Thermodynamic systematics of oxides of americium, curium, and neighboring elements

International Nuclear Information System (INIS)

Morss, L.R.

1984-01-01

Recently-obtained calorimetric data on the sesquioxides and dioxides of americium and curium are summarized. These data are combined with other properties of the actinide elements to elucidate the stability relationships among these oxides and to predict the behavior of neighboring actinide oxides. 45 references, 4 figures, 5 tables

In vitro dissolution of curium oxide using a phagolysosomal simulant solvent system

International Nuclear Information System (INIS)

Helfinstine, S.Y.; Guilmette, R.A.; Schlapper, G.A.

1992-01-01

Detailed study of actinide oxide behavior in alveolar macrophages (AM) in vitro is limited because of the short life span of these cells in culture. We created an in vitro dissolution system that could mimic the acidic phagolysosomal environment for the actinide and be maintained for an indefinite period so that dissolution of more insoluble materials could be measured. The dissolution system for this investigation, consisting of nine different solutions of HCl and the chelating agent diethylenetriamine pentaacetate (DTPA) in distilled water, is called the phagolysosomal simulant solvent (PSS). In this system, both the pH and the amount of DTPA were varied. We could observe the effect of altering pH within a range of 4.0-6.0 (similar to that of the phagolysosome) and the effect of the molar ratio of DTPA to curium at 1000: 1, 100;1, or 10:1. We chose curium sesquioxide ( 244 Cm 2 O 3 ) to validate the PSS for actinide dissolution versus that occurring in AM in vitro because it dissolves significantly in less than 1 week. The polydisperse 244 Cm 2 O 3 aerosol was generated, collected on filters, resuspended, and added to the PSS solutions and to cultured canine AM. By comparing dissolution in the two systems directly, we hoped to arrive at an optimum PSS for future dissolution studies. PSS and cell culture samples were taken daily for 7 days after exposure and tested for the solubilized curium. The amount of soluble material was determined by ultracentrifugation to separate the insoluble CM 2 O 3 from the soluble curium in the PSS solutions and filtration for the cell-containing material. After separating the soluble and insoluble fractions, the samples were analyzed using alpha liquid scintillation counting. Time-dependent dissolution measurements from the PSS/AM showed that the CM 2 O 3 dissolution was similar for both the PSS solutions and the cultured AM. 13 refs., 4 tabs

Extraction separation of americium and curium. A review

International Nuclear Information System (INIS)

Petrzilova, H.

1976-11-01

A survey is given of extraction systems suitable for transplutonium element separation and preparation as well as for the practical application of their nuclear properties. Methods are discussed in detail of separating the actinide and the lanthanide fractions from fission and corrosion products and of separating americium from curium. The description is completed with flowsheets showing the separation of transplutonium elements from irradiated targets and waste solutions after spent fuel reprocessing. (L.K.)

Spectroscopic and redox properties of curium and californium ions in concentrated aqueous carbonate-bicarbonate media

International Nuclear Information System (INIS)

Hobart, D.E.; Varlashkin, P.G.; Samhoun, K.; Haire, R.G.; Peterson, J.R.

1983-01-01

Multimilligram quantities of trivalent curium-248 and californium-249 were investigated by absorption spectroscopy, cyclic voltammetry, and bulk solution electrolysis in concentrated aqueous carbonate-bicarbonate solution. Actinide concentrations between 10 -4 and 10 -2 M were studied in 2 M sodium carbonate and 5.5 M potassium carbonate solutions at pH values from 8 to 14. The solution absorption spectra of Cm(III) and Cf(III) in carbonate media are presented for the first time and compared to literature spectra of these species in noncomplexing aqueous solution. It was anticipated that carbonate complexation of the actinide ions could provide a sufficient negative shift in the formal potentials of the M(IV)/M(III) couples of Cm and Cf to permit the generation and stabilization of their tetravalent states in aqueous carbonate-bicarbonate medium. No conclusive evidence was found in the present work to indicate the existence of any higher oxidation states of curium or californium in carbonate solution. Some possible reasons for our inability to generate and detect oxidized species of curium and californium in this medium are discussed

Application of curium measurements for safeguarding at reprocessing plants. Study 1: High-level liquid waste and Study 2: Spent fuel assemblies and leached hulls

International Nuclear Information System (INIS)

Rinard, P.M.; Menlove, H.O.

1996-03-01

In large-scale reprocessing plants for spent fuel assemblies, the quantity of plutonium in the waste streams each year is large enough to be important for nuclear safeguards. The wastes are drums of leached hulls and cylinders of vitrified high-level liquid waste. The plutonium amounts in these wastes cannot be measured directly by a nondestructive assay (NDA) technique because the gamma rays emitted by plutonium are obscured by gamma rays from fission products, and the neutrons from spontaneous fissions are obscured by those from curium. The most practical NDA signal from the waste is the neutron emission from curium. A diversion of waste for its plutonium would also take a detectable amount of curium, so if the amount of curium in a waste stream is reduced, it can be inferred that there is also a reduced amount of plutonium. This report studies the feasibility of tracking the curium through a reprocessing plant with neutron measurements at key locations: spent fuel assemblies prior to shearing, the accountability tank after dissolution, drums of leached hulls after dissolution, and canisters of vitrified high-level waste after separation. Existing pertinent measurement techniques are reviewed, improvements are suggested, and new measurements are proposed. The authors integrate these curium measurements into a safeguards system

Determination of plutonium, americium and curium in the marine environment

International Nuclear Information System (INIS)

Grenaut, CLaude; Germain, Pierre; Miramand, Pierre.

1982-01-01

The method used in the Laboratory for plutonium, americium and curium determination in marine samples (water, sediments, animals, plants) is presented. It is a modification of a procedure based on adsorption on ion exchange resins developed by other authors. The preliminary preparation of the samples, the radiochemical procedures and electrodeposition are described so as to be used as a practical handbook [fr

Final report on the decontamination of the Curium Source Fabrication Facility

International Nuclear Information System (INIS)

Schaich, R.W.

1983-12-01

The Curium Source Fabrication Facility (CSFF) at Oak Ridge National Laboratory (ORNL) was decontaminated to acceptable contamination levels for maintenance activities, using standard decontamination techniques. Solid and liquid waste volumes were controlled to minimize discharges to the ORNL waste systems. This program required two years of decontamination effort at a total cost of approximately $700K. 5 references, 7 figures, 2 tables

Pretreatment of americium/curium solutions for vitrification

International Nuclear Information System (INIS)

Rudisill, T.S.

1996-01-01

Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to the heavy isotope programs at Oak Ridge National Laboratory. Prior to vitrification, an in-tank oxalate precipitation and a series of oxalic/nitric acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Pretreatment development experiments were performed to understand the behavior of the lanthanides and the metal impurities during the oxalate precipitation and properties of the precipitate slurry. The results of these experiments will be used to refine the target glass composition allowing optimization of the primary processing parameters and design of the solution transfer equipment

Electrochemistry of oxygen-free curium compounds in fused NaCl-2CsCl eutectic

International Nuclear Information System (INIS)

Osipenko, A.; Maershin, A.; Smolenski, V.; Novoselova, A.; Kormilitsyn, M.; Bychkov, A.

2010-01-01

This work presents the electrochemical study of Cm(III) in fused NaCl-2CsCl eutectic in the temperature range 823-1023 K. Transient electrochemical techniques such as cyclic, differential pulse and square wave voltammetry, and chronopotentiometry have been used in order to investigate the reduction mechanism of curium ions up to the metal. The results obtained show that the reduction reaction takes place in a single step Cm(III)+3e-bar →Cm(0). The diffusion coefficient of [CmCl 6 ] 3- complex ions was determined by cyclic voltammetry at different temperatures by applying the Berzins-Delahay equation. The validity of the Arrhenius law was also verified and the activation energy for diffusion was found to be 44.46 kJ/mol. The apparent standard electrode potential of the redox couple Cm(III)/Cm(0) was found by chronopotentiometry at several temperatures. The thermodynamic properties of curium trichloride have also been calculated.

National Low-Level Waste Management Program radionuclide report series. Volume 13, Curium-242

International Nuclear Information System (INIS)

Adams, J.P.

1995-08-01

This report, Volume 13 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of curium-242 ( 242 Cm). This report also includes discussions about waste types and forms in which 242 Cm can be found and 242 Cm behavior in the environment and in the human body

National Low-Level Waste Management Program radionuclide report series. Volume 13, Curium-242

Energy Technology Data Exchange (ETDEWEB)

Adams, J.P.

1995-08-01

This report, Volume 13 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of curium-242 ({sup 242}Cm). This report also includes discussions about waste types and forms in which {sup 242}Cm can be found and {sup 242}Cm behavior in the environment and in the human body.

Americium/Curium Vitrification Pilot Tests - Part II

International Nuclear Information System (INIS)

Marra, J.E.; Baich, M.A.; Fellinger, A.P.; Hardy, B.J.; Herman, D.T.; Jones, T.M.; Miller, C.B.; Miller, D.H.; Snyder, T. K.; Stone, M.E.

1998-05-01

Isotopes of americium (Am) and curium (Cm) were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. These highly radioactive and valuable isotopes have been stored in an SRS reprocessing facility for a number of years. Vitrification of this solution will allow the material to be more safely stored until it is transported to the DOE Oak Ridge Reservation for use in research and medical applications. A previous paper described operation results from the Am-Cm Melter 2A pilot system, a full-scale non-radioactive pilot facility. This paper presents the results from continued testing in the Pilot Facility and also describes efforts taken to look at alternative vitrification process operations and flowsheets designed to address the problems observed during melter 2A pilot testing

Development of analytical methods for the separation of plutonium, americium, curium and neptunium from environmental samples

Energy Technology Data Exchange (ETDEWEB)

Salminen, S.

2009-07-01

In this work, separation methods have been developed for the analysis of anthropogenic transuranium elements plutonium, americium, curium and neptunium from environmental samples contaminated by global nuclear weapons testing and the Chernobyl accident. The analytical methods utilized in this study are based on extraction chromatography. Highly varying atmospheric plutonium isotope concentrations and activity ratios were found at both Kurchatov (Kazakhstan), near the former Semipalatinsk test site, and Sodankylae (Finland). The origin of plutonium is almost impossible to identify at Kurchatov, since hundreds of nuclear tests were performed at the Semipalatinsk test site. In Sodankylae, plutonium in the surface air originated from nuclear weapons testing, conducted mostly by USSR and USA before the sampling year 1963. The variation in americium, curium and neptunium concentrations was great as well in peat samples collected in southern and central Finland in 1986 immediately after the Chernobyl accident. The main source of transuranium contamination in peats was from global nuclear test fallout, although there are wide regional differences in the fraction of Chernobyl-originated activity (of the total activity) for americium, curium and neptunium. The separation methods developed in this study yielded good chemical recovery for the elements investigated and adequately pure fractions for radiometric activity determination. The extraction chromatographic methods were faster compared to older methods based on ion exchange chromatography. In addition, extraction chromatography is a more environmentally friendly separation method than ion exchange, because less acidic waste solutions are produced during the analytical procedures. (orig.)

Quantitative determination of americium and curium in solutions using potassium tungstophosphate

International Nuclear Information System (INIS)

Chistyakov, V.M.; Baranov, A.A.; Erin, E.A.; Timoaeev, G.A.

1990-01-01

Two methods of americium (4) and curium (4) titration-replacement and redox ones - have been considered. According to the replacement method thorium nitrate solution was used as a titrant and the final point of titration was determined spectophotometrically. Using the method developed, on the basis of experimental data, the composition of thorium (4) complex with potassium tungstophosphate was determined. In case of the redox titration sodium nitrite was used, and the final titration point was indicated either spectrophotometrically or potentiometrically

Vitrification of F-area americium/curium: feasibility study and preliminary process recommendation

International Nuclear Information System (INIS)

Ramsey, W.G.; Miller, D.; Minichan, R.; Coleman, L.; Schumacher, R.; Hardy, B.; Jones, R.

1994-01-01

Work was performed to identify a process to vitrify the contents of F- canyon Tank 17.1. Tank 17.1 contains the majority of americium (Am) and curium (Cm) contained in the DOE Complex. Oak Ridge National Laboratory (ORNL) has made a formal request for this material as fuel for production of Cf252 and other transplutonium actinides. The Am and Cm (and associated lanthanide fission products) are currently in nitric acid solution. Transportation of the intensely radioactive Am/Cm in liquid form is not considered possible. As a result, the material will either be solidified and shipped to ORNL or discarded to the Tank Farm. Nuclear Materials Processing Technology (NMPT), therefore, requested Defense Waste Processing Technology (DWPT) to determine if the Tank 17.1 material could be vitrified, and if it was vitrified could the americium and curium be successfully recovered. Research was performed to determine if the Tank 17.1 contents could indeed be mixed with glass formers and vitrified. Additional studies identified critical process parameters such as heat loading, melter requirements, off-gas evolution, etc. Discussions with NMPT personnel were initiated to determine existing facilities where this work could be accomplished safely. A process has been identified which will convert the Am/Cm material into approximately 300kg of glass

Remote micro-encapsulation of curium-gold cermets

International Nuclear Information System (INIS)

Coops, M.S.; Voegele, A.L.; Hayes, W.N.; Sisson, D.H.

1980-01-01

A technique is described for fabricating minature, high-density capsules of curium-244 oxide contained in three concentric jackets of metallic gold (or silver), with the outer surface being free of alpha contamination. The completed capsules are right circular cylinders 0.2500-inch diameter and 0.125-inch tall, with each level of containment soldered (or brazed) closed. A typical capsule would contain approx. 70 mg of 244 Cm (5.7 Ci) mixed with 120 mg of gold powder in the form of a cermet wafer clad in three concentric, 0.010-inch thick, liquid tight jackets. This method of fabrication eliminates voids between the jackets and produces a minimum size, maximum density capsule. Cermet densities of 11.5 g/cc were obtained, with an overall density of 17.3 g/cc for the finished capsule

Americium-curium vitrification process development

International Nuclear Information System (INIS)

Fellinger, A.P.; Baich, M.A.; Hardy, B.J

1999-01-01

The successful demonstration of sequentially drying, calcining and vitrifying an oxalate slurry in the Drain Tube Test Stand (DTTS) vessel provided the process basis for testing on a larger scale in a cylindrical induction heated melter. A single processing issue, that of batch volume expansion, was encountered during the initial stage of testing. The increase in batch volume centered on a sintered frit cap and high temperature bubble formation. The formation of a sintered frit cap expansion was eliminated with the use of cullet. Volume expansions due to high temperature bubble formation (oxygen liberation from cerium reduction) were mitigated in the DTTS melter vessel through a vessel temperature profile that effectively separated the softening point of the glass cullet and the evolving oxygen from cerium reduction. An increased processing temperature of 1,470 C and a two hour hold time to find any remaining bubbles successfully reduced bubbles in the poured glass to an acceptable level. The success of the preliminary process demonstrations provided a workable process basis that was directly applicable to the newly installed Cylindrical Induction Melter (CIM) system, making the batch flowsheet the preferred option for vitrification of the americium-curium surrogate feed stream

Cleanex process: a versatile solvent extraction process for recovery and purification of lanthanides, americium, and curium

International Nuclear Information System (INIS)

Bigelow, J.E.; Collins, E.D.; King, L.J.

1979-01-01

At a concentration of 1 M in straight-chain hydrocarbon diluent, HDEHP will extract americium, curium, and other trivalent actinide and lanthanide elements from dilute acid or salt solutions. The solute is back-extracted with more concentrated acid, either nitric or hydrochloric. The process has been used in the continuous, countercurrent mode, but its greatest advantage arises in batch extractions where the excess acid can be titrated with NaOH to produce a final acidity of about 0.03 M. Under these conditions, 99% recovery can be achieved, usually in one stage. Cleanex was used on the 50-liter scale at the Transuranium Processing Plant at Oak Ridge for 12 years to provide a broad spectrum cleanup to transuranium elements before applying more sophisticated techniques for separating individual products. The process is also used routinely to recover excessive losses of curium and/or californium from plant waste streams. The solvent system is relatively resistant to radiation damage, being usable up to 200 W-h/liter

Safety analysis report for packaging (SARP) of the Oak Ridge National Laboratory. TRU curium shipping container

International Nuclear Information System (INIS)

Box, W.D.; Klima, B.B.; Seagren, R.D.; Shappert, L.B.; Aramayo, G.A.

1980-06-01

An analytical evaluation of the Oak Ridge National Laboratory Transuranium (TRU) Curium Shipping Container was made to demonstrate its compliance with the regulations governing offsite shipment of packages containing radioactive material. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the container complies with the applicable regulations

A time-resolved laser fluorescence spectroscopy (TRLFS) study of the interaction of trivalent actinides (curium(III)) with calcite

International Nuclear Information System (INIS)

Stumpf, Th.; Fanghaenel, Th.

2002-01-01

Cm(III) interaction with calcite was investigated in the trace concentration range. Two different Cm(III)/calcite sorption species were found. The first Cm(III) sorption species consists of a curium ion that is bonded onto the calcite surface. The second Cm(III) sorption species has lost its complete hydration sphere and is incorporated into the calcite bulk structure /1/. (orig.)

Americium/Curium Melter 2A Pilot Tests

International Nuclear Information System (INIS)

Smith, M.E.; Fellinger, A.P.; Jones, T.M.; Miller, C.B.; Miller, D.H.; Snyder, T.K.; Stone, M.E.; Witt, D.C.

1998-05-01

Isotopes of americium (Am) and curium (Cm) were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. These highly radioactive and valuable isotopes have been stored in an SRS reprocessing facility for a number of years. Vitrification of this solution will allow the material to be more safely stored until it is transported to the DOE Oak Ridge Reservation for use in research and medical applications. To this end, the Am/Cm Melter 2A pilot system, a full-scale non- radioactive pilot plant of the system to be installed at the reprocessing facility, was designed, constructed and tested. The full- scale pilot system has a frit and aqueous feed delivery system, a dual zone bushing melter, and an off-gas treatment system. The main items which were tested included the dual zone bushing melter, the drain tube with dual heating and cooling zones, glass compositions, and the off-gas system which used for the first time a film cooler/lower melter plenum. Most of the process and equipment were proven to function properly, but several problems were found which will need further work. A system description and a discussion of test results will be given

Co-ordination properties of diglycol-amide (DGA) to trivalent curium and lanthanides studied by XAS, XRD and XPS methods

International Nuclear Information System (INIS)

Yaita, T.; Hirata, M.; Narita, H.; Tachimori, S.; Yamamoto, H.; Edelstein, N.M.; Bucher, J.J.; Shuh, D.K.; Rao, L.

2001-01-01

Co-ordination properties of diglycol-amide (DGA) to trivalent curium and to the trivalent lanthanides were studied by the EXAFS, the XRD and the XPS methods. The structural determinations by both the crystal XRD and the solution EXAFS methods showed that the DGA co-ordinated to the trivalent lanthanide ion in a tridentate fashion: co-ordination of three oxygen atoms of each ligand to the metal ion. The bond distances of Er-O (carbonyl) and Er-O (ether) in the Er-DGA complex were 2.35 Angstrom, and 2.46 Angstrom, respectively, while the atom distances of Cm-O (carbonyl) and Cm-O (ether) in the Cm-DGA complex were 2.42 Angstrom and 3.94 Angstrom, respectively from the EXAFS data for the Cm-DGA complex. Accordingly, the DGA would behave only as a semi-tridentate in the co-ordination to trivalent curium in solution. We determined the valence band structures of the Er-DGA complex by the XPS in order to clarify the bond properties of the complex, and assigned the XPS spectrum by using the DV-DS molecular orbital calculation method. (authors)

Type B investigation report of curium-244 exposure at the ORNL TRU Facility, January 15, 1986

International Nuclear Information System (INIS)

Love, G.L.; Butler, H.M.; Duncan, D.T.; Oakes, T.W.

1986-04-01

This Type B Investigative Report provides an evaluation of relevant events and activities that led to, were a part of, or resulted from the release of curium-244 in the Building 7920 facility at ORNL in January 1986. Impacts have been evaluated with respect to employee exposures and the costs and loss of productivity resulting from increased bioassay analyses and activities of investigative committees. Management systems evaluated include (1) training of employees performing lab analyses, (2) adherence to procedures, and (3) response to unusual circumstances

Transmutation of americium and curium incorporated in zirconia-based host materials

International Nuclear Information System (INIS)

Raison, P.E.

2001-01-01

Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO 2 -ZrO 2 -Y 2 O 3 . It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO 2 content. The Cm 2 O 3 -ZrO 2 system was also investigated. It was found that at 25 mol% of CmO 1.5 , the Cm(III) stabilized zirconia in its cubic form (a = 5.21 ±0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO 1.5 , a pyrochlore oxide - Cm 2 Zr 2 O 7 - is formed (a = 10.63 ±0.02 Angstrom). (author)

Density of simulated americium/curium melter feed solution

International Nuclear Information System (INIS)

Rudisill, T.S.

1997-01-01

Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to Oak Ridge National Laboratory and use in heavy isotope production programs. Prior to vitrification, a series of in-tank oxalate precipitation and nitric/oxalic acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Following nitric acid dissolution and oxalate destruction, the solution will be denitrated and evaporated to a dissolved solids concentration of approximately 100 g/l (on an oxide basis). During the Am/Cm vitrification, an airlift will be used to supply the concentrated feed solution to a constant head tank which drains through a filter and an in-line orifice to the melter. Since the delivery system is sensitive to the physical properties of the feed, a simulated solution was prepared and used to measure the density as a function of temperature between 20 to 70 degrees C. The measured density decreased linearly at a rate of 0.0007 g/cm3/degree C from an average value of 1.2326 g/cm 3 at 20 degrees C to an average value of 1.1973g/cm 3 at 70 degrees C

Density of simulated americium/curium melter feed solution

Energy Technology Data Exchange (ETDEWEB)

Rudisill, T.S.

1997-09-22

Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to Oak Ridge National Laboratory and use in heavy isotope production programs. Prior to vitrification, a series of in-tank oxalate precipitation and nitric/oxalic acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Following nitric acid dissolution and oxalate destruction, the solution will be denitrated and evaporated to a dissolved solids concentration of approximately 100 g/l (on an oxide basis). During the Am/Cm vitrification, an airlift will be used to supply the concentrated feed solution to a constant head tank which drains through a filter and an in-line orifice to the melter. Since the delivery system is sensitive to the physical properties of the feed, a simulated solution was prepared and used to measure the density as a function of temperature between 20 to 70{degrees} C. The measured density decreased linearly at a rate of 0.0007 g/cm3/{degree} C from an average value of 1.2326 g/cm{sup 3} at 20{degrees} C to an average value of 1.1973g/cm{sup 3} at 70{degrees} C.

Gas-Phase Energetics of Actinide Oxides: An Assessment of Neutral and Cationic Monoxides and Dioxides from Thorium to Curium

Science.gov (United States)

Marçalo, Joaquim; Gibson, John K.

2009-09-01

An assessment of the gas-phase energetics of neutral and singly and doubly charged cationic actinide monoxides and dioxides of thorium, protactinium, uranium, neptunium, plutonium, americium, and curium is presented. A consistent set of metal-oxygen bond dissociation enthalpies, ionization energies, and enthalpies of formation, including new or revised values, is proposed, mainly based on recent experimental data and on correlations with the electronic energetics of the atoms or cations and with condensed-phase thermochemistry.

Transmutation of americium and curium incorporated in zirconia-based host materials

Energy Technology Data Exchange (ETDEWEB)

Raison, P.E. [CEA Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d' Etudes des Combustibles; Haire, R.G. [Oak Ridge National Lab., TN (United States)

2001-07-01

Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO{sub 2}-ZrO{sub 2}-Y{sub 2}O{sub 3}. It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO{sub 2} content. The Cm{sub 2}O{sub 3}-ZrO{sub 2} system was also investigated. It was found that at 25 mol% of CmO{sub 1.5}, the Cm(III) stabilized zirconia in its cubic form (a = 5.21 {+-}0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO{sub 1.5}, a pyrochlore oxide - Cm{sub 2}Zr{sub 2}O{sub 7} - is formed (a = 10.63 {+-}0.02 Angstrom). (author)

Determination of americium and curium using ion-exchange in the nitric-acid-methanol medium for environmental analysis

International Nuclear Information System (INIS)

Holm, E.; Fukai, R.

1976-01-01

While transplutonic elements are only slightly sorbed to anion exchangers from hydrochloric or nitric acid media, the presence of alcohol enhances the anionic exchange of these elements, especially in nitric and sulfuric solutions. In the present work a method has been developed for determining americium and curium in environmental samples, on the basis of the difference between the sorption characteristics to anion exchangers in the acid-methanol system of these transplutonic elements and those of plutonium, polonium and thorium. The method also permits us to perform sequential determination of plutonium, when necessary

The use of curium neutrons to verify plutonium in spent fuel and reprocessing wastes

International Nuclear Information System (INIS)

Miura, N.

1994-05-01

For safeguards verification of spent fuel, leached hulls, and reprocessing wastes, it is necessary to determine the plutonium content in these items. We have evaluated the use of passive neutron multiplicity counting to determine the plutonium content directly and also to measure the 240 Pu/ 244 Cm ratio for the indirect verification of the plutonium. Neutron multiplicity counting of the singles, doubles, and triples neutrons has been evaluated for measuring 240 Pu, 244 Cm, and 252 Cf. We have proposed a method to establish the plutonium to curium ratio using the hybrid k-edge densitometer x-ray fluorescence instrument plus a neutron coincidence counter for the reprocessing dissolver solution. This report presents the concepts, experimental results, and error estimates for typical spent fuel applications

The effect of temperature on the sorption of technetium, uranium, neptunium and curium on bentonite, tuff and granodiorite

International Nuclear Information System (INIS)

Baston, G.M.N.; Berry, J.A.; Brownsword, M.; Heath, T.G.; Ilett, D.J.; Tweed, C.J.; Yui, M.

1997-01-01

A study of the sorption of the radioelements technetium; uranium; neptunium; and curium onto geological materials has been carried out as part of the PNC program to increase confidence in the performance assessment for a high-level radioactive waste repository in Japan. Batch sorption experiments have been performed in order to study the sorption of the radioelements onto bentonite, tuff and granodiorite from equilibrated de-ionized water under strongly-reducing conditions at both room temperature and at 60 C. Mathematical modelling using the geochemical speciation program HARPHRQ in conjunction with the HATCHES database has been undertaken in order to interpret the experimental results

Determination of C0-60 in Cobalt Slugs and Slabs and Radionuclides in Curium Sampler Slugs L-Reactor Disassembly Basin

International Nuclear Information System (INIS)

Casella, V.R.

2004-01-01

Co-60 was historically produced in the SRS reactors. Cobalt slugs were irradiated in the early 1970s. Post-production, remaining cobalt slugs (including slab form) were consolidated for storage. There are approximately nine hundred cobalt slugs currently stored awaiting final disposition. These slugs had historically incomplete documentation for activity rates; therefore, assaying was required in order to determine their activity levels. Since the gamma dose rate from these slugs is extremely high, the most cost effective way to shield a source of this magnitude from personnel and the radiation detector was to use the basin water in which the slugs are stored as the shield. A sodium iodide gamma detector was placed above a specially designed air collimator assembly, so that slug was at least eight feet from the detector and was shielded by the basin water. Using a sodium iodide detector and multichannel analyzer system and an underwater collimator assembly, Co-60 concentrations we re determined for Disassembly Basin cobalt slugs and slabs and 18 curium sampler slugs. The total activity of all of the assayed slugs summed to 31,783 curies. From the Co-60 concentrations of the curium sampler slugs, the irradiation flux was determined for the known irradiation time. The amounts of Pu-238, 239, 240, 241, 242; Am-241, 243; and Cm-242, 244 produced were then obtained based on the original amount of Pu-239 irradiated

Behavior of americium, curium, and certain fission products in fluoride melts in the presence of s olid extraction agents

International Nuclear Information System (INIS)

Alekseev, V.A.; Klokman, V.R.; Morozova, Z.E.; Ziv, V.S.

1986-01-01

The authors consider the behavior of americium, curium, and certain fission products (europium, cerium, yttrium, and strontium) in fluoride and chlode-fluoride melts in the presence of nonisomorphous solid phases: calcium fluoride and lanthanum and zirconium oxides. It is shown that the trace components enter the solid calcium fluoride in a regular fashion only in the presence of an adequate amount of oxygen in the melt. The effect of oxygen on the coprecipitation with calcium fluoride occurs because oxygen compounds of the elements must be formed in the melt, and these are then coprecipitated with the calcium fluoride

Critical and subcritical mass calculations of curium-243 to -247 based on JENDL-3.2 for revision of ANSI/ANS-8.15

International Nuclear Information System (INIS)

Okuno, Hiroshi

2002-01-01

Critical and subcritical masses were calculated for a sphere of five curium isotopes from 243 Cm to 247 Cm in metal and in metal-water mixtures considering three reflector conditions: bare, with a water reflector or a stainless steel reflector. The calculation were made mainly with a combination of a continuous energy Monte Carlo neutron transport calculation code, MCNP, and the Japanese Evaluated Nuclear Data Library, JENDL-3.2. Other evaluated nuclear data files, ENDF/B-VI and JEF-2.2, were also applied to find differences in calculation results of the neutron multiplication factor originated from different nuclear data files. A large dependence on the evaluated nuclear data files was found in the calculation results: more than 10%Δk/k relative differences in the neutron multiplication factor for a homogeneous mixture of 243 Cm metal and water when JENDL-3.2 was replaced with ENDF/B-VI and JEF-2.2, respectively; and a 44% reduction in the critical mass by changing from JENDL-3.2 to ENDF/B-VI for 246 Cm metal. The present study supplied basic information to the ANSI/ANS-8.15 Working Group for revision of the standard for nuclear criticality control of special actinide elements. The new or revised values of the subcritical mass limits for curium isotopes accepted by the ANSI/ANS-8.15 Working Group were finally summarized. (author)

Interactions of Microbes found at Aespoe Underground Lab with Actinides such as Curium, Plutonium and Uranium

Energy Technology Data Exchange (ETDEWEB)

Moll, H.; Merroun, M.; Geipel, G.; Rossberg, A.; Hennig, C.; Selenska-Pobell , S.; Bernhard, G. [Forschungszentrum Dresden-Rossendorf e.V., Inst. fuer Radioc hemie, 01314 Dresden (Germany)]. e-mail: h.moll@fzd.de; Stumpf, Th. [Forschungszentru m Karlsruhe, Inst. fuer Nukleare Entsorgung, 76021 Karlsruhe (Germany)

2007-06-15

Sulfate-reducing bacteria (SRB) frequently occur in the deep granitic rock aquifers at the Aespoe Hard Rock Laboratory (Aespoe HRL), Sweden. The new SRB strain Desulfovibrio aespoeensis could be isolated. Results describing the basic interaction mechanisms of uranium, curium, and plutonium with cells of D. aespoeensis DSM 10631T will be presented. The interaction experiments with the actinides showed that the cells are able to remove all three actinides from the surrounding solution. The amount of removed actinide and the interaction mechanism varied among the different actinides. The main U(VI) removal occurred after the first 24 h. The contact time, pH and [U(VI)]initial influence the U removal efficiency. The presence of uranium caused a damaging of the cell membranes. TEM revealed an accumulation of U inside the bacterial cell. D. aespoeensis are able to form U(IV). A complex interaction mechanism takes place consisting of biosorption, bioreduction and bioaccumulation. In the case of {sup 242}Pu, solvent extractions, UV-vis- and XANES spectroscopy were used to determine the speciation of the Pu oxidation states. In the first step, the Pu(VI) and Pu(IV)-polymers are bound to the biomass. Solvent extractions showed that 97 % of the initially present Pu(VI) is reduced to Pu(V) due to the activity of the cells within the first 24 h. Most of the formed Pu(V) dissolves from the cell envelope back to the aqueous solution due to the weak complexing properties of this plutonium oxidation state. In the case of curium at a much lower metal concentration of 3x10{sup -7} M, a pure biosorption of Cm(III) on the cell envelope forming an inner-sphere surface complex most likely with organic phosphate groups was detected. To summarize, the strength of the interaction of D. aespoeensis with the selected actinides at pH 5 and actinide concentrations = 10 mg/L ([Cm] 0.07 mg/L) follows the pattern: Cm > U > Pu >> Np.

Subcellular distribution of curium in beagle liver

International Nuclear Information System (INIS)

Bruenger, F.W.; Grube, B.J.; Atherton, D.R.; Taylor, G.N.; Stevens, W.

1976-01-01

The subcellular distribution of curium ( 243 244 Cm) was studied in canine liver from 2 hr to 47 days after injection of 3 μCi 243 244 Cm/kg of body weight. The pattern of distribution for Cm was similar to other trivalent actinide elements studied previously (Am, Cf). Initially (2 hr), most of the nuclide was found in the cytosol and at least 90 percent was protein bound. About 70 percent of the Cm was bound to ferritin, approximately 5 percent was associated with a protein of MW approximately 200,000, and approximately 25 percent was found in the low-molecular-weight region (approximately 5000). The decrease in the Cm content of cytosol, nuclei, and microsomes coincided with an increase in the amount associated with mitochondria and lysosomes. The concentration of the Cm in the mitochondrial fraction was higher than it was in the lysosomal fraction at each time studied. In the mitochondrial fraction approximately 30 percent of the Cm was bound to membranous or granular material, and 70 percent was found in the soluble fraction. The Cm concentration initially associated with cell nuclei was high but had diminished to 20 percent of the 2 hr concentration by 20 days post injection (PI). The subcellular distribution of Cm in the liver of a dog which had received the same dose and was terminated because of severe liver damage was studied at 384 days PI. The liver weighed 130 g and contained approximately 30 percent of the injected Cm. In contrast, a normal liver weighs 280 g and at 2 hr PI contains approximately 40 percent of the injected dose. The subcellular distribution of Cm in this severely damaged liver differed from the pattern observed at earlier times after injection. The relative concentration of Cm in the cytosol was doubled; it was higher in the nuclei-debris fraction; and it was lower in the mitochondrial and lysosomal fractions when compared to earlier times

Critical and subcritical mass calculations of curium-243 to -247 based on JENDL-3.2 for revision of ANSI/ANS-8.15

Energy Technology Data Exchange (ETDEWEB)

Okuno, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kawasaki, Hiromitsu [CRC Solutions Corporation, Hitachinaka, Ibaraki (Japan)

2002-10-01

Critical and subcritical masses were calculated for a sphere of five curium isotopes from {sup 243}Cm to {sup 247}Cm in metal and in metal-water mixtures considering three reflector conditions: bare, with a water reflector or a stainless steel reflector. The calculation were made mainly with a combination of a continuous energy Monte Carlo neutron transport calculation code, MCNP, and the Japanese Evaluated Nuclear Data Library, JENDL-3.2. Other evaluated nuclear data files, ENDF/B-VI and JEF-2.2, were also applied to find differences in calculation results of the neutron multiplication factor originated from different nuclear data files. A large dependence on the evaluated nuclear data files was found in the calculation results: more than 10%{delta}k/k relative differences in the neutron multiplication factor for a homogeneous mixture of {sup 243}Cm metal and water when JENDL-3.2 was replaced with ENDF/B-VI and JEF-2.2, respectively; and a 44% reduction in the critical mass by changing from JENDL-3.2 to ENDF/B-VI for {sup 246}Cm metal. The present study supplied basic information to the ANSI/ANS-8.15 Working Group for revision of the standard for nuclear criticality control of special actinide elements. The new or revised values of the subcritical mass limits for curium isotopes accepted by the ANSI/ANS-8.15 Working Group were finally summarized. (author)

Experimental and in situ investigations on americium, curium and plutonium behaviour in marine benthic species: transfer from water or sediments

International Nuclear Information System (INIS)

Miramand, P.

1984-06-01

The tranfer of transuranic elements -americium, curium and plutonium- from the sediments containing them to some marine benthic species (endofauna and epifauna) was studied with a twofold approach - laboratory and in-situ investigation. The experimental investigations, divided into three parts, made it possible to specify concentration factors (F.C.), transfer factors (F.T.) and to understand the process involved for 5 benthic species. The result were refined by an in-situ study that brought new data on the marine distribution of the transuranic elements released by the La Hague plant. Finally, the localization of americium and plutonium in the tissues and cells of these species was determined by autoradiography [fr

48 CFR 1846.672 - Preparing DD Forms 250 and 250c.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Preparing DD Forms 250 and 250c. 1846.672 Section 1846.672 Federal Acquisition Regulations System NATIONAL AERONAUTICS AND SPACE... DD Forms 250 and 250c. ...

48 CFR 1846.673 - Distribution of DD Forms 250 and 250c.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Distribution of DD Forms... Reports 1846.673 Distribution of DD Forms 250 and 250c. (a) DD Forms 250 and 250c shall be distributed in accordance with installation procedures. (b) The contractor is responsible for distributing DD Forms 250 and...

21 CFR 250.250 - Hexachlorophene, as a component of drug and cosmetic products.

Science.gov (United States)

2010-04-01

... cosmetic products. 250.250 Section 250.250 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF... Requirements for Drugs and Cosmetics § 250.250 Hexachlorophene, as a component of drug and cosmetic products... cosmetic products has expanded widely in recent years. It is used in such products because of its...

Levels of 250Cf populated in the decay of 250Bk

International Nuclear Information System (INIS)

Uecke, J.W.

1975-06-01

The nuclide 250 Bk undergoes β-decay with a half-life of 3.2 h to 13.1 y 250 Cf. A study is undertaken of the excited states in 250 Cf populated by 250 Bk decay which results from the α-decay of 276d 254 Es. The general features of published level schemes for these nuclei are consistent with predictions of the Nilsson and collective models; however, there remain many undiscovered transitions and ambiguous or uncertain level assignments. In an attempt to confirm predictions of current theoretical models which account for nuclear level assignments in this nucleus, these gamma transitions and their levels have been studied. Twenty-eight new γ-rays were determined. The decay of 250 Bk is investigated primarily by high resolution gamma-ray singles spectrometry and supported in part by two-parameter gamma-gamma coincidence spectrometry. The equipment, comprised of a Ge(HP) and a large volume Ge(Li) detector, a 4096-channel two-parameter analyzer, and a PDP-8/e computer system, permitted significant improvement in sensitivity and accuracy over previous investigations on this nucleus. (11 figures, 2 tables) (U.S.)

Radiation-chemical behaviour of neptunium ions in nitric acid solutions in the presence of curium-244

International Nuclear Information System (INIS)

Frolova, L.M.; Frolov, A.A.; Vasil'ev, V.Ya.

1984-01-01

Radiation-chemical behaviour of neptunium ions in nitric acid solutions is studied under the action of intensive internal alpha-irradiation conditioned by curium nuclides. In 0.3-1.1 mol/l solutions of nitric acid radiation-chemical oxidation of neptunium (4) and reduction of neptunium (6) is obeyed to the first order law of reaction rate in respect to neptunium concentration. Effective constants of neptunium (4) oxidation rates and neptuniumi(6) reduction rates are not dependent on neptunium ion in1tial concentration and increase with a growth of a dose rate of alpha-irradiation of solution. In equilibrium only neptunium (5) and neptunium (6) are present in solutions with HNO 3 concentration less than 1 mol/l. In more concentrated solutions equilibrium between sexa-, penta- and tetravalent neptunium forms is established. Equilibrium concentrations of neptunium valent forms are not dependent on neptunium initial oxidation state under the same initial conditions (dose rate, neptunium concentration and acidity. It is shown form experimental data that under the action of alpha-irradiation neptunium (5) both is oxidated to neptunium (6) and is reduced to neptunium (4)

Thermodynamics of curium(III) in concentrated electrolyte solutions: formation of sulfate complexes in NaCl/Na2SO4 solutions

International Nuclear Information System (INIS)

Paviet, P.; Fanghaenel, T.; Klenze, R.; Kim, J.I.

1996-01-01

The formation of sulfate complexes of Curium in aqueous solutions is studied by time resolved laser fluorescence spectroscopy (TRLFS) at 25 C. The species Cm 3+ , Cm(SO 4 ) - , Cm(SO 4 ) - 2 and Cm(SO 4 ) 3- 3 are quantified spectroscopically in the trace concentration range by peak deconvolution of fluorescence emission spectra. The complex formation equilibria are measured in NaCl/ Na 2 SO 4 solutions of constant ionic strength (3 molal) as a function of the sulfate concentration. The stability constants of Cm(SO 4 ) + and Cm(SO 4 ) - 2 are determined to be log β 1 = 0.93±0.08 and log β 2 = 0.61±0.08, respectively. The complex Cm(SO 4 ) 3- 3 is found to be stable only at very high sulfate concentrations (above 1 molal) and therefore not considered for further evaluation. (orig.)

30 CFR 250.1000 - General requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false General requirements. 250.1000 Section 250.1000... OPERATIONS IN THE OUTER CONTINENTAL SHELF Pipelines and Pipeline Rights-of-Way § 250.1000 General....1001, must meet the requirements in §§ 250.1000 through 250.1008. (2) A pipeline right-of-way grant...

Transport of plutonium, americium, and curium from soils into plants by roots

International Nuclear Information System (INIS)

Pimpl, M.; Schuettelkopf, H.

1979-12-01

For assessing the dose from radionuclides in agricultural products by ingestion it is necessary to know the soil to plant transfer factors. The literature was entirely investigated, in order to judge the size of the soil to plant transfer factors. In total, 92 publications - from 1948 to 1978 -have been evaluated. As result, transfer factors from 10 -9 to 10 -3 have been found for Plutonium, and from 10 -6 to 1 for Americium. For Curium only few data are available in literature. The considerable variation of the measured transfer factors is based on the dependence of these transfer factors from the ion exchange capacity of soils, from the amount of organic materials, from the pH-value, and from the mode of contamination. There are, in any case, contradictory data, although there has been detected a dependence of the transfer factors from these parameters. Chelating agenst increase the transfer factors to approximately 1300. As well, fertilizers have an influence on the size of the transfer factors - however, the relationships have been scarcely investigated. The distribution of actinides within the individual parts of plants has been investigated. The highest concentrations are in the roots; in the plant parts above ground the concentration of actinides decreases considerably. The most inferior transfer factors were measured for the respective seed or fruits. The soil to plant transfer factors of actinides are more dependend on the age of the plants within one growing period. At the beginning of the period, the transfer factor is considerably higher than at the end of this period. With respect to plants with a growing period of several years, correlations are unknown. (orig.) [de

30 CFR 250.1201 - Definitions.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Definitions. 250.1201 Section 250.1201 Mineral... Security § 250.1201 Definitions. Terms not defined in this section have the meanings given in the... hydrocarbons attributable to one or more platforms, leases, units, or wells, in relation to the total...

7 CFR 250.2 - Administration.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Administration. 250.2 Section 250.2 Agriculture... TERRITORIES AND POSSESSIONS AND AREAS UNDER ITS JURISDICTION General § 250.2 Administration. (a) Delegation to FNS. Within the Department, FNS shall act on behalf of the Department in the administration of the...

7 CFR 250.19 - Reviews.

Science.gov (United States)

2010-01-01

... or review to determine the extent to which sales are to be disallowed, establish a claim, and/or... 7 Agriculture 4 2010-01-01 2010-01-01 false Reviews. 250.19 Section 250.19 Agriculture Regulations... TERRITORIES AND POSSESSIONS AND AREAS UNDER ITS JURISDICTION General Operating Provisions § 250.19 Reviews. (a...

30 CFR 250.1401 - Index table.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Index table. 250.1401 Section 250.1401 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Outer Continental Shelf (OCS) Civil Penalties § 250.1401 Index table. The following table is an index of the sections in this subpart: § 250.1401Table Definitions...

30 CFR 250.1008 - Reports.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Reports. 250.1008 Section 250.1008 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Pipelines and Pipeline Rights-of-Way § 250.1008 Reports. (a) The... lessee or right-of-way holder shall submit a report to the Regional Supervisor within 90 days after...

IceMap250—Automatic 250 m Sea Ice Extent Mapping Using MODIS Data

Directory of Open Access Journals (Sweden)

Charles Gignac

2017-01-01

Full Text Available The sea ice cover in the North evolves at a rapid rate. To adequately monitor this evolution, tools with high temporal and spatial resolution are needed. This paper presents IceMap250, an automatic sea ice extent mapping algorithm using MODIS reflective/emissive bands. Hybrid cloud-masking using both the MOD35 mask and a visibility mask, combined with downscaling of Bands 3–7 to 250 m, are utilized to delineate sea ice extent using a decision tree approach. IceMap250 was tested on scenes from the freeze-up, stable cover, and melt seasons in the Hudson Bay complex, in Northeastern Canada. IceMap250 first product is a daily composite sea ice presence map at 250 m. Validation based on comparisons with photo-interpreted ground-truth show the ability of the algorithm to achieve high classification accuracy, with kappa values systematically over 90%. IceMap250 second product is a weekly clear sky map that provides a synthesis of 7 days of daily composite maps. This map, produced using a majority filter, makes the sea ice presence map even more accurate by filtering out the effects of isolated classification errors. The synthesis maps show spatial consistency through time when compared to passive microwave and national ice services maps.

Dicty_cDB: VFK250 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available VF (Link to library) VFK250 (Link to dictyBase) - - - Contig-U13825-1 VFK250P (Link to Original site) VFK2...50F 647 VFK250Z 679 VFK250P 1306 - - Show VFK250 Library VF (Link to library) Clone ID VFK2...e URL http://dictycdb.biol.tsukuba.ac.jp/CSM/VF/VFK2-C/VFK250Q.Seq.d/ Representative seq. ID VFK2...50P (Link to Original site) Representative DNA sequence >VFK250 (VFK250Q) /CSM/VF/VFK2-C/VFK2...re E Sequences producing significant alignments: (bits) Value VFK250 (VFK250Q) /CSM/VF/VFK2-C/VFK250Q.Seq.d/

TAF(II)250: a transcription toolbox.

Science.gov (United States)

Wassarman, D A; Sauer, F

2001-08-01

Activation of RNA-polymerase-II-dependent transcription involves conversion of signals provided by gene-specific activator proteins into the synthesis of messenger RNA. This conversion requires dynamic structural changes in chromatin and assembly of general transcription factors (GTFs) and RNA polymerase II at core promoter sequence elements surrounding the transcription start site of genes. One hallmark of transcriptional activation is the interaction of DNA-bound activators with coactivators such as the TATA-box binding protein (TBP)-associated factors (TAF(II)s) within the GTF TFIID. TAF(II)250 possesses a variety of activities that are likely to contribute to the initial steps of RNA polymerase II transcription. TAF(II)250 is a scaffold for assembly of other TAF(II)s and TBP into TFIID, TAF(II)250 binds activators to recruit TFIID to particular promoters, TAF(II)250 regulates binding of TBP to DNA, TAF(II)250 binds core promoter initiator elements, TAF(II)250 binds acetylated lysine residues in core histones, and TAF(II)250 possesses protein kinase, ubiquitin-activating/conjugating and acetylase activities that modify histones and GTFs. We speculate that these activities achieve two goals--(1) they aid in positioning and stabilizing TFIID at particular promoters, and (2) they alter chromatin structure at the promoter to allow assembly of GTFs--and we propose a model for how TAF(II)250 converts activation signals into active transcription.

