Dosimetry in the region of 0.25 Mrad and 25 Mrad using cellulose triacetate films (CTA)

International Nuclear Information System (INIS)

Dafferner, J.M.

1978-01-01

The dosimetric characteristics of a cellulose triacetate dosimetric film (CTA) from different places of origin, recently placed on the market to be used in dosimetry, are investigated. The charge in the optical absorption in the ultraviolet region induced by gamma radiation of Co-60 is found to be a linear behavior with the absorbed total dose, within a range of 0.25 to 25 Megarad. For the spectrophotometric reading the wavelength of 290 nm was chosen for the French CTA film, while 294 nm was used for the Japanese one. The response of the film is stable in time after the irradiation. By means of an adequate and careful handling the response does not change. One must always maintain, in practical usage, the same conditions of irradiation and the spectrophotometric reading used in the calibration. This film appears well suited for monitoring and control the dose of industrial irradiation process such as: process that involve application of chemical effects undergo by polymers when irradiated (polymerization), radiosterilization of medical products and equipments, food sterillization etc. (Author) [pt

Carprofen-imprinted monolith prepared by reversible addition-fragmentation chain transfer polymerization in room temperature ionic liquids.

Science.gov (United States)

Ban, Lu; Han, Xu; Wang, Xian-Hua; Huang, Yan-Ping; Liu, Zhao-Sheng

2013-10-01

To obtain fast separation, ionic liquids were used as porogens first in combination with reversible addition-fragmentation chain transfer (RAFT) polymerization to prepare a new type of molecularly imprinted polymer (MIP) monolith. The imprinted monolithic column was synthesized using a mixture of carprofen (template), 4-vinylpyridine, ethylene glycol dimethacrylate, [BMIM]BF4, and chain transfer agent (CTA). Some polymerization factors, such as template-monomer molar ratio, the degree of crosslinking, the composition of the porogen, and the content of CTA, on the column efficiency and imprinting effect of the resulting MIP monolith were systematically investigated. Affinity screening of structurally similar compounds with the template can be achieved in 200 s on the MIP monolith due to high column efficiency (up to 12,070 plates/m) and good column permeability. Recognition mechanism of the imprinted monolith was also investigated.

VLBI imaging of CTA 102

International Nuclear Information System (INIS)

Wehrle, A.E.; Cohen, M.

1989-01-01

The object CTA 102, a low-frequency variable quasar, was observed with a VLBI Global Array in 1987.5 and 1988.5 at 5.0 GHz. The structure is complex, with three compact components along a line at PA = 157 deg, and several extended, ill-defined components east of the southernmost compact component. The components have no detectable relative motions, with mu less than 0.5 mas/yr along the main axis. This contrasts with the observation reported by Baath (1987), who found mu = 0.65 + or - 0.15 mas/yr at 932 MHz, which is exceptionally high. The new upper limit allows CTA 102 to be in the normal range of superluminal sources. 11 refs

Added value of multiphase CTA imaging for thrombus perviousness assessment

Energy Technology Data Exchange (ETDEWEB)

Santos, E.M.M. [Academic Medical Center, Department of Biomedical Engineering and Physics, Amsterdam (Netherlands); Erasmus Medical Center, Department of Medical Informatics, Rotterdam (Netherlands); D' Esterre, C.D.; Najm, M.; Goyal, M.; Demchuk, A.M.; Menon, B.K. [University of Calgary, Departments of Neurosciences, Radiology and Community Health Sciences, Calgary (Canada); Treurniet, K.M.; Majoie, C.B. [Academic Medical Center, Department of Radiology and Nuclear Medicine, Amsterdam (Netherlands); Niessen, W.J. [Erasmus Medical Center, Department of Medical Informatics, Rotterdam (Netherlands); Delft University of Technology, Faculty of Applied Sciences, Delft (Netherlands); Marquering, H.A. [Academic Medical Center, Department of Biomedical Engineering and Physics, Amsterdam (Netherlands); Academic Medical Center, Department of Radiology and Nuclear Medicine, Amsterdam (Netherlands); Mandzia, Jennifer; Fainardi, Enrico; Rubiera, Marta; Khaw, Alexander V.; Zini, Andrea; Shankar, JJ.; Collaboration: PRove-IT investigators

2018-01-15

Thrombus perviousness has been associated with favorable functional outcome in acute ischemic stroke (AIS) patients. Measuring thrombus perviousness on CTA may be suboptimal due to potential delay in contrast agent arrival in occluded arteries at the moment of imaging. Dynamic sequences acquired over time can potentially overcome this issue. We investigate if dynamic CTA has added value in assessing thrombus perviousness. Prospectively collected image data of AIS patients with proven occlusion of the anterior or posterior circulation with thin-slice multi-phase CTA (MCTA) and non-contrast CT were co-registered (n = 221). Thrombus attenuation increase (TAI; a perviousness measure) was measured for the arterial, venous, and delayed phase of the MCTA and time-invariant CTAs (TiCTA). Associations with favorable clinical outcome (90-day mRS ≤ 2) were assessed using univariate and multivariable regressions and calculating areas under receiver operating curves (AUC). TAI determined from the arterial phase CTA was superior in the association with favorable outcome with OR = 1.21 per 10 HU increase (95%CI 1.04-1.41, AUC 0.62, p = 0.014) compared to any other phase (venous 1.14(95%CI 1.01-1.30, AUC 0.58, p = 0.033), delayed 1.046(95%CI 0.919-1.19, AUC 0.53, p = 0.50)), and TiCTA 1.15(95%CI 1.02-1.30, AUC 0.60, p = 0.022). In the multivariable model, only TAI on arterial phase was significantly associated with favorable outcome (aOR 1.59, 95%CI 1.04-2.43, p = 0.032). Association between TAI with functional outcome was optimal on arterial-phase CTA such that dynamic CTA imaging has no additional benefits in current thrombus perviousness assessment, thereby suggesting that the delay of contrast arrival at the clot is a key variable for patient functional outcome. (orig.)

RAFT Aqueous Dispersion Polymerization of N-(2-(Methacryloyloxy)ethyl)pyrrolidone: A Convenient Low Viscosity Route to High Molecular Weight Water-Soluble Copolymers.

Science.gov (United States)

Cunningham, Victoria J; Derry, Matthew J; Fielding, Lee A; Musa, Osama M; Armes, Steven P

2016-06-28

RAFT solution polymerization of N -(2-(methacryoyloxy)ethyl)pyrrolidone (NMEP) in ethanol at 70 °C was conducted to produce a series of PNMEP homopolymers with mean degrees of polymerization (DP) varying from 31 to 467. Turbidimetry was used to assess their inverse temperature solubility behavior in dilute aqueous solution, with an LCST of approximately 55 °C being observed in the high molecular weight limit. Then a poly(glycerol monomethacylate) (PGMA) macro-CTA with a mean DP of 63 was chain-extended with NMEP using a RAFT aqueous dispersion polymerization formulation at 70 °C. The target PNMEP DP was systematically varied from 100 up to 6000 to generate a series of PGMA 63 -PNMEP x diblock copolymers. High conversions (≥92%) could be achieved when targeting up to x = 5000. GPC analysis confirmed high blocking efficiencies and a linear evolution in M n with increasing PNMEP DP. A gradual increase in M w / M n was also observed when targeting higher DPs. However, this problem could be minimized ( M w / M n RAFT aqueous dispersion polymerization of NMEP was approximately four times faster than the RAFT solution polymerization of NMEP in ethanol when targeting the same DP in each case. This is perhaps surprising because both 1 H NMR and SAXS studies indicate that the core-forming PNMEP chains remain relatively solvated at 70 °C in the latter formulation. Moreover, dissolution of the initial PGMA 63 -PNMEP x particles occurs on cooling from 70 to 20 °C as the PNMEP block passes through its LCST. Hence this RAFT aqueous dispersion polymerization formulation offers an efficient route to a high molecular weight water-soluble polymer in a rather convenient low-viscosity form. Finally, the relatively expensive PGMA macro-CTA was replaced with a poly(methacrylic acid) (PMAA) macro-CTA. High conversions were also achieved for PMAA 85 -PNMEP x diblock copolymers prepared via RAFT aqueous dispersion polymerization for x ≤ 4000. Again, better control was achieved when

Automatic aortic root segmentation in CTA whole-body dataset

Science.gov (United States)

Gao, Xinpei; Kitslaar, Pieter H.; Scholte, Arthur J. H. A.; Lelieveldt, Boudewijn P. F.; Dijkstra, Jouke; Reiber, Johan H. C.

2016-03-01

Trans-catheter aortic valve replacement (TAVR) is an evolving technique for patients with serious aortic stenosis disease. Typically, in this application a CTA data set is obtained of the patient's arterial system from the subclavian artery to the femoral arteries, to evaluate the quality of the vascular access route and analyze the aortic root to determine if and which prosthesis should be used. In this paper, we concentrate on the automated segmentation of the aortic root. The purpose of this study was to automatically segment the aortic root in computed tomography angiography (CTA) datasets to support TAVR procedures. The method in this study includes 4 major steps. First, the patient's cardiac CTA image was resampled to reduce the computation time. Next, the cardiac CTA image was segmented using an atlas-based approach. The most similar atlas was selected from a total of 8 atlases based on its image similarity to the input CTA image. Third, the aortic root segmentation from the previous step was transferred to the patient's whole-body CTA image by affine registration and refined in the fourth step using a deformable subdivision surface model fitting procedure based on image intensity. The pipeline was applied to 20 patients. The ground truth was created by an analyst who semi-automatically corrected the contours of the automatic method, where necessary. The average Dice similarity index between the segmentations of the automatic method and the ground truth was found to be 0.965±0.024. In conclusion, the current results are very promising.

ITER CTA newsletter. No. 15, December 2002

International Nuclear Information System (INIS)

2003-03-01

This ITER CTA newsletter issue contains brief information about several meetings related to ITER. One of them is the seventh ITER Negotiations Meetings that took place in Barcelona, Spain on 9-10 December 2002, another is the final ITER CTA Project Board Meeting, which took place in Barcelona, Spain on 8 December 2002 and the last one is the Third Meeting of the International Tokamak Physics Activity (ITPA) Topical Group on diagnostics held in Toki, Japan on 18-21 September 2002

ITER CTA newsletter. No. 12, September 2002

International Nuclear Information System (INIS)

2002-11-01

This ITER CTA newsletter issue comprises information about two ITER meetings: The meeting of the ITER CTA Project Board (PB), which took place in Toronto, Canada on 16 September 2002 on the occasion of the fifth Negotiations Meeting (N-5) and the second meeting of the International Tokamak Physics Activity (ITPA) coordinating committee, consisting of representatives from the ITPA participants and the topical physics group chairs and co-chairs, which was held at GA Technologies, San Diego, USA on 1-2 March 2002

Strategy implementation for the CTA Atmospheric monitoring program

Directory of Open Access Journals (Sweden)

Doro Michele

2015-01-01

Full Text Available The Cherenkov Telescope Array (CTA is the next generation facility of Imaging Atmospheric Cherenkov Telescopes. It reaches unprecedented sensitivity and energy resolution in very-high-energy gamma-ray astronomy. CTA detects Cherenkov light emitted within an atmospheric shower of particles initiated by cosmic-gamma rays or cosmic rays entering the Earth's atmosphere. From the combination of images the Cherenkov light produces in the telescopes, one is able to infer the primary particle energy and direction. A correct energy estimation can be thus performed only if the local atmosphere is well characterized. The atmosphere not only affects the shower development itself, but also the Cherenkov photon transmission from the emission point in the particle shower, at about 10–20 km above the ground, to the detector. Cherenkov light on the ground is peaked in the UV-blue region, and therefore molecular and aerosol extinction phenomena are important. The goal of CTA is to control systematics in energy reconstruction to better than 10%. For this reason, a careful and continuous monitoring and characterization of the atmosphere is required. In addition, CTA will be operated as an observatory, with data made public along with appropriate analysis tools. High-level data quality can only be ensured if the atmospheric properties are consistently and continuously taken into account. In this contribution, we concentrate on discussing the implementation strategy for the various atmospheric monitoring instruments currently under discussion in CTA. These includes Raman lidars and ceilometers, stellar photometers and others available both from commercial providers and public research centers.

Meeting of the ITER CTA Project Board

International Nuclear Information System (INIS)

2001-01-01

Full text: A preparatory meeting of the Co-ordinated Technical Activities (CTA) Project Board took place in Vienna on 16 July 2001. The Board Members of Canada, EU, Japan, RF and of the CTA International Team participated in the Meeting, which was chaired by Acad. E. Velikhov. The major item on the Meeting Agenda was the discussion of the scope of the CTA. In this discussion the following comments were expressed: One of the prime objectives during the CTA is to develop technical specifications for procurement of critical items (magnets, vacuum vessel, and buildings). It was noted that the discussions with potential suppliers should confirm manufacturing processes in details in order to explore possible schedule reduction strategies. Safety analysis and licensing preparation should proceed on all proposed sites up to the preferred site designation, to ensure the overall implementation schedule is minimized and to resolve major technical issues needed for licensing. Several R and D issues remain to be further developed during the CTA. Special attention should be given by the Participants to two areas: Diagnostics; Heating and Current Drive Systems. Arrangements for continuation of the ITER Physics Expert Groups activities should be provided. To this end a new framework, called International Tokamak Physics Activity, is being planned. The Board encouraged the Participants' Representatives in the Co-ordinating committee of this activity to support the preparation for urgent Topical Group Meetings. The Board agreed that the Design Authority will be invested in the International Team and that proposals for site specific design changes should be agreed upon by the International Team Leader before being studied in detail. The Meeting agreed on some arrangements which will remain from the EDA, namely the ITER EDA Council Office in Moscow as Office of the PB Chair, and the ITER Office located at the IAEA in Vienna as agreed by the IAEA. The Board recommended that effective

Meeting of the ITER CTA Project Board

International Nuclear Information System (INIS)

Vlasenkov, V.

2001-01-01

The meeting of the ITER CTA Project Board took place in Toronto, Canada on 7 November 2001, on the occasion of the first Negotiations Meeting. Twelve participants, representing PB members and experts from Canada, the EU, Japan, the RF and the international Team (IT), attended the meeting chaired by Acad. E. Velikhov. Discussions on the preliminary work programme for the CTA and organizational arrangements for the IT and PT took most of the time of the meeting. The Project Board approved the preliminary work programme as presented by the IT leader

Preparation and Applications of Amylose Supramolecules by Means of Phosphorylase-Catalyzed Enzymatic Polymerization

Directory of Open Access Journals (Sweden)

Jun-ichi Kadokawa

2012-01-01

Full Text Available This paper reviews preparation and applications of amylose supramolecules by means of phosphorylase-catalyzed enzymatic polymerization. When the enzymatic polymerization of α-d-glucose 1-phosphate (G-1-P as a monomer was carried out in the presence of poly(tetrahydrofuran (PTHF of a hydrophobic polyether as a guest polymer, the supramolecule, i.e., an amylose-PTHF inclusion complex, was formed in the process of polymerization. Because the representation of propagation in the polymerization is similar to the way that vines of plants grow twining around rods, this polymerization method for the preparation of amylose-polymer inclusion complexes was proposed to be named “vine-twining polymerization”. Various hydrophobic polyethers, polyesters, poly(ester-ether, and polycarbonates were also employed as the guest polymer in the vine-twining polymerization to produce the corresponding inclusion complexes. To obtain the inclusion complex from a strongly hydrophobic guest polymer, the parallel enzymatic polymerization system was developed as an advanced extension of the vine-twining polymerization. In addition, it was found that amylose selectively includes one side of the guest polymer from a mixture of two resemblant guest polymers, as well as a specific range in molecular weights of the guest PTHF. Amylose also exhibited selective inclusion behavior toward stereoisomers of poly(lactides. Moreover, the preparation of hydrogels through the formation of inclusion complexes of amylose in vine-twining polymerization was achieved.

ITER CTA newsletter. No. 8

International Nuclear Information System (INIS)

2002-05-01

This ITER CTA newsletter contains information about the Third Negotiations Meeting on the Joint Implementation of ITER held in Moscow on 23-24 April 2002 and about the visit of Canadian officials and members of the Canadian delegation to RF research center 'Kurchatov Institute'

ITER CTA newsletter. No. 2

International Nuclear Information System (INIS)

2001-10-01

This ITER CTA newsletter contains results of the ITER toroidal field model coil project presented by ITER EU Home Team (Garching) and an article in commemoration of the late Dr. Charles Maisonnier, one of the former leaders of ITER who made significant contributions to its development

CTA-enhanced perfusion CT: an original method to perform ultra-low-dose CTA-enhanced perfusion CT

Energy Technology Data Exchange (ETDEWEB)

Tong, Elizabeth; Wintermark, Max [University of Virginia, Department of Radiology, Neuroradiology Division, Charlottesville, VA (United States)

2014-11-15

Utilizing CT angiography enhances image quality in PCT, thereby permitting acquisition at ultra-low dose. Dynamic CT acquisitions were obtained at 80 kVp with decreasing tube current-time product [milliamperes x seconds (mAs)] in patients suspected of ischemic stroke, with concurrent CTA of the cervical and intracranial arteries. By utilizing fast Fourier transformation, high spatial frequencies of CTA were combined with low spatial frequencies of PCT to create a virtual PCT dataset. The real and virtual PCT datasets with decreasing mAs were compared by assessing contrast-to-noise ratio (CNR), signal-to-noise ratio (SNR), and noise and PCT values and by visual inspection of PCT parametric maps. Virtual PCT attained CNR and SNR three- to sevenfold superior to real PCT and noise reduction by a factor of 4-6 (p < 0.05). At 20 mAs, virtual PCT achieved diagnostic parametric maps, while the quality of real PCT maps was inadequate. At 10 mAs, both real and virtual PCT maps were nondiagnostic. Virtual PCT (but not real PCT) maps regained diagnostic quality at 10 mAs by applying 40 % adaptive statistical iterative reconstruction (ASIR) and improved further with 80 % ASIR. Our new method of creating virtual PCT by combining ultra-low-dose PCT with CTA information yields diagnostic perfusion parametric maps from PCT acquired at 20 or 10 mAs with 80 % ASIR. Effective dose is approximately 0.20 mSv, equivalent to two chest radiographs. (orig.)

Synthesis of polyphenylacetylene by radiation-induced polymerization in deoxycholic acid clathrate

International Nuclear Information System (INIS)

Cataldo, Franco; Strazzulla, Giovanni; Iglesias-Groth, Susana

2009-01-01

Phenylacetylene was polymerized as inclusion compound (clathrate) inside deoxycholic acid (DOCA) crystals. The polymerization was initiated by γ radiation and a total dose of 320 kGy was employed. The resulting polyphenylacetylene (PPA) was isolated by dissolution of deoxycholic acid in boiling ethanol. PPA high polymer was accompanied by a series of phenylacetylene oligomers, which were detected by liquid chromatographic analysis (HPLC). PPA was characterized by electronic absorption spectroscopy and by FT-IR spectroscopy in comparison to a reference PPA prepared by a stereospecific catalyst. The microstructure of PPA from inclusion polymerization was highly trans type, similar to that observed on PPA prepared by bulk radiolysis. No optical activity was detected by polarimetry on PPA prepared by inclusion polymerization. The host-guest complex PPA/DOCA was studied by differential thermal analysis (DTA) and by thermogravimetry (TGA). DTA provided evidences of the host-guest complex formation from the shift of the melting point of DOCA while the TGA confirmed the identity - in terms of thermal behaviour - of the PPA from inclusion polymerization with that from stereospecific polymerization

The use of 4D-CTA in the diagnostic work-up of brain arteriovenous malformations

Energy Technology Data Exchange (ETDEWEB)

Willems, Peter W.A. [Toronto Western Hospital, UHN, Division of Neuroradiology, Department of Medical Imaging, Toronto, Ontario (Canada); Leiden University Medical Center, Department of Radiology, Leiden (Netherlands); Taeshineetanakul, Patamintita; Terbrugge, Karel G.; Krings, Timo [Toronto Western Hospital, UHN, Division of Neuroradiology, Department of Medical Imaging, Toronto, Ontario (Canada); Schenk, Barry; Brouwer, Patrick A. [Leiden University Medical Center, Department of Radiology, Leiden (Netherlands)

2012-02-15

We aimed to evaluate the use of time-resolved whole-head CT angiography (4D-CTA) in patients with an untreated arteriovenous malformation of the brain (bAVM), as demonstrated by catheter angiography (DSA). Seventeen patients with a DSA-proven bAVM were enrolled. These were subjected to 4D-CTA imaging using a 320 detector row CT scanner. Using a standardized scoring sheet, all studies were analyzed by a panel of three readers. This panel was blind to the DSA results at the time of reading the 4D-CTA. 4D-CTA detected all bAVMs. With regard to the Spetzler-Martin grade, 4D-CTA disagreed with DSA in only one case, where deep venous drainage was missed. Further discrepancies between 4D-CTA and DSA analyses included underestimation of the nidus size in small lesions (four cases), misinterpretation of a feeding vessel (one case), misinterpretation of indirect feeding through pial collaterals (three cases) and oversight of mild arterial enlargement (two cases). 4D-CTA correctly distinguished low-flow from high-flow lesions and detected dural/transosseous feeding (one case), venous narrowing (one case) and venous pouches (nine cases). In this series, 4D-CTA was able to detect all bAVMs. Although some angioarchitectural details were missed or misinterpreted when compared to DSA, 4D-CTA evaluation was sufficiently accurate to diagnose the shunt and classify it. Moreover, 4D-CTA adds cross-sectional imaging and perfusion maps, helpful in treatment planning. 4D-CTA appears to be a valuable new adjunct in the non-invasive diagnostic work-up of bAVMs and their follow-up when managed conservatively. (orig.)

The use of 4D-CTA in the diagnostic work-up of brain arteriovenous malformations

International Nuclear Information System (INIS)

Willems, Peter W.A.; Taeshineetanakul, Patamintita; Terbrugge, Karel G.; Krings, Timo; Schenk, Barry; Brouwer, Patrick A.

2012-01-01

We aimed to evaluate the use of time-resolved whole-head CT angiography (4D-CTA) in patients with an untreated arteriovenous malformation of the brain (bAVM), as demonstrated by catheter angiography (DSA). Seventeen patients with a DSA-proven bAVM were enrolled. These were subjected to 4D-CTA imaging using a 320 detector row CT scanner. Using a standardized scoring sheet, all studies were analyzed by a panel of three readers. This panel was blind to the DSA results at the time of reading the 4D-CTA. 4D-CTA detected all bAVMs. With regard to the Spetzler-Martin grade, 4D-CTA disagreed with DSA in only one case, where deep venous drainage was missed. Further discrepancies between 4D-CTA and DSA analyses included underestimation of the nidus size in small lesions (four cases), misinterpretation of a feeding vessel (one case), misinterpretation of indirect feeding through pial collaterals (three cases) and oversight of mild arterial enlargement (two cases). 4D-CTA correctly distinguished low-flow from high-flow lesions and detected dural/transosseous feeding (one case), venous narrowing (one case) and venous pouches (nine cases). In this series, 4D-CTA was able to detect all bAVMs. Although some angioarchitectural details were missed or misinterpreted when compared to DSA, 4D-CTA evaluation was sufficiently accurate to diagnose the shunt and classify it. Moreover, 4D-CTA adds cross-sectional imaging and perfusion maps, helpful in treatment planning. 4D-CTA appears to be a valuable new adjunct in the non-invasive diagnostic work-up of bAVMs and their follow-up when managed conservatively. (orig.)

Three dimensional CT angiography (3D-CTA) in ruptured aneurysm surgery on acute stage

International Nuclear Information System (INIS)

Matsumoto, Masato; Endo, Yuji; Nakano, Masayuki

1998-01-01

We evaluated three-dimensional CT angiography (3D-CTA) for the treatment of acutely ruptured cerebral aneurysms. Sixty patients with subarachnoid hemorrhage from cerebral aneurysms were investigated both by 3D-CTA and conventional angiography and 26 patients were studied using 3D-CTA without conventional angiography. In the 60 cases, both 3D-CTA and the conventional angiography revealed 100% accuracy in diagnosing ruptured aneurysms, and 3D-CTA and the conventional angiography showed 96% and 92% accuracy for unruptured aneurysms respectively. 3D-CTA was equal or superior to the conventional angiography. Based on these data, since December, 1996, we have operated on 26 consecutive patients with ruptured aneurysms located in the anterior circulation of the circle of Willis, using 3D-CTA without conventional angiography. Thirty-one aneurysms, including 5 associated unruptured aneurysms, were visualized by 3D-CTA and verified at surgery. All aneurysms were clipped successfully. We think that it will be possible to operate on most ruptured aneurysms using only 3D-CTA without the conventional angiography except for the cases of the following situations: if a cerebral infarction is present, conventional angiography is required to evaluate for a stenotic or occlusive lesion of the intracranial arteries, cervical carotid, or vertebral arteries; in cases of giant or large aneurysms, the dynamic information provided by the conventional angiography is needed in case bypass surgery is necessary; and for aneurysms close to bony structures, such as an internal carotid-ophthalmic artery aneurysm, conventional angiography is necessary. (author)

Facile Synthesis of Well-Defined MDMO-PPV Containing (TriBlock—Copolymers via Controlled Radical Polymerization and CuAAC Conjugation

Directory of Open Access Journals (Sweden)

Neomy Zaquen

2015-02-01

Full Text Available A systematic investigation into the chain transfer polymerization of the so-called radical precursor polymerization of poly(p-phenylene vinylene (PPV materials is presented. Polymerizations are characterized by systematic variation of chain transfer agent (CTA concentration and reaction temperature. For the chain transfer constant, a negative activation energy of −12.8 kJ·mol−1 was deduced. Good control over molecular weight is achieved for both the sulfinyl and the dithiocarbamate route (DTC. PPVs with molecular weights ranging from thousands to ten thousands g·mol−1 were obtained. To allow for a meaningful analysis of the CTA influence, Mark–Houwink–Kuhn–Sakurada (MHKS parameters were determined for conjugated MDMO-PPV ([2-methoxy-5-(3',7'-dimethyloctyloxy]-1,4-phenylenevinylene to α = 0.809 and k = 0.00002 mL·g−1. Further, high-endgroup fidelity of the CBr4-derived PPVs was proven via chain extension experiments. MDMO-PPV-Br was successfully used as macroinitiator in atom transfer radical polymerization (ATRP with acrylates and styrene. A more polar PPV counterpart was chain extended by an acrylate in single-electron transfer living radical polymerization (SET-LRP. In a last step, copper-catalyzed azide alkyne cycloaddition (CuAAC was used to synthesize block copolymer structures. Direct azidation followed by macromolecular conjugation showed only partial success, while the successive chain extension via ATRP followed by CuAAC afforded triblock copolymers of the poly(p-phenylene vinylene-block-poly(tert-butyl acrylate-block-poly(ethylene glycol (PPV-b-PtBuA-b-PEG.

Assessment of the feasible CTA windows for efficient spacing with energy-neutral CDO

OpenAIRE

Dalmau Codina, Ramon; Prats Menéndez, Xavier

2016-01-01

Continuous descent operations (CDO) with con- trolled times of arrival (CTA) at one or several metering fixes could enable environmentally friendly procedures at the same time that terminal airspace capacity is not compromised. This paper focuses on CTA updates once the descent has been already initiated, assessing the feasible CTA window (and associated fuel consumption) of CDO requiring neither thrust nor speed-brake usage alon...

Robust Crosslinked Stereocomplexes and C60 Inclusion Complexes of Vinyl-Functionalized Stereoregular Polymers Derived from Chemo/Stereoselective Coordination Polymerization

KAUST Repository

Vidal, Fernando

2016-07-07

The successful synthesis of highly syndiotactic polar vinyl polymers bearing the reactive pendant vinyl group on each repeat unit, which is enabled by perfectly chemoselective and highly syndiospecific coordination polymerization of divinyl polar monomers developed through this work, has allowed the construction of robust crosslinked supramolecular stereocomplexes and C60 inclusion complexes. The metal-mediated coordination polymerization of three representative polar divinyl monomers, including vinyl methacrylate (VMA), allyl methacrylate (AMA), and N,N-diallyl acrylamide (DAA) by Cs-ligated zirconocenium ester enolate catalysts under ambient conditions exhibits complete chemoselectivity and high stereoselectivity, thus producing the corresponding vinyl-functionalized polymers with high (92% rr) to quantitative (>99% rr) syndiotacticity. A combined experimental (synthetic, kinetic, and mechanistic) and theoretical (DFT) investigation has yielded a unimetallic, enantiomorphic-site controlled propagation mechanism. Post-functionalization of the obtained syndiotactic vinyl-functionalized polymers via the thiol-ene click and photocuring reactions readily produced the corresponding thiolated polymers and flexible crosslinked thin film materials, respectively. Complexation of such syndiotactic vinyl-functionalized polymers with isotactic poly(methyl methacrylate) and fullerene C60 generates supramolecular crystalline helical stereocomplexes and inclusion complexes, respectively. Crosslinking of such complexes afforded robust crosslinked stereocomplexes that are solvent resistant and also exhibit considerably enhanced thermal and mechanical properties as compared to the uncrosslinked stereocompexes.

Robust Crosslinked Stereocomplexes and C60 Inclusion Complexes of Vinyl-Functionalized Stereoregular Polymers Derived from Chemo/Stereoselective Coordination Polymerization

KAUST Repository

Vidal, Fernando; Falivene, Laura; Caporaso, Lucia; Cavallo, Luigi; Chen, Eugene Y.-X.

2016-01-01

The successful synthesis of highly syndiotactic polar vinyl polymers bearing the reactive pendant vinyl group on each repeat unit, which is enabled by perfectly chemoselective and highly syndiospecific coordination polymerization of divinyl polar monomers developed through this work, has allowed the construction of robust crosslinked supramolecular stereocomplexes and C60 inclusion complexes. The metal-mediated coordination polymerization of three representative polar divinyl monomers, including vinyl methacrylate (VMA), allyl methacrylate (AMA), and N,N-diallyl acrylamide (DAA) by Cs-ligated zirconocenium ester enolate catalysts under ambient conditions exhibits complete chemoselectivity and high stereoselectivity, thus producing the corresponding vinyl-functionalized polymers with high (92% rr) to quantitative (>99% rr) syndiotacticity. A combined experimental (synthetic, kinetic, and mechanistic) and theoretical (DFT) investigation has yielded a unimetallic, enantiomorphic-site controlled propagation mechanism. Post-functionalization of the obtained syndiotactic vinyl-functionalized polymers via the thiol-ene click and photocuring reactions readily produced the corresponding thiolated polymers and flexible crosslinked thin film materials, respectively. Complexation of such syndiotactic vinyl-functionalized polymers with isotactic poly(methyl methacrylate) and fullerene C60 generates supramolecular crystalline helical stereocomplexes and inclusion complexes, respectively. Crosslinking of such complexes afforded robust crosslinked stereocomplexes that are solvent resistant and also exhibit considerably enhanced thermal and mechanical properties as compared to the uncrosslinked stereocompexes.

ITER CTA newsletter. No. 6

International Nuclear Information System (INIS)

2002-01-01

This ITER CTA Newsletter issue comprises information about the following ITER Meetings: The second negotiation meeting on the joint implementation of ITER, held in Tokyo(Japan) on 22-23 January 2002, and an international ITER symposium on burning plasma science and technology, held the day later after the second negotiation meeting at the same place

Predictive Value of CTA Spot Sign on Hematoma Expansion in Intracerebral Hemorrhage Patients

Directory of Open Access Journals (Sweden)

Wen-Jie Peng

2017-01-01

Full Text Available Hematoma expansion (HE occurs in approximately one-third of patients with intracerebral hemorrhage and leads to high rates of mortality and morbidity. Currently, contrast extravasation within hematoma, termed the spot sign on computed tomography angiography (CTA, has been identified as a strong independent predictor of early hematoma expansion. Past studies indicate that the spot sign is a dynamic entity and is indicative of active hemorrhage. Furthermore, to enhance the spot sign’s accuracy of predicting HE, spot parameters observed on CTA or dynamic CTA were used for its quantification. In addition, spot signs detected on multiphase CTA and dynamic CTA are shown to have higher sensitivity and specificity when compared with simple standardized spot sign detection in recent studies. Based on the spot sign, novel methods such as leakage sign and rate of contrast extravasation were explored to redefine HE prediction in combination with clinical characteristics and spot sign on CTA to assist clinical judgment. The spot sign is an accepted independent predictor of active hemorrhage and is used in both secondary intracerebral hemorrhage and the process of surgical assessment for hemorrhagic risk in patients with ischemic stroke. Spot sign predicts patients at high risk for hematoma expansion.

Locality-Aware CTA Clustering For Modern GPUs

Energy Technology Data Exchange (ETDEWEB)

Li, Ang; Song, Shuaiwen; Liu, Weifeng; Liu, Xu; Kumar, Akash; Corporaal, Henk

2017-04-08

In this paper, we proposed a novel clustering technique for tapping into the performance potential of a largely ignored type of locality: inter-CTA locality. We first demonstrated the capability of the existing GPU hardware to exploit such locality, both spatially and temporally, on L1 or L1/Tex unified cache. To verify the potential of this locality, we quantified its existence in a broad spectrum of applications and discussed its sources of origin. Based on these insights, we proposed the concept of CTA-Clustering and its associated software techniques. Finally, We evaluated these techniques on all modern generations of NVIDIA GPU architectures. The experimental results showed that our proposed clustering techniques could significantly improve on-chip cache performance.

Late Protein Synthesis-Dependent Phases in CTA Long-Term Memory: BDNF Requirement

Science.gov (United States)

Martínez-Moreno, Araceli; Rodríguez-Durán, Luis F.; Escobar, Martha L.

2011-01-01

It has been proposed that long-term memory (LTM) persistence requires a late protein synthesis-dependent phase, even many hours after memory acquisition. Brain-derived neurotrophic factor (BDNF) is an essential protein synthesis product that has emerged as one of the most potent molecular mediators for long-term synaptic plasticity. Studies in the rat hippocampus have been shown that BDNF is capable to rescue the late-phase of long-term potentiation as well as the hippocampus-related LTM when protein synthesis was inhibited. Our previous studies on the insular cortex (IC), a region of the temporal cortex implicated in the acquisition and storage of conditioned taste aversion (CTA), have demonstrated that intracortical delivery of BDNF reverses the deficit in CTA memory caused by the inhibition of IC protein synthesis due to anisomycin administration during early acquisition. In this work, we first analyze whether CTA memory storage is protein synthesis-dependent in different time windows. We observed that CTA memory become sensible to protein synthesis inhibition 5 and 7 h after acquisition. Then, we explore the effect of BDNF delivery (2 μg/2 μl per side) in the IC during those late protein synthesis-dependent phases. Our results show that BDNF reverses the CTA memory deficit produced by protein synthesis inhibition in both phases. These findings support the notion that recurrent rounds of consolidation-like events take place in the neocortex for maintenance of CTA memory trace and that BDNF is an essential component of these processes. PMID:21960964

Late protein synthesis-dependent phases in CTA long-term memory: BDNF requirement

Directory of Open Access Journals (Sweden)

Araceli eMartínez-Moreno

2011-09-01

Full Text Available It has been proposed that long-term memory persistence requires a late protein synthesis-dependent phase, even many hours after memory acquisition. Brain-derived neurotrophic factor (BDNF is an essential protein synthesis product that has emerged as one of the most potent molecular mediators for long-term synaptic plasticity. Studies in the rat hippocampus have been shown that BDNF is capable to rescue the late-phase of long-term potentiation as well as the hippocampus-related long-term memory when protein synthesis was inhibited. Our previous studies on the insular cortex (IC, a region of the temporal cortex implicated in the acquisition and storage of conditioned taste aversion (CTA, have demonstrated that intracortical delivery of BDNF reverses the deficit in CTA memory caused by the inhibition of IC protein synthesis due to anisomycin administration during early acquisition. In this work, we first analyze whether CTA memory storage is protein synthesis dependent in different time-windows. We observed that CTA memory become sensible to protein synthesis inhibition 5 and 7 hours after acquisition. Then, we explore the effect of BDNF delivery (2 μg/2 μl per side in the IC during those late protein synthesis-dependent phases. Our results show that BDNF reverses the CTA memory deficit produced by protein synthesis inhibition in both phases. These findings support the notion that recurrent rounds of consolidation-like events take place in the neocortex for maintenance of CTA memory trace and that BDNF is an essential component of these processes.

Late Protein Synthesis-Dependent Phases in CTA Long-Term Memory: BDNF Requirement.

Science.gov (United States)

Martínez-Moreno, Araceli; Rodríguez-Durán, Luis F; Escobar, Martha L

2011-01-01

It has been proposed that long-term memory (LTM) persistence requires a late protein synthesis-dependent phase, even many hours after memory acquisition. Brain-derived neurotrophic factor (BDNF) is an essential protein synthesis product that has emerged as one of the most potent molecular mediators for long-term synaptic plasticity. Studies in the rat hippocampus have been shown that BDNF is capable to rescue the late-phase of long-term potentiation as well as the hippocampus-related LTM when protein synthesis was inhibited. Our previous studies on the insular cortex (IC), a region of the temporal cortex implicated in the acquisition and storage of conditioned taste aversion (CTA), have demonstrated that intracortical delivery of BDNF reverses the deficit in CTA memory caused by the inhibition of IC protein synthesis due to anisomycin administration during early acquisition. In this work, we first analyze whether CTA memory storage is protein synthesis-dependent in different time windows. We observed that CTA memory become sensible to protein synthesis inhibition 5 and 7 h after acquisition. Then, we explore the effect of BDNF delivery (2 μg/2 μl per side) in the IC during those late protein synthesis-dependent phases. Our results show that BDNF reverses the CTA memory deficit produced by protein synthesis inhibition in both phases. These findings support the notion that recurrent rounds of consolidation-like events take place in the neocortex for maintenance of CTA memory trace and that BDNF is an essential component of these processes.

Improved Livingness and Control over Branching in RAFT Polymerization of Acrylates: Could Microflow Synthesis Make the Difference?

Science.gov (United States)

Derboven, Pieter; Van Steenberge, Paul H M; Vandenbergh, Joke; Reyniers, Marie-Francoise; Junkers, Thomas; D'hooge, Dagmar R; Marin, Guy B

2015-12-01

The superior capabilities of structured microreactors over batch reactors are demonstrated for reversible addition-fragmentation chain transfer (RAFT) solution polymerization of n-butyl acrylate with the aid of simulations, explicitly accounting for the chain length distribution of all macrospecies types. Since perfect isothermicity can be established in a microreactor, less side products due to backbiting and β-scission are formed compared to the batch operation in which ineffective heat removal leads to an undesirable temperature spike. For a given RAFT chain transfer agent (CTA), additional microstructural control results under microflow conditions by optimizing the reaction temperature, lowering the dilution degree, or decreasing the initial molar ratio of monomer to RAFT CTA. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

CaMKII Requirement for in Vivo Insular Cortex LTP Maintenance and CTA Memory Persistence

Directory of Open Access Journals (Sweden)

Yectivani Juárez-Muñoz

2017-11-01

Full Text Available Calcium-calmodulin/dependent protein kinase II (CaMKII plays an essential role in LTP induction, but since it has the capacity to remain persistently activated even after the decay of external stimuli it has been proposed that it can also be necessary for LTP maintenance and therefore for memory persistence. It has been shown that basolateral amygdaloid nucleus (Bla stimulation induces long-term potentiation (LTP in the insular cortex (IC, a neocortical region implicated in the acquisition and retention of conditioned taste aversion (CTA. Our previous studies have demonstrated that induction of LTP in the Bla-IC pathway before CTA training increased the retention of this task. Although it is known that IC-LTP induction and CTA consolidation share similar molecular mechanisms, little is known about the molecular actors that underlie their maintenance. The purpose of the present study was to evaluate the role of CaMKII in the maintenance of in vivo Bla-IC LTP as well as in the persistence of CTA long-term memory (LTM. Our results show that acute microinfusion of myr-CaMKIINtide, a selective inhibitor of CaMKII, in the IC of adult rats during the late-phase of in vivo Bla-IC LTP blocked its maintenance. Moreover, the intracortical inhibition of CaMKII 24 h after CTA acquisition impairs CTA-LTM persistence. Together these results indicate that CaMKII is a central key component for the maintenance of neocortical synaptic plasticity as well as for persistence of CTA-LTM.

Sensitivity of CTA to dark matter signals from the Galactic Center

Energy Technology Data Exchange (ETDEWEB)

Pierre, Mathias [Département Physique, École Normale Supérieure de Cachan, 61 Avenue du Président Wilson, Cachan, 94230 France (France); Siegal-Gaskins, Jennifer M. [California Institute of Technology, 1200 E. California Blvd., Pasadena, CA, 91125 (United States); Scott, Pat, E-mail: mathias.pierre@ens-cachan.fr, E-mail: jsg@tapir.caltech.edu, E-mail: patscott@physics.mcgill.ca [Department of Physics, McGill University, 3600 Rue University, Montréal, Québec, H3A 2T8 Canada (Canada)

2014-06-01

The Galactic Center is one of the most promising targets for indirect detection of dark matter with gamma rays. We investigate the sensitivity of the upcoming Cherenkov Telescope Array (CTA) to dark matter annihilation and decay in the Galactic Center. As the inner density profile of the Milky Way's dark matter halo is uncertain, we study the impact of the slope of the Galactic density profile, inwards of the Sun, on the prospects for detecting a dark matter signal with CTA. Adopting the Ring Method to define the signal and background regions in an ON-OFF analysis approach, we find that the sensitivity achieved by CTA to annihilation signals is strongly dependent on the inner profile slope, whereas the dependence is more mild in the case of dark matter decay. Surprisingly, we find that the optimal choice of signal and background regions is virtually independent of the assumed density profile. For the fiducial case of a Navarro-Frenk-White profile, we find that CTA will be able to probe annihilation cross-sections well below the canonical thermal relic value for dark matter masses from a few tens of GeV up to ∼ 5 TeV for annihilation to τ{sup +}τ{sup −}, and will achieve only a slightly weaker sensitivity for annihilation to b b-bar or μ{sup +}μ{sup −}. CTA will improve significantly on current sensitivity to annihilation signals for dark matter masses above ∼ 100 GeV, covering parameter space that is complementary to that probed by searches with the Fermi Large Area Telescope. The interpretation of apparent excesses in the measured cosmic-ray electron and positron spectra as signals of dark matter decay will also be testable with CTA observations of the Galactic Center. We demonstrate that both for annihilation and for decay, including spectral information for hard channels (such as μ{sup +}μ{sup −} and τ{sup +}τ{sup −}) leads to enhanced sensitivity for dark matter masses above m{sub DM} ∼ 200 GeV.

Sensitivity of CTA to dark matter signals from the Galactic Center

International Nuclear Information System (INIS)

Pierre, Mathias; Siegal-Gaskins, Jennifer M.; Scott, Pat

2014-01-01

The Galactic Center is one of the most promising targets for indirect detection of dark matter with gamma rays. We investigate the sensitivity of the upcoming Cherenkov Telescope Array (CTA) to dark matter annihilation and decay in the Galactic Center. As the inner density profile of the Milky Way's dark matter halo is uncertain, we study the impact of the slope of the Galactic density profile, inwards of the Sun, on the prospects for detecting a dark matter signal with CTA. Adopting the Ring Method to define the signal and background regions in an ON-OFF analysis approach, we find that the sensitivity achieved by CTA to annihilation signals is strongly dependent on the inner profile slope, whereas the dependence is more mild in the case of dark matter decay. Surprisingly, we find that the optimal choice of signal and background regions is virtually independent of the assumed density profile. For the fiducial case of a Navarro-Frenk-White profile, we find that CTA will be able to probe annihilation cross-sections well below the canonical thermal relic value for dark matter masses from a few tens of GeV up to ∼ 5 TeV for annihilation to τ + τ − , and will achieve only a slightly weaker sensitivity for annihilation to b b-bar or μ + μ − . CTA will improve significantly on current sensitivity to annihilation signals for dark matter masses above ∼ 100 GeV, covering parameter space that is complementary to that probed by searches with the Fermi Large Area Telescope. The interpretation of apparent excesses in the measured cosmic-ray electron and positron spectra as signals of dark matter decay will also be testable with CTA observations of the Galactic Center. We demonstrate that both for annihilation and for decay, including spectral information for hard channels (such as μ + μ − and τ + τ − ) leads to enhanced sensitivity for dark matter masses above m DM ∼ 200 GeV

DIRAC framework evaluation for the Fermi-LAT and CTA experiments

International Nuclear Information System (INIS)

Arrabito, L; Cohen-Tanugi, J; Piron, F; Renaud, M; Rolland, V; Diaz, R Graciani; Longo, F; Kuss, M; Sapunov, M; Tsaregorodtsev, A; Zimmer, S

2014-01-01

DIRAC (Distributed Infrastructure with Remote Agent Control) is a general framework for the management of tasks over distributed heterogeneous computing environments. It has been originally developed to support the production activities of the LHCb (Large Hadron Collider Beauty) experiment and today is extensively used by several particle physics and biology communities. Current (Fermi Large Area Telescope – LAT) and planned (Cherenkov Telescope Array – CTA) new generation astrophysical/cosmological experiments, with very large processing and storage needs, are currently investigating the usability of DIRAC in this context. Each of these use cases has some peculiarities: Fermi-LAT will interface DIRAC to its own workflow system to allow the access to the grid resources, while CTA is using DIRAC as workflow management system for Monte Carlo production and analysis on the grid. We describe the prototype effort that we lead toward deploying a DIRAC solution for some aspects of Fermi-LAT and CTA needs.

Final ITER CTA project board meeting

International Nuclear Information System (INIS)

Vlasenkov, V.

2003-01-01

The final ITER CTA Project Board Meeting (PB) took place in Barcelona, Spain on 8 December 2002. The PB took notes of the comments concerning the status of the International Team and the Participants Teams, including Dr. Aymar's report 'From ITER to a FUSION Power Reactor' and the assessment of the ITER project cost estimate

Dosimetric response of united, commercially available CTA foils for 60Co gamma rays

International Nuclear Information System (INIS)

Peimel-Stuglik, Z.

2001-01-01

The usefulness of two kinds of untinted CTA foils: Fuji CTR-125 dosimetric foil and technical CTA-T foil, produced by 'Zaklady Chemiczne, 'Gorzow Wielkopolski' as support for light-sensitive layers of amateur photo-films, for 60 Co gamma ray dosimetry was investigated. In spite of rather bad physical parameters of the technical foil (spread of foil thickness, high and different initial absorbance) the dosimetric response of both foils for 60 Co gamma rays was similar. The CTA-T foil can be used for routine dosimetry providing that dosimetric signals have to be calculated exactly as recommended by the ASTM (American Society for Testing and Materials) standard, i.e. as the difference of absorbance of irradiated and (the same) non-irradiated foil. Any other approach may lead to high errors of dose evaluation. The last is true also for other CTA foils, especially after long self-life. (author)

Polymer Inclusion Membrane Containing a Tripodal Diglycolamide Ligand: Actinide Ion Uptake and Transport Studies

NARCIS (Netherlands)

Mahanty, B.; Mohapatra, P.K.; Raut, D.R.; Das, D.K.; Behere, P.G.; Afzal, M.; Verboom, Willem

2016-01-01

A cellulose triacetate (CTA)-based polymer inclusion membrane (PIM) containing a C-pivot tripodal diglycolamide (T-DGA) as the carrier extractant and 2-nitrophenyl octyl ether (NPOE) as the plasticizer shows potential for the uptake of actinides from acidic feed solutions. The uptake of actinides

The High-Level Interface Definitions in the ASTRI/CTA Mini Array Software System (MASS)

Science.gov (United States)

Conforti, V.; Tosti, G.; Schwarz, J.; Bruno, P.; Cefal‘A, M.; Paola, A. D.; Gianotti, F.; Grillo, A.; Russo, F.; Tanci, C.; Testa, V.; Antonelli, L. A.; Canestrari, R.; Catalano, O.; Fiorini, M.; Gallozzi, S.; Giro, E.; Palombara, N. L.; Leto, G.; Maccarone, M. C.; Pareschi, G.; Stringhetti, L.; Trifoglio, M.; Vercellone, S.; Astri Collaboration; Cta Consortium

2015-09-01

ASTRI (Astrofisica con Specchi a Tecnologia Replicante Italiana) is a Flagship Project funded by the Italian Ministry of Education, University and Research, and led by INAF, the Italian National Institute of Astrophysics. Within this framework, INAF is currently developing an end-to-end prototype, named ASTRI SST-2M, of a Small Size Dual-Mirror Telescope for the Cherenkov Telescope Array, CTA. A second goal of the project is the realization of the ASTRI/CTA mini-array, which will be composed of seven SST-2M telescopes placed at the CTA Southern Site. The ASTRI Mini Array Software System (MASS) is designed to support the ASTRI/CTA mini-array operations. MASS is being built on top of the ALMA Common Software (ACS) framework, which provides support for the implementation of distributed data acquisition and control systems, and functionality for log and alarm management, message driven communication and hardware devices management. The first version of the MASS system, which will comply with the CTA requirements and guidelines, will be tested on the ASTRI SST-2M prototype. In this contribution we present the interface definitions of the MASS high level components in charge of the ASTRI SST-2M observation scheduling, telescope control and monitoring, and data taking. Particular emphasis is given to their potential reuse for the ASTRI/CTA mini-array.

3D/3D registration of coronary CTA and biplane XA reconstructions for improved image guidance

Energy Technology Data Exchange (ETDEWEB)

Dibildox, Gerardo, E-mail: g.dibildox@erasmusmc.nl; Baka, Nora; Walsum, Theo van [Biomedical Imaging Group Rotterdam, Departments of Radiology and Medical Informatics, Erasmus Medical Center, 3015 GE Rotterdam (Netherlands); Punt, Mark; Aben, Jean-Paul [Pie Medical Imaging, 6227 AJ Maastricht (Netherlands); Schultz, Carl [Department of Cardiology, Erasmus Medical Center, 3015 GE Rotterdam (Netherlands); Niessen, Wiro [Quantitative Imaging Group, Faculty of Applied Sciences, Delft University of Technology, 2628 CJ Delft, The Netherlands and Biomedical Imaging Group Rotterdam, Departments of Radiology and Medical Informatics, Erasmus Medical Center, 3015 GE Rotterdam (Netherlands)

2014-09-15

Purpose: The authors aim to improve image guidance during percutaneous coronary interventions of chronic total occlusions (CTO) by providing information obtained from computed tomography angiography (CTA) to the cardiac interventionist. To this end, the authors investigate a method to register a 3D CTA model to biplane reconstructions. Methods: The authors developed a method for registering preoperative coronary CTA with intraoperative biplane x-ray angiography (XA) images via 3D models of the coronary arteries. The models are extracted from the CTA and biplane XA images, and are temporally aligned based on CTA reconstruction phase and XA ECG signals. Rigid spatial alignment is achieved with a robust probabilistic point set registration approach using Gaussian mixture models (GMMs). This approach is extended by including orientation in the Gaussian mixtures and by weighting bifurcation points. The method is evaluated on retrospectively acquired coronary CTA datasets of 23 CTO patients for which biplane XA images are available. Results: The Gaussian mixture model approach achieved a median registration accuracy of 1.7 mm. The extended GMM approach including orientation was not significantly different (P > 0.1) but did improve robustness with regards to the initialization of the 3D models. Conclusions: The authors demonstrated that the GMM approach can effectively be applied to register CTA to biplane XA images for the purpose of improving image guidance in percutaneous coronary interventions.

Polymer Inclusion Membranes with Strip Dispersion

Directory of Open Access Journals (Sweden)

Yueh-Hsien Li

2017-06-01

Full Text Available The present work investigated the permeation of indium ions through a polymer inclusion membrane (PIM, prepared with cellulose triacetate (CTA as the base polymer, tris(2-butoxyethyl phosphate (TBEP as the plasticizer and di-(2-ethylhexylphosphoric acid (D2EHPA as the extractant. With 5 M HCl aqueous solution as the strip solution, we observed an initial indium permeability of 2.4 × 10−4 m/min. However, the permeability decreases with time, dropping to about 3.4 × 10−5 m/min after 200 min of operation. Evidence was obtained showing that hydrolysis of CTA occurred, causing a dramatic decrease in the feed pH (protons transported from strip to feed solutions and a loss of extractant and plasticizer from the membrane, and then leading to the loss of indium permeability. To alleviate the problem of hydrolysis, we proposed an operation scheme called polymer inclusion membranes with strip dispersion: dispersing the strip solution in extractant-containing oil and then bringing the dispersion to contact with the polymer membrane. Since the strong acid was dispersed in oil, the membrane did not directly contact the strong acid at all times, and membrane hydrolysis was thus alleviated and the loss of indium permeability was effectively prevented. With the proposed scheme, a stable indium permeability of 2.5 × 10−4 m/min was obtained during the whole time period of the permeation experiment.

Imaging anatomy of dorsal pancreatic artery in patients with diabetes: a comparative study between CTA and DSA

International Nuclear Information System (INIS)

Lin Yuning; Li Hui; Yang Xizhang; Chen Ziqian; Tan Jianming; Zhong Qun; Yang Li; Wu Zhixian; Li Huimin; Huang Yisheng

2011-01-01

Objective: To investigate the clinical value of 64-section CT angiography (CTA) in detecting the origin of dorsal pancreatic artery (DPA). Methods: Ninety-seven consecutive patients with diabetes received transcatheter infusion of autologous bone marrow-derived stem cell transplantation into DPA. Abdominal CTA was performed in 42 patients before angiography. Celiac trunk, splenic, common hepatic and superior mesenteric arteries were reconstructed in order to locate the origin and traveling course of DPA. A routine angiography of both celiac and superior mesenteric arteries was performed for the demonstration of DPA. Further angiography of splenic and gastroduodenal arteries was carried out if necessary. Taking DSA images as the reference standard, the sensitivity, specificity and accuracy of CTA for DPA detection were calculated. Results: DPA was the main supply artery of pancreas in 85.7% patients (36/42). CTA demonstrated the origin of DPA in 35 cases, although one of which was confirmed to be misjudged (false positive). In seven cases CTA could not demonstrate DPA, and DSA proved that 2 of them was misjudged (false negative). The sensitivity,specificity and accuracy of CTA for DPA detection were 94.4%, 83.3% and 92.9%, respectively. Conclusion: 64-section CTA can accurately detect the origin of main supply artery of pancreas, which is of great value in guiding the interventional procedure for pancreatic diseases. (authors)

Hexadecyltrimethylammonium bromide (CTA-Br) and 1-butyl-3-methylimidazolium tetrafluoroborate (bmim-BF4) in aqueous solution: An ephemeral binary system.

Science.gov (United States)

Comelles, Francesc; Ribosa, Isabel; Gonzalez, Juan José; Garcia, M Teresa

2017-03-15

Mixtures of the cationic surfactant hexadecyltrimethylammonium bromide (CTA-Br) and the ionic liquid 1-butyl-3-methylimidazolium tetrafluoroborate (bmim-BF 4 ) in aqueous solutions are expected to behave as typical binary cationic surfactant system taking into account the surface activity displayed by the ionic liquid, instead of considering the IL as a water cosolvent. Surface tension and conductivity measurements have been conducted as a function of the total concentration of the mixtures at different surfactant mole fraction (α CTA-Br ) to investigate the surface active properties. Turbidity immediately appearing when the compounds are mixed in water suggests the spontaneous formation of the low soluble compound hexadecyltrimethylammonium tetrafluoroborate (CTA-BF 4 ), together with the salt formed by the respective counterions bmim + and Br - in solution. For α CTA-Br ≠0.5, furthermore of the mentioned compounds, the spare bmim-BF 4 (for α CTA-Br Br (for α CTA-Br >0.5), are also present in the aqueous solution. Systems containing excess of bmim-BF 4 show a low critical aggregate concentration (cac), but an unexpected high surface tension at cac (γ cac ≈53-56mN/m), as pure CTA-BF 4 . For systems containing excess of CTA-Br, cac increases but γ cac decreases up to 36mN/m. Mixtures of pure CTA-BF 4 and bmim-BF 4 or CTA-Br behave as typical binary surfactant systems. Copyright © 2016 Elsevier Inc. All rights reserved.

Demonstration of the dorsal pancreatic artery by CTA to facilitate superselective arterial infusion of stem cells into the pancreas

International Nuclear Information System (INIS)

Lin Yuning; Yang Xizhang; Chen Ziqian; Tan Jianming; Zhong Qun; Yang Li; Wu Zhixian

2012-01-01

Purpose: To investigate the diagnostic performance of 64-section CTA in the detection of dorsal pancreatic artery before interventional therapy for patients with diabetes. Materials and methods: The study was approved by the institutional ethics committee; written informed consent was obtained. Forty-two consecutive patients with diabetes received an experimental treatment of autologous bone marrow-derived stem cell transplantation by means of infusion into the dorsal pancreatic artery. All cases underwent abdominal CTA before angiography of pancreatic arteries in order to locate the origin and course of dorsal pancreatic artery. Angiography of coeliac artery, splenic artery, common hepatic artery and superior mesenteric artery were performed both in CTA and DSA. Superselective catheterization of dorsal pancreatic artery was carried out for the infusion of stem cell. Sensitivity, specificity and accuracy for the detection of dorsal pancreatic artery with CTA were calculated using DSA images as the reference standard. Results: Thirty-five and thirty-six dorsal pancreatic arteries were detected by CTA and DSA respectively. Dorsal pancreatic artery was not visualized in either CTA or DSA in 5 patients. The sensitivity, specificity and accuracy for CTA were 94.4%, 83.3% and 92.9%. Conclusion: 64-section CTA is accurate for the detection of dorsal pancreatic artery. It may be useful for the facilitation of superselective arterial infusion of stem cells to pancreas.

Mast cells contribute to the mucosal adjuvant effect of CTA1-DD after IgG-complex formation.

Science.gov (United States)

Fang, Yu; Larsson, Lisa; Mattsson, Johan; Lycke, Nils; Xiang, Zou

2010-09-01

Mast cell activation is one of the most dramatic immune-mediated responses the body can encounter. In the worst scenario (i.e., anaphylaxis), this response is fatal. However, the importance of mast cells as initiators and effectors of both innate and adaptive immunity in healthy individuals has recently been appreciated. It was reported that mast cell activation can be used as an adjuvant to promote Ag-specific humoral immune responses upon vaccination. In this study, we have used a clinically relevant mucosal adjuvant, cholera toxin A1 subunit (CTA1)-DD, which is a fusion protein composed of CTA1, the ADP-ribosylating part of cholera toxin, and DD, two Ig-binding domains derived from Staphylococcus aureus protein A. CTA1-DD in combination with polyclonal IgG induced degranulation and production of TNF-alpha from mouse mast cells. Furthermore, CTA1-DD and polyclonal IgG complex induced mast cell degranulation in mouse skin tissue and nasal mucosa. We also found that intranasal immunization with hapten (4-hydroxy-3-nitrophenyl) acetyl (NP) coupled to chicken gammaglobulin admixed with CTA1-DD complexed with polyclonal IgG greatly enhanced serum IgG anti-NP Ab responses and stimulated higher numbers of NP-specific plasma cells in the bone marrow as compared with that observed in mice immunized with NP-chicken gammaglobulin with CTA1-DD alone. This CTA1-DD/IgG complex-mediated enhancement was mast cell dependent because it was absent in mast cell-deficient Kit(W-sh/W-sh) mice. In conclusion, our data suggest that a clinically relevant adjuvant, CTA1-DD, exerts additional augmenting effects through activation of mucosal mast cells, clearly demonstrating that mast cells could be further exploited for improving the efficacy of mucosal vaccines.

Comparison of the clinical efficacy of craniotomy and craniopuncture therapy for the early stage of moderate volume spontaneous intracerebral haemorrhage in basal ganglia: Using the CTA spot sign as an entry criterion.

Science.gov (United States)

Ge, Chunyan; Zhao, Wangmiao; Guo, Hong; Sun, Zhaosheng; Zhang, Wanzeng; Li, Xiaowei; Yang, Xuehui; Zhang, Jinrong; Wang, Dongxin; Xiang, Yi; Mao, Jianhui; Zhang, Wenchao; Guo, Hao; Zhang, Yazhao; Chen, Jianchao

2018-06-01

Surgical treatment is widely used for haematoma removal in spontaneous intracerebral haemorrhage (ICH) patients, but there is controversy about the selection of surgical methods. The CT angiography (CTA) spot sign has been proven to be a promising factor predicting haematoma expansion and is recommended as an entry criterion for haemostatic therapy in patients with ICH. This trial was designed to evaluate the clinical efficacy of two surgical methods (haematoma removal by craniotomy and craniopuncture combined with urokinase infusion) for patients in the early stage (≤6h from symptom onset) of spontaneous ICH with a moderate haematoma volume (30 ml - 60 ml). From January 2012 to July 2017, 196 eligible patients treated in our institution were enrolled according to the inclusion criteria. The patients were divided into the CTA spot sign positive type and CTA spot sign negative type according to the presence or absence of the CTA spot sign. For each type, the patients were randomly assigned to two groups, i.e., the craniotomy group, in which patients underwent craniotomy with haematoma removal, and the craniopuncture group, in which patients underwent minimally invasive craniopuncture combined with urokinase infusion therapy. Neurological function was evaluated with the Scandinavian Stroke Scale (SSS) at day 14. The disability level and the activities of daily living were assessed using a modified Rankin Scale (mRS) and Barthel Index (BI) at day 90. Case fatalities were recorded at day 14 and 90. Complications were recorded during hospitalization. For the CTA spot sign positive type, the craniotomy group had a higher SSS than that in the craniopuncture group (P spot sign negative type, there were no significant differences in the SSS, mRS, BI, fatality rate and complication rate between the two groups. ICH can be divided into the CTA spot sign positive and negative type according to the presence or absence of the CTA spot sign. For the CTA spot sign

Absence of Protoheme IX Farnesyltransferase CtaB Causes Virulence Attenuation but Enhances Pigment Production and Persister Survival in MRSA.

Science.gov (United States)

Xu, Tao; Han, Jian; Zhang, Jia; Chen, Jiazhen; Wu, Nan; Zhang, Wenhong; Zhang, Ying

2016-01-01

The membrane protein CtaB in S. aureus is a protoheme IX farnesyltransferase involved in the synthesis of the heme containing terminal oxidases of bacterial respiratory chain. In this study, to assess the role of CtaB in S. aureus virulence, pigment production, and persister formation, we constructed a ctaB mutant in the methicillin-resistant Staphylococcus aureus (MRSA) strain USA500. We found that deletion of ctaB attenuated growth and virulence in mice but enhanced pigment production and formation of quinolone tolerant persister cells in stationary phase. RNA-seq analysis showed that deletion of ctaB caused decreased transcription of several virulence genes including RNAIII which is consistent with its virulence attenuation. In addition, transcription of 20 ribosomal genes and 24 genes involved in amino acid biosynthesis was significantly down-regulated in the ctaB knockout mutant compared with the parent strain. These findings suggest the importance of heme biosynthesis in virulence and persister formation of S. aureus .

ITER CTA newsletter. No. 10

International Nuclear Information System (INIS)

2002-07-01

This ITER CTA newsletter issue comprises the ITER backgrounder, which was approved as an official document by the participants in the Negotiations on the ITER Implementation agreement at their fourth meeting, held in Cadarache from 4-6 June 2002, and information about two ITER meetings: one is the third meeting of the ITER parties' designated Safety Representatives, which took place in Cadarache, France from 6-7 June 2002, and the other is the second meeting of the International Tokamak Physics Activity (ITPA) topical group on diagnostics, which was held at General Atomics, San Diego, USA, from 4-8 March 2002

Comparison of CTA and Textual Feedback in Usability Testing for Malaysian Users

DEFF Research Database (Denmark)

Sivaji, Ashok; Clemmensen, Torkil; Nielsen, Søren Feodor

Usability moderators found that the concurrent think-aloud (CTA) method has some cultural limitation that impacts usability testing with Malaysian users. This gives rise to proposing a new method called textual feedback. The research question is to determine whether there are any differences...... in usability defects from the concurrent think-aloud (CTA) method (Condition 2) and textual feedback method (Condition 1) within the same group of Malaysian users. A pair-wise t-test was used, whereby users were subjected to performing usability task using both methods. Results reveal that we can reject...

Phase measuring deflectometry. An improved setup for measuring CTA mirror facets

Energy Technology Data Exchange (ETDEWEB)

Specovius, Andreas; Eldik, Christopher van; Woernlein, Andre; Ziegler, Alexander [Erlangen Centre for Astroparticle Physics (ECAP) (Germany)

2016-07-01

The future Cherenkov Telescope Array (CTA) will consist of up to 100 single telescopes with a total reflecting surface of ∝10.000 m{sup 2} made of numerous mirror facets. Characterizing the surface properties of these facets is quite challenging concerning time and logistics. An efficient way to reliably reconstruct the surface of specular free-forms is Phase Measuring Deflectometry (PMD). PMD is routinely used to characterize the focal distance and point spread function of spherical CTA prototype mirrors. To address the possibility to measure the surface properties of aspherical mirrors, a new PMD setup has recently been built. First experience with this setup is reported.

ITER CTA newsletter. No. 11, August 2002

International Nuclear Information System (INIS)

2002-10-01

This ITER CTA Newsletter issue includes conclusions of the Fusion Fast Track experts meeting held on 27 November 2001, which were presented to the European Research Council. The term 'Fast Track' has its origin in an initiative taken by the Belgian Presidency of the European Research Council to investigate whether it might be possible to accelerate the development of fusion, setting a goal for thermonuclear energy production with 20-30 years

Anatomy-based automatic detection and segmentation of major vessels in thoracic CTA images

International Nuclear Information System (INIS)

Zou Xiaotao; Liang Jianming; Wolf, M.; Salganicoff, M.; Krishnan, A.; Nadich, D.P.

2007-01-01

Existing approaches for automated computerized detection of pulmonary embolism (PE) using computed tomography angiography (CTA) usually focus on segmental and sub-segmental emboli. The goal of our current research is to extend our existing approach to automated detection of central PE. In order to detect central emboli, the major vessels must be first identified and segmented automatically. This submission presents an anatomy-based method for automatic computerized detection and segmentation of aortas and main pulmonary arteries in CTA images. (orig.)

