WorldWideScience

Sample records for curium 247 target

  1. Critical and subcritical mass calculations of curium-243 to -247 based on JENDL-3.2 for revision of ANSI/ANS-8.15

    International Nuclear Information System (INIS)

    Okuno, Hiroshi

    2002-01-01

    Critical and subcritical masses were calculated for a sphere of five curium isotopes from 243 Cm to 247 Cm in metal and in metal-water mixtures considering three reflector conditions: bare, with a water reflector or a stainless steel reflector. The calculation were made mainly with a combination of a continuous energy Monte Carlo neutron transport calculation code, MCNP, and the Japanese Evaluated Nuclear Data Library, JENDL-3.2. Other evaluated nuclear data files, ENDF/B-VI and JEF-2.2, were also applied to find differences in calculation results of the neutron multiplication factor originated from different nuclear data files. A large dependence on the evaluated nuclear data files was found in the calculation results: more than 10%Δk/k relative differences in the neutron multiplication factor for a homogeneous mixture of 243 Cm metal and water when JENDL-3.2 was replaced with ENDF/B-VI and JEF-2.2, respectively; and a 44% reduction in the critical mass by changing from JENDL-3.2 to ENDF/B-VI for 246 Cm metal. The present study supplied basic information to the ANSI/ANS-8.15 Working Group for revision of the standard for nuclear criticality control of special actinide elements. The new or revised values of the subcritical mass limits for curium isotopes accepted by the ANSI/ANS-8.15 Working Group were finally summarized. (author)

  2. Critical and subcritical mass calculations of curium-243 to -247 based on JENDL-3.2 for revision of ANSI/ANS-8.15

    Energy Technology Data Exchange (ETDEWEB)

    Okuno, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kawasaki, Hiromitsu [CRC Solutions Corporation, Hitachinaka, Ibaraki (Japan)

    2002-10-01

    Critical and subcritical masses were calculated for a sphere of five curium isotopes from {sup 243}Cm to {sup 247}Cm in metal and in metal-water mixtures considering three reflector conditions: bare, with a water reflector or a stainless steel reflector. The calculation were made mainly with a combination of a continuous energy Monte Carlo neutron transport calculation code, MCNP, and the Japanese Evaluated Nuclear Data Library, JENDL-3.2. Other evaluated nuclear data files, ENDF/B-VI and JEF-2.2, were also applied to find differences in calculation results of the neutron multiplication factor originated from different nuclear data files. A large dependence on the evaluated nuclear data files was found in the calculation results: more than 10%{delta}k/k relative differences in the neutron multiplication factor for a homogeneous mixture of {sup 243}Cm metal and water when JENDL-3.2 was replaced with ENDF/B-VI and JEF-2.2, respectively; and a 44% reduction in the critical mass by changing from JENDL-3.2 to ENDF/B-VI for {sup 246}Cm metal. The present study supplied basic information to the ANSI/ANS-8.15 Working Group for revision of the standard for nuclear criticality control of special actinide elements. The new or revised values of the subcritical mass limits for curium isotopes accepted by the ANSI/ANS-8.15 Working Group were finally summarized. (author)

  3. Infrared spectrum of curium-244

    International Nuclear Information System (INIS)

    Conway, J.G.; Blaise, J.; Verges, J.

    1974-09-01

    The spectrum of curium-244 has been observed on the high resolution Fourier-transform spectrometer at Laboratoire Aime Cotton. An electrodeless lamp containing 50 μg of CmI 3 was run for 12 hours and 800,000 points were taken. A total of 1743 lines have been ascribed to curium and 87 percent of the lines have been assigned to transitions between known energy levels

  4. Extraction separation of americium and curium. A review

    International Nuclear Information System (INIS)

    Petrzilova, H.

    1976-11-01

    A survey is given of extraction systems suitable for transplutonium element separation and preparation as well as for the practical application of their nuclear properties. Methods are discussed in detail of separating the actinide and the lanthanide fractions from fission and corrosion products and of separating americium from curium. The description is completed with flowsheets showing the separation of transplutonium elements from irradiated targets and waste solutions after spent fuel reprocessing. (L.K.)

  5. Measurement of curium in marine samples

    Science.gov (United States)

    Schneider, D. L.; Livingston, H. D.

    1984-06-01

    Measurement of environmentally small but detectable amounts of curium requires reliable, accureate, and sensitive analytical methods. The radiochemical separation developed at Woods Hole is briefly reviewed with specific reference to radiochemical interferences in the alpha spectrometric measurement of curium nuclides and to the relative amounts of interferences expected in different oceanic regimes and sample types. Detection limits for 242 Cm and 244 Cm are ultimately limited by their presence in the 243Am used as curium yield monitor. Environmental standard reference materials are evaluated with regard to curium. The marine literature is reviewed and curium measurements are discussed in relation to their source of introduction to the environment. Sources include ocean dumping of low-level radioactive wastes and discharges from nuclear fuel reporcessing activities, In particular, the question of a detectable presence of 244Cm in global fallout from nuclear weapons testing is addressed and shown to be essentially negligible. Analyses of Scottish coastal sedimantes show traces of 242Cm and 244Cm activity which are believed to originate from transport from sources in the Irish Sea.

  6. Pretreatment of americium/curium solutions for vitrification

    International Nuclear Information System (INIS)

    Rudisill, T.S.

    1996-01-01

    Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to the heavy isotope programs at Oak Ridge National Laboratory. Prior to vitrification, an in-tank oxalate precipitation and a series of oxalic/nitric acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Pretreatment development experiments were performed to understand the behavior of the lanthanides and the metal impurities during the oxalate precipitation and properties of the precipitate slurry. The results of these experiments will be used to refine the target glass composition allowing optimization of the primary processing parameters and design of the solution transfer equipment

  7. Biological transport of curium-243 in dairy animals

    International Nuclear Information System (INIS)

    Sutton, W.W.; Patzer, R.G.; Hahn, P.B.; Potter, G.D.

    1979-04-01

    Lactating cows and goats were used to examine the biological transport of curium-243 in dairy animals. After either single oral or intravenous nuclide doses were administered, samples of milk, urine, blood, and feces were taken over a 144-hr priod, and the curium concentrations were determined by gamma counting. Gastrointestinal uptake of curium was estimated to be 0.02 and 0.006% of the oral dose for cows and goats, respectively. The cumulative percentage of oral dose transported to milk and urine was 4.6 x 10 -4 and 1.9 x 10 -3 , respectively, for a cow and 2.7 x 10 -4 and 1.6 x 10 -4 , respectively, for goats. Plasma concentrations of curium decreased rapidly following all intravenous injections. The average percentage of injected curium transferred to milk, urine, and feces was 2, 8, and 1, respectively, for a cow and 2, 5, and 5, respectively, for goats. All animals were sacrificed one week after dosing. Bovine bone retained the greatest fraction of the administered dose and the next highest was the liver. However, in all three intravenously dosed goats the liver contained the greatest amount of curium. Nuclide deposition in bone and liver was essentially equal for two of the three orally dosed goats while the skeleton contained the most curium in the other animal. Comparisons are presented between curium-243 and americium-241 transport in dairy cows

  8. Americium/curium bushing melter drain tests

    International Nuclear Information System (INIS)

    Smith, M.E.; Hardy, B.J.; Smith, M.E.

    1997-01-01

    Americium and curium were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. They have been stored in a nitric acid solution in an SRS reprocessing facility for a number of years. Vitrification of the americium/curium (Am/Cm) solution will allow the material to be safely stored or transported to the DOE Oak Ridge Reservation. Oak Ridge is responsible for marketing radionuclides for research and medical applications. The bushing melter technology being used in the Am/Cm vitrification research work is also under consideration for the stabilization of other actinides such as neptunium and plutonium. A series of melter drain tests were conducted at the Savannah River Technology Center to determine the relationship between the drain tube assembly operating variables and the resulting pour initiation times, glass flowrates, drain tube temperatures, and stop pour times. Performance criteria such as ability to start and stop pours in a controlled manner were also evaluated. The tests were also intended to provide support of oil modeling of drain tube performance predictions and thermal modeling of the drain tube and drain tube heater assembly. These drain tests were instrumental in the design of subsequent melter drain tube and drain tube heaters for the Am/Cm bushing melter, and therefore in the success of the Am/Cm vitrification and plutonium immobilization programs

  9. PROCESS FOR SEPARATING AMERICIUM AND CURIUM FROM RARE EARTH ELEMENTS

    Science.gov (United States)

    Baybarz, R.D.; Lloyd, M.H.

    1963-02-26

    This invention relates to methods of separating americium and curium values from rare earth values. In accordance with the invention americium, curium, and rare earth values are sorbed on an anion exchange resin. A major portion of the rare earth values are selectively stripped from the resin with a concentrated aqueous solution of lithium chloride, and americium, curium, and a minor portion of rare earth values are then stripped from the resin with a dilute aqueous solution of lithium chloride. The americium and curium values are further purified by increasing the concentration of lithium chloride in the solution to at least 8 molar and selectively extracting rare earth values from the resulting solution with a monoalkylphosphoric acid. (AEC)

  10. Americium/Curium Disposition Life Cycle Planning Study

    International Nuclear Information System (INIS)

    Jackson, W.N.; Krupa, J.; Stutts, P.; Nester, S.; Raimesch, R.

    1998-01-01

    At the request of the Department of Energy Savannah River Office (DOE- SR), Westinghouse Savannah River Company (WSRC) evaluated concepts to complete disposition of Americium and Curium (Am/Cm) bearing materials currently located at the Savannah River Site (SRS)

  11. Americium-curium vitrification process development

    International Nuclear Information System (INIS)

    Fellinger, A.P.; Baich, M.A.; Hardy, B.J

    1999-01-01

    The successful demonstration of sequentially drying, calcining and vitrifying an oxalate slurry in the Drain Tube Test Stand (DTTS) vessel provided the process basis for testing on a larger scale in a cylindrical induction heated melter. A single processing issue, that of batch volume expansion, was encountered during the initial stage of testing. The increase in batch volume centered on a sintered frit cap and high temperature bubble formation. The formation of a sintered frit cap expansion was eliminated with the use of cullet. Volume expansions due to high temperature bubble formation (oxygen liberation from cerium reduction) were mitigated in the DTTS melter vessel through a vessel temperature profile that effectively separated the softening point of the glass cullet and the evolving oxygen from cerium reduction. An increased processing temperature of 1,470 C and a two hour hold time to find any remaining bubbles successfully reduced bubbles in the poured glass to an acceptable level. The success of the preliminary process demonstrations provided a workable process basis that was directly applicable to the newly installed Cylindrical Induction Melter (CIM) system, making the batch flowsheet the preferred option for vitrification of the americium-curium surrogate feed stream

  12. Sorption of curium by silica colloids: Effect of humic acid

    International Nuclear Information System (INIS)

    Kar, Aishwarya Soumitra; Kumar, Sumit; Tomar, B.S.; Manchanda, V.K.

    2011-01-01

    Sorption of curium by silica colloids has been studied as a function of pH and ionic strength using 244 Cm as a tracer. The sorption was found to increase with increasing pH and reach a saturation value of ∼95% at pH beyond 5.3. The effect of humic acid on the sorption of 244 Cm onto silica was studied by changing the order of addition of the metal ion and humic acid. In general, in the presence of humic acid (2 mg/L), the sorption increased at lower pH (<5) while it decreased in the pH range 6.5-8 and above pH 8, the sorption was found to increase again. As curium forms strong complex with humic acid, its presence results in the enhancement of curium sorption at lower pH. At higher pH the humic acid present in the solution competes with the surface sites for curium thus decreasing the sorption. The decrease in the Cm sorption in presence of humic acid was found to be less when humic acid was added after the addition of curium. Linear additive model qualitatively reproduced the profile of the Cm(III) sorption by silica in presence of humic acid at least in the lower pH region, however it failed to yield quantitative agreement with the experimental results. The results of the present study evidenced the incorporation of Cm into the silica matrix.

  13. A contribution to preparative micro-chemistry and structural chemistry of element 96, curium

    International Nuclear Information System (INIS)

    Kohl, R.

    1984-01-01

    Ternary oxides of curium are analyzed by preparing a spectrum of different phases and characterizing it by radiography. Physical and thermodynamic data are established on curium trihalogenides. Particular interest is taken in experiments for preparing curium of the higher valency stages IV, V, and VI. (orig./PW) [de

  14. Process for the recovery of curium-244 from nuclear waste

    International Nuclear Information System (INIS)

    Posey, J.C.

    1980-10-01

    A process has been designed for the recovery of curium from purex waste. Curium and americium are separated from the lanthanides by a TALSPEAK extraction process using differential extraction. Equations were derived for the estimation of the economically optimum conditions for the extraction using laboratory batch extraction data. The preparation of feed for the extraction involves the removal of nitric acid from the Purex waste by vaporization under reduced pressure, the leaching of soluble nitrates from the resulting cake, and the oxalate precipitation of a pure lanthanide-actinide fraction. Final separation of the curium from americium is done by ion-exchange. The steps of the process, except ion-exchange, were tested on a laboratory scale and workable conditions were determined

  15. The biokinetics and radiotoxicology of curium: A comparison with americium

    Energy Technology Data Exchange (ETDEWEB)

    Menetrier, F. [CEA, Fontenay-aux-Roses (France); Taylor, D.M. [School of Chemistry, Cardiff University, Cardiff CF10 3AT (United Kingdom)], E-mail: davtay@btinternet.com; Comte, A. [CEA, Fontenay-aux-Roses (France)

    2008-05-15

    The human and animal data on the biokinetics of {sup 242}Cm and {sup 244}Cm are reviewed and shown to be very similar to those for {sup 241}Am. Liver and skeleton are the main organs of deposition and the retention of curium in the skeleton is very prolonged in all the species examined. Retention of both curium and americium in the liver appears to be species-dependent, being relatively rapidly removed from the liver of rats, and probably humans, but being tenaciously retained in dogs and some other species. The radiotoxicity of curium is also reviewed and it is shown that, as with {sup 241}Am, lung and bone tumour induction are the major hazards from inhaled and systemically deposited {sup 244}Cm. The use of chelating agents for the treatment of accidental contamination of the human body with {sup 242,244}Cm is also discussed.

  16. Subcellular distribution of curium in beagle liver

    International Nuclear Information System (INIS)

    Bruenger, F.W.; Grube, B.J.; Atherton, D.R.; Taylor, G.N.; Stevens, W.

    1976-01-01

    The subcellular distribution of curium ( 243 244 Cm) was studied in canine liver from 2 hr to 47 days after injection of 3 μCi 243 244 Cm/kg of body weight. The pattern of distribution for Cm was similar to other trivalent actinide elements studied previously (Am, Cf). Initially (2 hr), most of the nuclide was found in the cytosol and at least 90 percent was protein bound. About 70 percent of the Cm was bound to ferritin, approximately 5 percent was associated with a protein of MW approximately 200,000, and approximately 25 percent was found in the low-molecular-weight region (approximately 5000). The decrease in the Cm content of cytosol, nuclei, and microsomes coincided with an increase in the amount associated with mitochondria and lysosomes. The concentration of the Cm in the mitochondrial fraction was higher than it was in the lysosomal fraction at each time studied. In the mitochondrial fraction approximately 30 percent of the Cm was bound to membranous or granular material, and 70 percent was found in the soluble fraction. The Cm concentration initially associated with cell nuclei was high but had diminished to 20 percent of the 2 hr concentration by 20 days post injection (PI). The subcellular distribution of Cm in the liver of a dog which had received the same dose and was terminated because of severe liver damage was studied at 384 days PI. The liver weighed 130 g and contained approximately 30 percent of the injected Cm. In contrast, a normal liver weighs 280 g and at 2 hr PI contains approximately 40 percent of the injected dose. The subcellular distribution of Cm in this severely damaged liver differed from the pattern observed at earlier times after injection. The relative concentration of Cm in the cytosol was doubled; it was higher in the nuclei-debris fraction; and it was lower in the mitochondrial and lysosomal fractions when compared to earlier times

  17. Modelling of curium and americium behaviour during separation with displacing complexing chromatography

    International Nuclear Information System (INIS)

    Chuveleva, Eh.A.; Kharitonov, O.V.; Firsova, L.A.

    1994-01-01

    Certain heavy rare earths, curium and americium were separated by the method of displacement complexing chromatography using DTPA solutions and solutions containing DTPA and citric acid as eluents. Separation factors of rare earths and curium (americium) were calculated. Imitators for curium and americium separation were suggested: thulium for curium elution using 0.025 mol/l DTPA, holmium-for curium elution using 0.025 mol/l DTPA in the presence of 0.025 mol/l citric acid; terbium can serve as the imitator in both cases. 5 refs., 5 figs

  18. Calculation of prompt neutron spectra for curium isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Ohsawa, Takaaki [Kinki Univ., Higashi-Osaka, Osaka (Japan). Atomic Energy Research Inst.

    1997-03-01

    With the aim of checking the existing evaluations contained in JENDL-3.2 and providing new evaluations based on a methodology proposed by the author, a series of calculations of prompt neutron spectra have been undertaken for curium isotopes. Some of the evaluations in JENDL-3.2 was found to be unphysically hard and should be revised. (author)

  19. Determination of plutonium, americium and curium in the marine environment

    International Nuclear Information System (INIS)

    Grenaut, CLaude; Germain, Pierre; Miramand, Pierre.

    1982-01-01

    The method used in the Laboratory for plutonium, americium and curium determination in marine samples (water, sediments, animals, plants) is presented. It is a modification of a procedure based on adsorption on ion exchange resins developed by other authors. The preliminary preparation of the samples, the radiochemical procedures and electrodeposition are described so as to be used as a practical handbook [fr

  20. Thermodynamic systematics of oxides of americium, curium, and neighboring elements

    International Nuclear Information System (INIS)

    Morss, L.R.

    1984-01-01

    Recently-obtained calorimetric data on the sesquioxides and dioxides of americium and curium are summarized. These data are combined with other properties of the actinide elements to elucidate the stability relationships among these oxides and to predict the behavior of neighboring actinide oxides. 45 references, 4 figures, 5 tables

  1. The curium tagging approach for enhanced safeguards for spent fuel handling and reprocessing

    International Nuclear Information System (INIS)

    Menlove, H.O.; Beddingfield, D.H.; Rinard, P.M.; Wenz, T.R.

    1999-01-01

    Because of the intense neutron emission rate from curium, it can be a useful signature to measure and track special nuclear material in spent fuel and waste. By measuring the concentration of curium as well as plutonium and uranium in spent fuel streams, the ratio of curium to plutonium, uranium or other actinides can be used for waste assay. The quantity of special nuclear material in the waste streams such as the leached hulls and vitrified high-level waste can be calculated from the ratio of the curium to the plutonium, etc. The quantity of curium can be measured from the neutron emission rate from the various waste streams in the presence of the high-level gamma-ray backgrounds from fission products. Examples of using the curium ratio technique for measuring plutonium in leached hulls and vitrified waste canisters are presented in this paper. (author)

  2. Investigation of neutron resonances of 247Cm in the 0.5-20 eV energy range

    International Nuclear Information System (INIS)

    Belanova, T.S.; Kolesov, A.G.; Klinov, A.V.; Nikol'skij, S.N.; Poruchikov, V.A.; Nefedov, V.N.; Artamonov, V.S.; Ivanov, R.N.; Kalebin, S.M.

    1979-01-01

    The neutron resonance parameters of 247 Cm were calculated from the transmission of a curium sample measured by the time-of-flight method. The neutron resonance parameters were calculated by the shape method using the single-level Breit-Wigner formula. Since the neutron resonance parameters of 244 Cm, 245 Cm, 246 Cm, 248 Cm, 243 Am and 240 Pu are well known, it was possible to identify the neutron resonances of 247 Cm from the measured transmission and calculate their parameters. We identified only five neutron resonances of 247 Cm with high values of 2gGAMMAsub(n). This is due to the fact that the 247 Cm content of the sample is low (1.7mg) and the resonances of this isotope are identified against the background of a large number of resonances of 244 Cm, 245 Cm, 246 Cm, 248 Cm, 243 Am and 240 Pu situated in the energy range in question

  3. Gut uptake factors for plutonium, americium and curium

    International Nuclear Information System (INIS)

    Harrison, J.D.

    1982-01-01

    Data on estimates of the absorption of plutonium, americium and curium from the human gut based on measurements of uptake in other mammalian species are reviewed. It is proposed that for all adult members of the public ingesting low concentrations of plutonium in food and water, 0.05% would be an appropriate value of absorption except when the conditions of exposure are known and a lower value can be justified. For dietary intakes of americium and curium, the available data do not warrant a change from the ICRP value of 0.05%. For newborn children ingesting americium, curium and soluble forms of plutonium, a value of 1% absorption is proposed for the first 3 months of life during which the infant is maintained on a milk diet. It is proposed that a value of 0.5% should be used for the first year of life to take account of the gradual maturation of the gut. In considering the ingestion of insoluble oxides of plutonium by infants, it is proposed that absorption is taken as 0.1% for the first 3 months and 0.05% for the first year. (author)

  4. Plant uptake of americium, curium, and the chemical analog neodymium

    International Nuclear Information System (INIS)

    Weimer, W.C.; Laul, J.C.; Kutt, J.C.; Bondietti, E.A.

    1977-01-01

    The plant uptake from several bulk soils has been determined for neodymium, a chemical analog to the transuranium elements americium and curium, and several other native rare earth elements as well. These investigations have demonstrated that neodymium, which has very similar chemical properties to amercium and curium and should have a similar environmental behavior, does behave indistinguishably under both laboratory and field conditions. The uptake of the weathered or mobile forms of these elements from soils is expected to be governed primarily by their identical oxidation states and nearly identical ionic radii. This hypothesis is strongly supported by the chondritic (primordial) normalized rare earth element patterns in several plants. In these samples, the entire series of rare earth elements behaves as a smooth function of the REE ionic radii, as is also seen in the contiguous soils. This behavior suggests that the plant uptake of other ions with similar chemical properties (i.e., americium and curium) would also be governed by ionic size and charge

  5. Analytical separation of americium and curium, using high performance liquid chromatography

    International Nuclear Information System (INIS)

    Billon, A.

    1978-01-01

    Americium and curium are separated on a column of cation exchange resin (Aminex) using hydroxyisobutyric acid (α HIBA) as eluent, at a temperature of 80 0 C. Americium and curium were detected in line using their α emission: the separation was performed in a shielded glove box whose setting-up is given. Finally, the time necessary for a separation is comprised between 30 min and 1 hr. The purity of separated fractions was assayed by mass-spectrometry. An application in the determination of isotopic composition of americium and curium in fuels is described

  6. Americium/Curium Vitrification Pilot Tests - Part II

    International Nuclear Information System (INIS)

    Marra, J.E.; Baich, M.A.; Fellinger, A.P.; Hardy, B.J.; Herman, D.T.; Jones, T.M.; Miller, C.B.; Miller, D.H.; Snyder, T. K.; Stone, M.E.

    1998-05-01

    Isotopes of americium (Am) and curium (Cm) were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. These highly radioactive and valuable isotopes have been stored in an SRS reprocessing facility for a number of years. Vitrification of this solution will allow the material to be more safely stored until it is transported to the DOE Oak Ridge Reservation for use in research and medical applications. A previous paper described operation results from the Am-Cm Melter 2A pilot system, a full-scale non-radioactive pilot facility. This paper presents the results from continued testing in the Pilot Facility and also describes efforts taken to look at alternative vitrification process operations and flowsheets designed to address the problems observed during melter 2A pilot testing

  7. Remote micro-encapsulation of curium-gold cermets

    International Nuclear Information System (INIS)

    Coops, M.S.; Voegele, A.L.; Hayes, W.N.; Sisson, D.H.

    1980-01-01

    A technique is described for fabricating minature, high-density capsules of curium-244 oxide contained in three concentric jackets of metallic gold (or silver), with the outer surface being free of alpha contamination. The completed capsules are right circular cylinders 0.2500-inch diameter and 0.125-inch tall, with each level of containment soldered (or brazed) closed. A typical capsule would contain approx. 70 mg of 244 Cm (5.7 Ci) mixed with 120 mg of gold powder in the form of a cermet wafer clad in three concentric, 0.010-inch thick, liquid tight jackets. This method of fabrication eliminates voids between the jackets and produces a minimum size, maximum density capsule. Cermet densities of 11.5 g/cc were obtained, with an overall density of 17.3 g/cc for the finished capsule

  8. Preparation of curium-americium oxide microspheres by resin-bead loading

    International Nuclear Information System (INIS)

    Chattin, F.R.; Benker, D.E.; Lloyd, M.H.; Orr, P.B.; Ross, R.G.; Wiggins, J.T.

    1980-01-01

    Resin-bead loading and calcination techniques have been used to produce all curium and americium oxide feed material (about 2.2 kg) for HFIR targets since 1971. The process based on Dowex 50W resin has progressed from a series of test runs, through special production runs, into routine production in permanent equipment beginning in 1975. Key attributes of this process are its reliability, high yields, and ease of operation. The process is suited for remote operation in hot cells. Yields approaching 95% are routinely obtained and only one unacceptable product has been generated during routine production operations. There have been no problems in fabricating targets from this oxide or in the subsequent irradiation of these targets. The present scale of production of 150 to 250 g/y supplies the present need and is comparable with the level of other chemical process operations at TRU. Since the annual production is accomplished in two 8 to 12 day periods, there has been no reason to consider further scale-up. However, the rate of production could easily be doubled by simply adding a second set of calcination equipment

  9. Density of simulated americium/curium melter feed solution

    International Nuclear Information System (INIS)

    Rudisill, T.S.

    1997-01-01

    Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to Oak Ridge National Laboratory and use in heavy isotope production programs. Prior to vitrification, a series of in-tank oxalate precipitation and nitric/oxalic acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Following nitric acid dissolution and oxalate destruction, the solution will be denitrated and evaporated to a dissolved solids concentration of approximately 100 g/l (on an oxide basis). During the Am/Cm vitrification, an airlift will be used to supply the concentrated feed solution to a constant head tank which drains through a filter and an in-line orifice to the melter. Since the delivery system is sensitive to the physical properties of the feed, a simulated solution was prepared and used to measure the density as a function of temperature between 20 to 70 degrees C. The measured density decreased linearly at a rate of 0.0007 g/cm3/degree C from an average value of 1.2326 g/cm 3 at 20 degrees C to an average value of 1.1973g/cm 3 at 70 degrees C

  10. Americium/Curium Melter 2A Pilot Tests

    International Nuclear Information System (INIS)

    Smith, M.E.; Fellinger, A.P.; Jones, T.M.; Miller, C.B.; Miller, D.H.; Snyder, T.K.; Stone, M.E.; Witt, D.C.

    1998-05-01

    Isotopes of americium (Am) and curium (Cm) were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. These highly radioactive and valuable isotopes have been stored in an SRS reprocessing facility for a number of years. Vitrification of this solution will allow the material to be more safely stored until it is transported to the DOE Oak Ridge Reservation for use in research and medical applications. To this end, the Am/Cm Melter 2A pilot system, a full-scale non- radioactive pilot plant of the system to be installed at the reprocessing facility, was designed, constructed and tested. The full- scale pilot system has a frit and aqueous feed delivery system, a dual zone bushing melter, and an off-gas treatment system. The main items which were tested included the dual zone bushing melter, the drain tube with dual heating and cooling zones, glass compositions, and the off-gas system which used for the first time a film cooler/lower melter plenum. Most of the process and equipment were proven to function properly, but several problems were found which will need further work. A system description and a discussion of test results will be given

  11. Density of simulated americium/curium melter feed solution

    Energy Technology Data Exchange (ETDEWEB)

    Rudisill, T.S.

    1997-09-22

    Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to Oak Ridge National Laboratory and use in heavy isotope production programs. Prior to vitrification, a series of in-tank oxalate precipitation and nitric/oxalic acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Following nitric acid dissolution and oxalate destruction, the solution will be denitrated and evaporated to a dissolved solids concentration of approximately 100 g/l (on an oxide basis). During the Am/Cm vitrification, an airlift will be used to supply the concentrated feed solution to a constant head tank which drains through a filter and an in-line orifice to the melter. Since the delivery system is sensitive to the physical properties of the feed, a simulated solution was prepared and used to measure the density as a function of temperature between 20 to 70{degrees} C. The measured density decreased linearly at a rate of 0.0007 g/cm3/{degree} C from an average value of 1.2326 g/cm{sup 3} at 20{degrees} C to an average value of 1.1973g/cm{sup 3} at 70{degrees} C.

  12. Study of Reaction of Curium Oxy-Compound Formation in Molten Chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Osipenko, A.G.; Mayorshin, A.A.; Bychkov, A.V. [Dimitrovgrad-10, Ulyanovsk region, 433510 (Russian Federation)

    2008-07-01

    The method of potentiometric titration using oxygen sensors with solid electrolyte membrane was applied for the study of the interaction of curium cations with oxygen anions in the molten alkali metal chlorides in the temperature range of 450-850 C degrees depending on oxy-acidity of the environment. Assumptions were made concerning ion and phase composition of the obtained high-temperature compounds and chemical reactions taking place in the melts. This scheme assumes that as the basicity of the melt increases, initially the formation of soluble curium oxychlorides takes place in the melt (presumably CmO{sup -}) that is followed by formation of solid CmOCl and finally sesquioxide Cm{sub 2}O{sub 3}. Basic thermodynamic values were calculated for the resultant curium oxy-compounds.

  13. The rapid determination of americium curium, and uranium in urine by ultrafiltration

    International Nuclear Information System (INIS)

    Stradling, G.N.; Popplewell, D.S.; Ham, G.J.; Griffin, R.

    1975-01-01

    The rapid ultrafiltration method developed for the assay of plutonium has been extended to the determination of americium, curium and uranium in urine. The limits of detection for americium and curium, and uranium are 0.09 and 0.12 dm -1 l -1 respectively, and the analysis time excluding counting less than 2 hours. The method can therefor be effectively used as a rapid screening procedure. When the reference level for plutonium is exceeded, the α activity may require to be characterised. The single ultrafiltration technique must be modified for turbid urine samples. The method is inappropriate, except for uranium, when the urine contains DTPA. (author)

  14. National Low-Level Waste Management Program radionuclide report series. Volume 13, Curium-242

    International Nuclear Information System (INIS)

    Adams, J.P.

    1995-08-01

    This report, Volume 13 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of curium-242 ( 242 Cm). This report also includes discussions about waste types and forms in which 242 Cm can be found and 242 Cm behavior in the environment and in the human body

  15. Final report on the decontamination of the Curium Source Fabrication Facility

    International Nuclear Information System (INIS)

    Schaich, R.W.

    1983-12-01

    The Curium Source Fabrication Facility (CSFF) at Oak Ridge National Laboratory (ORNL) was decontaminated to acceptable contamination levels for maintenance activities, using standard decontamination techniques. Solid and liquid waste volumes were controlled to minimize discharges to the ORNL waste systems. This program required two years of decontamination effort at a total cost of approximately $700K. 5 references, 7 figures, 2 tables

  16. National Low-Level Waste Management Program radionuclide report series. Volume 13, Curium-242

    Energy Technology Data Exchange (ETDEWEB)

    Adams, J.P.

    1995-08-01

    This report, Volume 13 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of curium-242 ({sup 242}Cm). This report also includes discussions about waste types and forms in which {sup 242}Cm can be found and {sup 242}Cm behavior in the environment and in the human body.

  17. Safety analysis report for packaging (SARP) of the Oak Ridge National Laboratory. TRU curium shipping container

    International Nuclear Information System (INIS)

    Box, W.D.; Klima, B.B.; Seagren, R.D.; Shappert, L.B.; Aramayo, G.A.

    1980-06-01

    An analytical evaluation of the Oak Ridge National Laboratory Transuranium (TRU) Curium Shipping Container was made to demonstrate its compliance with the regulations governing offsite shipment of packages containing radioactive material. The evaluation encompassed five primary categories: structural integrity, thermal resistance, radiation shielding, nuclear criticality safety, and quality assurance. The results of the evaluation show that the container complies with the applicable regulations

  18. 7 CFR 247.27 - Financial management.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Financial management. 247.27 Section 247.27... AGRICULTURE CHILD NUTRITION PROGRAMS COMMODITY SUPPLEMENTAL FOOD PROGRAM § 247.27 Financial management. (a) What are the Federal requirements for State and local agencies with regard to financial management...

  19. 43 CFR 24.7 - Exemptions.

    Science.gov (United States)

    2010-10-01

    ... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Exemptions. 24.7 Section 24.7 Public Lands...-FEDERAL RELATIONSHIPS § 24.7 Exemptions. (a) Exempted from this policy are the following: (1) The control and regulation by the United States, in the area in which an international convention or treaty...

  20. 7 CFR 247.18 - Nutrition education.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Nutrition education. 247.18 Section 247.18 Agriculture... CHILD NUTRITION PROGRAMS COMMODITY SUPPLEMENTAL FOOD PROGRAM § 247.18 Nutrition education. (a) What are the State agency's responsibilities in ensuring that nutrition education is provided? The State agency...

  1. ISA 247: trans-ISA 247, trans-R 1524, ISA(TX)247, ISAtx 247, ISATx247, LX 211, LX211, R 1524, R-1524.

    Science.gov (United States)

    2007-01-01

    Isotechnika is developing the immunosuppressive drug ISA 247, a calcineurin inhibitor that is undergoing clinical development for the treatment of psoriasis (phase III) and prevention of organ rejection after transplantation (phase II). Preclinical development for uveitis is also underway. Other autoimmune disease indications that could be explored include arthritis, type I diabetes and Crohn's disease. ISA 247 was being co-developed as R 1524 by Isotechnika and Roche. However, Roche is no longer involved in the development of this compound. Based on analysis of previously collected data, the trans-ISA 247 isomer was found to be more bioavailable and it is expected that this isomer can be administered at a lower dose compared with the previous formulation that consisted of an equivalent mixture of the two geometric isomers (cis and trans). Preclinical observations indicate that ISA 247 has the potential to be more potent and less toxic than other marketed immunosuppressants in its class used for the prevention of transplant rejection. Experiments to date suggest that ISA 247 is about three times as potent as ciclosporin, while genotoxicity studies in animals have shown that the compound has a significantly reduced tendency to cause renal toxicity. The combination of reduced toxicity and improved potency would give ISA 247 a therapeutic benefit over existing calcineurin-based treatments. Isotechnika and Roche entered into a co-development and commercialisation agreement in April 2002, with Roche gaining the exclusive worldwide marketing rights for ISA 247; Isotechnika received milestone payments of $US4 million and $CAN21.9 million in September 2002 and May 2003, respectively. The agreement was restructured in April 2004, under which Isotechnika will now solely manage and fund the clinical development of trans-ISA 247. Upon successful completion of these trials, Isotechnika will conduct at its own expense a phase IIb study in renal transplantation and phase III

  2. Solubility of Plutonium (IV) Oxalate During Americium/Curium Pretreatment

    International Nuclear Information System (INIS)

    Rudisill, T.S.

    1999-01-01

    Approximately 15,000 L of solution containing isotopes of americium and curium (Am/Cm) will undergo stabilization by vitrification at the Savannah River Site (SRS). Prior to vitrification, an in-tank pretreatment will be used to remove metal impurities from the solution using an oxalate precipitation process. Material balance calculations for this process, based on solubility data in pure nitric acid, predict approximately 80 percent of the plutonium in the solution will be lost to waste. Due to the uncertainty associated with the plutonium losses during processing, solubility experiments were performed to measure the recovery of plutonium during pretreatment and a subsequent precipitation process to prepare a slurry feed for a batch melter. A good estimate of the plutonium content of the glass is required for planning the shipment of the vitrified Am/Cm product to Oak Ridge National Laboratory (ORNL).The plutonium solubility in the oxalate precipitation supernate during pretreatment was 10 mg/mL at 35 degrees C. In two subsequent washes with a 0.25M oxalic acid/0.5M nitric acid solution, the solubility dropped to less than 5 mg/mL. During the precipitation and washing steps, lanthanide fission products in the solution were mostly insoluble. Uranium, and alkali, alkaline earth, and transition metal impurities were soluble as expected. An elemental material balance for plutonium showed that greater than 94 percent of the plutonium was recovered in the dissolved precipitate. The recovery of the lanthanide elements was generally 94 percent or higher except for the more soluble lanthanum. The recovery of soluble metal impurities from the precipitate slurry ranged from 15 to 22 percent. Theoretically, 16 percent of the soluble oxalates should have been present in the dissolved slurry based on the dilution effects and volumes of supernate and wash solutions removed. A trace level material balance showed greater than 97 percent recovery of americium-241 (from the beta dec

  3. Actinide production in the reaction of heavy ions with curium-248

    International Nuclear Information System (INIS)

    Moody, K.J.

    1983-07-01

    Chemical experiments were performed to examine the usefulness of heavy ion transfer reactions in producing new, neutron-rich actinide nuclides. A general quasi-elastic to deep-inelastic mechanism is proposed, and the utility of this method as opposed to other methods (e.g. complete fusion) is discussed. The relative merits of various techniques of actinide target synthesis are discussed. A description is given of a target system designed to remove the large amounts of heat generated by the passage of a heavy ion beam through matter, thereby maximizing the beam intensity which can be safely used in an experiment. Also described is a general separation scheme for the actinide elements from protactinium (Z=91) to mendelevium (Z=101), and fast specific procedures for plutonium, americium and berkelium. The cross sections for the production of several nuclides from the bombardment of 248 Cm with 18 O, 86 Kr and 136 Xe projectiles at several energies near and below the Coulomb barrier were determined. The results are compared with yields from 48 Ca and 238 U bombardments of 248 Cm. Simple extrapolation of the product yields into unknown regions of charge and mass indicates that the use of heavy ion transfer reactions to produce new, neutron-rich above-target species is limited. The substantial production of neutron-rich below-target species, however, indicates that with very heavy ions like 136 Xe and 238 U the new species 248 Am, 249 Am and 247 Pu should be produced with large cross sections from a 248 Cm target. A preliminary, unsuccessful attempt to isolate 247 Pu is outlined. The failure is probably due to the half life of the decay, which is calculated to be less than 3 minutes. The absolute gamma ray intensities from 251 Bk decay, necessary for calculating the 251 Bk cross section, are also determined

  4. Quantitative determination of americium and curium in solutions using potassium tungstophosphate

    International Nuclear Information System (INIS)

    Chistyakov, V.M.; Baranov, A.A.; Erin, E.A.; Timoaeev, G.A.

    1990-01-01

    Two methods of americium (4) and curium (4) titration-replacement and redox ones - have been considered. According to the replacement method thorium nitrate solution was used as a titrant and the final point of titration was determined spectophotometrically. Using the method developed, on the basis of experimental data, the composition of thorium (4) complex with potassium tungstophosphate was determined. In case of the redox titration sodium nitrite was used, and the final titration point was indicated either spectrophotometrically or potentiometrically

  5. In vitro dissolution of curium oxide using a phagolysosomal simulant solvent system

    International Nuclear Information System (INIS)

    Helfinstine, S.Y.; Guilmette, R.A.; Schlapper, G.A.

    1992-01-01

    Detailed study of actinide oxide behavior in alveolar macrophages (AM) in vitro is limited because of the short life span of these cells in culture. We created an in vitro dissolution system that could mimic the acidic phagolysosomal environment for the actinide and be maintained for an indefinite period so that dissolution of more insoluble materials could be measured. The dissolution system for this investigation, consisting of nine different solutions of HCl and the chelating agent diethylenetriamine pentaacetate (DTPA) in distilled water, is called the phagolysosomal simulant solvent (PSS). In this system, both the pH and the amount of DTPA were varied. We could observe the effect of altering pH within a range of 4.0-6.0 (similar to that of the phagolysosome) and the effect of the molar ratio of DTPA to curium at 1000: 1, 100;1, or 10:1. We chose curium sesquioxide ( 244 Cm 2 O 3 ) to validate the PSS for actinide dissolution versus that occurring in AM in vitro because it dissolves significantly in less than 1 week. The polydisperse 244 Cm 2 O 3 aerosol was generated, collected on filters, resuspended, and added to the PSS solutions and to cultured canine AM. By comparing dissolution in the two systems directly, we hoped to arrive at an optimum PSS for future dissolution studies. PSS and cell culture samples were taken daily for 7 days after exposure and tested for the solubilized curium. The amount of soluble material was determined by ultracentrifugation to separate the insoluble CM 2 O 3 from the soluble curium in the PSS solutions and filtration for the cell-containing material. After separating the soluble and insoluble fractions, the samples were analyzed using alpha liquid scintillation counting. Time-dependent dissolution measurements from the PSS/AM showed that the CM 2 O 3 dissolution was similar for both the PSS solutions and the cultured AM. 13 refs., 4 tabs

  6. Spectroscopic and redox properties of curium and californium ions in concentrated aqueous carbonate-bicarbonate media

    International Nuclear Information System (INIS)

    Hobart, D.E.; Varlashkin, P.G.; Samhoun, K.; Haire, R.G.; Peterson, J.R.

    1983-01-01

    Multimilligram quantities of trivalent curium-248 and californium-249 were investigated by absorption spectroscopy, cyclic voltammetry, and bulk solution electrolysis in concentrated aqueous carbonate-bicarbonate solution. Actinide concentrations between 10 -4 and 10 -2 M were studied in 2 M sodium carbonate and 5.5 M potassium carbonate solutions at pH values from 8 to 14. The solution absorption spectra of Cm(III) and Cf(III) in carbonate media are presented for the first time and compared to literature spectra of these species in noncomplexing aqueous solution. It was anticipated that carbonate complexation of the actinide ions could provide a sufficient negative shift in the formal potentials of the M(IV)/M(III) couples of Cm and Cf to permit the generation and stabilization of their tetravalent states in aqueous carbonate-bicarbonate medium. No conclusive evidence was found in the present work to indicate the existence of any higher oxidation states of curium or californium in carbonate solution. Some possible reasons for our inability to generate and detect oxidized species of curium and californium in this medium are discussed

  7. Development of analytical methods for the separation of plutonium, americium, curium and neptunium from environmental samples

    Energy Technology Data Exchange (ETDEWEB)

    Salminen, S.

    2009-07-01

    In this work, separation methods have been developed for the analysis of anthropogenic transuranium elements plutonium, americium, curium and neptunium from environmental samples contaminated by global nuclear weapons testing and the Chernobyl accident. The analytical methods utilized in this study are based on extraction chromatography. Highly varying atmospheric plutonium isotope concentrations and activity ratios were found at both Kurchatov (Kazakhstan), near the former Semipalatinsk test site, and Sodankylae (Finland). The origin of plutonium is almost impossible to identify at Kurchatov, since hundreds of nuclear tests were performed at the Semipalatinsk test site. In Sodankylae, plutonium in the surface air originated from nuclear weapons testing, conducted mostly by USSR and USA before the sampling year 1963. The variation in americium, curium and neptunium concentrations was great as well in peat samples collected in southern and central Finland in 1986 immediately after the Chernobyl accident. The main source of transuranium contamination in peats was from global nuclear test fallout, although there are wide regional differences in the fraction of Chernobyl-originated activity (of the total activity) for americium, curium and neptunium. The separation methods developed in this study yielded good chemical recovery for the elements investigated and adequately pure fractions for radiometric activity determination. The extraction chromatographic methods were faster compared to older methods based on ion exchange chromatography. In addition, extraction chromatography is a more environmentally friendly separation method than ion exchange, because less acidic waste solutions are produced during the analytical procedures. (orig.)

  8. 40 CFR 247.13 - Transportation products.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Transportation products. 247.13 Section 247.13 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES... Transportation products. (a) Traffic barricades and traffic cones used in controlling or restricting vehicular...

  9. Curium Management Studies in France, Japan and USA. A Report by the WPFC Expert Group on Chemical Partitioning of the NEA Nuclear Science Committee - April 2011

    International Nuclear Information System (INIS)

    Yamagishi, Isao; Choi, Yong-Joon; Glatz, Jean-Paul; Hyland, Bronwyn; Uhlir, Jan; Baron, Pascal; Warin, Dominique; DE ANGELIS, Giorgio; LUCE, Alfredo; Inoue, Tadashi; Morita, Yasuji; Minato, Kazuo; Lee, Han Soo; Ignatiev, Victor V.; Kormilitsyn, Mikhail V.; Caravaca, Concepcion; Lewin, Robert g.; Taylor, Robin J.; Collins, Emory D.; Laidler, James J.

    2012-01-01

    Curium is closely associated with americium in irradiated fuels because of their chemical similarity with regard to potential separation requirements, and because americium also requires special shielding and handling requirements due to its gamma radiation emission. Americium is produced in greater mass than curium in irradiated nuclear fuels and the mass ratio can grow exponentially with decay time because of the simultaneous decay of 244 Cm and in-growth of 241 Am from decay of 241 Pu (half-life = 14.4 years). For these reasons, curium management is challenging. Countries that are now engaged in or planning future fuel recycle operations, are considering methods to manage the curium produced and minimise the shielding and handling requirements, as well as the reprocessing requirements for separation of curium from americium France, Japan, and the USA have begun curium management studies. Curium management methods under consideration include (1) separation of curium from americium and storage of curium for several decades to allow 244 Cm to decay substantially to 240 Pu, while moving ahead to recycle americium; (2) recycling of americium and curium without separation; and (3) waiting several decades to reprocess used nuclear fuels, allowing decay minimisation of curium emissions and the requirement for separation of curium from americium, and allowing an alteration of the subsequent transmutation path to reduce the production of curium in recycled used fuels. In this report, recent curium management studies in France, Japan, and the USA have been described. The French studies included scenarios that compared the recycle of ail minor actinides (neptunium, americium, and curium) with the recycle of only neptunium and americium in radial blankets of sodium-cooled fast reactors (SFR). In the latter scenario, curium is separated from americium during used fuel reprocessing and stored for 5000 years to allow 244 Cm to decay to 240 Pu which is then recycled. Even though

  10. Erythroderma: analysis of 247 cases

    Directory of Open Access Journals (Sweden)

    Cidia Vasconcellos

    1995-06-01

    Full Text Available The profile of 247 patients with erythroderma during a 23 year period from January, 1962 through March, 1985, with a follow-up period ranging from 1 to 26 years were analysed. The patients presented with diffuse erythema, scaling and pruritus of more than 2 months' duration, and the age ranged from 16 to 60 years. Psoriasis was the most frequent underlying disease with an estimated frequency of 44.9%, the reaction to the use of drugs appeared in 7.3% of total cases and association with reticulosis showed a frequency of 4.1%. The cause of the erythroderma could not be determined in 29.2% of the cases. Sex differences in terms of underlying diseases were not observed. One or more skin biopsies along with the clinical findings were diagnostic or suggestive of the underlying disease in 63.6% of the cases. Repeated skin biopsies are recommended as the best method for etiologic diagnosis of erythroderma. At P=0.05 significance level, masculine/feminine ratio of 2 : 1 was found. The question arises wether causal agent of erythroderma may not be somehow related to different exposure by sex to environmental antigens.

  11. Erythroderma: analysis of 247 cases

    Directory of Open Access Journals (Sweden)

    Vasconcellos Cidia

    1995-01-01

    Full Text Available The profile of 247 patients with erythroderma during a 23 year period from January, 1962 through March, 1985, with a follow-up period ranging from 1 to 26 years were analysed. The patients presented with diffuse erythema, scaling and pruritus of more than 2 months' duration, and the age ranged from 16 to 60 years. Psoriasis was the most frequent underlying disease with an estimated frequency of 44.9%, the reaction to the use of drugs appeared in 7.3% of total cases and association with reticulosis showed a frequency of 4.1%. The cause of the erythroderma could not be determined in 29.2% of the cases. Sex differences in terms of underlying diseases were not observed. One or more skin biopsies along with the clinical findings were diagnostic or suggestive of the underlying disease in 63.6% of the cases. Repeated skin biopsies are recommended as the best method for etiologic diagnosis of erythroderma. At P=0.05 significance level, masculine/feminine ratio of 2 : 1 was found. The question arises wether causal agent of erythroderma may not be somehow related to different exposure by sex to environmental antigens.

  12. 24/7 SM slavery.

    Science.gov (United States)

    Dancer, Peter L; Kleinplatz, Peggy J; Moser, Charles

    2006-01-01

    This study describes the nature of 24/7 SM slavery as practiced within the SM (sadomasochistic) community. These SM participants, who attempt to live full-time in owner-slave roles, represent a small proportion of those with SM interests. SM slaves have not been studied systematically to determine if and how they differ from other SM practitioners. An online questionnaire was used to obtain responses from individuals who self-identified as slaves. A total of 146 respondents participated, 53% female and 47% male, ranging in age from 18 to 72. We explored the depth of their relationships, how well they approximated "slavery," and how their relationships were structured to maintain distinct roles. Data showed that in long-term SM slave relationships, a power differential exists which extends beyond time-limited SM or sexual interactions. Owners and slaves often use common, daily life experiences or situations, such as the completion of household chores, money management, and morning or evening routines, to distinguish and maintain their respective roles. In addition, contrary to the perception of total submission, results revealed that slaves exercise free will when it is in their best interests to do so. These relationships were long-lasting and satisfying to the respondents.

  13. Dicty_cDB: SLH247 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SL (Link to library) SLH247 (Link to dictyBase) - - - Contig-U16280-1 SLH247Z (Link... to Original site) - - SLH247Z 632 - - - - Show SLH247 Library SL (Link to library) Clone ID SLH247 (Link to...ycdb.biol.tsukuba.ac.jp/CSM/SL/SLH2-B/SLH247Q.Seq.d/ Representative seq. ID SLH24...7Z (Link to Original site) Representative DNA sequence >SLH247 (SLH247Q) /CSM/SL/SLH2-B/SLH247Q.Seq.d/ XXXXX...ant alignments: (bits) Value SLH247 (SLH247Q) /CSM/SL/SLH2-B/SLH247Q.Seq.d/ 1253 0.0 SLA487 (SLA487Q) /CSM/S

  14. Erythroderma: analysis of 247 cases

    Directory of Open Access Journals (Sweden)

    Cidia Vasconcellos

    1995-06-01

    Full Text Available The profile of 247 patients with erythroderma during a 23 year period from January, 1962 through March, 1985, with a follow-up period ranging from 1 to 26 years were analysed. The patients presented with diffuse erythema, scaling and pruritus of more than 2 months' duration, and the age ranged from 16 to 60 years. Psoriasis was the most frequent underlying disease with an estimated frequency of 44.9%, the reaction to the use of drugs appeared in 7.3% of total cases and association with reticulosis showed a frequency of 4.1%. The cause of the erythroderma could not be determined in 29.2% of the cases. Sex differences in terms of underlying diseases were not observed. One or more skin biopsies along with the clinical findings were diagnostic or suggestive of the underlying disease in 63.6% of the cases. Repeated skin biopsies are recommended as the best method for etiologic diagnosis of erythroderma. At P=0.05 significance level, masculine/feminine ratio of 2 : 1 was found. The question arises wether causal agent of erythroderma may not be somehow related to different exposure by sex to environmental antigens.Foi analisado o perfil de 247 doentes com eritrodermia em um período de 23 anos, de Janeiro de 1962 a março de 1985, com o período de seguimento variando de 1 a 26 anos. Os doentes se apresentavam com eritema universal, descamação e prurido com mais de 2 meses de duração e a idade variava de 16 a 60 anos. A psoríase foi a doença associada mais freqüente, com uma proporção estimada de 44,9%, as reações cutâneas ao uso de drogas contribuíram com 7,3% do total de casos e a associação com reticuloses mostrou uma proporção de 4,1%. A eritrodermia permaneceu como de causa desconhecida em 29,2% dos casos. Não foram observadas diferenças entre os sexos no que diz respeito à doença associada. Um ou mais resultados anátomo patológicos das biópsias de pele, em conjunto com o quadro clínico, foi diagnóstico ou sugestivo do

  15. Type B investigation report of curium-244 exposure at the ORNL TRU Facility, January 15, 1986

    International Nuclear Information System (INIS)

    Love, G.L.; Butler, H.M.; Duncan, D.T.; Oakes, T.W.

    1986-04-01

    This Type B Investigative Report provides an evaluation of relevant events and activities that led to, were a part of, or resulted from the release of curium-244 in the Building 7920 facility at ORNL in January 1986. Impacts have been evaluated with respect to employee exposures and the costs and loss of productivity resulting from increased bioassay analyses and activities of investigative committees. Management systems evaluated include (1) training of employees performing lab analyses, (2) adherence to procedures, and (3) response to unusual circumstances

  16. Cleanex process: a versatile solvent extraction process for recovery and purification of lanthanides, americium, and curium

    International Nuclear Information System (INIS)

    Bigelow, J.E.; Collins, E.D.; King, L.J.

    1979-01-01

    At a concentration of 1 M in straight-chain hydrocarbon diluent, HDEHP will extract americium, curium, and other trivalent actinide and lanthanide elements from dilute acid or salt solutions. The solute is back-extracted with more concentrated acid, either nitric or hydrochloric. The process has been used in the continuous, countercurrent mode, but its greatest advantage arises in batch extractions where the excess acid can be titrated with NaOH to produce a final acidity of about 0.03 M. Under these conditions, 99% recovery can be achieved, usually in one stage. Cleanex was used on the 50-liter scale at the Transuranium Processing Plant at Oak Ridge for 12 years to provide a broad spectrum cleanup to transuranium elements before applying more sophisticated techniques for separating individual products. The process is also used routinely to recover excessive losses of curium and/or californium from plant waste streams. The solvent system is relatively resistant to radiation damage, being usable up to 200 W-h/liter

  17. Vitrification of F-area americium/curium: feasibility study and preliminary process recommendation

    International Nuclear Information System (INIS)

    Ramsey, W.G.; Miller, D.; Minichan, R.; Coleman, L.; Schumacher, R.; Hardy, B.; Jones, R.

    1994-01-01

    Work was performed to identify a process to vitrify the contents of F- canyon Tank 17.1. Tank 17.1 contains the majority of americium (Am) and curium (Cm) contained in the DOE Complex. Oak Ridge National Laboratory (ORNL) has made a formal request for this material as fuel for production of Cf252 and other transplutonium actinides. The Am and Cm (and associated lanthanide fission products) are currently in nitric acid solution. Transportation of the intensely radioactive Am/Cm in liquid form is not considered possible. As a result, the material will either be solidified and shipped to ORNL or discarded to the Tank Farm. Nuclear Materials Processing Technology (NMPT), therefore, requested Defense Waste Processing Technology (DWPT) to determine if the Tank 17.1 material could be vitrified, and if it was vitrified could the americium and curium be successfully recovered. Research was performed to determine if the Tank 17.1 contents could indeed be mixed with glass formers and vitrified. Additional studies identified critical process parameters such as heat loading, melter requirements, off-gas evolution, etc. Discussions with NMPT personnel were initiated to determine existing facilities where this work could be accomplished safely. A process has been identified which will convert the Am/Cm material into approximately 300kg of glass

  18. Actinide production from xenon bombardments of curium-248

    International Nuclear Information System (INIS)

    Welch, R.B.

    1985-01-01

    Production cross sections for many actinide nuclides formed in the reaction of 129 Xe and 132 Xe with 248 Cm at bombarding energies slightly above the coulomb barrier were determined using radiochemical techniques to isolate these products. These results are compared with cross sections from a 136 Xe + 248 Cm reaction at a similar energy. When compared to the reaction with 136 Xe, the maxima in the production cross section distributions from the more neutron deficient projectiles are shifted to smaller mass numbers, and the total cross section increases for the production of elements with atomic numbers greater than that of the target, and decreases for lighter elements. These results can be explained by use of a potential energy surface (PES) which illustrates the effect of the available energy on the transfer of nucleons and describes the evolution of the di-nuclear complex, an essential feature of deep-inelastic reactions (DIR), during the interaction. The other principal reaction mechanism is the quasi-elastic transfer (QE). Analysis of data from a similar set of reactions, 129 Xe, 132 Xe, and 136 Xe with 197 Au, aids in explaining the features of the Xe + Cm product distributions, which are additionally affected by the depletion of actinide product yields due to deexcitation by fission. The PES is shown to be a useful tool to predict the general features of product distributions from heavy ion reactions

  19. The use of curium neutrons to verify plutonium in spent fuel and reprocessing wastes

    International Nuclear Information System (INIS)

    Miura, N.