7 CFR 250.57 - Commodity schools.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Commodity schools. 250.57 Section 250.57 Agriculture... TERRITORIES AND POSSESSIONS AND AREAS UNDER ITS JURISDICTION National School Lunch Program (NSLP) and Other Child Nutrition Programs § 250.57 Commodity schools. (a) Categorization of commodity schools. Commodity...

31 CFR 250.3 - Voucher applications.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Voucher applications. 250.3 Section 250.3 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) FISCAL SERVICE... in 250.4 and returned to the Credit Accounting Branch with the relevant information and the...

7 CFR 250.21 - Civil rights.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Civil rights. 250.21 Section 250.21 Agriculture... TERRITORIES AND POSSESSIONS AND AREAS UNDER ITS JURISDICTION General Operating Provisions § 250.21 Civil... Department's nondiscrimination regulations (7 CFR parts 15, 15a, and 15b) and the FNS civil rights...

45 CFR 2541.250 - Program income.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 4 2010-10-01 2010-10-01 false Program income. 2541.250 Section 2541.250 Public... Post-Award Requirements § 2541.250 Program income. (a) General. Grantees are encouraged to earn income to defray program costs. Program income includes income from fees for services performed, from the...

30 CFR 250.1614 - Mud program.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Mud program. 250.1614 Section 250.1614 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1614 Mud program. (a) The quantities, characteristics, use, and testing of drilling mud and the related drilling procedures shall be designed and...

30 CFR 250.300 - Pollution prevention.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Pollution prevention. 250.300 Section 250.300... OPERATIONS IN THE OUTER CONTINENTAL SHELF Pollution Prevention and Control § 250.300 Pollution prevention. (a... pollution occurs as a result of operations conducted by or on behalf of the lessee and the pollution damages...

30 CFR 250.602 - Equipment movement.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Equipment movement. 250.602 Section 250.602... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Workover Operations § 250.602 Equipment movement. The movement of well-workover rigs and related equipment on and off a platform or from well to well on...

30 CFR 250.502 - Equipment movement.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Equipment movement. 250.502 Section 250.502... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Completion Operations § 250.502 Equipment movement. The movement of well-completion rigs and related equipment on and off a platform or from well to well...

30 CFR 250.504 - Hydrogen sulfide.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Hydrogen sulfide. 250.504 Section 250.504... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Completion Operations § 250.504 Hydrogen sulfide. When a well-completion operation is conducted in zones known to contain hydrogen sulfide (H2S) or in...

30 CFR 250.604 - Hydrogen sulfide.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Hydrogen sulfide. 250.604 Section 250.604... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Well-Workover Operations § 250.604 Hydrogen sulfide. When a well-workover operation is conducted in zones known to contain hydrogen sulfide (H2S) or in...

30 CFR 250.808 - Hydrogen sulfide.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Hydrogen sulfide. 250.808 Section 250.808... OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Production Safety Systems § 250.808 Hydrogen sulfide. Production operations in zones known to contain hydrogen sulfide (H2S) or in zones where the presence of H2S...

21 CFR 74.250 - Orange B.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Orange B. 74.250 Section 74.250 Food and Drugs... ADDITIVES SUBJECT TO CERTIFICATION Foods § 74.250 Orange B. (a) Identity. (1) The color additive Orange B is.... (2) The diluents in color additive mixtures for food use containing Orange B are limited to those...

Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

International Nuclear Information System (INIS)

Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z.; Gillow, J.B.; Francis, A.J.

2004-01-01

We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K d ) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N H 2 O ) and the degree of strength of ligand field (R E/M ) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K d of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K d , indicating that an exchange with Na + on the functional groups was involved in their sorption. The ΔN H 2 O (= 9 - N H 2 O ) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R E/M for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

Energy Technology Data Exchange (ETDEWEB)

Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z. [Advanced Science Research Center, Japan Atomic Energy Research Inst., Ibaraki (Japan); Gillow, J.B.; Francis, A.J. [Environmental Sciences Dept., Brookhaven National Lab., Upton, NY (United States)

2004-07-01

We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K{sub d}) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N{sub H{sub 2}O}) and the degree of strength of ligand field (R{sub E/M}) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K{sub d} of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K{sub d}, indicating that an exchange with Na{sup +} on the functional groups was involved in their sorption. The {delta}N{sub H{sub 2}O} (= 9 - N{sub H{sub 2}O}) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R{sub E/M} for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

14 CFR 250.3 - Boarding priority rules.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Boarding priority rules. 250.3 Section 250...) ECONOMIC REGULATIONS OVERSALES § 250.3 Boarding priority rules. (a) Every carrier shall establish priority... boarding on an oversold flight in the event that an insufficient number of volunteers come forward. Such...

ACT250 Districts

Data.gov (United States)

Vermont Center for Geographic Information — The ACT 250 Districts layer is part of a larger dataset that contains administrative boundaries for Vermont's Agency of Natural Resources. The dataset includes...

30 CFR 250.1200 - Question index table.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Question index table. 250.1200 Section 250.1200 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR... Security § 250.1200 Question index table. The table in this section lists questions concerning Oil and Gas...

7 CFR 58.250 - Dry whole milk.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Dry whole milk. 58.250 Section 58.250 Agriculture... Products Bearing Usda Official Identification § 58.250 Dry whole milk. Dry whole milk in commercial bulk... Grades of Dry Whole Milk. Quality requirements for dry whole milk in consumer packages shall be for U.S...

46 CFR 28.250 - High water alarms.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false High water alarms. 28.250 Section 28.250 Shipping COAST... Individuals On Board, or for Fish Tender Vessels Engaged in the Aleutian Trade § 28.250 High water alarms. On... operating station to indicate high water level in each of the following normally unmanned spaces: (a) A...

Dicty_cDB: SSD250 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available SS (Link to library) SSD250 (Link to dictyBase) - - - Contig-U14716-1 SSD250E (Link... to Original site) - - - - - - SSD250E 491 Show SSD250 Library SS (Link to library) Clone ID SSD250 (Link to dict...yBase) Atlas ID - NBRP ID - dictyBase ID - Link to Contig Contig-U14716-1 Original site URL http://dict...t alignments: (bits) Value N U20432 |U20432.1 Dictyostelium discoideum TagB (tagB) gene, complete cds. 151 1...cName: Full=Cytochrome b-c1 complex subunit 7; AltNam... 45 0.001 DQ399515_1( DQ399515 |pid:none) Ictalurus

7 CFR 250.15 - Financial management.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Financial management. 250.15 Section 250.15 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF... Financial management. (a) Distribution charges. (1) Recipient agencies may be required to pay part or all of...

7 CFR 250.1 - General purpose and scope.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false General purpose and scope. 250.1 Section 250.1... AGRICULTURE GENERAL REGULATIONS AND POLICIES-FOOD DISTRIBUTION DONATION OF FOODS FOR USE IN THE UNITED STATES, ITS TERRITORIES AND POSSESSIONS AND AREAS UNDER ITS JURISDICTION General § 250.1 General purpose and...

Extensive interactions between HIV TAT and TAF(II)250.

Science.gov (United States)

Weissman, J D; Hwang, J R; Singer, D S

2001-03-09

The HIV transactivator, Tat, has been shown to be capable of potent repression of transcription initiation. Repression is mediated by the C-terminal segment of Tat, which binds the TFIID component, TAF(II)250, although the site(s) of interaction were not defined previously. We now report that the interaction between Tat and TAF(II)250 is extensive and involves multiple contacts between the Tat protein and TAF(II)250. The C-terminal domain of Tat, which is necessary for repression of transcription initiation, binds to a segment of TAF(II)250 that encompasses its acetyl transferase (AT) domain (885-1034 amino acids (aa)). Surprisingly, the N-terminal segment of Tat, which contains its activation domains, also binds to TAF(II)250 and interacts with two discontinuous segments of TAF(II)250 located between 885 and 984 aa and 1120 and 1279 aa. Binding of Tat to the 885-984 aa segment of TAF(II)250 requires the cysteine-rich domain of Tat, but not the acidic or glutamine-rich domains. Binding by the N-terminal domain of Tat to the 1120-1279 aa TAF(II)250 segment does not involve the acidic, cysteine- or glutamine-rich domains. Repression of transcription initiation by Tat requires functional TAF(II)250. We now demonstrate that transcription of the HIV LTR does not depend on TAF(II)250 which may account for its resistance to Tat mediated repression.

Use of radioanalytical methods for determination of uranium, neptunium, plutonium, americium and curium isotopes in radioactive wastes

International Nuclear Information System (INIS)

Geraldo, Bianca

2012-01-01

Activated charcoal is a common type of radioactive waste that contains high concentrations of fission and activation products. The management of this waste includes its characterization aiming the determination and quantification of the specific radionuclides including those known as Difficult-to-Measure Radionuclides (RDM). The analysis of the RDM's generally involves complex radiochemical analysis for purification and separation of the radionuclides, which are expensive and time-consuming. The objective of this work was to define a methodology for sequential analysis of the isotopes of uranium, neptunium, plutonium, americium and curium present in a type of radioactive waste, evaluating chemical yield, analysis of time spent, amount of secondary waste generated and cost. Three methodologies were compared and validated that employ ion exchange (TI + EC), extraction chromatography (EC) and extraction with polymers (ECP). The waste chosen was the activated charcoal from the purification system of primary circuit water cooling the reactor IEA-R1. The charcoal samples were dissolved by acid digestion followed by purification and separation of isotopes with ion exchange resins, extraction and chromatographic extraction polymers. Isotopes were analyzed on an alpha spectrometer, equipped with surface barrier detectors. The chemical yields were satisfactory for the methods TI + EC and EC. ECP method was comparable with those methods only for uranium. Statistical analysis as well the analysis of time spent, amount of secondary waste generated and cost revealed that EC method is the most effective for identifying and quantifying U, Np, Pu, Am and Cm present in charcoal. (author)

30 CFR 250.302 - Definitions concerning air quality.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Definitions concerning air quality. 250.302... Definitions concerning air quality. For purposes of §§ 250.303 and 250.304 of this part: Air pollutant means..., pursuant to section 109 of the Clean Air Act, national primary or secondary ambient air quality standards...

Solubility of Plutonium (IV) Oxalate During Americium/Curium Pretreatment

International Nuclear Information System (INIS)

Rudisill, T.S.

1999-01-01

Approximately 15,000 L of solution containing isotopes of americium and curium (Am/Cm) will undergo stabilization by vitrification at the Savannah River Site (SRS). Prior to vitrification, an in-tank pretreatment will be used to remove metal impurities from the solution using an oxalate precipitation process. Material balance calculations for this process, based on solubility data in pure nitric acid, predict approximately 80 percent of the plutonium in the solution will be lost to waste. Due to the uncertainty associated with the plutonium losses during processing, solubility experiments were performed to measure the recovery of plutonium during pretreatment and a subsequent precipitation process to prepare a slurry feed for a batch melter. A good estimate of the plutonium content of the glass is required for planning the shipment of the vitrified Am/Cm product to Oak Ridge National Laboratory (ORNL).The plutonium solubility in the oxalate precipitation supernate during pretreatment was 10 mg/mL at 35 degrees C. In two subsequent washes with a 0.25M oxalic acid/0.5M nitric acid solution, the solubility dropped to less than 5 mg/mL. During the precipitation and washing steps, lanthanide fission products in the solution were mostly insoluble. Uranium, and alkali, alkaline earth, and transition metal impurities were soluble as expected. An elemental material balance for plutonium showed that greater than 94 percent of the plutonium was recovered in the dissolved precipitate. The recovery of the lanthanide elements was generally 94 percent or higher except for the more soluble lanthanum. The recovery of soluble metal impurities from the precipitate slurry ranged from 15 to 22 percent. Theoretically, 16 percent of the soluble oxalates should have been present in the dissolved slurry based on the dilution effects and volumes of supernate and wash solutions removed. A trace level material balance showed greater than 97 percent recovery of americium-241 (from the beta dec

Total and spontaneous fission half-lives of the americium and curium nuclides

International Nuclear Information System (INIS)

Holden, N.E.

1984-01-01

The total half-life and the half-life for spontaneous fission are evaluated for the various long-lived nuclides of interest. Recommended values are presented for 241 Am, /sup 242m/Am, 243 Am, 242 Cm, 243 Cm, 244 Cm, 245 Cm, 246 Cm, 247 Cm, 248 Cm, and 250 Cm. The uncertainties are provided at the 95% confidence limit for each of the recommended values

30 CFR 250.212 - What information must accompany the EP?

Science.gov (United States)

2010-07-01

... by § 250.218; (g) Oil and hazardous substance spills information required by § 250.219; (h) Alaska... Section 250.212 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND... support facilities information required by § 250.225; (n) Coastal zone management information required by...

14 CFR 250.8 - Denied boarding compensation.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Denied boarding compensation. 250.8 Section... PROCEEDINGS) ECONOMIC REGULATIONS OVERSALES § 250.8 Denied boarding compensation. (a) Every carrier shall tender to a passenger eligible for denied boarding compensation, on the day and place the denied boarding...

21 CFR 173.250 - Methyl alcohol residues.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl alcohol residues. 173.250 Section 173.250 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD.... Methyl alcohol may be present in the following foods under the conditions specified: (a) In spice...

The recycling of the actinides neptunium, americium and curium in a fast power reactor to reduce the long term activity in a final store

International Nuclear Information System (INIS)

Beims, H.D.

1986-01-01

The starting point for the considerations and calculations given in this dissertation is the inevitable production of radioactive materials in the use of nuclear energy, which creates a considerable potential danger in a final store for a very long period. As one possibility of alleviating this problem, a concept for recycling the waste actinides neptunium, americium and curium was proposed. The waste actinides are separated in the reprocessing of burnt-up fuel elements and reach a further irradiation circuit. There they pass through the stages 'manufacture of irradiation elements', 'use in a fast power reactor' and reprocessing of irradiation elements' several times. In each irradiation and subsequent storage, about 17% of the waste actinides are removed by fission or by conversion into nuclides which can be reused as fuel, so that during the life of 40 years of the fast recycling reacor, the waste actinides can be reduced in mass by one half. In order to determine this mass reduction effect, a model calculation was developed, which includes the representation of the neutron physics and thermal properties of the reactor core and the storage and reprocessing of the irradiation elements. (orig./RB) [de

30 CFR 250.242 - What information must accompany the DPP or DOCD?

Science.gov (United States)

2010-07-01

... § 250.248; (g) Air emissions information required by § 250.249; (h) Oil and hazardous substance spills...? 250.242 Section 250.242 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR....258; (q) Sulphur operations information required by § 250.259; (r) Coastal zone management information...

12 CFR 250.260 - Miscellaneous interpretations; gold coin and bullion.

Science.gov (United States)

2010-01-01

... requirements? No. Section 19(c) of the Federal Reserve Act requires that reserve balances be satisfied either... bullion. 250.260 Section 250.260 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL RESERVE SYSTEM MISCELLANEOUS INTERPRETATIONS Interpretations § 250.260 Miscellaneous...

Gastrointestinal absorption of neptunium and curium in humans

International Nuclear Information System (INIS)

Popplewell, D.S.; Harrison, J.D.; Ham, G.J.

1991-01-01

The gastrointestinal absorption of Np and Cm has been determined in five male adult volunteers. The Np and Cm, which were in citrate solution, were taken with food. An initial experiment with each individual determined the fraction of each element excreted in the urine following intravenous administration. Subsequently, the results for urinary excretion for the two routes of administration were used to calculate the fractional absorption (f1) of ingested Np and Cm. The mean f1 values were: Np (2.0 +/- 0.2) X 10 - 4 , range (1.2-2.9) X 10 - 4 , and Cm (1.7 +/- 0.3) X 10 - 4 , range (0.95-3.0) X 10 - 4 , the quoted uncertainties being the standard error of the means. Currently, the International Commission on Radiological Protection recommends a value of 10 - 3 for both elements. Cumulative urinary excretion over 1 wk after intravenous injection accounted for about 20%-40% of administered Np and 7%-10% of Cm. At the conclusion of the experiment, the total committed effective dose equivalent for each volunteer was calculated to be in the range 130-250 microSv, based on the individual f1 values, and, in some cases, a knowledge of the rate of clearance of 239 Np through the gut as measured by whole-body counting

30 CFR 250.510 - Diesel engine air intakes.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Diesel engine air intakes. 250.510 Section 250... engine air intakes. Diesel engine air intakes must be equipped with a device to shut down the diesel engine in the event of runaway. Diesel engines that are continuously attended must be equipped with...

41 CFR 60-250.24 - Drugs and alcohol.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Drugs and alcohol. 60-250... VETERANS Discrimination Prohibited § 60-250.24 Drugs and alcohol. (a) Specific activities permitted. The contractor: (1) May prohibit the illegal use of drugs and the use of alcohol at the workplace by all...

30 CFR 250.1626 - Tubing and wellhead equipment.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Tubing and wellhead equipment. 250.1626 Section... GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1626 Tubing and wellhead equipment. (a) No tubing string shall be placed into service or continue to be used unless such...

30 CFR 250.610 - Diesel engine air intakes.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Diesel engine air intakes. 250.610 Section 250... engine air intakes. No later than May 31, 1989, diesel engine air intakes shall be equipped with a device to shut down the diesel engine in the event of runaway. Diesel engines which are continuously...

30 CFR 250.1628 - Design, installation, and operation of production systems.

Science.gov (United States)

2010-07-01

... Operations § 250.1628 Design, installation, and operation of production systems. (a) General. All production... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Design, installation, and operation of production systems. 250.1628 Section 250.1628 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF...

21 CFR 250.201 - Preparations for the treatment of pernicious anemia.

Science.gov (United States)

2010-04-01

... anemia. 250.201 Section 250.201 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... Drugs and Foods § 250.201 Preparations for the treatment of pernicious anemia. (a) The ninth announcement of the Anti-anemia Preparations Advisory Board of the United States Pharmacopeia is concerned with...

14 CFR 250.2a - Policy regarding denied boarding.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Policy regarding denied boarding. 250.2a... PROCEEDINGS) ECONOMIC REGULATIONS OVERSALES § 250.2a Policy regarding denied boarding. In the event of an... confirmed reserved space on that flight are denied boarding involuntarily. ...

Separation and recovery of Cm from Cm-Pu mixed oxide samples containing Am impurity

International Nuclear Information System (INIS)

Hirokazu Hayashi; Hiromichi Hagiya; Mitsuo Akabori; Yasuji Morita; Kazuo Minato

2013-01-01

Curium was separated and recovered as an oxalate from a Cm-Pu mixed oxide which had been a 244 Cm oxide sample prepared more than 40 years ago and the ratio of 244 Cm to 240 Pu was estimated to 0.2:0.8. Radiochemical analyses of the solution prepared by dissolving the Cm-Pu mixed oxide in nitric acid revealed that the oxide contained about 1 at% of 243 Am impurity. To obtain high purity curium solution, plutonium and americium were removed from the solution by an anion exchange method and by chromatographic separation using tertiary pyridine resin embedded in silica beads with nitric acid/methanol mixed solution, respectively. Curium oxalate, a precursor compound of curium oxide, was prepared from the purified curium solution. 11.9 mg of Cm oxalate having some amounts of impurities, which are 243 Am (5.4 at%) and 240 Pu (0.3 at%) was obtained without Am removal procedure. Meanwhile, 12.0 mg of Cm oxalate (99.8 at% over actinides) was obtained with the procedure including Am removals. Both of the obtained Cm oxalate sample were supplied for the syntheses and measurements of the thermochemical properties of curium compounds. (author)

21 CFR 1271.250 - Labeling controls.

Science.gov (United States)

2010-04-01

..., AND CELLULAR AND TISSUE-BASED PRODUCTS Current Good Tissue Practice § 1271.250 Labeling controls. (a... available for distribution is accompanied by documentation of the donor eligibility determination as...

30 CFR 250.463 - Who establishes field drilling rules?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Who establishes field drilling rules? 250.463... GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Other Drilling Requirements § 250.463 Who establishes field drilling rules? (a) The District Manager may...

40 CFR 265.250 - Applicability.

Science.gov (United States)

2010-07-01

... Piles § 265.250 Applicability. The regulations in this subpart apply to owners and operators of facilities that treat or store hazardous waste in piles, except as § 265.1 provides otherwise. Alternatively, a pile of hazardous waste may be managed as a landfill under subpart N. ...

7 CFR 250.17 - Reports.

Science.gov (United States)

2010-01-01

...) Inventory reports and receipt of donated foods. Distributing agencies shall complete and submit to the FNSRO semiannual reports regarding excessive inventories (as defined in § 250.14(f)) of donated foods, utilizing form FNS-155, the Inventory Management Register, except that distributing agencies shall submit monthly...

40 CFR 264.250 - Applicability.

Science.gov (United States)

2010-07-01

... OWNERS AND OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Waste Piles § 264.250... treat hazardous waste in piles, except as § 264.1 provides otherwise. (b) The regulations in this subpart do not apply to owners or operators of waste piles that are closed with wastes left in place. Such...

30 CFR 250.518 - What are the requirements for casing pressure management?

Science.gov (United States)

2010-07-01

... Operations Casing Pressure Management § 250.518 What are the requirements for casing pressure management... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are the requirements for casing pressure management? 250.518 Section 250.518 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR...

30 CFR 250.131 - Will MMS notify me before conducting an inspection?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Will MMS notify me before conducting an inspection? 250.131 Section 250.131 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR... § 250.131 Will MMS notify me before conducting an inspection? MMS conducts both scheduled and...

30 CFR 250.231 - After receiving the EP, what will MMS do?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false After receiving the EP, what will MMS do? 250.231 Section 250.231 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE... Decision Process for the Ep § 250.231 After receiving the EP, what will MMS do? (a) Determine whether...

30 CFR 250.123 - Will MMS allow gas storage on unleased lands?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Will MMS allow gas storage on unleased lands? 250.123 Section 250.123 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR... § 250.123 Will MMS allow gas storage on unleased lands? You may not store gas on unleased lands unless...

30 CFR 250.207 - What ancillary activities may I conduct?

Science.gov (United States)

2010-07-01

... surveys; or (c) Studies that model potential oil and hazardous substance spills, drilling muds and... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What ancillary activities may I conduct? 250.207 Section 250.207 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE...

Johann Wilhelm Krause 250 / Triin Ojari

Index Scriptorium Estoniae

Ojari, Triin, 1974-

2007-01-01

Eesti klassitsistliku arhitektuuri suurkuju ning Tartu Ülikooli arhitekti Johann Wilhelm Krause 250. sünniaastapäeva tähistati näitustega Tallinnas ja Tartus. Tartu Ülikooli raamatukogu kunstikogusse kuulub ligi 700 J. W. Krause loodud joonistust

Estimation of 244Cm intake by bioassay measurements following a contamination incident

International Nuclear Information System (INIS)

Thein, M.; Bogard, J.S.; Eckerman, K.F.

1990-01-01

An employee was contaminated with radioactive material consisting primarily of 244 Cm and 246 Cm as a consequence of handling a curium nitrate solution at a reprocessing facility. In vivo gamma analysis and in vitro (urine and fecal) bioassay measurements were performed. A sample of the curium solution from the workplace was obtained to confirm that the nitrate was the chemical form and to identify the isotopes of curium present. The mass ratio of 244 Cm/ 246 Cm was determined to be 91 to 7. Observed excretion rates were consistent with available information on curium. The results of the in vivo and in vitro measurements are presented and intake estimates for the incident are developed. (author) 11 refs.; 3 figs.; 2 tabs

30 CFR 250.1504 - May I use alternative training methods?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false May I use alternative training methods? 250... Safety Training § 250.1504 May I use alternative training methods? You may use alternative training methods. These methods may include computer-based learning, films, or their equivalents. This training...

7 CFR 250.13 - Distribution and control of donated foods.

Science.gov (United States)

2010-01-01

...) Minimum donations. Foods shall be donated only in such quantities as will protect the lower truck load... 7 Agriculture 4 2010-01-01 2010-01-01 false Distribution and control of donated foods. 250.13 Section 250.13 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION...

Separation and activity determination of 239+240Pu, 241Am and Curium (242and244Cm) in evaporator concentrate by Alpha Spectrometry

International Nuclear Information System (INIS)

Reis Junior, Aluisio S.; Temba, Eliane S.C.; Kastner, Geraldo F.; Monteiro, Roberto P.G.

2013-01-01

Alpha spectrometry analysis was used for activity determinations of Pu, Am and Cm isotopes in evaporator concentrate samples from nuclear power plants. Using a sequential procedure the first step was Pu isolation by an anion exchange column followed by an Am and Cm separation of U and Fe by a co-precipitation with oxalic acid. The precipitate was used for americium and curium separation of strontium by using a TRU resin extraction chromatography column. Due to their chemical similarities and energy difference it was seen that the simultaneous determination of 241 Am, 242 Cm and 24 3 ,244 Cm isotopes is possible using the 243 Am as tracer, once they have peaks in different region of interest (ROI) in the alpha spectrum. In this work it was used tracers, 238 Pu, 243 Am, 244 Cm and 232 U, for determination and quantification of theirs isotopes, respectively. The standard deviations for replicate analysis were calculated and for 241 Am it was (1,040 ± 160 mBqKg -1 ), relative standard deviation 15.38%, and for 239+240 Pu it was (551 +- 44 mBqKg -1 ), relative standard deviation 7.98%. In addition, for the 242 Cm isotope the standard deviation for determinations was(75 ± 23 mBqKg -1 ), with the relative standard deviation 30.67% higher than for 241 Am and 239+240 Pu. The radiometric yields ranged from 90% to 105% and the lower limit of detection was estimated as being 2.05 mBqKg -1 . (author)

Hybrid Propulsion Demonstration Program 250K Hybrid Motor

Science.gov (United States)

Story, George; Zoladz, Tom; Arves, Joe; Kearney, Darren; Abel, Terry; Park, O.

2003-01-01

The Hybrid Propulsion Demonstration Program (HPDP) program was formed to mature hybrid propulsion technology to a readiness level sufficient to enable commercialization for various space launch applications. The goal of the HPDP was to develop and test a 250,000 pound vacuum thrust hybrid booster in order to demonstrate hybrid propulsion technology and enable manufacturing of large hybrid boosters for current and future space launch vehicles. The HPDP has successfully conducted four tests of the 250,000 pound thrust hybrid rocket motor at NASA's Stennis Space Center. This paper documents the test series.

5 CFR 250.203 - Agency responsibilities.

Science.gov (United States)

2010-01-01

... management on its overall mission performance. (2) Human capital accountability system. This system provides... MANAGEMENT IN AGENCIES Strategic Human Capital Management § 250.203 Agency responsibilities. (a) To assist in... and initiatives as appropriate, consistent with agency strategic plans and annual performance goals...

Safe handling of kilogram amounts of fuel-grade plutonium and of gram amounts of plutonium-238, americium-241 and curium-244

International Nuclear Information System (INIS)

Louwrier, K.P.; Richter, K.

1976-01-01

During the past 10 years about 600 glove-boxes have been installed at the Institute for Transuranium Elements at Karlsruhe. About 80% of these glove-boxes have been designed and equipped for handling 100-g to 1-kg amounts of 239 Pu containing 8-12% 240 Pu (low-exposure plutonium). A small proportion of the glove-boxes is equipped with additional shielding in the form of lead sheet or lead glass for work with recycled plutonium. In these glove-boxes gram-amounts of 241 Am have also been handled for preparation of Al-Am targets using tongs and additional shielding inside the glove-boxes themselves. Water- and lead-shielded glove-boxes equipped with telemanipulators have been installed for routine work with gram-amounts of 241 Am, 243 Am and 244 Cm. A prediction of the expected radiation dose for the personnel is difficult and only valid for a preparation procedure with well-defined preparation steps, owing to the fact that gamma dose-rates depend strongly upon proximity and source seize. Gamma radiation dose measurements during non-routine work for 241 Am target preparation showed that handling of gram amounts leads to a rather high irradiation dose for the personnel, despite lead or steel glove-box shielding and shielding within the glove-boxes. A direct glove-hand to americium contact must be avoided. For all glove-handling of materials with gamma radiation an irradiation control of the forearms of the personnel by, for example, thermoluminescence dosimeters is necessary. Routine handling of americium and curium should be executed with master-slave equipment behind neutron and gamma shielding. (author)

30 CFR 250.1152 - How do I conduct well tests?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How do I conduct well tests? 250.1152 Section... Tests and Surveys § 250.1152 How do I conduct well tests? (a) When you conduct well tests you must: (1... during completion, recompletion, reworking, or treatment operations before you start a well test; (2...

21 CFR 172.250 - Petroleum naphtha.

Science.gov (United States)

2010-04-01

... naphtha is used or intended for use as a solvent in protective coatings on fresh citrus fruit in... CONSUMPTION (CONTINUED) FOOD ADDITIVES PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION Coatings...-oxidation, the entire procedure is to be carried out under subdued light. apparatus Separatory funnels. 250...

30 CFR 250.1634 - Site security.

Science.gov (United States)

2010-07-01

... Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1634 Site security. (a) All locations... Regional Supervisor as soon as possible but no later than the next business day after discovery of the...

30 CFR 250.1406 - When will MMS notify me and provide penalty information?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When will MMS notify me and provide penalty information? 250.1406 Section 250.1406 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE... (OCS) Civil Penalties § 250.1406 When will MMS notify me and provide penalty information? If the...

14 CFR 250.6 - Exceptions to eligibility for denied boarding compensation.

Science.gov (United States)

2010-01-01

... boarding compensation. 250.6 Section 250.6 Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF... boarding compensation. A passenger denied boarding involuntarily from an oversold flight shall not be eligible for denied boarding compensation if: (a) The passenger does not comply fully with the carrier's...

Electric resistivity of 241-americium and 244-curium metals. Creation of defects and isochronous annealing of 241-americium metal after self-irradiation

International Nuclear Information System (INIS)

Schenkel, R.

1977-03-01

The temperature dependence of the electrical resistivity of thin films of bulk 241 Am metal were measured between 300 and 4.5 K. The room temperature resistivity was found to be 68.90μΩcm. At room temperature the electrical resistivity of americium increases with pressure (3% up to 13 kbar). The application of 13 kbar pressure did not change the low temperature power law in the electrical resistivity. The resistivity vs temperature curve can be explained by assuming s-d scattering of conduction electrons. The localized 5f electrons are considered to be about 5eV below the Fermi level. Americium therefore should be the first lanthanide-like element in the actinide series. The defect production due to self-irradiation damage was studied by measuring the increase of the resistivity at 4.2 K over a period of 738 h. A saturation resistivity of 16.036 μΩcm was found corresponding to a defect concentration of about 0.22 a/o. After isochronal annealing two recovery stages were observed at about 65 and 145 K. The two stages shift with increasing initial defect concentration to lower temperatures. Estimates of the activation energies and the reaction order were made and possible defect reactions suggested. The magnetic contribution to the electrical resistivity of curium, which shows an antiferromagnetic transition at 52.5 k, was obtained by subtracting the resistivity of americium (to be considered as phonon part). Comparison with theoretical models were made. At low temperatures the measurements are strongly affected by self-irradiation damage [drho/dt(t=0)=9.8μΩcm/h

7 CFR 250.52 - Storage and inventory management of donated foods.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Storage and inventory management of donated foods. 250... Donated Foods in Contracts With Food Service Management Companies § 250.52 Storage and inventory management of donated foods. (a) General requirements. The food service management company must meet the...

48 CFR 52.250-1 - Indemnification Under Public Law 85-804.

Science.gov (United States)

2010-10-01

... caused by willful misconduct or lack of good faith on the part of any of the Contractor's principal... Public Law 85-804. 52.250-1 Section 52.250-1 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION (CONTINUED) CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and...

40 CFR 421.250 - Applicability: Description of the primary precious metals and mercury subcategory.

Science.gov (United States)

2010-07-01

... primary precious metals and mercury subcategory. 421.250 Section 421.250 Protection of Environment... POINT SOURCE CATEGORY Primary Precious Metals and Mercury Subcategory § 421.250 Applicability: Description of the primary precious metals and mercury subcategory. The provisions of this subpart are...

17 CFR 250.4 - Exemption of certain brokers, dealers and underwriters.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Exemption of certain brokers... and General Exemptions § 250.4 Exemption of certain brokers, dealers and underwriters. (a) General exemption. Subject to the provision of § 250.6, any broker, dealer or underwriter, as defined in paragraph...

Pulverização em CDA 250 herbicida pendimethalin na cultura do arroz de sequeiro Application of pendimethalin with cda 250 spfayer for upland rice

Directory of Open Access Journals (Sweden)

T. Matuo

1984-01-01

Full Text Available Foi estudada a viabilidade de utilização da pulverização CDA 25C, na aplicação do herbicida em pré-emergência na cultura do arroz de sequeiro. O herbicida empregado foi o pendimethalin nas doses de 0,0; 1,5; 2,0; 2,5 e 3,0 litro s/ha da formulação comercial a 50%. A pulverização convencional foi efetuada com bicos 11003 com consumo de 200 litros de calda per hectare. O processo CDA 250 foi aplicado por meio de bico rotativo (Micromax com dois níveis de consumo de calda : 50 1/ha e 27 1/ha. Os resultados mostraram que: a - o método CDA 250 proporciona controle dc mato e produtividade de arroz equivalentes ao método convencional; b para o bico Micromax, a aplicação da formulação comercial de pendimethalin a 50% com vazão de 0,48 1/min./bico, a distância entre bicos deve ser de 1,75 m e para a vazão de 0,96 1/min./bloco, essa distancia deve ser de 1,90 m; c- a aplicação do pendimethalin 50% C.E. pelo processo CDA 250, empregando 27 litros de calda por hectare foi o processo mais interessante por oferecer vantagens logísticas apreciáveis.The feasibility of pre-emergenge herbicide application for upland rice by CDA 250 spray method was studied. The herbicide used was pen dimethalin at 0,0; 1,5; 2,0; 2,5 and 3,0 1/ha of comercial 50% E.C. formulation. Conventional spraying was carried out using 110C3 flat fan nozzles applying 200 1/ha of spray volume CDA250 was applied by rotary atomizers (Micromax spraying twc volume rates: 50 1/ha and 27 1/ha. The results pointed out that: a- CDA 250 spray method was equivalent to the conventional spray method in the control of weeds and crop yield; b - for Micromax nozzles applying commercial 50 E.C. formulation of pendimethalin at 0,48 /min of nozzle feed rate, the distance between nozzles should be 1,75 m and at 0,96 1/min feed rate this distance shoud be 1,90 m; c- CDA 250, applying 27 1/ha presents large logistic advantages.

33 CFR 96.250 - What documents and reports must a safety management system have?

Science.gov (United States)

2010-07-01

... safety management system have? 96.250 Section 96.250 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY VESSEL OPERATING REGULATIONS RULES FOR THE SAFE OPERATION OF VESSELS AND SAFETY MANAGEMENT SYSTEMS Company and Vessel Safety Management Systems § 96.250 What documents and...

13 CFR 107.250 - Exclusion of stock options issued by Licensee from Management Expenses.

Science.gov (United States)

2010-01-01

... Sbic § 107.250 Exclusion of stock options issued by Licensee from Management Expenses. Stock options... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Exclusion of stock options issued by Licensee from Management Expenses. 107.250 Section 107.250 Business Credit and Assistance SMALL...

17 CFR 250.28 - Inconsistent financial statements.

Science.gov (United States)

2010-04-01

... Accounts § 250.28 Inconsistent financial statements. Except as otherwise authorized or required by the..., financial statements which are inconsistent with the book accounts of such company or financial statements... prevent the distribution or publication of reasonable condensations or of unaudited financial statements...

5 CFR 250.201 - Coverage and purpose.

Science.gov (United States)

2010-01-01

....201 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PERSONNEL MANAGEMENT IN AGENCIES Strategic Human Capital Management § 250.201 Coverage and purpose. The Chief Human... effective and efficient operation of Government. As a part of OPM's overall leadership responsibilities in...

Uranium and transuranium analysis

International Nuclear Information System (INIS)

Regnaud, F.

1989-01-01

Analytical chemistry of uranium, neptunium, plutonium, americium and curium is reviewed. Uranium and neptunium are mainly treated and curium is only briefly evoked. Analysis methods include coulometry, titration, mass spectrometry, absorption spectrometry, spectrofluorometry, X-ray spectrometry, nuclear methods and radiation spectrometry [fr

30 CFR 250.109 - What documents must I prepare and maintain related to welding?

Science.gov (United States)

2010-07-01

... related to welding? 250.109 Section 250.109 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF... Performance Standards § 250.109 What documents must I prepare and maintain related to welding? (a) You must submit a Welding Plan to the District Manager before you begin drilling or production activities on a...

30 CFR 250.1711 - When will MMS order me to permanently plug a well?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When will MMS order me to permanently plug a well? 250.1711 Section 250.1711 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE... Activities Permanently Plugging Wells § 250.1711 When will MMS order me to permanently plug a well? MMS will...

30 CFR 250.204 - How must I protect the rights of the Federal government?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How must I protect the rights of the Federal government? 250.204 Section 250.204 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR... Information § 250.204 How must I protect the rights of the Federal government? (a) To protect the rights of...

30 CFR 250.266 - After receiving the DPP or DOCD, what will MMS do?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false After receiving the DPP or DOCD, what will MMS do? 250.266 Section 250.266 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR... Decision Process for the Dpp Or Docd § 250.266 After receiving the DPP or DOCD, what will MMS do? (a...

The Varian MAT-250 mass spectrometer. Steady isotopes laboratory; Espectrometro de masas Varian MAT-250. Laboratorio de isotopos estables

Energy Technology Data Exchange (ETDEWEB)

Hernandez M, V.; Tavera D, M.L. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

1997-07-01

This work treats over the performance and applications of the Varian Mat-250 mass spectrometer which is in the environmental isotope laboratory. It can be applied over topics such as: ions formation, acceleration and collimation, ions separation, ions detection, data transformation, sampling, {delta} notation. (Author)

30 CFR 250.1202 - Liquid hydrocarbon measurement.

Science.gov (United States)

2010-07-01

... FMPs; Inclusion of production from additional structures; Meter updates which add buy-back gas meters... the API MPMS as incorporated by reference in 30 CFR 250.198, when obtaining net standard volume and... manufacturer; (ii) Meters operate within the manufacturer's specifications for maximum and minimum flow rate...

Galvanic interactions of HE15 /MDN138 & HE15 /MDN250 alloys in natural seawater

Science.gov (United States)

Parthiban, G. T.; Subramanian, G.; Muthuraman, K.; Ramakrishna Rao, P.

2017-06-01

HE15 is a heat treatable high strength alloy with excellent machinability find wide applications in aerospace and defence industries. In view of their excellent mechanical properties, workability, machinability, heat treatment characteristics and good resistance to general and stress corrosion cracking, MDN138 & MDN250 have been widely used in petrochemical, nuclear and aerospace industries. The galvanic corrosion behaviour of the metal combinations HE15 /MDN138 and HE15 /MDN250, with 1:1 area ratio, has been studied in natural seawater using the open well facility of CECRI's Offshore Platform at Tuticorin for a year. The open circuit potentials of MDN138, MDN250 and HE15 of the individual metal, the galvanic potential and galvanic current of the couples HE15 /MDN138 and HE15 /MDN250 were periodically monitored throughout the study period. The calcareous deposits on MDN138 and MDN250 in galvanic contact with HE15 were analyzed using XRD. The electrochemical behaviors of MDN138, MDN250 and HE15 in seawater have been studied using an electrochemical work station. The surface characteristics of MDN138 and MDN250 in galvanic contact with HE15 have been examined with scanning electron microscope. The results of the study reveal that HE15 offered required amount of protection to MDN138 & MDN250.

30 CFR 250.221 - What environmental monitoring information must accompany the EP?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What environmental monitoring information must accompany the EP? 250.221 Section 250.221 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE... necessary under the MMPA. (c) Flower Garden Banks National Marine Sanctuary (FGBNMS). If you propose to...

New model for the lunar interior to 250 km

International Nuclear Information System (INIS)

Piwinskii, A.J.; Duba, A.G.

1975-01-01

A new model for the structure of the lunar interior to about a 250-km depth is proposed. It is suggested that this region is composed of plagioclase-bearing rocks, and that the 65-km seismic discontinuity represents the appearance of garnet. A variety of rock types mainly composed of plagioclase, pyroxene, olivine and garnet is envisioned, with at least half of the outer 250 km of the moon made of plagioclase, which dominates the electrical conductivity. This model agrees with recent petrological and electrical conductivity results and does not violate velocity-depth profiles obtained from elastic-wave studies of lunar and terrestrial materials. (U.S.)

30 CFR 250.1003 - Installation, testing, and repair requirements for DOI pipelines.

Science.gov (United States)

2010-07-01

.... (a)(1) Pipelines greater than 8-5/8 inches in diameter and installed in water depths of less than 200... for DOI pipelines. 250.1003 Section 250.1003 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Pipelines...

Targeted therapy of renal cell carcinoma: synergistic activity of cG250-TNF and IFNg.

NARCIS (Netherlands)

Bauer, S.; Oosterwijk-Wakka, J.C.; Adrian, N.; Oosterwijk, E.; Fischer, E.; Wuest, T.; Stenner, F.; Perani, A.; Cohen, L.; Knuth, A.; Divgi, C.; Jager, D.; Scott, A.M.; Ritter, G.; Old, L.J.; Renner, C.

2009-01-01

Immunotherapeutic targeting of G250/Carbonic anhydrase IX (CA-IX) represents a promising strategy for treatment of renal cell carcinoma (RCC). The well characterized human-mouse chimeric G250 (cG250) antibody has been shown in human studies to specifically enrich in CA-IX positive tumors and was

30 CFR 250.195 - What notification does MMS require on the production status of wells?

Science.gov (United States)

2010-07-01

... the well in a production status. You must confirm oral notification by telefax or e-mail within those... production status of wells? 250.195 Section 250.195 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... Information and Reporting Requirements § 250.195 What notification does MMS require on the production status...

30 CFR 250.226 - What Coastal Zone Management Act (CZMA) information must accompany the EP?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What Coastal Zone Management Act (CZMA) information must accompany the EP? 250.226 Section 250.226 Mineral Resources MINERALS MANAGEMENT SERVICE... and Information Contents of Exploration Plans (ep) § 250.226 What Coastal Zone Management Act (CZMA...

14 CFR 250.2b - Carriers to request volunteers for denied boarding.

Science.gov (United States)

2010-01-01

... boarding. 250.2b Section 250.2b Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION... boarding. (a) In the event of an oversold flight, every carrier shall request volunteers for denied boarding before using any other boarding priority. A “volunteer” is a person who responds to the carrier's...

Type B accident investigation board report of the July 2, 1997 curium intake by shredder operator at Building 513 Lawrence Livermore National Laboratory, Livermore, California. Final report

International Nuclear Information System (INIS)

1997-08-01

On July 2, 1997 at approximately 6:00 A.M., two operators (Workers 1 and 2), wearing approved personal protective equipment (PPE), began a shredding operation of HEPA filters for volume reduction in Building 513 (B-513) at Lawrence Livermore National Laboratory (LLNL). The waste requisitions indicated they were shredding filters containing ≤ 1 μCi of americium-241 (Am-241). A third operator (Worker 3) provided support to the shredder operators in the shredding area (hot area) from a room that was adjacent to the shredding area (cold area). At Approximately 8:00 A.M., a fourth operator (Worker 4) relieved Worker 2 in the shredding operation. Sometime between 8:30 A.M. and 9:00 A.M., Worker 3 left the cold area to make a phone call and set off a hand and foot counter in Building 514. Upon discovering the contamination, the shredding operation was stopped and surveys were conducted in the shredder area. Surveys conducted on the workers found significant levels of contamination on their PPE and the exterior of their respirator cartridges. An exit survey of Worker 1 was conducted at approximately 10:05 A.M., and found contamination on his PPE, as well as on the exterior and interior of his respirator. Contamination was also found on his face, chest, back of neck, hair, knees, and mustache. A nose blow indicated significant contamination, which was later determined to be curium-244

Transactivation mediated by B-Myb is dependent on TAF(II)250.

Science.gov (United States)

Bartusel, Thorsten; Klempnauer, Karl-Heinz

2003-05-15

B-Myb is a highly conserved member of the Myb family of transcription factors, which has been implicated in cell cycle regulation. B-Myb is expressed in most proliferating cells and its activity is highly regulated around the G1/S-phase border of the cell cycle. It is generally assumed that B-Myb regulates the expression of genes that are crucial for cell proliferation; however, the identity of these genes, the molecular mechanisms by which B-Myb stimulates their expression and the involvement of other proteins have not been sufficiently clarified. We have employed the hamster cell line ts13 as a tool to demonstrate a functional link between B-Myb and the coactivator TAF(II)250, a key component of the transcriptional machinery which itself is essential for cell proliferation. ts13 cells express a point-mutated version of TAF(II)250 whose intrinsic histone acetyl transferase activity is temperature sensitive. Transactivation of Myb-responsive reporter genes by B-Myb is temperature-dependent in ts13 cells but not in ts13 cells, which have been rescued by transfection with an expression vector for wild-type TAF(II)250. Furthermore, B-Myb and TAF(II)250 can be coprecipitated, suggesting that both proteins are present in a complex. The formation of this complex is dependent on the DNA-binding domain of B-Myb and not on its transactivation domain. Taken together, these observations provide the first evidence that the coactivator TAF(II)250 is involved in the activation of Myb responsive promoters by B-Myb. The finding that B-Myb transactivation is dependent on a key coactivator involved in cell cycle control is consistent with and strengthens the idea that B-Myb plays a crucial role as a transcription factor in proliferating cells.

Valurautaisten 160 - 250 kokoluokan jarrumoottorien suunnitteluohje

OpenAIRE

Järvi, Markus

2016-01-01

ABB Oy:n Motors and Generators – yksikön sovellussuunnitteluosasto tarvitsi suunnitteluohjetta valurautaisille 160 – 250 kokoluokan jarrumoottoreille. Jarrumoottoreiden suunnittelu ja tuotanto ohjattiin vuoden 2015 keväällä Vaasan moottoritehtaalle ja Ruotsista tulleet ohjeet sekä dokumentointi kaipasivat parannusta. Ohjeen tarkoituksena on olla suunnittelun ja myynnin tukena. Ohje on tehty englannin kielellä, jotta sitä pystytään käyttämään ABB:n organisaatiossa myös Suomen ulkopuolella. ...

Determination of Neptunium, Americium and Curium in Spent Nuclear Fuel Samples by Alpha Spectrometry Using 239Np and 243Am as a Spike and a Tracer

International Nuclear Information System (INIS)

Jeo, Kih-Soo; Song, Byung-Chul; Kim, Young-Bok; Han, Sun-Ho; Jeon, Young-Shin; Jung, Euo-Chang; Jee, Kwang-Yong

2007-01-01

Determination of actinide elements and fission products in spent nuclear fuels is of importance for a burnup determination and source term evaluation. Especially, the amounts of uranium and plutonium isotopes are used for the evaluation of a burnup credit in spent nuclear fuels. Additionally, other actinides such as Np, Am and Cm in spent nuclear fuel samples is also required for the purposes mentioned above. In this study, 237 Np, 241 Am and 244 Cm were determined by an alpha spectrometry for the source term data for high burnup spent nuclear fuels ranging from 37 to 62.9 GWD/MtU as a burnup. Generally, mass spectrometry has been known as the most powerful method for isotope determinations such as high concentrations of uranium and plutonium. However, in the case of minor actinides such as Np, Am and Cm, alpha spectrometry would be recommended instead. Determination of the transuranic elements in spent nuclear fuel samples is different from that for environmental samples because the amount of each nuclide in the spent fuel samples is higher and the relative ratios between each nuclide are also different from those for environmental samples. So, it is important to select an appropriate tracer and an optimum sample size depending on the nuclides and analytical method. In this study 237 Np was determined by an isotope dilution alpha(gamma) spectrometry using 239 Np as a spike, and 241 Am and curium isotopes were determined by alpha spectrometry using 243 Am as a tracer. The content of each nuclide was compared with that by the Origen-2 code

30 CFR 250.286 - What is a DWOP?

Science.gov (United States)

2010-07-01

... development project, and any other project that uses non-conventional production or completion technology... Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Deepwater Operations Plans (dwop) § 250.286...