Dosimetric response of united, commercially available CTA foils for sup 6 sup 0 Co gamma rays

CERN Document Server

Peimel-Stuglik, Z

2001-01-01

The usefulness of two kinds of untinted CTA foils: Fuji CTR-125 dosimetric foil and technical CTA-T foil, produced by 'Zaklady Chemiczne, 'Gorzow Wielkopolski' as support for light-sensitive layers of amateur photo-films, for sup 6 sup 0 Co gamma ray dosimetry was investigated. In spite of rather bad physical parameters of the technical foil (spread of foil thickness, high and different initial absorbance) the dosimetric response of both foils for sup 6 sup 0 Co gamma rays was similar. The CTA-T foil can be used for routine dosimetry providing that dosimetric signals have to be calculated exactly as recommended by the ASTM (American Society for Testing and Materials) standard, i.e. as the difference of absorbance of irradiated and (the same) non-irradiated foil. Any other approach may lead to high errors of dose evaluation. The last is true also for other CTA foils, especially after long self-life.

Compilation of the nuclear codes available in CTA

International Nuclear Information System (INIS)

D'Oliveira, A.B.; Moura Neto, C. de; Amorim, E.S. do; Ferreira, W.J.

1979-07-01

The present work is a compilation of some nuclear codes available in the Divisao de Estudos Avancados of the Instituto de Atividades Espaciais, (EAV/IAE/CTA). The codes are organized as the classification given by the Argonne National Laboratory. In each code are given: author, institution of origin, abstract, programming language and existent bibliography. (Author) [pt

Minimally invasive vascular imaging using 3D-CTA and 3D-MRA. Update

International Nuclear Information System (INIS)

Hayashi, Hiromitsu; Kawamata, Hiroshi; Takagi, Ryo; Amano, Yasuo; Wakabayashi, Hiroyuki; Ichikawa, Kazuo; Kumazaki, Tatsuo

1998-01-01

Conventional angiography is considered the standard of reference for diagnostic imaging of vascular diseases with respect to its temporal and spatial resolution. This procedure, however is invasive and repeated studies are difficult, and arterial complications are occasionally associated in catheter-based conventional angiography. Recent advances in diagnostic imaging have facilitated three-dimensional CT angiography (3D-CTA) using the volumetric acquisition capabilities inherent in spiral CT and three-dimensional MR angiography (3D-MRA) using the 3D gradient-echo sequence with a bolus injection of Gd-DTPA. These techniques can provide vascular images exceedingly similar to conventional angiograms within a short acquisition time. 3D-CTA and 3D-MRA are considered to be promising, minimally invasive methods for obtaining images of the vasculature, and alternatives to catheter angiography. This study reviews the current status of 3D-CTA and 3D-MRA, with emphasis on the clinical usefulness of three-dimensional diagnostic imaging for the evaluation of diverse vascular pathologies. (author)

Diagnostic accuracy of CTA and MRI/MRA in the evaluation of the cortical venous reflux in the intracranial dural arteriovenous fistula DAVF

Energy Technology Data Exchange (ETDEWEB)

Lin, Yen-Heng [National Taiwan University, Department of Medical Imaging and Radiology, Hospital and Medical College, Taipei (China); National Taiwan University Hospital, Department of Medical Imaging, Douliu City (China); Wang, Yu-Fen; Lee, Chung-Wei; Chen, Ya-Fang [National Taiwan University, Department of Medical Imaging and Radiology, Hospital and Medical College, Taipei (China); Liu, Hon-Man [National Taiwan University, Department of Medical Imaging and Radiology, Hospital and Medical College, Taipei (China); Fu Jen Catholic University, Department of Medical Imaging and Radiology, Hospital and Medical College, New Taipei City (China); Fu Jen Catholic University Hospital, Department of Medical Imaging, New Taipei City (China); Hsieh, Hong-Jen [National Taiwan University Hospital, Department of Medical Imaging, Douliu City (China)

2018-01-15

Computed tomography angiography (CTA) and magnetic resonance imaging/angiography (MRI/MRA) are used for the diagnosis of intracranial dural arteriovenous fistulas (DAVFs). The purpose of this study was to compare the diagnostic accuracy of CTA and magnetic resonance imaging/angiography (MRI/MRA) for detection of cortical venous reflux (CVR) in intracranial DAVFs. The records of patients with angiography-confirmed intracranial DAVFs who also received CTA and MRI/MRA from January 2008 to July 2016 were reviewed. CTA and MRI/MRA were reviewed for signs of CVR, and the diagnostic accuracy of individual signs was evaluated by receiver operating curve (ROC) analysis. A total 108 patients were included in this study. CTA signs of CVR included abnormal dilatation, early enhancement, and the presence of a medullary or pial vein. MRI/MRA signs of CVR included abnormal dilatation, early enhancement, flow-related enhancement, flow void, and medullary or pial venous collaterals. The sensitivity of individual CTA signs ranged from 62 to 96%, and specificities from 79 to 94%. The sensitivities of individual MRI/MRA signs ranged from 58 to 83%, and specificities from 77 to 93%. The area under ROC curve (AUC) of CTA and MRI/MRA were 0.91 and 0.87, respectively (P = 0.04 in direct comparison). In subgroup analysis, CTA had better diagnostic accuracy for higher grade disease (P = 0.05) and non-aggressive manifestation (P = 0.04). Both CTA and MRI/MRA have good diagnostic accuracy for detection of CVR in patients with intracranial DAVFs. There is modest evidence that CTA is better than MRI/MRA. (orig.)

Meeting of the ITER CTA Project Board

International Nuclear Information System (INIS)

Vlasenkov, V.

2002-01-01

The meeting of the ITER CTA Project Board (PB) took place in Toronto, Canada on 16 September 2002 on the occasion of the fifth Negotiations Meeting (N-5). Thirteen participants, PB members and experts from Canada, EU, Japan, RF and the International Team (IT) attended the meeting chaired by Acad. E. Velikhov. PB heard progress reports of the participating parties and the comments concerning the status of participants team (PT) and the IT were presented

Controlled release of ethylene via polymeric films for food packaging

Science.gov (United States)

Pisano, Roberto; Bazzano, Marco; Capozzi, Luigi Carlo; Ferri, Ada; Sangermano, Marco

2015-12-01

In modern fruit supply chain a common method to trigger ripening is to keep fruits inside special chambers and initiate the ripening process through administration of ethylene. Ethylene is usually administered through cylinders with inadequate control of its final concentration in the chamber. The aim of this study is the development of a new technology to accurately regulate ethylene concentration in the atmosphere where fruits are preserved: a polymeric film, containing an inclusion complex of α-cyclodextrin with ethylene, was developed. The complex was prepared by molecular encapsulation which allows the entrapment of ethylene into the cavity of α-cyclodextrin. After encapsulation, ethylene can be gradually released from the inclusion complex and its release rate can be regulated by temperature and humidity. The inclusion complex was dispersed into a thin polymeric film produced by UV-curing. This method was used because is solvent-free and involves low operating temperature; both conditions are necessary to prevent rapid release of ethylene from the film. The polymeric films were characterized with respect to thermal behaviour, crystalline structure and kinetics of ethylene release, showing that can effectively control the release of ethylene within confined volume.

Statistical coronary motion models for 2D + t/3D registration of X-ray coronary angiography and CTA

DEFF Research Database (Denmark)

Baka, N.; Metz, C. T.; Schultz, C.

2013-01-01

Accurate alignment of intra-operative X-ray coronary angiography (XA) and pre-operative cardiac CT angiography (CTA) may improve procedural success rates of minimally invasive coronary interventions for patients with chronic total occlusions. It was previously shown that incorporating patient...... specific coronary motion extracted from 4D CTA increases the robustness of the alignment. However, pre-operative CTA is often acquired with gating at end-diastole, in which case patient specific motion is not available. For such cases, we investigate the possibility of using population based coronary...

Biomimetic PEGylation of carbon nanotubes through surface-initiated RAFT polymerization.

Science.gov (United States)

Shi, Yingge; Zeng, Guanjian; Xu, Dazhuang; Liu, Meiying; Wang, Ke; Li, Zhen; Fu, Lihua; Zhang, Qingsong; Zhang, Xiaoyong; Wei, Yen

2017-11-01

Carbon nanotubes (CNTs) are a type of one-dimensional carbon nanomaterials that possess excellent physicochemical properties and have been potentially utilized for a variety of applications. Surface modification of CNTs with polymers is a general route to expand and improve the performance of CNTs and has attracted great research interest over the past few decades. Although many methods have been developed previously, most of these methods still showed some disadvantages, such as low efficiency, complex experimental procedure and harsh reaction conditions etc. In this work, we reported a practical and novel way to fabricate CNTs based polymer composites via the combination of mussel inspired chemistry and reversible addition fragmentation chain transfer (RAFT) polymerization. First, the amino group was introduced onto the surface of CNTs via self-polymerization of dopamine. Then, chain transfer agent can be immobilized on the amino groups functionalized CNTs to obtain CNT-PDA-CTA, which can be utilized for surface-initiated RAFT polymerization. A water soluble and biocompatible monomer poly(ethylene glycol) monomethyl ether methacrylate (PEGMA) was adopted to fabricate pPEGMA functionalized CNTs through RAFT polymerization. The successful preparation of CNTs based polymer composites (CNT-pPEGMA) was confirmed by transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis and X-ray photoelectron spectroscopy in details. The CNT-pPEGMA showed good dispersibility and desirable biocompatibility, making them highly potential for biomedical applications. More importantly, a large number of CNTs based polymer composites could also be fabricated through the same strategy when different monomers were used due to the good monomer adaptability of RAFT polymerization. Therefore, this strategy should be a general method for preparation of various multifunctional CNTs based polymer composites. Copyright © 2017 Elsevier B.V. All rights

ITER CTA newsletter. No. 13, October 2002

International Nuclear Information System (INIS)

2002-11-01

This ITER CTA newsletter issue comprises concise information about an ITER related meeting concerning the joint implementation of ITER - the fifth ITER Negotiations Meeting - which was held in Toronto, Canada, 19-20 September, 2002, and information about assessment of the possible ITER site in Clarington, Ontario, Canada, which was the subject of the first official stage of the Joint Assessment of Specific Sites (JASS) for the ITER Project. This assessment was completed just before the Fifth ITER Negotiations Meeting

Facile Synthesis of Worm-like Micelles by Visible Light Mediated Dispersion Polymerization Using Photoredox Catalyst.

Science.gov (United States)

Yeow, Jonathan; Xu, Jiangtao; Boyer, Cyrille

2016-06-08

Presented herein is a protocol for the facile synthesis of worm-like micelles by visible light mediated dispersion polymerization. This approach begins with the synthesis of a hydrophilic poly(oligo(ethylene glycol) methyl ether methacrylate) (POEGMA) homopolymer using reversible addition-fragmentation chain-transfer (RAFT) polymerization. Under mild visible light irradiation (λ = 460 nm, 0.7 mW/cm(2)), this macro-chain transfer agent (macro-CTA) in the presence of a ruthenium based photoredox catalyst, Ru(bpy)3Cl2 can be chain extended with a second monomer to form a well-defined block copolymer in a process known as Photoinduced Electron Transfer RAFT (PET-RAFT). When PET-RAFT is used to chain extend POEGMA with benzyl methacrylate (BzMA) in ethanol (EtOH), polymeric nanoparticles with different morphologies are formed in situ according to a polymerization-induced self-assembly (PISA) mechanism. Self-assembly into nanoparticles presenting POEGMA chains at the corona and poly(benzyl methacrylate) (PBzMA) chains in the core occurs in situ due to the growing insolubility of the PBzMA block in ethanol. Interestingly, the formation of highly pure worm-like micelles can be readily monitored by observing the onset of a highly viscous gel in situ due to nanoparticle entanglements occurring during the polymerization. This process thereby allows for a more reproducible synthesis of worm-like micelles simply by monitoring the solution viscosity during the course of the polymerization. In addition, the light stimulus can be intermittently applied in an ON/OFF manner demonstrating temporal control over the nanoparticle morphology.

Four-dimensional CT angiography (4D-CTA) in the evaluation of juvenile nasopharyngeal angiofibromas: comparison with digital subtraction angiography (DSA) and surgical findings.

Science.gov (United States)

Xiao, Zebin; Zheng, Yingyan; Li, Jian; Chen, Dehua; Liu, Fang; Cao, Dairong

2017-12-01

To explore the value of four-dimensional CT angiography (4D-CTA) in the preoperative evaluation of juvenile nasopharyngeal angiofibromas (JNAs) using 320-row volume CT. 4D-CTA and DSA data of 18 patients with histopathologically proven JNAs were retrospectively reviewed. The location, extent, feeding vessels and stage of JNAs were assessed by two radiologists independently and blindly. The agreements between both reviewers and between 4D-CTA and surgical findings for assessing the above indicators were analysed, respectively. The radiation dose and the number of feeding arteries between 4D-CTA and digital subtraction angiography (DSA) were also compared. 4D-CTA showed high diagnostic consistency with surgical pathology for JNAs with consistent rates of 96.2 and 100% in both reviewers, respectively. The effective dose of 4D-CTA was significantly less than that of DSA (p 0.05). 4D-CTA can provide a reliable preoperative diagnosis and assessment of JNAs, which is useful for determining the surgical strategy and management of this condition.

Meeting of the ITER CTA project board

International Nuclear Information System (INIS)

Vlasenkov, V.

2002-01-01

This is information about meeting of the ITER CTA project board, which took place in Moscow, Russian Federation on 22 April 2002 on the occasion of the Third Negotiators Meeting (N3). Thirteen participants, representing PB members and experts from Canada (CA), the European Union (EU), Japan(JA), the Russian federation (RF) and the International Team (IT) attended the meeting chaired by Acad. E. Velikhov. The Project Board took note of the comments made concerning the status of the Participants Teams(PTs)

Design concepts for the Cherenkov Telescope Array CTA: an advanced facility for ground-based high-energy gamma-ray astronomy

International Nuclear Information System (INIS)

Allekotte, I.; Arnaldi, H.; Asorey, H.; Gomez Berisso, M.; Sofo Haro, M.; Cillis, A.; Rovero, A.C.; Supanitsky, A.D.; Actis, M.; Antico, F.; Bottani, A.; Ochoa, I.; Ringegni, P.; Vallejo, G.; De La Vega, G.; Etchegoyen, A.; Videla, M.; Gonzalez, F.; Pallota, J.; Quel, E.; Ristori, P.; Romero, G.E.; Suarez, A.; Papyan, G.; Pogosyan, L.; Sahakian, V.; Bissaldi, E.; Egberts, K.; Reimer, A.; Reimer, O.; Shellard, R.C.; Santos, E.M.; De Gouveia Dal Pino, E.M.; Kowal, G.; De Souza, V.; Todero Peixoto, C.J.; Maneva, G.; Temnikov, P.; Vankov, H.; Golev, V.; Ovcharov, E.; Bonev, T.; Dimitrov, D.; Hrupec, D.; Nedbal, D.; Rob, L.; Sillanpaa, A.; Takalo, L.; Beckmann, V.; Benallou, M.; Boutonnet, C.; Corlier, M.; Courty, B.; Djannati-Atai, A.; Dufour, C.; Gabici, S.; Guglielmi, L.; Olivetto, C.; Pita, S.; Punch, M.; Selmane, S.; Terrier, R.; Yoffo, B.; Brun, P.; Carton, P.H.; Cazaux, S.; Corpace, O.; Delagnes, E.; Disset, G.; Durand, D.; Glicenstein, J.F.; Guilloux, F.; Kosack, K.; Medina, C.; Micolon, P.; Mirabel, F.; Moulin, E.; Peyaud, B.; Reymond, J.M.; Veyssiere, C.

2011-01-01

Ground-based gamma-ray astronomy has had a major breakthrough with the impressive results obtained using systems of imaging atmospheric Cherenkov telescopes. Ground-based gamma-ray astronomy has a huge potential in astrophysics, particle physics and cosmology. CTA is an international initiative to build the next generation instrument, with a factor of 5-10 improvement in sensitivity in the 100 GeV-10 TeV range and the extension to energies well below 100 GeV and above 100 TeV. CTA will consist of two arrays (one in the north, one in the south) for full sky coverage and will be operated as open observatory. The design of CTA is based on currently available technology. This document reports on the status and presents the major design concepts of CTA. (authors)

Study on scan timing using a test injection method in head CTA

International Nuclear Information System (INIS)

Sekito, Yuichi; Sanada, Hidenori

2005-01-01

In head computed tomographic angiography (CTA), circulation from arterial phase to venous phase is more rapid than that in other regions. Therefore, it is necessary to determine correct scan timing to obtain ideal CTA images. A test injection method makes it possible to set correct scan timing from the time density curve (TDC) for each subject. The method, however, has a weak point that is a time lag in an arrival time at peak point of contrast medium on TDC between the test injection and the primary examination because of the difference in total volume of contrast medium used. The purpose of this study calculated the delay time on the TDC in both scans. We used the test injection method and the bolus tracking method in the primary examination. The average errors in start time (Δt1) and slope change time (Δt2) of the contrast medium on the TDC between test injection and primary examination were 0.15 sec and 3.05 sec, respectively. The results indicated that it was important to grasp the delay time in start time and peak arrival time of the contrast medium between test injection and primary examination to obtain ideal images in head CTA. (author)

Microsurgical management of cerebral aneurysms based in CT angiography with three-dimensional reconstruction (3D-CTA) and without preoperative cerebral angiography

International Nuclear Information System (INIS)

Gonzalez-Darder, J.M.; Pesudo-Martinez, J.V.; Feliu-Tatay, R.A.

2001-01-01

Objective. To study the possibilities of the microsurgical management of ruptured intracranial aneurysms with the sole preoperative information provided by computed tomography angiography with three-dimensional reconstruction (3D-CTA). Methods. Patients were studied with 3D-CTA after diagnosis of subarachnoid hemorrhage. If the study had an adequate quality and revealed an aneurysm congruent with the clinical findings or neurological examination and/or with the location of the bleeding on computed tomography (CT) scan an early microsurgical clipping of the lesion was done. When the quality of the 3D-CTA study was not adequate or the quality being adequate displayed no lesions or the findings were not accurate enough to warrant direct microsurgical treatment, the patient was studied with cerebral digital substraction (DS) angiography. A total of 44 consecutive patients harboring a total of 47 intracranial aneurysms diagnosed by 3D-CTA and without preoperative DS angiography were submitted to microsurgical clipping and included in the study. Results. The overall mortality was 15.9 % and the favorable results evaluated 6 months after discharge by means of the Glasgow outcome scale reached 70.4 %. All lesions were successfully clipped. Surgery was done a mean of 4.1 days after the admission bleeding. A total of four microlesions undiagnosed by 3D-CTA were found at surgery and clipped. Postoperative DS angiography and necropsy findings were also used as control of the 3D-CTA findings but no additional information was provided excepting the finding in DS angiography of an asymptomatic intracavemous aneurysm. Therefore the sensitivity of the 3D-CTA for diagnosis of symtomatic aneurysms was 100 % and the overall sensitivity 90.4 %. Conclusions. We have reached similar results in patients operated on with or without preoperative angiography. 3D-CTA provides very valuable anatomical information, which has an additional value in the microsurgical treatment of aneurysms of the

Framework for detection and localization of coronary non-calcified plaques in cardiac CTA using mean radial profiles.

Science.gov (United States)

Jawaid, Muhammad Moazzam; Riaz, Atif; Rajani, Ronak; Reyes-Aldasoro, Constantino Carlos; Slabaugh, Greg

2017-10-01

The high mortality rate associated with coronary heart disease (CHD) has driven intensive research in cardiac imaging and image analysis. The advent of computed tomography angiography (CTA) has turned non-invasive diagnosis of cardiovascular anomalies into reality as calcified coronary plaques can be easily identified due to their high intensity values. However, the detection of non-calcified plaques in CTA is still a challenging problem because of lower intensity values, which are often similar to the nearby blood and muscle tissues. In this work, we propose the use of mean radial profiles for the detection of non-calcified plaques in CTA imagery. Accordingly, we computed radial profiles by averaging the image intensity in concentric rings around the vessel centreline in a first stage. In the subsequent stage, an SVM classifier is applied to identify the abnormal coronary segments. For occluded segments, we further propose a derivative-based method to localize the position and length of the plaque inside the segment. A total of 32 CTA volumes were analysed and a detection accuracy of 88.4% with respect to the manual expert was achieved. The plaque localization accuracy was computed using the Dice similarity coefficient and a mean of 83.2% was achieved. The consistent performance for multi-vendor, multi-institution data demonstrates the reproducibility of our method across different CTA datasets with a good agreement with manual expert annotations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Comparison of biofouling mechanisms between cellulose triacetate (CTA) and thin-film composite (TFC) polyamide forward osmosis membranes in osmotic membrane bioreactors.

Science.gov (United States)

Wang, Xinhua; Zhao, Yanxiao; Yuan, Bo; Wang, Zhiwei; Li, Xiufen; Ren, Yueping

2016-02-01

There are two types of popular forward osmosis (FO) membrane materials applied for researches on FO process, cellulose triacetate (CTA) and thin film composite (TFC) polyamide. However, performance and fouling mechanisms of commercial TFC FO membrane in osmotic membrane bioreactors (OMBRs) are still unknown. In current study, its biofouling behaviors in OMBRs were investigated and further compared to the CTA FO membrane. The results indicated that β-D-glucopyranose polysaccharides and microorganisms accounted for approximately 77% of total biovolume on the CTA FO membrane while β-D-glucopyranose polysaccharides (biovolume ratio of 81.1%) were the only dominant biofoulants on the TFC FO membrane. The analyses on the biofouling structure implied that a tighter biofouling layer with a larger biovolume was formed on the CTA FO membrane. The differences in biofouling behaviors including biofoulants composition and biofouling structure between CTA and TFC FO membranes were attributed to different membrane surface properties. Copyright © 2015 Elsevier Ltd. All rights reserved.

ITER CTA newsletter. No. 16, January 2003

International Nuclear Information System (INIS)

2003-04-01

This ITER CTA newsletter contains information about some ITER related activities including ITER transitional arrangements (ITA) which will start on 1 January 2003, the USA rejoining ITER and People's Republic of China joining ITER, the visit of Mr. J. Koizumi, Prime Minister of Japan, to Kurchatov Institute, Moscow, Russian Federation on 11 January 2003, and the most recent meeting of the Scrape-Off Layer (SOL) and Divertor Physics Group of the International Tokamak Physics Activity (ITPA), which was held in Lausanne, Switzerland, on October 21-23, 2002 at the CRPP/EFL laboratory

CTA Contribution by Evaluation of Treatment AAA

International Nuclear Information System (INIS)

Mikulas, J.; Majercik, M.; Klepanec, A.; Balazs, T.; Bazik, R.; Vulev, I.

2010-01-01

Over the past decade, the EVAR (Endovascular aortic aneurysm repair) became an accepted treatment of abdominal aortic aneurysms (AAA) as compared with the radical open surgical treatment. Due to the latest generation of stents, 60% of infra renal AAA can be treated by the endovascular method or even percutaneously, without any surgical procedure, and only under the local anesthesia. We retrospectively evaluated the findings of patients following elective EVAR who underwent CTA examination immediately after the procedure and three months after the procedure, for the period from June 2009 to February 2010 (9 months).

The tempered polymerization of human neuroserpin.

Directory of Open Access Journals (Sweden)

Rosina Noto

Full Text Available Neuroserpin, a member of the serpin protein superfamily, is an inhibitor of proteolytic activity that is involved in pathologies such as ischemia, Alzheimer's disease, and Familial Encephalopathy with Neuroserpin Inclusion Bodies (FENIB. The latter belongs to a class of conformational diseases, known as serpinopathies, which are related to the aberrant polymerization of serpin mutants. Neuroserpin is known to polymerize, even in its wild type form, under thermal stress. Here, we study the mechanism of neuroserpin polymerization over a wide range of temperatures by different techniques. Our experiments show how the onset of polymerization is dependent on the formation of an intermediate monomeric conformer, which then associates with a native monomer to yield a dimeric species. After the formation of small polymers, the aggregation proceeds via monomer addition as well as polymer-polymer association. No further secondary mechanism takes place up to very high temperatures, thus resulting in the formation of neuroserpin linear polymeric chains. Most interesting, the overall aggregation is tuned by the co-occurrence of monomer inactivation (i.e. the formation of latent neuroserpin and by a mechanism of fragmentation. The polymerization kinetics exhibit a unique modulation of the average mass and size of polymers, which might suggest synchronization among the different processes involved. Thus, fragmentation would control and temper the aggregation process, instead of enhancing it, as typically observed (e.g. for amyloid fibrillation.

Helical CT for emergency patients with cerebrovascular diseases. Diagnosis of cerebral aneurysms with subarachnoid hemorrhage (SAH) by three-dimensional CT angiography (3D-CTA)

International Nuclear Information System (INIS)

Matsumoto, Masato; Satoh, Naoki; Kobayashi, Touru; Kodama, Namio; Nakano, Masayuki; Watanabe, Youichi; Fujii, Masayuki

1996-01-01

Recently, the usefulness of three-dimensional CT angiography (3D-CTA) using helical CT has been reported. Although 3D-CTA has been applied for neurosurgical diseases, especially for surgical planning, it has not done for emergency patients because of the long time required for image reconstruction and location of a helical CT scanner. We studied emergency patients with SAH, and compared the 3D-CTA with angiography and surgical findings, using TOSHIBA X vigor. Twenty-two patients with SAH were evaluated. The helical CT was performed for 55 seconds with a bolus injection of 90 ml non-ionic, iodinated contrast medium at a rate of 3 ml/sec with a delay of 20 sec. Angiography was carried out immediately after the helical CT. Eighteen of 22 cases were operated on urgently. We were able to create the 3D-CTA in about 7 minutes, and diagnose aneurysms by the 3D-CTA before angiography. The 3D-CTA was able to demonstrate 30 of 31 aneurysms including 9 unruptured aneurysms. An unruptured internal carotid-posterior communicating artery aneurysm 1.3 mm in diameter and associated with a ruptured aneurysm was not detected by either the 3D-CTA or angiography. On the other hand, an unruptured Acom aneurysm 0.8 mm in diameter and associated with a ruptured aneurysm could be detected by the: 3D-CTA, but not by angiography. The 3D-CTA gave us useful information concerning the anatomical relationship of the aneurysm, its neck and parent artery, and the surrounding branches. There were no complications or side effects associated with the helical CT scan. Although the 3D-CTA requires further development of visualization of small arteries less than 1 mm in diameter, such as perforating arteries, subtraction technique of bony structure, and a method for checking cervical arteries, it is useful for diagnosis of emergency patients with SAH and urgent operations. We believe that an operation might be performed by only the 3D-CTA without the angiography in the near future. (author)

Helical CT for emergency patients with cerebrovascular diseases. Diagnosis of cerebral aneurysms with subarachnoid hemorrhage (SAH) by three-dimensional CT angiography (3D-CTA)

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, Masato; Satoh, Naoki; Kobayashi, Touru; Kodama, Namio; Nakano, Masayuki; Watanabe, Youichi; Fujii, Masayuki [Fukushima Medical School (Japan)

1996-05-01

Recently, the usefulness of three-dimensional CT angiography (3D-CTA) using helical CT has been reported. Although 3D-CTA has been applied for neurosurgical diseases, especially for surgical planning, it has not done for emergency patients because of the long time required for image reconstruction and location of a helical CT scanner. We studied emergency patients with SAH, and compared the 3D-CTA with angiography and surgical findings, using TOSHIBA X vigor. Twenty-two patients with SAH were evaluated. The helical CT was performed for 55 seconds with a bolus injection of 90 ml non-ionic, iodinated contrast medium at a rate of 3 ml/sec with a delay of 20 sec. Angiography was carried out immediately after the helical CT. Eighteen of 22 cases were operated on urgently. We were able to create the 3D-CTA in about 7 minutes, and diagnose aneurysms by the 3D-CTA before angiography. The 3D-CTA was able to demonstrate 30 of 31 aneurysms including 9 unruptured aneurysms. An unruptured internal carotid-posterior communicating artery aneurysm 1.3 mm in diameter and associated with a ruptured aneurysm was not detected by either the 3D-CTA or angiography. On the other hand, an unruptured Acom aneurysm 0.8 mm in diameter and associated with a ruptured aneurysm could be detected by the: 3D-CTA, but not by angiography. The 3D-CTA gave us useful information concerning the anatomical relationship of the aneurysm, its neck and parent artery, and the surrounding branches. There were no complications or side effects associated with the helical CT scan. Although the 3D-CTA requires further development of visualization of small arteries less than 1 mm in diameter, such as perforating arteries, subtraction technique of bony structure, and a method for checking cervical arteries, it is useful for diagnosis of emergency patients with SAH and urgent operations. We believe that an operation might be performed by only the 3D-CTA without the angiography in the near future. (author)

The Constitution and Operation of the Constant Temperature Anemometer(CTA:IFA 300)

Energy Technology Data Exchange (ETDEWEB)

Nam, H. Y.; Kim, J. M.; Choi, B. H.; Choi, J. H.; Jeong, J. Y.; Kim, B. H.; Kim, T. J.; Cha, J. E.; Kim, H. R

2005-09-15

This study shows the constitution and application method on constant temperature anemometer(CTA-Model : IFA 300 by TSI Co.). Especially, the software instruction(Thermal Pro Ver. 4.55) was re-adjusted for users.

CTA1-DD adjuvant promotes strong immunity against human immunodeficiency virus type 1 envelope glycoproteins following mucosal immunization.

Science.gov (United States)

Sundling, Christopher; Schön, Karin; Mörner, Andreas; Forsell, Mattias N E; Wyatt, Richard T; Thorstensson, Rigmor; Karlsson Hedestam, Gunilla B; Lycke, Nils Y

2008-12-01

Strategies to induce potent and broad antibody responses against the human immunodeficiency virus type 1 (HIV-1) envelope glycoproteins (Env) at both systemic and mucosal sites represent a central goal for HIV-1 vaccine development. Here, we show that the non-toxic CTA1-DD adjuvant promoted mucosal and systemic humoral and cell-mediated immune responses following intranasal (i.n.) immunizations with trimeric or monomeric forms of HIV-1 Env in mice and in non-human primates. Env-specific IgG subclasses in the serum of immunized mice reflected a balanced Th1/Th2 type of response. Strikingly, i.n. immunizations with Env and the CTA1-DD adjuvant induced substantial levels of mucosal anti-Env IgA in bronchial alveolar lavage and also detectable levels in vaginal secretions. By contrast, parenteral immunizations of Env formulated in Ribi did not stimulate mucosal IgA responses, while the two adjuvants induced a similar distribution of Env-specific IgG-subclasses in serum. A single parenteral boost with Env in Ribi adjuvant into mice previously primed i.n. with Env and CTA1-DD, augmented the serum anti-Env IgG levels to similar magnitudes as those observed after three intraperitoneal immunizations with Env in Ribi. The augmenting potency of CTA1-DD was similar to that of LTK63 or CpG oligodeoxynucleotides (ODN). However, in contrast to CpG ODN, the effect of CTA1-DD and LTK63 appeared to be independent of MyD88 and toll-like receptor signalling. This is the first demonstration that CTA1-DD augments specific immune responses also in non-human primates, suggesting that this adjuvant could be explored further as a clinically safe mucosal vaccine adjuvant for humoral and cell-mediated immunity against HIV-1 Env.

Optimization of the Reconstruction Interval in Neurovascular 4D-CTA Imaging

Science.gov (United States)

Hoogenboom, T.C.H.; van Beurden, R.M.J.; van Teylingen, B.; Schenk, B.; Willems, P.W.A.

2012-01-01

Summary Time resolved whole brain CT angiography (4D-CTA) is a novel imaging technology providing information regarding blood flow. One of the factors that influence the diagnostic value of this examination is the temporal resolution, which is affected by the gantry rotation speed during acquisition and the reconstruction interval during post-processing. Post-processing determines the time spacing between two reconstructed volumes and, unlike rotation speed, does not affect radiation burden. The data sets of six patients who underwent a cranial 4D-CTA were used for this study. Raw data was acquired using a 320-slice scanner with a rotation speed of 2 Hz. The arterial to venous passage of an intravenous contrast bolus was captured during a 15 s continuous scan. The raw data was reconstructed using four different reconstruction-intervals: 0.2, 0.3, 0.5 and 1.0 s. The results were rated by two observers using a standardized score sheet. The appearance of each lesion was rated correctly in all readings. Scoring for quality of temporal resolution revealed a stepwise improvement from the 1.0 s interval to the 0.3 s interval, while no discernable improvement was noted between the 0.3 s and 0.2 s interval. An increase in temporal resolution may improve the diagnostic quality of cranial 4D-CTA. Using a rotation speed of 0.5 s, the optimal reconstruction interval appears to be 0.3 s, beyond which, changes can no longer be discerned. PMID:23217631

Dual energy CTA of the supraaortic arteries: Technical improvements with a novel dual source CT system

International Nuclear Information System (INIS)

Lell, Michael M.; Hinkmann, Fabian; Nkenke, Emeka; Schmidt, Bernhard; Seidensticker, Peter; Kalender, Willi A.; Uder, Michael; Achenbach, Stephan

2010-01-01

Objectives: Computed tomography angiography (CTA) is a well-accepted imaging modality to evaluate the supraaortic vessels. Initial reports have suggested that dual energy CTA (DE-CTA) can enhance diagnosis by creating bone-free data sets, which can be visualized in 3D, but a number of limitations of this technique have also been addressed. We sought to describe the performance of DE-CTA of the supraaortic vessels with a novel dual source CT system with special emphasis on image quality and post-processing related artifacts. Materials and methods: Thirty-three patients underwent carotid CT angiography on a second generation dual source CT system. Simultaneous acquisitions of 100 and 140 kV data sets in arterial phase were performed. Two examiners evaluated overall bone suppression with a 3-point scale (1 = poor; 3 = excellent) and image quality regarding integrity of the vessel lumen of different vessel segments (n = 26) with a 5-point scale (1 = poor; 5 = excellent), CTA source data served as the reference. Results: Excellent bone suppression could be achieved in the head and neck. Only minor bone remnants occurred, mean score for bone removal was 2.9. Mean score for vessel integrity was 4.3. Eight hundred fifty-seven vessel segments could be evaluated. Six hundred thirty-five segments (74%) showed no lumen alteration, 65 segments (7.6%) lumen alterations 10% resulting in a total luminal reduction 50%, and 113 segments (13.2%) showed a gap in the vessel course (100% total lumen reduction). Artificial gaps of the vessel lumen occurred in 28 vessel segments due to artifacts caused by dental hardware and in all but one (65) ophthalmic arteries. Conclusions: Excellent bone suppression could be achieved, DE imaging with 100 and 140 kV lead to improved image quality and vessel integrity in the shoulder region than previously reported. The ophthalmic artery still cannot be adequately visualized.

Comparison of X-ray radiation exposure during digital subtraction angiography (DSA) and multislice CT angiography (CTA)

International Nuclear Information System (INIS)

Bai, Mei; Liu, Bin; Zheng, Junzheng

2008-01-01

Full text: Purpose: To compare radiation risk during digital subtraction angiography (DSA) and CT angiography (CTA). Materials and methods: Eighty patients randomly divided into two groups of 40 patients each, were evaluated for coronary atherosclerotic heart disease with 64-slice spiral CT angiography and DSA respectively. For CTA group we divided patients into two subgroups: regular mode and ECG modulation mode. Matix of thermoluminescent dosimeters (TLDs) were placed on patients' skin surface during each examination to access peak skin dose (PSD). A male ART phantom was equipped with TLDs in six different positions to assess achievable organ dose. Effective dose was calculated by commercially available computer programs. Results: For DSA, PSD was 64mGy. Phantom organ dose for lung, heart, stomach, liver, kidney and brain were 11.07mGy, 5.87mGy, 1.42mGy, 2.11mGy, 6.76mGy and 0.001mGy respectively, and effective dose was 4mSv. For regular mode CTA, PSD was 74.5mGy, and CTD vol was 37.9mGy. Phantom organ dose for lung, heart, stomach, liver, kidney and brain were 58mGy, 64.2mGy, 6.6mGy, 9.9mGy, 2.7mGy, 0.072mGy respectively, and effective dose was 16mSv. For ECG modulation mode, PSD was 50.9mGy, and CTD vol was 26.3mGy. Conclusion: According to measured PSD value, deterministic radiation risk for regular mode CTA was little higher than DSA. However for stochastic radiation risk which can be indicated by organ dose and effective dose, regular mode CTA was much higher than DSA. Comparing with regular mode, ECG modulation mode can effectively reduce both stochastic and deterministic radiation risk. (author)

Meeting of the ITER CTA Project Board

International Nuclear Information System (INIS)

Vlasenkov, V.

2002-01-01

The meeting of the ITER co-ordinated technical activities project board took place in Tokyo, Japan, on 21 January 2002, coinciding with the second Negotiators meeting (N2). Twelve participants, project board members and experts from Canada, European Union, the Russian Federation and the international team attended the meeting. The project board agreed to provide an R and D plan by June 2002, to be linked with the procurement allocation, for the period following the CTA. The ITER International Team Leader developed a proposal on establishing the working groups for drafting technical specifications for the most urgent procurement items

Clinical application of lower extremity CTA and lower extremity perfusion CT as a method of diagnostic for lower extremity atherosclerotic obliterans

Energy Technology Data Exchange (ETDEWEB)

Moon, Il Bong; Dong, Kyung Rae [Dept. Radiological Technology, Gwangju Health University, Gwangju (Korea, Republic of); Goo, Eun Hoe [Dept. Radiological Science, Cheongju University, Cheongju (Korea, Republic of)

2016-11-15

The purpose of this study was to assess clinical application of lower extremity CTA and lower extremity perfusion CT as a method of diagnostic for lower extremity atherosclerotic obliterans. From January to July 2016, 30 patients (mean age, 68) were studied with lower extremity CTA and lower extremity perfusion CT. 128 channel multi-detector row CT scans were acquired with a CT scanner (SOMATOM Definition Flash, Siemens medical solution, Germany) of lower extremity perfusion CT and lower extremity CTA. Acquired images were reconstructed with 3D workstation (Leonardo, Siemens, Germany). Site of lower extremity arterial occlusive and stenosis lesions were detected superficial femoral artery 36.6%, popliteal artery 23.4%, external iliac artery 16.7%, common femoral artery 13.3%, peroneal artery 10%. The mean total DLP comparison of lower extremity perfusion CT and lower extremity CTA, 650 mGy-cm and 675 mGy-cm, respectively. Lower extremity perfusion CT and lower extremity CTA were realized that were never be two examination that were exactly the same legions. Future through the development of lower extremity perfusion CT soft ware programs suggest possible clinical applications.

TH-AB-207A-03: Skin Dose to Patients Receiving Multiple CTA and CT Exams of the Head

International Nuclear Information System (INIS)

Nawfel, RD; Young, G

2016-01-01

Purpose: To measure patient skin dose from CT angiography (CTA) and CT exams of the head, and determine if patients having multiple exams could receive cumulative doses that approach or exceed deterministic thresholds. Methods: This study was HIPAA compliant and conducted with IRB approval. Patient skin doses were measured over a 4 month period using nanoDot OSL dosimeters placed on the head of 52 patients for two CT scanners. On each scanner, 26 patients received CT exams (scanner 1: 10 females, 16 males, mean age 64.2 years; scanner 2: 18 females, 8 males, mean age 61.2 years). CT exam dose metrics, CTDIvol and dose-length product (DLP) were recorded for each exam. Additionally, skin dose was measured on an acrylic skull phantom in each scanner and on a neuro-interventional imaging system using clinical protocols. Measured dose data was used to estimate peak skin dose (PSD) for 4 patients receiving multiple exams including CTA, head CT, and cerebral angiography. Results: For scanner 1, the mean PSD for CTA exams (98.9 ± 5.3 mGy) and for routine head CT exams (39.2 ± 3.7 mGy) agreed reasonably well with the PSD measured on the phantom, 105.4 mGy and 40.0 mGy, respectively. Similarly for scanner 2, the mean PSD for CTA exams (98.8 ± 7.4 mGy) and for routine head CT exams (42.9 ± 9.4 mGy) compared well with phantom measurements, 95.2 mGy and 37.6 mGy, respectively. In addition, the mean PSD was comparable between scanners for corresponding patient exams, CTA and routine head CT respectively. PSD estimates ranged from 1.9 – 4.5 Gy among 4 patients receiving multiple exams. Conclusion: Patients having several exams including both CTA and routine head CT may receive cumulative doses approaching or exceeding the threshold for single dose deterministic effects.

TH-AB-207A-03: Skin Dose to Patients Receiving Multiple CTA and CT Exams of the Head

Energy Technology Data Exchange (ETDEWEB)

Nawfel, RD; Young, G [Brigham & Women’s Hospital, Boston, MA (United States)

2016-06-15

Purpose: To measure patient skin dose from CT angiography (CTA) and CT exams of the head, and determine if patients having multiple exams could receive cumulative doses that approach or exceed deterministic thresholds. Methods: This study was HIPAA compliant and conducted with IRB approval. Patient skin doses were measured over a 4 month period using nanoDot OSL dosimeters placed on the head of 52 patients for two CT scanners. On each scanner, 26 patients received CT exams (scanner 1: 10 females, 16 males, mean age 64.2 years; scanner 2: 18 females, 8 males, mean age 61.2 years). CT exam dose metrics, CTDIvol and dose-length product (DLP) were recorded for each exam. Additionally, skin dose was measured on an acrylic skull phantom in each scanner and on a neuro-interventional imaging system using clinical protocols. Measured dose data was used to estimate peak skin dose (PSD) for 4 patients receiving multiple exams including CTA, head CT, and cerebral angiography. Results: For scanner 1, the mean PSD for CTA exams (98.9 ± 5.3 mGy) and for routine head CT exams (39.2 ± 3.7 mGy) agreed reasonably well with the PSD measured on the phantom, 105.4 mGy and 40.0 mGy, respectively. Similarly for scanner 2, the mean PSD for CTA exams (98.8 ± 7.4 mGy) and for routine head CT exams (42.9 ± 9.4 mGy) compared well with phantom measurements, 95.2 mGy and 37.6 mGy, respectively. In addition, the mean PSD was comparable between scanners for corresponding patient exams, CTA and routine head CT respectively. PSD estimates ranged from 1.9 – 4.5 Gy among 4 patients receiving multiple exams. Conclusion: Patients having several exams including both CTA and routine head CT may receive cumulative doses approaching or exceeding the threshold for single dose deterministic effects.

Subcomponent vaccine based on CTA1-DD adjuvant with incorporated UreB class II peptides stimulates protective Helicobacter pylori immunity.

Science.gov (United States)

Nedrud, John G; Bagheri, Nayer; Schön, Karin; Xin, Wei; Bergroth, Hilda; Eliasson, Dubravka Grdic; Lycke, Nils Y

2013-01-01

A mucosal vaccine against Helicobacter pylori infection could help prevent gastric cancers and peptic ulcers. While previous attempts to develop such a vaccine have largely failed because of the requirement for safe and effective adjuvants or large amounts of well defined antigens, we have taken a unique approach to combining our strong mucosal CTA1-DD adjuvant with selected peptides from urease B (UreB). The protective efficacy of the selected peptides together with cholera toxin (CT) was first confirmed. However, CT is a strong adjuvant that unfortunately is precluded from clinical use because of its toxicity. To circumvent this problem we have developed a derivative of CT, the CTA1-DD adjuvant, that has been found safe in non-human primates and equally effective compared to CT when used intranasally. We genetically fused the selected peptides into the CTA1-DD plasmid and found after intranasal immunizations of Balb/c mice using purified CTA1-DD with 3 copies of an H. pylori urease T cell epitope (CTA1-UreB3T-DD) that significant protection was stimulated against a live challenge infection. Protection was, however, weaker than with the gold standard, bacterial lysate+CT, but considering that we only used a single epitope in nanomolar amounts the results convey optimism. Protection was associated with enhanced Th1 and Th17 immunity, but immunizations in IL-17A-deficient mice revealed that IL-17 may not be essential for protection. Taken together, we have provided evidence for the rational design of an effective mucosal subcomponent vaccine against H. pylori infection based on well selected protective epitopes from relevant antigens incorporated into the CTA1-DD adjuvant platform.

A novel non-toxic combined CTA1-DD and ISCOMS adjuvant vector for effective mucosal immunization against influenza virus.

Science.gov (United States)

Eliasson, Dubravka Grdic; Helgeby, Anja; Schön, Karin; Nygren, Caroline; El-Bakkouri, Karim; Fiers, Walter; Saelens, Xavier; Lövgren, Karin Bengtsson; Nyström, Ida; Lycke, Nils Y

2011-05-23

Here we demonstrate that by using non-toxic fractions of saponin combined with CTA1-DD we can achieve a safe and above all highly efficacious mucosal adjuvant vector. We optimized the construction, tested the requirements for function and evaluated proof-of-concept in an influenza A virus challenge model. We demonstrated that the CTA1-3M2e-DD/ISCOMS vector provided 100% protection against mortality and greatly reduced morbidity in the mouse model. The immunogenicity of the vector was superior to other vaccine formulations using the ISCOM or CTA1-DD adjuvants alone. The versatility of the vector was best exemplified by the many options to insert, incorporate or admix vaccine antigens with the vector. Furthermore, the CTA1-3M2e-DD/ISCOMS could be kept 1 year at 4°C or as a freeze-dried powder without affecting immunogenicity or adjuvanticity of the vector. Strong serum IgG and mucosal IgA responses were elicited and CD4 T cell responses were greatly enhanced after intranasal administration of the combined vector. Together these findings hold promise for the combined vector as a mucosal vaccine against influenza virus infections including pandemic influenza. The CTA1-DD/ISCOMS technology represents a breakthrough in mucosal vaccine vector design which successfully combines immunomodulation and targeting in a safe and stable particulate formation. Copyright © 2011 Elsevier Ltd. All rights reserved.

Image postprocessing of aortic CTA and MRA; Aktuelle Bildnachverarbeitung der aortalen CTA und MRA

Energy Technology Data Exchange (ETDEWEB)

Tengg-Kobligk, H. von; Weber, T.F.; Rengier, F.; Kauczor, H.U. [Deutsches Krebsforschungszentrum (DKFZ), Abteilung Radiologie E010, Heidelberg (Germany); Boeckler, D. [Ruprecht-Karls-Universitaet Heidelberg, Klinik fuer Gefaesschirurgie, vaskulaere und endovaskulaere Chrirurgie, Heidelberg (Germany); Schumacher, H. [Klinikum der Stadt Hanau, Klinik fuer Gefaesschirurgie, Hanau (Germany)

2007-11-15

Multiplanar reformation (MPR) is the most relevant tool for patient selection and precise procedural planning and also for analyzing postinterventional complications. Curved MPR is used primarily for semiautomated or completely automated calculation of the centerline of the vascular lumen and to estimate the orthogonal vessel diameter and longitudinal extent. Reproducible and accurate measurement of complex pathologies and courses of vessels extends the range of diagnostic radiology. Contemporary scanner consoles allow automated processing of maximum intensity projections (MIP) and standard MPR and their storage in PACS. To improve patient selection, procedural planning, root-cause analysis postoperatively for assessment of treatment effects and to make better communication of findings to nonradiologists possible, volume rendering techniques (VRT) are a beneficial adjunct to source images. With current algorithms semiautomated segmentation is satisfactory for vessels and bones, but not for low-contrast structures (soft tissues), which still need to be segmented manually. In general, isotropic CT source data are preferable to MR images, which are often anisotropic. In many European countries image postprocessing is still not adequately reimbursed although the doctors making referrals often specifically and emphatically demand 3D visualization and measurements in daily practice. (orig.) [German] Die multiplanare Reformatierung (MPR) der Bilddaten aortaler CTA und MRA ist die wichtigste Rekonstruktionsmethode im Hinblick auf eine differenzierte Therapieentscheidung und die praeoperative Therapieplanung sowie die Beschreibung postoperativer Komplikationen. Die gekruemmte MPR wird semiautomatisch bzw. vollstaendig automatisch als Centerline im Gefaesslumen berechnet und fuer die Bestimmung des orthogonalen Durchmessers und der Laengsausdehnung der Pathologie verwendet. Eine reproduzierbar exakte Ausmessung komplexer Pathologien und Gefaesslaengsverlaeufe erweitert das

Dual energy CTA of the supraaortic arteries: Technical improvements with a novel dual source CT system

Energy Technology Data Exchange (ETDEWEB)

Lell, Michael M., E-mail: Michael.lell@uk-erlangen.de [Department of Radiology, University Erlangen, Maximiliansplatz 1, 91054 Erlangen (Germany); Hinkmann, Fabian [Department of Radiology, University Erlangen, Maximiliansplatz 1, 91054 Erlangen (Germany); Nkenke, Emeka [Department of Maxillofacial Surgery, University Erlangen (Germany); Schmidt, Bernhard [Bayer-Schering Healthcare, Berlin (Germany); Seidensticker, Peter [Siemens Healthcare, CT-Division, Forchheim (Germany); Kalender, Willi A. [Institute of Medical Physics, University Erlangen (Germany); Uder, Michael [Department of Radiology, University Erlangen, Maximiliansplatz 1, 91054 Erlangen (Germany); Achenbach, Stephan [Department of Cardiology, University Erlangen (Germany)

2010-11-15

Objectives: Computed tomography angiography (CTA) is a well-accepted imaging modality to evaluate the supraaortic vessels. Initial reports have suggested that dual energy CTA (DE-CTA) can enhance diagnosis by creating bone-free data sets, which can be visualized in 3D, but a number of limitations of this technique have also been addressed. We sought to describe the performance of DE-CTA of the supraaortic vessels with a novel dual source CT system with special emphasis on image quality and post-processing related artifacts. Materials and methods: Thirty-three patients underwent carotid CT angiography on a second generation dual source CT system. Simultaneous acquisitions of 100 and 140 kV data sets in arterial phase were performed. Two examiners evaluated overall bone suppression with a 3-point scale (1 = poor; 3 = excellent) and image quality regarding integrity of the vessel lumen of different vessel segments (n = 26) with a 5-point scale (1 = poor; 5 = excellent), CTA source data served as the reference. Results: Excellent bone suppression could be achieved in the head and neck. Only minor bone remnants occurred, mean score for bone removal was 2.9. Mean score for vessel integrity was 4.3. Eight hundred fifty-seven vessel segments could be evaluated. Six hundred thirty-five segments (74%) showed no lumen alteration, 65 segments (7.6%) lumen alterations <10%, 27 segments (3.1%) lumen alterations >10% resulting in a total luminal reduction <50%, 17 segments (2%) lumen alterations of more than 10% resulting in a total luminal reduction >50%, and 113 segments (13.2%) showed a gap in the vessel course (100% total lumen reduction). Artificial gaps of the vessel lumen occurred in 28 vessel segments due to artifacts caused by dental hardware and in all but one (65) ophthalmic arteries. Conclusions: Excellent bone suppression could be achieved, DE imaging with 100 and 140 kV lead to improved image quality and vessel integrity in the shoulder region than previously

Subcomponent vaccine based on CTA1-DD adjuvant with incorporated UreB class II peptides stimulates protective Helicobacter pylori immunity.

Directory of Open Access Journals (Sweden)

John G Nedrud

Full Text Available A mucosal vaccine against Helicobacter pylori infection could help prevent gastric cancers and peptic ulcers. While previous attempts to develop such a vaccine have largely failed because of the requirement for safe and effective adjuvants or large amounts of well defined antigens, we have taken a unique approach to combining our strong mucosal CTA1-DD adjuvant with selected peptides from urease B (UreB. The protective efficacy of the selected peptides together with cholera toxin (CT was first confirmed. However, CT is a strong adjuvant that unfortunately is precluded from clinical use because of its toxicity. To circumvent this problem we have developed a derivative of CT, the CTA1-DD adjuvant, that has been found safe in non-human primates and equally effective compared to CT when used intranasally. We genetically fused the selected peptides into the CTA1-DD plasmid and found after intranasal immunizations of Balb/c mice using purified CTA1-DD with 3 copies of an H. pylori urease T cell epitope (CTA1-UreB3T-DD that significant protection was stimulated against a live challenge infection. Protection was, however, weaker than with the gold standard, bacterial lysate+CT, but considering that we only used a single epitope in nanomolar amounts the results convey optimism. Protection was associated with enhanced Th1 and Th17 immunity, but immunizations in IL-17A-deficient mice revealed that IL-17 may not be essential for protection. Taken together, we have provided evidence for the rational design of an effective mucosal subcomponent vaccine against H. pylori infection based on well selected protective epitopes from relevant antigens incorporated into the CTA1-DD adjuvant platform.

Electrochemical Impedance Spectroscopy—A Simple Method for the Characterization of Polymer Inclusion Membranes Containing Aliquat 336

Science.gov (United States)

O'Rourke, Michelle; Duffy, Noel; De Marco, Roland; Potter, Ian

2011-01-01

Electrochemical impedance spectroscopy (EIS) has been used to estimate the non-frequency dependent (static) dielectric constants of base polymers such as poly(vinyl chloride) (PVC), cellulose triacetate (CTA) and polystyrene (PS). Polymer inclusion membranes (PIMs) containing different amounts of PVC or CTA, along with the room temperature ionic liquid Aliquat 336 and plasticizers such as trisbutoxyethyl phosphate (TBEP), dioctyl sebecate (DOS) and 2-nitrophenyloctyl ether (NPOE) have been investigated. In this study, the complex and abstract method of EIS has been applied in a simple and easy to use way, so as to make the method accessible to membrane scientists and engineers who may not possess the detailed knowledge of electrochemistry and interfacial science needed for a rigorous interpretation of EIS results. The EIS data reported herein are internally consistent with a percolation threshold in the dielectric constant at high concentrations of Aliquat 336, which illustrates the suitability of the EIS technique since membrane percolation with ion exchangers is a well-known phenomenon. PMID:24957616

The immune complex CTA1-DD/IgG adjuvant specifically targets connective tissue mast cells through FcγRIIIA and augments anti-HPV immunity after nasal immunization.

Science.gov (United States)

Fang, Y; Zhang, T; Lidell, L; Xu, X; Lycke, N; Xiang, Z

2013-11-01

We have previously reported that CTA1-DD/IgG immune complexes augment antibody responses in a mast cell-dependent manner following intranasal (IN) immunizations. However, from a safety perspective, mast cell activation could preclude clinical use. Therefore, we have extended these studies and demonstrate that CTA1-DD/IgG immune complexes administered IN did not trigger an anaphylactic reaction. Importantly, CTA1-DD/IgE immune complexes did not activate mast cells. Interestingly, only connective tissue, but not mucosal, mast cells could be activated by CTA1-DD/IgG immune complexes. This effect was mediated by FcγRIIIA, only expressed on connective tissue mast cells, and found in the nasal submucosa. FcγRIIIA-deficient mice had compromised responses to immunization adjuvanted by CTA1-DD/IgG. Proof-of-concept studies revealed that IN immunized mice with human papillomavirus (HPV) type 16 L1 virus-like particles (VLP) and CTA1-DD/IgG immune complexes demonstrated strong and sustained specific antibody titers in serum and vaginal secretions. From a mast cell perspective, CTA1-DD/IgG immune complexes appear to be safe and effective mucosal adjuvants.

Some characteristics of protons emitted in backward hemisphere in dTa and CTa interactions at Psub(0)=4.2 GeV/c

International Nuclear Information System (INIS)

Gasparyan, A.P.; Mekhtiev, R.R.

1985-01-01

In interactions of deuterium and carbon relativistic nuclei with tantalum at P 0 =4.2 GeV/c for secondary protons with 100 deg emission angle in lab. system, the temperature of proton kinetic energy spectra in three angle intervals has been determined. It does not contradict the values obtained in hadron-nuclear interactions. The slope parameters for backward emitted proton spectra over comulative variable β=/E-psub(11) msub(p) in dTa and CTa collisions and hadron-nucleus interactions are approximately equal as well. At the same time some difference of s: ope parameters on kinetic energy and cumulative variables spectra between dTa and CTa is observed. In CTa collisions the spectra are deeper. The comparison with the predictions of cascade model for CTa interactions is made. The cascade model taking into account the final state interaction of nucleons on the whole satisfactorily describes the experimental data

Improving head and neck CTA with hybrid and model-based iterative reconstruction techniques

NARCIS (Netherlands)

Niesten, J. M.; van der Schaaf, I. C.; Vos, P. C.; Willemink, MJ; Velthuis, B. K.

2015-01-01

AIM: To compare image quality of head and neck computed tomography angiography (CTA) reconstructed with filtered back projection (FBP), hybrid iterative reconstruction (HIR) and model-based iterative reconstruction (MIR) algorithms. MATERIALS AND METHODS: The raw data of 34 studies were

Low-tube-voltage selection for triple-rule-out CTA: relation to patient size

Energy Technology Data Exchange (ETDEWEB)

Takx, Richard A.P. [University Medical Center Utrecht, Department of Radiology, Utrecht (Netherlands); Krissak, Radko [Medical Faculty Mannheim - Heidelberg University, Institute of Clinical Radiology and Nuclear Medicine, University Medical Center Mannheim (Germany); Hufeland Klinikum GmbH, Department of Diagnostic and Interventional Radiology, Bad Langensalza (Germany); Fink, Christian [Medical Faculty Mannheim - Heidelberg University, Institute of Clinical Radiology and Nuclear Medicine, University Medical Center Mannheim (Germany); General Hospital Celle, Department of Radiology, Celle (Germany); Bachmann, Valentin; Henzler, Thomas; Meyer, Mathias; Schoenberg, Stefan O. [Medical Faculty Mannheim - Heidelberg University, Institute of Clinical Radiology and Nuclear Medicine, University Medical Center Mannheim (Germany); Nance, John W. [Medical University of South Carolina, Division of Cardiovascular Imaging, Department of Radiology and Radiological Science, Charleston, SC (United States); Apfaltrer, Paul [Medical Faculty Mannheim - Heidelberg University, Institute of Clinical Radiology and Nuclear Medicine, University Medical Center Mannheim (Germany); Medical University of Vienna, Department of Biomedical Imaging and Image-guided Therapy, Vienna (Austria)

2017-06-15

To investigate the relationship between image quality and patient size at 100 kilovoltage (kV) compared to 120 kV ECG-gated Triple-Rule-Out CT angiography (TRO-CTA). We retrospectively included 73 patients (age 64 ± 14 years) who underwent retrospective ECG-gated chest CTA. 40 patients were scanned with 100 kV while 33 patients with 120 kV. Body mass index (BMI), patients' chest circumference (PC) and thoracic surface area (TSA) were recorded. Quantitative image quality was assessed as vascular attenuation in the ascending aorta (AA), pulmonary trunk (PA) and left coronary artery (LCA) and the signal-to-noise ratio (SNR) in the AA. There was no significant difference in BMI (26.0 ± 4.6 vs. 28.0 ± 6.7 kg/m{sup 2}), PC (103 ± 7 vs. 104 ± 10 cm{sup 2}) and TSA (92 ± 15 vs. 91 ± 19 cm{sup 2}) between 100 kV and 120 kV group. Mean vascular attenuation was significantly higher in the 100 kV compared to the 120 kV group (AA 438 vs. 354 HU, PA 460 vs. 349 HU, LCA 370 vs. 299 HU all p < 0.001). SNR was not significantly different, even after adjusting for patient size. Radiation dose was significantly lower in the 100 kV group (10.7 ± 4.1 vs. 20.7 ± 10.7 mSv; p < 0.001). 100 kV TRO-CTA is feasible in normal-to-overweight patients while maintaining image quality and achieving substantial dose reduction. (orig.)

Reducing radiation dose without compromising image quality in preoperative perforator flap imaging with CTA using ASIR technology.

Science.gov (United States)

Niumsawatt, Vachara; Debrotwir, Andrew N; Rozen, Warren Matthew

2014-01-01

Computed tomographic angiography (CTA) has become a mainstay in preoperative perforator flap planning in the modern era of reconstructive surgery. However, the increased use of CTA does raise the concern of radiation exposure to patients. Several techniques have been developed to decrease radiation dosage without compromising image quality, with varying results. The most recent advance is in the improvement of image reconstruction using an adaptive statistical iterative reconstruction (ASIR) algorithm. We sought to evaluate the image quality of ASIR in preoperative deep inferior epigastric perforator (DIEP) flap surgery, through a direct comparison with conventional filtered back projection (FBP) images. A prospective review of 60 consecutive ASIR and 60 consecutive FBP CTA images using similar protocol (except for radiation dosage) was undertaken, analyzed by 2 independent reviewers. In both groups, we were able to accurately identify axial arteries and their perforators. Subjective analysis of image quality demonstrated no statistically significant difference between techniques. ASIR can thus be used for preoperative imaging with similar image quality to FBP, but with a 60% reduction in radiation delivery to patients.

Evaluation of a multi-atlas based method for segmentation of cardiac CTA data: a large-scale, multicenter, and multivendor study

International Nuclear Information System (INIS)

Kirisli, H. A.; Schaap, M.; Klein, S.; Papadopoulou, S. L.; Bonardi, M.; Chen, C. H.; Weustink, A. C.; Mollet, N. R.; Vonken, E. J.; Geest, R. J. van der; Walsum, T. van; Niessen, W. J.

2010-01-01

Purpose: Computed tomography angiography (CTA) is increasingly used for the diagnosis of coronary artery disease (CAD). However, CTA is not commonly used for the assessment of ventricular and atrial function, although functional information extracted from CTA data is expected to improve the diagnostic value of the examination. In clinical practice, the extraction of ventricular and atrial functional information, such as stroke volume and ejection fraction, requires accurate delineation of cardiac chambers. In this paper, we investigated the accuracy and robustness of cardiac chamber delineation using a multiatlas based segmentation method on multicenter and multivendor CTA data. Methods: A fully automatic multiatlas based method for segmenting the whole heart (i.e., the outer surface of the pericardium) and cardiac chambers from CTA data is presented and evaluated. In the segmentation approach, eight atlas images are registered to a new patient's CTA scan. The eight corresponding manually labeled images are then propagated and combined using a per voxel majority voting procedure, to obtain a cardiac segmentation. Results: The method was evaluated on a multicenter/multivendor database, consisting of (1) a set of 1380 Siemens scans from 795 patients and (2) a set of 60 multivendor scans (Siemens, Philips, and GE) from different patients, acquired in six different institutions worldwide. A leave-one-out 3D quantitative validation was carried out on the eight atlas images; we obtained a mean surface-to-surface error of 0.94±1.12 mm and an average Dice coefficient of 0.93 was achieved. A 2D quantitative evaluation was performed on the 60 multivendor data sets. Here, we observed a mean surface-to-surface error of 1.26±1.25 mm and an average Dice coefficient of 0.91 was achieved. In addition to this quantitative evaluation, a large-scale 2D and 3D qualitative evaluation was performed on 1380 and 140 images, respectively. Experts evaluated that 49% of the 1380 images

Evaluation of a polymer inclusion membrane containing a C-pivot tripodal diglycolamide for Am(III) extraction

International Nuclear Information System (INIS)

Mahanty, B.N.; Das, D.K.; Afzal, Md; Raut, D.R.; Mohapatra, P.K.; Behere, P.G.; Verboom, W.

2014-01-01

The instability of supported liquid membrane (SLM), being used for laboratory scale metal ion separation, can be avoided using Polymer inclusion membranes (PIM). We have been carrying out studies on diglycolamide based extractants including a C-pivot tripodal diglycolamide (T-DGA) for actinide ion separation from acidic feed solution. It was thought of interest to study the properties of T-DGA based PIM containing cellulose triacetate (CTA) as polymer and 2-nitrophenyl octyl ether (NPOE) as the plasticizer for Am(III) uptake and transport

Dual-energy CTA in patients with symptomatic peripheral arterial occlusive disease. Study of diagnostic accuracy and impeding factors

Energy Technology Data Exchange (ETDEWEB)

Klink, Thorsten [Wuerzburg Univ. (Germany). Inst. of Diagnostic and Interventional Radiology; Bern Univ. (Switzerland). Univ. Inst. of Diagnostic, Interventional, and Pediatric Radiology; Wilhelm, Theresa; Roth, Christine [Univ. Hospital Giessen and Marburg, Marburg (Germany). Dept. of Diagnostic and Interventional Radiology; Heverhagen, Johannes T. [Bern Univ. (Switzerland). Univ. Inst. of Diagnostic, Interventional, and Pediatric Radiology

2017-05-15

The purpose of this study was to assess the diagnostic performance of dual-energy CT angiography (DE-CTA) in patients with symptomatic peripheral artery occlusive disease (PAOD) and to identify factors that impede its diagnostic accuracy. Dual-source DE-CTA scans of the lower extremities of 94 patients were retrospectively compared to the diagnostic reference standard, digital subtraction angiography (DSA). Two independent observers assessed PAOD incidence, image quality, artifacts, and diagnostic accuracy of DE-CTA in 1014 arterial segments on axial, combined 80/140 kVp reconstructions and on 3 D maximum intensity projections (MIP) after automated bone and plaque removal. The impact of calcifications, image quality, and image artifacts on the diagnostic accuracy was evaluated using Fisher's exact test. Furthermore, interobserver agreement was analyzed. Two observers achieved sensitivities of 98.0% and 93.9%, respectively, and specificities of 75.0% and 66.7%, respectively, for detecting stenoses of >50% of the lower extremity arteries. Calcifications impeded specificity, e.g. from 81.2% to 46.2% for reader 1 (p<0.001). Specificity increased with higher image quality, e.g. from 70.0% to 76.4% for reader 1 (p<0.001). Artifacts decreased the specificity of reader 2 (p<0.001). The overall interobserver agreement ranged between moderate and substantial for stenosis detection and calcified plaques. Conclusion DE-CTA is accurate in the detection of arterial stenoses of >50% in symptomatic PAOD patients. Calcified atherosclerotic plaques, image quality, and artifacts may impede specificity.

Instrumentation for comparing night sky quality and atmospheric conditions of CTA site candidates

International Nuclear Information System (INIS)

Fruck, C.; Schweizer, T.; Häfner, D.; Lorentz, E.; Teshima, M.; Gaug, M.; Ernenwein, J.-P.; Costantini, H.; Mandát, D.; Pech, M.; Bulik, T.; Cieslar, M.; Dominik, M.; Ebr, J.; Garczarczyk, M.; Pareschi, G.; Puerto-Giménez, I.

