WorldWideScience

Sample records for crystallographic preferred orientation

  1. Extruded electroactive fibers: preferred crystallographic orientation

    Science.gov (United States)

    Strock, Harold B.; Pascucci, Marina R.; Bystricky, Pavel

    2001-07-01

    Electroactive fibers of preferred macro crystalline orientation and ultimately single crystal structure are goals of the research discussed in this paper. Four compositions are under evaluation; lead magnesium niobate- lead titanate solid solution, PMN-31PT, an incongruently melting near-morphotropic phase boundary piezoelectric composition; PMN-10PT, an electrostrictor composition; and two lead free compositions in the sodium bismuth titanate- barium titanate solid solution, NbiT-BaT, family, both congruently melting, one electrostrictor and one piezoelectric. The efficacy of seed crystals in stimulating oriented crystal growth is being evaluated in the lead-based PMN-31PT system. Sub-micron reactive precursor powders of high chemical potential are being evaluated as matrix material. Direct fiber and ribbon extrusion have been shown to orient high chemical potential are being evaluated as matrix material. Direct fiber and ribbon extrusion have been shown to orient high chemical potential are being evaluated as matrix material. Direct fiber and ribbon extrusion have been shown to orient prismatic, needle and platelet shaped seed crystals. Extrusion orifice, seed and initial matrix particle size have not influenced the degree of seed orientation within the tested bounds of our experimental parameters. Non-equilibrium sintering conditions near the melting points of all four compositions noted above will be used to generate exaggerated grain growth under seeded and self-seeding conditions. In the PMN-31PT system, an as yet uncharacterized melt phase appears to stimulate rapid crystal growth, the orientation of which shall be determined by x-ray back reflection Laue methods. Analyses of fiber composition and grain orientation are ongoing. Results to-date will be reported. Analyses of fiber quality and performance, measured using single fiber P-E loop testing, are presented. Loops of sufficient quality to warrant fiber evaluation in active fiber composite packs have

  2. Crystallographic preferred orientation and deformation of deep Earth minerals

    Science.gov (United States)

    Kaercher, Pamela Michelle

    This thesis aims to provide further insight into crystallographic preferred orientation (CPO) and deformation mechanisms active at high pressure. Preferred orientation of iron-rich magnesiowustite (Mg,Fe)O, a major mantle mineral phase, stishovite (SiO2), the high pressure polymorph of quartz that is likely present in the lower crust and mantle, and in NaMgF3 + NaCl, an analog system to lower mantle minerals MgSiO3 + MgO, have been examined with synchrotron X-ray diffraction while at high pressure in either a diamond anvil cell or a multianvil press. Magnesiowustite, (Mg0.08Fe0.88)O, and wustite, Fe0.94O, were compressed up to 37 GPa at ambient temperature in diamond anvil cells (DAC) at the Advanced Light Source (ALS). X-ray diffraction patterns were taken in situ in radial geometry in order to study the evolution of CPO through the cubic-to-rhombohedral phase transition. Under uniaxial stress in the DAC, cubic texture developed (i.e. {100} c planes aligned perpendicular to the compression direction). Variant selection of preferred orientation was observed immediately following the transition to the rhombohedral phase. Upon decompression in the DAC, FeO reverted back to cubic symmetry and the cubic texture reappeared, demonstrating that the transition is reversible and has texture memory. The crystal structure of the high pressure SiO2 polymorph stishovite has been studied in detail, but little is known about texture development during deformation, which provides information for understanding subduction of quartz-bearing crustal rocks into the mantle. Radial DAC experiments were done at the ALS and the Advanced Photon Source (APS) while collecting X-ray diffraction patterns in radial geometry to examine in situ development of CPO. Starting pressure in the sample chamber was still in the quartz stability field, and compression of quartz produced a weak texture, likely due to Dauphine twinning. Following compression of quartz into the stishovite stability field

  3. Evolution of the preferred crystallographic orientation across the thickness of nickel electrodeposits

    DEFF Research Database (Denmark)

    Alimadadi, Hossein; da Silva Fanta, Alice Bastos; Somers, Marcel A. J.;

    Numerous industrial applications of nickel electrodeposits, like for example as microcomponents, essentially depend on their preferred crystallographic orientation. As a function of the electrodeposition conditions, the microstructure can be tailored with respect to the size, shape...... for such advanced investigations. The present work reports on the evolution of the preferred crystallographic orientation on the example of various fiber textured nickel electrodeposits. Tailored electrodeposition provided nickel deposits with different fibre textures being , , and ... and crystallographic orientation of grains. Thorough microstructure characterization, however, is not straightforward, because the microstructure of electrodeposits often changes across the thickness of the deposits and numerous twin orientations even with nano-size dimensions can evolve during growth of the deposits...

  4. Preferred crystallographic orientation in the ice I ← II transformation and the flow of ice II

    Science.gov (United States)

    Bennett, K.; Wenk, H.-R.; Durham, W.B.; Stern, L.A.; Kirby, S.H.

    1997-01-01

    The preferred crystallographic orientation developed during the ice I ← II transformation and during the plastic flow of ice II was measured in polycrystalline deuterium oxide (D2O) specimens using low-temperature neutron diffraction. Samples partially transformed from ice I to II under a non-hydrostatic stress developed a preferred crystallographic orientation in the ice II. Samples of pure ice II transformed from ice I under a hydrostatic stress and then when compressed axially, developed a strong preferred orientation of compression axes parallel to (1010). A match to the observed preferred orientation using the viscoplastic self-consistent theory was obtained only when (1010) [0001] was taken as the predominant slip system in ice II.

  5. Self-assembled ultra-nanocrystalline silicon films with preferred crystallographic orientation for solar cell applications

    Science.gov (United States)

    Banerjee, Amit; Das, Debajyoti

    2015-03-01

    Using low-pressure planar inductively coupled plasma CVD at 87% H2-dilution to the SiH4 plasma, nc-Si:H films are prepared that possess preferential growth along crystallographic orientation with I220/I111 > 1.2, bonded H-content of ∼5.5 at.%, a low microstructure factor of ∼0.56, along with a reasonably high σD ∼ 5.2 × 10-4 S cm-1, ΔE ∼ 143 meV and σPh ∼ 1.4 × 10-3 S cm-1. The growth of the nc-Si:H network has been optimized to a moderately high nanocrystallinity (∼68%), with an average grain size of ∼8 nm. The overall network comprises a significant fraction of ultra-nanocrystalline component, Xunc/Xnc ∼ 0.47, which are dominantly inhabited by the thermodynamically preferred crystallographic orientation that provides convenient electrical transport perpendicular to the film surface and subsequently could facilitate photovoltaic performance. The cross-sectional view of the fracture surface demonstrates columnar structures, closely correlated to the favored growth of the nanocrystallites along crystallographic orientation that retains direction perpendicular to the substrate surface. The underlying phenomena could be demonstrated as a consequence of preferential growth induced by high atomic H density present in the planar inductively coupled SiH4 plasma obtained via much lower H2-dilution compared to that realized in conventional capacitively coupled plasma-CVD. The nc-Si:H films with precise material properties as well as the allied low-pressure ICP-CVD growth process could be of significant use in further progress of nc-Si solar cells.

  6. Microstructures and crystallographic preferred orientation of anorthosites from Oman ophiolite and the dynamics of melt lenses

    Science.gov (United States)

    Morales, Luiz F. G.; Boudier, FrançOise; Nicolas, Adolphe

    2011-04-01

    Microstructures and crystallographic preferred orientation (CPO) of anorthosite samples interlayered in the upper and lower gabbro sections in the Oman ophiolite were analyzed in this paper. In the anorthosites registering the dynamics of the melt lenses, foliation is flat lying and starts to develop a few meters below the root zone of the sheeted dike complex (RZSDC). Microstructures and CPO of these rocks were developed in response to four different mechanisms: (1) density-controlled settling of plagioclase on the lens floor, (2) deposition of anorthosites related to convection currents, (3) melt compaction, and (4) uncompacted melt accumulation. In these anorthosites, the poles to (010) of plagioclase are parallel to the flow plane of convection, whereas the [100] axes and poles to (001) express the convection flow direction and the axis of convection rolls, respectively. The effect of subsidence of melt lens floor is recorded immediately below the RZSDC and is characterized by the rapid (but progressive) development of dipping foliation and lineation, reflecting the increase of deformation downsection. The degree of foliation and CPO development in the anorthosites is directly related to the distance of the center of the melt lenses before the subsidence starts. Despite the uncertain origin of the anorthosites from the lower gabbro section, all the samples lost the magmatic microstructural characteristics and presently are reequilibrated aggregates. However, they still preserve plagioclase CPO, where some of these patterns present similarities with the anorthosites from the upper gabbro section, but no evidence of intracrystalline deformation under high temperatures.

  7. Development of olivine crystallographic preferred orientation in response to strain-induced fabric geometry

    Science.gov (United States)

    Chatzaras, Vasileios; Kruckenberg, Seth C.; Cohen, Shaina M.; Medaris, L. Gordon, Jr.; Withers, Anthony C.; Bagley, Brian

    2016-04-01

    The effect of finite strain ellipsoid geometry on crystallographic preferred orientation (CPO) is well known for crustal minerals (e.g., quartz, calcite, biotite, and hornblende). In the upper mantle, however, it remains poorly constrained how strain and fabric may affect olivine CPO. We present data from a suite of 40 spinel peridotite xenoliths from Marie Byrd Land (west Antarctica), which support an interpretation that fabric geometry rather than deformation conditions control the development of olivine CPO. We use X-ray computed tomography (XRCT) to quantitatively determine spinel fabric (orientation and geometry). Olivine CPOs, determined by Electron Backscattered Diffraction (EBSD), are plotted with respect to the XRCT-derived spinel foliation and lineation; this approach allows for the accurate, and unbiased, identification of CPO symmetries and types in mantle xenoliths. The combined XRCT and EBSD data show that the xenoliths are characterized by a range of fabric geometries (from oblate to prolate) and olivine CPO patterns; we recognize the A-type, axial-[010], axial-[100], and B-type patterns. The mantle xenoliths equilibrated at temperatures 779-1198 oC, as determined by 2-Px geothermometry. Using a geotherm consistent with the stability of spinel in all xenoliths, the range of equilibration temperatures occurs at depths between 39 and 72 km. Olivine recrystallized grain size piezometry reveals differential stresses ranging 2-60 MPa. Analysis of low-angle misorientation axes show a wide range in the distribution of rotation axes, with dominant {0kl}[100] slip. We use Fourier Transform Infrared (FTIR) spectroscopy to estimate the water content in the xenolith with the B-type CPO pattern. FTIR analysis shows that the equilibrium H concentration in olivine is low (4-13 ppm H2O). Combining these data, we observe that olivine CPO symmetry is controlled neither by the deformation conditions (stress, temperature, pressure, water content) for the range of

  8. Formation of Fast-Spread Ocean Crust : Crystallographic Preferred Orientations From a Reference Lower Crust Section in the Oman Ophiolite

    Science.gov (United States)

    Ildefonse, B.; Mueller, T.; Mock, D.; Koepke, J.

    2016-12-01

    About 20 years ago, two competing models were proposed for the formation of the lower, gabbroic crust at fast-spreading ridges. The lower crust is either formed by downward flow of mushy material from the shallow axial melt lens (gabbro glacier), or by sill intrusions (sheeted sills). To further test these end-member models, we characterized the vertical distribution of Crystallographic Preferred Orientations (CPO) in Wadi Gideah gabbro section (Sumail ophiolite, Sultanate Oman), using the Electron Backscattered Diffraction (EBSD) technique. CPO were measured on 67 gabbro samples, documenting a 5 km thick section, with an average interval of 80 m between samples. EBSD data sets were processed using MTEX, a free Matlab toolbox. Average misorientation in grains (angle between each pixel orientation and mean orientation of the grain) is very low ( 0.25°). This is consistent with magmatic flow in these rocks, and the paucity of crystal-plastic overprint. The strength (J index) of plagioclase CPO increases down-section, with a more pronounced variability in the layered gabbros. For clinopyroxene, the difference between upper (foliated) and lower (layered) gabbros is stronger, with low J in upper gabbros, and higher and more variable J in lower gabbros. In upper gabbros the symmetry of plagioclase and clinopyroxene CPO progressively evolves downward to progressively more oblate. Continuing down-section, the trend reverses, with progressively more prolate CPO in lower gabbros. The crystallographic fabric variability in the lower crust section calls for distinct formation mechanisms in the upper and lower gabbros. It is consistent with a hybrid model for crustal formation (Boudier et al., 1996, doi:10.1016/0012-821X(96)00167-7). The genesis of the upper foliated gabbro can be at least partly explained by the gabbro glacier model, while the continuous emplacement of sheeted sills at various depths is a more plausible model for the lower layered gabbro section.

  9. Microstructure and crystallographic preferred orientation of polycrystalline microgarnet aggregates developed during progressive creep, recovery, and grain boundary sliding

    Science.gov (United States)

    Massey, M.A.; Prior, D.J.; Moecher, D.P.

    2011-01-01

    Optical microscopy, electron probe microanalysis, and electron backscatter diffraction methods have been used to examine a broad range of garnet microstructures within a high strain zone that marks the western margin of a major transpression zone in the southern New England Appalachians. Garnet accommodated variable states of finite strain, expressed as low strain porphyroclasts (Type 1), high strain polycrystalline aggregates (Type 2), and transitional morphologies (Type 3) that range between these end members. Type 1 behaved as rigid porphyroclasts and is characterized by four concentric Ca growth zones. Type 2 help define foliation and lineation, are characterized by three Ca zones, and possess a consistent bulk crystallographic preferred orientation of (100) symmetrical to the tectonic fabric. Type 3 show variable degrees of porphyroclast associated with aggregate, where porphyroclasts display complex compositional zoning that corresponds to lattice distortion, low-angle boundaries, and subgrains, and aggregate CPO mimics porphyroclast orientation. All aggregates accommodated a significant proportion of greenschist facies deformation through grain boundary sliding, grain rotation and impingement, and pressure solution, which lead to a cohesive behavior and overall strain hardening of the aggregates. The characteristic CPO could not have been developed in this manner, and was the result of an older phase of partitioned amphibolite facies dislocation creep, recovery including chemical segregation, and recrystallization of porphyroclasts. This study demonstrates the significance of strain accommodation within garnet and its affect on composition under a range of PT conditions, and emphasizes the importance of utilizing EBSD methods with studies that rely upon a sound understanding of garnet. ?? 2010 Elsevier Ltd.

  10. Recrystallization fabrics of sheared quartz veins with a strong pre-existing crystallographic preferred orientation from a seismogenic shear zone

    Science.gov (United States)

    Price, Nancy A.; Song, Won Joon; Johnson, Scott E.; Gerbi, Christopher C.; Beane, Rachel J.; West, David P.

    2016-07-01

    Microstructural investigations were carried out on quartz veins in schist, protomylonite, and mylonite samples from an ancient seismogenic strike-slip shear zone (Sandhill Corner shear zone, Norumbega fault system, Maine, USA). We interpret complexities in the microstructural record to show that: (1) pre-existing crystallographic preferred orientations (CPO) in the host rock may persist in the new CPO patterns of the shear zone and (2) the inner and outer parts of the shear zone followed diverging paths of fabric development. The host rocks bounding the shear zone contain asymmetrically-folded quartz veins with a strong CPO. These veins are increasingly deformed and recrystallized with proximity to the shear zone core. Matrix-accommodated rotation and recrystallization may position an inherited c-axis maximum in an orientation coincident with rhomb or basal slip. This inherited CPO likely persists in the shear zone fabric as a higher concentration of poles in one hemisphere of the c-axis pole figure, leading to asymmetric crossed girdle or paired maxima c-axis patterns about the foliation plane. Three observed quartz grain types indicate a general trend of localization with decreasing temperature: (1) large (> 100 μm), low aspect ratio (<~5) and (2) high aspect ratio (~ 5-20) grains overprinted by (3) smaller (<~80 μm), low aspect ratio (<~4) grains through subgrain rotation-dominated recrystallization. In the outer shear zone, subgrain rotation recrystallization led to a well-developed c-axis crossed girdle pattern. In the inner shear zone, the larger grains are completely overprinted by smaller grains, but the CPO patterns are relatively poorly developed and are associated with distinctively different misorientation angle histogram profiles ("flat" neighbor-pair profile with similar number fraction for angles from 10 to 90°). This may reflect the preferential activation of grain size sensitive deformation processes in the inner-most part of the shear zone

  11. Crystallographic Fabrics, Grain Boundary Microstructure and Shape Preferred Orientation of Deformed Banded Iron Formations and their Significance for Deformation Interpretation

    Science.gov (United States)

    Ávila, Carlos Fernando; Graça, Leonardo; Lagoeiro, Leonardo; Ferreira, Filippe

    2016-04-01

    The characterization of grain boundaries and shapes along with crystallographic preferred orientations (CPOs) are a key aspect of investigations of rock microstructures for their correlation with deformation mechanisms. Rapid developments have occurred in the studying rock microstructures due to recent improvements in analytical techniques such as Electron Backscatter Diffraction (EBSD). EBSD technique allows quick automated microtextural characteritzation. The deformed banded iron formations (BIFs) occurring in the Quadrilátero Ferrífero (QF) province in Brazil have been studied extensively with EBSD. All studies have focused mainly in CPOs. The general agreement is that dislocation creep was the dominant process of deformation, for the strong c-axis fabric of hematite crystals. This idea is substantiated by viscoplastic self-consistent models for deformation of hematite. However there are limitations to analyzing natural CPOs alone, or those generated by deformation models. The strong c-axis fabric could be taken as equally powerful an evidence for other known deformation mechanisms. Some grain boundary types in BIFs of the QF are irregular and comprise equant grains in granoblastic texture (Figure 1a). CPOs for this kind are strong and consistent with a predominance of dislocation creep. Others are very regular and long parallel to basal planes of hematites forming large elongated crystals (lepidoblastic texture, Figure 1b). Such crystals are called specularite, and their formation has been previously attributed to dislocation creep. This is erroneous because of the high strains which would be required. Their shape must be due to anisotropic grain growth. Other types lie between the above end-textures. Both types of grain shape microstructures have the same core deformation mechanism. Describing their genetic differences is crucial, since specularite owe its shape to anisotropic grain growth. It is not possible yet to confirm that dislocation creep was the

  12. Triboluminescence dominated by crystallographic orientation

    Science.gov (United States)

    Wang, Kuifang; Ma, Liran; Xu, Xuefeng; Wen, Shizhu; Luo, Jianbin

    2016-05-01

    Triboluminescence (TL) is an optical phenomenon that has a long and varied history with broad applications, such as damage detection, X-ray source, and mass health monitoring sensor. So far, the properties and mechanisms of TL remain not completely understood. The TL properties emitted during the sliding contact between Al2O3 and SiO2 surfaces were studied along different crystallographic orientations. In this study, the TL intensity of Al2O3 was significantly enhanced as Al2O3 surface was along a particular crystallographic orientation, which is an unconventional phenomenon. TL enhancement of Al2O3 was not affected by air atmosphere and atomic stocking mode of Al2O3. The enhancement mechanism of Al2O3 may be influenced by the surface state of Al2O3. This work provides a new method to control the intensity of TL and novel ideas to elucidate the TL mechanism.

  13. Rheology, microstructure and crystallographic preferred orientation of matrix containing a dispersed second phase: Insight from experimentally deformed ice

    Science.gov (United States)

    Cyprych, Daria; Piazolo, Sandra; Wilson, Christopher J. L.; Luzin, Vladimir; Prior, David J.

    2016-09-01

    We utilize in situ neutron diffraction to continuously track the average grain size and crystal preferred orientation (CPO) development in ice, during uniaxial compression of two-phase and pure ice samples. Two-phase samples are composed of ice matrix and 20 vol.% of second phases of two types: (1) rheologically soft, platy graphite, and (2) rigid, rhomb-shaped calcite. The samples were tested at 10 °C below the ice melting point, ambient pressures, and two strain rates (1 ×10-5 and 2.5 ×10-6 s-1), to 10 and 20% strain. The final CPO in the ice matrix, where second phases are present, is significantly weaker, and ice grain size is smaller than in an ice-only sample. The microstructural and rheological data point to dislocation creep as the dominant deformation regime. The evolution and final strength of the CPO in ice depend on the efficiency of the recrystallization processes, namely grain boundary migration and nucleation. These processes are markedly influenced by the strength, shape, and grain size of the second phase. In addition, CPO development in ice is further accentuated by strain partitioning into the soft second phase, and the transfer of stress onto the rigid second phase.

  14. Crystallographic orientation dependent etching of graphene layers

    Energy Technology Data Exchange (ETDEWEB)

    Nemes-Incze, Peter; Biro, Laszlo Peter [Research Institute for Technical Physics and Materials Science, PO. Box 49, 1525 Budapest (Hungary); Magda, Gabor [Budapest University of Technology and Economics (BME), PO Box 91, 1521 Budapest (Hungary); Kamaras, Katalin [Research Institute for Solid State Physics and Optics, Hungarian Academy of Sciences, PO Box 49, 1525, Budapest (Hungary)

    2010-04-15

    Graphene has gripped the scientific community ever since its discovery in 2004, with very promising electronic properties and hopes to integrate graphene into nanoelectronic devices. For graphene to make its way into electronic devices, two major obstacles have to be overcome: reproducible preparation of large area graphene samples and patterning techniques to obtain functional components. In this paper we present a graphene etching technique, which is crystallographic orientation selective and allows for the patterning of graphene layers using a chemical reduction process. The process involves the reduction of the SiO{sub 2} support by the carbon in the graphene itself. This reaction only occurs at the sample edges and does not result in the degradation of the graphene crystal lattice itself. However, we have observed evidence of strong hole doping in our etched samples. This etching technique opens up new possibilities in graphene patterning and modification. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  15. Crystallographic orientation and concentric layers in spicules of calcareous sponges.

    Science.gov (United States)

    Rossi, André Linhares; Ribeiro, Bárbara; Lemos, Moara; Werckmann, Jacques; Borojevic, Radovan; Fromont, Jane; Klautau, Michelle; Farina, Marcos

    2016-11-01

    In this work, the crystallography of calcareous sponges (Porifera) spicules and the organization pattern of the concentric layers present in their inner structure were investigated in 10 species of the subclass Calcaronea and three species of the subclass Calcinea. Polished spicules had specific concentric patterns that varied depending on the plane in which the spicules were sectioned. A 3D model of the concentric layers was created to interpret these patterns and the biomineralization process of the triactine spicules. The morphology of the spicules was compared with the crystallographic orientation of the calcite crystals by analyzing the Kikuchi diffraction patterns using a scanning electron microscope. Triactine spicules from the subclass Calcinea had actines (rays) elongated in the 〈210〉 direction, which is perpendicular to the c-axis. The scale spicules of the hypercalcified species Murrayona phanolepis presented the c-axis perpendicular to the plane of the scale, which is in accordance with the crystallography of all other Calcinea. The triactine spicules of the calcaronean species had approximately the same crystallographic orientation with the unpaired actine elongated in the ∼[211] direction. Only one Calcaronea species, whose triactine was regular, had a different orientation. Three different crystallographic orientations were found in diactines. Spicules with different morphologies, dimensions and positions in the sponge body had similar crystallographic directions suggesting that the crystallographic orientation of spicules in calcareous sponges is conserved through evolution. Copyright © 2016 Elsevier Inc. All rights reserved.

  16. Shape and crystallographic orientation of nanodiamonds for quantum sensing.

    Science.gov (United States)

    Ong, S Y; Chipaux, M; Nagl, A; Schirhagl, R

    2017-01-23

    Nanodiamonds with dimensions down to a few tens of nanometers containing nitrogen-vacancy (NV) color centers have revealed their potential as powerful and versatile quantum sensors with a unique combination of spatial resolution and sensitivity. The NV centers allow transducing physical properties, such as strain, temperature, and electric or magnetic field, to an optical transition that can be detected in the single photon range. For example, this makes it possible to sense a single electron spin or a few nuclear spins by detecting their magnetic resonance. The location and orientation of these defects with respect to the diamond surface play a crucial role in interpreting the data and predicting their sensitivities. Despite its relevance, the geometry of these nanodiamonds has never been thoroughly investigated. Without accurate data, spherical models have been applied to interpret or predict results in the past. With the use of High Resolution Transmission Electron Microscopy (HR-TEM), Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM), we investigated nanodiamonds with an average hydrodynamic diameter of 25 nm (the most common type for quantum sensing) and found a flake-like geometry, with 23.2 nm and 4.5 nm being the average lateral and vertical dimensions. We have also found evidence for a preferred crystallographic orientation of the main facet in the (110) direction. Furthermore, we discuss the consequences of this difference in geometry on diamond-based applications. Shape not only influences the creation efficiency of nitrogen-vacancy centers and their quantum coherence properties (and thus sensing performance), but also the optical properties of the nanodiamonds, their interaction with living cells, and their surface chemistry.

  17. Crystallographic Orientation Effect on Electromigration in Ni-Sn Microbump

    Science.gov (United States)

    Huang, Yi-Ting; Chen, Chih-Hao; Chakroborty, Subhendu; Wu, Albert T.

    2017-09-01

    This article addresses the reliability challenges regarding electromigration in developing three-dimensional integrated circuits (3D-ICs). The line-type sandwich structure of Ni/Sn3.5Ag(15 μm)/Ni was used to simulate microbumps to examine the reliability of electromigration in 3D-IC technology. The solder strip of Ni/Sn3.5Ag(15 μm)/Ni was stressed with a current density of 1.0 × 104 A/cm2 at 150°C. The current stressing enhanced the reaction between the solder and Ni to form Ni3Sn4, which occupied the entire joint and transformed into a Ni/Ni3Sn4/Ni structure when the solder was completely consumed. Electron backscatter diffraction was used to analyze the crystallographic characteristics of Sn and Ni3Sn4 as related to the electromigration effect. The results indicated that the crystallographic orientation of Sn plays a significant role in the Ni/Sn3.5Ag/Ni, whereas the orientation of Ni3Sn4 is the dominant factor of diffusion behavior in the Ni/Ni3Sn4/Ni.

  18. Crystallographic Orientation Effect on Electromigration in Ni-Sn Microbump

    Science.gov (United States)

    Huang, Yi-Ting; Chen, Chih-Hao; Chakroborty, Subhendu; Wu, Albert T.

    2017-07-01

    This article addresses the reliability challenges regarding electromigration in developing three-dimensional integrated circuits (3D-ICs). The line-type sandwich structure of Ni/Sn3.5Ag(15 μm)/Ni was used to simulate microbumps to examine the reliability of electromigration in 3D-IC technology. The solder strip of Ni/Sn3.5Ag(15 μm)/Ni was stressed with a current density of 1.0 × 104 A/cm2 at 150°C. The current stressing enhanced the reaction between the solder and Ni to form Ni3Sn4, which occupied the entire joint and transformed into a Ni/Ni3Sn4/Ni structure when the solder was completely consumed. Electron backscatter diffraction was used to analyze the crystallographic characteristics of Sn and Ni3Sn4 as related to the electromigration effect. The results indicated that the crystallographic orientation of Sn plays a significant role in the Ni/Sn3.5Ag/Ni, whereas the orientation of Ni3Sn4 is the dominant factor of diffusion behavior in the Ni/Ni3Sn4/Ni.

  19. 3D characterization of crystallographic orientation in polycrystals via EBSD

    Institute of Scientific and Technical Information of China (English)

    Stefan ZAEFFERER; Stuart I. WRIGHT

    2007-01-01

    Electron Backscatter Diffraction (EBSD) has been used in conjunction with a Scanning Electron Microscope (SEM) combined with a focused ion beam (FIB) instrument to obtain three dimensional (3D) high resolution characterizations of crystalline microstructures. This work reports on continued development that has proceeded on this technique. The technique is based on automated in-situ serial sectioning using the FIB and characterization of the sections using automated EBSD or orientation imaging microscopy (OIM). The technique extends the powerful features of two dimensional OIM into the third spatial dimension. This allows additional descriptive microstructural parameters to be obtained, for example the morphology and the crystallographic indices of interface planes. This paper provides an overview of the technique and shows results from two different samples: pearlite colonies in a high carbon steel and twin related grain triplets in a NiCo thin film.

  20. The orientational preferences of backbones of proteins

    Institute of Scientific and Technical Information of China (English)

    CHEN Ying; WANG Jun; XUE Bin; WANG Wei

    2006-01-01

    The orientation between the backboneresidues of proteins is defined based on the local configurations and the corresponding preferences are analyzed by statistics. It is found that all the residue pairs have some specific preferences of orientations. The statistical analysis is mainly concentrated in the orientational distributions for two kinds of groupings of residues based on the hydrophobicity and secondary structural features. The statistics for such two types of groupings shows different orientational preferences. It is found that for the former grouping the orientational preference is rather weak,while for the later a kind of strong orientational preferences. This suggests that the formation of local structures and of secondary structures are highly related to the orientational preferences.

  1. Crystallographic Orientation of Cuttlebone Shield Determined by Electron Backscatter Diffraction

    Science.gov (United States)

    Cusack, Maggie; Chung, Peter

    2014-01-01

    In common with many cephalopod mollusks, cuttlefish produce an internal biomineral buoyancy device. This cuttlebone is analogous to a surf board in shape and structure, providing rigidity and a means of controlling buoyancy. The cuttlebone is composed of calcium carbonate in the form of aragonite and comprises an upper dorsal shield and a lower lamellar matrix. The lamellar matrix comprises layers of chambers with highly corrugated walls. The dorsal shield comprises bundles of aragonite needles stacked on top of each other. Electron backscatter diffraction analyses of the dorsal shield reveal that the c-axis of aragonite is parallel with the long axis of the needles in the bundles such that any spread in crystallographic orientation is consistent with the spread in orientation of the fibers as they radiate to form the overall structure of the dorsal shield. This arrangement of c-axis coincident with the long axis of the biomineral structure is similar to the arrangement in corals and in contrast to the situation in the molluskan aragonite nacre of brachiopod calcite where the c-axis is perpendicular to the aragonite tablet or calcite fiber, respectively.

  2. Variations in Reactivity on Different Crystallographic Orientations of Cerium Oxide

    Energy Technology Data Exchange (ETDEWEB)

    Mullins, David R [ORNL; Albrecht, Peter M [ORNL; Calaza, Florencia C [ORNL

    2013-01-01

    Cerium oxide is a principal component in many heterogeneous catalytic processes. One of its key characteristics is the ability to provide or remove oxygen in chemical reactions. The different crystallographic faces of ceria present significantly different surface structures and compositions that may alter the catalytic reactivity. The structure and composition determine the number of coordination vacancies surrounding surface atoms, the availability of adsorption sites, the spacing between adsorption sites and the ability to remove O from the surface. To investigate the role of surface orientation on reactivity, CeO2 films were grown with two different orientations. CeO2(100) films were grown ex situ by pulsed laser deposition on Nb-doped SrTiO3(100). CeO2(111) films were grown in situ by thermal deposition of Ce metal onto Ru(0001) in an oxygen atmosphere. The chemical reactivity was characterized by the adsorption and decomposition of various molecules such as alcohols, aldehydes and organic acids. In general the CeO2(100) surface was found to be more active, i.e. molecules adsorbed more readily and reacted to form new products, especially on a fully oxidized substrate. However the CeO2(100) surface was less selective with a greater propensity to produce CO, CO2 and water as products. The differences in chemical reactivity are discussed in light of possible structural terminations of the two surfaces. Recently nanocubes and nano-octahedra have been synthesized that display CeO2(100) and CeO2(111) faces, respectively. These nanoparticles enable us to correlate reactions on high surface area model catalysts at atmospheric pressure with model single crystal films in a UHV environment.

  3. Synthesis of crystallographically oriented olivine aggregates using colloidal processing in a strong magnetic field

    Science.gov (United States)

    Koizumi, Sanae; Suzuki, Tohru S.; Sakka, Yoshio; Yabe, Kosuke; Hiraga, Takehiko

    2016-11-01

    This study develops a fabrication technique to obtain Fe-free and Fe-bearing (Fe:Mg = 1:9) olivine aggregates not only with high density and fine grain size but with crystallographic preferred orientation (CPO). A magnetic field (≤12 T) is applied to synthetic, fine-grained ( 120 nm), olivine particles dispersed in solvent. The alignment of certain crystallographic axes of the particles with respect to a magnetic direction is anticipated due to magnetic anisotropy of olivine. The dispersed particles are gradually consolidated on a porous alumina mold covered with a solid-liquid separation filter during drainage of the solvent. The resultant aligned consolidated aggregate is then isostatically pressed and vacuum sintered. We find that (1) preparation of fully reacted olivine particles, with less propensity to coalesce; (2) preparation of a suspension with highly dispersed particles; and (3) application of a certain strength of the magnetic field are essential to obtain well-sintered and well-aligned aggregates. High density (i.e., olivine aggregates were successfully synthesized with uniaxially aligned a- and c-axes, respectively. Attempts to uniaxially align the magnetization hard axis and to triaxially align Fe-bearing olivine by rotating the suspension in the magnetic field succeeded in obtaining weakly developed CPO aggregates.

  4. The Ultrasonic Measurement of Crystallographic Orientation for Imaging Anisotropic Components with 2d Arrays

    Science.gov (United States)

    Lane, C. J. L.; Dunhill, A. K.; Drinkwater, B. W.; Wilcox, P. D.

    2011-06-01

    Single crystal components are used widely in the gas-turbine industry. However, these components are elastically anisotropic which causes difficulties when performing NDE inspections with ultrasound. Recently an ultrasonic algorithm for a 2D array has been corrected to perform the reliable volumetric inspection of single crystals. For the algorithm to be implemented the crystallographic orientation of the components must be known. This paper, therefore, develops and reviews crystallographic orientation methods using 2D ultrasonic arrays. The methods under examination are based on the anisotropic propagation of surface and bulk waves and an image-based orientation method is also considered.

  5. Magnetic anisotropy induced by crystallographic orientation and morphological alignment in directionally-solidified eutectic Mn-Sb alloy

    Science.gov (United States)

    Lou, Chang-Sheng; Liu, Tie; Dong, Meng; Wu, Chun; Shao, Jian-Guo; Wang, Qiang

    2017-02-01

    The influences of the crystallographic orientation and morphological alignment upon the magnetic anisotropic behavior of polycrystalline materials were investigated. Microstructures obtained in eutectic Mn-Sb alloys via directional solidification simultaneously displayed crystallographic orientation and morphological alignment. Both the crystallographic orientation and the morphological alignment were able to induce magnetic anisotropy in the alloys, wherein the influence of the crystallographic orientation and the morphological alignment upon the magnetic anisotropic behavior of the alloys strongly depended upon their directions and exhibited either mutual promotion or competition. These findings may provide useful guidance for the fabrication design of functional magnetic materials.

  6. Experimental and Theoretical Investigation of Crystallographic Orientation Dependence of Nanoscratching of Single Crystalline Copper

    Science.gov (United States)

    Geng, Yanquan; Zhang, Junjie; Yan, Yongda; Yu, Bowen; Geng, Lin; Sun, Tao

    2015-01-01

    In the present work, we perform experiments and molecular dynamics simulations to elucidate the underlying deformation mechanisms of single crystalline copper under the load-controlled multi-passes nanoscratching using a triangular pyramidal probe. The correlation of microscopic deformation behavior of the material with macroscopically-observed machining results is revealed. Moreover, the influence of crystallographic orientation on the nanoscratching of single crystalline copper is examined. Our simulation results indicate that the plastic deformation of single crystalline Cu under the nanoscratching is exclusively governed by dislocation mechanisms. However, there is no glissile dislocation structure formed due to the probe oscillation under the load-controlled mode. Both experiments and MD simulations demonstrate that the machined surface morphologies in terms of groove depth and surface pile-up exhibit strong crystallographic orientation dependence, because of different geometries of activated slip planes cutting with free surfaces and strain hardening abilities associated with different crystallographic orientations. PMID:26147506

  7. Experimental and Theoretical Investigation of Crystallographic Orientation Dependence of Nanoscratching of Single Crystalline Copper.

    Directory of Open Access Journals (Sweden)

    Yanquan Geng

    Full Text Available In the present work, we perform experiments and molecular dynamics simulations to elucidate the underlying deformation mechanisms of single crystalline copper under the load-controlled multi-passes nanoscratching using a triangular pyramidal probe. The correlation of microscopic deformation behavior of the material with macroscopically-observed machining results is revealed. Moreover, the influence of crystallographic orientation on the nanoscratching of single crystalline copper is examined. Our simulation results indicate that the plastic deformation of single crystalline Cu under the nanoscratching is exclusively governed by dislocation mechanisms. However, there is no glissile dislocation structure formed due to the probe oscillation under the load-controlled mode. Both experiments and MD simulations demonstrate that the machined surface morphologies in terms of groove depth and surface pile-up exhibit strong crystallographic orientation dependence, because of different geometries of activated slip planes cutting with free surfaces and strain hardening abilities associated with different crystallographic orientations.

  8. Transfer of olivine crystallographic orientation through a cycle of serpentinisation and dehydration

    Science.gov (United States)

    Dunkel, Kristina G.; Austrheim, Håkon; Ildefonse, Benoit; Jamtveit, Bjørn

    2017-08-01

    Our ability to decipher the mechanisms behind metamorphic transformation processes depends in a major way on the extent to which crystallographic and microstructural information is transferred from one stage to another. Within the Leka Ophiolite Complex in the Central Norwegian Caledonides, prograde olivine veins that formed by dehydration of serpentinite veins in dunites exhibit a characteristic distribution of microstructures: The outer part of the veins comprises coarse-grained olivine that forms an unusual, brick-like microstructure. The inner part of the veins, surrounding a central fault, is composed of fine-grained olivine. Where the fault movement included a dilational component, optically clear, equant olivine occurs in the centre. Electron backscatter diffraction mapping reveals that the vein olivine has inherited its crystallographic preferred orientation (CPO) from the olivine in the porphyroclastic host rock; however, misorientation is weaker and associated to different rotation axes. We propose that prograde olivine grew epitaxially on relics of mantle olivine and thereby acquired its CPO. Growth towards pre-existing microfractures along which serpentinisation had occurred led to straight grain boundaries and a brick-like microstructure in the veins. When dehydration embrittlement induced slip, a strong strain localisation on discrete fault planes prevented distortion of the CPO due to cataclastic deformation; grain size reduction did not significantly modify the olivine CPO. This illustrates how a CPO can be preserved though an entire metamorphic cycle, including hydration, dehydration, and deformation processes, and that the CPO and the microstructures (e.g. grain shape) of one phase do not necessarily record the same event.

  9. The relation between microstructure and crystallographic orientation in rolled copper and brass

    DEFF Research Database (Denmark)

    Christoffersen, H.; Leffers, Torben

    2002-01-01

    The relation between microstructure and crystallographic orientation is investigated in rolled copper and brass. For the two main types of microstructure in copper (the high wall density and the low wall density structure) there is a certain relation: theorientations corresponding to a specific...... type tend to cluster in certain regions of orientation space. However, the clustering is not very pronounced (there is a lot of overlap), and it cannot be related to any model. There is also a certain grain-sizeeffect: the average grain with high wall density structure is larger than the average grain...... with low wall density structure. For a third type of microstructure (to be described) there is a very clear relation to the crystallographic orientation. For brassthe distinction is between grains with and grains without deformation twins. There is a clear trend for the grains with twins to cluster...

  10. Determination of crystallographic and macroscopic orientation of planar structures in TEM

    DEFF Research Database (Denmark)

    Huang, X.; Liu, Q.

    1998-01-01

    With the aid of a double-tilt holder in a transmission electron microscope (TEM), simple methods are described for determination of the crystallographic orientation of a planar structure and for calculation of the macroscopic orientation of the planar structure. The correlation between a planar s...... taken at tilted positions, can be transformed to the real macroscopic orientation of the planar structures with estimated error of about +/- 2 degrees. (C) 1998 Elsevier Science B.V. All rights reserved....... structure and a crystallographic plane can be found by comparing the differences in their trace directions on the projection plane and inclination angles with respect to that plane. The angles between the traces of planar structures and the sample axis measured from the TEM micrographs, which have been...

  11. Crystallographic orientation and induced potential effects in photoelectron emission from metal surfaces by ultrashort laser pulses

    CERN Document Server

    Rubiano, C A Rios; Mitnik, D M; Silkin, V M; Gravielle, M S

    2016-01-01

    The influence of the crystallographic orientation of a typical metal surface, like aluminum, on electron emission spectra produced by grazing incidence of ultrashort laser pulses is investigated by using the band-structure-based-Volkov (BSB-V) approximation. The present version of the BSB-V approach includes not only a realistic description of the surface interaction, accounting for band structure effects, but also effects due to the induced potential that originates from the collective response of valence-band electrons to the external electromagnetic field. The model is applied to evaluate differential electron emission probabilities from the valence band of Al(100) and Al(111). For both crystallographic orientations, the contribution of partially occupied surface electronic states and the influence of the induced potential are separately analyzed as a function of the laser carrier frequency. We found that the induced potential strongly affects photoelectron emission distributions, opening a window to scrut...

  12. Crystallographic orientation-dependent pattern replication in direct imprint of aluminum nanostructures

    OpenAIRE

    2015-01-01

    In the present work, we perform molecular dynamics simulations corroborated by experimental validations to elucidate the underlying deformation mechanisms of single-crystalline aluminum under direct imprint using a rigid silicon master. We investigate the influence of crystallographic orientation on the microscopic deformation behavior of the substrate materials and its correlation with the macroscopic pattern replications. Furthermore, the surface mechanical properties of the patterned struc...

  13. Experimental and Theoretical Investigation of Crystallographic Orientation Dependence of Nanoscratching of Single Crystalline Copper

    OpenAIRE

    2015-01-01

    In the present work, we perform experiments and molecular dynamics simulations to elucidate the underlying deformation mechanisms of single crystalline copper under the load-controlled multi-passes nanoscratching using a triangular pyramidal probe. The correlation of microscopic deformation behavior of the material with macroscopically-observed machining results is revealed. Moreover, the influence of crystallographic orientation on the nanoscratching of single crystalline copper is examined....

  14. Ge/SrTiO{sub 3}(001): Correlation between interface chemistry and crystallographic orientation

    Energy Technology Data Exchange (ETDEWEB)

    Gobaut, B.; Penuelas, J.; Grenet, G.; Ferrah, D.; Benamrouche, A.; Chettaoui, A.; Robach, Y.; Botella, C.; Saint-Girons, G. [Universite de Lyon, Institut des Nanotechnologies de Lyon, Ecole Centrale de Lyon, 36 avenue Guy de Collongue, 69134 Ecully (France); El Kazzi, M.; Silly, M. G.; Sirotti, F. [Synchrotron SOLEIL (TEMPO beamline), l' Orme des Merisiers, Saint-Aubin, 91192 Gif-sur-Yvette (France)

    2012-11-01

    In this work, the desorption of a submonolayer deposit of Ge on SrTiO{sub 3}(001) is studied by reflection high energy electron diffraction. The results are compared to those of a previous experiment done using soft x-ray photoelectron spectroscopy. Combining these techniques allows for correlating interface chemistry and crystal orientation, and for bringing clarifying elements concerning the competition between (111) and (001) crystal orientation typical for the semiconductor/perovskite epitaxial systems. Despite poor interface matching, (111)-oriented islands are stabilized at the expense of (001)-oriented islands due to the relatively low energy of their free facets. Such 'surface energy driven' crystallographic orientation of the deposit is enhanced by the low adhesion energy characteristic of the Ge/SrTiO{sub 3} system.

  15. Crystal preferred orientation in peridotite ultramylonites deformed by grain size sensitive creep, étang de Lers, Pyrenees, France

    NARCIS (Netherlands)

    Drury, M.R.; Avé Lallemant, H.G.; Pennock, G.M.; Palasse, L.N.

    2011-01-01

    In naturally deformed upper mantle rocks a strong olivine crystallographic preferred orientation (CPO) occurs in rocks with grain sizes larger than about 15 mm. Finer grained peridotites tend to have weak to random olivine CPO. The different types of olivine CPO are usually interpreted in relation t

  16. Effect of crystallographic orientation on hillock formation in thermally cycled large grain tin films

    Science.gov (United States)

    Koppes, John Patrick

    Tin whiskers and hillocks grow spontaneously from the surfaces of polycrystalline Sn films at room temperature. Whiskers can grow long enough to cause short circuits in electronic devices. We hypothesized that the anisotropies of the crystal structure lead to locally high strain energies that are relieved by the growth of whiskers and hillocks. This research studies hillock formations on large grain Sn-alloy films relative to the crystallographic orientations of the adjacent grains. Large grain films were produced by solidifying 96.5wt% Sn - 3wt% Ag - 0.5wt% Cu solder alloy on a Cu substrate. These surface defects (hillocks) grew predominately at grain boundaries during thermal cycling. The formation of the surface defects between two grains created a pseudo-bi-crystal sample geometry, making it ideal for studying surface defects relative to the local crystallographic orientations and the grains' corresponding anisotropic properties. The crystallographic orientations of the grains were studied with Electron Backscatter Diffraction (EBSD) and Laue micro-diffraction at the Lawrence Berkeley National Laboratory Advanced Light Source. Local orientation studies of the surface defects and the surrounding grains indicated that the surface defects nucleated and grew with low dislocation densities. In addition, the linear surface defect densities along the grain boundaries were measured and observed to change as a function of orientation. The change in linear defect density with respect to orientation was due, in part, to the anisotropy of the coefficient of thermal expansion of β-Sn. In addition, it was important to account for elastic anisotropies. The elastic stresses, strains, and strain energy densities of the microstructures were determined with Object Oriented Finite element analysis. The simulations indicated that during thermal cycling the local stresses exceeded the yield strength. As a result, the highest linear defect densities did not occur at orientations

  17. Preferred Orientation in Nanocomposite Permanent Magnet Materials

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Melt-spun (Nd11.4Fe82.9B5.7)0.99M1 ribbons (M=Zr, Nb, Ga, Zr+Ga, Nb+Ga) were prepared by melt-spinning technique. Ga addition is found to be effective for the orientation of c-axis of Nd2Fe14B grains perpendicular to the ribbon plane. Better magnetic properties can be achieved by adding both the two kinds of elements Zr+Ga, Nb+Ga, and it is found that the preferred orientation is further improved. The alignment degree changes with ribbon thickness and is highest when ribbon thickness is 120 μm. Heat treatment can improve the texture degree, but lead to coarser grains. Cryogenic treatment is first applied for the treatment of nanocomposite Nd2Fe14B/α-Fe melt-spun ribbons. The effects on magnetic properties and texture degree of nanocomposite magnets after cryogenic treatment were studied. The result shows that cryogenic treatment is beneficial to the enhancement of texture degree of melt-spun ribbon and the grain size has no obvious change.

  18. Preferred orientation in experimentally deformed stishovite: implications for deformation mechanisms

    Science.gov (United States)

    Kaercher, P. M.; Zepeda-Alarcon, E.; Prakapenka, V.; Kanitpanyacharoen, W.; Smith, J.; Sinogeikin, S. V.; Wenk, H. R.

    2014-12-01

    The crystal structure of the high pressure SiO2 polymorph stishovite has been studied in detail, yet little is known about its deformation mechanisms. Information about how stishovite deforms under stress is important for understanding subduction of quartz-bearing crustal rocks into the mantle. Particularly, stishovite is elastically anisotropic and thus development of crystallographic preferred orientation (CPO) during deformation may contribute to seismic anomalies in the mantle. We converted a natural sample of flint to stishovite in a laser heated diamond anvil cell and compressed the stishovite aggregate up to 38 GPa. Diffraction patterns were collected in situ in radial geometry at the Advanced Light Source (ALS) and the Advanced Photon Source (APS) to examine development of CPO during deformation. We find that (001) poles preferentially align with the compression direction and infer deformation mechanisms leading to the observed CPO with visco-plastic self consistent (VPSC) polycrystal plasticity models. Our results show pyramidal and basal slip are most likely active at high pressure and ambient temperature, in agreement with transmission electron microscopy (TEM) studies of rutile (TiO2) and paratellurite (TeO2), which are isostructural to stishovite. Conversely other TEM studies of stishovite done at higher temperature suggest dominant prismatic slip. This indicates that a variety of slip systems may be active in stishovite, depending on conditions. As a result, stishovite's contribution to the seismic signature in the mantle may vary as a function of pressure and temperature and thus depth.

  19. Enhancing nanoscale SEM image segmentation and reconstruction with crystallographic orientation data and machine learning

    Energy Technology Data Exchange (ETDEWEB)

    Converse, Matthew I., E-mail: mconverse85@yahoo.com; Fullwood, David T.

    2013-09-15

    Current methods of image segmentation and reconstructions from scanning electron micrographs can be inadequate for resolving nanoscale gaps in composite materials (1–20 nm). Such information is critical to both accurate material characterizations and models of piezoresistive response. The current work proposes the use of crystallographic orientation data and machine learning for enhancing this process. It is first shown how a machine learning algorithm can be used to predict the connectivity of nanoscale grains in a Nickel nanostrand/epoxy composite. This results in 71.9% accuracy for a 2D algorithm and 62.4% accuracy in 3D. Finally, it is demonstrated how these algorithms can be used to predict the location of gaps between distinct nanostrands — gaps which would otherwise not be detected with the sole use of a scanning electron microscope. - Highlights: • A method is proposed for enhancing the segmentation/reconstruction of SEM images. • 3D crystallographic orientation data from a nickel nanocomposite is collected. • A machine learning algorithm is used to detect trends in adjacent grains. • This algorithm is then applied to predict likely regions of nanoscale gaps. • These gaps would otherwise be unresolved with the sole use of an SEM.

  20. Influence of preferred orientation of minerals in the mineralogical identification process by X-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Amanda Luzia da; Oliveira, Arno H. de [Universidade Federal de Minas Gerais (DEN/UFMG), Belo Horizonte, MG (Brazil). Dept. de Engenharia Nuclear; Fernandes, Maria Lourdes Souza, E-mail: lourdesfernandes@ufmg.b [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Inst. de GeoCiencias. Centro de Pesquisa Professor Manoel Teixeira da Costa

    2011-07-01

    The X-ray diffraction corresponds to one of the main techniques for characterization of microstructures in crystalline materials, widely used in the identification of minerals in samples of geological materials. Some minerals have a property called preferred orientation which corresponds to the orientation tendency of the crystals of ground minerals to orient themselves in certain directions according to a preferred crystallographic plane. This property affects the analysis by X-ray diffraction and this fact can generates erroneous results in the characterization. The purpose of this study is to identify the negative influence of the preferred orientation of a mineral in the generation of diffraction patterns obtained in the X-ray diffraction analysis. For this, a sample of muscovite, a mineral of mica group, was prepared by two different methods: the frontal method and the back loading method. In the analysis using the frontal method there was displacement of the XRD pattern in the abscissa axis, where it was observed changes in interplanar distance and angle 2{theta} values, which are essential information for characterization and identification of a mineral. In the analysis using the back loading method, the generated XRD pattern showed no displacement in the axis of abscissas and showed interplanar distance and angle 2{theta} values closer to the real values for the muscovite. The results showed that one can only make improvements to the process of sample preparation minimizing the effect of preferred orientation in the analysis. There is no need to change conditions of diffractometer measurements. (author)

  1. Quantification of thin film crystallographic orientation using X-ray diffraction with an area detector.

    Science.gov (United States)

    Baker, Jessy L; Jimison, Leslie H; Mannsfeld, Stefan; Volkman, Steven; Yin, Shong; Subramanian, Vivek; Salleo, Alberto; Alivisatos, A Paul; Toney, Michael F

    2010-06-01

    As thin films become increasingly popular (for solar cells, LEDs, microelectronics, batteries), quantitative morphological and crystallographic information is needed to predict and optimize the film's electrical, optical, and mechanical properties. This quantification can be obtained quickly and easily with X-ray diffraction using an area detector in two sample geometries. In this paper, we describe a methodology for constructing complete pole figures for thin films with fiber texture (isotropic in-plane orientation). We demonstrate this technique on semicrystalline polymer films, self-assembled nanoparticle semiconductor films, and randomly packed metallic nanoparticle films. This method can be immediately implemented to help understand the relationship between film processing and microstructure, enabling the development of better and less expensive electronic and optoelectronic devices.

  2. Preferred orientation of ettringite in concrete fractures

    KAUST Repository

    Wenk, Hans-Rudolf

    2009-05-15

    Sulfate attack and the accompanying crystallization of fibrous ettringite [Ca6Al2(OH)12(SO4) 3·26H2O] cause cracking and loss of strength in concrete structures. Hard synchrotron X-ray microdiffraction is used to quantify the orientation distribution of ettringite crystals. Diffraction images are analyzed using the Rietveld method to obtain information on textures. The analysis reveals that the c axes of the trigonal crystallites are preferentially oriented perpendicular to the fracture surfaces. By averaging single-crystal elastic properties over the orientation distribution, it is possible to estimate the elastic anisotropy of ettringite aggregates. © 2009 International Union of Crystallography.

  3. The fcc-bcc crystallographic orientation relationship in AlxCoCrFeNi high-entropy alloys

    NARCIS (Netherlands)

    Rao, J. C.; Ocelik, V.; Vainchtein, D.; Tang, Z.; Liaw, P. K.; De Hosson, J. Th. M.

    2016-01-01

    This paper concentrates on the crystallographic-orientation relationship between the various phases in the Al-Co-Cr-Fe-Ni high-entropy alloys. Two types of orientation relationships of bcc phases (some with ordered B2 structures) and fcc matrix were observed in Al0.5CoCrFeNi and Al0.7CoCrFeNi alloys

  4. Preferred orientation of ettringite in concrete fractures

    Energy Technology Data Exchange (ETDEWEB)

    Wenk, Hans-Rudolf; Monteiro, Paulo J.M.; Kunz, Martin; Chen, Kai; Tamura, Nobumichi; Lutterotti, Luca; Delacroz, John

    2009-01-31

    Sulfate attack and the accompanying crystallization of fibrous ettringite [Ca{sub 6}Al{sub 2}(OH){sub 12}(SO{sub 4}){sub 3} {center_dot} 26H{sub 2}O] cause cracking and loss of strength in concrete structures. Hard synchrotron X-ray microdiffraction is used to quantify the orientation distribution of ettringite crystals. Diffraction images are analyzed using the Rietveld method to obtain information on textures. The analysis reveals that the c axes of the trigonal crystallites are preferentially oriented perpendicular to the fracture surfaces. By averaging single-crystal elastic properties over the orientation distribution, it is possible to estimate the elastic anisotropy of ettringite aggregates.

  5. Crystallographically Oriented Cobalt Chromium Tantalum Thin-Film Media for High Areal Density Recording.

    Science.gov (United States)

    Deng, Youping

    In order to develop the techniques for increasing recording areal density, microstructural, magnetic and recording properties of crystallographically-oriented CoCrTa thin-films were investigated. The oriented films included bi-crystal and quad-crystal CoCrTa thin films, which were prepared by sputtering on (100) and (110) single crystal Cr substrates, respectively. A theoretical model was developed to calculate the in-plane torque curves of the oriented films. Based on this model, experimental investigations were conducted on the quad-crystal CoCrTa films. It was found that, by fitting the measured in-plane torque curves of the quad -crystal CoCrTa film, it was possible to determine the magnetocrystalline anisotropy constants (K_{rm u1 } and K_{rm u2}) of the CoCrTa film. The torque curves of quad -crystal films were also found to be indicative of the grain isolation and could be used to optimize the sputtering conditions. Substrate bias changed the film composition and lowered M_{rm s} and K_{rm u1}, while improving grain isolation. A more realistic micromagnetic model, which used the measured values of M_ {rm s} and K_{ rm u1} and took the film's grain-cluster microstructure into account, was developed for the bi-crystal films. The simulation results fitted well with the experimental data. A low-speed contact-recording spin-stand, which utilized a magnetoresistive head, was set up for recording studies on the oriented thin-film media and an isotropic thin-film medium prepared on a NiP/Al substrate. The readback signal from the MR head appeared to have some correlation with the medium anisotropy. The recorded patterns were imaged by magnetic force microscopy. It was found that erased bands formed on the quad-crystal and isotropic thin -film media. On the bi-crystal thin-film media, however, clear erased bands were not observed possibly due to the large head-disk distance.

  6. Crystallographic analysis of rock grain orientation at meso- and microscale levels

    Energy Technology Data Exchange (ETDEWEB)

    Kulkov, A. S., E-mail: 727@sibmail.com; Kulkov, S. N., E-mail: kulkov@ms.tsc.ru [National Research Tomsk State University, Tomsk, 634050, Russia and Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Chernishov, A. I., E-mail: aich@ggf.tsu.ru; Tishin, P. A., E-mail: tishin-pa@mail.ru [National Research Tomsk State University, Tomsk, 634050 (Russian Federation); Lychagin, D. V., E-mail: dvl-tomsk@mail.ru [National Research Tomsk State University, Tomsk, 634050, Russia and National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation)

    2014-11-14

    This paper studies the results of electron backscatter diffraction analysis of naturally deformed polycrystalline olivine. It also defines the dependence of lattice-preferred orientations of grains on their microstructural position and size. The authors detect the basic mechanisms, consequence and thermal dynamic modes of deformation. They also show that the development of a polycrystalline structure is determined by the following consecutive activation of sliding systems (010)[100] → (0kl)[100] → (100)[010] → (100)[001] → (110)[001], when dislocation sliding and diffusion creep change under the temperature decrease from 1000°C to 650°C.

  7. The preferences of orientations between the Pairs of amino acids

    Institute of Scientific and Technical Information of China (English)

    Chen Ying; Wang Jun; Wang Wei

    2007-01-01

    In this work,we make an investigation on the preferences of orientations between amino acids using the orientation defined based on the local geometry of the amino acids concerned.It is found that there are common preferences of orientations (70°,30°,140°) and (110°,340°,100°) for various pairs of amino acids.Different side chains may strengthen or weaken the common preferences,which is related to the effect of packing.Some amino acids having specific local flexibility may possess some preferences of orientations besides the common ones,such as (10°,280°,210°) .Another analysis on the pairs of the amino acids with different secondary-structure preferences shows that the directional interaction may affect the distribution of orientation more effectively than the packing or local flexibility.All these results provide us some insight of the organization of amino acids in protein,and their relation with some related interactions.

  8. On the condensation and preferred orientation of TiC nanocrystals - effects of electric field, substrate temperature and second phase

    Energy Technology Data Exchange (ETDEWEB)

    Kuo, L.-Y.; Shen, P. [National Sun Yat-Sen Univ., Kaohsiung (Taiwan). Inst. of Mater. Sci. and Eng.

    2000-01-15

    The condensates formed by reacting Ti plasma with C{sub 2}H{sub 2} gas (75 sccm) under relatively low vacuum (1 x 10{sup -3} Torr) and collected on carbon-coated collodion film were characterized by transmission electron microscopy to be TiC nanocrystals in random crystallographic orientation. The TiC condensates showed preferred orientation (200) when assembled on polycrystalline and amorphous substrates at ca. 150 C, and changed further into (111) when the substrate was subject to voltage bias (-120 V) with or without preheating to 450 C. The {alpha}-Ti co-deposited, with the TiC at a relatively low flow rate of C{sub 2}H{sub 2} (25 sccm), followed the crystallographic relationship: (0001){sub {alpha}}{sub -Ti}//(111){sub TiC}; [11 anti 20]{sub {alpha}}{sub -Ti}//[1 anti 10]{sub TiC}, in accordance with the TiC (111) preferred orientation. On the other hand, the amorphous carbon formed at a high flow rate of C{sub 2}H{sub 2} (250 sccm) hindered the preferred orientation (111) of TiC. The effects of applied electric field, substrate temperature and second phase on the accumulation and reorientation of the TiC condensates in the coating can be rationalized by surface charge of the TiC crystallites, Brownian rotation-coalescence of the crystallites, and atom configuration specification at the interphase interface, respectively. (orig.)

  9. Glassy Carbon Electrode-Supported Au Nanoparticles for the Glucose Electrooxidation: On the Role of Crystallographic Orientation

    Directory of Open Access Journals (Sweden)

    M. Guerra-Balcázar

    2012-01-01

    Full Text Available Glucose electrooxidation in alkaline solution was examined using glassy carbon electrodes modified with Au nanoparticles. Au nanoparticles were prepared following the two-phase protocol and characterized by transmission electron microscopy (TEM, UV-Vis spectroscopy, X-ray diffraction spectroscopy (XRD, and cyclic voltammetry (CV. It was found that, under the study conditions, it is possible to obtain nanoparticles between 1 and 5 nm; also it was found that the crystallographic orientation is strongly influenced by the ratio metal/thiol and to a lesser extent by the synthesis temperature. The voltammetric response for the electrocatalytic oxidation of glucose at carbon Au nanoparticle-modified electrode shows an increasing activity with nanoparticles size. Electroactivity and possibly selectivity are found to be nanoparticles' crystallographic orientation dependent. Classical electrochemical analysis shows that glucose electrooxidation is a diffusion-controlled process followed by a homogenous reaction.

  10. Coupled Crystal Plasticity-Phase Field Fracture Simulation Study on Damage Evolution Around a Void: Pore Shape Versus Crystallographic Orientation

    Science.gov (United States)

    Diehl, Martin; Wicke, Marcel; Shanthraj, Pratheek; Roters, Franz; Brueckner-Foit, Angelika; Raabe, Dierk

    2017-03-01

    Various mechanisms such as anisotropic plastic flow, damage nucleation, and crack propagation govern the overall mechanical response of structural materials. Understanding how these mechanisms interact, i.e. if they amplify mutually or compete with each other, is an essential prerequisite for the design of improved alloys. This study shows—by using the free and open source software DAMASK (the Düsseldorf Advanced Material Simulation Kit)—how the coupling of crystal plasticity and phase field fracture methods can increase the understanding of the complex interplay between crystallographic orientation and the geometry of a void. To this end, crack initiation and propagation around an experimentally obtained pore with complex shape is investigated and compared to the situation of a simplified spherical void. Three different crystallographic orientations of the aluminum matrix hosting the defects are considered. It is shown that crack initiation and propagation depend in a non-trivial way on crystallographic orientation and its associated plastic behavior as well as on the shape of the pore.

  11. Gender identity rather than sexual orientation impacts on facial preferences.

    Science.gov (United States)

    Ciocca, Giacomo; Limoncin, Erika; Cellerino, Alessandro; Fisher, Alessandra D; Gravina, Giovanni Luca; Carosa, Eleonora; Mollaioli, Daniele; Valenzano, Dario R; Mennucci, Andrea; Bandini, Elisa; Di Stasi, Savino M; Maggi, Mario; Lenzi, Andrea; Jannini, Emmanuele A

    2014-10-01

    Differences in facial preferences between heterosexual men and women are well documented. It is still a matter of debate, however, how variations in sexual identity/sexual orientation may modify the facial preferences. This study aims to investigate the facial preferences of male-to-female (MtF) individuals with gender dysphoria (GD) and the influence of short-term/long-term relationships on facial preference, in comparison with healthy subjects. Eighteen untreated MtF subjects, 30 heterosexual males, 64 heterosexual females, and 42 homosexual males from university students/staff, at gay events, and in Gender Clinics were shown a composite male or female face. The sexual dimorphism of these pictures was stressed or reduced in a continuous fashion through an open-source morphing program with a sequence of 21 pictures of the same face warped from a feminized to a masculinized shape. An open-source morphing program (gtkmorph) based on the X-Morph algorithm. MtF GD subjects and heterosexual females showed the same pattern of preferences: a clear preference for less dimorphic (more feminized) faces for both short- and long-term relationships. Conversely, both heterosexual and homosexual men selected significantly much more dimorphic faces, showing a preference for hyperfeminized and hypermasculinized faces, respectively. These data show that the facial preferences of MtF GD individuals mirror those of the sex congruent with their gender identity. Conversely, heterosexual males trace the facial preferences of homosexual men, indicating that changes in sexual orientation do not substantially affect preference for the most attractive faces. © 2014 International Society for Sexual Medicine.

  12. strain partitioning and dimensional preferred orientation in a syn ...

    African Journals Online (AJOL)

    Administrator

    a non-hydrostatic stress state, dimensional preferred orientation and strain are partitioned ... attention paid to the relationship existing among the various lithology ... Macroscopic analysis: The most dominant intrusive rock type in the western ... Mesoscopic observations: At the level of the exposure and hand specimen, the ...

  13. Electrical properties of NiAs-type MnTe films with preferred crystallographic plane of (110)

    Energy Technology Data Exchange (ETDEWEB)

    Yang, L.; Wang, Z. H., E-mail: zhwang@imr.ac.cn; Zhang, Z. D. [Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences, 72 Wenhua Road, Shenyang 110016 (China)

    2016-01-28

    NiAs-type manganese telluride (MnTe) films with preferred crystallographic plane of (110) were prepared on Si/SiO{sub 2} substrates by pulsed laser deposition. X-ray diffraction (XRD) of the films was studied at different temperatures. The XRD peak of MnTe (110) films shifts to higher angle with decreasing temperature, showing the decrease of the lattice parameter. Resistivity of the films was studied in the temperature range of 2–350 K. The bump between 150 and 250 K was observed in the films, which may be related to the special s-d and p-d overlaps induced by the compressed lattice. The magnon drag effect near its Néel temperature T{sub N} and enlarged magnetic-elastic coupling below 100 K were observed and analyzed in details.