Recovery of trans-plutonium elements; Recuperation des elements transplutoniens

Energy Technology Data Exchange (ETDEWEB)

Espie, J Y; Poncet, B; Simon, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1970-07-01

The object of this work is to study the recovery of americium and curium from the fission-product solution obtained from the processing of irradiated fuel elements made of natural metallic uranium alloyed with aluminium, iron and silicon; these elements have been subjected to an average irradiation of 4000 MW days/ton in a gas-graphite type reactor having a thermal power of 3.7 MW/ton of uranium. The process used consists of 3 extraction cycles and one americium-curium separation: - 1) extraction cycle in 40 per cent TBP: extraction of actinides and lanthanides; elimination of fission products; - 2) extraction cycle in 8 per cent D2EHPA: decontamination from the fission products, decontamination of actinides from lanthanides; - 3) extraction cycle in 40 per cent TBP: separation of the complexing agent and concentration of the actinides; - 4) americium-curium separation by precipitation. (authors) [French] Cette etude a pour objet, la recuperation de l'americium et du curium de la solution de produits de fission provenant du traitement de combustibles irradies a base d'uranium naturel metallique allie a l'aluminium, le fer, et le silicium, et ayant subi une irradiation moyenne de 4000 MWj/t dans une pile du type graphite-gaz, dont la puissance thermique est de 3.7 MW/t d'uranium. Le procede utilise comprend 3 cycles d'extraction et une separation americium-curium: - 1. cycle d'extraction dans le TBP a 40 pour cent: extraction des actinides et des lanthanides, elimination des produits de fission; - 2. cycle d'extraction dans le D2EHPA a 8 pour cent: decontamination en produits de fission, decontamination des actinides en lanthanides; - 3. cycle d'extraction dans le TBP a 40 pour cent: separation du complexant et concentration des actinides; - 4. separation americium-curium par precipitation. (auteurs)

30 CFR 250.107 - What must I do to protect health, safety, property, and the environment?

Science.gov (United States)

2010-07-01

..., property, and the environment? 250.107 Section 250.107 Mineral Resources MINERALS MANAGEMENT SERVICE... Performance Standards § 250.107 What must I do to protect health, safety, property, and the environment? (a) You must protect health, safety, property, and the environment by: (1) Performing all operations in a...

34 CFR 75.250 - Project period can be up to 60 months.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Project period can be up to 60 months. 75.250 Section... Are Made Approval of Multi-Year Projects § 75.250 Project period can be up to 60 months. The Secretary may approve a project period of up to 60 months. (Authority: 20 U.S.C. 1221e-3 and 3474) [45 FR 22497...

Determination of 241Am and 244Cm in environmental samples

International Nuclear Information System (INIS)

Bonino, N.O.; Grinman, A.D.R.; Serdeiro, N.H.

1998-01-01

The present technique describes a method to separate, purify and measure low levels of americium and curium in different environmental samples such as sediments, soils, water, vegetables, and air filters. The determination of radionuclides in theses environmental matrices have analytical problems, since a simple method doesn't exist for the purification, which is indispensable for its later measuring alpha spectrometry. The developed technique consist on taking an aliquot of the sample to analyze, to add tracer as americium 243 and curium 242, and to dissolve the matrix in a such way to have a clear solution. For the isolation of the americium and curium of the other actinides ar used as separation techniques: precipitation with Fe 3+ , anionic and cationic exchange, and extraction with a appropriate organic solvent. The purification of the americium and curium is followed by the electrodeposition habitually used. The measurement is carried out by alpha spectrometry with a detector of implanted ion. The detection limit for this techniques is of 0,002 Bq/l or 0,2 mBq in the case of filters. (author)

Functional substitution for TAF(II)250 by a retroposed homolog that is expressed in human spermatogenesis.

Science.gov (United States)

Wang, P Jeremy; Page, David C

2002-09-15

TAF(II)250, the largest subunit of the general transcription factor TFIID, is expressed from the human X chromosome, at least in somatic cells. In male meiosis, however, the sex chromosomes are transcriptionally silenced, while the autosomes remain active. How then are protein-encoding genes transcribed during human male meiosis? Here we present a novel autosomal human gene, TAF1L, which is homologous to TAF(II)250 and is expressed specifically in the testis, apparently in germ cells. We hypothesize that during male meiosis, transcription of protein-encoding genes relies upon TAF1L as a functional substitute for TAF(II)250. Like TAF(II)250, the human TAF1L protein can bind directly to TATA-binding protein, an essential component of TFIID. Most importantly, transfection with human TAF1L rescued the temperature-sensitive lethality of a hamster cell line mutant in TAF(II)250. TAF1L lacks introns and evidently arose by retroposition of a processed TAF(II)250 mRNA during primate evolution. The observation that TAF1L can functionally replace TAF(II)250 provides experimental support for the hypothesis that during male meiosis, autosomes provide cellular functions usually supplied by the X chromosome in somatic cells.

30 CFR 250.921 - How do I analyze my platform for cumulative fatigue?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How do I analyze my platform for cumulative fatigue? 250.921 Section 250.921 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR... fatigue? (a) If you are required to analyze cumulative fatigue on your platform because of the results of...

47 CFR 10.250 - Notification to existing subscribers of non-participation in CMAS.

Science.gov (United States)

2010-10-01

... provider shall use any reasonable method at its disposal to alert the customer to a change in the terms and...-participation in CMAS. 10.250 Section 10.250 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL... Rule 47 CFR 10.240. (c) In the case of prepaid customers, if a mailing address is available, the CMS...

7 CFR 250.60 - Use of donated foods in the school food service.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Use of donated foods in the school food service. 250.60 Section 250.60 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE GENERAL REGULATIONS AND POLICIES-FOOD DISTRIBUTION DONATION OF FOODS FOR USE IN THE UNITED STATES, ITS...

30 CFR 250.617 - Tubing and wellhead equipment.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Tubing and wellhead equipment. 250.617 Section... Tubing and wellhead equipment. The lessee shall comply with the following requirements during well-workover operations with the tree removed: (a) No tubing string shall be placed in service or continue to...

30 CFR 250.401 - What must I do to keep wells under control?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must I do to keep wells under control? 250... General Requirements § 250.401 What must I do to keep wells under control? You must take necessary precautions to keep wells under control at all times. You must: (a) Use the best available and safest drilling...

Memory timeline: Brain ERP C250 (not P300) is an early biomarker of short-term storage.

Science.gov (United States)

Chapman, Robert M; Gardner, Margaret N; Mapstone, Mark; Dupree, Haley M; Antonsdottir, Inga M

2015-04-16

Brain event-related potentials (ERPs) offer a quantitative link between neurophysiological activity and cognitive performance. ERPs were measured while young adults performed a task that required storing a relevant stimulus in short-term memory. Using principal components analysis, ERP component C250 (maximum at 250 ms post-stimulus) was extracted from a set of ERPs that were separately averaged for various task conditions, including stimulus relevancy and stimulus sequence within a trial. C250 was more positive in response to task-specific stimuli that were successfully stored in short-term memory. This relationship between C250 and short-term memory storage of a stimulus was confirmed by a memory probe recall test where the behavioral recall of a stimulus was highly correlated with its C250 amplitude. ERP component P300 (and its subcomponents of P3a and P3b, which are commonly thought to represent memory operations) did not show a pattern of activation reflective of storing task-relevant stimuli. C250 precedes the P300, indicating that initial short-term memory storage may occur earlier than previously believed. Additionally, because C250 is so strongly predictive of a stimulus being stored in short-term memory, C250 may provide a strong index of early memory operations. Copyright © 2015 Elsevier B.V. All rights reserved.

17 CFR 250.8 - Exemption of subsidiaries subject to jurisdiction of Interstate Commerce Commission.

Science.gov (United States)

2010-04-01

... subject to jurisdiction of Interstate Commerce Commission. 250.8 Section 250.8 Commodity and Securities... to jurisdiction of Interstate Commerce Commission. Any subsidiary company of a registered holding company, which subsidiary is subject to the jurisdiction of the Interstate Commerce Commission but is not...

30 CFR 250.517 - Tubing and wellhead equipment.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Tubing and wellhead equipment. 250.517 Section... Tubing and wellhead equipment. (a) No tubing string shall be placed in service or continue to be used unless such tubing string has the necessary strength and pressure integrity and is otherwise suitable for...

30 CFR 250.511 - Traveling-block safety device.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Traveling-block safety device. 250.511 Section... Traveling-block safety device. All units being used for well-completion operations that have both a traveling block and a crown block must be equipped with a safety device that is designed to prevent the...

17 CFR 250.12 - Exemption of certain public utility companies from the definition of subsidiary companies of...

Science.gov (United States)

2010-04-01

... utility companies from the definition of subsidiary companies of holding companies. 250.12 Section 250.12... REGULATIONS, PUBLIC UTILITY HOLDING COMPANY ACT OF 1935 Registration and General Exemptions § 250.12 Exemption of certain public utility companies from the definition of subsidiary companies of holding companies...

Some basic advantages of accelerator-driven transmutation of minor actinides and iodine-129

Energy Technology Data Exchange (ETDEWEB)

Shmelev, A.N.; Apse, V.A.; Kulikov, G.G. [Moscow Engineering Physics Institute (Russian Federation)

1995-10-01

The blanket of accelerator-driven facility designed for I-129 transmutation doesn`t contain fissile and fertile materials. So the overheating of iodine compounds transmuted is practically excluded. The efficacy of I-129 transmutation is estimated. Curium being accumulated in nuclear reactors can be incinerated in blanket of accelerator-driven facility. The deep depletion of curium diluted with inert material can be achieved.

14 CFR 250.5 - Amount of denied boarding compensation for passengers denied boarding involuntarily.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Amount of denied boarding compensation for passengers denied boarding involuntarily. 250.5 Section 250.5 Aeronautics and Space OFFICE OF THE SECRETARY... boarding compensation for passengers denied boarding involuntarily. (a) Subject to the exceptions provided...

30 CFR 250.260 - What Coastal Zone Management Act (CZMA) information must accompany the DPP or DOCD?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What Coastal Zone Management Act (CZMA) information must accompany the DPP or DOCD? 250.260 Section 250.260 Mineral Resources MINERALS MANAGEMENT... Operations Coordination Documents (docd) § 250.260 What Coastal Zone Management Act (CZMA) information must...

30 CFR 250.611 - Traveling-block safety device.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Traveling-block safety device. 250.611 Section... Traveling-block safety device. After May 31, 1989, all units being used for well-workover operations which have both a traveling block and a crown block shall be equipped with a safety device which is designed...

30 CFR 250.918 - What are the CVA's primary duties during the installation phase?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are the CVA's primary duties during the installation phase? 250.918 Section 250.918 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE... appropriate (i) Loadout and initial flotation operations; (ii) Towing operations to the specified location...

Kr and Xe isotopes from spontaneous fission of 248Cm and 250Cf

International Nuclear Information System (INIS)

Srinivasan, B.

1980-01-01

Relative yields of Kr and Xe isotopes from the spontaneous fission of 248 Cm and 250 Cf have been determined mass spectrometrically. The yields are as follows: 83 Kr/ 84 Kr/ 85 Kr/ 86 Kr = 0.223/0.458/0.596/ identical 1.00 and 0.306/0.582/0.793/ identical 1.00; 131 Xe/ 134 Xe/ 136 Xe = 0.486/0.819/1.075 identical 1.00 and 0.343/0.506/0.851/ identical 1.00 from 248 Cm and 250 Cf, respectively. The Xe yields from 248 Cm agree with an earlier determination by Leich et al. Neither of these yield patterns matches that of fissiogenic Kr and Xe in carbonaceous chondrites and hence 248 Cm and 250 Cf are ruled out as progenitors of the meteoritic Kr and Xe. In general, none of the spontaneously fissioning nuclides of actinide elements can be identified as a possible progenitor. Even the mixtures of actinides, including a combination of 248 Cm and 250 Cm, are unsuitable. The origin of anomalous Kr and Xe in carbonaceous chondrites must then be traced either to the spontaneous fission of a superheavy element or to peculiarities in specific nucleosynthetic reactions. (orig.)

5 CFR 250.202 - Office of Personnel Management responsibilities.

Science.gov (United States)

2010-01-01

... REGULATIONS PERSONNEL MANAGEMENT IN AGENCIES Strategic Human Capital Management § 250.202 Office of Personnel... to which human capital management strategies are integrated into agency strategic plans and..., managers and human resources officers accountable for efficient and effective human capital management, in...

30 CFR 250.252 - What environmental monitoring information must accompany the DPP or DOCD?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What environmental monitoring information must accompany the DPP or DOCD? 250.252 Section 250.252 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... incidental take of marine mammals as may be necessary under the MMPA. (c) Flower Garden Banks National Marine...

The N250 brain potential to personally familiar and newly learned faces and objects

Directory of Open Access Journals (Sweden)

Lara Justine Pierce

2011-10-01

Full Text Available Studies employing event-related potentials (ERPs have shown that when participants are monitoring for a novel target face, the presentation of their own face elicits an enhanced negative brain potential in posterior channels approximately 250 ms after stimulus onset. Here, we investigate whether the own-face N250 effect generalizes to other highly familiar objects, specifically, images of the participant’s own dog and own car. In our experiments, participants were asked to monitor for a pre-experimentally unfamiliar target face (Joe, a target dog (Experiment 1: Joe’s Dog or a target car (Experiment 2: Joe’s Car. The target face and object stimuli were presented with non-target foils that included novel face and object stimuli, the participant’s own face, their own dog (Experiment 1 and their own car (Experiment 2. The consistent findings across the two experiments were the following: 1 the N250 potential differentiated the target faces and objects from the non-target face and object foils and 2 despite being non-targets, the own face and own objects produced an N250 response that was equal in magnitude to the target faces and objects by the end of the experiment. Thus, as indicated by its response to personally familiar and recently familiarized faces and objects, the N250 component is a sensitive index of individuated representations in visual memory.

The Varian MAT-250 mass spectrometer. Steady isotopes laboratory

International Nuclear Information System (INIS)

Hernandez M, V.; Tavera D, M.L.

1997-01-01

This work treats over the performance and applications of the Varian Mat-250 mass spectrometer which is in the environmental isotope laboratory. It can be applied over topics such as: ions formation, acceleration and collimation, ions separation, ions detection, data transformation, sampling, δ notation. (Author)

250 kV aim for hvdc valves

Energy Technology Data Exchange (ETDEWEB)

1966-06-01

Development now being carried out by ASEA is aimed at increasing the normal operating voltage for a mercury arc valve to 250 kV dc. The maximum direct voltage per valve group, with one valve in each arm of the bridge, is 125 kV for equipment already in operation in New Zealand, Japan, and Konti Scan. Valves for 130 kV and 133 kV operation are under construction for the Vancouver and the Pacific Intertie 1 links.

Characteristics and uses of a 250 kW TRIGA reactor

International Nuclear Information System (INIS)

Dimic, V.

1985-01-01

The 250 kW TRIGA Mark II reactor is a light water reactor with solid fuel elements in which the zirconium hydride moderator is homogeneously distributed between enriched uranium. Therefore the reactor has the large prompt negative temperature coefficient of reactivity, the fuel also has very high retention of radioactive fission products. The reactor core is a cylindrical configuration with an annular graphite reflector. The experimental facilities include a rotary specimen rack, a central incore radiation thimble, a pneumatic transfer system, and pulsing capability. Other experimental facilities include two radial and two tangential beam tubes, a graphite thermal column, and a graphite thermalizing column. At the steady state power of 250 kW the peak flux is 1x10 13 n/cm 2 s in the central test position. In addition, pulsing to about 2000 MW is usually provided giving peak fluxes of about 2x10 16 n/cm 2 sec. All TRIGA reactors produce a core-average thermal neutron flux of about 10 7 n.v per watt. Only with very large accelerators could such a high neutron flux be achieved. In order to give an appreciation for the research conducted at research reactors, the types of research could be summarized as follows: thermal neutron scattering, neutron radiography, neutron and nuclear physics, activation analysis, radiochemistry, biology and medicine, and teaching and training. Typical applied research with a 250 kW reactor has been conducted in medicine in biology, archeology, metallurgy and materials science, engineering and criminology. It is well known that research reactors have been used routinely to produce isotopes for industry and medicine. In some instances, reactors are the preferred method of isotope production. We can conclude that the 250 kW TRIGA research reactor is a useful and wide ranging source of radiation for basic and applied research. The operation cost for this instrument is relatively low. (author)

7 CFR 250.62 - Summer Food Service Program (SFSP).

Science.gov (United States)

2010-01-01

....62 Agriculture Regulations of the Department of Agriculture (Continued) FOOD AND NUTRITION SERVICE... Program (NSLP) and Other Child Nutrition Programs § 250.62 Summer Food Service Program (SFSP). (a... eligible for donated food support, in accordance with 7 CFR part 225. (c) Distribution of donated foods to...

Behavior Characteristics of Type I (75/25) Octol during Melt Pouring HE Warhead M250 (Chaparral)

Science.gov (United States)

1979-09-01

COVERED BEHAVIOR CHARACTERISTICS OF TYPE 1 (75/25) "OCTOL DURING MELT POURING HE WARHEAD I M250 (CHAPARRAL) 6. PERFORMING ORG. APrPORT NUMBER 7. AUTHOR...Military Specification, HMX, MIL-H-45444B, Amendment 2, dated 12 July 1977. 4 6. Military Specification, Warhead, Guided Missile, HE, M250 , Loading...CHARACTERISTICS OF TYPE i (75/25) OCTOL DURING MELT POURING HE WARHEAD M250 (CHAPARRAL) HERMAN J. FRIGAND SEPTEMBER 1979 US ARMY ARMAMENT RESEARCH AND

41 CFR 61-250.99 - What is the OMB control number for this part?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true What is the OMB control... TRAINING SERVICE, DEPARTMENT OF LABOR 250-ANNUAL REPORT FROM FEDERAL CONTRACTORS § 61-250.99 What is the OMB control number for this part? Pursuant to the Paperwork Reduction Act, 44 U.S.C. 3501 et seq., and...

30 CFR 250.104 - How may I appeal a decision made under MMS regulations?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How may I appeal a decision made under MMS... of Terms § 250.104 How may I appeal a decision made under MMS regulations? To appeal orders or decisions issued under MMS regulations in 30 CFR parts 250 to 282, follow the procedures in 30 CFR part 290. ...

Shared technologies in the development of the Titan 250 trademark gas turbine system; Anwendung bewaehrter Technologien bei der Entwicklung des Titan 250 trademark Gasturbinensystems

Energy Technology Data Exchange (ETDEWEB)

Stang, Ulrich; Knodle, Mark; Novaresi, Mark [Solar Turbines, Inc., San Diego, CA (United States); Ottoboni, Luigi [Turbomach SA, Riazzino (Switzerland)

2010-07-01

The Titan 250 gas turbine and C85 centrifugal gas compressor are the latest additions to the Solar Turbines product family. These new products leverage core technologies that have been developed and proven in several other well-established products. The Titan 250 gas turbine is a conservative hybrid design grounded in advanced aerodynamic, thermal and mechanical design tools and methodologies. It is ISO rated at 22.4 MW (30,000 HP), with a best-in-class shaft efficiency of 40% reducing fuel costs and emissions. The engine is a two-shaft design that includes a 16-stage axial flow compressor (PR 24:1), a dry low emissions combustor (<15 ppmv NOx), a two-stage gas producer turbine operating at a firing temperature of 1200 C (2200 F), and a three-stage, maximum efficiency, fully shrouded power turbine. (orig.)

76 FR 41041 - Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane, Interaction of Systems...

Science.gov (United States)

2011-07-13

... Conditions No. 25-439-SC] Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane, Interaction... special conditions are issued for the Gulfstream Aerospace LP (GALP) Model G250 airplane. This airplane...

Generation of chimeric bispecific G250/anti-CD3 monoclonal antibody, a tool to combat renal cell carcinoma

NARCIS (Netherlands)

Luiten, R. M.; Coney, L. R.; Fleuren, G. J.; Warnaar, S. O.; Litvinov, S. V.

1996-01-01

The monoclonal antibody (MAb) G250 binds to a tumour-associated antigen, expressed in renal cell carcinoma (RCC), which has been demonstrated to be a suitable target for antibody-mediated immunotherapy. A bispecific antibody having both G250 and anti-CD3 specificity can cross-link G250

30 CFR 250.1016 - Granting pipeline rights-of-way.

Science.gov (United States)

2010-07-01

... Section 250.1016 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL... process, for the assessment and management of OCS oil and gas transportation. (b) Should the proposed... comments. (d) If a proposed right-of-way crosses any lands not subject to disposition by mineral leasing or...

Separation of 248Cm (III) from 252Cf (III) and its use in time resolved fluorescence spectroscopic (TRFS) studies

International Nuclear Information System (INIS)

Murali, M.S.; Nair, A.G.C.; Gujar, R.B.; Jain, A.; Tomar, B.S.; Godbole, S.V.; Reddy, A.V.R.; Manchanda, V.K.

2008-07-01

The present report gives a description of the methodology for the separation of 248 Cm(III) from decayed 252 Cf (III) waste solution. The waste solution was first assayed for 252 Cf content by neutron counting using a neutron well coincidence counter. The sample was subjected to the chemical separation of 248 Cm (III) from 252 Cf (III) following anion and cation exchange chromatography. The alpha spectrum of the separated curium fraction showed peaks due to 246 Cm and 248 Cm while the corresponding alpha spectrum of californium fraction showed 249,250,251,252 Cf. The gamma ray abundances of 249 Cf were determined with respect to its gamma rays of 387 keV and the data agreed well with that in literature. Separated Cm(III) was further characterized by recording its time resolved fluorescence spectrum (TRFS) in aqueous medium. (author)

43 CFR 17.250 - Health, welfare, and social services.

Science.gov (United States)

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Health, welfare, and social services. 17... § 17.250 Health, welfare, and social services. This subpart applies to health, welfare, and other...) General. In providing health, welfare, or other social services or benefits, a recipient may not, on the...

17 CFR 250.44 - Sales of securities and assets.

Science.gov (United States)

2010-04-01

... not require prior Commission approval. (c) Sales pursuant to order or plan under section 11. No... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Sales of securities and assets... Various Financial Transactions 2 § 250.44 Sales of securities and assets. (a) Sales of utility securities...

Ford F250 Dedicated CNG Pickup

International Nuclear Information System (INIS)

Eudy, Leslie

1999-01-01

The U.S. Department of Energy (DOE) is encouraging the use of alternative fuels and alternative fuel vehicles (AFVs). To support this activity, DOE has directed the National Renewable Energy Laboratory (NREL) to conduct projects to evaluate the performance and acceptability of light-duty AFVs. In this study, we tested a pair of 1998 Ford F-250 pickups: one dedicated compressed natural gas (CNG) model and a gasoline model as closely matched as possible. Each vehicle was run through a series of tests to evaluate acceleration, fuel economy, braking, and cold-start capabilities, as well as more subjective performance indicators such as handling, climate control, and noise

30 CFR 250.116 - How do I determine producibility if my well is in the Gulf of Mexico?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How do I determine producibility if my well is in the Gulf of Mexico? 250.116 Section 250.116 Mineral Resources MINERALS MANAGEMENT SERVICE... Performance Standards § 250.116 How do I determine producibility if my well is in the Gulf of Mexico? If your...

UNDERWATER ANALYSIS OF IRRADIATED REACTOR SLUGS FOR Co-60 AND OTHER RADIONUCLIDES AT THE SAVANNAH RIVER SITE

International Nuclear Information System (INIS)

CASELLA, VITO

2004-01-01

Co-60 was produced in the Savannah River Site (SRS) reactors in the 1970s, and the irradiated cobalt reactor slugs were stored in a reactor basin at SRS. Since the activity rates of these slugs were not accurately known, assaying was required. A sodium iodide gamma detector was placed above a specially designed air collimator assembly, so that the slug was eight to nine feet from the detector and was shielded by the basin water. Also, 18 curium sampler slugs, used to produce Cm-244 from Pu-239, were to be disposed of with the cobalt slugs. The curium slugs were also analyzed with a High Purity Germanium (HPGE) detector in an attempt to identify any additional radionuclides produced from the irradiation. Co-60 concentrations were determined for reactor disassembly basin cobalt slugs and the 18 curium sampler slugs. The total Co-60 activity of all of the assayed slugs in this work summed to 31,783 curies on 9/15/03. From the Co-60 concentrations of the curium sampler slugs, the irradiation flux was determined for the known irradiation time. The amounts of Pu-238,-239,-240,-241,-242; Am-241,-243; and Cm-242,-244 produced were then obtained based on the original amount of Pu-239 irradiated

Radiation from a hot, thin plasma from 1 to 250 A

International Nuclear Information System (INIS)

Kato, T.

1976-01-01

A calculation of emission spectrum of a hot, low-density plasma in the region 1--250 A is presented. The mechanisms considered are electron collision-induced line emission, bremsstrahlung, and radiative recombination; and the temperature range studied is 10 5 --10 7 K. 795 lines are included. The elemental abundances of the ions of He, C, N, O, Ne, Mg, Si, S, Ca, Fe, and Ni were taken to be as in the solar corona. The line emission of Fe ions produces a maximum in the curve of an emission power between 1 and 250 A versus temperature around 10 6 K. The emission rate around 10 6 K is larger than the results calculated by Cox and Tucker and Tucker and Koren

CANDU-BLW-250

Energy Technology Data Exchange (ETDEWEB)

Pon, G A

1967-09-15

The plant 'La Centrale nucleaire de Gentilly' is located between Montreal and Quebec City on the south shore of the St. Lawrence River and start-up is scheduled for 1971. A CANDU-BLW reactor is the nuclear steam generator. his reactor utilizes a heavy water moderator, natural uranium oxide fuel, and a boiling light water coolant. To be economic, this type of plant must have a minimum light water inventory in the reactor core. A minimum inventory is obtained (a) by reducing the cross-sectional area for coolant flow to a minimum, and (b) by operating at a low-coolant density. In CANDU-BLW-250, this is accomplished by operating a closed spaced fuel rod bundle at high steam quality. These features and others in the BLW concept lead to a number of areas of concern and they are summarized below: (1) Heat Transfer: It is intended that under normal operating conditions the fuel sheaths will always be wetted with coolant. (ii) Hydrodynamic Stability: Experiments and analysis indicate that the plant has a considerable over-power capacity before instability is predicted. (iii) Control: This plant does have a positive power coefficient and the transient performance with various disturbances are detailed. (iv) Safety: The positive power coefficient leads to concern over the loss of coolant accident. The results of some accident analysis are presented. (author)

50 CFR 216.250 - Specified activity and specified geographical region.

Science.gov (United States)

2010-10-01

... OCEANIC AND ATMOSPHERIC ADMINISTRATION, DEPARTMENT OF COMMERCE MARINE MAMMALS REGULATIONS GOVERNING THE TAKING AND IMPORTING OF MARINE MAMMALS Taking Marine Mammals Incidental to Conducting Precision Strike Weapon Missions in the Gulf of Mexico § 216.250 Specified activity and specified geographical region. (a...

Consistent evaluation of neutron cross sections for the 242-244Cm isotopes

International Nuclear Information System (INIS)

Ignatyuk, A.V.; Maslov, V.M.

1989-01-01

The knowledge of neutron cross-sections for Curium isotopes is necessary for solving the problems of the external fuel cycle. Experimental information on the cross-sections is very meager and does not satisfy requirements and existing evaluations in different libraries differ substantially for fission and (n,2n) reaction cross-sections. This situation requires a critical review of the entire set of evaluations of the neutron cross-sections for Curium. 17 refs, 3 figs

CEP250 mutations associated with mild cone-rod dystrophy and sensorineural hearing loss in a Japanese family.

Science.gov (United States)

Kubota, Daiki; Gocho, Kiyoko; Kikuchi, Sachiko; Akeo, Keiichiro; Miura, Masahiro; Yamaki, Kunihiko; Takahashi, Hiroshi; Kameya, Shuhei

2018-05-02

CEP250 encodes the C-Nap1 protein which belongs to the CEP family of proteins. C-Nap1 has been reported to be expressed in the photoreceptor cilia and is known to interact with other ciliary proteins. Mutations of CEP250 cause atypical Usher syndrome which is characterized by early-onset sensorineural hearing loss (SNHL) and a relatively mild retinitis pigmentosa. This study tested the hypothesis that the mild cone-rod dystrophy (CRD) and SNHL in a non-consanguineous Japanese family was caused by CEP250 mutations. Detailed ophthalmic and auditory examinations were performed on the proband and her family members. Whole exome sequencing (WES) was used on the DNA obtained from the proband. Electrophysiological analysis revealed a mild CRD in two family members. Adaptive optics (AO) imaging showed reduced cone density around the fovea. Auditory examinations showed a slight SNHL in both patients. WES of the proband identified compound heterozygous variants c.361C>T, p.R121*, and c.562C>T, p.R188* in CEP250. The variants were found to co-segregate with the disease in five members of the family. The variants of CEP250 are both null variants and according to American College of Medical Genetics and Genomics (ACMG) standards and guideline, these variants are classified into the very strong category (PVS1). The criteria for both alleles will be pathogenic. Our data indicate that mutations of CEP250 can cause mild CRD and SNHL in Japanese patients. Because the ophthalmological phenotypes were very mild, high-resolution retinal imaging analysis, such as AO, will be helpful in diagnosing CEP250-associated disease.

Characterization of Aging Behavior in M250 Grade Maraging Steel Using Ultrasonic Measurements

Science.gov (United States)

Rajkumar, K. V.; Kumar, Anish; Jayakumar, T.; Raj, Baldev; Ray, K. K.

2007-02-01

Ultrasonic measurements have been carried out in M250 grade maraging steel specimens subjected to solution annealing at 1093 K for 1 hour followed by aging at 755 K for various durations in the range of 0.25 to 100 hours. The influence of aging on microstructure, room temperature hardness, and ultrasonic parameters (longitudinal and shear wave velocities and Poisson’s ratio) has been studied in order to derive correlations among these parameters in aged M250 maraging steel. Both hardness and ultrasonic velocities exhibit almost similar behaviors with aging time. They increase with the precipitation of intermetallic phases, Ni3Ti and Fe2Mo, and decrease with the reversion of martensite to austenite. Ultrasonic shear wave velocity is found to be more influenced by the precipitation of intermetallic phases, whereas longitudinal wave velocity is influenced more by the reversion of martensite to austenite. Unlike hardness and ultrasonic velocities, the Poisson’s ratio exhibits a monotonous decrease with aging time and, hence, can be used for unambiguous monitoring of the aging process in M250 maraging steel. Further, none of the parameters, i.e., hardness, ultrasonic velocity, or Poisson’s ratio, alone could identify the initiation of the reversion of austenite at early stage; however, the same could be identified from the correlation between ultrasonic velocity and Poisson’s ratio, indicating the advantage of using the multiparametric approach for comprehensive characterization of complex aging behavior in M250 grade maraging steel.

On rolling of alloyed steels on the continuous light-section mill 250

International Nuclear Information System (INIS)

Grigor'ev, V.K.; Antipov, V.F.; Zamotin, V.M.; Kuznetsov, Yu.M.

1976-01-01

Using the method of computed ratios, the expected loads (torques) have been calculated in the rolling of alloyed steels on the light-section mill 250 of the Chelyabinsk metallurgical works. The deviation of the computed torques from those measured for steels 35GS and St5ps does not exceed -6%. Data are given on changes in torques during the rolling of alloyed steels in the different stands as compared with the actual data for the rolling of ordinary steel. Calculations show, and experimental data confirm, that, according to the torque value, it is possible to roll alloyed steels of sufficiently wide assortment on mill 250

21 CFR 250.108 - Potassium permanganate preparations as prescription drugs.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Potassium permanganate preparations as... or Prescription Status of Specific Drugs § 250.108 Potassium permanganate preparations as... women resulting from the misuse of potassium permanganate in an effort to induce abortion. Reports from...

Production of charmonium in 250 GeV μ+-iron interactions

International Nuclear Information System (INIS)

Aubert, J.J.; Dobinson, R.W.; Dosselli, U.; Edwards, A.; Gabathuler, E.; Gregory, P.; Haas, J.; Leenen, M.; Montgomery, H.E.; Osborne, A.M.; Bassompierre, G.; Bouard, X. de; Broll, C.; Coignet, G.; Crespo, J.M.; Declais, Y.; Favier, J.; Maire, M.; Massonnet, L.; Minssieux, H.; Payre, P.; Pessard, H.; Schneegans, M.; Thenard, J.M.; Urban, L.; Becks, K.H.; Boehm, E.; Brown, S.; Cobb, J.H.; Combley, F.; D'Agostini, G.; Dalpiaz, P.F.; Dalpiaz, P.; Dau, W.D.; Davies, J.K.; Drees, J.; Ferrero, M.I.; Gamet, R.; Gerhardt, V.; Hamacher, K.; Hayman, P.; Henckes, M.; Landgraf, U.; Mohr, W.; Moser, K.; Mount, R.P.; McNicholas, J.; Peroni, C.; Pietrzyk, U.; Rith, K.; Sloan, T.; Stier, H.E.; Stockhausen, W.; Villers, M.; Wahlen, H.; Whalley, M.; Williams, D.; Williams, W.S.C.; Williamson, J.; Wimpenny, S.J.

1983-01-01

The production of J/psi and psi' has been measured in 250 GeV muon iron interactions. The measured total cross sections are sigma(μN-> μJ/psiX) = 0.74 +- 0.14 nb and sigma (μN->μpsi'X) =0.16 +-. (orig.)

75 FR 62919 - Notice of Final Federal Agency Actions on the Route 250 Bypass Interchange at McIntire Road...

Science.gov (United States)

2010-10-13

... on the Route 250 Bypass Interchange at McIntire Road Project in Virginia AGENCY: Federal Highway.... 139(l)(1). The actions relate to the Route 250 Bypass Interchange at McIntire Road project in the City... Virginia: Route 250 Bypass Interchange at McIntire Road. The project would involve construction of a grade...

20 CFR 410.250 - Effect of conviction of felonious and intentional homicide on entitlement to benefits.

Science.gov (United States)

2010-04-01

... intentional homicide on entitlement to benefits. 410.250 Section 410.250 Employees' Benefits SOCIAL SECURITY... conviction of felonious and intentional homicide on entitlement to benefits. An individual who has been finally convicted by a court of competent jurisdiction of the felonious and intentional homicide of a...

30 CFR 250.213 - What general information must accompany the EP?

Science.gov (United States)

2010-07-01

... description and discussion of any new or unusual technology (see definition under § 250.200) you will use to... hydrocarbons. Include the estimated flow rate, total volume, and maximum duration of the potential blowout...

30 CFR 250.191 - How does MMS conduct incident investigations?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How does MMS conduct incident investigations... Reporting Requirements § 250.191 How does MMS conduct incident investigations? Any investigation that MMS... meetings conducted by a chairperson appointed by MMS. The following requirements apply to any panel...

76 FR 25229 - Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane, Dynamic Test Requirements...

Science.gov (United States)

2011-05-04

... Memorandum ``Side-Facing Seats on Transport Category Airplanes'' and draft Issue Paper ``Dynamic Test...; Special Conditions No. 25-425-SC] Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane... are issued for the Gulfstream Aerospace LP (GALP) model G250 airplane. This airplane will have a novel...

30 CFR 250.523 - How long do I keep records of casing pressure and diagnostic tests?

Science.gov (United States)

2010-07-01

... and diagnostic tests? 250.523 Section 250.523 Mineral Resources MINERALS MANAGEMENT SERVICE... casing pressure and diagnostic tests? Records of casing pressure and diagnostic tests must be kept at the field office nearest the well for a minimum of 2 years. The last casing diagnostic test for each casing...

A randomized trial of three copper IUDs (MLCu250, MLCu375 and Nova-T).

Science.gov (United States)

Bratt, H; Skjeldestad, F E; Cullberg Valentin, K

1988-01-01

A randomized prospective trial of three copper IUDs, Nova-T, MLCu375 and MLCu250, including 200 of each, is presented. Insertion was done at the hospital outpatient clinic on normally menstruating women and on women in puerperio. Follow-up was scheduled after 12, 24 and 36 months. Pregnancy rates were low for all 3 models. Pearl indices after 3 years were 0.5, 0.9 and 0.8 for Nova-T, MLCu375 and MLCu250 respectively (NS). Abnormal bleeding and/or pain was the most frequent termination cause. Minor differences in the termination rates because of abnormal bleeding and/or pain were found and are discussed. The continuation rates based on all medically relevant IUD removals were 74%, 73% and 81% after 3 years for Nova-T, MLCu375 and MLCu250 respectively. No important difference in clinical performance between the three copper IUDs could be demonstrated.

30 CFR 250.414 - What must my drilling prognosis include?

Science.gov (United States)

2010-07-01

...) Projected plans for logging; (c) Planned safe drilling margin between proposed drilling fluid weights and... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must my drilling prognosis include? 250... OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations...

CANDU-BLW-250

Energy Technology Data Exchange (ETDEWEB)

Pon, G. A. [Atomic Energy of Canada Ltd, Sheridan Park, ON (Canada)

1968-04-15

The plant ''La Centrale nucleaire de Gentiliy'' is located between Montreal and Quebec City on the south shore of the St. Lawrence River. Startup is scheduled for 1971. A CANDU-BLW reactor is the nuclear steam generator. This reactor utilizes a heavy-water moderator, natural uranium oxide fuel, and a boiling light-water coolant. To be economic, this type of plant must have a minimum light-water inventory in the reactor core. A minimum inventory is obtained (a) by reducing the cross-sectional area for coolant flow to a minimum, and (b) by operating at a low coolant density. In CANDU-BLW-250, this is accomplished by operating a closed spaced fuel rod bundle at high steam quality. These features and others in the BLW concept lead to a number of areas of concern and they are summarized below: (i) Heat transfer. It is intended that under normal operating conditions the fuel sheaths will always be wetted with coolant. Some experiments and backup calculations are presented to support this specification. (ii) Hydrodynamic stability. Experiments and analysis indicate that the plant has a considerable over-power capacity before instability is predicted. (iii) Control. This plant does have a positive power coefficient and the transient performance with various disturbances is detailed. (iv) Safety. The positive power coefficient leads to concern over the loss of coolant accident. The results of some accident analyses are presented. (author)

MHD repowering of a 250 MWe unit of the TVA Allen Steam Plant

International Nuclear Information System (INIS)

Chapman, J.N.; Attig, R.C.

1992-01-01

In this paper coal fired MHD repowering is considered for the TVA Allen Steam Plant. The performance of the repowered plant is presented. Cost comparisons are made of the cost of repowering with MHD versus the cost of meeting similar standards by installing scrubbers and selective catalytic NO x reduction (SCNR). For repowering of a single 250 MW e unit, the costs favor scrubbing and SCNR. If one considers a single repowering of all three 250 MW e units by a single MHD topping cycle and boiler, MHD repowering is more economical. Environmental emissions from the repowered plant are estimated

30 CFR 250.187 - What are MMS' incident reporting requirements?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are MMS' incident reporting requirements... Reporting Requirements § 250.187 What are MMS' incident reporting requirements? (a) You must report all... other permit issued by MMS, and that are related to operations resulting from the exercise of your...

30 CFR 250.119 - Will MMS approve subsurface gas storage?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Will MMS approve subsurface gas storage? 250....119 Will MMS approve subsurface gas storage? The Regional Supervisor may authorize subsurface storage of gas on the OCS, on and off-lease, for later commercial benefit. To receive MMS approval you must...

Transuranium Processing Plant semiannual report of production, status, and plans for period ending December 31, 1975

International Nuclear Information System (INIS)

King, L.J.; Bigelow, J.E.; Collins, E.D.

1976-10-01

Between July 1, 1975, and December 31, 1975, maintenance was conducted at TRU for a period of three months, 295 g of curium oxide (enough for approximately 26 HFIR targets) were prepared, 100 mg of high-purity 248 Cm, were separated from 252 Cf that had been purified during earlier periods, 11 HFIR targets were fabricated, and 28 product shipments were made. No changes were made in the chemical processing flowsheets normally used at TRU during this report period. However, three equipment racks were replaced (with two new racks) during this time. In Cubicle 6, the equipment replaced was that used to decontaminate the transplutonium elements from rare earth fission products and to separate curium from the heavier elements by means of the LiCl-based anion-exchange process. In Cubicle 5, the equipment used to separate the transcurium elements by high-pressure ion exchange and to purify berkelium by batch solvent extraction was replaced. Two neutron sources were fabricated, bringing the total fabricated to 79. One source that had been used in a completed project was returned to the TRU inventory and is available for reissue. Three sources, for which no further use was foreseen, were processed to isolate and recover the ingrown 248 Cm and the residual 252 Cf. Eight pellets, each containing 100 μg of high-purity 248 Cm were prepared for irradiation in HFIR to study the production of 250 Cm. The values currently being used for transuranium element decay data and for cross-section data in planning irradiation-processing cycles, calculating production forecasts, and assaying products are tabulated

Binary energy source of the HH 250 outflow and its circumstellar environment

Science.gov (United States)

Comerón, Fernando; Reipurth, Bo; Yen, Hsi-Wei; Connelley, Michael S.

2018-04-01

Aims: Herbig-Haro flows are signposts of recent major accretion and outflow episodes. We aim to determine the nature and properties of the little-known outflow source HH 250-IRS, which is embedded in the Aquila clouds. Methods: We have obtained adaptive optics-assisted L-band images with the NACO instrument on the Very Large Telescope (VLT), together with N- and Q-band imaging with VISIR also on the VLT. Using the SINFONI instrument on the VLT we carried out H- and K-band integral field spectroscopy of HH 250-IRS, complemented with spectra obtained with the SpeX instrument at the InfraRed Telescope Facility (IRTF) in the JHKL bands. Finally, the SubMillimeter Array (SMA) interferometer was used to study the circumstellar environment of HH 250-IRS at 225 and 351 GHz with CO (2-1) and CO (3-2) maps and 0.9 mm and 1.3 mm continuum images. Results: The HH 250-IRS source is resolved into a binary with 0.''53 separation, corresponding to 120 AU at the adopted distance of 225 pc. The individual components show heavily veiled spectra with weak CO absorption indicative of late-type stars. Both are Class I sources, but their spectral energy distributions between 1.5 μm and 19 μm differ markedly and suggest the existence of a large cavity around one of the components. The millimeter interferometric observations indicate that the gas mainly traces a circumbinary envelope or disk, while the dust emission is dominated by one of the circumstellar envelopes. Conclusions: HH 250-IRS is a new addition to the handful of multiple systems where the individual stellar components, the circumstellar disks and a circumbinary disk can be studied in detail, and a rare case among those systems in which a Herbig-Haro flow is present. Based on observations obtained with the VLT (Cerro Paranal, Chile) in programs 089.C-0196(A), 095.C-0488(A), and 095.C-0488(B), as well as with IRTF (Mauna Kea, Hawaii), SMA (Mauna Kea, Hawaii), and the Nordic Optical Telescope (La Palma, Canary Islands, Spain

30 CFR 250.261 - What environmental impact analysis (EIA) information must accompany the DPP or DOCD?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What environmental impact analysis (EIA) information must accompany the DPP or DOCD? 250.261 Section 250.261 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Contents of...

Oral administration of type-II collagen peptide 250-270 suppresses specific cellular and humoral immune response in collagen-induced arthritis.

Science.gov (United States)

Zhu, Ping; Li, Xiao-Yan; Wang, Hong-Kun; Jia, Jun-Feng; Zheng, Zhao-Hui; Ding, Jin; Fan, Chun-Mei

2007-01-01

Oral antigen is an attractive approach for the treatment of autoimmune and inflammatory diseases. Establishment of immune markers and methods in evaluating the effects of antigen-specific cellular and humoral immune responses will help the application of oral tolerance in the treatment of human diseases. The present article observed the effects of chicken collagen II (CII), the recombinant polymerized human collagen II 250-270 (rhCII 250-270) peptide and synthesized human CII 250-270 (syCII 250-270) peptide on the induction of antigen-specific autoimmune response in rheumatoid arthritis (RA) peripheral blood mononuclear cells (PBMC) and on the specific cellular and humoral immune response in collagen-induced arthritis (CIA) and mice fed with CII (250-270) prior to immunization with CII. In the study, proliferation, activation and intracellular cytokine production of antigen-specific T lymphocytes were simultaneously analyzed by bromodeoxyuridine (BrdU) incorporation and flow cytometry at the single-cell level. The antigen-specific antibody and antibody-forming cells were detected by ELISA and ELISPOT, respectively. CII (250-270) was found to have stimulated the response of specific lymphocytes in PBMC from RA patients, including the increase expression of surface activation antigen marker CD69 and CD25, and DNA synthesis. Mice, fed with CII (250-270) before CII immunization, had significantly lower arthritic scores than the mice immunized with CII alone, and the body weight of the former increased during the study period. Furthermore, the specific T cell activity, proliferation and secretion of interferon (IFN)-gamma in spleen cells were actively suppressed in CII (250-270)-fed mice, and the serum anti-CII, anti-CII (250-270) antibody activities and the frequency of specific antibody-forming spleen cells were significantly lower in CII (250-270)-fed mice than in mice immunized with CII alone. These observations suggest that oral administration of CII (250-270) can

30 CFR 250.1507 - How will MMS measure training results?

Science.gov (United States)

2010-07-01

... program, using one or more of the methods in this section. (a) Training system audit. MMS or its... how effective the training was. (c) Employee or contract personnel testing. MMS or its authorized... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How will MMS measure training results? 250.1507...

JPRS Report, Science & Technology, USSR: Space.

Science.gov (United States)

1988-08-17

Half-life, years Specific Heat Release W/hr Plutonium-238 87.5 0.46 Curium-244 18.4 2.8 Curium-242 0.45 120 Polonium - 210 0.38 144 Polonium - 210 ...begun train- ing a year before the flight. The prospective space travelers had to be trained to stay in a special capsule and to use nozzles for food ...conditions of extended weight- lessness. On command, the animals are given food and water, waste is removed, and day/night conditions are regulated

Mechanical design of a 250 kilogauss solenoidal magnet

International Nuclear Information System (INIS)

Bonanos, P.