2015-01-01

Many atmospheric and climatic criteria have to be taken into account for the selection of a suitable site for the next generation of imaging air-shower Cherenkov telescopes, the ''Cherenkov Telescope Array'' CTA. Such data are not available with sufficient precision, thus a comparison of the proposed sites and final decision based on a comprehensive characterization is impossible. Identical cross-calibrated instruments have been developed which allow for precise comparison between sites, the cross-validation of existing data, and the ground-validation of satellite data. The site characterization work package of the CTA consortium opted to construct and deploy 9 copies of an autonomous multi-purpose weather sensor, incorporating an infrared cloud sensor, a newly developed sensor for measuring the light of the night sky, and an All-Sky-Camera, the whole referred to as Autonomous Tool for Measuring Observatory Site COnditions PrEcisely (ATMOSCOPE). We present here the hardware that was combined into the ATMOSCOPE and characterize its performance

Added Value of 3D Cardiac SPECT/CTA Fusion Imaging in Patients with Reversible Perfusion Defect on Myocardial Perfusion SPECT

Energy Technology Data Exchange (ETDEWEB)

Kong, Eun Jung; Cho, Ihn Ho [Yeungnam University Hospital, Daegu (Korea, Republic of); Kang, Won Jun [Yonsei University Hospital, Seoul (Korea, Republic of); Kim, Seong Min [Chungnam National University Medical School and Hospital, Daejeon (Korea, Republic of); Won, Kyoung Sook [Keomyung University Dongsan Hospital, Daegu (Korea, Republic of); Lim, Seok Tae [Chonbuk National University Medical School and Hospital, Jeonju (Korea, Republic of); Hwang, Kyung Hoon [Gachon University Gil Hospital, Incheon (Korea, Republic of); Lee, Byeong Il; Bom, Hee Seung [Chonnam National University Medical School and Hospital, Gwangju (Korea, Republic of)

2009-12-15

Integration of the functional information of myocardial perfusion SPECT (MPS) and the morphoanatomical information of coronary CT angiography (CTA) may provide useful additional diagnostic information of the spatial relationship between perfusion defects and coronary stenosis. We studied to know the added value of three dimensional cardiac SPECT/CTA fusion imaging (fusion image) by comparing between fusion image and MPS. Forty-eight patients (M:F=26:22, Age: 63.3{+-}10.4 years) with a reversible perfusion defect on MPS (adenosine stress/rest SPECT with Tc-99m sestamibi or tetrofosmin) and CTA were included. Fusion images were molded and compared with the findings from the MPS. Invasive coronary angiography served as a reference standard for fusion image and MPS. Total 144 coronary arteries in 48 patients were analyzed; Fusion image yielded the sensitivity, specificity, negative and positive predictive value for the detection of hemodynamically significant stenosis per coronary artery 82.5%, 79.3%, 76.7% and 84.6%, respectively. Respective values for the MPS were 68.8%, 70.7%, 62.1% and 76.4%. And fusion image also could detect more multi-vessel disease. Fused three dimensional volume-rendered SPECT/CTA imaging provides intuitive convincing information about hemodynamic relevant lesion and could improved diagnostic accuracy.

Functionalization of vertically aligned carbon nanotubes with polystyrene via surface initiated reversible addition fragmentation chain transfer polymerization

Energy Technology Data Exchange (ETDEWEB)

Macdonald, Thomas; Gibson, Christopher T.; Constantopoulos, Kristina; Shapter, Joseph G. [Flinders Centre for Nanoscale Science and Technology, School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, SA, 5001 (Australia); Ellis, Amanda V., E-mail: amanda.ellis@flinders.edu.au [Flinders Centre for Nanoscale Science and Technology, School of Chemical and Physical Sciences, Flinders University, GPO Box 2100, Adelaide, SA, 5001 (Australia)

2012-01-15

Here we demonstrate the covalent attachment of vertically aligned (VA) acid treated single-walled carbon nanotubes (SWCNTs) onto a silicon substrate via dicyclohexylcarbodiimide (DCC) coupling chemistry. Subsequently, the pendant carboxyl moieties on the sidewalls of the VA-SWCNTs were derivatized to acyl chlorides, and then finally to bis(dithioester) moieties using a magnesium chloride dithiobenzoate salt. The bis(dithioester) moieties were then successfully shown to act as a chain transfer agent (CTA) in the reversible addition fragmentation chain transfer (RAFT) polymerization of styrene in a surface initiated 'grafting-from' process from the VA-SWCNT surface. Atomic force microscopy (AFM) verified vertical alignment of the SWCNTs and the maintenance thereof throughout the synthesis process. Finally, Raman scattering spectroscopy and AFM confirmed polystyrene functionalization.

Functionalization of vertically aligned carbon nanotubes with polystyrene via surface initiated reversible addition fragmentation chain transfer polymerization

International Nuclear Information System (INIS)

Macdonald, Thomas; Gibson, Christopher T.; Constantopoulos, Kristina; Shapter, Joseph G.; Ellis, Amanda V.

2012-01-01

Here we demonstrate the covalent attachment of vertically aligned (VA) acid treated single-walled carbon nanotubes (SWCNTs) onto a silicon substrate via dicyclohexylcarbodiimide (DCC) coupling chemistry. Subsequently, the pendant carboxyl moieties on the sidewalls of the VA-SWCNTs were derivatized to acyl chlorides, and then finally to bis(dithioester) moieties using a magnesium chloride dithiobenzoate salt. The bis(dithioester) moieties were then successfully shown to act as a chain transfer agent (CTA) in the reversible addition fragmentation chain transfer (RAFT) polymerization of styrene in a surface initiated “grafting-from” process from the VA-SWCNT surface. Atomic force microscopy (AFM) verified vertical alignment of the SWCNTs and the maintenance thereof throughout the synthesis process. Finally, Raman scattering spectroscopy and AFM confirmed polystyrene functionalization.

Constructive Technology Assessment (CTA) as a tool in coverage with evidence development: the case of the 70-gene prognosis signature for breast cancer diagnostics

NARCIS (Netherlands)

Retel, Valesca; Retèl, Valesca P.; Bueno-de-Mesquita, Jolien M.; Hummel, J. Marjan; van de Vijver, Marc J.; Douma, Kirsten F.L.; Karsenberg, Kim; van Dam, Frits S.A.M.; van Krimpen, Cees; Bellot, Frank E.; Roumen, Rudi M.H.; Linn, Sabine C.; van Harten, Willem H.

2009-01-01

Objectives: Constructive Technology Assessment (CTA) is a means to guide early implementation of new developments in society, and can be used as an evaluation tool for Coverage with Evidence Development (CED). We used CTA for the introduction of a new diagnostic test in the Netherlands, the 70-gene

Constructive Technology Assessment (CTA) as a tool in Coverage with Evidence Development: The case of the 70-gene prognosis signature for breast cancer diagnostics

NARCIS (Netherlands)

Retèl, Valesca P.; Bueno-de-Mesquita, Jolien M.; Hummel, Marjan J. M.; van de Vijver, Marc J.; Douma, Kirsten F. L.; Karsenberg, Kim; van Dam, Frits S. A. M.; van Krimpen, Cees; Bellot, Frank E.; Roumen, Rudi M. H.; Linn, Sabine C.; van Harten, Wim H.

2009-01-01

Objectives: Constructive Technology Assessment (CTA) is a means to guide early implementation of new developments in society, and can be used as an evaluation tool for Coverage with Evidence Development (CED). We used CTA for the introduction of a new diagnostic test in the Netherlands, the 70-gene

The diagnostic accuracy of TCD for intracranial arterial stenosis/occlusion in patients with acute ischemic stroke: the importance of time interval between detection of TCD and CTA.

Science.gov (United States)

Guan, Jingxia; Zhou, Qin; Ouyang, Huangqing; Zhang, Shaofeng; Lu, Zuneng

2013-11-01

To evaluate prospectively the diagnostic accuracy of transcranial doppler (TCD) as an additional screening tool for intracranial arterial steno-occlusive disease against computed tomography angiography (CTA) in patients with acute ischemic stroke (AIS) if both are performed in a short time interval. Between July 2011 and May 2012, 128 patients who were hospitalized within 24 hours of symptom onset and fulfilled the criteria for the clinical diagnosis of AIS were enrolled. Bedside detection of TCD was accomplished immediately after admission. High-resolution brain CTA was performed within 3 hours after the completion of TCD and the images were interpreted by a neuroradiologist blinded to TCD findings. The accuracy parameters of TCD against CTA were calculated after computation of true-positive, false-positive, true negative, and false-negative values. Among the 128 patients, there were 68 males and 60 females, aged 61.4 ± 17.5 years. The mean time interval between the detection of TCD and CTA was 89.7 (77.8) minutes. In 65% of patients, both examinations were performed with less than a half-hour interval between them. The diagnostic accuracy of TCD for different arteries showed slight distinction. Transcranial doppler demonstrated the most accurate diagnosis for middle cerebral artery (MCA), where TCD showed 35 true-positive, 0 false-negative, 1 false-positive, and 92 true-negative studies compared with CTA. Furthermore, elevated MCA velocities on TCD correlated well with the severity of intracranial stenosis detected on CTA. Vertebral artery (VA) is one of the arteries with the lowest sensitivity for TCD diagnosis (sensitivity 63.4%, specificity 96.5%, positive predictive value (PPV) 89.6%, negative predictive value (NPV) 84.8%, and accuracy 85.9%). In 20 cases (15.6%), TCD showed findings complementary to CTA (real-time embolization, collateral flow patterns, and steal phenomenon). Transcranial doppler shows high diagnostic accuracy against CTA if both are

Novel polymer inclusion membranes containing T2EHDGA as carrier extractant for actinide ion uptake from acidic feeds

Energy Technology Data Exchange (ETDEWEB)

Mahanty, Bholanath; Das, Dillip Kumar; Behere, Praveen Gajanan; Afzal, Mohammad [Bhabha Atomic Research Centre, Tarapur, Maharashtra (India). Advanced Fuel Fabrication Facility; Mohapatra, Prasanta Kumar; Raut, Dhaval Ramakant [Bhabha Atomic Research Centre, Trombay, Mumbai (India). Radiochemistry Div.

2015-06-01

Polymer inclusion membranes (PIM) containing N,N,N',N'-tetra(2-ethylhexyl) diglycolamide (T2EHDGA) were evaluated for the separation of actinide ions such as Am{sup 3+}, Pu{sup 4+}, UO{sub 2}{sup 2+} and Th{sup 4+} from acidic feeds. The PIMs were prepared using cellulose triacetate (CTA) as the polymer matrix, 2-nitrophenyloctyl ether (NPOE) as the plasticizer and T2EHDGA as the carrier extractant and the optimized membrane composition was found to be 68.4% T2EHDGA, 17.9% NPOE and 13.7% CTA which resulted in 74% Am{sup 3+} uptake at 1 M HNO{sub 3} in 2 h. The uptake studies were carried out using feed solutions containing varying concentrations of nitric acid (0.5-3.0 M) and showed the trend: Pu{sup 4+} > Am{sup 3+} > Th{sup 4+} > UO{sub 2}{sup 2+}. Quantitative stripping (> 99%) of the sorbed Am{sup 3+} was possible using a solution containing 0.01 M EDTA at pH 3.0. Reusability studies indicated deterioration of the PIM on continuous use.

Click polymerization for the synthesis of reduction-responsive polymeric prodrug

Science.gov (United States)

Zhang, Xiaojin; Wang, Hongquan; Dai, Yu

2018-05-01

Click polymerization is a powerful polymerization technique for the construction of new macromolecules with well-defined structures and multifaceted functionalities. Here, we synthesize reduction-responsive polymeric prodrug PEG- b-(PSS- g-MTX)- b-PEG containing disulfide bonds and pendant methotrexate (MTX) via two-step click polymerization followed by conjugating MTX to pendant hydroxyl. MTX content in polymeric prodrug is 13.5%. Polymeric prodrug is able to form polymeric micelles by self-assembly in aqueous solution. Polymeric micelles are spherical nanoparticles with tens of nanometers in size. Of note, polymeric micelles are reduction-responsive due to disulfide bonds in the backbone of PEG- b-(PSS- g-MTX)- b-PEG and could release pendant drugs in the presence of the reducing agents such as dl-dithiothreitol (DTT).

COLIBRI: partial camera readout and sliding trigger for the Cherenkov Telescope Array CTA

International Nuclear Information System (INIS)

Naumann, C L; Tejedor, L A; Martínez, G

2013-01-01

Plans for the future Cherenkov telescope array CTA include replacing the monolithic camera designs used in H.E.S.S. and MAGIC-I by one that is built up from a number of identical segments. These so-called clusters will be relatively autonomous, each containing its own triggering and readout hardware. While this choice was made for reasons of flexibility and ease of manufacture and maintenance, such a concept with semi-independent sub-units lends itself quite naturally to the possibility of new, and more flexible, readout modes. In all previously-used concepts, triggering and readout of the camera is centralised, with a single camera trigger per event that starts the readout of all pixels in the camera at the same time and within the same integration time window. The limitations of such a trigger system can reduce the performance of a large array such as CTA, due to the huge amount of useless data created by night-sky background if trigger thresholds are set low enough to achieve the desired 20 GeV energy threshold, and to image losses at high energies due to the rigid readout window. In this study, an alternative concept (''COLIBRI'' = Concept for an Optimised Local Image Building and Readout Infrastructure) is presented, where only those parts of the camera which are likely to actually contain image data (usually a small percentage of the total pixels) are read out. This leads to a significant reduction of the expected data rate and the dead-times incurred in the camera. Furthermore, the quasi-independence of the individual clusters can be used to read different parts of the camera at slightly different times, thus allowing the readout to follow the slow development of the shower image across the camera field of view. This concept of flexible, partial camera readout is presented in the following, together with a description of Monte-Carlo studies performed to evaluate its performance as well as a hardware implementation proposed for CTA.

Pulsed-laser polymerization in compartmentalized liquids. 1. Polymerization in vesicles

NARCIS (Netherlands)

Jung, M.; Casteren, van I.A.; Monteiro, M.J.; Herk, van A.M.; German, A.L.

2000-01-01

Polymerization in vesicles is a novel type of polymerization in heterogeneous media, leading to parachute-like vesicle-polymer hybrid morphologies. To explore the kinetics of vesicle polymerizations and to learn more about the actual locus of polymerization we applied the pulsed-laser polymerization

The control system of the 12-m medium-size telescope prototype: a test-ground for the CTA array control

Science.gov (United States)

Oya, I.; Anguner, E. A.; Behera, B.; Birsin, E.; Fuessling, M.; Lindemann, R.; Melkumyan, D.; Schlenstedt, S.; Schmidt, T.; Schwanke, U.; Sternberger, R.; Wegner, P.; Wiesand, S.

2014-07-01

The Cherenkov Telescope Array (CTA) will be the next generation ground-based very-high energy -ray observatory. CTA will consist of two arrays: one in the Northern hemisphere composed of about 20 telescopes, and the other one in the Southern hemisphere composed of about 100 telescopes, both arrays containing telescopes of different sizes and types and in addition numerous auxiliary devices. In order to provide a test-ground for the CTA array control, the steering software of the 12-m medium size telescope (MST) prototype deployed in Berlin has been implemented using the tools and design concepts under consideration to be used for the control of the CTA array. The prototype control system is implemented based on the Atacama Large Millimeter/submillimeter Array (ALMA) Common Software (ACS) control middleware, with components implemented in Java, C++ and Python. The interfacing to the hardware is standardized via the Object Linking and Embedding for Process Control Unified Architecture (OPC UA). In order to access the OPC UA servers from the ACS framework in a common way, a library has been developed that allows to tie the OPC UA server nodes, methods and events to the equivalents in ACS components. The front-end of the archive system is able to identify the deployed components and to perform the sampling of the monitoring points of each component following time and value change triggers according to the selected configurations. The back-end of the archive system of the prototype is composed by two different databases: MySQL and MongoDB. MySQL has been selected as storage of the system configurations, while MongoDB is used to have an efficient storage of device monitoring data, CCD images, logging and alarm information. In this contribution, the details and conclusions on the implementation of the control software of the MST prototype are presented.

Fabrication of Reductive-Responsive Prodrug Nanoparticles with Superior Structural Stability by Polymerization-Induced Self-Assembly and Functional Nanoscopic Platform for Drug Delivery.

Science.gov (United States)

Zhang, Wen-Jian; Hong, Chun-Yan; Pan, Cai-Yuan

2016-09-12

A highly efficient strategy, polymerization-induced self-assembly (PISA) for fabrication of the polymeric drug delivery systems in cancer chemotherapy is reported. Diblock prodrug copolymer, PEG-b-P(MEO2MA-co-CPTM) was used as the macro-RAFT agent to fabricate prodrug nanoparticles through PISA. The advantages of fabricating intelligent drug delivery system via this approach are as following: (1) Simultaneous fulfillment of polymerization, self-assembly, and drug encapsulation in one-pot at relatively high concentration (100 mg/mL); (2) Almost complete monomer conversion allows direct application of the resultant prodrug nanoparticles without further purification; (3) Robust structures of the resultant prodrug nanoparticles, because the cross-linker was used as the comonomer, resulted in core-cross-linking simultaneously with the formation of the prodrug nanoparticles; (4) The drug content in the resultant prodrug nanoparticles can be accurately modulated just via adjusting the feed molar ratio of MEO2MA/CPTM in the synthesis of PEG-b-P(MEO2MA-co-CPTM). The prodrug nanoparticles with similar diameters but various drug contents were obtained using different prodrug macro-CTA. In consideration of the long-term biological toxicity, the prodrug nanoparticles with higher drug content exhibit more excellent anticancer efficiency due to that lower dosage of them are enough for effectively killing HeLa cells.

Polyaniline nanocomposites via in situ emulsion polymerization based on montmorillonite: Preparation and characterization

Directory of Open Access Journals (Sweden)

M.A. Abd El-Ghaffar

2015-11-01

Full Text Available Polyaniline nanocomposites were prepared via in situ emulsion polymerization in the presence of Na+ montmorillonite (Na+MMT. For achieving this purpose the clay was organophilized to (MMT-CTA form using cetyltrimethyl ammonium bromide (CTAB. The X-ray diffraction (XRD demonstrated that the basal space of Na+-montmorillonite increased after the organophilization from 11.21 to 19.35 Å. Polyaniline/montmorillonite (PAn/MMT nanocomposites were prepared by intercalating the emulsion of aniline monomer with treated organically layers of (Na+-MMT using ammonium peroxydisulfate (APS as an initiator. Furthermore aniline hydrochloride (AnHCl was used as a modifier and monomer to prepare PAn/H+MMT nanocomposites by cation exchange of the anilinuim moiety with the sodium ion inside the basal spaces which enlarged after the polymerization process to 35 Å as evidenced from X-ray diffraction (XRD. The d-spacing of the PAn/H+-MMT nanocomposite was found to become wider about 23.79 Å than that of the pure Na+-MMT, and successful intercalation or exfoliation of PAnH+ into Na+-MMT layers. The prepared PAn/MMT nanocomposites were characterized by thermal gravimetric analysis (TGA, scanning electron microscope (SEM, and transmission electron microscope (TEM. The electrical property measurements showed an enhancement in the conductivity values of the prepared nanocomposites especially on using AnHCl monomer to be in the order of 10−1 S/cm.

Role of CTA1R7K-COL-DD as a novel therapeutic mucosal tolerance-inducing vector for treatment of collagen-induced arthritis.

Science.gov (United States)

Hasselberg, Annemarie; Schön, Karin; Tarkowski, Andrej; Lycke, Nils

2009-06-01

To determine whether a cholera toxin-derived, novel immunomodulating fusion protein, CTA1R7K-COL-DD, carrying the class II major histocompatibility complex H-2q-restricted type II collagen peptide aa 259-274, can induce therapeutic tolerance and prevent collagen-induced arthritis (CIA) when administered intranasally in DBA/1 mice, and to assess whether ADP-ribosylation at the mucosal membranes exerts a regulatory function such that the outcome of tolerance or immune enhancement can be controlled. DBA/1 mice with CIA were treated intranasally with CTA1R7K-COL-DD. The therapeutic effect was monitored for 46 days after the onset of disease. Clinical scoring of disease, histologic examination of inflammation, and bone erosion were assessed, and cytokine levels were determined in the serum or supernatants from splenocytes stimulated with recall antigen. The protective effect of CTA1R7K-COL-DD resulted in roughly 60% of the mice having no clinical signs or histologic evidence of disease after treatment, and those with CIA had significantly milder disease with less bone erosion. The protective status was associated with lower serum titers of IgG1, IgG2a, IgG2b, and IgG3 anticollagen and a substantial decrease in the production of interleukin-6 (IL-6), IL-17, and interferon-gamma, while levels of IL-10 were markedly up-regulated both in the serum and at the T cell level. The enzymatically inactive mutant fusion protein CTA1R7K-COL-DD provided substantial therapeutic protection against CIA following intranasal administration. The mechanism behind the effect appears to be mediated by peptide-specific regulatory T cells induced by mucosal exposure to the peptide containing CTA1R7K-COL-DD vector. In addition, ADP-ribosylation at the mucosal membranes acts as a key regulator controlling mucosal tolerance or immunity.

Fully automatic detection and segmentation of abdominal aortic thrombus in post-operative CTA images using Deep Convolutional Neural Networks.

Science.gov (United States)

López-Linares, Karen; Aranjuelo, Nerea; Kabongo, Luis; Maclair, Gregory; Lete, Nerea; Ceresa, Mario; García-Familiar, Ainhoa; Macía, Iván; González Ballester, Miguel A

2018-05-01

Computerized Tomography Angiography (CTA) based follow-up of Abdominal Aortic Aneurysms (AAA) treated with Endovascular Aneurysm Repair (EVAR) is essential to evaluate the progress of the patient and detect complications. In this context, accurate quantification of post-operative thrombus volume is required. However, a proper evaluation is hindered by the lack of automatic, robust and reproducible thrombus segmentation algorithms. We propose a new fully automatic approach based on Deep Convolutional Neural Networks (DCNN) for robust and reproducible thrombus region of interest detection and subsequent fine thrombus segmentation. The DetecNet detection network is adapted to perform region of interest extraction from a complete CTA and a new segmentation network architecture, based on Fully Convolutional Networks and a Holistically-Nested Edge Detection Network, is presented. These networks are trained, validated and tested in 13 post-operative CTA volumes of different patients using a 4-fold cross-validation approach to provide more robustness to the results. Our pipeline achieves a Dice score of more than 82% for post-operative thrombus segmentation and provides a mean relative volume difference between ground truth and automatic segmentation that lays within the experienced human observer variance without the need of human intervention in most common cases. Copyright © 2018 Elsevier B.V. All rights reserved.

Hypoattenuation on CTA images with large vessel occlusion: timing affects conspicuity

Energy Technology Data Exchange (ETDEWEB)

Dave, Prasham [University of Ottawa, MD Program, Faculty of Medicine, Ottawa, ON (Canada); Lum, Cheemun; Thornhill, Rebecca; Chakraborty, Santanu [University of Ottawa, Department of Radiology, Ottawa, ON (Canada); Ottawa Hospital Research Institute, Ottawa, ON (Canada); Dowlatshahi, Dar [Ottawa Hospital Research Institute, Ottawa, ON (Canada); University of Ottawa, Division of Neurology, Department of Medicine, Ottawa, ON (Canada)

2017-05-15

Parenchymal hypoattenuation distal to occlusions on CTA source images (CTASI) is perceived because of the differences in tissue contrast compared to normally perfused tissue. This difference in conspicuity can be measured objectively. We evaluated the effect of contrast timing on the conspicuity of ischemic areas. We collected consecutive patients, retrospectively, between 2012 and 2014 with large vessel occlusions that had dynamic multiphase CT angiography (CTA) and CT perfusion (CTP). We identified areas of low cerebral blood volume on CTP maps and drew the region of interest (ROI) on the corresponding CTASI. A second ROI was placed in an area of normally perfused tissue. We evaluated conspicuity by comparing the absolute and relative change in attenuation between ischemic and normally perfused tissue over seven time points. The median absolute and relative conspicuity was greatest at the peak arterial (8.6 HU (IQR 5.1-13.9); 1.15 (1.09-1.26)), notch (9.4 HU (5.8-14.9); 1.17 (1.10-1.27)), and peak venous phases (7.0 HU (3.1-12.7); 1.13 (1.05-1.23)) compared to other portions of the time-attenuation curve (TAC). There was a significant effect of phase on the TAC for the conspicuity of ischemic vs normally perfused areas (P < 0.00001). The conspicuity of ischemic areas distal to a large artery occlusion in acute stroke is dependent on the phase of contrast arrival with dynamic CTASI and is objectively greatest in the mid-phase of the TAC. (orig.)

Effect of the different chain transfer agents on molecular weight and optical properties of poly(methyl methacrylate)

Science.gov (United States)

Çetinkaya, Onur; Demirci, Gökhan; Mergo, Paweł

2017-08-01

Investigation of molecular weight and optical properties of poly(methyl metacrylate) (PMMA) polymerized in house with different chain transfer agents was studied. Isopropyl alcohol (IPA), n-butyl mercaptan (nBMC) and pentamethyl disilane (PMDS) were used as chain transfer agents. The molecular weight (Mw) of PMMA samples were measured by Ostwald viscometer. Mw of bulk polymer samples were decreased with increase the concentration of chain transfer agents (CTA). Since reactivity of used CTAs is not same, molecular weights of samples which were produced with different type of CTA but same concentration of CTA was varied. Higher concentration of n-BMC showed higher scattering. Transmission of samples could not be correlated with different concentration of CTA. Refractive index of samples was not affected by concentration of CTA nevertheless higher molecular weight of CTA showed higher refractive index.

Differential diagnosis between aneurysm and infundibular dilatation in the IC-PC region with 3D-CTA

International Nuclear Information System (INIS)

Kubota, Tsukasa; Niwa, Jun; Tanigawara, Tetsuya; Chiba, Masahiko; Akiyama, Yukinori; Inamura Shigeru

2000-01-01

In cases of asymptomatic internal carotid-posterior communicating artery (IC-PC) protrusions, it is sometimes difficult to differentiate infundibular dilatation (ID) from aneurysm by digital subtraction angiography. We applied three-dimensional CT angiography (3D-CTA) in 32 cases of these IC-PC protrusions. SOMATOM PLUS 4 was used under such conditions as to provide images with high spatial resolution. The shaded surface display (SSD) method was adopted to reconstruct the 3D images because of its advantage in separating overlapped vasculature. We also made reference to source images and maximum intensity projection (MIP) to make sure of our diagnoses. In all cases including 4 aneurysms and 28 IDs, we were able to distinguish between ID and aneurysm. The accuracy of 3D-CTA was confirmed by 9 surgical cases. Our technique was as follows: To inject a high dose of diluted contrast medium rapidly to smaller arteries for opacification of contrast medium. To exclude neighboring useless structures except for the very close structures such as posterior clinoid process from the target image focusing on the IC-PC region. To observe the reconstructed image of MIP and SSD from various angles. The contralateral and craniocaudal view were valuable. To change the threshold level gradually and observe the configurational changes of the apex of protrusion. Poorly developed PcomA was mostly delineated at the optimum threshold level. Otherwise, the apex of protrusion remained spherical in an aneurysm and became pyramidal in shape in an ID when the threshold level was gradually decreased. In conclusion, 3D-CTA was a useful modality for IC-PC protrusions to distinguish between ID and aneurysm. (author)

DISCOVERY OF TeV GAMMA-RAY EMISSION FROM CTA 1 BY VERITAS

Energy Technology Data Exchange (ETDEWEB)

Aliu, E.; Errando, M. [Department of Physics and Astronomy, Barnard College, Columbia University, NY 10027 (United States); Archambault, S. [Physics Department, McGill University, Montreal, QC H3A 2T8 (Canada); Arlen, T. [Department of Physics and Astronomy, University of California, Los Angeles, CA 90095 (United States); Aune, T.; Bouvier, A. [Santa Cruz Institute for Particle Physics and Department of Physics, University of California, Santa Cruz, CA 95064 (United States); Beilicke, M.; Buckley, J. H.; Bugaev, V.; Dickherber, R. [Department of Physics, Washington University, St. Louis, MO 63130 (United States); Benbow, W. [Fred Lawrence Whipple Observatory, Harvard-Smithsonian Center for Astrophysics, Amado, AZ 85645 (United States); Cesarini, A.; Connolly, M. P. [School of Physics, National University of Ireland Galway, University Road, Galway (Ireland); Ciupik, L. [Astronomy Department, Adler Planetarium and Astronomy Museum, Chicago, IL 60605 (United States); Collins-Hughes, E. [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland); Cui, W. [Department of Physics, Purdue University, West Lafayette, IN 47907 (United States); Duke, C. [Department of Physics, Grinnell College, Grinnell, IA 50112-1690 (United States); Dumm, J. [School of Physics and Astronomy, University of Minnesota, Minneapolis, MN 55455 (United States); Dwarkadas, V. V. [Department of Astronomy and Astrophysics, University of Chicago, Chicago, IL 60637 (United States); Falcone, A., E-mail: muk@astro.columbia.edu, E-mail: smcarthur@ulysses.uchicago.edu [Department of Astronomy and Astrophysics, 525 Davey Lab, Pennsylvania State University, University Park, PA 16802 (United States); and others

2013-02-10

We report the discovery of TeV gamma-ray emission coincident with the shell-type radio supernova remnant (SNR) CTA 1 using the VERITAS gamma-ray observatory. The source, VER J0006+729, was detected as a 6.5 standard deviation excess over background and shows an extended morphology, approximated by a two-dimensional Gaussian of semimajor (semiminor) axis 0. Degree-Sign 30 (0. Degree-Sign 24) and a centroid 5' from the Fermi gamma-ray pulsar PSR J0007+7303 and its X-ray pulsar wind nebula (PWN). The photon spectrum is well described by a power-law dN/dE = N {sub 0}(E/3 TeV){sup -{Gamma}}, with a differential spectral index of {Gamma} = 2.2 {+-} 0.2{sub stat} {+-} 0.3{sub sys}, and normalization N {sub 0} = (9.1 {+-} 1.3{sub stat} {+-} 1.7{sub sys}) Multiplication-Sign 10{sup -14} cm{sup -2} s{sup -1} TeV{sup -1}. The integral flux, F {sub {gamma}} = 4.0 Multiplication-Sign 10{sup -12} erg cm{sup -2} s{sup -1} above 1 TeV, corresponds to 0.2% of the pulsar spin-down power at 1.4 kpc. The energetics, colocation with the SNR, and the relatively small extent of the TeV emission strongly argue for the PWN origin of the TeV photons. We consider the origin of the TeV emission in CTA 1.

Effects of automatic tube potential selection on radiation dose index, image quality, and lesion detectability in pediatric abdominopelvic CT and CTA: a phantom study

Energy Technology Data Exchange (ETDEWEB)

Brinkley, Michael F.; Choudhury, Kingshuk Roy; Frush, Donald P. [Duke University School of Medicine, Department of Radiology, DUMC Box 3808, Durham, NC (United States); Ramirez-Giraldo, Juan C. [Siemens Healthcare, Malvern (United States); Samei, Ehsan; Wilson, Joshua M.; Christianson, Olav I. [Duke University School of Medicine, Clinical Imaging Physics Group, Department of Radiology, Durham, NC (United States); Frush, Daniel J. [Duke University School of Medicine, Medical Physics, Durham, NC (United States)

2016-01-15

To assess the effect of automatic tube potential selection (ATPS) on radiation dose, image quality, and lesion detectability in paediatric abdominopelvic CT and CT angiography (CTA). A paediatric modular phantom with contrast inserts was examined with routine pitch (1.4) and high pitch (3.0) using a standard abdominopelvic protocol with fixed 120 kVp, and ATPS with variable kVp in non-contrast, contrast-enhanced, and CTA mode. The volume CT dose index (CTDI{sub vol}), contrast-to-noise ratio (CNR) and lesion detectability index (d') were compared between the standard protocol and ATPS examinations. CTDI{sub vol} was reduced in all routine pitch ATPS examinations, with dose reductions of 27-52 % in CTA mode (P < 0.0001), 15-33 % in contrast-enhanced mode (P = 0.0003) and 8-14 % in non-contrast mode (P = 0.03). Iodine and soft tissue insert CNR and d' were improved or maintained in all ATPS examinations. kVp and dose were reduced in 25 % of high pitch ATPS examinations and in none of the full phantom examinations obtained after a single full phantom localizer. ATPS reduces radiation dose while maintaining image quality and lesion detectability in routine pitch paediatric abdominopelvic CT and CTA, but technical factors such as pitch and imaging range must be considered to optimize ATPS benefits. (orig.)

Multimodal imaging in the elastase-induced aneurysm model in rabbits: a comparative study using serial DSA, MRA and CTA

International Nuclear Information System (INIS)

Doerfler, A.; Becker, W.; Wanke, I.; Goericke, S.; Oezkan, N.; Forsting, M.

2004-01-01

Background and Purpose: The elastase-induced aneurysm model in rabbits has proved to be suitable for testing new endovascular occlusion devices. The purpose of this study was to evaluate different imaging modalities for the depiction of anatomy and size of elastase-induced aneurysms and for serial follow-up imaging. Materials and Methods: Elastase-induced aneurysms were created in eight Chinchilla bastard rabbits by endoluminal incubation of porcine elastase. Serial imaging was performed using intravenous DSA (IVDSA), contrast-enhanced MRA (CEMRA), and time-of-flight MRA (TOF) 14 days, 4 weeks and 3 months after aneurysm creation. Intraarterial DSA (IADSA) and CT angiography (CTA) were performed after 3 months. Aneurysm size and geometry (height H, width W, neck width N) were compared. Results: On IVDSA after two weeks mean aneurysm height was 6.2 mm (range 2.8-11.0 mm), mean aneurysm neck width was 2.7 mm (range 2.0-4.2 mm) and mean aneurysm neck width was 2.7 mm (range 2.0-4.2 mm). We did not observed any statistically significant change in aneurysm dimensions during follow-up at 4 weeks (CEMRA: H: 5.4, W: 2.4, N: 2.4; TOF: H: 5.7, W: 2.4, N: 2.7) and 3 months (CEMRA: H: 5.8, W: 2.6, N: 2.6; TOF: H: 6.9, W: 2.8, N: 3.0). Aneurysm dimensions could be best seen on IADSA (H: 6.2, W: 3.0, N: 2.7) with good correlation to CTA (r=0.94; H: 6.1, W: 2.8, N: 2.6), CE-MRA (r=0.92), and TOF (r=0.97). TOF was superior to CEMRA in delineating the aneurysm wall. Conclusions: Serial imaging using MRA, CTA or intravenous and intraarterial angiography is feasible in the elastase-induced aneurysm model. Contrast-enhanced MRA, TOF-MRA and CTA showed good correlation to IADSA and are all suitable for non-invasive pretherapeutic measurement of aneurysm size. (orig.) [de

Búsqueda de Sitios para CTA: Análisis de Datos Satelitales

Science.gov (United States)

Suárez, A. E.; Medina, M. C.; Romero, G. E.

The CTA Consortium has decided to implement a systematic search for sites for the Observatory. This search will be made in two different steps. The first one consists of a general determination of the possible sites on the basis of some very basic selection criteria, such as geographic latitude, altitude and extension of the flat area needed. For those sites passing these criteria, a more intensive characterization should be made, using available satellite data, together with existing ground or air-based measurements. In this work we compare the behavior of different sites analyzing the aerosol content and the total precipitable water vapor, measured by MODIS instrument. FULL TEXT IN SPANISH

Radical-Mediated Enzymatic Polymerizations

Science.gov (United States)

Zavada, Scott R.; Battsengel, Tsatsral; Scott, Timothy F.

2016-01-01

Polymerization reactions are commonly effected by exposing monomer formulations to some initiation stimulus such as elevated temperature, light, or a chemical reactant. Increasingly, these polymerization reactions are mediated by enzymes―catalytic proteins―owing to their reaction efficiency under mild conditions as well as their environmental friendliness. The utilization of enzymes, particularly oxidases and peroxidases, for generating radicals via reduction-oxidation mechanisms is especially common for initiating radical-mediated polymerization reactions, including vinyl chain-growth polymerization, atom transfer radical polymerization, thiol–ene step-growth polymerization, and polymerization via oxidative coupling. While enzyme-mediated polymerization is useful for the production of materials intended for subsequent use, it is especially well-suited for in situ polymerizations, where the polymer is formed in the place where it will be utilized. Such polymerizations are especially useful for biomedical adhesives and for sensing applications. PMID:26848652

Halloysite nanotubes-polymeric nanocomposites: characteristics, modifications and controlled drug delivery approaches

Directory of Open Access Journals (Sweden)

P. C. Ferrari

Full Text Available Abstract Halloysite nanotubes (HNTs are aluminosilicate nanoclay mineral which have a hollow tubular structure and occurs naturally. They are biocompatible and viable carrier for inclusion of biologically active molecules due to the empty space inside the tubular structure. In this article, the HNTs main characteristics, and the HNTs-polymeric nanocomposite formation and their potential application as improvement of the mechanical performance of polymers and entrapment of hydrophilic and lipophilic substances are summarized. Recent works covering the increment of HNTs-polymeric nanocomposites and presenting promising employment of these systems as nanosized carrier, being suitable for pharmaceutical and biomedical applications, based on earlier evidence in literature of its nature to sustain the release of loaded drugs, presenting low cytotoxicity, and providing evidence for controlled drug delivery are reviewed.

Synthesis and utilization of poly (methylmethacrylate) nanocomposites based on modified montmorillonite

OpenAIRE

Youssef, Ahmed M.; Malhat, F.M.; Abdel Hakim, A.A.; Dekany, Imre

2015-01-01

Poly (methylmethacrylate) nanocomposite was prepared via in-situ emulsion polymerization (PMMA/Mt-CTA). The modified montmorillonite (Mt-CTA) is used as hosts for the preparation of poly (methylmethacrylate) nanocomposites with basal distance 1.95 nm. Moreover, exfoliated nanocomposite was characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), thermal gravimetric analysis (TGA), and differential scanning calorimetry (DSC). The fashioned nanocomposites exhibited bett...

35% Good Outcome Rate in IV-tPA treated Patients with CTA Confirmed Severe Anterior Circulation Occlusive Stroke

Science.gov (United States)

González, R. Gilberto; Furie, Karen L.; Goldmacher, Gregory V.; Smith, Wade S.; Kamalian, Shervin; Payabvash, Seyedmehdi; Harris, Gordon J.; Halpern, Elkan F.; Koroshetz, Walter J.; Camargo, Erica C. S.; Dillon, William P.; Lev, Michael H.

2015-01-01

BACKGROUND AND PURPOSE To determine the effect of IV-tPA on outcomes in patients with severe major anterior circulation ischemic stroke. METHODS Prospectively, 649 acute stroke patients had admission NIH stroke scale scores (NIHSS), non-contrast CT, CT angiography (CTA), and 6-month outcome assessed using modified Rankin scale (mRS). IV-tPA treatment decisions were made prior to CTA, at the time of non-contrast CT scanning, as per routine clinical protocol. Severe symptoms were defined as NIHSS>10. Poor outcome was defined as mRS>2. Major occlusions were identified on CTA. Univariate and multivariate stepwise-forward logistic regression analyses of the full cohort were performed. RESULTS Of 649 patients, 188 (29%) presented with NIHSS>10, and 64/188 (34%) of these received IV-tPA. Admission NIHSS, large artery occlusion, and IV-tPA all independently predicted good outcomes, however a significant interaction existed between IV-tPA and occlusion (p10 patients with anterior circulation occlusion, twice the percentage had good outcomes if they received IV-tPA (17/49, 35%), than if they did not (13/77, 17%; p=0.031). The “number needed to treat” was 7 (95% CI = 3–60). CONCLUSIONS IV-tPA treatment resulted in significantly more good outcomes in severely symptomatic stroke patients with major anterior circulation occlusions. The 35% good outcome rate was similar to rates found in endovascular therapy trials. Vascular imaging may help in patient selection and stratification for trials of IV-thrombolytic and endovascular therapies. PMID:24003051

Probing for Pulsars: An XMM Study of the Composite SNRS G327.1-1.1 and CTA1

Science.gov (United States)

Slane, Patrick; Mushotzky, Richard F. (Technical Monitor)

2003-01-01

The subject grant is for analysis of XMM data from the supernova remnant CTA1. Our investigation centered on the study of the compact source Rx 50007.0+7302 that, based on our previous observations, appears to be a neutron star powering a wind nebula in the remnant interior. This compact source has also been suggested as the counterpart of the EGRET source 2EG J0008+7307. The analysis of the data from the compact source is complete. We find that the spectrum of the source is well described by a power law with the addition of a soft thermal component that may correspond to emission from hot polar cap regions or to cooling emission from a light element atmosphere over the entire star. There is evidence of extended emission on small spatial scales which may correspond to structure in the underlying synchrotron nebula. Extrapolation of the nonthermal emission component to gamma-ray energies yields a flux that is consistent with that of 2EG J0008+7307, thus strengthening the proposition that there is a gamma-ray emitting pulsar at the center of CTA 1. Our timing studies with the EPIC pn data revealed no evidence for pulsations, however; we set an upper limit of 61% on the pulsed fraction from this source. The results from this study were presented in a poster at the recent IAU Symposium in Sydney, Australia. A paper summarizing these results, entitled "Xray Observations of the Compact Source in CTA 1" (Slane et al.) has been submitted for publication in the Astrophysical Journal.

Automated identification of best-quality coronary artery segments from multiple-phase coronary CT angiography (cCTA) for vessel analysis

Science.gov (United States)

Zhou, Chuan; Chan, Heang-Ping; Hadjiiski, Lubomir M.; Chughtai, Aamer; Wei, Jun; Kazerooni, Ella A.

2016-03-01

We are developing an automated method to identify the best quality segment among the corresponding segments in multiple-phase cCTA. The coronary artery trees are automatically extracted from different cCTA phases using our multi-scale vessel segmentation and tracking method. An automated registration method is then used to align the multiple-phase artery trees. The corresponding coronary artery segments are identified in the registered vessel trees and are straightened by curved planar reformation (CPR). Four features are extracted from each segment in each phase as quality indicators in the original CT volume and the straightened CPR volume. Each quality indicator is used as a voting classifier to vote the corresponding segments. A newly designed weighted voting ensemble (WVE) classifier is finally used to determine the best-quality coronary segment. An observer preference study is conducted with three readers to visually rate the quality of the vessels in 1 to 6 rankings. Six and 10 cCTA cases are used as training and test set in this preliminary study. For the 10 test cases, the agreement between automatically identified best-quality (AI-BQ) segments and radiologist's top 2 rankings is 79.7%, and between AI-BQ and the other two readers are 74.8% and 83.7%, respectively. The results demonstrated that the performance of our automated method was comparable to those of experienced readers for identification of the best-quality coronary segments.

Elektroaktive polymerer

DEFF Research Database (Denmark)

West, K.

Traditionelt tænker vi på polymerer (plastik) som elektrisk isolerende materialer - det som er udenpå ledningerne. I dag kender vi imidlertid også polymerer med intrinsisk elektrisk ledningsevne, og plast er på vej ind i anvendelser, der tidligereudelukkende var baseret på metaller og uorganiske...... halvledere. Hertil kommer, at en del af de ledende polymerer kan stimuleres til at skifte mellem en ledende og en halvledende tilstand, hvorved de ændret både form og farve. I foredraget gives der enrække eksempler på anvendelse af polymerer som elektriske komponenter - rækkende fra polymer elektronik over...

SYNTHESIS AND EVALUATION OF β-CYCLODEXTRIN-EPICHLOROHYDRIN INCLUSION COMPLEX AS A PHARMACEUTICAL EXCIPIENT

Directory of Open Access Journals (Sweden)

K. N. Poornima

2015-05-01

Full Text Available A water soluble Beta-cyclodextrin-epichlorohydrin complex (Beta-CDEPI was synthesized by one-step condensation polymerization. Drug- Beta-CDEPI inclusion complexes were prepared and characterized. Inclusion complexes prepared using lyophilization technique was used to formulate orodispersible tablets. Compatibility studies showed no interaction and characterization proved substantial inclusion complex formation. Drug content was found between 97-99%. In-vitro disintegration time was found to be less than 3 minutes and all the formulations showed complete drug release of 100% within 15 minutes. The formulations were found to be stable for a period of 6 months. Beta-CDEPI polymer enhances the solubility and thus effectively can be utilized to improve the aqueous solubility of poorly water soluble drugs.

ACID Astronomical and Physics Cloud Interactive Desktop: A Prototype of VUI for CTA Science Gateway

Science.gov (United States)

Massimino, P.; Costa, A.; Becciani, U.; Vuerli, C.; Bandieramonte, M.; Petta, C.; Riggi, S.; Sciacca, E.; Vitello, F.; Pistagna, C.

2014-05-01

The Astronomical & Physics Cloud Interactive Desktop, developed for the prototype of CTA Science Gateway in Catania, Italy, allows to use many software packages without any installation on the local desktop. The users will be able to exploit, if applicable, the native Graphical User Interface (GUI) of the programs that are available in the ACID environment. For using interactively the remote programs, ACID exploits an "ad hoc" VNC-based User Interface (VUI).

Estimation of center line and diameter of brain blood vessel using three-dimensional blood vessel matching method with head three-dimensional CTA image

International Nuclear Information System (INIS)

Maekawa, Masashi; Shinohara, Toshihiro; Nakayama, Masato; Nakasako, Noboru

2010-01-01

To support and automate the brain blood vessel disease diagnosis, a novel method to obtain the center line and the diameter of a blood vessel is proposed with a three-dimensional head computed tomographic angiography (CTA) image. Although the line thinning processing with distance transform or gray information is generally used to obtain the blood vessel center line, this method is not essentially one to obtain the center line and tends to yield extra lines depending on CTA images. In this study, the center line of the blood vessel is obtained by tracing the vessel. The blood vessel is traced by sequentially estimating the center point and direction of the blood vessel. The center point and direction of the blood vessel are estimated by taking the correlation between the blood vessel and a solid model of the blood vessel that is designed by considering noise influence. In addition, the vessel diameter is also estimated by correlating the blood vessel and the blood vessel model of which the diameter is variable. The validity of the proposed method is confirmed by experimentally applied the proposed method to an actual three-dimensional head CTA image. (author)

A One-Step Route to CO2 -Based Block Copolymers by Simultaneous ROCOP of CO2 /Epoxides and RAFT Polymerization of Vinyl Monomers.

Science.gov (United States)

Wang, Yong; Zhao, Yajun; Ye, Yunsheng; Peng, Haiyan; Zhou, Xingping; Xie, Xiaolin; Wang, Xianhong; Wang, Fosong

2018-03-26

The one-step synthesis of well-defined CO 2 -based diblock copolymers was achieved by simultaneous ring-opening copolymerization (ROCOP) of CO 2 /epoxides and RAFT polymerization of vinyl monomers using a trithiocarbonate compound bearing a carboxylic group (TTC-COOH) as the bifunctional chain transfer agent (CTA). The double chain-transfer effect allows for independent and precise control over the molecular weight of the two blocks and ensures narrow polydispersities of the resultant block copolymers (1.09-1.14). Notably, an unusual axial group exchange reaction between the aluminum porphyrin catalyst and TTC-COOH impedes the formation of homopolycarbonates. By taking advantage of the RAFT technique, it is able to meet the stringent demand for functionality control to well expand the application scopes of CO 2 -based polycarbonates. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Radiation chemistry of polymeric system

International Nuclear Information System (INIS)

Machi, Sueo; Ishigaki, Isao

1978-01-01

Among wide application of radiation in the field of polymer chemistry, practices of polymerization, graft polymerization, bridging, etc. are introduced hereinafter. As for the radiation sources of radiation polymerization, in addition to the 60 Co-γ ray with long permeation distance which has been usually applied, electron beam accelerators with high energy, large current and high reliability have come to be produced, and the liquid phase polymerization by electron beam has attracted attention industrially. Concerning polymerizing reactions, explanations were given to electron beam polymerization under high dose rate, the polymerization in supercooling state or under high pressure, and emulsifying polymerization. As for radiation bridging, radiation is applied for the bridging of hydrogel, acceleration of bridging and improvement of radiation resistance. It is also utilized for reforming membranes by graft polymerization, and synthesis of polymers for medical use. Application of fixed enzymes in the medical field has been investigated by fixing various enzymes by low temperature γ-ray polymerization with glassy monomers such as HEMA. (Kobatake, H.)

The CTA Sensitivity to Lorentz-Violating Effects on the Gamma-Ray Horizon

CERN Document Server

Fairbairn, Malcolm; Ellis, John; Hinton, Jim; White, Richard

2014-01-01

The arrival of TeV-energy photons from distant galaxies is expected to be affected by their QED interaction with intergalactic radiation fields through electron-positron pair production. In theories where high-energy photons violate Lorentz symmetry, the kinematics of the process $\\gamma + \\gamma\\rightarrow e^+ + e^-$ is altered and the cross-section suppressed. Consequently, one would expect more of the highest-energy photons to arrive if QED is modified by Lorentz violation than if it is not. We estimate the sensitivity of Cherenkov Telescope Array (CTA) to changes in the $\\gamma$-ray horizon of the Universe due to Lorentz violation, and find that it should be competitive with other leading constraints.

Optimization of pulverised coal combustion by means of CFD/CTA modeling

Directory of Open Access Journals (Sweden)

Filkoski Risto V.

2006-01-01

Full Text Available The objective of the work presented in this paper was to apply a method for handling two-phase reacting flow for prediction of pulverized coal combustion in large-scale boiler furnace and to assess the ability of the model to predict existing power plant data. The paper presents the principal steps and results of the numerical modeling of power boiler furnace with tangential disposition of the burners. The computational fluid dynamics/computational thermal analysis (CFD/CTA approach is utilized for creation of a three-dimensional model of the boiler furnace, including the platen superheater in the upper part of the furnace. Standard k-e model is employed for description of the turbulent flow. Coal combustion is modeled by the mixture fraction/probability density function approach for the reaction chemistry, with equilibrium assumption applied for description of the system chemistry. Radiation heat transfer is computed by means of the simplified P-N model, based on the expansion of the radiation intensity into an orthogonal series of spherical harmonics. Some distinctive results regarding the examined boiler performance in capacity range between 65 and 95% are presented graphically. Comparing the simulation predictions and available site measurements concerning temperature, heat flux and combustion efficiency, a conclusion can be drawn that the model produces realistic insight into the furnace processes. Qualitative agreement indicates reasonability of the calculations and validates the employed sub-models. After the validation and verification of the model it was used to check the combustion efficiency as a function of coal dust sieve characteristics, as well as the impact of burners modification with introduction of over fire air ports to the appearance of incomplete combustion, including CO concentration, as well as to the NOx concentration. The described case and other experiences with CFD/CTA stress the advantages of numerical modeling and

System testing software deployments using Docker and Kubernetes in gitlab CI: EOS + CTA use case

CERN Document Server

CERN. Geneva

2017-01-01

It needs to be seamlessly integrated with `EOS`, which has become the de facto disk storage system at CERN. `CTA` and `EOS` integration requires parallel development of features in both software that needs to be **synchronized and systematically tested** on a specific distributed development infrastructure for each commit in the code base. This presentation describes the full gitlab continuous integration work flow that builds, tests, deploys and run system tests of the full software stack in docker containers on our specific kubernetes infrastructure.

Twin screw extruders as polymerization reactors for a free radical homo polymerization

NARCIS (Netherlands)

Ganzeveld, K.J.; Janssen, L.P.B.M.

The bulk polymerization of n-butylmethacrylate was investigated in a counter-rotating twin screw extruder. It appeared that the gel effect, occurring with bulk polymerizations, affected the polymerization progress very strongly. Due to this effect the conversion of the reaction is independent of the

Mechanocatalytic polymerization and cross-linking in a polymeric matrix

NARCIS (Netherlands)

Jakobs, R.T.M.; Ma, Shuang; Sijbesma, R.P.

2013-01-01

A latent olefin metathesis catalyst, bearing two polymeric NHC ligands, was embedded in a semicrystalline polymer matrix containing cyclic olefins. The catalyst was activated by straining the solid material under compression, resulting in polymerization and cross-linking reactions of the monomers in

Efficiency of polymerization of bulk-fill composite resins: a systematic review.

Science.gov (United States)

Reis, André Figueiredo; Vestphal, Mariana; Amaral, Roberto Cesar do; Rodrigues, José Augusto; Roulet, Jean-François; Roscoe, Marina Guimarães

2017-08-28

This systematic review assessed the literature to evaluate the efficiency of polymerization of bulk-fill composite resins at 4 mm restoration depth. PubMed, Cochrane, Scopus and Web of Science databases were searched with no restrictions on year, publication status, or article's language. Selection criteria included studies that evaluated bulk-fill composite resin when inserted in a minimum thickness of 4 mm, followed by curing according to the manufacturers' instructions; presented sound statistical data; and comparison with a control group and/or a reference measurement of quality of polymerization. The evidence level was evaluated by qualitative scoring system and classified as high-, moderate- and low- evidence level. A total of 534 articles were retrieved in the initial search. After the review process, only 10 full-text articles met the inclusion criteria. Most articles included (80%) were classified as high evidence level. Among several techniques, microhardness was the most frequently method performed by the studies included in this systematic review. Irrespective to the "in vitro" method performed, bulk fill RBCs were partially likely to fulfill the important requirement regarding properly curing in 4 mm of cavity depth measured by depth of cure and / or degree of conversion. In general, low viscosities BFCs performed better regarding polymerization efficiency compared to the high viscosities BFCs.

Chelating polymeric membranes

KAUST Repository

Peinemann, Klaus-Viktor; Villalobos Vazquez de la Parra, Luis Francisco; Hilke, Roland

2015-01-01

microporous chelating polymeric membrane. Embodiments include, but are not limited to, microporous chelating polymeric membranes, device comprising the membranes, and methods of using and making the same.

Coronary plaque property evaluation by coronary CTA and its correlation with inflammatory molecules and MMPs/TIMPs

Directory of Open Access Journals (Sweden)

Wen-Bing Yang

2017-11-01

Full Text Available Objective: To study the evaluation value of coronary CTA for coronary plaque properties and its correlation with inflammatory molecules and MMPs/TIMPs. Methods: Patients who were diagnosed with acute coronary syndrome in Renmin Hospital of Wuhan University between August 2014 and December 2016 were selected as the ACS group of the research, patients who were diagnosed with stable angina pectoris were selected as the SAP group of the research, and healthy subjects who received physical examination during the same period were selected as the control group of the research. Coronary CTA was done to determine the coronary plaque properties of ACS group, and serum was collected from the three groups of subjects to determine the contents of inflammatory molecules and MMPs/TIMPs collagen metabolites. Results: Serum MIP-1α, MCP-1, sFGL-2, sCD14, CXCL5, I-CTP, III-CTP and EMMPRIN contents of ACS group and SAP group were higher than those of control group while TIMP1, TIMP2 contents were lower than those of control group; serum MIP-1α, MCP-1, sFGL-2, sCD14, CXCL5, I-CTP, III-CTP and EMMPRIN contents of ACS group were higher than those of SAP group while TIMP1 and TIMP2 contents were lower than those of SAP group. Serum MIP-1α, MCP-1, sFGL-2, sCD14, CXCL5, I-CTP, III-CTP and EMMPRIN contents of ACS patients with soft plaque and fibrous plaque were higher than those of ACS patients with calcified plaque while TIMP1 and TIMP2 contents were lower than those of ACS patients with calcified plaque; serum MIP-1α, MCP-1, sFGL-2, sCD14, CXCL5, I-CTP, III-CTP and EMMPRIN contents of ACS patients with soft plaque were higher than those of ACS patients with fibrous plaque while TIMP1, TIMP2 contents were lower than those of ACS patients with fibrous plaque. Conclusion: The coronary plaque property evaluation by coronary CTA is closely related to the changes of inflammatory response and MMPs/TIMPs collagen metabolism.

Evaluation value of coronary CTA for coronary plaque features and its correlation with platelet function and serum biochemical indexes

Directory of Open Access Journals (Sweden)

Jin-Xia Yang

2017-01-01

Full Text Available Objective: To analyze the evaluation value of coronary CT angiography for coronary plaque features and its correlation with platelet function and serum biochemical indexes. Methods: A total of 450 patients with coronary heart disease were divided into calcified plaque group (CT value≥130HU (n=117, soft plaque group (CT value≤60HU (n=150 and mixed plaque group (CT value 60-130HU (n=183 by coronary CT angiography (CTA, and 100 healthy subjects who received physical examination in our hospital during the same period were selected as control group. Differences in platelet function and serum biochemical indexes were compared among four groups of patients, and the judgment value of atheromatous plaque CT value from CTA for the severity of coronary heart disease was analyzed. Results: Platelet function parameters MPV, TEG-MA, P-selectin, PDGF-BB and vWF levels in peripheral blood of soft plaque group were higher than those of the other three groups; inflammatory factors CRP, IL-6, IL-12, IL-18 and IL-23 content in serum were higher than those of the other three groups; chemokines MCP-1, CXCL16, Fractalkine and RANTES content in serum were higher than those of the other three groups; adipocytokines Leptin and RBP4 content in serum were higher than those of the other three groups while SFRP5 content was lower than those of the other three groups. Atheromatous plaque CT value in patients with coronary heart disease was directly correlated with platelet function and the content of serum biochemical indexes. Conclusions: Coronary CTA can accurately assess coronary atheromatous plaque features, and can also be a reliable noninvasive method to judge coronary heart disease severity, treatment prognosis and so on.

Self-Assembled Polymeric Micellar Nanoparticles as Nanocarriers for Poorly Soluble Anticancer Drug Ethaselen

Directory of Open Access Journals (Sweden)

Yang Zhuoli

2009-01-01

Full Text Available Abstract A series of monomethoxy poly(ethylene glycol-poly(lactide (mPEG-PLA diblock copolymers were synthesized, and mPEG-PLA micelle was fabricated and used as a nanocarrier for solubilization and delivery of a promising anticancer drug ethaselen. Ethaselen was efficiently encapsulated into the micelles by the dialysis method, and the solubility of ethaselen in water was remarkably increased up to 82 μg/mL before freeze-drying. The mean diameter of ethaselen-loaded micelles ranged from 51 to 98 nm with a narrow size distribution and depended on the length of PLA block. In vitro hemolysis study indicated that mPEG-PLA copolymers and ethaselen-loaded polymeric micelles had no hemolytic effect on the erythrocyte. The enhanced antitumor efficacy and reduced toxic effect of ethaselen-loaded polymeric micelle when compared with ethaselen-HP-β-CD inclusion were observed at the same dose in H22human liver cancer cell bearing mouse models. These suggested that mPEG-PLA polymeric micelle nanoparticles had great potential as nanocarriers for effective solubilization of poorly soluble ethaselen and further reducing side effects and toxicities of the drug.

Polymeric micelles for drug targeting.

Science.gov (United States)

Mahmud, Abdullah; Xiong, Xiao-Bing; Aliabadi, Hamidreza Montazeri; Lavasanifar, Afsaneh

2007-11-01

Polymeric micelles are nano-delivery systems formed through self-assembly of amphiphilic block copolymers in an aqueous environment. The nanoscopic dimension, stealth properties induced by the hydrophilic polymeric brush on the micellar surface, capacity for stabilized encapsulation of hydrophobic drugs offered by the hydrophobic and rigid micellar core, and finally a possibility for the chemical manipulation of the core/shell structure have made polymeric micelles one of the most promising carriers for drug targeting. To date, three generations of polymeric micellar delivery systems, i.e. polymeric micelles for passive, active and multifunctional drug targeting, have arisen from research efforts, with each subsequent generation displaying greater specificity for the diseased tissue and/or targeting efficiency. The present manuscript aims to review the research efforts made for the development of each generation and provide an assessment on the overall success of polymeric micellar delivery system in drug targeting. The emphasis is placed on the design and development of ligand modified, stimuli responsive and multifunctional polymeric micelles for drug targeting.

Polymerization Using Phosphazene Bases

KAUST Repository

Zhao, Junpeng

2015-09-01

In the recent rise of metal-free polymerization techniques, organic phosphazene superbases have shown their remarkable strength as promoter/catalyst for the anionic polymerization of various types of monomers. Generally, the complexation of phosphazene base with the counterion (proton or lithium cation) significantly improves the nucleophilicity of the initiator/chain end resulting in highly enhanced polymerization rates, as compared with conventional metalbased initiating systems. In this chapter, the general features of phosphazenepromoted/catalyzed polymerizations and the applications in macromolecular engineering (synthesis of functionalized polymers, block copolymers, and macromolecular architectures) are discussed with challenges and perspectives being pointed out.

Phosphazene-promoted anionic polymerization

KAUST Repository

Zhao, Junpeng

2014-01-01

In the recent surge of metal-free polymerization techniques, phosphazene bases have shown their remarkable potential as organic promoters/catalysts for the anionic polymerization of various types of monomers. By complexation with the counterion (e.g. proton or lithium cation), phosphazene base significantly improve the nucleophilicity of the initiator/chain-end resulting in rapid and usually controlled anionic/quasi-anionic polymerization. In this review, we will introduce the general mechanism, i.e. in situ activation (of initiating sites) and polymerization, and summarize the applications of such a mechanism on macromolecular engineering toward functionalized polymers, block copolymers and complex macromolecular architectures.

Electrodriven selective transport of Cs+ using chlorinated cobalt dicarbollide in polymer inclusion membrane: a novel approach for cesium removal from simulated nuclear waste solution.

Science.gov (United States)

Chaudhury, Sanhita; Bhattacharyya, Arunasis; Goswami, Asok

2014-11-04

The work describes a novel and cleaner approach of electrodriven selective transport of Cs from simulated nuclear waste solutions through cellulose tri acetate (CTA)/poly vinyl chloride (PVC) based polymer inclusion membrane. The electrodriven cation transport together with the use of highly Cs+ selective hexachlorinated derivative of cobalt bis dicarbollide, allows to achieve selective separation of Cs+ from high concentration of Na+ and other fission products in nuclear waste solutions. The transport selectivity has been studied using radiotracer technique as well as atomic emission spectroscopic technique. Transport studies using CTA based membrane have been carried out from neutral solution as well as 0.4 M HNO3, while that with PVC based membrane has been carried out from 3 M HNO3. High decontamination factor for Cs+ over Na+ has been obtained in all the cases. Experiment with simulated high level waste solution shows selective transport of Cs+ from most of other fission products also. Significantly fast Cs+ transport rate along with high selectivity is an interesting feature observed in this membrane. The current efficiency for Cs+ transport has been found to be ∼100%. The promising results show the possibility of using this kind of electrodriven membrane transport methods for nuclear waste treatment.

Conducting Polymeric Materials

DEFF Research Database (Denmark)

Hvilsted, Søren

2016-01-01

The overall objective of this collection is to provide the most recent developments within the various areas of conducting polymeric materials. The conductivity of polymeric materials is caused by electrically charged particles, ions, protons and electrons. Materials in which electrons...

Sociodemographic and behavioral aspects of HIV positive individuals from a HIV/STD counseling and testing center (CTA in the city of Belém, Pará

Directory of Open Access Journals (Sweden)

Rodolfo Gomes Nascimento

2014-04-01

Full Text Available Backgound and Objectives: The Testing and Counseling Center’s (CTA are characterized for offer actions directed toward HIV testing and counseling pretest and after test that the systematic collection of information involves allowing to know important characteristics epidemiologists and behaviors associates to the HIV seropositivity of the users of the service. This study it had as objective to describe the sociodemographic and behavioral aspects of the users with positive serology taken care of in the biggest CTA of the state of Pará, between 2008 and 2010. Methods: The collection and analysis of data had been carried through on the basis of the System of information of CTA (SI-CTA, in the serological tests and interviews of 547 HIV infected users respecting all the ethical rules. Results: in relation to the epidemiological features, 60.6% were men, with average of age of 33,4 years, 54.2% were single, in the majority medium brown (77.6%, with education of 8 to the 11 years (54% and in the majority heterosexuals (64,3%. In relation to the use of condoms, 53.7% (IC95% 33,4; 41,7 with fixed partnership and 40.2 (IC95% 14,5; 21,1 with eventual partnerships had told not the use of condoms in the sexual relations. Amongst the main reasons for the use of condoms they had not been distinguished it confidence in the partner, the non-availability at the moment of the relation and other reasons. Conclusion: The results suggest that even so it has similarities in relation to the current trend of the epidemic of HIV/Aids, exist peculiarities in our region that deserve differentiated preventive interventions. KEYWORDS: HIV Infections. Epidemiology. HIV Seroprevalence.

Synthesis and utilization of poly (methylmethacrylate nanocomposites based on modified montmorillonite

Directory of Open Access Journals (Sweden)

Ahmed M. Youssef

2017-07-01

Full Text Available Poly (methylmethacrylate nanocomposite was prepared via in-situ emulsion polymerization (PMMA/Mt-CTA. The modified montmorillonite (Mt-CTA is used as hosts for the preparation of poly (methylmethacrylate nanocomposites with basal distance 1.95 nm. Moreover, exfoliated nanocomposite was characterized by X-ray diffraction (XRD, transmission electron microscope (TEM, thermal gravimetric analysis (TGA, and differential scanning calorimetry (DSC. The fashioned nanocomposites exhibited better thermal stability than pristine PMMA which make it suitable for packaging applications. Furthermore, this nanocomposite reveals tremendous affinity for removing pesticides from aquatic solutions. The data obtained from GC/ECD gas liquid chromatography illustrated that the removal efficiency of PMMA/Mt-CTA nanocomposites for organochlorine pesticides (OCPs varied from 73.65% to 99.36% that make it as a new method for water treatment. Also, the antimicrobial activity of the Mt-CTA and PMMA/Mt-CTA nanocomposites was evaluated by the inhibitory zone tests and revealed good activity against Escherichia coli and Staphylococcus aureus, which makes it suitable materials for packaging applications.

Carotid body size on CTA: Correlation with comorbidities

International Nuclear Information System (INIS)

Cramer, J.A.; Wiggins, R.H.; Fudim, M.; Engelman, Z.J.; Sobotka, P.A.; Shah, L.M.

