouts and hazard variables for these sectors; 6) the 2D modelling approximation can force an artificial

  4. Linear and angular momentum of electromagnetic fields generated by an arbitrary distribution of charge and current densities at rest

    CERN Document Server

    Thidé, B; Then, H; Tamburini, F

    2010-01-01

    Starting from Stratton-Panofsky-Phillips-Jefimenko equations for the electric and magnetic fields generated by completely arbitrary charge and current density distributions at rest, we derive far-zone approximations for the fields, containing all components, dominant as well as sub-dominant. Using these approximate formulas, we derive general formulas for the total electromagnetic linear momentum and angular momentum, valid at large distances from arbitrary, non-moving charge and current sources.

  5. Ultrasound Current Source Density Imaging in live rabbit hearts using clinical intracardiac catheter

    Science.gov (United States)

    Li, Qian

    Ultrasound Current Source Density Imaging (UCSDI) is a noninvasive modality for mapping electrical activities in the body (brain and heart) in 4-dimensions (space + time). Conventional cardiac mapping technologies for guiding the radiofrequency ablation procedure for treatment of cardiac arrhythmias have certain limitations. UCSDI can potentially overcome these limitations and enhance the electrophysiology mapping of the heart. UCSDI exploits the acoustoelectric (AE) effect, an interaction between ultrasound pressure and electrical resistivity. When an ultrasound beam intersects a current path in a material, the local resistivity of the material is modulated by the ultrasonic pressure, and a change in voltage signal can be detected based on Ohm's Law. The degree of modulation is determined by the AE interaction constant K. K is a fundamental property of any type of material, and directly affects the amplitude of the AE signal detected in UCSDI. UCSDI requires detecting a small AE signal associated with electrocardiogram. So sensitivity becomes a major challenge for transferring UCSDI to the clinic. This dissertation will determine the limits of sensitivity and resolution for UCSDI, balancing the tradeoff between them by finding the optimal parameters for electrical cardiac mapping, and finally test the optimized system in a realistic setting. This work begins by describing a technique for measuring K, the AE interaction constant, in ionic solution and biological tissue, and reporting the value of K in excised rabbit cardiac tissue for the first time. K was found to be strongly dependent on concentration for the divalent salt CuSO4, but not for the monovalent salt NaCl, consistent with their different chemical properties. In the rabbit heart tissue, K was determined to be 0.041 +/- 0.012 %/MPa, similar to the measurement of K in physiologic saline: 0.034 +/- 0.003 %/MPa. Next, this dissertation investigates the sensitivity limit of UCSDI by quantifying the relation

  6. Studies of challenge in lower hybrid current drive capability at high density regime in experimental advanced superconducting tokamak

    Science.gov (United States)

    Ding, B. J.; Li, M. H.; Li, Y. C.; Wang, M.; Liu, F. K.; Shan, J. F.; Li, J. G.; Wan, B. N.; Wan

    2017-02-01

    Aiming at a fusion reactor, two issues must be solved for the lower hybrid current drive (LHCD), namely good lower hybrid wave (LHW)-plasma coupling and effective current drive at high density. For this goal, efforts have been made to improve LHW-plasma coupling and current drive capability at high density in experimental advanced superconducting tokamak (EAST). LHW-plasma coupling is improved by means of local gas puffing and gas puffing from the electron side is taken as a routine way for EAST to operate with LHCD. Studies of high density experiments suggest that low recycling and high lower hybrid (LH) frequency are preferred for LHCD experiments at high density, consistent with previous results in other machines. With the combination of 2.45 GHz and 4.6 GHz LH waves, a repeatable high confinement mode plasma with maximum density up to 19~\\text{m}-3$ was obtained by LHCD in EAST. In addition, in the first stage of LHCD cyclic operation, an alternative candidate for more economical fusion reactors has been demonstrated in EAST and further work will be continued.