1975-12-01

The mechanical design and construction of a 5 cm bore, 23 cm long solenoidal magnet operated at 250 kilogauss is described. The magnet provides confining field for a plasma heated by a CO 2 laser. Radial diagnostic ports with a clear aperture of 0.41 cm allow viewing access near the magnet midplane. The on-axis field homogeneity is within 5 percent over a central length of 12 cm. The magnet sustained 500 to 1000 pulses at the highest field levels before catastrophic failure

A Theoretical and Experimental Analysis of Post-Compression Water Injection in a Rolls-Royce M250 Gas Turbine Engine

Science.gov (United States)

2015-05-18

ROLLS-ROYCE M250 GAS TURBINE ENGINE by Midshipman 1/C Brian R. He United States Naval Academy Annapolis, Maryland...Injection in a Rolls- Royce M250 Gas Turbine Engine 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) He...output, efficiency, operating conditions, and emissions of injecting water at the compressor discharge of a Rolls-Royce M250 . The results

Towards 250 m mapping of terrestrial primary productivity over Canada

Science.gov (United States)

Gonsamo, A.; Chen, J. M.

2011-12-01

Terrestrial ecosystems are an important part of the climate and global change systems. Their role in climate change and in the global carbon cycle is yet to be well understood. Dataset from satellite earth observation, coupled with numerical models provide the unique tools for monitoring the spatial and temporal dynamics of territorial carbon cycle. The Boreal Ecosystems Productivity Simulator (BEPS) is a remote sensing based approach to quantifying the terrestrial carbon cycle by that gross and net primary productivity (GPP and NPP) and terrestrial carbon sinks and sources expressed as net ecosystem productivity (NEP). We have currently implemented a scheme to map the GPP, NPP and NEP at 250 m for first time over Canada using BEPS model. This is supplemented by improved mapping of land cover and leaf area index (LAI) at 250 m over Canada from MODIS satellite dataset. The results from BEPS are compared with MODIS GPP product and further evaluated with estimated LAI from various sources to evaluate if the results capture the trend in amount of photosynthetic biomass distributions. Final evaluation will be to validate both BEPS and MODIS primary productivity estimates over the Fluxnet sites over Canada. The primary evaluation indicate that BEPS GPP estimates capture the over storey LAI variations over Canada very well compared to MODIS GPP estimates. There is a large offset of MODIS GPP, over-estimating the lower GPP value compared to BEPS GPP estimates. These variations will further be validated based on the measured values from the Fluxnet tower measurements over Canadian. The high resolution GPP (NPP) products at 250 m will further be used to scale the outputs between different ecosystem productivity models, in our case the Canadian carbon budget model of Canadian forest sector CBM-CFS) and the Integrated Terrestrial Ecosystem Carbon model (InTEC).

DCU 250 Arabic dependency bank: an LFG gold standard resource for the Arabic Penn treebank

OpenAIRE

Al-Raheb, Yafa; Akrout, Amine; van Genabith, Josef; Dichy, J.

2006-01-01

This paper describes the construction of a dependency bank gold standard for Arabic, DCU 250 Arabic Dependency Bank (DCU 250), based on the Arabic Penn Treebank Corpus (ATB) (Bies and Maamouri, 2003; Maamouri and Bies, 2004) within the theoretical framework of Lexical Functional Grammar (LFG). For parsing and automatically extracting grammatical and lexical resources from treebanks, it is necessary to evaluate against established gold standard resources. Gold standards for various languages h...

On the economic dimensions of CSR: Exploring Fortune Global 250 reports

NARCIS (Netherlands)

Fortanier, F.N.; Kolk, A.

2007-01-01

The macro-level debate on the economic impact of multinational enterprises (MNEs) is still unsettled. This article explores micro-level evidence by examining what Fortune Global 250 firms themselves report about their economic impact. Such reporting embodies corporate attempts to account for their

Root uptake of transuranic elements

International Nuclear Information System (INIS)

Schulz, R.K.

1977-01-01

The uptake of elements by plant roots is one of the important pathways of entry of many elements into the food chain of man. Data are cited showing plutonium concentration ratios, plant/soil, ranging from 10 -10 to 10 -3 . Concentration ratios for americium range from 10 -7 to 10 +1 . Limited experiments with curium and neptunium indicate that root uptake of curium is similar to that of americium and that plant uptake of neptunium is substantially larger than that of curium and americium. The extreme ranges of concentration ratios cited for plutonium and americium are due to a number of causes. Experimental conditions such as very intensive cropping will lead to abnormally high concentration ratios. In some experiments, addition of chelating agents markedly increased plant root uptake of transuranic elements. Particle size and composition of the source material influenced uptake of the transuranics by plants. Translocation within the plant, and soil factors such as pH and organic matter content, all affect concentration ratios

Studies of selected transuranium and lanthanide tri-iodides under pressure using absorption spectrophotometry

International Nuclear Information System (INIS)

Haire, R.G.; Young, J.P.; Peterson, J.R.; Tennessee Univ., Knoxville; Benedict, U.

1987-01-01

The anhydrous tri-iodides of plutonium, americium and curium under pressure have been investigated using absorption spectrophotometry. These initial studies on plutonium and curium tri-iodides together with the published data for americium tri-iodide show that the rhombohedral form of these compounds (BiI 3 -type structure) can be converted to the orthorhombic form (PuBr 3 -type structure) by applying pressure at room temperature. Absorption spectrophotometry can often differentiate between two crystallographic forms of a material and has been used in the present high-pressure studies to monitor the effects of pressure on the tri-iodides. A complication in these studies of the tri-iodides is a significant shift of their absorption edges with pressure from the near UV to the visible spectral region. With curium tri-iodide this shift causes interference with the major f-f absorption peaks and precludes identification by absorption spectrophotometry of the high pressure phase of CmI 3 . (orig.)

Criticality and thermal analyses of separated actinides

International Nuclear Information System (INIS)

Bakker, E.

2004-01-01

Curium and americium pose special problems in the chemical preparation of spent fuel for transmutation. Once separated from the other actinides, the isotopes can lead to nuclear fission with the subsequent release of a large amount of radiation. A neutron criticality code was used to determine k eff for varying quantities of Cm 2 O 3 and Am 2 O 3 held within spherical or cylindrical containers. These geometries were investigated both in air and in water. Recommendations are made on the maximum amount of Cm 2 O 3 and Am 2 O 3 that can be safely stored or handled before encountering criticality. Several isotopes of curium and americium also generate a significant amount of heat by radioactive decay. If kilogram quantities are stored in a container, for example, the material may heat to an equilibrium temperature that exceeds its melting temperature. The heat generation of curium and americium present even more restriction on the mass of that can safely be contained in one location. (author)

Theoretical and experimental evaluation of waste transport in selected rocks: 1977 annual report of LBL Contract No. 45901AK. Waste Isolation Safety Assessment Program: collection and generation of transport data

International Nuclear Information System (INIS)

Apps, J.A.; Benson, L.V.; Lucas, J.; Mathur, A.K.; Tsao, L.

1977-09-01

During fiscal year 1977, the following subtasks were performed. (1) Thermodynamic data were tabulated for those aqueous complexes and solid phases of plutonium, neptunium, americium, and curium likely to form in the environment. (2) Eh-pH diagrams were computed and drafted for plutonium, neptunium, americium and curium at 25 0 C and one atmosphere. (3) The literature on distribution coefficients of plutonium, neptunium, americium, and curium was reviewed. (4) Preliminary considerations were determined for an experimental method of measuring radionuclide transport in water-saturated rocks. (5) The transport mechanisms of radionuclides in water-saturated rocks were reviewed. (6) A computer simulation was attempted of mass transfer involving actinides in water-saturated rocks. Progress in these tasks is reported. Subtasks 1, 2, 3, and 4 are complete. The progress made in subtask 5 is represented by an initial theoretical survey to define the conditions needed to characterize the transport of radionuclides in rocks. Subtask 6 has begun but is not complete

Anti-inflammatory effects of salmeterol/fluticasone propionate 50/250 mcg combination therapy in Japanese patients with chronic obstructive pulmonary disease

Directory of Open Access Journals (Sweden)

Asai K

2015-04-01

Full Text Available Kazuhisa Asai,1 Akihiro Kobayashi,2 Yukio Makihara,3 Malcolm Johnson4 1Department of Respiratory Medicine, Graduate School of Medicine, Osaka City University, Osaka, Japan; 2Biomedical Data Sciences, 3Medical Affairs Respiratory Department, GlaxoSmithKline, Tokyo, Japan; 4Respiratory Global Franchise, GlaxoSmithKline, Uxbridge, UK Purpose: Using sputum neutrophils as the primary measure, and other inflammation biomarkers, this study evaluated the anti-inflammatory effects of the combination salmeterol 50 mcg and fluticasone propionate 250 mcg (SFC 250 in Japanese patients with chronic obstructive pulmonary disease (COPD. Patients and methods: Patients were treated in a randomized, double-blind, parallel group, placebo-controlled trial with SFC 250 twice daily (n=26 or placebo (n=26 for 12 weeks. At the start and end of treatment, inflammation biomarkers (sputum and serum, lung function, and health status (COPD Assessment Test [CAT] questionnaire were measured. Results: Although a numerical decrease in differential neutrophil count was observed from baseline, SFC 250 did not significantly reduce sputum neutrophils compared with placebo, nor were there significant changes from baseline in the other biomarkers (sputum or serum, lung function, or CAT, versus placebo. Squamous epithelial cell contamination in some sputum samples rendered them unacceptable for analysis, which reduced the sample size to n=19 (SFC 250 and n=10 (placebo. However, inclusion of contaminated samples did not affect the overall trend of the outcome. Ad hoc bootstrap statistical analysis showed a 27.9% (SFC 250 and 1.3% (placebo decrease in sputum neutrophils. Sputum IL-8 decreased by 43.2% after SFC 250 but increased by 48.3% with placebo. Responder analyses showed 42% of patients had ≥20% decrease in neutrophils from baseline; and 47% of patients had a ≥200 pg/mL change in sputum IL-8 following SFC 250 versus 20% after placebo; both changes are considered clinically

Search for charm in 250 GeV/c π-p interactions

International Nuclear Information System (INIS)

Bogert, D.; Hanft, R.; Albright, J.R.

1975-10-01

A study was made of the reaction π - + p at 250 GeV/c in order to search for charmed particles. Cross sections, effective mass distributions, and an upper limit for each decay mode were found. However, no evidence was found for charmed particles

Spectroscopic and thermodynamic studies on the complexation of trivalent curium with inorganic ligands at increased temperatures; Spektroskopische und thermodynamische Untersuchungen zur Komplexierung von trivalentem Curium mit anorganischen Liganden bei erhoehten Temperaturen

Energy Technology Data Exchange (ETDEWEB)

Skerencak, Andrej

2010-05-11

The subject of the present investigation is the complexation of trivalent actinides at elevated temperatures. The objective of this work is to broaden the comprehension of the geochemical processes relevant for the migration of radionuclides in the near-field of a nuclear waste repository. Depending on the disposed nuclear waste, the temperature in the direct vicinity of a nuclear waste repository may reach up to 200 C. The result is a distinct change of the geochemistry of the actinides. Many of these processes have already been studied in detail at room temperature. Yet, data at elevated temperature are rare. However, a comprehensive long term safety analysis of a nuclear waste repository requires the precise thermodynamic description of the relevant geochemical processes at room as well as at elevated temperatures. The present work is focused on the investigation of the complexation of trivalent curium (Cm(III)) with different inorganic ligands at elevated temperatures. Due to its outstanding spectroscopic properties, Cm(III) is chosen as a representative for trivalent actinides. The studied ligand systems are nitrate (NO{sub 3}{sup -}), fluoride (F{sup -}), sulphate (SO{sub 4}{sup 2-}) and chloride (Cl{sup -}). The main analytical method employed is the ''time resolved laser fluorescence spectroscopy'' (TRLFS). The experiments with nitrate, sulphate and chloride were carried out in a custom-built high temperature cell, enabling spectroscopic studies at temperatures up to 200 C. The Cm(III)-fluoride-system was studied in a cuvette (quartz glass) in the temperature range from 20 to 90 C. Supplementary structural studies were performed using EXAFS (Extended X-Ray Absorption Fine Structure) spectroscopy and supported by quantum chemical calculations at DFT (Density Functional Theory) level. The results of the TRLFS studies show a general shift of the chemical equilibrium towards the complexed species with increasing temperature. For instance

Efficient high-throughput biological process characterization: Definitive screening design with the ambr250 bioreactor system.

Science.gov (United States)

Tai, Mitchell; Ly, Amanda; Leung, Inne; Nayar, Gautam

2015-01-01

The burgeoning pipeline for new biologic drugs has increased the need for high-throughput process characterization to efficiently use process development resources. Breakthroughs in highly automated and parallelized upstream process development have led to technologies such as the 250-mL automated mini bioreactor (ambr250™) system. Furthermore, developments in modern design of experiments (DoE) have promoted the use of definitive screening design (DSD) as an efficient method to combine factor screening and characterization. Here we utilize the 24-bioreactor ambr250™ system with 10-factor DSD to demonstrate a systematic experimental workflow to efficiently characterize an Escherichia coli (E. coli) fermentation process for recombinant protein production. The generated process model is further validated by laboratory-scale experiments and shows how the strategy is useful for quality by design (QbD) approaches to control strategies for late-stage characterization. © 2015 American Institute of Chemical Engineers.

7 CFR 250.59 - Storage and inventory management of donated foods.

Science.gov (United States)

2010-01-01

... 7 Agriculture 4 2010-01-01 2010-01-01 false Storage and inventory management of donated foods. 250... management of donated foods. (a) General requirements. Distributing agencies, subdistributing agencies, and... management system, as defined in this part, unless the distributing agency requires donated foods to be...

7 CFR 250.14 - Warehousing, distribution and storage of donated foods.

Science.gov (United States)

2010-01-01

.... (iv) All initial data regarding the cost of the current warehousing and distribution system and the... 7 Agriculture 4 2010-01-01 2010-01-01 false Warehousing, distribution and storage of donated foods... General Operating Provisions § 250.14 Warehousing, distribution and storage of donated foods. (a...

Experimental ethylene oxide neuropathy. Chronic exposure to 250 ppm in rats

Energy Technology Data Exchange (ETDEWEB)

Ohnishi, A.; Yamamoto, T.; Inoue, N.; Tanaka, I.; Koga, M.

1985-12-01

In Wistar rats subjected to a six-hour exposure to ethylene oxide (ETO) at the concentration of 250 parts per million once a day, five times a week for 9 months, histopathologic studies of myelinated fibers of the proximal sural, distal sural and peroneal nerves and of the fasciculus gracilis at the fifth thoracic and third cervical segments of the spinal cord were performed to reveal whether ETO of such concentration produces the degeneration of the primary sensory neuron. Throughout the study, no definite abnormality of the gait or posture was observed in both control and test rats. Qualitative histologic studies disclosed preferential distal axonal degeneration of myelinated fibers in both sural nerves and gracile fascicles in test rats, although the extent of the distribution and the severity of the degenerative findings were variable among test rats. Therefore, it was concluded that exposure to 250 ppm ethylene oxide produces central-peripheral distal axonal degeneration of the primary sensory neuron in rats.

12 CFR 250.402 - Service as officer, director, or employee of licensee corporation under the Small Business...

Science.gov (United States)

2010-01-01

... licensee corporation under the Small Business Investment Act of 1958. 250.402 Section 250.402 Banks and... employee of licensee corporation under the Small Business Investment Act of 1958. (a) The Board of... corporation under the Small Business Investment Act of 1958 (15 U.S.C. 661 et seq.). It is understood that a...

Evaluation of the Meditech M250 and a comparison with other CT scanners

Energy Technology Data Exchange (ETDEWEB)

Greensmith, R.; Richardson, R.B.; Mackintosh, I.P.; Sargood, A.J.; Stevens, P.H.

1985-11-01

The Meditech M250 computerised tomography (CT) machine was evaluated during the first half of 1984. Measurements were made of noise, modulation transfer function, slice width, radiation dose profile, uniformity and linearity of CT number, effective photon energy and parameters relating to machine specification, such as pixel size and scan time. All breakdowns were logged to indicate machine reliability. A comparison with the established EMI CT1010 and CT5005 was made for noise, resolution and multislice radiation dose, as well as the dose efficiency or quality (Q) factor for both head and body modes of operation. The M250 was found to perform to its intended specification with an acceptable level of reliability.

30 CFR 250.901 - What industry standards must your platform meet?

Science.gov (United States)

2010-07-01

...) American Petroleum Institute (API) Bulletin 2INT-DG, Interim Guidance for Design of Offshore Structures for... (RP) 2A-WSD, RP for Planning, Designing, and Constructing Fixed Offshore Platforms—Working Stress..., (incorporated by reference as specified in § 250.198); (15) American Society for Testing and Materials (ASTM...

33 CFR 110.250 - St. Thomas Harbor, Charlotte Amalie, V.I.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false St. Thomas Harbor, Charlotte... SECURITY ANCHORAGES ANCHORAGE REGULATIONS Anchorage Grounds § 110.250 St. Thomas Harbor, Charlotte Amalie.... Thomas, V.I. of the United States and approaches thereto, including all waters under its jurisdiction, as...

Electron beam dynamics in the LIU-30/250 accelerator

International Nuclear Information System (INIS)

Vakhrushin, Yu.P.; Kuznetsov, V.S.; Tikhomirov, A.S.

1989-01-01

Results of numerical simulation of coherent oscillations of electron beam in the LIU-30/250 accelerating system are presented. Transport systems both with continuous field and the discrete ones are considered. The following conclusions are made: amplitude of coherent oscillations inevitably grows in the real transport channel; the presence of correctors can lead to sufficient losses of beam pulse duration; discrete system is the optimal system for beam transport without sufficient losses. 7 refs.; 3 figs

The Novel N-Substituted Benztropine Analog GA2-50 Possesses Pharmacokinetic and Pharmacodynamic Profiles Favorable for a Candidate Substitute Medication for Cocaine Abuse

Science.gov (United States)

OTHMAN, AHMED A.; NEWMAN, AMY H.; EDDINGTON, NATALIE D.

2009-01-01

GA2-50 is a novel N-substituted benztropine analog with improved potency and selectivity for the dopamine transporter. The pharmacokinetic and pharmacodynamic properties of GA2-50 were characterized as a part of its preclinical evaluation as a substitute medication for cocaine abuse. In vitro transport and metabolism studies as well as pharmacokinetic studies in rats were conducted. Effect of GA2-50 on the extracelluar nucleus accumbens (NAc) dopamine levels and on cocaine’s induced dopamine elevation was evaluated using intracerebral microdialysis. GA2-50 showed high transcellular permeability despite being a P-glycoprotein substrate. GA2-50 was a substrate of human CYP2D6, CYP2C19, CYP2E1, rat CYP2C11, CYP2D1, CYP3A1, and CYP1A2; with low intrinsic clearance values. In vivo, GA2-50 showed high brain uptake (Ri ~ 10), large volume of distribution (Vss =37 L/kg), and long elimination half-life (t½ =19 h). GA2-50 resulted in 1.6- and 2.7-fold dopamine elevation at the 5 and 10 mg/kg i.v. doses. Dopamine elevation induced by GA2-50 was significantly reduced, slower and longer lasting than previously observed for cocaine. GA2-50 had no significant effect on cocaine’s induced dopamine elevation upon simultaneous administration. Results from the present study indicate that GA2-50 possesses several attributes sought after for a substitute medication for cocaine abuse. PMID:18425847

Estabilidad acelerada de tabletas de levodopa-carbidopa (250-25 mg

Directory of Open Access Journals (Sweden)

Mirna Fernández Cervera

2001-08-01

Full Text Available Se realizó el estudio de estabilidad acelerada de tabletas de levodopa-carbidopa (250-25 mg con el empleo de un método de cromatografía líquida de alta resolución y se comprobó su especificidad para estos fines. Se analizó la influencia de medios degradantes artificiales sobre los productos activos, además del efecto de la humedad sobre la estabilidad del producto, colocándolo en hidrostatos con humedades controladas. Este medicamento, producción nacional, cumplió con las especificaciones de calidad descritas en la USP 23 y mostró una alta estabilidad térmica.An accelerated stability study of levodopa-carbidopa tablets (250-25 mg was made using high-performance liquid chromatography which specificity for these purposes was proved. The influence of the artificial degrading media on the active products was analyzed and also the effect of humidity on the product´s satbility was examined after placing the tablets into hydrostats under controlled humidity levels. This domestically-made drug met the quality standards described in USP 23 and showed high heat stability.

30 CFR 250.113 - What procedures must I follow when welding?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What procedures must I follow when welding? 250....113 What procedures must I follow when welding? (a) Before you weld, you must move any equipment containing hydrocarbons or other flammable substances at least 35 feet horizontally from the welding area...

Search for charm in 250 GeV/c π-p interactions

International Nuclear Information System (INIS)

Harris, R.; Bogert, D.; Hanft, R.

1975-01-01

Inclusive cross sections are found for strange particle production in π - p interactions at 250 GeV/c in a search for charmed particles using neutral particle decays in a bubble chamber. The results are preliminary, but at the present statistical level no evidence was found for charmed particle production

12 CFR 250.180 - Reports of changes in control of management.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Reports of changes in control of management... FEDERAL RESERVE SYSTEM MISCELLANEOUS INTERPRETATIONS Interpretations § 250.180 Reports of changes in control of management. (a) Under a statute enacted September 12, 1964 (Pub. L. 88-593; 78 Stat. 940) all...

Low-level determination of transuranic elements in marine environment samples

International Nuclear Information System (INIS)

Ballestra, S.; Holm, E.; Fukai, R.

1978-01-01

The procedures developed and currently employed in the Monaco Laboratory for determining transuranic elements in seawater, marine sediments and organisms are described and discussed. While the standard anion-exchange procedure from the hydrochloric acid medium is used for the separation of plutonium isotopes from americium, purification of americium and curium is achieved by an ion-exchange sorption from the methanol-nitric acid medium, followed by an elution with the methanol-hydrochloric acid mixture. Satisfactory clean-up of plutonium as well as americium and curium can be achieved by applying the described procedures. (author)

30 CFR 250.248 - What solid and liquid wastes and discharges information and cooling water intake information must...

Science.gov (United States)

2010-07-01

... following solid and liquid wastes and discharges information and cooling water intake information must... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What solid and liquid wastes and discharges information and cooling water intake information must accompany the DPP or DOCD? 250.248 Section 250.248...

250 Years of the State Survey

Directory of Open Access Journals (Sweden)

Ivana Wechselberger

2014-06-01

Full Text Available The first topographic survey of the Habsburg Monarchy was decreed by Maria Theresa 250 years ago, on May 13, 1764. A conference was held on the occasion of the anniversary by the Austrian State Geodetic Administration (BEV – Bundesamt für Eich- und Vermessungswesen and the Institute for Military Geosciences (IMG – Institut für Militärisches Geowesen in Vienna on May 13 and 14, 2014. The conference was sort of a time travel through Austrian state surveys. Historical development and methods of the first three state surveys (18th and 19th century were presented on the first conference day. Lectures were held by representatives of Austrian scientific institutions and new countries of the Monarchy. The second conference day was dedicated to the 4th state survey (20th century and its impact on civilian and military application and economy.

c-Jun binds the N terminus of human TAF(II)250 to derepress RNA polymerase II transcription in vitro.

Science.gov (United States)

Lively, T N; Ferguson, H A; Galasinski, S K; Seto, A G; Goodrich, J A

2001-07-06

c-Jun is an oncoprotein that activates transcription of many genes involved in cell growth and proliferation. We studied the mechanism of transcriptional activation by human c-Jun in a human RNA polymerase II transcription system composed of highly purified recombinant and native transcription factors. Transcriptional activation by c-Jun depends on the TATA-binding protein (TBP)-associated factor (TAF) subunits of transcription factor IID (TFIID). Protein-protein interaction assays revealed that c-Jun binds with high specificity to the largest subunit of human TFIID, TAF(II)250. The region of TAF(II)250 bound by c-Jun lies in the N-terminal 163 amino acids. This same region of TAF(II)250 binds to TBP and represses its interaction with TATA boxes, thereby decreasing DNA binding by TFIID. We hypothesized that c-Jun is capable of derepressing the effect of the TAF(II)250 N terminus on TFIID-driven transcription. In support of this hypothesis, we found that c-Jun increased levels of TFIID-driven transcription in vitro when added at high concentrations to a DNA template lacking activator protein 1 (AP-1) sites. Moreover, c-Jun blocked the repression of TBP DNA binding caused by the N terminus of TAF(II)250. In addition to revealing a mechanism by which c-Jun activates transcription, our studies provide the first evidence that an activator can bind directly to the N terminus of TAF(II)250 to derepress RNA polymerase II transcription in vitro.

Tularosa, NM 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

Basic research using the 250 kW research reactor of the Jozef Stefan Institute

International Nuclear Information System (INIS)

Dimic, V.

1984-01-01

The 250 kW TRIGA Mark II reactor is a light water reactor with solid fuel elements in which the zirconium hydride moderator is homogeneously distributed between enriched uranium. The reactor therefore has a large prompt negative temperature coefficient of reactivity; the fuel also has a very high retention of radioactive fission products. The experimental facilities include a rotary specimen rack, a central in-core radiation thimble, a pneumatic transfer system and pulsing capability. Other experimental facilities include two radial and two tangential beam tubes, a graphite thermal column and a graphite thermalizing column. At the steady state power of 250 kW the peak flux is 1x10 13 n/cm 2 in the central test position. In addition, pulsing to about 2000 MW is usually provided giving peak fluxes of about 2x10 16 n/cm 2 sec. All TRIGA reactors produce a core-average thermal neutron flux of about 10 7 n.v. per watt. Only with very large accelerators can such high fluxes be achieved. The types of research could be summarized as follows: thermal neutron scattering, neutron radiography, neutron and nuclear physics, activation analysis, radiochemistry, biology and medicine, and teaching and training. Typical applied research with a 250 kW reactor has been conducted in medicine, in biology, archaeology, metallurgy and materials science, engineering and criminology. It is well known that research reactors have been used routinely to produce isotopes for industry and medicine. We can conclude that the 250 kW TRIGA reactor is a useful and wide ranging source of radiation for basic and applied research. The operation cost for this instrument is relatively low. (author)

SPECT scintigraphy with HDP and Mab BW 250/183 of loosened hip endoprothesis

Energy Technology Data Exchange (ETDEWEB)

Predic, P [Hospital Celje, Celje (Sierra Leone); Gregoric, E [Hospital Izola, Izola (Sierra Leone); Dodig, D [Clinical Hospital Centre, Zagreb (Croatia). Dept. of Nuclear Medicine and Radiation Protection

1994-10-01

Main problem of the loosened hip endoprothesis is in distinguishing between the aseptic and septic loosening of endoprothesis. The study involved 27 pts with a loosened hip; 15 pts with aseptic and 12 pts with septic loosening. The patients were injected 550-770 MBq Tc-99m-HDP and underwent SPECT scintigraphy of the hips to repeat then the examination with only 370 MBq Tc-99m-Mab Bw 230/183. HDP application evidenced positive accumulation at the endoprothesis in all patients with a loosened hip while Mab Bw 250/183 only in the patients with septic loosening. Conclusion: SPECT scintigraphy of hip endoprothesis with HDP and Mab BW 250/183 allows differential diagnosing between septic and aseptic hip loosening and hereby a correct therapeutical approach. (author).

30 CFR 250.111 - Who oversees operations under my welding plan?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Who oversees operations under my welding plan... § 250.111 Who oversees operations under my welding plan? A welding supervisor or a designated person in charge must be thoroughly familiar with your welding plan. This person must ensure that each welder is...

30 CFR 250.407 - What tests must I conduct to determine reservoir characteristics?

Science.gov (United States)

2010-07-01

... Gas Drilling Operations General Requirements § 250.407 What tests must I conduct to determine... of oil, gas, sulphur, and water in the formations penetrated by logging, formation sampling, or well...

Does the Loss of ARID1A (BAF-250a Expression in Endometrial Clear Cell Carcinomas Have Any Clinicopathologic Significance? A Pilot Assessment

Directory of Open Access Journals (Sweden)

Oluwole Fadare, Idris L. Renshaw, Sharon X. Liang

2012-01-01

Full Text Available SWI/SNF chromatin-modification complexes use the energy of ATP hydrolysis to remodel nucleosomes and to affect transcription and several cellular processes. Accordingly, their loss of function has been associated with malignant transformation. ARID1A (the expression of whose product, BAF250a, a key complex component, is lost when mutated has recently been identified as a tumor suppressor gene that is mutated in 46-57% of ovarian clear cell carcinoma (CCC. The purposes of this study are to assess the frequency of loss of BAF250a expression in endometrial CCC and whether this loss has any discernable clinicopathologic implications. 34 endometrial carcinomas with a CCC component (including 22 pure CCC, 8 mixed carcinomas with a 10% CCC component, and 4 carcinosarcomas with a CCC epithelial component, were evaluated by immunohistochemistry using a monoclonal antibody directed against the human BAF250a protein. 5 (22.7% of the 22 pure CCC were entirely BAF250a negative, whereas the remainder showed diffuse immunoreactivity. None of 4 carcinosarcomas and only 1 (12.5% of the 8 mixed carcinomas were BAF250a negative. There was no discernable relationship between BAF250a immunoreactivity status and tumor architectural patterns (solid, papillary or tubulocystic areas or cell type (flat, hobnail or polygonal. Of the 22 patients with pure CCC, 14, 2, 3, and 3 were International Federation of Gynecology and Obstetrics stages 1, II, III and IV respectively. Interestingly, all 5 BAF250a negative cases were late stage [stages III or IV] as compared with 1 of 17 BAF250a positive cases (p=0.0002. Thus, 83% (5/6 of all late stage cases were BAF250a [-], as compared with 0 (0% of the 16 early stage (I or II cases (p=.0002. BAF250a negative and positive cases did not show any statistically significant difference regarding patient age and frequency of lymphovascular invasion or myometrial invasion. As may be anticipated from the concentration of late stage cases in

In situ stress measurements at 250m gallery off the ventilation shaft

International Nuclear Information System (INIS)

Nakamura, Takahiro; Sanada, Hiroyuki; Sugita, Yutaka; Kato, Harumi

2011-06-01

From FY2000 to FY2005, JAEA had been making research at ground surface of Horonobe town for repository of high-level radioactive waste. During this period, geological investigation, hydrogeology investigation, rock mechanics investigation, geochemical investigation using boreholes were carried out in Hokushin area which is about 3kmx3km in surface area of Horonobe town in order to construct a geological environment model and to confirm the methodology for safety assessment. Now the research program proceeds to the next stage where the underground drifts and shafts are under construction. In the underground rock mass, in situ stress is the sum of tectonic stress as well as overlying stress due to gravity. In situ stresses enter into excavation design and are required in order to predict the response of rock masses to the disturbance associated with those structures. For these reasons, JAEA has carried out in situ stress measurements using vertical boreholes drilled from ground surface to evaluate the state of horizontal stress in the area. In the research during the underground construction, comparison between the stress measurements carried out at surface and at underground is conducted. And if inconsistency between these two measurements is found, the state of stress will be updated based on more reliable information. In order to study the 3D in situ state of stress around Horonobe Underground Research Laboratory, hydraulic fracturing tests and stress relief method (Conical-ended borehole method) were conducted at the 250m gallery located near the bottom of the ventilation shaft. Three 20.0m long boreholes, 09-V250-M01(slightly upwards), 09-V250-M02(slightly upwards) and 09-V250-M03(vertical), were drilled from the gallery using 76mm diameter bit. The results of the measurements are summarized as follows: (1) Hydraulic fracturing technique. Hydraulic fracturing technique using the test equipment with sufficiently small compliance was carried out in the three

Acoustic emission during tensile deformation of M250 grade maraging steel

Science.gov (United States)

Mukhopadhyay, Chandan Kumar; Rajkumar, Kesavan Vadivelu; Chandra Rao, Bhaghi Purna; Jayakumar, Tamanna

2012-05-01

Acoustic emission (AE) generated during room temperature tensile deformation of varyingly heat treated (solution annealed and thermally aged) M250 grade maraging steel specimens have been studied. Deformation of microstructure corresponding to different heat treated conditions in this steel could be distinctly characterized using the AE parameters such as RMS voltage, counts and peak amplitude of AE hits (events).

Effects of actinide burning on waste disposal at Yucca Mountain

International Nuclear Information System (INIS)

Hirschfelder, J.

1992-01-01

Release rates of 15 radionuclides from waste packages expected to result from partitioning and transmutation of Light-Water Reactor (LWR) and Actinide-Burning Liquid-Metal Reactor (ALMR) spent fuel are calculated and compared to release rates from standard LWR spent fuel packages. The release rates are input to a model for radionuclide transport from the proposed geologic repository at Yucca Mountain to the water table. Discharge rates at the water table are calculated and used in a model for transport to the accessible environment, defined to be five kilometers from the repository edge. Concentrations and dose rates at the accessible environment from spent fuel and wastes from reprocessing, with partitioning and transmutation, are calculated. Partitioning and transmutation of LWR and ALMR spent fuel reduces the inventories of uranium, neptunium, plutonium, americium and curium in the high-level waste by factors of 40 to 500. However, because release rates of all of the actinides except curium are limited by solubility and are independent of package inventory, they are not reduced correspondingly. Only for curium is the repository release rate much lower for reprocessing wastes

Peculiarities of extraction of carbonate complexes of trivalent transplutonium elements by alkylpyrocatechins

International Nuclear Information System (INIS)

Karalova, Z.K.; Bukina, T.I.; Myasoedov, B.F.; Fedorov, L.A.; Sokolovskij, S.A.

1987-01-01

Extraction of trivalent americium, curium, californium and europium by technical mixture of mono- and didecylpyrocatechin (TAP) in various diluents from carbonate solutions is investigated. Effect of many factors (pH, K 2 CO 3 concentration, TAP, metal; the time of phase contact) on the completeness of element isolation and separation is clarified. It is ascertained that the elements listed are quantitatively extracted by TAP solution in toluene and cyclohexane in the range of K 2 CO 3 concentrations from 0.25 to 1.5 mol/l. The difference in americium and curium distribution coefficient during their extraction by TAP from 0.25 mol/l of K 2 CO 3 solution is detected. Separation coefficients of the pair increase with the increase of carbonate solution pH. The separation can be improved at the stage of element reextraction by the mixture of K 2 CO 3 and DTPA or EDTA from alkylpyrocatechin, sunce rate constants of americium and curium reextraction differ greatly. Using 13 C NMR the composition of compounds in organic phase on the basis of 4-(α, α-dioctylethyl)pyrocatechin is investigated

Proliferation resistance of the lithium reduction process

International Nuclear Information System (INIS)

Ko, W. I.; Ha, J. H.; Lee, S. Y.; Song, D. Y.; Kim, H. D.; Park, S. W.

2002-01-01

This paper addresses the characteristics of proliferation resistance of the lithium reduction process and international domestic safeguarding methods. In addition to dealing with qualitative features of the proliferation resistance, this study is emphasizing on the quantitative analysis of radiation barrier, which could be a significant accessibility barrier if the field is high enough to force a theft to shield the object during a theft. From the radiation barrier analysis, it is indicated that whole-body radiation dose is about 20 rem/hr at one meter of smelt and ingot metal of 40 kgHM, which could be considered to be a significant reduction in risk of theft. For safeguarding of this process, we propose a NDA concept for nuclear material accounting which is to measure the amount of curium in the reduction metal and associated process samples using a neutron coincidence counter and then to convert the curium mass into special nuclear material with predetermined curium ratios. For this, a well-type neutron coincidence counter with substantial shielding to protect the system from high gamma radiation is conceptually designed

Compact 250-kV injector system for PIGMI

International Nuclear Information System (INIS)

Hamm, R.W.; Stevens, R.R. Jr.; Mueller, D.W.; Lederer, H.M.

1978-01-01

A 250-kV proton injector to be used in the development of a linac suitable for medical applications has been constructed. This injector utilizes a spherical Pierce geometry to produce a converging beam. A gas insulated accelerating column is cantilevered on a grounded vacuum system, with a separate high voltage equipment dome connected to a 300-kV Cockcroft-Walton power supply. The injector can be operated locally or remotely, with the remote control accomplished by a microprocessor system linked to a central control minicomputer. This injector has been designed as a low-cost compact system. The design details and the data obtained during initial operation are presented

30 CFR 250.192 - What reports and statistics must I submit relating to a hurricane, earthquake, or other natural...

Science.gov (United States)

2010-07-01

... relating to a hurricane, earthquake, or other natural occurrence? 250.192 Section 250.192 Mineral Resources... statistics must I submit relating to a hurricane, earthquake, or other natural occurrence? (a) You must... tropical storm, or an earthquake. Statistics include facilities and rigs evacuated and the amount of...

An evaluation of the Meditech M250 and a comparison with other CT scanners

International Nuclear Information System (INIS)

Greensmith, R.; Richardson, R.B.; Mackintosh, I.P.; Sargood, A.J.; Stevens, P.H.

1985-01-01

The Meditech M250 computerised tomography (CT) machine was evaluated during the first half of 1984. Measurements were made of noise, modulation transfer function, slice width, radiation dose profile, uniformity and linearity of CT number, effective photon energy and parameters relating to machine specification, such as pixel size and scan time. All breakdowns were logged to indicate machine reliability. A comparison with the established EMI CT1010 and CT5005 was made for noise, resolution and multislice radiation dose, as well as the dose efficiency or quality (Q) factor for both head and body modes of operation. The M250 was found to perform to its intended specification with an acceptable level of reliability. (author)

An evaluation of the Meditech M250 and a comparison with other CT scanners.

Science.gov (United States)

Greensmith, R; Richardson, R B; Sargood, A J; Stevens, P H; Mackintosh, I P

1985-11-01

The Meditech M250 computerised tomography (CT) machine was evaluated during the first half of 1984. Measurements were made of noise, modulation transfer function, slice width, radiation dose profile, uniformity and linearity of CT number, effective photon energy and parameters relating to machine specification, such as pixel size and scan time. All breakdowns were logged to indicate machine reliability. A comparison with the established EMI CT1010 and CT5005 was made for noise, resolution and multislice radiation dose, as well as the dose efficiency or quality (Q) factor for both head and body modes of operation. The M250 was found to perform to its intended specification with an acceptable level of reliability.

21 CFR 250.101 - Amphetamine and methamphetamine inhalers regarded as prescription drugs.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Amphetamine and methamphetamine inhalers regarded... DRUGS New Drug or Prescription Status of Specific Drugs § 250.101 Amphetamine and methamphetamine inhalers regarded as prescription drugs. (a) Recurring reports of abuse and misuse of methamphetamine (also...

30 CFR 250.806 - Safety and pollution prevention equipment quality assurance requirements.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Safety and pollution prevention equipment... Gas Production Safety Systems § 250.806 Safety and pollution prevention equipment quality assurance... install only certified safety and pollution prevention equipment (SPPE) in wells located on the OCS. SPPE...

41 CFR Appendix C to Part 60 - 250-Review of Personnel Processes

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true 250-Review of Personnel Processes C Appendix C to Part 60 Public Contracts and Property Management Other Provisions Relating to Public Contracts OFFICE OF FEDERAL CONTRACT COMPLIANCE PROGRAMS, EQUAL EMPLOYMENT OPPORTUNITY, DEPARTMENT...

Production of $D^{\\pm}$ Mesons in $K^+$ Nucleon Collisions at 250 GeV

Energy Technology Data Exchange (ETDEWEB)

da Motta Filho, Helio [Rio de Janeiro, CBPF

1993-11-01

The $X_f$, $P^2_t$ and $p_t$ distribution of $D^{\\pm}$ mesons produced by 250 GeV $K^+$-nucleon interactions are measured through the decay channel $D^{\\pm} \\to K^{\\mp}\\pi^{\\pm} \\pi^{\\pm}$....

MODIS/Aqua Calibrated Radiances 5-Min L1B Swath 250m - NRT

Data.gov (United States)

National Aeronautics and Space Administration — The 250 meter MODIS Level 1B Near Real Time (NRT) data set contains calibrated and geolocated at-aperture radiances for 2 discrete bands located in the 0.62 to 0.88...

250 kV 6 mA compact Cockcroft-Walton high-voltage power supply

Energy Technology Data Exchange (ETDEWEB)

Ma, Zhan-Wen; Su, Xiao-Dong; Wei, Zhen; Huang, Zhi-Wu; Miao, Tian-You; Su, Tong-Ling [School of Nuclear Science and Technology, Lanzhou University, Lanzhou 730000 (China); Lu, Xiao-Long; Wang, Jun-Run; Yao, Ze-En, E-mail: zeyao@lzu.edu.cn [School of Nuclear Science and Technology, Lanzhou University, Lanzhou 730000 (China); Engineering Research Center for Neutron Application, Ministry of Education, Lanzhou University, Lanzhou 730000 (China)

2016-08-15

A compact power supply system for a compact neutron generator has been developed. A 4-stage symmetrical Cockcroft-Walton circuit is adopted to produce 250 kV direct current high-voltage. A 2-stage 280 kV isolation transformer system is used to drive the ion source power supply. For a compact structure, safety, and reliability during the operation, the Cockcroft-Walton circuit and the isolation transformer system are enclosed in an epoxy vessel containing the transformer oil whose size is about ∅350 mm × 766 mm. Test results indicate that the maximum output voltage of the power supply is 282 kV, and the stability of the output voltage is better than 0.63% when the high voltage power supply is operated at 250 kV, 6.9 mA with the input voltage varying ±10%.

Identification of colloids in nuclear waste glass reactions

International Nuclear Information System (INIS)

Cunnane, J.C.; Bates, J.K.

1991-01-01

Characterization data for particulates formed under a variety of laboratory leaching conditions that simulate glass reaction in a repository environment are presented. Data on the particle size distributions and filterable fractions for neptunium, plutonium, americium, and curium were obtained by filtrations through a series of filters with pore sizes ranging from 1 μm to 3.8 nm. The neptunium was found to be largely nonfilterable. Americium and plutonium were associated with filterable particles. The particles with which the americium, plutonium, and curium were associated were characterized using transmission electron microscopy (TEM) examination techniques. 8 refs., 1 fig., 2 tabs

Clinical application study of bone marrow immunoscintigraphy using 99mTc-labelled anti-granulocyte monoclonal antibody BW250/183

International Nuclear Information System (INIS)

Liu Zengli; Wu Jinchang; Shi Yizhen; Tang Jun

2001-01-01

Objective: To study: (1) The labelling method of 99m Tc-BW250/183 and its organ distribution pattern after injection. (2) The clinical value of bone marrow immunoscintigraphy of evaluation of patients with aplastic anemia. (3) The clinical value of bone marrow immunoscintigraphy of determination of bone metastasis. Methods: (1) Whole body imaging was performed to one volunteer after injection of 555 MBq 99m Tc-BW250/183, meanwhile, 2 ml blood samples was taken from a cubital vein. The percentage of radioactivity of different organs and the kinetic data of in-vivo 99m Tc-BW250/183 was then calculated. In all the blood samples the peripheral leukocytes were counted by a standard procedure. (2) Bone marrow immunoscintigraphy were performed to 8 patients with aplastic anemia 4 h after injection of 99m Tc-BW250/183, 6 of them also underwent bone marrow imaging with 99m Tc-SC. (3) Bone marrow immunoscintigraphy and conventional bone scan were performed to 14 patients with suspected bone metastases to detect bone metastases. The results was compared with X-ray, X-CT or MRI. Results: 99m Tc-BW250/183 is a safe and ideal bone marrow imaging agent. Bone marrow immunoscintigraphy plays an important role in evaluating patients with aplastic anemia and determining bone metastases

ERP C250 shows the elderly (cognitively normal, Alzheimer's disease) store more stimuli in short-term memory than Young Adults do.

Science.gov (United States)

Chapman, Robert M; Gardner, Margaret N; Mapstone, Mark; Klorman, Rafael; Porsteinsson, Anton P; Dupree, Haley M; Antonsdottir, Inga M; Kamalyan, Lily

2016-06-01

To determine how aging and dementia affect the brain's initial storing of task-relevant and irrelevant information in short-term memory. We used brain Event-Related Potentials (ERPs) to measure short-term memory storage (ERP component C250) in 36 Young Adults, 36 Normal Elderly, and 36 early-stage AD subjects. Participants performed the Number-Letter task, a cognitive paradigm requiring memory storage of a first relevant stimulus to compare it with a second stimulus. In Young Adults, C250 was more positive for the first task-relevant stimulus compared to all other stimuli. C250 in Normal Elderly and AD subjects was roughly the same to relevant and irrelevant stimuli in Intratrial Parts 1-3 but not 4. The AD group had lower C250 to relevant stimuli in part 1. Both normal aging and dementia cause less differentiation of relevant from irrelevant information in initial storage. There was a large aging effect involving differences in the pattern of C250 responses of the Young Adult versus the Normal Elderly/AD groups. Also, a potential dementia effect was obtained. C250 is a candidate tool for measuring short-term memory performance on a biological level, as well as a potential marker for memory changes due to normal aging and dementia. Copyright © 2016 International Federation of Clinical Neurophysiology. Published by Elsevier Ireland Ltd. All rights reserved.

PENGARUH KELOMPOK REFERENSI TERHADAP KEPUTUSAN PEMBELIAN KAWASAKI NINJA 250 CC

OpenAIRE

Kartika WB, Sylvia; Sidig, Rosyid

2018-01-01

The purpose of this study is to examine the affect of reference groups  on purchasing decision of  Kawasaki Ninja 250 cc in the city of Jambi. Size of sample consist of 100 unit that chousen randomly. While data analysis used  multiple regression analysis. The results showed that simultaneouly   normative, value expression, and  informative have significant role. But, based on partiall test  normative has no significant affect. Hence,  reference group h...

Study of solar features causing GMSs with 250γ H 400γ

Indian Academy of Sciences (India)

The effect of solar features on geospheric conditions leading to geomagnetic storms (GMSs) with planetary index, p ≥ 20 and the range of horizontal component of the Earth's magnetic field such that 250 < < 400 has been investigated using interplanetary magnetic field (IMF), solar wind plasma (SWP) and solar ...

30 CFR 250.290 - What operations require approval of the Conceptual Plan?

Science.gov (United States)

2010-07-01

... INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Deepwater Operations Plans (dwop) § 250.290 What operations require approval of the Conceptual Plan? You may... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What operations require approval of the...

Gallup, NM AZ 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

Santa Fe, NM 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

Concentration of ions Co(II), Ni(II) at the Tokem-250 carboxylic cation exchange for catalysts development

Science.gov (United States)

Zharkova, Valentina; Bobkova, Ludmila; Brichkov, Anton; Kozik, Vladimir

2017-11-01

Sorption and catalytic properties of the cation exchanger are investigated. It was found that the Tokem-250 has a wide operating range of pH. The value of the effective ionization constant of the functional groups of the cation exchanger (pKa) is 6.59. The Tokem-250 cation exchanger exhibits selectivity to Ni2+ ions to Co2+ (D˜103). This is probably due to the stability of ion-exchange complexes detected by the method of diffuse reflectance electron spectroscopy (ESDD). According to these data, for Co2+ ions, in contrast to Ni2+, tetragonal distortion of octahedral coordination is characteristic, which has a positive effect on the stability of complexes with Co2+. To obtain spherical catalysts on the basis of Tokem-250, cobalt-containing samples of cation exchanger were used. The developed spherical materials have catalytic activity in the reactions of deep and partial oxidation of n-heptane.