2014-01-01

Aim: To test the hypothesis that computed tomographic angiography (CTA) can identify carotid body enlargement in patients with sympathetically mediated diseases. Materials and methods: A retrospective chart review of all patients obtaining CTAs of the cervical vasculature at University of Utah Health Sciences Center over a 6-month period was performed. Widest axial measurements of both carotid bodies were performed on a picture archiving and communication system (PACS). Statistical analysis was then performed to compare the mean carotid body size between control patients and patients with diabetes mellitus, hypertension, and congestive heart failure. Results: Measurements were performed on 288 patients, with 134 controls. Of the remaining 154, 72 patients had diabetes mellitus, 46 had congestive heart failure, and 130 had hypertension. The control patients had a mean carotid body diameter of 2.3 mm. There was a statistically significant (p < 0.01) 20–25% increase in mean diameter with diabetes mellitus (2.8 mm), hypertension (2.7 mm), and congestive heart failure (2.7 mm; p < 0.01). Conclusions: This study found a 20–25% larger mean carotid body size in patients with diabetes mellitus, hypertension, and congestive heart failure relative to controls. However, this small enlargement should not mimic other carotid body diseases, such as a paraganglionoma. Moreover, these findings further support the proposed functional relationship between the carotid body and sympathetically mediated disease states

Applied bioactive polymeric materials

CERN Document Server

Carraher, Charles; Foster, Van

1988-01-01

The biological and biomedical applications of polymeric materials have increased greatly in the past few years. This book will detail some, but not all, of these recent developments. There would not be enough space in this book to cover, even lightly, all of the major advances that have occurred. Some earlier books and summaries are available by two of this book's Editors (Gebelein & Carraher) and these should be consul ted for additional information. The books are: "Bioactive Polymeric Systems" (Plenum, 1985); "Polymeric Materials In Medication" (Plenum, 1985); "Biological Acti vi ties of Polymers" (American Chemical Society, 1982). Of these three, "Bioacti ve Polymeric Systems" should be the most useful to a person who is new to this field because it only contains review articles written at an introductory level. The present book primarily consists of recent research results and applications, with only a few review or summary articles. Bioactive polymeric materials have existed from the creation of life...

Radiation induced emulsion polymerization

International Nuclear Information System (INIS)

Stannett, V.T.; Stahel, E.P.

1990-01-01

High energy radiation is particularly favored for the initiation of emulsion polymerization. The yield of free radicals, for example, from the radiolysis of the aqueous phase, is high; G(radical) values of 5-7. In addition, the rather special kinetics associated with emulsion polymerization lead, in general, to very large kinetic chain lengths, even with 'non-ideal' monomers such as vinyl acetate. Together, high polymerization rates at low doses become possible. There are some important advantages of radiation polymerization compared with chemical initiators, such as potassium persulfate. Perhaps the most important among them is the temperature independence of the initiation step. This makes low temperature polymerization very accessible. With monomers such as vinyl acetate, where chain termination to monomer is predominant, low temperatures lead to often highly desirable higher molecular weights. With styrene, the classical ideally behaved monomer, there are the advantages such as, for example, the feasibility of using cationic monomers. These and some attendant disadvantages are discussed in detail, including pilot plant studies

Audit of CT reporting standards in cases of intracerebral haemorrhage at a comprehensive stroke centre in Australia.

Science.gov (United States)

Barras, Christen D; Asadi, Hamed; Phal, Pramit M; Tress, Brian M; Davis, Stephen M; Desmond, Patricia M

2016-12-01

Multiple CT-derived biomarkers that are predictive of intracerebral haemorrhage (ICH) growth and outcome have been described in the literature, but the extent to which these appear in imaging reports of ICH is unknown. The aim of this retrospective process audit was to determine which of the known predictors of ICH outcome was recorded in reports of the disease, with a view to providing reporting recommendations, as appropriate. We examined the initial CT report of patients diagnosed with ICH presenting to a metropolitan comprehensive stroke centre and meeting inclusion criteria during the audit period between 1 March 2013 and 28 February 2014. Each report was assessed for the inclusion of the following ICH characteristics: the number of measurement dimensions; volume; location; hydrocephalus; shape; density; 'CTA spot sign' (where CTA was performed). A total of 100 patients met audit inclusion criteria. At least one ICH dimension was recorded in 90% of reports; however, 39% did not include the measurements in three dimensions and volume was reported in just 6%. No ICH dimension was recorded in 10% of reports. With the exception of density and shape, reporting of other CT features exceeded 95%. Where CTA was performed (58%), 14 (24%) of 58 reported the 'CTA spot sign' status. In this audit, volume was the most under-reported of the established ICH characteristics predictive of ICH outcome. Readily calculated from multiplanar reformats using the ABC/2 technique, the routine reporting of ICH volume is recommended. More reporting attention to ICH density heterogeneity and shape irregularity is encouraged, given their emerging importance. Where acute CTA is performed, the presence of any dynamic haemorrhage (CTA spot sign) should be reported. © 2016 The Royal Australian and New Zealand College of Radiologists.

Carboxyl-Functionalized Polymeric Microspheres Prepared by One-Stage Photoinitiated RAFT Dispersion Polymerization

Directory of Open Access Journals (Sweden)

Jianbo Tan

2017-12-01

Full Text Available Herein, we report a photoinitiated reversible addition-fragmentation chain transfer (RAFT dispersion copolymerization of methyl methacrylate (MMA and methyl methacrylic (MAA for the preparation of highly monodisperse carboxyl-functionalized polymeric microspheres. High rates of polymerization were observed, with more than 90% particle yields being achieved within 3 h of UV irradiation. Effects of reaction parameters (e.g., MAA concentration, RAFT agent concentration, photoinitiator concentration, and solvent composition were studied in detail, and highly monodisperse polymeric microspheres were obtained in most cases. Finally, silver (Ag composite microspheres were prepared by in situ reduction of AgNO3 using the carboxyl-functionalized polymeric microspheres as the template. The obtained Ag composite microspheres were able to catalyze the reduction of methylene blue (MB with NaBH4 as a reductant.

"Click" i polymerer 2

DEFF Research Database (Denmark)

Hvilsted, Søren

2012-01-01

"Click"-reaktioner til fremstilling af ledende polymerer med funktionelle håndtag og bipolymermaterialer......"Click"-reaktioner til fremstilling af ledende polymerer med funktionelle håndtag og bipolymermaterialer...

Survey and research on precision polymerization polymeric materials; Seimitsu jugo kobunshi zairyo ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Survey and research on the precision control of primary structure of polymeric materials and the precision evaluation technology have been conducted to develop advanced polymeric materials. It is proposed that the three basic processes of polymer synthesis, i.e., addition, condensation, and biomimesis, in forming the precision polymerization skeleton are to be covered through a centralized joint research effort with participation of industry, academia, and the government institute and under the leadership of researchers from academic institutions as the team leaders. For the study of technology trends, international conferences held in UK, Germany, and Hawaii are introduced, and domestic meetings, i.e., Annual Polymer Congress and Polymer Conference, are summarized. In addition, Precision Polymerization Forum and International Workshop on Precision Polymerization were held. The basic studies include a quantum-chemical elucidation of the elementary process in polymerization reaction, time-resolved analysis of polymerization process and polymer properties, synthesis of polymers with controlled microstructures by coordination polymerization using metal complexes, synthesis of polymer with controlled microstructures by precision polycondensation, molecular recognition in catalyst-reaction site, and synthesis of imprinting polymers. 246 refs., 117 figs., 14 tabs.

Efficacy of CTA portography for preoperatively determining the segmental location of focal hepatic lesions

International Nuclear Information System (INIS)

Nelson, R.C.; Chemzmar, J.L.; Sugarbaker, P.H.; Bernardino, M.E.

1989-01-01

Using cross-sectional images to localize tumors to specific hepatic segments before resection might be difficult because the transverse scissura, an important segmental landmark, is approximately parallel to the axial plane. Since this plane is parallel to the main right and left portal pedicles, the authors postulated that they could localize lesions above this plane to segments 2,4A,7, or 8, and below this plane to segments 3, 4B,5, or 6. The authors have retrospectively evaluated, in a blinded fashion, 24 hepatic masses in 13 patients who underwent CTA-portography and subsequent tumor resection. Using this scheme, they have accurately predicted the primary segmental location in 22 (92%) of 24 surgically confirmed lesions

Synthesis of magnetic polymeric microspheres

Energy Technology Data Exchange (ETDEWEB)

Gervald, A Yu; Gritskova, Inessa A; Prokopov, Nikolai I [M.V. Lomonosov Moscow State Academy of Fine Chemical Technology, Moscow (Russian Federation)

2010-05-13

The key types of magnetic polymeric microspheres are considered. Methods of synthesis of different types of magnetic nanoparticles and of preparation of stable magnetic fluids on their basis are outlined. The overview of the methods for the manufacture of magnetic polymeric microspheres is presented. The effect of the synthesis conditions on the characteristics of magnetic polymeric microspheres such as the diameter and the particle size distribution and the content of magnetic material is discussed by particular examples. The application fields of magnetic polymeric microspheres are briefly surveyed.

Synthesis of magnetic polymeric microspheres

International Nuclear Information System (INIS)

Gervald, A Yu; Gritskova, Inessa A; Prokopov, Nikolai I

2010-01-01

The key types of magnetic polymeric microspheres are considered. Methods of synthesis of different types of magnetic nanoparticles and of preparation of stable magnetic fluids on their basis are outlined. The overview of the methods for the manufacture of magnetic polymeric microspheres is presented. The effect of the synthesis conditions on the characteristics of magnetic polymeric microspheres such as the diameter and the particle size distribution and the content of magnetic material is discussed by particular examples. The application fields of magnetic polymeric microspheres are briefly surveyed.

Removal of phenol from aqueous solution using polymer inclusion membrane based on mixture of CTA and CA

Science.gov (United States)

Benosmane, Nadjib; Boutemeur, Baya; Hamdi, Safouane M.; Hamdi, Maamar

2018-03-01

Nowadays, there are increasingly stringent regulations requiring more and more treatment of industrial effluents to generate product waters which could be easily reused or disposed of to the environment without any harmful effects. In the present work, the removal of phenol from aqueous solution across polymer inclusion membrane (PIM), based on mixture of cellulose triacetate and cellulose acetate as support (75/25%), calix[4]resorcinarene derivative as a carrier and 2-nitrophenyl octyl ether (2-NPOE) as plasticizer was investigated. The experimental part of this investigation involved the influence of carrier nature, plasticizer concentration, pH phases, and phenol initial concentration on the removal efficiency of phenol from synthetic wastewater. A PIM containing 0.1 g (of mixture polymer), (0.15 g/g mixture of polymer) of carrier and (0.03 ml/g mixture of polymer) of 2-NPOE provided the highest percentage of phenol removal efficiency over a 6-day transport; the removal was found to be about 95%, indeed the removal was found to be highly dependent of pH phases. The feed solution in these transport experiments was at pH 2, while the stripping solution contained 0.20 M NaOH. This study claims that the PIM with a mixture of cellulose derivatives can be used effectively to remove phenols from wastewaters.

NATO Advanced Study Institute on Ring-opening Metathesis Polymerization of Olefins and Polymerization of Alkynes

CERN Document Server

1998-01-01

The first NATO Advanced Study Institute on Olefin Metathesis and Polymerization Catalysts was held on September 10-22, 1989 in Akcay, Turkey. Based on the fundamental research of RRSchrock, RGrubbs and K.B.Wagener in the field of ring opening metathesis polymerization (ROMP), acyclic diene metathesis (ADMET) and alkyne polymerization, these areas gained growing interest within the last years. Therefore the second NATO-ASI held on metathesis reactions was on Ring Opening Metathesis Po­ lymerization of Olefins and Polymerization of Alkynes on September 3-16, 1995 in Akcay, Turkey. The course joined inorganic, organic and polymer chemists to exchange their knowledge in this field. This volume contains the main and short lectures held in Akcay. To include ADMET reactions better into the title of this volume we changed it into: Metathesis Polymerization of Olefins and Alkyne Polymerization. This volume is addressed to research scientists, but also to those who start to work in the area of olefin metathesis and al...

RAFT polymerization mediated bioconjugation strategies

OpenAIRE

Bulmuş, Volga

2011-01-01

This review aims to highlight the use of RAFT polymerization in the synthesis of polymer bioconjugates. It covers two main bioconjugation strategies using the RAFT process: (i) post-polymerization bioconjugations using pre-synthesized reactive polymers, and (ii) bioconjugations via in situ polymerization using biomolecule-modified monomers or chain transfer agents. © 2011 The Royal Society of Chemistry.

Use of hydroxypropyl-beta-cyclodextrin ad polymer matrix for formation of inclusion complex with drug nifedipine

International Nuclear Information System (INIS)

Carneiro, Elisa F.; Araujo, Marcia V.G. de; Barbosa, Ronilson V.; Silva, Caroline W.P. da; Barisson, Andersson; Zawadzki, Sonia F.; Andrade, George Ricardo S.; Costa Junior, Nivan B. da

2009-01-01

In this work it was prepared and characterized an inclusion complex between the polymeric matrix hydroxypropyl-beta cyclodextrin and nifedipine, a hydrophobic drug calcium antagonistic, used for the cardiovascular diseases treatment. The study of the phase- solubility diagram showed an increase of the aqueous solubility of the drug after inclusion, was observed and The differential scanning calorimetry analysis did not show the melting point temperature of the drug in the formed complex. This fact is considered as an evidence of the encapsulation process. 1 H NMR studies suggested that the non-aromatic ring of the nifedipine would be inserted in the cavity of the hydroxypropyl-beta-cyclodextrin.This orientation was also proposed by the used molecular modelling methods. (author)

Packaging based on polymeric materials

Directory of Open Access Journals (Sweden)

Jovanović Slobodan M.

2005-01-01

Full Text Available In the past two years the consumption of common in the developed countries world wide (high tonnage polymers for packaging has approached a value of 50 wt.%. In the same period more than 50% of the packaging units on the world market were made of polymeric materials despite the fact that polymeric materials present 17 wt.% of all packaging materials. The basic properties of polymeric materials and their environmental and economical advantages, providing them such a position among packaging materials, are presented in this article. Recycling methods, as well as the development trends of polymeric packaging materials are also presented.

Fatty degeneration of the rotator cuff muscles on pre- and postoperative CT arthrography (CTA): is the Goutallier grading system reliable?

Energy Technology Data Exchange (ETDEWEB)

Lee, Eugene; Choi, Jung-Ah; Kang, Heung Sik [Seoul National University Bundang Hospital, Department of Radiology, Seongnam-si, Gyeongi-do (Korea, Republic of); Seoul National University College of Medicine, Department of Radiology, 28 Yeongon-dong, Chongno-gu, Seoul (Korea, Republic of); Oh, Joo Han [Seoul National University Bundang Hospital, Department of Orthopedic Surgery, Seongnam-si, Gyeongi-do (Korea, Republic of); Ahn, Soyeon [Seoul National University Bundang Hospital, Medical Research Collaborating Center, Seongnam-si, Gyeongi-do (Korea, Republic of); Hong, Sung Hwan [Seoul National University College of Medicine, Department of Radiology, 28 Yeongon-dong, Chongno-gu, Seoul (Korea, Republic of); Chai, Jee Won [SMG-SNU Boramae Medical Center, Department of Radiology, 425 Shindaebang-dong, Dongjak-gu, Seoul (Korea, Republic of)

2013-09-15

To retrospectively evaluate fatty degeneration (FD) of rotator cuff muscles on CTA using Goutallier's grading system and quantitative measurements with comparison between pre- and postoperative states. IRB approval was obtained for this study. Two radiologists independently reviewed pre- and postoperative CTAs of 43 patients (24 males and 19 females, mean age, 58.1 years) with 46 shoulders confirmed as full-thickness tears with random distribution. FD of supraspinatus, infraspinatus/teres minor, and subscapularis was assessed using Goutallier's system and by quantitative measurements of Hounsfield units (HUs) on sagittal images. Changes in FD grades and HUs were compared between pre- and postoperative CTAs and analyzed with respect to preoperative tear size and postoperative cuff integrity. The correlations between qualitative grades and quantitative measurements and their inter-observer reliabilities were also assessed. There was statistically significant correlation between FD grades and HU measurements of all muscles on pre- and postoperative CTA (p < 0.05). Inter-observer reliability of fatty degeneration grades were excellent to substantial on both pre- and postoperative CTA in supraspinatus (0.8685 and 0.8535) and subscapularis muscles (0.7777 and 0.7972), but fair in infraspinatus/teres minor muscles (0.5791 and 0.5740); however, quantitative Hounsfield units measurements showed excellent reliability for all muscles (ICC: 0.7950 and 0.9346 for SST, 0.7922 and 0.8492 for SSC, and 0.9254 and 0.9052 for IST/TM). No muscle showed improvement of fatty degeneration after surgical repair on qualitative and quantitative assessments; there was no difference in changes of fatty degeneration after surgical repair according to preoperative tear size and post-operative cuff integrity (p > 0.05). The average dose-length product (DLP, mGy . cm) was 365.2 mGy . cm (range, 323.8-417.2 mGy . cm) and estimated average effective dose was 5.1 mSv. Goutallier grades

CTA-A project for a new generation of Cherenkov telescopes

International Nuclear Information System (INIS)

Doro, Michele

2011-01-01

Gamma-rays provide a powerful insight into the non-thermal universe and perhaps a unique probe for new physics beyond the standard model. Current experiments are already giving results in the physics of acceleration of cosmic rays in supernova remnants, pulsar and active galactic nuclei with a 100 sources detected at very-high-energies so far. Despite its relatively recent appearance, very high-energy gamma-ray astronomy has proven to have reached a mature technology with fast assembling, relatively cheap and reliable telescopes. The goal of future installation is to increase the sensitivity by a factor 10 compared to current installations, and enlarge the energy domain from few 10s of GeV to a 100 TeV. Gamma-ray spectra of astrophysical origin are rather soft thus hardly one single size telescope can cover more than 1.5 decades in energy, therefore an array of telescopes of 2-3 different sizes is required. Hereafter, we present design considerations for a Cherenkov Telescope Array (CTA), a project for a new generation of highly automated telescopes for gamma-ray astronomy. The status of the project, technical solutions and an insight in the involved physics will be presented.

A Novel Approach to Reinstating Tolerance in Experimental Autoimmune Myasthenia Gravis Using a Targeted Fusion Protein, mCTA1–T146

Directory of Open Access Journals (Sweden)

Alessandra Consonni

2017-09-01

Full Text Available Reinstating tissue-specific tolerance has attracted much attention as a means to treat autoimmune diseases. However, despite promising results in rodent models of autoimmune diseases, no established tolerogenic therapy is clinically available yet. In the experimental autoimmune myasthenia gravis (EAMG model several protocols have been reported that induce tolerance against the prime disease-associated antigen, the acetylcholine receptor (AChR at the neuromuscular junction. Using the whole AChR, the extracellular part or peptides derived from the receptor, investigators have reported variable success with their treatments, though, usually relatively large amounts of antigen has been required. Hence, there is a need for better formulations and strategies to improve on the efficacy of the tolerance-inducing therapies. Here, we report on a novel targeted fusion protein carrying the immunodominant peptide from AChR, mCTA1–T146, which given intranasally in repeated microgram doses strongly suppressed induction as well as ongoing EAMG disease in mice. The results corroborate our previous findings, using the same fusion protein approach, in the collagen-induced arthritis model showing dramatic suppressive effects on Th1 and Th17 autoaggressive CD4 T cells and upregulated regulatory T cell activities with enhanced IL10 production. A suppressive gene signature with upregulated expression of mRNA for TGFβ, IL10, IL27, and Foxp3 was clearly detectable in lymph node and spleen following intranasal treatment with mCTA1–T146. Amelioration of EAMG disease was accompanied by reduced loss of muscle AChR and lower levels of anti-AChR serum antibodies. We believe this targeted highly effective fusion protein mCTA1–T146 is a promising candidate for clinical evaluation in myasthenia gravis patients.

Chelating polymeric membranes

KAUST Repository

Peinemann, Klaus-Viktor

2015-01-22

The present application offers a solution to the current problems associated with recovery and recycling of precious metals from scrap material, discard articles, and other items comprising one or more precious metals. The solution is premised on a microporous chelating polymeric membrane. Embodiments include, but are not limited to, microporous chelating polymeric membranes, device comprising the membranes, and methods of using and making the same.

Functionalization and Polymerization on the CNT Surfaces

KAUST Repository

Albuerne, Julio

2013-07-01

In this review we focus on the current status of using carbon nanotube (CNT) as a filler for polymer nanocomposites. Starting with the historical background of CNT, its distinct properties and the surface functionalization of the nanotube, the three different surface polymerization techniques, namely grafting "from", "to" and "through/in between" were discussed. Wider focus has been given on "grafting from" surface initiated polymerizations, including atom transfer radical polymerization (ATRP), reversible addition fragmentation chain-transfer (RAFT) Polymerization, nitroxide mediated polymerization (NMP), ring opening polymerization (ROP) and other miscellaneous polymerization methods. The grafting "to" and "through / in between" also discussed and compared with grafting from polymerization. The merits and shortcomings of all three grafting methods were discussed and the bottleneck issue in grafting from method has been highlighted. Furthermore the current and potential future industrial applications were deliberated. Finally the toxicity issue of CNTs in the final product has been reviewed with the limited available literature knowledge. © 2013 Bentham Science Publishers.

X-RAY PULSATIONS FROM THE RADIO-QUIET GAMMA-RAY PULSAR IN CTA 1

International Nuclear Information System (INIS)

Caraveo, P. A.; De Luca, A.; Marelli, M.; Bignami, G. F.; Ray, P. S.; Saz Parkinson, P. M.; Kanbach, G.

2010-01-01

Prompted by the Fermi-LAT discovery of a radio-quiet gamma-ray pulsar inside the CTA 1 supernova remnant, we obtained a 130 ks XMM-Newton observation to assess the timing behavior of this pulsar. Exploiting both the unprecedented photon harvest and the contemporary Fermi-LAT timing measurements, a 4.7σ single-peak pulsation is detected, making PSR J0007+7303 the second example, after Geminga, of a radio-quiet gamma-ray pulsar also seen to pulsate in X-rays. Phase-resolved spectroscopy shows that the off-pulse portion of the light curve is dominated by a power-law, non-thermal spectrum, while the X-ray peak emission appears to be mainly of thermal origin, probably from a polar cap heated by magnetospheric return currents, pointing to a hot spot varying throughout the pulsar rotation.

Nanoporous Polymeric Grating-Based Biosensors

KAUST Repository

Gao, Tieyu; Hsiao, Vincent; Zheng, Yue Bing; Huang, Tony Jun

2012-01-01

We demonstrate the utilization of an interferometrically created nanoporous polymeric gratings as a platform for biosensing applications. Aminopropyltriethoxysilane (APTES)-functionalized nanoporous polymeric gratings was fabricated by combining holographic interference patterning and APTES-functionalization of pre-polymer syrup. The successful detection of multiple biomolecules indicates that the biofunctionalized nanoporous polymeric gratings can act as biosensing platforms which are label-free, inexpensive, and applicable as high-throughput assays. Copyright © 2010 by ASME.

Nanoporous Polymeric Grating-Based Biosensors

KAUST Repository

Gao, Tieyu

2012-05-02

We demonstrate the utilization of an interferometrically created nanoporous polymeric gratings as a platform for biosensing applications. Aminopropyltriethoxysilane (APTES)-functionalized nanoporous polymeric gratings was fabricated by combining holographic interference patterning and APTES-functionalization of pre-polymer syrup. The successful detection of multiple biomolecules indicates that the biofunctionalized nanoporous polymeric gratings can act as biosensing platforms which are label-free, inexpensive, and applicable as high-throughput assays. Copyright © 2010 by ASME.

CTA/V detection of bilateral sigmoid sinus dehiscence and suspected idiopathic intracranial hypertension in unilateral pulsatile tinnitus

International Nuclear Information System (INIS)

Xu, Shuaishuai; Xu, Jianrong; Ruan, Shidong; Liu, Shanfeng; Gong, Ruozhen

2018-01-01

This aimed to evaluate the prevalence and extent of bilateral sigmoid sinus dehiscence (SSD) and to explore the presence of idiopathic intracranial hypertension (IIH) in patients with unilateral pulsatile tinnitus (PT) with CTA/V. Sixty PT patients (52 females; 40.4 ± 11.6 years [20-72]) who underwent CTA/V and 30 non-PT patients (27 females; 38.4 ± 14.7 years [12-62]) were enrolled in this study. The primary outcome measure was the radiographic presence of SSD. The index of transverse sinus stenosis (ITSS) was obtained by multiplying the stenosis scale values for each transverse sinus, and once was ≥ 4, the presence of IIH was suspected. The prevalence and extent of SSD on symptomatic side (78%; maximum transverse diameter, MTD 0.49 ± 0.23; maximum vertical diameter, MVD 0.50 ± 0.26 cm) were significantly higher and larger than those on asymptomatic side (50%, P < 0.001; MTD 0.35 ± 0.18, P = 0.006; MVD 0.30 ± 0.15 cm, P < 0.001) in the study group and those (20%, P < 0.001; MTD 0.36 ± 0.18, P = 0.073; MVD 0.30 ± 0.22 cm, P < 0.048) in the control group. The presence of SSD showed significant correlation with both PT (logistic regression analysis, OR 4.167 [1.450-11.97]; P = 0.008) and suspected IIH (OR 16.25 [1.893-139.5]; P = 0.011). In PT patients, SSD has a significant correlation with PT and a potential correlation with IIH. (orig.)

KINETICS OF SUSPENDED EMULSION POLYMERIZATION OF METHYL METHACRYLATE

Institute of Scientific and Technical Information of China (English)

Yong-zhong Bao; Cheng-xi Wang; Zhi-ming Huang; Zhi-xue Weng

2004-01-01

The kinetics of suspended emulsion polymerization of methyl methacrylate (MMA), in which water acted as the dispersed phase and the mixture of MMA and cyclohexane as the continuous phase, was investigated. It showed that the initial polymerization rate (Rp0) and steady-state polymerization rate (Rp) were proportional to the mass ratio between water and oil phase, and increased as the polymerization temperature, the potassium persulphate concentration ([I]) and the Tween20 emulsifier concentration ([S]) increased. The relationships between the polymerization rate and [I] and [S] were obtained as follows: Rp0 ∝ [I]0.73[S]0.32 and Rp ∝ [I]0.71[S]0.23. The above exponents were close to those obtained from normal MMA emulsion polymerization. It also showed that the average molecular weight of the resulting poly(methyl methacrylate) decreased as the polymerization temperature, [I] and [S] increased. Thus, MMA suspended emulsion polymerization could be considered as a combination of many miniature emulsion polymerizations proceeding in water drops and obeyed the classical kinetics of MMA emulsion polymerization.

SYNTHESIS OF BLOCK COPOLYMER BY INTEGRATED LIVING ANIONIC POLYMERIZATION-ATOM TRANSFER RADICAL POLYMERIZATION (ATRP)

Institute of Scientific and Technical Information of China (English)

Bing Liu; Feng Liu; Ning Luo; Sheng-kang Ying; Qing Liu

2000-01-01

Alpha-trichloroacetoxy terminated polystyrene oligomer (PS-CH2CH2OCOCCl3) and poly-(styrene-b-butadiene)oligomer [P(S-b-B)-CH2CH2OCOCCl3)] were synthesized by living anionic polymeri-zation using n-butyllithium as initiator.Then the PS-CH2CH2OCOCCl3 (PS-Cl3) or P(S-b-B)-CH2CH2O-COCCl3 (PSB-Cl3) was used as the macroinitiator in the polymerization of (meth)acrylates in the presence of CuX/bpy. AB diblock and ABC triblock copolymers were prepared by the integrated living anionic polymerization (LAP)-atom transfer radical polymerization (ATRP). The structures of the PSB-Cl3 and the P(S-b-MMA) were identified by FTIR and 1H-NMR spectrum, respectively. A new way to design block copolymers (the combination of LAP and ATRP) was developed.

Inflation of a Polymeric Menbrane

DEFF Research Database (Denmark)

Kristensen, Susanne B.; Larsen, Johannes R.; Hassager, Ole

1998-01-01

We consider an axisymmetric polymeric membrane inflated by a uniform pressure difference acting across the membrane.......We consider an axisymmetric polymeric membrane inflated by a uniform pressure difference acting across the membrane....

Social inclusion and inclusive education

Directory of Open Access Journals (Sweden)

Marsela Robo

2014-07-01

In line with global debate on social inclusion and exclusion, the author brings the way this debate has now pervaded both the official and development policy discourse in Albania.Social inclusion is considered as one of the priorities of the current government, with poverty reduction as its main focus, which will be ensured not only through economic development. In the end, the article focuses on the role of education as a very important and useful tool for ensuring social inclusion.Social inclusion through education, in particular through vocational education, considered by the author as the only way towards sustainable development of Albanian society.

Polymeric membrane materials for artificial organs.

Science.gov (United States)

Kawakami, Hiroyoshi

2008-01-01

Many polymeric materials have already been used in the field of artificial organs. However, the materials used in artificial organs are not necessarily created with the best material selectivity and materials design; therefore, the development of synthesized polymeric membrane materials for artificial organs based on well-defined designs is required. The approaches to the development of biocompatible polymeric materials fall into three categories: (1) control of physicochemical characteristics on material surfaces, (2) modification of material surfaces using biomolecules, and (3) construction of biomimetic membrane surfaces. This review will describe current issues regarding polymeric membrane materials for use in artificial organs.

High Vacuum Techniques for Anionic Polymerization

KAUST Repository

Ratkanthwar, Kedar

2015-09-01

Anionic polymerization high vacuum techniques (HVTs) are the most suitable for the preparation of polymer samples with well-defined complex macromolecular architectures. Though HVTs require glassblowing skill for designing and making polymerization reactor, it is the best way to avoid any termination of living polymers during the number of steps for the synthesis of polymers with complex structure. In this chapter, we describe the different polymerization reactors and HVTs for the purification of monomers, solvents, and other reagents for anionic polymerization as well as few model reactions for the synthesis of polymers with simple to complex structure.

THE EFFECTS OF N-2-HYDROXYETHYL-N-METHYL-P-TOLUIDINE ON METHYL METHACRYLATE RADICAL POLYMERIZATION AND ACRYLONITRILE PHOTOINDUCED POLYMERIZATION

Institute of Scientific and Technical Information of China (English)

QIU Kunyuan; ZHANG Zhanghua; FENG Xinde

1992-01-01

The effects of N-2-hydroxyethyl-N-methyl-p-toluidine (HMT) on MMA polymerization using organic peroxide as an initiator and on AN photoinduced polymerization have been investigated respectively. The kinetics of polymerization and the overall activation energy of polymerization were determined. Based on kinetics study and the end group analysis of the polymer obtained by UV spectrum method, the initiation mechanism is proposed.

Characterization behavior of some polymeric composite ion exchangers

International Nuclear Information System (INIS)

El-Zahhar, A.A; Ahdel-Aziz, H.M.; Siyam, T.

2005-01-01

Polymeric composite resins were prepared by template polymerization process in aqueous solution. Thermogravimetric analysis (TGA), differential thermal analysis (DTA) and The X-ray diffraction patterns (XRD) were performed to evaluate the physico chemical properties of the different polymeric composite resins. The TGA and DTA clarify high thermal stability of prepared polymeric composite resins. XRD of prepared polymeric composite shows that there is crystalline structure of some resins while other are amorphous one

Nanoparticles from a controlled polymerization process

International Nuclear Information System (INIS)

Tirumala, V.R.; Caneba, G.T.; Dar, Y.; Wang, H.-H.; Mancini, D.C.

2003-01-01

Free-radical retrograde precipitation polymerization process in the past has shown excellent control characteristics over reaction rate, molecular weight, and in the entrapment of live radicals for the generation of block copolymers. The same principle has now been extended to study the reaction confinement to a nanoscale region. Nanosized polymer particles have been reported to form from block copolymers, conventional precipitation polymerization methods, or through emulsion polymerization approaches. In this work, we present a new method of generating nanosized polymer particles by polymerizing the monomer in an environment that precipitates the polymer above the lower critical solution temperature. The nanoparticles have been characterized by both tapping-mode atomic force microscopy observations and in situ synchrotron time-resolved small-angle X-ray scattering analysis. The results from both the techniques showed the formation of nanoparticles in the size range of 15-30 nm, directly from the polymerization process.

Fatty degeneration of the rotator cuff muscles on pre- and postoperative CT arthrography (CTA): is the Goutallier grading system reliable?

International Nuclear Information System (INIS)

Lee, Eugene; Choi, Jung-Ah; Kang, Heung Sik; Oh, Joo Han; Ahn, Soyeon; Hong, Sung Hwan; Chai, Jee Won

2013-01-01

To retrospectively evaluate fatty degeneration (FD) of rotator cuff muscles on CTA using Goutallier's grading system and quantitative measurements with comparison between pre- and postoperative states. IRB approval was obtained for this study. Two radiologists independently reviewed pre- and postoperative CTAs of 43 patients (24 males and 19 females, mean age, 58.1 years) with 46 shoulders confirmed as full-thickness tears with random distribution. FD of supraspinatus, infraspinatus/teres minor, and subscapularis was assessed using Goutallier's system and by quantitative measurements of Hounsfield units (HUs) on sagittal images. Changes in FD grades and HUs were compared between pre- and postoperative CTAs and analyzed with respect to preoperative tear size and postoperative cuff integrity. The correlations between qualitative grades and quantitative measurements and their inter-observer reliabilities were also assessed. There was statistically significant correlation between FD grades and HU measurements of all muscles on pre- and postoperative CTA (p 0.05). The average dose-length product (DLP, mGy . cm) was 365.2 mGy . cm (range, 323.8-417.2 mGy . cm) and estimated average effective dose was 5.1 mSv. Goutallier grades correlated well with HUs of rotator cuff muscles. Reliability was excellent for both systems, except for FD grade of IST/TM muscles, which may be more reliably assessed using quantitative measurements. (orig.)

The front-end electronics and slow control of large area SiPM for the SST-1M camera developed for the CTA experiment

Czech Academy of Sciences Publication Activity Database

Aguilar, J.A.; Bilnik, W.; Borkowski, J.; Mandát, Dušan; Pech, Miroslav; Schovánek, Petr

Roč. 830, Sep (2016), s. 219-232 ISSN 0168-9002 R&D Projects: GA MŠk LM2015046; GA MŠk LE13012; GA MŠk LG14019 Institutional support: RVO:68378271 Keywords : CTA * SiPM * G-APD * preamplifier * front-end * slow-control * compensation Subject RIV: BF - Elementary Particles and High Energy Physics Impact factor: 1.362, year: 2016

Peptide block copolymers by N-carboxyanhydride ring-opening polymerization and atom transfer radical polymerization: The effect of amide macroinitiators

NARCIS (Netherlands)

Habraken, G.J.M.; Koning, C.E.; Heise, A.

2009-01-01

The synthesis of polypeptide-containing block copolymers combining N-carboxyanhydride (NCA) ring-opening polymerization and atom transfer radical polymerization (ATRP) was investigated. An amide initiator comprising an amine function for the NCA polymerization and an activated bromide for ATRP was

Synthesis and polymerization of vinyl triazolium ionic liquids

Science.gov (United States)

Luebke, David; Nulwala, Hunaid; Matyjaszewski, Krzysztof; Adzima, Brian

2018-05-15

Herein, we describe polymerized ionic liquids, demonstrate the synthesis of polymerized ionic liquids, and demonstrate the polymerization of triazolium monomers. One embodiment shows the polymeriazation of the triazolium monomers with bis(trifluoromethanesulfonyl)imide anions. In another embodiment we show the feasibility of copolymerizing with commodity monomers such as styrene using free radical polymerization techniques.

Experimental study of living free radical polymerization using trifunctional initiator and polymerization mediated by nitroxide

International Nuclear Information System (INIS)

Galhardo, Eduardo; Lona, Liliane M.F.

2009-01-01

Controlled free radical polymerization or living free radical polymerization has received increasing attention as a technique for the production of polymers with microstructure highly controlled. In particular, narrow molecular weight distributions are obtained with polydispersity very close to one. In this research it was investigate the controlled polymerization mediated by nitroxide, using a cyclic trifunctional peroxide. As long as we know, there are only publications in literature dealing with NMRP using mono- and bi-functional initiators. It was believed that the trifunctional peroxide can increase the rate of polymerization, since more free radicals are generated, if compared with initiators with lower functionality. Furthermore, the fact of the initiator be cyclic means that branches are not generated in the chains, which theoretically prevents an increase in polydispersity of the polymer. The effect of the dissociation constant of the trifunctional initiator in the velocity of the reaction was analyzed. (author)

Atherosclerotic plaque component segmentation in combined carotid MRI and CTA data incorporating class label uncertainty

DEFF Research Database (Denmark)

van Engelen, Arna; Niessen, Wiro J.; Klein, Stefan

2014-01-01

Atherosclerotic plaque composition can indicate plaque vulnerability. We segment atherosclerotic plaque components from the carotid artery on a combination of in vivo MRI and CT-angiography (CTA) data using supervised voxelwise classification. In contrast to previous studies the ground truth...... for training is directly obtained from 3D registration with histology for fibrous and lipid-rich necrotic tissue, and with [Formula: see text]CT for calcification. This registration does, however, not provide accurate voxelwise correspondence. We therefore evaluate three approaches that incorporate uncertainty......), II) samples are weighted by the local contour distance of the lumen and outer wall between histology and in vivo data, and III) 10% of each class is rejected by Gaussian outlier rejection. Classification was evaluated on the relative volumes (% of tissue type in the vessel wall) for calcified...

Preparations of spherical polymeric particles from Tanzanian ...

African Journals Online (AJOL)

Spherical Polymeric Particles (SPP) have been prepared from Tanzanian Cashew Nut Shell Liquid (CNSL) by suspension polymerization technique involving either step-growth or chain- growth polymerization mechanisms. The sizes of the SPP, which ranged from 0.1 to 2.0 mm were strongly influenced by the amounts of ...

Volumetric polymerization shrinkage of contemporary composite resins

Directory of Open Access Journals (Sweden)

Halim Nagem Filho

2007-10-01

Full Text Available The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill Magic, Alert, and Solitaire to determine whether there are differences among these materials. The tests were conducted with precision of 0.1 mg. The volumetric shrinkage was measured by hydrostatic weighing before and after polymerization and calculated by known mathematical equations. One-way ANOVA (a or = 0.05 was used to determine statistically significant differences in volumetric shrinkage among the tested composite resins. Suprafill (1.87±0.01 and Definite (1.89±0.01 shrank significantly less than the other composite resins. SureFil (2.01±0.06, Filtek Z250 (1.99±0.03, and Fill Magic (2.02±0.02 presented intermediate levels of polymerization shrinkage. Alert and Solitaire presented the highest degree of polymerization shrinkage. Knowing the polymerization shrinkage rates of the commercially available composite resins, the dentist would be able to choose between using composite resins with lower polymerization shrinkage rates or adopting technical or operational procedures to minimize the adverse effects deriving from resin contraction during light-activation.

Radiation-induced graft polymerization of amphiphilic monomers with different polymerization characteristics onto hydrophobic polysilane

Energy Technology Data Exchange (ETDEWEB)

Tanaka, Hidenori; Iwasaki, Isao; Kunai, Yuichiro [Research Reactor Institute, Kyoto University, Asashironishi 2-1010, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan); Sato, Nobuhiro, E-mail: sato-n@rri.kyoto-u.ac.j [Research Reactor Institute, Kyoto University, Asashironishi 2-1010, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan); Matsuyama, Tomochika [Research Reactor Institute, Kyoto University, Asashironishi 2-1010, Kumatori-cho, Sennan-gun, Osaka 590-0494 (Japan)

2011-08-15

The structures of poly(methyl-n-propylsilane) (PMPrS) amphiphilically modified through {gamma}-ray-induced graft polymerization were investigated with {sup 1}H NMR measurement. By the use of methyl methacrylate (MMA) or diethyl fumarate (DEF) as monomers for the graft polymerization, grafting yield rose with increasing total absorption dose and monomer concentrations, but decreased with increasing dose rate. This result means that grafting yield of modified PMPrS can be controlled by changing irradiation conditions. However, the number of PMMA or PDEF graft chains per PMPrS chain was estimated to be less than 1.0 by analysis of {sup 1}H NMR spectra, and this value was lower than that we had expected. To improve graft density, maleic anhydride (MAH), which is known as a non-homopolymerizable monomer in radical polymerization, was used as a monomer for grafting. As a result, high density grafting (one MAH unit for 4.2 silicon atoms) was attained. It demonstrates that the structure of {gamma}-ray-modified polysilane strongly depends on the polymerization characteristics of grafted monomers.

Radiation-induced polymerization and radiation effect on polymers

International Nuclear Information System (INIS)

Seguchi, Tadao

1977-12-01

The processes of radiation-induced polymerization of monomers and also radiation effects on polymers have been studied by instrumental analyses of electron spin resonance (ESR), nuclear magnetic resonance (NMR) and electron microscopy. In radiation-induced polymerization, graft-copolymerization and absorbed state polymerization were taken up. For graft-copolymerization, monomers such as methylmethacrylate and butadiene were made to react with irradiated polyethylene, and behaviors of the initiating radicals and propagating radicals were followed under the reaction by ESR. For absorbed state polymerization, acrylonitrile/zeolite and methylmethacrylate/zeolite were chosen. Absorbed monomers were irradiated at 77 0 K and polymerized at room temperature. Active species and the concentrations were measured by ESR and the yields of polymer were observed by NMR. In radiation effect on polymers, polyvinylfluoride, polyvinylidenfluoride and polytetrafluoroethylene were taken up. Active species trapped in the polymer matrixes were identified and decay and reactivity of the species were also studied. On the basis of information from the electron microscopy and x-ray analysis, radiation effects on these polymers are described. In polytetrafluoroethylene produced by radiation polymerization, the relation between morphology and polymerization conditions and also the process of crystallization during polymerization were studied. (auth.)

Polymerization of N-(fluoro phenyl) maleimides

International Nuclear Information System (INIS)

Barrales-Rienda, J.M.; Ramos, J.G.; Chaves, M.S.

1979-01-01

Poly(N-aryl maleimide)s of characteristic structures have been synthesized and some of their physical properties studied. The polymerization of N-(fluoro phenyl) maleimides by free-radical initiation in bulk or in solution and by anionic catalyst have been studied to compare the characteristics of polymerization by γ-ray irradiation with that by free-radical initiation. The polymers were characterized by elemental analysis, intrinsic viscosity, spectroscopy (IR and NMR), programmed thermogravimetric analysis, and x-ray diffraction. Spectra of polymers prepared by radiation and anionic polymerization were nearly identical with those of polymers prepared by free-radical polymerization initiated by azobisisobutyronitrile in bulk or in solution and by the self-initiated thermal polymerization. A variety of reaction conditions were tried, but all attempts to change the molecular structure of the polymers were unsuccessful. Rates of thermal degradation for poly[N-(fluoro phenyl) maleimide]s have been analyzed by using a multiple-heating-rate procedure. Overall activation energy, order of reaction, and frequency factor have been evaluated. 6 figures, 8 tables

Plasma polymerization by Softplasma

DEFF Research Database (Denmark)

Jiang, J.; Wu, Zhenning; Benter, Maike

2008-01-01

, external electrode, and electrodeless microwave or high frequency reactors. [3] Softplasma™ is an internal electrode plasma setup powered by low frequenc~ gower supply. It was developed in late 90s for surface treatment of silicone rubber. [ ]- 5] It is a low pressure, low electron density, 3D homogenous......In the late 19th century, the first depositions - known today as plasma polymers, were reported. In the last century, more and more research has been put into plasma polymers. Many different deposition systems have been developed. [1, 2] Shi F. F. broadly classified them into internal electrode...... plasma. In this study, we are presenting the surface modification"pf polymers by plasma polymerization using Softplasma™. Softplasma™ can be used for two major types of polymerization: polymerization of vinyl monomers, where plasma acts as initiator; chemical vapour deposition, where plasma acts...

High Vacuum Techniques for Anionic Polymerization

KAUST Repository

Ratkanthwar, Kedar; Hadjichristidis, Nikolaos; Mays, Jimmy

2015-01-01

Anionic polymerization high vacuum techniques (HVTs) are the most suitable for the preparation of polymer samples with well-defined complex macromolecular architectures. Though HVTs require glassblowing skill for designing and making polymerization

Antibiotic polymeric nanoparticles for biofilm-associated infection therapy.

Science.gov (United States)

Cheow, Wean Sin; Hadinoto, Kunn

2014-01-01

Polymeric nanoparticles are highly attractive as drug delivery vehicles due to their high structural integrity, stability during storage, ease of preparation and functionalization, and controlled release capability. Similarly, lipid-polymer hybrid nanoparticles, which retain the benefits of polymeric nanoparticles plus the enhanced biocompatibility and prolonged circulation time owed to the lipids, have recently emerged as a superior alternative to polymeric nanoparticles. Drug nanoparticle complex prepared by electrostatic interaction of oppositely charged drug and polyelectrolytes represents another type of polymeric nanoparticle. This chapter details the preparation, characterization, and antibiofilm efficacy testing of antibiotic-loaded polymeric and hybrid nanoparticles and antibiotic nanoparticle complex.

Measurement and Analysis of in vitro Actin Polymerization

Science.gov (United States)

Doolittle, Lynda K.; Rosen, Michael K.; Padrick, Shae B.

2014-01-01

Summary The polymerization of actin underlies force generation in numerous cellular processes. While actin polymerization can occur spontaneously, cells maintain control over this important process by preventing actin filament nucleation and then allowing stimulated polymerization and elongation by several regulated factors. Actin polymerization, regulated nucleation and controlled elongation activities can be reconstituted in vitro, and used to probe the signaling cascades cells use to control when and where actin polymerization occurs. Introducing a pyrene fluorophore allows detection of filament formation by an increase in pyrene fluorescence. This method has been used for many years and continues to be broadly used, owing to its simplicity and flexibility. Here we describe how to perform and analyze these in vitro actin polymerization assays, with an emphasis on extracting useful descriptive parameters from kinetic data. PMID:23868594

A Comparison of the Updated Diamond-Forrester, CAD Consortium, and CONFIRM History-Based Risk Scores for Predicting Obstructive Coronary Artery Disease in Patients With Stable Chest Pain: The SCOT-HEART Coronary CTA Cohort.

Science.gov (United States)

Baskaran, Lohendran; Danad, Ibrahim; Gransar, Heidi; Ó Hartaigh, Bríain; Schulman-Marcus, Joshua; Lin, Fay Y; Peña, Jessica M; Hunter, Amanda; Newby, David E; Adamson, Philip D; Min, James K

2018-04-13

This study sought to compare the performance of history-based risk scores in predicting obstructive coronary artery disease (CAD) among patients with stable chest pain from the SCOT-HEART study. Risk scores for estimating pre-test probability of CAD are derived from referral-based populations with a high prevalence of disease. The generalizability of these scores to lower prevalence populations in the initial patient encounter for chest pain is uncertain. We compared 3 scores among patients with suspected CAD in the coronary computed tomographic angiography (CTA) randomized arm of the SCOT-HEART study for the outcome of obstructive CAD by coronary CTA: the updated Diamond-Forrester score (UDF), CAD Consortium clinical score (CAD2), and CONFIRM risk score (CRS). We tested calibration with goodness-of-fit, discrimination with area under the receiver-operating curve (AUC), and reclassification with net reclassification improvement (NRI) to identify low-risk patients. In 1,738 patients (58 ± 10 years and 44.0% women), overall calibration was best for UDF, with underestimation by CRS and CAD2. Discrimination by AUC was highest for CAD2 at 0.79 (95% confidence interval [CI]: 0.77 to 0.81) than for UDF (0.77 [95% CI: 0.74 to 0.79]) or CRS (0.75 [95% CI: 0.73 to 0.77]) (p CAD2 (NRI 0.31, 95% CI: 0.27 to 0.35) followed by CRS (NRI 0.21, 95% CI: 0.17 to 0.25) compared with UDF (p CAD and uniform CAD evaluation by coronary CTA, CAD2 provided the best discrimination and classification, despite overestimation of obstructive CAD as evaluated by coronary CTA. CRS exhibited intermediate performance followed by UDF for discrimination and reclassification. Copyright © 2018. Published by Elsevier Inc.

Nucleotide Selectivity in Abiotic RNA Polymerization Reactions

Science.gov (United States)

Coari, Kristin M.; Martin, Rebecca C.; Jain, Kopal; McGown, Linda B.

2017-09-01

In order to establish an RNA world on early Earth, the nucleotides must form polymers through chemical rather than biochemical reactions. The polymerization products must be long enough to perform catalytic functions, including self-replication, and to preserve genetic information. These functions depend not only on the length of the polymers, but also on their sequences. To date, studies of abiotic RNA polymerization generally have focused on routes to polymerization of a single nucleotide and lengths of the homopolymer products. Less work has been done the selectivity of the reaction toward incorporation of some nucleotides over others in nucleotide mixtures. Such information is an essential step toward understanding the chemical evolution of RNA. To address this question, in the present work RNA polymerization reactions were performed in the presence of montmorillonite clay catalyst. The nucleotides included the monophosphates of adenosine, cytosine, guanosine, uridine and inosine. Experiments included reactions of mixtures of an imidazole-activated nucleotide (ImpX) with one or more unactivated nucleotides (XMP), of two or more ImpX, and of XMP that were activated in situ in the polymerization reaction itself. The reaction products were analyzed using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) to identify the lengths and nucleotide compositions of the polymerization products. The results show that the extent of polymerization, the degree of heteropolymerization vs. homopolymerization, and the composition of the polymeric products all vary among the different nucleotides and depend upon which nucleotides and how many different nucleotides are present in the mixture.

Nucleotide Selectivity in Abiotic RNA Polymerization Reactions.

Science.gov (United States)

Coari, Kristin M; Martin, Rebecca C; Jain, Kopal; McGown, Linda B

2017-09-01

In order to establish an RNA world on early Earth, the nucleotides must form polymers through chemical rather than biochemical reactions. The polymerization products must be long enough to perform catalytic functions, including self-replication, and to preserve genetic information. These functions depend not only on the length of the polymers, but also on their sequences. To date, studies of abiotic RNA polymerization generally have focused on routes to polymerization of a single nucleotide and lengths of the homopolymer products. Less work has been done the selectivity of the reaction toward incorporation of some nucleotides over others in nucleotide mixtures. Such information is an essential step toward understanding the chemical evolution of RNA. To address this question, in the present work RNA polymerization reactions were performed in the presence of montmorillonite clay catalyst. The nucleotides included the monophosphates of adenosine, cytosine, guanosine, uridine and inosine. Experiments included reactions of mixtures of an imidazole-activated nucleotide (ImpX) with one or more unactivated nucleotides (XMP), of two or more ImpX, and of XMP that were activated in situ in the polymerization reaction itself. The reaction products were analyzed using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) to identify the lengths and nucleotide compositions of the polymerization products. The results show that the extent of polymerization, the degree of heteropolymerization vs. homopolymerization, and the composition of the polymeric products all vary among the different nucleotides and depend upon which nucleotides and how many different nucleotides are present in the mixture.

The Fermi Gamma Ray Space Telescope discovers the Pulsar in the Young Galactic Supernova-Remnant CTA 1

International Nuclear Information System (INIS)

Abdo, Aous A.; Ackermann, M.; Atwood, W.B.; Baldini, L.; Ballet, J.; Barbiellini, G.; Baring, M.G.; Bastieri, Denis; Baughman, B.M.; Bechtol, K.; Bellazzini, R.; Berenji, B.; Blandford, R.D.; Bloom, Elliott D.; Bogaert, G.; Bonamente, E.; Borgland, A.W.; Bregeon, J.; Brez, A.; Brigida, M.; Bruel, P.

2009-01-01

Energetic young pulsars and expanding blast waves (supernova remnants, SNRs) are the most visible remains after massive stars, ending their lives, explode in core-collapse supernovae. The Fermi Gamma-Ray Space Telescope has unveiled a radio quiet pulsar located near the center of the compact synchrotron nebula inside the supernova remnant CTA 1. The pulsar, discovered through its gamma-ray pulsations, has a period of 316.86 ms, a period derivative of 3.614 x 10 -13 s s -1 . Its characteristic age of 10 4 years is comparable to that estimated for the SNR. It is conjectured that most unidentified Galactic gamma ray sources associated with star-forming regions and SNRs are such young pulsars

The Fermi Gamma Ray Space Telescope discovers the Pulsar in the Young Galactic Supernova-Remnant CTA 1

Energy Technology Data Exchange (ETDEWEB)

Abdo, Aous A.; Ackermann, M.; Atwood, W.B.; Baldini, L.; Ballet, J.; Barbiellini, G.; Baring, M.G.; Bastieri, Denis; Baughman, B.M.; Bechtol, K.; Bellazzini, R.; Berenji, B.; Blandford, R.D.; Bloom, Elliott D.; Bogaert, G.; Bonamente, E.; Borgland, A.W.; Bregeon, J.; Brez, A.; Brigida, M.; Bruel, P.

2009-05-15

Energetic young pulsars and expanding blast waves (supernova remnants, SNRs) are the most visible remains after massive stars, ending their lives, explode in core-collapse supernovae. The Fermi Gamma-Ray Space Telescope has unveiled a radio quiet pulsar located near the center of the compact synchrotron nebula inside the supernova remnant CTA 1. The pulsar, discovered through its gamma-ray pulsations, has a period of 316.86 ms, a period derivative of 3.614 x 10{sup -13} s s{sup -1}. Its characteristic age of 10{sup 4} years is comparable to that estimated for the SNR. It is conjectured that most unidentified Galactic gamma ray sources associated with star-forming regions and SNRs are such young pulsars.

Studies on Rate Enhancement of Polymerization in NMRP

Institute of Scientific and Technical Information of China (English)

HUANG Jian-ying; XU Miao-qing; YAN Ming-fa; CHEN Yi-hong; CHU Jia-yan; ZHUANG Jia-ming; DAI Li-zong; ZOU You-si

2005-01-01

In NMRP, the polymerization of MMA, the polymerization of St and the copolymerization of MMA with St were distinctly accelerated by the addition of a small amount of MN. The polymerization proceeds in a living fashion as indicated by the increase in molecular weight with the increase of time and conversion and a relatively low polydispersity. It has been found that the addition of MN results in a nearly one hundred times higher rate of the polymerization of MMA, a nearly twenty times higher rate of the polymerization of St and a nearly fifteen times higher rate of the copolymerization of St and MMA.

Impact of imaging quality of change pitch on coronary CTA with 64-detector row CT

International Nuclear Information System (INIS)

Li Xiang; Jin Chaolin; Zhang Shutong

2009-01-01

Objective: To investigate the impact of imaging quality of pitch on coronary CT angiography (CTA) with 64-detector row CT. Methods: 566 patients were divided into four groups according to heart rate (≤ 50, 51 ∼ 70, 71 ∼ 80 and ≥ 80 bpm). Three dimensional reconstructions were used such as volume rendering (VR), maximum intensity projection(MIP) and curved planar reformation (CPR). Each group was divided into control group and experimential group randomly, using normal pitch and revised pitch respectively, and the imaging quality and influencing factors were analyzed among the four groups. Results: There was significant difference in imaging quality among the four groups (P < 0.05). Each group had difference in imaging quality with normal pitch and revised pitch. Conclusions: The revised pitch helps to improve the imaging quality and meet the demand of diagnosis. (authors)

Preparation and certification of the Polish reference material Virginia Tobacco Leaves (CTA-VTL-2) for inorganic trace analysis including microanalysis

International Nuclear Information System (INIS)

Dybczynski, R.; Polkowska-Motrenko, H.; Samczynski, Z.; Szopa, Z.

1997-01-01

A new Polish certified reference material Virginia Tobacco Leaves (CTA-VTL-2) for inorganic trace analysis including microanalysis has been prepared. Certification of the candidate reference material was based on the world-wide interlaboratory comparison in which 60 laboratories from 18 countries, participated using various analytical methods and techniques. Data evaluation performed by means of the new multifunctional software package -SSQC. Recommended values were assigned for 33 and 'information' values for 10 elements, respectively. The validity of 'certified' values was confirmed for several elements using 'very accurate' methods developed in this Laboratory. (author)

The pattern and prevalence of vertebral artery injury in patients with cervical spine fractures

Directory of Open Access Journals (Sweden)

Farzanah Ismail

2013-06-01

Method: A retrospective review of patients who had undergone CTA of the vertebral arteries was undertaken. Reports were reviewed to determine which patients met the inclusion criteria of having had both cervical spine fractures and CTA of the vertebral arteries. Images of patients who met the inclusion criteria were analysed by a radiologist. Results: The prevalence of vertebral artery injury was 33%. Four out of the 11 patients who had vertebral artery injury, had post-traumatic spasm of the artery, with associated thrombosis or occlusion of the vessel. In terms of blunt carotid vertebral injury (BCVI grading, most of the patients sustained grade IV injuries. Four patients who had vertebral artery injury had fractures of the upper cervical vertebrae, i.e. C1 to C3. Fifteen transverse process fractures were associated with vertebral artery injury. No vertebral artery injury was detected in patients who had facet joint subluxations. Conclusion: Patients with transverse process fractures of the cervical spine and upper cervical vertebral body fractures should undergo CTA to exclude vertebral artery injury.

Nonperturbative Renormalization Group Approach to Polymerized Membranes

Science.gov (United States)

Essafi, Karim; Kownacki, Jean-Philippe; Mouhanna, Dominique

2014-03-01

Membranes or membrane-like materials play an important role in many fields ranging from biology to physics. These systems form a very rich domain in statistical physics. The interplay between geometry and thermal fluctuations lead to exciting phases such flat, tubular and disordered flat phases. Roughly speaking, membranes can be divided into two group: fluid membranes in which the molecules are free to diffuse and thus no shear modulus. On the other hand, in polymerized membranes the connectivity is fixed which leads to elastic forces. This difference between fluid and polymerized membranes leads to a difference in their critical behaviour. For instance, fluid membranes are always crumpled, whereas polymerized membranes exhibit a phase transition between a crumpled phase and a flat phase. In this talk, I will focus only on polymerized phantom, i.e. non-self-avoiding, membranes. The critical behaviour of both isotropic and anisotropic polymerized membranes are studied using a nonperturbative renormalization group approach (NPRG). This allows for the investigation of the phase transitions and the low temperature flat phase in any internal dimension D and embedding d. Interestingly, graphene behaves just as a polymerized membrane in its flat phase.

Abrasion of Polymeric Composites on Basis of Machining Splinters from Hardfacing Alloys – Usable in Agrocomplex

Directory of Open Access Journals (Sweden)

Petr Valášek

2014-01-01

Full Text Available A paper focuses on a description of two-body and three-body abrasion wear of polymeric particle composites with fillers on a basis of machining splinters from hardfacing alloys. The abrasive wear is typical for functional surfaces of agricultural machines processing the soil. One of possibilities of the functional surface renovation is an application of resistant layers in a form of composite systems. Just the inclusion of hard inorganic particles into a polymeric matrix significantly increases its wear resistance. So long as the primary filler is replaced by the waste – by particles from the material machining – the matrix in which the filler is dispersed is a bearer of a material recyclation. This way of the recyclation is inexpensive, economic and sensitive to environment. The paper focuses on the experimental description of the two-body and three-body abrasion and the composites hardness, it describes a production of a prototype for field tests with the functional surface on the basis of the investigated composite system at the same time.

AZIDE-ALKYNE CLICK POLYMERIZATION: AN UPDATE

Institute of Scientific and Technical Information of China (English)

Hong-kun Li; Jing-zhi Sun; An-jun Qin; Ben Zhong Tang

2012-01-01

The great achievements of click chemistry have encouraged polymer scientists to use this reaction in their field.This review assembles an update of the advances of using azide-alkyne click polymerization to prepare functional polytriazoles (PTAs) with linear and hyperbranched structures.The Cu(Ⅰ)-mediated click polymerization furnishes 1,4-regioregular PTAs,whereas,the metal-free click polymerization of propiolates and azides produces PTAs with 1,4-regioisomer contents up to 90％.The PTAs display advanced functions,such as aggregation-induced emission,thermal stability,biocompatibility and optical nonlinearity.

Evaluation of Isoprene Chain Extension from PEO Macromolecular Chain Transfer Agents for the Preparation of Dual, Invertible Block Copolymer Nanoassemblies.

Science.gov (United States)

Bartels, Jeremy W; Cauët, Solène I; Billings, Peter L; Lin, Lily Yun; Zhu, Jiahua; Fidge, Christopher; Pochan, Darrin J; Wooley, Karen L

2010-09-14

Two RAFT-capable PEO macro-CTAs, 2 and 5 kDa, were prepared and used for the polymerization of isoprene which yielded well-defined block copolymers of varied lengths and compositions. GPC analysis of the PEO macro-CTAs and block copolymers showed remaining unreacted PEO macro-CTA. Mathematical deconvolution of the GPC chromatograms allowed for the estimation of the blocking efficiency, about 50% for the 5 kDa PEO macro-CTA and 64% for the 2 kDa CTA. Self assembly of the block copolymers in both water and decane was investigated and the resulting regular and inverse assemblies, respectively, were analyzed with DLS, AFM, and TEM to ascertain their dimensions and properties. Assembly of PEO-b-PIp block copolymers in aqueous solution resulted in well-defined micelles of varying sizes while the assembly in hydrophobic, organic solvent resulted in the formation of different morphologies including large aggregates and well-defined cylindrical and spherical structures.

Fluorescent polymeric nanocomposite films generated by surface-mediated photoinitiation of polymerization

International Nuclear Information System (INIS)

Avens, Heather J.; Chang, Erin L.; May, Allison M.; Berron, Brad J.; Seedorf, Gregory J.; Balasubramaniam, Vivek; Bowman, Christopher N.

2011-01-01

Incorporation of nanoparticles (NPs) into polymer films represents a valuable strategy for achieving a variety of desirable physical, optical, mechanical, and electrical attributes. Here, we describe and characterize the creation of highly fluorescent polymer films by entrapment of fluorescent NPs into polymer matrices through surface-mediated eosin photoinitiation reactions. Performing surface-mediated polymerizations with NPs combines the benefits of a covalently anchored film with the unique material properties afforded by NPs. The effects of monomer type, crosslinker content, NP size, and NP surface chemistry were investigated to determine their impact on the relative amount of NPs entrapped in the surface-bound films. The density of entrapped NPs was increased up to 6-fold by decreasing the NP diameter. Increasing the crosslinking agent concentration enabled a greater than 2-fold increase in the amount of NPs entrapped. Additionally, the monomer chemistry played a significant role as poly(ethylene glycol) diacrylate (PEGDA)-based monomer formulations entrapped a 10-fold higher density of carboxy-functionalized NPs than did acrylamide/bisacrylamide formulations, though the latter formulations ultimately immobilized more fluorophores by generating thicker films. In the context of a polymerization-based microarray biodetection platform, these findings enabled tailoring of the monomer and NP selection to yield a 200-fold improvement in sensitivity from 31 (±1) to 0.16 (±0.01) biotinylated target molecules per square micron. Similarly, in polymerization-based cell staining applications, appropriate monomer and NP selection enabled facile visualization of microscale, sub-cellular features. Careful consideration of monomer and NP selection is critical to achieve the desired properties in applications that employ surface-mediated polymerization to entrap NPs.

Constructive Technology Assessment (CTA) as a tool in coverage with evidence development: the case of the 70-gene prognosis signature for breast cancer diagnostics.

Science.gov (United States)

Retèl, Valesca P; Bueno-de-Mesquita, Jolien M; Hummel, Marjan J M; van de Vijver, Marc J; Douma, Kirsten F L; Karsenberg, Kim; van Dam, Frits S A M; van Krimpen, Cees; Bellot, Frank E; Roumen, Rudi M H; Linn, Sabine C; van Harten, Wim H

2009-01-01

Constructive Technology Assessment (CTA) is a means to guide early implementation of new developments in society, and can be used as an evaluation tool for Coverage with Evidence Development (CED). We used CTA for the introduction of a new diagnostic test in the Netherlands, the 70-gene prognosis signature (MammaPrint) for node-negative breast cancer patients. Studied aspects were (organizational) efficiency, patient-centeredness and diffusion scenarios. Pre-post structured surveys were conducted in fifteen community hospitals concerning changes in logistics and teamwork as a consequence of the introduction of the 70-gene signature. Patient-centeredness was measured by questionnaires and interviews regarding knowledge and psychological impact of the test. Diffusion scenarios, which are commonly applied in industry to anticipate on future development and diffusion of their products, have been applied in this study. Median implementation-time of the 70-gene signature was 1.2 months. Most changes were seen in pathology processes and adjuvant treatment decisions. Physicians valued the addition of the 70-gene signature information as beneficial for patient management. Patient-centeredness (n = 77, response 78 percent): patients receiving a concordant high-risk and discordant clinical low/high risk-signature showed significantly more negative emotions with respect to receiving both test-results compared with concordant low-risk and discordant clinical high/low risk-signature patients. The first scenario was written in 2004 before the introduction of the 70-gene signature and identified hypothetical developments that could influence diffusion; especially the "what-if" deviation describing a discussion on validity among physicians proved to be realistic. Differences in speed of implementation and influenced treatment decisions were seen. Impact on patients seems especially related to discordance and its successive communication. In the future, scenario drafting will lead

A new lithography of functional plasma polymerized thin films

International Nuclear Information System (INIS)

Kim, Sung-O

2001-01-01

The preparation of the resist for the vacuum lithography was carried out by plasma polymerization. The resist manufactured by plasma polymerization is a monomer produced by MMA (Methyl methacrylate). The functional groups of MMA appeared in the PPMMA (Plasma Polymerized Methyl methacrylate) as well, and this was confirmed through an analysis using FT-IR. The polymerization rate increased as a function of the plasma power and decreased as a function of the system pressure. The sensitivity and contrast of the plasma polymerized thin films were 15 μC/cm2 and 4.3 respectively. The size of the pattern manufactured by Vacuum Lithography using the plasma polymerized thin films was 100 nm

Simultaneous AuIII Extraction and In Situ Formation of Polymeric Membrane-Supported Au Nanoparticles: A Sustainable Process with Application in Catalysis.

Science.gov (United States)

Mora-Tamez, Lucía; Esquivel-Peña, Vicente; Ocampo, Ana L; Rodríguez de San Miguel, Eduardo; Grande, Daniel; de Gyves, Josefina

2017-04-10

A polymeric membrane-supported catalyst with immobilized gold nanoparticles (AuNPs) was prepared through the extraction and in situ reduction of Au III salts in a one-step strategy. Polymeric inclusion membranes (PIMs) and polymeric nanoporous membranes (PNMs) were tested as different membrane-support systems. Transport experiments indicated that PIMs composed of cellulose triacetate, 2-nitrophenyloctyl ether, and an aliphatic tertiary amine (Adogen 364 or Alamine 336) were the most efficient supports for Au III extraction. The simultaneous extraction and reduction processes were proven to be the result of a synergic phenomenon in which all the membrane components were involved. Scanning electron microscopy characterization of cross-sectional samples suggested a distribution of AuNPs throughout the membrane. Transmission electron microscopy characterization of the AuNPs indicated average particle sizes of 36.7 and 2.9 nm for the PIMs and PNMs, respectively. AuNPs supported on PIMs allowed for >95.4 % reduction of a 0.05 mmol L -1 4-nitrophenol aqueous solution with 10 mmol L -1 NaBH 4 solution within 25 min. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Comparison of 64-slice computed tomography angiography and coronary angiography for the detection and assessment of coronary artery disease in patients with angina: A systematic review

International Nuclear Information System (INIS)

Powell, H.; Cosson, P.