    1994-05-01

    For safeguards verification of spent fuel, leached hulls, and reprocessing wastes, it is necessary to determine the plutonium content in these items. We have evaluated the use of passive neutron multiplicity counting to determine the plutonium content directly and also to measure the 240 Pu/ 244 Cm ratio for the indirect verification of the plutonium. Neutron multiplicity counting of the singles, doubles, and triples neutrons has been evaluated for measuring 240 Pu, 244 Cm, and 252 Cf. We have proposed a method to establish the plutonium to curium ratio using the hybrid k-edge densitometer x-ray fluorescence instrument plus a neutron coincidence counter for the reprocessing dissolver solution. This report presents the concepts, experimental results, and error estimates for typical spent fuel applications

  20. Transmutation of americium and curium incorporated in zirconia-based host materials

    International Nuclear Information System (INIS)

    Raison, P.E.

    2001-01-01

    Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO 2 -ZrO 2 -Y 2 O 3 . It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO 2 content. The Cm 2 O 3 -ZrO 2 system was also investigated. It was found that at 25 mol% of CmO 1.5 , the Cm(III) stabilized zirconia in its cubic form (a = 5.21 ±0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO 1.5 , a pyrochlore oxide - Cm 2 Zr 2 O 7 - is formed (a = 10.63 ±0.02 Angstrom). (author)

  1. 32 CFR 247.1 - Purpose.

    Science.gov (United States)

    2010-07-01

    ... DEFENSE NEWSPAPERS, MAGAZINES AND CIVILIAN ENTERPRISE PUBLICATIONS § 247.1 Purpose. This part implements DoD Directive 5122.10 1 and implements policy, assigns responsibilities, and prescribes procedures concerning authorized DoD Appropriated Funded (APF) newspapers and magazines, and Civilian Enterprise (CE...

  2. 7 CFR 247.6 - State Plan.

    Science.gov (United States)

    2010-01-01

    ... serving women, infants, and children, program outreach, and nutrition education. (Collaboration with the... CHILD NUTRITION PROGRAMS COMMODITY SUPPLEMENTAL FOOD PROGRAM § 247.6 State Plan. (a) What is the State... women, infants, and children, and the options to be used relating to income or other eligibility...

  3. Application of curium measurements for safeguarding at reprocessing plants. Study 1: High-level liquid waste and Study 2: Spent fuel assemblies and leached hulls

    International Nuclear Information System (INIS)

    Rinard, P.M.; Menlove, H.O.

    1996-03-01

    In large-scale reprocessing plants for spent fuel assemblies, the quantity of plutonium in the waste streams each year is large enough to be important for nuclear safeguards. The wastes are drums of leached hulls and cylinders of vitrified high-level liquid waste. The plutonium amounts in these wastes cannot be measured directly by a nondestructive assay (NDA) technique because the gamma rays emitted by plutonium are obscured by gamma rays from fission products, and the neutrons from spontaneous fissions are obscured by those from curium. The most practical NDA signal from the waste is the neutron emission from curium. A diversion of waste for its plutonium would also take a detectable amount of curium, so if the amount of curium in a waste stream is reduced, it can be inferred that there is also a reduced amount of plutonium. This report studies the feasibility of tracking the curium through a reprocessing plant with neutron measurements at key locations: spent fuel assemblies prior to shearing, the accountability tank after dissolution, drums of leached hulls after dissolution, and canisters of vitrified high-level waste after separation. Existing pertinent measurement techniques are reviewed, improvements are suggested, and new measurements are proposed. The authors integrate these curium measurements into a safeguards system

  4. A time-resolved laser fluorescence spectroscopy (TRLFS) study of the interaction of trivalent actinides (curium(III)) with calcite

    International Nuclear Information System (INIS)

    Stumpf, Th.; Fanghaenel, Th.

    2002-01-01

    Cm(III) interaction with calcite was investigated in the trace concentration range. Two different Cm(III)/calcite sorption species were found. The first Cm(III) sorption species consists of a curium ion that is bonded onto the calcite surface. The second Cm(III) sorption species has lost its complete hydration sphere and is incorporated into the calcite bulk structure /1/. (orig.)

  5. Gas-Phase Energetics of Actinide Oxides: An Assessment of Neutral and Cationic Monoxides and Dioxides from Thorium to Curium

    Science.gov (United States)

    Marçalo, Joaquim; Gibson, John K.

    2009-09-01

    An assessment of the gas-phase energetics of neutral and singly and doubly charged cationic actinide monoxides and dioxides of thorium, protactinium, uranium, neptunium, plutonium, americium, and curium is presented. A consistent set of metal-oxygen bond dissociation enthalpies, ionization energies, and enthalpies of formation, including new or revised values, is proposed, mainly based on recent experimental data and on correlations with the electronic energetics of the atoms or cations and with condensed-phase thermochemistry.

  6. 48 CFR 52.247-2 - Permits, Authorities, or Franchises.

    Science.gov (United States)

    2010-10-01

    ... Franchises. 52.247-2 Section 52.247-2 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION....247-2 Permits, Authorities, or Franchises. As prescribed in 47.207-1(a), insert the following clause: Permits, Authorities, or Franchises (JAN 1997) (a) The offeror does □, does not □, hold authorization from...

  7. 25 CFR 247.18 - What are the sanitation prohibitions?

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false What are the sanitation prohibitions? 247.18 Section 247.18 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR FISH AND WILDLIFE USE OF COLUMBIA RIVER TREATY FISHING ACCESS SITES § 247.18 What are the sanitation prohibitions? (a) You cannot deposit...

  8. 48 CFR 52.247-60 - Guaranteed Shipping Characteristics.

    Science.gov (United States)

    2010-10-01

    ... Characteristics. 52.247-60 Section 52.247-60 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION....247-60 Guaranteed Shipping Characteristics. As prescribed in 47.305-16(b)(1), insert the following clause: Guaranteed Shipping Characteristics (DEC 1989) (a) The offeror is requested to complete...

  9. 43 CFR 2.47 - Records subject to Privacy Act.

    Science.gov (United States)

    2010-10-01

    ... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Records subject to Privacy Act. 2.47 Section 2.47 Public Lands: Interior Office of the Secretary of the Interior RECORDS AND TESTIMONY; FREEDOM OF INFORMATION ACT Privacy Act § 2.47 Records subject to Privacy Act. The Privacy Act applies to all...

  10. Towards 24/7 continuous heart rate monitoring.

    Science.gov (United States)

    Tarniceriu, Adrian; Parak, Jakub; Renevey, Philippe; Nurmi, Marko; Bertschi, Mattia; Delgado-Gonzalo, Ricard; Korhonen, Ilkka

    2016-08-01

    Heart rate (HR) and HR variability (HRV) carry rich information about physical activity, mental and physical load, physiological status, and health of an individual. When combined with activity monitoring and personalized physiological modelling, HR/HRV monitoring may be used for monitoring of complex behaviors and impact of behaviors and external factors on the current physiological status of an individual. Optical HR monitoring (OHR) from wrist provides a comfortable and unobtrusive method for HR/HRV monitoring and is better adhered by users than traditional ECG electrodes or chest straps. However, OHR power consumption is significantly higher than that for ECG based methods due to the measurement principle based on optical illumination of the tissue. We developed an algorithmic approach to reduce power consumption of the OHR in 24/7 HR trending. We use continuous activity monitoring and a fast converging frequency domain algorithm to derive a reliable HR estimate in 7.1s (during outdoor sports, in average) to 10.0s (during daily life). The method allows >80% reduction in power consumption in 24/7 OHR monitoring when average HR monitoring is targeted, without significant reduction in tracking accuracy.

  11. Interactions of Microbes found at Aespoe Underground Lab with Actinides such as Curium, Plutonium and Uranium

    Energy Technology Data Exchange (ETDEWEB)

    Moll, H.; Merroun, M.; Geipel, G.; Rossberg, A.; Hennig, C.; Selenska-Pobell , S.; Bernhard, G. [Forschungszentrum Dresden-Rossendorf e.V., Inst. fuer Radioc hemie, 01314 Dresden (Germany)]. e-mail: h.moll@fzd.de; Stumpf, Th. [Forschungszentru m Karlsruhe, Inst. fuer Nukleare Entsorgung, 76021 Karlsruhe (Germany)

    2007-06-15

    Sulfate-reducing bacteria (SRB) frequently occur in the deep granitic rock aquifers at the Aespoe Hard Rock Laboratory (Aespoe HRL), Sweden. The new SRB strain Desulfovibrio aespoeensis could be isolated. Results describing the basic interaction mechanisms of uranium, curium, and plutonium with cells of D. aespoeensis DSM 10631T will be presented. The interaction experiments with the actinides showed that the cells are able to remove all three actinides from the surrounding solution. The amount of removed actinide and the interaction mechanism varied among the different actinides. The main U(VI) removal occurred after the first 24 h. The contact time, pH and [U(VI)]initial influence the U removal efficiency. The presence of uranium caused a damaging of the cell membranes. TEM revealed an accumulation of U inside the bacterial cell. D. aespoeensis are able to form U(IV). A complex interaction mechanism takes place consisting of biosorption, bioreduction and bioaccumulation. In the case of {sup 242}Pu, solvent extractions, UV-vis- and XANES spectroscopy were used to determine the speciation of the Pu oxidation states. In the first step, the Pu(VI) and Pu(IV)-polymers are bound to the biomass. Solvent extractions showed that 97 % of the initially present Pu(VI) is reduced to Pu(V) due to the activity of the cells within the first 24 h. Most of the formed Pu(V) dissolves from the cell envelope back to the aqueous solution due to the weak complexing properties of this plutonium oxidation state. In the case of curium at a much lower metal concentration of 3x10{sup -7} M, a pure biosorption of Cm(III) on the cell envelope forming an inner-sphere surface complex most likely with organic phosphate groups was detected. To summarize, the strength of the interaction of D. aespoeensis with the selected actinides at pH 5 and actinide concentrations = 10 mg/L ([Cm] 0.07 mg/L) follows the pattern: Cm > U > Pu >> Np.

  12. Transmutation of americium and curium incorporated in zirconia-based host materials

    Energy Technology Data Exchange (ETDEWEB)

    Raison, P.E. [CEA Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d' Etudes des Combustibles; Haire, R.G. [Oak Ridge National Lab., TN (United States)

    2001-07-01

    Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO{sub 2}-ZrO{sub 2}-Y{sub 2}O{sub 3}. It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO{sub 2} content. The Cm{sub 2}O{sub 3}-ZrO{sub 2} system was also investigated. It was found that at 25 mol% of CmO{sub 1.5}, the Cm(III) stabilized zirconia in its cubic form (a = 5.21 {+-}0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO{sub 1.5}, a pyrochlore oxide - Cm{sub 2}Zr{sub 2}O{sub 7} - is formed (a = 10.63 {+-}0.02 Angstrom). (author)

  13. 78 FR 73824 - Subzones 247A and 247B, Authorization of Production Activity, GE Transportation, (Locomotives...

    Science.gov (United States)

    2013-12-09

    ... of Production Activity, GE Transportation, (Locomotives, Off-Highway Vehicles and Motors/Engines), Lawrence Park and Grove City, Pennsylvania On July 18, 2013, GE Transportation submitted a notification of proposed production activity to the Foreign-Trade Zones (FTZ) Board for its facilities within Subzones 247A...

  14. Total and spontaneous fission half-lives of the americium and curium nuclides

    International Nuclear Information System (INIS)

    Holden, N.E.

    1984-01-01

    The total half-life and the half-life for spontaneous fission are evaluated for the various long-lived nuclides of interest. Recommended values are presented for 241 Am, /sup 242m/Am, 243 Am, 242 Cm, 243 Cm, 244 Cm, 245 Cm, 246 Cm, 247 Cm, 248 Cm, and 250 Cm. The uncertainties are provided at the 95% confidence limit for each of the recommended values

  15. Transport of plutonium, americium, and curium from soils into plants by roots

    International Nuclear Information System (INIS)

    Pimpl, M.; Schuettelkopf, H.

    1979-12-01

    For assessing the dose from radionuclides in agricultural products by ingestion it is necessary to know the soil to plant transfer factors. The literature was entirely investigated, in order to judge the size of the soil to plant transfer factors. In total, 92 publications - from 1948 to 1978 -have been evaluated. As result, transfer factors from 10 -9 to 10 -3 have been found for Plutonium, and from 10 -6 to 1 for Americium. For Curium only few data are available in literature. The considerable variation of the measured transfer factors is based on the dependence of these transfer factors from the ion exchange capacity of soils, from the amount of organic materials, from the pH-value, and from the mode of contamination. There are, in any case, contradictory data, although there has been detected a dependence of the transfer factors from these parameters. Chelating agenst increase the transfer factors to approximately 1300. As well, fertilizers have an influence on the size of the transfer factors - however, the relationships have been scarcely investigated. The distribution of actinides within the individual parts of plants has been investigated. The highest concentrations are in the roots; in the plant parts above ground the concentration of actinides decreases considerably. The most inferior transfer factors were measured for the respective seed or fruits. The soil to plant transfer factors of actinides are more dependend on the age of the plants within one growing period. At the beginning of the period, the transfer factor is considerably higher than at the end of this period. With respect to plants with a growing period of several years, correlations are unknown. (orig.) [de

  16. Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

    International Nuclear Information System (INIS)

    Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z.; Gillow, J.B.; Francis, A.J.

    2004-01-01

    We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K d ) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N H 2 O ) and the degree of strength of ligand field (R E/M ) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K d of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K d , indicating that an exchange with Na + on the functional groups was involved in their sorption. The ΔN H 2 O (= 9 - N H 2 O ) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R E/M for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

  17. Sorption behavior of europium(III) and curium(III) on the cell surfaces of microorganisms

    Energy Technology Data Exchange (ETDEWEB)

    Ozaki, T.; Kimura, T.; Ohnuki, T.; Yoshida, Z. [Advanced Science Research Center, Japan Atomic Energy Research Inst., Ibaraki (Japan); Gillow, J.B.; Francis, A.J. [Environmental Sciences Dept., Brookhaven National Lab., Upton, NY (United States)

    2004-07-01

    We investigated the association of europium(III) and curium(III) with the microorganisms Chlorella vulgaris, Bacillus subtilis, Pseudomonas fluorescens, Halomonas sp., Halobacterium salinarum, and Halobacterium halobium. We determined the kinetics and distribution coefficients (K{sub d}) for Eu(III) and Cm(III) sorption at pH 3-5 by batch experiments, and evaluated the number of water molecules in the inner-sphere (N{sub H{sub 2}O}) and the degree of strength of ligand field (R{sub E/M}) for Eu(III) by time-resolved laser-induced fluorescence spectroscopy (TRLFS). Exudates from C. vulgaris, Halomonas sp., and H. halobium had an affinity for Eu(III) and Cm(III). The log K{sub d} of Eu(III) and Cm(III) showed that their sorption was not fully due to the exchange with three protons on the functional groups on cell surfaces. The halophilic microorganisms (Halomonas sp., Halobacterium salinarum, H. halobium) showed almost no pH dependence in log K{sub d}, indicating that an exchange with Na{sup +} on the functional groups was involved in their sorption. The {delta}N{sub H{sub 2}O} (= 9 - N{sub H{sub 2}O}) for Eu(III) on C. vulgaris was 1-3, while that for the other microorganisms was over 3, demonstrating that the coordination of Eu(III) with C. vulgaris was predominantly an outer-spherical process. The R{sub E/M} for Eu(III) on halophilic microorganisms was 2.5-5, while that for non-halophilic ones was 1-2.5. This finding suggests that the coordination environment of Eu(III) on the halophilic microorganisms is more complicated than that on the other three non-halophilic ones. (orig.)

  18. Creep Behaviour of Modified Mar-247 Superalloy

    Directory of Open Access Journals (Sweden)

    Cieśla M.

    2016-06-01

    Full Text Available The paper presents the results of analysis of creep behaviour in short term creep tests of cast MAR-247 nickel-based superalloy samples made using various modification techniques and heat treatment. The accelerated creep tests were performed under temperature of 982 °C and the axial stresses of σ = 150 MPa (variant I and 200 MPa (variant II. The creep behaviour was analysed based on: creep durability (creep rupture life, steady-state creep rate and morphological parameters of macro- and microstructure. It was observed that the grain size determines the creep durability in case of test conditions used in variant I, durability of coarse-grained samples was significantly higher.

  19. Behavior of americium, curium, and certain fission products in fluoride melts in the presence of s olid extraction agents

    International Nuclear Information System (INIS)

    Alekseev, V.A.; Klokman, V.R.; Morozova, Z.E.; Ziv, V.S.

    1986-01-01

    The authors consider the behavior of americium, curium, and certain fission products (europium, cerium, yttrium, and strontium) in fluoride and chlode-fluoride melts in the presence of nonisomorphous solid phases: calcium fluoride and lanthanum and zirconium oxides. It is shown that the trace components enter the solid calcium fluoride in a regular fashion only in the presence of an adequate amount of oxygen in the melt. The effect of oxygen on the coprecipitation with calcium fluoride occurs because oxygen compounds of the elements must be formed in the melt, and these are then coprecipitated with the calcium fluoride

  20. The effect of temperature on the sorption of technetium, uranium, neptunium and curium on bentonite, tuff and granodiorite

    International Nuclear Information System (INIS)

    Baston, G.M.N.; Berry, J.A.; Brownsword, M.; Heath, T.G.; Ilett, D.J.; Tweed, C.J.; Yui, M.

    1997-01-01

    A study of the sorption of the radioelements technetium; uranium; neptunium; and curium onto geological materials has been carried out as part of the PNC program to increase confidence in the performance assessment for a high-level radioactive waste repository in Japan. Batch sorption experiments have been performed in order to study the sorption of the radioelements onto bentonite, tuff and granodiorite from equilibrated de-ionized water under strongly-reducing conditions at both room temperature and at 60 C. Mathematical modelling using the geochemical speciation program HARPHRQ in conjunction with the HATCHES database has been undertaken in order to interpret the experimental results

  1. Determination of americium and curium using ion-exchange in the nitric-acid-methanol medium for environmental analysis

    International Nuclear Information System (INIS)

    Holm, E.; Fukai, R.

    1976-01-01

    While transplutonic elements are only slightly sorbed to anion exchangers from hydrochloric or nitric acid media, the presence of alcohol enhances the anionic exchange of these elements, especially in nitric and sulfuric solutions. In the present work a method has been developed for determining americium and curium in environmental samples, on the basis of the difference between the sorption characteristics to anion exchangers in the acid-methanol system of these transplutonic elements and those of plutonium, polonium and thorium. The method also permits us to perform sequential determination of plutonium, when necessary

  2. Safe handling of kilogram amounts of fuel-grade plutonium and of gram amounts of plutonium-238, americium-241 and curium-244

    International Nuclear Information System (INIS)

    Louwrier, K.P.; Richter, K.

    1976-01-01

    During the past 10 years about 600 glove-boxes have been installed at the Institute for Transuranium Elements at Karlsruhe. About 80% of these glove-boxes have been designed and equipped for handling 100-g to 1-kg amounts of 239 Pu containing 8-12% 240 Pu (low-exposure plutonium). A small proportion of the glove-boxes is equipped with additional shielding in the form of lead sheet or lead glass for work with recycled plutonium. In these glove-boxes gram-amounts of 241 Am have also been handled for preparation of Al-Am targets using tongs and additional shielding inside the glove-boxes themselves. Water- and lead-shielded glove-boxes equipped with telemanipulators have been installed for routine work with gram-amounts of 241 Am, 243 Am and 244 Cm. A prediction of the expected radiation dose for the personnel is difficult and only valid for a preparation procedure with well-defined preparation steps, owing to the fact that gamma dose-rates depend strongly upon proximity and source seize. Gamma radiation dose measurements during non-routine work for 241 Am target preparation showed that handling of gram amounts leads to a rather high irradiation dose for the personnel, despite lead or steel glove-box shielding and shielding within the glove-boxes. A direct glove-hand to americium contact must be avoided. For all glove-handling of materials with gamma radiation an irradiation control of the forearms of the personnel by, for example, thermoluminescence dosimeters is necessary. Routine handling of americium and curium should be executed with master-slave equipment behind neutron and gamma shielding. (author)

  3. Electrochemistry of oxygen-free curium compounds in fused NaCl-2CsCl eutectic

    International Nuclear Information System (INIS)

    Osipenko, A.; Maershin, A.; Smolenski, V.; Novoselova, A.; Kormilitsyn, M.; Bychkov, A.

    2010-01-01

    This work presents the electrochemical study of Cm(III) in fused NaCl-2CsCl eutectic in the temperature range 823-1023 K. Transient electrochemical techniques such as cyclic, differential pulse and square wave voltammetry, and chronopotentiometry have been used in order to investigate the reduction mechanism of curium ions up to the metal. The results obtained show that the reduction reaction takes place in a single step Cm(III)+3e-bar →Cm(0). The diffusion coefficient of [CmCl 6 ] 3- complex ions was determined by cyclic voltammetry at different temperatures by applying the Berzins-Delahay equation. The validity of the Arrhenius law was also verified and the activation energy for diffusion was found to be 44.46 kJ/mol. The apparent standard electrode potential of the redox couple Cm(III)/Cm(0) was found by chronopotentiometry at several temperatures. The thermodynamic properties of curium trichloride have also been calculated.

  4. 48 CFR 3452.247-70 - Foreign travel.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 7 2010-10-01 2010-10-01 false Foreign travel. 3452.247-70 Section 3452.247-70 Federal Acquisition Regulations System DEPARTMENT OF EDUCATION ACQUISITION... travel” means travel outside the fifty States comprising the United States, the District of Columbia, and...

  5. 48 CFR 452.247-70 - Delivery Location.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Delivery Location. 452.247-70 Section 452.247-70 Federal Acquisition Regulations System DEPARTMENT OF AGRICULTURE CLAUSES AND... Location. As prescribed in 447.302, insert a clause substantially as follows: Delivery Location (FEB 1988...

  6. Formation and characterization of Y : 247 film through spray ...

    Indian Academy of Sciences (India)

    Unknown

    gions (< 50 Å) of minority Y : 124 phase and stacking faults capable of ... critical current density (Jc) for Y : 247 films is ~ 103 A/cm2, and with silver ..... biphasic. As a result of decomposition, Y : 247 may be partially converted into Y : 124.

  7. 48 CFR 952.247-70 - Foreign travel.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Foreign travel. 952.247-70... SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 952.247-70 Foreign travel. As prescribed in 947.7002, insert the following clause: Foreign Travel (JUN 2010) Contractor foreign travel...

  8. 47 CFR 24.247 - Triggering a reimbursement obligation.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Triggering a reimbursement obligation. 24.247... Mhz Band § 24.247 Triggering a reimbursement obligation. (a) Licensed PCS. The clearinghouse will... the Proximity Threshold test indicates that a reimbursement obligation exists, the clearinghouse will...

  9. 40 CFR 247.10 - Paper and paper products.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Paper and paper products. 247.10... COMPREHENSIVE PROCUREMENT GUIDELINE FOR PRODUCTS CONTAINING RECOVERED MATERIALS Item Designations § 247.10 Paper and paper products. Paper and paper products, excluding building and construction paper grades. ...

  10. 48 CFR 52.247-7 - Freight Excluded.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Freight Excluded. 52.247-7... AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 52.247-7 Freight... contracts for transportation or for transportation-related services when any commodities or types of...

  11. Experimental and in situ investigations on americium, curium and plutonium behaviour in marine benthic species: transfer from water or sediments

    International Nuclear Information System (INIS)

    Miramand, P.

    1984-06-01

    The tranfer of transuranic elements -americium, curium and plutonium- from the sediments containing them to some marine benthic species (endofauna and epifauna) was studied with a twofold approach - laboratory and in-situ investigation. The experimental investigations, divided into three parts, made it possible to specify concentration factors (F.C.), transfer factors (F.T.) and to understand the process involved for 5 benthic species. The result were refined by an in-situ study that brought new data on the marine distribution of the transuranic elements released by the La Hague plant. Finally, the localization of americium and plutonium in the tissues and cells of these species was determined by autoradiography [fr

  12. Dicty_cDB: SHH247 [Dicty_cDB

    Lifescience Database Archive (English)

    Full Text Available SH (Link to library) SHH247 (Link to dictyBase) - - - Contig-U15693-1 - (Link to Or...iginal site) - - SHH247Z 601 - - - - Show SHH247 Library SH (Link to library) Clone ID SHH247 (Link to dicty...Base) Atlas ID - NBRP ID - dictyBase ID - Link to Contig Contig-U15693-1 Original site URL http://dictycdb.b...pdate 2002.12. 6 Homology vs DNA Score E Sequences producing significant alignments: (bits) Value N AF188717 |AF188717.1 Dict...ogaster SD01519 fu... 56 6e-07 DQ353802_1( DQ353802 |pid:none) Ictalurus punctatu

  13. 24/7 security system: 60-FPS color EMCCD camera with integral human recognition

    Science.gov (United States)

    Vogelsong, T. L.; Boult, T. E.; Gardner, D. W.; Woodworth, R.; Johnson, R. C.; Heflin, B.

    2007-04-01

    An advanced surveillance/security system is being developed for unattended 24/7 image acquisition and automated detection, discrimination, and tracking of humans and vehicles. The low-light video camera incorporates an electron multiplying CCD sensor with a programmable on-chip gain of up to 1000:1, providing effective noise levels of less than 1 electron. The EMCCD camera operates in full color mode under sunlit and moonlit conditions, and monochrome under quarter-moonlight to overcast starlight illumination. Sixty frame per second operation and progressive scanning minimizes motion artifacts. The acquired image sequences are processed with FPGA-compatible real-time algorithms, to detect/localize/track targets and reject non-targets due to clutter under a broad range of illumination conditions and viewing angles. The object detectors that are used are trained from actual image data. Detectors have been developed and demonstrated for faces, upright humans, crawling humans, large animals, cars and trucks. Detection and tracking of targets too small for template-based detection is achieved. For face and vehicle targets the results of the detection are passed to secondary processing to extract recognition templates, which are then compared with a database for identification. When combined with pan-tilt-zoom (PTZ) optics, the resulting system provides a reliable wide-area 24/7 surveillance system that avoids the high life-cycle cost of infrared cameras and image intensifiers.

  14. Is the chain of galaxies near NGC 247 anomalous

    International Nuclear Information System (INIS)

    Balkowski, C.; Chamaraux, P.

    1975-01-01

    Neutral hydrogen 21-cm observations of the chain of galaxies near NGC 247 are reported on. From HI and optical data, the chain's distance is found to be 62sub(-25)+- 41 Mpc, in agreement with the redshift. This result rules out Arp's assumption of a physical association between NGC 247 and the chain at a confidence level of better than 3.9 times the r.m.s. dispersion. The HI content of the chain is quite normal, and it is likely to be dynamically stable: these results would argue against the proposal made by Burbridge et al. that the chain was formed recently. (orig.) [de

  15. Radiation-chemical behaviour of neptunium ions in nitric acid solutions in the presence of curium-244

    International Nuclear Information System (INIS)

    Frolova, L.M.; Frolov, A.A.; Vasil'ev, V.Ya.

    1984-01-01

    Radiation-chemical behaviour of neptunium ions in nitric acid solutions is studied under the action of intensive internal alpha-irradiation conditioned by curium nuclides. In 0.3-1.1 mol/l solutions of nitric acid radiation-chemical oxidation of neptunium (4) and reduction of neptunium (6) is obeyed to the first order law of reaction rate in respect to neptunium concentration. Effective constants of neptunium (4) oxidation rates and neptuniumi(6) reduction rates are not dependent on neptunium ion in1tial concentration and increase with a growth of a dose rate of alpha-irradiation of solution. In equilibrium only neptunium (5) and neptunium (6) are present in solutions with HNO 3 concentration less than 1 mol/l. In more concentrated solutions equilibrium between sexa-, penta- and tetravalent neptunium forms is established. Equilibrium concentrations of neptunium valent forms are not dependent on neptunium initial oxidation state under the same initial conditions (dose rate, neptunium concentration and acidity. It is shown form experimental data that under the action of alpha-irradiation neptunium (5) both is oxidated to neptunium (6) and is reduced to neptunium (4)

  16. Use of radioanalytical methods for determination of uranium, neptunium, plutonium, americium and curium isotopes in radioactive wastes

    International Nuclear Information System (INIS)

    Geraldo, Bianca

    2012-01-01

    Activated charcoal is a common type of radioactive waste that contains high concentrations of fission and activation products. The management of this waste includes its characterization aiming the determination and quantification of the specific radionuclides including those known as Difficult-to-Measure Radionuclides (RDM). The analysis of the RDM's generally involves complex radiochemical analysis for purification and separation of the radionuclides, which are expensive and time-consuming. The objective of this work was to define a methodology for sequential analysis of the isotopes of uranium, neptunium, plutonium, americium and curium present in a type of radioactive waste, evaluating chemical yield, analysis of time spent, amount of secondary waste generated and cost. Three methodologies were compared and validated that employ ion exchange (TI + EC), extraction chromatography (EC) and extraction with polymers (ECP). The waste chosen was the activated charcoal from the purification system of primary circuit water cooling the reactor IEA-R1. The charcoal samples were dissolved by acid digestion followed by purification and separation of isotopes with ion exchange resins, extraction and chromatographic extraction polymers. Isotopes were analyzed on an alpha spectrometer, equipped with surface barrier detectors. The chemical yields were satisfactory for the methods TI + EC and EC. ECP method was comparable with those methods only for uranium. Statistical analysis as well the analysis of time spent, amount of secondary waste generated and cost revealed that EC method is the most effective for identifying and quantifying U, Np, Pu, Am and Cm present in charcoal. (author)

  17. 40 CFR 247.16 - Non-paper office products.

    Science.gov (United States)

    2010-07-01

    ... pressboard binders containing recovered paper; and solid plastic binders containing recovered plastic. (e... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Non-paper office products. 247.16...-paper office products. (a) Office recycling containers and office waste receptacles. (b) Plastic desktop...

  18. 48 CFR 52.247-6 - Financial Statement.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Financial Statement. 52....247-6 Financial Statement. As prescribed in 47.207-1(e), insert the following provision in... furnish financial statements: Financial Statement (APR 1984) The offeror shall, upon request, promptly...

  19. 14 CFR 135.247 - Pilot qualifications: Recent experience.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Pilot qualifications: Recent experience... Flight Crewmember Requirements § 135.247 Pilot qualifications: Recent experience. (a) No certificate holder may use any person, nor may any person serve, as pilot in command of an aircraft carrying...

  20. 48 CFR 52.247-28 - Contractor's Invoices.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Contractor's Invoices. 52....247-28 Contractor's Invoices. As prescribed in 47.207-9(c), insert the following clause in... services: Contractor's Invoices (APR 1984) The Contractor shall submit itemized invoices as instructed by...

  1. CDC 24/7: Saving Lives, Protecting People

    Centers for Disease Control (CDC) Podcasts

    2012-06-04

    24/7, CDC provides health information, responds to public health emergencies and natural disasters, and monitors disease.  Created: 6/4/2012 by Office of the Associate Director of Communciation (OADC).   Date Released: 6/4/2012.

  2. 48 CFR 52.247-51 - Evaluation of Export Offers.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Evaluation of Export....247-51 Evaluation of Export Offers. As prescribed in 47.305-6(e), insert the following provision: Evaluation of Export Offers (JAN 2001) (a) Port handling and ocean charges—other than DOD water terminals...

  3. 48 CFR 247.370 - DD Form 1384, Transportation Control and Movement Document.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false DD Form 1384, Transportation Control and Movement Document. 247.370 Section 247.370 Federal Acquisition Regulations System... Transportation in Supply Contracts 247.370 DD Form 1384, Transportation Control and Movement Document. The...

  4. 48 CFR 52.247-67 - Submission of Transportation Documents for Audit.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Submission of Transportation Documents for Audit. 52.247-67 Section 52.247-67 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION (CONTINUED) CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 52.247-67 Submission...

  5. Determination of C0-60 in Cobalt Slugs and Slabs and Radionuclides in Curium Sampler Slugs L-Reactor Disassembly Basin

    International Nuclear Information System (INIS)

    Casella, V.R.

    2004-01-01

    Co-60 was historically produced in the SRS reactors. Cobalt slugs were irradiated in the early 1970s. Post-production, remaining cobalt slugs (including slab form) were consolidated for storage. There are approximately nine hundred cobalt slugs currently stored awaiting final disposition. These slugs had historically incomplete documentation for activity rates; therefore, assaying was required in order to determine their activity levels. Since the gamma dose rate from these slugs is extremely high, the most cost effective way to shield a source of this magnitude from personnel and the radiation detector was to use the basin water in which the slugs are stored as the shield. A sodium iodide gamma detector was placed above a specially designed air collimator assembly, so that slug was at least eight feet from the detector and was shielded by the basin water. Using a sodium iodide detector and multichannel analyzer system and an underwater collimator assembly, Co-60 concentrations we re determined for Disassembly Basin cobalt slugs and slabs and 18 curium sampler slugs. The total activity of all of the assayed slugs summed to 31,783 curies. From the Co-60 concentrations of the curium sampler slugs, the irradiation flux was determined for the known irradiation time. The amounts of Pu-238, 239, 240, 241, 242; Am-241, 243; and Cm-242, 244 produced were then obtained based on the original amount of Pu-239 irradiated

  6. Co-ordination properties of diglycol-amide (DGA) to trivalent curium and lanthanides studied by XAS, XRD and XPS methods

    International Nuclear Information System (INIS)

    Yaita, T.; Hirata, M.; Narita, H.; Tachimori, S.; Yamamoto, H.; Edelstein, N.M.; Bucher, J.J.; Shuh, D.K.; Rao, L.

    2001-01-01

    Co-ordination properties of diglycol-amide (DGA) to trivalent curium and to the trivalent lanthanides were studied by the EXAFS, the XRD and the XPS methods. The structural determinations by both the crystal XRD and the solution EXAFS methods showed that the DGA co-ordinated to the trivalent lanthanide ion in a tridentate fashion: co-ordination of three oxygen atoms of each ligand to the metal ion. The bond distances of Er-O (carbonyl) and Er-O (ether) in the Er-DGA complex were 2.35 Angstrom, and 2.46 Angstrom, respectively, while the atom distances of Cm-O (carbonyl) and Cm-O (ether) in the Cm-DGA complex were 2.42 Angstrom and 3.94 Angstrom, respectively from the EXAFS data for the Cm-DGA complex. Accordingly, the DGA would behave only as a semi-tridentate in the co-ordination to trivalent curium in solution. We determined the valence band structures of the Er-DGA complex by the XPS in order to clarify the bond properties of the complex, and assigned the XPS spectrum by using the DV-DS molecular orbital calculation method. (authors)

  7. 24/7 pediatric radiology attending coverage: times are changing

    Energy Technology Data Exchange (ETDEWEB)

    Donaldson, James S. [Feinberg School of Medicine at Northwestern University, Department of Medical Imaging, Ann and Robert H. Lurie Children' s Hospital of Chicago, IL (United States); Thakrar, Kiran H. [University of Chicago Pritzker School of Medicine, Body Imaging, NorthShore University HealthSystem, Chicago, IL (United States)

    2017-06-15

    The job of the pediatric radiologist long ago ceased to be an 8-to-5 role. Many practices have adopted evening shifts of in-house attending radiologists to cover the busy evening activity. With the ever-increasing role of imaging in clinical decisions and patient management, there is a need - if not a demand - to further extend attending pediatric radiology coverage. In this article, we discuss the needs and justification for extending pediatric radiology coverage at a tertiary-care children's hospital. We also describe the approach we took toward implementing 24/7 attending in-house coverage of pediatric radiology. (orig.)

  8. Thermodynamics of curium(III) in concentrated electrolyte solutions: formation of sulfate complexes in NaCl/Na2SO4 solutions

    International Nuclear Information System (INIS)

    Paviet, P.; Fanghaenel, T.; Klenze, R.; Kim, J.I.

    1996-01-01

    The formation of sulfate complexes of Curium in aqueous solutions is studied by time resolved laser fluorescence spectroscopy (TRLFS) at 25 C. The species Cm 3+ , Cm(SO 4 ) - , Cm(SO 4 ) - 2 and Cm(SO 4 ) 3- 3 are quantified spectroscopically in the trace concentration range by peak deconvolution of fluorescence emission spectra. The complex formation equilibria are measured in NaCl/ Na 2 SO 4 solutions of constant ionic strength (3 molal) as a function of the sulfate concentration. The stability constants of Cm(SO 4 ) + and Cm(SO 4 ) - 2 are determined to be log β 1 = 0.93±0.08 and log β 2 = 0.61±0.08, respectively. The complex Cm(SO 4 ) 3- 3 is found to be stable only at very high sulfate concentrations (above 1 molal) and therefore not considered for further evaluation. (orig.)

  9. Spectroscopic and thermodynamic studies on the complexation of trivalent curium with inorganic ligands at increased temperatures; Spektroskopische und thermodynamische Untersuchungen zur Komplexierung von trivalentem Curium mit anorganischen Liganden bei erhoehten Temperaturen

    Energy Technology Data Exchange (ETDEWEB)

    Skerencak, Andrej

    2010-05-11

    The subject of the present investigation is the complexation of trivalent actinides at elevated temperatures. The objective of this work is to broaden the comprehension of the geochemical processes relevant for the migration of radionuclides in the near-field of a nuclear waste repository. Depending on the disposed nuclear waste, the temperature in the direct vicinity of a nuclear waste repository may reach up to 200 C. The result is a distinct change of the geochemistry of the actinides. Many of these processes have already been studied in detail at room temperature. Yet, data at elevated temperature are rare. However, a comprehensive long term safety analysis of a nuclear waste repository requires the precise thermodynamic description of the relevant geochemical processes at room as well as at elevated temperatures. The present work is focused on the investigation of the complexation of trivalent curium (Cm(III)) with different inorganic ligands at elevated temperatures. Due to its outstanding spectroscopic properties, Cm(III) is chosen as a representative for trivalent actinides. The studied ligand systems are nitrate (NO{sub 3}{sup -}), fluoride (F{sup -}), sulphate (SO{sub 4}{sup 2-}) and chloride (Cl{sup -}). The main analytical method employed is the ''time resolved laser fluorescence spectroscopy'' (TRLFS). The experiments with nitrate, sulphate and chloride were carried out in a custom-built high temperature cell, enabling spectroscopic studies at temperatures up to 200 C. The Cm(III)-fluoride-system was studied in a cuvette (quartz glass) in the temperature range from 20 to 90 C. Supplementary structural studies were performed using EXAFS (Extended X-Ray Absorption Fine Structure) spectroscopy and supported by quantum chemical calculations at DFT (Density Functional Theory) level. The results of the TRLFS studies show a general shift of the chemical equilibrium towards the complexed species with increasing temperature. For instance

  10. 32 CFR Appendix E to Part 247 - DoD Command Newspaper and Magazine Review System

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 2 2010-07-01 2010-07-01 false DoD Command Newspaper and Magazine Review System... OF DEFENSE (CONTINUED) MISCELLANEOUS DEPARTMENT OF DEFENSE NEWSPAPERS, MAGAZINES AND CIVILIAN ENTERPRISE PUBLICATIONS Pt. 247, App. E Appendix E to Part 247—DoD Command Newspaper and Magazine Review...

  11. The recycling of the actinides neptunium, americium and curium in a fast power reactor to reduce the long term activity in a final store

    International Nuclear Information System (INIS)

    Beims, H.D.

    1986-01-01

    The starting point for the considerations and calculations given in this dissertation is the inevitable production of radioactive materials in the use of nuclear energy, which creates a considerable potential danger in a final store for a very long period. As one possibility of alleviating this problem, a concept for recycling the waste actinides neptunium, americium and curium was proposed. The waste actinides are separated in the reprocessing of burnt-up fuel elements and reach a further irradiation circuit. There they pass through the stages 'manufacture of irradiation elements', 'use in a fast power reactor' and reprocessing of irradiation elements' several times. In each irradiation and subsequent storage, about 17% of the waste actinides are removed by fission or by conversion into nuclides which can be reused as fuel, so that during the life of 40 years of the fast recycling reacor, the waste actinides can be reduced in mass by one half. In order to determine this mass reduction effect, a model calculation was developed, which includes the representation of the neutron physics and thermal properties of the reactor core and the storage and reprocessing of the irradiation elements. (orig./RB) [de

  12. Type B accident investigation board report of the July 2, 1997 curium intake by shredder operator at Building 513 Lawrence Livermore National Laboratory, Livermore, California. Final report

    International Nuclear Information System (INIS)

    1997-08-01

    On July 2, 1997 at approximately 6:00 A.M., two operators (Workers 1 and 2), wearing approved personal protective equipment (PPE), began a shredding operation of HEPA filters for volume reduction in Building 513 (B-513) at Lawrence Livermore National Laboratory (LLNL). The waste requisitions indicated they were shredding filters containing ≤ 1 μCi of americium-241 (Am-241). A third operator (Worker 3) provided support to the shredder operators in the shredding area (hot area) from a room that was adjacent to the shredding area (cold area). At Approximately 8:00 A.M., a fourth operator (Worker 4) relieved Worker 2 in the shredding operation. Sometime between 8:30 A.M. and 9:00 A.M., Worker 3 left the cold area to make a phone call and set off a hand and foot counter in Building 514. Upon discovering the contamination, the shredding operation was stopped and surveys were conducted in the shredder area. Surveys conducted on the workers found significant levels of contamination on their PPE and the exterior of their respirator cartridges. An exit survey of Worker 1 was conducted at approximately 10:05 A.M., and found contamination on his PPE, as well as on the exterior and interior of his respirator. Contamination was also found on his face, chest, back of neck, hair, knees, and mustache. A nose blow indicated significant contamination, which was later determined to be curium-244

  13. Radiology 24/7 In-House Attending Coverage: Do Benefits Outweigh Cost?

    Science.gov (United States)

    Coleman, Stephanie; Holalkere, Nagaraj Setty; O׳Malley, Julie; Doherty, Gemma; Norbash, Alexander; Kadom, Nadja

    2016-01-01

    Many radiology practices, including academic centers, are moving to in-house 24/7 attending coverage. This could be costly and may not be easily accepted by radiology trainees and attending radiologists. In this article, we evaluated the effects of 24/7 in-house attending coverage on patient care, costs, and qualitative aspects such as trainee education. We retrospectively collected report turnaround times (TAT) and work relative value units (wRVU). We compared these parameters between the years before and after the implementation of 24/7 in-house attending coverage. The cost to provide additional attending coverage was estimated from departmental financial reports. A qualitative survey of radiology residents and faculty was performed to study perceived effects on trainee education. There were decreases in report TAT following 24/7 attending implementation: 69% reduction in computed tomography, 43% reduction in diagnostic radiography, 7% reduction in magnetic resonance imaging, and 43% reduction in ultrasound. There was an average daytime wRVU decrease of 9%, although this was compounded by a decrease in total RVUs of the 2013 calendar year. The financial investment by the institution was estimated at $850,000. Qualitative data demonstrated overall positive feedback from trainees and faculty in radiology, although loss of independence was reported as a negative effect. TAT and wRVU metrics changed with implementation of 24/7 attending coverage, although these metrics do not directly relate to patient outcomes. Additional clinical benefits may include fewer discrepancies between preliminary and final reports that may improve emergency and inpatient department workflows and liability exposure. Radiologists reported the impression that clinicians appreciated 24/7 in-house attending coverage, particularly surgical specialists. Loss of trainee independence on call was a perceived disadvantage of 24/7 attending coverage and raised a concern that residency education

  14. Determination of Neptunium, Americium and Curium in Spent Nuclear Fuel Samples by Alpha Spectrometry Using 239Np and 243Am as a Spike and a Tracer

    International Nuclear Information System (INIS)

    Jeo, Kih-Soo; Song, Byung-Chul; Kim, Young-Bok; Han, Sun-Ho; Jeon, Young-Shin; Jung, Euo-Chang; Jee, Kwang-Yong

    2007-01-01

    Determination of actinide elements and fission products in spent nuclear fuels is of importance for a burnup determination and source term evaluation. Especially, the amounts of uranium and plutonium isotopes are used for the evaluation of a burnup credit in spent nuclear fuels. Additionally, other actinides such as Np, Am and Cm in spent nuclear fuel samples is also required for the purposes mentioned above. In this study, 237 Np, 241 Am and 244 Cm were determined by an alpha spectrometry for the source term data for high burnup spent nuclear fuels ranging from 37 to 62.9 GWD/MtU as a burnup. Generally, mass spectrometry has been known as the most powerful method for isotope determinations such as high concentrations of uranium and plutonium. However, in the case of minor actinides such as Np, Am and Cm, alpha spectrometry would be recommended instead. Determination of the transuranic elements in spent nuclear fuel samples is different from that for environmental samples because the amount of each nuclide in the spent fuel samples is higher and the relative ratios between each nuclide are also different from those for environmental samples. So, it is important to select an appropriate tracer and an optimum sample size depending on the nuclides and analytical method. In this study 237 Np was determined by an isotope dilution alpha(gamma) spectrometry using 239 Np as a spike, and 241 Am and curium isotopes were determined by alpha spectrometry using 243 Am as a tracer. The content of each nuclide was compared with that by the Origen-2 code

  15. Electric resistivity of 241-americium and 244-curium metals. Creation of defects and isochronous annealing of 241-americium metal after self-irradiation

    International Nuclear Information System (INIS)

    Schenkel, R.

    1977-03-01

    The temperature dependence of the electrical resistivity of thin films of bulk 241 Am metal were measured between 300 and 4.5 K. The room temperature resistivity was found to be 68.90μΩcm. At room temperature the electrical resistivity of americium increases with pressure (3% up to 13 kbar). The application of 13 kbar pressure did not change the low temperature power law in the electrical resistivity. The resistivity vs temperature curve can be explained by assuming s-d scattering of conduction electrons. The localized 5f electrons are considered to be about 5eV below the Fermi level. Americium therefore should be the first lanthanide-like element in the actinide series. The defect production due to self-irradiation damage was studied by measuring the increase of the resistivity at 4.2 K over a period of 738 h. A saturation resistivity of 16.036 μΩcm was found corresponding to a defect concentration of about 0.22 a/o. After isochronal annealing two recovery stages were observed at about 65 and 145 K. The two stages shift with increasing initial defect concentration to lower temperatures. Estimates of the activation energies and the reaction order were made and possible defect reactions suggested. The magnetic contribution to the electrical resistivity of curium, which shows an antiferromagnetic transition at 52.5 k, was obtained by subtracting the resistivity of americium (to be considered as phonon part). Comparison with theoretical models were made. At low temperatures the measurements are strongly affected by self-irradiation damage [drho/dt(t=0)=9.8μΩcm/h

  16. Separation and activity determination of 239+240Pu, 241Am and Curium (242and244Cm) in evaporator concentrate by Alpha Spectrometry

    International Nuclear Information System (INIS)

    Reis Junior, Aluisio S.; Temba, Eliane S.C.; Kastner, Geraldo F.; Monteiro, Roberto P.G.

    2013-01-01

    Alpha spectrometry analysis was used for activity determinations of Pu, Am and Cm isotopes in evaporator concentrate samples from nuclear power plants. Using a sequential procedure the first step was Pu isolation by an anion exchange column followed by an Am and Cm separation of U and Fe by a co-precipitation with oxalic acid. The precipitate was used for americium and curium separation of strontium by using a TRU resin extraction chromatography column. Due to their chemical similarities and energy difference it was seen that the simultaneous determination of 241 Am, 242 Cm and 24 3 ,244 Cm isotopes is possible using the 243 Am as tracer, once they have peaks in different region of interest (ROI) in the alpha spectrum. In this work it was used tracers, 238 Pu, 243 Am, 244 Cm and 232 U, for determination and quantification of theirs isotopes, respectively. The standard deviations for replicate analysis were calculated and for 241 Am it was (1,040 ± 160 mBqKg -1 ), relative standard deviation 15.38%, and for 239+240 Pu it was (551 +- 44 mBqKg -1 ), relative standard deviation 7.98%. In addition, for the 242 Cm isotope the standard deviation for determinations was(75 ± 23 mBqKg -1 ), with the relative standard deviation 30.67% higher than for 241 Am and 239+240 Pu. The radiometric yields ranged from 90% to 105% and the lower limit of detection was estimated as being 2.05 mBqKg -1 . (author)

  17. Switching Investigations on a SiC MOSFET in a TO-247 Package

    DEFF Research Database (Denmark)

    Anthon, Alexander; Hernandez Botella, Juan Carlos; Zhang, Zhe

    2014-01-01

    This paper deals with the switching behavior of a SiC MOSFET in a TO-247 package. Based on simulations, critical parasitic inductances in the circuit layout are analyzed and their effect on the switching losses highlighted. Especially the common source inductance, a critical parameter in a TO-247...... package, has a major influence on the switching energy. Crucial design guidelines for an improved double pulse test circuit are introduced which are used for practical investigations on the switching behavior. Switching energies of a SiC MOSFET in a TO-247 package is measured depending on varying gate...... resistance and loop inductances. With total switching energy of 340.24 μJ, the SiC MOSFET has more than six times lower switching losses than a regular Si IGBT. Implementing the SiC switches in a 3 kW T-Type inverter topology, efficiency improvements of 0.8 % are achieved and maximum efficiency of 97...

  18. Rotational emission-line spectrum of Orion A between 247 and 263 GHZ

    International Nuclear Information System (INIS)

    Blake, G.A.; Sutton, E.C.; Masson, C.R.; Phillips, T.G.

    1986-01-01

    Results are presented from a molecular line survey of the core of the Orion molecular cloud between 247 and 263 GHz. The spectrum contains a total of 243 resolvable lines from 23 different chemical species. When combined with the earlier survey of Orion from 215 to 247 GHz by Sutton et al (1985), the complete data set includes over 780 emission features from 29 distinct molecules. Of the 23 molecules detected in this survey, only NO, CCH, and HCO + were identified not in the lower frequency data

  19. 7 CFR 247.24 - Recovery and redistribution of caseload and administrative funds.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Recovery and redistribution of caseload and...) FOOD AND NUTRITION SERVICE, DEPARTMENT OF AGRICULTURE CHILD NUTRITION PROGRAMS COMMODITY SUPPLEMENTAL FOOD PROGRAM § 247.24 Recovery and redistribution of caseload and administrative funds. (a) May FNS...

  20. 7 CFR 247.23 - State provision of administrative funds to local agencies.

    Science.gov (United States)

    2010-01-01

    ... funds will be used to achieve program objectives. (Approved by the Office of Management and Budget under... 7 Agriculture 4 2010-01-01 2010-01-01 false State provision of administrative funds to local... PROGRAM § 247.23 State provision of administrative funds to local agencies. (a) How much of the...

  1. 7 CFR 247.13 - Provisions for non-English or limited-English speakers.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Provisions for non-English or limited-English speakers... § 247.13 Provisions for non-English or limited-English speakers. (a) What must State and local agencies do to ensure that non-English or limited-English speaking persons are aware of their rights and...

  2. 48 CFR 247.371 - DD Form 1653, Transportation Data for Solicitations.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false DD Form 1653... Supply Contracts 247.371 DD Form 1653, Transportation Data for Solicitations. The transportation specialist prepares the DD Form 1653 to accompany requirements for the acquisition of supplies. The completed...

  3. 48 CFR 247.372 - DD Form 1654, Evaluation of Transportation Cost Factors.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false DD Form 1654, Evaluation... Transportation in Supply Contracts 247.372 DD Form 1654, Evaluation of Transportation Cost Factors. Contracting personnel may use the DD Form 1654 to furnish information to the transportation office for development of...

  4. 75 FR 62333 - Airworthiness Directives; Hamilton Sundstrand Propellers Model 247F Propellers

    Science.gov (United States)

    2010-10-08

    ...., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory... that the 247F propeller blades, P/N 817370-1, S/Ns FR2449 to FR2958 inclusive, FR20010710 to FR20010722 inclusive, and FR20010723RT to FR20020127RT inclusive, manufactured since January 1999, might also have...

  5. Serving culturally diverse learners in the 24/7 management classroom

    NARCIS (Netherlands)

    van de Bunt-Kokhuis, S.G.M.; Weir, D.

    2013-01-01

    Purpose: The purpose of this paper is to highlight how future teaching in business schools will probably take place in an online (here called 24/7) classroom, where culturally diverse e-learners around the globe meet. Technologies such as iPhone, iPad and a variety of social media, to mention but a

  6. Prevalence of Plasmodium vivax VK210 and VK247 subtype in Myanmar

    Directory of Open Access Journals (Sweden)

    Kang Yoon-Joong

    2010-07-01

    Full Text Available Abstract Background Plasmodium vivax is divided into two subtypes, a dominant form, VK210 and a variant form, VK247. This division is dependent on the amino acid composition of the circumsporozoite (CS protein. In this study, the prevalence of the VK247 variant form of P. vivax was investigated in Myanmar. Methods The existence of malaria parasites in blood samples was determined by microscopic examination, polymerase chain reaction (PCR and DNA hybridization assays. To test for antibodies against P. vivax and Plasmodium falciparum in blood samples, an indirect immunofluorescence antibody test (IFAT was performed using asexual blood antigens. An enzyme-linked immunosorbent assay with synthetic VK210 and VK247 antigens was carried out to discriminate between the P. vivax subtypes. Results By thick smear examination, 73 (n = 100 patients were single infected with P. vivax, one with P. falciparum and 13 with both species. By thin smear, 53 patients were single infected with P. vivax, eight with only P. falciparum and 16 with both. Most of the collected blood samples were shown to be P. vivax positive (n = 95 by PCR. All cases that were positive for P. falciparum by PCR (n = 43 were also positive for P. vivax. However, 52 cases were single infected with P. vivax. IFAT showed antibody titres from 1:32 to 1:4,096. Additionally, using specific antibodies for VK210 and VK247, ELISA showed that 12 patients had antibodies for only the VK210 subtype, 4 patients had only VK247 subtype antibodies and 21 patients had antibodies for both subtypes. Using a DNA hybridization test, 47 patients were infected with the VK210 type, one patient was infected with VK247 and 23 patients were infected with both subtypes. Conclusions The proportion of the VK247 subtype in Myanmar was 43.1% (n = 25 among 58 positive cases by serodiagnosis and 25.6% (n = 24 among 94 positive cases by genetic diagnosis. In both diagnostic methods, the infection status of malaria patients is

  7. 48 CFR 252.247-7026 - Evaluation Preference for Use of Domestic Shipyards-Applicable to Acquisition of Carriage by...

    Science.gov (United States)

    2010-10-01

    ... AND CONTRACT CLAUSES Text of Provisions And Clauses 252.247-7026 Evaluation Preference for Use of... Noncontiguous Trade. As prescribed in 247.574(e), use the following provision: Evaluation Preference For Use of... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Evaluation Preference for...

  8. 17 CFR 247.700 - Defined terms relating to the networking exception from the definition of “broker.”

    Science.gov (United States)

    2010-04-01

    ... the average of the minimum and maximum hourly wage established by the bank for the current or prior... networking exception from the definition of âbroker.â 247.700 Section 247.700 Commodity and Securities Exchanges SECURITIES AND EXCHANGE COMMISSION (CONTINUED) REGULATION R-EXEMPTIONS AND DEFINITIONS RELATED TO...

  9. Analysis of the Neutron Generator and Target for the LSDTS System

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chang Je; Lee, Yong Deok; Song, Jae Hoon; Song, Kee Chan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2008-11-15

    A preliminary analysis was performed based on the literatures and the patents for the neutron generators and targets for the lead slowing down time spectrometer (LSDTS) system. It was found that local neutron generator did not exhibit enough neutron intensity such as 1E+12 n/s, which is a minimum requirement for the LSDTS system to overcome curium backgrounds. However, a neutron generator implemented with an electron accelerator may provide a higher intensity around 1E+13 n/s and it is required to investigate further including a detail analysis. In addition to the neutron generator, a study on target was performed with the Monte Carlo simulation. In the study, an optimal design of target was suggested to provide a high neutron yield and a better thermal resistance. The suggested target consists several cylindrical plates with a certain cooling gap, which have increasing thickness and increasing radius.

  10. Nursing staffs self-perceived outcome from a rehabilitation 24/7 educational programme - a mixed-methods study in stroke care.