Use of radioanalytical methods for determination of uranium, neptunium, plutonium, americium and curium isotopes in radioactive wastes; Utilizacao de metodos radioanaliticos para a determinacao de isotopos de uranio, plutonio, americio e curio em rejeitos radioativos

Energy Technology Data Exchange (ETDEWEB)

Geraldo, Bianca

2012-07-01

Activated charcoal is a common type of radioactive waste that contains high concentrations of fission and activation products. The management of this waste includes its characterization aiming the determination and quantification of the specific radionuclides including those known as Difficult-to-Measure Radionuclides (RDM). The analysis of the RDM's generally involves complex radiochemical analysis for purification and separation of the radionuclides, which are expensive and time-consuming. The objective of this work was to define a methodology for sequential analysis of the isotopes of uranium, neptunium, plutonium, americium and curium present in a type of radioactive waste, evaluating chemical yield, analysis of time spent, amount of secondary waste generated and cost. Three methodologies were compared and validated that employ ion exchange (TI + EC), extraction chromatography (EC) and extraction with polymers (ECP). The waste chosen was the activated charcoal from the purification system of primary circuit water cooling the reactor IEA-R1. The charcoal samples were dissolved by acid digestion followed by purification and separation of isotopes with ion exchange resins, extraction and chromatographic extraction polymers. Isotopes were analyzed on an alpha spectrometer, equipped with surface barrier detectors. The chemical yields were satisfactory for the methods TI + EC and EC. ECP method was comparable with those methods only for uranium. Statistical analysis as well the analysis of time spent, amount of secondary waste generated and cost revealed that EC method is the most effective for identifying and quantifying U, Np, Pu, Am and Cm present in charcoal. (author)

12 CFR 250.408 - Short-term negotiable notes of banks not securities under section 32, Banking Act of 1933.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Short-term negotiable notes of banks not securities under section 32, Banking Act of 1933. 250.408 Section 250.408 Banks and Banking FEDERAL RESERVE... securities under section 32, Banking Act of 1933. (a) The Board of Governors has been asked whether short...

30 CFR 250.251 - If I propose activities in the Alaska OCS Region, what planning information must accompany the DPP?

Science.gov (United States)

2010-07-01

... Region, what planning information must accompany the DPP? 250.251 Section 250.251 Mineral Resources... Region, what planning information must accompany the DPP? If you propose development and production activities in the Alaska OCS Region, the following planning information must accompany your DPP: (a...

30 CFR 250.462 - What are the requirements for well-control drills?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are the requirements for well-control... Other Drilling Requirements § 250.462 What are the requirements for well-control drills? You must conduct a weekly well-control drill with each drilling crew. Your drill must familiarize the crew with its...

30 CFR 250.1400 - How does MMS begin the civil penalty process?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How does MMS begin the civil penalty process...) Civil Penalties § 250.1400 How does MMS begin the civil penalty process? This subpart explains MMS's... other minerals operations in the OCS has a violation. Whenever MMS determines, on the basis of available...

Covalently linked multimers of gold nanoclusters Au102(p-MBA)44 and Au∼250(p-MBA)n.

Science.gov (United States)

Lahtinen, Tanja; Hulkko, Eero; Sokołowska, Karolina; Tero, Tiia-Riikka; Saarnio, Ville; Lindgren, Johan; Pettersson, Mika; Häkkinen, Hannu; Lehtovaara, Lauri

2016-11-10

We present the synthesis, separation, and characterization of covalently-bound multimers of para-mercaptobenzoic acid (p-MBA) protected gold nanoclusters. The multimers were synthesized by performing a ligand-exchange reaction of a pre-characterized Au 102 (p-MBA) 44 nanocluster with biphenyl-4,4'-dithiol (BPDT). The reaction products were separated using gel electrophoresis yielding several distinct bands. The bands were analyzed by transmission electron microscopy (TEM) revealing monomer, dimer, and trimer fractions of the nanocluster. TEM analysis of dimers in combination with molecular dynamics simulations suggest that the nanoclusters are covalently bound via a disulfide bridge between BPDT molecules. The linking chemistry is not specific to Au 102 (p-MBA) 44 . The same approach yields multimers also for a larger monodisperse p-MBA-protected cluster of approximately 250 gold atoms, Au ∼250 (p-MBA) n . While the Au 102 (p-MBA) 44 is not plasmonic, the Au ∼250 (p-MBA) n nanocluster supports localized surface plasmon resonance (LSPR) at 530 nm. Multimers of the Au ∼250 (p-MBA) n exhibit additional transitions in their UV-vis spectrum at 630 nm and 810 nm, indicating the presence of hybridized LSPR modes. Well-defined structures and relatively small sizes make these systems excellent candidates for connecting ab initio theoretical studies and experimental quantum plasmonics. Moreover, our work opens new possibilities in the controlled synthesis of advanced monodisperse nanocluster superstructures.

30 CFR 250.220 - If I propose activities in the Alaska OCS Region, what planning information must accompany the EP?

Science.gov (United States)

2010-07-01

... Region, what planning information must accompany the EP? 250.220 Section 250.220 Mineral Resources... activities in the Alaska OCS Region, what planning information must accompany the EP? If you propose exploration activities in the Alaska OCS Region, the following planning information must accompany your EP: (a...

30 CFR 250.404 - What are the requirements for the crown block?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are the requirements for the crown block... General Requirements § 250.404 What are the requirements for the crown block? You must have a crown block safety device that prevents the traveling block from striking the crown block. You must check the device...

Coomassie Brilliant Blue G-250 Dye: An Application for Forensic Fingerprint Analysis.

Science.gov (United States)

Brunelle, Erica; Le, Anh Minh; Huynh, Crystal; Wingfield, Kelly; Halámková, Lenka; Agudelo, Juliana; Halámek, Jan

2017-04-04

The Bradford reagent, comprised of the Coomassie Brilliant Blue G-250 dye, methanol, and phosphoric acid, has been traditionally used for quantifying proteins. Use of this reagent in the Bradford assay relies on the binding of the Coomassie Blue G-250 dye to proteins. However, the ability of the dye to react with a small group of amino acids (arginine, histidine, lysine, phenylalanine, tyrosine, and tryptophan) makes it a viable chemical assay for fingerprint analysis in order to identify the biological sex of the fingerprint originator. It is recognized that the identification of biological sex has been readily accomplished using two other methods; however, both of those systems are reliant upon a large group of amino acids, 23 to be precise. The Bradford assay, described here, was developed specifically to aid in the transition from targeting large groups of amino acids, as demonstrated in the previous studies, to targeting only a single amino acid without compromising the intensity of the response and/or the ability to differentiate between two attributes. In this work, we aim to differentiate between female fingerprints and male fingerprints.

30 CFR 250.1151 - How often must I conduct well production tests?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How often must I conduct well production tests... Requirements Well Tests and Surveys § 250.1151 How often must I conduct well production tests? (a) You must conduct well production tests as shown in the following table: You must conduct: And you must submit to...

30 CFR 250.110 - What must I include in my welding plan?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must I include in my welding plan? 250.110... must I include in my welding plan? You must include all of the following in the Welding Plan that you... qualified personnel weld; (c) Practices and procedures for safe welding that address: (1) Welding in...

Off-resonance transformer charging for 250-kV water Blumlein

International Nuclear Information System (INIS)

Cook, E.; Reginato, L.

1978-01-01

An off-resonance transformer for charging a 250-kV Blumlein system provides a viable alternative to other charging schemes by permitting the use of conventional thyratrons. Such a transformer must have reliability, a reasonable voltage step-up, and a non-reversing primary current. The analysis, design, and performance data for such a transformer are presented. The strong interrelationship between transformer design and Blumlein requirements necessitates that Blumlein description and design criterion be briefly presented prior to transformer design such that transformer load requirements be defined

30 CFR 250.802 - Design, installation, and operation of surface production-safety systems.

Science.gov (United States)

2010-07-01

... Analysis Checklists are included in API RP 14C you must utilize the analysis technique and documentation... device requirements for pipelines are under § 250.1004. (c) Specification for surface safety valves (SSV..., Recommended Practice for Installation, Maintenance, and Repair of Surface Safety Valves and Underwater Safety...

41 CFR 60-250.25 - Health insurance, life insurance and other benefit plans.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Health insurance, life... SEPARATED VETERANS, AND OTHER PROTECTED VETERANS Discrimination Prohibited § 60-250.25 Health insurance, life insurance and other benefit plans. (a) An insurer, hospital, or medical service company, health...

Results of Am isotopic ratio analysis in irradiated MOX fuels

Energy Technology Data Exchange (ETDEWEB)

Koyama, Shin-ichi; Osaka, Masahiko; Mitsugashira, Toshiaki; Konno, Koichi [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center; Kajitani, Mikio

1997-04-01

For analysis of a small quantity of americium, it is necessary to separate from curium which has similar chemical property. As a chemical separation method for americium and curium, the oxidation of americium with pentavalent bismuth and subsequent co-precipitation of trivalent curium with BIP O{sub 4} were applied to analyze americium in irradiated MOX fuels which contained about 30wt% plutonium and 0.9wt% {sup 241}Am before irradiation and were irradiated up to 26.2GWd/t in the experimental fast reactor Joyo. The purpose of this study is to measure isotopic ratio of americium and to evaluate the change of isotopic ratio with irradiation. Following results are obtained in this study. (1) The isotopic ratio of americium ({sup 241}Am, {sup 242m}Am and {sup 243}Am) can be analyzed in the MOX fuels by isolating americium. The isotopic ratio of {sup 242m}Am and {sup 243}Am increases up to 0.62at% and 0.82at% at maximum burnup, respectively, (2) The results of isotopic analysis indicates that the contents of {sup 241}Am decreases, whereas {sup 242m}Am, {sup 243}Am increase linearly with increasing burnup. (author)

Alpha self irradiation effects in nuclear borosilicate glass

International Nuclear Information System (INIS)

Peuget, S.; Roudil, D.; Deschanels, X.; Jegou, C.; Broudic, V.; Bart, J.M.

2004-01-01

The properties of actinide glasses are studied in the context of high-level waste management programs. Reprocessing high burnup fuels in particular will increase the minor actinide content in the glass package, resulting in higher cumulative alpha decay doses in the glass, and raising the question of the glass matrix behavior and especially its containment properties. The effect of alpha self-irradiation on the glass behavior is evaluated by doping the glass with a short-lived actinide ( 244 Cm) to reach in several years the alpha dose received by the future glass packages over several thousand years. 'R7T7' borosilicate glasses were doped with 3 different curium contents (0.04, 0.4 and 1.2 wt% 244 CmO 2 ). The density and mechanical properties of the curium-doped glasses were characterized up to 2. 10 18 α/g, revealing only a slight evolution of the macroscopic behavior of R7T7 glass in this range. The leaching behavior of curium-doped glass was also studied by Soxhlet tests. The results do not show any significant evolution of the initial alteration rate with the alpha dose. (authors)

Routine radiochemical method for the determination of 90Sr, 238Pu, 239+240Pu, 241Am and 244Cm in environmental samples

International Nuclear Information System (INIS)

Ageyev, V.A.; Sajeniouk, A.D.

2005-01-01

Routine analytical procedures have been developed for the reliable simultaneous determination of 90 Sr, 238 Pu, 239+240 Pu, 241 Am and 242-244 Cm, Chernobyl derived radioisotopes and fallout after nuclear weapon tests in a wide range of environmental samples: soil (100-200 g), sediments, aerosols, water and vegetation. This procedure has been applied to thousands of soil and sediment samples and hundreds of biological and water samples taken in the exclusive zone of Chernobyl NPP and different regions of Ukraine from 1989 to the present. After the sample has been properly prepared and isotopic tracers added, plutonium, americium and curium are precipitated with calcium oxalate and then lanthanum fluoride. Plutonium is separated from americium and curium by anion-exchange. Americium and curium are separated from rare earths by cation-exchange with gradient elute α-hydroxy-iso-butyric acid. During projects by AQCS IAEA 'Evaluation of Methods for 90 Sr in a Mineral Matrix' and 'Proficiency Test for 239 Pu, 241 Pu and 241 Am Measurement in a Mineral Matrix' accuracy and precision for 90 Sr, 239 Pu and 241 Am by present procedure was evaluated. Advantages, difficulties and limitations of the method are discussed. (author)

Cooling system upgrading from 250 kW to 1 MW

International Nuclear Information System (INIS)

Anderson, T.V.; Johnson, A.G.; Ringle, J.C.

1972-01-01

The Oregon State TRIGA reactor (OSTR) power capability was upgraded from 250 KW to 1 MW in 1969; however, funds were not available for simultaneous upgrading of the cooling system. Since then, the OSTR has been selectively operating at full power with the original 250 KW cooling system. After funds were made available in 1971 the construction on the new heat exchanger building began. The new cooling system was installed, equipment was checked out, corrections were made, and acceptance tests were run. In addition, several days were required to clean up the primary system water, since increased water flow (350 gpm) swirled 4 year's collection of sediment off the reactor tank bottom and into the primary system. Three interesting items have been noticed, which are apparently a result of the cooling system upgrading: (1) the radiation levels above the reactor tank have been reduced by a factor of 2 to 3, (2) a low resonance vibration in the reactor core occurs at 1 MW. The vibration is attributed to a combination of increased water turbulence and subcooled (surface) nucleate boiling, and (3) direct radiation levels from the demineralizer tank have increased approximately 8-fold. This resulted in a relocation of the tank and the use of supplemental shielding. Increased operating time at higher average power levels, plus disturbance of; sediment on the bottom of the reactor tank are believed to be the main sources of the higher radiation levels

Characterization of aging-induced microstructural changes in M250 maraging steel using magnetic parameters

Energy Technology Data Exchange (ETDEWEB)

Rajkumar, K.V. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Vaidyanathan, S. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Kumar, Anish [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Jayakumar, T. [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)]. E-mail: tjk@igcar.gov.in; Raj, Baldev [Metallurgy and Materials Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Ray, K.K. [Indian Institute of Technology, Kharagpur 721302 (India)

2007-05-15

The best combinations of mechanical properties (yield stress and fracture toughness) of M250 maraging steel is obtained through short-term thermal aging (3-10 h) at 755 K. This is attributed to the microstructure containing precipitation of intermetallic phases in austenite-free low-carbon martensite matrix. Over-aged microstructure, containing reverted austenite degrades the mechanical properties drastically. Hence, it necessitates identification of a suitable non-destructive evaluation (NDE) technique for detecting any reverted austenite unambiguously during aging. The influence of aging on microstructure, room temperature hardness and non-destructive magnetic parameters such as coercivity (H {sub c}), saturation magnetization (M {sub s}) and magnetic Barkhausen emission (MBE) RMS peak voltage is studied in order to derive correlations between these parameters in aged M250 maraging steel. Hardness was found to increase with precipitation of intermetallics during initial aging and decrease at longer durations due to austenite reversion. Among the different magnetic parameters studied, MBE RMS peak voltage was found to be very sensitive to austenite reversion (non-magnetic phase) as they decreased drastically up on initiation of austenite reversion. Hence, this parameter can be effectively utilized to detect and quantify the reverted austenite in maraging steel specimen. The present study clearly indicates that the combination of MBE RMS peak voltage and hardness can be used for unambiguous characterization of microstructural features of technological and practical importance (3-10 h of aging duration at 755 K) in M250 grade maraging steel.

Characterization of aging-induced microstructural changes in M250 maraging steel using magnetic parameters

International Nuclear Information System (INIS)

Rajkumar, K.V.; Vaidyanathan, S.; Kumar, Anish; Jayakumar, T.; Raj, Baldev; Ray, K.K.

2007-01-01

The best combinations of mechanical properties (yield stress and fracture toughness) of M250 maraging steel is obtained through short-term thermal aging (3-10 h) at 755 K. This is attributed to the microstructure containing precipitation of intermetallic phases in austenite-free low-carbon martensite matrix. Over-aged microstructure, containing reverted austenite degrades the mechanical properties drastically. Hence, it necessitates identification of a suitable non-destructive evaluation (NDE) technique for detecting any reverted austenite unambiguously during aging. The influence of aging on microstructure, room temperature hardness and non-destructive magnetic parameters such as coercivity (H c ), saturation magnetization (M s ) and magnetic Barkhausen emission (MBE) RMS peak voltage is studied in order to derive correlations between these parameters in aged M250 maraging steel. Hardness was found to increase with precipitation of intermetallics during initial aging and decrease at longer durations due to austenite reversion. Among the different magnetic parameters studied, MBE RMS peak voltage was found to be very sensitive to austenite reversion (non-magnetic phase) as they decreased drastically up on initiation of austenite reversion. Hence, this parameter can be effectively utilized to detect and quantify the reverted austenite in maraging steel specimen. The present study clearly indicates that the combination of MBE RMS peak voltage and hardness can be used for unambiguous characterization of microstructural features of technological and practical importance (3-10 h of aging duration at 755 K) in M250 grade maraging steel

Characterization of aging-induced microstructural changes in M250 maraging steel using magnetic parameters

Science.gov (United States)

Rajkumar, K. V.; Vaidyanathan, S.; Kumar, Anish; Jayakumar, T.; Raj, Baldev; Ray, K. K.

2007-05-01

The best combinations of mechanical properties (yield stress and fracture toughness) of M250 maraging steel is obtained through short-term thermal aging (3-10 h) at 755 K. This is attributed to the microstructure containing precipitation of intermetallic phases in austenite-free low-carbon martensite matrix. Over-aged microstructure, containing reverted austenite degrades the mechanical properties drastically. Hence, it necessitates identification of a suitable non-destructive evaluation (NDE) technique for detecting any reverted austenite unambiguously during aging. The influence of aging on microstructure, room temperature hardness and non-destructive magnetic parameters such as coercivity ( Hc), saturation magnetization ( Ms) and magnetic Barkhausen emission (MBE) RMS peak voltage is studied in order to derive correlations between these parameters in aged M250 maraging steel. Hardness was found to increase with precipitation of intermetallics during initial aging and decrease at longer durations due to austenite reversion. Among the different magnetic parameters studied, MBE RMS peak voltage was found to be very sensitive to austenite reversion (non-magnetic phase) as they decreased drastically up on initiation of austenite reversion. Hence, this parameter can be effectively utilized to detect and quantify the reverted austenite in maraging steel specimen. The present study clearly indicates that the combination of MBE RMS peak voltage and hardness can be used for unambiguous characterization of microstructural features of technological and practical importance (3-10 h of aging duration at 755 K) in M250 grade maraging steel.

MODIS/Terra Calibrated Radiances 5-Min L1B Swath 250m V005

Data.gov (United States)

National Aeronautics and Space Administration — The 250 meter MODIS Level 1B data set contains calibrated and geolocated at-aperture radiances for 2 discrete bands located in the 0.62 to 0.88 micron region of the...

Study of the stability of the ground states and K-isomeric states of 250Fm and 254102 against spontaneous fission

International Nuclear Information System (INIS)

Lazarev, Yu.A.; Lobanov, Yu.V.; Sagajdak, R.N.; Utenkov, V.K.; Kharitonov, Yu.P.; Shirokovskij, I.V.; Tret'yakova, S.P.; Oganessyan, Yu.Ts.

1988-01-01

By employing the 249 Cf( 4 He, 3n) and 208 Pb( 48 Ca,2n) reactions, experiments to study the stability against spontaneous fission of the nuclides 250 Fm and 254 102 as well as of the two-quasi-particle (2 q-p) K isomers 250 Fm (T 1/2 =1,8±0,1 s) and 254 102 (T 1/2 =0,28±0,04 s) have been performed. The groundstate spontaneous fission of the two nuclides has been discovered and the corresponding branching ratios b sf and partial half-lives T sf , respectively, have been determined to be: (6,9±1,0)x10 -5 , 0,83±0,15 yr for 250 Fm; (1,7±0,5)x10 -3 , (3,2±0,9)x10 4 s for 254 102. As a by-product of these studies, new data about cross sections of the 206,208 Pb( 48 Ca,xn) reactions have been obtained. Experiments designed to search for the spontaneous fission of the 2 q-p K-isometric states in 250 Fm and 254 102 have not revealed the effect in question. The lower limits of the ratios of the partial spontaneous fission half-lives for the 2 q-p K-isomeric states to those for the respective ground states, T * sf /T sf , have been established to be≥10 -1 for 250m Fm/ 250 Fm and ≥5x10 -3 for 254m 102/ 254 102. This means that the stability of the 2 q-p K-isomeric states in 250 Fm and 254 102 against spontaneous fission is practically not inferior to that of the ground states of these nuclei. In accord with the experimental findings, the theoretical estimates of T * sf /T sf made in the present paper show that, due to the influence of the specialization and blocking effects on the potential energy and the effective mass associated with fission, spontaneous fission from 2 q-p K-isomeric states cannot be facilitated but, on the contrary, should be essentially hindered compared with ground-state spontaneous fission

El Paso, TX NM 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

Las Cruces, NM TX 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

Saint Johns, AZ NM 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

Silver City, NM AZ 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

27 CFR 24.250 - Application for use of new treating material or process.

Science.gov (United States)

2010-04-01

... of tests of the shelf life of the treated wine; (6) A tabulation of pertinent information derived... TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Storage, Treatment and Finishing of Wine § 24.250 Application for use of new treating material or process. (a) General. If the proprietor...

30 CFR 250.522 - When do I have to repeat casing diagnostic testing?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When do I have to repeat casing diagnostic... Operations Casing Pressure Management § 250.522 When do I have to repeat casing diagnostic testing? Casing diagnostic testing must be repeated according to the following table: When * * * you must repeat diagnostic...

LCD OF AIR INTAKE MANIFOLDS PHASE 2: FORD F250 AIR INTAKE MANIFOLD

Science.gov (United States)

The life cycle design methodology was applied to the design analysis of three alternatives for the lower plehum of the air intake manifold for us with a 5.4L F-250 truck engine: a sand cast aluminum, a lost core molded nylon composite, and a vibration welded nylon composite. The ...

Magnetic susceptibility of curium pnictides

International Nuclear Information System (INIS)

Nave, S.E.; Huray, P.G.; Peterson, J.R.; Damien, D.A.; Haire, R.G.

1981-09-01

The magnetic susceptibility of microgram quantities of 248 CmP and 248 CmSb has been determined with the use of a SQUID micromagnetic susceptometer over the temperature range 4.2 to 340 K and in the applied magnetic field range of 0.45 to 1600 G. The fcc (NaCl-type) samples yield magnetic transitions at 73K and 162 K for the phosphide and antimonide, respectively. Together with published magnetic data for CmN and CmAs, these results indicate spatially extended exchange interactions between the relatively localized 5f electrons of the metallic actinide atoms

30 CFR 250.272 - If a State objects to the DPP's or DOCD's coastal zone consistency certification, what can I do?

Science.gov (United States)

2010-07-01

... coastal zone consistency certification, what can I do? 250.272 Section 250.272 Mineral Resources MINERALS... objects to the DPP's or DOCD's coastal zone consistency certification, what can I do? If an affected State objects to the coastal zone consistency certification accompanying your proposed or disapproved DPP or...

High reflectance Cr/C multilayer at 250 eV for soft X-ray polarimetry

Energy Technology Data Exchange (ETDEWEB)

Wen, Mingwu; Jiang, Li; Zhang, Zhong; Huang, Qiushi [MOE Key Laboratory of Advanced Micro-Structured Materials, Institute of Precision Optical Engineering (IPOE), School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); Wang, Zhanshan, E-mail: wangzs@tongji.edu.cn [MOE Key Laboratory of Advanced Micro-Structured Materials, Institute of Precision Optical Engineering (IPOE), School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); She, Rui; Feng, Hua [Department of Engineering Physics, Tsinghua University, Beijing (China); Wang, Hongchang [Diamond Light Source, Harwell Science and Innovation Campus, Didcot, Oxfordshire OX11 0DE (United Kingdom)

2015-10-01

X-ray reflection near 45° via multilayer mirrors can be used for astronomical polarization measurements. A Cr/C multilayer mirror (designed for X-ray polarimetry at 250 eV), with a period thickness of 3.86 nm and a bi-layer number of 100, was fabricated using direct current magnetron sputtering. Grazing incidence X-ray reflectometry at 8 keV and transmission electron microscopy were used to investigate the multilayer structure. Different models were introduced to fit the hard X-ray reflectivity curve, which indicates that the layer thickness of two materials slightly drifts from the bottom to the top of the stack. Both the chromium and carbon layers are amorphous with asymmetric interfaces, while the Cr-on-C interface is slightly wider. Based on the good quality of the multilayer structure, a high reflectivity of 21.8% for the s-polarized light was obtained at 250 eV at a grazing incidence angle of 40.7°. The fabricated Cr/C multilayer mirror exhibits high reflectivity and polarization levels in the energy region of 240 eV–260 eV. - Highlights: • We fabricated Cr/C multilayer with 3.8 nm d-spacing. • X-ray reflectometry was used to determine the exact structure of Cr/C multilayer. • A high reflectivity of 21.8% for the s-polarized light was obtained at 250 eV. • Both Cr and C were found to be amorphous with slightly asymmetric interfaces. • A 4-layer model was used to fit and explain the results.

30 CFR 250.243 - What general information must accompany the DPP or DOCD?

Science.gov (United States)

2010-07-01

... characteristics of the produced oil (see definition under 30 CFR 254.6) that you will handle or store at the... definition under § 250.200) you will use to carry out your proposed development and production activities. In... that you expect will have the highest volume of liquid hydrocarbons. Include the estimated flow rate...

30 CFR 250.227 - What environmental impact analysis (EIA) information must accompany the EP?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What environmental impact analysis (EIA... and Information Contents of Exploration Plans (ep) § 250.227 What environmental impact analysis (EIA... requirements. Your EIA must: (1) Assess the potential environmental impacts of your proposed exploration...

Design of diode electron gun for 250 kW CW klystron

International Nuclear Information System (INIS)

Prasad, M.; Pande, S.A.; Hannurkar, P.R.

2005-01-01

A 250 kW CW klystron at frequencies 350 MHz and 700 MHz is being developed at Centre for Advanced Technology. These klystrons are required for forthcoming project like 100 MeV proton Linac for Spallation Neutron Source (SNS) as a main rf sources. In order to develop klystrons, we have designed the diode electron gun, which delivers more than 10 A beam current at 50 kV. This paper describes the simulation results of electron gun with computer code EGUN. (author)

New results on multi-muon production in 250 GeV μ+ Fe interactions

International Nuclear Information System (INIS)

Best, C.H.

1981-05-01

Preliminary results on the contribution to the nucleon structure function F 2 from charm particle production are presented. The data consist of dimuon and trimuon events from a high statistics experiment for a beam energy of 250 GeV. Exotic trimuon events have been observed and are compared to predictions from BETABETA and tautau production and decay. (author)

30 CFR 250.460 - What are the requirements for conducting a well test?

Science.gov (United States)

2010-07-01

... Other Drilling Requirements § 250.460 What are the requirements for conducting a well test? (a) If you intend to conduct a well test, you must include your projected plans for the test with your APD (form MMS...) You must give the District Manager at least 24-hours notice before starting a well test. [68 FR 8423...

77 FR 25720 - Determination That GRIFULVIN V (Griseofulvin Microcrystalline) Tablets, 250 Milligrams, Was Not...

Science.gov (United States)

2012-05-01

... been discontinued from marketing for reasons other than safety or effectiveness. ANDAs that refer to... Sale for Reasons of Safety or Effectiveness AGENCY: Food and Drug Administration, HHS. ACTION: Notice... microcrystalline) tablets, 250 milligrams (mg), was not withdrawn from sale for reasons of safety or effectiveness...

30 CFR 250.136 - How will MMS determine if my operating performance is unacceptable?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How will MMS determine if my operating... Disqualification § 250.136 How will MMS determine if my operating performance is unacceptable? In determining if your operating performance is unacceptable, MMS will consider, individually or collectively: (a...

Managing radioactive wastes of nuclear power plants in operation and site decommissioning phases

International Nuclear Information System (INIS)

Ardalani, E.; Khadivi, S.

2008-01-01

A large nuclear reactor annually produces about 25-50 tons consumed Uranium. These consumed materials consist of Uranium and also Plutonium and Curium. In total, about three percent of these materials are remained from fission. Existing actinides (Uranium, Plutonium, and Curium) cause long-term and short-term radiation that could have harmful effects on the environment. In order to reduce the diverse effects of radioactive wastes in Nuclear Power Plants, different procedures are employed such as compaction, chemical treatment, vitrification, canning and sealing with concrete and safe storage. In this paper, the harmful effects of nuclear wastes on the environment are introduced and a management procedure is presented to minimize its diverse effects

Analysis of the in vitro cleavage products of the tomato black ring virus RNA-1-encoded 250K polyprotein.

OpenAIRE

Demangeat, Gerard; Greif, Charles; Hemmer, O; Fritsch, C

1990-01-01

Tomato black ring virus RNA-1 was translated in a rabbit reticulocyte lysate. The primary translation product of Mr 250K, which corresponds to its whole coding capacity, was synthesized within 45 min and, during further incubation in the translation medium, was proteolytically processed. Essentially, four cleavage products (P190, P120, P60 and P50) were detected and located within P250 by pulse-chase and immunoprecipitation experiments. P190 is an intermediate cleavage product which is furthe...

Transuranium processing plant semiannual report of production, status, and plans for period ending June 30, 1976

Energy Technology Data Exchange (ETDEWEB)

King, L.J.; Bigelow, J.E.; Collins, E.D.

1977-02-01

During the period January 1, 1976, through June 30, 1976, the following amounts of transuranium elements were recovered from ten irradiated HFIR targets: 2 g /sup 243/Am, 50 g /sup 244/Cm, 29 mg /sup 249/Bk, 277 mg /sup 252/Cf, 1.7 mg /sup 253/Es, and 0.5 pg /sup 257/Fm. About 50 mg of high-purity /sup 248/Cm was purified chemically for shipment, and another 75 mg of /sup 248/Cm was separated from /sup 252/Cf. Nineteen HFIR targets, each containing approximately 9 g of curium, were fabricated. There have been no changes during this report period in the chemical processing flowsheets normally used at TRU. Five neutron sources were fabricated, bringing the total fabricated to 84. Six sources that were used previously in various projects have been returned to TRU and are available for reassignment. Special projects included (1) the continued study of /sup 250/Cm production by irradiation of /sup 248/Cm; (2) the production of 0.54 mg of /sup 250/Cf by irradiation of /sup 249/Bk; (3) the separation of approximately 200 pg of /sup 254/Cf from 39-hr /sup 254m/Es that was produced by irradiation of 5 ..mu..g of /sup 253/Es; and (4) the determination of process steps needed to obtain rare-earth fission products in an oxide form from LiCl-based anion exchange raffinate solution.

Shiprock, AZ NM CO UT 1:250,000 Quad USGS Land Use/Land Cover, 1986

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — This dataset contains boundaries for land use and land cover polygons in New Mexico at a scale of 1:250,000. It is in a vector digital data structure. The source...

Remote (250 km Fiber Bragg Grating Multiplexing System

Directory of Open Access Journals (Sweden)

Manuel Lopez-Amo

2011-09-01

Full Text Available We propose and demonstrate two ultra-long range fiber Bragg grating (FBG sensor interrogation systems. In the first approach four FBGs are located 200 km from the monitoring station and a signal to noise ratio of 20 dB is obtained. The second improved version is able to detect the four multiplexed FBGs placed 250 km away, offering a signal to noise ratio of 6–8 dB. Consequently, this last system represents the longest range FBG sensor system reported so far that includes fiber sensor multiplexing capability. Both simple systems are based on a wavelength swept laser to scan the reflection spectra of the FBGs, and they are composed by two identical-lengths optical paths: the first one intended to launch the amplified laser signal by means of Raman amplification and the other one is employed to guide the reflection signal to the reception system.

Flat-topped emission centred at 1 250 nm from quantum dot superluminescent diodes

Directory of Open Access Journals (Sweden)

R.A. Hogg

2010-01-01

Full Text Available We present a method for tailoring a broadband and flat-topped emission spectrum in quantum dot superluminescent diodes based upon modification of the dots-in-compositionally-modulated-well (DCMWELL technique. We demonstrate flat-topped emission with 95 nm full width at half maximum (FWHM, centred at 1 250 nm, and with output power in excess of 8 mW.

Curiously modern DNA for a "250 million-year-old" bacterium.

Science.gov (United States)

Nickle, David C; Learn, Gerald H; Rain, Matthew W; Mullins, James I; Mittler, John E

2002-01-01

Studies of ancient DNA have attracted considerable attention in scientific journals and the popular press. Several of the more extreme claims for ancient DNA have been questioned on biochemical grounds (i.e., DNA surviving longer than expected) and evolutionary grounds (i.e., nucleotide substitution patterns not matching theoretical expectations for ancient DNA). A recent letter to Nature from Vreeland et al. (2000), however, tops all others with respect to age and condition of the specimen. These researchers extracted and cultured a bacterium from an inclusion body from what they claim is a 250 million-year (Myr)-old salt crystal. If substantiated, this observation could fundamentally alter views about bacterial physiology, ecology and evolution. Here we report on molecular evolutionary analyses of the 16S rDNA from this specimen. We find that 2-9-3 differs from a modern halophile, Salibacillus marismortui, by just 3 unambiguous bp in 16S rDNA, versus the approximately 59 bp that would be expected if these bacteria evolved at the same rate as other bacteria. We show, using a Poisson distribution, that unless it can be shown that S. marismortui evolves 5 to 10 times more slowly than other bacteria for which 16S rDNA substitution rates have been established, Vreeland et al.'s claim would be rejected at the 0.05 level. Also, a molecular clock test and a relative rates test fail to substantiate Vreeland et al.'s claim that strain 2-9-3 is a 250-Myr-old bacterium. The report of Vreeland et al. thus falls into a long series of suspect ancient DNA studies.

17 CFR 250.26 - Financial statement and recordkeeping requirements for registered holding companies and...

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Financial statement and..., PUBLIC UTILITY HOLDING COMPANY ACT OF 1935 Forms, Procedure and Accounts § 250.26 Financial statement and... to form and content of financial statements; and (2) Shall make and keep current accounts, books and...

Alveolar macrophage accumulation rates, for 28 nm and 250 nm PSL, are mediated by separate mechanisms

Energy Technology Data Exchange (ETDEWEB)

Moss, O R; Wong, V A, E-mail: moss@thehamner.or [Hamner Institutes for Health Sciences, Research Triangle Park, NC 27509-2137 (United States)

2009-02-01

When macrophages accumulate 28 nm and 250 nm diameter polystyrene latex (PSL) beads, the accumulation rates should reflect differences in molecular and cellular function. We used a confocal microscope to measure the accumulation rates of nanoparticles by F344-rat-alveolar macrophages (approx25,000 cells adhered to a 0.7 cm{sup 2} surface). Over the cells were layered 0.1 ml of media, and 0.1 ml of media-with-beads. Fresh cells were introduced for each exposure scenario. The maximum possible individual macrophage exposures were as follows: 8x10{sup 6}, 8x10{sup 5}, and 8x10{sup 4} 28 nm beads per macrophage; and 8x10{sup 4} and 1.12x10{sup 4} 250 nm beads per macrophage. Accumulation rates were estimated over 23 minutes. The increase in bead accumulation-rate matched changes in bead-availability: 7x increase for 250 nm beads; 100x increase for 28 nm beads; and 700x increase for all bead availabilities. The maximum sustained 28 nm bead accumulation rate was > 30,000 /min (for 5 min). Increases in bead accumulation could be explained by two mechanisms: bead-diffusion; and, for the macrophage, macropinocytosis. Also for the highest concentrations of 28 nm beads, we saw a colligative threshold - possibly due to beads masking the cell surface or obstructing cellular mechanisms.

A kinetic-phase transformation near 250 K in potassium tetrachlorozincate

International Nuclear Information System (INIS)

Noiret, I.; Hedoux, A.; Guinet, Y.; Foulon, M.

1993-01-01

Raman-scattering experiments have been performed to study the successive phase transitions of K 2 ZnCl 4 over the temperature range (100/600) K. The spectra provide the temperature dependence of the mode frequencies and linewidths for two different spatial configurations: a(bb) c and c(aa) b. Special emphasis is put upon a new phenomenon observed in the spectra around 250 K in the c * /3 superstructure. Its kinetic character is revealed by complementary DSC measurements carried out over the range (120/300) K. This phenomenon is interpreted as a progressive structural transformation which corresponds to a slow modification of the tetrahedron distortions. (orig.)

12 CFR 250.220 - Whether member bank acting as trustee is prohibited by section 20 of the Banking Act of 1933 from...

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 3 2010-01-01 2010-01-01 false Whether member bank acting as trustee is prohibited by section 20 of the Banking Act of 1933 from acquiring majority of shares of mutual fund. 250.220 Section 250.220 Banks and Banking FEDERAL RESERVE SYSTEM (CONTINUED) BOARD OF GOVERNORS OF THE FEDERAL...

30 CFR 250.133 - Will MMS reimburse me for my expenses related to inspections?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Will MMS reimburse me for my expenses related... Inspection of Operations § 250.133 Will MMS reimburse me for my expenses related to inspections? Upon request, MMS will reimburse you for food, quarters, and transportation that you provide for MMS representatives...

Quest to validate and define performance for the high volume metallic stator PCP at 250 degrees Celsius

Energy Technology Data Exchange (ETDEWEB)

Noonan, S.G. [ConocoPhillips Co., Houston, TX (United States); Klaczek, W.; Piers, K. [C-FER Technologies, Edmonton, AB (Canada); Seince, L. [PCM USA Inc., Houston, TX (United States); Jahn, S. [Kudu Industries, Calgary, AB (Canada)

2008-10-15

ConocoPhillips has been searching for a high volume artificial lift system that will reliably operate in a 250 degree Celsius downhole environment to meet the needs of steam assisted gravity drainage (SAGD) operations. This paper described the complexity of building and operating a high temperature flow loop rated for 250 degrees Celsius. It also described the lessons learned while upgrading an existing flow loop, from the initial design, procurement and construction through to the final commissioning phases. The paper described the issues encountered with the first artificial lit system tested at 250 degrees Celsius. The system consisted of a metallic progressing cavity pump system rated for 6919 barrels per day at 500 rotations per minute. The final upgraded capabilities of the flow loop were also listed. Images of the upgraded flow loop were also provided. It was concluded that the test program not only served to validate and define the pump's performance, but also provided valuable lessons on the completion configuration and operational procedures. Testing new artificial lift technology in a controlled flow loop, rather than in field installation, provided the opportunity to test these pumping systems under a large variety of conditions to truly understand the performance and limitations of each pump. 3 refs., 1 tab., 5 figs.

Ductility in hot isostatically pressed 250-grade maraging steel

International Nuclear Information System (INIS)

German, R.M.; Smugeresky, J.E.

1978-01-01

Prealloyed 250-grade maraging steel powder produced by the rotating electrode process was fully consolidated by hot isostatic pressing (HIP) at 1100 and 1200 0 C. The strength following aging (3 h at 480 0 C) equalled that of wrought material; however, ductility was negligible. This lack of ductility in the powder metallurgy product was traced to titanium segregation which occurred at the powder surface during power production. The formation of a titanium intermetallic at the prior particle boundaries during aging caused failure at low plastic strains. Altered aging treatments successfully broke up the embrittling film and resulted in a significant ductility recovery for the HIP material. Analysis of the fracture process indicates that further ductility gains are possible by reducing the titanium content, refining the particle size, and optimizing the thermal cycles

30 CFR 250.520 - When do I have to perform a casing diagnostic test?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When do I have to perform a casing diagnostic... Operations Casing Pressure Management § 250.520 When do I have to perform a casing diagnostic test? (a) You must perform a casing diagnostic test within 30 days after first observing or imposing casing pressure...

30 CFR 250.920 - What are the MMS requirements for assessment of fixed platforms?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What are the MMS requirements for assessment of... Structures Inspection, Maintenance, and Assessment of Platforms § 250.920 What are the MMS requirements for... in API RP 2A-WSD, Section 17.3. If MMS objects to the assessment category you used for your...

HYSOGs250m, global gridded hydrologic soil groups for curve-number-based runoff modeling.

Science.gov (United States)

Ross, C Wade; Prihodko, Lara; Anchang, Julius; Kumar, Sanath; Ji, Wenjie; Hanan, Niall P

2018-05-15

Hydrologic soil groups (HSGs) are a fundamental component of the USDA curve-number (CN) method for estimation of rainfall runoff; yet these data are not readily available in a format or spatial-resolution suitable for regional- and global-scale modeling applications. We developed a globally consistent, gridded dataset defining HSGs from soil texture, bedrock depth, and groundwater. The resulting data product-HYSOGs250m-represents runoff potential at 250 m spatial resolution. Our analysis indicates that the global distribution of soil is dominated by moderately high runoff potential, followed by moderately low, high, and low runoff potential. Low runoff potential, sandy soils are found primarily in parts of the Sahara and Arabian Deserts. High runoff potential soils occur predominantly within tropical and sub-tropical regions. No clear pattern could be discerned for moderately low runoff potential soils, as they occur in arid and humid environments and at both high and low elevations. Potential applications of this data include CN-based runoff modeling, flood risk assessment, and as a covariate for biogeographical analysis of vegetation distributions.

Comparative study of 250 mg/day terbinafine and 100 mg/day itraconazole for the treatment of cutaneous sporotrichosis.

Science.gov (United States)

Francesconi, Glaucia; Francesconi do Valle, Antonio Carlos; Passos, Sonia Lambert; de Lima Barros, Mônica Bastos; de Almeida Paes, Rodrigo; Curi, André Luiz Land; Liporage, José; Porto, Cássio Ferreira; Galhardo, Maria Clara Gutierrez

2011-05-01

Itraconazole is currently used for the treatment of cutaneous sporotrichosis. Terbinafine at a daily dose of 250 mg has been successfully applied to the treatment of cutaneous sporotrichosis. To compare the efficacy of 250 mg/day terbinafine and 100 mg/day itraconazole for the treatment of cutaneous sporotrichosis. A bidirectional cohort study was conducted on 55 patients receiving 250 mg/day terbinafine and 249 patients receiving 100 mg/day itraconazole. The latter patients were matched for age and clinical form to the terbinafine group at a ratio of 5:1. Sporothrix schenckii was isolated by culture from all patients (age range: 18-70 years), who were submitted to the standard care protocol consisting of clinical and laboratory evaluation and periodic visits. Cure was observed in 51 (92.7%) patients of the terbinafine group and 229 (92%) of the itraconazole group within a similar mean period of time (11.5 and 11.8 weeks, respectively). An increase in the terbinafine dose to 500 mg was necessary in two patients due to the lack of a response, and one patient presented recurrence. In the itraconazole group, two patients required a dose increase and three presented recurrence. Adverse events were equally frequent among patients receiving terbinafine (n = 4, 7.3%) and itraconazole (n = 19, 7.6%) and were generally mild without the need for drug discontinuation, except for two patients of the itraconazole group. Terbinafine administered at a daily dose of 250 mg is an effective and well-tolerated option for the treatment of cutaneous sporotrichosis.

[Determination of 250 pesticide residues in vegetables using QuEChERS-ultra performance liquid chromatography-tandem mass spectrometry].

Science.gov (United States)

Zhang, Aizhi; Wang, Quanlin; Cao, Lili; Li, Yu; Shen, Hao; Shen, Jian; Zhang, Shufen; Man, Zhengyin

2016-02-01

A multiresidue analytical method for the determination of 250 pesticide residues in vegetables was developed by using QuEChERS-ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The target compounds were extracted with acetonitrile containing 1% (v/v) acetic acid, purified by a mixed sorbent of MgSO4, primary secondary amine (PSA), graphitized carbon black (GCB) and C18, separated on a Waters ACQUITY™ UPLC BEH C18 column (100 mm x 2. 1 mm, 1.7 µm) and detected by UPLC-MS/MS. Anhydrous magnesium sulfate was used as a dewatering agent. The effects of the amounts of MgSO4, PSA, GCB and C18 added on the recoveries of 250 pesticides were investigated. The results showed that the purification effect was best when 300 mg MgSO4, 200 mg PSA, 10 mg GCB and 100 mg C18 in 2 mL of the extract were added. For the 250 pesticide residues, the limits of detection (LODs) of the method were from 0. 01 to 50. 00 g/kg. The recoveries obtained ranged from 60. 1% to 120% at three spiked levels in Chinese chives with the relative standard deviations between 3. 5% and 19. 5% using matrix matched external standard method. The results showed that the method is able to meet requirements of the multiresidue detection of the 250 pesticides in vegetable. The method has the advantages of rapidity, simplicity, high sensitivity and better purification effect. It is suitable for the rapid determination of the common pesticides in vegetables, and it provides a strong guarantee for the risk assessments of the quality and safety of vegetables.

Shared technologies in the development of the Titan 250 gas turbine system

Energy Technology Data Exchange (ETDEWEB)

Knodle, M.S.; Novaresi, M.A. [Solar Turbines Inc., San Diego, CA (United States). Titan Gas Turbine Systems Division

2009-07-01

Development of the Titan 250 industrial gas turbine system began in 2005 in response to demands from the petroleum industry and electricity producers for higher performance industrial gas turbine products in the 15-30 MW (25,000-45,000 hp) power range. The Titan 250 is Solar Turbine's most powerful package and its evolutionary hybrid-type design approach was based on shared aerodynamic, thermal, mechanical, and combustion technologies borrowed from the Taurus 65TM, Titan 130TM, and Mercury 50TM gas turbine systems. It produces 50 per cent more power than the Titan 130, while providing 40 per cent shaft efficiency with significantly fewer emissions. Thorough combustion system testing, use of proven materials, and hot section cooling provided a solid design basis. The engine is a two-shaft design that includes a 16-stage axial-flow compressor, a dry low emissions combustor for low NOx and CO output, a two-stage gas producer turbine operating at a turbine rotor inlet temperature of 1204 degrees C, and a three-stage, all-shrouded blade power turbine for maximum efficiency. The design also minimizes maintenance intervals to increase equipment availability. The gas turbine and gas compressor have been tested in component, subsystem, and full-scale development, and will be starting field operation in late 2009 to verify performance and mechanical integrity under all operating conditions. 3 refs., 1 tab., 26 figs.

The clinical application study of bone marrow immunoscintigraphy using 99Tcm-BW250/183 in evaluating patients with aplastic anemia

International Nuclear Information System (INIS)

Liu Zengli; Wu Jinchang; Tang Jun; Wang Wei

2002-01-01

Objective: To study the clinical value of bone marrow immunoscintigraphy for evaluation of patients with aplastic anemia. Methods: Twelve patients with aplastic anemia underwent bone marrow immunoscintigraphy using 99 Tc m labelled anti-granulocyte monoclonal antibody BW250/183, 10 of them also underwent bone marrow imaging using 99 Tc m -sulfur colloid (SC) 2 - 3 days later. The semiquantitative indexes of bone marrow immunoscintigraphy of the patients were compared with those of control patients. Results: Bone marrow immunoscintigraphy was superior to 99 Tc m -SC bone marrow imaging. In patients with aplastic anemia, the accumulation of 99 Tc m -BW250/183 in bone marrow and spleen was lower and in liver and kidney was higher than those of control patients. Nine patients were found with multiple focal accumulation in bone marrow. Conclusion: Bone marrow immunoscintigraphy with 99 Tc m -BW250/183 plays an important role in evaluating patients with aplastic anemia

Flexible low-voltage organic transistors with high thermal stability at 250 °C.