2013-01-01

Background: Coronary artery disease (CAD) is the leading cause of death in Western countries. It presents itself in various ways, the commonest being angina. According to the Royal College of Radiologist referral guidelines, Coronary Angiography (CA) is currently the gold standard for diagnosis and evaluation of CAD. However, due to the invasive nature and expense of CA there is a perceived need for a primary non-invasive imaging modality to supersede it. Computed tomography angiography (CTA), utilising 64-slice technology, may be a less invasive alternative to CA. Aim: To consider the research evidence for the current gold standard diagnostic test for CAD. Specifically, which is more sensitive and specific for detecting CAD in patients with angina; 64-slice CTA or CA? Inclusion Criteria: Prospective, non-randomised control trials and diagnostic accuracy studies comparing 64-slice CTA and CA were included. Participants were adults with angina with suspected or known CAD. Method: An electronic search of the databases; AMED, CINAHL, Cochrane Library, EMBASE, MEDLINE and Science Direct, was conducted between January 2004 and April 2012. Secondary hand-searching of grey literature was undertaken. Two reviewers independently determined studies for inclusion, assessed quality, using SIGN50, and extracted data. Diagnostic value of 64-slice CTA and CA was compared and analysed at patient and segment level. Results: Ten studies were included in the critical review enrolling 1188 patients. At patient level sensitivity for 64-slice CTA ranged from 88% to 100%, specificity 64–92%, PPV 86–97% and NPV 76.9–100%. At segment level sensitivity for 64-slice CTA ranged from 73% to 100%, specificity 83–98%, PPV 47–90% and NPV 89–100% Conclusion: At both patient and segment level, 64-slice CTA is a highly sensitive and specific non-invasive alternative to CA for diagnosis of significant stenosis in patients with angina. For standalone diagnosis of CAD current research would

Cross-linking of polymeric materials

International Nuclear Information System (INIS)

Bloom, L.I.; Du Plessis, T.A.; Meij, G.O.

1991-01-01

The invention provides a method of producing a cured polymeric artifact from a polymeric thermoplastic starting material, the material of the artifact having reduced thermoplasticity relative to the starting material and exhibiting an enhanced degree of cross-linking relative to the starting material. The method includes subjecting a polymeric thermoplastic starting material, which is capable of being cross-linked by irradiation, to sufficient irradiation partially to cross-linked the starting material to produce a thermoplastic partially cross-linked intermediate material. The thermoplasticity of the intermediate material is then reduced by heating it to raise its melting point. The invention also provides a method of making a partially cross-linked feedstocks and a master batch for use in making such artifacts

Fluid Effects in Polymers and Polymeric Composites

CERN Document Server

Weitsman, Y Jack

2012-01-01

Fluid Effects in Polymers and Polymeric Composites, written by the late Dr. Y. Jack Weitsman, addresses the wide range of parameters that affect the interaction of fluids with polymers and polymeric composites. The book aims at broadening the scope of available data, mostly limited up to this time to weight-gain recordings of fluid ingress into polymers and composites, to the practical circumstances of fluctuating exposure. Various forms of experimental data are given, in conjunction with theoretical models derived from basic scientific principles, and correlated with severity of exposure conditions and interpreted by means of rationally based theoretical models. The practical implications of the effects of fluids are discussed. The issue of fluid effects on polymers and polymeric composites is of concern to engineers and scientists active in aerospace and naval structures, as an increasing portion of these structures are made of polymeric composites and employ polymeric adhesives as a joining device. While...

Tubulin polymerization-stimulating activity of Ganoderma triterpenoids.

Science.gov (United States)

Kohno, Toshitaka; Hai-Bang, Tran; Zhu, Qinchang; Amen, Yhiya; Sakamoto, Seiichi; Tanaka, Hiroyuki; Morimoto, Satoshi; Shimizu, Kuniyoshi

2017-04-01

Tubulin polymerization is an important target for anticancer therapies. Even though the potential of Ganoderma triterpenoids against various cancer targets had been well documented, studies on their tubulin polymerization-stimulating activity are scarce. This study was conducted to evaluate the effect of Ganoderma triterpenoids on tubulin polymerization. A total of twenty-four compounds were investigated using an in vitro tubulin polymerization assay. Results showed that most of the studied triterpenoids exhibited microtuble-stabilizing activity to different degrees. Among the investigated compounds, ganoderic acid T-Q, ganoderiol F, ganoderic acid S, ganodermanontriol and ganoderic acid TR were found to have the highest activities. A structure-activity relationship (SAR) analysis was performed. Extensive investigation of the SAR suggests the favorable structural features for the tubulin polymerization-stimulating activity of lanostane triterpenes. These findings would be helpful for further studies on the potential mechanisms of the anticancer activity of Ganoderma triterpenoids and give some indications on the design of tubulin-targeting anticancer agents.

A qualitative chemometric study of resin composite polymerization

Directory of Open Access Journals (Sweden)

Regina Ferraz Mendes

2008-01-01

Full Text Available Objective: An experiment was carried out to assess the effect produced by different polymerization techniques on resin composite color after it has been immersed in coffee. Methods: Samples were manufactured using TPH Spectrum composite. It was polymerized for 10 or 40 seconds, with the light tip at one or zero millimeters from the resin surface, and afterwards the samples were immersed in coffee for 24 hours or 7 days. Ten different evaluators classified the samples according to their degree of staining. Results: The samples that were polymerized for 10 seconds were more susceptible to staining than the ones polymerized by 40 seconds. Samples immersed in coffee for 7 days were more susceptible to staining than the ones immersed for 24 hours. Conclusion: The variables polymerization time and immersion time were determinant in the staining susceptibility of the studied composite by coffee. However, there was no significant difference, irrespective of whether the resin was polymerized 10 or zero millimeters away from the resin surface.

Volumetric polymerization shrinkage of contemporary composite resins

OpenAIRE

Nagem Filho, Halim; Nagem, Haline Drumond; Francisconi, Paulo Afonso Silveira; Franco, Eduardo Batista; Mondelli, Rafael Francisco Lia; Coutinho, Kennedy Queiroz

2007-01-01

The polymerization shrinkage of composite resins may affect negatively the clinical outcome of the restoration. Extensive research has been carried out to develop new formulations of composite resins in order to provide good handling characteristics and some dimensional stability during polymerization. The purpose of this study was to analyze, in vitro, the magnitude of the volumetric polymerization shrinkage of 7 contemporary composite resins (Definite, Suprafill, SureFil, Filtek Z250, Fill ...

Deformation and flow of polymeric materials

CERN Document Server

Münstedt, Helmut

2014-01-01

This book describes the properties of single polymer molecules and polymeric materials and the methods how to characterize them. Molar masses, molar mass distributions and branching structure are discussed in detail. These properties are decisive for a deeper understanding of structure/properties relationships of polymeric materials. This book therefore describes and discusses them in detail. The mechanical behavior as a function of time and temperature is a key subject of the book. The authors present it on the basis of many original results they have obtained in their long research careers. They present the temperature dependence of mechanical properties of various polymeric materials in a wide temperature range: from cryogenic temperatures to the melt. Besides an extensive data collection on the transitions of various different polymeric materials, they also carefully present the physical explanations of the observed phenomena. Glass transition and melting temperatures are discussed, particularly, with the...

Thermal polymerization of Moringa oleifera oil

International Nuclear Information System (INIS)

Melo, Tania M.S.; Novack, Katia M.; Leandro, Cristiano

2011-01-01

It is increasingly clear both for society and the scientific community, that is necessary to find alternatives to reduce the use of polymeric materials because of their damage to the environment. One way to minimize the environmental problems related to the use of polymers is try to make them quickly degradable. In this study it was obtained a material with polymeric appearance derived from heating of the vegetable oil extracted from seeds of Moringa oleifera. The resulting product is an interesting alternative to obtain polymeric materials that may have biodegradable characteristics, coming from a renewable source and low cost. Moringa oil can be used since it has a high content of unsaturated fatty acids, and its main constituent oleic acid. All samples were characterized by FTIR, NMR and GPC. It was obtained a polymeric material, malleable, high viscosity, with some elasticity, low crystallinity and no unpleasant odor. (author)

21 CFR 870.3650 - Pacemaker polymeric mesh bag.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Pacemaker polymeric mesh bag. 870.3650 Section 870...) MEDICAL DEVICES CARDIOVASCULAR DEVICES Cardiovascular Prosthetic Devices § 870.3650 Pacemaker polymeric mesh bag. (a) Identification. A pacemaker polymeric mesh bag is an implanted device used to hold a...

Cascade synthesis of chiral block copolymers combining lipase catalyzed ring opening polymerization and atom transfer radical polymerization

NARCIS (Netherlands)

Peeters, J.W.; Palmans, A.R.A.; Veld, M.A.J.; Scheijen, F.J.E.; Heise, A.; Meijer, E.W.

2004-01-01

The enantioselective polymerization of methyl-substituted -caprolactones using Novozym 435 as the catalyst was investigated. All substituted monomers could be polymerized except 6-methyl--caprolactone (6-MeCL), which failed to propagate after ring opening. Interestingly, an odd-even effect in the

FtsZ Polymerization Assays : Simple Protocols and Considerations

NARCIS (Netherlands)

Król, Ewa; Scheffers, Dirk-Jan

2013-01-01

During bacterial cell division, the essential protein FtsZ assembles in the middle of the cell to form the so-called Z-ring. FtsZ polymerizes into long filaments in the presence of GTP in vitro, and polymerization is regulated by several accessory proteins. FtsZ polymerization has been extensively

Glycine Polymerization on Oxide Minerals

Science.gov (United States)

Kitadai, Norio; Oonishi, Hiroyuki; Umemoto, Koichiro; Usui, Tomohiro; Fukushi, Keisuke; Nakashima, Satoru

2017-06-01

It has long been suggested that mineral surfaces played an important role in peptide bond formation on the primitive Earth. However, it remains unclear which mineral species was key to the prebiotic processes. This is because great discrepancies exist among the reported catalytic efficiencies of minerals for amino acid polymerizations, owing to mutually different experimental conditions. This study examined polymerization of glycine (Gly) on nine oxide minerals (amorphous silica, quartz, α-alumina and γ-alumina, anatase, rutile, hematite, magnetite, and forsterite) using identical preparation, heating, and analytical procedures. Results showed that a rutile surface is the most effective site for Gly polymerization in terms of both amounts and lengths of Gly polymers synthesized. The catalytic efficiency decreased as rutile > anatase > γ-alumina > forsterite > α- alumina > magnetite > hematite > quartz > amorphous silica. Based on reported molecular-level information for adsorption of Gly on these minerals, polymerization activation was inferred to have arisen from deprotonation of the NH3 + group of adsorbed Gly to the nucleophilic NH2 group, and from withdrawal of electron density from the carboxyl carbon to the surface metal ions. The orientation of adsorbed Gly on minerals is also a factor influencing the Gly reactivity. The examination of Gly-mineral interactions under identical experimental conditions has enabled the direct comparison of various minerals' catalytic efficiencies and has made discussion of polymerization mechanisms and their relative influences possible Further systematic investigations using the approach reported herein (which are expected to be fruitful) combined with future microscopic surface analyses will elucidate the role of minerals in the process of abiotic peptide bond formation.

Glycine Polymerization on Oxide Minerals.

Science.gov (United States)

Kitadai, Norio; Oonishi, Hiroyuki; Umemoto, Koichiro; Usui, Tomohiro; Fukushi, Keisuke; Nakashima, Satoru

2017-06-01

It has long been suggested that mineral surfaces played an important role in peptide bond formation on the primitive Earth. However, it remains unclear which mineral species was key to the prebiotic processes. This is because great discrepancies exist among the reported catalytic efficiencies of minerals for amino acid polymerizations, owing to mutually different experimental conditions. This study examined polymerization of glycine (Gly) on nine oxide minerals (amorphous silica, quartz, α-alumina and γ-alumina, anatase, rutile, hematite, magnetite, and forsterite) using identical preparation, heating, and analytical procedures. Results showed that a rutile surface is the most effective site for Gly polymerization in terms of both amounts and lengths of Gly polymers synthesized. The catalytic efficiency decreased as rutile > anatase > γ-alumina > forsterite > α- alumina > magnetite > hematite > quartz > amorphous silica. Based on reported molecular-level information for adsorption of Gly on these minerals, polymerization activation was inferred to have arisen from deprotonation of the NH 3 + group of adsorbed Gly to the nucleophilic NH 2 group, and from withdrawal of electron density from the carboxyl carbon to the surface metal ions. The orientation of adsorbed Gly on minerals is also a factor influencing the Gly reactivity. The examination of Gly-mineral interactions under identical experimental conditions has enabled the direct comparison of various minerals' catalytic efficiencies and has made discussion of polymerization mechanisms and their relative influences possible Further systematic investigations using the approach reported herein (which are expected to be fruitful) combined with future microscopic surface analyses will elucidate the role of minerals in the process of abiotic peptide bond formation.

Gamma Radiation-Induced Template Polymerization Technique

International Nuclear Information System (INIS)

Siyam, T.

2005-01-01

Gamma radiation induced copolymerization of acrylamide sodiumacrylate (AM-AANa) in the presence and absence of the polymer additive was studied at low monomer concentration(1.4M/l). The results showed that the exponents of the dose rate for the polymerization rate was found to be 1.3 and 1.4 in the absence and in the presence of the polymer additive respectively. The molecular weight of the formed polymer increased by addition of the polymer to the system. In the presence of the polymer the comonomers polymerize on the added polymer. In the absence of the added polymer the comonomers polymerize according to the copolymerization process at the initial stage of the copolymerization. While at high conversion the residual comonomers polymerize on the formed macromolecular chains of the produced polymer. These studies showed that the copolymerization in the presence of added polymer is completely template copolymerization while in the absence of the polymer the copolymerization process is only template process with a high conversion

Radiation sterilization of polymeric implant materials

International Nuclear Information System (INIS)

Bruck, S.D.; Mueller, E.P.

1988-01-01

High-energy irradiation sterilization of medical devices and implants composed of polymeric biomaterials that are in contact with tissue and/or blood, may adversely affect their long-term mechanical and/or biological performance (tissue and/or blood compatibility). Since many polymeric implants may contain trace quantities of catalysts and/or other additives, the effect of high-energy radiation on these additives, and possible synergistic effects with the polymer chains under the influence of high-energy radiation, must be considered. It is essential to indicate whether polymeric implants are used in short-term (acute) or long-term (chronic) applications. Relatively small changes in their physicochemical, mechanical, and biological properties may be tolerable in the short term, whereas similar changes may lead to catastrophic failures in long-term applications. Therefore, polymeric implants which are to be sterilized by high-energy irradiation should be carefully evaluated for long-term property changes which may be induced by the radiation

Polypropylene/graphite nanocomposites by in situ polymerization

International Nuclear Information System (INIS)

Milani, Marceo A.; Galland, Giselda B.; Quijada, Raul

2011-01-01

This work presents the synthesis of nanocomposites of polypropylene/graphite by in situ polymerization using metallocene catalyst and graphene nanosheets. Initially was analyzed which of the metallocene catalysts rac-Et(Ind) 2 ZrCl 2 or rac-Me 2 Si(Ind) 2 ZrCl 2 produces polypropylene with mechanical properties more relevant. Then it were performed the in situ polymerization reactions to obtain the nanocomposites. The polymeric materials were characterized by XRD, DSC, GPC and DMTA. (author)

Preparation of nanoencapsulated phase change material as latent functionally thermal fluid

Energy Technology Data Exchange (ETDEWEB)

Fang Yutang; Kuang Shengyan; Gao Xuenong; Zhang Zhengguo, E-mail: ppytfang@scut.edu.c [Key Laboratory of Enhanced Heat Transfer and Energy Conservation, Ministry of Education, South China University of Technology, Guangzhou 510640 (China)

2009-02-07

Nanoencapsulated phase change material with polystyrene as the shell and n-octadecane as the core was synthesized using the ultrasonic technique and miniemulsion in situ polymerization. The influences of polymerization factors, including initiator, chain transfer agent (CTA), surfactant, n-octadecane/styrene ratio and hydrophilic co-monomer, on the morphology and thermophysical properties of nanocapsules were systematically investigated. The optimized polymerization conditions were 0.5 wt% of initiator (2,2-azobisisobutyronitrile), 0.4 wt% of CTA (n-dodecyl mercaptan), 2% of composite surfactants which were composed of sodium dodecyl sulfate and poly-(ethylene glycol) monooctylphenyl ether by 1 : 1 in weight ratio, 1 wt% of hydrophilic co-monomer butyl acrylate or 3 wt% of methyl methacrylate and 1 : 1 n-octadecane to styrene in weight ratio. Under these conditions, the z-average size of prepared nanocapsules was 124 nm and the phase change enthalpy was 124.4 kJ kg{sup -1}. The heat capacity was as high as 11.61 kJ kg{sup -1} K{sup -1} at the latex concentration of 20.6 wt%. Thermal stability and viscosity testing show that this fluid had excellent resistance to thermal shock (after 100 cycles, no liquid Oct was observed during heating) and low viscosity (only 3.61 mPa s at the latex concentration of 20.6 wt%), which seems to be promising as a latent functionally thermal fluid.

Preparation and certification of the Polish reference material Virginia Tobacco Leaves (CTA-VTL-2) for inorganic trace analysis including microanalysis

Energy Technology Data Exchange (ETDEWEB)

Dybczynski, R.; Polkowska-Motrenko, H.; Samczynski, Z.; Szopa, Z.

1997-12-31

A new Polish certified reference material Virginia Tobacco Leaves (CTA-VTL-2) for inorganic trace analysis including microanalysis has been prepared. Certification of the candidate reference material was based on the world-wide interlaboratory comparison in which 60 laboratories from 18 countries, participated using various analytical methods and techniques. Data evaluation performed by means of the new multifunctional software package -SSQC. Recommended values were assigned for 33 and `information` values for 10 elements, respectively. The validity of `certified` values was confirmed for several elements using `very accurate` methods developed in this Laboratory. (author). 47 refs, 28 figs, 12 tabs.

Magnetic Levitation To Characterize the Kinetics of Free-Radical Polymerization.

Science.gov (United States)

Ge, Shencheng; Semenov, Sergey N; Nagarkar, Amit A; Milette, Jonathan; Christodouleas, Dionysios C; Yuan, Li; Whitesides, George M

2017-12-27

This work describes the development of magnetic levitation (MagLev) to characterize the kinetics of free-radical polymerization of water-insoluble, low-molecular-weight monomers that show a large change in density upon polymerization. Maglev measures density, and certain classes of monomers show a large change in density when monomers covalently join in polymer chains. MagLev characterized both the thermal polymerization of methacrylate-based monomers and the photopolymerization of methyl methacrylate and made it possible to determine the orders of reaction and the Arrhenius activation energy of polymerization. MagLev also made it possible to monitor polymerization in the presence of solids (aramid fibers, and carbon fibers, and glass fibers). MagLev offers a new analytical technique to materials and polymer scientists that complements other methods (even those based on density, such as dilatometry), and will be useful in investigating polymerizations, evaluating inhibition of polymerizations, and studying polymerization in the presence of included solid materials (e.g., for composite materials).

Method for forming polymerized microfluidic devices

Science.gov (United States)

Sommer, Gregory J.; Hatch, Anson V.; Wang, Ying-Chih; Singh, Anup K.; Renzi, Ronald F.; Claudnic, Mark R.

2013-03-12

Methods for making a microfluidic device according to embodiments of the present invention include defining.about.cavity. Polymer precursor solution is positioned in the cavity, and exposed to light to begin the polymerization process and define a microchannel. In some embodiments, after the polymerization process is partially complete, a solvent rinse is performed, or fresh polymer precursor introduced into the microchannel. This may promote removal of unpolymerized material from the microchannel and enable smaller feature sizes. The polymer precursor solution may contain an iniferter. Polymerized features therefore may be capped with the iniferter, which is photoactive. The iniferter may aid later binding of a polyacrylamide gel to the microchannel surface.

Polymeric micelles as a drug carrier for tumor targeting

Directory of Open Access Journals (Sweden)

Neha M Dand

2013-01-01

Full Text Available Polymeric micelle can be targeted to tumor site by passive and active mechanism. Some inherent properties of polymeric micelle such as size in nanorange, stability in plasma, longevity in vivo, and pathological characteristics of tumor make polymeric micelles to be targeted at the tumor site by passive mechanism called enhanced permeability and retention effect. Polymeric micelle formed from the amphiphilic block copolymer is suitable for encapsulation of poorly water soluble, hydrophobic anticancer drugs. Other characteristics of polymeric micelles such as separated functionality at the outer shell are useful for targeting the anticancer drug to tumor by active mechanisms. Polymeric micelles can be conjugated with many ligands such as antibodies fragments, epidermal growth factors, α2 -glycoprotein, transferrine, and folate to target micelles to cancer cells. Application of heat and ultrasound are the alternative methods to enhance drug accumulation in tumoral cells. Targeting using micelles can also be done to tumor angiogenesis which is the potentially promising target for anticancer drugs. This review summarizes about recently available information regarding targeting the anticancer drug to the tumor site using polymeric micelles.

STUDIES ON VINYL POLYMERIZATION WITH INITIATION SYSTEM CONTAINING AMINE DERIVATIVES

Institute of Scientific and Technical Information of China (English)

QIU Kunyuan; ZHANG Jingyi; FENG Xinde(S. T. Voong)

1983-01-01

Two main types of amine-containing initiation systems were studied in this work. In the case of MMA polymerization initiated by BPO-amine (DMT, DHET, DMA) redox systems, it was found that the polymerization rate and colour stability of the polymer for different amine systems were in the following order: DMT≈DHET＞DMA. Accordingly, BPO-DMT and BPO-DHET are effective initiators. In the case of MEMA polymerization by amine (DMT, DHET, DMA) alone, it was found that the polymerization rate and the percentage of conversion for these different amine systems were in the following order: DMT≥DHET＞DMA. The polymerization rate and the percentage of conversion also increased with the increase of DMT concentration. From the kinetic investigation the rate equation of Rp=K [DMT]1/2 [MEMA]3/2 was obtained, and the overall activation energy of polymerization was calculated to be 34.3 KJ/mol (8.2 Kcal/mol). Moreover, the polymerization of MEMA in the presence of DMT was strongly inhibited by hydroquinone, indicating the polymerization being free radical in nature. From these results, the mechanism of MEMA polymerization initiated by amine was proposed.

Confronting New Demands : Inclusive Growth, Inclusive Trade ...

International Development Research Centre (IDRC) Digital Library (Canada)

Confronting New Demands : Inclusive Growth, Inclusive Trade. Policymakers, businesspeople and civil society advocates need evidence-based research to react ... understood implications, such as labour standards and intellectual property; ...

Polymeric media for tritium fixation

International Nuclear Information System (INIS)

Franz, J.A.; Burger, L.L.

1975-01-01

The synthesis and leach testing of several polymeric media for tritium fixation are presented. Tritiated bakelite, poly(acrylonitrile) and polystyrene successfully fixed tritium. Tritium leach rates at the tracer level appear to be negligible. Advantages and disadvantages of the processes are discussed, and further bench-scale investigations underway are reported. Rough cost estimates are presented for the different media and are compared with alternate approaches such as deep-well injection and long-term tank storage. Polymeric media costs are high compared to deep-well storage and are of the same order of magnitude per liter of water as for isotopic enrichment. With this limitation, polymeric media can be economically feasible only for highly concentrated tritiated wastes. It is recommended that the bakelite and polystyrene processes be examined on a larger scale to permit more accurate cost analysis and process design. (auth)

Radiation-induced in-source polymerization of acrylonitrile in urea canal complex

International Nuclear Information System (INIS)

Yoshii, Fumio; Abe, Toshihiko; Kobayashi, Yasushi.

1975-01-01

Effect of reaction conditions on the radiation-induced in-source polymerization of acrylonitrile in urea canal complex and the properties of obtained polyacrylonitriles were investigated. The results were discussed in comparison with previously reported of the post-polymerization experiments. 1) Rate of polymerization and viscosity (eta sub(sp)/C) were the highest when the molar ratio of acrylonitrile to urea in canal complex was unity. Similar results were also obtained in the post-polymerization. However, eta sub(sp)/C exhibited different behavior on polymerization time in comparison with post-polymerization. 2) The initial rate (Rsub(p)) of polymerization is proportional to the dose rate (I) at low dose rate, but at high dose rates (above 2x10 5 r/hr) makes Rsub(p) proportional to Isup(0.5). 3) Molecular weight distribution become broader with increasing polymerization time and is broad as compared with those obtained by the post-polymerization. G-value of initiation of polymerization decreased with increasing polymerization time. These value was larger than the that obtained in the post-polymerization. 4) The stereoregularity of the polyacrylonitriles was independent of the molar ratio of acrylonitrile to urea in the canal complex and conversion. 5) The appearance of the polyacrylonitriles observed by the scanning electron microscope changed from curled string to extended one as the polymerization proceed. 6) Infrared spectrum revealed the ketenimine and cyclization structure in the polyacrylonitriles obtained below -100 0 C. The content of these abnormal structures increased with increasing conversion. (auth.)

Developing a financial inclusion index and inclusive growth in India

OpenAIRE

Susanta Kumar SETHY

2016-01-01

Financial inclusion is one of the systems through which Inclusive Growth can be achieved in developing countries like India where large sections are unable or hopeless to contribute in the financial system. An inclusive financial system mobilizes more resources for productive purposes leading to higher economic growth, better opportunities and reduction of poverty. This study, proposed an Index of financial inclusion – a multidimensional measure. The Financial Inclusion Index c...

Polymer-free nanofibers from vanillin/cyclodextrin inclusion complexes: high thermal stability, enhanced solubility and antioxidant property.

Science.gov (United States)

Celebioglu, Asli; Kayaci-Senirmak, Fatma; İpek, Semran; Durgun, Engin; Uyar, Tamer

2016-07-13

Vanillin/cyclodextrin inclusion complex nanofibers (vanillin/CD-IC NFs) were successfully obtained from three modified CD types (HPβCD, HPγCD and MβCD) in three different solvent systems (water, DMF and DMAc) via an electrospinning technique without using a carrier polymeric matrix. Vanillin/CD-IC NFs with uniform and bead-free fiber morphology were successfully produced and their free-standing nanofibrous webs were obtained. The polymer-free CD/vanillin-IC-NFs allow us to accomplish a much higher vanillin loading (∼12%, w/w) when compared to electrospun polymeric nanofibers containing CD/vanillin-IC (∼5%, w/w). Vanillin has a volatile nature yet, after electrospinning, a significant amount of vanillin was preserved due to complex formation depending on the CD types. Maximum preservation of vanillin was observed for vanillin/MβCD-IC NFs which is up to ∼85% w/w, besides, a considerable amount of vanillin (∼75% w/w) was also preserved for vanillin/HPβCD-IC NFs and vanillin/HPγCD-IC NFs. Phase solubility studies suggested a 1 : 1 molar complexation tendency between guest vanillin and host CD molecules. Molecular modelling studies and experimental findings revealed that vanillin : CD complexation was strongest for MβCD when compared to HPβCD and HPγCD in vanillin/CD-IC NFs. For vanillin/CD-IC NFs, water solubility and the antioxidant property of vanillin was improved significantly owing to inclusion complexation. In brief, polymer-free vanillin/CD-IC NFs are capable of incorporating a much higher loading of vanillin and effectively preserve volatile vanillin. Hence, encapsulation of volatile active agents such as flavor, fragrance and essential oils in electrospun polymer-free CD-IC NFs may have potential for food related applications by integrating the particularly large surface area of NFs with the non-toxic nature of CD and inclusion complexation benefits, such as high temperature stability, improved water solubility and an enhanced

Polyolefin nanocomposites in situ polymerization

Energy Technology Data Exchange (ETDEWEB)

Galland, Griselda Barrera; Fim, Fabiana de C.; Milani, Marceo A.; Silva, Silene P. da; Forest, Tadeu; Radaelli, Gislaine, E-mail: griselda.barrera@ufrgs.br [Universidade Federal do Rio Grande de Sul - UFRGS, Porto Alegre, RS (Brazil); Basso, Nara R.S. [Pontificia Universidade Catolica do Rio Grande do Sul, Porto Alegre, RS (Brazil); Quijada, Raul [Universidad de Chile, Santiago (Chile)

2011-07-01

Polyethylene and polypropylene nanocomposites using grapheme nanosheets and treated chrysotile have been synthesized by in situ polymerization using metallocene catalysts. The fillers have been submitted to acid, thermal and/ou ultrasound treatments before to introduce them into the polymerization reactor. A complete characterization of the fillers has been done. The nanocomposites have been characterized by SEM, TEM, DRX and AFM. The thermal, mechanic -dynamic, mechanical and electrical properties of the nanocomposites are discussed. (author)

Polyolefin nanocomposites in situ polymerization

International Nuclear Information System (INIS)

Galland, Griselda Barrera; Fim, Fabiana de C.; Milani, Marceo A.; Silva, Silene P. da; Forest, Tadeu; Radaelli, Gislaine; Basso, Nara R.S.; Quijada, Raul

2011-01-01

Polyethylene and polypropylene nanocomposites using grapheme nanosheets and treated chrysotile have been synthesized by in situ polymerization using metallocene catalysts. The fillers have been submitted to acid, thermal and/ou ultrasound treatments before to introduce them into the polymerization reactor. A complete characterization of the fillers has been done. The nanocomposites have been characterized by SEM, TEM, DRX and AFM. The thermal, mechanic -dynamic, mechanical and electrical properties of the nanocomposites are discussed. (author)

On-demand photoinitiated polymerization

Science.gov (United States)

Boydston, Andrew J; Grubbs, Robert H; Daeffler, Chris; Momcilovic, Nebojsa

2013-12-10

Compositions and methods for adjustable lenses are provided. In some embodiments, the lenses contain a lens matrix material, a masking compound, and a prepolymer. The lens matrix material provides structure to the lens. The masking compound is capable of blocking polymerization or crosslinking of the prepolymer, until photoisomerization of the compound is triggered, and the compound is converted from a first isomer to a second isomer having a different absorption profile. The prepolymer is a composition that can undergo a polymerization or crosslinking reaction upon photoinitiation to alter one or more of the properties of the lenses.

Studies on the polymerization of acrolein oxime, 6

International Nuclear Information System (INIS)

Masuda, Seizo; Tamai, Harumi; Ota, Tadatoshi; Torii, Munetomo; Tanaka, Masami.

1979-01-01

Radiation-induced polymerization and copolymerization of acrolein oxime are investigated in different solvents and at a wide range of temperature for obtaining information on the reaction mechanism. Acrolein oxime is polymerized ionically, irrespective of dryness of the sample. Arrhenius plots for the polymerization rate, which do not yield a linear relation, can be adequately approximated by two straight lines. An anionic mechanism is operative above the room temperature, while a cationic mechanism predominates below -23 0 C. The reaction in the intermediate temperature range proceeds by a competitive mechanism, and the rate of the anionic and cationic polymerizations becomes equal at the temperature near -5 0 C. The reaction rate is proportional to the square root of dose rate at room temperature and -23 0 C. On the basis of these data, it is proposed that the polymerization of acrolein oxime by γ-irradiation proceeds by free-ionic mechanisms. (author)

Fluoropolymer materials and architectures prepared by controlled radical polymerizations

DEFF Research Database (Denmark)

Hansen, Natanya Majbritt Louie; Jankova Atanasova, Katja; Hvilsted, Søren

2007-01-01

This review initially summarizes the mechanisms, merits and limitations of the three controlled radical polymerizations: nitroxide mediated polymerization (NMP), atom transfer radical polymerization (ATRP) or metal catalyzed living radical polymerization, and reversible addition–fragmentation chain...... transfer (RAFT) polymerization. This is followed by two parts, one dealing with homo- and copolymerizations of fluorinated methacrylates and acrylates, and a second where fluorinated styrenes, alone or in combination with other monomers, are the main issues. In these parts, initiators (including...... properties and functionalities that can be obtained from these novel fluorinated materials and architectures are especially emphasized. Thus, various amphiphilic, biocompatible or low energy materials, fluorinated nanoparticles and nanoporous films/membranes as well as materials for submicron and nanolevel...

Online observation of emulsion polymerization by fluorescence technique

CERN Document Server

Rudschuck, S; Fuhrmann, J

1999-01-01

An online observation of local polarity via fluorescence spectroscopy was used to study the formation and growth of polymer particles during an emulsifier-free heterogeneous polymerization. The reaction mixture consisted of styrene dispersed in water and the polymerization was initiated by a macro-initiator (hydrolyzed propene-maleic acid copolymer with t-butyl perester groups). Pyrenyl probes were attached to the backbone of the initiator to analyze the heterogeneous reaction. The experimental results allow a clear distinction of different time regions during the heterogeneous polymerization. Information about the heating period, the latex formation, the particle growth and the final stage of the polymerization process (gel point) were obtained. (11 refs).

Vinyl acetate polymerization by ionizing radiation

International Nuclear Information System (INIS)

Mesquita, Andrea Cercan

2002-01-01

The aim of this work is the synthesis and characterization of the poly(vinyl acetate) using the ionizing radiation. Six polymerizations of vinyl acetate were carried out using three techniques of polymerization: in bulk, emulsion and solution. In the technique of solution polymerization were used two solvents, the alcohol ethyl and the methylethylketone, in two proportions 1:0.5 and 1:1 related to the monomer. The solutions were irradiated with gamma rays from a 60 Co source, with dose rate between 5.25 kGy/h and 6.26 kGy/h. The polymers obtained were characterized by Fourier Transform Infrared Spectroscopy (FTIR). The glass transition temperature (Tg) was investigated by Differential Scanning Calorimeter (DSC). The molecular weight was analyzed by the technique of Gel Permeation Chromatography (GPC). Tests of density, hardness and Vicat softening temperature were carried out. The infrared spectroscopy and others results confirmed that the polymers obtained by polymerization of vinyl acetate in bulk, emulsion and solution, using ionizing radiation, really correspond at poly(vinyl acetate). (author)

The optimal dose reduction level using iterative reconstruction with prospective ECG-triggered coronary CTA using 256-slice MDCT

International Nuclear Information System (INIS)

Hou, Yang; Xu, Shu; Guo, Wenli; Vembar, Mani; Guo, Qiyong

2012-01-01

Aim: To assess the image quality (IQ) of an iterative reconstruction (IR) technique (iDose 4 ) from prospective electrocardiography (ECG)-triggered coronary computed tomography angiography (coronary CTA) on a 256-slice multi-detector CT (MDCT) scanner and determine the optimal dose reduction using IR that can provide IQ comparable to filtered back projection (FBP). Method and materials: 110 consecutive patients (69 men, 41 women; age: 54 ± 10 years) underwent coronary CTA on a 256-slice MDCT (Brilliance iCT, Philips Healthcare). The control group (Group A, n = 21) were scanned using the conventional tube output (120 kVp, 210 mAs) and reconstructed using FBP. The other 4 groups were scanned with the same kVp but successively reduced tube output as follows: B[n = 15]: 125 mAs; C[n = 22]: 105 mAs; D[n = 36]: 84 mAs: E[n = 16]: 65 mAs) and reconstructed using IR levels of L3 (Group B), L4 (Group C) and L5 (Groups D and E), to compensate for the noise increase. All images were reconstructed using the same kernel (XCB). Two radiologists graded IQ in a blinded fashion on a 4-point scale (4 – excellent, 3 – good, 2 – fair and 1 – poor). Quantitative measurements of CT values, image noise and contrast-to-noise (CNR) were measured in each group. A receiver-operating characteristic (ROC) analysis was performed to determine a radiation reduction threshold up to which excellent IQ was maintained. Results: There were no significant differences in objective noise, SNR and CNR values among Groups A, B, C, D, and E (P = 0.14, 0.09, 0.17, respectively). There were no significant differences in the scores of the subjective IQ between Group A, and Groups B, C, D, E (P = 0.23–0.97). Significant differences in image sharpness and study acceptability were observed between groups A and E (P < 0.05). Using the criterion of excellent IQ (score 4), the ROC curve of dose levels and IQ acceptability established a reduction of 60% of tube output (Group D) as optimum cutoff point (AUC

Supramolecular polymeric materials via cyclodextrin-guest interactions.

Science.gov (United States)

Harada, Akira; Takashima, Yoshinori; Nakahata, Masaki

2014-07-15

CONSPECTUS: Cyclodextrins (CDs) have many attractive functions, including molecular recognition, hydrolysis, catalysis, and polymerization. One of the most important uses of CDs is for the molecular recognition of hydrophobic organic guest molecules in aqueous solutions. CDs are desirable host molecules because they are environmentally benign and offer diverse functions. This Account demonstrates some of the great advances in the development of supramolecular materials through host-guest interactions within the last 10 years. In 1990, we developed topological supramolecular complexes with CDs, polyrotaxane, and CD tubes, and these preparation methods take advantage of self-organization between the CDs and the polymers. The combination of polyrotaxane with αCD forms a hydrogel through the interaction of αCDs with the OH groups on poly(ethylene glycol). We categorized these polyrotaxane chemistries within main chain type complexes. At the same time, we studied the interactions of side chain type supramolecular complexes with CDs. In these systems the guest molecules modified the polymers and selectively formed inclusion complexes with CDs. The systems that used low molecular weight compounds did not show such selectivity with CDs. The multivalency available within the complex cooperatively enhances the selective binding of CD with guest molecules via the polymer side chains, a phenomenon that is analogous to binding patterns observed in antigen-antibody complexes. To incorporate the molecular recognition properties of CDs within the polymer side chains, we first prepared stimuli-responsive sol-gel switching materials through host-guest interactions. We chose azobenzene derivatives for their response to light and ferrocene derivatives for their response to redox conditions. The supramolecular materials were both redox-responsive and self-healing, and these properties resulted from host-guest interactions. These sol-gels with built in switches gave us insight for

A comparison of three dimensional change in maxillary complete dentures between conventional heat polymerizing and microwave polymerizing techniques

Directory of Open Access Journals (Sweden)

Shinsuke Sadamori

2007-03-01

Full Text Available The purpose of this study was to measure and compare two different polymerizing processes, heat polymerizing (HP and microwave polymerizing (MP, on the three dimensional changes in the fitting surface and artificial teeth of maxillary complete dentures. A threedimensional coordinate measurement system was used to record distortion of the specimens. The distortion of the fitting surface was measured from the reference plane on the fitting side from which a coordinate system was set, and the movement of the artificial teeth and the distortion of the polished surface was measured from the reference plane of the artificial tooth side, from which a coordinate system was set. It was clearly showed that various distortions of denture specimens after polymerization process can be measured with this three-coordinate measuring machine. The study showed that the overall distortion of the fitting surface in HP specimens was shown to be larger than in MP ones.

Study on irradiated polymerization of acrylonitrile by NMR

International Nuclear Information System (INIS)

Zhao Xin; Lin Hao

1999-01-01

Sup 13 C CP/MAS spectra and nuclear Overhauser effects (NOE) at room temperature have been measured for acrylonitrile (AN) in homophase irradiated polymerization. With the increase of radiation dose the chemical shift of cracking peaks and NOE are variation. This implies that the polymerized mechanism of AN were changed with the variation of irradiated doses and dose rate. There is the stronger affinity electron group (-CN) in acrylonitrile monomer. It may be polymerized by various ways and mechanism and be gained the polymer of difference structures and molecular weight of polyacrylonitrile (PAN). Starmicarbon and Starker obtained higher molecular weight of polyacrylonitrile by peroxysulfate-pyrosulfite in oxidation-reduction system. The superhigh molecular weight of PAN was synthesized chemically according to the method of Wu et. al. by suspension polymerization. In this paper we discussed that the relative concentrations of steric dyads and triads in the chain structure in PAN and the irradiation polymerized mechanism of acrylonitrile monomer in room temperature by different dose and dose rate

Factors affecting toxicity and efficacy of polymeric nanomedicines

International Nuclear Information System (INIS)

Igarashi, Eiki

2008-01-01

Nanomedicine is the application of nanotechnology to medicine. The purpose of this article is to review common characteristics of polymeric nanomedicines with respect to passive targeting. We consider several biodegradable polymeric nanomedicines that are between 1 and 100 nm in size, and discuss the impact of this technology on efficacy, pharmacokinetics, toxicity and targeting. The degree of toxicity of polymeric nanomedicines is strongly influenced by the biological conditions of the local environment, which influence the rate of degradation or release of polymeric nanomedicines. The dissemination of polymeric nanomedicines in vivo depends on the capillary network, which can provide differential access to normal and tumor cells. The accumulation of nanomedicines in the microlymphatics depends upon retention time in the blood and extracellular compartments, as well as the type of capillary endothelium surrounding specific tissues. Finally, the toxicity or efficacy of intact nanomedicines is also dependent upon tissue type, i.e., non-endocrine or endocrine tissue, spleen, or lymphatics, as well as tumor type

Preparation and certification of the Polish reference material 'Oriental Tobacco Leaves' (CTA-OTL-1) for inorganic trace analysis

International Nuclear Information System (INIS)

Dybczynski, R.; Polkowska-Motrenko, H.; Samczynski, Z.; Szopa, Z.

1996-01-01

A new Polish certified reference material 'Oriental Tobacco Leaves' (CTA-OTL-1) for inorganic trace analysis was prepared. Fresh tobacco leaves of variety 'Oriental' were dried, ground and sieved. All precautions were taken to avoid contamination of material with metals. The next step was homogenization. Preliminary homogeneity checking consisted in determining of Ca, Fe and K content by X-ray fluorescence. Final homogeneity testing was performed by neutron activation analysis determining Co, Cr, Fe and Rb. To assure long-term stability, the whole lot of material was sterilized by electron beam radiation. Certification of the candidate reference material was done on the basis of world-wide interlaboratory comparisons exercise in which 61 laboratories, using various analytical methods participated. (author). 30 refs, 12 tabs, 21 figs

Preparation and certification of the Polish reference material `Oriental Tobacco Leaves` (CTA-OTL-1) for inorganic trace analysis

Energy Technology Data Exchange (ETDEWEB)

Dybczynski, R.; Polkowska-Motrenko, H.; Samczynski, Z.; Szopa, Z. [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

1996-12-31

A new Polish certified reference material `Oriental Tobacco Leaves` (CTA-OTL-1) for inorganic trace analysis was prepared. Fresh tobacco leaves of variety `Oriental` were dried, ground and sieved. All precautions were taken to avoid contamination of material with metals. The next step was homogenization. Preliminary homogeneity checking consisted in determining of Ca, Fe and K content by X-ray fluorescence. Final homogeneity testing was performed by neutron activation analysis determining Co, Cr, Fe and Rb. To assure long-term stability, the whole lot of material was sterilized by electron beam radiation. Certification of the candidate reference material was done on the basis of world-wide interlaboratory comparisons exercise in which 61 laboratories, using various analytical methods participated. (author). 30 refs, 12 tabs, 21 figs.

El gobierno corporativo en la cooperativa de trabajo asociado Recuperar CTA

Directory of Open Access Journals (Sweden)

Carlos Mario Toro Orozco

2012-01-01

Full Text Available En la cooperativa de trabajo asociado Recuperar (CTA se ha logrado demostrar, a través de esta investigación, la efectividad de la concertación entre el gobierno corporativo y la vinculación de los asociados a la solución eficaz y eficiente de un problema social prioritario para una ciudad, como ha sido el reciclaje de las basuras. Es por ello que en este artículo se evidencia cómo, a partir del Gobierno Corporativo , esta organización ha logrado una proyección económica y social que le ha permitido cumplir las necesidades de los asociados, estableciendo una cultura gerencial y de resultados, por medio de lo cual se ha logrado la permanencia de dicha organización en el sector solidario, como un ejemplo de gestión y proyección social. La metodología utilizada es un estudio de corte cualitativo a partir del análisis de los diferentes aspectos para establecer los mecanismos de Gobierno Corporativo. Los resultados permiten observar que su crecimiento y permanencia en el tiempo se ha obtenido, a través de la coherencia con los valores cooperativos, la igualdad y la solidaridad con las exigencias del mercado; la participación y el control democrático; de igual forma la identidad, autonomía e independencia por parte de sus asociados.

Polymeric bicontinuous microemulsions

DEFF Research Database (Denmark)

Bates, F.S.; Maurer, W.W.; Lipic, P.M.

1997-01-01

High molecular weight block copolymers can be viewed as macromolecular surfactants when blended with thermodynamically incompatible homopolymers. This Letter describes the formation of polymeric bicontinuous microemulsions in nurtures containing a model diblock copolymer and two homopolymers. Alt...

Polymeric Coatings for Combating Biocorrosion

Science.gov (United States)

Guo, Jing; Yuan, Shaojun; Jiang, Wei; Lv, Li; Liang, Bin; Pehkonen, Simo O.

2018-03-01

Biocorrosion has been considered as big trouble in many industries and marine environments due to causing great economic loss. The main disadvantages of present approaches to prevent corrosion include being limited by environmental factors, being expensive, inapplicable to field, and sometimes inefficient. Studies show that polymer coatings with anti-corrosion and anti-microbial properties have been widely accepted as a novel and effective approach to preventbiocorrosion. The main purpose of this review is to summarize up the progressive status of polymer coatings used for combating microbially-induced corrosion. Polymers used to synthesize protective coatings are generally divided into three categories: i) traditional polymers incorporated with biocides, ii) antibacterial polymers containing quaternary ammonium compounds, and iii) conductive polymers. The strategies to synthesize polymer coatings resort mainly to grafting anti-bacterial polymers from the metal substrate surface using novel surface-functionalization approaches, such as free radical polymerization, chemically oxidative polymerization and surface-initiated atom transfer radical polymerization, as opposed to the traditional approaches of dip coating or spin coating.

Olefin metathesis and metathesis polymerization

CERN Document Server

Ivin, K J

1997-01-01

This book is a follow-up to Ivins Olefin Metathesis, (Academic Press, 1983). Bringing the standard text in the field up to date, this Second Edition is a result of rapid growth in the field, sparked by the discovery of numerous well-defined metal carbene complexes that can act as very efficient initiators of all types of olefin metathesis reaction, including ring-closing metathesis of acyclic dienes, enynes, and dienynes; ring-opening metathesis polymerizationof cycloalkenes, acyclic diene metathesis polymerization; and polymerization of alkynes, as well as simple olefin metathesis. Olefin Metathesis and Metathesis Polymerization provides a broad, up-to-date account of the subject from its beginnings in 1957 to the latest applications in organic synthesis. The book follows the same format as the original, making it useful toteachers and to researchers, and will be of particular interest to those working in the fields of organic chemistry, polymer chemistry, organometallic chemistry, catalysis, materials scien...

Optical Fiber Sensors Based on Polymeric Sensitive Coatings

Directory of Open Access Journals (Sweden)

Pedro J. Rivero

2018-03-01

Full Text Available Polymer technology is one of the fastest growing fields of contemporary research due to the possibility of using a wide variety of synthetic chemical routes for obtaining a polymeric network with a well-defined structure, resulting in materials with outstanding macroscopic properties. Surface engineering techniques based on the implementation of polymeric structures can be used as an interesting tool for the design of materials with functional properties. In this sense, the use of fabrication techniques for the design of nanostructured polymeric coatings is showing an important growth due to the intrinsic advantages of controlling the structure at a nanoscale level because physical, chemical, or optical properties can be considerably improved in comparison with the bulk materials. In addition, the presence of these sensitive polymeric coatings on optical fiber is a hot topic in the scientific community for its implementation in different market niches because a wide variety of parameters can be perfectly measured with a high selectivity, sensitivity, and fast response time. In this work, the two main roles that a polymeric sensitive matrix can play on an optical fiber for sensing applications are evaluated. In a first section, the polymers are used as a solid support for the immobilization of specific sensitive element, whereas in the second section the polymeric matrix is used as the chemical transducer itself. Additionally, potential applications of the optical fiber sensors in fields as diverse as biology, chemistry, engineering, environmental, industry or medicine will be presented in concordance with these two main roles of the polymeric sensitive matrices.

Polymeric implant of methylprednisolone for spinal injury ...

African Journals Online (AJOL)

Polymeric implant of methylprednisolone for spinal injury: preparation and characterization. Bo Yin, Jian-Jun Ji, Ming Yang. Abstract. Purpose: To improve the effectiveness and reduce the systemic side effects of methylprednisolone in traumatic spinal injuries, its polymeric implants were prepared using chitosan and sodium ...

Initiation of MMA polymerization by iniferters based on dithiocarbamates

Directory of Open Access Journals (Sweden)

Jovanović Slobodan M.

2005-01-01

Full Text Available Twelve modified dithiocarbamates and a thiuramdisulfide used for the initiation of methyl methacrylate (MMA polymerization were synthesized in this study. The polymerization of MMA was followed by determine the yield and molar mass of the obtained PMMA as a function of polymerization time. Four of the synthesized dithiocarbamates S-benzyl-N,N-dibenzyldithiocarbamate, S-allyl-N,N-dibenzyldithiocarbamate S-benzyl-N,N-diisobutyldithiocarbamate and S-benzoyl-N,N-diisobutyldithiocarbamate, as well as N,N,N',N'-tetrabenzylthiuramdisulfide acted as iniferters. They were active as the initiators of the photo and/or thermally initiated radical polymerization of MMA in bulk and inert solvents (benzene and toluene. S Benzyl - N,N - dibenzyldithiocarbamate can be successfully used for the initiation of MMA polymerization in a polar solvent such as dimethylacetamide.

Template-Directed Fabrication of Anatase TiO2 Hollow Nanoparticles and Their Application in Photocatalytic Degradation of Methyl Orange

Institute of Scientific and Technical Information of China (English)

Jie Chang; Wenjian Zhang; Chunyan Hong

2017-01-01

Polymerization-induced self-assembly (PISA) was used to fabricate polymeric nanoparticles via reversible addition-fragmentation chain transfer (RAFT) dispersion polymerization of benzyl methacrylate (BzMA) using diblock copolymer poly(glycerol monomethacrylate)-block-poly(2-dimethylaminoethyl methacrylate) (PGMMA-PDMAEMA-CTA) as the macro RAFT agent.The dispersion of polymeric nanoparticles with a final concentration of about 210 mg/g (solid content of 21％) was obtained via this efficient method (PISA).The resultant polymeric nanoparticles consisting of corona-shell-core three layers with weak polyelectrolyte PDMAEMA as the shell were used as sacrificial template to fabricate TiO2 hollow nanoparticles.The negatively charged titanium precursor was absorbed into the PDMAEMA shell via the electrostatic interaction,and hydrolyzed to form polymer/TiO2 hybrid nanoparticles.Anatase TiO2 hollow nanoparticles were formed after removing the polymeric templates by calcination at 550 ℃.The experiments of photocatalytic degradation of methyl orange showed that the resultant anatase TiO2 hollow nanoparticles had high photocatalytic activity and good reusability.

Electrochemical Characterization of a Polymer Inclusion Membrane Made of Cellulose Triacetate and Aliquat 336 and Its Application to Sulfonamides Separation

Directory of Open Access Journals (Sweden)

Juana Benavente

2018-01-01

Full Text Available An electrochemical characterization of a polymer inclusion membrane (PIM fabricated with the ionic liquid (IL Aliquat 336 (26% and the polymer cellulose triacetate (CTA (76% is presented. Considering the use of PIMs in separation systems to remove pollutants from water, the characterization was performed with NaCl solutions by measuring membrane potential, electrochemical impedance spectroscopy, and salt diffusion and results were compared with those obtained from dry membranes. Results showed a significant reduction in the membrane diffusive permeability and electrical conductivity as well as the transport number of cation Na+ across the PIM when compared with solution values, which could be mainly related to the dense character of the membrane. Membrane application in the separation of different sulfonamides (sulfathiazole, sulfapyridine, sulfamethazine, and sulfamethoxazole from water, with 1 M NaCl solution as striping phase, was also considered. These results indicated that the different chemical characteristics of the compounds, as well as the compact structure of the PIM, limited the transport of the organic molecules though it.

Pentafluorosulfanyl Substituents in Polymerization Catalysis.

Science.gov (United States)

Kenyon, Philip; Mecking, Stefan

2017-10-04

Highly electron-withdrawing pentafluorosulfanyl groups were probed as substituents in an organometallic catalyst. In Ni(II) salicylaldiminato complexes as an example case, these highly electron-withdrawing substituents allow for polymerization of ethylene to higher molecular weights with reduced branching due to significant reductions in β-hydrogen elimination. Combined with the excellent functional group tolerance of neutral Ni(II) complexes, this suppression of β-hydrogen elimination allows for the direct polymerization of ethylene in water to nanocrystal dispersions of disentangled, ultrahigh-molecular-weight linear polyethylene.

Scale-up of microwave-assisted polymerizations in continuous-flow mode : cationic ring-opening polymerization of 2-ethyl-2-oxazoline

NARCIS (Netherlands)

Paulus, R.M.; Erdmenger, T.; Becer, C.R.; Hoogenboom, R.; Schubert, U.S.

2007-01-01

Microwave-assisted polymerizations is a growing field of interest because the use of microwave irradiation instead of thermal heating was demonstrated to result in faster, cleaner, and higher yielding reactions. To overcome the one-at-a-time nature of preparing polymerizations in single microwave

Silicon dioxide obtained by Polymeric Precursor Method

International Nuclear Information System (INIS)

Oliveira, C.T.; Granado, S.R.; Lopes, S.A.; Cavalheiro, A.A.

2011-01-01

The Polymeric Precursor Method is able for obtaining several oxide material types with high surface area even obtained in particle form. Several MO 2 oxide types such as titanium, silicon and zirconium ones can be obtained by this methodology. In this work, the synthesis of silicon oxide was monitored by thermal analysis, XRD and surface area analysis in order to demonstrate the influence of the several synthesis and calcining parameters. Surface area values as higher as 370m2/g and increasing in the micropore volume nm were obtained when the material was synthesized by using ethylene glycol as polymerizing agent. XRD analysis showed that the material is amorphous when calcinated at 600°C in despite of the time of calcining, but the material morphology is strongly influenced by the polymeric resin composition. Using Glycerol as polymerizing agent, the pore size increase and the surface area goes down with the increasing in decomposition time, when compared to ethylene glycol. (author)

Biomimetic polymeric membranes for water treatment

DEFF Research Database (Denmark)

Habel, Joachim Erich Otto

This project is about the interplay of the three major components of aquaporin based biomimetic polymeric membranes (ABPMs): Aquaporins (AQPs), amphiphilic block copolymers, serving as a vesicular matrix for the hydrophobic AQP exterior (proteopolymersomes) and a polymeric membrane as embedment....... The interplay of proteopolymersomes and polymeric mesh support (in this case polyethersulfone, PES) was examined via integration of proteopolymersomes in an active layer (AL) formed by interfacial polymerisation between a linker molecule in aqueous phase and another in organic phase on top of the PES....... The resulting thin-film composite (TFC) membrane was analyzed via cross-flow forward osmosis (FO), scanning electron microscopy (SEM), fourier-transformed infrared spectroscopy (FTIR), as well as in the non-supported form over FTIR and a specialized microfluidic visualization approach. Where no clear dierences...

Radiation-induced polymerization of glass-forming systems. VII. Polymerization in supercooled state under high pressure

International Nuclear Information System (INIS)

Kaetsu, I.; Yoshii, F.; Watanabe, Y.

1978-01-01

Radiation-induced polymerization of glass-forming monomers such as 2-hydroxyethyl methacrylate and glycidyl methacrylate under high pressure was studied. The glass transition temperature of these monomers was heightened by increased pressure. The temperature dependence of polymerizability showed a characteristic relation, similar to those in supercooled-phase polymerization under normal pressure, that had a maximum at T/sub ν/ which shifted to higher levels of temperature as well as to T/sub g/ under high pressure. Polymerizability in the supercooled state also increased under increased pressure

Monte Carlo simulation of non-linear free radical polymerization using a percolation kinetic gelation model (I): free radical homo polymerization

International Nuclear Information System (INIS)

Ghiass, M.; Dabir, B.; Nikazar, M.; Rey, A.D.; Mirzadeh, H.

2001-01-01

A kinetic gelation model that incorporates the kinetics of free radical homo polymerization is implemented to determine the effects of kinetics on polymerization statistics and microstructures. The simulation is performed on a simple cubic lattice that has 100 sites in each direction. A new algorithm for random selecting of the next step in a self-avoiding random walk and very efficient mechanisms of mobility of components are introduced to improve the generality of the predictions by removing commonly accruing deficiencies due to early trapping of radicals. A first order kinetics is considered for decomposition of initiator that enables us to consider the effect of temperature on polymerization reaction. Better understanding of microstructural evolution during polymerization and providing a framework to produce a realistic system of highly packed random chains within polymer network are among the benefits of model

Approaching Inclusion as Social Practice: Processes of Inclusion and Exclusion

DEFF Research Database (Denmark)

Molbæk, Mette; Hansen, Janne Hedegaard; Lassen, Mikkel

2018-01-01

The article presents the results of a review of international research investigating mechanisms and processes of inclusion and exclusion as an ongoing part of social practice in a school context. The review forms part of a research project investigating the social practices of inclusive education...... in primary and lower-secondary education (age 6–16) in public schools as constituted by processes of inclusion and exclusion. The project aims to shift the scientific focus of research in inclusive education from the development of pedagogical and didactic practice to the importance of community construction...... through inclusion and exclusion processes. The project arises in context of Danish education policy, while the review looked for international research findings on the limits between inclusion and exclusion: how they are drawn, by whom, for what reasons, and for whose benefit? On the background...

A model of frontal polymerization using complex initiation

Directory of Open Access Journals (Sweden)

P. M. Goldfeder

1999-01-01

Full Text Available Frontal polymerization is a process in which a spatially localized reaction zone propagates into a monomer, converting it into a polymer. In the simplest case of free-radical polymerization, a mixture of monomer and initiator is placed in a test tube. A reaction is then initiated at one end of the tube. Over time, a self-sustained thermal wave, in which chemical conversion occurs, is produced. This phenomenon is possible because of the highly exothermic nature of the polymerization reactions.

Limits to Inclusion

Science.gov (United States)

Hansen, Janne Hedegaard

2012-01-01

In this article, I will argue that a theoretical identification of the limit to inclusion is needed in the conceptual identification of inclusion. On the one hand, inclusion is formulated as a vision that is, in principle, limitless. On the other hand, there seems to be an agreement that inclusion has a limit in the pedagogical practice. However,…

Post polymerization cure shape memory polymers

Energy Technology Data Exchange (ETDEWEB)

Wilson, Thomas S.; Hearon, II, Michael Keith; Bearinger, Jane P.

2017-01-10

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

Post polymerization cure shape memory polymers

Science.gov (United States)

Wilson, Thomas S; Hearon, Michael Keith; Bearinger, Jane P

2014-11-11

This invention relates to chemical polymer compositions, methods of synthesis, and fabrication methods for devices regarding polymers capable of displaying shape memory behavior (SMPs) and which can first be polymerized to a linear or branched polymeric structure, having thermoplastic properties, subsequently processed into a device through processes typical of polymer melts, solutions, and dispersions and then crossed linked to a shape memory thermoset polymer retaining the processed shape.

Simulating Controlled Radical Polymerizations with mcPolymer—A Monte Carlo Approach

Directory of Open Access Journals (Sweden)

Georg Drache

2012-07-01

Full Text Available Utilizing model calculations may lead to a better understanding of the complex kinetics of the controlled radical polymerization. We developed a universal simulation tool (mcPolymer, which is based on the widely used Monte Carlo simulation technique. This article focuses on the software architecture of the program, including its data management and optimization approaches. We were able to simulate polymer chains as individual objects, allowing us to gain more detailed microstructural information of the polymeric products. For all given examples of controlled radical polymerization (nitroxide mediated radical polymerization (NMRP homo- and copolymerization, atom transfer radical polymerization (ATRP, reversible addition fragmentation chain transfer polymerization (RAFT, we present detailed performance analyses demonstrating the influence of the system size, concentrations of reactants, and the peculiarities of data. Different possibilities were exemplarily illustrated for finding an adequate balance between precision, memory consumption, and computation time of the simulation. Due to its flexible software architecture, the application of mcPolymer is not limited to the controlled radical polymerization, but can be adjusted in a straightforward manner to further polymerization models.

Non-equilibrium supramolecular polymerization.

Science.gov (United States)

Sorrenti, Alessandro; Leira-Iglesias, Jorge; Markvoort, Albert J; de Greef, Tom F A; Hermans, Thomas M

2017-09-18

Supramolecular polymerization has been traditionally focused on the thermodynamic equilibrium state, where one-dimensional assemblies reside at the global minimum of the Gibbs free energy. The pathway and rate to reach the equilibrium state are irrelevant, and the resulting assemblies remain unchanged over time. In the past decade, the focus has shifted to kinetically trapped (non-dissipative non-equilibrium) structures that heavily depend on the method of preparation (i.e., pathway complexity), and where the assembly rates are of key importance. Kinetic models have greatly improved our understanding of competing pathways, and shown how to steer supramolecular polymerization in the desired direction (i.e., pathway selection). The most recent innovation in the field relies on energy or mass input that is dissipated to keep the system away from the thermodynamic equilibrium (or from other non-dissipative states). This tutorial review aims to provide the reader with a set of tools to identify different types of self-assembled states that have been explored so far. In particular, we aim to clarify the often unclear use of the term "non-equilibrium self-assembly" by subdividing systems into dissipative, and non-dissipative non-equilibrium states. Examples are given for each of the states, with a focus on non-dissipative non-equilibrium states found in one-dimensional supramolecular polymerization.

On reactions of polymerization of p-element hydroxides in aqueous solutions

International Nuclear Information System (INIS)

Tikavyj, V.F.; Lesnikovich, A.I.

1978-01-01

The tendency of p-element hydroxides towards polymerization in aqueous solutions has been considered with respect to their location in the Periodic Table. Stable hydroxides of d-elements are practically all polymerized; among s-elements only berillium and magnesium hydroxides polymerize as the least dissociated ones. Hydroxides of the elements located to the right of the 4 Group and above the 5-th Period do not polymerize in aqueous solutions. The structure and tendency towards polymerization of In, Te, and I compounds have been studied. The tendency to polymerization of all hydroxides of p-elements located below the 4-th Period is explained from the standpoint of electron structure and the simplest thermodynamic analysis (entropy, enthalpy)

Fabrication and manipulation of polymeric magnetic particles with magnetorheological fluid

International Nuclear Information System (INIS)

Rodríguez-López, Jaime; Shum, Ho Cheung; Elvira, Luis; Montero de Espinosa, Francisco; Weitz, David A.

2013-01-01

Polymeric magnetic microparticles have been created using a microfluidic device via ultraviolet (UV) polymerization of double emulsions, resulting in cores of magnetorheological (MR) fluids surrounded by polymeric shells. We demonstrate that the resultant particles can be manipulated magnetically to achieve triggered rupture of the capsules. This illustrates the great potential of our capsules for triggered release of active ingredients encapsulated in the polymeric magnetic microparticles. - Highlights: ► Polymeric microparticles encapsulating MR fluids have been fabricated. ► A double-emulsion-templated approach using microfluidic techniques has been used. ► The monodisperse microparticles obtained are easily manipulated under magnetic field. ► These microparticles have great potential for encapsulation-and-release applications.

Inclusive Business - What It Is All About? Managing Inclusive Companies

Directory of Open Access Journals (Sweden)

Tea Golja

2012-01-01

Full Text Available Following the challenges we face today, the inclusive business models are future business models through which the Millennium Development Goals can be fostered and strengthen. These are the models which, through their strategic orientation on inclusivity, include low income communities in their value chain. This can be done through combining variety of strategies which all have two common points – recognition of stakeholders and adjustment of the product to the target market. The paper presents the analysis of inclusive markets. Hence, the research results show the dispersion of inclusive businesses worldwide, type of the organization, sector coverage, and contribution to MDGs as well as the particular way of inclusion of low income communities in their value chain. The aim is to present how inclusive business benefits not only the low income societies, but the companies that operate in this way as well.

Self-assembled polymeric nanocarriers for the targeted delivery of retinoic acid to the hair follicle

Science.gov (United States)

Lapteva, Maria; Möller, Michael; Gurny, Robert; Kalia, Yogeshvar N.

2015-11-01

Acne vulgaris is a highly prevalent dermatological disease of the pilosebaceous unit (PSU). An inability to target drug delivery to the PSU results in poor treatment efficacy and the incidence of local side-effects. Cutaneous application of nanoparticulate systems is reported to induce preferential accumulation in appendageal structures. The aim of this work was to prepare stable polymeric micelles containing retinoic acid (RA) using a biodegradable and biocompatible diblock methoxy-poly(ethylene glycol)-poly(hexylsubstituted lactic acid) copolymer (MPEG-dihexPLA) and to evaluate their ability to deliver RA to skin. An innovative punch biopsy sample preparation method was developed to selectively quantify follicular delivery; the amounts of RA present were compared to those in bulk skin, (i.e. without PSU), which served as the control. RA was successfully incorporated into micelle nanocarriers and protected from photoisomerization by inclusion of Quinoline Yellow. Incorporation into the spherical, homogeneous and nanometer-scale micelles (dn 400-fold. Drug delivery experiments in vitro showed that micelles were able to deliver RA to porcine and human skins more efficiently than Retin-A® Micro (0.04%), a marketed gel containing RA loaded microspheres, (7.1 +/- 1.1% vs. 0.4 +/- 0.1% and 7.5 +/- 0.8% vs. 0.8 +/- 0.1% of the applied dose, respectively). In contrast to a non-colloidal RA solution, Effederm® (0.05%), both the RA loaded MPEG-dihexPLA polymeric micelles (0.005%) and Retin-A® Micro (0.04%) displayed selectivity for delivery to the PSU with 2-fold higher delivery to PSU containing samples than to control samples. Moreover, the micelle formulation outperformed Retin-A® Micro in terms of delivery efficiency to PSU presenting human skin (10.4 +/- 3.2% vs. 0.6 +/- 0.2%, respectively). The results indicate that the polymeric micelle formulation enabled an increased and targeted delivery of RA to the PSU, potentially translating to a safer and more efficient

Comparison of techniques for the determination of conversion during suspension polymerization reactions

Directory of Open Access Journals (Sweden)

J. C. Santos

2008-06-01

Full Text Available The determination of conversion during suspension polymerization reactions is not an easy task due to the heterogeneity of the reaction medium and the tendency of particles to agglomerate rapidly when stirring is stopped. Usually, bulk polymerization in ampoules is employed to study the kinetics of suspension polymerization reactions. In this work, a comparison of different techniques for the determination of conversion during suspension polymerization reactions is presented. Results showed a good agreement between the conversion obtained by gravimetry during styrene suspension polymerization and on-line conversion monitoring data using fiber-optic based Raman Spectroscopy. Nevertheless, the polymerization rate of styrene bulk polymerization carried out in ampoules was higher than the real reaction rate of styrene suspension polymerization due to slightly higher reaction temperatures. Simulation results using the experimental temperature data in a mathematical model confirmed these results.