    Science.gov (United States)

    Loft, M I; Esbensen, B A; Kirk, K; Pedersen, L; Martinsen, B; Iversen, H; Mathiesen, L L; Poulsen, I

    2018-01-01

    During the past two decades, attempts have been made to describe nurses' contributions to the rehabilitation of inpatients following stroke. There is currently a lack of interventions that integrate the diversity of nurses' role and functions in stroke rehabilitation and explore their effect on patient outcomes. Using a systematic evidence- and theory-based design, we developed an educational programme, Rehabilitation 24/7, for nursing staff working in stroke rehabilitation aiming at two target behaviours; working systematically with a rehabilitative approach in all aspects of patient care and working deliberately and systematically with patients' goals. The aim of this study was to assess nursing staff members' self-perceived outcome related to their capability, opportunity and motivation to work with a rehabilitative approach after participating in the stroke Rehabilitation 24/7 educational programme. A convergent mixed-method design was applied consisting of a survey and semi-structured interviews. Data collection was undertaken between February and June 2016. Data from the questionnaires ( N  = 33) distributed before and after the intervention were analysed using descriptive statistics and Wilcoxon sign rank test. The interviews ( N  = 10) were analysed using deductive content analysis. After analysing questionnaires and interviews separately, the results were merged in a side by side comparison presented in the discussion. The results from both the quantitative and qualitative analyses indicate that the educational programme shaped the target behaviours that we aimed to change by addressing the nursing staff's capability, opportunity and motivation and hence could strengthen the nursing staff's contribution to inpatient stroke rehabilitation. A number of behaviours changed significantly, and the qualitative results indicated that the staff experienced increased focus on their role and functions in rehabilitation practice. Our study provides an

  11. Magnetic susceptibility of curium pnictides

    International Nuclear Information System (INIS)

    Nave, S.E.; Huray, P.G.; Peterson, J.R.; Damien, D.A.; Haire, R.G.

    1981-09-01

    The magnetic susceptibility of microgram quantities of 248 CmP and 248 CmSb has been determined with the use of a SQUID micromagnetic susceptometer over the temperature range 4.2 to 340 K and in the applied magnetic field range of 0.45 to 1600 G. The fcc (NaCl-type) samples yield magnetic transitions at 73K and 162 K for the phosphide and antimonide, respectively. Together with published magnetic data for CmN and CmAs, these results indicate spatially extended exchange interactions between the relatively localized 5f electrons of the metallic actinide atoms

  12. Microstructural studies of carbides in MAR-M247 nickel-based superalloy

    Science.gov (United States)

    Szczotok, A.; Rodak, K.

    2012-05-01

    Carbides play an important role in the strengthening of microstructures of nickel-based superalloys. Grain boundary carbides prevent or retard grain-boundary sliding and make the grain boundary stronger. Carbides can also tie up certain elements that would otherwise promote phase instability during service. Various types of carbides are possible in the microstructure of nickel-based superalloys, depending on the superalloy composition and processing. In this paper, scanning electron and scanning transmission electron microscopy studies of carbides occurring in the microstructure of polycrystalline MAR-M247 nickel-based superalloy were carried out. In the present work, MC and M23C6 carbides in the MAR-M247 microstructure were examined.

  13. Evaluation of Cm-247 neutron cross sections in the resonance region

    International Nuclear Information System (INIS)

    Martinelli, T.; Menapace, E.; Motta, M.; Vaccari, M.

    1980-01-01

    The neutron cross sections of Cm-247 are evaluated in the resonance (resolved and unresolved) region up to 10 keV. Average resonance parameters (i.e. spacing D, fission and radiative widths, neutron strength functions) are determined for unresolved region calculations. Moreover for a better comparison with the experimental data, fission cross section is calculated up to 10 MeV. In addition, the average number of neutrons emitted per fission as a function of energy is estimated

  14. The energy and monetary implications of the '24/7 'always on' society

    International Nuclear Information System (INIS)

    Loveday, Dennis L.; Bhamra, T.; Tang, T.; Haines, V.J.A.; Holmes, M.J.; Green, R.J.

    2008-01-01

    This paper reviews the trends in society, technology and energy demand of the past 30 years, together with the growth of the 'on-demand' culture. The '24/7' or 'always on' society can be defined as one where people demand - and generally receive - what they want 'now'. It has grown up in parallel with developments in information technology, which have produced the services needed to meet that demand. Larger numbers of appliances, resulting from greater affluence and disposable income, have increased energy use, despite energy efficiencies in other areas. While monetary factors suggest that changes brought about by the 24/7 society will generally be self-correcting at the macro-economic level, there will nevertheless be effects for individuals, such as potentially severe impacts on the fuel poor as electricity prices rise. We conclude with a view of future directions. As the 24/7 culture continues to grow, there is scope for designers and for information technology to manage and reduce energy consumption. This includes buildings, their services systems, and the mix of new technologies that will be deployed over the next 20 years or so, including the possibilities for data exchange and control at the interface between energy suppliers and consumers, coupled with greater understanding of the behaviour of the consumers themselves. (author)

  15. Genetic Association of CD247 (CD3ζ) with SLE in a Large-Scale Multiethnic Study

    OpenAIRE

    Martins, Madalena; Williams, Adrienne H.; Comeau, Mary; Marion, Miranda; Ziegler, Julie T.; Freedman, Barry I.; Merrill, Joan T.; Glenn, Stuart B.; Kelly, Jennifer A.; Sivils, Kathy M.; James, Judith A.; Guthridge, Joel M.; Alarcón-Riquelme, Marta E.; Bae, Sang-Cheol; Kim, Jae-Hoon

    2015-01-01

    A classic T-cell phenotype in systemic lupus erythematosus (SLE) is the downregulation and replacement of the CD3ζ chain that alters T-cell receptor signaling. However, genetic associations with SLE in the human CD247 locus that encodes CD3ζ are not well established and require replication in independent cohorts. Our aim was therefore to examine, localize and validate CD247-SLE association in a large multiethnic population. We typed 44 contiguous CD247 single-nucleotide polymorphisms (SNPs) i...

  16. Project Plan Remote Target Fabrication Refurbishment Project

    International Nuclear Information System (INIS)

    Bell, Gary L.; Taylor, Robin D.

    2009-01-01

    was received in July 2009 under the Remote Target Fabrication Refurbishment Task of the Enhanced Utilization of Isotope Facilities project (Project Identification Code 2005230) funded by the American Recovery and Reinvestment Act of 2009. The goal of this project is to recover the capability to produce 4-5 curium targets for the irradiation period starting with HFIR cycle 427, currently scheduled to begin 2/17/10. Assuming success, the equipment would then be used to fabricate 6-7 additional targets to hold for the next irradiation campaign specified by the program. Specific objectives are the return to functionality of the Cubicle 3 Pellet Fabrication Line; Cubicle 2 Target Assembly equipment; and Cubicle 1 Target Inspection and Final Assembly system.

  17. Minor actinides transmutation scenario studies with PWRs, FRs and moderated targets

    International Nuclear Information System (INIS)

    Grouiller, J.P.; Pillon, S.; Saint Jean, C. de; Varaine, F.; Leyval, L.; Vambenepe, G.; Carlier, B.

    2003-01-01

    Using current technologies, we have demonstrated in this study that it is theoretically possible to obtain different minor actinide transmutation scenarios with a significant gain on the waste radiotoxicity inventory. The handling of objects with Am+Cm entails the significant increase of penetrating radiation sources (neutron and γ) whatever mixed scenario is envisioned; the PWR and FR scenario involving the recycling of Am + Cm in the form of targets results in the lowest flow. In the light of these outcomes, the detailed studies has allowed to design a target sub assembly with a high fission rate (90%) and define a drawing up of reprocessing diagram with the plant head, the minor actinide separation processes (PUREX, DIAMEX and SANEX). Some technological difficulties appear in manipulating curium, principally in manufacturing where the wet process ('sol-gel') is not acquired for (Am+Cm). (author)

  18. Extending Pickering Fuel Channel Life to 247,000 EFPH (2020)

    International Nuclear Information System (INIS)

    Malek, I.

    2013-01-01

    This presentation is about extending the life of PNGS Pressure tubes from 210,000 EFPH (Effective Full Power Hours) to 247,000 EFPH. The l license renewal is in 2013 (R & D defined in 2009). The unknowns are the extent of degradation in some key areas. There are regulatory requirements for fuel channel extended life. It is necessary to integrate inspection capability and do-ability in outages. This would result in safe operation and demonstrated margin to extend life with operation to 2020.

  19. High temperature creep properties of directionally solidified CM-247LC Ni-based superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Chiou, Mau-Sheng [Department of Materials Science and Engineering, I-Shou University, Kaohsiung 840, Taiwan (China); Jian, Sheng-Rui, E-mail: srjian@gmail.com [Department of Materials Science and Engineering, I-Shou University, Kaohsiung 840, Taiwan (China); Yeh, An-Chou [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 300, Taiwan (China); Kuo, Chen-Ming [Department of Mechanical and Automation Engineering, I-Shou University, Kaohsiung 840, Taiwan (China); Juang, Jenh-Yih [Department of Electrophysics, National Chiao Tung University, Hsinchu 300, Taiwan (China)

    2016-02-08

    This study explores the effects of cooling rate after solution heat treatment on the high temperature/low stress (982 °C/200 MPa) creep properties of CM-247LC Nickel base superalloy. Cooling rate was controlled by blowing argon gas, air cooling, and furnace cooling, which, in turn, gave rise to corresponding cooling rates (from 1260 °C to 800 °C) of 18.7, 7.4, and 0.19 °C/s, respectively. The results indicated that higher cooling rate from the solution heat treatment temperature led to finer γ′ precipitates and much improved tertiary creep as well as rupture life time in high-temperature creep test. The microstructural analyses using both scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that finer γ′ precipitates and narrower γ channel width could result in denser rafting structure which might have hindered the climb of dislocations across the precipitates rafts.

  20. Safe2Tell® : an anonymous, 24/7 reporting system for preventing school violence.

    Science.gov (United States)

    Payne, Susan R T; Elliott, Delbert S

    2011-01-01

    There is widespread agreement that many school shootings could be prevented if authorities were informed that a student was planning or preparing to carry out an attack. A universal problem is that young people are highly reluctant to report on their peers. This code of silence represents a major barrier to prevention efforts. In response to the Columbine shooting, the state of Colorado established the Safe2Tell® anonymous, 24/7 reporting system for receiving and forwarding threats of violence, bullying, and other concerns. This article describes how the program has grown to the point that it now receives more than 100 calls per month. A series of case examples illustrates its success in responding to threatening situations, including twenty-eight potential school attacks. Copyright © 2011 Wiley Periodicals, Inc., A Wiley Company.

  1. Use of radioanalytical methods for determination of uranium, neptunium, plutonium, americium and curium isotopes in radioactive wastes; Utilizacao de metodos radioanaliticos para a determinacao de isotopos de uranio, plutonio, americio e curio em rejeitos radioativos

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Bianca

    2012-07-01

    Activated charcoal is a common type of radioactive waste that contains high concentrations of fission and activation products. The management of this waste includes its characterization aiming the determination and quantification of the specific radionuclides including those known as Difficult-to-Measure Radionuclides (RDM). The analysis of the RDM's generally involves complex radiochemical analysis for purification and separation of the radionuclides, which are expensive and time-consuming. The objective of this work was to define a methodology for sequential analysis of the isotopes of uranium, neptunium, plutonium, americium and curium present in a type of radioactive waste, evaluating chemical yield, analysis of time spent, amount of secondary waste generated and cost. Three methodologies were compared and validated that employ ion exchange (TI + EC), extraction chromatography (EC) and extraction with polymers (ECP). The waste chosen was the activated charcoal from the purification system of primary circuit water cooling the reactor IEA-R1. The charcoal samples were dissolved by acid digestion followed by purification and separation of isotopes with ion exchange resins, extraction and chromatographic extraction polymers. Isotopes were analyzed on an alpha spectrometer, equipped with surface barrier detectors. The chemical yields were satisfactory for the methods TI + EC and EC. ECP method was comparable with those methods only for uranium. Statistical analysis as well the analysis of time spent, amount of secondary waste generated and cost revealed that EC method is the most effective for identifying and quantifying U, Np, Pu, Am and Cm present in charcoal. (author)

  2. Recycling schemes of Americium targets in PWR/MOX cores

    International Nuclear Information System (INIS)

    Maldague, Th.; Pilate, S.; Renard, A.; Harislur, A.; Mouney, H.; Rome, M.

    1999-01-01

    From the orientation studies performed so far, both ways to recycle Am in PWR/MOX cores, homogeneous in MOX or heterogeneous in target pins, appear feasible, provided that enriched UO 2 is used as support of the MOX fuel. Multiple recycling can then proceed and stabilize Pu and Am quantities. With respect to the Pu multiple recycling strategy, recycling Am in addition needs 1/3 more 235 U, and creates 3 times more Curium. Thus, although feasible, such a fuel cycle is complicated and brings about a significant cost penalty, not quantified yet. The advantage of the heterogeneous option is to allow to manage in different ways the Pu in MOX fuel and the Am in target pins. For example, should Am remain combined to Cm after reprocessing, the recycling of a mix of Am+Cm could be deferred to let Cm transform into Pu before irradiation. The Am+Cm targets could also stay longer in the reactor, so as to avoid further reprocessing if possible. (author)

  3. Help at 3:00 AM! Providing 24/7 Timely Support to Online Students via a Virtual Assistant

    Science.gov (United States)

    Vu, Phu; Fredrickson, Scott; Meyer, Richard

    2016-01-01

    With a dearth of research on human-robot interaction in education and relatively high non-completion rates of online students, this study was conducted to determine the feasibility of using a virtual assistant (VA) to respond to questions and concerns of students and provide 24/7 online course content support. During a 16 week-long academic…

  4. 40 CFR 174.524 - Glyphosate Oxidoreductase GOX or GOXv247 in all plants; exemption from the requirement of a...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Glyphosate Oxidoreductase GOX or... REQUIREMENTS FOR PLANT-INCORPORATED PROTECTANTS Tolerances and Tolerance Exemptions § 174.524 Glyphosate... Glyphosate Oxidoreductase GOX or GOXv247 enzyme in all plants are exempt from the requirement of a tolerance...

  5. 32 CFR Appendix C to Part 247 - Mailing of DoD Newspapers, Magazines, CE Guides, and Installation Maps; Sales and Distribution of...

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 2 2010-07-01 2010-07-01 false Mailing of DoD Newspapers, Magazines, CE Guides...) MISCELLANEOUS DEPARTMENT OF DEFENSE NEWSPAPERS, MAGAZINES AND CIVILIAN ENTERPRISE PUBLICATIONS Pt. 247, App. C Appendix C to Part 247—Mailing of DoD Newspapers, Magazines, CE Guides, and Installation Maps; Sales and...

  6. PHL 6625: A Minor Merger-associated QSO Behind NGC 247

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Lian; Feng, Hua [Department of Engineering Physics, Tsinghua University, Beijing 100084 (China); Shen, Yue; Liu, Xin [Department of Astronomy, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Ho, Luis C. [Kavli Institute for Astronomy and Astrophysics, Peking University, Beijing 100087 (China); Ge, Junqiang [National Astronomical Observatories, Chinese Academy of Sciences, 20A Datun Road, Chaoyang District, Beijing 100012 (China); Kaaret, Philip [Department of Physics and Astronomy, University of Iowa, Iowa City, IA 52242 (United States); Mao, Shude [Center for Astrophysics, Tsinghua University, Beijing 100084 (China)

    2017-06-01

    PHL 6625 is a luminous quasi-stellar object (QSO) at z = 0.3954 located behind the nearby galaxy NGC 247 ( z = 0.0005). Hubble Space Telescope observations revealed an arc structure associated with it. We report on spectroscopic observations with the Very Large Telescope and multiwavelength observations from the radio to the X-ray band for the system, suggesting that PHL 6625 and the arc are a close pair of merging galaxies, instead of a strong gravitational lens system. The QSO host galaxy is estimated to be (4–28) × 10{sup 10} M {sub ☉} and the mass of the companion galaxy is estimated to be M {sub *} = (6.8 ± 2.4) × 10{sup 9} M {sub ☉}, suggesting that this is a minor merger system. The QSO displays typical broad emission lines, from which a black hole mass of about (2–5) × 10{sup 8} M {sub ☉} and an Eddington ratio of about 0.01–0.05 can be inferred. The system represents an interesting and rare case where a QSO is associated with an ongoing minor merger, analogous to Arp 142.

  7. THE DEVELOPMENT OF BIOCHEMICAL OXYGEN DEMAND SENSOR USING LOCAL YEAST: Candida fukuyamaensis, UICC Y-247

    Directory of Open Access Journals (Sweden)

    Endang Saepudin

    2011-04-01

    Full Text Available In order to shorten the measurement time of biochemical oxygen demand (BOD, a BOD sensor based on yeastmetabolism was developed. Local yeast, Indonesian Origin, Candida fukuyamaensis UICC Y-247, was used as atransducer. The yeast was immobilized as a thin film in agarose matrix with the auxiliary of Nafion® acting as themembrane for ion exchange process. The film was then attached to gold-modified glassy carbons and used as transduceron the working electrodes. The measurements were conducted by observing the depletion of glucose concentrationusing multipulse amperometric method and then converted to BOD values. Optimum condition was observed in awaiting measurement time of 30 min at an applied potential of 450 mV (vs. Ag/AgCl. Linearity was shown in glucoseconcentration range of 0.1–0.5 mM, which was equivalent to BOD concentration range of 10–50 mg/L. A detectionlimit of 1.13 mg/L BOD could be achieved. Good repeatability was shown by a relative standard deviation (RSD of2.7% (n = 15. However, decreasing current response of ~50% was found after 3 days. Comparing to the conventionalBOD measurement, this BOD sensor can be used as an alternative method for BOD measurements.

  8. LCF- and LCF/HCF-behaviour of the superalloy MAR-M247LC

    Energy Technology Data Exchange (ETDEWEB)

    Gelmedin, Domnin; Lang, Karl-Heinz [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany). Inst. fuer Werkstoffkunde I

    2010-07-01

    The fatigue behaviour of the Nickel-base superalloy Mar-M247LC was investigated at 650 C in air environment under total strain control. Pure low cycle fatigue (LCF) loading, pure high cycle fatigue (HCF) loading and superimposed LCF/HCF loading were realised. In LCF tests with a strain ratio of zero and a hold time of 60 seconds the cyclic deformation and the lifetime behaviour was investigated. The dependence of the fatigue limit on the mean strain was estimated in HCF tests at a frequency of 60 Hz using an ultimate number of cycles of ten million. Finally the influence of superimposed HCF and LCF loadings was examined. At high total strain ranges of the HCF loading the lifetime of the superalloy as reduced about more than one magnitude compared to the lifetime under pure LCF loading. With decreasing HCF loadings the reduction of the lifetime decreases. This life time reduction can be explained by the interaction of the LCF and the superimposed HCF loading. Crack initiation and first crack propagation is predominantly induced by the LCF loading. After reaching an adequate long fatigue crack length the superimposed HCF loading contributes considerably to the crack growth. This contribution can be determined evaluating the distance between the LCF marking lines which form on the fracture surface. The higher the superimposed HCF loading was the longer the distance between the LCF marking lines and the lower the crack length were when first LCF marking lines could be recognized. On the basis of this cognition the life time under superimposed LCF/HCF loading was modelled using a model basing on fracture mechanics. (orig.)

  9. Missed surgical intensive care unit billing: potential financial impact of 24/7 faculty presence.

    Science.gov (United States)

    Hendershot, Kimberly M; Bollins, John P; Armen, Scott B; Thomas, Yalaunda M; Steinberg, Steven M; Cook, Charles H

    2009-07-01

    To efficiently capture evaluation and management (E&M) and procedural billing in our surgical intensive care unit (SICU), we have developed an electronic billing system that links to the electronic medical record (EMR). In this system, only notes electronically signed and coded by an attending generate billing charges. We hypothesized that capture of missed billing during nighttime and weekends might be sufficient to subsidize 24/7 in-house attending coverage. A retrospective chart EMR review was performed of the EMRs for all SICU patients during a 2-month period. Note type, date, time, attending signature, and coding were analyzed. Notes without attending signature, diagnosis, or current procedural terminology (CPT) code were considered incomplete and identified as "missed billing." Four hundred and forty-three patients had 465 admissions generating 2,896 notes. Overall, 76% of notes were signed and coded by an attending and billed. Incomplete (not billed) notes represented an overall missed billing opportunity of $159,138 for the 2-month time period (approximately $954,000 annually). Unbilled E&M encounters during weekdays totaled $54,758, whereas unbilled E&M and procedures from weeknights and weekends totaled $88,408 ($44,566 and $43,842, respectively). Missed billing after-hours thus represents approximately $530K annually, extrapolating to approximately $220K in collections from our payer mix. Surprisingly, missed E&M and procedural billing during weekdays totaled $70,730 (approximately $425K billing, approximately $170K collections annually), and typically represented patients seen, but transferred from the SICU before attending documentation was completed. Capture of nighttime and weekend ICU collections alone may be insufficient to add faculty or incentivize in-house coverage, but could certainly complement other in-house derived revenues to such ends. In addition, missed daytime billing in busy modern ICUs can be substantial, and use of an EMR to identify

  10. MOLECULAR CLUMPS AND INFRARED CLUSTERS IN THE S247, S252, AND BFS52 REGIONS

    Energy Technology Data Exchange (ETDEWEB)

    Shimoikura, Tomomi; Dobashi, Kazuhito [Department of Astronomy and Earth Sciences, Tokyo Gakugei University, Koganei, Tokyo 184-8501 (Japan); Saito, Hiro; Nakamura, Fumitaka [National Astronomical Observatory of Japan, Mitaka, Tokyo 181-8588 (Japan); Matsumoto, Tomoaki [Hosei University, Fujimi, Chiyoda-ku, Tokyo 102-8160 (Japan); Nishimura, Atsushi; Kimura, Kimihiro; Onishi, Toshikazu; Ogawa, Hideo, E-mail: ikura@u-gakugei.ac.jp [Department of Physical Science, Osaka Prefecture University, Sakai, Osaka 599-8531 (Japan)

    2013-05-01

    We present results of the observations carried out toward the S247, S252, and BFS52 H II regions with various molecular lines using the 1.85 m radio telescope and the 45 m telescope at Nobeyama Radio Observatory. There are at least 11 young infrared clusters (IR clusters) within the observed region. We found that there are two velocity components in {sup 12}CO (J = 2-1), and also that their spatial distributions show an anti-correlation. The IR clusters are located at their interfaces, suggesting that two distinct clouds with different velocities are colliding with each other, which may have induced the cluster formation. Based on {sup 13}CO (J = 1-0) and C{sup 18}O (J = 1-0) observations, we identified 16 clumps in and around the three H II regions. Eleven of the clumps are associated with the IR clusters and the other five clumps are not associated with any known young stellar objects. We investigated variations in the velocity dispersions of the 16 clumps as a function of the distance from the center of the clusters or the clumps. Clumps with clusters tend to have velocity dispersions that increase with distance from the cluster center, while clumps without clusters show a flat velocity dispersion over the clump extents. A {sup 12}CO outflow has been found in some of the clumps with IR clusters but not in the other clumps, supporting a strong relation of these clumps to the broader velocity dispersion region. We also estimated a mean star formation efficiency of {approx}30% for the clumps with IR clusters in the three H II regions.

  11. Prediction of maximum casting defect size in MAR-M-247 alloy processed by hot isostatic pressing

    Czech Academy of Sciences Publication Activity Database

    Šmíd, Miroslav; Fintová, Stanislava; Kunz, Ludvík; Hutař, Pavel; Hrbáček, K.

    2015-01-01

    Roč. 22, č. 1 (2015), s. 25-32 ISSN 1335-0803 R&D Projects: GA MPO FR-TI4/030; GA MŠk(CZ) EE2.3.20.0214 Institutional support: RVO:68081723 Keywords : MAR-M 247 * Superalloys * Fatigue * Casting defects * Elevated temperatures Subject RIV: JL - Materials Fatigue, Friction Mechanics http://ojs.mateng.sk/index.php/Mateng/article/view/160/249

  12. Selective Cathepsin S Inhibition with MIV-247 Attenuates Mechanical Allodynia and Enhances the Antiallodynic Effects of Gabapentin and Pregabalin in a Mouse Model of Neuropathic Pain.

    Science.gov (United States)

    Hewitt, Ellen; Pitcher, Thomas; Rizoska, Biljana; Tunblad, Karin; Henderson, Ian; Sahlberg, Britt-Louise; Grabowska, Urszula; Classon, Björn; Edenius, Charlotte; Malcangio, Marzia; Lindström, Erik

    2016-09-01

    Cathepsin S inhibitors attenuate mechanical allodynia in preclinical neuropathic pain models. The current study evaluated the effects when combining the selective cathepsin S inhibitor MIV-247 with gabapentin or pregabalin in a mouse model of neuropathic pain. Mice were rendered neuropathic by partial sciatic nerve ligation. MIV-247, gabapentin, or pregabalin were administered alone or in combination via oral gavage. Mechanical allodynia was assessed using von Frey hairs. Neurobehavioral side effects were evaluated by assessing beam walking. MIV-247, gabapentin, and pregabalin concentrations in various tissues were measured. Oral administration of MIV-247 (100-200 µmol/kg) dose-dependently attenuated mechanical allodynia by up to approximately 50% reversal when given as a single dose or when given twice daily for 5 days. No behavioral deficits were observed at any dose of MIV-247 tested. Gabapentin (58-350 µmol/kg) and pregabalin (63-377 µmol/kg) also inhibited mechanical allodynia with virtually complete reversal at the highest doses tested. The minimum effective dose of MIV-247 (100 µmol/kg) in combination with the minimum effective dose of pregabalin (75 µmol/kg) or gabapentin (146 µmol/kg) resulted in enhanced antiallodynic efficacy without augmenting side effects. A subeffective dose of MIV-247 (50 µmol/kg) in combination with a subeffective dose of pregabalin (38 µmol/kg) or gabapentin (73 µmol/kg) also resulted in substantial efficacy. Plasma levels of MIV-247, gabapentin, and pregabalin were similar when given in combination as to when given alone. Cathepsin S inhibition with MIV-247 exerts significant antiallodynic efficacy alone, and also enhances the effect of gabapentin and pregabalin without increasing side effects or inducing pharmacokinetic interactions. Copyright © 2016 by The American Society for Pharmacology and Experimental Therapeutics.

  13. The energy and monetary implications of the '24/7 'always on' society

    Energy Technology Data Exchange (ETDEWEB)

    Loveday, Dennis L. [Department of Civil and Building Engineering, Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom); Bhamra, T.; Tang, T. [Department of Design and Technology, Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom); Haines, V.J.A. [Ergonomics and Safety Research Institute (ESRI), Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom); Holmes, M.J. [ARUP, 13, Fitzroy Street, London W1T 4BR (United Kingdom); Green, R.J. [Institute for Energy Research and Policy, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

    2008-12-15

    This paper reviews the trends in society, technology and energy demand of the past 30 years, together with the growth of the 'on-demand' culture. The '24/7' or 'always on' society can be defined as one where people demand - and generally receive - what they want 'now'. It has grown up in parallel with developments in information technology, which have produced the services needed to meet that demand. Larger numbers of appliances, resulting from greater affluence and disposable income, have increased energy use, despite energy efficiencies in other areas. While monetary factors suggest that changes brought about by the 24/7 society will generally be self-correcting at the macro-economic level, there will nevertheless be effects for individuals, such as potentially severe impacts on the fuel poor as electricity prices rise. We conclude with a view of future directions. As the 24/7 culture continues to grow, there is scope for designers and for information technology to manage and reduce energy consumption. This includes buildings, their services systems, and the mix of new technologies that will be deployed over the next 20 years or so, including the possibilities for data exchange and control at the interface between energy suppliers and consumers, coupled with greater understanding of the behaviour of the consumers themselves. (author)

  14. The energy and monetary implications of the '24/7' 'always on' society

    Energy Technology Data Exchange (ETDEWEB)

    Loveday, Dennis L. [Department of Civil and Building Engineering, Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom)], E-mail: d.l.loveday@lboro.ac.uk; Bhamra, T.; Tang, T. [Department of Design and Technology, Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom); Haines, V.J.A. [Ergonomics and Safety Research Institute (ESRI), Loughborough University, Loughborough, Leicestershire LE11 3TU (United Kingdom); Holmes, M.J. [ARUP, 13, Fitzroy Street, London W1T 4BR (United Kingdom); Green, R.J. [Institute for Energy Research and Policy, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom)

    2008-12-15

    This paper reviews the trends in society, technology and energy demand of the past 30 years, together with the growth of the 'on-demand' culture. The '24/7' or 'always on' society can be defined as one where people demand-and generally receive-what they want 'now'. It has grown up in parallel with developments in information technology, which have produced the services needed to meet that demand. Larger numbers of appliances, resulting from greater affluence and disposable income, have increased energy use, despite energy efficiencies in other areas. While monetary factors suggest that changes brought about by the 24/7 society will generally be self-correcting at the macro-economic level, there will nevertheless be effects for individuals, such as potentially severe impacts on the fuel poor as electricity prices rise. We conclude with a view of future directions. As the 24/7 culture continues to grow, there is scope for designers and for information technology to manage and reduce energy consumption. This includes buildings, their services systems, and the mix of new technologies that will be deployed over the next 20 years or so, including the possibilities for data exchange and control at the interface between energy suppliers and consumers, coupled with greater understanding of the behaviour of the consumers themselves.

  15. Preliminary Mark-18A (Mk-18A) Target Material Recovery Program Product Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, Sharon M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Patton, Bradley D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-09-01

    The Mk-18A Target Material Recovery Program (MTMRP) was established in 2015 to preserve the unique materials, e.g. 244Pu, in 65 previously irradiated Mk-18A targets for future use. This program utilizes existing capabilities at SRS and Savannah River National Laboratory (SRNL) to process targets, recover materials from them, and to package the recovered materials for shipping to ORNL. It also utilizes existing capabilities at ORNL to receive and store the recovered materials, and to provide any additional processing of the recovered materials or residuals required to prepare them for future beneficial use. The MTMRP is presently preparing for the processing of these valuable targets which is expected to begin in ~2019. As part of the preparations for operations, this report documents the preliminary acceptance criteria for the plutonium and heavy curium materials to be recovered from the Mk-18A targets at SRNL for transport and storage at ORNL. These acceptance criteria were developed based on preliminary concepts developed for processing, transporting, and storing the recovered Mk-18A materials. They will need to be refined as these concepts are developed in more detail.

  16. Preliminary Mark-18A (Mk-18A) Target Material Recovery Program Product Acceptance Criteria

    International Nuclear Information System (INIS)

    Robinson, Sharon M.; Patton, Bradley D.

    2016-01-01

    The Mk-18A Target Material Recovery Program (MTMRP) was established in 2015 to preserve the unique materials, e.g. 244 Pu, in 65 previously irradiated Mk-18A targets for future use. This program utilizes existing capabilities at SRS and Savannah River National Laboratory (SRNL) to process targets, recover materials from them, and to package the recovered materials for shipping to ORNL. It also utilizes existing capabilities at ORNL to receive and store the recovered materials, and to provide any additional processing of the recovered materials or residuals required to prepare them for future beneficial use. The MTMRP is presently preparing for the processing of these valuable targets which is expected to begin in ~2019. As part of the preparations for operations, this report documents the preliminary acceptance criteria for the plutonium and heavy curium materials to be recovered from the Mk-18A targets at SRNL for transport and storage at ORNL. These acceptance criteria were developed based on preliminary concepts developed for processing, transporting, and storing the recovered Mk-18A materials. They will need to be refined as these concepts are developed in more detail.

  17. Target fuels for plutonium and minor actinide transmutation in pressurized water reactors

    International Nuclear Information System (INIS)

    Washington, J.; King, J.; Shayer, Z.

    2017-01-01

    Highlights: • We evaluate transmutation fuels for plutonium and minor actinide destruction in LWRs. • We model a modified AP1000 fuel assembly in SCALE6.1. • We evaluate spectral shift absorber coatings to improve transmutation performance. - Abstract: The average nuclear power plant produces twenty metric tons of used nuclear fuel per year, containing approximately 95 wt% uranium, 1 wt% plutonium, and 4 wt% fission products and transuranic elements. Fast reactors are a preferred option for the transmutation of plutonium and minor actinides; however, an optimistic deployment time of at least 20 years indicates a need for a nearer-term solution. This study considers a method for plutonium and minor actinide transmutation in existing light water reactors and evaluates a variety of transmutation fuels to provide a common basis for comparison and to determine if any single target fuel provides superior transmutation properties. A model developed using the NEWT module in the SCALE 6.1 code package provided performance data for the burnup of the target fuel rods in the present study. The target fuels (MOX, PuO_2, Pu_3Si_2, PuN, PuUZrH, PuZrH, PuZrHTh, and PuZrO_2) are evaluated over a 1400 Effective Full Power Days (EFPD) interval to ensure each assembly remained critical over the entire burnup period. The MOX (5 wt% PuO_2), Pu_0_._3_1ZrH_1_._6Th_1_._0_8, and PuZrO_2MgO (8 wt% Pu) fuels result in the highest rate of plutonium transmutation with the lowest rate of curium-244 production. This study selected eleven different burnable absorbers (B_4C, CdO, Dy_2O_3, Er_2O_3, Eu_2O_3, Gd_2O_3, HfO_2, In_2O_3, Lu_2O_3, Sm_2O_3, and TaC) for evaluation as spectral shift absorber coatings on the outside of the fuel pellets to determine if an absorber coating can improve the transmutation properties of the target fuels. The PuZrO_2MgO (8 wt% Pu) target fuel with a coating of Lu_2O_3 resulted in the highest rate of plutonium transmutation with the greatest reduction in curium

  18. Target fuels for plutonium and minor actinide transmutation in pressurized water reactors

    Energy Technology Data Exchange (ETDEWEB)

    Washington, J., E-mail: jwashing@gmail.com [Nuclear Science and Engineering Program, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); King, J., E-mail: kingjc@mines.edu [Nuclear Science and Engineering Program, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States); Shayer, Z., E-mail: zshayer@mines.edu [Department of Physics, Colorado School of Mines, 1500 Illinois St., Golden, CO 80401 (United States)

    2017-03-15

    Highlights: • We evaluate transmutation fuels for plutonium and minor actinide destruction in LWRs. • We model a modified AP1000 fuel assembly in SCALE6.1. • We evaluate spectral shift absorber coatings to improve transmutation performance. - Abstract: The average nuclear power plant produces twenty metric tons of used nuclear fuel per year, containing approximately 95 wt% uranium, 1 wt% plutonium, and 4 wt% fission products and transuranic elements. Fast reactors are a preferred option for the transmutation of plutonium and minor actinides; however, an optimistic deployment time of at least 20 years indicates a need for a nearer-term solution. This study considers a method for plutonium and minor actinide transmutation in existing light water reactors and evaluates a variety of transmutation fuels to provide a common basis for comparison and to determine if any single target fuel provides superior transmutation properties. A model developed using the NEWT module in the SCALE 6.1 code package provided performance data for the burnup of the target fuel rods in the present study. The target fuels (MOX, PuO{sub 2}, Pu{sub 3}Si{sub 2}, PuN, PuUZrH, PuZrH, PuZrHTh, and PuZrO{sub 2}) are evaluated over a 1400 Effective Full Power Days (EFPD) interval to ensure each assembly remained critical over the entire burnup period. The MOX (5 wt% PuO{sub 2}), Pu{sub 0.31}ZrH{sub 1.6}Th{sub 1.08}, and PuZrO{sub 2}MgO (8 wt% Pu) fuels result in the highest rate of plutonium transmutation with the lowest rate of curium-244 production. This study selected eleven different burnable absorbers (B{sub 4}C, CdO, Dy{sub 2}O{sub 3}, Er{sub 2}O{sub 3}, Eu{sub 2}O{sub 3}, Gd{sub 2}O{sub 3}, HfO{sub 2}, In{sub 2}O{sub 3}, Lu{sub 2}O{sub 3}, Sm{sub 2}O{sub 3}, and TaC) for evaluation as spectral shift absorber coatings on the outside of the fuel pellets to determine if an absorber coating can improve the transmutation properties of the target fuels. The PuZrO{sub 2}MgO (8 wt% Pu) target

  19. 17 CFR 247.781 - Exemption from the definition of “broker” for banks for a limited period of time.

    Science.gov (United States)

    2010-04-01

    ... “broker” for banks for a limited period of time. A bank is exempt from the definition of the term “broker... 17 Commodity and Securities Exchanges 3 2010-04-01 2010-04-01 false Exemption from the definition of âbrokerâ for banks for a limited period of time. 247.781 Section 247.781 Commodity and Securities...

  20. Performance of the multiple target He/PbI sub 2 aerosol jet system for mass separation of neutron-deficient actinide isotopes

    CERN Document Server

    Ichikawa, S; Asai, M; Haba, H; Sakama, M; Kojima, Y; Shibata, M; Nagame, Y; Oura, Y; Kawade, K

    2002-01-01

    A multiple target He/PbI sub 2 aerosol jet system coupled with a thermal ion source was installed in the isotope separator on line (JAERI-ISOL) at the JAERI tandem accelerator facility. The neutron-deficient americium and curium isotopes produced in the sup 2 sup 3 sup 3 sup , sup 2 sup 3 sup 5 U( sup 6 Li, xn) and sup 2 sup 3 sup 7 Np( sup 6 Li, xn) reactions were successfully mass-separated and the overall efficiency including the ionization of Am atoms was evaluated to be 0.3-0.4%. The identification of a new isotope sup 2 sup 3 sup 7 Cm with the present system is reported.

  1. CERN: Fixed target targets

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1993-03-15

    Full text: While the immediate priority of CERN's research programme is to exploit to the full the world's largest accelerator, the LEP electron-positron collider and its concomitant LEP200 energy upgrade (January, page 1), CERN is also mindful of its long tradition of diversified research. Away from LEP and preparations for the LHC proton-proton collider to be built above LEP in the same 27-kilometre tunnel, CERN is also preparing for a new generation of heavy ion experiments using a new source, providing heavier ions (April 1992, page 8), with first physics expected next year. CERN's smallest accelerator, the LEAR Low Energy Antiproton Ring continues to cover a wide range of research topics, and saw a record number of hours of operation in 1992. The new ISOLDE on-line isotope separator was inaugurated last year (July, page 5) and physics is already underway. The remaining effort concentrates around fixed target experiments at the SPS synchrotron, which formed the main thrust of CERN's research during the late 1970s. With the SPS and LEAR now approaching middle age, their research future was extensively studied last year. Broadly, a vigorous SPS programme looks assured until at least the end of 1995. Decisions for the longer term future of the West Experimental Area of the SPS will have to take into account the heavy demand for test beams from work towards experiments at big colliders, both at CERN and elsewhere. The North Experimental Area is the scene of larger experiments with longer lead times. Several more years of LEAR exploitation are already in the pipeline, but for the longer term, the ambitious Superlear project for a superconducting ring (January 1992, page 7) did not catch on. Neutrino physics has a long tradition at CERN, and this continues with the preparations for two major projects, the Chorus and Nomad experiments (November 1991, page 7), to start next year in the West Area. Delicate neutrino oscillation effects could become visible for the first

  2. CERN: Fixed target targets

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    Full text: While the immediate priority of CERN's research programme is to exploit to the full the world's largest accelerator, the LEP electron-positron collider and its concomitant LEP200 energy upgrade (January, page 1), CERN is also mindful of its long tradition of diversified research. Away from LEP and preparations for the LHC proton-proton collider to be built above LEP in the same 27-kilometre tunnel, CERN is also preparing for a new generation of heavy ion experiments using a new source, providing heavier ions (April 1992, page 8), with first physics expected next year. CERN's smallest accelerator, the LEAR Low Energy Antiproton Ring continues to cover a wide range of research topics, and saw a record number of hours of operation in 1992. The new ISOLDE on-line isotope separator was inaugurated last year (July, page 5) and physics is already underway. The remaining effort concentrates around fixed target experiments at the SPS synchrotron, which formed the main thrust of CERN's research during the late 1970s. With the SPS and LEAR now approaching middle age, their research future was extensively studied last year. Broadly, a vigorous SPS programme looks assured until at least the end of 1995. Decisions for the longer term future of the West Experimental Area of the SPS will have to take into account the heavy demand for test beams from work towards experiments at big colliders, both at CERN and elsewhere. The North Experimental Area is the scene of larger experiments with longer lead times. Several more years of LEAR exploitation are already in the pipeline, but for the longer term, the ambitious Superlear project for a superconducting ring (January 1992, page 7) did not catch on. Neutrino physics has a long tradition at CERN, and this continues with the preparations for two major projects, the Chorus and Nomad experiments (November 1991, page 7), to start next year in the West Area. Delicate neutrino oscillation effects could become

  3. Am/Cm target glass durability dependence on pH (U). Revision 1

    International Nuclear Information System (INIS)

    Daniel, W.E.; Best, D.R.

    1996-03-01

    At the Westinghouse Savannah River Company near Aiken, South Carolina, a process is being developed to safely vitrify all of the highly radioactive americium/curium (Am/Cm) material and a portion of the other fissile actinide materials stored on site. One goal of this campaign is to provide Oak Ridge National Laboratory with the excess Am/Cm so it can be recycled as opposed to simply disposing of it as waste. The vitrification will allow safe transportation of the Am/Cm to Oak Ridge as well as safe storage once it arrives. The Am/Cm Target glass being used in this project has been specifically designed to be extremely durable in aqueous environments while it can be selectively attacked by nitric acid to recover the valuable Am and Cm isotopes. Similar glass compositions could be used for storage and retrieval of other actinides on the WSRC site. Previous reports have presented the time, temperature, and compositional dependence of the Am/Cm glass durability. This paper will show results from a pH study on the Am/Cm Target glass durability. The data indicate that the Am/Cm Target Glass durability decreases as pH decreases from a neutral reading. These findings support the extraction of the valuable isotopes from the glass using nitric acid

  4. Target laboratory

    International Nuclear Information System (INIS)

    Ephraim, D.C.; Pednekar, A.R.

    1993-01-01

    A target laboratory to make stripper foils for the accelerator and various targets for use in the experiments is set up in the pelletron accelerator facility. The facilities available in the laboratory are: (1) D.C. glow discharge setup, (2) carbon arc set up, and (3) vacuum evaporation set up (resistance heating), electron beam source, rolling mill - all for target preparation. They are described. Centrifugal deposition technique is used for target preparation. (author). 3 figs

  5. Ice targets

    International Nuclear Information System (INIS)

    Pacheco, C.; Stark, C.; Tanaka, N.; Hodgkins, D.; Barnhart, J.; Kosty, J.

    1979-12-01

    This report presents a description of ice targets that were constructed for research work at the High Resolution Spectrometer (HRS) and at the Energetic Pion Channel and Spectrometer (EPICS). Reasons for using these ice targets and the instructions for their construction are given. Results of research using ice targets will be published at a later date

  6. Effect of Process Variables on the Inertia Friction Welding of Superalloys LSHR and Mar-M247

    Science.gov (United States)

    Mahaffey, D. W.; Senkov, O. N.; Shivpuri, R.; Semiatin, S. L.

    2016-08-01

    The effect of inertia friction welding process parameters on microstructure evolution, weld plane quality, and the tensile behavior of welds between dissimilar nickel-base superalloys was established. For this purpose, the fine-grain, powder metallurgy alloy LSHR was joined to coarse-grain cast Mar-M247 using a fixed level of initial kinetic energy, but different combinations of the flywheel moment of inertia and initial rotation speed. It was found that welds made with the largest moment of inertia resulted in a sound bond with the best microstructure and room-temperature tensile strength equal to or greater than that of the parent materials. A relationship between the moment of inertia and weld process efficiency was established. The post-weld tensile behavior was interpreted in the context of observed microstructure gradients and weld-line defects.

  7. Synthesis of the enantiomers of [3-{sup 3}H]-2-[[4-[(7-chloro-4-quinolinyl)-amino]pentyl]ethylamino]eth anol, [3-{sup 3}H]-hydroxychloroquine

    Energy Technology Data Exchange (ETDEWEB)

    Ellames, G.J.; Herbert, J.M.; Peace, J.E.; Smith, D.J.; Wedge, K.J. [Sterling Winthrop Research Centre, Alnwick (United Kingdom). Pharmaceuticals Research Div.

    1995-01-01

    The enantiomers of [3-{sup 3}H]-2-[[4-[(7-chloro-4-quinolinyl)amino] pentyl]ethylamino]ethanol, [3-{sup 3}H]-hydroxychloroquine, (R)-8 and (S)-8, have been prepared in two steps from the known precursors 4,7-dichloro-3-iodoquinoline, and the enantiomers of 2-[(4-aminopentyl) ethyl-amino]ethanol, (R)-2 and (S)-2, by formation of the enantiomers of 2-[[4-[(7-chloro-3-iodo-4-quinolinyl)amino]pentyl]ethylamino] ethanol, (R)-3 and (S)-3, and subsequent reductive deiodination with tritium gas over 10% palladium on charcoal. (Author).

  8. Synthesis of the enantiomers of [3-3H]-2-[[4-[(7-chloro-4-quinolinyl)-amino]pentyl]ethylamino]eth anol, [3-3H]-hydroxychloroquine

    International Nuclear Information System (INIS)

    Ellames, G.J.; Herbert, J.M.; Peace, J.E.; Smith, D.J.; Wedge, K.J.

    1995-01-01

    The enantiomers of [3- 3 H]-2-[[4-[(7-chloro-4-quinolinyl)amino] pentyl]ethylamino]ethanol, [3- 3 H]-hydroxychloroquine, (R)-8 and (S)-8, have been prepared in two steps from the known precursors 4,7-dichloro-3-iodoquinoline, and the enantiomers of 2-[(4-aminopentyl) ethyl-amino]ethanol, (R)-2 and (S)-2, by formation of the enantiomers of 2-[[4-[(7-chloro-3-iodo-4-quinolinyl)amino]pentyl]ethylamino] ethanol, (R)-3 and (S)-3, and subsequent reductive deiodination with tritium gas over 10% palladium on charcoal. (Author)

  9. High cycle fatigue behavior of the IN718/M247 hybrid element fabricated by friction welding at elevated temperatures

    Directory of Open Access Journals (Sweden)

    Tran Hung Tra

    2016-12-01

    Full Text Available A hybrid element has been fabricated by friction welding, joining two superalloys Inconel 718 and Mar-M247. The high cycle fatigue behavior of this welded element was investigated at 500 °C and 700 °C. The fabrication could obtain excellent fatigue strength in which the fracture is located in the base metal Mar-M247 side and takes place outside the welded zone. The behavior of the joint under loadings is discussed through a simulation by the numerical finite element method.

  10. Nuclear engineering 24/7 via distance learning: Course development and management experiences

    International Nuclear Information System (INIS)

    Maldonado, G. I.; Christenson, J.; Spitz, H.; Rutz, E.; Todd, A.

    2006-01-01

    This article summarizes a few lessons learned in our early experiences in developing, delivering and implementing a series of distance learning classes for full-time undergraduate students enrolled in the combined-degree BS Mechanical + MS Nuclear Engineering 5-year and co-op based 'MNE- ACCEND' program at the Univ. of Cincinnati. This program is in its third year since inception and currently hosts approximately 35 undergraduate students enrolled in the graduating classes of 2008, 2009, and 2010, which is when these students are expected to complete their BS Mechanical and MS Nuclear Engineering degrees. In addition, 20+ newly confirmed students are expected to enter this program in the fall quarter of 2006 to become our Class of 2011. Therefore, the successful 'follow through' of the DL component of this program continues to be increasingly crucial as this student pipeline reaches a targeted steady-state of about 10 to 15 graduates per class. (authors)

  11. Isotope materials availability and services for target production at the Oak Ridge National Laboratory

    International Nuclear Information System (INIS)

    Ratledge, J.E.; Dahl, T.L.; Ottinger, C.L.; Aaron, W.S.; Adair, H.L.

    1987-01-01

    Materials available through the Isotope Distribution Program include separated stable isotopes, byproduct radioisotopes, and research quantities of source and special nuclear materials. Isotope products are routinely available in the forms listed in the product description section of the Isotopes Products and Services Catalog distributed by the Oak Ridge National Laboratory (ORNL). Different forms can be provided in some cases, usually at additional cost. Routinely available services include cyclotron target irradiations, fabrication of special physical forms, source encapsulation, ion implantation, and special purifications. Materials and services that are not offered as part of the routine distribution program may be made available from commercial sources in the United States. Specific forms of isotopic research materials include thin films and foils for use as accelerator targets, metal or other compounds in the form of bars or wires, and metal foils. Methods of fabrication include evaporation, sputtering, rolling, electrolytic deposition, pressing, sintering, and casting. High-purity metal forms of plutonium, americium, and curium are prepared by vacuum reduction/distillation. Both fissionable and nonfissionable neutron dosimeters are prepared for determining the neutron energy spectra, flux, and fluence at various locations within a reactor. Details on what materials are available and how the materials and related services can be obtained from ORNL are described. (orig.)

  12. Development and Pilot Testing of 24/7 In-Ambulance Telemedicine for Acute Stroke : Prehospital Stroke Study at the Universitair Ziekenhuis Brussel-Project

    NARCIS (Netherlands)

    Espinoza, Alexis Valenzuela; Van Hooff, Robbert-Jan; De Smedt, Ann; Moens, Maarten; Yperzeele, Laetitia; Nieboer, Koenraad; Hubloue, Ives; de Keyser, Jacques; Convents, Andre; Tellez, Helio Fernandez; Dupont, Alain; Putman, Koen; Brouns, Raf

    2016-01-01

    Background: In-ambulance telemedicine is a recently developed and a promising approach to improve emergency care. We implemented the first ever 24/7 in-ambulance telemedicine service for acute stroke. We report on our experiences with the development and pilot testing of the Prehospital Stroke Study

  13. A Gene Encoding a DUF247 Domain Protein Cosegregates with the S Self-Incompatibility Locus in Perennial Ryegrass

    DEFF Research Database (Denmark)

    Manzanares, Chloe; Barth, Susanne; Thorogood, Daniel

    2016-01-01

    genes cosegregating with the S-locus, a highly polymorphic gene encoding for a protein containing a DUF247 was fully predictive of known S-locus genotypes at the amino acid level in the seven mapping populations. Strikingly, this gene showed a frameshift mutation in self-compatible darnel (Lolium...

  14. Development and Pilot Testing of 24/7 In-Ambulance Telemedicine for Acute Stroke: Prehospital Stroke Study at the Universitair Ziekenhuis Brussel-Project.

    Science.gov (United States)

    Valenzuela Espinoza, Alexis; Van Hooff, Robbert-Jan; De Smedt, Ann; Moens, Maarten; Yperzeele, Laetitia; Nieboer, Koenraad; Hubloue, Ives; de Keyser, Jacques; Convents, Andre; Fernandez Tellez, Helio; Dupont, Alain; Putman, Koen; Brouns, Raf

    2016-01-01

    In-ambulance telemedicine is a recently developed and a promising approach to improve emergency care. We implemented the first ever 24/7 in-ambulance telemedicine service for acute stroke. We report on our experiences with the development and pilot testing of the Prehospital Stroke Study at the Universitair Ziekenhuis Brussel (PreSSUB) to facilitate a wider spread of the knowledge regarding this technique. Successful execution of the project involved the development and validation of a novel stroke scale, design and creation of specific hardware and software solutions, execution of field tests for mobile internet connectivity, design of new care processes and information flows, recurrent training of all professional caregivers involved in acute stroke management, extensive testing on healthy volunteers, organisation of a 24/7 teleconsultation service by trained stroke experts and 24/7 technical support, and resolution of several legal issues. In all, it took 41 months of research and development to confirm the safety, technical feasibility, reliability, and user acceptance of the PreSSUB approach. Stroke-specific key information can be collected safely and reliably before and during ambulance transportation and can adequately be communicated with the inhospital team awaiting the patient. This paper portrays the key steps required and the lessons learned for successful implementation of a 24/7 expert telemedicine service supporting patients with acute stroke during ambulance transportation to the hospital. © 2016 S. Karger AG, Basel.

  15. Spatially conserved regulatory elements identified within human and mouse Cd247 gene using high-throughput sequencing data from the ENCODE project

    DEFF Research Database (Denmark)

    Pundhir, Sachin; Hannibal, Tine Dahlbæk; Bang-Berthelsen, Claus Heiner

    2014-01-01

    . In this study, we have utilized the wealth of high-throughput sequencing data produced during the Encyclopedia of DNA Elements (ENCODE) project to identify spatially conserved regulatory elements within the Cd247 gene from human and mouse. We show the presence of two transcription factor binding sites...

  16. Antiproton Target

    CERN Multimedia

    1980-01-01

    Antiproton target used for the AA (antiproton accumulator). The first type of antiproton production target used from 1980 to 1982 comprised a rod of copper 3mm diameter and 120mm long embedded in a graphite cylinder that was itself pressed into a finned aluminium container. This assembly was air-cooled and it was used in conjunction with the Van der Meer magnetic horn. In 1983 Fermilab provided us with lithium lenses to replace the horn with a view to increasing the antiproton yield by about 30%. These lenses needed a much shorter target made of heavy metal - iridium was chosen for this purpose. The 50 mm iridium rod was housed in an extension to the original finned target container so that it could be brought very close to the entrance to the lithium lens. Picture 1 shows this target assembly and Picture 2 shows it mounted together with the lithium lens. These target containers had a short lifetime due to a combination of beam heating and radiation damage. This led to the design of the water-cooled target in...

  17. 24/7 in-house intensivist coverage and fellowship education: a cross-sectional survey of academic medical centers in the United States.

    Science.gov (United States)

    Diaz-Guzman, Enrique; Colbert, Colleen Y; Mannino, David M; Davenport, Daniel L; Arroliga, Alejandro C

    2012-04-01

    The objectives of this study were to determine the current staffing models of practice and the frequency of 24/7 coverage in academic medical centers in the United States and to assess the perceptions of critical care trainees and program directors toward these models. A cross-sectional national survey was conducted using an Internet-based survey platform. The survey was distributed to fellows and program directors of 374 critical care training programs in US academic medical centers. We received 518 responses: 138 from program directors (PDs) (37% of 374 programs) and 380 fellow responses. Coverage by a board-certified or board-eligible intensivist physician 24/7 was reported by 33% of PD respondents and was more common among pediatric and surgical critical care programs. Mandatory in-house call for critical care trainees was reported by 48% of the PDs. Mandatory call was also more common among pediatric-critical care programs compared with the rest (P 24/7 coverage would be associated with better patient care in the ICU and improved education for the fellows, although 65% of them believed this model would have a negative impact on trainees' autonomy. Intensivist coverage 24/7 was not commonly used in US academic centers responding to our survey. Significant differences in coverage models among critical care medicine specialties appear to exist. Program director and trainee respondents believed that 24/7 coverage was associated with better outcomes and education but also expressed concerns about the impact of this model on fellows' autonomy.

  18. Accelerator and spallation target technologies for ADS applications

    International Nuclear Information System (INIS)

    2005-01-01

    The efficient and safe management of spent fuel produced during the operation of commercial nuclear power plants is an important issue. Worldwide, more than 250 000 tons of spent fuel from reactors currently operating will require disposal. These numbers account for only high-level radio-active waste generated by present-day power reactors. Nearly all issues related to risks to future generations arising from the long-term disposal of such spent nuclear fuel is attributable to only about 1% of its content. This 1% is made up primarily of plutonium, neptunium, americium and curium (called transuranic elements) and the long-lived isotopes of iodine and technetium. When transuranics are removed from discharged fuel destined for disposal, the toxic nature of the spent fuel drops below that of natural uranium ore (that which was originally mined for the nuclear fuel) within a period of several hundred years. This significantly reduces the burden on geological repositories and the problem of addressing the remaining long-term residues can thus be done in controlled environments having timescales of centuries rather than millennia. To address the disposal of transuranics, accelerator-driven systems (ADS), i.e. a sub-critical system driven by an accelerator to sustain the chain reaction, seem to have great potential for transuranic transmutation, though much R and D work is still required in order to demonstrate their desired capability as a whole system. This report describes the current status of accelerator and spallation target technologies and suggests technical issues that need to be resolved for ADS applications. It will be of particular interest to nuclear scientists involved in ADS development and in advanced fuel cycles in general. (author)

  19. Expression of the benign HEXA mutations, Arg247Trp and Arg249Trp, associated with beta-hexosaminidase A pseudodeficiency

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Z.; Petroulakis, E.; Salo, T. [Univ. of Manitoba (Canada)] [and others

    1994-09-01

    {beta}-Hexosaminidase (Hex A) is a heterodimer of {alpha} and {beta} subunits encoded by the HEXA and HEXB genes, respectively. Mutations in the HEXA gene typically cause Tay-Sachs disease or less severe forms of G{sub M2} gangliosidosis. However, two benign mutations (Arg247Trp and Arg249Trp) in the {alpha}-subunit of Hex A account for Hex A deficiency in {approximately}36% of non-Jewish enzyme-defined Tay-Sachs disease carriers. These mutations do not result in any apparent clinical phenotype in individuals who are genetic compounds with a second disease-causing mutation. We expressed the {alpha}-subunit harboring each of the benign mutations separately to study activity toward the synthetic substrate, 4-MUGS, for comparison to activity from enzymes containing mutations associated with other forms of G{sub M2} gangliosidosis. The C739T (Arg247Trp;benign), C745T (Arg 249Trp; benign), G805A (Gly269Ser; adult-onset), G749A (Gly250Asp; juvenile), and C508T (Arg170Trp; infantile) mutations were introduced into the {alpha}-subunit cDNA. These were transfected alone, or with the {beta}-subunit cDNA, to generate Hex S ({alpha}{alpha}) or Hex A ({alpha}{beta}), respectively. The activities were monitored using 4-MUGS, and the levels of {alpha}-subunit protein were assessed by Western blotting. Repeated experiments show that the benign mutations produce approximately 35% of normal Hex S and 40% of normal Hex A activity. This level is much higher than that of Hex A harbouring the Gly169Ser adult-onset mutation (12%). A sequential decrease in expressed Hex A activity is observed as mutations associated with more severe phenotypes are expressed. The benign mutations also result in lower levels of mature {alpha}-subunit protein compared to normal, and slightly reduced levels of {alpha}-subunit precursor protein. The Hex A deficiency resulting from benign mutations is not as great as that associated with disease-causing mutations.