Science.gov (United States)

Yokota, Tomoyuki; Kuribara, Kazunori; Tokuhara, Takeyoshi; Zschieschang, Ute; Klauk, Hagen; Takimiya, Kazuo; Sadamitsu, Yuji; Hamada, Masahiro; Sekitani, Tsuyoshi; Someya, Takao

2013-07-19

Low-operating-voltage flexible organic thin-film transistors with high thermal stability using DPh-DNTT and SAM gate dielectrics are reported. The mobility of the transistors are decreased by 23% after heating to 250 °C for 30 min. Furthermore, flexible organic pseudo-CMOS inverter circuits, which are functional after heating to 200 °C, are demonstrated. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Chemistry of pyroprocessing for nuclear waste transmutation

Energy Technology Data Exchange (ETDEWEB)

Ackerman, J.P. [Argonne National Laboratory, IL (United States)

1995-10-01

Pyrochemical treatment of spent nuclear fuel is an attractive approach for separating the transuranium (TRU) elements neptunium, plutonium, americium, and curium because of its simplicity, diversion resistance, and potentially low cost.

Homocysteine-lowering effect of 500 ug folic acid every other day versus 250 ug/day

NARCIS (Netherlands)

Brouwer, I.A.; Rooij, van I.A.L.M.; Dusseldorp, van M.; Thomas, C.M.G.; Blom, H.J.; Hautvast, J.G.A.J.; Eskes, T.K.A.B.

2000-01-01

Elevated plasma total homocysteine (tHcy) concentrations are a risk factor for neural tube defects and vascular diseases. Supplementation with folic acid decreases tHcy. We investigated whether supplementation with 500 ?g folic acid every other day is as effective in lowering tHcy as 250 ?g folic

30 CFR 250.214 - What geological and geophysical (G&G) information must accompany the EP?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What geological and geophysical (G&G... and Information Contents of Exploration Plans (ep) § 250.214 What geological and geophysical (G&G) information must accompany the EP? The following G&G information must accompany your EP: (a) Geological...

Muusikamaailm. Maailmaesiettekanne Krimmis. Herderi preemiad 2002. Opera Metz 250. Günter Wand 90 / Priit Kuusk

Index Scriptorium Estoniae

Kuusk, Priit, 1938-

2002-01-01

Krimmis leiab aset Alemdar Karamanovi sümfoonia "Täideläinu" maailma esiettekanne. Johann Gottfried Herderi muusikapreemia sai nimekas rumeenia helilooja Aurel Stroe. Opera Metz Prantsusmaal tähistab oma 250ndat aastapäeva mitmete uuslavastustega. Dirigent Günter Wand tähistab 90ndat juubelit

30 CFR 250.1157 - How do I receive approval to produce gas-cap gas from an oil reservoir with an associated gas cap?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false How do I receive approval to produce gas-cap gas from an oil reservoir with an associated gas cap? 250.1157 Section 250.1157 Mineral Resources... do I receive approval to produce gas-cap gas from an oil reservoir with an associated gas cap? (a...

Low cycle fatigue behaviour of neutron irradiated copper alloys at 250 and 350 deg. C

DEFF Research Database (Denmark)

Singh, B.N.; Stubbins, J.F.; Toft, P.

2000-01-01

V) to influence levels of 1.0 - 1.5 x 1024 n/m2 (E> 1 MeV) at 250 and 350 deg. C. These irradiations were carried out in temperature controlled rigs where the irradiation temperature was monitored and controlledcontinuously throughout the whole irradiation experiment. Both unirradiated and irradiated speciments...

Design of the proposed 250 MeV superconducting cyclotron magnet for proton therapy

International Nuclear Information System (INIS)

Dey, M.K.; Ahmed, M.; Murali, S.; Duttagupta, A.; Chaudhuri, J.; Mallik, C.; Bhandari, R.K.

2006-01-01

Here we describe the design calculations for the superconducting magnet of a 250 MeV proton cyclotron to be used for therapeutic purpose. Hard-edge approximation method has been adopted for finding the poletip geometry to meet the basic focusing requirements of the beam. Then the uniform-magnetization method has been applied to calculate the 3D magnetic field distribution due to saturated iron poletips, to verify the beam dynamical issues. (author)

Report on the scientifical feasibility of advanced separation

International Nuclear Information System (INIS)

2001-01-01

The advanced separation process Purex has been retained for the recovery of neptunium, technetium and iodine from high level and long lived radioactive wastes. Complementary solvent extraction processes will be used for the recovery of americium, curium and cesium from the high activity effluents of the spent fuel reprocessing treatment. This document presents the researches carried out to demonstrate the scientifical feasibility of the advanced separation processes: the adaptation of the Purex process would allow the recovery of 99% of the neptunium, while the association of the Diamex and Sanex (low acidity variant) processes, or the Paladin concept (single cycle with selective de-extraction of actinides) make it possible the recovery of 99.8% of the actinides III (americium and curium) with a high lanthanides decontamination factor (greater than 150). The feasibility of the americium/curium separation is demonstrated with the Sesame process (extraction of americium IV after electrolytic oxidation). Iodine is today recovered at about 99% with the Purex process and the dissolved fraction of technetium is also recovered at 99% using an adaptation of the Purex process. The non-dissolved fraction is retained by intermetallic compounds in dissolution residues. Cesium is separable from other fission products with recovery levels greater than 99.9% thanks to the use of functionalized calixarenes. The scientifical feasibility of advanced separation is thus demonstrated. (J.S.)

Polarized electrons from GaAs for parity nonconservation studies and Moeller scattering at 250 MeV

International Nuclear Information System (INIS)

Cates, G.D. Jr.

1987-01-01

A description is given of a polarized electron source based on photoemission from GaAs with circularly polarized light, which was developed for use in the study of parity nonconservation (PNC) in e- 12 C scattering at 250 MeV at the MIT Bates Linear Accelerator Center. A multi-chamber vacuum system houses up to four GaAs crystals simultaneously, and is contained in a Faraday cage to provide 365 KeV in electrostatic acceleration. Stable operation is achieved through the use of a modulated cw laser. The PNC experiment is discussed, particularly with regards to its requirements on the source. The peak current from the source is 20 mA, resulting in a current in excess of 6 mA at high energy. The electron beam polarization has been measured to be 0.36 ± 0.004 using Moeller scattering at 250 MeV

NIR-Red Spectra-Based Disaggregation of SMAP Soil Moisture to 250 m Resolution Based on SMAPEx-4/5 in Southeastern Australia

Directory of Open Access Journals (Sweden)

Nengcheng Chen

2017-01-01

Full Text Available To meet the demand of regional hydrological and agricultural applications, a new method named near infrared-red (NIR-red spectra-based disaggregation (NRSD was proposed to perform a disaggregation of Soil Moisture Active Passive (SMAP products from 36 km to 250 m resolution. The NRSD combined proposed normalized soil moisture index (NSMI with SMAP data to obtain 250 m resolution soil moisture mapping. The experiment was conducted in southeastern Australia during SMAP Experiments (SMAPEx 4/5 and validated with the in situ SMAPEx network. Results showed that NRSD performed a decent downscaling (root-mean-square error (RMSE = 0.04 m3/m3 and 0.12 m3/m3 during SMAPEx-4 and SMAPEx-5, respectively. Based on the validation, it was found that the proposed NSMI was a new alternative indicator for denoting the heterogeneity of soil moisture at sub-kilometer scales. Attributed to the excellent performance of the NSMI, NRSD has a higher overall accuracy, finer spatial representation within SMAP pixels and wider applicable scope on usability tests for land cover, vegetation density and drought condition than the disaggregation based on physical and theoretical scale change (DISPATCH has at 250 m resolution. This revealed that the NRSD method is expected to provide soil moisture mapping at 250-resolution for large-scale hydrological and agricultural studies.

Pharmacokinetics and tumor targeting of 131I-labeled F(ab')2 fragments of the chimeric monoclonal antibody G250: preclinical and clinical pilot studies.

NARCIS (Netherlands)

Brouwers, A.H.; Mulders, P.F.A.; Oosterwijk, E.; Buijs, W.C.A.M.; Corstens, F.H.M.; Boerman, O.C.; Oyen, W.J.G.

2004-01-01

INTRODUCTION: Clinical and animal studies of chimeric monoclonal antibody G250 (moAb cG250) for the targeting of clear-cell renal cell carcinoma (RCC), to date, have been with the intact IgG form. To determine whether F(ab')2 fragments are more suited for radioimmunotherapy (RIT) than intact IgG,

Three-electrode pulse electron gun with currents up to 250 A

International Nuclear Information System (INIS)

Grigor'ev, Yu.V.; Shanturin, L.P.

1977-01-01

The design and operating conditions of a pulsed electron gun are described. The electron gun has three electrodes: a cathode, an anode and a control electrode in the form of a grid. The cathode is made from lanthanum hexaboride, which ensures its operation in a low vacuum at a temperature of 1,700 deg C. The control electrode and anode grid are fabricated from sheet tantalum. The anode-grid characteristics of the gun are given. It is shown that at an accelerating voltage of 100 kV, a temperature of 1,700 deg C and a zero control electrode potential the beam current is 250 A

Investigations in a drift chamber using 250 MHz analogue-digital-converters

International Nuclear Information System (INIS)

Scharf, F.A.

1993-06-01

The performance of a new 250 MHz FADC module was investigated in a small drift chamber system. Straight tracks were induced in the chamber volume by UV-LASER beams. The time resolution was determined from drift time measurements for four neighbouring signal wires. By use of a beam splitter a pair of parallel beams was produced. An appropriate rotation of this pair relative to the signal wire plane allowed the determination of the double hit resolution. A comparison of the obtained values with the results achieved with 100 MHz FADC modules showed that the new module is well suited for chamber read out. The attainable improvements however are small. (orig.) [de

Ultrasonic Characterization of Aging Behavior in M250 Grade Maraging Steel

Science.gov (United States)

Yeheskel, Ori

2009-03-01

The increase in sound velocities during the aging of M250 maraging steel reported by Rajkumar et al. was analyzed. The present article provides a new perspective on why and to what extent the sound velocities change during aging. The main parameter that affects the elastic moduli and the sound velocities in the early and intermediate stages of aging in maraging steel is the depletion of Ni from the martensitic matrix due to Ni3Ti and Ni3Mo formation. The issue of sound velocity increase with aging time was addressed here in a few different ways to support the validity of Ni depletion.

Dense grid of narrow bandpass filters for the JST/T250 telescope: summary of results

Science.gov (United States)

Brauneck, Ulf; Sprengard, Ruediger; Bourquin, Sebastien; Marín-Franch, Antonio

2018-01-01

On the Javalambre mountain in Spain, the Centro de Estudios de Fisica del Cosmos de Aragon has setup two telescopes, the JST/T250 and the JAST/T80. The JAST/T80 telescope integrates T80Cam, a large format, single CCD camera while the JST/T250 will mount the JPCam instrument, a 1.2Gpix camera equipped with a 14-CCD mosaic using the new large format e2v 9.2k×9.2k 10-μm pixel detectors. Both T80Cam and JPCam integrate a large number of filters in dimensions of 106.8×106.8 mm2 and 101.7×95.5 mm2, respectively. For this instrument, SCHOTT manufactured 56 specially designed steep edged bandpass interference filters, which were recently completed. The filter set consists of bandpass filters in the range between 348.5 and 910 nm and a longpass filter at 915 nm. Most of the filters have full-width at half-maximum (FWHM) of 14.5 nm and a blocking between 250 and 1050 nm with optical density of OD5. Absorptive color glass substrates in combination with interference filters were used to minimize residual reflection in order to avoid ghost images. In spite of containing absorptive elements, the filters show the maximum possible transmission. This was achieved by using magnetron sputtering for the filter coating process. The most important requirement for the continuous photometric survey is the tight tolerancing of the central wavelengths and FWHM of the filters. This insures each bandpass has a defined overlap with its neighbors. A high image quality required a low transmitted wavefront error (<λ/4 locally and <λ/2 on the whole aperture), which was achieved even by combining two or three substrates. We report on the spectral and interferometric results measured on the whole set of filters.

Estimating Coastal Turbidity using MODIS 250 m Band Observations

Science.gov (United States)

Davies, James E.; Moeller, Christopher C.; Gunshor, Mathew M.; Menzel, W. Paul; Walker, Nan D.

2004-01-01

Terra MODIS 250 m observations are being applied to a Suspended Sediment Concentration (SSC) algorithm that is under development for coastal case 2 waters where reflectance is dominated by sediment entrained in major fluvial outflows. An atmospheric correction based on MODIS observations in the 500 m resolution 1.6 and 2.1 micron bands is used to isolate the remote sensing reflectance in the MODIS 25Om resolution 650 and 865 nanometer bands. SSC estimates from remote sensing reflectance are based on accepted inherent optical properties of sediment types known to be prevalent in the U.S. Gulf of Mexico coastal zone. We present our findings for the Atchafalaya Bay region of the Louisiana Coast, in the form of processed imagery over the annual cycle. We also apply our algorithm to selected sites worldwide with a goal of extending the utility of our approach to the global direct broadcast community.

20 CFR 404.250 - Special computation rules for people who had a period of disability.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Special computation rules for people who had... Computation Rules for People Who Had A Period of Disability § 404.250 Special computation rules for people who had a period of disability. If you were disabled at some time in your life, received disability...

Sorption studies of radioelements on geological materials

International Nuclear Information System (INIS)

Berry, John A.; Yui, Mikazu; Kitamura, Akira

2007-11-01

Batch sorption experiments have been carried out to study the sorption of uranium, technetium, curium, neptunium, actinium, protactinium, polonium, americium and plutonium onto bentonite, granodiorite and tuff. Mathematical modelling using the HARPHRQ program and the HATCHES database was carried out to predict the speciation of uranium and technetium in the equilibrated seawater, and neptunium, americium and plutonium in the rock equilibrated water. Review of the literature for thermodynamic data for curium, actinium, protactinium and polonium was carried out. Where sufficient data were available, predictions of the speciation and solubility were made. This report is a summary report of the experimental work conducted by AEA Technology during April 1991-March 1998, and the main results have been presented at Material Research Society Symposium Proceedings and published as proceedings of them. (author)

30 CFR 250.182 - When may the Secretary cancel a lease at the exploration stage?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When may the Secretary cancel a lease at the... Requirements, Lease Term Extensions, and Lease Cancellations § 250.182 When may the Secretary cancel a lease at... be modified to avoid the condition(s). The Secretary may cancel the lease if: (a) The primary lease...

76 FR 41045 - Special Conditions; Gulfstream Aerospace LP (GALP) Model G250 Airplane, Design Roll-Maneuver...

Science.gov (United States)

2011-07-13

... issue a finding of regulatory adequacy under Sec. 611 of Public Law 92-574, the ``Noise Control Act of... with electronic flight controls as they relate to design roll-maneuver requirements. The applicable... G250 airplane is equipped with an electronic flight control system that provides control through the...

Dynamic aperture calculation for 100 GeV Au-Au and 250 GeV pp lattices with near third order resonance working point

International Nuclear Information System (INIS)

Gu, X.; Luo, Y.; Fischer, W.

2010-01-01

In the preparation for the 2011 RHIC 250 GeV polarized proton (pp) run, both experiment and simulation were carried out to investigate the possibility to accelerate the proton beam with a vertical tune near 2/3. It had been found experimentally in Run-9 that accelerating the proton beam with a vertical tune close to 2/3 will greatly benefit the transmission of the proton polarization. In this note, we report the calculated dynamic apertures with the 100 GeV Au run and 250 GeV proton run lattices with vertical tunes close to the third order resonance. We will compare the third order resonance band width between the beam experiment and the simulation with the 100 GeV Au lattices. And we also will compare the calculated resonance band width between the 100 GeV Au and 250 GeV proton run lattices.

Radiation vulcanization of natural rubber latex using 250 keV electron beam machine

Energy Technology Data Exchange (ETDEWEB)

Chirinos, H.; Yoshii, F.; Makuuchi, K.; Lugao, A. E-mail: ablugao@net.ipen.br

2003-08-01

The sensitized radiation vulcanization of natural rubber latex has been carried out with 250 keV electrons. Latex was irradiated over a range of the beam current from 5 to 20 mA in the presence of sensitizers like the n-butyl acrylate (n-BA). The vulcanization dose decreases with increasing beam current condition. The rate of vulcanization (R{sub vul}) depends on the beam current (I) as given by the equation R{sub vul}=kI{sup 0.6}.

Analysis of the in vitro cleavage products of the tomato black ring virus RNA-1-encoded 250K polyprotein.

Science.gov (United States)

Demangeat, G; Greif, C; Hemmer, O; Fritsch, C

1990-08-01

Tomato black ring virus RNA-1 was translated in a rabbit reticulocyte lysate. The primary translation product of Mr 250K, which corresponds to its whole coding capacity, was synthesized within 45 min and, during further incubation in the translation medium, was proteolytically processed. Essentially, four cleavage products (P190, P120, P60 and P50) were detected and located within P250 by pulse-chase and immunoprecipitation experiments. P190 is an intermediate cleavage product which is further cleaved to form P60 and P120. P120, which contains the region that has been assigned to the virus protease and the virus polymerase, was not further cleaved in vitro.

Performances of 250 Amp-hr lithium/thionyl chloride cells

Science.gov (United States)

Goualard, Jacques

1991-01-01

A 250 Ah lithium thionyl chloride battery is being developed for a booster rocket engine. Extensive cell testing is running to evaluate functional and safety performances. Some results are presented. The lithium/thionyl chloride batteries were selected for their high energy density (low weight) as compared to other sources. The temperature of a lower weight item will be more sensitive to variations of internal and external heat fluxes than a heavier one. The use of high energy density L/TC batteries is subjected to stringent thermal environments to have benefit of energy density and to stay safe in any conditions. The battery thermal environment and discharge rate have to be adjusted to obtain the right temperature range at cell level, to have the maximum performances. Voltage and capacity are very sensitive to temperature. This temperature is the cell internal actual temperature during discharge. This temperature is directed by external thermal environment and by cell internal heat dissipation, i.e., cell actual voltage.

Performances of 250 Amp-hr lithium/thionyl chloride cells

Science.gov (United States)

Goualard, Jacques

1991-05-01

A 250 Ah lithium thionyl chloride battery is being developed for a booster rocket engine. Extensive cell testing is running to evaluate functional and safety performances. Some results are presented. The lithium/thionyl chloride batteries were selected for their high energy density (low weight) as compared to other sources. The temperature of a lower weight item will be more sensitive to variations of internal and external heat fluxes than a heavier one. The use of high energy density L/TC batteries is subjected to stringent thermal environments to have benefit of energy density and to stay safe in any conditions. The battery thermal environment and discharge rate have to be adjusted to obtain the right temperature range at cell level, to have the maximum performances. Voltage and capacity are very sensitive to temperature. This temperature is the cell internal actual temperature during discharge. This temperature is directed by external thermal environment and by cell internal heat dissipation, i.e., cell actual voltage.

Properties of PZT-Based Piezoelectric Ceramics Between -150 and 250 C

Science.gov (United States)

Hooker, Matthew W.

1998-01-01

The properties of three PZT-based piezoelectric ceramics and one PLZT electrostrictive ceramic were measured as a function of temperature. In this work, the dielectric, ferroelectric polarization versus electric field, and piezoelectric properties of PZT-4, PZT-5A, PZT-5H, and PLZT-9/65/35 were measured over a temperature range of -150 to 250 C. In addition to these measurements, the relative thermal expansion of each composition was measured from 25 to 600 C and the modulus of rupture of each material was measured at room temperature. This report describes the experimental results and compares and contrasts the properties of these materials with respect to their applicability to intelligent aerospace systems.

30 CFR 250.108 - What requirements must I follow for cranes and other material-handling equipment?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What requirements must I follow for cranes and... Performance Standards § 250.108 What requirements must I follow for cranes and other material-handling equipment? (a) All cranes installed on fixed platforms must be operated in accordance with American...

Analysis of MODIS 250 m Time Series Product for LULC Classification and Retrieval of Crop Biophysical Parameter

Science.gov (United States)

Verma, A. K.; Garg, P. K.; Prasad, K. S. H.; Dadhwal, V. K.

2016-12-01

Agriculture is a backbone of Indian economy, providing livelihood to about 70% of the population. The primary objective of this research is to investigate the general applicability of time-series MODIS 250m Normalized difference vegetation index (NDVI) and Enhanced vegetation index (EVI) data for various Land use/Land cover (LULC) classification. The other objective is the retrieval of crop biophysical parameter using MODIS 250m resolution data. The Uttar Pradesh state of India is selected for this research work. A field study of 38 farms was conducted during entire crop season of the year 2015 to evaluate the applicability of MODIS 8-day, 250m resolution composite images for assessment of crop condition. The spectroradiometer is used for ground reflectance and the AccuPAR LP-80 Ceptometer is used to measure the agricultural crops Leaf Area Index (LAI). The AccuPAR measures Photosynthetically Active Radiation (PAR) and can invert these readings to give LAI for plant canopy. Ground-based canopy reflectance and LAI were used to calibrate a radiative transfer model to create look-up table (LUT) that was used to simulate LAI. The seasonal trend of MODIS-derived LAI was used to find crop parameter by adjusting the LAI simulated from climate-based crop yield model. Cloud free MODIS images of 250m resolution (16 day composite period) were downloaded using LP-DAAC website over a period of 12 months (Jan to Dec 2015). MODIS both the VI products were found to have sufficient spectral, spatial and temporal resolution to detect unique signatures for each class (water, fallow land, urban, dense vegetation, orchard, sugarcane and other crops). Ground truth data were collected using JUNO GPS. Multi-temporal VI signatures for vegetation classes were consistent with its general phenological characteristic and were spectrally separable at some point during the growing season. The MODIS NDVI and EVI multi-temporal images tracked similar seasonal responses for all croplands and were

Transfer free graphene growth on SiO2 substrate at 250 °C

Science.gov (United States)

Vishwakarma, Riteshkumar; Rosmi, Mohamad Saufi; Takahashi, Kazunari; Wakamatsu, Yuji; Yaakob, Yazid; Araby, Mona Ibrahim; Kalita, Golap; Kitazawa, Masashi; Tanemura, Masaki

2017-03-01

Low-temperature growth, as well as the transfer free growth on substrates, is the major concern of graphene research for its practical applications. Here we propose a simple method to achieve the transfer free graphene growth on SiO2 covered Si (SiO2/Si) substrate at 250 °C based on a solid-liquid-solid reaction. The key to this approach is the catalyst metal, which is not popular for graphene growth by chemical vapor deposition. A catalyst metal film of 500 nm thick was deposited onto an amorphous C (50 nm thick) coated SiO2/Si substrate. The sample was then annealed at 250 °C under vacuum condition. Raman spectra measured after the removal of the catalyst by chemical etching showed intense G and 2D peaks together with a small D and intense SiO2 related peaks, confirming the transfer free growth of multilayer graphene on SiO2/Si. The domain size of the graphene confirmed by optical microscope and atomic force microscope was about 5 μm in an average. Thus, this approach will open up a new route for transfer free graphene growth at low temperatures.

Radiation damage studies on STAR250 CMOS sensor at 300 keV for electron microscopy

International Nuclear Information System (INIS)

Faruqi, A.R.; Henderson, R.; Holmes, J.

2006-01-01

There is a pressing need for better electronic detectors to replace film for recording high-resolution images using electron cryomicroscopy. Our previous work has shown that direct electron detection in CMOS sensors is promising in terms of resolution and efficiency at 120 keV [A.R. Faruqi, R. Henderson, M. Prydderch, R. Turchetta, P. Allport, A. Evans, Nucl. Instr. and Meth. 546 (2005) 170], but in addition, the detectors must not be damaged by the electron irradiation. We now present new measurements on the radiation tolerance of a 25 μm pitch CMOS active-pixel sensor, the STAR250, which was designed by FillFactory using radiation-hard technology for space applications. Our tests on the STAR250 aimed to establish the imaging performance at 300 keV following irradiation. The residual contrast, measured on shadow images of a 300 mesh grid, was >80% after corrections for increased dark current, following irradiation with up to 5x10 7 electrons/pixel (equivalent to 80,000 electron/μm 2 ). A CMOS sensor with this degree of radiation tolerance would survive a year of normal usage for low-dose electron cryomicroscopy, which is a very useful advance

47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. 25.250 Section 25.250 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Technical Standards § 25...

30 CFR 250.524 - When am I required to take action from my casing diagnostic test?

Science.gov (United States)

2010-07-01

... pressure (MAWOP); (b) Any fixed platform well with a casing pressure that is greater than 100 psig and that... bled down to prevent it from exceeding its MAWOP, except during initial startup operations described in § 250.521; (e) Any hybrid well with casing or riser pressure exceeding 100 psig; or (f) Any subsea well...

Two different mechanisms associated with ripple-like oscillations (100-250 Hz) in the human epileptic subiculum in vitro

Science.gov (United States)

Alvarado-Rojas, C; Huberfeld, G; Baulac, M; Clemenceau, S; Charpier, S; Miles, R; Menendez de la Prida, L; Le Van Quyen, M

2015-01-01

Transient high-frequency oscillations (150-600 Hz) in local field potential generated by human hippocampal and parahippocampal areas have been related to both physiological and pathological processes. The cellular basis and effects of normal and abnormal forms of high-frequency oscillations (HFO) has been controversial. Here, we searched for HFOs in slices of the subiculum prepared from human hippocampal tissue resected for treatment of pharmacoresistant epilepsy. HFOs occurred spontaneously in extracellular field potentials during interictal discharges (IID) and also during pharmacologically induced preictal discharges (PID) preceding ictal-like events. While most of these events might be considered pathological since they invaded the fast ripple band (>250 Hz), others were spectrally similar to physiological ripples (150-250 Hz). Do similar cellular mechanisms underly IID-ripples and PID-ripples? Are ripple-like oscillations a valid proxy of epileptogenesis in human TLE? With combined intra- or juxta-cellular and extracellular recordings, we showed that, despite overlapping spectral components, ripple-like IID and PID oscillations were associated with different cellular and synaptic mechanisms. IID-ripples were associated with rhythmic GABAergic and glutamatergic synaptic potentials with moderate neuronal firing. In contrast, PID-ripples were associated with depolarizing synaptic inputs frequently reaching the threshold for bursting in most cells. Thus ripple-like oscillations (100-250 Hz) in the human epileptic hippocampus are associated with different mechanisms for synchrony reflecting distinct dynamic changes in inhibition and excitation during interictal and pre-ictal states. PMID:25448920

Fabrication and Pre-irradiation Characterization of a Minor Actinide and Rare Earth Containing Fast Reactor Fuel Experiment for Irradiation in the Advanced Test Reactor

Energy Technology Data Exchange (ETDEWEB)

Timothy A. Hyde

2012-06-01

The United States Department of Energy, seeks to develop and demonstrate the technologies needed to transmute the long-lived transuranic actinide isotopes contained in spent nuclear fuel into shorter lived fission products, thereby decreasing the volume of material requiring disposal and reducing the long-term radiotoxicity and heat load of high-level waste sent to a geologic repository. This transmutation of the long lived actinides plutonium, neptunium, americium and curium can be accomplished by first separating them from spent Light Water Reactor fuel using a pyro-metalurgical process, then reprocessing them into new fuel with fresh uranium additions, and then transmuted to short lived nuclides in a liquid metal cooled fast reactor. An important component of the technology is developing actinide-bearing fuel forms containing plutonium, neptunium, americium and curium isotopes that meet the stringent requirements of reactor fuels and materials.

On possibility of transuranium element by the method of transport reactions

International Nuclear Information System (INIS)

Sinitsyna, G.S.; Krashenitsyn, G.N.; Shestakov, B.I.

1983-01-01

A possibility to use chemical transport reaction for separation of uranium, plutonium and some transplutonium elements is shown. The method is based on the use of the known plutonium property to form tetrachloride existing only in the gaseous phase in chlorine atmosphere, which is transported ever the temperature gradiept. Two ways of transport reaction realization - the method of flow and the method of diffusion in closed volume are tested. The experiments are made using specially synthesized plutonium dioxide, containing uranium, americium, curium, lanthanum, terbium, barium. Chlorination is realized by the mixture of chlorine and carbon tetrachloride at temperatures 723-953 K. Plutonium trichloride is deposited in the range 613-653 K, uranium - in the range 473-523 K, curium, americium, lanthanum, terbium, barium remain in the start zone if its temperature does not exceed 873 K

MODIS/Terra Land Water Mask Derived from MODIS and SRTM L3 Global 250m SIN Grid V005

Data.gov (United States)

National Aeronautics and Space Administration — The MODIS 250 m land-water mask (Short Name: MOD44W) is an improvement over the existing MODIS Nadir Bidirectional Reflectance Distribution Function (BRDF)-Adjusted...

A 250-Mbit/s ring local computer network using 1.3-microns single-mode optical fibers

Science.gov (United States)

Eng, S. T.; Tell, R.; Andersson, T.; Eng, B.

1985-01-01

A 250-Mbit/s three-station fiber-optic ring local computer network was built and successfully demonstrated. A conventional token protocol was employed for bus arbitration to maximize the bus efficiency under high loading conditions, and a non-return-to-zero (NRS) data encoding format was selected for simplicity and maximum utilization of the ECL-circuit bandwidth.

Test results from the LLNL 250 GHz CARM experiment

International Nuclear Information System (INIS)

Kulke, B.; Caplan, M.; Bubp, D.; Houck, T.; Rogers, D.; Trimble, D.; VanMaren, R.; Westenskow, G.; McDermott, D.B.; Luhmann, N.C. Jr.; Danly, B.

1991-05-01

We have completed the initial phase of a 250 GHz CARM experiment, driven by the 2 MeV, 1 kA, 30 ns induction linac at the LLNL ARC facility. A non-Brillouin, solid, electron beam is generated from a flux-threaded, thermionic cathode. As the beam traverses a 10 kG plateau produced by a superconducting magnet, ten percent of the beam energy is converted into rotational energy in a bifilar helix wiggler that produces a spiraling, 50 G, transverse magnetic field. The beam is then compressed to a 5 mm diameter as it drifts into a 30 kG plateau. For the present experiment, the CARM interaction region consisted of a single Bragg section resonator, followed by a smooth-bore amplifier section. Using high-pass filters, we have observed broadband output signals estimated to be at the several megawatt level in the range 140 to over 230 GHz. This is consistent with operation as a superradiant amplifier. Simultaneously, we also observed K a band power levels near 3 MW

Test results from the LLNL 250 GHz CARM experiment

International Nuclear Information System (INIS)

Kulke, B.; Caplan, M.; Bubp, D.; Houck, T.; Rogers, D.; Trimble, D.; VanMaren, R.; Westenskow, G.; McDermott, D.B.; Luhmann, N.C. Jr.; Danly, B.

1991-01-01

The authors have completed the initial phase of a 250 GHz CARM experiment, driven by the 2 MeV, 1 kA, 30 ns induction linac at the LLNL ARC facility. A non-Brillouin, solid, electron beam is generated from a flux-threaded, thermionic cathode. As the beam traverses a 10 kG plateau produced by a superconducting magnet, ten percent of the beam energy is converted into rotational energy in a bifilar helix wiggler that produces a spiraling, 50 G, transverse magnetic field. The beam is then compressed to a 5 mm diameter as it drifts into a 30 kG plateau. For the present experiment, the CARM interaction region consisted of a single Bragg section resonator, followed by a smooth-bore amplifier section. Using high-pass filters, they have observed broadband output signals estimated to be at the several megawatt level in the range 140 to over 230 GHz. This is consistent with operation as a superradiant amplifier. Simultaneously, they also observed K a band power levels near 3 MW

Predicted Performance of a Dc Beam Driven Fem Oscillator Designed for Fusion Applications at 200-250 Ghz

NARCIS (Netherlands)

Caplan, M.; Best, R. W. B.; Verhoeven, A. G. A.; van der Wiel, M. J.; Urbanus, W. H.; Bratman, V. L.; Denisov, G. G.

1993-01-01

At the FOM Institute (The Netherlands) a free electron laser using a dc beam with depressed collector is being developed for plasma heating, which will be capable of producing 1 MW cw output over an adjustable tuning range of 200-250 GHz. The basic design parameters for the electron beam, undulator

30 CFR 250.244 - What geological and geophysical (G&G) information must accompany the DPP or DOCD?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What geological and geophysical (G&G... Operations Coordination Documents (docd) § 250.244 What geological and geophysical (G&G) information must accompany the DPP or DOCD? The following G&G information must accompany your DPP or DOCD: (a) Geological...

Snow Cover Maps from MODIS Images at 250 m Resolution, Part 2: Validation

Directory of Open Access Journals (Sweden)

Marc Zebisch

2013-03-01

Full Text Available The performance of a new algorithm for binary snow cover monitoring based on Moderate Resolution Imaging Spectroradiometer (MODIS satellite images at 250 m resolution is validated using snow cover maps (SCA based on Landsat 7 ETM+ images and in situ snow depth measurements from ground stations in selected test sites in Central Europe. The advantages of the proposed algorithm are the improved ground resolution of 250 m and the near real-time availability with respect to the 500 m standard National Aeronautics and Space Administration (NASA MODIS snow products (MOD10 and MYD10. It allows a more accurate snow cover monitoring at a local scale, especially in mountainous areas characterized by large landscape heterogeneity. The near real-time delivery makes the product valuable as input for hydrological models, e.g., for flood forecast. A comparison to sixteen snow cover maps derived from Landsat ETM/ETM+ showed an overall accuracy of 88.1%, which increases to 93.6% in areas outside of forests. A comparison of the SCA derived from the proposed algorithm with standard MODIS products, MYD10 and MOD10, indicates an agreement of around 85.4% with major discrepancies in forested areas. The validation of MODIS snow cover maps with 148 in situ snow depth measurements shows an accuracy ranging from 94% to around 82%, where the lowest accuracies is found in very rugged terrain restricted to in situ stations along north facing slopes, which lie in shadow in winter during the early morning acquisition.

Structure function scaling in a Reλ = 250 turbulent mixing layer

KAUST Repository

Attili, Antonio

2011-12-22

A highly resolved Direct Numerical Simulation of a spatially developing turbulent mixing layer is presented. In the fully developed region, the flow achieves a turbulent Reynolds number Reλ = 250, high enough for a clear separation between large and dissipative scales, so for the presence of an inertial range. Structure functions have been calculated in the self-similar region using velocity time series and Taylor\\'s frozen turbulence hypothesis. The Extended Self-Similarity (ESS) concept has been employed to evaluate relative scaling exponents. A wide range of scales with scaling exponents and intermittency levels equal to homogeneous isotropic turbulence has been identified. Moreover an additional scaling range exists for larger scales; it is characterized by smaller exponents, similar to the values reported in the literature for flows with strong shear.

Structure function scaling in a Reλ = 250 turbulent mixing layer

KAUST Repository

Attili, Antonio; Bisetti, Fabrizio

2011-01-01

A highly resolved Direct Numerical Simulation of a spatially developing turbulent mixing layer is presented. In the fully developed region, the flow achieves a turbulent Reynolds number Reλ = 250, high enough for a clear separation between large and dissipative scales, so for the presence of an inertial range. Structure functions have been calculated in the self-similar region using velocity time series and Taylor's frozen turbulence hypothesis. The Extended Self-Similarity (ESS) concept has been employed to evaluate relative scaling exponents. A wide range of scales with scaling exponents and intermittency levels equal to homogeneous isotropic turbulence has been identified. Moreover an additional scaling range exists for larger scales; it is characterized by smaller exponents, similar to the values reported in the literature for flows with strong shear.

Relationship between thermal embrittlement and hydrogen cracking in 18Ni(250) maraging steel

International Nuclear Information System (INIS)

Rack, H.J.

1974-01-01

The role of grain boundary precipitate structure on the stress corrosion susceptibility of 18Ni(250) maraging steel was examined. Varying solution treatment procedures were used to achieve either a precipitate-free grain boundary or one containing a high density of Ti(C,N) particles. The introduction of these treatments, although drastically affecting the monotonic fracture toughness, did not significantly alter the stress corrosion threshold in 100 percent relative humidity. These results are shown to be consistent with the previous suggestion that, under open circuit conditions, hydrogen-assisted cracking controls the environmental crack growth behavior of 18Ni maraging steels. (U.S.)

Hypothetical accident scenario analyses for a 250-MW(t) modular high temperature gas-cooled reactor

International Nuclear Information System (INIS)

Harrington, R.M.; Ball, S.J.; Cleveland, J.C.

1985-11-01

This paper describes calculations performed to characterize the inherent safety of a 250-MW(t), 100-MW(e), pebble bed modular high temperature gas-cooled reactor (HTGR) design with vertical in-line arrangement (i.e., upflow core with steam generators directly above the core). A variety of postulated accident sequences involving combinations of loss of forced primary coolant (helium) circulation, loss of primary coolant pressurization, and loss of heat sink were studied and were discussed

Motor power calculation for driving conveyor chain in gamma irradiator BATAN 2x250 k curie

International Nuclear Information System (INIS)

Ari Satmoko; Syamsurrijal Ramdja; Sutomo Budihardjo

2010-01-01

Recently, an Irradiator BATAN 2X250 k Curie for agricultural product is under design. The installation is provided by the gamma source about 2x250 k Curie. Agricultural products are carried into carriers and these carriers are hanged on the conveyor chain. The chain moves into a radiation chamber following the trajectoire. The chain is drived by motor. For this reason, the calculation is performed to determine the motor power. After resolving the force equilibrium equation, the force and power of the motor needed to drive the chain are obtained. Numerical method by using V Basic language is used to resolve the equation. The calculation result shows the correlation between friction coefficient and motor power. From the evaluation, it is decided that the friction coefficient should be less than 0,015. By this friction, the motor power is about 3. 13 k Watt. From the evaluation, it is also obtained that the radius of the curve trajectory shall not be too small. Combination between high friction and small curve radius could lead to the locked condition in which high power motor are not be able to move the conveyor chain). (author)

Bionics by examples 250 scenarios from classical to modern times

CERN Document Server

Nachtigall, Werner

2015-01-01

Bionics means learning from the nature for the development of technology. The science of "bionics" itself is classified into several sections, from materials and structures over procedures and processes until evolution and optimization. Not all these areas, or only a few, are really known in the public and also in scientific literature. This includes the Lotus-effect, converted to the contamination-reduction of fassades and the shark-shed-effect, converted to the  resistance-reduction of airplanes. However, there are hundreds of highly interesting examples that contain the transformation of principles of the nature into technology. From the large number of these examples, 250 were selected for the present book according to "prehistory", "early-history", "classic" and "modern time". Most examples are new. Every example includes a printed page in a homogeneous arrangement. The examples from the field "modern time" are joint in blocks corresponding to the sub-disciplines of bionics.

17 CFR 250.53 - Certain registered holding company financings in connection with the acquisition of one or more...

Science.gov (United States)

2010-04-01

... Financial Transactions 2 § 250.53 Certain registered holding company financings in connection with the acquisition of one or more exempt wholesale generators. (a) In determining whether to approve the issue or... shall be kept in conformity with United States generally accepted accounting principles (“GAAP”). (B...

Quantum-chemical consideration of extermal valent forms of actinides

International Nuclear Information System (INIS)

Ionova, G.V.; Pershina, V.G.; Spitsyn, V.I.

1982-01-01

Stability of valent forms of actinides that has not yet studied experimentally, is considered within the framework of quantum-chemical considerations. Oxidizing potentials E 0 for actinide elements are determined theoretically. A dependence of the definite valent state stability on relativistic effect is shown. A conclusion is made that oxidizing potential E 0 (4-5) for americium should be higher than E 0 (4-5) for plutonium. A relatively small oxidizing potential E 0 (4-5) for curium speaks about principle possibility of production of five-valent curium in solution, though it is less stable than the six-valent one. Oxidizing potential corresponding to transition of three-valent californium into the four-valent state should be less than the value adopted in literature. A relatively small oxidizing potential of californium E 0 (4-5) speaks about possible existence of five-valent californium in solution

Radionuclide and Fluorescence Imaging of Clear Cell Renal Cell Carcinoma Using Dual Labeled Anti-Carbonic Anhydrase IX Antibody G250.

Science.gov (United States)

Muselaers, Constantijn H J; Rijpkema, Mark; Bos, Desirée L; Langenhuijsen, Johan F; Oyen, Wim J G; Mulders, Peter F A; Oosterwijk, Egbert; Boerman, Otto C

2015-08-01

Tumor targeted optical imaging using antibodies labeled with near infrared fluorophores is a sensitive imaging modality that might be used during surgery to assure complete removal of malignant tissue. We evaluated the feasibility of dual modality imaging and image guided surgery with the dual labeled anti-carbonic anhydrase IX antibody preparation (111)In-DTPA-G250-IRDye800CW in mice with intraperitoneal clear cell renal cell carcinoma. BALB/c nu/nu mice with intraperitoneal SK-RC-52 lesions received 10 μg DTPA-G250-IRDye800CW labeled with 15 MBq (111)In or 10 μg of the dual labeled irrelevant control antibody NUH-82 (20 mice each). To evaluate when tumors could be detected, 4 mice per group were imaged weekly during 5 weeks with single photon emission computerized tomography/computerized tomography and the fluorescence imaging followed by ex vivo biodistribution studies. As early as 1 week after tumor cell inoculation single photon emission computerized tomography and fluorescence images showed clear delineation of intraperitoneal clear cell renal cell carcinoma with good concordance between single photon emission computerized tomography/computerized tomography and fluorescence images. The high and specific accumulation of the dual labeled antibody conjugate in tumors was confirmed in the biodistribution studies. Maximum tumor uptake was observed 1 week after inoculation (mean ± SD 58.5% ± 18.7% vs 5.6% ± 2.3% injected dose per gm for DTPA-G250-IRDye800CW vs NUH-82, respectively). High tumor uptake was also observed at other time points. This study demonstrates the feasibility of dual modality imaging with dual labeled antibody (111)In-DTPA-G250-IRDye800CW in a clear cell renal cell carcinoma model. Results indicate that preoperative and intraoperative detection of carbonic anhydrase IX expressing tumors, positive resection margins and metastasis might be feasible with this approach. Copyright © 2015 American Urological Association Education and Research

Pulse radiolysis studies of liquid heavy water at temperatures up to 250 degrees C

International Nuclear Information System (INIS)

Stuart, C.R.; Ouellette, D.C.; Elliot, A.J.

2002-09-01

This report documents the rate constants and associated activation energies for the reactions of the primary radical species, e aq - , ·OD and ·D, which are formed during the radiolysis of heavy water within the temperature range 20 to 250 o C. These heavy-water data have been compared with the corresponding information for light water. These kinetic data form part of the database that is required to model the aqueous radiation chemistry that occurs within the core of the heavy water cooled and moderated CANDU reactor. (author)

Pulse radiolysis studies of liquid heavy water at temperatures up to 250 degrees C

Energy Technology Data Exchange (ETDEWEB)

Stuart, C.R.; Ouellette, D.C.; Elliot, A.J

2002-09-01

This report documents the rate constants and associated activation energies for the reactions of the primary radical species, e{sub aq}{sup -}, {center_dot}OD and {center_dot}D, which are formed during the radiolysis of heavy water within the temperature range 20 to 250 {sup o}C. These heavy-water data have been compared with the corresponding information for light water. These kinetic data form part of the database that is required to model the aqueous radiation chemistry that occurs within the core of the heavy water cooled and moderated CANDU reactor. (author)

Cylindrical Induction Melter Modicon Control System

International Nuclear Information System (INIS)

Weeks, G.E.

1998-04-01

In the last several years an extensive R ampersand D program has been underway to develop a vitrification system to stabilize Americium (Am) and Curium (Cm) inventories at SRS. This report documents the Modicon control system designed for the 3 inch Cylindrical Induction Melter (CIM)

Analysis of large soil samples for actinides

Science.gov (United States)

Maxwell, III; Sherrod, L [Aiken, SC

2009-03-24

A method of analyzing relatively large soil samples for actinides by employing a separation process that includes cerium fluoride precipitation for removing the soil matrix and precipitates plutonium, americium, and curium with cerium and hydrofluoric acid followed by separating these actinides using chromatography cartridges.

Hadron production in 250 GeV/c π+p and K+p interactions

International Nuclear Information System (INIS)

Van Hal, P.A.

1985-01-01

Results on hadron production in π + p and K + p interactions at 250 GeV/c are presented from the experiment NA22 at the CERN SPS. With the present statistics we find: scaling in the fragmentation regions for both charged and neutral pions; a reasonable description of the K + p→π 0 /π + p→π 0 ratio by both the LUND M.C. and a DTU M.C. (Ranft and Ritter), agreement with these Monte Carlo's for the K + /π + population percentages in the forward hemisphere; no agreement for the seagull with the LUND M.C. and strong disagreement with the DTU M.C

Evaluation of the Performance of Vortex Generators on the DU 91-W2-250 Profile using Stereoscopic PIV

DEFF Research Database (Denmark)

Velte, Clara Marika; Hansen, Martin Otto Laver; Meyer, Knud Erik

2009-01-01

Stereoscopic PIV measurements investigating the effect of Vortex Generators on the lift force near stall and on glide ratio at best aerodynamic performance have been carried out in the LM Glasfiber wind tunnel on a DU 91-W2-250 profile. Measurements at two Reynolds numbers were analyzed; Re=0...

Evaluation of the Performance of Vortex Generators on the DU 91-W2-250 Profile using Stereoscopic PIV

DEFF Research Database (Denmark)

Velte, Clara Marika; Hansen, Martin Otto Laver; Meyer, Knud Erik

2008-01-01

Stereoscopic PIV measurements investigating the effect of Vortex Generators on the lift force near stall and on glide ratio at best aerodynamic performance have been carried out in the LM Glasfiber wind tunnel on a DU 91-W2-250 profile. Measurements at two Reynolds numbers were analyzed; Re=0...

A homozygous nonsense CEP250 mutation combined with a heterozygous nonsense C2orf71 mutation is associated with atypical Usher syndrome.

Science.gov (United States)

Khateb, Samer; Zelinger, Lina; Mizrahi-Meissonnier, Liliana; Ayuso, Carmen; Koenekoop, Robert K; Laxer, Uri; Gross, Menachem; Banin, Eyal; Sharon, Dror

2014-07-01

Usher syndrome (USH) is a heterogeneous group of inherited retinitis pigmentosa (RP) and sensorineural hearing loss (SNHL) caused by mutations in at least 12 genes. Our aim is to identify additional USH-related genes. Clinical examination included visual acuity test, funduscopy and electroretinography. Genetic analysis included homozygosity mapping and whole exome sequencing (WES). A combination of homozygosity mapping and WES in a large consanguineous family of Iranian Jewish origin revealed nonsense mutations in two ciliary genes: c.3289C>T (p.Q1097*) in C2orf71 and c.3463C>T (p.R1155*) in centrosome-associated protein CEP250 (C-Nap1). The latter has not been associated with any inherited disease and the c.3463C>T mutation was absent in control chromosomes. Patients who were double homozygotes had SNHL accompanied by early-onset and severe RP, while patients who were homozygous for the CEP250 mutation and carried a single mutant C2orf71 allele had SNHL with mild retinal degeneration. No ciliary structural abnormalities in the respiratory system were evident by electron microscopy analysis. CEP250 expression analysis of the mutant allele revealed the generation of a truncated protein lacking the NEK2-phosphorylation region. A homozygous nonsense CEP250 mutation, in combination with a heterozygous C2orf71 nonsense mutation, causes an atypical form of USH, characterised by early-onset SNHL and a relatively mild RP. The severe retinal involvement in the double homozygotes indicates an additive effect caused by nonsense mutations in genes encoding ciliary proteins. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Transmutation Scenarios Impacts on Advanced Nuclear Cycles. Fabrication, Reprocessing and Transportation

International Nuclear Information System (INIS)

Saturnin, A.; Sarrat, P.; Hancok, H.; Milot, J.-F.; Duret, B.; Jasserand, F.; Fillastre, E.; Giffard, F.-X.; Chabert, C.; Van Den Durpel, L.; Caron-Charles, M.; Lefevre, J.C.; Carlier, B.; Arslan, M.; Favet, D.; Garzenne, C.; Barbrault, P.