  14. Preferred orientation of n-hexane crystallized in silicon nanochannels: A combined x-ray diffraction and sorption isotherm study

    CERN Document Server

    Henschel, Anke; Hofmann, Tommy; Knorr, Klaus; Huber, Patrick; 10.1103/PhysRevE.79.032601

    2009-01-01

    We present an x-ray diffraction study on n-hexane in tubular silicon channels of approximately 10 nm diameter both as a function of the filling fraction f of the channels and as a function of temperature. Upon cooling, confined n-hexane crystallizes in a triclinic phase typical of the bulk crystalline state. However, the anisotropic spatial confinement leads to a preferred orientation of the confined crystallites, where the crystallographic direction coincides with the long axis of the channels. The magnitude of this preferred orientation increases with the filling fraction, which corroborates the assumption of a Bridgman-type crystallization process being responsible for the peculiar crystalline texture. This growth process predicts for a channel-like confinement an alignment of the fastest crystallization direction parallel to the long channel axis. It is expected to be increasingly effective with the length of solidifying liquid parcels and thus with increasing f. In fact, the fastest solidification front...

  15. Perceptual Orientation for Housing Interior Walls Finishes Choice and Preference

    Directory of Open Access Journals (Sweden)

    Dr. ZINAS, Bako Zachariah

    2015-02-01

    Full Text Available Housing interior walls are decorated and finished with various decorative materials of paints of varying properties ranging from texture to coloration. In choosing the preferred finishing and decorative materials, housing owners, users and prospective owners have attendant underlying factors and reasons for their choices. These choice activities usually provoke and invoke certain perceptual orientations that underlie the choices. These perceptual orientations are normally very complex and can only be disentangled by elicitation. This paper presents perceptual orientations of prospective house owners‟ choice and preference for interior walls finishes in Yola, Nigeria. The study was conducted within the theoretical and conceptual framework of means-end chain (MEC model. 15 prospective house owners were interviewed using the laddering interviewing technique after a structured questionnaire survey was carried out. The results showed that twelve (12 identified unique perceptual orientation pathways were established, motivated by four (4 user values, and intervened by four (4 expected functional affordances. The findings disentangled the design expectations of housing users/owners for finishing their housing interiors which can be pointers for designers and Architects for their design processes and decisions.

  16. Shock Condition Forensics and Cryptic Phase Transformations from Crystallographic Orientation Relationships in Zircon

    Science.gov (United States)

    Timms, N. E.; Erickson, T. M.; Cavosie, A. J.; Pearce, M. A.; Reddy, S. M.; Zanetti, M.; Tohver, E.; Schmieder, M.; Nemchin, A. A.; Wittmann, A.

    2016-08-01

    We present an approach to constrain pressure and temperature conditions during impact events involving identification of cryptic histories of phase transformations from orientation relationships in shocked zircon, linked to new P-T phase diagrams.

  17. A Precipitate-Strengthening Model Based on Crystallographic Anisotropy, Stress-Induced Orientation, and Dislocation of Stress-Aged Al-Cu-Mg Single Crystals

    Science.gov (United States)

    Guo, Xiaobin; Zhang, Yong; Zhang, Jin; Deng, Yunlai; Zhang, Xinming

    2017-10-01

    We investigate the relationship between inhomogeneously distributed S precipitates and hardness of stress-aged single-crystal Al-Cu-Mg. First, the effect of crystallographic anisotropy is considered and modeled from the results of free-stress aged single-crystal Al-1.2Cu-0.5Mg with ( 1\\bar{1}8 ), ( \\bar{1}\\bar{2}5 ), (356), and (319) plane orientations. Effect of crystallographic anisotropy depends on the angle between the plane orientation of the single crystal and {012} habit planes of the S precipitates. Second, the effects of the magnitude of the applied stress and direction on the S-laths' size and distribution are considered. As the applied stress-induced S-laths inhomogeneously distribute during aging, the effect of the single-crystal's orientation on the distribution of S-laths is modeled. The results show that a single crystal near (111) plane orientation has the lowest stress-orienting effect. Finally, at higher applied stresses, such as 50 MPa, the S precipitates disperse more homogeneously due to the influence of the dislocations. Inhibiting the effect of dislocation depends on the angle between the plane orientation of the single crystal and the {111} dislocation slide planes. A precipitate-strengthening model of the stress-aged Al-Cu-Mg alloys is established based on crystallographic anisotropy, stress-orienting precipitates, and inhibiting the effect of dislocations.

  18. Crystallographic orientation and electrode nature are key factors for electric current generation by Geobacter sulfurreducens.

    Science.gov (United States)

    Maestro, Beatriz; Ortiz, Juan M; Schrott, Germán; Busalmen, Juan P; Climent, Víctor; Feliu, Juan M

    2014-08-01

    We have investigated the influence of electrode material and crystallographic structure on electron transfer and biofilm formation of Geobacter sulfurreducens. Single-crystal gold-Au(110), Au(111), Au(210)-and platinum-Pt(100), Pt(110), Pt(111), Pt(210)-electrodes were tested and compared to graphite rods. G. sulfurreducens electrochemically interacts with all these materials with different attachment kinetics and final current production, although redox species involved in the electron transfer to the anode are virtually the same in all cases. Initial bacterial colonization was fastest on graphite up to the monolayer level, whereas gold electrodes led to higher final current densities. Crystal geometry was shown to have an important influence, with Au(210) sustaining a current density of up to 1442±101μAcm(-2) at the steady state, over Au(111) with 961±94μAcm(-2) and Au(110) with 944±89μAcm(-2). On the other hand, the platinum electrodes displayed the lowest performances, including Pt(210). Our results indicate that both crystal geometry and electrode material are key parameters for the efficient interaction of bacteria with the substrate and should be considered for the design of novel materials and microbial devices to optimize energy production.

  19. Electromechanical characterization of [Formula: see text] crystals as a function of crystallographic orientation and temperature.

    Science.gov (United States)

    Zhang, Shujun; Luo, Jun; Hackenberger, Wesley; Sherlock, Nevin P; Meyer, Richard J; Shrout, Thomas R

    2009-05-15

    Relaxor based [Formula: see text] ternary single crystals (PIN-PMN-PT) were reported to have broader temperature usage range [Formula: see text] and comparable piezoelectric properties to [Formula: see text] (PMNT) crystals. In this work, the orientation dependent dielectric, piezoelectric and electromechanical properties for PIN-PMN-PT crystals were investigated along [Formula: see text] and [Formula: see text] directions. The electromechanical couplings [Formula: see text] and [Formula: see text] for [Formula: see text] poled crystals were found to be 0.91 and 0.91, respectively, with piezoelectric coefficients [Formula: see text] and [Formula: see text] on the order of 925 and -1420 pC/N. Of particular significance was the mechanical quality factor [Formula: see text] for [Formula: see text] oriented crystals, which was found to be [Formula: see text], much higher than the [Formula: see text] values of [Formula: see text] oriented relaxor-PT crystals [Formula: see text]. The temperature dependence of the piezoelectric properties exhibited good temperature stability up to their ferroelectric phase transition [Formula: see text], indicating [Formula: see text] and [Formula: see text] oriented PIN-PMN-PT are promising materials for transducer applications, with the latter for high power resonant devices where low loss (high [Formula: see text]) was required.

  20. Superior Pre-Osteoblast Cell Response of Etched Ultrafine-Grained Titanium with a Controlled Crystallographic Orientation

    Science.gov (United States)

    Baek, Seung Mi; Shin, Myeong Hwan; Moon, Jongun; Jung, Ho Sang; Lee, See Am; Hwang, Woonbong; Yeom, Jong Taek; Hahn, Sei Kwang; Kim, Hyoung Seop

    2017-03-01

    Ultrafine-grained (UFG) Ti for improved mechanical performance as well as its surface modification enhancing biofunctions has attracted much attention in medical industries. Most of the studies on the surface etching of metallic biomaterials have focused on surface topography and wettability but not crystallographic orientation, i.e., texture, which influences the chemical as well as the physical properties. In this paper, the influences of texture and grain size on roughness, wettability, and pre-osteoblast cell response were investigated in vitro after HF etching treatment. The surface characteristics and cell behaviors of ultrafine, fine, and coarse-grained Ti were examined after the HF etching. The surface roughness during the etching treatment was significantly increased as the orientation angle from the basal pole was increased. The cell adhesion tendency of the rough surface was promoted. The UFG Ti substrate exhibited a higher texture energy state, rougher surface, enhanced hydrophilic wettability, and better cell adhesion and proliferation behaviors after etching than those of the coarse- and fine-grained Ti substrates. These results provide a new route for enhancing both mechanical and biological performances using etching after grain refinement of Ti.

  1. Quantification of thin film crystallographic orientation using X-ray diffraction with an area detector

    Energy Technology Data Exchange (ETDEWEB)

    Baker, Jessica L; Jimison, Leslie H; Mannsfeld, Stefan; Volkman, Steven; Yin, Shong; Subramanian, Vivek; Salleo, Alberto; Alivisatos, A Paul; Toney, Michael F

    2010-02-19

    As thin films become increasingly popular (for solar cells, LEDs, microelectronics, batteries), quantitative morphological information is needed to predict and optimize the film's electronic, optical and mechanical properties. This quantification can be obtained quickly and easily with X-ray diffraction using an area detector and synchrotron radiation in two simple geometries. In this paper, we describe a methodology for constructing complete pole figures for thin films with fiber texture (isotropic in-plane orientation). We demonstrate this technique on semicrystalline polymer films, self-assembled nanoparticle semiconductor films, and randomly-packed metallic nanoparticle films. This method can be immediately implemented to help understand the relationship between film processing and microstructure, enabling the development of better and less expensive electronic and optoelectronic devices.

  2. Preparation of highly preferred orientation TiB2 coatings

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    This paper focuses on the preparation of titanium diboride (TiB2) coatings on the graphite substrate by continuous current plating (CCP) and pulse current plating (PIC) electrochemical techniques in fluoride electrolytes (LiF-NaF-KF)containing K2TiF6 and KBF4 as the electrochemically-active components at 700℃. Thick leveled and uniform coatings were obtained and were composed of relatively pure TiB2. The effect of the experimental parameters on the microstructure of the coatings was studied. The results showed the electrodeposition with PIC produced coatings with better quality, when compared with those obtained by CCP, under the conditions of the current density i = 0.6 A/cm2, frequency = 100 Hz, and ton/toff = 4/1. XRD analysis indicated that the preferred orientation of coatings is (110) plane, which is in accordance with the prediction of the two-dimensional crystal nuclei theory. The effect of a ratio of ton/toff and frequency on the crystal size, texture coefficient and microstress was also investigated.

  3. Enhanced Light Scattering by Preferred Orientation Control of Ga Doped ZnO Films Prepared through MOCVD

    Directory of Open Access Journals (Sweden)

    Long Giang Bach

    2016-01-01

    Full Text Available We have explored the effective approach to fabricate GZO/ZnO films that can make the pyramidal surface structures of GZO films for effective light scattering by employing a low temperature ZnO buffer layer prior to high temperature GZO film growth. The GZO thin films exhibit the typical preferred growth orientations along the (002 crystallographic direction at deposition temperature of 400°C and SEM showed that column-like granule structure with planar surface was formed. In contrast, GZO films with a pyramidal texture surface were successfully developed by the control of (110 preferred orientation. We found that the light diffuse transmittance of the film with a GZO (800 nm/ZnO (766 nm exhibited 13% increase at 420 nm wavelength due to the formed large grain size of the pyramidal texture surface. Thus, the obtained GZO films deposited over ZnO buffer layer have high potential for use as front TCO layers in Si-based thin film solar cells. These results could develop the potential way to fabricate TCO based ZnO thin film using MOCVD or sputtering techniques by depositing a low temperature ZnO layer to serve as a template for high temperature GZO film growth. The GZO films exhibited satisfactory optoelectric properties.

  4. Quantitative orientation preference and susceptibility to space motion sickness simulated in a virtual reality environment.

    Science.gov (United States)

    Chen, Wei; Chao, Jian-Gang; Chen, Xue-Wen; Wang, Jin-Kun; Tan, Cheng

    2015-04-01

    Orientation preference should appear when variable weightings of spatial orientation cues are used between individuals. It is possible that astronauts' orientation preferences could be a potential predictor for susceptibility to space motion sickness (SMS). The present study was conducted to confirm this relationship on Earth by quantifying orientation preferences and simulating SMS in a virtual reality environment. Two tests were carried out. The first was to quantitatively determine one's orientation preference. Thirty-two participants' vision and body cue preferences were determined by measuring perceptual up (PU) orientations. The ratio of vision and body vector (ROVB) was used as the indicator of one's orientation preference. The second test was to visually induce motion sickness symptoms that represent similar sensory conflicts as SMS using a virtual reality environment. Relationships between ROVB values and motion sickness scores were analyzed, which revealed cubic functions by using optimal fits. According to ROVB level, participants were divided into three groups - body group, vision group, and confusion group - and the factor of gender was further considered as a covariate in the analysis. Consistent differences in motion sickness scores were observed between the three groups. Thus, orientation preference had a significant relationship with susceptibility to simulated SMS symptoms. This knowledge could assist with astronaut selection and might be a useful countermeasure when developing new preflight trainings. Copyright © 2015. Published by Elsevier Inc.

  5. Preferred orientation in carbon and boron nitride: Does a thermodynamic theory of elastic strain energy get it right. [C; BN

    Energy Technology Data Exchange (ETDEWEB)

    McCarty, K.F. (Sandia National Laboratories, Livermore, California 94550 (United States))

    1999-09-01

    We address whether the elastic strain-energy theory (minimizing the Gibbs energy of a stressed crystal) of McKenzie and co-workers [D. R. McKenzie and M. M. M. Bilek, J. Vac. Sci. Technol. A [bold 16], 2733 (1998)] adequately explains the preferred orientation observed in carbon and BN films. In the formalism, the Gibbs energy of the cubic materials diamond and cubic boron includes the strain that occurs when the phases form, through specific structural transformations, from graphitic precursors. This treatment violates the requirement of thermodynamics that the Gibbs energy be a path-independent, state function. If the cubic phases are treated using the same (path-independent) formalism applied to the graphitic materials, the crystallographic orientation of lowest Gibbs energy is not that observed experimentally. For graphitic (hexagonal) carbon and BN, an elastic strain approach seems inappropriate because the compressive stresses in energetically deposited films are orders of magnitude higher than the elastic limit of the materials. Furthermore, using the known elastic constants of either ordered or disordered graphitic materials, the theory does not predict the orientation observed by experiment. [copyright] [ital 1999 American Vacuum Society.

  6. Crystallographic orientations and electrical properties of Bi sub 3 sub . sub 4 sub 7 La sub 0. sub 8 sub 5 Ti sub 3 O sub 1 sub 2 thin films on Pt/Ti/SiO sub 2 /Si and Pt/SiO sub 2 /Si substrates

    CERN Document Server

    Ryu, S O; Lee, W J

    2003-01-01

    We report on the crystallization and electrical properties of Bi sub 3 sub . sub 4 sub 7 La sub 0 sub . sub 8 sub 5 Ti sub 3 O sub 1 sub 2 (BLT) thin films for possible ferroelectric non-volatile memory applications. The film properties were found to be strongly dependent on process conditions especially on the intermediate heat treatment conditions. The crystallographic orientation of the films showed sharp changes at the intermediate rapid thermal annealing (RTA) temperature of 450degC. Below 450degC, BLT thin films have (117) orientation while they have preffered c-axis orientation above 450degC. We found that RTA conditions of the first coating layer play a major role in determining the entire crystallographic orientation of the films. The films also showed of ferroelectric hysterisis behavior strongly dependent on RTA treatment. In fact, the remanent polarization of Bi sub 3 sub . sub 4 sub 6 sub 5 La sub 0 sub . sub 8 sub 5 Ti sub 3 O sub 1 sub 2 thin films having (001) preferred crystallographic orient...

  7. Lattice preferred orientations of olivine in the schistosed antigorite serpentinite

    Science.gov (United States)

    Soda, Y.; Ando, J.; Mizukami, T.; Morishita, T.

    2011-12-01

    The lattice preferred orientation (LPO) of the schistosed antigorite serpentinite is considered as causes of the seismic anisotropy observed at the subduction zones (Katayama et al., 2009; Jung, 2011) and the natural examples are reported by several researchers (Bezacier et al., 2010; Hirauchi et al., 2010; Soda and Takagi, 2010). Formation process of the antigorite LPO is unclear, especially at primary serpentinized stage. To understand the development of micro-structures of antigorite serpentinite, we made structural analyses of serpentinite schist and the former peridotite fabric. Samples were taken from lenticular serpentinite bodies (growth in pressure shadows and pull-apart of olivine porphyroclast. In the less serpentinized part, antigorite blades are crystallized along the grain boundary of olivine. We measure the LPOs of coarse olivine grains in the serpentinite schist using a u-stage. The X, Y and Z directions represent directions of lineation, normal to lineation within the foliation and normal to foliation, respectively. The LPOs of olivine show point maximum or partial girdle distribution, and these concentrated crystal axes are incongruous with X, Y and Z direction. The a[100] axes of olivine are parallel to the serpentinite foliation, and form a point maximum several degrees away from the Y direction. The b[010] axes and the c[001] axes are concentrated Z and X direction forming a partial girdle normal to Y direction, respectively. Boudier et al. (2010) have reported the topotactic relationship between olivine and antigorite. They show that the (100)ol is parallel to the (001)atg or the (010)ol is parallel to the (001)atg. And, the a[100] axes of olivine are normal to serpentinite foliation with point maximum in the thin section scale. However, in the case of this study, the simple topotactic relationship does not connect the fabric in the thin section scale of serpentinite schist. Although, more detail analysis need to discuss the formation of

  8. The Relationship Between Interpersonal Relations Orientations and Preferred Classroom Physical Settings.

    Science.gov (United States)

    Feitler, Fred C.; And Others

    This study reports relationships found between FIRO-B (Fundamental Interpersonal Relations Orientation) scores and preference for classroom spatial settings. It was hypothesized that differences in interpersonal needs would be reflected in preferences for particular physical environments in which to teach. The sample consisted of 276 graduates and…

  9. Preference for concentric orientations in the mouse superior colliculus

    NARCIS (Netherlands)

    Ahmadlou, Mehran; Heimel, J Alexander

    2015-01-01

    The superior colliculus is a layered structure important for body- and gaze-orienting responses. Its superficial layer is, next to the lateral geniculate nucleus, the second major target of retinal ganglion axons and is retinotopically organized. Here we show that in the mouse there is also a

  10. Preferred Negative Geotactic Orientation in Mobile Cells: Tetrahymena Results

    Science.gov (United States)

    Noever, David A.; Cronise, Raymond; Matsos, Helen C.

    1994-01-01

    For the protozoan species Tetrahymena a series of airplane experiments are reported, which varied gravity as an active laboratory parameter and tested for corresponding changes in geotaxic orientation of single cells. The airplane achieved altemating periods of low (0.01 g) and high (1.8 g, g = 980 cm/s) gravity by flying repeated Keplerian parabolas. The experimental design was undertaken to clearly distinguish gravity from competing aerodynamic and chemical gradients. In this way, each culture served as its own control, with gravity level alone determining the orientational changes. On average, 6.3% of the Tetrahymena oriented vertically in low gravity, while 27% oriented vertically in high-gravity phases. Simplified physical models are explored for describing these cell trajectores as a function of gravity, aerodynamic drag, and lift. The notable effect of gravity on turning behavior is emphasized as the biophysical cause of the observed negative geotaxis in Tetrahymena. A fundamental investigation of the biological gravity receptor (it it exists) and improved modeling for vertical migration in important types of ocean plankton motivate the present research.

  11. Preference Bias of Head Orientation in Choosing between Two Non-durables

    Directory of Open Access Journals (Sweden)

    Hiroyuki eFunaya

    2015-06-01

    Full Text Available The goal of this study is to investigate how customers’ gaze, head and body orientations reflect their choices. Although the relationship between human choice and gaze behavior has been well studied, other behaviors such as head and body are unknown. We conducted a two-alternatives-forced-choice task to examine (1 whether preference bias, i.e. a positional bias in gaze, head and body toward the item that was later chosen, exists in choice, (2 when preference bias is observed and when prediction of the resulting choice becomes possible (3 whether human choice is affected when the body orientations are manipulated. We used real non-durable products (cheap snacks and clothing on a shopping shelf. The results showed that there was a significant preference bias in head orientation at the beginning one second when the subjects stood straight toward the shelf, and that the head orientation was more biased toward the selected item than the gaze and the center of pressure at the ending one second. Manipulating body orientation did not affect the result of choice. The preference bias detected by observing the head orientation would be useful in marketing science for predicting customers’ choice.

  12. Left and right brain-oriented hemisity subjects show opposite behavioral preferences

    Directory of Open Access Journals (Sweden)

    Bruce Eldine Morton

    2012-11-01

    Full Text Available Introduction: Recently, three independent, intercorrelated biophysical measures have provided the first quantitative measures of a binary form of behavioral laterality called Hemisity, a term referring to inherent opposite right or left brain-oriented differences in thinking and behavioral styles. Crucially, the right or left brain-orientation of individuals assessed by these methods was later found to be essentially congruent with the thicker side of their ventral gyrus of the anterior cingulate cortex (vgACC as revealed by a 3 minute MRI procedure. Laterality of this putative executive structural element has thus become the primary standard defining individual hemisity. Methods: Here, the behavior of 150 subjects, whose hemisity had been calibrated by MRI, was assessed using five MRI-calibrated preference questionnaires, two of which were new.Results: Right and left brain-oriented subjects selected opposite answers (p > 0.05 for 47 of the 107 either-or, forced choice type preference questionnaire items. Hemisity subtype preference differences were present in several areas. They were in: a. logical orientation, b. type of consciousness, c. fear level and sensitivity, d. social-professional orientation, and e. pair bonding-spousal dominance style.Conclusions: The right and left brain-oriented hemisity subtype subjects, sorted on the anatomical basis of upon which brain side their vgACC was thickest, showed numerous significant differences in their either-or type of behavioral preferences.

  13. Preference bias of head orientation in choosing between two non-durables.

    Science.gov (United States)

    Funaya, Hiroyuki; Shibata, Tomohiro

    2015-01-01

    The goal of this study is to investigate how customers' gaze, head and body orientations reflect their choices. Although the relationship between human choice and gaze behavior has been well-studied, other behaviors such as head and body are unknown. We conducted a two-alternatives-forced-choice task to examine (1) whether preference bias, i.e., a positional bias in gaze, head and body toward the item that was later chosen, exists in choice, (2) when preference bias is observed and when prediction of the resulting choice becomes possible (3) whether human choice is affected when the body orientations are manipulated. We used real non-durable products (cheap snacks and clothing) on a shopping shelf. The results showed that there was a significant preference bias in head orientation at the beginning 1 s when the subjects stood straight toward the shelf, and that the head orientation was more biased toward the selected item than the gaze and the center of pressure at the ending 1 s. Manipulating body orientation did not affect the result of choice. The preference bias detected by observing the head orientation would be useful in marketing science for predicting customers' choice.

  14. Crystallization and preliminary crystallographic analysis of NAD{sup +}-preferring aldohexose dehydrogenase from the thermoacidophilic archaeon Thermoplasma acidophilum

    Energy Technology Data Exchange (ETDEWEB)

    Yasutake, Yoshiaki [Research Institute of Genome-based Biofactory, National Institute of Advanced Industrial Science and Technology (AIST), 2-17-2-1 Tsukisamu-Higashi, Toyohira-ku, Sapporo 062-8517 (Japan); Nishiya, Yoshiaki [Tsuruga Institute of Biotechnology, Toyobo Co. Ltd, 10-24 Toyo-cho, Tsuruga 914-0047 (Japan); Tamura, Noriko [Research Institute of Genome-based Biofactory, National Institute of Advanced Industrial Science and Technology (AIST), 2-17-2-1 Tsukisamu-Higashi, Toyohira-ku, Sapporo 062-8517 (Japan); Tamura, Tomohiro, E-mail: t-tamura@aist.go.jp [Research Institute of Genome-based Biofactory, National Institute of Advanced Industrial Science and Technology (AIST), 2-17-2-1 Tsukisamu-Higashi, Toyohira-ku, Sapporo 062-8517 (Japan); Laboratory of Molecular Environmental Microbiology, Graduate School of Agriculture, Hokkaido University, Kita-9, Nishi-9, Kita-ku, Sapporo 060-8589 (Japan)

    2006-06-01

    NAD{sup +}-preferring aldohexose dehydrogenase from the thermoacidophilic archaeon T. acidophilum was crystallized using the hanging-drop vapour-diffusion technique and X-ray diffraction data were collected to a resolution of 2.8 Å. The aldohexose dehydrogenase from the thermoacidophilic archaeon Thermoplasma acidophilum (AldT) is a 28 kDa molecular-weight enzyme that catalyzes the oxidation of various aldohexoses, with a preference for NAD{sup +} rather than NADP{sup +} as a cofactor. The recombinant AldT was crystallized using the hanging-drop vapour-diffusion technique at 293 K under several acidic conditions with polyethylene glycol (PEG) and ammonium sulfate as precipitants. Optimization of the initial crystallizations conditions yielded single crystals in solution containing 0.1 M sodium acetate pH 4.6, 18%(w/v) PEG 4000, 0.2 M ammonium sulfate and 15%(v/v) glycerol. An X-ray diffraction data set was collected to a resolution of 2.8 Å.

  15. Lower limb preference on goal-oriented tasks in unilateral prosthesis users.

    Science.gov (United States)

    Howard, Charla; Wallace, Chris; Stokic, Dobrivoje S

    2012-06-01

    The aim of this study was to determine lower limb preference in 31 prosthesis users and 19 able-bodied controls on 11 goal-oriented tasks in free-standing and supported conditions. The action leg used in 6 or more tasks was considered the preferred leg. We hypothesized that the prosthetic leg in amputees would be used as the preferred leg as often as the dominant leg in controls. For prosthesis users in the free-standing condition, 65% used the prosthetic leg as the preferred leg. This was significantly different (p<0.003) from able-bodied controls, where 100% used the dominant leg as the preferred leg. This discrepancy became even more pronounced in the supported condition and was overall more prevalent among those who used prosthesis for more than 10 years. These findings may have implications for therapy and gait training.

  16. Mining or Tourism: The Development Preference of Settlers Along Pagatban River in Negros Oriental, Philippines

    Directory of Open Access Journals (Sweden)

    Enrique G. Oracion

    2015-06-01

    Full Text Available This paper examines the development preference of settlers surveyed along the upstream, midstream, and downstream sections of Pagatban River in Negros Oriental in central Philippines. The majority of 120 respondents, equally distributed along the three sections of the river, are against the restoration of mining but are in favor of tourism development considering the ecological costs and economic benefits they have to bear with and enjoy, respectively. Specif ically, the data show that the number of respondents who do not prefer the restoration of mining is highest among downstream households while the number of those who do not prefer tourism development is highest among upstream households. The midstream respondents generally prefer both development projects. The chi-square test proves signif icant differences in the development preferences of respondents across settlements along the river. There are also significant differences in tourism preference according to the sex of the respondents, and in mining preference according to farm access, and monthly income of their households. The significant differences in household farm access and income relative to their locations further explain why economic and geographic variations result in divided preference for mining. Given that tourism development is preferred over restoration of mining, how the former’s benefits can be enjoyed across settlements should be looked into and planned with genuine community participation.

  17. Determination of crystallographic orientation of lead-free piezoelectric (K,Na)NbO{sub 3} epitaxial thin films grown on SrTiO{sub 3} (100) surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Qi; Zhu, Fang-Yuan; Cheng, Li-Qian; Wang, Ke; Li, Jing-Feng, E-mail: jingfeng@mail.tsinghua.edu.cn [State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, 100084 Beijing (China)

    2014-03-10

    Crystallographic structure of sol-gel-processed lead-free (K,Na)NbO{sub 3} (KNN) epitaxial films on [100]-cut SrTiO{sub 3} single-crystalline substrates was investigated for a deeper understanding of its piezoelectric response. Lattice parameter measurement by high-resolution X-ray diffraction and transmission electron microscopy revealed that the orthorhombic KNN films on SrTiO{sub 3} (100) surfaces are [010] oriented (b-axis-oriented) rather than commonly identified c-axis orientation. Based on the crystallographic orientation and corresponding ferroelectric domain structure investigated by piezoresponse force microscopy, the superior piezoelectric property along b-axis of epitaxial KNN films than other orientations can be explained.

  18. Curriculum Design Orientations Preference Scale of Teachers: Validity and Reliability Study

    Science.gov (United States)

    Bas, Gokhan

    2013-01-01

    The purpose of this study was to develop a valid and reliable scale for preferences of teachers in regard of their curriculum design orientations. Because there was no scale development study similar to this one in Turkey, it was considered as an urgent need to develop such a scale in the study. The sample of the research consisted of 300…

  19. Control over the preferred orientation of CIGS films deposited by magnetron sputtering using a wetting layer

    Science.gov (United States)

    Yan, Yong; Jiang, Fan; Liu, Lian; Yu, Zhou; Zhang, Yong; Zhao, Yong

    2016-01-01

    A growth method is presented to control the preferred orientation in chalcopyrite CuIn x Ga1- x Se2 (CIGS) thin films grown by magnetron sputtering. Films with (220/204) and (112) preferred orientation as well as randomly oriented films were prepared. The effects of an In2Se3 wetting layer and the working pressure on the texture transition phenomena were examined. A large-grained CIGS film with (220/204) texture was formed at 400°C with the inclusion of a thin (80 nm) In2Se3 layer and liquid phase (excess copper selenide phase) formation, and the reaction mechanism is proposed. The device deposited at 2.0 Pa on an In2Se3 layer exhibited the optimal electrical properties. [Figure not available: see fulltext.

  20. What to wear when practicing oriental medicine: patients' preferences for doctors' attire.

    Science.gov (United States)

    Chang, Dong-Seon; Lee, Hyeyeon; Lee, Hyejung; Park, Hi-Joon; Chae, Younbyoung

    2011-08-01

    The patient's impression of the doctor is an important factor in a clinical consultation, and the doctor's attire also plays a great role in promoting trust and confidence in the patients. Previous studies have shown that a doctor in a white coat will appear more professional, confident, and trustworthy. The objective of this study was to investigate whether the influence of a doctor's attire applies for both Western and Oriental medical doctors. Before a clinical consultation, 153 patients were asked to assess photographs showing an identical doctor wearing four different dress styles. The patients were divided into two groups: One group was told that the doctor in the photograph was a Western doctor, whereas the other group was told that the doctor was an Oriental medical doctor. Patients' ratings of preference for competency, trustworthiness, comfortableness, and treatment choice were then measured and compared. Patients preferred a doctor in a white coat the most, giving highest ratings for competency and trustworthiness, while reporting to feel most comfortable with a doctor in traditional dress. No difference was found between Western and Oriental medical doctors. Patients prefer their doctors to wear white coats, regardless of whether the doctor is a Western or Oriental medical doctor, even though patients feel more comfortable with doctors wearing traditional dress. The preference about doctors' attire symbolizes the perception of patients regarding their doctor's image. Taking the historical and symbolic meaning of the doctor's white coat together, this clear preference of patients for the white coat might imply that patients require a more scientific and professional image, regardless of whether the doctors are Western or Oriental medical doctors.

  1. Correction of intensities for preferred orientation in neutron-diffraction data of NiTi shape-memory alloy using the generalized spherical-harmonic description

    CERN Document Server

    Sitepu, H; Stalick, J K

    2002-01-01

    Analysis of quantitative texture (crystallographic preferred orientation, PO) in polycrystalline materials is of interest not only because the PO gives errors in quantitative phase analysis, but also because it can affect the results of structure determination from powder diffraction data. In the present study, texture characterization of the polycrystalline Ni-rich NiTi shape-memory alloy (SMA) of nominal composition 50.14 atomic percent nickel has been carried out using the BT-1 high-resolution, fixed-wavelength, 32-detector powder diffractometer at the NIST Center for Neutron Research. Data were collected along the differential scanning calorimeter (DSC) heating curve. The results obtained from Rietveld refinement with the generalized spherical harmonic (GSH) description for all neutron diffraction data sets show that the weight percentages for monoclinic and cubic phases during the phase transition are consistent with the DSC heating curve. (orig.)

  2. Human infants' preference for left-to-right oriented increasing numerical sequences.

    Directory of Open Access Journals (Sweden)

    Maria Dolores de Hevia

    Full Text Available While associations between number and space, in the form of a spatially oriented numerical representation, have been extensively reported in human adults, the origins of this phenomenon are still poorly understood. The commonly accepted view is that this number-space association is a product of human invention, with accounts proposing that culture, symbolic knowledge, and mathematics education are at the roots of this phenomenon. Here we show that preverbal infants aged 7 months, who lack symbolic knowledge and mathematics education, show a preference for increasing magnitude displayed in a left-to-right spatial orientation. Infants habituated to left-to-right oriented increasing or decreasing numerical sequences showed an overall higher looking time to new left-to-right oriented increasing numerical sequences at test (Experiment 1. This pattern did not hold when infants were presented with the same ordinal numerical information displayed from right to left (Experiment 2. The different pattern of results was congruent with the presence of a malleable, context-dependent baseline preference for increasing, left-to-right oriented, numerosities (Experiment 3. These findings are suggestive of an early predisposition in humans to link numerical order with a left-to-right spatial orientation, which precedes the acquisition of symbolic abilities, mathematics education, and the acquisition of reading and writing skills.

  3. Neuroticism and State Differences in Partisanship in the USA: Emotional Stability, Ideological Orientation, and Republican Preference

    Directory of Open Access Journals (Sweden)

    Stewart J. H. McCann

    2014-09-01

    Full Text Available Relations between Neuroticism, Republican-Democrat preference, and conservative-liberal ideological orientation were examined with the states of the USA as units of analysis. State-aggregated Neuroticism scores were based on 1999-2005 responses of 619,397 residents to the 44-item Big Five Inventory. State Republican-Democrat preference was based on the 2002 occupancy of the U.S. Presidency, U.S. House, U.S. Senate, state House, state Senate, and state Governorship, as well as state-aggregated partisanship responses of 110,305 persons to 1998-2002 CBS/New York Times national polls. State conservative-liberal ideological orientation was based on 1998-2002 state-aggregated responses of 103,828 persons to CBS/New York Times national polls. Using correlation, partial correlation, and hierarchical multiple regression, it was determined that lower state resident Neuroticism is associated with Republican preference, and that both conservative-liberal ideological orientation and state resident Neuroticism account independently for variance in Republican-Democrat preference. These relations were found when 1998-2002 state socioeconomic status, white percent, and urban percent were statistically considered and controlled in partial correlation and hierarchical regression analysis. In contrast, corresponding analyses involving the other Big Five showed that only Openness and Conscientiousness showed any relation to partisanship, albeit infrequent and inconsistent. State resident Neuroticism is the primary state-level Big Five predictor of Republican/Democratic Party choice.

  4. Microstructural studies and crystallographic orientation of different zones and δ-hydrides in resistance welded Zircaloy-4 sheets

    Science.gov (United States)

    Kiran Kumar, N. A. P.; Szpunar, Jerzy. A.; He, Zhang

    2011-07-01

    The cold worked stress relieved (CWSR) Zircaloy-4 sheet used as endplate in nuclear fuel bundle is resistance welded with an endcap in argon environment. Later the welded sample is hydrided in a gaseous atmosphere at 400 °C. Optical microscopy (OM), electron backscatter diffraction (EBSD) and X-ray diffraction (XRD) were used to examine the morphology and crystal orientation of the hydrides. The microstructural changes in different areas of the weld zone, heat affected zone (HAZ) and the as-received zone were analyzed using EBSD technique. Optical examination showed complete random morphological orientation of hydrides and predominantly basket-weave structure in the weld zone, with very few colonies of parallel plate structures. Variant selection for α-phase formation inside prior β-grains was identified at the weld centre. As we move from the weld centre to the as-received zone, the variant selection is found to be less probable. The δ-hydride platelets at the weld zone were always found to be growing perpendicular to the α-colonies having angular difference of 60-63° and follow (0 0 0 1) α-Zr//{1 1 1}δ-ZrH 1.5 orientation relationship with the zirconium matrix. Proposed description of complex distribution of hydrides and alloy microstructure at the weld and heat affected zone will contribute to a better understanding of mechanisms of failure of fuel cladding in various types of nuclear reactors.

  5. Static Recrystallization Kinetics and Crystallographic Texture of Nb-Stabilized Ferritic Stainless Steel Based on Orientation Imaging Microscopy

    Science.gov (United States)

    Malta, Paula Oliveira; Alves, Davi Silva; Ferreira, Aline Oliveira Vasconcelos; Moutinho, Iane Dutra; Dias, Carolina Arriel Pedroso; Santos, Dagoberto Brandão

    2017-03-01

    In the present study, Nb-stabilized ferritic stainless steel was prepared with annealing (430-A) and without annealing (430-NA) annealing, and the microstructure of the resulting samples was examined. The steel was then subjected to cold rolling and isothermal annealing in order to analyze its recrystallization kinetics and texture evolution. Microstructural characterization was performed by scanning and transmission electron microscopies. Recrystallization kinetics were evaluated by measuring the microhardness of the samples, and analyzing their kernel average misorientation and grain orientation spread via electron backscatter diffraction. The Avrami exponent data revealed that one-dimensional grain growth occurred owing to the migration of high-angle grain boundaries. The mean activation energies for recrystallization for 430-NA and 430-A was found to be 365 and 419 kJ mol-1, respectively. The recrystallization texture was influenced by oriented nucleation and selected growth mechanisms, as well as by the Nb carbonitride distribution and grain boundary energy. The recrystallized and growing grains with the {554} orientation showed a dimensional advantage over the other recrystallized components. The coincident site lattice boundaries were attributed to the progression of recrystallization since the CSL numeric fraction increased as the temperature increased. The {554} component was associated with the ∑19a boundary, which exerted a significant control on the selective growth during the recrystallization.

  6. Static Recrystallization Kinetics and Crystallographic Texture of Nb-Stabilized Ferritic Stainless Steel Based on Orientation Imaging Microscopy

    Science.gov (United States)

    Malta, Paula Oliveira; Alves, Davi Silva; Ferreira, Aline Oliveira Vasconcelos; Moutinho, Iane Dutra; Dias, Carolina Arriel Pedroso; Santos, Dagoberto Brandão

    2017-01-01

    In the present study, Nb-stabilized ferritic stainless steel was prepared with annealing (430-A) and without annealing (430-NA) annealing, and the microstructure of the resulting samples was examined. The steel was then subjected to cold rolling and isothermal annealing in order to analyze its recrystallization kinetics and texture evolution. Microstructural characterization was performed by scanning and transmission electron microscopies. Recrystallization kinetics were evaluated by measuring the microhardness of the samples, and analyzing their kernel average misorientation and grain orientation spread via electron backscatter diffraction. The Avrami exponent data revealed that one-dimensional grain growth occurred owing to the migration of high-angle grain boundaries. The mean activation energies for recrystallization for 430-NA and 430-A was found to be 365 and 419 kJ mol-1, respectively. The recrystallization texture was influenced by oriented nucleation and selected growth mechanisms, as well as by the Nb carbonitride distribution and grain boundary energy. The recrystallized and growing grains with the {554} orientation showed a dimensional advantage over the other recrystallized components. The coincident site lattice boundaries were attributed to the progression of recrystallization since the CSL numeric fraction increased as the temperature increased. The {554} component was associated with the ∑19a boundary, which exerted a significant control on the selective growth during the recrystallization.

  7. Synthesis, Magnetic Anisotropy and Optical Properties of Preferred Oriented Zinc Ferrite Nanowire Arrays

    Directory of Open Access Journals (Sweden)

    Xu Yan

    2010-01-01

    Full Text Available Abstract Preferred oriented ZnFe2O4 nanowire arrays with an average diameter of 16 nm were fabricated by post-annealing of ZnFe2 nanowires within anodic aluminum oxide templates in atmosphere. Selected area electron diffraction and X-ray diffraction exhibit that the nanowires are in cubic spinel-type structure with a [110] preferred crystallite orientation. Magnetic measurement indicates that the as-prepared ZnFe2O4 nanowire arrays reveal uniaxial magnetic anisotropy, and the easy magnetization direction is parallel to the axis of nanowire. The optical properties show the ZnFe2O4 nanowire arrays give out 370–520 nm blue-violet light, and their UV absorption edge is around 700 nm. The estimated values of direct and indirect band gaps for the nanowires are 2.23 and 1.73 eV, respectively.

  8. Veteran satisfaction and treatment preferences in response to a posttraumatic stress disorder specialty clinic orientation group.

    Science.gov (United States)

    Schumm, Jeremiah A; Walter, Kristen H; Bartone, Anne S; Chard, Kathleen M

    2015-06-01

    To maximize accessibility to evidence-based treatments for posttraumatic stress disorder (PTSD), the United States Department of Veterans Affairs (VA) has widely disseminated cognitive processing therapy (CPT) and prolonged exposure (PE) therapy to VA clinicians. However, there is a lack of research on veteran preferences when presented with a range of psychotherapy and medication options. This study uses a mixed-method approach to explore veteran satisfaction with a VA PTSD specialty clinic pre-treatment orientation group, which provides education about available PTSD treatment options. This study also tested differences in treatment preference in response to the group. Participants were 183 US veterans. Most were White, male, and referred to the clinic by a VA provider. Results indicated high satisfaction with the group in providing an overview of services and helping to inform treatment choice. Most preferred psychotherapy plus medications (63.4%) or psychotherapy only (30.1%). Participants endorsed a significantly stronger preference for CPT versus other psychotherapies. PE was significantly preferred over nightmare resolution therapy and present-centered therapy, and both PE and cognitive-behavioral conjoint therapy were preferred over virtual reality exposure therapy. Results suggest that by informing consumers about evidence-based treatments for PTSD, pre-treatment educational approaches may increase consumer demand for these treatment options.

  9. Precise Determination of the Crystallographic Orientations in Single ZnS Nanowires by Second-Harmonic Generation Microscopy

    CERN Document Server

    Hongbo, Hu; Hua, Long; Weiwei, Liu; Bing, Wang; Peixiang, Lu

    2015-01-01

    We report on the systematical study of the second-harmonic generation (SHG) in single zinc sulfide nanowires (ZnS NWs). The high quality ZnS NWs with round cross-section were fabricated by chemical vapor deposition method. The transmission electron microscopy images show that the actual growth-axis has a deviation angle of 0o~20o with the preferential growth direction [120], which leads to the various polarization-dependent SHG response patterns in different individual ZnS NWs. The SHG response is quite sensitive to the orientations of c-axis as well as the (100) and (010) crystal-axis of ZnS NWs, thus all the three crystal-axis orientations of ZnS NWs are precisely determined by the SHG method. A high SHG conversion efficiency of 7*10^(-6) is obtained in single ZnS NWs, which shows potential applications in nanoscale ultraviolet light source, nonlinear optical microscopy and nanophotonic devices.

  10. Irregularities of crystallographic orientation and residual stresses in the crossed-lamellar shell as a natural functionally graded material.

    Science.gov (United States)

    Bonarski, Jan T; Checa, Antonio G; Rodriguez-Navarro, Alejandro; Tarkowski, Leszek; Wajda, Wojciech

    2015-12-06

    The microstructures of different groups of molluscs are characterized by preferential orientations of crystallites (texture), leading to a significant anisotropy of the physical properties of the shells. A complementary characteristic, usually neglected, is the distribution of the residual stresses existing within the shell wall. By means of X-ray diffraction, we study the distribution of stresses with thickness in the shell wall of the gastropod Conus marmoreus, which has a microstructure of the crossed-lamellar type. The results revealed an extraordinary texture inhomogeneity and the existence of tensional residual stresses along the shell thickness, the origins of which are unknown. Some of the observed changes in textural parameters and stresses coincide with the transitions between shell layers, although other features are of unknown origin. Our results provide insight into the microstructural regularities that govern the mesoscale construction of shells, such as that of C. marmoreus.

  11. Raman scattering, electrical and optical properties of fluorine-doped tin oxide thin films with (200) and (301) preferred orientation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Chang-Yeoul, E-mail: cykim15@kicet.re.kr [Nano-Convergence Intelligence Material Team, Korea Institute of Ceramic Eng. and Tech., Gasan-digtial-ro 10 Gil 77 Geumcheon-gu, 153-801 Seoul (Korea, Republic of); Riu, Doh-Hyung [Dept. of New Material Sci. and Eng., Seoul National University of Technology, Seoul (Korea, Republic of)

    2014-12-15

    (200) and (301) preferred oriented fluorine-doped tin oxide (FTO) thin films were fabricated by spray pyrolysis of ethanol-added and water-based FTO precursor solutions, respectively. (200) oriented FTO thin film from ethanol-added solution shows the lower electrical resistivity and visible light transmission than (301) preferred thin film from water-based solution. It is due to the higher carrier concentration and electron mobility in (200) oriented crystals, that is, the lower ionized impurity scattering. The higher electron concentration is related to the higher optical band gap energy, the lower visible light transmission, and the higher IR reflection. For (301) preferred FTO thin films from water-based solution, the lower carrier concentration and electron mobility make the higher electrical resistivity and visible light transmission. Raman scattering analysis shows that IR active modes prominent in (200) oriented FTO thin film are related with the lower electrical resistivity. - Highlights: • We coated fluorine-doped tin oxide thin films with preferred orientation of (200) and (301). • We examine changes in the level of electrical and optical properties with the orientation. • (200) preferred orientation showed lower electrical resistivity and optical transmittance. • (200) oriented thin films have higher electron concentrations that are related with IR active modes.

  12. Control of preferred (222) crystalline orientation of sputtered indium tin oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Pham, Duy Phong [Laboratory of Advanced Materials, University of Science, Vietnam National University, Ho Chi Minh (Viet Nam); Phan, Bach Thang [Laboratory of Advanced Materials, University of Science, Vietnam National University, Ho Chi Minh (Viet Nam); Faculty of Materials Science, University of Science, Vietnam National University, Ho Chi Minh (Viet Nam); Hoang, Van Dung; Nguyen, Huu Truong [Laboratory of Advanced Materials, University of Science, Vietnam National University, Ho Chi Minh (Viet Nam); Ta, Thi Kieu Hanh [Faculty of Materials Science, University of Science, Vietnam National University, Ho Chi Minh (Viet Nam); Maenosono, Shinya [Japan Advanced Institute of Science and Technology, Nomi, Ishikawa (Japan); Tran, Cao Vinh, E-mail: tcvinh@hcmus.edu.vn [Laboratory of Advanced Materials, University of Science, Vietnam National University, Ho Chi Minh (Viet Nam)

    2014-11-03

    We report a two-step growth process for the fabrication of (222)-plane textured indium tin oxide (ITO) films. A thin ITO seed layer was grown in mixed Argon + Oxygen gases, followed by a thick ITO deposited in Argon gas. X-Ray diffraction shows that the sputtered ITO films exhibit strongly preferred (222) crystalline orientation. The (222)-plane textured ITO films have high transmittance above 80% in the visible range and carrier concentration, mobility and resistivity in the range of 10{sup 21} cm{sup −3}, 40 cm{sup 2}/Vs and 10{sup −4} Ω·cm, respectively. The surface roughness of our (222) textured ITO films is 1.4 nm, which is one of the smallest value obtained from sputtered ITO thin films. - Highlights: • Control of preferred (222) crystalline orientation of indium tin oxide (ITO) films • A thin oxygen rich seed layer activates (222) orientation growth of overhead ITO films. • The surface roughness of (222)-plane textured ITO films is about 1.4 nm. • Carrier concentration and resistivity are about 10{sup 21} cm{sup −3} and 10{sup −4} Ω·cm, respectively.

  13. Recovery of crystallographic texture in remineralized dental enamel.

    Science.gov (United States)

    Siddiqui, Samera; Anderson, Paul; Al-Jawad, Maisoon

    2014-01-01

    Dental caries is the most prevalent disease encountered by people of all ages around the world. Chemical changes occurring in the oral environment during the caries process alter the crystallography and microstructure of dental enamel resulting in loss of mechanical function. Little is known about the crystallographic effects of demineralization and remineralization. The motivation for this study was to develop understanding of the caries process at the crystallographic level in order to contribute towards a long term solution. In this study synchrotron X-ray diffraction combined with scanning electron microscopy and scanning microradiography have been used to correlate enamel crystallography, microstructure and mineral concentration respectively in enamel affected by natural caries and following artificial demineralization and remineralization regimes. In particular, the extent of destruction and re-formation of this complex structure has been measured. 2D diffraction patterns collected at the European Synchrotron Radiation Facility were used to quantify changes in the preferred orientation (crystallographic texture) and position of the (002) Bragg reflection within selected regions of interest in each tooth slice, and then correlated with the microstructure and local mineral mass. The results revealed that caries and artificial demineralization cause a large reduction in crystallographic texture which is coupled with the loss of mineral mass. Remineralization restores the texture to the original level seen in healthy enamel and restores mineral density. The results also showed that remineralization promotes ordered formation of new crystallites and growth of pre-existing crystallites which match the preferred orientation of healthy enamel. Combining microstructural and crystallographic characterization aids the understanding of caries and erosion processes and assists in the progress towards developing therapeutic treatments to allow affected enamel to regain

  14. Recovery of crystallographic texture in remineralized dental enamel.

    Directory of Open Access Journals (Sweden)

    Samera Siddiqui

    Full Text Available Dental caries is the most prevalent disease encountered by people of all ages around the world. Chemical changes occurring in the oral environment during the caries process alter the crystallography and microstructure of dental enamel resulting in loss of mechanical function. Little is known about the crystallographic effects of demineralization and remineralization. The motivation for this study was to develop understanding of the caries process at the crystallographic level in order to contribute towards a long term solution. In this study synchrotron X-ray diffraction combined with scanning electron microscopy and scanning microradiography have been used to correlate enamel crystallography, microstructure and mineral concentration respectively in enamel affected by natural caries and following artificial demineralization and remineralization regimes. In particular, the extent of destruction and re-formation of this complex structure has been measured. 2D diffraction patterns collected at the European Synchrotron Radiation Facility were used to quantify changes in the preferred orientation (crystallographic texture and position of the (002 Bragg reflection within selected regions of interest in each tooth slice, and then correlated with the microstructure and local mineral mass. The results revealed that caries and artificial demineralization cause a large reduction in crystallographic texture which is coupled with the loss of mineral mass. Remineralization restores the texture to the original level seen in healthy enamel and restores mineral density. The results also showed that remineralization promotes ordered formation of new crystallites and growth of pre-existing crystallites which match the preferred orientation of healthy enamel. Combining microstructural and crystallographic characterization aids the understanding of caries and erosion processes and assists in the progress towards developing therapeutic treatments to allow affected

  15. Optical properties of the cirrus cloud ice crystals with preferred azimuthal orientation for polarization lidars with azimuthal scanning

    Science.gov (United States)

    Konoshonkin, Alexander V.; Kustova, Natalia V.; Nasonov, Sergey V.; Bryukhanov, Ilia D.; Shishko, Viktor A.; Timofeev, Dmitriy N.; Borovoi, Anatoly G.

    2016-10-01

    Optical properties of the cirrus cloud ice crystals with preferred azimuthal orientation are required for current numerical models of the Earth's radiation balance. Retrieving the orientation distributions function of the crystals from a vertically pointing polarization lidar measuring the full Mueller matrix is a very complicated problem because of lake of information. Lidars with zenith scanning can be used only to retrieve the properties of horizontally oriented particles. The paper shows that if the particles have preferred azimuthal orientation, the polarization lidars with azimuthal scanning should be used. It is also shown that all the elements of the Mueller matrix give no extra information compare to the depolarization ratio. Optical properties of preferred azimuthal oriented hexagonal ice columns with size from 10 to 1000 μm for wavelengths of 0.355, 0.532 and 1.064 μm were collected as a data bank.

  16. Social value orientation: theoretical and measurement issues in the study of social preferences.

    Science.gov (United States)

    Murphy, Ryan O; Ackermann, Kurt A

    2014-02-01

    What motivates people when they make decisions and how those motivations are potentially entangled with concerns for others are central topics for the social, cognitive, and behavioral sciences. According to the postulate of narrow self-interest, decision makers have the goal of maximizing personal payoffs and are wholly indifferent to the consequences for others. The postulate of narrow self-interest-which has been influential in economics, psychology, and sociology-is precise and powerful but is often simply wrong. Its inadequacy is well known and efforts have been made to develop reliable and valid measurement methods to quantify the more nuanced social preferences that people really have. In this paper, we report on the emergence and development of the predominant conceptualization of social preferences in psychology: social value orientation (SVO). Second, we discuss the relationship between measurement and theory development of the SVO construct. We then provide an overview of the literature regarding measurement methods that have been used to assess individual variations in social preferences. We conclude with a comparative evaluation of the various measures and provide suggestions regarding the measures' constructive use in building psychologically realistic theories of people's social preferences.

  17. Interactions among the effects of head orientation, emotional expression, and physical attractiveness on face preferences.

    Science.gov (United States)

    Main, Julie C; DeBruine, Lisa M; Little, Anthony C; Jones, Benedict C

    2010-01-01

    Previous studies have shown that preferences for direct versus averted gaze are modulated by emotional expressions and physical attractiveness. For example, preferences for direct gaze are stronger when judging happy or physically attractive faces than when judging disgusted or physically unattractive faces. Here we show that preferences for front versus three-quarter views of faces, in which gaze direction was always congruent with head orientation, are also modulated by emotional expressions and physical attractiveness; participants demonstrated preferences for front views of faces over three-quarter views of faces when judging the attractiveness of happy, physically attractive individuals, but not when judging the attractiveness of relatively unattractive individuals or those with disgusted expressions. Moreover, further analyses indicated that these interactions did not simply reflect differential perceptions of the intensity of the emotional expressions shown in each condition. Collectively, these findings present novel evidence that the effect of the direction of the attention of others on attractiveness judgments is modulated by cues to the physical attractiveness and emotional state of the depicted individual, potentially reflecting psychological adaptations for efficient allocation of social effort. These data also present the first behavioural evidence that the effect of the direction of the attention of others on attractiveness judgments reflects viewer-referenced, rather than face-referenced, coding and/or processing of gaze direction.

  18. Inner Core Anisotropy Due to the Magnetic Field--induced Preferred Orientation of Iron.

    Science.gov (United States)

    Karato, S

    1993-12-10

    Anisotropy of the inner core of the Earth is proposed to result from the lattice preferred orientation of anisotropic iron crystals during their solidification in the presence of a magnetic field. The resultant seismic anisotropy is related to the geometry of the magnetic field in the core. This hypothesis implies that the observed anisotropy (fast velocity along the rotation axis) indicates a strong toroidal field in the core, which supports a strong field model for the geodynamo if the inner core is made of hexagonal close-packed iron.

  19. A qualitative description of preferred orientation in porous carbonate matrices of marine origin

    Energy Technology Data Exchange (ETDEWEB)

    Golan, Yuval; Dahan, David; Vago, Razi

    2003-10-15

    Porous aragonite matrices of marine origin exhibit a prominent preferred orientation in which the (221) crystal planes are aligned perpendicular to the principal growth direction of the organism. Since the aragonite crystallites that compose the matrix appear to be organized perpendicular to the spherical pore surfaces, these apparently conflicting findings can be explained by a bimodal distribution of the crystallites into pore and bulk crystallite populations. Analysis of X-ray diffraction data obtained from matrices taken from eight different organisms was carried out. The validity of the bimodal distribution model was confirmed by correlation with porosity data.

  20. Controlling preferred orientation and electrical conductivity of zinc oxide thin films by post growth annealing treatment

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, J., E-mail: J.Kennedy@gns.cri.nz [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Murmu, P.P.; Leveneur, J. [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand); Markwitz, A. [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand); The MacDiarmid Institute for Advanced Materials and Nanotechnology (New Zealand); Futter, J. [National Isotope Centre, GNS Science, PO Box 31312, Lower Hutt 5010 (New Zealand)

    2016-03-30

    Graphical abstract: - Highlights: • Annealing dependent microstructural evolution and change in conductivity of ZnO films. • Preferential growth along (0 0 2) and (1 0 0) planes in air and vacuum annealed films. • Resistivity varied between 10{sup 6} and 10{sup −2} Ω cm depending on annealing conditions. • Hydrogen interstitials, and hydrogen-oxygen vacancy complexes affect the conductivity. • Narrow ZnO bandgap assigned to band tail effect related to intrinsic defects states. - Abstract: We report the microstructural evolution of the preferred orientation and electrical conductivity of zinc oxide (ZnO) thin films prepared by ion beam sputtering. Elastic recoil detection analysis results showed 0.6 at% H in as-deposited film which decreased to 0.35 at% in air annealed film due to H diffusion. XRD results showed that the preferred orientation can be tuned by selecting annealing conditions. Vacuum annealed films exhibited (1 0 0) orientation, whereas air annealed film showed (0 0 2) orientation. The annealing conditions caused a dramatic increase in the resistivity of air annealed films (∼10{sup 6} Ω cm), whereas vacuum annealed films showed lower resistivity (∼10{sup −2} Ω cm). High resistivity in air annealed film is attributed to the lack of hydrogen interstitials and hydrogen-oxygen vacancy complexes. Raman results supported the XRD results which demonstrated that annealing assisted in recovery of the crystalline disorder in as-deposited films. Air annealed film exhibited the highest optical transmission (89.7%) in the UV–vis region compared to as-deposited and vacuum annealed films (∼85%). Optical bandgap was found to vary between 3.11 eV and 3.18 eV in as-deposited and annealed films, respectively. The bandgap narrowing is associated with the intrinsic defects which introduced defect states resulting in band tail in ZnO films.

  1. Preferred orientation in Cr- and Co-based thin films and its effects on the read/write performance of the media

    Science.gov (United States)

    Tsai, Hsiao-chu; Lal, Brij B.; Eltoukhy, Atef

    1992-04-01

    This work investigates the formation of preferred crystallographic orientation (PO) in Cr underlayer as well as CoCrTa and CoCrPtTa thin films and its effects on the recording performance of longitudinal media. The results show that the thin-film media with comparable coercivity but different crystalline PO as measured by x-ray diffraction exhibit significant difference in high-frequency signal amplitude, pulse width, and signal-to-noise ratio. To illustrate the effect of PO on parametric performance, CoCrTa/Cr and CoCrPtTa/Cr media were sputtered on different substrates and/or using special sputtering processes to achieve comparable coercivity but different PO in the films. A PO of Cr(200), which normally occurs on the NiP/Al substrates under adequate sputtering conditions, is found to be the key to obtaining a PO of Co(11.0) in Co-alloy media. The consequence of preferred in-plane c-axis orientation is a higher coercivity and better parametric performance of the medium. The formation of PO in the Cr underlayer is found to be related to the substrate material and the oxygen content in the sputtered films. The nonmetallic canasite substrates tend to promote PO of more stable Cr(110) rather than Cr(200). Consequently, this leads to a PO of out-of-plane c axis on the following Co films. The PO of magnetic layer appears to be an important factor in determining the parametric performance of the media.

  2. Mineral composition and preferred orientation of minerals in shales from Palaeozoic Baltic Basin

    Science.gov (United States)

    Gąsiński, Arkadiusz

    2017-04-01

    preferred orientation with respect to their elongation quantitatively. It is clear that not only clay minerals but also brittle minerals (quartz, carbonates, feldspars) contribute to anisotropy of shales.

  3. Quartz preferred orientation in naturally deformed mylonitic rocks (Montalto shear zone-Italy): a comparison of results by different techniques, their advantages and limitations

    Science.gov (United States)

    Fazio, Eugenio; Punturo, Rosalda; Cirrincione, Rosolino; Kern, Hartmut; Pezzino, Antonino; Wenk, Hans-Rudolf; Goswami, Shalini; Mamtani, Manish A.

    2016-12-01

    In the geologic record, the quartz c-axis patterns are widely adopted in the investigation of crystallographic preferred orientations (CPO) of naturally deformed rocks. To this aim, in the present work, four different methods for measuring quartz c-axis orientations in naturally sheared rocks were applied and compared: the classical universal stage technique, the computer-integrated polarization microscopy method (CIP), the time-of-flight (TOF) neutron diffraction analysis , and the electron backscatter diffraction (EBSD). Microstructural analysis and CPO patterns of quartz, together with the ones obtained for feldspars and micas in mylonitic granitoid rocks, have been then considered to solve structural and geological questions related to the Montalto crustal scale shear zone (Calabria, southern Italy). Results obtained by applying the different techniques are discussed, and the advantages as well as limitations of each method are highlighted. Importantly, our findings suggest that patterns obtained by means of different techniques are quite similar. In particular, for such mylonites, a subsimple shear (40% simple shear vs 60% pure shear) by shape analysis of porphyroclasts was inferred. A general tendency of an asymmetric c-maximum near to the Z direction (normal to foliation) suggesting dominant basal slip, consistent with fabric patterns related to dynamically recrystallization under greenschist facies, is recognized. Rhombohedral slip was likely active as documented by pole figures of positive and negative rhombs (TOF), which reveal also potential mechanical Dauphiné twinning. Results showed that the most complete CPO characterization on deformed rocks is given by the TOF (from which also other quartz crystallographic axes can be obtained as well as various mineral phases may be investigated). However, this use is restricted by the fact that (a) there are very few TOF facilities around the world and (b) there is loss of any domainal reference, since TOF is a

  4. Crystal preferred orientation of amphibole and implications for seismic anisotropy in the crust

    Science.gov (United States)

    Jung, Haemyeong

    2016-04-01

    Strong seismic anisotropy is often observed in the middle to lower crust and it has been considered to be originated from the crystal preferred orientation (CPO) of anisotropic minerals such as amphibole. Amphibolite is one of the dominant rocks in the middle to lower crust. In this study, crystal preferred orientations of hornblende in amphibolites at Yeoncheon and Chuncheon areas in South Korea were determined by using the electron backscattered diffraction (EBSD)/SEM with HKL Channel 5 software. In Yeoncheon area, hornblende showed two types of CPOs. Type-I CPO is characterized as (100) poles of hornblende aligned subnormal to foliation and [001] axes aligned subparallel to lineation. Type-II CPO is characterized as (100) poles of hornblende aligned subnormal to foliation and (010) poles aligned subparallel to lineation (refer to Ko and Jung, 2015, Nature Communications). In Chuncheon area, three types of CPOs of hornblende were observed. In addition to the type-I and -II CPOs described above, type-III CPO of hornblende was observed in Chuncheon area and it is characterized as (100) poles of hornblende aligned subnormal to foliation and both [001] axes and (010) poles aligned as a girdle subparallel to foliation. Using the observed CPO and the single crystal elastic constant of hornblende, seismic anisotropy of hornblende was calculated. Seismic anisotropy of P-wave was strong in the range of 10.2 - 13.5 %. Seismic anisotropy of S-wave was also strong in the range of 6.9 - 11.2 %. These results show that hornblende deformed in nature can produce a strong CPO, resulting in a strong seismic anisotropy in the middle to lower crust. Taking into account of the CPO of plagioclase in the rock, seismic anisotropies of whole rock turned out to be maximum P-wave anisotropy (Vp) of 9.8% and maximum S-wave anisotropy (Vs) of 8.2%. Therefore, strong seismic anisotropy found in the middle to lower crust in nature can be attributed to the CPO of hornblende in amphibolite.

  5. "LPO Lite" : Representing Lattice Preferred Orientation and its Evolution Using Structured Basis Functions

    Science.gov (United States)

    Ribe, N. M.; Castelnau, O.

    2008-12-01

    Current methods for calculating the evolution of flow-induced seismic anisotropy in the upper mantle describe Lattice Preferred Orientation (LPO) using ensembles of 103-104 individual grains, and are nowaday too computationally expensive to be incorporated into three-dimensional time-dependent convection models. We propose a much faster (by a factor ~ 103) method wherein LPO is described by a small number of 'structured basis functions' (SBFs.) The number of SBFs required is equal to the number of active slip systems (= 3 for olivine), and each SBF represents the 'virtual' LPO that would be produced by the action of just one of those systems. Analytical expressions for the SBFs are obtained using a simple 'single-slip' (SS) model, and are then tested against the predictions of the second-order (SO) self-consistent model of Ponte-Castaneda (J. Mech. Phys. Solids 50, 737-757, 2002) in which several slip systems act simultaneously. Remarkably, the SS model reproduces exactly (99.9% variance reduction) the orientation- dependence of the slip rate ·γ predicted by the SO model for each active slip system, once the overall amplitude of the SS expression for ·γ has been determined by least-squares fitting to the SO prediction. Having thus demonstrated that the analytical SBFs are physically realistic, we develop a scheme for representing an arbitrary LPO as a superposition of the SBFs and for determining the evolution equations satisfied by the expansion coefficients. We illustrate the method both for simple uniform deformations (uniaxial compression, simple shear) and for more geophysically realistic nonuniform deformation histories.

  6. Influence of preferred orientation on the electrical conductivity of fluorine-doped tin oxide films.

    Science.gov (United States)

    Wang, Jian Tao; Shi, Xiang Lei; Liu, Wei Wei; Zhong, Xin Hua; Wang, Jian Nong; Pyrah, Leo; Sanderson, Kevin D; Ramsey, Philip M; Hirata, Masahiro; Tsuri, Keiko

    2014-01-14

    Current development of high-performance transparent conductive oxide (TCO) films is limited with tradeoff between carrier mobility and concentration since none of them can be improved without sacrificing the other. In this study, we prepare fluorine doped tin oxide (FTO) films by chemical vapor deposition with inclusions of different additives and report that the mobility can be varied from 0.65 to 28.5 cm(2) V(-1) s(-1) without reducing the achieved high carrier concentration of 4 × 10(20) cm(-3). Such an increase in mobility is shown to be clearly associated with the development of (200) preferred orientation (PO) but concurrent degradation of (110) PO in films. Thus, at a constant high carrier concentration, the electrical conductivity can be improved via carrier mobility simply by PO control. Such a one-step approach avoiding conventional post-deposition treatment is suggested for developing next-generation FTO as well as other TCO films with better than ever conductivities.