  20. Microstructure of selective laser melted CM247LC nickel-based superalloy and its evolution through heat treatment

    Energy Technology Data Exchange (ETDEWEB)

    Divya, V.D., E-mail: dv272@cam.ac.uk [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Muñoz-Moreno, R.; Messé, O.M.D.M.; Barnard, J.S. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Baker, S.; Illston, T. [Materials Solutions, Unit 8, Great Western Business Park, McKenzie Way, Worcester WR4 9GN (United Kingdom); Stone, H.J. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom)

    2016-04-15

    The selective laser melting of high temperature alloys is of great interest to the aerospace industry as it offers the prospect of producing more complex geometries than can be achieved with other manufacturing methods. In this study, the microstructure of the nickel-based superalloy, CM247LC, has been characterised following selective laser melting and after a post deposition heat treatment below the γ′ solvus temperature. In the as-deposited state, scanning electron microscopy with electron backscatter diffraction revealed a fine, cellular microstructure with preferential alignment of 〈001〉 along the build direction. A high dislocation density was seen at the periphery of the cells, indicating substantial localised deformation of the material. Fine primary MC carbides were also observed in the inter-cellular regions. High-resolution transmission electron microscopy identified the occurrence of very fine γ′ precipitates, approximately 5 nm in diameter, dispersed within the gamma phase. After heat treatment, the elongated cell colonies were observed to partially coalesce, accompanied by a decrease in dislocation density, producing columnar grains along the build direction. Cuboidal γ′ precipitates approximately 500 nm in diameter were observed to form in the recrystallised grains, accompanied by larger γ′ precipitates on the grain boundaries.

  1. Microstructure of selective laser melted CM247LC nickel-based superalloy and its evolution through heat treatment

    International Nuclear Information System (INIS)

    Divya, V.D.; Muñoz-Moreno, R.; Messé, O.M.D.M.; Barnard, J.S.; Baker, S.; Illston, T.; Stone, H.J.

    2016-01-01

    The selective laser melting of high temperature alloys is of great interest to the aerospace industry as it offers the prospect of producing more complex geometries than can be achieved with other manufacturing methods. In this study, the microstructure of the nickel-based superalloy, CM247LC, has been characterised following selective laser melting and after a post deposition heat treatment below the γ′ solvus temperature. In the as-deposited state, scanning electron microscopy with electron backscatter diffraction revealed a fine, cellular microstructure with preferential alignment of 〈001〉 along the build direction. A high dislocation density was seen at the periphery of the cells, indicating substantial localised deformation of the material. Fine primary MC carbides were also observed in the inter-cellular regions. High-resolution transmission electron microscopy identified the occurrence of very fine γ′ precipitates, approximately 5 nm in diameter, dispersed within the gamma phase. After heat treatment, the elongated cell colonies were observed to partially coalesce, accompanied by a decrease in dislocation density, producing columnar grains along the build direction. Cuboidal γ′ precipitates approximately 500 nm in diameter were observed to form in the recrystallised grains, accompanied by larger γ′ precipitates on the grain boundaries.

  2. Importance of the (n,gamma) Cm-247 Evaluation on Neutron Emission in Fast Reactor Fuel Cycle Analysis

    International Nuclear Information System (INIS)

    Benoit Forget; Mehdi Asgari; Rodolfo M. Ferrer

    2007-01-01

    As part of the GNEP program, it is envisioned to build a fast reactor for the transmutation of minor actinides. The spent nuclear fuel from the current fleet of light water reactors would be recycled, the current baseline is the UREX+1a process, and would act as a feed for the fast reactor. As the fuel is irradiated in a fast reactor a certain quantity of minor actinides would thus build up in the fuel stream creating possible concerns with the neutron emission of these minor actinides for fuel transportation, handling and fabrication. Past neutronic analyses had not tracked minor actinides above Cm-246 in the transmutation chain, because of the small influence on the overall reactor performance and cycle parameters. However, when trying to quantify the neutron emission from the recycled fuel with high minor actinide content, these higher isotopes play an essential role and should be included in the analysis. In this paper, the influence of tracking these minor actinides on the calculated neutron emission is presented. Also presented is the particular influence of choosing a different evaluated cross section data set to represent the minor actinides above Cm-246. The first representation uses the cross-sections provided by MC2-2 for all isotopes, while the second representation uses infinitely diluted ENDF/BVII.0 cross-sections for Cm-247 to Cf-252 and MC2-2 for all other isotopes

  3. Transplutonium elements production program: extraction chromatographic process for plutonium irradiated targets

    International Nuclear Information System (INIS)

    Bourges, J.; Madic, C.; Koehly, G.

    1980-01-01

    The treatment of irradiated plutonium targets by extraction chromatography allowed the purification of the isotopes 243 Am and 244 Cm on the scale of few tens of grams. This process proved to be extremely simple and flexible, and yielded results which are reproducible in time. The chief advantage of the TBP process over the HDEHP process in high and medium activity conditions lies in the rapid absorption/desorption kinetics of the elements to be purified and in the separation of americium from curium, which largely offsets its lower selectivity for lanthanide elements. it is certainly possible to improve the performance of this process by: a) optimization of the characteristics of the stationary phase, b) improvement in the filling technique and in hydraulic operation of the columns, c) on-line analysis of americium (the key element in actinide/lanthanide separation) in the eluate. The application of extraction chromatography with HD(DiBM)P to the purification of 243 Am of the end of treatment makes the process more consistent, eliminates the delicate stages implemented in hot cell, and considerably improves final product quality

  4. Perceptions of 24/7 In-house Attending Coverage on Fellow Education and Autonomy in a Pediatric Cardiothoracic Intensive Care Unit.

    Science.gov (United States)

    Owens, Sonal T; Owens, Gabe E; Rajput, Shaili H; Charpie, John R; Kidwell, Kelley M; Mullan, Patricia B

    2015-01-01

    The 24/7 in-house attending coverage is emerging as the standard of care in intensive care units. Implementation costs, workforce feasibility, and patient outcomes resulting from changes in physician staffing are widely debated topics. Understanding the impact of staffing models on the learning environment for medical trainees and faculty is equally warranted, particularly with respect to trainee education and autonomy. This study aims to elicit the perceptions of pediatric cardiology fellows and attendings toward 24/7 in-house attending coverage and its effect on fellow education and autonomy. We surveyed pediatric cardiology fellows and attendings practicing in the pediatric cardiothoracic intensive care unit (PCTU) of a large, university-affiliated medical center, using structured Likert response items and open-ended questions, prior to and following the transition to 24/7 in-house attending coverage. All (100%) trainees and faculty completed all surveys. Both prior to and following transition to 24/7 in-house attending coverage, all fellows, and the majority of attendings agreed that the overnight call experience benefited fellow education. At baseline, trainees identified limited circumstances in which on-site attending coverage would be critical. Preimplementation concerns that 24/7 in-house attending coverage would negatively affect the education of fellows were not reflected following actual implementation of the new staffing policy. However, based upon open-ended questions, fellow autonomy was affected by the new paradigm, with fellows and attendings reporting decreased "appropriateness" of autonomy after implementation. Our prospective study, showing initial concerns about limiting the learning environment in transitioning to 24/7 in-house attending coverage did not result in diminished perceptions of the educational experience for our fellows but revealed an expected decrease in fellow autonomy. The study indirectly facilitated open discussions about

  5. Targeted Learning

    CERN Document Server

    van der Laan, Mark J

    2011-01-01

    The statistics profession is at a unique point in history. The need for valid statistical tools is greater than ever; data sets are massive, often measuring hundreds of thousands of measurements for a single subject. The field is ready to move towards clear objective benchmarks under which tools can be evaluated. Targeted learning allows (1) the full generalization and utilization of cross-validation as an estimator selection tool so that the subjective choices made by humans are now made by the machine, and (2) targeting the fitting of the probability distribution of the data toward the targe

  6. Target preparation

    International Nuclear Information System (INIS)

    Hinn, G.M.

    1984-01-01

    A few of the more interesting of the 210 targets prepared in the Laboratory last year are listed. In addition the author continues to use powdered silver mixed with /sup 9,10/BeO to produce sources for accelerator radio dating of Alaskan and South Polar snow. Currently, he is trying to increase production by multiple sample processing. Also the author routinely makes 3 μg/cm 2 cracked slacked carbon stripper foils and is continuing research with some degree of success in making enriched 28 Si targets starting with the oxide

  7. HPLC MS/MS method for quantification of meprobamate in human plasma: application to 24/7 clinical toxicology.

    Science.gov (United States)

    Delavenne, Xavier; Gay-Montchamp, Jean Pierre; Basset, Thierry

    2011-01-15

    We described the development and full validation of rapid and accurate liquid chromatography method, coupled with tandem mass spectrometry detection, for quantification of meprobamate in human plasma with [(13)C-(2)H(3)]-meprobamate as internal standard. Plasma pretreatment involved a one-step protein precipitation with acetonitrile. Separation was performed by reversed-phase chromatography on a Luna MercuryMS C18 (20 mm×4 mm×3 μm) column using a gradient elution mode. The mobile phase was a mix of distilled water containing 0.1% formic acid and acetonitrile containing 0.1% formic acid. The selected reaction monitoring transitions, in electrospray positive ionization, used for quantification were 219.2→158.2 m/z and 223.1→161.1m/z for meprobamate and internal standard, respectively. Qualification transitions were 219.2→97.0 and 223.1→101.1 m/z for meprobamate and internal standard, respectively. The method was linear over the concentration range of 1-300 mg/L. The intra- and inter-day precision values were below 6.4% and accuracy was within 95.3% and 103.6% for all QC levels (5, 75 and 200 mg/L). The lower limit of quantification was 1 mg/L. Total analysis time was reduced to 6 min including sample preparation. The present method is successfully applied to 24/7 clinical toxicology and demonstrated its usefulness to detect meprobamate poisoning. Copyright © 2010 Elsevier B.V. All rights reserved.

  8. Development and pilot testing of 24/7 in-ambulance telemedicine for acute stroke : prehospital stroke study at the Universitair Ziekenhuis Brussel-project

    OpenAIRE

    Espinoza, Alexis Valenzuela; Van Hooff, Robbert-Jan; De Smedt, Ann; Moens, Maarten; Yperzeele, Laetitia; Nieboer, Koenraad; Hubloue, Ives; de Keyser, Jacques; Convents, Andre; Tellez, Helio Fernandez; Dupont, Alain; Putman, Koen; Brouns, Raf

    2016-01-01

    Abstract: Background: In-ambulance telemedicine is a recently developed and a promising approach to improve emergency care. We implemented the first ever 24/7 in-ambulance telemedicine service for acute stroke. We report on our experiences with the development and pilot testing of the Prehospital Stroke Study at the Universitair Ziekenhuis Brussel (PreSSUB) to facilitate a wider spread of the knowledge regarding this technique. Methods: Successful execution of the project involved the develop...

  9. Development and Pilot Testing of 24/7 In-Ambulance Telemedicine for Acute Stroke: Prehospital Stroke Study at the Universitair Ziekenhuis Brussel-Project

    OpenAIRE

    Espinoza, Alexis Valenzuela; Van Hooff, Robbert-Jan; De Smedt, Ann; Moens, Maarten; Yperzeele, Laetitia; Nieboer, Koenraad; Hubloue, Ives; de Keyser, Jacques; Convents, Andre; Tellez, Helio Fernandez; Dupont, Alain; Putman, Koen; Brouns, Raf

    2016-01-01

    Background: In-ambulance telemedicine is a recently developed and a promising approach to improve emergency care. We implemented the first ever 24/7 in-ambulance telemedicine service for acute stroke. We report on our experiences with the development and pilot testing of the Prehospital Stroke Study at the Universitair Ziekenhuis Brussel (PreSSUB) to facilitate a wider spread of the knowledge regarding this technique. Methods: Successful execution of the project involved the development and v...

  10. The role of continuous monitoring in a 24/7 telecardiology consultation service--a feasibility study.

    Science.gov (United States)

    Nikus, Kjell; Lähteenmäki, Jaakko; Lehto, Pasi; Eskola, Markku

    2009-01-01

    for speeding up the diagnostic and therapeutic processes in the hospital, although the study was limited in that the telecardiologist played a passive role and did not acutely impact patient care. In the future, the system could be expanded to surveillance of smaller hospitals. Telemedicine has the potential to aid in solving the conflict between aging of population, rise in the demand for critical care services, and shortage of professional personnel. This might, however, require a more active remote surveillance than the one tested in this study. Privacy- and security-related aspects are major components of building trust and confidence in telemedicine systems. In telecardiology, the real-time interactive telemedicine model with 24/7 service has potential superior performance compared with a store-and-forward telemedicine model.

  11. 24/7 Connectedness and its Potential Impact on Today’s Physics Students: Technology Use, Multitasking, and GenMe

    OpenAIRE

    Teresa L. Larkin; Benjamin R. Hein

    2018-01-01

    There is no question that the digital age is upon us. For many of us, the trans-formation to the digital age has been gradual; and, most often, welcomed. In the classroom, we have developed many useful and innovative applications technolo-gy-based pedagogies. Outside of the classroom, we use routinely rely on tech-nology to communicate with our students. However, not all of us grew up with 24/7 access to information that the internet and today’s technologies provide. Perhaps the impact o...

  12. LA SENTENCIA DEL TRIBUNAL CONSTITUCIONAL 247/2007 Y EL SISTEMA CONSTITUCIONAL DE DISTRIBUCIÓN DE COMPETENCIAS ENTRE EL ESTADO Y LAS COMUNIDADES AUTÓNOMAS

    Directory of Open Access Journals (Sweden)

    Joaquín Tornos Mas

    2008-10-01

    Full Text Available The aim of this study is to examine articles 7 to 10 of ruling 247/2007 of theConstitutional Court, in which the role of the Statutes of Autonomy in thedivision of jurisdictions between the Central Government and the AutonomousCommunities is analysed, and the impact that the ruling in this case may haveon the future ruling on the Catalan Statute. To link ruling 247/2007 withthe future ruling on the Catalan Statute, on one side the appellant parties –the Partido Popular and the ombudsman, and the Parliement of Catalonia,on the other, the Constitutional Court makes its arguments regarding theextent to which the Statutes of Autonomy limit its jurisdiction. Public knowledgeof the appellants’ arguments and the Constitutional Court’s decisionregarding this case, which are included in a ruling from previous appealsthat pronounces on many of the issues covered in the mentioned appeals,allows the study to close with a series of considerations about the future rulingof the Constitutional Court on the part of the Catalan Statute relatingto the new model for distribution of jurisdictions.

  13. 24/7 Connectedness and its Potential Impact on Today’s Physics Students: Technology Use, Multitasking, and GenMe

    Directory of Open Access Journals (Sweden)

    Teresa L. Larkin

    2018-05-01

    Full Text Available There is no question that the digital age is upon us. For many of us, the trans-formation to the digital age has been gradual; and, most often, welcomed. In the classroom, we have developed many useful and innovative applications technolo-gy-based pedagogies. Outside of the classroom, we use routinely rely on tech-nology to communicate with our students. However, not all of us grew up with 24/7 access to information that the internet and today’s technologies provide. Perhaps the impact of technology on those of us that teach is a bit different from the impact on our students. Many of our students today are members of the mil-lennial generation, which is sometimes referred to as Generation Me (GenMe. Members of GenMe have literally grown up with technology and the instantane-ous availability of information right at their fingertips. Computers, smart phones, iPads, and other technologies offer their users immediate access to information. Might these technologies be seen as a significant distraction to whatever the task at hand might be? Could these distractions be to blame for the perception of many in GenMe that they must multitask in order to get everything done? Might instant access to information be casting a cloud on student learning? If so, does this cloud have a silver lining? This paper addresses these and other questions through the use of a survey given to students in a second-level physics course in spring 2016. Results reveal that nearly all students feel the need to maintain this 24/7 connection using their smart phones. The impact that this level of connect-edness may have on our students will be discussed.

  14. The multifaceted effects of agmatine on functional recovery after spinal cord injury through Modulations of BMP-2/4/7 expressions in neurons and glial cells.

    Directory of Open Access Journals (Sweden)

    Yu Mi Park

    Full Text Available Presently, few treatments for spinal cord injury (SCI are available and none have facilitated neural regeneration and/or significant functional improvement. Agmatine (Agm, a guanidinium compound formed from decarboxylation of L-arginine by arginine decarboxylase, is a neurotransmitter/neuromodulator and been reported to exert neuroprotective effects in central nervous system injury models including SCI. The purpose of this study was to demonstrate the multifaceted effects of Agm on functional recovery and remyelinating events following SCI. Compression SCI in mice was produced by placing a 15 g/mm(2 weight for 1 min at thoracic vertebra (Th 9 segment. Mice that received an intraperitoneal (i.p. injection of Agm (100 mg/kg/day within 1 hour after SCI until 35 days showed improvement in locomotor recovery and bladder function. Emphasis was made on the analysis of remyelination events, neuronal cell preservation and ablation of glial scar area following SCI. Agm treatment significantly inhibited the demyelination events, neuronal loss and glial scar around the lesion site. In light of recent findings that expressions of bone morphogenetic proteins (BMPs are modulated in the neuronal and glial cell population after SCI, we hypothesized whether Agm could modulate BMP- 2/4/7 expressions in neurons, astrocytes, oligodendrocytes and play key role in promoting the neuronal and glial cell survival in the injured spinal cord. The results from computer assisted stereological toolbox analysis (CAST demonstrate that Agm treatment dramatically increased BMP- 2/7 expressions in neurons and oligodendrocytes. On the other hand, BMP- 4 expressions were significantly decreased in astrocytes and oligodendrocytes around the lesion site. Together, our results reveal that Agm treatment improved neurological and histological outcomes, induced oligodendrogenesis, protected neurons, and decreased glial scar formation through modulating the BMP- 2/4/7 expressions following

  15. The Multifaceted Effects of Agmatine on Functional Recovery after Spinal Cord Injury through Modulations of BMP-2/4/7 Expressions in Neurons and Glial Cells

    Science.gov (United States)

    Park, Yu Mi; Lee, Won Taek; Bokara, Kiran Kumar; Seo, Su Kyoung; Park, Seung Hwa; Kim, Jae Hwan; Yenari, Midori A.; Park, Kyung Ah; Lee, Jong Eun

    2013-01-01

    Presently, few treatments for spinal cord injury (SCI) are available and none have facilitated neural regeneration and/or significant functional improvement. Agmatine (Agm), a guanidinium compound formed from decarboxylation of L-arginine by arginine decarboxylase, is a neurotransmitter/neuromodulator and been reported to exert neuroprotective effects in central nervous system injury models including SCI. The purpose of this study was to demonstrate the multifaceted effects of Agm on functional recovery and remyelinating events following SCI. Compression SCI in mice was produced by placing a 15 g/mm2 weight for 1 min at thoracic vertebra (Th) 9 segment. Mice that received an intraperitoneal (i.p.) injection of Agm (100 mg/kg/day) within 1 hour after SCI until 35 days showed improvement in locomotor recovery and bladder function. Emphasis was made on the analysis of remyelination events, neuronal cell preservation and ablation of glial scar area following SCI. Agm treatment significantly inhibited the demyelination events, neuronal loss and glial scar around the lesion site. In light of recent findings that expressions of bone morphogenetic proteins (BMPs) are modulated in the neuronal and glial cell population after SCI, we hypothesized whether Agm could modulate BMP- 2/4/7 expressions in neurons, astrocytes, oligodendrocytes and play key role in promoting the neuronal and glial cell survival in the injured spinal cord. The results from computer assisted stereological toolbox analysis (CAST) demonstrate that Agm treatment dramatically increased BMP- 2/7 expressions in neurons and oligodendrocytes. On the other hand, BMP- 4 expressions were significantly decreased in astrocytes and oligodendrocytes around the lesion site. Together, our results reveal that Agm treatment improved neurological and histological outcomes, induced oligodendrogenesis, protected neurons, and decreased glial scar formation through modulating the BMP- 2/4/7 expressions following SCI. PMID

  16. Heavy-ion targets

    International Nuclear Information System (INIS)

    Adair, H.L.; Kobisk, E.H.

    1985-01-01

    This chapter examines the characteristics of targets required in heavy-ion accelerator physics experiments. The effects of target parameters on heavy-ion experimental results are reviewed. The target fabrication and characterization techniques used to minimize experimental problems during heavy-ion bombardment are described. Topics considered include target thickness and uniformity, target lifetime, target purity, substrate materials, Doppler shift effects, metal preparations, and target preparation methods

  17. Characteristics of food industry web sites and "advergames" targeting children.

    Science.gov (United States)

    Culp, Jennifer; Bell, Robert A; Cassady, Diana

    2010-01-01

    To assess the content of food industry Web sites targeting children by describing strategies used to prolong their visits and foster brand loyalty; and to document health-promoting messages on these Web sites. A content analysis was conducted of Web sites advertised on 2 children's networks, Cartoon Network and Nickelodeon. A total of 290 Web pages and 247 unique games on 19 Internet sites were examined. Games, found on 81% of Web sites, were the most predominant promotion strategy used. All games had at least 1 brand identifier, with logos being most frequently used. On average Web sites contained 1 "healthful" message for every 45 exposures to brand identifiers. Food companies use Web sites to extend their television advertising to promote brand loyalty among children. These sites almost exclusively promoted food items high in sugar and fat. Health professionals need to monitor food industry marketing practices used in "new media." Published by Elsevier Inc.

  18. F247. INTERNALIZED STIGMA HAS A STRONGER RELATIONSHIP WITH INTRINSIC MOTIVATION COMPARED TO AMOTIVATION IN EARLY PHASE AND PROLONGED SCHIZOPHRENIA

    Science.gov (United States)

    Firmin, Ruth; Luther, Lauren; Lysaker, Paul; Vohs, Jennifer

    2018-01-01

    Abstract Background Motivation deficits predict decreased functioning in schizophrenia. Recent work suggests deficits reflect challenges in separate domains: intrinsic motivation (one’s internal drive to engage in a behavior out of enjoyment or interest) and amotivation (one’s broader decrease in motivated behavior linked to avolition and anhedonia). Internalized stigma is another determinant of functioning for people with schizophrenia that may impact motivation. However, little is known about these relationships, including which aspects of motivation it may impact nor when these links emerge. Identifying the link between these constructs may help to identify whether internalized stigma may be a novel treatment target to facilitate improvements in motivation. Methods Forty adults with early phase schizophrenia and 66 adults with prolonged schizophrenia completed measures of internalized stigma, intrinsic motivation, and amotivation. Pearson’s correlations were examined followed by Fischer’s r-to-z transformations to compare differences in the magnitude of associations between internalized stigma and intrinsic motivation and internalized stigma and amotivation among the first episode and prolonged samples. Next, we conducted stepwise regressions to examine whether internalized stigma was associated with intrinsic motivation above and beyond associations with amotivation in each sample. Results In the early phase sample, the association between internalized stigma was greater with intrinsic motivation (r=-0.48, p=.00) compared to amotivation (r=0.27, p=0.10). Associations with internalized stigma in the prolonged sample were also greater with intrinsic motivation (r=-0.30, p=0.02) versus amotivation (r=0.19, p=0.12). The magnitude of the associations between internalized stigma and intrinsic motivation (z=1.03, p=0.15) and between internalized stigma and amotivation (z=0.41, p = 0.34) did not significantly differ when comparing phase of illness. Regression

  19. Organelle targeting: third level of drug targeting

    Directory of Open Access Journals (Sweden)

    Sakhrani NM

    2013-07-01

    Full Text Available Niraj M Sakhrani, Harish PadhDepartment of Cell and Molecular Biology, BV Patel Pharmaceutical Education and Research Development (PERD Centre, Gujarat, IndiaAbstract: Drug discovery and drug delivery are two main aspects for treatment of a variety of disorders. However, the real bottleneck associated with systemic drug administration is the lack of target-specific affinity toward a pathological site, resulting in systemic toxicity and innumerable other side effects as well as higher dosage requirement for efficacy. An attractive strategy to increase the therapeutic index of a drug is to specifically deliver the therapeutic molecule in its active form, not only into target tissue, nor even to target cells, but more importantly, into the targeted organelle, ie, to its intracellular therapeutic active site. This would ensure improved efficacy and minimize toxicity. Cancer chemotherapy today faces the major challenge of delivering chemotherapeutic drugs exclusively to tumor cells, while sparing normal proliferating cells. Nanoparticles play a crucial role by acting as a vehicle for delivery of drugs to target sites inside tumor cells. In this review, we spotlight active and passive targeting, followed by discussion of the importance of targeting to specific cell organelles and the potential role of cell-penetrating peptides. Finally, the discussion will address the strategies for drug/DNA targeting to lysosomes, mitochondria, nuclei and Golgi/endoplasmic reticulum.Keywords: intracellular drug delivery, cancer chemotherapy, therapeutic index, cell penetrating peptides

  20. LARGE SCALE METHOD FOR THE PRODUCTION AND PURIFICATION OF CURIUM

    Science.gov (United States)

    Higgins, G.H.; Crane, W.W.T.

    1959-05-19

    A large-scale process for production and purification of Cm/sup 242/ is described. Aluminum slugs containing Am are irradiated and declad in a NaOH-- NaHO/sub 3/ solution at 85 to 100 deg C. The resulting slurry filtered and washed with NaOH, NH/sub 4/OH, and H/sub 2/O. Recovery of Cm from filtrate and washings is effected by an Fe(OH)/sub 3/ precipitation. The precipitates are then combined and dissolved ln HCl and refractory oxides centrifuged out. These oxides are then fused with Na/sub 2/CO/sub 3/ and dissolved in HCl. The solution is evaporated and LiCl solution added. The Cm, rare earths, and anionic impurities are adsorbed on a strong-base anfon exchange resin. Impurities are eluted with LiCl--HCl solution, rare earths and Cm are eluted by HCl. Other ion exchange steps further purify the Cm. The Cm is then precipitated as fluoride and used in this form or further purified and processed. (T.R.H.)

  1. Gastrointestinal absorption of neptunium and curium in humans

    International Nuclear Information System (INIS)

    Popplewell, D.S.; Harrison, J.D.; Ham, G.J.

    1991-01-01

    The gastrointestinal absorption of Np and Cm has been determined in five male adult volunteers. The Np and Cm, which were in citrate solution, were taken with food. An initial experiment with each individual determined the fraction of each element excreted in the urine following intravenous administration. Subsequently, the results for urinary excretion for the two routes of administration were used to calculate the fractional absorption (f1) of ingested Np and Cm. The mean f1 values were: Np (2.0 +/- 0.2) X 10 - 4 , range (1.2-2.9) X 10 - 4 , and Cm (1.7 +/- 0.3) X 10 - 4 , range (0.95-3.0) X 10 - 4 , the quoted uncertainties being the standard error of the means. Currently, the International Commission on Radiological Protection recommends a value of 10 - 3 for both elements. Cumulative urinary excretion over 1 wk after intravenous injection accounted for about 20%-40% of administered Np and 7%-10% of Cm. At the conclusion of the experiment, the total committed effective dose equivalent for each volunteer was calculated to be in the range 130-250 microSv, based on the individual f1 values, and, in some cases, a knowledge of the rate of clearance of 239 Np through the gut as measured by whole-body counting

  2. Interaction of europium and curium with alpha-amylase

    Energy Technology Data Exchange (ETDEWEB)

    Barkleit, Astrid [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Chemistry of the F-Elements; Heller, Anne [Technische Univ. Dresden (Germany). Inst. for Zoology, Molecular Cell Physiology and Endocrinology; Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Div. Biogeochemistry

    2016-07-01

    Time-resolved laser-induced fluorescence spectroscopy (TRLFS) revealed that Eu(III) and Cm(III) form two dominant species with the protein α-amylase (Amy): one with the coordination of a single carboxylate group of the protein and the other with three coordinating carboxylate groups.

  3. Removal of americium and curium from high-level wastes

    International Nuclear Information System (INIS)

    Bond, W.D.; Leuze, R.E.

    1979-01-01

    The DHDECMP process was demonstrated to give a 99.5% removal of actinides from actual HLLW in small-scale, batch extraction tests. Results from cold tests indicate that it may be possible to carry out the oxalate precipitation step of the OPIX process continuously. About 90% recovery of the trivalent actinides and lanthanides can be achieved in the continuous precipitation. the presence of zirconium impurity in feed solutions to Talspeak process at concentrations of 10 -4 M (0.5% of the Zr in the original waste) affected phase separations but equipment could be operated satisfactory in cold tests. Zirconium concentrations of 10 -3 M seriously affected phase separations and substantial quantities of interfacial cruds were formed. Modest concentrations (0.006 M or less) of H 2 MEHP, a suspected degradation product of HDEHP, did not effect separation factors. The presence of impurities derived from the thermal degradation of DHDECMP did not inhibit the loading of the trivalent actinide and lanthanide elements in the cation exchange chromatographic process for their separation. It appears that the biodentate (DHDECMP) solvent extraction process and the OPIX process are the leading candidate process for the co-removal of trivalent actinide and lanthanide elements from HLLW. The cation exchange chromatography and the Talspeak processes, are the leading candidate processes for the subsequent separation of actinides and lanthanides. The bidentate and cation exchange processes are further along in their development than the other processes and are currently considered the reference processes for the partitioning of Am-Cm from HLLW. 4 figures, 4 tables

  4. A bioassay method for americium and curium in feces

    International Nuclear Information System (INIS)

    Alexandre Gagne; Dominic Lariviere; Joel Surette; Sheila Kramer-Tremblay; Xiongxin Dai; Candice Didychuk

    2013-01-01

    Fecal radiobioassay is an essential and sensitive tool to estimate the internal intake of actinides after a radiological incident. A new fecal analysis method, based on lithium metaborate fusion of fecal ash for complete sample dissolution followed by sequential column chromatography separation of actinides, has been developed for the determination of low-level Am and Cm in a large size sample. Spiked synthetic fecal samples were analyzed to evaluate method performance against the acceptance criteria for radiobioassay as defined by ANSI N13.30; both satisfactory accuracy and repeatability were achieved. This method is a promising candidate for reliable dose assessment of low level actinide exposure to meet the regulatory requirements of routine radiobioassay for nuclear workers and the public. (author)

  5. Structural Benchmark Creep Testing for Microcast MarM-247 Advanced Stirling Convertor E2 Heater Head Test Article SN18

    Science.gov (United States)

    Krause, David L.; Brewer, Ethan J.; Pawlik, Ralph

    2013-01-01

    This report provides test methodology details and qualitative results for the first structural benchmark creep test of an Advanced Stirling Convertor (ASC) heater head of ASC-E2 design heritage. The test article was recovered from a flight-like Microcast MarM-247 heater head specimen previously used in helium permeability testing. The test article was utilized for benchmark creep test rig preparation, wall thickness and diametral laser scan hardware metrological developments, and induction heater custom coil experiments. In addition, a benchmark creep test was performed, terminated after one week when through-thickness cracks propagated at thermocouple weld locations. Following this, it was used to develop a unique temperature measurement methodology using contact thermocouples, thereby enabling future benchmark testing to be performed without the use of conventional welded thermocouples, proven problematic for the alloy. This report includes an overview of heater head structural benchmark creep testing, the origin of this particular test article, test configuration developments accomplished using the test article, creep predictions for its benchmark creep test, qualitative structural benchmark creep test results, and a short summary.

  6. Live birth sex ratio after in vitro fertilization and embryo transfer in China--an analysis of 121,247 babies from 18 centers.

    Science.gov (United States)

    Bu, Zhiqin; Chen, Zi-Jiang; Huang, Guoning; Zhang, Hanwang; Wu, Qiongfang; Ma, Yanping; Shi, Juanzi; Xu, Yanwen; Zhang, Songying; Zhang, Cuilian; Zhao, Xiaoming; Zhang, Bo; Huang, Yuanhua; Sun, Zhengyi; Kang, Yuefan; Wu, Riran; Wu, Xueqing; Sun, Haixiang; Sun, Yingpu

    2014-01-01

    In order to study the impact of procedures of IVF/ICSI technology on sex ratio in China, we conducted this multi-center retrospective study including 121,247 babies born to 93,895 women in China. There were 62,700 male babies and 58,477 female babies, making the sex ratio being 51.8% (Male: Female  = 107:100). In univariate logistic regression analysis, sex ratio was imbalance toward females of 50.3% when ICSI was preformed compared to 47.7% when IVF was used (Pratio in IVF/ICSI babies was significantly higher toward males in transfers of blastocyst (54.9%) and thawed embryo (52.4%) when compared with transfers of cleavage stage embryo (51.4%) and fresh embryo (51.5%), respectively. Multiple delivery was not associated with sex ratio. However, in multivariable logistic regression analysis after controlling for related factors, only ICSI (adjusted OR =  .90, 95%CI: 0.88-0.93; Pratio in IVF/ICSI babies. In conclusion, the live birth sex ratio in IVF/ICSI babies was influenced by the use of ICSI, which may decrease the percentage of male offspring, or the use of blastocyst transfer, which may increase the percentage of male offspring.

  7. Effect of heat treatment on the microstructure, texture and elastic anisotropy of the nickel-based superalloy CM247LC processed by selective laser melting

    International Nuclear Information System (INIS)

    Muñoz-Moreno, R.; Divya, V.D.; Driver, S.L.; Messé, O.M.D.M.; Illston, T.; Baker, S.; Carpenter, M.A.; Stone, H.J.

    2016-01-01

    Selective laser melting (SLM) of nickel-based superalloys is of great interest for the aerospace industry due to its capability for producing components with complex geometries. However, an improved understanding of the effect of SLM and subsequent post deposition heat treatments on the microstructure and mechanical properties is required to ensure that components with good structural integrity are produced. In this study, the microstructure, texture and elastic anisotropy of the nickel-based superalloy, CM247LC, in the as-SLM and heat-treated states have been analysed. The as-SLM microstructure showed fine elongated cells with a preferential alignment of <001> along the build direction and a significant intercellular misorientation. Heat treatments at temperatures below 1230 °C resulted in a progressive recovery of the microstructure, whilst heat treatments above this temperature gave rise to a recrystallised microstructure. The extent to which nucleation and growth of the γ′ precipitates and secondary particles were affected by increasing the heat treatment temperature was also characterised. The bulk elastic anisotropy of all samples was measured by resonant ultrasound spectroscopy (RUS) and was found to be consistent with the local textures obtained by electron backscatter diffraction (EBSD). It was observed that the initially strong elastic anisotropy exhibited by the as-SLM material was significantly reduced in the recrystallised samples, although some anisotropy was retained as a result of their elongated grain microstructures.

  8. Effect of heat treatment on the microstructure, texture and elastic anisotropy of the nickel-based superalloy CM247LC processed by selective laser melting

    Energy Technology Data Exchange (ETDEWEB)

    Muñoz-Moreno, R., E-mail: rociomunozmoreno@gmail.com [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Divya, V.D. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Driver, S.L. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Department of Earth Sciences, University of Cambridge, Downing Street, Cambridge CB2 3EQ (United Kingdom); Messé, O.M.D.M. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Illston, T.; Baker, S. [Materials Solutions, Unit 8, Great Western Business Park, McKenzie Way, Worcester WR4 9GN (United Kingdom); Carpenter, M.A. [Department of Earth Sciences, University of Cambridge, Downing Street, Cambridge CB2 3EQ (United Kingdom); Stone, H.J. [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom)

    2016-09-30

    Selective laser melting (SLM) of nickel-based superalloys is of great interest for the aerospace industry due to its capability for producing components with complex geometries. However, an improved understanding of the effect of SLM and subsequent post deposition heat treatments on the microstructure and mechanical properties is required to ensure that components with good structural integrity are produced. In this study, the microstructure, texture and elastic anisotropy of the nickel-based superalloy, CM247LC, in the as-SLM and heat-treated states have been analysed. The as-SLM microstructure showed fine elongated cells with a preferential alignment of <001> along the build direction and a significant intercellular misorientation. Heat treatments at temperatures below 1230 °C resulted in a progressive recovery of the microstructure, whilst heat treatments above this temperature gave rise to a recrystallised microstructure. The extent to which nucleation and growth of the γ′ precipitates and secondary particles were affected by increasing the heat treatment temperature was also characterised. The bulk elastic anisotropy of all samples was measured by resonant ultrasound spectroscopy (RUS) and was found to be consistent with the local textures obtained by electron backscatter diffraction (EBSD). It was observed that the initially strong elastic anisotropy exhibited by the as-SLM material was significantly reduced in the recrystallised samples, although some anisotropy was retained as a result of their elongated grain microstructures.

  9. Deuterium pass through target

    International Nuclear Information System (INIS)

    Alger, D.L.

    1975-01-01

    A neutron emitting target is described for use in neutron generating apparatus including a deuteron source and an accelerator vacuum chamber. The target consists of a tritium-containing target layer, a deuteron accumulation layer, and a target support containing passages providing communication between the accumulation layer and portions of the surface of the support exposed to the accelerator vacuum chamber. With this arrangement, deuterons passing through the target layer and implanting in and diffusing through the accumulation layer, diffuse into the communicating passages and are returned to the accelerator vacuum chamber. The invention allows the continuous removal of deuterons from the target in conventional water cooled neutron generating apparatus. Preferably, the target is provided with thin barrier layers to prevent undesirable tritium diffusion out of the target layer, as well as deuteron diffusion into the target layer

  10. Molecular Targets for Targeted Radionuclide Therapy

    International Nuclear Information System (INIS)

    Mather, S.J.

    2009-01-01

    Molecular targeted radionuclide cancer therapy is becoming of increasing importance, especially for disseminated diseases. Systemic chemotherapies often lack selectivity while targeted radionuclide therapy has important advantages as the radioactive cytotoxic unit of the targeting vector is specifically directed to the cancer, sparing normal tissues. The principle strategy to improve cancer selectivity is to couple therapeutic agents to tumour-targeting vectors. In targeted radionuclide therapy (TRT), the cytotoxic portion of the conjugates normally contains a therapeutic radiometal immobilised by a bifunctional chelator. The aim is therefore to use as ligand-targeted therapeutics vectors coupled to Auger-, alpha- and/or beta-emitting radionuclides. An advantage of using radiation instead of chemotherapeutics as the cytotoxic agent is the so called 'crossfire effect'. This allows sterilisation of tumour cells that are not directly targeted due to heterogeneity in target molecule expression or inhomogeneous vector delivery. However, before the targeting ligands can be selected, the target molecule on the tumour has to be selected. It should be uniquely expressed, or at least highly overexpressed, on or in the target cells relative to normal tissues. The target should be easily accessible for ligand delivery and should not be shed or down- regulated after ligand binding. An important property of a receptor (or antigen) is its potential to be internalized upon binding of the ligand. This provides an active uptake mechanism and allows the therapeutic agent to be trapped within the tumour cells. Molecular targets of current interest include: Receptors: G-protein coupled receptors are overexpressed on many major human tumours. The prototype of these receptors are somatostatin receptors which show very high density in neuroendocrine tumours, but there are many other most interesting receptors to be applied for TRT. The targeting ligands for these receptors are

  11. Monitoring production target thickness

    International Nuclear Information System (INIS)

    Oothoudt, M.A.

    1993-01-01

    Pion and muon production targets at the Clinton P. Anderson Meson Physics Facility consist of rotating graphite wheels. The previous target thickness monitoring Procedure scanned the target across a reduced intensity beam to determine beam center. The fractional loss in current across the centered target gave a measure of target thickness. This procedure, however, required interruption of beam delivery to experiments and frequently indicated a different fractional loss than at normal beam currents. The new monitoring Procedure compares integrated ups and downs toroid current monitor readings. The current monitors are read once per minute and the integral of readings are logged once per eight-hour shift. Changes in the upstream to downstream fractional difference provide a nonintrusive continuous measurement of target thickness under nominal operational conditions. Target scans are now done only when new targets are installed or when unexplained changes in the current monitor data are observed

  12. Charged particle fusion targets

    International Nuclear Information System (INIS)

    Bangerter, R.O.; Meeker, D.J.

    1977-01-01

    The power, voltage, energy and other requirements of electron and ion beam fusion targets are reviewed. Single shell, multiple shell and magnetically insulated target designs are discussed. Questions of stability are also considered. In particular, it is shown that ion beam targets are stabilized by an energy spread in the ion beam

  13. Liquid helium target

    International Nuclear Information System (INIS)

    Fujii, Y.; Kitami, T.; Torikoshi, M.

    1984-12-01

    A liquid helium target system has been built and used for the experiment on the reaction 4 He(γ, p). The target system has worked satisfactorily; the consumption rate of liquid helium is 360 ml/h and the cryogenic system retains liquid helium for about ten hours. The structure, operation and performance of the target system are reported. (author)

  14. Graphite targets at LAMPF

    International Nuclear Information System (INIS)

    Brown, R.D.; Grisham, D.L.

    1983-01-01

    Rotating polycrystalline and stationary pyrolytic graphite target designs for the LAMPF experimental area are described. Examples of finite element calculations of temperatures and stresses are presented. Some results of a metallographic investigation of irradiated pyrolytic graphite target plates are included, together with a brief description of high temperature bearings for the rotating targets

  15. 24/7 Presence of Medical Staff in the Labor Ward; No Day-Night Differences in Perinatal and Maternal Outcomes.

    Science.gov (United States)

    Tavares, Sara; Cavaco-Gomes, João; Moucho, Marina; Severo, Milton; Mateus, Mário; Ramalho, Carla; Visser, Gerard H A; Montenegro, Nuno

    2017-05-01

    Objective  The objective of this study was to assess possible day-night differences in perinatal and maternal labor outcomes in a hospital setting with no day-night differences in the presence of experienced medical staff. Design  This was a retrospective study conducted over 5 years between 2008 and 2012. Setting  This study was set at the obstetric delivery unit in a tertiary hospital. Population  A total of 9,143 singleton deliveries were assessed after 34 weeks of gestation and after exclusion of major congenital malformations, inductions of labor, and elective cesarean sections. Materials and Methods  Data were collected using the hospital electronic medical records. Time periods of 8 hours were defined (daytime between 8 am and 4 pm, evening time between 4 pm and 12 pm, and nighttime between 12 pm and 8 am). Differences between the three time periods were assessed using software R Core Team (2013). Main outcome measures were neonatal birth asphyxia, neonatal intensive care unit admission, and neonatal death. Results  There were no differences in perinatal and maternal outcomes in the course of the day, apart from a higher incidence of third- and fourth-degree tears during the evening. Neonatal outcome after obstetric emergencies (uterine rupture, partial placental abruption, and cord prolapse) also showed no day-night differences. Conclusion  Adverse nighttime-related outcomes may be avoided by the 24/7 presence of experienced medical staff. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

  16. Wake Shield Target Protection

    International Nuclear Information System (INIS)

    Valmianski, Emanuil I.; Petzoldt, Ronald W.; Alexander, Neil B.

    2003-01-01

    The heat flux from both gas convection and chamber radiation on a direct drive target must be limited to avoid target damage from excessive D-T temperature increase. One of the possibilities of protecting the target is a wake shield flying in front of the target. A shield will also reduce drag force on the target, thereby facilitating target tracking and position prediction. A Direct Simulation Monte Carlo (DSMC) code was used to calculate convection heat loads as boundary conditions input into ANSYS thermal calculations. These were used for studying the quality of target protection depending on various shapes of shields, target-shield distance, and protective properties of the shield moving relative to the target. The results show that the shield can reduce the convective heat flux by a factor of 2 to 5 depending on pressure, temperature, and velocity. The protective effect of a shield moving relative to the target is greater than the protective properties of a fixed shield. However, the protective effect of a shield moving under the drag force is not sufficient for bringing the heat load on the target down to the necessary limit. Some other ways of diminishing heat flux using a protective shield are discussed

  17. Development of distributed target

    CERN Document Server

    Yu Hai Jun; Li Qin; Zhou Fu Xin; Shi Jin Shui; Ma Bing; Chen Nan; Jing Xiao Bing

    2002-01-01

    Linear introduction accelerator is expected to generate small diameter X-ray spots with high intensity. The interaction of the electron beam with plasmas generated at the X-ray converter will make the spot on target increase with time and debase the X-ray dose and the imaging resolving power. A distributed target is developed which has about 24 pieces of thin 0.05 mm tantalum films distributed over 1 cm. due to the structure adoption, the distributed target material over a large volume decreases the energy deposition per unit volume and hence reduces the temperature of target surface, then reduces the initial plasma formalizing and its expansion velocity. The comparison and analysis with two kinds of target structures are presented using numerical calculation and experiments, the results show the X-ray dose and normalized angle distribution of the two is basically the same, while the surface of the distributed target is not destroyed like the previous block target

  18. Polarized targets and beams

    International Nuclear Information System (INIS)

    Meyer, W.

    1985-01-01

    First the experimental situation of the single-pion photoproduction and the photodisintegration of the deuteron is briefly discussed. Then a description of the Bonn polarization facilities is given. The point of main effort is put on the polarized target which plays a vital role in the program. A facility for photon induced double polarization experiments at ELSA will be presented in section 4. Properties of a tensor polarized deuteron target are discussed in section 5. The development in the field of polarized targets, especially on new target materials, enables a new generation of polarized target experiments with (polarized) electrons. Some comments on the use of a polarized target in combination with electron beams will be discussed in section 6. Electron deuteron scattering from a tensor polarized deuteron target is considered and compared with other experimental possibilities. (orig./HSI)

  19. Nova target experiments

    International Nuclear Information System (INIS)

    Drake, R.P.

    1985-11-01

    The Nova laser, at the Lawrence Livermore National Laboratory, provides unique opportunities for target experiments. It has unprecedented energy on target and significant flexibility. The paper presented by John Hunt described the capabilities and the status of Nova. This paper discusses plans for future experiments using Nova, and the present status of target experiments. We plan to perform high-quality physics experiments that exploit the unique capabilities of Nova. Because this is our goal, we are fielding an extensive array of well-characterized target diagnostics to measure the emissions from the target. The first section of this paper discusses the basic target diagnostics. We are also taking care to quantify the performance of the laser

  20. Targeting and Persuasive Advertising

    OpenAIRE

    Egli, Alain (Autor/in)

    2015-01-01

    Firms face a prisoner's dilemma when advertising in a competitive environment. In a Hotelling framework with persuasive advertisingfirms counteract this prisoner's dilemma with targeting. The firms even solve the prisoner's problem if targeted advertising is effective enough. Advertising turns from wasteful competition into profits. This is in contrast to wasteful competition as argument for regulations. A further result is maximum advertising differentiation: thefirms target their advertisin...

  1. The ISOLDE target robots

    CERN Multimedia

    Maximilein Brice

    2002-01-01

    ISOLDE targets need to be changed frequently, around 80 times per year. The high radiation levels do not permit this to be done by human hands and the target changes are effected by 2 industrial robots (picture _01). On the left, in the distance, the front-end of the GPS (General Purpose Separator) is seen, while the HRS (High Resolution Separator) is at the right. Also seen are the doors to the irradiated-target storage.

  2. Deuterium high pressure target

    International Nuclear Information System (INIS)

    Perevozchikov, V.V.; Yukhimchuk, A.A.; Vinogradov, Yu.I.

    2001-01-01

    The design of the deuterium high-pressure target is presented. The target having volume of 76 cm 3 serves to provide the experimental research of muon catalyzed fusion reactions in ultra-pure deuterium in the temperature range 80-800 K under pressures of up to 150 MPa. The operation of the main systems of the target is described: generation and purification of deuterium gas, refrigeration, heating, evacuation, automated control system and data collection system

  3. Targeted Radionuclide Therapy

    Directory of Open Access Journals (Sweden)

    David Cheng

    2011-10-01

    Full Text Available Targeted radiotherapy is an evolving and promising modality of cancer treatment. The killing of cancer cells is achieved with the use of biological vectors and appropriate radionuclides. Among the many advantages of this approach are its selectiveness in delivering the radiation to the target, relatively less severe and infrequent side effects, and the possibility of assessing the uptake by the tumor prior to the therapy. Several different radiopharmaceuticals are currently being used by various administration routes and targeting mechanisms. This article aims to briefly review the current status of targeted radiotherapy as well as to outline the advantages and disadvantages of radionuclides used for this purpose.

  4. Targeted Radionuclide Therapy

    Energy Technology Data Exchange (ETDEWEB)

    Ersahin, Devrim, E-mail: devrimersahin@yahoo.com; Doddamane, Indukala; Cheng, David [Department of Diagnostic Radiology, School of Medicine, Yale University, 333 Cedar St., New Haven, CT 06520 (United States)

    2011-10-11

    Targeted radiotherapy is an evolving and promising modality of cancer treatment. The killing of cancer cells is achieved with the use of biological vectors and appropriate radionuclides. Among the many advantages of this approach are its selectiveness in delivering the radiation to the target, relatively less severe and infrequent side effects, and the possibility of assessing the uptake by the tumor prior to the therapy. Several different radiopharmaceuticals are currently being used by various administration routes and targeting mechanisms. This article aims to briefly review the current status of targeted radiotherapy as well as to outline the advantages and disadvantages of radionuclides used for this purpose.

  5. Target Assembly Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Target Assembly Facility integrates new armor concepts into actual armored vehicles. Featuring the capability ofmachining and cutting radioactive materials, it...

  6. Targeted Radionuclide Therapy

    International Nuclear Information System (INIS)

    Ersahin, Devrim; Doddamane, Indukala; Cheng, David

    2011-01-01

    Targeted radiotherapy is an evolving and promising modality of cancer treatment. The killing of cancer cells is achieved with the use of biological vectors and appropriate radionuclides. Among the many advantages of this approach are its selectiveness in delivering the radiation to the target, relatively less severe and infrequent side effects, and the possibility of assessing the uptake by the tumor prior to the therapy. Several different radiopharmaceuticals are currently being used by various administration routes and targeting mechanisms. This article aims to briefly review the current status of targeted radiotherapy as well as to outline the advantages and disadvantages of radionuclides used for this purpose

  7. Targeting the tumor microenvironment

    Energy Technology Data Exchange (ETDEWEB)

    Kenny, P.A.; Lee, G.Y.; Bissell, M.J.

    2006-11-07

    Despite some notable successes cancer remains, for the most part, a seemingly intractable problem. There is, however, a growing appreciation that targeting the tumor epithelium in isolation is not sufficient as there is an intricate mutually sustaining synergy between the tumor epithelial cells and their surrounding stroma. As the details of this dialogue emerge, new therapeutic targets have been proposed. The FDA has already approved drugs targeting microenvironmental components such as VEGF and aromatase and many more agents are in the pipeline. In this article, we describe some of the 'druggable' targets and processes within the tumor microenvironment and review the approaches being taken to disrupt these interactions.

  8. Target reactor development problems

    International Nuclear Information System (INIS)

    Lathrop, K.D.; Vigil, J.C.

    1977-01-01

    Target-blanket design studies are discussed for an accelerator-breeder concept employing a linear accelerator in conjunction with a modified conventional power reactor to produce both fissile fuel and power. The following problems in target and blanket system design are discussed: radiation damage, heat removal, neutronic design, and economics

  9. The CNGS target

    CERN Multimedia

    Patrice Loïez

    2005-01-01

    The CERN Neutrinos to Gran Sasso (CNGS) target ‘magazine’ of five target units. Each unit contains a series of 10-cm long graphite rods distributed over a length of 2 m. It is designed to maximize the number of secondary particles produced and hence the number of neutrinos. One unit is used at a time to prevent over heating.

  10. Targeted radionuclide therapy

    African Journals Online (AJOL)

    target for which a speci c treatment/drug is intended (Fig. 1). eranostics .... Using an anti-CD20 antibody as a delivery device to target the follicular ... systems combine diagnostic imaging (Ga-68-DOTATATE PET/CT) .... Intra-articular injected ...

  11. Modelling Recycling Targets

    DEFF Research Database (Denmark)

    hill, amanda; Leinikka Dall, Ole; Andersen, Frits Møller

    2014-01-01

    % for household waste, and sets an ambitious goal of a 50% recycling rate by 2020. This study integrates the recycling target into the FRIDA model to project how much waste and from which streams should be diverted from incineration to recycling in order to achieve the target. Furthermore, it discusses how...

  12. Strategic Targeted Advertising

    NARCIS (Netherlands)

    A. Galeotti; J.L. Moraga-Gonzalez (José Luis)

    2003-01-01

    textabstractWe present a strategic game of pricing and targeted-advertising. Firms can simultaneously target price advertisements to different groups of customers, or to the entire market. Pure strategy equilibria do not exist and thus market segmentation cannot occur surely. Equilibria exhibit

  13. Seedling root targets

    Science.gov (United States)

    Diane L. Haase

    2011-01-01

    Roots are critical to seedling performance after outplanting. Although root quality is not as quick and simple to measure as shoot quality, target root characteristics should be included in any seedling quality assessment program. This paper provides a brief review of root characteristics most commonly targeted for operational seedling production. These are: root mass...

  14. Internal targets for LEAR

    International Nuclear Information System (INIS)

    Kilian, K.; Gspann, J.; Mohl, D.; Poth, H.

    1984-01-01

    This chapter considers the use of thin internal targets in conjunction with phase-space cooling at the Low-Energy Antiproton Ring (LEAR). Topics considered include the merits of internal target operation; the most efficient use of antiprotons and of proton synchrotron (PS) protons, highest center-of-mass (c.m.) energy resolution; highest angular resolution and access to extreme angles; the transparent environment for all reaction products; a windowless source and pure targets; highest luminosity and count rates; access to lowest energies with increasing resolution; internal target thickness and vacuum requirements; required cooling performance; and modes of operation. It is demonstrated that an internal target in conjunction with phase-space cooling has the potential of better performance in terms of the economic use of antiprotons and consequently of PS protons; energy resolution; angular resolution; maximum reaction rate capability (statistical precision); efficient parasitic operation; transparency of the target for reaction products; access to low energies; and the ease of polarized target experiments. It is concluded that all p - experiments which need high statistics and high p - flux, such as studies of rare channels or broad, weak resonance structures, would profit from internal targets

  15. Fusion target design

    International Nuclear Information System (INIS)

    Bangerter, R.O.

    1978-01-01

    Most detailed fusion target design is done by numerical simulation using large computers. Although numerical simulation is briefly discussed, this lecture deals primarily with the way in which basic physical arguments, driver technology considerations and economical power production requirements are used to guide and augment the simulations. Physics topics discussed include target energetics, preheat, stability and symmetry. A specific design example is discussed

  16. Electron beam fusion targets

    International Nuclear Information System (INIS)

    Clauser, M.J.; Sweeney, M.A.

    1975-01-01

    R The behavior of the DT filled gold shells when irradiated by a variety of pulse shapes was studied. In these pulses the power (and beam current) was varied, but the voltage was kept constant at 1 MeV. In general the performance of the target, for a given peak power, was not significantly affected by the pulse shape. Pulses with rise times of up to half the implosion time do not significantly degrade the target performance. The use of the ''optimal pulse'' of laser fusion with a fixed peak power does not appear to improve the performance of these targets. The main function of the ''optimal pulse'' is to produce a large rho r of the target during the thermonuclear burn. In e-beam targets a total rho r of 5--10 g/cm 2 can be obtained without pulse shaping; the problem here is one of achieving high enough temperatures to ignite the DT. (U.S.)