  7. Influence of cathodic current density and mechanical stirring on the electrodeposition of Cu-Co alloys in citrate bath

    Directory of Open Access Journals (Sweden)

    Leandro Trinta de Farias

    2008-03-01

    Full Text Available Cathodic polarization curves of Cu-Co alloys were galvanostatically obtained on a platinum net, using electrolytes containing copper and cobalt sulfates, sodium citrate and boric acid (pH values ranging from 4.88 to 6.00, with different mechanical stirring conditions. In order to evaluate quantitatively the influence of the applied current density and the mechanical stirring on the cathodic efficiency, the alloy composition for the Cu-Co alloy deposition process, and the average deposition potential, an experimental central composite design 2² was employed, and three current density intervals (0.11 to 0.60, 0.50 to 1.98 and 2.44 to 9.94 mA.cm-2 were chosen from the polarization curves for this purpose. The results indicated that the current density (mainly in the range between 0.11 and 0.60 mA.cm-2 affected significantly all the studied variables. In the intermediate range (0.50 to 1.98 mA.cm-2, only the average potential was influenced by the current density. On the other hand, the mechanical stirring had a significant effect only on the copper content, for both the lowest (0.11 to 0.60 mA.cm-2 and the highest current density range (2.44 to 9.94 mA.cm-2. Indeed, in the last range, none of the studied deposition parameters presented significant influence on the studied variables, except for the copper content. This could probably be explained by the direct incorporation of Cu-Citrate complexes in the coating, which was enhanced at high current values.

  8. Estimation of critical current density and grain connectivity in superconducting MgB 2 bulk using Campbell’s method

    Science.gov (United States)

    Ni, B.; Morita, Y.; Liu, Z.; Liu, C.; Himeki, K.; Otabe, E. S.; Kiuchi, M.; Matsushita, T.

    2008-09-01

    Many recent reports on the critical current density ( Jc) in superconducting MgB 2 bulks indicated that improving the grain connectivity is important, since the obtained Jc values were generally much lower than those in other metallic superconductors and it was ascribed to the poor connectivity between grains in polycrystalline MgB 2. In this study, we focused on the estimation of the global critical current density, super-current path, grain connectivity and their relationships with the faults volume fraction in the MgB 2 bulks prepared by a modified PIT (powder in tube) method. Campbell’s method was applied for the purpose of obtaining the penetrating AC flux profile and the characteristic of AC magnetic field vs. penetration depth from the sample’s surface. A computer simulation on the penetrating AC flux profile in MgB 2 bulks with randomly distributed voids, oxidized grains and other faults was also carried out. Jc obtained by Campbell’s method turned out to be smaller than that obtained from the SQUID measurement, implying that the global super-current was reduced by the existence of various faults and the lack of the electrical connectivity. It was verified that the relationship between the global critical current characteristics and the faults contained in MgB 2 samples can be quantitatively clarified by comparing the simulated critical current densities and other factors with the experimental results.

  9. Current Density Distribution on the Perimeter of Waveguide Exciter Cylindrical Vibrator Conductor

    OpenAIRE

    Zakharia, Yosyp

    2010-01-01

    On ground of electrodynamic analysis the surface current distribution nonuniformity on the perimeter of waveguide-exciter cylindrical conductor is found. Considerable influence of current distribution nonuniformity on exciter input reactance is established. It is also showed, that the current distribution on the vibrator perimeter, for conductor radius no greater then 0,07 of waveguide cross section breadth, approximately uniform is.

  10. Huge Critical Current Density and Tailored Superconducting Anisotropy in SmFeAsO(0.8)F(0.15) by Low Density Columnar-Defect Incorporation

    Science.gov (United States)

    Welp, U.; Fang, L.; Jia, Y.; Mishra, V.; Chaparro, C.; Vlasko-Vlasov, V. K.; Koshelev, A. E.; Crabtree, G. W.; Zhu, S. F.; Zhigadlo, N. D.; Katrych, S.; Karpinski, J.; Kwok, W. K.