  7. Sexual Orientation, Drug Use Preference during Sex, and HIV Risk Practices and Preferences among Men Who Specifically Seek Unprotected Sex Partners via the Internet

    Directory of Open Access Journals (Sweden)

    Hugh Klein

    2009-05-01

    Full Text Available The present study entailed conducting a content analysis of 1,434 ads/profiles posted on one of the most popular “Men who have Sex with Men” (MSM websites that specifically fosters unprotected sex. Ads/profiles were selected randomly based on the American ZIP code of residence (n = 1,316, with a randomly-drawn oversampling of profiles of men who self-identified as heterosexual or ���curious” rather than gay or bisexual (n = 118. Data were collected between September 2006 and September 2007. The purpose of the present paper is to examine the conjoint effects of self-identified sexual orientation and preference for having/not having sex while high, on men’s sought-after sexual risk. Analytical comparisons of the four groups showed that, on most measures, the combination of sexual orientation and drug use preference during sex differentiated the men. Generally speaking, gay/bisexual men who advertised online for partners with whom they could have sex while high expressed the greatest interest in risky sexual behaviors (e.g., felching, unprotected oral sex, unprotected anal sex and various risk-related preferences (e.g., multiple partner sex, anonymous sex, eroticizing ejaculatory fluids. This is especially true when they are compared to their heterosexual/“curious” counterparts whose online profiles were not as likely to indicate a desire for having sex while high.

  8. Improving All-Inorganic Perovskite Photodetectors by Preferred Orientation and Plasmonic Effect.

    Science.gov (United States)

    Dong, Yuhui; Gu, Yu; Zou, Yousheng; Song, Jizhong; Xu, Leimeng; Li, Jianhai; Xue, Jie; Li, Xiaoming; Zeng, Haibo

    2016-10-01

    All-inorganic perovskites have high carrier mobility, long carrier diffusion length, excellent visible light absorption, and well overlapping with localized surface plasmon resonance (LSPR) of noble metal nanocrystals (NCs). The high-performance photodetectors can be constructed by means of the intrinsic outstanding photoelectric properties, especially plasma coupling. Here, for the first time, inorganic perovskite photodetectors are demonstrated with synergetic effect of preferred-orientation film and plasmonic with both high performance and solution process virtues, evidenced by 238% plasmonic enhancement factor and 10(6) on/off ratio. The CsPbBr3 and Au NC inks are assembled into high-quality films by centrifugal-casting and spin-coating, respectively, which lead to the low cost and solution-processed photodetectors. The remarkable near-field enhancement effect induced by the coupling between Au LSPR and CsPbBr3 photogenerated carriers is revealed by finite-difference time-domain simulations. The photodetector exhibits a light on/off ratio of more than 10(6) under 532 nm laser illumination of 4.65 mW cm(-2) . The photocurrent increases from 0.67 to 2.77 μA with centrifugal-casting. Moreover, the photocurrent rises from 245.6 to 831.1 μA with Au NCs plasma enhancement, leading to an enhancement factor of 238%, which is the most optimal report among the LSPR-enhanced photodetectors, to the best of our knowledge. The results of this study suggest that all-inorganic perovskites are promising semiconductors for high-performance solution-processed photodetectors, which can be further enhanced by Au plasmonic effect, and hence have huge potentials in optical communication, safety monitoring, and biological sensing.

  9. Constraints from Naturally Deformed Peridotites on Controls on Olivine Lattice Preferred Orientation

    Science.gov (United States)

    Bernard, R. E.; Behr, W. M.

    2016-12-01

    Seismic anisotropy in the upper mantle is produced primarily by lattice preferred orientations (LPO) in olivine formed during viscous deformation. Because seismic anisotropy is one of the principal means of characterizing upper mantle flow directions, it is critical to understand how LPO is affected by deformation conditions. Laboratory experiments suggest that water content and stress magnitude each play key roles in the development of LPO in olivine under experimental conditions, but it is unclear to what extent these results apply to natural conditions. We use peridotite xenoliths from a wide range of tectonic settings (Lunar Craters, Geronimo, and San Carlos volcanic fields in the Basin and Range; Cima and Deadman Lake volcanic fields in the Mojave; the Navajo Volcanic field in the Colorado Plateau; and the Potrillo volcanic field in the Rio Grande Rift region) to investigate correlations between water content, stress, and olivine LPO in natural rocks. Water contents were measured using Secondary Ion Mass Spectrometry, stress magnitudes using paleopiezometry, and LPOs using electron backscatter diffraction. The samples examined exhibit a range of fabric types, including A-, B-, C-, and E-type LPOs. Mojave xenoliths show no difference in water content between A- and E-type LPO; instead, differences in fabric type appear to reflect variations in strain magnitude. Samples from the Navajo volcanic field do show a correlation between water influx and stress magnitude as they exhibit abundant hydrous minerals and high water contents, stress magnitudes greater than 250 MPa and B-type olivine LPOs. Additional results from other xenolith suites will be presented at the meeting.

  10. Relationship between crystal growth mode, preferred orientation and magnetostriction of (Tb0.3Dy0.7)Fe1.95 alloys

    Institute of Scientific and Technical Information of China (English)

    ZHANG Shirong; LI Kuoshe; YU Dunbo; LI Yongsheng; YANG Hongchuan; LI Hongwei; TU Ganfeng

    2008-01-01

    The relationship between crystal growth mode, preferred orientation and magnetostrictive properties of (Tb0.3Dy0.7)Fe1.95 alloys was investigated at different directional solidification rates. The results showed that preferred orientation had a strong influence on the characteristics of (Tb0.3Dy0.7)Fe1.95 alloys. At lower solidification rates, the sample with preferred orientation showed larger low-field magnetostriction and apparent compressive stress effect. The excessive solidification rate resulted in failure of preferred orientation and a poor magnetostrictive performance. With an increase in solidification rates, the crystal growth modes changed gradually from cellular and primary dendrite morphology to developed dendritic morphology. In addition, domain configurations were observed using magnetic force microscopy, and the change of magnetostrictive properties was interpreted in terms of revealing the domain configurations.

  11. Highly conducting and preferred oriented boron doped nc-Si films for window layers in nc-Si solar cells

    Science.gov (United States)

    Mondal, Praloy; Das, Debajyoti

    2016-05-01

    Growth and optimization of the boron dopednanocrystalline silicon (nc-Si) films have been studied by varyingthe gaspressure applied to the hydrogendiluted silane plasma in RF (13.56 MHz) plasma-enhanced chemical vapor deposition (PECVD) system, using diborane (B2H6) as the dopant gas. High magnitudeof electrical conductivity (~102 S cm-1) andorientedcrystallographic lattice planes have been obtained with high crystalline volume fraction (~86 %) at an optimum pressure of 2.5 Torr. XRD and Raman studies reveal good crystallinity with preferred orientation, suitable for applications in stacked layer devices, particularly in nc-Si solar cells.

  12. Biological apatite (BAp) crystallographic orientation and texture as a new index for assessing the microstructure and function of bone regenerated by tissue engineering.

    Science.gov (United States)

    Nakano, Takayoshi; Kaibara, Kazuhiro; Ishimoto, Takuya; Tabata, Yasuhiko; Umakoshi, Yukichi

    2012-10-01

    Recently, there have been remarkable advances in medical techniques for regenerating bone defects. To determine the degree of bone regeneration, it is essential to develop a new method that can analyze microstructure and related mechanical function. Here, quantitative analysis of the orientation distribution of biological apatite (BAp) crystallites by a microbeam X-ray diffractometer system is proposed as a new index of bone quality for the evaluation of regenerated bone microstructure. Preferential alignment of the BAp c-axis in the rabbit ulna and skull bone, regenerated by controlled release of basic fibroblast growth factor (bFGF) was investigated. The BAp c-axis orientation was evaluated by the relative intensity between the (002) and (310) diffraction peaks, or the three-dimensional texture for the (002) peak. It was found that new bone in the defects was initially produced without preferential alignment of the BAp c-axis, and subsequently reproduced to recover towards the original alignment. In other words, the BAp density recovered prior to the BAp orientation. Perfect recovery of BAp alignment was not achieved in the ulna and skull defects after 4 weeks and 12 weeks, respectively. Apparent recovery of the macroscopic shape and bio-mineralization of BAp was almost complete in the ulna defect after 4 weeks. However, an additional 2 weeks was required for complete repair of BAp orientation. It is finally concluded that orientation distribution of BAp crystallites offers an effective means of evaluating the degree of microstructural regeneration, and also the related mechanical function, in regenerated hard tissues.

  13. On the colour of wing scales in butterflies: iridescence and preferred orientation of single gyroid photonic crystals

    Science.gov (United States)

    2017-01-01

    Lycaenid butterflies from the genera Callophrys, Cyanophrys and Thecla have evolved remarkable biophotonic gyroid nanostructures within their wing scales that have only recently been replicated by nanoscale additive manufacturing. These nanostructures selectively reflect parts of the visible spectrum to give their characteristic non-iridescent, matte-green appearance, despite a distinct blue–green–yellow iridescence predicted for individual crystals from theory. It has been hypothesized that the organism must achieve its uniform appearance by growing crystals with some restrictions on the possible distribution of orientations, yet preferential orientation observed in Callophrys rubi confirms that this distribution need not be uniform. By analysing scanning electron microscope and optical images of 912 crystals in three wing scales, we find no preference for their rotational alignment in the plane of the scales. However, crystal orientation normal to the scale was highly correlated to their colour at low (conical) angles of view and illumination. This correlation enabled the use of optical images, each containing up to 104–105 crystals, for concluding the preferential alignment seen along the at the level of single scales, appears ubiquitous. By contrast, orientations were found to occur at no greater rate than that expected by chance. Above a critical cone angle, all crystals reflected bright green light indicating the dominant light scattering is due to the predicted band gap along the direction, independent of the domain orientation. Together with the natural variation in scale and wing shapes, we can readily understand the detailed mechanism of uniform colour production and iridescence suppression in these butterflies. It appears that the combination of preferential alignment normal to the wing scale, and uniform distribution within the plane is a near optimal solution for homogenizing the angular distribution of the band gap relative to the wings. Finally

  14. Pulsed neutron spectroscopic imaging for crystallographic texture and microstructure

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Hirotaka, E-mail: hakuryu@eng.hokudai.ac.jp [Graduate School of Engineering, Hokkaido University, Kita-13 Nishi-8, Kita-ku, Sapporo 060-8628 (Japan); Kamiyama, Takashi [Graduate School of Engineering, Hokkaido University, Kita-13 Nishi-8, Kita-ku, Sapporo 060-8628 (Japan); Iwase, Kenji; Ishigaki, Toru [Frontier Research Center for Applied Atomic Sciences, Ibaraki University, Ibaraki 319-1106 (Japan); Kiyanagi, Yoshiaki [Graduate School of Engineering, Hokkaido University, Kita-13 Nishi-8, Kita-ku, Sapporo 060-8628 (Japan)

    2011-09-21

    A time-of-flight (TOF) spectroscopic neutron imaging at a pulsed neutron source is expected to be a new material analysis tool because this method can non-destructively investigate the spatial dependence of the crystallographic and metallographic information in a bulk material. For quantitative evaluation of such information, a spectral analysis code for the transmission data is necessary. Therefore, we have developed a Rietveld-like analysis code, RITS. Furthermore, we have applied the RITS code to evaluation of the position dependence of the crystal orientation anisotropy, the preferred orientation and the crystallite size of a welded {alpha}-iron plate, and we successfully obtained the information on the texture and the microstructure. However, the reliability of the values given by the RITS code has not been evaluated yet in detail. For this reason, we compared the parameters provided by the RITS code with the parameters obtained by the neutron TOF powder diffractometry and its Rietveld analysis. Both the RITS code and the Rietveld analysis software indicated values close to each other, but there were systematic differences on the preferred orientation and the crystallite size.

  15. Effect of oxygen on weld shape and crystallographic orientation of duplex stainless steel weld using advanced A-TIG (AA-TIG) welding method

    Energy Technology Data Exchange (ETDEWEB)

    Zou, Ying, E-mail: yingzou@jwri.osaka-u.ac.jp; Ueji, Rintaro; Fujii, Hidetoshi

    2014-05-01

    The double-shielded advanced A-TIG (AA-TIG) welding method was adopted in this study for the welding of the SUS329J4L duplex stainless steel with the shielding gases of different oxygen content levels. The oxygen content in the shielding gas was controlled by altering the oxygen content in the outer layer gas, while the inner layer remained pure argon to suppress oxidation on the tungsten electrode. As a result, a deep weld penetration was obtained due to the dissolution of oxygen into the weld metals. Additionally, the microstructure of the weld metal was changed by the dissolution of oxygen. The austenite phase at the ferrite grain boundary followed a Kurdjumov–Sachs (K–S) orientation relationship with the ferrite matrix phase at any oxide content. On the other hand, the orientation relationship between the intragranular austenite phase and the ferrite matrix phase exhibited different patterns under different oxygen content levels. When there was little oxide in the fusion zone, only a limited part of the intragranular austenite phase and the ferrite matrix phase followed the K–S orientation relationship. With the increase of the oxide, the correspondence of the K–S relationship increased and fit very well in the 2.5% O{sub 2} shielded sample. The investigation of this phenomenon was carried out along with the nucleation mechanisms of the intragranular austenite phases. - Highlights: • Weld penetration increased with the increase of the oxygen content. • Average diameter and number density of oxide were changed by the oxygen content. • K-S relationship of Widmanstätten austenite/ferrite wasn’t varied by oxide. • Orientation relationship of intragranular austenite/ferrite was varied by oxide.

  16. Slip patterns and preferred dislocation boundary planes

    DEFF Research Database (Denmark)

    Winther, G.

    2003-01-01

    The planes of deformation induced extended planar dislocation boundaries are analysed in two different co-ordinate systems, namely the macroscopic system defined by the deformation axes and the crystallographic system given by the crystallographic lattice. The analysis covers single and polycryst......The planes of deformation induced extended planar dislocation boundaries are analysed in two different co-ordinate systems, namely the macroscopic system defined by the deformation axes and the crystallographic system given by the crystallographic lattice. The analysis covers single...... and polycrystals of fcc metals in three deformation modes (rolling, tension and torsion). In the macroscopic system, boundaries lie close to the macroscopically most stressed planes. In the crystallographic system, the boundary plane depends on the grain/crystal orientation. The boundary planes in both co......-ordinate systems are rationalised based on the slip. The more the slip is concentrated on a slip plane, the closer the boundaries lie to this. The macroscopic preference arises from the macroscopic directionality of the slip. The established relations are applied to (a) prediction of boundary planes from slip...

  17. An electron-accepting molecular unit exhibiting an orientational preference favorable for organic photovoltaic applications

    Energy Technology Data Exchange (ETDEWEB)

    Akaike, Kouki, E-mail: kakaike@physik.hu-berlin.de [RIKEN Advanced Science Institute, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Ando, Shinji; Enozawa, Hideo [RIKEN Advanced Science Institute, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Kosaka, Atsuko; Kajitani, Takashi [RIKEN Advanced Science Institute, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Chemical Resources Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama, Kanagawa 226-8503 (Japan); Fukushima, Takanori, E-mail: fukushima@res.titech.ac.jp [RIKEN Advanced Science Institute, 2-1 Hirosawa, Wako, Saitama 351-0198 (Japan); Chemical Resources Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama, Kanagawa 226-8503 (Japan)

    2015-05-29

    Control of molecular orientation of organic semiconductor is essential for efficient light absorption and charge-carrier transport in organic optoelectronic devices. We synthesized compound 1 as a fundamental electron-accepting building block for the design of n-type semiconductors and conducting polymers. We found that this molecule, upon evaporation onto a substrate such as SiO{sub 2} and electron-donor films, spontaneously assembles with a face-on orientation relative to the substrate surface. This orientation is favorable for thin-film organic photovoltaics. Despite relatively small π-conjugation, 1 showed strong absorption in visible-light region and an appropriate lowest unoccupied molecular orbital energy for electron transfer with electron donors including copper phthalocyanine and poly(3-hexylthiophene). Accordingly, thin-film devices, fabricated using 1 and electron donors, exhibited a clear photovoltaic response. This suggests that compound 1 provides a promising building block for the development of active materials in organic photovoltaics. - Highlights: • An electron acceptor (1) featuring an indacenetetraone core was designed. • Acceptor 1 exhibits strong electronic absorption in visible-light region. • Acceptor 1 spontaneously adopts face-on orientation on SiO{sub 2} and organic substrates. • Thin film of 1 shows an n-type semiconducting property. • Electron donor/1 bilayer films display a clear photovoltaic response.

  18. Prospective Teachers' Value Orientations as Determinants of Preference for External and Anonymous Whistleblowing

    Science.gov (United States)

    Gokce, Asiye Toker

    2013-01-01

    Whistle-blowing indicates disclosing organizational wrongdoings resulting in harm to third parties. An individual's decision to blow the whistle might be based upon organizational, situational or personal factors. This study inquires the relationship between value orientations of prospective teachers and choices for whistle-blowing with particular…

  19. Vote Choice, Ideology, and Social Dominance Orientation Influence Preferences for Lower Pitched Voices in Political Candidates

    DEFF Research Database (Denmark)

    Laustsen, Lasse; Petersen, Michael Bang; A. Klofstad, Casey

    2015-01-01

    Humans are equipped with a psychological system of followership that evolved to regulate choices of leaders based partly on would-be leaders’ physiological features. One such feature is voice pitch, which is determined by the physiology of the throat. Recent studies find that political candidates...... in modern elections with lower-pitched voices are generally more successful. As lower-pitched voices are perceived as stronger and more dominant, these findings have been taken to indicate a general preference for dispositional abilities in leaders to protect and prevail in conflicts. Here we extend upon...... these findings by demonstrating that conservatives and Republicans tend to view the world as much more competitive and threatening than liberals and Democrats. We utilize two existing data sources to show that political candidates with lower-pitched voices are preferred more among conservative Republicans than...

  20. Crystallographic texturing in Nb3Sn multifilamentary superconducting composites

    Science.gov (United States)

    Cogan, Stuart F.; Rose, Robert M.

    1980-03-01

    Crystallographic texturing in Nb3Sn composites, fabricated by both the external diffusion and the commercial bronze processes, has been investigated. In the external-diffusion-processed composite the as-drawn texture of the copper matrix contained ca. 55% and 45% ; after recrystallization at 650 °C for 16 h this changed to 70% and 30% . Tin plating and reaction heat treatment for 40 h at 650 °C eliminated most of the texturing. In a commercial bronze-processed composite a or texture was obtained in the as-drawn bronze matrix, and after a reaction heat treatment at 700 °C for 30 h a diffuse texture was developed. In both composites the Nb3Sn reaction layer exhibited no preferred orientation.

  1. Optical band gap demarcation around 2.15 eV depending on preferred orientation growth in red HgI{sub 2} films

    Energy Technology Data Exchange (ETDEWEB)

    Tyagi, Pankaj, E-mail: pankajtyagicicdu@gmail.com

    2017-04-01

    Thermally evaporated stoichiometric films of red HgI{sub 2} show preferred orientation growth with either (102) or (002) orientation. The as grown films shows a change from one preferred orientation to another depending on their thickness, open-air heat-treatment and in-situ heat treatment of films. The in-situ heat-treatment of thermally evaporated stoichiometric films of red HgI{sub 2} with preferred growth of (102) orientation shows a gradual linear decrease in film thickness with in-situ heat-treatment temperature. On in-situ heat-treatment above 80 °C, it is found that HgI{sub 2} films become thinner than 900 nm, which are otherwise difficult to grow due to high vapor pressure of HgI{sub 2}. For these films the preferred orientation also changed from (102) to (002). The optical band gap (E{sub g}) also found to increase linearly with in-situ heat-treatment temperature. It is interesting to note that in-situ heat-treated films having (002) orientation had higher values of optical band gap than (102) orientation films. On combining these results with those of as grown and open-air heat-treated red HgI{sub 2} films reported in the literature, it is evident that there exists an optical band gap demarcation around 2.15 eV for red HgI{sub 2} thin films depending on their preferred orientation growth. Films with (102) orientation are found to have optical band gap less than 2.15 eV and those with (002) orientation are found to have optical band gap more than 2.15 eV. This is irrespective of the physical mean of obtaining the preferred orientation. The preferred orientation can be achieved by either physical means such as growing films with higher thickness, heat-treating them for short duration in open air or heat-treating them in-situ.

  2. The preferred orientation of Mn3 spins in magnetic multiferroic CaMn{sub 7}O{sub 12}

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Jian-Qing, E-mail: djqkust@sina.com; Zhang, Hu; Song, Yu-Min

    2015-12-15

    The remarkable ferroelectricity in CaMn{sub 7}O{sub 12} originates from the helicoidal spin spiral, in which the Mn3 (3b Wyckoff position) spin direction remains controversial. In this paper, the total energy, phase transition path, and spontaneous polarization of CaMn{sub 7}O{sub 12} are investigated by using first-principle methods. We show that, in order to account for the giant electric polarization and the correct phase transition sequence, the relative orientation between the spins of Mn3 and Mn2 (9d Wyckoff position) sites with the same coordinate along the hexagonal c-axis can not be antiparallel, i.e. their relative orientation angle should be ϕ≈0.84π instead of ϕ=π. The most likely reason for the observation of ϕ=π can be attributed to the withdrawal of spin–orbital coupling between the Mn2 and Mn3 spins, which is caused by doping Cu{sup 2+} in the samples for neutron powder diffraction measurements. - Highlights: • In CaMn{sub 7}O{sub 12}, the preferred orientation angle of the Mn3 spins remains controversial. • The relative orientation angle between Mn3 and Mn2 spins should be 0.84π instead of π. • For ϕ=π, phase transition path and polarization are inconsistent with experiments. • The reason for observation of ϕ=π is due to Cu{sup 2+}-doping in the experimental samples.

  3. The preferred orientation of Mn3 spins in magnetic multiferroic CaMn7O12

    Science.gov (United States)

    Dai, Jian-Qing; Zhang, Hu; Song, Yu-Min

    2015-12-01

    The remarkable ferroelectricity in CaMn7O12 originates from the helicoidal spin spiral, in which the Mn3 (3b Wyckoff position) spin direction remains controversial. In this paper, the total energy, phase transition path, and spontaneous polarization of CaMn7O12 are investigated by using first-principle methods. We show that, in order to account for the giant electric polarization and the correct phase transition sequence, the relative orientation between the spins of Mn3 and Mn2 (9d Wyckoff position) sites with the same coordinate along the hexagonal c-axis can not be antiparallel, i.e. their relative orientation angle should be ϕ≈0.84π instead of ϕ=π. The most likely reason for the observation of ϕ=π can be attributed to the withdrawal of spin-orbital coupling between the Mn2 and Mn3 spins, which is caused by doping Cu2+ in the samples for neutron powder diffraction measurements.

  4. Melt-preferred orientation, anisotropic permeability, and melt-band formation in a deforming, partially molten aggregate

    CERN Document Server

    Taylor-West, Jesse

    2015-01-01

    Shear deformation of partially molten rock in laboratory experiments causes the emergence of melt-enriched sheets (bands in cross-section) that are aligned at about 15-20 degrees to the shear plane. Deformation and deviatoric stress also cause the coherent alignment of pores at the grain scale. This leads to a melt-preferred orientation which may give rise to an anisotropic permeability. Here we develop a simple, general model of anisotropic permeability in partially molten rocks. We use linearised analysis and nonlinear numerical solutions to investigate its behaviour under simple shear deformation. In particular, we consider implications of the model for the emergence and angle of melt-rich bands. Anisotropic permeability affects the angle of bands and, in a certain parameter regime, it can give rise to low angles consistent with experiments. However, the conditions required for this regime have a narrow range and are unlikely to be met by experiments. Although anisotropic permeability may shape the behavio...

  5. Effect of partial covering of the visitor viewing area window on positioning and orientation of zoo orangutans: A preference test.

    Science.gov (United States)

    Bloomfield, Rachel C; Gillespie, Graeme R; Kerswell, Keven J; Butler, Kym L; Hemsworth, Paul H

    2015-01-01

    The window of the visitor viewing area adjacent to an animal platform in an orangutan enclosure was altered to produce three viewing treatments in a randomized controlled experiment. These treatments were window uncovered, left side of the window covered or right side of the window covered. Observations were conducted on the orangutans present on the platform, and on their location (left or right side), and orientation (towards or away from the window) while on the platform. The partial covering of the window had little effect on the proportion of time orangutans spent on the viewing platform, or on the direction they faced when on the platform. When the orangutans were facing towards the window, and the right side was uncovered, irrespective of whether the left side was covered, they spent about three quarters of the time on the right side, suggesting a preference for the right side of the platform. However, when the right side was covered and the left side uncovered, the animals facing towards the window spent only about a quarter of the time on the right side, that is, they spent more time on the uncovered side. The results suggest that the orangutans have a preference to position themselves to face the window of the visitor viewing area.

  6. Binding Preferences, Surface Attachment, Diffusivity, and Orientation of a Family 1 Carbohydrate-Binding Module on Cellulose

    Energy Technology Data Exchange (ETDEWEB)

    Nimlos, M. R.; Beckham, G. T.; Matthews, J. F.; Bu, L.; Himmel, M. E.; Crowley, M. F.

    2012-06-08

    Cellulase enzymes often contain carbohydrate-binding modules (CBMs) for binding to cellulose. The mechanisms by which CBMs recognize specific surfaces of cellulose and aid in deconstruction are essential to understand cellulase action. The Family 1 CBM from the Trichoderma reesei Family 7 cellobiohydrolase, Cel7A, is known to selectively bind to hydrophobic surfaces of native cellulose. It is most commonly suggested that three aromatic residues identify the planar binding face of this CBM, but several recent studies have challenged this hypothesis. Here, we use molecular simulation to study the CBM binding orientation and affinity on hydrophilic and hydrophobic cellulose surfaces. Roughly 43 {mu}s of molecular dynamics simulations were conducted, which enables statistically significant observations. We quantify the fractions of the CBMs that detach from crystal surfaces or diffuse to other surfaces, the diffusivity along the hydrophobic surface, and the overall orientation of the CBM on both hydrophobic and hydrophilic faces. The simulations demonstrate that there is a thermodynamic driving force for the Cel7A CBM to bind preferentially to the hydrophobic surface of cellulose relative to hydrophilic surfaces. In addition, the simulations demonstrate that the CBM can diffuse from hydrophilic surfaces to the hydrophobic surface, whereas the reverse transition is not observed. Lastly, our simulations suggest that the flat faces of Family 1 CBMs are the preferred binding surfaces. These results enhance our understanding of how Family 1 CBMs interact with and recognize specific cellulose surfaces and provide insights into the initial events of cellulase adsorption and diffusion on cellulose.

  7. Is J enough? Comparison of gravitational waves emitted along the total angular momentum direction with other preferred orientations

    CERN Document Server

    O'Shaughnessy, R; London, L; Meeks, Z; Shoemaker, D

    2012-01-01

    The gravitational wave signature emitted from a merging binary depends on the orientation of an observer relative to the binary. Previous studies suggest that emission along the total initial or total final angular momenta leads to both the strongest and simplest signal from a precessing compact binary. In this paper we describe a concrete counterexample: a binary with $m_1/m_2=4$, $a_1=0.6 \\hat{x} = -a_2$, placed in orbit in the x,y plane. We extract the gravitational wave emission along several proposed emission directions, including the initial (Newtonian) orbital angular momentum; the final (~ initial) total angular momentum; and the dominant principal axis of $_M$. Using several diagnostics, we show that the suggested preferred directions are not representative. For example, only for a handful of other directions (0.95). We conclude that the information available in just one direction (or mode) does not adequately encode the complexity of orientation-dependent emission for even short signals from merging...

  8. Fabrication and Characterization of p-Type SnO Thin Film with High c-Axis Preferred Orientation

    Science.gov (United States)

    Pei, Yanli; Liu, Wuguang; Shi, Jingtao; Chen, Zimin; Wang, Gang

    2016-11-01

    p-Type tin monoxide (SnO) thin films with high c-axis preferred orientation have been fabricated on quartz substrate via electron-beam evaporation at 280°C. Subsequently, rapid thermal annealing (RTA) was performed in N2 atmosphere at 400°C to 800°C. Their structural, chemical, optical, and electrical properties were investigated by x-ray diffraction analysis, ultraviolet-visible spectroscopy, scanning electron microscopy, x-ray photoelectron spectroscopy, and Hall-effect measurements. The c-axis-oriented films of Sn-rich SnO presented excellent thermal stability up to RTA at 700°C. Both the crystallization and the hole Hall mobility were enhanced with increasing RTA temperature, with Hall mobility of 16 cm2 V-1 s-1 being obtained after RTA at 700°C. It was considered that the presence of defects and low scattering from grain boundaries contributed to this high Hall mobility. RTA annealing temperature above 700°C induced chemical reaction between SnO and the quartz substrate, with a change of the film to amorphous state with Sn4+ formation.

  9. Effects of interfaces and preferred orientation on the electrical response of composites of alumina and silicon carbide whiskers

    Science.gov (United States)

    Bertram, Brian D.

    Ceramic-matrix composites of alumina and silicon carbide whiskers have recently found novel commercial application as electromagnetic absorbers. However, a detailed understanding of how materials issues influence the composite electrical response which underpins this application has been absent until now. In this project, such composites were electrically measured over a wide range of conditions and modeled in terms of various aspects of the microstructure in order to understand how they work. For this purpose, three types of composites were made by different methods from the same set of ceramic powder blends loaded with different volume fractions of whiskers. In doing so, the interfaces between whiskers, the preferred orientations of whiskers, and the structure of electrically-connected whisker clusters were varied. In Chapter 3, it shown that Schottky energy barriers form at the junctions of the wide-bandgap semiconductor whiskers when metal electrodes are applied for measurements. These barriers were characterized on the microscopic and macroscopic level, and the gap between these different scales was bridged. Also, a modeling approach was developed for the loading dependence of the composite non-linear response which results from the barriers. In Chapter 4, the effects of significantly different types of preferred orientation are elucidated and a strong structure-property correlation is established. The effects of other structural issues on the electrical response are uncovered as well, such as those pertaining to porosity in the ceramic and the interfaces between electrically-connected SiCw. In Chapter 5, the non-linear response model of Chapter 3 is adapted in the development of a new model for electrically-percolated clusters. This model demonstrates how loading and interfacial issues influence the cluster topology and may result in the cluster having a non-linear electrical response. In Chapter 6, the effects of various factors on the broadband frequency

  10. Quantification of preferred orientation in graphite electrodes for Li-ion batteries with a novel X-ray-diffraction-based method

    Science.gov (United States)

    Malifarge, Simon; Delobel, Bruno; Delacourt, Charles

    2017-03-01

    To answer the demand of increased autonomy in transportation applications, the energy density of battery electrode need to be enhanced. The porous electrode microstructure needs to be controlled to optimize battery performance and prevent electrode degradation (e.g., Li plating). Graphite negative electrodes generally consist of anisotropic particles that exhibit a preferred orientation. Graphite particles tend to stack perpendicular to ionic pathways which results in transport issues and reduces overall battery power capability. In this context, a method based on X-ray diffraction is described to quantify the preferred orientation of graphite particles in actual electrodes. A step orientation-distribution function is used to describe the pole-density profile of the diffracting graphite crystallites. A fraction of graphite particles oriented parallel to the electrode current collector within a tilt tolerance is derived from the step function. An application of this method is presented on a set of graphite electrodes that underwent different calendering conditions.

  11. Crystallographic Information Resources

    Science.gov (United States)

    Glasser, Leslie

    2016-01-01

    Crystallographic information provides the fundamental basis for understanding the properties and behavior of materials. This data, such as chemical composition, unit cell dimensions, space group, and atomic positions, derives from the primary literature--that is, from published experimental measurement or theoretical calculation. Although the…

  12. Crystallographic Behavior of Iron Oxide Minerals in the Deformed Iron Formation of Quadrilátero Ferrífero

    Science.gov (United States)

    Duarte Lisboa, Filipe Augusto; Lagoeiro, Leonardo; Martins Graça, Leonardo; Ávila, Carlos Fernando; Ferreira Barbosa, Paola

    2016-04-01

    The Quadrilátero Ferrífero (QF) which is located in Brazil represents a mineral province of great importance for hosting Banded Iron Formation deposits (BIFs). The Alegria mine which belongs to Vale Company is located in the east part of Quadrilátero Ferrífero and it explores iron ore from a region of great structural complexity. A deformed BIF sample that presents a micro-fold on quartz and hematite bands was analyzed through Electron Backscatter Diffraction technique (EBSD) in order to relate the crystallographic orientations with the microstructures along the micro-fold envelop. For the sample orientation the Z-axis is taken parallel to the fold limb, Y-axis is perpendicular to the fold hinge and X-axis perpendicular to the YZ plane. In the limbs hematite grains are mostly stretched whereas at the hinge grains tend to be somewhat equant. On the other hand, quartz grain shapes are invariable along the fold, with a few exceptions in the hinge where grains are slightly elongated. Grains of hematite present a strong c-axis ({0001}) preferred orientation forming a subtle girdle somewhat parallel to the XY plane of the strain ellipsoid determined macroscopically (XY being the foliation plane), and a strong () crystallographic fabric approximately parallel to the Z-axis. Similarly, the poles to the prismatic planes ({m} or {10bar10}) also have a stronger crystallographic fabric parallel to the Z axis. It seems that there are two crossing planes for the orientation of and {m} with the two maxima at the intersection of the two planes. Typical hematite crystallographic fabrics are somewhat distinct, since {c} axis commonly forms a very strong fiber texture parallel to the pole of the foliation. Most studies regard such crystallographic texture as evidence for high activity of {c} slip. The {c} girdles observed here are common for mica grains under rigid body rotation in constriction strain, which mechanism is commonly observed in the hematite grains of the sample. The

  13. Electronic structure and its external electric field modulation of PbPdO2 ultrathin slabs with (002) and (211) preferred orientations.

    Science.gov (United States)

    Yang, Yanmin; Zhong, Kehua; Xu, Guigui; Zhang, Jian-Min; Huang, Zhigao

    2017-07-31

    The Electronic structure of PbPdO2 with (002) and (211) preferred orientations were investigated using first-principles calculation. The calculated results indicate that, (002) and (211) orientations exhibit different electric field dependence of band-gap and carrier concentration. The small band gap and more sensitive electric field modulation of band gap were found in (002) orientation. Moreover, the electric field modulation of the resistivity up to 3-4 orders of magnitude is also observed in (002) slab, which reveals that origin of colossal electroresistance. Lastly, electric field modulation of band gap is well explained. This work should be significant for repeating the colossal electroresistance.

  14. Crystallographic orientations and twinning of electrodeposited nickel

    DEFF Research Database (Denmark)

    Alimadadi, Hossein; da Silva Fanta, Alice Bastos; Somers, Marcel A. J.;

    2014-01-01

    A series of nickel layers was electrodeposited at different current densities from a Watts type electrolyte containing the additive 2-butyne-1,4-diol in various concentrations. The internal structure of the nickel electrodeposits was systematically investigated applying complementary microscopic...

  15. Preferred orientation of nanoscale order at the surface of amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} films

    Energy Technology Data Exchange (ETDEWEB)

    Tony Li, Tian; Abelson, John R. [Department of Materials Science and Engineering, University of Illinois at Urbana-Champaign, 1304 W. Green St., Urbana, Illinois 61801 (United States); Coordinated Science Laboratory, University of Illinois at Urbana-Champaign, 1308 W. Main St., Urbana, Illinois 61801 (United States); Hoon Lee, Tae; Elliott, Stephen R. [Department of Chemistry, University of Cambridge, Lensfield Road, Cambridge CB2 1EW (United Kingdom)

    2013-11-11

    We report evidence that as-deposited amorphous Ge{sub 2}Sb{sub 2}Te{sub 5} thin films contain nanoscale clusters that exhibit a preferred orientation, attributed to the earliest stages of heterogeneous nucleation. Fluctuation transmission electron microscopy reveals structural order in the samples, but (220)-related contributions are suppressed. When homogeneous nucleation is promoted via electron bombardment, the sample remains diffraction amorphous but the (220) contribution appears. We simulated data for randomly oriented nanoscale order using ab initio molecular-dynamics models of Ge{sub 2}Sb{sub 2}Te{sub 5}. The simulated (220) contribution always has larger magnitude than higher-order signals; thus, the lack of the experimental signal indicates a significant preferred orientation.

  16. Crystallographic effects during micromachining — A finite-element model

    Science.gov (United States)

    Song, Shin-Hyung; Choi, Woo Chun

    2015-07-01

    Mechanical micromachining is a powerful and effective way for manufacturing small sized machine parts. Even though the micromachining process is similar to the traditional machining, the material behavior during the process is much different. In particular, many researchers report that the basic mechanics of the work material is affected by microstructures and their crystallographic orientations. For example, crystallographic orientations of the work material have significant influence on force response, chip formation and surface finish. In order to thoroughly understand the effect of crystallographic orientations on the micromachining process, finite-element model (FEM) simulating orthogonal cutting process of single crystallographic material was presented. For modeling the work material, rate sensitive single crystal plasticity of face-centered cubic (FCC) crystal was implemented. For the chip formation during the simulation, element deletion technique was used. The simulation model is developed using ABAQUS/explicit with user material subroutine via user material subroutine (VUMAT). Simulations showed that variation of the specific cutting energy at different crystallographic orientations of work material shows significant anisotropy. The developed FEM model can be a useful prediction tool of micromachining of crystalline materials.

  17. Macromolecular crystallographic estructure refinement

    Directory of Open Access Journals (Sweden)

    Afonine, Pavel V.

    2015-04-01

    Full Text Available Model refinement is a key step in crystallographic structure determination that ensures final atomic structure of macromolecule represents measured diffraction data as good as possible. Several decades have been put into developing methods and computational tools to streamline this step. In this manuscript we provide a brief overview of major milestones of crystallographic computing and methods development pertinent to structure refinement.El refinamiento es un paso clave en el proceso de determinación de una estructura cristalográfica al garantizar que la estructura atómica de la macromolécula final represente de la mejor manera posible los datos de difracción. Han hecho falta varias décadas para poder desarrollar nuevos métodos y herramientas computacionales dirigidas a dinamizar esta etapa. En este artículo ofrecemos un breve resumen de los principales hitos en la computación cristalográfica y de los nuevos métodos relevantes para el refinamiento de estructuras.

  18. Piezoelectric Properties of Bismuth Layer-Structured Ferroelectric Ceramics with a Preferred Orientation Processed by the Reactive Templated Grain Growth Method

    Science.gov (United States)

    Takeuchi, Tsuguto; Tani, Toshihiko; Saito, Yasuyoshi

    1999-09-01

    Dense CaBi4Ti4O15 (CBT) and Na0.475Ca0.05Bi4.475Ti4O15 (NCBT) ceramics with a highly preferred {001} orientation were prepared by the reactive templated grain growth (RTGG) method. Plate-like Bi4Ti3O12 (BIT) particles were synthesized by a molten salt technique and used as the reactive template. The template particles were mixed with other oxide and carbonate powders and aligned by tape-casting. During the sintering, oriented CBT and NCBT were formed in situ topotaxially on the oriented BIT particles, and textured CBT and NCBT ceramics were eventually fabricated by the templated grain growth and densification. The Lotgering {001} orientation degree of the textured ceramics exceeded 90% for secondary-laminate sintered specimens. Textured CBT and NCBT ceramics poled in the perpendicular direction to the preferred axis exhibited electromechanical coupling coefficient (k33) and piezoelectric coefficients (d33 and g33) three times higher than the values for nontextured ceramics with the same composition.

  19. Effects of crystal preferred orientation on upper-mantle flow near plate boundaries: rheologic feedbacks and seismic anisotropy

    Science.gov (United States)

    Blackman, D. K.; Boyce, D. E.; Castelnau, O.; Dawson, P. R.; Laske, G.

    2017-09-01

    Insight into upper-mantle processes can be gained by linking flow-induced mineral alignment to regional deformation and seismic anisotropy patterns. Through a series of linked micro-macro scale numerical experiments, we explore the rheologic effects of crystal preferred orientation (CPO) and evaluate the magnitude of possible impacts on the pattern of flow and associated seismic signals for mantle that includes a cooling, thickening young oceanic lithosphere. The CPO and associated anisotropic rheology, computed by a micromechanical polycrystal model, are coupled with a large scale flow model (Eulerian Finite Element method) via a local viscosity tensor field, which quantifies the stress:strain rate response of a textured polycrystal. CPO is computed along streamlines throughout the model space and the corresponding viscosity tensor field at each element defines the local properties for the next iteration of the flow field. Stable flow and CPO distributions were obtained after several iterations for the two dislocation glide cases tested: linear and nonlinear stress:strain rate polycrystal behaviour. The textured olivine polycrystals are found to have anisotropic viscosity tensors in a significant portion of the model space. This directional dependence in strength impacts the pattern of upper-mantle flow. For background asthenosphere viscosity of ˜1020 Pa s and a rigid lithosphere, the modification of the corner flow pattern is not drastic but the change could have geologic implications. Feedback in the development of CPO occurs, particularly in the region immediately below the base of the lithosphere. Stronger fabric is predicted below the flanks of a spreading centre for fully coupled, power-law polycrystals than was determined using prior linear, intermediate coupling polycrystal models. The predicted SKS splitting is modestly different (˜0.5 s) between the intermediate and fully coupled cases for oceanic plates less than 20 Myr old. The magnitude of azimuthal

  20. Natural Examples of Olivine Lattice Preferred Orientation Patterns With a Flow-Normal a-Axis Maximum

    Science.gov (United States)

    Mizukami, T.; Wallis, S.; Yamamoto, J.

    2004-12-01

    Olivine lattice preferred orientation (LPO) due to ductile deformation is one of the main causes of mechanical anisotropy in the upper mantle and the patterns are useful to infer the direction of mantle flow from the seismic anisotropy in various settings. In subduction zones the mantle anisotropy near subduction boundaries suggests that olivine a-axes are arranged roughly perpendicular to plate motion. This anisotropy has been attributed to localized subduction-normal flow, applying a common type of olivine LPO with a `flow-parallel' a-axis maximum to the mantle. However, a recent deformational experiment provides an alternative interpretation that the B-type LPO with a `flow-normal' a-axis maximum can be developed in water-rich mantle above subducting slab. We document the widespread occurrence of B-type LPO in the Higashi-akaishi peridotite body, SW Japan, and examine the physical conditions in which it was formed. Our structural studies define four deformational phases in the Higashi-akaishi body (D1-D4) that are related to the tectonic evolution in the Cretaceous subduction zone at the Eurasian margin. The main deformational stage, D2, is associated with dynamic recrystallization of olivine to form porphyroclastic microstructure consisting of clear olivine neoblasts and porphyroclasts with abundant micro-inclusions. Parallel alginment of olivine neoblasts defines a stretching lineation (L2) and tectonic foliation (S2) and the D2 olivine LPO is identified as the B-type fabric with a-axes normal to L2, b-axes normal to S2 and c-axes parallel to L2. Micro-Raman spectroscopic analyses reveal that the syn-D2 micro-inclusions include hydrous minerals such as serpentine, indicating water-rich conditions for the D2 deformation. Garnet-orthopyroxene geothermobarometry applied to the D2 garnet peridotite reveals that the D2 stage was associated with the almost isothermal burial (700-800C, 2-3GPa). These D2 physical conditions in which the B-type LPO was formed are

  1. Phaser crystallographic software.

    Science.gov (United States)

    McCoy, Airlie J; Grosse-Kunstleve, Ralf W; Adams, Paul D; Winn, Martyn D; Storoni, Laurent C; Read, Randy J

    2007-08-01

    Phaser is a program for phasing macromolecular crystal structures by both molecular replacement and experimental phasing methods. The novel phasing algorithms implemented in Phaser have been developed using maximum likelihood and multivariate statistics. For molecular replacement, the new algorithms have proved to be significantly better than traditional methods in discriminating correct solutions from noise, and for single-wavelength anomalous dispersion experimental phasing, the new algorithms, which account for correlations between F(+) and F(-), give better phases (lower mean phase error with respect to the phases given by the refined structure) than those that use mean F and anomalous differences DeltaF. One of the design concepts of Phaser was that it be capable of a high degree of automation. To this end, Phaser (written in C++) can be called directly from Python, although it can also be called using traditional CCP4 keyword-style input. Phaser is a platform for future development of improved phasing methods and their release, including source code, to the crystallographic community.

  2. Impact of cooling condition on the crystal structure and surface quality of preferred c-axis-oriented AIN films for SAW devices

    Institute of Scientific and Technical Information of China (English)

    ZHANG Geng-yu; YANG Bao-he; ZHAO Jian; LI Cui-ping; LI Ming-ji

    2011-01-01

    AIN films with preferred c-axis orientation are deposited on Si substrates using the radio frequency (RF) magnetron sputtering method. The post-processing is carried out under the cooling conditions including high vacuum, low vacuum under deposition gas ambient and low vacuum under dynamic N2 ambient. Structures and morphologies of the films are analyzed by X-ray diffraction (XRD) and atomic force microscopy (AFM). The hardness and Young's modulus are investigated by the nanoindenter. The experimental results indicate that the (100) and (110) peak intensities decrease in the XRD spectra and the root-mean-square of roughness (Rrms) of the film decreases gradually with the increase of the cooling rate. The maximum values of the hardness and Young's modulus are obtained by cooling in low vacuum under deposition gas ambient. The reason for orientation variation of the films is explained from the perspective of the Al-N bond formation.

  3. Crystallographic Mapping of Guided Nanowires by Second Harmonic Generation Polarimetry.

    Science.gov (United States)

    Neeman, Lior; Ben-Zvi, Regev; Rechav, Katya; Popovitz-Biro, Ronit; Oron, Dan; Joselevich, Ernesto

    2017-02-08

    The growth of horizontal nanowires (NWs) guided by epitaxial and graphoepitaxial relations with the substrate is becoming increasingly attractive owing to the possibility of controlling their position, direction, and crystallographic orientation. In guided NWs, as opposed to the extensively characterized vertically grown NWs, there is an increasing need for understanding the relation between structure and properties, specifically the role of the epitaxial relation with the substrate. Furthermore, the uniformity of crystallographic orientation along guided NWs and over the substrate has yet to be checked. Here we perform highly sensitive second harmonic generation (SHG) polarimetry of polar and nonpolar guided ZnO NWs grown on R-plane and M-plane sapphire. We optically map large areas on the substrate in a nondestructive way and find that the crystallographic orientations of the guided NWs are highly selective and specific for each growth direction with respect to the substrate lattice. In addition, we perform SHG polarimetry along individual NWs and find that the crystallographic orientation is preserved along the NW in both polar and nonpolar NWs. While polar NWs show highly uniform SHG along their axis, nonpolar NWs show a significant change in the local nonlinear susceptibility along a few micrometers, reflected in a reduction of 40% in the ratio of the SHG along different crystal axes. We suggest that these differences may be related to strain accumulation along the nonpolar wires. We find SHG polarimetry to be a powerful tool to study both selectivity and uniformity of crystallographic orientations of guided NWs with different epitaxial relations.

  4. Fourier descriptors analysis of anisotropy and preferred Orientation in geological samples; Analisis de la anisotropia y la orientacion preferente en materiales geologicos mediante el Metodo de Descriptoes de Fourier

    Energy Technology Data Exchange (ETDEWEB)

    Santiago Buey, C. de

    2011-07-01

    This study focuses on the use of Fourier descriptors to evaluate and quantify two specific fabric characteristics of geological materials: anisotropy of particles or voids morphologies and particle orientation. To this end, a theoretical section of a rock was created, made of ellipses and rectangles of different axes ratios and different orientations. The Fourier descriptors method was applied to calculate the anisotropy and orientation of each particle and, finally, a rose diagram was constructed to represent the particles orientations distribution and to observe the presence or not of any preferred orientation. (Author) 15 refs.

  5. Alcohol-Preferring Rats Show Goal Oriented Behaviour to Food Incentives but Are Neither Sign-Trackers Nor Impulsive.

    Directory of Open Access Journals (Sweden)

    Yolanda Peña-Oliver

    Full Text Available Drug addiction is often associated with impulsivity and altered behavioural responses to both primary and conditioned rewards. Here we investigated whether selectively bred alcohol-preferring (P and alcohol-nonpreferring (NP rats show differential levels of impulsivity and conditioned behavioural responses to food incentives. P and NP rats were assessed for impulsivity in the 5-choice serial reaction time task (5-CSRTT, a widely used translational task in humans and other animals, as well as Pavlovian conditioned approach to measure sign- and goal-tracking behaviour. Drug-naïve P and NP rats showed similar levels of impulsivity on the 5-CSRTT, assessed by the number of premature, anticipatory responses, even when the waiting interval to respond was increased. However, unlike NP rats, P rats were faster to enter the food magazine and spent more time in this area. In addition, P rats showed higher levels of goal-tracking responses than NP rats, as measured by the number of magazine nose-pokes during the presentation of a food conditioned stimulus. By contrast, NP showed higher levels of sign-tracking behaviour than P rats. Following a 4-week exposure to intermittent alcohol we confirmed that P rats had a marked preference for, and consumed more alcohol than, NP rats, but were not more impulsive when re-tested in the 5-CSRTT. These findings indicate that high alcohol preferring and drinking P rats are neither intrinsically impulsive nor do they exhibit impulsivity after exposure to alcohol. However, P rats do show increased goal-directed behaviour to food incentives and this may be associated with their strong preference for alcohol.

  6. TCR-contacting residues orientation and HLA-DRβ* binding preference determine long-lasting protective immunity against malaria

    Energy Technology Data Exchange (ETDEWEB)

    Alba, Martha P.; Suarez, Carlos F. [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Universidad del Rosario, Bogotá D. C. (Colombia); Universidad de Ciencias Aplicadas y Ambientales (UDCA), Bogotá (Colombia); Varela, Yahson [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Patarroyo, Manuel A.; Bermudez, Adriana [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Universidad del Rosario, Bogotá D. C. (Colombia); Patarroyo, Manuel E., E-mail: mepatarr@gmail.com [Fundación Instituto de Inmunología de Colombia (FIDIC), Bogotá D. C. (Colombia); Universidad Nacional de Colombia, Bogotá D. C. (Colombia)

    2016-09-02

    Fully-protective, long-lasting, immunological (FPLLI) memory against Plasmodium falciparum malaria regarding immune protection-inducing protein structures (IMPIPS) vaccinated into monkeys previously challenged and re-challenged 60 days later with a lethal Aotus monkey-adapted P. falciparum strain was found to be associated with preferential high binding capacity to HLA-DRβ1* allelic molecules of the major histocompatibility class II (MHC-II), rather than HLA-DRβ3*, β4*, β5* alleles. Complete PPII{sub L} 3D structure, a longer distance (26.5 Å ± 1.5 Å) between residues perfectly fitting into HLA-DRβ1*PBR pockets 1 and 9, a gauche{sup −} rotamer orientation in p8 TCR-contacting polar residue and a larger volume of polar p2 residues was also found. This data, in association with previously-described p3 and p7 apolar residues having gauche{sup +} orientation to form a perfect MHC-II-peptide-TCR complex, determines the stereo-electronic and topochemical characteristics associated with FPLLI immunological memory. - Highlights: • Stereo-electronic and topochemical rules associated with FPLLI immunological memory. • Presence of very high long-lasting antibody titres against Plasmodium falciparum Spz. • Protective memory induction associated with a binding capacity to HLA-DRβ1*. • gauche{sup −} rotamer orientation in p8 polar residue is related to is related to immunological memory.

  7. Dependence of improper ferroelectricity on the preferred orientation of Mn3 spins in CaMn7O12

    Science.gov (United States)

    Dai, Jian-Qing

    2017-02-01

    The improper ferroelectricity of CaMn7O12 is studied by examining the influence of the orientation angle of Mn3 spins on the basis of first-principles density functional theory. We analyze the helicoidal magnetic order induced forces, ionic displacements, and polarization contributions from both atomic and mode- decomposition viewpoints. Our work unambiguously reveals the critical role of the orientation angle of Mn3 spins in determining the improper ferroelectricity of CaMn7O12. The ferroelectric polarization can be reversed by changing the orientation angle of Mn3 spins without switching spin chirality of the helicoidal magnetic order. We demonstrate that the particular helicoidal magnetic order induces remarkable mismatch of the Born effective charges with the lattice symmetry, which leads to the dominant contribution to ferroelectric polarization from purely Raman-type ionic displacements. However, this significant polarization contribution from the purely Raman-type distortion cannot survive in the absence of IR-active ionic displacements.

  8. Steric effect is a decisive factor on the orientation preference of guest into host: evidence from 5-indanol/β-CD model

    Science.gov (United States)

    Sivakumar, K.; Nichodemus, M.; Sankaran, K. R.

    2014-07-01

    The present study evidences the role of steric effect in the orientation preference of guest into host using the 1:1 inclusion complex of 5-indanol/β-CD model. Two different orientations of guest (5-indanol) into host (β-CD) are considered for the inclusion of 5-indanol into the cavity through the 2° rim of β-CD. The energy differences in the inclusion process are calculated using PM3 semi-empirical method and HF/6-31G** basis set. By the investigation of stabilisation energies, it is found that the energy of both orientations increases to maximum value due to the increase of steric repulsive effect when the crowding of bulky group of 5-indanol occurs at 1° or 2° rim of β-CD. On comparing the fluorescence spectral data of 5-indanol:β-CD complex and 2-napthol:β-CD complex, it is observed that the steric effect is intensified due to the presence of bulky group.

  9. Determination of crystallographic intensities from sparse data

    Directory of Open Access Journals (Sweden)

    Kartik Ayyer

    2015-01-01

    Full Text Available X-ray serial microcrystallography involves the collection and merging of frames of diffraction data from randomly oriented protein microcrystals. The number of diffracted X-rays in each frame is limited by radiation damage, and this number decreases with crystal size. The data in the frame are said to be sparse if too few X-rays are collected to determine the orientation of the microcrystal. It is commonly assumed that sparse crystal diffraction frames cannot be merged, thereby setting a lower limit to the size of microcrystals that may be merged with a given source fluence. The EMC algorithm [Loh & Elser (2009, Phys. Rev. E, 80, 026705] has previously been applied to reconstruct structures from sparse noncrystalline data of objects with unknown orientations [Philipp et al. (2012, Opt. Express, 20, 13129–13137; Ayyer et al. (2014, Opt. Express, 22, 2403–2413]. Here, it is shown that sparse data which cannot be oriented on a per-frame basis can be used effectively as crystallographic data. As a proof-of-principle, reconstruction of the three-dimensional diffraction intensity using sparse data frames from a 1.35 kDa molecule crystal is demonstrated. The results suggest that serial microcrystallography is, in principle, not limited by the fluence of the X-ray source, and collection of complete data sets should be feasible at, for instance, storage-ring X-ray sources.

  10. Crystallographic topology and its applications

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, C.K.; Burnett, M.N. [Oak Ridge National Lab., TN (United States); Dunbar, W.D. [Simon`s Rock Coll., Great Barrington, MA (United States). Div. of Natural Sciences and Mathematics

    1996-10-01

    Geometric topology and structural crystallography concepts are combined to define a new area we call Structural Crystallographic Topology, which may be of interest to both crystallographers and mathematicians. In this paper, we represent crystallographic symmetry groups by orbifolds and crystal structures by Morse - functions. The Morse function uses mildly overlapping Gaussian thermal-motion probability density functions centered on atomic sites to form a critical net with peak, pass, pale, and pit critical points joined into a graph by density gradient-flow separatrices. Critical net crystal structure drawings can be made with the ORTEP-III graphics pro- An orbifold consists of an underlying topological space with an embedded singular set that represents the Wyckoff sites of the crystallographic group. An orbifold for a point group, plane group, or space group is derived by gluing together equivalent edges or faces of a crystallographic asymmetric unit. The critical-net-on-orbifold model incorporates the classical invariant lattice complexes of crystallography and allows concise quotient-space topological illustrations to be drawn without the repetition that is characteristic of normal crystal structure drawings.

  11. CIF (Crystallographic Information File): A Standard for Crystallographic Data Interchange

    Science.gov (United States)

    Brown, I. D.

    1996-01-01

    The Crystallographic Information File (CIF) uses the self-defining STAR file structure. This requires the creation of a dictionary of data names and definitions. A basic dictionary of terms needed to describe the crystal structures of small molecules was approved in 1991 and is currently used for the submission of papers to Acta Crystallographica C. A number of extensions to this dictionary are in preparation. By storing the dictionary itself as a STAR file, the definitions and relationships in the CIF dictionary become computer interpretable. This offers many possibilities for the automatic handling of crystallographic information. PMID:27805170

  12. The birth of the European Crystallographic Committee (ECC) and of the European Crystallographic Meetings (ECMs)

    Science.gov (United States)

    Authier, A.

    2010-01-01

    This article describes the circumstances of the establishment of the European Crystallographic Committee, now the European Crystallographic Association, a regional associate of the IUCr, and of the European Crystallographic Meetings.

  13. Influence of the angle between cleavage and bedding on the anisotropy of magnetic susceptibility and the degree of phyllosilicate preferred orientation

    Science.gov (United States)

    Debacker, T. N.; Sintubin, M.

    2003-04-01

    Due to the common scarcity of strain markers and the often fine-grained lithologies, performing strain analyses in slate belts may be difficult. As an alternative, one may use methods such as phyllosilicate preferred orientation (X-ray pole figure goniometry) and anisotropy of magnetic susceptibility (AMS). However, a large number of factors influence the results of these analytical methods. One of the factors is the angle between cleavage and bedding. The study area is the Brabant Massif, a single-phase deformed, low-grade slate belt in N-Belgium consisting of a steep Cambrian core surrounded by Ordovician-Silurian sequences. In the southern part of the Cambrian core, the transition between steeply plunging folds, considered typical for the steep core, and gently plunging folds, considered characteristic for the peripheral Ordovician-Silurian sequences, occurs in homogeneous mudstones of the Lower Cambrian Oisquercq Formation. In these deposits mica and chlorite show a similar degree of preferred orientation. Mica is always aligned along the cleavage, whereas chlorite is aligned along the bedding. Clear intersection pole figure patterns characterise samples with large cleavage/bedding angles, whereas flattening fabrics only become apparent for samples with small cleavage/bedding angles. For both mica and chlorite, the degree of preferred orientation is higher for samples with small cleavage/bedding angles. The magnetic fabric shows prolate susceptibility ellipsoids for samples with large cleavage/bedding angles and oblate susceptibility ellipsoids for samples with small cleavage/bedding angles (cf. Housen et al., 1993). The short axis of the susceptibility ellipsoid is generally oriented perpendicular to bedding, occasionally perpendicular to cleavage or with an intermediate orientation. The long axis of the susceptibility ellipsoid is always parallel to the cleavage/bedding intersection. The shape parameter T shows an almost linear relationship with respect to

  14. Methods for investigating the local spatial anisotropy and the preferred orientation of cones in adaptive optics retinal images

    Science.gov (United States)

    Cooper, Robert F.; Lombardo, Marco; Carroll, Joseph; Sloan, Kenneth R.; Lombardo, Giuseppe

    2016-01-01

    The ability to non-invasively image the cone photoreceptor mosaic holds significant potential as a diagnostic for retinal disease. Central to the realization of this potential is the development of sensitive metrics for characterizing the organization of the mosaic. Here we evaluated previously-described (Pum et al., 1990) and newly-developed (Fourier- and Radon-based) methods of measuring cone orientation in both simulated and real images of the parafoveal cone mosaic. The proposed algorithms correlated well across both simulated and real mosaics, suggesting that each algorithm would provide an accurate description of individual photoreceptor orientation. Despite the high agreement between algorithms, each performed differently in response to image intensity variation and cone coordinate jitter. The integration property of the Fourier transform allowed the Fourier-based method to be resistant to cone coordinate jitter and perform the most robustly of all three algorithms. Conversely, when there is good image quality but unreliable cone identification, the Radon algorithm performed best. Finally, in cases where both the image and cone coordinate reliability was excellent, the method of Pum et al. (1990) performed best. These descriptors are complementary to conventional descriptive metrics of the cone mosaic, such as cell density and spacing, and have the potential to aid in the detection of photoreceptor pathology. PMID:27484961

  15. The Crystallographic Information File (CIF

    Directory of Open Access Journals (Sweden)

    I D Brown

    2006-11-01

    Full Text Available The Crystallographic Information File (CIF, owned by the International Union of Crystallography, is a file structure based on tag-value ASCII pairs with tags defined in machine-readable dictionaries. The crystallographic community publishes and archives large quantities of numeric information generated by crystal structure determinations, and CIF's acceptance was assured by its adoption as the submission format for Acta Crystallographica and by the obvious needs of the community. CIF's strength lies in its dictionaries, which define most of the concepts of crystallography; its weakness is the difficulty of writing software that exploits its full potential.

  16. Carbonado revisited: Insights from neutron diffraction, high resolution orientation mapping and numerical simulations

    Science.gov (United States)

    Piazolo, Sandra; Kaminsky, Felix V.; Trimby, Patrick; Evans, Lynn; Luzin, V.

    2016-11-01

    One of the most controversial diamond types is carbonado, as its origin and geological history are still under debate. Here, we investigate selected carbonado samples using neutron diffraction and high resolution orientation mapping in combination with numerical simulations. Neutron diffraction analyses show that fine grained carbonado samples exhibit a distinct lack of crystallographic preferred orientation. Quantitative crystallographic orientation analyses performed on transmission electron microscope (TEM) sections reveal that the 2-10 μm grains exhibit locally significant internal deformation. Such features are consistent with crystal plastic deformation of a grain aggregate that initially formed by rapid nucleation, characterized by a high number of nucleation sites and no crystallographic preferred orientation. Crystal plastic deformation resulted in high stress heterogeneities close to grain boundaries, even at low bulk strains, inducing a high degree of lattice distortion without significant grain size reduction and the development of a crystallographic preferred orientation. Observed differences in the character of the grain boundary network and internal deformation structures can be explained by significant post-deformation annealing occurring to variable degrees in the carbonado samples. Differences in intensity of crystal bending and subgrain boundary sharpness can be explained by dislocation annihilation and rearrangement, respectively. During annealing grain energy is reduced resulting in distinct changes to the grain boundary geometry. Grain scale numerical modelling shows that anisotropic grain growth, where grain boundary energy is determined by the orientation of a boundary segment relative to the crystallographic orientation of adjacent grains results in straight boundary segments with abrupt changes in orientation even if the boundary is occurring between two triple junctions forming a "zigzag" pattern. In addition, in diamond anisotropic

  17. Crystallographic Lattice Boltzmann Method

    Science.gov (United States)

    Namburi, Manjusha; Krithivasan, Siddharth; Ansumali, Santosh

    2016-01-01

    Current approaches to Direct Numerical Simulation (DNS) are computationally quite expensive for most realistic scientific and engineering applications of Fluid Dynamics such as automobiles or atmospheric flows. The Lattice Boltzmann Method (LBM), with its simplified kinetic descriptions, has emerged as an important tool for simulating hydrodynamics. In a heterogeneous computing environment, it is often preferred due to its flexibility and better parallel scaling. However, direct simulation of realistic applications, without the use of turbulence models, remains a distant dream even with highly efficient methods such as LBM. In LBM, a fictitious lattice with suitable isotropy in the velocity space is considered to recover Navier-Stokes hydrodynamics in macroscopic limit. The same lattice is mapped onto a cartesian grid for spatial discretization of the kinetic equation. In this paper, we present an inverted argument of the LBM, by making spatial discretization as the central theme. We argue that the optimal spatial discretization for LBM is a Body Centered Cubic (BCC) arrangement of grid points. We illustrate an order-of-magnitude gain in efficiency for LBM and thus a significant progress towards feasibility of DNS for realistic flows. PMID:27251098

  18. Long-term effects of user preference-oriented recommendation method on the evolution of online system

    Science.gov (United States)

    Shi, Xiaoyu; Shang, Ming-Sheng; Luo, Xin; Khushnood, Abbas; Li, Jian

    2017-02-01

    As the explosion growth of Internet economy, recommender system has become an important technology to solve the problem of information overload. However, recommenders are not one-size-fits-all, different recommenders have different virtues, making them be suitable for different users. In this paper, we propose a novel personalized recommender based on user preferences, which allows multiple recommenders to exist in E-commerce system simultaneously. We find that output of a recommender to each user is quite different when using different recommenders, the recommendation accuracy can be significantly improved if each user is assigned with his/her optimal personalized recommender. Furthermore, different from previous works focusing on short-term effects on recommender, we also evaluate the long-term effect of the proposed method by modeling the evolution of mutual feedback between user and online system. Finally, compared with single recommender running on the online system, the proposed method can improve the accuracy of recommendation significantly and get better trade-offs between short- and long-term performances of recommendation.

  19. Crystallographic properties of fertilizer compounds

    Energy Technology Data Exchange (ETDEWEB)

    Frazier, A.W.; Dillard, E.F.; Thrasher, R.D.; Waerstad, K.R.; Hunter, S.R.; Kohler, J.J.; Scheib, R.M.

    1991-02-01

    This bulletin is a compilation of crystallographic data collected at NFERC on 450 fertilizer-related compounds. In TVA's fertilizer R and D program, petrographic examination, XRD, and infrared spectroscopy are combined with conventional chemical analysis methods in identifying the individual compounds that occur in fertilizer materials. This handbook brings together the results of these characterization studies and supplemental crystallographic data from the literature. It is in one-compound-per-page, loose-leaf format, ordered alphabetically by IUPAC name. Indexes provided include IUPAC name, formula, group, alternate formula, synonyms, x-ray data, optical data. Tables are given for solids, compounds in commercial MAP and DAP, and matrix materials in phosphate rock.