2013-01-01

Conclusions: First detailed assessment of plants and transportation in various transmutation scenarios. In case of curium transmutation: large difficulties and uncertainties requiring whole new technology development (more pronounced for ADS option). For Am transmutation: more feasible, still to be demonstrated on specific points for industrial extrapolation

Angular distributions of 250 GeV/c positive particles axially channeled in germanium crystal. Pt. 3

International Nuclear Information System (INIS)

Sun, C.R.; Gibson, W.M.; Kim, I.J.; Williams, G.O.; Carrigan, R.A. Jr.; Chrisman, B.L.; Toohig, T.E.; Guzik, Z.; Nigmanov, T.S.; Tsyganov, A.S.

1982-01-01

Channeling phenomena are observed for charged particles of momentum up to 250 GeV/c in a germanium crystal. The angular distributions of the channeled particles are compared with theoretical predictions based on a diffusion model. The results indicate additional mechanisms leading to dechanneling of the particles although channeling effects are observed for particles incident at up to several times the critical angle, in contrast with the results from low energy channeling. (orig.)

A dense grid of narrow bandpass steep edge filters for the JST/T250 telescope: summary of results

Science.gov (United States)

Brauneck, U.; Sprengard, R.; Bourquin, S.; Marín-Franch, A.

2017-09-01

On the Javalambre mountain in Spain, the Centro de Estudios de Fisica del Cosmos de Aragon (CEFCA) has setup a new wide field telescope, the JST/T250: a 2.55 m telescope with a plate scale of 22.67"/mm and a 3° diameter field of view. To conduct a photometric sky survey, a large format mosaic camera made of 14 individual CCDs is used in combination with filter trays containing 14 filters each of theses 101.7 x 96.5 mm in size. For this instrument, SCHOTT manufactured 56 specially designed steep edged bandpass interference filters which were recently completed. The filter set consists of bandpass filters in the range between 348,5 nm and 910 nm and a longpass filter at 915 nm. Most of the filters have FWHM of 14.5 nm and a blocking between 250 and 1050 nm with optical density of OD5. Absorptive color glass substrates in combination with interference filters were used to minimize residual reflection in order to avoid ghost images. Inspite of containing absorptive elements, the filters show the maximum possible transmission. This was achieved by using magnetron sputtering for the filter coating process. The most important requirement for the continuous photometric survey is the tight tolerancing of the central wavelengths and FWHM of the filters. This insures each bandpass having a defined overlap with its neighbors. In addition, the blocking of the filters is better than OD5 in the range 250-1050 nm. A high image quality required a low transmitted wavefront error (

30 CFR 250.181 - When may the Secretary cancel my lease and when am I compensated for cancellation?

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false When may the Secretary cancel my lease and when... may the Secretary cancel my lease and when am I compensated for cancellation? If the Secretary cancels.... Section 250.185 states conditions under which you will receive no compensation. The Secretary may cancel a...

Removal of actinides from high-level wastes generated in the reprocessing of commercial fuels

International Nuclear Information System (INIS)

Bond, W.D.; Leuze, R.E.

1975-09-01

Progress is reported on a technical feasibility study of removing the very long-lived actinides (uranium, neptunium, plutonium, americium, and curium) from high-level wastes generated in the commercial reprocessing of spent nuclear fuels. The study was directed primarily at wastes from the reprocessing of light water reactor (LWR) fuels and specifically to developing satisfactory methods for reducing the actinide content of these wastes to values that would make 1000-year-decayed waste comparable in radiological toxicity to natural uranium ore deposits. Although studies are not complete, results thus far indicate the most promising concept for actinide removal includes both improved recovery of actinides in conventional fuel reprocessing and secondary processing of the high-level wastes. Secondary processing will be necessary for the removal of americium and curium and perhaps some residual plutonium. Laboratory-scale studies of separations methods that appear most promising are reported and conceptual flowsheets are discussed. (U.S.)

Evidence for general instability of past climate from a 250-KYR ice-core record

DEFF Research Database (Denmark)

Johnsen, Sigfus Johann; Clausen, Henrik Brink; Dahl-Jensen, Dorthe

1993-01-01

decades. Here we present a detailed stable-isotope record for the full length of the Greenland Ice-core Project Summit ice core, extending over the past 250 kyr according to a calculated timescale. We find that climate instability was not confined to the last glaciation, but appears also to have been...... results1,2 from two ice cores drilled in central Greenland have revealed large, abrupt climate changes of at least regional extent during the late stages of the last glaciation, suggesting that climate in the North Atlantic region is able to reorganize itself rapidly, perhaps even within a few...

Determination of the sensitivity of Tc-99-NMR-measurements with a 250 MHz-spectrometer

International Nuclear Information System (INIS)

Findeisen, M.; Lorenz, B.; Wahren, M.

1990-01-01

By means of different concentrations the signal-to-noise ratios of Tc-99-NMR spectra were determined applying well measurable Tc-samples [tetrabutylammonium pertechnetate, TBA (TcO 4 )] and a 250 MHz-spectrometer. The signal-to-noise ratios of the spectra were determined by using the integrated routines of the firm's software and accumulating different number of scans. By fittings of data of the signal-to-noise ratio dependence and by extrapolation the minimum Tc-concentration could be empirically found out. Applying a duration of measurements of 12 hours about 10 -7 molar concentrations can be determined. (orig.) [de

MUSE-INGS ON AM1354-250: COLLISIONS, SHOCKS, AND RINGS

Energy Technology Data Exchange (ETDEWEB)

Conn, Blair C. [Gemini Observatory, Recinto AURA, Colina El Pino, Casilla 603, La Serena (Chile); Fogarty, L. M. R. [Sydney Institute for Astronomy, School of Physics, The University of Sydney, A28, Sydney, 2006 (Australia); Smith, Rory [Yonsei University, Graduate School of Earth System Sciences-Astronomy-Atmospheric Sciences, Yonsei-ro 50, Seoul 120-749 (Korea, Republic of); Candlish, Graeme N., E-mail: bconn@gemini.edu [Departamento de Astronomía, Universidad de Concepción, Casilla 160-C, Concepción (Chile)

2016-03-10

We present Multi Unit Spectroscopic Explorer observations of AM1354-250, confirming its status as a collisional ring galaxy that has recently undergone an interaction, creating its distinctive shape. We analyze the stellar and gaseous emission throughout the galaxy finding direct evidence that the gaseous ring is expanding with a velocity of ∼70 km s{sup −1} and that star formation is occurring primarily in H ii regions associated with the ring. This star formation activity is likely triggered by this interaction. We find evidence for several excitation mechanisms in the gas, including emission consistent with shocked gas in the expanding ring and a region of LINER-like emission in the central core of the galaxy. Evidence of kinematic disturbance in both the stars and gas, possibly also triggered by the interaction, can be seen in all of the velocity maps. The ring galaxy retains a weak spiral structure, strongly suggesting the progenitor galaxy was a massive spiral prior to the collision with its companion an estimated 140 ± 12 Myr ago.

Simulation of a 250 kW diesel fuel processor/PEM fuel cell system

Science.gov (United States)

Amphlett, J. C.; Mann, R. F.; Peppley, B. A.; Roberge, P. R.; Rodrigues, A.; Salvador, J. P.

Polymer-electrolyte membrane (PEM) fuel cell systems offer a potential power source for utility and mobile applications. Practical fuel cell systems use fuel processors for the production of hydrogen-rich gas. Liquid fuels, such as diesel or other related fuels, are attractive options as feeds to a fuel processor. The generation of hydrogen gas for fuel cells, in most cases, becomes the crucial design issue with respect to weight and volume in these applications. Furthermore, these systems will require a gas clean-up system to insure that the fuel quality meets the demands of the cell anode. The endothermic nature of the reformer will have a significant affect on the overall system efficiency. The gas clean-up system may also significantly effect the overall heat balance. To optimize the performance of this integrated system, therefore, waste heat must be used effectively. Previously, we have concentrated on catalytic methanol-steam reforming. A model of a methanol steam reformer has been previously developed and has been used as the basis for a new, higher temperature model for liquid hydrocarbon fuels. Similarly, our fuel cell evaluation program previously led to the development of a steady-state electrochemical fuel cell model (SSEM). The hydrocarbon fuel processor model and the SSEM have now been incorporated in the development of a process simulation of a 250 kW diesel-fueled reformer/fuel cell system using a process simulator. The performance of this system has been investigated for a variety of operating conditions and a preliminary assessment of thermal integration issues has been carried out. This study demonstrates the application of a process simulation model as a design analysis tool for the development of a 250 kW fuel cell system.

Interaction of nucleic acids with Coomassie Blue G-250 in the Bradford assay.

Science.gov (United States)

Wenrich, Broc R; Trumbo, Toni A

2012-09-15

The Bradford assay has been used reliably for decades to quantify protein in solution. The analyte is incubated in acidic solution of Coomassie Blue G-250 dye, during which reversible ionic and nonionic binding interactions form. Bradford assay color yields were determined for salmon, bovine, shrimp, and kiwi fruit genomic DNA; baker's yeast RNA; bovine serum albumin (BSA); and hen egg lysozyme. Pure DNA and RNA bound the dye, with color yields of 0.0017 mg⁻¹ cm⁻¹ and 0.0018 mg⁻¹ cm⁻¹, respectively. The nucleic acid-Coomassie Blue response was significant, at roughly 9% of that for BSA and 18% of that for lysozyme. Copyright © 2012 Elsevier Inc. All rights reserved.

Residual Nuclides Induced in Cu Target by a 250 MeV Proton Beam

International Nuclear Information System (INIS)

Zhang Hong-Bin; Zhang Xue-Ying; Ma Fei; Ju Yong-Qin; Ge Hong-Lin; Chen Liang; Zhang Yan-Bin; Li Yan-Yan; Luo Peng; Wang Jian-Guo; Wan Bo; Xu Xiao-Wei; Wei Ji-Fang; Zhou Bin

2015-01-01

Residual nuclide production is studied experimentally by bombarding a Cu target with a 250 MeV proton beam. The data are measured by the off-line γ-spectroscopy method. Six nuclides are identified and their cross sections are determined. The corresponding calculated results by the MCNPX and GEANT4 codes are compared with the experimental data to check the validity of the codes. A comparison shows that the MCNPX simulation has a better agreement with the experiment. The energy dependence of residual nuclide production is studied with the aid of MCNPX simulation, and it is found that the mass yields for the nuclides in the light mass region increase significantly with the proton energy. (paper)

Simulation of thermal response of the 250 MWT modular HTGR during hypothetical uncontrolled heatup accidents

International Nuclear Information System (INIS)

Harrington, R.M.; Ball, S.J.

1985-01-01

One of the central design features of the 250 MWT modular HTGR is the ability to withstand uncontrolled heatup accidents without severe consequences. This paper describes calculational studies, conducted to test this design feature. A multi-node thermal-hydraulic model of the 250 MWT modular HTGR reactor core was developed and implemented in the IBM CSMP (Continuous System Modeling Program) simulation language. Survey calculations show that the loss of forced circulation accident with loss of steam generator cooling water and with accidental depressurization is the most severe heatup accident. The peak hot-spot fuel temperature is in the neighborhood of 1600 0 C. Fuel failure and fission product releases for such accidents would be minor. Sensitivity studies show that code input assumptions for thermal properties such as the side reflector conductivity have a significant effect on the peak temperature. A computer model of the reactor vessel cavity concrete wall and its surrounding earth was developed to simulate the extremely unlikely and very slowly-developing heatup accident that would take place if the worst-case loss of forced primary coolant circulation accident were further compounded by the loss of cooling water to the reactor vessel cavity liner cooling system. Results show that the ability of the earth surrounding the cavity to act as a satisfactory long-term heat sink is very sensitive to the assumed rate of decay heat generation and on the effective thermal conductivity of the earth

Square lattice honeycomb tri-carbide fuels for 50 to 250 KN variable thrust NTP design

International Nuclear Information System (INIS)

Anghaie, Samim; Knight, Travis; Gouw, Reza; Furman, Eric

2001-01-01

Ultrahigh temperature solid solution of tri-carbide fuels are used to design an ultracompact nuclear thermal rocket generating 950 seconds of specific impulse with scalable thrust level in range of 50 to 250 kilo Newtons. Solid solutions of tri-carbide nuclear fuels such as uranium-zirconium-niobium carbide. UZrNbC, are processed to contain certain mixing ratio between uranium carbide and two stabilizing carbides. Zirconium or niobium in the tri-carbide could be replaced by tantalum or hafnium to provide higher chemical stability in hot hydrogen environment or to provide different nuclear design characteristics. Recent studies have demonstrated the chemical compatibility of tri-carbide fuels with hydrogen propellant for a few to tens of hours of operation at temperatures ranging from 2800 K to 3300 K, respectively. Fuel elements are fabricated from thin tri-carbide wafers that are grooved and locked into a square-lattice honeycomb (SLHC) shape. The hockey puck shaped SLHC fuel elements are stacked up in a grooved graphite tube to form a SLHC fuel assembly. A total of 18 fuel assemblies are arranged circumferentially to form two concentric rings of fuel assemblies with zirconium hydride filling the space between assemblies. For 50 to 250 kilo Newtons thrust operations, the reactor diameter and length including reflectors are 57 cm and 60 cm, respectively. Results of the nuclear design and thermal fluid analyses of the SLHC nuclear thermal propulsion system are presented

Optimized production and characterization of a detergent-stable protease from Lysinibacillus fusiformis C250R.

Science.gov (United States)

Mechri, Sondes; Kriaa, Mouna; Ben Elhoul Berrouina, Mouna; Omrane Benmrad, Maroua; Zaraî Jaouadi, Nadia; Rekik, Hatem; Bouacem, Khelifa; Bouanane-Darenfed, Amel; Chebbi, Alif; Sayadi, Sami; Chamkha, Mohamed; Bejar, Samir; Jaouadi, Bassem

2017-08-01

In this study, we aimed to optimize the cultural and nutritional conditions for protease production by Lysinibacillus fusiformis strain C250R in submerged fermentation process using statistical methodology. The most significant factors (gruel, wheat bran, yeast extract, and FeSO 4 ) were identified by Plackett-Burman design. Response surface methodology (RSM) was used to determine the optimum levels of the screened factors and their interaction. Under the optimized conditions, protease yield 3100U/mL was 4.5 folds higher than those obtained by the use of the initial conditions (680U/mL). Additionally, a new extracellular 51kDa-protease, designated SAPLF, was purified and biochemically characterized from strain C250R. It shows optimum activity at 70°C and pH 10. Its half-life times at 70 and 80°C were 10 and 6-h, respectively. Irreversible inhibition of enzyme activity of SAPLF with serine protease inhibitors demonstrated that it belongs to the serine protease family. Interestingly, its catalytic efficiency was higher than that of SPVP from Aeribacillus pallidus strain VP3 and Alcalase Ultra 2.5L from Bacillus licheniformis. This study demonstrated that SAPLF has a high detergent compatibility and an excellent stain removal compared to Alcalase Ultra 2.5L; which offers an interesting potential for its application in the laundry detergent industry. Copyright © 2017 Elsevier B.V. All rights reserved.

Grammaire pour adolescents 250 exercices : niveau débutant

CERN Document Server

Bié, Nathalie

2005-01-01

Ce nouveau livre d'exercices de grammaire, de la collection Le Nouvel Entraînez-vous, s'adresse à un public d'adolescents débutants et faux débutants en français langue étrangère. L'ouvrage propose 250 exercices de compréhension et de mémorisation à travers des activités de déduction et de réemploi des notions grammaticales étudiées. Le contenu des exercices est organisé autour de contextes langagiers proches de la réalité des adolescents afin de placer la communication au cœur de l'apprentissage. L'introduction des contenus grammaticaux suit la même progression que les méthodes usuelles. Chaque chapitre débute par une séquence Rappel permettant à l'apprenant de revoir rapidement les règles grammaticales développées dans les exercices. Chaque exercice est introduit par une consigne brève et concise accompagnée d'un exemple. L'ouvrage a été conçu en tenant compte des centres d'intérêts des adolescents et propose de nombreuses illustrations intégrées aux exercices. A la fin d...

Radionuclides in shallow groundwater at Solid Waste Storage Area 5 North, Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Ashwood, T.L.; Marsh, J.D. Jr.

1994-04-01

This report presents a compilation of groundwater monitoring data from Solid Waste Storage Area (SWSA) 5 North at Oak Ridge National Laboratory (ORNL) between November 1989 and September 1993. Monitoring data were collected as part of the Active Sites Environmental Monitoring Program that was implemented in 1989 in response to DOE Order 5820.2A. SWSA 5 North was established for the retrievable storage of transuranic (TRU) wastes in 1970. Four types of storage have been used within SWSA 5 North: bunkers, vaults, wells, and trenches. The fenced portion of SWSA 5 North covers about 3.7 ha (9 acres) in the White Oak Creek watershed south of ORNL. The area is bounded by White Oak Creek and two ephemeral tributaries of White Oak Creek. Since 1989, groundwater has been monitored in wells around SWSA 5 North. During that time, elevated gross alpha contamination (reaching as high as 210 Bq/L) has consistently been detected in well 516. This well is adjacent to burial trenches in the southwest corner of the area. Water level measurements in wells 516 and 518 suggest that water periodically inundates the bottom of some of those trenches. Virtually all of the gross alpha contamination is generated by Curium 244 and Americium 241. A special geochemical investigation of well 516 suggests that nearly all of the Curium 44 and Americium 241 is dissolved or associated with dissolved organic matter. These are being transported at the rate of about 2 m/year from the burial trenches, through well 516, to White Oak Creek, where Curium 244 has been detected in a few bank seeps. Concentrations at these seeps are near detection levels (<1 Bq/L)

Radionuclides in shallow groundwater at Solid Waste Storage Area 5 North, Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Ashwood, T.L.; Marsh, J.D. Jr.

1994-04-01

This report presents a compilation of groundwater monitoring data from Solid Waste Storage Area (SWSA) 5 North at Oak Ridge National Laboratory (ORNL) between November 1989 and September 1993. Monitoring data were collected as part of the Active Sites Environmental Monitoring Program that was implemented in 1989 in response to DOE Order 5820.2A. SWSA 5 North was established for the retrievable storage of transuranic (TRU) wastes in 1970. Four types of storage have been used within SWSA 5 North: bunkers, vaults, wells, and trenches. The fenced portion of SWSA 5 North covers about 3.7 ha (9 acres) in the White Oak Creek watershed south of ORNL. The area is bounded by White Oak Creek and two ephemeral tributaries of White Oak Creek. Since 1989, groundwater has been monitored in wells around SWSA 5 North. During that time, elevated gross alpha contamination (reaching as high as 210 Bq/L) has consistently been detected in well 516. This well is adjacent to burial trenches in the southwest corner of the area. Water level measurements in wells 516 and 518 suggest that water periodically inundates the bottom of some of those trenches. Virtually all of the gross alpha contamination is generated by Curium 244 and Americium 241. A special geochemical investigation of well 516 suggests that nearly all of the Curium 44 and Americium 241 is dissolved or associated with dissolved organic matter. These are being transported at the rate of about 2 m/year from the burial trenches, through well 516, to White Oak Creek, where Curium 244 has been detected in a few bank seeps. Concentrations at these seeps are near detection levels (<1 Bq/L).

Studies on Corrosion of Annealed and Aged 18 Ni 250 Grade Maraging Steel in Sulphuric Acid Medium

OpenAIRE

Poornima, T.; Jagannatha, Nayak; Shetty, A. Nityananda

2010-01-01

The corrosion behavior of aged and annealed sample of 18 Ni 250 grade maraging steel was investigated in varied conditions of concentration and temperature of sulphuric acid medium, using electrochemical techniques like Tafel polarization and electrochemical impedance spectroscopy (EIS). The results obtained from both the techniques are in good agreement. These results have shown increase in corrosion rate of aged specimen with increase in concentration and temperature of sulphuric acid. With...

Analysis of RF section of 250 kW CW C-Band high power klystron

International Nuclear Information System (INIS)

Badola, Richa; Kaushik, Meenu; Baloda, Suman; Kirti; Vrati; Lamba, O.S.; Joshi, L.M.

2012-01-01

Klystron is a microwave tube which is used as a power amplifier in various applications like radar, particle accelerators and thermonuclear reactors. The paper deals with the analysis of RF section of 250 kW CW C band high power klystron for 50 to 60 kV beam voltage The simulation is done using Poisson's superfish and AJ disk software's Design of cavity is done using superfish. The result of superfish is used to decide the dimensions of the geometry of the cavity and AJ disk is used to determined the centre to centre distances between the cavities in order to obtain the desired powers. (author)

Temperature dependence of the surface energy of mercury from 0 to 250 deg. C

CERN Document Server

Halas, S

2002-01-01

The surface energy (SE) for mercury was calculated on the basis of the free electron model in which the electron density parameter, r sub s , for bulk electrons was calculated from the density of mercury while the electron density parameter for surface electrons, r sub s sub s , was assumed to be higher by a factor that is linearly dependent on temperature. Ideal agreement of calculated SE values with experimental data was attained for the temperatures 0-250 deg. C assuming that r sub s sub s = r sub s x 1.0021 sup T sup / sup 1 sup 0 sup 0 deg. C. (letter to the editor)

Cardiac ultrastructural changes in rats following 250 Gy whole body. gamma. -irradiation

Energy Technology Data Exchange (ETDEWEB)

Yao, Guo; Mingyue, Zhu; Zhiqin, Zhao

1985-10-01

Sixteen rats were whole body irradiated with 250 Gy of /sup 60/Co ..gamma..-rays, killed at different intervals after exposure, and then observed by electron microscope. We found lysis of part of myofilaments in specimen obtained at 10 minutes after exposure, and resolution of Z-band at 30 minutes after exposure. These changes were more significant in sections at 12 hours postirradiation, but there also appeared cell regeneration at the same time. The vascular changes were more obvious with the endothelial cytoplasma projected in capillary lumen, nearly obstructing it. All of above described changes may be found in hematologic or intestinal forms of radiation sickness, but they must take place more late after exposure. In cardiovascular form, however, these changes were found as early as 10-30 minutes after exposure; this is a special feature helpful to diagnosis.

Hydrothermal syntheses, structural, Raman, and luminescence studies of Cm[M(CN)2]3.3H2O and Pr[M(CN)2]3.3H2O (M=Ag, Au)

International Nuclear Information System (INIS)

Assefa, Zerihun; Haire, Richard G.; Sykora, Richard E.

2008-01-01

We have prepared Cm[Au(CN) 2 ] 3 .3H 2 O and Cm[Ag(CN) 2 ] 3 .3H 2 O as a part of our continuing investigations into the chemistry of the 5f-elements' dicyanometallates. Single crystals of Cm[Au(CN) 2 ] 3 .3H 2 O were obtained from the reaction of CmCl 3 and KAu(CN) 2 under mild hydrothermal conditions. Due to similarities in size, the related praseodymium compounds were also synthesized and characterized for comparison with the actinide systems. The compounds crystallize in the hexagonal space group P6 3 /mcm, where the curium and the transition metals interconnect through cyanide bridging. Crystallographic data (Mo Kα, λ=0.71073 A): Cm[Au(CN) 2 ] 3 .3H 2 O (1), a=6.6614(5) A, c=18.3135(13) A, V=703.77(9), Z=2; Pr[Au(CN) 2 ] 3 .3H 2 O (3), a=6.6662(8) A, c=18.497(3) A, V=711.83(17), Z=2; Pr[Ag(CN) 2 ] 3 .3H 2 O (4), a=6.7186(8) A, c=18.678(2) A, V=730.18(14), Z=2. The Cm 3+ and/or Pr 3+ ions are coordinated to six N-bound CN - groups resulting in a trigonal prismatic arrangement. Three oxygen atoms of coordinated water molecules tricap the trigonal prismatic arrangement providing a coordination number of nine for the f-elements. The curium ions in both compounds exhibit a strong red emission corresponding to the 6 D 7/2 → 8 S 7/2 transition. This transition is observed at 16,780 cm -1 , with shoulders at 17,080 and 16,840 cm -1 for the Ag complex, while the emission is red shifted by ∼100 cm -1 in the corresponding gold complex. The Pr systems also provide well-resolved emissions upon f-f excitation. - Graphical abstract: Coordination polymeric compounds between a trans-plutonium element, curium and transition metal ions, gold(I) and silver(I), were prepared using the hydrothermal synthetic procedure. The curium ion and the transition metals are interconnected through cyanide bridging. The Cm ion has a tricapped trigonal prismatic coordination environment with coordination number of nine. Detail photoluminescence studies of the complexes are also reported

HIC1 interacts with a specific subunit of SWI/SNF complexes, ARID1A/BAF250A

International Nuclear Information System (INIS)

Van Rechem, Capucine; Boulay, Gaylor; Leprince, Dominique

2009-01-01

HIC1, a tumor suppressor gene epigenetically silenced in many human cancers encodes a transcriptional repressor involved in regulatory loops modulating p53-dependent and E2F1-dependent cell survival and stress responses. HIC1 is also implicated in growth control since it recruits BRG1, one of the two alternative ATPases (BRM or BRG1) of SWI/SNF chromatin-remodeling complexes to repress transcription of E2F1 in quiescent fibroblasts. Here, through yeast two-hybrid screening, we identify ARID1A/BAF250A, as a new HIC1 partner. ARID1A/BAF250A is one of the two mutually exclusive ARID1-containing subunits of SWI/SNF complexes which define subsets of complexes endowed with anti-proliferative properties. Co-immunoprecipitation assays in WI38 fibroblasts and in BRG1-/- SW13 cells showed that endogenous HIC1 and ARID1A proteins interact in a BRG1-dependent manner. Furthermore, we demonstrate that HIC1 does not interact with BRM. Finally, sequential chromatin immunoprecipitation (ChIP-reChIP) experiments demonstrated that HIC1 represses E2F1 through the recruitment of anti-proliferative SWI/SNF complexes containing ARID1A.

Apparent Affinity Estimates and Reversal of the Effects of Synthetic Cannabinoids AM-2201, CP-47,497, JWH-122, and JWH-250 by Rimonabant in Rhesus Monkeys.

Science.gov (United States)

Hruba, Lenka; McMahon, Lance R

2017-08-01

Synthetic cannabinoids have been prohibited due to abuse liability and toxicity. Four such synthetic cannabinoids, AM-2201 ([1-(5-fluoropentyl)indol-3-yl]-naphthalen-1-ylmethanone), CP-47,497 (2-[(1R,3S)-3-hydroxycyclohexyl]-5-(2-methyloctan-2-yl)phenol), JWH-122 [(4-methylnaphthalen-1-yl)-(1-pentylindol-3-yl)methanone], and JWH-250 [2-(2-methoxyphenyl)-1-(1-pentylindol-3-yl)ethanone], were tested for their capacity to produce CB 1 receptor-mediated discriminative stimulus effects in two groups of rhesus monkeys. One group ( n = 4) discriminated Δ 9 -tetrahydrocannabinol (∆ 9 -THC; 0.1 mg/kg i.v.), and a second group ( n = 4) discriminated the cannabinoid antagonist rimonabant (1 mg/kg i.v.) while receiving 1 mg/kg/12 hours of ∆ 9 -THC. AM-2201, JWH-122, CP-47,497, JWH-250, and ∆ 9 -THC increased ∆ 9 -THC lever responding. Duration of action was 1-2 hours for AM-2201, JWH-122, and JWH-250 and 4-5 hours for CP-47,497 and ∆ 9 -THC. Rimonabant (1 mg/kg) surmountably antagonized the discriminative stimulus effects of all cannabinoid agonists; the magnitude of rightward shift was 10.6-fold for AM-2201, 10.7-fold for JWH-122, 11.0-fold for CP-47,497, and 15.7-fold for JWH-250. The respective pK B values were not significantly different: 6.61, 6.65, 6.66, and 6.83. In ∆ 9 -THC-treated monkeys discriminating rimonabant, AM-2201 (0.1 and 0.32 mg/kg), JWH-122 (0.32 and 1 mg/kg), JWH-250 (1 and 3.2 mg/kg), and CP-47,497 (0.32, 1, and 3.2 mg/kg) produced not only rate-decreasing effects that were reversed by rimonabant, but also dose-dependent, rightward shifts in the rimonabant discrimination dose-effect function. These results show striking similarity in the CB 1 receptor mechanism mediating the subjective effects of AM-2201, JWH-122, JWH-250, and CP-47,497. For products containing AM-2201 and JWH-122, a short duration of action could lead to more frequent use; moreover, inattention to differences in potency among synthetic cannabinoids could underlie unexpected

Inclusive production of π0 mesons in π+p-,K+p- and pp interactions at 250 GeV/c

International Nuclear Information System (INIS)

Adamus, M.A.; Azhinenko, I.V.

1986-01-01

Data on inclusive π 0 production in the forward hemisphere at Feynman variable (x > 0.025) in the center-of-inertia system in π + p, K + p, and pp interactions at 250 GeV/c are presented. These data are compared to the data at lower energies and interpreted in terms of quark-parton models

1:250,000-scale Hydrologic Units of the United States

Science.gov (United States)

Steeves, Peter; Nebert, Douglas

1994-01-01

The Geographic Information Retrieval and Analysis System (GIRAS) was developed in the mid 70s to put into digital form a numberof data layers which were of interest to the USGS. One of these data layers was the Hydrologic Units. The map is based on the Hydrologic Unit Maps published by the U.S. Geological Survey Office of Water Data Coordination, together with the list descriptions and name of region, subregion, accounting units, and cataloging unit. The hydrologic units are encoded with an eight-digit number that indicates the hydrologic region (first two digits), hydrologic subregion (second two digits), accounting unit (third two digits), and cataloging unit (fourth two digits). The data produced by GIRAS was originally collected at a scale of 1:250K. Some areas, notably major cities in the west, were recompiled at a scale of 1:100K. In order to join the data together and use the data in a geographic information system (GIS) the data were processed in the ARC/INFO GUS software package. Within the GIS, the data were edgematched and the neatline boundaries between maps were removed to create a single data set for the conterminous

Coulomb sums for 7Li nucleus at 3-momentum transfers q=1,250...1,625 fm-1

International Nuclear Information System (INIS)

Buki, A.Yu.; Shevchenko, N.G.; Timchenko, I.S.

2009-01-01

The experimental response functions of 7 Li nucleus at effective 3-momentum transfers q = 1.250; 1.375; 1.500 and 1.625 fm -1 are presented. The longitudinal response functions were used to evaluate the Coulomb sum values. The Coulomb sums for 6 Li obtained by us earlier were applied to analyze these data. The Coulomb sums of lithium isotopes were compared with the well-known Coulomb sums values of the other nuclei

INACTIVATION OF MS2 VIRUS IN DRINKING WATER: ATLANTIC ULTRAVIOLET CORPORATION MEGATRON UNIT, MODEL M250 AT CHULA VISTA, CALIFORNIA

Science.gov (United States)

Verification testing of the Atlantic Ultraviolet Megatron M250 system was conducted over a 48-day period from 11/01/01 to 12/18/01. The feedwater to the ultraviolet (UV) unit during the testing was effluent from the Otay Water Treatment Plant (OWTP), a conventional plant with fl...

[Clinical development of acute noise-induced acoustic trauma. An evaluation of a study of 250 cases].

Science.gov (United States)

Suc, B; Poulet, M; Asperge, A; Vix, J; Barberot, J P; Doucet, F

1994-01-01

Traumatic damage on Cochlea (250 cases) induced by assault gun (F.A.M.A.S.) consists in tinitus and hearing impairement on 6000 Hz. Noise's effects are specific to one Cochlea. Dissociated developments of both tinitus and hearing loss show that their anatomical sites are different. Acoustic injury entails definitive haire cells lesions, cellular biochemical and vascular changes. The treatment that reestablishes or raises cochlear blood flow entails recovery in 80% of cases provided that it is given within 48 hours after the trauma.

Cobalt and molybdenum activated electrodes in foam based alkaline electrolysis cells at 150-250 °C and 40 bar

DEFF Research Database (Denmark)

Allebrod, Frank; Chatzichristodoulou, Christodoulos; Mogensen, Mogens Bjerg

2014-01-01

A new type of alkaline electrolysis cells with nickel foam based gas diffusion electrodes and KOH (aq) immobilized in mesoporous SrTiO3 has been developed and tested at temperatures of 150 C, 200 C and 250 C at a pressure of 40 bar. Two cells have been characterized during the 270 h long test...

Pre- and post-irradiation properties of copper alloys at 250 deg. C following bonding and bakeout thermal cycles

International Nuclear Information System (INIS)

Singh, B.N.; Edwards, D.J.; Eldrup, M.; Toft, P.

1997-01-01

Screening experiments were carried out to investigate the effect of bonding and bakeout thermal cycles on microstructure, mechanical properties and electrical resistivity of the oxide dispersion strengthened (GlidCop, CuAl-25) and the precipitation hardened (CuCrZr, CuNiBe) copper alloys. Tensile specimens of CuCrZr and CuNiBe alloys were given various heat treatments corresponding to solution anneal, prime-ageing, and bonding thermal treatment followed by re-ageing and the reactor bakeout treatment at 350 deg. C for 100 h. Tensile specimens of CuAl-25 were given the heat treatment corresponding to the bonding thermal cycle. A number of heat treated specimens were neuron irradiated at 250 deg. C to a dose level of ∼ 0.3 dpa in the DR-3 reactor at Risoe. Both unirradiated and irradiated specimens with various heat treatments were tensile tested at 250 deg. C. The microstructure and electrical resistivity of these specimens were determined in the unirradiated as well as irradiated conditions. The post-deformation microstructure of the irradiated specimens was also investigated. The fracture surfaces of both unirradiated and irradiated specimens were examined. Results of these investigations are reported in the present report. The main effect of the bonding thermal cycle heat treatment was a slight decrease in strength of CuCrZr and CuNiBe alloys. The strength of CuAl-25, on the other hand, remained almost unaltered. The post irradiation tests at 250 deg. C showed a severe loss of ductility in the case of CuNiBe alloy. The irradiated CuAl-25 and CuCrZr specimens, on the other hand, exhibited a reasonable amount of uniform elongation. The results are briefly discussed in terms of thermal and irradiation stability of precipitates and particles and irradiation-induced segregation, precipitation and recovery of dislocation microstructure. (au) 7 tabs., 28 ills., 15 refs

A 250-GHz CARM [Cyclotron Auto Resonance Maser] oscillator experiment driven by an induction linac

International Nuclear Information System (INIS)

Caplan, M.; Kulke, B.; Bubp, D.G.; McDermott, D.; Luhmann, N.

1990-01-01

A 250-GHz Cyclotron Auto Resonance Maser (CARM) oscillator has been designed and constructed and will be tested using a 1-kA, 2-MeV electron beam produced by the induction linac at the Accelerator Research Center (ARC) facility of Lawrence Livermore National Laboratory (LLNL). The oscillator circuit was made to operate in the TE 11 mode at ten times cutoff using waveguide Bragg reflectors to create an external cavity Q of 8000. Theory predicts cavity fill times of less than 30 ns (pulse length) and efficiencies approaching 20% is sufficiently low transverse electron velocity spreads are maintained (2%)

Design of an induction linac driven CARM [Cyclotron Auto Resonance Maser] oscillator at 250 GHz

International Nuclear Information System (INIS)

Caplan, M.; Kulke, B.

1990-01-01

We present the design of a 250 GHz, 400 MW Cyclotron Auto Resonance Maser (CARM) oscillator driven by a 1 KA, 2 MeV electron beam produced by the induction linac at the ARC facility of LLNL. The oscillator circuit is designed as a feedback amplifier operating in the TE 11 mode at ten times cutoff terminated at each end with Bragg reflectors. Theory and cold test results are in good agreement for a manufactured Bragg reflector using 50 μm corrugations to ensure mode purity. The CARM is to be operational by February 1990. 3 figs., 2 tabs

Alkaline electrolysis cell at high temperature and pressure of 250 °C and 42 bar

DEFF Research Database (Denmark)

Allebrod, Frank; Chatzichristodoulou, Christodoulos; Mogensen, Mogens Bjerg

2013-01-01

A new type of alkaline electrolysis cells with nickel foam based gas diffusion electrodes and KOH (aq) immobilized in mesoporous SrTiO3 has been developed and tested at temperatures and pressures up to 250 °C and 42 bar, respectively. Current densities of 1.0 A cm−2 have been measured at a cell v...... voltage of 1.5 V without the use of expensive noble metal catalysts. High electrical efficiency and current density combined with relatively small production costs may lead to both reduced investment and operating costs for hydrogen and oxygen production....

Pierce-Wiggler electron beam system for 250 GHz GYRO-BWO: Final report

International Nuclear Information System (INIS)

Pirkle, D.R.; Alford, C.W.; Anderson, M.H.; Garcia, R.F.; Legarra, J.R.; Nordquist, A.L.

1989-01-01

This final report summarizes the design and performance of the VUW-8028 Pierce-Wiggler electron beam systems, which can be used to power high frequency gyro-BWO's. The operator's manual for this gyro-BWO beamstick is included as appendix A. Researchers at Lawrence Livermore National Laboratory (LLNL) are developing a gyro-BWO with a center frequency of 250 GHz, 6% bandwidth, and 10 kV peak output power. The gyro-BWO will be used to drive a free electron laser amplifier at LLNL. The electron beam requirements of the gyro-BWO application are: Small beam size, .100 inch at 2500 gauss axial magnetic field; a large fraction of the electron energy in rotational velocity; ability to vary the electrons' axial velocity easily, for electronic tuning; and low velocity spread i.e. little variation in the axial velocities of the electrons in the interaction region. 1 ref., 13 figs

A single CD4 test with 250 cells/mm3 threshold predicts viral suppression in HIV-infected adults failing first-line therapy by clinical criteria.

Directory of Open Access Journals (Sweden)

Charles F Gilks

Full Text Available In low-income countries, viral load (VL monitoring of antiretroviral therapy (ART is rarely available in the public sector for HIV-infected adults or children. Using clinical failure alone to identify first-line ART failure and trigger regimen switch may result in unnecessary use of costly second-line therapy. Our objective was to identify CD4 threshold values to confirm clinically-determined ART failure when VL is unavailable.3316 HIV-infected Ugandan/Zimbabwean adults were randomised to first-line ART with Clinically-Driven (CDM, CD4s measured but blinded or routine Laboratory and Clinical Monitoring (LCM, 12-weekly CD4s in the DART trial. CD4 at switch and ART failure criteria (new/recurrent WHO 4, single/multiple WHO 3 event; LCM: CD4<100 cells/mm(3 were reviewed in 361 LCM, 314 CDM participants who switched over median 5 years follow-up. Retrospective VLs were available in 368 (55% participants.Overall, 265/361 (73% LCM participants failed with CD4<100 cells/mm(3; only 7 (2% switched with CD4≥250 cells/mm(3, four switches triggered by WHO events. Without CD4 monitoring, 207/314 (66% CDM participants failed with WHO 4 events, and 77(25%/30(10% with single/multiple WHO 3 events. Failure/switching with single WHO 3 events was more likely with CD4≥250 cells/mm(3 (28/77; 36% (p = 0.0002. CD4 monitoring reduced switching with viral suppression: 23/187 (12% LCM versus 49/181 (27% CDM had VL<400 copies/ml at failure/switch (p<0.0001. Amongst CDM participants with CD4<250 cells/mm(3 only 11/133 (8% had VL<400 copies/ml, compared with 38/48 (79% with CD4≥250 cells/mm(3 (p<0.0001.Multiple, but not single, WHO 3 events predicted first-line ART failure. A CD4 threshold 'tiebreaker' of ≥250 cells/mm(3 for clinically-monitored patients failing first-line could identify ∼80% with VL<400 copies/ml, who are unlikely to benefit from second-line. Targeting CD4s to single WHO stage 3 'clinical failures' would particularly avoid premature, costly

Downscaling 250-m MODIS growing season NDVI based on multiple-date landsat images and data mining approaches

Science.gov (United States)

Gu, Yingxin; Wylie, Bruce K.

2015-01-01

The satellite-derived growing season time-integrated Normalized Difference Vegetation Index (GSN) has been used as a proxy for vegetation biomass productivity. The 250-m GSN data estimated from the Moderate Resolution Imaging Spectroradiometer (MODIS) sensors have been used for terrestrial ecosystem modeling and monitoring. High temporal resolution with a wide range of wavelengths make the MODIS land surface products robust and reliable. The long-term 30-m Landsat data provide spatial detailed information for characterizing human-scale processes and have been used for land cover and land change studies. The main goal of this study is to combine 250-m MODIS GSN and 30-m Landsat observations to generate a quality-improved high spatial resolution (30-m) GSN database. A rule-based piecewise regression GSN model based on MODIS and Landsat data was developed. Results show a strong correlation between predicted GSN and actual GSN (r = 0.97, average error = 0.026). The most important Landsat variables in the GSN model are Normalized Difference Vegetation Indices (NDVIs) in May and August. The derived MODIS-Landsat-based 30-m GSN map provides biophysical information for moderate-scale ecological features. This multiple sensor study retains the detailed seasonal dynamic information captured by MODIS and leverages the high-resolution information from Landsat, which will be useful for regional ecosystem studies.

The Undergraduate ALFALFA Team: Outcomes for Over 250 Undergraduate Participants

Science.gov (United States)

Troischt, Parker; Koopmann, Rebecca A.; Haynes, Martha P.; ALFALFA Team

2016-01-01

The NSF-sponsored Undergraduate ALFALFA (Arecibo Legacy Fast ALFA) Team (UAT) is a consortium of 19 institutions founded to promote undergraduate research and faculty development within the extragalactic ALFALFA HI blind survey project and follow-up programs. In this talk we present outcomes for the more than 250 undergraduate students who have who have participated in the program during the 8 years of funding. 40% of these students have been women and members of underrepresented groups. To date 148 undergraduate students have attended annual workshops at Arecibo Observatory, interacting with faculty, graduate students, their peers, and Arecibo staff in lectures, group activities, tours, and observing runs. Team faculty have supervised 159 summer research projects and 120 academic year (e.g., senior thesis) projects. 68 students have traveled to Arecibo Observatory for observing runs and 55 have presented their results at national meetings such as the AAS. Through participation in the UAT, students are made aware of career paths they may not have previously considered. More than 90% of alumni are attending graduate school and/or pursuing a career in STEM. 42% of those pursuing graduate degrees in Physics or Astronomy are women. This work has been supported by NSF grants AST-0724918/0902211, AST-075267/0903394, AST-0725380, and AST-1211005

The Enduring Legacy of 250 Years of Pharmacology in Edinburgh.

Science.gov (United States)

Kelly, John S; Mackay, Angus V P

2018-01-06

In 1768, 250 years ago, the University of Edinburgh appointed Francis Home to the first chair of materia medica, the accumulated knowledge of materials used in healing. Francis Home and his colleagues were determined to improve the quality of medical training in Edinburgh by introducing a final examination and compiling a catalog of medicines validated by the Royal College of Physicians of Edinburgh. The catalog, known as the Edinburgh Pharmacopoeia, was a great success, partly due to the orderly nature of its contents, its routine editing to eliminate worthless entries, and the introduction of new treatments whose preparation was precisely documented. In a relatively short time, the worth of the Edinburgh Pharmacopoeia was recognized throughout Europe, America, and the British Empire. Today, the British and European Pharmacopoeias are catalogs of publicly available, legally enforceable standards for active pharmaceutical ingredients and finished dosage forms of pharmaceutical products and medical devices. Home and the many luminaries who succeeded him would surely take pleasure and pride in the fact that the mantra of today's medicines regulators worldwide is little different from that of these early visionaries: "To take better advantage of the best possible science in the service of the public health and our health-care systems" ( 1 , p. 492).

Transuranium analysis methodologies for biological and environmental samples

International Nuclear Information System (INIS)

Wessman, R.A.; Lee, K.D.; Curry, B.; Leventhal, L.

1978-01-01

Analytical procedures for the most abundant transuranium nuclides in the environment (i.e., plutonium and, to a lesser extent, americium) are available. There is a lack of procedures for doing sequential analysis for Np, Pu, Am, and Cm in environmental samples, primarily because of current emphasis on Pu and Am. Reprocessing requirements and waste disposal connected with the fuel cycle indicate that neptunium and curium must be considered in environmental radioactive assessments. Therefore it was necessary to develop procedures that determine all four of these radionuclides in the environment. The state of the art of transuranium analysis methodology as applied to environmental samples is discussed relative to different sample sources, such as soil, vegetation, air, water, and animals. Isotope-dilution analysis with 243 Am ( 239 Np) and 236 Pu or 242 Pu radionuclide tracers is used. Americium and curium are analyzed as a group, with 243 Am as the tracer. Sequential extraction procedures employing bis(2-ethyl-hexyl)orthophosphoric acid (HDEHP) were found to result in lower yields and higher Am--Cm fractionation than ion-exchange methods

Multiple recycling of plutonium in advanced PWRs

International Nuclear Information System (INIS)

Kloosterman, J.L.

1998-04-01

The influence of the moderator-to-fuel ratio in MOX fueled PWRs on the moderator void coefficient, the fuel temperature coefficient, the moderator temperature coefficient, the boron reactivity worth, the critical boron concentration, the mean neutron generation time and the effective delayed neutron fraction has been assessed. Increasing the moderator-to-fuel ratio to values larger than three, gives a moderator void coefficient sufficiently large to recycle the plutonium at least four times. Scenario studies show that four times recycling of plutonium in PWRs reduces the plutonium mass produced with a factor of three compared with a reference once-through reactor park, but that the americium and curium production triple. If the minor actinides and the remaining plutonium after four times recycling are disposed of, the reduction of the radiotoxicity reaches only a factor of two. This factor increases to five at the maximum when the plutonium is further recycled. Recycling of americium and curium is needed to further reduce the radiotoxicity of the spent fuel. 4 refs

Universal description of inelastic and non(single)-diffractive multiplicity distributions in pp collisions at 250, 360 and 800 GeV/c

International Nuclear Information System (INIS)

Krasznovszky, S.; Wagner, I.

1987-06-01

A distribution function is proposed for multiplicity in accordance with the stochastic number evolution. This function gives a universal description of inelastic and nondiffractive multiplicity distributions in pp collisions at 250, 360 and 800 GeV/c. The negative binomial distribution fails in the description of inelastic data. (author)

Pairwise comparison of 89Zr- and 124I-labeled cG250 based on positron emission tomography imaging and nonlinear immunokinetic modeling: in vivo carbonic anhydrase IX receptor binding and internalization in mouse xenografts of clear-cell renal cell carcinoma

International Nuclear Information System (INIS)

Cheal, Sarah M.; Punzalan, Blesida; Doran, Michael G.; Osborne, Joseph R.; Evans, Michael J.; Lewis, Jason S.; Zanzonico, Pat; Larson, Steven M.