  17. AA antiproton production target

    CERN Multimedia

    CERN PhotoLab

    1979-01-01

    The first version of the antiproton production target was a tungsten rod, 11 cm long and 3 mm in diameter. The rod was embedded in graphite, pressure-seated into an outer casing of stainless steel. At the entrance to the target assembly was a scintillator screen, imprinted with circles every 5 mm in radius, which allowed to precisely aim the 26 GeV high-intensity proton beam from the PS onto the centre of the target rod. The scintillator screen was a 1 mm thick plate of Cr-doped alumina. See also 7903034 and 7905091.

  18. Shiva target irradiation facility

    International Nuclear Information System (INIS)

    Manes, K.R.; Ahlstrom, H.G.; Coleman, L.W.; Storm, E.K.; Glaze, J.A.; Hurley, C.A.; Rienecker, F.; O'Neal, W.C.

    1977-01-01

    The first laser/plasma studies performed with the Shiva laser system will be two sided irradiations extending the data obtained by other LLL lasers to higher powers. The twenty approximately 1 TW laser pulses will reach the target simultaneously from above and below in nested pentagonal clusters. The upper and lower clusters of ten beams each are radially polarized so that they strike the target in p-polarization and maximize absorption. This geometry introduces laser system isolation problems which will be briefly discussed. The layout and types of target diagnostics will be described and a brief status report on the facility given

  19. STANFORD: Internal targets

    Energy Technology Data Exchange (ETDEWEB)

    Riordan, Michael

    1989-05-15

    Of burgeoning interest to many nuclear and particle physicists is a storage ring technique for fixed target experiments. It hinges on the use of gas-jet targets, shooting a narrow stream of atoms through a circulating beam of electrons or protons. Pioneered at CERN and the Soviet Novosibirsk Laboratory, more such 'internal targets' are being built or contemplated for storage rings in Europe, the Soviet Union, and the United States. From 9-12 January, physicists from around the world met at the Stanford Linear Accelerator Center (SLAC) to discuss prospects and problems in this expanding field.

  20. TARGET Research Goals

    Science.gov (United States)

    TARGET researchers use various sequencing and array-based methods to examine the genomes, transcriptomes, and for some diseases epigenomes of select childhood cancers. This “multi-omic” approach generates a comprehensive profile of molecular alterations for each cancer type. Alterations are changes in DNA or RNA, such as rearrangements in chromosome structure or variations in gene expression, respectively. Through computational analyses and assays to validate biological function, TARGET researchers predict which alterations disrupt the function of a gene or pathway and promote cancer growth, progression, and/or survival. Researchers identify candidate therapeutic targets and/or prognostic markers from the cancer-associated alterations.

  1. Structured cylindrical targets

    International Nuclear Information System (INIS)

    Arnold, R.

    1986-01-01

    A variety of experimental concepts using high-energy heavy-ion beams in cylindrical targets have been studied through numerical simulation. With an accelerator planned for GSl, plasma temperatures of 100 eV can be reached by cylindrical compression, using inhomogeneous hollow-shell targets. Magnetic insulation, using external fields, has been explored as an aid in reaching high core temperatures. Experiments on collision-pumped x-ray laser physics are also discussed. (ii) Two-dimensional PlC code simulations of homogeneous solid targets show hydrodynamic effects not found in previous 1-D calculations. (iii) Preliminary ideas for an experiment on non-equilibrium heavy-ion charge-states using an existing accelerator and a pre-formed plasma target are outlined. (author)

  2. Structured cylindrical targets

    International Nuclear Information System (INIS)

    Arnold, R.; Lackner-Russo, D.; Meyer-ter-Vehn, J.; Hoffmann, I.

    1986-01-01

    A variety of experimental concepts using high-energy heavy-ion beams in cylindrical targets have been studied through numerical simulation. With an accelerator planned for GSl, plasma temperatures of 100 eV can be reached by cylindrical compression, using inhomogenous hollow-shell targets. Magnetic insulation, using external fields, has been explored as an aid in reaching high core temperatures. Experiments on collision-pumped x-ray laser physics are also discussed. (ii) Two-dimensional PlC code simulations of homogeneous solid targets show hydrodynamic effects not found in previous l-D calculations. (iii) Preliminary ideas for an experiment on non-equilibrium heavy-ion charge-states using an existing accelerator and a pre-formed plasma target are outlined. (author)

  3. Target Price Accuracy

    Directory of Open Access Journals (Sweden)

    Alexander G. Kerl

    2011-04-01

    Full Text Available This study analyzes the accuracy of forecasted target prices within analysts’ reports. We compute a measure for target price forecast accuracy that evaluates the ability of analysts to exactly forecast the ex-ante (unknown 12-month stock price. Furthermore, we determine factors that explain this accuracy. Target price accuracy is negatively related to analyst-specific optimism and stock-specific risk (measured by volatility and price-to-book ratio. However, target price accuracy is positively related to the level of detail of each report, company size and the reputation of the investment bank. The potential conflicts of interests between an analyst and a covered company do not bias forecast accuracy.

  4. Autonomous Target Ranging Techniques

    DEFF Research Database (Denmark)

    Jørgensen, Peter Siegbjørn; Jørgensen, John Leif; Denver, Troelz

    2003-01-01

    of this telescope, a fast determination of the range to and the motion of the detected targets are important. This is needed in order to prepare the future observation strategy for each target, i.e. when is the closest approach where imaging will be optimal. In order to quickly obtain such a determination two...... ranging strategies are presented. One is an improved laser ranger with an effective range with non-cooperative targets of at least 10,000 km, demonstrated in ground tests. The accuracy of the laser ranging will be approximately 1 m. The laser ranger may furthermore be used for trajectory determination...... of nano-gravity probes, which will perform direct mass measurements of selected targets. The other is triangulation from two spacecraft. For this method it is important to distinguish between detection and tracking range, which will be different for Bering since different instruments are used...

  5. Targeted Cancer Therapies

    Science.gov (United States)

    ... are sometimes referred to as the product of "rational" drug design.) One approach to identify potential targets ... molecules that stimulate new blood vessel growth. Immunotherapies trigger the immune system to destroy cancer cells. Some ...

  6. Targeting radiation to tumours

    International Nuclear Information System (INIS)

    Wheldon, T.E.; Greater Glasgow Health Board, Glasgow

    1994-01-01

    Biologically targeted radiotherapy entails the preferential delivery of radiation to solid tumours or individual tumour cells by means of tumour-seeking delivery vehicles to which radionuclides can be conjugated. Monoclonal antibodies have attracted attention for some years as potentially selective targeting agents, but advances in tumour and molecular biology are now providing a much wider choice of molecular species. General radiobiological principles may be derived which are applicable to most forms of targeted radiotherapy. These principles provide guidelines for the appropriate choice of radionuclide in specific treatment situations and its optimal combination with other treatment modalities. In future, the availability of gene targeting agents will focus attention on the use of Auger electron emitters whose high potency and short range selectivity makes them attractive choices for specific killing of cancer cells whose genetic peculiarities are known. (author)

  7. Strategic Targeted Advertising

    OpenAIRE

    Andrea Galeotti; Jose Luis Moraga

    2003-01-01

    textabstractWe present a strategic game of pricing and targeted-advertising. Firms can simultaneously target price advertisements to different groups of customers, or to the entire market. Pure strategy equilibria do not exist and thus market segmentation cannot occur surely. Equilibria exhibit random advertising --to induce an unequal distribution of information in the market-- and random pricing --to obtain profits from badly informed buyers--. We characterize a positive profits equilibrium...

  8. Targets and teamwork

    DEFF Research Database (Denmark)

    Skinner, Timothy C.; Lange, Karin S.; Hoey, Hilary

    2017-01-01

    differences in mean HbA1c between centers ranging from 7.3±0.8% (53mmol/mol±8.7) to 8.9±1.1% (74mmol/mol±12.0). Centers with lower mean HbA1c had (1) parents who reported lower targets for their children, (2) health-care professionals that reported lower targets and more frequent testing, and (3) teams...

  9. Targets and special materials

    International Nuclear Information System (INIS)

    Blanc, R.; Bouriant, M.; Richaud, J.P.

    1997-01-01

    The target preparation group supplied a large number of samples to nuclear physicists for experiments using SARA and also other accelerators throughout the world. Particular preparation and projects include: 208 Pb, 116 Cd, 6 LiF, 123 Sb, In and Ta targets, strippers for SARA and GANIL, optical silicone disks for POLDER and GRAAL experiments, active participations for the AMS project and finally filament preparation for the GENEPI project. (authors)

  10. The ISIS target

    International Nuclear Information System (INIS)

    Carne, A.; Broome, T.A.; Hogston, J.R.; Holding, M.

    1989-01-01

    This presentation discusses the two target failures that have occurred, gives the understanding of the causes and indicates the steps being taken to alleviate the problems. At the outset of the design it was understood that the target would have a finite lifetime, due to radiation damage effects, exacerbated by mechanical damage due to thermal cycling and fatigue. Estimates of target lifetime at full intensity are about 2 years for radiation damage swelling and about 10E4 gross thermal excursions. The latter number is the one which gives uncertainty in defining the life of the target, since it is dependent on the reliability of the accelerator and quality of the proton beam. The commissioning of an accelerator system and bringing it up to high beam intensities have their own special problems. There must be protection of components against uncontrolled beam loss, which produces thermal damage, prompt radiation and induced activity. Fast beam trips for beam loss protection, or equipment failures, result in quenches from high temperature in the target which get bigger with increasing beam intensity. But the target itself is a difficult device to make, taking about 12 months to manufacture. Further, changing one is a complex and time consuming task, not without its hazards. There is thus something of a balancing act to bring the accelerator towards specification before the target fails due to thermal cycling fatigue. In the early days of ISIS beam loss protection was the dominant consideration and the target was regarded somewhat as a sacrificial lamb to the goddess of machine reliability. 2 refs., 6 figs

  11. An ISOLDE target unit

    CERN Multimedia

    Maximilien Brice

    2002-01-01

    A good dozen different targets are available for ISOLDE, made of different materials and equipped with different kinds of ion-sources, according to the needs of the experiments. Each separator (GPS: general purpose; HRS: high resolution) has its own target. Because of the high radiation levels, robots effect the target changes, about 80 times per year. In the standard unit shown in picture _01, the target is the cylindrical object in the front. It contains uranium-carbide kept at a temperature of 2200 deg C, necessary for the isotopes to be able to escape. At either end, one sees the heater current leads, carrying 700 A. The Booster beam, some 3E13 protons per pulse, enters the target from left. The evaporated isotope atoms enter a hot-plasma ion source (the black object behind the target). The whole unit sits at 60 kV potential (pulsed in synchronism with the arrival of the Booster beam) which accelerates the ions (away from the viewer) towards one of the 2 separators.

  12. Laser targets: introduction

    International Nuclear Information System (INIS)

    Rosen, M.D.

    1985-01-01

    The laser target design group was engaged in three main tasks in 1984: (1) analyzing Novette implosion and hohlraum-scaling data, (2) planning for the first experiments on Nova, and (3) designing laboratory x-ray laser targets and experiments. The Novette implosion and hohlraum scaling data are mostly classified and are therefore not discussed in detail here. The authors achieved average final/initial pusher pr ratios of about 50, some 3 times higher than the value achieved in the best Shiva shots. These pr values imply a fuel compression to 100 times liquid density, although this figure and other aspects of the experiments are subject to further interpretation because of detailed questions of target symmetry and stability. Their main long-term goal for Nova is to produce a so-called hydrodynamically equivalent target (HET) - that is, a target whose hydrodynamic behavior (implosion velocity, convergence ratio, symmetry and stability requirements, etc.) is very much like that of a high-gain target, but one that is scaled down in size to match the energy available from Nova and is too small to achieve enough hot-spot pr to ignite the cold, near-Fermi-degenerate fuel around it. Their goal for Nova's first year is to do experiments that will teach them how to achieve the symmetry and stability conditions required by an HET

  13. Argus target chamber

    International Nuclear Information System (INIS)

    Rienecker, F. Jr.; Glaros, S.S.; Kobierecki, M.

    1975-01-01

    A target chamber for application in the laser fusion program must satisfy some very basic requirements. (1) Provide a vacuum on the order of 10 -6 torr. (2) Support a microscopically small target in a fixed point in space and verify its location within 5 micrometers. (3) Contain an adjustable beam focusing system capable of delivering a number of laser beams onto the target simultaneously, both in time and space. (4) Provide access for diagnostics to evaluate the results of target irradiation. (5) Have flexibility to allow changes in targets, focusing optics and number of beams. The ARGUS laser which is now under construction at LLL will have a target chamber which meets these requirements in a simple economic manner. The chamber and auxiliary equipment are described, with reference to two double beam focusing systems; namely, lenses and ellipsoidal mirrors. Provision is made for future operation with four beams, using ellipsoidal mirrors for two-sided illumination and lens systems for tetragonal and tetrahedral irradiation

  14. Burglar Target Selection

    Science.gov (United States)

    Townsley, Michael; Bernasco, Wim; Ruiter, Stijn; Johnson, Shane D.; White, Gentry; Baum, Scott

    2015-01-01

    Objectives: This study builds on research undertaken by Bernasco and Nieuwbeerta and explores the generalizability of a theoretically derived offender target selection model in three cross-national study regions. Methods: Taking a discrete spatial choice approach, we estimate the impact of both environment- and offender-level factors on residential burglary placement in the Netherlands, the United Kingdom, and Australia. Combining cleared burglary data from all study regions in a single statistical model, we make statistical comparisons between environments. Results: In all three study regions, the likelihood an offender selects an area for burglary is positively influenced by proximity to their home, the proportion of easily accessible targets, and the total number of targets available. Furthermore, in two of the three study regions, juvenile offenders under the legal driving age are significantly more influenced by target proximity than adult offenders. Post hoc tests indicate the magnitudes of these impacts vary significantly between study regions. Conclusions: While burglary target selection strategies are consistent with opportunity-based explanations of offending, the impact of environmental context is significant. As such, the approach undertaken in combining observations from multiple study regions may aid criminology scholars in assessing the generalizability of observed findings across multiple environments. PMID:25866418

  15. LANSCE target system performance

    International Nuclear Information System (INIS)

    Russell, G.J.; Gilmore, J.S.; Robinson, H.; Legate, G.L.; Bridge, A.; Sanchez, R.J.; Brewton, R.J.; Woods, R.; Hughes, H.G. III

    1989-01-01

    We measured neutron beam fluxes at LANSCE using gold foil activation techniques. We did an extensive computer simulation of the as-built LANSCE Target/Moderator/Reflector/Shield geometry. We used this mockup in a Monte Carlo calculation to predict LANSCE neutronic performance for comparison with measured results. For neutron beam fluxes at 1 eV, the ratio of measured data to calculated varies from ∼0.6-0.9. The computed 1 eV neutron leakage at the moderator surface is 3.9 x 10 10 n/eV-sr-s-μA for LANSCE high-intensity water moderators. The corresponding values for the LANSCE high-resolution water moderator and the liquid hydrogen moderator are 3.3 and 2.9 x 10 10 , respectively. LANSCE predicted moderator intensities (per proton) for a tungsten target are essentially the same as ISIS predicted moderator intensities for a depleted uranium target. The calculated LANSCE steady state unperturbed thermal (E 13 n/cm 2 -s. The unique LANSCE split-target/flux-trap-moderator system is performing exceedingly well. The system has operated without a target or moderator change for over three years at nominal proton currents of ∼25 μA of 800-MeV protons. (author)

  16. Modelling Recycling Targets

    DEFF Research Database (Denmark)

    Hill, Amanda Louise; Leinikka Dall, Ole; Andersen, Frits M.

    2014-01-01

    Within the European Union (EU) a paradigm shift is currently occurring in the waste sector, where EU waste directives and national waste strategies are placing emphasis on resource efficiency and recycling targets. The most recent Danish resource strategy calculates a national recycling rate of 22......% for household waste, and sets an ambitious goal of a 50% recycling rate by 2020. This study integrates the recycling target into the FRIDA model to project how much waste and from which streams should be diverted from incineration to recycling in order to achieve the target. Furthermore, it discusses how...... the existing technological, organizational and legislative frameworks may affect recycling activities. The results of the analysis show that with current best practice recycling rates, the 50% recycling rate cannot be reached without recycling of household biowaste. It also shows that all Danish municipalities...

  17. Targeted Phototherapy (newer phototherapy

    Directory of Open Access Journals (Sweden)

    Zonunsanga

    2015-04-01

    Full Text Available Conventional phototherapy uses a whole body cabinet or body part machine such as hand, foot or scalp machines. They have many disadvantages due to which new phototherapy technique was then developed to overcome this situation. This new technique is called targeted phototherapy which includes excimer laser, intense pulse light system (IPL, photodynamic therapy and ultraviolet (UV light source with a sophisticated delivery system which is easy to be operated by hands. The mechanisms of action of targeted phototherapy systems are similar to those in conventional UVB/UVA therapy. They have many advantages like less chances of side effects, avoidance of exposure of unnecessary sites, faster response, shortening of the duration of treatments. But they have disadvantages like high costs and inability to use for extensive areas. This review article discusses targeted phototherapy in considerable to the mechanism of actions and advantages and disadvantages in comparison to the conventional phototherapy.

  18. Setting reference targets

    International Nuclear Information System (INIS)

    Ruland, R.E.

    1997-04-01

    Reference Targets are used to represent virtual quantities like the magnetic axis of a magnet or the definition of a coordinate system. To explain the function of reference targets in the sequence of the alignment process, this paper will first briefly discuss the geometry of the trajectory design space and of the surveying space, then continue with an overview of a typical alignment process. This is followed by a discussion on magnet fiducialization. While the magnetic measurement methods to determine the magnetic centerline are only listed (they will be discussed in detail in a subsequent talk), emphasis is given to the optical/mechanical methods and to the task of transferring the centerline position to reference targets

  19. Effects of MAR-M247 substrate (modified) composition on coating oxidation coating/substrate interdiffusion. M.S. Thesis. Final Report; [protective coatings for hot section components of gas turbine engines

    Science.gov (United States)

    Pilsner, B. H.

    1985-01-01

    The effects of gamma+gamma' Mar-M247 substrate composition on gamma+beta Ni-Cr-Al-Zr coating oxidation and coating/substrate interdiffusion were evaluated. These results were also compared to a prior study for a Ni-Cr-Al-Zr coated gamma Ni-Cr-Al substrate with equivalent Al and Cr atomic percentages. Cyclic oxidation behavior at 1130 C was investigated using change in weight curves. Concentration/distance profiles were measured for Al, Cr, Co, W, and Ta. The surface oxides were examined by X-ray diffraction and scanning electron microscopy. The results indicate that variations of Ta and C concentrations in the substrate do not affect oxidation resistance, while additions of grain boundary strengthening elements (Zr, Hf, B) increase oxidation resistance. In addition, the results indicate that oxidation phenomena in gamma+beta/gamma+gamma' Mar-M247 systems have similar characteristics to the l gamma+beta/gamma Ni-Cr-Al system.

  20. Fine target of deuterium

    International Nuclear Information System (INIS)

    Diaz Diaz, J.; Granados Gonzalez, C. E.; Gutierrez Bernal, R.

    1959-01-01

    A fine target of deuterium on a tantalum plate by the absorption method is obtained. In order to obtain the de gasification temperature an induction generator of high frequency is used and the deuterium pass is regulated by means of a palladium valve. Two vacuum measures are available, one to measure the high vacuum in the de gasification process of the tantalum plate and the other, for low vacuum, to measure the deuterium inlet in the installation and the deuterium pressure change in the installation after the absorption in the tantalum plate. A target of 48 μ gr/cm 2 thick is obtained. (Author) 1 refs

  1. Targeting the right journal.

    Science.gov (United States)

    Piterman, L; McCall, L

    1999-07-01

    While research is scientific, publication is a mixture of science and political pragmatism. Targeting the right journal is influenced by the following factors: the discipline that best represents the subject; the purpose of the message; the audience who are to be recipients of the message; the realities of geographic parochialism; the desire of authors to maximise personal and professional opportunities. If the originally targeted journal rejects the article, authors should have alternative publication strategies that give them professional recognition without requiring them to compromise the message or their ethics.

  2. AA antiproton production target

    CERN Multimedia

    CERN PhotoLab

    1979-01-01

    The first version of the antiproton production target was a tungsten rod, 11 cm long (actually a row of 11 rods, each 1 cm long) and 3 mm in diameter. The rod was embedded in graphite, pressure-seated into an outer casing made of stainless steel. The casing had fins for forced-air cooling. In this picture, the 26 GeV high-intensity beam from the PS enters from the right, where a scintillator screen, with circles every 5 mm in radius, permits precise aim at the target centre. See also 7903034 and 7905094.

  3. Targets and tactics

    DEFF Research Database (Denmark)

    Woo, V; Shestakova, M V; Ørskov, C

    2008-01-01

    BACKGROUND: The incidence of type 2 diabetes is reaching pandemic proportions, impacting patients and healthcare systems across the globe. Evidence suggests that a majority of patients are not achieving recommended blood glucose targets resulting in an increased risk of micro- and macro-vascular ......BACKGROUND: The incidence of type 2 diabetes is reaching pandemic proportions, impacting patients and healthcare systems across the globe. Evidence suggests that a majority of patients are not achieving recommended blood glucose targets resulting in an increased risk of micro- and macro...... diabetes has never been more compelling; with a clear focus on strategies for glycaemic control, the impact of the diabetes pandemic can be limited....

  4. Optimal exploration target zones

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2008-09-01

    Full Text Available -of-evidence (WofE) method logistic regression canonical favorability analysis neural networks evidential belief functions Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote Sensing Background and Objective of the study... for the following equation: n∑ i=r ( n i ) pi(1− p)n−i = 0.95 . (1) Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote Sensing Background and Objective of the study Methodology Results METHODS (cont. . . ): FITNESS FUNCTION...

  5. ISOLDE back on target

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    Today, Friday 1 August, the ISOLDE installation, supplied by the beams of the PS Booster, restarted its physics programme. After a shutdown of almost a year and a half, there was a real buzz in the air as the first beam of protons hit the target of the first post-LS1 ISOLDE experiment.   One of the new target-handling robots installed by ISOLDE during LS1. Many improvements have been made to the ISOLDE installation during LS1. One of the main projects was the installation of new robots for handling the targets (see photo 1). “Our targets are bombarded by protons from the PS Booster’s beams and become very radioactive,” explains Maria Jose Garcia Borge, spokesperson for the ISOLDE collaboration. “They therefore need to be handled carefully, which is where the robots come in. The robots we had until now were already over 20 years old and were starting to suffer from the effects of radiation. So LS1 was a perfect opportunity to replace them with more moder...

  6. Targeted Therapy for Melanoma

    International Nuclear Information System (INIS)

    Quinn, Thomas; Moore, Herbert

    2016-01-01

    The research project, entitled ''Targeted Therapy for Melanoma,'' was focused on investigating the use of kidney protection measures to lower the non-specific kidney uptake of the radiolabeled Pb-DOTA-ReCCMSH peptide. Previous published work demonstrated that the kidney exhibited the highest non-target tissue uptake of the "2"1"2"P"b"/"2"0"3Pb radiolabeled melanoma targeting peptide DOTA-ReCCMSH. The radiolabeled alpha-melanocyte stimulating hormone (α-MSH) peptide analog DOTA-Re(Arg"1"1)CCMSH, which binds the melanocortin-1 receptor over-expressed on melanoma tumor cells, has shown promise as a PRRT agent in pre-clinical studies. High tumor uptake of "2"1"2Pb labeled DOTA-Re(Arg"1"1)CCMSH resulted in tumor reduction or eradication in melanoma therapy studies. Of particular note was the 20-50% cure rate observed when melanoma mice were treated with alpha particle emitter "2"1"2Pb. However, as with most PRRT agents, high radiation doses to the kidneys where observed. To optimize tumor treatment efficacy and reduce nephrotoxicity, the tumor to kidney uptake ratio must be improved. Strategies to reduce kidney retention of the radiolabeled peptide, while not effecting tumor uptake and retention, can be broken into several categories including modification of the targeting peptide sequence and reducing proximal tubule reabsorption.

  7. Targets of curcumin

    Science.gov (United States)

    Zhou, Hongyu; Beevers, Christopher S.; Huang, Shile

    2010-01-01

    Curcumin (diferuloylmethane), an orange-yellow component of turmeric or curry powder, is a polyphenol natural product isolated from the rhizome of the plant Curcuma longa. For centuries, curcumin has been used in some medicinal preparation or used as a food-coloring agent. In recent years, extensive in vitro and in vivo studies suggested curcumin has anticancer, antiviral, antiarthritic, anti-amyloid, antioxidant, and anti-inflammatory properties. The underlying mechanisms of these effects are diverse and appear to involve the regulation of various molecular targets, including transcription factors (such as nuclear factor-κB), growth factors (such as vascular endothelial cell growth factor), inflammatory cytokines (such as tumor necrosis factor, interleukin 1 and interleukin 6), protein kinases (such as mammalian target of rapamycin, mitogen-activated protein kinases, and Akt) and other enzymes (such as cyclooxygenase 2 and 5 lipoxygenase). Thus, due to its efficacy and regulation of multiple targets, as well as its safety for human use, curcumin has received considerable interest as a potential therapeutic agent for the prevention and/or treatment of various malignant diseases, arthritis, allergies, Alzheimer’s disease, and other inflammatory illnesses. This review summarizes various in vitro and in vivo pharmacological aspects of curcumin as well as the underlying action mechanisms. The recently identified molecular targets and signaling pathways modulated by curcumin are also discussed here. PMID:20955148

  8. Target-Rich Environment

    Science.gov (United States)

    Perna, Mark C.

    2005-01-01

    Target marketing is defining school enrollment goals and then developing a strategic plan to accomplish those goals through the use of specific communication vehicles and community focus. It is critical to reach the right audience, with the right message, at the right time, for the right cost. In this brief article, the author describes several…

  9. Targeted enzyme prodrug therapies.

    Science.gov (United States)

    Schellmann, N; Deckert, P M; Bachran, D; Fuchs, H; Bachran, C

    2010-09-01

    The cure of cancer is still a formidable challenge in medical science. Long-known modalities including surgery, chemotherapy and radiotherapy are successful in a number of cases; however, invasive, metastasized and inaccessible tumors still pose an unresolved and ongoing problem. Targeted therapies designed to locate, detect and specifically kill tumor cells have been developed in the past three decades as an alternative to treat troublesome cancers. Most of these therapies are either based on antibody-dependent cellular cytotoxicity, targeted delivery of cytotoxic drugs or tumor site-specific activation of prodrugs. The latter is a two-step procedure. In the first step, a selected enzyme is accumulated in the tumor by guiding the enzyme or its gene to the neoplastic cells. In the second step, a harmless prodrug is applied and specifically converted by this enzyme into a cytotoxic drug only at the tumor site. A number of targeting systems, enzymes and prodrugs were investigated and improved since the concept was first envisioned in 1974. This review presents a concise overview on the history and latest developments in targeted therapies for cancer treatment. We cover the relevant technologies such as antibody-directed enzyme prodrug therapy (ADEPT), gene-directed enzyme prodrug therapy (GDEPT) as well as related therapies such as clostridial- (CDEPT) and polymer-directed enzyme prodrug therapy (PDEPT) with emphasis on prodrug-converting enzymes, prodrugs and drugs.

  10. Targeting trichothecene biosynthetic genes

    NARCIS (Netherlands)

    Wei, Songhong; Lee, van der Theo; Verstappen, Els; Gent, van Marga; Waalwijk, Cees

    2017-01-01

    Biosynthesis of trichothecenes requires the involvement of at least 15 genes, most of which have been targeted for PCR. Qualitative PCRs are used to assign chemotypes to individual isolates, e.g., the capacity to produce type A and/or type B trichothecenes. Many regions in the core cluster

  11. Targeted Therapy for Melanoma

    Energy Technology Data Exchange (ETDEWEB)

    Quinn, Thomas [Alphamed, Jackson, TN (United States); Moore, Herbert [Alphamed, Jackson, TN (United States)

    2016-12-05

    The research project, entitled ”Targeted Therapy for Melanoma,” was focused on investigating the use of kidney protection measures to lower the non-specific kidney uptake of the radiolabeled Pb-DOTA-ReCCMSH peptide. Previous published work demonstrated that the kidney exhibited the highest non-target tissue uptake of the 212Pb/203Pb radiolabeled melanoma targeting peptide DOTA-ReCCMSH. The radiolabeled alpha-melanocyte stimulating hormone (α-MSH) peptide analog DOTA-Re(Arg11)CCMSH, which binds the melanocortin-1 receptor over-expressed on melanoma tumor cells, has shown promise as a PRRT agent in pre-clinical studies. High tumor uptake of 212Pb labeled DOTA-Re(Arg11)CCMSH resulted in tumor reduction or eradication in melanoma therapy studies. Of particular note was the 20-50% cure rate observed when melanoma mice were treated with alpha particle emitter 212Pb. However, as with most PRRT agents, high radiation doses to the kidneys where observed. To optimize tumor treatment efficacy and reduce nephrotoxicity, the tumor to kidney uptake ratio must be improved. Strategies to reduce kidney retention of the radiolabeled peptide, while not effecting tumor uptake and retention, can be broken into several categories including modification of the targeting peptide sequence and reducing proximal tubule reabsorption.

  12. The targets of curcumin.

    Science.gov (United States)

    Zhou, Hongyu; Beevers, Christopher S; Huang, Shile

    2011-03-01

    Curcumin (diferuloylmethane), an orange-yellow component of turmeric or curry powder, is a polyphenol natural product isolated from the rhizome of the plant Curcuma longa. For centuries, curcumin has been used in some medicinal preparation or used as a food-coloring agent. In recent years, extensive in vitro and in vivo studies suggested curcumin has anticancer, antiviral, antiarthritic, anti-amyloid, antioxidant, and anti-inflammatory properties. The underlying mechanisms of these effects are diverse and appear to involve the regulation of various molecular targets, including transcription factors (such as nuclear factor-kB), growth factors (such as vascular endothelial cell growth factor), inflammatory cytokines (such as tumor necrosis factor, interleukin 1 and interleukin 6), protein kinases (such as mammalian target of rapamycin, mitogen-activated protein kinases, and Akt) and other enzymes (such as cyclooxygenase 2 and 5 lipoxygenase). Thus, due to its efficacy and regulation of multiple targets, as well as its safety for human use, curcumin has received considerable interest as a potential therapeutic agent for the prevention and/or treatment of various malignant diseases, arthritis, allergies, Alzheimer's disease, and other inflammatory illnesses. This review summarizes various in vitro and in vivo pharmacological aspects of curcumin as well as the underlying action mechanisms. The recently identified molecular targets and signaling pathways modulated by curcumin are also discussed here.

  13. Aberrant status and clinicopathologic characteristic associations of 11 target genes in 1,321 Chinese patients with lung adenocarcinoma.

    Science.gov (United States)

    Zhao, Mengnan; Zhan, Cheng; Li, Ming; Yang, Xiaodong; Yang, Xinyu; Zhang, Yong; Lin, Miao; Xia, Yifeng; Feng, Mingxiang; Wang, Qun

    2018-01-01

    The aberrant status of target genes and their associations with clinicopathologic characteristics are still unclear in primary lung adenocarcinoma. The common mutations and translocations of nine target genes were evaluated in 1,247 specimens of surgically-resected primary lung adenocarcinoma. Immunohistochemistry was used to analyze the expressions of programmed death-1 (PD-1)/programmed death-ligand 1 (PD-L1) in 731 specimens. The frequency of the aberrations and their associations with clinicopathologic characteristics were analyzed. Overall, 952 (76.3%) of 1,247 patients harbored at least one target mutation or translocation: epidermal growth factor receptor ( EGFR ) (729, 58.5%), v-Ki-ras2 Kirsten rat sarcoma viral oncogene homolog ( KRAS ) (83, 6.7%), human epidermal growth factor receptor 2 ( HER2 ) (82, 6.6%), anaplastic lymphoma kinase ( ALK) (23, 1.8%), phosphoinositide-3-kinase catalytic alpha polypeptide ( PIK3CA ) (20, 1.6%), Ret proto-oncogene RET (15, 1.2%), ROS proto-oncogene 1 receptor tyrosine kinase ( ROS1 ) (12, 1.0%), B-raf proto-oncogene ( BRAF ) (9, 0.7%), neuroblastoma RAS viral (v-ras) oncogene homolog ( NRAS ) (3, 0.2%). Fourteen (1.9%) of 731 patients were PD-1 positive and 95 (13.0%) were PD-L1 positive in tumor cells. In men and smokers, there were more frequent KRAS mutations (both Ppatients, while HER2 (Ppatients with EGFR mutations (all Ppatients with primary lung adenocarcinoma harbored target gene aberrations. The frequency of each alteration differed in patients depending on clinicopathologic characteristics.

  14. Parameter measurement of target

    International Nuclear Information System (INIS)

    Gao Dangzhong

    2001-01-01

    The progress of parameter measurement of target (ICF-15) in 1999 are presented, including the design and contract of the microsphere equator profiler, the precise air bearing manufacturing, high-resolution X-ray image of multi-layer shells and the X-ray photos processed with special image and data software, some plastic shells measured in precision of 0.3 μm, the high-resolution observation and photograph system of 'dew-point method', special fixture of target and its temperature distribution measuring, the dew-point temperature and fuel gas pressure of shells measuring with internal pressure of 5 - 15 (x10 5 ) Pa D 2 and wall thickness of 1.5∼3 μm

  15. Guilty Feelings, Targeted Actions

    Science.gov (United States)

    Cryder, Cynthia E.; Springer, Stephen; Morewedge, Carey K.

    2014-01-01

    Early investigations of guilt cast it as an emotion that prompts broad reparative behaviors that help guilty individuals feel better about themselves or about their transgressions. The current investigation found support for a more recent representation of guilt as an emotion designed to identify and correct specific social offenses. Across five experiments, guilt influenced behavior in a targeted and strategic way. Guilt prompted participants to share resources more generously with others, but only did so when those others were persons whom the participant had wronged and only when those wronged individuals could notice the gesture. Rather than trigger broad reparative behaviors that remediate one’s general reputation or self-perception, guilt triggers targeted behaviors intended to remediate specific social transgressions. PMID:22337764

  16. Inertial confinement fusion target

    International Nuclear Information System (INIS)

    Bourdier, A.

    2001-12-01

    A simple, zero-dimensional model describing the temporal behaviour of an imploding-shell, magnetized fuel inertial confinement fusion target is formulated. The addition of a magnetic field to the fuel reduces thermal conduction losses. As a consequence, it might lead to high gains and reduce the driver requirements. This beneficial effect of the magnetic field on thermonuclear gains is confirmed qualitatively by the zero-dimensional model results. Still, the extent of the initial-condition space for which significant gains can occur is not, by far, as large as previously reported. One-dimensional CEA code simulations which confirm this results are also presented. Finally, we suggest to study the approach proposed by Hasegawa. In this scheme, the laser target is not imploded, and the life-time of the plasma can be very much increased. (author)

  17. Hohlraum targets for HIDIF

    International Nuclear Information System (INIS)

    Ramis, R.; Ramirez, J.; Meyer-ter-Vehn, J.

    2000-01-01

    An optimized high gain IFE indirect target design is presented. Beam parameters (5 MJ of 5 GeV Bi + ions in 10-20 ns and focal spot of 3 mm radius) are in agreement to the ones considered recently for the European Study Group on Heavy Ion Driven Inertial Fusion (HIDIF). The energy yield is close to 530 MJ, giving a large enough gain appropriate for industrial energy production. Numerical and analytical modeling are described and discussed. (authors)

  18. Target Glint Suppression Technology.

    Science.gov (United States)

    1980-09-01

    Rayleigh for either horizontal or vertical polarization). 2.1.2 Spatial Characterization. Before the effects of diversity on target detection can be...ncs) dRCS T If the lower intergration limit is taken as zero for the Rayleigh targct model of interest, then this quantity is unbounded. In...port wing, inner section Trailing edge of starboard .:ing, inner section Leading edge of horizontal stabilizer, inner section, port side TLeal, -g

  19. Conditional targeting for communication

    International Nuclear Information System (INIS)

    Rodrigues, Anselmo; Caldas, Ibere L.; Baptista, Murilo S.; Piqueira, Jose Roberto C.

    2004-01-01

    In this work we propose the use of a targeting method applied to chaotic systems in order to reach special trajectories that encode arbitrary sources of messages. One advantage of this procedure is to overcome dynamical constraints which impose limits in the amount of information that the chaotic trajectories can encode. Another advantage is the message decoding, practically instantaneous and independent of any special technique or algorithm. Furthermore, with this procedure, information can be transmitted with no errors due to bounded noise

  20. Heterogeneous chromatin target model

    International Nuclear Information System (INIS)

    Watanabe, Makoto

    1996-01-01

    The higher order structure of the entangled chromatin fibers in a chromosome plays a key role in molecular control mechanism involved in chromosome mutation due to ionizing radiations or chemical mutagens. The condensed superstructure of chromatin is not so rigid and regular as has been postulated in general. We have proposed a rheological explanation for the flexible network system ('chromatin network') that consists of the fluctuating assembly of nucleosome clusters linked with supertwisting DNA in a chromatin fiber ('Supertwisting Particulate Model'). We have proposed a 'Heterosensitive Target Model' for cellular radiosensitivity that is a modification of 'Heterogeneous Target Model'. The heterogeneity of chromatin target is derived from the highly condensed organization of chromatin segments consist of unstable and fragile sites in the fluctuating assembly of nucleosome clusters, namely 'supranucleosomal particles' or 'superbeads'. The models have been principally supported by our electron microscopic experiments employing 'surface - spreading whole - mount technique' since 1967. However, some deformation and artifacts in the chromatin structure are inevitable with these electron microscopic procedures. On the contrary, the 'atomic force microscope (AFM)' can be operated in liquid as well as in the air. A living specimen can be examined without any preparative procedures. Micromanipulation of the isolated chromosome is also possible by the precise positional control of a cantilever on the nanometer scale. The living human chromosomes were submerged in a solution of culture medium and observed by AFM using a liquid immersion cell. The surface - spreading whole - mount technique was applicable for this observation. The particulate chromatin segments of nucleosome clusters were clearly observed within mitotic human chromosomes in a living hydrated condition. These findings support the heterogeneity of chromatin target in a living cell. (J.P.N.)

  1. Implementing Target Value Design.

    Science.gov (United States)

    Alves, Thais da C L; Lichtig, Will; Rybkowski, Zofia K

    2017-04-01

    An alternative to the traditional way of designing projects is the process of target value design (TVD), which takes different departure points to start the design process. The TVD process starts with the client defining an allowable cost that needs to be met by the design and construction teams. An expected cost in the TVD process is defined through multiple interactions between multiple stakeholders who define wishes and others who define ways of achieving these wishes. Finally, a target cost is defined based on the expected profit the design and construction teams are expecting to make. TVD follows a series of continuous improvement efforts aimed at reaching the desired goals for the project and its associated target value cost. The process takes advantage of rapid cycles of suggestions, analyses, and implementation that starts with the definition of value for the client. In the traditional design process, the goal is to identify user preferences and find solutions that meet the needs of the client's expressed preferences. In the lean design process, the goal is to educate users about their values and advocate for a better facility over the long run; this way owners can help contractors and designers to identify better solutions. This article aims to inform the healthcare community about tools and techniques commonly used during the TVD process and how they can be used to educate and support project participants in developing better solutions to meet their needs now as well as in the future.

  2. The Bochum Polarized Target

    International Nuclear Information System (INIS)

    Reicherz, G.; Goertz, S.; Harmsen, J.; Heckmann, J.; Meier, A.; Meyer, W.; Radtke, E.

    2001-01-01

    The Bochum 'Polarized Target' group develops the target material 6 LiD for the COMPASS experiment at CERN. Several different materials like alcohols, alcanes and ammonia are under investigation. Solid State Targets are polarized in magnetic fields higher than B=2.5T and at temperatures below T=1K. For the Dynamic Nuclear Polarization process, paramagnetic centers are induced chemically or by irradiation with ionizing beams. The radical density is a critical factor for optimization of polarization and relaxation times at adequate magnetic fields and temperatures. In a high sensitive EPR--apparatus, an evaporator and a dilution cryostat with a continuous wave NMR--system, the materials are investigated and optimized. To improve the polarization measurement, the Liverpool NMR-box is modified by exchanging the fixed capacitor for a varicap diode which not only makes the tuning very easy but also provides a continuously tuned circuit. The dependence of the signal area upon the circuit current is measured and it is shown that it follows a linear function

  3. Inflation targeting and core inflation

    OpenAIRE

    Julie Smith

    2005-01-01

    This paper examines the interaction of core inflation and inflation targeting as a monetary policy regime. Interest in core inflation has grown because of inflation targeting. Core inflation is defined in numerous ways giving rise to many potential measures; this paper defines core inflation as the best forecaster of inflation. A cross-country study finds before the start of inflation targeting, but not after, core inflation differs between non-inflation targeters and inflation targeters. Thr...

  4. Targeted therapy for sarcomas

    Directory of Open Access Journals (Sweden)

    Forscher C

    2014-03-01

    Full Text Available Charles Forscher,1 Monica Mita,2 Robert Figlin3 1Sarcoma Program, Samuel Oschin Comprehensive Cancer Institute, Cedars-Sinai Medical Center, Los Angeles, CA, USA; 2Experimental Therapeutics Program, Samuel Oschin Comprehensive Cancer Institute, Cedars-Sinai Medical Center, Los Angeles, CA, USA; 3Academic Development Program, Samuel Oschin Comprehensive Cancer Institute, and Division of Hematology/Oncology, Cedars-Sinai Medical Center, Los Angeles, CA, USA Abstract: Sarcomas are tumors of mesenchymal origin that make up approximately 1% of human cancers. They may arise as primary tumors in either bone or soft tissue, with approximately 11,280 soft tissue tumors and 2,650 bone tumors diagnosed each year in the United States. There are at least 50 different subtypes of soft tissue sarcoma, with new ones described with ever-increasing frequency. One way to look at sarcomas is to divide them into categories on the basis of their genetic make-up. One group of sarcomas has an identifiable, relatively simple genetic signature, such as the X:18 translocation seen in synovial sarcoma or the 11:22 translocation seen in Ewing's sarcoma. These specific abnormalities often lead to the presence of fusion proteins, such as EWS-FLI1 in Ewing's sarcoma, which are helpful as diagnostic tools and may become therapeutic targets in the future. Another group of sarcomas is characterized by complex genetic abnormalities as seen in leiomyosarcoma, osteosarcoma, and undifferentiated sarcoma. It is important to keep these distinctions in mind when contemplating the development of targeted agents for sarcomas. Different abnormalities in sarcoma could be divided by tumor subtype or by the molecular or pathway abnormality. However, some existing drugs or drugs in development may interfere with or alter more than one of the presented pathways. Keywords: sarcoma, targeted agents, tyrosine kinase inhibitors, mTor inhibition

  5. Targeted mass spectrometry

    DEFF Research Database (Denmark)

    Osinalde, Nerea; Aloria, Kerman; Omaetxebarria, Miren J.

    2017-01-01

    Following the rapid expansion of the proteomics field, the investigation of post translational modifications (PTM) has become extremely popular changing our perspective of how proteins constantly fine tune cellular functions. Reversible protein phosphorylation plays a pivotal role in virtually all...... for becoming the method of choice to study with high precision and sensitivity already known site-specific phosphorylation events. This review summarizes the contribution of large-scale unbiased MS analyses and highlights the need of targeted MS-based approaches for follow-up investigation. Additionally...

  6. Fixed target beams

    CERN Document Server

    Kain, V; Cettour-Cave, S; Cornelis, K; Fraser, M A; Gatignon, L; Goddard, B; Velotti, F

    2017-01-01

    The CERN SPS (Super Proton Synchrotron) serves asLHC injector and provides beam for the North Area fixedtarget experiments. At low energy, the vertical acceptancebecomes critical with high intensity large emittance fixed tar-get beams. Optimizing the vertical available aperture is a keyingredient to optimize transmission and reduce activationaround the ring. During the 2016 run a tool was developed toprovide an automated local aperture scan around the entirering.The flux of particles slow extracted with the1/3inte-ger resonance from the Super Proton Synchrotron at CERNshould ideally be constant over the length of the extractionplateau, for optimum use of the beam by the fixed target ex-periments in the North Area. The extracted intensity is con-trolled in feed-forward correction of the horizontal tune viathe main SPS quadrupoles. The Mains power supply noiseat 50 Hz and harmonics is also corrected in feed-forwardby small amplitude tune modulation at the respective fre-quencies with a dedicated additional quad...

  7. Aquaporin-2 membrane targeting

    DEFF Research Database (Denmark)

    Olesen, Emma T B; Fenton, Robert A

    2017-01-01

    The targeting of the water channel aquaporin-2 (AQP2) to the apical plasma membrane of kidney collecting duct principal cells is regulated mainly by the antidiuretic peptide hormone arginine vasopressin (AVP). This process is of crucial importance for the maintenance of body water homeostasis...... of aquaporin-2 (AQP2) to the apical plasma membrane of collecting duct (CD) principal cells (10, 20). This process is mainly regulated by the actions of AVP on the type 2 AVP receptor (V2R), although the V1a receptor may also play a minor role (26). The V2R is classified within the group of 7-transmembrane....... For example, 1) stimulation with the nonspecific AC activator forskolin increases AQP2 membrane accumulation in a mouse cortical collecting duct cell line [e.g., Norregaard et al. (16)]; 2) cAMP increases CD water permeability (15); 3) the cAMP-activated protein kinase A (PKA) can phosphorylate AQP2 on its...

  8. ORION laser target diagnostics

    International Nuclear Information System (INIS)

    Bentley, C. D.; Edwards, R. D.; Andrew, J. E.; James, S. F.; Gardner, M. D.; Comley, A. J.; Vaughan, K.; Horsfield, C. J.; Rubery, M. S.; Rothman, S. D.; Daykin, S.; Masoero, S. J.; Palmer, J. B.; Meadowcroft, A. L.; Williams, B. M.; Gumbrell, E. T.; Fyrth, J. D.; Brown, C. R. D.; Hill, M. P.; Oades, K.

    2012-01-01

    The ORION laser facility is one of the UK's premier laser facilities which became operational at AWE in 2010. Its primary mission is one of stockpile stewardship, ORION will extend the UK's experimental plasma physics capability to the high temperature, high density regime relevant to Atomic Weapons Establishment's (AWE) program. The ORION laser combines ten laser beams operating in the ns regime with two sub ps short pulse chirped pulse amplification beams. This gives the UK a unique combined long pulse/short pulse laser capability which is not only available to AWE personnel but also gives access to our international partners and visiting UK academia. The ORION laser facility is equipped with a comprehensive suite of some 45 diagnostics covering optical, particle, and x-ray diagnostics all able to image the laser target interaction point. This paper focuses on a small selection of these diagnostics.

  9. ORION laser target diagnostics.

    Science.gov (United States)

    Bentley, C D; Edwards, R D; Andrew, J E; James, S F; Gardner, M D; Comley, A J; Vaughan, K; Horsfield, C J; Rubery, M S; Rothman, S D; Daykin, S; Masoero, S J; Palmer, J B; Meadowcroft, A L; Williams, B M; Gumbrell, E T; Fyrth, J D; Brown, C R D; Hill, M P; Oades, K; Wright, M J; Hood, B A; Kemshall, P

    2012-10-01

    The ORION laser facility is one of the UK's premier laser facilities which became operational at AWE in 2010. Its primary mission is one of stockpile stewardship, ORION will extend the UK's experimental plasma physics capability to the high temperature, high density regime relevant to Atomic Weapons Establishment's (AWE) program. The ORION laser combines ten laser beams operating in the ns regime with two sub ps short pulse chirped pulse amplification beams. This gives the UK a unique combined long pulse/short pulse laser capability which is not only available to AWE personnel but also gives access to our international partners and visiting UK academia. The ORION laser facility is equipped with a comprehensive suite of some 45 diagnostics covering optical, particle, and x-ray diagnostics all able to image the laser target interaction point. This paper focuses on a small selection of these diagnostics.

  10. Optimal exploration target zones

    CSIR Research Space (South Africa)

    Debba, Pravesh

    2008-09-01

    Full Text Available prospective map are the weights-of-evidence (WofE) method logistic regression canonical favorability analysis neural networks evidential belief functions Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote.... . . ): FITNESS FUNCTION φWMSD+V(Sn) = λ N(A) ∑ −→x ∈A P(−→x ) ∣ ∣ ∣ ∣−→x −QSn( −→x ) ∣ ∣ ∣ ∣ +(1− λ)s2(OSn) , (2) where QSn( −→x ) is the location vector of an optimal exploration focal point in Sn nearest to −→x , and s2(OSn) is the variance...

  11. Bradycardia During Targeted Temperature Management

    DEFF Research Database (Denmark)

    Thomsen, Jakob Hartvig; Nielsen, Niklas; Hassager, Christian

    2016-01-01

    OBJECTIVES: Bradycardia is common during targeted temperature management, likely being a physiologic response to lower body temperature, and has recently been associated with favorable outcome following out-of-hospital cardiac arrest in smaller observational studies. The present study sought...... to confirm this finding in a large multicenter cohort of patients treated with targeted temperature management at 33°C and explore the response to targeted temperature management targeting 36°C. DESIGN: Post hoc analysis of a prospective randomized study. SETTING: Thirty-six ICUs in 10 countries. PATIENTS......: We studied 447 (targeted temperature management = 33°C) and 430 (targeted temperature management = 36°C) comatose out-of-hospital cardiac arrest patients with available heart rate data, randomly assigned in the targeted temperature management trial from 2010 to 2013. INTERVENTIONS: Targeted...

  12. Solid Polarized Targets and Applications

    International Nuclear Information System (INIS)

    Crabb, D. G.

    2008-01-01

    Examples are given of dynamically polarized targets in use today and how the subsystems have changed to meet the needs of todays experiments. Particular emphasis is placed on target materials such as ammonia and lithium deuteride. Recent polarization studies of irradiated materials such as butanol, deuterated butanol, polyethylene, and deuterated polyethylene are presented. The operation of two non-DNP target systems as well as applications of traditional DNP targets are briefly discussed

  13. Techniques for preparing isotopic targets

    International Nuclear Information System (INIS)

    Xu Guoji; Guan Shouren; Luo Xinghua; Sun Shuhua

    1987-12-01

    The techniques of making isotopic targets for nuclear physics experiments are introduced. Vacuum evaporation, electroplating, centrifugal precipitation, rolling and focused heavy-ion beam sputtering used to prepare various isotopic targets at IAE are described. Reduction-distillation with active metals and electrolytic reduction for converting isotope oxides to metals are mentioned. The stripping processes of producing self-supporting isotopic targets are summarized. The store methods of metallic targets are given

  14. Nova target diagnostics control system

    International Nuclear Information System (INIS)

    Severyn, J.R.

    1985-01-01

    During the past year the Nova target diagnostics control system was finished and put in service. The diagnostics loft constructed to the north of the target room provides the environmental conditions required to collect reliable target diagnostic data. These improvements include equipment cooling and isolation of the power source with strict control of instrumentation grounds to eliminate data corruption due to electromagnetic pulses from the laser power-conditioning system or from target implosion effects

  15. Stanford polarized atomic beam target

    International Nuclear Information System (INIS)

    Mavis, D.G.; Dunham, J.S.; Hugg, J.W.; Glavish, H.F.

    1976-01-01

    A polarized atomic beam source was used to produce an atomic hydrogen beam which was in turn used as a polarized proton target. A target density of 2 x 10'' atoms/cm 3 and a target polarization of 0.37 without the use of rf transitions were measured. These measurements indicate that a number of experiments are currently feasible with a variety of polarized target beams

  16. Targets for heavy ion fusion

    International Nuclear Information System (INIS)

    Clauser, M.J.

    1978-01-01

    This paper describes some of the basic principles of fusion target implosions, using some simple targets designed for irradiation by ion beams. Present estimates are that ion beams with 1-5 MJ, and 100-500 TW will be required to ignite high gain targets. (orig.) [de

  17. Beam heating of target foils

    International Nuclear Information System (INIS)

    Corwin, W.C.

    1975-01-01

    A target rotator, built to reduce the effects of beam spot heating, is fully adjustable, holds three targets, is chamber independent, and takes up limited space. The expected temperature rise in the target is calculated from the Stefan--Boltzmann law

  18. Hypoxia targeting copper complexes

    International Nuclear Information System (INIS)

    Dearling, J.L.

    1998-11-01

    The importance and incidence of tumour hypoxia, its measurement and current treatments available, including pharmacological and radiopharmacological methods of targeting hypoxia, are discussed. A variety of in vitro and in vivo methods for imposing hypoxia have been developed and are reviewed. Copper, its chemistry, biochemistry and radiochemistry, the potential for use of copper radionuclides and its use to date in this field is considered with particular reference to the thiosemicarbazones. Their biological activity, metal chelation, in vitro and in vivo studies of their radiocopper complexes and the potential for their use as hypoxia targeting radiopharmaceuticals is described. The reduction of the copper(II) complex to copper(l), its pivotal importance in their biological behaviour, and the potential for manipulation of this to effect hypoxia selectivity are described. An in vitro method for assessing the hypoxia selectivity of radiopharmaceuticals is reported. The rapid deoxygenation and high viability of a mammalian cell culture in this system is discussed and factors which may affect the cellular uptake of a radiopharmaceutical are described. The design, synthesis and complexation with copper and radiocopper of a range of bis(thiosemicarbazones) is reported. Synthesis of these compounds is simple giving high yields of pure products. The characteristics of the radiocopper complexes ( 64 Cu) including lipophilicity and redox activity are reported (reduction potentials in the range -0.314 - -0.590 V). High cellular uptakes of the radiocopper complexes of the ligands, in hypoxic and normoxic EMT6 and CHO320 cells, were observed. Extremes of selectivity are shown ranging from the hypoxia selective 64 Cu(II)ATSM to normoxic cell selective 64 Cu(II)GTS. The selectivities observed are compared with the physico chemical characteristics of the complexes. A good correlation exists between selectivity of the complex and its Cu(II)/Cu(I) reduction potential, with hypoxia

  19. Liquid hydrogen and deuterium targets

    International Nuclear Information System (INIS)

    Bougon, M.; Marquet, M.; Prugne, P.

    1961-01-01

    A description is given of 1) Atmospheric pressure target: liquid hydrogen, 400 mm thickness; thermal insulation: styrofoam; the hydrogen vapors are used to improve the target cooling; Mylar windows. 2) Vacuum target: 12 liter content: hydrogen or deuterium; liquid thickness 400 mm; thermal insulation is afforded by a vacuum vessel and a liquid nitrogen shield. Recovery and liquefaction of deuterium vapors are managed in the vacuum vessel which holds the target. The target emptying system is designed for operating in a few minutes. (author) [fr

  20. Isomeric Targets and Beams

    International Nuclear Information System (INIS)

    Oganesyan, Yu.Ts.; Karamyan, S.A.

    1994-01-01

    One of the main topics of modern nuclear physics is the investigation of exotic nuclei including hyper-nuclei, trans fermium elements, proton and neutron rich isotopes near drip lines as well as high-spin excited states and states with anomalous deformation. The isomerism of nuclei is closely related with such phenomena as the alignment of single-particle orbitals, the coexistence of various deformations and the manifestation of intruder-levels from neighbouring shells. The investigation of electromagnetic and nuclear interactions of isomers could give important information on their shell structure and its role in the mechanism of nuclear reactions. For such experiments one can either make isomeric targets (sufficiently long-lived) or use the methods of acceleration of isomeric nuclei. Recently, an exotic 16 + four-quasiparticle isomer of 178 Hf m 2 was produced in a micro weight quantity and the first nuclear reactions on it were successfully observed. The talk describes these experiments as well as new ideas for the continuation of the studies and some advantageous ways for the isomeric beams production by the method of direct acceleration or by the secondary beam method. 35 refs., 15 figs., 8 tabs

  1. EURISOL High Power Targets

    CERN Document Server

    Kadi, Y; Lindroos, M; Ridikas, D; Stora, T; Tecchio, L; CERN. Geneva. BE Department

    2009-01-01

    Modern Nuclear Physics requires access to higher yields of rare isotopes, that relies on further development of the In-flight and Isotope Separation On-Line (ISOL) production methods. The limits of the In-Flight method will be applied via the next generation facilities FAIR in Germany, RIKEN in Japan and RIBF in the USA. The ISOL method will be explored at facilities including ISAC-TRIUMF in Canada, SPIRAL-2 in France, SPES in Italy, ISOLDE at CERN and eventually at the very ambitious multi-MW EURISOL facility. ISOL and in-flight facilities are complementary entities. While in-flight facilities excel in the production of very short lived radioisotopes independently of their chemical nature, ISOL facilities provide high Radioisotope Beam (RIB) intensities and excellent beam quality for 70 elements. Both production schemes are opening vast and rich fields of nuclear physics research. In this article we will introduce the targets planned for the EURISOL facility and highlight some of the technical and safety cha...