  20. Antisolvent crystallization of pharmaceutical excipients from aqueous solutions and the use of preferred orientation in phase identification by powder X-ray diffraction.

    Science.gov (United States)

    Crisp, J L; Dann, S E; Blatchford, C G

    2011-04-18

    Crystallization of lactose from 10% (w/v) aqueous solutions was investigated with the use of polar antisolvents. Crystal growth was observed at 50-65% antisolvent content and showed a morphological transition from a polyhedral to needle-like habit with increasing antisolvent content, which coincided with a polymorphic transition from alpha lactose monohydrate (Lα·H(2)O) to beta lactose (Lβ). Where dehydrating antisolvents were employed such as methanol and ethanol, evidence of Lα·H(2)O dehydration to form Lα(S) was also observed at 95% antisolvent content. Powder X-ray diffraction (PXRD) analysis of the crystals highlighted the preferred orientation effects exhibited by large crystals of this kind, indicating the difficulties experienced by the non-specialist when performing phase identification of lactose polymorphs. The same studies were applied to raffinose pentahydrate, trehalose dihydrate and mannitol to assess the effects of crystallization conditions on other pharmaceutical excipients. Copyright © 2011 Elsevier B.V. All rights reserved.

  1. Crystallographic Analysis of Nucleation at Hardness Indentations in High-Purity Aluminum

    Science.gov (United States)

    Xu, Chaoling; Zhang, Yubin; Lin, Fengxiang; Wu, Guilin; Liu, Qing; Juul Jensen, Dorte

    2016-12-01

    Nucleation at Vickers hardness indentations has been studied in high-purity aluminum cold-rolled 12 pct. Electron channeling contrast was used to measure the size of the indentations and to detect nuclei, while electron backscattering diffraction was used to determine crystallographic orientations. It is found that indentations are preferential nucleation sites. The crystallographic orientations of the deformed grains affect the hardness and the nucleation potentials at the indentations. Higher hardness gives increased nucleation probabilities. Orientation relationships between nuclei developed at different indentations within one original grain are analyzed and it is found that the orientation distribution of the nuclei is far from random. It is suggested that it relates to the orientations present near the indentation tips which in turn depend on the orientation of the selected grain in which they form. Finally, possible nucleation mechanisms are briefly discussed.

  2. Relationship between open-circuit voltage in Cu(In,Ga)Se{sub 2} solar cell and peak position of (220/204) preferred orientation near its absorber surface

    Energy Technology Data Exchange (ETDEWEB)

    Chantana, J., E-mail: jakapan@fc.ritsumei.ac.jp; Minemoto, T. [Department of Electrical and Electronic Engineering, Ritsumeikan University, 1-1-1 Nojihigashi, Kusatsu, Shiga 525-8577 (Japan); Watanabe, T.; Teraji, S.; Kawamura, K. [Environment and Energy Research Center, Nitto Denko Corporation, 2-8 Yamadaoka, Suita, Osaka 565-0871 (Japan)

    2013-11-25

    Cu(In,Ga)Se{sub 2} (CIGS) absorbers with various Ga/III, Ga/(In+Ga), profiles are prepared by the so-called “multi-layer precursor method” using multi-layer co-evaporation of material sources. It is revealed that open-circuit voltage (V{sub OC}) of CIGS solar cell is primarily dependent on averaged Ga/III near the surface of its absorber. This averaged Ga/III is well predicted by peak position of (220/204) preferred orientation of CIGS film near its surface investigated by glancing-incidence X-ray diffraction with 0.1° incident angle. Finally, the peak position of (220/204) preferred orientation is proposed as a measure of V{sub OC} before solar cell fabrication.

  3. Crystallographic Analysis of Nucleation at Hardness Indentations in High-Purity Aluminum

    DEFF Research Database (Denmark)

    Xu, Chaoling; Zhang, Yubin; Lin, Fengxiang

    2016-01-01

    Nucleation at Vickers hardness indentations has been studied in high-purity aluminum cold-rolled 12 pct. Electron channeling contrast was used to measure the size of the indentations and to detect nuclei, while electron backscattering diffraction was used to determine crystallographic orientations...

  4. Internet Based Open Access Crystallographic Databases

    Science.gov (United States)

    Upreti, Girish; Seipel, Bjoern; Harvey, Morgan; Garrick, Will; Moeck, Peter

    2006-05-01

    Two freely accessible crystallographic databases are discussed: the Crystallographic Open Database (COD, http://crystallography.net) which contains over 37,000 crystal structures, and the Nano-Crystallography Database (NCD, http://nanocrystallography.research.pdx.edu) which we recently started to support image-based nanocrystallography and (nano) materials science education. Both databases collect crystallographic relevant information in a standardized format; the Crystallographic Information File (CIF). CIF is the standard file format adopted by the International Union of Crystallography (http://iucr.org) for the archiving and distribution of crystallographic information. A subset of the COD, the Predicted Crystallographic Online Database, allows for 3D structural displays of structural polyhedra and wireframes of approximately 2,600 entries. Since electron microscopist are interested in simple, yet technologically important materials, the crystallographic information for those materials will be included in our database. At our NCD site, entries in the COD and the NCD can be visualized in three dimensions (3D) along with (2D) lattice fringe fingerprints plots. The latter supports the identification of unknown nanocrystal phases from high-resolution transmission electron microscopy (HRTEM) images. Morphological crystal information from the database ``Bestimmungstabellen f"ur Kristalle/ ???????????? ??????????,'' (A.K. Boldyrew and W.W. Doliwo-Dobrowolsky, Zentrales Wissenschaftlichers Institute der Geologie und Sch"urfung, Leningrad/ Moscow, 1937/1939) will also be included in the NCD to support image-based nanocrystallography in 3D.

  5. Shape and crystallographic orientation of nanodiamonds for quantum sensing

    NARCIS (Netherlands)

    Ong, S. Y.; Chipaux, M.; Nagl, A.; Schirhagl, R.

    2017-01-01

    Nanodiamonds with dimensions down to a few tens of nanometers containing nitrogen-vacancy (NV) color centers have revealed their potential as powerful and versatile quantum sensors with a unique combination of spatial resolution and sensitivity. The NV centers allow transducing physical properties,

  6. The New NRL Crystallographic Database

    Science.gov (United States)

    Mehl, Michael; Curtarolo, Stefano; Hicks, David; Toher, Cormac; Levy, Ohad; Hart, Gus

    For many years the Naval Research Laboratory maintained an online graphical database of crystal structures for a wide variety of materials. This database has now been redesigned, updated and integrated with the AFLOW framework for high throughput computational materials discovery (http://materials.duke.edu/aflow.html). For each structure we provide an image showing the atomic positions; the primitive vectors of the lattice and the basis vectors of every atom in the unit cell; the space group and Wyckoff positions; Pearson symbols; common names; and Strukturbericht designations, where available. References for each structure are provided, as well as a Crystallographic Information File (CIF). The database currently includes almost 300 entries and will be continuously updated and expanded. It enables easy search of the various structures based on their underlying symmetries, either by Bravais lattice, Pearson symbol, Strukturbericht designation or commonly used prototypes. The talk will describe the features of the database, and highlight its utility for high throughput computational materials design. Work at NRL is funded by a Contract with the Duke University Department of Mechanical Engineering.

  7. Defining the Crystallographic Fingerprint of Extraterrestrial Treasures

    Science.gov (United States)

    Forman, L. V.; Bland, P. A.; Timms, N. E.; Daly, L.; Benedix, G. K.; Trimby, P. W.

    2016-08-01

    An approach to determine the crystallographic fingerprint of chondritic matrix grains, which is complimentary to the geochemical signature commonly identified to constrain some aspects of the petrogenesis of a sample.

  8. Surface chemistry of the preferred (111) and (220) crystal oriented microcrystalline Si films by radio-frequency plasma-enhanced chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Ohba, Daisuke; Koshino, Hideto; Tang, Zeguo; Shirai, Hajime [Graduate School of Science and Engineering, Saitama University, Sakura (Japan)

    2011-10-15

    The surface chemistry of the preferentially (111) and (220) crystal orientated chlorinated hydrogenated microcrystalline silicon ({mu}c-Si:H:Cl) films was studied using a rf PE-CVD of a dichlorosilane (SiH{sub 2}Cl{sub 2}) and H{sub 2} mixture. The growing surface for the preferentially (220) crystal oriented {mu}c-Si:H:Cl films included much voids and dangling bonds, whereas the growing surface with the preferential (111) crystal orientation was chemically stable relatively. These findings suggest that the sticking process of deposition precursors and/or the reconstruction of Si clusters within the sub-surface determine the preferential crystal orientation. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  9. Oriented grain growth and modification of 'frozen anisotropy' in the lithospheric mantle

    Science.gov (United States)

    Boneh, Yuval; Wallis, David; Hansen, Lars N.; Krawczynski, Mike J.; Skemer, Philip

    2017-09-01

    Seismic anisotropy throughout the oceanic lithosphere is often assumed to be generated by fossilized texture formed during deformation at asthenospheric temperatures close to the ridge. Here we investigate the effect of high-temperature and high-pressure static annealing on the texture of previously deformed olivine aggregates to simulate residence of deformed peridotite in the lithosphere. Our experiments indicate that the orientation and magnitude of crystallographic preferred orientation (CPO) will evolve due to the preferential growth of grains with low dislocation densities. These observations suggest that texture and stored elastic strain energy promote a style of grain growth that modifies the CPO of a deformed aggregate. We demonstrate that these microstructural changes alter the orientation distributions and magnitudes of seismic wave velocities and anisotropy. Therefore, static annealing may complicate the inference of past deformation kinematics from seismic anisotropy in the lithosphere.

  10. Tuning the Photocatalytic Activity of Anatase TiO2 Thin Films by Modifying the Preferred <001> Grain Orientation with Reactive DC Magnetron Sputtering

    Directory of Open Access Journals (Sweden)

    B. Stefanov

    2014-08-01

    Full Text Available Anatase TiO2 thin films were deposited by DC reactive magnetron sputtering on glass substrates at 20 mTorr pressure in a flow of an Ar and O2 gas mixture. The O2 partial pressure (PO2 was varied from 0.65 mTorr to 1.3 mTorr to obtain two sets of films with different stoichiometry. The structure and morphology of the films were characterized by secondary electron microscopy, atomic force microscopy, and grazing-angle X-ray diffraction complemented by Rietveld refinement. The as-deposited films were amorphous. Post-annealing in air for 1 h at 500 °C resulted in polycrystalline anatase film structures with mean grain size of 24.2 nm (PO2 = 0.65 mTorr and 22.1 nm (PO2 = 1.3 mTorr, respectively. The films sputtered at higher O2 pressure showed a preferential orientation in the <001> direction, which was associated with particle surfaces exposing highly reactive {001} facets. Films sputtered at lower O2 pressure exhibited no, or very little, preferential grain orientation, and were associated with random distribution of particles exposing mainly the thermodynamically favorable {101} surfaces. Photocatalytic degradation measurements using methylene blue dye showed that <001> oriented films exhibited approximately 30% higher reactivity. The measured intensity dependence of the degradation rate revealed that the UV-independent rate constant was 64% higher for the <001> oriented film compared to randomly oriented films. The reaction order was also found to be higher for <001> films compared to randomly oriented films, suggesting that the <001> oriented film exposes more reactive surface sites.

  11. V(D)J recombination of chromosomally integrated, wild-type deletional and inversional substrates occur at similar frequencies with no preference for orientation.

    Science.gov (United States)

    Shuh, Maureen; Hixson, Douglas C

    2005-02-15

    Efficient and correct recombination of V(D)J substrates results in the generation of antibodies. The RSS substrates are oriented in two directions with respect to each other: deletional and inversional. Deletional recombination results in the formation of the coding joint and excision of the intervening sequences. Inversional recombination retains all the genomic sequences and forms both a coding joint and a signal joint. A bias for deletional recombination has been characterized with specific loci in vivo and recapitulated in experiments using extrachromosomal substrates. We constructed retroviral substrates of RSS in the deletional and inversional orientation. We introduced the substrates into wild-type and scid pre-B cells and measured the frequency of functional recombination in addition to open/shut recombination. We also mutated the RSSs to determine whether mutated sequences influenced orientation bias. We show that pre-B cells recombine the wild-type substrates at a 1.6 ratio of deletion:inversion. Nonamer mutated substrates recombined with a deletional bias whereas heptamer mutated substrates recombined with an inversional bias. A spacer length mutation and drastic mutations in the RSS abolish all recombination. These results suggest that there is no orientation bias with wild-type RSSs but that orientation bias occurs when RSSs are mutated.

  12. Nexus, crystallographic computing all around the world.

    Science.gov (United States)

    Cranswick, Lachlan Michael David; Bisson, William; Cockcroft, Jeremy Karl

    2008-01-01

    Crystallographic Nexus CD-ROMs, containing a range of free crystallographic software for single-crystal and powder diffraction available on the Internet, have been distributed on request since 1996. The free CD is made in the form of a ;virtual Internet' with the main intent of benefiting crystallographers with inadequate Internet access. The IUCr funds an annual/biennial update which is distributed to known previous recipients. Feedback from current recipients indicates the CD is still useful. The most current IUCr-funded CD is being produced by the CCP14 project at University College London and The Royal Institution UK for distribution to the ECM 2007 and AsCA 2007 conferences.

  13. Crystallographic properties of magnetron sputtered barium ferrite films

    Energy Technology Data Exchange (ETDEWEB)

    Capraro, S. [Laboratoire DIOM, University of Saint-Etienne, 23 rue Michelon, 42023 Saint-Etienne Cedex (France)]. E-mail: stephane.capraro@univ-st-etienne.fr; Berre, M. Le [LPM, UMR 5511, INSA Lyon, 7 av. Jean Capelle, 69621 Villeurbanne Cedex (France); Chatelon, J.P. [Laboratoire DIOM, University of Saint-Etienne, 23 rue Michelon, 42023 Saint-Etienne Cedex (France); Bayard, B. [Laboratoire DIOM, University of Saint-Etienne, 23 rue Michelon, 42023 Saint-Etienne Cedex (France); Joisten, H. [CEA-LETI, 17 rue des martyrs, 38041 Grenoble Cedex (France); Canut, C. [LPMCN, University Lyon I, 43 Bvd. du 11 novembre 1918, 69622 Villerbanne, Cedex (France); Barbier, D. [LPM, UMR 5511, INSA Lyon, 7 av. Jean Capelle, 69621 Villeurbanne Cedex (France); Rousseau, J.J. [Laboratoire DIOM, University of Saint-Etienne, 23 rue Michelon, 42023 Saint-Etienne Cedex (France)

    2004-09-15

    The development of devices combining a ferrite with a semiconductor chip is a major focus of current research. Barium hexaferrite (BaFe{sub 12}O{sub 19} or BaM) thick films are deposited here using a RF magnetron sputtering system. Films are amorphous and non magnetic after deposition. Post-deposition thermal annealing is employed to make the films crystallize. The effects of the substrate, thermal annealing process, thickness, substrate temperature on crystallographic properties and stoichiometry are studied using a X-ray diffractometry (XRD) and Rutherford back-scattering (RBS). The in-depth homogeneity of Ba, Fe and O is evaluated by secondary ion mass spectroscopy (SIMS). The study shows a good crystallization of BaM films and there is a preferential orientation among the crystallographic planes (1 0 1), (2 0 0), (2 0 3), (1 0 2), (1 1 0) and (2 0 5) when BaM films are prepared at low RF power and when the substrate is heated. For several elaboration parameters, grains size is in the range of 25 and 40 nm and BaM films are stoichiometric with regard to the target stoichiometry.

  14. Non-Crystallographic Symmetry in Packing Spaces

    Directory of Open Access Journals (Sweden)

    Valery G. Rau

    2013-01-01

    Full Text Available In the following, isomorphism of an arbitrary finite group of symmetry, non-crystallographic symmetry (quaternion groups, Pauli matrices groups, and other abstract subgroups, in addition to the permutation group, are considered. Application of finite groups of permutations to the packing space determines space tilings by policubes (polyominoes and forms a structure. Such an approach establishes the computer design of abstract groups of symmetry. Every finite discrete model of the real structure is an element of symmetry groups, including non-crystallographic ones. The set packing spaces of the same order N characterizes discrete deformation transformations of the structure.

  15. Study on the effects of Ga-2N high co-doping and preferred orientation on the stability, bandgap and absorption spectrum of ZnO

    Science.gov (United States)

    Hou, Qing-Yu; Li, Wen-Cai; Qu, Ling-Feng; Zhao, Chun-Wang

    2017-06-01

    Currently, the stability and visible light properties of Ga-2N co-doped ZnO systems have been studied extensively by experimental analysis and theoretical calculations. However, previous theoretical calculations arbitrarily assigned Ga- and 2N-doped sites in ZnO. In addition, the most stable and possible doping orientations of doped systems have not been fully and systematically considered. Therefore, in this paper, the electron structure and absorption spectra of the unit cells of doped and pure systems were calculated by first-principles plane-wave ultrasoft pseudopotential with the GGA+U method. Calculations were performed for pure ZnO, Ga-2N supercells heavily co-doped with Zn1-xGaxO1-yNy (x = 0.03125 - 0.0625, y = 0.0625 - 0.125) under different co-doping orientations and conditions, and the Zn16GaN2O14 interstitial model. The results indicated that under different orientations and constant Ga-2N co-doping concentrations, the systems co-doped with Ga-N atoms vertically oriented to the c-axis and with another N atom located in the nearest-neighboring site exhibited higher stability over the others, thus lowering formation energy and facilitating doping. Moreover, Ga-interstitial- and 2N-co-doped ZnO systems easily formed chemical compounds. Increasing co-doping concentration while the co-doping method remained constant decreased doped system volume and lowered formation energies. Meantime, co-doped systems were more stable and doping was facilitated. The bandgap was also narrower and red shifting of the absorption spectrum was more significant. These results agreed with previously reported experimental results. In addition, the absorption spectra of Ga-interstitial- and 2N-co-doped ZnO both blue shifted in the UV region compared with that of the pure ZnO system.

  16. Ocean acidification reduces the crystallographic control in juvenile mussel shells.

    Science.gov (United States)

    Fitzer, Susan C; Cusack, Maggie; Phoenix, Vernon R; Kamenos, Nicholas A

    2014-10-01

    Global climate change threatens the oceans as anthropogenic carbon dioxide causes ocean acidification and reduced carbonate saturation. Future projections indicate under saturation of aragonite, and potentially calcite, in the oceans by 2100. Calcifying organisms are those most at risk from such ocean acidification, as carbonate is vital in the biomineralisation of their calcium carbonate protective shells. This study highlights the importance of multi-generational studies to investigate how marine organisms can potentially adapt to future projected global climate change. Mytilus edulis is an economically important marine calcifier vulnerable to decreasing carbonate saturation as their shells comprise two calcium carbonate polymorphs: aragonite and calcite. M. edulis specimens were cultured under current and projected pCO2 (380, 550, 750 and 1000μatm), following 6months of experimental culture, adults produced second generation juvenile mussels. Juvenile mussel shells were examined for structural and crystallographic orientation of aragonite and calcite. At 1000μatm pCO2, juvenile mussels spawned and grown under this high pCO2 do not produce aragonite which is more vulnerable to carbonate under-saturation than calcite. Calcite and aragonite were produced at 380, 550 and 750μatm pCO2. Electron back scatter diffraction analyses reveal less constraint in crystallographic orientation with increased pCO2. Shell formation is maintained, although the nacre crystals appear corroded and crystals are not so closely layered together. The differences in ultrastructure and crystallography in shells formed by juveniles spawned from adults in high pCO2 conditions may prove instrumental in their ability to survive ocean acidification. Copyright © 2014 Elsevier Inc. All rights reserved.

  17. Influence of Preferred Orientation on the Performance of Brazing Diamond Core Drill Bit%择优取向对钎焊金刚石薄壁钻性能影响

    Institute of Scientific and Technical Information of China (English)

    杨合丹; 刘一波; 陈哲; 刘胜

    2015-01-01

    Brazing diamond core drill bit is a type of high-performance superhard material drilling tool which adopts the vacuum brazing technology.In view of the inherent feature of drilling tools,preferred orientation has been adopted for abrasive on the top and com-bined crystal edges of (1 1 1)and (1 10)face has been taken as blade edge of the diamond. This type of drill has a sharp Cutting-edge,smooth chip evacuation and less friction heat and presents high drilling efficiency and long service life.The actual drilling test shows that service life of preferred orientationФ6 and Ф32mm drill bits is almost doubled com-pared to conventional drill bit and the average drilling rate has been improved by over 50% with a very smooth drilling performance;service life of preferred orientationФ32mm has been increased by over 30% compared to uniform bit and the drilling stability of them is similar.%钎焊金刚石薄壁钻是一种采用真空钎焊技术进行的高性能超硬材料钻削工具。根据钻削工具的固有特征,将顶部磨料择优取向,取金刚石岀刃点为(111)面与(110)面结合晶棱,在钻削过程中刃口锋利,排屑顺畅,摩擦生热少,显示出极高的钻进效率和使用寿命。通过实际钻进验证可知:择优取向Φ6小钻头寿命比普通钻头提高接近1倍,平均钻速提高50%以上,并且钻进非常平稳;择优取向Φ32mm 常规钻头寿命比普通钻头提高1倍以上,平均钻速提高50%以上,并且钻进非常平稳;择优取向Φ32mm 常规钻头寿命比均布钻头提高30%以上,钻进平稳性相当。

  18. Sonicated sol–gel preparation of nanoparticulate ZnO thin films with various deposition speeds: The highly preferred c-axis (0 0 2) orientation enhances the final properties

    Energy Technology Data Exchange (ETDEWEB)

    Malek, M.F., E-mail: firz_solarzelle@yahoo.com [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor (Malaysia); Mamat, M.H. [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor (Malaysia); Khusaimi, Z. [NANO-SciTech Centre (NST), Institute of Science (IOS), Universiti Teknologi MARA UiTM, 40450 Shah Alam, Selangor (Malaysia); Sahdan, M.Z. [Microelectronic and Nanotechnology Centre (MiNT), Universiti Tun Hussein Onn Malaysia (UTHM), 86400 Batu Pahat, Johor (Malaysia); Musa, M.Z. [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor (Malaysia); Zainun, A.R. [Faculty of Electrical and Electronics Engineering, Universiti Malaysia Pahang (UMP), Lebuhraya Tun Razak, 26300 Kuantan, Pahang (Malaysia); Suriani, A.B. [Department of Physics, Faculty of Science and Mathematics, Universiti Pendidikan Sultan Idris, 35900 Tanjung Malim, Perak (Malaysia); Md Sin, N.D. [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor (Malaysia); Abd Hamid, S.B. [Nanotechnology and Catalysis Research Centre (NANOCAT), Universiti Malaya (UM), 50603 Kuala Lumpur (Malaysia); Rusop, M. [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor (Malaysia); NANO-SciTech Centre (NST), Institute of Science (IOS), Universiti Teknologi MARA UiTM, 40450 Shah Alam, Selangor (Malaysia)

    2014-01-05

    Highlights: • Minimum stress of highly c-axis oriented ZnO was grown at suitable deposition speed. • The ZnO crystal orientation was influenced by strain/stress of the film. • Minimum stress/strain of ZnO film leads to lower defects. • Bandgap and defects were closely intertwined with strain/stress. • We report additional optical and electrical properties based on deposition speed. -- Abstract: Zinc oxide (ZnO) thin films have been deposited onto glass substrates at various deposition speeds by a sonicated sol–gel dip-coating technique. This work studies the effects of deposition speed on the crystallisation behaviour and optical and electrical properties of the resulting films. X-ray diffraction (XRD) analysis showed that thin films were preferentially oriented along the (0 0 2) c-axis direction of the crystal. The transformation sequence of strain and stress effects in ZnO thin films has also been studied. The films deposited at a low deposition speed exhibited a large compressive stress of 0.78 GPa, which decreased to 0.43 GPa as the deposition speed increased to 40 mm/min. Interestingly, the enhancement in the crystallinity of these films led to a significant reduction in compressive stress. All films exhibited an average transmittance of greater than 90% in the visible region, with absorption edges at ∼380 nm. The photoluminescence (PL) measurements indicated that the intensity of the emission peaks varied significantly with deposition speed. The optical band gap energy (E{sub g}) was evaluated as 3.276–3.289 eV, which increased with decreasing compressive stress along the c-axis. The energy band gap of the resulting ZnO films was found to be strongly influenced by the preferred c-axis (0 0 2) orientation.

  19. Crystallographic control on early stages of cataclasis in carbonate fault gouges

    Science.gov (United States)

    Demurtas, Matteo; Smith, Steven A. F.; Fondriest, Michele; Spagnuolo, Elena; Di Toro, Giulio

    2017-04-01

    Carbonates are a recurring lithology in most of active seismic areas worldwide, such as the Apennines (Italy). Here, typical fault products are gouges and cataclasites made of mixtures of carbonate minerals (i.e., calcite and dolomite) that occasionally exhibit a foliation. Natural fault gouges often contain minerals with strong anisotropies, such as cleavage surfaces in phyllosilicates and carbonates. Therefore, the understanding of the role of such anisotropies during shearing is important to develop realistic microphysical models of brittle fragmentation and grain size reduction. Here we present results of microstructural and coupled EDS-EBSD (Energy Dispersive Spectroscopy - Electron Backscattered Diffraction) analysis on mixtures (50/50wt%) of calcite-dolomite gouges deformed experimentally in a rotary shear apparatus (SHIVA, INGV-Rome) at room temperature under constant normal stress of 17.5 MPa and slip rates of 30 µm/s to 1 m/s. The EDS-EBSD analysis was focused on the gouge layer underlying the slip zone, which has been previously demonstrated to accommodate low finite shear strain during deformation. At all investigated slip rates, calcite develops a crystallographic preferred orientation (CPO) on the (0001) plane, with the c-axis inclined subparallel to the principal stress and the [-1-120] direction forming a girdle perpendicular to it. Texture strength typically increases with slip rate and appears not to be influenced by the presence of water or foliation development in the gouge during deformation. Misorientation analysis suggests twinning as the principal crystallographic active deformation mechanism. Instead, dolomite grains do not develop a CPO. Microfractures are closely spaced, mainly oriented subparallel to the principal stress and rarely exploit calcite twin planes. The latter typically occur at high angle with respect to fractures, are oriented consistently with the sense of shear and almost orthogonal to the principal stress. Calcite grains

  20. The effect of crystallographic texture on stress-induced martensitic transformation in NiTi: A computational analysis.

    Science.gov (United States)

    Weafer, F M; Guo, Y; Bruzzi, M S

    2016-01-01

    NiTi׳s superelasticity is exploited in a number of biomedical devices, in particular self-expanding endovascular stents. These stents are often laser-cut from textured micro-tubing; texture is the distribution of crystallographic grain orientations in a polycrystalline material which has been experimentally shown to have a marked influence on mechanical properties. This study offers a computational examination into the effect of texture on the stress-induced martensite transformation (SIMT) in a micro-dogbone NiTi specimen subject to tensile loading. Finite Element Analysis (FEA) is employed to simulate the transformational behaviour of the specimen on a micro-scale level. To represent a realistic grain structure in the FEA model, grains present in a 200µm×290µm test site located at the centre edge of the specimen were identified using Scanning Electron Microscopy (SEM). Grains are assumed to have homogenous behaviour with properties varying according to their crystallographic orientation to the loading direction. Required material properties were extracted from uniaxial stress-strain curves of single crystals for each crystallographic orientation for input into the in-built UMAT/Nitinol. The orientation of each grain in the test site was identified using Electron Back-Scatter Diffraction (EBSD) techniques. In this way, a quantitative explanation is offered to the effect of crystallographic texture on SIMT. Finally, the evolution of grains in the specimen, during the transformation process, was experimentally investigated by means of an in-situ SEM tensile test.

  1. Independent preferences

    DEFF Research Database (Denmark)

    Vind, Karl

    1991-01-01

    A simple mathematical result characterizing a subset of a product set is proved and used to obtain additive representations of preferences. The additivity consequences of independence assumptions are obtained for preferences which are not total or transitive. This means that most of the economic...... theory based on additive preferences - expected utility, discounted utility - has been generalized to preferences which are not total or transitive. Other economic applications of the theorem are given...

  2. A Study on Human Oriented Autonomous Distributed Manufacturing System —Real-time Scheduling Method Based on Preference of Human Operators

    Science.gov (United States)

    Iwamura, Koji; Kuwahara, Shinya; Tanimizu, Yoshitaka; Sugimura, Nobuhiro

    Recently, new distributed architectures of manufacturing systems are proposed, aiming at realizing more flexible control structures of the manufacturing systems. Many researches have been carried out to deal with the distributed architectures for planning and control of the manufacturing systems. However, the human operators have not yet been discussed for the autonomous components of the distributed manufacturing systems. A real-time scheduling method is proposed, in this research, to select suitable combinations of the human operators, the resources and the jobs for the manufacturing processes. The proposed scheduling method consists of following three steps. In the first step, the human operators select their favorite manufacturing processes which they will carry out in the next time period, based on their preferences. In the second step, the machine tools and the jobs select suitable combinations for the next machining processes. In the third step, the automated guided vehicles and the jobs select suitable combinations for the next transportation processes. The second and third steps are carried out by using the utility value based method and the dispatching rule-based method proposed in the previous researches. Some case studies have been carried out to verify the effectiveness of the proposed method.

  3. Quantum crystallographic charge density of urea

    Directory of Open Access Journals (Sweden)

    Michael E. Wall

    2016-07-01

    Full Text Available Standard X-ray crystallography methods use free-atom models to calculate mean unit-cell charge densities. Real molecules, however, have shared charge that is not captured accurately using free-atom models. To address this limitation, a charge density model of crystalline urea was calculated using high-level quantum theory and was refined against publicly available ultra-high-resolution experimental Bragg data, including the effects of atomic displacement parameters. The resulting quantum crystallographic model was compared with models obtained using spherical atom or multipole methods. Despite using only the same number of free parameters as the spherical atom model, the agreement of the quantum model with the data is comparable to the multipole model. The static, theoretical crystalline charge density of the quantum model is distinct from the multipole model, indicating the quantum model provides substantially new information. Hydrogen thermal ellipsoids in the quantum model were very similar to those obtained using neutron crystallography, indicating that quantum crystallography can increase the accuracy of the X-ray crystallographic atomic displacement parameters. The results demonstrate the feasibility and benefits of integrating fully periodic quantum charge density calculations into ultra-high-resolution X-ray crystallographic model building and refinement.

  4. Crystallographic theory of the martensitic transformation

    Directory of Open Access Journals (Sweden)

    Edwar A. Torres-López

    2014-08-01

    Full Text Available The martensitic transformation is one of the most researched topics in the materials science during the 20th century. The second half of this century was mainly remembered by the development of several theories related with the kinetics of phase transformation, the mechanisms involved in the nucleation phenomenon, and the way as the crystallographic change is produced. In this paper are described the fundamental concepts that are defined in the crystallographic framework of the martensitic transformation. The study is focused on the application of the most outstanding crystallographic models: the Bain; the Wechsler, Lieberman & Read; and the Bowles & Mackenzie. The topic is presented based upon the particular features of the martensitic transformation, such as its non-diffusional character, type of interface between parent (austenite and product (martensite phases, the formation of substructural defects, and the shape change; all of these features are mathematically described by equations aimed to predict how the transformation will take place rather than to explain the actual movement of the atoms within the structure. This mathematical development is known as the Phenomenological Theory of Martensite Crystallography (PTMC.

  5. A preliminary neutron crystallographic study of thaumatin

    Energy Technology Data Exchange (ETDEWEB)

    Teixeira, Susana C. M. [ILL-EMBL Deuteration Laboratory, Partnership for Structural Biology, 6 Rue Jules Horowitz, 38042 Grenoble (France); Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom); Blakeley, Matthew P. [Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); Leal, Ricardo M. F. [ILL-EMBL Deuteration Laboratory, Partnership for Structural Biology, 6 Rue Jules Horowitz, 38042 Grenoble (France); Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom); ESRF, 6 Rue Jules Horowitz, BP-220, 38043 Grenoble (France); Mitchell, Edward P. [EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom); ESRF, 6 Rue Jules Horowitz, BP-220, 38043 Grenoble (France); Forsyth, V. Trevor, E-mail: tforsyth@ill.fr [ILL-EMBL Deuteration Laboratory, Partnership for Structural Biology, 6 Rue Jules Horowitz, 38042 Grenoble (France); Institut Laue Langevin, 6 Rue Jules Horowitz, 38042 Grenoble (France); EPSAM and ISTM, Keele University, Staffordshire ST5 5BG (United Kingdom)

    2008-05-01

    Preliminary neutron crystallographic data from the sweet protein thaumatin have been recorded using the LADI-III diffractometer at the Institut Laue Langevin (ILL). The results illustrate the feasibility of a full neutron structural analysis aimed at further understanding the molecular basis of the perception of sweet taste. Such an analysis will exploit the use of perdeuterated thaumatin. A preliminary neutron crystallographic study of the sweet protein thaumatin is presented. Large hydrogenated crystals were prepared in deuterated crystallization buffer using the gel-acupuncture method. Data were collected to a resolution of 2 Å on the LADI-III diffractometer at the Institut Laue Langevin (ILL). The results demonstrate the feasibility of a full neutron crystallographic analysis of this structure aimed at providing relevant information on the location of H atoms, the distribution of charge on the protein surface and localized water in the structure. This information will be of interest for understanding the specificity of thaumatin–receptor interactions and will contribute to further understanding of the molecular mechanisms underlying the perception of taste.

  6. Quantum crystallographic charge density of urea.

    Science.gov (United States)

    Wall, Michael E

    2016-07-01

    Standard X-ray crystallography methods use free-atom models to calculate mean unit-cell charge densities. Real molecules, however, have shared charge that is not captured accurately using free-atom models. To address this limitation, a charge density model of crystalline urea was calculated using high-level quantum theory and was refined against publicly available ultra-high-resolution experimental Bragg data, including the effects of atomic displacement parameters. The resulting quantum crystallographic model was compared with models obtained using spherical atom or multipole methods. Despite using only the same number of free parameters as the spherical atom model, the agreement of the quantum model with the data is comparable to the multipole model. The static, theoretical crystalline charge density of the quantum model is distinct from the multipole model, indicating the quantum model provides substantially new information. Hydrogen thermal ellipsoids in the quantum model were very similar to those obtained using neutron crystallography, indicating that quantum crystallography can increase the accuracy of the X-ray crystallographic atomic displacement parameters. The results demonstrate the feasibility and benefits of integrating fully periodic quantum charge density calculations into ultra-high-resolution X-ray crystallographic model building and refinement.

  7. Quantum crystallographic charge density of urea

    Science.gov (United States)

    Wall, Michael E.

    2016-01-01

    Standard X-ray crystallography methods use free-atom models to calculate mean unit-cell charge densities. Real molecules, however, have shared charge that is not captured accurately using free-atom models. To address this limitation, a charge density model of crystalline urea was calculated using high-level quantum theory and was refined against publicly available ultra-high-resolution experimental Bragg data, including the effects of atomic displacement parameters. The resulting quantum crystallographic model was compared with models obtained using spherical atom or multipole methods. Despite using only the same number of free parameters as the spherical atom model, the agreement of the quantum model with the data is comparable to the multipole model. The static, theoretical crystalline charge density of the quantum model is distinct from the multipole model, indicating the quantum model provides substantially new information. Hydrogen thermal ellipsoids in the quantum model were very similar to those obtained using neutron crystallography, indicating that quantum crystallography can increase the accuracy of the X-ray crystallographic atomic displacement parameters. The results demonstrate the feasibility and benefits of integrating fully periodic quantum charge density calculations into ultra-high-resolution X-ray crystallographic model building and refinement. PMID:27437111

  8. Collective preferences in strategic decisions.

    Science.gov (United States)

    Rose, Jo; Colman, Andrew M

    2007-12-01

    In the theories of team reasoning of Sugden and Bacharach, players are assumed to be motivated in some circumstances to maximize collective rather than individual utilities. An experiment was performed to assess whether preferences underlying such collective payoff maximization occur. An opportunistic sample of 50 undergraduate and graduate students, 7 men and 43 women ages 19 to 42 years (M= 23.0, SD=5.4), expressed preferences among the outcomes of strategic decisions presented in vignettes designed to engage social value orientations of individualism, altruism, competitiveness, equality seeking, or collective preferences. In the vignettes designed to engage collective preferences, and significantly less frequently in the other vignettes, preferences were biased toward outcomes maximizing collective payoffs, and respondents invariably gave team-reasoning explanations for their preferences. These results provide evidence for collective preferences according to theories of team reasoning and empirical support for one of the essential assumptions of these theories.

  9. Crystallographic dependence of CO activation on cobalt catalysts: HCP versus FCC.

    Science.gov (United States)

    Liu, Jin-Xun; Su, Hai-Yan; Sun, Da-Peng; Zhang, Bing-Yan; Li, Wei-Xue

    2013-11-06

    Identifying the structure sensitivity of catalysts in reactions, such as Fischer-Tropsch synthesis from CO and H2 over cobalt catalysts, is an important yet challenging issue in heterogeneous catalysis. Based on a first-principles kinetic study, we find for the first time that CO activation on hexagonal close-packed (HCP) Co not only has much higher intrinsic activity than that of face centered-cubic (FCC) Co but also prefers a different reaction route, i.e., direct dissociation with HCP Co but H-assisted dissociation on the FCC Co. The origin is identified from the formation of various denser yet favorable active sites on HCP Co not available for FCC Co, due to their distinct crystallographic structure and morphology. The great dependence of the activity on the crystallographic structure and morphology of the catalysts revealed here may open a new avenue for better, stable catalysts with maximum mass-specific reactivity.

  10. Auditor Preference

    OpenAIRE

    2012-01-01

    We analyze theoretically and empirically the effect of preference policies, which favor some auditors over others for reasons unrelated to the audit. For example, an auditee may prefer minority-owned auditors, all else equal. We construct an analytical model of the competitive bidding process for audit services. We show that preference policies can sometimes improve the audit procurement process by encouraging price concessions from non-preferenced auditors. We test model predictions in a set...

  11. World directory of crystallographers and of other scientists employing crystallographic methods

    CERN Document Server

    Filippini, G; Hashizume, H; Torriani, I; Duax, W

    1995-01-01

    The 9th edition of the World Directory of Crystallographers and of Other Scientists Employing Crystallographic Methods, which contains 7907 entries embracing 72 countries, differs considerably from the 8th edition, published in 1990. The content has been updated, and the methods used to acquire the information presented and to produce this new edition of the Directory have involved the latest advances in technology. The Directory is now also available as a regularly updated electronic database, accessible via e-mail, Telnet, Gopher, World-Wide Web, and Mosaic. Full details are given in an Appendix to the printed edition.

  12. Crystallographic similarity between the lath martensite and lower bainite in medium-carbon alloy steels

    Institute of Scientific and Technical Information of China (English)

    LIU Jiangwen; LUO Chengping; WU Dongxiao

    2005-01-01

    Progress in the crystallography of lath martensitic and lower bainitic transformations is briefly reviewed, followed by a presentation of the experimentally measured crystallographic characteristics of both lath martensite and lower bainite formed in mediumcarbon steels containing Si, Mn and Mo. It is found that the bainite plates relate to each other by a relative rotation of 54.7°or 60°about the normal to their common close-packed planes {110} b, which ensures a pseudo- {112}b twin relationship between two adjacent plates,and that all bainite variants formed in a single packet keep a unique G-T orientation relationship with the austenite matrix. These two types of OR of lower bainite are similar to that of the lath martensite, respectively. Furthermore, the measured habit planes of both the lower bainite and lath martensite are all {335} f type, which can verify the crystallographic similarity between the lath martensite and lower bainite.

  13. Crystallographic Analysis of Tapering of ADP Crystallites

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    On the basis of crystallographic characteristics of ADP (ammonium dihydrogen phosphate) crystals and the selected growth conditions, the growth habit of ADP crystals was studied. In comparison with pyramidal planes, the growth rate of prismatic faces is slower and more sensitive to the additives and impurities for ADP crystals. When the supersaturation is low, the advance of growth steps on prismatic face can be blocked by ethanol or impurities, the crystal morphology is changed from the tetragonal prism to shuttle (i.e., the tapered shape). The tapering formation of ADP crystallites was structurally studied in a novel view.

  14. Crystallographic Analysis of Isothermally Transformed Bainite in 0.2C-2.0Mn-1.5Si-0.6Cr Steel Using EBSD

    Institute of Scientific and Technical Information of China (English)

    Pasi P.Suikkanen; Cyril Cayron; Anthony J.DeArdo; L.Pentti Karjalainen

    2013-01-01

    The crystallography of bainite,transformed isothermally at 450 ℃ in 0.2C-2.0Mn-1.5Si-O.6Cr steel,was investigated by electron backscatter diffraction (EBSD) analysis.The orientation relationship (OR) was found to be closer to Nishiyama-Wassermann (N-W) than Kurdjumov-Sachs orientation relationship.Bainite microstructure consisted of parallel laths forming a morphological packet structure.Typically,there were three different lath orientations in a morphological packet.These orientations were dictated by a three specific N-W OR variants sharing the same {111} austenite plane.A packet of bainite laths with common {111}austenite plane was termed as crystallographic packet.Generally,the crystallographic packet size corresponded to the morphological packet size.Locally,crystallographic packets with only two dominant orientations were observed.This indicates strong local variant selection during isothermal bainite transformation.The relative orientation between the variants in crystallographic packets was found to be near 60°/<110>.This appears to explain the strong peak observed in the grain boundary misorientation distribution near 60°.Bainite also contained pronounced fraction of boundaries with their misorientation in the range of 2.5°-8° with quite widely dispersed rotation angles.Spatially these boundaries were found to locate inside the bainite laths,forming lath-like sub-grains.

  15. Orbits of crystallographic embedding of non-crystallographic groups and applications to virology.

    Science.gov (United States)

    Twarock, Reidun; Valiunas, Motiejus; Zappa, Emilio

    2015-11-01

    The architecture of infinite structures with non-crystallographic symmetries can be modelled via aperiodic tilings, but a systematic construction method for finite structures with non-crystallographic symmetry at different radial levels is still lacking. This paper presents a group theoretical method for the construction of finite nested point sets with non-crystallographic symmetry. Akin to the construction of quasicrystals, a non-crystallographic group G is embedded into the point group P of a higher-dimensional lattice and the chains of all G-containing subgroups are constructed. The orbits of lattice points under such subgroups are determined, and it is shown that their projection into a lower-dimensional G-invariant subspace consists of nested point sets with G-symmetry at each radial level. The number of different radial levels is bounded by the index of G in the subgroup of P. In the case of icosahedral symmetry, all subgroup chains are determined explicitly and it is illustrated that these point sets in projection provide blueprints that approximate the organization of simple viral capsids, encoding information on the structural organization of capsid proteins and the genomic material collectively, based on two case studies. Contrary to the affine extensions previously introduced, these orbits endow virus architecture with an underlying finite group structure, which lends itself better to the modelling of dynamic properties than its infinite-dimensional counterpart.

  16. Collaborative annotation of 3D crystallographic models.

    Science.gov (United States)

    Hunter, J; Henderson, M; Khan, I

    2007-01-01

    This paper describes the AnnoCryst system-a tool that was designed to enable authenticated collaborators to share online discussions about 3D crystallographic structures through the asynchronous attachment, storage, and retrieval of annotations. Annotations are personal comments, interpretations, questions, assessments, or references that can be attached to files, data, digital objects, or Web pages. The AnnoCryst system enables annotations to be attached to 3D crystallographic models retrieved from either private local repositories (e.g., Fedora) or public online databases (e.g., Protein Data Bank or Inorganic Crystal Structure Database) via a Web browser. The system uses the Jmol plugin for viewing and manipulating the 3D crystal structures but extends Jmol by providing an additional interface through which annotations can be created, attached, stored, searched, browsed, and retrieved. The annotations are stored on a standardized Web annotation server (Annotea), which has been extended to support 3D macromolecular structures. Finally, the system is embedded within a security framework that is capable of authenticating users and restricting access only to trusted colleagues.

  17. Preference Learning

    CERN Document Server

    Furnkranz, Johannes

    2011-01-01

    The topic of preferences is a new branch of machine learning and data mining, and it has attracted considerable attention in artificial intelligence research in previous years. It involves learning from observations that reveal information about the preferences of an individual or a class of individuals. Representing and processing knowledge in terms of preferences is appealing as it allows one to specify desires in a declarative way, to combine qualitative and quantitative modes of reasoning, and to deal with inconsistencies and exceptions in a flexible manner. And, generalizing beyond traini

  18. Nanocrystalline materials: recent advances in crystallographic characterization techniques

    Directory of Open Access Journals (Sweden)

    Emilie Ringe

    2014-11-01

    Full Text Available Most properties of nanocrystalline materials are shape-dependent, providing their exquisite tunability in optical, mechanical, electronic and catalytic properties. An example of the former is localized surface plasmon resonance (LSPR, the coherent oscillation of conduction electrons in metals that can be excited by the electric field of light; this resonance frequency is highly dependent on both the size and shape of a nanocrystal. An example of the latter is the marked difference in catalytic activity observed for different Pd nanoparticles. Such examples highlight the importance of particle shape in nanocrystalline materials and their practical applications. However, one may ask `how are nanoshapes created?', `how does the shape relate to the atomic packing and crystallography of the material?', `how can we control and characterize the external shape and crystal structure of such small nanocrystals?'. This feature article aims to give the reader an overview of important techniques, concepts and recent advances related to these questions. Nucleation, growth and how seed crystallography influences the final synthesis product are discussed, followed by shape prediction models based on seed crystallography and thermodynamic or kinetic parameters. The crystallographic implications of epitaxy and orientation in multilayered, core-shell nanoparticles are overviewed, and, finally, the development and implications of novel, spatially resolved analysis tools are discussed.

  19. Nanocrystalline materials: recent advances in crystallographic characterization techniques.

    Science.gov (United States)

    Ringe, Emilie

    2014-11-01

    Most properties of nanocrystalline materials are shape-dependent, providing their exquisite tunability in optical, mechanical, electronic and catalytic properties. An example of the former is localized surface plasmon resonance (LSPR), the coherent oscillation of conduction electrons in metals that can be excited by the electric field of light; this resonance frequency is highly dependent on both the size and shape of a nanocrystal. An example of the latter is the marked difference in catalytic activity observed for different Pd nanoparticles. Such examples highlight the importance of particle shape in nanocrystalline materials and their practical applications. However, one may ask 'how are nanoshapes created?', 'how does the shape relate to the atomic packing and crystallography of the material?', 'how can we control and characterize the external shape and crystal structure of such small nanocrystals?'. This feature article aims to give the reader an overview of important techniques, concepts and recent advances related to these questions. Nucleation, growth and how seed crystallography influences the final synthesis product are discussed, followed by shape prediction models based on seed crystallography and thermodynamic or kinetic parameters. The crystallographic implications of epitaxy and orientation in multilayered, core-shell nanoparticles are overviewed, and, finally, the development and implications of novel, spatially resolved analysis tools are discussed.

  20. Nanocrystalline materials: recent advances in crystallographic characterization techniques

    Science.gov (United States)

    Ringe, Emilie

    2014-01-01

    Most properties of nanocrystalline materials are shape-dependent, providing their exquisite tunability in optical, mechanical, electronic and catalytic properties. An example of the former is localized surface plasmon resonance (LSPR), the coherent oscillation of conduction electrons in metals that can be excited by the electric field of light; this resonance frequency is highly dependent on both the size and shape of a nanocrystal. An example of the latter is the marked difference in catalytic activity observed for different Pd nanoparticles. Such examples highlight the importance of particle shape in nanocrystalline materials and their practical applications. However, one may ask ‘how are nanoshapes created?’, ‘how does the shape relate to the atomic packing and crystallography of the material?’, ‘how can we control and characterize the external shape and crystal structure of such small nanocrystals?’. This feature article aims to give the reader an overview of important techniques, concepts and recent advances related to these questions. Nucleation, growth and how seed crystallography influences the final synthesis product are discussed, followed by shape prediction models based on seed crystallography and thermodynamic or kinetic parameters. The crystallographic implications of epitaxy and orientation in multilayered, core-shell nanoparticles are overviewed, and, finally, the development and implications of novel, spatially resolved analysis tools are discussed. PMID:25485133

  1. Crystallographic Analysis of Martensite in 0.2C-2.0Mn-1.5Si-0.6Cr Steel using EBSD

    Institute of Scientific and Technical Information of China (English)

    Pasi P. Suikkanen; Cyril Cayron; Anthony J. DeArdo; L Pentti Karjalainen

    2011-01-01

    The crystallography of martensite formed in 0.2C-2.0Mn-1,5Si-0.6Cr steel was studied using the electron backscattered diffraction (EBSD) technique. The results showed that the observed orientation relationship (OR) was closer to that of Nishiyama-Wassermann (N-W) than Kurdjumov-Sachs. The martensite consisted of parallel laths forming morphological packets. Typically, there were three different lath orientations in a morphological packet consisting of three specific N-W OR variants sharing the same {111} austenite plane. A packet of martensite laths with a common {111} austenite plane was termed a crystallographic packet. Generally, the crystallographic packet size corresponded to the morphological packet size, but occasionally the morphological packet was found to consist of two or more crystallographic packets. Therefore, the crystallographic packet size appeared to be finer than the morphological packet size. The relative orientation between the variants in crystallographic packets was found to be near 60°〈110〉, which explains the strong peak observed near 60° in the grain boundary misorientation distribution. Martensite also contained a high fraction of boundaries with a misorientation in the range 2.5-8°. Typically these boundaries were found to be located inside the martensite laths forming sub-laths.

  2. X-ray crystallographic studies of metalloproteins.

    Science.gov (United States)

    Volbeda, Anne

    2014-01-01

    Many proteins require metals for their physiological function. In combination with spectroscopic characterizations, X-ray crystallography is a very powerful method to correlate the function of protein-bound metal sites with their structure. Due to their special X-ray scattering properties, specific metals may be located in metalloprotein structures and eventually used for phasing the diffracted X-rays by the method of Multi-wavelength Anomalous Dispersion (MAD). How this is done is the principle subject of this chapter. Attention is also given to the crystallographic characterization of different oxidation states of redox active metals and to the complication of structural changes that may be induced by X-ray irradiation of protein crystals.

  3. Crystallographic dependence of photocatalytic activity of WO3 thin films prepared by molecular beam epitaxy.

    Science.gov (United States)

    Li, Guoqiang; Varga, Tamas; Yan, Pengfei; Wang, Zhiguo; Wang, Chongmin; Chambers, Scott A; Du, Yingge

    2015-06-21

    We investigated the impact of crystallographic orientation on the photocatalytic activity of single crystalline WO3 thin films prepared by molecular beam epitaxy on the photodegradation of rhodamine B (RhB). A clear effect is observed, with (111) being the most reactive surface, followed by (110) and (001). Photoreactivity is directly correlated with the surface free energy determined by density functional theory calculations. The RhB photodegradation mechanism is found to involve hydroxyl radicals in solution formed from photo-generated holes and differs from previous studies performed on nanoparticles and composites.

  4. Social preferences

    DEFF Research Database (Denmark)

    Gulløv, Eva

    2014-01-01

    The focus of this article is social divisions among preschool children in daycare centers. Based on ethnographic fieldwork in three daycare centers in Denmark, the analysis concerns young children’s social preferences. The ethnographic material shows that despite an explicit political ambition...... of daycares as means for social and cultural integration, lines of division do exist amongst the children. Such divisions are established in the daily interactions of the daycare, but they also reflect those of the broader society. With a focus on children’s interactions and social preferences, the material...

  5. Crystallographic dependent in-situ CBr4 selective nano-area etching and local regrowth of InP/InGaAs by MOVPE

    DEFF Research Database (Denmark)

    Kuznetsova, Nadezda; Kulkova, Irina; Semenova, Elizaveta;

    2014-01-01

    Selective area etching and growth in the metalorganic vapor phase epitaxy (MOVPE) reactor on nano-scale structures have been examined. Using different mask orientations, crystallographic dependent etching of InP can be observed when carbon tetrabromide (CBr4) is used as an etchant. Scanning Elect...

  6. Calculation of Crystallographic Texture of BCC Steels During Cold Rolling

    Science.gov (United States)

    Das, Arpan

    2017-05-01

    BCC alloys commonly tend to develop strong fibre textures and often represent as isointensity diagrams in φ 1 sections or by fibre diagrams. Alpha fibre in bcc steels is generally characterised by crystallographic axis parallel to the rolling direction. The objective of present research is to correlate carbon content, carbide dispersion, rolling reduction, Euler angles (ϕ) (when φ 1 = 0° and φ 2 = 45° along alpha fibre) and the resulting alpha fibre texture orientation intensity. In the present research, Bayesian neural computation has been employed to correlate these and compare with the existing feed-forward neural network model comprehensively. Excellent match to the measured texture data within the bounding box of texture training data set has been already predicted through the feed-forward neural network model by other researchers. Feed-forward neural network prediction outside the bounds of training texture data showed deviations from the expected values. Currently, Bayesian computation has been similarly applied to confirm that the predictions are reasonable in the context of basic metallurgical principles, and matched better outside the bounds of training texture data set than the reported feed-forward neural network. Bayesian computation puts error bars on predicted values and allows significance of each individual parameters to be estimated. Additionally, it is also possible by Bayesian computation to estimate the isolated influence of particular variable such as carbon concentration, which exactly cannot in practice be varied independently. This shows the ability of the Bayesian neural network to examine the new phenomenon in situations where the data cannot be accessed through experiments.

  7. Social preferences

    DEFF Research Database (Denmark)

    Gulløv, Eva

    2014-01-01

    indicates that children’s choices of playmates run along lines of ethnic and class divisions. The article will address this pattern and analyze its causes in order to understand why such lines of divisions are to be found in an institutional context designed to overcome social inequality and prevent social......The focus of this article is social divisions among preschool children in daycare centers. Based on ethnographic fieldwork in three daycare centers in Denmark, the analysis concerns young children’s social preferences. The ethnographic material shows that despite an explicit political ambition...... of daycares as means for social and cultural integration, lines of division do exist amongst the children. Such divisions are established in the daily interactions of the daycare, but they also reflect those of the broader society. With a focus on children’s interactions and social preferences, the material...

  8. Sequential effects in preference decision: Prior preference assimilates current preference.

    Science.gov (United States)

    Chang, Seah; Kim, Chai-Youn; Cho, Yang Seok

    2017-01-01

    An important factor affecting preference formation is the context in which that preference decision takes place. The current research examined whether one's preference formed for a previously presented stimulus influences the processing of a subsequent preference decision, henceforth referred to as the preference sequence effect. Using a novel sequential rating/judgment paradigm, the present study demonstrated the presence of a preference sequence effect using artistic photographs and face stimuli: A neutral stimulus was preferred more following a preferable stimulus than a less preferable stimulus. Furthermore, a similar trend was found even when the potential influence of response bias was controlled. These results suggest that an assimilative sequential effect exists even when sequential judgments are made solely based on one's subjective feeling; preference formed for a preceding stimulus modulates preference for a subsequent stimulus. This implies the need for a consideration of trial sequence as a factor creating a psychological context affecting the subsequent preference decisions.

  9. Structural Investigations of Surfaces and Orientation-SpecificPhenomena in Nanocrystals and Their Assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Aruguete, Deborah Michiko [Univ. of California, Berkeley, CA (United States)

    2006-01-01

    examined with transmission electron microscopy (TEM) and selected-area electron diffraction (SAED). SAED patterns from multilayered assemblies show that the nanocrystals have preferred crystallographic orientations. It is proposed that the nanocrystals are organized in a vortex-like or ''loop-closing'' arrangement, possibly due to magnetism. SAED and dark-field imaging used to investigate this hypothesis are presented, along with the data analysis. The effects of magnetism and nanocrystal faceting are discussed.

  10. Crystallographic interpretation of Galois symmetries for magnetic pentagonal ring

    Science.gov (United States)

    Milewski, J.; Lulek, T.; Łabuz, M.

    2017-03-01

    Galois symmetry of exact Bethe Ansatz eigenstates for the magnetic pentagonal ring within the XXX model are investigated by a comparison with crystallographic constructions of space groups. It follows that the arithmetic symmetry of Bethe parameters for the interior of the Brillouin zone admits crystallographic interpretation, in terms of the periodic square Z2 ×Z2 , that is the two-dimensional crystal lattice with Born-Karman period two in both directions.

  11. Anisotropic grain morphology, crystallographic texture and their implications for flux pinning mechanisms in MgB{sub 2} pellets, filaments and thin films

    Energy Technology Data Exchange (ETDEWEB)

    Song Xueyan [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, WI (United States) and Applied Superconductivity Center, University of Wisconsin-Madison, Madison, WI (United States)]. E-mail: xsong@facstaff.wisc.edu; Babcock, S.E.; Eom, C.B.; Larbalestier, D.C. [Department of Materials Science and Engineering, University of Wisconsin-Madison, Madison, WI (United States); Applied Superconductivity Center, University of Wisconsin-Madison, Madison, WI (United States); Regan, K.A.; Cava, R.J. [Department of Chemistry, Princeton University, Princeton, NJ (United States); Bud' Ko, S.L.; Canfield, P.C.; Finnemore, D.K. [Department of Physics and Astronomy, Iowa State University, Ames, IA (United States)

    2002-04-01

    Grain morphology and crystallographic texture were investigated by electron microscopy in four different polycrystalline forms of superconducting MgB{sub 2}. The materials included a hot-pressed sintered MgB{sub 2} pellet, a pellet reacted in situ from Mg and B, an in situ reacted MgB{sub 2} filament and a pulsed-laser-deposited thin film grown on a single crystalline [111] oriented SrTiO{sub 3} substrate. Thick plate-shaped grains with an aspect ratio of {approx}3 and large faces parallel to (0001) planes dominated the microstructure in all four types of sample. The intermediate-sized plate-shaped grains (0.1{mu}mx0.3{mu}m on average) in the electromagnetically most homogeneous parts of the hot-pressed pellets were strongly facetted, but not textured. Large (3-5 {mu}m) plate-shaped grains were seen in the pellet reacted directly from stoichiometric Mg and B. A tendency for parallel alignment of the [0001] axes of the considerably larger grains ({approx}0.25{mu}mx1{mu}m) in the filament was observed near its W core, but degradation of this texture away from the core was apparent. The very small grains ({approx}10 nm) of the thin film possessed a well-defined fibre texture with [0001] parallel to the film normal and no preferred orientation in the plane of the film. Electrical resistivity of the finest grain samples was some 10{sup 3} times higher than the largest grain sample and their critical current density about one order of magnitude higher. We conclude that, in contrast to the cuprate-based high-T{sub c} superconductors, grain boundaries do not limit the critical current density of polycrystalline MgB{sub 2} and indeed act as flux-pinning centres, which enhance the critical current density. (author)

  12. Preparing polished crystal slices with high precision orientation

    DEFF Research Database (Denmark)

    Mathiesen, S. Ipsen; Gerward, Leif; Pedersen, O.

    1974-01-01

    A polishing procedure is described which utilizes a high precision Laue technique for crystal orientation. Crystal slices with their final polished surfaces parallel to a crystallographic plane within 0.02° can be prepared. ©1974 The American Institute of Physics......A polishing procedure is described which utilizes a high precision Laue technique for crystal orientation. Crystal slices with their final polished surfaces parallel to a crystallographic plane within 0.02° can be prepared. ©1974 The American Institute of Physics...

  13. Thermomolecular orientation of nonpolar fluids.

    Science.gov (United States)

    Römer, Frank; Bresme, Fernando; Muscatello, Jordan; Bedeaux, Dick; Rubí, J Miguel

    2012-03-09

    We investigate the response of molecular fluids to temperature gradients. Using nonequilibrium molecular dynamics computer simulations we show that nonpolar diatomic fluids adopt a preferred orientation as a response to a temperature gradient. We find that the magnitude of this thermomolecular orientation effect is proportional to the strength of the temperature gradient and the degree of molecular anisotropy, as defined by the different size or mass of the molecular atomic sites. We show that the preferred orientation of the molecules follows the same trends observed in the Soret effect of binary mixtures. We argue this is a general effect that should be observed in a wide range of length scales.

  14. Geometry and crystallographic configuration of grain boundaries

    Science.gov (United States)

    Eichler, Jan; Weikusat, Ilka; Kipfstuhl, Sepp; Binder, Tobias

    2015-04-01

    Ice cores provide a unique opportunity to study fundamental mechanisms which control the internal flow of ice sheets. Different kinds of deformation processes acting on the micro-scale are responsible for the viscoplastic behavior on large scale. Careful interpretation of microstructural features such as grain size, shape, lattice orientation and the occurrence of subgrain boundaries can help us to follow these processes and to improve our understanding of ice rheology. Polarized light microscopy experienced a quick development in the last decade. A new generation of automatic fabric analyzers enables to measure c-axis orientations in µm-resolution. This high amount and quality of fabric data motivates to apply digital-image-processing routines (DIP) for the recognition and quantification of microstructural patterns. Here we present a study on grain boundaries based on the acquisition of more than 700 fabric images recorded along the NEEM ice core (Greenland). Geometrical characteristics of grain boundaries are studied as well as their cross-sectional orientations in relation to the c-axis orientations of the corresponding adjacent grains. We could follow the evolution from the initial N-type and P-type low-angle boundaries (Weikusat et al., 2011) to high angle boundaries during rotation recrystallization. In agreement with some previous studies we confirm that the established three-stage-recrystallization model may be an oversimplification. According to our results, rotation recrystallization as well as grain boundary migration are actually present in all depths with varying intensities at NEEM. I. Weikusat, A. Miyamoto, S. H. Faria, S. Kipfstuhl, N. Azuma, and T. Hondoh: Subgrain boundaries in Antarctic ice quantified by X-ray Laue diffraction. J. Glaciol., 57(201):85-94, 2011. doi: 10013/epic.36402.

  15. Danish orientalism

    National Research Council Canada - National Science Library

    Zerlang, Martin

    2006-01-01

    Orientalism became an important current in nineteenth-century Danish culture, but although it was contemporaneous with the orientalism of the leading European nations - Great Britain, France, Germany...

  16. Structural analysis and shape-preferred orientation determination of the mélange facies in the Chañaral mélange, Las Tórtolas Formation, Coastal Cordillera, northern Chile

    Science.gov (United States)

    Fuentes, Paulina; Díaz-Alvarado, Juan; Fernández, Carlos; Díaz-Azpiroz, Manuel; Rodríguez, Natalia

    2016-04-01

    . The intensity of deformational process is reflected in the high aspect ratios yielded by the quartzite constrictive (L) and flattened (L-S) object axes. Meso-scale shape preferred orientation (SPO) has been compared with quartz microtextures in quartzite blocks, resulting aspect ratios considerably lower than those obtained from the mesoscopic fabric. Main deformation mechanism observed in quartz microtextures are bulging-subgrain rotation recrystallization and dissolution-precipitation creep for pure and impure quartzites respectively. The temperatures deduced from these microtextures are between 350 and 400 °C, which coincides with the greenschists facies metamorphism observed in the Las Tórtolas and the mélange facies. Extremely dissociation between micro- and meso-scale deformation could be generated by dissolution at high differential stress in the boundaries of the quartzite layers and precipitation at low differential stress parts, which would increase the aspect ratio of the lenses whereas internally, quartz would have remained virtually unstrained. We propose here a tectonic setting for the Chañaral mélange formation based on the geodynamic evolution of the western active margin of South America during Late Paleozoic to Early Jurassic. Thus, the study area is located in a LT-HP zone of an accretionary complex, where rocks from the subduction channel (mélange facies) and the basal domain of the prism (brittle-ductile domain of the Las Tórtolas Formation) are in contact through the Infieles fault.

  17. Conformation-changing aggregation in hydroxyacetone: a combined low-temperature FTIR, jet, and crystallographic study.

    Science.gov (United States)

    Sharma, Archna; Reva, Igor; Fausto, Rui; Hesse, Susanne; Xue, Zhifeng; Suhm, Martin A; Nayak, Susanta K; Sathishkumar, Ranganthan; Pal, Rumpa; Row, Tayur N Guru

    2011-12-21

    Aggregation in hydroxyacetone (HA) is studied using low-temperature FTIR, supersonic jet expansion, and X-ray crystallographic (in situ cryocrystallization) techniques. Along with quantum chemical methods (MP2 and DFT), the experiments unravel the conformational preferences of HA upon aggregation to dimers and oligomers. The O-H···O═C intramolecular hydrogen bond present in the gas-phase monomer partially opens upon aggregation in supersonic expansions, giving rise to intermolecular cooperatively enhanced O-H···O-H hydrogen bonds in competition with isolated O-H···O═C hydrogen bonds. On the other hand, low-temperature IR studies on the neat solid and X-ray crystallographic data reveal that HA undergoes profound conformational changes upon crystallization, with the HOCC dihedral angle changing from ~0° in the gas phase to ~180° in the crystalline phase, hence giving rise to a completely new conformation. These conclusions are supported by theoretical calculations performed on the geometry derived from the crystalline phase. © 2011 American Chemical Society

  18. Role of crystallographic anisotropy in the formation of surface layers of single NiTi crystals after ion-plasma alloying

    Energy Technology Data Exchange (ETDEWEB)

    Poletika, T. M., E-mail: poletm@ispms.tsc.ru; Girsova, S. L., E-mail: llm@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Meisner, L. L., E-mail: girs@ispms.tsc.ru; Meisner, S. N., E-mail: msn@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation); Shulepov, I. A., E-mail: iashulepov@tpu.ru [National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation)

    2015-10-27

    The structure of the surface and near-surface layers of single crystals of NiTi, differently oriented relative to the direction of ion beam treatment was investigated. The role of the crystallographic orientation in formation of structure of surface layers after ion-plasma alloying was revealed. It was found that the orientation effects of selective sputtering and channeling determine the thickness of the oxide and amorphous layers, the depth of penetration of ions and impurities, the distribution of Ni with depth.