2014-01-01

The PET tracer, 124 I-cG250, directed against carbonic anhydrase IX (CAIX) shows promise for presurgical diagnosis of clear-cell renal cell carcinoma (ccRCC) (Divgi et al. in Lancet Oncol 8:304-310, 2007; Divgi et al. in J Clin Oncol 31:187-194, 2013). The radiometal 89 Zr, however, may offer advantages as a surrogate PET nuclide over 124 I in terms of greater tumor uptake and retention (Rice et al. in Semin Nucl Med 41:265-282, 2011). We have developed a nonlinear immunokinetic model to facilitate a quantitative comparison of absolute uptake and antibody turnover between 124 I-cG250 and 89 Zr-cG250 using a human ccRCC xenograft tumor model in mice. We believe that this unique model better relates quantitative imaging data to the salient biological features of tumor antibody-antigen binding and turnover. We conducted experiments with 89 Zr-cG250 and 124 I-cG250 using a human ccRCC cell line (SK-RC-38) to characterize the binding affinity and internalization kinetics of the two tracers in vitro. Serial PET imaging was performed in mice bearing subcutaneous ccRCC tumors to simultaneously detect and quantify time-dependent tumor uptake in vivo. Using the known specific activities of the two tracers, the equilibrium rates of antibody internalization and turnover in the tumors were derived from the PET images using nonlinear compartmental modeling. The two tracers demonstrated virtually identical tumor cell binding and internalization but showed markedly different retentions in vitro. Superior PET images were obtained using 89 Zr-cG250, owing to the more prolonged trapping of the radiolabel in the tumor and simultaneous washout from normal tissues. Estimates of cG250/CAIX complex turnover were 1.35 - 5.51 x 10 12 molecules per hour per gram of tumor (20 % of receptors internalized per hour), and the ratio of 124 I/ 89 Zr atoms released per unit time by tumor was 17.5. Pairwise evaluation of 89 Zr-cG250 and 124 I-cG250 provided the basis for a nonlinear immunokinetic

Desarrollo de la formulación de cefalexina 250 mg granulado para suspensión oral

Directory of Open Access Journals (Sweden)

Roxana Martínez Fernández

2002-04-01

Full Text Available Se desarrolló la formulación de la cefalexina 250 mg como granulado para suspensión oral. Se utilizó la vía húmeda para la preparación del granulado, teniendo en cuenta los resultados de la caracterización físico-química realizada a las materias primas empleadas. Los resultados de los análisis físico-químicos y microbiológicos del producto terminado fueron satisfactorios. Se realizó un estudio de estabilidad en vida de estante durante 18 meses, con el que se pudo comprobar que la formulación obtenida es estable durante el tiempo estudiado a temperatura entre 15 y 25 °C y durante 7 d después de reconstituido y mantenido en refrigeración. El medicamento cumple con las especificaciones de calidad descritas en la USP 24.The formulation of cephalexin 250 mg was developed as a granulate for oral suspension. The humid way was used for the preparation of the granulate, taking into account the results of the physicochemical characterization of the raw materials used. The results of the physicochemical and microbiological analyses of the finished product were satisfactory. A shelf life stability study was conducted for 18 months that made possible to prove that the formulation obtained was stable during the studied time at temperatures between 15 and 25 ºC and for 7 days after being reconstituted and kept in refrigeration. The drug meets the quality specifications described in the USP 24.

41 CFR 102-34.250 - Do Federal employees in Government motor vehicles have to use all safety devices and follow all...

Science.gov (United States)

2010-07-01

... safety devices and follow all safety guidelines? Yes, Federal employees in Government motor vehicles have... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Do Federal employees in Government motor vehicles have to use all safety devices and follow all safety guidelines? 102-34.250 Section...

Energy investments needs are estimated to $250 milliards, 1995-2010, in the South and East Mediterranean countries

International Nuclear Information System (INIS)

Calvet, B.

1996-01-01

The energy consumption knows a sharper increase in the North and in the East of the Mediterranean sea than in European Union. These trends should continue during the two next decades. From now until 2010, according to the companies predictions, the energy consumption of the free trade future zone countries should continue to strongly increase, to reach near 2 000 millions of petroleum equivalent tons. Then, the financing needs should reach some $250 milliards according to an inquiry of the Energy Mediterranean Observatory. (N.C.)

Actinides compounds for the transmutation: scientific contributions of american and japanese collaborations; Composes d'actinides pour la transmutation: apports scientifiques de collaborations americaines et japonaises

Energy Technology Data Exchange (ETDEWEB)

Raison, Ph.; Albiot, T

2000-07-01

This paper deals with the minor actinides transmutation and the scientific contribution of the ORNL and the JAERI. It presents researches on the Am-Zr-Y-O system in the framework of the heterogeneous reprocessing, the curium and pyrochlore structures, with the ORNL contribution and phase diagrams, data of Thermodynamics, actinides nitrides, with the JAERI. (A.L.B.)

Actinides compounds for the transmutation: scientific contributions of american and japanese collaborations

International Nuclear Information System (INIS)

Raison, Ph.; Albiot, T.

2000-01-01

This paper deals with the minor actinides transmutation and the scientific contribution of the ORNL and the JAERI. It presents researches on the Am-Zr-Y-O system in the framework of the heterogeneous reprocessing, the curium and pyrochlore structures, with the ORNL contribution and phase diagrams, data of Thermodynamics, actinides nitrides, with the JAERI. (A.L.B.)

Historical review of californium-252 discovery and development

International Nuclear Information System (INIS)

Stoddard, D.H.

1985-01-01

This paper discusses the discovery and history of californium 252. This isotope may be synthesized by irradiating plutonium 239, plutonium 242, americium 243, or curium 244 with neutrons in a nuclear reactor. Various experiments and inventions involving 252 Cf conducted at the Savannah River Plant are discussed. The evolution of radiotherapy using californium 252 is reviewed

Neutron resonance parameters of CM isotopes

International Nuclear Information System (INIS)

Belanova, T.S.; Kolesov, A.G.; Poruchikov, V.A.

1977-01-01

The total neutron cross sections of isotopes 244, 245, 246, 248 Curium have been measured on reactor CM-2 using the time-of-flight method. Single-level Breit-Wigner resonance parameters: energy E 0 , neutron width 2g GITAn, total width GITA, total neutron cross section in resonance sigma 0 have been obtained by the shape and area methods

Interaction of europium and curium with alpha-amylase

Energy Technology Data Exchange (ETDEWEB)

Barkleit, Astrid [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Chemistry of the F-Elements; Heller, Anne [Technische Univ. Dresden (Germany). Inst. for Zoology, Molecular Cell Physiology and Endocrinology; Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Biogeochemistry

2016-07-01

Time-resolved laser-induced fluorescence spectroscopy (TRLFS) revealed that Eu(III) and Cm(III) form two dominant species with the protein α-amylase (Amy): one with the coordination of a single carboxylate group of the protein and the other with three coordinating carboxylate groups.

Actinide production from xenon bombardments of curium-248

International Nuclear Information System (INIS)

Welch, R.B.

1985-01-01

Production cross sections for many actinide nuclides formed in the reaction of 129 Xe and 132 Xe with 248 Cm at bombarding energies slightly above the coulomb barrier were determined using radiochemical techniques to isolate these products. These results are compared with cross sections from a 136 Xe + 248 Cm reaction at a similar energy. When compared to the reaction with 136 Xe, the maxima in the production cross section distributions from the more neutron deficient projectiles are shifted to smaller mass numbers, and the total cross section increases for the production of elements with atomic numbers greater than that of the target, and decreases for lighter elements. These results can be explained by use of a potential energy surface (PES) which illustrates the effect of the available energy on the transfer of nucleons and describes the evolution of the di-nuclear complex, an essential feature of deep-inelastic reactions (DIR), during the interaction. The other principal reaction mechanism is the quasi-elastic transfer (QE). Analysis of data from a similar set of reactions, 129 Xe, 132 Xe, and 136 Xe with 197 Au, aids in explaining the features of the Xe + Cm product distributions, which are additionally affected by the depletion of actinide product yields due to deexcitation by fission. The PES is shown to be a useful tool to predict the general features of product distributions from heavy ion reactions

All that's mine I carry with me. Early life disease and adult health in Sweden during 250 years

OpenAIRE

Lindström, Martin

2015-01-01

The aim of this thesis is to study early life risk exposures in relation to adult health and mortality in Sweden during 250 years. A number of causal mechanisms by which exposure to diseases and stressful economic and social conditions early in life may lead to increased morbidity and mortality later in life are discussed (paper I). The early life exposures investigated are the foetal origins (nutrition) and the inflammation hypotheses. Longitudinal demographic and socioeconomic data for indi...

SU-E-T-359: Emulation of Yb-169 Gamma-Ray Spectrum Using Metal-Filtered 250 KVp X-Rays for Pre-Clinical Studies of Gold Nanoparticle-Aided Radiation Therapy

International Nuclear Information System (INIS)

Reynoso, F; Cho, S

2015-01-01

Purpose: To develop an external beam surrogate of the Yb-169 brachytherapy source applying a filter-based spectrum modulation technique to 250 kVp x-rays. In-vitro/vivo studies performed with the modulated 250 kVp beam will help gauge the benefits of implementing gold nanoparticle-aided radiotherapy with the Yb-169 source. Methods: A previously validated MCNP5 model of the Phillips RT-250 orthovoltage unit was used to obtain the percentage depth dose (PDD) and filtered photon spectra for a variety of filtration and irradiation conditions. Photon spectra were obtained using the average flux F4 tally in air right after all collimation. A 30 x 30 x 30 cm 3 water phantom was used to compute the PDD along the central axis (CAX) under the standards conditions of a 10 x 10 cm 2 field size at 50 cm SSD. Cylindrical cells of 4 cm in diameter and the energy deposition F6 tally were used along the CAX to score the doses down to 20 cm depth. The number of particle history was set to 2 x 10 8 in order to keep the relative uncertainty within each cell < 0.3%. The secondary electron spectrum within a gold-loaded tissue due to each photon spectrum was also calculated using EGSnrc and compared with that due to Yb-169 gamma rays. Results: Under the practical constraints for the spectrum modulation task, 250 kVp x-rays filtered by a 0.25 mm Erbium (Er) foil produced the best match with Yb-169 gamma rays, in terms of PDD and, more importantly, secondary electron spectrum. Conclusion: Modulation of 250kVp x-ray spectrum by an Er-filter was found effective in emulating the gamma ray spectrum of Yb-169. Possible benefits as predicted from the current MC model such as enhanced radiosensitization with the Er-filtered beam (as a surrogate of Yb-169) was confirmed with a separate in-vitro study. Supported by DOD/PCRP grant W81XWH-12-1-0198

Complete Set of Deuteron Analyzing Powers for dp Elastic Scattering at 250 MeV/nucleon and Three Nucleon Forces

Directory of Open Access Journals (Sweden)

Shimizu Y.

2010-04-01

Full Text Available Measurements of a complete set of deuteron analyzing powers (iT11, T20, T21, T22 for elastic deuteron–proton scattering at 250 MeV/nucleon have been performed with polarized deuteron beams at RIKEN RI Beam Factory. The obtained data are compared with the Faddeev calculations based on the modern nucleon–nucleon forces together with the Tucson-Melbourne’99, and UrbanaIX three nucleon forces.

Bioequivalence of 250 mg lysine clonixinate tablets after a single oral dose in a healthy female Mexican population under fasting conditions.

Science.gov (United States)

Marcelín-Jiménez, G; Angeles, A C P; García, A; Morales, M; Rivera, L; Martín-Del-Campo, A

2010-05-01

To evaluate the bioequivalence between two 250 mg-tablets of lysine clonixinate, Dorixina Forte (Siegfried Rhein, México) as reference product, and Prestodol (Farmaceúticos Rayere, S.A., México) as test formulation. 26 healthy adult female Mexican volunteers received a single oral dose of 250-mg lysine clonixinate under fasting conditions. The drug was administered following a randomized, two-period, two-sequence, cross-over design. Twelve serial blood samples were collected up to 8 h after dosing, and clonixin (CLX) was measured by ultra-performance liquid chromatography (UPLC) coupled with tandem mass spectrometry. Decimal logarithm values of Cmax and area under the curve (AUC) were used to construct a classic confidence interval at 90% (90% CI). Bioequivalence was established if 90% CI of mean ratios (test/reference) fall within the 0.8-1.25 range. Volunteers formed a homogeneous population in terms of age (27.2 +/- 6.3 years), weight (55.9 +/- 6.5 kg), height (1.6 +/- 0.04 m), and body mass index (BMI) (22.91 +/- 2.03 kg/m(2)). Reference formulation exhibited the following pharmacokinetics: C(max) (32.39 +/- 8.32 microg/ml); t(max) (0.64 +/- 0.2 h); AUC0-8h (48.92 +/- 16.51 microg x h/ml); t1/2 (1.3 +/- 0.24 h); CLapp (5.64 +/- 1.99 l/h), and Vdapp (10.22 +/- 2.9 l). Concerning bioequivalence, 90% CI were: C(max) (82.32 - 98.79), AUC0-t (94.59-106.29), and AUC(0-inf) (94.61-106.42), with a statistical power of > 0.90 at every tested interval. This single-dose study found that both 250-mg immediate-release tablets of lysine clonixinate met the Mexican regulatory criteria for bioequivalence in these volunteers.

Soil and Terrain Database for Upper Tana River Catchment (version 1.1) - scale 1:250,000 (SOTER_UT_v1.1)

NARCIS (Netherlands)

Dijkshoorn, J.A.; Macharia, P.; Kempen, B.

2014-01-01

The Soil and Terrain database for the Upper Tana River Catchment (version 1.1) (SOTER_UT_v1.1) at scale 1:250,000 was compiled to support the Green Water Credits (GWC) programme by creating a primary SOTER dataset for a hydrology assessment of the basin. The Kenya Soil Survey of the Kenya

Neutral strange particle production in π+/K+p interactions at 250 GeV/c

International Nuclear Information System (INIS)

Scholten, A.J.

1988-01-01

This thesis in which a detailed study of K n inclusive production in K + p and π + p interactions at 250 GeV/c is presented, concentrates on neutral strange interaction products and draws some conclusions about the fate of the strange quark. In ch. 2 the experimental setup is described and in ch. 3 the series of computer programs that perform data reduction. Ch. 4 deals with the selectionn of events and neutral kaons. Also the calculations needed to correct for losses and background are described there. In ch. 5 inclusive and semi-inclusive distributions are presented and compared to data obtained in experiments at lower beam energy. In ch. 6 the data are compared with model predictions. In ch. 7 the main conclusions are summarized. (H.W.). 64 refs.; 39 refs.; 19 tabs

Electrical properties of pseudo-single-crystalline Ge films grown by Au-induced layer exchange crystallization at 250 °C

Science.gov (United States)

Higashi, H.; Kudo, K.; Yamamoto, K.; Yamada, S.; Kanashima, T.; Tsunoda, I.; Nakashima, H.; Hamaya, K.

2018-06-01

We study the electrical properties of pseudo-single-crystalline Ge (PSC-Ge) films grown by a Au-induced layer exchange crystallization method at 250 °C. By inserting the SiNx layer between PSC-Ge and SiO2, we initiatively suppress the influence of the Ge/SiO2 interfacial defective layers, which have been reported in our previous works, on the electrical properties of the PSC-Ge layers. As a result, we can detect the influence of the ionized Au+ donors on the temperature-dependent hole concentration and Hall mobility. To further examine their electrical properties in detail, we also fabricate p-thin-film transistors (TFTs) with the PSC-Ge layer. Although the off-state leakage currents are suppressed by inserting the SiNx layer, the value of on/off ratio remains poor (leakage current although a nominal field effect mobility is enhanced up to ˜25 cm2/V s. Considering these features, we conclude that the Au contaminations into the PSC-Ge layer can affect the electrical properties and device performances despite a low-growth temperature of 250 °C. To achieve further high-performance p-TFTs, we have to suppress the Au contaminations into PSC-Ge during the Au-induced crystallization growth.

Thermal power calibration of the TRIGA Mark I IPR-R1 reactor during the upgrading tests to 250 kW

International Nuclear Information System (INIS)

Mesquita, Amir Zacarias; Maretti, Fausto Junior; Rezende, Hugo Cesar

2002-01-01

This paper presents the results and the methodology used to calibrate the thermal power of the TRIGA MARK I IPR-R1 Reactor in CDTN, Belo Horizonte, Brazil. This calibration was realized during the operation tests carried out to allow the reactor power upgrade from the current 100 kW to 250 kW. The methodology consisted in the measurement of the inlet and outlet temperature and the water flow in the primary cooling loop. The thermal balance together with the thermal losses gave the thermal power. There were made three sequences of tests. The first rising of the thermal power was made with the usual configuration of the core (59 fuel elements). After the changing of the ion chambers position and the control rod and the increase of the number of fuels (63 fuel elements), a new evaluation of the thermal power was accomplished, having been obtained a thermal power of 234 kW, for an indication of 250 kW in the lineal channel. After the return of the core to the initial configuration (59 fuel elements), it took place a new test, getting back the reactor to the power level of 100 kW. (author)

Pairwise comparison of {sup 89}Zr- and {sup 124}I-labeled cG250 based on positron emission tomography imaging and nonlinear immunokinetic modeling: in vivo carbonic anhydrase IX receptor binding and internalization in mouse xenografts of clear-cell renal cell carcinoma

Energy Technology Data Exchange (ETDEWEB)

Cheal, Sarah M.; Punzalan, Blesida; Doran, Michael G.; Osborne, Joseph R. [Memorial Sloan-Kettering Cancer Center, Department of Radiology, New York, NY (United States); Evans, Michael J. [Memorial Sloan-Kettering Cancer Center, Human Oncology and Pathogenesis Program, New York, NY (United States); Lewis, Jason S. [Memorial Sloan-Kettering Cancer Center, Department of Radiology, New York, NY (United States); Memorial Sloan-Kettering Cancer Center, Program in Molecular Pharmacology and Chemistry, New York, NY (United States); Memorial Sloan-Kettering Cancer Center, Radiochemistry and Imaging Sciences Service, New York, NY (United States); Zanzonico, Pat [Memorial Sloan-Kettering Cancer Center, Department of Radiology, New York, NY (United States); Memorial Sloan-Kettering Cancer Center, Molecular Pharmacology and Therapy Service, New York, NY (United States); Memorial-Sloan Kettering Cancer Center, New York, NY (United States); Larson, Steven M. [Memorial Sloan-Kettering Cancer Center, Department of Radiology, New York, NY (United States); Memorial Sloan-Kettering Cancer Center, Program in Molecular Pharmacology and Chemistry, New York, NY (United States); Memorial Sloan-Kettering Cancer Center, Molecular Pharmacology and Therapy Service, New York, NY (United States)

2014-05-15

The PET tracer, {sup 124}I-cG250, directed against carbonic anhydrase IX (CAIX) shows promise for presurgical diagnosis of clear-cell renal cell carcinoma (ccRCC) (Divgi et al. in Lancet Oncol 8:304-310, 2007; Divgi et al. in J Clin Oncol 31:187-194, 2013). The radiometal {sup 89}Zr, however, may offer advantages as a surrogate PET nuclide over {sup 124}I in terms of greater tumor uptake and retention (Rice et al. in Semin Nucl Med 41:265-282, 2011). We have developed a nonlinear immunokinetic model to facilitate a quantitative comparison of absolute uptake and antibody turnover between {sup 124}I-cG250 and {sup 89}Zr-cG250 using a human ccRCC xenograft tumor model in mice. We believe that this unique model better relates quantitative imaging data to the salient biological features of tumor antibody-antigen binding and turnover. We conducted experiments with {sup 89}Zr-cG250 and {sup 124}I-cG250 using a human ccRCC cell line (SK-RC-38) to characterize the binding affinity and internalization kinetics of the two tracers in vitro. Serial PET imaging was performed in mice bearing subcutaneous ccRCC tumors to simultaneously detect and quantify time-dependent tumor uptake in vivo. Using the known specific activities of the two tracers, the equilibrium rates of antibody internalization and turnover in the tumors were derived from the PET images using nonlinear compartmental modeling. The two tracers demonstrated virtually identical tumor cell binding and internalization but showed markedly different retentions in vitro. Superior PET images were obtained using {sup 89}Zr-cG250, owing to the more prolonged trapping of the radiolabel in the tumor and simultaneous washout from normal tissues. Estimates of cG250/CAIX complex turnover were 1.35 - 5.51 x 10{sup 12} molecules per hour per gram of tumor (20 % of receptors internalized per hour), and the ratio of {sup 124}I/{sup 89}Zr atoms released per unit time by tumor was 17.5. Pairwise evaluation of {sup 89}Zr-cG250 and {sup

Large self-affine fractality in $\\pi^{+}p$ and $K^{+}p$ collisions at 250 GeV/c

CERN Document Server

Agababian, N M

1996-01-01

Taking into account the anisotropy of phase space in multiparticle production, a self-affine analysis of factorial moments was carried out on the NA22 data for $\\pi^{+}p$ and $K^{+}p$ collisions at 250 GeV/$c$. Within the transverse plane, the Hurst exponents measuring the anisotropy are consistent with unit value (i.e. no anisotropy). They are, however, only half that value when the longitudinal direction is compared to the transverse ones. Fractality, indeed, turns out to be self-affine rather than self-similar in multiparticle production. In three-dimensional phase space, power-law scaling is observed to be better realized in self-affine than in self-similar analysis.

Tensile behavior of EUROFER ODS steel after neutron irradiation up to 16.3 dpa between 250 and 450 °C

International Nuclear Information System (INIS)

Materna-Morris, Edeltraud; Lindau, Rainer; Schneider, Hans-Christian; Möslang, Anton

2015-01-01

Highlights: • The first 9%CrWVTa steel (0.5% Y_2O_3), EUROFER ODS HIP, have been neutron irradiated up to 16.3 dpa, between 250 and 450 °C, in the High Flux Reactor (HFR). • After post-irradiation tensile tests, there was not any increase of the upper yield strength or strain localization after irradiation which is typical of RAFM steels. • Initially higher yield strength, R_p_0_._2, and distinctive tensile strength, R_m, of EUROFER ODS HIP compared to EUROFER97 steel. • These values increased due to the neutron irradiation at lower irradiation temperatures. - Abstract: During the development of structural material for future fusion reactors, a 50 kg heat of reduced-activation ferritic-martensitic 9%CrWVTa steel with nanoscaled Y_2O_3-particles, EUROFER97 ODS HIP, was produced using powder metallurgy fabrication technology. This first batch of EUROFER97 ODS HIP and, for comparison, the steel EUROFER97 were prepared for a post-irradiation tensile test program. During neutron irradiation in the HFR (High Flux Reactor, The Netherlands), an accumulated dose of up to 16.3 dpa was reached for 771 days at full power, with the irradiation temperature ranging between 250 and 450 °C. During the post-examinations, all specimens showed the highest tensile strength at lower irradiation temperatures between 250 and 350 °C. However, ODS-alloy and steel were found to clearly differ in the mechanical behavior, which could be documented by fully instrumented tensile tests. In the un-irradiated state, tensile strength of the ODS-alloy already was increased considerably by about 60% compared to the steel. Strengthening was further increased by another 20% after neutron irradiation, but with a much better ductility than observed in the steel. The typical irradiation-induced strain localization of EUROFER97 or RAFM steels could not be observed in the EUROFER97 ODS HIP alloy.

Fuel selection for radioisotope thermoelectric generators

International Nuclear Information System (INIS)

Menezes, A.

1988-06-01

The availability of Radioisotope Thermoeletric Generator fuels is evaluated based on the amount of fuel discharged from selected power reactors. In general, the best alternatives are either to use Plutonium-238 produced by irradiation of Neptunium-237 generated in typical thermal reactors or to use Curium-244 directly separated from the discharged fuels of fast or thermal reactors. (author) [pt

Laboratory calibration of the calcium carbonate clumped isotope thermometer in the 25-250 °C temperature range

Science.gov (United States)

Kluge, Tobias; John, Cédric M.; Jourdan, Anne-Lise; Davis, Simon; Crawshaw, John

2015-05-01

Many fields of Earth sciences benefit from the knowledge of mineral formation temperatures. For example, carbonates are extensively used for reconstruction of the Earth's past climatic variations by determining ocean, lake, and soil paleotemperatures. Furthermore, diagenetic minerals and their formation or alteration temperature may provide information about the burial history of important geological units and can have practical applications, for instance, for reconstructing the geochemical and thermal histories of hydrocarbon reservoirs. Carbonate clumped isotope thermometry is a relatively new technique that can provide the formation temperature of carbonate minerals without requiring a priori knowledge of the isotopic composition of the initial solution. It is based on the temperature-dependent abundance of the rare 13C-18O bonds in carbonate minerals, specified as a Δ47 value. The clumped isotope thermometer has been calibrated experimentally from 1 °C to 70 °C. However, higher temperatures that are relevant to geological processes have so far not been directly calibrated in the laboratory. In order to close this calibration gap and to provide a robust basis for the application of clumped isotopes to high-temperature geological processes we precipitated CaCO3 (mainly calcite) in the laboratory between 23 and 250 °C. We used two different precipitation techniques: first, minerals were precipitated from a CaCO3 supersaturated solution at atmospheric pressure (23-91 °C), and, second, from a solution resulting from the mixing of CaCl2 and NaHCO3 in a pressurized reaction vessel at a pressure of up to 80 bar (25-250 °C).

Molecular hydrogen in the z = 2.811 absorbing material toward the quasar PKS 0528-250

International Nuclear Information System (INIS)

Levshakov, S.A.; Varshalovich, D.A.

1985-01-01

Among the previously unidentified absorbtion features in the spectrum of the quasar PKS 0528-250 obtained by previous authors tentative evidence has been found for H 2 lines at the same redshift (z = 2.811) as that of the well-known absorption-line system. The column density of molecules has been estimated from the curve of growth; the fraction of H 2 appears to be about 2 x 10 -5 . The ortho- to para-H 2 ratio corresponds to the excitation temperature of Tsub(ex)(H 2 ) = 300 +- 150 K, though the upper rotational levels J >= 3 turn out be overpopulated. The results obtained seem to provide substantial evidence for the existence of molecular hydrogen at the early cosmological epoch with z approx. 3. (author)

A functional proteogenomic analysis of endometrioid and clear cell carcinomas using reverse phase protein array and mutation analysis: protein expression is histotype-specific and loss of ARID1A/BAF250a is associated with AKT phosphorylation

International Nuclear Information System (INIS)

Wiegand, Kimberly C; Lu, Yiling; Zhang, Fan; Anglesio, Michael S; Gilks, Blake; Mills, Gordon B; Huntsman, David G; Carey, Mark S; Hennessy, Bryan T; Leung, Samuel; Wang, Yemin; Ju, Zhenlin; McGahren, Mollianne; Kalloger, Steve E; Finlayson, Sarah; Stemke-Hale, Katherine

2014-01-01

Ovarian cancer is now recognized as a number of distinct diseases primarily defined by histological subtype. Both clear cell ovarian carcinomas (CCC) and ovarian endometrioid carcinomas (EC) may arise from endometriosis and frequently harbor mutations in the ARID1A tumor suppressor gene. We studied the influence of histological subtype on protein expression with reverse phase protein array (RPPA) and assessed proteomic changes associated with ARID1A mutation/BAF250a expression in EC and CCC. Immunohistochemistry (IHC) for BAF250a expression was performed on 127 chemotherapy-naive ovarian carcinomas (33 CCC, 29 EC, and 65 high-grade serous ovarian carcinomas (HGSC)). Whole tumor lysates were prepared from frozen banked tumor samples and profiled by RPPA using 116 antibodies. ARID1A mutations were identified by exome sequencing, and PIK3CA mutations were characterized by MALDI-TOF mass spectrometry. SAM (Significance Analysis of Microarrays) was performed to determine differential protein expression by histological subtype and ARID1A mutation status. Multivariate logistic regression was used to assess the impact of ARID1A mutation status/BAF250a expression on AKT phosphorylation (pAKT). PIK3CA mutation type and PTEN expression were included in the model. BAF250a knockdown was performed in 3 clear cell lines using siRNA to ARID1A. Marked differences in protein expression were observed that are driven by histotype. Compared to HGSC, SAM identified over 50 proteins that are differentially expressed in CCC and EC. These included PI3K/AKT pathway proteins, those regulating the cell cycle, apoptosis, transcription, and other signaling pathways including steroid hormone signaling. Multivariate models showed that tumors with loss of BAF250a expression showed significantly higher levels of AKT-Thr 308 and AKT-Ser 473 phosphorylation (p < 0.05). In 31 CCC cases, pAKT was similarly significantly increased in tumors with BAF250a loss on IHC. Knockdown of BAF250a by siRNA in

Relative bioavailability of generic and branded 250-mg and 500-mg oral chlorphenesin carbamate tablets in healthy Korean volunteers: a single-dose, randomized-sequence, open-label, two-period crossover trial.

Science.gov (United States)

Yu, Ji-young; Song, Hyun Ho; Kim, Bo Gyeom; Park, Hyeon Ju; Choi, Kwang Sik; Kwon, Young Ee

2009-11-01

Chlorphenesin carbamate is a skeletal muscle relaxant approved in Korea for use in the treatment of pain and discomfort related to skeletal muscle trauma and inflammation. The aim of this study was to assess the bioequivalence of a generic formulation of chlorphenesin carbamate at doses of 250 and 500 mg and 2 branded formulations of the same doses in healthy Korean adults. This single-dose, randomized-sequence, open-label, 2-period crossover study was conducted in healthy Korean male and female volunteers. Subjects were assigned to receive, in a randomized sequence, a single dose of the generic (test) and branded (reference) formulations of chlorphenesin carbamate at a dose of 250 or 500 mg. Blood samples were drawn at 0, 0.33, 0.67, 1, 1.5, 2, 3, 4, 6, 9, 12, and 15 hours after administration. Pharmacokinetic properties (C(max), T(max), AUC(0-t) AUC(0-infinity), t(1/2), and ke) were determined using HPLC. The formulations were to be considered bioequivalent if the 90% CIs of the treatment ratios of the geometric means of C(max) and AUC(0-t) were within a predetermined range of log 0.80 to log 1.25 based on regulatory criteria. Tolerability was assessed by monitoring for adverse events (AEs) on physical examination and/or e-mail and personal interview at the beginning and end of each study period. Twenty-eight subjects (22 men, 6 women) received chlorphenesin carbamate at the 250-mg dose, and 24 male subjects received the 500-mg dose. The mean (SD) ages of the subjects were 24.0 (2.6) and 24.0 (1.9) years in the 250- and 500-mg groups, respectively. No significant differences were found between the test and reference formulations (90% CIs: C(max), 1.0048-1.1153 with the 250-mg dose and 0.9630-1.1189 with the 500-mg dose; AUC(0-t), 0.9882-1.0546 and 0.9842-1.0578, respectively). No clinically significant AEs (upper gastric pain, abdominal bloating, pyrexia, edema, nausea, heartburn, constipation, headache, dizziness, drowsiness, or fatigue) were reported throughout

Self-affine scaling from non-integer phase-space partition in $\\pi^{+}p$ and $K^{+}p$ collisions at 250 GeV/$c$

CERN Document Server

Agababian, N M

1998-01-01

A factorial-moment analysis with real (integer and non-integer) phase space partition is applied to $\\pi^+$p and K$^+$p collisions at 250 GeV/$c$. Clear evidence is shown for self-affine rather than self-similar power-law scaling in multiparticle production. The three-dimensional self-affine second-order scaling exponent is determined to be 0.061$\\pm$0.010.

A Versatile High Speed 250 MHz Pulse Imager for Biomedical Applications

Science.gov (United States)

Epel, Boris; Sundramoorthy, Subramanian V.; Mailer, Colin; Halpern, Howard J.

2009-01-01

A versatile 250 MHz pulse electron paramagnetic resonance (EPR) instrument for imaging of small animals is presented. Flexible design of the imager hardware and software makes it possible to use virtually any pulse EPR imaging modality. A fast pulse generation and data acquisition system based on general purpose PCI boards performs measurements with minimal additional delays. Careful design of receiver protection circuitry allowed us to achieve very high sensitivity of the instrument. In this article we demonstrate the ability of the instrument to obtain three dimensional images using the electron spin echo (ESE) and single point imaging (SPI) methods. In a phantom that contains a 1 mM solution of narrow line (16 μT, peak-to-peak) paramagnetic spin probe we achieved an acquisition time of 32 seconds per image with a fast 3D ESE imaging protocol. Using an 18 minute 3D phase relaxation (T2e) ESE imaging protocol in a homogeneous sample a spatial resolution of 1.4 mm and a standard deviation of T2e of 8.5% were achieved. When applied to in vivo imaging this precision of T2e determination would be equivalent to 2 torr resolution of oxygen partial pressure in animal tissues. PMID:19924261

Customized broadband Sloan-filters for the JST/T250 and JAST/T80 telescopes: measurement summary

Science.gov (United States)

Brauneck, Ulf; Sprengard, Ruediger; Bourquin, Sebastien; Marín-Franch, Antonio

2018-01-01

The Centro de Estudios de Fisica del Cosmos de Aragon will conduct a photometric sky survey with two new telescopes recently set up on the Javalambre mountain in Spain: the JST/T250 is a 2.55-m telescope with a plate scale of 22.67 arc⁢sec/mm and a 3-deg-diameter field of view (FoV) and the auxiliary telescope JAST/T80 with a 82-cm primary mirror and an FoV of 2 deg diameter. A multiple CCD (9k-by-9k array size, 10-μm pixel size) mosaic camera is used in combination with filter trays or filter wheels, each containing a multitude of filters in dimensions of 101.7×96.5 mm or 106.8×106.8 mm. For this project, Schott manufactured 56 specially designed narrow band steep-edged bandpass interference filters and five broadband Sloan-filters which were completed only recently. We report here on the results of the broadband Sloan-filters with transmission bands of 324 to 400 nm (Sloan-u), 400 to 550 nm (Sloan-g), 550 to 700 nm (Sloan-r), 695 to 850 nm (Sloan-i), and 830 to 1200 nm (Sloan-z). The filters are composed of Schott filterglasses and clearglass substrates coated with interference filters and represent an improvement of broadband Sloan filters commonly used in astronomy. In spite of the absorptive elements, the filters show maximum possible transmissions achieved by magnetron sputtered filter coatings. In addition, the blocking of the filters is better than OD5 (transmission <10 to -5) in the range 250 to 1050 nm which was achieved by combining up to three substrates. A high image quality required a low transmitted wavefront error (<λ/8 locally, respectively <λ/2 globally). We report on the spectral and interferometric results measured on the filters.

Changes of regional climate variability in central Europe during the past 250 years

Science.gov (United States)

Böhm, R.

2012-05-01

The paper uses the data potential of very long and homogenized instrumental climate time series in the south central Europe for analyzing one feature which is very dominant in the climate change debate --whether anthropogenic climate warming causes or goes along with an increase of climate extremes. The monthly resolved data of the HISTALP data collection provide 58 single series for the three climate elements, air pressure, air temperature and precipitation, that start earlier than 1831 and extend back to 1760 in some cases. Trends and long-term low frequent climate evolution is only shortly touched in the paper. The main goal is the analysis of trends or changes of high frequent interannual and interseasonal variability. In other words, it is features like extremely hot summers, very cold winters, excessively dry or wet seasons which the study aims at. The methods used are based on detrended highpass series whose variance is analyzed in discrete 30-year windows moving over the entire instrumental period. The analysis of discrete subintervals relies on the unique number of 8 (for precipitation 7) such "normal periods". The second approach is based on the same subintervals though not in fixed but moving windows over the entire instrumental period. The first result of the study is the clear evidence that there has been no increase of variability during the past 250 years in the region. The second finding is similar but concentrates on the recent three decades which are of particular interest because they are the first 30 years with dominating anthropogenic greenhouse gas forcing. We can show that also this recent anthropogenic normal period shows no widening of the PDF (probability density function) compared to the preceding ones. The third finding is based on the moving window technique. It shows that interannual variability changes show a clear centennial oscillating structure for all three climate elements in the region. For the time being we have no explanation

Magnetoresistance properties of Fe0,2C0,8 composite materials pre and post gamma irradiated at 250 kGy dose

International Nuclear Information System (INIS)

Yunasfi; Setyo Purwanto; Wisnu A A

2009-01-01

Research about change of, magnetoresistance properties of Fe 0,2 C 0,8 composite materials pre and post gamma irradiation at a dose of 250 kGy was carried out. Fe 0,2 C 0,8 was prepared by mixing of Fe and C powder with the ratio of Fe : C set on 20:80 in weight %. In this research, the phase structure and magnetic properties of Fe 0,2 C 0,8 composite materials after 250 KGy dose of gamma irradiation have been measured and analyzed. The phase structure of Fe 0,2 C 0,8 was analyzed using X-ray diffractometer (XRD), whole the magnetoresistance properties was characterized using Four Point Probe method. The analyzing results showed the decreasing of X-ray diffraction peak intensity, but also in the same time showed the increasing of magnetoresistance properties after gamma irradiation. The enhancement of magnetoresistance value reached 5 times at 7,5 kOe magnetic field. This enhancement was caused due to structure defect within Fe 0,2 C 0,8 composite initiated by interaction between radiation of gamma ray and composite materials that further causes a change of magnetic interaction intensity in this materials. (author)

Tensile behavior of RAFM alloys after neutron irradiation of up to 16.3 dpa between 250 and 450 °C

International Nuclear Information System (INIS)

Materna-Morris, E.; Schneider, H.-C.; Möslang, A.

2014-01-01

Tensile specimen of steel EUROFER97 and other alloys on the basis of RAFM steels such, as OPTIFER and F82H alloys, and Ga3X were irradiated and post-examined during a neutron irradiation program of up to 16.3 dpa between 250 and 450 °C in the HFR (High Flux Reactor) in the Netherlands. These tensile results were compared with former irradiation programs, with lower neutron doses of up to 0.8 and 2.4 dpa to quantify the difference in tensile strengthening. The average increase of tensile strength was in a range of 300 MPa between 0.8 and 16.3 dpa at temperatures of 250–300 °C. This behavior can be correlated with irradiation-induced changes in the microstructure. Most of the hardening can be attributed to dislocation loops, point defects or small precipitates as observed in boron-free alloys as F82H mod. and EUROFER97. Whereas the hardening in boron-containing alloys OPTIFER alloys and Ga3X can be correlated in addition with the combination of helium bubbles. At the highest irradiation and test temperature at 450 °C, all tensile data of all investigated materials were in the range of those of non-irradiated and irradiated material due to thermal aging effects

Tensile behavior of RAFM alloys after neutron irradiation of up to 16.3 dpa between 250 and 450 °C

Energy Technology Data Exchange (ETDEWEB)

Materna-Morris, E., E-mail: edeltraud.materna-morris@kit.edu; Schneider, H.-C., E-mail: hans-christian.schneider@kit.edu; Möslang, A., E-mail: anton.moeslang@kit.edu

2014-12-15

Tensile specimen of steel EUROFER97 and other alloys on the basis of RAFM steels such, as OPTIFER and F82H alloys, and Ga3X were irradiated and post-examined during a neutron irradiation program of up to 16.3 dpa between 250 and 450 °C in the HFR (High Flux Reactor) in the Netherlands. These tensile results were compared with former irradiation programs, with lower neutron doses of up to 0.8 and 2.4 dpa to quantify the difference in tensile strengthening. The average increase of tensile strength was in a range of 300 MPa between 0.8 and 16.3 dpa at temperatures of 250–300 °C. This behavior can be correlated with irradiation-induced changes in the microstructure. Most of the hardening can be attributed to dislocation loops, point defects or small precipitates as observed in boron-free alloys as F82H mod. and EUROFER97. Whereas the hardening in boron-containing alloys OPTIFER alloys and Ga3X can be correlated in addition with the combination of helium bubbles. At the highest irradiation and test temperature at 450 °C, all tensile data of all investigated materials were in the range of those of non-irradiated and irradiated material due to thermal aging effects.

Rapid column extraction method for actinides and strontium in fish and other animal tissue samples

International Nuclear Information System (INIS)

Maxwell III, S.L.; Faison, D.M.

2008-01-01

The analysis of actinides and radiostrontium in animal tissue samples is very important for environmental monitoring. There is a need to measure actinide isotopes and strontium with very low detection limits in animal tissue samples, including fish, deer, hogs, beef and shellfish. A new, rapid separation method has been developed that allows the measurement of plutonium, neptunium, uranium, americium, curium and strontium isotopes in large animal tissue samples (100-200 g) with high chemical recoveries and effective removal of matrix interferences. This method uses stacked TEVA Resin R , TRU Resin R and DGA Resin R cartridges from Eichrom Technologies (Darien, IL, USA) that allows the rapid separation of plutonium (Pu), neptunium (Np), uranium (U), americium (Am), and curium (Cm) using a single multi-stage column combined with alphaspectrometry. Strontium is collected on Sr Resin R from Eichrom Technologies (Darien, IL, USA). After acid digestion and furnace heating of the animal tissue samples, the actinides and 89/90 Sr are separated using column extraction chromatography. This method has been shown to be effective over a wide range of animal tissue matrices. Vacuum box cartridge technology with rapid flow rates is used to minimize sample preparation time. (author)

Determining the dissolution rates of actinide glasses: A time and temperature Product Consistency Test study

International Nuclear Information System (INIS)

Daniel, W.E.; Best, D.R.

1995-01-01

Vitrification has been identified as one potential option for the e materials such as Americium (Am), Curium (Cm), Neptunium (Np), and Plutonium (Pu). A process is being developed at the Savannah River Site to safely vitrify all of the highly radioactive Am/Cm material and a portion of the fissile (Pu) actinide materials stored on site. Vitrification of the Am/Cm will allow the material to be transported and easily stored at the Oak Ridge National Laboratory. The Am/Cm glass has been specifically designed to be (1) highly durable in aqueous environments and (2) selectively attacked by nitric acid to allow recovery of the valuable Am and Cm isotopes. A similar glass composition will allow for safe storage of surplus plutonium. This paper will address the composition, relative durability, and dissolution rate characteristics of the actinide glass, Loeffler Target, that will be used in the Americium/Curium Vitrification Project at Westinghouse Savannah River Company near Aiken, South Carolina. The first part discusses the tests performed on the Loeffler Target Glass concerning instantaneous dissolution rates. The second part presents information concerning pseudo-activation energy for the one week glass dissolution process

Crystal structures of iron bearing tetrahedrite and tennantite at 25 and 250 degrees C by means of Rietveld refinement of synchrotron data

DEFF Research Database (Denmark)

Friese, K.; Grzechnik, A.; Makovicky, E.

2008-01-01

Rietveld refinement of X-ray synchrotron data was performed for two synthetic tetrahedrite samples, with 0.61 and 1.83 Fe atoms, and two synthetic tennantite samples with 0.10 and 1.23 Fe atoms p.f.u. M-12(Sb,As)(4)S-13. Measurements were performed at 25 and 250 degrees C. For both the phases...

Crop Dominance Mapping with IRS-P6 and MODIS 250-m Time Series Data

Directory of Open Access Journals (Sweden)

Murali Krishna Gumma

2014-04-01

Full Text Available This paper describes an approach to accurately separate out and quantify crop dominance areas in the major command area in the Krishna River Basin. Classification was performed using IRS-P6 (Indian Remote Sensing Satellite, series P6 and MODIS eight-day time series remote sensing images with a spatial resolution of 23.6 m, 250 m for the year 2005. Temporal variations in the NDVI (Normalized Difference Vegetation Index pattern obtained in crop dominance classes enables a demarcation between long duration crops and short duration crops. The NDVI pattern was found to be more consistent in long duration crops than in short duration crops due to the continuity of the water supply. Surface water availability, on the other hand, was dependent on canal water release, which affected the time of crop sowing and growth stages, which was, in turn, reflected in the NDVI pattern. The identified crop-wise classes were tested and verified using ground-truth data and state-level census data. The accuracy assessment was performed based on ground-truth data through the error matrix method, with accuracies from 67% to 100% for individual crop dominance classes, with an overall accuracy of 79% for all classes. The derived major crop land areas were highly correlated with the sub-national statistics with R2 values of 87% at the mandal (sub-district level for 2005–2006. These results suggest that the methods, approaches, algorithms and datasets used in this study are ideal for rapid, accurate and large-scale mapping of paddy rice, as well as for generating their statistics over large areas. This study demonstrates that IRS-P6 23.6-m one-time data fusion with MODIS 250-m time series data is very useful for identifying crop type, the source of irrigation water and, in the case of surface water irrigation, the way in which it is applied. The results from this study have assisted in improving surface water and groundwater irrigated areas of the command area and also

Shotgun metagenomics of 250 adult twins reveals genetic and environmental impacts on the gut microbiome

DEFF Research Database (Denmark)

Xie, Hailiang; Guo, Ruijin; Zhong, Huanzi

2016-01-01

The gut microbiota has been typically viewed as an environmental factor for human health. Twins are well suited for investigating the concordance of their gut microbiomes and decomposing genetic and environmental influences. However, existing twin studies utilizing metagenomic shotgun sequencing...... have included only a few samples. Here, we sequenced fecal samples from 250 adult twins in the TwinsUK registry and constructed a comprehensive gut microbial reference gene catalog. We demonstrate heritability of many microbial taxa and functional modules in the gut microbiome, including those...... associated with diseases. Moreover, we identified 8 million SNPs in the gut microbiome and observe a high similarity in microbiome SNPs between twins that slowly decreases after decades of living apart. The results shed new light on the genetic and environmental influences on the composition and function...

Tightening unit EZ 250 for VVER 1000 type reactor pressure vessel head flange joints

International Nuclear Information System (INIS)

Ruchar, Miloslav; Nadenik, Tomas; Kroj, Ludek

2010-01-01

The programme of flange joints tightening by seals made of expanded graphite for VVER 440 and VVER 1000 reactor head flange joints is highlighted, and tightening units of row EZ 650 and EZ 650 TK and KNI for VVER 440 reactor head flange joints and EZ 250 tightening unit for VVER 1000 reactor head flange joints are described in detail. The main advantages of electronically controlled tightening units include: Precise and uniform compression of the gasket during the tightening procedure; Automated solution to the graphite relaxing problem during tightening; Possibility of diagnosis of the thread status of the joints being tightened; Alleviation of operator's tough work; Shorter time of tensioning associated with a lower collective doses; Quick preparation of tightening procedure report from the data measured; Calibration renewal is possible in advance at time of unit storage without the need to place it on a real joint. (P.A.)

Conceptual design of the superconducting magnet for the 250 MeV proton cyclotron.

Science.gov (United States)

Ren, Yong; Liu, Xiaogang; Gao, Xiang

2016-01-01

The superconducting cyclotron is of great importance to treat cancer parts of the body. To reduce the operation costs, a superconducting magnet system for the 250 MeV proton cyclotron was designed to confirm the feasibility of the superconducting cyclotron. The superconducting magnet system consists of a pair of split coils, the cryostat and a pair of binary high temperature superconductor current leads. The superconducting magnet can reach a central magnetic field of about 1.155 T at 160 A. The three GM cryocooler with cooling capacities of 1.5 W at 4.5 K and 35 W at 50 K and one GM cryocooler of 100 W at 50 K were adopted to cool the superconducting magnet system through the thermosiphon technology. The four GM cryocoolers were used to cool the superconducting magnet to realize zero evaporation of the liquid helium.