  2. Molecularly targeted therapeutic radiopharmaceuticals

    International Nuclear Information System (INIS)

    Saw, M.M.

    2007-01-01

    Full text: It is generally agreed that current focus of nuclear medicine development should be on molecular imaging and therapy. Though, the widespread use of the terminology 'molecular imaging' is quite recent, nuclear medicine has used molecular imaging techniques for more than 20 years ago. A variety of radiopharmaceuticals have been introduced for the internal therapy of malignant and inflammatory lesions in nuclear medicine. In the field of bio/medical imaging, nuclear medicine is one of the disciplines which has the privilege of organized and well developed chemistry/ pharmacy section; radio-chemistry/radiopharmacy. Fundamental principles have been developed more than 40 years ago and advanced research is going well into postgenomic era. The genomic revolution and dramatically increased insight in the molecular mechanisms underlying pathology have led to paradigm shift in drug development. Likewise does in the nuclear medicine. Here, the author will present current clinical and pre-clinical therapeutic radiopharmaceuticals based on molecular targets such as membrane-bound receptors, enzymes, nucleic acids, sodium iodide symporter, etc, in correlation with fundamentals of radiopharmacy. (author)

  3. New type of metal targets

    International Nuclear Information System (INIS)

    Bukharov, A.V.; Ankudinov, V.B.; Ogorodnikov, V.P.; Marukhin, Y.A.

    2014-01-01

    Now the technologies based on interaction of high-intensity beams with substance of a target are being intensively developed. As a target it is possible to use the new type of monodisperse metal targets. The principal advantages of new targets type are: target cooling isn't required; there is no induced activity: the target can be used many times; small dispersion on the speed, the size and interaction points with a beam. The basis of a target is the jet of molten metal, following in the vacuum chamber .Under the influence of the special disturbance superimposed on the liquid jet, the jet disintegrated into identical drops. In the vacuum chamber the drops freeze and form into the solid granules. It is possible to receive monodisperse targets from different metals, alloys and salts (diameter of targets is from 30 .m to 1.5 mm). Dispersion by the sizes and speed is less than 1%. The technique allows to receive not only continuous targets, but also hollow targets with dispersion on thickness of wall within 1...2%.

  4. Using the Nova target chamber for high-yield targets

    International Nuclear Information System (INIS)

    Pitts, J.H.

    1987-01-01

    The existing 2.2-m-radius Nova aluminum target chamber, coated and lined with boron-seeded carbon shields, is proposed for use with 1000-MJ-yield targets in the next laser facility. The laser beam and diagnostic holes in the target chamber are left open and the desired 10 -2 Torr vacuum is maintained both inside and outside the target chamber; a larger target chamber room is the vacuum barrier to the atmosphere. The hole area available is three times that necessary to maintain a maximum fluence below 12 J/cm 2 on optics placed at a radius of 10 m. Maximum stress in the target chamber wall is 73 MPa, which complies with the intent of the ASME Pressure Vessel Code. However, shock waves passing through the inner carbon shield could cause it to comminute. We propose tests and analyses to ensure that the inner carbon shield survives the environment. 13 refs

  5. The target effect: visual memory for unnamed search targets.

    Science.gov (United States)

    Thomas, Mark D; Williams, Carrick C

    2014-01-01

    Search targets are typically remembered much better than other objects even when they are viewed for less time. However, targets have two advantages that other objects in search displays do not have: They are identified categorically before the search, and finding them represents the goal of the search task. The current research investigated the contributions of both of these types of information to the long-term visual memory representations of search targets. Participants completed either a predefined search or a unique-object search in which targets were not defined with specific categorical labels before searching. Subsequent memory results indicated that search target memory was better than distractor memory even following ambiguously defined searches and when the distractors were viewed significantly longer. Superior target memory appears to result from a qualitatively different representation from those of distractor objects, indicating that decision processes influence visual memory.

  6. Immunotherapy Targets in Pediatric Cancer

    Energy Technology Data Exchange (ETDEWEB)

    Orentas, Rimas J.; Lee, Daniel W.; Mackall, Crystal, E-mail: rimas.orentas@nih.gov, E-mail: mackallc@mail.nih.gov [Pediatric Oncology Branch, National Cancer Institute, National Institutes of Health, Bethesda, MD (United States)

    2012-01-30

    Immunotherapy for cancer has shown increasing success and there is ample evidence to expect that progress gleaned in immune targeting of adult cancers can be translated to pediatric oncology. This manuscript reviews principles that guide selection of targets for immunotherapy of cancer, emphasizing the similarities and distinctions between oncogene-inhibition targets and immune targets. It follows with a detailed review of molecules expressed by pediatric tumors that are already under study as immune targets or are good candidates for future studies of immune targeting. Distinctions are made between cell surface antigens that can be targeted in an MHC independent manner using antibodies, antibody derivatives, or chimeric antigen receptors versus intracellular antigens which must be targeted with MHC restricted T cell therapies. Among the most advanced immune targets for childhood cancer are CD19 and CD22 on hematologic malignancies, GD2 on solid tumors, and NY-ESO-1 expressed by a majority of synovial sarcomas, but several other molecules reviewed here also have properties which suggest that they too could serve as effective targets for immunotherapy of childhood cancer.

  7. Immunotherapy Targets in Pediatric Cancer

    International Nuclear Information System (INIS)

    Orentas, Rimas J.; Lee, Daniel W.; Mackall, Crystal

    2012-01-01

    Immunotherapy for cancer has shown increasing success and there is ample evidence to expect that progress gleaned in immune targeting of adult cancers can be translated to pediatric oncology. This manuscript reviews principles that guide selection of targets for immunotherapy of cancer, emphasizing the similarities and distinctions between oncogene-inhibition targets and immune targets. It follows with a detailed review of molecules expressed by pediatric tumors that are already under study as immune targets or are good candidates for future studies of immune targeting. Distinctions are made between cell surface antigens that can be targeted in an MHC independent manner using antibodies, antibody derivatives, or chimeric antigen receptors versus intracellular antigens which must be targeted with MHC restricted T cell therapies. Among the most advanced immune targets for childhood cancer are CD19 and CD22 on hematologic malignancies, GD2 on solid tumors, and NY-ESO-1 expressed by a majority of synovial sarcomas, but several other molecules reviewed here also have properties which suggest that they too could serve as effective targets for immunotherapy of childhood cancer.

  8. [Target volume margins for lung cancer: internal target volume/clinical target volume].

    Science.gov (United States)

    Jouin, A; Pourel, N

    2013-10-01

    The aim of this study was to carry out a review of margins that should be used for the delineation of target volumes in lung cancer, with a focus on margins from gross tumour volume (GTV) to clinical target volume (CTV) and internal target volume (ITV) delineation. Our review was based on a PubMed literature search with, as a cornerstone, the 2010 European Organisation for Research and Treatment of Cancer (EORTC) recommandations by De Ruysscher et al. The keywords used for the search were: radiotherapy, lung cancer, clinical target volume, internal target volume. The relevant information was categorized under the following headings: gross tumour volume definition (GTV), CTV-GTV margin (first tumoural CTV then nodal CTV definition), in field versus elective nodal irradiation, metabolic imaging role through the input of the PET scanner for tumour target volume and limitations of PET-CT imaging for nodal target volume definition, postoperative radiotherapy target volume definition, delineation of target volumes after induction chemotherapy; then the internal target volume is specified as well as tumoural mobility for lung cancer and respiratory gating techniques. Finally, a chapter is dedicated to planning target volume definition and another to small cell lung cancer. For each heading, the most relevant and recent clinical trials and publications are mentioned. Copyright © 2013. Published by Elsevier SAS.

  9. Facility target insert shielding assessment

    Energy Technology Data Exchange (ETDEWEB)

    Mocko, Michal [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-06

    Main objective of this report is to assess the basic shielding requirements for the vertical target insert and retrieval port. We used the baseline design for the vertical target insert in our calculations. The insert sits in the 12”-diameter cylindrical shaft extending from the service alley in the top floor of the facility all the way down to the target location. The target retrieval mechanism is a long rod with the target assembly attached and running the entire length of the vertical shaft. The insert also houses the helium cooling supply and return lines each with 2” diameter. In the present study we focused on calculating the neutron and photon dose rate fields on top of the target insert/retrieval mechanism in the service alley. Additionally, we studied a few prototypical configurations of the shielding layers in the vertical insert as well as on the top.

  10. Inertial-confinement-fusion targets

    International Nuclear Information System (INIS)

    Hendricks, C.D.

    1981-01-01

    Inertial confinement fusion (ICF) targets are made as simple flat discs, as hollow shells or as complicated multilayer structures. Many techniques have been devised for producing the targets. Glass and metal shells are made by using drop and bubble techniques. Solid hydrogen shells are also produced by adapting old methods to the solution of modern problems. Some of these techniques, problems and solutions are discussed. In addition, the applications of many of the techniques to fabrication of ICF targets is presented

  11. Targeted Nanotechnology for Cancer Imaging

    Science.gov (United States)

    Toy, Randall; Bauer, Lisa; Hoimes, Christopher; Ghaghada, Ketan B.; Karathanasis, Efstathios

    2014-01-01

    Targeted nanoparticle imaging agents provide many benefits and new opportunities to facilitate accurate diagnosis of cancer and significantly impact patient outcome. Due to the highly engineerable nature of nanotechnology, targeted nanoparticles exhibit significant advantages including increased contrast sensitivity, binding avidity and targeting specificity. Considering the various nanoparticle designs and their adjustable ability to target a specific site and generate detectable signals, nanoparticles can be optimally designed in terms of biophysical interactions (i.e., intravascular and interstitial transport) and biochemical interactions (i.e., targeting avidity towards cancer-related biomarkers) for site-specific detection of very distinct microenvironments. This review seeks to illustrate that the design of a nanoparticle dictates its in vivo journey and targeting of hard-to-reach cancer sites, facilitating early and accurate diagnosis and interrogation of the most aggressive forms of cancer. We will report various targeted nanoparticles for cancer imaging using X-ray computed tomography, ultrasound, magnetic resonance imaging, nuclear imaging and optical imaging. Finally, to realize the full potential of targeted nanotechnology for cancer imaging, we will describe the challenges and opportunities for the clinical translation and widespread adaptation of targeted nanoparticles imaging agents. PMID:25116445

  12. Target imaging and backlighting diagnosis

    International Nuclear Information System (INIS)

    Yaakobi, B.; Shvarts, D.; Marshall, F.J.; Epstein, R.; Su, Q.

    1995-01-01

    The expected backlighting and self-emission images of a particular CH target to be imploded on the Omega Upgrade are calculated for a variety of experimental parameters. It is shown that to overcome the problem of target self-emission, the image has to be monochromatized with a diffracting crystal. For the target studied, the two image components are then comparable in intensity and both provide useful information on target behavior. A particularly interesting feature is the appearance in the self-emission of a circular spike which closely delineates the fuel-shell interface, but requires high spatial resolution to be observed

  13. Biological Evaluation of 99mTc-HYNIC-EDDA/tricine-(Ser)-D4 Peptide for Tumor Targeting.

    Science.gov (United States)

    Kazemi, Ziba; Zahmatkesh, Mona Haddad; Abedi, Seyed Mohammad; Hosseinimehr, Seyed Jalal

    2017-08-24

    D4 small peptide (Leu-Ala-Arg-Leu-Leu-Thr) was selected as an appropriate agent for specific targeting of epidermal growth factor receptor (EGFR). The aim of study was to investigate the 99mTc-labeled D4 peptide for non-small cell lung tumor targeting. HYNIC-(Ser)3-D4 peptide was labeled with 99mTc using mixture of tricine and ethylenediamine diacetic acid (EDDA) as co-ligands. The in vitro cellular uptake of radiolabeled peptide was evaluated by blocking test on human non-small cell lung cancer (A-549) cell line and its biodistribution was evaluated in A-549 xenografted nude mice. This conjugated peptide was labeled with 99mTc in high radiochemical purity and it was highly stable in buffer and serum. The un-blocked to blocked cellular radioactivity ratio was 4- fold that showed a specific binding of this radiolabeled peptide on A-549 cell. Animal biodistribution in A-549 xenografted nude mice showed rapid clearance from blood and other non-target organs. Tumor uptake values as %ID/g (percentage of injection dose per gram of tissue) were 2.47% and 1.30% at 1 and 4 h after injection. This study showed the 99mTc-EDDA/tricine-HYNIC-(Ser)3-D4 peptide had tumor targeting on the non-small cell lung tumor. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  14. Literature evidence in open targets - a target validation platform.

    Science.gov (United States)

    Kafkas, Şenay; Dunham, Ian; McEntyre, Johanna

    2017-06-06

    We present the Europe PMC literature component of Open Targets - a target validation platform that integrates various evidence to aid drug target identification and validation. The component identifies target-disease associations in documents and ranks the documents based on their confidence from the Europe PMC literature database, by using rules utilising expert-provided heuristic information. The confidence score of a given document represents how valuable the document is in the scope of target validation for a given target-disease association by taking into account the credibility of the association based on the properties of the text. The component serves the platform regularly with the up-to-date data since December, 2015. Currently, there are a total number of 1168365 distinct target-disease associations text mined from >26 million PubMed abstracts and >1.2 million Open Access full text articles. Our comparative analyses on the current available evidence data in the platform revealed that 850179 of these associations are exclusively identified by literature mining. This component helps the platform's users by providing the most relevant literature hits for a given target and disease. The text mining evidence along with the other types of evidence can be explored visually through https://www.targetvalidation.org and all the evidence data is available for download in json format from https://www.targetvalidation.org/downloads/data .

  15. Oxide fuels and targets for transmutation

    International Nuclear Information System (INIS)

    Sudreau, F.; Bonnerot, J.M.; Warin, D.; Gaillard-Groleas, G.; Ferroud-Plattet, M.P.

    2007-01-01

    Full text of publication follows. Direction 1 of the French Act dated 30 December 1991 on the management of high-level, long-lived radioactive waste involves exploring solutions designed to separate long-lived radionuclides from the spent fuel and to transmute them under neutron flux into shorter half-lives or stable elements. In the French research programme conducted by CEA, these radionuclides are mainly minor actinides (americium, neptunium and curium) and fission products (particularly caesium, iodine and technetium). Within this context, this paper aims at illustrating the vast programme that CEA has performed in order to demonstrate the scientific and technical feasibility of minor actinide transmutation. An important part of the research was carried out in collaboration with French research (CNRS) and industrial (EDF, AREVA) organisations, and also in the framework of international co-operation programmes with the European Institute for Transuranium Elements in Karlsruhe (ITU), the US Department of Energy (DOE), the Japanese Atomic Energy Research Institute (now JAEA) and Central Research Institute of Electric Power Industry (CRIEPI) and the Russian Ministry for Atomic Energy (ROSATOM). Such research made it possible to evaluate the capacity of MOX fuels to be used as a support for minor actinide transmutation (homogeneous method). Simulations of pressurised water reactor (PWR) fuels have revealed the limits of this transmutation method, which are mainly related to the pressurization of the fuel rods and the formation of high active californium. On the contrary, for sodium-cooled fast reactor fuels possibly designed with large expansion plenums a first experimental demonstration of the transmutation of americium and neptunium has been successful in the Phenix reactor. Various studies designed to demonstrate the theoretical and experimental feasibility of transmutation using an inert support (heterogeneous method) have been carried out in HFR (EFTTRA

  16. A 1550-nm all-optical VCSEL-to-VCSEL wavelength conversion of a 8.5-Gb/s data signal and transmission over a 24.7-km fibre

    Science.gov (United States)

    Boiyo, D. Kiboi; Isoe, G. M.; Gamatham, R. R. G.; Leitch, A. W. R.; Gibbon, T. B.

    2016-02-01

    For the first time, we demonstrate, VCSEL-to-VCSEL wavelength conversion within the low attenuation 1550 nm window, including transmission over fibre and bit error rate (BER) performance characterization. We experimentally demonstrate a low injection power optical wavelength conversion by injecting an optical beam from a signal carrier master vertical cavity surface-emitting laser (VCSEL) into the side-mode of the slave VCSEL. This technique solves the challenge of wavelength collisions and also provides wavelength re-use in typical wavelength division multiplexed (WDM) systems. This paper, for the first time, uses two 1550 nm VCSELs with tunability range of 3 nm for a 5-9.8 mA bias current. The master VCSEL is modulated with a non-return-to-zero (NRZ) pseudo-random binary sequence (PRBS_27-1) 8.5 Gb/s data. A data conversion penalty of 1.1 dB is realized when a 15 dBm injection beam is used. The transmission performance of the converted wavelength from the slave VCSEL is evaluated using BER measurement at a 10-9 threshold. A 0.5 dB transmission penalty of the converted wavelength data is realized in an 8.5 Gb/s transmission over 24.7 km. This work is vital for optical fibre systems that may require wavelength switching for transmission of data signals.

  17. Did CDM particles of mass 2.47 x 10(-3) eV interact with precursor biopolymers and nucleic acids to initiate and boost lifeforms on Earth?

    Science.gov (United States)

    Rosen, Gerald

    2011-06-01

    Recent observations and theoretical studies have shown that non-baryonic Cold Dark Matter (CDM), which constitutes about 84% of all matter in the Universe, may feature a complex-scalar-field that carries particles of mass ≅ 2.47 x 10(-3)eV with the associated Compton range m(-1) ≅8.02 x 10(-3) cm, a distance on the scale of extended bionucleic acids and living cells. Such a complex-scalar-field can enter a weak-isospin Lorentz-invariant interaction that generates the flow of right-handed electrons and induces a chirality-imbued quantum chemistry on the m (-1) scale. A phenomenological Volterra-type equation is proposed for the CDM-impacted time development of N, the number of base pairs in the most advanced organism at Earth-age t. The solution to this equation suggests that the boosts in N at t ≅ 1.1 Gyr (advent of the first living prokaryotic cells), at t ≅ 2.9 Gyr (advent of eukaryotic single-celled organisms) and finally at t ≅ 4.0 Gyr (the Cambrian explosion) may be associated with three multi-Myr-duration cosmic showers of the complex-scalar-field CDM particles. If so, the signature of the particles may be detectible in Cambrian rocks.

  18. Internal Targeting and External Control: Phototriggered Targeting in Nanomedicine.

    Science.gov (United States)

    Arrue, Lily; Ratjen, Lars

    2017-12-07

    The photochemical control of structure and reactivity bears great potential for chemistry, biology, and life sciences. A key feature of photochemistry is the spatiotemporal control over secondary events. Well-established applications of photochemistry in medicine are photodynamic therapy (PDT) and photopharmacology (PP). However, although both are highly localizable through the application of light, they lack cell- and tissue-specificity. The combination of nanomaterial-based drug delivery and targeting has the potential to overcome limitations for many established therapy concepts. Even more privileged seems the merger of nanomedicine and cell-specific targeting (internal targeting) controlled by light (external control), as it can potentially be applied to many different areas of medicine and pharmaceutical research, including the aforementioned PDT and PP. In this review a survey of the interface of photochemistry, medicine and targeted drug delivery is given, especially focusing on phototriggered targeting in nanomedicine. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Radiopharmaceuticals targeting melanoma

    Energy Technology Data Exchange (ETDEWEB)

    Pham, T.Q.; Berghofer, P.; Liu, X.; Greguric, I.; Dikic, B.; Ballantyne, P.; Mattner, F.; Nguyen, V.; Loc' h, C.; Katsifis, A. [Radiopharmaceuticals Research Institute, Australian Nuclear Science and Technology Organisation, Menai, N.S.W., Sydney (Australia)

    2008-02-15

    Melanoma is one of the most aggressive cancers known with a high rate of mortality and increasing global incidence. So, the development of radiopharmaceuticals for either diagnostic or therapeutic purposes could make enormous contributions to melanoma patient health care. We have been studying melanoma tumours through several targeting mechanisms including melanin or specific receptor based radiopharmaceuticals Structure activity studies indicate that the substitution patterns on radioiodinated benzamides significantly influence the uptake mechanism from melanin to sigma-receptor binding. Furthermore, the position of the iodine as well as the presence of key functional groups and substituents has resulted in compounds with varying degrees of activity uptake and retention in tumours. From these results, a novel molecule 2-(2-(4-(4-iodo benzyl)piperazin-1-yl)-2-oxo-ethyl)isoindoline- 1,3-dione (M.E.L.037) was synthesized, labelled with iodine-123 and evaluated for application in melanoma tumour scintigraphy and radiotherapy. The tumour imaging potential of {sup 123}IM.E.L.037 was studied in vivo in C.57 B.L./ 6 J female mice bearing the B.16 F.0. murine melanoma tumour and in BALB/c nude mice bearing the A.375 human amelanotic melanoma tumour by biodistribution, competition studies and by SPECT imaging. {sup 123}I-M.E.L.037 exhibited high and rapid uptake in the B.16 F.0 melanoma tumour at 1 h (13 % I.D./g) increasing with time to reach 25 % I.D./g at 6 h. A significant uptake was also observed in the eyes (2% I.D., at 3-6 h p.i.) of black mice. No uptake was observed in the tumour or in the eyes of nude mice bearing the A.375 tumour. Due to high uptake and long retention in the tumour and rapid body clearance, standardized uptake values(S.U.V.) of {sup 123}I-M.E.L.037 were 30 and 60, at 24 and 48 h p.i.,respectively. SPECT imaging of mice bearing the B.16 melanoma indicated the radioactivity was predominately located in the tumour followed by the eyes, while no

  20. Target support for inertial confinement fusion

    International Nuclear Information System (INIS)

    Schultz, K.R.

    1995-08-01

    General Atomics (GA) plays an important industrial support role for the US Inertial Confinement Fusion (ICF) program in the area of target technology. This includes three major activities: target fabrication support, target handling systems development, and target chamber design. The work includes target fabrication for existing ICF experiments, target and target system development for future experiments, and target research and target chamber design for experiments on future machines, such as the National Ignition Facility (NIF)

  1. Target recognition by wavelet transform

    International Nuclear Information System (INIS)

    Li Zhengdong; He Wuliang; Zheng Xiaodong; Cheng Jiayuan; Peng Wen; Pei Chunlan; Song Chen

    2002-01-01

    Wavelet transform has an important character of multi-resolution power, which presents pyramid structure, and this character coincides the way by which people distinguish object from coarse to fineness and from large to tiny. In addition to it, wavelet transform benefits to reducing image noise, simplifying calculation, and embodying target image characteristic point. A method of target recognition by wavelet transform is provided

  2. High performance inertial fusion targets

    International Nuclear Information System (INIS)

    Nuckolls, J.H.; Bangerter, R.O.; Lindl, J.D.; Mead, W.C.; Pan, Y.L.

    1978-01-01

    Inertial confinement fusion (ICF) target designs are considered which may have very high gains (approximately 1000) and low power requirements (< 100 TW) for input energies of approximately one megajoule. These include targets having very low density shells, ultra thin shells, central ignitors, magnetic insulation, and non-ablative acceleration

  3. Treating rheumatoid arthritis to target

    DEFF Research Database (Denmark)

    Smolen, Josef S; Breedveld, Ferdinand C; Burmester, Gerd R

    2016-01-01

    BACKGROUND: Reaching the therapeutic target of remission or low-disease activity has improved outcomes in patients with rheumatoid arthritis (RA) significantly. The treat-to-target recommendations, formulated in 2010, have provided a basis for implementation of a strategic approach towards this t...

  4. Spinning targets for laser fusion

    International Nuclear Information System (INIS)

    Baldwin, D.E.; Ryutov, D.D.

    1995-09-01

    Several techniques for spinning the ICF targets up prior to or in the course of their compression are suggested. Interference of the rotational shear flow with Rayleigh-Taylor instability is briefly discussed and possible consequences for the target performance are pointed out

  5. Multiple Target Laser Designator (MTLD)

    Science.gov (United States)

    2007-03-01

    Optimized Liquid Crystal Scanning Element Optimize the Nonimaging Predictive Algorithm for Target Ranging, Tracking, and Position Estimation...commercial potential. 3.0 PROGRESS THIS QUARTER 3.1 Optimization of Nonimaging Holographic Antenna for Target Tracking and Position Estimation (Task 6) In

  6. Scheduling with target start times

    NARCIS (Netherlands)

    Hoogeveen, J.A.; Velde, van de S.L.; Klein Haneveld, W.K.; Vrieze, O.J.; Kallenberg, L.C.M.

    1997-01-01

    We address the single-machine problem of scheduling n independent jobs subject to target start times. Target start times are essentially release times that may be violated at a certain cost. The goal is to minimize an objective function that is composed of total completion time and maximum

  7. Optimum target thickness for polarimeters

    International Nuclear Information System (INIS)

    Sitnik, I.M.

    2003-01-01

    Polarimeters with thick targets are a tool to measure the proton polarization. But the question about the optimum target thickness is still the subject of discussion. An attempt to calculate the most common parameters concerning this problem, in a few GeV region, is made

  8. Target-Searching on Percolation

    International Nuclear Information System (INIS)

    Yang Shijie

    2005-01-01

    We study target-searching processes on a percolation, on which a hunter tracks a target by smelling odors it emits. The odor intensity is supposed to be inversely proportional to the distance it propagates. The Monte Carlo simulation is performed on a 2-dimensional bond-percolation above the threshold. Having no idea of the location of the target, the hunter determines its moves only by random attempts in each direction. For lager percolation connectivity p ∼> 0.90, it reveals a scaling law for the searching time versus the distance to the position of the target. The scaling exponent is dependent on the sensitivity of the hunter. For smaller p, the scaling law is broken and the probability of finding out the target significantly reduces. The hunter seems trapped in the cluster of the percolation and can hardly reach the goal.

  9. Targeted marketing and public health.

    Science.gov (United States)

    Grier, Sonya A; Kumanyika, Shiriki

    2010-01-01

    Targeted marketing techniques, which identify consumers who share common needs or characteristics and position products or services to appeal to and reach these consumers, are now the core of all marketing and facilitate its effectiveness. However, targeted marketing, particularly of products with proven or potential adverse effects (e.g., tobacco, alcohol, entertainment violence, or unhealthful foods) to consumer segments defined as vulnerable raises complex concerns for public health. It is critical that practitioners, academics, and policy makers in marketing, public health, and other fields recognize and understand targeted marketing as a specific contextual influence on the health of children and adolescents and, for different reasons, ethnic minority populations and other populations who may benefit from public health protections. For beneficial products, such understanding can foster more socially productive targeting. For potentially harmful products, understanding the nature and scope of targeted marketing influences will support identification and implementation of corrective policies.

  10. The Bering Target Tracking Instrumentation

    DEFF Research Database (Denmark)

    Denver, Troelz; Jørgensen, John Leif; Betto, Maurizio

    2003-01-01

    The key science instrument on the Bering satellite mission is a relative small telescope with an entrance aperture of 300 mm and a focal length between 500 and 1000 mm. The detection of potential targets is performed by one of the target scanning advanced stellar compasses (ASCs). This procedure...... results in a simple prioritized list of right ascension, declination, proper motion and intensity of each prospective target. The telescope itself has a dedicated ASC Camera Head Unit (CHU) mounted on the secondary mirror, largely co-aligned with the telescope. This CHU accurately determines the telescope......'s pointing direction. To achieve fast tracking over a large solid angle, the telescope pointing is achieved by means of a folding mirror in the optical pathway. When a prospective target approaches the telescope FOV, the ASC on the secondary will guide the folding mirror into position such that the target...

  11. Legal Issues in Cyber Targeting

    DEFF Research Database (Denmark)

    Juhlin, Jonas Alastair

    Imagine this scenario: Two states are in armed conflict with each other. In order to gain an advantage, one side launches a cyber-attack against the opponent’s computer network. The malicious malware paralyze the military computer network, as intended, but the malware spreads into the civilian...... system with physical damage to follow. This can happen and the natural question arises: What must be considered lawful targeting according to the international humanitarian law in cyber warfare? What steps must an attacker take to minimize the damage done to unlawful targets when conducting an offensive...... operation? How can the attacker separate military targets from civilian targets in cyber space? This paper addresses these questions and argues that a network (civilian or military) consist of several software components and that it is the individual components that is the target. If the components are used...

  12. Gas target neutron generator studies

    International Nuclear Information System (INIS)

    Chatoorgoon, V.

    1978-01-01

    The need for an intense neutron source for the study of radiation damage on materials has resulted in the proposal of various solid, liquid, and gas targets. Among the gas targets proposed have been the transonic gas target, two types of hypersonic gas target, and the subsonic gas target (SGT). It has been suggested that heat deposition in a subsonic channel might create a gas density step which would constitute an attractive gas target type. The first part of the present study examines this aspect of the SGT and shows that gas density gradients are indeed formed by heat deposition in subsonic flow. The variation of beam voltage, gas density, gas pressure, and gas temperature within the channel have been calculated as functions of the system parameters: beam voltage, beam current, channel diameter, stagnation tank temperature and pressure. The analysis is applicable to any beam particle and target gas. For the case of T + on D 2 , which is relevant to the fusion application, the 14 MeV neutron profiles are presented as a function of system parameters. It is found that the SGT is compatible with concentrated intense source operation. The possibility of instability was investigated in detail using a non-linear analysis which made it possible to follow the complete time development of the SGT. It was found that the SGT is stable against all small perturbations and certain types of large perturbations. It appears that the SGT is the most advantageous type of gas target, operating at a lower mass flow and less severe stagnation tank conditions than the other types. The second part of the thesis examines a problem associated with the straight hypersonic target, the deuterium spill into the tritium port. The regime of practical operation for this target is established. (auth)

  13. Preparation of thin nuclear targets

    International Nuclear Information System (INIS)

    Muggleton, A.H.F.

    1979-03-01

    Thin film backings, sources and targets are needed for many applications in low energy nuclear physics and nuclear chemistry experiments. A survey of techniques used in the preparation of nuclear targets is first briefly discussed. These are classified as chemical, mechanical and physical preparations. Vacuum evaporation, being the most generally used technique, is discussed in detail. It is highly desirable to monitor the film thickness and control the deposition rate during evaporation and to measure the final target thickness after deposition has concluded. The relative merits of various thickness measuring techniques are described. Stages in the fabrication and mounting of self-supporting foils are described in detail, with emphasis given to the preparation of thin self-supporting carbon foils used as target backings and stripper foils. Various target backings, and the merits of the more generally used release agents are described in detail. The preparations of more difficult elemental targets are discussed, and a comprehensive list of the common targets is presented

  14. Spallation source neutron target systems

    International Nuclear Information System (INIS)

    Russell, G.; Brown, R.; Collier, M.; Donahue, J.

    1996-01-01

    This is the final report for a two-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The project sought to design a next-generation spallation source neutron target system for the Manuel Lujan, Jr., Neutron Scattering Center (LANSCE) at Los Alamos. It has been recognized for some time that new advanced neutron sources are needed in the US if the country is to maintain a competitive position in several important scientific and technological areas. A recent DOE panel concluded that the proposed Advanced Neutron Source (a nuclear reactor at Oak Ridge National Laboratory) and a high-power pulsed spallation source are both needed in the near future. One of the most technically challenging designs for a spallation source is the target station itself and, more specifically, the target-moderator-reflector arrangement. Los Alamos has demonstrated capabilities in designing, building, and operating high-power spallation-neutron-source target stations. Most of the new design ideas proposed worldwide for target system design for the next generation pulsed spallation source have either been conceived and implemented at LANSCE or proposed by LANSCE target system designers. These concepts include split targets, flux-trap moderators, back scattering and composite moderators, and composite reflectors

  15. Simulations of effusion from ISOL target/ion source systems

    International Nuclear Information System (INIS)

    Mustapha, B.; Nolen, J.A.

    2004-01-01

    Monte Carlo simulations of the low- and high-conductivity Target/Ion Source systems used at Oak Ridge National Laboratory for effusion measurements are performed. Comparisons with the corresponding experimental data for the different geometries are presented and discussed. Independent checks of the simulation using data for simple geometries and using the conductance approach well known in vacuum technology are performed. A simulation-based comparison between the low- and high-conductivity systems is also presented

  16. PENETAPAN TARGET TERHADAP STICKINESS COST

    Directory of Open Access Journals (Sweden)

    Windyastuti Windyastuti

    2017-03-01

    Full Text Available This study aimed to analyze the influence of manager targeting to the stickiness cost. The research data was amanufacturing company’s financial statements during 1999-2011 published at BEI. The research data includedcost of sales, administration and general, net sales and Price Earnings Ratio (PER. This study used adynamic panel data regression analysis. The results showed that cost of sales, administration and general weresticky. Furthermore, manager targeting caused the stickiness degree of sales, administration and general costlower. Manager targeting changed the manager’s behavior. When the net sales declined, manager reduced theresource use drastically so the cost of sales, administration and general also decreased drastically.

  17. Development of targeted radiotherapy systems

    International Nuclear Information System (INIS)

    Ferro, Guillermina; Villarreal, Jose E.; Garcia, Laura; Tendilla, Jose I.; Paredes, Lydia; Murphy, Consuelo A.; Pedraza, Martha

    2001-01-01

    Conventional or external beam radiotherapy, has been a viable alternative for cancer treatment. Although this technique is effective, its use is limited if the patient has multiple malignant lesions (metastases). An alternative approach is based on the design of radiopharmaceuticals that, to be administered in the patient, are directed specifically toward the target cell producing a selective radiation delivery. This treatment is known as targeted radiotherapy. We have summarized and discussed some results related to our investigations on the development of targeted radiotherapy systems, including aspects of internal dosimetry

  18. Treating rheumatoid arthritis to target

    DEFF Research Database (Denmark)

    Smolen, Josef S; Aletaha, Daniel; Bijlsma, Johannes W J

    2010-01-01

    BACKGROUND: Aiming at therapeutic targets has reduced the risk of organ failure in many diseases such as diabetes or hypertension. Such targets have not been defined for rheumatoid arthritis (RA). OBJECTIVE: /st> To develop recommendations for achieving optimal therapeutic outcomes in RA. METHODS....... Levels of evidence, strength of recommendations and levels of agreement were derived. RESULTS: The treat-to-target activity resulted in 10 recommendations. The treatment aim was defined as remission with low disease activity being an alternative goal in patients with long-standing disease. Regular follow...

  19. A Cryogenic Infrared Calibration Target

    Science.gov (United States)

    Wollack, E. J.; Kinzer, R. E., Jr.; Rinehart, S. A.

    2014-01-01

    A compact cryogenic calibration target is presented that has a peak diffuse reflectance, R target. The resulting target assembly is lightweight, has a low-geometric profile, and has survived repeated thermal cycling from room temperature to approx.4 K. Basic design considerations, governing equations, and test data for realizing the structure described are provided. The optical properties of selected absorptive materials-Acktar Fractal Black, Aeroglaze Z306, and Stycast 2850 FT epoxy loaded with stainless steel powder-are characterized and presented

  20. 40 CFR 247.2 - Applicability.

    Science.gov (United States)

    2010-07-01

    ... apply to purchases made by private party recipients (e.g., individuals, non-profit organizations) of... competition, considering such guidelines. Procuring agencies may decide not to procure such items if they are...; or are only available at an unreasonable price. [60 FR 21381, May 1, 1995, as amended at 62 FR 60973...

  1. 32 CFR 247.4 - Policy.

    Science.gov (United States)

    2010-07-01

    ... for purchase, use, or patronage without regard to race, color, religion, sex, national origin, age...) Alteration of official photographic and video imagery will comply with DoD Directive 5040.5. 7 7 See footnote...

  2. 48 CFR 247.572 - Policy.

    Science.gov (United States)

    2010-10-01

    ... a vessel for which the contractor submitted an offer in response to the solicitation for the contract; and (ii) Prior to the acceptance of the vessel by the Government. (2) The Secretary of Defense... Act for Fiscal Year 2007 (Public Law 109-364)— (1) When obtaining carriage requiring a covered vessel...

  3. Publications | Page 247 | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    IDRC works with developing-country researchers and institutions to build local capacity through funding, knowledge sharing, and training. Through books, articles, research publications, and studies, we aim to widen the impact of our investment and advance development research. We share the results of our funded ...

  4. 40 CFR 247.15 - Landscaping products.

    Science.gov (United States)

    2010-07-01

    ... hydroseeding and as an over-spray for straw mulch in landscaping, erosion control, and soil reclamation. (b) Compost made from recovered organic materials. (c) Garden and soaker hoses containing recovered plastic or rubber. (d) Lawn and garden edging containing recovered plastic or rubber. (e) Plastic lumber landscaping...

  5. 40 CFR 247.3 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... thermophilic converted product with high humus content. Compost can be used as a soil amendment and can also be... be added to the water/seed mix for enhanced performance; Industrial drums are cylindrical containers... with applicable specifications, availability at a reasonable price, availability within a reasonable...

  6. 48 CFR 247.301-70 - Definition.

    Science.gov (United States)

    2010-10-01

    ... Definition. “Integrated logistics managers” or “third-party logistics providers” means providers of multiple logistics services. Some examples of logistics services are the management of transportation, demand...

  7. 32 CFR 247.6 - Procedures.

    Science.gov (United States)

    2010-07-01

    ... cohesiveness and effectiveness by providing a visual representation of the essence of the command itself. (G... defined purpose in support of the mission of the publishing DoD Component, and the purpose must justify...

  8. 32 CFR 247.3 - Definitions.

    Science.gov (United States)

    2010-07-01

    ...; commanders' comments; letters to the editor; editorials; commentaries; features; sports; entertainment items; morale, welfare, and recreation news and announcements; photography; line art; and installation and local...

  9. Toward a 24/7 Learning Community.

    Science.gov (United States)

    Revenaugh, Mickey

    2000-01-01

    Although nearly two-thirds of family households have computers and 46 percent have Internet connections, troubling income-related gaps persist. Parents want interactive connections with teachers, homework hotlines, and tutoring services more than school web sites. Web-quest models, laptops, and computer donation programs are promising…

  10. Alta disponibilidad 24/7 : el reto

    OpenAIRE

    López Grande, Carlos Edgardo; Guadrón Gutiérrez, Ricardo Salvador

    2015-01-01

    En la actualidad, las actividades diarias para los ne- gocios, instituciones, instituciones educativas o nivel de usuario común están directamente vinculadas a la red de redes, la Internet. Su desarrollo ha permitido a la mayoría de los servicios y aplicaciones, que hace años eran sólo para el modo cliente-servidor, ahora acceder desde cualquier lugar en cualquier dispositi- vo con conexión a Internet. Por lo tanto, ofrecer un ambiente que da conexiones y transacciones 7/24 es necesario para ...

  11. 40 CFR 61.247 - Reporting requirements.

    Science.gov (United States)

    2010-07-01

    ...) Method of compliance with the standard (for example, “monthly leak detection and repair” or “equipped...) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Equipment Leaks... identification. (ii) Type of equipment (for example, a pump or pipeline valve). (iii) Percent by weight VHAP in...

  12. 25 CFR 700.247 - Appeals.

    Science.gov (United States)

    2010-04-01

    ... envelope containing the notice of appeal and the face of the notice shall bear the legend “FREEDOM OF INFORMATION APPEAL”. The failure of an appeal to bear such a legend will not disqualify an appeal from...

  13. 7 CFR 247.34 - Management reviews.

    Science.gov (United States)

    2010-01-01

    ... administration on an ongoing basis by reviewing financial reports, audit reports, food orders, inventory reports... the State agency do to ensure that local agencies meet program requirements and objectives? The State..., and other agencies conducting program activities meet program requirements and objectives. As part of...

  14. 8 CFR 247.11 - Notice.

    Science.gov (United States)

    2010-01-01

    ... Nationality DEPARTMENT OF HOMELAND SECURITY IMMIGRATION REGULATIONS ADJUSTMENT OF STATUS OF CERTAIN RESIDENT... and upon his request have an opportunity to appear in person, in support or in lieu of his written answer, before an immigration officer designated for that purpose. The person shall further be advised...

  15. 40 CFR 247.12 - Construction products.

    Science.gov (United States)

    2010-07-01

    ..., polyisocyanurate, polystyrene, phenolics, and composites; and (4) Spray-in-place insulation, including but not limited to foam-in-place polyurethane and polyisocyanurate, and spray-on cellulose. (b) Structural...

  16. Effectiveness of accelerated perioperative care and rehabilitation intervention compared to current intervention after hip and knee arthroplasty. A before-after trial of 247 patients with a 3-month follow-up

    Directory of Open Access Journals (Sweden)

    Hansen Torben B

    2008-04-01

    Full Text Available Abstract Background In Denmark, approximately 12,000 hip and knee arthroplasties were performed in 2006, and the hospital costs were close to US$ 110,000,000. In a randomized clinical trial, we have recently demonstrated the efficacy of accelerated perioperative care and rehabilitation intervention after hip and knee arthroplasty compared to current intervention under ideal circumstances. We do not, however, know whether these results could be reached under usual circumstances of healthcare practice. We therefore investigated whether length of stay after implementation of accelerated perioperative care and rehabilitation after hip and knee arthroplasty could be reduced in a normal healthcare setting, and how the achieved results matched those observed during the randomized clinical trial. Methods An effectiveness study as a before-after trial was undertaken in which all elective primary total hip and total knee arthroplasty patients were divided into a before-implementation group receiving the current perioperative procedure, and an after-implementation group receiving the new accelerated perioperative care and rehabilitation procedures as provided by a new multi-disciplinary organization. We used the Breakthrough Series Collaborative Model for implementation. The primary outcome measure was in hospital length of stay (LOS, and the secondary outcome measure was adverse effects within 3 months postoperatively. Results We included a total of 247 patients. Mean LOS was significantly (P Conclusion Accelerated perioperative care and rehabilitation intervention after hip and knee arthroplasty was successfully and effectively implemented. Results obtained during usual hospital circumstances matched the results achieved under ideal circumstances in this group of patients.

  17. Obstacles to Effective Joint Targeting

    National Research Council Canada - National Science Library

    Patch, John

    2007-01-01

    .... Notwithstanding the most precise and capable weaponry ever, any targeting effort absent coherent strategy or executed outside the art and rules of war can spell campaign defeat even amidst tactical successes...

  18. Immunotherapy Targets Common Cancer Mutation

    Science.gov (United States)

    In a study of an immune therapy for colorectal cancer that involved a single patient, researchers identified a method for targeting the cancer-causing protein produced by a mutant form of the KRAS gene.

  19. Tracking Target and Spiral Waves

    DEFF Research Database (Denmark)

    Jensen, Flemming G.; Sporring, Jon; Nielsen, Mads

    2002-01-01

    A new algorithm for analyzing the evolution of patterns of spiral and target waves in large aspect ratio chemical systems is introduced. The algorithm does not depend on finding the spiral tip but locates the center of the pattern by a new concept, called the spiral focus, which is defined...... by the evolutes of the actual spiral or target wave. With the use of Gaussian smoothing, a robust method is developed that permits the identification of targets and spirals foci independently of the wave profile. Examples of an analysis of long image sequences from experiments with the Belousov......–Zhabotinsky reaction catalyzed by ruthenium-tris-bipyridyl are presented. Moving target and spiral foci are found, and the speed and direction of movement of single as well as double spiral foci are investigated. For the experiments analyzed in this paper it is found that the movement of a focus correlates with foci...

  20. Obstacles to Effective Joint Targeting

    National Research Council Canada - National Science Library

    Patch, John

    2007-01-01

    No foe can beat the modern-day American military machine in combined arms warfare, yet this machine is subject to strategic targeting vulnerabilities that military and policy leaders would do well to appreciate...

  1. Vascular targeting with peptide libraries

    Energy Technology Data Exchange (ETDEWEB)

    Pasqualini, R. [La Jolla Cancer Research Center The Burnham Inst., La Jolla CA (United States)

    1999-06-01

    The authors have developed an 'in vivo' selection system in which phage capable of selective homing to different tissues are recovered from a phage display peptide library following intravenous administration. Using this strategy, they have isolate several organ and tumor-homing peptides. They have shown that each of those peptides binds of different receptors that are selectively expressed on the vasculature of the target tissue. The tumor-homing peptides bind to receptors that are up regulated in tumor angiogenic vasculature. Targeted delivery of doxorubicin to angiogenic vasculature using these peptides in animals models decrease toxicity and increased the therapeutic efficacy of the drug. Vascular targeting may facilitate the development of other treatment strategies that rely on inhibition of angio genesis and lead to advances to extend the potential for targeting of drugs, genes and radionuclides in the context of many diseases.

  2. Navy Advertising: Targeting Generation Z

    Science.gov (United States)

    2015-12-01

    NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA MBA PROFESSIONAL REPORT NAVY ADVERTISING : TARGETING GENERATION Z December......study recommends improvements for Navy advertising efficiency by examining characteristics of recruits defined as Generation Z. Data gathered from five

  3. Physics of Automatic Target Recognition

    CERN Document Server

    Sadjadi, Firooz

    2007-01-01

    Physics of Automatic Target Recognition addresses the fundamental physical bases of sensing, and information extraction in the state-of-the art automatic target recognition field. It explores both passive and active multispectral sensing, polarimetric diversity, complex signature exploitation, sensor and processing adaptation, transformation of electromagnetic and acoustic waves in their interactions with targets, background clutter, transmission media, and sensing elements. The general inverse scattering, and advanced signal processing techniques and scientific evaluation methodologies being used in this multi disciplinary field will be part of this exposition. The issues of modeling of target signatures in various spectral modalities, LADAR, IR, SAR, high resolution radar, acoustic, seismic, visible, hyperspectral, in diverse geometric aspects will be addressed. The methods for signal processing and classification will cover concepts such as sensor adaptive and artificial neural networks, time reversal filt...

  4. Inertial-confinement-fusion targets

    International Nuclear Information System (INIS)

    Hendricks, C.D.

    1982-01-01

    Much of the research in laser fusion has been done using simple ball on-stalk targets filled with a deuterium-tritium mixture. The targets operated in the exploding pusher mode in which the laser energy was delivered in a very short time (approx. 100 ps or less) and was absorbed by the glass wall of the target. The high energy density in the glass literally exploded the shell with the inward moving glass compressing the DT fuel to high temperatures and moderate densities. Temperatures achieved were high enough to produce DT reactions and accompanying thermonuclear neutrons and alpha particles. The primary criteria imposed on the target builders were: (1) wall thickness, (2) sphere diameter, and (3) fuel in the sphere

  5. Targeted intraoperative radiotherapy in oncology

    CERN Document Server

    Keshtgar, Mohammed; Wenz, Frederik

    2014-01-01

    Targeted intraoperative radiotherapy is a major advance in the management of cancer patients. With an emphasis on practical aspects, this book offers an ideal introduction to this innovative  technology for clinicians.

  6. Special hydrogen target (Prop. 210)

    International Nuclear Information System (INIS)

    Halliday, C.E.

    1979-11-01

    This guide contains a description of the electrical control and automatic vacuum systems for the Special Hydrogen Target (Prop. 210) together with the flow diagram and the mimic control panel layout for the system. (U.K.)

  7. National Ignition Facility Target Chamber

    International Nuclear Information System (INIS)

    Wavrik, R W; Cox, J R; Fleming, P J

    2000-01-01

    On June 11, 1999 the Department of Energy dedicated the single largest piece of the National Ignition Facility (NIF) at Lawrence Livermore National Laboratory (LLNL) in Livermore, California. The ten (10) meter diameter aluminum target high vacuum chamber will serve as the working end of the largest laser in the world. The output of 192 laser beams will converge at the precise center of the chamber. The laser beams will enter the chamber in two by two arrays to illuminate 10 millimeter long gold cylinders called hohlraums enclosing 2 millimeter capsule containing deuterium, tritium and isotopes of hydrogen. The two isotopes will fuse, thereby creating temperatures and pressures resembling those found only inside stars and in detonated nuclear weapons, but on a minute scale. The NIF Project will serve as an essential facility to insure safety and reliability of our nation's nuclear arsenal as well as demonstrating inertial fusion's contribution to creating electrical power. The paper will discuss the requirements that had to be addressed during the design, fabrication and testing of the target chamber. A team from Sandia National Laboratories (SNL) and LLNL with input from industry performed the configuration and basic design of the target chamber. The method of fabrication and construction of the aluminum target chamber was devised by Pitt-Des Moines, Inc. (PDM). PDM also participated in the design of the chamber in areas such as the Target Chamber Realignment and Adjustment System, which would allow realignment of the sphere laser beams in the event of earth settlement or movement from a seismic event. During the fabrication of the target chamber the sphericity tolerances had to be addressed for the individual plates. Procedures were developed for forming, edge preparation and welding of individual plates. Construction plans were developed to allow the field construction of the target chamber to occur parallel to other NIF construction activities. This was

  8. Theoretical aspects of inflation targeting

    Directory of Open Access Journals (Sweden)

    Obradović Jelena

    2014-01-01

    Full Text Available Inflation targeting is one of the possible strategies used by central banks during conducting monetary policy. The basic characteristics, advantages and disadvantages of inflation targeting will be presented in this paper. The focus is on the the presentation and interpretation of the understanding of this strategy from the perspective of monetarist and Keynesian theory, the theory of rational expectations, and methodological analysis of the strategy in light of the game theory using payoff matrix.

  9. Targeting Splicing in Prostate Cancer

    OpenAIRE

    Effrosyni Antonopoulou; Michael Ladomery

    2018-01-01

    Over 95% of human genes are alternatively spliced, expressing splice isoforms that often exhibit antagonistic functions. We describe genes whose alternative splicing has been linked to prostate cancer; namely VEGFA, KLF6, BCL2L2, ERG, and AR. We discuss opportunities to develop novel therapies that target specific splice isoforms, or that target the machinery of splicing. Therapeutic approaches include the development of small molecule inhibitors of splice factor kinases, splice isoform speci...

  10. Targeting BRCAness in Gastric Cancer

    Science.gov (United States)

    2017-10-01

    Award Number: W81XWH-16-1-0472 TITLE: Targeting BRCAness in Gastric Cancer PRINCIPAL INVESTIGATOR: Lawrence Fong CONTRACTING ORGANIZATION...Targeting BRCAness in Gastric Cancer 5b. GRANT NUMBER W81XWH-16-1-0473 (Ashworth) 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Eric Collisson, David Quigley...for Public Release; Distribution Unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT We performed the screen of gastric cancer cell lines for their

  11. Targeting Quiescence in Prostate Cancer

    Science.gov (United States)

    2017-10-01

    AWARD NUMBER: W81XWH-15-1-0413 TITLE: Targeting Quiescence in Prostate Cancer PRINCIPAL INVESTIGATOR: Laura Buttitta CONTRACTING...Quiescence in Prostate Cancer 5a. CONTRACT NUMBER Targeting uiescence in Prostate Cancer 5b. GRANT NUMBER W81XWH-15-1-0413 5c. PROGRAM ELEMENT NUMBER 6...NOTES 14. ABSTRACT A major problem in prostate cancer is finding and eliminating the non-proliferating or “quiescent” cancer cells. This is because early

  12. Targeting BRCAness in Gastric Cancer

    Science.gov (United States)

    2017-10-01

    Award Number: W81XWH-16-1-0470 TITLE: Targeting BRCAness in Gastric Cancer PRINCIPAL INVESTIGATOR: Yelena Janjigian CONTRACTING ORGANIZATION...Sloan-Kettering Institute for Cancer Research New York, NY 10065 REPORT DATE: October 2017 TYPE OF REPORT: Annual PREPARED FOR: U.S. Army Medical...Targeting BRCAness in Gastric Cancer 5b. GRANT NUMBER W81XWH-16-1-0473 (Ashworth) 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Eric Collisson, David

  13. Gas target with thin wall

    International Nuclear Information System (INIS)

    Korenchenko, A.S.; Korenchenko, S.M.; Kravchuk, N.P.; Filippov, A.I.; Fursov, A.P.

    1992-01-01

    The technology of targets manufacture with thin wall diameter 100 mm and lengthwise 700 mm from composition kevlar + epoxy resin is described. The test's results on pressure and vacuum are reported. The created targets are supposed to be used on the installation ARES for an investigation of muons and pions interactions with light nuclei and rare pions decay 'on flying'. 5 refs.; 2 figs.; 2 tabs

  14. Targeted immunotherapy in Hodgkin lymphoma

    DEFF Research Database (Denmark)

    Hutchings, Martin

    2015-01-01

    In this issue of Blood, Rothe et al introduce a new principle of targeted Hodgkin lymphoma (HL) immunotherapy in their report from a phase 1 study of the bispecific anti-CD30/CD16A antibody construct AFM13.......In this issue of Blood, Rothe et al introduce a new principle of targeted Hodgkin lymphoma (HL) immunotherapy in their report from a phase 1 study of the bispecific anti-CD30/CD16A antibody construct AFM13....

  15. X-ray tube target

    International Nuclear Information System (INIS)

    Weber, R.G.

    1980-01-01

    A target with an improved heat emissive surface for use in a rotating anode type x-ray tube is described. The target consists of a body having a first surface portion made of x-ray emissive material and a second surface portion made of a heat emissive material comprising at least one of hafnium boride, hafnium oxide, hafnium nitride, hafnium silicide, and hafnium aluminide. (U.K.)

  16. Polarized atomic beams for targets

    International Nuclear Information System (INIS)

    Grueebler, W.

    1984-01-01

    The basic principle of the production of polarized atomic hydrogen and deuterium beams are reviewed. The status of the present available polarization, density and intensity are presented. The improvement of atomic beam density by cooling the hydrogen atoms to low velocity is discussed. The possible use of polarized atomic beams as targets in storage rings is shown. It is proposed that polarized atomic beams can be used to produce polarized gas targets with high polarization and greatly improved density

  17. Market segmentation, targeting and positioning

    OpenAIRE

    Camilleri, Mark Anthony

    2017-01-01

    Businesses may not be in a position to satisfy all of their customers, every time. It may prove difficult to meet the exact requirements of each individual customer. People do not have identical preferences, so rarely does one product completely satisfy everyone. Many companies may usually adopt a strategy that is known as target marketing. This strategy involves dividing the market into segments and developing products or services to these segments. A target marketing strategy is focused on ...

  18. Theranostics Targeting Metastatic Breast Cancer

    Science.gov (United States)

    2016-10-01

    Knapp DW. Targeting folate receptors to treat invasive urinary bladder cancer . Cancer Res 2013;73(2):875–884. 71. Holm J, Hansen SI, Hoier-Madsen M...purpose of this review, active targeting in cancer research encompasses strategies wherein a ligand for a cell surface receptor expressed on tumor...trafficking, thus impacting the efficacy of receptor -mediated drug delivery for cancer therapy. These factors include the following: (i) the rate of ligand

  19. Target-oriented chaos control

    International Nuclear Information System (INIS)

    Dattani, Justine; Blake, Jack C.H.; Hilker, Frank M.

    2011-01-01

    Designing intervention methods to control chaotic behavior in dynamical systems remains a challenging problem, in particular for systems that are difficult to access or to measure. We propose a simple, intuitive technique that modifies the values of the state variables directly toward a certain target. The intervention takes into account the difference to the target value, and is a combination of traditional proportional feedback and constant feedback methods. It proves particularly useful when the target corresponds to the equilibrium of the uncontrolled system, and is available or can be estimated from expert knowledge (e.g. in biology and economy). -- Highlights: → We propose a chaos control method that forces the system to a certain target. → The intervention takes into account the difference to the target value. → It can be seen as a combination of proportional and constant feedback methods. → The method is very robust and highly efficient in the long-term. → It is particularly applicable when suitable target values are known or available.