  19. Platinum Group Thiophenoxyimine Complexes: Syntheses,Crystallographic and Computational Studies of Structural Properties

    Energy Technology Data Exchange (ETDEWEB)

    Krinsky, Jamin L.; Arnold, John; Bergman, Robert G.

    2006-10-03

    Monomeric thiosalicylaldiminate complexes of rhodium(I) and iridium(I) were prepared by ligand transfer from the homoleptic zinc(II) species. In the presence of strongly donating ligands, the iridium complexes undergo insertion of the metal into the imine carbon-hydrogen bond. Thiophenoxyketimines were prepared by non-templated reaction of o-mercaptoacetophenone with anilines, and were complexed with rhodium(I), iridium(I), nickel(II) and platinum(II). X-ray crystallographic studies showed that while the thiosalicylaldiminate complexes display planar ligand conformations, those of the thiophenoxyketiminates are strongly distorted. Results of a computational study were consistent with a steric-strain interpretation of the difference in preferred ligand geometries.

  20. Erbium-ion implantation into various crystallographic cuts of Al2O3

    Science.gov (United States)

    Nekvindova, P.; Mackova, A.; Malinsky, P.; Cajzl, J.; Svecova, B.; Oswald, J.; Wilhelm, R. A.

    2015-12-01

    This paper reports on the importance of crystallographic cuts with a different orientation on the luminescent properties and structural changes of Al2O3 implanted with Er+ ions at 190 keV and with a fluence of 1.0 × 1016 cm-2. Post-implantation annealing at 1000 °C in oxygen atmosphere was also done. The chemical compositions and erbium concentration-depth profiles of implanted layers were studied by Rutherford Backscattering Spectrometry (RBS) and compared to SRIM simulations. The same value of the maximum erbium concentration (up to 2 at.%) was observed at a depth of about 40 nm for all crystallographic cuts. The structural properties of the prepared layers were characterised by RBS/channelling. The relative amount of disordered atoms of 70-80% was observed in the prepared implanted layers and discussed for various cuts. It has been found that erbium is positioned randomly in the Al2O3 crystalline matrix, and no preferential positions appeared even after the annealing procedure. Erbium luminescence properties were measured in the wavelength range of 1440-1650 nm for all samples. As-implanted Al2O3 samples had a significant luminescence band at 1530 nm. The best luminescence was repeatedly observed in the cut of Al2O3. The annealing procedure significantly improved the luminescent properties.

  1. Crystallographic and electronic properties of AlCrN films that absorb visible light

    Science.gov (United States)

    Tatemizo, N.; Imada, S.; Miura, Y.; Nishio, K.; Isshiki, T.

    2017-05-01

    We investigate the crystallographic and electronic properties of wurtzite Cr-doped AlN (AlCrN) films (Cr ≤12.0%) that absorb visible light. We confirmed that the films consist of wurtzite columnar single crystals that are densely packed, c-axis oriented, and exhibit a random rotation along the a-axis in plane by using transmission electron microscopy. The oxidation state of Cr was found to be 3+ using Cr K-edge X-ray absorption near edge structure, which implies that Cr can be a substitute for Al3+ in AlN. The first nearest neighbor distances estimated using Cr K-edge extended X-ray absorption fine structure (EXAFS) were found to be nearly isotropic for incident light with electric fields that are parallel and perpendicular to the plane. The results of ab initio lattice relaxation calculations for the model of wurtzite Al1-xCrxN supercell where Cr replaces Al support the EXAFS results. The calculations for the model showed that additional energy bands are formed in the band gap of AlN, in which the Fermi energy (EF) is present. As expected from the calculation results, the electrical conductivity increases with increase in the Cr concentration, implying that the density of states at EF increases monotonically. From these results, we can conclude that AlCrN films are an intermediate band material with respect to their crystallographic and electric properties.

  2. Determination of precise crystallographic directions for mask alignment in wet bulk micromachining for MEMS

    Science.gov (United States)

    Singh, Sajal Sagar; Pal, Prem; Pandey, Ashok Kumar; Xing, Yan; Sato, Kazuo

    2016-12-01

    In wet bulk micromachining, the etching characteristics are orientation dependent. As a result, prolonged etching of mask openings of any geometric shape on both Si{100} and Si{110} wafers results in a structure defined by the slowest etching planes. In order to fabricate microstructures with high dimensional accuracy, it is vital to align the mask edges along the crystal directions comprising of these slowest etching planes. Thus, precise alignment of mask edges is important in micro/nano fabrication. As a result, the determination of accurate crystal directions is of utmost importance and is in fact the first step to ensure dimensionally accurate microstructures for improved performance. In this review article, we have presented a comprehensive analysis of different techniques to precisely determine the crystallographic directions. We have covered various techniques proposed in the span of more than two decades to determine the crystallographic directions on both Si{100} and Si{110} wafers. Apart from a detailed discussion of each technique along with their design and implementation, we have provided a critical analysis of the associated constraints, benefits and shortcomings. We have also summed up the critical aspects of each technique and presented in a tabular format for easy reference for readers. This review article comprises of an exhaustive discussion and is a handy reference for researchers who are new in the field of wet anisotropic etching or who want to get abreast with the techniques of determination of crystal directions.

  3. Crystallographic Topology 2: Overview and Work in Progress

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, C.K.

    1999-08-01

    This overview describes an application of contemporary geometric topology and stochastic process concepts to structural crystallography. In this application, crystallographic groups become orbifolds, crystal structures become Morse functions on orbifolds, and vibrating atoms in a crystal become vector valued Gaussian measures with the Radon-Nikodym property. Intended crystallographic benefits include new methods for visualization of space groups and crystal structures, analysis of the thermal motion patterns seen in ORTEP drawings, and a classification scheme for crystal structures based on their Heegaard splitting properties.

  4. Deformation microstructure and orientation of F.C.C. crystals

    DEFF Research Database (Denmark)

    Liu, Q.; Hansen, N.

    1995-01-01

    The effect of crystallographic orientation on the microstructural evolution in f.c.c. metals with medium to high stacking fault energy is analyzed. This analysis is based on a literature review of the behaviour of single crystals and polycrystals supplemented with an experimental study of cold...

  5. The effect of magnetic annealing on crystallographic texture and magnetic properties of Fe-2.6% Si

    Energy Technology Data Exchange (ETDEWEB)

    Salih, M.Z., E-mail: mohammedzs2007@hotmail.com [Institut für Werkstoffkunde und Werkstofftechnik, TU Clausthal, Agricolastraße 6, D-38678 Clausthal-Zellerfeld (Germany); Uhlarz, M. [Dresden High Magnetic Field Laboratory (HLD), Helmholtz-Zentrum Dresden-Rossendorf, Bautzner Landstraße 400, D-01328 Dresden (Germany); Pyczak, F. [Instiute of Materials Research, Helmholtz-Zentrum Geesthacht, Max-Planck-Straße 1, D-21502 Geesthacht (Germany); Brokmeier, H.-G. [Institut für Werkstoffkunde und Werkstofftechnik, TU Clausthal, Agricolastraße 6, D-38678 Clausthal-Zellerfeld (Germany); Instiute of Materials Research, Helmholtz-Zentrum Geesthacht, Max-Planck-Straße 1, D-21502 Geesthacht (Germany); Weidenfeller, B. [Institut für Elektrochemie, Abteilung für Materialwissenschaft, Arnold-Sommerfeld-Straße 6, D-38678 Clausthal-Zellerfeld (Germany); Al-hamdany, N. [Institut für Werkstoffkunde und Werkstofftechnik, TU Clausthal, Agricolastraße 6, D-38678 Clausthal-Zellerfeld (Germany); Gan, W.M. [Instiute of Materials Research, Helmholtz-Zentrum Geesthacht, Max-Planck-Straße 1, D-21502 Geesthacht (Germany); Zhong, Z.Y. [Institut für Werkstoffkunde und Werkstofftechnik, TU Clausthal, Agricolastraße 6, D-38678 Clausthal-Zellerfeld (Germany); Schell, N. [Instiute of Materials Research, Helmholtz-Zentrum Geesthacht, Max-Planck-Straße 1, D-21502 Geesthacht (Germany)

    2015-05-01

    The effect of magnetic annealing on crystallographic texture, microstructure, defects density and magnetic properties of a Fe-2.6% Si steel has been analyzed. After two stage cold rolling (75% and 60% cold rolled) with intermediate annealing process at (600 °C/1 h) the sample annealed at 600 °C for one hour during which different magnetic field of 0, 7 and 14 T were applied has been investigated. The effect of defects density after cold rolling process on the recrystallization texture and magnetic properties was characterized. Heat treatments under a high external field of 14 T show a drastic improvement of the magnetic properties such as significantly increased permeability. Neutron diffraction measurements were preferred for measurement of the bulk sample texture so that sufficient grain statistics were obtained. Because of its small wavelength (0.05–0.2 Å) Synchrotron diffraction with high photon energy was used to evaluate the defects density by a modified Williamson–Hall plot. - Highlights: • We show the effect of the magnetic annealing after intermediate cold rolling on the crystallographic texture and magnetic properties. • Due the coarse grained we used Neutron diffraction for texture measurement. • We used hysteresis recorder to measure the magnetic properties. • The magnetic annealing leads to drastic improvements of the magnetic properties such as significantly increased permeability. • We show the effect of defect density on the crystallographic texture and magnetic properties.

  6. Expressing Preferences using Preference Set Constraint Atoms

    CERN Document Server

    Brik, Alex

    2012-01-01

    This paper introduces an extension of Answer Set Programming called Preference Set Constraint Programming which is a convenient and general formalism to reason with preferences. PSC programming extends Set Constraint Programming introduced by Marek and Remmel (Marek and Remmel 2004) by introducing two types of preference set constraint atoms, measure preference set constraint atoms and pre-ordered preference set constraint atoms, which are extensions of set constraint atoms. We show that the question of whether a PSC program has a preferred stable model is CoNP-complete. We give examples of the uses of the preference set constraint atoms and show that Answer Set Optimization (Brewka, Niemel\\"a, and Truszczynski 2003) and General Preference (Son and Pontelli 2006) can be expressed using preference set constraint atoms.

  7. Effect of crystallographic texture and dislocation hardening on limit strain in sheet metal forming

    Science.gov (United States)

    Wen, Xiyu

    2000-10-01

    In the metal industry, sheet metals are widely used to produce packaging materials for consumer goods, for structures such as automobilse, and for building construction and transportation. The desired shape of the products is imparted by plastic deformation in either the cold or hot state. Traditionally, the prediction of the forming limit of sheet metals is based on tensile tests, simulation tests and continuum mathematical models. Continuum models used in the prediction of the plastic behavior of sheet metals are based on average values of mechanical properties such as elongation, yield strength, work hardening and work-hardening rate, which are usually derived from tensile tests. Although attempts have been made to abandon the phenomenological description of the yield function by applying the theory of crystal plasticity to calculate the yield surface of texture polycrystals and hence the limit strains, only the average properties of the microstructure (e.g., the crystallographic texture of the bulk sheet) have been taken into account. So far, there has been no model for the prediction of the strain path and the limit strain of sheet metals that takes into account the effect of individual grain orientation and the dislocation property. In this thesis, different approaches in the study of plastic deformation are reviewed from the view-point of both macroplasticity and microplasticity. Instead of relying on a unique flow rule to describe the stress and strain relationship, the role of work hardening in the instability process of sheet metal and hence the flow localization phenomenon is explored from a study of the changes in the orientation of the constituent crystallites and from the changes in the dislocation density associated with different grain orientations during the course of large biaxial deformation. The changes in the crystallographic textures of an aluminium sheet sample deformed under various stress states from plane-strain tension to equi

  8. EDITORIAL: Optical orientation Optical orientation

    Science.gov (United States)

    SAME ADDRESS *, Yuri; Landwehr, Gottfried

    2008-11-01

    priority of the discovery in the literature, which was partly caused by the existence of the Iron Curtain. I had already enjoyed contact with Boris in the 1980s when the two volumes of Landau Level Spectroscopy were being prepared [2]. He was one of the pioneers of magneto-optics in semiconductors. In the 1950s the band structure of germanium and silicon was investigated by magneto-optical methods, mainly in the United States. No excitonic effects were observed and the band structure parameters were determined without taking account of excitons. However, working with cuprous oxide, which is a direct semiconductor with a relative large energy gap, Zakharchenya and his co-worker Seysan showed that in order to obtain correct band structure parameters, it is necessary to take excitons into account [3]. About 1970 Boris started work on optical orientation. Early work by Hanle in Germany in the 1920s on the depolarization of luminescence in mercury vapour by a transverse magnetic field was not appreciated for a long time. Only in the late 1940s did Kastler and co-workers in Paris begin a systematic study of optical pumping, which led to the award of a Nobel prize. The ideas of optical pumping were first applied by Georges Lampel to solid state physics in 1968. He demonstrated optical orientation of free carriers in silicon. The detection method was nuclear magnetic resonance; optically oriented free electrons dynamically polarized the 29Si nuclei of the host lattice. The first optical detection of spin orientation was demonstrated by with the III-V semiconductor GaSb by Parsons. Due to the various interaction mechanisms of spins with their environment, the effects occurring in semiconductors are naturally more complex than those in atoms. Optical detection is now the preferred method to detect spin alignment in semiconductors. The orientation of spins in crystals pumped with circularly polarized light is deduced from the degree of circular polarization of the recombination

  9. Maximum a posteriori estimation of crystallographic phases in X-ray diffraction tomography

    Energy Technology Data Exchange (ETDEWEB)

    Gürsoy, Doǧa; Bicer, Tekin; Almer, Jonathan D.; Kettimuthu, Rajkumar; Stock, Stuart; De Carlo, Francesco

    2015-06-13

    A maximum a posteriori approach is proposed for X-ray diffraction tomography for reconstructing three-dimensional spatial distribution of crystallographic phases and orientations of polycrystalline materials. The approach maximizes the a posteriori density which includes a Poisson log-likelihood and an a priori term that reinforces expected solution properties such as smoothness or local continuity. The reconstruction method is validated with experimental data acquired from a section of the spinous process of a porcine vertebra collected at the 1-ID-C beamline of the Advanced Photon Source, at Argonne National Laboratory. The reconstruction results show significant improvement in the reduction of aliasing and streaking artefacts, and improved robustness to noise and undersampling compared to conventional analytical inversion approaches. The approach has the potential to reduce data acquisition times, and significantly improve beamtime efficiency.

  10. Impact of the Crystallite Orientation Distribution on Exciton Transport in Donor–Acceptor Conjugated Polymers

    KAUST Repository

    Ayzner, Alexander L.

    2015-12-30

    © 2015 American Chemical Society. Conjugated polymers are widely used materials in organic photovoltaic devices. Owing to their extended electronic wave functions, they often form semicrystalline thin films. In this work, we aim to understand whether distribution of crystallographic orientations affects exciton diffusion using a low-band-gap polymer backbone motif that is representative of the donor/acceptor copolymer class. Using the fact that the polymer side chain can tune the dominant crystallographic orientation in the thin film, we have measured the quenching of polymer photoluminescence, and thus the extent of exciton dissociation, as a function of crystal orientation with respect to a quenching substrate. We find that the crystallite orientation distribution has little effect on the average exciton diffusion length. We suggest several possibilities for the lack of correlation between crystallographic texture and exciton transport in semicrystalline conjugated polymer films.

  11. Impact of the Crystallite Orientation Distribution on Exciton Transport in Donor-Acceptor Conjugated Polymers.

    Science.gov (United States)

    Ayzner, Alexander L; Mei, Jianguo; Appleton, Anthony; DeLongchamp, Dean; Nardes, Alexandre; Benight, Stephanie; Kopidakis, Nikos; Toney, Michael F; Bao, Zhenan

    2015-12-30

    Conjugated polymers are widely used materials in organic photovoltaic devices. Owing to their extended electronic wave functions, they often form semicrystalline thin films. In this work, we aim to understand whether distribution of crystallographic orientations affects exciton diffusion using a low-band-gap polymer backbone motif that is representative of the donor/acceptor copolymer class. Using the fact that the polymer side chain can tune the dominant crystallographic orientation in the thin film, we have measured the quenching of polymer photoluminescence, and thus the extent of exciton dissociation, as a function of crystal orientation with respect to a quenching substrate. We find that the crystallite orientation distribution has little effect on the average exciton diffusion length. We suggest several possibilities for the lack of correlation between crystallographic texture and exciton transport in semicrystalline conjugated polymer films.

  12. Crystal structure refinement a crystallographers guide to SHELXL

    CERN Document Server

    2006-01-01

    A crystallographers guide to SHELXL, covering various aspects of practical crystal structure refinement, from the treatment of hydrogen atoms to the assignment of atom types, and more. After an introduction to SHELXL, a brief survey of crystal structure refinement is provided.

  13. Optical properties of alpha spodumene: Orientation of its principal optical axes

    Energy Technology Data Exchange (ETDEWEB)

    Souza, S O; Lima, A F [Universidade Federal de Sergipe, Departamento de Fisica, PO Box 353, 49100-000 Sao Cristovao - SE (Brazil); Lalic, M V, E-mail: mlalic@fisica.ufs.b

    2009-05-01

    We studied the orientation of the three orthogonal principal optical axes of the alpha spodumene crystal. This orientation is determined relative to the crystallographic axes, and expressed as function of the incident radiation wavelength in ultraviolent region. The calculations were performed by density functional theory based, full potential augmented plane wave method.

  14. Reconstruction of Single-Grain Orientation Distribution Functions for Crystalline Materials

    DEFF Research Database (Denmark)

    Hansen, Per Christian; Sørensen, Henning Osholm; Sükösd, Zsuzsanna;

    A fundamental imaging problem in microstructural analysis of metals is the reconstruction of local crystallographic orientations from X-ray diffraction measurements. This work deals with the computation of the 3D orientation distribution function for individual grains of the material in considera...

  15. Reconstruction of Single-Grain Orientation Distribution Functions for Crystalline Materials

    DEFF Research Database (Denmark)

    Hansen, Per Christian; Sørensen, Henning Osholm; Sükösd, Zsuzsanna;

    2009-01-01

    A fundamental imaging problem in microstructural analysis of metals is the reconstruction of local crystallographic orientations from X-ray diffraction measurements. This work develops a fast, accurate, and robust method for the computation of the three-dimensional orientation distribution functi...

  16. CRYSTALLOGRAPHIC RELATIONS OF CEMENTITE–AUSTENITE–FERRITE IN THE DIFFUSIVE DECOMPOSITION OF AUSTENITE

    Directory of Open Access Journals (Sweden)

    BOLSHAKOV V. I.

    2016-05-01

    Full Text Available Summary. It was made a search for new and more accurate orientation relations between the crystal lattice in the pearlite and bainite austenite decomposition products. Methods. It were used the methods: transmission electron microscopy, the micro-, mathematical matrix and stereographic analysis. The purpose of the research is with theoretical, numerical and experimental methods to set up to a 0.2 degree angular orientation relations between the lattices of ferrite and cementite in the austenite decomposition products in the temperature range 400 ... 700С. Results. It was established a new, refined value for grids in the diffusion decay of γ → α + (α + θ. Practical significance. It was proposed a new oriented dependence and the corresponding double gnomonic projection with poles to planes α and θ phases, which can be used in patterns of crystallographic lattices relations studies at phase transitions, as well as the subsequent modeling of complex physical processes of structure formation in metals and binary systems.

  17. A new systematic framework for crystallographic analysis of atom probe data

    Energy Technology Data Exchange (ETDEWEB)

    Araullo-Peters, Vicente J., E-mail: vicente.araullopeters@gmail.com [Australian Centre for Microscopy and Microanalysis, University of Sydney (Australia); School of Aerospace, Mechanical and Mechatronic Engineering, University of Sydney (Australia); Breen, Andrew; Ceguerra, Anna V. [Australian Centre for Microscopy and Microanalysis, University of Sydney (Australia); School of Aerospace, Mechanical and Mechatronic Engineering, University of Sydney (Australia); Gault, Baptiste [Department of Materials, University of Oxford, Parks Road, Oxford (United Kingdom); Ringer, Simon P.; Cairney, Julie M. [Australian Centre for Microscopy and Microanalysis, University of Sydney (Australia); School of Aerospace, Mechanical and Mechatronic Engineering, University of Sydney (Australia)

    2015-07-15

    In this article, after a brief introduction to the principles behind atom probe crystallography, we introduce methods for unambiguously determining the presence of crystal planes within atom probe datasets, as well as their characteristics: location; orientation and interplanar spacing. These methods, which we refer to as plane orientation extraction (POE) and local crystallography mapping (LCM) make use of real-space data and allow for systematic analyses. We present here application of POE and LCM to datasets of pure Al, industrial aluminium alloys and doped-silicon. Data was collected both in DC voltage mode and laser-assisted mode (in the latter of which extracting crystallographic information is known to be more difficult due to distortions). The nature of the atomic planes in both datasets was extracted and analysed. - Highlights: • A new analysis method was designed that determines if reconstructed planes are present in atom probe data. • The location, orientation, and planar spacing of these planes are obtained. • This method was applied to simulated, aluminium alloy and silicon data where the extent of planes was shown to vary considerably. • This method can be used to examine atom probe reconstruction quality.

  18. Crystallographic analysis of the solid-state dewetting of polycrystalline gold film using automated indexing in a transmission electron microscope

    Energy Technology Data Exchange (ETDEWEB)

    Jang, S. A.; Lee, H. J.; Oh, Y. J., E-mail: yjoh@hanbat.ac.kr [Department of Advanced Materials Science and Engineering, Hanbat National University, 125, Dongseo-daero, Yuseong-gu, Daejeon 305-719 (Korea, Republic of); Thompson, C. V.; Ross, C. A., E-mail: caross@mit.edu [Department of Materials Science and Engineering, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    2015-12-01

    We analyzed the effect of crystallographic anisotropy on the morphological evolution of a 12-nm-thick gold film during solid-state dewetting at high temperatures using automated indexing tool in a transmission electron microscopy. Dewetting initiated at grain-boundary triple junctions adjacent to large grains resulting from abnormal grain growth driven by (111) texture development. Voids at the junctions developed shapes with faceted edges bounded by low-index crystal planes. The kinetic mobility of the edges varied with the crystal orientation normal to the edges, with a predominance of specific edges with the slowest retraction rates as the annealing time was increased.

  19. Crystallographic Features and State Stability of the Decagonal Quasicrystal in the Al-Co-Cu Alloy System

    Science.gov (United States)

    Nakayama, Kei; Mizutani, Akito; Koyama, Yasumasa

    2016-11-01

    In the Al-Co-Cu alloy system, both the decagonal quasicrystal with the space group of Poverline{10}m2 and its approximant Al13Co4 phase with monoclinic Cm symmetry are present around 20 at. % Co-10 at. % Cu. In this study, we examined the crystallographic features of prepared Al-(30 - x) at. % Co-x at. % Cu samples mainly by transmission electron microscopy in order to make clear the crystallographic relation between the decagonal quasicrystal and the monoclinic Al13Co4 structure. The results revealed a coexistence state consisting of decagonal quasicrystal and approximant Al13Co4 regions in Al-20 at. % Co-10 at. % Cu alloy samples. With the help of the coexistence state, the orientation relationship was established between the monoclinic Al13Co4 structure and the decagonal quasicrystal. In the determined relationship, the crystallographic axis in the quasicrystal was found to be parallel to the normal direction of the (010)m plane in the Al13Co4 structure, where the subscript m denotes the monoclinic system. Based on data obtained experimentally, the state stability of the decagonal quasicrystal was also examined in terms of the Hume-Rothery (HR) mechanism on the basis of the nearly-free-electron approximation. It was found that a model based on the HR mechanism could explain the crystallographic features such as electron diffraction patterns and atomic arrangements found in the decagonal quasicrystal. In other words, the HR mechanism is most likely appropriate for the stability of the decagonal quasicrystal in the Al-Co-Cu alloy system.

  20. Social Value Orientation and Capitalism in Societies

    National Research Council Canada - National Science Library

    Shahrier, Shibly; Kotani, Koji; Kakinaka, Makoto

    2016-01-01

    ... preferences and behaviors. To test this argument, we implemented field experiments of social value orientation and surveys with 1002 respondents for three different areas of Bangladesh: (i) rural, (ii) transitional and (iii...

  1. Chasing sexual orientation: a comparison of commonly used single-indicator measures of sexual orientation.

    Science.gov (United States)

    Korchmaros, Josephine D; Powell, Claudia; Stevens, Sally

    2013-01-01

    This research investigated the utility of single-indicator measures of sexual orientation in examining group differences. Adolescents and young adults reported their sexual orientations, preferences, and partners. Results indicate that, (a) depending on the measure of sexual orientation, 10% to 22% cannot be categorized into a sexual orientation group using a single-indicator measure; (b) self-identified sexual orientation is often incongruent with preference and behavior; (c) incongruity differs by gender and self-identified sexual orientation; and (d) detected differences in gay/lesbian, bisexual, and straight individuals vary by measure of sexual orientation. These results indicate that classification of sexual orientation by single-indicator measures can lead to inconsistent conclusions across studies.

  2. Perfect preferential orientation of nitrogen-vacancy defects in a synthetic diamond sample

    Energy Technology Data Exchange (ETDEWEB)

    Lesik, M.; Roch, J.-F. [Laboratoire Aimé Cotton, CNRS, Université Paris-Sud and Ecole Normale Supérieure de Cachan, 91405 Orsay (France); Tetienne, J.-P.; Jacques, V., E-mail: vjacques@ens-cachan.fr [Laboratoire Aimé Cotton, CNRS, Université Paris-Sud and Ecole Normale Supérieure de Cachan, 91405 Orsay (France); Laboratoire de Photonique Quantique et Moléculaire, Ecole Normale Supérieure de Cachan and CNRS UMR 8537, 94235 Cachan (France); Tallaire, A., E-mail: alexandre.tallaire@lspm.cnrs.fr; Achard, J.; Mille, V.; Gicquel, A. [Laboratoire des Sciences des Procédés et des Matériaux, CNRS and Université Paris 13, 93340 Villetaneuse (France)

    2014-03-17

    We show that the orientation of nitrogen-vacancy (NV) defects in diamond can be efficiently controlled through chemical vapor deposition growth on a (111)-oriented diamond substrate. More precisely, we demonstrate that spontaneously generated NV defects are oriented with a ∼97% probability along the [111] axis, corresponding to the most appealing orientation among the four possible crystallographic axes. Such a nearly perfect preferential orientation is explained by analyzing the diamond growth mechanism on a (111)-oriented substrate and could be extended to other types of defects. This work is a significant step towards the design of optimized diamond samples for quantum information and sensing applications.

  3. Crystallographic data processing for free-electron laser sources

    Energy Technology Data Exchange (ETDEWEB)

    White, Thomas A., E-mail: taw@physics.org; Barty, Anton; Stellato, Francesco [DESY, Notkestrasse 85, 22607 Hamburg (Germany); Holton, James M. [University of California, San Francisco, CA 94158 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Kirian, Richard A. [DESY, Notkestrasse 85, 22607 Hamburg (Germany); Arizona State University, Tempe, AZ 85287 (United States); Zatsepin, Nadia A. [Arizona State University, Tempe, AZ 85287 (United States); Chapman, Henry N. [DESY, Notkestrasse 85, 22607 Hamburg (Germany); University of Hamburg, Luruper Chaussee 149, 22761 Hamburg (Germany)

    2013-07-01

    A processing pipeline for diffraction data acquired using the ‘serial crystallography’ methodology with a free-electron laser source is described with reference to the crystallographic analysis suite CrystFEL and the pre-processing program Cheetah. A processing pipeline for diffraction data acquired using the ‘serial crystallography’ methodology with a free-electron laser source is described with reference to the crystallographic analysis suite CrystFEL and the pre-processing program Cheetah. A detailed analysis of the nature and impact of indexing ambiguities is presented. Simulations of the Monte Carlo integration scheme, which accounts for the partially recorded nature of the diffraction intensities, are presented and show that the integration of partial reflections could be made to converge more quickly if the bandwidth of the X-rays were to be increased by a small amount or if a slight convergence angle were introduced into the incident beam.

  4. Crystallographic changes in lead zirconate titanate due to neutron irradiation

    Directory of Open Access Journals (Sweden)

    Alexandra Henriques

    2014-11-01

    Full Text Available Piezoelectric and ferroelectric materials are useful as the active element in non-destructive monitoring devices for high-radiation areas. Here, crystallographic structural refinement (i.e., the Rietveld method is used to quantify the type and extent of structural changes in PbZr0.5Ti0.5O3 after exposure to a 1 MeV equivalent neutron fluence of 1.7 × 1015 neutrons/cm2. The results show a measurable decrease in the occupancy of Pb and O due to irradiation, with O vacancies in the tetragonal phase being created preferentially on one of the two O sites. The results demonstrate a method by which the effects of radiation on crystallographic structure may be investigated.

  5. A crystallographic perspective on sharing data and knowledge.

    Science.gov (United States)

    Bruno, Ian J; Groom, Colin R

    2014-10-01

    The crystallographic community is in many ways an exemplar of the benefits and practices of sharing data. Since the inception of the technique, virtually every published crystal structure has been made available to others. This has been achieved through the establishment of several specialist data centres, including the Cambridge Crystallographic Data Centre, which produces the Cambridge Structural Database. Containing curated structures of small organic molecules, some containing a metal, the database has been produced for almost 50 years. This has required the development of complex informatics tools and an environment allowing expert human curation. As importantly, a financial model has evolved which has, to date, ensured the sustainability of the resource. However, the opportunities afforded by technological changes and changing attitudes to sharing data make it an opportune moment to review current practices.

  6. Recent developments in crystallographic investigation of martensitic transformation

    Institute of Scientific and Technical Information of China (English)

    GU Nanju; DONG Guixia; LIN Xiaoping; WANG Baoqi; MA Xiaoli

    2004-01-01

    The results and new knowledge obtained in recent years by using an atom force microscope (AFM) to investigate the surface relieves and to reveal the lattice deformation characteristics in martensitic transformation (MT) are summarized. All-round analysis and research about crystallography and morphology of MT have been done based on our "displacement vector" theory. New viewpoints that the "invariant-plane-strain" criterion have no universality and that the large rotation of habit-planes takes place in {557} lath and {225} plate martensites are put forward. Thereby, the formation mode of {557} martensite is established, which is in good agreement with the experimental results. Finally, according to the self-accommodation principle between variants crystallographic calculations of twin and multi-variant martensites in shape memory alloys have been carried out. The calculation method greatly simplifies the crystallographic calculation process of phenomenological theory. And the calculated results are in good agreement with experimental ones.

  7. Crystallographic analysis of the implanted TiNi monocrystal containing misoriented localized shear mesobands in its near-surface layer [001]{sub B2}

    Energy Technology Data Exchange (ETDEWEB)

    Meisner, L. L., E-mail: llm@ispms.tsc.ru; Meisner, S. N., E-mail: msn@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk State University, Tomsk, 634050 (Russian Federation); Tverdokhlebova, A. V., E-mail: a@vtverd.ru; Poletika, T. M., E-mail: poletm@ispms.tsc.ru; Girsova, S. L., E-mail: girs@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation)

    2015-10-27

    The study was carried on for the implanted single TiNi crystal containing misoriented localized shear mesobands in its near-surface layer [001] B2. Due to the response of material to the Si ion implantation treatment of the single TiNi crystal, deformation mesobands would form in its near-surface layer. Specially designed software tools were employed for the treatment of experimental data obtained from X-ray and electron diffraction patterns. The 3D crystallographic orientations were calculated for the localized shear regions, which were displaced relative to one another and with respect to the original monocrystal orientation.

  8. Thermomolecular Orientation of Nonpolar Fluids

    NARCIS (Netherlands)

    Römer, F.; Bresme, F.; Muscatello, J.; Bedeaux, D.; Rubi, J.M.

    2012-01-01

    We investigate the response of molecular fluids to temperature gradients. Using nonequilibrium molecular dynamics computer simulations we show that nonpolar diatomic fluids adopt a preferred orientation as a response to a temperature gradient. We find that the magnitude of this thermomolecular orien

  9. High orientation Al films growth on LiNbO3 single crystal and its adhesion

    Institute of Scientific and Technical Information of China (English)

    LI Dong-mei; CHEN Jing-jing; PAN Feng

    2004-01-01

    High orientation Al films were deposited on 64°Y-XLiNbO3 substrate by DC magnetron sputtering and the influence of deposition temperature on microstructure and adhesion properties of Al films were investigated. The results show that crystallographic orientation of films varies with substrate temperature and the adhesion strength between LiNbO3 and Al films strongly depends on crystallographic orientation of Al films. The (111) orientated Al films shows stronger adhesion strength to LiNbO3 substrate than (100) orientated films. There is an optimum substrate temperature of 60 ℃ and hardening temperature of 200 ℃ for obtaining high (111) orientated Al films with good surface structure and adhesion property. Using this Al film, we have successfully fabricated the SAW filters with high frequency of about 1.89 GHz.

  10. Orienteering injuries

    OpenAIRE

    Folan, Jean M.

    1982-01-01

    At the Irish National Orienteering Championships in 1981 a survey of the injuries occurring over the two days of competition was carried out. Of 285 individual competitors there was a percentage injury rate of 5.26%. The article discusses the injuries and aspects of safety in orienteering.

  11. Transitivity of Preferences

    Science.gov (United States)

    Regenwetter, Michel; Dana, Jason; Davis-Stober, Clintin P.

    2011-01-01

    Transitivity of preferences is a fundamental principle shared by most major contemporary rational, prescriptive, and descriptive models of decision making. To have transitive preferences, a person, group, or society that prefers choice option "x" to "y" and "y" to "z" must prefer "x" to "z". Any claim of empirical violations of transitivity by…

  12. Crystallographically uniform arrays of ordered (In)GaN nanocolumns

    Energy Technology Data Exchange (ETDEWEB)

    Gačević, Ž., E-mail: gacevic@isom.upm.es; Bengoechea-Encabo, A.; Albert, S.; Calleja, E. [ETSIT-ISOM, Universidad Politécnica de Madrid, Avda. Complutense s/n, 28040 Madrid (Spain); Torres-Pardo, A.; González-Calbet, J. M. [Dept. Química Inorgánica, Universidad Complutense, 28040 Madrid (Spain); CEI Campus Moncloa, UCM-UPM, Madrid (Spain)

    2015-01-21

    In this work, through a comparative study of self-assembled (SA) and selective area grown (SAG) (In)GaN nanocolumn (NC) ensembles, we first give a detailed insight into improved crystallographic uniformity (homogeneity of crystallographic tilts and twists) of the latter ones. The study, performed making use of: reflective high energy electron diffraction, X-ray diffraction and scanning electron microscopy, reveals that unlike their SA counterparts, the ensembles of SAG NCs show single epitaxial relationship to both sapphire(0001) and Si(111) underlying substrates. In the second part of the article, making use of X-ray diffraction, we directly show that the selective area growth leads to improved compositional uniformity of InGaN NC ensembles. This further leads to improved spectral purity of their luminescence, as confirmed by comparative macro-photoluminescence measurements performed on SA and SAG InGaN NC ensembles. An improved crystallographic uniformity of NC ensembles facilitates their integration into optoelectronic devices, whereas their improved compositional uniformity allows for their employment in single-color optoelectronic applications.

  13. Crystallographically uniform arrays of ordered (In)GaN nanocolumns

    Science.gov (United States)

    Gačević, Ž.; Bengoechea-Encabo, A.; Albert, S.; Torres-Pardo, A.; González-Calbet, J. M.; Calleja, E.

    2015-01-01

    In this work, through a comparative study of self-assembled (SA) and selective area grown (SAG) (In)GaN nanocolumn (NC) ensembles, we first give a detailed insight into improved crystallographic uniformity (homogeneity of crystallographic tilts and twists) of the latter ones. The study, performed making use of: reflective high energy electron diffraction, X-ray diffraction and scanning electron microscopy, reveals that unlike their SA counterparts, the ensembles of SAG NCs show single epitaxial relationship to both sapphire(0001) and Si(111) underlying substrates. In the second part of the article, making use of X-ray diffraction, we directly show that the selective area growth leads to improved compositional uniformity of InGaN NC ensembles. This further leads to improved spectral purity of their luminescence, as confirmed by comparative macro-photoluminescence measurements performed on SA and SAG InGaN NC ensembles. An improved crystallographic uniformity of NC ensembles facilitates their integration into optoelectronic devices, whereas their improved compositional uniformity allows for their employment in single-color optoelectronic applications.

  14. Scattering of slow ions by various crystallographic planes of tungsten single crystals

    CERN Document Server

    Ermolov, S N; Kortenraad, R; Must, B; Shtinov, E D; Brongersma, K K

    2002-01-01

    The dependence of low-energy ion scattering signal intensity on single crystal surface orientation is investigated, and it is shown that this dependence is not necessarily in direct proportion to atomic density in the uppermost atomic layer. On the basis of comparison of signals from various crystallographic planes of a high purity W single crystal a conclusion is made that the ions scattered from more deep atomic layers contribute considerably to the signal measured for the surface with an open structure. It is shown that reference specimens with a known surface density are needed for quantitative analysis of surface composition by the method of low-energy ion scattering. The best reference specimens are well-oriented single crystals with close-packed planes at the surface, since in this case the low-energy ion scattering signal is proportional to atomic density of the uppermost atomic layer. It single crystals with open surface structure are used as reference specimens the contribution of deeper atomic laye...

  15. Reintroducing electrostatics into macromolecular crystallographic refinement: application to neutron crystallography and DNA hydration.

    Science.gov (United States)

    Fenn, Timothy D; Schnieders, Michael J; Mustyakimov, Marat; Wu, Chuanjie; Langan, Paul; Pande, Vijay S; Brunger, Axel T

    2011-04-13

    Most current crystallographic structure refinements augment the diffraction data with a priori information consisting of bond, angle, dihedral, planarity restraints, and atomic repulsion based on the Pauli exclusion principle. Yet, electrostatics and van der Waals attraction are physical forces that provide additional a priori information. Here, we assess the inclusion of electrostatics for the force field used for all-atom (including hydrogen) joint neutron/X-ray refinement. Two DNA and a protein crystal structure were refined against joint neutron/X-ray diffraction data sets using force fields without electrostatics or with electrostatics. Hydrogen-bond orientation/geometry favors the inclusion of electrostatics. Refinement of Z-DNA with electrostatics leads to a hypothesis for the entropic stabilization of Z-DNA that may partly explain the thermodynamics of converting the B form of DNA to its Z form. Thus, inclusion of electrostatics assists joint neutron/X-ray refinements, especially for placing and orienting hydrogen atoms.

  16. Orientation and the Young Orienteer

    Science.gov (United States)

    Walsh, S. E.; Martland, J. R.

    Orientation within orienteering is dependent on the use of two basic strategies; that is, either a compass or Magnetic-North-based strategy, which relies on the use of one set of information; or the use of a map and landmark-based strategy which relies on the use of at least two sets of information. Walsh and found that, when given the choice, young children use the compass-based strategy when following complex potentially disorientating routes.The efficacy of these two basic orientation strategies was investigated within three different orienteering environments: (1) a familiar known environment; (2) a familiar unknown environment and (3) an unfamiliar unknown environment.Subjects, age range from 9 to 10think aloud particularly the introduction of basic skills to young performers. They support the argument that is essential to introduce the map and compass simultaneously and that relocation and orientation skills should be coached concurrently.

  17. Gravity orientation tuning in macaque anterior thalamus.

    Science.gov (United States)

    Laurens, Jean; Kim, Byounghoon; Dickman, J David; Angelaki, Dora E

    2016-12-01

    Gravity may provide a ubiquitous allocentric reference to the brain's spatial orientation circuits. Here we describe neurons in the macaque anterior thalamus tuned to pitch and roll orientation relative to gravity, independently of visual landmarks. We show that individual cells exhibit two-dimensional tuning curves, with peak firing rates at a preferred vertical orientation. These results identify a thalamic pathway for gravity cues to influence perception, action and spatial cognition.

  18. Age and Value Orientations

    Directory of Open Access Journals (Sweden)

    Asya Kh. Kukubayeva

    2013-01-01

    Full Text Available The present article deals with value orientations and their role in men’s lives, particularly, in young people’s lives. This notion was introduced by the American theoretical sociologist T. Parsons, one of the creators of modern theoretical sociology. The scientist made an attempt to construct the structural and analytical theory of social action, combining personal interests (needs and aims and situation, it takes place in. The issue of value orientations remains acute for psychology. Herein we have considered several most important works, relating to the considered issue. Age aspects of young people’s value orientations are of peculiar interest to us. When analyzing this phenomenon, one should take into consideration the psychological formations, inhere for a certain age. In fact every age has its unique structure, which may change when passing from one development stage to another. Basing on this fact, we’ve considered the values, depending on the age features of the youth, relying upon the works of the scientists, working with different categories of the youth, such as: teenagers, students, children of different nationalities. It is not surprising that most scientists have come to the conclusion that the chief role in value orientation belongs to a family, originates in relations with parents and teachers. The positive reinforcement to the future develops throughout life in accordance with a lifestyle of a family, society and political situation in a state.Life orientations as a type of value orientations show different types of young people’s preferences. Value structure of its consciousness has its own specific character, depending on the age peculiarities. The dynamics of the transition from one age to another is accompanied with the reappraisal of values, eventually, influencing the life strategy of the future generation

  19. Study of the crystallographic architecture of corals at the nanoscale by scanning transmission X-ray microscopy and transmission electron microscopy.

    Science.gov (United States)

    Benzerara, Karim; Menguy, Nicolas; Obst, Martin; Stolarski, Jarosław; Mazur, Maciej; Tylisczak, Tolek; Brown, Gordon E; Meibom, Anders

    2011-07-01

    We have investigated the nanotexture and crystallographic orientation of aragonite in a coral skeleton using synchrotron-based scanning transmission X-ray microscopy (STXM) and transmission electron microscopy (TEM). Polarization-dependent STXM imaging at 40-nm spatial resolution was used to obtain an orientation map of the c-axis of aragonite on a focused ion beam milled ultrathin section of a Porites coral. This imaging showed that one of the basic units of coral skeletons, referred to as the center of calcification (COC), consists of a cluster of 100-nm aragonite globules crystallographically aligned over several micrometers with a fan-like distribution and with the properties of single crystals at the mesoscale. The remainder of the skeleton consists of aragonite single-crystal fibers in crystallographic continuity with the nanoglobules comprising the COC. Our observation provides information on the nm-scale processes that led to biomineral formation in this sample. Importantly, the present study illustrates how the methodology described here, which combines HRTEM and polarization-dependent synchrotron-based STXM imaging, offers an interesting new approach for investigating biomineralizing systems at the nm-scale.

  20. Analyzing Orientations

    Science.gov (United States)

    Ruggles, Clive L. N.

    Archaeoastronomical field survey typically involves the measurement of structural orientations (i.e., orientations along and between built structures) in relation to the visible landscape and particularly the surrounding horizon. This chapter focuses on the process of analyzing the astronomical potential of oriented structures, whether in the field or as a desktop appraisal, with the aim of establishing the archaeoastronomical "facts". It does not address questions of data selection (see instead Chap. 25, "Best Practice for Evaluating the Astronomical Significance of Archaeological Sites", 10.1007/978-1-4614-6141-8_25) or interpretation (see Chap. 24, "Nature and Analysis of Material Evidence Relevant to Archaeoastronomy", 10.1007/978-1-4614-6141-8_22). The main necessity is to determine the azimuth, horizon altitude, and declination in the direction "indicated" by any structural orientation. Normally, there are a range of possibilities, reflecting the various errors and uncertainties in estimating the intended (or, at least, the constructed) orientation, and in more formal approaches an attempt is made to assign a probability distribution extending over a spread of declinations. These probability distributions can then be cumulated in order to visualize and analyze the combined data from several orientations, so as to identify any consistent astronomical associations that can then be correlated with the declinations of particular astronomical objects or phenomena at any era in the past. The whole process raises various procedural and methodological issues and does not proceed in isolation from the consideration of corroborative data, which is essential in order to develop viable cultural interpretations.

  1. Knowledge sharing activities in project-oriented organisations

    DEFF Research Database (Denmark)

    Riis, Eva; Eskerod, Pernille

    2010-01-01

    Findings from examining eleven knowledge sharing activities in five mature project-oriented organisations are presented. Based on in-depth case studies, we claim that mature project-oriented companies will prefer knowledge sharing activities that contribute to an intra-organisational common frame...... of reference. Further, activities that are internal to the companies are preferred to external activities, and non-project-/programme-specific knowledge sharing activities are preferred to project-/programme-specific knowledge sharing activities...

  2. Crystallographic B factor of critical residues at enzyme active site

    Institute of Scientific and Technical Information of China (English)

    张海龙; 宋时英; 林政炯

    1999-01-01

    Thirty-seven sets of crystallographic enzyme data were selected from Protein Data Bank (PDB, 1995). The average temperature factors (B) of the critical residues at the active site and the whole molecule of those enzymes were calculated respectively. The statistical results showed that the critical residues at the active site of most of the enzymes had lower B factors than did the whole molecules, indicating that in the crystalline state the critical residues at the active site of the natural enzymes possess more stable conformation than do the whole molecules. The flexibility of the active site during the unfolding by denaturing was also discussed.

  3. A preference for migration

    OpenAIRE

    Stark, Oded

    2007-01-01

    At least to some extent migration behavior is the outcome of a preference for migration. The pattern of migration as an outcome of a preference for migration depends on two key factors: imitation technology and migration feasibility. We show that these factors jointly determine the outcome of a preference for migration and we provide examples that illustrate how the prevalence and transmission of a migration-forming preference yield distinct migration patterns. In particular, the imitation of...

  4. A preference for migration

    OpenAIRE

    Stark, Oded

    2007-01-01

    At least to some extent migration behavior is the outcome of a preference for migration. The pattern of migration as an outcome of a preference for migration depends on two key factors: imitation technology and migration feasibility. We show that these factors jointly determine the outcome of a preference for migration and we provide examples that illustrate how the prevalence and transmission of a migration-forming preference yield distinct migration patterns. In particular, the imitation of...

  5. The influence of sex on character attribute preferences.

    Science.gov (United States)

    Companion, Michèle; Sambrook, Roger

    2008-12-01

    This study investigates the sex-based differences in preferences for character types and game play. It is hypothesized that males will prefer more combat-oriented roles, while females will prefer less violent ones, with an emphasis on nurturing others and supporting the group. We find support for sex-based differences in character type selection. Violence aversion is a factor for females, while cooperative, nurturing factors are not.

  6. Lifestyles and Preferences for (Public) Goods: Professional Football in Munich

    OpenAIRE

    Gabriel M. Ahlfeldt; Maennig, Wolfgang; Ölschläger, Michaela

    2009-01-01

    This paper investigates the 2001 referendum on the Allianz-Arena, a professional soccer stadium in Munich, Germany, with respect to lifestyle-specific voter preferences. Using political party affiliation and milieu probabilities as proxy variables, we find that lifestyle-specific preferences, values and attitudes more significantly contribute to the explanation of voting outcome compared to traditional strata-orientated indicators of economic wealth. Thus, lifestyle, preferences, tastes and a...

  7. Local orientation measurements in 3D

    DEFF Research Database (Denmark)

    Juul Jensen, D.

    2005-01-01

    The 3 Dimensional X-Ray Diffraction (3DXRD) method is presented and its potentials illustrated by examples. The 3DXRD method is based on diffraction of high energy X-rays and allows fast and nondestructive 3D characterization of the local distribution of crystallographic orientations in the bulk....... The spatial resolution is about 1x5x5 mu m but diffraction from microstructural elements as small as 100 nm may be monitored within suitable samples. As examples of the use of the 3DXRD method, it is chosen to present results for complete 3D characterization of grain structures, in-situ "filming...

  8. Crystallographic alignment of high-density gallium nitride nanowire arrays.

    Science.gov (United States)

    Kuykendall, Tevye; Pauzauskie, Peter J; Zhang, Yanfeng; Goldberger, Joshua; Sirbuly, Donald; Denlinger, Jonathan; Yang, Peidong

    2004-08-01

    Single-crystalline, one-dimensional semiconductor nanostructures are considered to be one of the critical building blocks for nanoscale optoelectronics. Elucidation of the vapour-liquid-solid growth mechanism has already enabled precise control over nanowire position and size, yet to date, no reports have demonstrated the ability to choose from different crystallographic growth directions of a nanowire array. Control over the nanowire growth direction is extremely desirable, in that anisotropic parameters such as thermal and electrical conductivity, index of refraction, piezoelectric polarization, and bandgap may be used to tune the physical properties of nanowires made from a given material. Here we demonstrate the use of metal-organic chemical vapour deposition (MOCVD) and appropriate substrate selection to control the crystallographic growth directions of high-density arrays of gallium nitride nanowires with distinct geometric and physical properties. Epitaxial growth of wurtzite gallium nitride on (100) gamma-LiAlO(2) and (111) MgO single-crystal substrates resulted in the selective growth of nanowires in the orthogonal [1\\[Evec]0] and [001] directions, exhibiting triangular and hexagonal cross-sections and drastically different optical emission. The MOCVD process is entirely compatible with the current GaN thin-film technology, which would lead to easy scale-up and device integration.

  9. Diffusion-equation method for crystallographic figure of merits.

    Science.gov (United States)

    Markvardsen, Anders J; David, William I F

    2010-09-01

    Global optimization methods play a significant role in crystallography, particularly in structure solution from powder diffraction data. This paper presents the mathematical foundations for a diffusion-equation-based optimization method. The diffusion equation is best known for describing how heat propagates in matter. However, it has also attracted considerable attention as the basis for global optimization of a multimodal function [Piela et al. (1989). J. Phys. Chem. 93, 3339-3346]. The method relies heavily on available analytical solutions for the diffusion equation. Here it is shown that such solutions can be obtained for two important crystallographic figure-of-merit (FOM) functions that fully account for space-group symmetry and allow the diffusion-equation solution to vary depending on whether atomic coordinates are fixed or not. The resulting expression is computationally efficient, taking the same order of floating-point operations to evaluate as the starting FOM function measured in terms of the number of atoms in the asymmetric unit. This opens the possibility of implementing diffusion-equation methods for crystallographic global optimization algorithms such as structure determination from powder diffraction data.

  10. Crystallographic studies of gas sorption in metal–organic frameworks

    Science.gov (United States)

    Carrington, Elliot J.; Vitórica-Yrezábal, Iñigo J.; Brammer, Lee

    2014-01-01

    Metal–organic frameworks (MOFs) are a class of porous crystalline materials of modular design. One of the primary applications of these materials is in the adsorption and separation of gases, with potential benefits to the energy, transport and medical sectors. In situ crystallography of MOFs under gas atmospheres has enabled the behaviour of the frameworks under gas loading to be investigated and has established the precise location of adsorbed gas molecules in a significant number of MOFs. This article reviews progress in such crystallographic studies, which has taken place over the past decade, but has its origins in earlier studies of zeolites, clathrates etc. The review considers studies by single-crystal or powder diffraction using either X-rays or neutrons. Features of MOFs that strongly affect gas sorption behaviour are discussed in the context of in situ crystallographic studies, specifically framework flexibility, and the presence of (organic) functional groups and unsaturated (open) metal sites within pores that can form specific interactions with gas molecules. PMID:24892587

  11. Preferences over Social Risk

    DEFF Research Database (Denmark)

    Harrison, Glenn W.; Lau, Morten; Rutström, E. Elisabet;

    2013-01-01

    the methodological issues extend to larger groups that form endogenously (e.g., families, committees, communities). Preferences over social risk can be closely approximated by individual risk attitudes when subjects have no information about the risk preferences of other group members. We find no evidence......We elicit individual preferences over social risk. We identify the extent to which these preferences are correlated with preferences over individual risk and the well-being of others. We examine these preferences in the context of laboratory experiments over small, anonymous groups, although...... that subjects systematically reveal different risk attitudes in a social setting with no prior knowledge about the risk preferences of others compared to when they solely bear the consequences of the decision. However, we also find that subjects are significantly more risk averse when they know the risk...

  12. Orienteering club

    CERN Document Server

    Club d'orientation

    2015-01-01

    Course d'orientation La reprise des courses d’orientation était attendue dans la région puisque près de 150 coureurs ont participé à la première épreuve automnale organisée par le club d’orientation du CERN sur le site de La Faucille. Les circuits ont été remportés par Yann Locatelli du club d’Orientation Coeur de Savoie avec 56 secondes d’avance sur Damien Berguerre du club SOS Sallanches pour le parcours technique long, Marie Vuitton du club CO CERN (membre également de l’Equipe de France Jeune) pour le parcours technique moyen avec presque 4 minutes d’avance sur Jeremy Wichoud du club Lausanne-Jorat, Victor Dannecker pour le circuit technique court devant Alina Niggli, Elliot Dannecker pour le facile moyen et Alice Merat sur le facile court, tous membres du club O’Jura. Les résultats comp...

  13. Crystallographic origin of perpendicular magnetic anisotropy in CoPt film: polarized x-ray absorption study

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, K [National University of Singapore; Chen, J [National University of Singapore; Liu, T [Oak Ridge National Laboratory (ORNL); Sun, C [Singapore Synchrotron Light Source; Chow, G [National University of Singapore

    2009-01-01

    Crystallographic structure, growth induced miscibility gap and strain in Ta/Co100 xPtx (0 x 43 at%)/Ru/Ta/glass films deposited at ambient temperature were investigated using polarized x-ray absorption spectroscopy to clarify the origin of observed perpendicular magnetic anisotropy (PMA) in Co72Pt28 film. Extended x-ray absorption fine structure spectroscopy data at Co K-edge showed that Co has a similar local atomic environment and averaged interatomic distance in the in-plane and out-of-plane polarization geometries for Co72Pt28, ruling out the contribution of magneto-elastic anisotropy and growth induced structural anisotropy as the origin of PMA. A large PMA in Co72Pt28 film was attributed to the preferred hexagonal close-packed stacking as observed using the x-ray absorption near-edge structure spectroscopy.

  14. Quantitative regulation of bone-mimetic, oriented collagen/apatite matrix structure depends on the degree of osteoblast alignment on oriented collagen substrates.

    Science.gov (United States)

    Matsugaki, Aira; Isobe, Yoshihiro; Saku, Taro; Nakano, Takayoshi

    2015-02-01

    Bone tissue has a specific anisotropic morphology derived from collagen fiber alignment and the related apatite crystal orientation as a bone quality index. However, the precise mechanism of cellular regulation of the crystallographic orientation of apatite has not been clarified. In this study, anisotropic construction of cell-produced mineralized matrix in vitro was established by initiating organized cellular alignment and subsequent oriented bone-like matrix (collagen/apatite) production. The oriented collagen substrates with three anisotropic levels were prepared by a hydrodynamic method. Primary osteoblasts were cultured on the fabricated substrates until mineralized matrix formation is confirmed. Osteoblast alignment was successfully regulated by the level of substrate collagen orientation, with preferential alignment along the direction of the collagen fibers. Notably, both fibrous orientation of newly synthesized collagen matrix and c-axis of produced apatite crystals showed preferential orientation along the cell direction. Because the degree of anisotropy of the deposited apatite crystals showed dependency on the directional distribution of osteoblasts cultured on the oriented collagen substrates, the cell orientation determines the crystallographic anisotropy of produced apatite crystals. To the best of our knowledge, this is the first report demonstrating that bone tissue anisotropy, even the alignment of apatite crystals, is controllable by varying the degree of osteoblast alignment via regulating the level of substrate orientation.

  15. Surface energy-mediated construction of anisotropic semiconductor wires with selective crystallographic polarity

    Science.gov (United States)

    Sohn, Jung Inn; Hong, Woong-Ki; Lee, Sunghoon; Lee, Sanghyo; Ku, Jiyeon; Park, Young Jun; Hong, Jinpyo; Hwang, Sungwoo; Park, Kyung Ho; Warner, Jamie H.; Cha, Seungnam; Kim, Jong Min

    2014-07-01

    ZnO is a wide band-gap semiconductor with piezoelectric properties suitable for opto-electronics, sensors, and as an electrode material. Controlling the shape and crystallography of any semiconducting nanomaterial is a key step towards extending their use in applications. Whilst anisotropic ZnO wires have been routinely fabricated, precise control over the specific surface facets and tailoring of polar and non-polar growth directions still requires significant refinement. Manipulating the surface energy of crystal facets is a generic approach for the rational design and growth of one-dimensional (1D) building blocks. Although the surface energy is one basic factor for governing crystal nucleation and growth of anisotropic 1D structures, structural control based on surface energy minimization has not been yet demonstrated. Here, we report an electronic configuration scheme to rationally modulate surface electrostatic energies for crystallographic-selective growth of ZnO wires. The facets and orientations of ZnO wires are transformed between hexagonal and rectangular/diamond cross-sections with polar and non-polar growth directions, exhibiting different optical and piezoelectrical properties. Our novel synthetic route for ZnO wire fabrication provides new opportunities for future opto-electronics, piezoelectronics, and electronics, with new topological properties.

  16. Sexual Orientation (For Parents)

    Science.gov (United States)

    ... Teaching Kids to Be Smart About Social Media Sexual Orientation KidsHealth > For Parents > Sexual Orientation Print A ... orientation is part of that process. What Is Sexual Orientation? The term sexual orientation refers to the ...

  17. Birth Position, Neonatal Head Position Preference, and Hand Preference in 19-Week-Old-Infants.

    Science.gov (United States)

    Goodwin, Rhoda S.

    This study investigated the hypotheses that 1) infants delivered from a left occiput anterior or transverse position (LOA/LOT) would exhibit a right supine head orientation in the neonatal examination and a right hand preference at 19 weeks of age; and 2) infants delivered from a right occiput anterior or transverse position (ROA/ROT) would…

  18. Problem-oriented project studies

    DEFF Research Database (Denmark)

    Nielsen, Jørgen Lerche; Danielsen, Oluf

    2010-01-01

    This contribution focuses on 'problem based learning' (however we prefer the notion of ‘problem-oriented project studies’) and the role of the teacher in such a context. The classic traditional role as an expert deciding the curriculum, providing lectures and seminars, giving assignments and mark......This contribution focuses on 'problem based learning' (however we prefer the notion of ‘problem-oriented project studies’) and the role of the teacher in such a context. The classic traditional role as an expert deciding the curriculum, providing lectures and seminars, giving assignments...... and marking papers / essays is complemented and in some way overruled by a new role as supervisor and facilitator for the group of students working with a research problem, they themselves have picked. However different dimensions of this new teacher role can be seen – from expert in an academic field (result...

  19. The Shared Signal Hypothesis: Effects of Emotion-Gaze Congruency in Infant and Adult Visual Preferences

    Science.gov (United States)

    Rigato, Silvia; Menon, Enrica; Farroni, Teresa; Johnson, Mark H.

    2013-01-01

    In this study, 4-month-old infants' and adults' spontaneous preferences for emotional and neutral displays with direct and averted gaze are investigated using visual preference paradigms. Specifically, by presenting two approach-oriented emotions (happiness and anger) and two avoidance-oriented emotions (fear and sadness), we asked whether the…

  20. Crystallographic texture and microstructural changes in fusion welds of recrystallized Zry-4 rolled plates

    Science.gov (United States)

    Moya Riffo, A.; Vicente Alvarez, M. A.; Santisteban, J. R.; Vizcaino, P.; Limandri, S.; Daymond, M. R.; Kerr, D.; Okasinski, J.; Almer, J.; Vogel, S. C.

    2017-05-01

    This work presents a detailed characterization of the microstructural and crystallographic texture changes observed in the transition region in a weld between two Zircaloy-4 cold rolled and recrystallized plates. The microstructural study was performed by optical microscopy under polarized light and scanning electron microscopy (SEM). Texture changes were characterized at different lengthscales: in the micrometric size, orientation imaging maps (OIM) were constructed by electron backscatter diffraction (EBSD), in the millimetre scale, high energy XRD experiments were done at the Advanced Photon Source (USA) and compared to neutron diffraction texture determinations performed in the HIPPO instrument at Los Alamos National Laboratory. In the heat affected zone (HAZ) we observed the development of Widmanstätten microstructures, typical of the α(hcp) to β(bcc) phase transformation. Associated with these changes a rotation of the c-poles is found in the HAZ and fusion zone. While the base material shows the typical texture of a cold rolled plate, with their c-poles pointing 35° apart from the normal direction of the plate in the normal-transversal line, in the HAZ, c-poles align along the transversal direction of the plate and then re-orient along different directions, all of these changes occurring within a lengthscale in the order of mm. The evolution of texture in this narrow region was captured by both OIM and XRD, and is consistent with previous measurements done by Neutron Diffraction in the HIPPO diffractometer at Los Alamos National Laboratory, USA. The microstructural and texture changes along the HAZ were interpreted as arising due to the effect of differences in the cooling rate and β grain size on the progress of the different α variants during transformation. Fast cooling rates and large β grains are associated to weak variant selection during the β->α transformation, while slow cooling rates and fine β grains result in strong variant selection.

  1. Crystallographic texture and microstructural changes in fusion welds of recrystallized Zry-4 rolled plates

    Energy Technology Data Exchange (ETDEWEB)

    Riffo, A. Moya; Alvarez, M.A.Vicente; Santisteban, J R; Vizcaino, P; Limandri, S.; Daymond, M. R.; Kerr, D.; Vogel, S C; Almer, J.; Okasinski, J.

    2017-02-08

    This study presents a detailed characterization of the microstructural and crystallographic texture changes observed in the transition region in a weld between two Zircaloy-4 cold rolled and recrystallized plates. The microstructural study was performed by optical microscopy under polarized light and scanning electron microscopy (SEM). Texture changes were characterized at different lengthscales: in the micrometric size, orientation imaging maps (OIM) were constructed by electron backscatter diffraction (EBSD), in the millimetre scale, high energy XRD experiments were done at the Advanced Photon Source (USA) and compared to neutron diffraction texture determinations performed in the HIPPO instrument at Los Alamos National Laboratory. In the heat affected zone (HAZ) we observed the development of Widmanstätten microstructures, typical of the α(hcp) to β(bcc) phase transformation. Associated with these changes a rotation of the c-poles is found in the HAZ and fusion zone. While the base material shows the typical texture of a cold rolled plate, with their c-poles pointing 35° apart from the normal direction of the plate in the normal-transversal line, in the HAZ, c-poles align along the transversal direction of the plate and then re-orient along different directions, all of these changes occurring within a lengthscale in the order of mm. The evolution of texture in this narrow region was captured by both OIM and XRD, and is consistent with previous measurements done by Neutron Diffraction in the HIPPO diffractometer at Los Alamos National Laboratory, USA. The microstructural and texture changes along the HAZ were interpreted as arising due to the effect of differences in the cooling rate and β grain size on the progress of the different α variants during transformation. Fast cooling rates and large β grains are associated to weak variant selection during the β–>α transformation, while slow cooling rates and fine β grains result in strong

  2. Influence of the type of electrolyte on the morphological and crystallographic characteristics of lead powder particles

    Directory of Open Access Journals (Sweden)

    Nikolić Nebojša D.

    2013-01-01

    Full Text Available Lead electrodeposition processes from the basic (nitrate and complex (acetate electrolytes were mutually compared by the scanning electron microscopic and the X-ray diffraction analysis of the produced powder particles. The shape of dendritic particles strongly depended on the type of electrolyte. The dendrites composed of stalk and weakly developed primary branches (the primary type were predominantly formed from the basic electrolyte. The ramified dendrites composed of stalk and of both primary and secondary branches (the secondary type were mainly formed from the complex electrolyte. In the both type of powder particles Pb crystallites were predominantly oriented in the (111 plane. Formation of powder particles of the different shape with the strong (111 preferred orientation was discussed and explained by the consideration of the general characteristics of the growth of a crystal in the electrocrystallization processes. [Projekat Ministarstva nauke Republike Srbije, br. 172046: Electrochemical synthesis and characterization of nanostructured functional materials for application in new technologies

  3. Angular distribution of the emission from ultrarelativistic electrons moving near crystallographic axes in diamond and tungsten crystals

    Energy Technology Data Exchange (ETDEWEB)

    Aleinik, A.N.; Vorobev, S.A.; Kalinin, B.N.; Kurkov, A.A.; Potylitsyn, A.P.

    1986-07-01

    Data on the angular distribution of the emission from ultrarelativistic electrons moving near crystallographic axes in diamond and tungsten crystals are reviewed. A graph is presented of the orientational dependence of soft gamma rays measured by a thin-walled ionization chamber sensitive to gamma rays with energies greater than 0.3 MeV and a radiative loss measured by a total-absorption Gauss quantometer with a threshold of about 5 MeV at an angle to the primary electron-beam direction of motion. It is concluded that knowledge of the scattering processes of ultrarelativistic electrons near crytal axes makes it easier to choose the optimum type and thickness of a crystal to achieve the maximum yield of gamma radiation into a given solid angle. 8 references.

  4. Crystallographic investigation of aluminium nitride thin films on stainless steel foil for highly efficient piezoelectric vibration energy harvesters

    Science.gov (United States)

    Moriwaki, N.; Minh, L. V.; Ohigashi, R.; Shimada, O.; Kitayoshi, H.; Kuwano, H.