Designing Inclusive Systems Designing Inclusion for Real-world Applications

CERN Document Server

Clarkson, John; Robinson, Peter; Lazar, Jonathan; Heylighen, Ann

2012-01-01

The Cambridge Workshops on Universal Access and Assistive Technology (CWUAAT) are a series of workshops held at a Cambridge University College every two years. The workshop theme: “Designing inclusion for real-world applications” refers to the emerging potential and relevance of the latest generations of inclusive design thinking, tools, techniques, and data, to mainstream project applications such as healthcare and the design of working environments. Inclusive Design Research involves developing tools and guidance enabling product designers to design for the widest possible population, for a given range of capabilities. There are five main themes: •Designing for the Real-World •Measuring Demand And Capabilities •Designing Cognitive Interaction with Emerging Technologies •Design for Inclusion •Designing Inclusive Architecture In the tradition of CWUAAT, we have solicited and accepted contributions over a wide range of topics, both within individual themes and also across the workshop’s scope. ...

Simultaneous measurement of polymerization stress and curing kinetics for photo-polymerized composites with high filler contents.

Science.gov (United States)

Wang, Zhengzhi; Landis, Forrest A; Giuseppetti, Anthony A M; Lin-Gibson, Sheng; Chiang, Martin Y M

2014-12-01

Photopolymerized composites are used in a broad range of applications with their performance largely directed by reaction kinetics and contraction accompanying polymerization. The present study was to demonstrate an instrument capable of simultaneously collecting multiple kinetics parameters for a wide range of photopolymerizable systems: degree of conversion (DC), reaction exotherm, and polymerization stress (PS). Our system consisted of a cantilever beam-based instrument (tensometer) that has been optimized to capture a large range of stress generated by lightly-filled to highly-filled composites. The sample configuration allows the tensometer to be coupled to a fast near infrared (NIR) spectrometer collecting spectra in transmission mode. Using our instrument design, simultaneous measurements of PS and DC are performed, for the first time, on a commercial composite with ≈80% (by mass) silica particle fillers. The in situ NIR spectrometer collects more than 10 spectra per second, allowing for thorough characterization of reaction kinetics. With increased instrument sensitivity coupled with the ability to collect real time reaction kinetics information, we show that the external constraint imposed by the cantilever beam during polymerization could affect the rate of cure and final degree of polymerization. The present simultaneous measurement technique is expected to provide new insights into kinetics and property relationships for photopolymerized composites with high filler content such as dental restorative composites. Published by Elsevier Ltd.

Phosphazene-promoted anionic polymerization

KAUST Repository

Zhao, Junpeng; Hadjichristidis, Nikolaos; Gnanou, Yves

2014-01-01

.e. in situ activation (of initiating sites) and polymerization, and summarize the applications of such a mechanism on macromolecular engineering toward functionalized polymers, block copolymers and complex macromolecular architectures.

Polymerization Using Phosphazene Bases

KAUST Repository

Zhao, Junpeng; Hadjichristidis, Nikolaos; Schlaad, Helmut

2015-01-01

. In this chapter, the general features of phosphazenepromoted/catalyzed polymerizations and the applications in macromolecular engineering (synthesis of functionalized polymers, block copolymers, and macromolecular architectures) are discussed with challenges

Very High Energy astronomy from H.E.S.S. to CTA. Opening of a new astronomical window on the non-thermal Universe

International Nuclear Information System (INIS)

Naurois, Mathieu de

2012-01-01

The last ten years saw the emergence of Imaging Atmospheric Cherenkov Telescopes as a mature and efficient technique for the study of the Very High Energy Universe, leading to the successful opening, mainly by the HESS experiment, of our understanding of the non-thermal Universe. This Habilitation thesis summaries ten years of research in Very High Energy gamma-ray astronomy with HESS and CTA. In the first part, instrumental aspects such as the experiment conception, its calibration, the reconstruction of the events and the data analysis are presented. The second parts draws a panorama of the main discoveries in the domain. (author)

Plasma-polymerized alkaline anion-exchange membrane: Synthesis and structure characterization

International Nuclear Information System (INIS)

Hu Jue; Meng Yuedong; Zhang Chengxu; Fang Shidong

2011-01-01

After-glow discharge plasma polymerization was developed for alkaline anion-exchange membranes synthesis using vinylbenzyl chloride as monomer. X-ray photoelectron spectroscopy and attenuated total reflection Fourier transform infrared spectroscopy were used to characterize the chemical structure properties of plasma-polymerized membranes. Ion-exchange capacities of quaternized poly(vinylbenzyl chloride) (QPVBC) membranes were measured to evaluate their capability of hydroxyl ion transport. A mechanism of plasma polymerization using VBC as monomer that accounts for the competitive effects of free radicals polymerization and plasma ablation in the plasma polymerization process was proposed. Our results indicate that plasma discharge power influences the contents of functional groups and the structure of the plasma polymer membranes, which attribute to the coactions of polymerization and ablation. The properties of uniform morphology, good adhesion to the substrate, high thermal stability and satisfying anion conduction level suggest the potential application of QPVBC membrane deposited at discharge power of 20 W in alkaline direct methanol fuel cells.

Dark matter signals from Draco and Willman 1: prospects for MAGIC II and CTA

Science.gov (United States)

Bringmann, Torsten; Doro, Michele; Fornasa, Mattia

2009-01-01

The next generation of ground-based Imaging Air Cherenkov Telescopes will play an important role in indirect dark matter searches. In this article, we consider two particularly promising candidate sources for dark matter annihilation signals, the nearby dwarf galaxies Draco and Willman 1, and study the prospects of detecting such a signal for the soon-operating MAGIC II telescope system as well as for the planned installation of CTA, taking special care of describing the experimental features that affect the detectional prospects. For the first time in such studies, we fully take into account the effect of internal bremsstrahlung, which has recently been shown to considerably enhance, in some cases, the gamma-ray flux in the high energies domain where Atmospheric Cherenkov Telescopes operate, thus leading to significantly harder annihilation spectra than traditionally considered. While the detection of the spectral features introduced by internal bremsstrahlung would constitute a smoking gun signature for dark matter annihilation, we find that for most models the overall flux still remains at a level that will be challenging to detect, unless one adopts somewhat favorable descriptions of the smooth dark matter distribution in the dwarfs.

Laser microstructuring for fabricating superhydrophobic polymeric surfaces

Science.gov (United States)

Cardoso, M. R.; Tribuzi, V.; Balogh, D. T.; Misoguti, L.; Mendonça, C. R.

2011-02-01

In this paper we show the fabrication of hydrophobic polymeric surfaces through laser microstructuring. By using 70-ps pulses from a Q-switched and mode-locked Nd:YAG laser at 532 nm, we were able to produce grooves with different width and separation, resulting in square-shaped pillar patterns. We investigate the dependence of the morphology on the surface static contact angle for water, showing that it is in agreement with the Cassie-Baxter model. We demonstrate the fabrication of a superhydrophobic polymeric surface, presenting a water contact angle of 157°. The surface structuring method presented here seems to be an interesting option to control the wetting properties of polymeric surfaces.

Applications of polymeric micelles with tumor targeted in chemotherapy

International Nuclear Information System (INIS)

Ding Hui; Wang Xiaojun; Zhang Song; Liu Xinli

2012-01-01

Polymeric micelles (PMs) have gained more progress as a carrier system with the quick development of biological and nanoparticle techniques. In particular, PMs with smart targeting can deliver anti-cancer drugs directly into tumor cells at a sustained rate. PMs with core–shell structure (with diameters of 10 ∼ 100 nm) have been prepared by a variety of biodegradable and biocompatible polymers via a self-assembly process. The preparation of polymeric micelles with stimuli-responsive block copolymers or modification of target molecules on polymeric micelles’ surface are able to significantly improve the efficiency of drug delivery. Polymeric micelles, which have been considered as a novel promising drug carrier for cancer therapeutics, are rapidly evolving and being introduced in an attempt to overcome several limitations of traditional chemotherapeutics, including water solubility, tumor-specific accumulation, anti-tumor efficacy, and non-specific toxicity. This review describes the preparation of polymeric micelles and the targeted modification which greatly enhance the effects of chemotherapeutic agents.

Self-Propagating Frontal Polymerization in Water at Ambient Pressure

Science.gov (United States)

Olten, Nesrin; Kraigsley, Alison; Ronney, Paul D.

2003-01-01

Advances in polymer chemistry have led to the development of monomers and initiation agents that enable propagating free-radical polymerization fronts to exist. These fronts are driven by the exothermicity of the polymerization reaction and the transport of heat from the polymerized product to the reactant monomer/solvent/initiator solution. The thermal energy transported to the reactant solution causes the initiator to decompose, yielding free radicals, which start the free radical polymerization process as discussed in recent reviews. The use of polymerization processes based on propagating fronts has numerous applications. Perhaps the most important of these is that it enables rapid curing of polymers without external heating since the polymerization process itself provides the high temperatures necessary to initiate and sustain polymerization. This process also enables more uniform curing of arbitrarily thick samples since it does not rely on heat transfer from an external source, which will necessarily cause the temperature history of the sample to vary with distance from the surface according to a diffusion-like process. Frontal polymerization also enables filling and sealing of structures having cavities of arbitrary shape without having to externally heat the structure. Water at atmospheric pressure is most convenient solvent to employ and the most important for practical applications (because of the cost and environmental issues associated with DMSO and other solvents). Nevertheless, to our knowledge, steady, self-propagating polymerization fronts have not been reported in water at atmospheric pressure. Currently, polymerization fronts require a high boiling point solvent (either water at high pressures or an alternative solvent such as dimethyl sulfoxide (DMSO) (boiling point 189 C at atmospheric pressure.) Early work on frontal polymerization, employed pressures up to 5000 atm in order to avoid boiling of the monomer/solvent/initiator solution. High

Heterofunctional Glycopolypeptides by Combination of Thiol-Ene Chemistry and NCA Polymerization.

Science.gov (United States)

Krannig, Kai-Steffen; Schlaad, Helmut

2016-01-01

Glycopolypeptides are prepared either by the polymerization of glycosylated amino acid N-carboxyanhydrides (NCAs) or by the post-polymerization functionalization of polypeptides with suitable functional groups. Here we present a method for the in-situ functionalization and (co-) polymerization of allylglycine N-carboxyanhydride in a facile one-pot procedure, combining radical thiol-ene photochemistry and nucleophilic ring-opening polymerization techniques, to yield well-defined heterofunctional glycopolypeptides.

Polymerization Initiated at the Sidewalls of Carbon Nanotubes

Science.gov (United States)

Tour, James M.; Hudson, Jared L.

2011-01-01

A process has been developed for growing polymer chains via anionic, cationic, or radical polymerization from the side walls of functionalized carbon nanotubes, which will facilitate greater dispersion in polymer matrices, and will greatly enhance reinforcement ability in polymeric material.

Investigations in the field of solid state polymerization Pt. 38

International Nuclear Information System (INIS)

Hardy, Gy.; Cser, F.; Nyitrai, K.; Fedorova, N.

1980-01-01

The stuctural and radiation chemical data of vinyl monomers with long chain paraffinic or cholesteric side groups are critically reviewed. Based on their structural and polymerization kinetical characteristics the monomers may be classified into three groups. Oblique layers are favourable for homogeneous topotactic polymerization. This is characterized by a low activation energy and a radiochemical efficiency very similar to that measured in liquid state polymerization. The tilted layers are not favourable for homogeneous topotactic polymerization. Allyl monomers yield polymers with higher molecular weights in the layer structure than in liquid states. (author)

Biocompatible Polymeric Materials Intended for Drug Delivery and Therapeutic Applications

DEFF Research Database (Denmark)

Hvilsted, Søren; Javakhishvili, Irakli; Bednarek, Melania

2007-01-01

of polymer blocks by “click chemistry”. An all polymerization strategy would imply preparing polymers by living/controlled techniques in such a manner that one block after polymerization can be converted to a macroinitiator enabling the second block to polymerize. The coupling strategy invariably inserts...... a linking unit, 1,4-triazol, resulting from the catalyzed, irreversible 1,3-dipolar cycloaddition reaction between an alkyne and an azide. Thus, this strategy necessitates the proper end functionalization of the polymeric building blocks. Fortunately the 1,4-triazol unit is FDA approved already existing...

Polymeric Nanogels Obtained by Radiation Technique

Energy Technology Data Exchange (ETDEWEB)

Ulanski, P.; Kadłubowski, A. K.; Olejnik,; Rokita, B.; Wach, R.; Rosiak, J. M. [Institute of Applied Radiation Chemistry, Technical University of Lodz, Lodz (Poland)

2009-07-01

Soft nanomaterials - polymeric nanogels and microgels - have made a fast and brilliant career, from an unwanted by-product of polymerization processes to an important and fashionable topic of interdisciplinary research in the fields of polymer chemistry and physics, materials science, pharmacy and medicine. Together with their larger analogues - macroscopic gels, most known in the form of water-swellable hydrogels - they have a broad field of actual and potential applications ranging from filler materials in coating industry to modern biomaterials.

Polymeric Nanogels Obtained by Radiation Technique

International Nuclear Information System (INIS)

Ulanski, P.; Kadłubowski, A.K.; Olejnik; Rokita, B.; Wach, R.; Rosiak, J.M.

2009-01-01

Soft nanomaterials - polymeric nanogels and microgels - have made a fast and brilliant career, from an unwanted by-product of polymerization processes to an important and fashionable topic of interdisciplinary research in the fields of polymer chemistry and physics, materials science, pharmacy and medicine. Together with their larger analogues - macroscopic gels, most known in the form of water-swellable hydrogels - they have a broad field of actual and potential applications ranging from filler materials in coating industry to modern biomaterials

Recent progress of atomic layer deposition on polymeric materials

Energy Technology Data Exchange (ETDEWEB)

Guo, Hong Chen; Ye, Enyi [Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, Innovis, #08-03, Singapore 138634 (Singapore); Li, Zibiao, E-mail: lizb@imre.a-star.edu.sg [Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, Innovis, #08-03, Singapore 138634 (Singapore); Han, Ming-Yong [Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, Innovis, #08-03, Singapore 138634 (Singapore); Loh, Xian Jun, E-mail: lohxj@imre.a-star.edu.sg [Institute of Materials Research and Engineering, A*STAR (Agency for Science, Technology and Research), 2 Fusionopolis Way, Innovis, #08-03, Singapore 138634 (Singapore); Department of Materials Science and Engineering, National University of Singapore, Singapore 117574 (Singapore); Singapore Eye Research Institute, 20 College Road, Singapore 169856 (Singapore)

2017-01-01

As a very promising surface coating technology, atomic layer deposition (ALD) can be used to modify the surfaces of polymeric materials for improving their functions and expanding their application areas. Polymeric materials vary in surface functional groups (number and type), surface morphology and internal structure, and thus ALD deposition conditions that typically work on a normal solid surface, usually do not work on a polymeric material surface. To date, a large variety of research has been carried out to investigate ALD deposition on various polymeric materials. This paper aims to provide an in-depth review of ALD deposition on polymeric materials and its applications. Through this review, we will provide a better understanding of surface chemistry and reaction mechanism for controlled surface modification of polymeric materials by ALD. The integrated knowledge can aid in devising an improved way in the reaction between reactant precursors and polymer functional groups/polymer backbones, which will in turn open new opportunities in processing ALD materials for better inorganic/organic film integration and potential applications. - Highlights: • ALD deposition on different natural and synthetic polymer materials • Reaction mechanism based on the surface functional groups of polymers • Application of ALD-modified polymers in different fields.

Thermal gradient brine inclusion migration in salt study: gas-liquid inclusions, preliminary model

International Nuclear Information System (INIS)

Olander, D.R.; Machiels, A.J.

1979-10-01

Natural salt deposits contain small cubical inclusions of brine distributed through the salt. Temperature gradients, resulting from storing heat-generating wastes in the salt, can cause the inclusions to move through the salt. Prediction of the rate and amount of brine-inclusion migration is necessary for the evaluation of bedded or domed salts as possible media for waste repositories. Inclusions filled exclusively with liquid migrate up the temperature gradient towards the heat source. The solubility of salt in the brine inclusion increases with temperature. Consequently, salt dissolves into the inclusion across the hot surface and crystallizes out at the cold surface. Diffusion of salt within the liquid phase from the hot to the cold faces causes the inclusions to move in the opposite direction. In so doing, they change shape and eventually become rectangular parallelipipeds with a width (dimension perpendicular to the thermal gradient) much larger than the thickness (dimension in the direction of the thermal gradient). The inclusions may also contain a gas phase predominantly consisting of water vapor. These entities are termed two-phase or gas-liquid inclusions. The two-phase inclusions usually migrate down the temperature gradient away from the heat source remaining more-or-less cubical. A two-phase inclusion also forms when an all-liquid inclusion reaches the waste package; upon opening up at the salt-package interface, the brine partially evaporates and the inclusion reseals with some insoluble gas trapped inside. These gas-liquid inclusions proceed to move down the temperature gradient, in the opposite sense of the all-liquid inclusions. The gas-liquid inclusions phenomenon provides a pathway by which radionuclides leached from the wasteform by the brine can be transported away from the waste package and thus might have greater access to the biosphere

Electrocatalytic reduction of oxygen at vapor phase polymerized ...

African Journals Online (AJOL)

We successfully polymerized poly(3,4-ethylenedioxidethiophene) by vapor phase polymerization technique on rotating glassy carbon disk electrode. The catalytic activity of this electrode towards oxygen reduction reaction was investigated and showed remarkable activity. Rotating disk voltammetry was used to study the ...

Synthesis of Terpyridine-Terminated Polymers by Anionic Polymerization

NARCIS (Netherlands)

Guerrero-Sanchez, C.A.; Lohmeijer, B.G.G.; Meier, M.A.R.; Schubert, U.S.

2005-01-01

The synthesis of terpyridine-functionalized polystyrene was achieved by reacting 4‘-chloro-2,2‘:6‘,2‘ ‘-terpyridine (terminating agent) with "living" polymeric carbanions synthesized by anionic polymerization. The obtained polymers were characterized by gel permeation chromatography, nuclear

prepared via atom transfer radical polymerization, reverse atom

Indian Academy of Sciences (India)

Synthesis and characterization of poly(2-ethylhexyl acrylate) prepared via atom transfer radical polymerization, reverse atom transfer radical polymerization and ... Zydex Industries, 25-A Gandhi Oil Mill Compound, Gorwa, Vadodara 390 016, India; Rubber Technology Centre, Indian Institute of Technology Kharagpur, ...

Colloidal templating : a route towards controlled synthesis of functional polymeric nanoparticles

NARCIS (Netherlands)

Ali, S.I.

2010-01-01

Template-directed synthesis of polymeric nanoparticles offers better control over particle morphology, shape, structure, composition and properties compare to the conventional emulsion polymerization routes. For the production of anisotropic polymer-clay composite latex particles and polymeric

Inclusive Education in Italy: Description and Reflections on Full Inclusion

Science.gov (United States)

Anastasiou, Dimitris; Kauffman, James M.; Di Nuovo, Santo

2015-01-01

Inclusion of students with disabilities when appropriate is an important goal of special education for students with special needs. Full inclusion, meaning no education for any child in a separate setting, is held to be desirable by some, and Italy is likely the nation with an education system most closely approximating full inclusion on the…

13C Kinetic isotopic effect of polymerization on monomers with multiple bond

International Nuclear Information System (INIS)

Berman, E.L.; Polyakov, V.B.; Makovetskij, K.L.; Golenko, T.G.; Galimov, Eh.M.; AN SSSR, Moscow. Inst. Organicheskoj Khimii; AN SSSR, Moscow. Inst. Geokhimii i Analiticheskoj Khimii)

1988-01-01

13 C kinetic isotopic effect (KIE) of anionic and radical polymerization and metathesis reaction of monomers with multiple bonds are studied and correlation between the found KIE values of polymerization and the structure of transition state is established. 13 C KIE of polymerization reactions are investigated using monomers with natural content of the isotope. Polymerization was carried out using high-vacuum equipment: radical polymerization of methyl acrylate (MA) and vinyl acetate in benzene solution under the effect of benzoyl peroxide (60 deg C); anionic polymerization of MA, initiated by potassium butyl cellosolvolate, was realized in mass at 25 deg C; cyclopentene metathesis reaction was conducted in benzene under the effect of initiating system WCl 6 - (C 3 H 5 ) 2 Si(CH 3 ) 2 at -30 deg C; phenylacetylene polymers were prepared by polymerization in benzene solution at 20 deg C under the effect of WCl 6 . It is ascertained that 13 C KIE of radical and anionic polymerization of olefins and cycloolefin metathesis constitutes 2.0 -2.4%. Polymerization of compound with ternary bond is accompanied by a lower value of 13 C KIE (<1%), which is explained by double bond of reacting bond in transition state

Bioactive Polymeric Materials for Tissue Repair

Directory of Open Access Journals (Sweden)

Diane R. Bienek

2017-01-01

Full Text Available Bioactive polymeric materials based on calcium phosphates have tremendous appeal for hard tissue repair because of their well-documented biocompatibility. Amorphous calcium phosphate (ACP-based ones additionally protect against unwanted demineralization and actively support regeneration of hard tissue minerals. Our group has been investigating the structure/composition/property relationships of ACP polymeric composites for the last two decades. Here, we present ACP’s dispersion in a polymer matrix and the fine-tuning of the resin affects the physicochemical, mechanical, and biological properties of ACP polymeric composites. These studies illustrate how the filler/resin interface and monomer/polymer molecular structure affect the material’s critical properties, such as ion release and mechanical strength. We also present evidence of the remineralization efficacy of ACP composites when exposed to accelerated acidic challenges representative of oral environment conditions. The utility of ACP has recently been extended to include airbrushing as a platform technology for fabrication of nanofiber scaffolds. These studies, focused on assessing the feasibility of incorporating ACP into various polymer fibers, also included the release kinetics of bioactive calcium and phosphate ions from nanofibers and evaluate the biorelevance of the polymeric ACP fiber networks. We also discuss the potential for future integration of the existing ACP scaffolds into therapeutic delivery systems used in the precision medicine field.

Polymeric peptide pigments with sequence-encoded properties

Energy Technology Data Exchange (ETDEWEB)

Lampel, Ayala; McPhee, Scott A.; Park, Hang-Ah; Scott, Gary G.; Humagain, Sunita; Hekstra, Doeke R.; Yoo, Barney; Frederix, Pim W. J. M.; Li, Tai-De; Abzalimov, Rinat R.; Greenbaum, Steven G.; Tuttle, Tell; Hu, Chunhua; Bettinger, Christopher J.; Ulijn, Rein V.

2017-06-08

Melanins are a family of heterogeneous polymeric pigments that provide ultraviolet (UV) light protection, structural support, coloration, and free radical scavenging. Formed by oxidative oligomerization of catecholic small molecules, the physical properties of melanins are influenced by covalent and noncovalent disorder. We report the use of tyrosine-containing tripeptides as tunable precursors for polymeric pigments. In these structures, phenols are presented in a (supra-)molecular context dictated by the positions of the amino acids in the peptide sequence. Oxidative polymerization can be tuned in a sequence-dependent manner, resulting in peptide sequence–encoded properties such as UV absorbance, morphology, coloration, and electrochemical properties over a considerable range. Short peptides have low barriers to application and can be easily scaled, suggesting near-term applications in cosmetics and biomedicine.

Interfacial Polymerization of Polyaniline Nanofibers Grafted to Au Surfaces

National Research Council Canada - National Science Library

Sawall, D

2004-01-01

.... The in-situ polymerization technique of these PANI nanofibers in the presence of sulfonated polystyrene allowed for the growth of PANI 2-D nanostructures embedded in the polymerized sulfonated host...

Hydroxyapatite induces spontaneous polymerization of model self-etch dental adhesives.

Science.gov (United States)

Zhang, Ying; Wu, Ningjing; Bai, Xinyan; Xu, Changqi; Liu, Yi; Wang, Yong

2013-10-01

The objective of this study is to report for the first time the spontaneous polymerization phenomenon of self-etch dental adhesives induced by hydroxylapatite (HAp). Model self-etch adhesives were prepared by using a monomer mixture of bis[2-(methacryloyloxy)ethyl] phosphate (2MP) with 2-hydroxyethyl methacrylate (HEMA). The initiator system consisted of camphorquinone (CQ, 0.022 mmol/g) and ethyl 4-dimethylaminobenzoate (4E, 0.022-0.088 mmol/g). HAp (2-8 wt.%) was added to the neat model adhesive. In a dark environment, the polymerization was monitored in-situ using ATR/FT-IR, and the mechanical properties of the polymerized adhesives were evaluated using nanoindentation technique. Results indicated that spontaneous polymerization was not observed in the absence of HAp. However, as different amounts of HAp were incorporated into the adhesives, spontaneous polymerization was induced. Higher HAp content led to higher degree of conversion (DC), higher rate of polymerization (RP) and shorter induction period (IP). In addition, higher 4E content also elevated DC and RP and reduced IP of the adhesives. Nanoindentation result suggested that the Young's modulus of the polymerized adhesives showed similar dependence on HAp and 4E contents. In summary, interaction with HAp could induce spontaneous polymerization of the model self-etch adhesives. This result provides important information for understanding the initiation mechanism of the self-etch adhesives, and may be of clinical significance to strengthen the adhesive/dentin interface based on the finding. Copyright © 2013 Elsevier B.V. All rights reserved.

Delimiting Inclusive Design

DEFF Research Database (Denmark)

Herriott, Richard

2014-01-01

This paper was written as an answer to the question raised by my PhD dissertation on accessibility through user-centred and Inclusive Design (ID) methods: can Inclusive Design be delimited? The literature on Inclusive Design deals almost entrirely with consumer product design and assistive...

Facile synthesis of polymeric fluorescent organic nanoparticles based on the self-polymerization of dopamine for biological imaging.

Science.gov (United States)

Shi, Yingge; Jiang, Ruming; Liu, Meiying; Fu, Lihua; Zeng, Guangjian; Wan, Qing; Mao, Liucheng; Deng, Fengjie; Zhang, Xiaoyong; Wei, Yen

2017-08-01

Polymeric fluorescent organic nanoparticles (polymer-FONs) have raised considerable research attention for biomedical applications owing to their advantages as compared with fluorescent inorganic nanoparticles and small organic molecules. In this study, we presented an efficient, facile and environment-friendly strategy to produce polymer-FONs, which relied on the self-polymerization of dopamine and polyethyleneimine (PEI) in rather mild conditions. To obtain the final polymer-FONs, aldehyde group-containing copolymers (named as poly(UA-co-PEGMA)) were synthesized by reversible addition-fragmentation chain-transfer polymerization using polyethylene glycol methyl ether methacrylate (PEGMA) and 1-undecen-10-al (UA) as monomers. The dopamine was conjugated onto poly(UA-co-PEGMA) through a multicomponent reaction between UA and dopamine to obtain poly(UA-co-PEGMA)-DA, which was further utilized for preparation of polymer-FONs through self-polymerization of dopamine and PEI. 1 H nuclear magnetic resonance, Fourier transform infrared spectroscopy, transmission electron microscopy and fluorescence spectroscopy were employed to characterize the structure, morphology, compositions and optical properties of these polymer-FONs. Cell viability and cell uptake behavior results suggested that these polymer-FONs possess good biocompatibility and can be potentially utilized for biomedical applications. More importantly, the method can be also applied to fabricate many other multifunctional polymer-FONs with great potential for biomedical applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Modelling the Load Torques of Electric Drive for Polymerization Process

Directory of Open Access Journals (Sweden)

Andrzej Popenda

2007-01-01

Full Text Available The problems of mathematical modelling the load torques on shaft of driving motor designed for applications in polymerization reactors are presented in the paper. The real load of polymerization drive is determined as a function of angular velocity. Mentioned function results from friction in roll-formed slide bearing as well as from friction of ethylene molecules with mixer arms in polymerization reactor chamber. Application of mathematical formulas concerning the centrifugal ventilator is proposed to describe the mixer in reactor chamber. The analytical formulas describing the real loads of polymerization drive are applied in mathematical modelling the power unit of polymerization reactor with specially designed induction motor. The numerical analysis of transient states was made on the basis of formulated mathematical model. Examples of transient responses and trajectories resulting from analysis are presented in the paper.

Radiation initiated polymerization of trioxane and stabilization of polyoxymethylene

International Nuclear Information System (INIS)

Rao, M.H.; Ramanan, G.; Kunjappu, J.T.; Rao, K.N.

1990-01-01

Gamma ray induced polymerization of trioxane from an indigenous source (M/s. Nuchem Plastics, Faridabad) has been investigated by both in-source and post polymerization techniques. Impurity levels in the trioxane samples are determined and compared with those in an imported material. Critical evaluation of the results of its purification by different methods, viz. treatment with molecular sieves, crystallization from solvents and their variations, has been carried out prior to optimising the conditions of polymerization. A novel but simple purification procedure employing benzene as the solvent which is found to form a ternary azeotrope with trioxane and water has been developed. The effect of these purification methods on the polymerization efficiency and their dependence on the molecular weight of the polymer formed are also discussed. Experimental details of polymerizing trioxane in 10 kg scale are also described. To improve upon the thermal stabilty of the polyoxymethylene thus formed, protection of the free hydroxyl end groups (end-capping) has been achieved by an acetylation procedure using acetic anhydride in presence of catalytic amounts of sodium acetate. (author). 11 tabs., 4 figs

Social imaginaries and inclusion

DEFF Research Database (Denmark)

Hansen, Janne Hedegaard

2016-01-01

that inclusion on the one hand may be seen to be about human rights, solidarity, and democracy, and on the other hand, it is about ensuring the cohesion of neoliberal society by means of every person’s obligation to realize one’s potential through learning, development, and education regardless of one’s needs......, the development of inclusive schools and inclusive learning environments will involve both inclusion and exclusion processes. With this starting point, international educational research knowledge about inclusive schools and inclusive learning environments in general will be related to the fundamental dilemma...

Comparison of potentials for polymeric liquids

International Nuclear Information System (INIS)

Jung, Hae Young

2002-01-01

Many theories for polymeric liquids are based on the concepts of cell, hole, free volume of lattice etc. In this theories, van der Waals potential, Lennard-Jones 6-12 potential and their modified potentials are commonly used. In this work, Mie(p,6)potential was applied to the Continuous Lattice Fluid Theory (which extends the discrete lattices of Lattice Fluid Theory to classically continuous lattices) and Dee-Walsch's Cell Theory (which modifies Flory's Equation of State Theory). Both of them are known to be successful theories for polymeric liquids. Thus, PVT values changing with p (the exponent in the repulsion potential) were calculated and compared with experimental values. And, calculated values of Lattice Fluid theory, Flory's Equation of State Theory and Cho-Sanchez Theory using perturbation method were also compared. Through the calculated results, van der Waals potential, Lennard-Jones 6-12 potential and Mie(p,6) potential for polymeric liquids were compared with each other

Numerical study of the thermal degradation of isotropic and anisotropic polymeric materials

Energy Technology Data Exchange (ETDEWEB)

Soler, E. [Departamento de Lenguajes y Ciencias de la Computacion, ETSI Informatica, Universidad de Malaga, 29071 Malaga (Spain); Ramos, J.I. [Room I-320-D, ETS Ingenieros Industriales, Universidad de Malaga, Plaza El Ejido, s/n, 29013 Malaga (Spain)

2005-08-01

The thermal degradation of two-dimensional isotropic, orthotropic and anisotropic polymeric materials is studied numerically by means of a second-order accurate (in both space and time) linearly implicit finite difference formulation which results in linear algebraic equations at each time step. It is shown that, for both isotropic and orthotropic composites, the monomer mass diffusion tensor plays a role in initiating the polymerization kinetics, the formation of a polymerization kernel and the initial front propagation, whereas the later stages of the polymerization are nearly independent of the monomer mass diffusion tensor. In anisotropic polymeric composites, it has been found that the monomer mass diffusion tensor plays a paramount role in determining the initial stages of the polymerization and the subsequent propagation of the polymerization front, the direction and speed of propagation of which are found to be related to the principal directions of both the monomer mass and the heat diffusion tensors. It is also shown that the polymerization time and temperatures depend strongly on the anisotropy of the mass and heat diffusion tensors. (authors)

Radiation Induced Polymerization of Pyrrole

International Nuclear Information System (INIS)

Sarada Idris; Ratnam, C.T.; Ahmad Ashrif Abu Bakar

2016-01-01

We demonstrate the polymerization of pyrrole by gamma irradiation. The pyrrole films were exposed to gamma ray from cobalt 60 source at doses ranging from 0 to 150 kGy. The films were subjected to structural and morphological analyses by using FTIR, SEM and AFM techniques. Similar studies were also made on pristine pyrrole film which serve as control. Results revealed that pyrrole has been successfully polymerized through irradiation induced reactions. The SEM images depicted the formation of cauliflower shape upon gamma irradiation. The structural changes of pyrrole also evidenced by FTIR spectra. Surface topography and roughness of pyrrole before and after gamma irradiation found to show significant differences. (author)

Functional polypeptides obtained by living ring opening polymerizations of N-carboxyanhydrides

NARCIS (Netherlands)

Habraken, G.J.M.

2011-01-01

N-Carboxyanhydride ring opening polymerization (NCA ROP) is a method to prepare polypeptides with a high degree of polymerization in large quantities. The living polymerization technique of NCA ROP gave the opportunity to synthesize many polymer architectures with well-defined blocks and copolymers

In situ stabilizer formation from methacrylic acid macromonomers in emulsion polymerization

NARCIS (Netherlands)

Schreur-Piet, Ingeborg; Heuts, Johan P.A.

2017-01-01

Oligomers of methacrylic acid containing a propenyl ω-endgroup (i.e. MAA-macromonomers) were synthesized by cobalt-mediated catalytic chain transfer polymerization and used as precursors to stabilizers in emulsion polymerization. It was found that only in those polymerizations in which these

Characterization of Plasma-Polymerized Fused Polycyclic Compounds for Binding Conducting Polymers

DEFF Research Database (Denmark)

Winther-Jensen, Bjørn; Norrman, Kion; Kingshott, Peter

2005-01-01

with hydrogen in the position which is able to co-polymerize with thiophene derivatives polymerized by conventional oxidative polymerization, thereby forming a conducting thiophene polymer bonded to the substrate. The durability of the surface modification procedure is demonstrated by micropatterning of PEDT...

Thermodynamic Presynthetic Considerations for Ring-Opening Polymerization.

Science.gov (United States)

Olsén, Peter; Odelius, Karin; Albertsson, Ann-Christine

2016-03-14

The need for polymers for high-end applications, coupled with the desire to mimic nature's macromolecular machinery fuels the development of innovative synthetic strategies every year. The recently acquired macromolecular-synthetic tools increase the precision and enable the synthesis of polymers with high control and low dispersity. However, regardless of the specificity, the polymerization behavior is highly dependent on the monomeric structure. This is particularly true for the ring-opening polymerization of lactones, in which the ring size and degree of substitution highly influence the polymer formation properties. In other words, there are two important factors to contemplate when considering the particular polymerization behavior of a specific monomer: catalytic specificity and thermodynamic equilibrium behavior. This perspective focuses on the latter and undertakes a holistic approach among the different lactones with regard to the equilibrium thermodynamic polymerization behavior and its relation to polymer synthesis. This is summarized in a monomeric overview diagram that acts as a presynthetic directional cursor for synthesizing highly specific macromolecules; the means by which monomer equilibrium conversion relates to starting temperature, concentration, ring size, degree of substitution, and its implications for polymerization behavior are discussed. These discussions emphasize the importance of considering not only the catalytic system but also the monomer size and structure relations to thermodynamic equilibrium behavior. The thermodynamic equilibrium behavior relation with a monomer structure offers an additional layer of complexity to our molecular toolbox and, if it is harnessed accordingly, enables a powerful route to both monomer formation and intentional macromolecular design.

Complex Macromolecular Architectures by Living Cationic Polymerization

KAUST Repository

Alghamdi, Reem D.

2015-05-01

Poly (vinyl ether)-based graft polymers have been synthesized by the combination of living cationic polymerization of vinyl ethers with other living or controlled/ living polymerization techniques (anionic and ATRP). The process involves the synthesis of well-defined homopolymers (PnBVE) and co/terpolymers [PnBVE-b-PCEVE-b-PSiDEGVE (ABC type) and PSiDEGVE-b-PnBVE-b-PSiDEGVE (CAC type)] by sequential living cationic polymerization of n-butyl vinyl ether (nBVE), 2-chloroethyl vinyl ether (CEVE) and tert-butyldimethylsilyl ethylene glycol vinyl ether (SiDEGVE), using mono-functional {[n-butoxyethyl acetate (nBEA)], [1-(2-chloroethoxy) ethyl acetate (CEEA)], [1-(2-(2-(t-butyldimethylsilyloxy)ethoxy) ethoxy) ethyl acetate (SiDEGEA)]} or di-functional [1,4-cyclohexanedimethanol di(1-ethyl acetate) (cHMDEA), (VEMOA)] initiators. The living cationic polymerizations of those monomers were conducted in hexane at -20 0C using Et3Al2Cl3 (catalyst) in the presence of 1 M AcOEt base.[1] The PCEVE segments of the synthesized block terpolymers were then used to react with living macroanions (PS-DPE-Li; poly styrene diphenyl ethylene lithium) to afford graft polymers. The quantitative desilylation of PSiDEGVE segments by n-Bu4N+F- in THF at 0 °C led to graft co- and terpolymers in which the polyalcohol is the outer block. These co-/terpolymers were subsequently subjected to “grafting-from” reactions by atom transfer radical polymerization (ATRP) of styrene to afford more complex macromolecular architectures. The base assisted living cationic polymerization of vinyl ethers were also used to synthesize well-defined α-hydroxyl polyvinylether (PnBVE-OH). The resulting polymers were then modified into an ATRP macro-initiator for the synthesis of well-defined block copolymers (PnBVE-b-PS). Bifunctional PnBVE with terminal malonate groups was also synthesized and used as a precursor for more complex architectures such as H-shaped block copolymer by “grafting-from” or �

21 CFR 872.6070 - Ultraviolet activator for polymerization.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ultraviolet activator for polymerization. 872.6070 Section 872.6070 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... ultraviolet radiation intended to polymerize (set) resinous dental pit and fissure sealants or restorative...

Solid-State Polymerization of Acetylene under Pressure: {ital Ab Initio} Simulation

Energy Technology Data Exchange (ETDEWEB)

Bernasconi, M.; Parrinello, M. [Max-Planck-Institut fuer Festkoerperforschung, Heisenbergstr.1, D-70569 Stuttgart (Germany); Bernasconi, M. [Istituto Nazionale Fisica della Materia and Dipartimento di Fisica, Universita di Milano, Via Celoria 16, 20133 Milano (Italy); Chiarotti, G.; Focher, P.; Tosatti, E. [Istituto Nazionale Fisica della Materia and International School for Advanced Studies, Via Beirut 4, I-34014 Trieste (Italy); Tosatti, E. [International Centre for Theoretical Physics (ICTP), P.O.Box 586, I-34014 Trieste (Italy)

1997-03-01

We have simulated by {ital ab initio} constant pressure molecular dynamics the solid-state polymerization of acetylene recently observed experimentally in the pressure range 3.5{endash}14 GPa. We have found a massive polymerization only at much higher pressure (25 GPa). However, we have also found that a triplet exciton self-trapped on a single, {ital cis}-bent molecule in crystalline acetylene is a very effective polymerization seed at lower pressure ({lt}9GPa), much closer to the experimental threshold. Therefore, we propose that the polymerization observed experimentally is possibly catalyzed by a similar seed. We predict that injection of triplet excitons would greatly enhance the polymerization rate. {copyright} {ital 1997} {ital The American Physical Society}

Synthesis of nanosized (polymerization in miniemulsion employing in situ surfactant formation.

Science.gov (United States)

Guo, Yi; Zetterlund, Per B

2011-10-18

A novel method for synthesis of ultrafine polymeric nanoparticles of diameters less than 20 nm has been developed. The method is based on miniemulsion polymerization exploiting combination of the in situ surfactant generation approach (whereby the surfactant is formed at the oil-water interface by reaction between an organic acid and a base) and ultrasonication. Conventional radical polymerization and nitroxide-mediated radical polymerization of styrene have been conducted in miniemulsion using oleic acid/potassium hydroxide, demonstrating that particles with diameters less than 20 nm can be obtained by this approach at surfactant contents much lower than traditionally required in microemulsion polymerizations. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Noninvasive evaluation of cerebral arteriovenous malformations by 4D-CT angiography using 320-detector row CT

International Nuclear Information System (INIS)

Tajiri, H.; Jin, L.; Tsukiyama, M.; Suzuki, Y.; Sekine, S.; Shimizu, T.; Ohiwa, T.

2012-01-01

Full text: Objective: Four-dimensional computed tomography angiography (4D-CTA) is a new and promising technique in the diagnosis of patients with cerebral arteriovenous malformations (AVMs). The purpose of this retrospective study was to investigate the utility of 4D-CTA using whole-brain 320-detector row CT for assessing cerebral AVMs compared with conventional angiography (CA). Materials and methods: Participants included patients admitted to our institution from November 2010 to March 2012 due to cerebral AVMs who underwent both 4D-CTA and CA within 14 days. The diagnosis of AVM was finally confirmed by CA. Two readers reviewed 4D-CTA and CA under consensus regarding AVM detection rate and each component of the AVM (feeders, nidi, drainers) using a four-point grading scale (excellent=3, good=2, fair=1, poor=0), and the Spetzler-Martin (S-M) grade. Results: During the study period, 11 patients met the inclusion criteria. The average score for feeders, nidi, and drainers was 2.0, 2.3, and 2.5 in 4D-CTA and 2.4, 2.6, and 2.7 in CA, respectively. The average S-M grade score was 2.0 in all patients. There were no statistically significant differences between the two modalities (P<.005). Conclusion: 4D-CTA using 320-detector row CT is a very reliable method and offers diagnostic performance equivalent to CA for detecting and predicting S-M classification of cerebral AVMs.

Phenotypic variability within the inclusion body spectrum of basophilic inclusion body disease and neuronal intermediate filament inclusion disease in frontotemporal lobar degenerations with FUS-positive inclusions.

Science.gov (United States)

Gelpi, Ellen; Lladó, Albert; Clarimón, Jordi; Rey, Maria Jesús; Rivera, Rosa Maria; Ezquerra, Mario; Antonell, Anna; Navarro-Otano, Judith; Ribalta, Teresa; Piñol-Ripoll, Gerard; Pérez, Anna; Valldeoriola, Francesc; Ferrer, Isidre

2012-09-01

Basophilic inclusion body disease and neuronal intermediate filament inclusion disease (NIFID) are rare diseases included among frontotemporal lobar degenerations with FUS-positive inclusions (FTLD-FUS). We report clinical and pathologic features of 2 new patients and reevaluate neuropathologic characteristics of 2 previously described cases, including an early-onset case of basophilic inclusion body disease (aged 38 years) with a 5-year disease course and abundant FUS-positive inclusion bodies and 3 NIFID cases. One NIFID case (aged 37 years) presented with early-onset psychiatric disturbances and rapidly progressive cognitive decline. Two NIFID cases had later onset (aged 64 years and 70 years) and complex neurologic deficits. Postmortem neuropathologic studies in late-onset NIFID cases disclosed α-internexin-positive "hyaline conglomerate"-type inclusions that were positive with 1 commercial anti-FUS antibody directed to residues 200 and 250, but these were negative to amino acids 90 and 220 of human FUS. Early-onset NIFID had similar inclusions that were positive with both commercial anti-FUS antibodies. Genetic testing performed on all cases revealed no FUS gene mutations. These findings indicate that phenotypic variability in NIFID, including clinical manifestations and particular neuropathologic findings, may be related to the age at onset and individual differences in the evolution of lesions.

Mechanism and kinetics of addition polymerizations

CERN Document Server

Kucera, M

1991-01-01

This volume presents an up-to-date survey of knowledge concerning addition type polymerizations. It contains nine chapters, each of which covers a particular basic term. Whenever necessary, the phenomena are discussed from the viewpoint of both stationary and non-stationary state of radical, ionic (i.e. anionic and cationic) and coordination polymerization. Special attention has been paid to the propagation process. It provides not only a general overview but also information on important special cases (theoretical conditions of propagation, influence of external factors, controlled propagatio

Preparation of Bottlebrush Polymers via a One-Pot Ring-Opening Polymerization (ROP) and Ring-Opening Metathesis Polymerization (ROMP) Grafting-Through Strategy.

Science.gov (United States)

Radzinski, Scott C; Foster, Jeffrey C; Matson, John B

2016-04-01

Bottlebrush polymers are synthesized using a tandem ring-opening polymerization (ROP) and ring-opening metathesis polymerization (ROMP) strategy. For the first time, ROP and ROMP are conducted sequentially in the same pot to yield well-defined bottlebrush polymers with molecular weights in excess of 10(6) Da. The first step of this process involves the synthesis of a polylactide macromonomer (MM) via ROP of d,l-lactide initiated by an alcohol-functionalized norbornene. ROMP grafting-through is then carried out in the same pot to produce the bottlebrush polymer. The applicability of this methodology is evaluated for different MM molecular weights and bottlebrush backbone degrees of polymerization. Size-exclusion chromatographic and (1)H NMR spectroscopic analyses confirm excellent control over both polymerization steps. In addition, bottlebrush polymers are imaged using atomic force microscopy and stain-free transmission electron microscopy on graphene oxide. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A simple method for determining polymeric IgA-containing immune complexes.

Science.gov (United States)

Sancho, J; Egido, J; González, E

1983-06-10

A simplified assay to measure polymeric IgA-immune complexes in biological fluids is described. The assay is based upon the specific binding of a secretory component for polymeric IgA. In the first step, multimeric IgA (monomeric and polymeric) immune complexes are determined by the standard Raji cell assay. Secondly, labeled secretory component added to the assay is bound to polymeric IgA-immune complexes previously fixed to Raji cells, but not to monomeric IgA immune complexes. To avoid false positives due to possible complement-fixing IgM immune complexes, prior IgM immunoadsorption is performed. Using anti-IgM antiserum coupled to CNBr-activated Sepharose 4B this step is not time-consuming. Polymeric IgA has a low affinity constant and binds weakly to Raji cells, as Scatchard analysis of the data shows. Thus, polymeric IgA immune complexes do not bind to Raji cells directly through Fc receptors, but through complement breakdown products, as with IgG-immune complexes. Using this method, we have been successful in detecting specific polymeric-IgA immune complexes in patients with IgA nephropathy (Berger's disease) and alcoholic liver disease, as well as in normal subjects after meals of high protein content. This new, simple, rapid and reproducible assay might help to study the physiopathological role of polymeric IgA immune complexes in humans and animals.

Reversible and Irreversible Binding of Nanoparticles to Polymeric Surfaces

Directory of Open Access Journals (Sweden)

Wolfgang H. Binder

2009-01-01

Full Text Available Reversible and irreversible binding of CdSe-nanoparticles and nanorods to polymeric surfaces via a strong, multiple hydrogen bond (= Hamilton-receptor/barbituric acid is described. Based on ROMP-copolymers, the supramolecular interaction on a thin polymer film is controlled by living polymerization methods, attaching the Hamilton-receptor in various architectures, and concentrations. Strong binding is observed with CdSe-nanoparticles and CdSe-nanorods, whose surfaces are equipped with matching barbituric acid-moieties. Addition of polar solvents, able to break the hydrogen bonds leads to the detachment of the nanoparticles from the polymeric film. Irreversible binding is observed if an azide/alkine-“click”-reaction is conducted after supramolecular recognition of the nanoparticles on the polymeric surface. Thus reversible or irreversible attachment of the nanosized objects can be achieved.

Highly reflective polymeric substrates functionalized utilizing atomic layer deposition

Science.gov (United States)

Zuzuarregui, Ana; Coto, Borja; Rodríguez, Jorge; Gregorczyk, Keith E.; Ruiz de Gopegui, Unai; Barriga, Javier; Knez, Mato

2015-08-01

Reflective surfaces are one of the key elements of solar plants to concentrate energy in the receivers of solar thermal electricity plants. Polymeric substrates are being considered as an alternative to the widely used glass mirrors due to their intrinsic and processing advantages, but optimizing both the reflectance and the physical stability of polymeric mirrors still poses technological difficulties. In this work, polymeric surfaces have been functionalized with ceramic thin-films by atomic layer deposition. The characterization and optimization of the parameters involved in the process resulted in surfaces with a reflection index of 97%, turning polymers into a real alternative to glass substrates. The solution we present here can be easily applied in further technological areas where seemingly incompatible combinations of polymeric substrates and ceramic coatings occur.

Highly reflective polymeric substrates functionalized utilizing atomic layer deposition

Energy Technology Data Exchange (ETDEWEB)

Zuzuarregui, Ana, E-mail: a.zuzuarregui@nanogune.eu; Gregorczyk, Keith E. [CIC Nanogune Consolider, de Tolosa Hiribidea 76, 20018 San Sebastián (Spain); Coto, Borja; Ruiz de Gopegui, Unai; Barriga, Javier [IK4-Tekniker, Iñaki Goenaga 5, 20600 Eibar (Spain); Rodríguez, Jorge [Torresol Energy (SENER Group), Avda. de Zugazarte 61, 48930 Las Arenas (Spain); Knez, Mato [CIC Nanogune Consolider, de Tolosa Hiribidea 76, 20018 San Sebastián (Spain); IKERBASQUE Basque Foundation for Science, Maria Diaz de Haro 3, 48013 Bilbao (Spain)

2015-08-10

Reflective surfaces are one of the key elements of solar plants to concentrate energy in the receivers of solar thermal electricity plants. Polymeric substrates are being considered as an alternative to the widely used glass mirrors due to their intrinsic and processing advantages, but optimizing both the reflectance and the physical stability of polymeric mirrors still poses technological difficulties. In this work, polymeric surfaces have been functionalized with ceramic thin-films by atomic layer deposition. The characterization and optimization of the parameters involved in the process resulted in surfaces with a reflection index of 97%, turning polymers into a real alternative to glass substrates. The solution we present here can be easily applied in further technological areas where seemingly incompatible combinations of polymeric substrates and ceramic coatings occur.

Highly reflective polymeric substrates functionalized utilizing atomic layer deposition

International Nuclear Information System (INIS)

Zuzuarregui, Ana; Gregorczyk, Keith E.; Coto, Borja; Ruiz de Gopegui, Unai; Barriga, Javier; Rodríguez, Jorge; Knez, Mato

2015-01-01

Reflective surfaces are one of the key elements of solar plants to concentrate energy in the receivers of solar thermal electricity plants. Polymeric substrates are being considered as an alternative to the widely used glass mirrors due to their intrinsic and processing advantages, but optimizing both the reflectance and the physical stability of polymeric mirrors still poses technological difficulties. In this work, polymeric surfaces have been functionalized with ceramic thin-films by atomic layer deposition. The characterization and optimization of the parameters involved in the process resulted in surfaces with a reflection index of 97%, turning polymers into a real alternative to glass substrates. The solution we present here can be easily applied in further technological areas where seemingly incompatible combinations of polymeric substrates and ceramic coatings occur

Polymeric bionanocomposite cast thin films with in situ laccase-catalyzed polymerization of dopamine for biosensing and biofuel cell applications.

Science.gov (United States)

Tan, Yueming; Deng, Wenfang; Li, Yunyong; Huang, Zhao; Meng, Yue; Xie, Qingji; Ma, Ming; Yao, Shouzhuo

2010-04-22

We report here on the facile preparation of polymer-enzyme-multiwalled carbon nanotubes (MWCNTs) cast films accompanying in situ laccase (Lac)-catalyzed polymerization for electrochemical biosensing and biofuel cell applications. Lac-catalyzed polymerization of dopamine (DA) as a new substrate was examined in detail by UV-vis spectroscopy, cyclic voltammetry, quartz crystal microbalance, and scanning electron microscopy. Casting the aqueous mixture of DA, Lac and MWCNTs on a glassy carbon electrode (GCE) yielded a robust polydopamine (PDA)-Lac-MWCNTs/GCE that can sense hydroquinone with 643 microA mM(-1) cm(-2) sensitivity and 20-nM detection limit (S/N = 3). The DA substrate yielded the best biosensing performance, as compared with aniline, o-phenylenediamine, or o-aminophenol as the substrate for similar Lac-catalyzed polymerization. Casting the aqueous mixture of DA, glucose oxidase (GOx), Lac, and MWCNTs on a Pt electrode yielded a robust PDA-GOx-Lac-MWCNTs/Pt electrode that exhibits glucose-detection sensitivity of 68.6 microA mM(-1) cm(-2). In addition, 2,2'-azinobis (3-ethylbenzothiazoline-6-sulfonate) diammonium salt (ABTS) was also coimmobilized to yield a PDA-Lac-MWCNTs-ABTS/GCE that can effectively catalyze the reduction of O(2), and it was successfully used as the biocathode of a membraneless glucose/O(2) biofuel cell (BFC) in pH 5.0 Britton-Robinson buffer. The proposed biomacromolecule-immobilization platform based on enzyme-catalyzed polymerization may be useful for preparing many other multifunctional polymeric bionanocomposites for wide applications.

Polymeric redox-responsive delivery systems bearing ammonium salts cross-linked via disulfides

Directory of Open Access Journals (Sweden)

Christian Dollendorf

2013-08-01

Full Text Available A redox-responsive polycationic system was synthesized via copolymerization of N,N-diethylacrylamide (DEAAm and 2-(dimethylaminoethyl methacrylate (DMAEMA. N,N’-bis(4-chlorobutanoylcystamine was used as disulfide-containing cross-linker to form networks by the quaternization of tertiary amine groups. The insoluble cationic hydrogels become soluble by reduction of disulfide to mercaptanes by use of dithiothreitol (DTT, tris(2-carboxyethylphosphine (TCEP or cysteamine, respectively. The soluble polymeric system can be cross-linked again by using oxygen or hydrogen peroxide under basic conditions. The redox-responsive polymer networks can be used for molecular inclusion and controlled release. As an example, phenolphthalein, methylene blue and reactive orange 16 were included into the network. After treatment with DTT a release of the dye could be recognized. Physical properties of the cross-linked materials, e.g., glass transition temperature (Tg, swelling behavior and cloud points (Tc were investigated. Redox-responsive behavior was further analyzed by rheological measurements.

Radiation polymerization of 2-hydroxyethyl methacrylate-vinyl pyrrolidone-water system

International Nuclear Information System (INIS)

Kumakura, M.; Kaetsu, I.

1988-01-01

Polymerization was studied using mixtures of 2-hydroxyethyl methacrylate(HEMA)-water, vinyl pyrrolidone(NVP)-water and 2-hydroxyethyl methacrylate-vinyl pyrrolidone-water. The mixtures were irradiated with gamma radiation from a 60 Co source. Irradiation was carried out at temperatures of 0, -24, -45, -63, -78, and -196 degC. The dependence was studied of the polymerization rate on temperature during irradiation for the individual mixtures, as were the effect of monomer composition on the polymerization of the HEMA-NVP-water system at 0 degC, the effect of water on NVP polymerization and the relationship between water absorption and the composition of the monomer. (E.S.). 4 figs., 6 refs

49 CFR 173.221 - Polymeric beads, expandable and Plastic molding compound.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Polymeric beads, expandable and Plastic molding... Than Class 1 and Class 7 § 173.221 Polymeric beads, expandable and Plastic molding compound. (a) Non-bulk shipments of Polymeric beads (or granules), expandable, evolving flammable vapor and Plastic...

TRANSITION METAL CATALYSIS IN CONTROLLED RADICAL POLYMERIZATION: ATOM TRANSFER RADICAL POLYMERIZATION. (R826735)

Science.gov (United States)

Novel and diversified macromolecular structures, which include polymers with designed topologies (top), compostions (middle), and functionalities (bottom), can be prepared by atom transfer radical polymerization processes. These polymers can be synthesized from a large variety of...

Kinetic advantages of using microwaves in the emulsion polymerization of MMA

Energy Technology Data Exchange (ETDEWEB)

Costa, C. [Departamento de Engenharia Quimica, Universidade Federal de Santa Catarina, Campus Universitario, CEP: 88040-900, Florianopolis, SC (Brazil); Santos, A.F.; Fortuny, M. [Programa de Mestrado em Engenharia de Processos, Universidade Tiradentes, Instituto de Tecnologia e Pesquisa, Av. Murilo Dantas, 300, CEP: 49032-490, Aracaju, SE (Brazil); Araujo, P.H.H. [Departamento de Engenharia Quimica, Universidade Federal de Santa Catarina, Campus Universitario, CEP: 88040-900, Florianopolis, SC (Brazil); Sayer, C. [Departamento de Engenharia Quimica, Universidade Federal de Santa Catarina, Campus Universitario, CEP: 88040-900, Florianopolis, SC (Brazil)], E-mail: csayer@enq.ufsc.br

2009-03-01

Microwave irradiation has been an interesting alternative for heating systems and several chemical reactions. In polymerization processes, microwaves can enhance reaction rates or improve specific characteristics of the formed polymer. In this work, the use of microwave irradiation in emulsion polymerization reactions has been studied, using a commercial microwave reactor, which is able to perform syntheses under controlled conditions of temperature and power. Methyl methacrylate emulsion polymerization reactions were faster, resulting in smaller polymer particles, in comparison to the conventional heating method (reactions in a jacketed reactor). Different effects were observed in the emulsion polymerization of butyl acrylate. To study the effect of high power microwave irradiation upon the emulsion polymerization, a pulsed irradiation strategy was developed, in which the samples were repeatedly heated within short intervals of time (about 27 s) at the maximum microwave power. A significant reduction of the total time of irradiation was observed in reactions carried out under the pulsed scheme, showing the kinetic advantages of using microwaves in emulsion polymerization processes.

Preparation of poly (alkylcyanoacrylate) nanoparticles by polymerization of water-free microemulsions

DEFF Research Database (Denmark)

Krauel, Karen; Graf, Anja; Hook, Sarah M

2006-01-01

designated as droplet, bicontinuous or solution type microemulsions using conductivity, viscosity and self-diffusion NMR. Nanoparticles were prepared by polymerization of selected microemulsions with ethyl-2-cyanoacrylate and the morphology of the particles was investigated. Addition of monomer to all types...... that polymerization is expected to occur at a water-oil interface by base-catalysed polymerization. It would appear that propylene glycol is sufficiently nucleophilic to initiate the polymerization. The use of water-free microemulsions as templates for the preparation of poly (alkylcyanoacrylate) nanoparticles opens...

Polymeric matrix materials for infrared metamaterials

Science.gov (United States)

Dirk, Shawn M; Rasberry, Roger D; Rahimian, Kamyar

2014-04-22

A polymeric matrix material exhibits low loss at optical frequencies and facilitates the fabrication of all-dielectric metamaterials. The low-loss polymeric matrix material can be synthesized by providing an unsaturated polymer, comprising double or triple bonds; partially hydrogenating the unsaturated polymer; depositing a film of the partially hydrogenated polymer and a crosslinker on a substrate; and photopatterning the film by exposing the film to ultraviolet light through a patterning mask, thereby cross-linking at least some of the remaining unsaturated groups of the partially hydrogenated polymer in the exposed portions.

Study of radiation-induced polymerization of vinyl monomers adsorbed on inorganic substances. VIII. Polymerization of styrene and methyl methacrylate adsorbed on aerosil

International Nuclear Information System (INIS)

Fukano, K.; Kageyama, E.

1976-01-01

Aerosol is silica having a purity which is very high compared with that of silica gel and having, unlike silica gel, no micropores. To investigate the effects of impurities and micropores on the radiation-induced polymerization of styrene and methyl methacrylate adsorbed on silica gel, the radiation-induced polymerization of styrene and methyl methacrylate adsorbed on Aerosil was carried out. The results of both the styrene--Aerosil 300 system and the methyl methacrylate--Aerosil 300 system were similar to those of the styrene-silica gel and methyl methacrylate-silica gel systems, respectively. This suggests that in the radiation-induced polymerization of both styrene--silica gel and methyl methacrylate--silica gel systems the impurities and the presence of micropores have almost no effect on the reaction mechanism. The effect of aluminum as an impurity was investigated on the styrene--Aerosil MOX 170 system. It was found that aluminum accelerated the cationic polymerization

Biophysical elucidation of the mechanism of enhanced drug release and topical delivery from polymeric film-forming systems.

Science.gov (United States)

Garvie-Cook, Hazel; Frederiksen, Kit; Petersson, Karsten; Guy, Richard H; Gordeev, Sergey N

2015-08-28

The effect of incorporating the lipidic medium-chain triglyceride (MCT) into polymeric film-forming systems (FFS) for topical drug delivery has been evaluated. First, the in vitro release of betamethasone-17-valerate (BMV), a representative dermatological drug, was determined from FFS comprising either hydrophobic polyacrylate co-polymers, or hydrophilic hydroxypropyl cellulose, with and without MCT. Release was enhanced from both polymers in the presence of MCT. Atomic force microscopy imaging and nanoindentation of FFS with MCT revealed two-phase structured films with softer inclusions (0.5 to 4μm in diameter) surrounded by a more rigid structure. Chemical mapping with Raman micro-spectroscopy showed that MCT was primarily confined to the inclusions within the polymer, which predominated in the surrounding film. BMV was distributed throughout the film but was more concentrated outside the inclusions. Furthermore, while BMV dissolved better into the hydrophobic films, it was more soluble in the MCT inclusions in hydrophilic films, suggesting its increased availability for diffusion from these softer regions of the polymer and explaining the release enhancement observed. Second, ex vivo skin penetration studies clearly revealed that uptake of BMV was higher from hydrophobic FFS than that from the more hydrophilic polymer due, at least in part, to the superior anti-nucleation efficiency of the former. Drug was quickly taken up into the SC from which it then diffused continuously over a sustained period into the lower, viable skin layers. In the presence of MCT, the overall uptake of BMV was increased and provides the basis for further optimisation of FFS as simple, convenient and sustained formulations for topical therapy. Copyright © 2015 Elsevier B.V. All rights reserved.

The clinical usefulness evaluation of normal saline injection in coronary artery computed tomography angiography (Coronary CTA)

International Nuclear Information System (INIS)

Jung, Kang Kyo; Lee, Mi Hwa; Cho, Pyong Kon

2014-01-01

The purpose of this study is that in coronary artery angiography computed tomography (coronary CTA), to gain high quality of image and to use low dose radiation by administrating normal saline and converting the mode of scanning heart rate (HR) characteristics before infusing contrast media. All patients data (total specimens: 200, male: 108, female: 92) were measured by using appropriate mode of scanning the heart rate (HR) after injection of saline. in addition we measured radiation dose (CTDIvol, effective dose) in all examinations. CT number and noise, and blurring of coronary artery (proximal RCA, middle RCA, proximal LCA) were measured and compared. The result of this study after injection of saline, mean heart rate was decreased about 4.8±0.3 bpm (beats per minute). 33 patients (13%) got converting scan mode due to reducing heart rate (HR). In prospective gating mode, radiation dose were measured less 6.0±1.0 mSv (54.1%) than retrospective gating mode. Also showed a significant difference in heart rate decrease in image evaluation

The clinical usefulness evaluation of normal saline injection in coronary artery computed tomography angiography (Coronary CTA)

Energy Technology Data Exchange (ETDEWEB)

Jung, Kang Kyo; Lee, Mi Hwa; Cho, Pyong Kon [Dept. of Radiological Science, Catholic University of Daegu, Daegu (Korea, Republic of)

2014-12-15

The purpose of this study is that in coronary artery angiography computed tomography (coronary CTA), to gain high quality of image and to use low dose radiation by administrating normal saline and converting the mode of scanning heart rate (HR) characteristics before infusing contrast media. All patients data (total specimens: 200, male: 108, female: 92) were measured by using appropriate mode of scanning the heart rate (HR) after injection of saline. in addition we measured radiation dose (CTDIvol, effective dose) in all examinations. CT number and noise, and blurring of coronary artery (proximal RCA, middle RCA, proximal LCA) were measured and compared. The result of this study after injection of saline, mean heart rate was decreased about 4.8±0.3 bpm (beats per minute). 33 patients (13%) got converting scan mode due to reducing heart rate (HR). In prospective gating mode, radiation dose were measured less 6.0±1.0 mSv (54.1%) than retrospective gating mode. Also showed a significant difference in heart rate decrease in image evaluation.

The use of radiation-induced graft polymerization for obtaining polymeric biomaterial on the basis of preparation 'Piyavit'

International Nuclear Information System (INIS)

Kudryavtsev, V.N.; Degtyareva, T.V.; Kabanov, V.Ya.

1998-01-01

The purpose of the present study is to obtain hemocompatible polymeric materials. The method of modification of polymer surface have been elaborated using the radiation-induced graft polymerization after which the surface is capable of coupling with the biologically active substances (BAS) produced from the medicinal leeches. At the Biological Department of Lomonosov Moscow State University was created a medicinal preparation 'Piyavit' isolated from the salivary glands secretion of the medicinal leeches (Hirudo medicinalis). It possess a wide spectrum of biological action on the human organism thanks to the presence of an unique complex natural of BAS (enzymes, inhibitors of proteolityc ensymes, prostanoids and et. al) guaranteed the anticoagulating, thrombolytic, antithrombotic, antiphlogistic, antiatherosclerotic, hypotentic effects and et al.. It has several advantages over anticoagulant heparin which is widely used for above mentioned purpose. 'Piyavit' is the multifunctional preparation, has not negative side-effects and is more cheap. The method of obtaining biocompatible polymers (basically polyethylene) with immobilized 'Piyavit' consist of three stages: 1. The modification of polymer surface by the radiation-induced graft polymerization of acrylic acid to obtain grafted chains polyacrylic acid (PAA) with controlled number and length. 2. The treatment of radiation grafted PAA by thionyl chloride that lead to conversion carboxyl groups of PAA in highly reactive acide chloride groups. 3. The covalent immobilization BAS of 'Piyavit' by acylation amino- and hydroxy-groups (functional groups in BAS) by acide chloride of PAA grafted on the polymere. (author)

Characterization of polymeric microneedle arrays for transdermal drug delivery.