    2014-03-01

    SmFeAsO(0.8)F(0.15) is of great interest because it has the highest transition temperature of all the iron-based superconductors. We find that the introduction of a low density of correlated nano-scale defects enhances the critical current density up to 2 × 107A/cm2 at 5 K without any suppression in the high superconducting transition temperature of 50 K and amounting to 20 % of the theoretical depairing current density. We also observed a surprising reduction in the thermodynamic superconducting anisotropy from 8 to 4 upon irradiation. A model based on anisotropic electron scattering predicts that the superconducting anisotropy can be tailored via correlated defects in semi-metallic, fully gapped type II superconductors. - We acknowledge support by the Center for Emergent Superconductivity, an EFRC funded by the US DOE, Office of Basic Energy Sciences (LF, YJ, VM, AEK, WKK, GWC), by the DOE, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357 (CC, VKV, UW), by the EC Research Council project SuperIron (JK, SK), and by the Swiss National Science Foundation and the National Center of Competence in Research MaNEP (NDZ).

  11. Experimental investigation of the effect of titanium dioxide and barium titanate additives on DC transient currents in low density polyethylene

    DEFF Research Database (Denmark)

    Khalil, M.S; Henk, Peter O; Henriksen, Mogens

    1988-01-01

    The effect of titanium dioxide as a semiconductive additive and barium titanate as a highly polar additive on the DC transient currents in low-density polyethylene is investigated. Experiments were made using thick specimens under a high electric field (>25×106 V/m) and a constant temperature of 40...

  12. Unified analytical expressions for calculating resonant frequencies, transimpedances, and equivalent input noise current densities of tuned receiver front ends

    DEFF Research Database (Denmark)

    Liu, Qing Zhong

    1992-01-01

    Unified analytical expressions have been derived for calculating the resonant frequencies, transimpedance and equivalent input noise current densities of the four most widely used tuned optical receiver front ends built with FETs and p-i-n diodes. A more accurate FET model has been used to improve...

  13. Charge and current density profiles of a degenerate magnetized free-electron gas near a hard wall

    NARCIS (Netherlands)

    M.M. Kettenis; L.G. Suttorp

    1998-01-01

    The charge and current densities of a completely degenerate free-electron gas in a uniform magnetic field are found to have a damped oscillatory spatial dependence near a wall that is parallel to the magnetic field. For large distances from the wall the behaviour of the associated profile functions

  14. Syntrophic interactions between H2-scavenging and anode-respiring bacteria can improve current density in microbial electrochemical cells

    Science.gov (United States)

    High current density of 10.0-14.6 A/m2 and COD removal up to 96% were obtained in a microbial electrochemical cell (MEC) fed with digestate at hydraulic retention time (HRT) of 4d and 8d. Volatile fatty acids became undetectable in MEC effluent (HRT 8d), except for trivial acetat...

  15. Effect of the Electrolyte Temperature and the Current Density on a Layer Microhardness Generated by the Anodic Aluminium Oxidation

    Directory of Open Access Journals (Sweden)

    Emil Spišák

    2015-01-01

    Full Text Available The paper investigates the influence of the chemical composition and temperature of electrolyte, the oxidation time, voltage, and the current density on Vickers microhardness of aluminium oxide layers, at the same time. The layers were generated in the electrolytes with different concentrations of sulphuric and oxalic acids and surface current densities 1 A·dm−2, 3 A·dm−2, and 5 A·dm−2. The electrolyte temperature varied from −1.78°C to 45.78°C. The results have showed that while increasing the electrolyte temperature at the current density of 1 A·dm−2, the increase in the layer microhardness values is approximately by 66%. While simultaneously increasing the molar concentration of H2SO4 in the electrolyte, the growth rate of the microhardness value decreases. At the current density of 3 A·dm−2, by increasing the electrolyte temperature, a reduction in the microhardness of the generated layer occurs with the anodic oxidation time less than 25 min. The electrolyte temperature is not significant with the changing values of the layer microhardness at voltages less than 10.5 V.

  16. Effect of preionization, fluorine concentration, and current density on the discharge uniformity in F2 excimer laser gas mixtures

    NARCIS (Netherlands)

    Mathew, D.; Bastiaens, Hubertus M.J.; Boller, Klaus J.; Peters, P.J.M.