    2016-11-01

    This study reports piezoelectric properties and crystallographic microstructures of aluminium nitride (AlN, wurtzite structure) thin films on 50 μm thick stainless steel foil. The transverse piezoelectric coefficient d31f and e31f of 10 pm thick AlN films were estimated as -1.42 ± 0.08 μm/V and -0.48 ± 0.03 C/m2 from a tip displacement of the piezoelectric cantilevers. Dielectric constant s33 was measured as 10.5 ± 1.0. An electron beam diffraction pattern by a high-resolution transmission electron microscope and x-ray diffraction pattern showed that abundance ratio of the orientation such as , and of AlN crystal on stainless steel foils increased with increasing thickness.

  5. Orienteering Club

    CERN Document Server

    Club d'orientation

    2013-01-01

    Courses d’orientation Une bonne dizaine de clubs étaient représentés samedi dernier à La Faucille pour participer à la  2e manche de la coupe genevoise organisée par le club du CERN. Les 120 coureurs ont pu découvrir des parcours classés "technique". Ceux du Haut-Jura familiarisés à ce type de terrain ont pu sortir leur épingle du jeu et se sont octroyé la victoire sur 4 des 5 circuits. Samedi 21 septembre, la montagne du Haut-Jura était encore plébiscitée puisque les coureurs étaient attendus à Saint Cergue sur la carte des Pralies. Pour les résultats complets de La Faucille et les informations sur la prochaine étape, consultez le site du club http://cern.ch/club-orientation.

  6. Crystallographic shear mechanisms in Rh one-dimensional oxides

    Science.gov (United States)

    Hernando, María; Boulahya, Khalid; Parras, Marina; González-Calbet, José M.

    2005-02-01

    Electron diffraction and high resolution electron microscopy have been used to characterize two new one-dimensional superstructures in the A sbnd Rh sbnd O system (A = Ca, Sr) related to the 2H-ABO 3-type. They are formed by the intergrowth of n A 3A'BO 6 blocks, showing the Sr 4RhO 6-type, with A 12A' 2B 8O 30 blocks, constituted by two A 3O 9 and two A 3A'O 6 layers alternating in the stacking sequence 1:1, leading to the A 27A' 7B 13O 60 ( n=5) and A 30A' 8B 14O 66 ( n=6) compositions. A crystallographic shear mechanism is proposed to describe the structural relationship between Sr 4RhO 6 (A 3A'BO 6-type) and the new superstructures.

  7. Orientation Relationships between Ferrite and Cementite by Edge-to-edge Matching Principle

    Institute of Scientific and Technical Information of China (English)

    Ning Zhong; Xiaodong Wang; Zhenghong Guo; Yonghua Rong

    2011-01-01

    The crystallographic features of pearlite were investigated by experiments and edge-to-edge matching principle. Two new orientation relationships between ferrite and cementite were determinated by selected area electron diffraction and then explained by our modified edge-to-edge matching method. The consistence of the experimental results with theoretical prediction confirms the practicability of the modified edge-to-edge matching model.

  8. Evolution of orientations and deformation structures within individual grains in cold rolled columnar grained nickel

    DEFF Research Database (Denmark)

    Wu, G.L.; Godfrey, A.; Winther, Grethe;

    2011-01-01

    Columnar grained Ni is used as a model material allowing simultaneous non-surface investigations of the evolution of crystallographic orientations and deformation microstructures within individual grains as a function of rolling strain up to ε=0.7. Electron channelling contrast and electron...

  9. Orientation Club

    CERN Multimedia

    Club d'orientation

    2014-01-01

    COURSE ORIENTATION Résultats de samedi 10 mai    C’est sur une carte entièrement réactualisée dans les bois de Versoix, que plus de 100 coureurs sont venus participer à la course d’orientation, type longue distance, préparée par des membres du club du CERN. Le terrain plutôt plat nécessitait une orientation à grande vitesse, ce qui a donné les podiums suivants :  Technique long avec 17 postes : 1er Jurg Niggli, O’Jura en 52:48, 2e Beat Muller, COLJ Lausanne-Jorat en 58:02, 3e Christophe Vuitton, CO CERN en 58:19 Technique moyen avec 13 postes : 1er Jean-Bernard Zosso, CO CERN, en 46:05 ; 2e Yves Rousselot, Balise 25 Besançon, en 55:11 ; 3e Laurent Merat, O'Jura, en 55:13 Technique court avec 13 postes : 1er Julien Vuitton, CO CERN en 40:59, 2e Marc Baumgartner, CO CERN en 43:18, 3e Yaelle Mathieu en 51:42 Su...

  10. Orienteering Club

    CERN Multimedia

    Club d'orientation

    2013-01-01

    Courses d’orientation ce printemps Le Club d’orientation du CERN vous invite à venir découvrir la course d’orientation et vous propose, en partenariat avec d’autres clubs de la région, une dizaine de courses populaires. Celles-ci ont lieu les samedis après-midi, elles sont ouvertes à tous, quel que soit le niveau, du débutant au sportif confirmé, en famille ou en individuel, en promenade ou en course. Si vous êtes débutant vous pouvez profiter d’une petite initiation offerte par l’organisateur avant de vous lancer sur un parcours. Divers types de parcours sont à votre choix lors de chaque épreuve : facile court (2-3 km), facile moyen (3-5 km), technique court (3-4 km), technique moyen (4-5 km) et technique long (5-7 km). Les dates à retenir sont les suivantes : Samedi 23 mars: Pully (Vd) Samedi 13 avril: Pougny...

  11. Investigation on the Orientation Transition of Oriented Magnetostrictive TbDyFe Crystals

    Institute of Scientific and Technical Information of China (English)

    LIU Wei; JIANG Cheng-bao

    2006-01-01

    and TbDyFe magnetostrictive oriented crystals were prepared by the zone-melting unidirectional solidification method at 240 mm/h and 720 mm/h respectively. oriented crystals were also obtained with oriented seeds with the same technique as for growing the oriented crystals. It is confirmed that this technique is stable for growing the oriented crystals in the TbDyFe alloys. Meanwhile, the variation of orientation, the solidification morphology and the magnetostriction were studied during the transition from oriented seeds to the oriented crystal growth. As the growth speeds up, the preferred orientation changed from to , and its morphology develops from of initial cellular to dendritic gradually. When an axial compressive pre-stress of 10 MPa is applied, the magnetostriction at the bottom, the middle and the top are 972×10-6, 918×10-6 and 900×10-6 at 100 mT respectively. The middle sections with mixed orientations have the same high magnetostriction performance as those with a single preferred orientation, which may be due to its celluar-dendritic morphology.

  12. Transuranic Hybrid Materials: Crystallographic and Computational Metrics of Supramolecular Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Surbella, Robert G. [Department; Ducati, Lucas C. [Department; Pellegrini, Kristi L. [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; McNamara, Bruce K. [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Autschbach, Jochen [Department; Schwantes, Jon M. [Pacific Northwest National Laboratory, 902 Battelle Boulevard, Richland, Washington 99354, United States; Cahill, Christopher L. [Department

    2017-07-26

    A family of twelve supramolecular [AnO2Cl4]2- (An = U, Np, Pu) containing compounds assembled via hydrogen and halogen bonds donated by substituted 4-X-pyridinium cations (X = H, Cl, Br, I) is reported. These materials were prepared from a room-temperature synthesis wherein crystallization of unhydrolyzed and valence pure [An(VI)O2Cl4]2- (An = U, Np, Pu) tectons are the norm. We present a hierarchy of assembly criteria based on crystallographic observations, and subsequently quantify the strengths of the non-covalent interactions using Kohn-Sham density functional calculations. We provide, for the first time, a detailed description of the electrostatic potentials (ESPs) of the actinyl tetrahalide dianions and reconcile crystallographically observed structural motifs and non-covalent interaction (NCI) acceptor-donor pairings. Our findings indicate that the average electrostatic potential across the halogen ligands (the acceptors) changes by only ~2 kJ mol-1 across the AnO22+ series, indicating the magnitude of the potential is independent of the metal center. The role of the cation is therefore critical in directing structural motifs and dictating the resulting hydrogen and halogen bond strengths, the former being stronger due to the positive charge centralized on the pyridyl nitrogen N-H+. Subsequent analyses using the Quantum theory of atoms in molecules (QTAIM) and natural bond orbital (NBO) approaches support this conclusion and highlight the structure directing role of the cations. Whereas one can infer that the 2 Columbic attraction is the driver for assembly, the contribution of the non-covalent interaction is to direct the molecular-level arrangement (or disposition) of the tectons.

  13. Preference, priorities and belief

    NARCIS (Netherlands)

    de Jongh, D.; Liu, F.; Grüne-Yanoff, T.; Hansson, S.O.

    2009-01-01

    In this paper we consider preference over objects. We show how this preference can be derived from priorities, properties of these objects, a concept which is initially from optimality theory. We do this both in the case when an agent has complete information and in the case when an agent only has b

  14. von Neumann Morgenstern Preferences

    DEFF Research Database (Denmark)

    Vind, Karl

    von Neumann Morgenstern utility is generalized to von Neumann Morgenstern preferences. The proof is an application of simple hyperplane theorems......von Neumann Morgenstern utility is generalized to von Neumann Morgenstern preferences. The proof is an application of simple hyperplane theorems...

  15. von Neumann Morgenstern Preferences

    DEFF Research Database (Denmark)

    Vind, Karl

    2000-01-01

    von Neumann Morgenstern utility is generalized to von Neumann Morgenstern preferences. The proof is an application of simple hyperplane theorems......von Neumann Morgenstern utility is generalized to von Neumann Morgenstern preferences. The proof is an application of simple hyperplane theorems...

  16. Eye tracking social preferences

    NARCIS (Netherlands)

    Jiang, Ting; Potters, Jan; Funaki, Yukihiko

    We hypothesize that if people are motivated by a particular social preference, then choosing in accordance with this preference will lead to an identifiable pattern of eye movements. We track eye movements while subjects make choices in simple three-person distribution experiments. We characterize

  17. Consumers’ preferences for bread

    DEFF Research Database (Denmark)

    Edenbrandt, Anna Kristina; Gamborg, Christian; Thorsen, Bo Jellesmark

    2017-01-01

    Consumers are apprehensive about transgenic technologies, so cisgenics, which limit gene transfers to sexually compatible organisms, have been suggested to address consumer concerns. We study consumer preferences for rye bread alternatives based on transgenic or cisgenic rye, grown conventionally...... pesticide-free production methods, and that while cisgenics is preferred over transgenics, the majority of respondents favour traditional breeding methods. The distribution in preferences suggests that some respondents prefer bread from cisgenic crops produced without pesticides over traditional crops...... produced using pesticides. Preferences for organic bread are stronger than for pesticide-free products. From a policy perspective results suggest that excluding cisgenics from mandatory labeling in the EU, or including it in the voluntary non-GM labelling in the US, would cause welfare losses for consumers....

  18. The relationship between personality types and reward preferences

    Directory of Open Access Journals (Sweden)

    R. Nienaber

    2011-12-01

    Full Text Available Orientation: Research has shown that total rewards models structured according to individual preferences, positively influence efforts to attract, retain and motivate key employees. Yet, this is seldom done. Structuring total rewards models according to the preferences of employee segments is a viable alternative to accommodate individual preferences. Research purpose: The primary aim of the study was to determine the relationship between personality types and reward preferences. The secondary aim was to determine the reward preferences for different demographic groups. Motivation for the study: An enhanced understanding of reward preferences for different employee segments will enable employers to offer more competitive reward options to their employees. This may, in turn, have a positive impact on retention. Research design, approach and method: Two measuring instruments, the MBTI® Form GRV and the Rewards Preferences Questionnaire, were distributed electronically to 5 000 potential respondents. The results from 589 sets of questionnaires were used in the data analyses. Primary and secondary factor analyses were done on the items in the Rewards Preferences Questionnaire. Main findings/results: The study confirmed that individuals with certain personality types and personality preferences, have different preferences for certain reward categories. There was a stronger relationship between reward preferences and personality preferences than for reward preferences and personality types. Preferences for reward categories by different demographic groups were confirmed. The significant difference in reward preferences between Black and White respondents in particular was noteworthy, with Black respondents indicating significantly higher mean scores for all reward categories than White respondents. Finally, a total rewards framework influenced by the most prominent preferences for reward categories, was designed. Practical/Managerial implications

  19. Club Orientation

    CERN Multimedia

    Club d'orientation

    2014-01-01

      COURSE ORIENTATION   Pas moins de 100 concurrents sont venus s’affronter sur les parcours proposés par le club d’orientation du CERN ce samedi 26 avril lors de la 4e étape de la coupe genevoise de printemps. Les podiums ont été attribués à :  Technique long avec 19 postes : 1er Yvan Balliot, ASO Annecy en 1:01:39 ; 2e Dominique Fleurent, ASO Annecy, en 1:05:12 ; 3e Rémi Fournier, SOS Sallanches, en 1:05:40. Technique moyen avec 14 postes : 1er Jean-Bernard Zosso, CO CERN, en 46:42 ; 2e Céline Zosso, CO CERN, en 50:51 ; 3e Clément Poncet, O’Jura Prémanon, en 51:27. Technique court avec 13 postes : 1er Jaakko Murtomaki, YKV Seinaejoki, en 36:04 ; 2e Marc Baumgartner en 41:27 ; 3e Natalia Niggli, O’Jura Prémanon, en 52:43. Sur les parcours facile moyen et facile court, victoire respectivement de Stéphanie...

  20. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2012-01-01

     Course d’orientation C’est sous un magnifique soleil que s’est tenue la 7e épreuve de la coupe genevoise organisée par le club d’orientation du CERN. Les organisateurs avaient concocté des parcours assez techniques sur le site de La Faucille. Sur le parcours technique long, beau podium avec la victoire de Domenico Lepori (double médaillés aux championnats du monde en 2010 en vétéran) du club Care Vevey en 1:00:23, juste devant Jürg Niggli du club O’Jura en 1:00:56 puis Beat Mueller du club Lausanne-Jorat en 1:04:28. Sur le parcours technique moyen, Franck Longchampt s’est octroyé la première place, sur le parcours technique court, le jeune Julien Vuitton, qui n’a pas tout à fait 11 ans, a remporté son circuit. Coté parcours facile moyen, Victor Kuznetsov a une fois de plus gagn&eacut...

  1. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2013-01-01

    Course d’orientation Face aux Championnats de France des Clubs à Poitiers, et à une météo hivernale (vent glaciale et pluie), il ne restait qu’une cinquantaine d’orienteurs pour participer à l’épreuve organisée le samedi 25 mai à Grange-Malval. Les participants ont tout de même bien apprécié les 5 circuits proposés par le Satus Genève. Les résultats sont disponibles sur notre site http://cern.ch/club-orientation. En plus des résultats, vous pourrez noter des informations sur la nouvelle école de CO encadrée par B. Barge, Prof. EPS à Ferney-Voltaire pour les jeunes à partir de 6 ans. La prochaine étape de la coupe genevoise se déroulera samedi 1er juin à Morez (39). Epreuve organisée par le club O’Jura&nb...

  2. Orienteering club

    CERN Multimedia

    Club d'orientation

    2010-01-01

    Course d’orientation : Coupe Genevoise de printemps 2010 Et c’est reparti pour une nouvelle saison! Pour cette coupe de printemps 2010, le Club d’Orientation du CERN, en partenariat avec d’autres clubs de la région, vous propose le calendrier suivant: – samedi 20 mars : Cossonay (Vd) – samedi 10 avril : Echallens (Vd) – samedi 17 avril : Trélex (Vd) – samedi 24 avril : Genolier (Vd) – samedi 1 mai : Vulbens/Valleiry (74) – samedi 8 mai : Bois de la Rippe (Vd) – samedi 29 mai : Sauvabellin (Vd) : relais – samedi 5 juin: St Cergue (Vd) : grande finale Les courses populaires ont lieu en général le samedi après-midi, elles sont ouvertes à tous, quel que soit le niveau, du débutant au sportif confirmé, en famille ou en individuel, en promenade ou en course. Pour cela, divers types de parcours sont &agr...

  3. Orienteering club

    CERN Multimedia

    Club d’Orientation du CERN

    2015-01-01

    Courses d’orientation Nouvelle saison nouveau programme Le Club d’orientation du CERN, en partenariat avec d’autres clubs de la région, vous propose une dizaine de courses populaires comptant pour la coupe Genevoise de printemps: samedi 28 mars: Vernand Dessus samedi 18 avril: Pougny/Challex samedi 25 avril: Chancy/Valleiry samedi 2 mai: Mauvernay samedi 9 mai: Longchaumois samedi 16 mai: Genolier samedi 30 mai: Prevondavaux samedi 6 juin: Biere-Ballens samedi 13 juin: Haut-Jura samedi 20 juin: Bonmont - Finale Ces courses sont ouvertes à tous, quel que soit le niveau, du débutant au sportif confirmé, en famille ou en individuel, en promenade ou en course. Les inscriptions se font sur place le jour de l’épreuve. Si vous êtes débutant, vous pouvez profiter d’une initiation offerte par l’organisateur avant de vous lancer sur un parcours. Le club propose aussi...

  4. Orienteering club

    CERN Multimedia

    Orienteering Club

    2016-01-01

    Course d'orientation Calendrier des courses d’orientation Coupe genevoise d’automne 2016 Samedi 3 septembre : La Faucille (01) Samedi 10 septembre : Prémanon (39) Samedi 17 septembre : Saint-Cergue (VD) Samedi 24 septembre : Jorat / Corcelles (VD) Samedi 1 octobre: Bière - Ballens (VD) -relais Vendredi 14 octobre : Parc Mon Repos (GE) - nocturne Samedi 15 octobre : Terrasse de Genève (74) Samedi 29 octobre : Bonmont (VD) Samedi 5 novembre : Pomier (74) – one-man-relay - Finale   Courses ouvertes à toutes et à tous, sportifs, familles, débutants ou confirmés, du CERN ou d’ailleurs. Cinq circuits disponibles, ceci va du facile court (2 km) adapté aux débutants et aux enfants jusqu’au parcours technique long de 6 km pour les chevronnés en passant par les parcours facile moyen (4&am...

  5. COURSE ORIENTATION

    CERN Multimedia

    Club d'orientation du CERN

    2015-01-01

      Les coureurs d’orientation de la région se sont donné rendez-vous samedi dernier dans les bois de Pougny/Challex lors de l’épreuve organisée par le club d’orientation du CERN. La carte proposée pour les 5 circuits offrait aussi bien un coté très technique avec un relief pentu qu’un coté avec de grandes zones plates à forêt claire. Le parcours technique long comportant 20 postes a été remporté par Beat Muller du COLJ Lausanne en 56:26 devançant Denis Komarov, CO CERN en 57:30 et Yvan Balliot, ASO Annecy en 57:46. Pour les autres circuits les résultats sont les suivants: Technique moyen (13 postes): 1er Joël Mathieu en 52:32 à une seconde du 2e Vladimir Kuznetsov, COLJ Lausanne-Jorat, 3e Jean-Bernard Zosso, CO CERN, en 54:01 Technique court (12 postes): 1er Lennart Jirden, ...

  6. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2017-01-01

    Calendrier des courses de la Coupe Genevoise – printemps 2017 Club d'orientation - Julien,  jeune membre du club. Le Club d’orientation du CERN, en partenariat avec d’autres clubs de la région, vous propose une série de courses populaires, qui se dérouleront des deux côtés de la frontière franco-suisse, à savoir : Samedi 1 avril : Pougny/Challex (01) Samedi 8 avril: Ballens (VD) Samedi 22 avril: Apples (VD) Samedi 29 avril: Mont Mussy (01) Samedi 6 mai: Prémanon (39) Samedi 13 mai: Mont Mourex (01) Samedi 20 mai: Prévondavaux (VD) Samedi 10 juin: Chancy/Valleiry (74) Samedi 17 juin: Trélex - Finale (VD) Ces courses sont ouvertes à tous, quel que soit le niveau, du débutant au sportif confirmé, en famille ou en individuel. Les inscriptions sur un des 5 parcours proposés se font sur place le jour de...

  7. Orienteering Club

    CERN Multimedia

    Club d'orientation

    2010-01-01

    COURSE D’ORIENTATION La finale de la coupe de printemps Après avoir remporté le challenge club, samedi 29 juin lors du relais inter-club à Lausanne, le Club d’orientation du CERN organisait la dernière étape de la coupe genevoise de printemps samedi 5 juin à Saint-Cergue dans les bois de Monteret (Canton de Vaud). Plus de 100 participants se sont déplacés pour venir participer à la finale et découvrir une toute nouvelle carte dans une forêt vallonnée. Les résultats pour chaque circuit de cette étape sont : Technique long : 1. Jurg Niggli du club O’Jura, 2. Clément Poncet, 3. Oystein Midttun. Technique moyen : 1. Zoltan Trocsanyi CO CERN, 2. Christophe Ingold, 3. Christina Falga. Technique court : 1. Pierre-Andre Baum, CARE Vevey, 2. Emese Szunyog, 3. Solène Balay. Facile moyen : 1. Elisa P...

  8. Orienteering Club

    CERN Multimedia

    Le Club d’orientation du CERN

    2017-01-01

    Course orientation Les courses d’orientation comptant pour la coupe genevoise de printemps s’enchainent dans la région franco-suisse. Samedi dernier, une bonne centaine de coureurs se sont retrouvés au Mont Mourex où le club du CERN avait préparé la sixième épreuve. A l’issue de la course, les participants confirmaient l’exigence des circuits, à savoir la condition physique et le côté technique du traçage. Le parcours technique long comportant 20 postes a été remporté par Darrell High du Care Vevey en 1:22:38 devançant Beat Muller du COLJ Lausanne-Jorat en 1:25:25 et Alison High également du Care Vevey en 1:28:51. Le circuit technique moyen a été remporté par Christophe Vuitton du CO CERN et le circuit technique court par Claire-Lise Rouiller, CO CERN. Les trois pr...

  9. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2015-01-01

    Course orientation C’est au pied du Salève, proche du Golf de Bosset, que le club d’orientation du CERN (CO CERN) a organisé samedi 19 septembre une nouvelle épreuve comptant pour la Coupe Genevoise d’automne. La zone « des Terrasses de Genève » avait été cartographiée et mise en service l’année dernière. Les participants ont pu apprécier un terrain ludique avec beaucoup de microreliefs, de points d’eau et de gros rochers, le tout au milieu d’une forêt assez claire et agréable à courir. Sur le parcours technique long, le résultat a été très serré puisque Pierrick Merino du club d’Annecy a gagné avec seulement 9 secondes d’avance sur Gaëtan Vuitton (CO CERN) qui confiait avoir perdu beaucoup du te...

  10. Moral Orientation Dynamics in Adolescence and Youth

    Directory of Open Access Journals (Sweden)

    Molchanov S.V.

    2015-02-01

    Full Text Available The problem of moral development is actual for modern psychology. Modern conception of moral development defines two main principles in the basis of moral orientation: care principle and justice principle. Adolescence and youth are sensitive period to develop moral orientation. 139 subjects from three age groups: young adolescents, older adolescents and youth took part in the investigation. Results shows age dynamic of moral judgments preferences, moral dilemma solving with different levels of motivation to achieve and be approved.

  11. Stability, reliability and validity of social value orientation

    NARCIS (Netherlands)

    Bekkers, René

    2004-01-01

    Social value orientations are often regarded as stable individual differences in otherregarding preferences - the concern for equality and joint outcomes - affecting the propensity to cooperate in experimental social dilemma situations. Despite the widespread use of measures of social value orientat

  12. Stability, reliability and validity of social value orientation

    NARCIS (Netherlands)

    Bekkers, René

    2004-01-01

    Social value orientations are often regarded as stable individual differences in otherregarding preferences - the concern for equality and joint outcomes - affecting the propensity to cooperate in experimental social dilemma situations. Despite the widespread use of measures of social value orientat

  13. Orienteering club

    CERN Document Server

    Club d'orientation

    2011-01-01

    Reprise fin août Le Club d’orientation, en partenariat avec d’autres clubs de la région, vous propose une nouvelle série de courses pour cet automne. Le calendrier à retenir est le suivant : Samedi 27 août : Granges Malval (GE) – type classique Samedi 10 septembre : Lamoura (39) – type classique Samedi 17 septembre : La Dôle (F/VD) – type classique Samedi 24 septembre : Monteret (VD) – relais Samedi 8 octobre : Saint Cergue (VD) – type classique Vendredi 14 octobre : Les Evaux (GE) – nocturne Samedi 15 octobre : Grand Jorat (VD) – type classique Samedi 22 octobre : Pomier (74) – type classique Samedi 5 novembre : Echallens (VD) – type classique Samedi 12 novembre : CERN (GE) - sprint - Finale Généralement cinq circuits sont disponibles : ceci va du facile court (2 km) adapt&eacu...

  14. Orienting hypnosis.

    Science.gov (United States)

    Hope, Anna E; Sugarman, Laurence I

    2015-01-01

    This article presents a new frame for understanding hypnosis and its clinical applications. Despite great potential to transform health and care, hypnosis research and clinical integration is impaired in part by centuries of misrepresentation and ignorance about its demonstrated efficacy. The authors contend that advances in the field are primarily encumbered by the lack of distinct boundaries and definitions. Here, hypnosis, trance, and mind are all redefined and grounded in biological, neurological, and psychological phenomena. Solutions are proposed for boundary and language problems associated with hypnosis. The biological role of novelty stimulating an orienting response that, in turn, potentiates systemic plasticity forms the basis for trance. Hypnosis is merely the skill set that perpetuates and influences trance. This formulation meshes with many aspects of Milton Erickson's legacy and Ernest Rossi's recent theory of mind and health. Implications of this hypothesis for clinical skills, professional training, and research are discussed.

  15. An introduction to the tools hosted in the Bilbao Crystallographic Server

    Directory of Open Access Journals (Sweden)

    Aroyo M.I.

    2012-03-01

    Full Text Available The programs hosted in the Bilbao Crystallographic Server (http://www.cryst.ehu.es are briefly explained along with worked examples on various cases related to different fields of applications. It is our aim to have this text acting as a primer on the various usage of the crystallographic tools in conjunction with each other due to the modular structure of the server. For this reason, diverse topics such as crystallographic groups and their subgroups, pseudosymmetry, extinction conditions, k-vectors and irreducible representations have been discussed in the context.

  16. Crystallographic structure of ubiquitin in complex with cadmium ions

    Directory of Open Access Journals (Sweden)

    Cheung Peter

    2009-12-01

    Full Text Available Abstract Background Ubiquitination plays a critical role in regulating many cellular processes, from DNA repair and gene transcription to cell cycle and apoptosis. It is catalyzed by a specific enzymatic cascade ultimately leading to the conjugation of ubiquitin to lysine residues of the target protein that can be the ubiquitin molecule itself and to the formation of poly-ubiquitin chains. Findings We present the crystal structure at 3.0 Å resolution of bovine ubiquitin crystallized in presence of cadmium ions. Two molecules of ubiquitin are present in the asymmetric unit. Interestingly this non-covalent dimeric arrangement brings Lys-6 and Lys-63 of each crystallographically-independent monomer in close contact with the C-terminal ends of the other monomer. Residues Leu-8, Ile-44 and Val-70 that form a hydrophobic patch at the surface of the Ub monomer are trapped at the dimer interface. Conclusions The structural basis for signalling by poly-Ub chains relies on a visualization of conformations of alternatively linked poly-Ub chains. This arrangement of ubiquitin could illustrate how linkages involving Lys-6 or Lys-63 of ubiquitin are produced in the cell. It also details how ubiquitin molecules can specifically chelate cadmium ions.

  17. Cassia grandis Linn. f. seed galactomannan: structural and crystallographical studies.

    Science.gov (United States)

    Joshi, Harsha; Kapoor, Virendra P

    2003-09-01

    Cassia grandis is a small or medium sized tree, found in abundance throughout India. The seeds contain about 50% endosperm gum and possess the characteristics of becoming a potential source of seed gum. The purified polysaccharide has been characterized as a pure galactomannan having a mannose-galactose ratio of 3.15; molecular weight (Mw) 80,200; polydispersity (Mw/Mn), 1.35 and intrinsic viscosity [eta], 848 mL/g. Methylation, periodate oxidation, Smith degradation and 13C NMR studies confirm that the polysaccharide has the basic structure of legume galactomannans consisting of a beta-(1-->4)-linked main mannan backbone to which galactose units are attached at O-6. The orthorhombic lattice constants of the hydrated gum are as follows: a=9.00, b=24.81, c=10.30 A. The crystallographic data establish that the probable space group symmetry of the unit cell is P2(1)2(1)2. The results are in contradiction to earlier reports (Indian J. Chem. 16B (1978) 966; J. Indian Chem. Soc. 55 (1978) 1216) in which a non-galactomannan polysaccharide structure has been assigned having a main chain of (1-->4)-linked galactose and mannose units in the molar ratio 6:3, where 50% of the galactose units branched with two galactose and one mannose through 1-->3 linkage.

  18. Crystallographic analysis of amorphization caused by ion irradiation

    CERN Document Server

    Nakagawa, S T; Ono, T; Hada, Y; Betz, G

    2003-01-01

    Ion irradiation often causes amorphization in a crystal. We have presented a new crystallographic analysis that defines a new type of order parameter, which we call pixel mapping (PM). PM can describe algebraically to what extent and how the crystallinity has changed under ion bombardment. In other words, PM describes the long-range-order (LRO) interactions, based on the crystallography. PM can be effectively used, when it is incorporated in a classical molecular dynamics (MD) calculation. In the case of B ions implanted into a Si crystal, we observed crystal to amorphous (CA) transitions under energetic ion bombardment at low temperature. The PM profiling was more effective to reveal the CA transition than other atomistic methods of analyses as radial distribution function g(r) or vacancy mapping N sub v. PM could distinguish between perfect crystalline states, transition states, and random states. Moreover, PM revealed that the lattice reaction was cooperative even in a mesoscopic volume, e.g. in a cube of ...

  19. Crystallization and preliminary crystallographic analysis of recombinant human galectin-1

    Energy Technology Data Exchange (ETDEWEB)

    Scott, Stacy A. [Institute for Glycomics, Gold Coast Campus, Griffith University, Queensland 4222 (Australia); Scott, Ken [School of Biological Sciences, University of Auckland, Auckland (New Zealand); Blanchard, Helen, E-mail: h.blanchard@griffith.edu.au [Institute for Glycomics, Gold Coast Campus, Griffith University, Queensland 4222 (Australia)

    2007-11-01

    Human galectin-1 has been cloned, expressed in E. coli, purified and crystallized in the presence of both lactose (ligand) and β-mercaptoethanol under six different conditions. The X-ray diffraction data obtained have enabled the assignment of unit-cell parameters for two novel crystal forms of human galectin-1. Galectin-1 is considered to be a regulator protein as it is ubiquitously expressed throughout the adult body and is responsible for a broad range of cellular regulatory functions. Interest in galectin-1 from a drug-design perspective is founded on evidence of its overexpression by many cancers and its immunomodulatory properties. The development of galectin-1-specific inhibitors is a rational approach to the fight against cancer because although galectin-1 induces a plethora of effects, null mice appear normal. X-ray crystallographic structure determination will aid the structure-based design of galectin-1 inhibitors. Here, the crystallization and preliminary diffraction analysis of human galectin-1 crystals generated under six different conditions is reported. X-ray diffraction data enabled the assignment of unit-cell parameters for crystals grown under two conditions, one belongs to a tetragonal crystal system and the other was determined as monoclinic P2{sub 1}, representing two new crystal forms of human galectin-1.

  20. Phormidium phycoerythrin forms hexamers in crystals: a crystallographic study.

    Science.gov (United States)

    Sonani, Ravi Raghav; Sharma, Mahima; Gupta, Gagan Deep; Kumar, Vinay; Madamwar, Datta

    2015-08-01

    The crystallographic analysis of a marine cyanobacterium (Phormidium sp. A09DM) phycoerythrin (PE) that shows distinct sequence features compared with known PE structures from cyanobacteria and red algae is reported. Phormidium PE was crystallized using the sitting-drop vapour-diffusion method with ammonium sulfate as a precipitant. Diffraction data were collected on the protein crystallography beamline at the Indus-2 synchrotron. The crystals diffracted to about 2.1 Å resolution at 100 K. The crystals, with an apparent hexagonal morphology, belonged to space group P1, with unit-cell parameters a = 108.3, b = 108.4 Å, c = 116.6 Å, α = 78.94, β = 82.50, γ = 60.34°. The molecular-replacement solution confirmed the presence of 12 αβ monomers in the P1 cell. The Phormidium PE elutes as an (αβ)3 trimer of αβ monomers from a molecular-sieve column and exists as [(αβ)3]2 hexamers in the crystal lattice. Unlike red algal PE proteins, the hexamers of Phormidium PE do not form higher-order structures in the crystals. The existence of only one characteristic visual absorption band at 564 nm suggests the presence of phycoerythrobilin chromophores, and the absence of any other types of bilins, in the Phormidium PE assembly.

  1. Correlating Atom Probe Crystallographic Measurements with Transmission Kikuchi Diffraction Data.

    Science.gov (United States)

    Breen, Andrew J; Babinsky, Katharina; Day, Alec C; Eder, K; Oakman, Connor J; Trimby, Patrick W; Primig, Sophie; Cairney, Julie M; Ringer, Simon P

    2017-03-14

    Correlative microscopy approaches offer synergistic solutions to many research problems. One such combination, that has been studied in limited detail, is the use of atom probe tomography (APT) and transmission Kikuchi diffraction (TKD) on the same tip specimen. By combining these two powerful microscopy techniques, the microstructure of important engineering alloys can be studied in greater detail. For the first time, the accuracy of crystallographic measurements made using APT will be independently verified using TKD. Experimental data from two atom probe tips, one a nanocrystalline Al-0.5Ag alloy specimen collected on a straight flight-path atom probe and the other a high purity Mo specimen collected on a reflectron-fitted instrument, will be compared. We find that the average minimum misorientation angle, calculated from calibrated atom probe reconstructions with two different pole combinations, deviate 0.7° and 1.4°, respectively, from the TKD results. The type of atom probe and experimental conditions appear to have some impact on this accuracy and the reconstruction and measurement procedures are likely to contribute further to degradation in angular resolution. The challenges and implications of this correlative approach will also be discussed.

  2. Estimating exponential scheduling preferences

    DEFF Research Database (Denmark)

    Hjorth, Katrine; Börjesson, Maria; Engelson, Leonid

    time by maximising expected total utility over the day, their departure times are conditional on rates of utility derived at these locations. For forecasting and economic evaluation of planning alternatives, it is desirable to have simple forms of utility rates with few parameters. Several forms...... the travel time is random, Noland and Small (1995) suggested using expected utility theory to derive the reduced form of expected travel time cost that includes the cost of TTV. For the α-β-γ formulation of scheduling preferences and exponential or uniform distribution of travel time, Noland and Small (1995....... The purpose of this paper is to explore how well these scheduling preferences explain behaviour, compared to other possible scheduling models, and whether empirical estimation of the more complex exponential scheduling preferences is feasible. We use data from a stated preference survey conducted among car...

  3. Estimating exponential scheduling preferences

    DEFF Research Database (Denmark)

    Hjorth, Katrine; Börjesson, Maria; Engelson, Leonid

    time by maximising expected total utility over the day, their departure times are conditional on rates of utility derived at these locations. For forecasting and economic evaluation of planning alternatives, it is desirable to have simple forms of utility rates with few parameters. Several forms...... the travel time is random, Noland and Small (1995) suggested using expected utility theory to derive the reduced form of expected travel time cost that includes the cost of TTV. For the α-β-γ formulation of scheduling preferences and exponential or uniform distribution of travel time, Noland and Small (1995....... The purpose of this paper is to explore how well these scheduling preferences explain behaviour, compared to other possible scheduling models, and whether empirical estimation of the more complex exponential scheduling preferences is feasible. We use data from a stated preference survey conducted among car...

  4. Preferred axis in cosmology

    CERN Document Server

    Zhao, Wen

    2016-01-01

    The foundation of modern cosmology relies on the so-called cosmological principle which states an homogeneous and isotropic distribution of matter in the universe on large scales. However, recent observations, such as the temperature anisotropy of the cosmic microwave background (CMB) radiation, the motion of galaxies in the universe, the polarization of quasars and the acceleration of the cosmic expansion, indicate preferred directions in the sky. If these directions have a cosmological origin, the cosmological principle would be violated, and modern cosmology should be reconsidered. In this paper, by considering the preferred axis in the CMB parity violation, we find that it coincides with the preferred axes in CMB quadrupole and CMB octopole, and they all align with the direction of the CMB kinematic dipole. In addition, the preferred directions in the velocity flows, quasar alignment, anisotropy of the cosmic acceleration, the handedness of spiral galaxies, and the angular distribution of the fine-structu...

  5. Student Preferences in Typography.

    Science.gov (United States)

    Bell, Richard C.; Sullivan, James L. F.

    1981-01-01

    Describes a study in which 245 university students ranked their preferences among typographical variants of typeface, size, emphasis, and interline space in 16 paragraphs. Six references are listed. (CHC)

  6. An empirical investigation of German tourist anglers’ preferences for angling in Denmark

    DEFF Research Database (Denmark)

    Bonnichsen, Ole; Jensen, Carsten Lynge; Olsen, Søren Bøye

    at the site. To attract tourist anglers an angling site manager may use this information to target marketing efforts towards segments of tourist that prefer the type and quality of angling characteristics of the angling site in the managers possession. Additionally, he may seek to adjust and improve...... for environmental attributes, catch attributes, and social relation/distance attributes of the angling site. We find that preferences are heterogeneous across different angler segments. Three distinct segments of tourist anglers are identified, characterised as “catch oriented" anglers (57 %), “nature oriented......” anglers (24 %) and “trophy oriented anglers (19 %)”. All three angler segments have the strong preferences for water quality. However, they differ with respect to catch preferences and preferences for social interaction on the angling site. The catch oriented focus on the hunting aspects of angling...

  7. Preference for newspaper size.

    Science.gov (United States)

    Tsang, Steve N H; Hoffmann, Errol R; Chan, Alan H S

    2014-05-01

    The past few years has seen a change in the size of newspapers, with publishers moving to a smaller size format. Five 'standard' newspaper sizes are used in different countries: Broadsheet, Rhensch, Tabloid, Tall Tabloid and Berliner. These papers vary in both width and height of pages and hence there are implications for human reading comfort, which may be dependent on reading location such as on a lounge chair or on a train. Experiments were carried out to determine preferences for the different sizes and to relate these preferences to the geometric characteristics of the newspapers. For both comfortable and cramped/uncomfortable reading conditions, the rank order of preference for paper types was, from least to most-preferred, Broadsheet, Rhensch, Berliner, Tall Tabloid and Tabloid. Preferences were much stronger when determined in cramped/uncomfortable reading conditions, where most comparisons were significantly different. There was good correlation between participant ratings on several scales and preference, where most factors were related to comfort of holding and controlling the paper. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  8. Indian dental students' preferences regarding lecture courses.

    Science.gov (United States)

    Parolia, Abhishek; Mohan, Mandakini; Kundabala, M; Shenoy, Ramya

    2012-03-01

    Teaching and learning activities in the dental clinic or hospital are a challenging area for students as well as teachers. With various teaching methodologies being used in dental schools around the world, gaining greater understanding of students' attitudes toward these methodologies would be useful for dental educators. The objective of this study was to explore the preferences of dental students in India about various aspects of lecture courses. A structured survey consisting of ten closed-ended questions was developed, and 2,680 undergraduate students from forty-three dental schools in India were approached via e-mail with a follow-up postal mailing. Of these, 1,980 students responded, for a response rate of 73.8 percent. Most of the students reported preferring lectures with the aid of PowerPoint and chalkboard. They preferred morning lectures from 8 am to 10 am for a maximum of thirty to forty minutes for each lecture, and they preferred to receive information about the lecture topic in advance. The students said that delivery of clinical demonstrations was beneficial after the lectures, and they preferred learning-based rather than exam-oriented education. The respondents also said that attendance should be made compulsory and that numerical marking of examinations should not be replaced by a grading system.

  9. Visual cells remember earlier applied target: plasticity of orientation selectivity.

    Directory of Open Access Journals (Sweden)

    Narcis Ghisovan

    Full Text Available BACKGROUND: A canonical proposition states that, in mature brain, neurons responsive to sensory stimuli are tuned to specific properties installed shortly after birth. It is amply demonstrated that that neurons in adult visual cortex of cats are orientation-selective that is they respond with the highest firing rates to preferred oriented stimuli. METHODOLOGY/PRINCIPAL FINDINGS: In anesthetized cats, prepared in a conventional fashion for single cell recordings, the present investigation shows that presenting a stimulus uninterruptedly at a non-preferred orientation for twelve minutes induces changes in orientation preference. Across all conditions orientation tuning curves were investigated using a trial by trial method. Contrary to what has been previously reported with shorter adaptation duration, twelve minutes of adaptation induces mostly attractive shifts, i.e. toward the adapter. After a recovery period allowing neurons to restore their original orientation tuning curves, we carried out a second adaptation which produced three major results: (1 more frequent attractive shifts, (2 an increase of their magnitude, and (3 an additional enhancement of responses at the new or acquired preferred orientation. Additionally, we also show that the direction of shifts depends on the duration of the adaptation: shorter adaptation in most cases produces repulsive shifts, whereas adaptation exceeding nine minutes results in attractive shifts, in the same unit. Consequently, shifts in preferred orientation depend on the duration of adaptation. CONCLUSION/SIGNIFICANCE: The supplementary response improvements indicate that neurons in area 17 keep a memory trace of the previous stimulus properties, thereby upgrading cellular performance. It also highlights the dynamic nature of basic neuronal properties in adult cortex since repeated adaptations modified both the orientation tuning selectivity and the response strength to the preferred orientation. These

  10. Orienteering Club

    CERN Multimedia

    Club d'orientation

    2011-01-01

    Coupe genevoise, suite Résultats de la course de Saint-Cergue, sur la carte Les Pralies, samedi 17 septembre. Nouvelle victoire du finlandais Ville Keskisaari, du club COLJ sur le parcours technique long avec une belle avance sur le deuxième concurrent Christophe Vuitton du CO CERN. David Cuenin a remporté le parcours technique moyen, Franck Lonchampt du club O’Jura a, lui aussi, remporté à nouveau le parcours technique court, tout comme Julien Vuitton du club CO CERN sur le facile moyen. Pour finir, Stéphane Clément devance Victor Dannecker sur le parcours facile court. Les résultats complets sont disponibles sur le site du club du CERN http://cern.ch/club-orientation. Un abonnement est pris sur le secteur de Saint-Cergue, puisque le club organise les deux prochaines étapes de la coupe genevoise dans le Haut-Jura suisse. Tout d’abord le samedi 24 septembre, un relais inter-club se courr...

  11. Orienteering club

    CERN Multimedia

    Club d'orientation

    2010-01-01

    COURSE D’ORIENTATION  De La Rippe à Sauvabellin, la coupe genevoise continue ! Le rendez-vous était donné samedi 8 mai aux amateurs de course d’orientation dans les bois de La Rippe (Canton de Vaud). Cette 6e épreuve était organisée par le Club Satus Grutli de Genève. Il est dommage que les participants n’aient pas été aussi nombreux que lors des dernières courses, les Championnats de France des clubs à Dijon ayant certainement retenus plus d’un compétiteur. La première place est revenue à : – Technique long : Berni Wehrle – Technique moyen : Jean-Bernard Zosso – Technique court : Berni Wehrle – Facile moyen : Peter Troscanyi – Facile court : Claire Droz. Il ne restera plus que deux épreuves ...

  12. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2012-01-01

    Course d'orientation Ces deux dernières semaines, le club a organisé la troisième puis la quatrième étape de la coupe de printemps, une dans la forêt de Collogny/Moissey près de Vulbens, l’autre vers le parcours vita de Trélex. Les résultats sont: Facile court Vulbens : 1er Léo Lonchampt, O’Jura (16:04), 2e Timothée Bazin (23:07), 3e Francesco Pieri (26:57) Trélex : 1er Noora Maurent (23:11), 2e Sarah Stuber, COLJ (26:51), 3e T. Bazin (28:17) Facile moyen Vulbens : 1er Victor Kuznetsov, CO CERN (25:36), 2e Didier Descourvières (28:03), 3e Konstantinos Haider, CO CERN (36:53) Trélex : 1er V. Kuznetsov, COLJ (38:01), 2e K. Haider, CO CERN (43:15), 3e ex aequo Olivia Nguyen et Sven Vietmeier (58:11) Technique court Vulbens : 1er Benoit Bazin (41:21), 2e Colas Gintzburger (55:12), 3e Nathan Freydoz (55:48) Trélex : 1...

  13. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2011-01-01

    Course d'orientation Avec la CO en nocturne organisée par le club du CERN vendredi 14 octobre au stade des Eveaux (Ge), et la CO à Savigny (Vd) proposée par le club de Lausanne-Jorat le lendemain, les étapes de la coupe genevoise d’automne s’enchainent rapidement. Il ne reste plus que 3 rendez-vous pour boucler la saison. Les premières places devraient certainement se jouer entre des membres du club du CERN, du O’Jura ou de Lausanne-Jorat. La prochaine course du club est programmée pour samedi 22 octobre à Pomier, près de Cruseilles. L’accueil se fera à partir de 12h30 et les départs s’échelonneront de 13h à 15h. * * * * * * * Nouvelle belle victoire samedi 8 octobre à Saint Cergue du jeune finlandais Ville Keskisaari (COLJ) en 50:56 devant Jürg Niggli (O’Jura) en 1:03:32, et Alexandre...

  14. Orienteering club

    CERN Multimedia

    Club d'orientation

    2013-01-01

    Course d'orientation Finale de la coupe genevoise Rapide et méthodique, voilà les qualités dont il fallait faire preuve pour remporter la dernière étape de la coupe organisée par le club du CERN dans les bois de Monteret. Il s’agissait d’une course au score où chaque concurrent disposait d’un temps imparti pour poinçonner le maximum de balises. Le parcours technique a été remporté par Tomas Shellman et le parcours facile par Victor Dannecker. Cette dernière étape était aussi décisive pour la désignation des lauréats de la coupe genevoise de printemps. Les résultats officiels étaient donnés par le président du club, L. Jirden : Circuit Technique Long : Berni Wehrle, Bruno Barge, Edvins Reisons Circuit Technique Moyen : J.-Bernard Zosso, ...

  15. Orienteering Club

    CERN Multimedia

    Club d'orientation

    2013-01-01

    De jour comme de nuit Les amateurs de course d’orientation ont pu s’en donner à cœur joie ce week-end puisqu’ils avaient la possibilité de courir sur deux épreuves en moins de 24 heures. En effet, le club du CERN organisait une course de nuit aux Evaux et la 7e étape de la coupe genevoise se tenait samedi après-midi dans les bois du Grand Jorat à Savigny. Les vainqueurs pour chaque course sont : Technique long CO de nuit: Julien Charlemagne, SOS Sallanches CO samedi: Philipp Khlebnikov, ANCO   Technique moyen CO de nuit: Céline Zosso, CO CERN CO samedi: Pavel Khlebnikov, ANCO Technique court CO de nuit: Colas Ginztburger, SOS Sallanches CO samedi: Victor Kuznetsov, COLJ Lausannne Facile moyen CO de nuit: Gaëtan Rickenbacher, CO CERN CO samedi: Tamas Szoke   Facile court CO de nuit:Oriane Rickenbacher, CO CERN CO samedi: Katya Kuznetsov...

  16. Orienteering club

    CERN Multimedia

    Club d'orientation

    2014-01-01

    Course d'orientation Finale de la coupe d’automne La dernière épreuve de la coupe d’automne organisée par le club s’est déroulée ce samedi 1er novembre avec une course type «one-man-relay» dans la forêt de Trelex (Vd). Les concurrents des circuits techniques devaient parcourir trois boucles et ceux des circuits «faciles» deux boucles, avec changements de carte. Le parcours technique long a été remporté par un membre du club, Berni Wehrle. A l’issue de cette course, le Président du club, L. Jirden annonçait le classement général de la coupe d’automne, basé sur les 6 meilleurs résultats de la saison : Circuit technique long : 1er Juerg Niggli (O’Jura), 2e Berni Wehrle, 3e Beat Mueller. Circuit technique moyen : 1er Laurent Merat (O&r...

  17. Orienteering Club

    CERN Multimedia

    Club d'orientation

    2012-01-01

    Finale de la coupe d’automne   La coupe d’automne organisée par le club d’orientation du CERN s’est terminée ce samedi 10 novembre avec une course sprint à Prévessins. C’était la 12e épreuve de la saison. En stage dans la région, Tanya Ryabkina, championne d’Europe en titre et médaillée de bronze en moyenne distance lors des championnats du monde à La Givrine cet été, a fait l’honneur de sa présence et termine 2e à 8 secondes de Trygve Buanes, norvégien du club de Bergen. A l’issue de cette dernière épreuve, le classement général de la coupe d’automne, basé sur les 8 meilleurs résultats de la saison, est ainsi le suivant : Circuit technique long : 1er Jurg Niggli (O&rsqu...

  18. Orienteering Club

    CERN Multimedia

    Club d'orientation

    2013-01-01

    Finale de la coupe d’automne La dernière épreuve de la coupe d’automne organisée par le club d’orientation du CERN s’est déroulée ce samedi 2 novembre avec une course au score dans le bois Tollot (GE). Les concurrents disposaient d’un temps imparti pour poinçonner le maximum de balises différemment placées selon le circuit choisi. Juerg Niggli (club O’Jura) a remporté le parcours technique long. A l’issue de cette course, le classement général de la coupe d’automne, basé sur les 6 meilleurs résultats de la saison, est le suivant : Circuit technique long : 1er Juerg Niggli (O’Jura), 2e Bruno Barge, 3e Beat Mueller. Circuit technique moyen : 1er Laurent Merat (O’Jura), 2e Jirden Lennart, 3e Daria Niggli. Circuit technique court : 1er Victor Kuznetsov (COLJ), 2e N...

  19. Orienteering club

    CERN Multimedia

    Club d'orientation

    2013-01-01

    Course d'orientation Vers les dernières courses de printemps Une centaine de coureurs se sont déplacés sur le site de la Roche Fendue prés de Morez pour gouter à un des 5 parcours proposés par le club du O’Jura. Le terrain était gras mais que peut-on trouver d’autre avec cette météo! Les vainqueurs de chaque circuit sont : Alina Niggli (O’Jura) facile court, Natalja Niggli (O’Jura) facile moyen, Victor Kuznetsov (COLJ) technique court, Yves Rousselot (Balise 25) technique moyen et pour finir François Gonon (O’Jura) avec une victoire haut la main sur le technique long. Il ne reste plus que deux épreuves pour la coupe genevoise de printemps : à savoir samedi 8 juin, course de type longue distance organisée par le club de Lausanne Jorat (COLJ) dans le bois de Seyte sur Mutrux/Concise, inscription de 12h &...

  20. Orienteering Club

    CERN Multimedia

    Club d'orientation

    2013-01-01

    Course d'orientation Le coup d’envoi de la coupe genevoise a été donné samedi 31 août dans les bois de Combe Froide à Prémanon. Plus de 150 coureurs avaient fait le déplacement. Les parcours facile court, facile moyen et technique court ont été remportés par des coureurs du club O’Jura - Ulysse Dannecker, Léo Lonchampt, Franck Lonchampt, le technique moyen par Pekka Marti du club Ol Biel Seeland et le technique long par Térence Risse du CA Rosé – également membre de l’équipe nationale suisse des moins de 20 ans. Pour le club du CERN, les meilleures résultats ont été obtenus pas Emese Szunyog sur technique court et Marie Vuitton sur technique moyen avec une 4e place. La prochaine course aura lieu samedi 14 septembre à La Faucille. Le club propose aussi...

  1. Orienteering Club

    CERN Multimedia

    CLUB D'ORIENTATION

    2013-01-01

    Calendrier de la coupe d’automne Le Club d’orientation du CERN, en partenariat avec d’autres clubs de la région, vous propose, pour cette nouvelle coupe d’automne genevoise, une série de 10 courses. Le club du O’Jura donnera le coup d’envoi le samedi 31 août. Les courses s’enchaîneront selon le calendrier suivant : Samedi 31 août : Prémanon (39) - longue distance Samedi 14 septembre : La Faucille (01) - longue distance Samedi 21 septembre : Saint Cergue (VD) - longue distance Samedi 28 septembre : Ballens (VD) - relais Samedi 5 octobre : La Pile (VD) - longue distance Vendredi 11 octobre : Les Evaux (GE) - nocturne Samedi 12 octobre : Grand Jorat, Savigny (VD) - longue distance Samedi 19 octobre : Terrasses de Genève (74) - longue distance Samedi 26 octobre : Prémanon (39) - longue distance Samedi 2 novembre : Bois Tollot (GE) - score - Finale Les &a...

  2. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2012-01-01

    Relais inter-club/Challenge Carlo Milan Samedi dernier, lors de l’épreuve de course d’orientation organisée par le club du O’Jura, le moteur de la discipline était l’esprit d’équipe, puisqu’il était question d’un relais inter-club avec le Challenge Carlo Milan. Les clubs avaient aligné leurs coureurs soit sur le relais technique (trois participants) soit sur le relais facile (deux participants). Côté O’Jura, il fallait noter la participation de François Gonon, champion du monde 2011, côté club du CERN, Marie et Gaëtan Vuitton, jeunes espoirs du club, devaient préparer la piste pour lancer le dernier relayeur. Côté Lausanne-Jorat, il fallait compter sur le très jeune Viktor Kuznetsov. Les 31 équipes engagées n’ont pas m&ea...

  3. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2012-01-01

     Finale de la coupe de printemps   La dernière course d’orientation comptant pour la Coupe de printemps a eu lieu samedi dernier dans le village des Rousses et vers le Fort. Il s’agissait d’un sprint organisé par le club O’Jura. Les temps de course ont avoisiné les 20 minutes que ce soit pour le parcours technique moyen ou technique long. Tous les habitués étaient au rendez-vous pour venir consolider ou améliorer leur place au classement. A l’issue de cette course, le classement général de la Coupe de printemps prenant en compte les 6 meilleurs résultats des 9 courses était établi et les lauréats de chaque catégorie sont les suivants: Circuit technique long : 1er Berni Wehrle, 2e Bruno Barge, 3e Edvins Reisons. Circuit technique moyen : 1er Jean-Bernard Zosso, 2e Cédric Wehrl&...

  4. Orienteering Club

    CERN Multimedia

    Club d'Orientation

    2015-01-01

    Course orientation Finale de la coupe genevoise La série des courses de printemps s’est achevée samedi dernier dans les bois de Bonmont (Vaud) avec une épreuve «one-man-relay» organisée par le club. Le vainqueur du parcours technique  long, Yann Locatelli (Club de Chambéry Savoie) a réalisé les deux boucles comportant 24 balises avec presque 6 minutes d’avance sur le second concurrent Domenico Lepori (Club CARE Vevey). Cette dernière étape était aussi décisive pour la désignation des lauréats de la coupe genevoise de printemps, en comptabilisant les 6 meilleurs résultats sur les 10 épreuves. Le podium officiel était donné par le président du club, L. Jirden, qui profitait de l’occasion pour remercier tous les participants et également tous les...

  5. Orienteering club

    CERN Multimedia

    Club d'orientation

    2013-01-01

    Courses d’orientation Samedi 20 avril, les organisateurs du Club de CO du CERN ont accueilli au Mont Mourex 70 participants qui n’ont pas hésité à venir malgré la forte bise. Berni Wehrle du CO CERN s’est octroyé la première place en 1:04:49 sur le parcours technique long devant Pyry Kettunen du Saynso Juankoski en 1:06:52, la 3e place revenant à Bruno Barge, CO CERN, à 7 secondes. Les autres parcours ont été remportés par : Technique moyen : 1er Jacques Moisset, Chamonix (47:44), 2e Yves Rousselot, Balise 25 Besançon (57:16), 3e Jean-Bernard Zosso, CO CERN (59:28). Technique court : 1er Victor Kuznetsov, COLJ (51:53), 2e Pierrick Collet, CO CERN (1:12:52), 3e Dominique Balay, CO CERN (1:16:04). Pour les parcours facile moyen et facile court, Ralf Nardini et Léa Nicolas, tous deux du CO CERN, terminaient respectivement premier. Voi...

  6. Orienteering club

    CERN Multimedia

    Club d'orientation

    2014-01-01

    Course d'orientation C’est sous un beau soleil samedi 4 octobre que s’est déroulée la 6e étape de la Coupe genevoise d’automne organisée par le club. Plus d’une centaine de concurrents provenant de 7 clubs de CO avaient fait le déplacement pour courir sur un des cinq parcours proposés dans les bois de Trélex-Génolier (VD). Le podium est le suivant : Technique long (5,9 km, 19 postes) : 1er Jurg Niggli, O’Jura (1:00:02); 2e Berni Wehrle, CO CERN (1:06:44); 3e Konrad Ehrbar, COLJ (1:07:08) Technique moyen (4,8 km, 18 postes) : 1er Christophe Vuitton, CO CERN (54:25); 2e J.B. Zosso, CO CERN (1:01:19); 3e Jeremy Wichoud, COLJ (1:06:21) Technique court (3,8 km, 14 postes) : 1er Julien Vuitton, CO CERN (36:19); 2e Vladimir Kuznetsov, COLJ (48:47); 3e Natalia Niggli, O’Jura (50:38) Facile moyen (3,2 km, 11 postes) : 1ère Alina Niggli, O&...

  7. Erbium-ion implantation into various crystallographic cuts of Al{sub 2}O{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Nekvindova, P. [Department of Inorganic Chemistry, Institute of Chemical Technology, Technicka 5, 166 28 Prague 6 (Czech Republic); Mackova, A.; Malinsky, P. [Nuclear Physics Institute of the Academy of Sciences of the Czech Republic v.v.i., 250 68 Rez (Czech Republic); Department of Physics, Faculty of Science, J.E. Purkinje University, Ceske mladeze 8, 400 96 Usti nad Labem (Czech Republic); Cajzl, J.; Svecova, B. [Department of Inorganic Chemistry, Institute of Chemical Technology, Technicka 5, 166 28 Prague 6 (Czech Republic); Oswald, J. [Institute of Physics, Academy of Sciences of the Czech Republic, v.v.i., Cukrovarnicka 10, 162 53 Prague (Czech Republic); Wilhelm, R.A. [Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden-Rossendorf, 01314 Dresden (Germany); Technische Universität Dresden, 01062 Dresden (Germany)

    2015-12-15

    This paper reports on the importance of crystallographic cuts with a different orientation on the luminescent properties and structural changes of Al{sub 2}O{sub 3} implanted with Er{sup +} ions at 190 keV and with a fluence of 1.0 × 10{sup 16} cm{sup −2}. Post-implantation annealing at 1000 °C in oxygen atmosphere was also done. The chemical compositions and erbium concentration-depth profiles of implanted layers were studied by Rutherford Backscattering Spectrometry (RBS) and compared to SRIM simulations. The same value of the maximum erbium concentration (up to 2 at.%) was observed at a depth of about 40 nm for all crystallographic cuts. The structural properties of the prepared layers were characterised by RBS/channelling. The relative amount of disordered atoms of 70–80% was observed in the prepared implanted layers and discussed for various cuts. It has been found that erbium is positioned randomly in the Al{sub 2}O{sub 3} crystalline matrix, and no preferential positions appeared even after the annealing procedure. Erbium luminescence properties were measured in the wavelength range of 1440–1650 nm for all samples. As-implanted Al{sub 2}O{sub 3} samples had a significant luminescence band at 1530 nm. The best luminescence was repeatedly observed in the 〈0 0 0 1〉 cut of Al{sub 2}O{sub 3}. The annealing procedure significantly improved the luminescent properties.

  8. Asymmetries in perception of 3D orientation.

    Directory of Open Access Journals (Sweden)

    Allan C Dobbins

    Full Text Available Visual scene interpretation depends on assumptions based on the statistical regularities of the world. People have some preference for seeing ambiguously oriented objects (Necker cubes as if tilted down or viewed from above. This bias is a near certainty in the first instant (approximately 1 s of viewing and declines over the course of many seconds. In addition, we found that there is modulation of perceived orientation that varies with position--for example objects on the left are more likely to be interpreted as viewed from the right. Therefore there is both a viewed-from-above prior and a scene position-dependent modulation of perceived 3-D orientation. These results are consistent with the idea that ambiguously oriented objects are initially assigned an orientation consistent with our experience of an asymmetric world in which objects most probably sit on surfaces below eye level.

  9. Crystallographic control on the substructure of nacre tablets.

    Science.gov (United States)

    Checa, Antonio G; Mutvei, Harry; Osuna-Mascaró, Antonio J; Bonarski, Jan T; Faryna, Marek; Berent, Katarzyna; Pina, Carlos M; Rousseau, Marthe; Macías-Sánchez, Elena

    2013-09-01

    Nacre tablets of mollusks develop two kinds of features when either the calcium carbonate or the organic portions are removed: (1) parallel lineations (vermiculations) formed by elongated carbonate rods, and (2) hourglass patterns, which appear in high relief when etched or in low relief if bleached. In untreated tablets, SEM and AFM data show that vermiculations correspond to aligned and fused aragonite nanogloblules, which are partly surrounded by thin organic pellicles. EBSD mapping of the surfaces of tablets indicates that the vermiculations are invariably parallel to the crystallographic a-axis of aragonite and that the triangles are aligned with the b-axis and correspond to the advance of the {010} faces during the growth of the tablet. According to our interpretation, the vermiculations appear because organic molecules during growth are expelled from the a-axis, where the Ca-CO3 bonds are the shortest. In this way, the subunits forming nacre merge uninterruptedly, forming chains parallel to the a-axis, whereas the organic molecules are expelled to the sides of these chains. Hourglass patterns would be produced by preferential adsorption of organic molecules along the {010}, as compared to the {100} faces. A model is presented for the nanostructure of nacre tablets. SEM and EBSD data also show the existence within the tablets of nanocrystalline units, which are twinned on {110} with the rest of the tablet. Our study shows that the growth dynamics of nacre tablets (and bioaragonite in general) results from the interaction at two different and mutually related levels: tablets and nanogranules.

  10. Measuring children's food preferences

    DEFF Research Database (Denmark)

    Olsen, Annemarie; Kildegaard, Heidi; Gabrielsen, Gorm

    2012-01-01

    The aim of this study is to investigate if children’s food preferences can be reliable measured by using pictures of foods presented on a computer screen in a conjoint layout.We investigate reproducibility (test–retest) and infer validity by comparison with traditional hedonic evaluations...... juices (tangible products), chosen to span the preference spectrum, were hedonically evaluated for appearance and taste. Finally, an actual product choice was performed by having the children choose between two buns and two juices.Results showed that the computer evaluationswith pictures of foods...... provided reproducible information about the children’s visual food preferences, which were in concordance with both hedonic measures and products choices, and can thus be considered valid....

  11. Situated embodied cognition: monitoring orientation cues affects product evaluation and choice

    NARCIS (Netherlands)

    J. Eelen; S. Dewitte; L. Warlop

    2013-01-01

    Consumers generally prefer products that are easy to interact with. In three studies, we show that this preference arises from the fit between product orientation and monitored situational constraints. Flexible right-handers, who monitor situational constraints, recall product orientations better an

  12. Estimating exponential scheduling preferences

    DEFF Research Database (Denmark)

    Hjorth, Katrine; Börjesson, Maria; Engelson, Leonid

    2015-01-01

    Different assumptions about travelers' scheduling preferences yield different measures of the cost of travel time variability. Only few forms of scheduling preferences provide non-trivial measures which are additive over links in transport networks where link travel times are arbitrarily...... of car drivers' route and mode choice under uncertain travel times. Our analysis exposes some important methodological issues related to complex non-linear scheduling models: One issue is identifying the point in time where the marginal utility of being at the destination becomes larger than the marginal...

  13. Revealed smooth nontransitive preferences

    DEFF Research Database (Denmark)

    Keiding, Hans; Tvede, Mich

    2013-01-01

    consumption bundle, all strictly preferred bundles are more expensive than the observed bundle. Our main result is that data sets can be rationalized by a smooth nontransitive preference relation if and only if prices can normalized such that the law of demand is satisfied. Market data sets consist of finitely...... many observations of price vectors, lists of individual incomes and aggregate demands. We apply our main result to characterize market data sets consistent with equilibrium behaviour of pure-exchange economies with smooth nontransitive consumers....

  14. Enzymes for carbon sequestration: neutron crystallographic studies of carbonic anhydrase

    Energy Technology Data Exchange (ETDEWEB)

    Fisher, S. Z., E-mail: zfisher@lanl.gov; Kovalevsky, A. Y. [Bioscience Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Domsic, J. [Department of Biochemistry and Molecular Biology, PO Box 100245, University of Florida, Gainesville, FL 32610 (United States); Mustyakimov, M. [Bioscience Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Silverman, D. N. [Department of Pharmacology and Therapeutics, PO Box 100267, University of Florida, Gainesville, FL 32610 (United States); McKenna, R. [Department of Biochemistry and Molecular Biology, PO Box 100245, University of Florida, Gainesville, FL 32610 (United States); Langan, P. [Bioscience Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2010-11-01

    The first neutron crystal structure of carbonic anhydrase is presented. The structure reveals interesting and unexpected features of the active site that affect catalysis. Carbonic anhydrase (CA) is a ubiquitous metalloenzyme that catalyzes the reversible hydration of CO{sub 2} to form HCO{sub 3}{sup −} and H{sup +} using a Zn–hydroxide mechanism. The first part of catalysis involves CO{sub 2} hydration, while the second part deals with removing the excess proton that is formed during the first step. Proton transfer (PT) is thought to occur through a well ordered hydrogen-bonded network of waters that stretches from the metal center of CA to an internal proton shuttle, His64. These waters are oriented and ordered through a series of hydrogen-bonding interactions to hydrophilic residues that line the active site of CA. Neutron studies were conducted on wild-type human CA isoform II (HCA II) in order to better understand the nature and the orientation of the Zn-bound solvent (ZS), the charged state and conformation of His64, the hydrogen-bonding patterns and orientations of the water molecules that mediate PT and the ionization of hydrophilic residues in the active site that interact with the water network. Several interesting and unexpected features in the active site were observed which have implications for how PT proceeds in CA.