  20. Target cells in internal dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Goessner, W

    2003-07-01

    Data related to radium induced bone sarcomas in humans are used as a model for defining target cells on bone surfaces and in the bone marrow. The differential distribution of radiation induced bone sarcoma types with a high ratio of non-bone producing, mainly fibroblastic tumours, challenges the ICRP concept that the bone lining cells are target cells. Multipotential mesenchymal stem cells are located within the range of alpha particles, and are the most likely target cells for the fibroblastic type of bone sarcoma. The histogenesis of bone sarcomas after irradiation with alpha emitters shows that their final histopathology is not dependent on a single target cell. Each target cell has a microenvironment, which has to be regarded as a synergistic morpho-functional tissue unit. For this the concept of 'histion', a term used in general pathology, is proposed. Interactions between target cells that have been hit by alpha-particles, leading to lethal, mutational or transformation events with all components of a 'histion', will prove critical to understanding the pathogenesis of both deterministic and stochastic late effects. (author)

  1. Target cells in internal dosimetry

    International Nuclear Information System (INIS)

    Goessner, W.

    2003-01-01

    Data related to radium induced bone sarcomas in humans are used as a model for defining target cells on bone surfaces and in the bone marrow. The differential distribution of radiation induced bone sarcoma types with a high ratio of non-bone producing, mainly fibroblastic tumours, challenges the ICRP concept that the bone lining cells are target cells. Multipotential mesenchymal stem cells are located within the range of alpha particles, and are the most likely target cells for the fibroblastic type of bone sarcoma. The histogenesis of bone sarcomas after irradiation with alpha emitters shows that their final histopathology is not dependent on a single target cell. Each target cell has a microenvironment, which has to be regarded as a synergistic morpho-functional tissue unit. For this the concept of 'histion', a term used in general pathology, is proposed. Interactions between target cells that have been hit by alpha-particles, leading to lethal, mutational or transformation events with all components of a 'histion', will prove critical to understanding the pathogenesis of both deterministic and stochastic late effects. (author)

  2. Target assignment for security officers to K targets (TASK)

    International Nuclear Information System (INIS)

    Rowland, J.R.; Shelton, K.W.; Stunkel, C.B.

    1983-02-01

    A probabilistic algorithm is developed to provide an optimal Target Assignment for Security officers to K targets (TASK) using a maximin criterion. Under the assumption of only a limited number (N) of security officers, the TASK computer model determines deployment assignments which maximize the system protection against sabotage by an adversary who may select any link in the system, including the weakest, for the point of attack. Applying the TASK model to a hypothetical nuclear facility containing a nine-level building reveals that aggregate targets covering multiple vital areas should be utilized to reduce the number of possible target assignments to a value equal to or only slightly larger than N. The increased probability that a given aggregate target is covered by one or more security officers offsets the slight decrease in interruption probability due to its occurring earlier in the adversary's path. In brief, the TASK model determines the optimal maximin deployment strategy for limited numbers of security officers and calculates a quantitative measure of the resulting system protection

  3. Progress in ISOL target-ion source systems

    Energy Technology Data Exchange (ETDEWEB)

    Koester, U. [Institut Laue Langevin, 6 Rue Jules Horowitz, F-38042 Grenoble Cedex 9 (France); ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland)], E-mail: koester@ill.fr; Arndt, O. [HGF VISTARS and Institut fuer Kernchemie, Johannes-Gutenberg Universitaet Mainz, D-55128 Mainz (Germany); Bouquerel, E.; Fedoseyev, V.N. [ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland); Franberg, H. [ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland); Laboratory for Radio- and Environmental Chemistry, Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Joinet, A. [ISOLDE, CERN, CH-1211 Geneve 23 (Switzerland); Centre d' Etude Spatiale des Rayonnements, 9 Av. du Colonel Roche, F-31028 Toulouse Cedex 4 (France); Jost, C. [HGF VISTARS and Institut fuer Kernchemie, Johannes-Gutenberg Universitaet Mainz, D-55128 Mainz (Germany); Kerkines, I.S.K. [Laboratory of Physical Chemistry, National and Kapodistrian University of Athens, Department of Chemistry, Zografou 157 71, GR (Greece); Cherry L. Emerson Center for Scientific Computation and Department of Chemistry, Emory University, Atlanta, GA 30322 (United States); Kirchner, R. [Gesellschaft fuer Schwerionenforschung, Planckstr. 1, D-64291 Darmstadt (Germany)

    2008-10-15

    The heart of every ISOL (isotope separation on-line) facility is its target and ion source system. Its efficiency, selectivity and rapidity is decisive for the production of intense and pure ion beams of short-lived isotopes. Recent progress in ISOL target and ion source technology is discussed at the examples of radioactive ion beams of exotic zinc and tin isotopes that were purified by isothermal chromatography and molecular sideband separation respectively. An outlook is given to which other elements these purification methods are applicable.

  4. Progress in ISOL target-ion source systems

    International Nuclear Information System (INIS)

    Koester, U.; Arndt, O.; Bouquerel, E.; Fedoseyev, V.N.; Franberg, H.; Joinet, A.; Jost, C.; Kerkines, I.S.K.; Kirchner, R.

    2008-01-01

    The heart of every ISOL (isotope separation on-line) facility is its target and ion source system. Its efficiency, selectivity and rapidity is decisive for the production of intense and pure ion beams of short-lived isotopes. Recent progress in ISOL target and ion source technology is discussed at the examples of radioactive ion beams of exotic zinc and tin isotopes that were purified by isothermal chromatography and molecular sideband separation respectively. An outlook is given to which other elements these purification methods are applicable.

  5. Review of polarized ammonium target

    International Nuclear Information System (INIS)

    Matsuda, Tatsuo

    1987-01-01

    Recently, ammonia (NH 3 ) and deutron ammonia (ND 3 ), instead of conventional alcohol substances, have been used more frequently as a polarized target substance for experiments of polarization at high energy regions. This article reviews major features of the polarized (deutron) ammonia targets. The dynamic nuclear polarization (DNT) method is widely used in high energy polarization experiments. While only a low polarization degree of hydrogen nucleus of 1.7 percent can be obtained by the Brute force method, DNP can produce polarization as high as ∼ 90 percent (2.5 T, ∼ 200 mK). In 1979, ammonia was irradiated with radiations to form NH 2 free radicals, resulting in the achievement of a high polarization degree of greater than 90 percent (hydrogen). Since then, ammonia and deutron ammonia have increasingly been replacing alcohols including butanol. Irradiation of a target substance with radiations destroys the structure of the substance, leading to a decrease in polarization degree. However, ammonia produces unpaired electrons as a result of irradiation, allowing it to be highly resistant to radiation. This report also present some study results, including observations on effects of radiation on the polarization degree of a target, effects of annealing, and polarization of 14 N. A process for producing an ammonia target is also described. (Nogami, K.)

  6. Polymeric micelles for drug targeting.

    Science.gov (United States)

    Mahmud, Abdullah; Xiong, Xiao-Bing; Aliabadi, Hamidreza Montazeri; Lavasanifar, Afsaneh

    2007-11-01

    Polymeric micelles are nano-delivery systems formed through self-assembly of amphiphilic block copolymers in an aqueous environment. The nanoscopic dimension, stealth properties induced by the hydrophilic polymeric brush on the micellar surface, capacity for stabilized encapsulation of hydrophobic drugs offered by the hydrophobic and rigid micellar core, and finally a possibility for the chemical manipulation of the core/shell structure have made polymeric micelles one of the most promising carriers for drug targeting. To date, three generations of polymeric micellar delivery systems, i.e. polymeric micelles for passive, active and multifunctional drug targeting, have arisen from research efforts, with each subsequent generation displaying greater specificity for the diseased tissue and/or targeting efficiency. The present manuscript aims to review the research efforts made for the development of each generation and provide an assessment on the overall success of polymeric micellar delivery system in drug targeting. The emphasis is placed on the design and development of ligand modified, stimuli responsive and multifunctional polymeric micelles for drug targeting.

  7. China's energy efficiency target 2010

    International Nuclear Information System (INIS)

    Yang Ming

    2008-01-01

    The Chinese government has set an ambitious target: reducing China's energy intensity by 20%, or 4.36% each year between 2006 and 2010 on the 2005 level. Real data showed that China missed its target in 2006, having reduced its energy intensity only by 1.3%. The objective of this study is to evaluate the feasibility and potential of the Chinese to achieve the target. This paper presents issues of macro-economy, population migration, energy savings, and energy efficiency policy measures to achieve the target. A top-down approach was used to analyse the relationship between the Chinese economic development and energy demand cycles and to identify the potentials of energy savings in sub-sectors of the Chinese economy. A number of factors that contribute to China's energy intensity are identified in a number of energy-intensive sectors. This paper concludes that China needs to develop its economy at its potential GDP growth rate; strengthen energy efficiency auditing, monitoring and verification; change its national economy from a heavy-industry-dominated mode to a light industry or a commerce-dominated mode; phase out inefficient equipment in industrial sectors; develop mass and fast railway transportation; and promote energy-efficient technologies at the end use. This paper transfers key messages to policy makers for designing their policy to achieve China's energy efficiency target

  8. A triple axes multiple target holder assembly

    International Nuclear Information System (INIS)

    Tribedi, L.C.; Narvekar, S.D.; Pillay, R.G.; Tandon, P.N.

    1993-01-01

    We have designed and fabricated a rotatable target holder assembly capable of accommodating 27 targets. The target foils are mounted along two concentric circles on a ss wheel. On the outer circle 18 targets can be mounted each 20deg apart, and on the inner circle the remaining targets are positioned each 40deg apart. The self supporting or carbon backed targets are mounted on thin frames and are placed concentrically at the targets are mounted on thin frames and are placed concentrically at the target position on the wheel. Three degrees of freedom are provided to the target holder assembly. (author). 1 fig

  9. Target-Centric Network Modeling

    DEFF Research Database (Denmark)

    Mitchell, Dr. William L.; Clark, Dr. Robert M.

    In Target-Centric Network Modeling: Case Studies in Analyzing Complex Intelligence Issues, authors Robert Clark and William Mitchell take an entirely new approach to teaching intelligence analysis. Unlike any other book on the market, it offers case study scenarios using actual intelligence...... reporting formats, along with a tested process that facilitates the production of a wide range of analytical products for civilian, military, and hybrid intelligence environments. Readers will learn how to perform the specific actions of problem definition modeling, target network modeling......, and collaborative sharing in the process of creating a high-quality, actionable intelligence product. The case studies reflect the complexity of twenty-first century intelligence issues by dealing with multi-layered target networks that cut across political, economic, social, technological, and military issues...

  10. 3-Bromopyruvate: targets and outcomes.

    Science.gov (United States)

    Shoshan, Maria C

    2012-02-01

    The pyruvate mimetic 3-bromopyruvate (3-BP) is generally presented as an inhibitor of glycolysis and has shown remarkable efficacy in not only preventing tumor growth, but even eradicating existant tumors in animal studies. We here review reported molecular targets of 3-BP and suggest that the very range of possible targets, which pertain to the altered energy metabolism of tumor cells, contributes both to the efficacy and the tumor specificity of the drug. Its in vivo efficacy is suggested to be due to a combination of glycolytic and mitochondrial targets, as well as to secondary effects affecting the tumor microenvironment. The cytotoxicity of 3-BP is less due to pyruvate mimicry than to alkylation of, e.g., key thiols. Alkylation of DNA/RNA has not been reported. More research is warranted to better understand the pharmacokinetics of 3-BP, and its potential toxic effects to normal cells, in particular those that are highly ATP-/mitochondrion-dependent.

  11. Pharmacogenomics of GPCR Drug Targets

    DEFF Research Database (Denmark)

    Hauser, Alexander Sebastian; Chavali, Sreenivas; Masuho, Ikuo

    2018-01-01

    Natural genetic variation in the human genome is a cause of individual differences in responses to medications and is an underappreciated burden on public health. Although 108 G-protein-coupled receptors (GPCRs) are the targets of 475 (∼34%) Food and Drug Administration (FDA)-approved drugs...... and account for a global sales volume of over 180 billion US dollars annually, the prevalence of genetic variation among GPCRs targeted by drugs is unknown. By analyzing data from 68,496 individuals, we find that GPCRs targeted by drugs show genetic variation within functional regions such as drug......- and effector-binding sites in the human population. We experimentally show that certain variants of μ-opioid and Cholecystokinin-A receptors could lead to altered or adverse drug response. By analyzing UK National Health Service drug prescription and sales data, we suggest that characterizing GPCR variants...

  12. Voyager 2 Neptune targeting strategy

    Science.gov (United States)

    Potts, C. L.; Francis, K.; Matousek, S. E.; Cesarone, R. J.; Gray, D. L.

    1989-01-01

    The success of the Voyager 2 flybys of Neptune and Triton depends upon the ability to correct the spacecraft's trajectory. Accurate spacecraft delivery to the desired encounter conditions will promote the maximum science return. However, Neptune's great distance causes large a priori uncertainties in Neptune and Triton ephemerides and planetary system parameters. Consequently, the 'ideal' trajectory is unknown beforehand. The targeting challenge is to utilize the gradually improving knowledge as the spacecraft approaches Neptune to meet the science objectives, but with an overriding concern for spacecraft safety and a desire to limit propellant expenditure. A unique targeting strategy has been developed in response to this challenge. Through the use of a Monte Carlo simulation, candidate strategies are evaluated by the degree to which they meet these objectives and are compared against each other in determining the targeting strategy to be adopted.

  13. The Bering Autonomous Target Detection

    DEFF Research Database (Denmark)

    Jørgensen, John Leif; Denver, Troelz; Betto, Maurizio

    2003-01-01

    An autonomous asteroid target detection and tracking method has been developed. The method features near omnidirectionality and focus on high speed operations and completeness of search of the near space rather than the traditional faint object search methods, employed presently at the larger...... telescopes. The method has proven robust in operation and is well suited for use onboard spacecraft. As development target for the method and the associated instrumentation the asteroid research mission Bering has been used. Onboard a spacecraft, the autonomous detection is centered around the fully...... autonomous star tracker the Advanced Stellar Compass (ASC). One feature of this instrument is that potential targets are registered directly in terms of date, right ascension, declination, and intensity, which greatly facilitates both tracking search and registering. Results from ground and inflight tests...

  14. INFLATION TARGETING IN EASTERN EUROPE

    Directory of Open Access Journals (Sweden)

    Laurian Lungu

    2006-05-01

    Full Text Available This paper addresses the inflation targeting approach in three transition economies, namely Hungary, Poland and the Czech Republic with the use of Taylor rules as benchmarks. The three economies considered have been successful at achieving disinflation, but deviations of inflation from its target have been persistent in all cases. Except for the Czech Republic, deviations from the Taylor rule are large and persistent, with Hungary displaying the largest fluctuations. Polish interest rates have consistently exceeded those suggested by the Taylor rule and given the prevalence of high unemployment, these undershootings do not augur well for the stability of monetary policy. Finally, the behaviour of Czech interest rates can be remarkably captured by the simple Taylor rule proposed in this paper, suggesting that the Czech National Bank has been the most successful at stabilising inflation and output around their target levels.

  15. High-efficiency target-ion sources for RIB generation

    International Nuclear Information System (INIS)

    Alton, G.D.

    1993-01-01

    A brief review is given of high-efficiency ion sources which have been developed or are under development at ISOL facilities which show particular promise for use at existing, future, or radioactive ion beam (RIB) facilities now under construction. Emphasis will be placed on those sources which have demonstrated high ionization efficiency, species versatility, and operational reliability and which have been carefully designed for safe handling in the high level radioactivity radiation fields incumbent at such facilities. Brief discussions will also be made of the fundamental processes which affect the realizable beam intensities in target-ion sources. Among the sources which will be reviewed will be selected examples of state-of-the-art electron-beam plasma-type ion sources, thermal-ionization, surface-ionization, ECR, and selectively chosen ion source concepts which show promise for radioactive ion beam generation. A few advanced, chemically selective target-ion sources will be described, such as sources based on the use of laser-resonance ionization, which, in principle, offer a more satisfactory solution to isobaric contamination problems than conventional electromagnetic techniques. Particular attention will be given to the sources which have been selected for initial or future use at the Holifield Radioactive Ion Beam Facility now under construction at the Oak Ridge National Laboratory

  16. Materials considerations in accelerator targets

    International Nuclear Information System (INIS)

    Peacock, H. B. Jr.; Iyer, N. C.; Louthan, M. R. Jr.

    1995-01-01

    Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from, the coextruded product was modeled from experimental and operational data. The model assumed that tritium atoms, formed by the 6Li(n,a)3He reaction, were produced in solid solution in the Al-Li alloy. Because of the low solubility of hydrogen isotopes in aluminum alloys, the irradiated Al-Li rapidly became supersaturated in tritium. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes

  17. Materials considerations in accelerator targets

    International Nuclear Information System (INIS)

    Peacock, H.B. Jr.; Iyer, N.C.; Louthan, M.R. Jr.

    1994-01-01

    Future nuclear materials production and/or the burn-up of long lived radioisotopes may be accomplished through the capture of spallation produced neutrons in accelerators. Aluminum clad-lead and/or lead alloys has been proposed as a spallation target. Aluminum was the cladding choice because of the low neutron absorption cross section, fast radioactivity decay, high thermal conductivity, and excellent fabricability. Metallic lead and lead oxide powders were considered for the target core with the fabrication options being casting or powder metallurgy (PM). Scoping tests to evaluate gravity casting, squeeze casting, and casting and swaging processes showed that, based on fabricability and heat transfer considerations, squeeze casting was the preferred option for manufacture of targets with initial core cladding contact. Thousands of aluminum clad aluminum-lithium alloy core targets and control rods for tritium production have been fabricated by coextrusion processes and successfully irradiated in the SRS reactors. Tritium retention in, and release from the coextruded product was modeled from experimental and operational data. Newly produced tritium atoms were trapped by lithium atoms to form a lithium tritide. The effective tritium pressure required for trap or tritide stability was the equilibrium decomposition pressure of tritium over a lithium tritide-aluminum mixture. The temperature dependence of tritium release was determined by the permeability of the cladding to tritium and the local equilibrium at the trap sites. The model can be used to calculate tritium release from aluminum clad, aluminum-lithium alloy targets during postulated accelerator operational and accident conditions. This paper describes the manufacturing technologies evaluated and presents the model for tritium retention in aluminum clad, aluminum-lithium alloy tritium production targets

  18. Apparatus for producing laser targets

    International Nuclear Information System (INIS)

    Jarboe, T.R.; Baker, W.R.

    1975-01-01

    This patent relates to an apparatus and method for producing deuterium targets or pellets of 25u to 75u diameter. The pellets are sliced from a continuously spun solid deuterium thread at a rate of up to 10 pellets/second. The pellets after being sliced from the continuous thread of deuterium are collimated and directed to a point of use, such as a laser activated combustion or explosion chamber wherein the pellets are imploded by laser energy or laser produced target plasmas for neutral beam injection

  19. Theranostics Targeting Metastatic Breast Cancer

    Science.gov (United States)

    2017-10-01

    AWARD NUMBER: W81XWH-15-1-0390 TITLE: Theranostics Targeting Metastatic Breast Cancer PRINCIPAL INVESTIGATOR: Zheng Li CONTRACTING ORGANIZATION...Breast Cancer 5b. GRANT NUMBER W81XWH-15-1-0390 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER Zheng Li 5e. TASK NUMBER 5f. WORK UNIT...14 Theranostics Targeting Metastatic Breast  Cancer   A. Introduction (1paragraph) The overall goal of this proposal is to prepare TrkC

  20. Targeting vaccines to dendritic cells

    DEFF Research Database (Denmark)

    Foged, Camilla; Sundblad, Anne; Hovgaard, Lars

    2002-01-01

    delivery systems (DDS) with adjuvant effect that target DC directly and induce optimal immune responses. This paper will review the current knowledge of DC physiology as well as the progress in the field of novel vaccination strategies that directly or indirectly aim at targeting DC....... to be far superior to that of B-cells and macrophages. DC are localized at strategic places in the body at sites used by pathogens to enter the organism, and are thereby in an optimal position to capture antigens. In general, vaccination strategies try to mimic the invasiveness of the pathogens. DC...

  1. Targeted therapies for bone sarcomas

    International Nuclear Information System (INIS)

    Mudry, P.

    2011-01-01

    Therapy success in bone sarcoma is significantly better compared to history cohorts with 60 - 70 % overall survival to date. Unfortunately, there is yet no shift and movement in better survival of patients with relapsed and refractory bone sarcomas during last twenty years. This article reviews targeted therapeutics for bone sarcomas which are under investigation and which could give chance to patients suffering from relapsed and chemo resistant bone sarcomas. Majority of the targeted drugs are given as part of phase 1 or 2 studies. (author)

  2. The OPERA experiment Target Tracker

    CERN Document Server

    Adam, T; Borer, K.; Campagne, Jean-Eric; Con-Sen, N.; de La Taille, C.; Dick, N.; Dracos, M.; Gaudiot, G.; Goeltzenlichter, T.; Gornushkin, Y.; Grapton, J.-N.; Guyonnet, J.-L.; Hess, M.; Igersheim, R.; Janicsko Csathy, J.; Jollet, C.; Juget, F.; Kocher, H.; Krasnoperov, A.; Krumstein, Z.; Martin-Chassard, G.; Moser, U.; Nozdrin, A.; Olchevski, A.; Porokhovoi, S.; Raux, L.; Sadovski, A.; Schuler, J.; Schutz, H.-U.; Schwab, C.; Smolnikov, A.; Van Beek, G.; Vilain, P.; Walchli, T.; Wilquet, G.; Wurtz, J.

    2007-01-01

    The main task of the Target Tracker detector of the long baseline neutrino oscillation OPERA experiment is to locate in which of the target elementary constituents, the lead/emulsion bricks, the neutrino interactions have occurred and also to give calorimetric information about each event. The technology used consists in walls of two planes of plastic scintillator strips, one per transverse direction. Wavelength shifting fibres collect the light signal emitted by the scintillator strips and guide it to both ends where it is read by multi-anode photomultiplier tubes. All the elements used in the construction of this detector and its main characteristics are described.

  3. X-ray tube targets

    International Nuclear Information System (INIS)

    Hirsch, H.H.

    1980-01-01

    In rotary targets for X-ray tubes warping is a problem which causes X-ray deficiency. A rotary target is described in which warping is reduced by using alloys of molybdenum with 0.05 to 10% iron, silicon, cobalt, tantalum, niobium, hafnium, stable metal oxide or mixture thereof. Suitable mixtures are 0.5 to 10% of tantalum, niobium or hafnium with from 0.5 to 5% yttrium oxide, or 0.05 to 0.3% of cobalt or silicon. Optionally 0.1 to 5% by weight of additional material may be alloyed with the molybdenum, such as tantalum or hafnium carbides. (author)

  4. State-Targeted Funding and Technical Assistance to Increase Access to Medication Treatment for Opioid Use Disorder.

    Science.gov (United States)

    Abraham, Amanda J; Andrews, Christina M; Grogan, Colleen M; Pollack, Harold A; D'Aunno, Thomas; Humphreys, Keith; Friedmann, Peter D

    2018-04-01

    As the United States grapples with an opioid epidemic, expanding access to effective treatment for opioid use disorder is a major public health priority. Identifying effective policy tools that can be used to expand access to care is critically important. This article examines the relationship between state-targeted funding and technical assistance and adoption of three medications for treating opioid use disorder: oral naltrexone, injectable naltrexone, and buprenorphine. This study draws from the 2013-2014 wave of the National Drug Abuse Treatment System Survey, a nationally representative, longitudinal study of substance use disorder treatment programs. The sample includes data from 695 treatment programs (85.5% response rate) and representatives from single-state agencies in 49 states and Washington, D.C. (98% response rate). Logistic regression was used to examine the relationships of single-state agency targeted funding and technical assistance to availability of opioid use disorder medications among treatment programs. State-targeted funding was associated with increased program-level adoption of oral naltrexone (adjusted odds ratio [AOR]=3.14, 95% confidence interval [CI]=1.49-6.60, p=.004) and buprenorphine (AOR=2.47, 95% CI=1.31-4.67, p=.006). Buprenorphine adoption was also correlated with state technical assistance to support medication provision (AOR=1.18, 95% CI=1.00-1.39, p=.049). State-targeted funding for medications may be a viable policy lever for increasing access to opioid use disorder medications. Given the historically low rates of opioid use disorder medication adoption in treatment programs, single-state agency targeted funding is a potentially important tool to reduce mortality and morbidity associated with opioid disorders and misuse.

  5. Nuclear Security: Target Analysis-rev

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Surinder Paul [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gibbs, Philip W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bultz, Garl A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-03-01

    The objectives of this presentation are to understand target identification, including roll-up and protracted theft; evaluate target identification in the SNRI; recognize the target characteristics and consequence levels; and understand graded safeguards.

  6. Uranium briquettes for irradiation target

    Energy Technology Data Exchange (ETDEWEB)

    Saliba-Silva, Adonis Marcelo; Garcia, Rafael Henrique Lazzari; Martins, Ilson Carlos; Carvalho, Elita Fontenele Urano de; Durazzo, Michelangelo, E-mail: saliba@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    Direct irradiation on targets inside nuclear research or multiple purpose reactors is a common route to produce {sup 99}Mo-{sup 99m}Tc radioisotopes. Nevertheless, since the imposed limits to use LEU uranium to prevent nuclear armament production, the amount of uranium loaded in target meats has physically increased and new processes have been proposed for production. Routes using metallic uranium thin film and UAl{sub x} dispersion have been used for this purpose. Both routes have their own issues, either by bringing difficulties to disassemble the aluminum case inside hot cells or by generating great amount of alkaline radioactive liquid rejects. A potential route might be the dispersion of powders of LEU metallic uranium and nickel, which are pressed as a blend inside a die and followed by pulse electroplating of nickel. The electroplating provides more strength to the briquettes and creates a barrier for gas evolution during neutronic disintegration of {sup 235}U. A target briquette platted with nickel encapsulated in an aluminum case to be irradiated may be an alternative possibility to replace other proposed targets. This work uses pulse Ni-electroplating over iron powder briquette to simulate the covering of uranium by nickel. The following parameters were applied 10 times for each sample: 900Hz, -0.84A/square centimeters with duty cycle of 0.1 in Watts Bath. It also presented the optical microscopy analysis of plated microstructure section. (author)

  7. Natural products to target inflammation

    NARCIS (Netherlands)

    Allijn, Iris Eva

    2016-01-01

    Chapter 1 Most Western lifestyle diseases such as type 2 diabetes mellitus, cardiovascular disease and cancer have a chronic inflammatory process at its base. Therefore, inflammation is an important therapeutic target. Due to their potency, steroidal drugs dominate the current treatment of

  8. Particle physics using nuclear targets

    International Nuclear Information System (INIS)

    Ferbel, T.

    1978-01-01

    The use of nuclear targets in particle physics is discussed and some recent results obtained in studies of hadronic interactions on nuclei summarized. In particular experimental findings on inclusive production and on coherent dissociation of mesons and baryons at high energies are presented. 41 references

  9. Targeted drugs in radiation therapy

    International Nuclear Information System (INIS)

    Favaudon, V.; Hennequin, C.; Hennequin, C.

    2004-01-01

    New drugs aiming at the development of targeted therapies have been assayed in combination with ionizing radiation over the past few years. The rationale of this concept comes from the fact that the cytotoxic potential of targeted drugs is limited, thus requiring concomitant association with a cytotoxic agent for the eradication of tumor cells. Conversely a low level of cumulative toxicity is expected from targeted drugs. Most targeted drugs act through inhibition of post-translational modifications of proteins, such as dimerization of growth factor receptors, prenylation reactions, or phosphorylation of tyrosine or serine-threonine residues. Many systems involving the proteasome, neo-angiogenesis promoters, TGF-β, cyclooxygenase or the transcription factor NF-κB, are currently under investigation in hopes they will allow a control of cell proliferation, apoptosis, cell cycle progression, tumor angiogenesis and inflammation. A few drugs have demonstrated an antitumor potential in particular phenotypes. In most instances, however, radiation-drug interactions proved to be strictly additive in terms of cell growth inhibition or induced cell death. Strong potentiation of the response to radiotherapy is expected to require interaction with DNA repair mechanisms. (authors)

  10. Targeted nanoparticles for colorectal cancer

    DEFF Research Database (Denmark)

    Cisterna, Bruno A.; Kamaly, Nazila; Choi, Won Il

    2016-01-01

    Colorectal cancer (CRC) is highly prevalent worldwide, and despite notable progress in treatment still leads to significant morbidity and mortality. The use of nanoparticles as a drug delivery system has become one of the most promising strategies for cancer therapy. Targeted nanoparticles could...

  11. CERN neutrino project on target

    CERN Multimedia

    2005-01-01

    Scientists at CERN announced the completion of the target assembly for the CERN neutrinos to Gran Sasso project, CNGS. On schedule for start-up in May 2006, CNGS will send a beam of neutrinos through the Earth to the Gran Sasso laboratory 730 km away in Italy in a bid to unravel the mysteries of nature's most elusive particles (½ page)

  12. High performance inertial fusion targets

    International Nuclear Information System (INIS)

    Nuckolls, J.H.; Bangerter, R.O.; Lindl, J.D.; Mead, W.C.; Pan, Y.L.

    1977-01-01

    Inertial confinement fusion (ICF) designs are considered which may have very high gains (approximately 1000) and low power requirements (<100 TW) for input energies of approximately one megajoule. These include targets having very low density shells, ultra thin shells, central ignitors, magnetic insulation, and non-ablative acceleration

  13. Ion backscattering from layered targets

    International Nuclear Information System (INIS)

    Oen, O.S.; Robinson, M.T.

    1985-01-01

    The present work investigated the reflection of hydrogen atoms, whose incident energy ranged from 0.01 to 1 keV, from layered targets. The calculations used the binary collisions computer program MARLOWE modified to treat layered target structures. Briefly, the projectile ion strikes the surface normally and is followed collision-by-collision until it leaves the surface again or until its energy falls below a present value (1 eV). Each collision consists of an elastic and an inelastic part. The elastic part is treated by classical scattering mechanics using the Moliere approximation to the Thomas-Fermi interatomic potential with the screening lengths proposed by Firsov. The inelastic part is described by the (nonlocal) electronic stopping theory of Lindhard et al. The calculations were made using MARLOWE to simulate amorphous solids, and a typical run consisted of following the motions of 1000-2000 incident particles. The targets studied were chosen to have large differences between the atomic numbers of the overlayer and the substrate in order to emphasize possible reflection differences from that of monoatomic targets

  14. Distinguishing targets in armed conflict

    African Journals Online (AJOL)

    The main object of international humanitarian law (IHL) is the amelioration of the effect of armed conflict on the populace. It seeks to accomplish this by establishing rules that ensure that objects the destruction of which will not give military advantage e are protected; thus, such objects are not to be targeted or destroyed.

  15. Pharmacogenomics of GPCR Drug Targets

    DEFF Research Database (Denmark)

    Hauser, Alexander Sebastian; Chavali, Sreenivas; Masuho, Ikuo

    2018-01-01

    Natural genetic variation in the human genome is a cause of individual differences in responses to medications and is an underappreciated burden on public health. Although 108 G-protein-coupled receptors (GPCRs) are the targets of 475 (∼34%) Food and Drug Administration (FDA)-approved drugs and a...

  16. Communicating to heterogeneous target groups

    DEFF Research Database (Denmark)

    Pedersen, Karsten

    very often have to communicate to rather heterogeneous target groups that have little more in common than a certain geographical habitat. That goes against most schoolbook teaching in the field of communication, but is none the less the terms with which that kind of communication has to live...

  17. Uranium briquettes for irradiation target

    International Nuclear Information System (INIS)

    Saliba-Silva, Adonis Marcelo; Garcia, Rafael Henrique Lazzari; Martins, Ilson Carlos; Carvalho, Elita Fontenele Urano de; Durazzo, Michelangelo

    2011-01-01

    Direct irradiation on targets inside nuclear research or multiple purpose reactors is a common route to produce 99 Mo- 99m Tc radioisotopes. Nevertheless, since the imposed limits to use LEU uranium to prevent nuclear armament production, the amount of uranium loaded in target meats has physically increased and new processes have been proposed for production. Routes using metallic uranium thin film and UAl x dispersion have been used for this purpose. Both routes have their own issues, either by bringing difficulties to disassemble the aluminum case inside hot cells or by generating great amount of alkaline radioactive liquid rejects. A potential route might be the dispersion of powders of LEU metallic uranium and nickel, which are pressed as a blend inside a die and followed by pulse electroplating of nickel. The electroplating provides more strength to the briquettes and creates a barrier for gas evolution during neutronic disintegration of 235 U. A target briquette platted with nickel encapsulated in an aluminum case to be irradiated may be an alternative possibility to replace other proposed targets. This work uses pulse Ni-electroplating over iron powder briquette to simulate the covering of uranium by nickel. The following parameters were applied 10 times for each sample: 900Hz, -0.84A/square centimeters with duty cycle of 0.1 in Watts Bath. It also presented the optical microscopy analysis of plated microstructure section. (author)

  18. How are inflation targets set?

    Czech Academy of Sciences Publication Activity Database

    Horváth, R.; Matějů, Jakub

    -, č. 426 (2010), s. 1-35 ISSN 1211-3298 Grant - others:MŠk(CZ) SVV-2010-261801 Institutional research plan: CEZ:MSM0021620846 Keywords : inflation targeting * central bank * credibility Subject RIV: AH - Economics http://www.cerge-ei.cz/pdf/wp/Wp426.pdf

  19. Harnessing off-target effects

    DEFF Research Database (Denmark)

    Saginc, Gaye; Voellmy, Franziska; Linding, Rune

    2017-01-01

    The 'off-targets' of a drug are often poorly characterized yet could be harnessed in the treatment of complex diseases. A recent study used a small-molecule screening in non-small-cell lung cancer to repurpose an FDA-approved ALK/IGF1R inhibitor and uncover its mechanism of action....

  20. The Automatic Measurement of Targets

    DEFF Research Database (Denmark)

    Höhle, Joachim

    1997-01-01

    The automatic measurement of targets is demonstrated by means of a theoretical example and by an interactive measuring program for real imagery from a réseau camera. The used strategy is a combination of two methods: the maximum correlation coefficient and the correlation in the subpixel range...... interactive software is also part of a computer-assisted learning program on digital photogrammetry....

  1. Aptamers for Targeted Drug Delivery

    Directory of Open Access Journals (Sweden)

    Partha Ray

    2010-05-01

    Full Text Available Aptamers are a class of therapeutic oligonucleotides that form specific three-dimensional structures that are dictated by their sequences. They are typically generated by an iterative screening process of complex nucleic acid libraries employing a process termed Systemic Evolution of Ligands by Exponential Enrichment (SELEX. SELEX has traditionally been performed using purified proteins, and cell surface receptors may be challenging to purify in their properly folded and modified conformations. Therefore, relatively few aptamers have been generated that bind cell surface receptors. However, improvements in recombinant fusion protein technology have increased the availability of receptor extracellular domains as purified protein targets, and the development of cell-based selection techniques has allowed selection against surface proteins in their native configuration on the cell surface. With cell-based selection, a specific protein target is not always chosen, but selection is performed against a target cell type with the goal of letting the aptamer choose the target. Several studies have demonstrated that aptamers that bind cell surface receptors may have functions other than just blocking receptor-ligand interactions. All cell surface proteins cycle intracellularly to some extent, and many surface receptors are actively internalized in response to ligand binding. Therefore, aptamers that bind cell surface receptors have been exploited for the delivery of a variety of cargoes into cells. This review focuses on recent progress and current challenges in the field of aptamer-mediated delivery.

  2. Target selection for direct marketing.

    NARCIS (Netherlands)

    Bult, Jan Roelf

    1993-01-01

    In this thesis we concentrated on the use ol direct mail for targeting potential buyers. The major characteristics that influences the success of a plomotional direct mail campaign are the of-fbr,the communication elements, the timing or sequence of these communication elements, and the list of

  3. Radioligand Recognition of Insecticide Targets.

    Science.gov (United States)

    Casida, John E

    2018-04-04

    Insecticide radioligands allow the direct recognition and analysis of the targets and mechanisms of toxic action critical to effective and safe pest control. These radioligands are either the insecticides themselves or analogs that bind at the same or coupled sites. Preferred radioligands and their targets, often in both insects and mammals, are trioxabicyclooctanes for the γ-aminobutyric acid (GABA) receptor, avermectin for the glutamate receptor, imidacloprid for the nicotinic receptor, ryanodine and chlorantraniliprole for the ryanodine receptor, and rotenone or pyridaben for NADH + ubiquinone oxidoreductase. Pyrethroids and other Na + channel modulator insecticides are generally poor radioligands due to lipophilicity and high nonspecific binding. For target site validation, the structure-activity relationships competing with the radioligand in the binding assays should be the same as that for insecticidal activity or toxicity except for rapidly detoxified or proinsecticide analogs. Once the radioligand assay is validated for relevance, it will often help define target site modifications on selection of resistant pest strains, selectivity between insects and mammals, and interaction with antidotes and other chemicals at modulator sites. Binding assays also serve for receptor isolation and photoaffinity labeling to characterize the interactions involved.

  4. Novel GABA receptor pesticide targets.

    Science.gov (United States)

    Casida, John E; Durkin, Kathleen A

    2015-06-01

    The γ-aminobutyric acid (GABA) receptor has four distinct but overlapping and coupled targets of pesticide action importantly associated with little or no cross-resistance. The target sites are differentiated by binding assays with specific radioligands, resistant strains, site-directed mutagenesis and molecular modeling. Three of the targets are for non-competitive antagonists (NCAs) or channel blockers of widely varied chemotypes. The target of the first generation (20th century) NCAs differs between the larger or elongated compounds (NCA-IA) including many important insecticides of the past (cyclodienes and polychlorocycloalkanes) or present (fiproles) and the smaller or compact compounds (NCA-IB) highly toxic to mammals and known as cage convulsants, rodenticides or chemical threat agents. The target of greatest current interest is designated NCA-II for the second generation (21st century) of NCAs consisting for now of isoxazolines and meta-diamides. This new and uniquely different NCA-II site apparently differs enough between insects and mammals to confer selective toxicity. The fourth target is the avermectin site (AVE) for allosteric modulators of the chloride channel. NCA pesticides vary in molecular surface area and solvent accessible volume relative to avermectin with NCA-IBs at 20-22%, NCA-IAs at 40-45% and NCA-IIs at 57-60%. The same type of relationship relative to ligand-docked length is 27-43% for NCA-IBs, 63-71% for NCA-IAs and 85-105% for NCA-IIs. The four targets are compared by molecular modeling for the Drosophila melanogaster GABA-R. The principal sites of interaction are proposed to be: pore V1' and A2' for NCA-IB compounds; pore A2', L6' and T9' for NCA-IA compounds; pore T9' to S15' in proximity to M1/M3 subunit interface (or alternatively an interstitial site) for NCA-II compounds; and M1/M3, M2 interfaces for AVE. Understanding the relationships of these four binding sites is important in resistance management and in the discovery and use

  5. Cellular Targets of Dietary Polyphenol Resveratrol

    National Research Council Canada - National Science Library

    Wu, Joseph M

    2006-01-01

    To test the hypothesis that resveratrol, a grape derived polyphenol, exerts its chemopreventive properties against prostate cancer by interacting with specific cellular targets, denoted resveratrol targeting proteins (RTPs...

  6. Exploiting target amplitude information to improve multi-target tracking

    Science.gov (United States)

    Ehrman, Lisa M.; Blair, W. Dale

    2006-05-01

    Closely-spaced (but resolved) targets pose a challenge for measurement-to-track data association algorithms. Since the Mahalanobis distances between measurements collected on closely-spaced targets and tracks are similar, several elements of the corresponding kinematic measurement-to-track cost matrix are also similar. Lacking any other information on which to base assignments, it is not surprising that data association algorithms make mistakes. One ad hoc approach for mitigating this problem is to multiply the kinematic measurement-to-track likelihoods by amplitude likelihoods. However, this can actually be detrimental to the measurement-to-track association process. With that in mind, this paper pursues a rigorous treatment of the hypothesis probabilities for kinematic measurements and features. Three simple scenarios are used to demonstrate the impact of basing data association decisions on these hypothesis probabilities for Rayleigh, fixed-amplitude, and Rician targets. The first scenario assumes that the tracker carries two tracks but only one measurement is collected. This provides insight into more complex scenarios in which there are fewer measurements than tracks. The second scenario includes two measurements and one track. This extends naturally to the case with more measurements than tracks. Two measurements and two tracks are present in the third scenario, which provides insight into the performance of this method when the number of measurements equals the number of tracks. In all cases, basing data association decisions on the hypothesis probabilities leads to good results.

  7. Tyrosine kinase inhibitors: Multi-targeted or single-targeted?

    Science.gov (United States)

    Broekman, Fleur; Giovannetti, Elisa; Peters, Godefridus J

    2011-02-10

    Since in most tumors multiple signaling pathways are involved, many of the inhibitors in clinical development are designed to affect a wide range of targeted kinases. The most important tyrosine kinase families in the development of tyrosine kinase inhibitors are the ABL, SCR, platelet derived growth factor, vascular endothelial growth factor receptor and epidermal growth factor receptor families. Both multi-kinase inhibitors and single-kinase inhibitors have advantages and disadvantages, which are related to potential resistance mechanisms, pharmacokinetics, selectivity and tumor environment. In different malignancies various tyrosine kinases are mutated or overexpressed and several resistance mechanisms exist. Pharmacokinetics is influenced by interindividual differences and differs for two single targeted inhibitors or between patients treated by the same tyrosine kinase inhibitor. Different tyrosine kinase inhibitors have various mechanisms to achieve selectivity, while differences in gene expression exist between tumor and stromal cells. Considering these aspects, one type of inhibitor can generally not be preferred above the other, but will depend on the specific genetic constitution of the patient and the tumor, allowing personalized therapy. The most effective way of cancer treatment by using tyrosine kinase inhibitors is to consider each patient/tumor individually and to determine the strategy that specifically targets the consequences of altered (epi)genetics of the tumor. This strategy might result in treatment by a single multi kinase inhibitor for one patient, but in treatment by a couple of single kinase inhibitors for other patients.

  8. Targeting an efficient target-to-target interval for P300 speller brain–computer interfaces

    Science.gov (United States)

    Sellers, Eric W.; Wang, Xingyu

    2013-01-01

    Longer target-to-target intervals (TTI) produce greater P300 event-related potential amplitude, which can increase brain–computer interface (BCI) classification accuracy and decrease the number of flashes needed for accurate character classification. However, longer TTIs requires more time for each trial, which will decrease the information transfer rate of BCI. In this paper, a P300 BCI using a 7 × 12 matrix explored new flash patterns (16-, 18- and 21-flash pattern) with different TTIs to assess the effects of TTI on P300 BCI performance. The new flash patterns were designed to minimize TTI, decrease repetition blindness, and examine the temporal relationship between each flash of a given stimulus by placing a minimum of one (16-flash pattern), two (18-flash pattern), or three (21-flash pattern) non-target flashes between each target flashes. Online results showed that the 16-flash pattern yielded the lowest classification accuracy among the three patterns. The results also showed that the 18-flash pattern provides a significantly higher information transfer rate (ITR) than the 21-flash pattern; both patterns provide high ITR and high accuracy for all subjects. PMID:22350331

  9. Transuranium Processing Plant semiannual report of production, status, and plans for period ending December 31, 1976

    International Nuclear Information System (INIS)

    King, L.J.; Bigelow, J.E.; Collins, E.D.

    1977-10-01

    During the period July 1, 1976, through December 31, 1976, transuranium elements were obtained from 11 irradiated HFIR targets; products recovered are 0.3 g 243 Am, 16.6 g 244 Cm, 23 g 249 Bk, 211 g 252 Cf, 1.15 mg 253 Es, and 0.4 pg 247 Fm. Two batches of high-purity 248 Cm were purified chemically for shipment, and another batch containing about 62 mg of 248 Cm was separated from 252 Cf. Thirty shipments were made from TRU during the period; recipients and the amounts of nuclides are listed in tabular form. Nine HFIR targets, each containing 8 to 9 g of curium, were fabricated. The sequence of chemical processing steps used to purify the californium product was changed; this change yielded a shorter recovery time for high-purity 253 Es, which enabled a 50% increase in the amount obtained. Eight neutron sources were fabricated during this report period, bringing the total fabricated to date to 92. Three sources that had previously been returned to TRU were reassigned; two others are also available for reassignment. The values currently being used for transuranium element decay data and for cross-section data in planning irradiation-processing cycles, calculating production forecasts, and assaying products are tabulated in the Appendix

  10. A blow-in windowless gas target

    International Nuclear Information System (INIS)

    Sagara, K.; Motoshima, A.; Fujita, T.; Akiyoshi, H.; Nishimori, N.

    1996-01-01

    A new-type windowless gas target has been developed to realize a dense target with a low gas flow rate. The target is similar to the conventional differentially pumped windowless gas target except that the target gas is blown into the target region from both the side holes of the beam entrance and exit. Due to the gas-confining action caused by the blown-in gas, the target thickness is about twice increased and the target density sharply falls in the holes. Most of the target gas is at rest and the density is uniform. The gas flow rate is the same as that of the conventional target and is about an order of magnitude lower than that of the dense gas-jet target. (orig.)

  11. Tritium target manufacturing for use in accelerators

    Science.gov (United States)

    Bach, P.; Monnin, C.; Van Rompay, M.; Ballanger, A.

    2001-07-01

    As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium target on copper substrate, and going to more sophisticated devices. A wide range of possible uses is covered, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets for higher lifetimes, or large size rotating targets for accelerators used in boron neutron therapy. Activity of targets lies in the 1 to 1000 Curie, diameter of targets being up to 30 cm. Special targets are also considered, including surface layer targets for lowering tritium desorption under irradiation, or those made from different kinds of occluders such as titanium, zirconium, erbium, scandium, with different substrates. It is then possible to optimize either neutron output, or lifetime and stability, or thermal behavior.

  12. Cryogenic polarized target facility: status

    International Nuclear Information System (INIS)

    Gould, C.; Nash, H.K.; Roberson, N.; Schneider, M.; Seagondollar, W.; Soderstrum, J.

    1985-01-01

    The TUNL cryogenically polarized target facility consists of a 3 He- 4 He dilution refrigerator and a superconducting magnet, together capable of maintaining samples at between 10 and 20 mK in magnetic fields up to 7 Tesla. At these temperatures and magnetic fields brute-force nuclear orientation occurs. Polarizations from 20 to 60% are attainable in about twenty nonzero spin nuclei. Most are metals, ranging in mass from 6 Li to 209 Bi, but the nuclei 1 H and 3 He are also polarizable via this method. The main effort is directed towards a better determination of the effective spin-spin force in nuclei. These experiments are briefly described and the beam stabilization system, cryostat and polarized 3 He targets are discussed

  13. Downstream targets of WRKY33

    DEFF Research Database (Denmark)

    Petersen, Klaus; Fiil, Berthe Katrine; Mundy, John

    2008-01-01

    Innate immunity signaling pathways in both animals and plants are regulated by mitogen-activated protein kinase (MAPK) cascades. In a recent publication we show that MPK4 and its substrate MKS1 interact with WRKY33 in vivo, and that WRKY33 is released from complexes with MPK4 upon infection....... Transcriptome analysis of a wrky33 loss-of-function mutant identified a subset of defense-related genes as putative targets of WRKY33. These genes include PAD3 and CYP71A13, which encode cytochrome P450 monoxygenases required for synthesis of the antimicrobial phytoalexin camalexin. Chromatin...... immunoprecipitation confirmed that WRKY33 bound the promoter of PAD3 when plants were inoculated with pathogens. Here we further discuss the involvement of two other targets of WRKY33, NUDT6 and ROF2 in defense responses against invading pathogens....

  14. Targeted Learning in Healthcare Research.

    Science.gov (United States)

    Gruber, Susan

    2015-12-01

    The increasing availability of Big Data in healthcare encourages investigators to seek answers to big questions. However, nonparametric approaches to analyzing these data can suffer from the curse of dimensionality, and traditional parametric modeling does not necessarily scale. Targeted learning (TL) combines semiparametric methodology with advanced machine learning techniques to provide a sound foundation for extracting information from data. Predictive models, variable importance measures, and treatment benefits and risks can all be addressed within this framework. TL has been applied in a broad range of healthcare settings, including genomics, precision medicine, health policy, and drug safety. This article provides an introduction to the two main components of TL, targeted minimum loss-based estimation and super learning, and gives examples of applications in predictive modeling, variable importance ranking, and comparative effectiveness research.

  15. Targeting Wnt Pathways in Disease

    Science.gov (United States)

    Zimmerman, Zachary F.; Moon, Randall T.

    2012-01-01

    Wnt-mediated signal transduction pathways have long been recognized for their roles in regulating embryonic development, and have more recently been linked to cancer, neurologic diseases, inflammatory diseases, and disorders of endocrine function and bone metabolism in adults. Although therapies targeting Wnt signaling are attractive in theory, in practice it has been difficult to obtain specific therapeutics because many components of Wnt signaling pathways are also involved in other cellular processes, thereby reducing the specificity of candidate therapeutics. New technologies, and advances in understanding the mechanisms of Wnt signaling, have improved our understanding of the nuances of Wnt signaling and are leading to promising new strategies to target Wnt signaling pathways. PMID:23001988

  16. Voyager 2 Uranus targeting strategy

    Science.gov (United States)

    Cesarone, R. J.; Gray, D. L.; Potts, C. L.; Francis, K.

    1986-01-01

    One of the major challenges involved in the Voyager 2 Uranus flyby is to deliver the spacecraft to an appropriate aimpoint at the optimum time, so as to maximize the science return of the mission, while yet keeping propellant expenditure low. An unusual targeting strategy has been devised to satisfy these requirements. Its complexity arises from the great distance of the planet Uranus and the limited performance capabilities of Voyager. This selected strategy is developed in relation to a set of candidate strategies, mission requirements and shifting science objectives. The analysis of these candidates is conducted via a Monte Carlo simulation, the results of which yield data for the comparative evaluation and eventual and selection of the actual targeting strategy to be employed.

  17. Jet target intense neutron source

    International Nuclear Information System (INIS)

    Meier, K.L.

    1977-01-01

    A jet target Intense Neutron Source (INS) is being built by the Los Alamos Scientific Laboratory with DOE/MFE funding in order to perform radiation damage experiments on materials to be used in fusion power reactors. The jet target can be either a supersonic or a subsonic jet. Each type has its particular advantages and disadvantages, and either of the jets can be placed inside the spherical blanket converter which will be used to simulate a fusion reactor neutron environment. Preliminary mock-up experiments with a 16-mA, 115 keV, H + ion beam on a nitrogen gas supersonic jet show no serious problems in the beam formation, transport, or jet interaction

  18. Recurring Utterances - Targeting a Breakthrough

    Directory of Open Access Journals (Sweden)

    Jacqueline Stark

    2014-05-01

    The most interesting phenomenon is KB’s production of words from former sessions indicating that they are still ‘active’ and the production of completely novel incorrect words. The observable features indicate that immediate auditory processing is possible in the form of repeating target words. However, as soon as KB must retrieve information from the (semantic lexicon, even after being able to correctly ‘repeat’ the target word several times, he responds with a RU, perseveration, or paraphasia. Several of his productions can be characterized as aphasic confabulations which stem from a memory gap. Thus, although KB’s language impairment is severe, his responses across time indicate that step-by-step a breakthrough is being made.

  19. Super liquid density target designs

    International Nuclear Information System (INIS)

    Pan, Y.L.; Bailey, D.S.

    1976-01-01

    The success of laser fusion depends on obtaining near isentropic compression of fuel to very high densities and igniting this fuel. To date, the results of laser fusion experiments have been based mainly on the exploding pusher implosion of fusion capsules consisting of thin glass microballoons (wall thickness of less than 1 micron) filled with low density DT gas (initial density of a few mg/cc). Maximum DT densities of a few tenths of g/cc and temperatures of a few keV have been achieved in these experiments. We will discuss the results of LASNEX target design calculations for targets which: (a) can compress fuel to much higher densities using the capabilities of existing Nd-glass systems at LLL; (b) allow experimental measurement of the peak fuel density achieved

  20. Swimbladder on Fish Target Strength

    Directory of Open Access Journals (Sweden)

    Sunardi

    2008-08-01

    Full Text Available This paper discusses of target strength (TS for the Selar boops (Oxeye scad and Megalaspis cordyla (Torpedo scad, the most commercially fish in Malaysia. TS can be determined from in situ measurements and acoustic calculation of fish model. TS value, depth, and position (x-y-z of targeted fish can be viewed from echogram using FQ-80 Analyzer by in situ measurement. X-ray imaged can be deployed to develop the acoustic fish model. The percentage of length and upper surface area for swimbladder to body fish of Selar boops more than Megalaspis cordyla can be measured after X-ray process. The percentage of width and volume of swimbladders to its each body are no significantly difference for both fish. These data of swimbladder physic support the result of in situ measurement which TS of Megalaspis cordyla stronger Selar boops.

  1. CATAMARAN targeted at innovative radiopharmacy

    International Nuclear Information System (INIS)

    Impens, N.; Aerts, A.

    2010-01-01

    In cancer therapy there is a great need for specific treatments: therapies that kill cancer cells selectively without affecting the healthy cells. In the CATAMARAN project (Cancer Targeting Molecules Attached to Radionuclides) SCK-CEN develops, in a preclinical trial, products that deliver the right radiation doses at the right place in the human body. With the new multidisciplinary expertise that has been built up in the project, SCK-CEN is contributing to new medical applications of radiation.

  2. Targeted advertising in magazine markets

    OpenAIRE

    Chandra, Ambarish; Kaiser, Ulrich

    2010-01-01

    We examine the scope and value of targeted advertising in the magazine industry. We use data on reader characteristics at individual media, in contrast to previous work that has needed to infer this information from aggregate data. Our results show a strong relationship between subscriber characteristics and advertising prices. Advertisers clearly value more homogenous groups of readers, measured according to income, gender and age. Our results explain recent trends of declining advertising e...

  3. Peptide-targeted polymer cancerostatics

    Czech Academy of Sciences Publication Activity Database

    Böhmová, Eliška; Pola, Robert

    2016-01-01

    Roč. 65, Suppl. 2 (2016), S153-S164 ISSN 0862-8408 R&D Projects: GA MŠk(CZ) LO1507 Institutional support: RVO:61389013 Keywords : HPMA copolymers * tumor targeting * peptides Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.461, year: 2016 http://www.biomed.cas.cz/physiolres/pdf/65%20Suppl%202/65_S153.pdf

  4. Target Advertising and Market Transparency

    OpenAIRE

    Stühmeier, Torben

    2012-01-01

    This paper examines the effects of increased transparency over online news sources, e.g. due to news aggregators, on online news outlets and the advertising industry. The role of news aggregators is controversially discussed, where the discussion widely points on user side effect. The present paper widens the discussion on the advertising side and shows that aggregators can help to better target advertising messages to a more homogenous group of users and, in turn, may both benefit advertiser...

  5. Targeting phenotypically tolerant Mycobacterium tuberculosis

    Science.gov (United States)

    Gold, Ben; Nathan, Carl

    2016-01-01

    While the immune system is credited with averting tuberculosis in billions of individuals exposed to Mycobacterium tuberculosis, the immune system is also culpable for tempering the ability of antibiotics to deliver swift and durable cure of disease. In individuals afflicted with tuberculosis, host immunity produces diverse microenvironmental niches that support suboptimal growth, or complete growth arrest, of M. tuberculosis. The physiological state of nonreplication in bacteria is associated with phenotypic drug tolerance. Many of these host microenvironments, when modeled in vitro by carbon starvation, complete nutrient starvation, stationary phase, acidic pH, reactive nitrogen intermediates, hypoxia, biofilms, and withholding streptomycin from the streptomycin-addicted strain SS18b, render M. tuberculosis profoundly tolerant to many of the antibiotics that are given to tuberculosis patients in a clinical setting. Targeting nonreplicating persisters is anticipated to reduce the duration of antibiotic treatment and rate of post-treatment relapse. Some promising drugs to treat tuberculosis, such as rifampicin and bedaquiline, only kill nonreplicating M. tuberculosis in vitro at concentrations far greater than their minimal inhibitory concentrations against replicating bacilli. There is an urgent demand to identify which of the currently used antibiotics, and which of the molecules in academic and corporate screening collections, have potent bactericidal action on nonreplicating M. tuberculosis. With this goal, we review methods of high throughput screening to target nonreplicating M. tuberculosis and methods to progress candidate molecules. A classification based on structures and putative targets of molecules that have been reported to kill nonreplicating M. tuberculosis revealed a rich diversity in pharmacophores. However, few of these compounds were tested under conditions that would exclude the impact of adsorbed compound acting during the recovery phase of

  6. Targeting ECM Disrupts Cancer Progression

    DEFF Research Database (Denmark)

    Venning, Freja A; Wullkopf, Lena; Erler, Janine T

    2015-01-01

    , the extracellular matrix (ECM). Many ECM proteins are significantly deregulated during the progression of cancer, causing both biochemical and biomechanical changes that together promote the metastatic cascade. In this review, the influence of several ECM proteins on these multiple steps of cancer spread...... is summarized. In addition, we highlight the promising (pre-)clinical data showing benefits of targeting these ECM macromolecules to prevent cancer progression....