    2007-01-01

    The discharge homogeneity in F2-based excimer laser gas mixtures and its dependence on various key parameters, such as the degree of preionization, preionization delay time, F2 concentration and current density, is investigated in a small x-ray preionized discharge chamber. The spatial and temporal

  17. Debate on the ’90s Higher Education Act and the current university

    Directory of Open Access Journals (Sweden)

    Eduardo Sánchez Martínez

    2013-11-01

    Full Text Available The Higher Education Act now in force in Argentina, was from its beginning an argued and ideologically questioned law. Different sectors resisted this piece of legislation and the institutional changes it outlined for Higher Education, especially for universities. Today, almost two decades afterwards, questioning goes on and a lot of people plead for a change they consider of necessity. The following text conteins some reflections of the author set out in a public debate on the issue, organized by the rectorships of Universidad Nacional de Córdoba and Universidad Nacional de Río Cuarto, in October 2013.

  18. Renewing the Dutch economics syllabus for higher secondary education: educational reforms from past to current databases

    NARCIS (Netherlands)

    Rol, Menno

    2015-01-01

    Dutch secondary school economics education was never at rest. It currently finds itself once more in an interesting phase of transition. New developments of behavioural economics have been incorpo-rated into the exam subject matter while the deletion of Keynesian model making from the corpus

  19. Current Challenges for K-12 Dance Education and Development: Perspectives from Higher Education

    Science.gov (United States)

    Risner, Doug

    2007-01-01

    From an administrative perspective, this article investigates equity issues in dance education, and current challenges and opportunities for leadership in postsecondary dance programs involved in teacher education and certification. Although dance education is varied in content and environment, much is shared in terms of common goals for gender…

  20. Current State of the Art: Management of Higher Risk Myelodysplastic Syndromes.

    Science.gov (United States)

    Komrokji, Rami S

    2016-08-01

    The higher risk myelodysplastic syndrome (MDS) patients, defined by the International Prognostic Scoring System (IPSS) as intermediate-2 or high-risk groups, compromise a third of MDS patients who have an expected survival of less than 1.5 years. Our ability to better define higher risk MDS improved with the proposal of new clinical risk models such as the revised IPSS and by integration of molecular data, including somatic gene mutations. Allogeneic hematopoietic stem-cell transplantation (AHSCT) remains the only curative option. In higher risk MDS patients, proceeding early with AHSCT is associated with maximum survival gain. The decision to pursue AHSCT is individualized according to disease risk, comorbidities, and functional status. The role of therapy before AHSCT remains controversial, and the role of post-AHSCT maintenance is evolving. Hypomethylating agents are the only medications that alter the natural history of the disease. Azacitidine is the only drug reported to improve overall survival in higher risk MDS patients. Appropriate use and assessment of response is key for assuring patients benefit of such limited options. Treatment after failure of hypomethylating agents is an unmet need. The role of detectable somatic gene mutations in prognosis and tailoring therapy continue to emerge.

  1. Faculty Development for Advancing Community Engagement in Higher Education: Current Trends and Future Directions

    Science.gov (United States)

    Welch, Marshall; Plaxton-Moore, Star

    2017-01-01

    This research involved the conduct of a conceptual review of 28 refereed journal articles and a survey of campus centers for community engagement staff to identify salient features and trends of existing faculty development programming designed to advance service-learning and community engagement in higher education. Results of this investigation…

  2. Entrepreneurship Education in Malaysia's Public Institutions of Higher Learning--A Review of the Current Practices

    Science.gov (United States)

    Bin Yusoff, Mohd Nor Hakimin; Zainol, Fakhrul Anwar; Bin Ibrahim, Mohamed Dahlan

    2015-01-01

    The need for a practical and applicable model for entrepreneurial learning is becoming critical. In this study, we aimed to collect data related to entrepreneurship education practices by all institutes of higher learning (IHLs) in Malaysia as well as challenges faced, facilities, and supports offered by the universities. Given the important role…

  3. Trends and EIE higher education response to the current global technical challenges

    DEFF Research Database (Denmark)

    Poboroniuc, Marian; Livint, Gheorghe; Friesel, Anna

    2014-01-01

    The European Association for Education in Electrical and Information Engineering (EAEEIE) has been for 20 years and still is dedicated to supporting Electrical and Information Engineering (EIE) across Europe. Its new Strategic Alignment of Electrical and Information Engineering in European Higher...