  15. FMRI orientation decoding in V1 does not require global maps or globally coherent orientation stimuli

    Directory of Open Access Journals (Sweden)

    Arjen eAlink

    2013-08-01

    Full Text Available The orientation of a large grating can be decoded from V1 functional magnetic resonance imaging (fMRI data, even at low resolution (3-mm isotropic voxels. This finding has suggested that columnar-level neuronal information might be accessible to fMRI at 3T. However, orientation decodability might alternatively arise from global orientation-bias maps. Such global maps across V1 could result from bottom-up processing, if the preferences of V1 neurons were biased toward particular orientations (e.g. radial from fixation, or cardinal, i.e. vertical or horizontal. Global maps could also arise from local recurrent or top-down processing, reflecting pre-attentive perceptual grouping, attention spreading, or predictive coding of global form. Here we investigate whether fMRI orientation decoding with 2-mm voxels requires (a globally coherent orientation stimuli and/or (b global-scale patterns of V1 activity. We used opposite-orientation gratings (balanced about the cardinal orientations and spirals (balanced about the radial orientation, along with novel patch-swapped variants of these stimuli. The two stimuli of a patch-swapped pair have opposite orientations everywhere (like their globally coherent parent stimuli. However, the two stimuli appear globally similar, a patchwork of opposite orientations. We find that all stimulus pairs are robustly decodable, demonstrating that fMRI orientation decoding does not require globally coherent orientation stimuli. Furthermore, decoding remained robust after spatial high-pass filtering for all stimuli, showing that fine-grained components of the fMRI patterns reflect visual orientations. Consistent with previous studies, we found evidence for global radial and vertical bias maps in V1. However, these were weak or absent for patch-swapped stimuli, suggesting that global bias maps depend on globally coherent orientations and might arise through recurrent or top-down processes related to the perception of global

  16. TEACHING OBJECT ORIENTED PROGRAMMING AT THE INTRODUCTORY LEVEL

    OpenAIRE

    OKUR , Prof.Dr. Mehmet C.

    2006-01-01

    Teaching object oriented programming has become a rapidly expanding preference at various educational environments. However, teachers usually experience problems when introducing object oriented concepts and programming to beginners. How to teach the fundamentals of object oriented programming at an introductory level course is still a common subject for debate. In this paper, an evaluation of these problems is presented and some possible approaches for improving the quality and success of su...

  17. Energetic, crystallographic and diffusion characteristics of hydrogen isotopes in iron

    Energy Technology Data Exchange (ETDEWEB)

    Sivak, A.B., E-mail: sivak_ab@nrcki.ru [National Research Centre “Kurchatov Institute”, 1, Akademika Kurchatova pl., Moscow 123182 (Russian Federation); National Research Tomsk State University, 36, Lenina pr., Tomsk 634050 (Russian Federation); Sivak, P.A., E-mail: sivak_pa@nrcki.ru [National Research Centre “Kurchatov Institute”, 1, Akademika Kurchatova pl., Moscow 123182 (Russian Federation); Romanov, V.A., E-mail: romanov-ippe@mail.ru [National Research Tomsk State University, 36, Lenina pr., Tomsk 634050 (Russian Federation); A.I. Leypunski Institute of Physics and Power Engineering (IPPE), 1, Bondarenko pl., Obninsk, Kaluga reg. 249033 (Russian Federation); Chernov, V.M., E-mail: vmchernov@bochvar.ru [National Research Tomsk State University, 36, Lenina pr., Tomsk 634050 (Russian Federation); A.A. Bochvar High-technology Research Institute of Inorganic Materials (JSC “VNIINM”), 5-a, Rogova ul., PoB 369, Moscow 123098 (Russian Federation); National Research Nuclear University “MEPhI”, 31, Kashirskoye sh., Moscow 115409 (Russian Federation)

    2015-06-15

    Highlights: • H isotopes properties in Fe were calculated by molecular statics and dynamics methods. • The binding energies of complexes “H atoms – self-defects” were calculated. • Temperature dependencies of H isotopes diffusivities have parabolic form at T > 250 K. • There is a good agreement between MD and experimental data for protium diffusivity. • H isotopes diffusivities are within 10% at 293 K. Isotope effect increases with temperature. - Abstract: Energetic, crystallographic and diffusion characteristics of various interstitial configurations of H atoms and their complexes with self-point defects (SIA – self-interstitial atom, V – vacancy) in bcc iron have been calculated by molecular statics and molecular dynamics using Fe–H interatomic interaction potential developed by Ramasubramaniam et al. (2009) and modified by the authors of the present work and Fe–Fe matrix potential M07 developed by Malerba et al. (2010). The most energetically favorable configuration of an interstitial H atom is tetrahedral configuration. The energy barrier for H atom migration is 0.04 eV. The highest binding energy of all the considered complexes “vacancy – H atom” and “SIA – H atom” is 0.54 and 0.15 eV, respectively. The binding energy of H atom with edge dislocations in slip systems 〈1 1 1〉{1 1 0}, 〈1 1 1〉{1 1 2}, 〈1 0 0〉{1 0 0}, 〈1 0 0〉{1 1 0} is 0.32, 0.30, 0.45, 0.54 eV, respectively. The binding energy of H atom in VH{sub n} complexes (n = 1 … 15) decreases from 0.54 to 0.35 eV with increasing of n from 1 to 6. At n > 6, it decreases to ∼0.1 eV. The temperature dependences of hydrogen isotopes (P, D, T) diffusivities have been calculated for the temperature range 70–1800 K. Arrhenius-type dependencies describe the calculated data at temperatures T < 100 K. At T > 250 K, the temperature dependencies of the diffusivities D{sup P}, D{sup D}, D{sup T} have a parabolic form. The diffusivities of H isotopes are within 10

  18. Crystallographic transformation of limestone during calcination under CO2.

    Science.gov (United States)

    Valverde, Jose Manuel; Medina, Santiago

    2015-09-14

    The calcination reaction of limestone (CaCO3) to yield lime (CaO) is at the heart of many industrial applications as well as natural processes. In the recently emerged calcium-looping technology, CO2 capture is accomplished by the carbonation of CaO in a gas-solid reactor (carbonator). CaO is derived by the calcination of limestone in a calciner reactor under necessarily high CO2 partial pressure and high temperature. In situ X-ray diffraction (XRD) has been employed in this work to gain further insight into the crystallographic transformation that takes place during the calcination of limestone under CO2, at partial pressures (P) close to the equilibrium pressure (Peq) and at high temperature. Calcination under these conditions becomes extremely slow. The in situ XRD analysis presented here suggests the presence of an intermediate metastable CaO* phase stemming from the parent CaCO3 structure. According to the reaction mechanism proposed elsewhere, the exothermicity of the CaO* → CaO transformation and high values of P/Peq inhibit the nucleation of CaO at high temperatures. The wt% of CaO* remains at a relatively high level during slow calcination. Two diverse stages have been identified in the evolution of CaO crystallite size, L. Initially, L increases with CaCO3 conversion, following a logarithmic law. Slow calcination allows the crystallite size to grow up from a few nanometers at nucleation up to around 100 nm near the end of conversion. Otherwise, quick calcination at relatively lower CO2 concentrations limits CaO crystallite growth. Once calcination reaches an advanced state, the presence of CaO* drops to zero and the rate of increase of the CaO crystallite size is significantly hindered. Arguably, the first stage in CaO crystallite growth is driven by aggregation of the metastable CaO* nanocrystals, due to surface attractive forces, whereas the second one is consistent with sintering of the aggregated CaO crystals, and persists with time after full

  19. Collection Preferences of Children

    Science.gov (United States)

    Walls, Richard T.; And Others

    1975-01-01

    Eighty nursery school and upper elementary school children selected picture cards from varying stimulus arrays in order to indicate their preference for unorganized mixed collections, groups of identical cards, or sets of different cards that together formed a whole figure. (CW)

  20. FUZZY PREFERENCES IN CONFLICTS

    Institute of Scientific and Technical Information of China (English)

    Mubarak S. AL-MUTAIRI; Keith W. HIPEL; Mohamed S. KAMEL

    2008-01-01

    A systematic fuzzy approach is developed to model fuzziness and uncertainties in the preferences of decision makers involved in a conflict. This unique fuzzy preference formulation is used within the paradigm of the Graph Model for Conflict Resolution in which a given dispute is modeled in terms of decision makers, each decision maker's courses of actions or options, and each decision maker's preferences concerning the states or outcomes which could take place. In order to be able to determine the stability of each state for each decision maker and the possible equilibria or resolutions, a range of solution concepts describing potential human behavior under conflict are defined for use with fuzzy preferences. More specifically, strong and weak definitions of stability are provided for the solution concepts called Nash, general metarational, symmetric metarational, and sequential stability. To illustrate how these solution concepts can be conveniently used in practice, they are applied to a dispute over the contamination of an aquifer by a chemical company located in Elmira, Ontario, Canada.

  1. Preferred Dance Tempo

    DEFF Research Database (Denmark)

    Dahl, Sofia; Huron, David; Brod, Garvin

    2014-01-01

    In two experiments participants tuned a drum machine to their preferred dance tempo. Measurements of height, shoulder width, leg length, and weight were taken for each participant, and their sex recorded. Using a multiple regression analysis, height and leg length combined was found to be the bes...

  2. Patterns of Environmental Preference

    Science.gov (United States)

    Kaplan, Rachel

    1977-01-01

    This study sought to evaluate components of the Environmental Preference Questionnaire (EPQ). The 267 teenagers who completed the EPQ in this study also responded to questions relating to facets of self esteem and the reasons for selecting their favorite activities. (BT)

  3. Arm chair perspective preferences

    NARCIS (Netherlands)

    Koenderink, Jan; van Doorn, A.J.; Pinna, Baingio; Pepperell, Robert

    2016-01-01

    Do generic observers in their free-style viewing of postcard-size pictures have a preference for specific modes of perspective rendering? This most likely depends upon the phrasing of the question. Here we consider the feeling of ‘presence’: does the observer experience a sense of being ‘immersed in

  4. Automated determination of crystal orientations from electron backscattering patterns

    DEFF Research Database (Denmark)

    Lassen, Niels Christian Krieger

    1994-01-01

    determination of crystallographic orientations from EBSPs is accurate knowledge of three calibration parameters which describe the position of the point from which the patterns are emitted relative to the phosphor screen on which they are recorded. This thesis will describe a novel method by which...... of the position of the bands or the zone axes of EBSPs have existed for several years now. Until recently, however, the localization of either the bands or the zone axes of EBSPs has required the valuable time and attention of a human operator, thus obviously limiting the amounts of orientation data that can...... these calibration parameters can be estimated with high precision. The quality of EBSPs provides important information about the reliability of the measured crystal orientations and about the perfection of the lattice in which the pattern is generated. A measure which allows the quality of EBSPs to be evaluated...

  5. Considering the role of conditioning in sexual orientation.

    Science.gov (United States)

    Hoffmann, Heather

    2012-02-01

    The effects of learning on sexual orientation are rarely addressed in the literature. At the very least, such processes provide a means of elaborating upon orientation predispositions. Some aspects of our mates may inherently elicit a sexual response, but other attributes do so only after sexual experience with them. Animal research shows robust, direct effects of conditioning processes on partner preference with a few studies showing plasticity in preference for sex of partner. Descriptive research in humans suggests effects of experience on partner preference and, although experimental demonstrations of human sexual conditioning are neither numerous nor robust, sexual arousal is conditionable in women and men. With modern developments in learning theory (e.g., expectancy learning and evaluative conditioning), it seems appropriate to renew the investigation of contributions and limitations of conditioning processes to explaining how cues acquire erotic value and to attempt some integration between the sexual conditioning literature and research on sexual orientation or more generally sexual partner preference.

  6. Attraction to male facial masculinity in gay men in China: relationship to intercourse preference positions and sociosexual behavior.

    Science.gov (United States)

    Zheng, Lijun; Hart, Trevor A; Zheng, Yong

    2013-10-01

    Distinctions are commonly made regarding preferences for insertive or receptive anal intercourse within gay male communities. Three sexual self-labels are typically specified: "top," meaning a man who prefers the insertive role, "bottom," meaning a man who prefers the receptive role, and "versatile," meaning a man willing to perform either role. In this study, we examined the association between intercourse position preference and preference for male facial masculinity among 447 gay men across multiple cities in China. Each participant was shown 10 pairs of male faces sequentially, with each pair consisting of a masculinized and feminized version of the same base face. Tops preferred the feminized male face over the masculinized face, bottoms preferred the masculinized male face over the feminized face, and versatiles did not have a preference. Tops preferred more feminized male faces than did bottoms and versatiles. Preferences for male facial masculinity were also associated with sociosexual orientation and the nature of the associations differed by sex role preferences. Among tops, men who were less restricted preferred more feminine male faces compared to men who were more restricted. Among bottoms, men who were less restricted preferred more masculine male faces compared to men who were more restricted. Among versatiles, there was no association between sociosexual orientation and preferences for male facial masculinity. These findings provide new evidence that less sociosexually restricted men have stronger preferences for sexual dimorphism in the sexual partners they prefer than do more restricted men.

  7. Orientations of linear stone arrangements in New South Wales

    CERN Document Server

    Hamacher, Duane W; Norris, Ray P

    2012-01-01

    We test the hypothesis that Aboriginal linear stone arrangements in New South Wales (NSW) are oriented to cardinal directions. We accomplish this by measuring the azimuths of stone arrangements described in site cards from the NSW Aboriginal Heritage Information Management System. We then survey a subset of these sites to test the accuracy of information recorded on the site cards. We find a preference recorded in the site cards for cardinal orientations among azimuths. The field surveys show that the site cards are reasonably accurate, but the surveyors probably did not correct for magnetic declinations. Using Monte Carlo statistics, we show that these preferred orientations did not occur by chance and that Aboriginal people deliberately aligned these arrangements to the approximate cardinal directions. We briefly explore possible reasons for these preferred orientations and highlight the need for future work.

  8. Gender bias in specialty preferences among Danish medical students

    DEFF Research Database (Denmark)

    Pedersen, Laura Erna Toftegaard; Skytte, Nanna Hasle Bak; Dissing, Agnete Skovlund

    2011-01-01

    Female medical students tend to prefer person-oriented specialties characterized by close doctor-patient contact and aspects of care. Conversely, male medical students tend to seek towards specialties with elements of autonomy, technology and "action" . Furthermore, female doctors will outnumber ...

  9. Discovering Learning Preferences and Learning Differences in the Classroom.

    Science.gov (United States)

    Bargar, June R.; And Others

    Understanding learning differences and how they function in the classroom is important to both students and teachers. The learning preferences described in this handbook are based on the concepts of psychological type developed by Carl Jung. Jung identified three sets of psychological processes, the areas of attitude (orientation), perception, and…

  10. Symmetric Euler orientation representations for orientational averaging.

    Science.gov (United States)

    Mayerhöfer, Thomas G

    2005-09-01

    A new kind of orientation representation called symmetric Euler orientation representation (SEOR) is presented. It is based on a combination of the conventional Euler orientation representations (Euler angles) and Hamilton's quaternions. The properties of the SEORs concerning orientational averaging are explored and compared to those of averaging schemes that are based on conventional Euler orientation representations. To that aim, the reflectance of a hypothetical polycrystalline material with orthorhombic crystal symmetry was calculated. The calculation was carried out according to the average refractive index theory (ARIT [T.G. Mayerhöfer, Appl. Spectrosc. 56 (2002) 1194]). It is shown that the use of averaging schemes based on conventional Euler orientation representations leads to a dependence of the result from the specific Euler orientation representation that was utilized and from the initial position of the crystal. The latter problem can be overcome partly by the introduction of a weighing factor, but only for two-axes-type Euler orientation representations. In case of a numerical evaluation of the average, a residual difference remains also if a two-axes type Euler orientation representation is used despite of the utilization of a weighing factor. In contrast, this problem does not occur if a symmetric Euler orientation representation is used as a matter of principle, while the result of the averaging for both types of orientation representations converges with increasing number of orientations considered in the numerical evaluation. Additionally, the use of a weighing factor and/or non-equally spaced steps in the numerical evaluation of the average is not necessary. The symmetrical Euler orientation representations are therefore ideally suited for the use in orientational averaging procedures.

  11. Al-doped ZnO seed layer-dependent crystallographic control of ZnO nanorods by using electrochemical deposition

    Energy Technology Data Exchange (ETDEWEB)

    Son, Hyo-Soo; Choi, Nak-Jung [Department of Nano-Optical Engineering, Korea Polytechnic University, Siheung 429-793 (Korea, Republic of); Kim, Kyoung-Bo [Department of Metallurgical and Materials Engineering, Inha Technical College, Incheon 402-752 (Korea, Republic of); Kim, Moojin [Department of Renewable Energy, Jungwon University, Goesan-gun, Chungbuk 367-805 (Korea, Republic of); Lee, Sung-Nam, E-mail: snlee@kpu.ac.kr [Department of Nano-Optical Engineering, Korea Polytechnic University, Siheung 429-793 (Korea, Republic of)

    2016-10-15

    Highlights: • Polar and semipolar ZnO NRs were successfully achieved by hydrothermal synthesis. • Semipolar and polar ZnO NRs were grown on ZnO and AZO/m-sapphire, respectively. • Al % of AZO/m-sapphire enhanced the lateral growth rate of polar ZnO NRs. - Abstract: We investigated the effect of an Al-doped ZnO film on the crystallographic direction of ZnO nanorods (NRs) using electrochemical deposition. From high-solution X-ray diffraction measurements, the crystallographic plane of ZnO NRs grown on (1 0 0) ZnO/m-plane sapphire was (1 0 1). The surface grain size of the (100) Al-doped ZnO (AZO) film decreased with increasing Al content in the ZnO seed layer, implying that the Al dopant accelerated the three-dimensional (3D) growth of the AZO film. In addition, it was found that with increasing Al doping concentration of the AZO seed layer, the crystal orientation of the ZnO NRs grown on the AZO seed layer changed from [1 0 1] to [0 0 1]. With increasing Al content of the nonpolar (1 0 0) AZO seed layer, the small surface grains with a few crystallographic planes of the AZO film changed from semipolar (1 0 1) ZnO NRs to polar (0 0 1) ZnO NRs due to the increase of the vertical [0 0 1] growth rate of the ZnO NRs owing to excellent electrical properties.

  12. A log-likelihood-gain intensity target for crystallographic phasing that accounts for experimental error.

    Science.gov (United States)

    Read, Randy J; McCoy, Airlie J

    2016-03-01

    The crystallographic diffraction experiment measures Bragg intensities; crystallographic electron-density maps and other crystallographic calculations in phasing require structure-factor amplitudes. If data were measured with no errors, the structure-factor amplitudes would be trivially proportional to the square roots of the intensities. When the experimental errors are large, and especially when random errors yield negative net intensities, the conversion of intensities and their error estimates into amplitudes and associated error estimates becomes nontrivial. Although this problem has been addressed intermittently in the history of crystallographic phasing, current approaches to accounting for experimental errors in macromolecular crystallography have numerous significant defects. These have been addressed with the formulation of LLGI, a log-likelihood-gain function in terms of the Bragg intensities and their associated experimental error estimates. LLGI has the correct asymptotic behaviour for data with large experimental error, appropriately downweighting these reflections without introducing bias. LLGI abrogates the need for the conversion of intensity data to amplitudes, which is usually performed with the French and Wilson method [French & Wilson (1978), Acta Cryst. A35, 517-525], wherever likelihood target functions are required. It has general applicability for a wide variety of algorithms in macromolecular crystallography, including scaling, characterizing anisotropy and translational noncrystallographic symmetry, detecting outliers, experimental phasing, molecular replacement and refinement. Because it is impossible to reliably recover the original intensity data from amplitudes, it is suggested that crystallographers should always deposit the intensity data in the Protein Data Bank.

  13. The analysis of crystallographic symmetry types in finite groups

    Science.gov (United States)

    Sani, Atikah Mohd; Sarmin, Nor Haniza; Adam, Nooraishikin; Zamri, Siti Norziahidayu Amzee

    2014-06-01

    Undeniably, it is human nature to prefer objects which are considered beautiful. Most consider beautiful as perfection, hence they try to create objects which are perfectly balance in shape and patterns. This creates a whole different kind of art, the kind that requires an object to be symmetrical. This leads to the study of symmetrical objects and pattern. Even mathematicians and ethnomathematicians are very interested with the essence of symmetry. One of these studies were conducted on the Malay traditional triaxial weaving culture. The patterns derived from this technique are symmetrical and this allows for further research. In this paper, the 17 symmetry types in a plane, known as the wallpaper groups, are studied and discussed. The wallpaper groups will then be applied to the triaxial patterns of food cover in Malaysia.

  14. PREFERENCE, PRINCIPLE AND PRACTICE

    DEFF Research Database (Denmark)

    Skovsgaard, Morten; Bro, Peter

    2011-01-01

    journalists justify themselves and their work. This article introduces an analytical framework for understanding legitimacy in a journalistic context. A framework based on a review of material ranging from historical accounts to research articles, and book-length studies. The framework comprises three...... distinct, but interconnected categories*preference, principle, and practice. Through this framework, historical attempts to justify journalism and journalists are described and discussed in the light of the present challenges for the profession....

  15. PREFERENCE, PRINCIPLE AND PRACTICE

    DEFF Research Database (Denmark)

    Skovsgaard, Morten; Bro, Peter

    2011-01-01

    Legitimacy has become a central issue in journalism, since the understanding of what journalism is and who journalists are has been challenged by developments both within and outside the newsrooms. Nonetheless, little scholarly work has been conducted to aid conceptual clarification as to how jou...... distinct, but interconnected categories*preference, principle, and practice. Through this framework, historical attempts to justify journalism and journalists are described and discussed in the light of the present challenges for the profession....

  16. Crystallographic origin of perpendicular magnetic anisotropy in CoPt film: polarized x-ray absorption study

    Energy Technology Data Exchange (ETDEWEB)

    Pandey, K.K.M.; Chen, J.S.; Liu, T.; Sun, C.J.; Chow, G.M.; (NU Sinapore); (ORNL)

    2009-09-17

    Crystallographic structure, growth induced miscibility gap and strain in Ta/Co{sub 100-x}Pt{sub x} (0 {le} x {le} 43 at%)/Ru/Ta/glass films deposited at ambient temperature were investigated using polarized x-ray absorption spectroscopy to clarify the origin of observed perpendicular magnetic anisotropy (PMA) in Co{sub 72}Pt{sub 28} film. Extended x-ray absorption fine structure spectroscopy data at Co K-edge showed that Co has a similar local atomic environment and averaged interatomic distance in the in-plane and out-of-plane polarization geometries for Co{sub 72}Pt{sub 28}, ruling out the contribution of magneto-elastic anisotropy and growth induced structural anisotropy as the origin of PMA. A large PMA in Co{sub 72}Pt{sub 28} film was attributed to the preferred hexagonal close-packed stacking as observed using the x-ray absorption near-edge structure spectroscopy.

  17. Coaching preferences of athletes.

    Science.gov (United States)

    Terry, P C; Howe, B L

    1984-12-01

    The study examined the coaching preferences of 80 male and 80 female athletes, as measured by the Leadership Scale for Sports (Chelladurai and Saleh, 1978, 1980). In addition, it attempted to assess the applicability to sport of the Life-cycle and Path-goal theories of leadership. Comparisons between groups were made on the basis of sex, age, and type of sport. A MANOVA indicated that athletes in independent sports preferred more democratic behaviour (p less than .001) and less autocratic behaviour (p = .028) than athletes in interdependent sports. No differences in coaching preferences were found which could be attributed to the age or sex of the athlete, or the variability of the sports task. These results partially supported the Path-goal theory, but did not support the Life-cycle theory. Athletes of all groups tended to favour coaches who displayed training behaviour and rewarding behaviour "often", democratic behaviour and social support behaviour "occasionally", and autocratic behaviour "seldom". This consistency may be a useful finding for those organizations and institutions interested in preparing coaches.

  18. Perspectives on Preference Aggregation.

    Science.gov (United States)

    Regenwetter, Michel

    2009-07-01

    For centuries, the mathematical aggregation of preferences by groups, organizations, or society itself has received keen interdisciplinary attention. Extensive theoretical work in economics and political science throughout the second half of the 20th century has highlighted the idea that competing notions of rational social choice intrinsically contradict each other. This has led some researchers to consider coherent democratic decision making to be a mathematical impossibility. Recent empirical work in psychology qualifies that view. This nontechnical review sketches a quantitative research paradigm for the behavioral investigation of mathematical social choice rules on real ballots, experimental choices, or attitudinal survey data. The article poses a series of open questions. Some classical work sometimes makes assumptions about voter preferences that are descriptively invalid. Do such technical assumptions lead the theory astray? How can empirical work inform the formulation of meaningful theoretical primitives? Classical "impossibility results" leverage the fact that certain desirable mathematical properties logically cannot hold in all conceivable electorates. Do these properties nonetheless hold true in empirical distributions of preferences? Will future behavioral analyses continue to contradict the expectations of established theory? Under what conditions do competing consensus methods yield identical outcomes and why do they do so?

  19. Tuning of the magnetostrictive properties of cobalt ferrite by forced distribution of substituted divalent metal ions at different crystallographic sites

    Science.gov (United States)

    Anantharamaiah, P. N.; Joy, P. A.

    2017-03-01

    Comparative studies have been made to understand the role of different crystallographic site preferences of the substituted non-magnetic divalent metal ions in the magnetostrictive properties of cobalt ferrite, by substitution of Zn2+ and/or Mg2+ for Fe3+ in CoMgxFe2-xO4, CoZnxFe2-xO4, and CoMgx/2Znx/2Fe2-xO4 (0.0 ≤ x ≤ 0.2). Detailed Raman spectral and magnetic characterizations are made to extract the information on the tetrahedral/octahedral site preferences of Zn and Mg in the spinel lattice of cobalt ferrite. The structural, microstructural, magnetic, Raman spectral, and magnetostrictive parameters of the studied compositions show distinguishable variations for x < 0.1 and x ≥ 0.1. Co-substitution of a small amount of Mg and Zn for Fe in CoMgx/2Znx/2Fe2-xO4 (x < 0.1) showed relatively larger strain sensitivity, [dλ/dH]max (-2.6 × 10-9 mA-1 for x = 0.05), higher than that for the Mg-substituted samples (-2.05 × 10-9 mA-1 for x = 0.05) and comparable to that for the Zn-substituted samples (-2.47 × 10-9 mA-1 for x = 0.05), without much drop in the maximum value of magnetostriction, λmax (-189 ppm for x = 0.05) compared to that for the unsubstituted counterpart (-221 ppm). The results show that it is possible to obtain high strain sensitivity (at fields <50 kA/m), along with high magnetostriction strain at low magnetic fields (˜250 kA/m), by tuning the distribution of the substituted cations in the tetrahedral and octahedral sites of the cobalt ferrite lattice.

  20. Adaptive behavior of neighboring neurons during adaptation-induced plasticity of orientation tuning in V1

    Directory of Open Access Journals (Sweden)

    Shumikhina Svetlana

    2009-12-01

    Full Text Available Abstract Background Sensory neurons display transient changes of their response properties following prolonged exposure to an appropriate stimulus (adaptation. In adult cat primary visual cortex, orientation-selective neurons shift their preferred orientation after being adapted to a non-preferred orientation. The direction of those shifts, towards (attractive or away (repulsive from the adapter depends mostly on adaptation duration. How the adaptive behavior of a neuron is related to that of its neighbors remains unclear. Results Here we show that in most cases (75%, cells shift their preferred orientation in the same direction as their neighbors. We also found that cells shifting preferred orientation differently from their neighbors (25% display three interesting properties: (i larger variance of absolute shift amplitude, (ii wider tuning bandwidth and (iii larger range of preferred orientations among the cluster of cells. Several response properties of V1 neurons depend on their location within the cortical orientation map. Our results suggest that recording sites with both attractive and repulsive shifts following adaptation may be located in close proximity to iso-orientation domain boundaries or pinwheel centers. Indeed, those regions have a more diverse orientation distribution of local inputs that could account for the three properties above. On the other hand, sites with all cells shifting their preferred orientation in the same direction could be located within iso-orientation domains. Conclusions Our results suggest that the direction and amplitude of orientation preference shifts in V1 depend on location within the orientation map. This anisotropy of adaptation-induced plasticity, comparable to that of the visual cortex itself, could have important implications for our understanding of visual adaptation at the psychophysical level.

  1. Thinking in Orienteering.

    Science.gov (United States)

    Johansen, Bjorn Tore

    1997-01-01

    A think-aloud technique, in which 20 orienteers verbalized their exact thoughts during orienteering, was used to examine the phenomenon of cognition during orienteering. Results indicate that orienteering is experienced as a task to be accomplished, a physical movement, and a dynamic process, and that thinking involves attuning perceptions to…

  2. Regulatory mode preferences for autonomy supporting versus controlling instructional styles.

    Science.gov (United States)

    Pierro, Antonio; Presaghi, Fabio; Higgins, Tory E; Kruglanski, Arie W

    2009-12-01

    Three studies carried out in educational settings examined determinants of teacher's instructional styles and students' degree of satisfaction with the learning climates created by such styles. Based upon regulatory mode theory, Studies 1 and 2 tested the hypotheses that teachers' locomotion orientation will be positively related, and their assessment orientation will be negatively related, to autonomy supportive (vs. controlling) instructional styles. Study 3 tested the hypothesis that students' regulatory mode will exhibit a fit effect with the prevalent learning climate in their school. Participants for Study 1 were 378 teachers (278 females); for Study 2 were 96 teachers (65 females); and for Study 3 were 190 students (all males). Participants completed questionnaires that included measures of teaching styles (Studies 1 and 2), perceived learning climate and satisfaction (Study 3), and regulatory mode orientations (Studies 1 and 3). In Study 2 regulatory mode orientations were experimentally induced. Results confirmed that teachers' autonomy supportive versus controlling styles were positively related to their locomotion orientations and negatively related to their assessment orientation, and that students with a stronger locomotion (vs. assessment) orientation reported a higher level of satisfaction when the learning climate was perceived as autonomy supportive (vs. controlling). The present studies show that teachers' preference for adopting an instructional style is influenced by their regulatory mode orientations, and that the effects of a learning climate on students' satisfaction are contingent on a fit between type of learning climate and students' regulatory mode orientations.

  3. Advanced yield strength of interconnector ribbon for photovoltaic module using crystallographic texture control

    Science.gov (United States)

    Kang, Byungjun; Park, Nochang; Tark, Sung Ju; Oh, Won Wook; Park, Sungeun; Kim, Young Do; Lee, Hae-Seok; Kim, Donghwan

    2014-03-01

    This paper reports a study on reducing the yield strength of Cu ribbon wire used for Si solar cell interconnections in solar panels. Low yield strength Cu core should be used as the interconnector ribbon to minimize the fracture of Si solar cells during the tabbing process. We lowered the yield strength of Cu ribbon by controlling the crystallographic texture without increasing the annealing time and temperature. The crystallographic texture was controlled by lubrication in a cold rolling process. The crystallographic texture was observed by scanning electron microscopy with electron back scattered diffraction. A tensile test was performed for the comparison of the mechanical properties of Cu with and without lubrication. The average yield strength was 91.2 MPa with lubrication whereas the yield strength was 99.6 MPa without lubrication. The lower value of the lubricated samples seemed to be caused by the higher cube texture intensity than that of the samples without lubrication.

  4. Crystallographically driven magnetic behaviour of arrays of monocrystalline Co nanowires

    KAUST Repository

    Ivanov, Yu P.

    2014-11-07

    Cobalt nanowires, 40 nm in diameter and several micrometers long, have been grown by controlled electrodeposition into ordered anodic alumina templates. The hcp crystal symmetry is tuned by a suitable choice of the electrolyte pH (between 3.5 and 6.0) during growth. Systematic high resolution transmission electron microscopy imaging and analysis of the electron diffraction patterns reveals a dependence of crystal orientation from electrolyte pH. The tailored modification of the crystalline signature results in the reorientation of the magnetocrystalline anisotropy and increasing experimental coercivity and squareness with decreasing polar angle of the \\'c\\' growth axis. Micromagnetic modeling of the demagnetization process and its angular dependence is in agreement with the experiment and allows us to establish the change in the character of the magnetization reversal: from quasi-curling to vortex domain wall propagation modes when the crystal \\'c\\' axis tilts more than 75° in respect to the nanowire axis.

  5. Identification and possible space orientation of 'light-sensitive' defects in Ge

    Energy Technology Data Exchange (ETDEWEB)

    Gerasimov, A.B.; Dolidze, N.D.; Donina, R.M.; Konovalenko, B.M.; Ofengeim, G.L.; Tsertsvadze, A.A. (AN Gruzinskoj SSR, Tbilisi. Inst. Fiziki)

    1982-03-16

    A radiation defect responsible for the 0.52 eV absorption band in the IR absorption spectrum of irradiated Ge is investigated. n-type samples cut in three main crystallographic directions <111>, <110>, and <100> are irradiated by 3 to 5 MeV electrons at T approximately 77 K. During the measurements monochromatic polarized light and uniaxial stress are used. It is shown that the radiation defect studied has the property of dichroism. Besides, depending on the direction of applied uniaxial stress, variations in the value of the 0.52 eV absorption band are revealed. The space orientation of the radiation defect giving rise to the 0.52 eV absorption band is determined. Based on the analysis of the data obtained as well as on the analogy with silicon, it is assumed that the defect is a divacancy whose axis is oriented close to the <110> crystallographic directions.

  6. Effect of crystallographic orientation in textured Ba0.92Ca0.08TiO3 piezoelectric ceramics

    Science.gov (United States)

    Haugen, Astri Bjørnetun; Morozov, Maxim I.; Johnsson, Mats; Grande, Tor; Einarsrud, Mari-Ann

    2014-10-01

    Strongly textured lead-free Ba0.92Ca0.08TiO3 piezoelectric ceramics were fabricated by tape casting and templated grain growth. Dense ceramics with both favorable ⟨100⟩ and unfavorable ⟨111⟩ texture were successfully prepared. Enhanced piezoelectric performance was demonstrated for ceramics with ⟨100⟩ texture, in line with the predictions based on reported piezoelectric coefficients of tetragonal BaTiO3. Due to the expanded tetragonal range through Ca-substitution, ⟨100⟩ texture is favorable over a wide temperature range. The ⟨100⟩ texture also results in the enhanced piezoelectric performance being temperature-independent. In addition to engineering of stable, high-performance lead-free piezoelectric ceramics, this study has demonstrated that consideration of the extender/rotator nature of piezoelectric properties is imperative for improving the piezoelectric response through texturing.

  7. Puerto Rico Revealed Preference data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Revealed preference models provide insights into recreational angler behavior and the economic value of recreational fishing trips. Revealed preference data is...

  8. Senior High School Students' Preference and Reasoning Modes about Nuclear Energy Use.

    Science.gov (United States)

    Yang, Fang-Ying; Anderson, O. Roger

    2003-01-01

    Examines senior high school students' cognitive orientation toward scientific or social information, designated as information preference, and associated preferential reasoning modes when presented with an environmental issue concerning nuclear energy usage. Investigates the association of information preference variable with academic and personal…

  9. Senior High School Students' Preference and Reasoning Modes about Nuclear Energy Use.

    Science.gov (United States)

    Yang, Fang-Ying; Anderson, O. Roger

    2003-01-01

    Examines senior high school students' cognitive orientation toward scientific or social information, designated as information preference, and associated preferential reasoning modes when presented with an environmental issue concerning nuclear energy usage. Investigates the association of information preference variable with academic and personal…

  10. Humanistic Worldmindedness and Peace Proposal Preferences in Pacifist, ROTC, and Random Student Samples.

    Science.gov (United States)

    Simmons, Dale D.; And Others

    Assuming that pacifist and ROTC allegiances are associated with differing basic orientations toward mankind and differing preferences for resolution of international conflict, the Worldmindedness Scale and the peace proposal preference procedures (developed by cooperating participants in the international survey "Images of the Year 2000") were…

  11. Elasto-Plastic Behavior of High RRR Niobium: Effects of Crystallographic Texture, Microstructure and Hydrogen Concentration

    Energy Technology Data Exchange (ETDEWEB)

    G.R. Myneni; S.R. Agnew

    2002-11-01

    Conventional assessments of the mechanical properties of polycrystalline high RRR niobium via tensile testing have revealed unusually low apparent Young's moduli and yield strength in annealed samples. These observations motivated the current investigation of a variety of possible contributors: crystallographic texture, grain size, and impurity concentration. It is shown that the crystallographic textures of a single lot of niobium are essentially unchanged by post-recrystallization anneals at temperatures up to 800 C. Ultrasonic measurements reveal that the elastic response is not degraded by annealing. Rather, the material's extremely low yield point gives the impression of a low elastic modulus during tensile testing.

  12. Crystallographic Identification of Lipid as an Integral Component of the Epitope of HIV Broadly Neutralizing Antibody 4E10.

    Science.gov (United States)

    Irimia, Adriana; Sarkar, Anita; Stanfield, Robyn L; Wilson, Ian A

    2016-01-19

    Numerous studies of the anti-HIV-1 envelope glycoprotein 41 (gp41) broadly neutralizing antibody 4E10 suggest that 4E10 also interacts with membrane lipids, but the antibody regions contacting lipids and its orientation with respect to the viral membrane are unknown. Vaccine immunogens capable of re-eliciting these membrane proximal external region (MPER)-like antibodies may require a lipid component to be successful. We performed a systematic crystallographic study of lipid binding to 4E10 to identify lipids bound by the antibody and the lipid-interacting regions. We identified phosphatidic acid, phosphatidylglycerol, and glycerol phosphate as specific ligands for 4E10 in the crystal structures. 4E10 used its CDRH1 loop to bind the lipid head groups, while its CDRH3 interacted with the hydrophobic lipid tails. Identification of the lipid binding sites on 4E10 may aid design of immunogens for vaccines that include a lipid component in addition to the MPER on gp41 for generation of broadly neutralizing antibodies.

  13. Enzyme transient state kinetics in crystal and solution from the perspective of a time-resolved crystallographer.

    Science.gov (United States)

    Schmidt, Marius; Saldin, Dilano K

    2014-03-01

    With recent technological advances at synchrotrons [Graber et al., J. Synchrotron Radiat. 18, 658-670 (2011)], it is feasible to rapidly collect time-resolved crystallographic data at multiple temperature settings [Schmidt et al., Acta Crystallogr. D 69, 2534-2542 (2013)], from which barriers of activation can be extracted. With the advent of fourth generation X-ray sources, new opportunities emerge to investigate structure and dynamics of biological macromolecules in real time [M. Schmidt, Adv. Condens. Matter Phys. 2013, 1-10] in crystals and potentially from single molecules in random orientation in solution [Poon et al., Adv. Condens. Matter Phys. 2013, 750371]. Kinetic data from time-resolved experiments on short time-scales must be interpreted in terms of chemical kinetics [Steinfeld et al., Chemical Kinetics and Dynamics, 2nd ed. (Prentience Hall, 1985)] and tied to existing time-resolved experiments on longer time-scales [Schmidt et al., Acta Crystallogr. D 69, 2534-2542 (2013); Jung et al., Nat. Chem. 5, 212-220 (2013)]. With this article, we will review and outline steps that are required to routinely determine the energetics of reactions in biomolecules in crystal and solution with newest X-ray sources. In eight sections, we aim to describe concepts and experimental details that may help to inspire new approaches to collect and interpret these data.

  14. Analysis of the structural continuity in twinned crystals in terms of pseudo-eigensymmetry of crystallographic orbits

    Directory of Open Access Journals (Sweden)

    Mohamed Amine Marzouki

    2014-01-01

    Full Text Available The reticular theory of twinning gives the necessary conditions on the lattice level for the formation of twins. The latter are based on the continuation, more or less approximate, of a substructure through the composition surface. The analysis of this structural continuity can be performed in terms of the eigensymmetry of the crystallographic orbits corresponding to occupied Wyckoff positions in the structure. If {\\cal G} is the space group of the individual and {\\cal H} a space group which fixes the twin lattice obtained as an intersection of the space groups of the individuals in their respective orientations, then a structural continuity is obtained if (1 the eigensymmetry of an orbit under {\\cal G} contains the twin operation; (2 the eigensymmetry of a union of orbits under {\\cal G} contains the twin operation; (3 the eigensymmetry of a split orbit under {\\cal H} contains the twin operation; or (4 the eigensymmetry of a union of split orbits under {\\cal H} contains the twin operation. The case of the twins in melilite is analysed: the (approximate restoration of some of the orbits explains the formation of these twins.

  15. Enzyme transient state kinetics in crystal and solution from the perspective of a time-resolved crystallographer

    Directory of Open Access Journals (Sweden)

    Marius Schmidt

    2014-03-01

    Full Text Available With recent technological advances at synchrotrons [Graber et al., J. Synchrotron Radiat. 18, 658–670 (2011], it is feasible to rapidly collect time-resolved crystallographic data at multiple temperature settings [Schmidt et al., Acta Crystallogr. D 69, 2534–2542 (2013], from which barriers of activation can be extracted. With the advent of fourth generation X-ray sources, new opportunities emerge to investigate structure and dynamics of biological macromolecules in real time [M. Schmidt, Adv. Condens. Matter Phys. 2013, 1–10] in crystals and potentially from single molecules in random orientation in solution [Poon et al., Adv. Condens. Matter Phys. 2013, 750371]. Kinetic data from time-resolved experiments on short time-scales must be interpreted in terms of chemical kinetics [Steinfeld et al., Chemical Kinetics and Dynamics, 2nd ed. (Prentience Hall, 1985] and tied to existing time-resolved experiments on longer time-scales [Schmidt et al., Acta Crystallogr. D 69, 2534–2542 (2013; Jung et al., Nat. Chem. 5, 212–220 (2013]. With this article, we will review and outline steps that are required to routinely determine the energetics of reactions in biomolecules in crystal and solution with newest X-ray sources. In eight sections, we aim to describe concepts and experimental details that may help to inspire new approaches to collect and interpret these data.

  16. Vibrational algorithms for quantitative crystallographic analyses of hydroxyapatite-based biomaterials: II, application to decayed human teeth.

    Science.gov (United States)

    Adachi, Tetsuya; Pezzotti, Giuseppe; Yamamoto, Toshiro; Ichioka, Hiroaki; Boffelli, Marco; Zhu, Wenliang; Kanamura, Narisato

    2015-05-01

    A systematic investigation, based on highly spectrally resolved Raman spectroscopy, was undertaken to research the efficacy of vibrational assessments in locating chemical and crystallographic fingerprints for the characterization of dental caries and the early detection of non-cavitated carious lesions. Raman results published by other authors have indicated possible approaches for this method. However, they conspicuously lacked physical insight at the molecular scale and, thus, the rigor necessary to prove the efficacy of this spectroscopy method. After solving basic physical challenges in a companion paper, we apply them here in the form of newly developed Raman algorithms for practical dental research. Relevant differences in mineral crystallite (average) orientation and texture distribution were revealed for diseased enamel at different stages compared with healthy mineralized enamel. Clear spectroscopy features could be directly translated in terms of a rigorous and quantitative classification of crystallography and chemical characteristics of diseased enamel structures. The Raman procedure enabled us to trace back otherwise invisible characteristics in early caries, in the translucent zone (i.e., the advancing front of the disease) and in the body of lesion of cavitated caries.

  17. Human preference for air movement

    DEFF Research Database (Denmark)

    Toftum, Jørn; Melikov, Arsen Krikor; Tynel, A.

    2002-01-01

    Human preference for air movement was studied at slightly cool, neutral, and slightly warm overall thermal sensations and at temperatures ranging from 18 deg.C to 28 deg.C. Air movement preference depended on both thermal sensation and temperature, but large inter-individual differences existed...... between subjects. Preference for less air movement was linearly correlated with draught discomfort, but the percentage of subjects who felt draught was lower than the percentage who preferred less air movement....

  18. Correlated Preferences for Male Facial Masculinity and Partner Traits in Gay and Bisexual Men in China.

    Science.gov (United States)

    Zheng, Lijun; Zheng, Yong

    2015-07-01

    Previous studies have documented the correlation between preferences for male facial masculinity and perceived masculinity: women who rate their male partner as more masculine tend to prefer more masculine faces. Men's self-rated masculinity predicts their female partner's preference for masculinity. This study examined the association between other trait preferences and preference for male facial masculinity among 556 gay and bisexual men across multiple cities in China. Participants were asked to choose the three most important traits in a romantic partner from a list of 23 traits. Each participant was then asked to choose a preferred face in each of 10 pairs of male faces presented sequentially, with each pair consisting of a masculinized and feminized version of the same base face. The results indicated that preferences for health and status-related traits were correlated with preferences for male facial masculinity in gay and bisexual men in China; individuals who were more health- or status-oriented in their preferences for a romantic partner preferred more masculine male faces than individuals with lower levels of these orientations. The findings have implications for the correlated preferences for facial masculinity and health- and status-related traits and may be related to perceived health and dominance/aggression of masculine faces based on a sample of non-Western gay and bisexual men.

  19. Homosexual mating preferences from an evolutionary perspective: sexual selection theory revisited.

    Science.gov (United States)

    Gobrogge, Kyle L; Perkins, Patrick S; Baker, Jessica H; Balcer, Kristen D; Breedlove, S Marc; Klump, Kelly L

    2007-10-01

    Studies in evolutionary psychology and sexual selection theory show that heterosexual men prefer younger mating partners than heterosexual women in order to ensure reproductive success. However, previous research has generally not examined differences in mating preferences as a function of sexual orientation or the type of relationship sought in naturalistic settings. Given that homosexual men seek partners for reasons other than procreation, they may exhibit different mating preferences than their heterosexual counterparts. Moreover, mating preferences may show important differences depending on whether an individual is seeking a long-term versus a short-term relationship. The purpose of the present study was to examine these issues by comparing partner preferences in terms of age and relationship type between homosexual and heterosexual men placing internet personal advertisements. Participants included 439 homosexual and 365 heterosexual men who placed internet ads in the U.S. or Canada. Ads were coded for the participant's age, relationship type (longer-term or short-term sexual encounter) sought, and partner age preferences. Significantly more homosexual than heterosexual men sought sexual encounters, although men (regardless of sexual orientation) seeking sexual encounters preferred a significantly wider age range of partners than men seeking longer-term relationships. These findings suggest that partner preferences are independent of evolutionary drives to procreate, since both types of men preferred similar ages in their partners. In addition, they highlight the importance of examining relationship type in evolutionary studies of mating preferences, as men's partner preferences show important differences depending upon the type of relationship sought.

  20. Immigrants' location preferences

    DEFF Research Database (Denmark)

    Damm, Anna Piil

    This paper exploits a spatial dispersal policy for refugee immigrants to estimate the importance of local and regional factors for refugees' location preferences. The main results of a mixed proportional hazard competing risks model are that placed refugees react to high regional unemployment...... and lack of a local immigrant population by migrating to large municipalities. Lack of local fellow countrymen, however, increases the exit rate to medium-sized as well as large municipalities. This finding is likely to be a result of the dispersal policy. Finally, refugees react strongly to assignment...

  1. Understanding political market orientation

    DEFF Research Database (Denmark)

    Ormrod, Robert P.; Henneberg, Stephan C.

    This article develops a conceptual framework and measurement model of political market orientation that consists of attitudinal and behavioural constructs. The article reports on perceived relationships among different behavioral aspects of political market orientation and the attitudinal influen......, a more surprising result is the inconclusive effect of a voter orientation on market-oriented behaviours. The article discusses the findings in the context of the existing literature in political marketing and commercial market orientation.......This article develops a conceptual framework and measurement model of political market orientation that consists of attitudinal and behavioural constructs. The article reports on perceived relationships among different behavioral aspects of political market orientation and the attitudinal...... influences of such behavior. The study includes structural equation modeling to investigate several propositions. While the results show that political parties need to focus on several different aspects of market-oriented behavior, especially using an internal and external orientation as cultural antecedents...

  2. Chemical profiles along olivine crystallographic axes: a record of the melt-rock interaction sequence forming Hole U1309D Olivine-rich troctolites (Atlantis Massif, MAR, 30°N)

    Science.gov (United States)

    Ferrando, Carlotta; Godard, Marguerite; Ildefonse, Benoit; Rampone, Elisabetta

    2017-04-01

    The gabbroic section drilled at IODP Hole U1309D (Mid-Atlantic Ridge, IODP Expeditions 304, 305) comprises a whole range of modes from primitive olivine-rich troctolites to evolved gabbros. These series occur as discrete alternating intervals of variable composition and thickness at different depths. High MgO contents and a relatively large proportion of olivine-rich lithologies (up to 90% modal olivine) characterize this gabbroic section. Contacts between olivine-rich troctolites and neighboring coarse grained olivine gabbros are sharp, with the exception of the contacts between olivine-rich intervals and cross-cutting gabbroic veins, which are diffuse and characterized by progressive variations in plagioclase content. Olivine-rich troctolites are heterogeneously distributed along the borehole and show variable modal composition: centimeter to decimeter scale dunitic (90% olivine), troctolitic (enriched in plagioclase) and wehrlitic (enriched in clinopyroxene) domains were identified. Previous in-situ trace element geochemistry and crystallographic preferred orientation measurements of olivine-rich troctolites indicated that they record extensive melt impregnation of pre-existing olivine-rich material, either mantle rocks or dunitic cumulate. We performed a detailed multi-scale petro-structural and geochemical study on selected samples of well-preserved olivine-rich troctolites with the aim to unravel the sequence of re-equilibration processes and better constrain the local conditions driving the formation of these rocks. Processed EBSD maps show variable textures at single sample scale. All identified domains are characterized by coarse grained and deformed olivines, and small rounded undeformed olivines. Coarse grained and small rounded olivines have the same major and trace element compositions. Small olivines are interpreted as relicts after dissolution of coarse grained olivines. Clinopyroxene, plagioclase, and minor orthopyroxene are present as interstitial

  3. A Rate-Dependent Crystal Plasticity Analysis of Orientation Stability in Biaxial Tension of Magnesium

    Institute of Scientific and Technical Information of China (English)

    Donghong Zhang; Saiyi Li

    2011-01-01

    The development of texture during plastic deformation plays an important role in determining the stretch formability of magnesium alloy sheets. In this study, the orientation stability during equibiaxial tension of magnesium was analyzed based on three dimensional lattice rotations calculated by using a rate-dependent crystal plasticity model and assuming five different combinations of slip modes. The results show that no orientations can satisfy the stability criteria with both zero rotation velocity and convergent orientation flow in all dimensions. However, relatively stable orientations with zero rotation velocity and an overall convergence are found. They are featured by characteristic alignments of specific crystallographic directions in the macroscopic axis of contraction, depending on the slip modes involved in the deformation. It is also shown that the orientation stability varies significantly with the deviation of deformation mode from equibiaxial tension. The simulation results are briefly discussed in comparison with pre-existing experiments.

  4. Microstructure and Crystallographic Texture Variations in the Friction-Stir-Welded Al-Al2O3-B4C Metal Matrix Composite Produced by Accumulative Roll Bonding

    Science.gov (United States)

    Mohammadnezhad, Mahyar; Shamanian, Morteza; Zabolian, Azam; Taheri, Mahshid; Javaheri, Vahid; Navidpour, Amir Hossein; Nezakat, Majid; Szpunar, Jerzy A.

    2015-12-01

    In this research, ultrafine-grained sheets of aluminum matrix composite (Al-Al2O3-B4C) were produced by accumulative roll bonding ARB technique. As-received, ultrafine-grained aluminum composite sheets were joined by friction-stir welding. The microstructure, crystallographic texture, and Vickers hardness in the weld zones were investigated. Electron backscattered diffraction results revealed occurrence of dynamic recrystallization and demonstrated existence of different grain orientations within the weld nugget. Produced composite plates illustrated rotated cubic texture. Moreover, in the nugget, a well-recrystallized grain structure having characteristic strong shear texture component finally developed. However, the texture result in the heat-affected zone illustrated rotated cubic and Goss components that related to the effect of heat input. Friction-stir welding refined the grain size in the weld zone. The hardness also improved with the peak hardness being observed towards the advancing stir welding side.

  5. Crystallographic features of {alpha}``-martensite in titanium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Ivasishin, O.M. [AN Ukrainskoj SSR, Kiev (Ukraine). Inst. Metallov Fiziki; Kosenko, N.S. [AN Ukrainskoj SSR, Kiev (Ukraine). Inst. Metallov Fiziki; Shevchenko, S.V. [AN Ukrainskoj SSR, Kiev (Ukraine). Inst. Metallov Fiziki

    1995-12-01

    Equilibrium volume fractions of twins ({alpha}{sub 0}) and habit plane orientation (anti n{sub 0}) of the orthorhombic {alpha}``-martensite in titanium alloys with {beta}-stabilizing elements were determined by minimization of the elastic strain energy. Calculations were made in the basis of one of the twinned domains. It was shown that these parameters are varying considerably depending on the solute element content. For Ti-Ta and Ti-Mo systems habit plane rotated from {l_brace}434{r_brace}{sub {beta}} to {l_brace}433{r_brace}{sub {beta}} pole and {alpha}{sub 0} grew with Ta (Mo) content increase. For Ti-20at%Ta {alpha}{sub 0} reached the value of 1, i.e. martensite plate became monodomain. For Ti-Mo system monodomain state was not achieved. For Ti-Nb system converse concentrational dependence of martensite parameters was obtained: {alpha}{sub 0} decreased with Nb content increase, and n showed a rotation from {l_brace}434{r_brace}{sub {beta}} pole in a direction opposite to that for Ti-Ta and Ti-Mo systems. (orig.).

  6. Entrepreneurial orientation, market orientation, and competitive environment

    DEFF Research Database (Denmark)

    Sørensen, Hans Eibe; Cadogan, John W.

    orientation, and competitive environment shape business performance via a three-way interaction. We test the model using primary data from the CEOs of 270 CEO of manufacturing firms, together with secondary data on these firms' profit performance. An assessment of the results indicates that customer......This study sheds light on the role that the competitive environment plays in determining how elements of market orientation and elements of entrepreneurial orientation interact to influence business success. We develop a model in which we postulate that market orientation, entrepreneurial...... orientations. Also, these moderating effects are stronger for firms operating in highly competitive environments. For the innovativeness component of entrepreneurship, however, the positive relationship between innovativeness and ROA decreases as the competitive environment becomes more hostile....

  7. Object oriented methods

    CERN Document Server

    Graham, Ian

    1994-01-01

    This book is a revision of Ian Graham's successful survey of the whole area of object technology. It covers object- oriented programming, object-oriented design, object- oriented analysis, object-oriented databases and treats several related technologies. New to this edition are more applications of object-oriented methods and more coverage of object-oriented database products available. Graham has also doubled the design and analysis material that examines over 60 different approaches - making this the most comprehensive book on the market. Also new is the foreword by Grady Booch.

  8. Negative Average Preference Utilitarianism

    Directory of Open Access Journals (Sweden)

    Roger Chao

    2012-03-01

    Full Text Available For many philosophers working in the area of Population Ethics, it seems that either they have to confront the Repugnant Conclusion (where they are forced to the conclusion of creating massive amounts of lives barely worth living, or they have to confront the Non-Identity Problem (where no one is seemingly harmed as their existence is dependent on the “harmful” event that took place. To them it seems there is no escape, they either have to face one problem or the other. However, there is a way around this, allowing us to escape the Repugnant Conclusion, by using what I will call Negative Average Preference Utilitarianism (NAPU – which though similar to anti-frustrationism, has some important differences in practice. Current “positive” forms of utilitarianism have struggled to deal with the Repugnant Conclusion, as their theory actually entails this conclusion; however, it seems that a form of Negative Average Preference Utilitarianism (NAPU easily escapes this dilemma (it never even arises within it.

  9. Why Languages Prefer Prohibitives

    Institute of Scientific and Technical Information of China (English)

    Johan van der Auwera

    2006-01-01

    This paper deals with prohibitive markers, i.e., negative markers that are more or less dedicated to the expression of a prohibition. It documents the variety in the formal make-up of these markers and it confims the earlier claims that they are frequent everywhere, with at least one exception, viz., Western Europe. Four origins are discussed:prohibitive markers may derive from predicative constructions, they may appear as a side product of Jespersen's cycle,they may derive from a univerbation of imperative and negative markers, and they may be borrowed. As explanation is offered as to why languages prefer to have prohibitive markers. It is argued that attempts to explain this preference in terms of morphosyntax are misguided. Instead a frequency-based semantic explanation is offered. The most frequent use of negatives are declarative, thereby inviting a static ‘it is not the case that' paraphrase. It is important, however, to mark clearly that prohibitives are instances of a dynamic ‘let it be the case that' appeal. The paper ends on a discussion of languages that do not employ prohibitive markers.

  10. Interpretation of quantitative crystallographic texture in copper electrodeposits on amorphous substrates

    DEFF Research Database (Denmark)

    Pantleon, Karen; Jensen, Jens Arne Dahl; Somers, Marcel A. J.

    2004-01-01

    Crystallographic texture and morphology in Cu electrodeposits was studied in relation to the current density and the content of the organic levelling additive 3-mercapto-1-propanesulfonate. The substrate onto which Cu was electrodeposited consisted of amorphous Ni-P in order to allow substrate...

  11. Crystallographic structural organization of human rhinovirus serotype 16, 14, 3, 2 and 1A

    Science.gov (United States)

    Janner, A.

    2006-07-01

    The capsid of the icosahedral virion is encapsulated between two polyhedra scaled according to the golden mean, each being composed of an icosahedron and a dodecahedron. Structural units of the coat proteins are enclosed into forms whose projections along the icosahedral symmetry axes obey the crystallographic law of rational indices.

  12. Evaluating preschool children's preferences for motivational systems during instruction.

    Science.gov (United States)

    Heal, Nicole A; Hanley, Gregory P

    2007-01-01

    Preschool teachers rely on several strategies for motivating children to participate in learning activities. In the current study, we evaluated the effectiveness of and preference for three teaching contexts in which embedded, sequential, or no programmed reinforcement was arranged. The embedded context included highly preferred teaching materials, the sequential context included highly preferred edible items for correct responding, and a control context included neither. In addition, an exclusively play-oriented activity was included as a fourth option to determine if one of the direct teaching contexts could compete with a relatively unstructured and exclusively child-led activity. All participants preferred the sequential context (use of high-quality consequences) over the embedded context (use of high-quality teaching materials), 2 of the 4 participants preferred some motivational system to none at all, and the play area was selected over all variants of the instructional contexts during the majority of trials. We found either no or small differences in correct responding in the different instructional contexts; however, rates of undesirable behavior were highest in the least preferred interaction area for 3 of the 4 participants. Implications for the design of effective and preferred teaching environments for young children are discussed.

  13. They Call it Orienteering

    Science.gov (United States)

    Wexler, Mark

    1977-01-01

    Through the use of personal anecdotes, the author details his initial experience with orienteering, a sport rapidly increasing in popularity that teaches people not to get lost in the woods. Sources of information about orienteering are provided. (BT)

  14. Theories of Sexual Orientation.

    Science.gov (United States)

    Storms, Michael D.

    1980-01-01

    Results indicated homosexuals, heterosexuals, and bisexuals did not differ within each sex on measures of masculinity and femininity. Strong support was obtained for the hypothesis that sexual orientation relates primarily to erotic fantasy orientation. (Author/DB)

  15. Conductive layer for biaxially oriented semiconductor film growth

    Science.gov (United States)

    Findikoglu, Alp T.; Matias, Vladimir

    2007-10-30

    A conductive layer for biaxially oriented semiconductor film growth and a thin film semiconductor structure such as, for example, a photodetector, a photovoltaic cell, or a light emitting diode (LED) that includes a crystallographically oriented semiconducting film disposed on the conductive layer. The thin film semiconductor structure includes: a substrate; a first electrode deposited on the substrate; and a semiconducting layer epitaxially deposited on the first electrode. The first electrode includes a template layer deposited on the substrate and a buffer layer epitaxially deposited on the template layer. The template layer includes a first metal nitride that is electrically conductive and has a rock salt crystal structure, and the buffer layer includes a second metal nitride that is electrically conductive. The semiconducting layer is epitaxially deposited on the buffer layer. A method of making such a thin film semiconductor structure is also described.

  16. Entrepreneurial orientation, market orientation, and competitive environment

    DEFF Research Database (Denmark)

    Sørensen, Hans Eibe; Cadogan, John W.

    orientation, and competitive environment shape business performance via a three-way interaction. We test the model using primary data from the CEOs of 270 CEO of manufacturing firms, together with secondary data on these firms' profit performance. An assessment of the results indicates that customer...... orientation moderates the positive relationships between the competitiveness element of entrepreneurial orientation and market share and return on assets (ROA): the positive relationships between competitiveness and market share and competitiveness and ROA become stronger the greater the firms' customer...

  17. How shared preferences in music create bonds between people: values as the missing link.

    Science.gov (United States)

    Boer, Diana; Fischer, Ronald; Strack, Micha; Bond, Michael H; Lo, Eva; Lam, Jason

    2011-09-01

    How can shared music preferences create social bonds between people? A process model is developed in which music preferences as value-expressive attitudes create social bonds via conveyed value similarity. The musical bonding model links two research streams: (a) music preferences as indicators of similarity in value orientations and (b) similarity in value orientations leading to social attraction. Two laboratory experiments and one dyadic field study demonstrated that music can create interpersonal bonds between young people because music preferences can be cues for similar or dissimilar value orientations, with similarity in values then contributing to social attraction. One study tested and ruled out an alternative explanation (via personality similarity), illuminating the differential impact of perceived value similarity versus personality similarity on social attraction. Value similarity is the missing link in explaining the musical bonding phenomenon, which seems to hold for Western and non-Western samples and in experimental and natural settings.

  18. Tensorial Orientation Scores

    NARCIS (Netherlands)

    van de Gronde, Jasper J.; Azzopardi, George; Petkov, Nicolai

    2015-01-01

    Orientation scores are representations of images built using filters that only select on orientation (and not on the magnitude of the frequency). Importantly, they allow (easy) reconstruction, making them ideal for use in a filtering pipeline. Traditionally a specific set of orientations has to be c

  19. Research on the orientation distribution of fibers immersed in a pipe flow

    Institute of Scientific and Technical Information of China (English)

    林建忠; 张卫峰; 王叶龙

    2002-01-01

    The computed orientation distribution of fibers immersed in laminar pipe flows showed that the longitudinal distributions are wide for small Reynolds numbers and become narrower with increasing Re. For low Re number, the axial orientation distributions are broad with almost no preferred orientations. For high Re number, the axial distribution becomes narrow, with sharp maxima. The mean values of the longitudinal orientation depend strongly on the Re number. The computed results are in qualitative agreement with relevant experimental results.

  20. Fatal attraction: the effects of mortality salience on evaluations of charismatic, task-oriented, and relationship-oriented leaders.

    Science.gov (United States)

    Cohen, Florette; Solomon, Sheldon; Maxfield, Molly; Pyszczynski, Tom; Greenberg, Jeff

    2004-12-01

    A study was conducted to assess the effects of mortality salience on evaluations of political candidates as a function of leadership style. On the basis of terror management theory and previous research, we hypothesized that people would show increased preference for a charismatic political candidate and decreased preference for a relationship-oriented political candidate in response to subtle reminders of death. Following a mortality-salience or control induction, 190 participants read campaign statements by charismatic, task-oriented, and relationship-oriented gubernatorial candidates; evaluated their preferences for each candidate; and voted for one of them. Results were in accord with predictions. The theoretical and practical implications of these findings are considered.

  1. Orientation of migratory birds under ultraviolet light.

    Science.gov (United States)

    Wiltschko, Roswitha; Munro, Ursula; Ford, Hugh; Stapput, Katrin; Thalau, Peter; Wiltschko, Wolfgang

    2014-05-01

    In view of the finding that cryptochrome 1a, the putative receptor molecule for the avian magnetic compass, is restricted to the ultraviolet single cones in European Robins, we studied the orientation behaviour of robins and Australian Silvereyes under monochromatic ultraviolet (UV) light. At low intensity UV light of 0.3 mW/m(2), birds showed normal migratory orientation by their inclination compass, with the directional information originating in radical pair processes in the eye. At 2.8 mW/m(2), robins showed an axial preference in the east-west axis, whereas silvereyes preferred an easterly direction. At 5.7 mW/m(2), robins changed direction to a north-south axis. When UV light was combined with yellow light, robins showed easterly 'fixed direction' responses, which changed to disorientation when their upper beak was locally anaesthetised with xylocaine, indicating that they were controlled by the magnetite-based receptors in the beak. Orientation under UV light thus appears to be similar to that observed under blue, turquoise and green light, albeit the UV responses occur at lower light levels, probably because of the greater light sensitivity of the UV cones. The orientation under UV light and green light suggests that at least at the level of the retina, magnetoreception and vision are largely independent of each other.

  2. Orientations of terminal cladodes of Platyopuntias

    Energy Technology Data Exchange (ETDEWEB)

    Nobel, P.S.