  7. Fixed target flammable gas upgrades

    International Nuclear Information System (INIS)

    Schmitt, R.; Squires, B.; Gasteyer, T.; Richardson, R.

    1996-12-01

    In the past, fixed target flammable gas systems were not supported in an organized fashion. The Research Division, Mechanical Support Department began to support these gas systems for the 1995 run. This technical memo describes the new approach being used to supply chamber gasses to fixed target experiments at Fermilab. It describes the engineering design features, system safety, system documentation and performance results. Gas mixtures provide the medium for electron detection in proportional and drift chambers. Usually a mixture of a noble gas and a polyatomic quenching gas is used. Sometimes a small amount of electronegative gas is added as well. The mixture required is a function of the specific chamber design, including working voltage, gain requirements, high rate capability, aging and others. For the 1995 fixed target run all the experiments requested once through gas systems. We obtained a summary of problems from the 1990 fixed target run and made a summary of the operations logbook entries from the 1991 run. These summaries primarily include problems involving flammable gas alarms, but also include incidents where Operations was involved or informed. Usually contamination issues were dealt with by the experimenters. The summaries are attached. We discussed past operational issues with the experimenters involved. There were numerous incidents of drift chamber failure where contaminated gas was suspect. However analyses of the gas at the time usually did not show any particular problems. This could have been because the analysis did not look for the troublesome component, the contaminant was concentrated in the gas over the liquid and vented before the sample was taken, or that contaminants were drawn into the chambers directly through leaks or sub-atmospheric pressures. After some study we were unable to determine specific causes of past contamination problems, although in argon-ethane systems the problems were due to the ethane only

  8. Therapeutic targets in liver fibrosis.

    Science.gov (United States)

    Fallowfield, Jonathan A

    2011-05-01

    Detailed analysis of the cellular and molecular mechanisms that mediate liver fibrosis has provided a framework for therapeutic approaches to prevent, slow down, or even reverse fibrosis and cirrhosis. A pivotal event in the development of liver fibrosis is the activation of quiescent hepatic stellate cells (HSCs) to scar-forming myofibroblast-like cells. Consequently, HSCs and the factors that regulate HSC activation, proliferation, and function represent important antifibrotic targets. Drugs currently licensed in the US and Europe for other indications target HSC-related components of the fibrotic cascade. Their deployment in the near future looks likely. Ultimately, treatment strategies for liver fibrosis may vary on an individual basis according to etiology, risk of fibrosis progression, and the prevailing pathogenic milieu, meaning that a multiagent approach could be required. The field continues to develop rapidly and starts to identify exciting potential targets in proof-of-concept preclinical studies. Despite this, no antifibrotics are currently licensed for use in humans. With epidemiological predictions for the future prevalence of viral, obesity-related, and alcohol-related cirrhosis painting an increasingly gloomy picture, and a shortfall in donors for liver transplantation, the clinical urgency for new therapies is high. There is growing interest from stakeholders keen to exploit the market potential for antifibrotics. However, the design of future trials for agents in the developmental pipeline will depend on strategies that enable equal patient stratification, techniques to reliably monitor changes in fibrosis over time, and the definition of clinically meaningful end points.

  9. Fixed Target Collisions at STAR

    Energy Technology Data Exchange (ETDEWEB)

    Meehan, Kathryn C.

    2016-12-15

    The RHIC Beam Energy Scan (BES) program was proposed to look for the turn-off of signatures of the quark gluon plasma (QGP), search for a possible QCD critical point, and study the nature of the phase transition between hadronic and partonic matter. Previous results have been used to claim that the onset of deconfinement occurs at a center-of-mass energy of 7 GeV. Data from lower energies are needed to test if this onset occurs. The goal of the STAR Fixed-Target Program is to extend the collision energy range in BES II to energies that are likely below the onset of deconfinement. Currently, STAR has inserted a gold target into the beam pipe and conducted test runs at center-of-mass energies of 3.9 and 4.5 GeV. Tests have been done with both Au and Al beams. First physics results from a Coulomb potential analysis of Au + Au fixed-target collisions are presented and are found to be consistent with results from previous experiments. Furthermore, the Coulomb potential, which is sensitive to the Z of the projectile and degree of baryonic stopping, will be compared to published results from the AGS.

  10. Treat to target in gout.

    Science.gov (United States)

    Perez-Ruiz, Fernando; Moreno-Lledó, Aitana; Urionagüena, Irati; Dickson, Alastair J

    2018-01-01

    The treat-to-target (T2T) approach has been successfully implemented in a number of diseases. T2T has been proposed for rheumatic diseases such as RA, spondyloarthritis, lupus, and recently for gout. The level of evidence for such approaches differs from one condition to the other (moderate to high for hyperlipidaemia, for example). Practice is based on the best available evidence at any time, and in absence of good evidence for T2T in gout, some suggest a conservative only-treat-symptoms approach. Evidence suggests that not treating gout to target in the long term is overall associated with worsening outcomes, such as flares, tophi and structural damage, which is associated to loss of quality of life and mortality. Different targets have been proposed for hyperuricaemia in gout; lower than 6 mg/dl (0.36 mmol/l) for all patients, at least gout. © The Author 2018. Published by Oxford University Press on behalf of the British Society for Rheumatology. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  11. A cryogenic infrared calibration target

    Science.gov (United States)

    Wollack, E. J.; Kinzer, R. E.; Rinehart, S. A.

    2014-04-01

    A compact cryogenic calibration target is presented that has a peak diffuse reflectance, R ⩽ 0.003, from 800 to 4800 cm-1 (12 - 2 μm). Upon expanding the spectral range under consideration to 400-10 000 cm-1 (25 - 1 μm) the observed performance gracefully degrades to R ⩽ 0.02 at the band edges. In the implementation described, a high-thermal-conductivity metallic substrate is textured with a pyramidal tiling and subsequently coated with a thin lossy dielectric coating that enables high absorption and thermal uniformity across the target. The resulting target assembly is lightweight, has a low-geometric profile, and has survived repeated thermal cycling from room temperature to ˜4 K. Basic design considerations, governing equations, and test data for realizing the structure described are provided. The optical properties of selected absorptive materials—Acktar Fractal Black, Aeroglaze Z306, and Stycast 2850 FT epoxy loaded with stainless steel powder—are characterized and presented.

  12. Targeting the Brain with Nanomedicine.

    Science.gov (United States)

    Rueda, Felix; Cruz, Luis J

    2017-01-01

    Herein, we review innovative nanomedicine-based approaches for treating, preventing and diagnosing neurodegenerative diseases. We focus on nanoscale systems such as polymeric nanoparticles (NPs), liposomes, micelles and other vehicles (e.g. dendrimers, nanogels, nanoemulsions and nanosuspensions) for targeted delivery of bioactive molecules to the brain. To ensure maximum selectivity for optimal therapeutic or diagnostic results, researchers must employ delivery systems that are non-toxic, biodegradable and biocompatible. This entails: (i) use of "safe" materials, such as polymers or lipids; (ii) targeting to the brain and, specifically, to the desired active site within the brain; (iii) controlled release of the loaded agent; and (iv) use of agents that, once released into the brain, will exhibit the desired pharmacologic activity. Here, we explore the design and preclinical use of representative delivery systems that have been proposed to date. We then analyze the principal challenges that have delayed clinical application of these and other approaches. Lastly, we look at future developments in this area, addressing the needs for increased penetration of the blood brain barrier (BBB), enhanced targeting of specific brain sites, improved therapeutic efficacy and lower neurotoxicity. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  13. Fixed-Target Electron Accelerators

    International Nuclear Information System (INIS)

    Brooks, William K.

    2001-01-01

    A tremendous amount of scientific insight has been garnered over the past half-century by using particle accelerators to study physical systems of sub-atomic dimensions. These giant instruments begin with particles at rest, then greatly increase their energy of motion, forming a narrow trajectory or beam of particles. In fixed-target accelerators, the particle beam impacts upon a stationary sample or target which contains or produces the sub-atomic system being studied. This is in distinction to colliders, where two beams are produced and are steered into each other so that their constituent particles can collide. The acceleration process always relies on the particle being accelerated having an electric charge; however, both the details of producing the beam and the classes of scientific investigations possible vary widely with the specific type of particle being accelerated. This article discusses fixed-target accelerators which produce beams of electrons, the lightest charged particle. As detailed in the report, the beam energy has a close connection with the size of the physical system studied. Here a useful unit of energy is a GeV, i.e., a giga electron-volt. (ne GeV, the energy an electron would have if accelerated through a billion volts, is equal to 1.6 x 10 -10 joules.) To study systems on a distance scale much smaller than an atomic nucleus requires beam energies ranging from a few GeV up to hundreds of GeV and more

  14. Rapid selective separation of americium/curium from simulated nuclear forensic matrices using triazine ligands

    Energy Technology Data Exchange (ETDEWEB)

    Higginson, Matthew A.; Livens, Francis R.; Heath, Sarah L. [Manchester Univ. (United Kingdom). Centre for Radiochemistry Research; Thompson, Paul; Marsden, Olivia J. [AWE, Aldermaston, Reading (United Kingdom); Harwood, Laurence M.; Hudson, Michael J. [Reading Univ. (United Kingdom). Dept. of Chemistry; Lewis, Frank W. [Reading Univ. (United Kingdom). Dept. of Chemistry; Northumbria Univ., Newcastle upon Tyne (United Kingdom). Dept. of Chemical and Forensic Sciences

    2015-07-01

    In analysis of complex nuclear forensic samples containing lanthanides, actinides and matrix elements, rapid selective extraction of Am/Cm for quantification is challenging, in particular due the difficult separation of Am/Cm from lanthanides. Here we present a separation process for Am/Cm(III) which is achieved using a combination of AG1-X8 chromatography followed by Am/Cm extraction with a triazine ligand. The ligands tested in our process were CyMe{sub 4}-BTPhen, CyMe{sub 4}-BTBP, CA-BTP and CA-BTPhen. Our process allows for purification and quantification of Am and Cm (recoveries 80% - 100%) and other major actinides in < 2 d without the use of multiple columns or thiocyanate. The process is unaffected by high level Ca(II)/Fe(III)/Al(III) (10 mg mL{sup -1}) and thus requires little pre-treatment of samples.

  15. Uptake of plutonium, americium, curium, and neptunium in plants cultivated under greenhouse conditions

    International Nuclear Information System (INIS)

    Pimpl, M.; Schmidt, W.

    1984-01-01

    The root-uptake of Np, Pu, Am, and Cm from three different artificially contaminated soils in grass, maize, spring wheat, and potatoes was investigated under greenhouse conditions in pots filled with 9 kg contaminated soil and in lysimeters with a surface area of 0,5 m 2 containing the soils in undisturbed profils up to a depth of 80 cm. Only the plough layer of 30 cm was contaminated with Np, Pu, Am, and Cm. Crop cultivation was done corresponding to usual practice in agriculture. Results of the 1st vegetation period are represented. Transfer factors obtained deviate considerably from those which are recommended for the estimation of long-term exposure of man in the Federal Republic of Germany. (orig.)

  16. Fission-product yields for thermal-neutron fission of curium-243

    International Nuclear Information System (INIS)

    Breederland, D.G.

    1982-01-01

    Cumulative fission yields for 25 gamma rays emitted during the decay of 23 fission products produced by thermal-neutron fission of 243 Cm have been determined. Using Ge(Li) spectroscopy, 33 successive pulse-height spectra of gamma rays emitted from a 77-ng sample of 243 Cm over a period of approximately two and one-half months were analyzed. Reduction of these spectra resulted in the identification and matching of gamma-ray energies and half-lives to specific radionuclides. Using these results, 23 cumulative fission-product yields were calculated. Only those radionuclides having half-lives between 6 hours and 65 days were observed. Prior to this experiment, no fission-product yields had been recorded for 243 Cm

  17. Characteristics of plutonium, curium and uranium in hulls of FUGEN MOX spent fuel by destructive analysis

    International Nuclear Information System (INIS)

    Iijima, Shizuka; Goto, Yuichi; Samoto, Hirotaka; Shichi, Ryo; Shimizu, Takenori

    2011-01-01

    We have been developing a non-destructive assay system called hulls monitor for nuclear fuel materials retained in hulls at the Tokai Reprocessing Plant (TRP). The hulls monitor is based on a passive neutron measurement method, so its applicability should be evaluated by a destructive analysis of hulls that are recovered from the reprocessing process. In this study, hulls came from the Advanced Thermal Reactor (ATR) FUGEN were taken from the dissolution process of TRP and destructively analyzed. Two kinds of hulls from ATR-MOX spent fuel assemblies and from ATR-UO 2 spent fuel assemblies were taken and soaked with nitric acid then fused with ammonium hydrogen sulfate, followed by Pu, 244 Cm, U mass determination by alpha spectrometry and ICP-AES. The characteristics of hulls came from MOX spent fuel assemblies were revealed by comparison of ATR-MOX spent fuel with ATR-UO 2 spent fuel. (author)

  18. Americium-Curium Stabilization - 5'' Cylindrical Induction Melter System Design Basis

    International Nuclear Information System (INIS)

    Witt, D.C.

    1999-01-01

    Approximately 11,000 liters (3,600) gallons of solution containing isotopes of Am and Cm are currently stored in F-Canyon Tank 17.1. These isotopes were recovered during plutonium-242 production campaigns in the mid- and late-1970s. Experimental work for the project began in 1995 by the Savannah River Technology Center (SRTC). Details of the process are given in the various sections of this document

  19. Optimization conditions for the separation of rare earth elements, americium, curium and cesium with HPLC technique

    International Nuclear Information System (INIS)

    Goutelard, F.; Caussignac, C.; Brennetot, R.; Stadelmann, G.; Gautier, C.

    2009-01-01

    In order to validate the neutronic code calculations used in the nuclear field, it is necessary to quantify the isotopic composition of the nuclear irradiated fuels with high precision and accuracy. A separation step whose objective is to isolate the elements of interest in a fraction as pure as possible, is performed before mass spectrometry detection (MC-ICP-MS, TIMS), in order to eliminate isobaric interferences. In a first step, uranium and plutonium are separated from the fission products by ion exchange chromatography. Then, fission products are separated by high performance liquid chromatography (HPLC). A gradient separation with a silica sulphonated support as stationary phase and hydroxy-methyl butyric acid (HMB) as eluent solution provides a good degree of separation of the rare earth elements, Am, Cm and Cs. But, for a same manufacturer, the rate of sulphonated groups is variable from one column to another for a given production batch. For every replacement of column, it is necessary to adjust the separation conditions. Furthermore, the high radioactivity of the samples injected damages the stationary phase, dragging a regular renewal of the columns. The goal of this study is to determine the optimal separation conditions with a minimum of tests in order to limit the time assigned to this operation. A first Doehlert experimental design with pH and HMB concentration as variables has been implemented to optimize Gd, Eu separation, in isocratic initial conditions. A second one has been tested in order to separate the higher lanthanides and to fix the final conditions of the gradient separation. A last set of tests has been performed to characterize the cesium behaviour. Finally, the gradient conditions have been adjusted in order to perform the full separation of lanthanides, Cs, Am and Cm with nuclear facilities. (author)

  20. Temperature thresholds for surface blistering of platinum and stainless steel exposed to curium-242 alpha radiations

    International Nuclear Information System (INIS)

    McDonell, W.R.; Dillich, S.

    1981-01-01

    Implantation of helium in materials exposed to alpha-emitting radionuclides such as 242 Cm causes surface blistering at elevated temperatures. The temperature thresholds for such blistering are of practical importance to the selection of suitable container materials for radionuclides, and are of fundamental interest with regard to the mechanisms of helium blistering of materials in radiation environments. The purpose of this investigation was to establish temperature thresholds for surface blistering of platinum and stainless-steel container materials by post-irradiation heating of specimens exposed at room temperature to alpha particles from an external 242 Cm source. These thresholds were compared with (1) the analogous temperature thresholds for surface blistering of materials exposed to external beams of accelerator helium ions, and (2) thresholds for swelling and grain-boundary cracking of materials in which helium is generated internally by (n,α) reactions during reactor exposures

  1. Multi-recycling of plutonium and incineration of americium, curium, and technetium in PWRs

    International Nuclear Information System (INIS)

    Golfier, H.; Bergeron, J.; Puill, A.; Rohart, M.

    2000-01-01

    The future of nuclear power requires a clear strategy for radwaste and Plutonium management. Pressurized water reactors (PWR) and the associated fuel cycle installations represent the largest part of the French power plants (and are partly paid off). The reactors in service produce an annual 10 tons of Pu, 1.4 tons of minor actinides (MA), and 3.8 tons of long-lived fission products (LLFP). The spent fuel is reprocessed in La Hague plant to recover the energetic elements U and Pu. The latter was initially dedicated to power Fast Breeder Reactors that converted the depleted and reprocessed, thus ensuring a significant part of the French national energy resources. The shut-down of Super-Phenix, the postponement of building of Fast Breeder Reactors (FBR) and the relaxed need for stretching natural U resources raise the issue of Pu management. In fact, the Pu mono-recycling practiced in France since 1987 (St Laurent B1) only slows down the Pu accumulation in spent nuclear fuel, yet it is unable to stabilize the Pu inventory. Beyond the cooperation with its industrial partners, CEA investigates solutions for short and medium term Pu management thus contributing to research required for keeping nuclear power as an energy option. The range of these investigations shall cover both adaptations for light water reactors to facilitate Pu recycling and more innovative solutions concerning reactors, fuel and fuel cycle. The aim of using Pu more efficiently in PWR has led, not only for economic and non-proliferation reasons, but also for considerations related to the optimization of Pu and MA management. The mastery of Pu inventory is a requirement for all long-lived radwaste management methods. In this context, the potential of innovative PWRs has been investigated to control the Pu fluxes and to make them a milestone on the way to clean nuclear power. This paper presents the most recent results related to Pu utilization and MA and LLFP incineration like (Am+Cm) and Tc. To determine the influence of the Pu fluxes, a 1450 MWe PWR with one standard and one innovative concept (code named APA for Advanced Plutonium fuel Assembly) have been performed. A multi-recycling scenario is simulated with a 400 TWhe power plant park. (authors)

  2. Sorption of plutonium and curium on ion exchange resins in mixed aqueous organic solutions

    International Nuclear Information System (INIS)

    Haidvogel, N.; Reitsamer, G.; Grass, F.

    1974-12-01

    The sorption of the sulfate and nitrate-complexes of the actinides Pu(III), Pu(IV), Pu(VI), Am(III) and Om(III) on the ion-exchange-resins Dowex 1X8 and Dowex 50 WX8 is investigated. The strong sorbability of these actinide ions in solvents with high content of alcohol is explained by the existence of anionic complexes like Pu(III) (SO 4 ) 2 - , Pu(IV) (SO 4 ) 3 2 - , Pu(VI)O 2 (SO 4 ) 2 2 - , Am(SO 4 ) 2 - respectively Am(NO 3 ) 4 - and Om(NO 3 ) 4 - . The taking of autoradiographs from the thin-layer chromatograms by the aid of a special device and the evaluation of the autoradiographs by a particular photodensitometer are described. The measurement of the radioactivity of the α-emitting nuclides Pu 239, Am 241 and Om 242 are done by liquid-scintillation spectrometry. (author)

  3. Incorporation of plutonium, americium and curium into the Irish Sea seabed by biological activity

    Energy Technology Data Exchange (ETDEWEB)

    Kershaw, P J; Swift, D J; Pentreath, R J; Lovett, M B

    1984-12-01

    Bioturbation was considered as a potentially significant mechanism for the incorporation of long-lived radionuclides into the seabed and in particular the activities of a large echiuran Maximulleria lankesteri. Radionuclides of the transuranium elements plutonium, americium and cirium are discharged into the Irish Sea under authorization as part of the low-level liquid effluent from the British Nuclear Fuels plc reprocessing plant at Sellafield, Cumbria, England. The distribution of Pu-239, 240, Pu-238, Am-241, Cm-244 and Cm-242 concentrations and the Pu-239, 240/Pu-238 quotient in samples taken in April and May 1983 from the sediment surface, burrow linings, sediments adjacent to burrows, and the gut contents and body of a large M. lankesteri clearly indicate that bioturbation is responsible, at least in part, for the incorporation of these radionuclides to depths of up to 140 cm. This area of sediments represents a significant present-day sink, but the permanence of this sink and the likelihood that radioactivity will be remobilized and be returned to man, depends on a large number of factors. 15 references, 18 figures.

  4. Structural, electronic, and thermodynamic properties of curium dioxide: Density functional theory calculations

    Science.gov (United States)

    Hou, Ling; Li, Wei-Dong; Wang, Fangwei; Eriksson, Olle; Wang, Bao-Tian

    2017-12-01

    We present a systematic investigation of the structural, magnetic, electronic, mechanical, and thermodynamic properties of CmO2 with the local density approximation (LDA)+U and the generalized gradient approximation (GGA)+U approaches. The strong Coulomb repulsion and the spin-orbit coupling (SOC) effects on the lattice structures, electronic density of states, and band gaps are carefully studied, and compared with other A O2 (A =U , Np, Pu, and Am). The ferromagnetic configuration with half-metallic character is predicted to be energetically stable while a charge-transfer semiconductor is predicted for the antiferromagnetic configuration. The elastic constants and phonon spectra show that the fluorite structure is mechanically and dynamically stable. Based on the first-principles phonon density of states, the lattice vibrational energy is calculated using the quasiharmonic approximation. Then, the Gibbs free energy, thermal expansion coefficient, specific heat, and entropy are obtained and compared with experimental data. The mode Grüneisen parameters are presented to analyze the anharmonic properties. The Slack relation is applied to obtain the lattice thermal conductivity in temperature range of 300-1600 K. The phonon group velocities are also calculated to investigate the heat transfer. For all these properties, if available, we compare the results of CmO2 with other A O2 .

  5. Comparative uptake and distribution of plutonium, americium, curium and neptunium in four plant species

    Energy Technology Data Exchange (ETDEWEB)

    Schreckhise, R E; Cline, J F [Battelle Pacific Northwest Labs., Richland, WA (USA)

    1980-05-01

    Uptake of the nitrate forms of /sup 238/Pu, /sup 239/Pu, /sup 241/Am, /sup 244/Cm and /sup 237/Np from soil into selected parts of four different plant species grown under field conditions was compared Alfalfa, barley, peas and cheatgrass were grown outdoors in small weighing lysimeters filled with soil containing these radionuclides. The plants were harvested at maturity, divided into selected components and radiochemically analyzed by alpha-energy analysis. Soil concentration did not appear to affect the plant uptake of /sup 238/Pu, /sup 239/Pu, /sup 241/Am or /sup 244/Cm for the two levels utilized. The relative plant uptake of the five different transuranics was /sup 237/Np>/sup 244/Cm approximately equal /sup 241/Am>/sup 239/Pu approximately equal/sup 238/Pu. Relative uptake values of Np for various plant parts ranged from 2200 to 45,000 times as great as for Pu, while Am and Cm values were 10-20 times as great. The values for seeds were significantly lower than those for the other aboveground plant parts for all four transuranic elements. The legumes accumulated approx. 10 times more than the grasses. A comparison of the postulated radionuclide content of plants grown in soil contaminated with material from spent liquid metal fast breeder reactor fuels indicated that concentrations of isotopes of Am, Cm and Np would exceed /sup 239/Pu values.

  6. Assessment of Neptunium, Americium, and Curium in the Savannah River Site Environment

    International Nuclear Information System (INIS)

    Carlton, W.H.

    1997-01-01

    A series of documents has been published in which the impact of various radionuclides released to the environment by Savannah River Site (SRS) operations has been assessed. The quantity released, the disposition of the radionuclides in the environment, and the dose to offsite individuals has been presented for activation products, carbon cesium, iodine, plutonium, selected fission products, strontium, technetium, tritium, uranium, and the noble gases. An assessment of the impact of nonradioactive mercury also has been published.This document assesses the impact of radioactive transuranics released from SRS facilities since the first reactor became operational late in 1953. The isotopes reported here are 239Np, 241Am, and 244Cm

  7. Americium-curium separation by means of selective extraction of hexavalent americium using a centrifugal contactor

    International Nuclear Information System (INIS)

    Musikas, C.; Germain, M.; Bathellier, A.

    1979-01-01

    This paper deals with Am (VI) - Cm (III) separation in nitrate media. The kinetics of oxidation of Am (III) by sodium persulfate in the presence of Ag + ions were reinvestigated by studying the effect of additions of small amounts of reagents which do not drastically change the distribution coefficients of Am (VI) or Cm (III) ions. Organo phosphorus solvents were selected because they are radiation resistant, possess weak reductant properties and that their affinity for hexavalent ion is high. The operating procedure was selected by consideration of the results of the two previous investigations. This can be done by using a centrifugal contactor enabling in to set organic-aqueous phase contact time in accordance with the kinetics of extraction of Am (VI), oxidation of Am (III) in aqueous phase, and reduction of Am (VI) in organic phase

  8. Internal magnetic target of proton synchrotron

    International Nuclear Information System (INIS)

    Gachurin, V.V.; Kats, M.M.; Kondrat'ev, L.N.; Rogal', A.D.; Rusinov, V.Yu.

    1988-01-01

    Proton extraction from a synchrotron by means of an internal target of magnetized iron is described. The particles that are aimed at the target pass directly through it and are deflected by the internal magnetic field of the target in the extraction direction. The general properties of magnetic targets are examined theoretically and a specific devices and results of its testing are described

  9. Ice targets for use at NTOF

    International Nuclear Information System (INIS)

    Mercer, D.J.

    1992-12-01

    This report describes ice targets which were used during an experiment at the Neutron Time of Flight facility (NTOF) at LAMPF. Reasons for using the ice targets are given, and the construction, refrigeration system, and target preparation are detailed. Results of the research using these ice targets will be published at a later date

  10. A rotating target wheel system for gammasphere

    International Nuclear Information System (INIS)

    Greene, J. P.

    1999-01-01

    A description is given for a low-mass, rotating target wheel to be used within the Gammasphere target chamber. This system was developed for experiments employing high beam currents in order to extend lifetimes of targets using low-melting point target material. The design is based on a previously successful implementation of rotating target wheels for the Argonne Positron Experiment (APEX) as well as the Fragment Mass Analyser (FMA) at ATLAS (Argonne Tandem Linac Accelerator System). A brief history of these rotating target wheel systems is given as well as a discussion on target preparation and performance

  11. Target for production of X-rays

    Energy Technology Data Exchange (ETDEWEB)

    Korenev, S.A. E-mail: sergey_korenev@steris.com

    2004-10-01

    The patented new type of X-ray target is considered in this report. The main concept of the target consists in developing a sandwich structure depositing a coating of materials with high Z on the substrate with low Z, high thermal conductivity and high thermal stability. The target presents multiple layers system. The thermal conditions for X-ray target are discussed. The experimental results for Ta target on the Al and Cu substrates are presented.

  12. Target for production of X-rays

    International Nuclear Information System (INIS)

    Korenev, S.A.

    2004-01-01

    The patented new type of X-ray target is considered in this report. The main concept of the target consists in developing a sandwich structure depositing a coating of materials with high Z on the substrate with low Z, high thermal conductivity and high thermal stability. The target presents multiple layers system. The thermal conditions for X-ray target are discussed. The experimental results for Ta target on the Al and Cu substrates are presented

  13. Target for production of X-rays

    Science.gov (United States)

    Korenev, S. A.

    2004-09-01

    The patented new type of X-ray target is considered in this report. The main concept of the target consists in developing a sandwich structure depositing a coating of materials with high Z on the substrate with low Z, high thermal conductivity and high thermal stability. The target presents multiple layers system. The thermal conditions for X-ray target are discussed. The experimental results for Ta target on the Al and Cu substrates are presented.

  14. Hospitals: Soft Target for Terrorism?

    Science.gov (United States)

    De Cauwer, Harald; Somville, Francis; Sabbe, Marc; Mortelmans, Luc J

    2017-02-01

    In recent years, the world has been rocked repeatedly by terrorist attacks. Arguably, the most remarkable were: the series of four coordinated suicide plane attacks on September 11, 2001 on buildings in New York, Virginia, and Pennsylvania, USA; and the recent series of two coordinated attacks in Brussels (Belgium), on March 22, 2016, involving two bombings at the departure hall of Brussels International Airport and a bombing at Maalbeek Metro Station located near the European Commission headquarters in the center of Brussels. This statement paper deals with different aspects of hospital policy and disaster response planning that interface with terrorism. Research shows that the availability of necessary equipment and facilities (eg, personal protective clothing, decontamination rooms, antidotes, and anti-viral drugs) in hospitals clearly is insufficient. Emergency teams are insufficiently prepared: adequate and repetitive training remain necessary. Unfortunately, there are many examples of health care workers and physicians or hospitals being targeted in both political or religious conflicts and wars. Many health workers were kidnapped and/or killed by insurgents of various ideology. Attacks on hospitals also could cause long-term effects: hospital units could be unavailable for a long time and replacing staff could take several months, further compounding hospital operations. Both physical and psychological (eg, posttraumatic stress disorder [PTSD]) after-effects of a terrorist attack can be detrimental to health care services. On the other hand, physicians and other hospital employees have shown to be involved in terrorism. As data show that some offenders had a previous history with the location of the terror incident, the possibility of hospitals or other health care services being targeted by insiders is discussed. The purpose of this report was to consider how past terrorist incidents can inform current hospital preparedness and disaster response planning

  15. Targeting the GPI biosynthetic pathway.

    Science.gov (United States)

    Yadav, Usha; Khan, Mohd Ashraf

    2018-02-27

    The GPI (Glycosylphosphatidylinositol) biosynthetic pathway is a multistep conserved pathway in eukaryotes that culminates in the generation of GPI glycolipid which in turn anchors many proteins (GPI-APs) to the cell surface. In spite of the overall conservation of the pathway, there still exist subtle differences in the GPI pathway of mammals and other eukaryotes which holds a great promise so far as the development of drugs/inhibitors against specific targets in the GPI pathway of pathogens is concerned. Many of the GPI structures and their anchored proteins in pathogenic protozoans and fungi act as pathogenicity factors. Notable examples include GPI-anchored variant surface glycoprotein (VSG) in Trypanosoma brucei, GPI-anchored merozoite surface protein 1 (MSP1) and MSP2 in Plasmodium falciparum, protein-free GPI related molecules like lipophosphoglycans (LPGs) and glycoinositolphospholipids (GIPLs) in Leishmania spp., GPI-anchored Gal/GalNAc lectin and proteophosphoglycans in Entamoeba histolytica or the GPI-anchored mannoproteins in pathogenic fungi like Candida albicans. Research in this active area has already yielded encouraging results in Trypanosoma brucei by the development of parasite-specific inhibitors of GlcNCONH 2 -β-PI, GlcNCONH 2 -(2-O-octyl)-PI and salicylic hydroxamic acid (SHAM) targeting trypanosomal GlcNAc-PI de-N-acetylase as well as the development of antifungal inhibitors like BIQ/E1210/gepinacin/G365/G884 and YW3548/M743/M720 targeting the GPI specific fungal inositol acyltransferase (Gwt1) and the phosphoethanolamine transferase-I (Mcd4), respectively. These confirm the fact that the GPI pathway continues to be the focus of researchers, given its implications for the betterment of human life.

  16. Targeted Therapies for Lung Cancer.

    Science.gov (United States)

    Stinchcombe, Thomas E

    Targeted therapies have become standard therapies for patients with non-small cell lung cancer (NSCLC). A phase III trial of carboplatin and paclitaxel with and without bevacizumab in patients with advanced NSCLC with non-squamous histology demonstrated a statistically significant improvement in efficacy. In patients with NSCLC with an activating epidermal growth factor receptor (EGFR) mutation (defined as exon 19 deletion and exon 21 L858R point mutation), phase III trials of EGFR tyrosine kinase inhibitors (TKI) compared to platinum-based chemotherapy have demonstrated superior efficacy in the first-line setting. In patients with NSCLC with anaplastic lymphoma kinase (ALK) rearrangements, phase III trials of crizotinib have demonstrated superior efficacy compared to platinum-pemetrexed in the first-line setting and standard chemotherapy in the second-line setting. A second-generation ALK inhibitor, ceritinib, is available for patients who have progressed after or were intolerant of crizotinib. Crizotinib has also demonstrated activity on patients with ROS1 rearrangements, and BRAF inhibitors (dabrafenib, vemurafenib) have demonstrated activity in patients with NSCLC with BRAF V600E mutation. The oncogenic mutations that are susceptible to targeted therapy are mainly found in non-squamous NSCLC. The development of targeted therapy in patients with squamous NSCLC has been more challenging due to the genomic complexity observed in the squamous histology and the low prevalence of EGFR, ALK, and ROS1 molecular alterations. A phase III trial of cisplatin and gemcitabine with and without necitumumab in patients with advanced NSCLC with squamous histology demonstrated a statistically significant improvement in progression-free and overall survival.

  17. Introduction to radar target recognition

    CERN Document Server

    Tait, P

    2006-01-01

    This new text provides an overview of the radar target recognition process and covers the key techniques being developed for operational systems. It is based on the fundamental scientific principles of high resolution radar, and explains how the techniques can be used in real systems, taking into account the characteristics of practical radar system designs and component limitations. It also addresses operational aspects, such as how high resolution modes would fit in with other functions such as detection and tracking. Mathematics is kept to a minimum and the complex techniques and issues are

  18. HPV: Molecular pathways and targets.

    Science.gov (United States)

    Gupta, Shilpi; Kumar, Prabhat; Das, Bhudev C

    2018-04-05

    Infection of high-risk human papillomaviruses (HPVs) is a prerequisite for the development of cervical carcinoma. HPV infections are also implicated in the development of other types of carcinomas. Chronic or persistent infection of HPV is essential but HPV alone is inadequate, additional endogenous or exogenous cues are needed along with HPV to induce cervical carcinogenesis. The strategies that high-risk HPVs have developed in differentiating epithelial cells to reach a DNA-synthesis competent state leading to tumorigenic transformation are basically due to overexpression of the E6 and E7 oncoproteins and the activation of diverse cellular regulatory or signaling pathways that are targeted by them. Moreover, the Wnt/β-catenin/Notch and phosphoinositide 3-kinase (PI3K)/protein kinase B (Akt) pathways are deregulated in various cancers, and have also been implicated in HPV-induced cancers. These are basically related to the "cancer hallmarks," and include sustaining proliferative signals, the evasion of growth suppression and immune destruction, replicative immortality, inflammation, invasion, metastasis and angiogenesis, as well as genome instability, resisting cell death, and deregulation of cellular energetics. These information could eventually aid in identifying or developing new diagnostic, prognostic biomarkers, and may contribute to design more effective targeted therapeutics and treatment strategies. Although surgery, chemotherapy and radiotherapy can cure more than 90% of women with early stage cervical cancer, the recurrent and metastatic disease remains a major cause of cancer mortality. Numerous efforts have been made to design new drugs and develop gene therapies to treat cervical cancer. In recent years, research on treatment strategies has proposed several options, including the role of HPV E5, E6, and E7 oncogenes, which are retained and overexpressed in most of the cervical cancers and whose respective oncoproteins are critical to the induction

  19. Voyager 1 Saturn targeting strategy

    Science.gov (United States)

    Cesarone, R. J.

    1980-01-01

    A trajectory targeting strategy for the Voyager 1 Saturn encounter has been designed to accomodate predicted uncertainties in Titan's ephemeris while maximizing spacecraft safety and science return. The encounter is characterized by a close Titan flyby 18 hours prior to Saturn periapse. Retargeting of the nominal trajectory to account for late updates in Titan's estimated position can disperse the ascending node location, which is nominally situated at a radius of low expected particle density in Saturn's ring plane. The strategy utilizes a floating Titan impact vector magnitude to minimize this dispersion. Encounter trajectory characteristics and optimal tradeoffs are presented.

  20. Nova target chamber decontamination study

    International Nuclear Information System (INIS)

    1979-05-01

    An engineering study was performed to determine the most effective method for decontamination of the Nova target chamber. Manual and remote decontamination methods currently being used were surveyed. In addition, a concept that may not require in-situ decontamination was investigated. Based on the presently available information concerning material and system compatibility and particle penetration, it is recommended that a system of removable aluminum shields be considered. It is also recommended that a series of tests be performed to more precisely determine the vacuum compatibility and penetrability of other materials discussed in this report

  1. Biomimetic nanoparticles for inflammation targeting

    Directory of Open Access Journals (Sweden)

    Kai Jin

    2018-01-01

    Full Text Available There have been many recent exciting developments in biomimetic nanoparticles for biomedical applications. Inflammation, a protective response involving immune cells, blood vessels, and molecular mediators directed against harmful stimuli, is closely associated with many human diseases. As a result, biomimetic nanoparticles mimicking immune cells can help achieve molecular imaging and precise drug delivery to these inflammatory sites. This review is focused on inflammation-targeting biomimetic nanoparticles and will provide an in-depth look at the design of these nanoparticles to maximize their benefits for disease diagnosis and treatment.

  2. Target raster system at CEBAF

    International Nuclear Information System (INIS)

    Yan, C.; Adderley, P.; Carlini, R.; Cuevas, C.; Vulcan, W.; Wines, R.

    1995-01-01

    A fast raster (FR) system consisting of two Litz cable air-core magnets (x, y) has been installed and tested in the Hall C beam line tunnel, 21 m from the cryogenic target. The system provides a maximum deflection of 0.06 mrad at a frequency range of 15-45 kHz for a 6 GeV electron beam. The FR magnets are driven by a MOSFET bipolar switching power source with a triangle current waveform, the peak-to-peak current is 40 A. (orig.)

  3. The future of targeted peptidomics.

    Science.gov (United States)

    Findeisen, Peter

    2013-12-01

    Targeted MS is becoming increasingly important for sensitive and specific quantitative detection of proteins and respective PTMs. In this article, Ceglarek et al. [Proteomics Clin. Appl. 2013, 7, 794-801] present an LC-MS-based method for simultaneous quantitation of seven apolipoproteins in serum specimens. The assay fulfills many necessities of routine diagnostic applications, namely, low cost, high throughput, and good reproducibility. We anticipate that validation of new biomarkers will speed up with this technology and the palette of laboratory-based diagnostic tools will hopefully be augmented significantly in the near future. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. LIFE Target Fabrication Research Plan Sept 2008

    Energy Technology Data Exchange (ETDEWEB)

    Miles, R; Biener, J; Kucheyev, S; Montesanti, R; Satcher, J; Spadaccini, C; Rose, K; Wang, M; Hamza, A; Alexander, N; Brown, L; Hund, J; Petzoldt, R; Sweet, W; Goodin, D

    2008-11-10

    The target-system for the baseline LIFE fast-ignition target was analyzed to establish a preliminary estimate for the costs and complexities involved in demonstrating the technologies needed to build a prototype LIFE plant. The baseline fast-ignition target upon which this analysis was developed is shown in Figure 1.0-1 below. The LIFE target-system incorporates requirements for low-cost, high throughput manufacture, high-speed, high accuracy injection of the target into the chamber, production of sufficient energy from implosion and recovery and recycle of the imploded target material residue. None of these functions has been demonstrated to date. Existing target fabrication techniques which lead to current 'hot spot' target costs of {approx}$100,000 per target and at a production rate of 2/day are unacceptable for the LIFE program. Fabrication techniques normally used for low-cost, low accuracy consumer products such as toys must be adapted to the high-accuracy LIFE target. This will be challenge. A research program resulting is the demonstration of the target-cycle technologies needed for a prototype LIFE reactor is expected to cost {approx}$51M over the course of 5 years. The effort will result in targets which will cost an estimated $0.23/target at a rep-rate of 20 Hz or about 1.73M targets/day.

  5. Targeted therapy of multiple myeloma.

    Science.gov (United States)

    Dolloff, Nathan G; Talamo, Giampaolo

    2013-01-01

    Multiple myeloma (MM) is a plasma cell malignancy and the second most common hematologic cancer. MM is characterized by the accumulation of malignant plasma cells within the bone marrow, and presents clinically with a broad range of symptoms, including hypercalcemia, renal insufficiency, anemia, and lytic bone lesions. MM is a heterogeneous disease associated with genomic instability, where patients may express multiple genetic abnormalities that affect several oncogenic pathways. Commonly detected genetic aberrations are translocations involving immunoglobulin heavy chain (IgH) switch regions (chromosome 14q32) and oncogenes such as c-maf [t(14:16)], cyclin D1 [t(11:14)], and FGFR3/MMSET [t(4:14)]. Advances in the basic understanding of MM and the development of novel agents, such as the immunomodulatory drugs (IMiDs) thalidomide and lenalidomide and the proteasome inhibitor bortezomib, have increased therapeutic response rates and prolonged patient survival. Despite these advances MM remains incurable in the majority of patients, and it is therefore critical to identify additional therapeutic strategies and targets for its treatment. In this chapter, we review the underlying genetic components of MM and discuss the results of recent clinical trials that demonstrate the effectiveness of targeted agents in the management of MM. In addition, we discuss experimental therapies that are currently in clinical development along with their molecular rationale in the treatment of MM.

  6. Synthetic membrane-targeted antibiotics.

    Science.gov (United States)

    Vooturi, S K; Firestine, S M

    2010-01-01

    Antimicrobial resistance continues to evolve and presents serious challenges in the therapy of both nosocomial and community-acquired infections. The rise of resistant strains like methicillin-resistant Staphylococcus aureus (MRSA), vancomycin-resistant Staphylococcus aureus (VRSA) and vancomycin-resistant enterococci (VRE) suggests that antimicrobial resistance is an inevitable evolutionary response to antimicrobial use. This highlights the tremendous need for antibiotics against new bacterial targets. Agents that target the integrity of bacterial membrane are relatively novel in the clinical armamentarium. Daptomycin, a lipopeptide is a classical example of membrane-bound antibiotic. Nature has also utilized this tactic. Antimicrobial peptides (AMPs), which are found in all kingdoms, function primarily by permeabilizing the bacterial membrane. AMPs have several advantages over existing antibiotics including a broad spectrum of activity, rapid bactericidal activity, no cross-resistance with the existing antibiotics and a low probability for developing resistance. Currently, a small number of peptides have been developed for clinical use but therapeutic applications are limited because of poor bioavailability and high manufacturing cost. However, their broad specificity, potent activity and lower probability for resistance have spurred the search for synthetic mimetics of antimicrobial peptides as membrane-active antibiotics. In this review, we will discuss the different classes of synthetic membrane-bound antibiotics published since 2004.

  7. 'Treat to Target' - Lessons Learnt.

    Science.gov (United States)

    Kurti, Zsuzsanna; Vegh, Zsuzsanna; Golovics, Petra Anna; Lakatos, Peter Laszlo

    2016-01-01

    Therapeutic management in inflammatory bowel diseases (IBD) has significantly changed in the last decades with the advent of biological therapy resulting in new treatment targets other than clinical symptoms. Patient stratification in the early stage of the disease is an important step to identify patients with poor prognosis, who might benefit from early aggressive treatment to avoid complications in the later disease course. Recent randomized and hypothesis driven (e.g., Randomized Evaluation of an Algorithm for Crohn's Treatment, Post-Operative Crohn's Endoscopic Recurrence) clinical trials conducted in the biological era underscore the need of objective disease monitoring including assessment of biomarkers (e.g., C-reactive protein and calprotectin), mucosal healing and, for biologically treated patients, therapeutic drug monitoring beside clinical symptom assessment in both Crohn's disease and ulcerative colitis. Assessing the treatment efficacy objectively has become an important element of patient monitoring besides clinical symptom assessment. Further clinical studies are needed to assess whether implementation of new therapeutic algorithms based on these targets and tight monitoring in clinical practice have the potential to further improve long-term disease outcomes in IBD. © 2016 S. Karger AG, Basel.

  8. Properties of Protein Drug Target Classes

    Science.gov (United States)

    Bull, Simon C.; Doig, Andrew J.

    2015-01-01

    Accurate identification of drug targets is a crucial part of any drug development program. We mined the human proteome to discover properties of proteins that may be important in determining their suitability for pharmaceutical modulation. Data was gathered concerning each protein’s sequence, post-translational modifications, secondary structure, germline variants, expression profile and drug target status. The data was then analysed to determine features for which the target and non-target proteins had significantly different values. This analysis was repeated for subsets of the proteome consisting of all G-protein coupled receptors, ion channels, kinases and proteases, as well as proteins that are implicated in cancer. Machine learning was used to quantify the proteins in each dataset in terms of their potential to serve as a drug target. This was accomplished by first inducing a random forest that could distinguish between its targets and non-targets, and then using the random forest to quantify the drug target likeness of the non-targets. The properties that can best differentiate targets from non-targets were primarily those that are directly related to a protein’s sequence (e.g. secondary structure). Germline variants, expression levels and interactions between proteins had minimal discriminative power. Overall, the best indicators of drug target likeness were found to be the proteins’ hydrophobicities, in vivo half-lives, propensity for being membrane bound and the fraction of non-polar amino acids in their sequences. In terms of predicting potential targets, datasets of proteases, ion channels and cancer proteins were able to induce random forests that were highly capable of distinguishing between targets and non-targets. The non-target proteins predicted to be targets by these random forests comprise the set of the most suitable potential future drug targets, and should therefore be prioritised when building a drug development programme. PMID

  9. Temperature simulations for the SPIRAL ISOL target

    International Nuclear Information System (INIS)

    Maunoury, L.; Bajeat, O.; Lichtenthaler, R.; Villari, A.C.C.

    2001-01-01

    Simulations of the power deposition and target temperature distributions in the SPIRAL ISOL target are presented. These simulations consider different heavy-ion beams with intensities corresponding to 2 and 6 kW on a carbon target. A new solutions, which corresponds to the splitting of the production target into two parts, where the first is cooled and the second is heated, allows keeping the overall size of the target ensemble relatively small. An extrapolation of the considered target geometry to primary beam intensities up to 1 MW is also presented. (authors)

  10. Bispecific antibodies targeting human CD73

    DEFF Research Database (Denmark)

    2017-01-01

    The present invention relates to a bispecific antibody targeting CD73. In particular, the present invention relates to a bispecific antibody targeting different epitopes on CD73 or a bispecific antibody targeting an epitope on CD73 and an epitope on a different antigen.......The present invention relates to a bispecific antibody targeting CD73. In particular, the present invention relates to a bispecific antibody targeting different epitopes on CD73 or a bispecific antibody targeting an epitope on CD73 and an epitope on a different antigen....

  11. High heat flux cooling for accelerator targets

    International Nuclear Information System (INIS)

    Silverman, I.; Nagler, A.

    2002-01-01

    Accelerator targets, both for radioisotope production and for high neutron flux sources generate very high thermal power in the target material which absorbs the particles beam. Generally, the geometric size of the targets is very small and the power density is high. The design of these targets requires dealing with very high heat fluxes and very efficient heat removal techniques in order to preserve the integrity of the target. Normal heat fluxes from these targets are in the order of 1 kw/cm 2 and may reach levels of an order of magnitude higher

  12. QUIKVIS- CELESTIAL TARGET AVAILABILITY INFORMATION

    Science.gov (United States)

    Petruzzo, C.

    1994-01-01

    QUIKVIS computes the times during an Earth orbit when geometric requirements are satisfied for observing celestial objects. The observed objects may be fixed (stars, etc.) or moving (sun, moon, planets). QUIKVIS is useful for preflight analysis by those needing information on the availability of celestial objects to be observed. Two types of analyses are performed by QUIKVIS. One is used when specific objects are known, the other when targets are unknown and potentially useful regions of the sky must be identified. The results are useful in selecting candidate targets, examining the effects of observation requirements, and doing gross assessments of the effects of the orbit's right ascension of the ascending node (RAAN). The results are not appropriate when high accuracy is needed (e.g. for scheduling actual mission operations). The observation duration is calculated as a function of date, orbit node, and geometric requirements. The orbit right ascension of the ascending node can be varied to account for the effects of an uncertain launch time of day. The orbit semimajor axis and inclination are constant throughout the run. A circular orbit is assumed, but a simple program modification will allow eccentric orbits. The geometric requirements that can be processed are: 1) minimum separation angle between the line of sight to the object and the earth's horizon; 2) minimum separation angle between the line of sight to the object and the spacecraft velocity vector; 3) maximum separation angle between the line of sight to the object and the zenith direction; and 4) presence of the spacecraft in the earth's shadow. The user must supply a date or date range, the spacecraft orbit and inclination, up to 700 observation targets, and any geometric requirements to be met. The primary output is the time per orbit that conditions are satisfied, with options for sky survey maps, time since a user-specified orbit event, and bar graphs illustrating overlapping requirements. The

  13. HIRFL–CSR internal cluster target

    International Nuclear Information System (INIS)

    Shao, Caojie; Lu, Rongchun; Cai, Xiaohong; Yu, Deyang; Ruan, Fangfang; Xue, Yingli; Zhang, Jianming; Torpokov, D.K.; Nikolenko, D.

    2013-01-01

    Highlights: • An internal cluster target was built and installed at HIRFL–CSR. • The target thickness for H 2 amounts up to 6.6 × 10 12 atoms/cm 2 . • The feasibility and stability of the internal cluster target were verified by on-line experiments. -- Abstract: Since HIRFL–CSR internal cluster target was built, it has played a key role in in-ring experiments at HIRFL–CSR. So far it have been operated with five gas species as targets for scattering experiments, i.e. hydrogen, nitrogen, argon, neon, and krypton. The obtained highest thickness for hydrogen target amounts up to 10 12 atoms/cm 2 , and those of other targets are larger than 10 13 atoms/cm 2 with the background pressure of 10 −11 mbar in CSR. The target thickness can be varied by regulating the nozzle temperature and pressure of the inlet gas. The first online internal target experiment dedicated to investigate radioactive electron capture (REC) process with Xe 54+ ions colliding with the nitrogen target demonstrated the stability and reliability of the internal target system. In addition, hydrogen and krypton were also tested online in recent experiments, which indicate the target system can meet experimental requirements for the thickness of target, pressure in scattering chamber, and long-term stability

  14. Targeting α-synuclein oligomers

    DEFF Research Database (Denmark)

    van Diggelen, Femke

    Parkinson’s Disease (PD) is a complex disease, characterised by degeneration of neocortical, limbic and nigrostriatal neurons. It is unknown what initiates neurodegeneration, but soluble oligomers of the protein α-synuclein (αSn) seem to be particularly toxic, compared to insoluble fibrils...... unique characteristics, e.g. they were recognized by different conformational antibodies and DHA–αSOs also formed a second elongated species in addition to the dominant spherical species. Although further functional testing is needed, this suggests that each species has its own distinct toxic mechanism......+/K+ ATPase, V-type ATPase, VDAC, CaMKII and Rab-3A. The identification of these targets is a first step towards unravelling the toxic pathways which are activated upon synaptic binding of extracellularly added αSOs, and hopefully will contribute to the discovery of new disease modifying compounds, which can...

  15. Target design for shock ignition

    International Nuclear Information System (INIS)

    Schurtz, G; Ribeyre, X; Lafon, M

    2010-01-01

    The conventional approach of laser driven inertial fusion involves the implosion of cryogenic shells of deuterium-tritium ice. At sufficiently high implosion velocities, the fuel ignites by itself from a central hot spot. In order to reduce the risks of hydrodynamic instabilities inherent to large implosion velocities, it was proposed to compress the fuel at low velocity, and ignite the compressed fuel by means of a convergent shock wave driven by an intense spike at the end of the laser pulse. This scheme, known as shock ignition, reduces the risks of shell break-up during the acceleration phase, but it may be impeded by a low coupling efficiency of the laser pulse with plasma at high intensities. This work provides a relationship between the implosion velocity and the laser intensity required to ignite the target by a shock. The operating domain of shock ignition at different energies is described.

  16. Therapeutic target for protozoal diseases

    Science.gov (United States)

    Rathore, Dharmendar [Blacksburg, VA; Jani, Dewal [Blacksburg, VA; Nagarkatti, Rana [Blacksburg, VA

    2008-10-21

    A novel Fasciclin Related Adhesive Protein (FRAP) from Plasmodium and related parasites is provided as a target for therapeutic intervention in diseases caused by the parasites. FRAP has been shown to play a critical role in adhesion to, or invasion into, host cells by the parasite. Furthermore, FRAP catalyzes the neutralization of heme by the parasite, by promoting its polymerization into hemozoin. This invention provides methods and compositions for therapies based on the administration of protein, DNA or cell-based vaccines and/or antibodies based on FRAP, or antigenic epitopes of FRAP, either alone or in combination with other parasite antigens. Methods for the development of compounds that inhibit the catalytic activity of FRAP, and diagnostic and laboratory methods utilizing FRAP are also provided.

  17. Performance Targets and External Benchmarking

    DEFF Research Database (Denmark)

    Friis, Ivar; Hansen, Allan; Vámosi, Tamás S.

    Research on relative performance measures, transfer pricing, beyond budgeting initiatives, target costing, piece rates systems and value based management has for decades underlined the importance of external benchmarking in performance management. Research conceptualises external benchmarking...... as a market mechanism that can be brought inside the firm to provide incentives for continuous improvement and the development of competitive advances. However, whereas extant research primarily has focused on the importance and effects of using external benchmarks, less attention has been directed towards...... the conditions upon which the market mechanism is performing within organizations. This paper aims to contribute to research by providing more insight to the conditions for the use of external benchmarking as an element in performance management in organizations. Our study explores a particular type of external...

  18. Apoptosis: Targets in Pancreatic Cancer

    Directory of Open Access Journals (Sweden)

    Kalthoff Holger

    2003-01-01

    Full Text Available Abstract Pancreatic adenocarcinoma is characterized by poor prognosis, because of late diagnosis and lack of response to chemo- and/or radiation therapies. Resistance to apoptosis mainly causes this insensitivity to conventional therapies. Apoptosis or programmed cell death is a central regulator of tissue homeostasis. Certain genetic disturbances of apoptotic signaling pathways have been found in carcinomas leading to tumor development and progression. In the past few years, the knowledge about the complex pathways of apoptosis has strongly increased and new therapeutic approaches based on this knowledge are being developed. This review will focus on the role of apoptotic proteins contributing to pancreatic cancer development and progression and will demonstrate possible targets to influence this deadly disease.

  19. Gene Therapy Targeting HIV Entry

    Directory of Open Access Journals (Sweden)

    Chuka Didigu

    2014-03-01

    Full Text Available Despite the unquestionable success of antiretroviral therapy (ART in the treatment of HIV infection, the cost, need for daily adherence, and HIV-associated morbidities that persist despite ART all underscore the need to develop a cure for HIV. The cure achieved following an allogeneic hematopoietic stem cell transplant (HSCT using HIV-resistant cells, and more recently, the report of short-term but sustained, ART-free control of HIV replication following allogeneic HSCT, using HIV susceptible cells, have served to both reignite interest in HIV cure research, and suggest potential mechanisms for a cure. In this review, we highlight some of the obstacles facing HIV cure research today, and explore the roles of gene therapy targeting HIV entry, and allogeneic stem cell transplantation in the development of strategies to cure HIV infection.

  20. TARGET 2 and Settlement Finality

    Directory of Open Access Journals (Sweden)

    Ivan MANGATCHEV

    2011-03-01

    Full Text Available This article examines how TARGET 2 as system implements the idea of settlement finality regulated by Directive 98/26 EC of the European parliament and of the Council of 19 May 1998 on settlement finality in payment and securities settlement systems (Settlement Finality Directive and Directive 2009/44/EC of the European parliament and of the Council of 6 May 2009 amending Directive 98/26/EC on settlement finality in payment and securities settlement systems and Directive 2002/47/EC on financial collateral arrangements as regards linked systems and credit claims (Directive 2009/44/EC. As the title of the arti and finality of the settlement in this system.