  4. Adaptive or Transactional Leadership in Current Higher Education: A Brief Comparison

    Science.gov (United States)

    Khan, Natalie

    2017-01-01

    Higher education institutions operate in a complex environment that includes influence from external factors, new technologies for teaching and learning, globalization, and changing student demographics to name a few. Maneuvering such complexity and change requires a leadership strategy that is flexible and supportive. This paper reviews two…

  5. Effects of Globalisation on Higher Engineering Education in Germany--Current and Future Demands

    Science.gov (United States)

    Morace, Christophe; May, Dominik; Terkowsky, Claudius; Reynet, Olivier

    2017-01-01

    Germany is well known around the world for the strength of its economy, its industry and for the "German model" for higher engineering education based on developing technological skills at a very high level. In this article, we firstly describe the former and present model of engineering education in Germany in a context of the…

  6. New Directions for the Student Consumer Movement. Current Issues in Higher Education, 1978.

    Science.gov (United States)

    American Association for Higher Education, Washington, DC.

    Two papers on developments toward consumerism in higher education are included. In "Alternatives to Federal Regulation of Consumer Information," by Joan S. Stark and Patrick T. Terenzini, several questions are posed for considering alternative systems to help students obtain and use information for college choice: (1) Can meaningful…

  7. Strategies for Retrenchment: National, State, Institutional. Current Issues in Higher Education, No. 6, 1980.

    Science.gov (United States)

    American Association for Higher Education, Washington, DC.

    Strategies regarding retrenchment in higher education are examined in three papers and commentaries. In "Basing Public Policy on Student Achievement: A New Agenda Item," Francis Keppel recommends that the federal government undertake a program of acquiring data on student achievement in certain areas of the college curriculum to provide…

  8. An Introduction to Current Trends and Benefits of Mobile Wireless Technology Use in Higher Education

    Science.gov (United States)

    Kim, Sang Hyun; Mims, Clif; Holmes, Kerry P.

    2006-01-01

    The development of mobile wireless technologies has generated a considerable amount of excitement among practitioners and academics because it results in shifting the academic environment from traditional settings to mobile learning (m-learning) settings. Increasing numbers of institutions of higher education offer courses using mobile wireless…

  9. High Current, High Density Arc Plasma as a New Source for WiPAL

    Science.gov (United States)

    Waleffe, Roger; Endrizzi, Doug; Myers, Rachel; Wallace, John; Clark, Mike; Forest, Cary; WiPAL Team

    2016-10-01

    The Wisconsin Plasma Astrophysics Lab (WiPAL) has installed a new array of nineteen plasma sources (plasma guns) on its 3 m diameter, spherical vacuum vessel. Each gun is a cylindrical, molybdenum, washer-stabilized, arc plasma source. During discharge, the guns are maintained at 1.2 kA across 100 V for 10 ms by the gun power supply establishing a high density plasma. Each plasma source is fired independently allowing for adjustable plasma parameters, with densities varying between 1018 -1019 m-3 and electron temperatures of 5-15 eV. Measurements were characterized using a 16 tip Langmuir probe. The plasma source will be used as a background plasma for the magnetized coaxial plasma gun (MCPG), the Terrestrial Reconnection Experiment (TREX), and as the plasma source for a magnetic mirror experiment. Temperature, density, and confinement results will be presented. This work is supported by the DoE and the NSF.

  10. Argyrophil cell density in the oxyntic mucosa is higher in female than in male morbidly obese patients

    Energy Technology Data Exchange (ETDEWEB)

    Maksud, F.A.N. [Laboratório de Patologia Digestiva e Neuroendócrina, Faculdade de Medicina, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Faculdade de Medicina, Universidade Federal de Ouro Preto, Ouro Preto, MG (Brazil); Kakehasi, A.M. [Laboratório de Patologia Digestiva e Neuroendócrina, Faculdade de Medicina, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Barbosa, A.J.A. [Laboratório de Patologia Digestiva e Neuroendócrina, Faculdade de Medicina, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Instituto Alfa de Gastroenterologia, Belo Horizonte, MG (Brazil)