Directory of Open Access Journals (Sweden)

Yusuf K Demir

Full Text Available Microfabrication of dissolvable, swellable, and biodegradable polymeric microneedle arrays (MNs were extensively investigated based in a nano sensitive fabrication style known as micromilling that is then combined with conventional micromolding technique. The aim of this study was to describe the polymer selection, and optimize formulation compounding parameters for various polymeric MNs. Inverse replication of micromilled master MNs reproduced with polydimethylsiloxane (PDMS, where solid out of plane polymeric MNs were subsequently assembled, and physicochemically characterized. Dissolvable, swellable, and biodegradable MNs were constructed to depth of less than 1 mm with an aspect ratio of 3.6, and 1/2 mm of both inter needle tip and base spacing. Micromolding step also enabled to replicate the MNs very precisely and accurate. Polymeric microneedles (MN precision was ranging from ± 0.18 to ± 1.82% for microneedle height, ± 0.45 to ± 1.42% for base diameter, and ± 0.22 to ± 0.95% for interbase spacing. Although dissolvable sodium alginate MN showed less physical robustness than biodegradable polylactic-co-glycolic acid MN, their thermogravimetric analysis is of promise for constructing these polymeric types of matrix devices.

Neutral Polymeric Micelles for RNA Delivery

Science.gov (United States)

Lundy, Brittany B.; Convertine, Anthony; Miteva, Martina; Stayton, Patrick S.

2013-01-01

RNA interference (RNAi) drugs have significant therapeutic potential but delivery systems with appropriate efficacy and toxicity profiles are still needed. Here, we describe a neutral, ampholytic polymeric delivery system based on conjugatable diblock polymer micelles. The diblock copolymer contains a hydrophilic poly[N-(2-hydroxypropyl) methacrylamide-co-N-(2-(pyridin-2- yldisulfanyl)ethyl)methacrylamide) (poly[HPMA-co-PDSMA]) segment to promote aqueous stability and facilitate thiol-disulfide exchange reactions, and a second ampholytic block composed of propyl acrylic acid (PAA), dimethylaminoethyl methacrylate (DMAEMA), and butyl methacrylate (BMA). The poly[(HPMA-co-PDSMA)-b-(PAA-co-DMAEMA-co-BMA)] was synthesized using Reversible Addition-Fragmentation chain Transfer (RAFT) polymerization with an overall molecular weight of 22,000 g/mol and a PDI of 1.88. Dynamic light scattering and fluorescence measurements indicated that the diblock copolymers self-assemble under aqueous conditions to form polymeric micelles with a hydrodynamic radius and critical micelle concentration of 25 nm and 25 μg/mL respectively. Red blood cell hemolysis experiments show that the neutral hydrophilic micelles have potent membrane destabilizing activity at endosomal pH values. Thiolated siRNA targeting glyceraldehyde 3-phosphate dehydrogenase (GAPDH) was directly conjugated to the polymeric micelles via thiol exchange reactions with the pyridal disulfide groups present in the micelle corona. Maximum silencing activity in HeLa cells was observed at a 1:10 molar ratio of siRNA to polymer following a 48 h incubation period. Under these conditions 90 % mRNA knockdown and 65 % and protein knockdown of at 48 h was achieved with negligible toxicity. In contrast the polymeric micelles lacking a pH-responsive endosomalytic segment demonstrated negligible mRNA and protein knockdown under these conditions. The potent mRNA knockdown and excellent biocompatibility of the neutral siRNA conjugates

Metal-catalyzed living radical polymerization and radical polyaddition for precision polymer synthesis

Energy Technology Data Exchange (ETDEWEB)

Mizutani, M; Satoh, K [Department of Applied Chemistry, Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Kamigaito, M, E-mail: kamigait@apchem.nagoya-u.ac.j

2009-08-01

The metal-catalyzed radical addition reaction can be evolved into two different polymerization mechanisms, i.e.; chain- and step-growth polymerizations, while both the polymerizations are based on the same metal-catalyzed radical formation reaction. The former is a widely employed metal-catalyzed living radical polymerization or atom transfer radical polymerization of common vinyl monomers, and the latter is a novel metal-catalyzed radical polyaddition of designed monomer with an unconjugated C=C double bond and a reactive C-Cl bond in one molecule. The simultaneous ruthenium-catalyzed living radical polymerization of methyl acrylate and radical polyaddition of 3-butenyl 2-chloropropionate was achieved with Ru(Cp*)Cl(PPh{sub 3}){sub 2} to afford the controlled polymers, in which the homopolymer segments with the controlled chain length were connected by the ester linkage.

Polyaniline-coated halloysite nanotubes via in-situ chemical polymerization

Energy Technology Data Exchange (ETDEWEB)

Zhang Long [State Key Laboratory of Applied Organic Chemistry and Institute of Polymer Science and Engineering, College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China); Wang Tingmei [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Liu Peng [State Key Laboratory of Applied Organic Chemistry and Institute of Polymer Science and Engineering, College of Chemistry and Chemical Engineering, Lanzhou University, Lanzhou 730000 (China)], E-mail: pliu@lzu.edu.cn

2008-12-30

Polyaniline coated halloysite nanotubes (PANI/HNTs) were prepared by the in-situ soapless emulsion polymerization of the anilinium chloride adsorbed halloysite nanotubes (HNTs), obtained by the dispersion of HNTs in acidic aqueous solution of aniline with magnetic stirring and ultrasonic irradiation, by using ammonium persulfate (APS) as oxidant. The effect of the acidities of the polymerizing media on the crystal structure of the nanotubes was investigated with X-ray diffraction (XRD) technique. The surface conducting coatings of the hybrids were characterized with X-ray photoelectron spectroscopy (XPS). The morphological analyses showed that the polyaniline coated halloysite nanotubes via the in-situ chemical oxidation polymerization with ultrasonic irradiation had the better well-defined structures, by the transmission electron microscopy (TEM). The conductivities of the PANI/HNTs hybrids increased with the increasing of the amounts of HCl dopant added in the emulsion polymerization.

Polyaniline-coated halloysite nanotubes via in-situ chemical polymerization

International Nuclear Information System (INIS)

Zhang Long; Wang Tingmei; Liu Peng

2008-01-01

Polyaniline coated halloysite nanotubes (PANI/HNTs) were prepared by the in-situ soapless emulsion polymerization of the anilinium chloride adsorbed halloysite nanotubes (HNTs), obtained by the dispersion of HNTs in acidic aqueous solution of aniline with magnetic stirring and ultrasonic irradiation, by using ammonium persulfate (APS) as oxidant. The effect of the acidities of the polymerizing media on the crystal structure of the nanotubes was investigated with X-ray diffraction (XRD) technique. The surface conducting coatings of the hybrids were characterized with X-ray photoelectron spectroscopy (XPS). The morphological analyses showed that the polyaniline coated halloysite nanotubes via the in-situ chemical oxidation polymerization with ultrasonic irradiation had the better well-defined structures, by the transmission electron microscopy (TEM). The conductivities of the PANI/HNTs hybrids increased with the increasing of the amounts of HCl dopant added in the emulsion polymerization.

The Morphology of Emulsion Polymerized Latex Particles

Science.gov (United States)

Wignall, G. D.; Ramakrishnan, V. R.; Linne, M. A.; Klein, A.; Sperling, L. H.; Wai, M. P.; Gelman, R. A.; Fatica, M. G.; Hoerl, R. H.; Fisher, L. W.

1987-11-01

Under monomer starved feed conditions, emulsion polymerization of perdeuterated methyl methacrylate and styrene in the presence of preformed polymethylmethacrylate latexes resulted in particles with a core-shell morphology, as determined by small-angle neutron scattering (SANS) analysis for a hollow sphere. The locus of polymerization of the added deuterated monomer is therefore at the particle surface. In similar measurements a statistical copolymer of styrene and methyl methacrylate was used as seed particles for further polymerization of trideuteromethyl methacrylate. The resulting polymer latex was again shown to have a core-shell morphological structure as determined by SANS. SANS experiments were also undertaken on polystyrene latexes polymerized by equilibrium swelling methods, with deuterated polymer forming the first or second step. The experiments covered a molecular weight range of 6 x 10{sup 4} 10{sup 6} the molecular weights are consistent with the experimental errors, indicating that the deuterium labeled molecules are randomly distributed in the latex. These results led to the finding that the polymer chains were constrained in the latex particles by factors of 2 to 4 from the relaxed coil dimensions. For M molecules. Several models were examined, including the possible development of core-shell structures at lower molecular weights.

Synthesis of Amphiphilic Copolymwers by Atom Transfer Radical Polymerization

DEFF Research Database (Denmark)

Hansen, Natanya Majbritt Louie

2007-01-01

Fluorerede polymerer besidder en række enestående egenskaber såsom god biokom-patibilitet og lav overfladeenergi såvel som god kemisk og termisk stabilitet. Målsæt-ningen for denne afhandling var at fremstille fluorerede polymerer og copolymerer, der potentielt kunne finde anvendelse som...... egenskaber der genfindes i homopolymerer af den dominerende monomer i copolymeren. Som indikation af de nye materialers mulige vekselvirkning med omgivelserne udførtes omfattende studier af kontaktvinkler. Film fremstillet af de fluorerede copolymerer og polymerer udviste øget hydrofobicitet (vandafvisning...

Immobilization of biocatalysts for enzymatic polymerizations : Possibilities, advantages, applications

NARCIS (Netherlands)

Miletic, Nemanja; Nastasovic, Aleksandra; Loos, Katja; Miletić, Nemanja; Nastasović, Aleksandra

Biotechnology also holds tremendous opportunities for realizing functional polymeric materials. Biocatalytic pathways to polymeric materials are an emerging research area with not only enormous scientific and technological promise, but also a tremendous impact on environmental issues. Many of the

Photocontrol in Complex Polymeric Materials: Fact or Illusion?

Science.gov (United States)

Jerca, Valentin Victor; Hoogenboom, Richard

2018-06-04

Photoswitches: Exciting recent progress realized in the field of light-controlled polymeric materials is highlighted. It is discussed how the rational choice of azobenzene molecules and their incorporation into complex materials by making use of physical interactions can lead to genuine photocontrollable polymeric systems. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Study on the effects of temperature, time and policy of pre polymerization on particle morphology in propylene slurry polymerization with heterogeneous ziegler-Natta catalysts

International Nuclear Information System (INIS)

Pircheraghi, G.; Pourmahdian, S.; Vatankhah, M.

2008-01-01

The effects of temperature, time and the strategy of pre polymerization were studied on the morphology of polypropylene particles. Propylene polymerization was carried out in slurry phase using fourth generation of Ziegler-Natta Catalyst, cyclohexylmethyl dimethoxysilane as external electron donor, and triethyl aluminum as co-catalyst. Pre polymerizations were carried out based on two strategies: isothermal and non-isothermal conditions. Particle imaging using SEM, bulk density, and particle size distribution was used to analyse the particle morphology. It was found that the variation of initial condition together with the change in the mechanism of particle fracture has a dominant effect on particle morphology. Each combination between the temperature and reaction time causes to have a special effect on the product particle morphology. It has become clear that in isothermal pre polymerization, spherical particles with identical properties were produced. In low temperature experiments particles with porous surface were observed. At increasing temperature, however, the pores disappeared. Non-isothermal pre polymerization produced different morphological types. In all experiments core shell structures were observed that seemed to be related to the structure of catalysts

In situ and real-time small-angle neutron scattering studies of living anionic polymerization process and polymerization-induced self-assembly of block copolymers

International Nuclear Information System (INIS)

Tanaka, H.; Yamauchi, K.; Hasegawa, H.; Miyamoto, N.; Koizumi, S.; Hashimoto, T.

2006-01-01

We have studied a simultaneous living anionic polymerization process of isoprene and deuterated styrene in deuterated benzene with sec-buthyl lithium as an initiator into polyisoprene-block-poly(styrene-d 8 ) and the polymerization-induced self-assembling process. This polymerization-induced self-assembling process was directly observed by an in situ and real-time small-angle neutron scattering (SANS) experiment. The time-resolved SANS studies enabled us to explore a time evolution of hierarchical structures induced by a time evolution of the primary structure (linear sequential connection of two monomers)

Biodegradable Polyelectrolyte Obtained by Radiation Polymerization

International Nuclear Information System (INIS)

Craciun, G.; Martin, D.; Manaila, E.; Nemtanu, M.; Brasoveanu, M.; Ighigeanu, D.

2009-01-01

Poly electrolytes are water-soluble polymers carrying ionic charge along the polymer chain. Depending upon the charge, these polymers are anionic or cationic. The inherent solid - liquid separating efficiency makes these poly electrolytes a unique class of polymers which find extensive application in potable water, industrial raw and process water, municipal sewage treatment, mineral processing and metallurgy, oil drilling and recovery, etc. Also, due to their ability to produce advanced induced coagulation, a considerable amount of bacteria and viruses are precipitated together with the suspended solids. Especially the acrylamide polymers are very efficacious for water treatment but acrylamide is a toxic monomer and therefore their use are governed by international standards that provide the residual acrylamide monomer content (RAMC) in them be less than 0.05%. Under these circumstances our attention was focused on the following research steps that are presented in this paper: 1) Preparation of a special class of poly electrolytes, named Pn, with very low RAMC values, based on electron beam (EB), microwave (MW) and EB + MW induced co-polymerization of aqueous solutions containing appropriate mixtures of acrylamide (AMD) and acrylic acid (AA) monomers (AMD - AA co-polymers). The Pn were obtained by radiation technology with very small RAMC (under 0.01%) as well as in a wide range of molecular weights and charge densities. Very low AMD monomer content of Pn is due to the major advantages of radiation induced polymerization in aqueous solution containing monomers. Due to water presence in the EB irradiated system, irradiated water radicals facilitate the polymerization process and increase rate and level of monomers conversion in co-polymers. Also, once again, by the presence of water, which absorbs MW energy very strongly, the MW polymerization reaction rate is much enhanced resulting in a reaction time about 50-100 times lowers than by conventional heating. Also

Optimization of low-dose protocol in thoracic aorta CTA: weighting of adaptive statistical iterative reconstruction (ASIR) algorithm and scanning parameters

International Nuclear Information System (INIS)

Zhao Yongxia; Chang Jin; Zuo Ziwei; Zhang Changda; Zhang Tianle

2014-01-01

Objective: To investigate the best weighting of adaptive statistical iterative reconstruction (ASIR) algorithm and optimized low-dose scanning parameters in thoracic aorta CT angiography(CTA). Methods: Totally 120 patients with the body mass index (BMI) of 19-24 were randomly divided into 6 groups. All patients underwent thoracic aorta CTA with a GE Discovery CT 750 HD scanner (ranging from 290-330 mm). The default parameters (100 kV, 240 mAs) were applied in Group 1. Reconstructions were performed with different weightings of ASIR(10%-100% with 10%), and the signal to noise ratio (S/N) and contrast to noise ratio(C/N) of images were calculated. The images of series were evaluated by 2 independent radiologists with 5-point-scale and lastly the best weighting were revealed. Then the mAs in Group 2-6 were defined as 210, 180, 150, 120 and 90 with the kilovoltage 100. The CTDI_v_o_l and DLP in every scan series were recorded and the effective dose (E) was calculated. The S/N and C/N were calculated and the image quality was assessed by two radiologists. Results: The best weighing of ASIR was 60% at the 100 kV, 240 mAs. Under 60% of ASIR and 100 kV, the scores of image quality from 240 mAs to 90 mAs were (4.78±0.30)-(3.15±0.23). The CTDI_v_o_l and DLP were 12.64-4.41 mGy and 331.81-128.27 mGy, and the E was 4.98-1.92 mSv. The image qualities among Group 1-5 were nor significantly different (F = 5.365, P > 0.05), but the CTDI_v_o_l and DLP of Group 5 were reduced by 37.0% and 36.9%, respectively compared with Group 1. Conclusions: In thoracic aorta CT Angiography, the best weighting of ASIR is 60%, and 120 mAs is the best mAs with 100 kV in patients with BMI 19-24. (authors)

Synthesis of polystyrene with high melting temperature through BDE/CuCl catalyzed polymerization

Institute of Scientific and Technical Information of China (English)

WAN; Xiaolong

2001-01-01

［1］Ewen, J. A., Novel method for plastic production, Science (in Chinese), 1997, 9: 34.［2］Brintzinger, H. H., Fischer, D., Waymouth, R. M. et al., Stereospecific olefin polymerization with chiral metallocene catalysts, Angewandte Chemie International Edition in English, 1995, 34(11): 1143.［3］Matyjaszewski, K., Atom transfer radical polymerization, role of various components and reaction conditions, Polym. Prep., 1997, 38(2): 736.［4］Wang, J. S., Matyjaszewski, K., Controlled/"living" radical polymerization, atom transfer radical polymerization in the presence of transition-metal complex, J. Am. Soc., 1995, 117: 5614.［5］Wang, J. S., Matyjaszewski, K., Controlled/"living" radical polymerization, halogen atom transfer radical polymerization promoted by a Cu(I)/Cu(II) redox process, Macromolecules, 1995, 28: 7901.［6］Koto, M., Kamigaito, M., Sawamoto, M. et al., Polymerization of methyl methacrylate with the carbon tetrachloride/dichloro-tris(triphenyphosphine) ruthenium(II)/methylaluminum bis(2,6-di-tert-butylphenoxide) initiating system: possible of living radical polymerization, Macromolecules, 1995, 28: 1721.［7］Ando, T., Kato, M., Living radical polymerization of methyl methacrylate with Ruthenium complex: formation of polymers with controlled molecular weights and very narrow distributions, Macromolecules, 1996, 29: 1070.［8］Granel, C., Dubios, P., Jerome, R. et al., Controlled radical polymerization of methacrylic monomers in the presence of a bis(ortho-chelated) arylnickel(II) complex and different activated alkyl halides, Macromolecules, 1996, 29: 8576.［9］Granel, C., Moineau, G., Lecome, P. et al., (Meth)acrylates pseudo-living radical polymerization in the presence of transition metal complexes: the kharasch reaction revisited, Polym. Prep., 1997, 38(1): 450.［10］Ando, T., Kamigaito, M., Sawamoto, M., Iron(II) chloride complex for living radical polymerization of methyl methacrylate, Macromolecules, 1997, 30: 4507.［11�

Interfacial adhesion and superhydrophobicity modulated with polymeric nanopillars using integrated nanolithography

International Nuclear Information System (INIS)

Yang, Zong-Han; Kuo, Chiung-Wen; Chueh, Di-Yan; Tung, Yi-Chung; Chen, Peilin; Chien, Fan-Ching

2012-01-01

This paper reports the successful fabrication of flexible replicas with polymeric nanopillars using a process that combines nanosphere lithography, dry deep etching, soft-lithography, nanomolding and hydrophobic modification. The polymeric nanopillars with various sizes and three different periodicities have been implemented for systematic investigations on the interfacial properties on those surfaces. Such a flexible polymeric surface exhibited the maximum static contact angle of 166.8° at the nanopillars with a diameter of 60 nm, height of 710 nm and periodicity of 300 nm. The optimum aspect ratio should be less than 7 to avoid defects and collapses among those polymeric nanopillars during nanomolding. Metastable contact at the transition state indeed occurred on the parts of the intrinsic nanopillars, the experimental results of which also matched well to the classical theory of critical contact angle. Using hydrophobic modifications, metastable contacts among those polymeric nanopillars have further been eliminated. The polymeric nanopillars reported here were verified as having very strong adhesion as well as superhydrophobicity because such nanopillars made microdroplets hang firmly on the vertical surfaces of those designed replicas. (paper)

Carotid artery stenosis: Performance of advanced vessel analysis software in evaluating CTA

International Nuclear Information System (INIS)

Tsiflikas, Ilias; Biermann, Christina; Thomas, Christoph; Ketelsen, Dominik; Claussen, Claus D.; Heuschmid, Martin

2012-01-01

Objectives: The aim of this study was to evaluate time efficiency and diagnostic reproducibility of an advanced vessel analysis software for diagnosis of carotid artery stenosis. Material and methods: 40 patients with suspected carotid artery stenosis received head and neck DE-CTA as part of their pre-interventional workup. Acquired data were evaluated by 2 independent radiologists. Stenosis grading was performed by MPR eyeballing with freely adjustable MPRs and with a preliminary prototype of the meanwhile available client-server and advanced visualization software syngo.via CT Vascular (Siemens Healthcare, Erlangen, Germany). Stenoses were graded according to the following 5 categories: I: 0%, II: 1–50%, III: 51–69%, IV: 70–99% and V: total occlusion. Furthermore, time to diagnosis for each carotid artery was recorded. Results: Both readers achieved very good specificity values and good respectively very good sensitivity values without significant differences between both reading methods. Furthermore, there was a very good correlation between both readers for both reading methods without significant differences (kappa value: standard image interpretation k = 0.809; advanced vessel analysis software k = 0.863). Using advanced vessel analysis software resulted in a significant time saving (p < 0.0001) for both readers. Time to diagnosis could be decreased by approximately 55%. Conclusions: Advanced vessel analysis application CT Vascular of the new imaging software syngo.via (Siemens Healthcare, Forchheim, Germany) provides a high rate of reproducibility in assessment of carotid artery stenosis. Furthermore a significant time saving in comparison to standard image interpretation is achievable

Carotid artery stenosis: Performance of advanced vessel analysis software in evaluating CTA

Energy Technology Data Exchange (ETDEWEB)

Tsiflikas, Ilias, E-mail: ilias.tsiflikas@med.uni-tuebingen.de [University Hospital of Tuebingen, Diagnostic and Interventional Radiology, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Biermann, Christina, E-mail: christina.biermann@siemens.com [University Hospital of Tuebingen, Diagnostic and Interventional Radiology, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Siemens AG, Siemens Healthcare Consulting, Allee am Röthelheimpark 3A, 91052 Erlangen (Germany); Thomas, Christoph, E-mail: christoph.thomas@med.uni-tuebingen.de [University Hospital of Tuebingen, Diagnostic and Interventional Radiology, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Ketelsen, Dominik, E-mail: dominik.ketelsen@med.uni-tuebingen.de [University Hospital of Tuebingen, Diagnostic and Interventional Radiology, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Claussen, Claus D., E-mail: claus.claussen@med.uni-tuebingen.de [University Hospital of Tuebingen, Diagnostic and Interventional Radiology, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany); Heuschmid, Martin, E-mail: martin.heuschmid@med.uni-tuebingen.de [University Hospital of Tuebingen, Diagnostic and Interventional Radiology, Hoppe-Seyler-Str. 3, 72076 Tuebingen (Germany)

2012-09-15

Objectives: The aim of this study was to evaluate time efficiency and diagnostic reproducibility of an advanced vessel analysis software for diagnosis of carotid artery stenosis. Material and methods: 40 patients with suspected carotid artery stenosis received head and neck DE-CTA as part of their pre-interventional workup. Acquired data were evaluated by 2 independent radiologists. Stenosis grading was performed by MPR eyeballing with freely adjustable MPRs and with a preliminary prototype of the meanwhile available client-server and advanced visualization software syngo.via CT Vascular (Siemens Healthcare, Erlangen, Germany). Stenoses were graded according to the following 5 categories: I: 0%, II: 1–50%, III: 51–69%, IV: 70–99% and V: total occlusion. Furthermore, time to diagnosis for each carotid artery was recorded. Results: Both readers achieved very good specificity values and good respectively very good sensitivity values without significant differences between both reading methods. Furthermore, there was a very good correlation between both readers for both reading methods without significant differences (kappa value: standard image interpretation k = 0.809; advanced vessel analysis software k = 0.863). Using advanced vessel analysis software resulted in a significant time saving (p < 0.0001) for both readers. Time to diagnosis could be decreased by approximately 55%. Conclusions: Advanced vessel analysis application CT Vascular of the new imaging software syngo.via (Siemens Healthcare, Forchheim, Germany) provides a high rate of reproducibility in assessment of carotid artery stenosis. Furthermore a significant time saving in comparison to standard image interpretation is achievable.

electrocatalytic reduction of oxygen at vapor phase polymerized poly ...

African Journals Online (AJOL)

Preferred Customer

ABSTRACT. We successfully polymerized poly(3,4-ethylenedioxidethiophene) by vapor phase polymerization technique on rotating glassy carbon disk electrode. The catalytic activity of this electrode towards oxygen reduction reaction was investigated and showed remarkable activity. Rotating disk voltammetry was used to ...

Propene bulk polymerization kinetics: Role of prepolymerization and hydrogen

NARCIS (Netherlands)

Pater, J.T.M.; Weickert, G.; van Swaaij, Willibrordus Petrus Maria

2003-01-01

An experimental setup for the polymerization of liquid propylene was used to carry out main polymerizations with and without a prepolymerization step. Two types of prepolymerization are introduced: at a constant temperature and at rapidly increasing reactor temperatures. With the present catalyst

Emulsion polymerization with high energy radiation

International Nuclear Information System (INIS)

Stannett, V.T.; Stahel, E.P.

1992-01-01

High energy radiation, particularly that of cobalt-60 or caesium-137 gamma-rays, provides in principle an ideal initiator for emulsion polymerization. The high free radical yields from the radiolysis of the aqueous phase combined with the high kinetic chain lengths associated with emulsion polymerization lead to a highly effective utilization of the radiation. There are other important advantages compared with the use of chemical initiators such as potassium persulfate. These are outlined in the chapter, together with some attendant disadvantages. Radiation-induced initiation is temperature independent, and low temperature polymerizations can be conducted with ease. Monomers that mainly terminate their growing chains by chain transfer to monomer give higher molecular weights at lower temperatures. Industrially, vinyl acetate is an important example of such a monomer, and it has been studied using radiation initiation. Both laboratory and pilot plant studies have been carried out and reported. The results are summarized in this chapter. Styrene is the classical example of a material that under a number of conditions closely obeys the so-called ideal Smith-Ewart kinetics. It has been found that under similar conditions but substituting radiation for potassium persulfate as the initiator, ideal kinetics were closely followed. Most of the conventional and some non-standard vinyl and diene monomers have been studied to some extent with radiation-initiated polymerizations in emulsion. To conserve space however, this chapter presents and discusses the results obtained only with styrene and vinyl acetate, both in laboratory and pilot plant investigations. Other monomers and special situations are referenced either directly or to the other available reviews. (orig.)

Emulsion Polymerization of Etyl Acrylate: The Effect of Surfactant, Initiator Concentration and PolymerizationTechnique on Particle Size Distribution

Directory of Open Access Journals (Sweden)

Nitri Arinda

2009-04-01

Full Text Available Emulsion polymerization was conducted using ethyl acrylate monomer. Theeffect of sodium lauryl sulfate concentration, ammonium persulfate concentration, the various of polymerizationtechniques and feeding time to the conversion, particle size and its distribution were observed. The purpose of thisresearch is to obtain the optimum condition of ethyl acrylate homopolymer with particle size around 100 nm, to get theparticle size distribution monodisperse and to get solid content value of the experiment closed to its theoretical value.The optimum condition then could be applied in shell polymerization of core-shell polymers. The results of the researchshowed that semicontinuous technique obtained optimum sodium lauryl sulfate concentration at 20 CMC (criticalmicelle concentration and ammonium persulfate concentration is 3%. By using batch technique that the biggestparticle size is 123 nm with conversion 95.8% and monodisperse. The shorter of feeding time the more monomer ofethyl acrylate being polymerized, it is showed by the higher conversion up to 94.4% and the bigger particle size is107.9 nm.

Novel polymeric nanocomposites and porous materials prepared using organogels

International Nuclear Information System (INIS)

Lai, Wei-Chi; Tseng, Shen-Chen

2009-01-01

We propose a new method for preparing polymeric nanocomposites and porous materials using self-assembled templates formed by 1,3:2,4-dibenzylidene sorbitol (DBS) organogels. DBS is capable of self-assembling into a 3D nanofibrillar network at relatively low concentrations in some organic solvents to produce organogels. In this study, we induced the formation of such physical cross-linked networks in styrene. Subsequently, we polymerized the styrene in the presence of chemical cross-linkers, divinyl benzene (DVB), with different amounts of DBS using thermal-initiated polymerization. The resulting materials were transparent, homogeneous polystyrene (PS) nanocomposites with both physical and chemical cross-links. The porous polymeric materials were obtained by solvent extraction of the DBS nanofibrils from the PS. Brunauer-Emmett-Teller (BET) measurements show that the amounts of DBS and DVB influenced the specific surface area after the removal of the DBS fibrils.

Novel polymeric nanocomposites and porous materials prepared using organogels

Energy Technology Data Exchange (ETDEWEB)

Lai, Wei-Chi; Tseng, Shen-Chen, E-mail: wclai@mail.tku.edu.t [Department of Chemical and Materials Engineering, Tamkang University, 151 Ying-chuan Road, Tamsui, Taipei 25137, Taiwan (China)

2009-11-25

We propose a new method for preparing polymeric nanocomposites and porous materials using self-assembled templates formed by 1,3:2,4-dibenzylidene sorbitol (DBS) organogels. DBS is capable of self-assembling into a 3D nanofibrillar network at relatively low concentrations in some organic solvents to produce organogels. In this study, we induced the formation of such physical cross-linked networks in styrene. Subsequently, we polymerized the styrene in the presence of chemical cross-linkers, divinyl benzene (DVB), with different amounts of DBS using thermal-initiated polymerization. The resulting materials were transparent, homogeneous polystyrene (PS) nanocomposites with both physical and chemical cross-links. The porous polymeric materials were obtained by solvent extraction of the DBS nanofibrils from the PS. Brunauer-Emmett-Teller (BET) measurements show that the amounts of DBS and DVB influenced the specific surface area after the removal of the DBS fibrils.

The study of polymeric hydro-gels with unique properties obtained by polymerization with gamma radiation processing

International Nuclear Information System (INIS)

Dragusin, M.

1995-01-01

This thesis presents the work carried out on polymeric hydro-gels obtained by radiation processing using 60 Co gamma rays from the irradiation facility IETI-10.000 (10 k Ci), and on the polymeric hydro-gels obtained by irradiation with the electron beams from a linear accelerator (6 MeV). The aim of the study was to determine the effect of the rate dose and total dose absorbed in the materials. There are presented the preparation methods of homo- and co-polymer hydro-gels (acrylics, namely anionic and neutral monomers (acrylamide, acrylic acid, vinyl acetate) and cationic monomers (di-methyl di-allyl ammonium chloride)) such as floculants, additives, absorbers, etc. Concerning with these we have analysed the preparation methods, the mechanical, thermal, diffusivity, and swelling properties of polymeric hydro-gels in a large variety of gels of type I or II. The technological aspects and end use were studied in connection with the characteristics of the radiation processing of these hydro-gels as a function of chemical composition rate and absorbed dose, swelling degree (low and very high hydro-soluble), mechanical and diffusional properties. (author) 33 figs., 12 tabs., 101 refs

Radiation polymerization of tetrafluoroethylene

International Nuclear Information System (INIS)

Kadoi, H.; Lugao, A.B.; Oikawa, H.

1984-01-01

Tetrafluoroethylene (TFE) monomer was obtained by means of the pyrolysis of chlorodifluoromethane (R-22). The experiments were carried out in quartz tube with temperature between 700 0 and 800 0 C. The principal reaction of the pyrolysis is considered to be: 2CHClF2 ----> C 2 F 4 +2HCl. However, by-products such as HF, C 3 F 6 , C 2 HClF 4 , C 4 F 8 etc are also produced in the pyrolysis process. The conversions of R-22 varied from 30 to 50%, depending upon the temperature, pressure and flow rate of R-22 in the furnace. Finally the TFE monomer of purity higher than 99.98% was obtained by fractional distillation in low temperatures ranging from -10 0 to -30 0 C. The bulk polymerization of this monomer induced by γ-rays from 3000Ci cobalt-60 source was studied at various temperatures (room temperature, 0 0 , -23 0 and -78 0 C). The monomers were introduced into stainless steel vessels of 15 and 60 ml volume under vacuum. The control of polymerization reaction was rather hard at temperatures higher than -23 0 C due to the difficulty of removing the heat of reaction. However, the polymerization at -78 0 C was very easy to control. The white polymer particles were obtained in agglomerated state. The IR spectra of the polymers were consistent with those of commercial products. The melting points of samples were between 326 0 and 331 0 C. (Author) [pt

POLYMERIC MATERIALS FOR SOLAR ENERGY UTILIZATION: A COMPARATIVE EXPERIMENTAL STUDY AND ENVIRONMENTAL ASPECTS

Directory of Open Access Journals (Sweden)

Alexander Doroshenko

2016-08-01

Full Text Available Full-scale metal solar collectors and solar collectors fabricated from polymeric materials are studied in present research. Honeycomb multichannel plates made from polycarbonate were chosen to create a polymeric solar collector. Polymeric collector is 67.8% lighter than metal solar collector. It was experimentally shown that the efficiency of a polymeric collector is 7–14% lower than a traditional collector. An ecologically based Life Cycle Assessment showed the advantages of the application of polymeric materials in the construction of solar collectors.

Novel polymer coatings based on plasma polymerized 2-methoxyethyl acrylate

DEFF Research Database (Denmark)

Wu, Zhenning; Jiang, Juan; Benter, Maike

2008-01-01

plasma system[4]. The system named SoftPlasma™ is equipped with unique three-phase pulsed AC voltage. Low energy plasma polymerization has almost no thermal load for sensitive polymer materials[5]. Plasma polymerized coatings are highly cross-linked, pin-hole free and provide hydrophilic or hydrophobic...... properties[4-6]. We have exploited these possibilities and prepared plasma polymerized 2-methoxyethyl acrylate (PPMEA) coatings on various polymer substrates. The PPMEA coatings were optimized using various plasma polymerization conditions and characterized by X-ray photoelectron spectroscopy......, Fouriertransform infrared spectroscopy, Atomic force spectroscopy and Water contact-angle measurements. The microstructures ofPPMEA coatings with different thicknesses were also studied. For practical applications in mind, the coating stability was tested in different media (air, water, acetone, phosphate...

Electrospun polymeric nanofibers for transdermal drug delivery

Directory of Open Access Journals (Sweden)

Mahya Rahmani

2017-04-01

Full Text Available Conventional transdermal drug delivery systems (TDDS have been designed for drug delivery through the skin. These systems use the permeability property of stratum corneum, the outermost surface layer of the skin. Applying polymeric micro and nanofibers in drug delivery has recently attracted great attention and the electrospinning technique is the preferred method for polymeric micro-nanofibers fabrication with a great potential for drug delivery. More studies in the field of nanofibers containing drug are divided two categories: first, preparation and characterization of nanofibers containing drug and second, investigation of their therapeutic applications. Drugs used in electrospun nanofibers can be categorized into three main groups, including antibiotics and antimicrobial agents, anti-inflammatory agents and vitamins with therapeutic applications. In this paper, we review the application of electrospun polymeric scaffolds in TDDS and also introduce several pharmaceutical and therapeutic agents which have been used in polymer nanofibrous patches.

Polymerized and functionalized triglycerides

Science.gov (United States)

Plant oils are useful sustainable raw materials for the development of new chemical products. As part of our research emphasis in sustainability and green polymer chemistry, we have explored a new method for polymerizing epoxidized triglycerides with the use of fluorosulfonic acid. Depending on the ...

A theory for fracture of polymeric gels

Science.gov (United States)

Mao, Yunwei; Anand, Lallit

2018-06-01

A polymeric gel is a cross-linked polymer network swollen with a solvent. If the concentration of the solvent or the deformation is increased to substantial levels, especially in the presence of flaws, then the gel may rupture. Although various theoretical aspects of coupling of fluid permeation with large deformation of polymeric gels are reasonably well-understood and modeled in the literature, the understanding and modeling of the effects of fluid diffusion on the damage and fracture of polymeric gels is still in its infancy. In this paper we formulate a thermodynamically-consistent theory for fracture of polymeric gels - a theory which accounts for the coupled effects of fluid diffusion, large deformations, damage, and also the gradient effects of damage. The particular constitutive equations for fracture of a gel proposed in our paper, contain two essential new ingredients: (i) Our constitutive equation for the change in free energy of a polymer network accounts for not only changes in the entropy, but also changes in the internal energy due the stretching of the Kuhn segments of the polymer chains in the network. (ii) The damage and failure of the polymer network is taken to occur by chain-scission, a process which is driven by the changes in the internal energy of the stretched polymer chains in the network, and not directly by changes in the configurational entropy of the polymer chains. The theory developed in this paper is numerically implemented in an open-source finite element code MOOSE, by writing our own application. Using this simulation capability we report on our study of the fracture of a polymeric gel, and some interesting phenomena which show the importance of the diffusion of the fluid on fracture response of the gel are highlighted.

Anisotropic microporous supports impregnated with polymeric ion-exchange materials

Science.gov (United States)

Friesen, Dwayne; Babcock, Walter C.; Tuttle, Mark

1985-05-07

Novel ion-exchange media are disclosed, the media comprising polymeric anisotropic microporous supports containing polymeric ion-exchange or ion-complexing materials. The supports are anisotropic, having small exterior pores and larger interior pores, and are preferably in the form of beads, fibers and sheets.

Inclusive and semi-inclusive analysis from polarised deep-inelastic muon scattering

International Nuclear Information System (INIS)

Kageya, T.

1999-01-01

We present new results for the spin-dependent structure function on the proton and for the polarised quark distributions in the nucleon from semi-inclusive spin asymmetries. With the inclusive asymmetry from deep inelastic scattering of polarised muons on polarised protons, it is found that the Ellis-Jaffe sum rule is violated. Using our results for Γ d 1 , the Bjorken sum rule is confirmed with an accuracy of about 15%. From semi-inclusive spin asymmetries and SMC inclusive spin asymmetries, we determine the polarised quark distributions of valence u and d quarks to be positive and negative, respectively, while the non-strange sea distribution to be consistent with zero

Influence of CO2 on ultrasound-induced polymerizations in high-pressure fluids

NARCIS (Netherlands)

Kuijpers, M.W.A.; Jacobs, L.J.M.; Kemmere, M.F.; Keurentjes, J.T.F.

2005-01-01

A strong viscosity increase upon polymerization hinders cavitation and subsequent radical formation during an ultrasound-induced bulk polymerization. Ultrasound-induced radical polymerizations of methyl methacrylate (MMA) have been performed in CO2-expanded MMA, as well as in bulk MMA. For this

PPLA-cellulose nanocrystals nanocomposite prepared by in situ polymerization

International Nuclear Information System (INIS)

Paula, Everton L. de; Pereirea, Fabiano V.; Mano, Valdir

2011-01-01

This work reports the preparation and and characterization of a PLLA-cellulose nanocrystals nanocomposite obtained by in situ polymerization. The nanocomposite was prepared by ring opening polymerization of the lactide dimer in the presence of cellulose nanocrystals (CNCs) and the as-obtained materials was characterized using FTIR, DSC, XRD and TGA measurements. The incorporation of cellulose nanocrystals in PLLA using this method improved the thermal stability and increased the crystallinity of PLLA. These results indicate that the incorporation of CNCs by in situ polymerization improve thermal properties and has potential to improve also mechanical properties of this biodegradable polymer. (author)

Optical Properties of the Self-Assembling Polymeric Colloidal Systems

Directory of Open Access Journals (Sweden)

Alexandra Mocanu

2013-01-01

Full Text Available In the last decade, optical materials have gained much interest due to the high number of possible applications involving path or intensity control and filtering of light. The continuous emerging technology in the field of electrooptical devices or medical applications allowed the development of new innovative cost effective processes to obtain optical materials suited for future applications such as hybrid/polymeric solar cells, lasers, polymeric optical fibers, and chemo- and biosensing devices. Considering the above, the aim of this review is to present recent studies in the field of photonic crystals involving the use of polymeric materials.

Tribology of polymeric nanocomposites friction and wear of bulk materials and coatings

CERN Document Server

Friedrich, Klaus

2013-01-01

Tribology of Polymeric Nanocomposites provides a comprehensive description of polymeric nanocomposites, both as bulk materials and as thin surface coatings, and provides rare, focused coverage of their tribological behavior and potential use in tribological applications. Providing engineers and designers with the preparation techniques, friction and wear mechanisms, property information and evaluation methodology needed to select the right polymeric nanocomposites for the job, this unique book also includes valuable real-world examples of polymeric nanocomposites in a

Plasma polymerized high energy density dielectric films for capacitors

Science.gov (United States)

Yamagishi, F. G.

1983-01-01

High energy density polymeric dielectric films were prepared by plasma polymerization of a variety of gaseous monomers. This technique gives thin, reproducible, pinhole free, conformable, adherent, and insoluble coatings and overcomes the processing problems found in the preparation of thin films with bulk polymers. Thus, devices are prepared completely in a vacuum environment. The plasma polymerized films prepared all showed dielectric strengths of greater than 1000 kV/cm and in some cases values of greater than 4000 kV/cm were observed. The dielectric loss of all films was generally less than 1% at frequencies below 10 kHz, but this value increased at higher frequencies. All films were self healing. The dielectric strength was a function of the polymerization technique, whereas the dielectric constant varied with the structure of the starting material. Because of the thin films used (thickness in the submicron range) surface smoothness of the metal electrodes was found to be critical in obtaining high dielectric strengths. High dielectric strength graft copolymers were also prepared. Plasma polymerized ethane was found to be thermally stable up to 150 C in the presence of air and 250 C in the absence of air. No glass transitions were observed for this material.

Preparation of polymer microspheres by radiation-induced polymerization

International Nuclear Information System (INIS)

Naka, Y.; Yamamoto, Y.; Yoshida, Y.; Tagawa, S.

1995-01-01

Cross-liking monomer, diethylene glycol dimethacrylate gives microspheres from organic solution by radiation-induced polymerization. /One of the remarkable result is that the number of the microspheres is not changing during the polymerization. Ethyl methacrylate, maleic anhydride, styrene and acrylamide are used as comonomers. These comonomers give the microspheres in the range of 0 to 0.4 as mol fractions. (author)

Recent advances on polymeric membranes for membrane reactors

KAUST Repository

Buonomenna, M. G.

2012-06-24

Membrane reactors are generally applied in high temperature reactions (>400 °C). In the field of fine chemical synthesis, however, much milder conditions are generally applicable and polymeric membranes were applied without their damage. The successful use of membranes in membrane reactors is primary the result of two developments concerning: (i) membrane materials and (ii) membrane structures. The selection of a suited material and preparation technique depends on the application the membrane is to be used in. In this chapter a review of up to date literature about polymers and configuration catalyst/ membranes used in some recent polymeric membrane reactors is given. The new emerging concept of polymeric microcapsules as catalytic microreactors has been proposed. © 2012 Bentham Science Publishers. All rights reserved.

Metal nanoparticles/ionic liquid/cellulose: polymeric membrane for hydrogenation reactions

Directory of Open Access Journals (Sweden)

Marcos Alexandre Gelesky

2014-01-01

Full Text Available Rhodium and platinum nanoparticles were supported in polymeric membranes with 10, 20 and 40 µm thickness. The polymeric membranes were prepared combining cellulose acetate and the ionic liquid (IL 1-n-butyl-3-methylimidazolium bis(trifluoromethane sulfonylimide (BMI.(NTf2. The presence of metal nanoparticles induced an increase in the polymeric membrane surface areas. The increase of the IL content resulted in an improvement of elasticity and decrease in tenacity and toughness, whereas the stress at break was not affected. The presence of IL probably causes an increase in the separation between the cellulose molecules that result in a higher flexibility and processability of the polymeric membrane. The CA/IL/M(0 combinations exhibit an excellent synergistic effect that enhances the activity and durability of the catalyst for the hydrogenation of cyclohexene. The CA/IL/M(0 polymeric membrane displays higher catalytic activity (up to 7.353 h-1 for the 20 mm of CA/IL/Pt(0 and stability than the nanoparticles dispersed only in the IL.

Inclusive pedagogy

DEFF Research Database (Denmark)

Korsgaard, Morten Timmermann; Skov Mortensen, Stig

This article will present a case for a shift in perspective in inclusive education research towards a continentally inspired approach. Drawing on the age old distinction between continental and Anglo-American educational research the aim is to flesh out what a shift to a continental approach...... will entail, and why it might be beneficial to research in inclusive education...

The effects of polymeric plutonium on erythrocyte survival in mice, (1)

International Nuclear Information System (INIS)

Joshima, Hisamasa; Kashima, Masatoshi; Matsuoka, Osamu

1976-01-01

The changes in erythrocyte counts, hematocrit, hemoglobin, reticulocyte counts and erythrocyte survival following an intravenous injection of polymeric 239 Pu at the dose level of 15 μCi/kg, 10 μCi/kg and 5 μCi/kg were studied in CF no. 1 male mice in order to investigate the possible pathogenesis of anemia produced by irradiation of polymeric plutonium. The administration of 15 μCi/kg and 10 μCi/kg of polymeric plutonium produced anemia but 5 μCi/kg had no significant effect. Studies with 51 Cr labelled erythrocyte showed a moderate reduction in survival of erythrocyte following a single intraveneous injection of polymeric plutonium. Not only the intracorpuscular effect but also extracorpuscular effect of polymeric plutonium was considered to lead to a reduction in erythrocyte survival, but no clear dose relationship could be observed between the reduction of survival and either intracorpuscular effect or extracorpuscular effect. Although the most important pathogenesis of anemia produced by polymeric plutonium is supposed to be a decreased erythropoiesis, it was believed that both qualitatively impaired erythropoiesis and abnormal erythrocyte destruction might also play some role in the occurrence of anemia. (auth.)

Silicoaluminates as “Support Activator” Systems in Olefin Polymerization Processes

Science.gov (United States)

Tabernero, Vanessa; Camejo, Claudimar; Terreros, Pilar; Alba, María Dolores; Cuenca, Tomás

2010-01-01

In this work we report the polymerization behaviour of natural clays (montmorillonites, MMT) as activating supports. These materials have been modified by treatment with different aluminium compounds in order to obtain enriched aluminium clays and to modify the global Brönsted/Lewis acidity. As a consequence, the intrinsic structural properties of the starting materials have been changed. These changes were studied and these new materials used for ethylene polymerization using a zirconocene complex as catalyst. All the systems were shown to be active in ethylene polymerization. The catalyst activity and the dependence on acid strength and textural properties have been also studied. The behaviour of an artificial silica (SBA 15) modified with an aluminium compound to obtain a silicoaluminate has been studied, but no ethylene polymerization activity has been found yet.

Variables and advantages of the polymerization process in plasma

International Nuclear Information System (INIS)

Rojas, Andres F; Ortiz, Jairo A; Restrepo, Elizabeth; Devia Alfonso

1998-01-01

They are given to know the parameters that affect the polymerization process in plasma like they are: the kinetics, the electric joining, the variables related to the substrata and the interaction plasma/surface. Some advantages of the polymerization process are also presented with regard to the conventional processes

Reaction of Acetylenedicarboxylic Acid Made Easy: High-Pressure Route for Polymerization

DEFF Research Database (Denmark)

Delori, Amit; Hutchison, Ian B.; Bull, Craig L.

2018-01-01

A breakthrough has been achieved in improving the efficiency of solid-state polymerization of acetylenedicarboxylic acid (ADCA). Traditional solid-state polymerization of ADCA is marked by long exposure times of γ-radiation (>10 days) and very low yields (around 5.5%). We have been able to perform...... a reaction to an n = 8 oligomer, as confirmed by matrix-assisted laser desorption/ionization-time of flight, in less than 2 min by employing ∼6 GPa of pressure. We have determined the crystal structure of ADCA on increasing pressure to (5.2 GPa) to provide insight into the process of polymerization...... with Pixel calculations supporting our evaluation of the polymerization process....

Large Scale Laser Two-Photon Polymerization Structuring for Fabrication of Artificial Polymeric Scaffolds for Regenerative Medicine

International Nuclear Information System (INIS)

Malinauskas, M.; Purlys, V.; Zukauskas, A.; Rutkauskas, M.; Danilevicius, P.; Paipulas, D.; Bickauskaite, G.; Gadonas, R.; Piskarskas, A.; Bukelskis, L.; Baltriukiene, D.; Bukelskiene, V.; Sirmenis, R.; Gaidukeviciute, A.; Sirvydis, V.

2010-01-01

We present a femtosecond Laser Two-Photon Polymerization (LTPP) system of large scale three-dimensional structuring for applications in tissue engineering. The direct laser writing system enables fabrication of artificial polymeric scaffolds over a large area (up to cm in lateral size) with sub-micrometer resolution which could find practical applications in biomedicine and surgery. Yb:KGW femtosecond laser oscillator (Pharos, Light Conversion. Co. Ltd.) is used as an irradiation source (75 fs, 515 nm (frequency doubled), 80 MHz). The sample is mounted on wide range linear motor driven stages having 10 nm sample positioning resolution (XY--ALS130-100, Z--ALS130-50, Aerotech, Inc.). These stages guarantee an overall travelling range of 100 mm into X and Y directions and 50 mm in Z direction and support the linear scanning speed up to 300 mm/s. By moving the sample three-dimensionally the position of laser focus in the photopolymer is changed and one is able to write complex 3D (three-dimensional) structures. An illumination system and CMOS camera enables online process monitoring. Control of all equipment is automated via custom made computer software ''3D-Poli'' specially designed for LTPP applications. Structures can be imported from computer aided design STereoLihography (stl) files or programmed directly. It can be used for rapid LTPP structuring in various photopolymers (SZ2080, AKRE19, PEG-DA-258) which are known to be suitable for bio-applications. Microstructured scaffolds can be produced on different substrates like glass, plastic and metal. In this paper, we present microfabricated polymeric scaffolds over a large area and growing of adult rabbit myogenic stem cells on them. Obtained results show the polymeric scaffolds to be applicable for cell growth practice. It exhibit potential to use it for artificial pericardium in the experimental model in the future.

Large Scale Laser Two-Photon Polymerization Structuring for Fabrication of Artificial Polymeric Scaffolds for Regenerative Medicine

Science.gov (United States)

Malinauskas, M.; Purlys, V.; Žukauskas, A.; Rutkauskas, M.; Danilevičius, P.; Paipulas, D.; Bičkauskaitė, G.; Bukelskis, L.; Baltriukienė, D.; Širmenis, R.; Gaidukevičiutė, A.; Bukelskienė, V.; Gadonas, R.; Sirvydis, V.; Piskarskas, A.

2010-11-01

We present a femtosecond Laser Two-Photon Polymerization (LTPP) system of large scale three-dimensional structuring for applications in tissue engineering. The direct laser writing system enables fabrication of artificial polymeric scaffolds over a large area (up to cm in lateral size) with sub-micrometer resolution which could find practical applications in biomedicine and surgery. Yb:KGW femtosecond laser oscillator (Pharos, Light Conversion. Co. Ltd.) is used as an irradiation source (75 fs, 515 nm (frequency doubled), 80 MHz). The sample is mounted on wide range linear motor driven stages having 10 nm sample positioning resolution (XY—ALS130-100, Z—ALS130-50, Aerotech, Inc.). These stages guarantee an overall travelling range of 100 mm into X and Y directions and 50 mm in Z direction and support the linear scanning speed up to 300 mm/s. By moving the sample three-dimensionally the position of laser focus in the photopolymer is changed and one is able to write complex 3D (three-dimensional) structures. An illumination system and CMOS camera enables online process monitoring. Control of all equipment is automated via custom made computer software "3D-Poli" specially designed for LTPP applications. Structures can be imported from computer aided design STereoLihography (stl) files or programmed directly. It can be used for rapid LTPP structuring in various photopolymers (SZ2080, AKRE19, PEG-DA-258) which are known to be suitable for bio-applications. Microstructured scaffolds can be produced on different substrates like glass, plastic and metal. In this paper, we present microfabricated polymeric scaffolds over a large area and growing of adult rabbit myogenic stem cells on them. Obtained results show the polymeric scaffolds to be applicable for cell growth practice. It exhibit potential to use it for artificial pericardium in the experimental model in the future.

Schlenk Techniques for Anionic Polymerization

KAUST Repository

Ratkanthwar, Kedar; Zhao, Junpeng; Zhang, Hefeng; Hadjichristidis, Nikolaos; Mays, Jimmy

2015-01-01

Anionic polymerization-high vacuum techniques (HVTs) are doubtlessly the most prominent and reliable experimental tools to prepare polymer samples with well-defined and, in many cases, complex macromolecular architectures. Due to the high demands

Monte Carlo simulation on kinetics of batch and semi-batch free radical polymerization

KAUST Repository

Shao, Jing

2015-10-27

Based on Monte Carlo simulation technology, we proposed a hybrid routine which combines reaction mechanism together with coarse-grained molecular simulation to study the kinetics of free radical polymerization. By comparing with previous experimental and simulation studies, we showed the capability of our Monte Carlo scheme on representing polymerization kinetics in batch and semi-batch processes. Various kinetics information, such as instant monomer conversion, molecular weight, and polydispersity etc. are readily calculated from Monte Carlo simulation. The kinetic constants such as polymerization rate k p is determined in the simulation without of “steady-state” hypothesis. We explored the mechanism for the variation of polymerization kinetics those observed in previous studies, as well as polymerization-induced phase separation. Our Monte Carlo simulation scheme is versatile on studying polymerization kinetics in batch and semi-batch processes.

Imidazoline and imidazolidine nitroxides as controlling agents in nitroxide-mediated pseudoliving radical polymerization

Science.gov (United States)

Edeleva, M. V.; Marque, S. R. A.; Bagryanskaya, E. G.

2018-04-01

Controlled, or pseudoliving, radical polymerization provides unique opportunities for the synthesis of structurally diverse polymers with a narrow molecular-weight distribution. These reactions occur under relatively mild conditions with broad tolerance to functional groups in the monomers. The nitroxide-mediated pseudoliving radical polymerization is of particular interest for the synthesis of polymers for biomedical applications. This review briefly describes one of the mechanisms of controlled radical polymerization. The studies dealing with the use of imidazoline and imidazolidine nitroxides as controlling agents for nitroxide-mediated pseudoliving radical polymerization of various monomers are summarized and analyzed. The publications addressing the key steps of the controlled radical polymerization in the presence of imidazoline and imidazolidine nitroxides and new approaches to nitroxide-mediated polymerization based on protonation of both nitroxides and monomers are considered. The bibliography includes 154 references.

Microencapsulated Comb-Like Polymeric Solid-Solid Phase Change Materials via In-Situ Polymerization

Directory of Open Access Journals (Sweden)

Wei Li

2018-02-01

Full Text Available To enhance the thermal stability and permeability resistance, a comb-like polymer with crystallizable side chains was fabricated as solid-solid phase change materials (PCMs inside the cores of microcapsules and nanocapsules prepared via in-situ polymerization. In this study, the effects on the surface morphology and microstructure of micro/nanocapsules caused by microencapsulating different types of core materials (i.e., n-hexadecane, ethyl hexadecanoate, hexadecyl acrylate and poly(hexadecyl acrylate were systematically studied via field emission scanning electron microscope (FE-SEM and transmission electron microscope (TEM. The confined crystallization behavior of comb-like polymer PCMs cores was investigated via differential scanning calorimeter (DSC. Comparing with low molecular organic PCMs cores, the thermal stability of PCMs microencapsulated comb-like polymer enhanced significantly, and the permeability resistance improved obviously as well. Based on these resultant analysis, the microencapsulated comb-like polymeric PCMs with excellent thermal stability and permeability resistance showed promising foreground in the field of organic solution spun, melt processing and organic coating.

Intrinsic embedded sensors for polymeric mechatronics: flexure and force sensing.

Science.gov (United States)

Jentoft, Leif P; Dollar, Aaron M; Wagner, Christopher R; Howe, Robert D

2014-02-25

While polymeric fabrication processes, including recent advances in additive manufacturing, have revolutionized manufacturing, little work has been done on effective sensing elements compatible with and embedded within polymeric structures. In this paper, we describe the development and evaluation of two important sensing modalities for embedding in polymeric mechatronic and robotic mechanisms: multi-axis flexure joint angle sensing utilizing IR phototransistors, and a small (12 mm), three-axis force sensing via embedded silicon strain gages with similar performance characteristics as an equally sized metal element based sensor.

Polymerization Simulator for Introductory Polymer and Material Science Courses

Science.gov (United States)

Chirdon, William M.

2010-01-01

This work describes how molecular simulation of polymerization reactions can be used to enrich introductory polymer or material science courses to give students a deeper understanding of free-radical chain and stepwise growth polymerization reactions. These simulations have proven to be effective media for instruction that do not require material…

Forming of Polymeric Tubular Micro-components

DEFF Research Database (Denmark)

Qin, Yi; Zhao, Jie; Anyasodor, Gerald

2015-01-01

platform for the production of functional polymeric tubular micro-components. The chapter gives background on the current market and process development trends, followed by description of materials, process configuration, tool design and machine development for each processing technology as well......This chapter is intended to provide an overview of three nontraditional shaping technologies for the forming of polymeric micro-tubes, which are hot embossing, blow molding, and cross rolling, as well as realization of a process chain and the integration of a modular machine-based manufacturing...... as strategy for integration of the technologies and equipment into a common platform. Finally, potential applications of the technologies and facilities developed are highlighted....

Inclusion: Conceptualization and measurement

NARCIS (Netherlands)

Jansen, W.S.; Otten, S.; Van der Zee, K.I.; Jans, L.

2014-01-01

n the present research, we introduced a conceptual framework of inclusion and subsequently used this as a starting point to develop and validate a scale to measure perceptions of inclusion. Departing from existing work on inclusion and complementing this with theoretical insights from optimal

Inclusion : Conceptualization and measurement

NARCIS (Netherlands)

Jansen, Wiebren S.; Otten, Sabine; van der Zee, Karen I.; Jans, Lise

In the present research, we introduced a conceptual framework of inclusion and subsequently used this as a starting point to develop and validate a scale to measure perceptions of inclusion. Departing from existing work on inclusion and complementing this with theoretical insights from optimal

Inclusion: Conceptualization and measurement

NARCIS (Netherlands)

Jansens, Wiebren S.; Otten, Sabine; van der Zee, Karen; Jans, Lise

2014-01-01

In the present research, we introduced a conceptual framework of inclusion and subsequently used this as a starting point to develop and validate a scale to measure perceptions of inclusion. Departing from existing work on inclusion and complementing this with theoretical insights from optimal

EB curing of oxidative-polymerized linseed oil

International Nuclear Information System (INIS)

Ju Xuecheng; Ha Hongfei

2000-01-01

The properties of EB curing coating films, which were determined by the structure of oxidative-polymerized linseed oil, were as following: good gloss, low hardness, better flexibility and impact resistance, low glass transition temperature and bad adhesion on tinplate. Oxidative-polymerized linseed oil could be used with other compositions not only as oligomer, but also as functional monomer to improve the properties of coating films of composite systems. Both absorbed dose sand Cobaltous naphthenate had little influence on the properties of these coating films

Cloud Ablation by a Relativistic Jet and the Extended Flare in CTA 102 in 2016 and 2017

Science.gov (United States)

Zacharias, M.; Böttcher, M.; Jankowsky, F.; Lenain, J.-P.; Wagner, S. J.; Wierzcholska, A.

2017-12-01

In late 2016 and early 2017, the flat spectrum radio quasar CTA 102 exhibited a very strong and long-lasting outburst. The event can be described by a roughly two-month long increase of the baseline flux in the monitored energy bands (optical to γ-rays) by a factor 8, and a subsequent decrease over another two months back to pre-flare levels. The long-term trend was superseded by short but very strong flares, resulting in a peak flux that was a factor 50 above pre-flare levels in the γ-ray domain and almost a factor 100 above pre-flare levels in the optical domain. In this paper, we explain the long-term evolution of the outburst by the ablation of a gas cloud penetrating the relativistic jet. The slice-by-slice ablation results in a gradual increase of the particle injection until the center of the cloud is reached, after which the injected number of particles decreases again. With reasonable cloud parameters, we obtain excellent fits of the long-term trend.

Imaging and Variability Studies of CTA 102 during the 2016 January γ-ray Flare

Science.gov (United States)

Li, Xiaofeng; Mohan, P.; An, T.; Hong, Xiaoyu; Cheng, Xiaopeng; Yang, Jun; Zhang, Yingkang; Zhang, Zhongli; Zhao, Wei

2018-02-01

The γ-ray-bright blazar CTA 102 is studied using imaging (new 15 GHz and archival 43 GHz Very Long Baseline Array, VLBA data) and time variable optical flux density, polarization degree, and electric vector position angle (EVPA) spanning between 2015 June 1 and 2016 October 1, covering a prominent γ-ray flare during 2016 January. The pc-scale jet indicates expansion with oscillatory features up to 17 mas. Component proper motions are in the range 0.04–0.33 mas yr‑1 with acceleration up to 1.2 mas followed by a slowing down beyond 1.5 mas. A jet bulk Lorentz factor ≥17.5, position angle of 128.°3, inclination angle ≤6.°6 and intrinsic half opening angle ≤1.°8 are derived from the VLBA data. These inferences are employed in a helical jet model to infer long-term variability in flux density, polarization degree, EVPA, and a rotation of the Stokes Q and U parameters. A core distance of r core,43 GHz = 22.9 pc, and a magnetic field strength at 1 pc and the core location of 1.57 G and 0.07 G, respectively, are inferred using the core-shift method. The study is useful in the context of estimating jet parameters and in offering clues to distinguish mechanisms responsible for variability over different timescales.

Associating Polymer Networks Based on Cyclodextrin Inclusion Compounds for Heavy Oil Recovery

Directory of Open Access Journals (Sweden)

Xi Li

2018-01-01

Full Text Available This work evaluates an approach to improve the enhanced heavy oil recovery performance of hydrophobic associating polymer. A polymeric system based on water-soluble hydrophobic associating polymer (WSHAP and cyclodextrin (CD polymer was proposed in this work. Addition of CD polymer to WSHAP forms interpolymer bridges by inclusion of CD groups with hydrophobic tails, and thereby the network structure is strengthened. The proposed system offers good viscoelasticity, pronounced shear thinning, and interesting viscosity-temperature relations. Sand pack tests indicated that the proposed system can build high resistance factor during the propagation in porous media, and its moderate adsorption phenomenon was represented by the thickness of the adsorbed layer. The relationship between effective viscosity and oil recovery increment indicated that the proposed system can significantly reduce the residual oil saturation due to the “piston-like” propagation. The overall oil recovery was raised by 5.7 and 24.5% of the original oil in place compared with WSHAP and partially hydrolyzed polyacrylamide (HPAM, respectively.

Comparison of Spot Sign, Blend Sign and Black Hole Sign for Outcome Prediction in Patients with Intracerebral Hemorrhage.

Science.gov (United States)

Sporns, Peter B; Schwake, Michael; Kemmling, André; Minnerup, Jens; Schwindt, Wolfram; Niederstadt, Thomas; Schmidt, Rene; Hanning, Uta

2017-09-01

Blend sign (BS) and black hole sign (BHS) on non-contrast computed tomography (NCCT) and spot sign (SS) on CT-angiography (CTA) are indicators of early hematoma expansion in spontaneous intracerebral hemorrhage (ICH). However, their independent contributions to outcome have not been well explored. In this retrospective study, inclusion criteria were: 1) spontaneous ICH and 2) NCCT and CTA performed on admission within 6 hours after onset of symptoms. Discharge outcome was dichotomized as good (modified Rankin Scale [mRS] 0-3) and poor (mRS 4-6) outcomes. The impacts of BHS, BS and SS on outcome were assessed in univariate and multivariable logistic regression models. Of 182 patients with spontaneous ICH, 26 (14.3%) presented with BHS, 37 (20.3%) with BS and 39 (21.4%) with SS. There was a substantial correlation between SS and BS (κ=0.701) and a moderate correlation between SS and BHS (κ=0.424). In univariable logistic regression, higher baseline hematoma volume ( P <0.001), intraventricular hemorrhage ( P =0.002) and the presence of BHS/BS/SS (all P <0.001) on admission CT scan were associated with poor outcome. Multivariable analysis identified intraventricular haemorrhage (odds ratio [OR] 2.22 per mL, P =0.022), baseline hematoma volume (OR 1.03 per mL, P <0.001) and SS on CTA (OR 11.43, P <0.001) as independent predictors of poor outcome, showing that SS compared to BS and BHS was more powerful to predict poor outcome. The NCCT BHS and BS are correlated with the CTA SS and are reliable predictors of poor outcome in patients with ICH. Of the CT variables indicating early hematoma expansion, SS on CTA was the most reliable outcome predictor. However, given their correlation with SS on CTA, BS and BHS on NCCT can be useful for predicting outcome if CTA is not obtainable.

Evidence on Inclusion

DEFF Research Database (Denmark)

Dyssegaard, Camilla Brørup; Larsen, Michael Søgaard

The purpose of this publication is to examine existing research on inclusion to identify strategies of inclusion that have generated positive effects. To do so it is necessary to understand the effect of the applied strategies. One approach, which is being discussed, is to use evidence to determine...... which methods have proven more effective than others. The desire to gain insight into research on inclusion forms the basis of the current systematic review. The task was to determine which strategies primary research has found to be most effective for inclusion purposes. We have solved this task...... by addressing the existing research with the following question: What is the effect of including children with special needs in mainstream teaching in basic school, and which of the applied educational methods have proved to have a positive effect?...