    1982-01-01

    The orientations of terminal unshaded cladodes of 23 species of platyopuntias were observed in North America, South America, Australia, and Israel. When the seasonality of rainfall favored cladode development in the winter and the site was located above 27/sup 0/N, the cladodes tended to face north-south (five cases, P < .001 for each). In all other cases without topographical blockage of incoming radiation, the tendency was to face east-west. For example, terminal cladodes of Opuntia phaeacantha var. discata and O. stricta tended to face north-south in Israel but east-west in the United States (P > .001). Such dissimilar orientation patterns also occurred for cladodes of 0. chlorotica at two sites in the Sonoran Desert and for O. basilaris var. basilaris developing at different seasons at a single site. Contrary to previously published observations, cladodes of O. ficus-indica and O. compressa had a significant tendency to orient (P > .001). When topographical features affected the direction of prevailing photosynthetically active radiation (PAR), the preferred orientation of terminal cladodes was changed accordingly. The preferred direction always maximized the interception of PAR, which is often a limiting factor in the productivity of cacti, even in a putatively high radiation environment.

  3. CONSUMPTION IN THE ASPECT OF VALUE ORIENTATIONS

    Directory of Open Access Journals (Sweden)

    Svyatoslav Igorevich Vorojeikin

    2015-01-01

    Full Text Available The article presents a study of the problems of consumption in the aspect of value orientations. The author of the article notes that the study of consumption in modern developed countries of the West led some researchers to the conclusion that consumption becomes for wide masses of population primarily the production of symbols. Being in a group and having a certain status (economic, political, and social, a person must accept the values that are propagated in this group. The author focuses attention on the fact that economic and political status influences the formation of the system of value orientations. Value orientations cover many areas of life, and we can assume that the style of consumer behavior is also influenced by them, i.e. the style of consumer behavior is a kind of confirmation of a certain hierarchy of value orientations. Indeed, the system of value orientations influences the style of consumption. The rules of life can be a source for certain preferences in food, clothing, the ways to meet the needs including spiritual ones, the ways to have a rest and certain services - all this can be seen in terms of the rules of life. The result of the influence of value orientations on the style of consumer behavior is the purchase of certain goods and services.

  4. Archaeoastronomy and the orientation of old churches

    CERN Document Server

    Gangui, Alejandro

    2016-01-01

    Cultural astronomy is an interdisciplinary area of research that studies how perceptions and concepts related to the sky are part of the worldview of a culture. One of its branches, archaeoastronomy, focuses on the material remains of past peoples and tries to investigate their practices and astronomical knowledge. In this context, the orientation of Christian churches is now considered a distinctive feature of their architecture that repeats patterns from early Christian times. There is a general tendency to align their altars in the solar range, with preference for orientations towards the east. Here we present recent data from our measurements of astronomical orientations of old churches located in two --geographically and culturally-- very distant regions, and we discuss the results in the light of the historical and cultural knowledge surrounding these temples.

  5. Archaeoastronomy and the orientation of old churches

    Science.gov (United States)

    Gangui, A.

    2016-08-01

    Cultural astronomy is an interdisciplinary area of research that studies how perceptions and concepts related to the sky are part of the worldview of a culture. One of its branches, archaeoastronomy, focuses on the material remains of past peoples and tries to investigate their practices and astronomical knowledge. In this context, the orientation of Christian churches is now considered a distinctive feature of their architecture that repeats patterns from early Christian times. There is a general tendency to align their altars in the solar range, with preference for orientations towards the east. Here we present recent data from our measurements of astronomical orientations of old churches located in two --geographically and culturally-- very distant regions, and we discuss the results in the light of the historical and cultural knowledge surrounding these temples.

  6. Circadian preference in bipolar disorder.

    Science.gov (United States)

    Giglio, Larriany Maria Falsin; Magalhães, Pedro V S; Andersen, Mônica Levy; Walz, Julio Cesar; Jakobson, Lourenço; Kapczinski, Flávio

    2010-06-01

    A role for circadian rhythm abnormalities in the pathogenesis of bipolar disorder (BD) has been suggested. The present study assessed circadian preference, a subjective preference for activities in the morning or evening related to chronotype. The sample was comprised of 81 outpatients with BD in remission and 79 control subjects. Circadian preference was derived from an interview evaluating biological rhythms and sleep pattern from the Pittsburgh Sleep Quality Index. Patients were significantly more likely to have an evening preference than control subjects. Circadian preference was also associated with sleep latency. The association of evening preference and longer sleep latency may be related to the frequent clinical observation of a sleep/wake cycle reversal in bipolar disorder.

  7. Proper orientation of cacti

    OpenAIRE

    Araujo, Julio; Havet, Frédéric; Linhares Sales, Claudia; Silva, Ana

    2016-01-01

    International audience; An orientation of a graph G is proper if two adjacent vertices have different in-degrees. The proper-orientation number − → χ (G) of a graph G is the minimum maximum in-degree of a proper orientation of G. In [1], the authors ask whether the proper orientation number of a planar graph is bounded. We prove that every cactus admits a proper orientation with maximum in-degree at most 7. We also prove that the bound 7 is tight by showing a cactus having no proper orientati...

  8. Cultural legacies and political preferences

    DEFF Research Database (Denmark)

    Hechter, Michael Norman; Siroky, David; Mueller, Sean

    2015-01-01

    , ecological constraints such as geography and topography affect social interaction with like-minded individuals. On the basis of both these political preferences and ecological constraints, individuals then make rational choices about the desirability of secession. Instrumental considerations are therefore...... that cultural identities matter for explaining secessionism, but not because of primordial attachments. Rather, religious and linguistic groups matter because their members are imbued with cultural legacies that lead to distinct political preferences – in this case preferences over welfare statism. Further...

  9. Orientation dependence of the plastic slip near notches in ductile FCC single crystals

    Science.gov (United States)

    Crone, W. C.; Shield, T. W.; Creuziger, A.; Henneman, B.

    2004-01-01

    Results from experiments conducted on copper FCC single crystals are reported. Two symmetric crystallographic orientations and four nonsymmetric crystallographic orientations were tested. The slip line fields that form near a pre-existing notch in these specimens were observed. The changes in these patterns as the orientation of the notch in the crystal is rotated in an {101} plane are discussed. Sectors of similar slip line patterns are identified and the type of boundaries between these sectors are discussed. A type of sector boundary called mixed kink is identified. Specimen orientations that differ by 90° are found to have different slip line patterns, contrary to the predictions of perfectly plastic slip line theory. The locations of the first slip lines to form are compared to the predictions obtained using anisotropic linear elastic stress field solutions and the initial plane-strain yield surfaces. It is found that comparison of these surface slip line fields to plane strain crack tip solutions in the annular region between 350 and 750 μm is justified. The differences in anisotropic elastic solutions for orientations that are 90° apart explain the lack of agreement with perfectly plastic slip line theory.

  10. Erbium ion implantation into different crystallographic cuts of lithium niobate

    Science.gov (United States)

    Nekvindova, P.; Svecova, B.; Cajzl, J.; Mackova, A.; Malinsky, P.; Oswald, J.; Kolistsch, A.; Spirkova, J.

    2012-02-01

    Single crystals like lithium niobate are frequently doped with optically active rare-earth or transition-metal ions for a variety of applications in optical devices such as solid-state lasers, amplifiers or sensors. To exploit the potential of the Er:LiNbO 3, one must ensure high intensity of the 1.5 μm luminescence as an inevitable prerequisite. One of the important factors influencing the luminescence properties of a lasing ion is the crystal field of the surrounding, which is inevitably determined by the crystal structure of the pertinent material. From that point it is clear that it cannot be easy to affect the resulting luminescence properties - intensity or position of the luminescence band - without changing the structure of the substrate. However, there is a possibility to utilise a potential of the ion implantation of the lasing ions, optionally accompanied with a sensitising one, that can, besides the doping, also modify the structure of the treated area od the crystal. This effect can be eventually enhanced by a post-implantation annealing that may help to recover the damaged structure and hence to improve the desired luminescence. In this paper we are going to report on our experiments with ion-implantation technique followed with subsequent annealing could be a useful way to influence the crystal field of LN. Optically active Er:LiNbO 3 layers were fabricated by medium energy implantation under various experimental conditions. The Er + ions were implanted at energies of 330 and 500 keV with fluences ranging from 1.0 × 10 15 to 1.0 × 10 16 ion cm -2 into LiNbO 3 single-crystal cuts of both common and special orientations. The as-implanted samples were annealed in air and oxygen at two different temperatures (350 and 600 °C) for 5 h. The depth concentration profiles of the implanted erbium were measured by Rutherford Backscattering Spectroscopy (RBS) using 2 MeV He + ions. The photoluminescence spectra of the samples were measured to determine the

  11. Orientalism and India

    Directory of Open Access Journals (Sweden)

    Jukka Jouhki

    2006-01-01

    Full Text Available In this article Orientalism, a special hegemonic discourse about "the Orient" by Europeans is discussed by focusing on how it is manifested in a "Western" view of India. Orientalism as a discourse about the Orient is a concept first coined by Edward Said in his book Orientalism (1978 and contains a long history of European way of relating to the Orient as a counterpart of European/Western culture. In this article Orientalist discourses about India by hegemonically Western (and particularly Anglo-Saxon sources are portrayed and the so-called Indo-Orientalist essentialism defining Indianness from the outside analyzed. Moreover, a Indo-Orientalism as an imported ideology to be used in Indian nationalist discourses to emphasize a dichotomy between India and "the West" is discussed.

  12. Functional implications of orientation maps in primary visual cortex

    Science.gov (United States)

    Koch, Erin; Jin, Jianzhong; Alonso, Jose M.; Zaidi, Qasim

    2016-11-01

    Stimulus orientation in the primary visual cortex of primates and carnivores is mapped as iso-orientation domains radiating from pinwheel centres, where orientation preferences of neighbouring cells change circularly. Whether this orientation map has a function is currently debated, because many mammals, such as rodents, do not have such maps. Here we show that two fundamental properties of visual cortical responses, contrast saturation and cross-orientation suppression, are stronger within cat iso-orientation domains than at pinwheel centres. These differences develop when excitation (not normalization) from neighbouring oriented neurons is applied to different cortical orientation domains and then balanced by inhibition from un-oriented neurons. The functions of the pinwheel mosaic emerge from these local intra-cortical computations: Narrower tuning, greater cross-orientation suppression and higher contrast gain of iso-orientation cells facilitate extraction of object contours from images, whereas broader tuning, greater linearity and less suppression of pinwheel cells generate selectivity for surface patterns and textures.

  13. Preference formation and institutional change

    Directory of Open Access Journals (Sweden)

    Sérgio Praça

    2009-06-01

    Full Text Available This essay critically analyses how historical institutionalists and rational choice scholars study institutional stability and change. Special attention is paid to the thorny issued of how political actors’ preferences are formed, with historical institutionalists considering preferences as endogenously formed, and rational choice analysts postulating that preferences are fixed and exogenous. An argument is made in favour of the perspective that considers preferences as being formed within the functioning of the political system over time, endogenously. The essay also proposes the incorporation of ideas and non-decisions as tools to elucidate processes of change.

  14. Intelligence and musical mode preference

    DEFF Research Database (Denmark)

    Bonetti, Leonardo; Costa, Marco

    2016-01-01

    The relationship between fluid intelligence and preference for major–minor musical mode was investigated in a sample of 80 university students. Intelligence was assessed by the Raven’s Advanced Progressive Matrices. Musical mode preference was assessed by presenting 14 pairs of musical stimuli th...... differences at the cognitive and personality level related to the enjoyment of sad music.......The relationship between fluid intelligence and preference for major–minor musical mode was investigated in a sample of 80 university students. Intelligence was assessed by the Raven’s Advanced Progressive Matrices. Musical mode preference was assessed by presenting 14 pairs of musical stimuli...

  15. EBSD imaging of orientation relationships and variant groupings in different martensitic alloys and Widmanstätten iron meteorites

    Energy Technology Data Exchange (ETDEWEB)

    Cayron, Cyril, E-mail: cyril.cayron@cea.fr

    2014-08-15

    An automatic method to colorize and quantify the classical Pitsch, Kurdjumov–Sachs, Greninger–Troiano and Nishiyama–Wasserman orientation relationships in the electron backscatter diffraction maps of martensitic/bainitic steels is detailed. Automatic analysis of variant grouping is also presented. The method was applied to low and high carbon steels, and to iron–nickel Widmanstätten meteorites. Many results of recent literature are confirmed. In low carbon steels the individual laths exhibit continuous orientation gradients between the classical orientation relationships, and the laths tend to be grouped by close-packed plane (morphological) packets. A crystallographic scenario describing the formation of the packets is proposed on the base of the one-step model. When the carbon content increases, the orientation spreading is reduced; and martensite tends to form plate groups and burst configurations. In iron–nickel meteorites, the centimeter long Widmanstätten laths do not exhibit continuous orientation gradients but are constituted of subgrains with uniform orientation relationship; the kamacite grains in the plessite regions are grouped into Bain zones, probably due to a recrystallization during the slow cooling of the meteorites. - Highlights: • Analysis of different low and high carbon steels and Widmanstätten meteorites • Automatic color mapping of the classical orientation relationships in EBSD maps • Quantification of variant pairing and grouping tendencies • Crystallographic scenario for the formation of morphological packets.

  16. Mutational Studies on Resurrected Ancestral Proteins Reveal Conservation of Site-Specific Amino Acid Preferences throughout Evolutionary History

    Science.gov (United States)

    Risso, Valeria A.; Manssour-Triedo, Fadia; Delgado-Delgado, Asunción; Arco, Rocio; Barroso-delJesus, Alicia; Ingles-Prieto, Alvaro; Godoy-Ruiz, Raquel; Gavira, Jose A.; Gaucher, Eric A.; Ibarra-Molero, Beatriz; Sanchez-Ruiz, Jose M.

    2015-01-01

    Local protein interactions (“molecular context” effects) dictate amino acid replacements and can be described in terms of site-specific, energetic preferences for any different amino acid. It has been recently debated whether these preferences remain approximately constant during evolution or whether, due to coevolution of sites, they change strongly. Such research highlights an unresolved and fundamental issue with far-reaching implications for phylogenetic analysis and molecular evolution modeling. Here, we take advantage of the recent availability of phenotypically supported laboratory resurrections of Precambrian thioredoxins and β-lactamases to experimentally address the change of site-specific amino acid preferences over long geological timescales. Extensive mutational analyses support the notion that evolutionary adjustment to a new amino acid may occur, but to a large extent this is insufficient to erase the primitive preference for amino acid replacements. Generally, site-specific amino acid preferences appear to remain conserved throughout evolutionary history despite local sequence divergence. We show such preference conservation to be readily understandable in molecular terms and we provide crystallographic evidence for an intriguing structural-switch mechanism: Energetic preference for an ancestral amino acid in a modern protein can be linked to reorganization upon mutation to the ancestral local structure around the mutated site. Finally, we point out that site-specific preference conservation naturally leads to one plausible evolutionary explanation for the existence of intragenic global suppressor mutations. PMID:25392342

  17. Effect of oxygen pressure on electrical transport properties for (110) oriented La2/3Sr1/3MnO3 films directly deposited on silicon

    Institute of Scientific and Technical Information of China (English)

    LI Tingxian; LI Kuoshe; YU Dunbo; ZHANG Feipeng; ZHANG Ming; YU Fengjun

    2013-01-01

    La2/3Sr1/3MnO3 films with (110) preferred orientation were deposited on Si (100) substrate without any buffer layer by pulsed laser deposition technique.Effect of oxygen pressure on orientation,surface morphology,and electrical transport properties were investigated.The film deposited at 10 Pa presented (110) preferred orientation with the best crystalline quality,the largest grain size,and the smallest roughness.The (110) oriented film presented higher metal-insulator transition temperature,and the lower resistivity than that of the samples without preferred orientation.

  18. Human preference for air movement

    DEFF Research Database (Denmark)

    Toftum, Jørn; Melikov, Arsen Krikor; Tynel, A.;

    2002-01-01

    Human preference for air movement was studied at slightly cool, neutral, and slightly warm overall thermal sensations and at temperatures ranging from 18 deg.C to 28 deg.C. Air movement preference depended on both thermal sensation and temperature, but large inter-individual differences existed...

  19. Voter-Weighted Environmental Preferences

    Science.gov (United States)

    Bell, Jason; Huber, Joel; Viscusi, W. Kip

    2009-01-01

    This article examines the political economy of preferences with respect to the environment using a new stated preference survey that presents the first benefit values for national water quality levels. The mean valuation greatly exceeds the median value, as the distribution of valuations is highly skewed. The study couples the survey valuations…

  20. Social preferences and portfolio choice

    NARCIS (Netherlands)

    Riedl, A.M.; Smeets, P.M.A.

    2013-01-01

    This paper explores whether social preferences influence portfolio choices of retail investors. We use administrative investor trading records which we link to decisions of the same investors in experiments with real money at stake. We show that social preferences rather than return expectations or

  1. Responding to Students' Learning Preferences in Chemistry

    Science.gov (United States)

    Lewthwaite, Brian; Wiebe, Rick

    2014-04-01

    This paper reports on a teacher's and his students' responsiveness to a new tetrahedral-oriented (Mahaffy in J Chem Educ 83(1):49-55, 2006) curriculum requiring more discursive classroom practices in the teaching of chemistry. In this instrumental case study, we identify the intentions of this learner-centered curriculum and a teacher's development in response to this curriculum. We also explore the tensions this teacher experiences as students subsequently respond to his adjusted teaching. We use a Chemistry Teacher Inventory (Lewthwaite and Wiebe in Res Sci Educ 40(11):667-689, 2011; Lewthwaite and Wiebe in Can J Math Sci Technol Educ 12(1):36-61, 2012; Lewthwaite in Chem Educ Res Pract. doi:10.1039/C3RP00122A, 2014) to assist the teacher in monitoring how he teaches and how he would like to improve his teaching. We also use a student form of the instrument, the Chemistry Classroom Inventory and Classroom Observation Protocol (Lewthwaite and Wiebe 2011) to verify the teacher's teaching and perception of student preferences for his teaching especially in terms of the discursive processes the curriculum encourages. By so doing, the teacher is able to use both sets of data as a foundation for critical reflection and work towards resolution of the incongruence in data arising from students' preferred learning orientations and his teaching aspirations. Implications of this study in regards to the authority of students' voice in triggering teachers' pedagogical change and the adjustments in `teachering' and `studenting' required by such curricula are considered.

  2. The X-ray system of crystallographic programs for any computer having a PIDGIN FORTRAN compiler

    Science.gov (United States)

    Stewart, J. M.; Kruger, G. J.; Ammon, H. L.; Dickinson, C.; Hall, S. R.

    1972-01-01

    A manual is presented for the use of a library of crystallographic programs. This library, called the X-ray system, is designed to carry out the calculations required to solve the structure of crystals by diffraction techniques. It has been implemented at the University of Maryland on the Univac 1108. It has, however, been developed and run on a variety of machines under various operating systems. It is considered to be an essentially machine independent library of applications programs. The report includes definition of crystallographic computing terms, program descriptions, with some text to show their application to specific crystal problems, detailed card input descriptions, mass storage file structure and some example run streams.

  3. Novel Kac-Moody-type affine extensions of non-crystallographic Coxeter groups

    CERN Document Server

    Dechant, Pierre-Philippe; Twarock, Reidun

    2011-01-01

    Motivated by recent results in mathematical virology, we present novel asymmetric Z[tau]-integer-valued affine extensions of the non-crystallographic Coxeter groups H_2, H_3 and H_4 derived in a Kac-Moody-type formalism. In particular, we show that the affine reflection planes which extend the Coxeter group H_3 generate (twist) translations along 2-, 3- and 5-fold axes of icosahedral symmetry and classify these translations in terms of Fibonacci recursion relations, thus providing a framework to explain results of Keef et al and Wardman at the group level. Finally, we extend this classification to the case of the non-crystallographic Coxeter groups H_2 and H_4. These results should have applications in physics (quasicrystals), biology (viruses) and chemistry (fullerenes).

  4. Acanthamoeba polyphaga mimivirus NDK: preliminary crystallographic analysis of the first viral nucleoside diphosphate kinase.

    Science.gov (United States)

    Jeudy, Sandra; Coutard, Bruno; Lebrun, Régine; Abergel, Chantal

    2005-06-01

    The complete sequence of the largest known double-stranded DNA virus, Acanthamoeba polyphaga mimivirus, has recently been determined [Raoult et al. (2004), Science, 306, 1344-1350] and revealed numerous genes not expected to be found in a virus. A comprehensive structural and functional study of these gene products was initiated [Abergel et al. (2005), Acta Cryst. F61, 212-215] both to better understand their role in the virus physiology and to obtain some clues to the origin of DNA viruses. Here, the preliminary crystallographic analysis of the viral nucleoside diphosphate kinase protein is reported. The crystal belongs to the cubic space group P2(1)3, with unit-cell parameter 99.425 A. The self-rotation function confirms that there are two monomers per asymmetric unit related by a twofold non-crystallographic axis and that the unit cell thus contains four biological entities.

  5. Mineralogical, crystallographic and morphological characteristics of natural kaolins from the Ivory Coast (West Africa)

    Science.gov (United States)

    Sei, J.; Morato, F.; Kra, G.; Staunton, S.; Quiquampoix, H.; Jumas, J. C.; Olivier-Fourcade, J.

    2006-10-01

    Thirteen clay samples from four deposits in the Ivory Coast (West Africa) were studied using X-ray diffraction, thermogravimetric analysis and chemical analysis. Mineralogical, crystallographic and morphological characteristics of these samples are given. Kaolinite is the principal mineral but other minerals are present in small quantities: illite, quartz, anatase and iron oxides (oxides and oxyhydroxides). The crystallographic, morphological and surface characteristics are influenced by the presence of these impurities. In particular, the presence of iron oxides was associated with reduced structural ordering and thermal stability of kaolinite and increased specific surface area. These clays could be used in the ceramics industry to make tiles and bricks, and also in agronomy as supports for chemical fertilizers or for environmental protection by immobilising potentially toxic waste products.

  6. Expression, purification and preliminary crystallographic characterization of FlhF from Bacillus subtilis

    Energy Technology Data Exchange (ETDEWEB)

    Bange, Gert; Petzold, Georg; Wild, Klemens; Sinning, Irmgard, E-mail: irmi.sinning@bzh.uni-heidelberg.de [Heidelberg University Biochemistry Centre (BZH), INF 328, 69120 Heidelberg (Germany)

    2007-05-01

    Preliminary crystallographic data are reported for the third SRP GTPase FlhF from Bacillus subtilis. The Gram-positive bacterium Bacillus subtilis contains three proteins belonging to the signal recognition particle (SRP) type GTPase family. The well characterized signal sequence-binding protein SRP54 and the SRP receptor protein FtsY are universally conserved components of the SRP system of protein transport. The third member, FlhF, has been implicated in the placement and assembly of polar flagella. This article describes the overexpression and preliminary X-ray crystallographic analysis of an FlhF fragment that corresponds to the well characterized GTPase domains in SRP54 and FtsY. Three crystal forms are reported with either GDP or GMPPNP and diffract to a resolution of about 3 Å.

  7. Do children prefer mentalistic descriptions?

    Science.gov (United States)

    Dore, Rebecca A; Lillard, Angeline S

    2014-01-01

    Against a long tradition of childhood realism (Piaget, 1929), A. S. Lillard and J. H. Flavell (1990) found that 3-year-olds prefer to characterize people by their mental states (beliefs, desires, emotions) than by their visible behaviors. In this exploratory study, we extend this finding to a new cohort of 3-year-olds, examine how these preferences change from 3-4 years, and explore relationships with theory of mind and parental mind-mindedness. The results showed a developmental change and a possible cohort difference: at 3 years, children in the sample preferred behavioral descriptions, although by 4 years of age, they preferred mentalistic ones. Interestingly, mentalistic preferences were unrelated to theory of mind or parental mind-mindedness, concurrently or over time. Perspective-taking skills at 3 years, however, predicted an increase in mentalistic responses from 3 years to 4 years. Possible explanations for each finding are discussed.

  8. Virtual Orienteering Game For Smartphones

    OpenAIRE

    Sainio, Kari

    2015-01-01

    Orienteering is a relatively famous sports activity in Nordic countries. Today technology provides attractive means for transition from traditional orienteering to virtual orienteering. Virtual orienteering can be thought as orienteering without using a traditional printed map and compass. On the other hand smartphones contain technology for implementing virtual orienteering. There are different smartphone platforms and types, making application development challenging because several cod...

  9. PREFERENCE THEORY IN ADVANCED AGE AND THE OLDER CZECH WORKFORCE

    Directory of Open Access Journals (Sweden)

    Lucie Vidovićová

    2015-07-01

    Full Text Available In this article we make use of preference theory developed by Hakim (2000 in the context of reconciling work and family to cover and explain different patterns of retirement exit paths and retirement satisfaction levels in the Czech Republic. We propose that lifestyle preferences and values may help to explain why some older workers continue to work while others are determined to retire as early as possible. Three types are identified among the 55–65 age group: work oriented, retirement oriented, and adaptive. The data shows that self-perception of the respondent as being active or more rest-oriented is associated with actual labour market activity of the respondent. Different types also perceive and evaluate labour market exit differently, and most importantly they differ in their reaction to various labour market and pension policies and family/partnership conditions. In the discussion we challenge the notion of active ageing as a general “one-size-fits-all” policy and urge that more attention be paid to the role of individual values and preferences when looking at the organisation of latter life roles.

  10. Microstructure, crystallographic texture and mechanical properties of friction stir welded AA2017A

    Energy Technology Data Exchange (ETDEWEB)

    Ahmed, M.M.Z., E-mail: mohamed_ahmed4@s-petrol.suez.edu.eg [Institute for Microstructural and Mechanical Processing Engineering, University of Sheffield (IMMPETUS), Mappin Street, Sheffield S1 3JD (United Kingdom); Department of Metallurgical and Materials Engineering, Suez Canal University, Suez 43721 (Egypt); Wynne, B.P.; Rainforth, W.M. [Institute for Microstructural and Mechanical Processing Engineering, University of Sheffield (IMMPETUS), Mappin Street, Sheffield S1 3JD (United Kingdom); Threadgill, P.L. [TWI LTD, Granta Park, Great Abington, Cambridge CB21 6AL (United Kingdom)

    2012-02-15

    In this study a thick section (20 mm) friction stir welded AA2017A-T451 has been characterized in terms of microstructure, crystallographic texture and mechanical properties. For microstructural analysis both optical and scanning electron microscopes have been used. A detailed crystallographic texture analysis has been carried out using the electron back scattering diffraction technique. Crystallographic texture has been examined in both shoulder and probe affected regions of the weld NG. An entirely weak texture is observed at the shoulder affected region which is mainly explained by the effect of the sequential multi pass deformation experienced by both tool probe and tool shoulder. The texture in the probe dominated region at the AS side of the weld is relatively weak but still assembles the simple shear texture of FCC metals with B/B{sup Macron} and C components existing across the whole map. However, the texture is stronger at the RS than at the AS of the weld, mainly dominated byB/B{sup Macron} components and with C component almost absent across the map. An alternating bands between (B) components and (B{sup Macron }) component are observed only at the AS side of the weld. - Highlights: Black-Right-Pointing-Pointer Detailed investigation of microstructure and crystallographic texture. Black-Right-Pointing-Pointer The grain size is varied from the top to the bottom of the NG. Black-Right-Pointing-Pointer An entirely weak texture is observed at the shoulder affected region. Black-Right-Pointing-Pointer The texture in the probe affected region is dominated by simple shear texture.

  11. Crystallographic mechanism of inverse twinning in ordered β′-CuZn alloy

    Institute of Scientific and Technical Information of China (English)

    毛卫民

    2000-01-01

    The basic process of mechanical twinning in β’-CuZn phase, as an example of B2 structured metals, has been analyzed under the rolling stresses. The behavior of inverse twinning in B2 structured metals is discussed in terms of mechanics and crystallographic stability. It is shown that the inverse twinning could remain the B2 structure, and the resulting strains will have the lowest resistance during the rolling deformation of the polycrystalline.

  12. Crystallographic mechanism of inverse twinning in ordered β'-CuZn alloy

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The basic process of mechanical twinning in β'-CuZn phase, as an example of B2 structured metals, has been analyzed under the rolling stresses. The behavior of inverse twinning in B2 structured metals is discussed in terms of mechanics and crystallographic stability. It is shown that the inverse twinning could remain the B2 structure, and the resulting strains will have the lowest resistance during the rolling deformation of the polycrystalline.

  13. Crystallization and preliminary crystallographic characterization of an SH3 domain from the IB1 scaffold protein

    DEFF Research Database (Denmark)

    Dar, Imran; Bonny, Christophe; Pedersen, Jan Torleif

    2003-01-01

    with unmodified protein and deliberately oxidized protein have led to different crystal forms. X-ray data have been collected to 3.0 A resolution from a crystal form with rectangular prism morphology. These crystals are orthorhombic (P2(1)2(1)2(1)), with unit-cell parameters a = 45.9, b = 57.0, c = 145.5 A....... These are the first crystallographic data on a scaffold molecule such as IB1 to be reported....

  14. Keep it together: restraints in crystallographic refinement of macromolecule–ligand complexes

    Science.gov (United States)

    Steiner, Roberto A.; Tucker, Julie A.

    2017-01-01

    A short introduction is provided to the concept of restraints in macromolecular crystallographic refinement. A typical ligand restraint-generation process is then described, covering types of input, the methodology and the mechanics behind the software in general terms, how this has evolved over recent years and what to look for in the output. Finally, the currently available restraint-generation software is compared, concluding with some thoughts for the future. PMID:28177305

  15. Affine extensions of non-crystallographic Coxeter groups induced by projection

    Science.gov (United States)

    Dechant, Pierre-Philippe; BÅ`hm, Céline; Twarock, Reidun

    2013-09-01

    In this paper, we show that affine extensions of non-crystallographic Coxeter groups can be derived via Coxeter-Dynkin diagram foldings and projections of affine extended versions of the root systems E8, D6, and A4. We show that the induced affine extensions of the non-crystallographic groups H4, H3, and H2 correspond to a distinguished subset of those considered in [P.-P. Dechant, C. Bœhm, and R. Twarock, J. Phys. A: Math. Theor. 45, 285202 (2012)]. This class of extensions was motivated by physical applications in icosahedral systems in biology (viruses), physics (quasicrystals), and chemistry (fullerenes). By connecting these here to extensions of E8, D6, and A4, we place them into the broader context of crystallographic lattices such as E8, suggesting their potential for applications in high energy physics, integrable systems, and modular form theory. By inverting the projection, we make the case for admitting different number fields in the Cartan matrix, which could open up enticing possibilities in hyperbolic geometry and rational conformal field theory.

  16. Electron diffraction study of {alpha}-AlMnSi crystals including non-crystallographic axes

    Energy Technology Data Exchange (ETDEWEB)

    Song, G.L.; Bursill, L.A.

    1997-06-01

    The structure of crystalline {alpha}-AlMnSi is examined by electron diffraction. Six distinct zone axes are examined, including both normal crystallographic and non-crystallographic zones axes, allowing the space group symmetry to be studied. Electron diffraction patterns characteristic of Pm3-bar were obtained for thicker specimens. However, for very thin specimens, as used for HRTEM imaging, the electron diffraction patterns were characteristic of Im3-bar space group symmetry. The structural basis of the Pm3-bar to Im3-bar transformation may be understood in terms of an analysis of the icosahedral structural elements located at the corners and body-centers of the cubic unit cell. A method for indexing the non-crystallographic zone axis diffraction patterns is described. An electron diffraction pattern of the 5-fold axis of the quasicrystalline phase i-AlMnSi is also included; this is compared with the experimental results and calculations for the [0{tau}1] axis of Pm3-bar and Im3-bar crystalline phases. 26 refs., 4 tabs., 7 figs.

  17. Rapid Creation of Three-Dimensional, Tactile Models from Crystallographic Data

    Directory of Open Access Journals (Sweden)

    Nathan B. Fisher

    2016-01-01

    Full Text Available A method for the conversion of crystallographic information framework (CIF files to stereo lithographic data files suitable for printing on three-dimensional printers is presented. Crystallographic information framework or CIF files are capable of being manipulated in virtual space by a variety of computer programs, but their visual representations are limited to the two-dimensional surface of the computer screen. Tactile molecular models that demonstrate critical ideas, such as symmetry elements, play a critical role in enabling new students to fully visualize crystallographic concepts. In the past five years, major developments in three-dimensional printing has lowered the cost and complexity of these systems to a level where three-dimensional molecular models may be easily created provided that the data exists in a suitable format. Herein a method is described for the conversion of CIF file data using existing free software that allows for the rapid creation of inexpensive molecular models. This approach has numerous potential applications in basic research, education, visualization, and crystallography.

  18. Entrepreneurial Orientation and Internationalisation

    DEFF Research Database (Denmark)

    Decker, Arnim; Rollnik-Sadowska, Ewa; Servais, Per

    Entrepreneurial orientation is a multidimensional construct that determines the strategic posture of a firm. In this study we investigate a sample of six manufacturing firms which are located both in a remote area and in a transition economy. Through interpreting the construct of entrepreneurial...... orientation as an attitude held by principals we investigate how entrepreneurial orientation affected the behaviour of these firms, specifically in terms of their internationalisation. Despite the fact that all firms have identical roots we find that entrepreneurial orientation held by their principals affect...

  19. Orientation selectivity with organic photodetectors and an organic electrochemical transistor

    Science.gov (United States)

    Gkoupidenis, Paschalis; Rezaei-Mazinani, Shahab; Proctor, Christopher M.; Ismailova, Esma; Malliaras, George G.

    2016-11-01

    Neuroinspired device architectures offer the potential of higher order functionalities in information processing beyond their traditional microelectronic counterparts. Here we demonstrate a neuromorphic function of orientation selectivity, which is inspired from the visual system, with a combination of organic photodetectors and a multi-gated organic electrochemical transistor based on poly(3,4ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS). The device platform responds preferably to different orientations of light bars, a behaviour that resembles orientation selectivity of visual cortex cells. These results pave the way for organic-based neuromorphic devices with spatially correlated functionalities and potential applications in the area of organic bioelectronics.

  20. Planning with Partial Preference Models

    CERN Document Server

    Nguyen, Tuan; Gerevini, Alfonso; Serina, Ivan; Srivastava, Biplav; Kambhampati, Subbarao

    2011-01-01

    Current work in planning with preferences assume that the user's preference models are completely specified and aim to search for a single solution plan. In many real-world planning scenarios, however, the user probably cannot provide any information about her desired plans, or in some cases can only express partial preferences. In such situations, the planner has to present not only one but a set of plans to the user, with the hope that some of them are similar to the plan she prefers. We first propose the usage of different measures to capture quality of plan sets that are suitable for such scenarios: domain-independent distance measures defined based on plan elements (actions, states, causal links) if no knowledge of the user's preferences is given, and the Integrated Convex Preference measure in case the user's partial preference is provided. We then investigate various heuristic approaches to find set of plans according to these measures, and present empirical results demonstrating the promise of our app...

  1. Crystallographic groups and topology in Escher. (Spanish:Grupos cristalográficos y topología en Escher).

    OpenAIRE

    Montesinos Amilibia, José María

    2010-01-01

    In the late 19th century Fedorov, Schoenflies, and Barlow classified the seventeen wallpaper groups (two-dimensional crystallographic groups, five of them direct movements and twelve of them inverse movements) and the 320 three-dimensional crystallographic groups. In order to get the lists of groups, they all used the same geometric strategy: to combine all possible movements and study them case by case. Later on, Zassenhaus developed a purely algebraic algorithm which allowed him to u...

  2. The do re mi's of everyday life: the structure and personality correlates of music preferences.

    Science.gov (United States)

    Rentfrow, Peter J; Gosling, Samuel D

    2003-06-01

    The present research examined individual differences in music preferences. A series of 6 studies investigated lay beliefs about music, the structure underlying music preferences, and the links between music preferences and personality. The data indicated that people consider music an important aspect of their lives and listening to music an activity they engaged in frequently. Using multiple samples, methods, and geographic regions, analyses of the music preferences of over 3,500 individuals converged to reveal 4 music-preference dimensions: Reflective and Complex, Intense and Rebellious, Upbeat and Conventional, and Energetic and Rhythmic. Preferences for these music dimensions were related to a wide array of personality dimensions (e.g., Openness), self-views (e.g., political orientation), and cognitive abilities (e.g., verbal IQ).

  3. Elicitation of ostomy pouch preferences

    DEFF Research Database (Denmark)

    Bonnichsen, Ole

    2011-01-01

    in ostomy pouch attributes. The theory, study design, elicitation procedure, and resulting preference structure of the sample is described. Methods: A discrete-choice experiment (DCE) was used to elicit preferences. Respondents were asked to choose between alternatives in choice sets, in which each...... pouches when cost is included as an attribute. A total of 254 patients responded to the survey and preferences were estimated using a random parameter logit econometric specification. Results: Respondents had significantly positive WTP for all potential attribute improvements presented in the survey...

  4. Preferences for Simultaneous Polydrug Use:

    DEFF Research Database (Denmark)

    Østergaard, Jeanette; Østergaard, Stine Vernstrøm; Fletcher, Adam

    2016-01-01

    use (PSPU) vary among club/bar-goers in two European countries, Denmark and England, typically cited as exemplars of the normalization of illegal drug use. The study considers the utility of the normalization thesis for understanding preferences for polydrug use in the European nighttime economy....... Lifetime cocaine use was 38% in England and 17% in Denmark. In England, young adults with drug experience preferred to mix alcohol with cocaine (65%). In Denmark, young adults with drug experience preferred to mix alcohol with cannabis (78%). In multinominal regression, Danish young adults’ educational...

  5. Stated preference methods using R

    CERN Document Server

    Aizaki, Hideo; Sato, Kazuo

    2014-01-01

    Stated Preference Methods Using R explains how to use stated preference (SP) methods, which are a family of survey methods, to measure people's preferences based on decision making in hypothetical choice situations. Along with giving introductory explanations of the methods, the book collates information on existing R functions and packages as well as those prepared by the authors. It focuses on core SP methods, including contingent valuation (CV), discrete choice experiments (DCEs), and best-worst scaling (BWS). Several example data sets illustrate empirical applications of each method with R

  6. Endogenous scheduling preferences and congestion

    DEFF Research Database (Denmark)

    Fosgerau, Mogens; Small, Kenneth

    2010-01-01

    Dynamic models of congestion so far rely on exogenous scheduling preferences of travelers, based for example on disutility of deviation from a preferred departure or arrival time for a trip. This paper provides a more fundamental view in which travelers derive utility just from consumption...... and leisure, but agglomeration economies at home and at work lead to scheduling preferences forming endogenously. Using bottleneck congestion technology, we obtain an equilibrium queuing pattern consistent with a general version of the Vickrey bottleneck model. However, the policy implications are different...

  7. Sexual Orientation and Choice

    Directory of Open Access Journals (Sweden)

    Ayala Saray

    2017-07-01

    Full Text Available Is there a choice in sexual orientation? [Wilkerson, William S. (2009: “Is It a Choice? Sexual Orientation as Interpretation”. In: Journal of Social Philosophy 40. No. 1, p. 97–116] argues that sexual desires require interpretation in order to be fully constituted, and therefore sexual orientation is at least partially constituted by choice. [Díaz-León, Esa (2017: “Sexual Orientation as Interpretation? Sexual Desires, Concepts, and Choice”; In: Journal of Social Ontology] critically assesses Wilkerson’s argument, concluding that we still lack a good argument for the claim that choice plays a role in sexual orientation. Here I examine Díaz-León’s response to Wilkerson. I introduce what I call the conceptual act theory of sexual orientation, and argue that even if interpretation were not necessary to constitute sexual desires, it is a necessary element to constitute what we call sexual orientation. However, I conclude that even if we agree that interpretation is involved in sexual orientation, it does not follow that there is a choice involved.

  8. Edward Said and "Orientalism"

    Science.gov (United States)

    Chronicle of Higher Education, 2007

    2007-01-01

    In the nearly 30 years since Edward Said published the hugely influential Orientalism, his indictment of racism and imperialism in Western scholarship on the Orient has had its share of plaudits and condemnations. Now Robert Irwin, the Middle East editor of The Times Literary Supplement, has reignited the controversy with his broadside against the…

  9. Orientalism/Occidentalism

    NARCIS (Netherlands)

    Minca, C.; Ong, C.E.

    2017-01-01

    Orientalism and Occidentalism are interrelated concepts. Orientalism is defined in three keys ways: (i) as a study of “the Orient”; (ii) as a cultural and aesthetic concern with “the Orient”; and (iii) as a critical approach to understanding the construction of “the Orient” by European and American

  10. Teaching Orienteering. Second Edition.

    Science.gov (United States)

    McNeill, Carol; Cory-Wright, Jean; Renfrew, Tom

    The educational value provided by orienteering's blend of navigational and physical skills has given it a permanent place in the primary and secondary school curriculum in the United Kingdom. This book is a reference to orienteering for teachers, leaders, and coaches. It provides a "how to" approach to introducing and developing the…

  11. Orienteering in Camping.

    Science.gov (United States)

    Larson, Elston F.

    One of the recent developments in camping is "orienteering", a program using a map and compass. Orienteering can be dovetailed into an overall camping program and used to "point up" the entire program, or it can be confined to a single simple game. The arrangement depends on the situation. The minimum age of the participants should be about 9 or…

  12. Decision Making In Orienteering.

    Science.gov (United States)

    Almeida, Katia

    1997-01-01

    Eight psychometric instruments were administered to 10 elite male Portuguese orienteers. The cognitive process involved in decision making did not differ between the best orienteers and the others. This group of athletes had a high capacity for work realization and a strong need to be in control of interpersonal situations. (Author/SV)

  13. Wildlife value orientations

    DEFF Research Database (Denmark)

    Gamborg, Christian; Jensen, Frank Søndergaard

    2016-01-01

    This article examined value orientations toward wildlife among the adult general Danish public in relation to age, sex, past and present residence, education, and income, using a U.S. survey instrument on Wildlife Value Orientations (WVO). The study used an Internet-based questionnaire sent...

  14. Social Dominance Orientation, Right-Wing Authoritarianism, Sexism, and Prejudice toward Women in the Workforce

    Science.gov (United States)

    Christopher, Andrew N.; Wojda, Mark R.

    2008-01-01

    This study examined how social dominance orientation (SDO) and right-wing authoritarianism (RWA) were related to two different forms of prejudice against working women: employment skepticism and traditional role preference. Three hundred forty-nine American adults completed measures of SDO, RWA, employment skepticism, traditional role preference,…

  15. Magnetosensitive neurons mediate geomagnetic orientation in Caenorhabditis elegans.

    Science.gov (United States)

    Vidal-Gadea, Andrés; Ward, Kristi; Beron, Celia; Ghorashian, Navid; Gokce, Sertan; Russell, Joshua; Truong, Nicholas; Parikh, Adhishri; Gadea, Otilia; Ben-Yakar, Adela; Pierce-Shimomura, Jonathan

    2015-06-17

    Many organisms spanning from bacteria to mammals orient to the earth's magnetic field. For a few animals, central neurons responsive to earth-strength magnetic fields have been identified; however, magnetosensory neurons have yet to be identified in any animal. We show that the nematode Caenorhabditis elegans orients to the earth's magnetic field during vertical burrowing migrations. Well-fed worms migrated up, while starved worms migrated down. Populations isolated from around the world, migrated at angles to the magnetic vector that would optimize vertical translation in their native soil, with northern- and southern-hemisphere worms displaying opposite migratory preferences. Magnetic orientation and vertical migrations required the TAX-4 cyclic nucleotide-gated ion channel in the AFD sensory neuron pair. Calcium imaging showed that these neurons respond to magnetic fields even without synaptic input. C. elegans may have adapted magnetic orientation to simplify their vertical burrowing migration by reducing the orientation task from three dimensions to one.

  16. Fabrication of (110)-one-axis-oriented perovskite-type oxide thin films and their application to buffer layer

    Science.gov (United States)

    Sato, Tomoya; Ichinose, Daichi; Kimura, Junichi; Inoue, Takaaki; Mimura, Takanori; Funakubo, Hiroshi; Uchiyama, Kiyoshi

    2016-10-01

    BaCe0.9Y0.1O3-δ (BCYO) and SrZr0.8Y0.2O3-δ (SZYO) thin films of perovskite-type oxides were deposited on (111)Pt/TiO x /SiO2/(100)Si substrates. X-ray diffraction patterns showed that the (110)-oriented BCYO and SZYO thin films were grown on (111)Pt/Si substrates directly without using any buffer layers. Thin films of SrRuO3 (SRO), a conductive perovskite-type oxide, were also deposited on those films and highly (110)-oriented SRO thin films were obtained. We believe that this (110)-oriented SRO works as a buffer layer to deposit (110)-oriented perovskite-type ferroelectric oxide thin films as well as a bottom electrode and can modify the ferroelectric properties of the oxide thin films by controlling their crystallographic orientations.

  17. Review - Fabrication of crystal-oriented barium-bismuth titanate ceramics in high magnetic field and subsequent reaction sintering

    Directory of Open Access Journals (Sweden)

    Satoshi Tanaka, Yusuke Tomita, Ryoichi Furushima, Hiroyuki Shimizu, Yutaka Doshida and Keizo Uematsu

    2009-01-01

    Full Text Available High magnetic field was applied to fabricate novel lead-free piezoelectric ceramics with a textured structure. A compact of crystallographically oriented grains was prepared by dry forming in a high magnetic field from a mixed slurry of bismuth titanate and barium titanate powders. Bismuth titanate particles with a size of about 1 μ m were used as the host material. In the forming process, the slurry was poured into a mold and set in a magnetic field of 10 T until completely dried. Bismuth titanate particles were highly oriented in the slurry under the magnetic field. The dried powder compact consisted of highly oriented bismuth titanate particles and randomly oriented barium titanate particles. Barium bismuth titanate ceramics with a- and b-axis orientations were successfully produced from the dried compact by sintering at temperatures above 1100 ° C.

  18. Polarization Manipulation via Orientation Control in Polycrystalline BiFeO3 Thin Films on Biaxially Textured, Flexible Metallic Tapes

    Science.gov (United States)

    Shin, Junsoo; Goyal, Amit; Jesse, Stephen; Heatherly, Lee

    2011-02-01

    (111)-, (101)-, and (001)-oriented polycrystalline BiFeO3 films were fabricated on rolling-assisted biaxially textured substrates (RABiTS) with appropriate engineering of heteroepitaxially grown buffer multilayers on RABiTS. The crystallographic orientation and polarization direction were confirmed using X-ray diffraction and piezoresponse force microscopy (PFM), respectively. All the films exhibited excellent piezoelectric properties. Switching spectroscopy PFM demonstrated that the switching polarization in (111)-oriented polycrystalline BiFeO3 films is higher than that in (101)- or (001)-oriented films. These BiFeO3 films on low-cost, flexible, biaxially textured metallic tapes with controllable orientation and polarization are attractive for application in flexible piezoelectric devices.

  19. Endogenous scheduling preferences and congestion

    DEFF Research Database (Denmark)

    Fosgerau, Mogens; Small, Kenneth

    2010-01-01

    Dynamic models of congestion so far rely on exogenous scheduling preferences of travelers, based for example on disutility of deviation from a preferred departure or arrival time for a trip. This paper provides a more fundamental view in which travelers derive utility just from consumption...... and leisure, but agglomeration economies at home and at work lead to scheduling preferences forming endogenously. Using bottleneck congestion technology, we obtain an equilibrium queuing pattern consistent with a general version of the Vickrey bottleneck model. However, the policy implications are different....... Compared to the predictions of an analyst observing untolled equilibrium and taking scheduling preferences as exogenous, we find that both the optimal capacity and the marginal external cost of congestion have changed. The benefits of tolling are greater, and the optimal time varying toll is different....

  20. Preferences With Grades of Indecisiveness

    OpenAIRE

    Stefania Minardi; Andrei Savochkin

    2013-01-01

    Departing from the traditional approach to modeling an agent who finds it difficult to make clear-cut comparisons between alternatives, we introduce the notion of graded preferences: Given two alternatives, the agent reports a number between 0 and 1, which reflects her inclination to prefer the first option over the second or, put differently, how confident she is about the superiority of the first one. In the classical framework of uncertainty, we derive a representation of a graded preferen...

  1. Preferred extensions as stable models

    OpenAIRE

    2008-01-01

    Given an argumentation framework AF, we introduce a mapping function that constructs a disjunctive logic program P, such that the preferred extensions of AF correspond to the stable models of P, after intersecting each stable model with the relevant atoms. The given mapping function is of polynomial size w.r.t. AF. In particular, we identify that there is a direct relationship between the minimal models of a propositional formula and the preferred extensions of an argumentation framework by w...

  2. Gender Differences in Investment Preferences

    OpenAIRE

    Nizamettin Bayyurt; Vildan Karisik; Ali Coskun

    2016-01-01

    The paper attempts to explore how women and men differ in their individual investment preferences. Although there are some studies for the investors in developed countries, the subject has been overlooked in emerging and underdeveloped countries. Therefore, this study is the first empirical study exploring the investment behaviors of women and men by focusing on an emerging country, Turkey. For the purpose to find out how investment preferences of men and women differ towards s...

  3. Human preference for individual colors

    Science.gov (United States)

    Palmer, Stephen E.; Schloss, Karen B.

    2010-02-01

    Color preference is an important aspect of human behavior, but little is known about why people like some colors more than others. Recent results from the Berkeley Color Project (BCP) provide detailed measurements of preferences among 32 chromatic colors as well as other relevant aspects of color perception. We describe the fit of several color preference models, including ones based on cone outputs, color-emotion associations, and Palmer and Schloss's ecological valence theory. The ecological valence theory postulates that color serves an adaptive "steering' function, analogous to taste preferences, biasing organisms to approach advantageous objects and avoid disadvantageous ones. It predicts that people will tend to like colors to the extent that they like the objects that are characteristically that color, averaged over all such objects. The ecological valence theory predicts 80% of the variance in average color preference ratings from the Weighted Affective Valence Estimates (WAVEs) of correspondingly colored objects, much more variance than any of the other models. We also describe how hue preferences for single colors differ as a function of gender, expertise, culture, social institutions, and perceptual experience.

  4. Project Organizations and Their Present and Preferred Culture

    Directory of Open Access Journals (Sweden)

    Lajos SZABO

    2015-12-01

    Full Text Available Although several research has investigated organizational culture (Schein, 2010; Alvesson, 2013, less research has been conducted on the comparison of present and preferred cultures in project context. This paper aims to fill this gap by focusing on project managers and on the investigation of the present and the preferred culture profile of their project organizations. Based on Cameron and Quinn's (2011 Competing Values Framework using the Organizational Culture Assessment Instrument a quantitative survey was conducted. The questionnaire used gathered data from project managers working in various industries and organizations. The sample consisted of 695 respondents. The empirical study by focusing on project organizations hypothesizes that four project organization groups can be revealed based on their dominant cultural orientation. To test this hypothesis cluster analysis was used. The study also hypothesizes that the present and preferred culture profiles of project organizations do not show significant difference. To prove this statement paired samples t-test was chosen. The results showed that instead of four groups of project organizations with one dominant culture type, there are only three project organizations with the domination of one culture type. Continuing the investigation with these three project organizations, the present and preferred project culture profiles were compared. The results showed that in all three project organizations there are differences between the present and preferred project culture profiles. These differences are manifested mainly by the change of the dominant culture type but the remaining culture types determining the culture profile of the project organizations also show differences.

  5. Mechanism of Calcite Co-Orientation in the Sea Urchin Tooth

    Energy Technology Data Exchange (ETDEWEB)

    Killian, Christopher; Metzler, Rebecca; Gong, Y. U. T.; Olson, Ian; Aizenberg, Joanna; Politi, Yael; Wilt, Fred; Scholl, Andreas; Young, Anthony; Doran, Andrew; Kunz, Martin; Tamura, Nobumichi; Coppersmith, Susan; Gilbert, P. U. P. A.

    2009-12-01

    Sea urchin teeth are remarkable and complex calcite structures, continuously growing at the forming end and self-sharpening at the mature grinding tip. The calcite (CaCO{sub 3}) crystals of tooth components, plates, fibers, and a high-Mg polycrystalline matrix, have highly co-oriented crystallographic axes. This ability to co-orient calcite in a mineralized structure is shared by all echinoderms. However, the physico-chemical mechanism by which calcite crystals become co-oriented in echinoderms remains enigmatic. Here, we show differences in calcite c-axis orientations in the tooth of the purple sea urchin (Strongylocentrotus purpuratus), using high-resolution X-ray photoelectron emission spectromicroscopy (X-PEEM) and microbeam X-ray diffraction ({mu}XRD). All plates share one crystal orientation, propagated through pillar bridges, while fibers and polycrystalline matrix share another orientation. Furthermore, in the forming end of the tooth, we observe that CaCO{sub 3} is present as amorphous calcium carbonate (ACC). We demonstrate that co-orientation of the nanoparticles in the polycrystalline matrix occurs via solid-state secondary nucleation, propagating out from the previously formed fibers and plates, into the amorphous precursor nanoparticles. Because amorphous precursors were observed in diverse biominerals, solid-state secondary nucleation is likely to be a general mechanism for the co-orientation of biomineral components in organisms from different phyla.

  6. (001) Oriented piezoelectric films prepared by chemical solution deposition on Ni foils

    Energy Technology Data Exchange (ETDEWEB)

    Yeo, Hong Goo, E-mail: hxy162@psu.edu; Trolier-McKinstry, Susan [Materials Research Institute, The Pennsylvania State University, University Park, Pennsylvania 16802 (United States)

    2014-07-07

    Flexible metal foil substrates are useful in some microelectromechanical systems applications including wearable piezoelectric sensors or energy harvesters based on Pb(Zr,Ti)O₃ (PZT) thin films. Full utilization of the potential of piezoelectrics on metal foils requires control of the film crystallographic texture. In this study, (001) oriented PZT thin films were grown by chemical solution deposition (CSD) on Ni foil and Si substrates. Ni foils were passivated using HfO₂ grown by atomic layer deposition in order to suppress substrate oxidation during subsequent thermal treatment. To obtain the desired orientation of PZT film, strongly (100) oriented LaNiO₃ films were integrated by CSD on the HfO₂ coated substrates. A high level of (001) LaNiO₃ and PZT film orientation were confirmed by X-ray diffraction patterns. Before poling, the low field dielectric permittivity and loss tangents of (001) oriented PZT films on Ni are near 780 and 0.04 at 1 kHz; the permittivity drops significantly on poling due to in-plane to out-of-plane domain switching. (001) oriented PZT film on Ni displayed a well-saturated hysteresis loop with a large remanent polarization ~36 μC/cm², while (100) oriented PZT on Si showed slanted P-E hysteresis loops with much lower remanent polarizations. The |e{sub 31,f}| piezoelectric coefficient was around 10.6 C/m² for hot-poled (001) oriented PZT film on Ni.

  7. Effects of mobile map orientation and tactile feedback on navigation speed and situation awareness

    NARCIS (Netherlands)

    doi:10.1145/1409240.1409249; Smets, N.J.J.M.; Brake, G.M. te; Lindenberg, J.; Neerincx, M.A.

    2008-01-01

    Mobile information systems aid first responders in their tasks. Support is often based on mobile maps. People have different preferences for map orientations (heading-up or north-up), but map orientations also have different advantages and disadvantages. In general north-up maps are good for buildin

  8. The Relation between Gender Role Orientation and Fear and Anxiety in Nonclinic-Referred Children

    Science.gov (United States)

    Muris, Peter; Meesters, Cor; Knoops, Miranda

    2005-01-01

    This study examined the relation between gender role orientation and fear and anxiety in a sample of nonclinic-referred children (N = 209) ages 10 to 13 years. Children and their parents completed questionnaires assessing children's gender role orientation, toy and activity preferences, and fear and anxiety. Results generally indicated that…

  9. Cross-national differences in price–role orientation and their impact on retail markets

    DEFF Research Database (Denmark)

    Zielke, Stephan; Komor, Marcin

    2015-01-01

    This paper analyzes differences in price–role orientations between economically developed and emerging markets and how these differences influence store brand and store format preferences. It extends cross-national research on price–role orientations by (1) focusing on culturally similar...

  10. Learning strategy preferences, verbal-visual cognitive styles, and multimedia preferences for continuing engineering education instructional design

    Science.gov (United States)

    Baukal, Charles Edward, Jr.

    A literature search revealed very little information on how to teach working engineers, which became the motivation for this research. Effective training is important for many reasons such as preventing accidents, maximizing fuel efficiency, minimizing pollution emissions, and reducing equipment downtime. The conceptual framework for this study included the development of a new instructional design framework called the Multimedia Cone of Abstraction (MCoA). This was developed by combining Dale's Cone of Experience and Mayer's Cognitive Theory of Multimedia Learning. An anonymous survey of 118 engineers from a single Midwestern manufacturer was conducted to determine their demographics, learning strategy preferences, verbal-visual cognitive styles, and multimedia preferences. The learning strategy preference profile and verbal-visual cognitive styles of the sample were statistically significantly different than the general population. The working engineers included more Problem Solvers and were much more visually-oriented than the general population. To study multimedia preferences, five of the seven levels in the MCoA were used. Eight types of multimedia were compared in four categories (types in parantheses): text (text and narration), static graphics (drawing and photograph), non-interactive dynamic graphics (animation and video), and interactive dynamic graphics (simulated virtual reality and real virtual reality). The first phase of the study examined multimedia preferences within a category. Participants compared multimedia types in pairs on dual screens using relative preference, rating, and ranking. Surprisingly, the more abstract multimedia (text, drawing, animation, and simulated virtual reality) were preferred in every category to the more concrete multimedia (narration, photograph, video, and real virtual reality), despite the fact that most participants had relatively little prior subject knowledge. However, the more abstract graphics were only slightly

  11. Intrinsic and extrinsic motivational orientations in the competitive context: an examination of person-situation interactions.

    Science.gov (United States)

    Abuhamdeh, Sami; Csikszentmihalyi, Mihaly

    2009-10-01

    The current study examined Intrinsic Motivation Orientation and Extrinsic Motivation Orientation (Work Preference Inventory; Amabile, Hill, Hennessey, & Tighe, 1994) as potential trait-level moderators of the way Internet chess players responded to the intrinsic and extrinsic rewards of the chess games they played. On the basis of the defining characteristics of these 2 types of motivational orientations, we predicted that (a) Intrinsic Motivation Orientation would be associated with a stronger curvilinear relationship between challenge and enjoyment and (b) Extrinsic Motivation Orientation would be associated with a heightened affective responsivity to competitive outcome (i.e., winning vs. losing). Results supported the predictions. Implications of the findings are discussed.

  12. Heterogeneous Consumer Preferences for Nanotechnology and Genetic-Modification Technology in Food Products

    OpenAIRE

    2014-01-01

    This study investigates heterogeneous consumer preferences for nano-food and genetic-modified (GM) food and the associated benefits using the results of choice experiments with 1117 U.S. consumers. We employ a mixed logit model and a latent class logit model to capture the heterogeneity in consumer preferences by identifying consumer segments. Our results show that nano-food evokes less negative reactions compared with GM food. We identify four consumer groups: “Price Oriented/Technology Adop...

  13. Towards a new orientation

    DEFF Research Database (Denmark)

    Froulund Jensen, Janet; Overgaard, Dorthe; Bestle, Morten H

    2017-01-01

    narrative of recovery was 'toward a trajectory of new orientation'. This narrative contained the chronological narratives of being 'at death's door', 'still not out of the woods' and 'on the road to recovery'. The road to recovery was described as downhill, steady-state or progressive. New orientation...... was obtained in steady-state or progressive recovery. CONCLUSIONS: This study provides a contemporary understanding of the process of intensive care recovery. Recovery evolves through narratives of mortal danger, risk of relapse and moving forward towards a new orientation in life. RELEVANCE TO CLINICAL...

  14. Developing a market orientation.

    Science.gov (United States)

    Hallums, A

    1994-03-01

    Developing a market-orientated organization is a complex task. An organization's market orientation is reflected in its ability to fulfil its customer's needs. The organization must look outside itself and adopt a flexible response to changing needs. This paper will examine what is meant by the term marketing and why it is necessary for an organization to incorporate the marketing concept. Analysis of the organization's culture and its relevance to the development of market orientation will also be considered. Reference will be made to health care where appropriate.

  15. The astronomical orientation of ancient Greek temples.

    Science.gov (United States)

    Salt, Alun M

    2009-11-19

    Despite its appearing to be a simple question to answer, there has been no consensus as to whether or not the alignments of ancient Greek temples reflect astronomical intentions. Here I present the results of a survey of archaic and classical Greek temples in Sicily and compare them with temples in Greece. Using a binomial test I show strong evidence that there is a preference for solar orientations. I then speculate that differences in alignment patterns between Sicily and Greece reflect differing pressures in the expression of ethnic identity.

  16. Patient Admission Preferences and Perceptions

    Science.gov (United States)

    Wu, Clayton; Melnikow, Joy; Dinh, Tu; Holmes, James F.; Gaona, Samuel D.; Bottyan, Thomas; Paterniti, Debora; Nishijima, Daniel K.

    2015-01-01

    Introduction Understanding patient perceptions and preferences of hospital care is important to improve patients’ hospitalization experiences and satisfaction. The objective of this study was to investigate patient preferences and perceptions of hospital care, specifically differences between intensive care unit (ICU) and hospital floor admissions. Methods This was a cross-sectional survey of emergency department (ED) patients who were presented with a hypothetical scenario of a patient with mild traumatic brain injury (TBI). We surveyed their preferences and perceptions of hospital care related to this scenario. A closed-ended questionnaire provided quantitative data on patient preferences and perceptions of hospital care and an open-ended questionnaire evaluated factors that may not have been captured with the closed-ended questionnaire. Results Out of 302 study patients, the ability for family and friends to visit (83%), nurse availability (80%), and physician availability (79%) were the factors most commonly rated “very important,” while the cost of hospitalization (62%) and length of hospitalization (59%) were the factors least commonly rated “very important.” When asked to choose between the ICU and the floor if they were the patient in the scenario, 33 patients (10.9%) choose the ICU, 133 chose the floor (44.0%), and 136 (45.0%) had no preference. Conclusion Based on a hypothetical scenario of mild TBI, the majority of patients preferred admission to the floor or had no preference compared to admission to the ICU. Humanistic factors such as the availability of doctors and nurses and the ability to interact with family appear to have a greater priority than systematic factors of hospitalization, such as length and cost of hospitalization or length of time in the ED waiting for an in-patient bed. PMID:26587095

  17. High Resolution Orientation Distribution Function

    DEFF Research Database (Denmark)

    Schmidt, Søren; Gade-Nielsen, Nicolai Fog; Høstergaard, Martin

    2012-01-01

    from the deformed material. The underlying mathematical formalism supports all crystallographic space groups and reduces the problem to solving a (large) set of linear equations. An implementation on multi-core CPUs and Graphical Processing Units (GPUs) is discussed along with an example on simulated...

  18. Electrodeposition of BaCO3 coatings on stainless steel substrates: Oriented growth in the presence of complexing agents

    Indian Academy of Sciences (India)

    Sumy Joseph; Sarala Upadhya; P Vishnu Kamath

    2009-09-01

    Electrodeposition of BaCO3 from aminecarboxylate stabilized-Ba(HCO3)2 baths, results in oriented crystallization when the bath conditions promote the decomposition of the Ba complex. Crystal growth is predominant along the -crystallographic axis. The crystallites orient themselves with their -axis normal to the substrate. The crystallites exhibit three-fold twinning (trilling) consequent to the evolution of the {110} planes as planes of reflection. Pairs of trillings are seen to grow about a four-sided polygon formed by the {010} crystal faces whose centre is a point of inversion.

  19. Interlimb Transfer of Grasp Orientation is Asymmetrical

    Directory of Open Access Journals (Sweden)

    Victor Frak

    2006-01-01

    Full Text Available One the most fundamental aspects of the human motor system is the hemispheric asymmetry seen in behavioral specialization. Hemispheric dominance can be inferred by a contralateral hand preference in grasping. Few studies have considered grasp orientation in the context of manual lateralization and none has looked at grasp orientation with natural prehension. Thirty right-handed adults performed precision grasps of a cylinder using the thumb and index fingers, and the opposition axis (OA was defined as the line connecting these two contact points on the cylinder. Subjects made ten consecutive grasps with one hand (primary hand movements followed by ten grasps with the other hand (trailing movements. Differences between primary and trailing grasps revealed that each hemisphere is capable of programming the orientation of the OA and that primary movements with the right hand significantly influenced OA orientation of the trailing left hand. These results extend the hemispheric dominance of the left hemisphere to the final positions of fingers during prehension.

  20. Trapping of Oxygen Vacancies at Crystallographic Shear Planes in Acceptor-Doped Pb-Based Ferroelectrics.

    Science.gov (United States)

    Batuk, Dmitry; Batuk, Maria; Tsirlin, Alexander A; Hadermann, Joke; Abakumov, Artem M

    2015-12-01

    The defect chemistry of the ferroelectric material PbTiO3 after doping with Fe(III) acceptor ions is reported. Using advanced transmission electron microscopy and powder X-ray and neutron diffraction, we demonstrate that even at concentrations as low as circa 1.7% (material composition approximately ABO2.95), the oxygen vacancies are trapped into extended planar defects, specifically crystallographic shear planes. We investigate the evolution of these defects upon doping and unravel their detailed atomic structure using the formalism of superspace crystallography, thus unveiling their role in nonstoichiometry in the Pb-based perovskites.