    2013-04-05

    Obesity is a multifactorial disorder often associated with many important diseases such as diabetes, hypertension and other metabolic syndrome conditions. Argyrophil cells represent almost the total population of endocrine cells of the human gastric mucosa and some reports have described changes of specific types of these cells in patients with obesity and metabolic syndrome. The present study was designed to evaluate the global population of argyrophil cells of the gastric mucosa of morbidly obese and dyspeptic non-obese patients. Gastric biopsies of antropyloric and oxyntic mucosa were obtained from 50 morbidly obese patients (BMI >40) and 50 non-obese patients (17 dyspeptic overweight and 33 lean individuals) and processed for histology and Grimelius staining for argyrophil cell demonstration. Argyrophil cell density in the oxyntic mucosa of morbidly obese patients was higher in female (238.68 ± 83.71 cells/mm{sup 2}) than in male patients (179.31 ± 85.96 cells/mm{sup 2}) and also higher in female (214.20 ± 50.38 cells/mm{sup 2}) than in male (141.90 ± 61.22 cells/mm{sup 2}) morbidly obese patients with metabolic syndrome (P = 0.01 and P = 0.02, respectively). In antropyloric mucosa, the main difference in argyrophil cell density was observed between female morbidly obese patients with (167.00 ± 69.30 cells/mm{sup 2}) and without (234.00 ± 69.54 cells/mm{sup 2}) metabolic syndrome (P = 0.001). In conclusion, the present results show that the number of gastric argyrophil cells could be under gender influence in patients with morbid obesity. In addition, gastric argyrophil cells seem to behave differently among female morbidly obese patients with and without metabolic syndrome.

  11. Enhancement of critical current density in fast neutron irradiated melt-textured YBa 2Cu 3O 7- x

    Science.gov (United States)

    Puźniak, R.; Wiśniewski, A.; Baran, M.; Szymczak, H.; Pingxiang, Zhang; Jingrong, Wang; Lian, Zhou; Pytel, K.; Pytel, B.

    The critical current density in melt-textured samples obtained by the powder melting process was determined from magnetization measurements. Linear dependence between the width of the hysteresis loop and sample size was observed for both unirradiated and irradiated samples. This indicates that the critical current is circulating through the whole sample and is not disconnected by weak links, even when a magnetic field is applied in the irradiated sample. After fast neutron irradiation with fluences from 5 × 10 16 to 6 × 10 17 n cm -2 ( E > 0.5 MeV), significant enhancement of the critical current density, jc, was observed. Critical current density, determined from magnetization measurements, for magnetic field perpendicular to the a-b plane, jcab, reaches - 10 5 A cm 42 at 77 K in 1 T. For H parallel to the a-b plane, jcc along the c-axis reaches 5 × 10 3 A cm -2. An increase in the anisotropy of the critical current was observed after fast neutron irradiation in the temperature range 60 - 80 K.

  12. Integrated and Inclusive Higher Education in Vladimir State University: Current State and Development Perspectives

    Directory of Open Access Journals (Sweden)

    Yegorov I.N.,

    2017-08-01

    Full Text Available The paper summarizes the many years of experience in methodological support and training at the Center of Professional Education for the Disabled and at the “Inclusive Education” Research and Educational Center of the Vladimir State University. At these centers the work is aimed at establishing a system of continuous higher inclusive education for persons with hearing and visual impairments. The paper focuses on the issues concerning the organization of educational process and the adaptation of learning materials for students with hearing and visual impairments; it addresses the problem of creating a system of academic support for students with disabilities and providing psychological and educational assistance to individuals with hearing and visual impairments in the system of higher education.

  13. Microstructural and crystallographic imperfections of MgB2 superconducting wire and their correlation with the critical current density

    Directory of Open Access Journals (Sweden)

    Mohammed Shahabuddin

    2014-01-01

    Full Text Available A comprehensive study of the effects of structural imperfections in MgB2 superconducting wire has been conducted. As the sintering temperature becomes lower, the structural imperfections of the MgB2 material are increased, as reflected by detailed X-ray refinement and the normal state resistivity. The crystalline imperfections, caused by lattice disorder, directly affect the impurity scattering between the π and σ bands of MgB2, resulting in a larger upper critical field. In addition, low sintering temperature keeps the grain size small, which leads to a strong enhancement of pinning, and thereby, enhanced critical current density. Owing to both the impurity scattering and the grain boundary pinning, the critical current density, irreversibility field, and upper critical field are enhanced. Residual voids or porosities obviously remain in the MgB2, however, even at low sintering temperature, and thus block current transport paths.