Development of polymeric nanoparticles showing tuneable pH-responsive precipitation

Energy Technology Data Exchange (ETDEWEB)

Vakurov, Alexander, E-mail: a.v.vakourov@bmb.leeds.ac.uk; Pchelintsev, Nikolay A., E-mail: n.a.pchelintsev@googlemail.com; Gibson, Tim, E-mail: timdgibson@merchab.fsnet.co.uk; Millner, Paul, E-mail: p.a.millner@leeds.ac.uk [Research Institute of Membrane and Systems Biology, University of Leeds (United Kingdom)

2012-12-15

A reverse micellar system comprising dioctyl-sulfosuccinate (AOT)/toluene was used as a template for polymerization of acrylamide/bisacrylamide-based functionalized polymeric nanoparticles. Such nanoparticles were typically sized between 20 and 90 nm and could be synthesized with a wide range of functional groups according to the monomers added to the polymerization mixture. Carboxy nanoparticles with acrylic acid as the functional monomer were synthesized in the reported work. The carboxy nanoparticles were pH sensitive and precipitated at pHs below 4. Modification of carboxy-functionalized polymeric nanoparticles with polyetheleneimine (PEI) resulted in the fabrication of a series of pH-responsive nanoparticles which could precipitate at different pHs and ionic strengths according to the PEI/carboxy ratio in the system. Both non-covalent PEI-nanoparticles conjugates and nanoparticles with covalently linked PEI behaved in this way.

Development of polymeric nanoparticles showing tuneable pH-responsive precipitation

International Nuclear Information System (INIS)

Vakurov, Alexander; Pchelintsev, Nikolay A.; Gibson, Tim; Millner, Paul

2012-01-01

A reverse micellar system comprising dioctyl-sulfosuccinate (AOT)/toluene was used as a template for polymerization of acrylamide/bisacrylamide-based functionalized polymeric nanoparticles. Such nanoparticles were typically sized between 20 and 90 nm and could be synthesized with a wide range of functional groups according to the monomers added to the polymerization mixture. Carboxy nanoparticles with acrylic acid as the functional monomer were synthesized in the reported work. The carboxy nanoparticles were pH sensitive and precipitated at pHs below 4. Modification of carboxy-functionalized polymeric nanoparticles with polyetheleneimine (PEI) resulted in the fabrication of a series of pH-responsive nanoparticles which could precipitate at different pHs and ionic strengths according to the PEI/carboxy ratio in the system. Both non-covalent PEI-nanoparticles conjugates and nanoparticles with covalently linked PEI behaved in this way.

Radiological response of ceramic and polymeric devices for breast brachytherapy

International Nuclear Information System (INIS)

Batista Nogueira, Luciana; Passos Ribeiro de Campos, Tarcisio

2012-01-01

In the present study, the radiological visibility of ceramic and polymeric devices implanted in breast phantom was investigated for future applications in brachytherapy. The main goal was to determine the radiological viability of ceramic and polymeric devices in vitro by performing simple radiological diagnostic methods such as conventional X-ray analysis and mammography due to its easy access to the population. The radiological response of ceramic and polymeric devices implanted in breast phantom was determined using conventional X-ray, mammography and CT analysis. - Highlights: ► Radiological visibility of ceramic and polymeric devices implanted in breast phantom. ► The barium incorporation in the seed improves the radiological contrast. ► Radiological monitoring shows the position, orientation and degradation of devices. ► Simple radiological methods such as X-ray and mammography were used for radiological monitoring.

Site-selective metallization of polymeric substrates by the hyperbranched polymer templates

International Nuclear Information System (INIS)

Li, Peiyuan; Yang, Fang; Li, Xiangcheng; He, Chunling; Su, Wei; Chen, Jinhao; Huo, Lini; Chen, Rui; Lu, Chensheng; Liang, Lifang

2013-01-01

We demonstrate a simple, cost-effective and universal technique for the fabrication of copper circuit pattern on flexible polymeric substrate. This method relies on a ternary polyethylenimine-poly(acrylic acid)-substrate film incorporating palladium catalysts, which are used as adhesive interlayers for the copper metallization of flexible polymeric substrates. We demonstrated the fabrication of patterned copper films on a variety of flexible polymers with minimum feature sizes of 200 μm. And the resulting copper circuit showed strong adhesion with underlying flexible polymeric substrates. The films were characterized by ATR FT-IR, contact angle, XPS, XRD, TEM and SEM. The direct patterning of metallic circuit on flexible polymeric substrate indicates great potential for the use in electronics industry.

Site-selective metallization of polymeric substrates by the hyperbranched polymer templates

Energy Technology Data Exchange (ETDEWEB)

Li, Peiyuan, E-mail: lipearpear@163.com [College of Pharmacy, Guangxi University of Chinese Medicine, Nanning 530001 (China); Yang, Fang [College of Chemistry and Life Science, Guangxi Teachers Education University, Nanning 530001 (China); Li, Xiangcheng [School of Computer, Electronics and Information, Guangxi University, Nanning 530001 (China); He, Chunling [College of Pharmacy, Guangxi University of Chinese Medicine, Nanning 530001 (China); Su, Wei, E-mail: suwmail@163.com [College of Chemistry and Life Science, Guangxi Teachers Education University, Nanning 530001 (China); Chen, Jinhao [College of Chemistry and Life Science, Guangxi Teachers Education University, Nanning 530001 (China); Huo, Lini; Chen, Rui; Lu, Chensheng [College of Pharmacy, Guangxi University of Chinese Medicine, Nanning 530001 (China); Liang, Lifang [College of Chemistry and Life Science, Guangxi Teachers Education University, Nanning 530001 (China)

2013-09-01

We demonstrate a simple, cost-effective and universal technique for the fabrication of copper circuit pattern on flexible polymeric substrate. This method relies on a ternary polyethylenimine-poly(acrylic acid)-substrate film incorporating palladium catalysts, which are used as adhesive interlayers for the copper metallization of flexible polymeric substrates. We demonstrated the fabrication of patterned copper films on a variety of flexible polymers with minimum feature sizes of 200 μm. And the resulting copper circuit showed strong adhesion with underlying flexible polymeric substrates. The films were characterized by ATR FT-IR, contact angle, XPS, XRD, TEM and SEM. The direct patterning of metallic circuit on flexible polymeric substrate indicates great potential for the use in electronics industry.

Metal-ion catalyzed polymerization in the eutectic phase in water-ice

DEFF Research Database (Denmark)

Monnard, Pierre-Alain; Szostak, Jack W.

2008-01-01

The emergence of an RNA world requires among other processes the non-enzymatic, template-directed replication of genetic polymers such as RNA or related nucleic acids, possibly catalyzed by metal ions. The absence of uridilate derivative polymerization on adenine containing templates has been...... the main issue preventing an efficient template-directed RNA polymerization. We report here the investigation of template-directed RNA polymerization in the eutectic phase in water-ice. In particular, it was found that activated Uridilate monomers in the presence of metal-ion catalysts could efficiently......-pairing opportunities. These results suggest that a template-directed RNA polymerization catalyzed by metal-ions could be carried out under eutectic phase in water-ice conditions....

Growth of polymer nanoparticles in microemulsion polymerization initiated with γ ray

International Nuclear Information System (INIS)

Xu Xiangling; Ge Xuewu; Ye Qiang; Zhang Zhicheng; Zuo Ju; Niu Aizhen; Zhang Manwei

1999-01-01

In microemulsion polymerization of styrene, butyl acrylate and methyl methacrylate initiated with gamma ray, growth of polymer nanoparticles was observed with photon correlation spectroscopy, and the conversion curve was recorded with a dilatometer. There is some similarity in the growth of polymer particles. The size of polymer particles rapidly increases up to their maximum at the early stage. With the increase of conversion, the large particles supply their monomer to newly formed particles and become smaller. In all these three microemulsion polymerizations, the evidence of continuous nucleation was observed. When monomer is styrene or butyl acrylate, a plateau of polymerization rate emerges. When monomer is methyl methacrylate, no plateau of polymerization is observed

De fysica van polymere materialen

NARCIS (Netherlands)

Struik, L.C.E.

1987-01-01

Rede, uitgesproken ter gelegenheid van de aanvaarding van het ambt van buitengewoon hoogleraar in de fysica van polymere materialen aan de Universitelt Twente op donderdag 22 januarì 1987 door Dr.lr. L.C.E. Struik.

X-ray initiated polymerization of wood impregnants

Energy Technology Data Exchange (ETDEWEB)

Cleland, Marshall R.; Galloway, Richard A. [IBA Industrial, Inc., Edgewood, NY (United States); Berejka, Anthony J. [Ionicorp, Huntington, NY 11743 (United States)], E-mail: berejka@msn.com; Montoney, Daniel [Strathmore Products, Syracuse, NY (United States); Driscoll, Mark; Smith, Leonard; Scott Larsen, L. [State University of New York, SUNY-ESF, Syracuse, NY (United States)

2009-07-15

X-rays, derived from a high energy, high-current electron beam (EB), initiated in-situ polymerization of a unique class of monomers that were found to penetrate the cell walls of wood. X-rays initiated an auto-catalytic acrylic polymerization and penetrated through thick pieces of wood. The final cured product having the polymerizate, a polymer, both in the wood cell lumens and in the cell walls is called wood impregnated with a wood-polymer penetrant (WPP). The controlled lower dose rate of X-rays overcame disproportionation encountered when using higher dose-rate electron beam initiation. With X-rays, the in-situ polymerization took place in one exposure of modest dose. With EB, multiple passes were needed to avoid excessive heat build-up and monomer volatilization. Having entered the cell walls of the wood and then being polymerized within the cell walls, these radiation-cured unique monomers imparted outstanding dimensional stability upon exposure of the impregnated wood to humidity cycling. The preferred monomer system was also chemically modified prior to impregnation with agents that would remain in the wood and prevent the growth of fungi and other microbials. This technique differs from historic uses of monomers that merely filled the lumens of the wood (historic wood-polymer composites), which are only suitable for indoor use. The WPP impregnated wood that was either X-ray cured or EB cured demonstrated enhanced structural properties, dimensional stability, and decay resistance.

X-ray initiated polymerization of wood impregnants

International Nuclear Information System (INIS)

Cleland, Marshall R.; Galloway, Richard A.; Berejka, Anthony J.; Montoney, Daniel; Driscoll, Mark; Smith, Leonard; Scott Larsen, L.

2009-01-01

X-rays, derived from a high energy, high-current electron beam (EB), initiated in-situ polymerization of a unique class of monomers that were found to penetrate the cell walls of wood. X-rays initiated an auto-catalytic acrylic polymerization and penetrated through thick pieces of wood. The final cured product having the polymerizate, a polymer, both in the wood cell lumens and in the cell walls is called wood impregnated with a wood-polymer penetrant (WPP). The controlled lower dose rate of X-rays overcame disproportionation encountered when using higher dose-rate electron beam initiation. With X-rays, the in-situ polymerization took place in one exposure of modest dose. With EB, multiple passes were needed to avoid excessive heat build-up and monomer volatilization. Having entered the cell walls of the wood and then being polymerized within the cell walls, these radiation-cured unique monomers imparted outstanding dimensional stability upon exposure of the impregnated wood to humidity cycling. The preferred monomer system was also chemically modified prior to impregnation with agents that would remain in the wood and prevent the growth of fungi and other microbials. This technique differs from historic uses of monomers that merely filled the lumens of the wood (historic wood-polymer composites), which are only suitable for indoor use. The WPP impregnated wood that was either X-ray cured or EB cured demonstrated enhanced structural properties, dimensional stability, and decay resistance.

Intrinsic Embedded Sensors for Polymeric Mechatronics: Flexure and Force Sensing

Directory of Open Access Journals (Sweden)

Leif P. Jentoft

2014-02-01

Full Text Available While polymeric fabrication processes, including recent advances in additive manufacturing, have revolutionized manufacturing, little work has been done on effective sensing elements compatible with and embedded within polymeric structures. In this paper, we describe the development and evaluation of two important sensing modalities for embedding in polymeric mechatronic and robotic mechanisms: multi-axis flexure joint angle sensing utilizing IR phototransistors, and a small (12 mm, three-axis force sensing via embedded silicon strain gages with similar performance characteristics as an equally sized metal element based sensor.

Atom transfer radical polymerization of styrene under pulsed microwave irradiation

International Nuclear Information System (INIS)

Cheng Zhenping; Zhu Xiulin; Zhou Nianchen; Zhu Jian; Zhang Zhengbiao

2005-01-01

A homogeneous solution atom transfer radical polymerization (ATRP) and reverse atom transfer radical polymerization (RATRP) of styrene (St) in N,N-dimethylformamide (DMF) were successfully carried out under pulsed microwave irradiation (PMI), using 1-bromo-1-phenylethane (1-PEBr)/CuCl/N,N,N',N'',N''-pentamethyldiethylenetriamine (PMDETA) as an initiating system at 85 deg. C and 2,2'-azo-bis-isobutyrontrile (AIBN)/CuCl 2 /PMDETA as an initiating system at 95 deg. C, respectively. The polymerization rates under PMI were greatly increased in comparison with those under identical conventional heating (CH)

PREPARATION AND PROPERTY OF POLYMERIC PENDANT Ru(bpy)32+ COMPLEXES

Institute of Scientific and Technical Information of China (English)

HOU Xiaohuai; Masao Kaneko; Akira Yamada

1984-01-01

Polymeric pendant Ru(bpy)32+ complexes were prepared from homopolymer and copolymers of 4-methyl-4'-vinyl-2,2'-bipyridine (Vbpy). Vbpy was prepared from 4-methylpyridine. The comonomers were styrene (St), acrylic acid (AA), N-vinylpyrrolidone (Pyr), 4-vinylpyridine (Vpy), methyl methacrylate (MMA), 2-hydroxyethyl methacrylate (HEMA), acrylonitrile (AN) and N-ethyl-4-vinylpyridium bromide (EQ-Vpy). The fraction of the pendant Ru(bpy)32+ repeating unit in the polymeric complex was 0.022 to 0.052. Absorption maximum, molar extinction coefficient, emission maximum and relative emission intensity of the polymeric complexes were studied.

GAMMA RADIATION INITIATED POLYMERIZATION OF FLUOROMONOMERS. II. COPOLYMER OF CHLOROTRIFLUOROETHYLENE AND ETHYLENE

Energy Technology Data Exchange (ETDEWEB)

Manno, P. J.

1963-06-15

The radioinduced copolymerization of chlorotrifluoro ethylene and ethylene was studied. The polymerization rate increased with time and radiation intensity, and the Gvalues after 50% polymerization varied from 13,000 at 10/sup 5/ rep/hr to 25,000 at 6 x 10/sup 3/ rep/hr. The polymerization rate is proportional to the 0.7 or 0.8th power of the radiation intensity. The polymerization reaction is highly exothermic, and the optimum conditions for the best polymer properties occurred in a stirred autoclave cooled to 0 deg C containing a monomer-- water mixture and irradiated at 10/sup 4/ rep/hr. Catalytic polymerization was also studied, and the economics of or the preparation of the copolymer by catalytic and radiation processes is discussed briefly. (D.L.C.)

Production methodologies of polymeric and hydrogel particles for drug delivery applications.

Science.gov (United States)

Lima, Ana Catarina; Sher, Praveen; Mano, João F

2012-02-01

Polymeric particles are ideal vehicles for controlled delivery applications due to their ability to encapsulate a variety of substances, namely low- and high-molecular mass therapeutics, antigens or DNA. Micro and nano scale spherical materials have been developed as carriers for therapies, using appropriated methodologies, in order to achieve a prolonged and controlled drug administration. This paper reviews the methodologies used for the production of polymeric micro/nanoparticles. Emulsions, phase separation, spray drying, ionic gelation, polyelectrolyte complexation and supercritical fluids precipitation are all widely used processes for polymeric micro/nanoencapsulation. This paper also discusses the recent developments and patents reported in this field. Other less conventional methodologies are also described, such as the use of superhydrophobic substrates to produce hydrogel and polymeric particulate biomaterials. Polymeric drug delivery systems have gained increased importance due to the need for improving the efficiency and versatility of existing therapies. This allows the development of innovative concepts that could create more efficient systems, which in turn may address many healthcare needs worldwide. The existing methods to produce polymeric release systems have some critical drawbacks, which compromise the efficiency of these techniques. Improvements and development of new methodologies could be achieved by using multidisciplinary approaches and tools taken from other subjects, including nanotechnologies, biomimetics, tissue engineering, polymer science or microfluidics.

Polymerization of Alkylsilanes on ZIF-8 to Hierarchical Siloxane Microspheres and Microflowers

Directory of Open Access Journals (Sweden)

Lin Yang

2017-03-01

Full Text Available The use of metal-organic frameworks (MOFs in the polymerization field remains comparatively rare up to now, let alone studies on the fabrication of polymer microstructures through a MOFs-catalyzed assembly process. Zeolitic imidazolate framework-8 (ZIF-8, a well-known MOF for its chemical and thermal stabilities, was used to induce a polymerization reaction of saturated alkylsilanes for the first time. The reaction temperature was found to be critical for morphology control of the polymerized ZIF-siloxane composites. The polymerization of alkylsilanes by ZIF-8 at room temperature resulted in siloxane microspheres while rose petal-like microstructures were obtained at higher temperature. The effects of the reaction time on the structures of the polymerization products were also investigated and the polymerization reaction process was proposed. This work expands the field of MOFs’ applications and develops a reasonable method for the multidimensional assembly of MOFs building blocks into required structures or platforms for designing new kinds of hierarchical morphologies, which to our knowledge has not been previously investigated.

Radiation-induced heterogeneous polymerization of acrylamide in acetone and acetone--water mixtures

International Nuclear Information System (INIS)

Wada, T.; Sekiya, H.; Machi, S.

1975-01-01

The effects of temperature, dose rate, and monomer concentration on the heterogeneous polymerization of acrylamide in acetone--water mixtures have been studied. Heterogeneous polymerization takes place in mixtures containing less than 60 vol-percent water. The polymerization is steady in acetone and nonsteady in mixtures containing 10 to 50 vol-percent water. The average rate of polymerization is highest in mixtures with about 20 vol-percent water. Polymer molecular weight increases with the increasing water content in the range 0 to 10 vol-percent and does not change in the range of 30 to 70 vol-percent water. For the polymerization in acetone and an acetone-water 60/40 mixture, the activation energies are 2.3 and -1.8 kcal/mole, the dose rate exponents of rate are 0.78 and 0.52, and the monomer concentration exponents of rate are 0.5 and 1.6, respectively. The polymer molecular weight increases with decreasing dose rate, decreasing temperature, and increasing monomer concentration. These results are discussed in connection with the mechanism of heterogeneous polymerization and the solvent effect

Footstep towards Inclusive Education

Science.gov (United States)

Abbas, Faiza; Zafar, Aneeka; Naz, Tayyaba

2016-01-01

Inclusive education is a rising trend in the world. The first step towards inclusive education is providing the awareness to the general education teachers. This study focused to investigate the general education teachers of primary and secondary level awareness about the special education and inclusive education. This study is descriptive method…

Polyethylene-waste tire dust composites via in situ polymerization

International Nuclear Information System (INIS)

Reyes A, Y. K.; Narro C, R. I.; Ramos A, M. E.; Neira V, M. G.; Diaz E, J.; Enriquez M, F.; Valencia L, L. A.; Saade C, H.; Diaz de L, R.

2014-01-01

Polyethylene/waste tire dust (WTD) composites were obtained by an in situ polymerization technique. The surface of the WTD was modified with deposition of polyethylene by using plasma polymerization. Ethylene polymerization was carried out using bis(cyclopentadienyl) titanium dichloride (Cp 2 TiCl 2 ) as homogeneous metallocenes catalyst, while diethylaluminum chloride (DEAC), ethyl aluminum sesquichloride (EASC) and methyl alumino xane (Mao) were used as co-catalysts at two different [Al]/[Ti] molar ratio. The main characteristics of the obtained polyethylenes were determined by size exclusion chromatography, thermogravimetric analysis, differential scanning calorimetry and wide-angle X-ray diffraction. The results showed that by using EASC and Mao the highest catalytic activities were presented at a [Al]/[Ti] molar ratio of 9.17 and 18.33 respectively. Even though it was possible to obtain polyethylene using WTD (modified or unmodified) the catalytic activity was lower than in the case in which no WTD was added in ethylene polymerization. Scanning transmission electronic microscopy images evidenced that the original morphology of the polyethylenes was not modified by the presence of WTD. (Author)

Polyethylene-waste tire dust composites via in situ polymerization

Energy Technology Data Exchange (ETDEWEB)

Reyes A, Y. K.; Narro C, R. I.; Ramos A, M. E. [Universidad Autonoma de Coahuila, Facultad de Ciencias Quimicas, Blvd. Venustiano Carranza s/n, 25280 Saltillo, Coahuila (Mexico); Neira V, M. G.; Diaz E, J.; Enriquez M, F.; Valencia L, L. A.; Saade C, H.; Diaz de L, R., E-mail: ramon.diazdeleon@ciqa.edu.mx [Centro de Investigacion en Quimica Aplicada, Blvd. Enrique Reyna Hermosillo No. 40, Col. San Jose de los Cerritos, 25293 Saltillo, Coahuila (Mexico)

2014-10-01

Polyethylene/waste tire dust (WTD) composites were obtained by an in situ polymerization technique. The surface of the WTD was modified with deposition of polyethylene by using plasma polymerization. Ethylene polymerization was carried out using bis(cyclopentadienyl) titanium dichloride (Cp{sub 2}TiCl{sub 2}) as homogeneous metallocenes catalyst, while diethylaluminum chloride (DEAC), ethyl aluminum sesquichloride (EASC) and methyl alumino xane (Mao) were used as co-catalysts at two different [Al]/[Ti] molar ratio. The main characteristics of the obtained polyethylenes were determined by size exclusion chromatography, thermogravimetric analysis, differential scanning calorimetry and wide-angle X-ray diffraction. The results showed that by using EASC and Mao the highest catalytic activities were presented at a [Al]/[Ti] molar ratio of 9.17 and 18.33 respectively. Even though it was possible to obtain polyethylene using WTD (modified or unmodified) the catalytic activity was lower than in the case in which no WTD was added in ethylene polymerization. Scanning transmission electronic microscopy images evidenced that the original morphology of the polyethylenes was not modified by the presence of WTD. (Author)

More Policies, Greater Inclusion? Exploring the Contradictions of New Labour Inclusive Education Policy

Science.gov (United States)

Roulstone, Alan; Prideaux, Simon

2008-01-01

The era of New Labour government has witnessed unprecedented growth in inclusive education policies. There is, however, limited evidence that policies have increased disabled children's inclusion. This article explores reasons for this contradiction. Drawing on sociological insights, it is argued that New Labour policies on inclusive education…

Prevalence of pesticides in postconsumer agrochemical polymeric packaging.

Science.gov (United States)

Eras, J; Costa, J; Vilaró, F; Pelacho, A M; Canela-Garayoa, R; Martin-Closas, L

2017-02-15

Pesticide remains contained in agrochemical packaging waste are a source of uncontrolled risk for human health; they are also a quality feedstock for the plastic recycling industry. Many governments have recently started to establish laws and regulations to develop systems for recovering and recycling the polymeric packages used for pesticides. There is also a demand in having a procedure to control the suitability of the pesticide packages to be reused. We have developed a two-step operation process to assess the pesticide residues in agricultural containers made of a variety of polymeric matrices. The procedure is based on an extraction with a solvent mixture followed by UPLC-MS/MS determination. Solvents for neutral pesticides were selected considering the Hildebrand solubility (δ) of solvents and polymers together with those estimated for the pesticides. The proposed technique is effective in recovering imbibed pesticides in polymeric matrices. Also, a simplified extraction procedure has been tested to become a routine method for these wastes. We have found that in many cases a significant amount of pesticides remain into the polymeric matrix, even after a standardized cleaning; the impact of releasing these hazardous compounds into the environment is to be of further consideration. Copyright © 2016 Elsevier B.V. All rights reserved.

Nuclear magnetic resonance applied to the study of polymeric nano composites

International Nuclear Information System (INIS)

Tavares, Maria Ines Bruno

2011-01-01

Polymers and nanoparticles based nano composites were prepared by intercalation by solution. The obtained nano composites were characterized mainly by the nuclear magnetic spectroscopy (NMR), applying the analysis of carbon-13 (polymeric matrix), silicon-29 (nanoparticle), and by determination of spin-lattice relaxation of the hydrogen nucleus (T 1 H) (polymeric matrix). The NMR have presented a promising technique in the characterization of the nano charge dispersion in the studied polymeric matrixes.

Enantioselective Epoxide Polymerization Using a Bimetallic Cobalt Catalyst

KAUST Repository

Thomas, Renee M.

2010-11-24

A highly active enantiopure bimetallic cobalt complex was explored for the enantioselective polymerization of a variety of monosubstituted epoxides. The polymerizations were optimized for high rates and stereoselectivity, with s-factors (kfast/kslow) for most epoxides exceeding 50 and some exceeding 300, well above the threshold for preparative utility of enantiopure epoxides and isotactic polyethers. Values for mm triads of the resulting polymers are typically greater than 95%, with some even surpassing 98%. In addition, the use of a racemic catalyst allowed the preparation of isotactic polyethers in quantitative yields. The thermal properties of these isotactic polyethers are presented, with many polymers exhibiting high T m values. This is the first report of the rapid synthesis of a broad range of highly isotactic polyethers via the enantioselective polymerization of racemic epoxides. © 2010 American Chemical Society.

Platinum porphyrins as ionophores in polymeric membrane electrodes

DEFF Research Database (Denmark)

Lvova, Larisa; Verrelli, Giorgio; Nardis, Sara

2011-01-01

A comparative study of Pt(II)- and Pt(IV)-porphyrins as novel ionophores for anion-selective polymeric membrane electrodes is performed. Polymeric membranes of different compositions, prepared by varying plasticizers, cationic and anionic additives and Pt porphyrins, have been examined...... within the electrode membranes, while those based on Pt(IV)TPPCl2 operate via a mixed mode carrier mechanism, evidencing also a partial reduction of the starting ionophore to Pt(II)TPP. Spectrophotometric measurements of thin polymeric films indicate that no spontaneous formation of hydroxide ion bridged...... porphyrin dimers occurs in the membrane plasticized both with high or low dielectric constant plasticizer, due to a low oxophilicity of central Pt. The computational study of various anion–Pt(IV)TPPCl2 complex formation by means of semi-empirical and density functional theory (DFT) methods revealed a good...

Living atom transfer radical polymerization of 4-acetoxystyrene

DEFF Research Database (Denmark)

Gao, Bo; Chen, Xianyi; Ivan, Bela

1997-01-01

Living atom transfer radical polymerization (ATRP) of 4-acetoxystyrene (1), a protected 4-vinylphenol, leading to poly(4-acetoxystyrene) with well-defined molecular weight and narrow molecular weight distribution was carried out in bulk with a,a'-dibromoxylene(2)/CuBr/2,2-bipyridine(bpy) as initi......Living atom transfer radical polymerization (ATRP) of 4-acetoxystyrene (1), a protected 4-vinylphenol, leading to poly(4-acetoxystyrene) with well-defined molecular weight and narrow molecular weight distribution was carried out in bulk with a,a'-dibromoxylene(2)/CuBr/2,2-bipyridine......(bpy) as initiating system. A linear (M) over bar(n), versus monomer conversion plot was found in good accordance with the theoretical line, indicating 100% initiating efficiency. The polymerization is first order in respect to monomer up to about 70% monomer conversion. Deviations from linearity at higher conversion...

Enantioselective Epoxide Polymerization Using a Bimetallic Cobalt Catalyst

KAUST Repository

Thomas, Renee M.; Widger, Peter C. B.; Ahmed, Syud M.; Jeske, Ryan C.; Hirahata, Wataru; Lobkovsky, Emil B.; Coates, Geoffrey W.

2010-01-01

A highly active enantiopure bimetallic cobalt complex was explored for the enantioselective polymerization of a variety of monosubstituted epoxides. The polymerizations were optimized for high rates and stereoselectivity, with s-factors (kfast/kslow) for most epoxides exceeding 50 and some exceeding 300, well above the threshold for preparative utility of enantiopure epoxides and isotactic polyethers. Values for mm triads of the resulting polymers are typically greater than 95%, with some even surpassing 98%. In addition, the use of a racemic catalyst allowed the preparation of isotactic polyethers in quantitative yields. The thermal properties of these isotactic polyethers are presented, with many polymers exhibiting high T m values. This is the first report of the rapid synthesis of a broad range of highly isotactic polyethers via the enantioselective polymerization of racemic epoxides. © 2010 American Chemical Society.

Effects of polymeric carbohydrates on growth and development

DEFF Research Database (Denmark)

Knudsen, Knud Erik Bach

, metabolized and net energy); available energy relative to protein is crucial for performance and carcass quality; second, the proportion of starch to NSP will influence rate and type of metabolites (glucose vs. SCFA) deriving from carbohydrate assimilation, and finally, type of starch (types A, B, and C......The main objective of the presentation is to provide insight into the role of polymeric carbohydrates in growth and development of pigs. Polymeric carbohydrates—starch and non-starch polysaccharides (NSP)—quantitatively represent the largest portion of the diets for pigs and are therefore...... at a slower and more constant rate and with SCFA being absorbed by passive diffusion. Type and levels of polymeric carbohydrates influence growth and development through different mechanisms; first, the proportion of starch to NSP plays an important role for the content of available energy (digestible...

Linguistic Diversity and Social Inclusion

Science.gov (United States)

Piller, Ingrid; Takahashi, Kimie

2011-01-01

This introduction provides the framework for the special issue by describing the social inclusion agenda of neoliberal market democracies. While the social inclusion agenda has been widely adopted, social inclusion policies are often blind to the ways in which language proficiency and language ideologies mediate social inclusion in linguistically…

Inclusive pedagogy

DEFF Research Database (Denmark)

Korsgaard, Morten Timmermann; Mortensen, Stig Skov

of education. The article explores the relationship between Continental and Anglo-American educational theory, and why they seem to have developed in such distinct directions. Beginning with the Anglo-American perspective it is outlined how pedagogy and the so called educational interest became replaced...... and the politicisation of inclusive education, and a positive aim in the form of an argument for a move towards constructing a pedagogical ideal of inclusion....

Characterization of arterial stenosis using 3D imaging: comparison between three imaging techniques (MRA, spiral CTA and 3D DSA) and four display methods (MIP, SR, MPVR, VA) in a phantom study

International Nuclear Information System (INIS)

Bendib, K.; Poirier, C.; Croisille, P.; Roux, J.P.; Devel, D.; Amiel, M.

1999-01-01

Introduction: accurate assessment of arterial stenosis is a major public health issue for the diagnosis and treatment of cardiovascular diseases. The number of imaging techniques and types of software for display of imaging data is increasing. Few studies that compare these different techniques are available in the literature. Materials and methods: using phantoms to reproduce the main types of arterial stenosis, the authors compared three 3D acquisition techniques (MRA, CTA, and 3D DSA) and four types of display methods (MIP, SR, MPVR, and VA). The degree, the shape, and the location of different types of stenoses were analyzed by three experienced observers during two successive readings. Intra- and inter-observer reproducibility were assessed. The results of the various acquisition techniques and display methods also were compared to the digital reference data (CFAO) of the physical phantoms. Results: the degree of intra- and inter-observer reproducibility for the assessment of shape and location of the stenoses was good. Visual assessment of the degree of stenosis showed significant differences between two observers as well as in two readings by one observer. The 3D DSA was the most accurate technique for assessing the degree of stenosis. CTA provided better results than MRA. MPVR provided an accurate assessment of the degree of the stenosis. 3D DSA and CTA assessed stenosis form and localization adequately, with no significant difference; both methods appeared to be more accurate than MRA. SR provided the best information on the eccentric nature of the stenosis. The shape was very well assessed by VA and MPVR. Conclusions: even though 3D DSA is the most accurate acquisition technique for visualization, the combined use of SR and MPVR appears to be the best compromise to describe the morphology and degree of stenosis. Further improvements in automatic 3D image processing could offer a better understanding and increased possibilities for assessing arterial

"No zone" approach in penetrating neck trauma reduces unnecessary computed tomography angiography and negative explorations.

Science.gov (United States)

Ibraheem, Kareem; Khan, Muhammad; Rhee, Peter; Azim, Asad; O'Keeffe, Terence; Tang, Andrew; Kulvatunyou, Narong; Joseph, Bellal

2018-01-01

The most recent management guidelines advocate computed tomography angiography (CTA) for any suspected vascular or aero-digestive injuries in all zones and give zone II injuries special consideration. We hypothesized that physical examination can safely guide CTA use in a "no zone" approach. An 8-year retrospective analysis of all adult trauma patients with penetrating neck trauma (PNT) was performed. We included all patients in whom the platysma was violated. Patients were classified into three groups as follows: hard signs, soft signs, and asymptomatic. CTA use, positive CTA (contrast extravasation, dissection, or intimal flap) and operative details were reported. Primary outcomes were positive CTA and therapeutic neck exploration (TNE) (defined by repair of major vascular or aero-digestive injuries). A total of 337 patients with PNT met the inclusion criteria. Eighty-two patients had hard signs and all of them went to the operating room, of which 59 (72%) had TNE. One hundred fifty-six patients had soft signs, of which CTA was performed in 121 (78%), with positive findings in 12 (10%) patients. The remaining 35 (22%) underwent initial neck exploration, of which 14 (40%) were therapeutic yielding a high rate of negative exploration. Ninty-nine patients were asymptomatic, of which CTA was performed in 79 (80%), with positive findings in 3 (4%), however, none of these patients required TNE. On sub analysis based on symptoms, there was no difference in the rate of TNE between the neck zones in patients with hard signs (P = 0.23) or soft signs (P = 0.51). Regardless of the zone of injury, asymptomatic patients did not require a TNE. Physical examination regardless of the zone of injury should be the primary guide to CTA or TNE in patients with PNT. Following traditional zone-based guidelines can result in unnecessary negative explorations in patients with soft signs and may need rethinking. Copyright © 2017 Elsevier Inc. All rights reserved.

A novel process for ultrasound-induced radical polymerization in CO2-expanded fluids

NARCIS (Netherlands)

Kemmere, M.F.; Kuijpers, M.W.A.; Prickaerts, R.M.H.; Keurentjes, J.T.F.

2005-01-01

A strong viscosity increase upon polymerization hinders cavitation and subsequent radical formation during an ultrasound-induced bulk polymerization. In this work, ultrasound-induced radical polymerizations of methyl methacrylate (MMA) have been performed in CO2-expanded MMA in order to reduce the

Self-folding micropatterned polymeric containers.

Science.gov (United States)

Azam, Anum; Laflin, Kate E; Jamal, Mustapha; Fernandes, Rohan; Gracias, David H

2011-02-01

We demonstrate self-folding of precisely patterned, optically transparent, all-polymeric containers and describe their utility in mammalian cell and microorganism encapsulation and culture. The polyhedral containers, with SU-8 faces and biodegradable polycaprolactone (PCL) hinges, spontaneously assembled on heating. Self-folding was driven by a minimization of surface area of the liquefying PCL hinges within lithographically patterned two-dimensional (2D) templates. The strategy allowed for the fabrication of containers with variable polyhedral shapes, sizes and precisely defined porosities in all three dimensions. We provide proof-of-concept for the use of these polymeric containers as encapsulants for beads, chemicals, mammalian cells and bacteria. We also compare accelerated hinge degradation rates in alkaline solutions of varying pH. These optically transparent containers resemble three-dimensional (3D) micro-Petri dishes and can be utilized to sustain, monitor and deliver living biological components.

SCATTERING FROM RAMIFIED POLYMERIC SYSTEMS

Directory of Open Access Journals (Sweden)

M.Benhamou

2004-01-01

Full Text Available Here, of great interest to us is a quantitative study of the scattering properties from ramified polymeric systems of arbitrary topology. We consider three types of systems, namely ramified polymers in solution, ramified polymer blends, or ternary mixtures made of two ramified polymers of different chemical nature immersed in a good solvent. To achieve the goal of the study, use is made of the Random Phase Approximation. First we determine the exact expression of the form factor of an ideal ramified polymer of any topology, from which we extract the exact expression of its gyration radius. Using the classical Zimm's formulae and the exact form factor, we determine all scattering properties of these three types of ramified polymeric systems. The main conclusion is that ramification of the chains induces drastic changes of the scattering properties.

Inclusion in the East: Chinese Students' Attitudes towards Inclusive Education

Science.gov (United States)

Malinen, Olli-Pekka; Savolainen, Hannu

2008-01-01

A sample of 523 Chinese university students was given a questionnaire on their attitudes towards the inclusion of children with disabilities into regular classrooms. Factor analysis, analysis of variance, t-test and correlations were used to assess the respondents' general attitude towards inclusion, the factor structure of the attitudes, the…

Micromechanical exfoliation of two-dimensional materials by a polymeric stamp

International Nuclear Information System (INIS)

Costa, M C Ferraz da; Ribeiro, H B; Kessler, F; Souza, E A T de; Fechine, G J M

2016-01-01

In this work, an alternative technique to the traditional micromechanical exfoliation of two-dimensional materials is proposed, consisting of isolated flakes of graphite and molybdenum disulphide onto polymeric surfaces films. The set made up of polymer and flakes is fabricated by using a hot-press machine called polymeric stamp. The polymeric stamp was used to allocate flakes and also to allow the exfoliation process to take place just in one face of isolated flake. Optical microscopy, Raman spectroscopy and photoluminescence spectroscopy results showed that multilayers, bilayers and single layers of graphene and MoS 2 were obtained by using a polymeric stamp as tool for micromechanical exfoliation. These crystals were more easily found because the exfoliation process concentrates them in well-defined locations. The results prove the effectiveness of the method by embedding two-dimensional materials into polymers to fabricate fewer layers crystals in a fast, economic and clean way. (paper)

Micromechanical exfoliation of two-dimensional materials by a polymeric stamp

Science.gov (United States)

Ferraz da Costa, M. C.; Ribeiro, H. B.; Kessler, F.; de Souza, E. A. T.; Fechine, G. J. M.

2016-02-01

In this work, an alternative technique to the traditional micromechanical exfoliation of two-dimensional materials is proposed, consisting of isolated flakes of graphite and molybdenum disulphide onto polymeric surfaces films. The set made up of polymer and flakes is fabricated by using a hot-press machine called polymeric stamp. The polymeric stamp was used to allocate flakes and also to allow the exfoliation process to take place just in one face of isolated flake. Optical microscopy, Raman spectroscopy and photoluminescence spectroscopy results showed that multilayers, bilayers and single layers of graphene and MoS2 were obtained by using a polymeric stamp as tool for micromechanical exfoliation. These crystals were more easily found because the exfoliation process concentrates them in well-defined locations. The results prove the effectiveness of the method by embedding two-dimensional materials into polymers to fabricate fewer layers crystals in a fast, economic and clean way.

Oxidative polymerization of lignins by laccase in water-acetone mixture.

Science.gov (United States)

Fiţigău, Ionița Firuța; Peter, Francisc; Boeriu, Carmen Gabriela

2013-01-01

The enzymatic oxidative polymerization of five technical lignins with different molecular properties, i.e. Soda Grass/Wheat straw Lignin, Organosolv Hardwood Lignin, Soda Wheat straw Lignin, Alkali pretreated Wheat straw Lignin, and Kraft Softwood was studied. All lignins were previously fractionated by acetone/water 50:50 (v/v) and the laccase-catalyzed polymerization of the low molecular weight fractions (Mw Reactivity of lignin substrates in laccase-catalyzed reactions was determined by monitoring the oxygen consumption. The oxidation reactions in 50% acetone in water mixture proceed with high rate for all tested lignins. Polymerization products were analyzed by size exclusion chromatography, FT-IR, and (31)P-NMR and evidence of important lignin modifications after incubation with laccase. Lignin polymers with higher molecular weight (Mw up to 17500 g/mol) were obtained. The obtained polymers have potential for applications in bioplastics, adhesives and as polymeric dispersants.

C1 Polymerization: a unique tool towards polyethylene-based complex macromolecular architectures

KAUST Repository

Wang, De

2017-05-09

The recent developments in organoborane initiated C1 polymerization (chain grows by one atom at a time) of ylides opens unique horizons towards well-defined/perfectly linear polymethylenes (equivalent to polyethylenes, PE) and PE-based complex macromolecular architectures. The general mechanism of C1 polymerization (polyhomologation) involves the formation of a Lewis complex between a methylide (monomer) and a borane (initiator), followed by migration/insertion of a methylene into the initiator and after oxidation/hydrolysis to afford OH-terminated polyethylenes. This review summarizes efforts towards conventional and newly discovered borane-initiators and ylides (monomers), as well as a combination of polyhomologation with other polymerization methods. Initial efforts dealing with C3 polymerization and the synthesis of the first C1/C3 copolymers are also given. Finally, some thoughts for the future of these polymerizations are presented.

Pre-irradiation induced emulsion graft polymerization of acrylonitrile onto polyethylene nonwoven fabric

International Nuclear Information System (INIS)

Liu Hanzhou; Yu Ming; Deng Bo; Li Linfan; Jiang Haiqing; Li Jingye

2012-01-01

Acrylonitrile has been widely used in the modification of polymers by graft polymerization. In the present work, pre-irradiation induced emulsion graft polymerization method is used to introduce acrylonitrile onto PE nonwoven fabric instead of the traditional reaction in organic solvents system. The degree of grafting (DG) is measured by gravimetric method and the kinetics of the graft polymerization is studied. The existence of the graft chains is proven by Fourier transform infrared spectroscopy (FT-IR) analysis. Thermal stability of the grafted polymer is measured by Thermogravimetric analysis (TGA). - Highlights: → Acrylonitrile is grafted onto pre-irradiated polyethylene (PE) nonwoven fabrics. → Emulsion system is applied, for the graft polymerization avoids organic solvent. → Kinetic of the pre-irradiation induced graft polymerization is studied. → Optimal condition is determined at the temperature below the b.p. of acrylonitrile.

C1 Polymerization: a unique tool towards polyethylene-based complex macromolecular architectures

KAUST Repository

Wang, De; Zhang, Zhen; Hadjichristidis, Nikolaos

2017-01-01

The recent developments in organoborane initiated C1 polymerization (chain grows by one atom at a time) of ylides opens unique horizons towards well-defined/perfectly linear polymethylenes (equivalent to polyethylenes, PE) and PE-based complex macromolecular architectures. The general mechanism of C1 polymerization (polyhomologation) involves the formation of a Lewis complex between a methylide (monomer) and a borane (initiator), followed by migration/insertion of a methylene into the initiator and after oxidation/hydrolysis to afford OH-terminated polyethylenes. This review summarizes efforts towards conventional and newly discovered borane-initiators and ylides (monomers), as well as a combination of polyhomologation with other polymerization methods. Initial efforts dealing with C3 polymerization and the synthesis of the first C1/C3 copolymers are also given. Finally, some thoughts for the future of these polymerizations are presented.

Homogenisation of sulphide inclusions within diamonds: A new approach to diamond inclusion geochemistry

Science.gov (United States)

McDonald, Iain; Hughes, Hannah S. R.; Butler, Ian B.; Harris, Jeffrey W.; Muir, Duncan

2017-11-01

Base metal sulphide (BMS) inclusions in diamonds provide a unique insight into the chalcophile and highly siderophile element composition of the mantle. Entombed within their diamond hosts, these provide a more robust (closed system) sample, from which to determine the trace element, Re-Os and S-isotopic compositions of the mantle than mantle xenoliths or orogenic peridotites, as they are shielded from alteration during ascent to the Earth's crust and subsequent surface weathering. However, at temperatures below 1100 °C some BMS inclusions undergo subsolidus re-equilibration from an original monosulphide solid solution (Mss) and this causes fractionation of the major and trace elements within the inclusions. Thus to study the subjects noted above, current techniques require the entire BMS inclusion to be extracted for analyses. Unfortunately, 'flaking' of inclusions during break-out is a frequent occurrence and hence the risk of accidentally under-sampling a portion of the BMS inclusion is inherent in current practices. This loss may have significant implications for Re-Os isotope analyses where incomplete sampling of a Re-rich phase, such as chalcopyrite that typically occurs at the outer margins of BMS inclusions, may induce significant bias in the Re-Os and 187Os/188Os measurements and resulting model and isochron ages. We have developed a method for the homogenisation of BMS inclusions in diamond prior to their break-out from the host stone. Diamonds are heated to 1100 °C and then quenched to chemically homogenise any sulphide inclusions for both major and trace elements. Using X-ray Computed Microtomography (μCT) we determine the shape and spatial setting of multiple inclusions within a host stone and crucially show that the volume of a BMS inclusion is the same both before and after homogenisation. We show that the homogenisation process significantly reduces the inherent variability of in situ analysis when compared with unhomogenised BMS, thereby

Lipase-catalyzed ring-opening polymerization of lactones to polyesters and its mechanistic aspects.

Science.gov (United States)

Namekawa, S; Suda, S; Uyama, H; Kobayashi, S

1999-01-01

Lipase catalysis induced a ring-opening polymerization of lactones with different ring-sizes. Small-size (four-membered) and medium-size lactones (six- and seven-membered) as well as macrolides (12-, 13-, 16-, and 17-membered) were subjected to lipase-catalyzed polymerization. The polymerization behaviors depended primarily on the lipase origin and the monomer structure. The macrolides showing much lower anionic polymerizability were enzymatically polymerized faster than epsilon-caprolactone. The granular immobilized lipase derived from Candida antartica showed extremely efficient catalysis in the polymerization of epsilon-caprolactone. Single-step terminal functionalization of the polyester was achieved by initiator and terminator methods. The enzymatic polymerizability of lactones was quantitatively evaluated by Michaelis-Menten kinetics.

Limitations of inclusive fitness.

Science.gov (United States)

Allen, Benjamin; Nowak, Martin A; Wilson, Edward O

2013-12-10

Until recently, inclusive fitness has been widely accepted as a general method to explain the evolution of social behavior. Affirming and expanding earlier criticism, we demonstrate that inclusive fitness is instead a limited concept, which exists only for a small subset of evolutionary processes. Inclusive fitness assumes that personal fitness is the sum of additive components caused by individual actions. This assumption does not hold for the majority of evolutionary processes or scenarios. To sidestep this limitation, inclusive fitness theorists have proposed a method using linear regression. On the basis of this method, it is claimed that inclusive fitness theory (i) predicts the direction of allele frequency changes, (ii) reveals the reasons for these changes, (iii) is as general as natural selection, and (iv) provides a universal design principle for evolution. In this paper we evaluate these claims, and show that all of them are unfounded. If the objective is to analyze whether mutations that modify social behavior are favored or opposed by natural selection, then no aspect of inclusive fitness theory is needed.

Optical investigations of various polymeric materials used in dental technology

Science.gov (United States)

Negrutiu, Meda Lavinia; Sinescu, Cosmin; Topala, Florin Ionel; Ionita, Ciprian; Goguta, Luciana; Marcauteanu, Corina; Rominu, Mihai; Podoleanu, Adrian Gh.

2011-10-01

Dental prosthetic restorations have to satisfy high stress as well as aesthetic requirements. In order to avoid deficiencies of dental prostheses, several alternative systems and procedures were imagined, directly related to the material used and also to the manufacturing technology. Increasing the biomechanical comportment of polymeric materials implies fiber reinforcing. The different fibers reinforcing products made very difficult the evaluation of their performances and biomechanical properties analysis. There are several known methods which are used to assess the quality of dental prostheses, but most are invasive. These lead to the destruction of the samples and often no conclusion could be drawn in the investigated areas of interest. Using a time domain en-face OCT system, we have recently demonstrated real time thorough evaluation of quality of various dental treatments. The aim of this study was to assess the quality of various polymeric materials used in dental technology and to validate the en face OCT imagistic evaluation of polymeric dental prostheses by using scanning electron microscopy (SEM) and microcomputer tomography (μCT). SEM investigations evidenced the nonlinear aspect of the interface between the polymeric material and the fiber reinforcement and materials defects in some samples. The results obtained by microCT revealed also some defects inside the polymeric materials and at the interfaces with the fiber reinforcement. The advantages of the OCT method consist in non-invasiveness and high resolution. In addition, en face OCT investigations permit visualization of the more complex stratified structure at the interface between the polymeric material and the fiber reinforcement.

Polymerization by radiation. Application

International Nuclear Information System (INIS)

Romero, M.; Fernandez Miranda, J.

1997-01-01

Achieved results of the research work done in the field of radiation polymerization are summarized. Developing new chromatographic matrices, the radiation grafting of Glycidyl methacrylate on the surface of Low Density Polyethylene beads was studied. The dependence of both, the grafted degree and width of the grafted layer, with the radiation dose applied, is presented

Continuous fabrication of polymeric vesicles and nanotubes with fluidic channe

NARCIS (Netherlands)

Peng, F.; Deng, N.-N.; Tu, Y.; van Hest, J.C.M.; Wilson, D.A.

2017-01-01

Fluidic channels were employed to induce the self-assembly of poly(ethylene glycol)-b-polystyrene into polymeric vesicles and nanotubes. The laminar flow in the device enables controlled diffusion of two miscible liquids at the phase boundary, leading to the formation of homogeneous polymeric

Deposition of a thin electro-polymerized organic film on iron surface

International Nuclear Information System (INIS)

Lecayon, Gerard

1980-01-01

We use an electrochemical method to prepare a polymerized thin film, obtained from acrylonitrile in a solution of acetonitrile and tetraethylammonium perchlorate. The films are deposited on oxidized iron electrodes, with a surface area varying from a few mm to several cm, their thickness ranges from ten A to thousand A. This result is obtained by controlling the evolution of reactions: duplication, hydrogenation, polymerization which occur during the electrochemical reduction of acrylonitrile. The choice of suitable experimental conditions enhances the polymerization and increases the adherence of the polymer on the electrode. The usual methods of surface studies: S.E.M., A.E.S., S.I.M.S., permit the characterization of the electrode surface and the chemical composition of the deposit films. The molecular structure of polymer, and its evolution under aging or heating was studied by infrared multi-reflection spectroscopy. Very good correlation exists between the electrochemical characteristic: I = f(t), the initial surface state of the electrodes, and the homogeneity of the electro-polymerized films. Diagrams corresponding to mechanisms of different stages of electro-polymerization are proposed. (author) [fr

Nonlinear viscoelasticity of pre-compressed layered polymeric composite under oscillatory compression

KAUST Repository

Xu, Yangguang

2018-05-03

Describing nonlinear viscoelastic properties of polymeric composites when subjected to dynamic loading is essential for development of practical applications of such materials. An efficient and easy method to analyze nonlinear viscoelasticity remains elusive because the dynamic moduli (storage modulus and loss modulus) are not very convenient when the material falls into nonlinear viscoelastic range. In this study, we utilize two methods, Fourier transform and geometrical nonlinear analysis, to quantitatively characterize the nonlinear viscoelasticity of a pre-compressed layered polymeric composite under oscillatory compression. We discuss the influences of pre-compression, dynamic loading, and the inner structure of polymeric composite on the nonlinear viscoelasticity. Furthermore, we reveal the nonlinear viscoelastic mechanism by combining with other experimental results from quasi-static compressive tests and microstructural analysis. From a methodology standpoint, it is proved that both Fourier transform and geometrical nonlinear analysis are efficient tools for analyzing the nonlinear viscoelasticity of a layered polymeric composite. From a material standpoint, we consequently posit that the dynamic nonlinear viscoelasticity of polymeric composites with complicated inner structures can also be well characterized using these methods.

Controlling the Plasma-Polymerization Process of N-Vinyl-2-pyrrolidone

DEFF Research Database (Denmark)

Norrman, Kion; Winther-Jensen, Bjørn

2005-01-01

N-vinyl-2-pyrrolidone was plasma-polymerized on glass substrates using a pulsed AC plasma. Pulsed AC plasma produces a chemical surface structure different from that produced by conventional RF plasma; this is ascribed to the different power regimes used. A high degree of control over the structure...... of the chemical surface was obtained using pulsed AC plasma, as shown by ToF-SIMS. It is demonstrated how the experimental conditions to some extent control the chemical structure of the plasma-polymerized film, e.g., film thickness, density of post-plasma-polymerized oligomeric chains, and the density of intact...

A Kinetic Study of the Emulsion Polymerization of Vinyl Acetate

DEFF Research Database (Denmark)

Friis, N.; Nyhagen, L.

1973-01-01

The emulsion polymerization of vinyl acetate was studied at 50°C. It was found that the rate of polymerization was proportional to the 0.5 power of the initiator concentration and the 0.25 power of the number of particles. The number of particles was proportional to the power 0.5 ± 0.......05 of the emulsifier concentration, but independent of the initiator concentration. The limiting viscosity number of the polymers produced was independent of the initiator concentration and number of polymer particles. It is suggested that the mechanism of vinyl acetate emulsion polymerization is similar...

Polymeric drugs: Advances in the development of pharmacologically active polymers

Science.gov (United States)

Li, Jing; Yu, Fei; Chen, Yi; Oupický, David

2015-01-01

Synthetic polymers play a critical role in pharmaceutical discovery and development. Current research and applications of pharmaceutical polymers are mainly focused on their functions as excipients and inert carriers of other pharmacologically active agents. This review article surveys recent advances in alternative pharmaceutical use of polymers as pharmacologically active agents known as polymeric drugs. Emphasis is placed on the benefits of polymeric drugs that are associated with their macromolecular character and their ability to explore biologically relevant multivalency processes. We discuss the main therapeutic uses of polymeric drugs as sequestrants, antimicrobials, antivirals, and anticancer and anti-inflammatory agents. PMID:26410809

Self-folding polymeric containers for encapsulation and delivery of drugs.

Science.gov (United States)

Fernandes, Rohan; Gracias, David H

2012-11-01

Self-folding broadly refers to self-assembly processes wherein thin films or interconnected planar templates curve, roll-up or fold into three dimensional (3D) structures such as cylindrical tubes, spirals, corrugated sheets or polyhedra. The process has been demonstrated with metallic, semiconducting and polymeric films and has been used to curve tubes with diameters as small as 2nm and fold polyhedra as small as 100nm, with a surface patterning resolution of 15nm. Self-folding methods are important for drug delivery applications since they provide a means to realize 3D, biocompatible, all-polymeric containers with well-tailored composition, size, shape, wall thickness, porosity, surface patterns and chemistry. Self-folding is also a highly parallel process, and it is possible to encapsulate or self-load therapeutic cargo during assembly. A variety of therapeutic cargos such as small molecules, peptides, proteins, bacteria, fungi and mammalian cells have been encapsulated in self-folded polymeric containers. In this review, we focus on self-folding of all-polymeric containers. We discuss the mechanistic aspects of self-folding of polymeric containers driven by differential stresses or surface tension forces, the applications of self-folding polymers in drug delivery and we outline future challenges. Copyright © 2012 Elsevier B.V. All rights reserved.

Preparation of molecularly imprinted polymers for strychnine by precipitation polymerization and multistep swelling and polymerization and their application for the selective extraction of strychnine from nux-vomica extract powder.

Science.gov (United States)

Nakamura, Yukari; Matsunaga, Hisami; Haginaka, Jun

2016-04-01

Monodisperse molecularly imprinted polymers for strychnine were prepared by precipitation polymerization and multistep swelling and polymerization, respectively. In precipitation polymerization, methacrylic acid and divinylbenzene were used as a functional monomer and crosslinker, respectively, while in multistep swelling and polymerization, methacrylic acid and ethylene glycol dimethacrylate were used as a functional monomer and crosslinker, respectively. The retention and molecular recognition properties of the molecularly imprinted polymers prepared by both methods for strychnine were evaluated using a mixture of sodium phosphate buffer and acetonitrile as a mobile phase by liquid chromatography. In addition to shape recognition, ionic and hydrophobic interactions could affect the retention of strychnine in low acetonitrile content. Furthermore, molecularly imprinted polymers prepared by both methods could selectively recognize strychnine among solutes tested. The retention factors and imprinting factors of strychnine on the molecularly imprinted polymer prepared by precipitation polymerization were 220 and 58, respectively, using 20 mM sodium phosphate buffer (pH 6.0)/acetonitrile (50:50, v/v) as a mobile phase, and those on the molecularly imprinted polymer prepared by multistep swelling and polymerization were 73 and 4.5. These results indicate that precipitation polymerization is suitable for the preparation of a molecularly imprinted polymer for strychnine. Furthermore, the molecularly imprinted polymer could be successfully applied for selective extraction of strychnine in nux-vomica extract powder. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Research regarding biodegradable properties of food polymeric products under microorganism activity

Science.gov (United States)

Opran, Constantin; Lazar, Veronica; Fierascu, Radu Claudiu; Ditu, Lia Mara

2018-02-01

Aim of this research is the structural analysis by comparison of the biodegradable properties of two polymeric products made by non-biodegradable polymeric material (polypropylene TIPPLEN H949 A) and biodegradable polymeric material (ECOVIO IS 1335), under microorganism activity in order to give the best solution for the manufacture of food packaging biodegradable products. It presents the results of experimental determinations on comparative analysis of tensile strength for the two types of polymers. The sample weight variations after fungal biodegradation activity revealed that, after 3 months, there are no significant changes in polymeric substratum for non-biodegradable polymeric. The microscopically analysis showed that the fungal filaments did not strongly adhered on the non-biodegradable polymeric material, instead, both filamentous fungi strains adhered and covered the surface of the biodegradable sample with germinated filamentous conidia. The spectral analysis of polymer composition revealed that non-biodegradable polymer polypropylene spectra are identical for control and for samples that were exposed to fungal activity, suggesting that this type of sample was not degraded by the fungi strains. Instead, for biodegradable polymer sample, it was observed significant structural changes across multiple absorption bands, suggesting enzyme activity manifested mainly by Aspergillus niger strain. Structural analysis of interdisciplinary research results, lead, to achieving optimal injection molded technology emphasizing technological parameters, in order to obtain food packaging biodegradable products.

Inclusive innovation: a research project on the inclusion of social responsibility

NARCIS (Netherlands)

Nijhof, A.H.J.; Fisscher, O.A.M.; de Bakker, F.G.A.

2001-01-01

The research project 'Inclusive Innovation' aims at stimulating dialogue about inclusion of social responsibility based on universal human rights in the conduct of business. This dialogue concerns both the communication within the organisation and between the organisation and interested parties in

High performance nature of biodegradable polymeric nanocomposites for oil-well drilling fluids

Directory of Open Access Journals (Sweden)

Tarek M. Madkour

2016-06-01

Full Text Available Multi-walled carbon nanotube (MWCNT and graphene nanoplatelet reinforced thermoplastic poly(lactic acid (PLA biodegradable nanocomposites were designed and prepared using solution casting techniques. The prepared biodegradable polymers are expected to provide an environmentally friendly alternative to petroleum-based polymers. Both nanocomposite systems exhibited better thermal stability and improved mechanical performance over the unreinforced polymer exhibiting excellent strength and degradability. The addition of graphene nanofiller in varied amounts was aimed to enhance the thermal and mechanical properties of the nanocomposites even further and incorporate the outstanding characteristics of graphene nanoplatelets into the nanocomposites. The polymeric nanocomposites showed also superior advantages for oil drilling relevances, automotive lubricating purposes, membrane technology and food packaging. Scanning electron microscopy images indicated a homogeneous dispersion of the nanofiller within the polymeric matrix at low filler loadings and a cluster formation at higher loadings that could be responsible for the polymeric matrix movement restrictions. The enthalpy of mixing (the polymer and the nanofiller measured could explain the cause of the repulsive interactions between the nanoparticles and the polymeric chains, which created an additional excluded volume that the polymeric segments were restricted to occupy, thus forcing the conformational characteristics of the polymeric chains to deviate away from those of the bulk chains. The prepared polymeric nano composites (poly lactic acid carbon nano tube and poly lactic acid graphene nanoplatelets were utilized in the formulation of oil-base mud as a viscosifier. The rheological, filtration properties and electrical stability of the oil based mud formulation with the new polymeric nanocomposite were studied and the result compared to the oil-based mud formulation with commercial viscosifier.

Evaluation of metal-polymeric fixed partial prosthesis using optical coherence tomography

Science.gov (United States)

Sinescu, C.; Negrutiu, M. L.; Duma, V. F.; Marcauteanu, C.; Topala, F. I.; Rominu, M.; Bradu, A.; Podoleanu, A. Gh.

2013-11-01

Metal-Polymeric fixed partial prosthesis is the usual prosthetic treatment for many dental patients. However, during the mastication the polymeric component of the prosthesis is fractured and will be lost. This fracture is caused by the material defects or by the fracture lines trapped inside the esthetic components of the prosthesis. This will finally lead to the failure of the prosthetic treatment. Nowadays, there is no method of identification and forecast for the materials defects of the polymeric materials. The aim of this paper is to demonstrate the capability of Optical Coherence Tomography (OCT) as a non-invasive clinical method that can be used for the evaluation of metal-polymeric fixed partial prostheses. Twenty metal-polymeric fixed partial prostheses were used for this study. The esthetic component of the prostheses has been Adoro (Ivoclar). Optical investigations of the metal prostheses have revealed no material defects or fracture lines. All the prostheses were temporary cemented in the oral cavities of the patients for six month. The non-invasive method used for the investigations was OCT working in Time Domain mode at 1300 nm. The evaluations of the prostheses were performed before and after their cementation in the patient mouths. All the imagistic results were performed in 2D and than in 3D, after the reconstruction. The results obtained after the OCT evaluation allowed for the identification of 4 metal-polymeric fixed partial prostheses with material defects immediately after finishing the technological procedures. After 6 month in the oral environment other 3 fixed partial prostheses revealed fracture lines. In conclusion, OCT proved to be a valuable tool for the noninvasive evaluation of the metal-polymeric fixed partial prostheses.

Polystyrene/magnesium hydroxide nanocomposite particles prepared by surface-initiated in-situ polymerization

International Nuclear Information System (INIS)

Liu Hui; Yi Jianhong

2009-01-01

In order to avoid their agglomeration and incompatibility with hydrophobic polystyrene substrate, magnesium hydroxide nanoparticles were encapsulated by surface-initiated in-situ polymerization of styrene. The process contained two steps: electrostatic adsorption of initiator and polymerization of monomer on the surface of magnesium hydroxide. It was found that high adsorption ratio in the electrostatic adsorption of initiator could be attained only in acidic region, and the adsorption belonged to typical physical process. Compared to traditional in-situ polymerization, higher grafting ratio was obtained in surface-initiated in-situ polymerization, which can be attributed to weaker steric hindrance. Both Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM) indicated that polystyrene/magnesium hydroxide nanocomposite particles had been successfully prepared by surface-initiated in-situ polymerization. The resulting samples were also analyzed and characterized by means of contact angle testing, dispersibility evaluation and thermogravimetric analysis

NATO Advanced Research Workshop on Frontiers in Polymerization Catalysis and Polymer Synthesis

CERN Document Server

Guyot, A

1987-01-01

Due to their specific properties, polymers with well-defined structures have been receiving increasing attention over the last several years. Owing to the wide variability of their properties, these specialty polymers have been used in various areas from biomedical engineering to electronics or energy applications. The synthesis of such polymers necessi­ tates the use of new methods of polymerization which derived from an insight into the mechanism of polymerization reactions. A NATO Advanced Research Workshop on "Frontiers in Polymerization Catalysis and Polymer Synthesis" was held in BANDOl (FRANCE) in February 1987. Its aim was to assess the new polymerization methods, as well as the latest advances in the mechanisms of conventional polymerization reactions together with their applications to the synthesis of new macromolecular structures. The financial support from the NATO Scientific Affairs Division which covered the "lecturers' accomodation and travel expenses as well as the organization charges of th...

Financial inclusion: Policies and practices

Directory of Open Access Journals (Sweden)

Thankom Arun

2015-12-01

Full Text Available As a key enabler for development, financial inclusion is firmly placed on the agenda of most governments as a key policy priority. Against this background, this round table provides a global and regional perspective on the policies and practices of financial inclusion. Using macro data, the collection reveals the diversity in the efforts towards achieving financial inclusion and the need for a progressive approach in financial inclusion. Further to this, the round table provides the regional perspectives on the policies and practices of financial inclusion in India, South Africa, and Australia.

Photo-polymerization of photocurable resins containing polyhedral oligomeric silsesquioxane methacrylate

International Nuclear Information System (INIS)

Lin, Ho-May; Wu, Shi-Yin; Chang, Feng-Chih; Yen, Ying-Chieh

2011-01-01

Photocurable resins, bisphenol A propoxylate glycerolate diacrylate (BPA-PGDA, containing two hydroxyl) and bisphenol A propoxylate diacrylate (BPA-PDA), with fixed photoinitiator (Irgacure 907) concentration and various contents of methacrylisobutyl polyhedral oligomeric silsesquioxane (MI-POSS) were prepared and characterized by FTIR spectroscopy, scanning electron microscope and differential photocalorimetry. The MI-POSS molecules form crystals or aggregated particles in the cured resin matrix. The BPA-PGDA series photocurable resins show higher viscosity and lower photo-polymerization reactivity than the BPA-PDA series resins. The photo-polymerization rate and conversion of BPA-PGDA series are improved with increasing MI-POSS content. On the contrary, the photo-polymerization behavior of BPA-PDA series photocurable resins remains nearly unchanged by the addition of MI-POSS. Hydrogen-bonding interaction between the hydroxyl of BPA-PGDA and the siloxane of MI-POSS tends to attract and concentrate these acrylate double bonds around MI-POSS particles and thus enhances the photo-polymerization rate and conversion.

Noncovalent assembly. A rational strategy for the realization of chain-growth supramolecular polymerization.

Science.gov (United States)

Kang, Jiheong; Miyajima, Daigo; Mori, Tadashi; Inoue, Yoshihisa; Itoh, Yoshimitsu; Aida, Takuzo

2015-02-06

Over the past decade, major progress in supramolecular polymerization has had a substantial effect on the design of functional soft materials. However, despite recent advances, most studies are still based on a preconceived notion that supramolecular polymerization follows a step-growth mechanism, which precludes control over chain length, sequence, and stereochemical structure. Here we report the realization of chain-growth polymerization by designing metastable monomers with a shape-promoted intramolecular hydrogen-bonding network. The monomers are conformationally restricted from spontaneous polymerization at ambient temperatures but begin to polymerize with characteristics typical of a living mechanism upon mixing with tailored initiators. The chain growth occurs stereoselectively and therefore enables optical resolution of a racemic monomer. Copyright © 2015, American Association for the Advancement of Science.

A surface science model for the Phillips ethylene polymerization catalyst : thermal activation and polymerization activity

NARCIS (Netherlands)

Kimmenade, van E.M.E.; Kuiper, A.E.T.; Tamminga, Y.; Thuene, P.C.; Niemantsverdriet, J.W.

2004-01-01

A series of CrOx/SiO2/Si(100) model catalysts were tested for ethylene polymerization activity, varying chromium loading, and calcination temperature. Chromium coverage of the model catalyst, quantified by Rutherford backscattering spectrometry, decreases with increasing calcination temperature as

Oligonucleotides as probes for studying polymerization reactions in dilute aqueous solution