  14. Second-order solutions for random interfacial waves in N-layer density stratified fluid with steady uniform currents

    Institute of Scientific and Technical Information of China (English)

    Chen Xiao-Gang; Guo Zhi-Ping; Song Jin-Bao

    2008-01-01

    In the present paper,the random interfacial waves in N-layer density-stratified fluids moving at different steady uniform speeds are researched by using an expansion technique,and the second-order asymptotic solutions of the random displacements of the density interfaces and the associated velocity potentials in N-layer fluid are presented based on the small amplitude wave theory.The obtained results indicate that the wave-wave second-order nonlinear interactions of the wave components and the second-order nonlinear interactions between the waves and currents are described.As expected,the solutions include those derived by Chen(2006)as a special case where the steady uniform currents of the N-layer fluids are taken as zero,and the solutions also reduce to those obtained by Song(2005)for second-order solutions for random interracial waves with steady uniform currents if N=2.

  15. An experimental investigation of the dynamics of submarine leveed channel initiation as sediment-laden density currents experience sudden unconfinement

    Energy Technology Data Exchange (ETDEWEB)

    Rowland, Joel C [Los Alamos National Laboratory; Hilley, George E [STANFORD UNIV; Fildani, Andrea [CHEVRON ETC

    2009-01-01

    Leveed submarine channels play a critical role in the transfer of sediment from the upper continental slopes to interslope basins and ultimately deepwater settings. Despite a reasonable understanding of how these channels grow once established, how such channels initiate on previously unchannelized portions of the seafloor remains poorly understood. We conducted a series of experiments that elucidate the influence of excess density relative to flow velocity on the dynamics of, and depositional morphologies arising from, density currents undergoing sudden unconfinement across a sloped bed. Experimental currents transported only suspended sediment across a non-erodible substrate. Under flow conditions ranging from supercritical to subcritical (bulk Richardson numbers of 0.02 to 1.2) our experiments failed to produce deposits resembling or exhibiting the potential to evolve into self-formed leveed channels. In the absence of excess density, a submerged sediment-laden flow produced sharp crested lateral deposits bounding the margins of the flow for approximately a distance of two outlet widths down basin. These lateral deposits terminated in a centerline deposit that greatly exceeded marginal deposits in thickness. As excess density increased relative to the outlet velocity, the rate of lateral spreading of the flow increased relative to the downstream propagation of the density current, transitioning from a narrow flow aligned with the channel outlet to a broad radially expanding flow. Coincident with these changes in flow dynamics, the bounding lateral deposits extended for shorter distances, had lower, more poorly defined crests that were increasingly wider in separation than the initial outlet, and progressively became more oblong rather than linear. Based on our results, we conclude that leveed channels cannot initiate from sediment-laden density currents under strictly depositional conditions. Partial confinement of these currents appears to be necessary to

  16. Key processes shaping the current role and operation of higher education institutions in society

    Directory of Open Access Journals (Sweden)

    Piróg Danuta

    2016-03-01

    Full Text Available The concurrent processes of globalisation, computerisation, and integration shape and constantly modify developmental factors and generate multidirectional social changes. Among social life fields, one of them has been particularly sensitive to the impact of those processes and has remained in clear feedback relationship with them is education, including university-level education. This article aims to present some reflections on the key processes which influence the environment of higher education institutions’ activity and on what their impact specifically is. The factors taken into account include: the transformation of the political and economic system, integration with the European higher education area, the market shift of education, evolving social demands towards higher education institutions and society’s attitude towards work. As knowledge has become an asset largely affecting the quality of life of people and society, universities have changed their focus from searching for and exploring truth, good and beauty in the world towards becoming innovation centres, transferring knowledge as offering their educational services. In this article, those trends have been exemplified in relation to geography degree programmes, and shown through an evolution of the model of the university. Based on a review of the literature, it seems that the processes discussed also concern geography degree programmes, and the future operation of these programmes closely depends on whether they can maintain their care for high quality education coupled with genuine efforts to ensure the smooth transition of graduates into the labour market.

  17. Density- and viscosity-stratified gravity currents: Insight from laboratory experiments and implications for submarine flow deposits

    Science.gov (United States)

    Amy, L. A.; Peakall, J.; Talling, P. J.

    2005-08-01

    Vertical stratification of particle concentration is a common if not ubiquitous feature of submarine particulate gravity flows. To investigate the control of stratification on current behaviour, analogue stratified flows were studied using laboratory experiments. Stratified density currents were generated by releasing two-layer glycerol solutions into a tank of water. Flows were sustained for periods of tens of seconds and their velocity and concentration measured. In a set of experiments the strength of the initial density and viscosity stratification was increased by progressively varying the lower-layer concentration, CL. Two types of current were observed indicating two regimes of behaviour. Currents with a faster-moving high-concentration basal region that outran the upper layer were produced if CL < 75%. Above this critical value of CL, currents were formed with a relatively slow, high-concentration base that lagged behind the flow front. The observed transition in behaviour is interpreted to indicate a change from inertia- to viscosity-dominated flow with increasing concentration. The reduction in lower-layer velocity at high concentrations is explained by enhanced drag at low Reynolds numbers. Results show that vertical stratification produces longitudinal stratification in the currents. Furthermore, different vertical and temporal velocity and concentration profiles characterise the observed flow types. Implications for the deposit character of particle-laden currents are discussed and illustrated using examples from ancient turbidite systems.

  18. Cooling of Water in a Flask: Convection Currents in a Fluid with a Density Maximum

    Science.gov (United States)

    Velasco, S.; White, J. A.; Roman, F. L.

    2010-01-01

    The effect of density inversion on the convective flow of water in a spherical glass flask cooled with the help of an ice-water bath is shown. The experiment was carried out by temperature measurements (cooling curves) taken at three different heights along the vertical diameter of the flask. Flows inside the flask are visualized by seeding the…

  19. Cooling of Water in a Flask: Convection Currents in a Fluid with a Density Maximum

    Science.gov (United States)

    Velasco, S.; White, J. A.; Roman, F. L.

    2010-01-01

    The effect of density inversion on the convective flow of water in a spherical glass flask cooled with the help of an ice-water bath is shown. The experiment was carried out by temperature measurements (cooling curves) taken at three different heights along the vertical diameter of the flask. Flows inside the flask are visualized by seeding the…

  20. Enhancement in field emission current density of Ni nanoparticles embedded in thin silica matrix by swift heavy ion irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Debalaya; Patra, Rajkumar; Srivastava, P.; Ghosh, S., E-mail: santanu1@physics.iitd.ac.in [Nanostech Laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi 110016 (India); Kumar, H. [Nanostech Laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi 110016 (India); Instituto de Física, Universidade de São Paulo, USP, 05508-090 São Paulo, SP (Brazil); Kabiraj, D.; Avasthi, D. K. [Inter University Accelerator Centre, New Delhi 110067 (India); Vayalil, Sarathlal K.; Roth, S. V. [DESY, Petra III, Hamburg (Germany)

    2014-05-07

    The field emission (FE) properties of nickel nanoparticles embedded in thin silica matrix irradiated with 100 MeV Au{sup +7} ions at various fluences are studied here. A large increase in FE current density is observed in the irradiated films as compared to their as deposited counterpart. The dependence of FE properties on irradiation fluence is correlated with surface roughness, density of states of valence band and size distribution of nanoparticles as examined with atomic force microscope, X-ray photoelectron spectroscopy, and grazing incidence small angle x-ray scattering. A current density as high as 0.48 mA/cm{sup 2} at an applied field 15 V/μm has been found for the first time for planar field emitters in the film irradiated with fluence of 5.0 × 10{sup 13} ions/cm{sup 2}. This significant enhancement in the current density is attributed to an optimized size distribution along with highest surface roughness of the same. This new member of field emission family meets most of the requirements of cold cathodes for vacuum micro/nanoelectronic devices.